Computer-based mechanical design of overhead lines

NASA Astrophysics Data System (ADS)

Rusinaru, D.; Bratu, C.; Dinu, R. C.; Manescu, L. G.

2016-02-01

Beside the performance, the safety level according to the actual standards is a compulsory condition for distribution grids’ operation. Some of the measures leading to improvement of the overhead lines reliability ask for installations’ modernization. The constraints imposed to the new lines components refer to the technical aspects as thermal stress or voltage drop, and look for economic efficiency, too. The mechanical sizing of the overhead lines is after all an optimization problem. More precisely, the task in designing of the overhead line profile is to size poles, cross-arms and stays and locate poles along a line route so that the total costs of the line's structure to be minimized and the technical and safety constraints to be fulfilled.The authors present in this paper an application for the Computer-Based Mechanical Design of the Overhead Lines and the features of the corresponding Visual Basic program, adjusted to the distribution lines. The constraints of the optimization problem are adjusted to the existing weather and loading conditions of Romania. The outputs of the software application for mechanical design of overhead lines are: the list of components chosen for the line: poles, cross-arms, stays; the list of conductor tension and forces for each pole, cross-arm and stay for different weather conditions; the line profile drawings.The main features of the mechanical overhead lines design software are interactivity, local optimization function and high-level user-interface

ExoMol line lists - XXII. The rotation-vibration spectrum of silane up to 1200 K

NASA Astrophysics Data System (ADS)

Owens, A.; Yachmenev, A.; Thiel, W.; Tennyson, J.; Yurchenko, S. N.

2017-11-01

A variationally computed 28SiH4 rotation-vibration line list applicable for temperatures up to T = 1200 K is presented. The line list, called OY2T, considers transitions with rotational excitation up to J = 42 in the wavenumber range 0-5000 cm-1 (wavelengths λ > 2 μm). Just under 62.7 billion transitions have been calculated between 6.1 million energy levels. Rovibrational calculations have utilized a new `spectroscopic' potential energy surface determined by empirical refinement to 1452 experimentally derived energy levels up to J = 6, and a previously reported ab initio dipole moment surface. The temperature-dependent partition function of silane, the OY2T line list format, and the temperature dependence of the OY2T line list are discussed. Comparisons with the PNNL spectral library and other experimental sources indicate that the OY2T line list is robust and able to accurately reproduce weaker intensity features. The full line list is available from the ExoMol data base and the CDS data base.

Quadrupole splittings in the near-infrared spectrum of 14NH 3

DOE PAGES

Twagirayezu, Sylvestre; Hall, Gregory E.; Sears, Trevor J.

2016-10-13

Sub-Doppler, saturation dip, spectra of lines in the v 1 + v 3, v 1 + 2v 4 and v 3 + 2v 4 bands of 14NH 3 have been measured by frequency comb-referenced diode laser absorption spectroscopy. The observed spectral line widths are dominated by transit time broadening, and show resolved or partially-resolved hyperfine splittings that are primarily determined by the 14N quadrupole coupling. Modeling of the observed line shapes based on the known hyperfine level structure of the ground state of the molecule shows that, in nearly all cases, the excited state level has hyperfine splittings similar tomore » the same rotational level in the ground state. The data provide accurate frequencies for the line positions and easily separate lines overlapped in Doppler-limited spectra. The observed hyperfine splittings can be used to make and confirm rotational assignments and ground state combination differences obtained from the measured frequencies are comparable in accuracy to those obtained from conventional microwave spectroscopy. Furthermore, several of the measured transitions do not show the quadrupole hyperfine splittings expected based on their existing rotational assignments. Either the assignments are incorrect or the upper levels involved are perturbed in a way that affects the nuclear hyperfine structure.« less

Lead

MedlinePlus

... Agendas, and Minutes New Blood Lead Level Information Funding Information Lead in Drinking Water Lead-based Water Lines Washington, D.C. Blood Lead Level Tests Effect of Previously Missing Blood Lead Level (BPb) Surveillance ...

Candy

MedlinePlus

... Agendas, and Minutes New Blood Lead Level Information Funding Information Lead in Drinking Water Lead-based Water Lines Washington, D.C. Blood Lead Level Tests Effect of Previously Missing Blood Lead Level (BPb) Surveillance ...

Water

MedlinePlus

... Agendas, and Minutes New Blood Lead Level Information Funding Information Lead in Drinking Water Lead-based Water Lines Washington, D.C. Blood Lead Level Tests Effect of Previously Missing Blood Lead Level (BPb) Surveillance ...

A coastal hazards data base for the U.S. West Coast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gornitz, V.M.; Beaty, T.W.; Daniels, R.C.

1997-12-01

This document describes the contents of a digital data base that may be used to identify coastlines along the US West Coast that are at risk to sea-level rise. This data base integrates point, line, and polygon data for the US West Coast into 0.25{degree} latitude by 0.25{degree} longitude grid cells and into 1:2,000,000 digitized line segments that can be used by raster or vector geographic information systems (GIS) as well as by non-GIS data bases. Each coastal grid cell and line segment contains data variables from the following seven data sets: elevation, geology, geomorphology, sea-level trends, shoreline displacement (erosion/accretion),more » tidal ranges, and wave heights. One variable from each data set was classified according to its susceptibility to sea-level rise and/or erosion to form 7 relative risk variables. These risk variables range in value from 1 to 5 and may be used to calculate a Coastal Vulnerability Index (CVI). Algorithms used to calculate several CVIs are listed within this text.« less

A new exact method for line radiative transfer

NASA Astrophysics Data System (ADS)

Elitzur, Moshe; Asensio Ramos, Andrés

2006-01-01

We present a new method, the coupled escape probability (CEP), for exact calculation of line emission from multi-level systems, solving only algebraic equations for the level populations. The CEP formulation of the classical two-level problem is a set of linear equations, and we uncover an exact analytic expression for the emission from two-level optically thick sources that holds as long as they are in the `effectively thin' regime. In a comparative study of a number of standard problems, the CEP method outperformed the leading line transfer methods by substantial margins. The algebraic equations employed by our new method are already incorporated in numerous codes based on the escape probability approximation. All that is required for an exact solution with these existing codes is to augment the expression for the escape probability with simple zone-coupling terms. As an application, we find that standard escape probability calculations generally produce the correct cooling emission by the CII 158-μm line but not by the 3P lines of OI.

Genomic vulnerability to LINE-1 hypomethylation is a potential determinant of the clinicogenetic features of multiple myeloma

PubMed Central

2012-01-01

Background The aim of this study was to clarify the role of global hypomethylation of repetitive elements in determining the genetic and clinical features of multiple myeloma (MM). Methods We assessed global methylation levels using four repetitive elements (long interspersed nuclear element-1 (LINE-1), Alu Ya5, Alu Yb8, and Satellite-α) in clinical samples comprising 74 MM samples and 11 benign control samples (7 cases of monoclonal gammopathy of undetermined significance (MGUS) and 4 samples of normal plasma cells (NPC)). We also evaluated copy-number alterations using array-based comparative genomic hybridization, and performed methyl-CpG binding domain sequencing (MBD-seq). Results Global levels of the repetitive-element methylation declined with the degree of malignancy of plasma cells (NPC>MGUS>MM), and there was a significant inverse correlation between the degree of genomic loss and the LINE-1 methylation levels. We identified 80 genomic loci as common breakpoints (CBPs) around commonly lost regions, which were significantly associated with increased LINE-1 densities. MBD-seq analysis revealed that average DNA-methylation levels at the CBP loci and relative methylation levels in regions with higher LINE-1 densities also declined during the development of MM. We confirmed that levels of methylation of the 5' untranslated region of respective LINE-1 loci correlated strongly with global LINE-1 methylation levels. Finally, there was a significant association between LINE-1 hypomethylation and poorer overall survival (hazard ratio 2.8, P = 0.015). Conclusion Global hypomethylation of LINE-1 is associated with the progression of and poorer prognosis for MM, possibly due to frequent copy-number loss. PMID:23259664

Setup for in situ deep level transient spectroscopy of semiconductors during swift heavy ion irradiation.

PubMed

Kumar, Sandeep; Kumar, Sugam; Katharria, Y S; Safvan, C P; Kanjilal, D

2008-05-01

A computerized system for in situ deep level characterization during irradiation in semiconductors has been set up and tested in the beam line for materials science studies of the 15 MV Pelletron accelerator at the Inter-University Accelerator Centre, New Delhi. This is a new facility for in situ irradiation-induced deep level studies, available in the beam line of an accelerator laboratory. It is based on the well-known deep level transient spectroscopy (DLTS) technique. High versatility for data manipulation is achieved through multifunction data acquisition card and LABVIEW. In situ DLTS studies of deep levels produced by impact of 100 MeV Si ions on Aun-Si(100) Schottky barrier diode are presented to illustrate performance of the automated DLTS facility in the beam line.

Revised energy levels of singly ionized lanthanum

NASA Astrophysics Data System (ADS)

Güzelçimen, Feyza; Tonka, Mehdi; Uddin, Zaheer; Bhatti, Naveed Anjum; Windholz, Laurentius; Kröger, Sophie; Başar, Gönül

2018-05-01

Based on the experimental wavenumbers of 344 spectral lines from calibrated Fourier transform (FT) spectra as well as wavenumbers of 81 lines from the wavelength tables from literature, the energy of 115 fine structure levels of singly ionized lanthanum has been revised by weighted global fits. The classifications of the lines are provided by numerous previous investigations of lanthanum by different spectroscopic methods and authors. For the high accurate determination of the center of gravity wavenumbers from the experimental spectrum, the hyperfine constants of the involved levels have been taken into account, if possible. For the 94 levels with known hyperfine constants the accuracy of energy values is better than 0.01 cm-1. For 34 levels the magnetic dipole hyperfine constants A have been determined from FT spectra as part of this work. For four of these 34 levels even electric quadrupole hyperfine constants B could be estimated. For levels, which have experimentally unknown hyperfine constants and which are connected only by lines not found in the FT spectra but taken from literature, the uncertainties of energy values are about a factor of 10 higher. A list of all revised level energies together with a compilation of hyperfine structure data is given as well as a list of all lines used.

Exploration of BEOL line-space patterning options at 12 nm half-pitch and below

NASA Astrophysics Data System (ADS)

Decoster, S.; Lazzarino, F.; Petersen Barbosa Lima, L.; Li, W.; Versluijs, J.; Halder, S.; Mallik, A.; Murdoch, G.

2018-03-01

While the semiconductor industry is almost ready for high-volume manufacturing of the 7 nm technology node, research centers are defining and troubleshooting the patterning options for the 5 nm technology node (N5) and below. The target dimension for imec's N5 BEOL applications is 20-24 nm Metal Pitch (MP), which requires Self-Aligned multiple (Double/Quadruple/Octuple) Patterning approaches (SAxP) in combination with EUV or immersion lithography at 193 nm. There are numerous technical challenges to enable gratings at the hard mask level such as good uniformity across wafer, low line edge/width roughness (LER/LWR), large process window, and all of this at low cost. An even greater challenge is to transfer these gratings into the dielectric material at such critical dimensions, where increased line edge roughness, line wiggling and even pattern collapse can be expected for materials with small mechanical stability such as highly porous low-k dielectrics. In this work we first compare three different patterning options for 12 nm half-pitch gratings at the hard mask level: EUV-based SADP and 193i-based SAQP and SAOP. This comparison will be based on process window, line edge/width roughness and cost. Next, the transfer of 12 nm line/space gratings in the dielectric material is discussed and presented. The LER of the dielectric lines is investigated as a function of the dielectric material, the trench depth, and the stress in the sacrificial hard mask. Finally, we elaborate on the different options to enable scaling down from 24 nm MP to 16 nm MP, and demonstrate 8 nm line/space gratings with 193i-based SAOP.

An experimental water line list at 1950 K in the 6250-6670 cm-1 region

NASA Astrophysics Data System (ADS)

Rutkowski, Lucile; Foltynowicz, Aleksandra; Schmidt, Florian M.; Johansson, Alexandra C.; Khodabakhsh, Amir; Kyuberis, Aleksandra A.; Zobov, Nikolai F.; Polyansky, Oleg L.; Yurchenko, Sergei N.; Tennyson, Jonathan

2018-01-01

An absorption spectrum of H216O at 1950 K is recorded in a premixed methane/air flat flame using a cavity-enhanced optical frequency comb-based Fourier transform spectrometer. 2417 absorption lines are identified in the 6250-6670 cm-1 region with an accuracy of about 0.01 cm-1. Absolute line intensities are retrieved using temperature and concentration values obtained by tunable diode laser absorption spectroscopy. Line assignments are made using a combination of empirically known energy levels and predictions from the new POKAZATEL variational line list. 2030 of the observed lines are assigned to 2937 transitions, once blends are taken into account. 126 new energy levels of H216O are identified. The assigned transitions belong to 136 bands and span rotational states up to J = 27 .

Ground cover changes resulting from low-level camping stress on a remote site

Treesearch

R. E. Leonard; J. M. McBride; P. W. Conkling; J. L. McMahon

1983-01-01

This study reports the effects of low-level camping stress on vegetation in a remote site. South Big Garden Island in Penobscot Bay, Maine, was studied because (1) it had no prior recreational use; thus, comprehensive base line data could be obtained; and (2) the exact number of campers could be monitored throughout the study period. The continuous line-intercept...

Analysis of differential protein expression in normal and neoplastic human breast epithelial cell lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, K.; Chubb, C.; Huberman, E.

High resolution two dimensional get electrophoresis (2DE) and database analysis was used to establish protein expression patterns for cultured normal human mammary epithelial cells and thirteen breast cancer cell lines. The Human Breast Epithelial Cell database contains the 2DE protein patterns, including relative protein abundances, for each cell line, plus a composite pattern that contains all the common and specifically expressed proteins from all the cell lines. Significant differences in protein expression, both qualitative and quantitative, were observed not only between normal cells and tumor cells, but also among the tumor cell lines. Eight percent of the consistently detected proteinsmore » were found in significantly (P < 0.001) variable levels among the cell lines. Using a combination of immunostaining, comigration with purified protein, subcellular fractionation, and amino-terminal protein sequencing, we identified a subset of the differentially expressed proteins. These identified proteins include the cytoskeletal proteins actin, tubulin, vimentin, and cytokeratins. The cell lines can be classified into four distinct groups based on their intermediate filament protein profile. We also identified heat shock proteins; hsp27, hsp60, and hsp70 varied in abundance and in some cases in the relative phosphorylation levels among the cell lines. Finally, we identified IMP dehydrogenase in each of the cell lines, and found the levels of this enzyme in the tumor cell lines elevated 2- to 20-fold relative to the levels in normal cells.« less

A Coastal Hazards Data Base for the U.S. West Coast (1997) (NDP-043C)

DOE Data Explorer

Gomitz, Vivien M. [Columbia Univ., New York, NY (United States); Beaty, Tammy W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Daniels, Richard C. [The University of Tennessee, Knoville, TN (United States)

1997-01-01

This data base integrates point, line, and polygon data for the U.S. West Coast into 0.25 degree latitude by 0.25 degree longitude grid cells and into 1:2,000,000 digitized line segments that can be used by raster or vector geographic information systems (GIS) as well as by non-GIS data bases. Each coastal grid cell and line segment contains data variables from the following seven data sets: elevation, geology, geomorphology, sea-level trends, shoreline displacement (erosion/accretion), tidal ranges, and wave heights. One variable from each data set was classified according to its susceptibility to sea-level rise and/or erosion to form 7 relative risk variables. These risk variables range in value from 1 to 5 and may be used to calculate a Coastal Vulnerability Index (CVI). Algorithms used to calculate several CVIs are listed within this text.

RADIATIVE TRANSFER MODELING OF THE ENIGMATIC SCATTERING POLARIZATION IN THE SOLAR Na i D{sub 1} LINE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belluzzi, Luca; Bueno, Javier Trujillo; Degl’Innocenti, Egidio Landi

2015-12-01

The modeling of the peculiar scattering polarization signals observed in some diagnostically important solar resonance lines requires the consideration of the detailed spectral structure of the incident radiation field as well as the possibility of ground level polarization, along with the atom's hyperfine structure and quantum interference between hyperfine F-levels pertaining either to the same fine structure J-level, or to different J-levels of the same term. Here we present a theoretical and numerical approach suitable for solving this complex non-LTE radiative transfer problem. This approach is based on the density-matrix metalevel theory (where each level is viewed as a continuousmore » distribution of sublevels) and on accurate formal solvers of the transfer equations and efficient iterative methods. We show an application to the D-lines of Na i, with emphasis on the enigmatic D{sub 1} line, pointing out the observable signatures of the various physical mechanisms considered. We demonstrate that the linear polarization observed in the core of the D{sub 1} line may be explained by the effect that one gets when the detailed spectral structure of the anisotropic radiation responsible for the optical pumping is taken into account. This physical ingredient is capable of introducing significant scattering polarization in the core of the Na i D{sub 1} line without the need for ground-level polarization.« less

A non-LTE treatment of beryllium lines - Misidentification of the solar Be I feature at 2650 A

NASA Technical Reports Server (NTRS)

Shipman, H. L.; Auer, L. H.

1979-01-01

The formation of beryllium lines, with particular reference to the solar Be spectrum, is investigated in a non-LTE context with a 25-level model atom in which 15 levels are allowed to depart from LTE. In some transitions, particularly the Be I 2650-A line, the non-LTE effects can be quite dramatic, changing the deduced abundances by a factor of 4. Based on the non-LTE calculations and Copernicus observations of other stars, it is found that a solar spectral feature at 2650 A, previously identified by numerous investigators as a Be I line, cannot be produced by Be I. Non-LTE effects on the Be II 3131-A line, used for most Be abundance determinations in the literature, are small by comparison.

Metabolomics Analysis of Hormone-Responsive and Triple-Negative Breast Cancer Cell Responses to Paclitaxel Identify Key Metabolic Differences.

PubMed

Stewart, Delisha A; Winnike, Jason H; McRitchie, Susan L; Clark, Robert F; Pathmasiri, Wimal W; Sumner, Susan J

2016-09-02

To date, no targeted therapies are available to treat triple negative breast cancer (TNBC), while other breast cancer subtypes are responsive to current therapeutic treatment. Metabolomics was conducted to reveal differences in two hormone receptor-negative TNBC cell lines and two hormone receptor-positive Luminal A cell lines. Studies were conducted in the presence and absence of paclitaxel (Taxol). TNBC cell lines had higher levels of amino acids, branched-chain amino acids, nucleotides, and nucleotide sugars and lower levels of proliferation-related metabolites like choline compared with Luminal A cell lines. In the presence of paclitaxel, each cell line showed unique metabolic responses, with some similarities by type. For example, in the Luminal A cell lines, levels of lactate and creatine decreased while certain choline metabolites and myo-inositol increased with paclitaxel. In the TNBC cell lines levels of glutamine, glutamate, and glutathione increased, whereas lysine, proline, and valine decreased in the presence of drug. Profiling secreted inflammatory cytokines in the conditioned media demonstrated a greater response to paclitaxel in the hormone-positive Luminal cells compared with a secretion profile that suggested greater drug resistance in the TNBC cells. The most significant differences distinguishing the cell types based on pathway enrichment analyses were related to amino acid, lipid and carbohydrate metabolism pathways, whereas several biological pathways were differentiated between the cell lines following treatment.

Detecting Inspection Objects of Power Line from Cable Inspection Robot LiDAR Data

PubMed Central

Qin, Xinyan; Wu, Gongping; Fan, Fei

2018-01-01

Power lines are extending to complex environments (e.g., lakes and forests), and the distribution of power lines in a tower is becoming complicated (e.g., multi-loop and multi-bundle). Additionally, power line inspection is becoming heavier and more difficult. Advanced LiDAR technology is increasingly being used to solve these difficulties. Based on precise cable inspection robot (CIR) LiDAR data and the distinctive position and orientation system (POS) data, we propose a novel methodology to detect inspection objects surrounding power lines. The proposed method mainly includes four steps: firstly, the original point cloud is divided into single-span data as a processing unit; secondly, the optimal elevation threshold is constructed to remove ground points without the existing filtering algorithm, improving data processing efficiency and extraction accuracy; thirdly, a single power line and its surrounding data can be respectively extracted by a structured partition based on a POS data (SPPD) algorithm from “layer” to “block” according to power line distribution; finally, a partition recognition method is proposed based on the distribution characteristics of inspection objects, highlighting the feature information and improving the recognition effect. The local neighborhood statistics and the 3D region growing method are used to recognize different inspection objects surrounding power lines in a partition. Three datasets were collected by two CIR LIDAR systems in our study. The experimental results demonstrate that an average 90.6% accuracy and average 98.2% precision at the point cloud level can be achieved. The successful extraction indicates that the proposed method is feasible and promising. Our study can be used to obtain precise dimensions of fittings for modeling, as well as automatic detection and location of security risks, so as to improve the intelligence level of power line inspection. PMID:29690560

Detecting Inspection Objects of Power Line from Cable Inspection Robot LiDAR Data.

PubMed

Qin, Xinyan; Wu, Gongping; Lei, Jin; Fan, Fei; Ye, Xuhui

2018-04-22

Power lines are extending to complex environments (e.g., lakes and forests), and the distribution of power lines in a tower is becoming complicated (e.g., multi-loop and multi-bundle). Additionally, power line inspection is becoming heavier and more difficult. Advanced LiDAR technology is increasingly being used to solve these difficulties. Based on precise cable inspection robot (CIR) LiDAR data and the distinctive position and orientation system (POS) data, we propose a novel methodology to detect inspection objects surrounding power lines. The proposed method mainly includes four steps: firstly, the original point cloud is divided into single-span data as a processing unit; secondly, the optimal elevation threshold is constructed to remove ground points without the existing filtering algorithm, improving data processing efficiency and extraction accuracy; thirdly, a single power line and its surrounding data can be respectively extracted by a structured partition based on a POS data (SPPD) algorithm from "layer" to "block" according to power line distribution; finally, a partition recognition method is proposed based on the distribution characteristics of inspection objects, highlighting the feature information and improving the recognition effect. The local neighborhood statistics and the 3D region growing method are used to recognize different inspection objects surrounding power lines in a partition. Three datasets were collected by two CIR LIDAR systems in our study. The experimental results demonstrate that an average 90.6% accuracy and average 98.2% precision at the point cloud level can be achieved. The successful extraction indicates that the proposed method is feasible and promising. Our study can be used to obtain precise dimensions of fittings for modeling, as well as automatic detection and location of security risks, so as to improve the intelligence level of power line inspection.

How Do High-Performance Work Systems Affect Individual Outcomes: A Multilevel Perspective.

PubMed

Zhang, Junwei; Akhtar, M Naseer; Bal, P Matthijs; Zhang, Yajun; Talat, Usman

2018-01-01

Research on high-performance work systems (HPWS) has suggested that a potential disconnection may exist between organizational-level HPWS and employee experienced HPWS. However, few studies have identified factors that are implied within such a relationship. Using a sample of 397 employees, 84 line managers, and 21 HR executives in China, we examined whether line managers' goal congruence can reduce the difference between organizational-level HPWS and employee experienced HPWS. Furthermore, this study also theorized and tested organization-based self-esteem (OBSE) as a mediator in the associations between employee experienced HPWS and job performance and job satisfaction. Using multilevel analyses, we found that line managers' goal congruence strengthened the relationship between organizational-level HPWS and employee experienced HPWS, such that the relationship was significant and positive when line managers' goal congruence was high, but a non-significant relationship when line managers' goal congruence was low. Moreover, employee experienced HPWS indirectly affected job performance and job satisfaction through the mechanism of OBSE beyond social exchange perspective.

How Do High-Performance Work Systems Affect Individual Outcomes: A Multilevel Perspective

PubMed Central

Zhang, Junwei; Akhtar, M. Naseer; Bal, P. Matthijs; Zhang, Yajun; Talat, Usman

2018-01-01

Research on high-performance work systems (HPWS) has suggested that a potential disconnection may exist between organizational-level HPWS and employee experienced HPWS. However, few studies have identified factors that are implied within such a relationship. Using a sample of 397 employees, 84 line managers, and 21 HR executives in China, we examined whether line managers’ goal congruence can reduce the difference between organizational-level HPWS and employee experienced HPWS. Furthermore, this study also theorized and tested organization-based self-esteem (OBSE) as a mediator in the associations between employee experienced HPWS and job performance and job satisfaction. Using multilevel analyses, we found that line managers’ goal congruence strengthened the relationship between organizational-level HPWS and employee experienced HPWS, such that the relationship was significant and positive when line managers’ goal congruence was high, but a non-significant relationship when line managers’ goal congruence was low. Moreover, employee experienced HPWS indirectly affected job performance and job satisfaction through the mechanism of OBSE beyond social exchange perspective. PMID:29743875

Does a Transformation Approach Improve Students' Ability in Constructing Auxiliary Lines for Solving Geometric Problems? An Intervention-Based Study with Two Chinese Classrooms

ERIC Educational Resources Information Center

Fan, Lianghuo; Qi, Chunxia; Liu, Xiaomei; Wang, Yi; Lin, Mengwei

2017-01-01

We conducted an intervention-based study in secondary classrooms to explore whether the use of geometric transformations can help improve students' ability in constructing auxiliary lines to solve geometric proof problems, especially high-level cognitive problems. A pre- and post-test quasi-experimental design was employed. The participants were…

A Comparison of Common and Novel Curriculum-Based Measurement of Reading Decision Rules to Predict Spring Performance for Students Receiving Supplemental Interventions

ERIC Educational Resources Information Center

Van Norman, Ethan R.; Parker, David C.

2018-01-01

Recent simulations suggest that trend line decision rules applied to curriculum-based measurement of reading progress monitoring data may lead to inaccurate interpretations unless data are collected for upward of 3 months. The authors of those studies did not manipulate goal line slope or account for a student's level of initial performance when…

Moral Stress, Moral Practice, and Ethical Climate in Community-Based Drug-Use Research: Views From the Front Line

PubMed Central

Fisher, Celia B.; True, Gala; Alexander, Leslie; Fried, Adam L.

2016-01-01

Background The role of front-line researchers, those whose responsibilities include face-to-face contact with participants, is critical to ensuring the responsible conduct of community-based drug use research. To date, there has been little empirical examination of how front-line researchers perceive the effectiveness of ethical procedures in their real-world application and the moral stress they may experience when adherence to scientific procedures appears to conflict with participant protections. Methods This study represents a first step in applying psychological science to examine the work-related attitudes, ethics climate, and moral dilemmas experienced by a national sample of 275 front-line staff members whose responsibilities include face-to-face interaction with participants in community-based drug-use research. Using an anonymous Web-based survey we psychometrically evaluated and examined relationships among six new scales tapping moral stress (frustration in response to perceived barriers to conducting research in a morally appropriate manner); organizational ethics climate; staff support; moral practice dilemmas (perceived conflicts between scientific integrity and participant welfare); research commitment; and research mistrust. Results As predicted, front-line researchers who evidence a strong commitment to their role in the research process and who perceive their organizations as committed to research ethics and staff support experienced lower levels of moral stress. Front-line researchers who were distrustful of the research enterprise and frequently grappled with moral practice dilemmas reported higher levels of moral stress. Conclusion Applying psychometrically reliable scales to empirically examine research ethics challenges can illuminate specific threats to scientific integrity and human subjects protections encountered by front-line staff and suggest organizational strategies for reducing moral stress and enhancing the responsible conduct of research. PMID:27795869

Moral Stress, Moral Practice, and Ethical Climate in Community-Based Drug-Use Research: Views From the Front Line.

PubMed

Fisher, Celia B; True, Gala; Alexander, Leslie; Fried, Adam L

2013-01-01

The role of front-line researchers, those whose responsibilities include face-to-face contact with participants, is critical to ensuring the responsible conduct of community-based drug use research. To date, there has been little empirical examination of how front-line researchers perceive the effectiveness of ethical procedures in their real-world application and the moral stress they may experience when adherence to scientific procedures appears to conflict with participant protections. This study represents a first step in applying psychological science to examine the work-related attitudes, ethics climate, and moral dilemmas experienced by a national sample of 275 front-line staff members whose responsibilities include face-to-face interaction with participants in community-based drug-use research. Using an anonymous Web-based survey we psychometrically evaluated and examined relationships among six new scales tapping moral stress (frustration in response to perceived barriers to conducting research in a morally appropriate manner); organizational ethics climate; staff support; moral practice dilemmas (perceived conflicts between scientific integrity and participant welfare); research commitment; and research mistrust. As predicted, front-line researchers who evidence a strong commitment to their role in the research process and who perceive their organizations as committed to research ethics and staff support experienced lower levels of moral stress. Front-line researchers who were distrustful of the research enterprise and frequently grappled with moral practice dilemmas reported higher levels of moral stress. Applying psychometrically reliable scales to empirically examine research ethics challenges can illuminate specific threats to scientific integrity and human subjects protections encountered by front-line staff and suggest organizational strategies for reducing moral stress and enhancing the responsible conduct of research.

Filtering of the Radon transform to enhance linear signal features via wavelet pyramid decomposition

NASA Astrophysics Data System (ADS)

Meckley, John R.

1995-09-01

The information content in many signal processing applications can be reduced to a set of linear features in a 2D signal transform. Examples include the narrowband lines in a spectrogram, ship wakes in a synthetic aperture radar image, and blood vessels in a medical computer-aided tomography scan. The line integrals that generate the values of the projections of the Radon transform can be characterized as a bank of matched filters for linear features. This localization of energy in the Radon transform for linear features can be exploited to enhance these features and to reduce noise by filtering the Radon transform with a filter explicitly designed to pass only linear features, and then reconstructing a new 2D signal by inverting the new filtered Radon transform (i.e., via filtered backprojection). Previously used methods for filtering the Radon transform include Fourier based filtering (a 2D elliptical Gaussian linear filter) and a nonlinear filter ((Radon xfrm)**y with y >= 2.0). Both of these techniques suffer from the mismatch of the filter response to the true functional form of the Radon transform of a line. The Radon transform of a line is not a point but is a function of the Radon variables (rho, theta) and the total line energy. This mismatch leads to artifacts in the reconstructed image and a reduction in achievable processing gain. The Radon transform for a line is computed as a function of angle and offset (rho, theta) and the line length. The 2D wavelet coefficients are then compared for the Haar wavelets and the Daubechies wavelets. These filter responses are used as frequency filters for the Radon transform. The filtering is performed on the wavelet pyramid decomposition of the Radon transform by detecting the most likely positions of lines in the transform and then by convolving the local area with the appropriate response and zeroing the pyramid coefficients outside of the response area. The response area is defined to contain 95% of the total wavelet coefficient energy. The detection algorithm provides an estimate of the line offset, orientation, and length that is then used to index the appropriate filter shape. Additional wavelet pyramid decomposition is performed in areas of high energy to refine the line position estimate. After filtering, the new Radon transform is generated by inverting the wavelet pyramid. The Radon transform is then inverted by filtered backprojection to produce the final 2D signal estimate with the enhanced linear features. The wavelet-based method is compared to both the Fourier and the nonlinear filtering with examples of sparse and dense shapes in imaging, acoustics and medical tomography with test images of noisy concentric lines, a real spectrogram of a blow fish (a very nonstationary spectrum), and the Shepp Logan Computer Tomography phantom image. Both qualitative and derived quantitative measures demonstrate the improvement of wavelet-based filtering. Additional research is suggested based on these results. Open questions include what level(s) to use for detection and filtering because multiple-level representations exist. The lower levels are smoother at reduced spatial resolution, while the higher levels provide better response to edges. Several examples are discussed based on analytical and phenomenological arguments.

MARVEL analysis of the rotational-vibrational states of the molecular ions H2D+ and D2H+.

PubMed

Furtenbacher, Tibor; Szidarovszky, Tamás; Fábri, Csaba; Császár, Attila G

2013-07-07

Critically evaluated rotational-vibrational line positions and energy levels, with associated critically reviewed labels and uncertainties, are reported for two deuterated isotopologues of the H3(+) molecular ion: H2D(+) and D2H(+). The procedure MARVEL, standing for Measured Active Rotational-Vibrational Energy Levels, is used to determine the validated levels and lines and their self-consistent uncertainties based on the experimentally available information. The spectral ranges covered for the isotopologues H2D(+) and D2H(+) are 5.2-7105.5 and 23.0-6581.1 cm(-1), respectively. The MARVEL energy levels of the ortho and para forms of the ions are checked against ones determined from accurate variational nuclear motion computations employing the best available adiabatic ab initio potential energy surfaces of these isotopologues. The number of critically evaluated, validated and recommended experimental (levels, lines) are (109, 185) and (104, 136) for H2D(+) and D2H(+), respectively. The lists of assigned MARVEL lines and levels and variational levels obtained for H2D(+) and D2H(+) as part of this study are deposited in the ESI to this paper.

Electronic multi-purpose material level sensor

DOEpatents

McEwan, T.E.

1997-03-11

The present electronic multi-purpose material level sensor is based on time domain reflectometry (TDR) of very short electrical pulses. Pulses are propagated along a transmission line that is partially immersed in a liquid, powder, or other substance such as grain in a silo. The time difference of the reflections at the start of the transmission line and the air/liquid interface are used to determine levels to better than 0.01 inch. The sensor is essentially independent of circuit element and temperature variations, and can be mass produced at an extremely low price. The transmission line may be a Goubau line, microstrip, coaxial cable, twin lead, CPS or CPW, and may typically be a strip placed along the inside wall of a tank. The reflected pulses also contain information about strata within the liquid such as sludge-build-up at the bottom of an oil tank. 9 figs.

Electronic multi-purpose material level sensor

DOEpatents

McEwan, Thomas E.

1997-01-01

The present electronic multi-purpose material level sensor is based on time domain reflectometry (TDR) of very short electrical pulses. Pulses are propagated along a transmission line that is partially immersed in a liquid, powder, or other substance such as grain in a silo. The time difference of the reflections at the start of the transmission line and the air/liquid interface are used to determine levels to better than 0.01 inch. The sensor is essentially independent of circuit element and temperature variations, and can be mass produced at an extremely low price. The transmission line may be a Goubau line, microstrip, coaxial cable, twin lead, CPS or CPW, and may typically be a strip placed along the inside wall of a tank. The reflected pulses also contain information about strata within the liquid such as sludge-build-up at the bottom of an oil tank.

Comparison of Highly Resolved Model-Based Exposure ...

EPA Pesticide Factsheets

Human exposure to air pollution in many studies is represented by ambient concentrations from space-time kriging of observed values. Space-time kriging techniques based on a limited number of ambient monitors may fail to capture the concentration from local sources. Further, because people spend more time indoors, using ambient concentration to represent exposure may cause error. To quantify the associated exposure error, we computed a series of six different hourly-based exposure metrics at 16,095 Census blocks of three Counties in North Carolina for CO, NOx, PM2.5, and elemental carbon (EC) during 2012. These metrics include ambient background concentration from space-time ordinary kriging (STOK), ambient on-road concentration from the Research LINE source dispersion model (R-LINE), a hybrid concentration combining STOK and R-LINE, and their associated indoor concentrations from an indoor infiltration mass balance model. Using a hybrid-based indoor concentration as the standard, the comparison showed that outdoor STOK metrics yielded large error at both population (67% to 93%) and individual level (average bias between −10% to 95%). For pollutants with significant contribution from on-road emission (EC and NOx), the on-road based indoor metric performs the best at the population level (error less than 52%). At the individual level, however, the STOK-based indoor concentration performs the best (average bias below 30%). For PM2.5, due to the relatively low co

Revised and extended analysis of the eighth spectrum of platinum (Pt VIII)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Azarov, Vladimir I., E-mail: vlad_azarov@yahoo.com; Gayasov, Robert R.

2017-05-15

The spectrum of platinum was observed in the 300–2100 Å wavelength region. Grazing and normal incidence VUV spectrographs have been used to record the spectrum. The (5d{sup 3}+5d{sup 2}6s)−5d{sup 2}6p transition array of seven times ionized platinum, Pt VIII, has been investigated. The configurations 5d{sup 3} and 5d{sup 2}6p had been previously studied, and all levels of these configurations (19 and 45 levels, respectively) had been established. The previous analysis was based on 178 classified spectral lines. In the current analysis we have confirmed identification of all previously found levels and all but 10 previously assigned spectral lines, although we havemore » detected a large (up to 35 mÅ) systematic shift in wavelength measurements used in the previous analysis. Based on new wavelength measurements, we have corrected the 5d{sup 3} and 5d{sup 2}6p energy level values (by up to 55 cm{sup −1}) and established for the first time 14 out of 16 theoretically possible 5d{sup 2}6s levels in Pt VIII. The total list of identified lines (including 180 new lines) contains 349 entries. The orthogonal operators technique was used to calculate the level structure and transition probabilities. The energy parameters have been determined by the least squares fit to the observed levels. Calculated transition probability and energy values, as well as LS-compositions obtained from the fitted parameters are presented.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Hoy, Blake W

The Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory (ORNL) provides variable energy neutrons for a variety of experiments. The neutrons proceed down beam lines to the experiment hall, which houses a variety of experiments and test articles. Each beam line has one or more neutron choppers which filter the neutron beam based on the neutron energy by using a rotating neutron absorbing material passing through the neutron beam. Excessive vibration of the Vision beam line, believed to be caused by the T0 chopper, prevented the Vision beam line from operating at full capacity. This problem had beenmore » addressed several times by rebalancing/reworking the T0 beam chopper but the problem stubbornly persisted. To determine the cause of the high vibration, dynamic testing was performed. Twenty-seven accelerometer and motor current channels of data were collected during drive up, drive down, coast down, and steady-state conditions; resonance testing and motor current signature analysis were also performed. The data was analyzed for traditional mechanical/machinery issues such as misalignment and imbalance using time series analysis, frequency domain analysis, and operating deflection shape analysis. The analysis showed that the chopper base plate was experiencing an amplified response to the excitation provided by the T0 beam chopper. The amplified response was diagnosed to be caused by higher than expected base plate flexibility, possibly due to improper grouting or loose floor anchors. Based on this diagnosis, a decision was made to dismantle the beam line chopper and remount the base plate. Neutron activation of the beam line components make modifications to the beam line especially expensive and time consuming due to the radiation handling requirements, so this decision had significant financial and schedule implications. It was found that the base plate was indeed loose because of improper grouting during its initial installation. The base plate was modified by splitting it into multiple sections, isolating the T0 chopper from the rest of the beam line, and each section was then reinstalled and re-grouted. After these modifications, the vibration levels were reduced by a factor of 30. The reduction in vibration level was sufficient to allow the Vision beam line to operate at full capacity for the first time since its completed construction date.« less

A lane line segmentation algorithm based on adaptive threshold and connected domain theory

NASA Astrophysics Data System (ADS)

Feng, Hui; Xu, Guo-sheng; Han, Yi; Liu, Yang

2018-04-01

Before detecting cracks and repairs on road lanes, it's necessary to eliminate the influence of lane lines on the recognition result in road lane images. Aiming at the problems caused by lane lines, an image segmentation algorithm based on adaptive threshold and connected domain is proposed. First, by analyzing features like grey level distribution and the illumination of the images, the algorithm uses Hough transform to divide the images into different sections and convert them into binary images separately. It then uses the connected domain theory to amend the outcome of segmentation, remove noises and fill the interior zone of lane lines. Experiments have proved that this method could eliminate the influence of illumination and lane line abrasion, removing noises thoroughly while maintaining high segmentation precision.

Soliton communication lines based on spectrally efficient modulation formats

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yushko, O V; Redyuk, A A

2014-06-30

We report the results of mathematical modelling of optical-signal propagation in soliton fibre-optic communication lines (FOCLs) based on spectrally efficient signal modulation formats. We have studied the influence of spontaneous emission noise, nonlinear distortions and FOCL length on the data transmission quality. We have compared the characteristics of a received optical signal for soliton and conventional dispersion compensating FOCLs. It is shown that in the presence of strong nonlinearity long-haul soliton FOCLs provide a higher data transmission performance, as well as allow higher order modulation formats to be used as compared to conventional communication lines. In the context of amore » coherent data transmission, soliton FOCLs allow the use of phase modulation with many levels, thereby increasing the spectral efficiency of the communication line. (optical communication lines)« less

Analysis of Student and School Level Variables Related to Mathematics Self-Efficacy Level Based on PISA 2012 Results for China-Shanghai, Turkey, and Greece

ERIC Educational Resources Information Center

Usta, H. Gonca

2016-01-01

This study aims to analyze the student and school level variables that affect students' self-efficacy levels in mathematics in China-Shanghai, Turkey, and Greece based on PISA 2012 results. In line with this purpose, the hierarchical linear regression model (HLM) was employed. The interschool variability is estimated at approximately 17% in…

A Demonstrator Intelligent Scheduler For Sensor-Based Robots

NASA Astrophysics Data System (ADS)

Perrotta, Gabriella; Allen, Charles R.; Shepherd, Andrew J.

1987-10-01

The development of an execution module capable of functioning as as on-line supervisor for a robot equipped with a vision sensor and tactile sensing gripper system is described. The on-line module is supported by two off-line software modules which provide a procedural based assembly constraints language to allow the assembly task to be defined. This input is then converted into a normalised and minimised form. The host Robot programming language permits high level motions to be issued at the to level, hence allowing a low programming overhead to the designer, who must describe the assembly sequence. Components are selected for pick and place robot movement, based on information derived from two cameras, one static and the other mounted on the end effector of the robot. The approach taken is multi-path scheduling as described by Fox pi. The system is seen to permit robot assembly in a less constrained parts presentation environment making full use of the sensory detail available on the robot.

Analysis of Subway Interior Noise at Peak Commuter Time.

PubMed

Lee, Donguk; Kim, Gibbeum; Han, Woojae

2017-07-01

Although mass transit systems are convenient and efficient for urban people, little attention has been paid to the potential hearing hazard from their noise. The purpose of the current study was to measure and analyze levels of subway interior noise at peak commuter times and to provide information about commuters' daily dose of noise exposure. To measure the subway interior noise, nine subway lines inside Seoul (i.e., lines 1-9) and six lines surrounding the capital city area (i.e., Central, Bundang, Sinbundang, Incheon, Gyeongui, and Gyeongchun) were chosen. The noise was measured and recorded by a sound level meter for two-hour periods in the morning and evening. 1) In the LZeq analysis, the average noise level of all 15 lines was 72.78 dB; the maximum and minimum noise levels were 78.34 and 62.46 dB, respectively. The average noise level of the nine lines inside Seoul was 73.45 dB, which was 1.68-dB louder than that of the six lines surrounding the capital city area. 2) Based on the LZeq analysis of 33 measured frequencies, 12.5 Hz was the highest frequency and 20,000 Hz was the lowest. 3) There was no remarkable difference in the level of subway interior noise between morning and evening peak commuter times. We concluded that the level of subway interior noise was not loud enough for commuters to incur noise-induced hearing loss. Regardless, environmental noise control efforts in the subway system might be needed for commuters who take a subway every day.

Anatomy-based image processing analysis of the running pattern of the perioral artery for minimally invasive surgery.

PubMed

Lee, Sang-Hee; Lee, Minho; Kim, Hee-Jin

2014-10-01

We aimed to elucidate the tortuous course of the perioral artery with the aid of image processing, and to suggest accurate reference points for minimally invasive surgery. We used 59 hemifaces from 19 Korean and 20 Thai cadavers. A perioral line was defined to connect the point at which the facial artery emerged on the mandibular margin, and the ramification point of the lateral nasal artery and the inferior alar branch. The course of the perioral artery was reproduced as a graph based on the perioral line and analysed by adding the image of the artery using MATLAB. The course of the artery could be classified into 2 according to the course of the alar branch - oblique and vertical. Two distinct inflection points appeared in the course of the artery along the perioral line at the ramification points of the alar branch and the inferior labial artery, respectively, and the course of the artery across the face can be predicted based on the following references: the perioral line, the ramification point of the alar branch (5∼10 mm medial to the perioral line at the level of the lower third of the upper lip) and the inferior labial artery (5∼10 mm medial to the perioral line at the level of the middle of the lower lip). Copyright © 2014 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Labady, N.; Özdalgiç, B.; Er, A.

The Fourier Transform spectra of a Holmium hollow cathode discharge lamp have been investigated in the UV spectral range from 25,000 up to 31,530 cm{sup −1} (317 to 400 nm). Two Ho spectra have been measured with neon and argon as buffer gases. Based on the intensity ratios from these two spectra, a distinction was made between atomic and ionic lines (ionic lines are discussed in an accompanying paper). Using the known Ho i energy levels, 71 lines could be classified as transitions of atomic Ho, 34 of which have not been published previously. Another 32 lines, which could notmore » be classified, are listed in the literature and assigned as atomic Ho. An additional 370 spectral lines have been assigned to atomic Ho based on the signal-to-noise ratio in the two spectra measured under different discharge conditions, namely with buffer gases argon and neon, respectively. These 370 lines have not been previously listed in the literature.« less

TrackCC: A Practical Wireless Indoor Localization System Based on Less-Expensive Chips

PubMed Central

Li, Xiaolong; Zheng, Yan; Cai, Jun; Yi, Yunfei

2017-01-01

This paper aims at proposing a new wireless indoor localization system (ILS), called TrackCC, based on a commercial type of low-power system-on-chip (SoC), nRF24LE1. This type of chip has only l output power levels and acute fluctuation for a received minimum power level in operation, which give rise to many practical challenges for designing localization algorithms. In order to address these challenges, we exploit the Markov theory to construct a (l+1)×(l+1) -sized state transition matrix to remove the fluctuation, and then propose a priority-based pattern matching algorithm to search for the most similar match in the signal map to estimate the real position of unknown nodes. The experimental results show that, compared to two existing wireless ILSs, LANDMARC and SAIL, which have meter level positioning accuracy, the proposed TrackCC can achieve the decimeter level accuracy on average in both line-of-sight (LOS) and non-line-of-sight (NLOS) senarios. PMID:28617313

Resident accuracy of joint line palpation using ultrasound verification.

PubMed

Rho, Monica E; Chu, Samuel K; Yang, Aaron; Hameed, Farah; Lin, Cindy Yuchin; Hurh, Peter J

2014-10-01

To determine the accuracy of knee and acromioclavicular (AC) joint line palpation in Physical Medicine and Rehabilitation (PM&R) residents using ultrasound (US) verification. Cohort study. PM&R residency program at an academic institution. Twenty-four PM&R residents participating in a musculoskeletal US course (7 PGY-2, 8 PGY-3, and 9 PGY4 residents). Twenty-four PM&R residents participating in an US course were asked to palpate the AC joint and lateral joint line of the knee in a female and male model before the start of the course. Once the presumed joint line was localized, the residents were asked to tape an 18-gauge, 1.5-inch, blunt-tip needle parallel to the joint line on the overlying skin. The accuracy of needle placement over the joint line was verified using US. US verification of correct needle placement over the joint line. Overall AC joint palpation accuracy was 16.7%, and knee lateral joint line palpation accuracy was 58.3%. Based on the resident level of education, using a value of P < .05, there were no statistically significant differences in the accuracy of joint line palpation. Residents in this study demonstrate poor accuracy of AC joint and lateral knee joint line identification by palpation, using US as the criterion standard for verification. There were no statistically significant differences in the accuracy rates of joint line palpation based on resident level of education. US may be a useful tool to use to advance the current methods of teaching the physical examination in medical education. Copyright © 2014 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

Improved results of LINE-1 methylation analysis in formalin-fixed, paraffin-embedded tissues with the application of a heating step during the DNA extraction process.

PubMed

Wen, Xianyu; Jeong, Seorin; Kim, Younghoon; Bae, Jeong Mo; Cho, Nam Yun; Kim, Jung Ho; Kang, Gyeong Hoon

2017-01-01

Formalin-fixed, paraffin-embedded (FFPE) tissues are important resources for profiling DNA methylation changes and for studying a variety of diseases. However, formalin fixation introduces inter-strand crosslinking, which might cause incomplete bisulfite conversion of unmethylated cytosines, which might lead to falsely elevated measurements of methylation levels in pyrosequencing assays. Long interspersed nucleotide element-1 (LINE-1) is a major constituent of repetitive transposable DNA elements, and its methylation is referred to correlates with global DNA methylation. To identify whether formalin fixation might impact the measured values of methylation in LINE-1 repetitive elements and whether prolonged heat-induced denaturation of DNA might reduce the artificial increases in measured values caused by formalin fixation, we analyzed paired fresh-frozen (FF) and FFPE xenograft tissue samples for their methylation levels in LINE-1 using a pyrosequencing assay. To further confirm the effect of a heating step in the measurement of LINE-1 or single gene methylation levels, we analyzed FFPE tissue samples of gastric cancer and colorectal cancer for their methylation status in LINE-1 and eight single genes, respectively. Formalin fixation led to an increase in the measured values of LINE-1 methylation regardless of the duration of fixation. Prolonged heating of the DNA at 95 °C for 30 min before bisulfite conversion was found (1) to decrease the discrepancy in the measured values between the paired FF and FFPE tissue samples, (2) to decrease the standard deviation of the measured value of LINE-1 methylation levels in FFPE tissue samples of gastric cancer, and (3) to improve the performance in the measurement of single gene methylation levels in FFPE tissue samples of colorectal cancer. Formalin fixation leads to artificial increases in the measured values of LINE-1 methylation, and the application of prolonged heating of DNA samples decreases the discrepancy in the measured values of LINE-1 methylation between paired FF and FFPE tissue samples. The application of prolonged heating of DNA samples improves bisulfite conversion-based measurement of LINE-1 or single gene methylation levels in FFPE tissue samples.

ExoMol molecular line lists - XXVI: spectra of SH and NS

NASA Astrophysics Data System (ADS)

Yurchenko, Sergei N.; Bond, Wesley; Gorman, Maire N.; Lodi, Lorenzo; McKemmish, Laura K.; Nunn, William; Shah, Rohan; Tennyson, Jonathan

2018-07-01

Line lists for the sulphur-containing molecules SH (the mercapto radical) and NS are computed as part of the ExoMol project. These line lists consider transitions within the X2Π ground state for 32SH, 33SH, 34SH,36SH and, 32SD, and 14N32S, 14N33S, 14N34S, 14N36S, and 15N32S. Ab initio potential energy (PEC) and spin-orbit coupling (SOC) curves are computed and then improved by fitting to experimentally observed transitions. Fully ab initio dipole moment curves (DMCs) computed at high level of theory are used to produce the final line lists. For SH, our fit gives a root-mean-square (rms) error of 0.03 cm-1 between the observed (vmax = 4, Jmax = 34.5) and calculated transitions wavenumbers; this is extrapolated such that all X2Π rotational-vibrational-electronic (rovibronic) bound states are considered. For 32SH the resulting line list contains about 81 000 transitions and 2300 rovibronic states, considering levels up to vmax = 14 and Jmax = 60.5. For NS the refinement used a combination of experimentally determined frequencies and energy levels and led to an rms-fitting error of 0.002 cm-1. Each NS-calculated line list includes around 2.8 million transitions and 31 000 rovibronic states with a vibrational range up to v = 53 and rotational range up to J = 235.5, which covers up to 23 000 cm-1. Both line lists should be complete for temperatures up to 5000 K. Example spectra simulated using this line list are shown and comparisons made to the existing data in the CDMS data base. The line lists are available from the CDS (http://cdsarc.u-strasbg.fr) and ExoMol (www.exomol.com) data bases.

Theme-Based Courses Foster Student Learning and Promote Comfort with Learning New Material

ERIC Educational Resources Information Center

Tessier, Lisa; Tessier, Jack

2015-01-01

In this article, we review the literature about theme-based teaching, then report quantitative and qualitative results from surveys from three different courses: one section of a 100-level in-person art course; five sections of 300-level on-line art courses; and one section of a 100-level in-person biology course at SUNY Delhi with applied themes…

An Accurate Potential Energy Surface for H2O

NASA Technical Reports Server (NTRS)

Schwenke, David W.; Partridge, Harry; Langhoff, Stephen R. (Technical Monitor)

1997-01-01

We have carried out extensive high quality ab initio electronic structure calculations of the ground state potential energy surface (PES) and dipole moment function (DMF) for H2O. A small adjustment is made to the PES to improve the agreement of line positions from theory and experiment. The theoretical line positions are obtained from variational ro-vibrational calculations using the exact kinetic energy operator. For the lines being fitted, the root-mean-square error was reduced from 6.9 to 0.08 /cm. We were then able to match 30,092 of the 30,117 lines from the HITRAN 96 data base to theoretical lines, and 80% of the line positions differed less than 0.1 /cm. About 3% of the line positions in the experimental data base appear to be incorrect. Theory predicts the existence of many additional weak lines with intensities above the cutoff used in the data base. To obtain results of similar accuracy for HDO, a mass dependent correction to the PH is introduced and is parameterized by simultaneously fitting line positions for HDO and D2O. The mass dependent PH has good predictive value for T2O and HTO. Nonadiabatic effects are not explicitly included. Line strengths for vibrational bands summed over rotational levels usually agree well between theory and experiment, but individual line strengths can differ greatly. A high temperature line list containing about 380 million lines has been generated using the present PES and DMF

TS and ERCC-1 mRNA expressions and clinical outcome in patients with metastatic colon cancer in CONFIRM-1 and -2 clinical trials.

PubMed

Grimminger, P P; Shi, M; Barrett, C; Lebwohl, D; Danenberg, K D; Brabender, J; Vigen, C L P; Danenberg, P V; Winder, T; Lenz, H-J

2012-10-01

To validate established cutoff levels of thymidylate synthase (TS) and excision repair cross-complementing (ERCC-1) intratumoral mRNA expressions in tumor samples from metastatic colorectal cancer (mCRC) patients treated with PTK787/ZK222584 (PTK/ZK). From 122 samples of patients with mCRC enrolled in CONFIRM-1 (Colorectal Oral Novel Therapy for the Inhibition of Angiogenesis and Retarding of Metastases) or CONFIRM-2, mRNA was isolated of microdissected formalin-fixed paraffin-embedded samples and quantitated using TaqMan-based technology. Existing TS and ERCC-1 cutoff levels were tested for their prognostic value in first-line and second-line therapy. TS expression was associated with overall survival (OS) in first-line, but not second-line therapy. ERCC-1 was associated with OS in patients treated with first-line and second-line FOLFOX4. In first-line FOLFOX4, combination of high TS and/or high ERCC-1 was associated with shorter OS. A correlation was observed between ERCC-1 expression and benefit from PTK/ZK+FOLFOX4 treatment. TS and ERCC-1 expression is associated with clinical outcome in mCRC. Baseline TS and ERCC-1 levels may allow the selection of patients who benefit from FOLFOX4 chemotherapy.

Line Identification of Atomic and Ionic Spectra of Holmium in the Near-UV. Part I. Spectrum of Ho I

NASA Astrophysics Data System (ADS)

Al-Labady, N.; Özdalgiç, B.; Er, A.; Güzelçimen, F.; Öztürk, I. K.; Kröger, S.; Kruzins, A.; Tamanis, M.; Ferber, R.; Başar, Gö.

2017-02-01

The Fourier Transform spectra of a Holmium hollow cathode discharge lamp have been investigated in the UV spectral range from 25,000 up to 31,530 cm-1 (317 to 400 nm). Two Ho spectra have been measured with neon and argon as buffer gases. Based on the intensity ratios from these two spectra, a distinction was made between atomic and ionic lines (ionic lines are discussed in an accompanying paper). Using the known Ho I energy levels, 71 lines could be classified as transitions of atomic Ho, 34 of which have not been published previously. Another 32 lines, which could not be classified, are listed in the literature and assigned as atomic Ho. An additional 370 spectral lines have been assigned to atomic Ho based on the signal-to-noise ratio in the two spectra measured under different discharge conditions, namely with buffer gases argon and neon, respectively. These 370 lines have not been previously listed in the literature.

Research and application on imaging technology of line structure light based on confocal microscopy

NASA Astrophysics Data System (ADS)

Han, Wenfeng; Xiao, Zexin; Wang, Xiaofen

2009-11-01

In 2005, the theory of line structure light confocal microscopy was put forward firstly in China by Xingyu Gao and Zexin Xiao in the Institute of Opt-mechatronics of Guilin University of Electronic Technology. Though the lateral resolution of line confocal microscopy can only reach or approach the level of the traditional dot confocal microscopy. But compared with traditional dot confocal microscopy, it has two advantages: first, by substituting line scanning for dot scanning, plane imaging only performs one-dimensional scanning, with imaging velocity greatly improved and scanning mechanism simplified, second, transfer quantity of light is greatly improved by substituting detection hairline for detection pinhole, and low illumination CCD is used directly to collect images instead of photoelectric intensifier. In order to apply the line confocal microscopy to practical system, based on the further research on the theory of the line confocal microscopy, imaging technology of line structure light is put forward on condition of implementation of confocal microscopy. Its validity and reliability are also verified by experiments.

Ab initio non-adiabatic study of the 4pσ B'' 1Σ+u state of H2

NASA Astrophysics Data System (ADS)

Glass-Maujean, M.; Schmoranzer, H.

2018-05-01

Fully ab initio non-adiabatic multichannel quantum defect calculations of the 4pσ B'' 1∑u+ energy levels, line intensities and widths, based on the latest quantum-chemical clamped-nuclei calculations of Wolniewicz and collaborators are presented for H2. The B″ state corresponds to the inner well of the ? state. The B'' v ≥ 1 levels are rapidly predissociated through vibrational coupling with the 3pσ B' 1Σ+u continuum so that coupled-equation calculations become unstable. Multichannel quantum defect theory, on the other hand, is demonstrated to be particularly suited to this situation. Experimental data as level energies, line intensities and dissociation widths were revisited and corrected. Reinvestigating previously published spectra, several new lines were assigned.

Analysis of Electrowetting Dynamics with Level Set Method

NASA Astrophysics Data System (ADS)

Park, Jun Kwon; Hong, Jiwoo; Kang, Kwan Hyoung

2009-11-01

Electrowetting is a versatile tool to handle tiny droplets and forms a backbone of digital microfluidics. Numerical analysis is necessary to fully understand the dynamics of electrowetting, especially in designing electrowetting-based liquid lenses and reflective displays. We developed a numerical method to analyze the general contact-line problems, incorporating dynamic contact angle models. The method was applied to the analysis of spreading process of a sessile droplet for step input voltages in electrowetting. The result was compared with experimental data and analytical result which is based on the spectral method. It is shown that contact line friction significantly affects the contact line motion and the oscillation amplitude. The pinning process of contact line was well represented by including the hysteresis effect in the contact angle models.

STATCONT: A statistical continuum level determination method for line-rich sources

NASA Astrophysics Data System (ADS)

Sánchez-Monge, Á.; Schilke, P.; Ginsburg, A.; Cesaroni, R.; Schmiedeke, A.

2018-01-01

STATCONT is a python-based tool designed to determine the continuum emission level in spectral data, in particular for sources with a line-rich spectrum. The tool inspects the intensity distribution of a given spectrum and automatically determines the continuum level by using different statistical approaches. The different methods included in STATCONT are tested against synthetic data. We conclude that the sigma-clipping algorithm provides the most accurate continuum level determination, together with information on the uncertainty in its determination. This uncertainty can be used to correct the final continuum emission level, resulting in the here called `corrected sigma-clipping method' or c-SCM. The c-SCM has been tested against more than 750 different synthetic spectra reproducing typical conditions found towards astronomical sources. The continuum level is determined with a discrepancy of less than 1% in 50% of the cases, and less than 5% in 90% of the cases, provided at least 10% of the channels are line free. The main products of STATCONT are the continuum emission level, together with a conservative value of its uncertainty, and datacubes containing only spectral line emission, i.e., continuum-subtracted datacubes. STATCONT also includes the option to estimate the spectral index, when different files covering different frequency ranges are provided.

Electricity Breakdown Management for Sarawak Energy: Use of Condition-Based Equipment for Detection of Defective Insulator

NASA Astrophysics Data System (ADS)

Tan, J. K.; Abas, N.

2017-07-01

Managing electricity breakdown is vital since an outage causes economic losses for customers and the utility companies. However, electricity breakdown is unavoidable due to some internal or external factors beyond our control. Electricity breakdown on overhead lines tend occur more frequently because it is prone to external disturbances such as animal, overgrown vegetation and defective pole top accessories. In Sarawak Energy Berhad (SEB), majority of the network are composed of overhead lines and hence, is more prone to failure. Conventional method of equipment inspection and fault finding are not effective to quickly identify the root cause of failure. SEB has engaged the use of corona discharge camera as condition-based monitoring equipment to carry out condition based inspection on the line in order to diagnose the condition of the lines prior to failure. Experimental testing has been carried out to determine the correlation between the corona discharge count and the level of defect on line insulator. The result shall be tabulated and will be used as reference for future scanning and diagnostic on any defect on the lines.

Line Assignments and Position Measurements in Several Weak CO2 Bands Between 4590/cm and 7930/cm

NASA Technical Reports Server (NTRS)

Giver, L. P.; Kshirsagar, R. J.; Freedman, R. C.; Chackerian, C., Jr.; Wattson, R. B.; Gore, Warren J. (Technical Monitor)

1998-01-01

A substantial set of CO2 spectra from 4500 to 12000/cm has been obtained at Ames with 1500 m path length using a Bomem DA8 FTS. The signal/noise was improved compared to prior spectra obtained in this laboratory by including a filter wheel limiting the band-pass of each spectrum to several hundred per cm. We have measured positions of lines in several weak bands not previously resolved in laboratory spectra. Using our positions and assignments of lines of the Qbranch of the 31103-00001 vibrational band at 4591/cm, we have redetermined the rotational constants for the 31103f levels. Q-branch lines of this band were previously observed, but misassigned, in Venus spectra by Mandin. The current HITRAN values of the rotational constants for this level are incorrect due to the Q-branch misassignments. Our prior measurements of the 21122-00001 vibrational band at 7901/cm were limited to Q-and R-branch lines; with the improved signal/noise of these new spectra we have now measured lines in the weaker P branch. The 21122 (Gv = 790148/cm) levels are known to be perturbed by the 32211 (G(sub v) = 789757/cm) levels; new DND calculations predict that high-J lines of the forbidden 32211-00001 vibrational band 'borrow' intensity from the corresponding transitions of the 21122-00001 band. We have identified such Q- and R-branch transitions of the 32211-00001 band from 26 < J" < 44, based on our position measurements of lines in the 32211-02201 band at 6562/cm.

A perceptive method for handwritten text segmentation

NASA Astrophysics Data System (ADS)

Lemaitre, Aurélie; Camillerapp, Jean; Coüasnon, Bertrand

2011-01-01

This paper presents a new method to address the problem of handwritten text segmentation into text lines and words. Thus, we propose a method based on the cooperation among points of view that enables the localization of the text lines in a low resolution image, and then to associate the pixels at a higher level of resolution. Thanks to the combination of levels of vision, we can detect overlapping characters and re-segment the connected components during the analysis. Then, we propose a segmentation of lines into words based on the cooperation among digital data and symbolic knowledge. The digital data are obtained from distances inside a Delaunay graph, which gives a precise distance between connected components, at the pixel level. We introduce structural rules in order to take into account some generic knowledge about the organization of a text page. This cooperation among information gives a bigger power of expression and ensures the global coherence of the recognition. We validate this work using the metrics and the database proposed for the segmentation contest of ICDAR 2009. Thus, we show that our method obtains very interesting results, compared to the other methods of the literature. More precisely, we are able to deal with slope and curvature, overlapping text lines and varied kinds of writings, which are the main difficulties met by the other methods.

Intraoperative fluorescence-based enhanced reality laparoscopic real-time imaging to assess bowel perfusion at the anastomotic site in an experimental model.

PubMed

Diana, M; Agnus, V; Halvax, P; Liu, Y-Y; Dallemagne, B; Schlagowski, A-I; Geny, B; Diemunsch, P; Lindner, V; Marescaux, J

2015-01-01

Fluorescence videography is a promising technique for assessing bowel perfusion. Fluorescence-based enhanced reality (FLER) is a novel concept, in which a dynamic perfusion cartogram, generated by computer analysis, is superimposed on to real-time laparoscopic images. The aim of this experimental study was to assess the accuracy of FLER in detecting differences in perfusion in a small bowel resection-anastomosis model. A small bowel ischaemic segment was created laparoscopically in 13 pigs. Animals were allocated to having anastomoses performed at either low perfusion (25 per cent; n = 7) or high perfusion (75 per cent; n = 6), as determined by FLER analysis. Capillary lactate levels were measured in blood samples obtained by serosal puncturing in the ischaemic area, resection lines and vascularized areas. Pathological inflammation scoring of the anastomosis was carried out. Lactate levels in the ischaemic area (mean(s.d.) 5·6(2·8) mmol/l) were higher than those in resection lines at 25 per cent perfusion (3·7(1·7) mmol/l; P = 0·010) and 75 per cent perfusion (2·9(1·3) mmol/l; P < 0·001), and higher than levels in vascular zones (2·5(1·0) mmol/l; P < 0·001). Lactate levels in resection lines with 75 per cent perfusion were lower than those in lines with 25 per cent perfusion (P < 0·001), and similar to those in vascular zones (P = 0·188). Levels at resection lines with 25 per cent perfusion were higher than those in vascular zones (P = 0·001). Mean(s.d.) global inflammation scores were higher in the 25 per cent perfusion group compared with the 75 per cent perfusion group for mucosa/submucosa (2·1(0·4) versus 1·2(0·4); P = 0·003) and serosa (1·8(0·4) versus 0·8(0·8); P = 0·014). A ratio of preanastomotic lactate levels in the ischaemic area relative to the resection lines of 2 or less was predictive of a more severe inflammation score. In an experimental model, FLER appeared accurate in discriminating bowel perfusion levels. Surgical relevance Clinical assessment has limited accuracy in evaluating bowel perfusion before anastomosis. Fluorescence videography estimates intestinal perfusion based on the fluorescence intensity of injected fluorophores, which is proportional to bowel vascularization. However, evaluation of fluorescence intensity remains a static and subjective measure. Fluorescence-based enhanced reality (FLER) is a dynamic fluorescence videography technique integrating near-infrared endoscopy and specific software. The software generates a virtual perfusion cartogram based on time to peak fluorescence, which can be superimposed on to real-time laparoscopic images. This experimental study demonstrates the accuracy of FLER in detecting differences in bowel perfusion in a survival model of laparoscopic small bowel resection-anastomosis, based on biochemical and histopathological data. It is concluded that real-time imaging of bowel perfusion is easy to use and accurate, and should be translated into clinical use. © 2015 BJS Society Ltd. Published by John Wiley & Sons Ltd.

Automatic Line Network Extraction from Aerial Imagery of Urban Areas through Knowledge-Based Image Analysis.

DTIC Science & Technology

1988-01-19

approach for the analysis of aerial images. In this approach image analysis is performed ast three levels of abstraction, namely iconic or low-level... image analysis , symbolic or medium-level image analysis , and semantic or high-level image analysis . Domain dependent knowledge about prototypical urban

Analysis of Subway Interior Noise at Peak Commuter Time

PubMed Central

Lee, Donguk; Kim, Gibbeum; Han, Woojae

2017-01-01

Background and Objectives Although mass transit systems are convenient and efficient for urban people, little attention has been paid to the potential hearing hazard from their noise. The purpose of the current study was to measure and analyze levels of subway interior noise at peak commuter times and to provide information about commuters’ daily dose of noise exposure. Materials and Methods To measure the subway interior noise, nine subway lines inside Seoul (i.e., lines 1-9) and six lines surrounding the capital city area (i.e., Central, Bundang, Sinbundang, Incheon, Gyeongui, and Gyeongchun) were chosen. The noise was measured and recorded by a sound level meter for two-hour periods in the morning and evening. Results 1) In the LZeq analysis, the average noise level of all 15 lines was 72.78 dB; the maximum and minimum noise levels were 78.34 and 62.46 dB, respectively. The average noise level of the nine lines inside Seoul was 73.45 dB, which was 1.68-dB louder than that of the six lines surrounding the capital city area. 2) Based on the LZeq analysis of 33 measured frequencies, 12.5 Hz was the highest frequency and 20,000 Hz was the lowest. 3) There was no remarkable difference in the level of subway interior noise between morning and evening peak commuter times. Conclusions We concluded that the level of subway interior noise was not loud enough for commuters to incur noise-induced hearing loss. Regardless, environmental noise control efforts in the subway system might be needed for commuters who take a subway every day. PMID:28704890

Monitoring Intracellular Oxygen Concentration: Implications for Hypoxia Studies and Real-Time Oxygen Monitoring.

PubMed

Potter, Michelle; Badder, Luned; Hoade, Yvette; Johnston, Iain G; Morten, Karl J

2016-01-01

The metabolic properties of cancer cells have been widely accepted as a hallmark of cancer for a number of years and have shown to be of critical importance in tumour development. It is generally accepted that tumour cells exhibit a more glycolytic phenotype than normal cells. In this study, we investigate the bioenergetic phenotype of two widely used cancer cell lines, RD and U87MG, by monitoring intracellular oxygen concentrations using phosphorescent Pt-porphyrin based intracellular probes. Our study demonstrates that cancer cell lines do not always exhibit an exclusively glycolytic phenotype. RD demonstrates a reliance on oxidative phosphorylation whilst U87MG display a more glycolytic phenotype. Using the intracellular oxygen sensing probe we generate an immediate readout of intracellular oxygen levels, with the glycolytic lines reflecting the oxygen concentration of the environment, and cells with an oxidative phenotype having significantly lower levels of intracellular oxygen. Inhibition of oxygen consumption in lines with high oxygen consumption increases intracellular oxygen levels towards environmental levels. We conclude that the use of intracellular oxygen probes provides a quantitative assessment of intracellular oxygen levels, allowing the manipulation of cellular bioenergetics to be studied in real time.

Line pilot perspectives on complexity of terminal instrument flight procedures

DOT National Transportation Integrated Search

2017-07-25

Instrument flight procedures (IFPs) based on RNAV and RNP offer safety enhancements along with new levels of flexibility to negotiate terrain, airspace, and environmental considerations. However, operational implementation of performance-based IFPs d...

Line integral on engineering mathematics

NASA Astrophysics Data System (ADS)

Wiryanto, L. H.

2018-01-01

Definite integral is a basic material in studying mathematics. At the level of calculus, calculating of definite integral is based on fundamental theorem of calculus, related to anti-derivative, as the inverse operation of derivative. At the higher level such as engineering mathematics, the definite integral is used as one of the calculating tools of line integral. the purpose of this is to identify if there is a question related to line integral, we can use definite integral as one of the calculating experience. The conclusion of this research says that the teaching experience in introducing the relation between both integrals through the engineer way of thinking can motivate and improve students in understanding the material.

High-level cross-resistance to didanosine observed in South African children failing an abacavir- or stavudine-based 1st-line regimen.

PubMed

Steegen, Kim; Levin, Leon; Ketseoglou, Irene; Bronze, Michelle; Papathanasopoulos, Maria A; Carmona, Sergio; Stevens, Wendy

2014-01-01

The knowledge-base of emerging drug resistance profiles in children exposed to abacavir-based antiretroviral regimens in South Africa is very limited. This study investigated the suitability of didanosine-based 2nd-line regimens for children in the context of antiretroviral drug resistance patterns emerging after 1st-line virologic failure. A retrospective dataset of 354 antiretroviral drug resistant genotypes from children failing either abacavir (n = 81) or stavudine (n = 273) based 1st-line regimens, was analysed. Samples were sent to the HIV genotyping laboratory at Charlotte Maxeke Johannesburg Academic Hospital, for routine testing. Pol sequences were submitted to the Stanford HIV drug resistance database for genotypic predictions. Children were exposed to abacavir or stavudine-based 1st-line regimens for an average of 21 and 36 months, respectively. The frequency of reduced susceptibility to didanosine was substantial in the abacavir-exposed group (69.1%).This reduced susceptibility was commonly attributed to L74V/I (n = 44) and to a lesser extent K65R (n = 10) mutations. Didanosine resistance was observed in 43.2% of patients exposed to stavudine-based regimens. In contrast, most children remained susceptible to stavudine regardless of exposure to abacavir (77.8%) or stavudine (74.7%). At least 80% of children remained susceptible to zidovudine irrespective of stavudine or abacavir-exposure. The presence of the K65R mutation was more common after abacavir pressure (12.3% vs 1.8%). Analysis revealed that didanosine-based 2nd-line regimens have limitations for South African children, given the high frequency of mutations that confer cross-resistance to didanosine; especially after abacavir-exposure. This data has influenced South African paediatric treatment guidelines, which now recommend zidovudine-based 2nd-line regimens.

Genetic characterization of Russian honey bee stock selected for improved resistance to Varroa destructor.

PubMed

Bourgeois, A Lelania; Rinderer, Thomas E

2009-06-01

Maintenance of genetic diversity among breeding lines is important in selective breeding and stock management. The Russian Honey Bee Breeding Program has strived to maintain high levels of heterozygosity among its breeding lines since its inception in 1997. After numerous rounds of selection for resistance to tracheal and varroa mites and improved honey production, 18 lines were selected as the core of the program. These lines were grouped into three breeding blocks that were crossbred to improve overall heterozygosity levels of the population. Microsatellite DNA data demonstrated that the program has been successful. Heterozygosity and allelic richness values are high and there are no indications of inbreeding among the three blocks. There were significant levels of genetic structure measured among the three blocks. Block C was genetically distinct from both blocks A and B (F(ST) = 0.0238), whereas blocks A and B did not differ from each other (F(ST) = 0.0074). The same pattern was seen for genic (based on numbers of alleles) differentiation. Genetic distance, as measured by chord distance, indicates that all of the 18 lines are equally distant, with minimal clustering. The data indicate that the overall design of the breeding program has been successful in maintaining high levels of diversity and avoiding problems associated with inbreeding.

POLARIZED LINE FORMATION WITH LOWER-LEVEL POLARIZATION AND PARTIAL FREQUENCY REDISTRIBUTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Supriya, H. D.; Sampoorna, M.; Nagendra, K. N.

2016-09-10

In the well-established theories of polarized line formation with partial frequency redistribution (PRD) for a two-level and two-term atom, it is generally assumed that the lower level of the scattering transition is unpolarized. However, the existence of unexplained spectral features in some lines of the Second Solar Spectrum points toward a need to relax this assumption. There exists a density matrix theory that accounts for the polarization of all the atomic levels, but it is based on the flat-spectrum approximation (corresponding to complete frequency redistribution). In the present paper we propose a numerical algorithm to solve the problem of polarizedmore » line formation in magnetized media, which includes both the effects of PRD and the lower level polarization (LLP) for a two-level atom. First we derive a collisionless redistribution matrix that includes the combined effects of the PRD and the LLP. We then solve the relevant transfer equation using a two-stage approach. For illustration purposes, we consider two case studies in the non-magnetic regime, namely, the J {sub a} = 1, J {sub b} = 0 and J {sub a} = J {sub b} = 1, where J {sub a} and J {sub b} represent the total angular momentum quantum numbers of the lower and upper states, respectively. Our studies show that the effects of LLP are significant only in the line core. This leads us to propose a simplified numerical approach to solve the concerned radiative transfer problem.« less

Cancer biomarker discovery is improved by accounting for variability in general levels of drug sensitivity in pre-clinical models.

PubMed

Geeleher, Paul; Cox, Nancy J; Huang, R Stephanie

2016-09-21

We show that variability in general levels of drug sensitivity in pre-clinical cancer models confounds biomarker discovery. However, using a very large panel of cell lines, each treated with many drugs, we could estimate a general level of sensitivity to all drugs in each cell line. By conditioning on this variable, biomarkers were identified that were more likely to be effective in clinical trials than those identified using a conventional uncorrected approach. We find that differences in general levels of drug sensitivity are driven by biologically relevant processes. We developed a gene expression based method that can be used to correct for this confounder in future studies.

A cross-sectional study to evaluate second line virological failure and elevated bilirubin as a surrogate for adherence to atazanavir/ritonavir in two urban HIV clinics in Lilongwe, Malawi.

PubMed

Ongubo, Dennis Miyoge; Lim, Robertino; Tweya, Hannock; Stanley, Christopher Chikhosi; Tembo, Petros; Broadhurst, Richard; Gugsa, Salem; Ngongondo, McNeil; Speight, Colin; Heller, Tom; Phiri, Sam; Hosseinipour, Mina C

2017-07-03

Malawi's national antiretroviral therapy program provides atazanavir/ritonavir-based second line regimens which cause concentration-dependent rise in indirect bilirubin. We sought to determine if elevated bilirubin, as a surrogate of atazanavir/ritonavir adherence, can aid in the evaluation of second line virological failure in Malawi. We conducted a cross-sectional study of HIV-infected patients ≥15 years who were on boosted protease inhibitor-based second line antiretroviral therapy for at least 6 months in two urban HIV clinics in Lilongwe, Malawi. Antiretroviral therapy history and adherence data were extracted from the electronic medical records and blood was drawn for viral load, complete blood count, total bilirubin, and CD4 cell count at a clinic visit. Factors associated with virological failure were assessed using multivariate logistic regression model. Out of 376 patients on second line antiretroviral therapy evaluated, 372 (98.9%) were on atazanavir/ritonavir-based therapy and 142 (37.8%) were male. Mean age was 40.9 years (SD ± 10.1), mean duration on second line antiretroviral therapy was 41.9 months (SD ± 27.6) and 256 patients (68.1%) had elevated bilirubin >1.3 mg/dL. Overall, 35 (9.3%) patients had viral load >1000 copies/ml (virological failure). Among the virologically failing vs. non-failing patients, bilirubin was elevated in 34.3% vs. 72.0% respectively (p < 0.001), although adherence by pill count was similar (62.9% vs. 60.7%, p = 0.804). The odds of virological failure were higher for adults aged 25-40 years (adjusted odds ratio (aOR) 2.5, p = 0.048), those with CD4 cell count <100 (aOR 17.5, p < 0.001), and those with normal bilirubin levels (aOR 5.4, p < 0.001); but were lower for the overweight/obese patients (aOR 0.3, p = 0.026). Poor pill count adherence (aOR 0.7, p = 0.4) and male gender (aOR 1.2, p = 0.698) were not associated with second line virological failure. Among patients receiving atazanavir/ritonavir-based second line antiretroviral therapy, bilirubin levels better predicted virological failure than pill count adherence. Therefore, strategic use of bilirubin and viral load testing to target adherence counseling and support may be cost-effective in monitoring second line antiretroviral therapy adherence and virological failure. Drug resistance testing targeted for patients with virological failure despite elevated bilirubin levels would facilitate timely switch to third line antiretroviral regimens whenever available.

Electronics Curriculum.

ERIC Educational Resources Information Center

Prickett, Charlotte

This document presents results of research conducted by industry representatives regarding tasks performed by electronic technicians and line manufacturing electro-mechanical technicians in Arizona electronics industries. Based on this research, a competency-based curriculum was developed for training entry-level electronics technicians. Twelve…

Modeling the size-density relationship in direct-seeded slash pine stands

Treesearch

Quang V. Cao; Thomas J. Dean; V. Clark Baldwin

2000-01-01

The relationship between quadratic mean diameter and tree density appeared curvilinear on a log–log scale, based on data from direct-seeded slash pine (Pinus elliotti var. elliotti Engelm.) stands. The self-thinning trajectory followed a straight line for high tree density levels and then turned away from this line as tree density...

First-line eradication for Helicobacter pylori-positive gastritis by esomeprazole-based triple therapy is influenced by CYP2C19 genotype

PubMed Central

Saito, Yoshimasa; Serizawa, Hiroshi; Kato, Yukako; Nakano, Masaru; Nakamura, Masahiko; Saito, Hidetsugu; Suzuki, Hidekazu; Kanai, Takanori

2015-01-01

AIM: To evaluate the effect of first line esomeprazole (EPZ)-based triple therapy on Helicobacter pylori (H. pylori) eradication. METHODS: A total of 80 Japanese patients with gastritis who were diagnosed as positive for H. pylori infection by endoscopic biopsy-based or 13C-urea breath tests were included in this study. The average age of the patients was 57.2 years (male/female, 42/38). These patients were treated by first-line eradication therapy with EPZ 40 mg/d, amoxicillin 1500 mg/d, and clarithromycin 400 mg/d for 7 d. All drugs were given twice per day. Correlations between H. pylori eradication, CYP2C19 genotype, and serum pepsinogen (PG) level were analyzed. This study was registered with the UMIN Clinical Trials Registry (UMIN000009642). RESULTS: The H. pylori eradication rates by EPZ-based triple therapy evaluated by intention-to-treat and per protocol were 67.5% and 68.4%, respectively, which were similar to triple therapies with other first-generation proton pump inhibitors (PPIs). The eradication rates in three different CYP2C19 genotypes, described as extensive metabolizer (EM), intermediate metabolizer, and poor metabolizer, were 52.2%, 72.1%, and 84.6%, respectively. The H. pylori eradication rate was significantly lower in EM than non-EM (P < 0.05). The serum PG I level and PG I/II ratio were significantly increased after eradication of H. pylori (P < 0.01), suggesting that gastric atrophy was improved by H. pylori eradication. Thus, first-line eradication by EPZ-based triple therapy for patients with H. pylori-positive gastritis was influenced by CYP2C19 genotype, and the eradication rate was on the same level with other first-generation PPIs in the Japanese population. CONCLUSION: The results from this study suggest that there is no advantage to EPZ-based triple therapy on H. pylori eradication compared to other first-generation PPIs. PMID:26730167

Line drawing extraction from gray level images by feature integration

NASA Astrophysics Data System (ADS)

Yoo, Hoi J.; Crevier, Daniel; Lepage, Richard; Myler, Harley R.

1994-10-01

We describe procedures that extract line drawings from digitized gray level images, without use of domain knowledge, by modeling preattentive and perceptual organization functions of the human visual system. First, edge points are identified by standard low-level processing, based on the Canny edge operator. Edge points are then linked into single-pixel thick straight- line segments and circular arcs: this operation serves to both filter out isolated and highly irregular segments, and to lump the remaining points into a smaller number of structures for manipulation by later stages of processing. The next stages consist in linking the segments into a set of closed boundaries, which is the system's definition of a line drawing. According to the principles of Gestalt psychology, closure allows us to organize the world by filling in the gaps in a visual stimulation so as to perceive whole objects instead of disjoint parts. To achieve such closure, the system selects particular features or combinations of features by methods akin to those of preattentive processing in humans: features include gaps, pairs of straight or curved parallel lines, L- and T-junctions, pairs of symmetrical lines, and the orientation and length of single lines. These preattentive features are grouped into higher-level structures according to the principles of proximity, similarity, closure, symmetry, and feature conjunction. Achieving closure may require supplying missing segments linking contour concavities. Choices are made between competing structures on the basis of their overall compliance with the principles of closure and symmetry. Results include clean line drawings of curvilinear manufactured objects. The procedures described are part of a system called VITREO (viewpoint-independent 3-D recognition and extraction of objects).

Saturated fluorescence method for determination of atomic transition probabilities: Application to the Ar i 430.0-nm (1s4-3p8) transition and the lifetime determination of the upper level

NASA Astrophysics Data System (ADS)

Hirabayashi, A.; Okuda, S.; Nambu, Y.; Fujimoto, T.

1987-01-01

We have developed a new method for determination of atomic transition probabilities based on laser-induced-fluorescence spectroscopy (LIFS). In the method one produces a known population of atoms in the upper level under investigation and relates it to an observed absolute line intensity. We have applied this method to the argon 430.0-nm line (1s4-3p8): In an argon discharge plasma the 1s5-level population and spatial distribution are determined by the self-absorption method combined with LIFS under conditions where the 3p8-level population is much lower than that of the 1s5 level. When intense laser light of 419.1 nm (1s5-3p8) irradiates the plasma and saturates the 3p8-level population, the produced 3p8-level population and its alignment can be determined from the 1s5-level parameters as determined above, by solving the master equation on the basis of broad-line excitation. By comparing the observed absolute fluorescence intensity of the 430.0-nm line with the above population, we have determined the transition probability to be A=(3.94+/-0.60)×105 s-1. We also determined the 3p8-level lifetime by LIFS. Several factors which might affect the measurement are discussed. The result is τ=127+/-10 ns.

Radiation characteristics and polarisation of undulated microstrip line antennas

NASA Astrophysics Data System (ADS)

Shafai, L.; Sebak, A. A.

1985-12-01

A numerical method is used to investigate the radiation from undulated microstrip line antennas. The undulated line is assumed to be suspended over a ground plane and its current distribution is determined using a moment method type solution. This current distribution is then used to compute the co-polar and cross-polar radiation fields. It is found that the current distribution has an oscillating behavior along the line, with a frequency which is twice the number of undulations. The cross-polarization is found to be high and relatively independent of the undulating shape. Its relative level, however, is reduced for large arrays, due to the array factor affecting the co-polar field. A procedure for the reduction or elimination of the cross-polarization is then proposed, which is based on utilizing two undulated lines with mutually inverted undulations. A design method for achieving low sidelobe levels is also proposed and a design example with sidelobes around the -40 dB range is presented.

Biphasic adaptation to osmotic stress in the C. elegans germ line.

PubMed

Davis, Michael; Montalbano, Andrea; Wood, Megan P; Schisa, Jennifer A

2017-06-01

Cells respond to environmental stress in multiple ways. In the germ line, heat shock and nutritive stress trigger the assembly of large ribonucleoprotein (RNP) granules via liquid-liquid phase separation (LLPS). The RNP granules are hypothesized to maintain the quality of oocytes during stress. The goal of this study was to investigate the cellular response to glucose in the germ line and determine if it is an osmotic stress response. We found that exposure to 500 mM glucose induces the assembly of RNP granules in the germ line within 1 h. Interestingly, the RNP granules are maintained for up to 3 h; however, they dissociate after longer periods of stress. The RNP granules include processing body and stress granule proteins, suggesting shared functions. Based on several lines of evidence, the germ line response to glucose largely appears to be an osmotic stress response, thus identifying osmotic stress as a trigger of LLPS. Although RNP granules are not maintained beyond 3 h of osmotic stress, the quality of oocytes does not appear to decrease after longer periods of stress, suggesting a secondary adaptation in the germ line. We used an indirect marker of glycerol and observed high levels after 5 and 20 h of glucose exposure. Moreover, in gpdh-1;gpdh-2 germ lines, glycerol levels are reduced concomitant with RNP granules being maintained for an extended period. We speculate that increased glycerol levels may function as a secondary osmoregulatory adaptive response in the germ line, following a primary response of RNP granule assembly. Copyright © 2017 the American Physiological Society.

DETAIL VIEW ON THE MAIN ASSEMBLY LEVEL OF ELEVATOR SHOWING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW ON THE MAIN ASSEMBLY LEVEL OF ELEVATOR SHOWING THE DOUBLED COLUMN FOR THE BUILDING EXPANSION JOINT AT COLUMN LINE AA-18. - Offutt Air Force Base, Glenn L. Martin-Nebraska Bomber Plant, Building D, Peacekeeper Drive, Bellevue, Sarpy County, NE

Genetic variation and population structure of maize inbred lines adapted to the mid-altitude sub-humid maize agro-ecology of Ethiopia using single nucleotide polymorphic (SNP) markers.

PubMed

Ertiro, Berhanu Tadesse; Semagn, Kassa; Das, Biswanath; Olsen, Michael; Labuschagne, Maryke; Worku, Mosisa; Wegary, Dagne; Azmach, Girum; Ogugo, Veronica; Keno, Tolera; Abebe, Beyene; Chibsa, Temesgen; Menkir, Abebe

2017-10-12

Molecular characterization is important for efficient utilization of germplasm and development of improved varieties. In the present study, we investigated the genetic purity, relatedness and population structure of 265 maize inbred lines from the Ethiopian Institute of Agricultural Research (EIAR), the International Maize and Wheat Improvement Centre (CIMMYT) and the International Institute of Tropical Agriculture (IITA) using 220,878 single nucleotide polymorphic (SNP) markers obtained using genotyping by sequencing (GBS). Only 22% of the inbred lines were considered pure with <5% heterogeneity, while the remaining 78% of the inbred lines had a heterogeneity ranging from 5.1 to 31.5%. Pairwise genetic distances among the 265 inbred lines varied from 0.011 to 0.345, with 89% of the pairs falling between 0.301 and 0.345. Only <1% of the pairs had a genetic distance lower than 0.200, which included 14 pairs of sister lines that were nearly identical. Relative kinship analysis showed that the kinship coefficients for 59% of the pairs of lines was close to zero, which agrees with the genetic distance estimates. Principal coordinate analysis, discriminant analysis of principal components (DAPC) and the model-based population structure analysis consistently suggested the presence of three groups, which generally agreed with pedigree information (genetic background). Although not distinct enough, the SNP markers showed some level of separation between the two CIMMYT heterotic groups A and B established based on pedigree and combining ability information. The high level of heterogeneity detected in most of the inbred lines suggested the requirement for purification or further inbreeding except those deliberately maintained at early inbreeding level. The genetic distance and relative kinship analysis clearly indicated the uniqueness of most of the inbred lines in the maize germplasm available for breeders in the mid-altitude maize breeding program of Ethiopia. Results from the present study facilitate the maize breeding work in Ethiopia and germplasm exchange among breeding programs in Africa. We suggest the incorporation of high density molecular marker information in future heterotic group assignments.

RNA deep sequencing as a tool for selection of cell lines for systematic subcellular localization of all human proteins.

PubMed

Danielsson, Frida; Wiking, Mikaela; Mahdessian, Diana; Skogs, Marie; Ait Blal, Hammou; Hjelmare, Martin; Stadler, Charlotte; Uhlén, Mathias; Lundberg, Emma

2013-01-04

One of the major challenges of a chromosome-centric proteome project is to explore in a systematic manner the potential proteins identified from the chromosomal genome sequence, but not yet characterized on a protein level. Here, we describe the use of RNA deep sequencing to screen human cell lines for RNA profiles and to use this information to select cell lines suitable for characterization of the corresponding gene product. In this manner, the subcellular localization of proteins can be analyzed systematically using antibody-based confocal microscopy. We demonstrate the usefulness of selecting cell lines with high expression levels of RNA transcripts to increase the likelihood of high quality immunofluorescence staining and subsequent successful subcellular localization of the corresponding protein. The results show a path to combine transcriptomics with affinity proteomics to characterize the proteins in a gene- or chromosome-centric manner.

X-ray line ratios from helium-like ions - Updated theory and SMM flare observations

NASA Technical Reports Server (NTRS)

Wolfson, C. J.; Leibacher, J. W.; Doyle, J. G.; Phillips, K. J. H.

1983-01-01

The potential which the conduction of measurements of the three principal lines emitted from helium-like ions has for the determination of plasma electron density was initially pointed out by Gabriel and Jordan (1969). The diagnostic technique is based on the fact that the ratio, R, of the intensity of a forbidden line to the intensity of an intercombination line decreases as electron density increases due to collisional excitation of levels. In the present investigation a further refinement of this procedure is provided by specifically calculating the effects of cascades from levels with principal quantum numbers up to n=6. Two improved spectrometers recently placed in operation include the SOLEX instrument on the satellite P78-1 and the X-ray Polychromator (XRP) instrument on the NASA Solar Maximum Mission satellite. Measurements obtained with one of the spectrometers making up the XRP are presented, taking into account the emission from Ne IX ions.

X-ray line ratios from helium-like ions - Updated theory and SMM flare observations

NASA Astrophysics Data System (ADS)

Wolfson, C. J.; Leibacher, J. W.; Doyle, J. G.; Phillips, K. J. H.

1983-06-01

The potential which the conduction of measurements of the three principal lines emitted from helium-like ions has for the determination of plasma electron density was initially pointed out by Gabriel and Jordan (1969). The diagnostic technique is based on the fact that the ratio, R, of the intensity of a forbidden line to the intensity of an intercombination line decreases as electron density increases due to collisional excitation of levels. In the present investigation a further refinement of this procedure is provided by specifically calculating the effects of cascades from levels with principal quantum numbers up to n=6. Two improved spectrometers recently placed in operation include the SOLEX instrument on the satellite P78-1 and the X-ray Polychromator (XRP) instrument on the NASA Solar Maximum Mission satellite. Measurements obtained with one of the spectrometers making up the XRP are presented, taking into account the emission from Ne IX ions.

Investigation of the tone-burst tube for duct lining attenuation measurement

NASA Technical Reports Server (NTRS)

Soffel, A. R.; Morrow, P. F.

1972-01-01

The tone burst technique makes practical the laboratory evaluation of potential inlet and discharge duct treatments. Tone burst apparatus requires only simple machined parts and standard components. Small, simply made, lining samples are quickly and easily installed in the system. Two small electromagnetric loudspeaker drivers produce peak sound pressure level of over 166 db in the 3-square-inch sample duct. Air pump available in most laboratories can produce air flows of over plus and minus Mach 0.3 in the sample duct. The technique uses short shaped pulses of sound propagated down a progressive wave tube containing the sample duct. The peak pressure level output of the treated duct is compared with the peak pressure level output of a substituted reference duct. The difference between the levels is the attenuation or insertion loss of the treated duct. Evaluations of resonant absorber linings by the tone burst technique check attenuation values predicted by empirical formulas based on full scale ducts.

A level-set method for two-phase flows with moving contact line and insoluble surfactant

NASA Astrophysics Data System (ADS)

Xu, Jian-Jun; Ren, Weiqing

2014-04-01

A level-set method for two-phase flows with moving contact line and insoluble surfactant is presented. The mathematical model consists of the Navier-Stokes equation for the flow field, a convection-diffusion equation for the surfactant concentration, together with the Navier boundary condition and a condition for the dynamic contact angle derived by Ren et al. (2010) [37]. The numerical method is based on the level-set continuum surface force method for two-phase flows with surfactant developed by Xu et al. (2012) [54] with some cautious treatment for the boundary conditions. The numerical method consists of three components: a flow solver for the velocity field, a solver for the surfactant concentration, and a solver for the level-set function. In the flow solver, the surface force is dealt with using the continuum surface force model. The unbalanced Young stress at the moving contact line is incorporated into the Navier boundary condition. A convergence study of the numerical method and a parametric study are presented. The influence of surfactant on the dynamics of the moving contact line is illustrated using examples. The capability of the level-set method to handle complex geometries is demonstrated by simulating a pendant drop detaching from a wall under gravity.

Standardized, Interdepartmental, Simulation-Based Central Line Insertion Course Closes an Educational Gap and Improves Intern Comfort with the Procedure.

PubMed

Grudziak, Joanna; Herndon, Blair; Dancel, Ria D; Arora, Harendra; Tignanelli, Christopher J; Phillips, Michael R; Crowner, Jason R; True, Nicholas A; Kiser, Andy C; Brown, Rebecca F; Goodell, Harry P; Murty, Neil; Meyers, Michael O; Montgomery, Sean P

2017-06-01

Central line placement is a common procedure, routinely performed by junior residents in medical and surgical departments. Before this project, no standardized instructional course on the insertion of central lines existed at our institution, and few interns had received formal ultrasound training. Interns from five departments participated in a simulation-based central line insertion course. Intern familiarity with the procedure and with ultrasound, as well as their prior experience with line placement and their level of comfort, was assessed. Of the 99 interns in participating departments, 45 per cent had been trained as of October 2015. Forty-one per cent were female. The majority (59.5%) had no prior formal ultrasound training, and 46.0 per cent had never placed a line as primary operator. Scores increased significantly, from a precourse score mean of 13.7 to a postcourse score mean of 16.1, P < 0.001. All three of the self-reported measures of comfort with ultrasound also improved significantly. All interns reported the course was "very much" helpful, and 100 per cent reported they felt "somewhat" or "much" more comfortable with the procedure after attendance. To our knowledge, this is the first hospital-wide, standardized, simulation-based central line insertion course in the United States. Preliminary results indicate overwhelming satisfaction with the course, better ultrasound preparedness, and improved comfort with central line insertion.

Monitoring of Air Pollution by Satellites (MAPS), phase 1

NASA Technical Reports Server (NTRS)

Ludwig, C. B.; Malkmus, W.; Griggs, M.; Bartle, E. R.

1972-01-01

Results are reported upon which the design of a satellite remote gas filter correlation (RGFC) instrument can be based. Although a final decision about the feasibility of measuring some of the pollutants with the required accuracy is still outstanding and subject to further theoretical and experimental verifications, viable concepts are presented which permit the initiation of the design phase. The pollutants which are of concern in the troposphere and stratosphere were selected. The infrared bands of these pollutants were identified, together with the bands of interfering gases, and the line parameters of the pollutants as well as interfering gases were generated through a computer program. Radiative transfer calculations (line-by-line) were made to establish the radiation levels at the top of the atmosphere and the signal levels at the detector of the RGFC instrument. Based upon these results the channels for the RGFC were selected. Finally, the problem areas, which need further investigations, were delineated and the supporting data requirements were established.

Real-time line matching from stereo images using a nonparametric transform of spatial relations and texture information

NASA Astrophysics Data System (ADS)

Park, Jonghee; Yoon, Kuk-Jin

2015-02-01

We propose a real-time line matching method for stereo systems. To achieve real-time performance while retaining a high level of matching precision, we first propose a nonparametric transform to represent the spatial relations between neighboring lines and nearby textures as a binary stream. Since the length of a line can vary across images, the matching costs between lines are computed within an overlap area (OA) based on the binary stream. The OA is determined for each line pair by employing the properties of a rectified image pair. Finally, the line correspondence is determined using a winner-takes-all method with a left-right consistency check. To reduce the computational time requirements further, we filter out unreliable matching candidates in advance based on their rectification properties. The performance of the proposed method was compared with state-of-the-art methods in terms of the computational time, matching precision, and recall. The proposed method required 47 ms to match lines from an image pair in the KITTI dataset with an average precision of 95%. We also verified the proposed method under image blur, illumination variation, and viewpoint changes.

Microarray-Based Mapping for the Detection of Molecular Markers in Response to Aspergillus flavus Infection in Susceptible and Resistant Maize Lines

USDA-ARS?s Scientific Manuscript database

The objectives of this study were (1) to evaluate differential gene expression levels for resistance to A. flavus kernel infection in susceptible (Va35) and resistant (Mp313E) maize lines using Oligonucleotide and cDNA microarray analysis, (2) to evaluate differences in A. flavus accumulation betwee...

Performance analysis of microcomputer based differential protection of UHV lines under selective phase switching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhatti, A.A.

1990-04-01

This paper examines the effects of primary and secondary fault quantities as well s of mutual couplings of neighboring circuits on the sensitivity of operation and threshold settings of a microcomputer based differential protection of UHV lines under selective phase switching. Microcomputer based selective phase switching allows the disconnection of minimum number of phases involved in a fault and requires the autoreclosing of these phases immediately after the extinction of secondary arc. During a primary fault a heavy current contribution to the healthy phases tends to cause an unwanted tripping. Faulty phases physically disconnected constitute an isolated fault which beingmore » coupled to the system affects the current and voltage levels of the healthy phases still retained in the system and may cause an unwanted tripping. The microcomputer based differential protection, appears to have poor performance when applied to uncompensated lines employing selective pole switching.« less

Intelligent RF-Based Gesture Input Devices Implemented Using e-Textiles †

PubMed Central

Hughes, Dana; Profita, Halley; Radzihovsky, Sarah; Correll, Nikolaus

2017-01-01

We present an radio-frequency (RF)-based approach to gesture detection and recognition, using e-textile versions of common transmission lines used in microwave circuits. This approach allows for easy fabrication of input swatches that can detect a continuum of finger positions and similarly basic gestures, using a single measurement line. We demonstrate that the swatches can perform gesture detection when under thin layers of cloth or when weatherproofed, providing a high level of versatility not present with other types of approaches. Additionally, using small convolutional neural networks, low-level gestures can be identified with a high level of accuracy using a small, inexpensive microcontroller, allowing for an intelligent fabric that reports only gestures of interest, rather than a simple sensor requiring constant surveillance from an external computing device. The resulting e-textile smart composite has applications in controlling wearable devices by providing a simple, eyes-free mechanism to input simple gestures. PMID:28125010

Intelligent RF-Based Gesture Input Devices Implemented Using e-Textiles.

PubMed

Hughes, Dana; Profita, Halley; Radzihovsky, Sarah; Correll, Nikolaus

2017-01-24

We present an radio-frequency (RF)-based approach to gesture detection and recognition, using e-textile versions of common transmission lines used in microwave circuits. This approach allows for easy fabrication of input swatches that can detect a continuum of finger positions and similarly basic gestures, using a single measurement line. We demonstrate that the swatches can perform gesture detection when under thin layers of cloth or when weatherproofed, providing a high level of versatility not present with other types of approaches. Additionally, using small convolutional neural networks, low-level gestures can be identified with a high level of accuracy using a small, inexpensive microcontroller, allowing for an intelligent fabric that reports only gestures of interest, rather than a simple sensor requiring constant surveillance from an external computing device. The resulting e-textile smart composite has applications in controlling wearable devices by providing a simple, eyes-free mechanism to input simple gestures.

Improving integrity of on-line grammage measurement with traceable basic calibration.

PubMed

Kangasrääsiö, Juha

2010-07-01

The automatic control of grammage (basis weight) in paper and board production is based upon on-line grammage measurement. Furthermore, the automatic control of other quality variables such as moisture, ash content and coat weight, may rely on the grammage measurement. The integrity of Kr-85 based on-line grammage measurement systems was studied, by performing basic calibrations with traceably calibrated plastic reference standards. The calibrations were performed according to the EN ISO/IEC 17025 standard, which is a requirement for calibration laboratories. The observed relative measurement errors were 3.3% in the first time calibrations at the 95% confidence level. With the traceable basic calibration method, however, these errors can be reduced to under 0.5%, thus improving the integrity of on-line grammage measurements. Also a standardised algorithm, based on the experience from the performed calibrations, is proposed to ease the adjustment of the different grammage measurement systems. The calibration technique can basically be applied to all beta-radiation based grammage measurements. 2010 ISA. Published by Elsevier Ltd. All rights reserved.

The insect ecdysone receptor is a good potential target for RNAi-based pest control.

PubMed

Yu, Rong; Xu, Xinping; Liang, Yongkang; Tian, Honggang; Pan, Zhanqing; Jin, Shouheng; Wang, Na; Zhang, Wenqing

2014-01-01

RNA interference (RNAi) has great potential for use in insect pest control. However, some significant challenges must be overcome before RNAi-based pest control can become a reality. One challenge is the proper selection of a good target gene for RNAi. Here, we report that the insect ecdysone receptor (EcR) is a good potential target for RNAi-based pest control in the brown planthopper Nilaparvata lugens, a serious insect pest of rice plants. We demonstrated that the use of a 360 bp fragment (NlEcR-c) that is common between NlEcR-A and NlEcR-B for feeding RNAi experiments significantly decreased the relative mRNA expression levels of NlEcR compared with those in the dsGFP control. Feeding RNAi also resulted in a significant reduction in the number of offspring per pair of N. lugens. Consequently, a transgenic rice line expressing NlEcR dsRNA was constructed by Agrobacterium- mediated transformation. The results of qRT-PCR showed that the total copy number of the target gene in all transgenic rice lines was 2. Northern blot analysis showed that the small RNA of the hairpin dsNlEcR-c was successfully expressed in the transgenic rice lines. After newly hatched nymphs of N. lugens fed on the transgenic rice lines, effective RNAi was observed. The NlEcR expression levels in all lines examined were decreased significantly compared with the control. In all lines, the survival rate of the nymphs was nearly 90%, and the average number of offspring per pair in the treated groups was significantly less than that observed in the control, with a decrease of 44.18-66.27%. These findings support an RNAi-based pest control strategy and are also important for the management of rice insect pests.

Patterns of Chemotherapy Use in a U.S.-Based Cohort of Patients with Metastatic Pancreatic Cancer.

PubMed

Abrams, Thomas A; Meyer, Gary; Meyerhardt, Jeffrey A; Wolpin, Brian M; Schrag, Deborah; Fuchs, Charles S

2017-08-01

Few population studies have examined patterns of systemic therapy administration in metastatic pancreatic cancer (MPC) or the predictors associated with specific treatment choices. We assessed 4,011 consecutive MPC patients who received chemotherapy between January 2005 and December 2015 at academic, private, and community-based oncology practices subscribing to a U.S.-wide chemotherapy order entry system capturing disease, patient, provider, and treatment data. Multivariate analyses of these prospectively recorded characteristics identified significant predictors of specific therapeutic choices. Overall, 100 different regimens were used in first-line treatment of MPC. First-line gemcitabine monotherapy usage fell steadily from 72% in 2006 to 16% in 2015. This steep decline mirrored increases in first-line usage of both 5 fluorouracil, leucovorin, irinotecan and oxaliplatin (FOLFIRINOX) and gemcitabine + nab-paclitaxel. Younger male patients were more likely to receive FOLFIRINOX as first-line treatment, whereas patients treated at community practices and by oncologists with lower MPC patient volume were more likely to receive gemcitabine plus nab-paclitaxel (all p  ≤ .05). Among all patients receiving first-line chemotherapy for MPC, 49% went on to receive second-line therapy and 19% received third-line therapy; administration of second- and third-line therapies increased steadily over the time course of follow-up. Younger patients and those treated by oncologists with higher MPC patient volume were more likely to receive second- and third-line therapies. This population-based study provides insight into treatment patterns of MPC in the U.S. Usage patterns varied greatly according to patient and provider characteristics. This study examined real world metastatic pancreatic cancer treatment patterns in the United States with the goals of understanding changes in chemotherapy treatment frequencies over time and determining the individual predictors that underlie the chemotherapy choices oncologists make for their patients. Our data set is unique in that it captured not only patient-level data, but also oncologist-level data. It also captured data from private and community practices as well as academic centers. To our knowledge, this is the only data set that can give this degree of insight into oncologist decision making practices. © AlphaMed Press 2017.

Cyclotron Lines in Accreting Neutron Star Spectra

NASA Astrophysics Data System (ADS)

Wilms, Jörn; Schönherr, Gabriele; Schmid, Julia; Dauser, Thomas; Kreykenbohm, Ingo

2009-05-01

Cyclotron lines are formed through transitions of electrons between discrete Landau levels in the accretion columns of accreting neutron stars with strong (1012 G) magnetic fields. We summarize recent results on the formation of the spectral continuum of such systems, describe recent advances in the modeling of the lines based on a modification of the commonly used Monte Carlo approach, and discuss new results on the dependence of the measured cyclotron line energy from the luminosity of transient neutron star systems. Finally, we show that Simbol-X will be ideally suited to build and improve the observational database of accreting and strongly magnetized neutron stars.

ExoMol molecular line lists - XXVI: spectra of SH and NS

NASA Astrophysics Data System (ADS)

Yurchenko, Sergei N.; Bond, Wesley; Gorman, Maire N.; Lodi, Lorenzo; McKemmish, Laura K.; Nunn, William; Shah, Rohan; Tennyson, Jonathan

2018-04-01

Line lists for the sulphur-containing molecules SH (the mercapto radical) and NS are computed as part of the ExoMol project. These line lists consider transitions within the X 2Π ground state for 32SH, 33SH, 34SH and 32SD, and 14N32S, 14N33S, 14N34S, 14N36S and 15N32S. Ab initio potential energy (PEC) and spin-orbit coupling (SOC) curves are computed and then improved by fitting to experimentally observed transitions. Fully ab initio dipole moment curves (DMCs) computed at high level of theory are used to produce the final line lists. For SH, our fit gives a root-mean-square (rms) error of 0.03 cm-1 between the observed (vmax = 4, Jmax = 34.5) and calculated transitions wavenumbers; this is extrapolated such that all X 2Π rotational-vibrational-electronic (rovibronic) bound states are considered. For 32SH the resulting line list contains about 81 000 transitions and 2 300 rovibronic states, considering levels up to vmax = 14 and Jmax = 60.5. For NS the refinement used a combination of experimentally determined frequencies and energy levels and led to an rms fitting error of 0.002 cm-1. Each NS calculated line list includes around 2.8 million transitions and 31 000 rovibronic states with a vibrational range up to v = 53 and rotational range to J = 235.5, which covers up to 23 000 cm-1. Both line lists should be complete for temperatures up to 5000 K. Example spectra simulated using this line list are shown and comparisons made to the existing data in the CDMS database. The line lists are available from the CDS (http://cdsarc.u-strasbg.fr) and ExoMol (www.exomol.com) data bases.

Evaluation of width and width uniformity of near-field electrospinning printed micro and sub-micrometer lines based on optical image processing

NASA Astrophysics Data System (ADS)

Zhao, Libo; Xia, Yong; Hebibul, Rahman; Wang, Jiuhong; Zhou, Xiangyang; Hu, Yingjie; Li, Zhikang; Luo, Guoxi; Zhao, Yulong; Jiang, Zhuangde

2018-03-01

This paper presents an experimental study using image processing to investigate width and width uniformity of sub-micrometer polyethylene oxide (PEO) lines fabricated by near-filed electrospinning (NFES) technique. An adaptive thresholding method was developed to determine the optimal gray values to accurately extract profiles of printed lines from original optical images. And it was proved with good feasibility. The mechanism of the proposed thresholding method was believed to take advantage of statistic property and get rid of halo induced errors. Triangular method and relative standard deviation (RSD) were introduced to calculate line width and width uniformity, respectively. Based on these image processing methods, the effects of process parameters including substrate speed (v), applied voltage (U), nozzle-to-collector distance (H), and syringe pump flow rate (Q) on width and width uniformity of printed lines were discussed. The research results are helpful to promote the NFES technique for fabricating high resolution micro and sub-micro lines and also helpful to optical image processing at sub-micro level.

Mg I as a probe of the solar chromosphere - The atomic model

NASA Technical Reports Server (NTRS)

Mauas, Pablo J.; Avrett, Eugene H.; Loeser, Rudolf

1988-01-01

This paper presents a complete atomic model for Mg I line synthesis, where all the atomic parameters are based on recent experimental and theoretical data. It is shown how the computed profiles at 4571 A and 5173 A are influenced by the choice of these parameters and the number of levels included in the model atom. In addition, observed profiles of the 5173 A b2 line and theoretical profiles for comparison (based on a recent atmospheric model for the average quiet sun) are presented.

High-frequency characterization and modeling of single metallic nanowires

NASA Astrophysics Data System (ADS)

Hsu, Chuan-Lun; Ardila, Gustavo; Benech, Philippe

2013-07-01

The transmission line characteristics of an individual aluminum metallic nanowire up to 100 GHz are presented in this paper. We have built a reliable framework for characterizing such nanowires using a specially designed coplanar waveguide platform. We systematically estimate the pad parasitics, contact impedance and transmission line parameters based on an equivalent circuit model and cascade-based de-embedding theory. This is the first time that such external parasitic elements have been successfully removed from a nanoscale transmission line. The extracted frequency-dependent electrical responses show good signal levels and a high degree of reproducibility. Contribution to the Topical Issue “International Semiconductor Conference Dresden-Grenoble - ISCDG 2012”, Edited by Gérard Ghibaudo, Francis Balestra and Simon Deleonibus.

Polar versus temperate grounding-line sedimentary systems and marine glacier stability during sea level rise by global warming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Powell, R.D.; Pyne, A.R.; Hunter, L.E.

1992-01-01

Marine-ending glaciers may retreat with global warming as sea level rises by ocean thermal expansion. If the sea floor rises by sediment accumulation, then glaciers may not feel the effect of sea level rise. A submersible ROV and other techniques have been used to collect data from temperate and polar glaciers to compare sediment production and mass balance of their grounding-line systems. Temperature Alaskan valley glaciers flow at about 0.2--2 km/a and have high volumes of supraglacial, englacial and subglacial debris. However, most sediment contributed to the base of their tidewater cliffs comes from subglacial streams or squeezing out subglacialmore » sediment and pushing it with other marine sediment into a morainal bank. Blue Glacier, a thin, locally fed polar glacier in Antarctica, flows slowly and has minimal glacial debris. The grounding-line system at the tidewater cliff is a morainal bank that forms solely by pushing of marine sediment. An Antarctic polar outlet glacier, Mackay Glacier, terminating as a floating glacier-tongue, has similar volumes of basal debris to Alaskan temperature glaciers and flows at 250 m/a. However, no subglacial streams issued from Mackay's grounding line and all sedimentation was by rockfall and grainfall rainout from seawater undermelt of the tongue. A grounding-line wedge of glacimarine diamicton is deposited over subglacial (lodgement ) till. Although Antarctic grounding-line accumulation rates are three orders of magnitude smaller than Alaskan rates, both are capable of compensating for predicted rises in sea level by thermal heating from global warming.« less

Scan Line Based Road Marking Extraction from Mobile LiDAR Point Clouds.

PubMed

Yan, Li; Liu, Hua; Tan, Junxiang; Li, Zan; Xie, Hong; Chen, Changjun

2016-06-17

Mobile Mapping Technology (MMT) is one of the most important 3D spatial data acquisition technologies. The state-of-the-art mobile mapping systems, equipped with laser scanners and named Mobile LiDAR Scanning (MLS) systems, have been widely used in a variety of areas, especially in road mapping and road inventory. With the commercialization of Advanced Driving Assistance Systems (ADASs) and self-driving technology, there will be a great demand for lane-level detailed 3D maps, and MLS is the most promising technology to generate such lane-level detailed 3D maps. Road markings and road edges are necessary information in creating such lane-level detailed 3D maps. This paper proposes a scan line based method to extract road markings from mobile LiDAR point clouds in three steps: (1) preprocessing; (2) road points extraction; (3) road markings extraction and refinement. In preprocessing step, the isolated LiDAR points in the air are removed from the LiDAR point clouds and the point clouds are organized into scan lines. In the road points extraction step, seed road points are first extracted by Height Difference (HD) between trajectory data and road surface, then full road points are extracted from the point clouds by moving least squares line fitting. In the road markings extraction and refinement step, the intensity values of road points in a scan line are first smoothed by a dynamic window median filter to suppress intensity noises, then road markings are extracted by Edge Detection and Edge Constraint (EDEC) method, and the Fake Road Marking Points (FRMPs) are eliminated from the detected road markings by segment and dimensionality feature-based refinement. The performance of the proposed method is evaluated by three data samples and the experiment results indicate that road points are well extracted from MLS data and road markings are well extracted from road points by the applied method. A quantitative study shows that the proposed method achieves an average completeness, correctness, and F-measure of 0.96, 0.93, and 0.94, respectively. The time complexity analysis shows that the scan line based road markings extraction method proposed in this paper provides a promising alternative for offline road markings extraction from MLS data.

Scan Line Based Road Marking Extraction from Mobile LiDAR Point Clouds†

PubMed Central

Yan, Li; Liu, Hua; Tan, Junxiang; Li, Zan; Xie, Hong; Chen, Changjun

2016-01-01

Mobile Mapping Technology (MMT) is one of the most important 3D spatial data acquisition technologies. The state-of-the-art mobile mapping systems, equipped with laser scanners and named Mobile LiDAR Scanning (MLS) systems, have been widely used in a variety of areas, especially in road mapping and road inventory. With the commercialization of Advanced Driving Assistance Systems (ADASs) and self-driving technology, there will be a great demand for lane-level detailed 3D maps, and MLS is the most promising technology to generate such lane-level detailed 3D maps. Road markings and road edges are necessary information in creating such lane-level detailed 3D maps. This paper proposes a scan line based method to extract road markings from mobile LiDAR point clouds in three steps: (1) preprocessing; (2) road points extraction; (3) road markings extraction and refinement. In preprocessing step, the isolated LiDAR points in the air are removed from the LiDAR point clouds and the point clouds are organized into scan lines. In the road points extraction step, seed road points are first extracted by Height Difference (HD) between trajectory data and road surface, then full road points are extracted from the point clouds by moving least squares line fitting. In the road markings extraction and refinement step, the intensity values of road points in a scan line are first smoothed by a dynamic window median filter to suppress intensity noises, then road markings are extracted by Edge Detection and Edge Constraint (EDEC) method, and the Fake Road Marking Points (FRMPs) are eliminated from the detected road markings by segment and dimensionality feature-based refinement. The performance of the proposed method is evaluated by three data samples and the experiment results indicate that road points are well extracted from MLS data and road markings are well extracted from road points by the applied method. A quantitative study shows that the proposed method achieves an average completeness, correctness, and F-measure of 0.96, 0.93, and 0.94, respectively. The time complexity analysis shows that the scan line based road markings extraction method proposed in this paper provides a promising alternative for offline road markings extraction from MLS data. PMID:27322279

Fluorescent excitation of Fe 2, Mn 2, Ti 2, N 1 lines by V 4, N 5, O 6: Emission lines in the spectra of symbiotic stars and Seyfert galaxies

NASA Technical Reports Server (NTRS)

Gilra, D. P.

1984-01-01

Analysis of the published IUE and ground based high resolution spectra of symbiotic stars, particularly RR Tel, shows that the dominant excitation mechanism of Fe II, Mn II, Ti II, and N I lines is the selective fluorescent excitation of some levels by the strong C IV, N V, and O VI emission lines. The same mechanism should work for the excitation of Fe II lines in the spectra of Seyfert galaxies and Q60's whose emission spectra are quite similar to those of symbiotic stars. The similarities and differences between the fluroescent excitation mechanism reported herein and the Bowen's mechanism is analyzed.

The optical frequency comb fibre spectrometer

PubMed Central

Coluccelli, Nicola; Cassinerio, Marco; Redding, Brandon; Cao, Hui; Laporta, Paolo; Galzerano, Gianluca

2016-01-01

Optical frequency comb sources provide thousands of precise and accurate optical lines in a single device enabling the broadband and high-speed detection required in many applications. A main challenge is to parallelize the detection over the widest possible band while bringing the resolution to the single comb-line level. Here we propose a solution based on the combination of a frequency comb source and a fibre spectrometer, exploiting all-fibre technology. Our system allows for simultaneous measurement of 500 isolated comb lines over a span of 0.12 THz in a single acquisition; arbitrarily larger span are demonstrated (3,500 comb lines over 0.85 THz) by doing sequential acquisitions. The potential for precision measurements is proved by spectroscopy of acetylene at 1.53 μm. Being based on all-fibre technology, our system is inherently low-cost, lightweight and may lead to the development of a new class of broadband high-resolution spectrometers. PMID:27694981

E-Textile Embroidered Metamaterial Transmission Line for Signal Propagation Control.

PubMed

Moradi, Bahareh; Fernández-García, Raul; Gil, Ignacio

2018-06-05

In this paper, the utilization of common fabrics for the manufacturing of e-textile metamaterial transmission lines is investigated. In order to filter and control the signal propagation in the ultra-high frequency (UHF) range along the e-textile, a conventional metamaterial transmission line was compared with embroidered metamaterial particles. The proposed design was based on a transmission line loaded with one or several split-ring resonators (SRR) on a felt substrate. To explore the relations between physical parameters and filter performance characteristics, theoretical models based on transmission matrices' description of the filter constituent components were proposed. Excellent agreement between theoretical prediction, electromagnetic simulations, and measurement were found. Experimental results showed stop-band levels higher than -30 dB for compact embroidered metamaterial e-textiles. The validated results confirmed embroidery as a useful technique to obtain customized electromagnetic properties, such as filtering, on wearable applications.

A study on low-cost, high-accuracy, and real-time stereo vision algorithms for UAV power line inspection

NASA Astrophysics Data System (ADS)

Wang, Hongyu; Zhang, Baomin; Zhao, Xun; Li, Cong; Lu, Cunyue

2018-04-01

Conventional stereo vision algorithms suffer from high levels of hardware resource utilization due to algorithm complexity, or poor levels of accuracy caused by inadequacies in the matching algorithm. To address these issues, we have proposed a stereo range-finding technique that produces an excellent balance between cost, matching accuracy and real-time performance, for power line inspection using UAV. This was achieved through the introduction of a special image preprocessing algorithm and a weighted local stereo matching algorithm, as well as the design of a corresponding hardware architecture. Stereo vision systems based on this technique have a lower level of resource usage and also a higher level of matching accuracy following hardware acceleration. To validate the effectiveness of our technique, a stereo vision system based on our improved algorithms were implemented using the Spartan 6 FPGA. In comparative experiments, it was shown that the system using the improved algorithms outperformed the system based on the unimproved algorithms, in terms of resource utilization and matching accuracy. In particular, Block RAM usage was reduced by 19%, and the improved system was also able to output range-finding data in real time.

A new cognitive rehabilitation programme for patients with multiple sclerosis: the 'MS-line! Project'.

PubMed

Gich, Jordi; Freixenet, Jordi; Garcia, Rafael; Vilanova, Joan Carles; Genís, David; Silva, Yolanda; Montalban, Xavier; Ramió-Torrentà, Lluís

2015-09-01

Cognitive rehabilitation is often delayed in multiple sclerosis (MS). To develop a free and specific cognitive rehabilitation programme for MS patients to be used from early stages that does not interfere with daily living activities. MS-line!, cognitive rehabilitation materials consisting of written, manipulative and computer-based materials with difficulty levels developed by a multidisciplinary team. Mathematical, problem-solving and word-based exercises were designed. Physical materials included spatial, coordination and reasoning games. Computer-based material included logic and reasoning, working memory and processing speed games. Cognitive rehabilitation exercises that are specific for MS patients have been successfully developed. © The Author(s), 2014.

Density-based clustering analyses to identify heterogeneous cellular sub-populations

NASA Astrophysics Data System (ADS)

Heaster, Tiffany M.; Walsh, Alex J.; Landman, Bennett A.; Skala, Melissa C.

2017-02-01

Autofluorescence microscopy of NAD(P)H and FAD provides functional metabolic measurements at the single-cell level. Here, density-based clustering algorithms were applied to metabolic autofluorescence measurements to identify cell-level heterogeneity in tumor cell cultures. The performance of the density-based clustering algorithm, DENCLUE, was tested in samples with known heterogeneity (co-cultures of breast carcinoma lines). DENCLUE was found to better represent the distribution of cell clusters compared to Gaussian mixture modeling. Overall, DENCLUE is a promising approach to quantify cell-level heterogeneity, and could be used to understand single cell population dynamics in cancer progression and treatment.

3-Bromopyruvate induces necrotic cell death in sensitive melanoma cell lines.

PubMed

Qin, J-Z; Xin, H; Nickoloff, B J

2010-05-28

Clinicians successfully utilize high uptake of radiolabeled glucose via PET scanning to localize metastases in melanoma patients. To take advantage of this altered metabolome, 3-bromopyruvate (BrPA) was used to overcome the notorious resistance of melanoma to cell death. Using four melanoma cell lines, BrPA triggered caspase independent necrosis in two lines, whilst the other two lines were resistant to killing. Mechanistically, sensitive cells differed from resistant cells by; constitutively lower levels of glutathione, reduction of glutathione by BrPA only in sensitive cells; increased superoxide anion reactive oxygen species, loss of outer mitochondrial membrane permeability, and rapid ATP depletion. Sensitive cell killing was blocked by N-acetylcysteine or glutathione. When glutathione levels were reduced in resistant cell lines, they became sensitive to killing by BrPA. Taken together, these results identify a metabolic-based Achilles' heel in melanoma cells to be exploited by use of BrPA. Future pre-clinical and clinical trials are warranted to translate these results into improved patient care for individuals suffering from metastatic melanoma. Copyright (c) 2010 Elsevier Inc. All rights reserved.

3-Bromopyruvate induces necrotic cell death in sensitive melanoma cell lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qin, J.-Z.; Xin, H.; Nickoloff, B.J., E-mail: bnickol@lumc.edu

2010-05-28

Clinicians successfully utilize high uptake of radiolabeled glucose via PET scanning to localize metastases in melanoma patients. To take advantage of this altered metabolome, 3-bromopyruvate (BrPA) was used to overcome the notorious resistance of melanoma to cell death. Using four melanoma cell lines, BrPA triggered caspase independent necrosis in two lines, whilst the other two lines were resistant to killing. Mechanistically, sensitive cells differed from resistant cells by; constitutively lower levels of glutathione, reduction of glutathione by BrPA only in sensitive cells; increased superoxide anion reactive oxygen species, loss of outer mitochondrial membrane permeability, and rapid ATP depletion. Sensitive cellmore » killing was blocked by N-acetylcysteine or glutathione. When glutathione levels were reduced in resistant cell lines, they became sensitive to killing by BrPA. Taken together, these results identify a metabolic-based Achilles' heel in melanoma cells to be exploited by use of BrPA. Future pre-clinical and clinical trials are warranted to translate these results into improved patient care for individuals suffering from metastatic melanoma.« less

MARVEL analysis of the measured high-resolution spectra of 14NH3

NASA Astrophysics Data System (ADS)

Al Derzi, Afaf R.; Furtenbacher, Tibor; Tennyson, Jonathan; Yurchenko, Sergei N.; Császár, Attila G.

2015-08-01

Accurate, experimental rotational-vibrational energy levels and line positions, with associated labels and uncertainties, are reported for the ground electronic state of the symmetric-top 14NH3 molecule. All levels and lines are based on critically reviewed and validated high-resolution experimental spectra taken from 56 literature sources. The transition data are in the 0.7-17 000 cm-1 region, with a large gap between 7000 and 15 000 cm-1. The MARVEL (Measured Active Rotational-Vibrational Energy Levels) algorithm is used to determine the energy levels. Out of the 29 450 measured transitions 10 041 and 18 947 belong to ortho- and para-14NH3, respectively. A careful analysis of the related experimental spectroscopic network (SN) allows 28 530 of the measured transitions to be validated, 18 178 of these are unique, while 462 transitions belong to floating components. Despite the large number of spectroscopic measurements published over the last 80 years, the transitions determine only 30 vibrational band origins of 14NH3, 8 for ortho- and 22 for para-14NH3. The highest J value, where J stands for the rotational quantum number, for which an energy level is validated is 31. The number of experimental-quality ortho- and para-14NH3 rovibrational energy levels is 1724 and 3237, respectively. The MARVEL energy levels are checked against ones in the BYTe first-principles database, determined previously. The lists of validated lines and levels for 14NH3 are deposited in the Supporting Information to this paper. Combination of the MARVEL energy levels with first-principles absorption intensities yields a huge number of experimental-quality rovibrational lines, which should prove to be useful for the understanding of future complex high-resolution spectroscopy on 14NH3; these lines are also deposited in the Supporting Information to this paper.

'Ogura'-based 'CMS' lines with different nuclear backgrounds of cabbage revealed substantial diversity at morphological and molecular levels.

PubMed

Parkash, Chander; Kumar, Sandeep; Singh, Rajender; Kumar, Ajay; Kumar, Satish; Dey, Shyam Sundar; Bhatia, Reeta; Kumar, Raj

2018-01-01

A comprehensive study on characterization and genetic diversity analysis was carried out in 16 'Ogura'-based 'CMS' lines of cabbage using 14 agro-morphological traits and 29 SSR markers. Agro-morphological characterization depicted considerable variations for different horticultural traits studied. The genotype, ZHA-2, performed better for most of the economically important quantitative traits. Further, gross head weight (0.76), head length (0.60) and head width (0.83) revealed significant positive correlation with net head weight. Dendrogram based on 10 quantitative traits exhibited considerable diversity among different CMS lines and principle component analysis (PCA) indicated that net and gross head weight, and head length and width are the main components of divergence between 16 CMS lines of cabbage. In molecular study, a total of 58 alleles were amplified by 29 SSR primers, averaging to 2.0 alleles in each locus. High mean values of Shannon's Information index (0.62), expected (0.45) and observed (0.32) heterozygosity and polymorphic information content (0.35) depicted substantial polymorphism. Dendrogram based on Jaccard's similarity coefficient constructed two major groups and eight sub-groups, which revealed substantial diversity among different CMS lines. In overall, based on agro-morphological and molecular studies genotype RRMA, ZHA-2 and RCA were found most divergent. Hence, they have immense potential in future breeding programs for the high-yielding hybrid development in cabbage.

Inhibition of mutant IDH1 decreases D-2-HG levels without affecting tumorigenic properties of chondrosarcoma cell lines.

PubMed

Suijker, Johnny; Oosting, Jan; Koornneef, Annemarie; Struys, Eduard A; Salomons, Gajja S; Schaap, Frank G; Waaijer, Cathelijn J F; Wijers-Koster, Pauline M; Briaire-de Bruijn, Inge H; Haazen, Lizette; Riester, Scott M; Dudakovic, Amel; Danen, Erik; Cleton-Jansen, Anne-Marie; van Wijnen, Andre J; Bovée, Judith V M G

2015-05-20

Mutations in isocitrate dehydrogenase 1 (IDH1) and IDH2 are found in a subset of benign and malignant cartilage tumors, gliomas and leukaemias. The mutant enzyme causes the production of D-2-hydroxyglutarate (D-2-HG), affecting CpG island and histone methylation. While mutations in IDH1/2 are early events in benign cartilage tumors, we evaluated whether these mutations play a role in malignant chondrosarcomas. Compared to IDH1/2 wildtype cell lines, chondrosarcoma cell lines harboring an endogenous IDH1 (n=3) or IDH2 mutation (n=2) showed up to a 100-fold increase in intracellular and extracellular D-2-HG levels. Specific inhibition of mutant IDH1 using AGI-5198 decreased levels of D-2-HG in a dose dependent manner. After 72 hours of treatment one out of three mutant IDH1 cell lines showed a moderate decrease in viability , while D-2-HG levels decreased >90%. Likewise, prolonged treatment (up to 20 passages) did not affect proliferation and migration. Furthermore, global gene expression, CpG island methylation as well as histone H3K4, -9, and -27 trimethylation levels remained unchanged. Thus, while IDH1/2 mutations cause enchondroma, malignant progression towards central chondrosarcoma renders chondrosarcoma growth independent of these mutations. Thus, monotherapy based on inhibition of mutant IDH1 appears insufficient for treatment of inoperable or metastasized chondrosarcoma patients.

Genetic manipulation of the γ-aminobutyric acid (GABA) shunt in rice: overexpression of truncated glutamate decarboxylase (GAD2) and knockdown of γ-aminobutyric acid transaminase (GABA-T) lead to sustained and high levels of GABA accumulation in rice kernels.

PubMed

Shimajiri, Yasuka; Oonishi, Takayuki; Ozaki, Kae; Kainou, Kumiko; Akama, Kazuhito

2013-06-01

Gamma-aminobutyric acid (GABA) is a non-protein amino acid commonly present in all organisms. Because cellular levels of GABA in plants are mainly regulated by synthesis (glutamate decarboxylase, GAD) and catabolism (GABA-transaminase, GABA-T), we attempted seed-specific manipulation of the GABA shunt to achieve stable GABA accumulation in rice. A truncated GAD2 sequence, one of five GAD genes, controlled by the glutelin (GluB-1) or rice embryo globulin promoters (REG) and GABA-T-based trigger sequences in RNA interference (RNAi) cassettes controlled by one of these promoters as well, was introduced into rice (cv. Koshihikari) to establish stable transgenic lines under herbicide selection using pyriminobac. T₁ and T₂ generations of rice lines displayed high GABA concentrations (2-100 mg/100 g grain). In analyses of two selected lines from the T₃ generation, there was a strong correlation between GABA level and the expression of truncated GAD2, whereas the inhibitory effect of GABA-T expression was relatively weak. In these two lines both with two T-DNA copies, their starch, amylose, and protein levels were slightly lower than non-transformed cv. Koshihikari. Free amino acid analysis of mature kernels of these lines demonstrated elevated levels of GABA (75-350 mg/100 g polished rice) and also high levels of several amino acids, such as Ala, Ser, and Val. Because these lines of seeds could sustain their GABA content after harvest (up to 6 months), the strategy in this study could lead to the accumulation GABA and for these to be sustained in the edible parts. © 2013 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

An In Vivo Evaluation of the Fit of Zirconium-Oxide Based, Ceramic Single Crowns with Vertical and Horizontal Finish Line Preparations.

PubMed

Vigolo, Paolo; Mutinelli, Sabrina; Biscaro, Leonello; Stellini, Edoardo

2015-12-01

Different types of tooth preparations influence the marginal precision of zirconium-oxide based ceramic single crowns. In this in vivo study, the marginal fits of zirconium-oxide based ceramic single crowns with vertical and horizontal finish lines were compared. Forty-six teeth were chosen in eight patients indicated for extraction for implant placement. CAD/CAM technology was used for the production of 46 zirconium-oxide-based ceramic single crowns: 23 teeth were prepared with vertical finishing lines, 23 with horizontal finishing lines. One operator accomplished all clinical procedures. The zirconia crowns were cemented with glass ionomer cement. The teeth were extracted 1 month later. Marginal gaps along vertical planes were measured for each crown, using a total of four landmarks for each tooth by means of a microscope at 50× magnification. On conclusion of microscopic assessment, ESEM evaluation was completed on all specimens. The comparison of the gap between the two types of preparation was performed with a nonparametric test (two-sample Wilcoxon rank-sum test) with a level of significance fixed at p < 0.05. All data were analyzed with STATA12. In the group with horizontal finish line preparations, the median value of the gap was 35.45 μm (Iqr, 0.33); for the vertical finish line group, the median value of the gap was 35.44 μm (Iqr, 0.40). The difference between the two groups was not statistically significant (two-sample Wilcoxon rank-sum test, p = 0.0872). Within the limitations of this study, the gaps of the zirconium-oxide-based ceramic CAD/CAM crowns with vertical and horizontal finish line preparations were not different. © 2015 by the American College of Prosthodontists.

Second-Line Antiretroviral Therapy in a Workplace and Community-Based Treatment Programme in South Africa: Determinants of Virological Outcome

PubMed Central

Johnston, Victoria; Fielding, Katherine; Charalambous, Salome; Mampho, Mildred; Churchyard, Gavin; Phillips, Andrew; Grant, Alison D.

2012-01-01

Background: As antiretroviral treatment (ART) programmes in resource-limited settings mature, more patients are experiencing virological failure. Without resistance testing, deciding who should switch to second-line ART can be difficult. The consequences for second-line outcomes are unclear. In a workplace- and community-based multi-site programme, with 6-monthly virological monitoring, we describe outcomes and predictors of viral suppression on second-line, protease inhibitor-based ART. Methods: We used prospectively collected clinic data from patients commencing first-line ART between 1/1/03 and 31/12/08 to construct a study cohort of patients switched to second-line ART in the presence of a viral load (VL) ≥400 copies/ml. Predictors of VL<400 copies/ml within 15 months of switch were assessed using modified Poisson regression to estimate risk ratios. Results: 205 workplace patients (91.7% male; median age 43 yrs) and 212 community patients (38.7% male; median age 36 yrs) switched regimens. At switch compared to community patients, workplace patients had a longer duration of viraemia, higher VL, lower CD4 count, and higher reported non-adherence on first-line ART. Non-adherence was the reported reason for switching in a higher proportion of workplace patients. Following switch, 48.3% (workplace) and 72.0% (community) achieved VL<400, with non-adherence (17.9% vs. 1.4%) and virological rebound (35.6% vs. 13.2% with available measures) reported more commonly in the workplace programme. In adjusted analysis of the workplace programme, lower switch VL and younger age were associated with VL<400. In the community programme, shorter duration of viraemia, higher CD4 count and transfers into programme on ART were associated with VL<400. Conclusion: High levels of viral suppression on second-line ART can be, but are not always, achieved in multi-site treatment programmes with both individual- and programme-level factors influencing outcomes. Strategies to support both healthcare workers and patients during this switch period need to be evaluated; sub-optimal adherence, particularly in the workplace programme must be addressed. PMID:22666338

Geometry of the Valgus Knee: Contradicting the Dogma of a Femoral-Based Deformity.

PubMed

Eberbach, Helge; Mehl, Julian; Feucht, Matthias J; Bode, Gerrit; Südkamp, Norbert P; Niemeyer, Philipp

2017-03-01

Realignment osteotomies of valgus knee deformities are usually performed at the distal femur, as valgus alignment is considered to be a femoral-based deformity. This dogma, however, has not been proven in a large patient population. Valgus malalignment may also be caused by a tibial deformity or a combined tibial and femoral deformity. The purposes of this study were (1) to analyze the coronal geometry of patients with valgus malalignment and identify the location of the underlying deformity and (2) to investigate the proportion of cases that require realignment osteotomy at the tibia, the femur, or both locations to avoid an oblique joint line. Cross-sectional study; Level of evidence, 3. The analysis included 420 standing full-leg radiographs of patients with valgus malalignment (mechanical femorotibial angle [mFTA], ≥4°). A systematic analysis of the coronal leg geometry was performed including the mFTA, mechanical lateral distal femoral angle (mLDFA), mechanical medial proximal tibial angle (mMPTA), and joint-line convergence angle (JLCA). The localization of the deformity was determined according to the malalignment test described by Paley, and patients were assigned to 1 of 4 groups: femoral-based valgus deformity, tibial-based valgus deformity, femoral- and tibial-based valgus deformity, or intra-articular/ligamentary-based valgus deformity. Subsequently, the ideal osteotomy site was identified with the goal of a postoperative change of the joint line of two different maximum values, ±2° and ±4°, from its physiological varus position of 3°. Measurements of the coronal alignment revealed a mean (±SD) mFTA of 7.4° ± 4.3° (range, 4°-28.2°). The mean mLDFA and mean mMPTA were 84.8° ± 2.4° and 90.9° ± 2.6°, respectively. The mean JLCA was 1.2° ± 3.1°. The majority (41.0%) of valgus deformities were tibial based, 23.6% were femoral based, 26.9% were femoral and tibial based, and 8.6% were intra-articular/ligamentary based. To achieve a straight-leg axis and an anatomic postoperative joint line with a tolerance of ±4°, the ideal site of a corrective osteotomy was tibial in 55.2% of cases and femoral in 19.5% of cases. A double-level osteotomy would be necessary in 25.2% of cases. With a tolerance of ±2°, the ideal osteotomy site was the proximal tibia in 41.0% of cases and the distal femur in 13.6% of cases; a double-level osteotomy would be necessary in 45.5% of cases. In contrast to the widespread belief that valgus malalignment is usually caused by a femoral deformity, this study found that valgus malalignment was attributable to tibial deformity in the majority of patients. In addition, a combined femoral- and tibial-based deformity was more common than an isolated femoral-based deformity. As a clinical consequence, varus osteotomies to treat lateral compartment osteoarthritis must be performed at the tibial site or as a double-level osteotomy in a relevant number of patients to avoid an oblique joint line.

Ames-2016 line lists for 13 isotopologues of CO2: Updates, consistency, and remaining issues

NASA Astrophysics Data System (ADS)

Huang (黄新川), Xinchuan; Schwenke, David W.; Freedman, Richard S.; Lee, Timothy J.

2017-12-01

A new 626-based Ames-2 PES refinement and Ames-2016 line lists for 13 CO2 isotopologues are reported. A consistent σRMS = ±0.02 cm-1 is established for hundreds of isotopologue band origins using the Ames-2 PES. Ames-2016 line lists are computed at 296 K, 1000 K and 4000 K using the Ames-2 PES and the same DMS-N2 dipole surface used previously, with J up to 150, E‧ up to 24,000 cm-1 or 18,000 cm-1 and appropriate intensity cutoffs. The lists are compared to the CDSD-296, CDSD-4000 databases, UCL line lists, and a few recent highly accurate CO2 intensity measurements. Both agreements and discrepancies are discussed. Compared to the old Ames CO2 lists, the Ames-2016 line lists have line position deviations reduced by 50% or more, which consequently leads to more reliable intensities. The line shape parameters in the Ames-2016 line lists are predicted using the newly assigned conventional vibrational polyad quantum numbers for rovibrational levels below 12,000 cm-1 so the quality of the line shape parameters is similar to that of CDSD or HITRAN. This study further proves that a semi-empirically refined PES (Ames-1 and Ames-2) coupled with a high quality ab initio DMS (DMS-N2 and UCL) may generate IR predictions with consistent accuracy and is thus helpful in the analysis of laboratory spectra and simulations of various isotopologues. The Ames-2016 lists based on DMS-N2 have reached the ∼1% intensity prediction accuracy level for the recent 626 30013-00001 and 20013-00001 bands, but further quantification and improvements require sub-percent or sub-half-percent accurate experimental intensities. The inter-isotopologue consistency of the intensity prediction accuracies should have reached better than 1-3% for regular bands not affected by resonances. Since the Effective Dipole Models (EDM) in CDSD and HITRAN have 1-20% or even larger uncertainties, we show that the Ames lists can provide better alternative IR data for many hard-to-determine isotopologue bands. Comparison at 4000 K suggests that the Ames-4000 K 12C16O2 line list is reliable and consistent within the current cutoffs of J ≤ 150 and E‧ ≤ 24,000 cm-1, but intensity contributions involving higher energy levels should not be omitted and future computations need to be converged up to at least 32,000 cm-1 or higher. The remaining issues are discussed regarding the source of energy level discrepancies, intensity underestimations by ∼50% for some weak bands, etc. and also future work.

The Changeable Block Distance System Analysis

NASA Astrophysics Data System (ADS)

Lewiński, Andrzej; Toruń, Andrzej

The paper treats about efficiency analysis in Changeable Block Distance (CBD) System connected with wireless positioning and control of train. The analysis is based on modeling of typical ERTMS line and comparison with actual and future traffic. The calculations are related to assumed parameters of railway traffic corresponding to real time - table of distance Psary - Góra Włodowska from CMK line equipped in classic, ETCS Level 1 and ETCS with CBD systems.

Parallel Hough Transform-Based Straight Line Detection and Its FPGA Implementation in Embedded Vision

PubMed Central

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-01-01

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness. PMID:23867746

Parallel Hough Transform-based straight line detection and its FPGA implementation in embedded vision.

PubMed

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-07-17

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness.

Population trapping: The mechanism for the lost resonance lines in Pm-like ions

NASA Astrophysics Data System (ADS)

Kato, Daiji; Sakaue, Hiroyuki A.; Murakami, Izumi; Nakamura, Nobuyuki

2017-10-01

We report a population kinetics study on line emissions of the Pm-like Bi22+ performed by using a collisional-radiative (CR) model. Population rates of excited levels are analyzed to explain the population trapping in the 4f135s2 state which causes the loss of the 5s - 5p resonance lines in emission spectra. Based on the present analysis, we elucidate why the population trapping is not facilitated for a meta-stable excited level of the Sm-like Bi21+. The emission line spectra are calculated for the Pm-like isoelectronic sequence from Au18+ through W13+ and compared with experimental measurements by electron-beam-ion-traps (EBITs). Structures of the spectra are similar for all of the cases except for calculated W13+ spectra. The calculated spectra are hardly reconciled with the measured W13+ spectrum using the compact electron-beam-ion-trap (CoBIT) [Phys. Rev. A 92 (2015) 022510].

Simulation-based intelligent robotic agent for Space Station Freedom

NASA Technical Reports Server (NTRS)

Biegl, Csaba A.; Springfield, James F.; Cook, George E.; Fernandez, Kenneth R.

1990-01-01

A robot control package is described which utilizes on-line structural simulation of robot manipulators and objects in their workspace. The model-based controller is interfaced with a high level agent-independent planner, which is responsible for the task-level planning of the robot's actions. Commands received from the agent-independent planner are refined and executed in the simulated workspace, and upon successful completion, they are transferred to the real manipulators.

The Influencing Factor Analysis on the Performance Evaluation of Assembly Line Balancing Problem Level 1 (SALBP-1) Based on ANOVA Method

NASA Astrophysics Data System (ADS)

Chen, Jie; Hu, Jiangnan

2017-06-01

Industry 4.0 and lean production has become the focus of manufacturing. A current issue is to analyse the performance of the assembly line balancing. This study focus on distinguishing the factors influencing the assembly line balancing. The one-way ANOVA method is applied to explore the significant degree of distinguished factors. And regression model is built to find key points. The maximal task time (tmax ), the quantity of tasks (n), and degree of convergence of precedence graph (conv) are critical for the performance of assembly line balancing. The conclusion will do a favor to the lean production in the manufacturing.

Detection of the level of fluoride in the commercially available toothpaste using laser induced breakdown spectroscopy with the marker atomic transition line of neutral fluorine at 731.1 nm

NASA Astrophysics Data System (ADS)

Gondal, M. A.; Maganda, Y. W.; Dastageer, M. A.; Al Adel, F. F.; Naqvi, A. A.; Qahtan, T. F.

2014-04-01

Fourth harmonic of a pulsed Nd:YAG laser (wavelength 266 nm) in combination with high resolution spectrograph equipped with Gated ICCD camera has been employed to design a high sensitive analytical system. This detection system is based on Laser Induced Breakdown Spectroscopy and has been tested first time for analysis of semi-fluid samples to detect fluoride content present in the commercially available toothpaste samples. The experimental parameters were optimized to achieve an optically thin and in local thermo dynamic equilibrium plasma. This improved the limits of detection of fluoride present in tooth paste samples. The strong atomic transition line of fluorine at 731.102 nm was used as the marker line to quantify the fluoride concentration levels. Our LIBS system was able to detect fluoride concentration levels in the range of 1300-1750 ppm with a detection limit of 156 ppm.

A Bayesian-Based System to Assess Wave-Driven Flooding Hazards on Coral Reef-Lined Coasts

NASA Astrophysics Data System (ADS)

Pearson, S. G.; Storlazzi, C. D.; van Dongeren, A. R.; Tissier, M. F. S.; Reniers, A. J. H. M.

2017-12-01

Many low-elevation, coral reef-lined, tropical coasts are vulnerable to the effects of climate change, sea level rise, and wave-induced flooding. The considerable morphological diversity of these coasts and the variability of the hydrodynamic forcing that they are exposed to make predicting wave-induced flooding a challenge. A process-based wave-resolving hydrodynamic model (XBeach Non-Hydrostatic, "XBNH") was used to create a large synthetic database for use in a "Bayesian Estimator for Wave Attack in Reef Environments" (BEWARE), relating incident hydrodynamics and coral reef geomorphology to coastal flooding hazards on reef-lined coasts. Building on previous work, BEWARE improves system understanding of reef hydrodynamics by examining the intrinsic reef and extrinsic forcing factors controlling runup and flooding on reef-lined coasts. The Bayesian estimator has high predictive skill for the XBNH model outputs that are flooding indicators, and was validated for a number of available field cases. It was found that, in order to accurately predict flooding hazards, water depth over the reef flat, incident wave conditions, and reef flat width are the most essential factors, whereas other factors such as beach slope and bed friction due to the presence or absence of corals are less important. BEWARE is a potentially powerful tool for use in early warning systems or risk assessment studies, and can be used to make projections about how wave-induced flooding on coral reef-lined coasts may change due to climate change.