Identification and compensation of the temperature influences in a miniature three-axial accelerometer based on the least squares method

NASA Astrophysics Data System (ADS)

Grigorie, Teodor Lucian; Corcau, Ileana Jenica; Tudosie, Alexandru Nicolae

2017-06-01

The paper presents a way to obtain an intelligent miniaturized three-axial accelerometric sensor, based on the on-line estimation and compensation of the sensor errors generated by the environmental temperature variation. Taking into account that this error's value is a strongly nonlinear complex function of the values of environmental temperature and of the acceleration exciting the sensor, its correction may not be done off-line and it requires the presence of an additional temperature sensor. The proposed identification methodology for the error model is based on the least square method which process off-line the numerical values obtained from the accelerometer experimental testing for different values of acceleration applied to its axes of sensitivity and for different values of operating temperature. A final analysis of the error level after the compensation highlights the best variant for the matrix in the error model. In the sections of the paper are shown the results of the experimental testing of the accelerometer on all the three sensitivity axes, the identification of the error models on each axis by using the least square method, and the validation of the obtained models with experimental values. For all of the three detection channels was obtained a reduction by almost two orders of magnitude of the acceleration absolute maximum error due to environmental temperature variation.

Bale Location Effects on Nutritive Value and Fermentation Characteristics of Annual Ryegrass Bale Stored in In-line Wrapping Silage

PubMed Central

Han, K. J.; McCormick, M. E.; Derouen, S. M.; Blouin, D. C.

2014-01-01

In southeastern regions of the US, herbage systems are primarily based on grazing or hay feeding with low nutritive value warm-season perennial grasses. Nutritious herbage such as annual ryegrass (Lolium multiflorum Lam.) may be more suitable for preserving as baleage for winter feeding even with more intensive production inputs. Emerging in-line wrapped baleage storage systems featuring rapid wrapping and low polyethylene film requirements need to be tested for consistency of storing nutritive value of a range of annual ryegrass herbage. A ryegrass storage trial was conducted with 24-h wilted ‘Marshall’ annual ryegrass harvested at booting, heading and anthesis stages using three replicated in-line wrapped tubes containing ten round bales per tube. After a six-month storage period, nutritive value changes and fermentation end products differed significantly by harvest stage but not by bale location. Although wilted annual ryegrass exhibited a restricted fermentation across harvest stages characterized by high pH and low fermentation end product concentrations, butyric acid concentrations were less than 1 g/kg dry matter, and lactic acid was the major organic acid in the bales. Mold coverage and bale aroma did not differ substantially with harvest stage or bale location. Booting and heading stage-harvested ryegrass baleage were superior in nutritive value to anthesis stage-harvested herbage. Based on the investigated nutritive value and fermentation characteristics, individual bale location within in-line tubes did not significantly affect preservation quality of ryegrass round bale silages. PMID:25178371

Bale Location Effects on Nutritive Value and Fermentation Characteristics of Annual Ryegrass Bale Stored in In-line Wrapping Silage.

PubMed

Han, K J; McCormick, M E; Derouen, S M; Blouin, D C

2014-09-01

In southeastern regions of the US, herbage systems are primarily based on grazing or hay feeding with low nutritive value warm-season perennial grasses. Nutritious herbage such as annual ryegrass (Lolium multiflorum Lam.) may be more suitable for preserving as baleage for winter feeding even with more intensive production inputs. Emerging in-line wrapped baleage storage systems featuring rapid wrapping and low polyethylene film requirements need to be tested for consistency of storing nutritive value of a range of annual ryegrass herbage. A ryegrass storage trial was conducted with 24-h wilted 'Marshall' annual ryegrass harvested at booting, heading and anthesis stages using three replicated in-line wrapped tubes containing ten round bales per tube. After a six-month storage period, nutritive value changes and fermentation end products differed significantly by harvest stage but not by bale location. Although wilted annual ryegrass exhibited a restricted fermentation across harvest stages characterized by high pH and low fermentation end product concentrations, butyric acid concentrations were less than 1 g/kg dry matter, and lactic acid was the major organic acid in the bales. Mold coverage and bale aroma did not differ substantially with harvest stage or bale location. Booting and heading stage-harvested ryegrass baleage were superior in nutritive value to anthesis stage-harvested herbage. Based on the investigated nutritive value and fermentation characteristics, individual bale location within in-line tubes did not significantly affect preservation quality of ryegrass round bale silages.

Cable Overheating Risk Warning Method Based on Impedance Parameter Estimation in Distribution Network

NASA Astrophysics Data System (ADS)

Yu, Zhang; Xiaohui, Song; Jianfang, Li; Fei, Gao

2017-05-01

Cable overheating will lead to the cable insulation level reducing, speed up the cable insulation aging, even easy to cause short circuit faults. Cable overheating risk identification and warning is nessesary for distribution network operators. Cable overheating risk warning method based on impedance parameter estimation is proposed in the paper to improve the safty and reliability operation of distribution network. Firstly, cable impedance estimation model is established by using least square method based on the data from distribiton SCADA system to improve the impedance parameter estimation accuracy. Secondly, calculate the threshold value of cable impedance based on the historical data and the forecast value of cable impedance based on the forecasting data in future from distribiton SCADA system. Thirdly, establish risks warning rules library of cable overheating, calculate the cable impedance forecast value and analysis the change rate of impedance, and then warn the overheating risk of cable line based on the overheating risk warning rules library according to the variation relationship between impedance and line temperature rise. Overheating risk warning method is simulated in the paper. The simulation results shows that the method can identify the imedance and forecast the temperature rise of cable line in distribution network accurately. The result of overheating risk warning can provide decision basis for operation maintenance and repair.

Wing Infrastructure Development Outlook: Programmatic Environmental Assessment

DTIC Science & Technology

2005-07-01

supplied by TXU Electric & Gas by two transmission lines. One transmission line feeds the eastern base area and the second line feeds the western base...destruction, loss , or degradation of wetlands and to preserve and enhance the natural and beneficial values of wetlands. 1.6.3 Public Health EO 12088...action to reduce the risk of flood loss , minimize the impact of floods on human safety, health and welfare, and to restore and preserve the natural and

Graphene-based fine-tunable optical delay line for optical beamforming in phased-array antennas.

PubMed

Tatoli, Teresa; Conteduca, Donato; Dell'Olio, Francesco; Ciminelli, Caterina; Armenise, Mario N

2016-06-01

The design of an integrated graphene-based fine-tunable optical delay line on silicon nitride for optical beamforming in phased-array antennas is reported. A high value of the optical delay time (τ_g=920  ps) together with a compact footprint (4.15  mm²) and optical loss <27  dB make this device particularly suitable for highly efficient steering in active phased-array antennas. The delay line includes two graphene-based Mach-Zehnder interferometer switches and two vertically stacked microring resonators between which a graphene capacitor is placed. The tuning range is obtained by varying the value of the voltage applied to the graphene electrodes, which controls the optical path of the light propagation and therefore the delay time. The graphene provides a faster reconfigurable time and low values of energy dissipation. Such significant advantages, together with a negligible beam-squint effect, allow us to overcome the limitations of conventional RF beamformers. A highly efficient fine-tunable optical delay line for the beamsteering of 20 radiating elements up to ±20° in the azimuth direction of a tile in a phased-array antenna of an X-band synthetic aperture radar has been designed.

Effects of phase vector and history extension on prediction power of adaptive-network based fuzzy inference system (ANFIS) model for a real scale anaerobic wastewater treatment plant operating under unsteady state.

PubMed

Perendeci, Altinay; Arslan, Sever; Tanyolaç, Abdurrahman; Celebi, Serdar S

2009-10-01

A conceptual neural fuzzy model based on adaptive-network based fuzzy inference system, ANFIS, was proposed using available input on-line and off-line operational variables for a sugar factory anaerobic wastewater treatment plant operating under unsteady state to estimate the effluent chemical oxygen demand, COD. The predictive power of the developed model was improved as a new approach by adding the phase vector and the recent values of COD up to 5-10 days, longer than overall retention time of wastewater in the system. History of last 10 days for COD effluent with two-valued phase vector in the input variable matrix including all parameters had more predictive power. History of 7 days with two-valued phase vector in the matrix comprised of only on-line variables yielded fairly well estimations. The developed ANFIS model with phase vector and history extension has been able to adequately represent the behavior of the treatment system.

Improved results of LINE-1 methylation analysis in formalin-fixed, paraffin-embedded tissues with the application of a heating step during the DNA extraction process.

PubMed

Wen, Xianyu; Jeong, Seorin; Kim, Younghoon; Bae, Jeong Mo; Cho, Nam Yun; Kim, Jung Ho; Kang, Gyeong Hoon

2017-01-01

Formalin-fixed, paraffin-embedded (FFPE) tissues are important resources for profiling DNA methylation changes and for studying a variety of diseases. However, formalin fixation introduces inter-strand crosslinking, which might cause incomplete bisulfite conversion of unmethylated cytosines, which might lead to falsely elevated measurements of methylation levels in pyrosequencing assays. Long interspersed nucleotide element-1 (LINE-1) is a major constituent of repetitive transposable DNA elements, and its methylation is referred to correlates with global DNA methylation. To identify whether formalin fixation might impact the measured values of methylation in LINE-1 repetitive elements and whether prolonged heat-induced denaturation of DNA might reduce the artificial increases in measured values caused by formalin fixation, we analyzed paired fresh-frozen (FF) and FFPE xenograft tissue samples for their methylation levels in LINE-1 using a pyrosequencing assay. To further confirm the effect of a heating step in the measurement of LINE-1 or single gene methylation levels, we analyzed FFPE tissue samples of gastric cancer and colorectal cancer for their methylation status in LINE-1 and eight single genes, respectively. Formalin fixation led to an increase in the measured values of LINE-1 methylation regardless of the duration of fixation. Prolonged heating of the DNA at 95 °C for 30 min before bisulfite conversion was found (1) to decrease the discrepancy in the measured values between the paired FF and FFPE tissue samples, (2) to decrease the standard deviation of the measured value of LINE-1 methylation levels in FFPE tissue samples of gastric cancer, and (3) to improve the performance in the measurement of single gene methylation levels in FFPE tissue samples of colorectal cancer. Formalin fixation leads to artificial increases in the measured values of LINE-1 methylation, and the application of prolonged heating of DNA samples decreases the discrepancy in the measured values of LINE-1 methylation between paired FF and FFPE tissue samples. The application of prolonged heating of DNA samples improves bisulfite conversion-based measurement of LINE-1 or single gene methylation levels in FFPE tissue samples.

Dynamics of total electron content distribution during strong geomagnetic storms

NASA Astrophysics Data System (ADS)

Astafyeva, E. I.; Afraimovich, E. L.; Kosogorov, E. A.

We worked out a new method of mapping of total electron content TEC equal lines displacement velocity The method is based on the technique of global absolute vertical TEC value mapping Global Ionospheric Maps technique GIM GIM with 2-hours time resolution are available from Internet underline ftp cddisa gsfc nasa gov in standard IONEX-files format We determine the displacement velocity absolute value as well as its wave vector orientation from increments of TEC x y derivatives and TEC time derivative for each standard GIM cell 5 in longitude to 2 5 in latitude Thus we observe global traveling of TEC equal lines but we also can estimate the velocity of these line traveling Using the new method we observed anomalous rapid accumulation of the ionosphere plasma at some confined area due to the depletion of the ionization at the other spacious territories During the main phase of the geomagnetic storm on 29-30 October 2003 very large TEC enhancements appeared in the southwest of North America TEC value in that area reached up to 200 TECU 1 TECU 10 16 m -2 It was found that maximal velocity of TEC equal lines motion exceeded 1500 m s and the mean value of the velocity was about 400 m s Azimuth of wave vectors of TEC equal lines were orientated toward the center of region with anomaly high values of TEC the southwest of North America It should be noted that maximal TEC values during geomagnetically quiet conditions is about 60-80 TECU the value of TEC equal lines

Thermostability analysis of line-tension-associated nucleation at a gas-liquid interface.

PubMed

Singha, Sanat Kumar; Das, Prasanta Kumar; Maiti, Biswajit

2017-01-01

The influence of line tension on the thermostability of a droplet nucleated from an oversaturated vapor at the interface of the vapor and another immiscible liquid is investigated. Along with the condition of mechanical equilibrium, the notion of extremization of the reversible work of formation is considered to obtain the critical parameters related to heterogeneous nucleation. From the energetic formulation, the critical reversible work of formation is found to be greater than that of homogeneous nucleation for high value of the positive line tension. On the other hand, for high value of the negative line tension, the critical reversible work of formation becomes negative. Therefore, these thermodynamic instabilities under certain substrate wettability situations necessitate a free-energetics-based stability of the nucleated droplet, because the system energy is not minimized under these conditions. This thermostability is analogous to the transition-based stability proposed by Widom [B. Widom, J. Phys. Chem. 99, 2803 (1995)]10.1021/j100009a041 in the case of partial wetting phenomena along with the positive line tension. The thermostability analysis limits the domain of the solution space of the present critical-value problem as the thermodynamic transformation in connection with homogeneous and workless nucleation is considered. Within the stability range of the geometry-based wetting parameters, three limiting modes of nucleation, i.e., total-dewetting-related homogeneous nucleation, and total-wetting-associated and total-submergence-associated workless nucleation scenarios, are identified. Either of the two related limiting wetting scenarios of workless nucleation, namely, total wetting and total submergence, is found to be favorable depending on the geometry-based wetting conditions. The line-tension-associated nucleation on a liquid surface can be differentiated from that on a rigid substrate, as in the former, the stability based on mechanical equilibrium and a typical case of workless nucleation with complete submergence are observed.

On-Line Mathematics Assessment: The Impact of Mode on Performance and Question Answering Strategies

ERIC Educational Resources Information Center

Johnson, Martin; Green, Sylvia

2006-01-01

The transition from paper-based to computer-based assessment raises a number of important issues about how mode might affect children's performance and question answering strategies. In this project 104 eleven-year-olds were given two sets of matched mathematics questions, one set on-line and the other on paper. Facility values were analyzed to…

QSPR modeling: graph connectivity indices versus line graph connectivity indices

PubMed

Basak; Nikolic; Trinajstic; Amic; Beslo

2000-07-01

Five QSPR models of alkanes were reinvestigated. Properties considered were molecular surface-dependent properties (boiling points and gas chromatographic retention indices) and molecular volume-dependent properties (molar volumes and molar refractions). The vertex- and edge-connectivity indices were used as structural parameters. In each studied case we computed connectivity indices of alkane trees and alkane line graphs and searched for the optimum exponent. Models based on indices with an optimum exponent and on the standard value of the exponent were compared. Thus, for each property we generated six QSPR models (four for alkane trees and two for the corresponding line graphs). In all studied cases QSPR models based on connectivity indices with optimum exponents have better statistical characteristics than the models based on connectivity indices with the standard value of the exponent. The comparison between models based on vertex- and edge-connectivity indices gave in two cases (molar volumes and molar refractions) better models based on edge-connectivity indices and in three cases (boiling points for octanes and nonanes and gas chromatographic retention indices) better models based on vertex-connectivity indices. Thus, it appears that the edge-connectivity index is more appropriate to be used in the structure-molecular volume properties modeling and the vertex-connectivity index in the structure-molecular surface properties modeling. The use of line graphs did not improve the predictive power of the connectivity indices. Only in one case (boiling points of nonanes) a better model was obtained with the use of line graphs.

LIME: Semiautomated line measurement and identification from stellar spectra

NASA Astrophysics Data System (ADS)

Sahin, T.

2017-09-01

We present LIME (Line Measurements from ECHELLE Spectra), an IDL-based code, as a powerful tool for semiautomated stellar line measurement and identification. Interactively selected line positions (i.e. wavelengths) are compared with a master line list of the user's selections. Each unknown line that the user interactively chooses is displayed with potential identifications provided by the code in the vicinity of the selected line. The best identification is evaluated on the basis of several criteria (e.g., atomic/molecular line information, wavelength displacement, and theoretical equivalent width for solar atmospheric values). We examined the identifications by LIME in the spectra of post-red supergiant star HD 179821 over a range of signal-to-noise values and wavelength ranges. We found that the results obtained by LIME show virtually complete agreement with the manual identifications for which the conventional and also tedious approach is to use a revised multiplet table as an initial guide and perform a systematic search that makes use of the lower excitation potential and gf-values. Comparison to previous identifications for HD 179821 in the literature revealed not only lines that were unmeasurable and/or blended but also misidentifications. While a manual identification process takes a relatively longer time to be accomplished by an experienced spectroscopist, LIME can provide a rapid extraction of line information in a few hours with moderate user interaction.

Line strength measurements and relative isotopic ratio 13C/12C measurements in carbon dioxide using cavity ring down spectroscopy

NASA Astrophysics Data System (ADS)

Kiseleva, M.; Mandon, J.; Persijn, S.; Harren, F. J. M.

2018-01-01

Accurate intensity measurements were performed for several lines of the two main isotopologues of carbon dioxide, using cavity ring down spectroscopy. Absorption spectra of the R52e line at 6112.8902 cm-1 (30014←00001 band) of 12CO2 and the P6e line at 6114.8580 cm-1 (30013←00001 band) of 13CO2 were recorded at pressures between 15 and 50 mbar at 298 K. Line shape analysis shows that Galatry profile, taking into account Dicke narrowing of spectral lines, better describes the measured spectra at all pressures than the Voigt profile. The values of Dicke narrowing parameter for both lines were found to be significantly smaller than those predicted based on the mass diffusion constant. The values of the line strength for R52e line of 12CO2 and P6e line of 13CO2 were determined with an uncertainty of 0.5%. These values were found to be in good agreement with the corresponding data available in literature, in particular with the most recent ab initio calculations. The results of relative isotopic ratio 13CO2/12CO2 measurements are also presented in pure carbon dioxide samples and in 400 μmol/mol carbon dioxide in air samples, using cavity ring down spectroscopy.

A pilot study to assess feasibility of value based pricing in Cyprus through pharmacoeconomic modelling and assessment of its operational framework: sorafenib for second line renal cell cancer.

PubMed

Petrou, Panagiotis; Talias, Michael A

2014-01-01

The continuing increase of pharmaceutical expenditure calls for new approaches to pricing and reimbursement of pharmaceuticals. Value based pricing of pharmaceuticals is emerging as a useful tool and possess theoretical attributes to help health system cope with rising pharmaceutical expenditure. To assess the feasibility of introducing a value-based pricing scheme of pharmaceuticals in Cyprus and explore the integrative framework. A probabilistic Markov chain Monte Carlo model was created to simulate progression of advanced renal cell cancer for comparison of sorafenib to standard best supportive care. Literature review was performed and efficacy data were transferred from a published landmark trial, while official pricelists and clinical guidelines from Cyprus Ministry of Health were utilised for cost calculation. Based on proposed willingness to pay threshold the maximum price of sorafenib for the indication of second line renal cell cancer was assessed. Sorafenib value based price was found to be significantly lower compared to its current reference price. Feasibility of Value Based Pricing is documented and pharmacoeconomic modelling can lead to robust results. Integration of value and affordability in the price are its main advantages which have to be weighed against lack of documentation for several theoretical parameters that influence outcome. Smaller countries such as Cyprus may experience adversities in establishing and sustaining essential structures for this scheme.

Technical design and system implementation of region-line primitive association framework

NASA Astrophysics Data System (ADS)

Wang, Min; Xing, Jinjin; Wang, Jie; Lv, Guonian

2017-08-01

Apart from regions, image edge lines are an important information source, and they deserve more attention in object-based image analysis (OBIA) than they currently receive. In the region-line primitive association framework (RLPAF), we promote straight-edge lines as line primitives to achieve powerful OBIAs. Along with regions, straight lines become basic units for subsequent extraction and analysis of OBIA features. This study develops a new software system called remote-sensing knowledge finder (RSFinder) to implement RLPAF for engineering application purposes. This paper introduces the extended technical framework, a comprehensively designed feature set, key technology, and software implementation. To our knowledge, RSFinder is the world's first OBIA system based on two types of primitives, namely, regions and lines. It is fundamentally different from other well-known region-only-based OBIA systems, such as eCogntion and ENVI feature extraction module. This paper has important reference values for the development of similarly structured OBIA systems and line-involved extraction algorithms of remote sensing information.

An In Vivo Evaluation of the Fit of Zirconium-Oxide Based, Ceramic Single Crowns with Vertical and Horizontal Finish Line Preparations.

PubMed

Vigolo, Paolo; Mutinelli, Sabrina; Biscaro, Leonello; Stellini, Edoardo

2015-12-01

Different types of tooth preparations influence the marginal precision of zirconium-oxide based ceramic single crowns. In this in vivo study, the marginal fits of zirconium-oxide based ceramic single crowns with vertical and horizontal finish lines were compared. Forty-six teeth were chosen in eight patients indicated for extraction for implant placement. CAD/CAM technology was used for the production of 46 zirconium-oxide-based ceramic single crowns: 23 teeth were prepared with vertical finishing lines, 23 with horizontal finishing lines. One operator accomplished all clinical procedures. The zirconia crowns were cemented with glass ionomer cement. The teeth were extracted 1 month later. Marginal gaps along vertical planes were measured for each crown, using a total of four landmarks for each tooth by means of a microscope at 50× magnification. On conclusion of microscopic assessment, ESEM evaluation was completed on all specimens. The comparison of the gap between the two types of preparation was performed with a nonparametric test (two-sample Wilcoxon rank-sum test) with a level of significance fixed at p < 0.05. All data were analyzed with STATA12. In the group with horizontal finish line preparations, the median value of the gap was 35.45 μm (Iqr, 0.33); for the vertical finish line group, the median value of the gap was 35.44 μm (Iqr, 0.40). The difference between the two groups was not statistically significant (two-sample Wilcoxon rank-sum test, p = 0.0872). Within the limitations of this study, the gaps of the zirconium-oxide-based ceramic CAD/CAM crowns with vertical and horizontal finish line preparations were not different. © 2015 by the American College of Prosthodontists.

High Sensitivity Absorption Spectroscopy on Ti II VUV Resonance Lines of Astrophysical Interest

NASA Astrophysics Data System (ADS)

Wiese, Lm; Fedchak, Ja; Lawler, Je

2000-06-01

The neutral hydrogen regions of the Interstellar Medium (ISM) of our Galaxy and distant galaxies produce simple absorption spectra because most metals are singly ionized and in their ground fine structure level. Elemental abundance measurements and other studies of the ISM rely on accurate atomic oscillator strengths (f-values) for a few key lines in the second spectra of Ti and other metals. The Ti II VUV resonance lines at 1910.6 and 1910.9 Åare important in absorption line systems in which quasars provide the continuum and the ISM of intervening galaxies is observed. Some of these absorption line systems are redshifted to the visible and observed with ground based telescopes. We report the first laboratory measurement of these Ti II VUV resonance lines. Using High Sensitivity Absorption Spectroscopy, we determined f-values for the 1910 Ålines relative to well-known Ti II resonance lines at 3067 and 3384 ÅContinuum radiation from an Aladdin Storage Ring bending magnet at the Synchrotron Radiation Center (SRC) is passed through a discharge plasma containing Ti^+. The transmitted light is analyzed by our 3m vacuum echelle spectrometer equipped with VUV sensitive CCD array. The resolving power of our spectrometer/detector array is 300,000. F-values are determined to within 10%.

The Power Behind the Controversy: Understanding Local Policy Elites' Perceptions on the Benefits and Risks Associated with High Voltage Power Line Installation in the State of Arkansas

NASA Astrophysics Data System (ADS)

Moyer, Rachael M.

Following a proposal for the installation of high voltage power lines in northwest Arkansas, a controversial policy debate emerged. Proponents of the transmission line argue that such an installation is inevitable and necessary to efficiently and reliably support the identified electric load in the region. Opponents claim that the lines will degrade the natural environment and hamper the tourism-based local economy in affected regions, notably in Ozark Mountain areas. This study seeks to understand how local policy elites perceive the benefits and risks associated with proposed transmission lines, which is a critical step in comprehending the formation and changes of related government policies. First, based upon the dual process theory of judgment, this study systematically investigates the triadic relationships between (a) more profound personal value predispositions, (b) affects and feelings, and (c) perceived benefits and risks related to the proposed installation of high voltage power lines among local policy elites in the state of Arkansas. Next, this study focuses more specifically on the role of value predispositions, specific emotional dimensions of affect heuristics, and perceptions pertaining to high voltage power line risks and benefits. Using original data collected from a statewide Internet survey of 420 local leaders and key policymakers about their opinions on the related issues, other factors claimed by previous literature, including trust, knowledge level, and demographic characteristics are considered. Analytical results suggest that grid-group cultural predispositions, as deeply held core values within local policy elites' individual belief systems, both directly and indirectly -- through affective feelings -- shape perceived utility associated with the installation of high voltage power lines. Recognizing that risk perceptions factor into policy decisions, some practical considerations for better designing policy addressing controversial issues of this nature.

Multi-modal management of acromegaly: a value perspective.

PubMed

Kimmell, Kristopher T; Weil, Robert J; Marko, Nicholas F

2015-10-01

The Acromegaly Consensus Group recently released updated guidelines for medical management of acromegaly patients. We subjected these guidelines to a cost analysis. We conducted a cost analysis of the recommendations based on published efficacy rates as well as publicly available cost data. The results were compared to findings from a previously reported comparative effectiveness analysis of acromegaly treatments. Using decision tree software, two models were created based on the Acromegaly Consensus Group's recommendations and the comparative effectiveness analysis. The decision tree for the Consensus Group's recommendations was subjected to multi-way tornado analysis to identify variables that most impacted the value analysis of the decision tree. The value analysis confirmed the Consensus Group's recommendations of somatostatin analogs as first line therapy for medical management. Our model also demonstrated significant value in using dopamine agonist agents as upfront therapy as well. Sensitivity analysis identified the cost of somatostatin analogs and growth hormone receptor antagonists as having the most significant impact on the cost effectiveness of medical therapies. Our analysis confirmed the value of surgery as first-line therapy for patients with surgically accessible lesions. Surgery provides the greatest value for management of patients with acromegaly. However, in accordance with the Acromegaly Consensus Group's recent recommendations, somatostatin analogs provide the greatest value and should be used as first-line therapy for patients who cannot be managed surgically. At present, the substantial cost is the most significant negative factor in the value of medical therapies for acromegaly.

The Tai Chi in Star Formation

NASA Astrophysics Data System (ADS)

Li, Hua-bai

2017-10-01

Tai Chi, a Chinese martial art developed based on the laws of nature, emphasises how 'to conquer the unyielding with the yielding'. The recent observation of star formation shows that stars result from the interaction between gravity, turbulence and magnetic fields. This interaction again follows the nature rules that inspired Tai Chi. For example, if self-gravity is the force that dominates, the molecular cloud will collapse isotropically, which compresses magnetic field lines. The density of the yielding field lines increases until magnetic pressure reaches the critical value to support the cloud against the gravitational force in directions perpendicular to the field lines (Lorentz force). Then gravity gives way to Lorentz force, accumulating gas only along the field lines till the gas density achieves the critical value to again compress the field lines. The Tai Chi goes on in a self-similar way.

Continuous quality improvement programs provide new opportunities to drive value innovation initiatives in hospital-based radiology practices.

PubMed

Steele, Joseph R; Schomer, Don F

2009-07-01

Imaging services constitute a huge portion of the of the total dollar investment within the health care enterprise. Accordingly, this generates competition among medical specialties organized along service lines for their pieces of the pie and increased scrutiny from third-party payers and government regulators. These market and political forces create challenge and opportunity for a hospital-based radiology practice. Clearly, change that creates or builds greater value for patients also creates sustainable competitive advantage for a radiology practice. The somewhat amorphous concept of quality constitutes a significant value driver for innovation in this scenario. Quality initiatives and programs seek to define and manage this amorphous concept and provide tools for a radiology practice to create or build more value. Leadership and the early adoption of these inevitable programs by a radiology practice strengthens relationships with hospital partners and slows the attrition of imaging service lines to competitors.

Supraorbital Keyhole Craniotomy for Basilar Artery Aneurysms: Accounting for the "Cliff" Effect.

PubMed

Stamates, Melissa M; Wong, Andrew K; Bhansali, Anita; Wong, Ricky H

2017-04-01

Treatment of basilar artery aneurysms is challenging. While endovascular techniques have dominated, there still remain circumstances where open surgical clipping is required or preferred. Minimally invasive "keyhole" approaches are being used more frequently to provide the durability of surgical clipping with a lower morbidity profile; however, careful patient selection is required. The supraorbital "keyhole" approach has been described for the treatment of basilar artery aneurysms, but careful assessment of the basilar exposure is necessary to ensure proper visualization of the aneurysm and ability to obtain proximal vascular control. Various methods of estimating the basilar artery exposure in this approach have been described, including the anterior skull base line and the posterior clinoid line, but both are unreliable and inaccurate. To propose a new method, the orbital roof-dorsum line, to simply and accurately predict the basilar artery exposure. CT angiograms for 20 consecutive unique patients were analyzed to obtain the anterior skull base line, posterior clinoid line, and the orbital roof-dorsum line. CT angiograms were then loaded onto a Stealth neuronavigation system (Medtronic, Minneapolis, Minnesota) to obtain "true" visualization lengths. A case illustration is presented. Pairwise comparison tests demonstrated that both the anterior skull base and the posterior clinoid estimation lines differed significantly from the "true"  value ( P < .0001). Our orbital roof-dorsum estimation provided results that accurately predicted the "true" value ( P = .71). The orbital roof-dorsum line provides a simple and reliable method of estimating basilar artery exposure and should be used whenever considering patients for surgical clipping by this approach. Copyright © 2017 by the Congress of Neurological Surgeons

Intensity of emission lines of the quiescent solar corona: comparison between calculated and observed values

NASA Astrophysics Data System (ADS)

Krissinel, Boris

2018-03-01

The paper reports the results of calculations of the center-to-limb intensity of optically thin line emission in EUV and FUV wavelength ranges. The calculations employ a multicomponent model for the quiescent solar corona. The model includes a collection of loops of various sizes, spicules, and free (inter-loop) matter. Theoretical intensity values are found from probabilities of encountering parts of loops in the line of sight with respect to the probability of absence of other coronal components. The model uses 12 loops with sizes from 3200 to 210000 km with different values of rarefaction index and pressure at the loop base and apex. The temperature at loop apices is 1 400 000 K. The calculations utilize the CHIANTI database. The comparison between theoretical and observed emission intensity values for coronal and transition region lines obtained by the SUMER, CDS, and EIS telescopes shows quite satisfactory agreement between them, particularly for the solar disk center. For the data acquired above the limb, the enhanced discrepancies after the analysis refer to errors in EIS measurements.

Improving the performance of a filling line based on simulation

NASA Astrophysics Data System (ADS)

Jasiulewicz-Kaczmarek, M.; Bartkowiak, T.

2016-08-01

The paper describes the method of improving performance of a filling line based on simulation. This study concerns a production line that is located in a manufacturing centre of a FMCG company. A discrete event simulation model was built using data provided by maintenance data acquisition system. Two types of failures were identified in the system and were approximated using continuous statistical distributions. The model was validated taking into consideration line performance measures. A brief Pareto analysis of line failures was conducted to identify potential areas of improvement. Two improvements scenarios were proposed and tested via simulation. The outcome of the simulations were the bases of financial analysis. NPV and ROI values were calculated taking into account depreciation, profits, losses, current CIT rate and inflation. A validated simulation model can be a useful tool in maintenance decision-making process.

Chromospheric and Transition region He lines during a flare

NASA Astrophysics Data System (ADS)

Falchi, A.; Mauas, P. J. D.; Andretta, V.; Teriaca, L.; Cauzzi, G.; Falciani, R.; Smaldone, L. A.

An observing campaign (SOHO JOP 139), coordinated between ground based and SOHO instruments, has been planned to obtain simultaneous spectroheliograms of the same area in several spectral lines. The chromospheric lines Ca II K, Hα and Na I D as well as He I 10830, 5876, 584 and 304 Ålines have been observed. These observations allow us to build semi-empirical models of the atmosphere before and during a small flare. With these models, constructed to match the observed line profiles, we can test the He abundance value.

A pilot study to assess feasibility of value based pricing in Cyprus through pharmacoeconomic modelling and assessment of its operational framework: sorafenib for second line renal cell cancer

PubMed Central

2014-01-01

Background The continuing increase of pharmaceutical expenditure calls for new approaches to pricing and reimbursement of pharmaceuticals. Value based pricing of pharmaceuticals is emerging as a useful tool and possess theoretical attributes to help health system cope with rising pharmaceutical expenditure. Aim To assess the feasibility of introducing a value-based pricing scheme of pharmaceuticals in Cyprus and explore the integrative framework. Methods A probabilistic Markov chain Monte Carlo model was created to simulate progression of advanced renal cell cancer for comparison of sorafenib to standard best supportive care. Literature review was performed and efficacy data were transferred from a published landmark trial, while official pricelists and clinical guidelines from Cyprus Ministry of Health were utilised for cost calculation. Based on proposed willingness to pay threshold the maximum price of sorafenib for the indication of second line renal cell cancer was assessed. Results Sorafenib value based price was found to be significantly lower compared to its current reference price. Conclusion Feasibility of Value Based Pricing is documented and pharmacoeconomic modelling can lead to robust results. Integration of value and affordability in the price are its main advantages which have to be weighed against lack of documentation for several theoretical parameters that influence outcome. Smaller countries such as Cyprus may experience adversities in establishing and sustaining essential structures for this scheme. PMID:24910539

New biotite and muscovite isotopic reference materials, USGS57 and USGS58, for δ2H measurements–A replacement for NBS 30

USGS Publications Warehouse

Qi, Haiping; Coplen, Tyler B.; Gehre, Matthias; Vennemann, Torsten W.; Brand, Willi A.; Geilmann, Heike; Olack, Gerard; Bindeman, Ilya N.; Palandri, Jim; Huang, Li; Longstaffe, Fred J.

2017-01-01

The advent of continuous-flow isotope-ratio mass spectrometry (CF-IRMS) coupled with a high temperature conversion (HTC) system enabled faster, more cost effective, and more precise δ2H analysis of hydrogen-bearing solids. Accurate hydrogen isotopic analysis by on-line or off-line techniques requires appropriate isotopic reference materials (RMs). A strategy of two-point calibrations spanning δ2H range of the unknowns using two RMs is recommended. Unfortunately, the supply of the previously widely used isotopic RM, NBS 30 biotite, is exhausted. In addition, recent measurements have shown that the determination of δ2H values of NBS 30 biotite on the VSMOW-SLAP isotope-delta scale by on-line HTC systems with CF-IRMS may be unreliable because hydrogen in this biotite may not be converted quantitatively to molecular hydrogen. The δ2HVSMOW-SLAP values of NBS 30 biotite analyzed by on-line HTC systems can be as much as 21 mUr (or ‰) too positive compared to the accepted value of − 65.7 mUr, determined by only a few conventional off-line measurements. To ensure accurate and traceable on-line hydrogen isotope-ratio determinations in mineral samples, we here propose two isotopically homogeneous, hydrous mineral RMs with well-characterized isotope-ratio values, which are urgently needed. The U.S. Geological Survey (USGS) has prepared two such RMs, USGS57 biotite and USGS58 muscovite. The δ2H values were determined by both glassy carbon-based on-line conversion and chromium-based on-line conversion, and results were confirmed by off-line conversion. The quantitative conversion of hydrogen from the two RMs using the on-line HTC method was carefully evaluated in this study. The isotopic compositions of these new RMs with 1-σ uncertainties and mass fractions of hydrogen are:USGS57 (biotite)δ2HVSMOW-SLAP = − 91.5 ± 2.4 mUr (n = 24)Mass fraction hydrogen = 0.416 ± 0.002% (n = 4)Mass fraction water = 3.74 ± 0.02% (n = 4)USGS58 (muscovite)δ2HVSMOW-SLAP = − 28.4 ± 1.6 mUr (n = 24)Mass fraction hydrogen = 0.448 ± 0.002% (n = 4)Mass fraction water = 4.03 ± 0.02% (n = 4).These δ2HVSMOW-SLAP values encompass typical ranges for solid unknowns of crustal and mantle origin and are available to users for recommended two-point calibration.

The new on-line Czech Food Composition Database.

PubMed

Machackova, Marie; Holasova, Marie; Maskova, Eva

2013-10-01

The new on-line Czech Food Composition Database (FCDB) was launched on http://www.czfcdb.cz in December 2010 as a main freely available channel for dissemination of Czech food composition data. The application is based on a complied FCDB documented according to the EuroFIR standardised procedure for full value documentation and indexing of foods by the LanguaL™ Thesaurus. A content management system was implemented for administration of the website and performing data export (comma-separated values or EuroFIR XML transport package formats) by a compiler. Reference/s are provided for each published value with linking to available freely accessible on-line sources of data (e.g. full texts, EuroFIR Document Repository, on-line national FCDBs). LanguaL™ codes are displayed within each food record as searchable keywords of the database. A photo (or a photo gallery) is used as a visual descriptor of a food item. The application is searchable on foods, components, food groups, alphabet and a multi-field advanced search. Copyright © 2013 Elsevier Ltd. All rights reserved.

IMPROVED V I log(gf) VALUES AND ABUNDANCE DETERMINATIONS IN THE PHOTOSPHERES OF THE SUN AND METAL-POOR STAR HD 84937

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawler, J. E.; Wood, M. P.; Den Hartog, E. A.

2015-01-01

New emission branching fraction measurements for 836 lines of the first spectrum of vanadium (V I) are determined from hollow cathode lamp spectra recorded with the National Solar Observatory 1 m Fourier transform spectrometer (FTS) and a high-resolution echelle spectrometer. The branching fractions are combined with recently published radiative lifetimes from laser-induced fluorescence measurements to determine accurate absolute atomic transition probabilities for the 836 lines. The FTS data are also used to extract new hyperfine structure A coefficients for 26 levels of neutral vanadium. These new laboratory data are applied to determine the V abundance in the Sun and metal-poormore » star HD 84937, yielding log ε(V) = 3.956 ± 0.004 (σ = 0.037) based on 93 V I lines and log ε(V) = 1.89 ± 0.03 (σ = 0.07) based on nine V I lines, respectively, using the Holweger-Müller 1D model. These new V I abundance values for the Sun and HD 84937 agree well with our earlier determinations based upon V II.« less

The Study of Axiological Orientations of Kazakh Diaspora, Living Abroad

ERIC Educational Resources Information Center

Sakhiyeva, Farida A.; Berdibayeva, Sveta K.; Kasymova, Roza S.; Shagyrbayeva, Mentay; Smatova, Clara B.; Orazbayeva, Ayimbala Sh.

2016-01-01

Considers the lines of development for ethnic-national values as the driving force of the Kazakh nation's multiethnic society, characterizes ethnic and national value orientations inherent in the representatives of the Kazakh nation based on a comparison of value orientations of Kazakh living in Kazakhstan and abroad, determines the dominating…

Synthesis of mono Mannich bases of 2-(4-hydroxybenzylidene)-2,3-dihydroinden-1-one and evaluation of their cytotoxicities.

PubMed

Tugrak, Mehtap; Yamali, Cem; Sakagami, Hiroshi; Gul, Halise Inci

2016-10-01

Chalcones and Mannich bases are a group of compounds known for their cytotoxicities. In this study restricted chalcone analogue, compound 2-(4-hydroxybenzylidene)-2,3-dihydroinden-1-one MT1, was used as a starting compound to synthesize new mono Mannich bases since Mannich bases may induce more cytotoxicity than chalcone analogue that they are derived from by producing additional alkylating center for cellular thiols. In this study, cyclic and acyclic amines were used to synthesize Mannich bases. All compounds were tested against Ca9-22 (gingival carcinoma), HSC-2, HSC-3 and HSC-4 (oral squamous cell carcinoma) as tumour cell lines and HGF (gingival fibroblasts), HPC (pulp cells) and HPLF (periodontal ligament fibroblasts) human normal oral cells as non tumour cell lines. Cytotoxicity, selectivity index (SI) values and potency selectivity expression (PSE) values expressed as a percentage were determined for the compounds. According to data obtained, the compound MT8 with the highest PSE value bearing N-methylpiperazine moiety seems to be a good candidate to develop new cytotoxic compounds and is suited for further investigation.

Synthesis and antiproliferative activity of imidazo[1,2-a]pyrimidine Mannich bases.

PubMed

Aeluri, Raghunath; Alla, Manjula; Polepalli, Sowjanya; Jain, Nishant

2015-07-15

A series of imidazo[1,2-a]pyrimidine Mannich bases were designed, synthesized in two phases. Mannich bases were obtained by one pot three component condensation of imidazo[1,2-a]pyrimidine with secondary amine or piperazine and excess of formaldehyde solution in methanol. The synthesized Mannich bases were screened for in vitro growth inhibition against a panel of 3 different human cancer cell lines. Most of the synthesized compounds exhibited antiproliferative activity with GI50 values ranging from 0.01 to 79.4 μM. Compounds 5e, 6b and 7k were found to be effective inhibitors of growth of all cell lines, with GI50 values similar to that of standard drug. The structure and activity relationship has been disclosed. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Meta-heuristic algorithm to solve two-sided assembly line balancing problems

NASA Astrophysics Data System (ADS)

Wirawan, A. D.; Maruf, A.

2016-02-01

Two-sided assembly line is a set of sequential workstations where task operations can be performed at two sides of the line. This type of line is commonly used for the assembly of large-sized products: cars, buses, and trucks. This paper propose a Decoding Algorithm with Teaching-Learning Based Optimization (TLBO), a recently developed nature-inspired search method to solve the two-sided assembly line balancing problem (TALBP). The algorithm aims to minimize the number of mated-workstations for the given cycle time without violating the synchronization constraints. The correlation between the input parameters and the emergence point of objective function value is tested using scenarios generated by design of experiments. A two-sided assembly line operated in an Indonesia's multinational manufacturing company is considered as the object of this paper. The result of the proposed algorithm shows reduction of workstations and indicates that there is negative correlation between the emergence point of objective function value and the size of population used.

Uncertainties Associated with Theoretically Calculated N2-Broadened Half-Widths of H2O Lines

NASA Technical Reports Server (NTRS)

Ma, Q.; Tipping, R. H.; Gamache, R. R.

2010-01-01

With different choices of the cut-offs used in theoretical calculations, we have carried out extensive numerical calculations of the N2-broadend Lorentzian half-widths of the H2O lines using the modified Robert-Bonamy formalism. Based on these results, we are able to thoroughly check for convergence. We find that, with the low-order cut-offs commonly used in the literature, one is able to obtain converged values only for lines with large half-widths. Conversely, for lines with small half-widths, much higher cut-offs are necessary to guarantee convergence. We also analyse the uncertainties associated with calculated half-widths, and these are correlated as above. In general, the smaller the half-widths, the poorer the convergence and the larger the uncertainty associated with them. For convenience, one can divide all H2O lines into three categories, large, intermediate, and small, according to their half-width values. One can use this division to judge whether the calculated half-widths are converged or not, based on the cut-offs used, and also to estimate how large their uncertainties are. We conclude that with the current Robert- Bonamy formalism, for lines in category lone can achieve the accuracy requirement set by HITRAN, whereas for lines in category 3, it 'is impossible to meet this goal.

Fred Hutchinson Cancer Research Center (FHCRC-1): Functional Exploration of the Druggable Genome in MYCN Amplified and Non-amplified Neuroblastoma | Office of Cancer Genomics

Cancer.gov

To identify candidate drugs targets for neuroblastoma with MYCN amplification we performed parallel siRNA screens with a druggable genome collection of ~6,700 genes comparing MYCN amplified and non-MYCN amplified cell lines: SK-N-BE2 (MYCN amplified) and SK-N-AS (non amplified).  The Hits from each cell lines were determined based on their significance with respect to their differential activity in the presence or absence of RA within each cell line.  Hits for each cell line were also ranked according to their P-value, based on the three replicates.  Integration with gene exp

Fred Hutchinson Cancer Research Center (FHCRC-1): Functional Exploration of the Druggable Genome in MYCN Amplified and Non-amplified Neuroblastoma | Office of Cancer Genomics

Cancer.gov

To identify candidate drugs targets for neuroblastoma with MYCN amplification we performed parallel siRNA screens with a druggable genome collection of ~6,700 genes comparing MYCN amplified and non-MYCN amplified cell lines: SK-N-BE2 (MYCN amplified) and SK-N-AS (non amplified). The Hits from each cell lines were determined based on their significance with respect to their differential activity in the presence or absence of RA within each cell line. Hits for each cell line were also ranked according to their P-value, based on the three replicates. Integration with gene expres

The method for measuring the groove density of variable-line-space gratings with elimination of the eccentricity effect

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Qingbo; Liu, Zhengkun, E-mail: zhkliu@ustc.edu.cn; Chen, Huoyao

2015-02-15

To eliminate the eccentricity effect, a new method for measuring the groove density of a variable-line-space grating was adapted. Based on grating equation, groove density is calculated by measuring the internal angles between zeroth-order and first-order diffracted light for two different wavelengths with the same angle of incidence. The measurement system mainly includes two laser sources, a phase plate, plane mirror, and charge coupled device. The measurement results of a variable-line-space grating demonstrate that the experiment data agree well with theoretical values, and the value of measurement error (ΔN/N) is less than 2.72 × 10{sup −4}.

78 FR 8195 - Biweekly Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-05

... of the bases for the contention and a concise statement of the alleged facts or expert opinion which..., ``Allowable Value for Primary Containment and Drywell Isolation Instrumentation,'' Function 3.c, ``Reactor Core Isolation Cooling (RCIC) Steam Supply Line Pressure--Low.'' This TS allowable value will be...

A gradient-based approach for automated crest-line detection and analysis of sand dune patterns on planetary surfaces

NASA Astrophysics Data System (ADS)

Lancaster, N.; LeBlanc, D.; Bebis, G.; Nicolescu, M.

2015-12-01

Dune-field patterns are believed to behave as self-organizing systems, but what causes the patterns to form is still poorly understood. The most obvious (and in many cases the most significant) aspect of a dune system is the pattern of dune crest lines. Extracting meaningful features such as crest length, orientation, spacing, bifurcations, and merging of crests from image data can reveal important information about the specific dune-field morphological properties, development, and response to changes in boundary conditions, but manual methods are labor-intensive and time-consuming. We are developing the capability to recognize and characterize patterns of sand dunes on planetary surfaces. Our goal is to develop a robust methodology and the necessary algorithms for automated or semi-automated extraction of dune morphometric information from image data. Our main approach uses image processing methods to extract gradient information from satellite images of dune fields. Typically, the gradients have a dominant magnitude and orientation. In many cases, the images have two major dominant gradient orientations, for the sunny and shaded side of the dunes. A histogram of the gradient orientations is used to determine the dominant orientation. A threshold is applied to the image based on gradient orientations which agree with the dominant orientation. The contours of the binary image can then be used to determine the dune crest-lines, based on pixel intensity values. Once the crest-lines have been extracted, the morphological properties can be computed. We have tested our approach on a variety of images of linear and crescentic (transverse) dunes and compared dune detection algorithms with manually-digitized dune crest lines, achieving true positive values of 0.57-0.99; and false positives values of 0.30-0.67, indicating that out approach is generally robust.

Identification of Sungai Batu Sediment using 2-D Resistivity Imaging and Seismic Refraction Methods for Ancient River Mapping at Kedah, Malaysia

NASA Astrophysics Data System (ADS)

Andika, F.; Saad, R.; Saidin, M. M.; Muztaza, N. M.; Amsir

2018-04-01

Sungai Batu is an earliest civilization in Southeast Asia with evidenced by the discovery of riverside jetty, iron smelting, and ritual monuments. The evidences can lead to prediction of buried river caused by geological and sedimentation process. This study was conducted to study sediment deposit characteristic and to map thickness of the sediments using 2-D resistivity imaging and seismic refraction for ancient river mapping. A total of thirty, 2-D resistivity and nine seismic survey lines were conducted at the study area. Four of the lines R1-R4 and S1-S4 were correlated and validated with existing on site boreholes BH1-BH4 to identify sediment type and thickness. The validated values applied to the remaining survey lines which no borehole record to map the subsurface of the study area. Based on the results, Sungai Batu area consist of clay with resistivity value of 6.6-25.9 Ω.m and velocity value of 716.9-1606.9 m/s; sandy clay with resistivity value of 6-265.1 Ω.m and velocity value of 1003.6-1901.4 m/s; while shale was identified with resistivity value of >668.6 Ω.m and velocity value of >2051.7 m/s. Boundary between clay/sandy clay with shale was identified with resistivity value of 314 Ω.m and velocity value of 1822 m/s. The integration of the 2-D resistivity and seismic refraction identified that the thickness of Sungai Batu sediment is 0-150 m and Sungai Batu ancient river was successfully map based on thickness of sediment which is >45 m.

Complex approach to the investigation of short fiber-optic comunication lines

NASA Astrophysics Data System (ADS)

Sukhoivanov, I. A.; Kontar', A. A.; Kublik, A. V.; Makarevich, V. S.

The paper proposes a method of complex measurements based on the consideration of the parameters of all the elements used in a specific multimode fiber-optic communication line. It is shown that the error in measuring losses in waveguides up to 20 m long can reach a value of 60 percent.

Cephalometrically assessing the validity of superior, middle and inferior tragus points on ala-tragus line while establishing the occlusal plane in edentulous patient

PubMed Central

Thombare, Ram

2013-01-01

PURPOSE The purpose of this study was to decide the most appropriate point on tragus to be used as a reference point at time of marking ala tragus line while establishing occlusal plane. MATERIALS AND METHODS The data was collected in two groups of subjects: 1) Dentulous 2) Edentulous group having sample size of 30 for each group with equal gender distribution (15 males, 15 females each). Downs analysis was used for base value. Lateral cephalographs were taken for all selected subjects. Three points were marked on tragus as Superior (S), Middle (M), and Inferior (I) and were joined with ala (A) of the nose to form ala-tragus lines. The angle formed by each line (SA plane, MA plane, IA plane) with Frankfort Horizontal (FH) plane was measured by using custom made device and modified protractor in all dentulous and edentulous subjects. Also, in dentulous subjects angle between Frankfort Horizontal plane and natural occlusal plane was measured. The measurements obtained were subjected to the following statistical tests; descriptive analysis, Student's unpaired t-test and Pearson's correlation coefficient. RESULTS The results demonstrated, the mean angle COO (cant of occlusal plane) as 9.76°, inferior point on tragus had given the mean angular value of IFH [Angle between IA plane (plane formed by joining inferior point-I on tragus and ala of nose- A) and FH plane) as 10.40° and 10.56° in dentulous and edentulous subjects respectively which was the closest value to the angle COO and was comparable with the values of angle COO value in Downs analysis. Angulations of ala-tragus line marked from inferior point with occlusal plane in dentulous subject had given the smallest value 2.46° which showed that this ala-tragus line was nearly parallel to occlusal plane. CONCLUSION The inferior point marked on tragus is the most appropriate point for marking ala-tragus line. PMID:23508068

Measurement value analysis overall equipment effectiveness (OEE) packaging process in line 2 (Case Study of PT. MBI Tbk)

NASA Astrophysics Data System (ADS)

Rimawan, Erry; Kholil, Muhammad; Hendri

2018-03-01

PT. MBI Tbk is engaged in the manufacture of beverage industry, where the company’s production is based on the magnitude of customer demand that is marketing offices that had been scattered in various regions of Indonesia. In the packaging process steps in PT.MBI through the line 3 lines including racking, canning line, bottling line. In the canning process to existing packing on Line 2 (canning line), there are some machines that are used continuously, among other Depalletizer machine, filler machine, can seamer machine, pasteurizer machine, machine FLD, Wrap Around engine, engine Shrink Wrap. Due to the large demand from customers that is relentless, therefore the calculation of overall equipment effectiveness (OEE) as a whole on line 2 (canning line) is needed in order to make improvements continuously (Continuous Improvement) at line 2 (canning line). This study aims to determine the value of overall equipment effectiveness (OEE) and Losses of the most influential of the big six OEE Losses focused on equipment or machinery as a whole into a single unit that is on the line 2, which will then be known root cause of the losses that occur from the research over the field. From the calculation of overall equipment effectiveness (OEE), there are two ratios are still poor and under world-class standards, while the ratio of the availability of 88.85% of the world-class standards by 90% and the performance ratio of 78.51% of the standard world class by 95%, whereas for quality ratio has entered the world-class standard that is equal to 99.90%. Thus the value of OEE on Line 2 line is below world class standards. In this study there were only five losses, which can be identified, and while the losses were very influential, namely the Speed Reduced Losses, losses, these losses accounted for the largest percentage of the value of the rate of 19.12%, of the results of this study losses occurred due to poor surveillance systems (less good) that causes the employee or operator does not perform the work in accordance with a predetermined.

The expected value of possession in professional rugby league match-play.

PubMed

Kempton, Thomas; Kennedy, Nicholas; Coutts, Aaron J

2016-01-01

This study estimated the expected point value for starting possessions in different field locations during rugby league match-play and calculated the mean expected points for each subsequent play during the possession. It also examined the origin of tries scored according to the method of gaining possession. Play-by-play data were taken from all 768 regular-season National Rugby League (NRL) matches during 2010-2013. A probabilistic model estimated the expected point outcome based on the net difference in points scored by a team in possession in a given situation. An iterative method was used to approximate the value of each situation based on actual scoring outcomes. Possessions commencing close to the opposition's goal-line had the highest expected point equity, which decreased as the location of the possession moved towards the team's own goal-line. Possessions following an opposition error, penalty or goal-line dropout had the highest likelihood of a try being scored on the set subsequent to their occurrence. In contrast, possessions that follow an opposition completed set or a restart were least likely to result in a try. The expected point values framework from our model has applications for informing playing strategy and assessing individual and team performance in professional rugby league.

Laboratory measurements of VUV N2 photoabsorption cross sections and line widths: applications to planetary atmospheric transmission models

NASA Astrophysics Data System (ADS)

Smith, P. L.; Stark, G.; Yoshino, K.

2003-05-01

The analyses of VUV occultation measurements of the N2-rich atmospheres of Titan and Triton are hampered by the lack of fundamental spectroscopic data for N2. There is a need for reliable photoabsorption cross sections and line widths for the 100 electronic bands of N2 in the 80 to 100 nm wavelength region. We present analyses of new measurements of individual line strengths and widths in N2 bands in the region 94 to 100 nm. Within individual bands, we find significant departures from the predicted line strength distributions based on isolated band models. Line width analyses within each band indicate that predissociation-broadening is often highly dependent on the rotational quantum number. We illustrate the importance of N2 line widths in the analysis of occultation measurements via N2 transmission models over selected wavelength regions. We have continued to compile on-line molecular spectroscopic atlas based on our N2 laboratory data: http://cfa-www.harvard.edu/amdata/ampdata/N2ARCHIVE/n2home.html. The archive includes published and unpublished 14N2, 14N15N, and 15N2 line lists and spectroscopic identifications, excited state energy levels, band and line f-values, a summary of published band f-value and line width measurements, and a cross-referenced summary of the relevant N2 literature. The listings are searchable by wavelength interval or band identification and are suitable for down-loading in a convenient format. We gratefully acknowledge funding support from NASA grant NAG5-9059 and the Smithsonian Institution Atherton-Seidell Grant Program.

Evaluation of toxicity and biodegradability of choline chloride based deep eutectic solvents.

PubMed

Radošević, Kristina; Bubalo, Marina Cvjetko; Srček, Višnje Gaurina; Grgas, Dijana; Dragičević, Tibela Landeka; Redovniković, Ivana Radojčić

2015-02-01

Deep eutectic solvents (DESs) have been dramatically expanding in popularity as a new generation of environmentally friendly solvents with possible applications in various industrial fields, but their ecological footprint has not yet been thoroughly investigated. In the present study, three choline chloride-based DESs with glucose, glycerol and oxalic acid as hydrogen bond donors were evaluated for in vitro toxicity using fish and human cell line, phytotoxicity using wheat and biodegradability using wastewater microorganisms through closed bottle test. Obtained in vitro toxicity data on cell lines indicate that choline chloride: glucose and choline chloride:glycerol possess low cytotoxicity (EC50>10 mM for both cell lines) while choline chloride:oxalic acid possess moderate cytotoxicity (EC50 value 1.64 mM and 4.19 mM for fish and human cell line, respectively). Results on phytotoxicity imply that tested DESs are non-toxic with seed germination EC50 values higher than 5000 mg L(-1). All tested DESs were classified as'readily biodegradable' based on their high levels of mineralization (68-96%). These findings indicate that DESs have a green profile and a good prospect for a wider use in the field of green technologies. Copyright © 2014 Elsevier Inc. All rights reserved.

Monolithic microwave integrated circuit devices for active array antennas

NASA Technical Reports Server (NTRS)

Mittra, R.

1984-01-01

Two different aspects of active antenna array design were investigated. The transition between monolithic microwave integrated circuits and rectangular waveguides was studied along with crosstalk in multiconductor transmission lines. The boundary value problem associated with a discontinuity in a microstrip line is formulated. This entailed, as a first step, the derivation of the propagating as well as evanescent modes of a microstrip line. The solution is derived to a simple discontinuity problem: change in width of the center strip. As for the multiconductor transmission line problem. A computer algorithm was developed for computing the crosstalk noise from the signal to the sense lines. The computation is based on the assumption that these lines are terminated in passive loads.

Iron K Lines from Gamma Ray Bursts

NASA Technical Reports Server (NTRS)

Kallman, T. R.; Meszaros, P.; Rees, M. J.

2003-01-01

We present models for reprocessing of an intense flux of X-rays and gamma rays expected in the vicinity of gamma ray burst sources. We consider the transfer and reprocessing of the energetic photons into observable features in the X-ray band, notably the K lines of iron. Our models are based on the assumption that the gas is sufficiently dense to allow the microphysical processes to be in a steady state, thus allowing efficient line emission with modest reprocessing mass and elemental abundances ranging from solar to moderately enriched. We show that the reprocessing is enhanced by down-Comptonization of photons whose energy would otherwise be too high to absorb on iron, and that pair production can have an effect on enhancing the line production. Both "distant" reprocessors such as supernova or wind remnants and "nearby" reprocessors such as outer stellar envelopes can reproduce the observed line fluxes with Fe abundances 30-100 times above solar, depending on the incidence angle. The high incidence angles required arise naturally only in nearby models, which for plausible values can reach Fe line to continuum ratios close to the reported values.

Evaluating the Effect of Labeled Benchmarks on Children’s Number Line Estimation Performance and Strategy Use

PubMed Central

Peeters, Dominique; Sekeris, Elke; Verschaffel, Lieven; Luwel, Koen

2017-01-01

Some authors argue that age-related improvements in number line estimation (NLE) performance result from changes in strategy use. More specifically, children’s strategy use develops from only using the origin of the number line, to using the origin and the endpoint, to eventually also relying on the midpoint of the number line. Recently, Peeters et al. (unpublished) investigated whether the provision of additional unlabeled benchmarks at 25, 50, and 75% of the number line, positively affects third and fifth graders’ NLE performance and benchmark-based strategy use. It was found that only the older children benefitted from the presence of these benchmarks at the quartiles of the number line (i.e., 25 and 75%), as they made more use of these benchmarks, leading to more accurate estimates. A possible explanation for this lack of improvement in third graders might be their inability to correctly link the presented benchmarks with their corresponding numerical values. In the present study, we investigated whether labeling these benchmarks with their corresponding numerical values, would have a positive effect on younger children’s NLE performance and quartile-based strategy use as well. Third and sixth graders were assigned to one of three conditions: (a) a control condition with an empty number line bounded by 0 at the origin and 1,000 at the endpoint, (b) an unlabeled condition with three additional external benchmarks without numerical labels at 25, 50, and 75% of the number line, and (c) a labeled condition in which these benchmarks were labeled with 250, 500, and 750, respectively. Results indicated that labeling the benchmarks has a positive effect on third graders’ NLE performance and quartile-based strategy use, whereas sixth graders already benefited from the mere provision of unlabeled benchmarks. These findings imply that children’s benchmark-based strategy use can be stimulated by adding additional externally provided benchmarks on the number line, but that, depending on children’s age and familiarity with the number range, these additional external benchmarks might need to be labeled. PMID:28713302

Evaluating the Effect of Labeled Benchmarks on Children's Number Line Estimation Performance and Strategy Use.

PubMed

Peeters, Dominique; Sekeris, Elke; Verschaffel, Lieven; Luwel, Koen

2017-01-01

Some authors argue that age-related improvements in number line estimation (NLE) performance result from changes in strategy use. More specifically, children's strategy use develops from only using the origin of the number line, to using the origin and the endpoint, to eventually also relying on the midpoint of the number line. Recently, Peeters et al. (unpublished) investigated whether the provision of additional unlabeled benchmarks at 25, 50, and 75% of the number line, positively affects third and fifth graders' NLE performance and benchmark-based strategy use. It was found that only the older children benefitted from the presence of these benchmarks at the quartiles of the number line (i.e., 25 and 75%), as they made more use of these benchmarks, leading to more accurate estimates. A possible explanation for this lack of improvement in third graders might be their inability to correctly link the presented benchmarks with their corresponding numerical values. In the present study, we investigated whether labeling these benchmarks with their corresponding numerical values, would have a positive effect on younger children's NLE performance and quartile-based strategy use as well. Third and sixth graders were assigned to one of three conditions: (a) a control condition with an empty number line bounded by 0 at the origin and 1,000 at the endpoint, (b) an unlabeled condition with three additional external benchmarks without numerical labels at 25, 50, and 75% of the number line, and (c) a labeled condition in which these benchmarks were labeled with 250, 500, and 750, respectively. Results indicated that labeling the benchmarks has a positive effect on third graders' NLE performance and quartile-based strategy use, whereas sixth graders already benefited from the mere provision of unlabeled benchmarks. These findings imply that children's benchmark-based strategy use can be stimulated by adding additional externally provided benchmarks on the number line, but that, depending on children's age and familiarity with the number range, these additional external benchmarks might need to be labeled.

An Accurate Potential Energy Surface for H2O

NASA Technical Reports Server (NTRS)

Schwenke, David W.; Partridge, Harry; Langhoff, Stephen R. (Technical Monitor)

1997-01-01

We have carried out extensive high quality ab initio electronic structure calculations of the ground state potential energy surface (PES) and dipole moment function (DMF) for H2O. A small adjustment is made to the PES to improve the agreement of line positions from theory and experiment. The theoretical line positions are obtained from variational ro-vibrational calculations using the exact kinetic energy operator. For the lines being fitted, the root-mean-square error was reduced from 6.9 to 0.08 /cm. We were then able to match 30,092 of the 30,117 lines from the HITRAN 96 data base to theoretical lines, and 80% of the line positions differed less than 0.1 /cm. About 3% of the line positions in the experimental data base appear to be incorrect. Theory predicts the existence of many additional weak lines with intensities above the cutoff used in the data base. To obtain results of similar accuracy for HDO, a mass dependent correction to the PH is introduced and is parameterized by simultaneously fitting line positions for HDO and D2O. The mass dependent PH has good predictive value for T2O and HTO. Nonadiabatic effects are not explicitly included. Line strengths for vibrational bands summed over rotational levels usually agree well between theory and experiment, but individual line strengths can differ greatly. A high temperature line list containing about 380 million lines has been generated using the present PES and DMF

The Title and Three Core Values from the First Three Lines of The Declaration of Independence

ERIC Educational Resources Information Center

White, Kenneth Michael

2013-01-01

Teaching the Declaration of Independence can be a challenge. This article presents a lesson plan based on an explication of the title and the first three lines of the Declaration intended to make the American founding era relevant to today's college students. Assuming civic education is a major goal of teaching American Government, assuming…

An Novel Continuation Power Flow Method Based on Line Voltage Stability Index

NASA Astrophysics Data System (ADS)

Zhou, Jianfang; He, Yuqing; He, Hongbin; Jiang, Zhuohan

2018-01-01

An novel continuation power flow method based on line voltage stability index is proposed in this paper. Line voltage stability index is used to determine the selection of parameterized lines, and constantly updated with the change of load parameterized lines. The calculation stages of the continuation power flow decided by the angle changes of the prediction of development trend equation direction vector are proposed in this paper. And, an adaptive step length control strategy is used to calculate the next prediction direction and value according to different calculation stages. The proposed method is applied clear physical concept, and the high computing speed, also considering the local characteristics of voltage instability which can reflect the weak nodes and weak area in a power system. Due to more fully to calculate the PV curves, the proposed method has certain advantages on analysing the voltage stability margin to large-scale power grid.

Differential sensitivity of melanoma cell lines with BRAFV600E mutation to the specific Raf inhibitor PLX4032

PubMed Central

2010-01-01

Blocking oncogenic signaling induced by the BRAFV600E mutation is a promising approach for melanoma treatment. We tested the anti-tumor effects of a specific inhibitor of Raf protein kinases, PLX4032/RG7204, in melanoma cell lines. PLX4032 decreased signaling through the MAPK pathway only in cell lines with the BRAFV600E mutation. Seven out of 10 BRAFV600E mutant cell lines displayed sensitivity based on cell viability assays and three were resistant at concentrations up to 10 μM. Among the sensitive cell lines, four were highly sensitive with IC50 values below 1 μM, and three were moderately sensitive with IC50 values between 1 and 10 μM. There was evidence of MAPK pathway inhibition and cell cycle arrest in both sensitive and resistant cell lines. Genomic analysis by sequencing, genotyping of close to 400 oncogeninc mutations by mass spectrometry, and SNP arrays demonstrated no major differences in BRAF locus amplification or in other oncogenic events between sensitive and resistant cell lines. However, metabolic tracer uptake studies demonstrated that sensitive cell lines had a more profound inhibition of FDG uptake upon exposure to PLX4032 than resistant cell lines. In conclusion, BRAFV600E mutant melanoma cell lines displayed a range of sensitivities to PLX4032 and metabolic imaging using PET probes can be used to assess sensitivity. PMID:20406486

Singular dynamics of a q-difference Painlevé equation in its initial-value space

NASA Astrophysics Data System (ADS)

Joshi, N.; Lobb, S. B.

2016-01-01

We construct the initial-value space of a q-discrete first Painlevé equation explicitly and describe the behaviours of its solutions w(n) in this space as n\\to ∞ , with particular attention paid to neighbourhoods of exceptional lines and irreducible components of the anti-canonical divisor. These results show that trajectories starting in domains bounded away from the origin in initial value space are repelled away from such singular lines. However, the dynamical behaviours in neighbourhoods containing the origin are complicated by the merger of two simple base points at the origin in the limit. We show that these lead to a saddle-point-type behaviour in a punctured neighbourhood of the origin.

Redefining Health: Implication for Value-Based Healthcare Reform.

PubMed

Putera, Ikhwanuliman

2017-03-02

Health definition consists of three domains namely, physical, mental, and social health that should be prioritized in delivering healthcare. The emergence of chronic diseases in aging populations has been a barrier to the realization of a healthier society. The value-based healthcare concept seems in line with the true health objective: increasing value. Value is created from health outcomes which matter to patients relative to the cost of achieving those outcomes. The health outcomes should include all domains of health in a full cycle of care. To implement value-based healthcare, transformations need to be done by both health providers and patients: establishing true health outcomes, strengthening primary care, building integrated health systems, implementing appropriate health payment schemes that promote value and reduce moral hazards, enabling health information technology, and creating a policy that fits well with a community.

Comparison of a teratogenic transcriptome-based predictive test based on human embryonic versus inducible pluripotent stem cells.

PubMed

Shinde, Vaibhav; Perumal Srinivasan, Sureshkumar; Henry, Margit; Rotshteyn, Tamara; Hescheler, Jürgen; Rahnenführer, Jörg; Grinberg, Marianna; Meisig, Johannes; Blüthgen, Nils; Waldmann, Tanja; Leist, Marcel; Hengstler, Jan Georg; Sachinidis, Agapios

2016-12-30

Human embryonic stem cells (hESCs) partially recapitulate early embryonic three germ layer development, allowing testing of potential teratogenic hazards. Because use of hESCs is ethically debated, we investigated the potential for human induced pluripotent stem cells (hiPSCs) to replace hESCs in such tests. Three cell lines, comprising hiPSCs (foreskin and IMR90) and hESCs (H9) were differentiated for 14 days. Their transcriptome profiles were obtained on day 0 and day 14 and analyzed by comprehensive bioinformatics tools. The transcriptomes on day 14 showed that more than 70% of the "developmental genes" (regulated genes with > 2-fold change on day 14 compared to day 0) exhibited variability among cell lines. The developmental genes belonging to all three cell lines captured biological processes and KEGG pathways related to all three germ layer embryonic development. In addition, transcriptome profiles were obtained after 14 days of exposure to teratogenic valproic acid (VPA) during differentiation. Although the differentially regulated genes between treated and untreated samples showed more than 90% variability among cell lines, VPA clearly antagonized the expression of developmental genes in all cell lines: suppressing upregulated developmental genes, while inducing downregulated ones. To quantify VPA-disturbed development based on developmental genes, we estimated the "developmental potency" (D p ) and "developmental index" (D i ). Despite differences in genes deregulated by VPA, uniform D i values were obtained for all three cell lines. Given that the D i values for VPA were similar for hESCs and hiPSCs, D i can be used for robust hazard identification, irrespective of whether hESCs or hiPSCs are used in the test systems.

[The research on separating and extracting overlapping spectral feature lines in LIBS using damped least squares method].

PubMed

Wang, Yin; Zhao, Nan-jing; Liu, Wen-qing; Yu, Yang; Fang, Li; Meng, De-shuo; Hu, Li; Zhang, Da-hai; Ma, Min-jun; Xiao, Xue; Wang, Yu; Liu, Jian-guo

2015-02-01

In recent years, the technology of laser induced breakdown spectroscopy has been developed rapidly. As one kind of new material composition detection technology, laser induced breakdown spectroscopy can simultaneously detect multi elements fast and simply without any complex sample preparation and realize field, in-situ material composition detection of the sample to be tested. This kind of technology is very promising in many fields. It is very important to separate, fit and extract spectral feature lines in laser induced breakdown spectroscopy, which is the cornerstone of spectral feature recognition and subsequent elements concentrations inversion research. In order to realize effective separation, fitting and extraction of spectral feature lines in laser induced breakdown spectroscopy, the original parameters for spectral lines fitting before iteration were analyzed and determined. The spectral feature line of' chromium (Cr I : 427.480 nm) in fly ash gathered from a coal-fired power station, which was overlapped with another line(FeI: 427.176 nm), was separated from the other one and extracted by using damped least squares method. Based on Gauss-Newton iteration, damped least squares method adds damping factor to step and adjust step length dynamically according to the feedback information after each iteration, in order to prevent the iteration from diverging and make sure that the iteration could converge fast. Damped least squares method helps to obtain better results of separating, fitting and extracting spectral feature lines and give more accurate intensity values of these spectral feature lines: The spectral feature lines of chromium in samples which contain different concentrations of chromium were separated and extracted. And then, the intensity values of corresponding spectral lines were given by using damped least squares method and least squares method separately. The calibration curves were plotted, which showed the relationship between spectral line intensity values and chromium concentrations in different samples. And then their respective linear correlations were compared. The experimental results showed that the linear correlation of the intensity values of spectral feature lines and the concentrations of chromium in different samples, which was obtained by damped least squares method, was better than that one obtained by least squares method. And therefore, damped least squares method was stable, reliable and suitable for separating, fitting and extracting spectral feature lines in laser induced breakdown spectroscopy.

Do McKinnon lists provide reliable data in bird species frequency? A comparison with transect-based data

NASA Astrophysics Data System (ADS)

Cento, Michele; Scrocca, Roberto; Coppola, Michele; Rossi, Maurizio; Di Giuseppe, Riccardo; Battisti, Corrado; Luiselli, Luca; Amori, Giovanni

2018-05-01

Although occurrence-based listing methods could provide reliable lists of species composition for a site, the effective reliability of this method to provide more detailed information about species frequency (and abundance) has been rarely tested. In this paper, we compared the species frequencies obtained for the same set of species-rich sites (wetlands of central Italy) from two different methods: McKinnon lists and line transects. In all sites we observed: (i) rapid cumulating curves of line transect abundance frequencies toward the asymptote represented by the maximum value in McKinnon occurrence frequency; (ii) a large amount of species having a low frequency with line transect method showing a high range of variation in frequency obtained by McKinnon lists; (iii) a set of species having a subdominant (>0.02-<0.05) and dominant species (>0.05) frequency with line transect showed all the highest value in McKinnon frequency. McKinnon lists provides only a coarse-grained proxy of species frequency of individuals distinguishing only between common species (having the highest values of McKinnon frequency) and rare species (all the other species). Although McKinnon lists have some points of strength, this method does not discriminate the frequencies inside the subset of common species (sub-dominant and dominant species). Therefore, we suggest a cautionary approach when McKinnon frequencies should be used to obtain complex univariate metrics of diversity.

A Quasi-Steady Lifting Line Theory for Insect-Like Hovering Flight

PubMed Central

Nabawy, Mostafa R. A.; Crowthe, William J.

2015-01-01

A novel lifting line formulation is presented for the quasi-steady aerodynamic evaluation of insect-like wings in hovering flight. The approach allows accurate estimation of aerodynamic forces from geometry and kinematic information alone and provides for the first time quantitative information on the relative contribution of induced and profile drag associated with lift production for insect-like wings in hover. The main adaptation to the existing lifting line theory is the use of an equivalent angle of attack, which enables capture of the steady non-linear aerodynamics at high angles of attack. A simple methodology to include non-ideal induced effects due to wake periodicity and effective actuator disc area within the lifting line theory is included in the model. Low Reynolds number effects as well as the edge velocity correction required to account for different wing planform shapes are incorporated through appropriate modification of the wing section lift curve slope. The model has been successfully validated against measurements from revolving wing experiments and high order computational fluid dynamics simulations. Model predicted mean lift to weight ratio results have an average error of 4% compared to values from computational fluid dynamics for eight different insect cases. Application of an unmodified linear lifting line approach leads on average to a 60% overestimation in the mean lift force required for weight support, with most of the discrepancy due to use of linear aerodynamics. It is shown that on average for the eight insects considered, the induced drag contributes 22% of the total drag based on the mean cycle values and 29% of the total drag based on the mid half-stroke values. PMID:26252657

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawler, J. E.; Sneden, C.; Cowan, J. J., E-mail: jelawler@wisc.edu, E-mail: chris@verdi.as.utexas.edu, E-mail: jjcowan1@ou.edu

New emission branching fraction measurements for 898 lines of the first spectrum of cobalt (Co i) are determined from hollow cathode lamp spectra recorded with the National Solar Observatory 1 m Fourier transform spectrometer on Kitt Peak, AZ and a high-resolution echelle spectrometer. Published radiative lifetimes from laser induced fluorescence measurements are combined with the branching fractions to determine accurate absolute atomic transition probabilities for the 898 lines. Hyperfine structure (hfs) constants for levels of neutral Co in the literature are surveyed and selected values are used to generate complete hfs component patterns for 195 transitions of Co i. Thesemore » new laboratory data are applied to determine the Co abundance in the Sun and metal-poor star HD 84937, yielding log ϵ(Co) = 4.955 ± 0.007 (σ = 0.059) based on 82 Co i lines and log ϵ(Co) = 2.785 ± 0.008 (σ = 0.065) based on 66 Co i lines, respectively. A Saha or ionization balance test on the photosphere of HD 84937 is performed using 16 UV lines of Co ii, and good agreement is found with the Co i result in this metal-poor ([Fe i/H] = −2.32, [Fe ii/H] = −2.32) dwarf star. The resulting value of [Co/Fe] = +0.14 supports a rise of Co/Fe at low metallicity that has been suggested in other studies.« less

An Online Compendium of CHO RNA-Seq Data Allows Identification of CHO Cell Line-specific Transcriptomic Signatures.

PubMed

Singh, Ankita; Kildegaard, Helene F; Andersen, Mikael R

2018-05-15

Chinese hamster ovary (CHO) cell lines can fold, assemble and modify proteins post-translationally to produce human-like proteins; as a consequence, it is the single most common expression systems for industrial production of recombinant therapeutic proteins. A thorough knowledge of cultivation conditions of different CHO cell lines has been developed over the last decade, but comprehending gene or pathway-specific distinctions between CHO cell lines at transcriptome level remains a challenge. To address these challenges, we compiled a compendium of 23 RNA-Seq studies from public and in-house data on CHO cell lines, i.e. CHO-S, CHO-K1 and DG44. Significantly differentially expressed (DE) genes particularly related to subcellular structure and macromolecular categories were used to identify differences between the cell lines. A R-based web application was developed specifically for CHO cell lines to further visualize expression values across different cell lines, and make available the normalized full CHO data set graphically as a CHO research community resource. This study quantitatively categorizes CHO cell lines based on patterns at transcriptomic level and detects gene and pathway specific key distinctions among sibling cell lines. Studies such as this can be used to select desired characteristics across various CHO cell lines. Furthermore, the availability of the data as an internet-based application can be applied to broad range of CHO engineering applications. This article is protected by copyright. All rights reserved.

Research on the critical parameters initialization of optical PMD compensator in high bit-rate systems

NASA Astrophysics Data System (ADS)

Zhao, Wenyu; Zhang, Haiyi; Ji, Yuefeng; Xu, Daxiong

2004-05-01

Based on the proposed polarization mode dispersion (PMD) compensation simulation model and statistical analysis method (Monte-Carlo), the critical parameters initialization of two typical optical domain PMD compensators, which include optical PMD method with fixed compensation differential group delay (DGD) and that with variable compensation DGD, are detailedly investigated by numerical method. In the simulation, the line PMD values are chosen as 3ps, 4ps and 5ps and run samples are set to 1000 in order to achieve statistical evaluation for PMD compensated systems, respectively. The simulation results show that for the PMD value pre-known systems, the value of the fixed DGD compensator should be set to 1.5~1.6 times of line PMD value in order to reach the optimum performance, but for the second kind of PMD compensator, the DGD range of lower limit should be 1.5~1.6 times of line PMD provided that of upper limit is set to 3 times of line PMD, if no effective ways are chosen to resolve the problem of local minimum in optimum process. Another conclusion can be drawn from the simulation is that, although the second PMD compensator holds higher PMD compensation performance, it will spend more feedback loops to look up the optimum DGD value in the real PMD compensation realization, and this will bring more requirements on adjustable DGD device, not only wider adjustable range, but rapid adjusting speed for real time PMD equalization.

The Motivational Value Systems Questionnaire (MVSQ): Psychometric Analysis Using a Forced Choice Thurstonian IRT Model

PubMed Central

Merk, Josef; Schlotz, Wolff; Falter, Thomas

2017-01-01

This study presents a new measure of value systems, the Motivational Value Systems Questionnaire (MVSQ), which is based on a theory of value systems by psychologist Clare W. Graves. The purpose of the instrument is to help people identify their personal hierarchies of value systems and thus become more aware of what motivates and demotivates them in work-related contexts. The MVSQ is a forced-choice (FC) measure, making it quicker to complete and more difficult to intentionally distort, but also more difficult to assess its psychometric properties due to ipsativity of FC data compared to rating scales. To overcome limitations of ipsative data, a Thurstonian IRT (TIRT) model was fitted to the questionnaire data, based on a broad sample of N = 1,217 professionals and students. Comparison of normative (IRT) scale scores and ipsative scores suggested that MVSQ IRT scores are largely freed from restrictions due to ipsativity and thus allow interindividual comparison of scale scores. Empirical reliability was estimated using a sample-based simulation approach which showed acceptable and good estimates and, on average, slightly higher test-retest reliabilities. Further, validation studies provided evidence on both construct validity and criterion-related validity. Scale score correlations and associations of scores with both age and gender were largely in line with theoretically- and empirically-based expectations, and results of a multitrait-multimethod analysis supports convergent and discriminant construct validity. Criterion validity was assessed by examining the relation of value system preferences to departmental affiliation which revealed significant relations in line with prior hypothesizing. These findings demonstrate the good psychometric properties of the MVSQ and support its application in the assessment of value systems in work-related contexts. PMID:28979228

The Motivational Value Systems Questionnaire (MVSQ): Psychometric Analysis Using a Forced Choice Thurstonian IRT Model.

PubMed

Merk, Josef; Schlotz, Wolff; Falter, Thomas

2017-01-01

This study presents a new measure of value systems, the Motivational Value Systems Questionnaire (MVSQ), which is based on a theory of value systems by psychologist Clare W. Graves. The purpose of the instrument is to help people identify their personal hierarchies of value systems and thus become more aware of what motivates and demotivates them in work-related contexts. The MVSQ is a forced-choice (FC) measure, making it quicker to complete and more difficult to intentionally distort, but also more difficult to assess its psychometric properties due to ipsativity of FC data compared to rating scales. To overcome limitations of ipsative data, a Thurstonian IRT (TIRT) model was fitted to the questionnaire data, based on a broad sample of N = 1,217 professionals and students. Comparison of normative (IRT) scale scores and ipsative scores suggested that MVSQ IRT scores are largely freed from restrictions due to ipsativity and thus allow interindividual comparison of scale scores. Empirical reliability was estimated using a sample-based simulation approach which showed acceptable and good estimates and, on average, slightly higher test-retest reliabilities. Further, validation studies provided evidence on both construct validity and criterion-related validity. Scale score correlations and associations of scores with both age and gender were largely in line with theoretically- and empirically-based expectations, and results of a multitrait-multimethod analysis supports convergent and discriminant construct validity. Criterion validity was assessed by examining the relation of value system preferences to departmental affiliation which revealed significant relations in line with prior hypothesizing. These findings demonstrate the good psychometric properties of the MVSQ and support its application in the assessment of value systems in work-related contexts.

Electromigration in epitaxial Cu(001) lines

NASA Astrophysics Data System (ADS)

Ramanath, G.; Kim, H.; Goindi, H. S.; Frederick, M. J.; Shin, C.-S.; Goswami, R.; Petrov, I.; Greene, J. E.

2002-04-01

We report the electromigration (EM) response of single-domain epitaxial Cu(001) lines on layers of Ta, TaN, and TiN. Epitaxial Cu(001) lines on nitride layers exhibit nearly two orders of magnitude higher mean-time-to-failure (MTTF) values than those on Ta, indicating the strong influence of the underlayer. The activation energy of EM for Cu on the nitrides is ˜0.8-1.2 eV, and that of Cu on Ta is ˜0.2 eV, for 200-300 °C. Our results also indicate that the MTTF values correlate inversely to the crystal quality of the Cu layers measured by X-ray diffraction. The EM resistance of epitaxial Cu lines with different crystal quality on TaN were measured to separate the effects of interface chemistry and crystal quality. While higher quality epitaxial films reveal a higher EM resistance, the magnitude of the change is smaller than that obtained by changing the interface chemistry. Epitaxial lines exhibit more than 3-4 orders of magnitude higher MTTF than polycrystalline lines on the same underlayer. Based upon our results, we propose that the Cu/underlayer interface chemistry and presence of grain boundary diffusion play important roles in unpassivated Cu films.

The mass of the black hole in the X-ray binary LMC X-1

NASA Astrophysics Data System (ADS)

Abubekerov, M. K.; Antokhina, E. A.; Gostev, N. Yu.; Cherepashchuk, A. M.; Shimansky, V. V.

2016-12-01

A dynamical estimate of the mass of the black hole in the LMC X-1 binary system is obtained in the framework of a Roche model for the optical star, based on fitting of the He I 4471 Å and He II 4200 Å absorption lines assuming LTE. The mass of the black hole derived from the radial-velocity curve for the He II 4200 Å line is m x = 10.55 M ⊙, close to the value found earlier based on a model with two point bodies [1].

The self- and foreign-absorption continua of water vapor by cavity ring-down spectroscopy near 2.35 μm.

PubMed

Mondelain, D; Vasilchenko, S; Čermák, P; Kassi, S; Campargue, A

2015-07-21

The room temperature self- and foreign-continua of water vapor have been measured near 4250 cm(-1) with a newly developed high sensitivity cavity ring down spectrometer (CRDS). The typical sensitivity of the recordings is αmin≈ 6 × 10(-10) cm(-1) which is two orders of magnitude better than previous Fourier transform spectroscopy (FTS) measurements in the spectral region. The investigated spectral interval is located in the low energy range of the important 2.1 μm atmospheric transparency window. Self-continuum cross-sections, CS, were retrieved from the quadratic dependence of the spectrum base line level measured for different water vapor pressures between 0 and 15 Torr, after subtraction of the local water monomer lines contribution calculated using HITRAN2012 line parameters. The CS values were determined with 5% accuracy for four spectral points between 4249.2 and 4257.3 cm(-1). Their values of about 3.2 × 10(-23) cm(2) molecule(-1) atm(-1) are found 20% higher than predicted by the MT_CKD V2.5 model but two times weaker than reported in the literature using FTS. The foreign-continuum was evaluated by injecting various amounts of synthetic air in the CRDS cell while keeping the initial water vapor partial pressure constant. The foreign-continuum cross-section, CF, was retrieved from a linear fit of the spectrum base line level versus the air pressure. The obtained CF values are larger by a factor of 4.5 compared to the MT_CKD values and smaller by a factor of 1.7 compared to previous FTS values. As a result, for an atmosphere at room temperature with 60% relative humidity, the foreign-continuum contribution to the water continuum near 4250 cm(-1) is found to be on the same order as the self-continuum contribution.

Computer guided restoration of joint line and femoral offset in cruciate substituting total knee arthroplasty.

PubMed

Shetty, Gautam M; Mullaji, Arun; Bhayde, Sagar

2012-10-01

This prospective study aimed to evaluate radiographically, change in joint line and femoral condylar offset with the optimized gap balancing technique in computer-assisted, primary, cruciate-substituting total knee arthroplasties (TKAs). One hundred and twenty-nine consecutive computer-assisted TKAs were evaluated radiographically using pre- and postoperative full-length standing hip-to-ankle, antero-posterior and lateral radiographs to assess change in knee deformity, joint line height and posterior condylar offset. In 49% of knees, there was a net decrease (mean 2.2mm, range 0.2-8.4mm) in joint line height postoperatively whereas 46.5% of knees had a net increase in joint line height (mean 2.5mm, range 0.2-11.2mm). In 93% of the knees, joint line was restored to within ± 5 mm of preoperative values. In 53% of knees, there was a net increase (mean 2.9 mm, range 0.2-12 mm) in posterior offset postoperatively whereas 40% of knees had a net decrease in posterior offset (mean 4.2mm, range 0.6-20mm). In 82% of knees, the posterior offset was restored within ± 5 mm of preoperative values. Based on radiographic evaluation in extension and at 30° flexion, the current study clearly demonstrates that joint line and posterior femoral condylar offset can be restored in the majority of computer-assisted, cruciate-substituting TKAs to within 5mm of their preoperative value. The optimized gap balancing feature of the computer software allows the surgeon to simulate the effect of simultaneously adjusting femoral component size, position and distal femoral resection level on joint line and posterior femoral offset. Copyright © 2011 Elsevier B.V. All rights reserved.

Design of a Sixteen Bit Pipelined Adder Using CMOS Bulk P-Well Technology.

DTIC Science & Technology

1984-12-01

node’s current value. These rules are based on the assumption that the event that was last calculated reflects the latest configuraticn of the network...Lines beginning with - are treated as ll comment. The parameter names and their default values are: ;configuration file for ’standard’ MPC procem capm .2a

Off-line data reduction

NASA Astrophysics Data System (ADS)

Gutowski, Marek W.

1992-12-01

Presented is a novel, heuristic algorithm, based on fuzzy set theory, allowing for significant off-line data reduction. Given the equidistant data, the algorithm discards some points while retaining others with their original values. The fraction of original data points retained is typically {1}/{6} of the initial value. The reduced data set preserves all the essential features of the input curve. It is possible to reconstruct the original information to high degree of precision by means of natural cubic splines, rational cubic splines or even linear interpolation. Main fields of application should be non-linear data fitting (substantial savings in CPU time) and graphics (storage space savings).

Numerical Simulations for Distribution Characteristics of Internal Forces on Segments of Tunnel Linings

NASA Astrophysics Data System (ADS)

Li, Shouju; Shangguan, Zichang; Cao, Lijuan

A procedure based on FEM is proposed to simulate interaction between concrete segments of tunnel linings and soils. The beam element named as Beam 3 in ANSYS software was used to simulate segments. The ground loss induced from shield tunneling and segment installing processes is simulated in finite element analysis. The distributions of bending moment, axial force and shear force on segments were computed by FEM. The commutated internal forces on segments will be used to design reinforced bars on shield linings. Numerically simulated ground settlements agree with observed values.

A study of the H2O absorption line shifts in the visible spectrum region due to air pressure

NASA Technical Reports Server (NTRS)

Grossmann, B. E.; Browell, E. V.; Bykov, A. D.; Kapitanov, V. A.; Korotchenko, E. A.

1990-01-01

Results of measured and calculated shift coefficients are presented for 170 absorption lines of H2O in five vibrational-rotational bands. The measurements have been carried out using highly sensitive laser spectrometers with a resolution of at least 0.01/cm; the calculations are based on the Anderson-Tsao-Curnutte-Frost method. Good agreement is obtained between the theoretical and experimental values of the shift coefficients of H2O lines due to N2, O2, and air pressure.

Analysis of micro-failure behaviors in artificial muscles based on fishing line and sewing thread

NASA Astrophysics Data System (ADS)

Xu, J. B.; Cheng, K. F.; Tu, S. L.; He, X. M.; Ma, C.; Jin, Y. Z.; Kang, X. N.; Sun, T.; Zhang, Y.

2017-06-01

The aim of the present study was to discuss a new and effective method for testing artificial muscles based on micro-failure behaviors analysis. Thermo-mechanical actuators based on fishing line and sewing thread, also, the capability of responding to ambient temperature variations producing a large amount of shrinkage ratio of a resulting variation in longitudinal length. The minimum micro-failure value is 0.02μm and the maximum value is 1.72μm with nylon twist pattern. The discovery of an innovative effective testing of artificial muscles based on polymeric fibers specimens on micro-failure, rupture, slippage, etc. This research finds out a micro-failure behavior analysis of thermo-mechanical actuators based on fishing line and sewing thread. The specimens show large deformations when heated together with warping performance in terms of shrinkage of energy and densities. With the purpose of providing useful analysis data for the further technology applications, we attempt micrometre-sized artificial muscles which were also tested was readily accessible and also can be applied to other polymeric fibers. Effective use of this technique achievement relies on rotate speed, temperature and tensile direction. The results of the tensile testing experiments were outstanding with respect to some important issues related to the response of micro-structure, twisted polymeric fibers and shrinkage ratio.

Skyshine line-beam response functions for 20- to 100-MeV photons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brockhoff, R.C.; Shultis, J.K.; Faw, R.E.

1996-06-01

The line-beam response function, needed for skyshine analyses based on the integral line-beam method, was evaluated with the MCNP Monte Carlo code for photon energies from 20 to 100 MeV and for source-to-detector distances out to 1,000 m. These results are compared with point-kernel results, and the effects of bremsstrahlung and positron transport in the air are found to be important in this energy range. The three-parameter empirical formula used in the integral line-beam skyshine method was fit to the MCNP results, and values of these parameters are reported for various source energies and angles.

Incidence and trends of central line associated pneumothorax using radiograph report text search versus administrative database codes.

PubMed

Reeson, Marc; Forster, Alan; van Walraven, Carl

2018-05-25

Central line associated pneumothorax (CLAP) could be a good quality of care indicator because they are objectively measured, clearly undesirable and possibly avoidable. We measured the incidence and trends of CLAP using radiograph report text search with manual review and compared them with measures using routinely collected health administrative data. For each hospitalisation to a tertiary care teaching hospital between 2002 and 2015, we searched all chest radiography reports for a central line with a sensitive computer algorithm. Screen positive reports were manually reviewed to confirm central lines. The index and subsequent chest radiography reports were screened for pneumothorax followed by manual confirmation. Diagnostic and procedural codes were used to identify CLAP in administrative data. In 685 044 hospitalisations, 10 819 underwent central line insertion (1.6%) with CLAP occurring 181 times (1.7%). CLAP risk did not change over time. Codes for CLAP were inaccurate (sensitivity 13.8%, positive predictive value 6.6%). However, overall code-based CLAP risk (1.8%) was almost identical to actual values possibly because patient strata with inflated CLAP risk were balanced by more common strata having underestimated CLAP risk. Code-based methods inflated central line incidence 2.2 times and erroneously concluded that CLAP risk decreased significantly over time. Using valid methods, CLAP incidence was similar to those in the literature but has not changed over time. Although administrative database codes for CLAP were very inaccurate, they generated CLAP risks very similar to actual values because of offsetting errors. In contrast to those from radiograph report text search with manual review, CLAP trends decreased significantly using administrative data. Hospital CLAP risk should not be measured using administrative data. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Marketing the `Broad Line': Invitations to STEM education in a Swedish recruitment campaign

NASA Astrophysics Data System (ADS)

Andrée, Maria; Hansson, Lena

2013-01-01

In many Western societies, there is a concern about the tendency of young people not choosing Science, Technology, Engineering, and Mathematics (STEM) education and occupations. In response, different initiatives have been launched. If one believes that science should have a place in more young people's lives, an important question is to what extent recruitment campaigns communicate messages that open up for STEM education to become relevant in young people's identity formation. Here, we analyse a Swedish government-initiated, primarily Internet-based recruitment attempt ('The Broad Line Campaign') aimed at increasing the number of young people choosing the natural science programme in upper secondary school. The campaign is based on marketing principles and deliberately draws on identity issues. The data analysed consists of campaign films and written resources describing the campaign. Data are analysed by use of the constant comparative approach in order to produce categories describing different messages about why to engage in STEM education. These messages are then analysed from an identity perspective using the concept of subjective values. Our results show that the messages communicated in the Broad Line campaign emphasise utility value, attainment value and relative cost rather than interest-enjoyment. The campaign communicates that the natural science programme is to be associated with a high attainment value without establishing relations to the field of science. Finally, potential consequences of the communicated messages in the campaign are discussed in light of previous research.

Elemental abundance analyses with coadded Dominion Astrophysical Observatory spectrograms. II - The mercury-manganese stars 53 Tauri, Mu Leporis and Kappa Cancri

NASA Technical Reports Server (NTRS)

Adelman, Saul J.

1987-01-01

Elemental abundance analyses based on the coaddition of at least 10 2.4 A/mm Ila-O Dominion Astrophysical Observatory spectrograms have been performed for three mercury-manganese stars, 53 Tauri, Mu Leporis, and Kappa Cancri. These fine analyses show a greater degree of internal consistency than previous studies based on lower signal-to-noise data. Lines as weak as of order 3 mA are employed in these studies, and lines of atomic species not previously identified have been discovered. The status of 53 Tau as an anomalous member of this class is confirmed in that it lacks a Hg II 3984 A line even at the 2 mA level. Further, its surface gravity indicates it is less evolved than Mu Lep and Chi Cnc. Violations of the odd-even effect in the photospheric abundances of all three stars suggest that nonnuclear processes have operated in their atmospheres. Some of the values are substantially changed from their presumably initial solar values.

Calcium phosphate composite cements based on simple mixture of brushite and apatite phases

NASA Astrophysics Data System (ADS)

Egorov, A. A.; Fedotov, A. Yu; Pereloma, I. S.; Teterina, A. Yu; Sergeeva, N. S.; Sviridova, I. K.; Kirsanova, V. A.; Akhmedova, S. A.; Nesterova, A. V.; Reshetov, I. V.; Barinov, S. M.; Komlev, V. S.

2018-04-01

The composite cements based on simple mixtures brishite and apatite with ratio 70/30, 50/50, 30/70 were developed. The processes of phase formation, microstructure and mechanical properties were studied. The kinetics of degradation in simulated body fluid depending on the microstructure and the materials phase composition was carried out. The biological test in vitro were performed using the MTT-test on the human fibroblast immortalized (hFB) cell line and the human osteosarcoma cell line MG-63. The materials didn’t have acute cytoxicity and possessed surface matrix properties. It was determined that the both line of cells actively proliferated, with viable cells values higher 20-60 % then control at all observation periods.

Space Telescope and Optical Reverberation Mapping Project. V. Optical Spectroscopic Campaign and Emission-line Analysis for NGC 5548

DOE PAGES

Pei, L.; Fausnaugh, M. M.; Barth, A. J.; ...

2017-03-10

Here, we present the results of an optical spectroscopic monitoring program targeting NGC 5548 as part of a larger multiwavelength reverberation mapping campaign. The campaign spanned 6 months and achieved an almost daily cadence with observations from five ground-based telescopes. The Hβ and He II λ4686 broad emission-line light curves lag that of the 5100 Å optical continuum bymore » $${4.17}_{-0.36}^{+0.36}\\,\\mathrm{days}$$ and $${0.79}_{-0.34}^{+0.35}\\,\\mathrm{days}$$, respectively. The Hβ lag relative to the 1158 Å ultraviolet continuum light curve measured by the Hubble Space Telescope is ~50% longer than that measured against the optical continuum, and the lag difference is consistent with the observed lag between the optical and ultraviolet continua. This suggests that the characteristic radius of the broad-line region is ~50% larger than the value inferred from optical data alone. We also measured velocity-resolved emission-line lags for Hβ and found a complex velocity-lag structure with shorter lags in the line wings, indicative of a broad-line region dominated by Keplerian motion. The responses of both the Hβ and He ii emission lines to the driving continuum changed significantly halfway through the campaign, a phenomenon also observed for C iv, Lyα, He II(+O III]), and Si Iv(+O Iv]) during the same monitoring period. Finally, given the optical luminosity of NGC 5548 during our campaign, the measured Hβ lag is a factor of five shorter than the expected value implied by the R BLR–L AGN relation based on the past behavior of NGC 5548.« less

Space Telescope and Optical Reverberation Mapping Project. V. Optical Spectroscopic Campaign and Emission-line Analysis for NGC 5548

NASA Astrophysics Data System (ADS)

Pei, L.; Fausnaugh, M. M.; Barth, A. J.; Peterson, B. M.; Bentz, M. C.; De Rosa, G.; Denney, K. D.; Goad, M. R.; Kochanek, C. S.; Korista, K. T.; Kriss, G. A.; Pogge, R. W.; Bennert, V. N.; Brotherton, M.; Clubb, K. I.; Dalla Bontà, E.; Filippenko, A. V.; Greene, J. E.; Grier, C. J.; Vestergaard, M.; Zheng, W.; Adams, Scott M.; Beatty, Thomas G.; Bigley, A.; Brown, Jacob E.; Brown, Jonathan S.; Canalizo, G.; Comerford, J. M.; Coker, Carl T.; Corsini, E. M.; Croft, S.; Croxall, K. V.; Deason, A. J.; Eracleous, Michael; Fox, O. D.; Gates, E. L.; Henderson, C. B.; Holmbeck, E.; Holoien, T. W.-S.; Jensen, J. J.; Johnson, C. A.; Kelly, P. L.; Kim, S.; King, A.; Lau, M. W.; Li, Miao; Lochhaas, Cassandra; Ma, Zhiyuan; Manne-Nicholas, E. R.; Mauerhan, J. C.; Malkan, M. A.; McGurk, R.; Morelli, L.; Mosquera, Ana; Mudd, Dale; Muller Sanchez, F.; Nguyen, M. L.; Ochner, P.; Ou-Yang, B.; Pancoast, A.; Penny, Matthew T.; Pizzella, A.; Poleski, Radosław; Runnoe, Jessie; Scott, B.; Schimoia, Jaderson S.; Shappee, B. J.; Shivvers, I.; Simonian, Gregory V.; Siviero, A.; Somers, Garrett; Stevens, Daniel J.; Strauss, M. A.; Tayar, Jamie; Tejos, N.; Treu, T.; Van Saders, J.; Vican, L.; Villanueva, S., Jr.; Yuk, H.; Zakamska, N. L.; Zhu, W.; Anderson, M. D.; Arévalo, P.; Bazhaw, C.; Bisogni, S.; Borman, G. A.; Bottorff, M. C.; Brandt, W. N.; Breeveld, A. A.; Cackett, E. M.; Carini, M. T.; Crenshaw, D. M.; De Lorenzo-Cáceres, A.; Dietrich, M.; Edelson, R.; Efimova, N. V.; Ely, J.; Evans, P. A.; Ferland, G. J.; Flatland, K.; Gehrels, N.; Geier, S.; Gelbord, J. M.; Grupe, D.; Gupta, A.; Hall, P. B.; Hicks, S.; Horenstein, D.; Horne, Keith; Hutchison, T.; Im, M.; Joner, M. D.; Jones, J.; Kaastra, J.; Kaspi, S.; Kelly, B. C.; Kennea, J. A.; Kim, M.; Kim, S. C.; Klimanov, S. A.; Lee, J. C.; Leonard, D. C.; Lira, P.; MacInnis, F.; Mathur, S.; McHardy, I. M.; Montouri, C.; Musso, R.; Nazarov, S. V.; Netzer, H.; Norris, R. P.; Nousek, J. A.; Okhmat, D. N.; Papadakis, I.; Parks, J. R.; Pott, J.-U.; Rafter, S. E.; Rix, H.-W.; Saylor, D. A.; Schnülle, K.; Sergeev, S. G.; Siegel, M.; Skielboe, A.; Spencer, M.; Starkey, D.; Sung, H.-I.; Teems, K. G.; Turner, C. S.; Uttley, P.; Villforth, C.; Weiss, Y.; Woo, J.-H.; Yan, H.; Young, S.; Zu, Y.

2017-03-01

We present the results of an optical spectroscopic monitoring program targeting NGC 5548 as part of a larger multiwavelength reverberation mapping campaign. The campaign spanned 6 months and achieved an almost daily cadence with observations from five ground-based telescopes. The Hβ and He II λ4686 broad emission-line light curves lag that of the 5100 Å optical continuum by {4.17}-0.36+0.36 {days} and {0.79}-0.34+0.35 {days}, respectively. The Hβ lag relative to the 1158 Å ultraviolet continuum light curve measured by the Hubble Space Telescope is ˜50% longer than that measured against the optical continuum, and the lag difference is consistent with the observed lag between the optical and ultraviolet continua. This suggests that the characteristic radius of the broad-line region is ˜50% larger than the value inferred from optical data alone. We also measured velocity-resolved emission-line lags for Hβ and found a complex velocity-lag structure with shorter lags in the line wings, indicative of a broad-line region dominated by Keplerian motion. The responses of both the Hβ and He II emission lines to the driving continuum changed significantly halfway through the campaign, a phenomenon also observed for C IV, Lyα, He II(+O III]), and Si IV(+O IV]) during the same monitoring period. Finally, given the optical luminosity of NGC 5548 during our campaign, the measured Hβ lag is a factor of five shorter than the expected value implied by the R BLR-L AGN relation based on the past behavior of NGC 5548.

Space Telescope and Optical Reverberation Mapping Project. V. Optical Spectroscopic Campaign and Emission-line Analysis for NGC 5548

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pei, L.; Fausnaugh, M. M.; Barth, A. J.

Here, we present the results of an optical spectroscopic monitoring program targeting NGC 5548 as part of a larger multiwavelength reverberation mapping campaign. The campaign spanned 6 months and achieved an almost daily cadence with observations from five ground-based telescopes. The Hβ and He II λ4686 broad emission-line light curves lag that of the 5100 Å optical continuum bymore » $${4.17}_{-0.36}^{+0.36}\\,\\mathrm{days}$$ and $${0.79}_{-0.34}^{+0.35}\\,\\mathrm{days}$$, respectively. The Hβ lag relative to the 1158 Å ultraviolet continuum light curve measured by the Hubble Space Telescope is ~50% longer than that measured against the optical continuum, and the lag difference is consistent with the observed lag between the optical and ultraviolet continua. This suggests that the characteristic radius of the broad-line region is ~50% larger than the value inferred from optical data alone. We also measured velocity-resolved emission-line lags for Hβ and found a complex velocity-lag structure with shorter lags in the line wings, indicative of a broad-line region dominated by Keplerian motion. The responses of both the Hβ and He ii emission lines to the driving continuum changed significantly halfway through the campaign, a phenomenon also observed for C iv, Lyα, He II(+O III]), and Si Iv(+O Iv]) during the same monitoring period. Finally, given the optical luminosity of NGC 5548 during our campaign, the measured Hβ lag is a factor of five shorter than the expected value implied by the R BLR–L AGN relation based on the past behavior of NGC 5548.« less

SU-F-BRA-10: Fricke Dosimetry: Determination of the G-Value for Ir-192 Energy Based On the NRC Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salata, C; David, M; Rosado, P

Purpose: Use the methodology developed by the National Research Council Canada (NRC), for Fricke Dosimetry, to determine the G-value used at Ir-192 energies. Methods: In this study the Radiology Science Laboratory of Rio de Janeiro State University (LCR),based the G-value determination on the NRC method, using polyethylene bags. Briefly, this method consists of interpolating the G-values calculated for Co-60 and 250 kV x-rays for the average energy of Ir-192 (380 keV). As the Co-60 G-value is well described at literature, and associated with low uncertainties, it wasn’t measured in this present study. The G-values for 150 kV (Effective energy ofmore » 68 keV), 250 kV (Effective energy of 132 keV)and 300 kV(Effective energy of 159 keV)were calculated using the air kerma given by a calibrated ion chamber, and making it equivalent to the absorbed to the Fricke solution, using a Monte Carlo calculated factor for this conversion. Instead of interpolations, as described by the NRC, we displayed the G-values points in a graph, and used the line equation to determine the G- value for Ir-192 (380 keV). Results: The measured G-values were 1.436 ± 0.002 µmol/J for 150 kV, 1.472 ± 0.002 µmol/J for 250 kV, 1.497 ± 0.003 µmol/J for 300 kV. The used G-value for Co-60 (1.25 MeV) was 1,613 µmol/J. The R-square of the fitted regression line among those G-value points was 0.991. Using the line equation, the calculate G-value for 380 KeV was 1.542 µmol/J. Conclusion: The Result found for Ir-192 G-value is 3,1% different (lower) from the NRC value. But it agrees with previous literature results, using different methodologies to calculate this parameter. We will continue this experiment measuring the G-value for Co-60 in order to compare with the NRC method and better understand the reasons for the found differences.« less

Indole-based hydrazide-hydrazones and 4-thiazolidinones: synthesis and evaluation as antitubercular and anticancer agents.

PubMed

Cihan-Üstündağ, Gökçe; Şatana, Dilek; Özhan, Gül; Çapan, Gültaze

2016-01-01

A new series of indolylhydrazones (6) and indole-based 4-thiazolidinones (7, 8) have been designed, synthesized and screened for in vitro antitubercular activity against Mycobacterium tuberculosis H37Rv. 4-Thiazolidinone derivatives 7g-7j, 8g, 8h and 8j displayed notable antituberculosis (anti-TB) activity showing 99% inhibition at MIC values ranging from 6.25 to 25.0 µg/ml. Compounds 7g, 7h, 7i, 8h and 8j demonstrated anti-TB activity at concentrations 10-fold lower than those cytotoxic for the mammalian cell lines. The indolylhydrazone derivative 6b has also been evaluated for antiproliferative activity against human cancer cell lines at the National Cancer Institute (USA). Compound 6b showed an interesting anticancer profile against different human tumor-derived cell lines at sub-micromolar concentrations with obvious selectivity toward colon cancer cell line COLO 205.

Value-based purchasing of medical devices.

PubMed

Obremskey, William T; Dail, Teresa; Jahangir, A Alex

2012-04-01

Health care in the United States is known for its continued innovation and production of new devices and techniques. While the intention of these devices is to improve the delivery and outcome of patient care, they do not always achieve this goal. As new technologies enter the market, hospitals and physicians must determine which of these new devices to incorporate into practice, and it is important these devices bring value to patient care. We provide a model of a physician-engaged process to decrease cost and increase review of physician preference items. We describe the challenges, implementation, and outcomes of cost reduction and product stabilization of a value-based process for purchasing medical devices at a major academic medical center. We implemented a physician-driven committee that standardized and utilized evidence-based, clinically sound, and financially responsible methods for introducing or consolidating new supplies, devices, and technology for patient care. This committee worked with institutional finance and administrative leaders to accomplish its goals. Utilizing this physician-driven committee, we provided access to new products, standardized some products, decreased costs of physician preference items 11% to 26% across service lines, and achieved savings of greater than $8 million per year. The implementation of a facility-based technology assessment committee that critically evaluates new technology can decrease hospital costs on implants and standardize some product lines.

Universal Representation of the H-like Spectral Line Shapes

NASA Astrophysics Data System (ADS)

Bureyeva, L.

2009-05-01

A universal approach for the calculation of Rydberg atom line shapes in plasmas is developed. It is based on analytical formulas for the intensity distribution in radiation transitions n→n' between highly excited atomic states with large values of principal quantum numbers n, n'≫1, with Δ n = n-n'≪n, and on the Frequency Fluctuation Model (FFM) to account of electron and ion thermal motion effects. The theory allows to describe a transition from the static to the impact broadening domains for every hydrogen spectral line. A new approach to extremely fast line shape calculations with account of charged particle dynamic effect was proposed. The approach is based on the close analogy between the static-impact broadening transition in the spectral line shape theory and the Doppler-Lorentz broadening in the Dicke narrowing effect theory. The precision of the new approach was tested by the comparison of hydrogen-alpha and beta line shapes calculations with the FFM results. The excellent agreement was discovered, the computer time decreased two orders of magnitudes as compared with the FFM.

Evaluation of width and width uniformity of near-field electrospinning printed micro and sub-micrometer lines based on optical image processing

NASA Astrophysics Data System (ADS)

Zhao, Libo; Xia, Yong; Hebibul, Rahman; Wang, Jiuhong; Zhou, Xiangyang; Hu, Yingjie; Li, Zhikang; Luo, Guoxi; Zhao, Yulong; Jiang, Zhuangde

2018-03-01

This paper presents an experimental study using image processing to investigate width and width uniformity of sub-micrometer polyethylene oxide (PEO) lines fabricated by near-filed electrospinning (NFES) technique. An adaptive thresholding method was developed to determine the optimal gray values to accurately extract profiles of printed lines from original optical images. And it was proved with good feasibility. The mechanism of the proposed thresholding method was believed to take advantage of statistic property and get rid of halo induced errors. Triangular method and relative standard deviation (RSD) were introduced to calculate line width and width uniformity, respectively. Based on these image processing methods, the effects of process parameters including substrate speed (v), applied voltage (U), nozzle-to-collector distance (H), and syringe pump flow rate (Q) on width and width uniformity of printed lines were discussed. The research results are helpful to promote the NFES technique for fabricating high resolution micro and sub-micro lines and also helpful to optical image processing at sub-micro level.

A computer procedure to analyze seismic data to estimate outcome probabilities in oil exploration, with an initial application in the tabasco region of southeastern Mexico

NASA Astrophysics Data System (ADS)

Berlanga, Juan M.; Harbaugh, John W.

The Tabasco region contains a number of major oilfields, including some of the emerging "giant" oil fields which have received extensive publicity. Fields in the Tabasco region are associated with large geologic structures which are detected readily by seismic surveys. The structures seem to be associated with deepseated movement of salt, and they are complexly faulted. Some structures have as much as 1000 milliseconds relief of seismic lines. A study, interpreting the structure of the area, used initially only a fraction of the total seismic lines That part of Tabasco region that has been studied was surveyed with a close-spaced rectilinear network of seismic lines. A, interpreting the structure of the area, used initially only a fraction of the total seismic data available. The purpose was to compare "predictions" of reflection time based on widely spaced seismic lines, with "results" obtained along more closely spaced lines. This process of comparison simulates the sequence of events in which a reconnaissance network of seismic lines is used to guide a succession of progressively more closely spaced lines. A square gridwork was established with lines spaced at 10 km intervals, and using machine contour maps, compared the results with those obtained with seismic grids employing spacings of 5 and 2.5 km respectively. The comparisons of predictions based on widely spaced lines with observations along closely spaced lines provide information by which an error function can be established. The error at any point can be defined as the difference between the predicted value for that point, and the subsequently observed value at that point. Residuals obtained by fitting third-degree polynomial trend surfaces were used for comparison. The root mean square of the error measurement, (expressed in seconds or milliseconds reflection time) was found to increase more or less linearly with distance from the nearest seismic point. Oil-occurrence probabilities were established on the basis of frequency distributions of trend-surface residuals obtained by fitting and subtracting polynomial trend surfaces from the machine-contoured reflection time maps. We found that there is a strong preferential relationship between the occurrence of petroleum (i.e. its presence versus absence) and particular ranges of trend-surface residual values. An estimate of the probability of oil occurring at any particular geographic point can be calculated on the basis of the estimated trend-surface residual value. This estimate, however, must be tempered by the probable error in the estimate of the residual value provided by the error function. The result, we believe, is a simple but effective procedure for estimating exploration outcome probabilities where seismic data provide the principal form of information in advance of drilling. Implicit in this approach is the comparison between a maturely explored area, for which both seismic and production data are available, and which serves as a statistical "training area", with the "target" area which is undergoing exploration and for which probability forecasts are to be calculated.

Methods of Fitting a Straight Line to Data: Examples in Water Resources

USGS Publications Warehouse

Hirsch, Robert M.; Gilroy, Edward J.

1984-01-01

Three methods of fitting straight lines to data are described and their purposes are discussed and contrasted in terms of their applicability in various water resources contexts. The three methods are ordinary least squares (OLS), least normal squares (LNS), and the line of organic correlation (OC). In all three methods the parameters are based on moment statistics of the data. When estimation of an individual value is the objective, OLS is the most appropriate. When estimation of many values is the objective and one wants the set of estimates to have the appropriate variance, then OC is most appropriate. When one wishes to describe the relationship between two variables and measurement error is unimportant, then OC is most appropriate. Where the error is important in descriptive problems or in calibration problems, then structural analysis techniques may be most appropriate. Finally, if the problem is one of describing some geographic trajectory, then LNS is most appropriate.

A table of semiempirical gf values. Part 1: Wavelengths: 5.2682 nm to 272.3380 nm. [to calculate line-blanketed model atmospheres for solar and stellar spectra

NASA Technical Reports Server (NTRS)

Kurucz, R. L.; Peytremann, E.

1975-01-01

The gf values for 265,587 atomic lines selected from the line data used to calculate line-blanketed model atmospheres are tabulated. These data are especially useful for line identification and spectral synthesis in solar and stellar spectra. The gf values are calculated semiempirically by using scaled Thomas-Fermi-Dirac radial wavefunctions and eigenvectors found through least-squares fits to observed energy levels. Included in the calculation are the first five or six stages of ionization for sequences up through nickel. Published gf values are included for elements heavier than nickel. The tabulation is restricted to lines with wavelengths less than 10 micrometers.

An experimental water line list at 1950 K in the 6250-6670 cm-1 region

NASA Astrophysics Data System (ADS)

Rutkowski, Lucile; Foltynowicz, Aleksandra; Schmidt, Florian M.; Johansson, Alexandra C.; Khodabakhsh, Amir; Kyuberis, Aleksandra A.; Zobov, Nikolai F.; Polyansky, Oleg L.; Yurchenko, Sergei N.; Tennyson, Jonathan

2018-01-01

An absorption spectrum of H216O at 1950 K is recorded in a premixed methane/air flat flame using a cavity-enhanced optical frequency comb-based Fourier transform spectrometer. 2417 absorption lines are identified in the 6250-6670 cm-1 region with an accuracy of about 0.01 cm-1. Absolute line intensities are retrieved using temperature and concentration values obtained by tunable diode laser absorption spectroscopy. Line assignments are made using a combination of empirically known energy levels and predictions from the new POKAZATEL variational line list. 2030 of the observed lines are assigned to 2937 transitions, once blends are taken into account. 126 new energy levels of H216O are identified. The assigned transitions belong to 136 bands and span rotational states up to J = 27 .

Line transport in turbulent atmosphere

NASA Astrophysics Data System (ADS)

Nikoghossian, Artur

We consider the spectral line transfer in turbulent atmospheres with a spatially correlated velocity field. Both the finite and semi-infinite media are treated. In finding the observed intensities we first deal with the problem for determining the mean intensity of radiation emerging from the medium for a fixed value of turbulent velocity at its boundary. New approach proposed in solving this problem is based on invariant imbedding technique which yields the solution of the proper problems for a family of media of different optical thicknesses and allows tackling different kinds of inhomogeneous problems. The dependence of the line profile, integral intensity and the line width on the mean correlation length and average value of the hydrodynamic velocity is studied. It is shown that the transition from a micro-turbulent regime to a macro-turbulent one occurs within a comparatively narrow range of variation in the correlation length. The diffuse reflection of the line radiation from a one-dimensional semi-infinite turbulent atmosphere is examined. In addition to the observed spectral line profile, statistical averages describing the diffusion process in the atmosphere (mean number of scattering events, average time spent by a diffusing photon in the medium) are determined. The dependence of these quantities on the average hydrodynamic velocity and correlation coefficient is studied.

Line Transport in Turbulent Atmospheres

NASA Astrophysics Data System (ADS)

Nikoghossian, A. G.

2017-07-01

The spectral line transfer in turbulent atmospheres with a spatially correlated velocity field is examined. Both the finite and semi-infinite media are treated. In finding the observed intensities we first deal with the problem for determining the mean intensity of radiation emerging from the medium for a fixed value of turbulent velocity at its boundary. A new approach proposed for solving this problem is based on the invariant imbedding technique which yields the solution of the proper problems for a family of media of different optical thicknesses and allows tackling different kinds of inhomogeneous problems. The dependence of the line profile, integral intensity, and the line width on the mean correlation length and the average value of the hydrodynamic velocity is studied. It is shown that the transition from a micro-turbulent regime to a macro-turbulence occurs within a comparatively narrow range of variation in the correlation length . Ambartsumian's principle of invariance is used to solve the problem of diffuse reflection of the line radiation from a one-dimensional semi-infinite turbulent atmosphere. In addition to the observed spectral line profile, statistical averages describing the diffusion process in the atmosphere (mean number of scattering events, average time spent by a diffusing photon in the medium) are determined. The dependence of these quantities on the average hydrodynamic velocity and correlation coefficient is studied.

Control of motion stability of the line tracer robot using fuzzy logic and kalman filter

NASA Astrophysics Data System (ADS)

Novelan, M. S.; Tulus; Zamzami, E. M.

2018-03-01

Setting of motion and balance line tracer robot two wheels is actually a combination of a two-wheeled robot balance concept and the concept of line follower robot. The main objective of this research is to maintain the robot in an upright and can move to follow the line of the Wizard while maintaining balance. In this study the motion balance system on line tracer robot by considering the presence of a noise, so that it takes the estimator is used to mengestimasi the line tracer robot motion. The estimation is done by the method of Kalman Filter and the combination of Fuzzy logic-Fuzzy Kalman Filter called Kalman Filter, as well as optimal smooting. Based on the results of the study, the value of the output of the fuzzy results obtained from the sensor input value has been filtered before entering the calculation of the fuzzy. The results of the output of the fuzzy logic hasn’t been able to control dc motors are well balanced at the moment to be able to run. The results of the fuzzy logic by using membership function of triangular membership function or yet can control with good dc motor movement in order to be balanced

[Connotation characterization and evaluation of ecological well-being based on ecosystem service theory.

PubMed

Zang, Zheng; Zou, Xin- Qing

2016-04-22

China is advocating ecological civilization construction nowadays. Further researches on the relation between ecosystem service and humanity well-being are full of theoretical and practical significance. Combining related researches, this paper defined the concept and connotation of ecological well-being based on ecosystem service theory. Referencing theory of national economic accounting and relative researches, the evaluation indicators of ecological well-being supply and consumption were established. The quantitative characterization and evaluation method of red line of regional ecological well-being was proposed on the basis of location quotient. Then the evaluation of ecological well-being in mainland China in 2012 was set as an example for empirical research. The results showed that the net product values of 6 ecosystems, includingcultivated land, forest land, grassland, wetland, water area and unused land, were respectively 1481.925, 8194.806, 4176.277, 4245.760, 3177.084 and 133.762 billion CNY. Spatial heterogeneity of ecosystem net product in different provinces was distinct. Ecological well-being per capita of forest land, grassland, wetland, cultivated land and unused land in eastern and middle provinces were under the red line and less than the national average. The spatial distribution of 9 kinds of ecological well-being per capita split at Hu's line with high value in northwest and low value in southeast, and was aggravated by differences in density of population and land resources gift.

Asteroid mass estimation with Markov-chain Monte Carlo

NASA Astrophysics Data System (ADS)

Siltala, L.; Granvik, M.

2017-09-01

We have developed a new Markov-chain Monte Carlo-based algorithm for asteroid mass estimation based on mutual encounters and tested it for several different asteroids. Our results are in line with previous literature values but suggest that uncertainties of prior estimates may be misleading as a consequence of using linearized methods.

Circuit for Communication over DC Power Line Using High Temperature Electronics

NASA Technical Reports Server (NTRS)

Krasowski, Michael J. (Inventor); Prokop, Norman F. (Inventor)

2014-01-01

A high temperature communications circuit includes a power conductor for concurrently conducting electrical energy for powering circuit components and transmitting a modulated data signal, and a demodulator for demodulating the data signal and generating a serial bit stream based on the data signal. The demodulator includes an absolute value amplifier for conditionally inverting or conditionally passing a signal applied to the absolute value amplifier. The absolute value amplifier utilizes no diodes to control the conditional inversion or passing of the signal applied to the absolute value amplifier.

Full range line-field parallel swept source imaging utilizing digital refocusing

NASA Astrophysics Data System (ADS)

Fechtig, Daniel J.; Kumar, Abhishek; Drexler, Wolfgang; Leitgeb, Rainer A.

2015-12-01

We present geometric optics-based refocusing applied to a novel off-axis line-field parallel swept source imaging (LPSI) system. LPSI is an imaging modality based on line-field swept source optical coherence tomography, which permits 3-D imaging at acquisition speeds of up to 1 MHz. The digital refocusing algorithm applies a defocus-correcting phase term to the Fourier representation of complex-valued interferometric image data, which is based on the geometrical optics information of the LPSI system. We introduce the off-axis LPSI system configuration, the digital refocusing algorithm and demonstrate the effectiveness of our method for refocusing volumetric images of technical and biological samples. An increase of effective in-focus depth range from 255 μm to 4.7 mm is achieved. The recovery of the full in-focus depth range might be especially valuable for future high-speed and high-resolution diagnostic applications of LPSI in ophthalmology.

A Coastal Hazards Data Base for the U.S. West Coast (1997) (NDP-043C)

DOE Data Explorer

Gomitz, Vivien M. [Columbia Univ., New York, NY (United States); Beaty, Tammy W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Daniels, Richard C. [The University of Tennessee, Knoville, TN (United States)

1997-01-01

This data base integrates point, line, and polygon data for the U.S. West Coast into 0.25 degree latitude by 0.25 degree longitude grid cells and into 1:2,000,000 digitized line segments that can be used by raster or vector geographic information systems (GIS) as well as by non-GIS data bases. Each coastal grid cell and line segment contains data variables from the following seven data sets: elevation, geology, geomorphology, sea-level trends, shoreline displacement (erosion/accretion), tidal ranges, and wave heights. One variable from each data set was classified according to its susceptibility to sea-level rise and/or erosion to form 7 relative risk variables. These risk variables range in value from 1 to 5 and may be used to calculate a Coastal Vulnerability Index (CVI). Algorithms used to calculate several CVIs are listed within this text.

Expressing analytical performance from multi-sample evaluation in laboratory EQA.

PubMed

Thelen, Marc H M; Jansen, Rob T P; Weykamp, Cas W; Steigstra, Herman; Meijer, Ron; Cobbaert, Christa M

2017-08-28

To provide its participants with an external quality assessment system (EQAS) that can be used to check trueness, the Dutch EQAS organizer, Organization for Quality Assessment of Laboratory Diagnostics (SKML), has innovated its general chemistry scheme over the last decade by introducing fresh frozen commutable samples whose values were assigned by Joint Committee for Traceability in Laboratory Medicine (JCTLM)-listed reference laboratories using reference methods where possible. Here we present some important innovations in our feedback reports that allow participants to judge whether their trueness and imprecision meet predefined analytical performance specifications. Sigma metrics are used to calculate performance indicators named 'sigma values'. Tolerance intervals are based on both Total Error allowable (TEa) according to biological variation data and state of the art (SA) in line with the European Federation of Clinical Chemistry and Laboratory Medicine (EFLM) Milan consensus. The existing SKML feedback reports that express trueness as the agreement between the regression line through the results of the last 12 months and the values obtained from reference laboratories and calculate imprecision from the residuals of the regression line are now enriched with sigma values calculated from the degree to which the combination of trueness and imprecision are within tolerance limits. The information and its conclusion to a simple two-point scoring system are also graphically represented in addition to the existing difference plot. By adding sigma metrics-based performance evaluation in relation to both TEa and SA tolerance intervals to its EQAS schemes, SKML provides its participants with a powerful and actionable check on accuracy.

Impacts of Microphysical Scheme on Convective and Stratiform Characteristics in Two High Precipitation Squall Line Events

NASA Technical Reports Server (NTRS)

Wu, Di; Dong, Xiquan; Xi, Baike; Feng, Zhe; Kennedy, Aaron; Mullendore, Gretchen; Gilmore, Matthew; Tao, Wei-Kuo

2013-01-01

This study investigates the impact of snow, graupel, and hail processes on simulated squall lines over the Southern Great Plains in the United States. The Weather Research and Forecasting (WRF) model is used to simulate two squall line events in Oklahoma during May 2007, and the simulations are validated against radar and surface observations. Several microphysics schemes are tested in this study, including the WRF 5-Class Microphysics (WSM5), WRF 6-Class Microphysics (WSM6), Goddard Cumulus Ensemble (GCE) Three Ice (3-ice) with graupel, Goddard Two Ice (2-ice), and Goddard 3-ice hail schemes. Simulated surface precipitation is sensitive to the microphysics scheme when the graupel or hail categories are included. All of the 3-ice schemes overestimate the total precipitation with WSM6 having the largest bias. The 2-ice schemes, without a graupel/hail category, produce less total precipitation than the 3-ice schemes. By applying a radar-based convective/stratiform partitioning algorithm, we find that including graupel/hail processes increases the convective areal coverage, precipitation intensity, updraft, and downdraft intensities, and reduces the stratiform areal coverage and precipitation intensity. For vertical structures, simulations have higher reflectivity values distributed aloft than the observed values in both the convective and stratiform regions. Three-ice schemes produce more high reflectivity values in convective regions, while 2-ice schemes produce more high reflectivity values in stratiform regions. In addition, this study has demonstrated that the radar-based convective/stratiform partitioning algorithm can reasonably identify WRF-simulated precipitation, wind, and microphysical fields in both convective and stratiform regions.

Anticancer property of sediment actinomycetes against MCF-7 and MDA-MB-231 cell lines.

PubMed

Ravikumar, S; Fredimoses, M; Gnanadesigan, M

2012-02-01

To investigate the anticancer property of marine sediment actinomycetes against two different breast cancer cell lines. In vitro anticancer activity was carried out against breast (MCF-7 and MDA-MB-231) cancer cell lines. Partial sequences of the 16s rRNA gene, phylogenetic tree construction, multiple sequence analysis and secondary structure analysis were also carried out with the actinomycetes isolates. Of the selected five actinomycete isolates, ACT01 and ACT02 showed the IC50 value with (10.13±0.92) and (22.34±5.82) µg/mL concentrations, respectively for MCF-7 cell line at 48 h, but ACT01 showed the minimum (18.54±2.49 µg/mL) level of IC50 value with MDA-MB-231 cell line. Further, the 16s rRNA partial sequences of ACT01, ACT02, ACT03, ACT04 and ACT05 isolates were also deposited in NCBI data bank with the accession numbers of GQ478246, GQ478247, GQ478248, GQ478249 and GQ478250, respectively. The phylogenetic tree analysis showed that, the isolates of ACT02 and ACT03 were represented in group I and III, respectively, but ACT01 and ACT02 were represented in group II. The multiple sequence alignment of the actinomycete isolates showed that, the maximum identical conserved regions were identified with the nucleotide regions of 125 to 221st base pairs, 65 to 119th base pairs and 55, 48 and 31st base pairs. Secondary structure prediction of the 16s rRNA showed that, the maximum free energy was consumed with ACT03 isolate (-45.4 kkal/mol) and the minimum free energy was consumed with ACT04 isolate (-57.6 kkal/mol). The actinomycete isolates of ACT01 and ACT02 (GQ478246 and GQ478247) which are isolated from sediment sample can be further used as anticancer agents against breast cancer cell lines.

Structure Line Detection from LIDAR Point Clouds Using Topological Elevation Analysis

NASA Astrophysics Data System (ADS)

Lo, C. Y.; Chen, L. C.

2012-07-01

Airborne LIDAR point clouds, which have considerable points on object surfaces, are essential to building modeling. In the last two decades, studies have developed different approaches to identify structure lines using two main approaches, data-driven and modeldriven. These studies have shown that automatic modeling processes depend on certain considerations, such as used thresholds, initial value, designed formulas, and predefined cues. Following the development of laser scanning systems, scanning rates have increased and can provide point clouds with higher point density. Therefore, this study proposes using topological elevation analysis (TEA) to detect structure lines instead of threshold-dependent concepts and predefined constraints. This analysis contains two parts: data pre-processing and structure line detection. To preserve the original elevation information, a pseudo-grid for generating digital surface models is produced during the first part. The highest point in each grid is set as the elevation value, and its original threedimensional position is preserved. In the second part, using TEA, the structure lines are identified based on the topology of local elevation changes in two directions. Because structure lines can contain certain geometric properties, their locations have small relieves in the radial direction and steep elevation changes in the circular direction. Following the proposed approach, TEA can be used to determine 3D line information without selecting thresholds. For validation, the TEA results are compared with those of the region growing approach. The results indicate that the proposed method can produce structure lines using dense point clouds.

A candidate reference method using ICP-MS for sweat chloride quantification.

PubMed

Collie, Jake T; Massie, R John; Jones, Oliver A H; Morrison, Paul D; Greaves, Ronda F

2016-04-01

The aim of the study was to develop a method for sweat chloride (Cl) quantification using Inductively Coupled Plasma Mass Spectrometry (ICP-MS) to present to the Joint Committee for Traceability in Laboratory Medicine (JCTLM) as a candidate reference method for the diagnosis of cystic fibrosis (CF). Calibration standards were prepared from sodium chloride (NaCl) to cover the expected range of sweat Cl values. Germanium (Ge) and scandium (Sc) were selected as on-line (instrument based) internal standards (IS) and gallium (Ga) as the off-line (sample based) IS. The method was validated through linearity, accuracy and imprecision studies as well as enrolment into the Royal College of Pathologists of Australasia Quality Assurance Program (RCPAQAP) for sweat electrolyte testing. Two variations of the ICP-MS method were developed, an on-line and off-line IS, and compared. Linearity was determined up to 225 mmol/L with a limit of quantitation of 7.4 mmol/L. The off-line IS demonstrated increased accuracy through the RCPAQAP performance assessment (CV of 1.9%, bias of 1.5 mmol/L) in comparison to the on-line IS (CV of 8.0%, bias of 3.8 mmol/L). Paired t-tests confirmed no significant differences between sample means of the two IS methods (p=0.53) or from each method against the RCPAQAP target values (p=0.08 and p=0.29). Both on and off-line IS methods generated highly reproducible results and excellent linear comparison to the RCPAQAP target results. ICP-MS is a highly accurate method with a low limit of quantitation for sweat Cl analysis and should be recognised as a candidate reference method for the monitoring and diagnosis of CF. Laboratories that currently practice sweat Cl analysis using ICP-MS should include an off-line IS to help negate any pre-analytical errors.

'Ogura'-based 'CMS' lines with different nuclear backgrounds of cabbage revealed substantial diversity at morphological and molecular levels.

PubMed

Parkash, Chander; Kumar, Sandeep; Singh, Rajender; Kumar, Ajay; Kumar, Satish; Dey, Shyam Sundar; Bhatia, Reeta; Kumar, Raj

2018-01-01

A comprehensive study on characterization and genetic diversity analysis was carried out in 16 'Ogura'-based 'CMS' lines of cabbage using 14 agro-morphological traits and 29 SSR markers. Agro-morphological characterization depicted considerable variations for different horticultural traits studied. The genotype, ZHA-2, performed better for most of the economically important quantitative traits. Further, gross head weight (0.76), head length (0.60) and head width (0.83) revealed significant positive correlation with net head weight. Dendrogram based on 10 quantitative traits exhibited considerable diversity among different CMS lines and principle component analysis (PCA) indicated that net and gross head weight, and head length and width are the main components of divergence between 16 CMS lines of cabbage. In molecular study, a total of 58 alleles were amplified by 29 SSR primers, averaging to 2.0 alleles in each locus. High mean values of Shannon's Information index (0.62), expected (0.45) and observed (0.32) heterozygosity and polymorphic information content (0.35) depicted substantial polymorphism. Dendrogram based on Jaccard's similarity coefficient constructed two major groups and eight sub-groups, which revealed substantial diversity among different CMS lines. In overall, based on agro-morphological and molecular studies genotype RRMA, ZHA-2 and RCA were found most divergent. Hence, they have immense potential in future breeding programs for the high-yielding hybrid development in cabbage.

Cytotoxic constituents of propolis from Myanmar and their structure-activity relationship.

PubMed

Li, Feng; Awale, Suresh; Tezuka, Yasuhiro; Kadota, Shigetoshi

2009-12-01

Thirteen cycloartane-type tritepenes (1-13) and four prenylated flavanones (14-17) isolated from propolis collected in Myanmar, were evaluated for their cytotoxic activity against a panel of six different cancer cell lines; three murine cancer cell lines (colon 26-L5 carcinoma, B16-BL6 melanoma, and Lewis lung carcinoma) and three human cancer cell lines (lung A549 adenocarcinoma, cervix HeLa adenocarcinoma and HT-1080 fibrosarcoma). Among them, a cycloartane-type triterpene, 3alpha,27-dihydroxycycloart-24E-en-26-oic acid (3), showed the most potent cytotoxicity against B16-BL6 cells with an IC(50) value of 5.91 microM, comparable to those of positive controls, doxorubicin (IC(50), 5.66 microM) and 5-fluorouracil (IC(50), 4.88 microM). In addition, (2S)-5,7-dihydroxy-4'-methoxy-8,3'-diprenylflavanone (14) exhibited strong cytotoxicity against all the tested cancer cell lines with the IC(50) values ranging from 14.0 to 26.4 microM. Based on the observed results, the structure-activity relationships are discussed.

Characteristics of wettedness and equi-skin temperature line in the evaporative regulation region

NASA Astrophysics Data System (ADS)

Mochida, T.

1983-07-01

As a result of the analysis of physiological experimental data, the characteristics of the wettedness were clarified, i.e., the value of the wettedness is not constant but differs in accordance with the environmental humidity even when the skin temperature is the same, and it was shown that the evaporative heat loss from the skin surface is inversely proportional to the wetttedness. Based on the properties of the wetedness observed, a new thermal sensation chart in the evaporative regulation region was proposed as an index for evaluating the warmth or the coldness in the environment. The feature of the present chart is that the locus of the equal skin temperature appears as a curved line on the psychrometric chart and that the wettedness on the equi-skin temperature line is not constant but takes varying values. The curved equal skin temperature line means that the influence of the environmental humidity on thermal sensation becomes smaller as the humidity of the environmental humidity on thermal sensation becomes smaller as the humidity of the environment is lowered.

New isopimarane diterpenes and nortriterpene with cytotoxic activity from Ephorbia alatavica Boiss.

PubMed

Rozimamat, Rushangul; Hu, Rui; Aisa, Haji Akber

2018-06-01

Three new isopimarane diterpenes and one new nor-triterpenes, along with five known diterpenes were isolated from the whole areal part of Ephorbia alatavica Boiss. The structures of the new compounds (1-4) were determined based on extensive spectroscopic analysis, including HR-ESIMS, 1D and 2D NMR data. A plausible biosynthetic pathway for new compounds (1-4) were hypothesized. All isolated compounds were screen for cytotoxicity activity against MCF-8, HeLa and A549 cell lines in vitro by MTT assay. New compound 1 and known 9 showed potential cytotoxic activities with IC 50 values of 15.327 μg/mL, 23.066 μg/mL against MCF-8 cell lines, compound1 showed noteworthy cytotoxic activity with IC 50 13.033 μg/mL against A549 cancer cell line. New compounds 2, 4 and 4 showed moderate cytotoxic activities three human cancer lines with IC 50 value around 50 μg/mL, which compared with positive control doxorubicin (DOX). Copyright © 2018 Elsevier B.V. All rights reserved.

A table of semiempirical gf values. Part 2. Wavelengths: 272. 3395 nm to 599. 3892 nm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurucz, R.L.; Peytremann, E.

1975-02-14

The gf values for 265,587 atomic lines selectedfrom the line data used to calculate line blanketed model atmospheres are tabulated. These data are especially useful for line identification and spectral synthesis in solar and stellar spectra. The gf values are calculated semiempirically by using scaled Thomas--Fermi--Dirac radial wave functions and eigenvectors found through least-squares fits to observed energy levels. Included in the calculation are the first five or six stages of ionization for sequences up through nickel. Published gf values are included for elements heavier than nickel. The tabulation is restricted to lines with wavelengths less than 10 micrometers. (auth)

Semi-empirical calculations of line-shape parameters and their temperature dependences for the ν6 band of CH3D perturbed by N2

NASA Astrophysics Data System (ADS)

Dudaryonok, A. S.; Lavrentieva, N. N.; Buldyreva, J.

2018-06-01

(J, K)-line broadening and shift coefficients with their temperature-dependence characteristics are computed for the perpendicular (ΔK = ±1) ν6 band of the 12CH3D-N2 system. The computations are based on a semi-empirical approach which consists in the use of analytical Anderson-type expressions multiplied by a few-parameter correction factor to account for various deviations from Anderson's theory approximations. A mathematically convenient form of the correction factor is chosen on the basis of experimental rotational dependencies of line widths, and its parameters are fitted on some experimental line widths at 296 K. To get the unknown CH3D polarizability in the excited vibrational state v6 for line-shift calculations, a parametric vibration-state-dependent expression is suggested, with two parameters adjusted on some room-temperature experimental values of line shifts. Having been validated by comparison with available in the literature experimental values for various sub-branches of the band, this approach is used to generate massive data of line-shape parameters for extended ranges of rotational quantum numbers (J up to 70 and K up to 20) typically requested for spectroscopic databases. To obtain the temperature-dependence characteristics of line widths and line shifts, computations are done for various temperatures in the range 200-400 K recommended for HITRAN and least-squares fit procedures are applied. For the case of line widths strong sub-branch dependence with increasing K is observed in the R- and P-branches; for the line shifts such dependence is stated for the Q-branch.

Artificial Potential Field Controllers for Robust Communications in a Network of Swarm Robots

DTIC Science & Technology

2005-05-18

vectors are less than 90◦ apart. Algorithm 1 The Algorithm for generating a feasible set of vectors P ← set of high priority vectors Csum ← [( LOS1 +R1...the 46 C program was finished reading and writing the values to the serial line it would delete the timing file. Only after the timing file had been... deleted would the base station write new values for the wheel velocities. The timing file kept both the Linux PC and the base station synchronized so

Cost-outcomes focus is essential for ACO success.

PubMed

Greenspun, Harry; Bercik, William

2013-02-01

To succeed under value-based payment, accountable care organizations (ACOs) must be able to link, analyze, and compare clinical and administrative data from across their constituent organizations. ACOs require a precise costing methodology, such as activity-based costing, to be able to manage costs effectively and gain critical insight into which service lines are delivering value from a clinical and financial standpoint. To support informed strategic decision-making, ACOs also require ready access to integrated patient encounter data to be able to perform the sophisticated modeling of predictive analytics.

A new method to measure the virial factors in the reverberation mapping of active galactic nuclei

NASA Astrophysics Data System (ADS)

Liu, H. T.; Feng, H. C.; Bai, J. M.

2017-04-01

Based on the gravitational red shift, which is a prediction of Einstein's general relativity theory, of broad optical emission lines in active galactic nuclei (AGNs), a new method is proposed to estimate the virial factors f in measuring black hole masses MRM by the reverberation mapping of AGNs. The factors f can be measured based on two physical quantities, I.e. the gravitational red shifts zg and the full widths at half maxima vFWHM of broad lines. In the past, it has been difficult to determine the factors f for individual AGNs. We apply this new method to several reverberation-mapped type 1 Seyfert galaxies. There is a correlation between f and the radius of the broad-line region (BLR) rBLR, f=5.4 r_{BLR}^{0.3}, for the gravitationally red-shifted broad lines He II, He I, Hβ and Hα in the narrow-line type 1 Seyfert galaxy (NLS1) Mrk 110. This correlation results from the influence of the radiation pressure of the accretion disc on the BLR clouds. This influence seems to be more important than usually thought so in AGNs. Mrk 110 has f ≈ 8-16, distinctly larger than the mean ≈ 1 usually used to estimate MRM for vFWHM. NGC 4593 and NLS1 Mrk 486 have f ≈ 3 and f ≈ 9, respectively. Higher f values of several tens are derived for three other NLS1s. There is a correlation between f and accretion rate dot{M}_{f=1}, f=6.8dot{M}^{0.4}_{f=1} for five objects, where dot{M}_{f=1}=dot{M}_{bullet }/L_{Edd}c^{-2} as f = 1 is assumed when estimating MRM used in the Eddington luminosity LEdd, dot{M}_{bullet } is the mass accretion rate, and c is the speed of light. These larger f values will produce higher MRM values and lower Eddington ratios.

Quantum key distribution using gaussian-modulated coherent states

NASA Astrophysics Data System (ADS)

Grosshans, Frédéric; Van Assche, Gilles; Wenger, Jérôme; Brouri, Rosa; Cerf, Nicolas J.; Grangier, Philippe

2003-01-01

Quantum continuous variables are being explored as an alternative means to implement quantum key distribution, which is usually based on single photon counting. The former approach is potentially advantageous because it should enable higher key distribution rates. Here we propose and experimentally demonstrate a quantum key distribution protocol based on the transmission of gaussian-modulated coherent states (consisting of laser pulses containing a few hundred photons) and shot-noise-limited homodyne detection; squeezed or entangled beams are not required. Complete secret key extraction is achieved using a reverse reconciliation technique followed by privacy amplification. The reverse reconciliation technique is in principle secure for any value of the line transmission, against gaussian individual attacks based on entanglement and quantum memories. Our table-top experiment yields a net key transmission rate of about 1.7 megabits per second for a loss-free line, and 75 kilobits per second for a line with losses of 3.1dB. We anticipate that the scheme should remain effective for lines with higher losses, particularly because the present limitations are essentially technical, so that significant margin for improvement is available on both the hardware and software.

Verification of the H2O Linelists with Theoretically Developed Tools

NASA Technical Reports Server (NTRS)

Ma, Qiancheng; Tipping, R.; Lavrentieva, N. N.; Dudaryonok, A. S.

2013-01-01

Two basic rules (i.e., the pair identity and the smooth variation rules) resulting from the properties of the energy levels and wave functions of H2O states govern how the spectroscopic parameters vary with the H2O lines within the individually defined groups of lines. With these rules, for those lines involving high j states in the same groups, variations of all their spectroscopic parameters (i.e., the transition frequency, intensity, pressure broadened half-width, pressure-induced shift, and temperature exponent) can be well monitored. Thus, the rules can serve as simple and effective tools to screen the H2O spectroscopic data listed in the HITRAN database and verify the latter's accuracies. By checking violations of the rules occurring among the data within the individual groups, possible errors can be picked up and also possible missing lines in the linelist whose intensities are above the threshold can be identified. We have used these rules to check the accuracies of the spectroscopic parameters and the completeness of the linelists for several important H2O vibrational bands. Based on our results, the accuracy of the line frequencies in HITRAN 2008 is consistent. For the line intensity, we have found that there are a substantial number of lines whose intensity values are questionable. With respect to other parameters, many mistakes have been found. The above claims are consistent with a well known fact that values of these parameters in HITRAN contain larger uncertainties. Furthermore, supplements of the missing line list consisting of line assignments and positions can be developed from the screening results.

Characterization of palmprints by wavelet signatures via directional context modeling.

PubMed

Zhang, Lei; Zhang, David

2004-06-01

The palmprint is one of the most reliable physiological characteristics that can be used to distinguish between individuals. Current palmprint-based systems are more user friendly, more cost effective, and require fewer data signatures than traditional fingerprint-based identification systems. The principal lines and wrinkles captured in a low-resolution palmprint image provide more than enough information to uniquely identify an individual. This paper presents a palmprint identification scheme that characterizes a palmprint using a set of statistical signatures. The palmprint is first transformed into the wavelet domain, and the directional context of each wavelet subband is defined and computed in order to collect the predominant coefficients of its principal lines and wrinkles. A set of statistical signatures, which includes gravity center, density, spatial dispersivity and energy, is then defined to characterize the palmprint with the selected directional context values. A classification and identification scheme based on these signatures is subsequently developed. This scheme exploits the features of principal lines and prominent wrinkles sufficiently and achieves satisfactory results. Compared with the line-segments-matching or interesting-points-matching based palmprint verification schemes, the proposed scheme uses a much smaller amount of data signatures. It also provides a convenient classification strategy and more accurate identification.

Mathematical simulation of sound propagation in a flow channel with impedance walls

NASA Astrophysics Data System (ADS)

Osipov, A. A.; Reent, K. S.

2012-07-01

The paper considers the specifics of calculating tonal sound propagating in a flow channel with an installed sound-absorbing device. The calculation is performed on the basis of numerical integrating on linearized nonstationary Euler equations using a code developed by the authors based on the so-called discontinuous Galerkin method. Using the linear theory of small perturbations, the effect of the sound-absorbing lining of the channel walls is described with the modified value of acoustic impedance proposed by the authors, for which, under flow channel conditions, the traditional classification of the active and reactive types of lining in terms of the real and imaginary impedance values, respectively, remains valid. To stabilize the computation process, a generalized impedance boundary condition is proposed in which, in addition to the impedance value itself, some additional parameters are introduced characterizing certain fictitious properties of inertia and elasticity of the impedance surface.

Proton irradiation studies on Al and Al5083 alloy

NASA Astrophysics Data System (ADS)

Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

2017-10-01

The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

Absolute instability of the Gaussian wake profile

NASA Technical Reports Server (NTRS)

Hultgren, Lennart S.; Aggarwal, Arun K.

1987-01-01

Linear parallel-flow stability theory has been used to investigate the effect of viscosity on the local absolute instability of a family of wake profiles with a Gaussian velocity distribution. The type of local instability, i.e., convective or absolute, is determined by the location of a branch-point singularity with zero group velocity of the complex dispersion relation for the instability waves. The effects of viscosity were found to be weak for values of the wake Reynolds number, based on the center-line velocity defect and the wake half-width, larger than about 400. Absolute instability occurs only for sufficiently large values of the center-line wake defect. The critical value of this parameter increases with decreasing wake Reynolds number, thereby indicating a shrinking region of absolute instability with decreasing wake Reynolds number. If backflow is not allowed, absolute instability does not occur for wake Reynolds numbers smaller than about 38.

Value-based attentional capture influences context-dependent decision-making

PubMed Central

Cha, Kexin; Rangsipat, Napat; Serences, John T.

2015-01-01

Normative theories posit that value-based decision-making is context independent. However, decisions between two high-value options can be suboptimally biased by the introduction of a third low-value option. This context-dependent modulation is consistent with the divisive normalization of the value of each stimulus by the total value of all stimuli. In addition, an independent line of research demonstrates that pairing a stimulus with a high-value outcome can lead to attentional capture that can mediate the efficiency of visual information processing. Here we tested the hypothesis that value-based attentional capture interacts with value-based normalization to influence the optimality of decision-making. We used a binary-choice paradigm in which observers selected between two targets and the color of each target indicated the magnitude of their reward potential. Observers also had to simultaneously ignore a task-irrelevant distractor rendered in a color that was previously associated with a specific reward magnitude. When the color of the task-irrelevant distractor was previously associated with a high reward, observers responded more slowly and less optimally. Moreover, as the learned value of the distractor increased, electrophysiological data revealed an attenuation of the lateralized N1 and N2Pc responses evoked by the relevant choice stimuli and an attenuation of the late positive deflection (LPD). Collectively, these behavioral and electrophysiological data suggest that value-based attentional capture and value-based normalization jointly mediate the influence of context on free-choice decision-making. PMID:25995350

Value-based attentional capture influences context-dependent decision-making.

PubMed

Itthipuripat, Sirawaj; Cha, Kexin; Rangsipat, Napat; Serences, John T

2015-07-01

Normative theories posit that value-based decision-making is context independent. However, decisions between two high-value options can be suboptimally biased by the introduction of a third low-value option. This context-dependent modulation is consistent with the divisive normalization of the value of each stimulus by the total value of all stimuli. In addition, an independent line of research demonstrates that pairing a stimulus with a high-value outcome can lead to attentional capture that can mediate the efficiency of visual information processing. Here we tested the hypothesis that value-based attentional capture interacts with value-based normalization to influence the optimality of decision-making. We used a binary-choice paradigm in which observers selected between two targets and the color of each target indicated the magnitude of their reward potential. Observers also had to simultaneously ignore a task-irrelevant distractor rendered in a color that was previously associated with a specific reward magnitude. When the color of the task-irrelevant distractor was previously associated with a high reward, observers responded more slowly and less optimally. Moreover, as the learned value of the distractor increased, electrophysiological data revealed an attenuation of the lateralized N1 and N2Pc responses evoked by the relevant choice stimuli and an attenuation of the late positive deflection (LPD). Collectively, these behavioral and electrophysiological data suggest that value-based attentional capture and value-based normalization jointly mediate the influence of context on free-choice decision-making. Copyright © 2015 the American Physiological Society.

Experimental transition probabilities for Mn II spectral lines

NASA Astrophysics Data System (ADS)

Manrique, J.; Aguilera, J. A.; Aragón, C.

2018-06-01

Transition probabilities for 46 spectral lines of Mn II with wavelengths in the range 2000-3500 Å have been measured by CSigma laser-induced breakdown spectroscopy (Cσ-LIBS). For 28 of the lines, experimental data had not been reported previously. The Cσ-LIBS method, based in the construction of generalized curves of growth called Cσ graphs, avoids the error due to self-absorption. The samples used to generate the laser-induced plasmas are fused glass disks prepared from pure MnO. The Mn concentrations in the samples and the lines included in the study are selected to ensure the validity of the model of homogeneous plasma used. The results are compared to experimental and theoretical values available in the literature.

The effect of automobile exhaust particulates on cell viability, plating efficiency and cell division of mammalian tissue culture cells.

PubMed

Seemayer, N H; Hadnagy, W; Tomingas, R

1987-03-01

Extract of particulate matter (EPM) of gasoline engine exhaust induced only a slight loss of cell viability of mouse macrophages (line IC-21) in vitro, while a strong dose-dependent reduction of plating efficiency of human cell line A-549 and of Syrian hamster line 14-1b occurred. Cytological investigations of exposed macrophages of line IC-21 revealed an increase in the mitotic index from 1.5% of control values up to 14.6% at the highest tested concentration of EPM. Mitotic arrest is based almost exclusively on C-type mitoses occurring dose-dependently in the presence of EPM. Results indicate disturbances of the spindle apparatus in the presence of EPM.

System for memorizing maximum values

NASA Technical Reports Server (NTRS)

Bozeman, Richard J., Jr. (Inventor)

1992-01-01

The invention discloses a system capable of memorizing maximum sensed values. The system includes conditioning circuitry which receives the analog output signal from a sensor transducer. The conditioning circuitry rectifies and filters the analog signal and provides an input signal to a digital driver, which may be either linear or logarithmic. The driver converts the analog signal to discrete digital values, which in turn triggers an output signal on one of a plurality of driver output lines n. The particular output lines selected is dependent on the converted digital value. A microfuse memory device connects across the driver output lines, with n segments. Each segment is associated with one driver output line, and includes a microfuse that is blown when a signal appears on the associated driver output line.

System for memorizing maximum values

NASA Astrophysics Data System (ADS)

Bozeman, Richard J., Jr.

1992-08-01

The invention discloses a system capable of memorizing maximum sensed values. The system includes conditioning circuitry which receives the analog output signal from a sensor transducer. The conditioning circuitry rectifies and filters the analog signal and provides an input signal to a digital driver, which may be either linear or logarithmic. The driver converts the analog signal to discrete digital values, which in turn triggers an output signal on one of a plurality of driver output lines n. The particular output lines selected is dependent on the converted digital value. A microfuse memory device connects across the driver output lines, with n segments. Each segment is associated with one driver output line, and includes a microfuse that is blown when a signal appears on the associated driver output line.

System for Memorizing Maximum Values

NASA Technical Reports Server (NTRS)

Bozeman, Richard J., Jr. (Inventor)

1996-01-01

The invention discloses a system capable of memorizing maximum sensed values. The system includes conditioning circuitry which receives the analog output signal from a sensor transducer. The conditioning circuitry rectifies and filters the analog signal and provides an input signal to a digital driver, which may be either liner or logarithmic. The driver converts the analog signal to discrete digital values, which in turn triggers an output signal on one of a plurality of driver output lines n. The particular output lines selected is dependent on the converted digital value. A microfuse memory device connects across the driver output lines, with n segments. Each segment is associated with one driver output line, and includes a microfuse that is blown when a signal appears on the associated driver output line.

[Gas Concentration Measurement Based on the Integral Value of Absorptance Spectrum].

PubMed

Liu, Hui-jun; Tao, Shao-hua; Yang, Bing-chu; Deng, Hong-gui

2015-12-01

The absorptance spectrum of a gas is the basis for the qualitative and quantitative analysis of the gas by the law of the Lambert-Beer. The integral value of the absorptance spectrum is an important parameter to describe the characteristics of the gas absorption. Based on the measured absorptance spectrum of a gas, we collected the required data from the database of HIT-RAN, and chose one of the spectral lines and calculated the integral value of the absorptance spectrum in the frequency domain, and then substituted the integral value into Lambert-Beer's law to obtain the concentration of the detected gas. By calculating the integral value of the absorptance spectrum we can avoid the more complicated calculation of the spectral line function and a series of standard gases for calibration, so the gas concentration measurement will be simpler and faster. We studied the changing trends of the integral values of the absorptance spectrums versus temperature. Since temperature variation would cause the corresponding variation in pressure, we studied the changing trends of the integral values of the absorptance spectrums versus both the pressure not changed with temperature and changed with the temperature variation. Based on the two cases, we found that the integral values of the absorptance spectrums both would firstly increase, then decrease, and finally stabilize with temperature increasing, but the ranges of specific changing trend were different in the two cases. In the experiments, we found that the relative errors of the integrated values of the absorptance spectrum were much higher than 1% and still increased with temperature when we only considered the change of temperature and completely ignored the pressure affected by the temperature variation, and the relative errors of the integrated values of the absorptance spectrum were almost constant at about only 1% when we considered that the pressure were affected by the temperature variation. As the integral value of the absorptance spectrum varied with temperature and the calculating error for the integral value fluctuates with ranges of temperature, in the gas measurement when we usd integral values of the absoptance spectrum, we should select a suitable temperature variation and obtain a more accurate measurement result.

A physical classification scheme for blazars

NASA Astrophysics Data System (ADS)

Landt, Hermine; Padovani, Paolo; Perlman, Eric S.; Giommi, Paolo

2004-06-01

Blazars are currently separated into BL Lacertae objects (BL Lacs) and flat spectrum radio quasars based on the strength of their emission lines. This is performed rather arbitrarily by defining a diagonal line in the Ca H&K break value-equivalent width plane, following Marchã et al. We readdress this problem and put the classification scheme for blazars on firm physical grounds. We study ~100 blazars and radio galaxies from the Deep X-ray Radio Blazar Survey (DXRBS) and 2-Jy radio survey and find a significant bimodality for the narrow emission line [OIII]λ5007. This suggests the presence of two physically distinct classes of radio-loud active galactic nuclei (AGN). We show that all radio-loud AGN, blazars and radio galaxies, can be effectively separated into weak- and strong-lined sources using the [OIII]λ5007-[OII]λ3727 equivalent width plane. This plane allows one to disentangle orientation effects from intrinsic variations in radio-loud AGN. Based on DXRBS, the strongly beamed sources of the new class of weak-lined radio-loud AGN are made up of BL Lacs at the ~75 per cent level, whereas those of the strong-lined radio-loud AGN include mostly (~97 per cent) quasars.

Experimental Investigation of two-phase nitrogen Cryo transfer line

NASA Astrophysics Data System (ADS)

Singh, G. K.; Nimavat, H.; Panchal, R.; Garg, A.; Srikanth, GLN; Patel, K.; Shah, P.; Tanna, V. L.; Pradhan, S.

2017-02-01

A 6-m long liquid nitrogen based cryo transfer line has been designed, developed and tested at IPR. The test objectives include the thermo-hydraulic characteristics of Cryo transfer line under single phase as well as two phase flow conditions. It is always easy in experimentation to investigate the thermo-hydraulic parameters in case of single phase flow of cryogen but it is real challenge when one deals with the two phase flow of cryogen due to availibity of mass flow measurements (direct) under two phase flow conditions. Established models have been reported in the literature where one of the well-known model of Lockhart-Martenelli relationship has been used to determine the value of quality at the outlet of Cryo transfer line. Under homogenous flow conditions, by taking the ratio of the single-phase pressure drop and the two-phase pressure drop, we estimated the quality at the outlet. Based on these equations, vapor quality at the outlet of the transfer line was predicted at different heat loads. Experimental rresults shown that from inlet to outlet, there is a considerable increment in the pressure drop and vapour quality of the outlet depending upon heat load and mass flow rate of nitrogen flowing through the line.

Extrapolation of Functions of Many Variables by Means of Metric Analysis

NASA Astrophysics Data System (ADS)

Kryanev, Alexandr; Ivanov, Victor; Romanova, Anastasiya; Sevastianov, Leonid; Udumyan, David

2018-02-01

The paper considers a problem of extrapolating functions of several variables. It is assumed that the values of the function of m variables at a finite number of points in some domain D of the m-dimensional space are given. It is required to restore the value of the function at points outside the domain D. The paper proposes a fundamentally new method for functions of several variables extrapolation. In the presented paper, the method of extrapolating a function of many variables developed by us uses the interpolation scheme of metric analysis. To solve the extrapolation problem, a scheme based on metric analysis methods is proposed. This scheme consists of two stages. In the first stage, using the metric analysis, the function is interpolated to the points of the domain D belonging to the segment of the straight line connecting the center of the domain D with the point M, in which it is necessary to restore the value of the function. In the second stage, based on the auto regression model and metric analysis, the function values are predicted along the above straight-line segment beyond the domain D up to the point M. The presented numerical example demonstrates the efficiency of the method under consideration.

Reactive power compensator

DOEpatents

El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Reactive Power Compensator.

DOEpatents

El-Sharkawi, M.A.; Venkata, S.S.; Chen, M.; Andexler, G.; Huang, T.

1992-07-28

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation. 26 figs.

Tri-state logic circuit

NASA Technical Reports Server (NTRS)

Pryor, Richard Lee (Inventor)

1977-01-01

A line driver including a pair of complementary transistors having their conduction paths serially connected between an operating and a reference potential and their bases connected through a first switch to a signal input terminal. A second switch is connected between the common base connection and the common connection of the conduction paths. With the second switch open and the first closed, an output voltage, responsive to the input signal, corresponding to first or second binary values is obtained. When the second switch is closed and the first opened, the transistor pair is turned off, disconnecting the line driver from its load, thereby providing tri-state logic operation.

Accurate oscillator strengths for interstellar ultraviolet lines of Cl I

NASA Technical Reports Server (NTRS)

Schectman, R. M.; Federman, S. R.; Beideck, D. J.; Ellis, D. J.

1993-01-01

Analyses on the abundance of interstellar chlorine rely on accurate oscillator strengths for ultraviolet transitions. Beam-foil spectroscopy was used to obtain f-values for the astrophysically important lines of Cl I at 1088, 1097, and 1347 A. In addition, the line at 1363 A was studied. Our f-values for 1088, 1097 A represent the first laboratory measurements for these lines; the values are f(1088)=0.081 +/- 0.007 (1 sigma) and f(1097) = 0.0088 +/- 0.0013 (1 sigma). These results resolve the issue regarding the relative strengths for 1088, 1097 A in favor of those suggested by astronomical measurements. For the other lines, our results of f(1347) = 0.153 +/- 0.011 (1 sigma) and f(1363) = 0.055 +/- 0.004 (1 sigma) are the most precisely measured values available. The f-values are somewhat greater than previous experimental and theoretical determinations.

Optical Fiber On-Line Detection System for Non-Touch Monitoring Roller Shape

NASA Astrophysics Data System (ADS)

Guo, Y.; Wang, Y. T.

2006-10-01

Basing on the principle of reflective displacement fiber-optic sensor, a high accuracy non-touch on-line optical fiber measurement system for roller shape is presented. The principle and composition of the detection system and the operation process are expatiated also. By using a novel probe of three optical fibers in equal transverse space, the effects of fluctuations in the light source, reflective changing of target surface and the intensity losses in the fiber lines are automatically compensated. Meantime, an optical fiber sensor model of correcting static error based on BP artificial neural network (ANN) is set up. Also by using interpolation method and value filtering to process the signals, effectively reduce the influence of random noise and the vibration of the roller bearing. So enhance the accuracy and resolution remarkably. Experiment proves that the accuracy of the system reach to the demand of practical production process, it provides a new method for the high speed, accurate and automatic on line detection of the mill roller shape.

High accuracy line positions of the ν1 fundamental band of 14N216O

NASA Astrophysics Data System (ADS)

AlSaif, Bidoor; Lamperti, Marco; Gatti, Davide; Laporta, Paolo; Fermann, Martin; Farooq, Aamir; Lyulin, Oleg; Campargue, Alain; Marangoni, Marco

2018-05-01

The ν1 fundamental band of N2O is examined by a novel spectrometer that relies on the frequency locking of an external-cavity quantum cascade laser around 7.8 μm to a near-infrared Tm:based frequency comb at 1.9 μm. Due to the large tunability, nearly 70 lines in the 1240-1310 cm-1 range of the ν1 band of N2O, from P(40) to R(31), are for the first time measured with an absolute frequency calibration and an uncertainty from 62 to 180 kHz, depending on the line. Accurate values of the spectroscopic constants of the upper state are derived from a fit of the line centers (rms ≈ 4.8 × 10-6 cm-1 or 144 kHz). The ν1 transitions presently measured in a Doppler regime validate high accuracy predictions based on sub-Doppler measurements of the ν3 and ν3-ν1 transitions.

Abundance analysis of neodymium in the solar atmosphere

NASA Astrophysics Data System (ADS)

Abdelkawy, Ali G. A.; Shaltout, Abdelrazek M. K.; Beheary, M. M.; Bakry, A.

2017-10-01

Based on non-local thermodynamical equilibrium (NLTE) calculations, the solar neodymium (Nd) content was found based on a model atom of singly ionized neodymium (Nd II) containing 153 energy levels and 42 line transitions plus the ground state of Nd III. Here, we re-derive the solar Nd abundance using the model of the solar photosphere of Holweger & Müller.We succeed in selecting a good sample line list, relying on 20 Nd II solar lines together with the most accurate transition probabilities measured experimentally and available observational data. With damping parameters obtained from the literature, we find a mean NLTE solar photospheric Nd abundance of log ɛNd(1D) = 1.43 ± 0.16, which is in excellent agreement with the meteoritic value (log ɛNd = 1.45 ± 0.02). For a set of selected Nd II lines, the NLTE abundance correction is found to be +0.01 dex compared with the standard LTE effect. The influence of collisional interactions with electrons and neutral hydrogen atoms is investigated in detail.

Investigations regarding the drag characteristics of flow-disturbing bodies which are arranged in line and attached to the wall

NASA Technical Reports Server (NTRS)

Balkowski, M.; Schollmeyer, H.

1980-01-01

The flow characteristics of rectangular bodies mounted on the base area of a rectangular closed wind tunnel are investigated. As many as four bodies are mounted in line with equal distances between successive bodies. The Mach number of the flowing air is in the range from 0.1 to 0.5. Total and individual drag values could be charged within a wide range by a suitable selection of the distance between successive bodies.

Anti-proliferative activity of 2,6-dichloro-9- or 7-(ethoxycarbonylmethyl)-9H- or 7H-purines against several human solid tumour cell lines.

PubMed

Morales, Fátima; Ramírez, Alberto; Conejo-García, Ana; Morata, Cynthia; Marchal, Juan A; Campos, Joaquín M

2014-04-09

As leads we took several benzo-fused seven- and six-membered scaffolds linked to the pyrimidine or purine moieties with notable anti-proliferative activity against human breast, colon and melanoma cancerous cell lines. We then decided to maintain the double-ringed nitrogenous bases and change the other components to the ethyl acetate moiety. This way six purine and two 5-fluorouracil derivatives were obtained and evaluated against the MCF-7, HCT-116, A-375 and G-361 cancer cell lines. Two QSARs are obtained between the anti-proliferative IC₅₀ values for compounds 26-33 and the clog P against the melanoma cell lines A-375 and G-361. Our results show that two of the analogues [ethyl 2-(2,6-dichloro-9H- or 7H-purine-9- or 7-yl)acetates (30 and 33, respectively)] are potent cytotoxic agents against all the tumour cell lines assayed, showing single-digit micromolar IC₅₀ values. This exemplifies the potential of our previously reported purine compounds to qualify as lead structures for medicinal chemistry campaigns, affording simplified analogues easy to synthesize and with a noteworthy bioactivity. The selective activity of 30 and 33 against the melanoma cell line A-375, via apoptosis, supposes a great advantage for a future therapeutic use. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

The influence of microstructure on the probability of early failure in aluminum-based interconnects

NASA Astrophysics Data System (ADS)

Dwyer, V. M.

2004-09-01

For electromigration in short aluminum interconnects terminated by tungsten vias, the well known "short-line" effect applies. In a similar manner, for longer lines, early failure is determined by a critical value Lcrit for the length of polygranular clusters. Any cluster shorter than Lcrit is "immortal" on the time scale of early failure where the figure of merit is not the standard t50 value (the time to 50% failures), but rather the total probability of early failure, Pcf. Pcf is a complex function of current density, linewidth, line length, and material properties (the median grain size d50 and grain size shape factor σd). It is calculated here using a model based around the theory of runs, which has proved itself to be a useful tool for assessing the probability of extreme events. Our analysis shows that Pcf is strongly dependent on σd, and a change in σd from 0.27 to 0.5 can cause an order of magnitude increase in Pcf under typical test conditions. This has implications for the web-based two-dimensional grain-growth simulator MIT/EmSim, which generates grain patterns with σd=0.27, while typical as-patterned structures are better represented by a σd in the range 0.4 - 0.6. The simulator will consequently overestimate interconnect reliability due to this particular electromigration failure mode.

PML expression in soft tissue sarcoma: prognostic and predictive value in alkylating agents/antracycline-based first line therapy.

PubMed

Vincenzi, Bruno; Santini, Daniele; Schiavon, Gaia; Frezza, Anna Maria; Silletta, Marianna; Crucitti, Pierfilippo; Casali, Paolo; Dei Tos, Angelo P; Rossi, Sabrina; Rizzo, Sergio; Badalamenti, Giuseppe; Tomasino, Rosa Maria; Russo, Antonio; Butrynski, James E; Tonini, Giuseppe

2012-04-01

Soft tissue sarcomas are aggressive tumors representing <1% of all adult neoplasms. Aim of our study was to evaluate promyelocytic leukemia gene expression value as prognostic factor and as a factor predicting response to alkylating agents/antracycline-based first line therapy. One hundred eleven patients affected by locally advanced and metastatic soft tissue sarcoma were selected. PML expression was evaluated by immunohistochemical analysis in pathological samples and in the corresponding normal tissue from each case. PML immunohistochemical results were correlated with prognosis and with radiological response to alkylating agents/antracycline-based first line therapy. PML expression was significantly reduced in synovial sarcomas (P < 0.0001), in myofibroblastic sarcomas (P < 0.0001), angiosarcomas (P < 0.0001), in leiomyosarcomas (P = 0.003), in mixoid liposarcomas (P < 0.0001), and in dedifferentiated liposarcomas (P < 0.0001). No significant difference was found for pleomorphic sarcoma [31.8 (95% CI: 16.7-41.0); P = 0.21]. and pleomorphic liposarcomas (P = 0.51). Loss of PML expression was found to be statistically correlated with TTP (P < 0.0001), median duration of response (P = 0.007), and OS (P = 0.02). No correlation was observed between PML expression and treatment efficacy. PML IHC expression is down-regulated in synovial sarcomas, myofibroblastic sarcomas, angiosarcomas, liposarcoma, and leiomyosarcomas and its expression correlated with prognosis. Copyright © 2011 Wiley Periodicals, Inc.

Vega: A rapidly rotating pole-on star

NASA Technical Reports Server (NTRS)

Gulliver, Austin F.; Hill, Graham; Adelman, Saul J.

1994-01-01

High-dispersion (2.4 A/mm), ultrahigh signal-to-noise ratio (3000:1) Reticon spectra of Vega revealed two distinct types of profiles. The strong lines exhibit classical rotational profiles with enhanced wings, but the weak lines have distinctly different, flat-bottomed profiles. Using ATLAS9 model atmopheres and SYNTHE synthetic spectra, Vega has been modeled as a rapidly rotating, pole-on star with a gradient in temperature and gravity over the photosphere. By fitting to the flat-bottomed line profiles of Fe 1 lambda 4528 and Ti 2 lambda 4529, we find least-squares fit values of V sin i = 21.8 plus or minus 0.2 km/sec polar T(sub eff) = 9695 plus or minus 25 K, polar log(base 10)g = 3.75 plus or minus 0.02 dex, V(sub eq) = 245 plus or minus 15 km/sec, and inclination 5 deg .1 plus or minus 0 deg .3. The variations in T(sub eff) and log(base 10)g over the photosphere total 390 K and 0.08 dex, respectively. Assuming V sin i = 21.8 km/sec, an independent fit to the observed continuous flux from 1200 to 10,500 A produced a similar set of values with polar T(sub eff) = 9595 plus or minus 20 K, polar log(base 10)g = 3.80 plus or minus 0.03 dex, and inclination 6 deg .0 plus or minus 0 deg .7.

Directional templates for real-time detection of coronal axis rotated faces

NASA Astrophysics Data System (ADS)

Perez, Claudio A.; Estevez, Pablo A.; Garate, Patricio

2004-10-01

Real-time face and iris detection on video images has gained renewed attention because of multiple possible applications in studying eye function, drowsiness detection, virtual keyboard interfaces, face recognition, video processing and multimedia retrieval. In this paper, a study is presented on using directional templates in the detection of faces rotated in the coronal axis. The templates are built by extracting the directional image information from the regions of the eyes, nose and mouth. The face position is determined by computing a line integral using the templates over the face directional image. The line integral reaches a maximum when it coincides with the face position. It is shown an improvement in localization selectivity by the increased value in the line integral computed with the directional template. Besides, improvements in the line integral value for face size and face rotation angle was also found through the computation of the line integral using the directional template. Based on these results the new templates should improve selectivity and hence provide the means to restrict computations to a fewer number of templates and restrict the region of search during the face and eye tracking procedure. The proposed method is real time, completely non invasive and was applied with no background limitation and normal illumination conditions in an indoor environment.

Revised energy levels of singly ionized lanthanum

NASA Astrophysics Data System (ADS)

Güzelçimen, Feyza; Tonka, Mehdi; Uddin, Zaheer; Bhatti, Naveed Anjum; Windholz, Laurentius; Kröger, Sophie; Başar, Gönül

2018-05-01

Based on the experimental wavenumbers of 344 spectral lines from calibrated Fourier transform (FT) spectra as well as wavenumbers of 81 lines from the wavelength tables from literature, the energy of 115 fine structure levels of singly ionized lanthanum has been revised by weighted global fits. The classifications of the lines are provided by numerous previous investigations of lanthanum by different spectroscopic methods and authors. For the high accurate determination of the center of gravity wavenumbers from the experimental spectrum, the hyperfine constants of the involved levels have been taken into account, if possible. For the 94 levels with known hyperfine constants the accuracy of energy values is better than 0.01 cm-1. For 34 levels the magnetic dipole hyperfine constants A have been determined from FT spectra as part of this work. For four of these 34 levels even electric quadrupole hyperfine constants B could be estimated. For levels, which have experimentally unknown hyperfine constants and which are connected only by lines not found in the FT spectra but taken from literature, the uncertainties of energy values are about a factor of 10 higher. A list of all revised level energies together with a compilation of hyperfine structure data is given as well as a list of all lines used.

Evaluating Uncertainties in Coronal Electron Temperature and Radial Speed Measurements Using a Simulation of the Bastille Day Eruption

NASA Astrophysics Data System (ADS)

Reginald, Nelson; St. Cyr, Orville; Davila, Joseph; Rastaetter, Lutz; Török, Tibor

2018-05-01

Obtaining reliable measurements of plasma parameters in the Sun's corona remains an important challenge for solar physics. We previously presented a method for producing maps of electron temperature and speed of the solar corona using K-corona brightness measurements made through four color filters in visible light, which were tested for their accuracies using models of a structured, yet steady corona. In this article we test the same technique using a coronal model of the Bastille Day (14 July 2000) coronal mass ejection, which also contains quiet areas and streamers. We use the coronal electron density, temperature, and flow speed contained in the model to determine two K-coronal brightness ratios at (410.3, 390.0 nm) and (423.3, 398.7 nm) along more than 4000 lines of sight. Now assuming that for real observations, the only information we have for each line of sight are these two K-coronal brightness ratios, we use a spherically symmetric model of the corona that contains no structures to interpret these two ratios for electron temperature and speed. We then compare the interpreted (or measured) values for each line of sight with the true values from the model at the plane of the sky for that same line of sight to determine the magnitude of the errors. We show that the measured values closely match the true values in quiet areas. However, in locations of coronal structures, the measured values are predictably underestimated or overestimated compared to the true values, but can nevertheless be used to determine the positions of the structures with respect to the plane of the sky, in front or behind. Based on our results, we propose that future white-light coronagraphs be equipped to image the corona using four color filters in order to routinely create coronal maps of electron density, temperature, and flow speed.

Complete analysis of ensemble inequivalence in the Blume-Emery-Griffiths model

NASA Astrophysics Data System (ADS)

Hovhannisyan, V. V.; Ananikian, N. S.; Campa, A.; Ruffo, S.

2017-12-01

We study inequivalence of canonical and microcanonical ensembles in the mean-field Blume-Emery-Griffiths model. This generalizes previous results obtained for the Blume-Capel model. The phase diagram strongly depends on the value of the biquadratic exchange interaction K , the additional feature present in the Blume-Emery-Griffiths model. At small values of K , as for the Blume-Capel model, lines of first- and second-order phase transitions between a ferromagnetic and a paramagnetic phase are present, separated by a tricritical point whose location is different in the two ensembles. At higher values of K the phase diagram changes substantially, with the appearance of a triple point in the canonical ensemble, which does not find any correspondence in the microcanonical ensemble. Moreover, one of the first-order lines that starts from the triple point ends in a critical point, whose position in the phase diagram is different in the two ensembles. This line separates two paramagnetic phases characterized by a different value of the quadrupole moment. These features were not previously studied for other models and substantially enrich the landscape of ensemble inequivalence, identifying new aspects that had been discussed in a classification of phase transitions based on singularity theory. Finally, we discuss ergodicity breaking, which is highlighted by the presence of gaps in the accessible values of magnetization at low energies: it also displays new interesting patterns that are not present in the Blume-Capel model.

Inter-laboratory calibration of natural gas round robins for δ2H and δ13C using off-line and on-line techniques

USGS Publications Warehouse

Dai, Jinxing; Xia, Xinyu; Li, Zhisheng; Coleman, Dennis D.; Dias, Robert F.; Gao, Ling; Li, Jian; Deev, Andrei; Li, Jin; Dessort, Daniel; Duclerc, Dominique; Li, Liwu; Liu, Jinzhong; Schloemer, Stefan; Zhang, Wenlong; Ni, Yunyan; Hu, Guoyi; Wang, Xiaobo; Tang, Yongchun

2012-01-01

Compound-specific carbon and hydrogen isotopic compositions of three natural gas round robins were calibrated by ten laboratories carrying out more than 800 measurements including both on-line and off-line methods. Two-point calibrations were performed with international measurement standards for hydrogen isotope ratios (VSMOW and SLAP) and carbon isotope ratios (NBS 19 and L-SVEC CO2). The consensus δ13C values and uncertainties were derived from the Maximum Likelihood Estimation (MLE) based on off-line measurements; the consensus δ2H values and uncertainties were derived from MLE of both off-line and on-line measurements, taking the bias of on-line measurements into account. The calibrated consensus values in ‰ relative to VSMOW and VPDB are: NG1 (coal-related gas): Methane: δ2HVSMOW = − 185.1‰ ± 1.2‰, δ13CVPDB = − 34.18‰ ± 0.10‰ Ethane: δ2HVSMOW = − 156.3‰ ± 1.8‰, δ13CVPDB = − 24.66‰ ± 0.11‰ Propane: δ2HVSMOW = − 143.6‰ ± 3.3‰, δ13CVPDB = − 22.21‰ ± 0.11‰ i-Butane: δ13CVPDB = − 21.62‰ ± 0.12‰ n-Butane: δ13CVPDB = − 21.74‰ ± 0.13‰ CO2: δ13CVPDB = − 5.00‰ ± 0.12‰ NG2 (biogas): Methane: δ2HVSMOW = − 237.0‰ ± 1.2‰, δ13CVPDB = − 68.89‰ ± 0.12‰ NG3 (oil-related gas): Methane: δ2HVSMOW = − 167.6‰ ± 1.0‰, δ13CVPDB = − 43.61‰ ± 0.09‰ Ethane: δ2HVSMOW = − 164.1‰ ± 2.4‰, δ13CVPDB = − 40.24‰ ± 0.10‰ Propane: δ2HVSMOW = − 138.4‰ ± 3.0‰, δ13CVPDB = − 33.79‰ ± 0.09‰ All of the assigned values are traceable to the international carbon isotope standard of VPDB and hydrogen isotope standard of VSMOW.

WE-G-204-06: Grid-Line Artifact Minimization for High Resolution Detectors Using Iterative Residual Scatter Correction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rana, R; Bednarek, D; Rudin, S

2015-06-15

Purpose: Anti-scatter grid-line artifacts are more prominent for high-resolution x-ray detectors since the fraction of a pixel blocked by the grid septa is large. Direct logarithmic subtraction of the artifact pattern is limited by residual scattered radiation and we investigate an iterative method for scatter correction. Methods: A stationary Smit-Rοntgen anti-scatter grid was used with a high resolution Dexela 1207 CMOS X-ray detector (75 µm pixel size) to image an artery block (Nuclear Associates, Model 76-705) placed within a uniform head equivalent phantom as the scattering source. The image of the phantom was divided by a flat-field image obtained withoutmore » scatter but with the grid to eliminate grid-line artifacts. Constant scatter values were subtracted from the phantom image before dividing by the averaged flat-field-with-grid image. The standard deviation of pixel values for a fixed region of the resultant images with different subtracted scatter values provided a measure of the remaining grid-line artifacts. Results: A plot of the standard deviation of image pixel values versus the subtracted scatter value shows that the image structure noise reaches a minimum before going up again as the scatter value is increased. This minimum corresponds to a minimization of the grid-line artifacts as demonstrated in line profile plots obtained through each of the images perpendicular to the grid lines. Artifact-free images of the artery block were obtained with the optimal scatter value obtained by this iterative approach. Conclusion: Residual scatter subtraction can provide improved grid-line artifact elimination when using the flat-field with grid “subtraction” technique. The standard deviation of image pixel values can be used to determine the optimal scatter value to subtract to obtain a minimization of grid line artifacts with high resolution x-ray imaging detectors. This study was supported by NIH Grant R01EB002873 and an equipment grant from Toshiba Medical Systems Corp.« less

Mathematical Analysis for Peristaltic Flow of Two Phase Nanofluid in a Curved Channel

NASA Astrophysics Data System (ADS)

Nadeem, S.; Shahzadi, Iqra

2015-11-01

This paper describes the theoretical analysis for peristaltic motion of water base nanofluid containing distinct types of the nanoparticles like Cu, TiO2, and Al2O3. Equations of nano fluid are modelled and simplified by constructing the suppositions of low Reynolds number as well as long wave length. The reduced equations are solved exactly. Solutions are represented through graphs. Outcomes for the velocity, temperature, pressure rise and stream lines are analyzed graphically. The work presented here is based on the fictitious values, however some other values can be tested experimentally.

Nonlinear mixed effects dose response modeling in high throughput drug screens: application to melanoma cell line analysis.

PubMed

Ding, Kuan-Fu; Petricoin, Emanuel F; Finlay, Darren; Yin, Hongwei; Hendricks, William P D; Sereduk, Chris; Kiefer, Jeffrey; Sekulic, Aleksandar; LoRusso, Patricia M; Vuori, Kristiina; Trent, Jeffrey M; Schork, Nicholas J

2018-01-12

Cancer cell lines are often used in high throughput drug screens (HTS) to explore the relationship between cell line characteristics and responsiveness to different therapies. Many current analysis methods infer relationships by focusing on one aspect of cell line drug-specific dose-response curves (DRCs), the concentration causing 50% inhibition of a phenotypic endpoint (IC 50 ). Such methods may overlook DRC features and do not simultaneously leverage information about drug response patterns across cell lines, potentially increasing false positive and negative rates in drug response associations. We consider the application of two methods, each rooted in nonlinear mixed effects (NLME) models, that test the relationship relationships between estimated cell line DRCs and factors that might mitigate response. Both methods leverage estimation and testing techniques that consider the simultaneous analysis of different cell lines to draw inferences about any one cell line. One of the methods is designed to provide an omnibus test of the differences between cell line DRCs that is not focused on any one aspect of the DRC (such as the IC 50 value). We simulated different settings and compared the different methods on the simulated data. We also compared the proposed methods against traditional IC 50 -based methods using 40 melanoma cell lines whose transcriptomes, proteomes, and, importantly, BRAF and related mutation profiles were available. Ultimately, we find that the NLME-based methods are more robust, powerful and, for the omnibus test, more flexible, than traditional methods. Their application to the melanoma cell lines reveals insights into factors that may be clinically useful.

Voltage gain optimization of transmission line transformers

NASA Astrophysics Data System (ADS)

Pécastaing, L.; Reess, T.; Paillol, J.; Gibert, A.; Domens, P.

2003-06-01

Transmission Line Transformers (TLT) based on the use of ferrite beads are presented. This work aims at optimising the performance of the voltage gain and the compactness of the TLT according to the position, the type and the number of ferrites used. The ferrites have been selected taking into account two main parameters: the maximum currents flowing through the outer conductor of the lines of a TLT without ferrite beads and the current frequencies. The function of these ferrites is to decrease the effect of parasitic short-circuit transmission lines between the outer conductors of the coaxial cables of the TLT. Voltages and secondary currents are measured on each cable. The voltage gain achieved reaches the optimum theoretical value thanks to the use of ferrites for a 2, 4 and 10-stage transmission line transformer. Each cable is shorter than 1.5 meter in length which provides an unquestionable advantage of compactness.

Multiple groups of orientation-selective visual mechanisms underlying rapid orientated-line detection.

PubMed Central

Foster, D H; Westland, S

1998-01-01

Visual search for an edge or line element differing in orientation from a background of other edge or line elements can be performed rapidly and effortlessly. In this study, based on psychophysical measurements with ten human observers, threshold values of the angle between a target and background line elements were obtained as functions of background-element orientation, in brief masked displays. A repeated-loess analysis of the threshold functions suggested the existence of several groups of orientation-selective mechanisms contributing to rapid orientated-line detection; specifically, coarse, intermediate and fine mechanisms with preferred orientations spaced at angles of approximately 90 degrees, 35 degrees, and 10 degrees-25 degrees, respectively. The preferred orientations of coarse and some intermediate mechanisms coincided with the vertical or horizontal of the frontoparallel plane, but the preferred orientations of fine mechanisms varied randomly from observer to observer, possibly reflecting individual variations in neuronal sampling characteristics. PMID:9753784

Improved Laboratory Values of the H{sub 2} Lyman and Werner Lines for Constraining Time Variation of the Proton-to-Electron Mass Ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salumbides, E. J.; Khramov, A.; Wolf, A. L.

2008-11-28

Two distinct high-accuracy laboratory spectroscopic investigations of the H{sub 2} molecule are reported. Anchor lines in the EF{sup 1}{sigma}{sub g}{sup +}-X{sup 1}{sigma}{sub g}{sup +} system are calibrated by two-photon deep-UV Doppler-free spectroscopy, while independent Fourier-transform spectroscopic measurements are performed that yield accurate spacings in the B{sup 1}{sigma}{sub u}{sup +}-EF{sup 1}{sigma}{sub g}{sup +} and I{sup 1}{pi}{sub g}-C{sup 1}{pi}{sub u} systems. From combination differences accurate transition wavelengths for the B-X Lyman and the C-X Werner lines can be determined with accuracies better than {approx}5x10{sup -9}, representing a major improvement over existing values. This metrology provides a practically exact database to extract amore » possible variation of the proton-to-electron mass ratio based on H{sub 2} lines in high-redshift objects. Moreover, it forms a rationale for equipping a future class of telescopes, carrying 30-40 m dishes, with novel spectrometers of higher resolving powers.« less

Model training across multiple breeding cycles significantly improves genomic prediction accuracy in rye (Secale cereale L.).

PubMed

Auinger, Hans-Jürgen; Schönleben, Manfred; Lehermeier, Christina; Schmidt, Malthe; Korzun, Viktor; Geiger, Hartwig H; Piepho, Hans-Peter; Gordillo, Andres; Wilde, Peer; Bauer, Eva; Schön, Chris-Carolin

2016-11-01

Genomic prediction accuracy can be significantly increased by model calibration across multiple breeding cycles as long as selection cycles are connected by common ancestors. In hybrid rye breeding, application of genome-based prediction is expected to increase selection gain because of long selection cycles in population improvement and development of hybrid components. Essentially two prediction scenarios arise: (1) prediction of the genetic value of lines from the same breeding cycle in which model training is performed and (2) prediction of lines from subsequent cycles. It is the latter from which a reduction in cycle length and consequently the strongest impact on selection gain is expected. We empirically investigated genome-based prediction of grain yield, plant height and thousand kernel weight within and across four selection cycles of a hybrid rye breeding program. Prediction performance was assessed using genomic and pedigree-based best linear unbiased prediction (GBLUP and PBLUP). A total of 1040 S 2 lines were genotyped with 16 k SNPs and each year testcrosses of 260 S 2 lines were phenotyped in seven or eight locations. The performance gap between GBLUP and PBLUP increased significantly for all traits when model calibration was performed on aggregated data from several cycles. Prediction accuracies obtained from cross-validation were in the order of 0.70 for all traits when data from all cycles (N CS  = 832) were used for model training and exceeded within-cycle accuracies in all cases. As long as selection cycles are connected by a sufficient number of common ancestors and prediction accuracy has not reached a plateau when increasing sample size, aggregating data from several preceding cycles is recommended for predicting genetic values in subsequent cycles despite decreasing relatedness over time.

Optimized tuner selection for engine performance estimation

NASA Technical Reports Server (NTRS)

Simon, Donald L. (Inventor); Garg, Sanjay (Inventor)

2013-01-01

A methodology for minimizing the error in on-line Kalman filter-based aircraft engine performance estimation applications is presented. This technique specifically addresses the underdetermined estimation problem, where there are more unknown parameters than available sensor measurements. A systematic approach is applied to produce a model tuning parameter vector of appropriate dimension to enable estimation by a Kalman filter, while minimizing the estimation error in the parameters of interest. Tuning parameter selection is performed using a multi-variable iterative search routine which seeks to minimize the theoretical mean-squared estimation error. Theoretical Kalman filter estimation error bias and variance values are derived at steady-state operating conditions, and the tuner selection routine is applied to minimize these values. The new methodology yields an improvement in on-line engine performance estimation accuracy.

A coastal hazards data base for the U.S. West Coast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gornitz, V.M.; Beaty, T.W.; Daniels, R.C.

1997-12-01

This document describes the contents of a digital data base that may be used to identify coastlines along the US West Coast that are at risk to sea-level rise. This data base integrates point, line, and polygon data for the US West Coast into 0.25{degree} latitude by 0.25{degree} longitude grid cells and into 1:2,000,000 digitized line segments that can be used by raster or vector geographic information systems (GIS) as well as by non-GIS data bases. Each coastal grid cell and line segment contains data variables from the following seven data sets: elevation, geology, geomorphology, sea-level trends, shoreline displacement (erosion/accretion),more » tidal ranges, and wave heights. One variable from each data set was classified according to its susceptibility to sea-level rise and/or erosion to form 7 relative risk variables. These risk variables range in value from 1 to 5 and may be used to calculate a Coastal Vulnerability Index (CVI). Algorithms used to calculate several CVIs are listed within this text.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Fan W.; Contescu, Cristian I.; Gallego, Nidia C.

Laser ultrasonic line source methods have been used to study elastic anisotropy in nuclear graphites by measuring shear wave birefringence. Depending on the manufacturing processes used during production, nuclear graphites can exhibit various degrees of material anisotropy related to preferred crystallite orientation and to microcracking. In this paper, laser ultrasonic line source measurements of shear wave birefringence on NBG-25 have been performed to assess elastic anisotropy. Laser line sources allow specific polarizations for shear waves to be transmitted – the corresponding wavespeeds can be used to compute bulk, elastic moduli that serve to quantify anisotropy. These modulus values can bemore » interpreted using physical property models based on orientation distribution coefficients and microcrack-modified, single crystal moduli to represent the combined effects of crystallite orientation and microcracking on material anisotropy. Finally, ultrasonic results are compared to and contrasted with measurements of anisotropy based on the coefficient of thermal expansion to show the relationship of results from these techniques.« less

Thiazole-based nitrogen mustards: Design, synthesis, spectroscopic studies, DFT calculation, molecular docking, and antiproliferative activity against selected human cancer cell lines

NASA Astrophysics Data System (ADS)

Łączkowski, Krzysztof Z.; Świtalska, Marta; Baranowska-Łączkowska, Angelika; Plech, Tomasz; Paneth, Agata; Misiura, Konrad; Wietrzyk, Joanna; Czaplińska, Barbara; Mrozek-Wilczkiewicz, Anna; Malarz, Katarzyna; Musioł, Robert; Grela, Izabela

2016-09-01

Synthesis, characterization and investigation of antiproliferative activity of ten thiazole-based nitrogen mustard against human cancer cells lines (MV4-11, A549, MCF-7 and HCT116) and normal mouse fibroblast (BALB/3T3) is presented. The structures of novel compounds were determined using 1H and 13C NMR, FAB(+)-MS, and elemental analyses. Among the derivatives, 5b, 5c, 5e, 5f and 5i were found to exhibit high activity against human leukaemia MV4-11 cells with IC50 values of 2.17-4.26 μg/ml. The cytotoxic activity of compound 5c and 5f against BALB/3T3 cells is up to 20 times lower than against cancer cell lines. Our results also show that compounds 5e and 5i have very strong activity against MCF-7 and HCT116 with IC50 values of 3.02-4.13 μg/ml. Moreover, spectroscopic characterization and cellular localization for selected compound were performed. In order to identify potential drug targets we perform computer simulations with DNA-binding site of hTopoI and hTopoII and quantum chemical calculation of interaction and binding energies in complexes of the five most active compounds with guanine.

Using Practice-Based Evidence to Improve Supportive Care Practices to Reduce Central Line-Associated Bloodstream Infections in a Pediatric Oncology Unit [Formula: see text].

PubMed

Linder, Lauri A; Gerdy, Cheryl; Abouzelof, Rouett; Wilson, Andrew

Children with cancer are a subset of patients with central lines with distinct risk factors for infection including periods of prolonged neutropenia and compromised mucous membrane integrity. This article relates the implementation of principles of practice-based evidence to identify interventions in addition to best practice maintenance care bundles to reduce central line-associated bloodstream infections involving viridans group streptococci and coagulase-negative staphylococci on an inpatient pediatric oncology unit. Review of individual events combined with review of current clinical practice guided the development of structured protocols emphasizing routine oral care and general supportive cares. Key principles of the protocols emphasized a 1-2-3 mnemonic and included daily bathing, twice daily oral care, and out-of-bed activity 3 times daily. Poisson regression identified a significant main effect for time period for central line-associated bloodstream infection rates involving both viridans group streptococci and coagulase-negative staphylococci. Significant differences were present between the preintervention baseline and implementation of the supportive care protocols. Project outcomes demonstrate the added value of using principles of practice-based evidence to guide the development of interventions to improve clinical care when evidence-based sources are limited.

Understanding how orthopaedic surgery practices generate value for healthcare systems.

PubMed

Olson, Steven A; Mather, Richard C

2013-06-01

Orthopaedic surgery practices can provide substantial value to healthcare systems. Increasingly, healthcare administrators are speaking of the need for alignment between physicians and healthcare systems. However, physicians often do not understand what healthcare administrators value and therefore have difficulty articulating the value they create in discussions with their hospital or healthcare organization. Many health systems and hospitals use service lines as an organizational structure to track the relevant data and manage the resources associated with a particular type of care, such as musculoskeletal care. Understanding service lines and their management can be useful for orthopaedic surgeons interested in interacting with their hospital systems. We provide an overview of two basic types of value orthopaedic surgeons create for healthcare systems: financial or volume-driven benefits and nonfinancial quality or value-driven patient care benefits. We performed a search of PubMed from 1965 to 2012 using the term "service line." Of the 351 citations identified, 18 citations specifically involved the use of service lines to improve patient care in both nursing and medical journals. A service line is a structure used in healthcare organizations to enable management of a subset of activities or resources in a focused area of patient care delivery. There is not a consistent definition of what resources are managed within a service line from hospital to hospital. Physicians can positively impact patient care through engaging in service line management. There is increasing pressure for healthcare systems and hospitals to partner with orthopaedic surgeons. The peer-reviewed literature demonstrates there are limited resources for physicians to understand the value they create when attempting to negotiate with their hospital or healthcare organization. To effectively negotiate for resources to provide the best care for patients, orthopaedic surgeons need to claim and demonstrate the value they create in healthcare organizations.

Line Segmentation of 2d Laser Scanner Point Clouds for Indoor Slam Based on a Range of Residuals

NASA Astrophysics Data System (ADS)

Peter, M.; Jafri, S. R. U. N.; Vosselman, G.

2017-09-01

Indoor mobile laser scanning (IMLS) based on the Simultaneous Localization and Mapping (SLAM) principle proves to be the preferred method to acquire data of indoor environments at a large scale. In previous work, we proposed a backpack IMLS system containing three 2D laser scanners and an according SLAM approach. The feature-based SLAM approach solves all six degrees of freedom simultaneously and builds on the association of lines to planes. Because of the iterative character of the SLAM process, the quality and reliability of the segmentation of linear segments in the scanlines plays a crucial role in the quality of the derived poses and consequently the point clouds. The orientations of the lines resulting from the segmentation can be influenced negatively by narrow objects which are nearly coplanar with walls (like e.g. doors) which will cause the line to be tilted if those objects are not detected as separate segments. State-of-the-art methods from the robotics domain like Iterative End Point Fit and Line Tracking were found to not handle such situations well. Thus, we describe a novel segmentation method based on the comparison of a range of residuals to a range of thresholds. For the definition of the thresholds we employ the fact that the expected value for the average of residuals of n points with respect to the line is σ / √n. Our method, as shown by the experiments and the comparison to other methods, is able to deliver more accurate results than the two approaches it was tested against.

Understanding Local Policy Elites' Perceptions on the Benefits and Risks Associated with High-Voltage Power Line Installations in the State of Arkansas.

PubMed

Moyer, Rachael M; Song, Geoboo

2016-10-01

Recently, a controversial policy debate has arisen concerning the installation of high-voltage power lines in northwest Arkansas. While proponents argue that such an installation is inevitable to efficiently and reliably support the identified electric load in the region, opponents claim that the lines will degrade the natural environment and hamper the tourism-based local economy in affected regions, notably in Ozark Mountain areas. Of particular interest is to understand how local policy elites perceive the benefits and risks associated with such divisive proposals, which is critical for comprehending the formation and changes of related government policies. Based upon the dual process theory of judgment, this study systematically investigates the triadic relationships between (a) more profound personal value predispositions, (b) affects and feelings, and (c) perceived benefits and risks related to the proposed installation of high-voltage power lines among local policy elites in the state of Arkansas. In doing so, we analyze original data collected from a statewide Internet survey of 420 local leaders and key policymakers about their opinions on the related issues, while considering other factors claimed by previous literature to influence risk perceptions, including trust, knowledge level, and demographic characteristics. Analytical results suggest that grid-group cultural predispositions, as deeply held core values within local policy elites' individual belief systems, both directly and indirectly-through affective feelings-shape perceived utility associated with the installation of high-voltage power lines. We conclude this article by suggesting some practical considerations for better designing policy addressing controversial issues of this nature. © 2016 Society for Risk Analysis.

Postflight analysis of the EVCS-LM communications link for the Apollo 15 mission

NASA Technical Reports Server (NTRS)

Royston, C. L., Jr.; Eggers, D. S.

1972-01-01

Data from the Apollo 15 mission were used to compare the actual performance of the EVCS to LM communications link with the preflight performance predictions. Based on the results of the analysis, the following conclusions were made: (1) The radio transmission loss data show good correlation with predictions during periods when the radio line of sight was obscured. (2) The technique of predicting shadow losses due to obstacles in the radio line of sight provides a good estimate of the actual shadowing loss. (3) When the transmitter was on an upslope, the radio transmission loss approached the free space loss values as the line of sight to the LM was regained.

Fred Hutchinson Cancer Research Center (FHCRC1): Functional Landscape of the Human Kinome in MYCN Amplified and Non-amplified Neuroblastoma | Office of Cancer Genomics

Cancer.gov

In order to identify candidate drugs targets that exhibit lethality only in the context of MYCN amplification, we carried out a set of siRNA screens focused on the kinome, targeting ~713 kinases, utilizing human neuroblastoma cells lines with or without MYCN amplification. The neuroblastoma cell lines were: SK-N-BE2 (MYCN amplified) and SK-N-AS (non-amplified).  The kinase Hits for the MYCN amplified cell line were selected using a combination of their differential activity when compared to the non-MYCN amplified cells and also ranked by P-values, based on the replicates.

Fred Hutchinson Cancer Research Center (FHCRC-1): Functional Landscape of the Human Kinome in MYCN Amplified and Non-amplified Neuroblastoma | Office of Cancer Genomics

Cancer.gov

In order to identify candidate drugs targets that exhibit lethality only in the context of MYCN amplification, we carried out a set of siRNA screens focused on the kinome, targeting ~713 kinases, utilizing human neuroblastoma cells lines with or without MYCN amplification. The neuroblastoma cell lines were: SK-N-BE2 (MYCN amplified) and SK-N-AS (non-amplified). The kinase Hits for the MYCN amplified cell line were selected using a combination of their differential activity when compared to the non-MYCN amplified cells and also ranked by P-values, based on the replicates.

Constraining possible variations of the fine structure constant in strong gravitational fields with the Kα iron line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bambi, Cosimo, E-mail: bambi@fudan.edu.cn

2014-03-01

In extensions of general relativity and in theories aiming at unifying gravity with the forces of the Standard Model, the value of the ''fundamental constants'' is often determined by the vacuum expectation value of new fields, which may thus change in different backgrounds. Variations of fundamental constants with respect to the values measured today in laboratories on Earth are expected to be more evident on cosmological timescales and/or in strong gravitational fields. In this paper, I show that the analysis of the Kα iron line observed in the X-ray spectrum of black holes can potentially be used to probe themore » fine structure constant α in gravitational potentials relative to Earth of Δφ ≈ 0.1. At present, systematic effects not fully under control prevent to get robust and stringent bounds on possible variations of the value of α with this technique, but the fact that current data can be fitted with models based on standard physics already rules out variations of the fine structure constant larger than some percent.« less

The ratio of deuterium to hydrogen in interstellar space. IV - The lines of sight to Delta, Epsilon, and Iota Orionis

NASA Technical Reports Server (NTRS)

Laurent, C.; Vidal-Madjar, A.; York, D. G.

1979-01-01

Deuterium absorption features in spectra of Delta, Epsilon, and Iota Ori obtained with Copernicus are analyzed. The Iota Ori line-of-sight analysis, which is quite detailed because of the high-velocity H I components superposed on the deuterium features, gives a D/H ratio (which is uncertain because of a complex profile) of 0.000014. A D/H ratio of the order of 7 millionths is determined for Delta and Epsilon Ori. For the complex line profiles involved, one may regard this as a formal lower limit. Several attempts were made to increase the ratio N(D I)/N(H I) in the context of reasonable models for the line of sight, but with no success; the derived values are therefore regarded as actual values, not lower limits. Since the derived value is an average on the line of sight, the possibility cannot be ruled out that the true ratios N(D I)/N(H I) in individual nearby components differ from the mean values. The mean value for these two directions is lower by a factor of 4 than the best value for the Zeta Pup line of sight (the highest yet derived for path lengths greater than 50 pc).

A novel on-line spatial-temporal k-anonymity method for location privacy protection from sequence rules-based inference attacks.

PubMed

Zhang, Haitao; Wu, Chenxue; Chen, Zewei; Liu, Zhao; Zhu, Yunhong

2017-01-01

Analyzing large-scale spatial-temporal k-anonymity datasets recorded in location-based service (LBS) application servers can benefit some LBS applications. However, such analyses can allow adversaries to make inference attacks that cannot be handled by spatial-temporal k-anonymity methods or other methods for protecting sensitive knowledge. In response to this challenge, first we defined a destination location prediction attack model based on privacy-sensitive sequence rules mined from large scale anonymity datasets. Then we proposed a novel on-line spatial-temporal k-anonymity method that can resist such inference attacks. Our anti-attack technique generates new anonymity datasets with awareness of privacy-sensitive sequence rules. The new datasets extend the original sequence database of anonymity datasets to hide the privacy-sensitive rules progressively. The process includes two phases: off-line analysis and on-line application. In the off-line phase, sequence rules are mined from an original sequence database of anonymity datasets, and privacy-sensitive sequence rules are developed by correlating privacy-sensitive spatial regions with spatial grid cells among the sequence rules. In the on-line phase, new anonymity datasets are generated upon LBS requests by adopting specific generalization and avoidance principles to hide the privacy-sensitive sequence rules progressively from the extended sequence anonymity datasets database. We conducted extensive experiments to test the performance of the proposed method, and to explore the influence of the parameter K value. The results demonstrated that our proposed approach is faster and more effective for hiding privacy-sensitive sequence rules in terms of hiding sensitive rules ratios to eliminate inference attacks. Our method also had fewer side effects in terms of generating new sensitive rules ratios than the traditional spatial-temporal k-anonymity method, and had basically the same side effects in terms of non-sensitive rules variation ratios with the traditional spatial-temporal k-anonymity method. Furthermore, we also found the performance variation tendency from the parameter K value, which can help achieve the goal of hiding the maximum number of original sensitive rules while generating a minimum of new sensitive rules and affecting a minimum number of non-sensitive rules.

A novel on-line spatial-temporal k-anonymity method for location privacy protection from sequence rules-based inference attacks

PubMed Central

Wu, Chenxue; Liu, Zhao; Zhu, Yunhong

2017-01-01

Analyzing large-scale spatial-temporal k-anonymity datasets recorded in location-based service (LBS) application servers can benefit some LBS applications. However, such analyses can allow adversaries to make inference attacks that cannot be handled by spatial-temporal k-anonymity methods or other methods for protecting sensitive knowledge. In response to this challenge, first we defined a destination location prediction attack model based on privacy-sensitive sequence rules mined from large scale anonymity datasets. Then we proposed a novel on-line spatial-temporal k-anonymity method that can resist such inference attacks. Our anti-attack technique generates new anonymity datasets with awareness of privacy-sensitive sequence rules. The new datasets extend the original sequence database of anonymity datasets to hide the privacy-sensitive rules progressively. The process includes two phases: off-line analysis and on-line application. In the off-line phase, sequence rules are mined from an original sequence database of anonymity datasets, and privacy-sensitive sequence rules are developed by correlating privacy-sensitive spatial regions with spatial grid cells among the sequence rules. In the on-line phase, new anonymity datasets are generated upon LBS requests by adopting specific generalization and avoidance principles to hide the privacy-sensitive sequence rules progressively from the extended sequence anonymity datasets database. We conducted extensive experiments to test the performance of the proposed method, and to explore the influence of the parameter K value. The results demonstrated that our proposed approach is faster and more effective for hiding privacy-sensitive sequence rules in terms of hiding sensitive rules ratios to eliminate inference attacks. Our method also had fewer side effects in terms of generating new sensitive rules ratios than the traditional spatial-temporal k-anonymity method, and had basically the same side effects in terms of non-sensitive rules variation ratios with the traditional spatial-temporal k-anonymity method. Furthermore, we also found the performance variation tendency from the parameter K value, which can help achieve the goal of hiding the maximum number of original sensitive rules while generating a minimum of new sensitive rules and affecting a minimum number of non-sensitive rules. PMID:28767687

Exploring the total Galactic extinction with SDSS BHB stars

NASA Astrophysics Data System (ADS)

Tian, Hai-Jun; Liu, Chao; Hu, Jing-Yao; Xu, Yang; Chen, Xue-Lei

2014-01-01

Aims: We used 12 530 photometrically-selected blue horizontal branch (BHB) stars from the Sloan Digital Sky Survey (SDSS) to estimate the total extinction of the Milky Way at the high Galactic latitudes, RV and AV in each line of sight. Methods: A Bayesian method was developed to estimate the reddening values in the given lines of sight. Based on the most likely values of reddening in multiple colors, we were able to derive the values of RV and AV. Results: We selected 94 zero-reddened BHB stars from seven globular clusters as the template. The reddening in the four SDSS colors for the northern Galactic cap were estimated by comparing the field BHB stars with the template stars. The accuracy of this estimation is around 0.01 mag for most lines of sight. We also obtained ⟨ RV ⟩ to be around 2.40 ± 1.05 and AV map within an uncertainty of 0.1 mag. The results, including reddening values in the four SDSS colors, AV, and RV in each line of sight, are released on line. In this work, we employ an up-to-date parallel technique on GPU card to overcome time-consuming computations. We plan to release online the C++ CUDA code used for this analysis. Conclusions: The extinction map derived from BHB stars is highly consistent with that from Schlegel et al. (1998, ApJ, 500, 525). The derived RV is around 2.40 ± 1.05. The contamination probably makes the RV be larger. Tables 1-4 (excerpt) are available in electronic form at http://www.aanda.orgFull Table 4 is only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/561/A142

Combined line-of-sight error and angular position to generate feedforward control for a charge-coupled device-based tracking loop

NASA Astrophysics Data System (ADS)

Tang, Tao; Cai, Huaxiang; Huang, Yongmei; Ren, Ge

2015-10-01

A feedforward control based on data fusion is proposed to enhance closed-loop performance. The target trajectory as the observed value of a Kalman filter is recovered by synthesizing line-of-sight error and angular position from the encoder. A Kalman filter based on a Singer acceleration model is employed to estimate the target velocity. In this control scheme, the control stability is influenced by the bandwidth of the Kalman filter and time misalignment. The transfer function of the Kalman filter in the frequency domain is built for analyzing the closed loop stability, which shows that the Kalman filter is the major factor that affects the control stability. The feedforward control proposed here is verified through simulations and experiments.

VizieR Online Data Catalog: Blazars equivalent widths and radio luminosity (Landt+, 2004)

NASA Astrophysics Data System (ADS)

Landt, H.; Padovani, P.; Perlman, E. S.; Giommi, P.

2004-07-01

Blazars are currently separated into BL Lacertae objects (BL Lacs) and flat spectrum radio quasars based on the strength of their emission lines. This is performed rather arbitrarily by defining a diagonal line in the Ca H&K break value-equivalent width plane, following Marcha et al. (1996MNRAS.281..425M). We readdress this problem and put the classification scheme for blazars on firm physical grounds. We study ~100 blazars and radio galaxies from the Deep X-ray Radio Blazar Survey (DXRBS, Cat. and ) and 2-Jy radio survey and find a significant bimodality for the narrow emission line [OIII]{lambda}5007. This suggests the presence of two physically distinct classes of radio-loud active galactic nuclei (AGN). We show that all radio-loud AGN, blazars and radio galaxies, can be effectively separated into weak- and strong-lined sources using the [OIII]{lambda}5007-[OII]{lambda}3727 equivalent width plane. This plane allows one to disentangle orientation effects from intrinsic variations in radio-loud AGN. Based on DXRBS, the strongly beamed sources of the new class of weak-lined radio-loud AGN are made up of BL Lacs at the ~75 per cent level, whereas those of the strong-lined radio-loud AGN include mostly (~97 per cent) quasars. (4 data files).

Neural network method for lossless two-conductor transmission line equations based on the IELM algorithm

NASA Astrophysics Data System (ADS)

Yang, Yunlei; Hou, Muzhou; Luo, Jianshu; Liu, Taohua

2018-06-01

With the increasing demands for vast amounts of data and high-speed signal transmission, the use of multi-conductor transmission lines is becoming more common. The impact of transmission lines on signal transmission is thus a key issue affecting the performance of high-speed digital systems. To solve the problem of lossless two-conductor transmission line equations (LTTLEs), a neural network model and algorithm are explored in this paper. By selecting the product of two triangular basis functions as the activation function of hidden layer neurons, we can guarantee the separation of time, space, and phase orthogonality. By adding the initial condition to the neural network, an improved extreme learning machine (IELM) algorithm for solving the network weight is obtained. This is different to the traditional method for converting the initial condition into the iterative constraint condition. Calculation software for solving the LTTLEs based on the IELM algorithm is developed. Numerical experiments show that the results are consistent with those of the traditional method. The proposed neural network algorithm can find the terminal voltage of the transmission line and also the voltage of any observation point. It is possible to calculate the value at any given point by using the neural network model to solve the transmission line equation.

Apparatus, system and method for providing cryptographic key information with physically unclonable function circuitry

DOEpatents

Areno, Matthew

2015-12-08

Techniques and mechanisms for providing a value from physically unclonable function (PUF) circuitry for a cryptographic operation of a security module. In an embodiment, a cryptographic engine receives a value from PUF circuitry and based on the value, outputs a result of a cryptographic operation to a bus of the security module. The bus couples the cryptographic engine to control logic or interface logic of the security module. In another embodiment, the value is provided to the cryptographic engine from the PUF circuitry via a signal line which is distinct from the bus, where any exchange of the value by either of the cryptographic engine and the PUF circuitry is for communication of the first value independent of the bus.

Acute physiological responses to recreational in-line skating in young adults.

PubMed

Orepic, Paula; Mikulic, Pavle; Soric, Maroje; Ruzic, Lana; Markovic, Goran

2014-01-01

We examined the physiological responses to in-line skating exercise at self-selected paces in recreationally trained adults. Seven men and 10 women performed in-line skating exercise during which oxygen uptake (VO2) and heart rate (HR) were recorded continuously. Ratings of perceived exertion (RPE) and blood lactate concentration were also obtained at the end of exercise. Furthermore, subjects' peak VO2, peak HR, RPE and gas-exchange thresholds were determined in laboratory settings. The average exercise intensity during in-line skating was 90% of peak HR, 67% of peak VO2, 84% of HR reserve and 64% of VO2 reserve. When expressed as RPE and as metabolic equivalents (METs), the average exercise intensity was 13.1 RPE and 9.4 METs. Overall, these indicators of exercise intensity categorise in-line skating at self-selected paces as a vigorous physical activity. Notably, at similar VO2 values, significantly higher HR (174 ± 16 vs. 156 ± 6 bpm; p<0.001) and RPE (13.1 ± 1.4 vs. 11.7 ± 1.4; p=0.019) were observed for in-line skating compared with treadmill running. We conclude that 1. recreational in-line skating induces physiological responses that are sufficient for improving and maintaining cardiovascular fitness in healthy adults, 2. HR- and RPE-based methods for quantifying the exercise intensity during in-line skating may overestimate the actual metabolic load and 3. the derivation of exercise prescriptions for in-line skating should be preferably based on specific (i.e. in-line skating) graded exhaustive exercise test.

Contamination of apple orchard soils and fruit trees with copper-based fungicides: sampling aspects.

PubMed

Wang, Quanying; Liu, Jingshuang; Liu, Qiang

2015-01-01

Accumulations of copper in orchard soils and fruit trees due to the application of Cu-based fungicides have become research hotspots. However, information about the sampling strategies, which can affect the accuracy of the following research results, is lacking. This study aimed to determine some sampling considerations when Cu accumulations in the soils and fruit trees of apple orchards are studied. The study was conducted in three apple orchards from different sites. Each orchard included two different histories of Cu-based fungicides usage, varying from 3 to 28 years. Soil samples were collected from different locations varying with the distances from tree trunk to the canopy drip line. Fruits and leaves from the middle heights of tree canopy at two locations (outer canopy and inner canopy) were collected. The variation in total soil Cu concentrations between orchards was much greater than the variation within orchards. Total soil Cu concentrations had a tendency to increase with the increasing history of Cu-based fungicides usage. Moreover, total soil Cu concentrations had the lowest values at the canopy drip line, while the highest values were found at the half distances between the trunk and the canopy drip line. Additionally, Cu concentrations of leaves and fruits from the outer parts of the canopy were significantly higher than from the inner parts. Depending on the findings of this study, not only the between-orchard variation but also the within-orchard variation should be taken into consideration when conducting future soil and tree samplings in apple orchards.

N III Bowen Lines and Fluorescence Mechanism in the Symbiotic Star AG Peg

NASA Astrophysics Data System (ADS)

Hyung, Siek; Lee, Seong-Jae; Lee, Kang Hwan

2018-03-01

We have investigated the intensities and full width at half maximum (FWHM) of the high dispersion spectroscopic N III emission lines of AG Peg, observed with the Hamilton Echelle Spectrograph (HES) in three different epochs at Mt. Hamilton's Lick Observatory. The earlier theoretical Bowen line study assumed the continuum fluorescence effect, presenting a large discrepancy with the present data. Hence, we analyzed the observed N III lines assuming line fluorescence as the only suitable source: (1) The O III and N III resonance line profiles near λ 374 were decomposed, using the Gaussian function, and the contributions from various O III line components were determined. (2) Based on the theoretical resonant N III intensities, the expected N III Bowen intensities were obtained to fit the observed values. Our study shows that the incoming line photon number ratio must be considered to balance at each N III Bowen line level in the ultraviolet radiation according to the observed lines in the optical zone. We also found that the average FWHM of the N III Bowen lines was about 5 km·s-1 greater than that of the O III Bowen lines, perhaps due to the inherently different kinematic characteristics of their emission zones.

Absolute Transition Probabilities of Lines in the Spectra of Astrophysical Atoms, Molecules, and Ions

NASA Technical Reports Server (NTRS)

Parkinson, W. H.; Smith, P. L.; Yoshino, K.

1984-01-01

Progress in the investigation of absolute transition probabilities (A-values or F values) for ultraviolet lines is reported. A radio frequency ion trap was used for measurement of transition probabilities for intersystem lines seen in astronomical spectra. The intersystem line at 2670 A in Al II, which is seen in pre-main sequence stars and symbiotic stars, was studied.

Preoperative evaluation of cochlear implantation through the round window membrane in the facial recess using high-resolution computed tomography.

PubMed

Xie, Li-Hong; Tang, Jie; Miao, Wen-Jie; Tang, Xiang-Long; Li, Heng; Tang, An-Zhou

2018-06-01

We evaluated the risk of cochlear implantation through the round window membrane in the facial recess through a preoperative analysis of the angle between the facial nerve-round window and the cranial midline using high-resolution temporal bone CT. Temporal bone CT films of 176 patients with profound sensorineural hearing loss at our hospital from 2013 to 2015 were reviewed. The preoperative temporal bone CT scans of the patients were retrospectively analysed. The vertical distance (d value) from the leading edge of the facial nerve to the posterior wall of the external auditory canal and the angle (α value) between the line from the leading edge of the facial nerve to the midpoint of the round window membrane and the median sagittal line on the round window membrane plane were measured. Based on intraoperative observation, the round window membrane was divided into complete round window membrane exposure (group A), partial exposure (group B), and unexposed (group C) groups, and statistical analysis was performed. The α value could be effectively measured for all 176 patients (62.60 ± 7.12), and the d value could be effectively measured for 95 cases (5.53 ± 1.00). An analysis of the correlation between the α and d values of these 95 cases found a negative correlation. Of the 176 cases, one-way analysis of variance (ANOVA) showed that the differences among the groups were significant [P = 0.000 (< 0.05)]. The angle (α value) between the line connecting the leading edge of the facial nerve to the midpoint of the round window and the median sagittal line measured in preoperative CT scans was associated with the difficulty of intraoperatively exposing the round window membrane. When the α value was larger than a certain degree, the difficulty of exposing the round window membrane was increased. In such cases, the surgeon should fully expose the round window membrane during surgery, which could result decrease the likelihood of complications.

Study of Sedimentary Outcrop of Semanggol Formation with the Correlation of Geology, Geotechnical and Geophysics Technique

NASA Astrophysics Data System (ADS)

Nordiana, A. N.; Nordiana, M. M.; Jia, Teoh Ying; Hisham, Hazrul; Sulaiman, Nabila; Maslinda, Umi; Taqiuddin, Z. M.; Nur Amalina, M. K. A.; Afiq Saharudin, Muhamad

2017-04-01

The study location was at Bukit Kukus, Kuala Ketil, Kedah, Malaysia where the geological outcrop of this Semanggol Formation comprises of chert, mudstone, and volcanic tuff. The study was conducted using two geophysical methods, which are 2-D Resistivity and Ground Penetrating Radar (GPR). The objectives of the study are to correlate both of the geophysical methods through the value of conductivity and to identify the physical properties of rocks through the value of porosity and permeability. The data acquisition for both methods was conducted on the same line. For 2-D Resistivity method, the length of the line is 60 m with 1.5 m electrode spacing and the array used was Wenner-Schlumberger. For GPR method, the survey line was on top of the resistivity line, and the frequency of the antenna used is 250 MHz. A good correlation exists between both of the GPR signature and contour maps for resistivity from the surfer 10 software with the outcrop feature. Conductivity value from both GPR and Resistivity method was compared and the range value of conductivity obtained from GPR method almost equivalent with Resistivity method based on derivation and calculation for the sedimentary rocks, which are 0.037 to 0.574 miliSiemens per metre (mS/m) for chert and 0.186 to 10.142 miliSiemens per metre (mS/m) for mudstone. Two types of rock samples were taken, and several geotechnical tests were conducted, but only the value of permeability, K and porosity, ɸ of chert can be calculated, which are 1.95E-22 m2 (original condition) and 2.27E-22 m2 (dry condition) and 3 percent respectively as the sample of mudstone was damaged. The parameter of the 2-D resistivity method derived from Archie’s law was used to calculate the porosity, ɸf value using the Formation Factor equation. The range values of porosity, ɸf for chert mostly in the range of 5 to 25 percent, which is 6.26 to 13.36 percent but slightly out of range for mudstone, which is 14.12 to 36.02 percent.

The Relative Biological Effectiveness for Carbon and Oxygen Ion Beams Using the Raster-Scanning Technique in Hepatocellular Carcinoma Cell Lines

PubMed Central

Habermehl, Daniel; Ilicic, Katarina; Dehne, Sarah; Rieken, Stefan; Orschiedt, Lena; Brons, Stephan; Haberer, Thomas; Weber, Klaus-Josef; Debus, Jürgen; Combs, Stephanie E.

2014-01-01

Background Aim of this study was to evaluate the relative biological effectiveness (RBE) of carbon (12C) and oxygen ion (16O)-irradiation applied in the raster-scanning technique at the Heidelberg Ion beam Therapy center (HIT) based on clonogenic survival in hepatocellular carcinoma cell lines compared to photon irradiation. Methods Four human HCC lines Hep3B, PLC, HepG2 and HUH7 were irradiated with photons, 12C and 16O using a customized experimental setting at HIT for in-vitro trials. Cells were irradiated with increasing physical photon single doses of 0, 2, 4 and 6 Gy and heavy ionsingle doses of 0, 0.125, 0.5, 1, 2, 3 Gy (12C and 16O). SOBP-penetration depth and extension was 35 mm +/−4 mm and 36 mm +/−5 mm for carbon ions and oxygen ions respectively. Mean energy level and mean linear energy transfer (LET) were 130 MeV/u and 112 keV/um for 12C, and 154 MeV/u and 146 keV/um for 16O. Clonogenic survival was computated and realtive biological effectiveness (RBE) values were defined. Results For all cell lines and both particle modalities α- and β-values were determined. As expected, α-values were significantly higher for 12C and 16O than for photons, reflecting a steeper decline of the initial slope of the survival curves for high-LET beams. RBE-values were in the range of 2.1–3.3 and 1.9–3.1 for 12C and 16O, respectively. Conclusion Both irradiation with 12C and 16O using the rasterscanning technique leads to an enhanced RBE in HCC cell lines. No relevant differences between achieved RBE-values for 12C and 16O were found. Results of this work will further influence biological-adapted treatment planning for HCC patients that will undergo particle therapy with 12C or 16O. PMID:25460352

A New Black Hole Mass Estimate for Obscured Active Galactic Nuclei

NASA Astrophysics Data System (ADS)

Minezaki, Takeo; Matsushita, Kyoko

2015-04-01

We propose a new method for estimating the mass of a supermassive black hole, applicable to obscured active galactic nuclei (AGNs). This method estimates the black hole mass using the width of the narrow core of the neutral FeKα emission line in X-rays and the distance of its emitting region from the black hole based on the isotropic luminosity indicator via the luminosity scaling relation. Assuming the virial relation between the locations and the velocity widths of the neutral FeKα line core and the broad Hβ emission line, the luminosity scaling relation of the neutral FeKα line core emitting region is estimated. We find that the velocity width of the neutral FeKα line core falls between that of the broad Balmer emission lines and the corresponding value at the dust reverberation radius for most of the target AGNs. The black hole mass {{M}BH,FeKα } estimated with this method is then compared with other black hole mass estimates, such as the broad emission-line reverberation mass {{M}BH,rev} for type 1 AGNs, the mass {{M}BH,{{H2}O}} based on the H2O maser, and the single-epoch mass estimate {{M}BH,pol} based on the polarized broad Balmer lines for type 2 AGNs. We find that {{M}BH,FeKα } is consistent with {{M}BH,rev} and {{M}BH,pol}, and find that {{M}BH,FeKα } correlates well with {{M}BH,{{H2}O}}. These results suggest that {{M}BH,FeKα } is a potential indicator of the black hole mass for obscured AGNs. In contrast, {{M}BH,FeKα } is systematically larger than {{M}BH,{{H2}O}} by about a factor of 5, and the possible origins are discussed.

A Study of Carrier Based Aircraft Readiness Sustainability in the Event of External Air Logistic Support Deprivation

DTIC Science & Technology

1987-06-01

equation for 7R investment has been used in combination with the linear equation for COD/VOD delivery to produce six " iso -readiness" lines. Each iso ...readiness line represents the value of inventory investment and days since last COD/VOD delivery required to maintain a specific level of FMC. The iso ...Truett, D.B., Manaaerial Economics, second edition, South-Western Publish..ng Co., 1984, p. 65. 158 Iso -Readiness Plot o80mna4C Mad" of ?R Ve COO/VOo WO

Prostate tissue characterization/classification in 144 patient population using wavelet and higher order spectra features from transrectal ultrasound images.

PubMed

Pareek, Gyan; Acharya, U Rajendra; Sree, S Vinitha; Swapna, G; Yantri, Ratna; Martis, Roshan Joy; Saba, Luca; Krishnamurthi, Ganapathy; Mallarini, Giorgio; El-Baz, Ayman; Al Ekish, Shadi; Beland, Michael; Suri, Jasjit S

2013-12-01

In this work, we have proposed an on-line computer-aided diagnostic system called "UroImage" that classifies a Transrectal Ultrasound (TRUS) image into cancerous or non-cancerous with the help of non-linear Higher Order Spectra (HOS) features and Discrete Wavelet Transform (DWT) coefficients. The UroImage system consists of an on-line system where five significant features (one DWT-based feature and four HOS-based features) are extracted from the test image. These on-line features are transformed by the classifier parameters obtained using the training dataset to determine the class. We trained and tested six classifiers. The dataset used for evaluation had 144 TRUS images which were split into training and testing sets. Three-fold and ten-fold cross-validation protocols were adopted for training and estimating the accuracy of the classifiers. The ground truth used for training was obtained using the biopsy results. Among the six classifiers, using 10-fold cross-validation technique, Support Vector Machine and Fuzzy Sugeno classifiers presented the best classification accuracy of 97.9% with equally high values for sensitivity, specificity and positive predictive value. Our proposed automated system, which achieved more than 95% values for all the performance measures, can be an adjunct tool to provide an initial diagnosis for the identification of patients with prostate cancer. The technique, however, is limited by the limitations of 2D ultrasound guided biopsy, and we intend to improve our technique by using 3D TRUS images in the future.

Metric Aspects of Digital Images and Digital Image Processing.

DTIC Science & Technology

1984-09-01

produced in a reconstructed digital image. Synthesized aerial photographs were formed by processing a combined elevation and orthophoto data base. These...brightness values h1 and Iion b) a line equation whose two parameters are calculated h12, along with tile borderline that separates the two intensity

49 CFR 1152.34 - Return on investment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION UNDER 49 U.S.C. 10903 Standards for Determining Costs, Revenues, and Return on Value § 1152.34...). (ii) The amount of current income tax benefits resulting from abandonment of the line which would have... income tax liability from abandonment, the liability should be deducted from the investment base.) This...

49 CFR 1152.34 - Return on investment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION UNDER 49 U.S.C. 10903 Standards for Determining Costs, Revenues, and Return on Value § 1152.34...). (ii) The amount of current income tax benefits resulting from abandonment of the line which would have... income tax liability from abandonment, the liability should be deducted from the investment base.) This...

49 CFR 1152.34 - Return on investment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION UNDER 49 U.S.C. 10903 Standards for Determining Costs, Revenues, and Return on Value § 1152.34...). (ii) The amount of current income tax benefits resulting from abandonment of the line which would have... income tax liability from abandonment, the liability should be deducted from the investment base.) This...

The Art and Science of Notebooks

ERIC Educational Resources Information Center

Porter, Keri; Yokoi, Craig; Yee, Bertina

2011-01-01

Along with inquiry-based teaching, exploring the elements of art can guide students to view and represent objects realistically. Understanding line, shape, color, value, form, space, and texture helps bridge the gap between what students actually observe and what their preconceived ideas about the object may be. This type of explicit instruction…

Protecting sediment-sensitive aquatic species inmountain streams through the application of biologically based streambed sediment criteria

EPA Science Inventory

We evaluated several lines of evidence to identify bedded fine sediment levels that should protect and maintain self-sustaining populations of native sediment-sensitive aquatic species in the western US. To identify these potential criterion values for streambed sediments ≤0.06 ...

The predictive value of 53BP1 and BRCA1 mRNA expression in advanced non-small-cell lung cancer patients treated with first-line platinum-based chemotherapy

PubMed Central

Bonanno, Laura; Costa, Carlota; Majem, Margarita; Sanchez, Jose Javier; Gimenez-Capitan, Ana; Rodriguez, Ignacio; Vergenegre, Alain; Massuti, Bartomeu; Favaretto, Adolfo; Rugge, Massimo; Pallares, Cinta; Taron, Miquel; Rosell, Rafael

2013-01-01

Platinum-based chemotherapy is the standard first-line treatment for non-oncogene-addicted non-small cell lung cancers (NSCLCs) and the analysis of multiple DNA repair genes could improve current models for predicting chemosensitivity. We investigated the potential predictive role of components of the 53BP1 pathway in conjunction with BRCA1. The mRNA expression of BRCA1, MDC1, CASPASE3, UBC13, RNF8, 53BP1, PIAS4, UBC9 and MMSET was analyzed by real-time PCR in 115 advanced NSCLC patients treated with first-line platinum-based chemotherapy. Patients expressing low levels of both BRCA1 and 53BP1 obtained a median progression-free survival of 10.3 months and overall survival of 19.3 months, while among those with low BRCA1 and high 53BP1 progression-free survival was 5.9 months (P <0.0001) and overall survival was 8.2 months (P=0.001). The expression of 53BP1 refines BRCA1-based predictive modeling to identify patients most likely to benefit from platinum-based chemotherapy. PMID:24197907

Geodesy and astrometry by transatlantic long base line interferometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cannon, W.H.; Langley, R.B.; Petrachenko, W.T.

1979-01-10

We report geodetic and astrometric results from the analysis of fringe frequency observations from a series of three long base line interferometry (LBI) experiments carried out in 1973 between the 46-m antenna of the Algonquin Radio Observatory, Lake Traverse, Canada, and the 25-m antenna at Chilbolton Field Station, Chilbolton, England. The rms deviation from the mean of the estimates of the length and orientation of the 5251-km equatorial component of the base line from all three experiments is 1.05-m and 0.015'', respectively. The experiments also yielded positions of five extragalactic radio sources. The reported positions, each of which is frommore » only a single experiment, have uncertainties of about 0.2'' in declination (except for low declination sources) and about 0.01 s in right ascension. The LBI determination of the length and orientation of the equatorial component of the base line is compared to the corresponding values derived from Naval Weapons Laboratory 9D (NWL-9D) coorinates for the antennae. The two length measurements agree in scale within quoted experimental errors; however, the NWL-9D coordinate frame is found to be rotated 0.867'' +- 0.1'' to the east relative to the average terrestrial frame of the Bureau Internationale de l'Heure (BIH),(LBI coordinate frame). This is in good agreement with the expected misalignment of 0.65'' +- 0.2''. The differences in the rates of the clocks used at each end of the base line were also determined and compared to Loran-C observations.« less

Microalgal process-monitoring based on high-selectivity spectroscopy tools: status and future perspectives.

PubMed

Podevin, Michael; Fotidis, Ioannis A; Angelidaki, Irini

2018-08-01

Microalgae are well known for their ability to accumulate lipids intracellularly, which can be used for biofuels and mitigate CO 2 emissions. However, due to economic challenges, microalgae bioprocesses have maneuvered towards the simultaneous production of food, feed, fuel, and various high-value chemicals in a biorefinery concept. On-line and in-line monitoring of macromolecules such as lipids, proteins, carbohydrates, and high-value pigments will be more critical to maintain product quality and consistency for downstream processing in a biorefinery to maintain and valorize these markets. The main contribution of this review is to present current and prospective advances of on-line and in-line process analytical technology (PAT), with high-selectivity - the capability of monitoring several analytes simultaneously - in the interest of improving product quality, productivity, and process automation of a microalgal biorefinery. The high-selectivity PAT under consideration are mid-infrared (MIR), near-infrared (NIR), and Raman vibrational spectroscopies. The current review contains a critical assessment of these technologies in the context of recent advances in software and hardware in order to move microalgae production towards process automation through multivariate process control (MVPC) and software sensors trained on "big data". The paper will also include a comprehensive overview of off-line implementations of vibrational spectroscopy in microalgal research as it pertains to spectral interpretation and process automation to aid and motivate development.

Understanding drugs in breast cancer through drug sensitivity screening.

PubMed

Uhr, Katharina; Prager-van der Smissen, Wendy J C; Heine, Anouk A J; Ozturk, Bahar; Smid, Marcel; Göhlmann, Hinrich W H; Jager, Agnes; Foekens, John A; Martens, John W M

2015-01-01

With substantial numbers of breast tumors showing or acquiring treatment resistance, it is of utmost importance to develop new agents for the treatment of the disease, to know their effectiveness against breast cancer and to understand their relationships with other drugs to best assign the right drug to the right patient. To achieve this goal drug screenings on breast cancer cell lines are a promising approach. In this study a large-scale drug screening of 37 compounds was performed on a panel of 42 breast cancer cell lines representing the main breast cancer subtypes. Clustering, correlation and pathway analyses were used for data analysis. We found that compounds with a related mechanism of action had correlated IC50 values and thus grouped together when the cell lines were hierarchically clustered based on IC50 values. In total we found six clusters of drugs of which five consisted of drugs with related mode of action and one cluster with two drugs not previously connected. In total, 25 correlated and four anti-correlated drug sensitivities were revealed of which only one drug, Sirolimus, showed significantly lower IC50 values in the luminal/ERBB2 breast cancer subtype. We found expected interactions but also discovered new relationships between drugs which might have implications for cancer treatment regimens.

Polarization singularity indices in Gaussian laser beams

NASA Astrophysics Data System (ADS)

Freund, Isaac

2002-01-01

Two types of point singularities in the polarization of a paraxial Gaussian laser beam are discussed in detail. V-points, which are vector point singularities where the direction of the electric vector of a linearly polarized field becomes undefined, and C-points, which are elliptic point singularities where the ellipse orientations of elliptically polarized fields become undefined. Conventionally, V-points are characterized by the conserved integer valued Poincaré-Hopf index η, with generic value η=±1, while C-points are characterized by the conserved half-integer singularity index IC, with generic value IC=±1/2. Simple algorithms are given for generating V-points with arbitrary positive or negative integer indices, including zero, at arbitrary locations, and C-points with arbitrary positive or negative half-integer or integer indices, including zero, at arbitrary locations. Algorithms are also given for generating continuous lines of these singularities in the plane, V-lines and C-lines. V-points and C-points may be transformed one into another. A topological index based on directly measurable Stokes parameters is used to discuss this transformation. The evolution under propagation of V-points and C-points initially embedded in the beam waist is studied, as is the evolution of V-dipoles and C-dipoles.

Copernicus ultraviolet observations of mass-loss effects in O and B stars

NASA Technical Reports Server (NTRS)

Snow, T. P., Jr.; Morton, D. C.

1976-01-01

Far-UV spectra of 47 O, B, and A stars obtained with the Copernicus satellite are examined for P Cygni profiles. For all 40 stars with displaced absorption lines, values are given for the velocities of the short-wavelength edge, the line center, and the emission peak (if present). Parts of the spectra of 42 stars are reproduced, evidence for mass motions in ground-based spectra is discussed, and the best available data are summarized on the wavelengths and oscillator strengths of most lines likely to show mass-loss effects in either visual or UV spectra. The main conclusions are that: (1) the far-UV transitions, especially resonance lines, show that mass flow is present over a much wider group of stars than revealed by visible data on subordinate lines; (2) most of the line shifts imply mass motion away from the stars; (3) mass flow occurs in all but one star brighter than a bolometric magnitude of -6.0; and (4) the observed terminal velocities generally exhibit no significant correlation with temperature, luminosity, gravity, rotational velocity, or line strength.

High resolution measurements of solar induced chlorophyll fluorescence in the Fraunhofer oxigen bands

NASA Astrophysics Data System (ADS)

Mazzoni, M.; Agati, G.; Cecchi, G.; Toci, G.; Mazzinghi, P.

2017-11-01

Spectra of solar radiance reflected by leaves close to the Fraunhofer bands show the net contribution of chlorophyll fluorescence emission which adds to the reflected solar spectra. In a laboratory experiment, a low stray light, high resolution, 0.85 m double monochromator was used to filter radiation living leaves still attached to the plant in correspondence of the 687 nm and 760 nm O2 absorption bands. Reference spectra from a non fluorescent white reference were also acquired. Acquisition was performed by a Microchannel plate (MCP) intensified diode array with 512 elements. A fit of the spectral data outside the absorption lines allowed to retrieve the spectral base-line as a function of wavelength for the reference panel and the leaf. Reflectance functions were determined extending the Plascyck equation system to all the resolved lines of the oxygen absorption bands and using the base-lines for the continuum values. Fluorescence was deduced from the same equation system, using both the measured leaf and reference radiance spectra and the leaf reflectance fitting function.

First detection of bromine and antimony in hot stars

NASA Astrophysics Data System (ADS)

Werner, K.; Rauch, T.; Knörzer, M.; Kruk, J. W.

2018-06-01

Bromine (Z = 35) and antimony (Z = 51) are extremely difficult to detect in stars. In very few instances, weak and mostly uncertain identifications of Br I, Br II, and Sb II in relatively cool, chemically peculiar stars were successful. Adopted solar abundance values rely on meteoritic determinations. Here, we announce the first identification of these species in far-ultraviolet spectra of hot stars (with effective temperatures of 49 500-70 000 K), namely in helium-rich (spectral type DO) white dwarfs. We identify the Br VI resonance line at 945.96 Å. A previous claim of Br detection based on this line is incorrect because its wavelength position is inaccurate by about 7 Å in atomic databases. Taking advantage of precise laboratory measurements, we identify this line as well as two other, subordinate Br VI lines. Antimony is detected by the Sb V resonance doublet at 1104.23/1225.98 Å as well as two subordinate Sb VI lines. A model-atmosphere analysis reveals strongly oversolar Br and Sb abundances that are caused by radiative-levitation dominated atomic diffusion. Based on observations made with the NASA-CNES-CSA Far Ultraviolet Spectroscopic Explorer.Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS5-26666.

Children's Responses to Line Spacing in Early Reading Books or "Holes to Tell Which Line You're On"

ERIC Educational Resources Information Center

Reynolds, Linda; Walker, Sue; Duncan, Alison

2006-01-01

This paper describes a study designed to find out whether children's reading would be affected by line spacing that is wider or narrower than the commonly used default values. The realistic, high quality test material was set using a range of four different line spacing values, and twenty-four children in Years 1 and 2 (between five and seven…

Hazardous and Toxic Waste (HTW) Contracting Problems: A Study of the Contracting Problems Related to Surety Bonding in the HTW Cleanup Program

DTIC Science & Technology

1990-07-01

Fair value of solely owned real estate* $ b. All mortgages or other encumbrances on the real estate included in Line a c. Real estate equity (subtract...Line b from Line a) d. Fair value of all solely owned property other than real estate* e. Total of the amounts on Lines c and d f. All other

Analysis of Acoustic Ambient Noise in Monterey Bay, California.

DTIC Science & Technology

1982-12-01

6th line - 1/3-octave band levels, calculated from subroutines " Sub7 ", "Sub8", or "SubS" for center frequencies of 125 Hz (.213). and 25Q H z (.218) for...256 bins. (-191; calculates overall band levels for "corrected plots" based on analyzer scale selected (201); 77 ŕ Subroutines " Sub7 ", "SuhS", and...levels are calculated as positive values to be added to other values in eq. (3). vice negative values that would be subtracted)_ : " Sub7 ": calculates 1

Resident accuracy of joint line palpation using ultrasound verification.

PubMed

Rho, Monica E; Chu, Samuel K; Yang, Aaron; Hameed, Farah; Lin, Cindy Yuchin; Hurh, Peter J

2014-10-01

To determine the accuracy of knee and acromioclavicular (AC) joint line palpation in Physical Medicine and Rehabilitation (PM&R) residents using ultrasound (US) verification. Cohort study. PM&R residency program at an academic institution. Twenty-four PM&R residents participating in a musculoskeletal US course (7 PGY-2, 8 PGY-3, and 9 PGY4 residents). Twenty-four PM&R residents participating in an US course were asked to palpate the AC joint and lateral joint line of the knee in a female and male model before the start of the course. Once the presumed joint line was localized, the residents were asked to tape an 18-gauge, 1.5-inch, blunt-tip needle parallel to the joint line on the overlying skin. The accuracy of needle placement over the joint line was verified using US. US verification of correct needle placement over the joint line. Overall AC joint palpation accuracy was 16.7%, and knee lateral joint line palpation accuracy was 58.3%. Based on the resident level of education, using a value of P < .05, there were no statistically significant differences in the accuracy of joint line palpation. Residents in this study demonstrate poor accuracy of AC joint and lateral knee joint line identification by palpation, using US as the criterion standard for verification. There were no statistically significant differences in the accuracy rates of joint line palpation based on resident level of education. US may be a useful tool to use to advance the current methods of teaching the physical examination in medical education. Copyright © 2014 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

Comparison of Omadacycline and Tigecycline Pharmacokinetics in the Plasma, Epithelial Lining Fluid, and Alveolar Cells of Healthy Adult Subjects.

PubMed

Gotfried, Mark H; Horn, Karolyn; Garrity-Ryan, Lynne; Villano, Stephen; Tzanis, Evan; Chitra, Surya; Manley, Amy; Tanaka, S Ken; Rodvold, Keith A

2017-09-01

The steady-state concentrations of omadacycline and tigecycline in the plasma, epithelial lining fluid (ELF), and alveolar cells (AC) of 58 healthy adult subjects were obtained. Subjects were administered either omadacycline at 100 mg intravenously (i.v.) every 12 h for two doses followed by 100 mg i.v. every 24 h for three doses or tigecycline at an initial dose of 100 mg i.v. followed by 50 mg i.v. every 12 h for six doses. A bronchoscopy and bronchoalveolar lavage were performed once in each subject following the start of the fifth dose of omadacycline at 0.5, 1, 2, 4, 8, 12, or 24 h and after the start of the seventh dose of tigecycline at 2, 4, 6, or 12 h. The value of the area under the concentration-time curve (AUC) from time zero to 24 h postdosing (AUC 0-24 ) (based on mean concentrations) in ELF and the ratio of the ELF to total plasma omadacycline concentration based on AUC 0-24 values were 17.23 mg · h/liter and 1.47, respectively. The AUC 0-24 value in AC was 302.46 mg · h/liter, and the ratio of the AC to total plasma omadacycline concentration was 25.8. In comparison, the values of the AUC from time zero to 12 h postdosing (AUC 0-12 ) based on the mean concentrations of tigecycline in ELF and AC were 3.16 and 38.50 mg · h/liter, respectively. The ratio of the ELF and AC to total plasma concentrations of tigecycline based on AUC 0-12 values were 1.71 and 20.8, respectively. The pharmacokinetic advantages of higher and sustained concentrations of omadacycline compared to those of tigecycline in plasma, ELF, and AC suggest that omadacycline is a promising antibacterial agent for the treatment of lower respiratory tract bacterial infections caused by susceptible pathogens. Copyright © 2017 Gotfried et al.

Ground-based infrared spectroscopic measurements of atmospheric hydrogen cyanide

NASA Technical Reports Server (NTRS)

Rinsland, C. P.; Smith, M. A. H.; Rinsland, P. L.; Goldman, A.; Brault, J. W.; Stokes, G. M.

1982-01-01

A number of lines of the nu-3 band of hydrogen cyanide have been detected in solar absorption spectra recorded near sunrise and sunset at Kitt Peak National Observatory (elevation 2095 m) with a 0.01/cm resolution Fourier transform spectrometer. Analysis of two of the strongest and best isolated lines has led to a value of 2.73 x 10 to the 15th molecules/sq cm for the vertical column abundance of HCN above Kitt Peak. The accuracy of this value is estimated as + or - 25%. This result, combined with the stratospheric concentration of HCN derived by Coffey, Mankin, and Cicerone (1981), yields 166 parts per trillion by volume for the average mixing ratio of HCN between 2 and 12 km. This is the first determination of the HCN concentration in the nonurban troposphere.

Imaging tristimulus colorimeter for the evaluation of color in printed textiles

NASA Astrophysics Data System (ADS)

Hunt, Martin A.; Goddard, James S., Jr.; Hylton, Kathy W.; Karnowski, Thomas P.; Richards, Roger K.; Simpson, Marc L.; Tobin, Kenneth W., Jr.; Treece, Dale A.

1999-03-01

The high-speed production of textiles with complicated printed patterns presents a difficult problem for a colorimetric measurement system. Accurate assessment of product quality requires a repeatable measurement using a standard color space, such as CIELAB, and the use of a perceptually based color difference formula, e.g. (Delta) ECMC color difference formula. Image based color sensors used for on-line measurement are not colorimetric by nature and require a non-linear transformation of the component colors based on the spectral properties of the incident illumination, imaging sensor, and the actual textile color. This research and development effort describes a benchtop, proof-of-principle system that implements a projection onto convex sets (POCS) algorithm for mapping component color measurements to standard tristimulus values and incorporates structural and color based segmentation for improved precision and accuracy. The POCS algorithm consists of determining the closed convex sets that describe the constraints on the reconstruction of the true tristimulus values based on the measured imperfect values. We show that using a simulated D65 standard illuminant, commercial filters and a CCD camera, accurate (under perceptibility limits) per-region based (Delta) ECMC values can be measured on real textile samples.

The 557.7 and 297.2 nm lines of O(1S) in the atmospheres of the terrestrial planets

NASA Astrophysics Data System (ADS)

Slanger, Tom; Sharpee, Brian; Pejakovic, Dusan; Gattinger, Richard; Llewellyn, Edward J.; McDade, Ian; Siskind, David; Minschwaner, Kenneth

There are few examples of spectral features in nightglows or in auroras which can be used for relative intensity calibration from space, particularly over a broad wavelength region. One potential candidate is the atomic oxygen line pair at 297.2 nm (the trans-auroral line) and 557.7 nm (the green line). They share the common O(1 S0 ) upper level, and therefore the observed intensity ratio of the O(1 S0 -1 D2 ) and O(1 S0 -3 P1 ) lines has a value that is a quantum-mechanical constant, equal to the ratio of the respective transition probabilities. The recently-published figure of 9.3 ± 0.5 [Gattinger et al., 2009] for I557.7 /I297.2 confirms the earlier value of 9.8 ± 1.0 [Slanger et al., 2006] as well as a previous estimate of 9 [Sharp and Siskind,1989] (all expressed in photon units). Such good agreement suggests that this value can be used for a two-point calibration of orbiting spectrometers where both lines can be observed. O(1 S) emission is seen in the atmospheres of all three terrestrial planets -Venus, Earth, Mars. Comparison with theory is less satisfactory. The current ratio of these transition probabilities recommended by NIST is 16.7, based on numerous calculations. This emphasizes the uncertain-ties inherent in making calculations on strongly forbidden transitions. For the O(1 S) case, the transition to O(3 P) proceeds by spin-orbit interaction, whereas that to O(1 D) involves electric quadrupole interaction. References Gattinger, R.L., et al., Can. J. Phys. 87, 1133, 2009 Sharp, W.E. and D.E. Siskind, Geophys. Res. Lett. 16, 1453, 1989 Slanger, T.G., et al., J. Geophys. Res. 111, A12318, 2006

Compressive Properties of Extruded Polytetrafluoroethylene

DTIC Science & Technology

2007-07-01

against equivalent temperature ( Tmap ) at a single strain rate (3map). This is a pragmatic, empirically based line- arization and extension to large strains...one of the strain rates that was used in the experimental program, and in this case two rates were used: 0.1 s1 and 3200 s1. The value Tmap , is...defined as Tmap ¼ Texp þA log _3map log _3exp ð11Þ where the subscript exp indicates the experimental values of strain rate and temperature. A

Multi-objective Decision Based Available Transfer Capability in Deregulated Power System Using Heuristic Approaches

NASA Astrophysics Data System (ADS)

Pasam, Gopi Krishna; Manohar, T. Gowri

2016-09-01

Determination of available transfer capability (ATC) requires the use of experience, intuition and exact judgment in order to meet several significant aspects in the deregulated environment. Based on these points, this paper proposes two heuristic approaches to compute ATC. The first proposed heuristic algorithm integrates the five methods known as continuation repeated power flow, repeated optimal power flow, radial basis function neural network, back propagation neural network and adaptive neuro fuzzy inference system to obtain ATC. The second proposed heuristic model is used to obtain multiple ATC values. Out of these, a specific ATC value will be selected based on a number of social, economic, deregulated environmental constraints and related to specific applications like optimization, on-line monitoring, and ATC forecasting known as multi-objective decision based optimal ATC. The validity of results obtained through these proposed methods are scrupulously verified on various buses of the IEEE 24-bus reliable test system. The results presented and derived conclusions in this paper are very useful for planning, operation, maintaining of reliable power in any power system and its monitoring in an on-line environment of deregulated power system. In this way, the proposed heuristic methods would contribute the best possible approach to assess multiple objective ATC using integrated methods.

Accurate collision-induced line-coupling parameters for the fundamental band of CO in He - Close coupling and coupled states scattering calculations

NASA Technical Reports Server (NTRS)

Green, Sheldon; Boissoles, J.; Boulet, C.

1988-01-01

The first accurate theoretical values for off-diagonal (i.e., line-coupling) pressure-broadening cross sections are presented. Calculations were done for CO perturbed by He at thermal collision energies using an accurate ab initio potential energy surface. Converged close coupling, i.e., numerically exact values, were obtained for coupling to the R(0) and R(2) lines. These were used to test the coupled states (CS) and infinite order sudden (IOS) approximate scattering methods. CS was found to be of quantitative accuracy (a few percent) and has been used to obtain coupling values for lines to R(10). IOS values are less accurate, but, owing to their simplicity, may nonetheless prove useful as has been recently demonstrated.

Revised and extended analysis of the eighth spectrum of platinum (Pt VIII)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Azarov, Vladimir I., E-mail: vlad_azarov@yahoo.com; Gayasov, Robert R.

2017-05-15

The spectrum of platinum was observed in the 300–2100 Å wavelength region. Grazing and normal incidence VUV spectrographs have been used to record the spectrum. The (5d{sup 3}+5d{sup 2}6s)−5d{sup 2}6p transition array of seven times ionized platinum, Pt VIII, has been investigated. The configurations 5d{sup 3} and 5d{sup 2}6p had been previously studied, and all levels of these configurations (19 and 45 levels, respectively) had been established. The previous analysis was based on 178 classified spectral lines. In the current analysis we have confirmed identification of all previously found levels and all but 10 previously assigned spectral lines, although we havemore » detected a large (up to 35 mÅ) systematic shift in wavelength measurements used in the previous analysis. Based on new wavelength measurements, we have corrected the 5d{sup 3} and 5d{sup 2}6p energy level values (by up to 55 cm{sup −1}) and established for the first time 14 out of 16 theoretically possible 5d{sup 2}6s levels in Pt VIII. The total list of identified lines (including 180 new lines) contains 349 entries. The orthogonal operators technique was used to calculate the level structure and transition probabilities. The energy parameters have been determined by the least squares fit to the observed levels. Calculated transition probability and energy values, as well as LS-compositions obtained from the fitted parameters are presented.« less

Discovery of antitumor ursolic acid long-chain diamine derivatives as potent inhibitors of NF-κB.

PubMed

Jiang, Wei; Huang, Ri-Zhen; Zhang, Jing; Guo, Tong; Zhang, Meng-Ting; Huang, Xiao-Chao; Zhang, Bin; Liao, Zhi-Xin; Sun, Jing; Wang, Heng-Shan

2018-05-08

A series of inhibitors of NF-κB based on ursolic acid (UA) derivatives containing long-chain diamine moieties were designed and synthesized as well as evaluated the antitumor effects. These compounds exhibited significant inhibitory activity to the NF-κB with IC 50 values at micromolar concentrations in A549 lung cancer cell line. Among them, compound 8c exerted potent activity against the test tumor cell lines including multidrug resistant human cancer lines, with the IC 50 values ranged from 5.22 to 8.95 μM. Moreover, compound 8c successfully suppressed the migration of A549 cells. Related mechanism study indicated compound 8c caused cell cycle arrest at G1 phase and triggered apoptosis in A549 cells through blockage of NF-κB signalling pathway. Molecular docking study revealed that key interactions between 8c and the active site of NF-κB in which the bulky and strongly electrophilic group of long-chain diamine moieties were important for improving activity. Copyright © 2018 Elsevier Inc. All rights reserved.

New metallicity calibration for Seyfert 2 galaxies based on the N2O2 index

NASA Astrophysics Data System (ADS)

Castro, C. S.; Dors, O. L.; Cardaci, M. V.; Hägele, G. F.

2017-05-01

We derive a new relation between the metallicity of Seyfert 2 active galactic nuclei (AGNs) and the intensity of the narrow emission-lines ratio N2O2 = log([N II] λ6584/[O II] λ3727). The calibration of this relation was performed by determining the metallicity (Z) of a sample of 58 AGNs through a diagram containing the observational data and the results of a grid of photoionization models obtained with the cloudy code. We find the new Z/Z⊙-N2O2 relation using the obtained metallicity values and the corresponding observational emission-line intensities for each object of the sample. Estimations derived through the use of this new calibration indicate that the narrow-line regions of Seyfert 2 galaxies exhibit a large range of metallicities (0.3 ≲ Z/Z⊙ ≲ 2.0), with a median value Z ≈ Z⊙. Regarding the possible existence of correlations between the luminosity L(Hβ), the electron density and the colour excess E(B - V) with the metallicity in this kind of objects, we do not find correlations between them.

A measurement of the width and shift of the Fe I 3719.94 A line broadened by helium. [for stellar atmosphere studies

NASA Technical Reports Server (NTRS)

Driver, R. D.; Lombardi, G.

1977-01-01

Results are reported for measurements of the widths and shifts of the overlapping helium-broadened profiles of the Fe I absorption lines at 3719.94 and 3722.56 A, which were performed in a ballistic piston compressor using a saturated solution of FeCl3 in ethanol. It is found that at 4000 K, the 3719.94-A line has a gamma/n (FWHM) value of approximately 5.2 billionths rad/sec per cu cm, the blue shift of this line corresponds to a beta/n value of about 0.49 billionth rad/sec per cu cm, and the 3722.56-A line has the same values. These results are compared with previous experimental determinations and with theoretical calculations of neutral-line broadening for the Fe I lines. The significance of these measurements with respect to the solar spectrum and cool DG white dwarfs is discussed.

Paraconsistent Reasoning for OWL 2

NASA Astrophysics Data System (ADS)

Ma, Yue; Hitzler, Pascal

A four-valued description logic has been proposed to reason with description logic based inconsistent knowledge bases. This approach has a distinct advantage that it can be implemented by invoking classical reasoners to keep the same complexity as under the classical semantics. However, this approach has so far only been studied for the basic description logic mathcal{ALC}. In this paper, we further study how to extend the four-valued semantics to the more expressive description logic mathcal{SROIQ} which underlies the forthcoming revision of the Web Ontology Language, OWL 2, and also investigate how it fares when adapted to tractable description logics including mathcal{EL++}, DL-Lite, and Horn-DLs. We define the four-valued semantics along the same lines as for mathcal{ALC} and show that we can retain most of the desired properties.

Gradient of the stellar magnetic field in measurements of hydrogen line cores

NASA Astrophysics Data System (ADS)

Kudryavtsev, Dimitry O.; Romanyuk, Iosif I.

2009-04-01

We report the observed systematic differences in longitudinal magnetic field values, obtained from measurements of metal lines and the core of the Hβ line for a number of Ap stars, having strong global magnetic fields. In overwhelming majority of cases the magnetic field values, obtained from measurements of hydrogen lines cores, is smaller then the ones obtained from metal lines. We discuss some possible explanations of this effect, the most probable of which is the existence of the gradient of the magnetic field in stellar atmospheres.

ASD-1000: High-resolution, high-temperature acetylene spectroscopic databank

NASA Astrophysics Data System (ADS)

Lyulin, O. M.; Perevalov, V. I.

2017-11-01

We present a high-resolution, high-temperature version of the Acetylene Spectroscopic Databank called ASD-1000. The databank contains the line parameters (position, intensity, Einstein coefficient for spontaneous emission, term value of the lower states, self- and air-broadening coefficients, temperature dependence exponents of the self- and air-broadening coefficients) of the principal isotopologue of C2H2. The reference temperature for line intensity is 296 K and the intensity cutoff is 10-27 cm-1/(molecule cm-2) at 1000 K. The databank has 33,890,981 entries and covers the 3-10,000 cm-1 spectral range. The databank is based on the global modeling of the line positions and intensities performed within the framework of the method of effective operators. The parameters of the effective Hamiltonian and the effective dipole moment operator have been fitted to the observed values of the line positions and intensities collected from the literature. The broadening coefficients as well as their temperature dependence exponents were calculated using the empirical equations. The databank is useful for studying high-temperature radiative properties of C2H2. ASD-1000 is freely accessible via the Internet site of V.E. Zuev Institute of Atmospheric Optics SB RAS ftp://ftp.iao.ru/pub/ASD1000/.

7 CFR 42.132 - Determining cumulative sum values.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Determining cumulative sum values. 42.132 Section 42... REGULATIONS STANDARDS FOR CONDITION OF FOOD CONTAINERS On-Line Sampling and Inspection Procedures § 42.132 Determining cumulative sum values. (a) The parameters for the on-line cumulative sum sampling plans for AQL's...

Children's Mental Representation When Comparing Fractions with Common Numerators

ERIC Educational Resources Information Center

Liu, Chunhui; Xin, Ziqiang; Lin, Chongde; Thompson, Clarissa A.

2013-01-01

Researchers debate whether one represents the magnitude of a fraction according to its real numerical value or just the discrete numerosity of its numerator or denominator. The present study examined three effects based on the notion that people possess a mental number line to explore how children represent fractions when they compare fractions…

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2012 CFR

2012-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2013 CFR

2013-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

40 CFR Appendix A to Subpart E of... - Cost-Effectiveness Analysis Guidelines

Code of Federal Regulations, 2014 CFR

2014-07-01

... of the resources which are attributable to the waste treatment management system or to one of its... end of the planning period. In this case, salvage value shall be estimated using straight line..., commercial and institutional sources, shall be based upon one of the following methods: (a) Preferred method...

Improving Teaching and Learning: Three Models to Reshape Educational Practice

ERIC Educational Resources Information Center

Roberson, Sam

2014-01-01

The work of schools is teaching and learning. However, the current educational culture is dominated by three characteristics: (1) the mechanistic view of organization and its practice based on the assembly line model where students progress along a value added conveyor; (2) the predominance of the Essentialist philosophy of education, in which the…

77 FR 34326 - Medicare Program; Hospital Inpatient Prospective Payment Systems for Acute Care Hospitals and the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-11

... Purchasing (VBP) Program, we inadvertently omitted data from the table entitled ``Proposed Performance..., Proposed Hospital Inpatient Value- Based Purchasing (VBP) Program Adjustment Factors for FY 2013, as a... partial paragraph-- (1) Lines 2 and 3, the phrase ``all hospitals are expected to experience a decrease...

Optimal Tuner Selection for Kalman Filter-Based Aircraft Engine Performance Estimation

NASA Technical Reports Server (NTRS)

Simon, Donald L.; Garg, Sanjay

2010-01-01

A linear point design methodology for minimizing the error in on-line Kalman filter-based aircraft engine performance estimation applications is presented. This technique specifically addresses the underdetermined estimation problem, where there are more unknown parameters than available sensor measurements. A systematic approach is applied to produce a model tuning parameter vector of appropriate dimension to enable estimation by a Kalman filter, while minimizing the estimation error in the parameters of interest. Tuning parameter selection is performed using a multi-variable iterative search routine which seeks to minimize the theoretical mean-squared estimation error. This paper derives theoretical Kalman filter estimation error bias and variance values at steady-state operating conditions, and presents the tuner selection routine applied to minimize these values. Results from the application of the technique to an aircraft engine simulation are presented and compared to the conventional approach of tuner selection. Experimental simulation results are found to be in agreement with theoretical predictions. The new methodology is shown to yield a significant improvement in on-line engine performance estimation accuracy

Oscillator strengths for ionized iron and manganese

NASA Technical Reports Server (NTRS)

De Boer, K. S.; Pottasch, S. R.; Morton, D. C.; York, D. G.

1974-01-01

The observed strengths of interstellar absorption lines of Fe II and Mn II in the spectra of alpha Vir, beta Cen, pi Sco, and zeta Oph along with laboratory f values of some of these lines between 2343 and 2606 A have been used to determine curves of growth for these ions and the f-values of ten lines of Fe II and three lines of Mn II between 1055 and 1261 A. The Fe and Mn abundances are derived.

Experimental and numerical study on thermal-hydraulic performance of wing-shaped-tubes-bundle equipped with winglet vortex generators

NASA Astrophysics Data System (ADS)

Abdelatief, Mohamed A.; Sayed Ahmed, Sayed Ahmed E.; Mesalhy, Osama M.

2018-03-01

The present work evaluates, experimentally and numerically, by the aid of commercial code FLUENT 6.3.26, the effects of relative locations (ΔX or ΔY), heights (hw), and span-angle (θ) of winglet-vortex-generators (WVGs) on thermal-hydraulic performance enhancement for down-stream and/or up-stream wing-shaped-tubes bundle heat exchangers for air Re ranging from 1.85 × 103 to 9.7 × 103 while water Re = 5 × 102. hw is set as 5 mm, 7.5 mm and 10 mm. For tube down-stream, θ is set as 0° (Base-line-case) and from 5° to 45° clockwise common-flow up (CFUp) and counterclockwise common-flow down (CFDn) while for tube up-stream it is set as -5°, -10° and -15° CFUp. Results show that the increase of θ counterclockwise-(CFDn) or clockwise-(CFUp) leads to increase the values of Nu number. Using WVGs with (+5 ° ≤ θ ≤ +45°) results in increasing Nu number by about from 34 to 48% comparing with that of base-line-case. The lowest values of drag coefficient ( f) for tube down-stream are obtained at +5° CFDn and -15° CFUp with respect to the base-line case. For tube up-stream, Nu number increases by increasing θ from 0° to -5° and the values of Nu number for θ varying from -5° to -15° have no significant changes. ( f) increases with hw and has negligible effect on ha. Furthermore, optimization analyses of θ and longitudinal fin (LF) are utilized, in four cases, for finding the optimum combination and maximum efficiency. The highest values of heat transfer parameters such as effectiveness (ɛ), area goodness factor (G) and efficiency index (η) and the lowest values of fluid-flow parameters like ( f) and hence the best efficiency, are achieved for -15° CFUp down-stream, ("case 3" of -15° CFUp down-stream and 6 mm LF height) and +5° CFDn down-stream. Correlations of Nu number, ( f) and (ɛ) as a function of θ and Re for the studied cases are performed.

Sharing moral values: anticipated ingroup respect as a determinant of adherence to morality-based (but not competence-based) group norms.

PubMed

Pagliaro, Stefano; Ellemers, Naomi; Barreto, Manuela

2011-08-01

This research examines how moral values regulate the behavior of individual group members. It argues that group members behave in line with moral group norms because they anticipate receiving ingroup respect when enacting moral values that are shared by ingroup members. Data from two experimental studies offer evidence in support. In Study 1 (N = 82), morality-based (but not competence-based) ingroup norms determined whether members of a low-status group opted for individual versus collective strategies for status improvement. This effect was mediated by anticipated ingroup respect and emerged regardless of whether group norms prescribed collectivistic or individualistic behavior. These effects were replicated in Study 2 (N = 69), where no comparable effect was found as a result of moral norms communicated by a higher status outgroup. This indicates that social identity implications rather than interdependence or more generic concerns about social approval or importance of cooperation drive these effects.

Photomask CD and LER characterization using Mueller matrix spectroscopic ellipsometry

NASA Astrophysics Data System (ADS)

Heinrich, A.; Dirnstorfer, I.; Bischoff, J.; Meiner, K.; Ketelsen, H.; Richter, U.; Mikolajick, T.

2014-10-01

Critical dimension and line edge roughness on photomask arrays are determined with Mueller matrix spectroscopic ellipsometry. Arrays with large sinusoidal perturbations are measured for different azimuth angels and compared with simulations based on rigorous coupled wave analysis. Experiment and simulation show that line edge roughness leads to characteristic changes in the different Mueller matrix elements. The influence of line edge roughness is interpreted as an increase of isotropic character of the sample. The changes in the Mueller matrix elements are very similar when the arrays are statistically perturbed with rms roughness values in the nanometer range suggesting that the results on the sinusoidal test structures are also relevant for "real" mask errors. Critical dimension errors and line edge roughness have similar impact on the SE MM measurement. To distinguish between both deviations, a strategy based on the calculation of sensitivities and correlation coefficients for all Mueller matrix elements is shown. The Mueller matrix elements M13/M31 and M34/M43 are the most suitable elements due to their high sensitivities to critical dimension errors and line edge roughness and, at the same time, to a low correlation coefficient between both influences. From the simulated sensitivities, it is estimated that the measurement accuracy has to be in the order of 0.01 and 0.001 for the detection of 1 nm critical dimension error and 1 nm line edge roughness, respectively.

Discovery of a cyclotron absorption line in the spectrum of the binary X-ray pulsar 4U 1538 - 52 observed by Ginga

NASA Technical Reports Server (NTRS)

Clark, George W.; Woo, Jonathan W.; Nagase, Fumiaki; Makishima, Kazuo; Sakao, Taro

1990-01-01

A cyclotron absorption line near 20 keV has been found in the spectrum of the massive eclipsing binary X-ray pulsar 4U 1538 - 52 in observations with the Ginga observatory. The line is detected throughout the 529 s pulse cycle with a variable equivalent width that has its maximum value during the smaller peak of the two-peak pulse profile. It is found that the profile of the pulse and the phase-dependence of the cyclotron line can be explained qualitatively by a pulsar model based on recent theoretical results on the properties of pencil beams emitted by accretion-heated slabs of magnetized plasma at the magnetic poles of a neutron star. The indicated field at the surface of the neutron star is 1.7 (1 + z) x 10 to the 12th G, where z is the gravitational redshift.

The research on the temperature measurement technology of aluminum atomic emission spectroscopy

NASA Astrophysics Data System (ADS)

Hu, Xiaotao; Hao, Xiaojian; Tang, Huijuan; Sun, Yongkai

2018-02-01

Aimed to the testing requirement of the transient high temperature in the bore of barrel weapon, which has the problems of high temperature, high pressure, high overload and narrow adverse environment, the photoelectric pyrometer was researched based on the temperature measurement technology of double line of atomic emission spectrum and storage measurement technology, which used silicon photomultiplier. Al I 690.6nm and 708.5nm were selected as the temperature measurement element spectral lines, spectral line intensity was converted into a voltage value by silicon photomultiplier, the temperature was obtained through the ratio of two spectrum lines. The temperature is measured by the photoelectric thermometer and the infrared thermometer when heating aluminum by oxyhydrogen flame, and the relative error was 1.75%. Results show the temperature dependence of the two methods is better, and prove the feasibility of the method.

Development of an artificial neural network model for risk assessment of skin sensitization using human cell line activation test, direct peptide reactivity assay, KeratinoSens™ and in silico structure alert parameter.

PubMed

Hirota, Morihiko; Ashikaga, Takao; Kouzuki, Hirokazu

2018-04-01

It is important to predict the potential of cosmetic ingredients to cause skin sensitization, and in accordance with the European Union cosmetic directive for the replacement of animal tests, several in vitro tests based on the adverse outcome pathway have been developed for hazard identification, such as the direct peptide reactivity assay, KeratinoSens™ and the human cell line activation test. Here, we describe the development of an artificial neural network (ANN) prediction model for skin sensitization risk assessment based on the integrated testing strategy concept, using direct peptide reactivity assay, KeratinoSens™, human cell line activation test and an in silico or structure alert parameter. We first investigated the relationship between published murine local lymph node assay EC3 values, which represent skin sensitization potency, and in vitro test results using a panel of about 134 chemicals for which all the required data were available. Predictions based on ANN analysis using combinations of parameters from all three in vitro tests showed a good correlation with local lymph node assay EC3 values. However, when the ANN model was applied to a testing set of 28 chemicals that had not been included in the training set, predicted EC3s were overestimated for some chemicals. Incorporation of an additional in silico or structure alert descriptor (obtained with TIMES-M or Toxtree software) in the ANN model improved the results. Our findings suggest that the ANN model based on the integrated testing strategy concept could be useful for evaluating the skin sensitization potential. Copyright © 2017 John Wiley & Sons, Ltd.

Estimating parametric phenotypes that determine anthesis date in Zea mays: Challenges in combining ecophysiological models with genetics

PubMed Central

Welch, Stephen M.; White, Jeffrey W.; Thorp, Kelly R.; Bello, Nora M.

2018-01-01

Ecophysiological crop models encode intra-species behaviors using parameters that are presumed to summarize genotypic properties of individual lines or cultivars. These genotype-specific parameters (GSP’s) can be interpreted as quantitative traits that can be mapped or otherwise analyzed, as are more conventional traits. The goal of this study was to investigate the estimation of parameters controlling maize anthesis date with the CERES-Maize model, based on 5,266 maize lines from 11 plantings at locations across the eastern United States. High performance computing was used to develop a database of 356 million simulated anthesis dates in response to four CERES-Maize model parameters. Although the resulting estimates showed high predictive value (R2 = 0.94), three issues presented serious challenges for use of GSP’s as traits. First (expressivity), the model was unable to express the observed data for 168 to 3,339 lines (depending on the combination of site-years), many of which ended up sharing the same parameter value irrespective of genetics. Second, for 2,254 lines, the model reproduced the data, but multiple parameter sets were equally effective (equifinality). Third, parameter values were highly dependent (p<10−6919) on the sets of environments used to estimate them (instability), calling in to question the assumption that they represent fundamental genetic traits. The issues of expressivity, equifinality and instability must be addressed before the genetic mapping of GSP’s becomes a robust means to help solve the genotype-to-phenotype problem in crops. PMID:29672629

New hydrazonoindolin-2-ones: Synthesis, exploration of the possible anti-proliferative mechanism of action and encapsulation into PLGA microspheres.

PubMed

Attia, Mohamed I; Eldehna, Wagdy M; Afifi, Samar A; Keeton, Adam B; Piazza, Gary A; Abdel-Aziz, Hatem A

2017-01-01

The synthesis and molecular characterization of new isatin-based hydrazonoindolin-2-ones 4a-o and 7a-e are reported. The in vitro anti-proliferative potential of the synthesized compounds 4a-o and 7a-e was examined against HT-29 (colon), ZR-75 (breast) and A549 (lung) human cancer cell lines. Compounds 7b, 7d and 7e were the most active congeners against the tested human cancer cell lines with average IC50 values of 4.77, 3.39 and 2.37 μM, respectively, as compared with the reference isatin-based drug, sunitinib, which exhibited an average IC50 value of 8.11 μM. Compound 7e was selected for further pharmacological evaluation in order to gain insight into its possible mechanism of action. It increased caspase 3/7 activity by 2.4- and 1.85-fold between 4 and 8 h of treatment, respectively, at 10 μM and it caused a decrease in the percentage of cells in the G1 phase of the cell cycle with a corresponding increase in the S-phase. In addition, compound 7e increased phosphorylated tyrosine (p-Tyr) levels nearly two-fold with an apparent IC50 value of 3.8 μM. The 7e-loaded PLGA microspheres were prepared using a modified emulsion-solvent diffusion method. The average encapsulation efficiency of the 7e-loaded PLGA microspheres was 85% ± 1.3. While, the in vitro release profile of the 7e-loaded microspheres was characterized by slow and continuous release of compound 7e during 21 days and the release curve was fitted to zero order kinetics. Incorporation of 7e into PLGA microspheres improved its in vitro anti-proliferative activity toward the human cancer cell line A549 after 120 h incubation period with an IC50 value less than 0.8 μM.

Continuum Foreground Polarization and Na I Absorption in Type Ia SNe

NASA Astrophysics Data System (ADS)

Zelaya, P.; Clocchiatti, A.; Baade, D.; Höflich, P.; Maund, J.; Patat, F.; Quinn, J. R.; Reilly, E.; Wang, L.; Wheeler, J. C.; Förster, F.; González-Gaitán, S.

2017-02-01

We present a study of the continuum polarization over the 400-600 nm range of 19 SNe Ia obtained with FORS at the VLT. We separate them into those that show Na I D lines at the velocity of their hosts and those that do not. Continuum polarization of the sodium sample near maximum light displays a broad range of values, from extremely polarized cases like SN 2006X to almost unpolarized ones like SN 2011ae. The non-sodium sample shows, typically, smaller polarization values. The continuum polarization of the sodium sample in the 400-600 nm range is linear with wavelength and can be characterized by the mean polarization ({P}{mean}). Its values span a wide range and show a linear correlation with color, color excess, and extinction in the visual band. Larger dispersion correlations were found with the equivalent width of the Na I D and Ca II H and K lines, and also a noisy relation between {P}{mean} and R V , the ratio of total to selective extinction. Redder SNe show stronger continuum polarization, with larger color excesses and extinctions. We also confirm that high continuum polarization is associated with small values of R V . The correlation between extinction and polarization—and polarization angles—suggest that the dominant fraction of dust polarization is imprinted in interstellar regions of the host galaxies. We show that Na I D lines from foreground matter in the SN host are usually associated with non-galactic ISM, challenging the typical assumptions in foreground interstellar polarization models. Based on observations made with ESO Telescopes at the Paranal Observatory under programs 068.D-0571(A), 069.D-0438(A), 070.D-0111(A), 076.D-0178(A), 079.D-0090(A), 080.D-0108(A), 081.D-0558(A), 085.D-0731(A), and 086.D-0262(A). Also based on observations collected at the German-Spanish Astronomical Center, Calar Alto (Spain).

Medical Products Research

NASA Technical Reports Server (NTRS)

1982-01-01

Ventrex Laboratories, Inc. develops, manufactures and markets a line of medical diagnostic assays based on biochemical techniques, in particular immunochemical techniques. Their products are sold worldwide to hospitals and medical laboratories for use in testing blood samples and other biological fluids. Analysis of a patient's body fluids, compared with normal values, aids a physician in confirming or otherwise diagnosing a suspected disease condition. NERAC's rapid information retrieval has provided Ventrex invaluable up-to-date information, and has permitted large scale savings. NERAC's service was particularly important in the development of a new product in the company's Ventre/Sep line, which is used in radioimmunoassays.

Analysis of the symbiotic star AG Pegasi

NASA Technical Reports Server (NTRS)

Keyes, C. D.; Plavec, M. J.

1981-01-01

High and low dispersion IUE data are analyzed in conjunction with coincident ground based spectrophotometric scans and supplementary infrared photometry of the symbiotic object AG Pegasi. The IUE observations yield an improved value of E(B-V) = 0.12. The two stellar components are easily recognized in the spectra. The cool component may be an M1.7 III star and the hot component appears to have T (sub eff) of approximately 30000 K. The emission lines observed in the ultraviolet indicate two or three distince emitting regions. Nebular component ultraviolet intercombination lines suggest an electron density of several times 10 billion/cu cm.

Object-based Mapping of the Circumpolar Taiga-Tundra Ecotone with MODIS Tree Cover

NASA Technical Reports Server (NTRS)

Ransom, Kenneth J.; Montesano, Paul M.; Nelson, Ross F.

2011-01-01

The circumpolar taiga-tundra ecotone was delineated using an image segmentation based mapping approach with multi-annual MODIS Vegetation Continuous Fields (VCF) tree cover data. Circumpolar tree canopy cover (TCC) throughout the ecotone was derived by averaging MODIS VCF data from 2000 - 2005 and adjusting the averaged values using linear equations relating MODIS TCC to Quickbird-derived tree cover estimates. The adjustment helped mitigate VCF's overestimation of tree cover in lightly forested regions. An image segmentation grouped pixels representing similar tree cover into polygonal features (objects) that form the map of the transition zone. Eachfeature represents an area much larger than the 500m MODIS pixel to characterize thepatterns of sparse forest patches on a regional scale. Comparisons of the adjusted average tree cover data were made with (1) two existing tree line definitions aggregated for each 1deg longitudinal interval in North America and Eurasia and (2) Landsat-derived Canadianproportion of forest cover for Canada. The adjusted TCC from MODIS VCF shows, on average, greater than 12% TCC for all but one regional zone at the intersection with independently delineated tree lines. Adjusted values track closely with Canadian proportion of forest cover data in areas of low tree cover. Those polygons near the boreal/tundra interface with either (1) mean adjusted TCC values between 5-20% , or (2) mean adjusted TCC values <5% but with a standard deviation > 5% were used to identify the ecotone.

Development of double-pulse lasers ablation system and electron paramagnetic resonance spectroscopy for direct spectral analysis of manganese doped PVA polymer

NASA Astrophysics Data System (ADS)

Khalil, A. A. I.; Morsy, M. A.; El-Deen, H. Z.

2017-11-01

Series of manganese-co-precipitated poly (vinyl alcohol) (PVA) polymer were quantitatively and qualitatively analyzed using laser ablation system (LAS) based on double-pulse laser induced breakdown spectroscopy (DP-LIBS) and electron paramagnetic resonance (EPR) spectroscopy. The collinear nanosecond laser beams of 266 and 1064 nm were optimized to focus on the surface of the PVA polymer target. Both laser beams were employed to estimate the natural properties of the excited Mn-PVA plasma, such as electron number density (Ne), electron temperature (Te), and Mn concentration. Individual transition lines of manganese (Mn), carbon (C), lithium (Li), hydrogen (H) and oxygen (O) atoms are identified based on the NIST spectral database. The results show better responses with DP-LIBS than the single-pulse laser induced breakdown spectroscopy (SP-LIBS). On the other hand, the EPR investigation shows characteristic broad peak of Mn-nano-particles (Mn-NPs) in the range of quantum dots of superparamagnetic materials. The line width (peak-to-peak, ΔHpp) and g-value of the observed Mn-EPR peak are ∼20 mT and 2.0046, respectively. The intensities of Mn-emission line at a wavelength 403.07 nm and the Mn-EPR absorption peak were used to accurate quantify the Mn-content in the polymer matrix. The results produce linear trends within the studied concentration range with regression coefficient (R2) value of ∼0.99, and limit of detection (LOD) of 0.026 mol.% and 0.016 mol.%, respectively. The LOD values are at a fold change of about -0.2 of the studied lowest mol.%. The proposed protocols of trace element detection are of significant advantage and can be applied to the other metal analysis.

Synthesis and evaluation of new benzodioxole-based dithiocarbamate derivatives as potential anticancer agents and hCA-I and hCA-II inhibitors.

PubMed

Altıntop, Mehlika Dilek; Sever, Belgin; Akalın Çiftçi, Gülşen; Kucukoglu, Kaan; Özdemir, Ahmet; Soleimani, Seyedeh Sara; Nadaroglu, Hayrunnisa; Kaplancıklı, Zafer Asım

2017-01-05

In the current work, new benzodioxole-based dithiocarbamate derivatives were synthesized via the reaction of N-(1,3-benzodioxol-5-ylmethyl)-2-chloroacetamide with appropriate sodium salts of N,N-disubstituted dithiocarbamic acids. These derivatives were evaluated for their cytotoxic effects on A549 human lung adenocarcinoma and C6 rat glioma cell lines. N-(1,3-Benzodioxol-5-ylmethyl)-2-[4-(4-nitrophenyl)-1-piperazinylthiocarbamoylthio]acetamide (10) can be identified as the most promising anticancer agent against C6 cell line due to its notable inhibitory effect on C6 cells with an IC 50 value of 23.33 ± 7.63 μg/mL when compared with cisplatin (IC 50  = 19.00 ± 5.29 μg/mL). On the other hand, compound 10 did not show any significant cytotoxic activity against A549 cell line. The compounds were also tested for their in vitro inhibitory effects on hCA-I and hCA-II. Generally, the tested compounds were more effective on CAs than acetazolamide, the reference agent. Among these compounds, N-(1,3-benzodioxol-5-ylmethyl)-2-[(morpholinyl)thiocarbamoylthio]acetamide (3) and N-(1,3-benzodioxol-5-ylmethyl)-2-[(thiomorpholinyl)thiocarbamoylthio]acetamide (4) were found to be the most effective compounds on hCA-I with IC 50 values of 0.346 nM and 0.288 nM, and hCA-II with IC 50 values of 0.287 nM and 0.338 nM, respectively. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Evidence-based review of clinical outcomes of guideline-recommended pharmacotherapies for generalized anxiety disorder.

PubMed

Bereza, Basil G; Machado, Márcio; Ravindran, Arun V; Einarson, Thomas R

2012-08-01

To quantify the rates of clinical outcomes of Canadian Psychiatric Association (CPA) guideline-recommended pharmacotherapies for generalized anxiety disorder (GAD) by drug classification within each treatment line. Evidence from original research cited by the CPA was included. Pooled analyses, duplicates, and studies with nonextractable data were excluded. Response, remission, and baseline-endpoint or mean reductions scores of the Hamilton Anxiety Rating Scale (HARS) were extracted. The Cochrane Collaboration's computer program, Review Manager, version 5, with a random effects model, was used to pool results. A total of 50 articles were cited as evidence for managing GAD by the CPA. There was sufficient evidence of remission with first- or third-line agents to pool reported rates, and with agents from all 3 treatment lines to pool response rates and reduction in HARS scores. The mean range of effect size varied considerably from study to study within each treatment line. Comparison of pooled remission rates between first- and second-line agents was not possible. While the range of values by drug and drug class overlapped, the summary results for the probability of response and reduction in HARS scores was greater for first-line, compared with second-line, treatments. Drug components for third-line treatments were heterogeneous and produced mixed results. Despite the abundance of evidence in its totality presented in the CPA guidelines, there is inadequate evidence to formulate recommendations based on the pooled results from this study alone. However, such analysis provides an additional resource for clinicians to make more effective treatment decisions for individual patients with GAD.

A fiber optic sensor for on-line non-touch monitoring of roll shape

NASA Astrophysics Data System (ADS)

Guo, Yuan; Qu, Weijian; Yuan, Qi

2009-07-01

Basing on the principle of reflective displacement fibre-optic sensor, a high accuracy non-touch on-line optical fibre sensor for detecting roll shape is presented. The principle and composition of the detection system and the operation process are expatiated also. By using a novel probe of three optical fibres in equal transverse space, the effects of fluctuations in the light source, reflective changing of target surface and the intensity losses in the fibre lines are automatically compensated. Meantime, an optical fibre sensor model of correcting static error based on BP artificial neural network (ANN) is set up. Also by using interpolation method and value filtering to process the signals, effectively reduce the influence of random noise and the vibration of the roll bearing. So the accuracy and resolution were enhanced remarkably. Experiment proves that the resolution is 1μm and the precision can reach to 0.1%. So the system reaches to the demand of practical production process.

Development of evaluation technique of GMAW welding quality based on statistical analysis

NASA Astrophysics Data System (ADS)

Feng, Shengqiang; Terasaki, Hidenri; Komizo, Yuichi; Hu, Shengsun; Chen, Donggao; Ma, Zhihua

2014-11-01

Nondestructive techniques for appraising gas metal arc welding(GMAW) faults plays a very important role in on-line quality controllability and prediction of the GMAW process. On-line welding quality controllability and prediction have several disadvantages such as high cost, low efficiency, complication and greatly being affected by the environment. An enhanced, efficient evaluation technique for evaluating welding faults based on Mahalanobis distance(MD) and normal distribution is presented. In addition, a new piece of equipment, designated the weld quality tester(WQT), is developed based on the proposed evaluation technique. MD is superior to other multidimensional distances such as Euclidean distance because the covariance matrix used for calculating MD takes into account correlations in the data and scaling. The values of MD obtained from welding current and arc voltage are assumed to follow a normal distribution. The normal distribution has two parameters: the mean µ and standard deviation σ of the data. In the proposed evaluation technique used by the WQT, values of MD located in the range from zero to µ+3 σ are regarded as "good". Two experiments which involve changing the flow of shielding gas and smearing paint on the surface of the substrate are conducted in order to verify the sensitivity of the proposed evaluation technique and the feasibility of using WQT. The experimental results demonstrate the usefulness of the WQT for evaluating welding quality. The proposed technique can be applied to implement the on-line welding quality controllability and prediction, which is of great importance to design some novel equipment for weld quality detection.

Optimal smoothing length scale for actuator line models of wind turbine blades based on Gaussian body force distribution: Wind energy, actuator line model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martínez-Tossas, L. A.; Churchfield, M. J.; Meneveau, C.

The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within large-eddy simulations (LES). In the ALM, the lift and drag forces are replaced by an imposed body force that is typically smoothed over several grid points using a Gaussian kernel with some prescribed smoothing width e. To date, the choice of e has most often been based on numerical considerations related to the grid spacing used in LES. However, especially for finely resolved LES with grid spacings on the order of or smaller than the chord length of the blade,more » the best choice of e is not known. In this work, a theoretical approach is followed to determine the most suitable value of e, based on an analytical solution to the linearized inviscid flow response to a Gaussian force. We find that the optimal smoothing width eopt is on the order of 14%-25% of the chord length of the blade, and the center of force is located at about 13%-26% downstream of the leading edge of the blade for the cases considered. These optimal values do not depend on angle of attack and depend only weakly on the type of lifting surface. It is then shown that an even more realistic velocity field can be induced by a 2-D elliptical Gaussian lift-force kernel. Some results are also provided regarding drag force representation.« less

Defining new criteria for selection of cell-based intestinal models using publicly available databases

PubMed Central

2012-01-01

Background The criteria for choosing relevant cell lines among a vast panel of available intestinal-derived lines exhibiting a wide range of functional properties are still ill-defined. The objective of this study was, therefore, to establish objective criteria for choosing relevant cell lines to assess their appropriateness as tumor models as well as for drug absorption studies. Results We made use of publicly available expression signatures and cell based functional assays to delineate differences between various intestinal colon carcinoma cell lines and normal intestinal epithelium. We have compared a panel of intestinal cell lines with patient-derived normal and tumor epithelium and classified them according to traits relating to oncogenic pathway activity, epithelial-mesenchymal transition (EMT) and stemness, migratory properties, proliferative activity, transporter expression profiles and chemosensitivity. For example, SW480 represent an EMT-high, migratory phenotype and scored highest in terms of signatures associated to worse overall survival and higher risk of recurrence based on patient derived databases. On the other hand, differentiated HT29 and T84 cells showed gene expression patterns closest to tumor bulk derived cells. Regarding drug absorption, we confirmed that differentiated Caco-2 cells are the model of choice for active uptake studies in the small intestine. Regarding chemosensitivity we were unable to confirm a recently proposed association of chemo-resistance with EMT traits. However, a novel signature was identified through mining of NCI60 GI50 values that allowed to rank the panel of intestinal cell lines according to their drug responsiveness to commonly used chemotherapeutics. Conclusions This study presents a straightforward strategy to exploit publicly available gene expression data to guide the choice of cell-based models. While this approach does not overcome the major limitations of such models, introducing a rank order of selected features may allow selecting model cell lines that are more adapted and pertinent to the addressed biological question. PMID:22726358

[Activities of Harvard College Observatory

NASA Technical Reports Server (NTRS)

Dalgarno, A.; Smith, Peter L.; Stark, G.; Yoshino, K.

2002-01-01

With support from this grant, we have: 1) Developed techniques for improving wavelengths and f-values for singly and doubly charged ions of the iron group and have improved the accuracy of Fe III wavelengths by an order of magnitude. New Fe II f-values have also resulted from this work. 2) Measured line oscillator strengths and photoabsorption cross sections for UV molecular spectral feature that have been, or could be, used for searches for and detection of molecules in diffuse and translucent interstellar clouds and for determination of molecular column densities there. In addition, we have determined other molecular parameters -- line assignments, wavelengths, and line widths -- that are essential for theoretical descriptions of the abundance, fractionation, and excitation of interstellar molecules and for comparison of predictions with observations. 3) Measured A-values for spin-changing and other weak lines in low-Z ions. When A-values are available, these spectral features are useful for astrophysical plasma density and temperature diagnostics. Such lines are also used in interstellar abundance determinations in cases where the stronger allowed lines are saturated in astronomical spectra. 4) Taken an activist approach to ensuring that, (i), astronomers have ready access to our data, and, (ii), avenues of communication between data users and producers are strengthened.

Disorder-induced losses in photonic crystal waveguides with line defects.

PubMed

Gerace, Dario; Andreani, Lucio Claudio

2004-08-15

A numerical analysis of extrinsic diffraction losses in two-dimensional photonic crystal slabs with line defects is reported. To model disorder, a Gaussian distribution of hole radii in the triangular lattice of airholes is assumed. The extrinsic losses below the light line increase quadratically with the disorder parameter, decrease slightly with increasing core thickness, and depend weakly on the hole radius. For typical values of the disorder parameter the calculated loss values of guided modes below the light line compare favorably with available experimental results.

Universal FFM Hydrogen Spectral Line Shapes Applied to Ions and Electrons

NASA Astrophysics Data System (ADS)

Mossé, C.; Calisti, A.; Ferri, S.; Talin, B.; Bureyeva, L. A.; Lisitsa, V. S.

2008-10-01

We present a method for the calculation of hydrogen spectral line shapes based on two combined approaches: Universal Model and FFM procedure. We start with the analytical functions for the intensities of the Stark components of radiative transitions between highly excited atomic states with large values of principal quantum numbers n,n'γ1, with Δn = n-n'≪n for the specific cases of Hn-α line (Δn = 1) and Hn-β line (Δn = 2). The FFM line shape is obtained by averaging on the electric field of the Hooper's field distribution for ion and electron perturber dynamics and by mixing the Stark components with a jumping frequency rate ve (vi) where v = N1/3u (N is electron density and u is the ion or electron thermal velocity). Finally, the total line shape is given by convolution of ion and electron line shapes. Hydrogen line shape calculations for Balmer Hα and Hβ lines are compared to experimental results in low density plasma (Ne˜1016-1017cm-3) and low electron temperature in order of 10 000K. This method relying on analytic expressions permits fast calculation of Hn-α and Hn-β lines of hydrogen and could be used in the study of the Stark broadening of radio recombination lines for high principal quantum number.

Two New PRP Conjugate Gradient Algorithms for Minimization Optimization Models.

PubMed

Yuan, Gonglin; Duan, Xiabin; Liu, Wenjie; Wang, Xiaoliang; Cui, Zengru; Sheng, Zhou

2015-01-01

Two new PRP conjugate Algorithms are proposed in this paper based on two modified PRP conjugate gradient methods: the first algorithm is proposed for solving unconstrained optimization problems, and the second algorithm is proposed for solving nonlinear equations. The first method contains two aspects of information: function value and gradient value. The two methods both possess some good properties, as follows: 1) βk ≥ 0 2) the search direction has the trust region property without the use of any line search method 3) the search direction has sufficient descent property without the use of any line search method. Under some suitable conditions, we establish the global convergence of the two algorithms. We conduct numerical experiments to evaluate our algorithms. The numerical results indicate that the first algorithm is effective and competitive for solving unconstrained optimization problems and that the second algorithm is effective for solving large-scale nonlinear equations.

Re: Penetration Behavior of Opposed Rows of Staggered Secondary Air Jets Depending on Jet Penetration Coefficient and Momentum Flux Ratio

NASA Technical Reports Server (NTRS)

Holdeman, James D.

2016-01-01

The purpose of this article is to explain why the extension of the previously published C = (S/Ho)sqrt(J) scaling for opposed rows of staggered jets wasn't directly successful in the study by Choi et al. (2016). It is not surprising that staggered jets from opposite sides do not pass each other at the expected C value, because Ho/D and sqrt(J) are much larger than the maximum in previous studies. These, and large x/D's, tend to suggest development of 2-dimensional flow. Although there are distinct optima for opposed rows of in-line jets, single-side injection, and opposed rows of staggered jets based on C, opposed rows of staggered jets provide as good or better mixing performance, at any C value, than opposed rows of in-line jets or jets from single-side injection.

Histone Deacetylase Inhibitors through Click Chemistry

PubMed Central

Shen, Jie; Woodward, Robert; Kedenburg, James Patrick; Liu, Xianwei; Chen, Min; Fang, Lanyan; Sun, Duxin; Wang, Peng George

2012-01-01

Histone deacetylase inhibitors (HDACi) are a relatively new class of chemotherapy agents. Herein, we report a click-chemistry based approach to the synthesis of HDACi. Fourteen agents were synthesized from the combination of two alkyne and seven azido precursors. The inhibition of HDAC1 and HDAC8 was then determined by in vitro enzymatic assays, after which the cytotoxicity was evaluated in the NCI human cancer cell line screen. A lead compound 5g (NSC746457) was discovered that inhibited HDAC1 at an IC50 value of 104 ± 30 nM and proved quite potent in the cancer cell line screen with GI50 values ranging from 3.92 μM to 10 nM. Thus, this click HDACi design has provided a new chemical scaffold that has not only revealed a lead compound, but one which is easily amendable to further structural modifications given the modular nature of this approach. PMID:19007204

NIR technology for on-line determination of superficial a(w) and moisture content during the drying process of fermented sausages.

PubMed

Collell, Carles; Gou, Pere; Arnau, Jacint; Muñoz, Israel; Comaposada, Josep

2012-12-01

Three different NIR equipment were evaluated based on their ability to predict superficial water activity (a(w)) and moisture content in two types of fermented sausages (with and without moulds on surface), using partial least squares (PLS) regression models. The instruments differed mainly in wavelength range, resolution and measurement configuration. The most accurate equipment was used in a new experiment to achieve robust models in sausages with different salt contents and submitted to different drying conditions. The models developed showed determination coefficients (R(2)(P)) values of 0.990, 0.910 and 0.984, and RMSEP values of 1.560%, 0.220% and 0.007% for moisture, salt and a(w) respectively. It was demonstrated that NIR spectroscopy could be a suitable non-destructive method for on-line monitoring and control of the drying process in fermented sausages. Copyright © 2012 Elsevier Ltd. All rights reserved.

Two New PRP Conjugate Gradient Algorithms for Minimization Optimization Models

PubMed Central

Yuan, Gonglin; Duan, Xiabin; Liu, Wenjie; Wang, Xiaoliang; Cui, Zengru; Sheng, Zhou

2015-01-01

Two new PRP conjugate Algorithms are proposed in this paper based on two modified PRP conjugate gradient methods: the first algorithm is proposed for solving unconstrained optimization problems, and the second algorithm is proposed for solving nonlinear equations. The first method contains two aspects of information: function value and gradient value. The two methods both possess some good properties, as follows: 1)β k ≥ 0 2) the search direction has the trust region property without the use of any line search method 3) the search direction has sufficient descent property without the use of any line search method. Under some suitable conditions, we establish the global convergence of the two algorithms. We conduct numerical experiments to evaluate our algorithms. The numerical results indicate that the first algorithm is effective and competitive for solving unconstrained optimization problems and that the second algorithm is effective for solving large-scale nonlinear equations. PMID:26502409

Estimate of the hadronic vacuum polarization disconnected contribution to the anomalous magnetic moment of the muon from lattice QCD

NASA Astrophysics Data System (ADS)

Chakraborty, Bipasha; Davies, C. T. H.; Koponen, J.; Lepage, G. P.; Peardon, M. J.; Ryan, S. M.

2016-04-01

The quark-line disconnected diagram is a potentially important ingredient in lattice QCD calculations of the hadronic vacuum polarization contribution to the anomalous magnetic moment of the muon. It is also a notoriously difficult one to evaluate. Here, for the first time, we give an estimate of this contribution based on lattice QCD results that have a statistically significant signal, albeit at one value of the lattice spacing and an unphysically heavy value of the u /d quark mass. We use HPQCD's method of determining the anomalous magnetic moment by reconstructing the Adler function from time moments of the current-current correlator at zero spatial momentum. Our results lead to a total (including u , d and s quarks) quark-line disconnected contribution to aμ of -0.15 % of the u /d hadronic vacuum polarization contribution with an uncertainty which is 1% of that contribution.

Towards evidence-based emergency medicine: best BETs from the Manchester Royal Infirmary. BET 4: Prognostic value of B-type natriuretic peptides (BNP and NT-proBNP) in community-acquired pneumonia.

PubMed

Hodgson, David; Nee, Patrick; Sultan, Laith

2012-10-01

A short cut review was carried out to establish the prognostic value of B-type natriuretic peptides (BNP and NT-proBNP) in community acquired pneumonia (CAP). Three cohort studies were directly relevant to the question. The author, date and country of publication, patient group studied, study type, relevant outcomes, results and study weaknesses of these papers are tabulated. The clinical bottom line was that B-type natriuretic peptides have prognostic value in CAP but further prospective studies were needed to assess their application in clinical practice.

Collisional Shift and Broadening of Iodine Spectral Lines in Air Near 543 nm

NASA Technical Reports Server (NTRS)

Fletcher, D. G.; McDaniel, J. C.

1995-01-01

The collisional processes that influence the absorption of monochromatic light by iodine in air have been investigated. Measurements were made in both a static cell and an underexpanded jet flow over the range of properties encountered in typical compressible-flow aerodynamic applications. Experimentally measured values of the collisional shift and broadening coefficients were 0.058 +/- 0.004 and 0.53 +/- 0.010 GHz K(exp 0.7)/torr, respectively. The measured shift value showed reasonable agreement with theoretical calculations based on Lindholm-Foley collisional theory for a simple dispersive potential. The measured collisional broadening showed less favorable agreement with the calculated value.

A crossbred reference population can improve the response to genomic selection for crossbred performance.

PubMed

Esfandyari, Hadi; Sørensen, Anders Christian; Bijma, Piter

2015-09-29

Breeding goals in a crossbreeding system should be defined at the commercial crossbred level. However, selection is often performed to improve purebred performance. A genomic selection (GS) model that includes dominance effects can be used to select purebreds for crossbred performance. Optimization of the GS model raises the question of whether marker effects should be estimated from data on the pure lines or crossbreds. Therefore, the first objective of this study was to compare response to selection of crossbreds by simulating a two-way crossbreeding program with either a purebred or a crossbred training population. We assumed a trait of interest that was controlled by loci with additive and dominance effects. Animals were selected on estimated breeding values for crossbred performance. There was no genotype by environment interaction. Linkage phase and strength of linkage disequilibrium between quantitative trait loci (QTL) and single nucleotide polymorphisms (SNPs) can differ between breeds, which causes apparent effects of SNPs to be line-dependent. Thus, our second objective was to compare response to GS based on crossbred phenotypes when the line origin of alleles was taken into account or not in the estimation of breeding values. Training on crossbred animals yielded a larger response to selection in crossbred offspring compared to training on both pure lines separately or on both pure lines combined into a single reference population. Response to selection in crossbreds was larger if both phenotypes and genotypes were collected on crossbreds than if phenotypes were only recorded on crossbreds and genotypes on their parents. If both parental lines were distantly related, tracing the line origin of alleles improved genomic prediction, whereas if both parental lines were closely related and the reference population was small, it was better to ignore the line origin of alleles. Response to selection in crossbreeding programs can be increased by training on crossbred genotypes and phenotypes. Moreover, if the reference population is sufficiently large and both pure lines are not very closely related, tracing the line origin of alleles in crossbreds improves genomic prediction.

Virtual sensors for on-line wheel wear and part roughness measurement in the grinding process.

PubMed

Arriandiaga, Ander; Portillo, Eva; Sánchez, Jose A; Cabanes, Itziar; Pombo, Iñigo

2014-05-19

Grinding is an advanced machining process for the manufacturing of valuable complex and accurate parts for high added value sectors such as aerospace, wind generation, etc. Due to the extremely severe conditions inside grinding machines, critical process variables such as part surface finish or grinding wheel wear cannot be easily and cheaply measured on-line. In this paper a virtual sensor for on-line monitoring of those variables is presented. The sensor is based on the modelling ability of Artificial Neural Networks (ANNs) for stochastic and non-linear processes such as grinding; the selected architecture is the Layer-Recurrent neural network. The sensor makes use of the relation between the variables to be measured and power consumption in the wheel spindle, which can be easily measured. A sensor calibration methodology is presented, and the levels of error that can be expected are discussed. Validation of the new sensor is carried out by comparing the sensor's results with actual measurements carried out in an industrial grinding machine. Results show excellent estimation performance for both wheel wear and surface roughness. In the case of wheel wear, the absolute error is within the range of microns (average value 32 μm). In the case of surface finish, the absolute error is well below Ra 1 μm (average value 0.32 μm). The present approach can be easily generalized to other grinding operations.

A Design Verification of the Parallel Pipelined Image Processings

NASA Astrophysics Data System (ADS)

Wasaki, Katsumi; Harai, Toshiaki

2008-11-01

This paper presents a case study of the design and verification of a parallel and pipe-lined image processing unit based on an extended Petri net, which is called a Logical Colored Petri net (LCPN). This is suitable for Flexible-Manufacturing System (FMS) modeling and discussion of structural properties. LCPN is another family of colored place/transition-net(CPN) with the addition of the following features: integer value assignment of marks, representation of firing conditions as marks' value based formulae, and coupling of output procedures with transition firing. Therefore, to study the behavior of a system modeled with this net, we provide a means of searching the reachability tree for markings.

Sound propagation and absorption in foam - A distributed parameter model.

NASA Technical Reports Server (NTRS)

Manson, L.; Lieberman, S.

1971-01-01

Liquid-base foams are highly effective sound absorbers. A better understanding of the mechanisms of sound absorption in foams was sought by exploration of a mathematical model of bubble pulsation and coupling and the development of a distributed-parameter mechanical analog. A solution by electric-circuit analogy was thus obtained and transmission-line theory was used to relate the physical properties of the foams to the characteristic impedance and propagation constants of the analog transmission line. Comparison of measured physical properties of the foam with values obtained from measured acoustic impedance and propagation constants and the transmission-line theory showed good agreement. We may therefore conclude that the sound propagation and absorption mechanisms in foam are accurately described by the resonant response of individual bubbles coupled to neighboring bubbles.

Standard line slopes as a measure of a relative matrix effect in quantitative HPLC-MS bioanalysis.

PubMed

Matuszewski, B K

2006-01-18

A simple experimental approach for studying and identifying the relative matrix effect (for example "plasma-to-plasma" and/or "urine-to-urine") in quantitative analyses by HPLC-MS/MS is described. Using as a database a large number of examples of methods developed in recent years in our laboratories, the relationship between the precision of standard line slopes constructed in five different lots of a biofluid (for example plasma) and the reliability of determination of concentration of an analyte in a particular plasma lot (or subject) was examined. In addition, the precision of standard line slopes was compared when stable isotope-labeled analytes versus analogs were used as internal standards (IS). Also, in some cases, a direct comparison of standard line slopes was made when different HPLC-MS interfaces (APCI versus ESI) were used for the assay of the same compound, using the same IS and the same sample preparation and chromatographic separation conditions. In selected cases, the precision of standard line slopes in five different lots of a biofluid was compared with precision values determined five times in a single lot. The results of these studies indicated that the variability of standard line slopes in different lots of a biofluid [precision of standard line slopes expressed as coefficient of variation, CV (%)] may serve as a good indicator of a relative matrix effect and, it is suggested, this precision value should not exceed 3-4% for the method to be considered reliable and free from the relative matrix effect liability. Based on the results presented, in order to assess the relative matrix effect in bioanalytical methods, it is recommended to perform assay precision and accuracy determination in five different lots of a biofluid, instead of repeat (n=5) analysis in the same, single biofluid lot, calculate standard line slopes and precision of these slopes, and to use <3-4% slope precision value as a guide for method applicability to support clinical studies. It was also demonstrated that when stable isotope-labeled analytes were used as internal standards, the precision of standard line slopes in five different lots of a biofluid was

Comparison of optical and electrical measurements of the pantograph-catenary contact force

NASA Astrophysics Data System (ADS)

Bocciolone, Marco; Bucca, Giuseppe; Collina, Andrea; Comolli, Lorenzo

2010-09-01

In railway engineering the monitoring of contact force between pantograph and catenary gives information about the interaction between the two systems and it is useful to check the status of the overhead line. Indeed the failure of the catenary is one of the main causes of out of order problems. This study was conducted in a test campaign on an underground train instrumented with sensors able to monitor the line status. One of the more important measured quantities is the pantograph contact force, and two measurement systems were implemented: one optical and another electrical. The optical one was based on FBG sensors applied on the pantograph collector strip; the electrical one was based on two load cells positioned at the sides of the collector strip. The in-line measurements show that the optical solution is very promising, providing very reliable results that can be successfully used in the monitoring application, allowing the determination of the critical point in the line. The thermal compensation of any FBG sensors is a known problem and here is no exception: a thermal compensator was used to get also mean value measurements and the results are discussed.

Student Difficulties in Socio-Scientific Argumentation and Decision-Making Research Findings: Crossing the Borders of Two Research Lines

ERIC Educational Resources Information Center

Acar, Omer; Turkmen, Lutfullah; Roychoudhury, Anita

2010-01-01

Students' poor argumentation in the context of socio-scientific issues has become a concern in science education. Identified problems associated with student argumentation in socio-scientific issues are misevaluation of evidence, naive nature of science conceptualizations, and inappropriate use of value-based reasoning. In this theoretical paper,…

NOAA Photo Library - Historical Fisheries Collection

Science.gov Websites

purpose of this study was to capture the state of the American fisheries at that time and to use the knowledge gained as a base line for future studies. Goode admirably succeeded in this, but at the same time of economic value at that time and also illustrated the state of fishing vessels, fishing gear

PROMIS (Procurement Management Information System)

NASA Technical Reports Server (NTRS)

1987-01-01

The PROcurement Management Information System (PROMIS) provides both detailed and summary level information on all procurement actions performed within NASA's procurement offices at Marshall Space Flight Center (MSFC). It provides not only on-line access, but also schedules procurement actions, monitors their progress, and updates Forecast Award Dates. Except for a few computational routines coded in FORTRAN, the majority of the systems is coded in a high level language called NATURAL. A relational Data Base Management System called ADABAS is utilized. Certain fields, called descriptors, are set up on each file to allow the selection of records based on a specified value or range of values. The use of like descriptors on different files serves as the link between the falls, thus producing a relational data base. Twenty related files are currently being maintained on PROMIS.

Blood plasma chemistries from wild mourning doves held in captivity.

PubMed

Schulz, J H; Bermudez, A J; Tomlinson, J L; Firman, J D; He, Z

2000-07-01

Despite the extensive amount of research conducted on mourning doves (Zenaida macroura), no biochemical reference values exist for this species. Our objective, therefore, was to establish base line clinical chemistry reference values for mourning doves to assist with establishing clinical diagnoses. Wild mourning doves were captured 19 March 1996 to 8 August 1996, and 6 February 1998 to 12 May 1998; blood samples were collected from 382 mourning doves. Plasma biochemical values were established for glucose, sodium, potassium, chloride, enzymatic CO2, albumin, total protein, globulin, calcium, phosphorus, cholesterol, magnesium, aspartate aminotransferase (AST), gamma glutamyl transferase (GGT), lactate dehydrogenase (LDH), and uric acid. These reference values are invaluable for determining diagnosis of diseases of the gastrointestinal, hepatic, renal, cardiovascular, musculoskeletal, and endocrine systems.

Real-time PCR assay is superior to other methods for the detection of mycoplasma contamination in the cell lines of the National Cell Bank of Iran.

PubMed

Molla Kazemiha, Vahid; Bonakdar, Shahin; Amanzadeh, Amir; Azari, Shahram; Memarnejadian, Arash; Shahbazi, Shirin; Shokrgozar, Mohammad Ali; Mahdian, Reza

2016-08-01

Mycoplasmas are the most important contaminants of cell cultures throughout the world. They are considered as a major problem in biological studies and biopharmaceutical economic issues. In this study, our aim was to find the best standard technique as a rapid method with high sensitivity, specificity and accuracy for the detection of mycoplasma contamination in the cell lines of the National Cell Bank of Iran. Thirty cell lines suspected to mycoplasma contamination were evaluated by five different techniques including microbial culture, indirect DNA DAPI staining, enzymatic mycoalert(®) assay, conventional PCR and real-time PCR. Five mycoplasma-contaminated cell lines were assigned as positive controls and five mycoplasma-free cell lines as negative controls. The enzymatic method was performed using the mycoalert(®) mycoplasma detection kit. Real-time PCR technique was conducted by PromoKine diagnostic kits. In the conventional PCR method, mycoplasma genus-specific primers were designed to analyze the sequences based on a fixed and common region on 16S ribosomal RNA with PCR product size of 425 bp. Mycoplasma contamination was observed in 60, 56.66, 53.33, 46.66 and 33.33 % of 30 different cell cultures by real-time PCR, PCR, enzymatic mycoalert(®), indirect DNA DAPI staining and microbial culture methods, respectively. The analysis of the results of the different methods showed that the real-time PCR assay was superior the other methods with the sensitivity, specificity, accuracy, predictive value of positive and negative results of 100 %. These values were 94.44, 100, 96.77, 100 and 92.85 % for the conventional PCR method, respectively. Therefore, this study showed that real-time PCR and PCR assays based on the common sequences in the 16S ribosomal RNA are reliable methods with high sensitivity, specificity and accuracy for detection of mycoplasma contamination in cell cultures and other biological products.

Midline Shift Threshold Value for Hemiparesis in Chronic Subdural Hematoma.

PubMed

Juković, Mirela F; Stojanović, Dejan B

2015-01-01

Chronic subdural hematoma (CSDH) has a variety of clinical presentations, with numerous neurological symptoms and signs. Hemiparesis is one of the leading signs that potentially indicates CSDH. Purpose of this study was to determine the threshold (cut-off) value of midsagittal line (MSL) shift after which hemiparesis is likely to appear. The study evaluated 83 patients with 53 unilateral and 30 bilateral CSDHs in period of three years. Evaluated computed tomography (CT) findings in patients with CSDH were diameter of the hematoma and midsagittal line shift, measured on non-contrast CT scan in relation with occurrence of hemiparesis. Threshold values of MSL shift for both types of CSDHs were obtained as maximal (equal) sensitivity and specificity (intersection of the curves). MSL is a good predictor for hemiparesis occurrence (total sample, AUROC 0.75, p=0.0001). Unilateral and bilateral CSDHs had different threshold values of the MSL for hemiparesis development. Results suggested that in unilateral CSDH the threshold values of MSL could be at 10 mm (AUROC=0.65; p=0.07). For bilateral CSDH the threshold level of MSL shift was 4.5 mm (AUROC=0.77; p=0.01). Our study pointed on the phenomenon that midsagittal line shift can predict hemiparesis occurrence. Hemiparesis in patients with bilateral CSDH was more related to midsagittal line shift compared with unilateral CSDH. When value of midsagittal line shift exceed the threshold level, hemiparesis occurs with certain probability.

Profitability Analysis with FTC (Federal Trade Commission) Line of Business and Census Establishment Data: An Evaluation of Data Bases.

DTIC Science & Technology

1985-12-01

essential In accomplishing what I had to do in the short period of time in which I had to do it. I thank Captain Scott Hagin who was always available as...teachers, and pastors who provided the foundation of character so essential In accomplishing a task such as this. Gregory P. Miles ) ~.Koi. -Acesion For...Is defined as: 13 S- . . .,. -. Price-cost margin = Value-added - Payrollalue of shipments Value of shipments (VShip) is essentially what an industry

Transient digitizer with displacement current samplers

DOEpatents

McEwan, T.E.

1996-05-21

A low component count, high speed sample gate, and digitizer architecture using the sample gates is based on use of a signal transmission line, a strobe transmission line and a plurality of sample gates connected to the sample transmission line at a plurality of positions. The sample gates include a strobe pickoff structure near the strobe transmission line which generates a charge displacement current in response to propagation of the strobe signal on the strobe transmission line sufficient to trigger the sample gate. The sample gate comprises a two-diode sampling bridge and is connected to a meandered signal transmission line at one end and to a charge-holding cap at the other. The common cathodes are reverse biased. A voltage step is propagated down the strobe transmission line. As the step propagates past a capacitive pickoff, displacement current i=c(dv/dT), flows into the cathodes, driving the bridge into conduction and thereby charging the charge-holding capacitor to a value related to the signal. A charge amplifier converts the charge on the charge-holding capacitor to an output voltage. The sampler is mounted on a printed circuit board, and the sample transmission line and strobe transmission line comprise coplanar microstrips formed on a surface of the substrate. Also, the strobe pickoff structure may comprise a planar pad adjacent the strobe transmission line on the printed circuit board. 16 figs.

Transient digitizer with displacement current samplers

DOEpatents

McEwan, Thomas E.

1996-01-01

A low component count, high speed sample gate, and digitizer architecture using the sample gates is based on use of a signal transmission line, a strobe transmission line and a plurality of sample gates connected to the sample transmission line at a plurality of positions. The sample gates include a strobe pickoff structure near the strobe transmission line which generates a charge displacement current in response to propagation of the strobe signal on the strobe transmission line sufficient to trigger the sample gate. The sample gate comprises a two-diode sampling bridge and is connected to a meandered signal transmission line at one end and to a charge-holding cap at the other. The common cathodes are reverse biased. A voltage step is propagated down the strobe transmission line. As the step propagates past a capacitive pickoff, displacement current i=c(dv/dT), flows into the cathodes, driving the bridge into conduction and thereby charging the charge-holding capacitor to a value related to the signal. A charge amplifier converts the charge on the charge-holding capacitor to an output voltage. The sampler is mounted on a printed circuit board, and the sample transmission line and strobe transmission line comprise coplanar microstrips formed on a surface of the substrate. Also, the strobe pickoff structure may comprise a planar pad adjacent the strobe transmission line on the printed circuit board.

Line transients with corona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saied, M.M.; Safar, Y.A.; Salama, M.H.

1987-01-01

This paper investigates the effect of corona on the electromagnetic transients along high voltage overhead lines. A method is presented to simulate the line by dividing it into a number of sections connected in cascade. For {ital n} line sections, the number of the unknown variables is 2{ital n} + 1. The method allows any waveform of the exciting voltage function, as well as any impedance loading condition. The corona is represented by voltage-dependent shunt current sources. A systematic way for writing a sufficient number of differential equations is shown. For their solution, a digital computer subroutine based on themore » Runge--Kutta--Verner method was used. An artificial frequency-dependent damping by means of linear resistors was used to suppress the Gibb's oscillations in the solution. The proposed method is applied to study the transients on a 40 km high voltage line with 30-ft flat phase spacing and a single 1.4 inch ACSR conductor per phase. The exciting voltage has a double-exponential impulse waveform. Solutions are given for three values of resistive loads Z{sub {ital c}}2Z{sub {ital c}} and Z{sub {ital c}}/2, where Z{sub {ital c}} is the line surge impedance. The results of two interesting cases of inductive and capacitive loads are also given. Physical interpretations for the different solutions are given. Also, the current-voltage duality between inductive and capacitive loads is recognized. The corona was found to attenuate and distort the travelling waves. For example, during one wave excursion, the reduction of the current wave peaks can reach values as high as 8.5%. The effect is more noticeable in the current than in the voltage waves. As expected, it increases also with the line corona losses. The effect of the increase of the line effective capacitance due to the corona discharge is also demonstrated.« less

'Economy' line foods from four supermarkets and brand name equivalents: a comparison of their nutrient contents and costs.

PubMed

Cooper, S; Nelson, M

2003-10-01

Achieving healthy eating targets for low income households can be difficult because of economic barriers. Several UK supermarkets have introduced 'value line' or 'economy line' foods to improve their attractiveness to low income consumers. The costs and nutrient contents of five 'economy' line products of four major English supermarkets - Asda, KwikSave, Sainsbury and Tesco - were compared with branded (but not 'own label') equivalents. Single samples of tinned tomatoes, long-life orange juice, potatoes, sausages and white bread were purchased in each supermarket. They represented items of potential importance in relation to 'healthy' choices in the shopping baskets of low income households. Nutrients analysed were fat, sodium, potassium, iron, calcium, vitamin C, and energy. Economy line foods had a nutrient composition similar to and often better than the branded goods. The economy line products frequently had nutrient contents more in line with the Balance of Good Health (e.g. lower fat and sodium) compared with the branded goods. In terms of nutrients per pence, the economy line products were far better value for money compared with the branded lines. Economy line foods represent excellent value for money and are not nutritionally inferior to the branded products. They have a potentially important role to play in the promotion of healthy eating, especially amongst low income households.

VIMOS Ultra-Deep Survey (VUDS): IGM transmission towards galaxies with 2.5 < z < 5.5 and the colour selection of high-redshift galaxies

NASA Astrophysics Data System (ADS)

Thomas, R.; Le Fèvre, O.; Le Brun, V.; Cassata, P.; Garilli, B.; Lemaux, B. C.; Maccagni, D.; Pentericci, L.; Tasca, L. A. M.; Zamorani, G.; Zucca, E.; Amorin, R.; Bardelli, S.; Cassarà, L.; Castellano, M.; Cimatti, A.; Cucciati, O.; Durkalec, A.; Fontana, A.; Giavalisco, M.; Grazian, A.; Hathi, N. P.; Ilbert, O.; Paltani, S.; Pforr, J.; Ribeiro, B.; Schaerer, D.; Scodeggio, M.; Sommariva, V.; Talia, M.; Tresse, L.; Vanzella, E.; Vergani, D.; Capak, P.; Charlot, S.; Contini, T.; Cuby, J. G.; de la Torre, S.; Dunlop, J.; Fotopoulou, S.; Koekemoer, A.; López-Sanjuan, C.; Mellier, Y.; Salvato, M.; Scoville, N.; Taniguchi, Y.; Wang, P. W.

2017-01-01

The observed UV rest-frame spectra of distant galaxies are the result of their intrinsic emission combined with absorption along the line of sight produced by the inter-galactic medium (IGM). Here we analyse the evolution of the mean IGM transmission Tr(Lyα) and its dispersion along the line of sight for 2127 galaxies with 2.5 < z < 5.5 in the VIMOS Ultra Deep Survey (VUDS). We fitted model spectra combined with a range of IGM transmission to the galaxy spectra using the spectral fitting algorithm GOSSIP+. We used these fits to derive the mean IGM transmission towards each galaxy for several redshift slices from z = 2.5 to z = 5.5. We found that the mean IGM transmission defined as Tr(Lyα) = e- τ (with τ as the HI optical depth) is 79%, 69%, 59%, 55%, and 46% at redshifts 2.75, 3.22, 3.70, 4.23, and 4.77, respectively. We compared these results to measurements obtained from quasar lines of sight and found that the IGM transmission towards galaxies is in excellent agreement with quasar values up to redshift z 4. We found tentative evidence for a higher IGM transmission at z ≥ 4 compared to results from QSOs, but a degeneracy between dust extinction and IGM prevents us from firmly concluding whether the internal dust extinction for star-forming galaxies at z > 4 takes a mean value significantly in excess of E(B-V) > 0.15. Most importantly, we found a large dispersion of IGM transmission along the lines of sight towards distant galaxies with 68% of the distribution within 10 to 17% of the median value in δz = 0.5 bins, similar to what is found on the lines of sight towards QSOs. We demonstrate that taking this broad range of IGM transmission into account is important when selecting high-redshift galaxies based on their colour properties (e.g. LBG or photometric redshiftselection) because failing to do so causes a significant incompleteness in selecting high-redshift galaxy populations. We finally discuss the observed IGM properties and speculate that the broad range of observed transmissions might be the result of cosmic variance and clustering along lines of sight. This clearly shows that the sources that cause this extinction need to be more completely modelled. Based on data obtained with the European Southern Observatory Very Large Telescope, Paranal, Chile, under Large Program 185.A-0791.

Calibration-Free Laser-Induced Breakdown Spectroscopy (CF-LIBS) with Standard Reference Line for the Analysis of Stainless Steel.

PubMed

Fu, Hongbo; Dong, Fengzhong; Wang, Huadong; Jia, Junwei; Ni, Zhibo

2017-08-01

In this work, calibration-free laser-induced breakdown spectroscopy (CF-LIBS) is used to analyze a certified stainless steel sample. Due to self-absorption of the spectral lines from the major element Fe and the sparse lines of trace elements, it is usually not easy to construct the Boltzmann plots of all species. A standard reference line method is proposed here to solve this difficulty under the assumption of local thermodynamic equilibrium so that the same temperature value for all elements present into the plasma can be considered. Based on the concentration and rich spectral lines of Fe, the Stark broadening of Fe(I) 381.584 nm and Saha-Boltzmann plots of this element are used to calculate the electron density and the plasma temperature, respectively. In order to determine the plasma temperature accurately, which is seriously affected by self-absorption, a pre-selection procedure for eliminating those spectral lines with strong self-absorption is employed. Then, one spectral line of each element is selected to calculate its corresponding concentration. The results from the standard reference lines with and without self-absorption of Fe are compared. This method allows us to measure trace element content and effectively avoid the adverse effects due to self-absorption.

Analysis and characterizations of planar transmission structures and components for superconducting and monolithic integrated circuits

NASA Technical Reports Server (NTRS)

Itoh, Tatsuo

1991-01-01

The analysis and modeling of superconducting planar transmission lines were performed. Theoretically, the highest possible Q values of superconducting microstrip line was calculated and, as a result, it provided the Q value that the experiment can aim for. As an effort to search for a proper superconducting transmission line structure, the superconducting microstrip line and coplanar waveguide were compared in terms of loss characteristics and their design aspects. Also, the research was expanded to a superconducting coplanar waveguide family in the microwave packaging environment. Theoretically, it was pointed out that the substrate loss is critical in the superconducting transmission line structures.

Improvements in Depression and Mental Health After Acceptance and Commitment Therapy are Related to Changes in Defusion and Values-Based Action.

PubMed

Bramwell, Kate; Richardson, Thomas

2018-01-01

Acceptance and commitment therapy (ACT) has been found to be effective for various mental health disorders but the processes through which it affects change remain unclear. Much process research in the area is on physical rather than mental health, and focuses on the broad concept of psychological flexibility with little research on specific mechanisms identified in theory such as fusion and values. This study explored whether there was a relationship between two of the main ACT processes (cognitive defusion and values) and levels of depression and distress. Thirty-three participants completed questionnaires at the start and end of their treatment measuring general mental health and distress, depression, levels of cognitive fusion and how much they were living in line with their values and how important their values were to them. Results showed reductions in levels of fusion and increases in values-based action were significantly related to reductions in distress and depression. There was no correlation between changes in values importance and changes in distress or depression. This study therefore suggests decreased defusion and increased values-based action is an important mechanism in the efficacy of ACT in those with depression and mental health problems. The study is however limited by a small sample size and future research with a sample large enough for mediation analysis would be beneficial.

An automatic optimum number of well-distributed ground control lines selection procedure based on genetic algorithm

NASA Astrophysics Data System (ADS)

Yavari, Somayeh; Valadan Zoej, Mohammad Javad; Salehi, Bahram

2018-05-01

The procedure of selecting an optimum number and best distribution of ground control information is important in order to reach accurate and robust registration results. This paper proposes a new general procedure based on Genetic Algorithm (GA) which is applicable for all kinds of features (point, line, and areal features). However, linear features due to their unique characteristics are of interest in this investigation. This method is called Optimum number of Well-Distributed ground control Information Selection (OWDIS) procedure. Using this method, a population of binary chromosomes is randomly initialized. The ones indicate the presence of a pair of conjugate lines as a GCL and zeros specify the absence. The chromosome length is considered equal to the number of all conjugate lines. For each chromosome, the unknown parameters of a proper mathematical model can be calculated using the selected GCLs (ones in each chromosome). Then, a limited number of Check Points (CPs) are used to evaluate the Root Mean Square Error (RMSE) of each chromosome as its fitness value. The procedure continues until reaching a stopping criterion. The number and position of ones in the best chromosome indicate the selected GCLs among all conjugate lines. To evaluate the proposed method, a GeoEye and an Ikonos Images are used over different areas of Iran. Comparing the obtained results by the proposed method in a traditional RFM with conventional methods that use all conjugate lines as GCLs shows five times the accuracy improvement (pixel level accuracy) as well as the strength of the proposed method. To prevent an over-parametrization error in a traditional RFM due to the selection of a high number of improper correlated terms, an optimized line-based RFM is also proposed. The results show the superiority of the combination of the proposed OWDIS method with an optimized line-based RFM in terms of increasing the accuracy to better than 0.7 pixel, reliability, and reducing systematic errors. These results also demonstrate the high potential of linear features as reliable control features to reach sub-pixel accuracy in registration applications.

Quantitative Structure-Cytotoxicity Relationship of Cinnamic Acid Phenetyl Esters.

PubMed

Uesawa, Yoshihiro; Sakagami, Hiroshi; Okudaira, Noriyuki; Toda, Kazuhiro; Takao, Koichi; Kagaya, Hajime; Sugita, Yoshiaki

2018-02-01

Many phenolic acid phenethyl esters possess diverse biological effects including antioxidant, cytoprotective, anti-inflammation and anti-tumor activities. However, most previous antitumor studies have not considered the cytotoxicity against normal cells. Ten cinnamic acid phenetyl esters were subjected to quantitative structure-activity relationship (QSAR) analysis, based on their cytotoxicity and tumor-specificity, in order to find their new biological activities. Cytotoxicity against four human oral squamous cell carcinoma cell lines and three oral normal mesenchymal cells was determined by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method. Tumor specificity (TS) was evaluated by the ratio of the mean 50% cytotoxic concentration (CC 50 ) against normal oral cells to that against human oral squamous cell carcinoma cell lines. Potency-selectivity expression (PSE) value was calculated by dividing the TS value by CC 50 against tumor cells. Apoptosis markers were detected by western blot analysis. Physicochemical, structural and quantum-chemical parameters were calculated based on the conformations optimized by force-field minimization. Western blot analysis demonstrated that [ 9 ] stimulated the cleavage of caspase-3, suggesting the induction of apoptosis. QSAR analysis demonstrated that TS values were correlated with shape, size and ionization potential. Chemical modification of the lead compound may be a potential choice for designing a new type of anticancer drugs. Copyright© 2018, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

A Quantitative Transmission Line Experiment

ERIC Educational Resources Information Center

Johnston, D. C.; Silbernagel, B. G.

1969-01-01

Describes modifications of a commercially available strip-type transmission line, which makes possible reproducible measurements of standing waves on the line. Experimental data yield values for the characteristic impedance, phase velocity and line wavelength of radiation in the transmission line, and the dielectric constant of material in the…

Comparison of Highly Resolved Model-Based Exposure ...

EPA Pesticide Factsheets

Human exposure to air pollution in many studies is represented by ambient concentrations from space-time kriging of observed values. Space-time kriging techniques based on a limited number of ambient monitors may fail to capture the concentration from local sources. Further, because people spend more time indoors, using ambient concentration to represent exposure may cause error. To quantify the associated exposure error, we computed a series of six different hourly-based exposure metrics at 16,095 Census blocks of three Counties in North Carolina for CO, NOx, PM2.5, and elemental carbon (EC) during 2012. These metrics include ambient background concentration from space-time ordinary kriging (STOK), ambient on-road concentration from the Research LINE source dispersion model (R-LINE), a hybrid concentration combining STOK and R-LINE, and their associated indoor concentrations from an indoor infiltration mass balance model. Using a hybrid-based indoor concentration as the standard, the comparison showed that outdoor STOK metrics yielded large error at both population (67% to 93%) and individual level (average bias between −10% to 95%). For pollutants with significant contribution from on-road emission (EC and NOx), the on-road based indoor metric performs the best at the population level (error less than 52%). At the individual level, however, the STOK-based indoor concentration performs the best (average bias below 30%). For PM2.5, due to the relatively low co

Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

NASA Astrophysics Data System (ADS)

Pries, V. V.; Proskuriakov, N. E.

2018-04-01

To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

Análisis de la región de alta temperatura en las estrellas Be y estudio de sus propiedades y geometría

NASA Astrophysics Data System (ADS)

Torres, A. F.; Ringuelet, A. E.

The aim of this study is to analyse the Hot Temperature Region (HTR) that surrounds the photospheres of Be stars. Consequently, we have chosen 54 Be stars of spectral types B0, B1, B2, B3, B8 and B9; the sample is representative of a considerable range of temperature. We have analysed different lines that originate in the HTR from archival IUE spectra reprocessed by the INES: He II λ1640, Si IV λλ1394, 1403 and Al III λλ1855, 1863. From the measured values, we derive several relations that provide information on the geometry and thermodynamical properties of the HTR. Our major findings can be summarised as follows: 1) The equivalent widths of the selected lines in the spectrum of the program stars persist with similar values through all v sin(i) inclinations. 2) The equivalent widths of the Si IV lines are well correlated with the kinetic energy expansion of the wind. This suggests that the dissipation of mechanical energy in the HTR is an important source of heating. 3) The He II lines formation region, which is located at the dense base of the wind, shows full spherical symmetry. 4) The formation region of Si IV lines is located in a low-density well-developed wind and it extends over very high latitudes (˜75o). 5) The Al III lines are formed in an elongated region which is the beginning of the cool envelope. The analysis followed in this work has been completely independent from any theoretical model. Consequently, these results will be useful for deciding whether the circunstellar envelope of Be stars has an ellipsoidal geometry or a disklike shape.

The phallic castration complex and primary femininity: paired developmental lines toward female gender identity.

PubMed

Mayer, E L

1995-01-01

I suggest that two developmental lines contribute to the achievement of female gender identity. One is rooted in the phallic castration complex, and the other in primary femininity. Far from being mutually exclusive, the two comprise necessary aspects of every girl's progress toward becoming a woman. To that extent, every woman's analysis will include the analysis of compromise formations that emerge from both. In distinguishing clinical manifestations of each developmental line, I suggest that it may be useful to conceptualize primary femininity and the phallic castration complex as affect-defense configurations which incorporate two fundamentally different ideas about danger. In conflicts of primary femininity, danger is anticipated: anxiety is the signal for compromise formation, since what is actually possessed (the female genital) is valued and is therefore imagined as subject to danger. In the phallic castration complex, danger is imagined already to have occurred. Depressive affect becomes the primary motive for defense, based on a fantasy that what is valued (the male genital) has already been lost. This distinction may facilitate our efforts to specify exactly how recent revisions in theories of female development have explicit implications for practice.

Temporal variations of electron density and temperature in Kr/Ne/H2 photoionized plasma induced by nanosecond pulses from extreme ultraviolet source

NASA Astrophysics Data System (ADS)

Saber, I.; Bartnik, A.; Wachulak, P.; Skrzeczanowski, W.; Jarocki, R.; Fiedorowicz, H.

2017-06-01

Spectral investigations of low-temperature photoionized plasmas created in a Kr/Ne/H2 gas mixture were performed. The low-temperature plasmas were generated by gas mixture irradiation using extreme ultraviolet pulses from a laser-plasma source. Emission spectra in the ultraviolet/visible range from the photoionized plasmas contained lines that mainly corresponded to neutral atoms and singly charged ions. Temporal variations in the plasma electron temperature and electron density were studied using different characteristic emission lines at various delay times. Results, based on Kr II lines, showed that the electron temperature decreased from 1.7 to 0.9 eV. The electron densities were estimated using different spectral lines at each delay time. In general, except for the Hβ line, in which the electron density decreased from 3.78 × 1016 cm-3 at 200 ns to 5.77 × 1015 cm-3 at 2000 ns, most of the electron density values measured from the different lines were of the order of 1015 cm-3 and decreased slightly while maintaining the same order when the delay time increased. The time dependences of the measured and simulated intensities of a spectral line of interest were also investigated. The validity of the partial or full local thermodynamic equilibrium (LTE) conditions in plasma was explained based on time-resolved electron density measurements. The partial LTE condition was satisfied for delay times in the 200 ns to 1500 ns range. The results are summarized, and the dominant basic atomic processes in the gas mixture photoionized plasma are discussed.

Morphology of the interstellar cooling lines detected by COBE

NASA Technical Reports Server (NTRS)

Bennett, C. L.; Fixsen, D. J.; Hinshaw, G.; Mather, J. C.; Moseley, S. H.; Wright, E. L.; Eplee, R. E., Jr.; Gales, J.; Hewagama, T.; Isaacman, R. B.

1994-01-01

The Far-Infrared Absolute Spectrophotometer (FIRAS) on the COBE satellite has conducted an unbiased survey of the far-infrared emission from our Galaxy. The first results of this survey were reported by Wright et al. (1991). We report the results of new analyses of this spectral survey, which includes emission lines from 158 micrometer C(+), 122 and 205 micrometer N(+), 370 and 609 micrometer C(0), and CO J = 2 goes to 1 through J = 5 goes to 4. We report the morphological distribution along the Galactic plane (b = 0 deg) of the spectral line emission, and the high Galactic latitude intensities of the C(+) and 205 micrometer N(+) emission. In the Galactic plane the 205 micrometer line of N(+) generally follows the 158 micrometer C(+) line distribution, but the intensities scale as I(N(+) 205 micrometer) varies as I(C(+) 158 micrometer)(exp 1.5) toward the inner Galaxy. The high Galactic latitude intensity of the 158 micrometer fine-structure transition from C(+) is I(C(+) 158 micrometer) = (1.43 +/- 0.12) x 10(exp -6) csc (absolute value of b) ergs/sq cm s sr for absolute value of b greater than 15 deg, and it decreases more rapidly than the far-infrared intensity with increasing Galactic latitude. C(+) and neutral atomic hydrogen emission are closely correlated with a C(+) cooling rate of (2.65 +/- 0.15) x 10(exp -26) ergs/s. We conclude that this emission arises almost entirely from the cold neutral medium. The high Galactic latitude intensity of the 205 micrometer fine-structure transition from N(+) is I(N(+) 205 micrometer) = (4 +/- 1) x 10(exp -8) csc (absolute value of b) ergs/((sq cm)(s)(sr)) arising entirely from the warm ionized medium. We estimate the total ionizing photon rate in the Galaxy to be phi = 3.5 x 10(exp 53) ionizing photons per second, based on the 205 micrometer N(+) transition.

X-Ray Reflected Spectra from Accretion Disk Models. II. Diagnostic Tools for X-Ray Observations

NASA Technical Reports Server (NTRS)

Garcia, J.; Kallman, T. R.; Mushotzky, R. F.

2011-01-01

We present a comprehensive study of the emission spectra from accreting sources. We use our new reflection code to compute the reflected spectra from an accretion disk illuminated by X-rays. This set of models covers different values of ionization parameter, solar iron abundance and photon index for the illuminating spectrum. These models also include the most complete and recent atomic data for the inner-shell of the iron and oxygen isonuclear sequences. We concentrate our analysis to the 2 - 10 keV energy region, and in particular to the iron K-shell emission lines. We show the dependency of the equivalent width (EW) of the Fe Ka with the ionization parameter. The maximum value of the EW is approx. 800 eV for models with log Epsilon approx. 1.5, and decreases monotonically as Epsilon increases. For lower values of Epsilon the Fe K(alpha) EW decreases to a minimum near log Epsilon approx. 0.8. We produce simulated CCD observations based on our reflection models. For low ionized, reflection dominated cases, the 2 -10 keV energy region shows a very broad, curving continuum that cannot be represented by a simple power-law. We show that in addition to the Fe K-shell emission, there are other prominent features such as the Si and S L(alpha) lines, a blend of Ar VIII-XI lines, and the Ca x K(alpha) line. In some cases the S xv blends with the He-like Si RRC producing a broad feature that cannot be reproduced by a simple Gaussian profile. This could be used as a signature of reflection.

Integral field spectroscopy of selected areas of the Bright bar and Orion-S cloud in the Orion nebula

NASA Astrophysics Data System (ADS)

Mesa-Delgado, A.; Núñez-Díaz, M.; Esteban, C.; López-Martín, L.; García-Rojas, J.

2011-10-01

We present integral field spectroscopy of two selected zones in the Orion nebula obtained with the Potsdam Multi-Aperture Spectrophotometer, covering the optical spectral range from 3500 to 7200 Å and with a spatial resolution of 1 arcsec. The observed zones are located on the prominent Bright bar and on the brightest area at the north-east of the Orion south cloud, both containing remarkable ionization fronts. We obtain maps of emission-line fluxes and ratios, electron density and temperatures, and chemical abundances. We study the ionization structure and morphology of both fields, whose ionization fronts show different inclination angles with respect to the plane of the sky. We find that the maps of electron density, O+/H+ and O/H ratios show a rather similar structure. We interpret this as produced by the strong dependence on density of the [O II] lines used to derive the O+ abundance, and that our nominal values of electron density - derived from the [S II] line ratio - may be slightly higher than the appropriate value for the O+ zone. We measure the faint recombination lines of O II in the field at the north-east of the Orion south cloud, allowing us to explore the so-called abundance discrepancy problem. We find a rather constant abundance discrepancy across the field and a mean value similar to that determined in other areas of the Orion nebula, indicating that the particular physical conditions of this ionization front do not contribute to this discrepancy. Based on observations collected at the Centro Astronómico Hispano Alemán (CAHA) at Calar Alto, operated jointly by the Max-Planck Institut für Astronomie and the Instituto de Astrofísica de Andalucía (CSIC).

Genome-based prediction of test cross performance in two subsequent breeding cycles.

PubMed

Hofheinz, Nina; Borchardt, Dietrich; Weissleder, Knuth; Frisch, Matthias

2012-12-01

Genome-based prediction of genetic values is expected to overcome shortcomings that limit the application of QTL mapping and marker-assisted selection in plant breeding. Our goal was to study the genome-based prediction of test cross performance with genetic effects that were estimated using genotypes from the preceding breeding cycle. In particular, our objectives were to employ a ridge regression approach that approximates best linear unbiased prediction of genetic effects, compare cross validation with validation using genetic material of the subsequent breeding cycle, and investigate the prospects of genome-based prediction in sugar beet breeding. We focused on the traits sugar content and standard molasses loss (ML) and used a set of 310 sugar beet lines to estimate genetic effects at 384 SNP markers. In cross validation, correlations >0.8 between observed and predicted test cross performance were observed for both traits. However, in validation with 56 lines from the next breeding cycle, a correlation of 0.8 could only be observed for sugar content, for standard ML the correlation reduced to 0.4. We found that ridge regression based on preliminary estimates of the heritability provided a very good approximation of best linear unbiased prediction and was not accompanied with a loss in prediction accuracy. We conclude that prediction accuracy assessed with cross validation within one cycle of a breeding program can not be used as an indicator for the accuracy of predicting lines of the next cycle. Prediction of lines of the next cycle seems promising for traits with high heritabilities.

A Technique for Measuring Rotocraft Dynamic Stability in the 40 by 80 Foot Wind Tunnel

NASA Technical Reports Server (NTRS)

Gupta, N. K.; Bohn, J. G.

1977-01-01

An on-line technique is described for the measurement of tilt rotor aircraft dynamic stability in the Ames 40- by 80-Foot Wind Tunnel. The technique is based on advanced system identification methodology and uses the instrumental variables approach. It is particulary applicable to real time estimation problems with limited amounts of noise-contaminated data. Several simulations are used to evaluate the algorithm. Estimated natural frequencies and damping ratios are compared with simulation values. The algorithm is also applied to wind tunnel data in an off-line mode. The results are used to develop preliminary guidelines for effective use of the algorithm.

Canopy architectural and physiological characterization of near-isogenic wheat lines differing in the tiller inhibition gene tin.

PubMed

Moeller, Carina; Evers, Jochem B; Rebetzke, Greg

2014-01-01

Tillering is a core constituent of plant architecture, and influences light interception to affect plant and crop performance. Near-isogenic lines (NILs) varying for a tiller inhibition (tin) gene and representing two genetic backgrounds were investigated for tillering dynamics, organ size distribution, leaf area, light interception, red: far-red ratio, and chlorophyll content. Tillering ceased earlier in the tin lines to reduce the frequencies of later primary and secondary tillers compared to the free-tillering NILs, and demonstrated the genetically lower tillering plasticity of tin-containing lines. The distribution of organ sizes along shoots varied between NILs contrasting for tin. Internode elongation commenced at a lower phytomer, and the peduncle was shorter in the tin lines. The flag leaves of tin lines were larger, and the longest leaf blades were observed at higher phytomers in the tin than in free-tillering lines. Total leaf area was reduced in tin lines, and non-tin lines invested more leaf area at mid-canopy height. The tiller economy (ratio of seed-bearing shoots to numbers of shoots produced) was 10% greater in the tin lines (0.73-0.76) compared to the free-tillering sisters (0.62-0.63). At maximum tiller number, the red: far-red ratio (light quality stimulus that is thought to induce the cessation of tillering) at the plant-base was 0.18-0.22 in tin lines and 0.09-0.11 in free-tillering lines at levels of photosynthetic active radiation of 49-53% and 30-33%, respectively. The tin lines intercepted less radiation compared to their free-tillering sisters once genotypic differences in tiller numbers had established, and maintained green leaf area in the lower canopy later into the season. Greater light extinction coefficients (k) in tin lines prior to, but reduced k after, spike emergence indicated that differences in light interception between NILs contrasting in tin cannot be explained by leaf area alone but that geometric and optical canopy properties contributed. The careful characterization of specifically-developed NILs is refining the development of a physiology-based model for tillering to improve understanding of the value of architectural traits for use in cereal improvement.

On-board adaptive model for state of charge estimation of lithium-ion batteries based on Kalman filter with proportional integral-based error adjustment

NASA Astrophysics Data System (ADS)

Wei, Jingwen; Dong, Guangzhong; Chen, Zonghai

2017-10-01

With the rapid development of battery-powered electric vehicles, the lithium-ion battery plays a critical role in the reliability of vehicle system. In order to provide timely management and protection for battery systems, it is necessary to develop a reliable battery model and accurate battery parameters estimation to describe battery dynamic behaviors. Therefore, this paper focuses on an on-board adaptive model for state-of-charge (SOC) estimation of lithium-ion batteries. Firstly, a first-order equivalent circuit battery model is employed to describe battery dynamic characteristics. Then, the recursive least square algorithm and the off-line identification method are used to provide good initial values of model parameters to ensure filter stability and reduce the convergence time. Thirdly, an extended-Kalman-filter (EKF) is applied to on-line estimate battery SOC and model parameters. Considering that the EKF is essentially a first-order Taylor approximation of battery model, which contains inevitable model errors, thus, a proportional integral-based error adjustment technique is employed to improve the performance of EKF method and correct model parameters. Finally, the experimental results on lithium-ion batteries indicate that the proposed EKF with proportional integral-based error adjustment method can provide robust and accurate battery model and on-line parameter estimation.

Fabrication and characterization of chalcogenide polarization-maintaining fibers based on extrusion

NASA Astrophysics Data System (ADS)

Jiang, Ling; Wang, Xunsi; Guo, Fangxia; Wu, Bo; Zhao, Zheming; Mi, Nan; Li, Xing; Dai, Shixun; Liu, Zijun; Nie, Qiuhua; Wang, Rongping

2017-12-01

The fabrication and characterization of IR chalcogenide polarization-maintaining (PM) step-index optical fibers with elliptical-core and 1-in-line-core have been reported for the first time. An improved isolated co-extrusion method was used to fabricate these core-shaped PM fibers. The elliptical core had a horizontal radius of a = 3.66 μm, vertical radius of b = 1.83 μm and the 1-in-line core of a = 4.83 μm, b = 1.42 μm, respectively. Single-mode PM beam spots were observed for the elliptical-core and 1-in-line-core fibers in the near-field energy distributions. The highest values of birefringence of the elliptical-core and 1-in-line-core fibers are 2.09 × 10-4 at 2.7 μm and 3.272 × 10-4 at 2.8 μm, respectively. The extinction ratios of -3.7 dB and -2 dB were achieved in fibers of 0.5 m long with elliptical-core and 1-in-line-core, respectively.

Exact results for the O( N ) model with quenched disorder

NASA Astrophysics Data System (ADS)

Delfino, Gesualdo; Lamsen, Noel

2018-04-01

We use scale invariant scattering theory to exactly determine the lines of renormalization group fixed points for O( N )-symmetric models with quenched disorder in two dimensions. Random fixed points are characterized by two disorder parameters: a modulus that vanishes when approaching the pure case, and a phase angle. The critical lines fall into three classes depending on the values of the disorder modulus. Besides the class corresponding to the pure case, a second class has maximal value of the disorder modulus and includes Nishimori-like multicritical points as well as zero temperature fixed points. The third class contains critical lines that interpolate, as N varies, between the first two classes. For positive N , it contains a single line of infrared fixed points spanning the values of N from √{2}-1 to 1. The symmetry sector of the energy density operator is superuniversal (i.e. N -independent) along this line. For N = 2 a line of fixed points exists only in the pure case, but accounts also for the Berezinskii-Kosterlitz-Thouless phase observed in presence of disorder.

Dynamic Geometry Software and Tracing Tangents in the Context of the Mean Value Theorem: Technique and Theory Production

ERIC Educational Resources Information Center

Martínez-Hernández, Cesar; Ulloa-Azpeitia, Ricardo

2017-01-01

Based on the theoretical elements of the instrumental approach to tool use known as Task-Technique-Theory (Artigue, 2002), this paper analyses and discusses the performance of graduate students enrolled in a Teacher Training program. The latter performance relates to tracing tangent lines to the curve of a quadratic function in Dynamic Geometry…

Examining Value Change in MOOCs in the Scope of Connectivism and Open Educational Resources Movement

ERIC Educational Resources Information Center

Ozturk, Hayriye Tugba

2015-01-01

Massive Open Online Courses (MOOCs) came to prominence with Open Educational Resources Movement (OERM). It was based upon the idea of libre in removal of some permission barriers and gratis in removing the price barrier (Suber, 2008) in learning resources. In line with the theoretical underpinnings of OERM, MOOCs embody primary characteristics of…

Spectroscopic mapping of the physical properties of supernova remnant N 49

NASA Astrophysics Data System (ADS)

Pauletti, D.; Copetti, M. V. F.

2016-10-01

Context. Physical conditions inside a supernova remnant can vary significantly between different positions. However, typical observational data of supernova remnants are integrated data or contemplate specific portions of the remnant. Aims: We study the spatial variation in the physical properties of the N 49 supernova remnant based on a spectroscopic mapping of the whole nebula. Methods: Long-slit spectra were obtained with the slit (~4' × 1.03″) aligned along the east-west direction from 29 different positions spaced by 2″ in declination. A total of 3248 1D spectra were extracted from sections of 2″ of the 2D spectra. More than 60 emission lines in the range 3550 Å to 8920 Å were measured in these spectra. Maps of the fluxes and of intensity ratios of these emission lines were built with a spatial resolution of 2″ × 2″. Results: An electron density map has been obtained using the [S II] λ6716 /λ6731 line ratio. Values vary from ~500 cm-3 at the northeast region to more than 3500 cm-3 at the southeast border. We calculated the electron temperature using line ratio sensors for the ions S+, O++, O+, and N+. Values are about 3.6 × 104 K for the O++ sensor and about 1.1 × 104 K for other sensors. The Hα/Hβ ratio map presents a ring structure with higher values that may result from collisional excitation of hydrogen. We detected an area with high values of [N II] λ6583/Hα extending from the remnant center to its northeastern border, which may be indicating an overabundance of nitrogen in the area due to contamination by the progenitor star. We found a radial dependence in many line intensity ratio maps. We observed an increase toward the remnant borders of the intensity ratio of any two lines in which the numerator comes before in the sequence [O III] λ5007, [O III] λ4363, [Ar III] λ7136, [Ne III] λ3869, [O II] λ7325, [O II] λ3727, He II λ4686, Hβ λ4861, [N II] λ6583, He I λ6678, [S II] λ6731, [S II] λ6716, [O I] λ6300, [Ca II] λ7291, Ca II λ3934, and [N I] λ5199. Based on observations obtained at the Southern Astrophysical Research (SOAR) telescope, which is a joint project of the Ministério da Ciência, Tecnologia, e Inovação (MCTI) da República Federativa do Brasil, the US National Optical Astronomy Observatory (NOAO), the University of North Carolina at Chapel Hill (UNC), and Michigan State University (MSU).Maps as FITS files are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/595/A10

A pipeline VLSI design of fast singular value decomposition processor for real-time EEG system based on on-line recursive independent component analysis.

PubMed

Huang, Kuan-Ju; Shih, Wei-Yeh; Chang, Jui Chung; Feng, Chih Wei; Fang, Wai-Chi

2013-01-01

This paper presents a pipeline VLSI design of fast singular value decomposition (SVD) processor for real-time electroencephalography (EEG) system based on on-line recursive independent component analysis (ORICA). Since SVD is used frequently in computations of the real-time EEG system, a low-latency and high-accuracy SVD processor is essential. During the EEG system process, the proposed SVD processor aims to solve the diagonal, inverse and inverse square root matrices of the target matrices in real time. Generally, SVD requires a huge amount of computation in hardware implementation. Therefore, this work proposes a novel design concept for data flow updating to assist the pipeline VLSI implementation. The SVD processor can greatly improve the feasibility of real-time EEG system applications such as brain computer interfaces (BCIs). The proposed architecture is implemented using TSMC 90 nm CMOS technology. The sample rate of EEG raw data adopts 128 Hz. The core size of the SVD processor is 580×580 um(2), and the speed of operation frequency is 20MHz. It consumes 0.774mW of power during the 8-channel EEG system per execution time.

Simplified molecular input line entry system-based: QSAR modelling for MAP kinase-interacting protein kinase (MNK1).

PubMed

Begum, S; Achary, P Ganga Raju

2015-01-01

Quantitative structure-activity relationship (QSAR) models were built for the prediction of inhibition (pIC50, i.e. negative logarithm of the 50% effective concentration) of MAP kinase-interacting protein kinase (MNK1) by 43 potent inhibitors. The pIC50 values were modelled with five random splits, with the representations of the molecular structures by simplified molecular input line entry system (SMILES). QSAR model building was performed by the Monte Carlo optimisation using three methods: classic scheme; balance of correlations; and balance correlation with ideal slopes. The robustness of these models were checked by parameters as rm(2), r(*)m(2), [Formula: see text] and randomisation technique. The best QSAR model based on single optimal descriptors was applied to study in vitro structure-activity relationships of 6-(4-(2-(piperidin-1-yl) ethoxy) phenyl)-3-(pyridin-4-yl) pyrazolo [1,5-a] pyrimidine derivatives as a screening tool for the development of novel potent MNK1 inhibitors. The effects of alkyl group, -OH, -NO2, F, Cl, Br, I, etc. on the IC50 values towards the inhibition of MNK1 were also reported.

High-precision gravimetric survey in support of lunar laser ranging at Haleakala, Maui, 1976 - 1978

NASA Technical Reports Server (NTRS)

Schenck, B. E.; Laurila, S. H.

1978-01-01

The planning, observations and adjustment of high-precision gravity survey networks established on the islands of Maui and Oahu as part of the geodetic-geophysical program in support of lunar laser ranging at Haleakala, Maui, Hawaii are described. The gravity survey networks include 43 independently measured gravity differences along the gravity calibration line from Kahului Airport to the summit of Mt. Haleakala, together with some key points close to tidal gauges on Maui, and 40 gravity differences within metropolitan Honolulu. The results of the 1976-1978 survey are compared with surveys made in 1961 and in 1964-1965. All final gravity values are given in the system of the international gravity standardization net 1971 (IGSN 71); values are obtained by subtracting 14.57 mgal from the Potsdam value at the gravity base station at the Hickam Air Force Base, Honolulu.

Efficient Bayesian experimental design for contaminant source identification

NASA Astrophysics Data System (ADS)

Zhang, J.; Zeng, L.

2013-12-01

In this study, an efficient full Bayesian approach is developed for the optimal sampling well location design and source parameter identification of groundwater contaminants. An information measure, i.e., the relative entropy, is employed to quantify the information gain from indirect concentration measurements in identifying unknown source parameters such as the release time, strength and location. In this approach, the sampling location that gives the maximum relative entropy is selected as the optimal one. Once the sampling location is determined, a Bayesian approach based on Markov Chain Monte Carlo (MCMC) is used to estimate unknown source parameters. In both the design and estimation, the contaminant transport equation is required to be solved many times to evaluate the likelihood. To reduce the computational burden, an interpolation method based on the adaptive sparse grid is utilized to construct a surrogate for the contaminant transport. The approximated likelihood can be evaluated directly from the surrogate, which greatly accelerates the design and estimation process. The accuracy and efficiency of our approach are demonstrated through numerical case studies. Compared with the traditional optimal design, which is based on the Gaussian linear assumption, the method developed in this study can cope with arbitrary nonlinearity. It can be used to assist in groundwater monitor network design and identification of unknown contaminant sources. Contours of the expected information gain. The optimal observing location corresponds to the maximum value. Posterior marginal probability densities of unknown parameters, the thick solid black lines are for the designed location. For comparison, other 7 lines are for randomly chosen locations. The true values are denoted by vertical lines. It is obvious that the unknown parameters are estimated better with the desinged location.

A new hyperspectral imaging based device for quality control in plastic recycling

NASA Astrophysics Data System (ADS)

Bonifazi, G.; D'Agostini, M.; Dall'Ava, A.; Serranti, S.; Turioni, F.

2013-05-01

The quality control of contamination level in the recycled plastics stream has been identified as an important key factor for increasing the value of the recycled material by both plastic recycling and compounder industries. Existing quality control methods for the detection of both plastics and non-plastics contaminants in the plastic waste streams at different stages of the industrial process (e.g. feed, intermediate and final products) are currently based on the manual collection from the stream of a sample and on the subsequent off-line laboratory analyses. The results of such analyses are usually available after some hours, or sometimes even some days, after the material has been processed. The laboratory analyses are time-consuming and expensive (both in terms of equipment cost and their maintenance and of labour cost).Therefore, a fast on-line assessment to monitor the plastic waste feed streams and to characterize the composition of the different plastic products, is fundamental to increase the value of secondary plastics. The paper is finalized to describe and evaluate the development of an HSI-based device and of the related software architectures and processing algorithms for quality assessment of plastics in recycling plants, with particular reference to polyolefins (PO). NIR-HSI sensing devices coupled with multivariate data analysis methods was demonstrated as an objective, rapid and non-destructive technique that can be used for on-line quality and process control in the recycling process of POs. In particular, the adoption of the previous mentioned HD&SW integrated architectures can provide a solution to one of the major problems of the recycling industry, which is the lack of an accurate quality certification of materials obtained by recycling processes. These results could therefore assist in developing strategies to certify the composition of recycled PO products.

Genomic selection in sugar beet breeding populations.

PubMed

Würschum, Tobias; Reif, Jochen C; Kraft, Thomas; Janssen, Geert; Zhao, Yusheng

2013-09-18

Genomic selection exploits dense genome-wide marker data to predict breeding values. In this study we used a large sugar beet population of 924 lines representing different germplasm types present in breeding populations: unselected segregating families and diverse lines from more advanced stages of selection. All lines have been intensively phenotyped in multi-location field trials for six agronomically important traits and genotyped with 677 SNP markers. We used ridge regression best linear unbiased prediction in combination with fivefold cross-validation and obtained high prediction accuracies for all except one trait. In addition, we investigated whether a calibration developed based on a training population composed of diverse lines is suited to predict the phenotypic performance within families. Our results show that the prediction accuracy is lower than that obtained within the diverse set of lines, but comparable to that obtained by cross-validation within the respective families. The results presented in this study suggest that a training population derived from intensively phenotyped and genotyped diverse lines from a breeding program does hold potential to build up robust calibration models for genomic selection. Taken together, our results indicate that genomic selection is a valuable tool and can thus complement the genomics toolbox in sugar beet breeding.

Genetic parameters and selection of soybean lines based on selection indexes.

PubMed

Teixeira, F G; Hamawaki, O T; Nogueira, A P O; Hamawaki, R L; Jorge, G L; Hamawaki, C L; Machado, B Q V; Santana, A J O

2017-09-21

Defining selection criteria is important to obtain promising genotypes in a breeding program. The objective of this study was to estimate genetic parameters for agronomic traits and to perform soybean line selection using selection indices. The experiment was conducted at an experimental area located at Capim Branco farm, belonging to the Federal University of Uberlândia. A total of 37 soybean genotypes were evaluated in randomized complete block design with three replicates, in which twelve agronomic traits were evaluated. Analysis of variance, the Scott-Knott test at the 1 and 5% level of probability, and selection index analyses were performed. There was genetic variability for all agronomic traits, with medium to high levels of genotype determination coefficient. Twelve lines with a total cycle up to 110 days were observed and grouped with the cultivars MSOY 6101 and UFUS 7910. Three lines, UFUS FG 03, UFUS FG 20, and UFUS FG 31, were highlighted regarding grain yield with higher values than the national average of 3072 kg/ha. The direct selection enabled the highest trait individual gains. The Williams (1962) index and the Smith (1936) and Hazel (1943) index presented the highest selection gain for the grain yield character. The genotype-ideotype distance index and the index of the sum of ranks of Mulamba and Mock (1978) presented higher values of total selection gain. The lines UFUS FG 12, UFUS FG 14, UFUS FG 18, UFUS FG 25, and UFUS FG 31 were distinguished as superior genotypes by direct selection methods and selection indexes.

Decomposition of Composite Electric Field in a Three-Phase D-Dot Voltage Transducer Measuring System

PubMed Central

Hu, Xueqi; Wang, Jingang; Wei, Gang; Deng, Xudong

2016-01-01

In line with the wider application of non-contact voltage transducers in the engineering field, transducers are required to have better performance for different measuring environments. In the present study, the D-dot voltage transducer is further improved based on previous research in order to meet the requirements for long-distance measurement of electric transmission lines. When measuring three-phase electric transmission lines, problems such as synchronous data collection and composite electric field need to be resolved. A decomposition method is proposed with respect to the superimposed electric field generated between neighboring phases. The charge simulation method is utilized to deduce the decomposition equation of the composite electric field and the validity of the proposed method is verified by simulation calculation software. With the deduced equation as the algorithm foundation, this paper improves hardware circuits, establishes a measuring system and constructs an experimental platform for examination. Under experimental conditions, a 10 kV electric transmission line was tested for steady-state errors, and the measuring results of the transducer and the high-voltage detection head were compared. Ansoft Maxwell Stimulation Software was adopted to obtain the electric field intensity in different positions under transmission lines; its values and the measuring values of the transducer were also compared. Experimental results show that the three-phase transducer is characterized by a relatively good synchronization for data measurement, measuring results with high precision, and an error ratio within a prescribed limit. Therefore, the proposed three-phase transducer can be broadly applied and popularized in the engineering field. PMID:27754340

Digital Model of Railway Electric Traction Lines

NASA Astrophysics Data System (ADS)

Garg, Rachana; Mahajan, Priya; Kumar, Parmod

2017-08-01

The characteristic impedance and propagation constant define the behavior of signal propagation over the transmission lines. The digital model for railway traction lines which includes railway tracks is developed, using curve fitting technique in MATLAB. The sensitivity of this model has been computed with respect to frequency. The digital sensitivity values are compared with the values of analog sensitivity. The developed model is useful for digital protection, integrated operation, control and planning of the system.

Molybdenum electron impact width parameter measurement by laser-induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Sternberg, E. M. A.; Rodrigues, N. A. S.; Amorim, J.

2016-01-01

In this work, we suggest a method for electron impact width parameter calculation based on Stark broadening of emission lines of a laser-ablated plasma plume. First, electron density and temperature must be evaluated by means of the Saha-Boltzmann plot method for neutral and ionized species of the plasma. The method was applied for laser-ablated molybdenum plasma plume. For molybdenum plasma electron temperature, which varies around 10,000 K, and electron density, which reaches values around 1018 cm-3, and considering that total measured line broadening was due experimental and Stark broadening mainly, electron impact width parameter of molybdenum emission lines was determined as (0.01 ± 0.02) nm. Intending to validate the presented method, it was analyzed the laser-ablated aluminum plasma plume and the obtained results were in agreement with the predicted on the literature.

238U Mössbauer study on the magnetic properties of uranium-based heavy fermion superconductors

NASA Astrophysics Data System (ADS)

Tsutsui, Satoshi; Nakada, Masami; Nasu, Saburo; Haga, Yoshinori; Honma, Tetsuo; Yamamoto, Etsuji; Ohkuni, Hitoshi; Ōnuki, Yoshichika

2000-07-01

We have performed 238U Mössbauer spectroscopy of uranium-based heavy fermion superconductors, UPd2Al3 and URu2Si2, in order to investigate their physical properties, mainly their magnetic properties. The slow relaxation of magnetic hyperfine interaction in a paramagnetic state and the static hyperfine field has been observed in an antiferromagnetic ordered state for each compound. The line-widths have maximum at their characteristic temperatures where their magnetic susceptibilities have maximum values.

A quantum rings based on multiple quantum wells for 1.2-2.8 THz detection

NASA Astrophysics Data System (ADS)

Mobini, Alireza; Solaimani, M.

2018-07-01

In this paper optical properties of a new QR based on MQWs have been investigated for detection in the THz range. The QR composed of a periodic effective quantum sites that each one considered as QW in theta direction. Using Tight binding method, eigen value problem for a QR with circumstance of 100 nm number with different number of wells i.e. 2, 4, 6 and 8 are solved and the absorption spectrum have been calculated. The results show that absorption has maximum value in range of (1.2-2.88 THz) that can be used for THz detection. Finally, it is realized that by increasing the number of wells, the numbers of absorption line also increase.

Economic Development Benefits of New Transit Service: RiverLINE

DOT National Transportation Integrated Search

2010-06-01

This report documents the economic impacts of the RiverLINE, a light rail line connecting Trenton and Camden, New Jersey. The study examined whether and how the line impacted local land use, residential property values, travel behaviors and firm perf...

VizieR Online Data Catalog: Radial velocities of δ Sagittae (Pugh+, 2015)

NASA Astrophysics Data System (ADS)

Pugh, T.; Gray, D. F.; Griffin, R. F.

2018-01-01

28 spectra were obtained by Gray and Pugh between 2008 July and 2010 October (MJD 2454674-2455479) with the high-resolution (R~100000) coude spectrograph of the Elginfield Observatory of Western University (Gray 2009ApJ...697.1032G). The signal-to-noise ratios in the continuum, estimated from the photon counts, ranged from 152 to 314 with a mean of 220. The spectrograph has a dispersion of ~0.013 Å/mm and can reach a radial-velocity precision of 25 m/s by reference to water vapour lines inside the spectrograph (Gray & Brown 2006PASP..118.1112G). In the current case our measurement errors (based on exposures taken within a few nights of one another) range from 27 to 160 m/s, with a mean value of 90 m/s. The radial velocities were determined by measuring the positions of the spectral lines at 85 per cent of the line depth for 15 neutral metal lines in the λ6250-Å region. (1 data file).

Improved Seam-Line Searching Algorithm for UAV Image Mosaic with Optical Flow.

PubMed

Zhang, Weilong; Guo, Bingxuan; Li, Ming; Liao, Xuan; Li, Wenzhuo

2018-04-16

Ghosting and seams are two major challenges in creating unmanned aerial vehicle (UAV) image mosaic. In response to these problems, this paper proposes an improved method for UAV image seam-line searching. First, an image matching algorithm is used to extract and match the features of adjacent images, so that they can be transformed into the same coordinate system. Then, the gray scale difference, the gradient minimum, and the optical flow value of pixels in adjacent image overlapped area in a neighborhood are calculated, which can be applied to creating an energy function for seam-line searching. Based on that, an improved dynamic programming algorithm is proposed to search the optimal seam-lines to complete the UAV image mosaic. This algorithm adopts a more adaptive energy aggregation and traversal strategy, which can find a more ideal splicing path for adjacent UAV images and avoid the ground objects better. The experimental results show that the proposed method can effectively solve the problems of ghosting and seams in the panoramic UAV images.

Experimental research on femto-second laser damaging array CCD cameras

NASA Astrophysics Data System (ADS)

Shao, Junfeng; Guo, Jin; Wang, Ting-feng; Wang, Ming

2013-05-01

Charged Coupled Devices (CCD) are widely used in military and security applications, such as airborne and ship based surveillance, satellite reconnaissance and so on. Homeland security requires effective means to negate these advanced overseeing systems. Researches show that CCD based EO systems can be significantly dazzled or even damaged by high-repetition rate pulsed lasers. Here, we report femto - second laser interaction with CCD camera, which is probable of great importance in future. Femto - second laser is quite fresh new lasers, which has unique characteristics, such as extremely short pulse width (1 fs = 10-15 s), extremely high peak power (1 TW = 1012W), and especially its unique features when interacting with matters. Researches in femto second laser interaction with materials (metals, dielectrics) clearly indicate non-thermal effect dominates the process, which is of vast difference from that of long pulses interaction with matters. Firstly, the damage threshold test are performed with femto second laser acting on the CCD camera. An 800nm, 500μJ, 100fs laser pulse is used to irradiate interline CCD solid-state image sensor in the experiment. In order to focus laser energy onto tiny CCD active cells, an optical system of F/5.6 is used. A Sony production CCDs are chose as typical targets. The damage threshold is evaluated with multiple test data. Point damage, line damage and full array damage were observed when the irradiated pulse energy continuously increase during the experiment. The point damage threshold is found 151.2 mJ/cm2.The line damage threshold is found 508.2 mJ/cm2.The full-array damage threshold is found to be 5.91 J/cm2. Although the phenomenon is almost the same as that of nano laser interaction with CCD, these damage thresholds are substantially lower than that of data obtained from nano second laser interaction with CCD. Then at the same time, the electric features after different degrees of damage are tested with electronic multi meter. The resistance values between clock signal lines are measured. Contrasting the resistance values of the CCD before and after damage, it is found that the resistances decrease significantly between the vertical transfer clock signal lines values. The same results are found between the vertical transfer clock signal line and the earth electrode (ground).At last, the damage position and the damage mechanism were analyzed with above results and SEM morphological experiments. The point damage results in the laser destroying material, which shows no macro electro influence. The line damage is quite different from that of point damage, which shows deeper material corroding effect. More importantly, short circuits are found between vertical clock lines. The full array damage is even more severe than that of line damage starring with SEM, while no obvious different electrical features than that of line damage are found. Further researches are anticipated in femto second laser caused CCD damage mechanism with more advanced tools. This research is valuable in EO countermeasure and/or laser shielding applications.

Line tension of a two dimensional gas-liquid interface.

PubMed

Santra, Mantu; Bagchi, Biman

2009-08-28

In two dimensional (2D) gas-liquid systems, the reported simulation values of line tension are known to disagree with the existing theoretical estimates. We find that while the simulation erred in truncating the range of the interaction potential, and as a result grossly underestimated the actual value, the earlier theoretical calculation was also limited by several approximations. When both the simulation and the theory are improved, we find that the estimate of line tension is in better agreement with each other. The small value of surface tension suggests increased influence of noncircular clusters in 2D gas-liquid nucleation, as indeed observed in a recent simulation.

TS and ERCC-1 mRNA expressions and clinical outcome in patients with metastatic colon cancer in CONFIRM-1 and -2 clinical trials.

PubMed

Grimminger, P P; Shi, M; Barrett, C; Lebwohl, D; Danenberg, K D; Brabender, J; Vigen, C L P; Danenberg, P V; Winder, T; Lenz, H-J

2012-10-01

To validate established cutoff levels of thymidylate synthase (TS) and excision repair cross-complementing (ERCC-1) intratumoral mRNA expressions in tumor samples from metastatic colorectal cancer (mCRC) patients treated with PTK787/ZK222584 (PTK/ZK). From 122 samples of patients with mCRC enrolled in CONFIRM-1 (Colorectal Oral Novel Therapy for the Inhibition of Angiogenesis and Retarding of Metastases) or CONFIRM-2, mRNA was isolated of microdissected formalin-fixed paraffin-embedded samples and quantitated using TaqMan-based technology. Existing TS and ERCC-1 cutoff levels were tested for their prognostic value in first-line and second-line therapy. TS expression was associated with overall survival (OS) in first-line, but not second-line therapy. ERCC-1 was associated with OS in patients treated with first-line and second-line FOLFOX4. In first-line FOLFOX4, combination of high TS and/or high ERCC-1 was associated with shorter OS. A correlation was observed between ERCC-1 expression and benefit from PTK/ZK+FOLFOX4 treatment. TS and ERCC-1 expression is associated with clinical outcome in mCRC. Baseline TS and ERCC-1 levels may allow the selection of patients who benefit from FOLFOX4 chemotherapy.

High-resolution room temperature and jet-cooled spectroscopic investigation of 15NH3 in the ν1+ν3 band region (1.51 μm)

NASA Astrophysics Data System (ADS)

Földes, T.; Vanfleteren, T.; Rizopoulos, A.; Herman, M.; Vander Auwera, J.; Softley, T. P.; Di Lonardo, G.; Fusina, L.

2016-08-01

Spectra of 99% isotopically pure 15NH3 were recorded using cavity ring-down (CRD, 6567-6639 cm-1) and Fourier transform (FT, 6350-6985 cm-1) spectroscopy under jet cooled and room temperature conditions, respectively. Measured line positions on both data sets improve on literature values, in particular by one order of magnitude for the ν1+ν3 band. A room temperature list of line positions, with approximate line intensities, is provided, much more complete and precise than presently available. Line broadening effects in the CRD spectrum allowed lines with J‧‧‧- values between 0 and 3 to be identified. Ground state combination differences were used to refine the assignments, further assisted by intensity ratios between the two data sets. Reliable values for J, K and inversion symmetry of the ground state vibrational levels, as well as further information on a/s doublets could be obtained, updating and extending literature assignments.

Antiproliferative Activity of Xanthones Isolated from Artocarpus obtusus

PubMed Central

Hashim, Najihah Mohd; Rahmani, Mawardi; Ee, Gwendoline Cheng Lian; Sukari, Mohd Aspollah; Yahayu, Maizatulakmal; Oktima, Winda; Ali, Abd Manaf; Go, Rusea

2012-01-01

An investigation of the chemical constituents in Artocarpus obtusus species led to the isolation of three new xanthones, pyranocycloartobiloxanthone A (1), dihydroartoindonesianin C (2), and pyranocycloartobiloxanthone B (3). The compounds were subjected to antiproliferative assay against human promyelocytic leukemia (HL60), human chronic myeloid leukemia (K562), and human estrogen receptor (ER+) positive breast cancer (MCF7) cell lines. Pyranocycloartobiloxanthone A (1) consistently showed strong cytotoxic activity against the three cell lines compared to the other two with IC50 values of 0.5, 2.0 and 5.0 μg/mL, respectively. Compound (1) was also observed to exert antiproliferative activity and apoptotic promoter towards HL60 and MCF7 cell lines at respective IC50 values. The compound (1) was not toxic towards normal cell lines human nontumorigenic breast cell line (MCF10A) and human peripheral blood mononuclear cells (PBMCs) with IC50 values of more than 30 μg/mL. PMID:21960741

Virtual Sensors for On-line Wheel Wear and Part Roughness Measurement in the Grinding Process

PubMed Central

Arriandiaga, Ander; Portillo, Eva; Sánchez, Jose A.; Cabanes, Itziar; Pombo, Iñigo

2014-01-01

Grinding is an advanced machining process for the manufacturing of valuable complex and accurate parts for high added value sectors such as aerospace, wind generation, etc. Due to the extremely severe conditions inside grinding machines, critical process variables such as part surface finish or grinding wheel wear cannot be easily and cheaply measured on-line. In this paper a virtual sensor for on-line monitoring of those variables is presented. The sensor is based on the modelling ability of Artificial Neural Networks (ANNs) for stochastic and non-linear processes such as grinding; the selected architecture is the Layer-Recurrent neural network. The sensor makes use of the relation between the variables to be measured and power consumption in the wheel spindle, which can be easily measured. A sensor calibration methodology is presented, and the levels of error that can be expected are discussed. Validation of the new sensor is carried out by comparing the sensor's results with actual measurements carried out in an industrial grinding machine. Results show excellent estimation performance for both wheel wear and surface roughness. In the case of wheel wear, the absolute error is within the range of microns (average value 32 μm). In the case of surface finish, the absolute error is well below Ra 1 μm (average value 0.32 μm). The present approach can be easily generalized to other grinding operations. PMID:24854055

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heng, Kevin, E-mail: kevin.heng@csh.unibe.ch

We present a dimensionless index that quantifies the degree of cloudiness of the atmosphere of a transiting exoplanet. Our cloudiness index is based on measuring the transit radii associated with the line center and wing of the sodium or potassium line. In deriving this index, we revisited the algebraic formulae for inferring the isothermal pressure scale height from transit measurements. We demonstrate that the formulae of Lecavelier et al. and Benneke and Seager are identical: the former is inferring the temperature while assuming a value for the mean molecular mass and the latter is inferring the mean molecular mass whilemore » assuming a value for the temperature. More importantly, these formulae cannot be used to distinguish between cloudy and cloud-free atmospheres. We derive values of our cloudiness index for a small sample of seven hot Saturns/Jupiters taken from Sing et al. We show that WASP-17b, WASP-31b, and HAT-P-1b are nearly cloud-free at visible wavelengths. We find the tentative trend that more irradiated atmospheres tend to have fewer clouds consisting of sub-micron-sized particles. We also derive absolute sodium and/or potassium abundances ∼10{sup 2} cm{sup −3} for WASP-17b, WASP-31b, and HAT-P-1b (and upper limits for the other objects). Higher-resolution measurements of both the sodium and potassium lines, for a larger sample of exoplanetary atmospheres, are needed to confirm or refute this trend.« less

Synthesis of sulfadimethoxine based surfactants and their evaluation as antitumor agents.

PubMed

Khowdiary, Manal Mohmed; Mostafa, Nashwa S

2016-01-01

Synthesized CO (II) and Pt (II) of sulfadimethoxine. These compounds were tested for potential antitumor activity against two of human tumor cell lines, colon carcinoma cell line [Hct116], and breast carcinoma cell line MCF7. The structures of the resulting compounds have been investigated by elemental, FT-IR and H 1 NMR analyzes to insure the purity and confirmed the structures of them. The surface properties studies and octanol/water partition coefficients, Po/w were measured. The synthesized compounds exhibit biological activities with the lowest log Po/w and critical micelle concentration (CMC) values. In addition, in this article we provide an insight into this subject in order to increase the drug bioavailability. Inhibitory activity against colon carcinoma cells was detected for Pt and cobalt ion complex with IC50 = 4.5, 2.2 µg and against breast carcinoma cells IC50 = 18.2, 5.7 µg, respectively. The main goal of cancer therapy is to attain the maximum therapeutic damage of tumor cells in combination with a minimum concentration of the drug. This can be achieved in principle via selective antitumor preparations, the cytostatic effects of which would be restricted within tumor tissue. While 100% selectivity may be impractical, the achievement of reasonably high selectivity seems to be a feasible aim. Platinum and cobalt complex surfactants in our research affect tumor tissue at a very low concentration at values lower than their CMC values; this indicate that the sulfadimethoxine complexes merit further investigation as potential antitumor drugs.

An exploratory case study of the impact of expanding cost-effectiveness analysis for second-line nivolumab for patients with squamous non-small cell lung cancer in Canada: Does it make a difference?

PubMed

Shafrin, Jason; Skornicki, Michelle; Brauer, Michelle; Villeneuve, Julie; Lees, Michael; Hertel, Nadine; Penrod, John R; Jansen, Jeroen

2018-04-26

Health technology appraisal agencies often rely on cost-effectiveness analyses to inform coverage decisions for new treatments. These assessments, however, frequently measure a treatment's value from the payer's perspective, and may not capture value generated from reduced caregiving costs, increased productivity, value based on patient risk preferences, option value or the insurance value to non-patients. To examine how using a broader societal perspective of treatment value affects cost-effectiveness estimates, this case study analyzed the net monetary benefit (NMB) of second-line nivolumab treatment of patients with squamous non-small cell lung cancer (NSCLC) in Canada. The comparator was treatment with docetaxel. NMB was measured from three perspectives: (i) traditional payer, (ii) traditional societal and (iii) broad societal. Nivolumab was more effective (increased quality-adjusted life years by 0.66 versus docetaxel), but also increased costs by $100,168 CAD. When valuing a quality-adjusted life year at $150,000, the net monetary benefit from the payer perspective suggested that costs modestly exceed benefits (NMB: -$1031). Adopting a societal perspective, however, nivolumab's benefits outweighed its costs (NMB: +$6752 and +$91,084 from the traditional and broad societal perspectives, respectively). Broadening cost-effectiveness analysis beyond the traditional payer perspective had a significant impact on the result and should be considered in order to capture all treatment benefits and costs of societal relevance. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

EVIDENCE FOR ENHANCED {sup 3}HE IN FLARE-ACCELERATED PARTICLES BASED ON NEW CALCULATIONS OF THE GAMMA-RAY LINE SPECTRUM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, R. J.; Kozlovsky, B.; Share, G. H., E-mail: murphy@ssd5.nrl.navy.mil, E-mail: benz@wise.tau.ac.il, E-mail: share@astro.umd.edu

2016-12-20

The {sup 3}He abundance in impulsive solar energetic particle (SEP) events is enhanced up to several orders of magnitude compared to its photospheric value of [{sup 3}He]/[{sup 4}He] = 1–3 × 10{sup −4}. Interplanetary magnetic field and timing observations suggest that these events are related to solar flares. Observations of {sup 3}He in flare-accelerated ions would clarify the relationship between these two phenomena. Energetic {sup 3}He interactions in the solar atmosphere produce gamma-ray nuclear-deexcitation lines, both lines that are also produced by protons and α particles and lines that are essentially unique to {sup 3}He. Gamma-ray spectroscopy can, therefore, reveal enhanced levelsmore » of accelerated {sup 3}He. In this paper, we identify all significant deexcitation lines produced by {sup 3}He interactions in the solar atmosphere. We evaluate their production cross sections and incorporate them into our nuclear deexcitation-line code. We find that enhanced {sup 3}He can affect the entire gamma-ray spectrum. We identify gamma-ray line features for which the yield ratios depend dramatically on the {sup 3}He abundance. We determine the accelerated {sup 3}He/ α ratio by comparing these ratios with flux ratios measured previously from the gamma-ray spectrum obtained by summing the 19 strongest flares observed with the Solar Maximum Mission Gamma-Ray Spectrometer. All six flux ratios investigated show enhanced {sup 3}He, confirming earlier suggestions. The {sup 3}He/ α weighted mean of these new measurements ranges from 0.05 to 0.3 (depending on the assumed accelerated α /proton ratio) and has a <1 × 10{sup −3} probability of being consistent with the photospheric value. With the improved code, we can now exploit the full potential of gamma-ray spectroscopy to establish the relationship between flare-accelerated ions and {sup 3}He-rich SEPs.« less

Theory and application of laser ultrasonic shear wave birefringence measurements to the determination of microstructure orientation in transversely isotropic, polycrystalline graphite materials

DOE PAGES

Zeng, Fan W.; Contescu, Cristian I.; Gallego, Nidia C.; ...

2016-12-18

Laser ultrasonic line source methods have been used to study elastic anisotropy in nuclear graphites by measuring shear wave birefringence. Depending on the manufacturing processes used during production, nuclear graphites can exhibit various degrees of material anisotropy related to preferred crystallite orientation and to microcracking. In this paper, laser ultrasonic line source measurements of shear wave birefringence on NBG-25 have been performed to assess elastic anisotropy. Laser line sources allow specific polarizations for shear waves to be transmitted – the corresponding wavespeeds can be used to compute bulk, elastic moduli that serve to quantify anisotropy. These modulus values can bemore » interpreted using physical property models based on orientation distribution coefficients and microcrack-modified, single crystal moduli to represent the combined effects of crystallite orientation and microcracking on material anisotropy. Finally, ultrasonic results are compared to and contrasted with measurements of anisotropy based on the coefficient of thermal expansion to show the relationship of results from these techniques.« less

Detection of atmospheric velocity fields in A-type stars

NASA Astrophysics Data System (ADS)

Landstreet, J. D.

1998-10-01

High signal-to-noise spectra with spectral resolution of more than 10(5) have been obtained of one normal B9.5V, one normal A1V, two Am stars, and two HgMn B stars having v sin i less than 6 km s(-1) . These spectra are modeled with LTE line profile synthesis to test the extent to which the spectrum of each star can be modeled correctly with a single set of parameters T_e, log g, chemical abundances, v sin i, and (depth-independent) microturbulent velocity xi . The answer to this question is important for abundance analysis of A and B stars; if conventional line synthesis does not reproduce the line profiles observed in stars of small v sin i, results obtained from such analysis are not likely to be very precise. The comparison of models with observations is then used to search for direct evidence of atmospheric motions, including line-strength dependent broadening, line core shape, and line asymmetries, in order to study how the microturbulence derived from abundance analysis is related to more direct evidence of atmospheric velocity fields. It is found for the three stars with 12,000 >= T_e >= 10,200 K (the normal star 21 Peg and the two HgMn stars 53 Tau and HD 193452) that xi is less than 1 km s(-1) , and line profiles are reproduced accurately by the synthesis with a single set of parameters. The slightly cooler (T_e ~ 9800 K) star HD 72660 has only a slightly stronger surface convective layer than the hotter stars, but for this star xi ~ 2.2 km s(-1) . Strong spectral lines all show significant asymmetry, with the blue line wing deeper than the red wing, and have line bisectors which have curvature towards the blue with a span of about 0.5 to 1.0 km s(-1) . A single model fits all lines satisfactorily. The two Am stars (HD 108642 and 32 Aqr), with T_e ~ 8000 K, are found to have much larger values of xi (4 to 5 km s(-1) ). The strong spectral lines of these two stars are extremely asymmetric, with depressed blue wings, and the bisectors have spans of order 3 km s(-1) . No consistent fit to all lines can be found with a single model of the type used here. It is concluded (a) that classical LTE line synthesis is able to reproduce with considerable accuracy the line profiles of late B and early A stars with T_e above about 9500 K, but that the LTE model with depth-independent microturbulence provides a very poor approximation for cooler A stars, (b) that curve-of-growth microturbulent velocities in A stars are related to directly detectable atmospheric velocity fields, and (c) that the discrepancies between calculated and observed line profiles in stars with temperatures in the vicinity of 8000 K are so large that abundances derived mainly from saturated lines may well contain significant errors. As a by-product, laboratory gf values for Fe II between 3800 and 5300 Angstroms have been combined to form a set of data optimized for internal consistency of the gf values. Based on observations obtained with the Canada-France-Hawaii telescope, operated by the National Research Council of Canada, the Centre National de Recherche Scientifique of France, and the University of Hawaii, and with the 1.52-m telescope of the Observatoire de Haute Provence, operated by the Centre National de Recherche Scientifique of France.

Accuracy of epidemiological inferences based on publicly available information: retrospective comparative analysis of line lists of human cases infected with influenza A(H7N9) in China

PubMed Central

2014-01-01

Background Appropriate public health responses to infectious disease threats should be based on best-available evidence, which requires timely reliable data for appropriate analysis. During the early stages of epidemics, analysis of ‘line lists’ with detailed information on laboratory-confirmed cases can provide important insights into the epidemiology of a specific disease. The objective of the present study was to investigate the extent to which reliable epidemiologic inferences could be made from publicly-available epidemiologic data of human infection with influenza A(H7N9) virus. Methods We collated and compared six different line lists of laboratory-confirmed human cases of influenza A(H7N9) virus infection in the 2013 outbreak in China, including the official line list constructed by the Chinese Center for Disease Control and Prevention plus five other line lists by HealthMap, Virginia Tech, Bloomberg News, the University of Hong Kong and FluTrackers, based on publicly-available information. We characterized clinical severity and transmissibility of the outbreak, using line lists available at specific dates to estimate epidemiologic parameters, to replicate real-time inferences on the hospitalization fatality risk, and the impact of live poultry market closure. Results Demographic information was mostly complete (less than 10% missing for all variables) in different line lists, but there were more missing data on dates of hospitalization, discharge and health status (more than 10% missing for each variable). The estimated onset to hospitalization distributions were similar (median ranged from 4.6 to 5.6 days) for all line lists. Hospital fatality risk was consistently around 20% in the early phase of the epidemic for all line lists and approached the final estimate of 35% afterwards for the official line list only. Most of the line lists estimated >90% reduction in incidence rates after live poultry market closures in Shanghai, Nanjing and Hangzhou. Conclusions We demonstrated that analysis of publicly-available data on H7N9 permitted reliable assessment of transmissibility and geographical dispersion, while assessment of clinical severity was less straightforward. Our results highlight the potential value in constructing a minimum dataset with standardized format and definition, and regular updates of patient status. Such an approach could be particularly useful for diseases that spread across multiple countries. PMID:24885692

Accuracy of epidemiological inferences based on publicly available information: retrospective comparative analysis of line lists of human cases infected with influenza A(H7N9) in China.

PubMed

Lau, Eric H Y; Zheng, Jiandong; Tsang, Tim K; Liao, Qiaohong; Lewis, Bryan; Brownstein, John S; Sanders, Sharon; Wong, Jessica Y; Mekaru, Sumiko R; Rivers, Caitlin; Wu, Peng; Jiang, Hui; Li, Yu; Yu, Jianxing; Zhang, Qian; Chang, Zhaorui; Liu, Fengfeng; Peng, Zhibin; Leung, Gabriel M; Feng, Luzhao; Cowling, Benjamin J; Yu, Hongjie

2014-05-28

Appropriate public health responses to infectious disease threats should be based on best-available evidence, which requires timely reliable data for appropriate analysis. During the early stages of epidemics, analysis of 'line lists' with detailed information on laboratory-confirmed cases can provide important insights into the epidemiology of a specific disease. The objective of the present study was to investigate the extent to which reliable epidemiologic inferences could be made from publicly-available epidemiologic data of human infection with influenza A(H7N9) virus. We collated and compared six different line lists of laboratory-confirmed human cases of influenza A(H7N9) virus infection in the 2013 outbreak in China, including the official line list constructed by the Chinese Center for Disease Control and Prevention plus five other line lists by HealthMap, Virginia Tech, Bloomberg News, the University of Hong Kong and FluTrackers, based on publicly-available information. We characterized clinical severity and transmissibility of the outbreak, using line lists available at specific dates to estimate epidemiologic parameters, to replicate real-time inferences on the hospitalization fatality risk, and the impact of live poultry market closure. Demographic information was mostly complete (less than 10% missing for all variables) in different line lists, but there were more missing data on dates of hospitalization, discharge and health status (more than 10% missing for each variable). The estimated onset to hospitalization distributions were similar (median ranged from 4.6 to 5.6 days) for all line lists. Hospital fatality risk was consistently around 20% in the early phase of the epidemic for all line lists and approached the final estimate of 35% afterwards for the official line list only. Most of the line lists estimated >90% reduction in incidence rates after live poultry market closures in Shanghai, Nanjing and Hangzhou. We demonstrated that analysis of publicly-available data on H7N9 permitted reliable assessment of transmissibility and geographical dispersion, while assessment of clinical severity was less straightforward. Our results highlight the potential value in constructing a minimum dataset with standardized format and definition, and regular updates of patient status. Such an approach could be particularly useful for diseases that spread across multiple countries.

HYPERFINE-DEPENDENT gf-VALUES OF Mn I LINES IN THE 1.49-1.80 μm H BAND

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson, M.; Hutton, R.; Zou, Y.

2015-01-01

The three Mn I lines at 17325, 17339, and 17349 Å are among the 25 strongest lines (log (gf) > 0.5) in the H band. They are all heavily broadened due to hyperfine structure, and the profiles of these lines have so far not been understood. Earlier studies of these lines even suggested that they were blended. In this work, the profiles of these three infrared (IR) lines have been studied theoretically and compared to experimental spectra to assist in the complete understanding of the solar spectrum in the IR. It is shown that the structure of these lines cannot be describedmore » in the conventional way using the diagonal A and B hyperfine interaction constants. The off-diagonal hyperfine interaction not only has a large impact on the energies of the hyperfine levels, but also introduces a large intensity redistribution among the hyperfine lines, changing the line profiles dramatically. By performing large-scale calculations of the diagonal and off-diagonal hyperfine interaction and the gf-values between the upper and lower hyperfine levels and using a semi-empirical fitting procedure, we achieved agreement between our synthetic and experimental spectra. Furthermore, we compare our results with observations of stellar spectra. The spectra of the Sun and the K1.5 III red giant star Arcturus were modeled in the relevant region, 1.73-1.74 μm, using our theoretically predicted gf-values and energies for each individual hyperfine line. Satisfactory fits were obtained and clear improvements were found using our new data compared with the old available Mn I data. A complete list of energies and gf-values for all the 3d {sup 5}4s({sup 7} S)4d e{sup 6}D - 3d {sup 5}4s({sup 7} S)4f w{sup 6}F hyperfine lines are available as supporting material, whereas only the stronger lines are presented and discussed in detail in this paper.« less

Assessment of Antero-Posterior Skeletal and Soft Tissue Relationships of Adult Indian Subjects in Natural Head Position and Centric Relation

PubMed Central

Latif, Vishnu Ben; Keshavaraj; Rai, Rohan; Hegde, Gautham; Shajahan, Shabna

2015-01-01

Background: The aim of this study was to verify the intra-individual reproducibility of natural head position (NHP) in centric relation (CR) position, to prove the inter-individual differences in the Frankfort horizontal plane and sella-nasion line compared with the true horizontal line, and to establish linear norms from A-point, B-point, Pog as well as soft tissue A-point, soft tissue B-point, and soft tissue Pog to nasion true vertical line (NTVL) in adult Indian subjects. Methods: Lateral cephalograms (T1) of Angle’s Class I subjects were taken in NHP and with bite in CR. A second lateral cephalogram (T2) of these subjects with ANB angle in the range 1-4° were taken after 1 week using the same wax bite and both the radiographs were analyzed based on six angular parameters using cephalometric software (Do-it, Dental studio NX version 4.1) to assess the reproducibility of NHP. Linear values of six landmarks were taken in relation to NTVL, and the mean values were calculated. A total of 116 subjects were included in this study. Results: When the cephalometric values of T1 and T2 were analyzed, it was found that, the parameters showed a P < 0.001, indicating the reproducibility of NHP in CR. Mean values for point A, point B, Pog and their soft tissue counterparts were also obtained. Conclusion: The study proved that NHP is a reproducible and accurate when recorded with the mandible in CR. Linear norms for skeletal Class I subjects in relation to NTVL were established. PMID:26124598

Randomness fault detection system

NASA Technical Reports Server (NTRS)

Russell, B. Don (Inventor); Aucoin, B. Michael (Inventor); Benner, Carl L. (Inventor)

1996-01-01

A method and apparatus are provided for detecting a fault on a power line carrying a line parameter such as a load current. The apparatus monitors and analyzes the load current to obtain an energy value. The energy value is compared to a threshold value stored in a buffer. If the energy value is greater than the threshold value a counter is incremented. If the energy value is greater than a high value threshold or less than a low value threshold then a second counter is incremented. If the difference between two subsequent energy values is greater than a constant then a third counter is incremented. A fault signal is issued if the counter is greater than a counter limit value and either the second counter is greater than a second limit value or the third counter is greater than a third limit value.

An Algorithm for Critical Nodes Problem in Social Networks Based on Owen Value

PubMed Central

Wang, Xue-Guang

2014-01-01

Discovering critical nodes in social networks has many important applications. For finding out the critical nodes and considering the widespread community structure in social networks, we obtain each node's marginal contribution by Owen value. And then we can give a method for the solution of the critical node problem. We validate the feasibility and effectiveness of our method on two synthetic datasets and six real datasets. At the same time, the result obtained by using our method to analyze the terrorist network is in line with the actual situation. PMID:25006592

Assessment of biological effectiveness of boron neutron capture therapy in primary and metastatic melanoma cell lines.

PubMed

Rossini, Andrés E; Dagrosa, Maria A; Portu, Agustina; Saint Martin, Giselle; Thorp, Silvia; Casal, Mariana; Navarro, Aimé; Juvenal, Guillermo J; Pisarev, Mario A

2015-01-01

In order to optimize the effectiveness of Boron Neutron Capture Therapy (BNCT), Relative Biological Effectiveness (RBE) and Compound Biological Effectiveness (CBE) were determined in two human melanoma cell lines, M8 and Mel-J cells, using the amino acid p-boronophenylalanine (BPA) as boron carrier. The effects of BNCT on the primary amelanotic cell line M8 and on the metastatic pigmented melanoma cell line Mel-J were studied using colony formation assay. The RBE values were determined using both a gamma ray source, and the neutron beam from the Nuclear Reactor of the National Atomic Energy Commission (RA-3). For the determination of the RBE, cells were irradiated with increasing doses of both sources, between 1 and 8 Gy; and for the determination of CBE factors, the cells were pre-incubated with BPA before irradiation. Afterwards, the cell surviving fraction (SF) was determined for each treatment. Marked differences were observed between both cell lines. Mel-J cells were more radioresistant than the M8 cell line. The clonogenic assays showed that for a SF of 1%, the RBE values were 1.3 for M8 cells and 1.5 for Mel-J cells. Similarly, the CBE values for a 1% SF were 2.1 for M8 and 3 for Mel-J cell lines. For the endpoint of 0.1% of SF the RBE values obtained were 1.2 for M8 and 1.4 for Mel-J cells. Finally, CBE values calculated for a 0.1% were 2 and 2.6 for M8 and Mel-J cell lines respectively. In order to estimate the uptake of the non-radioactive isotope Boron 10 ((10)B), a neutron induced autoradiographic technique was performed showing discrepancies in (10)B uptake between both cell lines. These obtained in vitro results are the first effectiveness factors determined for human melanoma at the RA-3 nuclear reactor and show that BNCT dosimetry planning for patients could be successfully performed using these new factors.

The effects of stage-specific selection on the development of benzimidazole resistance in Haemonchus contortus in sheep.

PubMed

Taylor, M A; Hunt, K R; Goodyear, K L

2002-10-16

Resistance to the benzimidazole (BDZ) class of anthelmintics in nematodes of sheep has become a common and global phenomenon. The rate at which the selection process and development of resistance occurs is influenced by a number of factors. Of these, the effects of stage-specific exposures to anthelmintic were investigated with a BDZ-resistant strain of Haemonchus contortus (HCR) over five parasite generations. Sheep were infected at each generation with the HCR strain and were treated with thiabendazole (TBZ), either 5 days post-infection (p.i.) (larval line), 21 days p.i. (adult line), or left untreated (no selection line). Additionally eggs from each generation were exposed to TBZ (egg line). Geometric worm burdens were calculated from post-mortem worm counts, both at the start of the study, and after the final selection studies for each of the selection lines. Egg hatch assays (EHAs) were also conducted throughout the study. All data relating to worm burdens and EHAs for each generation were analysed by linear regression to produce dose titration curves and lethal dose(50) (LD(50)) values for each of the selection lines. Over the five generations, LD(50) values on dose-response were increased and worm survival occurred at higher dose rates of TBZ irrespective of the parasite stage exposed to treatment. A similar picture was seen with ED(50) values, which showed a fluctuating but generally upward trend for each of the three selection lines. In contrast, LD(50) and ED(50) values were decreased in the no selection line, indicating some degree of reversion albeit to levels still considered to be BDZ-resistant.

Line Positions of Centrifugal Distorsion Induced Rotational Transitions of Methane Measured up to 2.6 Thz at Sub-Mhz Accuracy with a Cw-Thz Photomixing Spectrometer

NASA Astrophysics Data System (ADS)

Bray, Cédric; Cuisset, Arnaud; Hindle, Francis; Mouret, Gaël; Bocquet, Robin; Boudon, Vincent

2017-06-01

Several Doppler limited rotational transitions of methane induced by centrifugal distortion have been measured with an unprecedented frequency accuracy using the THz photomixing synthesizer based on a frequency comb. Compared to previous synchrotron based FT-Far-IR measurements of Boudon et al., the accuracy of the line frequency measurements is improved by one order of magnitude, this yields a corresponding increase of two orders of magnitude to the weighting of these transitions in the global fit. The rotational transitions in the ν_4←ν_4 hot band are measured for the first time by the broad spectral coverage of the photomixing CW-THz spectrometer providing access up to R(5) transitions at 2.6 THz. The new global fit including the present lines has been used to update the methane line list of the HITRAN database. Some small, but significant variations of the parameter values are observed and are accompanied by a reduction of the 1-σ uncertainties on the rotational (B_0) and centrifugal distortion (D_0) constants. V. Boudon, O. Pirali, P. Roy, J.-B. Brubach, L. Manceron, J. Vander Auwera, J. Quant. Spectrosc. Radiat. Transfer, 111, 1117-1129 (2010).

Line Profile of H Lyman-Beta Emission from Dissociative Excitation of H2

NASA Technical Reports Server (NTRS)

Ajello, Joseph M.; Ahmed, Syed M.; Liu, Xian-Ming

1996-01-01

A high-resolution ultraviolet spectrometer was employed for a measurement of the H Lyman-Beta(H L(sub Beta)) emission Doppler line profile at 1025.7 A from dissociative excitation of H2 by electron impact. Analysis of the deconvolved line profile reveals the existence of a narrow central peak, less than 30 mA full width at half maximum (FWHM), and a broad pedestal base about 260 mA FWHM. Analysis of the red wing of the line profile is complicated by a group of Wemer and Lyman rotational lines 160-220 mA from the line center. Analysis of the blue wing of the line profile gives the kinetic-energy distribution. There are two main kinetic-energy components to the H(3p) distribution: (1) a slow distribution with a peak value near 0 eV from singly excited states, and (2) a fast distribution with a peak contribution near 7 eV from doubly excited states. Using two different techniques, the absolute cross section of H L(sub Beta)p is found to be 3.2+/-.8 x 10(exp -19)sq cm at 100-eV electron impact energy. The experimental cross-section and line-profile results can be compared to previous studies of H(alpha) (6563.7 A) for principal quantum number n=3 and L(sub alpha)(1215.7 A) for n=2.

CA II K-line metallicity indicator for field RR Lyrae stars

NASA Astrophysics Data System (ADS)

Clementini, Gisella; Tosi, Monica; Merighi, Roberto

In order to check and, possibly, improve the Preston's Delta S calibration scale, CCD spectra have been obtained for 25 field RR Lyrae variables. Eleven of the program stars have values of (Fe/H) derived by Butler and Deming (1979) from the Fe II lines' strength. For them we find that the equivalent width of the Ca II K line is extremely well correlated to the (Fe/H) values, the best fit relation being: (Fe/H) = 0.43W(K) - 2.75 where W(K) is the equivalent width of the K line. We conclude that the use of the K line equivalent width is at present the best method to derive the (Fe/H) abundance of the RR Lyrae stars.

Silicon X-ray line emission from solar flares and active regions

NASA Technical Reports Server (NTRS)

Parkinson, J. H.; Wolff, R. S.; Kestenbaum, H. L.; Ku, W. H.-M.; Lemen, J. R.; Long, K. S.; Novick, R.; Suozzo, R. J.; Weisskopf, M. C.

1978-01-01

New observations of solar flare and active region X-ray spectra obtained with the Columbia University instrument on OSO-8 are presented and discussed. The high sensitivity of the graphite crystal panel has allowed both line and continuum spectra to be served with moderate spectral resolution. Observations with higher spectral resolution have been made with a panel of pentaerythritol crystals. Twenty-nine lines between 1.5 and 7.0 A have been resolved and identified, including several dielectronic recombination satellite lines to Si XIV and Si XIII lines which have been observed for the first time. It has been found that thermal continuum models specified by single values of temperature and emission measure have fitted the data adequately, there being good agreement with the values of these parameters derived from line intensity ratios.

Line Mixing in Water Vapor and Methane

NASA Technical Reports Server (NTRS)

Smith, M. A. H.; Brown, L. R.; Toth, R. A.; Devi, V. Malathy; Benner, Chris

2006-01-01

A multispectrum fitting algorithm has been used to identify line mixing and determine mixing parameters for infrared transitions of H2O and CH4 in the 5-9 micrometer region. Line mixing parameters at room temperature were determined for two pairs of transitions in the v2 fundamental band of H2O-16, for self-broadening and for broadening by H2, He, CO2, N2, O2 and air. Line mixing parameters have been determined from air-broadened CH4 spectra, recorded at temperatures between 210 K and 314 K, in selected R-branch manifolds of the v4 band. For both H2O and CH4, the inclusion of line mixing was seen to have a greater effect on the retrieved values of the line shifts than on the retrieved values of other parameters

Slots in dielectric image line as mode launchers and circuit elements

NASA Astrophysics Data System (ADS)

Solbach, K.

1981-01-01

A planar resonator model is used to investigate slots in the ground plane of dielectric image lines. An equivalent circuit representation of the slot discontinuity is obtained, and the launching efficiency of the slot as a mode launcher is analyzed. Slots are also shown to be useful in the realization of dielectric image line array antennas. It is found that the slot discontinuity can be shown as a T-junction of the dielectric image line and a metal waveguide. The launching efficiency is found to increase with the dielectric constant of the dielectric image line, exhibiting a maximum value for guides whose height is slightly less than half a wavelength in the dielectric medium. The measured launching efficiencies of low permittivity dielectric image lines are found to be in good agreement with calculated values

Estimation of the axis of a screw motion from noisy data--a new method based on Plücker lines.

PubMed

Kiat Teu, Koon; Kim, Wangdo

2006-01-01

The problems of estimating the motion and orientation parameters of a body segment from two n point-set patterns are analyzed using the Plücker coordinates of a line (Plücker lines). The aim is to find algorithms less complex than those in conventional use, and thus facilitating more accurate computation of the unknown parameters. All conventional techniques use point transformation to calculate the screw axis. In this paper, we present a novel technique that directly estimates the axis of a screw motion as a Plücker line. The Plücker line can be transformed via the dual-number coordinate transformation matrix. This method is compared with Schwartz and Rozumalski [2005. A new method for estimating joint parameters from motion data. Journal of Biomechanics 38, 107-116] in simulations of random measurement errors and systematic skin movements. Simulation results indicate that the methods based on Plücker lines (Plücker line method) are superior in terms of extremely good results in the determination of the screw axis direction and position as well as a concise derivation of mathematical statements. This investigation yielded practical results, which can be used to locate the axis of a screw motion in a noisy environment. Developing the dual transformation matrix (DTM) from noisy data and determining the screw axis from a given DTM is done in a manner analogous to that for handling simple rotations. A more robust approach to solve for the dual vector associated with DTM is also addressed by using the eigenvector and the singular value decomposition.

Cost-effectiveness of precision medicine in the fourth-line treatment of metastatic lung adenocarcinoma: An early decision analytic model of multiplex targeted sequencing.

PubMed

Doble, Brett; John, Thomas; Thomas, David; Fellowes, Andrew; Fox, Stephen; Lorgelly, Paula

2017-05-01

To identify parameters that drive the cost-effectiveness of precision medicine by comparing the use of multiplex targeted sequencing (MTS) to select targeted therapy based on tumour genomic profiles to either no further testing with chemotherapy or no further testing with best supportive care in the fourth-line treatment of metastatic lung adenocarcinoma. A combined decision tree and Markov model to compare costs, life-years, and quality-adjusted life-years over a ten-year time horizon from an Australian healthcare payer perspective. Data sources included the published literature and a population-based molecular cohort study (Cancer 2015). Uncertainty was assessed using deterministic sensitivity analyses and quantified by estimating expected value of perfect/partial perfect information. Uncertainty due to technological/scientific advancement was assessed through a number of plausible future scenario analyses. Point estimate incremental cost-effective ratios indicate that MTS is not cost-effective for selecting fourth-line treatment of metastatic lung adenocarcinoma. Lower mortality rates during testing and for true positive patients, lower health state utility values for progressive disease, and targeted therapy resulting in reductions in inpatient visits, however, all resulted in more favourable cost-effectiveness estimates for MTS. The expected value to decision makers of removing all current decision uncertainty was estimated to be between AUD 5,962,843 and AUD 13,196,451, indicating that additional research to reduce uncertainty may be a worthwhile investment. Plausible future scenarios analyses revealed limited improvements in cost-effectiveness under scenarios of improved test performance, decreased costs of testing/interpretation, and no biopsy costs/adverse events. Reductions in off-label targeted therapy costs, when considered together with the other scenarios did, however, indicate more favourable cost-effectiveness of MTS. As more clinical evidence is generated for MTS, the model developed should be revisited and cost-effectiveness re-estimated under different testing scenarios to further understand the value of precision medicine and its potential impact on the overall health budget. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

A Reliability Comparison of Classical and Stochastic Thickness Margin Approaches to Address Material Property Uncertainties for the Orion Heat Shield

NASA Technical Reports Server (NTRS)

Sepka, Steve; Vander Kam, Jeremy; McGuire, Kathy

2018-01-01

The Orion Thermal Protection System (TPS) margin process uses a root-sum-square approach with branches addressing trajectory, aerothermodynamics, and material response uncertainties in ablator thickness design. The material response branch applies a bond line temperature reduction between the Avcoat ablator and EA9394 adhesive by 60 C (108 F) from its peak allowed value of 260 C (500 F). This process is known as the Bond Line Temperature Material Margin (BTMM) and is intended to cover material property and performance uncertainties. The value of 60 C (108 F) is a constant, applied at any spacecraft body location and for any trajectory. By varying only material properties in a random (monte carlo) manner, the perl-based script mcCHAR is used to investigate the confidence interval provided by the BTMM. In particular, this study will look at various locations on the Orion heat shield forebody for a guided and an abort (ballistic) trajectory.

Ultraviolet interstellar lines in the spectrum of Pi Scorpii recorded at 2 kilometers per second resolution

NASA Technical Reports Server (NTRS)

Joseph, Charles L.; Jenkins, Edward B.

1991-01-01

A spectrum of Pi Scorpii has been recorded from 1003 to 1172 A with a maximum SNR of about 20 and a velocity resolution of 2.4 km/s. Three types of H I as well as two discrete H II regions are distinguished in velocity space, allowing independent analyses of physical conditions and abundances for the individual gas components. A direct evaluation of optical depths and column densities across the absorption features is applied for the first time to the dominant ionization stage of Fe, Si, and P. Based on an analysis of the spectrum, it is concluded that all of the Ti II absorption seen toward Pi Sco arises in the warm, neutral intercloud medium while the other elements have their maximum absorption associated with cold clouds. A conservative value of log delta less than -3.4 is inferred for the Ti depletion in the cold clouds, a value more extreme than any integrated, line-of-sight measurement made to date.

A rough set-based measurement model study on high-speed railway safety operation.

PubMed

Hu, Qizhou; Tan, Minjia; Lu, Huapu; Zhu, Yun

2018-01-01

Aiming to solve the safety problems of high-speed railway operation and management, one new method is urgently needed to construct on the basis of the rough set theory and the uncertainty measurement theory. The method should carefully consider every factor of high-speed railway operation that realizes the measurement indexes of its safety operation. After analyzing the factors that influence high-speed railway safety operation in detail, a rough measurement model is finally constructed to describe the operation process. Based on the above considerations, this paper redistricts the safety influence factors of high-speed railway operation as 16 measurement indexes which include staff index, vehicle index, equipment index and environment. And the paper also provides another reasonable and effective theoretical method to solve the safety problems of multiple attribute measurement in high-speed railway operation. As while as analyzing the operation data of 10 pivotal railway lines in China, this paper respectively uses the rough set-based measurement model and value function model (one model for calculating the safety value) for calculating the operation safety value. The calculation result shows that the curve of safety value with the proposed method has smaller error and greater stability than the value function method's, which verifies the feasibility and effectiveness.

On the Effective Construction of Compactly Supported Wavelets Satisfying Homogenous Boundary Conditions on the Interval

NASA Technical Reports Server (NTRS)

Chiavassa, G.; Liandrat, J.

1996-01-01

We construct compactly supported wavelet bases satisfying homogeneous boundary conditions on the interval (0,1). The maximum features of multiresolution analysis on the line are retained, including polynomial approximation and tree algorithms. The case of H(sub 0)(sup 1)(0, 1)is detailed, and numerical values, required for the implementation, are provided for the Neumann and Dirichlet boundary conditions.

Improved methods of AAV-mediated gene targeting for human cell lines using ribosome-skipping 2A peptide

PubMed Central

Karnan, Sivasundaram; Ota, Akinobu; Konishi, Yuko; Wahiduzzaman, Md; Hosokawa, Yoshitaka; Konishi, Hiroyuki

2016-01-01

The adeno-associated virus (AAV)-based targeting vector has been one of the tools commonly used for genome modification in human cell lines. It allows for relatively efficient gene targeting associated with 1–4-log higher ratios of homologous-to-random integration of targeting vectors (H/R ratios) than plasmid-based targeting vectors, without actively introducing DNA double-strand breaks. In this study, we sought to improve the efficiency of AAV-mediated gene targeting by introducing a 2A-based promoter-trap system into targeting constructs. We generated three distinct AAV-based targeting vectors carrying 2A for promoter trapping, each targeting a GFP-based reporter module incorporated into the genome, PIGA exon 6 or PIGA intron 5. The absolute gene targeting efficiencies and H/R ratios attained using these vectors were assessed in multiple human cell lines and compared with those attained using targeting vectors carrying internal ribosome entry site (IRES) for promoter trapping. We found that the use of 2A for promoter trapping increased absolute gene targeting efficiencies by 3.4–28-fold and H/R ratios by 2–5-fold compared to values obtained with IRES. In CRISPR-Cas9-assisted gene targeting using plasmid-based targeting vectors, the use of 2A did not enhance the H/R ratios but did upregulate the absolute gene targeting efficiencies compared to the use of IRES. PMID:26657635

Stark broadening parameters and transition probabilities of persistent lines of Tl II

NASA Astrophysics Data System (ADS)

de Andrés-García, I.; Colón, C.; Fernández-Martínez, F.

2018-05-01

The presence of singly ionized thallium in the stellar atmosphere of the chemically peculiar star χ Lupi was reported by Leckrone et al. in 1999 by analysis of its stellar spectrum obtained with the Goddard High Resolution Spectrograph (GHRS) on board the Hubble Space Telescope. Atomic data about the spectral line of 1307.50 Å and about the hyperfine components of the spectral lines of 1321.71 Å and 1908.64 Å were taken from different sources and used to analyse the isotopic abundance of thallium II in the star χ Lupi. From their results the authors concluded that the photosphere of the star presents an anomalous isotopic composition of Tl II. A study of the atomic parameters of Tl II and of the broadening by the Stark effect of its spectral lines (and therefore of the possible overlaps of these lines) can help to clarify the conclusions about the spectral abundance of Tl II in different stars. In this paper we present calculated values of the atomic transition probabilities and Stark broadening parameters for 49 spectral lines of Tl II obtained by using the Cowan code including core polarization effects and the Griem semiempirical approach. Theoretical values of radiative lifetimes for 11 levels (eight with experimental values in the bibliography) are calculated and compared with the experimental values in order to test the quality of our results. Theoretical trends of the Stark width and shift parameters versus the temperature for spectral lines of astrophysical interest are displayed. Trends of our calculated Stark width for the isoelectronic sequence Tl II-Pb III-Bi IV are also displayed.

Laboratory oscillator strengths of Sc i in the near-infrared region for astrophysical applications

NASA Astrophysics Data System (ADS)

Pehlivan, A.; Nilsson, H.; Hartman, H.

2015-10-01

Context. Atomic data is crucial for astrophysical investigations. To understand the formation and evolution of stars, we need to analyse their observed spectra. Analysing a spectrum of a star requires information about the properties of atomic lines, such as wavelengths and oscillator strengths. However, atomic data of some elements are scarce, particularly in the infrared region, and this paper is part of an effort to improve the situation on near-IR atomic data. Aims: This paper investigates the spectrum of neutral scandium, Sc I, from laboratory measurements and improves the atomic data of Sc I lines in the infrared region covering lines in R, I, J, and K bands. Especially, we focus on measuring oscillator strengths for Sc I lines connecting the levels with 4p and 4s configurations. Methods: We combined experimental branching fractions with radiative lifetimes from the literature to derive oscillator strengths (f-values). Intensity-calibrated spectra with high spectral resolution were recorded with Fourier transform spectrometer from a hollow cathode discharge lamp. The spectra were used to derive accurate oscillator strengths and wavelengths for Sc I lines, with emphasis on the infrared region. Results: This project provides the first set of experimental Sc I lines in the near-infrared region for accurate spectral analysis of astronomical objects. We derived 63 log(gf) values for the lines between 5300 Å and 24 300 Å. The uncertainties in the f-values vary from 5% to 20%. The small uncertainties in our values allow for an increased accuracy in astrophysical abundance determinations.

Robust visual object tracking with interleaved segmentation

NASA Astrophysics Data System (ADS)

Abel, Peter; Kieritz, Hilke; Becker, Stefan; Arens, Michael

2017-10-01

In this paper we present a new approach for tracking non-rigid, deformable objects by means of merging an on-line boosting-based tracker and a fast foreground background segmentation. We extend an on-line boosting- based tracker, which uses axes-aligned bounding boxes with fixed aspect-ratio as tracking states. By constructing a confidence map from the on-line boosting-based tracker and unifying this map with a confidence map, which is obtained from a foreground background segmentation algorithm, we build a superior confidence map. For constructing a rough confidence map of a new frame based on on-line boosting, we employ the responses of the strong classifier as well as the single weak classifier responses that were built before during the updating step. This confidence map provides a rough estimation of the object's position and dimension. In order to refine this confidence map, we build a fine, pixel-wisely segmented confidence map and merge both maps together. Our segmentation method is color-histogram-based and provides a fine and fast image segmentation. By means of back-projection and the Bayes' rule, we obtain a confidence value for every pixel. The rough and the fine confidence maps are merged together by building an adaptively weighted sum of both maps. The weights are obtained by utilizing the variances of both confidence maps. Further, we apply morphological operators in the merged confidence map in order to reduce the noise. In the resulting map we estimate the object localization and dimension via continuous adaptive mean shift. Our approach provides a rotated rectangle as tracking states, which enables a more precise description of non-rigid, deformable objects than axes-aligned bounding boxes. We evaluate our tracker on the visual object tracking (VOT) benchmark dataset 2016.

A roadmap for the implementation of mHealth innovations for image-based diagnostic support in clinical and public-health settings: a focus on front-line health workers and health-system organizations.

PubMed

Wallis, Lee; Hasselberg, Marie; Barkman, Catharina; Bogoch, Isaac; Broomhead, Sean; Dumont, Guy; Groenewald, Johann; Lundin, Johan; Norell Bergendahl, Johan; Nyasulu, Peter; Olofsson, Maud; Weinehall, Lars; Laflamme, Lucie

2017-06-01

Diagnostic support for clinicians is a domain of application of mHealth technologies with a slow uptake despite promising opportunities, such as image-based clinical support. The absence of a roadmap for the adoption and implementation of these types of applications is a further obstacle. This article provides the groundwork for a roadmap to implement image-based support for clinicians, focusing on how to overcome potential barriers affecting front-line users, the health-care organization and the technical system. A consensual approach was used during a two-day roundtable meeting gathering a convenience sample of stakeholders (n = 50) from clinical, research, policymaking and business fields and from different countries. A series of sessions was held including small group discussions followed by reports to the plenary. Session moderators synthesized the reports in a number of theme-specific strategies that were presented to the participants again at the end of the meeting for them to determine their individual priority. There were four to seven strategies derived from the thematic sessions. Once reviewed and prioritized by the participants some received greater priorities than others. As an example, of the seven strategies related to the front-line users, three received greater priority: the need for any system to significantly add value to the users; the usability of mHealth apps; and the goodness-of-fit into the work flow. Further, three aspects cut across the themes: ease of integration of the mHealth applications; solid ICT infrastructure and support network; and interoperability. Research and development in image-based diagnostic pave the way to making health care more accessible and more equitable. The successful implementation of those solutions will necessitate a seamless introduction into routines, adequate technical support and significant added value.

Effect of sealer coating and storage methods on the surface roughness of soft liners.

PubMed

Usta Kutlu, Ilknur; Yanikoğlu, Nuran Dinckal; Kul, Esra; Duymuş, Zeynep Yesïl; Sağsöz, Nurdan Polat

2016-03-01

A soft lining is applied under a removable prosthesis for various reasons. The porosity of the lining material may increase colonization by microorganisms and cause tissue inflammation. The purpose of this in vitro study was to evaluate the effect of sealer coating on the surface roughness of soft lining materials under 4 different conditions. A total of 125 specimens were prepared. One high-temperature silicone-based soft lining material and 2 room-temperature-polymerized soft lining materials (1 silicone-based and 1 methacrylate-based) were used. Twenty-five specimens of each room-temperature soft lining material were coated with 2 layers of surface sealer. Additionally, 5 specimens of each material were stored in either distilled water, Coca-Cola, denture cleanser, saliva, or air. The surface roughness was measured at baseline and after 1, 7, 14, and 28 days. Surface roughness values were analyzed with repeated measures analysis of variance, and the Bonferroni multiple comparison test was performed using time-dependent groups and storage methods. In the time-dependent groups, methacrylate-based sealer-coated soft liners exhibited a significant increase in roughness (1.74-2.09 μm, P<.001), and silicone-based sealer-coated soft liners exhibited a decrease in roughness, but it was not significant (2.16-2.02 μm, P>.05). Therefore, the sealer coating was not effective in reducing surface roughness. Among the time-dependent storage methods, the denture cleanser exhibited an almost significant increase in roughness (1.83-1.99 μm, P=.054). Coca-Cola and artificial saliva did not show a significant difference (P>.05). However, a significant decrease in roughness was found with distilled water (P=.02) and air (P<.001). Statistically significant differences in surface roughness were found among the different types of soft liners. The sealer coating had no significant effect, and denture cleanser slightly increased the surface roughness. Contrary to expectations, the roughness did not increase in all groups over time. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Consolidation of Soft Layers by Finite Strain Analysis.

DTIC Science & Technology

1982-03-01

compressible foundation or layer is divided into for computation purposes. NBL an integer denoting the following options: 1 = consolidation calculated for...i.e., NDATAI 1), the data file should be sequenced in the following manner: a. NST, NPROB, NDATA1, NDATA2 b. NST, NPT, NBL c. NST, GSBL, HBL, WLl, LBL...particular line types: Line type c: Q0 and DQ have nonzero values only if NBL = 3. If NBL = 2, all data values are set to zero except NST. Line type d: There

Valuation and handling of dialogue in leadership: a grounded theory study in Swedish hospitals.

PubMed

Grill, C; Ahlborg, G; Lindgren, E C

2011-01-01

Leadership can positively affect the work environment and health. Communication and dialogue are an important part in leadership. Studies of how dialogue is valued and handled in first-line leadership have not so far been found. The aim of this study is to develop a theoretical understanding of how first-line leaders at hospitals in western Sweden value and handle dialogue in the organisation. The study design was explorative and based on grounded theory. Data collection consisted of interviews and observations. A total of 11 first-line leaders at two hospitals in western Sweden were chosen as informants, and for four of them observation was also used. One core category emerged in the analysis: leaders' communicative actions, which could be strategically or understanding-oriented, and experienced as equal or unequal and performed equitably or inequitably, within a power relationship. Four different types of communicativeactions emerged: collaborative, nurturing, controlling, and confrontational. Leaders had strategies for creating arenas and relationships for dialogue, but dialogue could be constrained by external circumstances or ignorance of the frameworks needed to conduct and accomplish dialogue. First-line leaders should be offered guidance in understanding the consequences of consciously choosing and strengthening the communication component in leadership. The positive valuation of dialogue was not always manifest in practical action. One significant consequence of not using dialogue was that information with impact on organisational efficiency and finances was communicated upwards in the management system.

Product-line selection and pricing with remanufacturing under availability constraints

NASA Astrophysics Data System (ADS)

Aras, Necati; Esenduran, G.÷k.‡e.; Altinel, I. Kuban

2004-12-01

Product line selection and pricing are two crucial decisions for the profitability of a manufacturing firm. Remanufacturing, on the other hand, may be a profitable strategy that captures the remaining value in used products. In this paper we develop a mixed-integer nonlinear programming model form the perspective of an original equipment manufacturer (OEM). The objective of the OEM is to select products to manufacture and remanufacture among a set of given alternatives and simultaneously determine their prices so as to maximize its profit. It is assumed that the probability a customer selects a product is proportional to its utility and inversely proportional to its price. The utility of a product is an increasing function of its perceived quality. In our base model, products are discriminated by their unit production costs and utilities. We also analyze a case where remanufacturing is limited by the available quantity of collected remanufacturable products. We show that the resulting problem is decomposed into the pricing and product line selection subproblems. Pricing problem is solved by a variant of the simplex search procedure which can also handle constraints, while complete enumeration and a genetic algorithm are used for the solution of the product line selection problem. A number of experiments are carried out to identify conditions under which it is economically viable for the firm to sell remanufactured products. We also determine the optimal utility and unit production cost values of a remanufactured product, which maximizes the total profit of the OEM.

Brain vascular image segmentation based on fuzzy local information C-means clustering

NASA Astrophysics Data System (ADS)

Hu, Chaoen; Liu, Xia; Liang, Xiao; Hui, Hui; Yang, Xin; Tian, Jie

2017-02-01

Light sheet fluorescence microscopy (LSFM) is a powerful optical resolution fluorescence microscopy technique which enables to observe the mouse brain vascular network in cellular resolution. However, micro-vessel structures are intensity inhomogeneity in LSFM images, which make an inconvenience for extracting line structures. In this work, we developed a vascular image segmentation method by enhancing vessel details which should be useful for estimating statistics like micro-vessel density. Since the eigenvalues of hessian matrix and its sign describes different geometric structure in images, which enable to construct vascular similarity function and enhance line signals, the main idea of our method is to cluster the pixel values of the enhanced image. Our method contained three steps: 1) calculate the multiscale gradients and the differences between eigenvalues of Hessian matrix. 2) In order to generate the enhanced microvessels structures, a feed forward neural network was trained by 2.26 million pixels for dealing with the correlations between multi-scale gradients and the differences between eigenvalues. 3) The fuzzy local information c-means clustering (FLICM) was used to cluster the pixel values in enhance line signals. To verify the feasibility and effectiveness of this method, mouse brain vascular images have been acquired by a commercial light-sheet microscope in our lab. The experiment of the segmentation method showed that dice similarity coefficient can reach up to 85%. The results illustrated that our approach extracting line structures of blood vessels dramatically improves the vascular image and enable to accurately extract blood vessels in LSFM images.

Hardening characteristics of CO2 laser welds in advanced high strength steel

NASA Astrophysics Data System (ADS)

Han, Tae-Kyo; Park, Bong-Gyu; Kang, Chung-Yun

2012-06-01

When the CO2 laser welder with 6 kW output was used to weld 4 TRIP steels, 2 DP steels and a precipitation-hardened steel, which have the tensile strength in the range of 600-1000 MPa, the effect of welding speed on hardening characteristics was investigated. In the weld of TRIP steels and DP steels, the maximum hardness was shown in the fusion zone and the HAZ near the bond line, and the hardness was decreased from the HAZ to the base metal. Only in the PH600 steel, the maximum hardness was shown in the fusion zone and the hardness was decreased from bond line to the base metal. The maximum hardness value was not changed due to the variation of the welding speed within a given range of the welding speed. When the correlation with maximum hardness value using 6 known carbon equivalents was examined, those of CEL (=C+Si/50+Mn/25+P/2+Cr/25) and PL (=C+Mn/22+14B) were 0.96 and 0.95 respectively, and CEL was better because it could reflect the contribution of Si and Cr added to AHSS. The maximum hardness value could be calculated by the equation "Hmax=701CEL+281". The phase transformation analysis indicated that only martensitic transformation was expected in the given range of the welding conditions. Therefore, the maximum hardness of the weld was the same as that of water cooled steel and not changed with the variation of the welding speed

AdaBoost-based on-line signature verifier

NASA Astrophysics Data System (ADS)

Hongo, Yasunori; Muramatsu, Daigo; Matsumoto, Takashi

2005-03-01

Authentication of individuals is rapidly becoming an important issue. The authors previously proposed a Pen-input online signature verification algorithm. The algorithm considers a writer"s signature as a trajectory of pen position, pen pressure, pen azimuth, and pen altitude that evolve over time, so that it is dynamic and biometric. Many algorithms have been proposed and reported to achieve accuracy for on-line signature verification, but setting the threshold value for these algorithms is a problem. In this paper, we introduce a user-generic model generated by AdaBoost, which resolves this problem. When user- specific models (one model for each user) are used for signature verification problems, we need to generate the models using only genuine signatures. Forged signatures are not available because imposters do not give forged signatures for training in advance. However, we can make use of another's forged signature in addition to the genuine signatures for learning by introducing a user generic model. And Adaboost is a well-known classification algorithm, making final decisions depending on the sign of the output value. Therefore, it is not necessary to set the threshold value. A preliminary experiment is performed on a database consisting of data from 50 individuals. This set consists of western-alphabet-based signatures provide by a European research group. In this experiment, our algorithm gives an FRR of 1.88% and an FAR of 1.60%. Since no fine-tuning was done, this preliminary result looks very promising.

Cut-off optimization for 13C-urea breath test in a community-based trial by mathematic, histology and serology approach.

PubMed

Li, Zhe-Xuan; Huang, Lei-Lei; Liu, Cong; Formichella, Luca; Zhang, Yang; Wang, Yu-Mei; Zhang, Lian; Ma, Jun-Ling; Liu, Wei-Dong; Ulm, Kurt; Wang, Jian-Xi; Zhang, Lei; Bajbouj, Monther; Li, Ming; Vieth, Michael; Quante, Michael; Zhou, Tong; Wang, Le-Hua; Suchanek, Stepan; Soutschek, Erwin; Schmid, Roland; Classen, Meinhard; You, Wei-Cheng; Gerhard, Markus; Pan, Kai-Feng

2017-05-18

The performance of diagnostic tests in intervention trials of Helicobacter pylori (H.pylori) eradication is crucial, since even minor inaccuracies can have major impact. To determine the cut-off point for 13 C-urea breath test ( 13 C-UBT) and to assess if it can be further optimized by serologic testing, mathematic modeling, histopathology and serologic validation were applied. A finite mixture model (FMM) was developed in 21,857 subjects, and an independent validation by modified Giemsa staining was conducted in 300 selected subjects. H.pylori status was determined using recomLine H.pylori assay in 2,113 subjects with a borderline 13 C-UBT results. The delta over baseline-value (DOB) of 3.8 was an optimal cut-off point by a FMM in modelling dataset, which was further validated as the most appropriate cut-off point by Giemsa staining (sensitivity = 94.53%, specificity = 92.93%). In the borderline population, 1,468 subjects were determined as H.pylori positive by recomLine (69.5%). A significant correlation between the number of positive H.pylori serum responses and DOB value was found (r s  = 0.217, P < 0.001). A mathematical approach such as FMM might be an alternative measure in optimizing the cut-off point for 13 C-UBT in community-based studies, and a second method to determine H.pylori status for subjects with borderline value of 13 C-UBT was necessary and recommended.

High static gain single-phase PFC based on a hybrid boost converter

NASA Astrophysics Data System (ADS)

Flores Cortez, Daniel; Maccarini, Marcello C.; Mussa, Samir A.; Barbi, Ivo

2017-05-01

In this paper, a single-phase unity power factor rectifier, based on a hybrid boost converter, resulting from the integration of a conventional dc-dc boost converter and a switched-capacitor voltage doubler is proposed, analysed, designed and tested. The high-power rectifier is controlled by two feedback loops with the same control strategy employed in the conventional boost-based rectifier. The main feature of the proposed rectifier is its ability to output a dc voltage larger than the double of the peak value of the input line voltage, while subjecting the power switches to half of the dc-link voltage, which contributes to reducing the cost and increasing the efficiency. Experimental data were obtained from a laboratory prototype with an input voltage of 220 Vrms, line frequency of 60 Hz, output voltage of 800 Vdc, load power of 1000 W and switching frequency of 50 kHz. The efficiency of the prototype, measured in the laboratory, was 96.5% for full load and 97% for half load.

A comparison of coronal X-ray structures of active regions with magnetic fields computed from photospheric observations

NASA Technical Reports Server (NTRS)

Poletto, G.; Vaiana, G. S.; Zombeck, M. V.; Krieger, A. S.; Timothy, A. F.

1975-01-01

The appearances of several X-ray active regions observed on March 7, 1970 and June 15, 1973 are compared with the corresponding coronal magnetic-field topology. Coronal fields have been computed from measurements of the longitudinal component of the underlying magnetic fields, based on the current-free hypothesis. An overall correspondence between X-ray structures and calculated field lines is established, and the magnetic counterparts of different X-ray features are also examined. A correspondence between enhanced X-ray emission and the location of compact closed field lines is suggested. Representative magnetic-field values calculated under the assumption of current-free fields are given for heights up to 200 sec.

Gravimetric surveys for assessing rock mass condition around a mine shaft

NASA Astrophysics Data System (ADS)

Madej, Janusz

2017-06-01

The fundamentals of use of vertical gravimetric surveying method in mine shafts are presented in the paper. The methods of gravimetric measurements and calculation of interval and complex density are discussed in detail. The density calculations are based on an original method accounting for the gravity influence of the mine shaft thus guaranteeing closeness of calculated and real values of density of rocks beyond the shaft lining. The results of many gravimetric surveys performed in shafts are presented and interpreted. As a result, information about the location of heterogeneous zones of work beyond the shaft lining is obtained. In many cases, these zones used to threaten the safe operation of machines and utilities in the shaft.

Continuous-variable quantum key distribution in non-Markovian channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasile, Ruggero; Olivares, Stefano; CNISM, Unita di Ricerca di Milano Universita, I-20133 Milano

2011-04-15

We address continuous-variable quantum key distribution (QKD) in non-Markovian lossy channels and show how the non-Markovian features may be exploited to enhance security and/or to detect the presence and the position of an eavesdropper along the transmission line. In particular, we suggest a coherent-state QKD protocol which is secure against Gaussian individual attacks based on optimal 1{yields}2 asymmetric cloning machines for arbitrarily low values of the overall transmission line. The scheme relies on specific non-Markovian properties, and cannot be implemented in ordinary Markovian channels characterized by uniform losses. Our results give a clear indication of the potential impact of non-Markovianmore » effects in QKD.« less

Data Parallel Line Relaxation (DPLR) Code User Manual: Acadia - Version 4.01.1

NASA Technical Reports Server (NTRS)

Wright, Michael J.; White, Todd; Mangini, Nancy

2009-01-01

Data-Parallel Line Relaxation (DPLR) code is a computational fluid dynamic (CFD) solver that was developed at NASA Ames Research Center to help mission support teams generate high-value predictive solutions for hypersonic flow field problems. The DPLR Code Package is an MPI-based, parallel, full three-dimensional Navier-Stokes CFD solver with generalized models for finite-rate reaction kinetics, thermal and chemical non-equilibrium, accurate high-temperature transport coefficients, and ionized flow physics incorporated into the code. DPLR also includes a large selection of generalized realistic surface boundary conditions and links to enable loose coupling with external thermal protection system (TPS) material response and shock layer radiation codes.

Genomic prediction based on data from three layer lines using non-linear regression models.

PubMed

Huang, Heyun; Windig, Jack J; Vereijken, Addie; Calus, Mario P L

2014-11-06

Most studies on genomic prediction with reference populations that include multiple lines or breeds have used linear models. Data heterogeneity due to using multiple populations may conflict with model assumptions used in linear regression methods. In an attempt to alleviate potential discrepancies between assumptions of linear models and multi-population data, two types of alternative models were used: (1) a multi-trait genomic best linear unbiased prediction (GBLUP) model that modelled trait by line combinations as separate but correlated traits and (2) non-linear models based on kernel learning. These models were compared to conventional linear models for genomic prediction for two lines of brown layer hens (B1 and B2) and one line of white hens (W1). The three lines each had 1004 to 1023 training and 238 to 240 validation animals. Prediction accuracy was evaluated by estimating the correlation between observed phenotypes and predicted breeding values. When the training dataset included only data from the evaluated line, non-linear models yielded at best a similar accuracy as linear models. In some cases, when adding a distantly related line, the linear models showed a slight decrease in performance, while non-linear models generally showed no change in accuracy. When only information from a closely related line was used for training, linear models and non-linear radial basis function (RBF) kernel models performed similarly. The multi-trait GBLUP model took advantage of the estimated genetic correlations between the lines. Combining linear and non-linear models improved the accuracy of multi-line genomic prediction. Linear models and non-linear RBF models performed very similarly for genomic prediction, despite the expectation that non-linear models could deal better with the heterogeneous multi-population data. This heterogeneity of the data can be overcome by modelling trait by line combinations as separate but correlated traits, which avoids the occasional occurrence of large negative accuracies when the evaluated line was not included in the training dataset. Furthermore, when using a multi-line training dataset, non-linear models provided information on the genotype data that was complementary to the linear models, which indicates that the underlying data distributions of the three studied lines were indeed heterogeneous.

Uncertainties in Atomic Data and Their Propagation Through Spectral Models. I.

NASA Technical Reports Server (NTRS)

Bautista, M. A.; Fivet, V.; Quinet, P.; Dunn, J.; Gull, T. R.; Kallman, T. R.; Mendoza, C.

2013-01-01

We present a method for computing uncertainties in spectral models, i.e., level populations, line emissivities, and emission line ratios, based upon the propagation of uncertainties originating from atomic data.We provide analytic expressions, in the form of linear sets of algebraic equations, for the coupled uncertainties among all levels. These equations can be solved efficiently for any set of physical conditions and uncertainties in the atomic data. We illustrate our method applied to spectral models of Oiii and Fe ii and discuss the impact of the uncertainties on atomic systems under different physical conditions. As to intrinsic uncertainties in theoretical atomic data, we propose that these uncertainties can be estimated from the dispersion in the results from various independent calculations. This technique provides excellent results for the uncertainties in A-values of forbidden transitions in [Fe ii]. Key words: atomic data - atomic processes - line: formation - methods: data analysis - molecular data - molecular processes - techniques: spectroscopic

Fluorescence-based monitoring of tracer and substrate distribution in an UASB reactor.

PubMed

Lou, S J; Tartakovsky, B; Zeng, Y; Wu, P; Guiot, S R

2006-11-01

In this work, rhodamine-related fluorescence was measured on-line at four reactor heights in order to study hydrodynamics within an upflow anaerobic sludge bed reactor. A linear dependence of the dispersion coefficient (D) on the upflow velocity was observed, while the influence of the organic loading rate (OLR) was insignificant. Furthermore, the Bodenstein number of the reactor loaded with granulated sludge was found to be position-dependent with the largest values measured at the bottom of the sludge bed. This trend was not observed in the reactor without sludge. Chemical oxygen demand (COD) and volatile fatty acid (VFA) concentrations were measured at the same reactor heights as in rhodamine tests using conventional off-line analytical methods and on-line multiwavelength fluorometry. Significant spatial COD and VFA gradients were observed at organic loading rates above 6g COD l(R)(-1)d(-1) and linear upflow velocities below 0.8m h(-1).

Characterizing the Circumgalactic Medium of Nearby Galaxies with HST/COS and HST/STIS Absorption-line Spectroscopy. II. Methods and Models

NASA Astrophysics Data System (ADS)

Keeney, Brian A.; Stocke, John T.; Danforth, Charles W.; Shull, J. Michael; Pratt, Cameron T.; Froning, Cynthia S.; Green, James C.; Penton, Steven V.; Savage, Blair D.

2017-05-01

We present basic data and modeling for a survey of the cool, photoionized circumgalactic medium (CGM) of low-redshift galaxies using far-UV QSO absorption-line probes. This survey consists of “targeted” and “serendipitous” CGM subsamples, originally described in Stocke et al. (Paper I). The targeted subsample probes low-luminosity, late-type galaxies at z< 0.02 with small impact parameters (< ρ > =71 kpc), and the serendipitous subsample probes higher luminosity galaxies at z≲ 0.2 with larger impact parameters (< ρ > =222 kpc). Hubble Space Telescope and FUSE UV spectroscopy of the absorbers and basic data for the associated galaxies, derived from ground-based imaging and spectroscopy, are presented. We find broad agreement with the COS-Halos results, but our sample shows no evidence for changing ionization parameter or hydrogen density with distance from the CGM host galaxy, probably because the COS-Halos survey probes the CGM at smaller impact parameters. We find at least two passive galaxies with H I and metal-line absorption, confirming the intriguing COS-Halos result that galaxies sometimes have cool gas halos despite no on-going star formation. Using a new methodology for fitting H I absorption complexes, we confirm the CGM cool gas mass of Paper I, but this value is significantly smaller than that found by the COS-Halos survey. We trace much of this difference to the specific values of the low-z metagalactic ionization rate assumed. After accounting for this difference, a best-value for the CGM cool gas mass is found by combining the results of both surveys to obtain {log}(M/{M}⊙ )=10.5+/- 0.3, or ˜30% of the total baryon reservoir of an L≥slant {L}* , star-forming galaxy. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by AURA, Inc., under NASA contract NAS 5-26555.

Combined Ultraviolet and Optical Spectra of 48 Low-Redshift QSOs and the Relation of the Continuum and Emission-Line Properties

NASA Astrophysics Data System (ADS)

Corbin, Michael R.; Boroson, Todd A.

1996-11-01

We present combined ultraviolet and optical spectra of 48 QSOs and Seyfert 1 galaxies in the redshift range 0.034-0.774. The UV spectra were obtained non-simultaneously with the optical and are derived from archival Hubble Space Telescope (HST) Faint Object Spectrograph and International Ultraviolet Explorer (IUE) observations. The sample consists of 22 radio- quiet objects, 12 flat radio spectrum radio-loud objects, and 14 steep radio spectrum objects, and it covers approximately 2.5 decades in ultraviolet continuum luminosity. The sample objects are among the most luminous known in this redshift range and include 3C 273 and Fairall 9, as well as many objects discovered in the Bright Quasar Survey. We measure and compare an array of emission-line and continuum parameters, including 2 keV X-ray luminosities derived from the Einstein database. We examine individual correlations and also apply a principal components analysis (PCA) in an effort to determine the underlying sources of variance among these observables. Our main results are as follows. 1. The C IV λ1549 profile asymmetry is correlated with the UV continuum luminosity measured at the position of that line, such that increasing continuum luminosity produces increasing redward asymmetry. This is the same correlation found between Hβ asymmetry and 2 keV luminosity in a larger sample of objects and appears to be followed by both radio-loud and radio-quiet sources. The C IV profile asymmetry is also correlated with the FWZI of the Lyα profile, with more redward asymmetric profiles associated with wider profile bases. The PCA reveals that the correlated increase in luminosity, C IV redward asymmetry, and profile base width accounts for over half the statistical variance in the sample. 2. There is a statistically significant difference between the FWZI distributions of the Lyα and Hβ lines, such that the former is wider on average by ~10^4^ km s^-1^. The FWHM values of the broad Hβ line are weakly correlated with those of C IV λ1549 and Lyα, and in contrast to the FWZI values the Hβ profiles are wider. Measures of the asymmetry of the Hβ and C IV profiles also show a weak correlation. The wavelength centroids at 3/4 maximum of the Lyα and C IV lines also show average blueshifts ~50-200 km s^-1^ from [O III] λ5007, versus an average redshift of 75 km s^-1^ for broad Hβ. 3. There is no clear evidence of narrow components to the stronger UV lines, even among objects in which the optical narrow lines including [O III] λλ4959, 5007 are unusually strong. We measure the average fractional contributions of such components to the Lyα and C III] λ1909 lines to be ~4%-5%, consistent with the findings from smaller samples. However, a sizable fraction (50%) of radio-loud objects display a narrow component of He II λ1640, the same as in the QSO population at intermediate redshifts, and such a component is likely to contribute to the other UV lines. We interpret the first result as the effect of a black hole mass/luminosity relation in which the profile widths and redward asymmetries are produced respectively by the virialized motions and gravitational redshift associated with 10^9^-10^10^ M_sun_ holes. This does not explain the cases of blueward profile asymmetries and blueshifted profile peaks, which require an effect acting oppositely to gravitational redshift. The peak redshift differences and relative weakness of the correlations between the UV profile widths and asymmetries and those of Hβ suggests a stratified ionization structure of the broad-line region (BLR), consistent with the variability studies of Seyfert 1 galaxies. Continuum variability and the dynamical evolution of the BLR gas may also influence these results. The difference between the Lyα and Hβ FWZI values provides additional evidence of an optically thin very broad line region (VBLR) lying interior to an intermediate line region (ILR) producing the profile cores. The smaller average FWHM values of the UV lines compared to Hβ indicate that they have a higher relative contribution of ILR emission, versus a more dominant VBLR component in the Balmer lines. The narrow He II λ1640 feature of radio-loud objects is likely associated with the inner regions of extended (100 kpc) ionized halos that are not present around radio-quiet objects, and which appear to be best explained as cooling flows around the QSO host galaxies.

Computational nanometrology of line-edge roughness: noise effects, cross-line correlations and the role of etch transfer

NASA Astrophysics Data System (ADS)

Constantoudis, Vassilios; Papavieros, George; Lorusso, Gian; Rutigliani, Vito; Van Roey, Frieda; Gogolides, Evangelos

2018-03-01

The aim of this paper is to investigate the role of etch transfer in two challenges of LER metrology raised by recent evolutions in lithography: the effects of SEM noise and the cross-line and edge correlations. The first comes from the ongoing scaling down of linewidths, which dictates SEM imaging with less scanning frames to reduce specimen damage and hence with more noise. During the last decade, it has been shown that image noise can be an important budget of the measured LER while systematically affects and alter the PSD curve of LER at high frequencies. A recent method for unbiased LER measurement is based on the systematic Fourier or correlation analysis to decompose the effects of noise from true LER (Fourier-Correlation filtering method). The success of the method depends on the PSD and HHCF curve. Previous experimental and model works have revealed that etch transfer affects the PSD of LER reducing its high frequency values. In this work, we estimate the noise contribution to the biased LER through PSD flat floor at high frequencies and relate it with the differences between the PSDs of lithography and etched LER. Based on this comparison, we propose an improvement of the PSD/HHCF-based method for noise-free LER measurement to include the missed high frequency real LER. The second issue is related with the increased density of lithographic patterns and the special characteristics of DSA and MP lithography patterns exhibits. In a previous work, we presented an enlarged LER characterization methodology for such patterns, which includes updated versions of the old metrics along with new metrics defined and developed to capture cross-edge and cross-line correlations. The fundamental concept has been the Line Center Roughness (LCR), the edge c-factor and the line c-factor correlation function and length quantifying the line fluctuations and the extent of cross-edge and cross-line correlations. In this work, we focus on the role of etch steps on cross-edge and line correlation metrics in SAQP data. We find that the spacer etch steps reduce edge correlations while etch steps with pattern transfer increase these. Furthermore, the density doubling and quadrupling increase edge correlations as well as cross-line correlations.

Combining low- to high-resolution transit spectroscopy of HD 189733b. Linking the troposphere and the thermosphere of a hot gas giant

NASA Astrophysics Data System (ADS)

Pino, Lorenzo; Ehrenreich, David; Wyttenbach, Aurélien; Bourrier, Vincent; Nascimbeni, Valerio; Heng, Kevin; Grimm, Simon; Lovis, Christophe; Malik, Matej; Pepe, Francesco; Piotto, Giampaolo

2018-04-01

Space-borne low- to medium-resolution (ℛ 102-103) and ground-based high-resolution spectrographs (ℛ 105) are commonly used to obtain optical and near infrared transmission spectra of exoplanetary atmospheres. In this wavelength range, space-borne observations detect the broadest spectral features (alkali doublets, molecular bands, scattering, etc.), while high-resolution, ground-based observations probe the sharpest features (cores of the alkali lines, molecular lines). The two techniques differ by several aspects. (1) The line spread function of ground-based observations is 103 times narrower than for space-borne observations; (2) Space-borne transmission spectra probe up to the base of thermosphere (P ≳ 10-6 bar), while ground-based observations can reach lower pressures (down to 10-11 bar) thanks to their high resolution; (3) Space-borne observations directly yield the transit depth of the planet, while ground-based observations can only measure differences in the apparent size of the planet at different wavelengths. These differences make it challenging to combine both techniques. Here, we develop a robust method to compare theoretical models with observations at different resolutions. We introduce πη, a line-by-line 1D radiative transfer code to compute theoretical transmission spectra over a broad wavelength range at very high resolution (ℛ 106, or Δλ 0.01 Å). An hybrid forward modeling/retrieval optimization scheme is devised to deal with the large computational resources required by modeling a broad wavelength range 0.3-2 μm at high resolution. We apply our technique to HD 189733b. In this planet, HST observations reveal a flattened spectrum due to scattering by aerosols, while high-resolution ground-based HARPS observations reveal sharp features corresponding to the cores of sodium lines. We reconcile these apparent contrasting results by building models that reproduce simultaneously both data sets, from the troposphere to the thermosphere. We confirm: (1) the presence of scattering by tropospheric aerosols; (2) that the sodium core feature is of thermospheric origin. When we take into account the presence of aerosols, the large contrast of the core of the sodium lines measured by HARPS indicates a temperature of up to 10 000K in the thermosphere, higher than what reported in the literature. We also show that the precise value of the thermospheric temperature is degenerate with the relative optical depth of sodium, controlled by its abundance, and of the aerosol deck.

Simultaneous determination of thirteen different steroid hormones using micro UHPLC-MS/MS with on-line SPE system.

PubMed

Márta, Zoltán; Bobály, Balázs; Fekete, Jenő; Magda, Balázs; Imre, Tímea; Mészáros, Katalin Viola; Bálint, Mária; Szabó, Pál Tamás

2018-02-20

Ultratrace analysis of sample components requires excellent analytical performance in terms of limits of quantitation (LOQ). Micro UHPLC coupled to sensitive tandem mass spectrometry provides state of the art solution for such analytical problems. Using on-line SPE with column switching on a micro UHPLC-MS/MS system allowed to decrease LOQ without any complex sample preparation protocol. The presented method is capable of reaching satisfactory low LOQ values for analysis of thirteen different steroid molecules from human plasma without the most commonly used off-line SPE or compound derivatization. Steroids were determined by using two simple sample preparation methods, based on lower and higher plasma steroid concentrations. In the first method, higher analyte concentrations were directly determined after protein precipitation with methanol. The organic phase obtained from the precipitation was diluted with water and directly injected into the LC-MS system. In the second method, low steroid levels were determined by concentrating the organic phase after steroid extraction. In this case, analytes were extracted with ethyl acetate and reconstituted in 90/10 water/acetonitrile following evaporation to dryness. This step provided much lower LOQs, outperforming previously published values. The method has been validated and subsequently applied to clinical laboratory measurement. Copyright © 2017 Elsevier B.V. All rights reserved.

Two protogalaxy candidates in one night

NASA Technical Reports Server (NTRS)

Eisenhardt, Peter; Dickinson, Mark

1993-01-01

In spite of a lookback time of 77 to 89 percent of the age of the universe, Lilly provided evidence that the dominant stellar population in 0902 was surprisingly old, over 1 Gyr. This age estimate was based on the values K = 18.8 and I-K = 4.5 in the central 3.5 x 3.5 inch. At Lilly's suggestion, we reobserved 0902 at K, and in initial reductions of our data found only an upper limit (K greater than 19.5). After extensive experimentation with reduction techniques and correction for low-level systematic effects, we succeeded in extracting a four sigma detection at K = 19.9 in a 4 inch diameter circular aperture. The morphology and location of this detection were more reminescent of the Ly alpha image than of CCD continuum images, and in Mar. 1992, we obtained a narrow band image which included redshifted (OIII) 4959,5007 A line emission at 2.20 microns. This (OIII) image gave a strong detection which demonstrates that most of the central K flux, already reduced by a magnitude, is due to line emission. Our formal line corrected values in a 4 inch aperture are K = 21.5 and R-K = 1.9. Hence, 0902 has been transformed from relaxed maturity into unsettled youth.

Scanning electron microscope measurement of width and shape of 10nm patterned lines using a JMONSEL-modeled library.

PubMed

Villarrubia, J S; Vladár, A E; Ming, B; Kline, R J; Sunday, D F; Chawla, J S; List, S

2015-07-01

The width and shape of 10nm to 12 nm wide lithographically patterned SiO2 lines were measured in the scanning electron microscope by fitting the measured intensity vs. position to a physics-based model in which the lines' widths and shapes are parameters. The approximately 32 nm pitch sample was patterned at Intel using a state-of-the-art pitch quartering process. Their narrow widths and asymmetrical shapes are representative of near-future generation transistor gates. These pose a challenge: the narrowness because electrons landing near one edge may scatter out of the other, so that the intensity profile at each edge becomes width-dependent, and the asymmetry because the shape requires more parameters to describe and measure. Modeling was performed by JMONSEL (Java Monte Carlo Simulation of Secondary Electrons), which produces a predicted yield vs. position for a given sample shape and composition. The simulator produces a library of predicted profiles for varying sample geometry. Shape parameter values are adjusted until interpolation of the library with those values best matches the measured image. Profiles thereby determined agreed with those determined by transmission electron microscopy and critical dimension small-angle x-ray scattering to better than 1 nm. Published by Elsevier B.V.

Fault location method for unexposed gas trunk line insulation at stray current constant effect area

NASA Astrophysics Data System (ADS)

Tsenev, A. N.; Nosov, V. V.; Akimova, E. V.

2017-10-01

For the purpose of gas trunk lines safe operation, two types of pipe wall metal anticorrosion protection are generally used - the passive (insulation coating) protection and the active (electrochemical) protection. In the process of a pipeline long-term operation, its insulation is subject to wear and damage. Electrochemical protection means of a certain potential value prevent metal dissolution in the soil. When insulation wear and tear attains a level of insufficiency of the protection potential value, the insulating coating needs repair which is a labor-consuming procedure. To reduce the risk of such situation, it is necessary to make inspection rounds to monitor the condition of pipe insulation. A method for pipeline insulation coating unexposed fault location based on Pearson method is considered, wherein a working cathodic protection station signal of 100 Hz frequency is used, which makes installation of a generator unnecessary, and also a specific generator signal of 1 kHz frequency is used at high noise immunity and sensitivity of the instrument complex. This method enables detection and sizing of unexposed pipeline defects within the zones of earth current permanent action. High noise immunity of selective indicators allows for operation in proximity to 110 kV, 220 kV, and 500 kV power transmission lines in action.

Total reflection X-ray Fluorescence determination of interfering elements rubidium and uranium by profile fitting

NASA Astrophysics Data System (ADS)

Dhara, Sangita; Khooha, Ajay; Singh, Ajit Kumar; Tiwari, M. K.; Misra, N. L.

2018-06-01

Systematic studies to assess the analytical parameters obtained in the total reflection X-ray fluorescence (TXRF) determinations of interfering elements Rb and U using profile fitting are reported in the present manuscript. The X-ray lines Rb Kα and U Lα having serious spectral interference (ΔE = 218 eV), have been used as analytical lines. The intensities of these X-ray lines have been assessed using profile fitting. In order to compare the analytical results of Rb determinations in presence of U, with and without U excitation, synchrotron radiation was tuned to energy just above and below the U Labs edge. This approach shall excite both Rb Kα and U Lα simultaneously and Rb Kα selectively. Finally, the samples were also analyzed with a laboratory based TXRF spectrometer. The analytical results obtained in all these conditions were comparable. The authenticity of the results was assessed by analyzing U with respect to Rb in Rb2U(SO4)3, a standard reference material for U. The average precision obtained for TXRF determinations was below 3% (RSD, n = 3, 1σ) and the percent deviation of TXRF values from the expected values calculated on the basis of sample preparation was within 3%.

Study of the effect of electromagnetic fields on indoor and outdoor radon concentrations

NASA Astrophysics Data System (ADS)

Haider, Lina M.; Shareef, N. R.; Darwoysh, H. H.; Mansour, H. L.

2018-05-01

In the present work, the effect of electromagnetic fields produced by high voltage power lines(132kV) and indoor equipments on the indoor and outdoor average radon concentrations in Al-Kazaliya and Hay Al-Adil regions in Baghdad city were studied using CR-39 track detectors and a gauss-meter.Results of measurements of the present study, have shown that the highest value for the indoor average radon concentration (76.56± 8.44 Bq / m3) was recorded for sample A1(Hay Al-Adel) at a distance of (20 m) from the high voltage power lines, while the lowest value for the indoor average radon concentration (30.46 ± 8.44 Bq / m3) was recorded for sample A3 (Hay Al-Adil) at a distance of (50 m) from the high voltage power lines. The indoor gaussmeter measurements were found to be ranged from (30.2 mG) to (38.5 mG). The higest value for outdoor average radon concentration and the highest gaussmeter measurements were found for sample (1), with values (92.63 ±11.2 Bq / m3) and (87.24 ± 2.85 mG), directly under the high voltage power lines respectively, while the lowest outdoor average radon concentration and the lowest gaussmeter measurements were found in sample (4),with values (34.19 ± 6.33 Bq / m3) and (1.16 ± 0.14 Bq / m3),), at a distance of (120 m) from the high voltage power lines respectively. The results of the present work have shown that there might be an influence of the electromagnetic field on radon concentrations in areas which were close to high voltage power lines and houses which have used many electric equipment for a long period of time.

Sensorless FOC Performance Improved with On-Line Speed and Rotor Resistance Estimator Based on an Artificial Neural Network for an Induction Motor Drive

PubMed Central

Gutierrez-Villalobos, Jose M.; Rodriguez-Resendiz, Juvenal; Rivas-Araiza, Edgar A.; Martínez-Hernández, Moisés A.

2015-01-01

Three-phase induction motor drive requires high accuracy in high performance processes in industrial applications. Field oriented control, which is one of the most employed control schemes for induction motors, bases its function on the electrical parameter estimation coming from the motor. These parameters make an electrical machine driver work improperly, since these electrical parameter values change at low speeds, temperature changes, and especially with load and duty changes. The focus of this paper is the real-time and on-line electrical parameters with a CMAC-ADALINE block added in the standard FOC scheme to improve the IM driver performance and endure the driver and the induction motor lifetime. Two kinds of neural network structures are used; one to estimate rotor speed and the other one to estimate rotor resistance of an induction motor. PMID:26131677

Sensorless FOC Performance Improved with On-Line Speed and Rotor Resistance Estimator Based on an Artificial Neural Network for an Induction Motor Drive.

PubMed

Gutierrez-Villalobos, Jose M; Rodriguez-Resendiz, Juvenal; Rivas-Araiza, Edgar A; Martínez-Hernández, Moisés A

2015-06-29

Three-phase induction motor drive requires high accuracy in high performance processes in industrial applications. Field oriented control, which is one of the most employed control schemes for induction motors, bases its function on the electrical parameter estimation coming from the motor. These parameters make an electrical machine driver work improperly, since these electrical parameter values change at low speeds, temperature changes, and especially with load and duty changes. The focus of this paper is the real-time and on-line electrical parameters with a CMAC-ADALINE block added in the standard FOC scheme to improve the IM driver performance and endure the driver and the induction motor lifetime. Two kinds of neural network structures are used; one to estimate rotor speed and the other one to estimate rotor resistance of an induction motor.

Method And Apparatus For Two Dimensional Surface Property Analysis Based On Boundary Measurement

DOEpatents

Richardson, John G.

2005-11-15

An apparatus and method for determining properties of a conductive film is disclosed. A plurality of probe locations selected around a periphery of the conductive film define a plurality of measurement lines between each probe location and all other probe locations. Electrical resistance may be measured along each of the measurement lines. A lumped parameter model may be developed based on the measured values of electrical resistance. The lumped parameter model may be used to estimate resistivity at one or more selected locations encompassed by the plurality of probe locations. The resistivity may be extrapolated to other physical properties if the conductive film includes a correlation between resistivity and the other physical properties. A profile of the conductive film may be developed by determining resistivity at a plurality of locations. The conductive film may be applied to a structure such that resistivity may be estimated and profiled for the structure's surface.

Glove-based approach to online signature verification.

PubMed

Kamel, Nidal S; Sayeed, Shohel; Ellis, Grant A

2008-06-01

Utilizing the multiple degrees of freedom offered by the data glove for each finger and the hand, a novel on-line signature verification system using the Singular Value Decomposition (SVD) numerical tool for signature classification and verification is presented. The proposed technique is based on the Singular Value Decomposition in finding r singular vectors sensing the maximal energy of glove data matrix A, called principal subspace, so the effective dimensionality of A can be reduced. Having modeled the data glove signature through its r-principal subspace, signature authentication is performed by finding the angles between the different subspaces. A demonstration of the data glove is presented as an effective high-bandwidth data entry device for signature verification. This SVD-based signature verification technique is tested and its performance is shown to be able to recognize forgery signatures with a false acceptance rate of less than 1.2%.

Object-Based Mapping of the Circumpolar Taiga-Tundra Ecotone with MODIS Tree Cover

NASA Technical Reports Server (NTRS)

Ranson, K. J.; Montesano, P. M.; Nelson, R.

2011-01-01

The circumpolar taiga tundra ecotone was delineated using an image-segmentation-based mapping approach with multi-annual MODIS Vegetation Continuous Fields (VCF) tree cover data. Circumpolar tree canopy cover (TCC) throughout the ecotone was derived by averaging MODIS VCF data from 2000 to 2005 and adjusting the averaged values using linear equations relating MODIS TCC to Quickbird-derived tree cover estimates. The adjustment helped mitigate VCF's overestimation of tree cover in lightly forested regions. An image segmentation procedure was used to group pixels representing similar tree cover into polygonal features (segmentation objects) that form the map of the transition zone. Each polygon represents an area much larger than the 500 m MODIS pixel and characterizes the patterns of sparse forest patches on a regional scale. Those polygons near the boreal/tundra interface with either (1) mean adjusted TCC values from5 to 20%, or (2) mean adjusted TCC values greater than 5% but with a standard deviation less than 5% were used to identify the ecotone. Comparisons of the adjusted average tree cover data were made with (1) two existing tree line definitions aggregated for each 1 degree longitudinal interval in North America and Eurasia, (2) Landsat-derived Canadian proportion of forest cover for Canada, and (3) with canopy cover estimates extracted from airborne profiling lidar data that transected 1238 of the TCC polygons. The adjusted TCC from MODIS VCF shows, on average, less than 12% TCC for all but one regional zone at the intersection with independently delineated tree lines. Adjusted values track closely with Canadian proportion of forest cover data in areas of low tree cover. A comparison of the 1238 TCC polygons with profiling lidar measurements yielded an overall accuracy of 67.7%.

Tracking the Genetic Stability of a Honey Bee (Hymenoptera: Apidae) Breeding Program With Genetic Markers.

PubMed

Bourgeois, Lelania; Beaman, Lorraine

2017-08-01

A genetic stock identification (GSI) assay was developed in 2008 to distinguish Russian honey bees from other honey bee stocks that are commercially produced in the United States. Probability of assignment (POA) values have been collected and maintained since the stock release in 2008 to the Russian Honey Bee Breeders Association. These data were used to assess stability of the breeding program and the diversity levels of the contemporary breeding stock through comparison of POA values and genetic diversity parameters from the initial release to current values. POA values fluctuated throughout 2010-2016, but have recovered to statistically similar levels in 2016 (POA(2010) = 0.82, POA(2016) = 0.74; P = 0.33). Genetic diversity parameters (i.e., allelic richness and gene diversity) in 2016 also remained at similar levels when compared to those in 2010. Estimates of genetic structure revealed stability (FST(2009/2016) = 0.0058) with a small increase in the estimate of the inbreeding coefficient (FIS(2010) = 0.078, FIS(2016) = 0.149). The relationship among breeding lines, based on genetic distance measurement, was similar in 2008 and 2016 populations, but with increased homogeneity among lines (i.e., decreased genetic distance). This was expected based on the closed breeding system used for Russian honey bees. The successful application of the GSI assay in a commercial breeding program demonstrates the utility and stability of such technology to contribute to and monitor the genetic integrity of a breeding stock of an insect species. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

Liquid-liquid equilibria for the ternary systems sulfolane + octane + benzene, sulfolane + octane + toluene and sulfolane + octane + p-xylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.; Kim, H.

1995-03-01

Sulfolane is widely used as a solvent for the extraction of aromatic hydrocarbons. Ternary phase equilibrium data are essential for the proper understanding of the solvent extraction process. Liquid-liquid equilibrium data for the systems sulfolane + octane + benzene, sulfolane + octane + toluene and sulfolane + octane + p-xylene were determined at 298.15, 308.15, and 318.15 K. Tie line data were satisfactorily correlated by the Othmer and Tobias method. The experimental data were compared with the values calculated by the UNIQUAC and NRTL models. Good quantitative agreement was obtained with these models. However, the calculated values based on themore » NRTL model were found to be better than those based on the UNIQUAC model.« less

Theoretical Studies of N2-broadened Half-widths of H2O Lines Involving High j States

NASA Technical Reports Server (NTRS)

Ma, Q.; Tipping, R. H.; Lavrentieva, N. N.

2012-01-01

Based on the properties of the energy levels and wave functions of H2O states, one can categorize H2O lines into individually defined groups such that within the same group, the energy levels and the wave functions associated with two paired lines have an identity property while those associated with different pairs have a similarity property. Meanwhile, by thoroughly analyzing processes used to calculate N2-broadened half-widths, it was found that the 'Fourier series' of W(sup a)(sub L(sub 1))(sub K(sub 1))(sub K(sub 1)) (t; j(sub f) T(sub f) and W(sup a)(sub L(sub 1))(sub K(sub 1))(sub K(sub 1)) (t; j(sub i) T(sub i), and a factor P(sub 222) (j(sub f) T(sub f) j(sub i) T(sub i)) are the key items in the Robert-Bonamy formalism to distinguish contributions to ReS2(r(sub c)) among different transitions of j(sub f) T(sub f) - j(sub i). However, these items are completely determined by the energy levels and the wave functions associated with their initial and final states and they must bear the latter's features as well. Thus, it becomes obvious that for two paired lines in the same group, their calculated half-widths must be almost identical and the values associated with different pairs must vary smoothly as their ji values vary. Thus, the pair identity and the smooth variation rules are established within individual groups of lines. One can use these rules to screen half-width data listed in HITRAN and to improve the data accuracies.

Reciprocal Genetics: Identifying QTL for General and Specific Combining Abilities in Hybrids Between Multiparental Populations from Two Maize (Zea mays L.) Heterotic Groups.

PubMed

Giraud, Héloïse; Bauland, Cyril; Falque, Matthieu; Madur, Delphine; Combes, Valérie; Jamin, Philippe; Monteil, Cécile; Laborde, Jacques; Palaffre, Carine; Gaillard, Antoine; Blanchard, Philippe; Charcosset, Alain; Moreau, Laurence

2017-11-01

Several plant and animal species of agricultural importance are commercialized as hybrids to take advantage of the heterosis phenomenon. Understanding the genetic architecture of hybrid performances is therefore of key importance. We developed two multiparental maize ( Zea mays L.) populations, each corresponding to an important heterotic group (dent or flint) and comprised of six connected biparental segregating populations of inbred lines (802 and 822 lines for each group, respectively) issued from four founder lines. Instead of using "testers" to evaluate their hybrid values, segregating lines were crossed according to an incomplete factorial design to produce 951 dent-flint hybrids, evaluated for four biomass production traits in eight environments. QTL detection was carried out for the general-combining-ability (GCA) and specific-combining-ability (SCA) components of hybrid value, considering allelic effects transmitted from each founder line. In total, 42 QTL were detected across traits. We detected mostly QTL affecting GCA, 31% (41% for dry matter yield) of which also had mild effects on SCA. The small impact of dominant effects is consistent with the known differentiation between the dent and flint heterotic groups and the small percentage of hybrid variance due to SCA observed in our design (∼20% for the different traits). Furthermore, most (80%) of GCA QTL were segregating in only one of the two heterotic groups. Relative to tester-based designs, use of hybrids between two multiparental populations appears highly cost efficient to detect QTL in two heterotic groups simultaneously. This presents new prospects for selecting superior hybrid combinations with markers. Copyright © 2017 by the Genetics Society of America.

Antitumor Activities of Rauwolfia vomitoria Extract and Potentiation of Carboplatin Effects Against Ovarian Cancer.

PubMed

Yu, Jun; Ma, Yan; Drisko, Jeanne; Chen, Qi

2013-12-01

Tumor resistance to platinum-based drugs has been an obstacle to the treatment of ovarian cancer. Extract of the plant Rauwolfia vomitoria has long been used by cancer patients. However, there have not been systematic studies of its anticancer activity. In an effort to enhance the effectiveness of platinum-based drugs, we investigated the anticancer effect of a Rauwolfia vomitoria extract (Rau), both alone and in combination with carboplatin (Cp). In vitro cytotoxicity and colony formation were evaluated in several ovarian cancer cell lines. In vivo effects were evaluated in an intraperitoneal ovarian cancer mouse model. The combination of Rau and Cp was assessed using Chou-Talalay's constant ratio design and median effect analysis based on the isobologram principle to determine the combination index values. Rau decreased cell growth in all 3 tested ovarian cancer cell lines dose dependently and completely inhibited formation of colonies in soft agar. Apoptosis was induced in a time- and dose-dependent manner and was the predominant form of Rau-induced cell death. Synergy of Rau with Cp was detected, with combination index values <1 and dose reduction index values for Cp ranging from 1.7- to 7-fold. Tumor growth in mice was significantly suppressed by 36% or 66% with Rau treatment alone at a low (20 mg/kg) or a high dose (50 mg/kg), respectively, an effect comparable to that of Cp alone. The volume of ascitic fluid and the number of nonblood cells in ascites were also significantly decreased. Combining Rau with Cp remarkably enhanced the effect of Cp and reduced tumor burden by 87% to 90% and ascites volume by 89% to 97%. Rau has potent antitumor activity and in combination significantly enhances the effect of Cp against ovarian cancer.

Panel Board From Coconut Fibre And Pet Bottle

NASA Astrophysics Data System (ADS)

Ngadiman, Norhayati; Kaamin, Masiri; Abd. Kadir, Aslila; Sahat, Suhaila; Zaini, Aziza; Raihana Nor Zentan, Siti; Ain Ahmad, Nur; Amran, Wan Haizatul Aisyhah Wan

2018-03-01

The rate of global deforestation and its impact on the environment has led particle board manufacture to search for alternative feedstock, especially in countries where wood is less available compared to other cellulosic natural product. Based on the properties of coconut fibre and PET bottle, these two materials can be recycle as raw material for manufacture of panel board. As for this study, the coconut fibre were used as the filler and PET bottle as outer lining of the panel board. Two types of coconut fibre were used which are grinding and un-grinding coconut fibre. At first, the coconut fibre are undergoes softening, grinding, drying and sieving process, while PET bottle was cleaning, shredding, sieving before compacted using hydraulic hot press machine. There are four types of testing that been carried out which are swelling, water absorption, Modulus of Elasticity (MOE) and Modulus of Rupture (MOR). The result show the conventional board has the highest value for MOE test, so it's indicate that the conventional board is less strength from the coconut fibre board. As for water absorption test, the average water absorption of coconut fibre based panel board is less than conventional board. Overall, the coconut fibre board is better than conventional panel board because coconut fibre board are less swelling, has low water absorption, high modulus of rupture and low modulus of elasticity. Based on the finding, this coconut fibre panel board has potential as a stronger and long-lasting panel board than the conventional board in the market. Other than that, the panel also have their own aesthetic value since the recycled plastic bottle used as outer lining is colourful and giving aesthetic value.

Tests of star formation metrics in the low-metallicity galaxy NGC 5253 using ALMA observations of H30α line emission

NASA Astrophysics Data System (ADS)

Bendo, G. J.; Miura, R. E.; Espada, D.; Nakanishi, K.; Beswick, R. J.; D'Cruze, M. J.; Dickinson, C.; Fuller, G. A.

2017-11-01

We use Atacama Large Millimeter/submillimeter Array (ALMA) observations of H30α (231.90 GHz) emission from the low-metallicity dwarf galaxy NGC 5253 to measure the star formation rate (SFR) within the galaxy and to test the reliability of SFRs derived from other commonly used metrics. The H30α emission, which originates mainly from the central starburst, yields a photoionizing photon production rate of (1.9 ± 0.3) × 1052 s-1 and an SFR of 0.087 ± 0.013 M⊙ yr-1 based on conversions that account for the low metallicity of the galaxy and for stellar rotation. Among the other star formation metrics we examined, the SFR calculated from the total infrared flux was statistically equivalent to the values from the H30α data. The SFR based on a previously published version of the H α flux that was extinction corrected using Paα and Paβ lines was lower than but also statistically similar to the H30α value. The mid-infrared (22 μm) flux density and the composite star formation tracer based on H α and mid-infrared emission give SFRs that were significantly higher because the dust emission appears unusually hot compared to typical spiral galaxies. Conversely, the 70 and 160 μm flux densities yielded SFRs lower than the H30α value, although the SFRs from the 70 μm and H30α data were within 1σ-2σ of each other. While further analysis on a broader range of galaxies is needed, these results are instructive of the best and worst methods to use when measuring SFR in low-metallicity dwarf galaxies like NGC 5253.

Line defects on As2Se3-Chalcogenide photonic crystals for the design of all-optical power splitters and digital logic gates

NASA Astrophysics Data System (ADS)

Saghaei, Hamed; Zahedi, Abdulhamid; Karimzadeh, Rouhollah; Parandin, Fariborz

2017-10-01

In this paper, a triangular two-dimensional photonic crystal (PhC) of As2Se3-chalcogenide rods in air is presented and its photonic band diagram is calculated by plane wave method. In this structure, an optical waveguide is obtained by creating a line defect (eliminating rods) in diagonal direction of PhC. Numerical simulations based on finite difference time domain method show that when self-collimated beams undergo total internal reflection at the PhC-air interface, a total reflection of 90° occurs for the output beams. We also demonstrate that by decreasing the radius of As2Se3-chalcogenide instead of eliminating a diagonal line, a two-channel optical splitter will be designed. In this case, incoming self-collimated beams can be divided into the reflected and transmitted beams with arbitrary power ratio by adjusting the value of their radii. Based on these results, we propose a four-channel optical splitter using four line defects. The power ratio among output channels can be controlled systematically by varying the radius of rods in the line defects. We also demonstrate that by launching two optical sources with the same intensity and 90° phase difference from both perpendicular faces of the PhC, two logic OR and XOR gates will be achieved at the output channels. These optical devices have some applications in photonic integrated circuits for controlling and steering (managing) the light as desired.

Evaluation of helmet-mounted display targeting symbology based on eye tracking technology

NASA Astrophysics Data System (ADS)

Wang, Lijing; Wen, Fuzhen; Ma, Caixin; Zhao, Shengchu; Liu, Xiaodong

2014-06-01

The purpose of this paper is to find the Target Locator Lines (TLLs) which perform best by contrasting and comparing experiment based on three kinds of TTLs of fighter HMD. 10 university students, male, with an average age of 21-23, corrected visual acuity 1.5, participated in the experiment. In the experiment, head movement data was obtained by TrackIR. The geometric relationship between the coordinates of the real world and coordinates of the visual display was obtained by calculating the distance from viewpoint to midpoint of both eyes and the head movement data. Virtual helmet system simulation experiment environment was created by drawing TLLs of fighter HMD in the flight simulator visual scene. In the experiment, eye tracker was used to record the time and saccade trajectory. The results were evaluated by the duration of the time and saccade trajectory. The results showed that the symbol"locator line with digital vector length indication" cost most time and had the longest length of the saccade trajectory. It is the most ineffective and most unacceptable way. "Locator line with extending head vector length symbol" cost less time and had less length of the saccade trajectory. It is effective and acceptable;"Locator line with reflected vector length symbol" cost the least time and had the least length of the saccade trajectory. It is the most effective and most acceptable way. "Locator line with reflected vector length symbol" performs best. The results will provide reference value for the research of TTLs in future.

Supporting Worth Mapping with Sentence Completion

NASA Astrophysics Data System (ADS)

Cockton, Gilbert; Kujala, Sari; Nurkka, Piia; Hölttä, Taneli

Expectations for design and evaluation approaches are set by the development practices within which they are used. Worth-Centred Development (WCD) seeks to both shape and fit such practices. We report a study that combined two WCD approaches. Sentence completion gathered credible quantitative data on user values, which were used to identify relevant values and aversions of two player groups for an on-line gambling site. These values provided human value elements for a complementary WCD approach of worth mapping. Initial worth maps were extended in three workshops, which focused on outcomes and user experiences that could be better addressed in the current product and associated marketing materials. We describe how worth maps were prepared for, and presented in, workshops, and how product owners and associated business roles evaluated the combination of WCD approaches. Based on our experiences, we offer practical advice on this combinination.

Measurements of pressure-broadening coefficients of NO and O3 using a computerized tunable diode laser spectrometer

NASA Technical Reports Server (NTRS)

Lundqvist, S.; Margolis, J.; Reid, J.

1982-01-01

Foreign-gas broadening coefficients have been measured for selected lines of ozone in the 9.2 micron region and for several R-branch lines of nitric oxide in the 5.4 micron region using a computerized tunable diode laser spectrometer. The data analysis showed the importance of fitting a Lorentzian line shape out to several times the halfwidth to obtain a correct value of the broadening coefficient. The measured broadening coefficients of nitric oxide were in good agreement with those obtained by Abels and Shaw (1966). The results of the analysis of eleven lines in the v-1 band and five lines in the v-3 band of ozone show a transition-dependent broadening coefficient. The average value of the foreign-gas broadening ceofficients for the measured v-1 and v-3 lines are 0.075 and 0.073 per cm per atm, respectively.

Depreciating and stating the value of hospital buildings what you need to know.

PubMed

Holmes, John R; Felsenthal, David

2009-10-01

Healthcare financial executives of not-for-profit hospitals may be overdepreciating and understating the value of the hospital building on their financial statements. Changing the remaining lives of assets and their depreciation will help enhance the bottom line for many organizations. Ensuring that they are correctly stating the investment value of their assets is one way CFOs can have a positive impact on their organization's bottom line in a tough economy.

Measurements of Band Intensities, Herman-Wallis Parameters, and Self-Broadening Line-Widths of the 30011 - 00001 and 30014 - 00001 Bands of CO2 at 6503 cm(exp -1) and 6076 cm(exp -1)

NASA Technical Reports Server (NTRS)

Giver, L. P.; Brown, L. R.; Wattson, R. B.; Spencer, M. N.; Chackerian, C., Jr.; Strawa, Anthony W. (Technical Monitor)

1995-01-01

Rotationless band intensities and Herman-Wallis parameters are listed in HITRAN tabulations for several hundred CO2 overtone-combination bands. These parameters are based on laboratory measurements when available, and on DND calculations for the unmeasured bands. The DND calculations for the Fermi interacting nv(sub 1) + v(sub 3) polyads show the a(sub 2) Herman-Wallis parameter varying smoothly from a negative value for the first member of the polyad to a positive value for the final member. Measurements of the v(sub 1) + v(sub 3) dyad are consistent with the DND calculations for the a(sub 2) parameter, as are our recent measurements of the 4v(sub 1) + v(sub 3) pentad. However, the measurement-based values in the HITRAN tables for the 2v(sub 1) + v(sub 3) triad and the 3v(sub 1) + v(sub 3) tetrad do not support the DND calculated values for the a(sub 2) parameters. We therefore decided to make new measurements to improve some of these intensity parameters. With the McMath FTS at Kitt Peak National Observatory/National Solar Observatory we recorded several spectra of the. 4000 to 8000 cm(exp -1) region of pure CO2 at 0.011 cm(exp -1) resolution using the 6 meter White absorption cell. The signal/noise and absorbance of the first and fourth bands of the 3v(sub 1) + v(sub 3) tetrad of C-12O-16 were ideal on these spectra for measuring line intensities and broadening widths. Our selfbroadening results agree with the HITRAN parameterization, while our measurements of the rotationless band intensities are about 15% less than the HITRAN values. We find a negative value of a(sub 2) for the 30011-00001 band and a positive value for the 30014-00001 band, whereas the HITRAN values of a(sub 2) are positive for all four tetrad bands. Our a(sub 1) and a(sub 2) Herman-Wallis parameters are closer to DND calculated values than the 1992 HITRAN values for both the 30011-00001 and the 30014-00001 band.

What is the benefit of treatment with multiple lines of chemotherapy for patients with metastatic breast cancer? A retrospective cohort study.

PubMed

Bakker, J L; Wever, K; van Waesberghe, J H; Beeker, A; Meijers-Heijboer, H; Konings, I R; Verheul, H M W

2015-12-01

Despite the extensive clinical experience, it is still under debate to what extent patients with metastatic breast cancer (MBC) benefit from multiple lines of chemotherapy beyond standard first or second line treatment. Selection of patients with MBC who will benefit from treatment is crucial to improve outcome and reduce unnecessary toxicity. In this retrospective study, systemic treatment outcome for patients with metastatic MBC is being evaluated. We evaluated to what extent the clinical benefit of prior chemotherapy can predict the success of a subsequent treatment line. Ninety-one patients treated with chemotherapy for MBC between January 2005 and January 2009 were included in this study. Clinical characteristics of patients, choices of chemotherapy and response at first evaluation of every treatment line was evaluated based on radiologic and clinical data. Patients received multiple systemic cytotoxic and biological (combination) therapies. 30% of these patients received more than five consecutive systemic (combination) treatments. First line chemotherapy was mostly anthracycline-based, followed by taxanes, capecitabine and vinorelbine. The response rate (RR, complete response plus partial response according to RECIST 1.1) decreased from 20% (95% CI 11-28%) upon first line of treatment to 0% upon the fourth line. The clinical benefit rate (combining RR and stable disease) decreased from 85% (95% CI 78-93%) in the first to 54% (95% CI 26-67) upon the fourth line. 24% of the patients with clinical benefit at first evaluation did not receive a subsequent line of treatment when progressive disease occurred, while sixty-one percent of the patients with progressive disease at first evaluation of a treatment did not receive a subsequent line of chemotherapy. When applied, the efficacy of a subsequent line of treatment was similar for patients independent of previous treatment benefit. The clinical benefit at first evaluation from systemic treatment in MBC does not predict for subsequent treatment benefit in this retrospective analysis. The fact that 61% of patients did not receive subsequent treatment after previous treatment failure suggests that either clinical judgement is of critical value in selection of patients to prevent them from unnecessary toxicity or, alternatively indicates that based on the assumption that prior treatment failure predicts for lack of benefit undertreatment of patients occurs. Therefore, a more adequate clinical judgement tool or predictive biomarkers for response are urgently needed to improve treatment outcome. Copyright © 2015. Published by Elsevier Ltd.

On the application of cw external cavity quantum cascade infrared lasers for plasma diagnostics

NASA Astrophysics Data System (ADS)

Lopatik, D.; Lang, N.; Macherius, U.; Zimmermann, H.; Röpcke, J.

2012-11-01

Three continuous wave external cavity quantum cascade lasers (EC-QCLs) operating between 1305 and 2260 cm-1 (4.42-7.66 µm) have been tested as radiation sources for an absorption spectrometer focused on the analysis of physical and chemical phenomena in molecular plasmas. Based on the wide spectral tunability of EC-QCLs, multiple species detection has become feasible and is demonstrated in a study of low-pressure Ar/N2 microwave plasmas containing methane as a hydrocarbon precursor. Using the direct absorption technique, the evolution of the concentrations of CH4, C2H2, HCN and H2O has been monitored depending on the discharge conditions at a pressure of p = 0.5 mbar and at a frequency of f = 2.45 GHz in a planar microwave plasma reactor. The concentrations were found to be in the range of 1011-1014 molecules cm-3. In addition, based on the analysis of the line profile of selected absorption lines, the gas temperature Tg has been calculated in dependence on the discharge power. Tg increased with the power values and was in the range between 400 and 700 K. Further, in a pure He/Ar microwave plasma, the wavelength modulation spectroscopy technique has been applied for the sensitive detection of transient plasma species with absorbencies down to 10-5. The typical spectral line width of an EC-QCL under the study was found to be in the range 24 to 38 MHz depending (i) on the chopping technique used and (ii) on a single or averaged measurement approach. Further, different methods for the modulation and tuning of the laser radiation have been tested. Varying the power values of an EC-QCL between 0.1 and 154 mW for direct absorption measurements under low pressure conditions, no saturation effects in determining the concentrations of methane, acetylene and carbon monoxide could be found under the experimental conditions used, i.e. for lines with line strengths between 10-19 and 10-22 cm molecule-1.

Genomic selection in sugar beet breeding populations

PubMed Central

2013-01-01

Background Genomic selection exploits dense genome-wide marker data to predict breeding values. In this study we used a large sugar beet population of 924 lines representing different germplasm types present in breeding populations: unselected segregating families and diverse lines from more advanced stages of selection. All lines have been intensively phenotyped in multi-location field trials for six agronomically important traits and genotyped with 677 SNP markers. Results We used ridge regression best linear unbiased prediction in combination with fivefold cross-validation and obtained high prediction accuracies for all except one trait. In addition, we investigated whether a calibration developed based on a training population composed of diverse lines is suited to predict the phenotypic performance within families. Our results show that the prediction accuracy is lower than that obtained within the diverse set of lines, but comparable to that obtained by cross-validation within the respective families. Conclusions The results presented in this study suggest that a training population derived from intensively phenotyped and genotyped diverse lines from a breeding program does hold potential to build up robust calibration models for genomic selection. Taken together, our results indicate that genomic selection is a valuable tool and can thus complement the genomics toolbox in sugar beet breeding. PMID:24047500

Equivalent formulations of the Riemann hypothesis based on lines of constant phase

NASA Astrophysics Data System (ADS)

Schleich, W. P.; Bezděková, I.; Kim, M. B.; Abbott, P. C.; Maier, H.; Montgomery, H. L.; Neuberger, J. W.

2018-06-01

We prove the equivalence of three formulations of the Riemann hypothesis for functions f defined by the four assumptions: (a 1) f satisfies the functional equation f(1 ‑ s) = f(s) for the complex argument s ≡ σ + iτ, (a2) f is free of any pole, (a3) for large positive values of σ the phase θ of f increases in a monotonic way without a bound as τ increases, and (a4) the zeros of f as well as of the first derivative f ‧ of f are simple zeros. The three equivalent formulations are: (R1) All zeros of f are located on the critical line σ = 1/2, (R2) All lines of constant phase of f corresponding to +/- π ,+/- 2π ,+/- 3π , ... merge with the critical line, and (R3) All points where f ‧ vanishes are located on the critical line, and the phases of f at two consecutive zeros of f ‧ differ by π. Our proof relies on the topology of the lines of constant phase of f dictated by complex analysis and the assumptions (a1)–(a4). Moreover, we show that (R2) implies (R1) even in the absence of (a4). In this case (a4) is a consequence of (R2).

Modeling power flow in the induction cavity with a two dimensional circuit simulation

NASA Astrophysics Data System (ADS)

Guo, Fan; Zou, Wenkang; Gong, Boyi; Jiang, Jihao; Chen, Lin; Wang, Meng; Xie, Weiping

2017-02-01

We have proposed a two dimensional (2D) circuit model of induction cavity. The oil elbow and azimuthal transmission line are modeled with one dimensional transmission line elements, while 2D transmission line elements are employed to represent the regions inward the azimuthal transmission line. The voltage waveforms obtained by 2D circuit simulation and transient electromagnetic simulation are compared, which shows satisfactory agreement. The influence of impedance mismatch on the power flow condition in the induction cavity is investigated with this 2D circuit model. The simulation results indicate that the peak value of load voltage approaches the maximum if the azimuthal transmission line roughly matches the pulse forming section. The amplitude of output transmission line voltage is strongly influenced by its impedance, but the peak value of load voltage is insensitive to the actual output transmission line impedance. When the load impedance raises, the voltage across the dummy load increases, and the pulse duration at the oil elbow inlet and insulator stack regions also slightly increase.

A counting-weighted calibration method for a field-programmable-gate-array-based time-to-digital converter

NASA Astrophysics Data System (ADS)

Chen, Yuan-Ho

2017-05-01

In this work, we propose a counting-weighted calibration method for field-programmable-gate-array (FPGA)-based time-to-digital converter (TDC) to provide non-linearity calibration for use in positron emission tomography (PET) scanners. To deal with the non-linearity in FPGA, we developed a counting-weighted delay line (CWD) to count the delay time of the delay cells in the TDC in order to reduce the differential non-linearity (DNL) values based on code density counts. The performance of the proposed CWD-TDC with regard to linearity far exceeds that of TDC with a traditional tapped delay line (TDL) architecture, without the need for nonlinearity calibration. When implemented in a Xilinx Vertix-5 FPGA device, the proposed CWD-TDC achieved time resolution of 60 ps with integral non-linearity (INL) and DNL of [-0.54, 0.24] and [-0.66, 0.65] least-significant-bit (LSB), respectively. This is a clear indication of the suitability of the proposed FPGA-based CWD-TDC for use in PET scanners.

Synthesis of 2',4-dihydroxy-3-methoxychalcone and 2',4',4-trihydroxy-3-methoxychalcone as a candidate anticancer against cervical (WiDr), colon (HeLa), and breast (T47d) cancer cell lines in vitro

NASA Astrophysics Data System (ADS)

Matsjeh, Sabirin; Swasono, Respati Tri; Anwar, Chairil; Solikhah, Eti Nurwening; Lestari, Endang

2017-03-01

The compound 2',4-dihydroxy-3-methoxychalcone and 2',4',4-trihydroxy-3-methoxychalcone have been synthesized through Claisen-Schmidt reaction from 2-hydroxyacetophenone and 2,4-dihydroxyacetophenone with 4-hydroxy-3-methoxy benzaldehida (vanillin) in aqueous KOH 40% and KSF montmorillonite as catalyst in methanol. All these products were characterized by FT-IR, TLC Scanner, GC-MS, MS-Direct, and 1H-NMR and 13C-NMR spectrometer. Both of these compounds were tested citotoxycity activity as an anticancer against cervical, colon, and breast cancer cells (Hela, WiDr, and T47D cell lines) using MTT assay in vitro. Dose series given test solution concentration on Hela, WiDr, and T47D cells started from 6,25; 25; 50 and 100 µg/mL with incubation treatment for 24 hours. The result of study showed that the 2',4-dihydroxy-3-methoxychalcone as bright yellow crystal with the melting point of 114-115 °C and the yield of 13.77% and the 2',4',4-trihydroxy-3-methoxychalcone as bright yellow crystals with the melting point of 195-197 °C and the yield of 6%. Other 2',4-dihydroxy-3-methoxychalcone and 2',4',4-trihydroxy-3-methoxychalcone also exhibited cytotoxic activity against the cancer cell lines, with the 2',4',4-trihydroxy-3-methoxychalcone showed greater activities than the 2',4-dihydroxy-3-methoxychalcone in WiDr cell lines. The 2',4-dihydroxy-3-methoxychalcone and 2',4',4-trihydroxy-3-methoxychalcone exhibited strong anticancer activities with IC50 value below 20 µg/mL. The activity of 2',4',4-trihydroxy-3-methoxychalcone showed the most active against Hela and WiDr cell lines with IC50 value 8.53 and 2.66 µg/mL respectively, than T47D cell lines with IC50 value 24.61 µg/mL. The test results cytotoxic of 2',4-dihydroxy-3-methoxychalcone showed the most active against Hela and WiDr cell lines with IC50 value 12.80, 19.57 µg/mL than T47D cell lines with IC50 value of 20.73 µg/mL. IC50 value indicated that 2',4-dihydroxy-3-methoxychalcone and 2',4',4-trihydroxy-3-methoxychalcone potential as inhibitors in Hela, WiDr and T47D cell lines.

Design and Construction of a Microcontroller-Based Ventilator Synchronized with Pulse Oximeter.

PubMed

Gölcük, Adem; Işık, Hakan; Güler, İnan

2016-07-01

This study aims to introduce a novel device with which mechanical ventilator and pulse oximeter work in synchronization. Serial communication technique was used to enable communication between the pulse oximeter and the ventilator. The SpO2 value and the pulse rate read on the pulse oximeter were transmitted to the mechanical ventilator through transmitter (Tx) and receiver (Rx) lines. The fuzzy-logic-based software developed for the mechanical ventilator interprets these values and calculates the percentage of oxygen (FiO2) and Positive End-Expiratory Pressure (PEEP) to be delivered to the patient. The fuzzy-logic-based software was developed to check the changing medical states of patients and to produce new results (FiO2 ve PEEP) according to each new state. FiO2 and PEEP values delivered from the ventilator to the patient can be calculated in this way without requiring any arterial blood gas analysis. Our experiments and the feedbacks from physicians show that this device makes it possible to obtain more successful results when compared to the current practices.

Divergent selection on 63-day body weight in the rabbit: response on growth, carcass and muscle traits

PubMed Central

Larzul, Catherine; Gondret, Florence; Combes, Sylvie; de Rochambeau, Hubert

2005-01-01

The effects of selection for growth rate on weights and qualitative carcass and muscle traits were assessed by comparing two lines selected for live body weight at 63 days of age and a cryopreserved control population raised contemporaneously with generation 5 selected rabbits. The animals were divergently selected for five generations for either a high (H line) or a low (L line) body weight, based on their BLUP breeding value. Heritability (h2) was 0.22 for 63-d body weight (N = 4754). Growth performance and quantitative carcass traits in the C group were intermediate between the H and L lines (N = 390). Perirenal fat proportion (h2 = 0.64) and dressing out percentage (h2 = 0.55) ranked in the order L < H = C (from high to low). The weight and cross-sectional area of the Semitendinosus muscle, and the mean diameter of the constitutive myofibres were reduced in the L line only (N = 140). In the Longissimus muscle (N = 180), the ultimate pH (h2 = 0.16) and the maximum shear force reached in the Warner-Braztler test (h2 = 0.57) were slightly modified by selection. PMID:15588570

Enhancement of breast periphery region in digital mammography

NASA Astrophysics Data System (ADS)

Menegatti Pavan, Ana Luiza; Vacavant, Antoine; Petean Trindade, Andre; Quini, Caio Cesar; Rodrigues de Pina, Diana

2018-03-01

Volumetric breast density has been shown to be one of the strongest risk factor for breast cancer diagnosis. This metric can be estimated using digital mammograms. During mammography acquisition, breast is compressed and part of it loses contact with the paddle, resulting in an uncompressed region in periphery with thickness variation. Therefore, reliable density estimation in the breast periphery region is a problem, which affects the accuracy of volumetric breast density measurement. The aim of this study was to enhance breast periphery to solve the problem of thickness variation. Herein, we present an automatic algorithm to correct breast periphery thickness without changing pixel value from internal breast region. The correction pixel values from periphery was based on mean values over iso-distance lines from the breast skin-line using only adipose tissue information. The algorithm detects automatically the periphery region where thickness should be corrected. A correction factor was applied in breast periphery image to enhance the region. We also compare our contribution with two other algorithms from state-of-the-art, and we show its accuracy by means of different quality measures. Experienced radiologists subjectively evaluated resulting images from the tree methods in relation to original mammogram. The mean pixel value, skewness and kurtosis from histogram of the three methods were used as comparison metric. As a result, the methodology presented herein showed to be a good approach to be performed before calculating volumetric breast density.

The awakening of Attneave's sleeping cat: identification of everyday objects on the basis of straight-line versions of outlines.

PubMed

De Winter, Joeri; Wagemans, Johan

2008-01-01

Attneave (1954 Psychological Review 61 183-193) demonstrated that a line drawing of a sleeping cat can still be identified when the smoothly curved contours are replaced by straight-line segments connecting the positive maxima and negative minima of contour curvature. Using the set of line drawings by Snodgrass and Vanderwart (1980 Journal of Experimental Psychology: Human Learning and Memory 6 174-215) we made outline versions (with known curvature values along the contour) that can still be identified and that can be used to test Attneave's demonstration more systematically and more thoroughly. In five experiments (with 444 subjects in total), we tested identifiability of straight-line versions of 184 stimuli with different selections of points to be connected (using 24 to 28 subjects per stimulus per condition). Straight-line versions connecting curvature extrema were easier to identify than those based on inflections (where curvature changes sign), and those connecting salient points (determined by 161 independent subjects) were easier than those connecting midpoints. However, identification varied considerably between objects: some were almost always identifiable and others almost never, regardless of the selection criterion, whereas identifiability depended on the specific shape attributes preserved in the straight-line version of the outline in other objects. Results are discussed in relation to Attneave's original hypotheses as well as in the light of more recent theories on shape perception and object identification.

Effect of Seepage on Change in Stress Distribution Scenario in Static and Seismic Behaviour of Earthen Dams

NASA Astrophysics Data System (ADS)

Nandi, N.; Chowdhury, Roy; Dutta, S. C.

2018-02-01

The present study makes an effort to understand the damage of earthen dams under static and seismic loading condition. To make the investigation more realistic, behaviour of earthen dams considering the occurrence of a phreatic line indicating the submerged zone due to seepage within the dam body is considered. In case of earthen dams, homogeneous or nonhomogeneous, the consideration of the occurrence of a phreatic line or seepage line through the dam body is an important part of the earthen dam design methodology. The impervious material properties in the submerged zone below the phreatic line due to seepage may differ a lot in magnitudes as compared to the value of the same materials lying above this line. Hence, to have the exact stress distribution scenarios within the earthen dam, the different material properties above and below the phreatic line are considered in this present study. The study is first carried out by two-dimensional as well as three-dimensional finite element analysis under static loading condition. The work is further extended to observe the effect of seepage due to the consideration of the phreatic line on dynamic characteristics of earthen dams. Free vibration analysis and seismic analysis based on the Complete Quadratic Combination (CQC) method by considering twodimensional and three-dimensional modeling are carried out to present the frequencies, mode shapes and the stress distribution pattern of the earthen dam.

Linking ecophysiological modelling with quantitative genetics to support marker-assisted crop design for improved yields of rice (Oryza sativa) under drought stress

PubMed Central

Gu, Junfei; Yin, Xinyou; Zhang, Chengwei; Wang, Huaqi; Struik, Paul C.

2014-01-01

Background and Aims Genetic markers can be used in combination with ecophysiological crop models to predict the performance of genotypes. Crop models can estimate the contribution of individual markers to crop performance in given environments. The objectives of this study were to explore the use of crop models to design markers and virtual ideotypes for improving yields of rice (Oryza sativa) under drought stress. Methods Using the model GECROS, crop yield was dissected into seven easily measured parameters. Loci for these parameters were identified for a rice population of 94 introgression lines (ILs) derived from two parents differing in drought tolerance. Marker-based values of ILs for each of these parameters were estimated from additive allele effects of the loci, and were fed to the model in order to simulate yields of the ILs grown under well-watered and drought conditions and in order to design virtual ideotypes for those conditions. Key Results To account for genotypic yield differences, it was necessary to parameterize the model for differences in an additional trait ‘total crop nitrogen uptake’ (Nmax) among the ILs. Genetic variation in Nmax had the most significant effect on yield; five other parameters also significantly influenced yield, but seed weight and leaf photosynthesis did not. Using the marker-based parameter values, GECROS also simulated yield variation among 251 recombinant inbred lines of the same parents. The model-based dissection approach detected more markers than the analysis using only yield per se. Model-based sensitivity analysis ranked all markers for their importance in determining yield differences among the ILs. Virtual ideotypes based on markers identified by modelling had 10–36 % more yield than those based on markers for yield per se. Conclusions This study outlines a genotype-to-phenotype approach that exploits the potential value of marker-based crop modelling in developing new plant types with high yields. The approach can provide more markers for selection programmes for specific environments whilst also allowing for prioritization. Crop modelling is thus a powerful tool for marker design for improved rice yields and for ideotyping under contrasting conditions. PMID:24984712

Training Providers and Patients to Talk about End-of-Life Care

Cancer.gov

Failing to discuss the transition from active cancer treatment to end-of-life care can leave doctors unsure of what a patient truly wants. Failing to receive end-of-life care in line with their values and wishes can cause patients and their families great distress. Researchers have developed innovative, evidence-based programs to help doctors and patients improve their communication skills and grow comfortable with these discussions.

Scratch Your Brain Where It Itches: Math Games, Tricks and Quick Activities, Book A-1.

ERIC Educational Resources Information Center

Brumbaugh, Linda

This resource book contains mathematical games, tricks, and quick activities for the classroom. Categories include place value, number lines, basic facts and computation, computation and calculator practice, puzzles for tricky thinkers, and geometry. Ten classroom games and activities are found in the place value and number line sections, 27…

Extending the application of deuterium excess as a tracer in surface and groundwaters

NASA Astrophysics Data System (ADS)

Hurst, S.; Krishnamurthy, R. V.

2017-12-01

Stable isotopes of surface and ground waters provide invaluable information on the processes involved in their genesis. A starting point in these applications is the relationship between hydrogen (δ2H) and oxygen (δ18O), exemplified in the so-called Global Meteoric Water Line where δ2H=8δ18O+10 [1]. From this line Dansgaard [2] defined the parameter deuterium excess where d=δ2H-8δ18O. Generally, the d-excess value is fixed at the source, predominantly the equatorial oceans and retained. At an average humidity of about 85% the expected d-excess value is 10. Deviations indicate secondary changes in the air mass or a water body thus making d-excess a useful geophysical tracer. For instance, evaporation results in a higher d-excess in the vapor. Mixing of this water vapor with overhead air mass results in precipitation exhibiting d-excess values higher than Global Meteoric Water Line [3]. Alternatively, the fraction of liquid remaining will have low d-excess and in extreme cases negative d-excess. In this case a plot of d-excess-δ2H will give a straight line with a negative slope. This can be demonstrated from pan evaporation experiments [4]. Deviation from a perfect straight line on the d-excess-δ2H plot indicates a combination of mixing from various source waters and evaporation. This study will discuss various case studies from multiple environments applying this approach using d-excess. References [1] Craig, H. Standard for Reporting Concentrations of Deuterium and Oxygen-18 in Natural Waters. Science 133, 1833-1834 (1961). [2] Dansgaard, W. Stable isotopes in precipitation. Tellus A 16: 436-468 (1964). [3] Machavaram, M. &, Krishnamurthy, R.V. Earth surface evaporative process: a case study from the Great Lakes region of the United States based on deuterium excess in precipitation. Geochim. et Cosmochem. Acta 59, 4279-4283 (1995). [4] Simpson, H.J., Hamza, M.S., & White, J.W.C. Evaporative enrichment of deuterium and 18O in arid zone irrigation. IAEA, 241-256 (1987).

Efectos Especiales de Anclaje (Estudio sobre Regresiones de Juicios Condicionales). Parte 2: Invariancia del Juicio No-Condicional Como Valor Estandar Para el Juicio Condicional (Special Effects of Anchoring (Study of Regression of Conditional Judgements) Part 2: Invariance of Unconditional Judgments as Standard Value for the Conditional Judgment). Publication No. 31.

ERIC Educational Resources Information Center

Lopez Alonso, A. O.

From the best-fit lines corresponding to sets of families of conditional judgements, the constant stimulus family and the constant condition family, both defined for a same scale object, the coordinate values of the point of intersection of both lines (indifference point) are obtained. These values are studied in relation to the mean values of the…

Lunar-edge based on-orbit modulation transfer function (MTF) measurement

NASA Astrophysics Data System (ADS)

Cheng, Ying; Yi, Hongwei; Liu, Xinlong

2017-10-01

Modulation transfer function (MTF) is an important parameter for image quality evaluation of on-orbit optical image systems. Various methods have been proposed to determine the MTF of an imaging system which are based on images containing point, pulse and edge features. In this paper, the edge of the moon can be used as a high contrast target to measure on-orbit MTF of image systems based on knife-edge methods. The proposed method is an extension of the ISO 12233 Slanted-edge Spatial Frequency Response test, except that the shape of the edge is a circular arc instead of a straight line. In order to get more accurate edge locations and then obtain a more authentic edge spread function (ESF), we choose circular fitting method based on least square to fit lunar edge in sub-pixel edge detection process. At last, simulation results show that the MTF value at Nyquist frequency calculated using our lunar edge method is reliable and accurate with error less than 2% comparing with theoretical MTF value.

Design, synthesis and anti-tumor activity study of novel histone deacetylase inhibitors containing isatin-based caps and o-phenylenediamine-based zinc binding groups.

PubMed

Gao, Shuai; Zang, Jie; Gao, Qianwen; Liang, Xuewu; Ding, Qinge; Li, Xiaoyang; Xu, Wenfang; Chou, C James; Zhang, Yingjie

2017-06-15

As a hot topic of epigenetic studies, histone deacetylases (HDACs) are related to lots of diseases, especially cancer. Further researches indicated that different HDAC isoforms played various roles in a wide range of tumor types. Herein a novel series of HDAC inhibitors with isatin-based caps and o-phenylenediamine-based zinc binding groups have been designed and synthesized through scaffold hopping strategy. Among these compounds, the most potent compound 9n exhibited similar if not better HDAC inhibition and antiproliferative activities against multiple tumor cell lines compared with the positive control entinostat (MS-275). Additionally, compared with MS-275 (IC 50 values for HDAC1, 2 and 3 were 0.163, 0.396 and 0.605µM, respectively), compound 9n with IC 50 values of 0.032, 0.256 and 0.311µM for HDAC1, 2 and 3 respectively, showed a moderate HDAC1 selectivity. Copyright © 2017. Published by Elsevier Ltd.

Circumnuclear Multi-phase Gas in the Circinus Galaxy. I. Non-LTE Calculations of CO Lines

NASA Astrophysics Data System (ADS)

Wada, Keiichi; Fukushige, Ryosuke; Izumi, Takuma; Tomisaka, Kohji

2018-01-01

In this study, we investigate the line emissions from cold molecular gas based on our previous “radiation-driven fountain model,” which reliably explains the spectral energy distribution of the nearest type 2 Seyfert galaxy, the Circinus galaxy. Using a snapshot of the best-fit radiation-hydrodynamic model for the central r≤slant 16 pc, in which non-equilibrium X-ray-dominated region chemistry is solved, we conduct post-processed non-local thermodynamic equilibrium radiation transfer simulations for the CO lines. We obtain a spectral line energy distribution with a peak around J≃ 6, and its distribution suggests that the lines are not thermalized. However, for a given line of sight, the optical depth distribution is highly non-uniform between {τ }ν \\ll 1 and {τ }ν \\gg 1. The CO-to-H2 conversion factor ({X}{CO}), which can be directly obtained from the results and is not a constant, depends strongly on the integrated intensity and differs from the fiducial value for local objects. {X}{CO} exhibits a large dispersion of more than one order of magnitude, reflecting the non-uniform internal structure of a “torus.” In addition, we found that the physical conditions differ between grid cells on a scale of a few parsecs along the observed lines of sight; therefore, a specific observed line ratio does not necessarily represent a single physical state of the interstellar medium.

Relationship Between the Electromagnetic Wave Energy Coupled by Overhead Lines and the Radiation Source Current Explored in the Laboratory

NASA Astrophysics Data System (ADS)

Li, Xiangchao; Wan, Zhicheng

2018-04-01

In order to solve the damage and interference problems to the electronic devices, which are induced by overvoltage excited by the coupling process between lightning electromagnetic wave and overhead lines, the lightning channel is set to be equivalent to a radiant wire antenna. Based on the integration model of lightning return stroke channel, transmission line, and ground, we take advantage of the derived formula gotten from the transmission line model. By combing the theoretical and experimental methods, we conduct a comparative analysis on the coupling process between natural/simulated lightning and overhead line. Besides, we also calculate the amplitude and energy of overvoltage, which is caused by the coupling process between lightning electromagnetic wave and overhead lines. Upon these experimental results, we can draw several conclusions as follows: when the amplitude of the lightning current in the channel is between 5 kA and 41 kA, it takes on an excellent linear relation between the amplitude of overvoltage and the magnitude of the lightning current, the relation between coupling energy and magnitude of the lightning current takes on an exponential trend. When lightning wave transmits on the transmission lines, the high-order mode will be excited. Through analysis on the high-order mode's characteristics, we find that the theoretical analysis is consistent with the experimental results, which has a certain reference value to the protection on overhead lines.

Eco-friendly synthesis, in vitro anti-proliferative evaluation, and 3D-QSAR analysis of a novel series of monocationic 2-aryl/heteroaryl-substituted 6-(2-imidazolinyl)benzothiazole mesylates.

PubMed

Racané, Livio; Ptiček, Lucija; Sedić, Mirela; Grbčić, Petra; Kraljević Pavelić, Sandra; Bertoša, Branimir; Sović, Irena; Karminski-Zamola, Grace

2018-04-17

Herein, we describe the synthesis of twenty-one novel water-soluble monocationic 2-aryl/heteroaryl-substituted 6-(2-imidazolinyl)benzothiazole mesylates 3a-3u and present the results of their anti-proliferative assays. Efficient syntheses were achieved by three complementary simple two-step synthetic protocols based on the condensation reaction of aryl/heteroaryl carbaldehydes or carboxylic acid. We developed an eco-friendly synthetic protocol using glycerol as green solvent, particularly appropriate for the condensation of thermally and acid-sensitive heterocycles such as furan, benzofuran, pyrrole, and indole. Screening of anti-proliferative activity was performed on four human tumour cell lines in vitro including pancreatic cancer (CFPAC-1), metastatic colon cancer (SW620), hepatocellular carcinoma (HepG2), and cervical cancer (HeLa), as well as in normal human fibroblast cell lines. All tested compounds showed strong to moderate anti-proliferative activity on tested cell lines depending on the structure containing aryl/heteroaryl moiety coupled to 6-(2-imidazolinyl)benzothiazole moiety. The most potent cytostatic effects on all tested cell lines with [Formula: see text] values ranging from 0.1 to 3.70 [Formula: see text] were observed for benzothiazoles substituted with naphthalene-2-yl 3c, benzofuran-2-yl 3e, indole-3-yl 3j, indole-2-yl 3k, quinoline-2-yl 3s, and quinoline-3-yl 3t and derivatives substituted with phenyl 3a, naphthalene-1-yl 3b, benzothiazole-2-yl 3g, benzothiazole-6-yl 3h, N-methylindole-3-yl 3l, benzimidazole-2-yl 3n, benzimidazole-5(6)-yl 3o, and quinolone-4-yl 3u with [Formula: see text] values ranging from 1.1 to 29.1 [Formula: see text]. Based on obtained anti-proliferative activities, 3D-QSAR models for five cell lines were derived. Molecular volume, molecular surface, the sum of hydrophobic surface areas, molecular mass, and possibility of making dispersion forces were identified by QSAR analyses as molecular properties that are positively correlated with anti-proliferative activity, while compound's capability to accept H-bond was identified as a negatively correlated property. Comparison of molecular properties identified for different cell lines enabled assumptions about similarity of mode of action through which anti-proliferative activities against different cell lines are accomplished. Novel compounds that are predicted to have enhanced activities in comparison with herein presented ones were designed using 3D-QSAR analysis as guideline.

Generally applicable fed-batch culture concept based on the detection of metabolic state by on-line balancing.

PubMed

Jobé, Anna Marya; Herwig, Christoph; Surzyn, Martin; Walker, Bernhard; Marison, Ian; von Stockar, Urs

2003-06-20

In many microorganisms, flux limitations in oxidative metabolism lead to the formation of overflow metabolites even under fully aerobic conditions. This can be avoided if the specific growth rate is controlled at a low enough value. This is usually accomplished by controlling the substrate feeding profile in a fed-batch process. The present work proposes a control concept which is based on the on-line detection of metabolic state by on-line calculation of mass and elemental balances. The advantages of this method are: 1) the check of measurement consistency based on all of the available measurements, 2) the minimum requirement of a priori knowledge of metabolism, and 3) the exclusive use of simple and established on-line techniques which do not require direct measurement of the metabolite in question. The control concept has been linked to a simple adaptive controller and applied to fed-batch cultures of S. cerevisiae and E. coli, organisms which express different overflow metabolites, ethanol and acetic acid, respectively. Oxidative and oxidoreductive states of S. cerevisiae and E. coli cultures were detected with high precision. As demonstrated by the formation of acetic acid in E. coli cultures, metabolic states could be correctly distinguished for systems for which traditional methods, such as respiratory quotient (RQ), are insensitive. Hence, it could be shown that the control concept allowed avoidance of overflow metabolite formation and operation at maximum oxidative biomass productivity and oxidative conversion of substrate into biomass. Based on mass and elemental balances, the proposed method additionally provides a richness of additional information, such as yield coefficients and estimation of concentrations and specific conversion rates. These data certainly help the operator to additionally evaluate the state of the process on-line. Copyright 2003 Wiley Periodicals, Inc. Biotechnol Bioeng 82: 627-639, 2003.

Improved Seam-Line Searching Algorithm for UAV Image Mosaic with Optical Flow

PubMed Central

Zhang, Weilong; Guo, Bingxuan; Liao, Xuan; Li, Wenzhuo

2018-01-01

Ghosting and seams are two major challenges in creating unmanned aerial vehicle (UAV) image mosaic. In response to these problems, this paper proposes an improved method for UAV image seam-line searching. First, an image matching algorithm is used to extract and match the features of adjacent images, so that they can be transformed into the same coordinate system. Then, the gray scale difference, the gradient minimum, and the optical flow value of pixels in adjacent image overlapped area in a neighborhood are calculated, which can be applied to creating an energy function for seam-line searching. Based on that, an improved dynamic programming algorithm is proposed to search the optimal seam-lines to complete the UAV image mosaic. This algorithm adopts a more adaptive energy aggregation and traversal strategy, which can find a more ideal splicing path for adjacent UAV images and avoid the ground objects better. The experimental results show that the proposed method can effectively solve the problems of ghosting and seams in the panoramic UAV images. PMID:29659526

Threat evaluation for impact assessment in situation analysis systems

NASA Astrophysics Data System (ADS)

Roy, Jean; Paradis, Stephane; Allouche, Mohamad

2002-07-01

Situation analysis is defined as a process, the examination of a situation, its elements, and their relations, to provide and maintain a product, i.e., a state of situation awareness, for the decision maker. Data fusion is a key enabler to meeting the demanding requirements of military situation analysis support systems. According to the data fusion model maintained by the Joint Directors of Laboratories' Data Fusion Group, impact assessment estimates the effects on situations of planned or estimated/predicted actions by the participants, including interactions between action plans of multiple players. In this framework, the appraisal of actual or potential threats is a necessary capability for impact assessment. This paper reviews and discusses in details the fundamental concepts of threat analysis. In particular, threat analysis generally attempts to compute some threat value, for the individual tracks, that estimates the degree of severity with which engagement events will potentially occur. Presenting relevant tracks to the decision maker in some threat list, sorted from the most threatening to the least, is clearly in-line with the cognitive demands associated with threat evaluation. A key parameter in many threat value evaluation techniques is the Closest Point of Approach (CPA). Along this line of thought, threatening tracks are often prioritized based upon which ones will reach their CPA first. Hence, the Time-to-CPA (TCPA), i.e., the time it will take for a track to reach its CPA, is also a key factor. Unfortunately, a typical assumption for the computation of the CPA/TCPA parameters is that the track velocity will remain constant. When a track is maneuvering, the CPA/TCPA values will change accordingly. These changes will in turn impact the threat value computations and, ultimately, the resulting threat list. This is clearly undesirable from a command decision-making perspective. In this regard, the paper briefly discusses threat value stabilization approaches based on neural networks and other mathematical techniques.

Choice of range-energy relationship for the analysis of electron-beam-induced-current line scans

NASA Astrophysics Data System (ADS)

Luke, Keung, L.

1994-07-01

The electron range in a material is an important parameter in the analysis of electron-beam-induced-current (EBIC) line scans. Both the Kanaya-Okayama (KO) and Everhart-Hoff (EH) range-energy relationships have been widely used by investigators for this purpose. Although the KO range is significantly larer than the EH range, no study has been done to examine the effect of choosing one range over the other on the values of the surface recombination velocity S(sub T) and minority-carrier diffusion length L evaluated from EBICF line scans. Such a study has been carried out, focusing on two major questions: (1) When the KO range is used in different reported methods to evaluate either or both S(sub T) and L from EBIC line scans, how different are their values thus determined in comparison to those using the EH range?; (2) from EBIC line scans of a given material, is there a way to discriminate between the KO and the EH ranges which should be used to analyze these scans? Answers to these questions are presented to assist investigators in extracting more reliable values of either or both S(sub T) and L and in finding the right range to use in the analysis of these line scans.

Application of a modified selection index for honey bees (Hymenoptera: Apidae).

PubMed

van Engelsdorp, D; Otis, G W

2000-12-01

Nine different genetic families of honey bees (Apis mellifera L.) were compared using summed z-scores (phenotypic values) and a modified selection index (Imod). Imod values incorporated both the phenotypic scores of the different traits and the economic weightings of these traits, as determined by a survey of commercial Ontario beekeepers. Largely because of the high weight all beekeepers place on honey production, a distinct difference between line rankings based on phenotypic scores and Imod scores was apparent, thereby emphasizing the need to properly weight the traits being evaluated to select bee stocks most valuable for beekeepers. Furthermore, when beekeepers who made >10% of their income from queen and nucleus colony sales assigned relative values to the traits used in the Imod calculations, the results differed from those based on weightings assigned by honey producers. Our results underscore the difficulties the North American beekeeping industry must overcome to devise effective methods of evaluating colonies for breeding purposes.

Effects of balanced selection for intramuscular fat and abdominal fat percentage and estimates of genetic parameters.

PubMed

Jiang, M; Fan, W L; Xing, S Y; Wang, J; Li, P; Liu, R R; Li, Q H; Zheng, M Q; Cui, H X; Wen, J; Zhao, G P

2017-02-01

Intramuscular fat (IMF) content contributes to meat flavor and improves meat quality. Excessive abdominal fat, however, leads to a waste of feed resources. Here, an independent up-selection for IMF was used as a control (Line C), and a balanced selection program, with up-selection for IMF and down-selection AFP (Line B), was studied in JingXing yellow chickens. The mean of IMF and AFP within a family was the phenotypic value upon which selection was based. The selective pressures of IMF in line B and line C were the same in each generation. At G5, the IMF was significantly higher (P < 0.05) than that at G0 in both lines. For AFP, Line C was significantly higher at G5 (P < 0.05) than at G0, but the difference in Line B was not significant (P > 0.05). IMF increased by 11.4% and AFP decreased by 1.5% in Line B compared with the G0 generation. In contrast, the IMF increased by 17.6%, but was accompanied by an 18.7% increase in AFP, in control Line C. Of 10 other traits measured, body weight at 56 d age (BW56) and the percentages of eviscerated weight (EWP) showed a significant difference between the 2 lines (P < 0.05). The heritabilities for IMF and AFP, estimated by the DMU package, were 0.16 and 0.32, respectively. A moderate positive correlation existed between IMF and AFP (0.35). A balanced selection program for increasing IMF while controlling AFP (Line B) is shown here to be effective in practical chicken breeding. © 2016 Poultry Science Association Inc.

Cyclotron Line Measurements with INTEGRAL

NASA Technical Reports Server (NTRS)

Pottschmidt, K.; Kreykenbohm, I.; Caballero, I.; Fritz, S.; Schoenherr, G.; Kretschmar, P.; Wilms, J.; McBride, V. A.; Suchy, S.; Rothschild, R. E.

2008-01-01

Due to its broadband energy coverage, INTEGRAL has made important contributions to observing and interpreting cyclotron lines, which are present in the 10-100 keV range of a sample of accreting pulsars. In these systems photons with energies fulfilling the resonance condition inelastically Compton scatter off electrons quantized in the accretion column above the neutron star's magnetic pole(s). This process gives rise to the broad, absorption-like lines or 'cyclotron resonant scattering features' (CRSF). The observed lines allow to directly measure the B-fields of these sources, resulting in values of a few times 1E12G. In this overview I will present recent highlights regarding CRSF observations as well as discuss current ideas and models for the physical conditions in the accretion column. Among the former are the stability of the spectrum of Vela X-1 during giant flares in 2003, the observation of three cyclotron lines during the 2004 outburst of V0332+53, the confirmation of the fundamental line at approximately 45 keV during a 2005 normal outburst of A0535-26, and the simultaneous detection of the two lines in the dipping source 4U 1907+09 (for which also a torque reversal was detected for the first time). Through these and other observations it has become increasingly apparent that two types of observations can potentially be used to constrain the accretion column geometry: the determination of energy ratios for multiple harmonic lines (only two sources with greater than 2 lines are known), was well as the evolution of the fundamental line centroid, which, for different sources, may or may not be correlated with flux. Furthermore, first steps have been taken away from the usual phenomenological description of the lines, towards a physical approach based on self-consistent CRSF modeling. Initial applications are presented.

Design optimization of RF lines in vacuum environment for the MITICA experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Muri, Michela, E-mail: michela.demuri@igi.cnr.it; Consorzio RFX, Corso Stati Uniti, 4, I-35127 Padova; Pavei, Mauro

This contribution regards the Radio Frequency (RF) transmission line of the Megavolt ITER Injector and Concept Advancement (MITICA) experiment. The original design considered copper coaxial lines of 1″ 5/8, but thermal simulations under operating conditions showed maximum temperatures of the lines at regime not compatible with the prescription of the component manufacturer. Hence, an optimization of the design was necessary. Enhancing thermal radiation and increasing the conductor size were considered for design optimization: thermal analyses were carried out to calculate the temperature of MITICA RF lines during operation, as a function of the emissivity value and of other geometrical parameters.more » Five coating products to increase the conductor surface emissivity were tested, measuring the outgassing behavior of the selected products and the obtained emissivity values.« less

Assessing effective population size, coancestry and inbreeding effects on litter size using the pedigree and SNP data in closed lines of the Iberian pig breed.

PubMed

Silió, L; Barragán, C; Fernández, A I; García-Casco, J; Rodríguez, M C

2016-04-01

The complete pedigree of two closed Iberian pig lines (Gamito and Torbiscal), with 798 and 4077 reproducers, has been used to measure the evolution of coancestry (f) and inbreeding (F) for autosomal and X-linked genes along 16 and 28 respective equivalent discrete generations. At the last generation, the mean values of each line were f = 0.41 and 0.22, F = 0.35 and 0.18, fX  = 0.46 and 0.22 and FX  = 0.47 and 0.19, respectively. Other calculated parameters were the effective number of founders (final values, 6.8 and 35.2) and non-founders (1.5 and 2.4), founder genome equivalents (1.2 and 2.3) and effective population size (16.0 and 57.7). Measures of Torbiscal effective size based on rates of coancestry (66.1), inbreeding (65.0) and linkage disequilibrium (71.0) were estimated from whole-genome SNP genotyping data. Values of new and old inbreeding and their respective rates by generation were computed to detect purging effects of natural selection. The analysis of 6854 Torbiscal litters showed significant negative impacts of new and fast inbreeding on litter size, as expected from the purging hypothesis: -0.20 born piglets per litter by a 10% of new inbreeding, and -0.03 and -0.02 piglets by 1% of total and new inbreeding rates, respectively. The analysis performed on 1274 litters of the Gamito line failed to show purging effects. The only significant results were reductions in -0.91 and -0.17 piglets by a 10% of old and X-linked genes inbreeding, respectively. These results may be useful for some practical issues in conservation programs of farm or captive wild animals. © 2015 Blackwell Verlag GmbH.

Cytotoxic, Antiproliferative and Apoptotic Effects of Perillyl Alcohol and Its Biotransformation Metabolite on A549 and HepG2 Cancer Cell Lines.

PubMed

Oturanel, Ceren E; Kıran, İsmail; Özşen, Özge; Çiftçi, Gülşen A; Atlı, Özlem

2017-01-01

A monoterpene, perillyl alcohol, has attracted attention in medicinal chemistry since it exhibited chemo-preventive and therapeutic properties against a variety of cancers. In the present work, it was aimed to obtain derivatives of perillyl alcohol through microbial biotransformation and investigate their anticancer activities against A549 and HepG2 cancer cell lines. Biotransformation studies were carried out in a α-medium for 7 days at 25oC. XTT assay was performed to investigate the anticancer activities of perillyl alcohol and its biotransformation metabolite, dehydroperillic acid, against A549 and HepG2 cell lines and their selectivity using healthy cell line, NIH/3T3. Cell proliferation ELISA, BRDU (colorimetric) assay was used for measurement of proliferation in replicative cells in which DNA synthesis occurs. Flow cytometric analyses were also carried out for measuring apoptotic cell percentages, caspase 3 activation and mitochondrial membrane potential. Biotransformation of perillyl alcohol with Fusarium culmorum yielded dehydroperillic acid in a yield of 20.4 %. In in vitro anticancer studies, perillyl alcohol was found to exert cytotoxicity against HepG2 cell line with an IC50 value of 409.2 μg/mL. However, this effect was not found to be selective because of its higher IC50 (250 μg/mL) value against NIH/3T3 cell line. On the other hand, dehydroperillic acid was found to be effective and also selective against A549 cell line with an IC50 value of 125 μg/mL and a selectivity index (SI) value of 400. Apoptosis inducing effects of dehydroperillic acid was better in A549 cell line. Dehydroperillic acid may be a good candidate for therapy of lung adenocarcinoma and may show this anticancer activity by inducing apoptosis. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

The relationship between grain hardness, dough mixing parameters and bread-making quality in winter wheat.

PubMed

Salmanowicz, Bolesław P; Adamski, Tadeusz; Surma, Maria; Kaczmarek, Zygmunt; Karolina, Krystkowiak; Kuczyńska, Anetta; Banaszak, Zofia; Lugowska, Bogusława; Majcher, Małgorzata; Obuchowski, Wiktor

2012-01-01

The influence of grain hardness, determined by using molecular markers and physical methods (near-infrared (NIR) technique and particle size index-PSI) on dough characteristics, which in turn were determined with the use of a farinograph and reomixer, as well as bread-making properties were studied. The material covered 24 winter wheat genotypes differing in grain hardness. The field experiment was conducted at standard and increased levels of nitrogen fertilization. Results of molecular analyses were in agreement with those obtained by the use of physical methods for soft-grained lines. Some lines classified as hard (by physical methods) appeared to have the wild-type Pina and Pinb alleles, similar to soft lines. Differences in dough and bread-making properties between lines classified as hard and soft on the basis of molecular data appeared to be of less significance than the differences between lines classified as hard and soft on the basis of physical analyses of grain texture. Values of relative grain hardness at the increased nitrogen fertilization level were significantly higher. At both fertilization levels the NIR parameter determining grain hardness was significantly positively correlated with the wet gluten and sedimentation values, with most of the rheological parameters and bread yield. Values of this parameter correlated with quality characteristics in a higher degree than values of particle size index.

The Relationship Between Grain Hardness, Dough Mixing Parameters and Bread-Making Quality in Winter Wheat

PubMed Central

Salmanowicz, Bolesław P.; Adamski, Tadeusz; Surma, Maria; Kaczmarek, Zygmunt; Karolina, Krystkowiak; Kuczyńska, Anetta; Banaszak, Zofia; Ługowska, Bogusława; Majcher, Małgorzata; Obuchowski, Wiktor

2012-01-01

The influence of grain hardness, determined by using molecular markers and physical methods (near-infrared (NIR) technique and particle size index—PSI) on dough characteristics, which in turn were determined with the use of a farinograph and reomixer, as well as bread-making properties were studied. The material covered 24 winter wheat genotypes differing in grain hardness. The field experiment was conducted at standard and increased levels of nitrogen fertilization. Results of molecular analyses were in agreement with those obtained by the use of physical methods for soft-grained lines. Some lines classified as hard (by physical methods) appeared to have the wild-type Pina and Pinb alleles, similar to soft lines. Differences in dough and bread-making properties between lines classified as hard and soft on the basis of molecular data appeared to be of less significance than the differences between lines classified as hard and soft on the basis of physical analyses of grain texture. Values of relative grain hardness at the increased nitrogen fertilization level were significantly higher. At both fertilization levels the NIR parameter determining grain hardness was significantly positively correlated with the wet gluten and sedimentation values, with most of the rheological parameters and bread yield. Values of this parameter correlated with quality characteristics in a higher degree than values of particle size index. PMID:22605973

Cost-minimization analysis of panitumumab compared with cetuximab for first-line treatment of patients with wild-type RAS metastatic colorectal cancer.

PubMed

Graham, Christopher N; Hechmati, Guy; Fakih, Marwan G; Knox, Hediyyih N; Maglinte, Gregory A; Hjelmgren, Jonas; Barber, Beth; Schwartzberg, Lee S

2015-01-01

To compare the costs of first-line treatment with panitumumab + FOLFOX in comparison to cetuximab + FOLFIRI among patients with wild-type (WT) RAS metastatic colorectal cancer (mCRC) in the US. A cost-minimization model was developed assuming similar treatment efficacy between both regimens. The model estimated the costs associated with drug acquisition, treatment administration frequency (every 2 weeks for panitumumab, weekly for cetuximab), and incidence of infusion reactions. Average anti-EGFR doses were calculated from the ASPECCT clinical trial, and average doses of chemotherapy regimens were based on product labels. Using the medical component of the consumer price index, adverse event costs were inflated to 2014 US dollars, and all other costs were reported in 2014 US dollars. The time horizon for the model was based on average first-line progression-free survival of a WT RAS patient, estimated from parametric survival analyses of PRIME clinical trial data. Relative to cetuximab + FOLFIRI in the first-line treatment of WT RAS mCRC, the cost-minimization model demonstrated lower projected drug acquisition, administration, and adverse event costs for patients who received panitumumab + FOLFOX. The overall cost per patient for first-line treatment was $179,219 for panitumumab + FOLFOX vs $202,344 for cetuximab + FOLFIRI, resulting in a per-patient saving of $23,125 (11.4%) in favor of panitumumab + FOLFOX. From a value perspective, the cost-minimization model supports panitumumab + FOLFOX instead of cetuximab + FOLFIRI as the preferred first-line treatment of WT RAS mCRC patients requiring systemic therapy.

The ionization mechanism of NGC 185: how to fake a Seyfert galaxy?

NASA Astrophysics Data System (ADS)

Martins, L. P.; Lanfranchi, G.; Gonçalves, D. R.; Magrini, L.; Teodorescu, A. M.; Quireza, C.

2012-02-01

NGC 185 is a dwarf spheroidal satellite of the Andromeda galaxy. From mid-1990s onwards it was revealed that dwarf spheroidals often display a varied and in some cases complex star formation history. In an optical survey of bright nearby galaxies, NGC 185 was classified as a Seyfert galaxy based on its emission line ratios. However, although the emission lines in this object formally place it in the category of Seyferts, it is probable that this galaxy does not contain a genuine active nucleus. NGC 185 was not detected in radio surveys either in 6 or 20 cm, or X-ray observations, which means that the Seyfert-like line ratios may be produced by stellar processes. In this work, we try to identify the possible ionization mechanisms for this galaxy. We discussed the possibility of the line emissions being produced by planetary nebulae (PNe), using deep spectroscopy observations obtained with the Gemini Multi-Object Spectrograph - North (GMOS-N), at Gemini. Although the fluxes of the PNe are high enough to explain the integrated spectrum, the line ratios are very far from the values for the Seyfert classification. We then proposed that a mixture of supernova remnants and PNe could be the source of the ionization, and we show that a composition of these two objects do mimic Seyfert-like line ratios. We used chemical evolution models to predict the supernova rates and to support the idea that these supernova remnants should be present in the galaxy. Based on observations obtained at the Gemini Observatory, which is operated by the Association of Universities for Research in Astronomy, Inc., under a cooperative agreement with the NSF on behalf of the Gemini partnership.

Biases in Metallicity Measurements from Global Galaxy Spectra: The Effects of Flux Weighting and Diffuse Ionized Gas Contamination

NASA Astrophysics Data System (ADS)

Sanders, Ryan L.; Shapley, Alice E.; Zhang, Kai; Yan, Renbin

2017-12-01

Galaxy metallicity scaling relations provide a powerful tool for understanding galaxy evolution, but obtaining unbiased global galaxy gas-phase oxygen abundances requires proper treatment of the various line-emitting sources within spectroscopic apertures. We present a model framework that treats galaxies as ensembles of H II and diffuse ionized gas (DIG) regions of varying metallicities. These models are based upon empirical relations between line ratios and electron temperature for H II regions, and DIG strong-line ratio relations from SDSS-IV MaNGA IFU data. Flux-weighting effects and DIG contamination can significantly affect properties inferred from global galaxy spectra, biasing metallicity estimates by more than 0.3 dex in some cases. We use observationally motivated inputs to construct a model matched to typical local star-forming galaxies, and quantify the biases in strong-line ratios, electron temperatures, and direct-method metallicities as inferred from global galaxy spectra relative to the median values of the H II region distributions in each galaxy. We also provide a generalized set of models that can be applied to individual galaxies or galaxy samples in atypical regions of parameter space. We use these models to correct for the effects of flux-weighting and DIG contamination in the local direct-method mass-metallicity and fundamental metallicity relations, and in the mass-metallicity relation based on strong-line metallicities. Future photoionization models of galaxy line emission need to include DIG emission and represent galaxies as ensembles of emitting regions with varying metallicity, instead of as single H II regions with effective properties, in order to obtain unbiased estimates of key underlying physical properties.

Cost-Effectiveness Analysis of Regorafenib for Metastatic Colorectal Cancer

PubMed Central

Goldstein, Daniel A.; Ahmad, Bilal B.; Chen, Qiushi; Ayer, Turgay; Howard, David H.; Lipscomb, Joseph; El-Rayes, Bassel F.; Flowers, Christopher R.

2015-01-01

Purpose Regorafenib is a standard-care option for treatment-refractory metastatic colorectal cancer that increases median overall survival by 6 weeks compared with placebo. Given this small incremental clinical benefit, we evaluated the cost-effectiveness of regorafenib in the third-line setting for patients with metastatic colorectal cancer from the US payer perspective. Methods We developed a Markov model to compare the cost and effectiveness of regorafenib with those of placebo in the third-line treatment of metastatic colorectal cancer. Health outcomes were measured in life-years and quality-adjusted life-years (QALYs). Drug costs were based on Medicare reimbursement rates in 2014. Model robustness was addressed in univariable and probabilistic sensitivity analyses. Results Regorafenib provided an additional 0.04 QALYs (0.13 life-years) at a cost of $40,000, resulting in an incremental cost-effectiveness ratio of $900,000 per QALY. The incremental cost-effectiveness ratio for regorafenib was > $550,000 per QALY in all of our univariable and probabilistic sensitivity analyses. Conclusion Regorafenib provides minimal incremental benefit at high incremental cost per QALY in the third-line management of metastatic colorectal cancer. The cost-effectiveness of regorafenib could be improved by the use of value-based pricing. PMID:26304904

Toward a Quantitative Comparison of Magnetic Field Extrapolations and Observed Coronal Loops

NASA Astrophysics Data System (ADS)

Warren, Harry P.; Crump, Nicholas A.; Ugarte-Urra, Ignacio; Sun, Xudong; Aschwanden, Markus J.; Wiegelmann, Thomas

2018-06-01

It is widely believed that loops observed in the solar atmosphere trace out magnetic field lines. However, the degree to which magnetic field extrapolations yield field lines that actually do follow loops has yet to be studied systematically. In this paper, we apply three different extrapolation techniques—a simple potential model, a nonlinear force-free (NLFF) model based on photospheric vector data, and an NLFF model based on forward fitting magnetic sources with vertical currents—to 15 active regions that span a wide range of magnetic conditions. We use a distance metric to assess how well each of these models is able to match field lines to the 12202 loops traced in coronal images. These distances are typically 1″–2″. We also compute the misalignment angle between each traced loop and the local magnetic field vector, and find values of 5°–12°. We find that the NLFF models generally outperform the potential extrapolation on these metrics, although the differences between the different extrapolations are relatively small. The methodology that we employ for this study suggests a number of ways that both the extrapolations and loop identification can be improved.

Quantification of sensitivity and resistance of breast cancer cell lines to anti-cancer drugs using GR metrics

PubMed Central

Hafner, Marc; Heiser, Laura M.; Williams, Elizabeth H.; Niepel, Mario; Wang, Nicholas J.; Korkola, James E.; Gray, Joe W.; Sorger, Peter K.

2017-01-01

Traditional means for scoring the effects of anti-cancer drugs on the growth and survival of cell lines is based on relative cell number in drug-treated and control samples and is seriously confounded by unequal division rates arising from natural biological variation and differences in culture conditions. This problem can be overcome by computing drug sensitivity on a per-division basis. The normalized growth rate inhibition (GR) approach yields per-division metrics for drug potency (GR50) and efficacy (GRmax) that are analogous to the more familiar IC50 and Emax values. In this work, we report GR-based, proliferation-corrected, drug sensitivity metrics for ~4,700 pairs of breast cancer cell lines and perturbagens. Such data are broadly useful in understanding the molecular basis of therapeutic response and resistance. Here, we use them to investigate the relationship between different measures of drug sensitivity and conclude that drug potency and efficacy exhibit high variation that is only weakly correlated. To facilitate further use of these data, computed GR curves and metrics can be browsed interactively at http://www.GRbrowser.org/. PMID:29112189

A new critical dimension metrology for chrome-on-glass substrates based on s-parameter measurements extracted from coplanar waveguide test structures

NASA Astrophysics Data System (ADS)

Nwokoye, Chidubem A.; Zaghloul, Mona; Cresswell, Michael W.; Allen, Richard A.; Murabito, Christine E.

2006-10-01

The technical objective of the work reported here is to assess whether radio-frequency (RF) measurements made on coplanar waveguide (CPW) test structures, which are replicated in conducting material on insulating substrates, could be employed to extract the critical dimension (CD) of the signal line using its center-to-center separation from the groundlines as a reference. The specific near-term objective is to assess whether this CPW-based CD-metrology has sensitivity and repeatability competitive with the other metrology techniques that are now used for chrome-on-glass (COG) photomasks. An affirmative answer is encouraging because advancing to a non-contact and non-vacuum implementation would then seem possible for this application. Our modeling of specific cases shows that, when the pitch of the replicated lines of the CPW is maintained constant, the sensitivity of its characteristic impedance to the CDs of the signal and ground lines is approximately 60 Ω/μm. This is a potentially useful result. For the same implementation, the quantity ∂C/∂w has a value of approximately 45 (pF/m)/μm, which appears to be large enough to provide acceptable accuracy.

The FERRUM Project: Experimental Transition Probabilities of [Fe II] and Astrophysical Applications

NASA Technical Reports Server (NTRS)

Hartman, H.; Derkatch, A.; Donnelly, M. P.; Gull, T.; Hibbert, A.; Johannsson, S.; Lundberg, H.; Mannervik, S.; Norlin, L. -O.; Rostohar, D.

2002-01-01

We report on experimental transition probabilities for thirteen forbidden [Fe II] lines originating from three different metastable Fe II levels. Radiative lifetimes have been measured of two metastable states by applying a laser probing technique on a stored ion beam. Branching ratios for the radiative decay channels, i.e. M1 and E2 transitions, are derived from observed intensity ratios of forbidden lines in astrophysical spectra and compared with theoretical data. The lifetimes and branching ratios are combined to derive absolute transition probabilities, A-values. We present the first experimental lifetime values for the two Fe II levels a(sup 4)G(sub 9/2) and b(sup 2)H(sub 11/2) and A-values for 13 forbidden transitions from a(sup 6)S(sub 5/2), a(sup 4)G(sub 9/2) and b(sup 4)D(sub 7/2) in the optical region. A discrepancy between the measured and calculated values of the lifetime for the b(sup 2)H(sub 11/2) level is discussed in terms of level mixing. We have used the code CIV3 to calculate transition probabilities of the a(sup 6)D-a(sup 6)S transitions. We have also studied observational branching ratios for lines from 5 other metastable Fe II levels and compared them to calculated values. A consistency in the deviation between calibrated observational intensity ratios and theoretical branching ratios for lines in a wider wavelength region supports the use of [Fe II] lines for determination of reddening.

A Fractal Interpretation of Controlled-Source Helicopter Electromagnetic Survey Data: Seco Creek, Edwards Aquifer, TX

NASA Astrophysics Data System (ADS)

Decker, K. T.; Everett, M. E.

2009-12-01

The Edwards aquifer lies in the structurally complex Balcones fault zone and supplies water to the growing city of San Antonio. To ensure that future demands for water are met, the hydrological and geophysical properties of the aquifer must be well-understood. In most settings, fracture lengths and displacements occur in power-law distributions. Fracture distribution plays an important role in determining electrical and hydraulic current flowpaths. 1-D synthetic models of the controlled-source electromagnetic (CSEM) response for layered models with a fractured layer at depth described by the roughness parameter βV, such that 0≤βV<1, associated with the power-law length-scale dependence of electrical conductivity are developed. A value of βV = 0 represents homogeneous, continuous media, while a value of 0<βV<1 shows that roughness exists. The Seco Creek frequency-domain helicopter electromagnetic survey data set is analyzed by introducing the similarly defined roughness parameter βH to detect lateral roughness along survey lines. Fourier transforming the apparent resistivity as a function of position along flight line into wavenumber domain using a 256-point sliding window gives the power spectral density (PSD) plot for each line. The value of βH is the slope of the least squares regression for the PSD in each 256-point window. Changes in βH with distance along the flight line are plotted. Large values of βH are found near well-known large fractures and maps of βH produced by interpolating values of βH along survey lines suggest previously undetected structure at depth.

Analysis of the therapeutic gain in the treatment of human osteosarcoma microcolonies in vitro with 211At-labelled monoclonal antibody.

PubMed

Larsen, R H; Bruland, O S; Hoff, P; Alstad, J; Rofstad, E K

1994-06-01

Microcolonies were obtained by culturing cells of two human osteosarcoma lines (OHS and KPDX) and one human melanoma line (WIX-c) for either 24 or 72 h. The microcolonies were treated with either alpha-particle radiation emitted by the 211At-labelled monoclonal antibody (MAb) TP-3 or external beam X-rays. Survival of microcolonies was assayed by colony formation. Therapeutic gain factor (TGF) values were calculated for two survival levels, 50% and 20% microcolony regeneration (i.e. at least one cell in 50% or 20% of the colonies survived the treatments). The TGF values were affected by the specific activity of the 211At-MAb conjugate, the antigen expression of the cells and the size and growth pattern of the microcolonies. Treatment with 211At-TP-3 gave TGF values that varied from 1.3 +/- 0.4 to 4.5 +/- 0.7 (mean +/- s.e.). The antigen-rich OHS cell line had on average 1.6 times higher TGF than the antigen-poor KPDX cell line. The TGF increased significantly with colony size for the densely packed colonies of the KPDX cell line but not for the OHS cell line, which had colonies with cells growing in a more scattered pattern. Control experiments with the two non-specific 211At forms, free 211At and 211At-labelled bovine serum albumin, gave TGF values from 0.6 +/- 0.1 to 1.0 +/- 0.3. This study suggests that in vivo evaluation of 211At-MAbs using relevant tumour models is desirable.

Analysis of the therapeutic gain in the treatment of human osteosarcoma microcolonies in vitro with 211At-labelled monoclonal antibody.

PubMed Central

Larsen, R. H.; Bruland, O. S.; Hoff, P.; Alstad, J.; Rofstad, E. K.

1994-01-01

Microcolonies were obtained by culturing cells of two human osteosarcoma lines (OHS and KPDX) and one human melanoma line (WIX-c) for either 24 or 72 h. The microcolonies were treated with either alpha-particle radiation emitted by the 211At-labelled monoclonal antibody (MAb) TP-3 or external beam X-rays. Survival of microcolonies was assayed by colony formation. Therapeutic gain factor (TGF) values were calculated for two survival levels, 50% and 20% microcolony regeneration (i.e. at least one cell in 50% or 20% of the colonies survived the treatments). The TGF values were affected by the specific activity of the 211At-MAb conjugate, the antigen expression of the cells and the size and growth pattern of the microcolonies. Treatment with 211At-TP-3 gave TGF values that varied from 1.3 +/- 0.4 to 4.5 +/- 0.7 (mean +/- s.e.). The antigen-rich OHS cell line had on average 1.6 times higher TGF than the antigen-poor KPDX cell line. The TGF increased significantly with colony size for the densely packed colonies of the KPDX cell line but not for the OHS cell line, which had colonies with cells growing in a more scattered pattern. Control experiments with the two non-specific 211At forms, free 211At and 211At-labelled bovine serum albumin, gave TGF values from 0.6 +/- 0.1 to 1.0 +/- 0.3. This study suggests that in vivo evaluation of 211At-MAbs using relevant tumour models is desirable. PMID:8198960

Assessment of Labor Behavior Factors and Selecting Line Managers' Lines of Development at Russian Industrial Enterprises

ERIC Educational Resources Information Center

Zavyalova, Elena K.; Kosheleva, Sofia V.

2009-01-01

Purpose: The paper investigates personal and environmental factors providing for the efficiency of line managers' activity and contributing to their professional and career advancement. The paper studies the prognostic value of the assessment of personal and environmental factors providing for the efficiency of line managers' activity according to…

Thermal depinning of a single superconducting vortex

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sok, Junghyun

1995-06-19

Thermal depinning has been studied for a single vortex trapped in a superconducting thin film in order to determine the value of the superconducting order parameter and the superfluid density when the vortex depins and starts to move around the film. For the Pb film in Pb/Al/Al 2O 3/PbBi junction having a gold line, the vortex depins from the artificial pinning site (Au line) and reproducibly moves through the same sequence of other pinning sites before it leaves the junction area of the Pb film. Values of the normalized order parameter Δ/Δ ° vary from Δ/Δ °=0.20 at the firstmore » motion of the vortex to Δ/Δ °=0.16 where the vortex finally leaves the junction. Equivalently, the value of the normalized superfluid density changes from 4% to 2.5% for this sample in this same temperature interval. For the Nb film in Nb/Al/Al 2O 3/Nb junction, thermal depinning occurs when the value of Δ/Δ ° is approximately 0.22 and the value of ρ s/ρ so is approximately 5%. These values are about 20% larger than those of a Pb sample having a gold line, but the values are really very close. For the Nb sample, grain boundaries are important pinning sites whereas, for the Pb sample with a gold line, pinning may have been dominated by an array Pb 3AU precipitates. Because roughly the same answer was obtained for these rather different kinds of pinning site, there is a reasonable chance that this is a general value within factors of 2 for a wide range of materials.« less

Adaptive Spatial Filter Based on Similarity Indices to Preserve the Neural Information on EEG Signals during On-Line Processing

PubMed Central

Villa-Parra, Ana Cecilia; Bastos-Filho, Teodiano; López-Delis, Alberto; Frizera-Neto, Anselmo; Krishnan, Sridhar

2017-01-01

This work presents a new on-line adaptive filter, which is based on a similarity analysis between standard electrode locations, in order to reduce artifacts and common interferences throughout electroencephalography (EEG) signals, but preserving the useful information. Standard deviation and Concordance Correlation Coefficient (CCC) between target electrodes and its correspondent neighbor electrodes are analyzed on sliding windows to select those neighbors that are highly correlated. Afterwards, a model based on CCC is applied to provide higher values of weight to those correlated electrodes with lower similarity to the target electrode. The approach was applied to brain computer-interfaces (BCIs) based on Canonical Correlation Analysis (CCA) to recognize 40 targets of steady-state visual evoked potential (SSVEP), providing an accuracy (ACC) of 86.44 ± 2.81%. In addition, also using this approach, features of low frequency were selected in the pre-processing stage of another BCI to recognize gait planning. In this case, the recognition was significantly (p<0.01) improved for most of the subjects (ACC≥74.79%), when compared with other BCIs based on Common Spatial Pattern, Filter Bank-Common Spatial Pattern, and Riemannian Geometry. PMID:29186848

Collinear Points Problem

ERIC Educational Resources Information Center

Shultz, Harris S.; Shiflett, Ray C.

2008-01-01

Students were asked to find all possible values for A so that the points (1, 2), (5, A), and (A, 7) lie on a straight line. This problem suggests a generalization: Given (x, y), find all values of A so that the points (x, y), (5, A), and (A, 7) lie on a straight line. We find that this question about linear equations must be resolved using the…

Discrete Radon transform has an exact, fast inverse and generalizes to operations other than sums along lines

PubMed Central

Press, William H.

2006-01-01

Götz, Druckmüller, and, independently, Brady have defined a discrete Radon transform (DRT) that sums an image's pixel values along a set of aptly chosen discrete lines, complete in slope and intercept. The transform is fast, O(N2log N) for an N × N image; it uses only addition, not multiplication or interpolation, and it admits a fast, exact algorithm for the adjoint operation, namely backprojection. This paper shows that the transform additionally has a fast, exact (although iterative) inverse. The inverse reproduces to machine accuracy the pixel-by-pixel values of the original image from its DRT, without artifacts or a finite point-spread function. Fourier or fast Fourier transform methods are not used. The inverse can also be calculated from sampled sinograms and is well conditioned in the presence of noise. Also introduced are generalizations of the DRT that combine pixel values along lines by operations other than addition. For example, there is a fast transform that calculates median values along all discrete lines and is able to detect linear features at low signal-to-noise ratios in the presence of pointlike clutter features of arbitrarily large amplitude. PMID:17159155

Discrete Radon transform has an exact, fast inverse and generalizes to operations other than sums along lines.

PubMed

Press, William H

2006-12-19

Götz, Druckmüller, and, independently, Brady have defined a discrete Radon transform (DRT) that sums an image's pixel values along a set of aptly chosen discrete lines, complete in slope and intercept. The transform is fast, O(N2log N) for an N x N image; it uses only addition, not multiplication or interpolation, and it admits a fast, exact algorithm for the adjoint operation, namely backprojection. This paper shows that the transform additionally has a fast, exact (although iterative) inverse. The inverse reproduces to machine accuracy the pixel-by-pixel values of the original image from its DRT, without artifacts or a finite point-spread function. Fourier or fast Fourier transform methods are not used. The inverse can also be calculated from sampled sinograms and is well conditioned in the presence of noise. Also introduced are generalizations of the DRT that combine pixel values along lines by operations other than addition. For example, there is a fast transform that calculates median values along all discrete lines and is able to detect linear features at low signal-to-noise ratios in the presence of pointlike clutter features of arbitrarily large amplitude.

Highly ionized atoms in cooling gas

NASA Technical Reports Server (NTRS)

Edgar, R. J.; Chevalier, R. A.

1986-01-01

The ionization of low density gas cooling from a high temperature was calculated. The evolution during the cooling is assumed to be isochoric, isobaric, or a combination of these cases. The calculations are used to predict the column densities and ultraviolet line luminosities of highly ionized atoms in cooling gas. In a model for cooling of a hot galactic corona, it is shown that the observed value of N(N V) can be produced in the cooling gas, while the predicted value of N(Si IV) falls short of the observed value by a factor of about 5. The same model predicts fluxes of ultraviolet emission lines that are a factor of 10 lower than the claimed detections of Feldman, Brune, and Henry. Predictions are made for ultraviolet lines in cooling flows in early-type galaxies and clusters of galaxies. It is shown that the column densities of interest vary over a fairly narrow range, while the emission line luminosities are simply proportional to the mass inflow rate.

Highly ionized atoms in cooling gas. [in model for cooling of hot Galactic corona

NASA Technical Reports Server (NTRS)

Edgar, Richard J.; Chevalier, Roger A.

1986-01-01

The ionization of low density gas cooling from a high temperature was calculated. The evolution during the cooling is assumed to be isochoric, isobaric, or a combination of these cases. The calculations are used to predict the column densities and ultraviolet line luminosities of highly ionized atoms in cooling gas. In a model for cooling of a hot galactic corona, it is shown that the observed value of N(N V) can be produced in the cooling gas, while the predicted value of N(Si IV) falls short of the observed value by a factor of about 5. The same model predicts fluxes of ultraviolet emission lines that are a factor of 10 lower than the claimed detections of Feldman, Bruna, and Henry. Predictions are made for ultraviolet lines in cooling flows in early-type galaxies and clusters of galaxies. It is shown that the column densities of interest vary over a fairly narrow range, while the emission line luminosities are simply proportional to the mass inflow rate.

A Hybrid On-line Verification Method of Relay Setting

NASA Astrophysics Data System (ADS)

Gao, Wangyuan; Chen, Qing; Si, Ji; Huang, Xin

2017-05-01

Along with the rapid development of the power industry, grid structure gets more sophisticated. The validity and rationality of protective relaying are vital to the security of power systems. To increase the security of power systems, it is essential to verify the setting values of relays online. Traditional verification methods mainly include the comparison of protection range and the comparison of calculated setting value. To realize on-line verification, the verifying speed is the key. The verifying result of comparing protection range is accurate, but the computation burden is heavy, and the verifying speed is slow. Comparing calculated setting value is much faster, but the verifying result is conservative and inaccurate. Taking the overcurrent protection as example, this paper analyses the advantages and disadvantages of the two traditional methods above, and proposes a hybrid method of on-line verification which synthesizes the advantages of the two traditional methods. This hybrid method can meet the requirements of accurate on-line verification.

Rapid Spectral Variability of the Symbiotic Star CH Cyg During One Night

NASA Astrophysics Data System (ADS)

Mikayilov, Kh. M.; Rustamov, B. N.; Alakbarov, I. A.; Rustamova, A. B.

2017-06-01

During one night (15.07.2015), within 6 hours 14 echelle spectrograms of this star were obtained. It was revealed that the profile of Ha and Hβ lines have two-component emission structure with a central absorption, parameters which vary from spectrum to spectrum during the night. The intensity of blue emission component (V) have been changed strongly during the night: the value of ratio of intensities of violet and red components (V/R) of line Hα decreased from 0:93 to 0:49 in the beginning and then increased to a value of 0.97. The synchronous variations of values of V/R for the Hα and Hβ lines have been revealed. The parameters of blue emission components of Hα and of line Hel λ5876 Å are correlated. We propose that revealed by us the rapid spectral changes in the spectrum of the star CH Cyg could be connected with a flickering in the optical brightness of the star that is typical for the active phase of this system.

A locus problem solved by using a mechanism with three dyads and two leading elements

NASA Astrophysics Data System (ADS)

Popescu, I.; Sass, L.; Romanescu, A. E.

2016-11-01

In Geometry there are many types of loci, solved by means of classic geometrical considerations and yielding lines and arcs of circles or conics. Yet more complicated locus can be solved by means of the Theory of Mechanisms. Our research starts from a locus and provides a solution based on the Theory of Mechanisms, finding the equivalent mechanism. The structural and cinematic analysis of the mechanism is made, determining the trajectory of a point representing the locus which presents interest. The mechanism has three dyads and two leading elements, for which the movements were correlated by means of a coefficient q. For various values of q different loci were obtained, similar for close values of q but different for significantly different values of q.

An AK-LDMeans algorithm based on image clustering

NASA Astrophysics Data System (ADS)

Chen, Huimin; Li, Xingwei; Zhang, Yongbin; Chen, Nan

2018-03-01

Clustering is an effective analytical technique for handling unmarked data for value mining. Its ultimate goal is to mark unclassified data quickly and correctly. We use the roadmap for the current image processing as the experimental background. In this paper, we propose an AK-LDMeans algorithm to automatically lock the K value by designing the Kcost fold line, and then use the long-distance high-density method to select the clustering centers to further replace the traditional initial clustering center selection method, which further improves the efficiency and accuracy of the traditional K-Means Algorithm. And the experimental results are compared with the current clustering algorithm and the results are obtained. The algorithm can provide effective reference value in the fields of image processing, machine vision and data mining.

Volcano plots in analyzing differential expressions with mRNA microarrays.

PubMed

Li, Wentian

2012-12-01

A volcano plot displays unstandardized signal (e.g. log-fold-change) against noise-adjusted/standardized signal (e.g. t-statistic or -log(10)(p-value) from the t-test). We review the basic and interactive use of the volcano plot and its crucial role in understanding the regularized t-statistic. The joint filtering gene selection criterion based on regularized statistics has a curved discriminant line in the volcano plot, as compared to the two perpendicular lines for the "double filtering" criterion. This review attempts to provide a unifying framework for discussions on alternative measures of differential expression, improved methods for estimating variance, and visual display of a microarray analysis result. We also discuss the possibility of applying volcano plots to other fields beyond microarray.

A fast invariant imbedding method for multiple scattering calculations and an application to equivalent widths of CO2 lines on Venus

NASA Technical Reports Server (NTRS)

Sato, M.; Kawabata, K.; Hansen, J. E.

1977-01-01

The invariant imbedding method considered is based on an equation which describes the change in the reflected radiation when an optically thin layer is added to the top of the atmosphere. The equation is used to treat the problem of reflection from a planetary atmosphere as an initial value problem. A fast method is discussed for the solution of the invariant imbedding equation. The speed and accuracy of the new method are illustrated by comparing it with the doubling program published by Hansen and Travis (1974). Computations are performed of the equivalent widths of carbon dioxide absorption lines in solar radiation reflected by Venus for several models of the planetary atmosphere.

Calibration and Limitations of the Mg II Line-based Black Hole Masses

NASA Astrophysics Data System (ADS)

Woo, Jong-Hak; Le, Huynh Anh N.; Karouzos, Marios; Park, Dawoo; Park, Daeseong; Malkan, Matthew A.; Treu, Tommaso; Bennert, Vardha N.

2018-06-01

We present single-epoch black hole mass ({M}BH}) calibrations based on the rest-frame ultraviolet (UV) and optical measurements of Mg II 2798 Å and Hβ 4861 Å lines and the active galactic nucleus (AGN) continuum, using a sample of 52 moderate-luminosity AGNs at z ∼ 0.4 and z ∼ 0.6 with high-quality Keck spectra. We combine this sample with a large number of luminous AGNs from the Sloan Digital Sky Survey to increase the dynamic range for a better comparison of UV and optical velocity and luminosity measurements. With respect to the reference {M}BH} based on the line dispersion of Hβ and continuum luminosity at 5100 Å, we calibrate the UV and optical mass estimators by determining the best-fit values of the coefficients in the mass equation. By investigating whether the UV estimators show a systematic trend with Eddington ratio, FWHM of Hβ, Fe II strength, or UV/optical slope, we find no significant bias except for the slope. By fitting the systematic difference of Mg II-based and Hβ-based masses with the L 3000/L 5100 ratio, we provide a correction term as a function of the spectral index as ΔC = 0.24 (1 + α λ ) + 0.17, which can be added to the Mg II-based mass estimators if the spectral slope can be well determined. The derived UV mass estimators typically show >∼0.2 dex intrinsic scatter with respect to the Hβ-based {M}BH}, suggesting that the UV-based mass has an additional uncertainty of ∼0.2 dex, even if high-quality rest-frame UV spectra are available.

Model to Design Drip Hose Lateral Line

NASA Astrophysics Data System (ADS)

Ludwig, Rafael; Cury Saad, João Carlos

2014-05-01

Introduction The design criterion for non-pressure compensating drip hose is normally to have 10% of flow variation (Δq) in the lateral line, corresponding to 20% of head pressure variation (ΔH). Longer lateral lines in drip irrigation systems using conventional drippers provide cost reduction, but it is necessary to obtain to the uniformity of irrigation [1]. The use of Δq higher levels can provide longer lateral lines. [4] proposes the use of a 30% Δq and he found that this value resulted in distribution uniformity over 80%. [1] considered it is possible to extend the lateral line length using two emitters spacing in different section. He assumed that the spacing changing point would be at 40% of the total length, because this is approximately the location of the average flow according with [2]. [3] found that, for practical purposes, the average pressure is located at 40% of the length of the lateral line and that until this point it has already consumed 75% of total pressure head loss (hf ). In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. Objective The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. Methodology A computer program was developed in Delphi® based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. Conclusions The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose. References [1] ANDRADE, L. A. D. Estudo de uniformidade de emissão de água utilizando diferentes espaçamentos entre gotejadores na linha lateral. 2009. 87 f. Tese (Doutorado em Agronomia/Irigação e Drenagem) - Faculdade de Ciências Agronômicas, Universidade Estadual Paulista 'Julio de Mesquita Filho', Botucatu, (2009). [2] KELLER, J.; BLIESNER, R. D. Sprinkle and trickle irrigation. Caldwell: Blackburn Press, (1990). 652 p. [3] TALENS, J. A. M. Riego localizado y fertirrigacion. Madrid: Mundi-Prensa, (2002). 533 p. [4] WU, I. P. An assessment of hydraulic design of micro-irrigation systems. Agricultural Water Management, Amsterdan, v. 32, n. 3

Force-Strain Characteristics and Rupture-Load Capability of Viking-Type Suspension-Line Material Under Dynamic Loading Conditions

NASA Technical Reports Server (NTRS)

Poole, Lamont R.; Councill, Earl L., Jr.

1972-01-01

A series of tests has been conducted to investigate the elastic behavior of Viking-type suspension-line material under dynamic loading conditions. Results indicate that there is a decrease in both rupture-load capability and elongation at rupture as the test strain rate is increased. Preliminary examination of force-strain characteristics indicates that, on the average, the material exhibits some type of viscous effect which results in a greater force being produced, for a particular value of strain, under dynamic loading conditions than that produced under quasi-static loading conditions. A great deal of uncertainty exists in defining a priori the tensile properties of viscoelastic materials, such as nylon or dacron, under dynamic loading conditions. Additional uncertainty enters the picture when woven configurations such as suspension,line material are considered. To eliminate these uncertainties, with respect to the Viking parachute configuration, a test program has been conducted to obtain data on the tensile properties of Viking-type suspension-line material over a wide range of strain rates. Based on preliminary examination of these data, the following conclusions can be drawn: 1. Material rupture-load capability decreases as strain-rate is increased. At strain rates above 75 percent/sec, no rupture loads were observed which would meet the minimum tensile strength specification of 880 pounds. 2. The material, on the average, exhibits some type of viscous effect which, for a particular value of strain, produces a greater load under dynamic loading conditions than that produced under quasi-static loading conditions.

Electronics and Algorithms for HOM Based Beam Diagnostics

NASA Astrophysics Data System (ADS)

Frisch, Josef; Baboi, Nicoleta; Eddy, Nathan; Nagaitsev, Sergei; Hensler, Olaf; McCormick, Douglas; May, Justin; Molloy, Stephen; Napoly, Olivier; Paparella, Rita; Petrosyan, Lyudvig; Ross, Marc; Simon, Claire; Smith, Tonee

2006-11-01

The signals from the Higher Order Mode (HOM) ports on superconducting cavities can be used as beam position monitors and to do survey structure alignment. A HOM-based diagnostic system has been installed to instrument both couplers on each of the 40 cryogenic accelerating structures in the DESY TTF2 Linac. The electronics uses a single stage down conversion from the 1.7 GHz HOM spectral line to a 20MHz IF which has been digitized. The electronics is based on low cost surface mount components suitable for large scale production. The analysis of the HOM data is based on Singular Value Decomposition. The response of the OM modes is calibrated using conventional BPMs.

Grey situation group decision-making method based on prospect theory.

PubMed

Zhang, Na; Fang, Zhigeng; Liu, Xiaqing

2014-01-01

This paper puts forward a grey situation group decision-making method on the basis of prospect theory, in view of the grey situation group decision-making problems that decisions are often made by multiple decision experts and those experts have risk preferences. The method takes the positive and negative ideal situation distance as reference points, defines positive and negative prospect value function, and introduces decision experts' risk preference into grey situation decision-making to make the final decision be more in line with decision experts' psychological behavior. Based on TOPSIS method, this paper determines the weight of each decision expert, sets up comprehensive prospect value matrix for decision experts' evaluation, and finally determines the optimal situation. At last, this paper verifies the effectiveness and feasibility of the method by means of a specific example.

Grey Situation Group Decision-Making Method Based on Prospect Theory

PubMed Central

Zhang, Na; Fang, Zhigeng; Liu, Xiaqing

2014-01-01

This paper puts forward a grey situation group decision-making method on the basis of prospect theory, in view of the grey situation group decision-making problems that decisions are often made by multiple decision experts and those experts have risk preferences. The method takes the positive and negative ideal situation distance as reference points, defines positive and negative prospect value function, and introduces decision experts' risk preference into grey situation decision-making to make the final decision be more in line with decision experts' psychological behavior. Based on TOPSIS method, this paper determines the weight of each decision expert, sets up comprehensive prospect value matrix for decision experts' evaluation, and finally determines the optimal situation. At last, this paper verifies the effectiveness and feasibility of the method by means of a specific example. PMID:25197706

The NSO FTS database program and archive (FTSDBM)

NASA Technical Reports Server (NTRS)

Lytle, D. M.

1992-01-01

Data from the NSO Fourier transform spectrometer is being re-archived from half inch tape onto write-once compact disk. In the process, information about each spectrum and a low resolution copy of each spectrum is being saved into an on-line database. FTSDBM is a simple database management program in the NSO external package for IRAF. A command language allows the FTSDBM user to add entries to the database, delete entries, select subsets from the database based on keyword values including ranges of values, create new database files based on these subsets, make keyword lists, examine low resolution spectra graphically, and make disk number/file number lists. Once the archive is complete, FTSDBM will allow the database to be efficiently searched for data of interest to the user and the compact disk format will allow random access to that data.

Off-line tracking of series parameters in distribution systems using AMI data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Tess L.; Sun, Yannan; Schneider, Kevin

2016-05-01

Electric distribution systems have historically lacked measurement points, and equipment is often operated to its failure point, resulting in customer outages. The widespread deployment of sensors at the distribution level is enabling observability. This paper presents an off-line parameter value tracking procedure that takes advantage of the increasing number of measurement devices being deployed at the distribution level to estimate changes in series impedance parameter values over time. The tracking of parameter values enables non-diurnal and non-seasonal change to be flagged for investigation. The presented method uses an unbalanced Distribution System State Estimation (DSSE) and a measurement residual-based parameter estimationmore » procedure. Measurement residuals from multiple measurement snapshots are combined in order to increase the effective local redundancy and improve the robustness of the calculations in the presence of measurement noise. Data from devices on the primary distribution system and from customer meters, via an AMI system, form the input data set. Results of simulations on the IEEE 13-Node Test Feeder are presented to illustrate the proposed approach applied to changes in series impedance parameters. A 5% change in series resistance elements can be detected in the presence of 2% measurement error when combining less than 1 day of measurement snapshots into a single estimate.« less

Green Net Value Added as a Sustainability Metric Based on ...

EPA Pesticide Factsheets

Sustainability measurement in economics involves evaluation of environmental and economic impact in an integrated manner. In this study, system level economic data are combined with environmental impact from a life cycle assessment (LCA) of a common product. We are exploring a costing approach that captures traditional costs but also incorporates externality costs to provide a convenient, easily interpretable metric. Green Net Value Added (GNVA) is a type of full cost accounting that incorporates total revenue, the cost of materials and services, depreciation, and environmental externalities. Two, but not all, of the potential environmental impacts calculated by the standard LCIA method (TRACI) could be converted to externality cost values. We compute externality costs disaggregated by upstream sectors, full cost, and GNVA to evaluate the relative sustainability of Bounty® paper towels manufactured at two production facilities. We found that the longer running, more established line had a higher GNVA than the newer line. The dominant factors contributing to externality costs are calculated to come from the stationary sources in the supply chain: electricity generation (27-35%), refineries (20-21%), pulp and paper making (15-23%). Health related externalities from Particulate Matter (PM2.5) and Carbon Dioxide equivalent (CO2e) emissions appear largely driven by electricity usage and emissions by the facilities, followed by pulp processing and transport. Supply

Critical state of sand matrix soils.

PubMed

Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

2014-01-01

The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803-0.998, 0.144-0.248, and 1.727-2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated.

Study on the near-field non-linearity (SMILE) of high power diode laser arrays

NASA Astrophysics Data System (ADS)

Zhang, Hongyou; Jia, Yangtao; Li, Changxuan; Zah, Chung-en; Liu, Xingsheng

2018-02-01

High power laser diodes have been found a wide range of industrial, space, medical applications, characterized by high conversion efficiency, small size, light weight and a long lifetime. However, due to thermal induced stress, each emitter in a semiconductor laser bar or array is displaced along p-n junction, resulting of each emitter is not in a line, called Near-field Non-linearity. Near-field Non-linearity along laser bar (also known as "SMILE") determines the outcome of optical coupling and beam shaping [1]. The SMILE of a laser array is the main obstacle to obtain good optical coupling efficiency and beam shaping from a laser array. Larger SMILE value causes a larger divergence angle and a wider line after collimation and focusing, respectively. In this letter, we simulate two different package structures based on MCC (Micro Channel Cooler) with Indium and AuSn solders, including the distribution of normal stress and the SMILE value. According to the theoretical results, we found the distribution of normal stress on laser bar shows the largest in the middle and drops rapidly near both ends. At last, we did another experiment to prove that the SMILE value of a laser bar was mainly affected by the die bonding process, rather than the operating condition.

Thermodynamic properties by Equation of state of liquid sodium under pressure

NASA Astrophysics Data System (ADS)

Li, Huaming; Sun, Yongli; Zhang, Xiaoxiao; Li, Mo

Isothermal bulk modulus, molar volume and speed of sound of molten sodium are calculated through an equation of state of a power law form within good precision as compared with the experimental data. The calculated internal energy data show the minimum along the isothermal lines as the previous result but with slightly larger values. The calculated values of isobaric heat capacity show the unexpected minimum in the isothermal compression. The temperature and pressure derivative of various thermodynamic quantities in liquid Sodium are derived. It is discussed about the contribution from entropy to the temperature and pressure derivative of isothermal bulk modulus. The expressions for acoustical parameter and nonlinearity parameter are obtained based on thermodynamic relations from the equation of state. Both parameters for liquid Sodium are calculated under high pressure along the isothermal lines by using the available thermodynamic data and numeric derivations. By comparison with the results from experimental measurements and quasi-thermodynamic theory, the calculated values are found to be very close at melting point at ambient condition. Furthermore, several other thermodynamic quantities are also presented. Scientific Research Starting Foundation from Taiyuan university of Technology, Shanxi Provincial government (``100-talents program''), China Scholarship Council and National Natural Science Foundation of China (NSFC) under Grant No. 11204200.

Critical State of Sand Matrix Soils

PubMed Central

Marto, Aminaton; Tan, Choy Soon; Makhtar, Ahmad Mahir; Kung Leong, Tiong

2014-01-01

The Critical State Soil Mechanic (CSSM) is a globally recognised framework while the critical states for sand and clay are both well established. Nevertheless, the development of the critical state of sand matrix soils is lacking. This paper discusses the development of critical state lines and corresponding critical state parameters for the investigated material, sand matrix soils using sand-kaolin mixtures. The output of this paper can be used as an interpretation framework for the research on liquefaction susceptibility of sand matrix soils in the future. The strain controlled triaxial test apparatus was used to provide the monotonic loading onto the reconstituted soil specimens. All tested soils were subjected to isotropic consolidation and sheared under undrained condition until critical state was ascertain. Based on the results of 32 test specimens, the critical state lines for eight different sand matrix soils were developed together with the corresponding values of critical state parameters, M, λ, and Γ. The range of the value of M, λ, and Γ is 0.803–0.998, 0.144–0.248, and 1.727–2.279, respectively. These values are comparable to the critical state parameters of river sand and kaolin clay. However, the relationship between fines percentages and these critical state parameters is too scattered to be correlated. PMID:24757417

Health state utility values in locally advanced and metastatic breast cancer by treatment line: a systematic review.

PubMed

Paracha, Noman; Thuresson, Per-Olof; Moreno, Santiago G; MacGilchrist, Katherine S

2016-10-01

For patients with late-stage (metastatic) breast cancer, the impact of treatment on health-related quality of life is a key factor in decision-making. A systematic review was conducted to identify health state utility values (HSUVs) for late-stage breast cancer, derived using methods preferred by health technology assessment (HTA) agencies, by treatment line. The aim was to generate a list of HSUVs, that could help to justify the values used to populate cost-utility models. Areas covered: Ten electronic databases, international congress websites and online HSUV databases were searched (January 1995-May 2014) for HSUVs for adults with late-stage breast cancer that had been derived from methods favoured by HTA agencies. Publications were included only if they reported studies that originated HSUVs. Expert commentary: Large numbers of HSUVs are available for late-stage breast cancer in the published literature. Contrary to expectations, the HSUVs reported in the literature vary greatly for some health states. As a result, the choice of HSUV can have considerable implications for the outcomes of economic evaluations. Standardization of HSUV methodology is expected to reduce variability; however, further research is recommended for assessing the sensitivity of generic preference-based measures in late-stage (metastatic) breast cancer.

On-line searching: costly or cost effective? A marketing perspective.

PubMed

Dunn, R G; Boyle, H F

1984-05-01

The value of acquiring and using information is not well understood. Decisions to purchase information are made on the basis of the perceived need for the information, the anticipated benefit of using it, and the price. The current pricing of on-line information services, which emphasizes the connect hour as the unit of price, does not relate the price of a search to the value of a search, and the education programs of on-line vendors and database suppliers concentrate on the mechanics of information retrieval rather than on the application of information to the customer's problem. The on-line information industry needs to adopt a strong marketing orientation that focuses on the needs of customers rather than the needs of suppliers or vendors.

A health economic model to determine the long-term costs and clinical outcomes of raising low HDL-cholesterol in the prevention of coronary heart disease.

PubMed

Roze, S; Liens, D; Palmer, A; Berger, W; Tucker, D; Renaudin, C

2006-12-01

The aim of this study was to describe a health economic model developed to project lifetime clinical and cost outcomes of lipid-modifying interventions in patients not reaching target lipid levels and to assess the validity of the model. The internet-based, computer simulation model is made up of two decision analytic sub-models, the first utilizing Monte Carlo simulation, and the second applying Markov modeling techniques. Monte Carlo simulation generates a baseline cohort for long-term simulation by assigning an individual lipid profile to each patient, and applying the treatment effects of interventions under investigation. The Markov model then estimates the long-term clinical (coronary heart disease events, life expectancy, and quality-adjusted life expectancy) and cost outcomes up to a lifetime horizon, based on risk equations from the Framingham study. Internal and external validation analyses were performed. The results of the model validation analyses, plotted against corresponding real-life values from Framingham, 4S, AFCAPS/TexCAPS, and a meta-analysis by Gordon et al., showed that the majority of values were close to the y = x line, which indicates a perfect fit. The R2 value was 0.9575 and the gradient of the regression line was 0.9329, both very close to the perfect fit (= 1). Validation analyses of the computer simulation model suggest the model is able to recreate the outcomes from published clinical studies and would be a valuable tool for the evaluation of new and existing therapy options for patients with persistent dyslipidemia.

[The German Statutory Accident Insurance: A successful example of a value-based healthcare structure].

PubMed

Wich, Michael; Auhuber, Thomas; Scholtysik, Dirk; Ekkernkamp, Axel

2018-02-01

In the mid-1920s Porter and others developed a reform approach for existing health care systems, aiming at a patient-focused, value-based orientation. Improving patient outcomes by attaining, preserving and restoring good health is inherently less costly than dealing with poor health. The authors of the present article will outline that the German statutory accident insurance system, which was already introduced in1884 and is of an evolving nature, reflects key elements of Porter's efficient value-based health care system. The German accident insurance system with its statutory mandate limited to the prevention and rehabilitation of work-related damage to one's health can also serve as a model for other larger health care insurance systems. Prevention and rehabilitation is pursued using all appropriate means to achieve the set goals of protecting and restoring individual health. In line with these objectives, the statutory health insurance controls the process in terms of the required care quality. The components of a complex health care system, usually managed by a variety of different institutions, are consolidated. Thus it can be ensured that in both prevention and rehabilitation all services that are necessary to keep focussing the value "individual health" rather than indemnities are applied. Copyright © 2018. Published by Elsevier GmbH.

Inhibiting the Aurora B Kinase Potently Suppresses Repopulation During Fractionated Irradiation of Human Lung Cancer Cell Lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sak, Ali, E-mail: ali.sak@uni-due.de; Stuschke, Martin; Groneberg, Michael

2012-10-01

Purpose: The use of molecular-targeted agents during radiotherapy of non-small-cell lung cancer (NSCLC) is a promising strategy to inhibit repopulation, thereby improving therapeutic outcome. We assessed the combined effectiveness of inhibiting Aurora B kinase and irradiation on human NSCLC cell lines in vitro. Methods and Materials: NSCLC cell lines were exposed to concentrations of AZD1152-hydroxyquinazoline pyrazol anilide (AZD1152-HQPA) inhibiting colony formation by 50% (IC50{sub clone}) in combination with single dose irradiation or different fractionation schedules using multiple 2-Gy fractions per day up to total doses of 4-40 Gy. The total irradiation dose required to control growth of 50% of themore » plaque monolayers (TCD50) was determined. Apoptosis, G2/M progression, and polyploidization were also analyzed. Results: TCD50 values after single dose irradiation were similar for the H460 and H661 cell lines with 11.4 {+-} 0.2 Gy and 10.7 {+-} 0.3 Gy, respectively. Fractionated irradiation using 3 Multiplication-Sign 2 Gy/day, 2 Multiplication-Sign 2 Gy/day, and 1 Multiplication-Sign 2 Gy/day schedules significantly increased TCD50 values for both cell lines grown as plaque monolayers with increasing radiation treatment time. This could be explained by a repopulation effect per day that counteracts 75 {+-} 8% and 27 {+-} 6% of the effect of a 2-Gy fraction in H460 and H661 cells, respectively. AZD1152-HQPA treatment concomitant to radiotherapy significantly decreased the daily repopulation effect (H460: 28 {+-} 5%, H661: 10 {+-} 4% of a 2-Gy fraction per day). Treatment with IC50{sub clone} AZD1152-HPQA did not induce apoptosis, prolong radiation-induced G2 arrest, or delay cell cycle progression before the spindle check point. However, polyploidization was detected, especially in cell lines without functional p53. Conclusions: Inhibition of Aurora B kinase with low AZD1152-HQPA concentrations during irradiation of NSCLC cell lines affects repopulation during radiotherapy. Thus, concomitant Aurora B kinase inhibition and irradiation may be a promising strategy for fast repopulating tumors, which are difficult to cure by dose escalation based on conventional fractionation.« less

Infrared CO line for the X 1 Sigma(+) state

NASA Technical Reports Server (NTRS)

Goorvitch, D.

1994-01-01

A complete line list with improved accuracy for all the rotation-vibration transitions of the fundamental, first, and second overtone bands up to v = 20 and J = 149 of the gradual state X 1 Sigma(+) of the seven CO isotopes -- (12)C(16)O, (13)C(16)O, (12)C(17)O, (12)C(18)O, (13)C(18)O, (14)C(16)O, and (13)c(17)O -- is made available to the astronomical community. A line list of the pure rotational transitions up to v = 5 and J = 60 is also made available for these seven isotopes. This line list contains the transition frequency, the lower state energy, the Einstein A-value, the g f-value, the transition strength at 3000 K or 1000 K for the pure rotational transitions, the expectation value of the effective dipole moment operator, and the quantum numbers of each transition. Individual partition functions are reported in the temperature range of 500 to 10,000 K. This line list is available as four text files from the author using an anonymous file transfer protocol (ftp) transfer and in computer-readable form in the AAS CD-ROM Series, Vol. 3.

Comparison of δ18O measurements in nitrate by different combustion techniques

USGS Publications Warehouse

Revesz, Kinga; Böhlke, John Karl

2002-01-01

Three different KNO3 salts with δ18O values ranging from about −31 to +54‰ relative to VSMOW were used to compare three off-line, sealed glass tube combustion methods (widely used for isotope studies) with a more recently developed on-line carbon combustion technique. All methods yielded roughly similar isotope ratios for KNO3 samples with δ18O values in the midpoint of the δ18O scale near that of the nitrate reference material IAEA-NO-3 (around +21 to +25‰). This reference material has been used previously for one-point interlaboratory and intertechnique calibrations. However, the isotope ratio scale factors by all of the off-line combustion techniques are compressed such that they are between 0.3 and 0.7 times that of the on-line combustion technique. The contraction of the δ18O scale in the off-line preparations apparently is caused by O isotope exchange between the sample and the glass combustion tubes. These results reinforce the need for nitrate reference materials with δ18O values far from that of atmospheric O2, to improve interlaboratory comparability.

Genome-enabled prediction models for yield related traits in chickpea

USDA-ARS?s Scientific Manuscript database

Genomic selection (GS) unlike marker-assisted backcrossing (MABC) predicts breeding values of lines using genome-wide marker profiling and allows selection of lines prior to field-phenotyping, thereby shortening the breeding cycle. A collection of 320 elite breeding lines was selected and phenotyped...

The Reliability and Validity of Salivation as a Measure of Individual Differences in Intrinsic Arousal. Report from the Project on Motivation and Individual Differences in Learning and Retention.

ERIC Educational Resources Information Center

Farley, Frank H.; And Others

Two studies were reported which attempted to estimate the stability and construct validity of human salivary response as a measure of individual differences (IDs) in physiological arousal. Twenty-second base line estimates and 20-second response levels to four drops of lemon juice were measured, with the former value being removed from the latter…

Parametric Phase-Sensitive Detector Using Two-cell SQUID

DTIC Science & Technology

2010-08-01

an attenuator of -20 dB. The microwave was fed into the coplanar resonator by a coplanar capacitance of 9 fF, and corresponding response was coupled...transmission line between the two coupled coplanar capacitances . With a network analyzer, the resonant frequency was confirmed to be 8.985 GHz and the...microwave directional sensors based on two-cell SQUIDs. Two SQUID circuits with different values of McCumber parameter βc have been tested. Observed

On-line Monitoring for Cutting Tool Wear Condition Based on the Parameters

NASA Astrophysics Data System (ADS)

Han, Fenghua; Xie, Feng

2017-07-01

In the process of cutting tools, it is very important to monitor the working state of the tools. On the basis of acceleration signal acquisition under the constant speed, time domain and frequency domain analysis of relevant indicators monitor the online of tool wear condition. The analysis results show that the method can effectively judge the tool wear condition in the process of machining. It has certain application value.

Research on on-line monitoring technology for steel ball's forming process based on load signal analysis method

NASA Astrophysics Data System (ADS)

Li, Ying-jun; Ai, Chang-sheng; Men, Xiu-hua; Zhang, Cheng-liang; Zhang, Qi

2013-04-01

This paper presents a novel on-line monitoring technology to obtain forming quality in steel ball's forming process based on load signal analysis method, in order to reveal the bottom die's load characteristic in initial cold heading forging process of steel balls. A mechanical model of the cold header producing process is established and analyzed by using finite element method. The maximum cold heading force is calculated. The results prove that the monitoring on the cold heading process with upsetting force is reasonable and feasible. The forming defects are inflected on the three feature points of the bottom die signals, which are the initial point, infection point, and peak point. A novel PVDF piezoelectric force sensor which is simple on construction and convenient on installation is designed. The sensitivity of the PVDF force sensor is calculated. The characteristics of PVDF force sensor are analyzed by FEM. The PVDF piezoelectric force sensor is fabricated to acquire the actual load signals in the cold heading process, and calibrated by a special device. The measuring system of on-line monitoring is built. The characteristics of the actual signals recognized by learning and identification algorithm are in consistence with simulation results. Identification of actual signals shows that the timing difference values of all feature points for qualified products are not exceed ±6 ms, and amplitude difference values are less than ±3%. The calibration and application experiments show that PVDF force sensor has good static and dynamic performances, and is competent at dynamic measuring on upsetting force. It greatly improves automatic level and machining precision. Equipment capacity factor with damages identification method depends on grade of steel has been improved to 90%.

Modelling present-day basal melt rates for Antarctic ice shelves using a parametrization of buoyant meltwater plumes

NASA Astrophysics Data System (ADS)

Lazeroms, Werner M. J.; Jenkins, Adrian; Hilmar Gudmundsson, G.; van de Wal, Roderik S. W.

2018-01-01

Basal melting below ice shelves is a major factor in mass loss from the Antarctic Ice Sheet, which can contribute significantly to possible future sea-level rise. Therefore, it is important to have an adequate description of the basal melt rates for use in ice-dynamical models. Most current ice models use rather simple parametrizations based on the local balance of heat between ice and ocean. In this work, however, we use a recently derived parametrization of the melt rates based on a buoyant meltwater plume travelling upward beneath an ice shelf. This plume parametrization combines a non-linear ocean temperature sensitivity with an inherent geometry dependence, which is mainly described by the grounding-line depth and the local slope of the ice-shelf base. For the first time, this type of parametrization is evaluated on a two-dimensional grid covering the entire Antarctic continent. In order to apply the essentially one-dimensional parametrization to realistic ice-shelf geometries, we present an algorithm that determines effective values for the grounding-line depth and basal slope in any point beneath an ice shelf. Furthermore, since detailed knowledge of temperatures and circulation patterns in the ice-shelf cavities is sparse or absent, we construct an effective ocean temperature field from observational data with the purpose of matching (area-averaged) melt rates from the model with observed present-day melt rates. Our results qualitatively replicate large-scale observed features in basal melt rates around Antarctica, not only in terms of average values, but also in terms of the spatial pattern, with high melt rates typically occurring near the grounding line. The plume parametrization and the effective temperature field presented here are therefore promising tools for future simulations of the Antarctic Ice Sheet requiring a more realistic oceanic forcing.