Bed-material entrainment potential, Roaring Fork River at Basalt, Colorado

USGS Publications Warehouse

Elliott, John G.

2002-01-01

The Roaring Fork River at Basalt, Colorado, has a frequently mobile streambed composed of gravel, cobbles, and boulders. Recent urban and highway development on the flood plain, earlier attempts to realign and confine the channel, and flow obstructions such as bridge openings and piers have altered the hydrology, hydraulics, sediment transport, and sediment deposition areas of the Roaring Fork. Entrainment and deposition of coarse sediment on the streambed and in large alluvial bars have reduced the flood-conveying capacity of the river. Previous engineering studies have identified flood-prone areas and hazards related to inundation and high streamflow velocity, but those studies have not evaluated the potential response of the channel to discharges that entrain the coarse streambed. This study builds upon the results of earlier flood studies and identifies some potential areas of concern associated with bed-material entrainment. Cross-section surveys and simulated water-surface elevations from a previously run HEC?RAS model were used to calculate the boundary shear stress on the mean streambed, in the thalweg, and on the tops of adjacent alluvial bars for four reference streamflows. Sediment-size characteristics were determined for surficial material on the streambed, on large alluvial bars, and on a streambank. The median particle size (d50) for the streambed samples was 165 millimeters and for the alluvial bars and bank samples was 107 millimeters. Shear stresses generated by the 10-, 50-, and 100-year floods, and by a more common flow that just inundated most of the alluvial bars in the study reach were calculated at 14 of the cross sections used in the Roaring Fork River HEC?RAS model. The Shields equation was used with a Shields parameter of 0.030 to estimate the critical shear stress for entrainment of the median sediment particle size on the mean streambed, in the thalweg, and on adjacent alluvial bar surfaces at the 14 cross sections. Sediment-entrainment potential for a specific geomorphic surface was expressed as the ratio of the flood-generated boundary shear stress to the critical shear stress (to/tc) with respect to two threshold conditions. The partial entrainment threshold (to/tc=1) is the condition where the mean boundary shear stress (to) equals the critical shear stress for the median particle size (tc) at that cross section. At this threshold discharge, the d50 particle size becomes entrained, but movement of d50-size particles may be limited to a few individual particles or in a small area of the streambed surface. The complete entrainment threshold (to/tc=2) is the condition where to is twice the critical shear stress for the median particle size, the condition where complete or widespread mobilization of the d50 particle-size fraction is anticipated. Entrainment potential for a specific reference streamflow varied greatly in the downstream direction. At some cross sections, the bed or bar material was mobile, whereas at other cross sections, the bed or bar material was immobile for the same discharge. The significance of downstream variability is that sediment entrained at one cross section may be transported into, but not through, a cross section farther downstream, a situation resulting in sediment deposition and possibly progressive aggradation and loss of channel conveyance. Little or no sediment in the d50-size range is likely to be entrained or transported through much of the study reach by the bar-inundating streamflow. However, the entrainment potential at this discharge increases abruptly to more than twice the critical value, then decreases abruptly, at a series of cross sections located downstream from the Emma and Midland Avenue Bridges. Median particle-size sediment is mobile at most cross sections in the study reach during the 10-year flood; however, the bed material is immobile at cross sections just upstream from the Upper Bypass and Midland Avenue Bridges. A similar s

Optimizing the Construction of the A1 Collaboration Neutron Detector

NASA Astrophysics Data System (ADS)

Chinn, Edward; A1 Collaboration

2016-09-01

We report on the design and construction of a frame designed to optimize both the time efficiency and construction quality of the large scintillator elements These elements will be assembled to form a neutron detector for use by the A1 Collaboration at the Institute for Nuclear Physics in Mainz, Germany. The design had to provide adequate support for the 20 kg scintillator bars while gluing light guides and photomultiplier tubes to both sides of the bars using optical cement. The optical cement requires approximately 24 hours to dry and 100 bars have to be glued with this apparatus. To address each of these issues, several different prototypes were designed and reviewed. The selected apparatus minimized size to meet space constraints, with reduced material cost and provided the most time-efficient way to build the neutron detector. Once the schematic design was selected, we produced technical drawings in AutoDesk Inventor. Assembled the structure and completed gluing of the first batch of scintillators, in order to verify the performance. This apparatus was successful at producing high quality scintillators which were evaluated using cosmic rays. National Science Foundation Grant No. IIA-1358175.

Structural Behavior of Concrete Beams Reinforced with Basalt Fiber Reinforced Polymer (BFRP) Bars

NASA Astrophysics Data System (ADS)

Ovitigala, Thilan

The main challenge for civil engineers is to provide sustainable, environmentally friendly and financially feasible structures to the society. Finding new materials such as fiber reinforced polymer (FRP) material that can fulfill the above requirements is a must. FRP material was expensive and it was limited to niche markets such as space shuttles and air industry in the 1960s. Over the time, it became cheaper and spread to other industries such as sporting goods in the 1980-1990, and then towards the infrastructure industry. Design and construction guidelines are available for carbon fiber reinforced polymer (CFRP), aramid fiber reinforced polymer (AFRP) and glass fiber reinforced polymer (GFRP) and they are currently used in structural applications. Since FRP is linear elastic brittle material, design guidelines for the steel reinforcement are not valid for FRP materials. Corrosion of steel reinforcement affects the durability of the concrete structures. FRP reinforcement is identified as an alternative to steel reinforcement in corrosive environments. Although basalt fiber reinforced polymer (BFRP) has many advantages over other FRP materials, but limited studies have been done. These studies didn't include larger BFRP bar diameters that are mostly used in practice. Therefore, larger beam sizes with larger BFRP reinforcement bar diameters are needed to investigate the flexural and shear behavior of BFRP reinforced concrete beams. Also, shear behavior of BFRP reinforced concrete beams was not yet studied. Experimental testing of mechanical properties and bond strength of BFRP bars and flexural and shear behavior of BFRP reinforced concrete beams are needed to include BFRP reinforcement bars in the design codes. This study mainly focuses on the use of BFRP bars as internal reinforcement. The test results of the mechanical properties of BFRP reinforcement bars, the bond strength of BFRP reinforcement bars, and the flexural and shear behavior of concrete beams reinforced with BFRP reinforcement bars are presented and verified with other research studies, existing design codes and guidelines provided for other FRP bars. Based on the experimental testing results, analytical equations were developed and existing equations were modified to predict the actual structural behavior of FRP bar reinforced concrete beams with reasonable accuracy.

New insights on the origin of the High Velocity Peaks in the Galactic Bulge

NASA Astrophysics Data System (ADS)

Fernández-Trincado, J. G.; Robin, A. C.; Moreno, E.; Pérez-Villegas, A.; Pichardo, B.

2017-12-01

We provide new insight on the origin of the cold high-V_{los} peaks (˜200 kms^{-1}) in the Milky Way bulge discovered in the APOGEE commissioning data (Nidever et al. 2012). Here we show that such kinematic behaviour present in the field regions towards the Galactic bulge is not likely associated with orbits that build the boxy/peanut (B/P) bulge. To this purpose, a new set of test particle simulations of a kinematically cold stellar disk evolved in a 3D steady-state barred Milky Way galactic potential, has been analysed in detail. Especially bar particles trapped into the bar are identified through the orbital Jacobi energy E_{J}, which allows us to identify the building blocks of the B/P feature and investigate their kinematic properties. Finally, we present preliminary results showing that the high-V_{los} features observed towards the Milky Way bulge are a natural consequence of a large-scale midplane particle structure, which is unlikely associated with the Galactic bar.

Large strain dynamic compression for soft materials using a direct impact experiment

NASA Astrophysics Data System (ADS)

Meenken, T.; Hiermaier, S.

2006-08-01

Measurement of strain rate dependent material data of low density low strength materials like polymeric foams and rubbers still poses challenges of a different kind to the experimental set up. For instance, in conventional Split Hopkinson Pressure Bar tests the impedance mismatch between the bars and the specimen makes strain measurement almost impossible. Application of viscoelastic bars poses new problems with wave dispersion. Also, maximum achievable strains and strain rates depend directly on the bar lengths, resulting in large experimental set ups in order to measure relevant data for automobile crash applications. In this paper a modified SHPB will be presented for testing low impedance materials. High strains can be achieved with nearly constant strain rate. A thin film stress measurement has been applied to the specimen/bar interfaces to investigate the initial sample ring up process. The process of stress homogeneity within the sample was investigated on EPDM and PU rubber.

Effect of a viscoelastic target on the impact response of a flat-nosed projectile

NASA Astrophysics Data System (ADS)

Liu, Hu; Yang, Jialing; Liu, Hua

2018-02-01

Taylor impact is a widely used strategy in which a flat-nosed projectile is fired onto a rigid anvil directly to determine the dynamic strength of rod specimens. Nowadays, the rigid anvil is often replaced by an output target bar to ensure the accuracy of measurement via recording strain signals in the output bar. For testing the dynamic strength of low-density materials, a low-impedance target bar, which exhibits viscoelastic characteristics is often employed. In this paper, an extended Taylor model is proposed to improve the idealization of treating the target bar as perfectly rigid material in the classic Taylor model, and the viscoelastic effect of the target bar is incorporated. The viscoelastic target bar is depicted by two elastic springs and one dashpot. Based on the plastic shock wave theory in the flat-nosed projectile associated with the viscoelastic wave analysis in the target bar, the viscoelastic effect of the target bar on the impact response of the flat-nosed projectile is investigated. The finite element simulation is also carried out to verify the theoretical model, and good agreement is found. The present theoretical model is also called the Taylor-cylinder Hopkinson impact, which provides a more accurate way to identify the dynamic material parameters. The dynamic responses of the present model are further compared with previous elastic and rigid target bar models. It is found that the viscoelastic effect of the target bar should be taken into consideration in the Taylor-cylinder Hopkinson impact test for low-impedance materials.

Experimental Study on Basic Mechanical Properties of BFRP Bars

NASA Astrophysics Data System (ADS)

Fan, Xiaochun; Xu, Ting; Zhou, Zhengrong; Zhou, Xun

2017-10-01

Basalt Fiber Reinforced Polymer (BFRP) bars have the advantages of corrosion resistance, high strength, light weight, good dielectric properties, and they are new type of green reinforced alternative material. In order to determine the mechanical properties of BFRP bars, the tensile strength of basalt fiber bars was necessary to be studied. The diameters of the basalt fiber bars were compared by means of uniaxial tensile test in this article. Then the stress-strain curve can be drawn out. The results show that the stress - strain curve of BFRP bars present straight line relation, and there is no sign before failure; there is no yield platform on the stress-strain curve of BFRP bars, which are typical brittle material;the tensile strength of BFRP bars is about 3 times higher than that of ordinary steel bars. and the elastic modulus is about 1/5 of that of ordinary steel; the ultimate tensile strength of BFRP bars varies little with the increase of diameter, but there exist some differences in modulus values.

Electrofriction method of manufacturing squirrel cage rotors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, John S.

2005-04-12

A method of making a squirrel cage rotor of copper material for use in AC or DC motors, includes forming a core with longitudinal slots, inserting bars of conductive material in the slots, with ends extending out of opposite ends of the core, and joining the end rings to the bars, wherein the conductive material of either the end rings or the bars is copper. Various methods of joining the end rings to the bars are disclosed including electrofriction welding, current pulse welding and brazing, transient liquid phase joining and casting. Pressure is also applied to the end rings tomore » improve contact and reduce areas of small or uneven contact between the bar ends and the end rings. Rotors made with such methods are also disclosed.« less

5. Historic American Buildings Survey, Bill Engdahl for HedrichBlessing, Photographers, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Historic American Buildings Survey, Bill Engdahl for Hedrich-Blessing, Photographers, February, 1979 INTERIOR DOOR WITH BARRED TRANSOM. - Douglas Drug Store, 1201 East Elizabeth Street, Brownsville, Cameron County, TX

Numerical simulations of wave propagation in long bars with application to Kolsky bar testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, Edmundo

2014-11-01

Material testing using the Kolsky bar, or split Hopkinson bar, technique has proven instrumental to conduct measurements of material behavior at strain rates in the order of 10 3 s -1. Test design and data reduction, however, remain empirical endeavors based on the experimentalist's experience. Issues such as wave propagation across discontinuities, the effect of the deformation of the bar surfaces in contact with the specimen, the effect of geometric features in tensile specimens (dog-bone shape), wave dispersion in the bars and other particulars are generally treated using simplified models. The work presented here was conducted in Q3 and Q4more » of FY14. The objective was to demonstrate the feasibility of numerical simulations of Kolsky bar tests, which was done successfully.« less

Dynamic tensile characterization of a 4330 steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-08-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.« less

Dynamic tensile characterization of a 4330-V steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-09-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, Edmundo

The Kolsky compression bar, or split Hopkinson pressure bar (SHPB), is an ex- perimental apparatus used to obtain the stress-strain response of material specimens at strain rates in the order of 10 2 to 10 4 1/s. Its operation and associated data re- duction are based on principles of one-dimensional wave propagation in rods. Second order effects such as indentation of the bars by the specimen and wave dispersion in the bars, however, can significantly affect aspects of the measured material response. Finite element models of the experimental apparatus were used here to demonstrate these two effects. A proceduremore » proposed by Safa and Gary (2010) to account for bar indentation was also evaluated and shown to improve the estimation of the strain in the bars significantly. The use of pulse shapers was also shown to alleviate the effects of wave dispersion. Combining the two can lead to more reliable results in Kolsky compression bar testing.« less

Sensor calibration of polymeric Hopkinson bars for dynamic testing of soft materials

NASA Astrophysics Data System (ADS)

Martarelli, Milena; Mancini, Edoardo; Lonzi, Barbara; Sasso, Marco

2018-02-01

Split Hopkinson pressure bar (SHPB) testing is one of the most common techniques for the estimation of the constitutive behaviour of metallic materials. In this paper, the characterisation of soft rubber-like materials has been addressed by means of polymeric bars thanks to their reduced mechanical impedance. Due to their visco-elastic nature, polymeric bars are more sensitive to temperature changes than metallic bars, and due to their low conductance, the strain gauges used to measure the propagating wave in an SHPB may be exposed to significant heating. Consequently, a calibration procedure has been proposed to estimate quantitatively the temperature influence on strain gauge output. Furthermore, the calibration is used to determine the elastic modulus of the polymeric bars, which is an important parameter for the synchronisation of the propagation waves measured in the input and output bar strain gate stations, and for the correct determination of stress and strain evolution within the specimen. An example of the application has been reported in order to demonstrate the effectiveness of the technique. Different tests at different strain rates have been carried out on samples made of nytrile butadyene rubber (NBR) from the same injection moulding batch. Thanks to the correct synchronisation of the measured propagation waves measured by the strain gauges and applying the calibrated coefficients, the mechanical behaviour of the NBR material is obtained in terms of strain-rate-strain and stress-strain engineering curves.

Blue 450nm high power semiconductor continuous wave laser bars exceeding rollover output power of 80W

NASA Astrophysics Data System (ADS)

König, H.; Lell, A.; Stojetz, B.; Ali, M.; Eichler, C.; Peter, M.; Löffler, A.; Strauss, U.; Baumann, M.; Balck, A.; Malchus, J.; Krause, V.

2018-02-01

Industrial material processing like cutting or welding of metals is rather energy efficient using direct diode or diode pumped solid state lasers. However, many applications cannot be addressed by established infrared laser technology due to fundamental material properties of the workpiece: For example materials like copper or gold have too low absorption in the near infrared wavelength range to be processed efficiently by use of existing high power laser systems. The huge interest to enable high power kW systems with more suitable wavelengths in the blue spectral range triggered the German funded research project 'BLAULAS': Therein the feasibility and capability of CW operating high power laser bars based on the GaN material system was investigated by Osram and Laserline. High performance bars were enabled by defeating fundamental challenges like material quality as well as the chip processes, both of which differ significantly from well-known IR laser bars. The research samples were assembled on actively cooled heat sinks with hard solder technology. For the first time an output power of 98W per bar at 60A drive current was achieved. Conversion efficiency as high as 46% at 50W output power was demonstrated.

Three-dimensional metal-intercalated covalent organic frameworks for near-ambient energy storage

PubMed Central

Gao, Fei; Ding, Zijing; Meng, Sheng

2013-01-01

A new form of nanoporous material, metal intercalated covalent organic framework (MCOF) is proposed and its energy storage property revealed. Employing density functional and thermodynamical analysis, we find that stable, chemically active, porous materials could form by stacking covalent organic framework (COF) layers with metals as a gluing agent. Metal acts as active sites, while its aggregation is suppressed by a binding energy significantly larger than the corresponding cohesive energy of bulk metals. Two important parameters, metal binding and metal-metal separation, are tuned by selecting suitable building blocks and linkers when constructing COF layers. Systematic searches among a variety of elements and organic molecules identify Ca-intercalated COF with diphenylethyne units as optimal material for H2 storage, reaching a striking gravimetric density ~ 5 wt% at near-ambient conditions (300 K, 20 bar), in comparison to < 0.1 wt% for bare COF-1 under the same condition. PMID:23698018

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esa, Mohammad Faris Mohammad; Hassan, Ibrahim Haji; Rahim, Faszly

Magnetic material such as magnetite are known as particles that respond to external magnetic field with their ferromagnetic properties as they are believed contribute to in responding to the geomagnetic field. These particles are used by terrestrial animals such as termites for navigation and orientation. Since our earth react as giant magnetic bar, the magnitude of this magnetic field present by intensity and direction (inclination and direction). The magnetic properties and presence of magnetite in termites Macrotermes gilvus, common mound-building termite were tested. M. gilvus termites was tested with a Vibrating Sample Magnetometer VSM to determine the magnetic properties ofmore » specimen. The crushed body sample was characterized with X-Ray Diffraction XRD to show the existent of magnetic material (magnetite) in the specimens. Results from VSM indicate that M. gilvus has diamagnetism properties. The characterization by XRD shows the existent of magnetic material in our specimen in low concentration.« less

Template-free synthesis of porous carbon from triazine based polymers and their use in iodine adsorption and CO2 capture.

PubMed

Yao, Chan; Li, Guoyan; Wang, Jiku; Xu, Yanhong; Chang, Limin

2018-01-30

A series of novel triazine-containing pore-tunable carbon materials (NT-POP@800-1-6), which was synthesized via pyrolysis of porous organic polymers (POPs) without any templates. NT-POP@800-1-6 possess moderate BET surface areas of 475-736 m 2  g -1 , have permanent porosity and plenty of nitrogen units in the skeletons as effective sorption sites, and display relatively rapid guest uptake of 56-192 wt% in iodine vapour in the first 4 h. In addition, all the samples exhibit the outstanding CO 2 adsorption capacity of 2.83-3.96 mmol g -1 at 273 K and 1.05 bar. Furthermore, NT-POP@800-1-6 show good selectivity ratios of 21.2-36.9 and 3.3-7.5 for CO 2 /N 2 or CH 4 /N 2 , respectively. We believe that our new building block design provides a general strategy for the construction of triazine-containing carbon materials from various extended building blocks, thereby greatly expanding the range of applicable molecules.

Bars, Lines, & Pies: A Graphing Skills Program. Expect the Unexpected with Math[R

ERIC Educational Resources Information Center

Actuarial Foundation, 2013

2013-01-01

"Bars, Lines, & Pies" is a dynamic math program designed to build graphing skills in students, while also showing them the relevance of math in their lives. Developed by The Actuarial Foundation along with Scholastic, the graphing lessons and activities involve engaging, real-world examples about the environment and recycling. In these lessons,…

Preliminary assessment of channel stability and bed-material transport along Hunter Creek, southwestern Oregon

USGS Publications Warehouse

Jones, Krista L.; Wallick, J. Rose; O'Connor, Jim E.; Keith, Mackenzie K.; Mangano, Joseph F.; Risley, John C.

2011-01-01

This preliminary assessment of (1) bed-material transport in the Hunter Creek basin, (2) historical changes in channel condition, and (3) supplementary data needed to inform permitting decisions regarding instream gravel extraction revealed the following: Along the lower 12.4 km (kilometers) of Hunter Creek from its confluence with the Little South Fork Hunter Creek to its mouth, the river has confined and unconfined segments and is predominately alluvial in its lowermost 11 km. This 12.4-km stretch of river can be divided into two geomorphically distinct study reaches based primarily on valley physiography. In the Upper Study Reach (river kilometer [RKM] 12.4-6), the active channel comprises a mixed bed of bedrock, boulders, and smaller grains. The stream is confined in the upper 1.4 km of the reach by a bedrock canyon and in the lower 2.4 km by its valley. In the Lower Study Reach (RKM 6-0), where the area of gravel bars historically was largest, the stream flows over bed material that is predominately alluvial sediments. The channel alternates between confined and unconfined segments. The primary human activities that likely have affected bed-material transport and the extent and area of gravel bars are (1) historical and ongoing aggregate extraction from gravel bars in the study area and (2) timber harvest and associated road construction throughout the basin. These anthropogenic activities likely have varying effects on sediment transport and deposition throughout the study area and over time. Although assessing the relative effects of these anthropogenic activities on sediment dynamics would be challenging, the Hunter Creek basin may serve as a case study for such an assessment because it is mostly free of other alterations to hydrologic and geomorphic processes such as flow regulation, dredging, and other navigation improvements that are common in many Oregon coastal basins. Several datasets are available that may support a more detailed physical assessment of Hunter Creek. The entire study area has been captured in aerial photographs at least once per decade since the 1940s. This temporally rich photograph dataset would support quantitative analyses of changes in channel planform as well as vegetation cover. Light Detection And Ranging (LiDAR) data collected in 2008 would facilitate hydraulic and sediment-transport modeling and characterization of bar elevations throughout most of the study area. Few studies describing channel morphology and sediment transport exist for the Hunter Creek basin. The most detailed study reported channel incision and bank instability as well as the loss of point bars and pools in the lower 3.9 km of Hunter Creek from slightly downstream of its confluence with Yorke Creek to its mouth (EA Engineering, Sci-ence, and Technology, 1998). Repeat channel cross-sections collected from 1994 to 2010 at four bridges indicate that Hunter Creek is dynamic and subject to channel shifting, aggradation, and incision. Despite this dynamism, the channel at three bridge crossings showed little net change in thalweg elevation during this period. However, the channel thalweg aggraded 0.55 m from 2004 to 2008 near the bridge at RKM 3.5. Systematic delineation of gravel bars from aerial photographs collected in 1940, 1965, 2005, and 2009 indicates a 52-percent reduction in the area of bed-material sediment throughout the study area from 1940 to 2009. Net bar loss was greatest in the Lower Study Reach from RKM 1-4 and mainly is associ-ated with the encroachment of vegetation onto upper-bar surfaces lacking apparent vegetation in 1940. Bar-surface material was approximately equal in size to bar-subsurface material at Conn Creek Bar, whereas it was distinctly coarser than the subsurface material at Menasha Bar. Armoring ratios, which indicate the coarseness of the bar surface relative to the bar subsurface, were calculated as 0.97 for Conn Creek Bar and 1.5 for Menasha Bar. These ratios tentatively show that

Design criteria for panic bars and auger miner safety. Panic bar study. Volume 1. Continuous miners. Open file report (final), 1973-74

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marrus, L.D.; Rogne, C.

1974-01-23

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment, including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the ''fire door'' type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, whenmore » emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). (GRA)« less

3. INSIDE BATCH FURNACE BUILDING, VIEW LOOKING NORTH AT REGENERATIVE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. INSIDE BATCH FURNACE BUILDING, VIEW LOOKING NORTH AT REGENERATIVE BATCH FURNACES ON LEFT AND 5 TON CAPACITY CHARGING MACHINE ON RIGHT. - U.S. Steel Duquesne Works, 22-Inch Bar Mill, Along Monongahela River, Duquesne, Allegheny County, PA

Endophilin-A1 BAR domain interaction with arachidonyl CoA.

PubMed

Petoukhov, Maxim V; Weissenhorn, Winfried; Svergun, Dmitri I

2014-01-01

Endophilin-A1 belongs to the family of BAR domain containing proteins that catalyze membrane remodeling processes via sensing, inducing and stabilizing membrane curvature. We show that the BAR domain of endophilin-A1 binds arachidonic acid and molds its coenzyme A (CoA) activated form, arachidonyl-CoA into a defined structure. We studied low resolution structures of endophilin-A1-BAR and its complex with arachidonyl-CoA in solution using synchrotron small-angle X-ray scattering (SAXS). The free endophilin-A1-BAR domain is shown to be dimeric at lower concentrations but builds tetramers and higher order complexes with increasing concentrations. Extensive titration SAXS studies revealed that the BAR domain produces a homogenous complex with the lipid micelles. The structural model of the complexes revealed two arachidonyl-CoA micelles bound to the distal arms of an endophilin-A1-BAR dimer. Intriguingly, the radius of the bound micelles significantly decreases compared to that of the free micelles, and this structural result may provide hints on the potential biological relevance of the endophilin-A1-BAR interaction with arachidonyl CoA.

A Novel Field-Based Approach for Analysing Bar Reworking: Trialled in the Tongariro River, New Zealand

NASA Astrophysics Data System (ADS)

Reid, H. E.; Williams, R. D.; Coleman, S.; Brierley, G. J.

2012-04-01

Bars are key morphological units within river systems, fashioning the sediment regime and bedload transport processes within a reach. Reworking of these features underpins channel adjustment at larger scales, thereby acting as a key determinant of channel stability. Yet, despite their fundamental importance to channel evolution, few investigations have acquired spatially continuous data on bar morphology and sediment particle size to facilitate detailed investigations on bar reworking. To this end, four bars along a 10 km reach of wandering gravel bed river were surveyed, capturing downstream changes in slope, bed material size and channel planform. High resolution surveys of bar topography and grain-size roughness were acquired using Terrestrial Laser Scanning (TLS). The resulting point clouds were then filtered to a quasi-uniform point spacing of 0.05 m and statistical attributes were extracted at a 1 m resolution. The detrended standard deviations from the TLS data were then correlated to the underlying median grain size (D50), which was measured using the Wolman transect method. The resulting linear regression model had a strong relationship (R2 = 0.92) and was used to map median sediment size across each bar. Representative cross-sections were used to interpolate water surfaces across each bar, for flood events with recurrence intervals (RI) of 2.33, 10, 20, 50 and 100 years, enabling flow depth to be calculated. The ratio of dimensionless shear stress (from the depth raster and slope) over critical shear stress (from the D50 raster) was used to map entrainment across each bar at 1 m resolution for each flood event. This is referred to as 'relative erodibility'. The two downstream bars, which are characterised by low slope and smaller bed material, underwent greater entrainment during the more frequent 2.33 RI flood than the higher energy upstream bars which required floods with a RI of 10 or greater. Reworking was also assessed for within-bar geomorphic units. This work demonstrated that floods with a 2.33 year RI flush material on the bar tail, while 10 year RI floods rework the supra-platform and back channel deposits and only the largest flows (RI of > = 50) are able to entrain the bar head materials. Interestingly, despite dramatic differences between slope, grain-size and planform, all bar heads were found to undergo minimal entrainment (between 10 - 20 %) during the frequent 2.33 RI flood. This indicates that resistance at the bar head during frequent floods promotes the deposition of finer-grained, more transient units in their lee. This process-based appraisal explains channel adjustment at the reach-scale, whereby the proportion of the bar made out of more frequently entrained units (tail, backchannel, supra-platform) relative to more static units at the bar head exerts a direct influence upon the extent of adjustment of the bar and the reach as a whole.

Dynamic Deformation Behavior of Soft Material Using Shpb Technique and Pulse Shaper

NASA Astrophysics Data System (ADS)

Lee, Ouk Sub; Cho, Kyu Sang; Kim, Sung Hyun; Han, Yong Hwan

This paper presents a modified Split Hopkinson Pressure Bar (SHPB) technique to obtain compressive stress strain data for NBR rubber materials. An experimental technique with a modified the conventional SHPB has been developed for measuring the compressive stress strain responses of materials with low mechanical impedance and low compressive strengths, such as the rubber and the polymeric material. This paper uses an aluminum pressure bar to achieve a closer impedance match between the pressure bar and the specimen materials. In addition, a pulse shaper is utilized to lengthen the rising time of the incident pulse to ensure dynamic stress equilibrium and homogeneous deformation of NBR rubber materials. It is found that the modified technique can determine the dynamic deformation behavior of rubbers more accurately.

EXTENSION OF SHEAR RUNOUT TABLE INTO SHIPPING BUILDING, WHICH LAY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTENSION OF SHEAR RUNOUT TABLE INTO SHIPPING BUILDING, WHICH LAY PERPENDICULAR TO 8" MILL. VIEW LOOKING NORTH INCLUDES NEW BOLD PRODUCT SHEARS, STOPS LENGTH GAUGES, AND BUNDLING CRADLES. - LTV Steel, 8-inch Bar Mill, Buffalo Plant, Buffalo, Erie County, NY

Glass fiber reinforced polymer bars as top mat reinforcement for bridge decks.

DOT National Transportation Integrated Search

2002-01-01

The objectives of this research were to characterize the material and bond properties of three commercially available GFRP (glass fiber reinforced polymer) reinforcing bars, and evaluate the effects of the material properties and the current ACI desi...

Analysis of temperature measurements at lead(Pb) / transparent window interface under shock compression

NASA Astrophysics Data System (ADS)

Robert, G.; Gillot, F.; Bénier, J.

2014-05-01

In this paper, we show that if the temperature bar TA obtained by a pyrometric measurement on a shock-heated material can be reached with a good precision (~5%), its transformation into a useful temperature bar TT to constrain an equation of state is not straightforward. The effects of interface, in particular the adaptation of impedance, can create a difference between bar TA and bar TT of more than 10%. This impedance correction depends on the shock adiabat of the glue, not known for thin layers of few |am but also of the equation of state of the material and of its lines of phase transition.

Partial entrainment of gravel bars during floods

USGS Publications Warehouse

Konrad, Christopher P.; Booth, Derek B.; Burges, Stephen J.; Montgomery, David R.

2002-01-01

Spatial patterns of bed material entrainment by floods were documented at seven gravel bars using arrays of metal washers (bed tags) placed in the streambed. The observed patterns were used to test a general stochastic model that bed material entrainment is a spatially independent, random process where the probability of entrainment is uniform over a gravel bar and a function of the peak dimensionless shear stress τ0* of the flood. The fraction of tags missing from a gravel bar during a flood, or partial entrainment, had an approximately normal distribution with respect to τ0* with a mean value (50% of the tags entrained) of 0.085 and standard deviation of 0.022 (root‐mean‐square error of 0.09). Variation in partial entrainment for a given τ0* demonstrated the effects of flow conditioning on bed strength, with lower values of partial entrainment after intermediate magnitude floods (0.065 < τ0*< 0.08) than after higher magnitude floods. Although the probability of bed material entrainment was approximately uniform over a gravel bar during individual floods and independent from flood to flood, regions of preferential stability and instability emerged at some bars over the course of a wet season. Deviations from spatially uniform and independent bed material entrainment were most pronounced for reaches with varied flow and in consecutive floods with small to intermediate magnitudes.

The psychomechanics of simulated sound sources: Material properties of impacted bars

NASA Astrophysics Data System (ADS)

McAdams, Stephen; Chaigne, Antoine; Roussarie, Vincent

2004-03-01

Sound can convey information about the materials composing an object that are often not directly available to the visual system. Material and geometric properties of synthesized impacted bars with a tube resonator were varied, their perceptual structure was inferred from multidimensional scaling of dissimilarity judgments, and the psychophysical relations between the two were quantified. Constant cross-section bars varying in mass density and viscoelastic damping coefficient were synthesized with a physical model in experiment 1. A two-dimensional perceptual space resulted, and the dimensions were correlated with the mechanical parameters after applying a power-law transformation. Variable cross-section bars varying in length and viscoelastic damping coefficient were synthesized in experiment 2 with two sets of lengths creating high- and low-pitched bars. In the low-pitched bars, there was a coupling between the bar and the resonator that modified the decay characteristics. Perceptual dimensions again corresponded to the mechanical parameters. A set of potential temporal, spectral, and spectrotemporal correlates of the auditory representation were derived from the signal. The dimensions related to mass density and bar length were correlated with the frequency of the lowest partial and are related to pitch perception. The correlate most likely to represent the viscoelastic damping coefficient across all three stimulus sets is a linear combination of a decay constant derived from the temporal envelope and the spectral center of gravity derived from a cochlear representation of the signal. These results attest to the perceptual salience of energy-loss phenomena in sound source behavior.

Neural network modeling of conditions of destruction of wood plank based on measurements

NASA Astrophysics Data System (ADS)

Filkin, V.; Kaverzneva, T.; Lazovskaya, T.; Lukinskiy, E.; Petrov, A.; Stolyarov, O.; Tarkhov, D.

2016-11-01

The paper deals with the possibility of predicting the ultimate load breaking timber sample based on the loading force dependence on the deflection before destruction. Prediction of mechanical properties of wood is handicapped by complex anisotropic structures. The anisotropic nature of the material and, in a great measure, the random nature of wood grain local features defining moment of destruction lead to a significant dependence of the required load on the individual characteristics of a particular bar. The ultimate load is sought as a function of the coefficients of the neural network approximation of the loading force dependence on the deflection. For this purpose, a number of experiments on timber sample loading until the destruction is conducted. Modeling of the conditions of material destruction may provide the required safety control in building industry.

Modelling, simulation and verification of the screening process of a swing-bar sieve based on the DEM

NASA Astrophysics Data System (ADS)

Wang, Yang; Yu, Jianqun; Yu, Yajun

2018-05-01

To solve the problems in the DEM simulations of the screening process of a swing-bar sieve, in this paper we propose the real-virtual boundary method to build the geometrical model of the screen deck on a swing-bar sieve. The motion of the swing-bar sieve is modelled by the planer multi-body kinematics. A coupled model of the discrete element method (DEM) with multi-body kinematics (MBK) is presented to simulate the flowing and passing processes of soybean particles on the screen deck. By the comparison of the simulated results with the experimental results of the screening process of the LA-LK laboratory scale swing-bar sieve, the feasibility and validity of the real-virtual boundary method and the coupled DEM-MBK model we proposed in this paper can be verified. This work provides the basis for the optimization design of the swing-bar sieve with circular apertures and complex motion.

Preliminary assessment of channel stability and bed-material transport in the Tillamook Bay tributaries and Nehalem River basin, northwestern Oregon

USGS Publications Warehouse

Jones, Krista L.; Keith, Mackenzie K.; O'Connor, Jim E.; Mangano, Joseph F.; Wallick, J. Rose

2012-01-01

This report summarizes a preliminary study of bed-material transport, vertical and lateral channel changes, and existing datasets for the Tillamook (drainage area 156 square kilometers [km2]), Trask (451 km2), Wilson (500 km2), Kilchis (169 km2), Miami (94 km2), and Nehalem (2,207 km2) Rivers along the northwestern Oregon coast. This study, conducted in coopera-tion with the U.S. Army Corps of Engineers and Oregon Department of State Lands to inform permitting decisions regarding instream gravel mining, revealed that: * Study areas along the six rivers can be divided into reaches based on tidal influence and topography. The fluvial (nontidal or dominated by riverine processes) reaches vary in length (2.4-9.3 kilometer [km]), gradient (0.0011-0.0075 meter of elevation change per meter of channel length [m/m]), and bed-material composition (a mixture of alluvium and intermittent bedrock outcrops to predominately alluvium). In fluvial reaches, unit bar area (square meter of bar area per meter of channel length [m2/m]) as mapped from 2009 photographs ranged from 7.1 m2/m on the Tillamook River to 27.9 m2/m on the Miami River. * In tidal reaches, all six rivers flow over alluvial deposits, but have varying gradients (0.0001-0.0013 m/m) and lengths affected by tide (1.3-24.6 km). The Miami River has the steepest and shortest tidal reach and the Nehalem River has the flattest and longest tidal reach. Bars in the tidal reaches are generally composed of sand and mud. Unit bar area was greatest in the Tidal Nehalem Reach, where extensive mud flats flank the lower channel. * Background factors such as valley and channel confinement, basin geology, channel slope, and tidal extent control the spatial variation in the accumulation and texture of bed material. Presently, the Upper Fluvial Wilson and Miami Reaches and Fluvial Nehalem Reach have the greatest abundance of gravel bars, likely owing to local bed-material sources in combination with decreasing channel gradient and valley confinement. * Natural and human-caused disturbances such as mass movements, logging, fire, channel modifications for navigation and flood control, and gravel mining also have varying effects on channel condition, bed-material transport, and distribution and area of bars throughout the study areas and over time. * Existing datasets include at least 16 and 18 sets of aerial and orthophotographs that were taken of the study areas in the Tillamook Bay tributary basins and Nehalem River basin, respectively, from 1939 to 2011. These photographs are available for future assessments of long-term changes in channel condition, bar area, and vegetation establishment patterns. High resolution Light Detection And Ranging (LiDAR) surveys acquired in 2007-2009 could support future quantitative analyses of channel morphology and bed-material transport in all study areas. * A review of deposited and mined gravel volumes reported for instream gravel mining sites shows that bed-material deposition tends to rebuild mined bar surfaces in most years. Mean annual deposition volumes on individual bars exceeded 3,000 cubic meters (m3) on Donaldson Bar on the Wilson River, Dill Bar on the Kilchis River, and Plant and Winslow Bars on the Nehalem River. Cumulative reported volumes of bed-material deposition were greatest at Donaldson and Dill Bars, totaling over 25,000 m3 per site from 2004 to 2011. Within this period, reported cumulative mined volumes were greatest for the Donaldson, Plant, and Winslow Bars, ranging from 24,470 to 33,940 m3. * Analysis of historical stage-streamflow data collected by the U.S. Geological Survey on the Wilson River near Tillamook (14301500) and Nehalem River near Foss (14301000) shows that these rivers have episodically aggraded and incised, mostly following high flow events, but they do not exhibit systematic, long-term trends in bed elevation. * Multiple cross sections show that channels near bridge crossings in all six study areas are dynamic with many subject to incision and aggradation as well as lateral shifts in thalweg position and bank deposition and erosion. * In fluvial reaches, unit bar area declined a net 5.3-83.6 percent from 1939 to 2009. The documented reduction in bar area may be attributable to several factors, including vegetation establishment and stabilization of formerly active bar surfaces, lateral channel changes and resulting alterations in sediment deposition and erosion patterns, and streamflow and/or tide differences between photographs. Other factors that may be associated with the observed reduction in bar area but not assessed in this reconnaissance level study include changes in the sediment and hydrology regimes of these rivers over the analysis period. * In tidal reaches, unit bar area increased on the Tillamook and Nehalem Rivers (98.0 and 14.7 percent, respectively), but declined a net 24.2 to 83.1 percent in the other four tidal reaches. Net increases in bar area in the Tidal Tillamook and Nehalem Reaches were possibly attributable to tidal differences between the photographs as well as sediment deposition behind log booms and pile structures on the Tillamook River between 1939 and 1967. * The armoring ratio (ratio of the median grain sizes of a bar's surface and subsurface layers) was 1.6 at Lower Waldron Bar on the Miami River, tentatively indicating a relative balance between transport capacity and sediment supply at this location. Armoring ratios, however, ranged from 2.4 to 5.5 at sites on the Trask, Wilson, Kilchis, and Nehalem Rivers; these coarse armor layers probably reflect limited bed-material supply at these sites. * On the basis of mapping results, measured armoring ratios, and channel cross section surveys, preliminary conclusions are that the fluvial reaches on the Tillamook, Trask, Kilchis, and Nehalem Rivers are currently sediment supply-limited in terms of bed material - that is, the transport capacity of the channel generally exceeds the supply of bed material. The relation between transport capacity and sediment is more ambiguous for the fluvial reaches on the Wilson and Miami Rivers, but transport-limited conditions are likely for at least parts of these reaches. Some of these reaches have possibly evolved from sediment supply-limited to transport-limited over the last several decades in response to changing basin and climate conditions. * Because of exceedingly low gradients, all the tidal reaches are transport-limited. Bed material in these reaches, however, is primarily sand and finer grain-size material and probably transported as suspended load from upstream reaches. These reaches will be most susceptible to watershed conditions affecting the supply and transport of fine sediment. * Compared to basins on the southwestern Oregon coast, such as the Chetco and Rogue River basins, these six basins likely transport overall less gravel bed material. Although tentative in the absence of actual transport measurements, this conclusion is supported by the much lower area and frequency of bars and longer tidal reaches along all the northcoast rivers examined in this study. * Previous studies suggest that the expansive and largely unvegetated bars visible in the 1939 photographs are primarily associated with voluminous sedimentation starting soon after the first Tillamook Burn fire in 1933. However, USGS studies of temporal bar trends in other Oregon coastal rivers unaffected by the Tillamook Burn show similar declines in bar area over approximately the same analysis period. In the Umpqua and Chetco River basins, historical declines in bar area are associated with long-term decreases in flood magnitude. Other factors may include changes in the type and volume of large wood and riparian vegetation. Further characterization of hydrology patterns in these basins and possible linkages with climate factors related to flood peaks, such as the Pacific Decadal Oscillation, could support inferences of expected future changes in vegetation establishment and channel planform and profile. * More detailed investigations of bed-material transport rates and channel morphology would support assessments of lateral and vertical channel condition and longitudinal trends in bed material. Such assessments would be most practical for the fluvial study areas on the Wilson, Kilchis, Miami, and Nehalem Rivers and relevant to several ongoing management and ecological issues pertaining to sand and gravel transport. Tidal reaches may also be logical subjects for indepth analysis where studies would be more relevant to the deposition and transport of fine sediment (and associated channel and riparian conditions and processes) rather than coarse bed material.

Why Buckling Stellar Bars Weaken in Disk Galaxies

NASA Astrophysics Data System (ADS)

Martinez-Valpuesta, Inma; Shlosman, Isaac

2004-09-01

Young stellar bars in disk galaxies experience a vertical buckling instability that terminates their growth and thickens them, resulting in a characteristic peanut/boxy shape when viewed edge-on. Using N-body simulations of galactic disks embedded in live halos, we have analyzed the bar structure throughout this instability and found that the outer (approximately) third of the bar dissolves completely while the inner part (within the vertical inner Lindblad resonance) becomes less oval. The bar acquires the frequently observed peanut/boxy-shaped isophotes. We also find that the bar buckling is responsible for a mass injection above the plane, which is subsequently trapped by specific three-dimensional families of periodic orbits of particular shapes explaining the observed isophotes, in line with previous work. Using a three-dimensional orbit analysis and surfaces of sections, we infer that the outer part of the bar is dissolved by a rapidly widening stochastic region around its corotation radius-a process related to the bar growth. This leads to a dramatic decrease in the bar size, decrease in the overall bar strength, and a mild increase in its pattern speed but is not expected to lead to a complete bar dissolution. The buckling instability appears primarily responsible for shortening the secular diffusion timescale to a dynamical one when building the boxy isophotes. The sufficiently long timescale of the described evolution, ~1 Gyr, can affect the observed bar fraction in the local universe and at higher redshifts, both through reduced bar strength and the absence of dust offset lanes in the bar.

PCR-free quantitative detection of genetically modified organism from raw materials. An electrochemiluminescence-based bio bar code method.

PubMed

Zhu, Debin; Tang, Yabing; Xing, Da; Chen, Wei R

2008-05-15

A bio bar code assay based on oligonucleotide-modified gold nanoparticles (Au-NPs) provides a PCR-free method for quantitative detection of nucleic acid targets. However, the current bio bar code assay requires lengthy experimental procedures including the preparation and release of bar code DNA probes from the target-nanoparticle complex and immobilization and hybridization of the probes for quantification. Herein, we report a novel PCR-free electrochemiluminescence (ECL)-based bio bar code assay for the quantitative detection of genetically modified organism (GMO) from raw materials. It consists of tris-(2,2'-bipyridyl) ruthenium (TBR)-labeled bar code DNA, nucleic acid hybridization using Au-NPs and biotin-labeled probes, and selective capture of the hybridization complex by streptavidin-coated paramagnetic beads. The detection of target DNA is realized by direct measurement of ECL emission of TBR. It can quantitatively detect target nucleic acids with high speed and sensitivity. This method can be used to quantitatively detect GMO fragments from real GMO products.

A technique for measurement of material damping in metals. [absorption of structural vibration

NASA Technical Reports Server (NTRS)

Heine, J. C.

1976-01-01

The paper outlines the theory, design, and application of an apparatus based on the single beam resonant dwell technique to determine the damping capacity of metallic materials by measuring the response of a structural element to excitation at a modal frequency. In this apparatus, a cantilever beam specimen of a test material is clamped to a bar which is connected at one end to an electromagnetic shaker and at the other to a heavy base. The thickness of the bar at the base end is reduced by two saw cuts to provide a pivot around which the remainder of the bar can rotate when excited by the shaker which is connected to the bar by a rod passing through a hole in the base. The response of the supporting system to shaker excitation is measured with an accelerometer mounted on the bar at the root of the specimen. Specimen response is measured optically with a low-power microscope with a reticle. Specimen loss factor is determined in terms of acceleration at the beam root, beam tip displacement, and the beam natural frequency.

Photoelastic analysis of mandibular full-arch implant-supported fixed dentures made with different bar materials and manufacturing techniques.

PubMed

Zaparolli, Danilo; Peixoto, Raniel Fernandes; Pupim, Denise; Macedo, Ana Paula; Toniollo, Marcelo Bighetti; Mattos, Maria da Glória Chiarello de

2017-12-01

To compare the stress distribution of mandibular full dentures supported with implants according to the bar materials and manufacturing techniques using a qualitative photoelastic analysis. An acrylic master model simulating the mandibular arch was fabricated with four Morse taper implant analogs of 4.5×6mm. Four different bars were manufactured according to different material and techniques: fiber-reinforced resin (G1, Trinia, CAD/CAM), commercially pure titanium (G2, cpTi, CAD/CAM), cobalt‑chromium (G3, Co-Cr, CAD/CAM) and cobalt‑chromium (G4, Co-Cr, conventional cast). Standard clinical and laboratory procedures were used by an experienced dental technician to fabricate 4 mandibular implant-supported dentures. The photoelastic model was created based on the acrylic master model. A load simulation (150N) was performed in total occlusion against the antagonist. Dentures with fiber-reinforced resin bar (G1) exhibited better stress distribution. Dentures with machined Co-Cr bar (G3) exhibited the worst standard of stress distribution, with an overload on the distal part of the posteriors implants, followed by dentures with cast Co-Cr bar (G4) and machined cpTi bar (G2). The fiber-reinforced resin bar exhibited an adequate stress distribution and can serve as a viable alternative for oral rehabilitation with mandibular full dentures supported with implants. Moreover, the use of the G1 group offered advantages including reduced weight and less possible overload to the implants components, leading to the preservation of the support structure. Copyright © 2017 Elsevier B.V. All rights reserved.

Galaxy Zoo: secular evolution of barred galaxies from structural decomposition of multiband images

NASA Astrophysics Data System (ADS)

Kruk, Sandor J.; Lintott, Chris J.; Bamford, Steven P.; Masters, Karen L.; Simmons, Brooke D.; Häußler, Boris; Cardamone, Carolin N.; Hart, Ross E.; Kelvin, Lee; Schawinski, Kevin; Smethurst, Rebecca J.; Vika, Marina

2018-02-01

We present the results of two-component (disc+bar) and three-component (disc+bar+bulge) multiwavelength 2D photometric decompositions of barred galaxies in five Sloan Digital Sky Survey (SDSS) bands (ugriz). This sample of ∼3500 nearby (z < 0.06) galaxies with strong bars selected from the Galaxy Zoo citizen science project is the largest sample of barred galaxies to be studied using photometric decompositions that include a bar component. With detailed structural analysis, we obtain physical quantities such as the bar- and bulge-to-total luminosity ratios, effective radii, Sérsic indices and colours of the individual components. We observe a clear difference in the colours of the components, the discs being bluer than the bars and bulges. An overwhelming fraction of bulge components have Sérsic indices consistent with being pseudo-bulges. By comparing the barred galaxies with a mass-matched and volume-limited sample of unbarred galaxies, we examine the connection between the presence of a large-scale galactic bar and the properties of discs and bulges. We find that the discs of unbarred galaxies are significantly bluer compared to the discs of barred galaxies, while there is no significant difference in the colours of the bulges. We find possible evidence of secular evolution via bars that leads to the build-up of pseudo-bulges and to the quenching of star formation in the discs. We identify a subsample of unbarred galaxies with an inner lens/oval and find that their properties are similar to barred galaxies, consistent with an evolutionary scenario in which bars dissolve into lenses. This scenario deserves further investigation through both theoretical and observational work.

Carbon footprint of construction using industrialised building system

NASA Astrophysics Data System (ADS)

Lim, P. Y.; Yahya, K.; Aminudin, E.; Zakaria, R.; Haron, Z.; Mohamad Zin, R.; Redzuan, A. A. H.

2017-11-01

Industrialised Building System (IBS) is more sustainable to the environment as compared to the conventional construction methods. However, the construction industry in Malaysia has low acceptance towards IBS due to the resistance to change and also lack of awareness towards sustainability development. Therefore, it is important to study the amount carbon footprint produced by IBS during its manufacturing and construction stage, and also the amount of carbon footprint produced by one meter square of gross floor area of IBS construction using Life Cycle Assessment (LCA) to ease future research through the comparison of the carbon footprint of IBS with the conventional building system. As a result, a case study on a residential type of construction in the vicinity of Johor Bahru, Malaysia was carried out to obtain the necessary data and result. From the data analysis, the amount of greenhouse gases (GHG) for a residential type IBS construction based on the raw materials and resources involved to manufacture and construct IBS components is 0.127 tonnes fossil CO2Eq per meter square. Raw material that contributed to the most amount of carbon footprint is Ordinary Portland Cement (OPC), followed by steel bars, autoclaved aerated blocks and diesel. The LCA data acquired will be very useful in implementing IBS in the residential type construction. As a result, the awareness towards sustainable construction using IBS can be improved.

A large surface neutron and photon detector for civil security applications

NASA Astrophysics Data System (ADS)

De Vita, R.; Ambi, F.; Battaglieri, M.; Osipenko, M.; Piombo, D.; Ricco, G.; Ripani, M.; Taiuti, M.

2010-05-01

The security of ports and transportation is of utmost importance for the development of economy and the security of a nation. Among the necessary actions to ensure the security of ports and borders, the inspection of containers is one of the most time consuming and expensive procedures. Potential threats are the illegal traffic of radioactive materials that could be employed for the construction of weapons, as uranium and plutonium. New techniques for the inspections of containers should be fast, allow the detection and identification of dangerous materials, and be non-invasive, to reduce costs and delays. We propose to build a large surface photon and neutron detector based on plastic scintillator to identify the presence of fissile or fertile material inside a container. The detector consists of scintillator bars, wrapped in thin foils of reflecting material containing gadolinium for neutron capture and arranged in planes separated by few-millimeter-thick lead sheets. The total instrumented surface is a few squared meters. Neutrons emitted by fissile materials are identified by gadolinium capture, which results in a high multiplicity gamma flash with total energy of 8 MeV. Photons emitted by the same source are detected via their Compton interaction in the scintillating material. The discrimination between photons and neutrons is achieved by measuring the number of bars of the detector that measured a signal above threshold. The resulting multiplicity is a clear signature of the particle type. First simulations of the detector response with GEANT4 have shown that a detection efficiency of 20-30% for neutrons emitted by fissile materials and a photon/neutron rejection ratio of more than two orders of magnitude can be achieved. Based on these simulations, the sensitivity of the detector to known amounts of plutonium and uranium was estimated. In this contribution, the conceptual design of the detector will be reviewed, the results of the simulations will be presented and the plan of measurements to be performed on a prototype will be discussed.

The Use of Pristine and Intercalated Graphite Fiber Composites as Buss Bars in Lead-Acid Batteries

NASA Technical Reports Server (NTRS)

Opaluch, Amanda M.

2004-01-01

This study was conducted as a part of the Firefly Energy Space Act Agreement project to investigate the possible use of composite materials in lead acid batteries. Specifically, it examined the use of intercalated graphite composites as buss bars. Currently, buss bars of these batteries are made of lead, a material that is problematic for several reasons. Over time, the lead is subject to both corrosion at the positive plate and sulfation at the negative plate, resulting in decreased battery life. In addition, the weight and size of the lead buss bars make for a heavy and cumbersome battery that is undesirable. Functionality and practicality of lead buss bars is adequate at best; consequently, investigation of more efficient composite materials would be advantageous. Practically speaking, graphite composites have a low density that is nearly one fourth that of its lead counterpart. A battery made of less dense materials would be more attractive to the consumer and the producer because it would be light and convenient. More importantly, low weight would be especially beneficial because it would result in greater overall power density of the battery. In addition to power density, use of graphite composite materials can also increase the life of the battery. From a functional standpoint, corrosion and sulfation at the positive and negative plates are major obstacles when considering how to extend battery life. Neither of these reactions are a factor when graphite composites replace lead parts because graphite is chemically non-reactive with the electrolyte within the battery. Without the problem of corrosion or sulfation, battery life expectancy can be almost doubled. The replacement of lead battery parts with composite materials is also more environmentally favorable because of easy disposal of organic materials. For this study, both pristine and bromine intercalated single-ply graphite fiber composites were created. The composites were fabricated in such a way as to facilitate their use in a 3" x 1/2" buss bar test cell. The prime objective of this investigation was to examine the effectiveness of a variety of graphite composite materials to act as buss bars and carry the current to and from the positive and negative battery plates. This energy transfer can be maximized by use of materials with high conductivity to minimize the buss resistance. Electrical conductivity of composites was measured using both a contactless eddy current probe and a four point measurement. In addition, the stability of these materials at battery-use conditions was characterized.

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials.

PubMed

Prabhu, Rajkumar; Whittington, Wilburn R; Patnaik, Sourav S; Mao, Yuxiong; Begonia, Mark T; Williams, Lakiesha N; Liao, Jun; Horstemeyer, M F

2015-05-18

This study offers a combined experimental and finite element (FE) simulation approach for examining the mechanical behavior of soft biomaterials (e.g. brain, liver, tendon, fat, etc.) when exposed to high strain rates. This study utilized a Split-Hopkinson Pressure Bar (SHPB) to generate strain rates of 100-1,500 sec(-1). The SHPB employed a striker bar consisting of a viscoelastic material (polycarbonate). A sample of the biomaterial was obtained shortly postmortem and prepared for SHPB testing. The specimen was interposed between the incident and transmitted bars, and the pneumatic components of the SHPB were activated to drive the striker bar toward the incident bar. The resulting impact generated a compressive stress wave (i.e. incident wave) that traveled through the incident bar. When the compressive stress wave reached the end of the incident bar, a portion continued forward through the sample and transmitted bar (i.e. transmitted wave) while another portion reversed through the incident bar as a tensile wave (i.e. reflected wave). These waves were measured using strain gages mounted on the incident and transmitted bars. The true stress-strain behavior of the sample was determined from equations based on wave propagation and dynamic force equilibrium. The experimental stress-strain response was three dimensional in nature because the specimen bulged. As such, the hydrostatic stress (first invariant) was used to generate the stress-strain response. In order to extract the uniaxial (one-dimensional) mechanical response of the tissue, an iterative coupled optimization was performed using experimental results and Finite Element Analysis (FEA), which contained an Internal State Variable (ISV) material model used for the tissue. The ISV material model used in the FE simulations of the experimental setup was iteratively calibrated (i.e. optimized) to the experimental data such that the experiment and FEA strain gage values and first invariant of stresses were in good agreement.

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

PubMed Central

Prabhu, Rajkumar; Whittington, Wilburn R.; Patnaik, Sourav S.; Mao, Yuxiong; Begonia, Mark T.; Williams, Lakiesha N.; Liao, Jun; Horstemeyer, M. F.

2015-01-01

This study offers a combined experimental and finite element (FE) simulation approach for examining the mechanical behavior of soft biomaterials (e.g. brain, liver, tendon, fat, etc.) when exposed to high strain rates. This study utilized a Split-Hopkinson Pressure Bar (SHPB) to generate strain rates of 100-1,500 sec-1. The SHPB employed a striker bar consisting of a viscoelastic material (polycarbonate). A sample of the biomaterial was obtained shortly postmortem and prepared for SHPB testing. The specimen was interposed between the incident and transmitted bars, and the pneumatic components of the SHPB were activated to drive the striker bar toward the incident bar. The resulting impact generated a compressive stress wave (i.e. incident wave) that traveled through the incident bar. When the compressive stress wave reached the end of the incident bar, a portion continued forward through the sample and transmitted bar (i.e. transmitted wave) while another portion reversed through the incident bar as a tensile wave (i.e. reflected wave). These waves were measured using strain gages mounted on the incident and transmitted bars. The true stress-strain behavior of the sample was determined from equations based on wave propagation and dynamic force equilibrium. The experimental stress-strain response was three dimensional in nature because the specimen bulged. As such, the hydrostatic stress (first invariant) was used to generate the stress-strain response. In order to extract the uniaxial (one-dimensional) mechanical response of the tissue, an iterative coupled optimization was performed using experimental results and Finite Element Analysis (FEA), which contained an Internal State Variable (ISV) material model used for the tissue. The ISV material model used in the FE simulations of the experimental setup was iteratively calibrated (i.e. optimized) to the experimental data such that the experiment and FEA strain gage values and first invariant of stresses were in good agreement. PMID:26067742

Microporous Organic Polymers Based on Hyper-Crosslinked Coal Tar: Preparation and Application for Gas Adsorption.

PubMed

Gao, Hui; Ding, Lei; Bai, Hua; Li, Lei

2017-02-08

Hyper-crosslinked polymers (HCPs) are promising materials for gas capture and storage, but high cost and complicated preparation limit their practical application. In this paper, a new type of HCPs (CTHPs) was synthesized through a one-step mild Friedel-Crafts reaction with low-cost coal tar as the starting material. Chloroform was utilized as both solvent and crosslinker to generate a three-dimensional crosslinked network with abundant micropores. The maximum BET surface area of the prepared CTHPs could reach up to 929 m 2  g -1 . Owing to the high affinity between the heteroatoms on the coal-tar building blocks and the CO 2 molecules, the adsorption capacity of CTHPs towards CO 2 reached up to 14.2 wt % (1.0 bar, 273 K) with a high selectivity (CO 2 /N 2 =32.3). Furthermore, the obtained CTHPs could adsorb 1.27 wt % H 2 at 1.0 bar and 77.3 K, and also showed capacity for the capture of high organic vapors at room temperature. In comparison with other reported porous organic polymers, CTHPs have the advantages of low-cost, easy preparation, and high gas-adsorption performance, making them suitable for mass production and practical use in the future. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, David Robert; Fensin, Saryu Jindal; Dippo, Olivia

Here, we present a study on the spall strength of additive manufactured (AM) Ti-6Al-4V. Samples were obtained from two pieces of selective laser melted (SLM, a powder bed fusion technique) Ti-6Al-4V such that the response to dynamic tensile loading could be investigated as a function of the orientation between the build layers and the loading direction. A sample of wrought bar-stock Ti-6Al-4V was also tested to act as a baseline representing the traditionally manufactured material response. A single-stage light gas-gun was used to launch a thin flyer plate into the samples, generating a region of intense tensile stress on amore » plane normal to the impact direction. The rear free surface velocity time history of each sample was recorded with laser-based velocimetry to allow the spall strength to be calculated. The samples were also soft recovered to enable post-mortem characterization of the spall damage evolution. Results showed that when the tensile load was applied normal to the interfaces between the build layers caused by the SLM fabrication process the spall strength was drastically reduced, dropping to 60% of that of the wrought material. However, when loaded parallel to the AM build layer interfaces the spall strength was found to remain at 95% of the wrought control, suggesting that when loading normal to the AM layer interfaces, void nucleation is facilitated more readily due to weaknesses along these boundaries. Quasi-static testing of the same sample orientations revealed a much lower degree of anisotropy, demonstrating the importance of rate-dependent studies for damage evolution in AM materials.« less

Bottom-up modeling of damage in heterogeneous quasi-brittle solids

NASA Astrophysics Data System (ADS)

Rinaldi, Antonio

2013-03-01

The theoretical modeling of multisite cracking in quasi-brittle materials is a complex damage problem, hard to model with traditional methods of fracture mechanics due to its multiscale nature and to strain localization induced by microcracks interaction. Macroscale "effective" elastic models can be conveniently applied if a suitable Helmholtz free energy function is identified for a given material scenario. Del Piero and Truskinovsky (Continuum Mech Thermodyn 21:141-171, 2009), among other authors, investigated macroscale continuum solutions capable of matching—in a top-down view—the phenomenology of the damage process for quasi-brittle materials regardless of the microstructure. On the contrary, this paper features a physically based solution method that starts from the direct consideration of the microscale properties and, in a bottom-up view, recovers a continuum elastic description. This procedure is illustrated for a simple one-dimensional problem of this type, a bar modeled stretched by an axial displacement, where the bar is modeled as a 2D random lattice of decohesive spring elements of finite strength. The (microscale) data from simulations are used to identify the "exact" (macro-) damage parameter and to build up the (macro-) Helmholtz function for the equivalent elastic model, bridging the macroscale approach by Del Piero and Truskinovsky. The elastic approach, coupled with microstructural knowledge, becomes a more powerful tool to reproduce a broad class of macroscopic material responses by changing the convexity-concavity of the Helmholtz energy. The analysis points out that mean-field statistics are appropriate prior to damage localization but max-field statistics are better suited in the softening regime up to failure, where microstrain fluctuation needs to be incorporated in the continuum model. This observation is of consequence to revise mean-field damage models from literature and to calibrate Nth gradient continuum models.

Cyclic behavior, development, and characteristics of a ductile hybrid fiber-reinforced polymer (DHFRP) for reinforced concrete members

NASA Astrophysics Data System (ADS)

Hampton, Francis Patrick

Reinforced concrete (R/C) structures especially pavements and bridge decks that constitute vital elements of the infrastructure of all industrialized societies are deteriorating prematurely. Structural repair and upgrading of these structural elements have become a more economical option for constructed facilities especially in the United States and Canada. One method of retrofitting concrete structures is the use of advanced materials. Fiber reinforced polymer (FRP) composite materials typically are in the form of fabric sheets or reinforcing bars. While the strength and stiffness of the FRP is high, composites are inherently brittle, with limited or no ductility. Conventional FRP systems cannot currently meet ductility demand, and therefore, may fail in a catastrophic failure mode. The primary goal of this research was to develop an optimized prototype 10-mm diameter DHFRP bar. The behavior of the bar under full load reversals to failure was investigated. However, this bar first needed to be designed and manufactured in the Fibrous Materials Research at Drexel University. Material properties were determined through testing to categorize the strength properties of the DHFRP. Similitude was used to demonstrate the scaling of properties from the original model bars. The four most important properties of the DHFRP bars are sufficient strength and stiffness, significant ductility for plasticity to develop in the R/C section, and sufficient bond strength for the R/C section to develop its full strength. Once these properties were determined the behavior of reinforced concrete members was investigated. This included the testing of prototype-size beams under monotonic loading and model and prototype beam-columns under reverse cyclic loading. These tests confirmed the large ductility exhibited by the DHFRP. Also the energy absorption capacity of the bar was demonstrated by the hysteretic behavior of the beam-columns. Displacement ductility factors in the range of 3--6 were achieved for all concrete elements tested. To study the long-term behavior of DHFRP, the creep-rupture strength of 5-mm bars was tested. This was conducted first on individual bar specimens and is important in the life-cycle design and performance of DHFRP reinforced concrete.

Investigating skin penetration depth and shape following needle-free injection at different pressures: A cadaveric study.

PubMed

Seok, Joon; Oh, Chang Taek; Kwon, Hyun Jung; Kwon, Tae Rin; Choi, Eun Ja; Choi, Sun Young; Mun, Seog Kyun; Han, Seung-Ho; Kim, Beom Joon; Kim, Myeung Nam

2016-08-01

The effectiveness of needle-free injection devices in neocollagenesis for treating extended skin planes is an area of active research. It is anticipated that needle-free injection systems will not only be used to inject vaccines or insulin, but will also greatly aid skin rejuvenation when used to inject aesthetic materials such as hyaluronic acid, botulinum toxin, and placental extracts. There has not been any specific research to date examining how materials penetrate the skin when a needle-free injection device is used. In this study, we investigated how material infiltrates the skin when it is injected into a cadaver using a needle-free device. Using a needle-free injector (INNOJECTOR™; Amore Pacific, Seoul, Korea), 0.2 ml of 5% methylene blue (MB) or latex was injected into cheeks of human cadavers. The device has a nozzle diameter of 100 µm and produces a jet with velocity of 180 m/s. This jet penetrates the skin and delivers medicine intradermally via liquid propelled by compressed gasses. Materials were injected at pressures of 6 or 8.5 bars, and the injection areas were excised after the procedure. The excised areas were observed visually and with a phototrichogram to investigate the size, infiltration depth, and shape of the hole created on the skin. A small part of the area that was excised was magnified and stained with H&E (×40) for histological examination. We characterized the shape, size, and depth of skin infiltration following injection of 5% MB or latex into cadaver cheeks using a needle-free injection device at various pressure settings. Under visual inspection, the injection at 6 bars created semi-circle-shaped hole that penetrated half the depth of the excised tissue, while injection at 8.5 bars created a cylinder-shaped hole that spanned the entire depth of the excised tissue. More specific measurements were collected using phototrichogram imaging. The shape of the injection entry point was consistently spherical regardless of the amount of pressure used. When injecting 5% MB at 6 bars, the depth of infiltration reached 2.323 mm, while that at 8.5 bars reached 8.906 mm. The area of the hole created by the 5% MB injection was 0.797 mm(2) at 6 bars and 0.242 mm(2) at 8.5 bars. Latex injections reached a depth of 3.480 mm at 6 bars and 7.558 mm at 8.5 bars, and the areas were measured at 1.043 mm(2) (6 bars) and 0.355 mm(2) (8.5 bars). Histological examination showed that the injection penetrated as deep as the superficial musculoaponeurotic system at 6 bars and the masseter muscle at 8.5 bars. When injecting material into the skin using a pneumatic needle-free injector, higher-pressure injections result in a hole with smaller area than lower-pressure injections. The depth and shape of skin penetration vary according to the amount of pressure applied. For materials of low density and viscosity, there is a greater difference in penetration depth according to the degree of pressure. Lasers Surg. Med. 48:624-628, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Effect of bar cross-section and female housing material on retention of mandibular implant bar overdentures: A comparative in vitro study.

PubMed

Abdel-Khalek, Elsayed A; Ibrahim, Abdullah M

2017-01-01

The aim of this study is to evaluate the effect of different cross-sections of bar connecting two implants on the retention of mandibular overdentures with Hader clip or lined with heat-cured resilient liner as a housing material. The retentive values after simulated 1.5 years of service were also recorded. Edentulous mandibular acrylic model was constructed with two dummy implants located in the canine region and connected with cast bar assembly. According to bar cross-section and anchoring method, four groups ( n = 10) of identical overdentures were used as Hader bar/clip group (HCG), Hader bar/silicone liner female housing group (HSG), oval bar/silicone liner female housing group (OSG), and round bar/silicone liner female housing group (RSG). Each overdenture sample was subjected to simulated wear up to 2740 manual insertions/separations. The mean retentive forces were measured at the baseline and after every 500 insertions. The data were statistically analyzed using one-way analysis of variance. The present study demonstrated that all bar cross-sections showed a significant difference at the baseline ( P < 0.05), but HSG showed greater initial retention compared to HCG, OSG, and RSG. OSG showed a significant higher retention after 2740 insertions (simulated five insertions/day). Within the limitation of this in vitro study and for a similar period of service, heat-cured silicone female housing for Hader bar could maintain greater retention for two-implant-retained overdentures than provided by conventional plastic clip after 1.5 year. The oval bar recorded reasonable initial retention values and maintained these values for 1.5 years of service.

FIRST FLOOR, A view looking north at the controls for ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FIRST FLOOR, A view looking north at the controls for the Stokes Press along the wall outside Room 136. These controls include a thermometer, timer and pressure switches, and a buss bar used for static electricity control - Department of Energy, Mound Facility, Isolated Building (I Building), One Mound Road, Miamisburg, Montgomery County, OH

Building a Copper Pipe "Xylophone."

ERIC Educational Resources Information Center

Lapp, David R.

2003-01-01

Explains how to use the equation for frequency of vibration of a transversely oscillating bar or pipe with both ends free to vibrate to build a simple and inexpensive xylophone from a 3-meter section of copper pipe. The instrument produces a full major scale and can be used to investigate various musical intervals. (Author/NB)

Novel Arch Bar Fabricated With a Computer-Aided Design and Three-Dimensional Printing: A Feasibility Study.

PubMed

He, Wei; Sun, Yuchun; Tian, Kaiyue; Xie, Xiaoyan; Wang, Xiaoxia; Li, Zili

2015-11-01

The aim of the present study was to evaluate the feasibility of the design and fabrication of a novel arch bar using 3-dimensional printing. Furthermore, the study assessed its use in a preliminary clinical study of intermaxillary fixation. Seven patients who met the inclusion criteria were enrolled in the present study. Plaster dental casts were created of each patient and scanned using cone-beam computed tomography to obtain digital casts. Computer-aided design software was then used to complete the virtual building of the arch bars, which were manufactured using 3-dimensional printing and a cobalt-chrome alloy. The clinical results were observed after the arch bars were fixed to the dentition with steel wires. The arch bar contacted the dentition with a "surface-to-surface" pattern. The utility of these novel arch bars was verified by successfully fitting them to the dental arches of the patients. All the patients achieved their desired occlusion. The results of the present study have illustrated that this digital method is feasible for constructing a novel arch bar, showing promise for clinical use. Copyright © 2015 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Non-classical continuum theory for fluids incorporating internal and Cosserat rotation rates

NASA Astrophysics Data System (ADS)

Surana, K. S.; Joy, A. D.; Reddy, J. N.

2017-11-01

This paper presents a non-classical continuum theory for fluent continua in which the conservation and balance laws are derived by incorporating both internal rotation rates arising from the velocity gradient tensor and the rotation rates of the Cosserats. Specifically, in this non-classical continuum theory we have (1) the usual velocities (\\bar{ ±b {\\varvec{v }}}), (2) the three internal rotation rates ({}_i^t\\bar{ ±b {\\varvec{Θ }}}) about the axes of a fixed triad whose axes are parallel to the x-frame arising from the velocity gradient tensor (\\bar{ ±b {\\varvec{L }}}) that are completely defined by the antisymmetric part of the velocity gradient tensor, and (3) three additional rotation rates ({}_e^t\\bar{ ±b {\\varvec{Θ }}}) about the axes of the same triad located at each material point as additional three unknown degrees of freedom, referred to as Cosserat rotation rates. This gives rise to \\bar{ ±b {\\varvec{v }}} and {}_e^t\\bar{ ±b {\\varvec{Θ }}} as six degrees of freedom at a material point. The internal rotation rates {}_i^t\\bar{ ±b {\\varvec{Θ }}}, often neglected in classical fluid mechanics, exist in all deforming fluent continua as these are due to velocity gradient tensor. When the internal rotation rates {}_i^t\\bar{ ±b {\\varvec{Θ }}} are resisted by deforming fluent continua, conjugate moment tensor arises that together with {}_i^t\\bar{ ±b {\\varvec{Θ }}} may result in energy storage and/or dissipation, which must be considered in the conservation and balance laws. The Cosserat rotation rations {}_e^t\\bar{ ±b {\\varvec{Θ }}} also result in conjugate moment tensor that together with {}_e^t\\bar{ ±b {\\varvec{Θ }}} may also result in energy storage and/or dissipation. The main focus of this paper is a consistent derivation of conservation and balance laws for fluent continua that incorporate the aforementioned physics and associated constitutive theories for thermofluids using the conditions resulting from the entropy inequality. The material coefficients derived in the constitutive theories are clearly defined and discussed.

Advancements in high-power high-brightness laser bars and single emitters for pumping and direct diode application

NASA Astrophysics Data System (ADS)

An, Haiyan; Jiang, Ching-Long J.; Xiong, Yihan; Zhang, Qiang; Inyang, Aloysius; Felder, Jason; Lewin, Alexander; Roff, Robert; Heinemann, Stefan; Schmidt, Berthold; Treusch, Georg

2015-03-01

We have continuously optimized high fill factor bar and packaging design to increase power and efficiency for thin disc laser system pump application. On the other hand, low fill factor bars packaged on the same direct copper bonded (DCB) cooling platform are used to build multi-kilowatt direct diode laser systems. We have also optimized the single emitter designs for fiber laser pump applications. In this paper, we will give an overview of our recent advances in high power high brightness laser bars and single emitters for pumping and direct diode application. We will present 300W bar development results for our next generation thin disk laser pump source. We will also show recent improvements on slow axis beam quality of low fill factor bar and its application on performance improvement of 4-5 kW TruDiode laser system with BPP of 30 mm*mrad from a 600 μm fiber. Performance and reliability results of single emitter for multiemitter fiber laser pump source will be presented as well.

Stress-strain relationship of high-strength steel (HSS) reinforcing bars

NASA Astrophysics Data System (ADS)

Anggraini, Retno; Tavio, Raka, I. Gede Putu; Agustiar

2018-05-01

The introduction of High-Strength Steel (HSS) reinforcing bars in reinforced concrete members has gained much attention in recent years and led to many advantages such as construction timesaving. It is also more economical since it can reduce the amount of reinforcing steel bars used in concrete members which in turn alleviates the congestion of reinforcement. Up to present, the building codes, e.g. American Concrete Institute (ACI) 318M-14 and Standard National Indonesia (SNI) 2847:2013, still restrict the use of higher-strength steel reinforcing bars for concrete design up to Grade 420 MPa due to the possible suspected brittle behavior of concrete members. This paper evaluates the characteristics of stress-strain relationships of HSS bars if they are comparable to the characteristics of those of Grade 420 MPa. To achieve the objective of the study, a series of steel bars from various grades (420, 550, 650, and 700 MPa) was selected. Tensile tests of these steel samples were conducted under displacement-controlled mode to capture the complete stress-strain curves and particularly the post-yield response of the steel bars. The results indicate that all the steel bars tested had the actual yield strengths greater than the corresponding specified values. The stress-strain curves of HSS reinforcing bars (Grade 550, 650, and 700 MPa) performed slightly different characteristics with those of Grade 420 MPa.

Bar Coding the U. S. Government Bill of Lading and the Material Inspection and Receiving Report.

DTIC Science & Technology

1984-12-01

of respondents K because some of the replies did not respond to this question.) TABLE 3-2. DD 250 PROCESSING CAPABILITIES AUTOMiATED - BAR CODE...Proposed minimum data elements (both human readable and bar coded) required and why? (3) Proposed signature requirement changes and why? (4) Proposed

The Bologna Annotation Resource (BAR 3.0): improving protein functional annotation

PubMed Central

Casadio, Rita

2017-01-01

Abstract BAR 3.0 updates our server BAR (Bologna Annotation Resource) for predicting protein structural and functional features from sequence. We increase data volume, query capabilities and information conveyed to the user. The core of BAR 3.0 is a graph-based clustering procedure of UniProtKB sequences, following strict pairwise similarity criteria (sequence identity ≥40% with alignment coverage ≥90%). Each cluster contains the available annotation downloaded from UniProtKB, GO, PFAM and PDB. After statistical validation, GO terms and PFAM domains are cluster-specific and annotate new sequences entering the cluster after satisfying similarity constraints. BAR 3.0 includes 28 869 663 sequences in 1 361 773 clusters, of which 22.2% (22 241 661 sequences) and 47.4% (24 555 055 sequences) have at least one validated GO term and one PFAM domain, respectively. 1.4% of the clusters (36% of all sequences) include PDB structures and the cluster is associated to a hidden Markov model that allows building template-target alignment suitable for structural modeling. Some other 3 399 026 sequences are singletons. BAR 3.0 offers an improved search interface, allowing queries by UniProtKB-accession, Fasta sequence, GO-term, PFAM-domain, organism, PDB and ligand/s. When evaluated on the CAFA2 targets, BAR 3.0 largely outperforms our previous version and scores among state-of-the-art methods. BAR 3.0 is publicly available and accessible at http://bar.biocomp.unibo.it/bar3. PMID:28453653

Improved silicon carbide for advanced heat engines

NASA Technical Reports Server (NTRS)

Whalen, Thomas J.; Mangels, J. A.

1986-01-01

The development of silicon carbide materials of high strength was initiated and components of complex shape and high reliability were formed. The approach was to adapt a beta-SiC powder and binder system to the injection molding process and to develop procedures and process parameters capable of providing a sintered silicon carbide material with improved properties. The initial effort was to characterize the baseline precursor materials, develop mixing and injection molding procedures for fabricating test bars, and characterize the properties of the sintered materials. Parallel studies of various mixing, dewaxing, and sintering procedures were performed in order to distinguish process routes for improving material properties. A total of 276 modulus-of-rupture (MOR) bars of the baseline material was molded, and 122 bars were fully processed to a sinter density of approximately 95 percent. Fluid mixing techniques were developed which significantly reduced flaw size and improved the strength of the material. Initial MOR tests indicated that strength of the fluid-mixed material exceeds the baseline property by more than 33 percent. the baseline property by more than 33 percent.

[Design of an external prosthetic system with a polycentric mechanism].

PubMed

Valentino Orozco, Gerardo Alejandro; Guerrero Beltrán, Leobardo; Obregón Velasco, Dinora; Avalos Fernández, Oscar

2008-01-01

This medical and engineering work explains the process carried out to build a four-barred polycentric knee mechanism using a mechanical actuator for modular prosthetics. Imitation of the knee performance was the main goal, as well as to cover the basic needs of amputated patients with a low production cost. The polycentric knee mechanism was developed in three stages. The first one was the design and building of the four-barred mechanism using materials as stainless steel 304 and aluminum 6,061 which both have high reliability, corrosion resistance and a relatively easy modeling capability. The total mass was of 700 g. Autocad was used for design and effort analysis was done by using ANSYS. At the end of the first stage, it was observed that its density did not allow mass optimization and no assistant actuator was available for the walking movement. In the second stage, mechanism mass estimation was done by using Alumold 400; this material brings lower density than stainless steel keeping strength and fatigue resistance higher than aluminum 6061. The better ergonomic device was built; a mechanical actuator based on a spring was implemented and tested on two female patients, one geriatric and one 16 years old. The third stage will be described in a future publication, the device mass was optimized by using poly-tetra-fluor-ethylene enhanced with carbon and carbon fiber. Also, the mechanical actuator was complemented with reo-magnetic liquid addition and an electronic control. At the end of this research, an external polycentric knee mechanism was developed, by observing movement stages, velocities, ergonomics, shapes, sizes and significant weights of Mexican patients. Effort analysis by finite element was done and it was determined that the mechanism was capable of modifying its center of rotation according to the knee flexion angle making it a polycentric mechanisms. Also, it was tested on two patients, both females, one 16 and one 75 years old.

Tensile strength/yield strength (TS/YS) ratios of high-strength steel (HSS) reinforcing bars

NASA Astrophysics Data System (ADS)

Tavio, Anggraini, Retno; Raka, I. Gede Putu; Agustiar

2018-05-01

The building codes such as American Concrete Institute (ACI) 318M-14 and Standard National Indonesia (SNI) 2847:2013 require that the ratio of tensile strength (TS) and yield strength (YS) should not less than 1.25. The requirement is based on the assumption that a capability of a structural member to develop inelastic rotation capacity is a function of the length of the yield region. This paper reports an investigation on various steel grades, namely Grades 420, 550, 650, and 700 MPa, to examine the impact of different TS/YS ratios if it is less or greater than the required value. Grades 550, 650, and 700 MPa were purposely selected with the intention to examine if these higher grades are still promising to be implemented in special structural systems since they are prohibited by the building codes for longitudinal reinforcement, whereas Grade 420 MPa bars are the maximum limit of yield strength of reinforcing bars that is allowable for longitudinal reinforcement of special structural systems. Tensile tests of these steel samples were conducted under displacement controlled mode to capture the complete stress-strain curves and particularly the post-yield response of the steel bars. From the study, it can be concluded that Grade 420 performed higher TS/YS ratios and they were able to reach up to more than 1.25. However, the High Strength Still (HSS) bars (Grades 550, 600, and 700 MPa) resulted in lower TS/YS ratios (less than 1.25) compared with those of Grade 420 MPa.

Experimental analysis and constitutive modelling of steel of A-IIIN strength class

NASA Astrophysics Data System (ADS)

Kruszka, Leopold; Janiszewski, Jacek

2015-09-01

Fundamentally important is the better understanding of behaviour of new building steels under impact loadings, including plastic deformations. Results of the experimental analysis in wide range of strain rates in compression at room temperature, as well as constitutive modelling for and B500SP structural steels of new A-IIIN Polish strength class, examined dynamically by split Hopkinson pressure bar technique at high strain rates, are presented in table and graphic forms. Dynamic mechanical characteristics of compressive strength for tested building structural steel are determined as well as dynamic mechanical properties of this material are compared with 18G2-b steel of A-II strength class, including effects of the shape of tested specimens, i.e. their slenderness. The paper focuses the attention on those experimental tests, their interpretation, and constitutive semi-empirical modelling of the behaviour of tested steels based on Johnson-Cook's model. Obtained results of analyses presented here are used for designing and numerical simulations of reinforced concrete protective structures.

Dynamic Characterization and Modeling of Potting Materials for Electronics Assemblies

NASA Astrophysics Data System (ADS)

Joshi, Vasant; Lee, Gilbert; Santiago, Jaime

2015-06-01

Prediction of survivability of encapsulated electronic components subject to impact relies on accurate modeling. Both static and dynamic characterization of encapsulation material is needed to generate a robust material model. Current focus is on potting materials to mitigate high rate loading on impact. In this effort, encapsulation scheme consists of layers of polymeric material Sylgard 184 and Triggerbond Epoxy-20-3001. Experiments conducted for characterization of materials include conventional tension and compression tests, Hopkinson bar, dynamic material analyzer (DMA) and a non-conventional accelerometer based resonance tests for obtaining high frequency data. For an ideal material, data can be fitted to Williams-Landel-Ferry (WLF) model. A new temperature-time shift (TTS) macro was written to compare idealized temperature shift factor (WLF model) with experimental incremental shift factors. Deviations can be observed by comparison of experimental data with the model fit to determine the actual material behavior. Similarly, another macro written for obtaining Ogden model parameter from Hopkinson Bar tests indicates deviations from experimental high strain rate data. In this paper, experimental results for different materials used for mitigating impact, and ways to combine data from resonance, DMA and Hopkinson bar together with modeling refinements will be presented.

Preliminary assessment of channel stability and bed-material transport in the Rogue River basin, southwestern Oregon

USGS Publications Warehouse

Jones, Krista L.; O'Connor, Jim E.; Keith, Mackenzie K.; Mangano, Joseph F.; Wallick, J. Rose

2012-01-01

This report summarizes a preliminary assessment of bed-material transport, vertical and lateral channel changes, and existing datasets for the Rogue River basin, which encompasses 13,390 square kilometers (km2) along the southwestern Oregon coast. This study, conducted to inform permitting decisions regarding instream gravel mining, revealed that: * The Rogue River in its lowermost 178.5 kilometers (km) alternates between confined and unconfined segments, and is predominately alluvial along its lowermost 44 km. The study area on the mainstem Rogue River can be divided into five reaches based on topography, hydrology, and tidal influence. The largely confined, active channel flows over bedrock and coarse bed material composed chiefly of boulders and cobbles in the Grants Pass (river kilometers [RKM] 178.5-152.8), Merlin (RKM 152.8-132.7), and Galice Reaches (RKM 132.7-43.9). Within these confined reaches, the channel contains few bars and has stable planforms except for locally wider segments such as the Brushy Chutes area in the Merlin Reach. Conversely, the active channel flows over predominately alluvial material and contains nearly continuous gravel bars in the Lobster Creek Reach (RKM 43.9-6.7). The channel in the Tidal Reach (RKM 6.7-0) is also alluvial, but tidally affected and unconfined until RKM 2. The Lobster Creek and Tidal Reaches contain some of the most extensive bar deposits within the Rogue River study area. * For the 56.6-km-long segment of the Applegate River included in this study, the river was divided into two reaches based on topography. In the Upper Applegate River Reach (RKM 56.6-41.6), the confined, active channel flows over alluvium and bedrock and has few bars. In the Lower Applegate River Reach (RKM 41.6-0), the active channel alternates between confined and unconfined segments, flows predominantly over alluvium, shifts laterally in unconfined sections, and contains more numerous and larger bars. * The 6.5-km segment of the lower Illinois River included in this study was treated as one reach. This stretch of the Illinois River is fully alluvial, with nearly continuous gravel bars flanking the channel. The width of the active channel is confined by the narrow topography of the valley. * The primary human activities that have likely influenced channel condition, bed-material transport, and the extent and area of bars are (1) historical gold mining throughout the basin, (2) historical and ongoing gravel mining from instream sites in the Tidal Reach and floodplain sites such as those in the Lower Applegate River Reach, (3) hydropower and flow control structures, (4) forest management and fires throughout the basin, and (5) dredging. These anthropogenic activities likely have varying effects on channel condition and the transport and deposition of sediment throughout the study area and over time. * Several vertical (aspect) aerial photographs (including the complete coverages of the study area taken in 1995, 2000, 2005, and 2009 and the partial coverages taken in 1967, 1968, 1969, and 1990) are available for assessing long-term changes in attributes such as channel condition, bar area, and vegetation cover. A Light Detection And Ranging (LiDAR) survey performed in 2007-2008 provides 1-m resolution topographic data for sections of the Grants Pass (RKM 178.5-167.6) and Lobster Creek (RKM 17.8-12 and 10-6.7) Reaches and the entire Tidal Reach. * Previous studies provide information for specific locations, including (1) an estimated average annual bed-material load of 76,000 m3 at the former Savage Rapids Dam site (RKM 173.1, Grants Pass Reach), (2) over 490 m of channel shifting from 1965 to 1991 in the Brushy Chutes area (RKM 142-141, Merlin Reach), (3) active sediment transport and channel processes in the Lobster Creek Reach, (4) lateral channel migration in the Tidal Reach, and (5) up to 1.8 m of bar aggradation from the town of Agness (RKM 45.1) to the Rogue River mouth following the flood in water year 1997. * Review of the repeat surveys conducted at the instream gravel-mining sites on Elephant and Wedderburn Bars tentatively indicated that these bars (1) experience some bed-material deposition in most years and more substantial deposition following high flows such as those in water years 1997 and 2006, and (2) are dynamic and subject to local scour and deposition. * Results from the specific gage analyses completed for five long-term USGS streamflow-gaging stations showed that only the Grants Pass station on the Rogue River (RKM 164.4, Grants Pass Reach) experienced substantial changes in the stage-discharge relationship across a range of flows from 1938 to 2009. Observed changes indicate channel incision at this site. * The Rogue and Applegate Rivers are dynamic and subject to channel shifting, aggradation, and incision, as indicated by channel cross sections surveyed during 2000-2010 on the Rogue River and 1933-2010 on the Applegate River. The elevation of the riverbed changed substantially (defined here as more than a net 0.5 m of incision or aggradation) at three locations on the Rogue River (near RKM 164.5, 139.2, and 1.3) and two on the Applegate River (near RKM 42 and 13.5). * Systematic delineation of bar features from vertical photographs taken in 1967-69, 2005, and 2009 indicated that most of the repeat mapping sites had a net loss in bar area over the analysis period, ranging from 22 percent at the Oak Flat site (Illinois River Reach) to 69 percent at the Thompson Creek site (Upper Applegate River Reach). Bar area remained stable at the Williams Creek site (Lower Applegate River Reach), but increased 11 percent at the Elephant Rock site (Tidal Reach). The declines in bar area were associated primarily with the establishment of vegetation on upper bar surfaces lacking obvious vegetation in the 1960s. Some of the apparent changes in bar area may also owe to some differences in streamflow and tide levels between the vertical photographs. * On the mainstem Rogue River, the median diameter of surface particles varied from 21 mm at the Wedderburn Bar in the Tidal Reach to more than 100 millimeters (mm) at some of the coarsest bars in the Galice Reach. Low armoring ratios tentatively indicated that sediment supply likely exceeds transport capacity at Orchard (Lobster Creek Reach) and Wedderburn (Tidal Reach) Bars. Conversely, relatively higher armoring ratios indicated that transport capacity likely is in balance with sediment supply at Roberston Bridge Bar (Merlin Reach) and exceeds sediment supply at Rogue River City (Grants Pass Reach), Solitude Riffle (Galice Reach), and Hooks Gulch (Galice Reach) Bars. * Limited particle data were collected in the study areas on the Applegate and Illinois Rivers. Particle size measurements and armoring ratios tentatively show that sediment supply likely exceeds transport capacity at Bakery Bar in the Lower Applegate Reach. Also, the bed material exiting the Applegate River is likely finer than the bed material in the Rogue River, whereas bed material exiting the Illinois River is likely coarser than the bed material in the Rogue River. * Together, these observations and findings indicate that (1) the size, area, and overall position of bars in the Rogue River study area are determined largely by valley physiography, such that unconfined alluvial sections have large channel-flanking bars, whereas confined sections have fewer and smaller bars, (2) segments within the Grants Pass, Merlin, Tidal, Upper Applegate River, and Lower Applegate River Reaches are prone to vertical and/or lateral channel adjustments, and (3) the balance between transport capacity and sediment supply varies throughout the study area. * High winter flows and the steep, confined character of much of the Rogue River within the study area result in a river corridor with a high capacity to transport bed material. In the Grants Pass and Galice Reaches, the extensive in-channel bedrock as well as the sparse number and coarse texture of bars indicate that these reaches are likely supply-limited, meaning that the river's transport capacity exceeds the supply of bed material. In contrast, the Lobster Creek and Tidal Reaches and perhaps portions of the Merlin Reach receive bed-material inputs that more closely balance or even exceed the river's transport capacity. * The lowermost reaches on the Illinois and Applegate Rivers are fully alluvial segments that are likely transport limited, meaning sediment supply likely exceeds the river's transport capacity. However, the steeper Upper Applegate River Reach is likely supply-limited as indicated by the sparse number and area of bars mapped in this reach and the intermittent bedrock outcrops in the channel. The sediment loads derived from these large tributaries draining the Klamath Mountains are probably important contributions to the overall transport of bed material in the Rogue River basin. * Compared to the slightly smaller Umpqua River basin (drainage area 12,103 km2) to the north, the Rogue River (13,390 km2) likely transports more bed material. Although this conclusion of greater bed-material transport in the Rogue River is tentative in the absence of either actual transport measurements or transport capacity calculations, empirical evidence, including the much greater area and frequency of bars along most of the Rogue River as well as the much shorter tidal reach on the Rogue River (6.7 km) compared to the Umpqua River (40 km) supports this inference. * More detailed investigations of bed-material transport rates and channel morphology would support assessments of channel condition, longitudinal trends in particle size, the relation between sediment supply and transport capacity, and the potential causes of bar area loss (such as vegetation establishment and potential changes in peak flow patterns). The reaches most practical for such assessments and relevant to several management and ecological issues are (1) the lower Rogue River basin, including the Lobster Creek and Tidal Reaches of the Rogue River as well as the Illinois River Reach and (2) the Lower Applegate River Reach.

Ten Important Words Plus: A Strategy for Building Word Knowledge

ERIC Educational Resources Information Center

Yopp, Ruth Helen; Yopp, Hallie Kay

2007-01-01

In this strategy, students individually select and record 10 important words on self-adhesive notes as they read a text. Then students build a group bar graph displaying their choices, write a sentence that summarizes the content, and then respond to prompts that ask them to think about words in powerful ways. Several prompts are suggested, each…

Applying object-oriented software engineering at the BaBar collaboration

NASA Astrophysics Data System (ADS)

Jacobsen, Bob; BaBar Collaboration Reconstruction Software Group

1997-02-01

The BaBar experiment at SLAC will start taking data in 1999. We are attempting to build its reconstruction software using good software engineering practices, including the use of object-oriented technology. We summarize our experience to date with analysis and design activities, training, CASE and documentation tools, C++ programming practice and similar topics. The emphasis is on the practical issues of simultaneously introducing new techniques to a large collaboration while under a deadline for system delivery.

Using the split Hopkinson pressure bar to validate material models.

PubMed

Church, Philip; Cornish, Rory; Cullis, Ian; Gould, Peter; Lewtas, Ian

2014-08-28

This paper gives a discussion of the use of the split-Hopkinson bar with particular reference to the requirements of materials modelling at QinetiQ. This is to deploy validated material models for numerical simulations that are physically based and have as little characterization overhead as possible. In order to have confidence that the models have a wide range of applicability, this means, at most, characterizing the models at low rate and then validating them at high rate. The split Hopkinson pressure bar (SHPB) is ideal for this purpose. It is also a very useful tool for analysing material behaviour under non-shock wave loading. This means understanding the output of the test and developing techniques for reliable comparison of simulations with SHPB data. For materials other than metals comparison with an output stress v strain curve is not sufficient as the assumptions built into the classical analysis are generally violated. The method described in this paper compares the simulations with as much validation data as can be derived from deployed instrumentation including the raw strain gauge data on the input and output bars, which avoids any assumptions about stress equilibrium. One has to take into account Pochhammer-Chree oscillations and their effect on the specimen and recognize that this is itself also a valuable validation test of the material model. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Implementation of the P barANDA Planar-GEM tracking detector in Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Divani Veis, Nazila; Ehret, Andre; Firoozabadi, Mohammad M.; Karabowicz, Radoslaw; Maas, Frank; Saito, Nami; Saito, Takehiko R.; Voss, Bernd; PANDA Gem-Tracker Subgroup

2018-02-01

The P barANDA experiment at FAIR will be performed to investigate different aspects of hadron physics using anti-proton beams interacting with a fixed nuclear target. The experimental setup consists of a complex series of detector components covering a large solid angle. A detector with a gaseous active media equipped with gas electron multiplier (GEM) technique will be employed to measure tracks of charged particles at forward direction in order to achieve a high momentum resolution. In this work, a full setup of the GEM tracking detector has been implemented in the P barANDA Monte Carlo simulation package (PandaRoot) based on the current technical and conceptual design, and the expected performance of the P barANDA GEM-tracking detector has been investigated. Furthermore, material-budget studies in terms of the radiation length of the P barANDA GEM-tracking detector have been made in order to investigate the effect of the detector materials and its associated structures to particle measurements.

The effects of solution treatment on the mechanical properties of age-hardened A-286 bar stock at elevated and cryogenic temperature

NASA Technical Reports Server (NTRS)

Montano, J. W.

1972-01-01

The mechanical properties are presented of solution treated and age hardened A-286 corrosion resistant steel bar stock. Material solution treated at 899 C or 982 C, each followed by an age hardening treatment of 718 C, was evaluated. Test specimens manufactured from 1.50 inch (3.81 cm) diameter bar stock were tested at temperatures from +649 C to -253 C. The test data indicated excellent tensile, yield, elongation and reduction-in-area properties at all testing temperatures for both solution treated and aged materials. Cryogenic temperature notched tensile, impact, and shear tests indicated excellent notch strength, ductility, and shear values. There was very little difference in the mechanical properties of the two solution treated and aged materials. The only exception was that the 962 C solution treated and aged material had superior stress rupture properties at 649 C.

Reading Through Paint

NASA Technical Reports Server (NTRS)

2004-01-01

Two-dimensional data matrix symbols, which contain encoded letters and numbers, are permanently etched on items for identification. They can store up to 100 times more information than traditional bar codes. While the symbols provide several advantages over bar codes, once they are covered by paint they can no longer be read by optical scanners. Since most products are painted eventually, this presents a problem for industries relying on the symbols for identification and tracking. In 1987, NASA s Marshall Space Flight Center began studying direct parts marking with matrix symbols in order to track millions of Space Shuttle parts. Advances in the technology proved that by incorporating magnetic properties into the paints, inks, and pastes used to apply the matrix symbols, the codes could be read by a magnetic scanner even after being covered with paint or other coatings. NASA received a patent for such a scanner in 1998, but the system it used for development was not portable and was too costly. A prototype was needed as a lead-in to a production model. In the summer of 2000, NASA began seeking companies to build a hand-held scanner that would detect the Read Through Paint data matrix identification marks containing magnetic materials through coatings.

The Bologna Annotation Resource (BAR 3.0): improving protein functional annotation.

PubMed

Profiti, Giuseppe; Martelli, Pier Luigi; Casadio, Rita

2017-07-03

BAR 3.0 updates our server BAR (Bologna Annotation Resource) for predicting protein structural and functional features from sequence. We increase data volume, query capabilities and information conveyed to the user. The core of BAR 3.0 is a graph-based clustering procedure of UniProtKB sequences, following strict pairwise similarity criteria (sequence identity ≥40% with alignment coverage ≥90%). Each cluster contains the available annotation downloaded from UniProtKB, GO, PFAM and PDB. After statistical validation, GO terms and PFAM domains are cluster-specific and annotate new sequences entering the cluster after satisfying similarity constraints. BAR 3.0 includes 28 869 663 sequences in 1 361 773 clusters, of which 22.2% (22 241 661 sequences) and 47.4% (24 555 055 sequences) have at least one validated GO term and one PFAM domain, respectively. 1.4% of the clusters (36% of all sequences) include PDB structures and the cluster is associated to a hidden Markov model that allows building template-target alignment suitable for structural modeling. Some other 3 399 026 sequences are singletons. BAR 3.0 offers an improved search interface, allowing queries by UniProtKB-accession, Fasta sequence, GO-term, PFAM-domain, organism, PDB and ligand/s. When evaluated on the CAFA2 targets, BAR 3.0 largely outperforms our previous version and scores among state-of-the-art methods. BAR 3.0 is publicly available and accessible at http://bar.biocomp.unibo.it/bar3. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Spall fracture in additive manufactured Ti-6Al-4V

DOE PAGES

Jones, David Robert; Fensin, Saryu Jindal; Dippo, Olivia; ...

2016-10-07

Here, we present a study on the spall strength of additive manufactured (AM) Ti-6Al-4V. Samples were obtained from two pieces of selective laser melted (SLM, a powder bed fusion technique) Ti-6Al-4V such that the response to dynamic tensile loading could be investigated as a function of the orientation between the build layers and the loading direction. A sample of wrought bar-stock Ti-6Al-4V was also tested to act as a baseline representing the traditionally manufactured material response. A single-stage light gas-gun was used to launch a thin flyer plate into the samples, generating a region of intense tensile stress on amore » plane normal to the impact direction. The rear free surface velocity time history of each sample was recorded with laser-based velocimetry to allow the spall strength to be calculated. The samples were also soft recovered to enable post-mortem characterization of the spall damage evolution. Results showed that when the tensile load was applied normal to the interfaces between the build layers caused by the SLM fabrication process the spall strength was drastically reduced, dropping to 60% of that of the wrought material. However, when loaded parallel to the AM build layer interfaces the spall strength was found to remain at 95% of the wrought control, suggesting that when loading normal to the AM layer interfaces, void nucleation is facilitated more readily due to weaknesses along these boundaries. Quasi-static testing of the same sample orientations revealed a much lower degree of anisotropy, demonstrating the importance of rate-dependent studies for damage evolution in AM materials.« less

Spall fracture in additive manufactured Ti-6Al-4V

NASA Astrophysics Data System (ADS)

Jones, D. R.; Fensin, S. J.; Dippo, O.; Beal, R. A.; Livescu, V.; Martinez, D. T.; Trujillo, C. P.; Florando, J. N.; Kumar, M.; Gray, G. T.

2016-10-01

We present a study on the spall strength of additive manufactured (AM) Ti-6Al-4V. Samples were obtained from two pieces of selective laser melted (SLM, a powder bed fusion technique) Ti-6Al-4V such that the response to dynamic tensile loading could be investigated as a function of the orientation between the build layers and the loading direction. A sample of wrought bar-stock Ti-6Al-4V was also tested to act as a baseline representing the traditionally manufactured material response. A single-stage light gas-gun was used to launch a thin flyer plate into the samples, generating a region of intense tensile stress on a plane normal to the impact direction. The rear free surface velocity time history of each sample was recorded with laser-based velocimetry to allow the spall strength to be calculated. The samples were also soft recovered to enable post-mortem characterization of the spall damage evolution. Results showed that when the tensile load was applied normal to the interfaces between the build layers caused by the SLM fabrication process the spall strength was drastically reduced, dropping to 60% of that of the wrought material. However, when loaded parallel to the AM build layer interfaces the spall strength was found to remain at 95% of the wrought control, suggesting that when loading normal to the AM layer interfaces, void nucleation is facilitated more readily due to weaknesses along these boundaries. Quasi-static testing of the same sample orientations revealed a much lower degree of anisotropy, demonstrating the importance of rate-dependent studies for damage evolution in AM materials.

[Amaranth bars enriched with fructans: acceptability and nutritional value].

PubMed

Dias Capriles, Vanessa; Gomes Arêas, José Alfredo

2010-09-01

There is an increasing appeal for convenience foods with potential health benefits to the consumer. Raw materials with high nutritional value and functional properties must be used on the development of these food products. Amaranth is a gluten-free grain with high nutrition value. Inulin and oligofructose are prebiotic ingredients presenting effects as the enhancement of calcium absorption. Amaranth bars enriched with inulin and oligofructose were developed in the flavors: banana, Brazilian nuts and dried grape, coconut, peach, strawberry and wall nut. The proximate composition were determined and compared to commercial cereal bars, available in traditional (n=59), light (n=60), diet (n=8), with soy (n=10) and quinoa (n=1) categories. Amaranth bars present mean global acceptance values from 6.3 to 7.6 on a 9-point hedonic scale, nutritional advantages as compared to commercial cereal bars (caloric reduction and higher levels of dietary fiber). Although amaranth is an unknown raw material in Brazil, it shows good potential to be used in the manufacturing of ready-to-eat products. As they are gluten free, these amaranth bars are also an alternative product for celiacs, also contributing to the enhancement of calcium absorption, a problem frequently observed in these patients.

Gram-scale, high-yield synthesis of a robust metal-organic framework for storing methane and other gases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilmer, CE; Farha, OK; Yildirim, T

We have synthesized and characterized a new metal-organic framework (MOF) material, NU-125, that, in the single-crystal limit, achieves a methane storage density at 58 bar (840 psi) and 298 K corresponding to 86% of that obtained with compressed natural gas tanks (CNG) used in vehicles today, when the latter are pressurized to 248 bar (3600 psi). More importantly, the deliverable capacity (58 bar to 5.8 bar) for NU-125 is 67% of the deliverable capacity of a CNG tank that starts at 248 bar. (For crystalline granules or powders, particle packing inefficiencies will yield densities and deliverable capacities lower than 86%more » and 67% of high-pressure CNG.) This material was synthesized in high yield on a gram-scale in a single-batch synthesis. Methane adsorption isotherms were measured over a wide pressure range (0.1-58 bar) and repeated over twelve cycles on the same sample, which showed no detectable degradation. Adsorption of CO2 and H-2 over a broad range of pressures and temperatures are also reported and agree with our computational findings.« less

The transient divided bar method for laboratory measurements of thermal properties

NASA Astrophysics Data System (ADS)

Bording, Thue S.; Nielsen, Søren B.; Balling, Niels

2016-12-01

Accurate information on thermal conductivity and thermal diffusivity of materials is of central importance in relation to geoscience and engineering problems involving the transfer of heat. Several methods, including the classical divided bar technique, are available for laboratory measurements of thermal conductivity, but much fewer for thermal diffusivity. We have generalized the divided bar technique to the transient case in which thermal conductivity, volumetric heat capacity and thereby also thermal diffusivity are measured simultaneously. As the density of samples is easily determined independently, specific heat capacity can also be determined. The finite element formulation provides a flexible forward solution for heat transfer across the bar, and thermal properties are estimated by inverse Monte Carlo modelling. This methodology enables a proper quantification of experimental uncertainties on measured thermal properties and information on their origin. The developed methodology was applied to various materials, including a standard ceramic material and different rock samples, and measuring results were compared with results applying traditional steady-state divided bar and an independent line-source method. All measurements show highly consistent results and with excellent reproducibility and high accuracy. For conductivity the obtained uncertainty is typically 1-3 per cent, and for diffusivity uncertainty may be reduced to about 3-5 per cent. The main uncertainty originates from the presence of thermal contact resistance associated with the internal interfaces in the bar. These are not resolved during inversion and it is imperative that they are minimized. The proposed procedure is simple and may quite easily be implemented to the many steady-state divided bar systems in operation. A thermally controlled bath, as applied here, may not be needed. Simpler systems, such as applying temperature-controlled water directly from a tap, may also be applied.

Pre-stressed thermal protection systems

NASA Technical Reports Server (NTRS)

Dunn, T. J. (Inventor)

1984-01-01

A hexagonal protective and high temperature resistant system for the Space Shuttle Orbiter consists of a multiplicity of pockets formed by hexagonally oriented spacer bars secured on the vehicle substructure. A packing of low density insulating batt material 18 in each pocket, and a thin protective panel of laterally resilient advanced carbon-carbon material surmounting the peripherals bars and packing. Each panel has three stepped or offset lips on contiguous edges. At the center of each pocket is a fully insulated stanchion secured to and connecting the substructure and panel for flexing the panel toward the substructure and thereby prestressing the panel and forcing the panel edges firmly against the spacer bars.

Energy balance and assessment of the pressure build-up around a bolt fastener due to sparking during a lightning impact

NASA Astrophysics Data System (ADS)

Teulet, Philippe; Billoux, Tommy; Cressault, Yann; Masquère, Mathieu; Gleizes, Alain; Revel, Ivan; Lepetit, Bruno; Peres, Gilles

2017-03-01

This work is devoted to the calculation of the energy balance associated with the formation of an electric arc between the bolt shank and an inner structural part of the fuselage during a lightning strike. Assessment of the pressure build-up in the confined volume around the bolt fastener has also been performed. This pressure rise comes from the temperature increase and from the mass density increase (melting and vaporisation of materials). Previous electrical measurements performed by Airbus Group during a lightning test campaign have been used to calculate the total available electrical energy. The energies necessary for melting and vaporisation of bolt and rib are derived from thermodynamic properties of aluminium and titanium. A numerical code has been developed to determine the chemical composition (under the local thermodynamic equilibrium [LTE] assumption) and the internal energy of the plasma for air-Al/Ti mixtures. Plasma and material radiation losses and heat conduction losses have also been evaluated. Finally, an analytical model has been implemented to determine the overpressure as a function of the deposited electrical energy, the energy involved in the arc formation, the energy necessary for melting and the plasma composition and mass density. With this approach, maximum pressure values are in the range 200-330 bars.

Improved Kolsky tension bar for high-rate tensile characterization of materials

NASA Astrophysics Data System (ADS)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin; Korellis, John; Lu, Wei-Yang

2011-04-01

A new Kolsky tension bar has been re-designed and developed at Sandia National Laboratories, CA. The new design uses the concept that a solid striker is fired to impact an end cap attached to the open end of the gun barrel to generate dynamic tensile loading. The gun barrel here serves as part of the loading device. The incident bar that is connected to the gun barrel and the transmission bar follow the design similar to the Kolsky compression bar. The bar supporting and aligning systems are the same as those in the Kolsky compression bar design described by Song et al (2009 Meas. Sci. Technol. 20 115701). Due to the connection complication among the gun barrel, bars and specimen, stress-wave propagation in the new Kolsky tension bar system is comprehensively analyzed. Based on the stress-wave analysis, the strain gage location on the incident bar needs to be carefully determined. A highly precise laser-beam measurement system is recommended to directly measure the displacement of the incident bar end. Dynamic tensile characterization of a 4330-V steel using this new Kolsky tension bar is presented as an example.

Technology Solutions for New Homes Case Study: Columbia County Habitat for Humanity Passive Townhomes

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-04-01

The Columbia County (New York) Habitat for Humanity (Columbia County Habitat) affiliate has been experimenting with high-performance building since 2012, starting with ENERGY STAR® Certified Homes. In 2013, they constructed their first homes aimed at the Passive House standards. Building off of this effort, in 2014 they began work on a second set of Passive Townhomes in Hudson, New York, in partnership with the Advanced Residential Integrated Energy Solutions (ARIES) Building America team and BarlisWedlick Architects.

Assessing patterns of bed-material storage and flux on a mixed bedrock-alluvium river: Umpqua River Oregon, USA

NASA Astrophysics Data System (ADS)

Wallick, R.; Anderson, S.; Keith, M.; Cannon, C.; O'Connor, J. E.

2010-12-01

Gravel bed rivers in the Pacific Northwest and elsewhere provide an important source of commercial aggregate. Mining in-stream gravel, however, can alter channel and bar morphology, resulting in habitat degradation for aquatic species. In order to sustainably manage rivers subject to in-stream gravel extraction, regulatory agencies in Oregon have requested that the USGS complete a series of comprehensive geomorphic and sediment transport studies to provide context for regulatory-agency management of in-stream gravel extraction in Oregon streams. The Umpqua River in western Oregon poses special challenges to this type of assessment. Whereas most rivers subject to gravel extraction are relatively rich in bed-material sediment, the Umpqua River is a mixed bedrock-alluvium system draining a large (1,804 km2) basin; hence typical bed-material transport analyses and ecologic and geomorphic lessons of in-stream gravel extraction on more gravel-rich rivers have limited applicability. Consequently, we have relied upon multiple analyses, including comprehensive historical mapping, bedload transport modeling, and a GIS-based sediment yield analysis to assess patterns of bed-material transport and annual rates of bed-material flux. These analyses, combined with numerous historical accounts, indicate that since at least the 1840’s, the Umpqua River planform has been stable, as bar geometry is largely fixed by valley physiography and the channel itself is underlain mainly by bedrock. Preliminary estimates of annual bedload transport rates calculated for the period 1951-2008 from bed-material transport capacity relations at 42 bars along the South Umpqua and mainstem Umpqua Rivers vary from 0 to 600,000 metric tons per year, with this large spread reflecting variability in bar geometry and grainsize. Large stable bars are activated only during exceptionally large floods and have negligible transport during most years whereas smaller, low elevation bars serve as transient storage for gravel transported during typical flood events. A more plausible range of average annual transport rates, based on bedload transport capacity estimates for bars with reasonable values for reference shear stress, is 500-50,000 metric tons/year. Our sediment yield and mapping analyses support these more conservative estimates, providing annual transport rates of 13,000-50,000 metric tons per year for the South Umpqua River and mainstem Umpqua River through the Coast Range. Downstream, predicted flux rates decrease as attrition exceeds input of bed material, gradually diminishing to 30,000-40,000 metric tons at the head of tide. Because bed-material transport along the supply-limited Umpqua River is highly variable in time and space, the range of predicted flux values is thought to characterize the upper bounds of annual gravel transport.

75 FR 57830 - Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-22

...) the minimum Corporation), burst pressure to 86.18 Haryana. bar (1250PSIG); change paragraph 7.(2)(l) hydrostatic test pressure 34.74 bar to (500 PSIG) instead of 34.74 bar (500); and add a new drawing. 12629-M... lieu of hydrostatic testing. 12706-M RAGASCO Raufoss.... 49 CFR 173.34; To modify the special 173.201...

46 CFR 154.610 - Design temperature not colder than 0 °C (32 °F).

Code of Federal Regulations, 2010 CFR

2010-10-01

... materials must meet §§ 54.25-1 and 54.25-3 of this chapter. (b) Plates, forgings, rolled and forged bars and... batch of forgings, forged or rolled fittings, and forged or rolled bars and shapes. (f) The specified... ton batch of forgings, forged or rolled fittings and rolled or forged bars and shapes. (h) The...

Quantagenetics® analysis of laser-induced breakdown spectroscopic data: Rapid and accurate authentication of materials

NASA Astrophysics Data System (ADS)

McManus, Catherine E.; Dowe, James; McMillan, Nancy J.

2018-07-01

Many industrial and commercial issues involve authentication of such matters as the manufacturer or geographic source of a material, and quality control of materials, determining whether specific treatments have been properly applied, or if a material is authentic or fraudulent. Often, multiple analytical techniques and tests are used, resulting in expensive and time-consuming testing procedures. Laser-Induced Breakdown Spectroscopy (LIBS) is a rapid laser ablation spectroscopic analytical method. Each LIBS spectrum contains information about the concentration of every element, some isotopic ratios, and the molecular structure of the material, making it a unique and comprehensive signature of the material. Quantagenetics® is a multivariate statistical method based on Bayesian statistics that uses the Euclidian distance between LIBS spectra of materials to classify materials (US Patents 9,063,085 and 8,699,022). The fundamental idea behind Quantagenetics® is that LIBS spectra contain sufficient information to determine the origin and history of materials. This study presents two case studies that illustrate the method. LIBS spectra from 510 Colombian emeralds from 18 mines were classified by mine. Overall, 99.4% of the spectra were correctly classified; the success rate for individual mines ranges from 98.2% to 100%. Some of the mines are separated by distances as little as 200 m, indicating that the method uses the slight but consistent differences in composition to identify the mine of origin accurately. The second study used bars of 17-4 stainless steel from three manufacturers. Each of the three bars was cut into 90 coupons; 30 of each bar received no further treatment, another 30 from each bar received one tempering and hardening treatment, and the final 30 coupons from each bar received a different heat treatment. Using LIBS spectra taken from the coupons, the Quantagenetics® method classified the 270 coupons both by manufacturer (composition) and heat treatment (structure) with an overall success rate of 95.3%. Individual success rates range from 92.4% to 97.6%. These case studies were successful despite having no preconceived knowledge of the materials; artificial intelligence allows the materials to classify themselves without human intervention or bias. Multivariate analysis of LIBS spectra using the Quantagenetics® method has promise to improve quality control and authentication of a wide variety of materials in industrial enterprises.

Basic Principles of Thin-Walled Open Bars Taking into Account Where Influence Shifts of Cross Sections are Concerned

NASA Astrophysics Data System (ADS)

Panasenko, N. N.; Sinelschikov, A. V.

2017-11-01

The finite element method is considered to be the most effective in relation to the calculation of strength and stability of buildings and engineering constructions. As a rule, for the modelling of supporting 3-D frameworks, finite elements with six degrees of freedom are used in each of the nodes. In practice, such supporting frameworks represent the thin-walled welded bars and hot-rolled bars of open and closed profiles in which cross-sectional deplanation must be taken into account. This idea was first introduced by L N Vorobjev and brought to one of the easiest variants of the thin-walled bar theory. The development of this approach is based on taking into account the middle surface shear deformation and adding the deformations of a thin-walled open bar to the formulas for potential and kinetic energy; these deformations depend on shearing stress and result in decreasing the frequency of the first tone of fluctuations to 13%. The authors of the article recommend taking into account this fact when calculating fail-proof dynamic systems.

Selective versus routine patch metal allergy testing to select bar material for the Nuss procedure in 932 patients over 10years.

PubMed

Obermeyer, Robert J; Gaffar, Sheema; Kelly, Robert E; Kuhn, M Ann; Frantz, Frazier W; McGuire, Margaret M; Paulson, James F; Kelly, Cynthia S

2018-02-01

The aim of the study was to determine the role of patch metal allergy testing to select bar material for the Nuss procedure. An IRB-approved (11-04-WC-0098) single institution retrospective, cohort study comparing selective versus routine patch metal allergy testing to select stainless steel or titanium bars for Nuss repair was performed. In Cohort A (9/2004-1/2011), selective patch testing was performed based on clinical risk factors. In Cohort B (2/2011-9/2014), all patients were patch tested. The cohorts were compared for incidence of bar allergy and resultant premature bar loss. Risk factors for stainless steel allergy or positive patch test were evaluated. Cohort A had 628 patients with 63 (10.0%) selected for patch testing, while all 304 patients in Cohort B were tested. Over 10years, 15 (1.8%) of the 842 stainless steel Nuss repairs resulted in a bar allergy, and 5 had a negative preoperative patch test. The incidence of stainless steel bar allergy (1.8% vs 1.7%, p=0.57) and resultant bar loss (0.5% vs 1.3%, p=0.23) was not statistically different between cohorts. An allergic reaction to a stainless steel bar or a positive patch test was more common in females (OR=2.3, p<0.001) and patients with a personal (OR=24.8, p<0.001) or family history (OR=3.1, p<0.001) of metal sensitivity. Stainless steel bar allergies occur at a low incidence with either routine or selective patch metal allergy testing. If selective testing is performed, it is advisable in females and patients with a personal or family history of metal sensitivity. A negative preoperative patch metal allergy test does not preclude the possibility of a postoperative stainless steel bar allergy. Level III Treatment Study and Study of Diagnostic Test. Copyright © 2017 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, B.; Nelson, K.; Lipinski, R.

Iridium alloys have superior strength and ductility at elevated temperatures, making them useful as structural materials for certain high-temperature applications. However, experimental data on their high-strain -rate performance are needed for understanding high-speed impacts in severe environments. Kolsky bars (also called split Hopkinson bars) have been extensively employed for high-strain -rate characterization of materials at room temperature, but it has been challenging to adapt them for the measurement of dynamic properties at high temperatures. In our study, we analyzed the difficulties encountered in high-temperature Kolsky bar testing of thin iridium alloy specimens in compression. We made appropriate modifications using themore » current high-temperature Kolsky bar technique in order to obtain reliable compressive stress–strain response of an iridium alloy at high-strain rates (300–10 000 s -1) and temperatures (750 and 1030°C). The compressive stress–strain response of the iridium alloy showed significant sensitivity to both strain rate and temperature.« less

A Kolsky tension bar technique using a hollow incident tube

NASA Astrophysics Data System (ADS)

Guzman, O.; Frew, D. J.; Chen, W.

2011-04-01

Load control of the incident pulse profiles in compression Kolsky bar experiments has been widely used to subject the specimen to optimal testing conditions. Tension Kolsky bars have been used to determine dynamic material behavior since the 1960s with limited capability to shape the loading pulses due to the pulse-generating mechanisms. We developed a modified Kolsky tension bar where a hollow incident tube is used to carry the incident stress waves. The incident tube also acts as a gas gun barrel that houses the striker for impact. The main advantage of this new design is that the striker impacts on an impact cap of the incident tube. Compression pulse shapers can be attached to the impact cap, thus fully utilizing the predictive compression pulse-shaping capability in tension experiments. Using this new testing technique, the dynamic tensile material behavior for Al 6061-T6511 and TRIP 800 (transformation-induced plasticity) steel has been obtained.

DETECTORS AND EXPERIMENTAL METHODS: Studies of a scintillator-bar detector for a neutron wall at an external target facility

NASA Astrophysics Data System (ADS)

Yu, Yu-Hong; Xu, Hua-Gen; Xu, Hu-Shan; Zhan, Wen-Long; Sun, Zhi-Yu; Guo, Zhong-Yan; Hu, Zheng-Guo; Wang, Jian-Song; Chen, Jun-Ling; Zheng, Chuan

2009-07-01

To achieve a better time resolution of a scintillator-bar detector for a neutron wall at the external target facility of HIRFL-CSR, we have carried out a detailed study of the photomultiplier, the wrapping material and the coupling media. The timing properties of a scintillator-bar detector have been studied in detail with cosmic rays using a high and low level signal coincidence. A time resolution of 80 ps has been achieved in the center of the scintillator-bar detector.

The Effects of Perceptions of Parents' Use of Social and Material Rewards on Prosocial Behaviors in Spanish and U.S. Youth

ERIC Educational Resources Information Center

Carlo, Gustavo; Samper, Paula; Malonda, Elisabeth; Tur-Porcar, Ana M.; Davis, Alexandra

2018-01-01

We examined the links between perceived parental use of social and material rewards and prosocial behaviors across youth from two countries. Six hundred forty adolescents (297 girls; X-bar age = 15.32 years) from Valencia, Spain, and 552 adolescents (321 girls; X-bar age = 13.38 years) from the United States completed measures of their perceptions…

Enhanced sediment loading facilitates point bar growth and accelerates bank erosion along a modelled meander bend on the Sacramento River, USA

NASA Astrophysics Data System (ADS)

Ahmed, J.; Constantine, J. A.; Hales, T. C.

2017-12-01

Meandering channels provide a conduit through which sediment and water is routed from the uplands to the sea. Alluvial material is periodically stored and transported through the channel network as permitted by the prevailing hydrologic conditions. The lowlands are typically characterised by accumulations of sediment attached to the inner banks of meander bends (point bars). These bedforms have been identified as important for facilitating a link between in-stream sediment supplies and channel dynamism. A 2D curvilinear hydrodynamic model (MIKE 21C) was used to perform a number of experiments in which the sediment load was adjusted to investigate how changes in alluvial material fluxes affect the development of point bars and the resultant patterns of bank erosion. A doubling of the sediment load caused a longitudinal increase in the bar in the upstream direction and caused a coeval doubling of the transverse channel slope at the meander apex. The upstream growth of the point bar was accompanied by an increase in length over which lateral migration took place at the outer bank. The magnitude of outer bank erosion was 9-times greater for the high-sediment simulation. These results suggest that enhanced sediment loads (potentially the result of changes in land use or climate) can trigger greater rates of bank erosion and channel change through the sequestration of alluvial material on point bars, which encourage high-velocity fluid deflection towards the outer bank of the meander. This controls riparian habitat development and exchanges of sediment and nutrients across the channel-floodplain interface.

Study of aging and embrittlement of microalloyed steel bars

NASA Astrophysics Data System (ADS)

Campillo, B.; Perez, R.; Martinez, L.

1996-10-01

The aging of hooks, anchors, and other bent reinforcing steel bars in concrete structures are considered in modern international standards. Rebend test procedures have been designed in order to predict the aging embrittlement susceptibility by submerging bent reinforcing bar specimens in boiling water. Subsequently the bars are rebent or straightened in order to determine the loss of ductility or embrittlement of the aged material. The present work considers the influence of carbon, sulfur, and niobium on the performance of reinforcing bars in rebend tests of 300 heats of microalloyed steel bars with a variety of compositions. The microstructural evidence and the statistical results clearly indicate the strong influence of carbon and sulfur on rebend failure, while niobium-rich precipitates contribute to the hardening of the ferrite grains during aging.

Low-cost laser diode array

DOEpatents

Freitas, B.L.; Skidmore, J.A.

1999-06-01

A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost. 19 figs.

Low-cost laser diode array

DOEpatents

Freitas, Barry L.; Skidmore, Jay A.

1999-01-01

A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost.

Evaluating topologically diverse metal–organic frameworks for cryo-adsorbed hydrogen storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gómez-Gualdrón, Diego A.; Colón, Yamil J.; Zhang, Xu

Metal–organic frameworks (MOFs) are porous materials synthesized by combining inorganic and organic molecular building blocks into crystalline networks of distinct topologies. Due to the combinatorial possibilities, there are millions of possible MOF structures. Aiming to exploit their exceptional tunability, surface areas and pore volumes, researchers have investigated MOFs for storage of gaseous fuels such as hydrogen for over a decade, but a suitable MOF to store hydrogen at ambient conditions has not yet been found. Here, we sought to rapidly determine the viability of using MOFs for hydrogen storage at recently proposed, cryogenic operating conditions. We constructed a large andmore » structurally diverse set of 13 512 potential MOF structures based on 41 different topologies and used molecular simulation to determine MOF hydrogen deliverable capacities between 100 bar/77 K and 5 bar/160 K. The highest volumetric deliverable capacity was 57 g L-1 of MOF, which surpasses the 37 g L-1 of tank of the incumbent technology (compressing hydrogen to 700 bar at ambient temperature). To validate our in silico MOF construction method, we synthesized a new isoreticular family of MOFs (she-MOF-x series) based on the she topology, which is extremely rare among MOFs. To validate our hydrogen storage predictions, we activated and measured hydrogen adsorption on she-MOF-1 and NU-1103. The latter MOF showed outstanding stability and a good combination of volumetric and gravimetric performance, presenting 43.2 g L-1 of MOF and 12.6 wt% volumetric and gravimetric deliverable capacities, respectively.« less

Extreme water loss and abiotic O2 buildup on planets throughout the habitable zones of M dwarfs.

PubMed

Luger, R; Barnes, R

2015-02-01

We show that terrestrial planets in the habitable zones of M dwarfs older than ∼1 Gyr could have been in runaway greenhouses for several hundred million years following their formation due to the star's extended pre-main sequence phase, provided they form with abundant surface water. Such prolonged runaway greenhouses can lead to planetary evolution divergent from that of Earth. During this early runaway phase, photolysis of water vapor and hydrogen/oxygen escape to space can lead to the loss of several Earth oceans of water from planets throughout the habitable zone, regardless of whether the escape is energy-limited or diffusion-limited. We find that the amount of water lost scales with the planet mass, since the diffusion-limited hydrogen escape flux is proportional to the planet surface gravity. In addition to undergoing potential desiccation, planets with inefficient oxygen sinks at the surface may build up hundreds to thousands of bar of abiotically produced O2, resulting in potential false positives for life. The amount of O2 that builds up also scales with the planet mass; we find that O2 builds up at a constant rate that is controlled by diffusion: ∼5 bar/Myr on Earth-mass planets and up to ∼25 bar/Myr on super-Earths. As a result, some recently discovered super-Earths in the habitable zone such as GJ 667Cc could have built up as many as 2000 bar of O2 due to the loss of up to 10 Earth oceans of water. The fate of a given planet strongly depends on the extreme ultraviolet flux, the duration of the runaway regime, the initial water content, and the rate at which oxygen is absorbed by the surface. In general, we find that the initial phase of high luminosity may compromise the habitability of many terrestrial planets orbiting low-mass stars.

Martian Meanders and Scroll-Bars

NASA Image and Video Library

2017-03-01

This is a portion of an inverted fluvial channel in the region of Aeolis/Zephyria Plana, at the Martian equator. Channels become inverted when the sediments filling them become more resistant to erosion than the surrounding material. Here, the most likely process leading to hardening of the channel material is chemical cementation by precipitation of minerals. Once the surrounding material erodes, the channel is left standing as a ridge. The series of curvilinear lineations are ancient scroll-bars, which are features typical of river meanders (bends) in terrestrial fluvial channels. Scroll-bars are series of ridges that result from the continuous lateral migration of a meander. On Earth, they are more common in mature rivers. The presence of scroll bars suggests that the water flow in this channel may have been sustained for a relatively long time. Measuring characteristics of these scroll-bars and meanders may help to estimate the amount of water that once flowed in this channel, aiding our understanding of the history of water on Mars. The map is projected here at a scale of 25 centimeters (9.8 inches) per pixel. [The original image scale is 29.3 centimeters (11.5 inches) per pixel (with 1 x 1 binning); objects on the order of 88 centimeters (29.6 inches) across are resolved.] North is up. http://photojournal.jpl.nasa.gov/catalog/PIA21551

Development and Application of High Performance Quenched and Tempered Wear Resistant Steels in Material Handling and Construction Machinery

NASA Astrophysics Data System (ADS)

Su, Fenwei; Sidiras, Evangelos

The demand for more sustainable development promotes the need for components and steel structures with a longer useful life and better performance. Upgrade of wear steel plate used in key industry segments such as mining, recycling and road building results in the stable growth of global market with high quality grade Q&T wear plates (Hardness HBW≥400, and Yield strength ≥690 Mpa). SSAB has now expanded its wear steel product range by both thicker and thinner Q&T plate to meet the needs of the market, and can offer wear plates from 0.7 mm to 160 mm. The continuous research and development is being done to offer even thicker plates. This article introduces the performance and advantages of high quality grade Q&T wear resistant steel products (plate, strip, tube and round bars) produced in SSAB, and also describes typical applications in some industrial segments such as material handling and construction machinery.

Extreme-value statistics reveal rare failure-critical defects in additive manufacturing

DOE PAGES

Boyce, Brad L.; Salzbrenner, Bradley C.; Rodelas, Jeffrey M.; ...

2017-04-21

Additive manufacturing enables the rapid, cost effective production of large populations of material test coupons such as tensile bars. By adopting streamlined test methods including ‘drop-in’ grips and non-contact extensometry, testing these large populations becomes more efficient. Unlike hardness tests, the tensile test provides a direct measure of yield strength, flow properties, and ductility, which can be directly incorporated into solid mechanics simulations. In the present work, over 1000 nominally identical tensile tests were used to explore the effect of process variability on the mechanical property distributions of a precipitation hardened stainless steel, 17-4PH, produced by a laser powder bedmore » fusion process, also known as direct metal laser sintering. With this large dataset, rare defects are revealed that affect only ~2% of the population, stemming from a single build lot of material. Lastly, the rare defects caused a substantial loss in ductility and were associated with an interconnected network of porosity.« less

Slab replacement and dowel bar retrofit, district 11, San Diego County

DOT National Transportation Integrated Search

2002-01-01

The project Resident Engineer requested that the Office of Rigid Pavement Materials and Structural Concrete examine cracking in replacement slabs and dowel bar retrofit installations on a project rehabilitating a section of Route 08 in District 11 ne...

The use of water-jetting technology in prostheses revision surgery-first results of parameter studies on bone and bone cement.

PubMed

Honl, M; Rentzsch, R; Müller, G; Brandt, C; Bluhm, A; Hille, E; Louis, H; Morlock, M

2000-01-01

Water-jet cutting techniques have been used in industrial applications for many different materials. Recently these techniques have been developed into a revolutionary cutting tool for soft tissues in visceral surgery. The present study investigates the usage of this cutting technology for the revision surgery of endoprostheses. In the first part of the study, samples of bovine bone and acrylic bone cement (PMMA) were cut using an industrial jet cutting device with pure water. Below 400 bar, only PMMA was cut; above 400 bar, bone was also cut, but only pressures above 800 bar resulted in clinically useful rates of material removal (cut depth 2. 4 mm at 10 mm/min traverse speed). In the second part of the study, the effect of adding biocompatible abrasives to the water in order to reduce the required pressure was investigated, resulting in a significantly higher removal of material. At 600 bar, PMMA was cut 5. 2 mm deep with plain water and 15.2 mm deep with added abrasives. The quality of the cuts was increased by the abrasive. Though there was no clear selectivity between bone and PMMA any more, the rate of material removal at similar pressures was significantly higher for PMMA than for bone (600 bar: 1.6 mm cut depth for bone samples, 15.2 mm for PMMA). The measured cut depths with either method were not influenced by a change of the cutting direction with respect to the main direction of the osteons in the bone. However, a reduction of the jet surface angle (90 degrees to 23 degrees ) resulted for bone in a significantly lower cut depth at 600 bar (plain water: 0.62 mm vs. 0.06 mm; abrasive: 1.61 mm vs. 0.60 mm). The laboratory experiments indicate that abrasive water jets may be suitable for cutting biomaterials like bone and bone cement. Copyright 2000 John Wiley & Sons, Inc.

Stone decay assessment of the Madrid's Royal Palace (Spain) by means of ultrasound and magnetometric prospection

NASA Astrophysics Data System (ADS)

Fort, R.; Alvarez de Buergo, M.

2012-04-01

The architrave of the entablature of the 4 façades of the Palace was built in a limestone known as Colmenar stone (biomicrite), a traditional material used for construction in Madrid. This stone shows such petrophysical properties that make it resistant to decay processes. Despite its high quality, the ashlars of the architrave have undergone fissuring processes resulting on fragments fall, some of them being blocks weighing more than 300 Kg, with the consequent risk for visitors and passers-by. Fissures were caused by the presence of metallic elements (iron-based) used to tie ashlars. These elements, which could have performed properly in absence of water, underwent oxidation processes due to the water entrance, exerting significant pressures inside the stone that derive into fractures with their planes being almost parallel to the façade surface. Once verified that the presence of these metallic elements, and their oxidation, was the cause of the ashlars fissuring, an inspection of the building façades architrave was performed by using two portable and non destructive techniques: magnetometry for detecting iron elements, and ultrasound velocity prospection for detecting non visible stone fissures behind the surface. This survey will allow defining the guidelines for a restoration intervention. The inspection of the architrave consisted of analysing around 1100 ashlars (circa 600 meters long were surveyed), during a lapse of time of one year, in 4 survey campaigns, one for each façade, with the aid of a mobile and self-operating that allows to reach up to 40 m high. Results from the magnetometry prospection made possible to locate metallic elements (flat bars and cramps), and sometimes the flat bars overlapping. Such bars are usually located at 3-5 cm deep from the surface, just below the freeze and in a case cut in the architrave limestone. In the areas of flat bars overlapping, a depth from the surface into the façade of 8-10 cm was measured. Such bars were several meters long, tieing several ashlars, from 55 to 65 mm wide, and 15-20 mm thick. In vaulted areas of the frieze, iron beams were detected, of around 9 cm thick, as well as iron angle bars behind the mentioned iron beams, vertically arranged and going through the architrave. The ultrasound propagation velocity survey in all the architrave ashlars was carried out by means of the indirect or surface mode, using a measuring net of 15 cm side and 20 to 30 readings in each element. Results obtained allowed detecting fissures inside the ashlars non visible at the stone surface. Main fissures were located in areas of cramp-stone coupling. Therefore, this technique was sucessful in locating architrave ashlars with risk of fall, and thus it made possible to plan the structural intervention to consolidate these elements by micro reinforcement with stainless materials (e.g. glass fiber).

10. COPY OF PHOTOGRAPH TAKEN SEPT. 21, 1926. LABELED 'MCKINNEY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. COPY OF PHOTOGRAPH TAKEN SEPT. 21, 1926. LABELED 'MCKINNEY STEEL PLANT.' PHOTO SHOWS THE ORIGINAL NUCLEUS OF CORRIGAN, MCKINNEY CO. STEEL PLANT: MIXER BUILDING, OPEN HEARTH BUILDING, 40-INCH BLOOMING MILL (21 inch and 18 inch SHEET BAR AND BILLET MILLS NOT VISIBLE.) VIEW LOOKING NORTH. PHOTO COURTESY THE CLEVELAND PLAIN DEALER. - Corrigan, McKinney Steel Company, 3100 East Forty-fifth Street, Cleveland, Cuyahoga County, OH

Dowel Bar Retrofit Mix Design and Specification : Technical Report

DOT National Transportation Integrated Search

2012-01-01

Current INDOT specifications for repair materials to be used in dowel bar retrofit (DBR) applications (Sections 507.08 and 901.07 of INDOTs Book of Specifications) are based, in large part, on the requirements of ASTM C 928 and the manufacturer-pr...

High Temperature Heat Exchanger Design and Fabrication for Systems with Large Pressure Differentials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chordia, Lalit; Portnoff, Marc A.; Green, Ed

The project’s main purpose was to design, build and test a compact heat exchanger for supercritical carbon dioxide (sCO 2) power cycle recuperators. The compact recuperator is required to operate at high temperature and high pressure differentials, 169 bar (~2,500 psi), between streams of sCO 2. Additional project tasks included building a hot air-to-sCO 2 Heater heat exchanger (HX) and design, build and operate a test loop to characterize the recuperator and heater heat exchangers. A novel counter-current microtube recuperator was built to meet the high temperature high differential pressure criteria and tested. The compact HX design also incorporated amore » number of features that optimize material use, improved reliability and reduced cost. The air-to-sCO 2 Heater HX utilized a cross flow, counter-current, micro-tubular design. This compact HX design was incorporated into the test loop and exceeded design expectations. The test loop design to characterize the prototype Brayton power cycle HXs was assembled, commissioned and operated during the program. Both the prototype recuperator and Heater HXs were characterized. Measured results for the recuperator confirmed the predictions of the heat transfer models developed during the project. Heater HX data analysis is ongoing.« less

Overdenture retaining bar stress distribution: a finite-element analysis.

PubMed

Caetano, Conrado Reinoldes; Mesquita, Marcelo Ferraz; Consani, Rafael Leonardo Xediek; Correr-Sobrinho, Lourenço; Dos Santos, Mateus Bertolini Fernandes

2015-05-01

Evaluate the stress distribution on the peri-implant bone tissue and prosthetic components of bar-clip retaining systems for overdentures presenting different implant inclinations, vertical misfit and framework material. Three-dimensional models of a jaw and an overdenture retained by two implants and a bar-clip attachment were modeled using specific software (SolidWorks 2010). The studied variables were: latero-lateral inclination of one implant (-10°, -5°, 0°, +5°, +10°); vertical misfit on the other implant (50, 100, 200 µm); and framework material (Au type IV, Ag-Pd, Ti cp, Co-Cr). Solid models were imported into mechanical simulation software (ANSYS Workbench 11). All nodes on the bone's external surface were constrained and a displacement was applied to simulate the settling of the framework on the ill-fitted component. Von Mises stress for the prosthetic components and maximum principal stress to the bone tissue were evaluated. The +10° inclination presented the worst biomechanical behavior, promoting the highest stress values on the bar framework and peri-implant bone tissue. The -5° group presented the lowest stress values on the prosthetic components and the lowest stress value on peri-implant bone tissue was observed in -10°. Increased vertical misfit caused an increase on the stress values in all evaluated structures. Stiffer framework materials caused a considerable stress increase in the framework itself, prosthetic screw of the fitted component and peri-implant bone tissue. Inclination of one implant associated with vertical misfit caused a relevant effect on the stress distribution in bar-clip retained overdentures. Different framework materials promoted increased levels of stress in all the evaluated structures.

Torsion of a Cosserat elastic bar with square cross section: theory and experiment

NASA Astrophysics Data System (ADS)

Drugan, W. J.; Lakes, R. S.

2018-04-01

An approximate analytical solution for the displacement and microrotation vector fields is derived for pure torsion of a prismatic bar with square cross section comprised of homogeneous, isotropic linear Cosserat elastic material. This is accomplished by analytical simplification coupled with use of the principle of minimum potential energy together with polynomial representations for the desired field components. Explicit approximate expressions are derived for cross section warp and for applied torque versus angle of twist of the bar. These show that torsional rigidity exceeds the classical elasticity value, the difference being larger for slender bars, and that cross section warp is less than the classical amount. Experimental measurements on two sets of 3D printed square cross section polymeric bars, each set having a different microstructure and four different cross section sizes, revealed size effects not captured by classical elasticity but consistent with the present analysis for physically sensible values of the Cosserat moduli. The warp can allow inference of Cosserat elastic constants independently of any sensitivity the material may have to dilatation gradients; warp also facilitates inference of Cosserat constants that are difficult to obtain via size effects.

Application of high-speed photography to chip refining

NASA Astrophysics Data System (ADS)

Stationwala, Mustafa I.; Miller, Charles E.; Atack, Douglas; Karnis, A.

1991-04-01

Several high speed photographic methods have been employed to elucidate the mechanistic aspects of producing mechanical pulp in a disc refiner. Material flow patterns of pulp in a refmer were previously recorded by means of a HYCAM camera and continuous lighting system which provided cine pictures at up to 10,000 pps. In the present work an IMACON camera was used to obtain several series of high resolution, high speed photographs, each photograph containing an eight-frame sequence obtained at a framing rate of 100,000 pps. These high-resolution photographs made it possible to identify the nature of the fibrous material trapped on the bars of the stationary disc. Tangential movement of fibre floes, during the passage of bars on the rotating disc over bars on the stationary disc, was also observed on the stator bars. In addition, using a cinestroboscopic technique a large number of high resolution pictures were taken at three different positions of the rotating disc relative to the stationary disc. These pictures were computer analyzed, statistically, to determine the fractional coverage of the bars of the stationary disc with pulp. Information obtained from these studies provides new insights into the mechanism of the refining process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Nelson, Kevin; Lipinski, Ronald J.

Iridium alloys have superior strength and ductility at elevated temperatures, making them useful as structural materials for certain high-temperature applications. However, experimental data on their high-temperature high-strain-rate performance are needed for understanding high-speed impacts in severe elevated-temperature environments. Kolsky bars (also called split Hopkinson bars) have been extensively employed for high-strain-rate characterization of materials at room temperature, but it has been challenging to adapt them for the measurement of dynamic properties at high temperatures. Current high-temperature Kolsky compression bar techniques are not capable of obtaining satisfactory high-temperature high-strain-rate stress-strain response of thin iridium specimens investigated in this study. We analyzedmore » the difficulties encountered in high-temperature Kolsky compression bar testing of thin iridium alloy specimens. Appropriate modifications were made to the current high-temperature Kolsky compression bar technique to obtain reliable compressive stress-strain response of an iridium alloy at high strain rates (300 – 10000 s -1) and temperatures (750°C and 1030°C). Uncertainties in such high-temperature high-strain-rate experiments on thin iridium specimens were also analyzed. The compressive stress-strain response of the iridium alloy showed significant sensitivity to strain rate and temperature.« less

The significance of sediment transport in arroyo development

USGS Publications Warehouse

Meyer, David F.

1989-01-01

Arroyo widening dominates postincisional arroyo development, and the manner of widening is dependent on the grain size of bed material transported by the channel. When bed material is predominantly gravel, subaqueous bars that alternate from one side of the channel to the other form during high flows in initially narrow, often straight, arroyos. These alternate bars grow and become coarse-grained point bars. Moderate and low flows cannot rework these coarse bars, and the channel meanders around them. Arroyo walls opposite the bars are undercut and eroded. With progressive arroyo widening by erosion of cut banks, high-flow channel width increases, and depth decreases, reducing channel competence. Gravel is deposited in midchannel bars, point bars are reworked, and the channel becomes braided. As braiding becomes dominant, both arroyo walls are eroded. This conceptual model of coarse-grained arroyo development is based on observations of arroyo development through time using physical models and interpretation of the channel and arroyo morphology and sedimentology during a short period along the San Simon, San Pedro, and Santa Cruz Rivers in southeast Arizona. When bed material is predominantly sand, the channel pattern within initial arroyos is typically braided, and both arroyo walls are actively eroded. Alternate bars may form within single-thread, high-flow channels, but they are reworked during recessional flows, and the .low-flow channel is again braided. With progressive arroyo widening, fine sand, silt, and clay carried in suspension are deposited across a flood plain within the wide arroyo, causing the channel to meander. This fine-grained arroyo development model is based on observations of arroyo development through time using physical models and interpretation of the channel and arroyo morphology and sedimentology during a short period along the Rio Puerco, New Mexico. Experimental investigations using physical models in which incised channels were monitored through time indicate that the rate of arroyo widening is dependent on the amount of bedload transported through a reach. This is documented by the relations between the rate of arroyo erosion and the observed sediment transport, the channel slope, the channel width and the channel width-to-depth ratio. When a small amount of bed material is being transported, arroyos do not widen whether they are narrow (arroyo width-to-depth ratios between 1.5 and 3.1), intermediate (between 2.5 and 4.8), or wide (greater than 4.9). Arroyo widening resumes when a larger supply of bed material is introduced. Arroyo widening decreases through time because with progressive increases of arroyo width, the frequency with which unstable channels within the arroyo impinge upon arroyo walls decreases. Arroyos become wider in a downstream direction in response to the cumulative effect of upstream sediment production.

Evaluation of alternative dowel bar materials and coatings : executive summary report.

DOT National Transportation Integrated Search

2011-01-01

The inclusion of steel dowel bars to transfer forces across sawed or formed transverse joints from one concrete pavement slab to another while permitting expansion and contraction movements of the concrete has been a basic design practice in most U.S...

Dynamic High-temperature Testing of an Iridium Alloy in Compression at High-strain Rates: Dynamic High-temperature Testing

DOE PAGES

Song, B.; Nelson, K.; Lipinski, R.; ...

2014-08-21

Iridium alloys have superior strength and ductility at elevated temperatures, making them useful as structural materials for certain high-temperature applications. However, experimental data on their high-strain -rate performance are needed for understanding high-speed impacts in severe environments. Kolsky bars (also called split Hopkinson bars) have been extensively employed for high-strain -rate characterization of materials at room temperature, but it has been challenging to adapt them for the measurement of dynamic properties at high temperatures. In our study, we analyzed the difficulties encountered in high-temperature Kolsky bar testing of thin iridium alloy specimens in compression. We made appropriate modifications using themore » current high-temperature Kolsky bar technique in order to obtain reliable compressive stress–strain response of an iridium alloy at high-strain rates (300–10 000 s -1) and temperatures (750 and 1030°C). The compressive stress–strain response of the iridium alloy showed significant sensitivity to both strain rate and temperature.« less

5. Photocopy of drawing, November 3, 1919. PLANS AND ELEVATIONS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Photocopy of drawing, November 3, 1919. PLANS AND ELEVATIONS, STOREHOUSE FOR BAR STOCK. Watertown Arsenal Engineering Division. Drawing Number 9736. (Original: AMTL Engineering Division, Watertown). - Watertown Arsenal, Building No. 292, Welch Avenue, Watertown, Middlesex County, MA

Complications with computer-aided designed/computer-assisted manufactured titanium and soldered gold bars for mandibular implant-overdentures: short-term observations.

PubMed

Katsoulis, Joannis; Wälchli, Julia; Kobel, Simone; Gholami, Hadi; Mericske-Stern, Regina

2015-01-01

Implant-overdentures supported by rigid bars provide stability in the edentulous atrophic mandible. However, fractures of solder joints and matrices, and loosening of screws and matrices were observed with soldered gold bars (G-bars). Computer-aided designed/computer-assisted manufactured (CAD/CAM) titanium bars (Ti-bars) may reduce technical complications due to enhanced material quality. To compare prosthetic-technical maintenance service of mandibular implant-overdentures supported by CAD/CAM Ti-bar and soldered G-bar. Edentulous patients were consecutively admitted for implant-prosthodontic treatment with a maxillary complete denture and a mandibular implant-overdenture connected to a rigid G-bar or Ti-bar. Maintenance service and problems with the implant-retention device complex and the prosthesis were recorded during minimally 3-4 years. Annual peri-implant crestal bone level changes (ΔBIC) were radiographically assessed. Data of 213 edentulous patients (mean age 68 ± 10 years), who had received a total of 477 tapered implants, were available. Ti-bar and G-bar comprised 101 and 112 patients with 231 and 246 implants, respectively. Ti-bar mostly exhibited distal bar extensions (96%) compared to 34% of G-bar (p < .001). Fracture rate of bars extensions (4.7% vs 14.8%, p < .001) and matrices (1% vs 13%, p < .001) was lower for Ti-bar. Matrices activation was required 2.4× less often in Ti-bar. ΔBIC remained stable for both groups. Implant overdentures supported by soldered gold bars or milled CAD/CAM Ti-bars are a successful treatment modality but require regular maintenance service. These short-term observations support the hypothesis that CAD/CAM Ti-bars reduce technical complications. Fracture location indicated that the titanium thickness around the screw-access hole should be increased. © 2013 Wiley Periodicals, Inc.

In-situ TEM on (de)hydrogenation of Pd at 0.5-4.5 bar hydrogen pressure and 20-400°C.

PubMed

Yokosawa, Tadahiro; Alan, Tuncay; Pandraud, Gregory; Dam, Bernard; Zandbergen, Henny

2012-01-01

We have developed a nanoreactor, sample holder and gas system for in-situ transmission electron microscopy (TEM) of hydrogen storage materials up to at least 4.5 bar. The MEMS-based nanoreactor has a microheater, two electron-transparent windows and a gas inlet and outlet. The holder contains various O-rings to have leak-tight connections with the nanoreactor. The system was tested with the (de)hydrogenation of Pd at pressures up to 4.5 bar. The Pd film consisted of islands being 15 nm thick and 50-500 nm wide. In electron diffraction mode we observed reproducibly a crystal lattice expansion and shrinkage owing to hydrogenation and dehydrogenation, respectively. In selected-area electron diffraction and bright/dark-field modes the (de)hydrogenation of individual Pd particles was followed. Some Pd islands are consistently hydrogenated faster than others. When thermally cycled, thermal hysteresis of about 10-16°C between hydrogen absorption and desorption was observed for hydrogen pressures of 0.5-4.5 bar. Experiments at 0.8 bar and 3.2 bar showed that the (de)hydrogenation temperature is not affected by the electron beam. This result shows that this is a fast method to investigate hydrogen storage materials with information at the nanometer scale. Copyright © 2011 Elsevier B.V. All rights reserved.

Melt growth of organic 4-(2-Phenylisopropyl) phenol single crystal and its structural, thermal, dielectric permittivity and optical properties

NASA Astrophysics Data System (ADS)

Sadhasivam, S.; Rajesh, N. P.

2017-12-01

A nonlinear optical (NLO) organic crystal 4-(2-Phenylisopropyl) phenol has been grown by a top seeded melt growth technique. The melt growth kinetics of solid-liquid (molten) interface and facets formation in melt growth were studied. The melt grown crystal has the (001), (00 1 bar),(110)(1 bar 1 bar 0) ,(1 bar 20),(1 2 bar 0),(2 bar 10) and(2 1 bar 0) different morphological face. The morphological characteristics of melt grown crystal helps to better infer the kinetic influence of melt and hone growth of organic material. The rhombohedral lattice cell parameters were measured by single crystal X-ray diffraction. 4-(2-Phenylisopropyl) phenol crystallizes in space group of R 3 bar . Thermal study shows that solid to liquid transition occurring at 350 K and decomposes at 597 K. The grown crystal was optically transparent in the wavelength range of 300-1100 nm. The low dielectric constant (9-11) was measured in the [001] of 4-(2-Phenylisopropyl) phenol crystal.

The origin of the LMC stellar bar: clues from the SFH of the bar and inner disc

NASA Astrophysics Data System (ADS)

Monteagudo, L.; Gallart, C.; Monelli, M.; Bernard, E. J.; Stetson, P. B.

2018-01-01

We discuss the origin of the Large Magellanic Cloud (LMC) stellar bar by comparing the star formation histories (SFHs) obtained from deep colour-magnitude diagrams (CMDs) in the bar and in a number of fields in different directions within the inner disc. The CMDs, reaching the oldest main-sequence turn-offs in these very crowded fields, have been obtained with VIMOS on the Very Large Telescope in the service mode, under very good seeing conditions. We show that the SFHs of all fields share the same patterns, with consistent variations of the star formation rate as a function of time in all of them. We therefore conclude that no specific event of star formation can be identified with the formation of the LMC bar, which instead likely formed from a redistribution of disc material which occurred when the LMC disc became bar unstable, and shared a common SFH with the inner disc thereafter. The strong similarity between the SFH of the centre and edge of the bar rules out the expected significant spatial variations of the SFH across the bar.

Fusion of UAV photogrammetry and digital optical granulometry for detection of structural changes in floodplains

NASA Astrophysics Data System (ADS)

Langhammer, Jakub; Lendzioch, Theodora; Mirijovsky, Jakub

2016-04-01

Granulometric analysis represents a traditional, important and for the description of sedimentary material substantial method with various applications in sedimentology, hydrology and geomorphology. However, the conventional granulometric field survey methods are time consuming, laborious, costly and are invasive to the surface being sampled, which can be limiting factor for their applicability in protected areas.. The optical granulometry has recently emerged as an image analysis technique, enabling non-invasive survey, employing semi-automated identification of clasts from calibrated digital imagery, taken on site by conventional high resolution digital camera and calibrated frame. The image processing allows detection and measurement of mixed size natural grains, their sorting and quantitative analysis using standard granulometric approaches. Despite known limitations, the technique today presents reliable tool, significantly easing and speeding the field survey in fluvial geomorphology. However, the nature of such survey has still limitations in spatial coverage of the sites and applicability in research at multitemporal scale. In our study, we are presenting novel approach, based on fusion of two image analysis techniques - optical granulometry and UAV-based photogrammetry, allowing to bridge the gap between the needs of high resolution structural information for granulometric analysis and spatially accurate and data coverage. We have developed and tested a workflow that, using UAV imaging platform enabling to deliver seamless, high resolution and spatially accurate imagery of the study site from which can be derived the granulometric properties of the sedimentary material. We have set up a workflow modeling chain, providing (i) the optimum flight parameters for UAV imagery to balance the two key divergent requirements - imagery resolution and seamless spatial coverage, (ii) the workflow for the processing of UAV acquired imagery by means of the optical granulometry and (iii) the workflow for analysis of spatial distribution and temporal changes of granulometric properties across the point bar. The proposed technique was tested on a case study of an active point bar of mid-latitude mountain stream at Sumava mountains, Czech Republic, exposed to repeated flooding. The UAV photogrammetry was used to acquire very high resolution imagery to build high-precision digital terrain models and orthoimage. The orthoimage was then analyzed using the digital optical granulometric tool BaseGrain. This approach allowed us (i) to analyze the spatial distribution of the grain size in a seamless transects over an active point bar and (ii) to assess the multitemporal changes of granulometric properties of the point bar material resulting from flooding. The tested framework prove the applicability of the proposed method for granulometric analysis with accuracy comparable with field optical granulometry. The seamless nature of the data enables to study spatial distribution of granulometric properties across the study sites as well as the analysis of multitemporal changes, resulting from repeated imaging.

Arch bar stabilization of endotracheal tubes in children with facial burns.

PubMed

Perrotta, V J; Stern, J D; Lo, A K; Mitra, A

1995-01-01

Endotracheal tube stabilization in children with facial burns can be difficult. Several methods rely on straps or complex devices that apply undesirable pressure to the face, potentially destroying skin grafts and making wound care difficult. Techniques that rely on a single wire or suture can be unreliable. Presented here is the arch bar method of endotracheal tube stabilization, which appears to be free of these problems. This method employs a standard dental arch bar secured to four maxillary teeth with 24-gauge stainless steel wire. The endotracheal tube is anchored to the arch bar with two pieces of wire or suture material. The arch bar method of endotracheal tube stabilization was used on three patients in the burn center at St. Christopher's Hospital for Children. Wound care and successful skin grafting were performed without difficulty. No complications related to the arch bars occurred.

Making the Venus Concept Watch 1.0

NASA Astrophysics Data System (ADS)

Balint, Tibor S.; Melchiorri, Julian P.

2014-08-01

Over the past year we have celebrated the 50th anniversary of planetary exploration, which started with the Venus flyby of Mariner-2; and the 35th anniversary of the Pioneer-Venus multi-probe mission where one large and three small probes descended to the surface of Venus, encountering extreme environmental conditions. At the surface of Venus the temperature is about 460 °C, and the pressure is 92 bar, with a highly corrosive super-critical CO2 atmosphere. At a Venusian altitude of 50 km the pressure and temperature conditions are near Earth-like, but the clouds carry sulfuric acid droplets. Deep probe missions to Jupiter and Saturn, targeting the 100 bar pressure depth encounter similar pressure and temperature conditions as the Pioneer-Venus probes did. Mitigating these environments is highly challenging and requires special considerations for designs and materials. While assessing such space mission concepts, we have found that there is an overlap between the extreme environments in planetary atmospheres and the environments experienced by deep-sea explorers back on Earth. Consequently, the mitigation approaches could be also similar between planetary probes and diver watches. For example, both need to tolerate about 100 bar of pressure-although high temperatures are not factors on Earth. Mitigating these environments, the potential materials are: titanium for the probe and the watch housing; sapphire for the window and glass; resin impregnated woven carbon fiber for the aeroshell's thermal protection system and for the face of the watch; and nylon ribbon for the parachute and for the watch band. Planetary probes also utilize precision watches; thus there is yet another crosscutting functionality with diver watches. Our team, from the Innovation Design Engineering Program of the Royal College of Art, has designed and built a concept watch to commemorate these historical events, while highlighting advances in manufacturing processes over the past three to five decades, relevant to both future planetary mission designs and can be used to produce deep diver watches. In this paper we describe our design considerations; give a brief overview of the extreme environments these components would experience on both Venus and Earth; the manufacturing techniques and materials we used to build the Venus Watch; and its outreach potential to bring a distant concept of planetary exploration closer to Earth. We will also address lessons learned from this project and new ideas forward, for the next generation of this concept design.

A General and Mild Approach to Controllable Preparation of Manganese-Based Micro- and Nanostructured Bars for High Performance Lithium-Ion Batteries.

PubMed

Ma, Guo; Li, Sheng; Zhang, Weixin; Yang, Zeheng; Liu, Shulin; Fan, Xiaoming; Chen, Fei; Tian, Yuan; Zhang, Weibo; Yang, Shihe; Li, Mei

2016-03-07

One-dimensional (1D) micro- and nanostructured electrode materials with controllable phase and composition are appealing materials for use in lithium-ion batteries with high energy and power densities, but they are challenging to prepare. Herein, a novel ethanol-water mediated co-precipitation method by a chimie douce route (synthesis conducted under mild conditions) has been exploited to selectively prepare an extensive series of manganese-based electrode materials, manifesting the considerable generalizability and efficacy of the method. Moreover, by simply tuning the mixed solvent and reagents, transition metal oxide bars with differing aspect ratios and compositions were prepared with an unprecedented uniformity. Application prospects are demonstrated by Li-rich 0.5 Li2 MnO3 ⋅0.5 LiNi1/3 Co1/3 Mn1/3 O2 bars, which demonstrate excellent reversible capacity and rate capability thanks to the steerable nature of the synthesis and material quality. This work opens a new route to 1D micro- and nanostructured materials by customizing the precipitating solvent to orchestrate the crystallization process. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

8. Photocopied August 1978. BREAKING CONCRETE BARS, JULY 1898. TESTING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. Photocopied August 1978. BREAKING CONCRETE BARS, JULY 1898. TESTING MACHINE USED BY VON SCHON IN EXPERIMENTS ON METHODS OF MIXING CONCRETE AND ON CONCRETE AGGREGATES WHICH USED LOCAL MATERIALS. (4) - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

Intraocular foreign-body hazard during vitrectomy.

PubMed

Bovino, J A; Marcus, D F

1982-03-01

We noted two instances of forceps-induced fragmentation of the bar used for scleral plug storage during vitreous surgery. The silicone bar material was adherent to the plug in both cases. Because this represents a significant intraocular foreign body hazard, the scleral plug should be carefully inspected before insertion.

Southwest Washington littoral drift restoration—Beach and nearshore morphological monitoring

USGS Publications Warehouse

Stevens, Andrew W.; Gelfenbaum, Guy; Ruggiero, Peter; Kaminsky, George M.

2012-01-01

A morphological monitoring program has documented the placement and initial dispersal of beach nourishment material (280,000 m3) placed between the Mouth of the Columbia River (MCR) North Jetty and North Head, at the southern end of the Long Beach Peninsula in southwestern Washington State. A total of 21 topographic surveys and 8 nearshore bathymetric surveys were performed between July 11, 2010, and November 4, 2011. During placement, southerly alongshore transport resulted in movement of nourishment material to the south towards the MCR North Jetty. Moderate wave conditions (significant wave height around 4 m) following the completion of the nourishment resulted in cross-shore sediment transport, with most of the nourishment material transported into the nearshore bars. The nourishment acted as a buffer to the more severe erosion, including dune overtopping and retreat, that was observed at the northern end of the study area throughout the winter. One year after placement of the nourishment, onshore transport and beach recovery were most pronounced within the permit area and to the south toward the MCR North Jetty. This suggests that there is some long-term benefit of the nourishment for reducing erosion rates locally, although the enhanced recovery also could be due to natural gradients in alongshore transport causing net movement of the sediment from north to south. Measurements made during the morphological monitoring program documented the seasonal movement and decay of nearshore sand bars. Low-energy conditions in late summer resulted in onshore bar migration early in the monitoring program. Moderate wave conditions in the autumn resulted in offshore movement of the middle bar and continued onshore migration of the outer bar. High-energy wave conditions early in the winter resulted in strong cross-shore transport and creation of a 3-bar system along portions of the coast. More southerly wave events occurred later in the winter and early spring and coincided with the complete loss of the outer bar and net loss of sediment from the study area. These data suggest that bar decay may be an important mechanism for exporting sediment from Benson Beach north to the Long Beach Peninsula. The measurements presented in this report represent one component of a broader monitoring program designed to track the movement of nourishment material on the beach and shoreface at this location, including continuous video monitoring (Argus), in situu measurements of hydrodynamics, and a physical tracer experiment. Field data from the monitoring program will be used to test numerical models of hydrodynamics and sediment transport and to improve the capability of numerical models to support regional sediment management.

Numerical Analysis on Tensile Properties of Grout-filled Splice Sleeve Rebars under ISO 834 Standard Fire

NASA Astrophysics Data System (ADS)

Liu, Yong Jun; Li, Chao; Zhou, When Jun

2018-06-01

This paper presents some numerical simulation results of tensile properties of reinforcing bars spliced by grout-filled coupling sleeves under fire conditions to identify the effect of load ratio on fire resistance time of spliced reinforcing bars, which provide a useful base for predicting structural behaviors of pre-cast reinforced concrete buildings in fires. A spliced rebar system investigated in this paper consists of two equal-diameter steel reinforcing bars with 25mm diameter and a straight coupling sleeve with 50mm outer and 45mm inner diameters. As a result, the thickness of grout between steel bars and sleeves are 20mm. Firstly, the temperature distributions in steel bars connected by grout- filled coupling sleeves exposed to ISO 834 standard fire were calculated utilizing finite element analysis software ANSYS. Secondly, the stress changes in heated steel bars connected by grout-filled coupling sleeves under different constant tensile loads were calculated step by step until the rebar system failed due to fire. Thus, the fire resistant time of rebar spliced by grout-filled coupling sleeves under different axial tensile loads can be determined, further, the relationship between fire resistance time and axial tensile loads ratio can could be obtained. Finally, the fire resistant times versus axial tensile load ratios curve of grout-filled splice sleeve rebars exposed to ISO 834 standard fire is presented.

Integrity assessment of grouted posttensioning cables and reinforced concrete of a nuclear containment building

NASA Astrophysics Data System (ADS)

Philipose, K.; Shenton, B.

2011-04-01

The Containment Buildings of CANDU Nuclear Generating Stations were designed to house nuclear reactors and process equipment and also to provide confinement of releases from a potential nuclear accident such as a Loss Of Coolant Accident (LOCA). To meet this design requirement, a post-tensioning system was designed to induce compressive stresses in the structure to counteract the internal design pressure. The CANDU reactor building at Gentilly-1 (G-1), Quebec, Canada (250 MWe) was built in the early 1970s and is currently in a decommissioned state. The structure at present is under surveillance and monitoring. In the year 2000, a field investigation was conducted as part of a condition assessment and corrosion was detected in some of the grouted post-tension cable strands. However, no further work was done at that time to determine the cause, nature, impact and extent of the corrosion. An investigation of the Gentilly-1 containment building is currently underway to assess the condition of grouted post-tensioning cables and reinforced concrete. At two selected locations, concrete and steel reinforcements were removed from the containment building wall to expose horizontal cables. Individual cable strands and reinforcement bars were instrumented and measurements were taken in-situ before removing them for forensic examination and destructive testing to determine the impact of ageing and corrosion. Concrete samples were also removed and tested in a laboratory. The purpose of the field investigation and laboratory testing, using this structure as a test bed, was also to collect material ageing data and to develop potential Nondestructive Examination (NDE) methods to monitor Containment Building Integrity. The paper describes the field work conducted and the test results obtained for concrete, reinforcement and post-tensioning cables.

Formation of Gaps at the Specimen-Bar Interfaces in Numerical Simulations of Compression Hopkinson Bar Tests on Soft, Nearly Incompressible Materials

DTIC Science & Technology

2010-09-01

history of the axial stress at the S-TB interface is qualitatively and quantitatively similar, with the times delayed by about 1 s (see figure 12). In...average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed...the specimen and sufficiently short rise times to the final strain rate, small gaps formed at both the specimen-incident bar and the specimen

High pressure/high temperature thermogravimetric apparatus. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Suuberg, E.M.

1999-12-01

The purpose of this instrumentation grant was to acquire a state-of-the-art, high pressure, high temperature thermogravimetric apparatus (HP/HT TGA) system for the study of the interactions between gases and carbonaceous solids for the purpose of solving problems related to coal utilization and applications of carbon materials. The instrument that we identified for this purpose was manufactured by DMT (Deutsche Montan Technologies)--Institute of Cokemaking and Coal Chemistry of Essen, Germany. Particular features of note include: Two reactors: a standard TGA reactor, capable of 1100 C at 100 bar; and a high temperature (HT) reactor, capable of operation at 1600 C andmore » 100 bar; A steam generator capable of generating steam to 100 bar; Flow controllers and gas mixing system for up to three reaction gases, plus a separate circuit for steam, and another for purge gas; and An automated software system for data acquisition and control. The HP/TP DMT-TGA apparatus was purchased in 1996 and installed and commissioned during the summer of 1996. The apparatus was located in Room 128 of the Prince Engineering Building at Brown University. A hydrogen alarm and vent system were added for safety considerations. The system has been interfaced to an Ametek quadruple mass spectrometer (MA 100), pumped by a Varian V250 turbomolecular pump, as provided for in the original proposed. With this capability, a number of gas phase species of interest can be monitored in a near-simultaneous fashion. The MS can be used in a few different modes. During high pressure, steady-state gasification experiments, it is used to sample, measure, and monitor the reactant/product gases. It can also be used to monitor gas phase species during nonisothermal temperature programmed reaction (TPR) or temperature programmed desorption (TPD) experiments.« less

Fracture toughness of brittle materials determined with chevron notch specimens

NASA Technical Reports Server (NTRS)

Shannon, J. L., Jr.; Bursey, R. T.; Munz, D.; Pierce, W. S.

1980-01-01

The use of chevron-notch specimens for determining the plane strain fracture toughness (K sub Ic) of brittle materials is discussed. Three chevron-notch specimens were investigated: short bar, short rod, and four-point-bend. The dimensionless stress intensity coefficient used in computing K sub Ic is derived for the short bar specimen from the superposition of ligament-dependent and ligament-independent solutions for the straight through crack, and also from experimental compliance calibrations. Coefficients for the four-point-bend specimen were developed by the same superposition procedure, and with additional refinement using the slice model of Bluhm. Short rod specimen stress intensity coefficients were determined only by experimental compliance calibration. Performance of the three chevron-notch specimens and their stress intensity factor relations were evaluated by tests on hot-pressed silicon nitride and sintered aluminum oxide. Results obtained with the short bar and the four-point-bend specimens on silicon nitride are in good agreement and relatively free of specimen geometry and size effects within the range investigated. Results on aluminum oxide were affected by specimen size and chevron-notch geometry, believed due to a rising crack growth resistance curve for the material. Only the results for the short bar specimen are presented in detail.

Experimental and Theoretical Investigations on Bond Strength of GFRP Rebars in Normal and High Strength Concrete

NASA Astrophysics Data System (ADS)

Eswanth, P.; Dhinakaran, G.

2017-07-01

Bond behavior between GFRP bars and concrete is the most important parameter for constructing corrosion free structures by implementing the material. Serviceability of reinforced concrete structures are controlled by bond behavior. GFRP materials behave differently from reinforcing steel in terms of bond. They are of non-homogeneous and anisotropic. Due to this outstanding behavior, there is a difference in transfer of loads between GFRP bars and concrete which made it as an idealized choice of a material. In the present work, the bond strength of GFRP bars in normal and high strength concrete was studied. In total, 12 specimens containing 12 mm, 16 mm diameter rebars which were embedded in 150 mm x 150 mm x 150 mm cubes were investigated. The specimens were subjected to direct tension pull out test in accordance with IS 2770 part 1. The comparison of bond properties of GFRP rebar in normal and high strength concrete showed that pull out load of non-metallic rebar fell well within the range.

An Insertable Passive LC Pressure Sensor Based on an Alumina Ceramic for In Situ Pressure Sensing in High-Temperature Environments.

PubMed

Xiong, Jijun; Li, Chen; Jia, Pinggang; Chen, Xiaoyong; Zhang, Wendong; Liu, Jun; Xue, Chenyang; Tan, Qiulin

2015-08-31

Pressure measurements in high-temperature applications, including compressors, turbines, and others, have become increasingly critical. This paper proposes an implantable passive LC pressure sensor based on an alumina ceramic material for in situ pressure sensing in high-temperature environments. The inductance and capacitance elements of the sensor were designed independently and separated by a thermally insulating material, which is conducive to reducing the influence of the temperature on the inductance element and improving the quality factor of the sensor. In addition, the sensor was fabricated using thick film integrated technology from high-temperature materials that ensure stable operation of the sensor in high-temperature environments. Experimental results showed that the sensor accurately monitored pressures from 0 bar to 2 bar at temperatures up to 800 °C. The sensitivity, linearity, repeatability error, and hysteretic error of the sensor were 0.225 MHz/bar, 95.3%, 5.5%, and 6.2%, respectively.

An Insertable Passive LC Pressure Sensor Based on an Alumina Ceramic for In Situ Pressure Sensing in High-Temperature Environments

PubMed Central

Xiong, Jijun; Li, Chen; Jia, Pinggang; Chen, Xiaoyong; Zhang, Wendong; Liu, Jun; Xue, Chenyang; Tan, Qiulin

2015-01-01

Pressure measurements in high-temperature applications, including compressors, turbines, and others, have become increasingly critical. This paper proposes an implantable passive LC pressure sensor based on an alumina ceramic material for in situ pressure sensing in high-temperature environments. The inductance and capacitance elements of the sensor were designed independently and separated by a thermally insulating material, which is conducive to reducing the influence of the temperature on the inductance element and improving the quality factor of the sensor. In addition, the sensor was fabricated using thick film integrated technology from high-temperature materials that ensure stable operation of the sensor in high-temperature environments. Experimental results showed that the sensor accurately monitored pressures from 0 bar to 2 bar at temperatures up to 800 °C. The sensitivity, linearity, repeatability error, and hysteretic error of the sensor were 0.225 MHz/bar, 95.3%, 5.5%, and 6.2%, respectively. PMID:26334279

Efficiently mapping structure-property relationships of gas adsorption in porous materials: application to Xe adsorption.

PubMed

Kaija, A R; Wilmer, C E

2017-09-08

Designing better porous materials for gas storage or separations applications frequently leverages known structure-property relationships. Reliable structure-property relationships, however, only reveal themselves when adsorption data on many porous materials are aggregated and compared. Gathering enough data experimentally is prohibitively time consuming, and even approaches based on large-scale computer simulations face challenges. Brute force computational screening approaches that do not efficiently sample the space of porous materials may be ineffective when the number of possible materials is too large. Here we describe a general and efficient computational method for mapping structure-property spaces of porous materials that can be useful for adsorption related applications. We describe an algorithm that generates random porous "pseudomaterials", for which we calculate structural characteristics (e.g., surface area, pore size and void fraction) and also gas adsorption properties via molecular simulations. Here we chose to focus on void fraction and Xe adsorption at 1 bar, 5 bar, and 10 bar. The algorithm then identifies pseudomaterials with rare combinations of void fraction and Xe adsorption and mutates them to generate new pseudomaterials, thereby selectively adding data only to those parts of the structure-property map that are the least explored. Use of this method can help guide the design of new porous materials for gas storage and separations applications in the future.

Alternative Fuels Data Center: Workplace Charging Success: lynda.com

Science.gov Websites

installed its first on-site PEV charger - a "Juice Bar" with two Level 2 and two Level 1 outlets Francisco, which is housed in a LEED certified building that offers two charging stations. As lynda.com adds

GENERAL VIEW OF WESTERN PART OF PLANT INCLUDING (LEFT TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

GENERAL VIEW OF WESTERN PART OF PLANT INCLUDING (LEFT TO RIGHT) BETHLEHEM RAIL MILL, GENERAL OFFICE BUILDING, MACHINE SHOP, BAR MILL, BLOOMING MILL & OPEN HEARTH PLANT. - Pittsburgh Steel Company, Monessen Works, Open Hearth Plant, Donner Avenue, Monessen, Westmoreland County, PA

Extreme Water Loss and Abiotic O2 Buildup on Planets Throughout the Habitable Zones of M Dwarfs

PubMed Central

Barnes, R.

2015-01-01

Abstract We show that terrestrial planets in the habitable zones of M dwarfs older than ∼1 Gyr could have been in runaway greenhouses for several hundred million years following their formation due to the star's extended pre-main sequence phase, provided they form with abundant surface water. Such prolonged runaway greenhouses can lead to planetary evolution divergent from that of Earth. During this early runaway phase, photolysis of water vapor and hydrogen/oxygen escape to space can lead to the loss of several Earth oceans of water from planets throughout the habitable zone, regardless of whether the escape is energy-limited or diffusion-limited. We find that the amount of water lost scales with the planet mass, since the diffusion-limited hydrogen escape flux is proportional to the planet surface gravity. In addition to undergoing potential desiccation, planets with inefficient oxygen sinks at the surface may build up hundreds to thousands of bar of abiotically produced O2, resulting in potential false positives for life. The amount of O2 that builds up also scales with the planet mass; we find that O2 builds up at a constant rate that is controlled by diffusion: ∼5 bar/Myr on Earth-mass planets and up to ∼25 bar/Myr on super-Earths. As a result, some recently discovered super-Earths in the habitable zone such as GJ 667Cc could have built up as many as 2000 bar of O2 due to the loss of up to 10 Earth oceans of water. The fate of a given planet strongly depends on the extreme ultraviolet flux, the duration of the runaway regime, the initial water content, and the rate at which oxygen is absorbed by the surface. In general, we find that the initial phase of high luminosity may compromise the habitability of many terrestrial planets orbiting low-mass stars. Key Words: Astrobiology—Biosignatures—Extrasolar terrestrial planets—Habitability—Planetary atmospheres. Astrobiology 15, 119–143. PMID:25629240

kW-class diode laser bars

NASA Astrophysics Data System (ADS)

Strohmaier, S. G.; Erbert, G.; Meissner-Schenk, A. H.; Lommel, M.; Schmidt, B.; Kaul, T.; Karow, M.; Crump, P.

2017-02-01

Progress will be presented on ongoing research into the development of ultra-high power and efficiency bars achieving significantly higher output power, conversion efficiency and brightness than currently commercially available. We combine advanced InAlGaAs/GaAs-based epitaxial structures and novel lateral designs, new materials and superior cooling architectures to enable improved performance. Specifically, we present progress in kilowatt-class 10-mm diode laser bars, where recent studies have demonstrated 880 W continuous wave output power from a 10 mm x 4 mm laser diode bar at 850 A of electrical current and 15°C water temperature. This laser achieves < 60% electro-optical efficiency at 880 W CW output power.

F-BAR family proteins, emerging regulators for cell membrane dynamic changes-from structure to human diseases.

PubMed

Liu, Suxuan; Xiong, Xinyu; Zhao, Xianxian; Yang, Xiaofeng; Wang, Hong

2015-05-09

Eukaryotic cell membrane dynamics change in curvature during physiological and pathological processes. In the past ten years, a novel protein family, Fes/CIP4 homology-Bin/Amphiphysin/Rvs (F-BAR) domain proteins, has been identified to be the most important coordinators in membrane curvature regulation. The F-BAR domain family is a member of the Bin/Amphiphysin/Rvs (BAR) domain superfamily that is associated with dynamic changes in cell membrane. However, the molecular basis in membrane structure regulation and the biological functions of F-BAR protein are unclear. The pathophysiological role of F-BAR protein is unknown. This review summarizes the current understanding of structure and function in the BAR domain superfamily, classifies F-BAR family proteins into nine subfamilies based on domain structure, and characterizes F-BAR protein structure, domain interaction, and functional relevance. In general, F-BAR protein binds to cell membrane via F-BAR domain association with membrane phospholipids and initiates membrane curvature and scission via Src homology-3 (SH3) domain interaction with its partner proteins. This process causes membrane dynamic changes and leads to seven important cellular biological functions, which include endocytosis, phagocytosis, filopodium, lamellipodium, cytokinesis, adhesion, and podosome formation, via distinct signaling pathways determined by specific domain-binding partners. These cellular functions play important roles in many physiological and pathophysiological processes. We further summarize F-BAR protein expression and mutation changes observed in various diseases and developmental disorders. Considering the structure feature and functional implication of F-BAR proteins, we anticipate that F-BAR proteins modulate physiological and pathophysiological processes via transferring extracellular materials, regulating cell trafficking and mobility, presenting antigens, mediating extracellular matrix degradation, and transmitting signaling for cell proliferation.

Neutron spectroscopic study of crystal field excitations in Tb 2Ti 2O 7 and Tb 2Sn 2O 7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, J.; Fritsch, Katharina; Hao, Z.

2014-04-01

We present time-of-flight inelastic neutron scattering measurements at low temperature on powder samples of the magnetic pyrochlore oxides Tb 2Ti 2O 7 and Tb 2Sn 2O 7. These two materials possess related, but different ground states, with Tb 2Sn 2O 7 displaying "soft" spin ice order below T N approx 0.87 K, while Tb 2Ti 2O 7 enters a hybrid, glassy-spin ice state below T g approx 0.2 K. Our neutron measurements, performed at T = 1.5 K and 30 K, probe the crystal field states associated with the J = 6 states of Tb 3+ within the appropriate Fd3-barmmore » pyrochlore environment. These crystal field states determine the size and anisotropy of the Tb 3+ magnetic moment in each material's ground state, information that is an essential starting point for any description of the low temperature phase behavior and spin dynamics in Tb 2Ti 2O 7 and Tb 2Sn 2O 7. While these two materials have much in common, the cubic stanate lattice is expanded compared to the cubic titanate lattice. As our measurements show, this translates into a factor of approx 2 increase in the crystal field bandwidth of the 2J +1 = 13 states in Tb 2Ti 2O 7 compared with Tb 2Sn 2O 7. Our results are consistent with previous measurements on crystal field states in Tb 2Sn 2O 7, wherein the ground state doublet corresponds primarily to mJ = {vert_bar}+-5> and the first excited state doublet to mJ = {vert_bar}+-4>. In contrast, our results on Tb 2Ti 2O 7 differ markedly from earlier studies, showing that the ground state doublet corresponds to a significant mixture of mJ = {vert_bar}+-5>, mJ = {vert_bar}+-4> and mJ = {vert_bar}+-2>, while the first excited state doublet corresponds to a mixture of mJ = {vert_bar}+-4>, mJ = {vert_bar}+-5> and mJ = {vert_bar}+-1>. We discuss these results in the context of proposed mechanisms for the failure of Tb 2Ti 2O 7 to develop conventional long range order down to 50 mK.« less

Advancements in high-power diode laser stacks for defense applications

NASA Astrophysics Data System (ADS)

Pandey, Rajiv; Merchen, David; Stapleton, Dean; Patterson, Steve; Kissel, Heiko; Fassbender, Wilhlem; Biesenbach, Jens

2012-06-01

This paper reports on the latest advancements in vertical high-power diode laser stacks using micro-channel coolers, which deliver the most compact footprint, power scalability and highest power/bar of any diode laser package. We present electro-optical (E-O) data on water-cooled stacks with wavelengths ranging from 7xx nm to 9xx nm and power levels of up to 5.8kW, delivered @ 200W/bar, CW mode, and a power-conversion efficiency of >60%, with both-axis collimation on a bar-to-bar pitch of 1.78mm. Also, presented is E-O data on a compact, conductively cooled, hardsoldered, stack package based on conventional CuW and AlN materials, with bar-to-bar pitch of 1.8mm, delivering average power/bar >15W operating up to 25% duty cycle, 10ms pulses @ 45C. The water-cooled stacks can be used as pump-sources for diode-pumped alkali lasers (DPALs) or for more traditional diode-pumped solid-state lasers (DPSSL). which are power/brightness scaled for directed energy weapons applications and the conductively-cooled stacks as illuminators.

DOE-2 sample run book: Version 2.1E

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winkelmann, F.C.; Birdsall, B.E.; Buhl, W.F.

1993-11-01

The DOE-2 Sample Run Book shows inputs and outputs for a variety of building and system types. The samples start with a simple structure and continue to a high-rise office building, a medical building, three small office buildings, a bar/lounge, a single-family residence, a small office building with daylighting, a single family residence with an attached sunspace, a ``parameterized`` building using input macros, and a metric input/output example. All of the samples use Chicago TRY weather. The main purpose of the Sample Run Book is instructional. It shows the relationship of LOADS-SYSTEMS-PLANT-ECONOMICS inputs, displays various input styles, and illustrates manymore » of the basic and advanced features of the program. Many of the sample runs are preceded by a sketch of the building showing its general appearance and the zoning used in the input. In some cases we also show a 3-D rendering of the building as produced by the program DrawBDL. Descriptive material has been added as comments in the input itself. We find that a number of users have loaded these samples onto their editing systems and use them as ``templates`` for creating new inputs. Another way of using them would be to store various portions as files that can be read into the input using the {number_sign}{number_sign} include command, which is part of the Input Macro feature introduced in version DOE-2.lD. Note that the energy rate structures here are the same as in the DOE-2.lD samples, but have been rewritten using the new DOE-2.lE commands and keywords for ECONOMICS. The samples contained in this report are the same as those found on the DOE-2 release files. However, the output numbers that appear here may differ slightly from those obtained from the release files. The output on the release files can be used as a check set to compare results on your computer.« less

Finite Element Analysis of IPS Empress II Ceramic Bridge Reinforced by Zirconia Bar

PubMed Central

Kermanshah, H.; Bitaraf, T.; Geramy, A.

2012-01-01

Objective: The aim of this study was to determine the effect of trenched zirconia bar on the von Mises stress distribution of IPS –Empress II core ceramics. Materials and Methods: The three-dimensional model including a three-unit bridge from the second premolar to the second molar was designed. The model was reinforced with zirconia bar (ZB), zirconia bar with vertical trench (VZB) and zirconia bar with horizontal trench (HZB) (cross sections of these bars were circular). The model without zirconia bar was designed as the control. The bridges were loaded by 200 N and 500 N on the occlusal surface at the middle of the pontic component and von Mises stresses were evaluated along a defined path. Results: In the connector area, von Mises stress in MPa were approximately identical in the specimens with ZB (at molar connector (MC): 4.75 and at premolar connector (PC): 6.40) and without ZB (MC: 5.50, PC: 6.68), and considerable differences were not recognized. Whereas, Von-Mises stress (MPa) in the specimens with horizontal trenched Zirconia bar (HZB) (MC: 3.91, PC: 2.44) and Vertical trenched Zirconia bar (VZB) (MC: 2.53, PC: 2.56) was decreased considerably. Conclusion: Embeded trenched zirconia bar could reinforce IPS-Empress II at the connector area which is a main failure region in all ceramic fixed partial dentures. PMID:23323181

Observational constraints to boxy/peanut bulge formation time

NASA Astrophysics Data System (ADS)

Pérez, I.; Martínez-Valpuesta, I.; Ruiz-Lara, T.; de Lorenzo-Caceres, A.; Falcón-Barroso, J.; Florido, E.; González Delgado, R. M.; Lyubenova, M.; Marino, R. A.; Sánchez, S. F.; Sánchez-Blázquez, P.; van de Ven, G.; Zurita, A.

2017-09-01

Boxy/peanut bulges are considered to be part of the same stellar structure as bars and both could be linked through the buckling instability. The Milky Way is our closest example. The goal of this Letter is to determine if the mass assembly of the different components leaves an imprint in their stellar populations allowing the estimation the time of bar formation and its evolution. To this aim, we use integral field spectroscopy to derive the stellar age distributions, SADs, along the bar and disc of NGC 6032. The analysis clearly shows different SADs for the different bar areas. There is an underlying old (≥12 Gyr) stellar population for the whole galaxy. The bulge shows star formation happening at all times. The inner bar structure shows stars of ages older than 6 Gyr with a deficit of younger populations. The outer bar region presents an SAD similar to that of the disc. To interpret our results, we use a generic numerical simulation of a barred galaxy. Thus, we constrain, for the first time, the epoch of bar formation, the buckling instability period and the posterior growth from disc material. We establish that the bar of NGC 6032 is old, formed around 10 Gyr ago while the buckling phase possibly happened around 8 Gyr ago. All these results point towards bars being long-lasting even in the presence of gas.

77 FR 77016 - Foreign-Trade Zone 33 - Pittsburgh, Pennsylvania Notification of Proposed Export Production...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Confectionery Bars) Pittsburgh, PA Tsudis Chocolate Company (Tsudis), an operator of FTZ 33, submitted a... the facility would involve the production of chocolate confectionery bars for export (no shipments for... markets, FTZ procedures could exempt Tsudis from customs duty payments on the foreign status material used...

Parabolic trough solar collector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eaton, J.H.

1985-01-15

A parabolic trough solar collector using reflective flexible materials is disclosed. A parabolic cylinder mirror is formed by stretching a flexible reflecting material between two parabolic end formers. The formers are held in place by a spreader bar. The resulting mirror is made to track the sun, focusing the sun's rays on a receiver tube. The ends of the reflective material are attached by glue or other suitable means to attachment straps. The flexible mirror is then attached to the formers. The attachment straps are mounted in brackets and tensioned by tightening associated nuts on the ends of the attachmentmore » straps. This serves both to stretch the flexible material orthogonal to the receiver tube and to hold the flexible material on the formers. The flexible mirror is stretched in the direction of the receiver tube by adjusting tensioning nuts. If materials with matching coefficients of expansion for temperature and humidity have been chosen, for example, aluminum foil for the flexible mirror and aluminum for the spreader bar, the mirror will stay in adjustment through temperature and humidity excursions. With dissimilar materials, e.g., aluminized mylar or other polymeric material and steel, spacers can be replaced with springs to maintain proper adjustment. The spreader bar cross section is chosen to be in the optic shadow of the receiver tube when tracking and not to intercept rays of the sun that would otherwise reach the receiver tube. This invention can also be used to make non-parabolic mirrors for other apparatus and applications.« less

Finite Element Simulations to Explore Assumptions in Kolsky Bar Experiments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crum, Justin

2015-08-05

The chief purpose of this project has been to develop a set of finite element models that attempt to explore some of the assumptions in the experimental set-up and data reduction of the Kolsky bar experiment. In brief, the Kolsky bar, sometimes referred to as the split Hopkinson pressure bar, is an experimental apparatus used to study the mechanical properties of materials at high strain rates. Kolsky bars can be constructed to conduct experiments in tension or compression, both of which are studied in this paper. The basic operation of the tension Kolsky bar is as follows: compressed air ismore » inserted into the barrel that contains the striker; the striker accelerates towards the left and strikes the left end of the barrel producing a tensile stress wave that propogates first through the barrel and then down the incident bar, into the specimen, and finally the transmission bar. In the compression case, the striker instead travels to the right and impacts the incident bar directly. As the stress wave travels through an interface (e.g., the incident bar to specimen connection), a portion of the pulse is transmitted and the rest reflected. The incident pulse, as well as the transmitted and reflected pulses are picked up by two strain gauges installed on the incident and transmitted bars as shown. By interpreting the data acquired by these strain gauges, the stress/strain behavior of the specimen can be determined.« less

Modeling And Simulation Of Bar Code Scanners Using Computer Aided Design Software

NASA Astrophysics Data System (ADS)

Hellekson, Ron; Campbell, Scott

1988-06-01

Many optical systems have demanding requirements to package the system in a small 3 dimensional space. The use of computer graphic tools can be a tremendous aid to the designer in analyzing the optical problems created by smaller and less costly systems. The Spectra Physics grocery store bar code scanner employs an especially complex 3 dimensional scan pattern to read bar code labels. By using a specially written program which interfaces with a computer aided design system, we have simulated many of the functions of this complex optical system. In this paper we will illustrate how a recent version of the scanner has been designed. We will discuss the use of computer graphics in the design process including interactive tweaking of the scan pattern, analysis of collected light, analysis of the scan pattern density, and analysis of the manufacturing tolerances used to build the scanner.

Application of photon Doppler velocimetry to direct impact Hopkinson pressure bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lea, Lewis J., E-mail: ll379@cam.ac.uk; Jardine, Andrew P.

2016-02-15

Direct impact Hopkinson pressure bar systems offer many potential advantages over split Hopkinson pressure bars, including access to higher strain rates, higher strains for equivalent striker velocity and system length, lower dispersion, and faster achievement of force equilibrium. Currently, these advantages are gained at the expense of all information about the striker impacted specimen face, preventing the experimental determination of force equilibrium, and requiring approximations to be made on the sample deformation history. In this paper, we discuss an experimental method and complementary data analysis for using photon Doppler velocimetry to measure surface velocities of the striker and output barsmore » in a direct impact bar experiment, allowing similar data to be recorded as in a split bar system. We discuss extracting velocity and force measurements, and the precision of measurements. Results obtained using the technique are compared to equivalent split bar tests, showing improved stress measurements for the lowest and highest strains in fully dense metals, and improvement for all strains in slow and non-equilibrating materials.« less

Dynamic behavior of geometrically complex hybrid composite samples in a Split-Hopkinson Pressure Bar system

NASA Astrophysics Data System (ADS)

Pouya, M.; Balasubramaniam, S.; Sharafiev, S.; F-X Wagner, M.

2018-06-01

The interfaces between layered materials play an important role for the overall mechanical behavior of hybrid composites, particularly during dynamic loading. Moreover, in complex-shaped composites, interfacial failure is strongly affected by the geometry and size of these contact interfaces. As preliminary work for the design of a novel sample geometry that allows to analyze wave reflection phenomena at the interfaces of such materials, a series of experiments using a Split-Hopkinson Pressure Bar technique was performed on five different sample geometries made of a monomaterial steel. A complementary explicit finite element model of the Split-Hopkinson Pressure Bar system was developed and the same sample geometries were studied numerically. The simulated input, reflected and transmitted elastic wave pulses were analyzed for the different sample geometries and were found to agree well with the experimental results. Additional simulations using different composite layers of steel and aluminum (with the same sample geometries) were performed to investigate the effect of material variation on the propagated wave pulses. The numerical results show that the reflected and transmitted wave pulses systematically depend on the sample geometry, and that elastic wave pulse propagation is affected by the properties of individual material layers.

Dynamic characterization and modeling of potting materials for electronics assemblies

NASA Astrophysics Data System (ADS)

Joshi, Vasant S.; Lee, Gilbert F.; Santiago, Jaime R.

2017-01-01

Prediction of survivability of encapsulated electronic components subject to impact relies on accurate modeling, which in turn needs both static and dynamic characterization of individual electronic components and encapsulation material to generate reliable material parameters for a robust material model. Current focus is on potting materials to mitigate high rate loading on impact. In this effort, difficulty arises in capturing one of the critical features characteristic of the loading environment in a high velocity impact: multiple loading events coupled with multi-axial stress states. Hence, potting materials need to be characterized well to understand its damping capacity at different frequencies and strain rates. An encapsulation scheme to protect electronic boards consists of multiple layers of filled as well as unfilled polymeric materials like Sylgard 184 and Trigger bond Epoxy # 20-3001. A combination of experiments conducted for characterization of materials used Split Hopkinson Pressure Bar (SHPB), and dynamic material analyzer (DMA). For material which behaves in an ideal manner, a master curve can be fitted to Williams-Landel-Ferry (WLF) model. To verify the applicability of WLF model, a new temperature-time shift (TTS) macro was written to compare idealized temperature shift factor with experimental incremental shift factor. Deviations can be readily observed by comparison of experimental data with the model fit to determine if model parameters reflect the actual material behavior. Similarly, another macro written for obtaining Ogden model parameter from Hopkinson Bar tests can readily indicate deviations from experimental high strain rate data. Experimental results for different materials used for mitigating impact, and ways to combine data from DMA and Hopkinson bar together with modeling refinements are presented.

Mg2+ Doped into Electro-synthesized HKUST-1 and Their Initial Hydrogen Sorption Properties

NASA Astrophysics Data System (ADS)

Lestari, W. W.; Ni'maturrohmah, D.; Arrozi, U. S. F.; Suwarno, H.

2018-01-01

The hydrogen storage materials are essentially play important roles in supporting the utilization of hydrogen as a promising alternative energy. Several innovative materials have been proposed and intensively investigated in this regard, including Metal-Organic Framework (MOFs). MOFs type HKUST-1 [Cu3(BTC)2] (BTC = benzene-tri-carboxylate) is the most explored materials in hydrogen storage. In this research, HKUST-1 was electro-synthesized under 15 volt for 1.5 h. This material was ex-situ modified with magnesium(II) ion with variation: 3, 5 and 10 wt% to add attractive sites for hydrogen to form Mg2+@HKUST-1. The final materials were characterized by XRD, FTIR, SEM-EDX, and SAA. Hydrogen sorption measurement was conducted using Sievert system at 30 and 80 °C with pressure from 0.2 to 1.5 bar in 10 minutes for each condition. According to XRD analysis, the basic structure of Mg2+@HKUST-1 was remaining stable. In contrary, SEM analysis showed that HKUST-1 morphology was changed after modification with Mg2+. In addition, the surface area of materials significantly increased from 372.112 to 757.617m2/g, based on SAA analysis. The presence of Mg2+ in the HKUST-1 increased the hydrogen sorption capacity up to 0.475 wt% at 1.4 bar at 30 °C and 0.256 wt% at 80 °C (1.4 bar).

Graphene-based porous materials with tunable surface area and CO2 adsorption properties synthesized by fluorine displacement reaction with various diamines.

PubMed

Li, Baoyin; Fan, Kun; Ma, Xin; Liu, Yang; Chen, Teng; Cheng, Zheng; Wang, Xu; Jiang, Jiaxing; Liu, Xiangyang

2016-09-15

A mild, operationally simple and controllable protocol for preparing graphene-based porous materials is essential to achieve a good pore-design development. In this paper, graphene-based porous materials with tunable surface area were constructed by the intercalation of fluorinated graphene (FG) based on the reaction of reactive CF bonds attached to graphene sheets with various amine-terminated molecules. In the porous materials, graphene sheets are like building blocks, and the diamines covalently grafted onto graphene framework act as pillars. Various diamines are successfully grafted onto graphene sheets, but the grafting ratio of diamines and reduction degree of FG differ greatly and depend on the chemical reactivity of diamines. Pillared diamine molecules chemically anchor at one end and are capable of undergoing a different reaction on the other end, resulting in three different conformations of graphene derivatives. Nitrogen sorption isotherms revealed that the surface area and pore distribution of the obtained porous materials depend heavily on the size and structure of diamine pillars. CO2 uptake capacity characterization showed that ethylenediamine intercalated FG achieved a high CO2 uptake density of 18.0 CO2 molecules per nm(2) at 0°C and 1.1bars, and high adsorption heat, up to 46.1kJmol(-1) at zero coverage. Copyright © 2016 Elsevier Inc. All rights reserved.

How curvature-generating proteins build scaffolds on membrane nanotubes

PubMed Central

Evergren, Emma; Golushko, Ivan; Prévost, Coline; Renard, Henri-François; Johannes, Ludger; McMahon, Harvey T.; Lorman, Vladimir; Voth, Gregory A.; Bassereau, Patricia

2016-01-01

Bin/Amphiphysin/Rvs (BAR) domain proteins control the curvature of lipid membranes in endocytosis, trafficking, cell motility, the formation of complex subcellular structures, and many other cellular phenomena. They form 3D assemblies that act as molecular scaffolds to reshape the membrane and alter its mechanical properties. It is unknown, however, how a protein scaffold forms and how BAR domains interact in these assemblies at protein densities relevant for a cell. In this work, we use various experimental, theoretical, and simulation approaches to explore how BAR proteins organize to form a scaffold on a membrane nanotube. By combining quantitative microscopy with analytical modeling, we demonstrate that a highly curving BAR protein endophilin nucleates its scaffolds at the ends of a membrane tube, contrary to a weaker curving protein centaurin, which binds evenly along the tube’s length. Our work implies that the nature of local protein–membrane interactions can affect the specific localization of proteins on membrane-remodeling sites. Furthermore, we show that amphipathic helices are dispensable in forming protein scaffolds. Finally, we explore a possible molecular structure of a BAR-domain scaffold using coarse-grained molecular dynamics simulations. Together with fluorescence microscopy, the simulations show that proteins need only to cover 30–40% of a tube’s surface to form a rigid assembly. Our work provides mechanical and structural insights into the way BAR proteins may sculpt the membrane as a high-order cooperative assembly in important biological processes. PMID:27655892

Impact buckling of thin bars in the elastic range for any end condition

NASA Technical Reports Server (NTRS)

Taub, Josef

1934-01-01

Following a qualitative discussion of the complicated process involved in a short-period, longitudinal force applied to an originally not quite straight bar, the actual process is substituted by an idealized process for the purpose of analytical treatment. The simplifications are: the assumption of an infinitely high rate of propagation of the elastic longitudinal waves in the bar, limitation to slender bars, disregard of material damping and of rotatory inertia, the assumption of consistently small elastic deformations, the assumption of cross-sectional dimensions constant along the bar axis, the assumption of a shock-load constant in time, and the assumption of eccentricities on one plane. Then follow the mathematical principles for resolving the differential equation of the simplified problem, particularly the developability of arbitrary functions with steady first and second and intermittently steady third and fourth derivatives into one convergent series, according to the natural functions of the homogeneous differential equation.

A modified split Hopkinson pressure bar for toughness tests

NASA Astrophysics Data System (ADS)

Granier, N.; Grunenwald, T.

2006-08-01

In order to characterize material toughness or to study crack arrest under dynamic loading conditions, a new testing device has been developed at CEA/Valduc. A new Split Hopkinson Pressure Bar (SHPB) has been modified: it is now composed of a single incident bar and a double transmitter bar. With this facility, a notched specimen can be loaded under three points bending conditions. Qualification tests with titanium and steel notched samples are presented. Data treatment software has been adapted to estimate the sample deflection as a function of time and treat the energy balance. These results are compared with classical Charpy experiments. Effect of various contact areas between specimen and bars are studied to point out their influence on obtained measurements. The advantage of a “knife” contact compared to a plane one is then clearly demonstrated. All results obtained with this new testing device are in good agreement and show a reduced scattering.

Science Behind Bars: Reaching Inmates from Rikers Island

NASA Astrophysics Data System (ADS)

Mocsy, Agnes

2017-01-01

I report on the project ``Science Behind Bars: Reaching Inmates on Rikers Island'' partially funded through an APS Public Outreach and Informing the Public grant. This project involves developing leave-behind materials and setting up meetings to speak with Rikers Island inmates about science, evidence-based reasoning, and the dangers of stereotype threat. APS Mini Grant.

High-power diode laser modules from 410 nm to 2200 nm

NASA Astrophysics Data System (ADS)

Köhler, Bernd; Kissel, Heiko; Flament, Marco; Wolf, Paul; Brand, Thomas; Biesenbach, Jens

2010-02-01

In this work we report on high-power diode laser modules covering a wide spectral range from 410 nm to 2200 nm. Driven by improvements in the technology of diode laser bars with non-standard wavelengths, such systems are finding a growing number of applications. Fields of application that benefit from these developments are direct medical applications, printing industry, defense technology, polymer welding and pumping of solid-sate lasers. Diode laser bars with standard wavelengths from 800 - 1000 nm are based on InGaAlAs, InGaAlP, GaAsP or InGaAs semiconductor material with an optical power of more than 100 W per bar. For shorter wavelengths from 630 - 690 nm InGaAlP semiconductor material is used with an optical power of about 5 W per bar. Extending the wavelength range beyond 1100 nm is realized by using InGaAs on InP substrates or with InAs quantum dots embedded in GaAs for wavelengths up to 1320 nm and (AlGaIn)(AsSb) for wavelengths up to 2200 nm. In these wavelength ranges the output power per bar is about 6 - 20 W. In this paper we present a detailed characterization of these diode laser bars, including measurements of power, spectral data and life time data. In addition, we will show different fiber coupled modules, ranging from 638 nm with 13 W output power (400 μm fiber, NA 0.22) up to 1940 nm with more than 50 W output power (600 μm fiber NA 0.22).

Defining the formative discharge for alternate bars in alluvial rivers

NASA Astrophysics Data System (ADS)

Redolfi, M.; Carlin, M.; Tubino, M.; Adami, L.; Zolezzi, G.

2017-12-01

We investigate the properties of alternate bars in long straight reaches of channelized streams subject to an unsteady, irregular flow regime. To this aim we propose a novel integration of a statistical approach with the analytical perturbation model of Tubino (1991) which predicts the evolution of bar properties (namely amplitude and wavelength) as consequence of a flood. The outcomes of our integrated modelling approach are probability distribution of the bar properties, which depend essentially on two ingredients: (i) the statistical properties of the flow regime (duration, frequency and magnitude of the flood events, and (ii) the reach-averaged hydro-geomorphic characteristics of the channel (bed material, channel gradient and width). This allows to define a "bar-forming" discharge value as the flow value which would reproduce the most likely bar properties in a river reach under unsteady flow. Alternate bars are often migrating downstream and growing or declining during flood events. The timescale of bar growth and migration is often comparable with the duration of the floods: consequently, bar properties such as height and wavelength do not respond instantaneously to discharge variations (i.e. quasi-equilibrium response) but may depend on previous flood events. Theoretical results are compared with observations in three Alpine, channelized gravel bed rivers with encouraging outcomes.

Modelling of Mechanical Behavior at High Strain Rate of Ti-6al-4v Manufactured By Means of Direct Metal Laser Sintering Technique

NASA Astrophysics Data System (ADS)

Iannitti, Gianluca; Bonora, Nicola; Gentile, Domenico; Ruggiero, Andrew; Testa, Gabriel; Gubbioni, Simone

2017-06-01

In this work, the mechanical behavior of Ti-6Al-4V obtained by additive manufacturing technique was investigated, also considering the build direction. Dog-bone shaped specimens and Taylor cylinders were machined from rods manufactured by means of the EOSSINT M2 80 machine, based on Direct Metal Laser Sintering technique. Tensile tests were performed at strain rate ranging from 5E-4 s-1 to 1000 s-1 using an Instron electromechanical machine for quasistatic tests and a Direct-Tension Split Hopkinson Bar for dynamic tests. The mechanical strength of the material was described by a Johnson-Cook model modified to account for stress saturation occurring at high strain. Taylor cylinder tests and their corresponding numerical simulations were carried out in order to validate the constitutive model under a complex deformation path, high strain rates, and high temperatures.

Improved silicon carbide for advanced heat engines

NASA Technical Reports Server (NTRS)

Whalen, T. J.; Winterbottom, W. L.

1986-01-01

Work performed to develop silicon carbide materials of high strength and to form components of complex shape and high reliability is described. A beta-SiC powder and binder system was adapted to the injection molding process and procedures and process parameters developed capable of providing a sintered silicon carbide material with improved properties. The initial effort has been to characterize the baseline precursor materials (beta silicon carbide powder and boron and carbon sintering aids), develop mixing and injection molding procedures for fabricating test bars, and characterize the properties of the sintered materials. Parallel studies of various mixing, dewaxing, and sintering procedures have been carried out in order to distinguish process routes for improving material properties. A total of 276 MOR bars of the baseline material have been molded, and 122 bars have been fully processed to a sinter density of approximately 95 percent. The material has a mean MOR room temperature strength of 43.31 ksi (299 MPa), a Weibull characteristic strength of 45.8 ksi (315 MPa), and a Weibull modulus of 8.0. Mean values of the MOR strengths at 1000, 1200, and 14000 C are 41.4, 43.2, and 47.2 ksi, respectively. Strength controlling flaws in this material were found to consist of regions of high porosity and were attributed to agglomerates originating in the initial mixing procedures. The mean stress rupture lift at 1400 C of five samples tested at 172 MPa (25 ksi) stress was 62 hours and at 207 MPa (30 ksi) stress was 14 hours. New fluid mixing techniques have been developed which significantly reduce flaw size and improve the strength of the material. Initial MOR tests indicate the strength of the fluid-mixed material exceeds the baseline property by more than 33 percent.

Highly reliable high-power AlGaAs/GaAs 808 nm diode laser bars

NASA Astrophysics Data System (ADS)

Hülsewede, R.; Schulze, H.; Sebastian, J.; Schröder, D.; Meusel, J.; Hennig, P.

2007-02-01

There are strong demands at the market to increase power and reliability for 808 nm diode laser bars. Responding to this JENOPTIK Diode Lab GmbH developed high performance 808 nm diode laser bars in the AlGaAs/GaAs material system with special emphasis to high power operation and long term stability. Optimization of the epitaxy structure and improvements in the diode laser bar design results in very high slope efficiency of >1.2 W/A, low threshold current and small beam divergence in slow axis direction. Including low serial resistance the overall wall plug efficiency is up to 65% for our 20%, 30% and 50% filling factor 10 mm diode laser bars. With the JENOPTIK Diode Lab cleaving and coating technique the maximum output power is 205 W in CW operation and 377 W in QCW operation (200 μs, 2% duty cycle) for bars with 50% filling factor. These bars mounted on micro channel cooled package are showing a very high reliability of >15.000 h. Mounted on conductive cooled package high power operation at 100 W is demonstrated for more than 5000h.

The dynamic properties behavior of high strength concrete under different strain rate

NASA Astrophysics Data System (ADS)

Abdullah, Hasballah; Husin, Saiful; Umar, Hamdani; Rizal, Samsul

2005-04-01

This paper present a number experimental data and numerical technique used in the dynamic behavior of high strength concrete. A testing device is presented for the experimental study of dynamic behavior material under high strain rates. The specimen is loaded by means of a high carbon steel Hopkinson pressure bar (40 mm diameter, 3000 mm long input bar and 1500 mm long out put bar) allowing for the testing of specimen diameter is large enough in relation to the size of aggregates. The other method also proposed for measuring tensile strength, the measurement method based on the superposition and concentration of tensile stress wave reflected both from the free-free ends of striking bar and the specimen bar. The compression Hopkinson bar test, the impact tensile test of high strength concrete bars are performed, together with compression static strength test. In addition, the relation between break position under finite element simulation and impact tensile strength are examined. The three-dimensional simulation of the specimen under transient loading are presented and comparisons between the experimental and numerical simulation on strain rate effects of constitutive law use in experimental are study.

History of the Pacific Ocean Division Corps of Engineers 1957-1967

DTIC Science & Technology

1972-01-01

mound barrier; designed by HED civil engineer Robert Q. Palmer, these concrete three-bar struc- tures provided a sturdy substitute for scarce rock...that metal buildings would require high main- tenance costs, while the termite problem eliminates construction in wood. Not only for these reasons

Organizing for Better School Food.

ERIC Educational Resources Information Center

Center for Science in the Public Interest, Washington, DC.

The ideal school cafeteria includes a salad bar and serving tables with healthy food items. Certain cafeteria pitfalls, such as a noisy or stuffy atmosphere, can be avoided by good administration. Specific guidelines on campaigning for better school food consist of building a community coalition that holds public meetings, learning about the…

The owl: spotted, listed, barred, or gone?

Treesearch

Sally Duncan

1998-01-01

The information we bring to the table is usually complex. The April issue of Science Findings illustrates this complexity. Scientific inquiry about an individual species and its habitat requires modeling, assumptions, and time. Uncertainty remains after studies are done. Once policy is made, implementation continues to build new understanding, which may present...

Developing material for promoting problem-solving ability through bar modeling technique

NASA Astrophysics Data System (ADS)

Widyasari, N.; Rosiyanti, H.

2018-01-01

This study aimed at developing material for enhancing problem-solving ability through bar modeling technique with thematic learning. Polya’s steps of problem-solving were chosen as the basis of the study. The methods of the study were research and development. The subject of this study were five teen students of the fifth grade of Lab-school FIP UMJ elementary school. Expert review and student’ response analysis were used to collect the data. Furthermore, the data were analyzed using qualitative descriptive and quantitative. The findings showed that material in theme “Selalu Berhemat Energi” was categorized as valid and practical. The validity was measured by using the aspect of language, contents, and graphics. Based on the expert comments, the materials were easy to implement in the teaching-learning process. In addition, the result of students’ response showed that material was both interesting and easy to understand. Thus, students gained more understanding in learning problem-solving.

K-band observations of boxy bulges - I. Morphology and surface brightness profiles

NASA Astrophysics Data System (ADS)

Bureau, M.; Aronica, G.; Athanassoula, E.; Dettmar, R.-J.; Bosma, A.; Freeman, K. C.

2006-08-01

In this first paper of a series on the structure of boxy and peanut-shaped (B/PS) bulges, Kn-band observations of a sample of 30 edge-on spiral galaxies are described and discussed. Kn-band observations best trace the dominant luminous galactic mass and are minimally affected by dust. Images, unsharp-masked images, as well as major-axis and vertically summed surface brightness profiles are presented and discussed. Galaxies with a B/PS bulge tend to have a more complex morphology than galaxies with other bulge types, more often showing centred or off-centred X structures, secondary maxima along the major-axis and spiral-like structures. While probably not uniquely related to bars, those features are observed in three-dimensional N-body simulations of barred discs and may trace the main bar orbit families. The surface brightness profiles of galaxies with a B/PS bulge are also more complex, typically containing three or more clearly separated regions, including a shallow or flat intermediate region (Freeman Type II profiles). The breaks in the profiles offer evidence for bar-driven transfer of angular momentum and radial redistribution of material. The profiles further suggest a rapid variation of the scaleheight of the disc material, contrary to conventional wisdom but again as expected from the vertical resonances and instabilities present in barred discs. Interestingly, the steep inner region of the surface brightness profiles is often shorter than the isophotally thick part of the galaxies, itself always shorter than the flat intermediate region of the profiles. The steep inner region is also much more prominent along the major-axis than in the vertically summed profiles. Similarly to other recent work but contrary to the standard `bulge + disc' model (where the bulge is both thick and steep), we thus propose that galaxies with a B/PS bulge are composed of a thin concentrated disc (a disc-like bulge) contained within a partially thick bar (the B/PS bulge), itself contained within a thin outer disc. The inner disc likely formed secularly through bar-driven processes and is responsible for the steep inner region of the surface brightness profiles, traditionally associated with a classic bulge, while the bar is responsible for the flat intermediate region of the surface brightness profiles and the thick complex morphological structures observed. Those components are strongly coupled dynamically and are formed mostly of the same (disc) material, shaped by the weak but relentless action of the bar resonances. Any competing formation scenario for galaxies with a B/PS bulge, which represent at least 45 per cent of the local disc galaxy population, must explain equally well and self-consistently the above morphological and photometric properties, the complex gas and stellar kinematics observed, and the correlations between them.

77 FR 47595 - Stainless Steel Bar From Brazil, India, Japan, and Spain: Continuation of Antidumping Duty Orders

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-09

...-805] Stainless Steel Bar From Brazil, India, Japan, and Spain: Continuation of Antidumping Duty Orders... Brazil, India, Japan, and Spain would likely lead to a continuation or recurrence of dumping and material... Brazil, India, Japan, and Spain pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act...

The effect of stress and incentive magnetic field on the average volume of magnetic Barkhausen jump in iron

NASA Astrophysics Data System (ADS)

Shu, Di; Guo, Lei; Yin, Liang; Chen, Zhaoyang; Chen, Juan; Qi, Xin

2015-11-01

The average volume of magnetic Barkhausen jump (AVMBJ) v bar generated by magnetic domain wall irreversible displacement under the effect of the incentive magnetic field H for ferromagnetic materials and the relationship between irreversible magnetic susceptibility χirr and stress σ are adopted in this paper to study the theoretical relationship among AVMBJ v bar(magneto-elasticity noise) and the incentive magnetic field H. Then the numerical relationship among AVMBJ v bar, stress σ and the incentive magnetic field H is deduced. Utilizing this numerical relationship, the displacement process of magnetic domain wall for single crystal is analyzed and the effect of the incentive magnetic field H and the stress σ on the AVMBJ v bar (magneto-elasticity noise) is explained from experimental and theoretical perspectives. The saturation velocity of Barkhausen jump characteristic value curve is different when tensile or compressive stress is applied on ferromagnetic materials, because the resistance of magnetic domain wall displacement is different. The idea of critical magnetic field in the process of magnetic domain wall displacement is introduced in this paper, which solves the supersaturated calibration problem of AVMBJ - σ calibration curve.

Metal/polymer composite Nuss bar for minimally invasive bar removal after Pectus Excavatum treatment: FEM simulations.

PubMed

Ricotti, Leonardo; Ciuti, Gastone; Ghionzoli, Marco; Messineo, Antonio; Menciassi, Arianna

2014-12-01

This study aims at assessing the mechanical behavior of a composite metal/polymer bar to be implanted in the retrosternal position, in order to correct chest wall deformities, such as Pectus Excavatum. A 300-mm-long, 12.7-mm-wide, and 3.5-mm-thick Nuss bar was considered, made of different metals and biodegradable polymers, fixed at its extremities, and with a constant force of 250 N applied on its center. Two different geometries for the metal elements to be embedded in the polymeric matrix were tested: in the former, thin metal sheets and in the latter, cylindrical metal reinforcing rods were considered. Finite element method simulation results are reported, in terms of maximum stress and strain of the bar. Furthermore, the maximum stress values obtained by varying metal sheet thickness or rod diameter (and therefore the volumetric percentage of metal within the matrix) for different material combinations are also shown; optimal configuration for the Pectus Excavatum treatment was finally identified for a composite Nuss bar. Copyright © 2014 John Wiley & Sons, Ltd.

Radiochronological Age of a Uranium Metal Sample from an Abandoned Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyers, L A; Williams, R W; Glover, S E

2012-03-16

A piece of scrap uranium metal bar buried in the dirt floor of an old, abandoned metal rolling mill was analyzed using multi-collector inductively coupled plasma mass spectroscopy (MC-ICP-MS). The mill rolled uranium rods in the 1940s and 1950s. Samples of the contaminated dirt in which the bar was buried were also analyzed. The isotopic composition of uranium in the bar and dirt samples were both the same as natural uranium, though a few samples of dirt also contained recycled uranium; likely a result of contamination with other material rolled at the mill. The time elapsed since the uranium metalmore » bar was last purified can be determined by the in-growth of the isotope {sup 230}Th from the decay of {sup 234}U, assuming that only uranium isotopes were present in the bar after purification. The age of the metal bar was determined to be 61 years at the time of this analysis and corresponds to a purification date of July 1950 {+-} 1.5 years.« less

Resonant di-Higgs boson production in the b b ¯ W W channel: Probing the electroweak phase transition at the LHC

DOE PAGES

Huang, T.; No, J. M.; Pernié, L.; ...

2017-08-11

Here, we analyze the prospects for resonant di-Higgs production searches at the LHC in themore » $$b\\bar{b}$$W +W − (W +→ℓ +ν ℓ, W −→ℓ −$$\\bar{v}$$ ℓ) channel, as a probe of the nature of the electroweak phase transition in Higgs portal extensions of the Standard Model. In order to maximize the sensitivity in this final state, we develop a new algorithm for the reconstruction of the $$b\\bar{b}$$W +W − invariant mass in the presence of neutrinos from the W decays, building from a technique developed for the reconstruction of resonances decaying to τ +τ − pairs. We show that resonant di-Higgs production in the $$b\\bar{b}$$W +W − channel could be a competitive probe of the electroweak phase transition already with the data sets to be collected by the CMS and ATLAS experiments in run 2 of the LHC. The increase in sensitivity with larger amounts of data accumulated during the high-luminosity LHC phase can be sufficient to enable a potential discovery of the resonant di-Higgs production in this channel.« less

Resonant di-Higgs boson production in the b b ¯ W W channel: Probing the electroweak phase transition at the LHC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, T.; No, J. M.; Pernié, L.

Here, we analyze the prospects for resonant di-Higgs production searches at the LHC in themore » $$b\\bar{b}$$W +W − (W +→ℓ +ν ℓ, W −→ℓ −$$\\bar{v}$$ ℓ) channel, as a probe of the nature of the electroweak phase transition in Higgs portal extensions of the Standard Model. In order to maximize the sensitivity in this final state, we develop a new algorithm for the reconstruction of the $$b\\bar{b}$$W +W − invariant mass in the presence of neutrinos from the W decays, building from a technique developed for the reconstruction of resonances decaying to τ +τ − pairs. We show that resonant di-Higgs production in the $$b\\bar{b}$$W +W − channel could be a competitive probe of the electroweak phase transition already with the data sets to be collected by the CMS and ATLAS experiments in run 2 of the LHC. The increase in sensitivity with larger amounts of data accumulated during the high-luminosity LHC phase can be sufficient to enable a potential discovery of the resonant di-Higgs production in this channel.« less

Instrumentation for sensing moisture content of material using a transient thermal pulse

NASA Technical Reports Server (NTRS)

Yang, L. C. (Inventor)

1981-01-01

Instrumentation is developed for sensing moisture content of material using a transient thermal pulse and is comprised of a sensing probe having a sensing element in the form of a ribbon excited by a constant current pulse to increase the temperature, and therefore the resistance, of the ribbon linearly. Moisture in web material limits the increase of temperature during the pulse in proportion to the moisture content. This increase in temperature produces a proportional increase in resistivity which is measured with a Wheatsone bridge as a change in voltage displayed by a measurement display unit. The probe is glued in a shallow groove of a lucite bar and connected to copper pins embedded in the bar.

Absorption of infrared radiation by carbon monoxide at elevated temperatures and pressures: Part B. Total emissivity charts and correlations

NASA Astrophysics Data System (ADS)

Alberti, Michael; Weber, Roman; Mancini, Marco

2017-10-01

The line-by-line procedure developed in the associated paper (Part A ) has been used to generate the total emissivity chart for pure CO and CO -N2 /air mixtures at 1 bar total pressure, in the 300 to 3000 K temperature and 0.01 to 3000 bar cm pressure path length range. Methods of scaling the emissivity to pressures different to 1 bar, in the range 0.1 to 40 bar, are provided through pressure correction graphs and EXCEL interpolator (Supplementary Material). The interpolated emissivities are within ± 2% margin from the line-by-line calculated values. The newly developed emissivity graphs are substantially more accurate than the existing Ulrich (1936) & Hottel (1954) and Abu-Romia & Tien (1966) charts.

Advancements of ultra-high peak power laser diode arrays

NASA Astrophysics Data System (ADS)

Crawford, D.; Thiagarajan, P.; Goings, J.; Caliva, B.; Smith, S.; Walker, R.

2018-02-01

Enhancements of laser diode epitaxy in conjunction with process and packaging improvements have led to the availability of 1cm bars capable of over 500W peak power at near-infrared wavelengths (770nm to 1100nm). Advances in cooler design allow for multi-bar stacks with bar-to-bar pitches as low as 350μm and a scalable package architecture enabled a single diode assembly with total peak powers of over 1MegaWatt of peak power. With the addition of micro-optics, overall array brightness greater than 10kW/cm2 was achieved. Performance metrics of barbased diode lasers specifically engineered for high peak power and high brightness at wavelengths and pulse conditions commonly used to pump a variety of fiber and solid-state materials are presented.

Explosive Characteristics of Carbonaceous Nanoparticles

NASA Astrophysics Data System (ADS)

Turkevich, Leonid; Fernback, Joseph; Dastidar, Ashok

2013-03-01

Explosion testing has been performed on 20 codes of carbonaceous particles. These include SWCNTs (single-walled carbon nanotubes), MWCNTs (multi-walled carbon nanotubes), CNFs (carbon nanofibers), graphene, diamond, fullerene, carbon blacks and graphites. Explosion screening was performed in a 20 L explosion chamber (ASTM E1226-10 protocol), at a (dilute) concentration of 500 g/m3, using a 5 kJ ignition source. Time traces of overpressure were recorded. Samples exhibited overpressures of 5-7 bar, and deflagration index KSt = V1/3 (dp/pt)max ~ 10 - 80 bar-m/s, which places these materials in European Dust Explosion Class St-1 (similar to cotton and wood dust). There was minimal variation between these different materials. The explosive characteristics of these carbonaceous powders are uncorrelated with particle size (BET specific surface area). Additional tests were performed on selected materials to identify minimum explosive concentration [MEC]. These materials exhibit MEC ~ 101 -102 g/m3 (lower than the MEC for coals). The concentration scans confirm that the earlier screening was performed under fuel-rich conditions (i.e. the maximum over-pressure and deflagration index exceed the screening values); e.g. the true fullerene KSt ~ 200 bar-m/s, placing it borderline St-1/St-2. Work supported through the NIOSH Nanotechnology Research Center (NTRC)

Trend of change in retentive force for bar attachments with different materials.

PubMed

Saito, Marie; Kanazawa, Manabu; Takahashi, Hidekazu; Uo, Motohiro; Minakuchi, Shunsuke

2014-12-01

Attachment wear can decrease the retentive force of 2-implant overdentures (2-IODs). The purpose of this in vitro study was to investigate the trend of change in retentive force for 6 different bar attachments during dislodgement. Round and Dolder bars were made of platinum-added gold alloy (PGA), cobalt chromium alloy (Co-Cr), and commercially pure titanium grade IV (Ti). Clips were made of PGA. Retentive force was measured during 7200 dislodging cycles. Simple linear regression analysis was performed in order to investigate the relationship between number of cycles and retentive force (P<.05). Subsequently, wear debris was analyzed, and the surface of the attachments was observed. The retentive force of the Co-Cr round bar attachment (CoCr-R) increased from 57.5 N to 68.3 N and the Ti round bar attachment (Ti-R) from 54.8 N to 59.7 N. However, the retentive force of the PGA round bar attachment (PGA-R) decreased from 69.3 N to 64.0 N. A positive relationship was found between the number of cycles and the retentive force of both CoCr-R and Ti-R. The composition of the wear debris was almost the same as for PGA. For the Dolder bar attachment, no changes were seen in retentive force (between 7.0 N to 12.0 N). For the round bar attachment, the PGA clip and PGA bar showed wear. The retentive force of PGA-R slightly decreased. The retentive force of CoCr-R and Ti-R tended to increase. For the Dolder bar attachment, all 3 types of bar attachment showed no wear. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Prussian blue analogues for CO(2) and SO(2) capture and separation applications.

PubMed

Thallapally, Praveen K; Motkuri, Radha Kishan; Fernandez, Carlos A; McGrail, B Peter; Behrooz, Ghorishi S

2010-06-07

Adsorption isotherms of pure gases present in flue gas including CO(2), N(2), SO(2), NO, H(2)S, and water were studied using prussian blues of chemical formula M(3)[Co(CN)(6)](2).nH(2)O (M = Co, Zn) using an HPVA-100 volumetric gas analyzer and other spectroscopic methods. All the samples were characterized, and the microporous nature of the samples was studied using the BET isotherm. These materials adsorbed 8-10 wt % of CO(2) at room temperature and 1 bar of pressure with heats of adsorption ranging from 200 to 300 Btu/lb of CO(2), which is lower than monoethanolamine (750 Btu/lb of CO(2)) at the same mass loading. At high pressures (30 bar and 298 K), these materials adsorbed approximately 20-30 wt % of CO(2), which corresponds to 3 to 5 molecules of CO(2) per formula unit. Similar gas adsorption isotherms for SO(2), H(2)S, and NO were collected using a specially constructed volumetric gas analyzer. At close to 1 bar of equilibrium pressure, these materials sorb around 2.5, 2.7, and 1.2 mmol/g of SO(2), H(2)S, and NO. In particular, the uptake of SO(2) and H(2)S in Co(3)[Co(CN)(6)](2) is quite significant since it sorbs around 10 and 4.5 wt % at 0.1 bar of pressure. The stability of prussian blues before and after trace gases was studied using a powder X-ray diffraction instrument, which confirms these materials do not decompose after exposure to trace gases.

Performance et caracterisation a l'arrachement des tiges en FRP de carbone utilisees pour renforcement au cisaillement par la methode ETS

NASA Astrophysics Data System (ADS)

Ammar Khodja, L'Hady

The rehabilitation and strengthening concrete structures in shear using composite materials such as externally bonded (EB) or near surface mounted rebar (NSMR) are well established techniques. However, debonding of these strengthening materials is still present and constitute the principal cause of shear failure of beams strengthened with composite materials. A new method called ETS (Embedded Through Section) was recently developed in order to avoid premature failures due to debonding of composite materials. The objective of this study is to highlight the importance and influence of important parameters on the behavior of CFRP bars anchorages subjected to pullout forces. These parameters are: concrete strength, anchorage length of CFRP bars, hole diameter in concrete, diameter of the bar and CFRP surface type (smooth versus sanded). Understanding the influence of these parameters on the relationship between the pullout force and the slip is paramount. This allows an accurate description of the behavior of all elements that contribute to the resistance of the CFRP bars pullout. A series of 25 specimens were subjected to pullout tests. The impact of these parameters on the pullout performance of CFRP rods is summarized in terms of failure mode, ultimate tensile strength and loading force slip relationship. The results of these investigations show that using the ETS method, failure of the anchors can be avoided by providing adequate anchorage length and concrete strength. The method provides greater confinement and thus leads to a substantial improvement in the performance of anchors. As a result, designers will be able to avoid failures that are due to debonding of anchors using thereby the full capabilities of reinforced beams strengthened in shear with EB FRP. Keywords: ETS method, shear, strengthening, anchor, slip, FRP, NSM.

Numerical Study on Deflection Behaviour of Concrete Beams Reinforced with GFRP Bars

NASA Astrophysics Data System (ADS)

Mohamed, Osama A.; Khattab, Rania; Hawat, Waddah Al

2017-10-01

Fiber-Reinforced Polymer (FRP) bars are gaining popularity as sustainable alternatives to conventional reinforcing steel bars in reinforced concrete applications. The production of FRP bars has lower environmental impact compared to steel reinforcing bars. In addition, the non-corroding FRP materials can potentially decrease the cost or need for maintenance of reinforced concrete structural elements, especially in harsh environmental conditions that can impact both concrete and reinforcement. FRP bars offer additional favourable properties including high tensile strength and low unit weight. However, the mechanical properties of FRP bars can lead to large crack widths and deflections. The objective of this study is to investigate the deflection behaviour of concrete beams reinforced with Glass FRP (GFRP) bars as a longitudinal main reinforcement. Six concrete beams reinforced with GFRP bars were modelled using the finite element computer program ANSYS. The main variable considered in the study is the reinforcement ratio. The deflection equations in current North American codes including ACI 440.1R-06, ACI 440.1R-15 and CSA S806-12 are used to compute deflections, and these are compared to numerical results. It was concluded in this paper that deflections predicted by ACI 440.1R-06 equations are lower than the numerical analysis results while ACI 440.1R-15 is in agreement with numerical analysis with tendency to be conservative. The values of deflections estimated by CSA S806-12 formulas are consistent with results of numerical analysis.

Performance of Buildings in the 2009 Western Sumatra Earthquake

NASA Astrophysics Data System (ADS)

Deierlein, G.; Hart, T.; Alexander, N.; Hausler, E.; Henderson, S.; Wood, K.; Cedillos, V.; Wijanto, S.; Cabrera, C.; Rudianto, S.

2009-12-01

The M7.6 earthquake of 30 September 2009 in Western Sumatra, Indonesia caused significant damage and collapse to hundreds of buildings and the deaths of 1,117 people. In Padang City, with a population of about 900,000 people, building collapse was the primary cause of deaths and serious injuries (313 deaths and 431 serious injuries). The predominant building construction types in Padang are concrete moment frames with brick infill and masonry bearing wall systems. Concrete frames are common in multistory commercial retail buildings, offices, schools, and hotels; and masonry bearing wall systems are primarily used in low-rise (usually single story) residential and school buildings. In general, buildings that collapsed did not conform to modern seismic engineering practices that are required by the current Indonesian building code and would be expected in regions of moderate to high seismicity. While collapse of multi-story concrete buildings was more prevalent in older buildings (more than 10 years old), there were several newer buildings that collapsed. Primary deficiencies identified in collapsed or severely damaged buildings included: (a) soft or weak stories that failed in either by sidesway mechanisms or shear failures followed by loss of axial capacity of columns, (b) lack of ductile reinforcing bar detailing in concrete beams, columns, and beam-column joints, (c) poor quality concrete and mortar materials and workmanship, (d) vulnerable building configurations and designs with incomplete or deficient load paths, and (e) out-of-plane wall failures in unreinforced (or marginally reinforced) masonry. While these deficiencies may be expected in older buildings, damage and collapse to some modern (or recently rennovated buildings) indicates a lack of enforcement of building code provisions for design and construction quality assurance. Many new buildings whose structural systems were undamaged were closed due to extensive earthquake damage to brick infill walls, glass facades, ceiling systems and other architectural finishes. These demonstrated the importance of considering deformation compatibility and seismic considerations in the design and detail of architectural elements and non-structural components. Another important lesson learned from this earthquake is the critical role that buildings serve for vertical evacuation (refuge) from tsunami inundation in Padang and similar coastal cities in regions of high tsunami hazards. Severe traffic congestion immediately after the September 30 earthquake demonstrated that horizontal evacuation alone is insufficient to safely evacuate Padang City residents to high ground. Therefore, efforts must be stepped up to pre-screen, assess, and engineer buildings tha can be utilized for vertical evacuation.

Compliance with smoke-free legislation within public buildings: a cross-sectional study in Turkey.

PubMed

Navas-Acien, Ana; Çarkoğlu, Asli; Ergör, Gül; Hayran, Mutlu; Ergüder, Toker; Kaplan, Bekir; Susan, Jolie; Magid, Hoda; Pollak, Jonathan; Cohen, Joanna E

2016-02-01

To investigate public compliance with legislation to prohibit smoking within public buildings and the extent of tobacco smoking in outdoor areas in Turkey. Using a standardized observation protocol, we determined whether smoking occurred and whether ashtrays, cigarette butts and/or no-smoking signs were present in a random selection of 884 public venues in 12 cities in Turkey. We visited indoor and outdoor locations in bars/nightclubs, cafes, government buildings, hospitals, restaurants, schools, shopping malls, traditional coffee houses and universities. We used logistic regression models to determine the association between the presence of ashtrays or the absence of no-smoking signs and the presence of individuals smoking or cigarette butts. Most venues had no-smoking signs (629/884). We observed at least one person smoking in 145 venues, most frequently observed in bars/nightclubs (63/79), hospital dining areas (18/79), traditional coffee houses (27/120) and government-building dining areas (5/23). For 538 venues, we observed outdoor smoking close to public buildings. The presence of ashtrays was positively associated with indoor smoking and cigarette butts, adjusted odds ratio, aOR: 315.9; 95% confidence interval, CI: 174.9-570.8 and aOR: 165.4; 95% CI: 98.0-279.1, respectively. No-smoking signs were negatively associated with the presence of cigarette butts, aOR: 0.5; 95% CI: 0.3-0.8. Additional efforts are needed to improve the implementation of legislation prohibiting smoking in indoor public areas in Turkey, especially in areas in which we frequently observed people smoking. Possible interventions include removing all ashtrays from public places and increasing the number of no-smoking signs.

Compliance with smoke-free legislation within public buildings: a cross-sectional study in Turkey

PubMed Central

Çarkoğlu, Asli; Ergör, Gül; Hayran, Mutlu; Ergüder, Toker; Kaplan, Bekir; Susan, Jolie; Magid, Hoda; Pollak, Jonathan; Cohen, Joanna E

2016-01-01

Abstract Objective To investigate public compliance with legislation to prohibit smoking within public buildings and the extent of tobacco smoking in outdoor areas in Turkey. Methods Using a standardized observation protocol, we determined whether smoking occurred and whether ashtrays, cigarette butts and/or no-smoking signs were present in a random selection of 884 public venues in 12 cities in Turkey. We visited indoor and outdoor locations in bars/nightclubs, cafes, government buildings, hospitals, restaurants, schools, shopping malls, traditional coffee houses and universities. We used logistic regression models to determine the association between the presence of ashtrays or the absence of no-smoking signs and the presence of individuals smoking or cigarette butts. Findings Most venues had no-smoking signs (629/884). We observed at least one person smoking in 145 venues, most frequently observed in bars/nightclubs (63/79), hospital dining areas (18/79), traditional coffee houses (27/120) and government-building dining areas (5/23). For 538 venues, we observed outdoor smoking close to public buildings. The presence of ashtrays was positively associated with indoor smoking and cigarette butts, adjusted odds ratio, aOR: 315.9; 95% confidence interval, CI: 174.9–570.8 and aOR: 165.4; 95% CI: 98.0–279.1, respectively. No-smoking signs were negatively associated with the presence of cigarette butts, aOR: 0.5; 95% CI: 0.3–0.8. Conclusion Additional efforts are needed to improve the implementation of legislation prohibiting smoking in indoor public areas in Turkey, especially in areas in which we frequently observed people smoking. Possible interventions include removing all ashtrays from public places and increasing the number of no-smoking signs. PMID:26908959

UTDallas Offline Computing System for B Physics with the Babar Experiment at SLAC

NASA Astrophysics Data System (ADS)

Benninger, Tracy L.

1998-10-01

The University of Texas at Dallas High Energy Physics group is building a high performance, large storage computing system for B physics research with the BaBar experiment (``factory'') at the Stanford Linear Accelerator Center. The goal of this system is to analyze one terabyte of complex Event Store data from BaBar in one to two days. The foundation of the computing system is a Sun E6000 Enterprise multiprocessor system, with additions of a Sun StorEdge L1800 Tape Library, a Sun Workstation for processing batch jobs, staging disks and interface cards. The design considerations, current status, projects underway, and possible upgrade paths will be discussed.

Improved ceramic heat exchanger material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rauch, H.W. Sr.

Various ceramic materials in the form of small, monolithic bars were screened as candidate materials in heat exchanger structures for automotive gas turbine engines. The material finally selected consists of 60 w/o* petalite (LAS) and 40 w/o of a recrystallizable glass which converts during thermal processing to cordierite (MAS). This new material, GE-3200, was fabricated by Coors Porcelain Company into a circular honeycomb structure 53.3 cm diameter and 10.2 cm thick (21'' x 4'') and having 69.8 holes/cm/sup 2/ (450 holes/in./sup 2/) of rectangular geometry. Dimensions of each cell are about 2.5 mm x 0.5 mm (0.1'' x 0.02'') withmore » wall thicknesses about 0.20 mm (0.008''). Small bar-shaped specimens of the honeycomb were used to measure thermal, chemical, and mechanical properties and for macro- and microstructure examination. Cylindrical honeycomb specimens about 15.2 cm diameter and 10.2 in. thick (6'' x 4'') were sent to Ford Motor Company and are currently being tested in a gas turbine engine. Data obtained from testing the bar-shaped honeycomb specimens of GE-3200 and from testing bar-shaped honeycomb specimens of Corning 9455 were compared. Results indicate that GE-3200 has significantly better resistance to sulfuric acid and to sodium chloride than Corning 9455; thermal expansion of GE-3200 is higher than that of Corning 9455 (1.7 x 10/sup -6///sup 0/C vs. 0.65 x 10/sup -6///sup 0/C over the temperature range 25/sup 0/C to 1000/sup 0/C); mechanical properties of GE-3200 are higher in the tangential direction, but lower in the radial direction than Corning 9455; and during thermal cycling between R.T. 1000/sup 0/C and R.T. -1100/sup 0/C, GE-3200 tends to elongate while Corning 9455 tends to slightly contract. Overall assessment of GE-3200 properties, ease of material preparation, ready adaptability to honeycomb fabrication, and refractoriness qualify this new material as a candidate for heat exchanger application in automotive gas turbine engines.« less

Roughness, surface energy, and superficial damages of CAD/CAM materials after surface treatment.

PubMed

Strasser, Thomas; Preis, Verena; Behr, Michael; Rosentritt, Martin

2018-02-05

The aim of this study was to examine the effects of surface pre-treatment on CAD/CAM materials including ceramics, zirconia, resin-infiltrated ceramic, and resin-based composite. Specimens were made of ten CAD/CAM materials (Celtra Duo, Degudent, D; Vita Suprinity, Vita, D; E.max CAD, Ivoclar-Vivadent, FL; E.max ZirCAD, Ivoclar-Vivadent, FL; Vita Enamic, Vita, D; Cerasmart, GC, B; LAVA Ultimate, 3M, D; SHOFU Block HC, SHOFU, US; Grandio Blocs, VOCO, D; BRILLIANT Crios, Coltene, CH) and pretreated to represent clinical procedures (Hf 20 s/5%; phosphoric acid 20 s/37%; Monobond etch and prime (Ivoclar-Vivadent, FL); water-cooled diamond bur (80 μm; 4 μm); Al 2 O 3 -blasting (50 μm/1 bar, 50 μm/2 bar, 120 μm/1 bar, 120 μm/2 bar); untreated; manufacturer's instructions). SEM-analysis (Phenom, FEI, NL) of the surfaces was performed (magnifications ≤ 10,000×). Roughness values R a , R z (KJ 3D, Keyence, J), and surface energy SE (OCA15 plus, SCA20, DataPhysics, D) were determined (statistics: non-parametric Mann-Whitney U test/Kruskal-Wallis test for independent specimen, α = 0.05). Kruskal-Wallis revealed significant (p < 0.001) differences for all materials with different surface treatments. Roughness ranged from R a  = 0.05 μm (VS; D4)/R z  = 0.41 μm (VS; D4) to R a  = 1.82 μm (EMA; SB120/2)/R z  = 12.05 μm (CS; SB 120/2), SE from 22.7 mN/m (VE; M) to 52.8 mN/m (CD; M). SEM analysis showed material-dependent damages after pre-treatment. Different CAD/CAM materials require individual pre-treatment for optimized and protective surface activation. Cementation is a key factor for clinical success. Given the variety of available CAD/CAM materials, specific procedures are needed.

Single molecule magnets from magnetic building blocks

NASA Astrophysics Data System (ADS)

Kroener, W.; Paretzki, A.; Cervetti, C.; Hohloch, S.; Rauschenbach, S.; Kern, K.; Dressel, M.; Bogani, L.; M&üLler, P.

2013-03-01

We provide a basic set of magnetic building blocks that can be rationally assembled, similar to magnetic LEGO bricks, in order to create a huge variety of magnetic behavior. Using rare-earth centers and multipyridine ligands, fine-tuning of intra and intermolecular exchange interaction is demonstrated. We have investigated a series of molecules with monomeric, dimeric and trimeric lanthanide centers using SQUID susceptometry and Hall bar magnetometry. A home-made micro-Hall-probe magnetometer was used to measure magnetic hysteresis loops at mK temperatures and fields up to 17 T. All compounds show hysteresis below blocking temperatures of 3 to 4 K. The correlation of the assembly of the building blocks with the magnetic properties will be discussed.

17. VIEW OF THE FINAL STEP AT THE NO. 31 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. VIEW OF THE FINAL STEP AT THE NO. 31 MILL; THE BRASS BARS ARE WOUND ONTO SPOOLS; THE AVERAGE OUTPUT PER HOUSE SHIFT WAS 200 TO 250 BARS. MOST OF THIS MATERIAL IS USED IN THE ELECTRICAL MANUFACTURING INDUSTRY FOR FUSES, BUS FARES, ELECTRICAL RELAYS, AND OTHER SUCH PRODUCTS. - American Brass Company, Kenosha Works, Hot Roll Mill, Kenosha, Kenosha County, WI

Raise the Bar

ERIC Educational Resources Information Center

Williams, Dana

2004-01-01

Detroit's Benjamin Carson Academy (BCA) is believed to be the nation's first charter school for juvenile offenders. Opened in 1999, BCA is housed in the newly built Wayne County Juvenile Detention Facility, a state of the art, 89,300-square-foot building in downtown Detroit with half a dozen gymnasiums, two computer labs, a media center, mental…

How Do Siamese Cats Get Their Color?

ERIC Educational Resources Information Center

Todd, Amber; Kenyon, Lisa

2016-01-01

When asked about protein, students often mention meat, protein bars, and protein's role in building muscles. Many students are not aware of the most basic function of protein: linking genes and traits. Because of its importance in molecular genetics, protein function is included in the life sciences section of the "Next Generation Science…

Asphalt-derived high surface area activated porous carbons for carbon dioxide capture.

PubMed

Jalilov, Almaz S; Ruan, Gedeng; Hwang, Chih-Chau; Schipper, Desmond E; Tour, Josiah J; Li, Yilun; Fei, Huilong; Samuel, Errol L G; Tour, James M

2015-01-21

Research activity toward the development of new sorbents for carbon dioxide (CO2) capture have been increasing quickly. Despite the variety of existing materials with high surface areas and high CO2 uptake performances, the cost of the materials remains a dominant factor in slowing their industrial applications. Here we report preparation and CO2 uptake performance of microporous carbon materials synthesized from asphalt, a very inexpensive carbon source. Carbonization of asphalt with potassium hydroxide (KOH) at high temperatures (>600 °C) yields porous carbon materials (A-PC) with high surface areas of up to 2780 m(2) g(-1) and high CO2 uptake performance of 21 mmol g(-1) or 93 wt % at 30 bar and 25 °C. Furthermore, nitrogen doping and reduction with hydrogen yields active N-doped materials (A-NPC and A-rNPC) containing up to 9.3% nitrogen, making them nucleophilic porous carbons with further increase in the Brunauer-Emmett-Teller (BET) surface areas up to 2860 m(2) g(-1) for A-NPC and CO2 uptake to 26 mmol g(-1) or 114 wt % at 30 bar and 25 °C for A-rNPC. This is the highest reported CO2 uptake among the family of the activated porous carbonaceous materials. Thus, the porous carbon materials from asphalt have excellent properties for reversibly capturing CO2 at the well-head during the extraction of natural gas, a naturally occurring high pressure source of CO2. Through a pressure swing sorption process, when the asphalt-derived material is returned to 1 bar, the CO2 is released, thereby rendering a reversible capture medium that is highly efficient yet very inexpensive.

Material properties and fractography of an indirect dental resin composite.

PubMed

Quinn, Janet B; Quinn, George D

2010-06-01

Determination of material and fractographic properties of a dental indirect resin composite material. A resin composite (Paradigm, 3M-ESPE, MN) was characterized by strength, static elastic modulus, Knoop hardness, fracture toughness and edge toughness. Fractographic analyses of the broken bar surfaces was accomplished with a combination of optical and SEM techniques, and included determination of the type and size of the failure origins, and fracture mirror and branching constants. The flexure test mean strength+/-standard deviation was 145+/-17 MPa, and edge toughness, T(e), was 172+/-12N/mm. Knoop hardness was load dependent, with a plateau at 0.99+/-0.02 GPa. Mirrors in the bar specimens were measured with difficulty, resulting in a mirror constant of approximately 2.6 MPa m(1/2). Fracture in the bar specimens initiated at equiaxed material flaws that had different filler concentrations that sometimes were accompanied by partial microcracks. Using the measured flaw sizes, which ranged from 35 to 100 microm in size, and using estimates of the stress intensity shape factors, fracture toughness was estimated to be 1.1+/-0.2 MPa m(1/2). Coupling the flexure tests with fractographic examination enabled identification of the intrinsic strength limiting flaws. The same techniques could be useful in determining if clinical restorations of similar materials fail from the same causes. The existence of a strong load-dependence of the Knoop hardness of the resin composite is not generally mentioned in the literature, and is important for material comparisons and wear evaluation studies. Finally, the edge toughness test was found promising as a quantitative measure of resistance to edge chipping, an important failure mode in this class of materials. Copyright (c) 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Use of Solid Waste (Foundry Slag) Mortar and Bamboo Reinforcement in Seismic Analysis for Single Storey Masonry Building

NASA Astrophysics Data System (ADS)

Ahmad, S.; Husain, A.; Ghani, F.; Alam, M. N.

2013-11-01

The conversion of large amount of solid waste (foundry slag) into alternate source of building material will contribute not only as a solution to growing waste problem, but also it will conserve the natural resources of other building material and thereby reduce the cost of construction. The present work makes an effort to safe and economic use of recycle mortar (1:6) as a supplementary material. Conventional and recycled twelve prisms were casted with varying percentage of solid waste (foundry slag) added (0, 10, 20, 30 %) replacing cement by weight and tested under compression testing machine. As the replacement is increasing, the strength is decreasing. 10 % replacement curve is very closed to 0 % whereas 20 % is farther and 30 % is farthest. 20 % replacement was chosen for dynamic testing as its strength is within permissible limit as per IS code. A 1:4 scale single storey brick model with half size brick was fabricated on shake table in the lab for dynamic testing using pure friction isolation system (coarse sand as friction material µ = 0.34). Pure friction isolation technique can be adopted economically in developing countries where low-rise building prevails due to their low cost. The superstructure was separated from the foundation at plinth level, so as to permit sliding of superstructure during severe earthquake. The observed values of acceleration and displacement responses compare fairly with the analytical values of the analytical model. It also concluded that 20 % replacement of cement by solid waste (foundry slag) could be safely adopted without endangering the safety of the masonry structures under seismic load.To have an idea that how much energy is dissipated through this isolation, the same model with fixed base was tested and results were compared with the isolated free sliding model and it has been observed that more than 60 % energy is dissipated through this pure friction isolation technique. In case of base isolation, no visible cracks were observed up to the table force of 4.25 kN (1,300 rpm), whereas for fixed base failure started at 800 rpm.To strengthen the fixed base model, bamboo reinforcement were used for economical point of view. Another model of same dimension with same mortar ratio was fabricated on the shake table with bamboo reinforcement as plinth band and lintel band. In addition another four round bamboo bars of 3 mm diameter were placed at each of the four corners of the model. The building model was tested and found very encouraging and surprising results. The model failure started at 1,600 rpm, which means that this model is surviving the double force in comparison with the non-bamboo reinforcement.

Improved consolidation of silicon carbide

NASA Technical Reports Server (NTRS)

Freedman, M. R.; Millard, M. L.

1986-01-01

Alpha silicon carbide powder was consolidated by both dry and wet methods. Dry pressing in a double acting steel die yielded sintered test bars with an average flexural strength of 235.6 MPa with a critical flaw size of approximately 100 micro m. An aqueous slurry pressing technique produced sintered test bars with an average flexural strength of 440.8 MPa with a critical flaw size of approximately 25 micro m. Image analysis revealed a reduction in both pore area and pore size distribution in the slurry pressed sintered test bars. The improvements in the slurry pressed material properties are discussed in terms of reduced agglomeration and improved particle packing during consolidation.

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE PAGES

Song, Bo; Nelson, Kevin

2015-09-01

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Nelson, Kevin

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Experimental evaluation of low-pass shock isolation performance of elastomers using frequency-based Kolsky bar analyses

DOE PAGES

Knight, Marlene E.; Sanborn, Brett; Song, Bo; ...

2017-01-26

Elastomeric materials are used as shock isolation materials in a variety of environments to dampen vibrations and/or absorb energy from external impact to minimize energy transfer between two objects or bodies. Some applications require the shock isolation materials to behave as a low-pass mechanical filter to mitigate the shock/impact at high frequencies but transmit the energy at low frequencies with minimal attenuation. To fulfill this requirement, a shock isolation material needs to be carefully evaluated and selected with proper experimental design, procedures, and analyses. In this study, a Kolsky bar was modified with precompression (up to 15.5 kN) and confinementmore » capabilities to evaluate low-pass shock isolation performance in terms of acceleration attenuation through a variety of elastomers. Also investigated were the effects of preload and specimen geometry on the low-pass shock isolation response.« less

High-brightness line generators and fiber-coupled sources based on low-smile laser diode arrays

NASA Astrophysics Data System (ADS)

Watson, J.; Schleuning, D.; Lavikko, P.; Alander, T.; Lee, D.; Lovato, P.; Winhold, H.; Griffin, M.; Tolman, S.; Liang, P.; Hasenberg, T.; Reed, M.

2008-02-01

We describe the performance of diode laser bars mounted on conductive and water cooled platforms using low smile processes. Total smile of <1μm is readily achieved on both In and AuSn based platforms. Combined with environmentally robust lensing, these mounts form the basis of multiple, high-brightness products. Free-space-coupled devices utilizing conductively-cooled bars delivering 100W from a 200μm, 0.22NA fiber at 976nm have been developed for pumping fiber lasers, as well as for materials processing. Additionally, line generators for graphics and materials processing applications have been produced. Starting from single bars mounted on water-cooled packages that do not require de-ionized or pH-controlled water, these line generators deliver over 80W of power into a line with an aspect ratio of 600:1, and have a BPP of <2mm-mrad in the direction orthogonal to the line.

Application of Gurson–Tvergaard–Needleman Constitutive Model to the Tensile Behavior of Reinforcing Bars with Corrosion Pits

PubMed Central

Xu, Yidong; Qian, Chunxiang

2013-01-01

Based on meso-damage mechanics and finite element analysis, the aim of this paper is to describe the feasibility of the Gurson–Tvergaard–Needleman (GTN) constitutive model in describing the tensile behavior of corroded reinforcing bars. The orthogonal test results showed that different fracture pattern and the related damage evolution process can be simulated by choosing different material parameters of GTN constitutive model. Compared with failure parameters, the two constitutive parameters are significant factors affecting the tensile strength. Both the nominal yield and ultimate tensile strength decrease markedly with the increase of constitutive parameters. Combining with the latest data and trial-and-error method, the suitable material parameters of GTN constitutive model were adopted to simulate the tensile behavior of corroded reinforcing bars in concrete under carbonation environment attack. The numerical predictions can not only agree very well with experimental measurements, but also simplify the finite element modeling process. PMID:23342140

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, A.; Hayes, J.

Reported is an extensive investigation of the vandal resistance properties of common solar glazing materials. Many implements of destruction, including shotgun, splitting maul, rocks, pry bar, gasoline and logging chain, were used to determine how much abuse these glazing materials might withstand. In the hands of seasoned vandals, the glazing materials are found to be vulnerable to abuse.

23 CFR 140.908 - Materials and supplies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Reimbursement for Railroad Work § 140.908 Materials and supplies. (a) Procurement. Materials and supplies, if... job, less a consideration for loss in service life at 10 percent for rails, angle bars, tie plates and... measures for restoration of affected areas as required by the physical construction or by reason of safety...

Effect of bar cross-section geometry on stress distribution in overdenture-retaining system simulating horizontal misfit and bone loss.

PubMed

Spazzin, Aloísio Oro; Costa, Ana Rosa; Correr, Américo Bortolazzo; Consani, Rafael Leonardo Xediek; Correr-Sobrinho, Lourenço; dos Santos, Mateus Bertolini Fernandes

2013-08-09

This study evaluated the influence of cross-section geometry of the bar framework on the distribution of static stresses in an overdenture-retaining bar system simulating horizontal misfit and bone loss. Three-dimensional FE models were created including two titanium implants and three cross-section geometries (circular, ovoid or Hader) of bar framework placed in the anterior part of a severely resorbed jaw. One model with 1.4-mm vertical loss of the peri-implant tissue was also created. The models set were exported to mechanical simulation software, where horizontal displacement (10, 50 or 100 μm) was applied simulating the settling of the framework, which suffered shrinkage during the laboratory procedures. The bar material used for the bar framework was a cobalt--chromium alloy. For evaluation of bone loss effect, only the 50-μm horizontal misfit was simulated. Data were qualitatively and quantitatively evaluated using von Mises stress for the mechanical part and maximum principal stress and μ-strain for peri-implant bone tissue given by the software. Stresses were concentrated along the bar and in the join between the bar and cylinder. In the peri-implant bone tissue, the μ-strain was higher in the cervical third. Higher stress levels and μ-strain were found for the models using the Hader bar. The bone loss simulated presented considerable increase on maximum principal stresses and μ-strain in the peri-implant bone tissue. In addition, for the amplification of the horizontal misfit, the higher complexity of the bar cross-section geometry and bone loss increases the levels of static stresses in the peri-implant bone tissue. Copyright © 2013 Elsevier Ltd. All rights reserved.

Expansion-matched passively cooled heatsinks with low thermal resistance for high-power diode laser bars

NASA Astrophysics Data System (ADS)

Leers, Michael; Scholz, Christian; Boucke, Konstantin; Poprawe, Reinhart

2006-02-01

The lifetime of high-power diode lasers, which are cooled by standard copper heatsinks, is limited. The reasons are the aging of the indium solder normally employed as well as the mechanical stress caused by the mismatch between the copper heatsink (16 - 17ppm/K) and the GaAs diode laser bars (6 - 7.5 ppm/K). For micro - channel heatsinks corrosion and erosion of the micro channels limit the lifetime additionally. The different thermal behavior and the resulting stress cannot be compensated totally by the solder. Expansion matched heatsink materials like tungsten-copper or aluminum nitride reduce this stress. A further possible solution is a combination of copper and molybdenum layers, but all these materials have a high thermal resistance in common. For high-power electronic or low cost medical applications novel materials like copper/carbon compound, compound diamond or high-conductivity ceramics were developed during recent years. Based on these novel materials, passively cooled heatsinks are designed, and thermal and mechanical simulations are performed to check their properties. The expansion of the heatsink and the induced mechanical stress between laser bar and heatsink are the main tasks for the simulations. A comparison of the simulation with experimental results for different material combinations illustrates the advantages and disadvantages of the different approaches. Together with the boundary conditions the ideal applications for packaging with these materials are defined. The goal of the development of passively-cooled expansion-matched heatsinks has to be a long-term reliability of several 10.000h and a thermal resistance below 1 K/W.

Cross/bar polymer electro-optic routing switch with broadband flatting spectral response over 130 nm: Principle, design and analysis

NASA Astrophysics Data System (ADS)

Zheng, Chuan-Tao; Zheng, Li-Hua; Luo, Qian-Qian; Liang, Lei; Ma, Chun-Sheng; Zhang, Da-Ming

2013-05-01

A novel non-resonance 2×2 polymer electro-optic (EO) switch with flatting spectral response is proposed by employing two-section reversed active Mach-Zehnder interferometers (MZIs), a passive middle directional coupler (M-DC) and two passive phase generating couplers (PGCs). Two crosstalk compensations are performed by optimizing the PGCs to broaden the spectrum under bar-state and optimizing the two active MZIs to broaden the spectrum under cross-state. The bar-state and cross-state voltages are 0 and ±4 V, respectively, with the two optimized MZI EO region lengths of 4068 and 5941 μm. Sufficiently considering wavelength dispersion of material and waveguide, a wide spectrum over 130 nm (1473-1603 nm) is achieved for dropping the crosstalk below -30 dB, and within this range, an insertion loss of 1.8-12.3 dB is observed. Under the same crosstalk level, this spectrum is over 2 times of that of the traditional 2×2 MZI switch (60 nm) based on the same materials. This broadband 2×2 switch is more attractive than our previously reported broadband 1×1 switch due to cross/bar routing operations other than simple ON/OFF functions.

Analysis of Deformation and Equivalent Stress during Biomass Material Compression Molding

NASA Astrophysics Data System (ADS)

Xu, Guiying; Wei, Hetao; Zhang, Zhien; Yu, Shaohui; Wang, Congzhe; Huang, Guowen

2018-02-01

Ansys is adopted to analyze mold deformation and stress field distribution rule during the process of compressing biomass under pressure of 20Mpa. By means of unit selection, material property setting, mesh partition, contact pair establishment, load and constraint applying, and solver setting, the stress and strain of overall mold are analyzed. Deformation and equivalent Stress of compression structure, base, mold, and compression bar were analyzed. We can have conclusions: The distribution of stress forced on compressor is not completely uniform, where the stress at base is slightly decreased; the stress and strain of compression bar is the largest, and stress concentration my occur at top of compression bar, which goes against compression bar service life; the overall deformation of main mold is smaller; although there is slight difference between upper and lower part, the overall variation is not obvious, but the stress difference between upper and lower part of main mold is extremely large so that reaches to 10 times; the stress and strain in base decrease in circular shape, but there is still stress concentration in ledge, which goes against service life; contact stress does not distribute uniformly, there is increasing or decreasing trend in adjacent parts, which is very large in some parts. in constructing both.

Influence of Diamondlike Carbon Coating of Screws on Axial Tightening Force and Stress Distribution on Overdenture Bar Frameworks with Different Fit Levels and Materials.

PubMed

dos Santos, Mateus Bertolini Fernandes; Bacchi, Atais; Consani, Rafael Leonardo Xediek; Correr-Sobrinho, Lourenço

2015-01-01

The aim of this study was to evaluate the axial tightening force applied by conventional and diamondlike carbon (DLC)-coated screws and to verify, through three-dimensional finite element analysis (FEA), the stress distribution caused by different framework materials and prosthetic screws in overdenture frameworks with different misfit levels. The axial tightening force applied by the screw was evaluated by means of a titanium matrix connected to a load cell. Conventional titanium or DLC-coated screws were tightened with a digital torque wrench, and the load values were recorded. The values were applied in an FEA to a bar-clip attachment system connected to two 4.0 × 11-mm external-hexagon titanium implants placed in an anterior edentulous arch. DLC-coated and conventional screws were modeled with their respective axial forces obtained on the experimental evaluation for three bar framework materials (titanium, nickel-chromium, and cobalt-chromium) and three levels of misfit (100, 150, and 200 μm). Von Mises stresses for prosthetic components and maximum principal stress and microstrains (maximum principal strains) for bone tissue were measured. The mean force applied by the conventional screw was 25.55 N (± 1.78); the prosthetic screw coated with a DLC layer applied a mean force of 31.44 N (± 2.11), a statistically significant difference. In the FEA, the DLC screw led to higher stresses on the framework; however, the prosthetic screw suffered lower stress. No influence of screw type was seen in the bone tissue. Titanium frameworks reduced the stress transmitted to the bone tissue and the bar framework but had no influence on the screws. Higher misfit values resulted in an increased stress/strain in bone tissue and bar framework, which was not the case for retention screws.

Channel change and bed-material transport in the Lower Chetco River, Oregon

USGS Publications Warehouse

Wallick, J. Rose; Anderson, Scott W.; Cannon, Charles; O'Connor, Jim E.

2010-01-01

The lower Chetco River is a wandering gravel-bed river flanked by abundant and large gravel bars formed of coarse bed-material sediment. Since the early twentieth century, the large gravel bars have been a source of commercial aggregate for which ongoing permitting and aquatic habitat concerns have motivated this assessment of historical channel change and sediment transport rates. Analysis of historical channel change and bed-material transport rates for the lower 18 kilometers shows that the upper reaches of the study area are primarily transport zones, with bar positions fixed by valley geometry and active bars mainly providing transient storage of bed material. Downstream reaches, especially near the confluence of the North Fork Chetco River, are zones of active sedimentation and channel migration.Multiple analyses, supported by direct measurements of bedload during winter 2008–09, indicate that since 1970 the mean annual flux of bed material into the study reach has been about 40,000–100,000 cubic meters per year. Downstream tributary input of bed-material sediment, probably averaging 5–30 percent of the influx coming into the study reach from upstream, is approximately balanced by bed-material attrition by abrasion. Probably little bed material leaves the lower river under natural conditions, with most net influx historically accumulating in wider and more dynamic reaches, especially near the North Fork Chetco River confluence, 8 kilometers upstream from the Pacific Ocean.The year-to-year flux, however, varies tremendously. Some years may have less than 3,000 cubic meters of bed material entering the study area; by contrast, some high-flow years, such as 1982 and 1997, likely have more than 150,000 cubic meters entering the reach. For comparison, the estimated annual volume of gravel extracted from the lower Chetco River for commercial aggregate during 2000–2008 has ranged from 32,000 to 90,000 cubic meters and averaged about 59,000 cubic meters per year. Mined volumes probably exceeded 140,000 cubic meters per year for several years in the late 1970s.Repeat surveys and map analyses indicate a reduction in bar area and sinuosity between 1939 and 2008, chiefly in the period 1965–95. Repeat topographic and bathymetric surveys show channel incision for substantial portions of the study reach, with local areas of bed lowering by as much as 2 meters. A specific gage analysis at the upstream end of the study reach indicates that incision and narrowing followed aggradation culminating in the late 1970s. These observations are all consistent with a reduction of sediment supply relative to transport capacity since channel surveys in the late 1970s, probably owing to a combination of (1) bed sediment removal and (2) transient river adjustments to large sediment volumes brought by floods such as those in 1964 and, to a lesser extent, 1996.

Channel change and bed-material transport in the Lower Chetco River, Oregon

USGS Publications Warehouse

Wallick, J. Rose; Anderson, Scott W.; Cannon, Charles; O'Connor, Jim E.

2009-01-01

The lower Chetco River is a wandering gravel-bed river flanked by abundant and large gravel bars formed of coarse bed-material sediment. The large gravel bars have been a source of commercial aggregate since the early twentieth century for which ongoing permitting and aquatic habitat concerns have motivated this assessment of historical channel change and sediment transport rates. Analysis of historical channel change and bed-material transport rates for the lower 18 kilometers show that the upper reaches of the study area are primarily transport zones, with bar positions fixed by valley geometry and active bars mainly providing transient storage of bed material. Downstream reaches, especially near the confluence of the North Fork Chetco River, have been zones of active sedimentation and channel migration.Multiple analyses, supported by direct measurements of bedload during winter 2008–09, indicate that since 1970 the mean annual flux of bed material into the study reach has been about 40,000–100,000 cubic meters per year. Downstream tributary input of bed-material sediment, probably averaging 5–30 percent of the influx coming into the study reach from upstream, is approximately balanced by bed-material attrition by abrasion. Probably very little bed material leaves the lower river under natural conditions, with most of the net influx historically accumulating in wider and more dynamic reaches, especially near the North Fork Chetco River confluence, 8 kilometers upstream from the Pacific Ocean.The year-to-year flux, however, varies tremendously. Some years probably have less than 3,000 cubic meters of bed-material entering the study area; by contrast, some high-flow years, such as 1982 and 1997, likely have more than 150,000 cubic meters entering the reach. For comparison, the estimated annual volume of gravel extracted from the lower Chetco River for commercial aggregate during 2000–2008 has ranged from 32,000 to 90,000 cubic meters and averaged about 59,000 cubic meters per year. Mined volumes probably exceeded 140,000 cubic meters per year for several years in the late 1970s.Repeat surveys and map analyses indicate a reduction in bar area and sinuosity between 1939 and 2008, chiefly in the period 1965–95. Repeat topographic and bathymetric surveys show channel incision for substantial portions of the study reach, with local areas of bed lowering by as much as 2 meters. A specific gage analysis at the upstream end of the study reach indicates that incision and narrowing followed aggradation culminating in the late 1970s. These observations are all consistent with a reduction of sediment supply relative to transport capacity since channel surveys in the late 1970s, probably owing to a combination of (1) bed-sediment removal and (2) transient river adjustments to large sediment volumes brought by floods such as those in 1964, and to a lesser extent, 1996.

Channel Change and Bed-Material Transport in the Lower Chetco River, Oregon

NASA Astrophysics Data System (ADS)

O'Connor, J. E.; Wallick, R.; Anderson, S.; Cannon, C.

2009-12-01

The Chetco River drains 914 square kilometers of the Klamath Mountains in far southwestern Oregon. For its lowermost 18 km, it is a wandering gravel-bed river flanked by abundant and large gravel bars formed of coarse bed-material sediment. The large gravel bars have been a source of commercial aggregate since the early twentieth century for which ongoing permitting and aquatic habitat concerns have motivated an assessment of historical channel change and sediment transport rates. Analysis of historical channel change and bed-material transport rates for the lower 18 kilometers show that the upper reaches of the study area are primarily transport zones, with bar positions fixed by valley geometry and active bars mainly providing transient storage of bed material. Downstream reaches, especially near the confluence of the North Fork Chetco River, have been zones of active sedimentation and channel migration. Multiple analyses, supported by direct measurements of bedload during winter 2008-09, indicate that since 1970 the mean annual flux of bed material into the study reach has been about 40,000-100,000 cubic meters per year. Downstream tributary input of bed-material sediment, probably averaging 5-30 percent of the influx coming into the study reach from upstream, is approximately balanced by bed-material attrition by abrasion. Probably very little bed material leaves the lower river under natural conditions, with most of the net influx historically accumulating in wider and more dynamic reaches, especially near the North Fork Chetco River confluence, 8 kilometers upstream from the Pacific Ocean. The year-to-year flux, however, varies tremendously. Some years probably have less than 3,000 cubic meters of bed-material entering the study area; by contrast, some high-flow years, such as 1982 and 1997, likely have more than 150,000 cubic meters entering the reach. For comparison, the estimated annual volume of gravel extracted from the lower Chetco River for commercial aggregate during 2000-2008 has ranged from 32,000 to 90,000 cubic meters and averaged about 59,000 cubic meters per year. Mined volumes probably exceeded 140,000 cubic meters per year for several years in the late 1970s. Repeat surveys and map analyses indicate a reduction in bar area and sinuosity between 1939 and 2008, chiefly in the period 1965-95. Repeat topographic and bathymetric surveys show channel incision for substantial portions of the study reach, with local areas of bed lowering by as much as 2 meters. A specific gage analysis at the upstream end of the study reach indicates that incision and narrowing followed aggradation culminating in the late 1970s. These observations are all consistent with a reduction of sediment supply relative to transport capacity since channel surveys in the late 1970s, probably owing to a combination of (1) bed-sediment removal and (2) transient river adjustments to large sediment volumes brought by floods such as those in 1964, and to a lesser extent, 1996.

Material properties and fractography of an indirect dental resin composite

PubMed Central

Quinn, Janet B.; Quinn, George D.

2011-01-01

Objectives Determination of material and fractographic properties of a dental indirect resin composite material. Methods A resin composite (Paradigm, 3M-ESPE, MN) was characterized by strength, static elastic modulus, Knoop hardness, fracture toughness and edge toughness. Fractographic analyses of the broken bar surfaces was accomplished with a combination of optical and SEM techniques, and included determination of the type and size of the failure origins, and fracture mirror and branching constants. Results The flexure test mean strength ± standard deviation was 145 MPA ± 17 MPa, and edge toughness, Te, was 172 N/mm ±12 N/mm. Knoop hardness was load dependent, with a plateau at 0.99 GPa ± .02 GPa. Mirrors in the bar specimens were measured with difficulty, resulting in a mirror constant of approximately 2.6 MPa·m1/2. Fracture in the bar specimens initiated at equiaxed material flaws that had different filler concentrations that sometimes were accompanied by partial microcracks. Using the measured flaw sizes, which ranged from 35 µm to 100 µm in size, and estimates of the stress intensity shape factors, fracture toughness was estimated to be 1.1 MPa·m1/2 ± 0.2 MPa·m1/2. Significance Coupling the flexure tests with fractographic examination enabled identification of the intrinsic strength limiting flaws. The same techniques could be useful in determining if clinical restorations of similar materials fail from the same causes. The existence of a strong load-dependence of the Knoop hardness of the resin composite is not generally mentioned in the literature, and is important for material comparisons and wear evaluation studies. Finally, the edge toughness test was found promising as a quantitative measure of resistance to edge chipping, an important failure mode in this class of materials. PMID:20304478

Bars and spirals in tidal interactions with an ensemble of galaxy mass models

NASA Astrophysics Data System (ADS)

Pettitt, Alex R.; Wadsley, J. W.

2018-03-01

We present simulations of the gaseous and stellar material in several different galaxy mass models under the influence of different tidal fly-bys to assess the changes in their bar and spiral morphology. Five different mass models are chosen to represent the variety of rotation curves seen in nature. We find a multitude of different spiral and bar structures can be created, with their properties dependent on the strength of the interaction. We calculate pattern speeds, spiral wind-up rates, bar lengths, and angular momentum exchange to quantify the changes in disc morphology in each scenario. The wind-up rates of the tidal spirals follow the 2:1 resonance very closely for the flat and dark matter-dominated rotation curves, whereas the more baryon-dominated curves tend to wind-up faster, influenced by their inner bars. Clear spurs are seen in most of the tidal spirals, most noticeable in the flat rotation curve models. Bars formed both in isolation and interactions agree well with those seen in real galaxies, with a mixture of `fast' and `slow' rotators. We find no strong correlation between bar length or pattern speed and the interaction strength. Bar formation is, however, accelerated/induced in four out of five of our models. We close by briefly comparing the morphology of our models to real galaxies, easily finding analogues for nearly all simulations presenter here, showing passages of small companions can easily reproduce an ensemble of observed morphologies.

Effect of strain rate and temperature on mechanical properties of selected building Polish steels

NASA Astrophysics Data System (ADS)

Moćko, Wojciech; Kruszka, Leopold

2015-09-01

Currently, the computer programs of CAD type are basic tool for designing of various structures under impact loading. Application of the numerical calculations allows to substantially reduce amount of time required for the design stage of such projects. However, the proper use of computer aided designing technique requires input data for numerical software including elastic-plastic models of structural materials. This work deals with the constitutive model developed by Rusinek and Klepaczko (RK) applied for the modelling of mechanical behaviour of selected grades structural St0S, St3SX, 18GS and 34GS steels and presents here results of experimental and empirical analyses to describe dynamic elastic-plastic behaviours of tested materials at wide range of temperature. In order to calibrate the RK constitutive model, series of compression tests at wide range of strain rates, including static, quasi-static and dynamic investigations at lowered, room and elevated temperatures, were carried out using two testing stands: servo-hydraulic machine and split Hopkinson bar. The results were analysed to determine influence of temperature and strain rate on visco-plastic response of tested steels, and show good correlation with experimental data.

Autonomous exploration and mapping of unknown environments

NASA Astrophysics Data System (ADS)

Owens, Jason; Osteen, Phil; Fields, MaryAnne

2012-06-01

Autonomous exploration and mapping is a vital capability for future robotic systems expected to function in arbitrary complex environments. In this paper, we describe an end-to-end robotic solution for remotely mapping buildings. For a typical mapping system, an unmanned system is directed to enter an unknown building at a distance, sense the internal structure, and, barring additional tasks, while in situ, create a 2-D map of the building. This map provides a useful and intuitive representation of the environment for the remote operator. We have integrated a robust mapping and exploration system utilizing laser range scanners and RGB-D cameras, and we demonstrate an exploration and metacognition algorithm on a robotic platform. The algorithm allows the robot to safely navigate the building, explore the interior, report significant features to the operator, and generate a consistent map - all while maintaining localization.

Collaboratively managing sudden oak death using tangible geospatial modeling

Treesearch

Ross K. Meentemeyer; Francesco Tonini; Douglas Shoemaker; Richard C. Cobb; Brendan A. Harmon; Vaclav Petras; Anna Petrasova; Helena Mitasova

2017-01-01

Failure to build consensus amongst stakeholders has been a primary obstacle barring progress in developing and implementing strategies to manage sudden oak death (SOD). Consensus as to the goals of in situ management of SOD has rarely been reached, because stakeholders’ visions of success vary widely and often compete with each other...

On the Half Shell: An Introduction to Oysters and Their Unique Structures and Function

ERIC Educational Resources Information Center

Frederick, J. Adam; Haines, Sarah; Romano, Christina; Takacs, Jacqueline

2017-01-01

The eastern oyster, "Crassostrea virginica," is an ecologically and economically important species in Chesapeake Bay. Oysters are ecologically unique in the Chesapeake Bay because they build a structure known as a bar or reef by attaching to one another over a 45 long period of time. They have been coined the "Ecological Engineers…

Setting the Bar for School Turnaround: How Ambitious, Public Goals Can Drive School Turnaround

ERIC Educational Resources Information Center

Stanton, Larry; Segal, Alison

2013-01-01

A state education agency (SEA) can pull a powerful lever for school turnaround by setting goals publicly and releasing reports on progress toward those goals at turnaround schools to build public support for turnaround efforts. SEAs can gather information for reporting from data they already have available. This report clarifies indicators and…

76 FR 38267 - The Federal Motor Carrier Safety Administration's 2011-2016 Strategic Plan: Raising the Safety Bar

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-29

... Federal Docket Management System (FDMS) address: http://www.regulations.gov . Fax: 202-493-2251. Mail: Docket Management Facility (M-30), U.S. Department of Transportation, West Building Ground Floor, Room... transport and logistics supply chain in improving CMV safety factors. This is a holistic view of safety that...

Raising the Bar, Building Capacity: Driving Improvement in California's Continuation High Schools

ERIC Educational Resources Information Center

de Velasco, Jorge Ruiz; McLaughlin, Milbrey

2012-01-01

California's approximately 500 continuation high schools are estimated to serve more than 115,000 California high school students each year--a number that approaches almost 10 percent of all high school students and as many as one of every seven high school seniors. Continuation schools are, however, more racially and ethnically concentrated than…

Liability of Defense Contractors for Hazardous Waste Cleanup Costs

DTIC Science & Technology

1989-04-01

Comp. Gen. 85, 87 (1955); Johns - Manville Corp. v. United States, 12 Cl.Ct. 1, 22 (1987) (holding that ADA barred officials of the Federal Government from...building, converting, or repairing ships for the Government during World War II). 203. See, e.g., Johns - Manville Corp., 12 Cl.Ct. at 25. 204. Id. 205. Id

A dynamical model for the formation of gas rings and episodic starbursts near galactic centres

NASA Astrophysics Data System (ADS)

Krumholz, Mark R.; Kruijssen, J. M. Diederik

2015-10-01

We develop a simple dynamical model for the evolution of gas in the centres of barred spiral galaxies, using the Milky Way's Central Molecular Zone (CMZ, i.e. the central few hundred pc) as a case study. We show that, in the presence of a galactic bar, gas in a disc in the central regions of a galaxy will be driven inwards by angular momentum transport induced by acoustic instabilities within the bar's inner Lindblad resonance. This transport process drives turbulence within the gas that temporarily keeps it strongly gravitationally stable and prevents the onset of rapid star formation. However, at some point the rotation curve must transition from approximately flat to approximately solid body, and the resulting reduction in shear reduces the transport rates and causes gas to build up, eventually producing a gravitationally unstable region that is subject to rapid and violent star formation. For the observed rotation curve of the Milky Way, the accumulation happens ˜100 pc from the centre of the Galaxy, in good agreement with the observed location of gas clouds and young star clusters in the CMZ. The characteristic time-scale for gas accumulation and star formation is of the order of 10-20 Myr. We argue that similar phenomena should be ubiquitous in other barred spiral galaxies.

Mitochondrial phylogeny of Chinese barred species of the cyprinid genus Acrossocheilus Oshima, 1919 (Teleostei: Cypriniformes) and its taxonomic implications.

PubMed

Yuan, Le-Yang; Liu, Xiao-Xiang; Zhang, E

2015-12-21

Sequences from the mitochondrial control region of 14 putative species of Acrossocheilus (Cyprinidae) were examined to elucidate phylogenetic relationships within species of the barred group in that genus. Phylogenetic reconstructions were generated using three tree-building methods: maximum parsimony, maximum likelihood, and Bayesian inference. The resultant phylogenies were consistent with monophyly of the majority of the morphologically recognized species. However, mitochondrial DNA sequence evidence is incongruent with monophyly of A. fasciatus, as currently conceived. This species occurs only in the upper Qiantang-Jiang basin in Zhejiang and Anhui provinces, and coastal rivers in the Zhejiang Province. The species formerly recognized as A. paradoxus from Zhejiang Province is A. fasciatus. The specimens previously reported as A. fasciatus from river basins in Fujian Province are misidentified A. wuyiensis. The barred group of Acrossocheilus is shown to be polyphyletic. Acrossocheilus is restricted to the barred species here placed in "Clade II," containing A. paradoxus and relatives. Separate generic status is recommended for A. monticola and for A. longipinnis and their closest relatives, although more information on phylogenetic relationships based on multiple genes is required to develop robust phylogenetic hypotheses and diagnoses. Masticbarbus Tang, 1942 is available for A. longipinnis and three allied species (A. iridescens, A. microstomus and A. lamus).

Multilayer theory for delamination analysis of a composite curved bar subjected to end forces and end moments

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1989-01-01

A composite test specimen in the shape of a semicircular curved bar subjected to bending offers an excellent stress field for studying the open-mode delamination behavior of laminated composite materials. This is because the open-mode delamination nucleates at the midspan of the curved bar. The classical anisotropic elasticity theory was used to construct a 'multilayer' theory for the calculations of the stress and deformation fields induced in the multilayered composite semicircular curved bar subjected to end forces and end moments. The radial location and intensity of the open-mode delamination stress were calculated and were compared with the results obtained from the anisotropic continuum theory and from the finite element method. The multilayer theory gave more accurate predictions of the location and the intensity of the open-mode delamination stress than those calculated from the anisotropic continuum theory.

Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors

PubMed Central

Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

2016-01-01

The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented. PMID:26891305

Multilayer theory for delamination analysis of a composite curved bar subjected to end forces and end moments

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1989-01-01

A composite test specimen in the shape of a semicircular curved bar subjected to bending offers an excellent stress field for studying the open-mode delamination behavior of laminated composite materials. This is because the open-mode delamination nucleates at the midspan of the curved bar. The classical anisotropic elasticity theory was used to construct a multilayer theory for the calculations of the stress and deformation fields induced in the multilayered composite semicircular curved bar subjected to end forces and end moments. The radial location and intensity of the open-mode delamination stress were calculated and were compared with the results obtained from the anisotropic continuum theory and from the finite element method. The multilayer theory gave more accurate predictions of the location and the intensity of the open-mode delamination stress than those calculated from the anisotropic continuum theory.

Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors.

PubMed

Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

2016-02-16

The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented.

A mechanical property and stress corrosion evaluation of 431 stainless steel alloy

NASA Technical Reports Server (NTRS)

Montano, J. W.

1973-01-01

The mechanical properties of type 431 stainless steel in two conditions: annealed bar and hardened and tempered bar are presented. Test specimens, manufactured from approximately 1.0 inch (2.54 cm) diameter bar stock, were tested at temperatures of 80 F (+26.7 C), 0 F (-17.8 C), -100 F (-73 C), and -200 F (-129 C). The test data indicated excellent tensile strength, notched/unnotched tensile ratio, ductility, shear, and impact properties at all testing temperatures. Results of the alternate immersion stress corrosion tests on stressed and unstressed longitudinal tensile specimens 0.1250 inch (0.3175 cm) diameter and transverse C-ring specimens, machined from 1.0 inch (2.54 cm) diameter bar stock, indicated that the material is not susceptible to stress corrosion cracking when tested in a 3.5 percent NaCl solution for 180 days.

Progress in reliable single emitters and laser bars for efficient CW-operation in the near-infrared emission range

NASA Astrophysics Data System (ADS)

Zorn, Martin; Hülsewede, Ralf; Pietrzak, Agnieszka; Meusel, Jens; Sebastian, Jürgen

2015-03-01

Laser bars, laser arrays, and single emitters are highly-desired light sources e.g. for direct material processing, pump sources for solid state and fiber lasers or medical applications. These sources require high output powers with optimal efficiency together with good reliability resulting in a long lifetime of the device. Desired wavelengths range from 760 nm in esthetic skin treatment over 915 nm, 940 nm and 976 nm to 1030 nm for direct material processing and pumping applications. In this publication we present our latest developments for the different application-defined wavelengths in continuouswave operation mode. At 760nm laser bars with 30 % filling factor and 1.5 mm resonator length show optical output powers around 90-100 W using an optimized design. For longer wavelengths between 915 nm and 1030 nm laser bars with 4 mm resonator length and 50 % filling factor show reliable output powers above 200 W. The efficiency reached lies above 60% and the slow axis divergence (95% power content) is below 7°. Further developments of bars tailored for 940 nm emission wavelength reach output powers of 350 W. Reliable single emitters for effective fiber coupling having emitter widths of 90 μm and 195 μm are presented. They emit optical powers of 12 W and 24 W, respectively, at emission wavelengths of 915 nm, 940 nm and 976 nm. Moreover, reliability tests of 90 μm-single emitters at a power level of 12W currently show a life time over 3500 h.

Galaxy-scale Bars in Late-type Sloan Digital Sky Survey Galaxies Do Not Influence the Average Accretion Rates of Supermassive Black Holes

NASA Astrophysics Data System (ADS)

Goulding, A. D.; Matthaey, E.; Greene, J. E.; Hickox, R. C.; Alexander, D. M.; Forman, W. R.; Jones, C.; Lehmer, B. D.; Griffis, S.; Kanek, S.; Oulmakki, M.

2017-07-01

Galaxy-scale bars are expected to provide an effective means for driving material toward the central region in spiral galaxies, and possibly feeding supermassive black holes (BHs). Here we present a statistically complete study of the effect of bars on average BH accretion. From a well-selected sample of 50,794 spiral galaxies (with {M}* ˜ 0.2{--}30× {10}10 {M}⊙ ) extracted from the Sloan Digital Sky Survey Galaxy Zoo 2 project, we separate those sources considered to contain galaxy-scale bars from those that do not. Using archival data taken by the Chandra X-ray Observatory, we identify X-ray luminous ({L}{{X}}≳ {10}41 {erg} {{{s}}}-1) active galactic nuclei and perform an X-ray stacking analysis on the remaining X-ray undetected sources. Through X-ray stacking, we derive a time-averaged look at accretion for galaxies at fixed stellar mass and star-formation rate, finding that the average nuclear accretion rates of galaxies with bar structures are fully consistent with those lacking bars ({\\dot{M}}{acc}≈ 3× {10}-5 {M}⊙ yr-1). Hence, we robustly conclude that large-scale bars have little or no effect on the average growth of BHs in nearby (z< 0.15) galaxies over gigayear timescales.

Effect of a viscous fiber bar on postprandial glycemia in subjects with type 2 diabetes.

PubMed

Flammang, Ann M; Kendall, David M; Baumgartner, C John; Slagle, Trish D; Choe, Yong S

2006-10-01

To compare the effect of an experimental viscous fiber (VF) crispy bar on the postprandial glucose, insulin, and C-peptide response in adult subjects with type 2 diabetes to two commercially available control crispy bars. The study was a randomized, double-blinded, three period, crossover study. The study was conducted at two sites: Park Nicollet Institute, International Diabetes Center, Minneapolis, MN, and Radiant Research, Inc., Minneapolis, MN. A total of 60 adults with type 2 diabetes taking oral antihyperglycemic medication participated in the study. After an overnight fast, subjects consumed a test meal containing an equicaloric amount (300 kcal) of an experimental VF crispy bar or one of two commercially available crispy bars at each of three test visits, followed by a four hour meal tolerance test. Subjects also completed gastrointestinal (GI) response records for the 24 hours following each test visit. The VF crispy bars produced significantly lower glucose (p < 0.0001), insulin (p < 0.0001), and C-peptide (p < 0.0001) responses (as measured by positive area under the curve) in subjects with type 2 diabetes, as compared with the two commercially available bars. Intensity (p < 0.05) and frequency (p < 0.05) of flatulence were significantly higher with the VF bar as compared with the 2 commercial bars. While the VF bar produced significant subjective GI tolerance scoring values, the mean value was below 3 on a scale of 0 (no effect) to 10 (most severe effect) for all tested materials. The incorporation of VF into a crispy bar provided a means to improve blood glucose levels by reducing postprandial glucose, insulin, and C-peptide responses in subjects with type 2 diabetes. Though associated with some GI symptoms, VF may have application in improving the postprandial glycemic response in people with diabetes attempting intensive glucose control.

Hot press and roll welding of titanium-6-percent-aluminum-4-percent-vanadium bar and sheet with auto-vacuum cleaning

NASA Technical Reports Server (NTRS)

Holko, K. H.

1972-01-01

Hot press butt welds were made in 0.5 in. diameter bar, and roll lap welds were made in 0.060 in. thick sheet of Ti-6A1-4V. For hot press welds made after auto-vacuum cleaning at 1800 F for 2 hours, weld strength and ductility equaled the parent metal properties. Only 5 minutes of pressing time were needed at 1800 F and 200 psi to make the hot press welds. Roll welds were made in sheet at 1750 F with only 10 percent deformation. The welds in the bar and sheet were metallurgically indistinguishable from the parent material.

High Strain Rate Mechanical Properties of Epoxy and Epoxy-Based Particulate Composites

DTIC Science & Technology

2007-08-01

and titanium alloy (Ti- 6Al - 4V ) bar materials available. For all bar systems, the properties of the sample are determined by measuring the...polished, carbon-coated specimens provided adequate contrast between the aluminum particles, the epoxy matrix and any porosity present after curing...difference between the two measures of particle size can be explained by the higher levels of porosity observed in the Epoxy-65H2 specimen, which

Impact Response of Granular Material at Global and Meso Scales

DTIC Science & Technology

2013-02-01

compressed gas from a gas tank. The striker hits the incident bar and uni- axial stress propagates along the bar. Then, the stress propagates into the...that, at low striking velocities (e.g., below 1 km/s), the penetration of steel projectiles into aluminum targets can be described as a rigid...alloy penetrator is shot into a wax target, the Figure 1: Radiographs of a steel projectile penetrating into an aluminum target

Supporting Warfighters and U.S. Defense Sustainability with Strategic and Critical Materials

DTIC Science & Technology

2010-06-01

S155, ZFNL 9207 300M (Round bar – BAE added testing) 18 - weeks Torsion Bars M50 (2.76 ‐ 8” Diameter) 14 - weeks Bearings AMS 6491, CFR 5200, CPW 378...D1198, DMD 119‐20, EMS 52491, GE C50TF56, KBM250, MSRR 6083, PWA 725, PWA 793 and othersM50 (0.5 ‐2.75” Diameter) 14 - weeks Bearings • Latrobe Steel

Response of a channel with alternate bars to a decrease in supple of mixed-size bedload: A flume experiment

Treesearch

Thomas E. Lisle; Fujiko Iseya; Hiroshi Ikeda

1993-01-01

The response of a channel with a topography and modeled bed material size typical of gravel bed rivers to reductions in sediment supply was investigated in a laboratory flume filled and fed with a sand-gravel mixture. After a series of quasi-stationary alternate bars were formed under equilibrium sediment transport, feed rate was reduced in two steps to one third and...

Novel packaging for CW and QCW diode laser modules for operation with high power and duty cycles

NASA Astrophysics Data System (ADS)

Fassbender, Wilhelm; Lotz, Jens; Kissel, Heiko; Biesenbach, Jens

2018-02-01

Continuous wave (CW) and quasi-continuous wave (QCW) operated diode laser bars and arrays have found a wide range of industrial, medical, scientific, military and space applications with a broad variety in wavelength, pulse energy, pulse duration and beam quality. Recent applications require even higher power, duty cycles and power density. The heat loss will be dissipated by conductive cooling or liquid cooling close to the bars. We present the latest performance and reliability data of two novel high-brightness CW and QCW arrays of customized and mass-production modules, in compact and robust industry design for operation with high power and high duty cycles. All designs are based on single diode packages consisting of 10mm laser bars, soft or hard soldered between expansion matched submounts. The modular components cover a wide span of designs which differ basically in water/conduction (active/passive) cooled, single, linear (horizontal and vertical) arranged designs, as well as housed and unhoused modules. The different assembling technologies of active and passive cooled base plates affect the heat dissipation and therefore the reachable power at different QCW operating conditions, as well as the lifetime. As an example, a package consisting of 8 laser diodes, connected to a 28.8*13.5*7.0mm3 DCB (direct copper bonded) submount, passively or actively cooled is considered. This design is of particular interest for mobile applications seamless module to module building system, with an infinite number of laser bars at 1.7mm pitch. Using 940nm bars we can reach an optical output power per bar of 450W at 25°C base plate temperature with 10Hz, 1.2% duty cycle and 1.2ms pulse duration. As an additional example, micro channel coolers can be vertically stacked up to 50 diodes with a 1,15mm pitch. This design is suitable for all applications, demanding also compactness and light weight and high power density. Using near infrared bars and others, we can reach an optical output power of 250W per bar at 25°C coolant temperature at CW operation.

Bond behavior of self compacting concrete

NASA Astrophysics Data System (ADS)

Ponmalar, S.

2018-03-01

The success of an optimum design lies in the effective load transfer done by the bond forces at the steel-concrete interface. Self Compacting Concrete, is a new innovative concrete capable of filling intrinsic reinforcement and gets compacted by itself, without the need of external mechanical vibration. For this reason, it is replacing the conventional vibrated concrete in the construction industry. The present paper outlays the materials and methods adopted for attaining the self compacting concrete and describes about the bond behavior of this concrete. The bond stress-slip curve is similar in the bottom bars for both SCC and normal concrete whereas a higher bond stress and stiffness is experienced in the top and middle bars, for SCC compared to normal concrete. Also the interfacial properties revealed that the elastic modulus and micro-strength of interfacial transition zone [ITZ] were better on the both top and bottom side of horizontal steel bar in the SCC mixes than in normal vibrated concrete. The local bond strength of top bars for SCC is about 20% less than that for NC. For the bottom bars, however, the results were almost the same.

Analysis of a Stand-Alone Power System for Remote-Site Applications

DTIC Science & Technology

1986-05-01

ratio ......................... 7.5 C at rated output .................... 0.41 Bade material ......... ........... laminated wood composite Hub Material...steel lifting cables or slings and spreader bars are required (3) continental overland travel requires a flatbed truck with over-size travel permits

The significance of discharge in the replenishment of sand bar deposits along the Colorado River through the Grand Canyon

NASA Astrophysics Data System (ADS)

Wiele, S.; Hazel, J.; Schmidt, J. C.; Melis, T.

2002-12-01

Topographic sandbar surveys, recovered scour chains, analysis of aerial photos, and modeling of sand deposition demonstrate that releases from Glen Canyon Dam greater than power-plant capacity (PPC; about 900 cubic meters per second) are significantly more effective than PPC-limited releases at redistributing sand from the channel bed to higher elevations along the channel margin. A release of 1,270 m3/s (1.4 times the PPC) for 7 days in 1996 tested the effectiveness with which sandbars could be restored by the manipulation of dam releases aimed at redistributing a limited sand supply. This high flow generally resulted in substantial increases in bar size, although some sandbars close to the dam eroded. Since 1996, releases for bar building and habitat maintenance (a 2-day release in 1997 and two 4-day releases in 2000) have been limited to PPC. Field measurements indicate that the 1996 release of 1,270 m3/s significantly increased the area and volume of sand deposits at elevations greater than the stage reached during typical post-dam flows. Minor aggradation occurred during the PPC flows. In 1996, the relative extent of erosion and deposition changed longitudinally downstream as evidenced by the area of substantial deposition exceeding that of erosion at sites further downstream. The number of bars that were substantially reworked, as measured by the number of bars that significantly increased or decreased in area at the elevation range of normal dam operations, was much greater at 1,270 m3/s than at 900 m3/s. Deposition from the 1,270 m3/s release persisted at many sites on a multi-year scale whereas deposition resulting from the PPC flows only lasted a few months. Minor deposition during PPC flows in 1997, however, was greatest in upstream reaches where bar erosion during normal flows had been more extensive. These observations show that deposition is sensitive to flow magnitude and depth of inundation as well as sand supply. Flow, sand transport, and bed evolution were modeled for conditions that occurred during PPC flows and at higher discharges, such as those that occurred in 1996. Modeling results show that discharges greater than PPC form larger, higher-elevation deposits than are possible at discharges less than PPC. A key requirement for substantial deposition of new sand along the sides of this narrow, deeply incised river is the availability of depositional sites. PPC flows fail to increase stage sufficiently to create space to accommodate new deposits. The inefficiency of PPC releases at building substantial sandbars is compounded by the efficiency with which channel-bed sand is exported during PPC flows, as shown by sand-transport data collected from 1997-2000. Results to date indicate that restoration and maintenance of sand bars will likely require releases greater than PPC more frequently and of shorter duration than anticipated in the past.

Distributed Long-Gauge Optical Fiber Sensors Based Self-Sensing FRP Bar for Concrete Structure

PubMed Central

Tang, Yongsheng; Wu, Zhishen

2016-01-01

Brillouin scattering-based distributed optical fiber (OF) sensing technique presents advantages for concrete structure monitoring. However, the existence of spatial resolution greatly decreases strain measurement accuracy especially around cracks. Meanwhile, the brittle feature of OF also hinders its further application. In this paper, the distributed OF sensor was firstly proposed as long-gauge sensor to improve strain measurement accuracy. Then, a new type of self-sensing fiber reinforced polymer (FRP) bar was developed by embedding the packaged long-gauge OF sensors into FRP bar, followed by experimental studies on strain sensing, temperature sensing and basic mechanical properties. The results confirmed the superior strain sensing properties, namely satisfied accuracy, repeatability and linearity, as well as excellent mechanical performance. At the same time, the temperature sensing property was not influenced by the long-gauge package, making temperature compensation easy. Furthermore, the bonding performance between self-sensing FRP bar and concrete was investigated to study its influence on the sensing. Lastly, the sensing performance was further verified with static experiments of concrete beam reinforced with the proposed self-sensing FRP bar. Therefore, the self-sensing FRP bar has potential applications for long-term structural health monitoring (SHM) as embedded sensors as well as reinforcing materials for concrete structures. PMID:26927110

Distributed Long-Gauge Optical Fiber Sensors Based Self-Sensing FRP Bar for Concrete Structure.

PubMed

Tang, Yongsheng; Wu, Zhishen

2016-02-25

Brillouin scattering-based distributed optical fiber (OF) sensing technique presents advantages for concrete structure monitoring. However, the existence of spatial resolution greatly decreases strain measurement accuracy especially around cracks. Meanwhile, the brittle feature of OF also hinders its further application. In this paper, the distributed OF sensor was firstly proposed as long-gauge sensor to improve strain measurement accuracy. Then, a new type of self-sensing fiber reinforced polymer (FRP) bar was developed by embedding the packaged long-gauge OF sensors into FRP bar, followed by experimental studies on strain sensing, temperature sensing and basic mechanical properties. The results confirmed the superior strain sensing properties, namely satisfied accuracy, repeatability and linearity, as well as excellent mechanical performance. At the same time, the temperature sensing property was not influenced by the long-gauge package, making temperature compensation easy. Furthermore, the bonding performance between self-sensing FRP bar and concrete was investigated to study its influence on the sensing. Lastly, the sensing performance was further verified with static experiments of concrete beam reinforced with the proposed self-sensing FRP bar. Therefore, the self-sensing FRP bar has potential applications for long-term structural health monitoring (SHM) as embedded sensors as well as reinforcing materials for concrete structures.

Activity of pyramidal I and II < c + a > slip in Mg alloys as revealed by texture development

NASA Astrophysics Data System (ADS)

Zecevic, Miroslav; Beyerlein, Irene J.; Knezevic, Marko

2018-02-01

Due to the geometry of the hexagonal close-packed (HCP) lattice, there are two types of pyramidal slip modes: { 10 1 bar 1 } 〈 11 2 bar 3 bar 〉 or type I and { 1 bar 1 bar 22 } 〈 11 2 bar 3 〉 or type II in HCP crystalline materials. Here we use crystal plasticity to examine the importance of crystallographic slip by pyramidal type I and type II on texture evolution. The study is applied to an Mg-4%Li alloy. An elastic-plastic polycrystal model is employed to elucidate the reorientation tendencies of these two slip modes in rolling of a textured polycrystal. Comparisons with experimental texture measurements indicate that both pyramidal I and II type slip were active during rolling deformation, with pyramidal I being the dominant mode. A single-slip-mode analysis is used to identify the orientations that prefer pyramidal I vs. II type slip when acting alone in a crystal. The analysis applies not only to Mg-4%Li, but identifies the key texture components in HCP crystals that would help distinguish the activity of pyramidal I from pyramidal II slip in rolling deformation.

Biopower and Pedagogy: Local Spaces and Institutional Technologies

ERIC Educational Resources Information Center

Wittman, John

2006-01-01

While sitting on a bench outside the university's museum grappling with his own emotional numbness and inability to comprehend the traumatic events of 9-11, John Wittman watched a group of 4 students circling one of the main buildings on campus with an American flag on the back of the roll bar of a truck. Having thought about the flag-waving…

Acrylic Resin Molding Based Head Fixation Technique in Rodents.

PubMed

Roh, Mootaek; Lee, Kyungmin; Jang, Il-Sung; Suk, Kyoungho; Lee, Maan-Gee

2016-01-12

Head fixation is a technique of immobilizing animal's head by attaching a head-post on the skull for rigid clamping. Traditional head fixation requires surgical attachment of metallic frames on the skull. The attached frames are then clamped to a stationary platform resulting in immobilization of the head. However, metallic frames for head fixation have been technically difficult to design and implement in general laboratory environment. In this study, we provide a novel head fixation method. Using a custom-made head fixation bar, head mounter is constructed during implantation surgery. After the application of acrylic resin for affixing implants such as electrodes and cannula on the skull, additional resins applied on top of that to build a mold matching to the port of the fixation bar. The molded head mounter serves as a guide rails, investigators conveniently fixate the animal's head by inserting the head mounter into the port of the fixation bar. This method could be easily applicable if implantation surgery using dental acrylics is necessary and might be useful for laboratories that cannot easily fabricate CNC machined metal head-posts.

Anthropogenic Impacts of Recreational Use on Sandbars in Hells Canyon on the Snake River, Idaho

NASA Astrophysics Data System (ADS)

Morehead, M. D.

2014-12-01

Sandbars along large rivers are important cultural, recreational, and natural resources. In modern, historic and prehistoric times the sandbars have been used for camping, hunting, fishing and recreational activities. Sandbars are a dynamic geomorphic unit of the river system that stores and exchanges sand with the main river channel. Both natural and anthropogenic changes to river systems affect the size, shape and dynamics of sandbars. During high spring flows, the Snake River can resupply and build the sand bars. During the lower flows of the summer and fall the sand is redistributed to lower levels by natural and anthropogenic forces, where it can be remobilized by the river and exported from the bar. During the summer and fall high use season many people camp and recreate on the bars and redistribute the sand. This study utilizes change detection from repeat high resolution terrestrial LiDAR scanning surveys to study the impacts humans have on the sandbars in Hells Canyon. Nearly a decade of annual LiDAR and Bathymetric surveys were used to place these recreational impacts into the context of overall sandbar dynamics.

High Strain Rate Mechanical Properties of Epoxy and Epoxy-Based Particulate Composites (Preprint)

DTIC Science & Technology

2007-05-01

WC) and titanium alloy (Ti- 6Al - 4V ) bar materials available. For all bar systems, the properties of the sample are determined by measuring the...metallographically-polished, carbon-coated specimens provided adequate contrast between the aluminum particles, the epoxy matrix and any porosity present after...The difference between the two measures of particle size can be explained by the higher levels of porosity observed in the Epoxy-65H2 specimen, which

Optimization of Design and Manufacturing Process of Metal Foam Filled Anti-Intrusion Bars

NASA Astrophysics Data System (ADS)

Villa, Andrea; Strano, Matteo; Mussi, Valerio

2011-05-01

The role of an anti-intrusion bar for automotive use is to absorb the kinetic energy of the colliding bodies that is partially converted into internal work of the bodies involved in the crash. The aim of this paper is to investigate the performances of a new kind of anti-intrusion bars for automotive use, filled with metallic foams. The reason for using a cellular material as a filler deals with its capacity to absorb energy during plastic deformation, while being lightweight. The study is the evolution of a previous paper presented by the authors at Esaform 2010 and will present new results and findings. It is conducted by evaluating some key technical issues of the manufacturing problem and by conducting experimental and numerical analyses. The evaluation of materials and shapes of the closed sections to be filled is made in the perspective of a car manufacturer (production costs, weight reduction, space availability in a car door, etc.). Experimentally, foams are produced starting from an industrial aluminium precursor with a TiH2 blowing agent. Bars are tested in three point bending, in order to evaluate their performances in terms of force-displacement response and other specific performance parameters. In order to understand the role of interface between the inner surface of the tube and the external surface of the foam, different kinds of interface are tested.

29 CFR 1926.960 - Definitions applicable to this subpart.

Code of Federal Regulations, 2014 CFR

2014-07-01

... be so run. (k) Conductor. The term means a material, usually in the form of a wire, cable, or bus bar... rules, and those of less than 400 volts to ground may be considered as supply lines, if so run and... worked on. (oo) Unstable material. The term means earth material, other than running, that because of its...

Building the Peanut: Simulations and Observations of Peanut-shaped Structures and Ansae in Face-on Disk Galaxies

NASA Astrophysics Data System (ADS)

Saha, Kanak; Graham, Alister W.; Rodríguez-Herranz, Isabel

2018-01-01

Peanut/x-shaped features observed in a significant fraction of disk galaxies are thought to have formed from vertically buckled bars. Despite being three-dimensional structures, they are preferentially detected in near edge-on projection. Only a few galaxies are found to have displayed such structures when their disks are relatively face-on—suggesting that either they are generally weak in face-on projection or many may be hidden by the light of their galaxy’s face-on disk. Here, we report on three (collisionless) simulated galaxies displaying peanut-shaped structures when their disks are seen both face-on and edge-on—resembling a three-dimensional peanut or dumbbell. Furthermore, these structures are accompanied by ansae and an outer ring at the end of the bar—as seen in real galaxies such as IC 5240. The same set of quantitative parameters used to measure peanut structures in real galaxies has been determined for the simulated galaxies, and a broad agreement is found. In addition, the peanut length grows in tandem with the bar, and is a maximum at half the length of the bar. Beyond the cutoff of these peanut structures, toward the end of the bar, we discover a new positive/negative feature in the B 6 radial profile associated with the isophotes of the ansae/ring. Our simulated, self-gravitating, three-dimensional peanut structures display cylindrical rotation even in the near-face-on disk projection. In addition, we report on a kinematic pinch in the velocity map along the bar minor axis, matching that seen in the surface density map.

Process effects resulting from an increased BARC thickness

NASA Astrophysics Data System (ADS)

Eakin, Ronald J.; Detweiler, Shangting F.; Stagaman, Gregory J.; Tesauro, Mark R.; Spak, Mark A.; Dammel, Ralph R.

1997-07-01

Process improvements attributed to the use of bottom anti- reflective coatings (B.A.R.C.s) are well documented. As our experience with these materials improves, so does our understanding of additional optimization. Recent supplier experiments suggest an increase in the thickness of AZR BARLiTM (bottom anti-reflective layer i-line) solution to reduce photoresist swing curve ratios. Also, changes in thin film stack on common substrates can adversely affect the degree of photoresist reflective notching. It is therefore of extreme importance to determine optimum thickness(es) of a B.A.R.C. material to ensure maximum process potential. We document several process effects in the conversion of a SRAM test device (0.38 - 0.45 micrometers) from a 650 angstrom to a 2000 angstrom BARLiTM film thickness using conventional i-line photolithography. Critical dimension (CD) uniformity and depth of focus (DOF) are evaluated. Defect density between the two processes are compared before and after etch employing optical metrology and electrical test structures. Sensitivity of overlay as a function of BARLiTM film thickness is investigated as well.

Storm clouds on Saturn: Lightning-induced chemistry and associated materials consistent with Cassini/VIMS spectra

USGS Publications Warehouse

Baines, K.H.; Delitsky, M.L.; Momary, T.W.; Brown, R.H.; Buratti, B.J.; Clark, R.N.; Nicholson, P.D.

2009-01-01

Thunderstorm activity on Saturn is associated with optically detectable clouds that are atypically dark throughout the near-infrared. As observed by Cassini/VIMS, these clouds are ~20% less reflective than typical neighboring clouds throughout the spectral range from 0.8 ??m to at least 4.1 ??m. We propose that active thunderstorms originating in the 10-20 bar water-condensation region vertically transport dark materials at depth to the ~1 bar level where they can be observed. These materials in part may be produced by chemical processes associated with lightning, likely within the water clouds near the ~10 bar freezing level of water, as detected by the electrostatic discharge of lightning flashes observed by Cassini/RPWS (e.g., Fischer et al. 2008, Space Sci. Rev., 137, 271-285). We review lightning-induced pyrolytic chemistry involving a variety of Saturnian constituents, including hydrogen, methane, ammonia, hydrogen sulfide, phosphine, and water. We find that the lack of absorption in the 1-2 ??m spectral region by lightning-generated sulfuric and phosphorous condensates renders these constituents as minor players in determining the color of the dark storm clouds. Relatively small particulates of elemental carbon, formed by lightning-induced dissociation of methane and subsequently upwelled from depth - perhaps embedded within and on the surface of spectrally bright condensates such as ammonium hydrosulfide or ammonia - may be a dominant optical material within the dark thunderstorm-related clouds of Saturn. ?? 2009 Elsevier Ltd. All rights reserved.

Simulation of Texture Evolution during Uniaxial Deformation of Commercially Pure Titanium

NASA Astrophysics Data System (ADS)

Bishoyi, B.; Debta, M. K.; Yadav, S. K.; Sabat, R. K.; Sahoo, S. K.

2018-03-01

The evolution of texture in commercially pure (CP) titanium during uniaxial tension and compression through VPSC (Visco-plastic self-consistent) simulation is reported in the present study. CP-titanium was subjected to both uniaxial tension and compression upto 35% deformation. During uniaxial tension, tensile twin of \\{10\\bar{1}2\\}\\unicode{x003C;}\\bar{1}011\\unicode{x003E;} type and compressive twin of \\{11\\bar{2}2\\}\\unicode{x003C;}11\\bar{2}\\bar{3}\\unicode{x003E;} type were observed in the samples. However, only tensile twin of \\{10\\bar{1}2\\}\\unicode{x003C;}\\bar{1}011\\unicode{x003E;} type and compressive twin of type was observed in the samples during uniaxial compression. Volume fractions of the twins were increased linearly as a function of percentage deformation during uniaxial tension. Whereas, during uniaxial compression the twinning volume fraction was increased up to 20% deformation and then decreased rapidly on further increasing the percentage deformation. During uniaxial tension, the general t-type textures were observed in the samples irrespective of the percentage deformation. The initial non-basal texture was oriented to split basal texture during uniaxial compression of the sample. VPSC formulation was used for simulating the texture development in the material. Different hardening parameters were estimated through correlating the simulated stress-strain curve with the experimental stress-strain data. It was observed that, prismatic slip \\{10\\bar{1}0\\}\\unicode{x003C;}11\\bar{2}0\\unicode{x003E;} operated as the primary deformation mode during uniaxial tension whereas basal slip \\{0001\\}\\unicode{x003C;}11\\bar{2}0\\unicode{x003E;} acquired the leading role during deformation through uniaxial compression. It was also revealed that active deformation modes were fully depending on percentage deformation, loading direction, and orientation of grains.

Materials Genome in Action: Identifying the Performance Limits of Physical Hydrogen Storage

PubMed Central

2017-01-01

The Materials Genome is in action: the molecular codes for millions of materials have been sequenced, predictive models have been developed, and now the challenge of hydrogen storage is targeted. Renewably generated hydrogen is an attractive transportation fuel with zero carbon emissions, but its storage remains a significant challenge. Nanoporous adsorbents have shown promising physical adsorption of hydrogen approaching targeted capacities, but the scope of studies has remained limited. Here the Nanoporous Materials Genome, containing over 850 000 materials, is analyzed with a variety of computational tools to explore the limits of hydrogen storage. Optimal features that maximize net capacity at room temperature include pore sizes of around 6 Å and void fractions of 0.1, while at cryogenic temperatures pore sizes of 10 Å and void fractions of 0.5 are optimal. Our top candidates are found to be commercially attractive as “cryo-adsorbents”, with promising storage capacities at 77 K and 100 bar with 30% enhancement to 40 g/L, a promising alternative to liquefaction at 20 K and compression at 700 bar. PMID:28413259

Materials genome in action: Identifying the performance limits of physical hydrogen storage

DOE PAGES

Thornton, Aaron W.; Simon, Cory M.; Kim, Jihan; ...

2017-03-08

The Materials Genome is in action: the molecular codes for millions of materials have been sequenced, predictive models have been developed, and now the challenge of hydrogen storage is targeted. Renewably generated hydrogen is an attractive transportation fuel with zero carbon emissions, but its storage remains a significant challenge. Nanoporous adsorbents have shown promising physical adsorption of hydrogen approaching targeted capacities, but the scope of studies has remained limited. Here the Nanoporous Materials Genome, containing over 850 000 materials, is analyzed with a variety of computational tools to explore the limits of hydrogen storage. Optimal features that maximize net capacitymore » at room temperature include pore sizes of around 6 Å and void fractions of 0.1, while at cryogenic temperatures pore sizes of 10 Å and void fractions of 0.5 are optimal. Finally, our top candidates are found to be commercially attractive as “cryo-adsorbents”, with promising storage capacities at 77 K and 100 bar with 30% enhancement to 40 g/L, a promising alternative to liquefaction at 20 K and compression at 700 bar.« less

Biomimetic measurement of allelochemical dynamics in the rhizosphere.

PubMed

Weidenhamer, Jeffrey D

2005-02-01

Polydimethylsiloxane (PDMS) materials were used to quantify levels of the photosynthesis inhibitor sorgoleone in the undisturbed rhizosphere of sorghum plants. The materials used included stir bars coated with PDMS (stir bar sorptive extraction), technical grade optical fiber coated with a thin film of PDMS (matrix-solid phase microextraction), and PDMS tubing. PDMS tubing retained the most sorgoleone. As analyzed by high performance liquid chromatography, amounts of sorgoleone retained on the PDMS materials increased with time. Other materials tested (polyurethane foam plugs, C18 and Tenax disks, and resin capsules) proved less suitable, as they were subject to sometimes extensive penetration by fine root hairs. These results demonstrate the potential for PDMS-based materials to monitor the release of allelochemicals in the undisturbed rhizosphere of allelopathic plants. Unlike extraction procedures that recover all available compounds present in the soil, PDMS functions in a manner more analogous to plant roots in sorbing compounds from soil solution or root exudates. Information on chemical dynamics in the rhizosphere is crucial for evaluating specific hypotheses of allelopathic effects, understanding allelopathic mechanisms, and assessing the importance of allelopathic processes in plant communities.

Materials genome in action: Identifying the performance limits of physical hydrogen storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, Aaron W.; Simon, Cory M.; Kim, Jihan

The Materials Genome is in action: the molecular codes for millions of materials have been sequenced, predictive models have been developed, and now the challenge of hydrogen storage is targeted. Renewably generated hydrogen is an attractive transportation fuel with zero carbon emissions, but its storage remains a significant challenge. Nanoporous adsorbents have shown promising physical adsorption of hydrogen approaching targeted capacities, but the scope of studies has remained limited. Here the Nanoporous Materials Genome, containing over 850 000 materials, is analyzed with a variety of computational tools to explore the limits of hydrogen storage. Optimal features that maximize net capacitymore » at room temperature include pore sizes of around 6 Å and void fractions of 0.1, while at cryogenic temperatures pore sizes of 10 Å and void fractions of 0.5 are optimal. Finally, our top candidates are found to be commercially attractive as “cryo-adsorbents”, with promising storage capacities at 77 K and 100 bar with 30% enhancement to 40 g/L, a promising alternative to liquefaction at 20 K and compression at 700 bar.« less

Kinematic imprints from the bar and spiral structures in the galatic disk

NASA Astrophysics Data System (ADS)

Figueras, F.; Antoja, T.; Valenzuela, O.; Romero-Gómez, M.; Pichardo, B.; Moreno, E.

2011-12-01

At 140 years of the discovery of the moving groups, these stellar streams are emerging as powerful tools to constrain the models for the spiral arms and the Galactic bar in the Gaia era. From the kinematic-age-metallicity analysis in the solar neighbourhood it is now well established that some of these kinematic structures have a dynamical origin, different from the classical cluster disruption hypothesis. Test particle simulations allow us to definitively establish that these local structures can be created by the dynamical resonances of material spiral arms and not exclusively by the Galactic bar. First studies to evaluate the capabilities of the future Gaia data to detect and characterize moving groups at 2-6 kpc from the solar neighborhood are discussed.

Specimen size and geometry effects on fracture toughness of Al2O3 measured with short rod and short bar chevron-notch specimens

NASA Technical Reports Server (NTRS)

Shannon, J. L., Jr.; Munz, D. G.

1983-01-01

Plane strain fracture toughness measurements were made on Al2O3 using short rod and short bar chevron notch specimens previously calibrated by the authors for their dimensionless stress intensity factor coefficients. The measured toughness varied systematically with variations in specimen size, proportions, and chevron notch angle apparently due to their influence on the amount of crack extension to maximum load (the measurement point). The toughness variations are explained in terms of a suspected rising R curve for the material tested, along with a discussion of an unavoidable imprecision in the calculation of K sub Ic for materials with rising R curves when tested with chevron notch specimens.

A simple and low-cost chip bonding solution for high pressure, high temperature and biological applications.

PubMed

Serra, M; Pereiro, I; Yamada, A; Viovy, J-L; Descroix, S; Ferraro, D

2017-02-14

The sealing of microfluidic devices remains a complex and time-consuming process requiring specific equipment and protocols: a universal method is thus highly desirable. We propose here the use of a commercially available sealing tape as a robust, versatile, reversible solution, compatible with cell and molecular biology protocols, and requiring only the application of manually achievable pressures. The performance of the seal was tested with regards to the most commonly used chip materials. For most materials, the bonding resisted 5 bars at room temperature and 1 bar at 95 °C. This method should find numerous uses, ranging from fast prototyping in the laboratory to implementation in low technology environments or industrial production.

19 CFR 356.18 - Interim sanctions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... on the basis of new and material evidence or other good cause shown. The Deputy Under Secretary or a..., including the protection of proprietary information, the Deputy Under Secretary may petition an...) Barring a person from appearing before the Department; and (4) Requiring the person to return material...

Economic effect of a smoke-free law in a tobacco-growing community.

PubMed

Pyles, Mark K; Mullineaux, Donald J; Okoli, Chizimuzo T C; Hahn, Ellen J

2007-02-01

To determine whether Lexington, Kentucky's smoke-free law affected employment and business closures in restaurants and bars. On 27 April 2004, Lexington-Fayette County implemented a comprehensive ordinance prohibiting smoking in all public buildings, including bars and restaurants. Lexington is located in a major tobacco-growing state that has the highest smoking rate in the US and was the first Kentucky community to become smoke-free. A fixed-effects time series design to estimate the effect of the smoke-free law on employment and ordinary least squares to estimate the effect on business openings and closings. All restaurants and bars in Lexington-Fayette County, Kentucky and the six contiguous counties. ES-202 employment data from the Kentucky Workforce Cabinet; Business opening/closings data from the Lexington-Fayette County Health Department, Environmental Division. A positive and significant relationship was observed between the smoke-free legislation and restaurant employment, but no significant relationship was observed with bar employment. No relationship was observed between the law's implementation and employment in contiguous counties nor between the smoke-free law and business openings or closures in alcohol-serving and or non-alcohol-serving businesses. No important economic harm stemmed from the smoke-free legislation over the period studied, despite the fact that Lexington is located in a tobacco-producing state with higher-than-average smoking rates.

Economic effect of a smoke‐free law in a tobacco‐growing community

PubMed Central

Pyles, Mark K; Mullineaux, Donald J; Okoli, Chizimuzo T C; Hahn, Ellen J

2007-01-01

Objective To determine whether Lexington, Kentucky's smoke‐free law affected employment and business closures in restaurants and bars. On 27 April 2004, Lexington‐Fayette County implemented a comprehensive ordinance prohibiting smoking in all public buildings, including bars and restaurants. Lexington is located in a major tobacco‐growing state that has the highest smoking rate in the US and was the first Kentucky community to become smoke‐free. Design A fixed‐effects time series design to estimate the effect of the smoke‐free law on employment and ordinary least squares to estimate the effect on business openings and closings. Subjects and settings All restaurants and bars in Lexington‐Fayette County, Kentucky and the six contiguous counties. Main outcome measures ES‐202 employment data from the Kentucky Workforce Cabinet; Business opening/closings data from the Lexington‐Fayette County Health Department, Environmental Division. Results A positive and significant relationship was observed between the smoke‐free legislation and restaurant employment, but no significant relationship was observed with bar employment. No relationship was observed between the law's implementation and employment in contiguous counties nor between the smoke‐free law and business openings or closures in alcohol‐serving and or non‐alcohol‐serving businesses. Conclusions No important economic harm stemmed from the smoke‐free legislation over the period studied, despite the fact that Lexington is located in a tobacco‐producing state with higher‐than‐average smoking rates. PMID:17297077

Application of BIM technology in green building material management system

NASA Astrophysics Data System (ADS)

Zhineng, Tong

2018-06-01

The current green building materials management system in China's construction industry is not perfect, and there are still many shortcomings. Active construction of green building materials management system based on BIM technology, combined with the characteristics of green building materials and its relationship with BIM technology application, is urgently needed to better realize the scientific management of green building materials.

Annular Pulse Shaping Technique for Large-Diameter Kolsky Bar Experiments on Concrete

DTIC Science & Technology

2014-10-01

practiced by a number of Kolsky bar researchers on a variety of brittle materials such as glass , ceramics , and ceramic composites using relatively... glass under compression/shear loading: Experiments. J Am Ceram Soc 90:2556–2562 37. Nie X, Sanborn B, Weerasooriya T, Chen W (2012) Inertia effects in...is comprised of ASTM type I/II cement [2], Grade 120 Slag cement [5] and Class F fly ash [4]. The 1344 Exp Mech (2014) 54:1343–1354 Author’s personal

Fractured toughness of Si3N4 measured with short bar chevron-notched specimens

NASA Technical Reports Server (NTRS)

Salem, J. A.; Shannon, J. L., Jr.

1985-01-01

The short bar chevron-notched specimen is used to measure the plane strain fracture toughness of hot pressed Si3N4. Specimen proportions and chevron-notch angle are varied, thereby varying the amount of crack extension to maximum load (upon which K sub IC is based). The measured toughness (4.68 + or - 0.19 MNm to the 3/2 power) is independent of these variations, inferring that the material has a flat crack growth resistance curve.

Fracture toughness of Si3N4 measured with short bar chevron-notched specimens

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.; Shannon, John L., Jr.

1987-01-01

The short bar chevron-notched specimen is used to measure the plane strain fracture toughness of hot pressed Si3N4. Specimen proportions and chevron-notch angle are varied, thereby varying the amount of crack extension to maximum load (upon which K sub IC is based). The measured toughness (4.68 + or 0.19 MNm to the 3/2 power) is independent of these variations, inferring that the material has a flat crack growth resistance curve.

Study on the Application Mode and Legal Protection of Green Materials in Medical-Nursing Combined Building

NASA Astrophysics Data System (ADS)

Zhiyong, Xian

2017-09-01

In the context of green development, green materials are the future trend of Medical-Nursing Combined building. This paper summarizes the concept and types of green building materials. Then, on the basis of existing research, it constructs the green material system framework of Medical-Nursing Combined building, puts forward the application mode of green building materials, and studies the policy and legal protection of green material application.

Translations from Communist China’s MIN-TZU T’UAN-CHIEH (Nationality Solidarity) November and December 1959 and MIN-TZU YEN-CHIU (Nationality Research) November 1959.

DTIC Science & Technology

1960-03-31

communes came and organized col- lective living, the woman laughed and in large numbers escaped the en- cumbrance of stove and children and went to the...build your arbor, ■•-•’. = To wear- clothes ’first . spin your silkj’ • ;.,; ■■■"■■’■•’-’■■ iTo build socialism, first learn culture...now has 7$0 mou which is planted in bar- ley, oats, lucerne, millet and other grains and feeds; also beans, cabbage, celery, turnips, melons, and

Effect of substrate material selection on polychromatic integral diffraction efficiency for multilayer diffractive optics in oblique incident situation

NASA Astrophysics Data System (ADS)

Zhang, Bo; Cui, Qingfeng; Piao, Mingxu

2018-05-01

The effect of substrate material selection for multilayer diffractive optical elements (MLDOEs) on polychromatic integral diffraction efficiency (PIDE) is studied in the oblique incident situation. A mathematical model of substrate material selection is proposed to obtain the high PIDE with large incident angle. The extended expression of the microstructure heights with consideration of incident angle is deduced to calculate the PIDE difference Δ η bar(λ) for different substrate material combinations. The smaller value of Δ η bar(λ) indicates the more optimal substrate material combination in a wide incident angle range. Based on the deduced mathematical model, different MLDOEs are analyzed in visible and infrared wavebands. The results show that the three-layer DOEs can be applied in larger incident angle situation than the double-layer DOEs in visible waveband. When the two substrate materials are the same, polycarbonate (PC) is more reasonable than poly(methyl methacrylate) (PMMA) as the middle filling optical material for the three-layer DOEs. In the infrared waveband, the PIDE decreases in the LWIR are obviously smaller than that in the MWIR for the same substrate material combination, and the PIDE cannot be calculated when the incident angle larger than critical angle. The analysis results can be used to guide the hybrid optical system design with MLDOEs.

Strain Rate Behavior of HTPB-Based Magnetorheological Materials

NASA Astrophysics Data System (ADS)

Stoltz, Chad; Seminuk, Kenneth; Joshi, Vasant

2013-06-01

It is of particular interest to determine whether the mechanical properties of binder systems can be manipulated by adding ferrous or Magnetostrictive particulates. Strain rate response of two HTPB/Fe (Hydroxyl-terminated Polybutadiene/Iron) compositions under electromagnetic fields has been investigated using a Split Hopkinson Pressure bar arrangement equipped with aluminum bars. Two HTPB/Fe compositions were developed, the first without plasticizer and the second containing plasticizer. Samples were tested with and without the application of a 0.01 Tesla magnetic field coil. Strain gauge data taken from the Split Hopkinson Pressure bar has been used to determine what mechanical properties were changed by inducing a mild electromagnetic field onto each sample. The data reduction method to obtain stress-strain plots included dispersion corrections for deciphering minute changes due to compositional alterations. Data collected from the Split Hopkinson Pressure bar indicate changes in the Mechanical Stress-Strain curves and suggest that the impedance of a binder system can be altered by means of a magnetic field. We acknowledge the Defense Threat Reduction Agency for funding.

Grain size effects on stability of nonlinear vibration with nanocrystalline NiTi shape memory alloy

NASA Astrophysics Data System (ADS)

Xia, Minglu; Sun, Qingping

2017-10-01

Grain size effects on stability of thermomechanical responses for a nonlinear torsional vibration system with nanocrystalline superelastic NiTi bar are investigated in the frequency and amplitude domains. NiTi bars with average grain size from 10 nm to 100 nm are fabricated through cold-rolling and subsequent annealing. Thermomechanical responses of the NiTi bar as a softening nonlinear damping spring in the torsional vibration system are obtained by synchronised acquisition of rotational angle and temperature under external sinusoidal excitation. It is shown that nonlinearity and damping capacity of the NiTi bar decrease as average grain size of the material is reduced below 100 nm. Therefore jump phenomena of thermomechanical responses become less significant or even vanish and the vibration system becomes more stable. The work in this paper provides a solid experimental base for manipulating the undesired jump phenomena of thermomechanical responses and stabilising the mechanical vibration system through grain refinement of NiTi SMA.

The influence of plain bar on bond strength of geopolymer concrete

NASA Astrophysics Data System (ADS)

Dewi, Evrianti Syntia; Ekaputri, Januarti Jaya

2017-06-01

This paper presents some results of experimental study of bond strength of plain bar embedded in geopolymer concrete. Fly ash class F was used as a raw material activated with alkali solutions. The combination of 8 Molar of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) as alkali activators was examined in the mixture with ratio of 2.5 by weight. Nine cubical specimens with a size of 150 × 150 × 150 mm were prepared to measure bond strength and slip between reinforcement and concrete. The influential factors studied for the experimental investigation were the diameter of reinforcement bar, bond area, and concrete cover to diameter (c/d) of reinforcement. The result showed that the average bond strength decreased as the diameter of plain bar and bonded length were increased from 16 mm to 19 mm. However, the 12 mm showed the different result allegedly caused by the effect of bond area and the passive confined provided by the concrete. Based on several equations used to compare the bond strength, it is clear that deformed bar of 12 mm in diameter is potential to increase the bond strength.

Graphene oxide-based benzimidazole-crosslinked networks for high-performance supercapacitors

NASA Astrophysics Data System (ADS)

Cui, Yi; Cheng, Qian-Yi; Wu, Haiping; Wei, Zhixiang; Han, Bao-Hang

2013-08-01

The synthesis of graphene oxide (GO)-based benzimidazole-crosslinked network (GOBIN) materials is presented. These materials are prepared by the covalent crosslinking of GO sheets using a condensation reaction between the carboxylic acid moieties on the GO surface and the o-aminophenyl end groups of 3,3'-diaminobenzidine (or 1,2,4,5-benzenetetraamine tetrahydrochloride). An efficient one-pot catalyst- and template-free synthesis was performed. The obtained porous GO-based materials possess a Brunauer-Emmett-Teller specific surface area ranging from 260 to 920 m2 g-1. Electrochemical testing indicates that the GOBIN materials display a specific capacitance up to 370 F g-1 at a current density of 0.1 A g-1 and about 90% of the original capacitance is retained after 5000 cycles at a current density of 3 A g-1. Therefore, GOBIN materials can be employed as promising electrode materials for high-performance supercapacitors with outstanding cycling stability. Furthermore, owing to their significantly high specific surface area, these materials also show hydrogen uptake (up to 1.24 wt%, at 77 K and 1.0 bar) and carbon dioxide capture (up to 14.2 wt%, at 273 K and 1.0 bar) properties. As a result, these GO-based porous materials improve both the supercapacitor performance and gas sorption property, which demonstrate an excellent performance in the practical application of energy storage.The synthesis of graphene oxide (GO)-based benzimidazole-crosslinked network (GOBIN) materials is presented. These materials are prepared by the covalent crosslinking of GO sheets using a condensation reaction between the carboxylic acid moieties on the GO surface and the o-aminophenyl end groups of 3,3'-diaminobenzidine (or 1,2,4,5-benzenetetraamine tetrahydrochloride). An efficient one-pot catalyst- and template-free synthesis was performed. The obtained porous GO-based materials possess a Brunauer-Emmett-Teller specific surface area ranging from 260 to 920 m2 g-1. Electrochemical testing indicates that the GOBIN materials display a specific capacitance up to 370 F g-1 at a current density of 0.1 A g-1 and about 90% of the original capacitance is retained after 5000 cycles at a current density of 3 A g-1. Therefore, GOBIN materials can be employed as promising electrode materials for high-performance supercapacitors with outstanding cycling stability. Furthermore, owing to their significantly high specific surface area, these materials also show hydrogen uptake (up to 1.24 wt%, at 77 K and 1.0 bar) and carbon dioxide capture (up to 14.2 wt%, at 273 K and 1.0 bar) properties. As a result, these GO-based porous materials improve both the supercapacitor performance and gas sorption property, which demonstrate an excellent performance in the practical application of energy storage. Electronic supplementary information (ESI) available: Detailed methods of preparation of GOBINPPA, SEM images, IR spectra, TGA, nitrogen adsorption-desorption isotherms, pore size distribution, gravimetric hydrogen adsorption, carbon dioxide adsorption isotherms, and virial analysis of the adsorption data for GOBIN materials. See DOI: 10.1039/c3nr01480k

Biomechanical and Cost Comparisons of Near-Far and Pin-Bar Constructs.

PubMed

Whitney Kluk, Augusta; Zhang, Tina; Russell, Joseph P; Kim, Hyunchul; Hsieh, Adam H; O'Toole, Robert V

2017-03-01

Orthopedic dogma states that external fixator stiffness is improved by placing 1 pin close to the fracture and 1 as distant as possible ("near-far"). This fixator construct is thought to be less expensive than placing pins a shorter distance apart and using "pin-bar" clamps that attach pins to outriggers. The authors therefore hypothesized that the near-far construct is stiffer and less expensive. They compared mechanical stiffness and costs of near-far and pin-bar constructs commonly used for temporary external fixation of femoral shaft fractures. Their testing model simulated femoral shaft fractures in damage control situations. Fourth-generation synthetic femora (n=18) were used. The near-far construct had 2 pins that were 106 mm apart, placed 25 mm from the gap on each side of the fracture. The pin-bar construct pins were 55 mm apart, placed 40 mm from the gap. Mechanical testing was performed on a material test system machine. Stiffness was determined in the linear portion of the load-displacement curve for both constructs in 4 modes: axial compression, torsional loading, frontal plane 3-point bending, and sagittal plane 3-point bending. Costs were determined from a 2012 price guide. Compared with the near-far construct, the pin-bar construct had stiffness increased by 58% in axial compression (P<.05) and by 52% in torsional loading (P<.05). The pin-bar construct increased cost by 11%. In contrast to the authors' hypothesis and existing orthopedic dogma, the near-far construct was less stiff than the pin-bar construct and was similarly priced. Use of the pin-bar construct is mechanically and economically reasonable. [Orthopedics. 2017; 40(2):e238-e241.]. Copyright 2016, SLACK Incorporated.

Mechanical splicing of superelastic Cu–Al–Mn alloy bars with headed ends

NASA Astrophysics Data System (ADS)

Kise, S.; Mohebbi, A.; Saiidi, M. S.; Omori, T.; Kainuma, R.; Shrestha, K. C.; Araki, Y.

2018-06-01

This paper examines the feasibility of mechanical splicing using a steel coupler to connect headed ends of superelastic Cu–Al–Mn alloy (Camalloy) bars and steel reinforcing bars to be used in concrete structures. Although threading of Camalloy is as easy as that of steel, mechanical splicing using threaded ends requires machining of Camalloy bars into dog-bone shape to avoid brittle fracture at the threaded ends. The machining process requires significant time and cost and wastes substantial amount of the material. This paper attempts to resolve this issue by applying mechanical splicing using steel couplers to connect headed ends of Camalloy and steel reinforcing bars. To study its feasibility, we prepare 3 specimens wherein both ends of each Camalloy bar (13 mm diameter and 300 mm length) are connected to steel reinforcing bars. The specimens are tested under monotonic, single-cycle, and full-cycle tension loading conditions. From these tests, we observed (1) excellent superelasticity with recoverable strain of around 6% and (2) large ductility with fracture strain of over 19%. It should be emphasized here that, in all the specimens, ductile fracture occurred at the locations apart from the headed ends. This is in sharp contrast with brittle fracture of headed superelastic Ni–Ti SMA bars, most of which took place around the headed ends. From the results of the microstructural analysis, we identified the following reasons for avoiding brittle fracture at the headed ends: (1) Precipitation hardening increases the strength around the boundary between the straight and headed (tapered) portions, where stress concentration takes place. (2) The strength of the straight portion does not increase significantly up to the ductile fracture if its grain orientation is close to 〈0 0 1〉.

Evaluation of stress distribution of implant-retained mandibular overdenture with different vertical restorative spaces: A finite element analysis

PubMed Central

Ebadian, Behnaz; Farzin, Mahmoud; Talebi, Saeid; Khodaeian, Niloufar

2012-01-01

Background: Available restorative space and bar height is an important factor in stress distribution of implant-supported overdentures. The purpose of this study was to evaluate the effect of different vertical restorative spaces and different bar heights on the stress distribution around implants by 3D finite element analysis. Materials and Methods: 3D finite element models were developed from mandibular overdentures with two implants in the interforaminal region. In these models, four different bar heights from gingival crest (0.5, 1, 1.5, 2 mm) with 15 mm occlusal plane height and three different occlusal plane heights from gingival crest (9, 12, 15 mm) with 2 mm bar height were analyzed. A vertical unilateral and a bilateral load of 150 N were applied to the central occlusal fossa of the first molar and the stress of bone around implant was analyzed by finite element analysis. Results: By increasing vertical restorative space, the maximum stress values around implants were found to be decreased in unilateral loading models but slightly increased in bilateral loading cases. By increasing bar height from gingival crest, the maximum stress values around implants were found to be increased in unilateral loading models but slightly decreased in bilateral loading cases. In unilateral loading models, maximum stress was found in a model with 9 mm occlusal plane height and 1.5 mm bar height (6.254 MPa), but in bilateral loading cases, maximum stress was found in a model with 15 mm occlusal plane height and 0.5 mm bar height (3.482 MPa). Conclusion: The reduction of bar height and increase in the thickness of acrylic resin base in implant-supported overdentures are biomechanically favorable and may result in less stress in periimplant bone. PMID:23559952

Three-dimensional accuracy of different correction methods for cast implant bars

PubMed Central

Kwon, Ji-Yung; Kim, Chang-Whe; Lim, Young-Jun; Kwon, Ho-Beom

2014-01-01

PURPOSE The aim of the present study was to evaluate the accuracy of three techniques for correction of cast implant bars. MATERIALS AND METHODS Thirty cast implant bars were fabricated on a metal master model. All cast implant bars were sectioned at 5 mm from the left gold cylinder using a disk of 0.3 mm thickness, and then each group of ten specimens was corrected by gas-air torch soldering, laser welding, and additional casting technique. Three dimensional evaluation including horizontal, vertical, and twisting measurements was based on measurement and comparison of (1) gap distances of the right abutment replica-gold cylinder interface at buccal, distal, lingual side, (2) changes of bar length, and (3) axis angle changes of the right gold cylinders at the step of the post-correction measurements on the three groups with a contact and non-contact coordinate measuring machine. One-way analysis of variance (ANOVA) and paired t-test were performed at the significance level of 5%. RESULTS Gap distances of the cast implant bars after correction procedure showed no statistically significant difference among groups. Changes in bar length between pre-casting and post-correction measurement were statistically significance among groups. Axis angle changes of the right gold cylinders were not statistically significance among groups. CONCLUSION There was no statistical significance among three techniques in horizontal, vertical and axial errors. But, gas-air torch soldering technique showed the most consistent and accurate trend in the correction of implant bar error. However, Laser welding technique, showed a large mean and standard deviation in vertical and twisting measurement and might be technique-sensitive method. PMID:24605205

Greedy bases in rank 2 quantum cluster algebras

PubMed Central

Lee, Kyungyong; Li, Li; Rupel, Dylan; Zelevinsky, Andrei

2014-01-01

We identify a quantum lift of the greedy basis for rank 2 coefficient-free cluster algebras. Our main result is that our construction does not depend on the choice of initial cluster, that it builds all cluster monomials, and that it produces bar-invariant elements. We also present several conjectures related to this quantum greedy basis and the triangular basis of Berenstein and Zelevinsky. PMID:24982182

Building the Missing Link between the Common Core and Improved Learning

ERIC Educational Resources Information Center

Rodde, Amy Coe; McHugh, Lija

2013-01-01

The Common Core State Standards, adopted by 45 states and the District of Columbia, raise the bar for what students need to learn at each stage of their K-12 education. The goal is to better prepare students for college and careers. The most important thing that education leaders can do to help the Common Core succeed is to support teachers in…

The Use Potential of Traditional Building Materials for the Realization of Structures by Modern Methods of Construction

NASA Astrophysics Data System (ADS)

Spišáková, Marcela; Mačková, Daniela

2015-11-01

The sustainable building has taken off in recent years with many investors looking for new and different methods of construction. The traditional building materials can be made out of natural materials, while others can help to lower energy costs of the occupant once built. Regardless of what the goal of the investor is, traditional building materials and their use is on the rise. The submitted paper provides an overview of natural building materials and possible modern building systems using these construction materials. Based on the questionnaire survey is defined the use potential of traditional building materials for the realization of the construction by methods of modern constructions and then are determined the drivers and barriers of traditional materials through using modern methods of construction. Considering the analysis of the achieved results, we can identify the gaps in the construction market in Slovakia and also to assess the perception of potential investors in the field of traditional building materials use, which is the purpose of submitted paper.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti

Targeted synthesis of microporous adsorbents for CO{sub 2} capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO{sub 2} storage capacities: SB-TRZ-CRZ displayed the CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO{sub 2} boosts the selectivity for CO{sub 2}/N{sub 2}.more » SB-TRZ-CRZ has this CO{sub 2}/N{sub 2} selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues. - Graphical abstract: We report two novel N-rich microporous polymeric materials by doping of triazine containing tripodal dopant in the organic framework. These materials showed excellent CO{sub 2} storage capacities as high as 25.5 wt% under 1 bar pressure with exceptional CO{sub 2}/N{sub 2} selectivity of 377. - Highlights: • Triazine containing trimodal moiety incorporated in polycarbazolic and poly triphenylamine networks. • N-rich crosslinked polymers with high BET surface area and 1.5–1.7 nm size large micropores. • CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K. • These crosslinked porous polymers showed exceptional CO{sub 2}/N{sub 2} selectivity.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bateman, V.I.; Bell, R.G. III; Brown, F.A.

Sandia National Laboratories (SNL) designs mechanical systems with electronics that must survive high shock environments. These mechanical systems include penetrators that must survive soil, rock, and ice penetration, nuclear transportation casks that must survive transportation environments, and laydown weapons that must survive delivery impact of 125-fps. These mechanical systems contain electronics that may operate during and after the high shock environment and that must be protected from the high shock environments. A study has been started to improve the packaging techniques for the advanced electronics utilized in these mechanical systems because current packaging techniques are inadequate for these more sensitivemore » electronics. In many cases, it has been found that the packaging techniques currently used not only do not mitigate the shock environment but actually amplify the shock environment. An ambitious goal for this packaging study is to avoid amplification and possibly attenuate the shock environment before it reaches the electronics contained in the various mechanical system. As part of the investigation of packaging techniques, a two part study of shock mitigating materials is being conducted. This paper reports the first part of the shock mitigating materials study. A study to compare three thicknesses (0.125, 0.250, and 0.500 in.) of seventeen, unconfined materials for their shock mitigating characteristics has been completed with a split Hopkinson bar configuration. The nominal input as measured by strain gages on the incident Hopkinson bar is 50 fps {at} 100 {micro}s for these tests. It is hypothesized that a shock mitigating material has four purposes: to lengthen the shock pulse, to attenuate the shock pulse, to mitigate high frequency content in the shock pulse, and to absorb energy. Both time domain and frequency domain analyses of the split Hopkinson bar data have been performed to compare the materials` achievement of these purposes.« less

Geomorphic field experiment to quantify grain size and biotic influence on riverbed sedimentation dynamics in a dry-season reservoir, Russian River, CA

NASA Astrophysics Data System (ADS)

Florsheim, J. L.; Ulrich, C.; Hubbard, S. S.; Borglin, S. E.; Rosenberry, D. O.

2013-12-01

An important problem in geomorphology is to differentiate between abiotic and biotic fine sediment deposition on coarse gravel river beds because of the potential for fine sediment to infiltrate and clog the pore space between gravel clasts. Infiltration of fines into gravel substrate is significant because it may reduce permeability; therefore, differentiation of abiotic vs. biotic sediment helps in understanding the causes of such changes. We conducted a geomorphic field experiment during May to November 2012 in the Russian River near Wohler, CA, to quantify biotic influence on riverbed sedimentation in a small temporary reservoir. The reservoir is formed upstream of a small dam inflated during the dry season to enhance water supply pumping from the aquifer below the channel; however, some flow is maintained in the reservoir to facilitate fish outmigration. In the Russian River field area, sediment transport dynamics during storm flows prior to dam inflation created an alternate bar-riffle complex with a coarser gravel surface layer over the relatively finer gravel subsurface. The objective of our work was to link grain size distribution and topographic variation to biotic and abiotic sediment deposition dynamics in this field setting where the summertime dam annually increases flow depth and inundates the bar surfaces. The field experiment investigated fine sediment deposition over the coarser surface sediment on two impounded bars upstream of the reservoir during an approximately five month period when the temporary dam was inflated. The approach included high resolution field surveys of topography, grain size sampling and sediment traps on channel bars, and laboratory analyses of grain size distributions and loss on ignition (LOI) to determine biotic content. Sediment traps were installed at six sites on bars to measure sediment deposited during the period of impoundment. Preliminary results show that fine sediment deposition occurred at all of the sample sites, and is spatially variable--likely influenced by topographic differences that moderate flow over the bars. Traps initially filled with coarse gravel from the bar's surface trapped more fine sediment than traps initially filled with material from the bar's subsurface sediment, suggesting that a gravel bar's armor layer may enhance the source of material available to infiltrate into the channel substrate. LOI analysis indicates that both surface and subsurface samples have organic content ranging between 2 and 4%, following winter storm flows prior to impoundment. In contrast, samples collected after the 5-month impoundment have higher organic content ranging between 5 and 11%. This work aids in differentiating between abiotic and biotic fine sediment deposition in order to understand their relative potential for clogging gravel substrate.

Monochromatic radio frequency accelerating cavity

DOEpatents

Giordano, S.

1984-02-09

A radio frequency resonant cavity having a fundamental resonant frequency and characterized by being free of spurious modes. A plurality of spaced electrically conductive bars are arranged in a generally cylindrical array within the cavity to define a chamber between the bars and an outer solid cylindrically shaped wall of the cavity. A first and second plurality of mode perturbing rods are mounted in two groups at determined random locations to extend radially and axially into the cavity thereby to perturb spurious modes and cause their fields to extend through passageways between the bars and into the chamber. At least one body of lossy material is disposed within the chamber to damp all spurious modes that do extend into the chamber thereby enabling the cavity to operate free of undesired spurious modes.

Monochromatic radio frequency accelerating cavity

DOEpatents

Giordano, Salvatore

1985-01-01

A radio frequency resonant cavity having a fundamental resonant frequency and characterized by being free of spurious modes. A plurality of spaced electrically conductive bars are arranged in a generally cylindrical array within the cavity to define a chamber between the bars and an outer solid cylindrically shaped wall of the cavity. A first and second plurality of mode perturbing rods are mounted in two groups at determined random locations to extend radially and axially into the cavity thereby to perturb spurious modes and cause their fields to extend through passageways between the bars and into the chamber. At least one body of lossy material is disposed within the chamber to damp all spurious modes that do extend into the chamber thereby enabling the cavity to operate free of undesired spurious modes.

OR14-V-Uncertainty-PD2La Uncertainty Quantification for Nuclear Safeguards and Nondestructive Assay Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nicholson, Andrew D.; Croft, Stephen; McElroy, Robert Dennis

2017-08-01

The various methods of nondestructive assay (NDA) of special nuclear material (SNM) have applications in nuclear nonproliferation, including detection and identification of illicit SNM at border crossings and quantifying SNM at nuclear facilities for safeguards. No assay method is complete without “error bars,” which provide one way of expressing confidence in the assay result. Consequently, NDA specialists typically provide error bars and also partition total uncertainty into “random” and “systematic” components so that, for example, an error bar can be developed for the total mass estimate in multiple items. Uncertainty Quantification (UQ) for NDA has always been important, but itmore » is recognized that greater rigor is needed and achievable using modern statistical methods.« less

Rotor for a line start permanent magnet machine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melfi, Mike; Schiferl, Rich; Umans, Stephen

A rotor comprises laminations with a plurality of rotor bar slots with an asymmetric arrangement about the rotor. The laminations also have magnet slots equiangularly spaced about the rotor. The magnet slots extend near to the rotor outer diameter and have permanent magnets disposed in the magnet slots creating magnetic poles. The magnet slots may be formed longer than the permanent magnets disposed in the magnets slots and define one or more magnet slot apertures. The permanent magnets define a number of poles and a pole pitch. The rotor bar slots are spaced from adjacent magnet slots by a distancemore » that is at least 4% of the pole pitch. Conductive material is disposed in the rotor bar slots, and in some embodiments, may be disposed in the magnet slot apertures.« less

High Pressure Gas Permeation and Liquid Diffusion Studies of Coflon and Tefzel Thermoplastics. Revision

NASA Technical Reports Server (NTRS)

Morgan, G. J.; Campion, R. P.

1997-01-01

The life of fluid-carrying flexible or umbilical pipes during service at elevated temperatures and pressures depends inter alia on their resistance to attack by the fluids present and the rate at which these fluids are absorbed by the pipe lining materials. The consequences of fluid ingress into the thermoplastic lining could mean a) a reduction in its mechanical strength, to increase chances of crack formation and growth and thus a loss of integrity, b) the occurrence of permeation right through the lining material, with pressure build- up in the outer pipe wall construction (of flexible pipes) or chemical attack (from a hostile permeant) on outer layers of reinforcements. Therefore it is important within this project to have relevant permeation data for Coflon and Tefzel thermoplastics: the former is plasticised, the latter is not. A previous report (CAPP/M.2) described experimental equipment and techniques used by MERL when measuring high pressure (up to 5000 psi) gas permeation and liquid diffusion through thermoplastic samples cut from extruded bar or pipe, and provided the basic theory involved. Norsk Hydro are also performing gas permeation tests on pipe sections, at up to 100 bars (1450 psi) pressure or so, and reporting separately. Some comparisons between data from Norsk Hydro and MERL have been made herein. The tests should be considered as complementary, as the Norsk Hydro test has the obvious benefit of using complete pipe sections, whilst MERL can test at much higher pressures, up to 1000 bar if necessary. The sophisticated analytical measuring equipment of Norsk Hydro can distinguish the individual components of mixed gases and hence the various permeation-linked coefficients whereas MERL, in using pressure increase at constant volume to determine permeation rate, is limited to obtaining single gas data, or apparent (or representative) coefficients for a mixed gas as a whole. Except for the initial fluid diffusion data for Tefzel described in CAPP/M.2, the present report covers all aspects of fluid permeation and diffusion for Coflon and Tefzel, including all the pen-neation data accumulated in the project to date. Test gases have mainly been methane (CH4) and carbon dioxide (CO2). More high pressure (HP) gas permeation tests have been performed since the last issue of this report, most being concerned with changes in permeation characteristics brought about by ageing in various relevant fluids. This revision supersedes previous issues.

Pressure-induced stable BeN4 as a high-energy density material

NASA Astrophysics Data System (ADS)

Zhang, Shoutao; Zhao, Ziyuan; Liu, Lulu; Yang, Guochun

2017-10-01

Polynitrogens are the ideal rocket fuels or propellants. Due to strong triple N≡N bond in N2, the direct polymerization of nitrogen is rather difficult (i.e. extreme high temperature and high pressure). However, the use of nitrides as precursors or the reaction of N2 with other elements has been proved to be an effective way to obtain polynitrogens. Here, with assistance of the advanced first-principles swarm-intelligence structure searches, we found that P 1 bar -BeN4, containing infinite zigzag-like polymeric nitrogen chains, can be synthesized by compressing the mixture of Be3N2 and N2 at 25.4 GPa, which is greatly lower than 110 GPa for synthesizing cubic gauche nitrogen and other polynitrogen compounds (e.g. bulk CNO at 52 GPa and SN4 at 49 GPa). Its structural stability can be attributed to the coexistence of ionic Be-N and covalent N-N bonds. Intriguingly, this phase has high kinetic stability and remains metastable at ambient pressure. The exceptional properties, including high energy density (3.60 kJ g-1), high nitrogen content (86.1%), high dynamical stability, and low polymerization pressure, make P 1 bar -structured BeN4 a promising high energy material. Infinite nitrogen chains in P 1 bar -BeN4 transform to N10 rings network in P21/c phase at 115.1 GPa. P 1 bar -BeN4 is metallic, while P21/c-BeN4 is an insulator.

Surface fatigue life of M50NiL and AISI 9310 spur gears and R C bars

NASA Technical Reports Server (NTRS)

Townsend, Dennis P.; Bamberger, Eric N.

1991-01-01

Spur gear endurance tests and rolling element surface fatigue tests were conducted to study vacuum induction melted, vacuum arc remelted (VIM-VAR) M50NiL steel for use as a gear steel in advanced aircraft applications, to determine its endurance characteristics, and to compare the results with those for standard VAR and VIM-VAR AISI 9310 gear material. Tests were conducted with spur gears and rolling contact bars manufactured from VIM-VAR M50NiL and VAR and VIM-VAR AISI 9310. The gear pitch diameter was 8.9 cm. Gear test conditions were an inlet oil temperature of 320 K, and outlet oil temperature of 350 K, a maximum Hertz stress of 1.71 GPa, and a speed of 10000 rpm. Bench rolling element fatigue tests were conducted at ambient temperatures with a bar speed of 12,500 rpm and a maximum Hertz stress of 4.83 GPa. The VIM-VAR M50NiL gears had a surface fatigue life that was 4.5 and 11.5 times that for VIM-VAR and VAR AISI 9310 gears, respectively. The surface fatigue life of the VIM-VAR M50NiL rolling contact bars was 13.2 and 21.6 times that for the VIM-VAR and VAR AISI 9310, respectively. The VIM-VAR M50NiL material was shown to have good resistance to fracture through a fatigue spall and superior fatigue life to both other gears.

Finite element normal mode analysis of resistance welding jointed of dissimilar plate hat structure

NASA Astrophysics Data System (ADS)

Nazri, N. A.; Sani, M. S. M.

2017-10-01

Structural joints offer connection between structural element (beam, plate, solid etc.) in order to build a whole assembled structure. The complex behaviour of connecting elements plays a valuable role in characteristics of dynamic such as natural frequencies and mode shapes. In automotive structures, the trustworthiness arrangement of the structure extremely depends on joints. In this paper, top hat structure is modelled and designed with spot welding joint using dissimilar materials which is mild steel 1010 and stainless steel 304, using finite element software. Different types of connector elements such as rigid body element (RBE2), welding joint element (CWELD), and bar element (CBAR) are applied to represent real connection between two dissimilar plates. Normal mode analysis is simulated with different types of joining element in order to determine modal properties. Natural frequencies using RBE2, CBAR and CWELD are compared to equivalent rigid body method. Connection that gives the lowest percentage error among these three will be selected as the most reliable joining for resistance spot weld. From the analysis, it is shown that CWELD is better compared to others in term of weld joining among dissimilar plate materials. It is expected that joint modelling of finite element plays significant role in structural dynamics.

Measurement of natural radioactivity in building materials used in Urumqi, China.

PubMed

Ding, Xiang; Lu, Xinwei; Zhao, Caifeng; Yang, Guang; Li, Nan

2013-07-01

Building materials contain natural radionuclides (226)Ra, (232)Th and (40)K, which cause direct radiation exposure of the public. The concentrations of (226)Ra, (232)Th and (40)K in commonly used building materials of Urumqi, China have been analysed using gamma-ray spectrometry. The concentrations of (226)Ra, (40)K and (232)Th in the studied building materials range from 19.8 to 87.4, from 273.3 to 981.2 and from 11.6 to 47.7 Bq kg(-1), respectively. The radium equivalent activity (Raeq), gamma index (Iγ) and alpha index (Iα) were calculated to assess the radiation hazards to people living in dwellings made of the materials studied. The calculated Raeq values of all the building materials are lower than the limit of 370 Bq kg(-1) for building materials. The values of Iγ and Iα of all the building materials are less than unity. The study shows that these materials may be safely used as construction materials and do not pose significant radiation hazards.

Diagnostic tool for structural health monitoring: effect of material nonlinearity and vibro-impact process

NASA Astrophysics Data System (ADS)

Hiwarkar, V. R.; Babitsky, V. I.; Silberschmidt, V. V.

2013-07-01

Numerous techniques are available for monitoring structural health. Most of these techniques are expensive and time-consuming. In this paper, vibration-based techniques are explored together with their use as diagnostic tools for structural health monitoring. Finite-element simulations are used to study the effect of material nonlinearity on dynamics of a cracked bar. Additionally, several experiments are performed to study the effect of vibro-impact behavior of crack on its dynamics. It was observed that a change in the natural frequency of the cracked bar due to crack-tip plasticity and vibro-impact behavior linked to interaction of crack faces, obtained from experiments, led to generation of higher harmonics; this can be used as a diagnostic tool for structural health monitoring.

Comparative study of hydrogen storage on metal doped mesoporous materials

NASA Astrophysics Data System (ADS)

Carraro, P. M.; Sapag, K.; Oliva, M. I.; Eimer, G. A.

2018-06-01

The hydrogen adsorption capacity of mesoporous materials MCM-41 modified with Co, Fe, Ti, Mg and Ni at 77 K and 10 bar was investigated. Various techniques including XRD, N2 adsorption and DRUV-vis were employed for the materials characterization. The results showed that a low nickel loading on MCM-41 support promoted the presence of hydrogen-favorable sites, increasing the hydrogen storage capacity.

Effect of phase change material on the heat transfer rate of different building materials

NASA Astrophysics Data System (ADS)

Hasan, Mushfiq; Alam, Shahnur; Ahmed, Dewan Hasan

2017-12-01

Phase change material (PCM) is widely known as latent heat storage. A comprehensive study is carried out to investigate the effect of PCM on heat transfer rate of building materials. Paraffin is used as PCM along with different conventional building materials to investigate the heat transfer rate from the heated region to the cold region. PCM is placed along with the three different types of building materials like plaster which is well know building material in urban areas and wood and straw which are commonly used in rural areas for roofing as well as wall panel material and investigated the heat transfer rate. An experimental setup was constructed with number of rectangular shape aluminum detachable casing (as cavity) and placed side by side. Series of rectangular cavity filled with convent ional building materials and PCM and these were placed in between two chambers filled with water at different temperature. Building materials and PCM were placed in different cavities with different combinations and investigated the heat transfer rate. The results show that using the PCM along with other building materials can be used to maintain lower temperature at the inner wall and chamber of the cold region. Moreover, the placement or orientation of the building materials and PCM make significant contribution to heat transfer rate from the heated zone to the cold zone.

GETTING TO THE HEART OF A GALAXY

NASA Technical Reports Server (NTRS)

2002-01-01

This collage of images in visible and infrared light reveals how the barred spiral galaxy NGC 1365 is feeding material into its central region, igniting massive star birth and probably causing its bulge of stars to grow. The material also is fueling a black hole in the galaxy's core. A galaxy's bulge is a central, football-shaped structure composed of stars, gas, and dust. The black-and-white image in the center, taken by a ground-based telescope, displays the entire galaxy. But the telescope's resolution is not powerful enough to reveal the flurry of activity in the galaxy's hub. The blue box in the galaxy's central region outlines the area observed by the NASA Hubble Space Telescope's visible-light camera, the Wide Field and Planetary Camera 2 (WFPC2). The red box pinpoints a narrower view taken by the Hubble telescope's infrared camera, the Near Infrared Camera and Multi-Object Spectrometer (NICMOS). A barred spiral is characterized by a lane of stars, gas, and dust slashing across a galaxy's central region. It has a small bulge that is dominated by a disk of material. The spiral arms begin at both ends of the bar. The bar is funneling material into the hub, which triggers star formation and feeds the bulge. The visible-light picture at upper left is a close-up view of the galaxy's hub. The bright yellow orb is the nucleus. The dark material surrounding the orb is gas and dust that is being funneled into the central region by the bar. The blue regions pinpoint young star clusters. In the infrared image at lower right, the Hubble telescope penetrates the dust seen in the WFPC2 picture to reveal more clusters of young stars. The bright blue dots represent young star clusters; the brightest of the red dots are young star clusters enshrouded in dust and visible only in the infrared image. The fainter red dots are older star clusters. The WFPC2 image is a composite of three filters: near-ultraviolet (3327 Angstroms), visible (5552 Angstroms), and near-infrared (8269 Angstroms). The NICMOS image, taken at a wavelength of 16,000 Angstroms, was combined with the visible and near-infrared wavelengths taken by WFPC2. The WFPC2 image was taken in January 1996; the NICMOS data were taken in April 1998. Credits for the ground-based image: Allan Sandage (The Observatories of the Carnegie Institution of Washington) and John Bedke (Computer Sciences Corporation and the Space Telescope Science Institute) Credits for the WFPC2 image: NASA and John Trauger (Jet Propulsion Laboratory) Credits for the NICMOS image: NASA, ESA, and C. Marcella Carollo (Columbia University)

Installation Restoration Program. Phase I - Records Search 92nd Bombardment Wing (Heavy), Fairchild AFB, Washington.

DTIC Science & Technology

1985-01-01

a pavillion with a snack bar, six cabins, eight recreational vehicle camping sites with electrical -- hookup only, a covered picnic area, and a small...solidification. Lava: The material extruded by a volcano which consists of molten or part- molten silicate material. Leachate: A solution resulting from

National Centers for Environmental Prediction

Science.gov Websites

Weather Service NWS logo - Click to go to the NWS homepage EMC Logo Navigation Bar Left Cap Home News TRAINING AND DOCUMENTATION MATERIALS: * WCOSS Transition Request Form (10/11/12) * WCOSS User Account Request Form has been added under 'Training and Documentation Materials' and will be used by all

Computational investigation of noble gas adsorption and separation by nanoporous materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, Mark D.; Sanders, Joseph C.; Greathouse, Jeffery A.

2008-10-01

Molecular simulations are used to assess the ability of metal-organic framework (MOF) materials to store and separate noble gases. Specifically, grand canonical Monte Carlo simulation techniques are used to predict noble gas adsorption isotherms at room temperature. Experimental trends of noble gas inflation curves of a Zn-based material (IRMOF-1) are matched by the simulation results. The simulations also predict that IRMOF-1 selectively adsorbs Xe atoms in Xe/Kr and Xe/Ar mixtures at total feed gas pressures of 1 bar (14.7 psia) and 10 bar (147 psia). Finally, simulations of a copper-based MOF (Cu-BTC) predict this material's ability to selectively adsorb Xemore » and Kr atoms when present in trace amounts in atmospheric air samples. These preliminary results suggest that Cu-BTC may be an ideal candidate for the pre-concentration of noble gases from air samples. Additional simulations and experiments are needed to determine the saturation limit of Cu-BTC for xenon, and whether any krypton atoms would remain in the Cu-BTC pores upon saturation.« less

Experimental Techniques for Evaluating the Effects of Aging on Impact and High Strain Rate Properties of Triaxial Braided Composite Materials

NASA Technical Reports Server (NTRS)

Pereira, J. Michael; Roberts, Gary D.; Ruggeri, Charles R.; Gilat, Amos; Matrka, Thomas

2010-01-01

An experimental program is underway to measure the impact and high strain rate properties of triaxial braided composite materials and to quantify any degradation in properties as a result of thermal and hygroscopic aging typically encountered during service. Impact tests are being conducted on flat panels using a projectile designed to induce high rate deformation similar to that experienced in a jet engine fan case during a fan blade-out event. The tests are being conducted on as-fabricated panels and panels subjected to various numbers of aging cycles. High strain rate properties are being measured using a unique Hopkinson bar apparatus that has a larger diameter than conventional Hopkinson bars. This larger diameter is needed to measure representative material properties because of the large unit cell size of the materials examined in this work. In this paper the experimental techniques used for impact and high strain rate testing are described and some preliminary results are presented for both as-fabricated and aged composites.

Peierls–Nabarro stresses of dislocations in monoclinic cyclotetramethylene tetranitramine (β-HMX)

NASA Astrophysics Data System (ADS)

Pal, Anirban; Picu, Catalin R.

2018-06-01

HMX (cyclotetramethylene tetranitramine) is an energetic material which releases substantial amounts of energy upon decomposition. The role of defects and deformation in causing reaction initiation was discussed in the literature but remains insufficiently understood. In this work, we identify, using computational methods, the slip systems which are potentially active in β-HMX and rank them in terms of their propensity for slip. To this end, we develop first a tentative ranking based on the degree of steric hindrance associated with slip. This is quantified using a geometric analog of the γ-surface. Further, we use atomistic models to compute the Peierls–Nabarro (PN) stress for the motion of dislocations in the slip systems with smallest degree of steric hindrance. A complex mechanical behavior is observed, including strong slip asymmetry, twinning and cleavage. The five systems with the lowest PN stress are (011)[01\\bar{1}], (011)[100], (101)[010], (101)[10\\bar{1}] and (021)[100]. We conclude that the material has enough slip systems available for supporting a generalized state of plastic strain provided the twinning system (101)[10\\bar{1}] is taken into consideration and that the resolved shear stress is at least 260 MPa.

Formation of Cu-type shear bands and their influence on deformation and texture of rolled f.c.c. {l_brace}112{r_brace}<111> single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, P.; Engler, O.; Luecke, K.

1995-10-01

Microstructural and textural evolution during rolling were investigated in (112)[11{bar 1}] single crystals of Al, Cu, and homogeneous supersaturated Al1.8wt%Cu. After a rolling degree of 30% the initial C-orientation (112)[11{bar 1}] of all three materials has rotated towards the so called D-orientation (4411)[1111{bar 8}]. While in the non-shear banding Al the D-orientation remains stable up to high rolling degrees, in the shear banding materials Cu and Al-Cu it rotates back to the initial C-orientation simultaneously with the formation of shear bands. This orientation change is explained by a rigid body rotation due to the special geometry of a deformation withmore » unidirectional shear bands. With the onset of shear band formation also strong orientation scatterings about the transverse direction appear in the pole figures. These scatterings are located inside the shear bands as well as their vicinity. They are due to the strong shear deformation and the resulting reaction stresses occurring in the shear bands and in their vicinity, respectively.« less

Development of fracture mechanics data for two hydrazine APU turbine wheel materials

NASA Technical Reports Server (NTRS)

Curbishley, G.

1975-01-01

The effects of high temperature, high pressure ammonia were measured on the fracture mechanics and fatigue properties of Astroloy and Rene' 41 turbine wheel materials. Also, the influence of protective coatings on these properties was investigated. Specimens of forged bar stock were subjected to LCF and HCF tests at 950 K (1250 F) and 3.4 MN/sq m (500 psig) pressure, in ammonia containing about 1.5 percent H2O. Aluminized samples (Chromizing Company's Al-870) and gold plated test bars were compared with uncoated specimens. Comparison tests were also run in air at 950 K (1250 F), but at ambient pressures. K sub IE and K sub TH were determined on surface flawed specimens in both the air and ammonia in both uncoated and gold plated conditions. Gold plated specimens exhibited better properties than uncoated samples, and aluminized test bars generally had lower properties. The fatigue properties of specimens tested in ammonia were higher than those tested in air, yet the K sub TH values of ammonia tested samples were lower than those tested in air. However, insufficient specimens were tested to develop significant design data.

Associations between fungal species and water-damaged building materials.

PubMed

Andersen, Birgitte; Frisvad, Jens C; Søndergaard, Ib; Rasmussen, Ib S; Larsen, Lisbeth S

2011-06-01

Fungal growth in damp or water-damaged buildings worldwide is an increasing problem, which has adverse effects on both the occupants and the buildings. Air sampling alone in moldy buildings does not reveal the full diversity of fungal species growing on building materials. One aim of this study was to estimate the qualitative and quantitative diversity of fungi growing on damp or water-damaged building materials. Another was to determine if associations exist between the most commonly found fungal species and different types of materials. More than 5,300 surface samples were taken by means of V8 contact plates from materials with visible fungal growth. Fungal identifications and information on building material components were analyzed using multivariate statistic methods to determine associations between fungi and material components. The results confirmed that Penicillium chrysogenum and Aspergillus versicolor are the most common fungal species in water-damaged buildings. The results also showed Chaetomium spp., Acremonium spp., and Ulocladium spp. to be very common on damp building materials. Analyses show that associated mycobiotas exist on different building materials. Associations were found between (i) Acremonium spp., Penicillium chrysogenum, Stachybotrys spp., Ulocladium spp., and gypsum and wallpaper, (ii) Arthrinium phaeospermum, Aureobasidium pullulans, Cladosporium herbarum, Trichoderma spp., yeasts, and different types of wood and plywood, and (iii) Aspergillus fumigatus, Aspergillus melleus, Aspergillus niger, Aspergillus ochraceus, Chaetomium spp., Mucor racemosus, Mucor spinosus, and concrete and other floor-related materials. These results can be used to develop new and resistant building materials and relevant allergen extracts and to help focus research on relevant mycotoxins, microbial volatile organic compounds (MVOCs), and microparticles released into the indoor environment.

NEWS: TRUMP resources

NASA Astrophysics Data System (ADS)

Swinbank, Elizabeth

2000-05-01

Support for astronomy in A-level physics aslogo Help is at hand for teachers and students choosing astronomy as part of A-level physics. The Teaching Resources Unit for Modern Physics (TRUMP) has produced a resource package covering all the astronomical options in the Edexcel, OCR and AQA (NEAB) syllabuses. The forerunner to TRUMP was the project that produced the highly successful Particle Physics Pack, sponsored by the Institute of Physics, which was instrumental in introducing particle physics into A-level syllabuses. The TRUMP Astrophysics Resource Package fills a gap between the colourful stimulus of popular materials on the one hand, and professional texts on the other. But this is not just another A-level textbook; the six-part resource pack has a similar structure and purpose to the Particle Physics Pack. It provides over 400 pages of comprehensive information for teachers, building on their existing subject knowledge and bringing them up to date as well as giving suggestions for teaching and notes on syllabus coverage. The package includes nearly 40 photocopiable sheets for students. The emphasis is on the physics that underpins the astronomy. There are details of student activities requiring no specialist equipment beyond that normally found in A-level labs, exercises using authentic data, and plenty of questions (all with worked solutions). The development of the TRUMP Astrophysics Package was funded by the Nuffield Foundation, the Particle Physics and Astronomy Research Council, the Institute of Physics and York University. The package is available by mail order, price £48 (inc. UK p&p) from the TRUMP Project, Science Education Group, University of York, Heslington, York YO10 5DD. Some parts may be purchased separately; for details contact the project's director, Elizabeth Swinbank (tel: 01904 434537, fax: 01904 434078, e-mail: es14@york.ac.uk) or consult the web page www.york.ac.uk/org/seg/trump. The BaBar experiment balogo In the spring of 1999, scientists began to collect data from the BaBar experiment - an international collaboration involving the UK, several other European countries and the USA. The experiment is designed to throw light on the puzzling question of why there is so little antimatter in the universe and so much matter. The TRUMP BaBar resource package brings the mystery of antimatter into schools. There are notes and colourful posters on the physics of BaBar, and photocopiable sheets supporting student activities. These include explorations of symmetry, templates for making a scale model of the BaBar detector, and a web-based research project. The pack is designed mainly for A-level physics (particularly those courses that include some particle physics) but parts also relate to GCSE science, Scottish Higher physics and Standard physics. The BaBar resource package is available free from the Particle Physics and Astronomy Research Council, which fully funded its development and production. Contact the Publicity Team, PPARC, Polaris House, North Star Avenue, Swindon, Wiltshire SN2 1SZ (tel: 01973 442123, e-mail: pr_pus@pparc.ac.uk).

[Smoke-free environment--nurse attitudes towards smoke-free regulations].

PubMed

Kaleta, Dorota; Polańska, Kinga; Dziankowska-Zaborszczyk, Elzbieta; Bak-Romaniszyn, Leokadia; Czarnecka, Karolina; Drygas, Wojciech

2009-01-01

The aim of the study was to analyze the nurse attitudes towards smoke-free regulations in public places. The study population consisted of 299 nurses. Among the study population questionnaire was conducted including socio-demographic characteristic, smoking and ETS profile, knowledge about health effects of smoking and abilities for conduction of antismoking counseling. Detail information was collected about nurse opinion on smoke-free public places such as offices, other workplaces, health and educational buildings, restaurants and bars. About 18% of study participants declared current tobacco smoking and 25% were former smokers. Almost all participating in the study women (85%-98%) are in favor of smoking ban in offices, health and educational buildings. 75% supported smoking ban in workplaces but 15% of them were somewhat opposed. Most of the nurses were in favor of smoke-free restaurants (64%) but they were less likely to support smoke-free bars, pubs and clubs (45%). Unfortunately 63% of interview women do not accept smoking ban in private cars. The percentage of women who support total ban of smoking in the presence of pregnant women was 93% and in the presence of children 79%. It is important to conduct educational and informational activities to increase public awareness on health consequences of active and passive smoking and the ways of elimination of such exposures.

Modular high power diode lasers with flexible 3D multiplexing arrangement optimized for automated manufacturing

NASA Astrophysics Data System (ADS)

Könning, Tobias; Bayer, Andreas; Plappert, Nora; Faßbender, Wilhelm; Dürsch, Sascha; Küster, Matthias; Hubrich, Ralf; Wolf, Paul; Köhler, Bernd; Biesenbach, Jens

2018-02-01

A novel 3-dimensional arrangement of mirrors is used to re-arrange beams from 1-D and 2-D high power diode laser arrays. The approach allows for a variety of stacking geometries, depending on individual requirements. While basic building blocks, including collimating optics, always remain the same, most adaptations can be realized by simple rearrangement of a few optical components. Due to fully automated alignment processes, the required changes can be realized in software by changing coordinates, rather than requiring customized mechanical components. This approach minimizes development costs due to its flexibility, while reducing overall product cost by using similar building blocks for a variety of products and utilizing a high grade of automation. The modules can be operated with industrial grade water, lowering overall system and maintenance cost. Stackable macro coolers are used as the smallest building block of the system. Each cooler can hold up to five diode laser bars. Micro optical components, collimating the beam, are mounted directly to the cooler. All optical assembly steps are fully automated. Initially, the beams from all laser bars propagate in the same direction. Key to the concept is an arrangement of deflectors, which re-arrange the beams into a 2-D array of the desired shape and high fill factor. Standard multiplexing techniques like polarization- or wavelengths-multiplexing have been implemented as well. A variety of fiber coupled modules ranging from a few hundred watts of optical output power to multiple kilowatts of power, as well as customized laser spot geometries like uniform line sources, have been realized.

Validation testing of shallow notched round-bar screening test specimens. [for the space shuttle main engine

NASA Technical Reports Server (NTRS)

Vroman, G. A.

1975-01-01

The capability of shallow-notched, round-bar, tensile specimens for screening critical environments as they affect the material fracture properties of the space shuttle main engine was tested and analyzed. Specimens containing a 0.050-inch-deep circumferential sharp notch were cyclically loaded in a 5000-psi hydrogen environment at temperatures of +70 and -15 F. Replication of test results and a marked change in cyclic life because of temperature variation demonstrated the validity of the specimen type to be utilized for screening tests.

Plant moisture stress: a portable freezing-point meter compared with the psychrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cary, J.W.; Fisher, H.D.

A small portable instrument for measuring the freezing-point depression of plant tissue has been developed for field use. The instrument is easy to operate and can be constructed from materials costing less than $100. Moisture stress measurements made with the freezing-point meter on a variety of plants were compared with vapor pressure psychrometer measurements. Variation between duplicates in the freezing point averaged 1.2 bars, but differences between stress measurements made with the psychrometer and freezing-point instrument averaged 2.6 bars. 11 references, 5 figures, 2 tables.

Surface topography and ordering-variant segregation in GaInP[sub 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedman, D.J.; Zhu, J.G.; Kibbler, A.E.

1993-09-27

Using transmission electron diffraction dark-field imaging, atomic force microscopy (AFM), and Nomarski microscopy, we demonstrate a direct connection between surface topography and cation site ordering in GaInP[sub 2]. We study epilayers grown by organometallic vapor-phase epitaxy on GaAs substrates oriented 2[degree] off (100) towards (110). Nomarski microscopy shows that, as growth proceeds, the surface of ordered material forms faceted structures aligned roughly along [011]. A comparison with the dark-field demonstrates that the [1[bar 1]1] and [11[bar 1

Optimum Installation of Sorptive Building Materials Using Contribution Ratio of Pollution Source for Improvement of Indoor Air Quality.

PubMed

Park, Seonghyun; Seo, Janghoo

2016-04-01

Reinforcing the insulation and airtightness of buildings and the use of building materials containing new chemical substances have caused indoor air quality problems. Use of sorptive building materials along with removal of pollutants, constant ventilation, bake-out, etc. are gaining attention in Korea and Japan as methods for improving such indoor air quality problems. On the other hand, sorptive building materials are considered a passive method of reducing the concentration of pollutants, and their application should be reviewed in the early stages. Thus, in this research, activated carbon was prepared as a sorptive building material. Then, computational fluid dynamics (CFD) was conducted, and a method for optimal installation of sorptive building materials was derived according to the indoor environment using the contribution ratio of pollution source (CRP) index. The results show that a method for optimal installation of sorptive building materials can be derived by predicting the contribution ratio of pollutant sources according to the CRP index.

Precast concrete unit assessment through GPR survey and FDTD modelling

NASA Astrophysics Data System (ADS)

Campo, Davide

2017-04-01

Precast concrete elements are widely used within United Kingdom house building offering ease in assembly and added values as structural integrity, sound and thermal insulation; most common concrete components include walls, beams, floors, panels, lintels, stairs, etc. The lack of respect of the manufacturer instruction during assembling, however, may induce cracking and short/long term loss of bearing capacity. GPR is a well-established not destructive technique employed in the assessment of structural elements because of real-time imaging, quickness of data collecting and ability to discriminate finest structural details. In this work, GPR has been used to investigate two different precast elements: precast reinforced concrete planks constituting the roof slab of a school and precast wood-cement blocks with insulation material pre-fitted used to build a perimeter wall of a private building. Visible cracks affected both constructions. For the assessment surveys, a GSSI 2.0 GHz GPR antenna has been used because of the high resolution required and the small size of the antenna case (155 by 90 by 105mm) enabling scanning up to 45mm from any obstruction. Finite Difference Time Domain (FDTD) numerical modelling was also performed to build a scenario of the expected GPR signal response for a preliminary real-time interpretation and to help solve uncertainties due to complex reflection patterns: simulated radargrams were built using Reflex Software v. 8.2, reproducing the same GPR pulse used for the surveys in terms of wavelet, nominal frequency, sample frequency and time window. Model geometries were derived from the design projects available both for the planks and the blocks; the electromagnetic properties of the materials (concrete, reinforcing bars, air-filled void, insulation and wooden concrete) were inferred from both values reported in literature and a preliminary interpretation of radargrams where internal layer interfaces were clearly recognizable and univocally interpretable. Simulated and real radargrams comparison demonstrated that, in both cases, manufacturer instructions were not fully respected and confirmed GPR as a fast and effective structural assessment technique with the support of FDTD modelling as data interpretation validating method when complex reflection patterns are observed. GPR findings will be then used to address the intrusive coring necessary to evaluate the compressive strength of the concrete and, in synergy with the intrusive survey results, to plan properly corrective actions to ensure the stability of the structures and guarantee the usability.

Design Producibility Assessment System

DTIC Science & Technology

1989-06-30

Data Base Material Code 17 - 4PH Manufactu Description Precipitation-Handling, corrosion-resist steel Strategic? No Strip Sheet Bar Wire Tube Yes Yes Yes...planned production quantity: 10000 PRODUCTION FACILITIES 5 Select the design material: 17 - 4PH <PgUp> Page Up, <PgDn> Page Down, <Fl> Help, <Esc> Exit DPAS...vl.00 Saturday June 17 , 1989 11:06 am Design Producibility Assessment System Select the design material: 17 - 4PH Select the design material’s form

Graphene oxide-based benzimidazole-crosslinked networks for high-performance supercapacitors.

PubMed

Cui, Yi; Cheng, Qian-Yi; Wu, Haiping; Wei, Zhixiang; Han, Bao-Hang

2013-09-21

The synthesis of graphene oxide (GO)-based benzimidazole-crosslinked network (GOBIN) materials is presented. These materials are prepared by the covalent crosslinking of GO sheets using a condensation reaction between the carboxylic acid moieties on the GO surface and the o-aminophenyl end groups of 3,3'-diaminobenzidine (or 1,2,4,5-benzenetetraamine tetrahydrochloride). An efficient one-pot catalyst- and template-free synthesis was performed. The obtained porous GO-based materials possess a Brunauer-Emmett-Teller specific surface area ranging from 260 to 920 m(2) g(-1). Electrochemical testing indicates that the GOBIN materials display a specific capacitance up to 370 F g(-1) at a current density of 0.1 A g(-1) and about 90% of the original capacitance is retained after 5000 cycles at a current density of 3 A g(-1). Therefore, GOBIN materials can be employed as promising electrode materials for high-performance supercapacitors with outstanding cycling stability. Furthermore, owing to their significantly high specific surface area, these materials also show hydrogen uptake (up to 1.24 wt%, at 77 K and 1.0 bar) and carbon dioxide capture (up to 14.2 wt%, at 273 K and 1.0 bar) properties. As a result, these GO-based porous materials improve both the supercapacitor performance and gas sorption property, which demonstrate an excellent performance in the practical application of energy storage.

29 CFR 779.355 - Classification of lumber and building materials sales.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 3 2012-07-01 2012-07-01 false Classification of lumber and building materials sales. 779... Service Establishments Lumber and Building Materials Dealers § 779.355 Classification of lumber and building materials sales. (a) General. In determining, for purposes of the section 13(a)(2) and (4...

29 CFR 779.355 - Classification of lumber and building materials sales.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 3 2013-07-01 2013-07-01 false Classification of lumber and building materials sales. 779... Service Establishments Lumber and Building Materials Dealers § 779.355 Classification of lumber and building materials sales. (a) General. In determining, for purposes of the section 13(a)(2) and (4...

29 CFR 779.355 - Classification of lumber and building materials sales.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 3 2014-07-01 2014-07-01 false Classification of lumber and building materials sales. 779... Service Establishments Lumber and Building Materials Dealers § 779.355 Classification of lumber and building materials sales. (a) General. In determining, for purposes of the section 13(a)(2) and (4...

Lung Injury Pathways: Adenosine Receptor 2B Signaling Limits Development of Ischemic Bronchiolitis Obliterans Organizing Pneumonia

PubMed Central

Densmore, John C.; Schaid, Terry R.; Jeziorczak, Paul M.; Medhora, Meetha; Audi, Said; Nayak, Shraddha; Auchampach, John; Dwinell, Melinda R.; Geurts, Aron M.; Jacobs, Elizabeth R.

2018-01-01

Purpose/Aim of the study Adenosine signaling was studied in bronchiolitis obliterans organizing pneumonia (BOOP) resulting from unilateral lung ischemia. Materials and Methods Ischemia was achieved by either left main pulmonary artery or complete hilar ligation. Sprague Dawley (SD) rats, Dahl salt sensitive (SS) rats and SS mutant rat strain containing a mutation in the A2B adenosine receptor gene (Adora2b) were studied. Adenosine concentrations were measured in bronchoalveolar lavage (BAL) by HPLC. A2A (A2AAR) and A2B adenosine receptor (A2BAR) mRNA and protein were quantified. Results 24h after unilateral PA ligation, BAL adenosine concentrations from ischemic lungs were increased relative to contralateral lungs in SD rats. A2BAR mRNA and protein concentrations were increased after PA ligation while miR27a, a negatively regulating microRNA, was decreased in ischemic lungs. A2AAR mRNA and protein concentrations remained unchanged following ischemia. A2BAR protein was increased in PA ligated lungs of SS rats after 7d, and 4h after complete hilar ligation in SD rats. SS-Adora2b mutants showed a greater extent of BOOP relative to SS rats, and greater inflammatory changes. Conclusions Increased A2BAR and adenosine following unilateral lung ischemia as well as more BOOP in A2BAR mutant rats implicate a protective role for A2BAR signaling in countering ischemic lung injury. PMID:28266889

Spectral narrowing of a 980 nm tapered diode laser bar

NASA Astrophysics Data System (ADS)

Vijayakumar, Deepak; Jensen, Ole Bjarlin; Lucas Leclin, Ga"lle; Petersen, Paul Michael; Thestrup, Birgitte

2011-03-01

High power diode laser bars are interesting in many applications such as solid state laser pumping, material processing, laser trapping, laser cooling and second harmonic generation. Often, the free running laser bars emit a broad spectrum of the order of several nanometres which limit their scope in wavelength specific applications and hence, it is vital to stabilize the emission spectrum of these devices. In our experiment, we describe the wavelength narrowing of a 12 element 980 nm tapered diode laser bar using a simple Littman configuration. The tapered laser bar which suffered from a big smile has been "smile corrected" using individual phase masks for each emitter. The external cavity consists of the laser bar, both fast and slow axis micro collimators, smile correcting phase mask, 6.5x beam expanding lens combination, a 1200 lines/mm reflecting grating with 85% efficiency in the first order, a slow axis focusing cylindrical lens of 40 mm focal length and an output coupler which is 10% reflective. In the free running mode, the laser emission spectrum was 5.5 nm wide at an operating current of 30A. The output power was measured to be in excess of 12W. Under the external cavity operation, the wavelength spread of the laser could be limited to 0.04 nm with an output power in excess of 8 W at an operating current of 30A. The spectrum was found to be tuneable in a range of 16 nm.

Associations between Fungal Species and Water-Damaged Building Materials ▿

PubMed Central

Andersen, Birgitte; Frisvad, Jens C.; Søndergaard, Ib; Rasmussen, Ib S.; Larsen, Lisbeth S.

2011-01-01

Fungal growth in damp or water-damaged buildings worldwide is an increasing problem, which has adverse effects on both the occupants and the buildings. Air sampling alone in moldy buildings does not reveal the full diversity of fungal species growing on building materials. One aim of this study was to estimate the qualitative and quantitative diversity of fungi growing on damp or water-damaged building materials. Another was to determine if associations exist between the most commonly found fungal species and different types of materials. More than 5,300 surface samples were taken by means of V8 contact plates from materials with visible fungal growth. Fungal identifications and information on building material components were analyzed using multivariate statistic methods to determine associations between fungi and material components. The results confirmed that Penicillium chrysogenum and Aspergillus versicolor are the most common fungal species in water-damaged buildings. The results also showed Chaetomium spp., Acremonium spp., and Ulocladium spp. to be very common on damp building materials. Analyses show that associated mycobiotas exist on different building materials. Associations were found between (i) Acremonium spp., Penicillium chrysogenum, Stachybotrys spp., Ulocladium spp., and gypsum and wallpaper, (ii) Arthrinium phaeospermum, Aureobasidium pullulans, Cladosporium herbarum, Trichoderma spp., yeasts, and different types of wood and plywood, and (iii) Aspergillus fumigatus, Aspergillus melleus, Aspergillus niger, Aspergillus ochraceus, Chaetomium spp., Mucor racemosus, Mucor spinosus, and concrete and other floor-related materials. These results can be used to develop new and resistant building materials and relevant allergen extracts and to help focus research on relevant mycotoxins, microbial volatile organic compounds (MVOCs), and microparticles released into the indoor environment. PMID:21531835

Advanced electromagnetic methods for aerospace vehicles

NASA Technical Reports Server (NTRS)

Balanis, Constantine A.; Sun, Weimin; El-Sharawy, El-Budawy; Aberle, James T.; Birtcher, Craig R.; Peng, Jian; Tirkas, Panayiotis A.; Kokotoff, David; Zavosh, Frank

1993-01-01

The Advanced Helicopter Electromagnetics (AHE) Industrial Associates Program has continuously progressed with its research effort focused on subjects identified and recommended by the Advisory Task Force of the program. The research activities in this reporting period have been steered toward practical helicopter electromagnetic problems, such as HF antenna problems and antenna efficiencies, recommended by the AHE members at the annual conference held at Arizona State University on 28-29 Oct. 1992 and the last biannual meeting held at the Boeing Helicopter on 19-20 May 1993. The main topics addressed include the following: Composite Materials and Antenna Technology. The research work on each topic is closely tied with the AHE Consortium members' interests. Significant progress in each subject is reported. Special attention in the area of Composite Materials has been given to the following: modeling of material discontinuity and their effects on towel-bar antenna patterns; guidelines for composite material modeling by using the Green's function approach in the NEC code; measurements of towel-bar antennas grounded with a partially material-coated plate; development of 3-D volume mesh generator for modeling thick and volumetric dielectrics by using FD-TD method; FDTD modeling of horn antennas with composite E-plane walls; and antenna efficiency analysis for a horn antenna loaded with composite dielectric materials.

Multilayer diffraction grating

DOEpatents

Barbee, T.W. Jr.

1990-04-10

This invention is for a reflection diffraction grating that functions at X-ray to VUV wavelengths and at normal angles of incidence. The novel grating is comprised of a laminar grating of period D with flat-topped grating bars. A multiplicity of layered synthetic microstructures, of period d and comprised of alternating flat layers of two different materials, are disposed on the tops of the grating bars of the laminar grating. In another embodiment of the grating, a second multiplicity of layered synthetic microstructures are also disposed on the flat faces, of the base of the grating, between the bars. D is in the approximate range from 3,000 to 50,000 Angstroms, but d is in the approximate range from 10 to 400 Angstroms. The laminar grating and the layered microstructures cooperatively interact to provide many novel and beneficial instrumentational advantages. 2 figs.

Multilayer diffraction grating

DOEpatents

Barbee, Jr., Troy W.

1990-01-01

This invention is for a reflection diffraction grating that functions at X-ray to VUV wavelengths and at normal angles of incidence. The novel grating is comprised of a laminar grating of period D with flat-topped grating bars. A multiplicity of layered synthetic microstructures, of period d and comprised of alternating flat layers of two different materials, are disposed on the tops of the grating bars of the laminar grating. In another embodiment of the grating, a second multiplicity of layered synthetic microstructures are also disposed on the flat faces, of the base of the grating, between the bars. D is in the approximate range from 3,000 to 50,000 Angstroms, but d is in the approximate range from 10 to 400 Angstroms. The laminar grating and the layered microstructures cooperatively interact to provide many novel and beneficial instrumentational advantages.

Combined experimental and numerical approach to evaluate impact scaling relations and reproducibility of craters produced at the Experimental Projectile Impact Chamber (E.P.I.C., Centro de Astrobiología, Spain.)

NASA Astrophysics Data System (ADS)

Ormö, J.; Wünnemann, K.; Collins, G.; Melero Asensio, I.

2012-04-01

The Experimental Projectile Impact Chamber at Centro de Astrobiología, Spain, consists of a 7m wide, funnel-shaped test bed, and a 20.5mm caliber compressed N2 gas gun. The test bed can be filled with any type of target material, but is especially designed for wet target experiments. The shape and size aim to decrease disturbance from reflected surface waves in wet target experiments. Experiments are done under 1Atm pressure. The gas gun can launch projectiles of any material and dimensions <20mm (smaller diameters using sabots), and at any angle from vertical to near horizontal. The projectile velocities are of the order of a few hundreds of meters per second depending mainly on the gas pressure, as well as projectile diameter and density. When using a dry sand target a transient crater about 30cm wide is produced. Wet target experiments have not yet been performed in this newly installed test chamber, but transient cavities in water are expected to be in the order of 50-70cm wide. The large scale allows for detailed study of the dynamics of cratering motions during the stages of crater growth and subsequent collapse, especially in wet targets. These observations provide valuable benchmark data for numerical simulations and for comparison with field studies. Here we describe the results of ten impact experiments using three different gas pressures (100bar, 180bar, 200bar), two projectile compositions (20mm, 5.7g delrin; 20mm, 16.3g Al2O3), and two different impact angles (90˚ and 53˚ over the horizontal plane). Nine of the experiments were done in a quarter-space geometry using a specially designed camera tank with a 45mm thick glass window. One experiment was done in half-space geometry as reference. The experiments were recorded with a high-speed digital video camera, and the resulting craters were documented with a digital still frame camera. Projectile velocities are estimated with a combination of tracking software and a Shooting Chrony Alpha M-1 chronograph to be about 330m/s for delrin (100bar), 220m/s for Al2O3 (100bar), 400m/s for delrin (200bar), and 275m/s for Al2O3 (200bar). The velocities for the lighter delrin projectile and at the higher pressure are above the speed of sound in dry silica sand (243 m/s; Sandia report SAND2007-3524). The experimental set up (i.e. target material, projectile density and velocity, impact angle), as well as the dimensions of the resulting craters, are used as inputs in numerical simulation using the iSALE computational code. Results from these simulations will be presented and compared with the experiments.

Advanced Experimental Methods for Low-temperature Magnetotransport Measurement of Novel Materials

PubMed Central

Hagmann, Joseph A.; Le, Son T.; Richter, Curt A.; Seiler, David G.

2016-01-01

Novel electronic materials are often produced for the first time by synthesis processes that yield bulk crystals (in contrast to single crystal thin film synthesis) for the purpose of exploratory materials research. Certain materials pose a challenge wherein the traditional bulk Hall bar device fabrication method is insufficient to produce a measureable device for sample transport measurement, principally because the single crystal size is too small to attach wire leads to the sample in a Hall bar configuration. This can be, for example, because the first batch of a new material synthesized yields very small single crystals or because flakes of samples of one to very few monolayers are desired. In order to enable rapid characterization of materials that may be carried out in parallel with improvements to their growth methodology, a method of device fabrication for very small samples has been devised to permit the characterization of novel materials as soon as a preliminary batch has been produced. A slight variation of this methodology is applicable to producing devices using exfoliated samples of two-dimensional materials such as graphene, hexagonal boron nitride (hBN), and transition metal dichalcogenides (TMDs), as well as multilayer heterostructures of such materials. Here we present detailed protocols for the experimental device fabrication of fragments and flakes of novel materials with micron-sized dimensions onto substrate and subsequent measurement in a commercial superconducting magnet, dry helium close-cycle cryostat magnetotransport system at temperatures down to 0.300 K and magnetic fields up to 12 T. PMID:26863449

High temperature, low cycle fatigue of copper-base alloys in argon. Part 3: Zirconium-copper; thermal-mechanical strain cycling, hold-time and notch fatigue results

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1973-01-01

The low-cycle fatigue characteristics of smooth bar and notched bar specimens (hourglass shape) of zirconium-copper, 1/2 Hard, material (R-2 Series) were evaluated at room temperature in axial strain control. Over the fatigue life range from about 300 to 3000 cycles the ratio of fatigue life for smooth bar to fatigue life for notched bar remained constant at a value of about 6.0. Some additional hold-time data for the R-2 alloy tested in argon at 538 C are reported. An analysis of the relaxation data obtained in these hold-time tests is also reported and it is shown that these data yield a fairly consistent correlation in terms of instantaneous stress rate divided by instantaneous stress. Two thermal-mechanical strain cycling tests were also performed using a cyclic frequency of 4.5 cycles per hour and a temperature cycling interval from 260 to 538 C. The fatigue life values in these tests were noticeably lower than that observed in isothermal tests at 538 C.

Buoyancy of gas-filled bladders at great depth

NASA Astrophysics Data System (ADS)

Priede, Imants G.

2018-02-01

At high hydrostatic pressures exceeding 20 MPa or 200 bar, equivalent to depths exceeding ca.2000 m, the behaviour of gases deviates significantly from the predictions of standard equations such as Boyle's Law, the Ideal Gas Law and Van der Waals equation. The predictions of these equations are compared with experimental data for nitrogen, oxygen and air at 0 °C and 15 °C, at pressures up to 1100 bar (110 MPa) equivalent to full ocean depth of ca. 11000 m. Owing to reduced compressibility of gases at high pressures, gas-filled bladders at full ocean depth have a density of 847 kg m-3 for Oxygen, 622 kg m-3 for Nitrogen and 660 kg m-3 for air providing potentially useful buoyancy comparable with that available from man-made materials. This helps explain why some of the deepest-living fishes at ca. 7000 m depth (700 bar or 70 MPa) have gas-filled swim bladders. A table is provided of the density and buoyancy of oxygen, nitrogen and air at 0 °C and 15 °C from 100 to 1100 bar.

Activity measurement and effective dose modelling of natural radionuclides in building material.

PubMed

Maringer, F J; Baumgartner, A; Rechberger, F; Seidel, C; Stietka, M

2013-11-01

In this paper the assessment of natural radionuclides' activity concentration in building materials, calibration requirements and related indoor exposure dose models is presented. Particular attention is turned to specific improvements in low-level gamma-ray spectrometry to determine the activity concentration of necessary natural radionuclides in building materials with adequate measurement uncertainties. Different approaches for the modelling of the effective dose indoor due to external radiation resulted from natural radionuclides in building material and results of actual building material assessments are shown. Copyright © 2013 Elsevier Ltd. All rights reserved.

A new accurate and flexible index to assess the contribution of building materials to indoor gamma exposure.

PubMed

Nuccetelli, Cristina; Leonardi, Federica; Trevisi, Rosabianca

2015-05-01

The role of building materials as a source of gamma radiation has been recognized in the new EU Basic Safety Standards Directive which introduces an index I to screen building materials of radiological concern. This index was developed to account for average concrete values of thickness and density, the main structural characteristics of building materials that have an effect on gamma irradiation. Consequently, this screening procedure could be unfit in case of significantly different density and/or thickness of the building materials under examination. The paper proposes a more accurate and flexible activity concentration index, accounting for the actual density and thickness of building materials. Copyright © 2015 Elsevier Ltd. All rights reserved.

Natural radioactivity measurements of building materials in Baotou, China.

PubMed

Zhao, Caifeng; Lu, Xinwei; Li, Nan; Yang, Guang

2012-12-01

Natural radioactivity due to (226)Ra, (232)Th and (40)K in the common building materials collected from Baotou city of Inner Mongolia, China was measured using gamma-ray spectrometry. The radiation hazard of the studied building materials was estimated by the radium equivalent activity (Ra(eq)), internal hazard index (H(in)) and annual effective dose (AED). The concentrations of the natural radionuclides and Ra(eq) in the studied samples were compared with the corresponding results of other countries. The Ra(eq) values of the building materials are below the internationally accepted values (370 Bq kg(-1)). The values of H(in) in all studied building materials are less than unity. The AEDs of all measured building materials are at an acceptable level.

78 FR 59677 - Environmental Impacts Statements; Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-27

..., Designation of the Atchafalaya River Bar Channel Ocean Dredged Material Disposal Site, Review Period Ends: 10.../2013, Contact: Paul Bradford 406-293-6211. EIS No. 20130282, Final EIS, USFS, WY, Clinker Mining...

Radio Frequency Identification Applications in Pavements

DOT National Transportation Integrated Search

2014-08-01

Radio frequency identification (RFID) technology is widely used for inventory control, tool and material tracking, and other similar applications where line-of-sight optical bar codes are inconvenient or impractical. Several applications of RFID tech...

40 CFR 227.13 - Dredged materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... municipal or industrial wastes or by runoff from terrestrial sources such as agricultural lands. (b) Dredged... energy such as streams with large bed loads or coastal areas with shifting bars and channels; or (2...

40 CFR 227.13 - Dredged materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... municipal or industrial wastes or by runoff from terrestrial sources such as agricultural lands. (b) Dredged... energy such as streams with large bed loads or coastal areas with shifting bars and channels; or (2...

40 CFR 227.13 - Dredged materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... municipal or industrial wastes or by runoff from terrestrial sources such as agricultural lands. (b) Dredged... energy such as streams with large bed loads or coastal areas with shifting bars and channels; or (2...

An analysis of star formation with Herschel in the Hi-GAL Survey. II. The tips of the Galactic bar

NASA Astrophysics Data System (ADS)

Veneziani, M.; Schisano, E.; Elia, D.; Noriega-Crespo, A.; Carey, S.; Di Giorgio, A.; Fukui, Y.; Maiolo, B. M. T.; Maruccia, Y.; Mizuno, A.; Mizuno, N.; Molinari, S.; Mottram, J. C.; Moore, T. J. T.; Onishi, T.; Paladini, R.; Paradis, D.; Pestalozzi, M.; Pezzuto, S.; Piacentini, F.; Plume, R.; Russeil, D.; Strafella, F.

2017-03-01

Context. We present the physical and evolutionary properties of prestellar and protostellar clumps in the Herschel Infrared GALactic plane survey (Hi-GAL) in two large areas centered in the Galactic plane and covering the tips of the long Galactic bar at the intersection with the spiral arms. The areas fall in the longitude ranges 19° <ℓ < 33° and 340° < ℓ < 350°, while latitude is -1° < b < 1°. Newly formed high mass stars and prestellar objects are identified and their properties derived and compared. A study is also presented on five giant molecular complexes at the further edge of the bar, identified through ancillary 12CO(1-0) data from the NANTEN observatory. Aims: One of the goals of this analysis is assessing the role of spiral arms in the star-formation processes in the Milky Way. It is, in fact, still a matter of debate if the particular configuration of the Galactic rotation and potential at the tips of the bar can trigger star formation. Methods: The star-formation rate was estimated from the quantity of proto-stars expected to form during the collapse of massive turbulent clumps into star clusters. The expected quantity of proto-stars was estimated by the possible final cluster configurations of a given initial turbulent clump. This new method was developed by applying a Monte Carlo procedure to an evolutionary model of turbulent cores and takes into account the wide multiplicity of sources produced during the collapse. Results: The star-formation rate density values at the tips are 1.2±0.3×10-3 M_⊙/{yr kpc^2} and 1.5±0.3×10-3 M_⊙/{yr kpc^2} in the first and fourth quadrant, respectively. The same values estimated on the entire field of view, that is including the tips of the bar and background and foreground regions, are 0.9±0.2×10-3 M_⊙/{yr kpc^2} and 0.8±0.2×10-3 M_⊙/{yr kpc^2}. The conversion efficiency indicates the percentage amount of material converted into stars and is approximately 0.8% in the first quadrant and 0.5% in the fourth quadrant, and does not show a significant difference in proximity of the bar. The star forming regions identified through CO contours at the further edge of the bar show star-formation rate and star-formation rate densities larger than the surrounding regions but their conversion efficiencies are comparable. Conclusions: The tips of the bar show an enhanced star-formation rate with respect to background and foreground regions. However, the conversion efficiency shows little change across the observed fields suggesting that the star-formation activity at the bar is due to a large amount of dust and molecular material rather than being due to a triggering process.

Chemical composition of Juniperus communis L. fruits supercritical CO2 extracts: dependence on pressure and extraction time.

PubMed

Barjaktarović, Branislava; Sovilj, Milan; Knez, Zeljko

2005-04-06

Ground fruits of the common juniper (Juniperus communis L.), with a particle size range from 0.250-0.400 mm, forming a bed of around 20.00 +/- 0.05 g, were extracted with supercritical CO(2) at pressures of 80, 90, and 100 bars and at a temperature of 40 degrees C. The total amount of extractable substances or global yield (mass of extract/mass of raw material) for the supercritical fluid extraction process varied from 0.65 to 4.00% (wt). At each investigated pressure, supercritical CO(2) extract fractions collected in successive time intervals over the course of the extraction were analyzed by capillary gas chromatography, using flame ionization (GC-FID) and mass spectrometric detection (GC-MS). More than 200 constituents were detected in the extracts, and the contents of 50 compounds were reported in the work. Dependence of the percentage yields of monoterpene, sesquiterpene, oxygenated monoterpene, and oxygenated sesquiterpene hydrocarbon groups on the extraction time was investigated, and conditions that favored the yielding of each terpene groups were emphasized. At all pressures, monoterpene hydrocarbons were almost completely extracted from the berries in the first 0.6 h. It was possible to extract oxygenated monoterpenes at 100 bar in 0.5 h and at 90 bar in 1.2 h. Contrary to that, during an extraction period of 4 h at 80 bar, it was possible to extract only 75% of the maximum yielded value of oxygenated monoterpene at 100 bar. Intensive extraction of sesquiterpenes could be by no means avoided at any pressure, but at the beginning of the process (the first 0.5 h) at 80 bar, they were extracted about 8 and 3 times slower than at 100 and 90 bar, respectively. Oxygenated sesquiterpenes were yielded at fast, constant extraction rates at 100 and 90 bar in 1.2 and 3 h, respectively. This initial fast extraction period was consequently followed by much slower extraction of oxygenated sesquiterpenes.

Energy history of the United States 1776 to 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1975-01-01

A bicentennial energy wall chart and accompanying manual depict the history of U.S. energy use since 1776. Color bars for wood, coal, animal energy, wind and water power, gaseous and liquid fuels, electricity, solar energy, geothermal energy, and nuclear fuels help tie specific historical events with energy sources. The color bars are arranged vertically in a year-by-year chronology and horizontally by decades. Projections to the year 2001 predict the uses and technologies of each energy source and the possibility of new discoveries. One section of the chart graphically cites the relationship of territorial expansion and energy history, energy consumption andmore » end use, the substitution of one energy source for another, and conversion from one form to another. The chart can be used to trace specific themes, such as Joseph Henry's invention of the electric motor in 1826 to the projection of building-size storage batteries for future city needs. (DCK)« less

Estimation of reliability and dynamic property for polymeric material at high strain rate using SHPB technique and probability theory

NASA Astrophysics Data System (ADS)

Kim, Dong Hyeok; Lee, Ouk Sub; Kim, Hong Min; Choi, Hye Bin

2008-11-01

A modified Split Hopkinson Pressure Bar technique with aluminum pressure bars and a pulse shaper technique to achieve a closer impedance match between the pressure bars and the specimen materials such as hot temperature degraded POM (Poly Oxy Methylene) and PP (Poly Propylene). The more distinguishable experimental signals were obtained to evaluate the more accurate dynamic deformation behavior of materials under a high strain rate loading condition. A pulse shaping technique is introduced to reduce the non-equilibrium on the dynamic material response by modulation of the incident wave during a short period of test. This increases the rise time of the incident pulse in the SHPB experiment. For the dynamic stress strain curve obtained from SHPB experiment, the Johnson-Cook model is applied as a constitutive equation. The applicability of this constitutive equation is verified by using the probabilistic reliability estimation method. Two reliability methodologies such as the FORM and the SORM have been proposed. The limit state function(LSF) includes the Johnson-Cook model and applied stresses. The LSF in this study allows more statistical flexibility on the yield stress than a paper published before. It is found that the failure probability estimated by using the SORM is more reliable than those of the FORM/ It is also noted that the failure probability increases with increase of the applied stress. Moreover, it is also found that the parameters of Johnson-Cook model such as A and n, and the applied stress are found to affect the failure probability more severely than the other random variables according to the sensitivity analysis.

VIEW OF THE INSTALLATION OF AN EXTRUSION PRESS IN THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF THE INSTALLATION OF AN EXTRUSION PRESS IN THE HIGH BAY AREA OF BUILDING 865. THE EXTRUSION PRESS WAS USED TO PRODUCE CYLINDRICAL BARS, HOLLOW TUBES, AND SHAPES WITH IRREGULAR CROSS-SECTIONS BY FORCING PREHEATED METAL THROUGH A DIE ORIFICE UNDER HIGH PRESSURE. (5/22/70) - Rocky Flats Plant, Metal Research & Development Laboratory, South of Central Avenue at south end of terminus of Ninth Avenue, Golden, Jefferson County, CO

New Titan Saltation Threshold Experiments: Investigating Current and Past Climates

NASA Astrophysics Data System (ADS)

Bridges, N.; Burr, D. M.; Marshall, J.; Smith, J. K.; Emery, J. P.; Horst, S. M.; Nield, E.; Yu, X.

2015-12-01

Titan exhibits aeolian sand dunes that cover ~20% of its surface, attesting to significant sediment transport by the wind. Recent experiments in the Titan Wind Tunnel (TWT) at NASA Ames Research Center [1,2] found that the threshold friction speed needed to detach Titanian "sand" is about 50% higher than previous estimates based on theory alone [3], a result that might be explained by the low ratio of particle to fluid density on the body [1]. Following the successful completion of the initial Titan threshold tests, we are conducting new experiments that expand the pressure range above and below current Titan values. The basic experimental techniques are described in [1], with minor updates to the instrumentation as described in [2]. To reproduce the kinematic viscosity and particle friction Reynolds number equivalent to that expected for Titan's nitrogen atmosphere at 1.4 bars and 94 K requires that TWT be pressurized to 12.5 bars for air at 293K. In addition to running experiments at this pressure to reproduce previous results [1] and investigate low density (high density ratio) materials, TWT pressures of 3 and 8 bars are in the experimental matrix to understand threshold under past Titan conditions when the atmospheric pressure may have been lower [4]. Higher pressures, at 15 and 20 bars in TWT, are also being run to understand the putative effects of low density ratio conditions. Our experimental matrix for this follow-on work uses some of the same materials as previously used, including walnut shells, basalt, quartz, glass spheres, and various low density materials to better simulate the gravity-equivalent weight of Titan sand. For these experiments, the TWT is now equipped with a new high pressure Tavis transducer with sufficient sensitivity to measure freestream speeds of less than 0.5 m s-1 at 12.5 bars. New techniques include video documentation of the experiments. We are also investigating methods of measuring humidity of the wind tunnel environment and electrostatic forces to assess their effect on threshold. [1] Burr, D.M. et al. [2015], Nature, 517, 60-67. [2] Burr, D.M. et al. [2015], Aeolian Res., in press [3] Iversen, J.D. and B.R. White (1982), Sedimentology, 29, 111-119. [4] Charnay, B. et al. [2014], Icarus, 241, 269-279.

Finite element analysis of composite beam-to-column connection with cold-formed steel section

NASA Astrophysics Data System (ADS)

Firdaus, Muhammad; Saggaff, Anis; Tahir, Mahmood Md

2017-11-01

Cold-formed steel (CFS) sections are well known due to its lightweight and high structural performance which is very popular for building construction. Conventionally, they are used as purlins and side rails in the building envelopes of the industrial buildings. Recent research development on cold-formed steel has shown that the usage is expanded to the use in composite construction. This paper presents the modelling of the proposed composite connection of beam-to-column connection where cold-formed steel of lipped steel section is positioned back-to-back to perform as beam. Reinforcement bars is used to perform the composite action anchoring to the column and part of it is embedded into a slab. The results of the finite element and numerical analysis has showed good agreement. The results show that the proposed composite connection contributes to significant increase to the moment capacity.

Design and feasibility of integrating personalized PRO dashboards into prostate cancer care

PubMed Central

Izard, Jason P; Dalkin, Bruce L; Mikles, Sean P; Gore, John L

2016-01-01

Objective Patient-reported outcomes (PROs) are a valued source of health information, but prior work focuses largely on data capture without guidance on visual displays that promote effective PRO use in patient-centered care. We engaged patients, providers, and design experts in human-centered design of “PRO dashboards” that illustrate trends in health-related quality of life (HRQOL) reported by patients following prostate cancer treatment. Materials and Methods We designed and assessed the feasibility of integrating dashboards into care in 3 steps: (1) capture PRO needs of patients and providers through focus groups and interviews; (2) iteratively build and refine a prototype dashboard; and (3) pilot test dashboards with patients and their provider during follow-up care. Results Focus groups (n = 60 patients) prioritized needs for dashboards that compared longitudinal trends in patients’ HRQOL with “men like me.” Of the candidate dashboard designs, 50 patients and 50 providers rated pictographs less helpful than bar charts, line graphs, or tables (P < .001) and preferred bar charts and line graphs most. Given these needs and the design recommendations from our Patient Advisory Board (n = 7) and design experts (n = 7), we built and refined a prototype that charts patients’ HRQOL compared with age- and treatment-matched patients in personalized dashboards. Pilot testing dashboard use (n = 12 patients) improved compliance with quality indicators for prostate cancer care (P < .01). Conclusion PRO dashboards are a promising approach for integrating patient-generated data into prostate cancer care. Informed by human-centered design principles, this work establishes guidance on dashboard content, tailoring, and clinical use that patients and providers find meaningful. PMID:26260247

Airborne asbestos in public buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesson, J.; Hatfield, J.; Schultz, B.

The U.S. Environmental Protection Agency sampled air in 49 government-owned buildings (six buildings with no asbestos-containing material, six buildings with asbestos-containing material in generally good condition, and 37 buildings with damaged asbestos-containing material). This is the most comprehensive study to date of airborne asbestos levels in U.S. public buildings during normal building activities. The air outside each building was also sampled. Air samples were analyzed by transmission electron microscopy using a direct transfer preparation technique. The results show an increasing trend in average airborne asbestos levels; outdoor levels are lowest and levels in buildings with damaged asbestos-containing material are highest.more » However, the measured levels and the differences between indoors and outdoors and between building categories are small in absolute magnitude. Comparable studies from Canada and the UK, although differing in their estimated concentrations, also conclude that while airborne asbestos levels may be elevated in buildings that contain asbestos, levels are generally low. This conclusion does not eliminate the possibility of higher airborne asbestos levels during maintenance or renovation that disturbs the asbestos-containing material.« less

Measures to reduce construction time of high-rise buildings

NASA Astrophysics Data System (ADS)

Kolchedantsev, Leonid; Adamtsevich, Aleksey; Stupakova, Olga; Drozdov, Alexander

2018-03-01

The organizational and technological solutions for high-rise buildings construction efficiency increase are considered, primarily - decrease of typical floor construction time and improvement of bearing structures concrete quality. The essence of offered technology is: a concrete mixing station and a polygon mainly for load-bearing wall panels with starter bars casting are located on the building site; for reinforced concrete components manufacturing and butt joints grouting the warmed-up concrete mixtures are used. The results of researches and elaborations carried out by the SPSUACE in area of a preliminary warming-up of concrete mixtures are presented. The possibility and feasibility of their usage in high-rise buildings and of excess height buildings construction including cast-in-place and precast execution are shown. The essence of heat-vibro treating of concrete mixture is revealed as a kind of prior electroresistive curing, and the achieved results are: accelerated concrete strength gain, power inputs decrease, concrete quality improvement. It is shown that the location of a concrete mixing station on the building site enables to broaden possibilities of the "thermos" method use and to avoid concrete mixtures warming up in medium-mass structures erection (columns, girders) during the high-rise buildings construction. It is experimentally proved that the splice between precast elements encased with warmed-up concrete mixture is equal with conjugated elements in strength.

Application of soil block without burning process and calcium silicate panels as building wall in mountainous area

NASA Astrophysics Data System (ADS)

Noerwasito, Vincentius Totok; Nasution, Tanti Satriana Rosary

2017-11-01

Utilization of local building materials in a residential location in mountainous area is very important, considering local material as a low-energy building material because of low transport energy. The local building materials used in this study are walls made from soil blocks. The material was made by the surrounding community from compacted soil without burning process. To maximize the potential of soil block to the outdoor temperature in the mountains, it is necessary to add non-local building materials as an insulator from the influence of the outside air. The insulator was calcium silicate panel. The location of the research is Trawas sub-district, Mojokerto regency, which is a mountainous area. The research problem is on applying the composition of local materials and calcium silicate panels that it will be able to meet the requirements as a wall building material and finding to what extent the impact of the wall against indoor temperature. The result from this research was the application of soil block walls insulated by calcium silicate panels in a building model. Besides, because of the utilization of those materials, the building has a specific difference between indoor and outdoor temperature. Thus, this model can be applied in mountainous areas in Indonesia.

Functionalised Silk Fibres

DTIC Science & Technology

2012-07-30

rubber moulds (14 x 5 x 6 mm; RL060, ProSciTech, QLD), frozen at -20ºC overnight, and placed in a freeze - dryer (FD355DMP, FTS Systems) for 24 hours...surface area, low volume materials: electrospun fibres and freeze -dried sponges (Figure 9). Each new material type is described in detail below...surface area materials generated from recombinant honeybee silk proteins. (A) Electrospun fibres, scale bar is 200 nm. (B) Freeze dried sponges

Room temperature high power mid-IR diode laser bars for atmospheric sensing applications

NASA Astrophysics Data System (ADS)

Crump, Paul; Patterson, Steve; Dong, Weimin; Grimshaw, Mike; Wang, Jun; Zhang, Shiguo; Elim, Sandrio; Bougher, Mike; Patterson, Jason; Das, Suhit; Wise, Damian; Matson, Triston; Balsley, David; Bell, Jake; DeVito, Mark; Martinsen, Rob

2007-04-01

Peak CW optical power from single 1-cm diode laser bars is advancing rapidly across all commercial wavelengths and the available range of emission wavelengths also continues to increase. Both high efficiency ~ 50% and > 100-W power InP-based CW bars have been available in bar format around 1500-nm for some time, as required for eye-safe illuminators and for pumping Er-YAG crystals. There is increasing demand for sources at longer wavelengths. Specifically, 1900-nm sources can be used to pump Holmium doped YAG crystals, to produce 2100-nm emission. Emission near 2100-nm is attractive for free-space communications and range-finding applications as the atmosphere has little absorption at this wavelength. Diode lasers that emit at 2100-nm could eliminate the need for the use of a solid-state laser system, at significant cost savings. 2100-nm sources can also be used as pump sources for Thulium doped solid-state crystals to reach even longer wavelengths. In addition, there are several promising medical applications including dental applications such as bone ablation and medical procedures such as opthamology. These long wavelength sources are also key components in infra-red-counter-measure systems. We have extended our high performance 1500-nm material to longer wavelengths through optimization of design and epitaxial growth conditions and report peak CW output powers from single 1-cm diode laser bars of 37W at 1910-nm and 25W at 2070-nm. 1-cm bars with 20% fill factor were tested under step-stress conditions up to 110-A per bar without failure, confirming reasonable robustness of this technology. Stacks of such bars deliver high powers in a collimated beam suitable for pump applications. We demonstrate the natural spectral width of ~ 18nm of these laser bars can be reduced to < 3-nm with use of an external Volume Bragg Grating, as required for pump applications. We review the developments required to reach these powers, latest advances and prospects for longer wavelength, higher power and higher efficiency.

Using reclaimed lumber and wood flooring in construction : measuring environmental impact using life-cycle inventory analysis

Treesearch

Richard D. Bergman; Hongmei Gu; Robert H. Falk; Thomas R. Napier

2010-01-01

With green building concepts becoming widespread in the construction field, building practices and materials are being examined for their environmental impact. Reusing building materials has a distinct advantage over using newly manufactured materials because these reclaimed materials avoid greenhouse gas emissions associated with new (virgin) material manufacturing....

Physical cognition: birds learn the structural efficacy of nest material

PubMed Central

Bailey, Ida E.; Morgan, Kate V.; Bertin, Marion; Meddle, Simone L.; Healy, Susan D.

2014-01-01

It is generally assumed that birds’ choice of structurally suitable materials for nest building is genetically predetermined. Here, we tested that assumption by investigating whether experience affected male zebra finches’ (Taeniopygia guttata) choice of nest material. After a short period of building with relatively flexible string, birds preferred to build with stiffer string while those that had experienced a stiffer string were indifferent to string type. After building a complete nest with either string type, however, all birds increased their preference for stiff string. The stiffer string appeared to be the more effective building material as birds required fewer pieces of stiffer than flexible string to build a roofed nest. For birds that raised chicks successfully, there was no association between the material they used to build their nest and the type they subsequently preferred. Birds’ material preference reflected neither the preference of their father nor of their siblings but juvenile experience of either string type increased their preference for stiffer string. Our results represent two important advances: (i) birds choose nest material based on the structural properties of the material; (ii) nest material preference is not entirely genetically predetermined as both the type and amount of experience influences birds’ choices. PMID:24741011

Physical cognition: birds learn the structural efficacy of nest material.

PubMed

Bailey, Ida E; Morgan, Kate V; Bertin, Marion; Meddle, Simone L; Healy, Susan D

2014-06-07

It is generally assumed that birds' choice of structurally suitable materials for nest building is genetically predetermined. Here, we tested that assumption by investigating whether experience affected male zebra finches' (Taeniopygia guttata) choice of nest material. After a short period of building with relatively flexible string, birds preferred to build with stiffer string while those that had experienced a stiffer string were indifferent to string type. After building a complete nest with either string type, however, all birds increased their preference for stiff string. The stiffer string appeared to be the more effective building material as birds required fewer pieces of stiffer than flexible string to build a roofed nest. For birds that raised chicks successfully, there was no association between the material they used to build their nest and the type they subsequently preferred. Birds' material preference reflected neither the preference of their father nor of their siblings but juvenile experience of either string type increased their preference for stiffer string. Our results represent two important advances: (i) birds choose nest material based on the structural properties of the material; (ii) nest material preference is not entirely genetically predetermined as both the type and amount of experience influences birds' choices.

Fracture resistance of five pin-retained core build-up materials on teeth with and without extracoronal preparation.

PubMed

Burke, F J; Shaglouf, A G; Combe, E C; Wilson, N H

2000-01-01

Core build-ups should provide satisfactory strength and resistance to fracture both before and after crown preparation. This paper examines the resistance to fracture of core build-ups in different materials and the fracture resistance of core build-ups when these have been reduced for full crown preparation. Standardized core build-ups were made on groups of extracted molar teeth of similar size, with 10 teeth per group. Three resin-composite (prisma APH: Dentsply, Weybridge, UK; Ti-Core, Essential Dental Systems, NJ, US and Coradent, Vivadent, Liechtenstein), one cermet (Ketac-Silver, ESPE GmbH, Seefeld, Germany) and one amalgam material (Duralloy, Degussa Ltd, Cheshire, UK). These specimens were subjected to compressive force on a universal testing machine and the force at fracture noted. Standardized full crown preparations were made on a further five groups of core build-up specimens using the same materials as above. These prepared specimens were subjected to compressive force on a universal testing machine and the force to fracture noted. The results indicated that amalgam core build-ups demonstrated higher fracture resistance than the other materials examined. There was a general decrease in the fracture strength of the specimens following crown preparation, with the teeth restored with the amalgam core build-ups showing a greater percentage reduction in fracture strength than the other materials tested. Prepared core build-ups in a hybrid composite material provided the highest fracture resistance. The cermet material used provided the lowest resistance to fracture in both the core build-up and crown preparation specimens. In terms of fracture resistance, no advantage was apparent in using the two composite materials designated as being specifically appropriate for core build-ups.

Effect of sonication treatment on fibrilating snake fruit (Sallaca) frond fiber

NASA Astrophysics Data System (ADS)

Darmanto, Seno; Rochardjo, Heru S. B.; Jamasri, Widyorini, Ragil

2018-02-01

Aim of this research is to investigate influence of chemical and sonication treatment on fibrillating and mechanical properties of snake fruit frond fiber. The presence of surface impurities and the large amount of hydroxyl groups in natural fibers make less attractive for polymeric materials reinforcement. Effort to remove the impurities can be done by few treatments that consist of physical, chemical and mechanical treatment. Snake fruit frond bundle fiber were firstly subjected to chemical treatments with alkali solution, steaming at 2 bar and steam explosion at 6 bar by 40 times releasing of steam. Advanced treatment is done by flowing ultrasonic wave at 20 kHz by 90 - 210 watt. The output of fibrillation can reach fiber in range 10 - 25 nm compared with 10.72 µm in diameter for sonication and 6 bar in pressure of steam with 40x of rapidly steam release respectively.

Microstructural Changes Due to Alkali-Silica Reaction during Standard Mortar Test

PubMed Central

Shin, Jun-Ho; Struble, Leslie J.; Kirkpatrick, R. James

2015-01-01

The microstructural development of mortar bars with silica glass aggregate undergoing alkali-silica reaction (ASR) under the conditions of American Society for Testing and Materials (ASTM) Standard Test C1260 was analyzed using scanning electron microscopy and qualitative X-ray microanalysis. Cracking in the aggregate, the hydrated paste, and the paste-aggregate interface was important in the development of the microstructure. Cracks were characterized according to their location, their relationship to other cracks, and whether they are filled with ASR gel. Expansion of the bars was approximately 1% at 12 days and 2% at 53 days. They fell apart by 63 days. The bars contained two zones, an inner region that was undergoing ASR and an outer and much more highly damaged zone that extended further inward over time. Evidence of ASR was present even during the period when specimens were immersed in water, prior to immersion in NaOH solution. PMID:28793711

Microstructural Changes Due to Alkali-Silica Reaction during Standard Mortar Test.

PubMed

Shin, Jun-Ho; Struble, Leslie J; Kirkpatrick, R James

2015-12-02

The microstructural development of mortar bars with silica glass aggregate undergoing alkali-silica reaction (ASR) under the conditions of American Society for Testing and Materials (ASTM) Standard Test C1260 was analyzed using scanning electron microscopy and qualitative X-ray microanalysis. Cracking in the aggregate, the hydrated paste, and the paste-aggregate interface was important in the development of the microstructure. Cracks were characterized according to their location, their relationship to other cracks, and whether they are filled with ASR gel. Expansion of the bars was approximately 1% at 12 days and 2% at 53 days. They fell apart by 63 days. The bars contained two zones, an inner region that was undergoing ASR and an outer and much more highly damaged zone that extended further inward over time. Evidence of ASR was present even during the period when specimens were immersed in water, prior to immersion in NaOH solution.

[Modelling metallic bars in an orthopaedic laboratory: postural and biomechanical analysis].

PubMed

Draicchio, F; Miccio, A; Mari, S; Silvetti, A; Forzano, F; Ranavolo, A

2012-01-01

Aim of this work is to assess, with an objective technique (i.e. surface electromyography), the upper limb biomechanical load in workers specialized in manufacturing of orthopedic prostheses. We considered two different working configurations (workstation height at 105 and 110 cm) and three different materials to be modeled (aluminum, steel and titanium). Our results showed significant differences between aluminum/steel and titanium bars. As regards the working configurations, we found differences in the muscle activation patterns between the two heights, with an increased exertion of the shoulder muscles at 110 cm with respect to 105.

Failure Waves in Cylindrical Glass Bars

NASA Astrophysics Data System (ADS)

Cazamias, James U.; Bless, Stephan J.; Marder, Michael P.

1997-07-01

Failure waves, a propagating front separating virgin and comminuted material, have been receiving a fair amount of attention the last couple of years. While most scientists have been looking at failure waves in plate impact geometries, we have conducted a series of experiments on Pyrex bars. In this paper, we present two types of photographic data from a series of tests. A streak camera was used to determine velocities of the failure front as a function of impact stress. A polaroid camera and a flash lamp provide detailed pictures of the actual event. Attempts were made to observe failure waves in amorphous quartz and acrylic.

House moves to block Internet censorship.

PubMed

Mirken, B

1995-08-18

Congress has created conflicting amendments to the Communications Decency Act, an amendment to the telecommunications deregulation bill. The Senate amendment contains sweeping language barring objectionable communications online. Observers fear this will block online distribution of AIDS prevention information as well as bar responses by activist's of drug companies and government officials. The House amendments seek to protect online services from liability if they restrict access to objectionable materials, while another amendment seeks to modify obscenity laws to criminalize only some forms of online speech. These conflicts are to be resolved in a House-Senate conference committee whose meeting date is yet to be decided.

Designing tri-branched multiple-site SO2 capture materials.

PubMed

Li, Chenchen; Lu, Dongmei; Wu, Chao

2018-06-07

SO2 capture materials usually have multiple reactive sites located within a limited space, thus absorptions (or adsorptions) of disparate strengths and low effective capacity per sorption-desorption cycle become the natural results of the so-called "coverage effects" (due to both the electronic and steric effects). Here, we propose a tri-branched framework with separated reactive sites and nearly uniform charge distribution on the reacting atoms. Through density functional theory (DFT)-based calculations and simulated isotherms, two N-centered anionic structures (terminated with amine (TAEA) and imidazolyl (TIA) groups, respectively) are selected from a series of representative tri-branched species. The TAEA-based ILs are predicted to exhibit the highest uptakes (about 6.1 mol SO2 per mole IL) at 1 bar of SO2 and 20 °C, which reach the ceiling capacity that a negative charge can provide. The TIA-based ILs have small differences in their SO2 sequential binding energies and they are estimated to have the best effective SO2 capacity during a sorption-desorption cycle (about 2.6 mol SO2 per mole IL, absorption at 1 bar of SO2 and 20 °C and desorption at 1 bar of SO2 and 120 °C). Moreover, we also find that the designed species can efficiently capture other gases like NO.

A multi-segment soft actuator for biomedical applications based on IPMCs

NASA Astrophysics Data System (ADS)

Zhao, Dongxu; Wang, Yanjie; Liu, Jiayu; Luo, Meng; Li, Dichen; Chen, Hualing

2015-04-01

With rapid progress of biomedical devices towards miniaturization, flexibility, multifunction and low cost, the restrictions of traditional mechanical structures become particularly apparent, while soft materials become research focus in broad fields. As one of the most attractive soft materials, Ionic Polymer-Metal Composite (IPMC) is widely used as artificial muscles and actuators, with the advantages of low driving-voltage, high efficiency of electromechanical transduction and functional stabilization. In this paper, a new intuitive control method was presented to achieve the omnidirectional bending movements and was applied on a representative actuation structure of a multi-degree-offreedom soft actuator composed of two segments bar-shaped IPMC with a square cross section. Firstly, the bar-shaped IPMCs were fabricated by the solution casting method, reducing plating, autocatalytic plating method and cut into shapes successively. The connectors of the multi-segment IPMC actuator were fabricated by 3D printing. Then, a new control method was introduced to realize the intuitive mapping relationship between the actuator and the joystick manipulator. The control circuit was designed and tested. Finally, the multi-degree-of-freedom actuator of 2 segments bar-shaped IPMCs was implemented and omnidirectional bending movements were achieved, which could be a promising actuator for biomedical applications, such as endoscope, catheterism, laparoscopy and the surgical resection of tumors.

Modeling the effect of heatsink performance in high-peak-power laser-diode-bar pump sources for solid-state lasers 011 011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Honea, E.C., LLNL

We derive approximate expressions for transient output power and wavelength chirp of high- peak-power laser-diode bars assuming one-dimensional heat flow and linear temperature dependences for chirp and efficiency. The model is derived for pulse durations, 10 < {tau} < 1000 ps, typically used for diode-pumped solid-state lasers and is in good agreement with experimental data for Si heatsink mounted 940 nm laser-diode bars operating at 100 W/cm. The analytic expressions are more flexible and easily used than the results of operating point dependent numerical modeling. In addition, the analytic expressions used here can be integrated to describe the energy permore » unit wavelength for a given pulse duration, initial emission bandwidth and heatsink material. We find that the figure-of-merit for a heatsink material in this application is ({rho}C{sub p}K) where {rho}C{sub p} is the volumetric heat capacity and K is the thermal conductivity. As an example of the utility of the derived expressions, we determine an effective absorption coefficient as a function of pump pulse duration for a diode-pumped solid-state laser utilizing Yb:Sr{sub 5}(PO{sub 4}){sub 3}F (Yb:S-FAP) as the gain medium.« less

Hydrothermal carbonization of rice husk for fuel upgrading

NASA Astrophysics Data System (ADS)

Suteerawattananonda, N.; Kongkaew, N.; Patumsawad, S.

2018-01-01

The biomass is popularly used as renewable energy. In Thailand rice is the most consume agricultural products. Agricultural residues from rice husk can be an energy resource. However, alkali and alkali earth materials (AAEMs) in biomass ash are the causes of corrosion and erosion problem in the heat exchanger equipment, while the acidity of ash affects the slagging agglomeration problem. Reduction of alkali and alkali earth materials can minimize the problem. In order to challenge the reduction of alkali and alkali earth materials in biomass ash, hydrothermal carbonization process was selected. Thai rice husk was used as sample to compare the result of treatment. The rice husk was heated under the condition of different temperature ranged from 180°C to 250°C, at operate pressure ranges from 12 bar to 42 bar with residence holding reaction time 1 hour. The results of proximate analysis show that the percentage by mass of fixed carbon are increased 2 times, but volatile matter is decreased by 40% and ash content is decreased by 11% due to the increment of temperature. Meanwhile, the X-Ray fluorescence (XRF) analysis results show the decreasing of alkali and alkali earth materials are reduced.

Particulate Titanium Matrix Composites Tested-Show Promise for Space Propulsion Applications

NASA Technical Reports Server (NTRS)

Thesken, John C.; Lerch, Bradley A.; Arnold, Steven M.

2003-01-01

New manufacturing technologies can now produce uniformly distributed particle strengthened titanium matrix composites (TMCs) at lower cost than many types of continuous-fiber composites. The innovative process results in near-final-shape components having a material stiffness up to 26-percent greater than that of components made with conventional titanium materials. This benefit is achieved with no significant increase in the weight of the component. The improved mechanical performance and low-cost manufacturing capability motivated a review of particulate-reinforced metal composite technology as a way to lower the cost and weight of space-access propulsion systems. Focusing on the elevated-temperature properties of titanium alloy Ti-6Al-4V as the matrix material, researchers at the NASA Glenn Research Center conducted experiments to verify the improved performance of the alloy containing 10 wt% of ceramic titanium carbide (TiC) particles. The appropriate blend of metal and ceramic powder underwent a series of cold and hot isostatic pressing procedures to yield bar stock. A set of round dogbone specimens was manufactured from a small sample of the bars. The TMC material proved to have good machinability at this particle concentration as there was no difficulty in producing high-quality specimens.

Anisotropic Effects on Constitutive Model Parameters of Aluminum Alloys

NASA Astrophysics Data System (ADS)

Brar, Nachhatter; Joshi, Vasant

2011-06-01

Simulation of low velocity impact on structures or high velocity penetration in armor materials heavily rely on constitutive material models. The model constants are required input to computer codes (LS-DYNA, DYNA3D or SPH) to accurately simulate fragment impact on structural components made of high strength 7075-T651 aluminum alloys. Johnson-Cook model constants determined for Al7075-T651 alloy bar material failed to simulate correctly the penetration into 1' thick Al-7075-T651plates. When simulations go well beyond minor parameter tweaking and experimental results are drastically different it is important to determine constitutive parameters from the actual material used in impact/penetration experiments. To investigate anisotropic effects on the yield/flow stress of this alloy we performed quasi-static and high strain rate tensile tests on specimens fabricated in the longitudinal, transverse, and thickness directions of 1' thick Al7075-T651 plate. Flow stresses at a strain rate of ~1100/s in the longitudinal and transverse direction are similar around 670MPa and decreases to 620 MPa in the thickness direction. These data are lower than the flow stress of 760 MPa measured in Al7075-T651 bar stock.

Development of a Hopkinson Bar Apparatus for Testing Soft Materials: Application to a Closed-Cell Aluminum Foam.

PubMed

Peroni, Marco; Solomos, George; Babcsan, Norbert

2016-01-05

An increasing interest in lightweight metallic foams for automotive, aerospace, and other applications has been observed in recent years. This is mainly due to the weight reduction that can be achieved using foams and for their mechanical energy absorption and acoustic damping capabilities. An accurate knowledge of the mechanical behavior of these materials, especially under dynamic loadings, is thus necessary. Unfortunately, metal foams and in general "soft" materials exhibit a series of peculiarities that make difficult the adoption of standard testing techniques for their high strain-rate characterization. This paper presents an innovative apparatus, where high strain-rate tests of metal foams or other soft materials can be performed by exploiting the operating principle of the Hopkinson bar methods. Using the pre-stress method to generate directly a long compression pulse (compared with traditional SHPB), a displacement of about 20 mm can be applied to the specimen with a single propagating wave, suitable for evaluating the whole stress-strain curve of medium-sized cell foams (pores of about 1-2 mm). The potential of this testing rig is shown in the characterization of a closed-cell aluminum foam, where all the above features are amply demonstrated.

Ada Compiler Validation Summary Report: Certificate Number: 940325S1. 11352 DDC-I DACS Sun SPARC/Solaries to Pentium PM Bare Ada Cross Compiler System, Version 4.6.4 Sun SPARCclassic = Intel Pentium (Operated as Bare Machine) Based in Xpress Desktop (Intel Product Number: XBASE6E4F-B)

DTIC Science & Technology

1994-03-25

Technology Building 225, Room A266 Gait•--eburg, Maryland 20899 U.S.A. Ada Von Ogan~ztionAda Jointt Program Office De & Software David R . Basel...Standards and Technology Building 225, Room A266 Gaithersburg, Maryland 20899 U.S.A. azi Ada Joint Program office Directoz’,’Coputer & Softvare David R ...characters, a bar (" r ) is written in the 16th position and the rest of the characters ame not prined. "* The place of the definition, i.e.. a line

Effects of Cohesive Sediment on Estuarine Morphology in Laboratory Scale Experiments

NASA Astrophysics Data System (ADS)

Braat, L.; Leuven, J.; Lokhorst, I.; Kleinhans, M. G.

2017-12-01

Mud plays a major role in forming and filling of river estuaries. River estuaries are typically build of sand and flanked by mudflats, which affect channel-shoal dynamics on time scales of centuries to millennia. In our research we aim to study the effects of mud on the shape and evolution of estuaries and where the largest effects occur. Recently a 20 m by 3 m flume (the Metronome) was developed at Utrecht University for tidal experiments. Complete estuaries are simulated in the Metronome by driving tidal flow by periodically tilting of the flume to counteract scaling problems. To simulate the effects of cohesive mud we supply nutshell grains to the system together with the river discharge. Three scenarios were tested, one with only sand, one with a low supply concentration of nutshell and one with a high concentration (left to right in figure).Estuaries that developed from an initial convergent shape are self-formed through bank erosion, continuous channel-shoal migration and bar and mud flat sedimentation (figure shows development over 15000 tilting cycles). The cohesive sediment deposits occur mainly on bars, but also on the flanks of the estuary and in abandoned channels. Due to its different erosional and depositional characteristics, the nutshell increases the elevation of the bars, which reduces storage and ebb-dominance and causes reduction of bar mobility and short cuts. These results agree with numerical model results. The large-scale effect is less widening of the estuary in the presence of mud and a decrease in channel-shoal migration, suggesting that mud confines estuary width in a similar manner as river floodplains.

Dowel Bar Retrofit Mix Design and Specification

DOT National Transportation Integrated Search

2012-02-01

The focus of this project was on identifying critical properties that control longterm performance of repair concrete, especially rapidsetting : materials extended using pea gravel (maximum size aggregate 9.5 mm). : In the first phase of this proj...

Bridges Structural Health Monitoring and Deterioration Detection - Synthesis of Knowledge and Technology

DOT National Transportation Integrated Search

2010-12-01

Bridges are continuously subjected to destructive effects of material aging, widespread corrosion of steel : reinforcing bars in concrete structures, corrosion of steel structures and components, increasing traffic : volume and overloading, or simply...

Performance of Chevron-notch short bar specimen in determining the fracture toughness of silicon nitride and aluminum oxide

NASA Technical Reports Server (NTRS)

Munz, D.; Bubsey, R. T.; Shannon, J. L., Jr.

1980-01-01

Ease of preparation and testing are advantages unique to the chevron-notch specimen used for the determination of the plane strain fracture toughness of extremely brittle materials. During testing, a crack develops at the notch tip and extends stably as the load is increased. For a given specimen and notch configuration, maximum load always occurs at the same relative crack length independent of the material. Fracture toughness is determined from the maximum load with no need for crack length measurement. Chevron notch acuity is relatively unimportant since a crack is produced during specimen loading. In this paper, the authors use their previously determined stress intensity factor relationship for the chevron-notch short bar specimen to examine the performance of that specimen in determining the plane strain fracture toughness of silicon nitride and aluminum oxide.

Evaluation of in-situ deformation experiments of TRIP steel

NASA Astrophysics Data System (ADS)

Procházka, J.; Kučerová, L.; Bystrianský, M.

2017-02-01

The paper reports on the behaviour of low alloyed TRIP (transformation induced plasticity) steel with Niobium during tensile test. The structures were analysed using in-situ tensile testing coupled with electron backscattering diffraction (EBSD) analysis carried out in scanning electron microscope (SEM). Steel specimens were of same chemical composition; however three different annealing temperatures, 800 °C, 850 °C and 950 °C, were applied to the material during the heat treatment. The treatment consisted of annealing for 20 minutes in the furnace; cooling in salt bath after the heating and holding at 425 °C for 20 minutes for all the samples. Untreated bar was used as reference material. Flat samples for deformation stage were cut out of the heat-treated bars. In situ documentation of microstructure and crystallography development were carried out during the deformation experiments. High deformation lead to significant degradation of EBSD signal.

A storey of buildings and materials

NASA Astrophysics Data System (ADS)

2017-12-01

Throughout history, the development of new materials and technologies has enabled more functional and aesthetically pleasing buildings. With the advent of sustainable architecture, the role of materials science in building innovation is becoming more prominent than ever.

Smoke-free Policy and Alcohol Use among Undergraduate College Students

PubMed Central

Butler, Karen M.; Rayens, Mary Kay; Hahn, Ellen J.; Adkins, Sarah M.; Staten, Ruth R.

2012-01-01

Objectives The purpose of this study was to assess attitudes and behaviors related to smoke-free policy among undergraduate student alcohol drinkers on a campus in a community with smoke-free bars. Design and Sample This was a secondary data analysis of a study in which participants completed mailed surveys assessing demographic characteristics, attitudes and behaviors related to alcohol and tobacco use and smoke-free policy (n=337). Opinion and behavior items were summarized descriptively; associations were examined using Kruskal Wallis tests and chi-square tests of association. Logistic regression tested for predictors of importance of smoke-free policy. Results Respondents were predominantly female and Caucasian; mean age 20.3 years. One-fourth were current smokers. Seventy-nine percent said the community smoke-free law had no effect on frequency of visiting bars. Eighty-seven percent said smoke-free policy in campus buildings was ‘somewhat’ or ‘very important’. Predictors of perceived importance of smoke-free policy included gender and smoking status. Conclusions Most smokers in this sample did not experience a change in their motivation to quit smoking or in number of cigarettes smoked daily. Implementation of a community smoke-free law did not reduce the likelihood of visiting bars. Women and nonsmokers were more likely to rate smoke-free campus policy as very important. PMID:22512427

Opportunity at the Top: How America's Best Teachers Could Close the Gaps, Raise the Bar, and Keep Our Nation Great. Building an Opportunity Culture for America's Teachers. Executive Summary

ERIC Educational Resources Information Center

Hassel, Bryan C.; Hassel, Emily Ayscue

2010-01-01

Our nation is squandering one of its most important resources--our best teachers--and children are paying the price. Current policy initiatives overlook the most obvious, immediate source of improved teaching effectiveness: The great teachers we already have. The top 25 percent of U.S. teachers--more than 800,000 of them--already achieve results…

Stellar mass distribution of S4G disk galaxies and signatures of bar-induced secular evolution

NASA Astrophysics Data System (ADS)

Díaz-García, S.; Salo, H.; Laurikainen, E.

2016-12-01

Context. Models of galaxy formation in a cosmological framework need to be tested against observational constraints, such as the average stellar density profiles (and their dispersion) as a function of fundamental galaxy properties (e.g. the total stellar mass). Simulation models predict that the torques produced by stellar bars efficiently redistribute the stellar and gaseous material inside the disk, pushing it outwards or inwards depending on whether it is beyond or inside the bar corotation resonance radius. Bars themselves are expected to evolve, getting longer and narrower as they trap particles from the disk and slow down their rotation speed. Aims: We use 3.6 μm photometry from the Spitzer Survey of Stellar Structure in Galaxies (S4G) to trace the stellar distribution in nearby disk galaxies (z ≈ 0) with total stellar masses 108.5 ≲ M∗/M⊙ ≲ 1011 and mid-IR Hubble types - 3 ≤ T ≤ 10. We characterize the stellar density profiles (Σ∗), the stellar contribution to the rotation curves (V3.6 μm), and the m = 2 Fourier amplitudes (A2) as a function of M∗ and T. We also describe the typical shapes and strengths of stellar bars in the S4G sample and link their properties to the total stellar mass and morphology of their host galaxy. Methods: For 1154 S4G galaxies with disk inclinations lower than 65°, we perform a Fourier decomposition and rescale their images to a common frame determined by the size in physical units, by their disk scalelength, and for 748 barred galaxies by both the length and orientation of their bars. We stack the resized density profiles and images to obtain statistically representative average stellar disks and bars in bins of M∗ and T. Based on the radial force profiles of individual galaxies we calculate the mean stellar contribution to the circular velocity. We also calculate average A2 profiles, where the radius is normalized to R25.5. Furthermore, we infer the gravitational potentials from the synthetic bars to obtain the tangential-to-radial force ratio (QT) and A2 profiles in the different bins. We also apply ellipse fitting to quantitatively characterize the shape of the bar stacks. Results: For M∗ ≥ 109M⊙, we find a significant difference in the stellar density profiles of barred and non-barred systems: (I) disks in barred galaxies show larger scalelengths (hR) and fainter extrapolated central surface brightnesses (Σ°); (II) the mean surface brightness profiles (Σ∗) of barred and non-barred galaxies intersect each other slightly beyond the mean bar length, most likely at the bar corotation; and (III) the central mass concentration of barred galaxies is higher (by almost a factor 2 when T ≤ 5) than in their non-barred counterparts. The averaged Σ∗ profiles follow an exponential slope down to at least 10 M⊙ pc-2, which is the typical depth beyond which the sample coverage in the radial direction starts to drop. Central mass concentrations in massive systems (≥1010M⊙) are substantially larger than in fainter galaxies, and their prominence scales with T. This segregation also manifests in the inner slope of the mean stellar component of the circular velocity: lenticular (S0) galaxies present the most sharply rising V3.6 μm. Based on the analysis of bar stacks, we show that early- and intermediate-type spirals (0 ≤ T< 5) have intrinsically narrower bars than later types and S0s, whose bars are oval-shaped. We show a clear agreement between galaxy family and quantitative estimates of bar strength. In early- and intermediate-type spirals, A2 is larger within and beyond the typical bar region among barred galaxies than in the non-barred subsample. Strongly barred systems also tend to have larger A2 amplitudes at all radii than their weakly barred counterparts. Conclusions: Using near-IR wavelengths (S4G 3.6 μm), we provide observational constraints that galaxy formation models can be checked against. In particular, we calculate the mean stellar density profiles, and the disk(+bulge) component of the rotation curve (and their dispersion) in bins of M∗ and T. We find evidence for bar-induced secular evolution of disk galaxies in terms of disk spreading and enhanced central mass concentration. We also obtain average bars (2D), and we show that bars hosted by early-type galaxies are more centrally concentrated and have larger density amplitudes than their late-type counterparts. The FITS files of the synthetic images and the tabulated radial profiles of the mean (and dispersion of) stellar mass density, 3.6 μm surface brightness, Fourier amplitudes, gravitational force, and the stellar contribution to the circular velocity are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/596/A84

Chemical and Structural Stability of Lithium-Ion Battery Electrode Materials under Electron Beam

DOE PAGES

Lin, Feng; Markus, Isaac M.; Doeff, Marca M.; ...

2014-07-16

Our investigation of chemical and structural dynamics in battery materials is essential to elucidation of structure-property relationships for rational design of advanced battery materials. Spatially resolved techniques, such as scanning/transmission electron microscopy (S/TEM), are widely applied to address this challenge. But, battery materials are susceptible to electron beam damage, complicating the data interpretation. In this study, we demonstrate that, under electron beam irradiation, the surface and bulk of battery materials undergo chemical and structural evolution equivalent to that observed during charge-discharge cycling. In a lithiated NiO nanosheet, a Li2CO3-containing surface reaction layer (SRL) was gradually decomposed during electron energy loss spectroscopy (EELS) acquisition. For cycled LiNi 0.4Mn 0.4Co 0.18Ti 0.02O 2 particles, repeated electron beam irradiation induced a phase transition from an Rmore » $$\\bar{3}$$m layered structure to an rock-salt structure, which is attributed to the stoichiometric lithium and oxygen removal from R$$\\bar{3}$$m 3a and 6c sites, respectively. Nevertheless, it is still feasible to preserve pristine chemical environments by minimizing electron beam damage, for example, in using fast electron imaging and spectroscopy. Finally, the present study provides examples of electron beam damage on lithium-ion battery materials and suggests that special attention is necessary to prevent misinterpretation of experimental results.« less

The Nonlinear Evolution of Massive Stellar Core Collapses That ``Fizzle''

NASA Astrophysics Data System (ADS)

Imamura, James N.; Pickett, Brian K.; Durisen, Richard H.

2003-04-01

Core collapse in a massive rotating star may pause before nuclear density is reached, if the core contains total angular momentum J>~1049 g cm2 s-1. In such aborted or ``fizzled'' collapses, temporary equilibrium objects form that, although rapidly rotating, are secularly and dynamically stable because of the high electron fraction per baryon Ye>0.3 and the high entropy per baryon Sb/k~1-2 of the core material at neutrino trapping. These fizzled collapses are called ``fizzlers.'' In the absence of prolonged infall from the surrounding star, the evolution of fizzlers is driven by deleptonization, which causes them to contract and spin up until they either become stable neutron stars or reach the dynamic instability point for barlike modes. The barlike instability case is of current interest because the bars would be sources of gravitational wave (GW) radiation. In this paper, we use linear and nonlinear techniques, including three-dimensional hydrodynamic simulations, to study the behavior of fizzlers that have deleptonized to the point of reaching dynamic bar instability. The simulations show that the GW emission produced by bar-unstable fizzlers has rms strain amplitude r15h=10-23 to 10-22 for an observer on the rotation axis, with wave frequency of roughly 60-600 Hz. Here h is the strain and r15= (r/15 Mpc) is the distance to the fizzler in units of 15 Mpc. If the bars that form by dynamic instability can maintain GW emission at this level for 100 periods or more, they may be detectable by the Laser Interferometer Gravitational-Wave Observatory at the distance of the Virgo Cluster. They would be detectable as burst sources, defined as sources that persist for ~10 cycles or less, if they occurred in the Local Group of galaxies. The long-term behavior of the bars is the crucial issue for the detection of fizzler events. The bars present at the end of our simulations are dynamically stable but will evolve on longer timescales because of a variety of effects, such as shock heating, infall, deleptonization, and cooling, as well as gravitational radiation and Newtonian gravitational coupling to surrounding material. Long-term simulations including these effects will be necessary to determine the ultimate fate and GW production of fizzlers with certainty.

Environmental Evaluation of Building Materials of 5 Slovak Buildings

NASA Astrophysics Data System (ADS)

Porhincak, Milan; Estokova, Adriana

2013-11-01

Building activity has recently led to the deterioration of environment and has become unsustainable. Several strategies have been introduced in order to minimize consumption of energy and resulting CO2 emissions having their origin in the operational phase. But also other stages of Life Cycle should are important to identify the overall environmental impact of construction sector. In this paper 5 similar Slovak buildings (family houses) were analyzed in terms of environmental performance of building materials used for their structures. Evaluation included the weight of used materials, embodied energy and embodied CO2 and SO2 emissions. Analysis has proven that the selection of building materials is an important factor which influences the environmental profile. Findings of the case study indicated that materials like concrete, ceramic or thermal insulation materials based on polystyrene and mineral wool are ones with the most negative environmental impact.

The use of portable equipment for the activity concentration index determination of building materials: method validation and survey of building materials on the Belgian market.

PubMed

Stals, M; Verhoeven, S; Bruggeman, M; Pellens, V; Schroeyers, W; Schreurs, S

2014-01-01

The Euratom BSS requires that in the near future (2015) the building materials for application in dwellings or buildings such as offices or workshops are screened for NORM nuclides. The screening tool is the activity concentration index (ACI). Therefore it is expected that a large number of building materials will be screened for NORM and thus require ACI determination. Nowadays, the proposed standard for determination of building material ACI is a laboratory analyses technique with high purity germanium spectrometry and 21 days equilibrium delay. In this paper, the B-NORM method for determination of building material ACI is assessed as a faster method that can be performed on-site, alternative to the aforementioned standard method. The B-NORM method utilizes a LaBr3(Ce) scintillation probe to obtain the spectral data. Commercially available software was applied to comprehensively take into account the factors determining the counting efficiency. The ACI was determined by interpreting the gamma spectrum from (226)Ra and its progeny; (232)Th progeny and (40)K. In order to assess the accuracy of the B-NORM method, a large selection of samples was analyzed by a certified laboratory and the results were compared with the B-NORM results. The results obtained with the B-NORM method were in good correlation with the results obtained by the certified laboratory, indicating that the B-NORM method is an appropriate screening method to assess building material ACI. The B-NORM method was applied to analyze more than 120 building materials on the Belgian market. No building materials that exceed the proposed reference level of 1 mSv/year were encountered. Copyright © 2013 Elsevier Ltd. All rights reserved.

Wood as a sustainable building material

Treesearch

Robert H. Falk

2009-01-01

Few building materials possess the environmental benefits of wood. It is not only the most widely used building material in the United States but also one with characteristics that make it suitable for a wide range of applications. Efficient, durable, and useful wood products produced from trees range from a minimally processed log at a log-home building site to a...

Flammability tests for regulation of building and construction materials

Treesearch

K. Sumathipala

2006-01-01

The regulation of building materials and products for flammability is critical to ensure the safety of occupants in buildings and other structures. The involvement of exposed building materials and products in fires resulting in the loss of human life often spurs an increase in regulation and new test methods to address the problem. Flammability tests range from those...

Mechanical Behavior of a Low-Cost Ti-6Al-4V Alloy

NASA Astrophysics Data System (ADS)

Casem, D. T.; Weerasooriya, T.; Walter, T. R.

2018-01-01

Mechanical compression tests were performed on an economical Ti-6Al-4V alloy over a range of strain-rates and temperatures. Low rate experiments (0.001-0.1/s) were performed with a servo-hydraulic load frame and high rate experiments (1000-80,000/s) were performed with the Kolsky bar (Split Hopkinson pressure bar). Emphasis is placed on the large strain, high-rate, and high temperature behavior of the material in an effort to develop a predictive capability for adiabatic shear bands. Quasi-isothermal experiments were performed with the Kolsky bar to determine the large strain response at elevated rates, and bars with small diameters (1.59 mm and 794 µm, instrumented optically) were used to study the response at the higher strain-rates. Experiments were also conducted at temperatures ranging from 81 to 673 K. Two constitutive models are used to represent the data. The first is the Zerilli-Armstrong recovery strain model and the second is a modified Johnson-Cook model which uses the recovery strain term from the Zerilli-Armstrong model. In both cases, the recovery strain feature is critical for capturing the instability that precedes localization.

Unified model for the electromechanical coupling factor of orthorhombic piezoelectric rectangular bar with arbitrary aspect ratio

NASA Astrophysics Data System (ADS)

Rouffaud, R.; Levassort, F.; Hladky-Hennion, A.-C.

2017-02-01

Piezoelectric Single Crystals (PSC) are increasingly used in the manufacture of ultrasonic transducers and in particular for linear arrays or single element transducers. Among these PSCs, according to their microstructure and poled direction, some exhibit a mm2 symmetry. The analytical expression of the electromechanical coupling coefficient for a vibration mode along the poling direction for piezoelectric rectangular bar resonator is established. It is based on the mode coupling theory and fundamental energy ratio definition of electromechanical coupling coefficients. This unified formula for mm2 symmetry class material is obtained as a function of an aspect ratio (G) where the two extreme cases correspond to a thin plate (with a vibration mode characterized by the thickness coupling factor, kt) and a thin bar (characterized by k33'). To optimize the k33' value related to the thin bar design, a rotation of the crystallogaphic axis in the plane orthogonal to the poling direction is done to choose the highest value for PIN-PMN-PT single crystal. Finally, finite element calculations are performed to deduce resonance frequencies and coupling coefficients in a large range of G value to confirm developed analytical relations.

Stream and floodplain restoration in a riparian ecosystem disturbed by placer mining

USGS Publications Warehouse

Karle, Kenneth F.; Densmore, Roseann V.

1994-01-01

Techniques for the hydrologic restoration of placer-mined streams and floodplains were developed in Denali National Park and Preserve Alaska, USA. The hydrologic study focused on a design of stream and floodplain geometry using hydraulic capacity and shear stress equations. Slope and sinuosity values were based on regional relationships. Design requirements include a channel capacity for a 1.5-year (bankfull) discharge and a floodplain capacity for a 1.5- to 100-year discharge. Concern for potential damage to the project from annual flooding before natural revegetation occurs led to development of alder (Alnus crispa) brush bars to dissipate floodwater energy and encourage sediment deposition. The brush bars, constructed of alder bundles tied together and anchored laterally adjacent to the channel, were installed on the floodplain in several configurations to test their effectiveness. A moderate flood near the end of the two-year construction phase of the project provided data on channel design, stability, floodplain erosion, and brush bar effectiveness. The brush bars provided substantial protection, but unconsolidated bank material and a lack of bed armour for a new channel segment led to some bank erosion, slope changes and an increase in sinuosity in several reaches of the study area.

Algae and their biodegradation effects on building materials in the Ostrava industrial agglomeration

NASA Astrophysics Data System (ADS)

Vojtková, H.

2017-10-01

Microorganisms cause changes in the building stone, which reduce its usable life and reliability. Microalgae make important parts of the biodegradation consortia of microorganisms on the surface of building materials. Via their metabolites, microalgae affect the stability of mineral components and thus lead to the material destruction. The aim of the paper was to identify aerophytic microalgae on the surface of engineering structures in the Ostrava agglomeration, and to describe the basic interactions between such microorganisms and the building materials, which may lead to the destruction of the materials.

Seismic retrofit of spliced sleeve connections for precast bridge piers : research brief.

DOT National Transportation Integrated Search

2017-03-01

The rehabilitation method described in this paper concerns connections between precast columns and footings, and precast columns and pier caps. This research uses high-performance materials, including headed reinforcing bar, epoxy, nonshrink or expan...

Thallous halide materials for use in cryogenic applications

NASA Technical Reports Server (NTRS)

Lawless, William N. (Inventor)

1981-01-01

Thallous halides, either alone or in combination with other ceramic materials, are used in cryogenic applications such as heat exchange material for the regenerator section of a closed-cycle cryogenic refrigeration section, as stabilizing coatings for superconducting wires, and as dielectric insulating materials. The thallous halides possess unusually large specific heats at low temperatures, have large thermal conductivities, are nonmagnetic, and are nonconductors of electricity. They can be formed into a variety of shapes such as spheres, bars, rods, or the like and can be coated onto substrates.

Solvent mediated hybrid 2D materials: black phosphorus - graphene heterostructured building blocks assembled for sodium ion batteries.

PubMed

Li, Mengya; Muralidharan, Nitin; Moyer, Kathleen; Pint, Cary L

2018-06-07

Here we demonstrate the broad capability to exploit interactions at different length scales in 2D materials to prepare macroscopic functional materials containing hybrid black phosphorus/graphene (BP/G) heterostructured building blocks. First, heterostructured 2D building blocks are self-assembled during co-exfoliation in the solution phase based on electrostatic attraction of different 2D materials. Second, electrophoretic deposition is used as a tool to assemble these building blocks into macroscopic films containing these self-assembled 2D heterostructures. Characterization of deposits formed using this technique elucidates the presence of stacked and sandwiched 2D heterostructures, and zeta potential measurements confirm the mechanistic interactions driving this assembly. Building on the exceptional sodium alloying capacity of BP, these materials were demonstrated as superior binder-free and additive-free anodes for sodium batteries with specific discharge capacity of 2365 mA h gP-1 and long stable cycling duration. This study demonstrates how controllable co-processing of 2D materials can enable material control for stacking and building block assembly relevant to broad future applications of 2D materials.

Restored river corridors: first results on the effects of flow variability on vegetation cuttings survival rate and related root architecture

NASA Astrophysics Data System (ADS)

Pasquale, N.; Perona, P.; Jiang, Z.; Burlando, P.

2009-04-01

Understanding and predicting the evolution of river alluvial bed forms toward a vegetated or a non-vegetated morphology have important implications for restored river corridors and the related ecosystem functioning (see also Schäppi et al, this session). Vegetation recruitment and growth on non-cohesive material of river corridors, such as gravel bars and islands of braided river, depend on the ability of roots to develop and anchor efficiently such to resist against flow erosion. In this work, we study the interannual morphological evolution of a gravel bar island, the survival rate and the growth of a number of plots with different density and orientation of transplanted cuttings (Salix Alba), the space and time dynamics of which depend on erosion and deposition processes due to floods. Our purpose is to identify island locations where the hydrodynamic conditions are more suitable for plants germination, growth and survival in relation to the river hydrograph statistics. This information is a first step to build a stochastic model able to predict the future evolution and progress of the restoration action of the investigated river reach. We focus at the main island of River Thur at Niederneunforn (Canton Thurgau, Switzerland), the restoration success of which is investigated from a mechanistic viewpoint in the research project "REstored CORridor Dynamics" (www.record.ethz.ch). Accordingly, we analyze two recent Digital Elevation Models (1 year difference), which were first corrected to account for the river bathymetry, and then we compare them in order to extract relevant interannual morphological changes. Using a two dimensional numerical hydrodynamic model we simulate several flow conditions ranging from the minimum recorded flow up to the one that completely inundates the island. Hence, we build inundation maps of the island that we associate to the frequency and the submergence duration of every area. We then correlate such results to the observed survival rate and the root characteristics of a sample of 1-year old transplanted cuttings. Despite limited in number, the investigated sample suggests that roots are shot from different points of the cuttings, which seem to reflect their location on the island and the direction of major resistance to flow erosion, also in agreement with the inundation maps.

Learning about Science Graphs and Word Games. Superific Science Book V. A Good Apple Science Activity Book for Grades 5-8+.

ERIC Educational Resources Information Center

Conway, Lorraine

This packet of student materials contains a variety of worksheet activities dealing with science graphs and science word games. These reproducible materials deal with: (1) bar graphs; (2) line graphs; (3) circle graphs; (4) pictographs; (5) histograms; (6) artgraphs; (7) designing your own graphs; (8) medical prefixes; (9) color prefixes; (10)…

Cathode for a hall-heroult type electrolytic cell for producing aluminum

DOEpatents

Brown, Craig W.

2004-04-13

A method of producing aluminum from alumina in an electrolytic cell including using a cathode comprised of a base material having low electrical conductivity and wettable with molten aluminum to form a reaction layer having a high electrical conductivity on said base layer and a cathode bar extending from said reaction layer through said base material to conduct electrical current from said reaction layer.

Beneficial Uses of Dredged Material: Proceedings of the North Atlantic Regional Conference Held in Baltimore, Maryland on 12-14 May 1987.

DTIC Science & Technology

1988-01-01

wide through an offshore sand bar averaging about 16 feet in depth. The channel was sufficiently deepened by 1907 to permit the LUSITANIA to pass...This material was deposited in Disposal Area No. 1. The four drying basins and the settling basin were lined with 36-mil -Hy.palon liner to allow for

Advanced structural analysis of nanoporous materials by thermal response measurements.

PubMed

Oschatz, Martin; Leistner, Matthias; Nickel, Winfried; Kaskel, Stefan

2015-04-07

Thermal response measurements based on optical adsorption calorimetry are presented as a versatile tool for the time-saving and profound characterization of the pore structure of porous carbon-based materials. This technique measures the time-resolved temperature change of an adsorbent during adsorption of a test gas. Six carbide and carbon materials with well-defined nanopore architecture including micro- and/or mesopores are characterized by thermal response measurements based on n-butane and carbon dioxide as the test gases. With this tool, the pore systems of the model materials can be clearly distinguished and accurately analyzed. The obtained calorimetric data are correlated with the adsorption/desorption isotherms of the materials. The pore structures can be estimated from a single experiment due to different adsorption enthalpies/temperature increases in micro- and mesopores. Adsorption/desorption cycling of n-butane at 298 K/1 bar with increasing desorption time allows to determine the pore structure of the materials in more detail due to different equilibration times. Adsorption of the organic test gas at selected relative pressures reveals specific contributions of particular pore systems to the increase of the temperature of the samples and different adsorption mechanisms. The use of carbon dioxide as the test gas at 298 K/1 bar provides detailed insights into the ultramicropore structure of the materials because under these conditions the adsorption of this test gas is very sensitive to the presence of pores smaller than 0.7 nm.

Influence of different surface treatments on bond strength of novel CAD/CAM restorative materials to resin cement.

PubMed

Kömürcüoğlu, Meltem Bektaş; Sağırkaya, Elçin; Tulga, Ayça

2017-12-01

To evaluate the effects of different surface treatments on the bond strength of novel CAD/CAM restorative materials to resin cement by four point bending test. The CAD/CAM materials under investigation were e.max CAD, Mark II, Lava Ultimate, and Enamic. A total of 400 bar specimens (4×1.2×12 mm) (n=10) milled from the CAD/CAM blocks underwent various pretreatments (no pretreatment (C), hydrofluoric acid (A), hydrofluoric acid + universal adhesive (Scotchbond) (AS), sandblasting (Sb), and sandblasting + universal adhesive (SbS)). The bars were luted end-to-end on the prepared surfaces with a dual curing adhesive resin cement (Variolink N, Ivoclar Vivadent) on the custom-made stainless steel mold. Ten test specimens for each treatment and material combination were performed with four point bending test method. Data were analyzed using ANOVA and Tukey's test. The surface treatment and type of CAD/CAM restorative material showed a significant effect on the four point bending strength (FPBS) ( P <.001). For LDC, AS surface treatment showed the highest FPBS results (100.31 ± 10.7 MPa) and the lowest values were obtained in RNC (23.63 ± 9.0 MPa) for control group. SEM analyses showed that the surface topography of CAD/CAM restorative materials was modified after treatments. The surface treatment of sandblasting or HF acid etching in combination with a universal adhesive containing MDP can be suggested for the adhesive cementation of the novel CAD/CAM restorative materials.

MATERIALS TESTING REACTOR (MTR) BUILDING, TRA603. CONTEXTUAL VIEW OF MTR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MATERIALS TESTING REACTOR (MTR) BUILDING, TRA-603. CONTEXTUAL VIEW OF MTR BUILDING SHOWING NORTH SIDES OF THE HIGH-BAY REACTOR BUILDING, ITS SECOND/THIRD FLOOR BALCONY LEVEL, AND THE ATTACHED ONE-STORY OFFICE/LABORATORY BUILDING, TRA-604. CAMERA FACING SOUTHEAST. VERTICAL CONCRETE-SHROUDED BEAMS SUPPORT PRECAST CONCRETE PANELS. CONCRETE PROJECTION FORMED AS A BUNKER AT LEFT OF VIEW IS TRA-657, PLUG STORAGE BUILDING. INL NEGATIVE NO. HD46-42-1. Mike Crane, Photographer, 4/2005 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Measurement of natural radioactivity in building materials of Namakkal, Tamil Nadu, India using gamma-ray spectrometry.

PubMed

Ravisankar, R; Vanasundari, K; Chandrasekaran, A; Rajalakshmi, A; Suganya, M; Vijayagopal, P; Meenakshisundaram, V

2012-04-01

The natural level of radioactivity in building materials is one of the major causes of external exposure to γ-rays. The primordial radionuclides in building materials are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the radioactivity level in building materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the specific activity concentration of (226)Ra, (232)Th and (40)K in commonly used building materials from Namakkal, Tamil Nadu, India, using gamma-ray spectrometer. The radiation hazard due to the total natural radioactivity in the studied building materials was estimated by different approaches. The concentrations of the natural radionuclides and the radium equivalent activity in studied samples were compared with the corresponding results of different countries. From the analysis, it is found that these materials may be safely used as construction materials and do not pose significant radiation hazards. Copyright © 2011 Elsevier Ltd. All rights reserved.

Wood: a construction material for tall buildings

NASA Astrophysics Data System (ADS)

Wimmers, Guido

2017-12-01

Wood has great potential as a building material, because it is strong and lightweight, environmentally friendly and can be used in prefabricated buildings. However, only changes in building codes will make wood competitive with steel and concrete.

Non-motorized winter recreation impacts to snowmelt erosion, Tronsen Basin, Eastern Cascades, Washington.

PubMed

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm(2) total erosion occurring on the trail transects and -3.8 ± 2.4 cm(2) total erosion occurring on the control transect (P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm(2) (P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail (R (2) = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Non-motorized Winter Recreation Impacts to Snowmelt Erosion, Tronsen Basin, Eastern Cascades, Washington

NASA Astrophysics Data System (ADS)

Eagleston, Holly; Rubin, Charles

2013-01-01

Many recreation impact studies have focused on summer activities, but the environmental impact of winter recreation is poorly characterized. This study characterizes the impact of snowshoe/cross-country ski compaction and snowmelt erosion on trails. Trail cross-sectional profiles were measured before and after the winter season to map changes in erosion due to winter recreation. Compacted snow on the trail was 30 % more dense than snowpack off the trail before spring melt out. Snow stayed on the trail 7 days longer. Soil and organic material was transported after spring snowmelt with -9.5 ± 2.4 cm2 total erosion occurring on the trail transects and -3.8 ± 2.4 cm2 total erosion occurring on the control transect ( P = 0.046). More material was transported on the trail than on the control, 12.9± 2.4 versus 6.0 ± 2.4 cm2 ( P = 0.055), however, deposition levels remained similar on the trail and on the control. Snow compaction from snowshoers and cross-country skiers intensified erosion. Trail gradient was found to be significantly correlated to net changes in material on the trail ( R 2 = 0.89, ρ = -0.98, P = 0.005). This study provides a baseline, showing that non-motorized winter recreation does impact soil erosion rates but more studies are needed. Trail managers should consider mitigation such as water bars, culverts and avoiding building trails with steep gradients, in order to reduce loss of soils on trails and subsequent sedimentation of streams.

Three-Dimensional Analysis of Voids in AM60B Magnesium Tensile Bars Using Computed Tomography Imagery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waters, A M

2001-05-01

In an effort to increase automobile fuel efficiency as well as decrease the output of harmful greenhouse gases, the automotive industry has recently shown increased interest in cast light metals such as magnesium alloys in an effort to increase weight savings. Currently several magnesium alloys such as AZ91 and AM60B are being used in structural applications for automobiles. However, these magnesium alloys are not as well characterized as other commonly used structural metals such as aluminum. This dissertation presents a methodology to nondestructively quantify damage accumulation due to void behavior in three dimensions in die-cast magnesium AM60B tensile bars asmore » a function of mechanical load. Computed tomography data was acquired after tensile bars were loaded up to and including failure, and analyzed to characterize void behavior as it relates to damage accumulation. Signal and image processing techniques were used along with a cluster labeling routine to nondestructively quantify damage parameters in three dimensions. Void analyses were performed including void volume distribution characterization, nearest neighbor distance calculations, shape parameters, and volumetric renderings of voids in the alloy. The processed CT data was used to generate input files for use in finite element simulations, both two- and three-dimensional. The void analyses revealed that the overwhelming source of failure in each tensile bar was a ring of porosity within each bar, possibly due to a solidification front inherent to the casting process. The measured damage parameters related to void nucleation, growth, and coalescence were shown to contribute significantly to total damage accumulation. Void volume distributions were characterized using a Weibull function, and the spatial distributions of voids were shown to be clustered. Two-dimensional finite element analyses of the tensile bars were used to fine-tune material damage models and a three-dimensional mesh of an extracted portion of one tensile bar including voids was generated from CT data and used as input to a finite element analysis.« less

A Handheld Point-of-Care Genomic Diagnostic System

PubMed Central

Myers, Frank B.; Henrikson, Richard H.; Bone, Jennifer; Lee, Luke P.

2013-01-01

The rapid detection and identification of infectious disease pathogens is a critical need for healthcare in both developed and developing countries. As we gain more insight into the genomic basis of pathogen infectivity and drug resistance, point-of-care nucleic acid testing will likely become an important tool for global health. In this paper, we present an inexpensive, handheld, battery-powered instrument designed to enable pathogen genotyping in the developing world. Our Microfluidic Biomolecular Amplification Reader (µBAR) represents the convergence of molecular biology, microfluidics, optics, and electronics technology. The µBAR is capable of carrying out isothermal nucleic acid amplification assays with real-time fluorescence readout at a fraction of the cost of conventional benchtop thermocyclers. Additionally, the µBAR features cell phone data connectivity and GPS sample geotagging which can enable epidemiological surveying and remote healthcare delivery. The µBAR controls assay temperature through an integrated resistive heater and monitors real-time fluorescence signals from 60 individual reaction chambers using LEDs and phototransistors. Assays are carried out on PDMS disposable microfluidic cartridges which require no external power for sample loading. We characterize the fluorescence detection limits, heater uniformity, and battery life of the instrument. As a proof-of-principle, we demonstrate the detection of the HIV-1 integrase gene with the µBAR using the Loop-Mediated Isothermal Amplification (LAMP) assay. Although we focus on the detection of purified DNA here, LAMP has previously been demonstrated with a range of clinical samples, and our eventual goal is to develop a microfluidic device which includes on-chip sample preparation from raw samples. The µBAR is based entirely around open source hardware and software, and in the accompanying online supplement we present a full set of schematics, bill of materials, PCB layouts, CAD drawings, and source code for the µBAR instrument with the goal of spurring further innovation toward low-cost genetic diagnostics. PMID:23936402

FINAL REPORT - Development of High Pressure Hydrogen Storage Tank for Storage and Gaseous Truck Delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, Donald

The “Development of High Pressure Hydrogen Storage Tanks for Storage and Gaseous Truck Delivery” project [DE-FG36-08GO18062] was initiated on 01 July 2008. Hexagon Lincoln (then Lincoln Composites) received grant funding from the U.S. Department of Energy to support the design and development of an improved bulk hauling and storage solution for hydrogen in terms of cost, safety, weight and volumetric efficiency. The development of this capability required parallel development and qualification of large all-composites pressure vessels, a custom ISO container to transport and store said tanks, and performance of trade studies to identify optimal operating pressure for the system. Qualificationmore » of the 250 bar TITAN® module was completed in 2009 with supervision from the American Bureau of Shipping [ABS], and the equipment has been used internationally for bulk transportation of fuel gases since 2010. Phase 1 of the project was successfully completed in 2012 with the issuance of USDOT SP 14951, the special permit authorizing the manufacture, marking, sale and use of TITAN® Mobile Pipeline® equipment in the United States. The introduction of tube trailers with light weight composite tankage has meant that 2 to 3 times as much gaseous fuel can be transported with each trip. This increased hauling efficiency offers dramatically reduced operating costs and has enabled a profitable business model for over-the-road compressed natural gas delivery. The economic drivers of this business opportunity vary from country to country and region to region, but in many places gas distribution companies have realized profitable operations. Additional testing was performed in 2015 to characterize hydrogen-specific operating protocols for use of TITAN® systems in CHG service at 250 bar. This program demonstrated that existing compression and decompression methodologies can efficiently and safely fill and unload lightweight bulk hauling systems. Hexagon Lincoln and U.S. DOE agreed to continue into Phase 2 of the project without pursuing the development of higher pressure capabilities as originally planned. At 250 bar, development of equipment for hydrogen transport is supported by strong activity in the adjacent natural gas transportation sector. Trade studies performed since 2011 indicate optimization of hauling efficiency and system cost for hydrogen transport at about 350 bar (5076 psi). However, due to reduced efficiency of compression of natural gas above 250 bar, 350 bar operation is not an attractive option for natural gas transportation. The CHG market is not developed at this time, and it is difficult to forecast the arrival of significant revenues. On the investment side, the cost to fully qualify a large tank module at 350 bar is estimated at $3MM to $5MM. There is insufficient CHG market definition to support a stand-alone business case for this investment without near term revenue in the adjacent CNG transportation market. Therefore development of a 350 bar TITAN® system was deferred and not pursued under this project. Hexagon Lincoln continues to support the development of tankage and equipment for operation at 350 bar and above; with 700 bar vehicle tanks and 950 bar tanks for ground storage applications. Phase 2 activities were focused on reducing system cost, increasing system capacity, increasing system safety and characterization of polymer material performance specific to hydrogen pressure vessel usage. With the successful launch of TITAN® modules and trailers in natural gas transportation, over 600 units have been produced through the end of 2016, resulting in improved purchasing power for raw materials and manufactured components. This has allowed Hexagon Lincoln to approach the current project goals for system cost. At $590/kg of compressed hydrogen delivered, the system cost of the baseline TITAN® module is below the project’s 2015 target of $730/kg H2 delivered, and very close to the project’s 2020 target of $575/kg H2 delivered. [Based on product pricing in 1Q2017.] Emphasis was placed on configuration of larger capacity systems within the vehicle weights and dimensions allowed on federal and state highways in the United States and other countries. These activities resulted in the design and development of integrated tube trailer systems that have increased delivery capacities by 45%. The hydrogen delivery capacity of our largest system is 845 kg, exceeding the project’s 2015 target of 700 kg H2 delivered. Emerging technologies offering improvement of the safety systems used on the equipment were investigated, with particular focus on improving the reliability and cost of the emergency venting system for fire protection. Finally, investment in our materials laboratory improved detection and characterization of hydrogen-induced damage in polymer materials, supporting the development of operational protocols to avoid damage to pressure vessel liners and valve components.« less

Automatic detection of service initiation signals used in bars

PubMed Central

Loth, Sebastian; Huth, Kerstin; De Ruiter, Jan P.

2013-01-01

Recognizing the intention of others is important in all social interactions, especially in the service domain. Enabling a bartending robot to serve customers is particularly challenging as the system has to recognize the social signals produced by customers and respond appropriately. Detecting whether a customer would like to order is essential for the service encounter to succeed. This detection is particularly challenging in a noisy environment with multiple customers. Thus, a bartending robot has to be able to distinguish between customers intending to order, chatting with friends or just passing by. In order to study which signals customers use to initiate a service interaction in a bar, we recorded real-life customer-staff interactions in several German bars. These recordings were used to generate initial hypotheses about the signals customers produce when bidding for the attention of bar staff. Two experiments using snapshots and short video sequences then tested the validity of these hypothesized candidate signals. The results revealed that bar staff responded to a set of two non-verbal signals: first, customers position themselves directly at the bar counter and, secondly, they look at a member of staff. Both signals were necessary and, when occurring together, sufficient. The participants also showed a strong agreement about when these cues occurred in the videos. Finally, a signal detection analysis revealed that ignoring a potential order is deemed worse than erroneously inviting customers to order. We conclude that (a) these two easily recognizable actions are sufficient for recognizing the intention of customers to initiate a service interaction, but other actions such as gestures and speech were not necessary, and (b) the use of reaction time experiments using natural materials is feasible and provides ecologically valid results. PMID:24009594

Split Hopkinson resonant bar test for sonic-frequency acoustic velocity and attenuation measurements of small, isotropic geological samples.

PubMed

Nakagawa, Seiji

2011-04-01

Mechanical properties (seismic velocities and attenuation) of geological materials are often frequency dependent, which necessitates measurements of the properties at frequencies relevant to a problem at hand. Conventional acoustic resonant bar tests allow measuring seismic properties of rocks and sediments at sonic frequencies (several kilohertz) that are close to the frequencies employed for geophysical exploration of oil and gas resources. However, the tests require a long, slender sample, which is often difficult to obtain from the deep subsurface or from weak and fractured geological formations. In this paper, an alternative measurement technique to conventional resonant bar tests is presented. This technique uses only a small, jacketed rock or sediment core sample mediating a pair of long, metal extension bars with attached seismic source and receiver-the same geometry as the split Hopkinson pressure bar test for large-strain, dynamic impact experiments. Because of the length and mass added to the sample, the resonance frequency of the entire system can be lowered significantly, compared to the sample alone. The experiment can be conducted under elevated confining pressures up to tens of MPa and temperatures above 100 [ordinal indicator, masculine]C, and concurrently with x-ray CT imaging. The described split Hopkinson resonant bar test is applied in two steps. First, extension and torsion-mode resonance frequencies and attenuation of the entire system are measured. Next, numerical inversions for the complex Young's and shear moduli of the sample are performed. One particularly important step is the correction of the inverted Young's moduli for the effect of sample-rod interfaces. Examples of the application are given for homogeneous, isotropic polymer samples, and a natural rock sample. © 2011 American Institute of Physics

The Observation of the Structure of M23C6/ γ Coherent Interface in the 100Mn13 High Carbon High Manganese Steel

NASA Astrophysics Data System (ADS)

Xu, Zhenfeng; Ding, Zhimin; Liang, Bo

2018-03-01

The M23C6 carbides precipitate along the austenite grain boundary in the 100Mn13 high carbon high manganese steel after 1323 K (1050 °C) solution treatment and subsequent 748 K (475 °C) aging treatment. The grain boundary M23C6 carbides not only spread along the grain boundary and into the incoherent austenite grain, but also grow slowly into the coherent austenite grain. On the basis of the research with optical microscope, a further investigation for the M23C6/ γ coherent interface was carried out by transmission electron microscope (TEM). The results show that the grain boundary M23C6 carbides have orientation relationships with only one of the adjacent austenite grains in the same planes: (\\bar{1}1\\bar{1})_{{{M}_{ 2 3} {C}_{ 6} }} //(\\bar{1}1\\bar{1})_{γ } , (\\bar{1}11)_{{{M}_{ 2 3} {C}_{ 6} }} //(\\bar{1}11)_{γ } ,[ 1 10]_{{{M}_{ 2 3} {C}_{ 6} }} //[ 1 10]_{γ } . The flat M23C6/ γ coherent interface lies on the low indexed crystal planes {111}. Moreover, in M23C6/ γ coherent interface, there are embossments which stretch into the coherent austenite grain γ. Dislocations distribute in the embossments and coherent interface frontier. According to the experimental observation, the paper suggests that the embossments can promote the M23C6/ γ coherent interface move. Besides, the present work has analyzed chemical composition of experimental material and the crystal structures of austenite and M23C6, which indicates that the transformation can be completed through a little diffusion for C atoms and a simple variant for austenite unit cell.

Radioactivity of natural and artificial building materials - a comparative study.

PubMed

Szabó, Zs; Völgyesi, P; Nagy, H É; Szabó, Cs; Kis, Z; Csorba, O

2013-04-01

Building materials and their additives contain radioactive isotopes, which can increase both external and internal radioactive exposures of humans. In this study Hungarian natural (adobe) and artificial (brick, concrete, coal slag, coal slag concrete and gas silicate) building materials were examined. We qualified 40 samples based on their radium equivalent, activity concentration, external hazard and internal hazard indices and the determined threshold values of these parameters. Absorbed dose rate and annual effective dose for inhabitants living in buildings made of these building materials were also evaluated. The calculations are based on (226)Ra, (232)Th and (40)K activity concentrations determined by gamma-ray spectrometry. Measured radionuclide concentrations and hence, calculated indices and doses of artificial building materials show a rather disparate distribution compared to adobes. The studied coal slag samples among the artificial building materials have elevated (226)Ra content. Natural, i.e. adobe and also brick samples contain higher amount of (40)K compared to other artificial building materials. Correlation coefficients among radionuclide concentrations are consistent with the values in the literature and connected to the natural geochemical behavior of U, Th and K elements. Seven samples (coal slag and coal slag concrete) exceed any of the threshold values of the calculated hazard indices, however only three of them are considered to be risky to use according to the fact that the building material was used in bulk amount or in restricted usage. It is shown, that using different indices can lead to different conclusions; hence we recommend considering more of the indices at the same time when building materials are studied. Additionally, adding two times their statistical uncertainties to their values before comparing to thresholds should be considered for providing a more conservative qualification. We have defined radon hazard portion to point to the limitations of the internal hazard considerations based on only measured (226)Ra activity concentrations without direct radon measurements. Our data are compared to those obtained in other countries and they provide a good basis to expand the database of radioactivity of building materials and gives information about the safety and situation of the building material industry in this central region of Europe. Copyright © 2012 Elsevier Ltd. All rights reserved.

Interaction of electron neutrino with LSD detector

NASA Astrophysics Data System (ADS)

Ryazhskaya, O. G.; Semenov, S. V.

2016-06-01

The interaction of electron neutrino flux, originating in the rotational collapse mechanism on the first stage of Supernova burst, with the LSD detector components, such as 56Fe (a large amount of this metal is included in as shielding material) and liquid scintillator barNnH2n+2, is being investigated. Both charged and neutral channels of neutrino reaction with 12barN and 56Fe are considered. Experimental data, giving the possibility to extract information for nuclear matrix elements calculation are used. The number of signals, produced in LSD by the neutrino pulse of Supernova 1987A is determined. The obtained results are in good agreement with experimental data.

(BARS) -- Bibliographic Retrieval System Sandia Shock Compression (SSC) database Shock Physics Index (SPHINX) database. Volume 1: UNIX version query guide customized application for INGRES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herrmann, W.; von Laven, G.M.; Parker, T.

1993-09-01

The Bibliographic Retrieval System (BARS) is a data base management system specially designed to retrieve bibliographic references. Two databases are available, (i) the Sandia Shock Compression (SSC) database which contains over 5700 references to the literature related to stress waves in solids and their applications, and (ii) the Shock Physics Index (SPHINX) which includes over 8000 further references to stress waves in solids, material properties at intermediate and low rates, ballistic and hypervelocity impact, and explosive or shock fabrication methods. There is some overlap in the information in the two data bases.

One-dimensional analysis of filamentary composite beam columns with thin-walled open sections

NASA Technical Reports Server (NTRS)

Lo, Patrick K.-L.; Johnson, Eric R.

1986-01-01

Vlasov's one-dimensional structural theory for thin-walled open section bars was originally developed and used for metallic elements. The theory was recently extended to laminated bars fabricated from advanced composite materials. The purpose of this research is to provide a study and assessment of the extended theory. The focus is on flexural and torsional-flexural buckling of thin-walled, open section, laminated composite columns. Buckling loads are computed from the theory using a linear bifurcation analysis and a geometrically nonlinear beam column analysis by the finite element method. Results from the analyses are compared to available test data.

An Evaluation and Comparison of Several Measures of Image Quality for Television Displays

DTIC Science & Technology

1979-01-01

vehicles, buildings, or faces , or they may be artificial much as trn-bar patterns, rectangles, or sine waves. The typical objective image quality assessment...Snyder (1974b) wac able to obtain very good correlations with reaction time and correct responses for a face recognition task. Display quality was varied...recognition versus log JUDA for the target recognition study of Chapter 4, 5) graph of angle oubtended by target at recognitio , versus log JNDA for the

DECO FRECASE (drywall eco-friendly from eggshell and cane bagasse) as an innovation of eco-friendly interior construction

NASA Astrophysics Data System (ADS)

Imron, M. A.; Ahkam, D. N. I.; Hidayat, A. W.

2017-12-01

The number of factories and home industries, both upper and lower middle class certainly adds waste generated, resulting in environmental pollution. The development of buildings is one of the largest contributors to global warming. For that, it takes technological innovations that lead to the criteria of green building. The application of green material is important aspects of environmentally friendly development, the selection of materials on the green material criteria of both roles should be applied continuously in order to realize the environmental sustainability of the material. Utilization Waste eggshell and bagasse which is a community waste, has the potential to become innovative environmentally friendly building materials. The eggshell is composed of 94% calcium carbonate, 1% magnesium carbonate, 1% calcium phosphate, and 4% organic material, especially protein, while the bagasse has a high content of silica (SiO2). In this study, the compounds are used as raw material for making alternative drywall in the form of DECO FRECASE. DECO FRECASE is an innovation of environmentally friendly building materials as an interior wall construction. Through DECO FRECASE, it is expected that building material innovation in Indonesia can be improved and of course environmental problems can be minimized by utilizing it as raw material for building construction.

Invention, design and performance of coconut agrowaste fiberboards for ecologically efficacious buildings

NASA Astrophysics Data System (ADS)

Lokko, Mae-ling Jovenes

As global quantities of waste by-products from food production as well as the range of their applications increase, researchers are realizing critical opportunities to transform the burden of underutilized wastes into ecological profits. Within the tropical hot-humid region, where half the world's current and projected future population growth is concentrated, there is a dire demand for building materials to meet ambitious development schemes and rising housing deficits. However, the building sector has largely overlooked the potential of local agricultural wastes to serve as alternatives to energy-intensive, imported building technologies. Industrial ecologists have recently investigated the use of agrowaste biocomposites to replace conventional wood products that use harmful urea-formaldehyde, phenolic and isocyanate resins. Furthermore, developments in the performance of building material systems with respect to cost, energy, air quality management and construction innovation have evolved metrics about what constitutes material 'upcycling' within building life cycle. While these developments have largely been focused on technical and cost performance, much less attention has been paid to addressing deeply-seated social and cultural barriers to adoption that have sedimented over decades of importation. This dissertation evaluates the development coconut agricultural building material systems in four phases: (i) non-toxic, low-energy production of medium-high density boards (500-1200 kg/m3) from coconut fibers and emerging biobinders; (ii) characterization and evaluation of coconut agricultural building materials hygrothermal performance (iii) scaled-up design development of coconut modular building material systems and (iv) development of a value translation framework for the bottom-up distribution of value to stakeholders within the upcycling framework. This integrated design methodological approach is significant to develop ecological thinking around agrowaste building materials, influence social and cultural acceptability and create value translation frameworks that sufficiently characterize the composite value proposition of upcycled building systems.

JCE Online 99

NASA Astrophysics Data System (ADS)

Holmes, Jon L.

1999-04-01

As I write this, JCE Online is in the middle of being redesigned to make it a more usable resource. By the time you read this, the typical online page for articles of this Journal will look like Figure 1. The page has five main features:

• the page heading with the global menu bar
• the left-hand navigation bar
• the page menu bar near the top of the page and repeated near the bottom
• the main content region in the middle of the page
• the right-hand column of local navigation links

Setting up the criteria and credit-awarding scheme for building interior material selection to achieve better indoor air quality.

PubMed

Niu, J L; Burnett, J

2001-06-01

Methods, standards, and regulations that are aimed to reduce indoor air pollution from building materials are critically reviewed. These are classified as content control and emission control. Methods and standards can be found in both of these two classes. In the regulation domain, only content control is enforced in some countries and some regions, and asbestos is the only building material that is banned for building use. The controlled pollutants include heavy metals, radon, formaldehyde, and volatile organic compounds (VOCs). Emission rate control based upon environment chamber testing is very much in the nature of voluntary product labeling and ranking, and this mainly targets formaldehyde and VOC emissions. It is suggested that radon emission from building materials should be subject to similar emission rate control. A comprehensive set criteria and credit-awarding scheme that encourages the use of low-emission building material is synthesized, and how this scheme can be practiced in building design is proposed and discussed.

MATERIALS FOR MODERNIZATION.

ERIC Educational Resources Information Center

JACKSON, R. GRAHAM

CHOICES AND ISSUES IN SELECTING MATERIALS FOR MODERNIZATION OF SCHOOL BUILDINGS ARE DISCUSSED IN THIS REPORT. BACKGROUND INFORMATION IS INTRODUCED IN TERMS OF REASONS FOR ABANDONMENT, THE CAUSES AND EFFECTS OF SCHOOL BUILDING OBSOLESCENCE, AND PROBLEMS IN THE MODERNIZATION PROCESS. INTERIOR PARTITIONS ARE DISCUSSED IN TERMS OF BUILDING MATERIALS,…

Experimental data showing the thermal behavior of a flat roof with phase change material.

PubMed

Tokuç, Ayça; Başaran, Tahsin; Yesügey, S Cengiz

2015-12-01

The selection and configuration of building materials for optimal energy efficiency in a building require some assumptions and models for the thermal behavior of the utilized materials. Although the models for many materials can be considered acceptable for simulation and calculation purposes, the work for modeling the real time behavior of phase change materials is still under development. The data given in this article shows the thermal behavior of a flat roof element with a phase change material (PCM) layer. The temperature and energy given to and taken from the building element are reported. In addition the solid-liquid behavior of the PCM is tracked through images. The resulting thermal behavior of the phase change material is discussed and simulated in [1] A. Tokuç, T. Başaran, S.C. Yesügey, An experimental and numerical investigation on the use of phase change materials in building elements: the case of a flat roof in Istanbul, Build. Energy, vol. 102, 2015, pp. 91-104.

Determination of concrete cover thickness in a reinforced concrete pillar by observation of the scattered electromagnetic field

NASA Astrophysics Data System (ADS)

Di Gregorio, Pietro Paolo; Frezza, Fabrizio; Mangini, Fabio; Pajewski, Lara

2017-04-01

The electromagnetic scattered field by a reinforced concrete structure is calculated by means of frequency-domain numerical simulations and by making use of the scattered-field formulation. The concrete pillar, used as supporting architectural element, is modelled as a parallelepiped shell made of concrete material inside which are present steel bars. In order to make the model simpler, the steel bars are supposed running parallel to the air-pillar interface. To excite the model, a linearly-polarized plane wave impinging normally with respect to the pillars surface, is adopted. We consider two different polarizations in order to determine the most useful in terms of scattered-field sensitivity. Moreover, a preliminary frequency sweep allows us to choose the most suitable operating frequency depending on the dimensions of the pillar cross-section, the steel bars cross-section and the concrete cover. All the three components of the scattered field are monitored along a line just above the interface air-pillar. The electromagnetic properties of the materials employed in this study are present in the literature and, since a frequency-domain technique is adopted, no further approximation is needed. The results obtained for different values of the concrete cover are compared, with the goal of determining the scattered field dependence on the concrete cover thickness. Considering different concrete cover thicknesses, we want to provide an electromagnetic method to obtain this useful parameter by observation of the scattered electromagnetic field. One of the practical applications of this study in the field of Civil Engineering may be the use of ground penetrating radar (GPR) techniques to monitor the thickness of the concrete that separates the metal bars embedded in the pillar from the outer surface. A correct distance is useful because the concrete cover serves as a protection against external agents avoiding corrosion of the bars that might prejudice the reinforced concrete; it ensures also an optimal transmission and distribution of the adhesion forces in the pillar. Acknowledgement This work is a contribution to COST Action TU1208 "Civil Engineering Applications of Ground Penetrating Radar" (www.GPRadar.eu, www.cost.eu).

Influence of different surface treatments on bond strength of novel CAD/CAM restorative materials to resin cement

PubMed Central

Kömürcüoğlu, Meltem Bektaş; Sağırkaya, Elçin

2017-01-01

PURPOSE To evaluate the effects of different surface treatments on the bond strength of novel CAD/CAM restorative materials to resin cement by four point bending test. MATERIALS AND METHODS The CAD/CAM materials under investigation were e.max CAD, Mark II, Lava Ultimate, and Enamic. A total of 400 bar specimens (4×1.2×12 mm) (n=10) milled from the CAD/CAM blocks underwent various pretreatments (no pretreatment (C), hydrofluoric acid (A), hydrofluoric acid + universal adhesive (Scotchbond) (AS), sandblasting (Sb), and sandblasting + universal adhesive (SbS)). The bars were luted end-to-end on the prepared surfaces with a dual curing adhesive resin cement (Variolink N, Ivoclar Vivadent) on the custom-made stainless steel mold. Ten test specimens for each treatment and material combination were performed with four point bending test method. Data were analyzed using ANOVA and Tukey's test. RESULTS The surface treatment and type of CAD/CAM restorative material showed a significant effect on the four point bending strength (FPBS) (P<.001). For LDC, AS surface treatment showed the highest FPBS results (100.31 ± 10.7 MPa) and the lowest values were obtained in RNC (23.63 ± 9.0 MPa) for control group. SEM analyses showed that the surface topography of CAD/CAM restorative materials was modified after treatments. CONCLUSION The surface treatment of sandblasting or HF acid etching in combination with a universal adhesive containing MDP can be suggested for the adhesive cementation of the novel CAD/CAM restorative materials. PMID:29279763

Modeling of concrete cracking due to corrosion process of reinforcement bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bossio, Antonio, E-mail: antonio.bossio@unina.it; Monetta, Tullio, E-mail: monetta@unina.it; Bellucci, Francesco, E-mail: bellucci@unina.it

The reinforcement corrosion in Reinforced Concrete (RC) is a major reason of degradation for structures and infrastructures throughout the world leading to their premature deterioration before design life was attained. The effects of corrosion of reinforcement are: (i) the reduction of the cross section of the bars, and (ii) the development of corrosion products leading to the appearance of cracks in the concrete cover and subsequent cover spalling. Due to their intrinsic complex nature, these issues require an interdisciplinary approach involving both material science and structural design knowledge also in terms on International and National codes that implemented the conceptmore » of durability and service life of structures. In this paper preliminary FEM analyses were performed in order to simulate pitting corrosion or general corrosion aimed to demonstrate the possibility to extend the results obtained for a cylindrical specimen, reinforced by a single bar, to more complex RC members in terms of geometry and reinforcement. Furthermore, a mechanical analytical model to evaluate the stresses in the concrete surrounding the reinforcement bars is proposed. In addition, a sophisticated model is presented to evaluate the non-linear development of stresses inside concrete and crack propagation when reinforcement bars start to corrode. The relationships between the cracking development (mechanical) and the reduction of the steel section (electrochemical) are provided. Finally, numerical findings reported in this paper were compared to experimental results available in the literature and satisfactory agreement was found.« less

CONTRIBUTIONS OF BUILDING MATERIALS TO INDOOR RADON LEVELS IN FLORIDA BUILDINGS

EPA Science Inventory

The report documents work to characterize potential radon sources in concretes and recommend related changes to Florida's building materials radium standard. (NOTE: The Florida Standard for Radon-resistant Residential Building Construction originally contained a provision to limi...

Integrating the use phase impacts of building materials into near-field LCA characterization

EPA Science Inventory

The characterization of chemical exposures from the use phase of building materials is currently in the earliest stages. While connections have been made between many chemical exposures and building materials and the accompanying human health impacts, currently there do not exist...

Alloy steel nuts for bolting for high-pressure and high-temperature service (ASME SA-194 with additional requirements)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This standard covers alloy steel nuts for bolting for high-pressure and high-temperature service in nuclear and associated applications. This standard does not cover bar or other starting materials. The only implied special considerations for starting materials are that they be capable of passing the required tests when processed into finished products in accordance with this standard.

Portable Device Slices Thermoplastic Prepregs

NASA Technical Reports Server (NTRS)

Taylor, Beverly A.; Boston, Morton W.; Wilson, Maywood L.

1993-01-01

Prepreg slitter designed to slit various widths rapidly by use of slicing bar holding several blades, each capable of slicing strip of preset width in single pass. Produces material evenly sliced and does not contain jagged edges. Used for various applications in such batch processes involving composite materials as press molding and autoclaving, and in such continuous processes as pultrusion. Useful to all manufacturers of thermoplastic composites, and in slicing B-staged thermoset composites.

Static and cyclic loading of fiber-reinforced dental resin.

PubMed

Drummond, James L; Bapna, Mahendra S

2003-05-01

The aim of this study was to evaluate the flexure strength of unidirectional fiber-reinforced resins under static and cyclic loading with and without thermal cycling. The fiber-reinforced resin materials chosen for this project were commercially available endodontic posts and commercially procured bar samples. For all materials, controls for flexure strength were tested in air and in water using three-point loading. Specimens were thermal cycled between 7 and 63 degrees C for 6000 cycles. A staircase approach was used to determine the flexure fatigue limit and scanning microscopy was used to examine the microstructure. The carbon/graphite fiber-reinforced resin posts and the glass FiberKor posts were significantly stronger than the ceramic (zirconia) and the other glass-reinforced resin materials. Thermal cycling caused a significant lowering (11-24%) of the flexure strength for each resin based post system. The ceramic post system decreased only by 2%. Further, for standard size glass fiber-reinforced resin bars, no significant differences between testing in air and water was observed, but a significant difference between static and cyclic loading was noted. The decreases in the strength property due to thermal cycling and the cyclic loading of these materials indicates that their utilization in the oral environment enhances their degradation, and potentially shortens their clinical life.

Sorbent Material Property Requirements for On-Board Hydrogen Storage for Automotive Fuel Cell Systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahluwalia, R. K.; Peng, J-K; Hua, T. Q.

2015-05-25

Material properties required for on-board hydrogen storage in cryogenic sorbents for use with automotive polymer electrolyte membrane (PEM) fuel cell systems are discussed. Models are formulated for physical, thermodynamic and transport properties, and for the dynamics of H-2 refueling and discharge from a sorbent bed. A conceptual storage configuration with in-bed heat exchanger tubes, a Type-3 containment vessel, vacuum insulation and requisite balance-of-plant components is developed to determine the peak excess sorption capacity and differential enthalpy of adsorption for 5.5 wt% system gravimetric capacity and 55% well-to-tank (WTT) efficiency. The analysis also determines the bulk density to which the materialmore » must be compacted for the storage system to reach 40 g.L-1 volumetric capacity. Thermal transport properties and heat transfer enhancement methods are analyzed to estimate the material thermal conductivity needed to achieve 1.5 kg.min(-1) H-2 refueling rate. Operating temperatures and pressures are determined for 55% WTT efficiency and 95% usable H-2. Needs for further improvements in material properties are analyzed that would allow reduction of storage pressure to 50 bar from 100 bar, elevation of storage temperature to 175-200 K from 150 K, and increase of WTT efficiency to 57.5% or higher.« less

Enantioseparation of omeprazole--effect of different packing particle size on productivity.

PubMed

Enmark, Martin; Samuelsson, Jörgen; Forssén, Patrik; Fornstedt, Torgny

2012-06-01

Enantiomeric separation of omeprazole has been extensively studied regarding both product analysis and preparation using several different chiral stationary phases. In this study, the preparative chiral separation of omeprazole is optimized for productivity using three different columns packed with amylose tris (3,5-dimethyl phenyl carbamate) coated macroporous silica (5, 10 and 25 μm) with a maximum allowed pressure drop ranging from 50 to 400 bar. This pressure range both covers low pressure process systems (50-100 bar) and investigates the potential for allowing higher pressure limits in preparative applications in a future. The process optimization clearly show that the larger 25 μm packing material show higher productivity at low pressure drops whereas with increasing pressure drops the smaller packing materials have substantially higher productivity. Interestingly, at all pressure drops, the smaller packing material result in lower solvent consumption (L solvent/kg product); the higher the accepted pressure drop, the larger the gain in reduced solvent consumption. The experimental adsorption isotherms were not identical for the different packing material sizes; therefore all calculations were recalculated and reevaluated assuming identical adsorption isotherms (with the 10 μm isotherm as reference) which confirmed the trends regarding productivity and solvent consumption. Copyright © 2012 Elsevier B.V. All rights reserved.

Dark, Thin Fracture-Filling Material

NASA Image and Video Library

2015-11-11

These images and overlay bar charts from the Chemistry and Camera (ChemCam) instrument on NASA's Curiosity Mars rover indicate where some high-potassium material is localized within mineral veins at "Garden City." The two images are from ChemCam's Remote Micro-Imager. Each covers an area just over an inch wide (scale bars are in millimeters) in veins at the Garden City site on lower Mount Sharp. The overlay charts show comparisons of potassium (blue) and iron (red) in the mineral veins' compositions determined by reading the spectra of light induced by zapping points in each area with ChemCam's laser. Mineral veins such as these form where fluids move through fractured rocks, depositing minerals in the fractures and affecting chemistry of the surrounding rock. The thin layer of dark fracture-filling material in the image on the right contains much more potassium than the other local material on the left, indicating either different fluid compositions or local variations in the rock. The image on the left was taken on April 4, 2015, during the 946th Martian day, or sol, of Curiosity's work on Mars. The image on the right was taken on Sol 936, on March 25, 2015. A broader view of the prominent mineral veins at Garden City is at PIA19161. http://photojournal.jpl.nasa.gov/catalog/PIA19923

Application of magnetoelastic materials in spatiotemporally modulated phononic crystals for nonreciprocal wave propagation

NASA Astrophysics Data System (ADS)

Ansari, M. H.; Attarzadeh, M. A.; Nouh, M.; Karami, M. Amin

2018-01-01

In this paper, a physical platform is proposed to change the properties of phononic crystals in space and time in order to achieve nonreciprocal wave transmission. The utilization of magnetoelastic materials in elastic phononic systems is studied. Material properties of magnetoelastic materials change significantly with an external magnetic field. This property is used to design systems with a desired wave propagation pattern. The properties of the magnetoelastic medium are changed in a traveling wave pattern, which changes in both space and time. A phononic crystal with such a modulation exhibits one-way wave propagation behavior. An extended transfer matrix method (TMM) is developed to model a system with time varying properties. The stop band and the pass band of a reciprocal and a nonreciprocal bar are found using this method. The TMM is used to find the transfer function of a magnetoelastic bar. The obtained results match those obtained via the theoretical Floquet-Bloch approach and numerical simulations. It is shown that the stop band in the transfer function of a system with temporal varying property for the forward wave propagation is different from the same in the backward wave propagation. The proposed configuration enables the physical realization of a class of smart structures that incorporates nonreciprocal wave propagation.

[Opinion of administrative personnel about smoke-free regulations].

PubMed

Wojtysiak, Piotr; Polańska, Kinga; Bak-Romaniszyn, Leokadia; Czarnecka, Karolina; Kaleta, Dorota

2010-01-01

The aim of the study was to analyze the opinion of administrative personnel in school on smoke-free regulations. The study population consisted of 320 subjects. Among the study population questionnaire was conducted including socio-demographic characteristic, smoking and SHS profile. Detail information was collected about opinion on smoke-free public places such as offices, other workplaces, health and educational buildings, restaurants and bars. About 22% of study population declared current tobacco smoking. More current everyday smoking was observed among men comparing to women (17.8% vs. 9.1%; p < 0.05). The study indicated that high percentage support total ban of smoking in public offices (84%), health care buildings (89%), and educational buildings (86%). 60% of the study subject were in favor of smoke-fee restaurants and 38% sypport smoke-free burs, pubs and clubs. The strong approval for ban on tobacco product advertising was indicated by 41% of respondents and 38% of them expect pictorial warnings on tobacco packs.

Torsional Split Hopkinson Bar Optimization

DTIC Science & Technology

2012-04-10

EML 4905 Senior Design Project A B.S. THESIS PREPARED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE DEGREE OF BACHELOR OF...fulfillment of the requirements in EML 4511. The contents represent the opinion of the authors and not the Department of Mechanical and Materials

Warstopper Material Supply Chain Risk Assessments

DTIC Science & Technology

2012-05-22

Steel : – Grade 300M for landing gear components and combat vehicle torsion bars – Grade M50 for bearings • NOMEX® Fiber – Fire retardant...vital domestic industry (not common) Warstopper Program Industrial Base Preparedness Past Investment Items: Class IX: Specialty Steel Benefit

Evaluation of alternative dowel bar materials and coatings.

DOT National Transportation Integrated Search

2011-11-01

This study provided for a continuation of the long-term performance evaluation of 1.5-in (38-mm) diameter FRP dowels : and Type 304 stainless steel solid dowels or mortar-filled tubes compared to epoxy-coated dowels. This primarily : included an eval...

Driving out errors through tight integration between software and automation.

PubMed

Reifsteck, Mark; Swanson, Thomas; Dallas, Mary

2006-01-01

A clear case has been made for using clinical IT to improve medication safety, particularly bar-code point-of-care medication administration and computerized practitioner order entry (CPOE) with clinical decision support. The equally important role of automation has been overlooked. When the two are tightly integrated, with pharmacy information serving as a hub, the distinctions between software and automation become blurred. A true end-to-end medication management system drives out errors from the dockside to the bedside. Presbyterian Healthcare Services in Albuquerque has been building such a system since 1999, beginning by automating pharmacy operations to support bar-coded medication administration. Encouraged by those results, it then began layering on software to further support clinician workflow and improve communication, culminating with the deployment of CPOE and clinical decision support. This combination, plus a hard-wired culture of safety, has resulted in a dramatically lower mortality and harm rate that could not have been achieved with a partial solution.

The readout chain for the bar PANDA MVD strip detector

NASA Astrophysics Data System (ADS)

Schnell, R.; Brinkmann, K.-Th.; Di Pietro, V.; Kleines, H.; Goerres, A.; Riccardi, A.; Rivetti, A.; Rolo, M. D.; Sohlbach, H.; Zaunick, H.-G.

2015-02-01

The bar PANDA (antiProton ANnihilation at DArmstadt) experiment will study the strong interaction in annihilation reactions between an antiproton beam and a stationary gas jet target. The detector will comprise different sub-detectors for tracking, particle identification and calorimetry. The Micro-Vertex Detector (MVD) as the innermost part of the tracking system will allow precise tracking and detection of secondary vertices. For the readout of the double-sided silicon strip sensors a custom-made ASIC is being developed, employing the Time-over-Threshold (ToT) technique for digitization and utilize time-to-digital converters (TDC) to provide a high-precision time stamp of the hit. A custom-made Module Data Concentrator ASIC (MDC) will multiplex the data of all front-ends of one sensor towards the CERN-developed GBT chip set (GigaBit Transceiver). The MicroTCA-based MVD Multiplexer Board (MMB) at the off-detector site will receive and concentrate the data from the GBT links and transfer it to FPGA-based compute nodes for global event building.

Guidelines for Assessment and Abatement of Asbestos-Containing Materials in Buildings.

ERIC Educational Resources Information Center

Pielert, James H.; Mathey, Robert G.

This report presents guidelines, based on available information, for the assessment and abatement of asbestos-containing materials in buildings. Section 1 provides background information on the history and use of asbestos-containing products in buildings, the characteristics of asbestos fibers, products and materials containing asbestos, and…

People, planet and profit: Unintended consequences of legacy building materials.

PubMed

Zimmer, Anthony T; Ha, HakSoo

2017-12-15

Although an explosion of new building materials are being introduced into today's market, adequate up-front research into their chemical and physical properties as well as their potential health and environmental consequences is lacking. History has provided us with several examples where building materials were broadly deployed into society only to find that health and environmental problems resulted in unintended sustainability consequences. In the following paper, we use lead and asbestos as legacy building materials to show their similar historical trends and sustainability consequences. Our research findings show unintended consequences such as: increased remediation and litigation costs; adverse health effects; offshoring of related industries; and impediments to urban revitalization. As numerous new building materials enter today's market, another building material may have already been deployed, representing the next "asbestos." This paper also proposes an alternative methodology that can be applied in a cost-effective way into existing and upcoming building materials, to minimize and prevent potential unintended consequences and create a pathway for sustainable communities. For instance, our findings show that this proposed methodology could have prevented the unintended incurred sustainability costs of approximately $272-$359 billion by investing roughly $24 million in constant 2014 U.S. dollars on up-front research into lead and asbestos. Published by Elsevier Ltd.

Measurement of the high-temperature Seebeck coefficient of thin films by means of an epitaxially regrown thermometric reference material.

PubMed

Ramu, Ashok T; Mages, Phillip; Zhang, Chong; Imamura, Jeffrey T; Bowers, John E

2012-09-01

The Seebeck coefficient of a typical thermoelectric material, silicon-doped InGaAs lattice-matched to InP, is measured over a temperature range from 300 K to 550 K. By depositing and patterning a thermometric reference bar of silicon-doped InP adjacent to a bar of the material under test, temperature differences are measured directly. This is in contrast to conventional two-thermocouple techniques that subtract two large temperatures to yield a small temperature difference, a procedure prone to errors. The proposed technique retains the simple instrumentation of two-thermocouple techniques while eliminating the critical dependence of the latter on good thermal contact. The repeatability of the proposed technique is demonstrated to be ±2.6% over three temperature sweeps, while the repeatability of two-thermocouple measurements is about ±5%. The improved repeatability is significant for reliable reporting of the ZT figure of merit, which is proportional to the square of the Seebeck coefficient. The accuracy of the proposed technique depends on the accuracy with which the high-temperature Seebeck coefficient of the reference material may be computed or measured. In this work, the Seebeck coefficient of the reference material, n+ InP, is computed by rigorous solution of the Boltzmann transport equation. The accuracy and repeatability of the proposed technique can be systematically improved by scaling, and the method is easily extensible to other material systems currently being investigated for high thermoelectric energy conversion efficiency.

Development of a New Method to Investigate the Dynamic Friction Behavior of Interfaces Using a Kolsky Tension Bar

DOE PAGES

Sanborn, B.; Song, B.; Nishida, E.

2017-11-02

In order to understand interfacial interaction of a bi-material during an impact loading event, the dynamic friction coefficient is one of the key parameters that must be characterized and quantified. In this study, a new experimental method to determine the dynamic friction coefficient between two metals was developed by using a Kolsky tension bar and a custom-designed friction fixture. Polyvinylidene fluoride (PVDF) force sensors were used to measure the normal force applied to the friction tribo pairs and the friction force was measured with conventional Kolsky tension bar method. To evaluate the technique, the dynamic friction coefficient between 4340 steelmore » and 7075-T6 aluminum was investigated at an impact speed of approximately 8 m/s. Additionally, the dynamic friction coefficient of the tribo pairs with varied surface roughness was also investigated. The data suggest that higher surface roughness leads to higher friction coefficients at the same speed of 8 m/s.« less

Micromirror with large-tilting angle using Fe-based metallic glass.

PubMed

Lee, Jae-Wung; Lin, Yu-Ching; Kaushik, Neelam; Sharma, Parmanand; Makino, Akihiro; Inoue, Akihisa; Esashi, Masayoshi; Gessner, Thomas

2011-09-01

For enhancing the micromirror properties like tilting angle and stability during actuation, Fe-based metallic glass (MG) was applied for torsion bar material. A micromirror with mirror-plate diameter of 900 μm and torsion bar dimensions length 250 μm, width 30 μm and thickness 2.5 μm was chosen for the tilting angle tests, which were performed by permanent magnets and electromagnet setup. An extremely large tilting angle of over -270° was obtained from an activation test by permanent magnet that has approximately 0.2 T of magnetic strength. A large mechanical tilting angle of over -70° was obtained by applying approximately 1.1 mT to the mirror when 93 mAwas applied to solenoid setup. The large-tilting angle of the micromirror is due to the torsion bar, which was fabricated with Fe-based MG thin film that has large elastic strain limit, fracture toughness, and excellent magnetic property.

Microwave absorption studies on high-T sub c superconductors and related materials II; Electron spin resonance of DPPH coated on Y sub 1 Ba sub 2 Cu sub 3 O sub y as a probe of magnetic field variations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sugawara, K.; Baar, D.J.; Shiohara, Y.

1991-05-10

This paper reports on the ESR linewidth ({Delta}{ital H}{sub p{bar p}}) of DPPH coated on the surface of powder specimens of Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub y} studied under various magnetic field and temperature conditions. {Delta}{ital H}{sub p{bar p}} increases substantially with decreasing temperature in the field cooled case, whereas almost no linewidth broadening was found in the zero field cooled case. {Delta}{ital H}{sub p{bar p}} was found to be sensitive to the applied magnetic field. This effect was very pronounced at temperatures lower than 40 K, but decreased strongly with increasing temperature. The broadening of the resonance lineshape has beenmore » attributed to spatial and temporal variations of the fluxon distribution in the powder particles.« less

Numerical Study on Section Constitutive Relations of Members Reinforced by Steel-BFRP Composite Bars

NASA Astrophysics Data System (ADS)

Xiao, Tongliang; Qiu, Hongxing

2017-06-01

Steel-Basalt FRP Composite Bar (S-BFCB) is a new kind of substitute material for longitudinal reinforcement, with high elastic modulus, stable post-yield stiffness and excellent corrosive resistance. Based on mechanical properties of S-BFCB and the plane cross-section assumption, the moment-curvature curves of beam and column members are simulated. Some parameters such as equivalent rebar ratio, postyeild stiffness, concrete strength and axial compression ratio of column were discussed. Results show that the constitutive relation of the cross section is similar with RC member in elastic and cracking stages, while different in post-yield stage. With the increase of postyeild stiffness ratio of composite bar, the ultimate bearing capacity of component improved observably, member may turn out over-reinforced phenomenon, concrete crushing may appear before the fibersarefractured. The effect of concrete strength increase in lower postyeild stiffness ratio is not obvious than in higher. The increase of axial compression ratio has actively influence on bearing capacity of column, but decreases on the ductility.

Hyperspectral depth-profiling with deep Raman spectroscopy for detecting chemicals in building materials.

PubMed

Cho, Youngho; Song, Si Won; Sung, Jiha; Jeong, Young-Su; Park, Chan Ryang; Kim, Hyung Min

2017-09-25

Toxic chemicals inside building materials have long-term harmful effects on human bodies. To prevent secondary damage caused by the evaporation of latent chemicals, it is necessary to detect the chemicals inside building materials at an early stage. Deep Raman spectroscopy is a potential candidate for on-site detection because it can provide molecular information about subsurface components. However, it is very difficult to spectrally distinguish the Raman signal of the internal chemicals from the background signal of the surrounding materials and to acquire the geometric information of chemicals. In this study, we developed hyperspectral wide-depth spatially offset Raman spectroscopy coupled with a data processing algorithm to identify toxic chemicals, such as chemical warfare agent (CWA) simulants in building materials. Furthermore, the spatial distribution of the chemicals and the thickness of the building material were also measured from one-dimensional (1D) spectral variation.

Sustainable regulation of construction.

PubMed

2000-11-01

The seminar examined the role building codes and regulations can have in promoting a more sustainable approach to construction, particularly through their application to non-industrial building materials. A range of building materials such as straw, bamboo, rammed earth, adobe, and cob (a mixture of clay and chopped straw) were described and illustrated by slides to show their building potential. The current codes have a prime concern to protect the health and safety of people from the built environment. They have been developed almost exclusively for mainstream industrial materials and methods of construction, which makes them difficult to use with alternative, indigenous, or non-industrial building materials, even though those materials may be considered more sustainable. The argument was put forward that with only one-third of the world population living in modern industrial buildings today, it is not sustainable to re-house the remaining rapidly expanding population in high technology dwellings. Many of the low technology building materials and methods now used by the majority of people in the world need only incremental improvement to be equal or superior to many of their industrial replacements. Since these can be more sustainable methods of building, there needs to be an acceptance of the use of alternative materials, particularly in the developing parts of the world, where they are being rejected for less sustainable industrial methods. However, many codes make it difficult to use non-industrial materials; indeed, many of the industrial materials would not meet the demands that must be now met if they were now being introduced as new materials. Consequently, there is a need to develop codes to facilitate the use of a wider range of materials than in current use, and research is needed to assist this development. Sustainable regulation should take into account the full range of real impacts that materials and systems have in areas such as resource use and depletion, toxicity of the processes that produce them, and their potential for re-use and recyclability.

Analysis of variability in additive manufactured open cell porous structures.

PubMed

Evans, Sam; Jones, Eric; Fox, Pete; Sutcliffe, Chris

2017-06-01

In this article, a novel method of analysing build consistency of additively manufactured open cell porous structures is presented. Conventionally, methods such as micro computed tomography or scanning electron microscopy imaging have been applied to the measurement of geometric properties of porous material; however, high costs and low speeds make them unsuitable for analysing high volumes of components. Recent advances in the image-based analysis of open cell structures have opened up the possibility of qualifying variation in manufacturing of porous material. Here, a photogrammetric method of measurement, employing image analysis to extract values for geometric properties, is used to investigate the variation between identically designed porous samples measuring changes in material thickness and pore size, both intra- and inter-build. Following the measurement of 125 samples, intra-build material thickness showed variation of ±12%, and pore size ±4% of the mean measured values across five builds. Inter-build material thickness and pore size showed mean ranges higher than those of intra-build, ±16% and ±6% of the mean material thickness and pore size, respectively. Acquired measurements created baseline variation values and demonstrated techniques suitable for tracking build deviation and inspecting additively manufactured porous structures to indicate unwanted process fluctuations.

Comparative Study on the Cost of Building Public House Construction Using Red Brick and Interlock Brick Building Material in the City of Banda Aceh

NASA Astrophysics Data System (ADS)

Malahayati, Nurul; Hayati, Yulia; Nursaniah, Cut; Firsa, T.; Fachrurrazi; Munandar, Aris

2018-05-01

Red brick and interlocking brick are the building materials that are often used for wall installation work on houses construction. In the development of building materials technology and cost savings, interlocking brick can be alternative to replace red bricks. In Aceh Province, the use of interlocking bricks is less popular compared to other big cities in Indonesia. Interlocking brick is made from a mixture of clay, concrete sand and compacted cement and one of the environmentally friendly materials because it does not burn the process like red brick material. It is named interlocking brick because the installation method is locked together and it serves as a structural and partition wall of residential buildings. The aims of this study are to compare the cost of building a house in Banda Aceh City using red brick and interlock brick building materials. The data were obtained from interviews and questionnaires distributed to respondents who had built houses in Banda Aceh City. The results concluded that the house construction cost using interlock brick offer lower construction cost at comparable quality rather than using red brick.

Research on the Application of GRC Material in Exhibition Decoration Engineering

NASA Astrophysics Data System (ADS)

Cai, Yan

2018-03-01

Glass fiber reinforced cement (GRC) is a kind of new building material which is based on cement and take the alkali resistant glass fiber as reinforcing material. It is mainly used in building decoration project and it has many advantages like environmental protection, economical, practical modeling and others. This paper mainly studies the concrete application of GRC material in exhibition building decoration project.

Natural radioactivity and radiation hazards in some building materials used in Isparta, Turkey

NASA Astrophysics Data System (ADS)

Mavi, B.; Akkurt, I.

2010-09-01

The activity concentrations of uranium, thorium and potassium can vary from material to material and it should be measured as the radiation is hazardous for human health. Thus first studies have been planned to obtain radioactivity of building material used in the Isparta region of Turkey. The radioactivity of some building materials used in this region has been measured using a γ-ray spectrometry, which contains a NaI(Tl) detector connected to MCA. The specific activity for 226Ra, 232Th and 40K, from the selected building materials, were in the range 17.91-58.88, 6.77-19.49 and 65.72-248.76 Bq/kg, respectively. Absorbed dose rate in air ( D), annual effective dose (AED), radium equivalent activities (Ra eq), and external hazard index ( Hex) associated with the natural radionuclide are calculated to assess the radiation hazard of the natural radioactivity in the building materials. It was found that none of the results exceeds the recommended limit value.

METHOD FOR SOLDERING NORMALLY NON-SOLDERABLE ARTICLES

DOEpatents

McGuire, J.C.

1959-11-24

Methods are presented for coating and joining materials which are considered difficult to solder by utilizing an abrasive wheel and applying a bar of a suitable coating material, such as Wood's metal, to the rotating wheel to fill the cavities of the abrasive wheel and load the wheel with the coating material. The surface of the base material is then rubbed against the loaded rotating wheel, thereby coating the surface with the soft coating metal. The coating is a cohesive bonded layer and holds the base metal as tenaciously as a solder holds to easily solderable metals.

10 CFR 433.3 - Materials incorporated by reference.

Code of Federal Regulations, 2011 CFR

2011-01-01

... CONSTRUCTION OF NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.3 Materials... Buildings Except Low-Rise Residential Buildings, January 2004, American Society of Heating Refrigerating and...

10 CFR 433.3 - Materials incorporated by reference.

Code of Federal Regulations, 2010 CFR

2010-01-01

... CONSTRUCTION OF NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.3 Materials... Buildings Except Low-Rise Residential Buildings, January 2004, American Society of Heating Refrigerating and...

The Grain-size Patchiness of Braided Gravel-Bed Streams - example of the Urumqi River (northeast Tian Shan, China)

NASA Astrophysics Data System (ADS)

Guerit, L.; Barrier, L.; Narteau, C.; Métivier, F.; Liu, Y.; Lajeunesse, E.; Gayer, E.; Meunier, P.; Malverti, L.; Ye, B.

2014-02-01

In gravel-bed rivers, sediments are often sorted into patches of different grain-sizes, but in braided streams, the link between this sorting and the channel morpho-sedimentary elements is still unclear. In this study, the size of the bed sediment in the shallow braided gravel-bed Urumqi River is characterized by surface-count and volumetric sampling methods. Three morpho-sedimentary elements are identified in the active threads of the river: chutes at flow constrictions, which pass downstream to anabranches and bars at flow expansions. The surface and surface-layer grain-size distributions of these three elements show that they correspond to only two kinds of grain-size patches: (1) coarse-grained chutes, coarser than the bulk river bed, and (2) finer-grained anabranches and bars, consistent with the bulk river bed. In cross-section, the chute patches are composed of one coarse-grained top layer, which can be interpreted as a local armour layer overlying finer deposits. In contrast, the grain size of the bar-anabranch patches is finer and much more homogeneous in depth than the chute patches. Those patches, which are features of lateral and vertical sorting associated to the transport dynamics that build braided patterns, may be typical of active threads in shallow gravel-bed rivers and should be considered in future works on sorting processes and their geomorphologic and stratigraphic results.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao Hanqing; Fu Zhiguo; Lu Xiaoguang

Guided by the sedimentation theory and knowledge of modern and ancient fluvial deposition and utilizing the abundant information of sedimentary series, microfacies type and petrophysical parameters from well logging curves of close spaced thousands of wells located in a large area. A new method for establishing detailed sedimentation and permeability distribution models for fluvial reservoirs have been developed successfully. This study aimed at the geometry and internal architecture of sandbodies, in accordance to their hierarchical levels of heterogeneity and building up sedimentation and permeability distribution models of fluvial reservoirs, describing the reservoir heterogeneity on the light of the river sedimentarymore » rules. The results and methods obtained in outcrop and modem sedimentation studies have successfully supported the study. Taking advantage of this method, the major producing layers (PI{sub 1-2}), which have been considered as heterogeneous and thick fluvial reservoirs extending widely in lateral are researched in detail. These layers are subdivided into single sedimentary units vertically and the microfacies are identified horizontally. Furthermore, a complex system is recognized according to their hierarchical levels from large to small, meander belt, single channel sandbody, meander scroll, point bar, and lateral accretion bodies of point bar. The achieved results improved the description of areal distribution of point bar sandbodies, provide an accurate and detailed framework model for establishing high resolution predicting model. By using geostatistic technique, it also plays an important role in searching for enriched zone of residual oil distribution.« less

Constitutively active mutants of the alpha 1B-adrenergic receptor: role of highly conserved polar amino acids in receptor activation.

PubMed Central

Scheer, A; Fanelli, F; Costa, T; De Benedetti, P G; Cotecchia, S

1996-01-01

Site-directed mutagenesis and molecular dynamics simulations of the alpha 1B-adrenergic receptor (AR) were combined to explore the potential molecular changes correlated with the transition from R (inactive state) to R (active state). Using molecular dynamics analysis we compared the structural/dynamic features of constitutively active mutants with those of the wild type and of an inactive alpha 1B-AR to build a theoretical model which defines the essential features of R and R. The results of site-directed mutagenesis were in striking agreement with the predictions of the model supporting the following hypothesis. (i) The equilibrium between R and R depends on the equilibrium between the deprotonated and protonated forms, respectively, of D142 of the DRY motif. In fact, replacement of D142 with alanine confers high constitutive activity to the alpha 1B-AR. (ii) The shift of R143 of the DRY sequence out of a conserved 'polar pocket' formed by N63, D91, N344 and Y348 is a feature common to all the active structures, suggesting that the role of R143 is fundamental for mediating receptor activation. Disruption of these intramolecular interactions by replacing N63 with alanine constitutively activates the alpha 1B-AR. Our findings might provide interesting generalities about the activation process of G protein-coupled receptors. Images PMID:8670860

Analysis of the Potential Impact of Additive Manufacturing on Army Logistics

DTIC Science & Technology

2013-11-06

building 3-D objects layer-by-layer. The examination of the primary methods provided the baseline characteristics for building a process timeline for...Figure 2, build material and support material on spools are fed through an extrusion head that force out the material onto a foam base on a build...we researched was selective layer sintering (SLS). According to Freedman (2012), In sintering, a thin layer of powdered metal or thermoplastic is

Effects of Post-Weld Heat Treatment on the Microstructure and Toughness of Flash Butt Welded High-Strength Low-Alloy Steel

NASA Astrophysics Data System (ADS)

Shajan, Nikhil; Arora, Kanwer Singh; Asati, Brajesh; Sharma, Vikram; Shome, Mahadev

2018-04-01

Effect of post-weld heat treatment on the weld microstructure, texture, and its correlation to the toughness of flash butt welded joints were investigated. Upon flash butt welding, the α and γ-fiber in the parent material converted to Goss (110)[001], rotated Goss (110)[1 \\bar{1} 0], and rotated cube (001)[1 \\bar{1} 0], (001)[ \\overline{11} 0] textures along the fracture plane. Formation of these detrimental texture components was a result of shear deformation and recrystallization of austenite at temperatures above T nr resulting in a drop of toughness at the weld zone. Inter-critical and sub-critical annealing cycles proved to be less effective in reducing the Goss (110)[001], rotated Goss (110)[1 \\bar{1} 0], and rotated cube (001)[1 \\bar{1} 0], (001)[ \\overline{11} 0] texture components, and therefore, toughness values remained unaffected. Post-weld heat treatment in the austenite phase field at 1000 °C for 5 seconds resulted in the formation of new grains with different orientations leading to a reduction in the texture intensities of both Goss and rotated Goss components and therefore improved weld zone toughness. Prolonged annealing time was found to be ineffective in improving the toughness due to grain growth.

Carbon Nanotube-Reinforced Aluminum Matrix Composites Produced by High-Energy Ball Milling

NASA Astrophysics Data System (ADS)

Travessa, Dilermando N.; da Rocha, Geovana V. B.; Cardoso, Kátia R.; Lieblich, Marcela

2017-05-01

Although multiwall carbon nanotubes (MWCNT) are promising materials to strengthen lightweight aluminum matrix composites, their dispersion into the metallic matrix is challenge. In the present work, MWCNT were dispersed into age-hardenable AA6061 aluminum alloy by high-energy ball milling and the blend was subsequently hot-extruded. The composite bars obtained were heat-treated by solution heat treatment at 520 °C and artificially aged at 177 °C for 8 h, in order to reach the T6 temper. Special attention was given to the integrity of the MWCNT along the entire composite production. The microstructure of the obtained bars was evaluated by optical and scanning electron microscopy, and the mechanical properties were evaluated by Vickers microhardness tests. Raman spectroscopy, x-ray diffraction and transmission electron microscopy were employed to evaluate the structural integrity of MWCNT. It was found that milling time is critical to reach a proper dispersion of the reinforcing phase. The composite hardness increased up to 67% with the dispersion of 2% in weight of MWCNT, when comparing with un-reinforced bars produced by similar route. However, age hardening was not observed in composite bars after heat treatment. It was also found that MWCNT continuously degraded along the process, being partially converted into Al4C3 in the final composite.

High power diode lasers for solid-state laser pumps

NASA Technical Reports Server (NTRS)

Linden, Kurt J.; Mcdonnell, Patrick N.

1994-01-01

The development and commercial application of high power diode laser arrays for use as solid-state laser pumps is described. Such solid-state laser pumps are significantly more efficient and reliable than conventional flash-lamps. This paper describes the design and fabrication of diode lasers emitting in the 780 - 900 nm spectral region, and discusses their performance and reliability. Typical measured performance parameters include electrical-to-optical power conversion efficiencies of 50 percent, narrow-band spectral emission of 2 to 3 nm FWHM, pulsed output power levels of 50 watts/bar with reliability values of over 2 billion shots to date (tests to be terminated after 10 billion shots), and reliable operation to pulse lengths of 1 ms. Pulse lengths up to 5 ms have been demonstrated at derated power levels, and CW performance at various power levels has been evaluated in a 'bar-in-groove' laser package. These high-power 1-cm stacked-bar arrays are now being manufactured for OEM use. Individual diode laser bars, ready for package-mounting by OEM customers, are being sold as commodity items. Commercial and medical applications of these laser arrays include solid-state laser pumping for metal-working, cutting, industrial measurement and control, ranging, wind-shear/atmospheric turbulence detection, X-ray generation, materials surface cleaning, microsurgery, ophthalmology, dermatology, and dental procedures.

Operation of the ORNL High Particle Flux Helicon Plasma Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goulding, Richard Howell; Biewer, Theodore M; Caughman, John B

2011-01-01

A high power, high particle flux rf-based helicon plasma source has been constructed at ORNL and operated at power levels up to 30 kW. High-density hydrogen and helium plasmas have been produced. The source has been designed as the basis for a linear plasma materials interaction (PMI) test facility that will generate particle fluxes Gamma(p) > 10(23) M-3 s(-1), and utilize additional ion and electron cyclotron heating to produce high parallel (to the magnetic field) heat fluxes of similar to 10 MW/m(2). An rf-based source for PMI research is of interest because high plasma densities are generated with no internalmore » electrodes, allowing true steady state operation with minimal impurity generation. The ORNL helicon source has a diameter of 15 cm and to-date has operated at a frequency f = 13.56 MHz, with magnetic field strength vertical bar B vertical bar in the antenna region up to similar to 0.15 T. Maximum densities of 3 x 10(19) M-3 in He and 2.5 x 10(19) m(-3) in H have been achieved. Radial density profiles have been seen to be dependent on the axial vertical bar B vertical bar profile.« less

Network of vertically c-oriented prismatic InN nanowalls grown on c-GaN/sapphire template by chemical vapor deposition technique

NASA Astrophysics Data System (ADS)

Barick, B. K.; Saroj, Rajendra Kumar; Prasad, Nivedita; Sutar, D. S.; Dhar, S.

2018-05-01

Networks of vertically c-oriented prism shaped InN nanowalls, are grown on c-GaN/sapphire templates using a CVD technique, where pure indium and ammonia are used as metal and nitrogen precursors. A systematic study of the growth, structural and electronic properties of these samples shows a preferential growth of the islands along [ 1 1 2 bar 0 ] and [0 0 0 1] directions leading to the formation of such a network structure, where the vertically [0 0 0 1] oriented tapered walls are laterally align along one of the three [ 1 1 2 bar 0 ] directions. Inclined facets of these walls are identified as semipolar (1 1 2 bar 2) -planes of wurtzite InN. Onset of absorption for these samples is observed to be higher than the band gap of InN suggesting a high background carrier concentration in this material. Study of the valence band edge through XPS indicates the formation of positive depletion regions below the surface of the side facets [(1 1 2 bar 2) -planes] of the walls. This is in contrast with the observation for c-plane InN epilayers, where electron accumulation is often reported below the top surface.

Quantitative analysis of perfumes in talcum powder by using headspace sorptive extraction.

PubMed

Ng, Khim Hui; Heng, Audrey; Osborne, Murray

2012-03-01

Quantitative analysis of perfume dosage in talcum powder has been a challenge due to interference of the matrix and has so far not been widely reported. In this study, headspace sorptive extraction (HSSE) was validated as a solventless sample preparation method for the extraction and enrichment of perfume raw materials from talcum powder. Sample enrichment is performed on a thick film of poly(dimethylsiloxane) (PDMS) coated onto a magnetic stir bar incorporated in a glass jacket. Sampling is done by placing the PDMS stir bar in the headspace vial by using a holder. The stir bar is then thermally desorbed online with capillary gas chromatography-mass spectrometry. The HSSE method is based on the same principles as headspace solid-phase microextraction (HS-SPME). Nevertheless, a relatively larger amount of extracting phase is coated on the stir bar as compared to SPME. Sample amount and extraction time were optimized in this study. The method has shown good repeatability (with relative standard deviation no higher than 12.5%) and excellent linearity with correlation coefficients above 0.99 for all analytes. The method was also successfully applied in the quantitative analysis of talcum powder spiked with perfume at different dosages. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Variable Thermal-Force Bending of a Three-Layer Bar with a Compressible Filler

NASA Astrophysics Data System (ADS)

Starovoitov, E. I.; Leonenko, D. V.

2017-11-01

Deformation of a three-layer elastoplastic bar with a compressible filler in a temperature field is considered. To describe the kinematics of a pack asymmetric across its thickness, the hypothesis of broken line is accepted, according to which the Bernoulli hypothesis is true in thin bearing layers, and the Timoshenko hypothesis is valid for a filler compressible across the its thickness, with a linear approximation of displacements across the layer thickness. The work of filler in the tangential direction is taken into account. The physical stress-strain relations correspond to the theory of small elastoplastic deformations. Temperature variations are calculated from a formula obtained by averaging the thermophysical properties of layer materials across the bar thickness. Using the variational method, a system of differential equilibrium equations is derived. On the boundary, the kinematic conditions of simply supported ends of the bar are assumed. The solution of the boundary problem is reduced to the search for four functions, namely, deflections and longitudinal displacements of median surfaces of the bearing layers. An analytical solution is derived by the method of elastic solutions with the use of the Moskvitin theorem on variable loadings. Its numerical analysis is performed for the cases of continuous and local loads.

Recycling and reuse of chosen kinds of waste materials in a building industry

NASA Astrophysics Data System (ADS)

Ferek, B.; Harasymiuk, J.; Tyburski, J.

2016-08-01

The article describes the current state of knowledge and practice in Poland concerning recycling as a method of reuse of chosen groups of waste materials in building industry. The recycling of building scraps is imposed by environmental, economic and technological premises. The issue of usage of sewage residues is becoming a problem of ever -growing gravity as the presence of the increasing number of pernicious contaminants makes their utilization for agricultural purposes more and more limited. The strategies of using waste materials on Polish building sites were analyzed. The analysis of predispositions to salvage for a group of traditional materials, such as: timber, steel, building debris, insulation materials, plastics, and on the example of new materials, such as: artificial light aggregates made by appropriate mixing of siliceous aggregates, glass refuses and sewage residues in order to obtain a commodity which is apt for economic usage also was made in the article. The issue of recycling of waste materials originating from building operations will be presented in the context of the binding home and EU legal regulations. It was proved that the level of recycling of building wastes in Poland is considerably different from one which is achieved in the solid market economies, both in quantity and in assortment. The method of neutralization of building refuses in connection with special waste materials, which are sewage sludge that is presented in the article may be one of the alternative solutions to the problem of recycling of these wastes not only on the Polish scale.

Automatic generation of user material subroutines for biomechanical growth analysis.

PubMed

Young, Jonathan M; Yao, Jiang; Ramasubramanian, Ashok; Taber, Larry A; Perucchio, Renato

2010-10-01

The analysis of the biomechanics of growth and remodeling in soft tissues requires the formulation of specialized pseudoelastic constitutive relations. The nonlinear finite element analysis package ABAQUS allows the user to implement such specialized material responses through the coding of a user material subroutine called UMAT. However, hand coding UMAT subroutines is a challenge even for simple pseudoelastic materials and requires substantial time to debug and test the code. To resolve this issue, we develop an automatic UMAT code generation procedure for pseudoelastic materials using the symbolic mathematics package MATHEMATICA and extend the UMAT generator to include continuum growth. The performance of the automatically coded UMAT is tested by simulating the stress-stretch response of a material defined by a Fung-orthotropic strain energy function, subject to uniaxial stretching, equibiaxial stretching, and simple shear in ABAQUS. The MATHEMATICA UMAT generator is then extended to include continuum growth by adding a growth subroutine to the automatically generated UMAT. The MATHEMATICA UMAT generator correctly derives the variables required in the UMAT code, quickly providing a ready-to-use UMAT. In turn, the UMAT accurately simulates the pseudoelastic response. In order to test the growth UMAT, we simulate the growth-based bending of a bilayered bar with differing fiber directions in a nongrowing passive layer. The anisotropic passive layer, being topologically tied to the growing isotropic layer, causes the bending bar to twist laterally. The results of simulations demonstrate the validity of the automatically coded UMAT, used in both standardized tests of hyperelastic materials and for a biomechanical growth analysis.

29 CFR 779.355 - Classification of lumber and building materials sales.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false Classification of lumber and building materials sales. 779... building materials sales. (a) General. In determining, for purposes of the section 13(a)(2) and (4) exemptions, whether 75 percent of the annual dollar volume of the establishment's sales which are not for...

29 CFR 779.355 - Classification of lumber and building materials sales.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Classification of lumber and building materials sales. 779... building materials sales. (a) General. In determining, for purposes of the section 13(a)(2) and (4) exemptions, whether 75 percent of the annual dollar volume of the establishment's sales which are not for...

Time Step Considerations when Simulating Dynamic Behavior of High Performance Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tabares-Velasco, Paulo Cesar

2016-09-01

Building energy simulations, especially those concerning pre-cooling strategies and cooling/heating peak demand management, require careful analysis and detailed understanding of building characteristics. Accurate modeling of the building thermal response and material properties for thermally massive walls or advanced materials like phase change materials (PCMs) are critically important.

Synthetic building materials for transport buildings and structures

NASA Astrophysics Data System (ADS)

Gerasimova, Vera

2017-10-01

The most effective building materials account for the highest growth not only in construction of residential and public buildings, but also other capital projects including roadways, bridges, drainage, communications and other engineering projects. Advancement in the technology of more efficient and ecologically responsible insulation materials have been a priority for safety, minimal maintenance and longevity of finished construction projects. The practical use of modern building materials such as insulation, sound reduction and low energy consumption are a benefit in cost and application compared to the use of outdated heavier and labor-intensive materials. The most efficient way for maximizing insolation and sound proofing should be done during the design stages of the project according to existing codes and regulations that are required by Western Government. All methods and materials that are used need to be optimized in order to reach a high durability and low operational and maintenance cost exceeding more than 50 years of the life of the building, whether it is for public, industrial or residential use. Western construction techniques and technologies need to be applied and adapted by the Russian Federation to insure the most productive successful methods are being implemented. The issues of efficient insulation materials are outlined in this article.

Seismic performance of circular reinforced concrete bridge columns constructed with grade 80 reinforcement.

DOT National Transportation Integrated Search

2014-08-01

This project assessed the use of ASTM A706 Grade 80 reinforcing bars in reinforced concrete columns. : Grade 80 is not currently allowed in reinforced concrete columns due to lack of information on the : material characteristics and column performanc...

Determination of steroid sex hormones in wastewater by stir bar sorptive extraction based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material and liquid chromatographic analysis.

PubMed

Huang, Xiaojia; Lin, Jianbin; Yuan, Dongxing; Hu, Rongzong

2009-04-17

In this study, a simple and rapid method was developed for the determination of seven steroid hormones in wastewater. Sample preparation and analysis were performed by stir bar sorptive extraction (SBSE) based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material (SBSEM) combined with high-performance liquid chromatography with diode array detection. To achieve the optimum extraction performance, several main parameters, including extraction and desorption time, pH value and contents of inorganic salt in the sample matrix, were investigated. Under the optimized experimental conditions, the method showed good linearity and repeatability, as well as advantages such as sensitivity, simplicity, low cost and high feasibility. The extraction performance of SBSEM to the target compounds also compared with commercial SBSE which used polydimethylsiloxane as coating. Finally, the proposed method was successfully applied to the determination of the target compounds in wastewater samples. The recoveries of spiked target compounds in real samples ranged from 48.2% to 110%.

Potential Explosion Hazard of Carbonaceous Nanoparticles: Screening of Allotropes

PubMed Central

Turkevich, Leonid A.; Fernback, Joseph; Dastidar, Ashok G.; Osterberg, Paul

2016-01-01

There is a concern that engineered carbon nanoparticles, when manufactured on an industrial scale, will pose an explosion hazard. Explosion testing has been performed on 20 codes of carbonaceous powders. These include several different codes of SWCNTs (single-walled carbon nanotubes), MWCNTs (multi-walled carbon nanotubes) and CNFs (carbon nanofibers), graphene, diamond, fullerene, as well as several different control carbon blacks and graphites. Explosion screening was performed in a 20 L explosion chamber (ASTM E1226 protocol), at a concentration of 500 g/m3, using a 5 kJ ignition source. Time traces of overpressure were recorded. Samples typically exhibited overpressures of 5–7 bar, and deflagration index KSt = V1/3 (dP/dt)max ~ 10 – 80 bar-m/s, which places these materials in European Dust Explosion Class St-1. There is minimal variation between these different materials. The explosive characteristics of these carbonaceous powders are uncorrelated with primary particle size (BET specific surface area). PMID:27468178

The potential of organic polymer-based hydrogen storage materials.

PubMed

Budd, Peter M; Butler, Anna; Selbie, James; Mahmood, Khalid; McKeown, Neil B; Ghanem, Bader; Msayib, Kadhum; Book, David; Walton, Allan

2007-04-21

The challenge of storing hydrogen at high volumetric and gravimetric density for automotive applications has prompted investigations into the potential of cryo-adsorption on the internal surface area of microporous organic polymers. A range of Polymers of Intrinsic Microporosity (PIMs) has been studied, the best PIM to date (a network-PIM incorporating a triptycene subunit) taking up 2.7% H(2) by mass at 10 bar/77 K. HyperCrosslinked Polymers (HCPs) also show promising performance as H(2) storage materials, particularly at pressures >10 bar. The N(2) and H(2) adsorption behaviour at 77 K of six PIMs and a HCP are compared. Surface areas based on Langmuir plots of H(2) adsorption at high pressure are shown to provide a useful guide to hydrogen capacity, but Langmuir plots based on low pressure data underestimate the potential H(2) uptake. The micropore distribution influences the form of the H(2) isotherm, a higher concentration of ultramicropores (pore size <0.7 nm) being associated with enhanced low pressure adsorption.

Performance of Metal and Polymeric O-Ring Seals during Beyond-Design-Basis Thermal Conditions.

PubMed

Yang, Jiann C; Hnetkovsky, Edward; Rinehart, Doris; Fernandez, Marco; Gonzalez, Felix; Borowsky, Joseph

2017-04-01

This paper summarizes the small scale thermal exposure test results of the performance of metallic and polymeric O-ring seals typically used in radioactive material transportation packages. Five different O-ring materials were evaluated: Inconel/silver, ethylene-propylene diene monomer (EPDM), polytetrafluoroethylene (PTFE), silicone, butyl, and Viton. The overall objective of this study is to provide test data and insights to the performance of these Oring seals when exposed to beyond-design-basis temperature conditions due to a severe fire. Tests were conducted using a small-scale stainless steel pressure vessel pressurized with helium to 2 bar or 5 bar at room temperature. The vessel was then heated in an electric furnace to temperatures up to 900 °C for a pre-determined period (typically 8 h to 9 h). The pressure drop technique was used to determine if leakage occurred during thermal exposure. Out of a total of 46 tests performed, leakage (loss of vessel pressure) was detected in 13 tests.

Vibrating membrane filtration as improved technology for microalgae dewatering.

PubMed

Nurra, Claudia; Clavero, Ester; Salvadó, Joan; Torras, Carles

2014-04-01

The effect of shear-enhanced filtration by vibratory process in microalgae dewatering is presented in this paper. The aim of this research was to investigate the technical performance and improvement of vibrating membrane filtration compared with conventional tangential cross-flow filtration in microalgae concentration. An industrial-scale available commercial set-up was used. Several membrane materials as polyethersulfone, polyacrylonitrile, etc., and mean pore sizes (from 7000Da to 0.2μm) were tested and compared in both filtration set-ups. Experiments were carried-out with Nannochloropsis gaditana and Phaeodactylum tricornutum microalgae. It has been demonstrated that, even if the choice of the membrane depends on its cut-off, its material and the type of microalgae filtrated, dynamic filtration is always the best technology over a conventional one. If with conventional filtration permeability values were in the vicinity of 10L/h/m(2)/bar in steady state phase, with dynamic filtration these values increased to 30L/h/m(2)/bar or more. Copyright © 2014 Elsevier Ltd. All rights reserved.

Performance of Metal and Polymeric O-Ring Seals during Beyond-Design-Basis Thermal Conditions*

PubMed Central

Yang, Jiann C.; Hnetkovsky, Edward; Rinehart, Doris; Fernandez, Marco; Gonzalez, Felix; Borowsky, Joseph

2017-01-01

This paper summarizes the small scale thermal exposure test results of the performance of metallic and polymeric O-ring seals typically used in radioactive material transportation packages. Five different O-ring materials were evaluated: Inconel/silver, ethylene-propylene diene monomer (EPDM), polytetrafluoroethylene (PTFE), silicone, butyl, and Viton. The overall objective of this study is to provide test data and insights to the performance of these Oring seals when exposed to beyond-design-basis temperature conditions due to a severe fire. Tests were conducted using a small-scale stainless steel pressure vessel pressurized with helium to 2 bar or 5 bar at room temperature. The vessel was then heated in an electric furnace to temperatures up to 900 °C for a pre-determined period (typically 8 h to 9 h). The pressure drop technique was used to determine if leakage occurred during thermal exposure. Out of a total of 46 tests performed, leakage (loss of vessel pressure) was detected in 13 tests. PMID:28503009

Research Progress of Building Materials Used in Construction Land

NASA Astrophysics Data System (ADS)

Niu, Yan

2018-01-01

Construction land preparation is an important aspect of land remediation project. The research of materials in the process of land improvement is the foundation and the core. Therefore, it is necessary to study the materials that may be involved in the process of building land preparation. In this paper, the research on the construction materials such as recycled concrete, geosynthetics, soil stabilizers, soil improvers, building insulation materials and inorganic fibrous insulation materials, which are commonly used in construction sites, is reviewed and discussed in this paper. Land remediation project involved in the construction of land materials to provide reference.

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Sales of building materials for residential or farm... for Certain Retail or Service Establishments Sales Not Made for Resale § 779.335 Sales of building... the category of sales for resale “the sale of goods to be used in residential or farm building...

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false Sales of building materials for residential or farm... for Certain Retail or Service Establishments Sales Not Made for Resale § 779.335 Sales of building... the category of sales for resale “the sale of goods to be used in residential or farm building...

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 3 2013-07-01 2013-07-01 false Sales of building materials for residential or farm... for Certain Retail or Service Establishments Sales Not Made for Resale § 779.335 Sales of building... the category of sales for resale “the sale of goods to be used in residential or farm building...

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 3 2014-07-01 2014-07-01 false Sales of building materials for residential or farm... for Certain Retail or Service Establishments Sales Not Made for Resale § 779.335 Sales of building... the category of sales for resale “the sale of goods to be used in residential or farm building...

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 3 2012-07-01 2012-07-01 false Sales of building materials for residential or farm... for Certain Retail or Service Establishments Sales Not Made for Resale § 779.335 Sales of building... the category of sales for resale “the sale of goods to be used in residential or farm building...

Directory of wood-framed building deconstruction and reused wood building materials companies, 2004

Treesearch

Robert H. Falk; G. Bradley Guy

2004-01-01

This is a directory of companies involved in wood-framed building deconstruction, dismantling and reused building materials, with an emphasis on those that use, resell, and/or re-manufacture salvaged wood. Companies in this directory range in scope from those that carryout targeted building removals, such as historic barns, strictly for the purpose of harvesting the...