Science.gov

Sample records for bains par tubes

  1. Detection of inner tube defects in co-axial circle and Bain breathing systems: a comparison of occlusion and Pethick tests.

    PubMed

    Szypula, K A; Ip, J K; Bogod, D; Yentis, S M

    2008-10-01

    The performance of the occlusion and Pethick tests in detecting faulty inner tubes in co-axial circle and Bain systems was compared. Twelve co-axial circle and 12 Bain anaesthetic breathing systems were tested using the occlusion and the Pethick tests. For each system, three tubes were intact, and the remaining nine had a defect deliberately created in the inner tube (three proximal, three middle and three distal). The investigators were blinded to which of the tubes were defective, and to each other's results. The results showed 100% specificity for both tests. The sensitivity of the occlusion test for detecting faulty breathing systems was found to be good (98%). Our results suggest that the occlusion test should be performed in preference to the Pethick test when testing co-axial circle and Bain systems.

  2. Brulures Profondes des Membres Apres Intoxication au Co Par Usage du Barbecue Traditionnel en Salle de Bain

    PubMed Central

    Chraïbi, R.; Moussaoui, A.; Tourabi, K.; Ennouhi, A.; Ihrai, H.; Hassam, B.

    2007-01-01

    Summary En l'absence des moyens de chauffage moderne à domicile chez une proportion non négligeable des Marocains, le recours au moyen traditionnel est fréquent. A travers six observations de brûlures profondes des membres, particulières par leur mode de survenue et par leur gravité, les Auteurs attirent l'attention sur le danger de l'utilisation du barbecue traditionnel «majmer» pour réchauffement en milieu clos. PMID:21991072

  3. Modified occlusion tests for the Bain breathing system.

    PubMed

    Heath, P J; Marks, L F

    1991-03-01

    Undetected defects in the inner tube of the Bain coaxial anaesthetic breathing system may result in a greatly increased apparatus deadspace. Several authorities have advocated tests intended to detect inner tube problems; however, the efficacy of these tests has never been validated. In this study none of the tests were able to detect all the induced defects. A modification of an existing test using the backbar pressure-relief valve and a new double occlusion test were sufficiently sensitive to detect all defects.

  4. David Baines: Rural Doctor, Lecturer, Dancer.

    ERIC Educational Resources Information Center

    Wisecarver, Charmaine

    1993-01-01

    Discusses the career of David Baines, an American Indian doctor who successfully integrates traditional and modern medicine. Describes problems faced by American Indian doctors, the tremendous amount of work involved in medical training, and problems associated with working in rural areas and trying to straddle two opposing cultures when…

  5. 76 FR 76710 - Baine, Edward H.; Notice of Filing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-08

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Baine, Edward H.; Notice of Filing Take notice that on December 1, 2011, Edward H. Baine submitted for filing, an application for authority to hold interlocking...

  6. The Intellectual Background of Alexander Bain's "Models of Discourse."

    ERIC Educational Resources Information Center

    Harned, Jon

    1985-01-01

    Explores the discourse modes put forth in Bain's nineteenth century college textbook "English Composition and Rhetoric." Discusses his rationale for shifting from the previous belletristic schemes to the forms of description, narration, exposition, persuasion, and poetry. (HTH)

  7. Pars tensa retraction pockets in children: treatment by excision and ventilation tube insertion.

    PubMed

    Srinivasan, V; Banhegyi, G; O'Sullivan, G; Sherman, I W

    2000-08-01

    Tympanic membrane retraction pockets involving the pars tensa are not uncommon in clinical practice. Recurrent infections, ossicular erosion and cholesteatoma are the recognized sequelae. The management options include surveillance, medical treatment and surgery. The surgical procedures range from grommet insertion to extensive tympanoplasty procedures. We report our experience with simple excision and grommet insertion, performed in 31 ears in 26 patients as day cases. The follow-up ranged from 8 to 34 months with a mean of 16 months. The procedure was successful in 23 ears (success rate of 74%). Recurrence of retraction occurred in seven ears and in one ear there was a persistent perforation. Age, previous grommet insertion and severity of retraction did not have a statistically significant influence on the final outcome. We conclude that excision and grommet insertion is a simple, safe and efficient procedure for the management of tympanic membrane retraction pockets and can be considered in preference to extensive tympanoplasty. PMID:10971530

  8. Humidity of the Bain and circle systems reassessed.

    PubMed

    Bengtson, J P; Bengtson, A; Sonander, H; Stenqvist, O

    1989-07-01

    The humidity outputs of the Bain circuit, a traditional non-coaxial Mapleson D system, and a circle system with and without a soda lime absorber were evaluated in a laboratory model simulating a 70-kg subject. The breathing systems were tested with tidal volumes of 0.35 and 0.70 L and frequencies of 10-20 breaths/min to maintain an end-expiratory CO2 of 4.5%. There were small differences in inspiratory gas humidity between the Bain and the non-coaxial Mapleson D system. With a fresh gas flow of 5 L/min in the Bain circuit, the humidity was 9.8-16.5 mg H2O/L depending on tidal volume and respiratory frequency. The humidity output of the circle absorber system with fresh gas flows of 0.5 or 2 L/min was 21.6-25.2 mg H2O/L at 60 min. Therefore, this study does not support previous studies, which propose that the Bain circuit has superior humidifying properties compared with those of the circle absorber system.

  9. Alexander Bain's CUE in the Post-Modern World: Unity Revisited.

    ERIC Educational Resources Information Center

    Dryden, Phyllis

    In 1866, Alexander Bain proposed that by evaluating unity, coherence, and emphasis (which he brought together under the acronym "CUE"), students could judge the effectiveness of their written paragraphs. One hundred twenty-five years later, the proposition is still central to composition instruction. A review of modern writing textbooks reveals…

  10. Étude par analogie électrique de différents types de tubes à gaz pulsé : modélisation et expérience

    NASA Astrophysics Data System (ADS)

    Halouane, A.; Maréchal, J.-C.; David, M.

    1998-10-01

    The main purpose of this paper is to explain the operation of pulse tubes refrigerators (PTR) by a network theory approach: the voltage and the current represent respectively the hydrodynamic parameters pressure P and mass flow rate m of the system. Each impedance is treated as a circuit of equivalent electrical element: resistance, capacitance or inductance. At the hot end of the PTR, different phase shift systems are modelled in the same way and could be compared, as the orifice pulse tube refrigerator (OPTR), the double inlet pulse tube refrigerator (DIPTR), the modified pulse tube refrigerator (MPTR) whose phasor is a moving piston at the hot end, the hybrid pulse tube refrigerator (HPTR) with a sequential orifice opening and the OPTR with inertance (IOPTR). By combining the network approach with the thermal analysis of the regenerator and the thermodynamic analysis of the tube it is possible to predict the energy balance at the cold end: extracted power, regenerator and tube losses and the influence of dead volumes. Different solutions were pointed out to treat this model. If the parameters are not sinusoidal the system might be treated at an order greater than 1. This modelling was used to design a miniature PTR operating at high frequency (20-50) Hz and pressure higher than 2 MPa, developed in collaboration with “Air Liquide" firm. The rotary or linear compressor used has 1 cm3 swept-volume and is similar to that used on Stirling refrigerator and generate a quasi-sinusoidal pressure wave. Under a mean pressure of 3 MPa and a 27.5 Hz operating frequency, the lower temperature reached is 49 K with an available power of 1 W at 84 K, in a double inlet mode. Le principal objectif de cet article est de présenter le fonctionnement des tubes à gaz pulsé (TGP) par une analogie électrique [CITE] où la tension et le courant représentent les paramètres hydrodynamiques pression P et débit massique m du système. Toute impédance peut être traitée comme un

  11. Enhanced thermoelectric performance of (Ba,In) double-filled skutterudites via randomly arranged micropores

    SciTech Connect

    Yu, Jian; Zhao, Wen-Yu E-mail: zhangqj@whut.edu.cn; Wei, Ping; Zhu, Wan-Ting; Zhou, Hong-Yu; Liu, Zhi-Yuan; Tang, Ding-Guo; Lei, Bing; Zhang, Qing-Jie E-mail: zhangqj@whut.edu.cn

    2014-04-07

    Porous (Ba,In) double-filled skutterudite materials with pore diameter about 1–4 μm were prepared by the decomposition of metastable ZnSb inclusions induced by the Zn sublimation. Transport measurements revealed that the Seebeck coefficient was increased due to the electron filtering effect induced by nanostructures in the surfaces of pores, the electrical conductivity was almost unchanged because of the percolation effect of conducted network composed of filled skutterudites, and the lattice thermal conductivity was dramatically suppressed due to the enhanced pore-edge boundary scattering of long-wavelength phonons. As a result, a maximum ZT of 1.36 was obtained, increased by 22.5% as compared to that of the bulk material with same chemical composition. This work demonstrates that by introducing porous structures is thought to be an efficient approach to improve the thermoelectric performance of bulk materials.

  12. Getting off the Bain path: Are there any metastable states of cubic elements?

    NASA Astrophysics Data System (ADS)

    Mehl, Michael J.; Boyer, Larry L.

    2003-03-01

    Body-centered and face-centered cubic crystals can be considered as special cases of a body-centered tetragonal crystal with c/a = 1 and 2, respectively. First-principles calculations along this Bain path show that elements with an fcc (bcc) ground state are elastically unstable with respect to a tetragonal distortion in the bcc (fcc) phase. Starting with a normally fcc element and calculating E(c/a) for c/a < 1 we find a local minimum near c/a = 2/3, while for a bcc element we find a local minimum at some c/a > 2. It is tempting to conclude that these bct minima, which are required by continuity, are metastable, but calculations by several authors show that, at least for Al, Cu, and Pd, the bct structures are unstable with respect to an orthorhombic distortion. We use a simple "magic strain" construction(L. L. Boyer, Acta Cryst. A) 45, FC29 (1989).(M. J. Mehl and L. L. Boyer, Phys. Rev. B) 43, 9498 (1991). to study the stability of these bct states, and present examples which suggest that no fcc or bcc element has a metastable bct state.

  13. Tube support

    DOEpatents

    Mullinax, Jerry L.

    1988-01-01

    A tube support for supporting horizontal tubes from an inclined vertical support tube passing between the horizontal tubes. A support button is welded to the vertical support tube. Two clamping bars or plates, the lower edges of one bearing on the support button, are removably bolted to the inclined vertical tube. The clamping bars provide upper and lower surface support for the horizontal tubes.

  14. Feeding Tubes

    MedlinePlus

    ... administer the TPN. Tubes Used for Enteral Feeds NG (Nasogastric Tube) A flexible tube is placed via ... down through the esophagus into the stomach. The NG tube can be used to empty the stomach ...

  15. Ear Tubes

    MedlinePlus

    ... Meeting Calendar Find an ENT Doctor Near You Ear Tubes Ear Tubes Patient Health Information News media ... and throat specialist) may be considered. What are ear tubes? Ear tubes are tiny cylinders placed through ...

  16. De Par en Par (Wide Open), 1993.

    ERIC Educational Resources Information Center

    De Par en Par, 1993

    1993-01-01

    This document consists of the four issues of the serial "De Par en Par" published during 1993. This serial provides lessons in Spanish for elementary school children. It is written by bilingual education teachers for use in the bilingual classroom. The magazine bases itself on the K-6 curriculum and offers a variety of activities for classroom…

  17. Effects of a heat and moisture exchanger on carbon dioxide equilibrium during mechanical ventilation with the Bain circuit.

    PubMed

    Romano, E; Gullo, A; Vacri, A; Bonifacio, R; Caristi, D

    1987-05-01

    The introduction of a heat and moisture exchanger (HME) into the anaesthetic circuit may cause a rise in carbon dioxide (CO2) tension through an increase in dead space. We studied the effects of the Ultipor Pall BB50 filter included 'in series' in the Bain circuit on CO2 equilibrium. Arterial carbon dioxide tension (PaCO2) was measured in 81 patients scheduled for elective surgery before and after the insertion of the filter. Results showed that: females were always more hyperventilated than males when fresh gas flow was set at 70 ml kg-1 ideal body weight; the inclusion of the filter increased the PaCO2 in the group as a whole (the difference was statistically, but not clinically, significant); PaCO2 increased after the application of the filter only in females; the effects of the filter were completely independent of the patient's age. It is concluded that the use of the Ultipor Pall BB50 filter is a safe procedure during mechanical ventilation with the Bain breathing system and there is no need to modify ventilation.

  18. TUBE TESTER

    DOEpatents

    Gittings, H.T. Jr.; Kalbach, J.F.

    1958-01-14

    This patent relates to tube testing, and in particular describes a tube tester for automatic testing of a number of vacuum tubes while in service and as frequently as may be desired. In it broadest aspects the tube tester compares a particular tube with a standard tube tarough a difference amplifier. An unbalanced condition in the circuit of the latter produced by excessive deviation of the tube in its characteristics from standard actuates a switch mechanism stopping the testing cycle and indicating the defective tube.

  19. Pars Injuries in Athletes.

    PubMed

    Oren, Jonathan H; Gallina, Jason M

    2016-03-01

    Pars injuries are common causes of low back pain in adolescent athletes. Workup traditionally has included lumbar radiographs with oblique views and single-photon emission computed tomography (SPECT). However, recent literature has demonstrated the accuracy of MRI as a diagnostic modality. Acute injuries may be amenable to bracing with the goal of a healed lesion. Most cases of spondylolysis will result in asymptomatic non-union, though pars repair is an option for symptomatic pars defects without spondylolisthesis. PMID:26977552

  20. Nonconsecutive Pars Interarticularis Defects.

    PubMed

    Elgafy, Hossein; Hart, Ryan C; Tanios, Mina

    2015-12-01

    Lumbar spondylolysis is a well-recognized condition occurring in adolescents because of repetitive overuse in sports. Nonconsecutive spondylolysis involving the lumbar spine is rare. In contrast to single-level pars defects that respond well to conservative treatment, there is no consensus about the management of multiple-level pars fractures; a few reports indicated that conservative management is successful, and the majority acknowledged that surgery is often required. The current study presents a rare case of pars fracture involving nonconsecutive segments and discusses the management options. In this case report, we review the patient's history, clinical examination, radiologic findings, and management, as well as the relevant literature. An 18-year-old man presented to the clinic with worsening lower back pain related to nonconsecutive pars fractures at L2 and L5. After 6 months of conservative management, diagnostic computed tomography-guided pars block was used to localize the symptomatic level at L2, which was treated surgically; the L5 asymptomatic pars fracture did not require surgery. At the last follow-up 2 years after surgery, the patient was playing baseball and basketball, and denied any back pain. This article reports a case of rare nonconsecutive pars fractures. Conservative management for at least 6 months is recommended. Successful management depends on the choice of appropriate treatment for each level. Single-photon emission computed tomography scan, and computed tomography-guided pars block are valuable preoperative tools to identify the symptomatic level in such a case. PMID:26665257

  1. Nonconsecutive Pars Interarticularis Defects.

    PubMed

    Elgafy, Hossein; Hart, Ryan C; Tanios, Mina

    2015-12-01

    Lumbar spondylolysis is a well-recognized condition occurring in adolescents because of repetitive overuse in sports. Nonconsecutive spondylolysis involving the lumbar spine is rare. In contrast to single-level pars defects that respond well to conservative treatment, there is no consensus about the management of multiple-level pars fractures; a few reports indicated that conservative management is successful, and the majority acknowledged that surgery is often required. The current study presents a rare case of pars fracture involving nonconsecutive segments and discusses the management options. In this case report, we review the patient's history, clinical examination, radiologic findings, and management, as well as the relevant literature. An 18-year-old man presented to the clinic with worsening lower back pain related to nonconsecutive pars fractures at L2 and L5. After 6 months of conservative management, diagnostic computed tomography-guided pars block was used to localize the symptomatic level at L2, which was treated surgically; the L5 asymptomatic pars fracture did not require surgery. At the last follow-up 2 years after surgery, the patient was playing baseball and basketball, and denied any back pain. This article reports a case of rare nonconsecutive pars fractures. Conservative management for at least 6 months is recommended. Successful management depends on the choice of appropriate treatment for each level. Single-photon emission computed tomography scan, and computed tomography-guided pars block are valuable preoperative tools to identify the symptomatic level in such a case.

  2. A first-principles investigation on the effects of magnetism on the Bain transformation of α-phase FeNi systems

    NASA Astrophysics Data System (ADS)

    Rahman, Gul; Gee Kim, In; Bhadeshia, H. K. D. H.

    2012-03-01

    The effects of magnetism on the Bain transformation of α-phase FeNi systems are investigated by using the full potential linearized augmented plane wave method based on the generalized gradient approximation. We found that Ni impurity in bcc Fe increases the lattice constant in the ferromagnetic (FM) states, but not in the nonmagnetic (NM) states. The shear modulus, G, and Young's modulus, E, of bcc Fe are also increased by raising the concentration of nickel. All the compositions considered show high shear anisotropy, and the ratio of the bulk to shear modulus is greater than 1.75, implying ductility. The mean sound velocities in the [100] directions are greater than in the [110] directions. The Bain transformation, which is a component of martensitic transformation, has also been studied to reveal that NixFe1-x alloys are elastically unstable in the NM states, but not so in the FM states. The electronic structures explain these results in terms of the density of states at the Fermi level. It is evident that magnetism cannot be neglected when dealing with the Bain transformation in iron and its alloys.

  3. Par Pond water balance

    SciTech Connect

    Hiergesell, R.A.; Dixon, K.L.

    1996-06-01

    A water budget for the Par Pond hydrologic system was established in order to estimate the rate of groundwater influx to Par Pond. This estimate will be used in modeling exercises to predict Par Pond reservoir elevation and spillway discharge in the scenario where Savannah River water is no longer pumped and discharged into Par Pond. The principal of conservation of mass was used to develop the water budget, where water inflow was set equal to water outflow. Components of the water budget were identified, and the flux associated with each was determined. The water budget was considered balanced when inflow and outflow summed to zero. The results of this study suggest that Par Pond gains water from the groundwater system in the upper reaches of the reservoir, but looses water to the groundwater system near the dam. The rate of flux of groundwater from the water table aquifer into Par Pond was determined to be 13 cfs. The rate of flux from Par Pond to the water table aquifer near the dam was determined to be 7 cfs.

  4. Ground-Water Flow, 2004-07, and Water Quality, 1992-2007, in McBaine Bottoms, Columbia, Missouri

    USGS Publications Warehouse

    Smith, Brenda Joyce; Richards, Joseph M.

    2008-01-01

    The U.S. Geological Survey, in cooperation with the city of Columbia, Missouri, and the Missouri Department of Conservation, collected ground-water quality data, surface-water quality data, and water-level data in McBaine Bottoms, southwest of Columbia. McBaine Bottoms, adjacent to the Missouri River, is the location of the municipal-supply well field for the city of Columbia, the city of Columbia wastewater-treatment wetlands, and the Missouri Department of Conservation Eagle Bluffs Conservation Area. This report describes the ground-water flow and water quality of McBaine Bottoms and provides information to better understand the interaction between treated effluent from the wetlands used on the Eagle Bluffs Conservation Area and the water in the alluvial aquifer that is pumped from the city of Columbia municipal-supply well field. Changes in major chemical constituent concentrations have been detected at several sampling sites between pre- and post-effluent application data. Analysis of post-effluent data indicates substantial changes in calcium, potassium, sodium, chloride, and sulfate concentrations in ground water. These changes became apparent shortly after the beginning of the operation of the wastewater-treatment wetland in 1994 and the formation of the Eagle Bluffs Conservation Area, which uses the treated effluent as a water source for the management of migratory water fowl. The changes have continued throughout the 15 years of sample collection. The concentrations of these major chemical constituents are on the mixing continuum between pre-effluent ground water as one end member and the treated wastewater effluent as the other end member. For monitoring wells that had changes in major chemical constituent concentrations, the relative percentage of treated effluent in the ground water, assuming chloride is conservative, ranged from 6 to 88 percent. Twenty-two monitoring wells throughout McBaine Bottoms have been affected by effluent based on chloride

  5. THE MEASURES PAR PROJECT

    NASA Astrophysics Data System (ADS)

    Frouin, R. J.; Franz, B.

    2009-12-01

    The solar energy available for photosynthesis, known as PAR, controls the growth of phytoplankton and, therefore, regulates the composition and evolution of marine ecosystems. Knowing the spatial and temporal distribution of PAR over the oceans is critical to understanding biogeochemical cycles of carbon, nutrients, and oxygen, and to address important climate and global change issues such as the fate of anthropogenic atmospheric carbon dioxide. In view of this, a 12-year time series of PAR at the ocean surface, starting in September 1997, is being produced by the NASA Ocean Biology Processing Group from SeaWiFS, MODIS-Terra, and MODIS-Aqua data. The product covers the global oceans, with a spatial resolution of about 9.3x9.3 km (equal area grid) and a temporal resolution of one day. PAR is computed as the difference between the 400-700 nm solar flux incident on the top of the atmosphere (known) and reflected back to space by the atmosphere and surface (derived from satellite radiance), taking into account atmospheric absorption (modeled). Knowledge of pixel composition is not required, eliminating the need for cloud screening and arbitrary assumptions about sub-pixel cloudiness. Combining data from satellite sensors with different equatorial crossing times accounts for the diurnal variability of clouds and, therefore, increases accuracy on a daily time scale. The processing system, including routine check of accuracy and control of quality, is designed to operate during the entire lifetime of SeaWiFS and MODIS, and to accommodate future sensors with ocean-color capabilities. Maps of daily, weekly, and monthly PAR obtained from individual sensors are presented, as well as merged products. Accuracy is quantified in comparisons with other satellite estimates, the National Centers for Environmental Prediction reanalysis product, and in-situ measurements from fixed buoys and platforms. The good statistical performance makes the satellite PAR product suitable for large

  6. Nasogastric feeding tube

    MedlinePlus

    Feeding - nasogastric tube; NG tube; Bolus feeding; Continuous pump feeding; Gavage tube ... A nasogastric tube (NG tube) is a special tube that carries food and medicine to the stomach through the nose. It can be ...

  7. Feeding tube insertion - gastrostomy

    MedlinePlus

    ... tube insertion; G-tube insertion; PEG tube insertion; Stomach tube insertion; Percutaneous endoscopic gastrostomy tube insertion ... and down the esophagus, which leads to the stomach. After the endoscopy tube is inserted, the skin ...

  8. La pelade par plaques

    PubMed Central

    Spano, Frank; Donovan, Jeff C.

    2015-01-01

    Résumé Objectif Présenter aux médecins de famille des renseignements de base pour faire comprendre l’épidémiologie, la pathogenèse, l’histologie et l’approche clinique au diagnostic de la pelade par plaques. Sources des données Une recension a été effectuée dans PubMed pour trouver des articles pertinents concernant la pathogenèse, le diagnostic et le pronostic de la pelade par plaques. Message principal La pelade par plaques est une forme de perte pileuse auto-immune dont la prévalence durant une vie est d’environ 2 %. Des antécédents personnels ou familiaux de troubles auto-immuns concomitants, comme le vitiligo ou une maladie de la thyroïde, peuvent être observés dans un petit sous-groupe de patients. Le diagnostic peut souvent être posé de manière clinique en se fondant sur la perte de cheveux non cicatricielle et circulaire caractéristique, accompagnée de cheveux en « point d’exclamation » en périphérie chez ceux dont le problème en est aux premiers stades. Le diagnostic des cas plus complexes ou des présentations inhabituelles peut être facilité par une biopsie et un examen histologique. Le pronostic varie largement et de mauvais résultats sont associés à une apparition à un âge précoce, une perte importante, la variante ophiasis, des changements aux ongles, des antécédents familiaux ou des troubles auto-immuns concomitants. Conclusion La pelade par plaques est une forme auto-immune de perte de cheveux périodiquement observée en soins primaires. Les médecins de famille sont bien placés pour identifier la pelade par plaques, déterminer la gravité de la maladie et poser le diagnostic différentiel approprié. De plus, ils sont en mesure de renseigner leurs patients à propos de l’évolution clinique de la maladie ainsi que du pronostic général selon le sous-type de patients.

  9. Geochemical behaviour of Radium isotopes and Radon in a coastal thermal system (Balaruc-les-Bains, South of France)

    NASA Astrophysics Data System (ADS)

    Condomines, Michel; Gourdin, Elian; Gataniou, Delphine; Seidel, Jean-Luc

    2012-12-01

    The behaviour of the four Ra isotopes (measured by gamma spectrometry) and 222Rn (measured with an AlphaGUARD ionisation chamber) has been investigated in NaCl-rich thermal waters of Balaruc-les-Bains on the Mediterranean coast (South of France). This study allows identification of the deep thermal water signature and reveals the influence of seawater or karst water inflows on Ra isotopes and 222Rn. The deep thermal water has 226Ra and 222Rn activities of 840 and 1900 mBq/l, respectively, a (228Ra/226Ra) activity ratio of 0.59, and low (224Ra/228Ra) and (223Ra/226Ra) ratios of 0.67 and 0.025, respectively. Several arguments suggest a dominant role of radioactive decay for short-lived Ra isotopes and Rn during the relatively rapid ascent of thermal water through wide open fractures and drains. The low (223Ra/226Ra) ratio constrains the maximum ascent velocity of thermal water to 8-10 m/h. Seawater inflow into the hydrothermal system results in an enrichment in short-lived Ra isotopes and 222Rn. The high (223Ra/226Ra) ratio (0.23) suggests that 223Ra, 224Ra and 222Rn produced by alpha-recoil in the upper-Jurassic limestone are entrained by seawater percolation through the coastal basement, due to active pumping in one of the near shore production well. This process would be enhanced by a low water/rock ratio (i.e. in a low-porosity, micro-fractured limestone). Mixing of this enriched seawater with thermal water induces barite precipitation with co-precipitation of a large fraction of Ra. Short-lived Ra isotopes may thus be useful tracers of seawater flux towards the continent. Conversely, the inflow and mixing of karst groundwater result in a general dilution of all dissolved elements, only a small enrichment in 224Ra and 223Ra, but a large enrichment in 222Rn (up to 26 Bq/l). The combination of Ra isotopes and 222Rn data provides a good way to trace the dynamics of different water masses along coastal areas.

  10. Protective tubes for sodium heated water tubes

    DOEpatents

    Essebaggers, Jan

    1979-01-01

    A heat exchanger in which water tubes are heated by liquid sodium which minimizes the results of accidental contact between the water and the sodium caused by failure of one or more of the water tubes. A cylindrical protective tube envelopes each water tube and the sodium flows axially in the annular spaces between the protective tubes and the water tubes.

  11. Multiple tube premixing device

    DOEpatents

    Uhm, Jong Ho; Naidu, Balachandar; Ziminksy, Willy Steve; Kraemer, Gilbert Otto; Yilmaz, Ertan; Lacy, Benjamin; Stevenson, Christian; Felling, David

    2013-08-13

    The present application provides a premixer for a combustor. The premixer may include a fuel plenum with a number of fuel tubes and a burner tube with a number of air tubes. The fuel tubes extend about the air tubes.

  12. Multiple tube premixing device

    DOEpatents

    Uhm, Jong Ho; Varatharajan, Balachandar; Ziminsky, Willy Steve; Kraemer, Gilbert Otto; Yilmaz, Ertan; Lacy, Benjamin; Stevenson, Christian; Felling, David

    2012-12-11

    The present application provides a premixer for a combustor. The premixer may include a fuel plenum with a number of fuel tubes and a burner tube with a number of air tubes. The fuel tubes extend about the air tubes.

  13. Ear tube insertion

    MedlinePlus

    Myringotomy; Tympanostomy; Ear tube surgery; Pressure equalization tubes; Ventilating tubes; Ear infection - tubes; Otitis - tubes ... trapped fluid can flow out of the middle ear. This prevents hearing loss and reduces the risk ...

  14. La pelade par plaques

    PubMed Central

    Spano, Frank; Donovan, Jeff C.

    2015-01-01

    Résumé Objectif Présenter aux médecins de famille des renseignements de base pour faire comprendre les schémas thérapeutiques et les résultats des traitements pour la pelade par plaques, de même que les aider à identifier les patients pour qui une demande de consultation en dermatologie pourrait s’imposer. Sources des données Une recension a été effectuée dans PubMed pour trouver des articles pertinents concernant le traitement de la pelade par plaques. Message principal La pelade par plaques est une forme auto-immune de perte pileuse qui touche à la fois les enfants et les adultes. Même s’il n’y a pas de mortalité associée à la maladie, la morbidité découlant des effets psychologiques de la perte des cheveux peut être dévastatrice. Lorsque la pelade par plaques et le sous-type de la maladie sont identifiés, un schéma thérapeutique approprié peut être amorcé pour aider à arrêter la chute des cheveux et possiblement faire commencer la repousse. Les traitements de première intention sont la triamcinolone intralésionnelle avec des corticostéroïdes topiques ou du minoxidil ou les 2. Les médecins de famille peuvent prescrire ces traitements en toute sécurité et amorcer ces thérapies. Les cas plus avancés ou réfractaires pourraient avoir besoin de diphénylcyclopropénone topique ou d’anthraline topique. On peut traiter la perte de cils avec des analogues de la prostaglandine. Les personnes ayant subi une perte de cheveux abondante peuvent recourir à des options de camouflage ou à des prothèses capillaires. Il est important de surveiller les troubles psychiatriques en raison des effets psychologiques profonds de la perte de cheveux. Conclusion Les médecins de famille verront de nombreux patients qui perdent leurs cheveux. La reconnaissance de la pelade par plaques et la compréhension du processus pathologique sous-jacent permettent d’amorcer un schéma thérapeutique approprié. Les cas plus graves ou r

  15. Tube Feedings.

    ERIC Educational Resources Information Center

    Plummer, Nancy

    This module on tube feedings is intended for use in inservice or continuing education programs for persons who work in long-term care. Instructor information, including teaching suggestions and a listing of recommended audiovisual materials and their sources appear first. The module goal and objectives are then provided. A brief discussion follows…

  16. Angular glass tubing drawn from round tubing

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Round glass tubing softened in a furnace is drawn over a shaped plug or mandel to form shapes with other than a circular cross section. Irregularly shaped tubing is formed without limitations on tube length or wall thickness.

  17. Neutron tubes

    DOEpatents

    Leung, Ka-Ngo; Lou, Tak Pui; Reijonen, Jani

    2008-03-11

    A neutron tube or generator is based on a RF driven plasma ion source having a quartz or other chamber surrounded by an external RF antenna. A deuterium or mixed deuterium/tritium (or even just a tritium) plasma is generated in the chamber and D or D/T (or T) ions are extracted from the plasma. A neutron generating target is positioned so that the ion beam is incident thereon and loads the target. Incident ions cause D-D or D-T (or T-T) reactions which generate neutrons. Various embodiments differ primarily in size of the chamber and position and shape of the neutron generating target. Some neutron generators are small enough for implantation in the body. The target may be at the end of a catheter-like drift tube. The target may have a tapered or conical surface to increase target surface area.

  18. QUANTIZING TUBE

    DOEpatents

    Jensen, A.S.; Gray, G.W.

    1958-07-01

    Beam deflection tubes are described for use in switching or pulse amplitude analysis. The salient features of the invention reside in the target arrangement whereby outputs are obtained from a plurality of collector electrodes each correspondlng with a non-overlapping range of amplitudes of the input sigmal. The tube is provded with mcans for deflecting the electron beam a1ong a line in accordance with the amplitude of an input signal. The target structure consists of a first dymode positioned in the path of the beam wlth slots spaced a1ong thc deflection line, and a second dymode posltioned behind the first dainode. When the beam strikes the solid portions along the length of the first dymode the excited electrons are multiplied and collected in separate collector electrodes spaced along the beam line. Similarly, the electrons excited when the beam strikes the second dynode are multiplied and collected in separate electrodes spaced along the length of the second dyode.

  19. Electron tube

    DOEpatents

    Suyama, Motohiro; Fukasawa, Atsuhito; Arisaka, Katsushi; Wang, Hanguo

    2011-12-20

    An electron tube of the present invention includes: a vacuum vessel including a face plate portion made of synthetic silica and having a surface on which a photoelectric surface is provided, a stem portion arranged facing the photoelectric surface and made of synthetic silica, and a side tube portion having one end connected to the face plate portion and the other end connected to the stem portion and made of synthetic silica; a projection portion arranged in the vacuum vessel, extending from the stem portion toward the photoelectric surface, and made of synthetic silica; and an electron detector arranged on the projection portion, for detecting electrons from the photoelectric surface, and made of silicon.

  20. Tube Feeding Troubleshooting Guide

    MedlinePlus

    ... profile tube also has a stem length). Note: NG and NJ tubes (that go through a person’s ... Immediate Action: • Discontinue feeding. • If you have an NG or NJ tube, and the tube is curled ...

  1. Chest tube insertion

    MedlinePlus

    Chest drainage tube insertion; Insertion of tube into chest; Tube thoracostomy; Pericardial drain ... When your chest tube is inserted, you will lie on your side or sit partly upright, with one arm over your head. Sometimes, ...

  2. Tube furnace

    DOEpatents

    Foster, Kenneth G.; Frohwein, Eugene J.; Taylor, Robert W.; Bowen, David W.

    1991-01-01

    A vermiculite insulated tube furnace is heated by a helically-wound resistance wire positioned within a helical groove on the surface of a ceramic cylinder, that in turn is surroundingly disposed about a doubly slotted stainless steel cylindrical liner. For uniform heating, the pitch of the helix is of shorter length over the two end portions of the ceramic cylinder. The furnace is of large volume, provides uniform temperature, offers an extremely precise programmed heating capability, features very rapid cool-down, and has a modest electrical power requirement.

  3. Tapered pulse tube for pulse tube refrigerators

    DOEpatents

    Swift, Gregory W.; Olson, Jeffrey R.

    1999-01-01

    Thermal insulation of the pulse tube in a pulse-tube refrigerator is maintained by optimally varying the radius of the pulse tube to suppress convective heat loss from mass flux streaming in the pulse tube. A simple cone with an optimum taper angle will often provide sufficient improvement. Alternatively, the pulse tube radius r as a function of axial position x can be shaped with r(x) such that streaming is optimally suppressed at each x.

  4. Collapse Tubes

    NASA Technical Reports Server (NTRS)

    2006-01-01

    [figure removed for brevity, see original site] Context image for PIA02154 Collapse Tubes

    The discontinuous channels in this image are collapsed lava tubes.

    Image information: VIS instrument. Latitude -19.7N, Longitude 317.5E. 17 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

  5. A tube-in-tube thermophotovoltaic generator

    SciTech Connect

    Ashcroft, J.; Campbell, B.; Depoy, D.

    1996-12-31

    A thermophotovoltaic device includes at least one thermal radiator tube, a cooling tube concentrically disposed within each thermal radiator tube and an array of thermophotovoltaic cells disposed on the exterior surface of the cooling tube. A shell having a first end and a second end surrounds the thermal radiator tube. Inner and outer tubesheets, each having an aperture corresponding to each cooling tube, are located at each end of the shell. The thermal radiator tube extends within the shell between the inner tubesheets. The cooling tube extends within the shell through the corresponding apertures of the two inner tubesheets to the corresponding apertures of the two outer tubesheets. A plurality of the thermal radiator tubes can be arranged in a staggered or an in-line configuration within the shell.

  6. Tube-in-tube thermophotovoltaic generator

    DOEpatents

    Ashcroft, John; Campbell, Brian; DePoy, David

    1998-01-01

    A thermophotovoltaic device includes at least one thermal radiator tube, a cooling tube concentrically disposed within each thermal radiator tube and an array of thermophotovoltaic cells disposed on the exterior surface of the cooling tube. A shell having a first end and a second end surrounds the thermal radiator tube. Inner and outer tubesheets, each having an aperture corresponding to each cooling tube, are located at each end of the shell. The thermal radiator tube extends within the shell between the inner tubesheets. The cooling tube extends within the shell through the corresponding apertures of the two inner tubesheets to the corresponding apertures of the two outer tubesheets. A plurality of the thermal radiator tubes can be arranged in a staggered or an in-line configuration within the shell.

  7. Tube-in-tube thermophotovoltaic generator

    DOEpatents

    Ashcroft, J.; Campbell, B.; DePoy, D.

    1998-06-30

    A thermophotovoltaic device includes at least one thermal radiator tube, a cooling tube concentrically disposed within each thermal radiator tube and an array of thermophotovoltaic cells disposed on the exterior surface of the cooling tube. A shell having a first end and a second end surrounds the thermal radiator tube. Inner and outer tubesheets, each having an aperture corresponding to each cooling tube, are located at each end of the shell. The thermal radiator tube extends within the shell between the inner tubesheets. The cooling tube extends within the shell through the corresponding apertures of the two inner tubesheets to the corresponding apertures of the two outer tubesheets. A plurality of the thermal radiator tubes can be arranged in a staggered or an in-line configuration within the shell. 8 figs.

  8. Par Pond vegetation status 1996

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1996-12-01

    The water level of Par Pond was lowered approximately 20 feet in mid-1991 in order to protect downstream residents from possible dam failure suggested by subsidence on the downstream slope of the dam and to repair the dam. This lowering exposed both emergent and nonemergent macrophyte beds to drying conditions resulting in extensive losses. A survey of the newly emergent, shoreline aquatic plant communities of Par Pond began in June 1995, three months after the refilling of Par Pond to approximately 200 feet above mean sea level. These surveys continued in July, September, and late October, 1995, and into the early spring and late summer of 1996. Communities similar to the pre-drawdown, Par Pond aquatic plant communities continue to become re-established. Emergent beds of maidencane, lotus, waterlily, watershield, and Pontederia are extensive and well developed. Measures of percent cover, width of beds, and estimates of area of coverage with satellite data indicate regrowth within two years of from 40 to 60% of levels prior to the draw down. Cattail occurrence continued to increase during the summer of 1996, especially in the former warm arm of Par Pond, but large beds common to Par Pond prior to the draw down still have not formed. Lotus has invaded and occupies many of the areas formerly dominated by cattail beds. To track the continued development of macrophytes in Par Pond, future surveys through the summer and early fall of 1997, along with the evaluation of satellite data to map the extent of the macrophyte beds of Par Pond, are planned.

  9. Gastrostomy feeding tube - bolus

    MedlinePlus

    Feeding - gastrostomy tube - bolus; G-tube - bolus; Gastrostomy button - bolus; Bard Button - bolus; MIC-KEY - bolus ... Your child's gastrostomy tube (G-tube) is a special tube in your child's stomach that will help deliver food and medicines until your ...

  10. Heat exchanger tube mounts

    DOEpatents

    Wolowodiuk, W.; Anelli, J.; Dawson, B.E.

    1974-01-01

    A heat exchanger in which tubes are secured to a tube sheet by internal bore welding is described. The tubes may be moved into place in preparation for welding with comparatively little trouble. A number of segmented tube support plates are provided which allow a considerable portion of each of the tubes to be moved laterally after the end thereof has been positioned in preparation for internal bore welding to the tube sheet. (auth)

  11. Operational Principles for the Dynamics of the In Vitro ParA-ParB System

    PubMed Central

    Jindal, Lavisha; Emberly, Eldon

    2015-01-01

    In many bacteria the ParA-ParB protein system is responsible for actively segregating DNA during replication. ParB proteins move by interacting with DNA bound ParA-ATP, stimulating their unbinding by catalyzing hydrolysis, that leads to rectified motion due to the creation of a wake of depleted ParA. Recent in vitro experiments have shown that a ParB covered magnetic bead can move with constant speed over a DNA covered substrate that is bound by ParA. It has been suggested that the formation of a gradient in ParA leads to diffusion-ratchet like motion of the ParB bead but how it forms and generates a force is still a matter of exploration. Here we develop a deterministic model for the in vitro ParA-ParB system and show that a ParA gradient can spontaneously form due to any amount of initial spatial noise in bound ParA. The speed of the bead is independent of this noise but depends on the ratio of the range of ParA-ParB force on the bead to that of removal of surface bound ParA by ParB. We find that at a particular ratio the speed attains a maximal value. We also consider ParA rebinding (including cooperativity) and ParA surface diffusion independently as mechanisms for ParA recovery on the surface. Depending on whether the DNA covered surface is undersaturated or saturated with ParA, we find that the bead can accelerate persistently or potentially stall. Our model highlights key requirements of the ParA-ParB driving force that are necessary for directed motion in the in vitro system that may provide insight into the in vivo dynamics of the ParA-ParB system. PMID:26670738

  12. Conception et calibration d'un sonoreacteur pour l'oxydation de la cellulose par le systeme TEMPO/NaOCl/NaBr

    NASA Astrophysics Data System (ADS)

    Paquin, Michel

    grande consommation d'energie et de reactif qui rend le procede difficilement accessible au milieu industriel. L'utilisation des ultrasons lors de la reaction d'oxydation permet de reduire de 50% le temps de reaction et d'autant la consommation de produits chimiques. Actuellement le processus d'oxydation s'effectue en mode discontinu pour une quantite de 20 grammes de pate dans un reacteur en verre dans un bain a ultrason. L'objectif principal de ce travail est d'elaborer un sonoreacteur en mode semi-continu afin d'etre en mesure de transferer une reaction d'oxydation du mode discontinu en mode semi-continu. Le transfert de reaction sera effectue en realisant la calibration de l'activite acoustique des deux differents reacteurs, discontinu et semi-continu, par la methode de Weissler. La methode de Weissler quantifie le taux de production radicalaire en mesurant la formation d'iode moleculaire d'une solution aqueuse d'iodure de potassium sous ultrason. Suite a sa calibration, le sonoreacteur pilote (mode semi-continu) a demontre une augmentation de la production radicalaire de 683 % a 170 kHz en comparaison avec l'utilisation d'un bain a ultrason a la meme frequence. Lors de la reaction d'oxydation, la puissance optimale utilisee dans le bain a ultrason a 170 kHz est de 1000 W. La puissance utilisee selon les resultats de calibration obtenue dans le sonoreacteur pilote est de 125 W soit une diminution de l'energie appliquee de 87,5 %. Lors de la reaction d'oxydation, le taux de production des groupements carboxylates est de 2,6 mmol COOH kg/min dans le bain a ultrason et de 6,87 mmol COOH kg/min dans le sonoreacteur pilote soit une augmentation de 164% du taux de formation. Selon les resultats obtenus, l'utilisation d'un sonoreacteur en mode continu peut etre envisageable pour la reaction d'oxydation de la cellulose par le systeme TEMPO-NaOCl-NaBr en industrie au niveau industriel.

  13. Ground-water flow and ground- and surface-water interaction at McBaine Bottoms, Columbia, Missouri--2000-02

    USGS Publications Warehouse

    Smith, Brenda J.

    2003-01-01

    McBaine Bottoms southwest of Columbia, Missouri, is the site of 4,269 acres of the Eagle Bluffs Conservation Area operated by the Missouri Department of Conservation, about 130 acres of the city of Columbia wastewater-treat-ment wetlands, and the city of Columbia munici-pal-supply well field. The city of Columbia wastewater-treatment wetlands supply treated effluent to the Eagle Bluffs Conservation Area. The presence of a sustained ground-water high underlying the Eagle Bluffs Conservation Area has indicated that ground-water flow is toward the municipal well field that supplies drinking water to the city of Columbia. The U.S. Geological Survey, in cooperation with the Missouri Department of Conservation and the city of Columbia, measured the ground-water levels in about 88 monitoring wells and the surface-water elevation at 4 sites monthly during a 27-month period to determine the ground-water flow and the ground- and surface-water interaction at McBaine Bottoms. Lateral ground-water flow was dominated by the presence of a ground-water high that was beneath the Eagle Bluffs Conservation Area and the presence of a cone of depression in the northern part of the study area. The ground-water high was present during all months of the study. Ground-water flow was radially away from the apex of the ground-water high; west and south of the high, flow was toward the Missouri River, east of the high, flow was toward Perche Creek, and north of the high, flow was toward the north toward the city of Columbia well field. The cone of depression was centered around the city of Columbia well field. Another permanent feature on the water-level maps was a ground-water high beneath treatment wetland unit 1. Although the ground-water high beneath the Eagle Bluffs Conservation Area was present throughout the study period, the configuration of the high changed depending on hydrologic conditions. Generally in the spring, the height of the ground-water high began to decrease and hydraulic

  14. Segment-scale and intrasegment lithospheric thickness and melt variations near the Andrew Bain megatransform fault and Marion hot spot: Southwest Indian Ridge, 25.5°E-35°E

    NASA Astrophysics Data System (ADS)

    Takeuchi, Christopher S.; Sclater, John G.; Grindlay, Nancy R.; Madsen, John A.; Rommevaux-Jestin, CéLine

    2010-07-01

    We analyze bathymetric, gravimetric, and magnetic data collected on cruise KN145L16 between 25.5°E and 35°E on the ultraslow spreading Southwest Indian Ridge, where the 750 km long Andrew Bain transform domain separates two accretionary segments to the northeast from a single segment to the southwest. Similar along-axis asymmetries in seafloor texture, rift valley curvature, magnetic anomaly amplitude, magnetization intensity, and mantle Bouguer anomaly (MBA) amplitude within all three segments suggest that a single mechanism may produce variable intrasegment lithospheric thickness and melt delivery. However, closer analysis reveals that a single mechanism is unlikely. In the northeast, MBA lows, shallow axial depths, and large abyssal hills indicate that the Marion hot spot enhances the melt supply to the segments. We argue that along-axis asthenospheric flow from the hot spot, dammed by major transform faults, produces the inferred asymmetries in lithospheric thickness and melt delivery. In the southwest, strong rift valley curvature and nonvolcanic seafloor near the Andrew Bain transform fault indicate very thick subaxial lithosphere at the end of the single segment. We suggest that cold lithosphere adjacent to the eastern end of the ridge axis cools and thickens the subaxial lithosphere, suppresses melt production, and focuses melt to the west. This limits the amount of melt emplaced at shallow levels near the transform fault. Our analysis suggests that the Andrew Bain divides a high melt supply region to the northeast from an intermediate to low melt supply region to the southwest. Thus, this transform fault represents not only a major topographic feature but also a major melt supply boundary on the Southwest Indian Ridge.

  15. Torsion Tests of Tubes

    NASA Technical Reports Server (NTRS)

    Stang, Ambrose H; Ramberg, Walter; Back, Goldie

    1937-01-01

    This report presents the results of tests of 63 chromium-molybdenum steel tubes and 102 17st aluminum-alloy tubes of various sizes and lengths made to study the dependence of the torsional strength on both the dimensions of the tube and the physical properties of the tube material. Three types of failure are found to be important for sizes of tubes frequently used in aircraft construction: (1) failure by plastic shear, in which the tube material reached its yield strength before the critical torque was reached; (2) failure by elastic two-lobe buckling, which depended only on the elastic properties of the tube material and the dimensions of the tube; and (3) failure by a combination of (1) and (2) that is, by buckling taking place after some yielding of the tube material.

  16. Par Pond Fish, Water, and Sediment Chemistry

    SciTech Connect

    Paller, M.H.; Wike, L.D.

    1996-06-01

    The objectives of this report are to describe the Par Pond fish community and the impact of the drawdown and refill on the community, describe contaminant levels in Par Pond fish, sediments, and water and indicate how contaminant concentrations and distributions were affected by the drawdown and refill, and predict possible effects of future water level fluctuations in Par Pond.

  17. Directed and persistent movement arises from mechanochemistry of the ParA/ParB system

    NASA Astrophysics Data System (ADS)

    Hu, Longhua; Vecchiarelli, Anthony G.; Mizuuchi, Kiyoshi; Neuman, Keir C.; Liu, Jian

    The segregation of DNA prior to cell division is essential for faithful genetic inheritance. In many bacteria, segregation of the low-copy-number plasmids involves an active partition system composed of ParA ATPase and its stimulator protein ParB. Recent experiments suggest that ParA/ParB system motility is driven by a diffusion-ratchet mechanism in which ParB-coated plasmid both creates and follows a ParA gradient on the nucleoid surface. However, the detailed mechanism of ParA/ParB-mediated directed and persistent movement remains unknown. We develop a theoretical model describing ParA/ParB-mediated motility. We show that the ParA/ParB system can work as a Brownian ratchet, which effectively couples the ATPase-dependent cycling of ParA-nucleoid affinity to the motion of the ParB bound cargo. Paradoxically, the resulting processive motion relies on quenching diffusive plasmid motion through a large number of transient ParA/ParB-mediated tethers to the nucleoid surface. Our work sheds light on a new emergent phenomenon in which non-motor proteins work collectively via mechanochemical coupling to propel cargos -- an ingenious solution shaped by evolution to cope with the lack of processive motor proteins in bacteria.

  18. Parallel Climate Analysis Toolkit (ParCAT)

    SciTech Connect

    Smith, Brian Edward

    2013-06-30

    The parallel analysis toolkit (ParCAT) provides parallel statistical processing of large climate model simulation datasets. ParCAT provides parallel point-wise average calculations, frequency distributions, sum/differences of two datasets, and difference-of-average and average-of-difference for two datasets for arbitrary subsets of simulation time. ParCAT is a command-line utility that can be easily integrated in scripts or embedded in other application. ParCAT supports CMIP5 post-processed datasets as well as non-CMIP5 post-processed datasets. ParCAT reads and writes standard netCDF files.

  19. suPAR: The Molecular Crystal Ball

    PubMed Central

    Thunø, Maria; Macho, Betina; Eugen-Olsen, Jesper

    2009-01-01

    soluble urokinase Plasminogen Activator Receptor (suPAR) levels reflect inflammation and elevated suPAR levels are found in several infectious diseases and cancer. suPAR exists in three forms; suPARI-III, suPARII-III and suPARI which show different properties due to structural differences. Studies suggest that full-length suPAR is a regulator of uPAR/uPA by acting as uPA-scavenger, whereas the cleaved suPARII-III act as a chemotactic agent promoting the immune response via the SRSRY sequence in the linker-region. This review focus on the various suPAR fragments and their involvement in inflammation and pathogenic processes. We focus on the molecular mechanisms of the suPAR fragments and the link to the inflammatory process, as this could lead to medical applications in infectious and pathological conditions. PMID:19893210

  20. Tracheostomy tube - speaking

    MedlinePlus

    ... this page: //medlineplus.gov/ency/patientinstructions/000465.htm Tracheostomy tube - speaking To use the sharing features on ... are even speaking devices that can help you. Tracheostomy Tubes and Speaking Air passing through vocal cords ( ...

  1. Glass tube splitting tool

    NASA Technical Reports Server (NTRS)

    Klein, J. A.; Murray, C. D.; Stein, J. A.

    1971-01-01

    Tool accurately splits glass tubing so cuts are aligned 180 deg apart and reassembled tube forms low pressure, gastight enclosure. Device should interest industries using cylindrical closed glass containers.

  2. Neural Tube Defects

    MedlinePlus

    Neural tube defects are birth defects of the brain, spine, or spinal cord. They happen in the first month ... she is pregnant. The two most common neural tube defects are spina bifida and anencephaly. In spina ...

  3. Eustachian tube (image)

    MedlinePlus

    ... are more common in children because their eustachian tubes are shorter, narrower, and more horizontal than in ... become trapped when the tissue of the eustachian tube becomes swollen from colds or allergies. Bacteria trapped ...

  4. Feeding tube - infants

    MedlinePlus

    ... tube is misplaced and not in the proper position, the baby may have problems with: An abnormally slow heart rate (bradycardia) Breathing Spitting up Rarely, the feeding tube can puncture the stomach.

  5. Directed and persistent movement arises from mechanochemistry of the ParA/ParB system.

    PubMed

    Hu, Longhua; Vecchiarelli, Anthony G; Mizuuchi, Kiyoshi; Neuman, Keir C; Liu, Jian

    2015-12-22

    The segregation of DNA before cell division is essential for faithful genetic inheritance. In many bacteria, segregation of low-copy number plasmids involves an active partition system composed of a nonspecific DNA-binding ATPase, ParA, and its stimulator protein ParB. The ParA/ParB system drives directed and persistent movement of DNA cargo both in vivo and in vitro. Filament-based models akin to actin/microtubule-driven motility were proposed for plasmid segregation mediated by ParA. Recent experiments challenge this view and suggest that ParA/ParB system motility is driven by a diffusion ratchet mechanism in which ParB-coated plasmid both creates and follows a ParA gradient on the nucleoid surface. However, the detailed mechanism of ParA/ParB-mediated directed and persistent movement remains unknown. Here, we develop a theoretical model describing ParA/ParB-mediated motility. We show that the ParA/ParB system can work as a Brownian ratchet, which effectively couples the ATPase-dependent cycling of ParA-nucleoid affinity to the motion of the ParB-bound cargo. Paradoxically, this resulting processive motion relies on quenching diffusive plasmid motion through a large number of transient ParA/ParB-mediated tethers to the nucleoid surface. Our work thus sheds light on an emergent phenomenon in which nonmotor proteins work collectively via mechanochemical coupling to propel cargos-an ingenious solution shaped by evolution to cope with the lack of processive motor proteins in bacteria.

  6. Directed and persistent movement arises from mechanochemistry of the ParA/ParB system

    PubMed Central

    Hu, Longhua; Vecchiarelli, Anthony G.; Mizuuchi, Kiyoshi; Neuman, Keir C.; Liu, Jian

    2015-01-01

    The segregation of DNA before cell division is essential for faithful genetic inheritance. In many bacteria, segregation of low-copy number plasmids involves an active partition system composed of a nonspecific DNA-binding ATPase, ParA, and its stimulator protein ParB. The ParA/ParB system drives directed and persistent movement of DNA cargo both in vivo and in vitro. Filament-based models akin to actin/microtubule-driven motility were proposed for plasmid segregation mediated by ParA. Recent experiments challenge this view and suggest that ParA/ParB system motility is driven by a diffusion ratchet mechanism in which ParB-coated plasmid both creates and follows a ParA gradient on the nucleoid surface. However, the detailed mechanism of ParA/ParB-mediated directed and persistent movement remains unknown. Here, we develop a theoretical model describing ParA/ParB-mediated motility. We show that the ParA/ParB system can work as a Brownian ratchet, which effectively couples the ATPase-dependent cycling of ParA–nucleoid affinity to the motion of the ParB-bound cargo. Paradoxically, this resulting processive motion relies on quenching diffusive plasmid motion through a large number of transient ParA/ParB-mediated tethers to the nucleoid surface. Our work thus sheds light on an emergent phenomenon in which nonmotor proteins work collectively via mechanochemical coupling to propel cargos—an ingenious solution shaped by evolution to cope with the lack of processive motor proteins in bacteria. PMID:26647183

  7. Microhole Tubing Bending Report

    DOE Data Explorer

    Oglesby, Ken

    2012-01-01

    A downhole tubing bending study was made and is reported herein. IT contains a report and 2 excel spreadsheets to calculate tubing bending and to estimate contact points of the tubing to the drilled hole wall (creating a new support point).

  8. 21 CFR 868.5800 - Tracheostomy tube and tube cuff.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Tracheostomy tube and tube cuff. 868.5800 Section... (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5800 Tracheostomy tube and tube cuff. (a) Identification. A tracheostomy tube and tube cuff is a device intended to be placed into...

  9. 21 CFR 868.5800 - Tracheostomy tube and tube cuff.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tracheostomy tube and tube cuff. 868.5800 Section... (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5800 Tracheostomy tube and tube cuff. (a) Identification. A tracheostomy tube and tube cuff is a device intended to be placed into...

  10. 21 CFR 868.5800 - Tracheostomy tube and tube cuff.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Tracheostomy tube and tube cuff. 868.5800 Section... (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5800 Tracheostomy tube and tube cuff. (a) Identification. A tracheostomy tube and tube cuff is a device intended to be placed into...

  11. 21 CFR 868.5800 - Tracheostomy tube and tube cuff.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Tracheostomy tube and tube cuff. 868.5800 Section... (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5800 Tracheostomy tube and tube cuff. (a) Identification. A tracheostomy tube and tube cuff is a device intended to be placed into...

  12. 21 CFR 868.5800 - Tracheostomy tube and tube cuff.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Tracheostomy tube and tube cuff. 868.5800 Section... (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5800 Tracheostomy tube and tube cuff. (a) Identification. A tracheostomy tube and tube cuff is a device intended to be placed into...

  13. REACTOR COOLANT TUBE SEAL

    DOEpatents

    Morris, W.J.

    1958-12-01

    A plle-flattenlng control element and a fluid seal therefore to permit movement of the element into a liquld contnining region of a neutronlc reactor are described. The device consists of flattened, thin-walled aluminum tubing contalnlng a uniform mixture of thermal neutron absorbing material, and a number of soft rubber closures for the process tubes, having silts capable of passing the flattened elements therethrough, but effectively sealing the process tubes against fluld leaknge by compression of the rubber. The flattened tubing is sufficiently flexible to enable it to conform to the configuratlon of the annular spacing surrounding the fuel elements ln the process tubes.

  14. Protease-activated receptor-1 (PAR1) and PAR2 but not PAR4 mediate relaxations in lower esophageal sphincter.

    PubMed

    Huang, Shih-Che

    2007-07-01

    Protease-activated receptor-1 (PAR1), PAR2 and PAR4 activation can alter the gastrointestinal motility. To investigate effects mediated by PARs in the lower esophageal sphincter, we measured contraction or relaxation of transverse strips from the guinea-pig lower esophageal sphincter caused by PAR1 (TFLLR-NH2 and SFLLRN-NH2), PAR2 (SLIGKV-NH2 and SLIGRL-NH2) and PAR4 peptide agonists (GYPGKF-NH2, GYPGQV-NH2 and AYPGKF-NH2) as well as PAR protease activators (thrombin and trypsin). In resting lower esophageal sphincter strips, TFLLR-NH2 and SFLLRN-NH2 caused moderate concentration-dependent relaxation whereas thrombin did not cause any relaxation or contraction. Furthermore, in carbachol-contracted strips, TFLLR-NH2 and SFLLRN-NH2 caused marked whereas thrombin caused mild concentration-dependent relaxation. These indicate the existence of PAR1 mediating relaxation. Similarly, in resting lower esophageal sphincter strips, trypsin caused moderate concentration-dependent relaxation whereas SLIGRL-NH2 and SLIGKV-NH2 did not cause any relaxation or contraction. In addition, in carbachol-contracted strips, trypsin caused marked whereas SLIGRL-NH2 and SLIGKV-NH2 caused mild concentration-dependent relaxation. These indicate the existence of PAR2 mediating relaxation. The relaxant response of thrombin, TFLLR-NH2, trypsin and SLIGKV-NH2 was insensitive to atropine or tetrodotoxin, suggesting a direct effect. The relaxant response of trypsin was not affected by apamin, charybdotoxin, indomethacin and capsaicin but was attenuated by NG-nitro-L-arginine methyl ester, indicating involvement of NO. FSLLR-NH2, a PAR1 control peptide, and VKGILS-NH2, a PAR2 control peptide, as well as all three PAR4 peptide agonists, GYPGKF-NH2, GYPGQV-NH2 and AYPGKF-NH2, did not cause any relaxation or contraction. Taken together, these results demonstrate that PAR1 and PAR2 but not PAR4 mediate relaxations in the guinea-pig lower esophageal sphincter. PMID:17335921

  15. Intercostal drainage tube or intracardiac drainage tube?

    PubMed Central

    Anitha, N.; Kamath, S. Ganesh; Khymdeit, Edison; Prabhu, Manjunath

    2016-01-01

    Although insertion of chest drain tubes is a common medical practice, there are risks associated with this procedure, especially when inexperienced physicians perform it. Wrong insertion of the tube has been known to cause morbidity and occasional mortality. We report a case where the left ventricle was accidentally punctured leading to near-exsanguination. This report is to highlight the need for experienced physicians to supervise the procedure and train the younger physician in the safe performance of the procedure. PMID:27397467

  16. NEI You Tube Videos: Amblyopia

    MedlinePlus

    ... YouTube Videos > NEI YouTube Videos: Amblyopia NEI YouTube Videos YouTube Videos Home Age-Related Macular Degeneration Amblyopia ... of Prematurity Science Spanish Videos Webinars NEI YouTube Videos: Amblyopia NEI on Twitter NEI on YouTube NEI ...

  17. Lunar Lava Tube Sensing

    NASA Technical Reports Server (NTRS)

    York, Cheryl Lynn; Walden, Bryce; Billings, Thomas L.; Reeder, P. Douglas

    1992-01-01

    Large (greater than 300 m diameter) lava tube caverns appear to exist on the Moon and could provide substantial safety and cost benefits for lunar bases. Over 40 m of basalt and regolith constitute the lava tube roof and would protect both construction and operations. Constant temperatures of -20 C reduce thermal stress on structures and machines. Base designs need not incorporate heavy shielding, so lightweight materials can be used and construction can be expedited. Identification and characterization of lava tube caverns can be incorporated into current precursor lunar mission plans. Some searches can even be done from Earth. Specific recommendations for lunar lava tube search and exploration are (1) an Earth-based radar interferometer, (2) an Earth-penetrating radar (EPR) orbiter, (3) kinetic penetrators for lunar lava tube confirmation, (4) a 'Moon Bat' hovering rocket vehicle, and (5) the use of other proposed landers and orbiters to help find lunar lava tubes.

  18. PAR for the Course: A Congruent Pedagogical Approach for a PAR Methods Class

    ERIC Educational Resources Information Center

    Hammond, Joyce D.; Hicks, Maria; Kalman, Rowenn; Miller, Jason

    2005-01-01

    In the past two years, three graduate students and a senior faculty member have co-taught a participatory action research (PAR) course to undergraduate and graduate students. In this article the co-teachers advocate a set of pedagogical principles and practices in a PAR-oriented classroom that establishes congruency with community PAR projects in…

  19. Ruggedized electronographic tube development

    NASA Technical Reports Server (NTRS)

    Nevin, S.

    1981-01-01

    Because of their glass components and lack of far ultraviolet sensitivity, currently available Spectracons are not suited for rocket launch. Technology developed for second generation image tubes and for magnetically focused image tubes can be applied to improve the optical and mechanical properties of these magnetically focused electronographic tubes whose 40 kilovolt signal electrons exit a 4-micrometer thick mica window and penetrate a photographic recording emulsion.

  20. Conduction cooled tube supports

    DOEpatents

    Worley, Arthur C.; Becht, IV, Charles

    1984-01-01

    In boilers, process tubes are suspended by means of support studs that are in thermal contact with and attached to the metal roof casing of the boiler and the upper bend portions of the process tubes. The support studs are sufficiently short that when the boiler is in use, the support studs are cooled by conduction of heat to the process tubes and the roof casing thereby maintaining the temperature of the stud so that it does not exceed 1400.degree. F.

  1. TUBE SPLITTING APPARATUS

    DOEpatents

    Frantz, C.E.; Cawley, W.E.

    1961-05-01

    A tool is described for cutting a coolant tube adapted to contain fuel elements to enable the tube to be removed from a graphite moderator mass. The tool splits the tube longitudinally into halves and curls the longitudinal edges of the halves inwardly so that they occupy less space and can be moved radially inwardly away from the walls of the hole in the graphite for easy removal from the graphite.

  2. COAXIAL TUBE COUPLING

    DOEpatents

    Niemoth, H.R.

    1963-02-26

    BS>This patent shows a device for quickly coupling coaxial tubes in metal-to-metal fashion, so as to be suitable for use in a nuclear reactor. A threaded coliar urges a tapered metal extension on the outer coaxial tube into a tapered seat in the device and simultaneously exerts pressure through a coaxial helical spring so that a similar extension on the inner tube seats in a similar seat near the other end. (AEC)

  3. Wound tube heat exchanger

    DOEpatents

    Ecker, Amir L.

    1983-01-01

    What is disclosed is a wound tube heat exchanger in which a plurality of tubes having flattened areas are held contiguous adjacent flattened areas of tubes by a plurality of windings to give a double walled heat exchanger. The plurality of windings serve as a plurality of effective force vectors holding the conduits contiguous heat conducting walls of another conduit and result in highly efficient heat transfer. The resulting heat exchange bundle is economical and can be coiled into the desired shape. Also disclosed are specific embodiments such as the one in which the tubes are expanded against their windings after being coiled to insure highly efficient heat transfer.

  4. Flared tube attachment fitting

    NASA Technical Reports Server (NTRS)

    Alkire, I. D.; King, J. P., Jr.

    1980-01-01

    Tubes can be flared first, then attached to valves and other flow line components, with new fitting that can be disassembled and reused. Installed fitting can be disassembled so parts can be inspected. It can be salvaged and reused without damaging flared tube; tube can be coated, tempered, or otherwise treated after it has been flared, rather than before, as was previously required. Fitting consists of threaded male portion with conical seating surface, hexagonal nut with hole larger than other diameter of flared end of tube, and split ferrule.

  5. Composite Pulse Tube

    NASA Technical Reports Server (NTRS)

    Martin, Jerry L.; Cloyd, Jason H.

    2007-01-01

    A modification of the design of the pulse tube in a pulse-tube cryocooler reduces axial thermal conductance while preserving radial thermal conductance. It is desirable to minimize axial thermal conductance in the pulse-tube wall to minimize leakage of heat between the warm and cold ends of the pulse tube. At the same time, it is desirable to maximize radial thermal conductance at the cold end of the pulse tube to ensure adequate thermal contact between (1) a heat exchanger in the form of a stack of copper screens inside the pulse tube at the cold end and (2) the remainder of the cold tip, which is the object to which the heat load is applied and from which heat must be removed. The modified design yields a low-heat-leak pulse tube that can be easily integrated with a cold tip. A typical pulse tube of prior design is either a thin-walled metal tube or a metal tube with a nonmetallic lining. It is desirable that the outer surface of a pulse tube be cylindrical (in contradistinction to tapered) to simplify the design of a regenerator that is also part of the cryocooler. Under some conditions, it is desirable to taper the inner surface of the pulse tube to reduce acoustic streaming. The combination of a cylindrical outer surface and a tapered inner surface can lead to unacceptably large axial conduction if the pulse tube is made entirely of metal. Making the pulse-tube wall of a nonmetallic, lowthermal- conductivity material would not solve the problem because the wall would not afford the needed thermal contact for the stack of screens in the cold end. The modified design calls for fabricating the pulse tube in two parts: a longer, nonmetallic part that is tapered on the inside and cylindrical on the outside and a shorter, metallic part that is cylindrical on both the inside and the outside. The nonmetallic part can be made from G-10 fiberglass-reinforced epoxy or other low-thermal-conductivity, cryogenically compatible material. The metallic part must have high

  6. Sapphire tube pressure vessel

    DOEpatents

    Outwater, John O.

    2000-01-01

    A pressure vessel is provided for observing corrosive fluids at high temperatures and pressures. A transparent Teflon bag contains the corrosive fluid and provides an inert barrier. The Teflon bag is placed within a sapphire tube, which forms a pressure boundary. The tube is received within a pipe including a viewing window. The combination of the Teflon bag, sapphire tube and pipe provides a strong and inert pressure vessel. In an alternative embodiment, tie rods connect together compression fittings at opposite ends of the sapphire tube.

  7. Par Pond vegetation status Summer 1995 -- Summary

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1996-01-01

    The water level of Par Pond was lowered approximately 20 feet in mid-1991 in order to protect downstream residents from possible dam failure suggested by subsidence on the downstream slope of the dam and to repair the dam. This lowering exposed both emergent and nonemergent macrophyte beds to drying conditions resulting in extensive losses. A survey of the newly emergent, shoreline aquatic plant communities of Par Pond began in June 1995, three months after the refilling of Par Pond to approximately 200 feet above mean sea level. These surveys continued in July, September, and late October, 1995. Communities similar to the pre-drawdown, Par Pond aquatic plant communities are becoming re-established. Emergent beds of maidencane, lotus, waterlily, and watershield are extensive and well developed. Cattail occurrence continued to increase during the summer, but large beds common to Par Pond prior to the drawdown have not formed. Estimates from SPOT HRV, remote sensing satellite data indicated that as much as 120 hectares of emergent wetlands vegetation may have been present along the Par Pond shoreline by early October, 1995. To track the continued development of macrophytes in Par Pond, future surveys throughout 1996 and 1997, along with the continued evaluation of satellite data to map the areal extent of the macrophyte beds of Par Pond, are planned.

  8. Steam generator tube failures

    SciTech Connect

    MacDonald, P.E.; Shah, V.N.; Ward, L.W.; Ellison, P.G.

    1996-04-01

    A review and summary of the available information on steam generator tubing failures and the impact of these failures on plant safety is presented. The following topics are covered: pressurized water reactor (PWR), Canadian deuterium uranium (CANDU) reactor, and Russian water moderated, water cooled energy reactor (VVER) steam generator degradation, PWR steam generator tube ruptures, the thermal-hydraulic response of a PWR plant with a faulted steam generator, the risk significance of steam generator tube rupture accidents, tubing inspection requirements and fitness-for-service criteria in various countries, and defect detection reliability and sizing accuracy. A significant number of steam generator tubes are defective and are removed from service or repaired each year. This wide spread damage has been caused by many diverse degradation mechanisms, some of which are difficult to detect and predict. In addition, spontaneous tube ruptures have occurred at the rate of about one every 2 years over the last 20 years, and incipient tube ruptures (tube failures usually identified with leak detection monitors just before rupture) have been occurring at the rate of about one per year. These ruptures have caused complex plant transients which have not always been easy for the reactor operators to control. Our analysis shows that if more than 15 tubes rupture during a main steam line break, the system response could lead to core melting. Although spontaneous and induced steam generator tube ruptures are small contributors to the total core damage frequency calculated in probabilistic risk assessments, they are risk significant because the radionuclides are likely to bypass the reactor containment building. The frequency of steam generator tube ruptures can be significantly reduced through appropriate and timely inspections and repairs or removal from service.

  9. Method for shaping polyethylene tubing

    NASA Technical Reports Server (NTRS)

    Kramer, R. C.

    1981-01-01

    Method forms polyethylene plastic tubing into configurations previously only possible with metal tubing. By using polyethylene in place of copper or stain less steel tubing inlow pressure systems, fabrication costs are significantly reduced. Polyethylene tubing can be used whenever low pressure tubing is needed in oil operations, aircraft and space applications, powerplants, and testing laboratories.

  10. Gastrostomy feeding tube - pump - child

    MedlinePlus

    Feeding - gastrostomy tube - pump; G-tube - pump; Gastrostomy button - pump; Bard Button - pump; MIC-KEY - pump ... Your child has a gastrostomy tube (G-tube). This is a soft, plastic tube placed into your child's stomach. It delivers nutrition (food) and medicines until your ...

  11. Hologram recording tubes

    NASA Technical Reports Server (NTRS)

    Rajchman, J. H.

    1973-01-01

    Optical memories allow extremely large numbers of bits to be stored and recalled in a matter of microseconds. Two recording tubes, similar to conventional image-converting tubes, but having a soft-glass surface on which hologram is recorded, do not degrade under repeated hologram read/write cycles.

  12. ParAB Partition Dynamics in Firmicutes: Nucleoid Bound ParA Captures and Tethers ParB-Plasmid Complexes

    PubMed Central

    Lioy, Virginia S.; Volante, Andrea; Soberón, Nora E.; Lurz, Rudi; Ayora, Silvia; Alonso, Juan C.

    2015-01-01

    In Firmicutes, small homodimeric ParA-like (δ2) and ParB-like (ω2) proteins, in concert with cis-acting plasmid-borne parS and the host chromosome, secure stable plasmid inheritance in a growing bacterial population. This study shows that (ω:YFP)2 binding to parS facilitates plasmid clustering in the cytosol. (δ:GFP)2 requires ATP binding but not hydrolysis to localize onto the cell’s nucleoid as a fluorescent cloud. The interaction of (δ:CFP)2 or δ2 bound to the nucleoid with (ω:YFP)2 foci facilitates plasmid capture, from a very broad distribution, towards the nucleoid and plasmid pairing. parS-bound ω2 promotes redistribution of (δ:GFP)2, leading to the dynamic release of (δ:GFP)2 from the nucleoid, in a process favored by ATP hydrolysis and protein-protein interaction. (δD60A:GFP)2, which binds but cannot hydrolyze ATP, also forms unstable complexes on the nucleoid. In the presence of ω2, (δD60A:GFP)2 accumulates foci or patched structures on the nucleoid. We propose that (δ:GFP)2 binding to different nucleoid regions and to ω2-parS might generate (δ:GFP)2 gradients that could direct plasmid movement. The iterative pairing and unpairing cycles may tether plasmids equidistantly on the nucleoid to ensure faithful plasmid segregation by a mechanism compatible with the diffusion-ratchet mechanism as proposed from in vitro reconstituted systems. PMID:26161642

  13. Fallopian Tube Catheterization

    PubMed Central

    Thurmond, Amy Suzanne

    2013-01-01

    Fallopian tube catheterization is used for treatment of infertility caused by proximal tubal occlusion, and has replaced surgical treatment for this condition. More recently, fallopian tube catheterization has been used for tubal sterilization. Interventional radiologists tested numerous methods for tubal occlusion using the rabbit as an animal model. As a result, a tubal device has recently been Food and Drug Administration approved for permanent sterilization using hysteroscopic guidance; it can also be placed fluoroscopically by fallopian tube catheterization as an “off-label” procedure. This is a 5-year continuation and update on a procedure that has been done by interventional radiologists for 25 years; history of the development of fallopian tube catheterization in women has been published in detail in this journal. Highlighted in this article will be description of the basic components needed for fallopian tube catheterization. PMID:24436565

  14. Robotic Tube-Gap Inspector

    NASA Technical Reports Server (NTRS)

    Gilbert, Jeffrey L.; Gutow, David A.; Maslakowski, John E.

    1993-01-01

    Robotic vision system measures small gaps between nearly parallel tubes. Robot-held video camera examines closely spaced tubes while computer determines gaps between tubes. Video monitor simultaneously displays data on gaps.

  15. What Are Neural Tube Defects?

    MedlinePlus

    ... NICHD Research Information Clinical Trials Resources and Publications Neural Tube Defects (NTDs): Condition Information Skip sharing on ... media links Share this: Page Content What are neural tube defects? Neural (pronounced NOOR-uhl ) tube defects ...

  16. [Enteral tube feeding].

    PubMed

    Haller, Alois

    2014-03-01

    Tube feeding is an integral part of medical therapies, and can be easily managed also in the outpatient setting. Tube feeding by the stomach or small intestine with nasogastral or nasojejunal tubes is common in clinical practice. Long-term nutrition is usually provided through a permanent tube, i. e. a percutaneous endoscopic gastrostomy (PEG). Modern portable nutrition pumps are used to cover the patient's nutritional needs. Enteral nutrition is always indicated if patients can not or should not eat or if nutritional requirements cannot be covered within 3 days after an intervention, e. g. after abdominal surgery. Industrially produced tube feedings with defined substrate concentrations are being used; different compositions of nutrients, such as glutamine fish oil etc., are used dependent on the the condition of the patient. Enteral nutrition may be associated with complications of the tube, e. g. dislocation, malposition or obstruction, as well as the feeding itself, e. g.hyperglycaemia, electrolyte disturbances, refeeding syndrome diarrhea or aspiration). However, the benefit of tube feeding usually exceeds the potential harm substantially.

  17. Eustachian Tube Function.

    PubMed

    Ars, Bernard; Dirckx, Joris

    2016-10-01

    The fibrocartilaginous eustachian tube is part of a system of contiguous organs including the nose, palate, rhinopharynx, and middle ear cleft. The middle ear cleft consists of the tympanic cavity, which includes the bony eustachian tube (protympanum) and the mastoid gas cells system. The tympanic cavity and mastoid gas cells are interconnected and allow gaseous exchange and pressure regulation. The fibrocartilaginous eustachian tube is a complex organ consisting of a dynamic conduit with its mucosa, cartilage, surrounding soft tissue, peritubal muscles (ie, tensor and levator veli palatine, salpingopharyngeus and tensor tympani), and superior bony support (the sphenoid sulcus). PMID:27468632

  18. Tube flare inspection tool

    NASA Technical Reports Server (NTRS)

    Meunier, G. E.

    1980-01-01

    Flare angle and symmetry of tube ends can be checked by simple tool that consists of two stainless steel pins bonded to rubber plug. Primary function of tool is to inspect tubes before they are installed, thereby eliminating expense and inconvenience of repairing leaks caused by imperfect flares. Measuring hole tapers, countersink angles, and bearing race angles are other possible uses. Tool is used with optical comparator. Axis of tool is alined with centerline of tube. Shadow of seated pins on comparator screen allows operator to verify flare angle is within tolerance.

  19. Comparative cactus architecture and par interception

    SciTech Connect

    Geller, G.N.; Nobel, P.S. )

    1987-07-01

    Because CO{sup 2} uptake by cacti can be limited by low levels of photosynthetically active radiation (PAR) and because plant form affects PAR interception, various cactus forms were studied using a computer model, field measurements, and laboratory phototropic studies. Model predictions indicated that CO{sub 2} uptake by individual stems at an equinox was greatest when the stem were vertical, but at the summer and the winter solstice CO{sub 2} uptake was greatest for stems titled 30{degree} away from the equator. Stem tilting depended on form and taxonomic group. Not only can the shape of cacti be affected by PAR, but also shape influences PAR interception and hence CO{sub 2} uptake.

  20. Tube Alinement for Machining

    NASA Technical Reports Server (NTRS)

    Garcia, J.

    1984-01-01

    Tool with stepped shoulders alines tubes for machining in preparation for welding. Alinement with machine tool axis accurate to within 5 mils (0.13mm) and completed much faster than visual setup by machinist.

  1. Kinking of medical tubes.

    PubMed

    Ingles, David

    2004-05-01

    The phenomenon of kinking in medical tubing remains a problem for some applications, particularly critical ones such as transporting gasses or fluids. Design features are described to prevent its occurrence.

  2. Ear tube insertion - slideshow

    MedlinePlus

    ... this page: //medlineplus.gov/ency/presentations/100045.htm Ear tube insertion - series—Normal anatomy To use the ... 4 Overview The eardrum (tympanic membrane) separates the ear canal from the middle ear. Update Date 8/ ...

  3. Tracheostomy tube - eating

    MedlinePlus

    Trach - eating ... take your first bites. Certain factors may make eating or swallowing harder, such as: Changes in the ... easier to swallow. Suction the tracheostomy tube before eating. This will keep you from coughing while eating, ...

  4. Tube-Forming Assays.

    PubMed

    Brown, Ryan M; Meah, Christopher J; Heath, Victoria L; Styles, Iain B; Bicknell, Roy

    2016-01-01

    Angiogenesis involves the generation of new blood vessels from the existing vasculature and is dependent on many growth factors and signaling events. In vivo angiogenesis is dynamic and complex, meaning assays are commonly utilized to explore specific targets for research into this area. Tube-forming assays offer an excellent overview of the molecular processes in angiogenesis. The Matrigel tube forming assay is a simple-to-implement but powerful tool for identifying biomolecules involved in angiogenesis. A detailed experimental protocol on the implementation of the assay is described in conjunction with an in-depth review of methods that can be applied to the analysis of the tube formation. In addition, an ImageJ plug-in is presented which allows automatic quantification of tube images reducing analysis times while removing user bias and subjectivity.

  5. Building with Tubes.

    ERIC Educational Resources Information Center

    D'Eugenio, Terrance, Ed.

    Text and illustrations show how to assemble furniture and toys out of cardboard tubes and sheets. Basic directions are provided, and the tools and materials necessary to the assembly of specific items are described. (MLF)

  6. Using a nasogastric tube.

    PubMed

    Candy, C

    1986-09-01

    This discussion of the use of a nasogastric tube covers the equipment needed, the method, rehydration and feeding, prolonged nasogastric feeding, and stopping nasogastric feeding. A nasogastric tube is useful when children are unable to drink safely and in sufficient amounts for any of the following reasons: severe dehydration; if intravenous (IV) therapy is unavailable; low birth weight infants; or the child is drowsy or vomiting. Severely malnourished children may be fed initially in this way if they are too weak or anorexic to eat or drink normally. The following equipment is needed: nasogastric tube; lubricating fluid; a syringe; blue litmus paper, if available; adhesive tape; stethoscope if available; and fluid to be given. Explain to the child's parents and the child, if old enough to understand, what will be done; lie infants flat; measure the approximate length from the child's nostril to the ear lobe and then to the top of the abdomen with the tube and mark the position; clean the nostrils to remove the mucus, and lubricate the tip of the tube and gently insert into the nostril; give the child a drink of water if he or she is conscious; continue to pass the tube down until the position marked reaches the nostril; use the syringe to suck up some fluid and test with blue litmus paper to check that the tube is in the stomach; and inject 5-10 ml of fluid (saline or oral rehydration solution, not milk formula) by syringe if satisfied the tube is in the correct position. Where possible, give a continuous drip of fluid. If this is not possible, give frequent small amounts using the syringe as a funnel. If feeding continues for more than 24 hours, clean the nostrils daily with warm water and change the tube to the other nostril every few days. Also keep the mouth very clean with a dilute solution of 8% sodium bicarbonate, if available, or citrus fruit juice. To remove the tube, remove the adhesive tape, take the tube out gently and smoothly, and offer the child a

  7. Tubing crimping pliers

    DOEpatents

    Lindholm, G.T.

    1981-02-27

    The disclosure relates to pliers and more particularly to pliers for crimping two or more pieces of copper tubing together prior to their being permanently joined by brazing, soldering or the like. A die containing spring-loaded pins rotates within a cammed ring in the head of the pliers. As the die rotates, the pins force a crimp on tubing held within the pliers.

  8. Scleral fixation of Ahmed glaucoma valve tube tip for adjustment of cornea-touching malposition

    PubMed Central

    Ma, K T; Kim, J H; Seong, G J; Jang, D S; Kim, C Y

    2014-01-01

    Purpose Tube-corneal touch occurring after Ahmed glaucoma valve (AGV) implantation is conventionally treated by tube cutting or tube transposition from the original pathway. However, in some cases, tube cutting is insufficient, and rearranging the pathway of the tube through a new sclera tunnel, ciliary sulcus, or pars plana is not feasible, as the conjunctiva and sclera covering the tube are difficult to be redissected. So, we propose a novel technique that repositions malpositioned AGV tube using scleral fixation and its successful applications in two patients with tube-corneal touch. Methods (A) A scleral flap is made at the point for scleral fixation. (B) The anterior chamber is maintained using an anterior chamber maintainer. The incision is made immediately above the tube entering the anterior chamber and the tube end is flipped out using a Sinskey. (C) A double-armed 10/0 prolene straight needle is penetrated through the tube end. The leading needle enters the anterior chamber through the previously made incision and is pulled through the scleral flap. (D) The tube tip and the second needle of the double-armed 10/0 prolene straight needle also enter the anterior chamber through the previously made incision and the second needle is pulled through the scleral flap. The tube end is extended to be parallel to the cornea surface. Results Patients maintained good tube positioning without any serious complications during average of 15 months of follow-up after operation. Conclusion We believe that our method is a simple and minimally invasive surgical method for treating AGV tube touching of the corneal endothelium. However, considering the limited number of cases studied and the short follow-up period, a larger group with a longer follow-up period is necessary. PMID:24097119

  9. Aeronautical tubes and pipes

    NASA Astrophysics Data System (ADS)

    Beauclair, N.

    1984-12-01

    The main and subcomponent French suppliers of aircraft tubes and pipes are discussed, and the state of the industry is analyzed. Quality control is essential for tubes with regard to their i.d. and metallurgical compositions. French regulations do not allow welded seam tubes in hydraulic circuits unless no other form is available, and then rustproofed steel must be installed. The actual low level of orders for any run of tubes dictates that the product is only one of several among the manufacturers' line. Automation, both in NDT and quality control, assures that the tubes meet specifications. A total of 10 French companies participate in the industry, serving both civil and military needs, with some companies specializing only in titanium, steel, or aluminum materials. Concerns wishing to enter the market must upgrade their equipment to meet the higher aeronautical specifications and be prepared to furnish tubes and pipes that serve both functional and structural purposes simultaneously. Additionally, pipe-bending machines must also perform to tight specifications. Pipes can range from 0.2 mm exterior diameter to 40 mm, with wall thicknesses from 0.02 mm to 3 mm. A chart containing a list of manufacturers and their respective specifications and characteristics is presented, and a downtrend in production with reduction of personnel is noted.

  10. Clearing obstructed feeding tubes.

    PubMed

    Marcuard, S P; Stegall, K L; Trogdon, S

    1989-01-01

    This is a report of an in vitro study evaluating the ability of six solutions to dissolve clotted enteral feeding, which can cause feeding tube occlusion. The following clotted enteral feeding products were tested: Ensure Plus, Ensure Plus with added protein (Promod 20 g/liter), Osmolite, Enrich, and Pulmocare. Clot dissolution was then tested by adding Adolf's Meat Tenderizer, Viokase, Sprite, Pepsi, Coke, or Mountain Dew. Distilled water served as control. Dissolution score for each mixture was assessed blindly. Best dissolution was observed with Viokase in pH 7.9 solution (p less than 0.01). Similar results were obtained when feeding tube patency was restored in eight in vitro occluded feeding tubes (Dobbhoff, French size 8) by using first Pepsi (two/eight successful) and then Viokase in pH 7.9 (six/six successful). We also report our experience in the first 10 patients with occluded feeding tubes using this Viokase solution injected through a Drum catheter into the feeding tube. In seven patients, this method proved to be successful, and the reasons for failure in three patients include a knotted tube, impacted tablet powder, and a formula clot fo 24 hr duration and 45 cm in length. PMID:2494372

  11. Clearing obstructed feeding tubes.

    PubMed

    Marcuard, S P; Stegall, K L; Trogdon, S

    1989-01-01

    This is a report of an in vitro study evaluating the ability of six solutions to dissolve clotted enteral feeding, which can cause feeding tube occlusion. The following clotted enteral feeding products were tested: Ensure Plus, Ensure Plus with added protein (Promod 20 g/liter), Osmolite, Enrich, and Pulmocare. Clot dissolution was then tested by adding Adolf's Meat Tenderizer, Viokase, Sprite, Pepsi, Coke, or Mountain Dew. Distilled water served as control. Dissolution score for each mixture was assessed blindly. Best dissolution was observed with Viokase in pH 7.9 solution (p less than 0.01). Similar results were obtained when feeding tube patency was restored in eight in vitro occluded feeding tubes (Dobbhoff, French size 8) by using first Pepsi (two/eight successful) and then Viokase in pH 7.9 (six/six successful). We also report our experience in the first 10 patients with occluded feeding tubes using this Viokase solution injected through a Drum catheter into the feeding tube. In seven patients, this method proved to be successful, and the reasons for failure in three patients include a knotted tube, impacted tablet powder, and a formula clot fo 24 hr duration and 45 cm in length.

  12. Polycystin-1 binds Par3/aPKC and controls convergent extension during renal tubular morphogenesis.

    PubMed

    Castelli, Maddalena; Boca, Manila; Chiaravalli, Marco; Ramalingam, Harini; Rowe, Isaline; Distefano, Gianfranco; Carroll, Thomas; Boletta, Alessandra

    2013-01-01

    Several organs, including the lungs and kidneys, are formed by epithelial tubes whose proper morphogenesis ensures correct function. This is best exemplified by the kidney, where defective establishment or maintenance of tubular diameter results in polycystic kidney disease, a common genetic disorder. Most polycystic kidney disease cases result from loss-of-function mutations in the PKD1 gene, encoding Polycystin-1, a large receptor of unknown function. Here we demonstrate that PC-1 has an essential role in the establishment of correct tubular diameter during nephron development. Polycystin-1 associates with Par3 favouring the assembly of a pro-polarizing Par3/aPKC complex and it regulates a programme of cell polarity important for oriented cell migration and for a convergent extension-like process during tubular morphogenesis. Par3 inactivation in the developing kidney results in defective convergent extension and tubular morphogenesis, and in renal cyst formation. Our data define Polycystin-1 as central to cell polarization and to epithelial tube morphogenesis and homeostasis. PMID:24153433

  13. Proteinase-activated receptor-1 (PAR(1)) and PAR(2) but not PAR(4) mediate contraction in human and guinea-pig gallbladders.

    PubMed

    Lee, M-C; Huang, S-C

    2008-04-01

    Proteinase-activated receptor-1 (PAR(1)) and PAR(2) mediate contraction in the guinea-pig gallbladder. To investigate and compare the effects mediated by PARs in the human gallbladder with those in the guinea-pig gallbladder, we measured contractions of isolated human and guinea-pig gallbladder strips caused by PAR agonists. Results in human were similar to those in guinea-pig gallbladder. The PAR(1) agonists, thrombin, TFLLR-NH2 and SFLLRN-NH2, as well as the PAR(2) agonists, trypsin, SLIGKV-NH2 and SLIGRL-NH2, caused contraction in both human and guinea-pig gallbladders. These indicate the existence of PAR(1) and PAR(2) mediating gallbladder contraction. Furthermore, the existence of PAR(1) and PAR(2) in the human gallbladder was confirmed by reverse transcription-polymerase chain reaction. In contrast, FSLLR-NH2, a PAR(1) control peptide, and VKGILS-NH2, a PAR(2) control peptide, as well as three PAR(4) agonists, GYPGKF-NH2, GYPGQV-NH2 and AYPGKF-NH2, did not cause any contraction or relaxation. The contractile responses to TFLLR-NH2, SFLLRN-NH2 and trypsin in both human and guinea-pig gallbladders were insensitive to atropine and tetrodotoxin, suggesting direct effects. These results demonstrate that, similar to the guinea-pig gallbladder, both PAR(1) and PAR(2) but not PAR(4) mediate muscle contraction in the human gallbladder. PAR(1) and PAR(2) may play important roles in the control of both human and guinea-pig gallbladder motility. PMID:18179608

  14. Proteinase-activated receptor-1 (PAR1) and PAR2 mediate relaxation of guinea pig internal anal sphincter.

    PubMed

    Huang, Shih-Che

    2014-02-10

    Activation of proteinase-activated receptor-1 (PAR1) and PAR2 stimulates contraction of the rat but relaxation of the guinea pig colon. The aim of the present study was to investigate PAR effects on internal anal sphincter (IAS) motility. We measured relaxation of isolated muscle strips from the guinea pig IAS caused by PAR agonists using isometric transducers. Reverse transcription polymerase chain reaction (RT-PCR) was performed to determine the existence of PAR. In the IAS, thrombin and PAR1 peptide agonists TFLLR-NH2 and SFLLRN-NH2 evoked moderate to marked relaxation in a concentration-dependent manner. In addition, trypsin and PAR2 peptide agonists 2-furoyl-LIGRLO-NH2, SLIGRL-NH2 and SLIGKV-NH2 produced relaxation. In contrast, both PAR1 and PAR2 inactive control peptides did not elicit relaxation. Furthermore, the selective PAR1 antagonist vorapaxar and PAR2 antagonist GB 83 specifically inhibited thrombin and trypsin-induced relaxations, respectively. RT-PCR revealed the presence of PAR1 and PAR2 in the IAS. This indicates that PAR1 and PAR2 mediate the IAS relaxation. The relaxant responses of TFLLR-NH2 and trypsin were attenuated by N(omega)-Nitro-L-arginine (L-NNA), indicating involvement of NO. These responses were not affected by tetrodotoxin, implying that the PAR effects are not neurally mediated. On the other hand, PAR4 agonists GYPGKF-NH2, GYPGQV-NH2 and AYPGKF-NH2 did not cause relaxation or contraction, suggesting that PAR4 is not involved in the sphincter motility. Taken together, these results demonstrate that both PAR1 and PAR2 mediate relaxation of the guinea pig IAS through the NO pathway. PAR1 and PAR2 may regulate IAS tone and might be potential therapeutic targets for anal motility disorders. PMID:24631471

  15. Techniques for measuring intercepted and absorbed PAR in corn canopies

    NASA Technical Reports Server (NTRS)

    Gallo, K. P.; Daughtry, C. S. T.

    1984-01-01

    The quantity of radiation potentially available for photosynthesis that is captured by the crop is best described as absorbed photosynthetically active radiation (PAR). Absorbed PAR (APAR) is the difference between descending and ascending fluxes. The four components of APAR were measured above and within two planting densities of corn (Zea mays L.) and several methods of measuring and estimating APAR were examined. A line quantum sensor that spatially averages the photosynthetic photon flux density provided a rapid and portable method of measuring APAR. PAR reflectance from the soil (Typic Argiaquoll) surface decreased from 10% to less than 1% of the incoming PAR as the canopy cover increased. PAR reflectance from the canopy decreased to less than 3% at maximum vegetative cover. Intercepted PAR (1 - transmitted PAR) generally overestimated absorbed PAR by less than 4% throughout most of the growing season. Thus intercepted PAR appears to be a reasonable estimate of absorbed PAR.

  16. Location of deuterium sites at operating temperature from neutron diffraction of BaIn0.6Ti0.2Yb0.2O2.6-n(OH)2n, an electrolyte for proton-solid oxide fuel cells.

    PubMed

    Jarry, Angélique; Joubert, Olivier; Suard, Emmanuelle; Zanotti, Jean Marc; Quarez, Eric

    2016-06-21

    A fundamental understanding of the doping effect on the hydration mechanism and related proton diffusion pathways are keys to the progress of Proton-Solid Oxide Fuel Cell (H(+)-SOFC) technologies. Here, we elucidate the possible interplay between the crystal structure upon hydration and the conductivity properties in a promising perovskite type H(+)-SOFC electrolyte, BaIn0.6Yb0.2Ti0.2O2.6-n(OH)2n. Thermal X-ray and neutron diffractions, neutron time-of-flight scattering along with thermal gravimetric analysis reveal the structural features of BaIn0.6Ti0.2Yb0.2O2.6-n(OH)2n at fuel cell operating temperatures. Between 400-600 °C, BaIn0.6Yb0.2Ti0.2O2.6-n(OD)2n (n < 0.042) remains in a disordered perovskite structure with high anisotropies in the form of oblate spheroids for oxygen. At 400 °C, the presence of oxygen and proton static disorder is clearly established. Yet, the insertion of mobile protons in 24k sites does not induce long-range structural distortion while facilitating both inter- and intra-octahedral proton transfers via quasi-linear O-DO bonds, strong hydrogen bonding, and octahedral tilting. This experimental evidence reveals that the co-doping approach on Ba2In2O5 enhances greatly protonic conductivity levels by enabling a continuous proton diffusion pathway through BaIn0.6Yb0.2Ti0.2O2.6-n(OH)2n. These new insights into the doping effect on the proton-transfer mechanism offer new perspectives for the development of H(+)-SOFC electrolyte materials. PMID:27225228

  17. Location of deuterium sites at operating temperature from neutron diffraction of BaIn0.6Ti0.2Yb0.2O2.6-n(OH)2n, an electrolyte for proton-solid oxide fuel cells.

    PubMed

    Jarry, Angélique; Joubert, Olivier; Suard, Emmanuelle; Zanotti, Jean Marc; Quarez, Eric

    2016-06-21

    A fundamental understanding of the doping effect on the hydration mechanism and related proton diffusion pathways are keys to the progress of Proton-Solid Oxide Fuel Cell (H(+)-SOFC) technologies. Here, we elucidate the possible interplay between the crystal structure upon hydration and the conductivity properties in a promising perovskite type H(+)-SOFC electrolyte, BaIn0.6Yb0.2Ti0.2O2.6-n(OH)2n. Thermal X-ray and neutron diffractions, neutron time-of-flight scattering along with thermal gravimetric analysis reveal the structural features of BaIn0.6Ti0.2Yb0.2O2.6-n(OH)2n at fuel cell operating temperatures. Between 400-600 °C, BaIn0.6Yb0.2Ti0.2O2.6-n(OD)2n (n < 0.042) remains in a disordered perovskite structure with high anisotropies in the form of oblate spheroids for oxygen. At 400 °C, the presence of oxygen and proton static disorder is clearly established. Yet, the insertion of mobile protons in 24k sites does not induce long-range structural distortion while facilitating both inter- and intra-octahedral proton transfers via quasi-linear O-DO bonds, strong hydrogen bonding, and octahedral tilting. This experimental evidence reveals that the co-doping approach on Ba2In2O5 enhances greatly protonic conductivity levels by enabling a continuous proton diffusion pathway through BaIn0.6Yb0.2Ti0.2O2.6-n(OH)2n. These new insights into the doping effect on the proton-transfer mechanism offer new perspectives for the development of H(+)-SOFC electrolyte materials.

  18. Tube plug inspection system

    SciTech Connect

    Pirl, W.E.; Ray, E.A.; Costlow, A.M.; Roth, C.H. Jr.; Gradich, F.X.; Chizmar, D.A.

    1992-03-31

    This patent describes a system for inspecting a tube plug defining a chamber therein and having an open end in communication with the chamber, the chamber having disposed therein an expander element having a bore therethrough. It comprises: probe means having a sensor probe connected thereto for inspecting the tube plug, the probe means capable of being connected to the tube plug for extending the sensor probe a predetermined distance into the chamber through the open end of the tube plug; means connected to the probe means for rotating and translating the sensor probe within the chamber to provide an inspection scan interiorly of the tube plug, the rotating and translating means including: a flexible hose connected to the probe means for translating and rotating the probe means, the hose having adjacent segments so that the hose is flexible; and a connector interposed between adjacent segments of the hose for maintaining the hose in a tangle-free state; and drive means engaging the rotating and translating means for driving the rotating and translating means.

  19. Neural tube defects.

    PubMed

    Greene, Nicholas D E; Copp, Andrew J

    2014-01-01

    Neural tube defects (NTDs), including spina bifida and anencephaly, are severe birth defects of the central nervous system that originate during embryonic development when the neural tube fails to close completely. Human NTDs are multifactorial, with contributions from both genetic and environmental factors. The genetic basis is not yet well understood, but several nongenetic risk factors have been identified as have possibilities for prevention by maternal folic acid supplementation. Mechanisms underlying neural tube closure and NTDs may be informed by experimental models, which have revealed numerous genes whose abnormal function causes NTDs and have provided details of critical cellular and morphological events whose regulation is essential for closure. Such models also provide an opportunity to investigate potential risk factors and to develop novel preventive therapies. PMID:25032496

  20. PRODUCTION OF URANIUM TUBING

    DOEpatents

    Creutz, E.C.

    1958-04-15

    The manufacture of thin-walled uranium tubing by the hot-piercing techique is described. Uranium billets are preheated to a temperature above 780 d C. The heated billet is fed to a station where it is engaged on its external surface by three convex-surfaced rotating rollers which are set at an angle to the axis of the billet to produce a surface friction force in one direction to force the billet over a piercing mandrel. While being formed around the mandrel and before losing the desired shape, the tube thus formed is cooled by a water spray.

  1. Microtubules, polarity and vertebrate neural tube morphogenesis.

    PubMed

    Cearns, Michael D; Escuin, Sarah; Alexandre, Paula; Greene, Nicholas D E; Copp, Andrew J

    2016-07-01

    Microtubules (MTs) are key cellular components, long known to participate in morphogenetic events that shape the developing embryo. However, the links between the cellular functions of MTs, their effects on cell shape and polarity, and their role in large-scale morphogenesis remain poorly understood. Here, these relationships were examined with respect to two strategies for generating the vertebrate neural tube: bending and closure of the mammalian neural plate; and cavitation of the teleost neural rod. The latter process has been compared with 'secondary' neurulation that generates the caudal spinal cord in mammals. MTs align along the apico-basal axis of the mammalian neuroepithelium early in neural tube closure, participating functionally in interkinetic nuclear migration, which indirectly impacts on cell shape. Whether MTs play other functional roles in mammalian neurulation remains unclear. In the zebrafish, MTs are important for defining the neural rod midline prior to its cavitation, both by localizing apical proteins at the tissue midline and by orienting cell division through a mirror-symmetric MT apparatus that helps to further define the medial localization of apical polarity proteins. Par proteins have been implicated in centrosome positioning in neuroepithelia as well as in the control of polarized morphogenetic movements in the neural rod. Understanding of MT functions during early nervous system development has so far been limited, partly by techniques that fail to distinguish 'cause' from 'effect'. Future developments will likely rely on novel ways to selectively impair MT function in order to investigate the roles they play.

  2. PAR polarity: from complexity to design principles.

    PubMed

    Goehring, Nathan W

    2014-11-01

    The par-titioning-defective or PAR proteins comprise the core of an essential cell polarity network that underlies polarization in a wide variety of cell types and developmental contexts. The output of this network in nearly every case is the establishment of opposing and complementary membrane domains that define a cell׳s polarity axis. Yet, behind this simple pattern is a complex system of interactions, regulation and dynamic behaviors. How these various parts combine to generate polarized patterns of protein localization in cells is only beginning to become clear. This review, part of the Special Issue on Cell Polarity, aims to highlight several emerging themes and design principles that underlie the process of cell polarization by components of the PAR network. PMID:25128809

  3. Humanizing the Protease-Activated Receptor (PAR) Expression Profile in Mouse Platelets by Knocking PAR1 into the Par3 Locus Reveals PAR1 Expression Is Not Tolerated in Mouse Platelets

    PubMed Central

    French, Shauna L.; Paramitha, Antonia C.; Moon, Mitchell J.; Dickins, Ross A.; Hamilton, Justin R.

    2016-01-01

    Anti-platelet drugs are the mainstay of pharmacotherapy for heart attack and stroke prevention, yet improvements are continually sought. Thrombin is the most potent activator of platelets and targeting platelet thrombin receptors (protease-activated receptors; PARs) is an emerging anti-thrombotic approach. Humans express two PARs on their platelets–PAR1 and PAR4. The first PAR1 antagonist was recently approved for clinical use and PAR4 antagonists are in early clinical development. However, pre-clinical studies examining platelet PAR function are challenging because the platelets of non-primates do not accurately reflect the PAR expression profile of human platelets. Mice, for example, express Par3 and Par4. To address this limitation, we aimed to develop a genetically modified mouse that would express the same repertoire of platelet PARs as humans. Here, human PAR1 preceded by a lox-stop-lox was knocked into the mouse Par3 locus, and then expressed in a platelet-specific manner (hPAR1-KI mice). Despite correct targeting and the predicted loss of Par3 expression and function in platelets from hPAR1-KI mice, no PAR1 expression or function was detected. Specifically, PAR1 was not detected on the platelet surface nor internally by flow cytometry nor in whole cell lysates by Western blot, while a PAR1-activating peptide failed to induce platelet activation assessed by either aggregation or surface P-selectin expression. Platelets from hPAR1-KI mice did display significantly diminished responsiveness to thrombin stimulation in both assays, consistent with a Par3-/- phenotype. In contrast to the observations in hPAR1-KI mouse platelets, the PAR1 construct used here was successfully expressed in HEK293T cells. Together, these data suggest ectopic PAR1 expression is not tolerated in mouse platelets and indicate a different approach is required to develop a small animal model for the purpose of any future preclinical testing of PAR antagonists as anti-platelet drugs. PMID

  4. Heat-shrink plastic tubing seals joints in glass tubing

    NASA Technical Reports Server (NTRS)

    Del Duca, B.; Downey, A.

    1968-01-01

    Small units of standard glass apparatus held together by short lengths of transparent heat-shrinkable polyolefin tubing. The tubing is shrunk over glass O-ring type connectors having O-rings but no lubricant.

  5. Tube Feeding Transition Plateaus

    ERIC Educational Resources Information Center

    Klein, Marsha Dunn

    2007-01-01

    The journey children make from tube feeding to oral feeding is personal for each child and family. There is a sequence of predictable plateaus that children climb as they move toward orally eating. By better understanding this sequence, parents and children can maximize the development, learning, enjoyment and confidence at each plateau. The…

  6. Downhole pulse tube refrigerators

    SciTech Connect

    Swift, G.; Gardner, D.

    1997-12-01

    This report summarizes a preliminary design study to explore the plausibility of using pulse tube refrigeration to cool instruments in a hot down-hole environment. The original motivation was to maintain Dave Reagor`s high-temperature superconducting electronics at 75 K, but the study has evolved to include three target design criteria: cooling at 30 C in a 300 C environment, cooling at 75 K in a 50 C environment, cooling at both 75 K and 30 C in a 250 C environment. These specific temperatures were chosen arbitrarily, as representative of what is possible. The primary goals are low cost, reliability, and small package diameter. Pulse-tube refrigeration is a rapidly growing sub-field of cryogenic refrigeration. The pulse tube refrigerator has recently become the simplest, cheapest, most rugged and reliable low-power cryocooler. The authors expect this technology will be applicable downhole because of the ratio of hot to cold temperatures (in absolute units, such as Kelvin) of interest in deep drilling is comparable to the ratios routinely achieved with cryogenic pulse-tube refrigerators.

  7. Innovative solid oxide fuel cells based on BaIn0.3Ti0.7O2.85 electrolyte and La2Mo2O9 amorphous reduced phase as anode material

    NASA Astrophysics Data System (ADS)

    Buvat, Gaëtan; Quarez, Eric; Joubert, Olivier

    2016-01-01

    This article presents elaboration of electrolyte-supported solid oxide fuel cells based on the oxide ion conductor BaIn0.3Ti0.7O2.85 (BIT07) as electrolyte, the amorphous reduced phase of La2Mo2O9 (La2Mo2O7-y) as anode which presents a mixed ionic and electronic conduction in low pO2 and La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) as cathode. Electrode materials have been deposited by screen-printing on BIT07 substrate. In order to avoid chemical reactivity between BIT07 and La2Mo2O9, a thin layer of Ce0.9Gd0.1O1.95 (CGO) has been used. Electrochemical performance of the single cell has been characterized by I-V measurements and impedance spectroscopy. Encouraging performance of 40 mW cm-2 at 700 °C is obtained with a thick electrolyte layer. Finally, ageing test of the cell at 700 °C during 800 h has been done with a low rate of performance loss of 4.4 × 10-3% h-1. No degradation of the electrolyte material is reported and stability of the anode material after operating the fuel cell is discussed.

  8. Description of Litomosoides ysoguazu n. sp. (Nematoda, Onchocercidae), a parasite of the tuft-toed rice rat Sooretamys angouya (Fischer) (Rodentia: Cricetidae), and a first record of L. esslingeri Bain, Petit & Berteaux, 1989 in Paraguay.

    PubMed

    Notarnicola, Juliana; de la Sancha, Noé Ulises

    2015-06-01

    Paraguay is a small landlocked country whose mammalian fauna is among the least studied in South America, as well as their parasites. As a result of a study of the effects of habitat fragmentation on small mammal biodiversity in eastern Paraguay, we have collected some parasites of cricetid rodents. Herein, we describe a new species of Litomosoides Chandler, 1931 parasitising the body cavity of the tuft-toed rice rat Sooretamys angouya (Fischer) and Litomosoides esslingeri Bain, Petit & Diagne, 1989 parasitising Oligoryzomys nigripes (Olfers), thus expanding its geographical distribution into Paraguay. Litomosoides ysoguazu n. sp. is characterised by the large size of the females (92.2-117.6 mm long) and by having buccal capsule with an anterior widening with rounded edges on the chitinous segment and a rounded widening at the base; male tail with a single pair of adcloacal papillae, three to five pairs of asymmetrical postcloacal papillae, and one or two unpaired papillae in the median ventral line; spicules corresponding to the "sigmodontis" species group; and microfilaria with a sheath stuck to the body and visible in the anterior extremity. We also describe a fourth-stage female larva. Oligoryzomys nigripes is a new host record of L. esslingeri; this enlarges the host record to eight species highlighting the low specificity of this species. PMID:25962465

  9. Description of Litomosoides ysoguazu n. sp. (Nematoda, Onchocercidae), a parasite of the tuft-toed rice rat Sooretamys angouya (Fischer) (Rodentia: Cricetidae), and a first record of L. esslingeri Bain, Petit & Berteaux, 1989 in Paraguay.

    PubMed

    Notarnicola, Juliana; de la Sancha, Noé Ulises

    2015-06-01

    Paraguay is a small landlocked country whose mammalian fauna is among the least studied in South America, as well as their parasites. As a result of a study of the effects of habitat fragmentation on small mammal biodiversity in eastern Paraguay, we have collected some parasites of cricetid rodents. Herein, we describe a new species of Litomosoides Chandler, 1931 parasitising the body cavity of the tuft-toed rice rat Sooretamys angouya (Fischer) and Litomosoides esslingeri Bain, Petit & Diagne, 1989 parasitising Oligoryzomys nigripes (Olfers), thus expanding its geographical distribution into Paraguay. Litomosoides ysoguazu n. sp. is characterised by the large size of the females (92.2-117.6 mm long) and by having buccal capsule with an anterior widening with rounded edges on the chitinous segment and a rounded widening at the base; male tail with a single pair of adcloacal papillae, three to five pairs of asymmetrical postcloacal papillae, and one or two unpaired papillae in the median ventral line; spicules corresponding to the "sigmodontis" species group; and microfilaria with a sheath stuck to the body and visible in the anterior extremity. We also describe a fourth-stage female larva. Oligoryzomys nigripes is a new host record of L. esslingeri; this enlarges the host record to eight species highlighting the low specificity of this species.

  10. ParA and ParB coordinate chromosome segregation with cell elongation and division during Streptomyces sporulation

    PubMed Central

    Donczew, Magdalena; Mackiewicz, Paweł; Wróbel, Agnieszka; Flärdh, Klas; Zakrzewska-Czerwińska, Jolanta

    2016-01-01

    In unicellular bacteria, the ParA and ParB proteins segregate chromosomes and coordinate this process with cell division and chromosome replication. During sporulation of mycelial Streptomyces, ParA and ParB uniformly distribute multiple chromosomes along the filamentous sporogenic hyphal compartment, which then differentiates into a chain of unigenomic spores. However, chromosome segregation must be coordinated with cell elongation and multiple divisions. Here, we addressed the question of whether ParA and ParB are involved in the synchronization of cell-cycle processes during sporulation in Streptomyces. To answer this question, we used time-lapse microscopy, which allows the monitoring of growth and division of single sporogenic hyphae. We showed that sporogenic hyphae stop extending at the time of ParA accumulation and Z-ring formation. We demonstrated that both ParA and ParB affect the rate of hyphal extension. Additionally, we showed that ParA promotes the formation of massive nucleoprotein complexes by ParB. We also showed that FtsZ ring assembly is affected by the ParB protein and/or unsegregated DNA. Our results indicate the existence of a checkpoint between the extension and septation of sporogenic hyphae that involves the ParA and ParB proteins. PMID:27248800

  11. Quarter-wave pulse tube

    NASA Astrophysics Data System (ADS)

    Swift, G. W.; Gardner, D. L.; Backhaus, S. N.

    2011-10-01

    In high-power pulse-tube refrigerators, the pulse tube itself can be very long without too much dissipation of acoustic power on its walls. The pressure amplitude, the volume-flow-rate amplitude, and the time phase between them evolve significantly along a pulse tube that is about a quarter-wavelength long. Proper choice of length and area makes the oscillations at the ambient end of the long pulse tube optimal for driving a second, smaller pulse-tube refrigerator, thereby utilizing the acoustic power that would typically have been dissipated in the first pulse-tube refrigerator's orifice. Experiments show that little heat is carried from the ambient heat exchanger to the cold heat exchanger in such a long pulse tube, even though the oscillations are turbulent and even when the tube is compactly coiled.

  12. Rubens Flame-Tube Demonstration.

    ERIC Educational Resources Information Center

    Ficken, George W.; Stephenson, Francis C.

    1979-01-01

    Investigates and explains the phenomenon associated with Rubens flame-tube demonstration, specifically the persistance of flames at regular intervals along the tube for few minutes after the gas is turned off. (GA)

  13. Vanadium tube processing and analysis

    SciTech Connect

    Kautz, D.D.; Tanaka, G.J.

    1993-08-11

    Vanadium tubing obtained from Century Tubes, a custom tubing manufacturer, was studied to determine as-received quality and fabricability. Applications for this tubing involve crimping and sealing operations at Pantex Plant requiring very high levels of leak-tightness (leak rates less than 10{sup {minus}8} atm-cc He/sec). The as-received material had poor OD and ID surface finish and cleanliness that needed to be improved before use in component fabrication. Savannah River Technical Center (SRTC) personnel developed a cleaning procedure to make this tubing acceptable for crimping and sealing operations. After suitably cleaning the tubing, we tested several tube sealing techniques and all showed some degree of success. Pantex Plant personnel are now implementing a tube sealing process very similar to one of the techniques studied, a mechanical crimp followed by seal welding.

  14. Multiple test tubes stirred mechanically

    NASA Technical Reports Server (NTRS)

    Leon, H. J.; Strong, I. J.

    1965-01-01

    Mechanical device simultaneously stirs multiple test tubes under controlled laboratory conditions. The invention provides a variable stirring rate, minimal amount of contamination of tube contents, unattended and simple operation, and easy maintenance and cleaning.

  15. suPAR and Team Nephrology

    PubMed Central

    2014-01-01

    Primary focal segmental glomerulosclerosis (FSGS) accounts for nearly 10 % of patients who require renal replacement therapy. Elevated circulating levels of soluble urokinase receptor (suPAR) have been identified as a biomarker to discriminate primary FSGS from other glomerulopathies. Subsequent reports have questioned the diagnostic utility of this test. In a study in BMC Medicine, Huang et al. demonstrate that urinary soluble urokinase receptor (suPAR) excretion assists in distinguishing primary FSGS from other glomerular diseases, and that high plasma suPAR concentrations are not directly linked to a decline in glomerular filtration rate (GFR). This observation suggests that further investigation of suPAR is warranted in patients with FSGS. It should be interpreted in light of a recent report that B7-1 is expressed in the podocytes of a subset of patients with FSGS, and that blocking this molecule may represent the first successful targeted intervention for this disease. These advances highlight the rapid pace of scientific progress in the field of nephrology. Nephrologists should work together, share resources, and expedite the design of protocols to evaluate these novel biomarkers in a comprehensive and scientifically valid manner. Please see related article http://www.biomedcentral.com/1741-7015/12/81. PMID:24885021

  16. Composite Cathode-Ray Tube

    NASA Technical Reports Server (NTRS)

    Gangal, Mukund D.

    1988-01-01

    Proposed composite cathode-ray tube consists of rectangular array of cathode-ray tubes joined at edges, sharing common vacuum. Each electron gun generates independent image on portion of screen. Composite tube operates most advantageously under digital control to make available several display modes. Brightness and resolution of large images increased. Useful for classroom presentations, conferences, and the like.

  17. Enteral Tube Feeding and Pneumonia

    ERIC Educational Resources Information Center

    Gray, David Sheridan; Kimmel, David

    2006-01-01

    To determine the effects of enteral tube feeding on the incidence of pneumonia, we performed a retrospective review of all clients at our institution who had gastrostomy or jejunostomy tubes placed over a 10-year period. Ninety-three subjects had a history of pneumonia before feeding tube insertion. Eighty had gastrostomy and 13, jejunostomy…

  18. Tubing rotator reduces tubing wear in rod pumped wells

    SciTech Connect

    Graham, M. ); Brown, C. )

    1994-04-04

    Tubing failures are both expensive and time-consuming. The most common failure results from rod cutting, or, erosion of the tubing ID because of continuous, reciprocating contact with the rod string. Installation of tubing rotators has decreased tubing failures in West Texas waterflood sucker-rod pumped wells. Pumping unit movement powers the rotator system, turning the tubing string at about 1 revolution/day. The rotator system has both surface and subsurface components. A reduction gear box attached to the walking beam converts the pumping unit's reciprocating strokes into rotary motion. A drive line transfers this rotary motion to a gear-driven suspension mandrel in the rotating tubing hanger. Near the bottom of the tubing string, a rotating tubing anchor/catcher allows the entire tubing string, including the tail pipe, seating nipple, and gas and mud anchor to rotate. The rotator hanger suspends the weight of the tubing string on a bearing system. One model of the hanger has a load capacity of 135,000 lb. A surface swivel allows rotation below the pumping tee so that the flow lines remain stationary. Also included in the string is a safety shear coupling to prevent over torquing the tubing.

  19. YouTube Physics

    NASA Astrophysics Data System (ADS)

    Riendeau, Diane

    2012-09-01

    To date, this column has presented videos to show in class, Don Mathieson from Tulsa Community College suggested that YouTube could be used in another fashion. In Don's experience, his students are not always prepared for the mathematic rigor of his course. Even at the high school level, math can be a barrier for physics students. Walid Shihabi, a colleague of Don's, decided to compile a list of YouTube videos that his students could watch to relearn basic mathematics. I thought this sounded like a fantastic idea and a great service to the students. Walid graciously agreed to share his list and I have reproduced a large portion of it below.

  20. Induction plasma tube

    DOEpatents

    Hull, D.E.

    1982-07-02

    An induction plasma tube having a segmented, fluid-cooled internal radiation shield is disclosed. The individual segments are thick in cross-section such that the shield occupies a substantial fraction of the internal volume of the plasma enclosure, resulting in improved performance and higher sustainable plasma temperatures. The individual segments of the shield are preferably cooled by means of a counterflow fluid cooling system wherein each segment includes a central bore and a fluid supply tube extending into the bore. The counterflow cooling system results in improved cooling of the individual segments and also permits use of relatively larger shield segments which permit improved electromagnetic coupling between the induction coil and a plasma located inside the shield. Four embodiments of the invention, each having particular advantages, are disclosed.

  1. Induction plasma tube

    DOEpatents

    Hull, Donald E.

    1984-01-01

    An induction plasma tube having a segmented, fluid-cooled internal radiation shield is disclosed. The individual segments are thick in cross-section such that the shield occupies a substantial fraction of the internal volume of the plasma enclosure, resulting in improved performance and higher sustainable plasma temperatures. The individual segments of the shield are preferably cooled by means of a counterflow fluid cooling system wherein each segment includes a central bore and a fluid supply tube extending into the bore. The counterflow cooling system results in improved cooling of the individual segments and also permits use of relatively larger shield segments which permit improved electromagnetic coupling between the induction coil and a plasma located inside the shield. Four embodiments of the invention, each having particular advantages, are disclosed.

  2. View from east to west of PAR site storage building; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View from east to west of PAR site storage building; formerly PAR dispensary - Stanley R. Mickelsen Safeguard Complex, Storage Building, Across street from Family Housing Units 110 & 111, Nekoma, Cavalier County, ND

  3. View from west to east of PAR site resident engineer's ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View from west to east of PAR site resident engineer's office building (REOB) - Stanley R. Mickelsen Safeguard Complex, Resident Engineers Office Building, Southeast of intersection of PAR Access Road & Fourth Avenue, Nekoma, Cavalier County, ND

  4. A Combined Global and Local Approach to Elucidate Spatial Organization of the Mycobacterial ParB-parS Partition Assembly

    SciTech Connect

    B Chaudhuri; S Gupta; V Urban; M Chance; R DMello; L Smith; K Lyons; J Gee

    2011-12-31

    Combining diverse sets of data at global (size, shape) and local (residue) scales is an emerging trend for elucidating the organization and function of the cellular assemblies. We used such a strategy, combining data from X-ray and neutron scattering with H/D-contrast variation and X-ray footprinting with mass spectrometry, to elucidate the spatial organization of the ParB-parS assembly from Mycobacterium tuberculosis. The ParB-parS participates in plasmid and chromosome segregation and condensation in predivisional bacterial cells. ParB polymerizes around the parS centromere(s) to form a higher-order assembly that serves to recruit cyto-skeletal ParA ATPases and SMC proteins for chromosome segregation. A hybrid model of the ParB-parS was built by combining and correlating computational models with experiment-derived information about size, shape, position of the symmetry axis within the shape, internal topology, DNA-protein interface, exposed surface patches, and prior knowledge. This first view of the ParB-parS leads us to propose how ParB spread on the chromosome to form a larger assembly.

  5. A combined global and local approach to elucidate spatial organization of the Mycobacterial ParB-parS partition assembly.

    PubMed

    Chaudhuri, Barnali N; Gupta, Sayan; Urban, Volker S; Chance, Mark R; D'Mello, Rhijuta; Smith, Lauren; Lyons, Kelly; Gee, Jessica

    2011-03-22

    Combining diverse sets of data at global (size, shape) and local (residue) scales is an emerging trend for elucidating the organization and function of the cellular assemblies. We used such a strategy, combining data from X-ray and neutron scattering with H/D-contrast variation and X-ray footprinting with mass spectrometry, to elucidate the spatial organization of the ParB-parS assembly from Mycobacterium tuberculosis. The ParB-parS participates in plasmid and chromosome segregation and condensation in predivisional bacterial cells. ParB polymerizes around the parS centromere(s) to form a higher-order assembly that serves to recruit cyto-skeletal ParA ATPases and SMC proteins for chromosome segregation. A hybrid model of the ParB-parS was built by combining and correlating computational models with experiment-derived information about size, shape, position of the symmetry axis within the shape, internal topology, DNA-protein interface, exposed surface patches, and prior knowledge. This first view of the ParB-parS leads us to propose how ParB spread on the chromosome to form a larger assembly.

  6. A Combined Global and Local Approach to Elucidate Spatial Organization of the Mycobacterial ParB-parS Partition

    SciTech Connect

    Chaudhuri, Barnali; Gupta, Sayan; Urban, Volker S; Chance, Mark; D'Mello, Rhijuta; Smith, Lauren; Lyons, Kelly; Gee, Jessica

    2010-01-01

    Combining diverse sets of data at global (size, shape) and local (residue) scales is an emerging trend for elucidating the organization and function of the cellular assemblies. We used such a strategy, combining data from X-ray and neutron scattering with H/D-contrast variation and X-ray footprinting with mass spectrometry, to elucidate the spatial organization of the ParB-parS assembly from Mycobacterium tuberculosis. The ParB-parS participates in plasmid and chromosome segregation and condensation in predivisional bacterial cells. ParB polymerizes around the parS centromere(s) to form a higher-order assembly that serves to recruit cyto-skeletal ParA ATPases and SMC proteins for chromosome segregation. A hybrid model of the ParB-parS was built by combining and correlating computational models with experiment-derived information about size, shape, position of the symmetry axis within the shape, internal topology, DNA-protein interface, exposed surface patches, and prior knowledge. This first view of the ParB-parS leads us to propose how ParB spread on the chromosome to form a larger assembly.

  7. [Patulous eustachian tube].

    PubMed

    Kovacević, D; Radosavljević, M; Jelesijević, J

    1995-01-01

    Patulous eustachian tube is a pathological condition which exists more often than we make a diagnosis, and a patient is not often aware of his disease. This disease can be manifested with various symptoms: respiratory synchrony noises in the ear, because of the penetration of the air current through the eustachian tube and with the movement of the eardrum outwards and inside, with autophony, reduction of the hearing, the buzzing, dizziness and disturbance of the balance. Two patients are presented. The first one was sick for many years from various chronics exhausted diseases: Jackson's epilepsy, temporary vascular brain disturbances, tuberculosis of lung, stomach ulcer, heart diseases, the patient is from low class, on one side, and also suffers from some local diseases: a paralysis of soft palate and palatal arcs, a chronic catarrhal rhinitis and sinusitis, a deviation of nasal dividing wall and hindered breathing through the nose, on the other side. Many years the patient didn't know for patological condition in the ears and in the eustachian tubes. After improving the hygienic conditions, the physical condition and local therapy, the patient felt much better. The second patient, with considerable shorter evolution of the disease and mild symptomatology, showed the amplified symptoms of the disease of the Eustachian tube in the course of the acute otitis. It is attained a satisfying calming of the manifestative symptoms by remedy therapie. Man must thing about possibility of the appearance of this pathology condition in various disease or conditions, which can take to the fast lost of the weight and physical and moral exhaustion of the patient, i.e. an adult, first as the protection of the appearance of the disease (condition) and afterwards, eventually early and regulary treatment in order to prevent various possible, above mentioned complications. PMID:16296237

  8. Joined concentric tubes

    SciTech Connect

    DeJonghe, Lutgard; Jacobson, Craig; Tucker, Michael; Visco, Steven

    2013-01-01

    Tubular objects having two or more concentric layers that have different properties are joined to one another during their manufacture primarily by compressive and friction forces generated by shrinkage during sintering and possibly mechanical interlocking. It is not necessary for the concentric tubes to display adhesive-, chemical- or sinter-bonding to each other in order to achieve a strong bond. This facilitates joining of dissimilar materials, such as ceramics and metals.

  9. Traveling-Wave Tubes

    NASA Technical Reports Server (NTRS)

    Kory, Carol L.

    1998-01-01

    The traveling-wave tube (TWT) is a vacuum device invented in the early 1940's used for amplification at microwave frequencies. Amplification is attained by surrendering kinetic energy from an electron beam to a radio frequency (RF) electromagnetic wave. The demand for vacuum devices has been decreased largely by the advent of solid-state devices. However, although solid state devices have replaced vacuum devices in many areas, there are still many applications such as radar, electronic countermeasures and satellite communications, that require operating characteristics such as high power (Watts to Megawatts), high frequency (below 1 GHz to over 100 GHz) and large bandwidth that only vacuum devices can provide. Vacuum devices are also deemed irreplaceable in the music industry where musicians treasure their tube-based amplifiers claiming that the solid-state and digital counterparts could never provide the same "warmth" (3). The term traveling-wave tube includes both fast-wave and slow-wave devices. This article will concentrate on slow-wave devices as the vast majority of TWTs in operation fall into this category.

  10. Concentric tube support assembly

    DOEpatents

    Rubio, Mark F.; Glessner, John C.

    2012-09-04

    An assembly (45) includes a plurality of separate pie-shaped segments (72) forming a disk (70) around a central region (48) for retaining a plurality of tubes (46) in a concentrically spaced apart configuration. Each segment includes a support member (94) radially extending along an upstream face (96) of the segment and a plurality of annularly curved support arms (98) transversely attached to the support member and radially spaced apart from one another away from the central region for receiving respective upstream end portions of the tubes in arc-shaped spaces (100) between the arms. Each segment also includes a radial passageway (102) formed in the support member for receiving a fluid segment portion (106) and a plurality of annular passageways (104) formed in the support arms for receiving respective arm portions (108) of the fluid segment portion from the radial passageway and for conducting the respective arm portions into corresponding annular spaces (47) formed between the tubes retained by the disk.

  11. TUBE SHEARING VALVE

    DOEpatents

    Wilner, L.B.

    1960-05-24

    Explosive operated valves can be used to join two or more containers in fluid flow relationship, one such container being a sealed reservoir. The valve is most simply disposed by mounting it on the reservoir so thst a tube extends from the interior of the reservoir through the valve body, terminating at the bottom of the bore in a closed end; other containers may be similarly connected or may be open connected, as desired. The piston of the valve has a cutting edge at its lower end which shears off the closed tube ends and a recess above the cutting edge to provide a flow channel. Intermixing of the fluid being transferred with the explosion gases is prevented by a copper ring at the top of the piston which is force fitted into the bore at the beginning of the stroke. Although designed to avoid backing up of the piston at pressures up to 10,000 psi in the transferred fluid, proper operation is independent of piston position, once the tube ends were sheared.

  12. Tube bundle system

    PubMed Central

    Marchewka, W.; Mohamed, K.; Addis, J.; Karnack, F.

    2015-01-01

    A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fire or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. Most longwall coal mines in Australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflow monitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine PMID:26306052

  13. Linearisation par pre-distorsion cubique d'un tube a ondes progressives en bande C

    NASA Astrophysics Data System (ADS)

    Hadouej, Taher

    TWTAs are widely used in satellite communications (as for example repeater payloads) that require important amount of power at very high frequencies (above 4 GHz). While providing power rates of Kwatts with good efficiency, TWTA lack in linearity where up to 6 dB output back off is needed to reduce distortions. This is a huge loss compared to the maximum output power that can be provided by these amplifiers. In order to overcome this problem, analog predistortion is presented as a very effective linearization method in terms of integration, cost and linearity. In this context, we are aiming to design, manufacture and test a predistortion circuit based on two path configuration. In the non-linear path, the distortion generator can provide an expansion or a compression depending on the biasing of the Schottky diodes. Consequently, the linearizer, with different control circuits (input amplification, attenuator, phase shifter), can nearly fit the reverse function of the amplifier. The assembled circuit was tested around 5.2 GHz. In CW (Continuous Wave) test, an improvement of 1.7 dB of 1dB compression output power was achieved while reducing gain compression to 2.6 dB (down from 7.3 dB) and phase lag to 12 degrees (down from 26) near saturation. At 6 dB output back-off, ACPR with QAM-16 signal and C/I3 were improved by 7 dB and 15 dB respectively. This allowed a gain of 2.5 dB in power output at 40 dBc ACPR. Key words: TWTA, non-linearity, analog predistorsion, Target, Distortion generator, Schottky.

  14. Host response biomarker in sepsis: suPAR detection.

    PubMed

    Giamarellos-Bourboulis, Evangelos J; Georgitsi, Marianna

    2015-01-01

    Recent studies of our group have shown that suPAR may complement APACHE II score for risk assessment in sepsis. suPAR may be measured in serum of patients by an enzyme immunosorbent assay developed by Virogates (suPARnostic™). Production of suPAR from circulating neutrophils and monocytes may be assessed after isolation of neutrophils and monocytes and ex vivo culture. This is followed by measurement of suPAR in culture supernatants.

  15. Apparatus Splits Glass Tubes Longitudinally

    NASA Technical Reports Server (NTRS)

    Shaw, Ernest; Manahan, Robert O'neil

    1993-01-01

    Tubes split into half cylinders by hot-wire/thermal-shock method. Tube to be cut placed on notched jig in apparatus. Nichrome wire stretched between arms of pivoted carriage and oriented parallel to notch. Wire heated by electrical current while resting on tube. After heating for about 1 minute for each millimeter of thickness of glass, tube quenched in water and split by resulting thermal shock. Apparatus used to split tubes in sizes ranging from 3/8 in. in diameter by 1 in. long to 1 1/2 in. in diameter by 4 in. long.

  16. Reliability of steam generator tubing

    SciTech Connect

    Kadokami, E.

    1997-02-01

    The author presents results on studies made of the reliability of steam generator (SG) tubing. The basis for this work is that in Japan the issue of defects in SG tubing is addressed by the approach that any detected defect should be repaired, either by plugging the tube or sleeving it. However, this leaves open the issue that there is a detection limit in practice, and what is the effect of nondetectable cracks on the performance of tubing. These studies were commissioned to look at the safety issues involved in degraded SG tubing. The program has looked at a number of different issues. First was an assessment of the penetration and opening behavior of tube flaws due to internal pressure in the tubing. They have studied: penetration behavior of the tube flaws; primary water leakage from through-wall flaws; opening behavior of through-wall flaws. In addition they have looked at the question of the reliability of tubing with flaws during normal plant operation. Also there have been studies done on the consequences of tube rupture accidents on the integrity of neighboring tubes.

  17. Hybrid endotracheal tubes

    NASA Astrophysics Data System (ADS)

    Sakezles, Christopher Thomas

    Intubation involves the placement of a tube into the tracheal lumen and is prescribed in any setting in which the airway must be stabilized or the patient anesthetized. The purpose of the endotracheal tube in these procedures is to maintain a viable airway, facilitate mechanical ventilation, allow the administration of anesthetics, and prevent the reflux of vomitus into the lungs. In order to satisfy these requirements a nearly airtight seal must be maintained between the tube and the tracheal lining. Most conventional endotracheal tubes provide this seal by employing a cuff that is inflated once the tube is in place. However, the design of this cuff and properties of the material are a source of irritation and injury to the tracheal tissues. In fact, the complication rate for endotracheal intubation is reported to be between 10 and 60%, with manifestations ranging from severe sore throat to erosion through the tracheal wall. These complications are caused by a combination of the materials employed and the forces exerted by the cuff on the tracheal tissues. In particular, the abrasive action of the cuff shears cells from the lining, epithelium adhering to the cuff is removed during extubation, and normal forces exerted on the basement tissues disrupt the blood supply and cause pressure necrosis. The complications associated with tracheal intubation may be reduced or eliminated by employing airway devices constructed from hydrogel materials. Hydrogels are a class of crosslinked polymers which swell in the presence of moisture, and may contain more than 95% water by weight. For the current study, several prototype airway devices were constructed from hydrogel materials including poly(vinyl alcohol), poly(hydroxyethyl methacrylate), and poly(vinyl pyrrolidone). The raw hydrogel materials from this group were subjected to tensile, swelling, and biocompatibility testing, while the finished devices were subjected to extensive mechanical simulation and animal trials

  18. Liquid-Nitrogen Test for Blocked Tubes

    NASA Technical Reports Server (NTRS)

    Wagner, W. R.

    1984-01-01

    Nondestructive test identifies obstructed tube in array of parallel tubes. Trickle of liquid nitrogen allowed to flow through tube array until array accumulates substantial formation of frost from moisture in air. Flow stopped and warm air introduced into inlet manifold to heat tubes in array. Tubes still frosted after others defrosted identified as obstructed tubes. Applications include inspection of flow systems having parallel legs.

  19. Proteinase-activated receptors (PARs) as targets for antiplatelet therapy.

    PubMed

    Cunningham, Margaret; McIntosh, Kathryn; Bushell, Trevor; Sloan, Graeme; Plevin, Robin

    2016-04-15

    Since the identification of the proteinase-activated receptor (PAR) family as mediators of serine protease activity in the 1990s, there has been tremendous progress in the elucidation of their pathophysiological roles. The development of drugs that target PARs has been the focus of many laboratories for the potential treatment of thrombosis, cancer and other inflammatory diseases. Understanding the mechanisms of PAR activation and G protein signalling pathways evoked in response to the growing list of endogenous proteases has yielded great insight into receptor regulation at the molecular level. This has led to the development of new selective modulators of PAR activity, particularly PAR1. The mixed success of targeting PARs has been best exemplified in the context of inhibiting PAR1 as a new antiplatelet therapy. The development of the competitive PAR1 antagonist, vorapaxar (Zontivity), has clearly shown the value in targeting PAR1 in acute coronary syndrome (ACS); however the severity of associated bleeding with this drug has limited its use in the clinic. Due to the efficacy of thrombin acting via PAR1, strategies to selectively inhibit specific PAR1-mediated G protein signalling pathways or to target the second thrombin platelet receptor, PAR4, are being devised. The rationale behind these alternative approaches is to bias downstream thrombin activity via PARs to allow for inhibition of pro-thrombotic pathways but maintain other pathways that may preserve haemostatic balance and improve bleeding profiles for widespread clinical use. This review summarizes the structural determinants that regulate PARs and the modulators of PAR activity developed to date.

  20. Les Brulures Chimiques Par Le Laurier Rose

    PubMed Central

    Bakkali, H.; Ababou, M.; Nassim Sabah, T.; Moussaoui, A.; Ennouhi, A.; Fouadi, F.Z.; Siah, S.; Ihrai, H.

    2010-01-01

    Summary Le laurier rose ou Nerium oleander est un arbuste qui pousse naturellement dans les régions méditerranéennes. Au Maroc on le trouve dans les lieux humides. Il est réputé par ses risques de toxicité systémique en cas d'empoisonnement à cause de la présence de deux alcaloïdes, surtout l'oléandrine. La littérature illustre des cas d'utilisation locale des feuilles de cette plante contre la gale, les hémorroïdes et les furoncles. Nous rapportons deux cas de brûlures chimiques par le laurier rose de gravité différente. Cela doit aboutir à une information élargie de la population, ainsi qu'une réglementation stricte de sa commercialisation. PMID:21991211

  1. Discovery of Octahydroindenes as PAR1 Antagonists

    PubMed Central

    2013-01-01

    Octahydroindene was identified as a novel scaffold for protease activated receptor 1 (PAR1) antagonists. Herein, the 2-position (C2) was explored for structure–activity relationship (SAR) studies. Compounds 14, 19, and 23b showed IC50 values of 1.3, 8.6, and 2.7 nM in a PAR1 radioligand binding assay, respectively, and their inhibitory activities on platelet activation were comparable to that of vorapaxar in a platelet rich plasma (PRP) aggregation assay. This series of compounds showed high potency and no significant cytotoxicity; however, the compounds were metabolically unstable in both human and rat liver microsomes. Current research efforts are focused on optimizing the compounds to improve metabolic stability and physicochemical properties as well as potency. PMID:24900604

  2. Water-Quality Data, 1999-2005, and Ground-Water Level Data, 2004-2005, for McBaine Bottoms, Including the Eagle Bluffs Conservation Area, Columbia, Missouri

    USGS Publications Warehouse

    Smith, Brenda J.; Richards, Joseph M.

    2006-01-01

    The U.S. Geological Survey, in cooperation with the city of Columbia, Missouri, and the Missouri Department of Conservation, collected ground-water quality data from June 1999 through August 2005, surface-water quality data from August 1999 through August 2003, and water-level data from February 2004 through August 2005 in McBaine Bottoms, southwest of Columbia. McBaine Bottoms, adjacent to the Missouri River, is the location of the municipal-supply well field for the city of Columbia, the city of Columbia wastewater-treatment wetlands, and the Missouri Department of Conservation Eagle Bluffs Conservation Area. This report presents water-quality data, which include water-quality analyses of samples collected from 36 water-quality sampling sites (31 were wells and 5 were surface-water sites), and ground-water level data, which include water-level measurements from more than 80 wells. Water samples were analyzed for physical properties, inorganic chemical constituents, nutrients, and dissolved iron. Selected samples were analyzed for trace elements, wastewater organic compounds, and pesticides. In samples from monitoring wells, chloride concentrations ranged from 2.41 to 259 mg/L (milligrams per liter), sodium concentrations ranged from 1.08 to 175 mg/L, and sulfate concentrations ranged from less than 0.2 to 271 mg/L (all concentrations were dissolved). Dissolved nitrite plus nitrate as nitrogen concentrations ranged from less than 0.05 to 0.46 mg/L. Total phosphorous concentrations ranged from less than 0.04 to 1.68 mg/L, dissolved phosphorous concentrations ranged from less than 0.04 to 1.50 mg/L, and dissolved orthophosphorous concentrations ranged from less than 0.01 to 1.83 mg/L. Dissolved iron concentrations ranged from less than 6 to 42,900 g/L (micrograms per liter). Dissolved arsenic concentrations in samples from two monitoring wells ranged from 11 to 37 g/L. In samples from surface-water sampling sites, chloride concentrations ranged from 8.67 to 289 mg

  3. Combined DSEK and Transconjunctival Pars Plana Vitrectomy

    PubMed Central

    Sane, Mona; Shaikh, Naazli

    2016-01-01

    We report here three patients who underwent combined Descemet's stripping with endothelial keratoplasty and transconjunctival pars plana vitrectomy for bullous keratopathy and posterior segment pathology. A surgical technique and case histories are described. Anatomic and visual outcomes of combined Descemet's stripping with endothelial keratoplasty and vitrectomy were excellent. Our experience provides technical guidelines and limitations. The combined minimally invasive techniques allow for rapid anatomical recovery and return of function and visual acuity in a single sitting. PMID:27413563

  4. Par Pond refill water quality sampling

    SciTech Connect

    Koch, J.W. II; Martin, F.D.; Westbury, H.M.

    1996-08-01

    This study was designed to document anoxia and its cause in the event that the anoxia caused a fish kill. However, no fish kill was observed during this study, and dissolved oxygen and nutrient concentrations generally remained within the range expected for southeastern reservoirs. Par Pond water quality monitoring will continue during the second summer after refill as the aquatic macrophytes become reestablished and nutrients in the sediments are released to the water column.

  5. RBMK pressure tube rupture assessment

    SciTech Connect

    Schmitt, B.E.; Tsiklauri, G.V.

    1994-08-01

    The Russian RBMK reactor core design consists of multiple parallel pressure tube channels that contain Zr clad, UO{sub 2} fuel pin bundles. These parallel channels are contained within graphite moderator blocks which are, in turn, contained within a sealed core cavity. Current safety evaluation efforts of the RBMK reactors have been concentrating in the area of tube ruptures within the core cavity and, in particular, multiple tube ruptures that could threaten the reactor core integrity. Tube rupture events result in a pressurization of the reactor core cavity. The original design overpressure for the cavity region was based on a single tube rupture, resulting in considerable margin to the top plate lift pressure. The top plate lift pressure is 3.1 bar, and a single tube rupture would result in approximately 1.4 bar. RBMK plant specific cavity pressure relief designs provide for between three and in simultaneous tube ruptures before exceeding the top plate lift pressure. Thus, current safety evaluations have begun to examine the potential for multiple tube ruptures that could exceed the current cavity pressure relief designs. One such scenario being examined is a partial rupture in a group distribution header that results in stagnated (low) flow to up to 40 pressure tubes. The subsequent fuel heatup in these reduced flow tubes could result in multiple tube ruptures beyond the design relief capacity of the core cavity. This paper examines several key issues in evaluating this transient, including: (1) the effects of low flow, (2) the effects of axial peaking, and (3) the effects of radial peaking, all relative to the time to tube rupture. These issues each play a significant role in attempting to evaluate the likelihood and severity of multiple tube ruptures for a partial group distribution header break.

  6. Gyrotron transmitting tube

    NASA Technical Reports Server (NTRS)

    Kosmahl, H. G. (Inventor)

    1983-01-01

    An RF transmitting tube for the 20 GHz to 500 GHz range comprises a gyrotron and a multistage depressed collector. A winding provides a magnetic field which acts on spent, spinning or orbiting electrons changing their motion to substantially forward linear motion in a downstream direction. The spent electrons then pass through a focusser into the collector. Nearly all of the electrons injected into the collector will remain within an imaginary envelope as they travel forward toward the end collector plate. The apertures in the collector plates are at least as large in diameter as the envelope at any particular axial position.

  7. Lava Tube Collapse Pits

    NASA Technical Reports Server (NTRS)

    2004-01-01

    [figure removed for brevity, see original site]

    We will be looking at collapse pits for the next two weeks. Collapse pits on Mars are formed in several ways. In volcanic areas, channelized lava flows can form roofs which insulate the flowing lava. These features are termed lava tubes on Earth and are common features in basaltic flows. After the lava has drained, parts of the roof of the tube will collapse under its own weight. These collapse pits will only be as deep as the bottom of the original lava tube. Another type of collapse feature associated with volcanic areas arises when very large eruptions completely evacuate the magma chamber beneath the volcano. The weight of the volcano will cause the entire edifice to subside into the void space below it. Structural features including fractures and graben will form during the subsidence. Many times collapse pits will form within the graben. In addition to volcanic collapse pits, Mars has many collapse pits formed when volatiles (such as subsurface ice) are released from the surface layers. As the volatiles leave, the weight of the surrounding rock causes collapse pits to form.

    These collapse pits are found in the southern hemisphere of Mars. They are likely lava tube collapse pits related to flows from Hadriaca Patera.

    Image information: VIS instrument. Latitude -36.8, Longitude 89.6 East (270.4 West). 19 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space

  8. Gastrostomy tube dislodgment acute pancreatitis

    PubMed Central

    2014-01-01

    Percutaneous gastrostomy is well established root for long term feeding of patients who cannot be fed orally. The risks of percutanous gastrostomy insertion are low. Tube related complications often resolved by placing a Foley catheter or other balloon gastrostomy tube as a temporary solution. Gastrostomy tube related gastric, duodenal and billiary obstruction were reported. Gastrostomy tube related pancreatitis is scarcely described. We described a patient who suffered a pancreatitis related to Foley catheter gastrostomy dislodgment. Reviewing all reported cases of gastrostomy related pancreatitis revealed higher incidence in patient with Foley catheter used as gastrostomy and revealed questionable trends in conducting tube replacement. We suggest a proper manner for tube replacement and concluded that should a Foley catheter used as a temporary solution a replacement should be schedule in a timely manner to avoid life threatening complications. PMID:24674106

  9. Steam generator tube integrity program

    SciTech Connect

    Dierks, D.R.; Shack, W.J.; Muscara, J.

    1996-03-01

    A new research program on steam generator tubing degradation is being sponsored by the U.S. Nuclear Regulatory Commission (NRC) at Argonne National Laboratory. This program is intended to support a performance-based steam generator tube integrity rule. Critical areas addressed by the program include evaluation of the processes used for the in-service inspection of steam generator tubes and recommendations for improving the reliability and accuracy of inspections; validation and improvement of correlations for evaluating integrity and leakage of degraded steam generator tubes, and validation and improvement of correlations and models for predicting degradation in steam generator tubes as aging occurs. The studies will focus on mill-annealed Alloy 600 tubing, however, tests will also be performed on replacement materials such as thermally-treated Alloy 600 or 690. An overview of the technical work planned for the program is given.

  10. Two new hemoglobin variants: Hb Aix-Les-Bains [β5(A2)Pro→Leu; HBB:c.17 C>T] and Hb Dubai [α122(H5)His→Leu (α2); HBA2:c.368 A>T].

    PubMed

    Joly, Philippe; Garcia, Caroline; Lacan, Philippe; Couprie, Nicole; Francina, Alain

    2011-01-01

    We report two new hemoglobin (Hb) variants; one causing an impairment of the N-terminal glycation of the β-globin chain and the other a hematological phenotype of α-thalassemia (α-thal). The first variant is Hb Aix-les-Bains [β5(A2)Pro→Leu] and the second Hb Dubai [α122(H5)His→Leu (α2)]. These two new Hb variants were detected by chromatographic and electrophoretic methods and characterized by molecular studies. Hb Dubai gives an α-thalassemic phenotype and should be routinely detected for preventing severe Hb H disease in couples at-risk for α-thal.

  11. Free compression tube. Applications

    NASA Astrophysics Data System (ADS)

    Rusu, Ioan

    2012-11-01

    During the flight of vehicles, their propulsion energy must overcome gravity, to ensure the displacement of air masses on vehicle trajectory, to cover both energy losses from the friction between a solid surface and the air and also the kinetic energy of reflected air masses due to the impact with the flying vehicle. The flight optimization by increasing speed and reducing fuel consumption has directed research in the aerodynamics field. The flying vehicles shapes obtained through studies in the wind tunnel provide the optimization of the impact with the air masses and the airflow along the vehicle. By energy balance studies for vehicles in flight, the author Ioan Rusu directed his research in reducing the energy lost at vehicle impact with air masses. In this respect as compared to classical solutions for building flight vehicles aerodynamic surfaces which reduce the impact and friction with air masses, Ioan Rusu has invented a device which he named free compression tube for rockets, registered with the State Office for Inventions and Trademarks of Romania, OSIM, deposit f 2011 0352. Mounted in front of flight vehicles it eliminates significantly the impact and friction of air masses with the vehicle solid. The air masses come into contact with the air inside the free compression tube and the air-solid friction is eliminated and replaced by air to air friction.

  12. Tubing for augmented heat transfer

    SciTech Connect

    Yampolsky, J.S.; Pavlics, P.

    1983-08-01

    The objectives of the program reported were: to determine the heat transfer and friction characteristics on the outside of spiral fluted tubing in single phase flow of water, and to assess the relative cost of a heat exchanger constructed with spiral fluted tubing with one using conventional smooth tubing. An application is examined where an isolation water/water heat exchanger was used to transfer the heat from a gaseous diffusion plant to an external system for energy recovery. (LEW)

  13. Ion plated electronic tube device

    DOEpatents

    Meek, T.T.

    1983-10-18

    An electronic tube and associated circuitry which is produced by ion plating techniques. The process is carried out in an automated process whereby both active and passive devices are produced at very low cost. The circuitry is extremely reliable and is capable of functioning in both high radiation and high temperature environments. The size of the electronic tubes produced are more than an order of magnitude smaller than conventional electronic tubes.

  14. Alternate tube plugging criteria for steam generator tubes

    SciTech Connect

    Cueto-Felgueroso, C.; Aparicio, C.B.

    1997-02-01

    The tubing of the Steam Generators constitutes more than half of the reactor coolant pressure boundary. Specific requirements governing the maintenance of steam generator tubes integrity are set in Plant Technical Specifications and in Section XI of the ASME Boiler and Pressure Vessel Code. The operating experience of Steam Generator tubes of PWR plants has shown the existence of some types of degradatory processes. Every one of these has an specific cause and affects one or more zones of the tubes. In the case of Spanish Power Plants, and depending on the particular Plant considered, they should be mentioned the Primary Water Stress Corrosion Cracking (PWSCC) at the roll transition zone (RTZ), the Outside Diameter Stress Corrosion Cracking (ODSCC) at the Tube Support Plate (TSP) intersections and the fretting with the Anti-Vibration Bars (AVBs) or with the Support Plates in the preheater zone. The In-Service Inspections by Eddy Currents constitutes the standard method for assuring the SG tubes integrity and they permit the monitoring of the defects during the service life of the plant. When the degradation reaches a determined limit, called the plugging limit, the SG tube must be either repaired or retired from service by plugging. Customarily, the plugging limit is related to the depth of the defect. Such depth is typically 40% of the wall thickness of the tube and is applicable to any type of defect in the tube. In its origin, that limit was established for tubes thinned by wastage, which was the predominant degradation in the seventies. The application of this criterion for axial crack-like defects, as, for instance, those due to PWSCC in the roll transition zone, has lead to an excessive and unnecessary number of tubes being plugged. This has lead to the development of defect specific plugging criteria. Examples of the application of such criteria are discussed in the article.

  15. YouTube and 'psychiatry'.

    PubMed

    Gordon, Robert; Miller, John; Collins, Noel

    2015-12-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of 'psychiatry' during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of 'psychiatry' on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed.

  16. Reduced-vibration tube array

    DOEpatents

    Bruck, Gerald J.; Bartolomeo, Daniel R.

    2004-07-20

    A reduced-vibration tube array is disclosed. The array includes a plurality of tubes in a fixed arrangement and a plurality of damping members positioned within the tubes. The damping members include contoured interface regions characterized by bracing points that selectively contact the inner surface of an associated tube. Each interface region is sized and shaped in accordance with the associated tube, so that the damping member bracing points are spaced apart a vibration-reducing distance from the associated tube inner surfaces at equilibrium. During operation, mechanical interaction between the bracing points and the tube inner surfaces reduces vibration by a damage-reducing degree. In one embodiment, the interface regions are serpentine shaped. In another embodiment, the interface regions are helical in shape. The interface regions may be simultaneously helical and serpentine in shape. The damping members may be fixed within the associated tubes, and damping member may be customized several interference regions having attributes chosen in accordance with desired flow characteristics and associated tube properties.

  17. Electron tubes for industrial applications

    NASA Astrophysics Data System (ADS)

    Gellert, Bernd

    1994-05-01

    This report reviews research and development efforts within the last years for vacuum electron tubes, in particular power grid tubes for industrial applications. Physical and chemical effects are discussed that determine the performance of todays devices. Due to the progress made in the fundamental understanding of materials and newly developed processes the reliability and reproducibility of power grid tubes could be improved considerably. Modern computer controlled manufacturing methods ensure a high reproducibility of production and continuous quality certification according to ISO 9001 guarantees future high quality standards. Some typical applications of these tubes are given as an example.

  18. YouTube and 'psychiatry'.

    PubMed

    Gordon, Robert; Miller, John; Collins, Noel

    2015-12-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of 'psychiatry' during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of 'psychiatry' on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed. PMID:26755987

  19. Method for producing a tube

    DOEpatents

    Peterson, Kenneth A.; Rohde, Steven B.; Pfeifer, Kent B.; Turner, Timothy S.

    2007-01-02

    A method is described for producing tubular substrates having parallel spaced concentric rings of electrical conductors that can be used as the drift tube of an Ion Mobility Spectrometer (IMS). The invention comprises providing electrodes on the inside of a tube that are electrically connected to the outside of the tube through conductors that extend between adjacent plies of substrate that are combined to form the tube. Tubular substrates are formed from flexible polymeric printed wiring board materials, ceramic materials and material compositions of glass and ceramic, commonly known as Low Temperature Co-Fired Ceramic (LTCC). The adjacent plies are sealed together around the electrode.

  20. Learning from YouTube [Video Book

    ERIC Educational Resources Information Center

    Juhasz, Alexandra

    2011-01-01

    YouTube is a mess. YouTube is for amateurs. YouTube dissolves the real. YouTube is host to inconceivable combos. YouTube is best for corporate-made community. YouTube is badly baked. These are a few of the things Media Studies professor Alexandra Juhasz (and her class) learned about YouTube when she set out to investigate what actually happens…

  1. Infrared imaging of LED lighting tubes and fluorescent tubes

    NASA Astrophysics Data System (ADS)

    Siikanen, Sami; Kivi, Sini; Kauppinen, Timo; Juuti, Mikko

    2011-05-01

    The low energy efficiency of conventional light sources is mainly caused by generation of waste heat. We used infrared (IR) imaging in order to monitor the heating of both LED tube luminaires and ordinary T8 fluorescent tubes. The IR images showed clearly how the surface temperatures of the fluorescent tube ends quickly rose up to about +50...+70°C, whereas the highest surface temperatures seen on the LED tubes were only about +30...+40°C. The IR images demonstrated how the heat produced by the individual LED chips can be efficiently guided to the supporting structure in order to keep the LED emitters cool and hence maintain efficient operation. The consumed electrical power and produced illuminance were also recorded during 24 hour measurements. In order to assess the total luminous efficacy of the luminaires, separate luminous flux measurements were made in a large integrating sphere. The currently available LED tubes showed efficacies of up to 88 lm/W, whereas a standard "cool white" T8 fluorescent tube produced ca. 75 lm/W. Both lamp types gave ca. 110 - 130 lx right below the ceiling-mounted luminaire, but the LED tubes consume only 40 - 55% of the electric power compared to fluorescent tubes.

  2. Explosive welding of a tube into a tube sheet

    DOEpatents

    Green, Sheryll C.; Linse, Vonne D.

    1978-10-03

    A cartridge containing an explosive charge is placed within a tube assembled within a tube sheet. The charge is detonated through use of a detonator cord containing a minimum but effective amount of explosive material. The cord is contained inside a tubular shield throughout most of its length within the cartridge. A small length of the cord extends beyond the tubular shield to contact and detonate the explosive charge in its rear portion near the cartridge base. The cartridge base is provided of substantial mass and thickness in respect to side and front walls of the cartridge to minimize bulging beyond the rear face of the tube sheet. For remote activation an electrically activated detonator of higher charge density than the cord is attached to the cord at a location spaced from the tube sheet, cartridge and tube.

  3. Nasogastric tube syndrome induced by an indwelling long intestinal tube

    PubMed Central

    Sano, Naoki; Yamamoto, Masayoshi; Nagai, Kentaro; Yamada, Keiichi; Ohkohchi, Nobuhiro

    2016-01-01

    The nasogastric tube (NGT) has become a frequently used device to alleviate gastrointestinal symptoms. Nasogastric tube syndrome (NTS) is an uncommon but potentially life-threatening complication of an indwelling NGT. NTS is characterized by acute upper airway obstruction due to bilateral vocal cord paralysis. We report a case of a 76-year-old man with NTS, induced by an indwelling long intestinal tube. He was admitted to our hospital for treatment of sigmoid colon cancer. He underwent sigmoidectomy to release a bowel obstruction, and had a long intestinal tube inserted to decompress the intestinal tract. He presented acute dyspnea following prolonged intestinal intubation, and bronchoscopy showed bilateral vocal cord paralysis. The NGT was removed immediately, and tracheotomy was performed. The patient was finally discharged in a fully recovered state. NTS be considered in patients complaining of acute upper airway obstruction, not only with a NGT inserted but also with a long intestinal tube. PMID:27099450

  4. Nasogastric tube syndrome induced by an indwelling long intestinal tube.

    PubMed

    Sano, Naoki; Yamamoto, Masayoshi; Nagai, Kentaro; Yamada, Keiichi; Ohkohchi, Nobuhiro

    2016-04-21

    The nasogastric tube (NGT) has become a frequently used device to alleviate gastrointestinal symptoms. Nasogastric tube syndrome (NTS) is an uncommon but potentially life-threatening complication of an indwelling NGT. NTS is characterized by acute upper airway obstruction due to bilateral vocal cord paralysis. We report a case of a 76-year-old man with NTS, induced by an indwelling long intestinal tube. He was admitted to our hospital for treatment of sigmoid colon cancer. He underwent sigmoidectomy to release a bowel obstruction, and had a long intestinal tube inserted to decompress the intestinal tract. He presented acute dyspnea following prolonged intestinal intubation, and bronchoscopy showed bilateral vocal cord paralysis. The NGT was removed immediately, and tracheotomy was performed. The patient was finally discharged in a fully recovered state. NTS be considered in patients complaining of acute upper airway obstruction, not only with a NGT inserted but also with a long intestinal tube.

  5. Modelisation par elements finis du muscle strie

    NASA Astrophysics Data System (ADS)

    Leonard, Mathieu

    Ce present projet de recherche a permis. de creer un modele par elements finis du muscle strie humain dans le but d'etudier les mecanismes engendrant les lesions musculaires traumatiques. Ce modele constitue une plate-forme numerique capable de discerner l'influence des proprietes mecaniques des fascias et de la cellule musculaire sur le comportement dynamique du muscle lors d'une contraction excentrique, notamment le module de Young et le module de cisaillement de la couche de tissu conjonctif, l'orientation des fibres de collagene de cette membrane et le coefficient de poisson du muscle. La caracterisation experimentale in vitro de ces parametres pour des vitesses de deformation elevees a partir de muscles stries humains actifs est essentielle pour l'etude de lesions musculaires traumatiques. Le modele numerique developpe est capable de modeliser la contraction musculaire comme une transition de phase de la cellule musculaire par un changement de raideur et de volume a l'aide des lois de comportement de materiau predefinies dans le logiciel LS-DYNA (v971, Livermore Software Technology Corporation, Livermore, CA, USA). Le present projet de recherche introduit donc un phenomene physiologique qui pourrait expliquer des blessures musculaires courantes (crampes, courbatures, claquages, etc.), mais aussi des maladies ou desordres touchant le tissu conjonctif comme les collagenoses et la dystrophie musculaire. La predominance de blessures musculaires lors de contractions excentriques est egalement exposee. Le modele developpe dans ce projet de recherche met ainsi a l'avant-scene le concept de transition de phase ouvrant la porte au developpement de nouvelles technologies pour l'activation musculaire chez les personnes atteintes de paraplegie ou de muscles artificiels compacts pour l'elaboration de protheses ou d'exosquelettes. Mots-cles Muscle strie, lesion musculaire, fascia, contraction excentrique, modele par elements finis, transition de phase

  6. Drop tube technical tasks

    NASA Technical Reports Server (NTRS)

    Workman, G. L.

    1986-01-01

    Criteria, using fundamental thermochemical dynamics, were developed to assist a scientist using the Drop Tube Facility in designing a good experiment. The types of parameters involved in designing the experiments include the type of furnace, the type of atmosphere, and in general which materials are better behaved than others as determined by past experience in the facility. One of the major advantages of the facility lies in its ability to provide large undercoolings in the cooling curve during the drops. A beginning was to consider the effect of oxygen and other gases upon the amount of undercooling observed. The starting point of the thermochemistry was given by Ellingham and later transformed into what is known as the Richardson Chart. The effect of surface oxidations upon the nucleation phenomena can be observed in each specimen.

  7. Traveling wave tube circuit

    NASA Technical Reports Server (NTRS)

    Connolly, D. J. (Inventor)

    1978-01-01

    A traveling wave tube (TWT) has a slow wave structure (SWS) which is severed into two or more sections. A signal path, connects the end of an SWS section to the beginning of the following SWS section. The signal path comprises an impedance matching coupler (IMC), followed by an isolator, a variable phase shifter, and a second IMC. The aggregate band pass characteristic of the components in the signal path is chosen to reject, or strongly attenuate, all frequencies outside the desired operating frequency range of the TWT and yet pass, with minimal attenuation in the forward direction, all frequencies within the desired operating frequency range. The isolator is chosen to reject, or strongly attenuate, waves, of all frequencies, which propagate in the backward direction. The aggregate phase shift characteristic of the components in the signal path is chosen to apply signal power to the beginning of the following SWS section with the phase angle yielding maximum efficiency.

  8. Piezoelectric Rotary Tube Motor

    NASA Technical Reports Server (NTRS)

    Fisher, Charles D.; Badescu, Mircea; Braun, David F.; Culhane, Robert

    2011-01-01

    A custom rotary SQUIGGLE(Registered TradeMark) motor has been developed that sets new benchmarks for small motor size, high position resolution, and high torque without gear reduction. Its capabilities cannot be achieved with conventional electromagnetic motors. It consists of piezoelectric plates mounted on a square flexible tube. The plates are actuated via voltage waveforms 90 out of phase at the resonant frequency of the device to create rotary motion. The motors were incorporated into a two-axis postioner that was designed for fiber-fed spectroscopy for ground-based and space-based projects. The positioner enables large-scale celestial object surveys to take place in a practical amount of time.

  9. Forming tool improves quality of tubing flares

    NASA Technical Reports Server (NTRS)

    1966-01-01

    Punch and die set improves the quality of tubing flares for use with standard flared-tube fittings in high-pressure systems. It forges a dimensionally accurate flare in the tubing and forces more tubing material into the high-stress areas to improve the strength and tightness of the tubing connection.

  10. A Conserved Mode of Protein Recognition and Binding in a ParD−ParE Toxin−Antitoxin Complex

    SciTech Connect

    Dalton, Kevin M.; Crosson, Sean

    2010-05-06

    Toxin-antitoxin (TA) systems form a ubiquitous class of prokaryotic proteins with functional roles in plasmid inheritance, environmental stress response, and cell development. ParDE family TA systems are broadly conserved on plasmids and bacterial chromosomes and have been well characterized as genetic elements that promote stable plasmid inheritance. We present a crystal structure of a chromosomally encoded ParD-ParE complex from Caulobacter crescentus at 2.6 {angstrom} resolution. This TA system forms an {alpha}{sub 2}{beta}{sub 2} heterotetramer in the crystal and in solution. The toxin-antitoxin binding interface reveals extensive polar and hydrophobic contacts of ParD antitoxin helices with a conserved recognition and binding groove on the ParE toxin. A cross-species comparison of this complex structure with related toxin structures identified an antitoxin recognition and binding subdomain that is conserved between distantly related members of the RelE/ParE toxin superfamily despite a low level of overall primary sequence identity. We further demonstrate that ParD antitoxin is dimeric, stably folded, and largely helical when not bound to ParE toxin. Thus, the paradigmatic model in which antitoxin undergoes a disorder-to-order transition upon toxin binding does not apply to this chromosomal ParD-ParE TA system.

  11. Protease-activated receptor 1 (PAR1) signalling desensitization is counteracted via PAR4 signalling in human platelets.

    PubMed

    Fälker, Knut; Haglund, Linda; Gunnarsson, Peter; Nylander, Martina; Lindahl, Tomas L; Grenegård, Magnus

    2011-06-01

    PARs (protease-activated receptors) 1 and 4 belong to the family of G-protein-coupled receptors which induce both G(α12/13) and G(αq) signalling. By applying the specific PAR1- and PAR4-activating hexapeptides, SFLLRN and AYPGKF respectively, we found that aggregation of isolated human platelets mediated via PAR1, but not via PAR4, is abolished upon homologous receptor activation in a concentration- and time-dependent fashion. This effect was not due to receptor internalization, but to a decrease in Ca²⁺ mobilization, PKC (protein kinase C) signalling and α-granule secretion, as well as to a complete lack of dense granule secretion. Interestingly, subthreshold PAR4 activation rapidly abrogated PAR1 signalling desensitization by differentially reconstituting these affected signalling events and functional responses, which was sufficient to re-establish aggregation. The lack of ADP release and P2Y₁₂ receptor-induced G(αi) signalling accounted for the loss of the aggregation response, as mimicking G(αi/z) signalling with 2-MeS-ADP (2-methylthioadenosine-5'-O-diphosphate) or epinephrine (adrenaline) could substitute for intermediate PAR4 activation. Finally, we found that the re-sensitization of PAR1 signalling-induced aggregation via PAR4 relied on PKC-mediated release of both ADP from dense granules and fibrinogen from α-granules. The present study elucidates further differences in human platelet PAR signalling regulation and provides evidence for a cross-talk in which PAR4 signalling counteracts mechanisms involved in PAR1 signalling down-regulation. PMID:21391917

  12. Apical localization of ASIP/PAR-3:EGFP in zebrafish neuroepithelial cells involves the oligomerization domain CR1, the PDZ domains, and the C-terminal portion of the protein.

    PubMed

    von Trotha, Jakob W; Campos-Ortega, José A; Reugels, Alexander M

    2006-04-01

    Neurulation in zebrafish (Danio rerio) embryos is characterized by oriented cell divisions and the progressive establishment of cellular polarity. Mitoses in the neural plate and neural tube are planar, but in the neural keel/rod stage, the mitotic spindle rotates by 90 degrees, causing cell divisions to occur perpendicular to the plane of the neuroepithelium. The mechanisms and molecules that establish cellular polarity and cause the stereotypic orientation of the mitotic spindle during neurulation are largely unknown. In Caenorhabditis elegans and Drosophila, the PAR/aPKC complex has been shown to be involved in both establishment of cellular polarity and spindle orientation. Here, we show that the conserved N-terminal oligomerization domain (CR1) and the PDZ domains of ASIP/PAR-3:EGFP are involved in its localization to the apical membrane in zebrafish neuroepithelial cells. We further show that the C-terminal part of ASIP/PAR-3 contributes to proper localization and that the apical localization signals in ASIP/PAR-3 prevent the basolateral localization of a Numb:PAR-3 fusion protein. The parallel orientation of the mitotic spindle in the neural tube, however, is only weakly impaired upon overexpression of various ASIP/PAR-3:EGFP constructs.

  13. Apoptosis and Tumor Resistance Conferred by Par-4

    PubMed Central

    Zhao, Yanming; Rangnekar, Vivek M.

    2009-01-01

    Par-4 is a tumor suppressor protein with a pro-apoptotic function. Epigenetic silencing of Par-4 is seen in diverse tumors, and Par-4 knockout mice develop spontaneous tumors in various tissues. Endogenous Par-4 is essential for sensitization of cells to diverse apoptotic stimuli, whereas ectopic expression of Par-4 can selectively induce apoptosis in cancer cells. The cancer-specific pro-apoptotic action of Par-4 resides in its centrally located SAC domain. This chapter reviews a novel mouse model with ubiquitous expression of the SAC domain. These SAC transgenic mice display normal development and life span, and, most importantly, are resistant to spontaneous, as well as oncogene-induced, autochthonous tumors. The tumor resistant phenotype and undetectable toxicity of SAC in vivo suggests the SAC domain possesses tremendous therapeutic potential. PMID:18836307

  14. A new model for estimating boreal forest fPAR

    NASA Astrophysics Data System (ADS)

    Majasalmi, Titta; Rautiainen, Miina; Stenberg, Pauline

    2014-05-01

    Life on Earth is continuously sustained by the extraterrestrial flux of photosynthetically active radiation (PAR, 400-700 nm) from the sun. This flux is converted to biomass by chloroplasts in green vegetation. Thus, the fraction of absorbed PAR (fPAR) is a key parameter used in carbon balance studies, and is listed as one of the Essential Climate Variables (ECV). Temporal courses of fPAR for boreal forests are difficult to measure, because of the complex 3D structures. Thus, they are most often estimated based on models which quantify the dependency of absorbed radiation on canopy structure. In this study, we adapted a physically-based canopy radiation model into a fPAR model, and compared modeled and measured fPAR in structurally different boreal forest stands. The model is based on the spectral invariants theory, and uses leaf area index (LAI), canopy gap fractions and spectra of foliage and understory as input data. The model differs from previously developed more detailed fPAR models in that the complex 3D structure of coniferous forests is described using an aggregated canopy parameter - photon recollision probability p. The strength of the model is that all model inputs are measurable or available through other simple models. First, the model was validated with measurements of instantaneous fPAR obtained with the TRAC instrument in nine Scots pine, Norway spruce and Silver birch stands in a boreal forest in southern Finland. Good agreement was found between modeled and measured fPAR. Next, we applied the model to predict temporal courses of fPAR using data on incoming radiation from a nearby flux tower and sky irradiance models. Application of the model to simulate diurnal and seasonal values of fPAR indicated that the ratio of direct-to-total incident radiation and leaf area index are the key factors behind the magnitude and variation of stand-level fPAR values.

  15. 2. HI PAR (ACQUISITION RADAR) TOWER AND ENLISTED MEN (EM) ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. HI PAR (ACQUISITION RADAR) TOWER AND ENLISTED MEN (EM) BARRACKS WITH RADAR ATTACHED. - Nike Hercules Missile Battery Summit Site, Battery Control Administration & Barracks Building, Anchorage, Anchorage, AK

  16. Water-storage-tube systems. Final report

    SciTech Connect

    Hemker, P.

    1981-12-24

    Passive solar collection/storage/distribution systems were surveyed, designed, fabricated, and mechanically and thermally tested. The types studied were clear and opaque fiberglass tubes, metal tubes with plastic liners, and thermosyphoning tubes. (MHR)

  17. Eddy current signal comparison for tube identification

    SciTech Connect

    Glass, S. W. E-mail: Ratko.Vojvodic@areva.com; Vojvodic, R. E-mail: Ratko.Vojvodic@areva.com

    2015-03-31

    Inspection of nuclear power plant steam generator tubes is required to justify continued safe plant operation. The steam generators consist of thousands of tubes with nominal diameters of 15 to 22mm, approximately 1mm wall thickness, and 20 to 30m in length. The tubes are inspected by passing an eddy current probe through the tubes from tube end to tube end. It is critical to know exactly which tube identification (row and column) is associated with each tube's data. This is controlled by a precision manipulator that provides the tube ID to the eddy current system. Historically there have been some instances where the manipulator incorrectly reported the tube ID. This can have serious consequences including lack of inspection of a tube, or if a pluggable indication is detected, the tube is likely to be mis-plugged thereby risking a primary to secondary leak.

  18. Eddy current signal comparison for tube identification

    NASA Astrophysics Data System (ADS)

    Glass, S. W.; Vojvodic, R.

    2015-03-01

    Inspection of nuclear power plant steam generator tubes is required to justify continued safe plant operation. The steam generators consist of thousands of tubes with nominal diameters of 15 to 22mm, approximately 1mm wall thickness, and 20 to 30m in length. The tubes are inspected by passing an eddy current probe through the tubes from tube end to tube end. It is critical to know exactly which tube identification (row and column) is associated with each tube's data. This is controlled by a precision manipulator that provides the tube ID to the eddy current system. Historically there have been some instances where the manipulator incorrectly reported the tube ID. This can have serious consequences including lack of inspection of a tube, or if a pluggable indication is detected, the tube is likely to be mis-plugged thereby risking a primary to secondary leak.

  19. Vidicon storage tube electrical input/output

    NASA Technical Reports Server (NTRS)

    Lipoma, P.

    1972-01-01

    Electrical data storage tube is assembled from standard vidicon tube using conventional amplification and control circuits. Vidicon storage tube is simple, inexpensive and has an erase and preparation time of less than 5 microseconds.

  20. Flux tubes at finite temperature

    NASA Astrophysics Data System (ADS)

    Cea, Paolo; Cosmai, Leonardo; Cuteri, Francesca; Papa, Alessandro

    2016-06-01

    The chromoelectric field generated by a static quark-antiquark pair, with its peculiar tube-like shape, can be nicely described, at zero temperature, within the dual superconductor scenario for the QCD confining vacuum. In this work we investigate, by lattice Monte Carlo simulations of the SU (3) pure gauge theory, the fate of chromoelectric flux tubes across the deconfinement transition. We find that, if the distance between the static sources is kept fixed at about 0.76 fm˜eq 1.6/√{σ } and the temperature is increased towards and above the deconfinement temperature T c , the amplitude of the field inside the flux tube gets smaller, while the shape of the flux tube does not vary appreciably across deconfinement. This scenario with flux-tube "evaporation" above T c has no correspondence in ordinary (type-II) superconductivity, where instead the transition to the phase with normal conductivity is characterized by a divergent fattening of flux tubes as the transition temperature is approached from below. We present also some evidence about the existence of flux-tube structures in the magnetic sector of the theory in the deconfined phase.

  1. Tube wall temperature monitoring technique

    SciTech Connect

    Granton, R.L.

    1985-07-01

    In 1977, Monsanto and Conoco undertook the construction of a new, modern technology ethylene plant at Chocolate Bayou, near Alvin, Texas. This plant included high severity cracking furnaces with potential tube wall temperatures considerably higher than any we had previously experienced. Furnace on-stream time between decokes, a factor in the economics of plant operation, was limited by tube wall temperature, thus requiring its accurate knowledge. Earlier work with other ethylene furnaces had also demonstrated our lack of knowledge concerning high temperature measurements in a furnace firebox environment. This had to change. An outside consultant was called upon to provide a threeday workshop on radiant tube temperature sensing. The workshop consisted of two days of formal training in the theory and practice of temperature measurement and one day of field training. This workshop was conducted at a site away from the plant. Approximately 20 engineers (manufacturing and technical groups) attended. The major topics covered by this workshop are as follows: radiant tube temperature sensing, radiation situation of radiant tubes, g.a. method: sample calculations, noncontact sensors: methods of specifying and purchasing, thermal imager strategies, calibration of noncontact sensors, avoiding problems with noncontact sensors, optical aids to radiant tube viewing, tube temperature management and its environmental implications, and contact temperature sensors.

  2. Neural tube defects.

    PubMed

    Hasenau, Susan M; Covington, Chandice

    2002-01-01

    The purpose of this article is to describe the etiology of neural tube defects (NTDs) and the role of folic acid in their prevention. NTDs are all too common and devastating outcomes of many pregnancies. The brain and spinal cord malformations that develop during gestation in the NTD-affected pregnancies are expressed through various anomalies. Estimates by the Centers for Disease Control and Prevention (CDC) for 1995 reported over 4,000 occurrences of NTDs in the United States alone. Research has demonstrated that the preconception and prenatal addition of folic acid can greatly reduce the incidence of NTDs. Recent advances in genetic studies have increased awareness of the important role of folic acid in preventing NTDs. Identification of a genetic marker will allow for specific treatment of those women at high risk for NTDs. Despite recommendations from the CDC for folic acid supplementation, there is insufficient awareness of these guidelines by both the public and by healthcare providers. A National campaign to promote awareness of the role of folic acid in the prevention of NTDs has been initiated, and has been successful at reducing NTDs's by 19%. Nurses can be instrumental in the dissemination of information not only to women of childbearing age, but also to other nurses and physicians. PMID:11984276

  3. Assembly of carbon tube-in-tube nanostructures

    NASA Astrophysics Data System (ADS)

    Su, D. S.; Zhu, Z. P.; Liu, X.; Weinberg, G.; Wang, N.; Schlögl, R.

    2005-09-01

    Tube-in-tube carbon nanostructures were prepared by reorganization of graphitic impurity nanoparticles outside or inside of the pristine carbon nanotubes. Graphitic impurity nanoparticles were first disintegrated into small graphene fragments by a chemical oxidation with nitric acid, which also modifies the graphene fragments with carboxyl and hydroxyl groups at their edges. The functionalized graphene fragments were then reintegrated outside or inside of pristine carbon nanotubes to construct into tube-in-tube nanostructures. The combination of oxidatively functionalized graphene units, their solvate in a polar organic medium allowing for dispersive forces to effect supramolecular organization with carbon nanotubes acting as templates and their polycondensation by acid-catalysed esterification followed by pyrolysis of the oxygen functionalities lead to complex nanostructures inaccessible by direct synthesis.

  4. Acoustical studies on corrugated tubes

    NASA Astrophysics Data System (ADS)

    Balaguru, Rajavel

    Corrugated tubes and pipes offer greater global flexibility combined with local rigidity. They are used in numerous engineering applications such as vacuum cleaner hosing, air conditioning systems of aircraft and automobiles, HVAC control systems of heating ducts in buildings, compact heat exchangers, medical equipment and offshore gas and oil transportation flexible riser pipelines. Recently there has been a renewed research interest in analyzing the flow through a corrugated tube to understand the underlying mechanism of so called whistling, although the whistling in such a tube was identified in early twentieth century. The phenomenon of whistling in a corrugated tube is interesting because an airflow through a smooth walled tube of similar dimensions will not generate any whistling tones. Study of whistling in corrugated tubes is important because, it not only causes an undesirable noise problem but also results in flow-acoustic coupling. Such a coupling can cause significant structural vibrations due to flow-acoustic-structure interaction. This interaction would cause flow-induced vibrations that could result in severe damage to mechanical systems having corrugated tubes. In this research work, sound generation (whistling) in corrugated tubes due to airflow is analyzed using experimental as well as Computational Fluid Dynamics-Large Eddy Simulation (CFD-LES) techniques. Sound generation mechanisms resulting in whistling have been investigated. The whistling in terms of frequencies and sound pressure levels for different flow velocities are studied. The analytical and experimental studies are carried out to understand the influence of various parameters of corrugated tubes such as cavity length, cavity width, cavity depth, pitch, Reynolds numbers and number of corrugations. The results indicate that there is a good agreement between theoretically calculated, computationally predicted and experimentally measured whistling frequencies and sound pressure levels

  5. Expansion tube test time predictions

    NASA Technical Reports Server (NTRS)

    Gourlay, Christopher M.

    1988-01-01

    The interaction of an interface between two gases and strong expansion is investigated and the effect on flow in an expansion tube is examined. Two mechanisms for the unsteady Pitot-pressure fluctuations found in the test section of an expansion tube are proposed. The first mechanism depends on the Rayleigh-Taylor instability of the driver-test gas interface in the presence of a strong expansion. The second mechanism depends on the reflection of the strong expansion from the interface. Predictions compare favorably with experimental results. The theory is expected to be independent of the absolute values of the initial expansion tube filling pressures.

  6. PEG tubes: dealing with complications.

    PubMed

    Malhi, Hardip; Thompson, Rosie

    A percutaneous endoscopic gastronomy tube can be used to deliver nutrition, hydration and medicines directly into the patient's stomach. Patients will require a tube if they are unable to swallow safely, putting them at risk of aspiration of food, drink and medicines into their lungs. It is vital that nurses are aware of the complications that may arise when caring for a patient with a PEG tube. It is equally important that nurses know how to deal with these complications or from where tc seek advice. This article provides a quick troubleshooting guide to help nurses deal with complications that can arise with PEG feeding.

  7. Nonsteady Flow in Capillary Tubes

    NASA Astrophysics Data System (ADS)

    Hara, Ayako

    2000-03-01

    Surface phenomena in the field of electron devices and the problem of how long. It takes plants to absorb water during their growth in hydroponic cultivation is attraching the attention of riseachers. However, the related study of non-steady flow in capillary tubes has a number of issues that require investigation. In response to this situation, we made attempted to assess nonsteady fiow in capillary tubes, the liquid rise time and other issues, using a motion equation that takes factors including the friction force of the tube and the surface tension into consideration.

  8. Transcriptome profiling reveals links between ParS/ParR, MexEF-OprN, and quorum sensing in the regulation of adaptation and virulence in Pseudomonas aeruginosa

    PubMed Central

    2013-01-01

    Background The ParS/ParR two component regulatory system plays critical roles for multidrug resistance in Pseudomonas aeruginosa. It was demonstrated that in the presence of antimicrobials, ParR enhances bacterial survival by distinct mechanisms including activation of the mexXY efflux genes, enhancement of lipopolysaccharide modification through the arn operon, and reduction of the expression of oprD porin. Results In this study, we report on transcriptomic analyses of P. aeruginosa PAO1 wild type and parS and parR mutants growing in a defined minimal medium. Our transcriptomic analysis provides the first estimates of transcript abundance for the 5570 coding genes in P. aeruginosa PAO1. Comparative transcriptomics of P. aeruginosa PAO1 and par mutants identified a total of 464 genes regulated by ParS and ParR. Results also showed that mutations in the parS/parR system abolished expression of the mexEF-oprN operon by down-regulating the regulatory gene mexS. In addition to the known effects on drug resistance genes, transcript abundances of the quorum sensing genes (rhlIR and pqsABCDE-phnAB) were higher in both parS and parR mutants. In accordance with these results, a significant portion of the ParS/ParR regulated genes belonged to the MexEF-OprN and quorum sensing regulons. Deletion of the par genes also led to increased phenazine production and swarming motility, consistent with the up-regulation of the phenazine and rhamnolipid biosynthetic genes, respectively. Conclusion Our results link the ParS/ParR two component signal transduction system to MexEF-OprN and quorum sensing systems in P. aeruginosa. These results expand our understanding of the roles of the ParS/ParR system in the regulation of gene expression in P. aeruginosa, especially in the absence of antimicrobials. PMID:24034668

  9. Mechanism of DNA Segregation in Prokaryotes: Replicon Pairing by parC of Plasmid R1

    NASA Astrophysics Data System (ADS)

    Jensen, Rasmus Bugge; Lurz, Rudi; Gerdes, Kenn

    1998-07-01

    Prokaryotic chromosomes and plasmids encode partitioning systems that are required for DNA segregation at cell division. The systems are thought to be functionally analogous to eukaryotic centromeres and to play a general role in DNA segregation. The parA system of plasmid R1 encodes two proteins ParM and ParR, and a cis-acting centromere-like site denoted parC. The ParR protein binds to parC in vivo and in vitro. The ParM protein is an ATPase that interacts with ParR specifically bound to parC. Using electron microscopy, we show here that parC mediates efficient pairing of plasmid molecules. The pairing requires binding of ParR to parC and is stimulated by the ParM ATPase. The ParM mediated stimulation of plasmid pairing is dependent on ATP hydrolysis by ParM. Using a ligation kinetics assay, we find that ParR stimulates ligation of parC-containing DNA fragments. The rate-of-ligation was increased by wild type ParM protein but not by mutant ParM protein deficient in the ATPase activity. Thus, two independent assays show that parC mediates pairing of plasmid molecules in vitro. These results are consistent with the proposal that replicon pairing is part of the mechanism of DNA segregation in prokaryotes.

  10. Thermal stresses in composite tubes

    NASA Technical Reports Server (NTRS)

    Hyer, M. W.

    1986-01-01

    This paper summarizes work to determine the thermally-induced stresses and deformations in specially-constructed angle-ply composite tubes subjected to a uniform temperature change relative to their stress-free cure state. The tubes are designed for application to space structures and have high axial stiffness. Four angle-ply designs are examined in an effort to determine which design might have the most favorable thermally-induced response. A planar elasticity solution is used, the solution being valid away from the ends of the tube. Of the four designs considered, none has any particular advantage as far as stress levels are concerned. However, despite the fact that the tube wall is a balanced laminate, one design exhibits a significant amount of thermally-induced twist.

  11. Confined explosive joining of tubes

    NASA Technical Reports Server (NTRS)

    Bement, L. J.

    1979-01-01

    Technique uses explosive ribbon to join and seal tubes hermetically while totally confining explosive products, such as smoke, light, and sound. Only click is audible. Process yields joints of the same strengths as parent metal.

  12. Tube-wave seismic imaging

    DOEpatents

    Korneev, Valeri A [LaFayette, CA

    2009-05-05

    The detailed analysis of cross well seismic data for a gas reservoir in Texas revealed two newly detected seismic wave effects, recorded approximately 2000 feet above the reservoir. A tube-wave (150) is initiated in a source well (110) by a source (111), travels in the source well (110), is coupled to a geological feature (140), propagates (151) through the geological feature (140), is coupled back to a tube-wave (152) at a receiver well (120), and is and received by receiver(s) (121) in either the same (110) or a different receiving well (120). The tube-wave has been shown to be extremely sensitive to changes in reservoir characteristics. Tube-waves appear to couple most effectively to reservoirs where the well casing is perforated, allowing direct fluid contact from the interior of a well case to the reservoir.

  13. Tube-wave seismic imaging

    DOEpatents

    Korneev, Valeri A.; Bakulin, Andrey

    2009-10-13

    The detailed analysis of cross well seismic data for a gas reservoir in Texas revealed two newly detected seismic wave effects, recorded approximately 2000 feet above the reservoir. A tube-wave (150) is initiated in a source well (110) by a source (111), travels in the source well (110), is coupled to a geological feature (140), propagates (151) through the geological feature (140), is coupled back to a tube-wave (152) at a receiver well (120), and is and received by receiver(s) (121) in either the same (110) or a different receiving well (120). The tube-wave has been shown to be extremely sensitive to changes in reservoir characteristics. Tube-waves appear to couple most effectively to reservoirs where the well casing is perforated, allowing direct fluid contact from the interior of a well case to the reservoir.

  14. Proteases in agricultural dust induce lung inflammation through PAR-1 and PAR-2 activation.

    PubMed

    Romberger, Debra J; Heires, Art J; Nordgren, Tara M; Souder, Chelsea P; West, William; Liu, Xiang-de; Poole, Jill A; Toews, Myron L; Wyatt, Todd A

    2015-08-15

    Workers exposed to aerosolized dust present in concentrated animal feeding operations (CAFOs) are susceptible to inflammatory lung diseases, such as chronic obstructive pulmonary disease. Extracts of dust collected from hog CAFOs [hog dust extract (HDE)] are potent stimulators of lung inflammatory responses in several model systems. The observation that HDE contains active proteases prompted the present study, which evaluated the role of CAFO dust proteases in lung inflammatory processes and tested whether protease-activated receptors (PARs) are involved in the signaling pathway for these events. We hypothesized that the damaging proinflammatory effect of HDE is due, in part, to the proteolytic activation of PARs, and inhibiting the proteases in HDE or disrupting PAR activation would attenuate HDE-mediated inflammatory indexes in bronchial epithelial cells (BECs), in mouse lung slices in vitro, and in a murine in vivo exposure model. Human BECs and mouse lung slice cultures stimulated with 5% HDE released significantly more of each of the cytokines measured (IL-6, IL-8, TNF-α, keratinocyte-derived chemokine/CXC chemokine ligand 1, and macrophage inflammatory protein-2/CXC chemokine ligand 2) than controls, and these effects were markedly diminished by protease inhibition. Inhibition of PARs also blunted the HDE-induced cytokine release from BECs. In addition, protease depletion inhibited HDE-induced BEC intracellular PKCα and PKCε activation. C57BL/6J mice administered 12.5% HDE intranasally, either once or daily for 3 wk, exhibited increased total cellular and neutrophil influx, bronchial alveolar fluid inflammatory cytokines, lung histopathology, and inflammatory scores compared with mice receiving protease-depleted HDE. These data suggest that proteases in dust from CAFOs are important mediators of lung inflammation, and these proteases and their receptors may provide novel targets for therapeutic intervention in CAFO dust-induced airways disease.

  15. Proteases in agricultural dust induce lung inflammation through PAR-1 and PAR-2 activation.

    PubMed

    Romberger, Debra J; Heires, Art J; Nordgren, Tara M; Souder, Chelsea P; West, William; Liu, Xiang-de; Poole, Jill A; Toews, Myron L; Wyatt, Todd A

    2015-08-15

    Workers exposed to aerosolized dust present in concentrated animal feeding operations (CAFOs) are susceptible to inflammatory lung diseases, such as chronic obstructive pulmonary disease. Extracts of dust collected from hog CAFOs [hog dust extract (HDE)] are potent stimulators of lung inflammatory responses in several model systems. The observation that HDE contains active proteases prompted the present study, which evaluated the role of CAFO dust proteases in lung inflammatory processes and tested whether protease-activated receptors (PARs) are involved in the signaling pathway for these events. We hypothesized that the damaging proinflammatory effect of HDE is due, in part, to the proteolytic activation of PARs, and inhibiting the proteases in HDE or disrupting PAR activation would attenuate HDE-mediated inflammatory indexes in bronchial epithelial cells (BECs), in mouse lung slices in vitro, and in a murine in vivo exposure model. Human BECs and mouse lung slice cultures stimulated with 5% HDE released significantly more of each of the cytokines measured (IL-6, IL-8, TNF-α, keratinocyte-derived chemokine/CXC chemokine ligand 1, and macrophage inflammatory protein-2/CXC chemokine ligand 2) than controls, and these effects were markedly diminished by protease inhibition. Inhibition of PARs also blunted the HDE-induced cytokine release from BECs. In addition, protease depletion inhibited HDE-induced BEC intracellular PKCα and PKCε activation. C57BL/6J mice administered 12.5% HDE intranasally, either once or daily for 3 wk, exhibited increased total cellular and neutrophil influx, bronchial alveolar fluid inflammatory cytokines, lung histopathology, and inflammatory scores compared with mice receiving protease-depleted HDE. These data suggest that proteases in dust from CAFOs are important mediators of lung inflammation, and these proteases and their receptors may provide novel targets for therapeutic intervention in CAFO dust-induced airways disease. PMID

  16. Proteases in agricultural dust induce lung inflammation through PAR-1 and PAR-2 activation

    PubMed Central

    Heires, Art J.; Nordgren, Tara M.; Souder, Chelsea P.; West, William; Liu, Xiang-de; Poole, Jill A.; Toews, Myron L.; Wyatt, Todd A.

    2015-01-01

    Workers exposed to aerosolized dust present in concentrated animal feeding operations (CAFOs) are susceptible to inflammatory lung diseases, such as chronic obstructive pulmonary disease. Extracts of dust collected from hog CAFOs [hog dust extract (HDE)] are potent stimulators of lung inflammatory responses in several model systems. The observation that HDE contains active proteases prompted the present study, which evaluated the role of CAFO dust proteases in lung inflammatory processes and tested whether protease-activated receptors (PARs) are involved in the signaling pathway for these events. We hypothesized that the damaging proinflammatory effect of HDE is due, in part, to the proteolytic activation of PARs, and inhibiting the proteases in HDE or disrupting PAR activation would attenuate HDE-mediated inflammatory indexes in bronchial epithelial cells (BECs), in mouse lung slices in vitro, and in a murine in vivo exposure model. Human BECs and mouse lung slice cultures stimulated with 5% HDE released significantly more of each of the cytokines measured (IL-6, IL-8, TNF-α, keratinocyte-derived chemokine/CXC chemokine ligand 1, and macrophage inflammatory protein-2/CXC chemokine ligand 2) than controls, and these effects were markedly diminished by protease inhibition. Inhibition of PARs also blunted the HDE-induced cytokine release from BECs. In addition, protease depletion inhibited HDE-induced BEC intracellular PKCα and PKCε activation. C57BL/6J mice administered 12.5% HDE intranasally, either once or daily for 3 wk, exhibited increased total cellular and neutrophil influx, bronchial alveolar fluid inflammatory cytokines, lung histopathology, and inflammatory scores compared with mice receiving protease-depleted HDE. These data suggest that proteases in dust from CAFOs are important mediators of lung inflammation, and these proteases and their receptors may provide novel targets for therapeutic intervention in CAFO dust-induced airways disease. PMID

  17. Photomultiplier tube gain regulating system

    DOEpatents

    Johnson, Wayne F.

    1976-01-01

    This invention relates to an improved system for regulating the gain of a photomultiplier tube, and was designed for use with the photomultiplier tubes of a GeMSAEC fast analyzers. It has the following advantages over the prior system: noise is virtually eliminated; sample analysis can begin after 3 to 4 revolutions of the rotor; fluorescent and light scattering solutions can be used as a reference; and the reference solution can be in any cuvette on the rotor.

  18. Duplication of the fallopian tube

    PubMed Central

    R, Narayanan; MA, Rajeev

    2008-01-01

    Hysterosalpingography accurately delineates the uterine and tubal lumen, and hence is routinely performed for the evaluation of infertility.We observed a case of infertility where uterine cavity was normal but fallopian tubes were bifurcated at the ampullary region. Mullerian duct anomalies are reported in literature, but maldevelopment of fallopian tube in isolation is rare. This abnormality can present as infertility, ectopic pregnancy, in association with urinary tract anomalies or as failure of sterilisation method. PMID:19562063

  19. Dermatology on YouTube.

    PubMed

    Boyers, Lindsay N; Quest, Tyler; Karimkhani, Chante; Connett, Jessica; Dellavalle, Robert P

    2014-06-01

    YouTube, reaches upwards of six billion users on a monthly basis and is a unique source of information distribution and communication. Although the influence of YouTube on personal health decision-making is well established, this study assessed the type of content and viewership on a broad scope of dermatology related content on YouTube. Select terms (i.e. dermatology, sun protection, skin cancer, skin cancer awareness, and skin conditions) were searched on YouTube. Overall, the results included 100 videos with over 47 million viewers. Advocacy was the most prevalent content type at 24% of the total search results. These 100 videos were "shared" a total of 101,173 times and have driven 6,325 subscriptions to distinct YouTube user pages. Of the total videos, 35% were uploaded by or featured an MD/DO/PhD in dermatology or other specialty/field, 2% FNP/PA, 1% RN, and 62% other. As one of the most trafficked global sites on the Internet, YouTube is a valuable resource for dermatologists, physicians in other specialties, and the general public to share their dermatology-related content and gain subscribers. However, challenges of accessing and determining evidence-based data remain an issue.

  20. Tube wall thickness measurement apparatus

    DOEpatents

    Lagasse, Paul R.

    1987-01-01

    An apparatus for measuring the thickness of a tube's wall for the tube's entire length and circumference by determining the deviation of the tube wall thickness from the known thickness of a selected standard item. The apparatus comprises a base and a first support member having first and second ends. The first end is connected to the base and the second end is connected to a spherical element. A second support member is connected to the base and spaced apart from the first support member. A positioning element is connected to and movable relative to the second support member. An indicator is connected to the positioning element and is movable to a location proximate the spherical element. The indicator includes a contact ball for first contacting the selected standard item and holding it against the spherical element. The contact ball then contacts the tube when the tube is disposed about the spherical element. The indicator includes a dial having a rotatable needle for indicating the deviation of the tube wall thickness from the thickness of the selected standard item.

  1. Tube wall thickness measurement apparatus

    DOEpatents

    Lagasse, P.R.

    1985-06-21

    An apparatus for measuring the thickness of a tube's wall for the tube's entire length and radius by determining the deviation of the tube wall thickness from the known thickness of a selected standard item. The apparatus comprises a base and a first support member having first and second ends. The first end is connected to the base and the second end is connected to a spherical element. A second support member is connected to the base and spaced apart from the first support member. A positioning element is connected to and movable relative to the second support member. An indicator is connected to the positioning element and is movable to a location proximate the spherical element. The indicator includes a contact ball for first contacting the selected standard item and holding it against the spherical element. The contact ball then contacts the tube when the tube is disposed about the spherical element. The indicator includes a dial having a rotatable needle for indicating the deviation of the tube wall thickness from the thickness of the selected standard item.

  2. SPRY1 promotes the degradation of uPAR and inhibits uPAR-mediated cell adhesion and proliferation

    PubMed Central

    Liu, Xiufeng; Lan, Yan; Zhang, Di; Wang, Kai; Wang, Yao; Hua, Zi-Chun

    2014-01-01

    Urokinase plasminogen activator receptor (uPAR) is a GPI anchored cell surface protein that is closely associated with invasion, migration, and metastasis of cancer cells. Many functional extracellular proteins and transmembrane receptors interact with uPAR. However, few studies have examined the association of uPAR with cytoplasm proteins. We previously used yeast two-hybrid screening to isolate several novel uPAR-interacting cytoplasmic proteins, including Sprouty1 (SPRY1), an inhibitor of the (Ras-mitogen-activated protein kinase) MAPK pathway. In this study, we show that SPRY1 interacts with uPAR and directs it toward lysosomal-mediated degradation. Overexpression of SPRY1 decreased the cell surface and cytoplasmic uPAR protein level. Moreover, SPRY1 overexpression augmented uPAR-induced cell adhesion to vitronectin as well as proliferation of cancer cells. Our results also further support the critical role of SPRY1 contribution to tumor growth. In a subcutaneous tumor model, overexpression of SPRY1 in HCT116 or A549 xenograft in athymic nude mice led to great suppression of tumor growth. These results show that SPRY1 may affect tumor cell function through direct interaction with uPAR and promote its lysosomal degradation. PMID:25520860

  3. Megestrol acetate NCD oral suspension--Par Pharmaceutical: megestrol acetate nanocrystal dispersion oral suspension, PAR 100.2, PAR-100.2.

    PubMed

    2007-01-01

    Par Pharmaceutical has developed megestrol acetate (Megace ES) oral suspension for the treatment of anorexia, cachexia and a significant weight loss associated with AIDS. Par Pharmaceutical used Elan Corporation's NanoCrystal Dispersion (NCD) technology to develop an advanced, concentrated formulation of megestrol acetate with improved bioavailability, more rapid onset of action, more convenient dosing and a lower dosing regimen compared with the original marketed formulation of megestrol acetate oral suspension. Patients are administered a teaspoon (5mL) of the new NCD formulation once daily, compared with a daily 20mL dosage cup of the original formulation. The new megestrol acetate NCD formulation represents a line-extension of Par's megestrol acetate oral suspension (800mg/20mL, Megace O/S) that has been marketed for anorexia, cachexia and AIDS-related weight loss since July 2001. Par's megestrol acetate is the generic version of Bristol-Myers Squibb's Megace Oral Suspension. NanoCrystal Dispersion (NCD) is a trademark of Elan Corporation. Par Pharmaceutical will market megestol acetate NCD oral suspension under the Megace brand name. The company licensed the Megace name from Bristol-Myers Squib in August 2003. The US FDA approved megestrol acetate oral suspension (625 mg/mL) in July 2005 for the treatment of anorexia, cachexia or a significant, unexplained weight loss in patients with AIDS. The NDA for the product was accepted for review by the agency in September 2004, following its submission in June of that year.Par Pharmaceutical commenced the first of two phase III clinical trials of megestrol acetate oral suspension (PAR 100.2) in cancer-induced anorexia in the first quarter of 2006. However, this trial was discontinued in September 2006 because of slow patient enrolment. The company intends to discuss future development options in this indication with the FDA.New formulations or dosage forms of megestrol acetate concentrated suspension are also in

  4. Megestrol acetate NCD oral suspension -- Par Pharmaceutical: megestrol acetate nanocrystal dispersion oral suspension, PAR 100.2, PAR-100.2.

    PubMed

    2007-01-01

    Par Pharmaceutical has developed megestrol acetate (Megace ES) oral suspension for the treatment of anorexia, cachexia and a significant weight loss associated with AIDS. Par Pharmaceutical used Elan Corporation's NanoCrystal Dispersion (NCD) technology to develop an advanced, concentrated formulation of megestrol acetate with improved bioavailability, more rapid onset of action, more convenient dosing and a lower dosing regimen compared with the original marketed formulation of megestrol acetate oral suspension. Patients are administered a teaspoon (5mL) of the new NCD formulation once daily, compared with a daily 20mL dosage cup of the original formulation. The new megestrol acetate NCD formulation represents a line-extension of Par's megestrol acetate oral suspension (800mg/20mL, Megace O/S) that has been marketed for anorexia, cachexia and AIDS-related weight loss since July 2001. Par's megestrol acetate is the generic version of Bristol-Myers Squibb's Megace Oral Suspension. NanoCrystal Dispersion (NCD) is a trademark of Elan Corporation. Par Pharmaceutical will market megestol acetate NCD oral suspension under the Megace brand name. The company licensed the Megace name from Bristol-Myers Squib in August 2003. The US FDA approved megestrol acetate oral suspension (625 mg/mL) in July 2005 for the treatment of anorexia, cachexia or a significant, unexplained weight loss in patients with AIDS. The NDA for the product was accepted for review by the agency in September 2004, following its submission in June of that year.Par Pharmaceutical commenced the first of two phase III clinical trials of megestrol acetate oral suspension (PAR 100.2) in cancer-induced anorexia in the first quarter of 2006. However, this trial was discontinued in September 2006 because of slow patient enrolment. The company intends to discuss future development options in this indication with the FDA.New formulations or dosage forms of megestrol acetate concentrated suspension are also in

  5. 21 CFR 872.6570 - Impression tube.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Impression tube. 872.6570 Section 872.6570 Food... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single...

  6. 21 CFR 868.5720 - Bronchial tube.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Bronchial tube. 868.5720 Section 868.5720 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5720 Bronchial tube. (a) Identification. A bronchial tube is a... leading directly to the lung) in order to isolate a portion of lung distal to the tube. (b)...

  7. 21 CFR 868.5720 - Bronchial tube.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Bronchial tube. 868.5720 Section 868.5720 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5720 Bronchial tube. (a) Identification. A bronchial tube is a... leading directly to the lung) in order to isolate a portion of lung distal to the tube. (b)...

  8. 21 CFR 872.6570 - Impression tube.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Impression tube. 872.6570 Section 872.6570 Food... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single...

  9. 21 CFR 868.5720 - Bronchial tube.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Bronchial tube. 868.5720 Section 868.5720 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5720 Bronchial tube. (a) Identification. A bronchial tube is a... leading directly to the lung) in order to isolate a portion of lung distal to the tube. (b)...

  10. 21 CFR 872.6570 - Impression tube.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Impression tube. 872.6570 Section 872.6570 Food... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single...

  11. 27 CFR 41.35 - Cigarette tubes.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2013-04-01 2013-04-01 false Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following...

  12. 27 CFR 40.352 - Cigarette tubes.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2011-04-01 2011-04-01 false Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette...

  13. 27 CFR 41.35 - Cigarette tubes.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2011-04-01 2011-04-01 false Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following...

  14. 21 CFR 872.6570 - Impression tube.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Impression tube. 872.6570 Section 872.6570 Food... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single...

  15. 27 CFR 40.352 - Cigarette tubes.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2012-04-01 2011-04-01 true Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette...

  16. 27 CFR 40.352 - Cigarette tubes.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2014-04-01 2014-04-01 false Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette...

  17. 27 CFR 40.352 - Cigarette tubes.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2013-04-01 2013-04-01 false Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette...

  18. 21 CFR 868.5720 - Bronchial tube.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Bronchial tube. 868.5720 Section 868.5720 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5720 Bronchial tube. (a) Identification. A bronchial tube is a... leading directly to the lung) in order to isolate a portion of lung distal to the tube. (b)...

  19. 27 CFR 40.352 - Cigarette tubes.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Cigarette tubes. 40.352... OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Manufacture of Cigarette Papers and Tubes Taxes § 40.352 Cigarette tubes. Cigarette...

  20. 27 CFR 41.35 - Cigarette tubes.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2014-04-01 2014-04-01 false Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following...

  1. 21 CFR 872.6570 - Impression tube.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Impression tube. 872.6570 Section 872.6570 Food... DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6570 Impression tube. (a) Identification. An impression tube is a device consisting of a hollow copper tube intended to take an impression of a single...

  2. 27 CFR 41.35 - Cigarette tubes.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2012-04-01 2011-04-01 true Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following...

  3. 21 CFR 868.5720 - Bronchial tube.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bronchial tube. 868.5720 Section 868.5720 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5720 Bronchial tube. (a) Identification. A bronchial tube is a... leading directly to the lung) in order to isolate a portion of lung distal to the tube. (b)...

  4. 27 CFR 41.35 - Cigarette tubes.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Cigarette tubes. 41.35... OF THE TREASURY (CONTINUED) TOBACCO IMPORTATION OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Taxes Tax Rates § 41.35 Cigarette tubes. Cigarette tubes are taxed at the following...

  5. Gage tests tube flares quickly and accurately

    NASA Technical Reports Server (NTRS)

    Griffin, F. D.

    1966-01-01

    Flared tube gage with a test cone that is precisely made with a tapering surface to complement the tube flare is capable of determining the accuracy of a tube flare efficiently and economically. This device should improve the speed, efficiency, and accuracy of tube flare inspections.

  6. Control of cleavage spindle orientation in Caenorhabditis elegans: The role of the genes par-2 and par-3

    SciTech Connect

    Cheng, N.N.; Kirby, C.M.; Kemphues, K.J.

    1995-02-01

    Polarized asymmetric divisions play important roles in the development of plants and animals. The first two embryonic cleavages of Caenorhabditis elegans provide an opportunity to study the mechanisms controlling polarized asymmetric divisions. The first cleavage is unequal, producing daughters with different sizes and fates. The daughter blastomeres divide with different orientations at the second cleavage; the anterior blastomere divides equally across the long axis of the egg, whereas the posterior blastomere divides unequally along the long axis. We report here the results of our analysis of the genes par-2 and par-3 with respect to their contribution to the polarity of these divisions. Strong loss-of-function mutations in both genes lead to an equal first cleavage and an altered second cleavage. Interestingly, the mutations exhibit striking gene-specific differences at the second cleavage. The par-2 mutations lead to transverse spindle orientations in both blastomeres, whereas par-3 mutations lead to longitudinal spindle orientations in both blastomeres. The spindle orientation defects correlate with defects in centrosome movements during both the first and the second cell cycle. Temperature shift experiments with par-2 (it5ts) indicate that the par-2(+) activity is not required after the two-cell stage. Analysis of double mutants shows that par-3 is epistatic to par-2. We propose a model wherein par-2(+) and par-3(+) act in concert during the first cell cycle to affect asymmetric modification of the cytoskeleton. This polar modification leads to different behaviors of centrosomes in the anterior and posterior and leads ultimately to blastomere-specific spindle orientations at the second cleavage. 44 refs., 5 figs., 5 tabs.

  7. Scleral Buckling for Rhegmatogenous Retinal Detachment Associated with Pars Planitis

    PubMed Central

    Ahn, Jae Kyoun

    2016-01-01

    Purpose. To evaluate the surgical outcome of scleral buckling (SB) in rhegmatogenous retinal detachment (RRD) patients associated with pars planitis. Methods. Retrospective review of RRD patients (32 eyes of pars planitis RRD and 180 eyes of primary RRD) who underwent SB. We compared primary and final anatomical success rates and visual outcomes between two groups. Results. Primary and final anatomical success were achieved in 25 (78.1%) and 31 (96.8%) eyes in the pars planitis RRD group and in 167 eyes (92.7%) and 176 eyes (97.7%) in primary RRD group, respectively. Both groups showed significant visual improvement (p < 0.001) and there were no significant differences in final visual acuity. Pars planitis RRD group was associated with higher rate of postoperative proliferative vitreoretinopathy (PVR) development (12.5% versus 2.8%, p = 0.031). Pars planitis and high myopia were significant preoperative risk factors and pseudophakia was borderline risk for primary anatomical failure after adjusting for various clinical factors. Conclusions. Pars planitis associated RRD showed inferior primary anatomical outcome after SB due to postoperative PVR development. However, final anatomical and visual outcomes were favorable. RRD cases associated with pars planitis, high myopia, and pseudophakia might benefit from different surgical approaches, such as combined vitrectomy and SB. PMID:27688907

  8. Scleral Buckling for Rhegmatogenous Retinal Detachment Associated with Pars Planitis.

    PubMed

    Kim, Yong-Kyu; Yoon, Wontae; Ahn, Jae Kyoun; Park, Sung Pyo

    2016-01-01

    Purpose. To evaluate the surgical outcome of scleral buckling (SB) in rhegmatogenous retinal detachment (RRD) patients associated with pars planitis. Methods. Retrospective review of RRD patients (32 eyes of pars planitis RRD and 180 eyes of primary RRD) who underwent SB. We compared primary and final anatomical success rates and visual outcomes between two groups. Results. Primary and final anatomical success were achieved in 25 (78.1%) and 31 (96.8%) eyes in the pars planitis RRD group and in 167 eyes (92.7%) and 176 eyes (97.7%) in primary RRD group, respectively. Both groups showed significant visual improvement (p < 0.001) and there were no significant differences in final visual acuity. Pars planitis RRD group was associated with higher rate of postoperative proliferative vitreoretinopathy (PVR) development (12.5% versus 2.8%, p = 0.031). Pars planitis and high myopia were significant preoperative risk factors and pseudophakia was borderline risk for primary anatomical failure after adjusting for various clinical factors. Conclusions. Pars planitis associated RRD showed inferior primary anatomical outcome after SB due to postoperative PVR development. However, final anatomical and visual outcomes were favorable. RRD cases associated with pars planitis, high myopia, and pseudophakia might benefit from different surgical approaches, such as combined vitrectomy and SB. PMID:27688907

  9. Scleral Buckling for Rhegmatogenous Retinal Detachment Associated with Pars Planitis

    PubMed Central

    Ahn, Jae Kyoun

    2016-01-01

    Purpose. To evaluate the surgical outcome of scleral buckling (SB) in rhegmatogenous retinal detachment (RRD) patients associated with pars planitis. Methods. Retrospective review of RRD patients (32 eyes of pars planitis RRD and 180 eyes of primary RRD) who underwent SB. We compared primary and final anatomical success rates and visual outcomes between two groups. Results. Primary and final anatomical success were achieved in 25 (78.1%) and 31 (96.8%) eyes in the pars planitis RRD group and in 167 eyes (92.7%) and 176 eyes (97.7%) in primary RRD group, respectively. Both groups showed significant visual improvement (p < 0.001) and there were no significant differences in final visual acuity. Pars planitis RRD group was associated with higher rate of postoperative proliferative vitreoretinopathy (PVR) development (12.5% versus 2.8%, p = 0.031). Pars planitis and high myopia were significant preoperative risk factors and pseudophakia was borderline risk for primary anatomical failure after adjusting for various clinical factors. Conclusions. Pars planitis associated RRD showed inferior primary anatomical outcome after SB due to postoperative PVR development. However, final anatomical and visual outcomes were favorable. RRD cases associated with pars planitis, high myopia, and pseudophakia might benefit from different surgical approaches, such as combined vitrectomy and SB.

  10. Multi-scale photoacoustic remote sensing (PARS) (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Haji Reza, Parsin; Bell, Kevan; Shi, W.; Zemp, Roger J.

    2016-03-01

    We introduce a novel multi-scale photoacoustic remote sensing (PARS) imaging system. Our system can provide optical resolution details for superficial structures as well as acoustic resolution for deep-tissue imaging down to 5 cm, in a non-contact setting. PARS system does not require any contact with the sample or ultrasound coupling medium. The optical resolution PARS (OR-OARS) system uses optically focused pulsed excitation with optical detection of photoacoustic signatures using a long-coherence interrogation beam co-focused and co-scanned with the excitation spot. In the OR-PARS initial pressures are sampled right at their subsurface origin where acoustic pressures are largest. The Acoustic resolution PARS (AR-PARS) picks up the surface oscillation of the tissue caused by generated photoacoustic signal using a modified version of Michelson interferometry. By taking advantage of 4-meters polarization maintaining single-mode fiber and a green fiber laser we have generated a multi-wavelength source using stimulated Raman scattering. Remote functional imaging using this multi-wavelength excitation source and PARS detection mechanism has been demonstrated. The oxygen saturation estimations are shown for both phantom and in vivo studies. Images of blood vessel structures for an In vivo chicken embryo model is demonstrated. The Phantom studies indicates ~3µm and ~300µm lateral resolution for OR-PARS and AR-PARS respectively. To the best of our knowledge this is the first dual modality non-contact optical and acoustic resolution system used for in vivo imaging.

  11. Laser initiated endotracheal tube explosion.

    PubMed

    De Vane, G G

    1990-06-01

    A 62-year-old male with a diagnosis of subglottic and tracheal stenosis resulting from a prolonged intubation was scheduled for a laser bronchoscopy and placement of a silicon T-shaped tube. His history was significant for two myocardial infarctions, an episode of congestive heart failure and exertional angina. A 6 mm polyvinyl chloride endotracheal tube, wrapped with aluminum tape, was placed in an existing tracheostomy stoma. During the course of the procedure, a sudden bright flash occurred followed by an explosive noise and black smoke rising in the anesthesia circuit and from the patient's mouth. The endotracheal tube was removed and the patient was treated for first and second degree burns in the supraglottic area and base of the tongue. In laser surgery of the airway, special care should be given to reducing the flammability of the inspired gases which can be best accomplished by the mixture of helium with oxygen. Helium acts to retard ignition of polyvinyl chloride tubes in concentrations of 60% or greater. The external surface of the tube can also be protected with the application of a metallic tape affixed in a spiral fashion. Finally, a protocol for the management and treatment of this emergency should be adopted and rehearsed. PMID:2378234

  12. Superluminal subway: The Krasnikov tube

    NASA Astrophysics Data System (ADS)

    Everett, Allen E.; Roman, Thomas A.

    1997-08-01

    The ``warp drive'' metric recently presented by Alcubierre has the problem that an observer at the center of the warp bubble is causally separated from the outer edge of the bubble wall. Hence such an observer can neither create a warp bubble on demand nor control one once it has been created. In addition, such a bubble requires negative energy densities. One might hope that elimination of the first problem might ameliorate the second as well. We analyze and generalize a metric, originally proposed by Krasnikov for two spacetime dimensions, which does not suffer from the first difficulty. As a consequence, the Krasnikov metric has the interesting property that, although the time for a one-way trip to a distant star cannot be shortened, the time for a round trip, as measured by clocks on Earth, can be made arbitrarily short. In our four-dimensional extension of this metric, a ``tube'' is constructed along the path of an outbound spaceship, which connects the Earth and the star. Inside the tube spacetime is flat, but the light cones are opened out so as to allow superluminal travel in one direction. We show that, although a single Krasnikov tube does not involve closed timelike curves, a time machine can be constructed with a system of two nonoverlapping tubes. Furthermore, it is demonstrated that Krasnikov tubes, like warp bubbles and traversable wormholes, also involve unphysically thin layers of negative energy density, as well as large total negative energies, and, therefore, probably cannot be realized in practice.

  13. Limnological database for Par Pond: 1959 to 1980

    SciTech Connect

    Tilly, L.J.

    1981-03-01

    A limnological database for Par Pond, a cooling reservoir for hot reactor effluent water at the Savannah River Plant, is described. The data are derived from a combination of research and monitoring efforts on Par Pond since 1959. The approximately 24,000-byte database provides water quality, primary productivity, and flow data from a number of different stations, depths, and times during the 22-year history of the Par Pond impoundment. The data have been organized to permit an interpretation of the effects of twenty years of cooling system operations on the structure and function of an aquatic ecosystem.

  14. Predicted PAR1 inhibitors from multiple computational methods

    NASA Astrophysics Data System (ADS)

    Wang, Ying; Liu, Jinfeng; Zhu, Tong; Zhang, Lujia; He, Xiao; Zhang, John Z. H.

    2016-08-01

    Multiple computational approaches are employed in order to find potentially strong binders of PAR1 from the two molecular databases: the Specs database containing more than 200,000 commercially available molecules and the traditional Chinese medicine (TCM) database. By combining the use of popular docking scoring functions together with detailed molecular dynamics simulation and protein-ligand free energy calculations, a total of fourteen molecules are found to be potentially strong binders of PAR1. The atomic details in protein-ligand interactions of these molecules with PAR1 are analyzed to help understand the binding mechanism which should be very useful in design of new drugs.

  15. An electromagnetic PIC code on the MasPar

    SciTech Connect

    MacNeice, P.

    1993-12-31

    A 3D electromagnetic particle-in-cell code has been rewritten to run on the MasPar. The original code; known as TRISTAN which was written by Oscar Buneman was rewritten in MPL and its data structure altered to suit the MasPar architecture and exploit the fully local property of the algorithm. We discuss the significant issues associated with porting the code and present a comparative analysis of the code run times on the MasPar and on the CRAY YMP and C90. Results of a simulation of the interaction of the solar wind with the earth`s magnetosphere are shown.

  16. Protease-Activated Receptor (PAR)2, but Not PAR1, Is Involved in Collateral Formation and Anti-Inflammatory Monocyte Polarization in a Mouse Hind Limb Ischemia Model

    PubMed Central

    Nossent, Anne Yael; van Oeveren-Rietdijk, Annemarie M.; de Vries, Margreet R.; Spek, C. Arnold; van Zonneveld, Anton Jan; Reitsma, Pieter H.; Hamming, Jaap F.; de Boer, Hetty C.; Versteeg, Henri H.; Quax, Paul H. A.

    2013-01-01

    Aims In collateral development (i.e. arteriogenesis), mononuclear cells are important and exist as a heterogeneous population consisting of pro-inflammatory and anti-inflammatory/repair-associated cells. Protease-activated receptor (PAR)1 and PAR2 are G-protein-coupled receptors that are both expressed by mononuclear cells and are involved in pro-inflammatory reactions, while PAR2 also plays a role in repair-associated responses. Here, we investigated the physiological role of PAR1 and PAR2 in arteriogenesis in a murine hind limb ischemia model. Methods and Results PAR1-deficient (PAR1-/-), PAR2-deficient (PAR2-/-) and wild-type (WT) mice underwent femoral artery ligation. Laser Doppler measurements revealed reduced post-ischemic blood flow recovery in PAR2-/- hind limbs when compared to WT, while PAR1-/- mice were not affected. Upon ischemia, reduced numbers of smooth muscle actin (SMA)-positive collaterals and CD31-positive capillaries were found in PAR2-/- mice when compared to WT mice, whereas these parameters in PAR1-/- mice did not differ from WT mice. The pool of circulating repair-associated (Ly6C-low) monocytes and the number of repair-associated (CD206-positive) macrophages surrounding collaterals in the hind limbs were increased in WT and PAR1-/- mice, but unaffected in PAR2-/- mice. The number of repair-associated macrophages in PAR2-/- hind limbs correlated with CD11b- and CD115-expression on the circulating monocytes in these animals, suggesting that monocyte extravasation and M-CSF-dependent differentiation into repair-associated cells are hampered. Conclusion PAR2, but not PAR1, is involved in arteriogenesis and promotes the repair-associated response in ischemic tissues. Therefore, PAR2 potentially forms a new pro-arteriogenic target in coronary artery disease (CAD) patients. PMID:23637930

  17. Failure analysis of brass tubes

    SciTech Connect

    Lawrence, S.J.; Bodnar, R.L.

    1997-02-01

    The 1996 Jacquet Lucas Award for Excellence in Metallography was won by Samuel J. Lawrence and Richard L. Bodnar for their analysis of cracks in Admiralty brass cooling tubes, which are part of a heat exchanger in a turbogenerator that provides electricity to a manufacturing plant. A mixture of non-recirculating city and spring pit water flows through bundles of tubes to cool the oil in which they are immersed. However, a problem developed when several of the brass tubes cracked transversely, allowing cooling water to mix with the oil. This award-winning entry in the ASM/IMS competition shows how the metallographers analyzed the cracks, and what the results were.

  18. Tubing and cable cutting tool

    NASA Technical Reports Server (NTRS)

    Mcsmith, D. D.; Richardson, J. I. (Inventor)

    1984-01-01

    A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

  19. Core-tube data logger

    SciTech Connect

    Henfling, J.A.; Normann, R.A.; Knudsen, S.; Drumheller, D.

    1997-01-01

    Wireline core drilling, increasingly used for geothermal exploration, employs a core-tube to capture a rock core sample during drilling. Three types of core-tube data loggers (CTDL) have been built and tested to date by Sandia national Laboratories. They are: (1) temperature-only logger, (2) temperature/inclinometer logger and (3) heat-shielded temperature/inclinometer logger. All were tested during core drilling operations using standard wireline diamond core drilling equipment. While these tools are designed for core-tube deployment, the tool lends itself to be adapted to other drilling modes and equipment. Topics covered in this paper include: (1) description on how the CTDLs are implemented, (2) the components of the system, (3) the type of data one can expect from this type of tool, (4) lessons learned, (5) comparison to its counterpart and (6) future work.

  20. End Calorimeter Warm Tube Heater

    SciTech Connect

    Primdahl, K.; /Fermilab

    1991-08-06

    The Tevatron accelerator beam tube must pass through the End Calorimeter cryostats of the D-Zero Collider Detector. Furthermore, the End Calorimeter cryostats must be allowed to roll back forty inches without interruption of the vacuum system; hence, the Tev tube must slide through the End Calorimeter cryostat as it is rolled back. The Tev pass through the End Calorimeter can actually be thought of as a cluster of concentric tubes: Tev tube, warm (vacuum vessel) tube, IS layers of superinsulation, cold tube (argon vessel), and Inner Hadronic center support tube. M. Foley generated an ANSYS model to study the heat load. to the cryostat. during collider physics studies; that is, without operation of the heater. A sketch of the model is included in the appendix. The vacuum space and superinsulation was modeled as a thermal solid, with conductivity derived from tests performed at Fermilab. An additional estimate was done. by this author, using data supplied by NR-2. a superinsulation manufacturer. The ANSYS result and hand calculation are in close agreement. The ANSYS model was modified. by this author. to incorporate the effect of the heater. Whereas the earlier model studied steady state operation only. the revised model considers the heater-off steady state mode as the initial condition. then performs a transient analysis with a final load step for time tending towards infinity. Results show the thermal gradient as a function of time and applied voltage. It should be noted that M. Foley's model was generated for one half the warm tube. implying the tube to be symmetric. In reality. the downstream connection (relative to the collision point) attachment to the vacuum shell is via several convolutions of a 0.020-inch wall bellows; hence. a nearly adiabatic boundary condition. Accordingly. the results reported in the table reflect extrapolation of the curves to the downstream end of the tube. Using results from the ANSYS analysis, that is, tube temperature and

  1. [The Use of a Tracheal Tube for Guiding Nasogastric Tube Insertion].

    PubMed

    Saima, Shunsuke; Asai, Takashi; Okuda, Yasuhisa

    2016-04-01

    An obese patient was scheduled for shoulder joint surgery under general anesthesia. After induction of anesthesia and tracheal intubation, insertion of a gastric tube was difficult. A new tracheal tube was prepared, the connecter was removed, and the tube was cut longitudinally. The tube was inserted orally into the esophagus. A gastric tube was passed through the nose, and its tip was taken out of the mouth. The tip of the gastric tube was passed through the tracheal tube, and its correct position in the stomach was confirmed by auscultation of the epigastrium. The tracheal tube was carefully taken out from the esophagus leaving the gastric tube in the stomach. The cut tracheal tube was peeled off from the gastric tube. Correct positioning of the gastric tube was re-confirmed.

  2. Transient junction anisotropies orient annular cell polarization in the Drosophila airway tubes.

    PubMed

    Hosono, Chie; Matsuda, Ryo; Adryan, Boris; Samakovlis, Christos

    2015-12-01

    In contrast to planes, three-dimensional (3D) structures such as tubes are physically anisotropic. Tubular organs exhibit a striking orientation of landmarks according to the physical anisotropy of the 3D shape, in addition to planar cell polarization. However, the influence of 3D tissue topography on the constituting cells remains underexplored. Here, we identify a regulatory network polarizing cellular biochemistry according to the physical anisotropy of the 3D tube geometry (tube cell polarization) by a genome-wide, tissue-specific RNAi screen. During Drosophila airway remodelling, each apical cellular junction is equipotent to establish perpendicular actomyosin cables, irrespective of the longitudinal or transverse tube axis. A dynamic transverse enrichment of atypical protein kinase C (aPKC) shifts the balance and transiently targets activated small GTPase RhoA, myosin phosphorylation and Rab11 vesicle trafficking to longitudinal junctions. We propose that the PAR complex translates tube physical anisotropy into longitudinal junctional anisotropy, where cell-cell communication aligns the contractile cytoskeleton of neighbouring cells.

  3. Working session 3: Tubing integrity

    SciTech Connect

    Cueto-Felgueroso, C.; Strosnider, J.

    1997-02-01

    Twenty-three individuals representing nine countries (Belgium, Canada, the Czech Republic, France, Japan, the Slovak Republic, Spain, the UK, and the US) participated in the session on tube integrity. These individuals represented utilities, vendors, consultants and regulatory authorities. The major subjects discussed by the group included overall objectives of managing steam generator tube degradation, necessary elements of a steam generator degradation management program, the concept of degradation specific management, structural integrity evaluations, leakage evaluations, and specific degradation mechanisms. The group`s discussions on these subjects, including conclusions and recommendations, are summarized in this article.

  4. The pollen tube paradigm revisited.

    PubMed

    Kroeger, Jens; Geitmann, Anja

    2012-12-01

    The polar growth process characterizing pollen tube elongation has attracted numerous modeling attempts over the past years. While initial models focused on recreating the correct cellular geometry, recent models are increasingly based on experimentally assessed cellular parameters such as the dynamics of signaling processes and the mechanical properties of the cell wall. Recent modeling attempts have therefore substantially gained in biological relevance and predictive power. Different modeling methods are explained and the power and limitations of individual models are compared. Focus is on several recent models that use closed feedback loops in order to generate limit cycles representing the oscillatory behavior observed in growing tubes. PMID:23000432

  5. Packing tube assembly for pumping wells

    SciTech Connect

    Towner, G.F.; Carter, C.A.

    1987-09-22

    A packing tube assembly for replacing a conventional stuffing box is described. The packing tube assembly comprising: a packing tube; a rod adaptor adapted to be coupled between the polished rod and the sucker rod string and adapted to extend throughout the packing tube when positioned therein; compressible packing means on the rod adaptor adapted to provide a seal between the rod adaptor and the packing tube when the rod adaptor is in position within the packing tube; stabilizing means on the rod adaptor adapted to engage the packing tube to stabilize the rod adaptor within the packing tube during operation; and a mounting bushing connected to the top of the packing tube and adapted to be threaded into the pumping tee to secure the packing tube position within the production tubing string. A method of converting a conventional stuffing box-equipped pumping well to a packing tube-equipped well is described. It consists of: disconnecting the polished rod of the pumping well from the sucker rod string while suspending the sucker rod string within the well by the use of slips; unthreading the conventional stuffing box from the pumping tee of the well and removing the stuffing box; attaching the polished rod to the upper end of a rod adaptor of a packing tube assembly, inserting the rod adaptor with the polished rod attached into the packing tube of the packing tube assembly; aligning the packing tube assembly with the sucker rod string; connecting the lower end of the rod adaptor to the sucker rod string; removing the slips and lowering the packer tube assembly through the pumping tee; and connecting the upper end of the packing tube to the pumping tee.

  6. Conjunctival inclusion cyst following repair of tube erosion in a child with aphakic glaucoma, leading to endophthalmitis

    PubMed Central

    Roy, Avik Kumar; Senthil, Sirisha

    2015-01-01

    Introduction: Glaucoma in aphakia is a major long term complication following congenital cataract surgery. Implantation of glaucoma drainage device provides an effective approach to manage refractory paediatric glaucoma. However implant surgery in young individuals is not free of complications. The prompt detection and management of tube erosion is of utmost importance to prevent devastating sequel of endophthalmitis. Implantation cyst following repair of tube erosion has not been reported so far. This case illustrates the rare occurrence of inclusion cyst following repair of tube erosion, the possible causes and its consequences. Case description: A 2-year-old child with aphakia developed intractable glaucoma. Following a failed glaucoma filtering surgery he underwent sequential Ahmed Glaucoma Valve implantation in both the eyes. Six weeks following right eye surgery, the child presented with conjunctival erosion overlying the tube, which was treated with scleral patch graft and conjunctival advancement. One month after the repair of tube erosion, the child presented with implantation cyst under the scleral patch graft, which was treated by drainage with a 29G needle. The child presented with endophthalmitis of his right eye following an episode of bilateral conjunctivitis. This was managed by an emergency pars plana vitrectomy, intraocular antibiotics and tube excision. At the last follow up visit, the IOP was 20 mmHg with 2 topical antiglaucoma medications in the right eye following a trans scleral photocoagulation. Discussion: Lifelong careful follow-up of paediatric eyes with implant surgery is mandatory to look for complication such as tube erosion. It is important to place additional sutures to secure the patch graft during implantation of glaucoma drainage devices in children to prevent graft displacement and consequent tube erosion. During repair of tube erosion, it is crucial to remove all the conjunctival epithelium around the tube, thus not to

  7. Conjunctival inclusion cyst following repair of tube erosion in a child with aphakic glaucoma, leading to endophthalmitis

    PubMed Central

    Roy, Avik Kumar; Senthil, Sirisha

    2015-01-01

    Introduction: Glaucoma in aphakia is a major long term complication following congenital cataract surgery. Implantation of glaucoma drainage device provides an effective approach to manage refractory paediatric glaucoma. However implant surgery in young individuals is not free of complications. The prompt detection and management of tube erosion is of utmost importance to prevent devastating sequel of endophthalmitis. Implantation cyst following repair of tube erosion has not been reported so far. This case illustrates the rare occurrence of inclusion cyst following repair of tube erosion, the possible causes and its consequences. Case description: A 2-year-old child with aphakia developed intractable glaucoma. Following a failed glaucoma filtering surgery he underwent sequential Ahmed Glaucoma Valve implantation in both the eyes. Six weeks following right eye surgery, the child presented with conjunctival erosion overlying the tube, which was treated with scleral patch graft and conjunctival advancement. One month after the repair of tube erosion, the child presented with implantation cyst under the scleral patch graft, which was treated by drainage with a 29G needle. The child presented with endophthalmitis of his right eye following an episode of bilateral conjunctivitis. This was managed by an emergency pars plana vitrectomy, intraocular antibiotics and tube excision. At the last follow up visit, the IOP was 20 mmHg with 2 topical antiglaucoma medications in the right eye following a trans scleral photocoagulation. Discussion: Lifelong careful follow-up of paediatric eyes with implant surgery is mandatory to look for complication such as tube erosion. It is important to place additional sutures to secure the patch graft during implantation of glaucoma drainage devices in children to prevent graft displacement and consequent tube erosion. During repair of tube erosion, it is crucial to remove all the conjunctival epithelium around the tube, thus not to

  8. Croissance epitaxiale de GaAs sur substrats de Ge par epitaxie par faisceaux chimiques

    NASA Astrophysics Data System (ADS)

    Belanger, Simon

    La situation energetique et les enjeux environnementaux auxquels la societe est confrontee entrainent un interet grandissant pour la production d'electricite a partir de l'energie solaire. Parmi les technologies actuellement disponibles, la filiere du photovoltaique a concentrateur solaire (CPV pour concentrator photovoltaics) possede un rendement superieur et mi potentiel interessant a condition que ses couts de production soient competitifs. La methode d'epitaxie par faisceaux chimiques (CBE pour chemical beam epitaxy) possede plusieurs caracteristiques qui la rendent interessante pour la production a grande echelle de cellules photovoltaiques a jonctions multiples a base de semi-conducteurs III-V. Ce type de cellule possede la meilleure efficacite atteinte a ce jour et est utilise sur les satellites et les systemes photovoltaiques a concentrateur solaire (CPV) les plus efficaces. Une des principales forces de la technique CBE se trouve dans son potentiel d'efficacite d'utilisation des materiaux source qui est superieur a celui de la technique d'epitaxie qui est couramment utilisee pour la production a grande echelle de ces cellules. Ce memoire de maitrise presente les travaux effectues dans le but d'evaluer le potentiel de la technique CBE pour realiser la croissance de couches de GaAs sur des substrats de Ge. Cette croissance constitue la premiere etape de fabrication de nombreux modeles de cellules solaires a haute performance decrites plus haut. La realisation de ce projet a necessite le developpement d'un procede de preparation de surface pour les substrats de germanium, la realisation de nombreuses sceances de croissance epitaxiale et la caracterisation des materiaux obtenus par microscopie optique, microscopie a force atomique (AFM), diffraction des rayons-X a haute resolution (HRXRD), microscopie electronique a transmission (TEM), photoluminescence a basse temperature (LTPL) et spectrometrie de masse des ions secondaires (SIMS). Les experiences ont permis

  9. Par-4 secretion: stoichiometry of 3-arylquinoline binding to vimentin.

    PubMed

    Sviripa, Vitaliy M; Burikhanov, Ravshan; Obiero, Josiah M; Yuan, Yaxia; Nickell, Justin R; Dwoskin, Linda P; Zhan, Chang-Guo; Liu, Chunming; Tsodikov, Oleg V; Rangnekar, Vivek M; Watt, David S

    2016-01-01

    Advanced prostate tumors usually metastasize to the lung, bone, and other vital tissues and are resistant to conventional therapy. Prostate apoptosis response-4 protein (Par-4) is a tumor suppressor that causes apoptosis in therapy-resistant prostate cancer cells by binding specifically to a receptor, Glucose-regulated protein-78 (GRP78), found only on the surface of cancer cells. 3-Arylquinolines or "arylquins" induce normal cells to release Par-4 from the intermediate filament protein, vimentin and promote Par-4 secretion that targets cancer cells in a paracrine manner. A structure-activity study identified arylquins that promote Par-4 secretion, and an evaluation of arylquin binding to the hERG potassium ion channel using a [(3)H]-dofetilide binding assay permitted the identification of structural features that separated this undesired activity from the desired Par-4 secretory activity. A binding study that relied on the natural fluorescence of arylquins and that used the purified rod domain of vimentin (residues 99-411) suggested that the mechanism behind Par-4 release involved arylquin binding to multiple sites in the rod domain.

  10. Fin-tube solar collectors

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Report presents test procedures and results of thermal-performance evaluation of seven commercial fin tube (liquid) solar collector-absorber plates. Tests were conducted indoors at Marshall Space Flight Center Solar simulator. Results are graphically shown along with supporting test data and summary, indicating efficiency as function of collector inlet temperature.

  11. Working session 1: Tubing degradation

    SciTech Connect

    Kharshafdjian, G.; Turluer, G.

    1997-02-01

    A general introductory overview of the purpose of the group and the general subject area of SG tubing degradation was given by the facilitator. The purpose of the session was described as to {open_quotes}develop conclusions and proposals on regulatory and technical needs required to deal with the issues of SG tubing degradation.{close_quotes} Types, locations and characteristics of tubing degradation in steam generators were briefly reviewed. The well-known synergistic effects of materials, environment, and stress and strain/strain rate, subsequently referred to by the acronym {open_quotes}MESS{close_quotes} by some of the group members, were noted. The element of time (i.e., evolution of these variables with time) was emphasized. It was also suggested that the group might want to consider the related topics of inspection capabilities, operational variables, degradation remedies, and validity of test data, and some background information in these areas was provided. The presentation given by Peter Millet during the Plenary Session was reviewed; Specifically, the chemical aspects and the degradation from the secondary side of the steam generator were noted. The main issues discussed during the October 1995 EPRI meeting on secondary side corrosion were reported, and a listing of the potential SG tube degradations was provided and discussed.

  12. Kundt's Tube Experiment Using Smartphones

    ERIC Educational Resources Information Center

    Parolin, Sara Orsola; Pezzi, Giovanni

    2015-01-01

    This article deals with a modern version of Kundt's tube experiment. Using economic instruments and a couple of smartphones, it is possible to "see" nodes and antinodes of standing acoustic waves in a column of vibrating air and to measure the speed of sound.

  13. A malfunctioning nasogastric feeding tube.

    PubMed

    Cereda, Emanuele; Costa, Antonio; Caccialanza, Riccardo; Pedrolli, Carlo

    2013-01-01

    A critical point of nasogastric feeding tube placement, potentially resulting in an unsafe and/or non-effective operation of the device, is the monitoring of its proper placement into the stomach. A properly obtained and interpreted radiograph is currently recommended to confirm placement. We reported the case of a 68-year-old demented woman referred for complicated dysphagia. A nasogastric tube was blindly inserted and its placement was confirmed by the radiologist. Enteral nutrition was initiated but the patient began to vomit immediately. After reviewing the radiograph it was understood that a gastric loop in the tube and its tip pointing upwards did not allow a safe infusion of the feeding formula. It is not enough having the radiologist reporting that a nasogastric feeding tube is placed in the stomach; the inclusion in the report of specific warnings on any potential cause of malfunctioning of the device should be considered. The presence of a gastric loop should be taken into account as a cause of potential malfunctioning.

  14. Remote-Action Tube Crimper

    NASA Technical Reports Server (NTRS)

    Robbins, R. L.; Harrison, S. T.

    1983-01-01

    Long-handled tube crimper stops leaks or reduces fluid flow in hard to reach and hazardous areas. Tool includes steel plunger, contained within pipe, and long cam-action handles that open and close crimping jaw. Movable jaw is wedge shaped and stationary jaw cylindrical.

  15. Impulse generation by detonation tubes

    NASA Astrophysics Data System (ADS)

    Cooper, Marcia Ann

    Impulse generation with gaseous detonation requires conversion of chemical energy into mechanical energy. This conversion process is well understood in rocket engines where the high pressure combustion products expand through a nozzle generating high velocity exhaust gases. The propulsion community is now focusing on advanced concepts that utilize non-traditional forms of combustion like detonation. Such a device is called a pulse detonation engine in which laboratory tests have proven that thrust can be achieved through continuous cyclic operation. Because of poor performance of straight detonation tubes compared to conventional propulsion systems and the success of using nozzles on rocket engines, the effect of nozzles on detonation tubes is being investigated. Although previous studies of detonation tube nozzles have suggested substantial benefits, up to now there has been no systematic investigations over a range of operating conditions and nozzle configurations. As a result, no models predicting the impulse when nozzles are used exist. This lack of data has severely limited the development and evaluation of models and simulations of nozzles on pulse detonation engines. The first experimental investigation measuring impulse by gaseous detonation in plain tubes and tubes with nozzles operating in varying environment pressures is presented. Converging, diverging, and converging-diverging nozzles were tested to determine the effect of divergence angle, nozzle length, and volumetric fill fraction on impulse. The largest increases in specific impulse, 72% at an environment pressure of 100 kPa and 43% at an environment pressure of 1.4 kPa, were measured with the largest diverging nozzle tested that had a 12° half angle and was 0.6 m long. Two regimes of nozzle operation that depend on the environment pressure are responsible for these increases and were first observed from these data. To augment this experimental investigation, all data in the literature regarding

  16. Apparatus for connecting aligned abutted tubes

    DOEpatents

    Williams, R.E.

    1984-11-29

    An apparatus for connecting abutted tubes and for maintaining their rotary alignment during connection. The apparatus comprises first and second tubes, a rotation prevention element, a collar and a retainer. Each tube has inside and outside walls, and first and second ends, each end having an inside and outside edge. The first tube has portions defining a first plurality of cavities located at the outside edge of its first end. An external threaded portion is on the outside wall of the first tube and next to the first plurality of cavities. The second tube has portions defining a second plurality of cavities located at the outside edge of its first end. The first plurality has a different number than the second plurality. The first ends of the first and second tubes have substantially the same outside diameter and are abutted during connection so that an orifice is formed whenever first and second tube cavities substantially overlap. A rotation prevension element is placed in the orifice to prevent rotation of the first and second tubes. A collar with an internal threaded portion is slidably disposed about the second tube. The internal threaded portion engages the external threaded portion of the first tube to connect the tubes. A lip connected to the collar prevents separation of the collar from the second tube.

  17. Small bore ceramic laser tube inspection light table

    DOEpatents

    Updike, Earl O.

    1990-01-01

    Apparatus for inspecting small bore ceramic laser tubes, which includes a support base with one or more support rollers. A fluorescent light tube is inserted within the laser tube and the laser tube is supported by the support rollers so that a gap is maintained between the laser tube and the fluorescent tube to enable rotation of the laser tube. In operation, the ceramic tube is illuminated from the inside by the fluorescent tube to facilitate visual inspection. Centering the tube around the axial light of the fluorescent tube provides information about straightness and wall thickness of the laser tube itself.

  18. Reduce - and Report - Enteral Feeding Tube Misconnections

    MedlinePlus

    ... patient requiring mechanical ventilation also had a nasogastric (NG) tube in place. After being transported to another ... high-flow oxygen was accidentally connected to the NG tube. The patient subsequently underwent emergency surgery to ...

  19. When to change a tracheostomy tube.

    PubMed

    White, Alexander C; Kher, Sucharita; O'Connor, Heidi H

    2010-08-01

    Knowing when to change a tracheostomy tube is important for optimal management of all patients with tracheostomy tubes. The first tracheostomy tube change, performed 1-2 weeks after placement, carries some risk and should be performed by a skilled operator in a safe environment. The risk associated with changing the tracheostomy tube then usually diminishes over time as the tracheo-cutaneous tract matures. A malpositioned tube can be a source of patient distress and patient-ventilator asynchrony, and is important to recognize and correct. Airway endoscopy can be helpful to ensure optimal positioning of a replacement tracheostomy tube. Some of the specialized tracheostomy tubes available on the market are discussed. There are few data available to guide the timing of routine tracheostomy tube changes. Some guidelines are suggested. PMID:20667154

  20. Chemical recombination in an expansion tube

    NASA Technical Reports Server (NTRS)

    Bakos, Robert J.; Morgan, Richard G.

    1994-01-01

    The note describes the theoretical basis of chemical recombination in an expansion tube which simulates energy, Reynolds number, and stream chemistry at near-orbital velocities. Expansion tubes can satisfy ground-based hypersonic propulsion and aerothermal testing requirements.

  1. Conceptual optimization using genetic algorithms for tube in tube structures

    SciTech Connect

    Pârv, Bianca Roxana; Hulea, Radu; Mojolic, Cristian

    2015-03-10

    The purpose of this article is to optimize the tube in tube structural systems for tall buildings under the horizontal wind loads. It is well-known that the horizontal wind loads is the main criteria when choosing the structural system, the types and the dimensions of structural elements in the majority of tall buildings. Thus, the structural response of tall buildings under the horizontal wind loads will be analyzed for 40 story buildings and a total height of 120 meters; the horizontal dimensions will be 30m × 30m for the first two optimization problems and 15m × 15m for the third. The optimization problems will have the following as objective function the cross section area, as restrictions the displacement of the building< the admissible displacement (H/500), and as variables the cross section dimensions of the structural elements.

  2. Models for Automated Tube Performance Calculations

    SciTech Connect

    C. Brunkhorst

    2002-12-12

    High power radio-frequency systems, as typically used in fusion research devices, utilize vacuum tubes. Evaluation of vacuum tube performance involves data taken from tube operating curves. The acquisition of data from such graphical sources is a tedious process. A simple modeling method is presented that will provide values of tube currents for a given set of element voltages. These models may be used as subroutines in iterative solutions of amplifier operating conditions for a specific loading impedance.

  3. [A tube retractor for cardiac surgery].

    PubMed

    Ohkado, A; Shiikawa, A; Ishitoya, H; Murata, A

    2001-03-01

    A retractor exclusively used to retract the tubes in cardiac surgery which needs cardiopulmonary bypass was developed. The half-cylinder-shaped end, the lightly curved handle and the flat and triangular grip enable easy and effective grasp of the tubes. This new instrument facilitates operative procedures by effectively retracting the tubes which persistently obstruct the operative field, in such a case of placement of a retrograde cardioplegia tube via the right atrium.

  4. Par Pond vegetation status Summer 1995 -- June survey descriptive summary

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1995-06-01

    The water level of Par Pond was lowered approximately 20 feet in mid-1991 in order to protect downstream residents from possible dam failure suggested by subsidence on the downstream slope of the dam and to repair the dam. This lowering exposed both emergent and nonemergent macrophyte beds to drying conditions resulting in extensive losses. A survey of the shoreline aquatic plant communities in June 1995, three months after the refilling of Par Pond to approximately 200 feet above mean sea level, indicated that much of the original plant communities and the intermediate shoreline communities present on the exposed sediments have been lost. The extensive old-field and emergent marsh communities that were present on the exposed shoreline during the drawdown have been flooded and much of the pre-drawdown Par Pond aquatic plant communities have not had sufficient time for re-establishment. The shoreline does, however, have extensive beds of maidencane which extend from the shoreline margin to areas as deep as 2 and perhaps 3 meters. Scattered individual plants of lotus and watershield are common and may indicate likely directions of future wetland development in Par Pond. In addition, within isolated coves, which apparently received ground water seepage and/or stream surface flows during the period of the Par Pond draw down, extensive beds of waterlilies and spike rush are common. Invasion of willow and red maple occurred along the lake shoreline as well. Although not absent from this survey, evidence of the extensive redevelopment of the large cattail and eel grass beds was not observed in this first survey of Par Pond. Future surveys during the growing seasons of 1995, 1996, and 1997 along with the evaluation of satellite date to map the areal extent of the macrophyte beds of Par Pond are planned.

  5. Pars Planitis: Epidemiology, Clinical Characteristics, Management and Visual Prognosis.

    PubMed

    Ozdal, Pinar Cakar; Berker, Nilufer; Tugal-Tutkun, Ilknur

    2015-01-01

    Pars planitis is an idiopathic chronic intermediate uveitis which predominantly affects children and adolescents, and accounts for 5-26.7% of pediatric uveitis. Although an autoimmune process with a genetic predisposition has been suggested, its etiology still remains unknown. The most common presenting symptoms are floaters and blurred vision. Diffuse vitreous cells, haze, snowballs and snowbanks are typical findings of pars planitis. Peripheral retinal vasculitis, optic disc edema and anterior segment inflammation are other well-known findings. Although pars planitis is known to be a benign form of uveitis in most cases, it may become a potentially blinding disease due to complications including cataract, cystoid macular edema, vitreous opacities and optic disc edema. Cystoid macular edema is the most common cause of visual morbidity. Band keratopathy, epiretinal membrane formation, vitreous condensation, neovascularizations, vitreous hemorrhage, retinal detachment, cyclitic membranes, glaucoma and amblyopia may develop as a consequence of the chronic course of the disease. Exclusion of infectious and non-infectious causes which may present with intermediate uveitis is of utmost importance before starting treatment. Treatment of pars planitis has been a controversial issue. There is no consensus specifically for treatment of cases with minimal inflammation and relatively good visual acuity. However, current experience shows that pars planitis may cause severe inflammation and needs an aggressive treatment. A stepladder approach including corticosteroids, immunosupressive agents, anti-tumor necrosis factor-alpha and pars plana vitrectomy and/or laser photocoagulation is the most commonly used method for treatment of pars planitis. Adequate control of inflammation and prompt detection of associated complications are crucial in order to improve the overall prognosis of the disease. PMID:27051493

  6. Pars Planitis: Epidemiology, Clinical Characteristics, Management and Visual Prognosis

    PubMed Central

    Ozdal, Pinar Cakar; Berker, Nilufer; Tugal-Tutkun, Ilknur

    2015-01-01

    Pars planitis is an idiopathic chronic intermediate uveitis which predominantly affects children and adolescents, and accounts for 5-26.7% of pediatric uveitis. Although an autoimmune process with a genetic predisposition has been suggested, its etiology still remains unknown. The most common presenting symptoms are floaters and blurred vision. Diffuse vitreous cells, haze, snowballs and snowbanks are typical findings of pars planitis. Peripheral retinal vasculitis, optic disc edema and anterior segment inflammation are other well-known findings. Although pars planitis is known to be a benign form of uveitis in most cases, it may become a potentially blinding disease due to complications including cataract, cystoid macular edema, vitreous opacities and optic disc edema. Cystoid macular edema is the most common cause of visual morbidity. Band keratopathy, epiretinal membrane formation, vitreous condensation, neovascularizations, vitreous hemorrhage, retinal detachment, cyclitic membranes, glaucoma and amblyopia may develop as a consequence of the chronic course of the disease. Exclusion of infectious and non-infectious causes which may present with intermediate uveitis is of utmost importance before starting treatment. Treatment of pars planitis has been a controversial issue. There is no consensus specifically for treatment of cases with minimal inflammation and relatively good visual acuity. However, current experience shows that pars planitis may cause severe inflammation and needs an aggressive treatment. A stepladder approach including corticosteroids, immunosupressive agents, anti-tumor necrosis factor-alpha and pars plana vitrectomy and/or laser photocoagulation is the most commonly used method for treatment of pars planitis. Adequate control of inflammation and prompt detection of associated complications are crucial in order to improve the overall prognosis of the disease. PMID:27051493

  7. Comparison of the effects of PAR1 antagonists, PAR4 antagonists, and their combinations on thrombin-induced human platelet activation.

    PubMed

    Wu, Chin-Chung; Teng, Che-Ming

    2006-09-28

    Thrombin activates human platelets through proteolytic activation of two protease-activated receptors (PARs), PAR1 and PAR4. In the present study, we show that, RWJ-56110, a potent synthetic PAR1 antagonist, inhibited platelet aggregation caused by a low concentration (0.05 U/ml) of thrombin, but lost its effectiveness when higher concentrations of thrombin were used as stimulators. YD-3, a non-peptide PAR4 antagonist, alone had little or no effect on thrombin-induced platelet aggregation, significantly enhanced the anti-aggregatory activity of PAR1 antagonist. In addition, we demonstrate for the first time that P-selectin expression in thrombin-stimulated platelets can be synergistically prevented by combined treatment of PAR1 antagonist and PAR4 antagonist. These results indicate that thrombin-induced platelet activation cannot be effectively inhibited by just blocking either single thrombin receptor pathway, and suggest a rationale for potential combination therapy in arterial thrombosis. PMID:16890935

  8. The Fuge Tube Diode Array Spectrophotometer

    ERIC Educational Resources Information Center

    Arneson, B. T.; Long, S. R.; Stewart, K. K.; Lagowski, J. J.

    2008-01-01

    We present the details for adapting a diode array UV-vis spectrophotometer to incorporate the use of polypropylene microcentrifuge tubes--fuge tubes--as cuvettes. Optical data are presented validating that the polyethylene fuge tubes are equivalent to the standard square cross section polystyrene or glass cuvettes generally used in…

  9. Kundt's Tube: An Acoustic Gas Analyzer

    ERIC Educational Resources Information Center

    Aristov, Natasha; Habekost, Gehsa; Habekost, Achim

    2011-01-01

    A Kundt tube is normally used to measure the speed of sound in gases. Therefore, from known speeds of sound, a Kundt tube can be used to identify gases and their fractions in mixtures. In these experiments, the speed of sound is determined by measuring the frequency of a standing sound wave at a fixed tube length, temperature, and pressure. This…

  10. Spring/dimple instrument tube restraint

    DOEpatents

    DeMario, Edmund E.; Lawson, Charles N.

    1993-01-01

    A nuclear fuel assembly for a pressurized water nuclear reactor has a spring and dimple structure formed in a non-radioactive insert tube placed in the top of a sensor receiving instrumentation tube thimble disposed in the fuel assembly and attached at a top nozzle, a bottom nozzle, and intermediate grids. The instrumentation tube thimble is open at the top, where the sensor or its connection extends through the cooling water for coupling to a sensor signal processor. The spring and dimple insert tube is mounted within the instrumentation tube thimble and extends downwardly adjacent the top. The springs and dimples restrain the sensor and its connections against lateral displacement causing impact with the instrumentation tube thimble due to the strong axial flow of cooling water. The instrumentation tube has a stainless steel outer sleeve and a zirconium alloy inner sleeve below the insert tube adjacent the top. The insert tube is relatively non-radioactivated inconel alloy. The opposed springs and dimples are formed on diametrically opposite inner walls of the insert tube, the springs being formed as spaced axial cuts in the insert tube, with a web of the insert tube between the cuts bowed radially inwardly for forming the spring, and the dimples being formed as radially inward protrusions opposed to the springs.

  11. Spring/dimple instrument tube restraint

    DOEpatents

    DeMario, E.E.; Lawson, C.N.

    1993-11-23

    A nuclear fuel assembly for a pressurized water nuclear reactor has a spring and dimple structure formed in a non-radioactive insert tube placed in the top of a sensor receiving instrumentation tube thimble disposed in the fuel assembly and attached at a top nozzle, a bottom nozzle, and intermediate grids. The instrumentation tube thimble is open at the top, where the sensor or its connection extends through the cooling water for coupling to a sensor signal processor. The spring and dimple insert tube is mounted within the instrumentation tube thimble and extends downwardly adjacent the top. The springs and dimples restrain the sensor and its connections against lateral displacement causing impact with the instrumentation tube thimble due to the strong axial flow of cooling water. The instrumentation tube has a stainless steel outer sleeve and a zirconium alloy inner sleeve below the insert tube adjacent the top. The insert tube is relatively non-radioactivated inconel alloy. The opposed springs and dimples are formed on diametrically opposite inner walls of the insert tube, the springs being formed as spaced axial cuts in the insert tube, with a web of the insert tube between the cuts bowed radially inwardly for forming the spring, and the dimples being formed as radially inward protrusions opposed to the springs. 7 figures.

  12. Heat exchanger with a removable tube section

    DOEpatents

    Wolowodiuk, W.; Anelli, J.

    1975-07-29

    A heat exchanger is described in which the tube sheet is secured against primary liquid pressure, but which allows for easy removal of the tube section. The tube section is supported by a flange which is secured by a number of shear blocks, each of which extends into a slot which is immovable with respect to the outer shell of the heat exchanger. (auth)

  13. Intraoperative monitoring of Jones tube function.

    PubMed

    Kartchner, M J; Mather, T R; Dryden, R M

    1989-01-01

    If intraoperative visualization is impossible when placing a secondary Jones tube, the presence of tube drainage may confirm correct intranasal positioning. A simple suction method is presented to evaluate the intranasal position of the Jones tube in the anesthetized or uncooperative patient.

  14. Manual tube-to-tubesheet welding torch

    DOEpatents

    Kiefer, Joseph H.; Smith, Danny J.

    1982-01-01

    A welding torch made of a high temperature plastic which fits over a tube intermediate the ends thereof for welding the juncture between the tube and the back side of a tube plate and has a ballooned end in which an electrode, filler wire guide, fiber optic bundle, and blanketing gas duct are disposed.

  15. 21 CFR 868.5730 - Tracheal tube.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Tracheal tube. 868.5730 Section 868.5730 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5730 Tracheal tube. (a) Identification. A tracheal tube is...

  16. 21 CFR 868.5730 - Tracheal tube.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tracheal tube. 868.5730 Section 868.5730 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5730 Tracheal tube. (a) Identification. A tracheal tube is...

  17. 21 CFR 874.3880 - Tympanostomy tube.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Tympanostomy tube. 874.3880 Section 874.3880 Food... DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3880 Tympanostomy tube. (a) Identification. A tympanostomy tube is a device that is intended to be implanted for ventilation or drainage of...

  18. 21 CFR 868.5730 - Tracheal tube.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Tracheal tube. 868.5730 Section 868.5730 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5730 Tracheal tube. (a) Identification. A tracheal tube is...

  19. 21 CFR 868.5730 - Tracheal tube.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Tracheal tube. 868.5730 Section 868.5730 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5730 Tracheal tube. (a) Identification. A tracheal tube is...

  20. 21 CFR 874.3880 - Tympanostomy tube.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Tympanostomy tube. 874.3880 Section 874.3880 Food... DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3880 Tympanostomy tube. (a) Identification. A tympanostomy tube is a device that is intended to be implanted for ventilation or drainage of...

  1. 21 CFR 874.3880 - Tympanostomy tube.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Tympanostomy tube. 874.3880 Section 874.3880 Food... DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3880 Tympanostomy tube. (a) Identification. A tympanostomy tube is a device that is intended to be implanted for ventilation or drainage of...

  2. 21 CFR 868.5730 - Tracheal tube.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Tracheal tube. 868.5730 Section 868.5730 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5730 Tracheal tube. (a) Identification. A tracheal tube is...

  3. A Three-Cent Reusable Craig Tube

    NASA Astrophysics Data System (ADS)

    Russo, Thomas J.

    1998-07-01

    A rugged three-cent reusable Craig tube is easily made from a cotton swab and disposable pipet tip. The tube costs three cents or less and can be reused. Craig tubes made of glass cost as much as $15 and are very fragile.

  4. Regulation of protease-activated receptor (PAR) 1 and PAR4 signaling in human platelets by compartmentalized cyclic nucleotide actions.

    PubMed

    Bilodeau, Matthew L; Hamm, Heidi E

    2007-08-01

    Thrombin potently regulates human platelets by the G protein-coupled receptors protease-activated receptor (PAR) 1 and PAR4. Platelet activation by thrombin and other agonists is broadly inhibited by prostacyclin and nitric oxide acting through adenylyl and guanylyl cyclases to elevate cAMP and cGMP levels, respectively. Using forskolin and YC-1 [3-(5'-hydroxymethyl-2'-furyl)-1-benzylindazole] to selectively activate the adenylyl and guanylyl cyclases, respectively, and the membrane-permeable analogs N(6),2'-O-dibutyryladenosine-3'-5'-cAMP (dibutyryl-cAMP) and 8-(4-parachlorophenylthoi)-cGMP (8-pCPT-cGMP), we sought to identify key antiplatelet steps for cyclic nucleotide actions in blocking platelet activation by PAR1 versus PAR4. Platelet aggregation by PAR1 or PAR4 was inhibited with similar EC(50) of 1.2 to 2.1 microM forskolin, 31 to 33 microM YC-1, 57 to 150 microM dibutyryl-cAMP, and 220 to 410 microM 8-pCPT-cGMP. There was a marked left shift in the inhibitory potencies of forskolin and YC-1 for alpha-granule release and glycoprotein IIbIIIa/integrin alphaIIbbeta3 activation (i.e., EC(50) of 1-60 and 40-1300 nM, respectively) that was not observed for dibutyryl-cAMP and 8-pCPT-cGMP (i.e., EC(50) of 200-600 and 40-140 microM, respectively). This inhibition was essentially instantaneous, and measurements of cyclic nucleotide levels and kinase activities support a model of compartmentation involving the cyclic nucleotide effectors and regulators and the key molecular targets for this platelet inhibition. The different sensitivities of PAR1 and PAR4 to inhibition of calcium mobilization and dense granule release identify key antiplatelet steps for cyclic nucleotide actions and are consistent with the signaling models for these receptors. Specifically, PAR4 inhibition depends on the regulation of both calcium mobilization and dense granule release, and PAR1 inhibition depends predominantly on the regulation of dense granule release. PMID:17525299

  5. Ionization tube simmer current circuit

    DOEpatents

    Steinkraus, R.F. Jr.

    1994-12-13

    A highly efficient flash lamp simmer current circuit utilizes a fifty percent duty cycle square wave pulse generator to pass a current over a current limiting inductor to a full wave rectifier. The DC output of the rectifier is then passed over a voltage smoothing capacitor through a reverse current blocking diode to a flash lamp tube to sustain ionization in the tube between discharges via a small simmer current. An alternate embodiment of the circuit combines the pulse generator and inductor in the form of an FET off line square wave generator with an impedance limited step up output transformer which is then applied to the full wave rectifier as before to yield a similar simmer current. 6 figures.

  6. ATLS: Catheter and tube placement

    NASA Technical Reports Server (NTRS)

    Gosbee, John; Krupa, Debra T.; Pepper, L.; Orsak, Debra

    1991-01-01

    The specific objectives of this experiment are: to evaluate the rack mounted equipment and medical supplies necessary for medical procedures; to evaluate the attachments, mounting points, and inner drawer assemblies for the medical supplies; and to evaluate the procedures for performing medical scenarios. The resources available in the HMF miniracks to accomplish medical scenarios and/or procedures include: medical equipment mounted in the racks; a patch panel with places to attach tubing and catheters; self contained drawers full of critical care medical supplies; and an ALS 'backpack' for deploying supplies. The attachment lines, tubing and associated medical supplies will be deployed and used with the equipment and a patient mannequin. Data collection is provided by direct observations by the inflight experimenters, and analysis of still and video photography.

  7. HIGH CURRENT COAXIAL PHOTOMULTIPLIER TUBE

    DOEpatents

    Glass, N.W.

    1960-01-19

    A medium-gain photomultiplier tube having high current output, fast rise- time, and matched output impedance was developed. The photomultiplier tube comprises an elongated cylindrical envelope, a cylindrical anode supported at the axis of the envelope, a plurality of elongated spaced opaque areas on the envelope, and a plurality of light admitting windows. A photo-cathode is supported adjacent to each of the windows, and a plurality of secondary emissive dynodes are arranged in two types of radial arrays which are alternately positioned to fill the annular space between the anode and the envelope. The dynodes are in an array being radially staggered with respect to the dynodes in the adjacent array, the dynodes each having a portion arranged at an angle with respect to the electron path, such that electrons emitted by each cathode undergo multiplication upon impingement on a dynode and redirected flight to the next adjacent dynode.

  8. Ionization tube simmer current circuit

    DOEpatents

    Steinkraus, Jr., Robert F.

    1994-01-01

    A highly efficient flash lamp simmer current circuit utilizes a fifty percent duty cycle square wave pulse generator to pass a current over a current limiting inductor to a full wave rectifier. The DC output of the rectifier is then passed over a voltage smoothing capacitor through a reverse current blocking diode to a flash lamp tube to sustain ionization in the tube between discharges via a small simmer current. An alternate embodiment of the circuit combines the pulse generator and inductor in the form of an FET off line square wave generator with an impedance limited step up output transformer which is then applied to the full wave rectifier as before to yield a similar simmer current.

  9. Stochastic Self-Assembly of ParB Proteins Builds the Bacterial DNA Segregation Apparatus.

    PubMed

    Sanchez, Aurore; Cattoni, Diego I; Walter, Jean-Charles; Rech, Jérôme; Parmeggiani, Andrea; Nollmann, Marcelo; Bouet, Jean-Yves

    2015-08-26

    Many canonical processes in molecular biology rely on the dynamic assembly of higher-order nucleoprotein complexes. In bacteria, the assembly mechanism of ParABS, the nucleoprotein super-complex that actively segregates the bacterial chromosome and many plasmids, remains elusive. We combined super-resolution microscopy, quantitative genome-wide surveys, biochemistry, and mathematical modeling to investigate the assembly of ParB at the centromere-like sequences parS. We found that nearly all ParB molecules are actively confined around parS by a network of synergistic protein-protein and protein-DNA interactions. Interrogation of the empirically determined, high-resolution ParB genomic distribution with modeling suggests that instead of binding only to specific sequences and subsequently spreading, ParB binds stochastically around parS over long distances. We propose a new model for the formation of the ParABS partition complex based on nucleation and caging: ParB forms a dynamic lattice with the DNA around parS. This assembly model and approach to characterizing large-scale, dynamic interactions between macromolecules may be generalizable to many unrelated machineries that self-assemble in superstructures. PMID:27135801

  10. Through tubing progressing cavity pump

    SciTech Connect

    Morgan, A.E.

    1986-06-03

    A method is described of installing a progressing cavity pump assembly within a well, the pump assembly being of the type having a stator, a helical rotor located in the stator and rotated by a string of sucker rods extending through tubing to the surface. The method consists of: securing a tubular seating member to a lower end of the tubing and lowering the tubing into the well; mounting a seating member on a lower end of the pump assembly; mounting a rotor nipple to the upper end of the stator and a drive rod to the upper end of the rotor, and providing the rotor nipple and drive rod with engaging means that allows a selected amount of vertical movement of the rotor with respect to the stator; connecting the upper end of the drive rod to the sucker rods; lowering the pump assembly into the tubing on the sucker rods until the seating member on the pump assembly contacts the tubular seating member; continuing to lower the sucker rods without rotation, moving the rotor downward with respect to the stator and forcing the seating members together with the weight of the sucker rods applied to the stator through the engaging means; then moving the sucker rods and the rotor a selected distance upward while the stator remains stationary to position the top of the rotor above the stator a selected distance; then connecting the sucker rods at the surface to a rotary power source and rotating the sucker rods to cause the pump to operate.

  11. Cold cathode vacuum discharge tube

    DOEpatents

    Boettcher, Gordon E.

    1998-01-01

    A cold cathode vacuum discharge tube, and method for making same, with an interior surface of the trigger probe coated with carbon deposited by carbon vapor deposition (CVD) or diamond-like carbon (DLC) deposition. Preferably a solid graphite insert is employed in the probe-cathode structure in place of an aluminum bushing employed in the prior art. The CVD or DLC probe face is laser scribed to allow resistance trimming to match available trigger voltage signals and to reduce electrical aging.

  12. Gated SIT Vidicon Streak Tube

    NASA Astrophysics Data System (ADS)

    Dunbar, D. L.; Yates, G. J.; Black, J. P.

    1986-01-01

    A recently developed prototype streak tube designed to produce high gain and resolution by incorporating the streak and readout functions in one envelope thereby minimizing photon-to-charge transformations and eliminating external coupling losses is presented. The tube is based upon a grid-gated Silicon-Intensified-Target Vidicon (SITV) with integral Focus Projection Scan (FPS) TV readout. Demagnifying electron optics (m=0.63) in the image section map the 40-mm-diameter photocathode image unto a 25-mm-diameter silicon target where gains >= 103 are achieved with only 10 KV accelerating voltage. This is compared with much lower gains (~ 50) at much higher voltages (~ 30 KV) reported for streak tubes using phosphor screens. Because SIT technology is well established means for electron imaging in vacuum, such fundamental problems as "backside thinning" required for electron imaging unto CCDs do not exist. The high spatial resolution (~ 30 1p/mm), variable scan formats, and high speed electrostatic deflection (250 mm2 areas are routinely rastered with 256 scan lines in 1.6 ms) available from FPS readout add versatility not available in CCD devices. Theoretical gain and spatial resolution for this design (developed jointly by Los Alamos National Laboratory and General Electric Co.) are compared with similar calculations and measured data obtained for RCA 73435 streaks fiber optically coupled to (1) 25-mm-diameter SIT FPS vidicons and (2) 40-mm-diameter MCPTs (proximity-focused microchannel plate image intensifier tubes) fiber optically coupled to 18-mm-diameter Sb2S3 FPS vidicons. Sweep sensitivity, shutter ratio, and record lengths for nanosecond duration (20 to 200 ns) streak applications are discussed.

  13. High contrast cathode ray tube

    NASA Technical Reports Server (NTRS)

    Lisovicz, E. J.; Catlaw, T. G. (Inventor)

    1971-01-01

    A layer of material is described, which contains fine grains of phosphor material stimulated by electrons to produce visible radiation. The layer, which also contains fine grains of cobalt oxide, is deposited on the glass screen of a cathode ray tube to provide high contrast, by absorbing most of the visible radiation which is directed to the layer through the screen, while not materially affecting the visible light which the phosphor material produces in response to the electron stimulation.

  14. Par Pond vegetation status Summer 1995 -- September survey descriptive summary

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1995-09-01

    The water level of Par Pond was lowered approximately 20 feet in mid-1991 in order to protect downstream residents from possible dam failure suggested by subsidence on the downstream slope of the dam and to repair the dam. This lowering exposed both emergent and nonemergent macrophyte beds to drying conditions resulting in extensive losses. A survey of the emergent shoreline aquatic plant communities began in June 1995, three months after the refilling of Par Pond to approximately 200 feet above mean sea level and continued with this mid-September survey. Communities similar to the pre-drawdown Par Pond aquatic plant communities are becoming re-established; especially, beds of maidencane, lotus, waterlily, and watershield are now extensive and well established. Cattail occurrence continues to increase, but large beds common to Par Pond prior to the drawdown have not formed. Future surveys during the late growing seasons of 1995, and throughout 1996 and 1997, along with the evaluation of satellite data to map the areal extent of the macrophyte beds of Par Pond, are planned.

  15. Par Pond vegetation status Summer 1995 -- October survey descriptive summary

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1995-11-01

    The water level of Par Pond was lowered approximately 20 feet in mid-1991 in order to protect downstream residents from possible dam failure suggested by subsidence on the downstream slope of the dam and to repair the dam. This lowering exposed both emergent and nonemergent macrophyte beds to drying conditions resulting in extensive losses. A survey of the emergent shoreline aquatic plant communities began in June 1995, three months after the refilling of Par Pond to approximately 200 feet above mean sea level and continued with this late October survey. Communities similar to the pre-drawdown Par Pond aquatic plant communities are becoming re-established; especially, beds of maiden cane, lotus, waterlily, and watershield are now extensive and well established. Cattail occurrence continues to increase, but large beds common to Par Pond prior to the drawdown have not formed. Future surveys throughout 1996 and 1997, along with the continued evaluation of satellite data to map the areal extent of the macrophyte beds of Par Pond, are planned.

  16. Underbalanced coiled tubing sidetrack successful

    SciTech Connect

    Adam, J.; Berry, M.

    1995-12-18

    The technique of drilling through a completion string, underbalanced, with coiled tubing eliminated some of the problems encountered with overbalanced drilling in a group of offset wells. This project confirmed that performing drilling operations in live wells can be carried out safely and effectively. Dalen is a sour gas field in the eastern part of The Netherlands and produces from vertical fractures in the Zechstein carbonate reservoir. The proposal for Dalen 2 was to abandon the lower section of the original hole and subsequently sidetrack conventionally to the top of the reservoir, run and cement a 5-in. liner, complete the well with a 5-in. monobore completion, and install the christmas tree. This part of the operation would be performed with a workover hoist. Thereafter, a 3 3/4-in. hole would be drilled through the completion and into the reservoir, underbalanced with coiled tubing. The drilling proposal had to address a number of key issues: creating underbalanced conditions; handling sour gas production at surface; handling and treating drilling fluids at surface; removing drilled solids from the returned fluid system; and deploying a long coiled tubing drilling bottom hole assembly (BHA) into a live well. The paper discusses planning, legislative issues, well preparation, the drilling program, and lessons learned.

  17. Useful Scaling Parameters for the Pulse Tube

    NASA Technical Reports Server (NTRS)

    Lee, J. M.; Kittel, P.; Timmerhaus, K. D.; Radebaugh, R.; Cheng, Pearl L. (Technical Monitor)

    1995-01-01

    A set of eight non-dimensional scaling parameters for use in evaluating the performance of Pulse Tube Refrigerators is presented. The parameters result after scaling the mass, momentum and energy conservation equations for an axisymmetric, two-dimensional system. The physical interpretation of the parameters are described, and their usefulness is outlined for the enthalpy flow tube (open tube of the pulse tube). The scaling parameters allow the experimentalist to characterize three types of transport: enthalpy flow, mass streaming and heat transfer between the gas and the tube. Also reported are the results from a flow visualization experiment in which steady mass streaming in compressible oscillating flow is observed.

  18. Siphon flows in isolated magnetic flux tubes

    NASA Technical Reports Server (NTRS)

    Thomas, John H.

    1988-01-01

    The paper considers steady siphon flows in isolated thin magnetic flux tubes surrounded by field-free gas, with plasma beta greater than or equal to 1, appropriate for conditions in the solar photosphere. The cross-sectional area of the flux tube varies along the tube in response to pressure changes induced by the siphon flow. Consideration is also given to steady isothermal siphon flows in arched magnetic flux tubes in a stratified atmosphere. Applications of the results to intense magnetic flux tubes in the solar photosphere and to the photospheric Evershed flow in a sunspot penumbra are addressed.

  19. Endoscopic removal of retained T- tube fragment.

    PubMed

    Chandrasekar, Thoguluva Seshadri; Murugesh, Mallaiyappan; Radhakrishnan, Subbaiah; Sadagopan, Thiruvengadam; Hussain, Abdul Cadar Mohammed Hameed

    2009-01-01

    T-tube usage is common following common bile duct exploration for calculi and other complex biliary surgeries to ensure proper biliary diversion and healing. A 25-year-old woman was referred from a surgical unit with a history of open cholecystectomy and common bile duct exploration for cholelithiasis and choledocholithiasis with T-tube placement in the common bile duct for postoperative biliary diversion. While retrieving the T-tube, it got fractured and the fragment remained in the bile duct. We report a rare case of retained T-tube fragment after T-tube removal that was retrieved endoscopically.

  20. Endoscopic removal of retained T- tube fragment

    PubMed Central

    Chandrasekar, Thoguluva Seshadri; Murugesh, Mallaiyappan; Radhakrishnan, Subbaiah; Sadagopan, Thiruvengadam; Hussain, Abdul cadar Mohammed Hameed

    2009-01-01

    T-tube usage is common following common bile duct exploration for calculi and other complex biliary surgeries to ensure proper biliary diversion and healing. A 25-year-old woman was referred from a surgical unit with a history of open cholecystectomy and common bile duct exploration for cholelithiasis and choledocholithiasis with T-tube placement in the common bile duct for postoperative biliary diversion. While retrieving the T-tube, it got fractured and the fragment remained in the bile duct. We report a rare case of retained T-tube fragment after T-tube removal that was retrieved endoscopically. PMID:21686845

  1. [Development of salicylic acid detector tube].

    PubMed

    Ishizawa, Fujio; Kirihara, Miho; Ishiwata, Tetsuya; Yashiki, Mikio; Namera, Akira; Nishida, Manami; Kimura, Kojiro

    2004-04-01

    A detector tube was successfully devised for the screening of salicylic acid in urine. It, named "salicylic acid detector tube", consists of glass tube in which silica gel coated with 5% (w/w) of ferric chloride is enclosed. A pipette rubber cap was attached to an end of the tube, and another end was inserted into urine sample. The sample was then introduced into the tube, the color of the reagent immediately turned purple under the condition of more than 50 microg/ml of salicylic acid in urine. This device was useful for the emergency screening of salicylic acid in acute poisoning cases with aspirin.

  2. Endoscopic removal of retained T- tube fragment.

    PubMed

    Chandrasekar, Thoguluva Seshadri; Murugesh, Mallaiyappan; Radhakrishnan, Subbaiah; Sadagopan, Thiruvengadam; Hussain, Abdul Cadar Mohammed Hameed

    2009-01-01

    T-tube usage is common following common bile duct exploration for calculi and other complex biliary surgeries to ensure proper biliary diversion and healing. A 25-year-old woman was referred from a surgical unit with a history of open cholecystectomy and common bile duct exploration for cholelithiasis and choledocholithiasis with T-tube placement in the common bile duct for postoperative biliary diversion. While retrieving the T-tube, it got fractured and the fragment remained in the bile duct. We report a rare case of retained T-tube fragment after T-tube removal that was retrieved endoscopically. PMID:21686845

  3. Preparation of chitosan nanofiber tube by electrospinning.

    PubMed

    Matsuda, Atsushi; Kagata, Go; Kino, Rikako; Tanaka, Junzo

    2007-03-01

    Water-insoluble chitosan nanofiber sheets and tubes coated with chitosan-cast film were prepared by electrospinning. When as-spun chitosan nanofiber sheets and tubes were immersed in 28% ammonium aqueous solution, they became insoluble in water and showed nanofiber structures confirmed by SEM micrography. Mechanical properties of chitosan nanofiber sheets and tubes were improved by coating with chitosan-cast film, which gave them a compressive strength higher than that of crab-tendon chitosan, demonstrating that chitosan nanofiber tubes coated with chitosan-cast film are usable as nerve-regenerative guide tubes.

  4. Turbine nozzle stage having thermocouple guide tube

    DOEpatents

    Schotsch, Margaret Jones; Kirkpatrick, Francis Lawrence; Lapine, Eric Michael

    2002-01-01

    A guide tube is fixed adjacent opposite ends in outer and inner covers of a nozzle stage segment. The guide tube is serpentine in shape between the outer and inner covers and extends through a nozzle vane. An insert is disposed in the nozzle vane and has apertures to accommodate serpentine portions of the guide tube. Cooling steam is also supplied through chambers of the insert on opposite sides of a central insert chamber containing the guide tube. The opposite ends of the guide tube are fixed to sleeves, in turn fixed to the outer and inner covers.

  5. Gastroenteric tube feeding: techniques, problems and solutions.

    PubMed

    Blumenstein, Irina; Shastri, Yogesh M; Stein, Jürgen

    2014-07-14

    Gastroenteric tube feeding plays a major role in the management of patients with poor voluntary intake, chronic neurological or mechanical dysphagia or gut dysfunction, and patients who are critically ill. However, despite the benefits and widespread use of enteral tube feeding, some patients experience complications. This review aims to discuss and compare current knowledge regarding the clinical application of enteral tube feeding, together with associated complications and special aspects. We conducted an extensive literature search on PubMed, Embase and Medline using index terms relating to enteral access, enteral feeding/nutrition, tube feeding, percutaneous endoscopic gastrostomy/jejunostomy, endoscopic nasoenteric tube, nasogastric tube, and refeeding syndrome. The literature showed common routes of enteral access to include nasoenteral tube, gastrostomy and jejunostomy, while complications fall into four major categories: mechanical, e.g., tube blockage or removal; gastrointestinal, e.g., diarrhea; infectious e.g., aspiration pneumonia, tube site infection; and metabolic, e.g., refeeding syndrome, hyperglycemia. Although the type and frequency of complications arising from tube feeding vary considerably according to the chosen access route, gastrointestinal complications are without doubt the most common. Complications associated with enteral tube feeding can be reduced by careful observance of guidelines, including those related to food composition, administration rate, portion size, food temperature and patient supervision.

  6. Development boiling to sprinkled tube bundle

    NASA Astrophysics Data System (ADS)

    Kracík, Petr; Pospíšil, Jiří

    2016-03-01

    This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes' interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  7. Gastroenteric tube feeding: Techniques, problems and solutions

    PubMed Central

    Blumenstein, Irina; Shastri, Yogesh M; Stein, Jürgen

    2014-01-01

    Gastroenteric tube feeding plays a major role in the management of patients with poor voluntary intake, chronic neurological or mechanical dysphagia or gut dysfunction, and patients who are critically ill. However, despite the benefits and widespread use of enteral tube feeding, some patients experience complications. This review aims to discuss and compare current knowledge regarding the clinical application of enteral tube feeding, together with associated complications and special aspects. We conducted an extensive literature search on PubMed, Embase and Medline using index terms relating to enteral access, enteral feeding/nutrition, tube feeding, percutaneous endoscopic gastrostomy/jejunostomy, endoscopic nasoenteric tube, nasogastric tube, and refeeding syndrome. The literature showed common routes of enteral access to include nasoenteral tube, gastrostomy and jejunostomy, while complications fall into four major categories: mechanical, e.g., tube blockage or removal; gastrointestinal, e.g., diarrhea; infectious e.g., aspiration pneumonia, tube site infection; and metabolic, e.g., refeeding syndrome, hyperglycemia. Although the type and frequency of complications arising from tube feeding vary considerably according to the chosen access route, gastrointestinal complications are without doubt the most common. Complications associated with enteral tube feeding can be reduced by careful observance of guidelines, including those related to food composition, administration rate, portion size, food temperature and patient supervision. PMID:25024606

  8. Modeling Orifice Pulse Tube Coolers

    NASA Technical Reports Server (NTRS)

    Roach, Kittel P.; Roach, P. R.; Lee, J. M.; Kashani, A.; McCreight, Craig R. (Technical Monitor)

    1996-01-01

    We have developed a calculational model that treats all the components of an orifice pulse tube cooler. We base our analysis on 1-dimensional thermodynamic equations for the regenerator and we assume that all mass flows, pressure oscillations and temperature oscillations are small and sinusoidal. Non-linear pressure drop effects are included in the regenerator to account for finite pressure amplitude effects. The resulting mass flows and pressures are matched at the boundaries with the other components of the cooler: compressor, aftercooler, cold heat exchanger, pulse tube, hot heat exchanger, orifice and reservoir. The results of the calculation are oscillating pressures, mass flows and enthalpy flows in the main components of the cooler. By comparing with the calculations of other available models, we show that our model is very similar to REGEN 3 from NIST and DeltaE from Los Alamos National Lab. Our model is much easier to use than other available models because of its simple graphical interface and the fact that no guesses are required for the operating pressures or mass flows. In addition, the model only requires a few minutes of running time allowing many parameters to be optimized in a reasonable time. A version of the model is available for use over the World Wide Web at http://irtek.arc.nasa.gov. Future enhancements include adding a bypass orifice and including second order terms in steady mass streaming and steady heat transfer. A two-dimensional anelastic approximation of the fluid equations will be used as the basis for the latter analysis. Preliminary results are given in dimensionless numbers appropriate for oscillating compressible flows. The model shows how transverse heat transfer reduces enthalpy flow, particularly for small pulse tubes. The model also clearly shows mass recirculation in the open tube on the order of the tube length. They result from the higher order Reynolds stresses. An interesting result of the linearized approach is that the

  9. Precision heat forming of tetrafluoroethylene tubing

    NASA Technical Reports Server (NTRS)

    Ruiz, W. V.; Thatcher, C. S. (Inventor)

    1981-01-01

    An invention that provides a method of altering the size of tetrafluoroethylene tubing which is only available in limited combination of wall thicknesses and diameter are discussed. The method includes the steps of sliding the tetrafluoroethylene tubing onto an aluminum mandrel and clamping the ends of the tubing to the mandrel by means of clamps. The tetrafluorethylene tubing and mandrel are then placed in a supporting coil which with the mandrel and tetrafluorethylene tubing are then positioned in a insulated steel pipe which is normally covered with a fiber glass insulator to smooth out temperature distribution therein. The entire structure is then placed in an event which heats the tetrafluorethylene tubing which is then shrunk by the heat to the outer dimension of the aluminum mandrel. After cooling the aluminum mandrel is removed from the newly sized tetrafluorethylene tubing by a conventional chemical milling process.

  10. Minimum wear tube support hole design

    DOEpatents

    Glatthorn, Raymond H.

    1986-01-01

    A minimum-wear through-bore (16) is defined within a heat exchanger tube support plate (14) so as to have an hourglass configuration as determined by means of a constant radiused surface curvature (18) as defined by means of an external radius (R3), wherein the surface (18) extends between the upper surface (20) and lower surface (22) of the tube support plate (14). When a heat exchange tube (12) is disposed within the tube support plate (14) so as to pass through the through-bore (16), the heat exchange tube (12) is always in contact with a smoothly curved or radiused portion of the through-bore surface (16) whereby unacceptably excessive wear upon the heat exchange tube (12), as normally developed by means of sharp edges, lands, ridges, or the like conventionally part of the tube support plates, is eliminated or substantially reduced.

  11. The dynamics of open precipitation tubes

    NASA Astrophysics Data System (ADS)

    Kaminker, V.; Maselko, J.; Pantaleone, J.

    2014-06-01

    When a flowing fluid is channeled by chemical or physical precipitation, then tubular structures form. These patterns are common in nature, however, there have been few quantitative studies of their formation. Here, we report measurements of the radius, length, and internal pressure, as functions of time and flow rate, for precipitation tubes growing in chemical gardens. Using these measurements we develop models for how single tubes grow and also for how multiple tubes interact with each other. In particular, when multiple tubes grow from the same source they compete for resources; short/wide tubes have less resistance to flow, and so consume more of the resources, "killing" the growth of long/narrow tubes. These tube interactions are described by an equation similar to an unstable logistic equation.

  12. Vitreous occlusion of tube implant in a phakic patient with traumatic glaucoma

    PubMed Central

    Dubey, Suneeta; Pegu, Julie; Agarwal, Manisha; Agrawal, Anugya

    2014-01-01

    Tube implants or glaucoma drainage devices have become an important method of intraocular pressure reduction when treating complex cases of traumatic glaucoma. However, it is not uncommon to have complications associated with tube implants. The optimal treatment of patients who have undergone glaucoma implant surgery complicated by vitreous incarceration is uncertain. If vitreous is present or is able to prolapse into anterior chamber, as in aphakic or pseudophakic patient without an intact posterior capsule, a concurrent anterior vitrectomy is usually performed. In such cases, pars plana vitrectomy has been found to be more effective in several studies. However, there are no set guidelines for management of such a case in a phakic eye and the management can be more challenging especially when there is no obvious deficiency in posterior capsule, zonular dialysis, or loose vitreous gel in the anterior chamber prior to or during tube implantation. We describe a case of 14-year-old phakic patient with traumatic glaucoma without vitreous gel in anterior chamber whose tube implant became occluded by vitreous resulting in increased intra ocular pressure. This is the first documented report of vitreous incarceration in a phakic patient and its successful management. PMID:25378882

  13. Combined pars plana vitrectomy and Baerveldt glaucoma implant placement for refractory glaucoma

    PubMed Central

    Campagnoli, Thalmon R.; Kim, Sung Soo; Smiddy, William E.; Gedde, Steve J.; Budenz, Donald L.; Parrish, Richard K.; Palmberg, Paul F.; Feuer, William; Shi, Wei

    2015-01-01

    AIM To evaluate outcomes of combined pars plana vitrectomy and Baerveldt glaucoma implant (PPV-BGI) placement for refractory glaucoma. METHODS The medical records of 92 eyes (89 patients) that underwent PPV-BGI were retrospectively reviewed, including 43 eyes with neovascular glaucoma (NVG) and 49 eyes with other types of glaucoma (non-NVG). RESULTS Outcome measures were visual acuity (VA), intraocular pressure (IOP), glaucoma medical therapy, complications, and success [VA>hand motions (HM), IOP≥6 mm Hg and ≤21 mm Hg, no subsequent glaucoma surgery]. Cumulative success rates for the non-NVG group and NVG group were 79% and 40% at 1y, respectively (P=0.038). No difference in the rates of surgical success were found between pars plana and anterior chamber tube placement. Preoperative IOP (mean±SD) was 30.3±11.7 mm Hg in the Non-NVG group and 40.0±10.6 mm Hg in the NVG group, and IOP was reduced to 15±9.5 mm Hg in the non-NVG group and 15±10.5 mm Hg in the NVG at 1y. Number of glaucoma medications (mean±SD) decreased from 2.7±1.3 in the non-NVG group and 2.8±1.3 in the NVG group preoperatively to 0.76±1.18 in the non-NVG group and 0.51±1.00 in the NVG group at 1y. Improvement in VA of ≥2 Snellen lines was observed in 25 (27%) eyes, although only 33% of non-NVG eyes and 2.3% of NVG eyes maintained VA better than 20/200 at 1y. Nonclearing vitreous hemorrhage was the most common postoperative complication occurring in 16 (17%) eyes, and postoperative suprachoroidal hemorrhages developed in 5 (5.4%) eyes. CONCLUSION PPV-BGI is a viable surgical option for eyes with refractory glaucoma, but visual outcomes are frequently poor because of ocular comorbidities, especially in eyes with NVG. The location of tube placement does not influence surgical outcome and should be left to the discretion of the surgeon. PMID:26558201

  14. PAR-1 phosphorylates Mind bomb to promote vertebrate neurogenesis

    PubMed Central

    Ossipova, Olga; Ezan, Jerome; Sokol, Sergei Y.

    2010-01-01

    Summary Generation of neurons in the vertebrate central nervous system requires complex transcriptional regulatory network and signaling processes in polarized neuroepithelial progenitor cells. Here we demonstrate that neurogenesis in the Xenopus neural plate in vivo and mammalian neural progenitors in vitro involves intrinsic antagonistic activities of the polarity proteins PAR-1 and aPKC. Furthermore, we show that Mind bomb (Mib), a ubiquitin ligase that promotes Notch ligand trafficking and activity, is a crucial molecular substrate for PAR-1. The phosphorylation of Mib by PAR-1 results in Mib degradation, repression of Notch signaling and stimulation of neuronal differentiation. These observations suggest a conserved mechanism for neuronal fate determination that might operate during asymmetric divisions of polarized neural progenitor cells. PMID:19686683

  15. Multi-tube arrangement for combustor and method of making the multi-tube arrangement

    DOEpatents

    Ziminsky, Willy Steve

    2012-07-31

    A fuel injector tube includes a one piece, unitary, polygonal tube having an inlet end and an outlet end. The fuel injector tube further includes a fuel passage extending from the inlet end to the outlet end along a longitudinal axis of the polygonal tube, a plurality of air passages extending from the inlet end to the outlet end and surrounding the fuel passage, and a plurality of fuel holes. Each fuel hole connects an air passage with the fuel passage. The inlet end of the polygonal tube is formed into a fuel tube. A fuel injector includes a plurality of fuel injector tubes and a plate. The plurality of fuel tubes are connected to the plate adjacent the inlet ends of the plurality of fuel injector tubes.

  16. Pulse tube cooler having 1/4 wavelength resonator tube instead of reservoir

    NASA Technical Reports Server (NTRS)

    Gedeon, David R. (Inventor)

    2008-01-01

    An improved pulse tube cooler having a resonator tube connected in place of a compliance volume or reservoir. The resonator tube has a length substantially equal to an integer multiple of 1/4 wavelength of an acoustic wave in the working gas within the resonator tube at its operating frequency, temperature and pressure. Preferably, the resonator tube is formed integrally with the inertance tube as a single, integral tube with a length approximately 1/2 of that wavelength. Also preferably, the integral tube is spaced outwardly from and coiled around the connection of the regenerator to the pulse tube at a cold region of the cooler and the turns of the coil are thermally bonded together to improve heat conduction through the coil.

  17. Vacuum and the electron tube industry

    NASA Astrophysics Data System (ADS)

    Redhead, P. A.

    2005-07-01

    The electron tube industry started with the patenting of the thermionic diode by John Ambrose Fleming in 1904. The vacuum technology used by the infant tube industry was copied from the existing incandescent lamp industry. The growing demands for electron tubes for the military in the first world war led to major improvements in pumps and processing methods. By the 1920s, mass production methods were developing to satisfy the demands for receiving tubes by the burgeoning radio industry. Further expansion in the 1930s and 1940s resulted in improvements in automatic equipment for pumping vacuum tubes leading to the massive production rates of electron tubes in the second world war and the following two decades. The demand for radar during the war resulted in the development of techniques for large-scale production of microwave tubes and CRTs, the latter technology being put to good use later in TV picture tube production. The commercial introduction of the transistor ended the massive demand for receiving tubes. This review concentrates on the vacuum technology developed for receiving tube production.

  18. Counter-driver shock tube

    NASA Astrophysics Data System (ADS)

    Tamba, T.; Nguyen, T. M.; Takeya, K.; Harasaki, T.; Iwakawa, A.; Sasoh, A.

    2015-11-01

    A "counter-driver" shock tube was developed. In this device, two counter drivers are actuated with an appropriate delay time to generate the interaction between a shock wave and a flow in the opposite direction which is induced by another shock wave. The conditions for the counter drivers can be set independently. Each driver is activated by a separate electrically controlled diaphragm rupture device, in which a pneumatic piston drives a rupture needle with a temporal jitter of better than 1.1 ms. Operation demonstrations were conducted to evaluate the practical performance.

  19. Microscopic tubes in igneous rocks

    NASA Technical Reports Server (NTRS)

    Richter, D.; Simmons, G.

    1977-01-01

    Microscopic tubes have been observed in several igneous rocks and may be quite common. They occur in single crystals and have either elliptical or circular cross-sections 1 to 5 microns in diameter and are ten to hundreds of microns long. Microtubes may be hollow or partially or completely filled with another phase, but are distinct from acicular crystals of accessory minerals such as rutile. Microtubes can form by at least three processes: (1) the partial annealing of microcracks, (2) the natural etching of dislocations, or (3) the primary inclusion of fluid material during crystal growth.

  20. Cold cathode vacuum discharge tube

    DOEpatents

    Boettcher, G.E.

    1998-03-10

    A cold cathode vacuum discharge tube, and method for making same, are disclosed with an interior surface of the trigger probe coated with carbon deposited by carbon vapor deposition (CVD) or diamond-like carbon (DLC) deposition. Preferably a solid graphite insert is employed in the probe-cathode structure in place of an aluminum bushing employed in the prior art. The CVD or DLC probe face is laser scribed to allow resistance trimming to match available trigger voltage signals and to reduce electrical aging. 15 figs.

  1. Cold cathode vacuum discharge tube

    DOEpatents

    Boettcher, G.E.

    1998-04-14

    A cold cathode vacuum discharge tube, and method for making same, with an interior surface of the trigger probe coated with carbon deposited by chemical vapor deposition (CVD) or diamond-like carbon (DLC) deposition are disclosed. Preferably a solid graphite insert is employed in the probe-cathode structure in place of an aluminum bushing employed in the prior art. The CVD or DLC probe face is laser scribed to allow resistance trimming to match available trigger voltage signals and to reduce electrical aging. 14 figs.

  2. Closed End Launch Tube (CELT)

    NASA Astrophysics Data System (ADS)

    Lueck, Dale E.; Immer, Christopher D.

    2004-02-01

    A small-scale test apparatus has been built and tested for the CELT pneumatic launch assist concept presented at STAIF 2001. The 7.5 cm (3-inch) diameter × 305 M (1000 feet) long system accelerates and pneumatically brakes a 6.35 cm diameter projectile with variable weight (1.5 - 5 Kg). The acceleration and braking tube has been instrumented with optical sensors and pressure transducers at 14 stations to take data throughout the runs. Velocity and pressure profiles for runs with various accelerator pressures and projectile weights are given. This test apparatus can serve as an important experimental tool for verifying this concept.

  3. Investigation on the Inertance Tubes of Pulse Tube Cryocooler Without Reservoir

    NASA Astrophysics Data System (ADS)

    Liu, Y. J.; Yang, L. W.; Liang, J. T.; Hong, G. T.

    2010-04-01

    Phase angle is of vital importance for high-efficiency pulse tube cryocoolers (PTCs). Inertance tube as the main phase shifter is useful for the PTCs to obtain appropriate phase angle. Experiments of inertance tube without reservoir under variable frequency, variable length and diameter of inertance tube and variable pressure amplitude are investigated respectively. In addition, the authors used DeltaEC, a computer program to predict the performance of low-amplitude thermoacoustic engines, to simulate the effects of inertance tube without reservoir. According to the comparison of experiments and theoretical simulations, DeltaEC method is feasible and effective to direct and improve the design of inertance tubes.

  4. Par Pond vegetation status summer 1995 - July survey descriptive summary

    SciTech Connect

    Mackey, H.E. Jr.; Riley, R.S.

    1995-07-01

    A survey of the emergent shoreline aquatic plant, communities began in June 1995, three months after the refilling of Par Pond to approximately 200 feet (61 meters) above mean sea level, and continued with this July survey. Aquatic plant communities, similar to the pre-drawdown Par Pond communities, are becoming reestablished. Beds of maidencane (Panicum hemitomon), lotus (Nelumbo lutea), water lily (Nymphaea odorata), and watershield (Brasenia schreberi) are now extensive and well established. In addition, within isolated coves, extensive beds of water lilies and spike-rush (Eleocharis sp.) are common. Cattail occurrence has increased since refill, but large beds common to Par Pond prior to the drawdown have not formed. Invasion of willow (Salix sp.) and red maple (Acer rubrum) occurred along the lake shoreline during drawdown. The red maples along the present shoreline are beginning to show evidence of stress and mortality from flooding over the past four months. Some of the willows appear to be stressed as well. The loblolly pines (Pinus taeda), which were flooded in all but the shallow shoreline areas, are now dead. Future surveys are planned for the growing seasons of 1995, 1996, and 1997, along with the evaluation of satellite data for mapping the areal extent of the macrophyte beds of Par Pond.

  5. The Pars Triangularis in Dyslexia and ADHD: A Comprehensive Approach

    ERIC Educational Resources Information Center

    Kibby, Michelle Y.; Kroese, Judith M.; Krebbs, Hillery; Hill, Crystal E.; Hynd, George W.

    2009-01-01

    Limited research has been conducted on the structure of the pars triangularis (PT) in dyslexia despite functional neuroimaging research finding it may play a role in phonological processing. Furthermore, research to date has not examined PT size in ADHD even though the right inferior frontal region has been implicated in the disorder. Hence, one…

  6. Aqueous misdirection following pars plana vitrectomy and silicone oil injection

    PubMed Central

    Ghoraba, Hammouda H; Ghali, Ali Ahmed; Mansour, Hosam Othman

    2015-01-01

    Purpose To report a retrospective series of seven phakic eyes of seven patients suffering from a malignant glaucoma-like syndrome following pars plana vitrectomy and silicone oil (SO) injection. Materials and methods Seven eyes with retinal detachment treated with pars plana vitrectomy with or without scleral buckling with SO tamponade. This was followed by cataract extraction to manage the elevated intraocular pressure (IOP). Results This was a retrospective review of seven cases that received pars plana vitrectomy and SO with or without scleral buckling for different causes of retinal detachment (three were rhegmatogenous and four were tractional). After a period ranging from 1 week to 1 month, they presented with malignant glaucoma-like manifestations; high IOP, shallow axial anterior chamber, and remarkable decrease of visual acuity. Atropine eye drops and anti-glaucoma medical treatment (topical and systemic) had been tried but failed to improve the condition. Dramatic decrease of IOP and deepening of the axial anterior chamber was observed in all cases in the first postoperative day after phacoemulsification and posterior chamber foldable intraocular lens implantation with posterior capsulotomy. Conclusion Aqueous misdirection syndrome may be observed following pars plana vitrectomy and SO tamponade. This must be differentiated from other causes of post vitrectomy glaucoma. Cataract extraction with posterior capsulotomy controls the condition. PMID:26056429

  7. Radiological impact of Par Pond drawdown from liquid effluent pathways

    SciTech Connect

    Carlton, W.H.; Hamby, D.M.

    1991-10-25

    The water level of Par Pond has been lowered over the past several months to reduce the effects in the event of catastrophic dam failure while assessing the condition of the dam and determining if repairs are necessary. In lowering the level of Par Pond, 60 billion liters of water containing low levels of tritium and cesium-137 were discharged to several onsite streams. SRS surface streams flow to the Savannah River. An assessment made to determine the total amount of tritium and Cs-137 discharged and to estimate the consequences to downstream Savannah River users. It is estimated that a total of 160 curies of tritium were displaced from Par Pond to the Savannah River between June 28, 1991 and September 19, 1991. This release could hypothetically result in a maximum individual dose of 3. 2{times}10{sup {minus}4} mrem and a total (80-km and drinking water populations) population dose of 1.4{times}10{sup {minus}2} person-rem. Likewise, a maximum individual dose of 5.0{times}10{sup {minus}2} mrem and a total population dose of 1.7{times}10{sup {minus}1} person- rem are predicted as a result of an estimated 0.21 curies of Cs-137 being discharged from Par Pond to the Savannah River.

  8. BOREAS RSS-10 TOMS Circumpolar One-Degree PAR Images

    NASA Technical Reports Server (NTRS)

    Dye, Dennis G.; Holben, Brent; Nickeson, Jaime (Editor); Hall, Forrest G. (Editor); Smith, David E. (Technical Monitor)

    2000-01-01

    The Boreal Ecosystem-Atmosphere Study (BOREAS) Remote Sensing Science (RSS)-10 team investigated the magnitude of daily, seasonal, and yearly variations of Photosynthetically Active Radiation (PAR) from ground and satellite observations. This data set contains satellite estimates of surface-incident PAR (400-700 nm, MJ/sq m) at one-degree spatial resolution. The spatial coverage is circumpolar from latitudes of 41 to 66 degrees north. The temporal coverage is from May through September for years 1979 through 1989. Eleven-year statistics are also provided: (1) mean, (2) standard deviation, and (3) coefficient of variation for 1979-89. The PAR estimates were derived from the global gridded ultraviolet reflectivity data product (average of 360, 380 nm) from the Nimbus-7 Total Ozone Mapping Spectrometer (TOMS). Image mask data are provided for identifying the boreal forest zone, and ocean/land and snow/ice-covered areas. The data are available as binary image format data files. The PAR data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

  9. Competing ParA structures space bacterial plasmids equally over the nucleoid.

    PubMed

    Ietswaart, Robert; Szardenings, Florian; Gerdes, Kenn; Howard, Martin

    2014-12-01

    Low copy number plasmids in bacteria require segregation for stable inheritance through cell division. This is often achieved by a parABC locus, comprising an ATPase ParA, DNA-binding protein ParB and a parC region, encoding ParB-binding sites. These minimal components space plasmids equally over the nucleoid, yet the underlying mechanism is not understood. Here we investigate a model where ParA-ATP can dynamically associate to the nucleoid and is hydrolyzed by plasmid-associated ParB, thereby creating nucleoid-bound, self-organizing ParA concentration gradients. We show mathematically that differences between competing ParA concentrations on either side of a plasmid can specify regular plasmid positioning. Such positioning can be achieved regardless of the exact mechanism of plasmid movement, including plasmid diffusion with ParA-mediated immobilization or directed plasmid motion induced by ParB/parC-stimulated ParA structure disassembly. However, we find experimentally that parABC from Escherichia coli plasmid pB171 increases plasmid mobility, inconsistent with diffusion/immobilization. Instead our observations favor directed plasmid motion. Our model predicts less oscillatory ParA dynamics than previously believed, a prediction we verify experimentally. We also show that ParA localization and plasmid positioning depend on the underlying nucleoid morphology, indicating that the chromosomal architecture constrains ParA structure formation. Our directed motion model unifies previously contradictory models for plasmid segregation and provides a robust mechanistic basis for self-organized plasmid spacing that may be widely applicable.

  10. Tube support grid and spacer therefor

    DOEpatents

    Ringsmuth, Richard J.; Kaufman, Jay S.

    1986-01-01

    A tube support grid and spacers therefor provide radially inward preloading of heat exchange tubes to minimize stress upon base welds due to differential thermal expansion. The grid comprises a concentric series of rings and spacers with opposing concave sides for conforming to the tubes and V-shaped ends to provide resilient flexibility. The flexibility aids in assembly and in transmitting seismic vibrations from the tubes to a shroud. The tube support grid may be assembled in place to achieve the desired inwardly radial preloading of the heat exchange tubes. Tab and slot assembly further minimizes stresses in the system. The radii of the grid rings may be preselected to effect the desired radially inward preloading.

  11. Large Diameter Lasing Tube Cooling Arrangement

    DOEpatents

    Hall, Jerome P.; Alger, Terry W.; Anderson, Andrew T.; Arnold, Philip A.

    2004-05-18

    A cooling structure (16) for use inside a ceramic cylindrical tube (11) of a metal vapor laser (10) to cool the plasma in the tube (11), the cooling structure (16) comprising a plurality of circular metal members (17,31) and mounting members (18, 34) that position the metal members (17,31) coaxially in the tube (11) to form an annular lasing volume, with the metal members (17, 31) being axially spaced from each other along the length of the tube (11) to prevent the metal members from shorting out the current flow through the plasma in the tube (11) and to provide spaces through which the heat from localized hot spots in the plasma may radiate to the other side of the tube (11).

  12. Large diameter lasing tube cooling arrangement

    DOEpatents

    Hall, Jerome P.; Alger, Terry W.; Anderson, Andrew T.; Arnold, Phillip A.

    2004-05-18

    A cooling structure (16) for use inside a ceramic cylindrical tube (11) of a metal vapor laser (10) to cool the plasma in the tube (11), the cooling structure (16) comprising a plurality of circular metal members (17, 31) and mounting members (18, 34) that position the metal members (17, 31) coaxially in the tube (11) to form an annular lasing volume, with the metal members (17, 31) being axially spaced from each other along the length of the tube (11) to prevent the metal members from shorting out the current flow through the plasma in the tube (11) and to provide spaces through which the heat from localized hot spots in the plasma may radiate to the other side of the tube (11).

  13. On Flow Stagnation in a Tube Radiator

    NASA Technical Reports Server (NTRS)

    Motil, Brian; Chao, David F.; Sankovic, John M.; Zhang, Nengli

    2007-01-01

    An analysis of the physical process for occurrence of flow stagnation in a space tube-radiator is performed and the mechanism and mathematic description for the flow stagnation are presented. Two causes for pressure drop unbalance between tubes of the radiator are identified: non-uniform cooling environment and different local flow resistances between the tubes. This analysis provides a theoretical basis for experimental simulations of the flow stagnation in a ground-based lab as well as two suggested methods to experimentally simulate flow stagnation. Criteria for the flow stagnation, depending on the viscosity data regressive polynomial, are derived from the extreme condition of the pressure drop in colder tubes. A preliminary numerical calculation is conducted for a space tube-radiator model which confirms the physical and mathematical analyses. The prediction by the criteria for flow stagnation in the tube-radiator model coincides with the numerical calculation result.

  14. Various factors affect coiled tubing limits

    SciTech Connect

    Yang, Y.S.

    1996-01-15

    Safety and reliability remain the primary concerns in coiled tubing operations. Factors affecting safety and reliability include corrosion, flexural bending, internal (or external) pressure and tension (or compression), and mechanical damage due to improper use. Such limits as coiled tubing fatigue, collapse, and buckling need to be understood to avoid disaster. With increased use of coiled tubing, operators will gain more experience. But at the same time, with further research and development of coiled tubing, the manufacturing quality will be improved and fatigue, collapse, and buckling models will become more mature, and eventually standard specifications will be available. This paper reviews the uses of coiled tubing and current research on mechanical behavior of said tubing. It also discusses several models used to help predict fatigue and failure levels.

  15. ParA-mediated plasmid partition driven by protein pattern self-organization

    PubMed Central

    Hwang, Ling Chin; Vecchiarelli, Anthony G; Han, Yong-Woon; Mizuuchi, Michiyo; Harada, Yoshie; Funnell, Barbara E; Mizuuchi, Kiyoshi

    2013-01-01

    DNA segregation ensures the stable inheritance of genetic material prior to cell division. Many bacterial chromosomes and low-copy plasmids, such as the plasmids P1 and F, employ a three-component system to partition replicated genomes: a partition site on the DNA target, typically called parS, a partition site binding protein, typically called ParB, and a Walker-type ATPase, typically called ParA, which also binds non-specific DNA. In vivo, the ParA family of ATPases forms dynamic patterns over the nucleoid, but how ATP-driven patterning is involved in partition is unknown. We reconstituted and visualized ParA-mediated plasmid partition inside a DNA-carpeted flowcell, which acts as an artificial nucleoid. ParA and ParB transiently bridged plasmid to the DNA carpet. ParB-stimulated ATP hydrolysis by ParA resulted in ParA disassembly from the bridging complex and from the surrounding DNA carpet, which led to plasmid detachment. Our results support a diffusion-ratchet model, where ParB on the plasmid chases and redistributes the ParA gradient on the nucleoid, which in turn mobilizes the plasmid. PMID:23443047

  16. PH motifs in PAR1&2 endow breast cancer growth.

    PubMed

    Kancharla, A; Maoz, M; Jaber, M; Agranovich, D; Peretz, T; Grisaru-Granovsky, S; Uziely, B; Bar-Shavit, R

    2015-01-01

    Although emerging roles of protease-activated receptor1&2 (PAR1&2) in cancer are recognized, their underlying signalling events are poorly understood. Here we show signal-binding motifs in PAR1&2 that are critical for breast cancer growth. This occurs via the association of the pleckstrin homology (PH) domain with Akt/PKB as a key signalling event of PARs. Other PH-domain signal-proteins such as Etk/Bmx and Vav3 also associate with PAR1 and PAR2 through their PH domains. PAR1 and PAR2 bind with priority to Etk/Bmx. A point mutation in PAR2, H349A, but not in R352A, abrogates PH-protein association and is sufficient to markedly reduce PAR2-instigated breast tumour growth in vivo and placental extravillous trophoblast (EVT) invasion in vitro. Similarly, the PAR1 mutant hPar1-7A, which is unable to bind the PH domain, reduces mammary tumours and EVT invasion, endowing these motifs with physiological significance and underscoring the importance of these previously unknown PAR1 and PAR2 PH-domain-binding motifs in both pathological and physiological invasion processes. PMID:26600192

  17. PH motifs in PAR1&2 endow breast cancer growth

    PubMed Central

    Kancharla, A.; Maoz, M.; Jaber, M.; Agranovich, D.; Peretz, T.; Grisaru-Granovsky, S.; Uziely, B.; Bar-Shavit, R.

    2015-01-01

    Although emerging roles of protease-activated receptor1&2 (PAR1&2) in cancer are recognized, their underlying signalling events are poorly understood. Here we show signal-binding motifs in PAR1&2 that are critical for breast cancer growth. This occurs via the association of the pleckstrin homology (PH) domain with Akt/PKB as a key signalling event of PARs. Other PH-domain signal-proteins such as Etk/Bmx and Vav3 also associate with PAR1 and PAR2 through their PH domains. PAR1 and PAR2 bind with priority to Etk/Bmx. A point mutation in PAR2, H349A, but not in R352A, abrogates PH-protein association and is sufficient to markedly reduce PAR2-instigated breast tumour growth in vivo and placental extravillous trophoblast (EVT) invasion in vitro. Similarly, the PAR1 mutant hPar1-7A, which is unable to bind the PH domain, reduces mammary tumours and EVT invasion, endowing these motifs with physiological significance and underscoring the importance of these previously unknown PAR1 and PAR2 PH-domain-binding motifs in both pathological and physiological invasion processes. PMID:26600192

  18. Refractory shield for superheater tubes

    SciTech Connect

    Green, K.E.; Johnson, D.K.; Woodruff, R.W.

    1987-07-28

    A refractory shield is described for protecting superheater tubes against attack by the products of combustion comprising: a pair of elongated molded and fired refractory half shields of predetermined identical interchangeable interlocking size and shape adapted when one of the half shields is rotated 180/sup 0/ and extends longitudinally relative to the other half shields to be slid axially together and interlocked together solely without additional fastening means, surround and shield the superheater tube. Each half shield has: an elongated refractory sidewall portion of predetermined axial length and thickness between opposite ends extending circumferentially between and to diametrically opposite refractory tongue and grooved side wall portions of predetermined axially engageable interlocking shape. An elongated tongue of predetermined shape, width and radial length projects radially outwardly from the tongue sidewall portion; and an elongated internal groove projects radially outward in the grooved side wall portion and of predetermined interlocking shape. Sufficient width and radial depth accept an elongated tongue of the other one of the pair of half shields assembled and locked together against relative rotation solely by axially inserting the tongues into the grooves.

  19. Making Internal Molds Of Long, Curved Tubes

    NASA Technical Reports Server (NTRS)

    Burley, Richard K.

    1989-01-01

    Mold material carried to internal weld joint and removed after impression taken. Remotely operated device makes impression mold of interior surface of tube at weld joint. Mold provides indication of extent of mismatch between members at joint. Maneuvered to weld inspected through curved tube 3 in. in diameter by 50 in. long. Readily adapted to making molds to measure depth of corrosion in boiler tubes or other pipes.

  20. Joining of tubes by gas detonation forming

    NASA Astrophysics Data System (ADS)

    Jenkouk, Vahid; Patil, Sandeep; Markert, Bernd

    2016-08-01

    For many applications, such as in structural components, it is required to join two tubes - sometimes with dissimilar material properties. Only few research studies have investigated the joining of tubular metallic components by means of high-velocity forming processes. In this paper, we present the novel process of joining of two tubes by a gas detonation pressure wave. In particular, the joining of a copper and a steel tube is discussed by means of a finite element study and a conducted experiment.

  1. Hand-Operated Hydraulic Tube Expander

    NASA Technical Reports Server (NTRS)

    Hagan, David W.; Wolff, Edwin D.

    1995-01-01

    Hand-operated tool expands end portion of narrow metal or plastic tube to slightly larger diameter. Used on tubes with original inner diameters as small as 0.060 in. Includes replaceable tip comprising ferrule and tubular expansion sleeve sized for sliding fit into tube to be expanded. Expansion sleeve swells in response to internal hydraulic pressure generated by turning handle and thereby advancing piston.

  2. Preparation of nitrogen-doped carbon tubes

    SciTech Connect

    Chung, Hoon Taek; Zelenay, Piotr

    2015-12-22

    A method for synthesizing nitrogen-doped carbon tubes involves preparing a solution of cyanamide and a suitable transition metal-containing salt in a solvent, evaporating the solvent to form a solid, and pyrolyzing the solid under an inert atmosphere under conditions suitable for the production of nitrogen-doped carbon tubes from the solid. Pyrolyzing for a shorter period of time followed by rapid cooling resulted in a tubes with a narrower average diameter.

  3. Hose- and Tube-Cleaning Module

    NASA Technical Reports Server (NTRS)

    Rollins, F. P.; Glass, J. S.

    1986-01-01

    Self-contained, single-use module enables hose or tube to be cleaned thoroughly in field, in one operation, using water of unknown or questionable quality. Previously, chemicals for flow cleaning had to be mixed, diluted and pumped through tubes and hoses in many successive steps; deionizers, water-treatment facilities, and chemical storage required. With proposed device cleaning performed safely, without special training. Ready to use, device packaged as cleaning kit with tube to be cleaned.

  4. Comparative Tests of Pitot-static Tubes

    NASA Technical Reports Server (NTRS)

    Merriam, Kenneth G; Spaulding, Ellis R

    1935-01-01

    Comparative tests were made on seven conventional Pitot-static tubes to determine their static, dynamic, and resultant errors. The effect of varying the dynamic opening, static opening, wall thickness, and inner-tube diameter was investigated. Pressure-distribution measurements showing stem and tip effects were also made. A tentative design for a standard Pitot-static tube for use in measuring air velocity is submitted.

  5. Results of peripheral laser photocoagulation in pars planitis.

    PubMed Central

    Pulido, J S; Mieler, W F; Walton, D; Kuhn, E; Postel, E; Hartz, A; Jampol, L M; Weinberg, D V; Logani, S

    1998-01-01

    PURPOSE: To determine the effect of peripheral retinal laser photocoagulation (PLP) on visual acuity, intraocular inflammation, and other ocular findings, including retinal neovascularization in eyes with pars planitis. METHODS: A retrospective chart review of eyes with pars planitis that had undergone PLP. RESULTS: Twenty-two eyes in 17 patients with pars planitis had undergone treatment with PLP at 2 centers. The mean age at the time of treatment was 19.3 years. Following treatment, mean follow-up was 16.3 months (range, 6 to 37 months). Mean visual acuity was 20/60 preoperatively and 20/50 postoperatively. This level of improvement was not statistically significant (P > .10), but there was a statistically significant decrease in the use of corticosteroids between the preoperative examination and the last postoperative examination (86% versus 27%, P < .05). There was also a statistically significant decrease in vitritis at the last follow-up (P = .0008) and a decrease in neovascularization of the vitreous base (P = .03) and in clinically apparent cystoid macular edema (P = .02). Epiretinal membranes were noted in 23% of eyes preoperatively and in 45% of eyes postoperatively. Only one of these epiretinal membranes was considered to be visually significant. One eye developed a tonic dilated pupil, which slowly improved. CONCLUSIONS: Although the long-term natural history of clinical findings in pars planitis is not well documented, PLP appears to decrease the need for corticosteroids while stabilizing visual acuity. It also appears to decrease vitreous inflammation. PLP has few complications and should be considered in patients with pars planitis who are unresponsive or have adverse reactions to corticosteroids. PMID:10360286

  6. The nasogastric tube syndrome in infants.

    PubMed

    Harmon, Jeffrey; Balakrishnan, Karthik; de Alarcon, Alessandro; Hart, Catherine K

    2014-05-01

    This series of three patients is the first description of the presentation, clinical course, and endoscopic findings of nasogastric tube-related airway distress, or nasogastric tube syndrome, in infants. We identify key differences in disease features from those described in adults, based on our literature review. Specifically, infant nasogastric tube syndrome presented as significant respiratory distress and postcricoid inflammation without vocal fold immobility. Symptoms resolved more quickly (mean±SD, 2±1 days) than reported in adults. We suggest that nasogastric tube syndrome should be considered in infants with otherwise unexplained respiratory distress, even in the absence of impaired vocal fold mobility.

  7. Simplified Explosive Joining of Tubes to Fittings

    NASA Technical Reports Server (NTRS)

    Bement, L. J.; Bailey, J. W.; Perry, R.; Finch, M. S.

    1987-01-01

    Technique simplifies tube-to-fitting joining, as compared to fusion welding, and provides improvement on standard procedures used to join tubes explosively to tube fittings. Special tool inserted into tube to be joined. Tool allows strip of ribbon explosive to be placed right at joint. Ribbon explosive and mild detonating fuse allows use of smaller charge. Assembled tool storable, and process amenable to automation. Assembly of components, insertion of tool into weld site, and joining operation mechanized without human contact. Used to assemble components in nuclear reactors or in other environments hostile to humans.

  8. The structure of photospheric flux tubes

    NASA Technical Reports Server (NTRS)

    Thomas, John H.

    1990-01-01

    Basic physical mechanisms for producing the observed intense magnetic flux tubes in the solar photosphere are reviewed. The mechanism of flux expulsion by convective cells can concentrate magnetic flux up to the equipartition field strength, which is only about 200 G at the solar surface for the observed granular convection. Other mechanisms that partially evacuate the flux tube are needed to produce further concentration of magnetic flux to the observed values of 1000-1500 G. Two such mechanisms are discussed: concentration by convective collapse of a vertical flux tube in the superadiabatic layer just below the solar surface, and concentration by a siphon flow in an arched, isolated flux tube.

  9. Modeling Pulse Tube Cryocoolers with CFD

    NASA Astrophysics Data System (ADS)

    Flake, Barrett; Razani, Arsalan

    2004-06-01

    A commercial computational fluid dynamics (CFD) software package is used to model the oscillating flow inside a pulse tube cryocooler. Capabilities for modeling pulse tubes are demonstrated with preliminary case studies and the results presented. The 2D axi-symmetric simulations demonstrate the time varying temperature and velocity fields in the tube along with computation of the heat fluxes at the hot and cold heat exchangers. The only externally imposed boundary conditions are a cyclically moving piston wall at one end of the tube and constant temperature or heat flux boundaries at the external walls of the hot and cold heat exchangers.

  10. Reducing gain shifts in photomultiplier tubes

    DOEpatents

    Cohn, Charles E.

    1976-01-01

    A means is provided for reducing gain shifts in multiplier tubes due to varying event count rates. It includes means for limiting the number of cascaded, active dynodes of the multiplier tube to a predetermined number with the last of predetermined number of dynodes being the output terminal of the tube. This output is applied to an amplifier to make up for the gain sacrificed by not totally utilizing all available active stages of the tube. Further reduction is obtained by illuminating the predetermined number of dynodes with a light source of such intensity that noise appearing at the output dynode associated with the illumination is negligible.

  11. Acoustic resonance in heat exchanger tube bundles

    SciTech Connect

    Blevins, R.D. )

    1994-02-01

    A series of experiments has been made on aeroacoustic tones produced by flow over tubes in a duct. The sound is characterized by the onset of a loud and persistent acoustic resonance. The acoustic resonance occurs at the frequency of the acoustic modes. The magnitude and extent of the resonance are functions of tube pattern and tube pitch. The sound levels increase in proportion with Mach number, dynamic head and pressure drop. A design procedure for predicting the magnitude of the sound within the tube array is presented. Methods of resonance avoidance are illustrated. An example is made for a large petrochemical heat exchanger.

  12. Benchmarking boiler tube failures - Part 1

    SciTech Connect

    Patrick, J.; Oldani, R.; von Behren, D.

    2005-10-01

    Boiler tube failures continue to be the leading cause of downtime for steam power plants. That should not be a surprise; a typical steam generator has miles of tubes that operate at high temperatures and pressures. Are your experiences comparable to those of your peers? Could you learn something from tube-leak benchmarking data that could improve the operation of your plant? The Electric Utility Cost Group (EUCG) recently completed a boiler-tube failure study that is available only to its members. But Power magazine has been given exclusive access to some of the results, published in this article. 4 figs.

  13. True Color Tube Borescope Inspection System

    SciTech Connect

    Harpring, Larry J.

    1997-08-07

    The overall purpose of TCTBIS is to determine the quality of the inside surface of a tube. This is done by acquiring multiple images along the inside of a tube and converting these images into one unwrapped image of the inside of a tube. This resultant image is the same as if you had slit a tube length-wise, flattened it out, and then taken a picture of it. What is unique about this system is that the picture is acquired in a non-destructive manner. TCTBIS also analyzes the unwrapped images for oxidation, foreign particles, and surface imperfections, scratches.

  14. TCTBIS. True Color Tube Borescope Inspection System

    SciTech Connect

    Harpring, L.

    1997-05-20

    The overall purpose of TCTBIS is to determine the quality of the inside surface of a tube. This is done by acquiring multiple images along the inside of a tube and converting these images into one unwrapped image of the inside of a tube. This resultant image is the same as if you had slit a tube length-wise, flattened it out, and then taken a picture of it. What is unique about this system is that the picture is acquired in a non-destructive manner. TCTBIS also analyzes the unwrapped images for oxidation, foreign particles, and surface imperfections, scratches.

  15. Screening for Open Neural Tube Defects.

    PubMed

    Krantz, David A; Hallahan, Terrence W; Carmichael, Jonathan B

    2016-06-01

    Biochemical prenatal screening was initiated with the use of maternal serum alpha fetoprotein to screen for open neural tube defects. Screening now includes multiple marker and sequential screening protocols involving serum and ultrasound markers to screen for aneuploidy. Recently cell-free DNA screening for aneuploidy has been initiated, but does not screen for neural tube defects. Although ultrasound is highly effective in identifying neural tube defects in high-risk populations, in decentralized health systems maternal serum screening still plays a significant role. Abnormal maternal serum alpha fetoprotein alone or in combination with other markers may indicate adverse pregnancy outcome in the absence of open neural tube defects. PMID:27235920

  16. Solar power absorption in a glass tube

    NASA Technical Reports Server (NTRS)

    Williams, Michael D.

    1987-01-01

    The optics of a glass tube to be used in near-Earth space at the focus of a solar concentrator has been examined, and an equation for the power absorbed from multiple-reflected light beams in the tube wall has been developed. The equation has been used to calculate the power absorbed by a highly transmissive form of fused silica. The equilibrium temperature reached by the tube with only radiative cooling has also been examined, and it shows a significant rise with large solar concentrations. The results apply specifically to cylindrical containment vessels for space-based solar-pumped lasers and generally to any similarly irradiated tubes.

  17. True Color Tube Borescope Inspection System

    1997-08-07

    The overall purpose of TCTBIS is to determine the quality of the inside surface of a tube. This is done by acquiring multiple images along the inside of a tube and converting these images into one unwrapped image of the inside of a tube. This resultant image is the same as if you had slit a tube length-wise, flattened it out, and then taken a picture of it. What is unique about this system ismore » that the picture is acquired in a non-destructive manner. TCTBIS also analyzes the unwrapped images for oxidation, foreign particles, and surface imperfections, scratches.« less

  18. GEIGER-MULLER TYPE COUNTER TUBE

    DOEpatents

    Fowler, I.L.; Watt, L.A.K.

    1959-12-15

    A single counter tube capable of responding to a wide range of intensities is described. The counter tube comprises a tubular cathode and an anode extending centrally of the cathode. The spacing between the outer surface of the anode and the inner surface of the cathode is varied along the length of the tube to provide different counting volumes in adjacent portions of the tube. A large counting volume in one portion adjacent to a low-energy absorption window gives adequate sensitivity for measuring lowintensity radiation, while a smaller volume with close electrode spacing is provided in the counter to make possible measurement of intense garnma radiation fields.

  19. Eddy current measurement of tube element spacing

    DOEpatents

    Latham, Wayne Meredith; Hancock, Jimmy Wade; Grut, Jayne Marie

    1998-01-01

    A method of electromagnetically measuring the distance between adjacent tube elements in a heat exchanger. A cylindrical, high magnetic permeability ferrite slug is placed in the tube adjacent the spacing to be measured. A bobbin or annular coil type probe operated in the absolute mode is inserted into a second tube adjacent the spacing to be measured. From prior calibrations on the response of the eddy current coil, the signals from the coil, when sensing the presence of the ferrite slug, are used to determine the spacing between the tubes.

  20. Small bowel perforation during suprapubic tube exchange.

    PubMed

    Mongiu, Anne K; Helfand, Brain T; Kielb, Stephanie J

    2009-02-01

    Suprapubic tube placement is a common urological procedure with a low incidence of complications, including hematuria, catheter blockage, recurrent urinary tract infections, and rarely, injury to adjacent organs. Fortunately, most serious complications are discovered shortly after initial suprapubic tube placement and are readily corrected. Very few cases of delayed complications or injuries have been reported. We report a case of Foley perforation into the ileum during suprapubic tube exchange discovered more than 8 months after initial placement, and preceding numerous monthly changes that occurred without incident. While a rare complication, physicians should be conscious of the potential for delayed injury in patients managed with long term suprapubic tube placement. PMID:19222896

  1. Eddy-Current Detection of Cracks in Tubes

    NASA Technical Reports Server (NTRS)

    Parent, R.; Kettering, D.

    1987-01-01

    Nondestructive device tests narrow, sharply-bent metal tubes. Eddycurrent probe detects incipient cracks inside small metal tubes. Tube-centering device consisting of pair of opposed bars ensures tube centered on eddy-current coil. Probe moves along length of bent tube to inspect repeatably for cracks. Compatible with tubes of different cross sections, oval, flattened, square, rectangular,or irregular. Adapts for inspecting formed tubes in petrochemical, automotive, nuclear, and medical equipment.

  2. Performance of multi tubes in tube helically coiled as a compact heat exchanger

    NASA Astrophysics Data System (ADS)

    Nada, S. A.; El Shaer, W. G.; Huzayyin, A. S.

    2014-12-01

    Multi tubes in tube helically coiled heat exchanger is proposed as a compact heat exchanger. Effects of heat exchanger geometric parameters and fluid flow parameters; namely number of inner tubes, annulus hydraulic diameter, Reynolds numbers and input heat flux, on performance of the heat exchanger are experimentally investigated. Different coils with different numbers of inner tubes, namely 1, 3, 4 and 5 tubes, were tested. Results showed that coils with 3 inner tubes have higher values of heat transfer coefficient and compactness parameter (bar{h} Ah ). Pressure drop increases with increasing both of Reynolds number and number of inner tubes. Correlations of average Nusselt number were deduced from experimental data in terms of Reynolds number, Prandtl number, Number of inner coils tubes and coil hydraulic diameter. Correlations prediction was compared with experimental data and the comparison was fair enough.

  3. Generation of flux tube waves in stellar convection zones. 1: Longitudinal tube waves

    NASA Technical Reports Server (NTRS)

    Musielak, Z. E.; Rosner, R.; Ulmschneider, P.

    1987-01-01

    The source functions and the energy fluxes are derived for wave generation in magnetic flux tubes embedded in an otherwise magnetic- field free, turbulent, and compressible fluid. Specific results for the generation of longitudinal tube waves are presented.

  4. Tube Thoracostomy (Chest Tube) Removal in Traumatic Patients: What Do We Know? What Can We Do?

    PubMed Central

    Paydar, Shahram; Ghahramani, Zahra; Ghoddusi Johari, Hamed; Khezri, Samad; Ziaeian, Bizhan; Ghayyoumi, Mohammad Ali; Fallahi, Mohammad Javad; Niakan, Mohammad Hadi; Sabetian, Golnar; Abbasi, Hamid Reza; Bolandparvaz, Shahram

    2015-01-01

    Chest tube (CT) or tube thoracostomy placement is often indicated following traumatic injuries. Premature movement of the chest tube leads to increased hospital complications and costs for patients. Placement of a chest tube is indicated in drainage of blood, bile, pus, drain air, and other fluids. Although there is a general agreement for the placement of a chest tube, there is little consensus on the subsequent management. Chest tube removal in trauma patients increases morbidity and hospital expense if not done at the right time. A review of relevant literature showed that the best answers to some questions about time and decision-making have been long sought. Issues discussed in this manuscript include chest tube removal conditions, the need for chest radiography before and after chest tuberemoval, the need to clamp the chest tube prior to removal, and drainage rate and acceptability prior to removal. PMID:27162900

  5. The role of pars flaccida in human middle ear sound transmission.

    PubMed

    Aritomo, H; Goode, R L; Gonzalez, J

    1988-04-01

    The role of the pars flaccida in middle ear sound transmission was studied with the use of twelve otoscopically normal, fresh, human temporal bones. Peak-to-peak umbo displacement in response to a constant sound pressure level at the tympanic membrane was measured with a noncontacting video measuring system capable of repeatable measurements down to 0.2 micron. Measurements were made before and after pars flaccida modifications at 18 frequencies between 100 and 4000 Hz. Four pars flaccida modifications were studied: (1) acoustic insulation of the pars flaccida to the ear canal with a silicone rubber baffle, (2) stiffening the pars flaccida with cyanoacrylate cement, (3) decreasing the tension of the pars flaccida with a nonperforating incision, and (4) perforation of the pars flaccida. All of the modifications (except the perforation) had a minimal effect on umbo displacement; this seems to imply that the pars flaccida has a minor acoustic role in human beings. PMID:3132684

  6. A secure method of nasal endotracheal tube stabilization with suture and rubber tube.

    PubMed

    Ota, Y; Karakida, K; Aoki, T; Yamazaki, H; Arai, I; Mori, Y; Nakatogawa, N; Suzuki, T

    2001-12-01

    A new method of stabilizing the nasal endotrascheal tube was described. The tube was secured to the anterior portion of the nasal septum with braided silk thread, which was tightened over the rubber tube to keep air route of the cuff open. There found no complications such as unplanned extubation, necrosis and infections of the nasal septum.

  7. Pool boiling of R-114/oil mixtures from single tubes and tube bundles. Master's thesis

    SciTech Connect

    Murphy, T.J.

    1987-09-01

    An apparatus was designed, fabricated, and operated for the testing of horizontal tube bundles for boiling of R-114 with various concentrations of oil. Preliminary data were taken on the top tube in the bundle, with and without the other tubes in operation. Results showed up to a 37% increase in the boiling heat-transfer coefficient as a result of the favorable bundle effect. In a separate single-tube apparatus, three enhanced tubes were tested at a saturation temperature of 2.2 C with oil mass concentrations of 0, 1, 2, 3, 6 and 10%. The tubes were: 1) a finned tube with 1024 fins per meter, 2) a finned tube with 1575 fins per meter and 3) a Turbo-B tube. These tubes resulted in enhancement ratios in pure refrigerant of 2.8, 3.8 and 5.2, respectively, at a practical heat flux of 30 kW/sq. meter. With 3% oil, these ratios were decreased to 2.6, 3.5 and 5, while with 10% oil, these ratios were further reduced to 2.6, 3.2 and 4.7, respectively. Based on these results, the use of Turbo-B tubes is expected to result in significant savings in weight and size of evaporators over the finned tubes presently in use on board some naval vessels.

  8. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and... for the service intended at the MAWP specified on the boiler specification FRA Form No. 4, they...

  9. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and... for the service intended at the MAWP specified on the boiler specification FRA Form No. 4, they...

  10. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and... for the service intended at the MAWP specified on the boiler specification FRA Form No. 4, they...

  11. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and... for the service intended at the MAWP specified on the boiler specification FRA Form No. 4, they...

  12. 49 CFR 230.61 - Arch tubes, water bar tubes, circulators and thermic siphons.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.61 Arch tubes, water bar tubes, circulators and thermic siphons. (a) Frequency of cleaning. Each time the boiler is washed, arch tubes and... for the service intended at the MAWP specified on the boiler specification FRA Form No. 4, they...

  13. Uptake of Nitroaromatic Compounds by Polymeric Tubing

    SciTech Connect

    BOUNKEUA, VIENGNGEUN; RODACY, PHILIP J.

    2001-04-01

    The type of polymeric material used in the manufacturing of tubing determines its strength, elasticity, and durability. Tubing made of polymeric material is commonly used for analytical work because it is readily available, inexpensive and can be relatively inert. Polymeric tubing is used in many sampling applications for explosive compounds. A major concern is the uptake of the explosive compounds into or onto the tubing during sampling. Because of the reactive nature of explosives, it is important that as little of the detectable explosive as possible is lost by tubing uptake. It is also important that nothing leaches out of the tubing to interfere with the detection of explosives. High Performance Liquid Chromatography (HPLC) is commonly used for the analysis of trace levels of explosive compounds in the range of parts per billion (ppb) to parts per million (ppm). This study attempts to determine which types of polymers are most conducive to sampling applications where large volumes of dilute explosive solutions are collected through a length of tubing for analysis. This was determined by analyzing the amount of explosive lost from solution per cm{sup 2} of tubing in solution. It was determined that tubing made of polyethylene, teflon, polypropylene, or KYNAR{reg_sign} is recommended for dilute trinitrotoluene (TNT) solution analyses. Tubing made of polypropylene, PHARMED{reg_sign}, KYNAR{reg_sign}, or polyethylene is recommended for analyses involving dilute explosive solutions of RDX. Tubing made from polyurethane, TYGON{reg_sign}, nylon, vinyl, gum rubber, or reinforced PVC are not recommended because they leach contaminants into solution that may interfere with HPLC analysis of explosive peaks.

  14. Working session 2: Tubing inspection

    SciTech Connect

    Guerra, J.; Tapping, R.L.

    1997-02-01

    This session was attended by delegates from 10 countries, and four papers were presented. A wide range of issues was tabled for discussion. Realizing that there was limited time available for more detailed discussion, three topics were chosen for the more detailed discussion: circumferential cracking, performance demonstration (to focus on POD and sizing), and limits of methods. Two other subsessions were organized: one dealt with some challenges related to the robustness of current inspection methods, especially with respect to leaving cracked tubes in service, and the other with developing a chart of current NDE technology with recommendations for future development. These three areas are summarized in turn, along with conclusions and/or recommendations. During the discussions there were four presentations. There were two (Canada, Japan) on eddy current probe developments, both of which addressed multiarray probes that would detect a range of flaws, one (Spain) on circumferential crack detection, and one (JRC, Petten) on the recent PISC III results.

  15. Atmospheres in a Test Tube

    NASA Astrophysics Data System (ADS)

    Claudi, R.; Erculiani, M. S.; Giro, E.; D'Alessandro, M.; Galletta, G.

    2013-09-01

    The "Atmosphere in a Test Tube" project is a laboratory experiment that will be able to reproduce condition of extreme environments by means of a simulator. These conditions span from those existing inside some parts of the human body to combinations of temperatures, pressures, irradiation and atmospheric gases present on other planets. In this latter case the experiments to be performed will be useful as preliminary tests for both simulation of atmosphere of exoplanets and Solar System planets and Astrobiology experiments that should be performed by planetary landers or by instruments to be launched in the next years. In particular at INAF Astronomical Observatory of Padova Laboratory we are approaching the characterization of extrasolar planet atmospheres taking advantage by innovative laboratory experiments with a particular focus on low mass Neptunes and Super earths and low mass M dwarfs primaries.

  16. Paramecium swimming in capillary tube

    NASA Astrophysics Data System (ADS)

    Jana, Saikat; Um, Soong Ho; Jung, Sunghwan

    2012-04-01

    Swimming organisms in their natural habitat need to navigate through a wide range of geometries and chemical environments. Interaction with boundaries in such situations is ubiquitous and can significantly modify the swimming characteristics of the organism when compared to ideal laboratory conditions. We study the different patterns of ciliary locomotion in glass capillaries of varying diameter and characterize the effect of the solid boundaries on the velocities of the organism. Experimental observations show that Paramecium executes helical trajectories that slowly transition to straight lines as the diameter of the capillary tubes decreases. We predict the swimming velocity in capillaries by modeling the system as a confined cylinder propagating longitudinal metachronal waves that create a finite pressure gradient. Comparing with experiments, we find that such pressure gradient considerations are necessary for modeling finite sized ciliary organisms in restrictive geometries.

  17. Data storage, image tube type

    NASA Technical Reports Server (NTRS)

    Lipoma, P. C. (Inventor)

    1973-01-01

    Method and apparatus for the storage of digital or analog electrical signals are provided by a memory storage system employing a conventional vidicon tube. At the beginning of an operating cycle, the vidicon is conditioned to accept electrical data input by exposing its photosensitive target to a short, high intensity light flash. A first electron beam scan of the photosensitive surface then sets up a charge pattern on the photosensitive target. A second electron beam scan of the photosensitive surface by an unmodulated electron beam then develops an output signal across an output resistor by using capacitive currents. The conditioning and scanning steps are operated repetitively at high speed using conventional television camera scan, sync, and power supply circuitry to provide a low cost data storage system.

  18. Is There an "F" in Your PAR? Understanding, Teaching and Doing Action Research

    ERIC Educational Resources Information Center

    Lorenzetti, Liza; Walsh, Christine Ann

    2014-01-01

    Participatory Action Research (PAR) is increasingly recognized within academic research and pedagogy. What are the benefits of including feminism within participatory action research and teaching? In responding to this question, we discuss the similarities and salient differences between PAR and feminist informed PAR (FPAR). There are eight themes…

  19. ParA resolvase catalyzes site-specific excision of DNA from the Arabidopsis genome

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The small serine resolvase ParA from bacterial plasmids RK2 and RP4 catalyzes the recombination of two identical 133 bp recombination sites known as MRS. Previously, we reported that ParA is active in the fission yeast Schizosaccharomyces pombe. In this work, the parA recombinase gene was placed un...

  20. The Role of Prostate Apoptosis Response-4 (Par-4) in Mycobacterium tuberculosis Infected Macrophages

    PubMed Central

    Han, Ji-Ye; Lim, Yun-Ji; Choi, Ji-Ae; Lee, Jung-hwan; Jo, Sung-Hee; Oh, Sung-Man; Song, Chang-Hwa

    2016-01-01

    Prostate apoptosis response-4 (Par-4) is a tumor suppressor protein that forms a complex with glucose-regulated protein 78 (GRP78) to induce apoptosis. Previously, we reported that ER stress-induced apoptosis is a critical host defense mechanism against Mycobacterium tuberculosis (Mtb). We sought to understand the role of Par-4 during ER stress-induced apoptosis in response to mycobacterial infection. Par-4 and GRP78 protein levels increased in response Mtb (strain: H37Ra) infection. Furthermore, Par-4 and GRP78 translocate to the surface of Mtb H37Ra-infected macrophages and induce apoptosis via caspase activation. NF-κB activation, Mtb-mediated ER stress, and Par-4 production were significantly diminished in macrophages with inhibited ROS production. To test Par-4 function during mycobacterial infection, we analyzed intracellular survival of Mtb H37Ra in macrophages with Par-4 overexpression or knockdown. Mtb H37Ra growth was significantly reduced in Par-4 overexpressing macrophages and increased in knockdown macrophages. We also observed increased Par-4, GRP78, and caspases activation in Bacillus Calmette-Guérin (BCG)-infected prostate cancer cells. Our data demonstrate that Par-4 is associated with ER stress-induced apoptosis resulting in reduced intracellular survival of mycobacteria. BCG treatment increases Par-4-dependent caspase activation in prostate cancer cells. These results suggest ER stress-induced Par-4 acts as an important defense mechanism against mycobacterial infection and regulates cancer. PMID:27552917

  1. Alternative 3' UTR selection controls PAR-5 homeostasis and cell polarity in C. elegans embryos.

    PubMed

    Mikl, Martin; Cowan, Carrie R

    2014-09-11

    Cell polarity in one-cell C. elegans embryos guides asymmetric cell division and cell-fate specification. Shortly after fertilization, embryos establish two antagonistic cortical domains of PAR proteins. Here, we find that the conserved polarity factor PAR-5 regulates PAR domain size in a dose-dependent manner. Using quantitative imaging and controlled genetic manipulation, we find that PAR-5 protein levels reflect the cumulative output of three mRNA isoforms with different translational efficiencies mediated by their 3' UTRs. 3' UTR selection is regulated, influencing PAR-5 protein abundance. Alternative splicing underlies the selection of par-5 3' UTR isoforms. 3' UTR splicing is enhanced by the SR protein kinase SPK-1, and accordingly, SPK-1 is required for wild-type PAR-5 levels and PAR domain size. Precise regulation of par-5 isoform selection is essential for polarization when the posterior PAR network is compromised. Together, strict control of PAR-5 protein levels and feedback from polarity to par-5 3' UTR selection confer robustness to embryo polarization. PMID:25199833

  2. Biased signalling and proteinase-activated receptors (PARs): targeting inflammatory disease.

    PubMed

    Hollenberg, M D; Mihara, K; Polley, D; Suen, J Y; Han, A; Fairlie, D P; Ramachandran, R

    2014-03-01

    Although it has been known since the 1960s that trypsin and chymotrypsin can mimic hormone action in tissues, it took until the 1990s to discover that serine proteinases can regulate cells by cleaving and activating a unique four-member family of GPCRs known as proteinase-activated receptors (PARs). PAR activation involves the proteolytic exposure of its N-terminal receptor sequence that folds back to function as a 'tethered' receptor-activating ligand (TL). A key N-terminal arginine in each of PARs 1 to 4 has been singled out as a target for cleavage by thrombin (PARs 1, 3 and 4), trypsin (PARs 2 and 4) or other proteases to unmask the TL that activates signalling via Gq , Gi or G12 /13 . Similarly, synthetic receptor-activating peptides, corresponding to the exposed 'TL sequences' (e.g. SFLLRN-, for PAR1 or SLIGRL- for PAR2) can, like proteinase activation, also drive signalling via Gq , Gi and G12 /13 , without requiring receptor cleavage. Recent data show, however, that distinct proteinase-revealed 'non-canonical' PAR tethered-ligand sequences and PAR-activating agonist and antagonist peptide analogues can induce 'biased' PAR signalling, for example, via G12 /13 -MAPKinase instead of Gq -calcium. This overview summarizes implications of this 'biased' signalling by PAR agonists and antagonists for the recognized roles the PARs play in inflammatory settings. PMID:24354792

  3. Independent Confirmation of the MODIS LAI/fPAR Algorithm

    NASA Astrophysics Data System (ADS)

    Ganapol, B. D.; Dungan, J. L.

    2001-12-01

    The Leaf Canopy Model (LCM)-2 is a nested model that combines leaf radiative transfer with a full canopy reflectance model through the phase function (Ganapol et al. 1999). The basic components of the model include inversion for a leaf scattering coefficient, construction of a representative absorption coefficient and the determination of canopy reflectance given leaf area index (LAI) values and information on canopy type and structure. It can also be used to calculate the fraction of absorbed photosynthetically active radiation (fPAR) for the canopy. It therefore serves as an independent means of confirming the results of the MOD15 algorithm (Knyazikhin et al. 1998) that produces LAI and fPAR fields from reflectance measured by the Moderate Resolution Imaging Spectrometer (MODIS). In LCM2, relatively simple first principles of radiative transfer are used whereas in the MOD15 algorithm, scene variability is accounted for by specifying distributions and a response surface in a table-lookup procedure. The distributions are generated by various radiative transfer models with a host of underlying assumptions. The attempt to compare results from these two models is a useful means of addressing the structural uncertainty in the Earth Observing System prediction problem. We compared LCM2 results with those from the MOD15 algorithm for fPAR calculation. 100 pixels for an EOS Core Validation Site where there were coincident reflectance, vegetation index, fPAR and LAI products were chosen. The 8-day 500 m reflectance product was spatially degraded to coincide with 8-day 1 km LAI and fPAR products and LAI and land cover products were used to parameterize LCM2. Most fPAR results agreed to within 10 percent, though a bias was observed. Poor agreement was seen with vegetation index products. Ganapol, B.D., L.F. Johnson, C.A. Hlavka, D.L. Peterson, and B. Bond, LCM2: A coupled leaf/canopy radiative transfer model, Remote Sensing of Environment, 70:153-166, 1999. Knyazikhin, Y., J

  4. ParCAT: A Parallel Climate Analysis Toolkit

    NASA Astrophysics Data System (ADS)

    Haugen, B.; Smith, B.; Steed, C.; Ricciuto, D. M.; Thornton, P. E.; Shipman, G.

    2012-12-01

    Climate science has employed increasingly complex models and simulations to analyze the past and predict the future of our climate. The size and dimensionality of climate simulation data has been growing with the complexity of the models. This growth in data is creating a widening gap between the data being produced and the tools necessary to analyze large, high dimensional data sets. With single run data sets increasing into 10's, 100's and even 1000's of gigabytes, parallel computing tools are becoming a necessity in order to analyze and compare climate simulation data. The Parallel Climate Analysis Toolkit (ParCAT) provides basic tools that efficiently use parallel computing techniques to narrow the gap between data set size and analysis tools. ParCAT was created as a collaborative effort between climate scientists and computer scientists in order to provide efficient parallel implementations of the computing tools that are of use to climate scientists. Some of the basic functionalities included in the toolkit are the ability to compute spatio-temporal means and variances, differences between two runs and histograms of the values in a data set. ParCAT is designed to facilitate the "heavy lifting" that is required for large, multidimensional data sets. The toolkit does not focus on performing the final visualizations and presentation of results but rather, reducing large data sets to smaller, more manageable summaries. The output from ParCAT is provided in commonly used file formats (NetCDF, CSV, ASCII) to allow for simple integration with other tools. The toolkit is currently implemented as a command line utility, but will likely also provide a C library for developers interested in tighter software integration. Elements of the toolkit are already being incorporated into projects such as UV-CDAT and CMDX. There is also an effort underway to implement portions of the CCSM Land Model Diagnostics package using ParCAT in conjunction with Python and gnuplot. Par

  5. Square tubing reduces cost of telescoping bridge crane hoist

    NASA Technical Reports Server (NTRS)

    Bernstein, G.; Graae, J.; Schraidt, J.

    1967-01-01

    Using standard square tubing in a telescoping arrangement reduces the cost of a bridge crane hoist. Because surface tolerances of square tubing need not be as accurate as the tubing used previously and because no spline is necessary, the square tubing is significantly less expensive than splined telescoping tubes.

  6. 21 CFR 876.5980 - Gastrointestinal tube and accessories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Gastrointestinal tube and accessories. 876.5980... tube and accessories. (a) Identification. A gastrointestinal tube and accessories is a device that..., gastrointestinal string and tubes to locate internal bleeding, double lumen tube for intestinal decompression...

  7. 21 CFR 876.5980 - Gastrointestinal tube and accessories.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Gastrointestinal tube and accessories. 876.5980... tube and accessories. (a) Identification. A gastrointestinal tube and accessories is a device that..., gastrointestinal string and tubes to locate internal bleeding, double lumen tube for intestinal decompression...

  8. 21 CFR 876.5980 - Gastrointestinal tube and accessories.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Gastrointestinal tube and accessories. 876.5980... tube and accessories. (a) Identification. A gastrointestinal tube and accessories is a device that..., gastrointestinal string and tubes to locate internal bleeding, double lumen tube for intestinal decompression...

  9. 21 CFR 876.5980 - Gastrointestinal tube and accessories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Gastrointestinal tube and accessories. 876.5980... tube and accessories. (a) Identification. A gastrointestinal tube and accessories is a device that..., gastrointestinal string and tubes to locate internal bleeding, double lumen tube for intestinal decompression...

  10. 21 CFR 876.5980 - Gastrointestinal tube and accessories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Gastrointestinal tube and accessories. 876.5980... tube and accessories. (a) Identification. A gastrointestinal tube and accessories is a device that..., gastrointestinal string and tubes to locate internal bleeding, double lumen tube for intestinal decompression...

  11. Building lab-scale x-ray tube based irradiators

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The construction of economical x-ray tube based irradiators in a variety of configurations is described using 1000 Watt x-ray tubes. Single tube, double tube, and four tube designs are described, as well as various cabinet construction techniques. Relatively high dose rates were achieved for small s...

  12. Ultrasonic Inspection Of Welds On Tube Fittings

    NASA Technical Reports Server (NTRS)

    Ray, Arjun N.; Nummelin, John L.

    1996-01-01

    Scanning ultrasonic apparatus designed for use in nondestructive inspection of electron-beam welds between heat-exchanger tube and end fittings. Includes ultrasonic probe, scanning mechanism, ultrasonic-signal-generating and -processing circuits, and computers. Not necessary to immerse any part of apparatus or tube/fitting assembly in water during inspection. Output ultrasonic-test signals displayed on computer to reveal defects.

  13. Metal hydrides studied in gas discharge tube

    NASA Astrophysics Data System (ADS)

    Bozhinova, I.; Kolev, S.; Popov, Tsv.; Pashov, A.; Dimitrova, M.

    2016-05-01

    A novel construction of gas discharge tube has been tested for production of high densities of metal hydrydes. Its performance turned out to be comparable with the existing sources of the same type and even better. First results of the tests on NiH are reported and critically analysed. Plans for future modifiaction of the construction and application of the tube are discussed.

  14. Numerical study of an underground heat tube

    SciTech Connect

    Sulaiman, F.

    1989-01-01

    The energy consumption of the air-to-air heat pump can be reduced, especially in winter, by using the soil as a heat source. A system of buried tube through which air is passed, has great potential in supplying higher temperature air than the ambient air, to the outside heat exchanger of the heat pump. Heat transfer from the soil to the tube, including the possibility of formation of ice lenses around the tube, was investigated over a period of time in a cold season. Models of ice formation were developed in two types of tube, the circular tube and the square tube. Latent heat released due to the formation of ice were included in the models. Computer simulation utilizing finite difference equations were developed, using the explicit method, where forward differences were used in time and central differences were used in space. The numerical results show the effects of increasing the moisture content of the soil, increasing the air flow rate in the tube, and the release of latent heat when soil freezes. The formation of ice around the tube played a significant role in achieving a stabilized output air temperature at a short time.

  15. Distortion Of Pressure Signals In Pneumatic Tubes

    NASA Technical Reports Server (NTRS)

    Whitmore, Stephen A.; Gilyard, Glenn B.; Curry, Robert; Lindsey, William

    1993-01-01

    NASA technical memorandum describes experimental investigation of distorting effects of propagation of pressure signals along narrow pneumatic tubes from pressure-sensing orifices on surfaces of models or aircraft to pressure sensors distant from orifices. Pressure signals distorted principally by frictional damping along walls of tubes and by reflections at orifice and sensor ends.

  16. Substantially Oxygen-Free Contact Tube

    NASA Technical Reports Server (NTRS)

    Pike, James F. (Inventor)

    1991-01-01

    A device for arc welding is provided in which a continuously-fed electrode wire is in electrical contact with a contact tube. The contact tube is improved by using a substantially oxygen-free conductive alloy in order to reduce the amount of electrical erosion.

  17. Glass tubes for protecting solar cells

    NASA Technical Reports Server (NTRS)

    Shelpuk, B.

    1978-01-01

    Protecting solar cells against environmental effects is accomplished by putting them inside glass tubes instead of hermetically sealing them between pairs of flat glass sheets. If cells are coupled with storage battery integrated into tube, freestanding power source could be built.

  18. Making Glass-Fiber-Reinforced Coolant Tubes

    NASA Technical Reports Server (NTRS)

    Curtin, F.

    1985-01-01

    New use found for heat-shrinkable sleeves. Smooth, noncontaminating channels for transporting cooling water in Space Shuttle Extravehicularmobility unit made of fiberglass tubing with aid of heat-shrinkable sleeves. Previously, glass fibers from inner walls of tubes contaminate water.

  19. Identification of Aircraft Tubing by Rockwell Test

    NASA Technical Reports Server (NTRS)

    Knerr, Horace C.

    1930-01-01

    Seamless steel tubing is today the principal material of construction for aircraft. The commercial grade of tubing containing about 0.10 to 0.20% carbon at first used is being superseded by two grades which are approved by the army and navy, and which are also becoming standard for commercial airplanes.

  20. Sampling Artifacts from Conductive Silicone Tubing

    SciTech Connect

    Timko, Michael T.; Yu, Zhenhong; Kroll, Jesse; Jayne, John T.; Worsnop, Douglas R.; Miake-Lye, Richard C.; Onasch, Timothy B.; Liscinsky, David; Kirchstetter, Thomas W.; Destaillats, Hugo; Holder, Amara L.; Smith, Jared D.; Wilson, Kevin R.

    2009-05-15

    We report evidence that carbon impregnated conductive silicone tubing used in aerosol sampling systems can introduce two types of experimental artifacts: 1) silicon tubing dynamically absorbs carbon dioxide gas, requiring greater than 5 minutes to reach equilibrium and 2) silicone tubing emits organic contaminants containing siloxane that adsorb onto particles traveling through it and onto downstream quartz fiber filters. The consequence can be substantial for engine exhaust measurements as both artifacts directly impact calculations of particulate mass-based emission indices. The emission of contaminants from the silicone tubing can result in overestimation of organic particle mass concentrations based on real-time aerosol mass spectrometry and the off-line thermal analysis of quartz filters. The adsorption of siloxane contaminants can affect the surface properties of aerosol particles; we observed a marked reduction in the water-affinity of soot particles passed through conductive silicone tubing. These combined observations suggest that the silicone tubing artifacts may have wide consequence for the aerosol community and should, therefore, be used with caution. Gentle heating, physical and chemical properties of the particle carriers, exposure to solvents, and tubing age may influence siloxane uptake. The amount of contamination is expected to increase as the tubing surface area increases and as the particle surface area increases. The effect is observed at ambient temperature and enhanced by mild heating (<100 oC). Further evaluation is warranted.

  1. Shrinking plastic tubing and nonstandard diameters

    NASA Technical Reports Server (NTRS)

    Ruiz, W. V.; Thatcher, C. S.

    1980-01-01

    Process allows larger-than-normal postshrink diameters without splitting. Tetrafluoroethylene tubing on mandrel is supported within hot steel pipe by several small diameter coil sections. Rising temperature of mandrel is measured via thermocouple so assembly can be removed without overshrinking (and splitting) of tubing.

  2. 21 CFR 874.3880 - Tympanostomy tube.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3880 Tympanostomy tube. (a) Identification. A tympanostomy tube is a device that is intended to be implanted for ventilation or drainage of...

  3. 21 CFR 874.3880 - Tympanostomy tube.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3880 Tympanostomy tube. (a) Identification. A tympanostomy tube is a device that is intended to be implanted for ventilation or drainage of...

  4. Plastic tubing protects flexible copper hose

    NASA Technical Reports Server (NTRS)

    Mellgren, B. E.

    1966-01-01

    Flexible copper purge and coolant hoses is covered with a high-temperature shrinkable plastic for protection against severe vibration during rocket engine tests. This type of tubing is being used on all flexible water tubes used in F-1 engine tests.

  5. Teaching Shakespeare with YouTube

    ERIC Educational Resources Information Center

    Desmet, Christy

    2009-01-01

    YouTube, the video sharing website that allows viewers to upload video content ranging from cute dog tricks to rare rock videos, also supports a lively community devoted to the performance of Shakespeare and Shakespearean adaptations. YouTube is also a popular site for student producers of Shakespeare performances, parodies, and other artistic…

  6. Places to Go: YouTube

    ERIC Educational Resources Information Center

    Downes, Stephen

    2008-01-01

    Founded in 2005 by three former PayPal employees, YouTube has revolutionized the Internet, marking a change from the static Internet to the dynamic Internet. In this edition of Places to Go, Stephen Downes discusses how the rise of a ubiquitous media format--Flash video--has made YouTube's success possible and argues that Flash video has important…

  7. Test fittings for dimensionally critical tubes

    NASA Technical Reports Server (NTRS)

    Hagler, R.

    1980-01-01

    Method using lightweight fitting protects tubes and tube stubs during testing and through to final welding. Fitting does not interfere with final welding or brazing like temporary test fittings, and is not heavy like machined-on integral fittings with face-seal 0-rings. Fitting approach is adaptable to many types of components, including valves, transducers, and filters.

  8. Microphone Detects Boiler-Tube Leaks

    NASA Technical Reports Server (NTRS)

    Parthasarathy, S. P.

    1985-01-01

    Unit simple, sensitive, rugged, and reliable. Diaphragmless microphone detects leaks from small boiler tubes. Porous plug retains carbon granules in tube while allowing pressure changes to penetrate to granules. Has greater life expectancy than previous controllers and used in variety of hot corrosive atmospheres.

  9. Coke from small-diameter tubes analyzed

    SciTech Connect

    Albright, L.F.

    1988-08-29

    The mechanism for coke deposit formation and the nature of the coke itself can vary with the design of the ethylene furnace tube bank. In this article, coke deposits from furnaces with small-diameter pyrolysis tubes are examined. The samples were taken from four furnaces of identical design (Plant B). As in both the first and second installments of the series, the coke deposits were examined using a scanning electron microscope (SEM) and an energy dispersive X-ray analyzer (EDAX). The deposits from the small-diameter tubes are compared with the coke deposits from the furnace discussed in earlier articles. Analysis of the coke in both sets of samples are then used to offer recommendations for improved decoking procedures, operating procedures, better feed selection, and better selection of the metallurgy used in furnace tubes, to extend the operating time of the furnace tubes by reducing the amount and type of coke build up.

  10. Tube Visualization and Properties from Isoconfigurational Averaging

    NASA Astrophysics Data System (ADS)

    Qin, Jian; Bisbee, Windsor; Milner, Scott

    2012-02-01

    We introduce a simulation method to visualize the confining tube in polymer melts and measure its properties. We studied bead-spring ring polymers, which conveniently suppresses constraint release and contour length fluctuations. We allow molecules to cross and reach topologically equilibrated states by invoking various molecular rebridging moves in Monte Carlo simulations. To reveal the confining tube, we start with a well equilibrated configuration, turn off rebridging moves, and run molecular dynamics simulation multiple times, each with different initial velocities. The resulting set of ``movies'' of molecular trajectories defines an isoconfigurational ensemble, with the bead positions at different times and in different ``movies'' giving rise to a cloud. The cloud shows the shape, range and strength of the tube confinement, which enables us to study the statistical properties of tube. Using this approach, we studied the effects of free surface, and found that the tube diameter near the surface is greater than the bulk value by about 25%.

  11. RF Liquid Measurement Of Capillary Tubes

    NASA Astrophysics Data System (ADS)

    Poudyal, Bashudev; Mazzeo, Brian; Warnick, Karl

    2009-10-01

    Electromagnetic measurements of capillary tubes containing liquids can reveal solution properties for industrial, biological, and chemical processes. An analytical model was created for a perpendicular arrangement of SMA cables and a capillary tube. Numerical simulations in Ansoft High Frequency Structural Simulator were performed on the simple arrangement. The transmission parameters of the capillary tube were simulated between two lumped ports over a frequency range from 1 GHz to 20 GHz. Sensitivity of the transmission parameters to solution conditions were calculated for DI water and other variations of conductivity and permittivity. Experiments were performed on a capillary tube in a perpendicular arrangement using an HP 8720B Network Analyzer. The transmission parameters were measured and the resulting data was compared with the simulations. This measurement method can be adapted to different tube and solution conditions.

  12. Ultra-fast framing camera tube

    DOEpatents

    Kalibjian, Ralph

    1981-01-01

    An electronic framing camera tube features focal plane image dissection and synchronized restoration of the dissected electron line images to form two-dimensional framed images. Ultra-fast framing is performed by first streaking a two-dimensional electron image across a narrow slit, thereby dissecting the two-dimensional electron image into sequential electron line images. The dissected electron line images are then restored into a framed image by a restorer deflector operated synchronously with the dissector deflector. The number of framed images on the tube's viewing screen is equal to the number of dissecting slits in the tube. The distinguishing features of this ultra-fast framing camera tube are the focal plane dissecting slits, and the synchronously-operated restorer deflector which restores the dissected electron line images into a two-dimensional framed image. The framing camera tube can produce image frames having high spatial resolution of optical events in the sub-100 picosecond range.

  13. Cross ambiguity functions on the MasPar MP-2

    SciTech Connect

    Carlson, D.A.; Pryor, D.V.; Frock, C.K.

    1995-12-01

    In a signal processing environment, cross ambiguity functions are often used to detect when one signal is a time and/or frequency shift of another. They consist of multiple cross-correlations, which can be computed efficiently using complex valued FFTs. This paper discusses the implementation of cross ambiguity functions on the MasPar MP-2, a SIMD processor array. Two different implementations are developed. The first computes each cross ambiguity function serially, using FFT code that parallelizes across the complete set of processors. The second uses the MasPar IORAM to realign the data so that the cross ambiguity functions can be computed in parallel. In this case, multiple FFTs are executed in parallel on subsets of the processors, which lowers the overall amount of communication required.

  14. Design, construction, and wire calibration of PAR BPM striplines

    NASA Astrophysics Data System (ADS)

    Sellyey, W.; Barr, D.; Erwin, L.

    1995-05-01

    The Positron Accumulator Ring (PAR) is part of the APS injection system. It received 24 30-ns FWHM bursts of 450-meV positrons, and compresses them into 6-nC, 290-ps rms bunches. Striplines were selected as beam position monitors (BPMs) to assure that good position sensitivity is achieved. This paper will describe the design, construction, and wire calibration of the 16 PAR BPMs. It will be demonstrated that all relevant stripline parameters can be determined by solving the two-dimensional LaPlace equation. This was done numerically using the electrostatic part of the PE2D computer program. The construction of the units will be briefly discussed. Wire calibration data on one of the final units will be compared with theory at four frequencies.

  15. Characterization of oxides on Bruce A NGS liner tubes and steam generator tubes

    SciTech Connect

    Miller, D.G.; Burrill, K.A.

    1998-12-31

    Oxide deposits on end-fitting liner tubes and steam generator tubes from the Bruce A Nuclear Generating Station (NGS) were characterized in advance of the decontamination of the heat transport system (HTS) of Bruce Unit 2. Oxide loadings, and Co-60 surface activities and specific activities were determined for the oxides on inlet and outlet end-fitting liner tubes from Bruce Unit l, Bruce Unit 2 and Bruce Unit 4. Oxides on the inner surfaces of steam generator tubes from Bruce NGS Units 1 and 2 were also characterized. The consistency in the deposit characteristics on the inlet liner tubes and steam generator tubes from Bruce A, along with the absence of magnetite on the outlet liner tubes has led to the development of a model for iron transport in the HTS of pressurized heavy water reactors (PHWRs). The activity transport/fouling mechanism involves flow-accelerated corrosion of the outlet feeder pipes, followed by deposition of iron in the steam generators, along the inlet feeder pipes, on the inlet end fittings, on the inlet fuel bundles and on the inlet region of the pressure tube. The results of loop experiments using decontamination solutions indicated that the oxide was rapidly removed from inlet liner tubes. However, removal of the Cr-rich oxide from the outlet liner tubes was less efficient, requiring the Alkaline Permangante (AP) oxidizing pre-treatment that is typically used in light water reactors (LWRs). The steam generator tubes were effectively decontaminated.

  16. [Isolated rupture of the left main-stem bronchus during intubation with a Carlens tube].

    PubMed

    Ortolo, B; Sainte-Rose, G; Brémant, S; Lecoeur, J; Rouge, M

    1988-01-01

    A case is reported of bronchial rupture due to a Carlens double-lumen tube. A 73 year old male patient was to undergo a double right lower and middle lobectomy for carcinoma. All went well and as expected until 20 min after the start of left-sided unilateral ventilation by way of the double-lumen tube. A sudden increase in the inspiratory pressures led to the discovery, first, of a leak around the cuff, and then, air bubbles in the mediastinum. Surgical exploration showed up the 4 cm long rupture in the pars membrana of the left main bronchus through which the cuff was herniating. The patient was reintubated and the rupture surgically repaired. The right upper lobe had not been ventilated for 45 min and there were signs of micro-atelectasia. The immediate postoperative course was rather stormy, with severe cardiac failure, recurring right upper lobe atelectasia and bilateral pulmonary infection. The patient was only definitely weaned from the respirator 40 days after the surgical incident. Although such complications with double-lumen tubes are rare, they must be recognized and surgically repaired very rapidly. A few simple rules to prevent these complications are discussed. PMID:3207231

  17. Macroinvertebrates of Par Pond and Pond B: Final report, January 1984-June 1985

    SciTech Connect

    Kondratieff, B.C.; Chimney, M.J.; Painter, W.B.

    1985-08-01

    This document reports on the Par Pond and Pond B macroinvertebrate sampling program from January 1984 through June 1985. It includes data on quantitative and qualitative benthic sampling, quantitative meroplankton sampling and quarterly diel sample. The basic objectives were to: (1) characterize the benthic and meroplankton macroinvertebrate communities of Par Pond and Pond B, with respect to taxonomic composition and diversity, density and relative abundance of functional feeding groups; (2) assess the impact of thermal discharges on the macroinvertebrate community of Par Pond; (3) assess the impact and significance of entrainment losses of macroinvertebrate meroplankton from Par Pond; and (4) compare Par Pond macroninvertebrate communities with those in Pond B.

  18. The Pars Interarticularis Stress Reaction, Spondylolysis, and Spondylolisthesis Progression

    PubMed Central

    Motley, Gina; Nyland, John; Jacobs, Jake; Caborn, David N. M.

    1998-01-01

    Objective: To review the classification, etiology, clinical and radiologic evaluation, and management of the pars interarticularis stress reaction, spondylolysis, and spondylolisthesis progression. Data Sources: Grateful Med was searched from 1980 to 1998 using the terms “spondylolysis,” “spondylolisthesis,” “female athlete” “spondylogenic,” and “pars interarticularis.” Data Synthesis: The progression from pars interarticularis stress reaction through spondylolysis to spondylolisthesis is common in adolescent athletes, and, because of hormonal influences and cheerleading and gymnastic maneuvers, females are particularly at risk. Proper diagnosis and management include a thorough evaluation, radiographs (possibly with technetium bone scan or single-photon emission computed tomography), activity modification, dietary counseling, a therapeutic exercise program focusing on proper trunk and hip muscle strength and extensibility balances, and education regarding proper back postures, positioning, lifting mechanics, and jump landings. Conclusions/Recommendations: The athletic trainer plays an integral part in managing this injury progression, particularly with identifying at-risk individuals and intervening appropriately. ImagesFigure 4. PMID:16558534

  19. OXIDE DISPERSION-STRENGTHENED HEAT EXCHANGER TUBING

    SciTech Connect

    Harper, Mark A.

    2001-11-06

    Oxide dispersion strengthened (ODS) alloys (e.g. the INCOLOY{reg_sign} MA956 alloy) are known for their excellent high temperature properties and are prime candidate materials for the construction of very high temperature heat exchangers that will be used in Vision 21 power plants. The main limitation of these materials is their poor weldability. Commercially available ODS tubing also tends to exhibit relatively poor circumferential creep strength due to current processing practices resulting in a fine grain size in the transverse direction. Thus far, these two characteristics of the ODS tubing have restricted its use to mostly non-pressure containing applications. The objectives of this program are to develop: (a) an MA956 tube with sufficient circumferential creep strength for long term use as heat exchanger tubing for very high temperatures; (b) a welding technique(s) for producing adequate joints between an MA956 tube and an MA956 tube, and an MA956 tube and an INCONEL 601 tube; (c) the bending strain limits, below which recrystallization will not occur in a MA956 tube during normal operation; and (d) the high temperature corrosion limits for the MA956 alloy with respect to working-fluid side and fireside environments. Also, this program seeks to generate data for use by heat exchanger designers and the ASME Boiler and Pressure Vessel Code, and perform an analysis of the mechanical property, tube bending, and corrosion data in order to determine the implications on the design of a very high temperature heat exchanger (T>1093 C/2000 F). After one year, work is currently being conducted on increasing the circumferential strength of a MA956 tube, developing joining techniques for this material, determining the tube bending strain limits, and establishing the high temperature corrosion parameters for the MA956 alloy in environments expected to be present in Vision 21 power plants. Work in these areas will is continuing into the next fiscal year, with success

  20. Phase detonated shock tube (PFST)

    SciTech Connect

    Zerwekh, W.D.; Marsh, S.P.; Tan, Tai-Ho

    1993-07-01

    The simple, cylindrically imploding and axially driven fast shock tube (FST) has been a basic component in the high velocity penetrator (HVP) program. It is a powerful device capable of delivering a directed and very high pressure output that has been successfully employed to drive hypervelocity projectiles. The FST is configured from a hollow, high-explosive (HE) cylinder, a low-density Styrofoam core, and a one-point initiator at one end. A Mach stem is formed in the core as the forward-propagating, HE detonation wave intersects the reflected radial wave. This simple FST has been found to be a powerful pressure multiplier. Up to 1-Mbar output pressure can be obtained from this device. Further increase in the output pressure can be achieved by increasing the HE detonation velocity. The FST has been fine tuned to drive a thin plate to very high velocity under an impulse per unit area of about 1 Mbar{mu}s/cm{sup 2}. A 1.5-mm-thick stainless steel disk has been accelerated intact to 0.8 cm/{mu}s under a loading pressure rate of several Mbar/{mu}s. By making the plate curvature slightly convex at the loading side the authors have successfully accelerated it to almost 1.0 cm/{mu}s. The incorporation of a barrel at the end of the FST has been found to be important as confinement of the propellant gas by the barrel tends to accelerate the projectile to higher velocity. The desire to accelerate the plate above 1.0 cm/{mu}s provided the impetus to develop a more advanced fast shock tube to deliver a much higher output pressure. This report describes the investigation of a relatively simple air-lens phase-detonation system (PFST) with fifty percent higher phase-detonation velocity and a modest 2 Mbar output. Code calculations have shown that this PFST acceleration of a plate to about 1.2 cm/{mu}s can be achieved. The performance of these PFSTs has been evaluated and the details are discussed.

  1. Phase detonated shock tube (PFST)

    SciTech Connect

    Zerwekh, W.D.; Marsh, S.P.; Tan, Tai-Ho.

    1993-01-01

    The simple, cylindrically imploding and axially driven fast shock tube (FST) has been a basic component in the high velocity penetrator (HVP) program. It is a powerful device capable of delivering a directed and very high pressure output that has been successfully employed to drive hypervelocity projectiles. The FST is configured from a hollow, high-explosive (HE) cylinder, a low-density Styrofoam core, and a one-point initiator at one end. A Mach stem is formed in the core as the forward-propagating, HE detonation wave intersects the reflected radial wave. This simple FST has been found to be a powerful pressure multiplier. Up to 1-Mbar output pressure can be obtained from this device. Further increase in the output pressure can be achieved by increasing the HE detonation velocity. The FST has been fine tuned to drive a thin plate to very high velocity under an impulse per unit area of about 1 Mbar[mu]s/cm[sup 2]. A 1.5-mm-thick stainless steel disk has been accelerated intact to 0.8 cm/[mu]s under a loading pressure rate of several Mbar/[mu]s. By making the plate curvature slightly convex at the loading side the authors have successfully accelerated it to almost 1.0 cm/[mu]s. The incorporation of a barrel at the end of the FST has been found to be important as confinement of the propellant gas by the barrel tends to accelerate the projectile to higher velocity. The desire to accelerate the plate above 1.0 cm/[mu]s provided the impetus to develop a more advanced fast shock tube to deliver a much higher output pressure. This report describes the investigation of a relatively simple air-lens phase-detonation system (PFST) with fifty percent higher phase-detonation velocity and a modest 2 Mbar output. Code calculations have shown that this PFST acceleration of a plate to about 1.2 cm/[mu]s can be achieved. The performance of these PFSTs has been evaluated and the details are discussed.

  2. Ear tube surgery - what to ask your doctor

    MedlinePlus

    ... this page: //medlineplus.gov/ency/patientinstructions/000220.htm Ear tube surgery - what to ask your doctor To ... enable JavaScript. Your child is being evaluated for ear tube insertion. This is the placement of tubes ...

  3. 30 CFR 250.517 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Gas Well-Completion Operations § 250.517 Tubing and wellhead equipment. (a) No tubing string shall be placed in service or continue to be used unless such tubing string has the necessary strength...

  4. 30 CFR 250.1626 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Tubing and wellhead equipment. (a) No tubing string shall be placed into service or continue to be used unless such tubing string has the necessary strength and pressure integrity and is otherwise suitable...

  5. 30 CFR 250.1626 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Operations § 250.1626 Tubing and wellhead equipment. (a) No tubing string shall be placed into service or continue to be used unless such tubing string has the necessary strength and pressure integrity and...

  6. 30 CFR 250.518 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Operations § 250.518 Tubing and wellhead equipment. (a) No tubing string shall be placed in service or continue to be used unless such tubing string has the necessary strength and pressure integrity and...

  7. 30 CFR 250.1626 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Tubing and wellhead equipment. (a) No tubing string shall be placed into service or continue to be used unless such tubing string has the necessary strength and pressure integrity and is otherwise suitable...

  8. 30 CFR 250.517 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Tubing and wellhead equipment. (a) No tubing string shall be placed in service or continue to be used unless such tubing string has the necessary strength and pressure integrity and is otherwise suitable...

  9. 30 CFR 250.1626 - Tubing and wellhead equipment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Tubing and wellhead equipment. (a) No tubing string shall be placed into service or continue to be used unless such tubing string has the necessary strength and pressure integrity and is otherwise suitable...

  10. ParB Partition Proteins: Complex Formation and Spreading at Bacterial and Plasmid Centromeres

    PubMed Central

    Funnell, Barbara E.

    2016-01-01

    In bacteria, active partition systems contribute to the faithful segregation of both chromosomes and low-copy-number plasmids. Each system depends on a site-specific DNA binding protein to recognize and assemble a partition complex at a centromere-like site, commonly called parS. Many plasmid, and all chromosomal centromere-binding proteins are dimeric helix-turn-helix DNA binding proteins, which are commonly named ParB. Although the overall sequence conservation among ParBs is not high, the proteins share similar domain and functional organization, and they assemble into similar higher-order complexes. In vivo, ParBs “spread,” that is, DNA binding extends away from the parS site into the surrounding non-specific DNA, a feature that reflects higher-order complex assembly. ParBs bridge and pair DNA at parS and non-specific DNA sites. ParB dimers interact with each other via flexible conformations of an N-terminal region. This review will focus on the properties of the HTH centromere-binding protein, in light of recent experimental evidence and models that are adding to our understanding of how these proteins assemble into large and dynamic partition complexes at and around their specific DNA sites. PMID:27622187

  11. ParB Partition Proteins: Complex Formation and Spreading at Bacterial and Plasmid Centromeres

    PubMed Central

    Funnell, Barbara E.

    2016-01-01

    In bacteria, active partition systems contribute to the faithful segregation of both chromosomes and low-copy-number plasmids. Each system depends on a site-specific DNA binding protein to recognize and assemble a partition complex at a centromere-like site, commonly called parS. Many plasmid, and all chromosomal centromere-binding proteins are dimeric helix-turn-helix DNA binding proteins, which are commonly named ParB. Although the overall sequence conservation among ParBs is not high, the proteins share similar domain and functional organization, and they assemble into similar higher-order complexes. In vivo, ParBs “spread,” that is, DNA binding extends away from the parS site into the surrounding non-specific DNA, a feature that reflects higher-order complex assembly. ParBs bridge and pair DNA at parS and non-specific DNA sites. ParB dimers interact with each other via flexible conformations of an N-terminal region. This review will focus on the properties of the HTH centromere-binding protein, in light of recent experimental evidence and models that are adding to our understanding of how these proteins assemble into large and dynamic partition complexes at and around their specific DNA sites.

  12. Proteinase-Activated Receptor 1 (PAR1) Regulates Leukemic Stem Cell Functions

    PubMed Central

    Bäumer, Nicole; Krause, Annika; Köhler, Gabriele; Lettermann, Stephanie; Evers, Georg; Hascher, Antje; Bäumer, Sebastian; Berdel, Wolfgang E.

    2014-01-01

    External signals that are mediated by specific receptors determine stem cell fate. The thrombin receptor PAR1 plays an important role in haemostasis, thrombosis and vascular biology, but also in tumor biology and angiogenesis. Its expression and function in hematopoietic stem cells is largely unknown. Here, we analyzed expression and function of PAR1 in primary hematopoietic cells and their leukemic counterparts. AML patients' blast cells expressed much lower levels of PAR1 mRNA and protein than CD34+ progenitor cells. Constitutive Par1-deficiency in adult mice did not affect engraftment or stem cell potential of hematopoietic cells. To model an AML with Par1-deficiency, we retrovirally introduced the oncogene MLL-AF9 in wild type and Par1−/− hematopoietic progenitor cells. Par1-deficiency did not alter initial leukemia development. However, the loss of Par1 enhanced leukemic stem cell function in vitro and in vivo. Re-expression of PAR1 in Par1−/− leukemic stem cells delayed leukemogenesis in vivo. These data indicate that Par1 contributes to leukemic stem cell maintenance. PMID:24740120

  13. ParB Partition Proteins: Complex Formation and Spreading at Bacterial and Plasmid Centromeres.

    PubMed

    Funnell, Barbara E

    2016-01-01

    In bacteria, active partition systems contribute to the faithful segregation of both chromosomes and low-copy-number plasmids. Each system depends on a site-specific DNA binding protein to recognize and assemble a partition complex at a centromere-like site, commonly called parS. Many plasmid, and all chromosomal centromere-binding proteins are dimeric helix-turn-helix DNA binding proteins, which are commonly named ParB. Although the overall sequence conservation among ParBs is not high, the proteins share similar domain and functional organization, and they assemble into similar higher-order complexes. In vivo, ParBs "spread," that is, DNA binding extends away from the parS site into the surrounding non-specific DNA, a feature that reflects higher-order complex assembly. ParBs bridge and pair DNA at parS and non-specific DNA sites. ParB dimers interact with each other via flexible conformations of an N-terminal region. This review will focus on the properties of the HTH centromere-binding protein, in light of recent experimental evidence and models that are adding to our understanding of how these proteins assemble into large and dynamic partition complexes at and around their specific DNA sites. PMID:27622187

  14. Dynamic Filament Formation by a Divergent Bacterial Actin-Like ParM Protein

    PubMed Central

    Brzoska, Anthony J.; Jensen, Slade O.; Barton, Deborah A.; Davies, Danielle S.; Overall, Robyn L.; Skurray, Ronald A.; Firth, Neville

    2016-01-01

    Actin-like proteins (Alps) are a diverse family of proteins whose genes are abundant in the chromosomes and mobile genetic elements of many bacteria. The low-copy-number staphylococcal multiresistance plasmid pSK41 encodes ParM, an Alp involved in efficient plasmid partitioning. pSK41 ParM has previously been shown to form filaments in vitro that are structurally dissimilar to those formed by other bacterial Alps. The mechanistic implications of these differences are not known. In order to gain insights into the properties and behavior of the pSK41 ParM Alp in vivo, we reconstituted the parMRC system in the ectopic rod-shaped host, E. coli, which is larger and more genetically amenable than the native host, Staphylococcus aureus. Fluorescence microscopy showed a functional fusion protein, ParM-YFP, formed straight filaments in vivo when expressed in isolation. Strikingly, however, in the presence of ParR and parC, ParM-YFP adopted a dramatically different structure, instead forming axial curved filaments. Time-lapse imaging and selective photobleaching experiments revealed that, in the presence of all components of the parMRC system, ParM-YFP filaments were dynamic in nature. Finally, molecular dissection of the parMRC operon revealed that all components of the system are essential for the generation of dynamic filaments. PMID:27310470

  15. The physical association of the P2Y12 receptor with PAR4 regulates arrestin-mediated Akt activation.

    PubMed

    Khan, Aasma; Li, Dongjun; Ibrahim, Salam; Smyth, Emer; Woulfe, Donna S

    2014-07-01

    It is now well accepted that protease activated receptor (PAR) 1 and PAR4 have differential roles in platelet activation. PAR4, a low-affinity thrombin receptor in human platelets, participates in sustained platelet activation in a P2Y12-dependent manner; however, the mechanisms are not defined. Our previous studies demonstrated that thrombin induces the association of PAR4 with P2Y12, together with arrestin recruitment to the complex. Here we show that PAR4 and P2Y12 directly interact to coregulate Akt signaling after PAR4 activation. We observed direct and specific interaction of P2Y12 with PAR4 but not PAR1 by bioluminescent resonance energy transfer when the receptors were coexpressed in human embryonic kidney 293T cells. PAR4-P2Y12 dimerization was promoted by PAR4-AP and inhibited by P2Y12 antagonist. By using sequence comparison of the transmembrane domains of PAR1 and PAR4, we designed a mutant form of PAR4, "PAR4SFT," by replacing LGL194-196 at the base of transmembrane domain 4 with the corresponding aligned PAR1 residues SFT 220-222. PAR4SFT supported only 8.74% of PAR4-P2Y12 interaction, abolishing P2Y12-dependent arrestin recruitment to PAR4 and Akt activation. Nonetheless, PAR4SFT still supported homodimerization with PAR4. PAR4SFT failed to induce a calcium flux when expressed independently; however, coexpression of increasing concentrations of PAR4SFT, together with PAR4 potentiated PAR4-mediated calcium flux, suggested that PAR4 act as homodimers to signal to Gq-coupled calcium responses. In conclusion, PAR4 LGL (194-196) governs agonist-dependent association of PAR4 with P2Y12 and contributes to Gq-coupled calcium responses. PAR4-P2Y12 association supports arrestin-mediated sustained signaling to Akt. Hence, PAR4-P2Y12 dimerization is likely to be important for the PAR4-P2Y12 dependent stabilization of platelet thrombi.

  16. The physical association of the P2Y12 receptor with PAR4 regulates arrestin-mediated Akt activation.

    PubMed

    Khan, Aasma; Li, Dongjun; Ibrahim, Salam; Smyth, Emer; Woulfe, Donna S

    2014-07-01

    It is now well accepted that protease activated receptor (PAR) 1 and PAR4 have differential roles in platelet activation. PAR4, a low-affinity thrombin receptor in human platelets, participates in sustained platelet activation in a P2Y12-dependent manner; however, the mechanisms are not defined. Our previous studies demonstrated that thrombin induces the association of PAR4 with P2Y12, together with arrestin recruitment to the complex. Here we show that PAR4 and P2Y12 directly interact to coregulate Akt signaling after PAR4 activation. We observed direct and specific interaction of P2Y12 with PAR4 but not PAR1 by bioluminescent resonance energy transfer when the receptors were coexpressed in human embryonic kidney 293T cells. PAR4-P2Y12 dimerization was promoted by PAR4-AP and inhibited by P2Y12 antagonist. By using sequence comparison of the transmembrane domains of PAR1 and PAR4, we designed a mutant form of PAR4, "PAR4SFT," by replacing LGL194-196 at the base of transmembrane domain 4 with the corresponding aligned PAR1 residues SFT 220-222. PAR4SFT supported only 8.74% of PAR4-P2Y12 interaction, abolishing P2Y12-dependent arrestin recruitment to PAR4 and Akt activation. Nonetheless, PAR4SFT still supported homodimerization with PAR4. PAR4SFT failed to induce a calcium flux when expressed independently; however, coexpression of increasing concentrations of PAR4SFT, together with PAR4 potentiated PAR4-mediated calcium flux, suggested that PAR4 act as homodimers to signal to Gq-coupled calcium responses. In conclusion, PAR4 LGL (194-196) governs agonist-dependent association of PAR4 with P2Y12 and contributes to Gq-coupled calcium responses. PAR4-P2Y12 association supports arrestin-mediated sustained signaling to Akt. Hence, PAR4-P2Y12 dimerization is likely to be important for the PAR4-P2Y12 dependent stabilization of platelet thrombi. PMID:24723492

  17. [Significance of tube manometry in the assessment of tube function. A comparison of tube manometry results and continuous direct determination of pressure in the middle ear].

    PubMed

    Koch, U

    1983-04-01

    Tube manometry--also known as aspiration-deflation-test--is an often used, practicable clinical test for tube function. By comparing tube manometric results with continual measurements of the middle ear pressure, a close correlation between both test results could be demonstrated. Tube manometric tests thus permit an estimation of the tube function as well as of the probable development of the middle ear pressure. An exact classification in terms of physiologic and pathologic tube function, however, is not possible. It is clear that even a partial equalization of low-pressure values in tube manometry should be interpreted as physiologic.

  18. Multi-tube fuel nozzle with mixing features

    SciTech Connect

    Hughes, Michael John

    2014-04-22

    A system includes a multi-tube fuel nozzle having an inlet plate and a plurality of tubes adjacent the inlet plate. The inlet plate includes a plurality of apertures, and each aperture includes an inlet feature. Each tube of the plurality of tubes is coupled to an aperture of the plurality of apertures. The multi-tube fuel nozzle includes a differential configuration of inlet features among the plurality of tubes.

  19. Flexible tubing production system for well installation

    SciTech Connect

    Walling, J. B.

    1984-10-16

    An improved system for lifting formation fluid from a well bore to a surface facility is disclosed. Rigid production tubing and sucker rods are replaced by flexible, composite production tubing in which a production conduit, power conductors, signal conductors, hydraulic/pneumatic conduits and a load-bearing tension member are enclosed by a flexible, tubular covering. The load-bearing member of the flexible production tubing is mechanically coupled to a submersible pump. The pump includes driving means such as an electrical motor, hydraulic motor or pneumatic motor which is driven downhole by electrical or hydraulic/pneumatic power transmitted through auxiliary conduits in the flexible production tubing. The flexible production tubing is wound about a truck-mounted reel for convenient transport to and from a well site. A submersible pump is attached to the end of the flexible tubing and is played out from the reel through the well casing to the producing formation. Withdrawal of the pump from the well is accomplished by taking up the flexible production tubing around the truck-mounted reel.

  20. Investigating the Dynamics of Canonical Flux Tubes

    NASA Astrophysics Data System (ADS)

    von der Linden, Jens; Carroll, Evan; Kamikawa, Yu; Lavine, Eric; Vereen, Keon; You, Setthivoine

    2013-10-01

    Canonical flux tubes are defined by tracing areas of constant magnetic and fluid vorticity flux. This poster will present the theory for canonical flux tubes and current progress in the construction of an experiment designed to observe their evolution. In the zero flow limit, canonical flux tubes are magnetic flux tubes, but in full form, present the distinct advantage of reconciling two-fluid plasma dynamics with familiar concepts of helicity, twists and linkages. The experiment and the DCON code will be used to investigate a new MHD stability criterion for sausage and kink modes in screw pinches that has been generalized to magnetic flux tubes with skin and core currents. Camera images and a 3D array of ˙ B probes will measure tube aspect-ratio and ratio of current-to-magnetic flux, respectively, to trace these flux tube parameters in a stability space. The experiment's triple electrode planar gun is designed to generate azimuthal and axial flows. These diagnostics together with a 3D vector tomographic reconstruction of ion Doppler spectroscopy will be used to verify the theory of canonical helicity transport. This work was sponsored in part by the US DOE Grant DE-SC0010340.

  1. Steam generator tubing NDE performance

    SciTech Connect

    Henry, G.; Welty, C.S. Jr.

    1997-02-01

    Steam generator (SG) non-destructive examination (NDE) is a fundamental element in the broader SG in-service inspection (ISI) process, a cornerstone in the management of PWR steam generators. Based on objective performance measures (tube leak forced outages and SG-related capacity factor loss), ISI performance has shown a continually improving trend over the years. Performance of the NDE element is a function of the fundamental capability of the technique, and the ability of the analysis portion of the process in field implementation of the technique. The technology continues to improve in several areas, e.g. system sensitivity, data collection rates, probe/coil design, and data analysis software. With these improvements comes the attendant requirement for qualification of the technique on the damage form(s) to which it will be applied, and for training and qualification of the data analysis element of the ISI process on the field implementation of the technique. The introduction of data transfer via fiber optic line allows for remote data acquisition and analysis, thus improving the efficiency of analysis for a limited pool of data analysts. This paper provides an overview of the current status of SG NDE, and identifies several important issues to be addressed.

  2. Atmosphere in a Test Tube

    NASA Astrophysics Data System (ADS)

    Claudi, R.; Pace, E.; Ciaravella, A.; Micela, G.; Piccioni, G.; Billi, D.; Cestelli Guidi, M.; Coccola, L.; Erculiani, M. S.; Fedel, M.; Galletta, G.; Giro, E.; La Rocca, N.; Morosinotto, T.; Poletto, L.; Schierano, D.; Stefani, S.

    The ancestor philosophers' dream of thousand of new world is finally realised: more than 1800 extrasolar planets have been discovered in the neighborhood of our Sun. Most of them are very different from those we used to know in our Solar System. Others orbit the Habitable Zone (HZ) of their parent stars. Space missions, as JWST and the very recently proposed ARIEL, or ground based instruments, like SPHERE@VLT, GPI@GEMINI and EPICS@ELT, have been proposed and built to measure the atmospheric transmission, reflection and emission spectra over a wide wavelength range of these new worlds. In order to interpret the spectra coming out by this new instrumentation, it is important to know in detail the optical characteristics of gases in the typical physical conditions of the planetary atmospheres and how those characteristics could be affected by radiation driven photochemical and bio-chemical reaction. Insights in this direction can be achieved from laboratory studies of simulated planetary atmosphere of different pressure and temperature conditions under the effects of radiation sources, used as proxies of different bands of the stellar emission. ''Atmosphere in a Test Tube'' is a collaboration among several Italian astronomical, biological and engineering institutes in order to share their experiencece in performing laboratory experiments on several items concerning extrasolar planet atmospheres.

  3. [Modern technics of tube feeding].

    PubMed

    Troidl, H; Vestweber, K H; Sommer, H; Tepner, S

    1984-03-01

    A prospective study was done in 101 patients and clinical usefulness of a fine needle-catheter-jejunostomy was investigated; this procedure was modified according to the procedure devised by Delany (2). The instruments used were two split canules and a polyurethane catheter (inner diameter 2.1 mm); these instruments are simple, safe and can be applied quickly. Formation of fistulae, peritonitis, ileus or deaths caused by the procedure could not be observed. The catheter needs to have certain mechanical qualities as e.g. sufficient rigidity. Percutaneous endoscopic gastrostomy is an alternative to corresponding surgery procedure. The stomach is punctured under sight and a Foley catheter is applied immediately. We performed this procedure without major complications in seven cases, and found it to be very useful. The techniques described here are essentially important if the advantages of the enteral as compared to the parenteral nutrition are to be made use of. As soon as the problems of diarrhea and belching are solved, tube feeding will offer in the near future a real alternative to parenteral nutrition, especially in patients who need long time artificial nutrition.

  4. Transport logistics in pollen tubes.

    PubMed

    Chebli, Youssef; Kroeger, Jens; Geitmann, Anja

    2013-07-01

    Cellular organelles move within the cellular volume and the effect of the resulting drag forces on the liquid causes bulk movement in the cytosol. The movement of both organelles and cytosol leads to an overall motion pattern called cytoplasmic streaming or cyclosis. This streaming enables the active and passive transport of molecules and organelles between cellular compartments. Furthermore, the fusion and budding of vesicles with and from the plasma membrane (exo/endocytosis) allow for transport of material between the inside and the outside of the cell. In the pollen tube, cytoplasmic streaming and exo/endocytosis are very active and fulfill several different functions. In this review, we focus on the logistics of intracellular motion and transport processes as well as their biophysical underpinnings. We discuss various modeling attempts that have been performed to understand both long-distance shuttling and short-distance targeting of organelles. We show how the combination of mechanical and mathematical modeling with cell biological approaches has contributed to our understanding of intracellular transport logistics.

  5. Photomultiplier Tubes: Calibration and Neutrino Physics

    SciTech Connect

    Damon, Edward; Maricic, Jelena

    2010-03-30

    Photomultiplier Tubes are devices designed to amplify very small light signals, on the order of single photons, to levels that are detectable by conventional electronics. Such a high level of amplification, however, comes with a quite a few potential problems, as the relationship between a light signal in and the current out- the response of the system- can be difficult to determine, meaning that photomultiplier tubes' use in scientific research requires a great deal of sensitive calibration. Once calibrated, the photomultiplier tube is a tool that can be used on a number of interesting problems, including the field of neutrino physics. This work deals with the use of photomultiplier tubes' use in the upcoming Double Chooz experiment to determine the mixing angle theta{sub 13}, between different neutrino mass eigenstates. Calibration of the tubes requires measurement of the charge characteristics, most notably, the gain, pedestal, and the dark rate of a tube. Moreover, for all modern tubes, there is an additional feature which can be used to calibrate the system, the single photo electron peak, which describes the response of the tube to a single photon. Some theories predict higher order effects, in addition to the single photoelectron peak, including things like incomplete multiplication of a single photon electron, features which are theoretically able to be determined by a detailed examination of the single photoelectron peak. This paper goes through the methods of calibrating a phototubes both with and without a single photoelectron peak, and is unable to determine conclusively whether or not partial multiplication is able to explain certain features of photomultiplier tubes with a single photoelectron peak.

  6. Bacterial corrosion of reformer heater tubes

    SciTech Connect

    Ghassem, H.; Adibi, N.

    1995-03-01

    Soon after going on stream, two tubes in a heater convection bank, which had been reassembled using reclaimed tubes, started to leak and caused a fire. The tubes were made of AISI 304H stainless steel 4.5 in. diam by 0.25 in. thick. Preliminary visual inspection of the failed tubes revealed a few barely detectable pinholes on the external surfaces. Cutting the tubes at various sections near the pinholes revealed more specific features of corrosion. Each of the detected surface pinholes led to a subsurface cavity or gap, which when sectioned, resembled a bottle-shaped cavity. Corrosion had formed a number of tunnels and cavities within the tube wall, all interconnected through minute pathways, and had progressed along the tube length. On the internal surface of the failed tubes, a fairly large hole had opened to one of the corrosion cavities. Microstructural examination showed that the tube material had been sensitized and that the corrosion had progressed foremost along chromium-depleted zones next to grain boundaries. Scanning electron microscopy (SEM) on a bent-open minute corrosion crack revealed numerous scattered bright spots with definite shape and size on the exposed surfaces, which were very similar to sulfate-reducing bacteria (SRB). Although the heater had run for some time before its failure, the remains of bacteria on the exposed crack surfaces was quite obvious. Furthermore, analytical studies by means of SEM-energy dispersive x-ray analysis, clearly revealed sulfur inside the smaller cavities or gaps where corrosion products had remained intact.

  7. Gastrostomy Tube Placement Without Nasogastric Tube: A Retrospective Evaluation in 85 Patients

    SciTech Connect

    Heberlein, Wolf E. Goodwin, Whitney J.; Wood, Clint E.; Yousaf, Muhammad; Culp, William C.

    2012-12-15

    Purpose: Our study evaluated techniques for percutaneous gastrostomy (G)-tube placement without the use of a nasogastric (NG) tube. Instead, direct puncture of a physiologic air bubble or effervescent-enhanced gastric bubble distention was performed in patients with upper digestive tract obstruction (UDTO) or psychological objections to NG tubes. Materials and Methods: A total of 886 patients underwent G-tube placement in our department during a period of 7 years. We present our series of 85 (9.6%) consecutive patients who underwent percutaneous G-tube placement without use of an NG tube. Results: Of these 85 patients, fluoroscopic guided access was attempted by direct puncture of a physiologically present gastric air bubble in 24 (28%) cases. Puncture of an effervescent-induced large gastric air bubble was performed in 61 (72%) patients. Altogether, 82 (97%) of 85 G tubes were successfully placed in this fashion. The three failures comprised refusal of effervescent, vomiting of effervescent, and one initial tube misplacement when a deviation from our standard technique occurred. Conclusion: The described techniques compare favorably with published large series on G-tube placement with an NG tube in place. The techniques are especially suited for patients with UDTO due to head, neck, or esophageal malignancies, but they should be considered as an alternative in all patients. Direct puncture of effervescent-enhanced gastric bubble distention is a safe, patient-friendly and effective technique.

  8. [Fallopian tube disease on magnetic resonance imaging].

    PubMed

    La Parra Casado, C; Molina Fàbrega, R; Forment Navarro, M; Cano Gimeno, J

    2013-09-01

    Knowledge about fallopian tube disease is essential in the assessment of the pelvis in female patients. Primary and secondary changes in the tubes vary widely, regardless of whether associated changes in the ovaries are present. Ultrasonography is the initial technique in the study of adnexal disease because it is very sensitive and widely available; however, MRI is also very useful in this context because its high tissue resolution and anatomic detail make it more specific. The morphologic findings and the characteristics of the contents of the tubes on MRI enable a more accurate diagnosis or limit the differential diagnosis, helping to ensure that the most appropriate treatment is provided in each case.

  9. Preparation of bioabsorbable nerve guide tubes.

    PubMed

    Luciano, R M; de Carvalho Zavaglia, C A; de Rezende Duek, E A

    2000-03-01

    The use of bioabsorbable polymers in applications as temporary structural function, recovering damage in live tissues, is a promising research area. Membranes of poly(lactic acid) (PLA) may act as support to adhesion and cellular invasion or as devices for guided tissue regeneration (GTR). In this study, the same casting technique used to prepare membranes was used to prepare PLA tubes. These tubes can be used for tests in nerve guided regeneration (NGR). To improve flexibility of the device, a bioabsorbable plasticizer was added to the polymer. The initial results showed that the proposed technique allowed the preparation of flexible tubes that can be used for NGR. PMID:10759642

  10. Utility of Lava Tubes on Other Worlds

    NASA Technical Reports Server (NTRS)

    Walden, Bryce E.; Billings, T. L.; York, Cheryl Lynn; Gillett, S. L.; Herbert, M. V.

    1998-01-01

    On Mars, as on Earth, lava tubes are found in the extensive lava fields associated with shield volcanism. Lunar lava-tube traces are located near mare-highland boundaries, giving access to a variety of minerals and other resources, including steep slopes, prominent heights for local area communications and observation, large-surface areas in shade, and abundant basalt plains suitable for landing sites, mass-drivers, surface transportation, regolith harvesting, and other uses. Methods for detecting lava tubes include visual observations of collapse trenches and skylights, ground-penetrating radar, gravimetry, magnetometry, seismography, atmospheric effects, laser, lidar, infrared, and human or robotic exploration.

  11. Starter for inductively coupled plasma tube

    DOEpatents

    Hull, Donald E.; Bieniewski, Thomas M.

    1988-01-01

    A starter assembly is provided for use with an inductively coupled plasma (ICP) tube to reliably initate a plasma at internal pressures above about 30 microns. A conductive probe is inserted within the inductor coil about the tube and insulated from the tube shield assembly. A capacitive circuit is arranged for momentarily connecting a high voltage radio-frequency generator to the probe while simultaneously energizing the coil. When the plasma is initiated the probe is disconnected from the generator and electrically connected to the shield assembly for operation.

  12. Scintillation probe with photomultiplier tube saturation indicator

    DOEpatents

    Ruch, Jeffrey F.; Urban, David J.

    1996-01-01

    A photomultiplier tube saturation indicator is formed by supplying a supplemental light source, typically an light emitting diode (LED), adjacent to the photomultiplier tube. A switch allows the light source to be activated. The light is forwarded to the photomultiplier tube by an optical fiber. If the probe is properly light tight, then a meter attached to the indicator will register the light from the LED. If the probe is no longer light tight, and the saturation indicator is saturated, no signal will be registered when the LED is activated.

  13. Starter for inductively coupled plasma tube

    DOEpatents

    Hull, D.E.; Bieniewski, T.M.

    1988-08-23

    A starter assembly is provided for use with an inductively coupled plasma (ICP) tube to reliably initiate a plasma at internal pressures above about 30 microns. A conductive probe is inserted within the inductor coil about the tube and insulated from the tube shield assembly. A capacitive circuit is arranged for momentarily connecting a high voltage radio-frequency generator to the probe while simultaneously energizing the coil. When the plasma is initiated the probe is disconnected from the generator and electrically connected to the shield assembly for operation. 1 fig.

  14. Collective cell migration requires suppression of actomyosin at cell-cell contacts mediated by DDR1 and the cell polarity regulators Par3 and Par6.

    PubMed

    Hidalgo-Carcedo, Cristina; Hooper, Steven; Chaudhry, Shahid I; Williamson, Peter; Harrington, Kevin; Leitinger, Birgit; Sahai, Erik

    2011-01-01

    Collective cell migration occurs in a range of contexts: cancer cells frequently invade in cohorts while retaining cell-cell junctions. Here we show that collective invasion by cancer cells depends on decreasing actomyosin contractility at sites of cell-cell contact. When actomyosin is not downregulated at cell-cell contacts, migrating cells lose cohesion. We provide a molecular mechanism for this downregulation. Depletion of discoidin domain receptor 1 (DDR1) blocks collective cancer-cell invasion in a range of two-dimensional, three-dimensional and 'organotypic' models. DDR1 coordinates the Par3/Par6 cell-polarity complex through its carboxy terminus, binding PDZ domains in Par3 and Par6. The DDR1-Par3/Par6 complex controls the localization of RhoE to cell-cell contacts, where it antagonizes ROCK-driven actomyosin contractility. Depletion of DDR1, Par3, Par6 or RhoE leads to increased actomyosin contactility at cell-cell contacts, a loss of cell-cell cohesion and defective collective cell invasion.

  15. ParABS Systems of the Four Replicons of Burkholderia cenocepacia: New Chromosome Centromeres Confer Partition Specificity†

    PubMed Central

    Dubarry, Nelly; Pasta, Franck; Lane, David

    2006-01-01

    Most bacterial chromosomes carry an analogue of the parABS systems that govern plasmid partition, but their role in chromosome partition is ambiguous. parABS systems might be particularly important for orderly segregation of multipartite genomes, where their role may thus be easier to evaluate. We have characterized parABS systems in Burkholderia cenocepacia, whose genome comprises three chromosomes and one low-copy-number plasmid. A single parAB locus and a set of ParB-binding (parS) centromere sites are located near the origin of each replicon. ParA and ParB of the longest chromosome are phylogenetically similar to analogues in other multichromosome and monochromosome bacteria but are distinct from those of smaller chromosomes. The latter form subgroups that correspond to the taxa of their hosts, indicating evolution from plasmids. The parS sites on the smaller chromosomes and the plasmid are similar to the “universal” parS of the main chromosome but with a sequence specific to their replicon. In an Escherichia coli plasmid stabilization test, each parAB exhibits partition activity only with the parS of its own replicon. Hence, parABS function is based on the independent partition of individual chromosomes rather than on a single communal system or network of interacting systems. Stabilization by the smaller chromosome and plasmid systems was enhanced by mutation of parS sites and a promoter internal to their parAB operons, suggesting autoregulatory mechanisms. The small chromosome ParBs were found to silence transcription, a property relevant to autoregulation. PMID:16452432

  16. Transcriptional Profiling of ParA and ParB Mutants in Actively Dividing Cells of an Opportunistic Human Pathogen Pseudomonas aeruginosa

    PubMed Central

    Bartosik, Aneta A.; Glabski, Krzysztof; Jecz, Paulina; Mikulska, Sylwia; Fogtman, Anna; Koblowska, Marta; Jagura-Burdzy, Grazyna

    2014-01-01

    Accurate chromosome segregation to progeny cells is a fundamental process ensuring proper inheritance of genetic material. In bacteria with simple cell cycle, chromosome segregation follows replication initiation since duplicated oriC domains start segregating to opposite halves of the cell soon after they are made. ParA and ParB proteins together with specific DNA sequences are parts of the segregation machinery. ParA and ParB proteins in Pseudomonas aeruginosa are important for optimal growth, nucleoid segregation, cell division and motility. Comparative transcriptome analysis of parAnull and parBnull mutants versus parental P. aeruginosa PAO1161 strain demonstrated global changes in gene expression pattern in logarithmically growing planktonic cultures. The set of genes similarly affected in both mutant strains is designated Par regulon and comprises 536 genes. The Par regulon includes genes controlled by two sigma factors (RpoN and PvdS) as well as known and putative transcriptional regulators. In the absence of Par proteins, a large number of genes from RpoS regulon is induced, reflecting the need for slowing down the cell growth rate and decelerating the metabolic processes. Changes in the expression profiles of genes involved in c-di-GMP turnover point out the role of this effector in such signal transmission. Microarray data for chosen genes were confirmed by RT-qPCR analysis. The promoter regions of selected genes were cloned upstream of the promoter-less lacZ gene and analyzed in the heterologous host E. coliΔlac. Regulation by ParA and ParB of P. aeruginosa was confirmed for some of the tested promoters. Our data demonstrate that ParA and ParB besides their role in accurate chromosome segregation may act as modulators of genes expression. Directly or indirectly, Par proteins are part of the wider regulatory network in P. aeruginosa linking the process of chromosome segregation with the cell growth, division and motility. PMID:24498062

  17. Is PAR a Good Investment? Understanding the Costs and Benefits of Teacher Peer Assistance and Review Programs

    ERIC Educational Resources Information Center

    Papay, John P.; Johnson, Susan Moore

    2012-01-01

    Peer Assistance and Review (PAR) is a local labor-management initiative designed to improve teacher quality. In PAR, expert "consulting teachers" mentor, support, and evaluate novice and underperforming veteran teachers. Evaluations under PAR can lead to dismissals. The authors examine the costs and benefits of PAR, both financial and…

  18. Siphon flows in isolated magnetic flux tubes. IV - Critical flows with standing tube shocks

    SciTech Connect

    Thomas, J.H.; Montesinos, B. Mees Observatory, NY Oxford, University )

    1991-07-01

    Critical siphon flows in arched, isolated magnetic flux tubes are studied within the thin flux tube approximation, with a view toward applications to intense magnetic flux concentrations in the solar photosphere. The results of calculations of the strength and position of the standing tube shock in the supercritical downstream branch of a critical siphon flow are presented, as are calculations of the flow variables all along the flux tube and the equilibrium path of the flux tube in the surrounding atmosphere. It is suggested that arched magnetic flux tubes, with magnetic field strength increased by a siphon flow, may be associated with some of the intense, discrete magnetic elements observed in the solar photosphere. 37 refs.

  19. Siphon flows in isolated magnetic flux tubes. IV - Critical flows with standing tube shocks

    NASA Technical Reports Server (NTRS)

    Thomas, John H.; Montesinos, Benjamin

    1991-01-01

    Critical siphon flows in arched, isolated magnetic flux tubes are studied within the thin flux tube approximation, with a view toward applications to intense magnetic flux concentrations in the solar photosphere. The results of calculations of the strength and position of the standing tube shock in the supercritical downstream branch of a critical siphon flow are presented, as are calculations of the flow variables all along the flux tube and the equilibrium path of the flux tube in the surrounding atmosphere. It is suggested that arched magnetic flux tubes, with magnetic field strength increased by a siphon flow, may be associated with some of the intense, discrete magnetic elements observed in the solar photosphere.

  20. Chemical milling of zircaloy tubing to produce integral OD spiral finned tubes. AWBA development program

    NASA Astrophysics Data System (ADS)

    Horwood, W. A.

    1982-02-01

    A detailed process description is provided for producing integral spiral fins on the outside surface of Zircaloy nuclear fuel cladding tubes by masking with pressure sensitive tape strips and then chemical milling (pickling) the tube wall between the tape strips to leave the fins in relief. Fins up to 0.020 inch high by 0.05 to 0.12 inch wide were consistently produced on tubes having wall thickness of 0.008 inch or greater after fin pickling. Wall thickness uniformity was excellent. Information is provided on tube surface preparation to maximize tape mask adhesion time during pickling, acid chemistry control to prevent local tube wall thinning near the fin, and pickling techniques to promote uniform material removal. Simple fixture designs are described for quickly and conveniently applying the tape strips to the tube wall in an accurate spiral.

  1. Inspection of irradiated P-7 fuel tubes

    SciTech Connect

    Peacock, H.B.; Sturcken, E.F.

    1980-08-20

    Mark 16 U-A1 alloy production fuel tubes and six special U{sub 3}O{sub 8}-A1 powder metallurgy (PM) test assemblies were successfully irradiated in P-7 reactor charge beginning December 1976. A year after irradiation, the outer surfaces were inspected under water in P-Area basin. Inspection showed that a black'' oxide had formed on the bottom {sup {approximately}}2/3 and flaked off in some areas for both the production and PM tubes. A small cladding defect was also observed on one PM outer tube near the bottom. Sections were cut from the tubes and metallographically examined in the SRL High Level Caves (HLC). This report gives results of the examinations. 8 refs., 9 figs., 1 tab.

  2. Automatic welding of stainless steel tubing

    NASA Technical Reports Server (NTRS)

    Clautice, W. E.

    1978-01-01

    The use of automatic welding for making girth welds in stainless steel tubing was investigated as well as the reduction in fabrication costs resulting from the elimination of radiographic inspection. Test methodology, materials, and techniques are discussed, and data sheets for individual tests are included. Process variables studied include welding amperes, revolutions per minute, and shielding gas flow. Strip chart recordings, as a definitive method of insuring weld quality, are studied. Test results, determined by both radiographic and visual inspection, are presented and indicate that once optimum welding procedures for specific sizes of tubing are established, and the welding machine operations are certified, then the automatic tube welding process produces good quality welds repeatedly, with a high degree of reliability. Revised specifications for welding tubing using the automatic process and weld visual inspection requirements at the Kennedy Space Center are enumerated.

  3. Performance of a tapered pulse tube

    SciTech Connect

    Swift, G.; Allen, M.; Woolan, J.J.

    1998-02-01

    In a well instrumented pulse tube refrigerator having 1,500 W of cooling power at 125 K, the authors have measured the figure of merit of a tapered pulse tube at several operating points. At operating points near the operating point for which the taper was designed, the figure of merit is 0.96. This is close to the theoretical optimum figure of merit 0.97 calculated for this pulse tube considering only two loss mechanisms: heat conduction in the metal pulse tube wall and ordinary thermoacoustic heat transport in the gas within a few thermal penetration depths of the wall. At operating points farther from the design operating point, the measured figure of merit is much lower, as streaming driven convection adds a third loss mechanism.

  4. A review of pulse tube refrigeration

    NASA Technical Reports Server (NTRS)

    Radebaugh, Ray

    1990-01-01

    This paper reviews the development of the three types of pulse tube refrigerators: basic, resonant, and orifice types. The principles of operation are given. It is shown that the pulse tube refrigerator is a variation of the Stirling-cycle refrigerator, where the moving displacer is substituted by a heat transfer mechanism or by an orifice to bring about the proper phase shifts between pressure and mass flow rate. A harmonic analysis with phasors is described which gives reasonable results for the refrigeration power, yet is simple enough to make clear the processes which give rise to the refrigeration. The efficiency and refrigeration power are compared with those of other refrigeration cycles. A brief review is given of the research being done at various laboratories on both one- and two-stage pulse tubes. A preliminary assessment of the role of pulse tube refrigerators is discussed.

  5. The Choking Game on YouTube

    PubMed Central

    Defenderfer, Ellen K.; Austin, Jillian E.; Davies, W. Hobart

    2016-01-01

    The choking game (TCG) is an adolescent activity in which asphyxiation is used to obtain a “high,” occasionally resulting in seizures or death. A plethora of TCG information is available through YouTube, though this content has not been evaluated recently. The current study described TCG as portrayed in YouTube videos and compared views and ratings of TCG videos to unrelated videos. The TCG videos demonstrated diverse methods of asphyxiation, with a minority showing injury to the participants. TCG videos were less likely to be commented on or rated positively than non–choking game videos. TCG prevention videos differed significantly from actual TCG videos in the way they depicted the social context of TCG. Thus, TCG videos are accessible through YouTube, but the prevention materials available on YouTube are not accurate or representative. Accurate and educational online prevention materials should be created to decrease the occurrence of TCG. PMID:27335992

  6. Collapse of composite tubes under end moments

    NASA Technical Reports Server (NTRS)

    Stockwell, Alan E.; Cooper, Paul A.

    1992-01-01

    Cylindrical tubes of moderate wall thickness such as those proposed for the original space station truss, may fail due to the gradual collapse of the tube cross section as it distorts under load. Sometimes referred to as the Brazier instability, it is a nonlinear phenomenon. This paper presents an extension of an approximate closed form solution of the collapse of isotropic tubes subject to end moments developed by Reissner in 1959 to include specially orthotropic material. The closed form solution was verified by an extensive nonlinear finite element analysis of the collapse of long tubes under applied end moments for radius to thickness ratios and composite layups in the range proposed for recent space station truss framework designs. The finite element analysis validated the assumption of inextensional deformation of the cylindrical cross section and the approximation of the material as specially orthotropic.

  7. YouTube and ‘psychiatry’

    PubMed Central

    Gordon, Robert; Miller, John; Collins, Noel

    2015-01-01

    YouTube is a video-sharing website that is increasingly used to share and disseminate health-related information, particularly among younger people. There are reports that social media sites, such as YouTube, are being used to communicate an anti-psychiatry message but this has never been confirmed in any published analysis of YouTube clip content. This descriptive study revealed that the representation of ‘psychiatry’ during summer 2012 was predominantly negative. A subsequent smaller re-analysis suggests that the negative portrayal of ‘psychiatry’ on YouTube is a stable phenomenon. The significance of this and how it could be addressed are discussed. PMID:26755987

  8. Fewer Advanced Alzheimer's Patients on Feeding Tubes

    MedlinePlus

    ... at someone in the advanced stages of a terminal illness, a feeding tube doesn't make a ... of palliative care (keeping a person with a terminal illness as comfortable as possible), Mitchell said. As ...

  9. Folic Acid Helps Prevent Neural Tube Defects

    MedlinePlus

    ... Features Folic Acid Helps Prevent Neural Tube Defects Language: English Español (Spanish) Recommend on Facebook Tweet Share Compartir The feature you selected is no longer available. In 10 seconds you will be automatically redirected to the CDC. ...

  10. Combined mechanical loading of composite tubes

    NASA Technical Reports Server (NTRS)

    Derstine, Mark S.; Pindera, Marek-Jerzy; Bowles, David E.

    1988-01-01

    An analytical/experimental investigation was performed to study the effect of material nonlinearities on the response of composite tubes subjected to combined axial and torsional loading. The effect of residual stresses on subsequent mechanical response was included in the investigation. Experiments were performed on P75/934 graphite-epoxy tubes with a stacking sequence of (15/0/ + or - 10/0/ -15), using pure torsion and combined axial/torsional loading. In the presence of residual stresses, the analytical model predicted a reduction in the initial shear modulus. Experimentally, coupling between axial loading and shear strain was observed in laminated tubes under combined loading. The phenomenon was predicted by the nonlinear analytical model. The experimentally observed linear limit of the global shear response was found to correspond to the analytically predicted first ply failure. Further, the failure of the tubes was found to be path dependent above a critical load level.

  11. Cardboard Tubes: Bring Geometry from Home.

    ERIC Educational Resources Information Center

    Hayes, Nakonia

    1998-01-01

    Presents an activity using the cardboard tube from a roll of bathroom tissue or paper towels to help students examine and extend their understanding of the geometric properties of parallelograms. (ASK)

  12. Energy absorber uses expanded coiled tube

    NASA Technical Reports Server (NTRS)

    Johnson, E. F.

    1972-01-01

    Mechanical shock mitigating device, based on working material to its failure point, absorbs mechanical energy by bending or twisting tubing. It functions under axial or tangential loading, has no rebound, is area independent, and is easy and inexpensive to build.

  13. Laboratory Applications of the Vortex Tube.

    ERIC Educational Resources Information Center

    Bruno, Thomas J.

    1987-01-01

    Discussed are a brief explanation of the function of the vortex tube and some applications for the chemistry laboratory. It is a useful and inexpensive solution to many small-scale laboratory heating and cooling applications. (RH)

  14. 21 CFR 868.5975 - Ventilator tubing.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    .... Ventilator tubing is a device intended for use as a conduit for gases between a ventilator and a patient during ventilation of the patient. (b) Classification. Class I (general controls). The device is...

  15. Time-shared Cathode Ray Tube

    NASA Technical Reports Server (NTRS)

    Herndon, E. S.

    1969-01-01

    Time-shared cathode tube provides high quality display at low cost display stations which utilize television moniters. It updates a cluster of graphic displays from a computer and is useful in systems not equipped for graphics time-sharing.

  16. Lunar lava tube radiation safety analysis.

    PubMed

    De Angelis, Giovanni; Wilson, J W; Clowdsley, M S; Nealy, J E; Humes, D H; Clem, J M

    2002-12-01

    For many years it has been suggested that lava tubes on the Moon could provide an ideal location for a manned lunar base, by providing shelter from various natural hazards, such as cosmic radiation, meteorites, micrometeoroids, and impact crater ejecta, and also providing a natural environmental control, with a nearly constant temperature, unlike that of the lunar surface showing extreme variation in its diurnal cycle. An analysis of radiation safety issues on lunar lava tubes has been performed by considering radiation from galactic cosmic rays (GCR) and Solar Particle Events (SPE) interacting with the lunar surface, modeled as a regolith layer and rock. The chemical composition has been chosen as typical of the lunar regions where the largest number of lava tube candidates are found. Particles have been transported all through the regolith and the rock, and received particles flux and doses have been calculated. The radiation safety of lunar lava tubes environments has been demonstrated.

  17. Staged multi-tube premixing injector

    DOEpatents

    Zuo, Baifang; Khan, Abdul Rafey; York, William David; Ziminsky, Willy Steve

    2012-10-02

    A fuel injection nozzle includes a body member having an upstream wall opposing a downstream wall, and an internal wall disposed between the upstream wall and the downstream wall, a first chamber partially defined by the an inner surface of the upstream wall and a surface of the internal wall, a second chamber partially defined by an inner surface of the downstream wall and a surface of the internal wall a first gas inlet communicative with the first chamber operative to emit a first gas into the first chamber, a second gas inlet communicative with the second chamber operative to emit a second gas into the second chamber, and a plurality of mixing tubes, each of the mixing tubes having a tube inner surface, a tube outer surface, a first inlet communicative with an aperture in the upstream wall operative to receive a third gas.

  18. Sample inlet tube for ion source

    DOEpatents

    Prior, David [Hermiston, OR; Price, John [Richland, WA; Bruce, Jim [Oceanside, CA

    2002-09-24

    An improved inlet tube is positioned within an aperture through the device to allow the passage of ions from the ion source, through the improved inlet tube, and into the interior of the device. The inlet tube is designed with a larger end and a smaller end wherein the larger end has a larger interior diameter than the interior diameter of the smaller end. The inlet tube is positioned within the aperture such that the larger end is pointed towards the ion source, to receive ions therefrom, and the smaller end is directed towards the interior of the device, to deliver the ions thereto. Preferably, the ion source utilized in the operation of the present invention is a standard electrospray ionization source. Similarly, the present invention finds particular utility in conjunction with analytical devices such as mass spectrometers.

  19. Advanced Illness: Feeding Tubes and Ventilators

    MedlinePlus

    ... Address, Jewish Lights Publishing, 2000. www.jewishlights.com Bioethics , Thomas Shannon, ed. Paulist Press, 2009 Swallowing Problems , ... 2004 The Feeding Tube Dilemma, The Center for Bioethics and Human Dignity, 1/27/06, cbhd.org ...

  20. A model for the condensation of the bacterial chromosome by the partitioning protein ParB

    NASA Astrophysics Data System (ADS)

    Broedersz, Chase; Wingreen, Ned

    2013-03-01

    The molecular machinery responsible for faithful segregation of the chromosome in bacteria such as Caulobacter crescentus and Bacillus subtilis includes the ParABS a.k.a. Spo0J/Soj partitioning system. In Caulobacter, prior to division, hundreds of ParB proteins bind to the DNA near the origin of replication, and localize to one pole of the cell. Subsequently, the ParB-DNA complex is translocated to the far pole by the binding and retraction of the ParA spindle-like apparatus. Remarkably, the localization of ParB proteins to specific regions of the chromosome appears to be controlled by only a few centromeric parS binding sites. Although lateral interactions between DNA-bound ParB are likely to be important for their localization, the long-range order of ParB domains on the chromosome appears to be inconsistent with a picture in which protein-protein interactions are limited to neighboring DNA-bound proteins. We developed a coarse-grained Brownian dynamics model that allows for lateral and 3D protein-protein interactions among bound ParB proteins. Our model shows how such interactions can condense and organize the DNA spatially, and can control the localization and the long-range order of the DNA-bound proteins.