Characteristics and treatability of oil-bearing wastes from aluminum alloy machining operations.

PubMed

Chen, Luke; Hsieh, Chueh-Chen; Wetherbee, John; Yang, Chen-Lu

2008-04-15

Enomoto Industry Co., exclusively uses water-based cutting fluids in its aluminum alloy machining operations. Since the cost of disposal can be much greater than the cost of purchase, the treatability of spent cutting fluids is becoming a major criterion for cutting fluid selection. Samples were collected from the machining lines at Enomoto's facility to determine their characteristics and evaluate their treatability with centrifugation, chemical coagulation and electrochemical coagulation. As expected, oil and grease (O&G) and total suspended solids (TSS) are the main reasons that spent cutting fluids are prohibited from being discharged into local swage systems. The average O&G found in the spent cutting fluids is 87,354 mg/L with TSS of more than 70,000 mg/L. Both O&G and TSS are the major contributors to the high turbidity of these waste effluents. A centrifuge with a relative centrifugal force of 1318 x g, was able to reduce 60% of the turbidity. By adding the coagulant aluminum chloride, the oil-water emulsion was destabilized, and the turbidity was reduced from 3249 Formazin Attenuation Units (FAU) to around 314 FAU. With freshly generated aluminum ions in the spent cutting fluid, the electrochemical process destabilized the oil-water emulsion system. The coalesced oil droplets were adsorbed onto the highly dispersed aluminum coagulant. The oil-rich sludge that was generated in the operation was then floated to the surface, forming a blanket that was removed by skimming. The electrochemical treatment was able to reduce the turbidity to less than 14 FAU, which is the detection limit of the Hach DR/4000 UV-vis spectrophotometer.

Segmentation of oil spills in SAR images by using discriminant cuts

NASA Astrophysics Data System (ADS)

Ding, Xianwen; Zou, Xiaolin

2018-02-01

The discriminant cut is used to segment the oil spills in synthetic aperture radar (SAR) images. The proposed approach is a region-based one, which is able to capture and utilize spatial information in SAR images. The real SAR images, i.e. ALOS-1 PALSAR and Sentinel-1 SAR images were collected and used to validate the accuracy of the proposed approach for oil spill segmentation in SAR images. The accuracy of the proposed approach is higher than that of the fuzzy C-means classification method.

7 CFR 985.4 - Spearmint oil.

Code of Federal Regulations, 2011 CFR

2011-01-01

... oil. Spearmint oil, hereinafter referred to as oil, means essential oil extracted by distillation from... classes: Class 1: Oil extracted from the first cutting of Scotch Spearmint. Class 2: Oil extracted from the second cutting of Scotch Spearmint. Class 3: Oil extracted from Native Spearmint. Class 4: Oil...

7 CFR 985.4 - Spearmint oil.

Code of Federal Regulations, 2012 CFR

2012-01-01

... oil. Spearmint oil, hereinafter referred to as oil, means essential oil extracted by distillation from... classes: Class 1: Oil extracted from the first cutting of Scotch Spearmint. Class 2: Oil extracted from the second cutting of Scotch Spearmint. Class 3: Oil extracted from Native Spearmint. Class 4: Oil...

7 CFR 985.4 - Spearmint oil.

Code of Federal Regulations, 2013 CFR

2013-01-01

... oil. Spearmint oil, hereinafter referred to as oil, means essential oil extracted by distillation from... classes: Class 1: Oil extracted from the first cutting of Scotch Spearmint. Class 2: Oil extracted from the second cutting of Scotch Spearmint. Class 3: Oil extracted from Native Spearmint. Class 4: Oil...

7 CFR 985.4 - Spearmint oil.

Code of Federal Regulations, 2014 CFR

2014-01-01

... oil. Spearmint oil, hereinafter referred to as oil, means essential oil extracted by distillation from... classes: Class 1: Oil extracted from the first cutting of Scotch Spearmint. Class 2: Oil extracted from the second cutting of Scotch Spearmint. Class 3: Oil extracted from Native Spearmint. Class 4: Oil...

40 CFR 435.14 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... located beyond 3 miles from shore: Water-based drilling fluids and associated drill cuttings Free Oil No... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) OIL AND GAS EXTRACTION POINT SOURCE CATEGORY... parameter BCT effluent limitation Produced water Oil & grease The maximum for any one day shall not exceed...

40 CFR 435.14 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... located beyond 3 miles from shore: Water-based drilling fluids and associated drill cuttings Free Oil No... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) OIL AND GAS EXTRACTION POINT SOURCE CATEGORY... parameter BCT effluent limitation Produced water Oil & grease The maximum for any one day shall not exceed...

The influence on response of axial rotation of a six-group local-conductance probe in horizontal oil-water two-phase flow

NASA Astrophysics Data System (ADS)

Weihang, Kong; Lingfu, Kong; Lei, Li; Xingbin, Liu; Tao, Cui

2017-06-01

Water volume fraction is an important parameter of two-phase flow measurement, and it is an urgent task for accurate measurement in horizontal oil field development and optimization of oil production. The previous ring-shaped conductance water-cut meter cannot obtain the response values corresponding to the oil field water conductivity for oil-water two-phase flow in horizontal oil-producing wells characterized by low yield liquid, low velocity and high water cut. Hence, an inserted axisymmetric array structure sensor, i.e. a six-group local-conductance probe (SGLCP), is proposed in this paper. Firstly, the electric field distributions generated by the exciting electrodes of SGLCP are investigated by the finite element method (FEM), and the spatial sensitivity distributions of SGLCP are analyzed from the aspect of different separations between two electrodes and different axial rotation angles respectively. Secondly, the numerical simulation responses of SGLCP in horizontal segregated flow are calculated from the aspect of different water cut and heights of the water layer, respectively. Lastly, an SGLCP-based well logging instrument was developed, and experiments were carried out in a horizontal pipe with an inner diameter of 125 mm on the industrial-scale experimental multiphase flow setup in the Daqing Oilfield, China. In the experiments, the different oil-water two-phase flow, mineralization degree, temperature and pressure were tested. The results obtained from the simulation experiments and simulation well experiments demonstrate that the designed and developed SGLCP-based instrument still has a good response characteristic for measuring water conductivity under the different conditions mentioned above. The validity and reliability of obtaining the response values corresponding to the water conductivity through the designed and developed SGLCP-based instrument are verified by the experimental results. The significance of this work can provide an effective technology for measuring the water volume fraction of oil-water two-phase flow in horizontal oil-producing wells.

Aerated drilling cutting transport analysis in geothermal well

NASA Astrophysics Data System (ADS)

Wakhyudin, Aris; Setiawan, Deni; Dwi Marjuan, Oscar

2017-12-01

Aeratad drilling widely used for geothermal drilling especially when drilled into predicted production zone. Aerated drilling give better performance on preventing lost circulation problem, improving rate of penetration, and avoiding drilling fluid invasion to productive zone. While well is drilled, cutting is produced and should be carried to surface by drilling fluid. Hole problem, especially pipe sticking will occur while the cutting is not lifted properly to surface. The problem will effect on drilling schedule; non-productive time finally result more cost to be spent. Geothermal formation has different characteristic comparing oil and gas formation. Geothermal mainly has igneous rock while oil and gas mostly sedimentary rock. In same depth, formation pressure in geothermal well commonly lower than oil and gas well while formation temperature geothermal well is higher. While aerated drilling is applied in geothermal well, Igneous rock density has higher density than sedimentary rock and aerated drilling fluid is lighter than water based mud hence minimum velocity requirement to transport cutting is larger than in oil/gas well drilling. Temperature and pressure also has impact on drilling fluid (aerated) density. High temperature in geothermal well decrease drilling fluid density hence the effect of pressure and temperature also considered. In this paper, Aerated drilling cutting transport performance on geothermal well will be analysed due to different rock and drilling fluid density. Additionally, temperature and pressure effect on drilling fluid density also presented to merge.

Study on the effect of polymeric rheology modifier on the rheological properties of oil-based drilling fluids

NASA Astrophysics Data System (ADS)

Ma, C.; Li, L.; Yang, Y. P.; Hao, W. W.; Zhang, Q.; Lv, J.

2018-01-01

A new type of polymeric rheology modifier was synthesized by suspension polymerization, and the effect of rheology modifier on the rheological properties of oil-based drilling fluids was investigated. The results indicated that the obtained polymer had good capacity of improvement of shearing force of oil-based drilling fluids under high temperature and high pressure conditions. Moreover, the obtained polymer can improve the stability of oil-based drilling fluids greatly. As a result, the obtained polymer is a good rheology modifier for oil-based drilling fluids, and it can optimize oil-based drilling fluid system with good rheological properties, good static suspension ability for cuttings and environmental protection function. It can play an essential role in safe drilling jobs and improvement of drilling efficiency.

Performance of Metal Cutting on Endmills Manufactured by Cooling-Air and Minimum Quantity Lubrication Grinding

NASA Astrophysics Data System (ADS)

Inoue, Shigeru; Aoyama, Tojiro

Grinding fluids have been commonly used during the grinding of tools for their cooling and lubricating effect since the hard, robust materials used for cutting tools are difficult to grind. Grinding fluids help prevent a drop in hardness due to burning of the cutting edge and keep chipping to an absolute minimum. However, there is a heightened awareness of the need to improve the work environment and protect the global environment. Thus, the present study is aimed at applying dry grinding, cooling-air grinding, cooling-air grinding with minimum quantity lubrication (MQL), and oil-based fluid grinding to manufacturing actual endmills (HSS-Co). Cutting tests were performed by a vertical machining center. The results indicated that the lowest surface inclination values and longest tool life were obtained by cooling-air grinding with MQL. Thus, cooling-air grinding with MQL has been demonstrated to be at least as effective as oil-based fluid grinding.

Oil Based Drilling Fluid Waste: An Overview on Environmentally Persistent Pollutants

NASA Astrophysics Data System (ADS)

Siddique, Shohel; Kwoffie, Lorraine; Addae-Afoakwa, Kofi; Yates, Kyari; Njuguna, James

2017-05-01

Operational discharges of spent drilling fluid, produced water, and accumulated drill cuttings from oil and gas industry are a continuous point source of environmental pollution. To meet the strict environmental standard for waste disposal, oil and gas industry is facing a numerous challenges in technological development to ensure a clean and safe environment. Oil and gas industry generates a large amount of spent drilling fluid, produced water, and drill cuttings, which are very different in every drilling operation in terms of composition and characterisation. This review article highlights the knowledge gap in identifying the different sources of waste streams in combined drilling waste. This paper also emphasises how different chemicals turn into environmentally significant pollutants after serving great performance in oil and gas drilling operations. For instance, oil based drilling fluid performs excellent in deeper drilling and drilling in the harsh geological conditions, but ended with (produces) a significant amount of persistent toxic pollutants in the environment. This review paper provides an overview on the basic concepts of drilling fluids and their functions, sources and characterisation of drilling wastes, and highlights some environmentally significant elements including different minerals present in drilling waste stream.

Optimized Co-Processing of Algae Bio-Crude through a Petroleum Refinery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saydah, Ben; Behnke, Craig

2014-03-14

A middle distillate algal oil blend and red diesel algal oil blend from Sapphire Energy, Inc. were hydrotreated and distilled. The middle distillate feedstock blend was 8.0 wt.% biocrude and 92.0 wt.% middle distillate. The red diesel feedstock blend was 12.6 wt.% biocrude and 87.4 wt.% red diesel. During steady state, 151.4 kilograms of hydrotreated middle distillate/algal oil blend product was collected. During steady state, 312.6 kilograms of red diesel/algal oil blend hydrotreated product was collected. From the liquid product of the hydrotreated middle distillate/algal oil blend, 9.75 wt.% of the jet fuel cut is estimated to be from themore » algal oil. From the liquid product of the hydrotreated red diesel/algal oil blend, 11.3 wt.% of the diesel cut is estimated to be from the algal oil. The jet fuel cut of the middle distillate algal oil blend hydrotreated liquid product was analyzed using ASTM D1655, Standard Specification for Aviation Turbine Fuels. The diesel cut of the red diesel algal oil blend hydrotreated liquid product was analyzed using ASTM D975, Standard Specification for Diesel Fuel Oils.« less

Influence of water-miscible cutting fluid on tool wear behavior of various coated high-speed steel tools in hobbing

NASA Astrophysics Data System (ADS)

Sato, Yuta; Matsuoka, Hironori; Kubo, Akio; Ono, Hajime; Ryu, Takahiro; Qiu, Hua; Nakae, Takashi; Shuto, Shuichi; Watanabe, Suguru; Anan, Ruito

2017-04-01

This paper deals with the influence of water-miscible cutting fluid on tool life (flank wear) compared with that with dry cutting and water-insoluble cutting oil in hobbing. Experiments were conducted by simulating hobbing by fly tool cutting on a milling machine. The following results were clarified. (1) The water-miscible cutting fluid used in the test prolongs the tool life for TiN-, TiAlN-, TiSiN- and AlCrSiN-coated tools in comparison with that obtained by dry cutting and water-insoluble cutting oil. (2) It was presumed that the tool wear decreases and the tool life is improved by the lubrication effect of the synthetic lubrication additive, mineral oil and sulfuric EP additive contained in the water-miscible cutting fluid, and also by the cooling effect.

A study on the oil-based drilling cutting pyrolysis residue resource utilization by the exploration and development of shale gas.

PubMed

Wang, Chao-Qiang; Jin, Ji-Zhong; Lin, Xiao-Yan; Xiong, De-Ming; Mei, Xu-Dong

2017-07-01

Based on the requirement of national energy conservation and environmental protection, attention has been given to building an environment-friendly and resource-saving society. Shale gas oil-based drilling cutting pyrolysis residues (ODPRs) have been used as the main research object to developing new technology which can convert the residues into a harmless and recyclable material. Using the test data of ODPR, we analyze the development prospect in the building material industry and provide a scheme to utilize this particular solid-waste efficiently. Theoretically speaking, the ODPR resource utilization such as admixture of cement, making sintered brick, and non-fired brick, by the exploration and development of Fuling shale gas is feasible.

Measurement Of Multiphase Flow Water Fraction And Water-cut

NASA Astrophysics Data System (ADS)

Xie, Cheng-gang

2007-06-01

This paper describes a microwave transmission multiphase flow water-cut meter that measures the amplitude attenuation and phase shift across a pipe diameter at multiple frequencies using cavity-backed antennas. The multiphase flow mixture permittivity and conductivity are derived from a unified microwave transmission model for both water- and oil-continuous flows over a wide water-conductivity range; this is far beyond the capability of microwave-resonance-based sensors currently on the market. The water fraction and water cut are derived from a three-component gas-oil-water mixing model using the mixture permittivity or the mixture conductivity and an independently measured mixture density. Water salinity variations caused, for example, by changing formation water or formation/injection water breakthrough can be detected and corrected using an online water-conductivity tracking technique based on the interpretation of the mixture permittivity and conductivity, simultaneously measured by a single-modality microwave sensor.

Microbiological quality and other characteristics of refrigerated chicken meat in contact with cellulose acetate-based film incorporated with rosemary essential oil

PubMed Central

de Melo, Adriane Alexandre Machado; Geraldine, Robson Maia; Silveira, Miriam Fontes Araujo; Torres, Maria Célia Lopes; e Rezende, Cíntia Silva Minafra; Fernandes, Thiago Henrique; de Oliveira, Antonio Nonato

2012-01-01

Antimicrobial active packaging delays or inhibits microorganism growth in packed products, and it can be used in a variety of food systems. The objective of the present research was to develop packaging incorporated with natural antimicrobial agents (active film). The effects of the active film on the spoilage, pathogenic microorganism counts, pH and color of the refrigerated chicken breast cuts were analyzed. Cellulose acetate-based active films incorporating two concentrations (20% and 50%, v/w) of rosemary (Rosmarinus officinalis L.) essential oil were manufactured and placed in contact with the chicken breast cuts for six days. An analysis of variance and mean comparison tests (Tukey’s test, p<0.05) were performed on the results. The films that contained 20% essential oil and were intercalated with chicken breast samples did not demonstrate significant effects on the control of psychrotrophic or total coliform microorganisms during the storage period; however, the films incorporated with 50% essential oil demonstrated efficacy toward the control of coliforms during the storage of the samples (6 days, 2 ± 2ºC). The pH was related to the psychrotrophic microorganism count and was not influenced by the treatment. The color was not influenced by the time of storage or the treatment. The results demonstrate that active films incorporating 50% rosemary essential oil are effective at controlling certain microorganisms in chicken breast cuts. PMID:24031972

A comparison RSM and ANN surface roughness models in thin-wall machining of Ti6Al4V using vegetable oils under MQL-condition

NASA Astrophysics Data System (ADS)

Mohruni, Amrifan Saladin; Yanis, Muhammad; Sharif, Safian; Yani, Irsyadi; Yuliwati, Erna; Ismail, Ahmad Fauzi; Shayfull, Zamree

2017-09-01

Thin-wall components as usually applied in the structural parts of aeronautical industry require significant challenges in machining. Unacceptable surface roughness can occur during machining of thin-wall. Titanium product such Ti6Al4V is mostly applied to get the appropriate surface texture in thin wall designed requirements. In this study, the comparison of the accuracy between Response Surface Methodology (RSM) and Artificial Neural Networks (ANN) in the prediction of surface roughness was conducted. Furthermore, the machining tests were carried out under Minimum Quantity Lubrication (MQL) using AlCrN-coated carbide tools. The use of Coconut oil as cutting fluids was also chosen in order to evaluate its performance when involved in end milling. This selection of cutting fluids is based on the better performance of oxidative stability than that of other vegetable based cutting fluids. The cutting speed, feed rate, radial and axial depth of cut were used as independent variables, while surface roughness is evaluated as the dependent variable or output. The results showed that the feed rate is the most significant factors in increasing the surface roughness value followed by the radial depth of cut and lastly the axial depth of cut. In contrary, the surface becomes smoother with increasing the cutting speed. From a comparison of both methods, the ANN model delivered a better accuracy than the RSM model.

Stabilisation/solidification of synthetic petroleum drill cuttings.

PubMed

Al-Ansary, Marwa S; Al-Tabbaa, Abir

2007-03-15

This paper presents the results of an experimental investigation into the use of stabilisation/solidification (S/S) to treat synthetic drill cuttings as a pre-treatment to landfilling or for potential re-use as construction products. Two synthetic mixes were used based on average concentrations of specific contaminates present in typical drill cuttings from the North Sea and the Red Sea areas. The two synthetic drill cuttings contained similar chloride content of 2.03% and 2.13% by weight but different hydrocarbon content of 4.20% and 10.95% by weight, respectively; hence the mixes were denoted as low and high oil content mixes, respectively. A number of conventional S/S binders were tested including Portland cement (PC), lime and blast-furnace slag (BFS), in addition to novel binders such as microsilica and magnesium oxide cement. Physical, chemical and microstructural analyses were used to compare the relative performance of the different binder mixes. The unconfined compressive strength (UCS) values were observed to cover a wide range depending on the binder used. Despite the significant difference in the hydrocarbon content in the two synthetic cuttings, the measured UCS values of the mixes with the same binder type and content were similar. The leachability results showed the reduction of the synthetic drill cuttings to a stable non-reactive hazardous waste, compliant with the UK acceptance criteria for non-hazardous landfills: (a) by most of the binders for chloride concentrations, and (b) by the 20% BFS-PC and 30% PC binders for the low oil content mix. The 30% BFS-PC binder successfully reduced the leached oil concentration of the low oil content mix to inert levels. Finally, the microstructural analysis offered valuable information on the morphology and general behaviour of the mixes that were not depicted by the other tests.

Simultaneous enantioselective separation of polychlorinated biphenyls and their methyl sulfone metabolites by heart-cut MDGC: determination of enantiomeric fractions in fish oils and cow liver samples.

PubMed

Pérez-Fernández, Virginia; Castro-Puyana, María; González, María José; Marina, María Luisa; García, María Ángeles; Gómara, Belén

2012-07-01

The potential of three capillary columns based on β-cyclodextrin (i.e., Chirasil-Dex, BGB-172, and BGB-176SE) has been studied for the simultaneous enantiomeric separation of polychlorinated biphenyls (PCBs) and methylsulfonyl metabolites of PCBs (MeSO(2)-PCBs) employing a heart-cut multidimensional gas chromatographic system (heart-cut MDGC). Among the columns studied, the BGB-176SE capillary column provided the best results, allowing the simultaneous enantioselective resolution of six MeSO(2)-PCBs and six chiral PCBs; the Chirasil-Dex column did not resolve any of the studied MeSO(2)-PCBs; and a poor resolution was obtained for three MeSO(2)-PCBs when the BGB-172 column was employed. The developed method was successfully applied to two fish oil and one cow liver samples commercially available, which showed different enantioselective pattern. PCBs 91 and 176 presented a clear enrichment of the second eluted atropisomer in codfish oil, whereas in fish oil sample, slight enrichment of the first eluted atropisomer of CB45 and the second eluted atropisomer of CB136 were observed. © 2012 Wiley Periodicals, Inc.

Issues of Commonality. Volume II. Issue Analysis.

DTIC Science & Technology

1980-12-01

lubricating oil, and residual oil. 68 ° B Diesel fuel and kerosene make up what are known as the middle distillates. Jet fuels are blends from this...group of distillates which include some gasoline and some heavier oils. The range of hydrocarbons selected for this blending determines the "cut" of...the fuel. Wide-cut fuels are blended fram a wide range of hydrocarbons; narrow-cut fuels include only a small range of hydrocarbons from the

Exposure to metal-working fluids in the automobile industry and the risk of male germ cell tumours.

PubMed

Behrens, Thomas; Pohlabeln, Hermann; Mester, Birte; Langner, Ingo; Schmeisser, Nils; Ahrens, Wolfgang

2012-03-01

In a previous analysis of a case-control study of testicular cancer nested in a cohort of automobile workers, we observed an increased risk for testicular cancer among workers who had ever been involved in occupational metal-cutting tasks. We investigated whether this risk increase was due to exposure to metal-working fluids (MWF). Occupational exposure to MWF was assessed in detail using a job-specific questionnaire for metal-cutting work. We calculated ORs and associated 95% CIs individually matched for age (±2 years) and adjusted for a history of cryptorchidism by conditional logistic regression. The prevalence of exposure to MWF was 39.8% among cases and 40.1% among controls. For total germ cell tumours and seminomas we did not observe risk increases for metal-cutting tasks or occupational exposure to MWF (OR 0.95; 95% CI 0.69 to 1.32 and OR 0.88; 95% CI 0.58 to 1.35, respectively). However, dermal exposure to oil-based MWF was associated with an increased risk for non-seminomatous testicular cancer. Dermal exposure to oil-based MWF for more than 5000 h showed particularly high risk estimates (OR 4.72; 95% CI 1.48 to 15.09). Long-term dermal exposure to oil-based MWF was a risk factor for the development of non-seminomatous testicular germ cell cancer. Possible measures to reduce exposure include the introduction of engineering control measures such as venting or enclosing of machines, and enforcing the use of personal protective equipment during metal cutting.

Subsurface stratigraphy and oil fields in the Salem Limestone and associated rocks in Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, S.J.; Becker, L.E.

An area of 11 counties in southwestern Indiana was studied because (1) the subsurface geology of the Salem Limestone and associated rocks in the area contained numerous correlation discrepancies; (2) it was the locus of recent oil exploration and oil discoveries in these rocks; (3) the last subsurface study of this rock section was made in 1957; and (4) since that time, subsurface data from newly drilled petroleum-test wells have increased a hundredfold. Because of their abundance, geophysical logs were used extensively for correlation. Drill cuttings, where available, were also used in studying the rock units. The upper boundary ofmore » the Salem was based on geophysical-log correlations as supported by available drill cuttings. The lower boundary of the Salem was based on drill cuttings. Commercial oil is produced from porous calcarenite zones in the St. Louis and Salem Limestones and from coarsely crystalline limestone in the Harrodsburg Limestone. The lower part of the St. Louis Limestone yields oil from a porous carbonate rock that resembles Salem calcarenite and that we have formally named the Sission Member in the St. Louis. The Salem calcarenite facies ranges in thickness from a low of 10 percent of the total Salem in the southern part of the study area to a high of 80 percent in the northern part. Oil is produced from porous zones in the calcarenite. Oil production from the St. Louis, Salem, and Harrodsburg Limestones in Indiana amounted to 8,880,078 barrels as of December 31, 1978. Production in 1977 was 1,534,320 barrels, and production in 1978 was 1,157,450 barrels. About 80 percent of the 1977 and 1978 production came from Union-Bowman Consolidated and Sisson Fields in Gibson, Knox, and Pike counties and the Owensville North Consolidated and Mt. Carmel Consolidated Fields in Gibson County. 15 figures, 3 tables.« less

Publications - GMC 405 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 405 Publication Details Title: Geochemical analyses of oil and gas cuttings from the of Alaska, and TestAmerica Laboratories, Inc., 2012, Geochemical analyses of oil and gas cuttings (265.0 K) Keywords Geochemistry; Oil and Gas Top of Page Department of Natural Resources, Division of

NDELA and nickel modulation of triazine disposition in skin.

PubMed

Baynes, Ronald E; Brooks, James D; Barlow, Beth M; Riviere, Jim E

2005-10-01

Cutting fluids can become contaminated with metals (e.g., nickel, Ni) and nitrosamines (e.g., N-nitrosodiethanolamine, NDELA) and there is concern that these classes of contaminants can modulate dermal disposition and ultimately the toxicity of cutting fluid additives, such as irritant biocides (e.g., triazine). Biocides are added to these formulations to prevent bacterial degradation of commercial cutting fluids. The purpose of this study was to assess the dermal absorption and skin deposition of 14C-triazine when topically applied to porcine skin in an in vitro flow-through diffusion cell system as aqueous soluble oil (mineral oil, MO) or aqueous synthetic (polyethylene glycol, PEG) mixtures. 14C-Triazine mixtures were formulated with NDELA and/or Ni, or with a combination of three additional cutting fluid additives; namely, 5% linear alkylbenzene sulfonate (LAS), 5% triethanolamine (TEA) and 5% sulfurized ricinoleic acid. Neither Ni nor NDELA was absorbed during these 8-h studies. However, 14C-triazine absorption ranged from 2.72 to 3.29% dose in MO and 2.29-2.88% dose in PEG with significantly greater triazine absorption in MO than PEG when all additives and contaminates were present. The difference between these two diluents was most pronounced when NDELA and/or Ni were present in cutting fluids. These contaminants also enhanced triazine deposition on the skin surface and skin tissues especially with PEG-based mixtures. In essence, the dermal disposition of irritant biocides could be dependent on whether the worker is exposed to a soluble oil or synthetic fluid when these contaminants are present. Workers should therefore not only be concerned about dermatotoxicity of these contaminants, but also the modulated dermal disposition of cutting fluid additives when these contaminants are present in cutting fluid formulations.

Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells.

PubMed

Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

2016-10-14

First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5-60 m³/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2-60 m³/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells

PubMed Central

Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

2016-01-01

First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5–60 m3/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2–60 m3/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow. PMID:27754412

Publications - GMC 67 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

from Alaska; drill cuttings being from the following three wells: Mobil Oil Corporation Salmonberry ; drill cuttings being from the following three wells: Mobil Oil Corporation Salmonberry Lake Unit #1

Distribution of Hydroxyl Groups in Kukersite Shale Oil: Quantitative Determination Using Fourier Transform Infrared (FT-IR) Spectroscopy.

PubMed

Baird, Zachariah Steven; Oja, Vahur; Järvik, Oliver

2015-05-01

This article describes the use of Fourier transform infrared (FT-IR) spectroscopy to quantitatively measure the hydroxyl concentrations among narrow boiling shale oil cuts. Shale oil samples were from an industrial solid heat carrier retort. Reference values were measured by titration and were used to create a partial least squares regression model from FT-IR data. The model had a root mean squared error (RMSE) of 0.44 wt% OH. This method was then used to study the distribution of hydroxyl groups among more than 100 shale oil cuts, which showed that hydroxyl content increased with the average boiling point of the cut up to about 350 °C and then leveled off and decreased.

Discriminating the Mineralogical Composition in Drill Cuttings Based on Absorption Spectra in the Terahertz Range.

PubMed

Miao, Xinyang; Li, Hao; Bao, Rima; Feng, Chengjing; Wu, Hang; Zhan, Honglei; Li, Yizhang; Zhao, Kun

2017-02-01

Understanding the geological units of a reservoir is essential to the development and management of the resource. In this paper, drill cuttings from several depths from an oilfield were studied using terahertz time domain spectroscopy (THz-TDS). Cluster analysis (CA) and principal component analysis (PCA) were employed to classify and analyze the cuttings. The cuttings were clearly classified based on CA and PCA methods, and the results were in agreement with the lithology. Moreover, calcite and dolomite have stronger absorption of a THz pulse than any other minerals, based on an analysis of the PC1 scores. Quantitative analyses of minor minerals were also realized by building a series of linear and non-linear models between contents and PC2 scores. The results prove THz technology to be a promising means for determining reservoir lithology as well as other properties, which will be a significant supplementary method in oil fields.

Histograms showing variations in oil yield, water yield, and specific gravity of oil from Fischer assay analyses of oil-shale drill cores and cuttings from the Piceance Basin, northwestern Colorado

USGS Publications Warehouse

Dietrich, John D.; Brownfield, Michael E.; Johnson, Ronald C.; Mercier, Tracey J.

2014-01-01

Recent studies indicate that the Piceance Basin in northwestern Colorado contains over 1.5 trillion barrels of oil in place, making the basin the largest known oil-shale deposit in the world. Previously published histograms display oil-yield variations with depth and widely correlate rich and lean oil-shale beds and zones throughout the basin. Histograms in this report display oil-yield data plotted alongside either water-yield or oil specific-gravity data. Fischer assay analyses of core and cutting samples collected from exploration drill holes penetrating the Eocene Green River Formation in the Piceance Basin can aid in determining the origins of those deposits, as well as estimating the amount of organic matter, halite, nahcolite, and water-bearing minerals. This report focuses only on the oil yield plotted against water yield and oil specific gravity.

Enhancing safety and aroma appealing of fresh-cut fruits and vegetables using the antimicrobial and aromatic power of essential oils.

PubMed

Ayala-Zavala, J Fernando; González-Aguilar, Gustavo A; del-Toro-Sánchez, L

2009-09-01

Microbial and aroma attributes are within the most decisive factors limiting safety and sensory appealing of fresh-cut fruits and vegetables. Alternatively, several plant essential oils (EOs) are constituted of several volatile active compounds and most of them present antimicrobial potential and had different aroma profile. Considering these premises, this hypothesis article states that safety and aroma appealing of fresh-cut produce could be improved with EO treatment. EOs could prevent fresh-cut fruit decay; however, their volatile constituents could be sorbed by the produce, and according to the aroma notes of the antimicrobial oil, sensorial appealing of odor, and flavor of the treated produce might be affected positively or negatively. Specifically, garlic oil is a natural antimicrobial constituted by sulfur compounds, which are responsible for its odor and antimicrobial properties. Besides, fresh-cut tomato is a highly perishable product that needs antimicrobial agents to preserve its quality and safety for a longer period of time. From the sensorial point of view, aroma combination of garlic and tomato is a common seasoning practice in Europe and America and well accepted by consumers. Once the right combination of flavors between the EOs and the fresh-cut produce has been selected, safety and quality of the treated fruit could be improved by adding antimicrobial protection and extra aroma. Therefore, other combinations between EOs and fresh-cut produce are discussed. This approximation could reinforce the trends of natural food preservation, accomplishing the demands of the increasing sector of consumers demanding tasty and convenient fresh-cut produce, containing only natural ingredients.

Absorption of a linear (L2) and a cyclic (D4) siloxane using different oils: application to biogas treatment.

PubMed

Rojas Devia, Carolina; Subrenat, Albert

2013-01-01

Hydrophobic volatile methyl siloxanes (VMS), such as hexamethyldisiloxane (L2) and octamethylcyclotetrasiloxane (D4), present a low solubility in water. An alternative treatment by absorption into hydrophobic absorbents was therefore studied. For this purpose, three different absorbents, motor oil, cutting oil and a water-cutting oil mixture, were selected with the aim of re-using a waste product. The set of experiments was carried out in a bubble column, where parameters such as inlet concentration, residence time and temperature were studied. The best performance for the removal of both siloxanes, in terms of absorption capacity, was observed for motor oil, particularly for D4. In fact, motor oil removal efficiency for D 4 was 80%, whereas for L2 it was 60%, indicating that D 4 is more easily absorbed than L2. In the case of water-cutting oil, this showed a mass transfer enhancement from the gas phase to the liquid phase compared with water alone. Furthermore, a removal efficiency of 70% was observed for D 4, showing that the addition of an oil fraction to a water system improves the absorption of VMS. These results show that VMS absorption into oils could be a promising way to achieve their abatement.

Study on Circular Complex viewed from Environmental Systems

NASA Astrophysics Data System (ADS)

Takeguchi, Tomoo; Adachi, Katsushige; Yoshikawa, Akira; Hiratsuka, Akira; Tsujino, Ryoji; Iguchi, Manabu

In machining processes, cutting fluids are generally used for cooling and lubricating workpieces at the point cutting. However, these fluids frequently include chlorine, sulfur, phosphorus, or other additives. The chemicals not only become a mist affecting the health of workers engaged in the processing but also make the workshop environment worse. In particular, the chlorine becomes one of the causes of global warming by treating waste oil under high temperature conditions. It is furthermore said that huge cost beyond the purchase cost of oil occurs and dioxins (carcinogen) usually exist in the waste oil. Therefore, an environmentally-friendly cooling-air cutting system is required from the standpoint of green manufacturing. This system has been noted as a technique to solve the issues against the environment mentioned above. In the cooling-air cutting processing, the amount of CO2 emission shows a low value compared with the dry cutting one which uses oil. It is therefore thought that the cooling-air cutting system is a very important processing technique as an environmental countermeasure. At present, in strictly economic and environmental situations, the compatibility of the betterment of production efficiency with the improvement of environment is a subject in the actual spot of a cut processing. This study deals with the test results of cooling-air drilling performance from the viewpoint of taking green manufacturing into account. The workpiece made of die steel SKDll was manufactured by the cooling-air drilling performance at a revolution of 840 rpm and a temperature of -20°C with a high-speed steel drill (SKH56). The results were compared with those for the dry cutting performance. The main results obtained in this study are as follows: 1) The tool life for cooling-air drilling performance was about 6 times as long as that for the dry cutting performance. 2) The chip temperature for cooling-air drilling was 220°C lower than that for the dry cutting performance.

Pyrolysis characteristics and kinetics of oil-based drilling cuttings in shale gas developing

NASA Astrophysics Data System (ADS)

Huang, Chuan; Li, Tong; Xu, Tengtun; Zeng, Yunmin; Song, Xue

2018-03-01

In this paper, the thermal behavior of waste oil-based drilling cuttings (from shale gas fields in Chongqing) was examined at different heating rates ranging from 5 to 15 °C min-1 in inert atmosphere using a sync analyzer of thermogravimetry (TG) and differential scanning calorimetry (DSC). Four methods were used to analyze the distributions and variations of kinetics parameter (active energy (E) and frequency gene (A)): Coats-Redfern and other three iso-conversion rate methods (Flynn-Wall-Ozawa, Vyazovkin and Friedman). The experimental results indicated that the process consists of three steps, i.e., water evaporation, volatilization of light oil component and heavy oil cracking. TG curves moved toward higher temperature zone caused by thermal hysteresis with the increase of temperature rising rate. For volatilization of lightweight components, the E calculated by three iso-conversion rate methods changed a little with conversion, and had almost the same results as the CR method (14.39˜20.08 kJ.mol-1). For reactions of heavy oil cracking with mixed mechanism, corresponding E rose gradually with the increase of reaction time. The CR method shows nonlinear trends and the reaction models and kinetic parameters cannot be extracted from CR curves. The results by three iso-conversion methods showed that apparent activation energy was given as 155.74˜561.10 kJ.mol-1, 141.06˜524.96 kJ.mol-1 and 74.37˜605.10 kJ.mol-1, respectively.

The potential of SNP-based PCR-RFLP capillary electrophoresis analysis to authenticate and detect admixtures of Mediterranean olive oils.

PubMed

Bazakos, Christos; Khanfir, Emna; Aoun, Mariem; Spano, Thodhoraq; Zein, Zeina El; Chalak, Lamis; Riachy, Milad El; Abou-Sleymane, Gretta; Ali, Sihem Ben; Grati Kammoun, Naziha; Kalaitzis, Panagiotis

2016-07-01

Authentication and traceability of extra virgin olive oil is a challenging research task due to the complexity of fraudulent practices. In this context, the monovarietal olive oils of Protected Designation of Origin (PDO) and Protected Geographical Indication (PGI) require new tests and cutting edge analytical technologies to detect mislabeling and misleading origin. Toward this direction, DNA-based technologies could serve as a complementary to the analytical techniques assay. Single nucleotide polymorphisms are ideal molecular markers since they require short PCR analytical targets which are a prerequisite for forensic applications in olive oil sector. In the present study, a small number of polymorphic SNPs were used with an SNP-based PCR-RFLP capillary electrophoresis platform to discriminate six out of 13 monovarietal olive oils of Mediterranean origin from three different countries, Greece, Tunisia, and Lebanon. Moreover, the high sensitivity of capillary electrophoresis in combination with the DNA extraction protocol lowered the limit of detection to 10% in an admixture of Tsounati in a Koroneiki olive oil matrix. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Shock synthesized and static sintered boron nitride cutting tool

NASA Astrophysics Data System (ADS)

Araki, M.; Kuroyama, Y.

1986-05-01

Shock synthesis of wBN (wurtzite phase boron nitride) on an industrial scale was achieved by Nippon Oil & Fats and Showa Denko in 1971. It seemed that the resultant wBN powder might display excellent qualities as a cutting tool material when it was sintered under very high static pressure and temperature because of its polycrystalline nature. Attempts to produce a wBN cutting tool material were commenced by the Tokyo Institute of Technology and Nippon Oil & Fats in 1976 and commercially available wBN cutting tools were first sold in 1980. Meanwhile, a new type of explosion chamber designed to eliminate explosion sound and earth vibration problems, novel high pressure vessels and other peripheral apparatuses have been developed. Now, WURZIN (trademark for the wBN cutting tool) is used in many aspects of the steel cutting field because it is durable when cutting various steels from mild steels to superalloys under high speed, interrupt and precision cutting conditions.

An Investigation for Disposal of Drill Cuttings into Unconsolidated Sandstones and Clayey Sands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mese, Ali; Dvorkin, Jack; Shillinglaw, John

2000-09-11

This project include experimental data and a set of models for relating elastic moduli/porosity/texture and static-to-dynamic moduli to strength and failure relationships for unconsolidated sands and clayey sands. The results of the project should provide the industry with a basis for wider use of oil base drilling fluids in water sensitive formations by implementing drill cutting injection into existing wells at abandoned formations and controlling fracture geometry to prevent ground water contamination.

A database of archived drilling records of the drill cuttings piles at the North West Hutton oil platform.

PubMed

Marsh, Roy

2003-05-01

Drill cuttings piles are found underneath several hundred oil platforms in the North Sea, and are contaminated with hydrocarbons and chemical products. This study characterised the environmental risk posed by the cuttings pile at the North West Hutton (NWH) oil platform. Data on the drilling fluids and chemical products used over the platform's drilling history were transferred from archived well reports into a custom database, to which were added toxicological and safety data. Although the database contained many gaps, it established that only seven chemical products used at NWH were not in the lowest category of the Offshore Chemicals Notification Scheme, and were used in only small quantities. The study therefore supports the view that the main environmental risk posed by cuttings piles comes from hydrocarbon contamination. The (dated) well records could help future core sampling to be targeted at specific locations in the cuttings piles. Data from many platforms could also be pooled to determine generic 'discharge profiles.' Future study would benefit from the existence, in the public domain, of a standardised, 'legacy' database of chemical products.

Simulation of the mulltizones clastic reservoir: A case study of Upper Qishn Clastic Member, Masila Basin-Yemen

NASA Astrophysics Data System (ADS)

Khamis, Mohamed; Marta, Ebrahim Bin; Al Natifi, Ali; Fattah, Khaled Abdel; Lashin, Aref

2017-06-01

The Upper Qishn Clastic Member is one of the main oil-bearing reservoirs that are located at Masila Basin-Yemen. It produces oil from many zones with different reservoir properties. The aim of this study is to simulate and model the Qishn sandstone reservoir to provide more understanding of its properties. The available, core plugs, petrophysical, PVT, pressure and production datasets, as well as the seismic structural and geologic information, are all integrated and used in the simulation process. Eclipse simulator was used as a powerful tool for reservoir modeling. A simplified approach based on a pseudo steady-state productivity index and a material balance relationship between the aquifer pressure and the cumulative influx, is applied. The petrophysical properties of the Qishn sandstone reservoir are mainly investigated based on the well logging and core plug analyses. Three reservoir zones of good hydrocarbon potentiality are indicated and named from above to below as S1A, S1C and S2. Among of these zones, the S1A zone attains the best petrophysical and reservoir quality properties. It has an average hydrocarbon saturation of more than 65%, high effective porosity up to 20% and good permeability record (66 mD). The reservoir structure is represented by faulted anticline at the middle of the study with a down going decrease in geometry from S1A zone to S2 zone. It is limited by NE-SW and E-W bounding faults, with a weak aquifer connection from the east. The analysis of pressure and PVT data has revealed that the reservoir fluid type is dead oil with very low gas liquid ratio (GLR). The simulation results indicate heterogeneous reservoir associated with weak aquifer, supported by high initial water saturation and high water cut. Initial oil in place is estimated to be around 628 MM BBL, however, the oil recovery during the period of production is very low (<10%) because of the high water cut due to the fractures associated with many faults. Hence, secondary and tertiary methods are needed to enhance the oil recovery. Water flooding is recommended as the first step of oil recovery enhancement by changing some of high water cut wells to injectors.

49 CFR 230.116 - Oil tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Oil tanks. 230.116 Section 230.116 Transportation... Locomotive Tanks § 230.116 Oil tanks. The oil tanks on oil burning steam locomotives shall be maintained free from leaks. The oil supply pipe shall be equipped with a safety cut-off device that: (a) Is located...

49 CFR 230.116 - Oil tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Oil tanks. 230.116 Section 230.116 Transportation... Locomotive Tanks § 230.116 Oil tanks. The oil tanks on oil burning steam locomotives shall be maintained free from leaks. The oil supply pipe shall be equipped with a safety cut-off device that: (a) Is located...

49 CFR 230.116 - Oil tanks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Oil tanks. 230.116 Section 230.116 Transportation... Locomotive Tanks § 230.116 Oil tanks. The oil tanks on oil burning steam locomotives shall be maintained free from leaks. The oil supply pipe shall be equipped with a safety cut-off device that: (a) Is located...

49 CFR 230.116 - Oil tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Oil tanks. 230.116 Section 230.116 Transportation... Locomotive Tanks § 230.116 Oil tanks. The oil tanks on oil burning steam locomotives shall be maintained free from leaks. The oil supply pipe shall be equipped with a safety cut-off device that: (a) Is located...

Essential Oils of Hyptis pectinata Chemotypes: Isolation, Binary Mixtures and Acute Toxicity on Leaf-Cutting Ants.

PubMed

Feitosa-Alcantara, Rosana B; Bacci, Leandro; Blank, Arie F; Alves, Péricles B; Silva, Indira Morgana de A; Soares, Caroline A; Sampaio, Taís S; Nogueira, Paulo Cesar de L; Arrigoni-Blank, Maria de Fátima

2017-04-12

Leaf-cutting ants are pests of great economic importance due to the damage they cause to agricultural and forest crops. The use of organosynthetic insecticides is the main form of control of these insects. In order to develop safer technology, the objective of this work was to evaluate the formicidal activity of the essential oils of two Hyptis pectinata genotypes (chemotypes) and their major compounds on the leaf-cutting ants Acromyrmex balzani Emery and Atta sexdens rubropilosa Forel. Bioassays of exposure pathways (contact and fumigation) and binary mixtures of the major compounds were performed. The major compounds identified in the essential oils of H. pectinata were β-caryophyllene, caryophyllene oxide and calamusenone. The essential oils of H. pectinata were toxic to the ants in both exposure pathways. Essential oils were more toxic than their major compounds alone. The chemotype calamusenone was more toxic to A. balzani in both exposure pathways. A. sexdens rubropilosa was more susceptible to the essential oil of the chemotype β-caryophyllene in both exposure pathways. In general, the binary mixtures of the major compounds resulted in additive effect of toxicity. The essential oils of H. pectinata is a raw material of great potential for the development of new insecticides.

Drill cuttings mount formation study

NASA Astrophysics Data System (ADS)

Teh, Su Yean; Koh, Hock Lye

2014-07-01

Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

Performance evaluation of Titanium nitride coated tool in turning of mild steel

NASA Astrophysics Data System (ADS)

Srinivas, B.; Pramod Kumar, G.; Cheepu, Muralimohan; Jagadeesh, N.; kumar, K. Ravi; Haribabu, S.

2018-03-01

The growth in demand for bio-gradable materials is opened as a venue for using vegetable oils, coconut oils etc., as alternate to the conventional coolants for machining operations. At present in manufacturing industries the demand for surface quality is increasing rapidly along with dimensional accuracy and geometric tolerances. The present study is influence of cutting parameters on the surface roughness during the turning of mild steel with TiN coated carbide tool using groundnut oil and soluble oil as coolants. The results showed vegetable gave closer surface finish compares with soluble oil. Cutting parameters has been optimized with Taguchi technique. In this paper, the main objective is to optimize the cutting parameters and reduce surface roughness analogous to increase the tool life by apply the coating on the carbide inserts. The cost of the coating is more, but economically efficient than changing the tools frequently. The plots were generated and analysed to find the relationship between them which are confirmed by performing a comparison study between the predicted results and theoretical results.

Effects of Microwave Radiation on Oil Recovery

NASA Astrophysics Data System (ADS)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Slicing of Silicon into Sheet Material: Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1979-01-01

Testing of low cost low suspension power slurry vehicles is presented. Cutting oils are unlikely to work, but a mineral oil with additives should be workable. Two different abrasives were tested. A cheaper silicon carbide from Norton gave excellent results except for excessive kerf loss: the particles were too big. An abrasive treated for lubricity showed no lubricity improvement in mineral oil vehicle. The bounce fixture was tested for the first time under constant cut rate conditions (rather than constant force). Although the cut was not completed before the blades broke, the blade lifetime of thin (100 micrometer) blades was 120 times the lifetime without the fixture. The large prototype saw completed a successful run, producing 90% cutting yield (849 wafers) at 20 wafers/cm. Although inexperience with large numbers of wafers caused cleaning breakage to reduce this yield to 74%, the yield was high enough that the concept of the large saw is proven workable.

Natural Fiber Cut Machine Semi-Automatic Linear Motion System for Empty Fiber Bunches: Re-designing for Local Use

NASA Astrophysics Data System (ADS)

Asfarizal; Kasim, Anwar; Gunawarman; Santosa

2017-12-01

Empty Palm bunches of fiber is local ingredient in Indonesia that easy to obtain. Empty Palm bunches of fiber can be obtained from the palm oil industry such as in West Pasaman. The character of the empty Palm bunches of fiber that is strong and pliable has high-potential for particle board. To transform the large quantities of fiber become particles in size 0-10 mm requires a specially designed cut machine. Therefore, the machine is designed in two-stage system that is mechanical system, structure and cutting knife. Components that have been made, assembled and then tested to reveal the ability of the machine to cut. The results showed that the straight back and forth motion cut machine is able to cut out the empty oil palm bunches of fiber with a length 0-1 cm, 2 cm, 8 cm and the surface of the cut is not stringy. The cutting capacity is at a length of 2 cm in the result 24.4 (kg/h) and 8 cm obtained results of up to 84 (kg/h)

Effect of Water Cut on Pressure Drop of Oil (D130) -Water Flow in 4″Horizontal Pipe

NASA Astrophysics Data System (ADS)

Basha, Mehaboob; Shaahid, S. M.; Al-Hems, Luai M.

2018-03-01

The oil-water flow in pipes is a challenging subject that is rich in physics and practical applications. It is often encountered in many oil and chemical industries. The pressure gradient of two phase flow is still subject of immense research. The present study reports pressure measurements of oil (D130)-water flow in a horizontal 4″ diameter stainless steel pipe at different flow conditions. Experiments were carried out for different water cuts (WC); 0-100%. Inlet oil-water flow rates were varied from 4000 to 8000 barrels-per-day in steps of 2000. It has been found that the frictional pressure drop decreases for WC = 0 - 40 %. With further increase in WC, friction pressure drop increases, this could be due to phase inversion.

GammaScorpion: mobile gamma-ray tomography system for early detection of basal stem rot in oil palm plantations

NASA Astrophysics Data System (ADS)

Abdullah, Jaafar; Hassan, Hearie; Shari, Mohamad Rabaie; Mohd, Salzali; Mustapha, Mahadi; Mahmood, Airwan Affendi; Jamaludin, Shahrizan; Ngah, Mohd Rosdi; Hamid, Noor Hisham

2013-03-01

Detection of the oil palm stem rot disease Ganoderma is a major issue in estate management and production in Malaysia. Conventional diagnostic techniques are difficult and time consuming when using visual inspection, and destructive and expensive when based on the chemical analysis of root or stem tissue. As an alternative, a transportable gamma-ray computed tomography system for the early detection of basal stem rot (BSR) of oil palms due to Ganoderma was developed locally at the Malaysian Nuclear Agency, Kajang, Malaysia. This system produces high quality tomographic images that clearly differentiate between healthy and Ganoderma infected oil palm stems. It has been successfully tested and used to detect the extent of BSR damage in oil palm plantations in Malaysia without the need to cut down the trees. This method offers promise for in situ inspection of oil palm stem diseases compared to the more conventional methods.

Publications - GMC 173 | Alaska Division of Geological & Geophysical

Science.gov Websites

wells: Colorado Oil and Gas Core Hole #1, 890' - 3570'; and Colorado Oil and Gas Core Hole #2, 4520 cuttings from the following 2 wells: Colorado Oil and Gas Core Hole #1, 890' - 3570'; and Colorado Oil and

Long- and short-term effects of smothering and burial by drill cuttings on calcareous algae in a static-renewal test.

PubMed

Reynier, Márcia V; Tâmega, Frederico T S; Daflon, Sarah D A; Santos, Maurício A B; Coutinho, Ricardo; Figueiredo, Marcia A O

2015-07-01

Discharge of drill cuttings into the ocean during drilling of offshore oil wells can impact benthic communities through an increase in the concentrations of suspended particles in the water column and sedimentation of particles on the seafloor around the drilling installation. The present study assessed effects of water-based drill cuttings, barite, bentonite, and natural sediments on shallow- and deep-water calcareous algae in short-term (30 d) and long-term (90 d) experiments, using 2 species from Peregrino's oil field at Campos Basin, Brazil: Mesophyllum engelhartii and Lithothamnion sp. The results were compared with the shallow-water species Lithothamnion crispatum. Smothering and burial exposures were simulated. Oxygen production and fluorescence readings were recorded. Although less productive, M. engelhartii was as sensitive to stress as Lithothamnion sp. Mesophyllum engelhartii was sensitive to smothering by drill cuttings, barite, and bentonite after 60 d of exposure and was similarly affected by natural sediments after 90 d. These results indicate that smothering by sediments caused physical effects that might be attributable to partial light attenuation and partial restriction on gas exchange but did not kill the calcareous algae in the long term. However, 1-mo burial by either natural sediments or drill cuttings was sufficient after 60 d for both species to reduce oxygen production, and the algae were completely dead under both sources of sediments. © 2015 SETAC.

The Effect of Heat Treatment on Residual Stress and Machining Distortions in Advanced Nickel Base Disk Alloys

NASA Technical Reports Server (NTRS)

Gayda, John

2001-01-01

This paper describes an extension of NASA's AST and IDPAT Programs which sought to predict the effect of stabilization heat treatments on residual stress and subsequent machining distortions in the advanced disk alloy, ME-209. Simple "pancake" forgings of ME-209 were produced and given four heat treats: 2075F(SUBSOLVUS)/OIL QUENCH/NO AGE; 2075F/OIL QUENCH/1400F@8HR;2075F/OIL QUENCH/1550F@3HR/l400F@8HR; and 2160F(SUPERSOLVUS)/OIL QUENCH/1550F@3HR/ 1400F@8HR. The forgings were then measured to obtain surface profiles in the heat treated condition. A simple machining plan consisting of face cuts from the top surface followed by measurements of the surface profile opposite the cut were made. This data provided warpage maps which were compared with analytical results. The analysis followed the IDPAT methodology and utilized a 2-D axisymmetric, viscoplastic FEA code. The analytical results accurately tracked the experimental data for each of the four heat treatments. The 1550F stabilization heat treatment was found to significantly reduce residual stresses and subsequent machining distortions for fine grain (subsolvus) ME209, while coarse grain (supersolvus) ME209 would require additional time or higher stabilization temperatures to attain the same degree of stress relief.

Oil field experiments of microbial improved oil recovery in Vyngapour, West Siberia, Russia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murygina, V.P.; Mats, A.A.; Arinbasarov, M.U.

1995-12-31

Experiments on microbial improved oil recovery (MIOR) have been performed in the Vyngapour oil field in West Siberia for two years. Now, the product of some producing wells of the Vyngapour oil field is 98-99% water cut. The operation of such wells approaches an economic limit. The nutritious composition containing local industry wastes and sources of nitrogen, phosphorus and potassium was pumped into an injection well on the pilot area. This method is called {open_quotes}nutritional flooding.{close_quotes} The mechanism of nutritional flooding is based on intensification of biosynthesis of oil-displacing metabolites by indigenous bacteria and bacteria from food industry wastes inmore » the stratum. 272.5 m{sup 3} of nutritious composition was introduced into the reservoir during the summer of 1993, and 450 m3 of nutritious composition-in 1994. The positive effect of the injections in 1993 showed up in 2-2.5 months and reached its maximum in 7 months after the injections were stopped. By July 1, 1994, 2,268.6 tons of oil was produced over the base variant, and the simultaneous water extraction reduced by 33,902 m{sup 3} as compared with the base variant. The injections in 1994 were carried out on the same pilot area.« less

Health Hazard Evaluation Report HETA 83-107-1574, Dana Corporation, Fort Wayne, Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parrish, R.G.; Wallingford, K.M.

1985-04-01

Environmental and breathing-zone samples of cutting fluids and oils were analyzed at Dana Corporation, Fort Wayne, Indiana in May, 1983. The survey was requested by a company representative to evaluate the cause of dermatitis among machine-tool operators. A cutting fluid used at the facility was thought to be the cause of the dermatitis. Medical questionnaires were administered to 95 workers. Company dispensary records were reviewed. N-nitrosodimethylamine and triethanolamine were detected in new and used cutting fluid samples. Nickel, chromium, and zinc were detected in a sample of used cutting oil residue. Chloromethyl-phenol was found in two cutting fluid mix samples.more » The authors conclude that a health hazard exists at the facility. The skin problems appear to be related to exposure to cutting fluids and solvents in general, rather than a specific agent. Recommendations include using protective clothing, using waterless hand cleaners instead of solvents, and avoiding contact with chlorothene.« less

Publications - GMC 276 | Alaska Division of Geological & Geophysical

Science.gov Websites

Company USA OCS Y-0804 (Orion #1),Husky Oil NPR Operations Kuyanak #1, Husky Oil Operations South Barrow #16, Husky Oil Operations West Dease #1 cuttings and U.S. Navy South Barrow #3 Authors: DGSI, Inc -0804 (Orion #1),Husky Oil NPR Operations Kuyanak #1, Husky Oil Operations South Barrow #16, Husky Oil

Practical aspects of chemometrics for oil spill fingerprinting.

PubMed

Christensen, Jan H; Tomasi, Giorgio

2007-10-26

Tiered approaches for oil spill fingerprinting have evolved rapidly since the 1990s. Chemometrics provides a large number of tools for pattern recognition, calibration and classification that can increase the speed and the objectivity of the analysis and allow for more extensive use of the available data in this field. However, although the chemometric literature is extensive, it does not focus on practical issues that are relevant to oil spill fingerprinting. The aim of this review is to provide a framework for the use of chemometric approaches in tiered oil spill fingerprinting and to provide clear-cut practical details and experiences that can be used by the forensic chemist. The framework is based on methods for initial screening, which include classification of samples into oil type, detection of non matches and of weathering state, and detailed oil spill fingerprinting, in which a more rigorous matching of an oil spill sample to suspected source oils is obtained. This review is intended as a tutorial, and is based on two examples of initial screening using respectively gas chromatography with flame ionization detection and fluorescence spectroscopy; and two of detailed oil spill fingerprinting where gas chromatography-mass spectrometry data are analyzed according to two approaches: The first relying on sections of processed chromatograms and the second on diagnostic ratios.

Mechanical impact tests of materials in oxygen effects of contamination. [Teflon, stainless steel, and aluminum

NASA Technical Reports Server (NTRS)

Ordin, P. M.

1980-01-01

The effect of contaminants on the mechanical impact sensitivity of Teflon, stainless steel, and aluminum in a high-pressure oxygen environment was investigated. Uncontaminated Teflon did not ignite under the test conditions. The liquid contaminants - cutting oil, motor lubricating oil, and toolmaker dye - caused Teflon to ignite. Raising the temperature lowered the impact energy required for ignition. Stainless steel was insensitive to ignition under the test conditions with the contaminants used. Aluminum appeared to react without contaminants under certain test conditions; however, contamination with cutting oil, motor lubricating oil, and toolmakers dye increased the sensitivity of aluminum to mechanical impact. The grit contaminants silicon dioxide and copper powder did not conclusively affect the sensitivity of aluminum.

Detergent-dispersant additives based on high-molecular-weight alkylphenols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kulieva, K.N.; Namazova, I.I.; Ismailova, N.D.

1988-09-01

This article describes the synthesis and investigation of Mannich bases produced for alkylphenols, obtained in turn from ethylene oligomers. These oligomers are the still bottoms from distillation products of high-temperature oligomerization of ethylene in the presence of triethylaluminum. Two narrow cuts obtained from the distillation of oligomer fraction were used to study the influence of ethylene oligomer molecular weight on the properties of the additives. The additives were blended in DS-11 oil to evaluate their detergency-dispersancy and other properties. Comparison blends were made with succinimide additives based on the same ethylene oligomers. The Mannich bases give improvements in the oxidationmore » resistance, anticorrosion properties, and detergency-dispersancy of the DS-11 diesel oil.« less

Modelling of oil spills in confined maritime basins: The case for early response in the Eastern Mediterranean Sea.

PubMed

Alves, Tiago M; Kokinou, Eleni; Zodiatis, George; Lardner, Robin; Panagiotakis, Costas; Radhakrishnan, Hari

2015-11-01

Oil spill models are combined with bathymetric, meteorological, oceanographic, and geomorphological data to model a series of oil spill accidents in the Eastern Mediterranean Sea. A total of 104 oil spill simulations, computed for 11 different locations in the Levantine Basin, show that oil slicks will reach the coast of Cyprus in four (4) to seven (7) days in summer conditions. Oil slick trajectories are controlled by prevailing winds and current eddies. Based on these results, we support the use of chemical dispersants in the very few hours after large accidental oil spills. As a corollary, we show shoreline susceptibility to vary depending on: a) differences in coastline morphology and exposure to wave action, b) the existence of uplifted wave-cut platforms, coastal lagoons and pools, and c) the presence of tourist and protected environmental areas. Mitigation work should take into account the relatively high susceptibility of parts of the Eastern Mediterranean. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Publications - GMC 248 | Alaska Division of Geological & Geophysical

Science.gov Websites

from cuttings of the following Copper River basin oil and gas exploratory wells: Aledo Oil Co. Eureka #2 (2000' - 8545'); and Mobil Oil Corp. Salmonberry Lake Unit #2 (1500' - 7900') Authors: DGSI, Inc the following Copper River basin oil and gas exploratory wells: Aledo Oil Co. Eureka #2 (2000' - 8545

Freon, T-B1 cutting fluid

NASA Technical Reports Server (NTRS)

Peters, R. L.

1969-01-01

Improved cutting fluid completely controls the heat generated from machining operations, thus providing longer tool life. Fluid is especially useful in the working of plastics and replaces less efficient contaminating oils.

By-pass filters : taking your fleet the extra mile

DOT National Transportation Integrated Search

2000-01-01

There has been an industry-wide push over the last few years to extend oil drain intervals on fleet equipment. This industry demand is an effort to reduce downtime, reduce waste oil generation, and cut maintenance costs. Extended oil drain intervals ...

40 CFR 435.14 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... located beyond 3 miles from shore: Water-based drilling fluids and associated drill cuttings Free Oil No... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Effluent limitations guidelines... control technology (BCT). 435.14 Section 435.14 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

40 CFR 435.14 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... located beyond 3 miles from shore: Water-based drilling fluids and associated drill cuttings Free Oil No... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Effluent limitations guidelines... control technology (BCT). 435.14 Section 435.14 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

Environmental performance, mechanical and microstructure analysis of concrete containing oil-based drilling cuttings pyrolysis residues of shale gas.

PubMed

Wang, Chao-Qiang; Lin, Xiao-Yan; He, Ming; Wang, Dan; Zhang, Si-Lan

2017-09-15

The overall objective of this research project is to investigate the feasibility of incorporating oil-based drilling cuttings pyrolysis residues (ODPR) and fly ash serve as replacements for fine aggregates and cementitious materials in concrete. Mechanical and physical properties, detailed environmental performances, and microstructure analysis were carried out. Meanwhile, the early hydration process and hydrated products of ODPR concrete were analyzed with X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The results indicated that ODPR could not be categorize into hazardous wastes. ODPR had specific pozzolanic characteristic and the use of ODPR had certain influence on slump and compressive strength of concrete. The best workability and optimal compressive strength were achieved with the help of 35% ODPR. Environmental performance tests came to conclusion that ODPR as recycled aggregates and admixture for the preparation of concrete, from the technique perspective, were the substance of mere environmental contamination. Copyright © 2017 Elsevier B.V. All rights reserved.

Physicochemical determinants of linear alkylbenzene sulfonate (LAS) disposition in skin exposed to aqueous cutting fluid mixtures.

PubMed

Baynes, Ronald E; Brooks, James D; Barlow, Beth M; Riviere, Jim E

2002-06-01

Linear alkylbenzene sulfonate (LAS) is added to cutting fluid formulations to enhance the performance of metal machining operations, but this surfactant can cause contact dermatitis in workers involved in these operations. The purpose of this study was to determine how cutting fluid additives influence dermal disposition of 14C-LAS in mineral oil- or polyethylene glycol 200 (PEG)-based mixtures when topically applied to silastic membranes and porcine skin in an in vitro flow-through diffusion cell system. 14C-LAS mixtures were formulated with three commonly used cutting fluid additives; 0 or 2% triazine (TRI), 0 or 5% triethanolamine (TEA), and 0 or 5% sulfurized ricinoleic acid (SRA). LAS absorption was limited to less than a 0.5% dose and the additives in various combinations influenced the physicochemical characteristics of the dosing mixture. LAS was more likely to partition into the stratum corneum (SC) in mineral oil mixtures, and LAS absorption was significantly greater in the complete mixture. TRI enhanced LAS transport, and the presence of SRA decreased LAS critical micelle concentration (CMC) which reduced LAS monomers available for transport. TEA increased mixture viscosity, and this may have negated the apparent enhancing properties of TRI in several mixtures. In summary, physicochemical interactions in these mixtures influenced availability of LAS for absorption and distribution in skin, and could ultimately influence toxicological responses in skin.

Comparative efficacy of cedarwood oil and xylene in hematoxylin and eosin staining procedures: An experimental study.

PubMed

Indu, Sudip; Ramesh, V; Indu, Priyanka Chakravarty; Prashad, Karthikshree V; Premalatha, B; Ramadoss, K

2014-07-01

Xylene is used as a clearing agent in hematoxylin and eosin (H and E) staining of tissue sections in routine histopathology based diagnosis. However, the hazards associated with exposure to xylene are of concern. Numerous solutions mainly essential oils have been evaluated in the past as clearing agents, which can possibly be substituted for xylene during the routine tissue processing. The aim of this study is to compare the efficacy of essential oil (cedarwood oil), as a possible replacement for xylene in H and E staining procedures. The study was carried out in the Department of Oral Pathology and Microbiology. Thirty paraffin blocks of the routine biopsy specimen were retrieved from the department archives. The cedarwood oil was procured from organic and essential oil dealer in the local market. Two to three paraffin sections of four micron thickness were cut from each of the 30 paraffin blocks of processed tissue specimens, were subjected to different clearing agents: Essential oil (8% cedarwood oil) or xylene and stained with H and E stain. The stained sections were scored based on nuclear and cytoplasmic details, clarity and uniformity of staining. Significant correlation was observed between cedarwood oil and xylene in terms of the three staining quality parameters assessed. We conclude that cedarwood oil can be an effective, eco-friendly and safe alternative to xylene as a clearing agent in the histopathological laboratory.

Publications - GMC 277 | Alaska Division of Geological & Geophysical

Science.gov Websites

from the following: Shell Oil Company Kustatan Ridge #1, Shell Oil Company Middle River State #1 , Superior Oil Three Mile Creek State #1, Texas International Pet. Corp. Pretty Creek State #1 Authors reflectance analyses for Cook Inlet well cuttings from the following: Shell Oil Company Kustatan Ridge #1

Publications - GMC 174 | Alaska Division of Geological & Geophysical

Science.gov Websites

wells: Colorado Oil and Gas Yakutat #1, (1095' - 9295'); Colorado Oil and Gas Yakutat #2 (1980' - 11720 '); Colorado Oil and Gas Yakutat #3 (6780' - 10730') Authors: Pawlewicz, Mark Publication Date: 1990 Publisher , Mark, 1990, Vitrinite reflectance data of cuttings from the following 3 wells: Colorado Oil and Gas

Essential Oil of Aristolochia trilobata: Synthesis, Routes of Exposure, Acute Toxicity, Binary Mixtures and Behavioral Effects on Leaf-Cutting Ants.

PubMed

de Oliveira, Bruna Maria S; Melo, Carlisson R; Alves, Péricles B; Santos, Abraão A; Santos, Ane Caroline C; Santana, Alisson da S; Araújo, Ana Paula A; Nascimento, Pedro E S; Blank, Arie F; Bacci, Leandro

2017-02-25

Plants of the genus Aristolochia have been frequently reported as important medicinal plants. Despite their high bioactive potential, to date, there are no reports of their effects on leaf-cutting ants. Therefore, the present study aimed to evaluate the insecticidal activity of the essential oil of Aristolochia trilobata and its major components on Atta sexdens and Acromyrmex balzani , two species of leaf-cutting ants. The bioassays were performed regarding routes of exposure, acute toxicity, binary mixtures of the major components and behavioral effects. Twenty-five components were identified in the essential oil of A. trilobata using a gas chromatographic system equipped with a mass spectrometer and a flame ionization detector. The components found in higher proportions were sulcatyl acetate, limonene, p -cymene and linalool. The essential oil of A. trilobata and its individual major components were efficient against A. balzani and A. sexdens workers when applied by fumigation. These components showed fast and efficient insecticidal activity on ants. The components acted synergistically and additively on A. balzani and A. sexdens , respectively, and caused a strong repellency/irritability in the ants. Thus, our results demonstrate the great potential of the essential oil of A. trilobata and its major components for the development of new insecticides.

OPFLEX®

EPA Pesticide Factsheets

Technical product bulletin: this miscellaneous oil spill control agent used in cleanups is an open-celled elastomeric sorbent. The foam can be cut and fabricated into various shapes in order to absorb oil in different scenarios.

Maximize Liquid Oil Production from Shale Oil and Gas Condensate Reservoirs by Cyclic Gas Injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, James; Li, Lei; Yu, Yang

The current technology to produce shale oil reservoirs is the primary depletion using fractured wells (generally horizontal wells). The oil recovery is less than 10%. The prize to enhance oil recovery (EOR) is big. Based on our earlier simulation study, huff-n-puff gas injection has the highest EOR potential. This project was to explore the potential extensively and from broader aspects. The huff-n-puff gas injection was compared with gas flooding, water huff-n-puff and waterflooding. The potential to mitigate liquid blockage was also studied and the gas huff-n-puff method was compared with other solvent methods. Field pilot tests were initiated but terminatedmore » owing to the low oil price and the operator’s budget cut. To meet the original project objectives, efforts were made to review existing and relevant field projects in shale and tight reservoirs. The fundamental flow in nanopores was also studied.« less

Edible coating as carrier of antimicrobial agents to extend the shelf life of fresh-cut apples

USDA-ARS?s Scientific Manuscript database

Edible coatings with antimicrobial agents can extend shelf-life of fresh-cut fruits. The effect of lemongrass, oregano oil and vanillin incorporated in apple puree-alginate edible coatings, on shelf-life of fresh-cut 'Fuji' apples, was investigated. Coated apples were packed in air filled polypropyl...

43 CFR 3593.1 - Core or test hole cores, samples, cuttings.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... (d) When drilling on lands with potential for encountering high pressure oil, gas or geothermal... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Core or test hole cores, samples, cuttings...) EXPLORATION AND MINING OPERATIONS Bore Holes and Samples § 3593.1 Core or test hole cores, samples, cuttings...

43 CFR 3593.1 - Core or test hole cores, samples, cuttings.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (d) When drilling on lands with potential for encountering high pressure oil, gas or geothermal... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Core or test hole cores, samples, cuttings...) EXPLORATION AND MINING OPERATIONS Bore Holes and Samples § 3593.1 Core or test hole cores, samples, cuttings...

43 CFR 3593.1 - Core or test hole cores, samples, cuttings.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (d) When drilling on lands with potential for encountering high pressure oil, gas or geothermal... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Core or test hole cores, samples, cuttings...) EXPLORATION AND MINING OPERATIONS Bore Holes and Samples § 3593.1 Core or test hole cores, samples, cuttings...

43 CFR 3593.1 - Core or test hole cores, samples, cuttings.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (d) When drilling on lands with potential for encountering high pressure oil, gas or geothermal... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Core or test hole cores, samples, cuttings...) EXPLORATION AND MINING OPERATIONS Bore Holes and Samples § 3593.1 Core or test hole cores, samples, cuttings...

Attenuation of laser radiation by the flame of burning hydrocarbons and efficiency of remote cutting of metals

NASA Astrophysics Data System (ADS)

Gvozdev, S. V.; Glova, A. F.; Dubrovskii, V. Yu; Durmanov, S. T.; Krasyukov, A. G.; Lysikov, A. Yu; Smirnov, G. V.; Pleshkov, V. M.

2017-12-01

Mobile laser technological complex MLTC-20 with radiation power 20 kW and radiation wavelength 1.07 μm created in SRC RF TRINITI on the base of a three cw fiber Yb lasers is used successfully at remote cutting of the metalworks at carrying out of the emergency-reduction works on the out of control gas wells. In this work the results of the investigation of the possibility and the efficiency of laser radiation application for remote cutting of metals on the emergency oil wells have been presented. Measurements of the mean absorption coefficient of the radiation of a cw fiber Yb laser under its propagation in a flame of burning oil in dependence on radiation intensity have been carried out. It was shown that at the intensity ~104 W/cm2 the absorption coefficient traverses the maximum where its value is equal to ~0.1 cm-1, and at the intensity increasing to the values 105 - 106 W/cm2 it stabilizes on a small level ~5·10-3 - 10-2 cm-1. It is established that the maximal velocity and the efficiency of remote cutting of the steel plates with a thickness up to 10 mm by the radiation with the intensity 106 W/cm2 exceed these factors at the intensity 104 W/cm2. The possibility of the efficient remote cutting of steel plate with a thickness of 60 mm by laser radiation having the power 7.5 kW and the intensity 105 W/cm2 has been demonstrated.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Towprayoon, S.; Kuntrangwattana, S.

Cutting oil wastewater from an iron and steel factory was applied to the soil windrow. Self-remediation was then compared with remediation with acclimatized indigenous microbes. The incremental reduction rate of the microorganisms and hydrocarbon-degradable microbes was slower in self-remediation than in the latter treatment. Within 30 days, when the acclimatized indigenous microbes were used, there was a significant reduction of the contaminated hydrocarbons, while self-remediation took longer to reduce to the same concentration. Various nitrogen sources were applied to the soil pile, namely, organic compost, chemical fertilizer, ammonium sulfate, and urea. The organic compost induced a high yield of hydrocarbon-degradablemore » microorganisms, but the rate at which the cutting oil in the soil decreased was slower than when other nitrogen sources were used. The results of cutting oil degradation studied by gas chromatography showed the absence of some important hydrocarbons. The increment of the hydrocarbon-degradable microbes in the land treatment ecosystem does not necessarily correspond to the hydrocarbon reduction efficiency. 3 refs., 3 figs.« less

Evaluation of stability and viscosity measurement of emulsion from oil from production in northern oilfield in Thailand

NASA Astrophysics Data System (ADS)

Juntarasakul, O.; Maneeintr, K.

2018-04-01

Emulsion is normally present in oil due to the mixing occurring during oil recovery. The formation of emulsion can cause some problems in production and transportation. Viscosity and stability of emulsion play a key roles in oil transportation and separation to meet sales specification. Therefore, the aims of this research are to measure the viscosity of oil an emulsion and to evaluate the stability of emulsion of light oil from Fang oilfield in Thailand. The parameters of this study are temperature, shear rate and water cut ranging from 50 to 80 °C, 3.75 to 70 s-1 and 0 to 60%, respectively. These effects of parameters on viscosity and stability of emulsion are required for the design of the process and to increase oil production with various conditions. The results shows that viscosity decreases as temperature and shear rate increase. In contrast, viscosity becomes higher when water cut is lower. Furthermore, droplet sizes of water-in-oil emulsion at different conditions are investigated the stability of emulsion. The droplet sizes become smaller when high shear rate is applied and emulsion becomes more stable. Furthermore, correlations are developed to predict the viscosity and stability of the oil and emulsion from Thailand.

Influence of two dietary fats on the composition of emu oil and meat.

PubMed

Beckerbauer, L M; Thiel-Cooper, R; Ahn, D U; Sell, J L; Parrish, F C; Beitz, D C

2001-02-01

Male and female emus were fed a diet rich in saturated fat (beef tallow) or a diet rich in unsaturated fat (soybean oil) until they weighed about 35 kg. Samples of subcutaneous and retroperitoneal adipose tissues and samples of six major meat cuts were taken for determination of composition. Emus fed the two different diets grew at similar rates, but the male emus had a higher percentage of carcass fat. The adipose tissue cells from males were larger than those from females. All six meat cuts averaged 2.2% fat, with the regular filet having the most and the inside and outside drums the least. Cholesterol concentration of all sizes of meat cuts averaged 32.2 mg/100 g meat. Diet did not influence cholesterol content of the rendered oil. Fan filets had the greatest concentration of cholesterol, and the inside and outside drums had the least. Source of dietary fat had no effect on fat and cholesterol content of the meats. Meat from emus fed beef tallow was more tender and juicy. Fan filets were the most tender meat, had the least intense flavor, and were the most flavorful. Untrained panelists were able to discriminate between emu meat and beef. Source of dietary fat did not influence the fatty acid compositions of the meats. As expected, the soybean oil-fed emus produced oil that was more polyunsaturated than did the tallow-fed emus.

78 FR 25695 - Notice of Intent To Seek Approval To Conduct an Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-02

.... Remove seeds received at mill, hulls produced, linters produced (first, second cut, and mill run), stocks of crude oil, hulls, linters (first, second cut, and mill run). Remove flaxseed seeds crushed, stocks...

Publications - GMC 323 | Alaska Division of Geological & Geophysical

Science.gov Websites

West Fish Creek No. 1 from cuttings (5520'-5550', 5570'-5600', 5660'-5690' and 5730'-5770') Authors Oil NPR Operations Inc. US Navy West Fish Creek No. 1 from cuttings (5520'-5550', 5570'-5600', 5660

Environmental impacts of produced water and drilling waste discharges from the Norwegian offshore petroleum industry.

PubMed

Bakke, Torgeir; Klungsøyr, Jarle; Sanni, Steinar

2013-12-01

Operational discharges of produced water and drill cuttings from offshore oil and gas platforms are a continuous source of contaminants to continental shelf ecosystems. This paper reviews recent research on the biological effects of such discharges with focus on the Norwegian Continental Shelf. The greatest concern is linked to effects of produced water. Alkylphenols (AP) and polyaromatic hydrocarbons (PAH) from produced water accumulate in cod and blue mussel caged near outlets, but are rapidly metabolized in cod. APs, naphtenic acids, and PAHs may disturb reproductive functions, and affect several chemical, biochemical and genetic biomarkers. Toxic concentrations seem restricted to <2 km distance. At the peak of discharge of oil-contaminated cuttings fauna disturbance was found at more than 5 km from some platforms, but is now seldom detected beyond 500 m. Water-based cuttings may seriously affect biomarkers in filter feeding bivalves, and cause elevated sediment oxygen consumption and mortality in benthic fauna. Effects levels occur within 0.5-1 km distance. The stress is mainly physical. The risk of widespread, long term impact from the operational discharges on populations and the ecosystem is presently considered low, but this cannot be verified from the published literature. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Fischer Assays of Oil Shale Drill Cores and Rotary Cuttings from the Piceance Basin, Colorado - 2009 Update

USGS Publications Warehouse

Mercier, Tracey J.; Brownfield, Michael E.; Johnson, Ronald C.; Self, Jesse G.

1998-01-01

This CD-ROM includes updated files containing Fischer assays of samples of core holes and cuttings from exploration drill holes drilled in the Eocene Green River Formation in the Piceance Basin of northwestern Colorado. A database was compiled that includes more than 321,380 Fischer assays from 782 boreholes. Most of the oil yield data were analyzed by the former U.S. Bureau of Mines oil shale laboratory in Laramie, Wyoming, and some analyses were made by private laboratories. Location data for 1,042 core and rotary holes, oil and gas tests, as well as a few surface sections are listed in a spreadsheet and included in the CD-ROM. These assays are part of a larger collection of subsurface information held by the U.S. Geological Survey, including geophysical and lithologic logs, water data, and chemical and X-ray diffraction analyses having to do with the Green River oil shale deposits in Colorado, Wyoming, and Utah. Because of an increased interest in oil shale, this CD-ROM disc containing updated Fischer assay data for the Piceance Basin oil shale deposits in northwestern Colorado is being released to the public.

Study of the Effect of Modes of Electroerosion Treatment on the Microstructure and Accuracy of Precision Sizes of Small Parts

NASA Astrophysics Data System (ADS)

Korobova, N. V.; Aksenenko, A. Yu.; Bashevskaya, O. S.; Nikitin, A. A.

2016-01-01

Results of a study of the effect of the parameters of electroerosion treatment in a GF Agie Charmilles CUT 1000 OilTech wire-cutting bench on the size accuracy, the quality of the surface layer of cuts, and the microstructure of the surface of the treated parts are presented.

Lighting with Less Wattage.

ERIC Educational Resources Information Center

American School and University, 1981

1981-01-01

Schools in Wilton (Connecticut) cut electric consumption 39 percent by replacing existing lamps with new types of energy saving lamps. Fuel oil consumption dropped 53 percent largely through attention paid to the operation of boilers and oil burners. (Author/MLF)

Publications - GMC 92 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

Oil Company Beaver Creek Unit #4 well Authors: Makada, R. Publication Date: 1988 Publisher: Alaska , Vitrinite reflectance data of ditch cuttings from the Marathon Oil Company Beaver Creek Unit #4 well: Alaska

Research on the identification of inefficient and invalid circulation in ultra-high water cut stage

NASA Astrophysics Data System (ADS)

Han, Shaoxin

2018-06-01

After oil field entered into ultra-high water cut stage, big channels are formed in some oil and water wells and lead to the inefficient and ineffective circulation of injected water, which not only inhibit the increase of recovery ratio of oil and gas, but also cause the waste of resources. This article selects three static parameters and four dynamic parameters which can perform inefficient and ineffective circulation characteristics between oil and water wells, integrates the fuzzy mathematics theory, establishes fuzzy comprehensive evaluation model to identify the inefficient and ineffective circulation wells in the research area, on this basis, inefficient and ineffective circulation position is further determined through the logging curve characteristics and logging ratio method, the identification of inefficient and ineffective circulation "determine well and layer" is achieved, and provide powerful basis for governance work of inefficient and ineffective circulation.

An unusual and persistent contamination of drinking water by cutting oil.

PubMed

Rella, R; Sturaro, A; Parvoli, G; Ferrara, D; Doretti, L

2003-02-01

Drinking water contamination by materials, such as cutting oil, used to set up pipelines is an uncommon but possible event. This paper describes the analytical procedures used to identify the components of that contaminant in drinking water. Volatile and semi-volatile chemical species, responsible for an unpleasant taste and odour, were recognised by solid phase microextraction and GC/MS techniques. Among the volatile compounds, the presence of xylenes, bornyl acetate and diphenyl ether was confirmed by certificate standards and quantified in the most contaminated samples.

Following basal stem rot in young oil palm plantings.

PubMed

Panchal, G; Bridge, P D

2005-01-01

The PCR primer GanET has previously been shown to be suitable for the specific amplification of DNA from Ganoderma boninense. A DNA extraction and PCR method has been developed that allows for the amplification of the G. boninense DNA from environmental samples of oil palm tissue. The GanET primer reaction was used in conjunction with a palm-sampling programme to investigate the possible infection of young palms through cut frond base surfaces. Ganoderma DNA was detected in frond base material at a greater frequency than would be expected by comparison with current infection levels. Comparisons are made between the height of the frond base infected, the number of frond bases infected, and subsequent development of basal stem rot. The preliminary results suggest that the development of basal stem rot may be more likely to occur when young lower frond bases are infected.

30 CFR 250.469 - What other well records could I be required to submit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations... reports identifying microscopic fossils by depth and/or washed samples of drill cuttings that you normally...

Turbodrills and innovative PDC bits economically drilled hard formations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boudreaux, R.C.; Massey, K.

1994-03-28

The use of turbodrills and polycrystalline diamond compact (PDC) bits with an innovative, tracking cutting structure has improved drilling economics in medium and hard formations in the Gulf of Mexico. Field results have confirmed that turbodrilling with trackset PDC bits reduced drilling costs, compared to offset wells. The combination of turbodrills and trackset bits has been used successfully in a broad range of applications and with various drilling parameters. Formations ranging from medium shales to hard, abrasive sands have been successfully and economically drilled. The tools have been used in both water-based and oil-based muds. Additionally, the turbo-drill and tracksetmore » PDC bit combination has been stable on directional drilling applications. The locking effect of the cutting structure helps keep the bit on course.« less

Experimental Study on the Flow Regimes and Pressure Gradients of Air-Oil-Water Three-Phase Flow in Horizontal Pipes

PubMed Central

Al-Hadhrami, Luai M.; Shaahid, S. M.; Tunde, Lukman O.; Al-Sarkhi, A.

2014-01-01

An experimental investigation has been carried out to study the flow regimes and pressure gradients of air-oil-water three-phase flows in 2.25 ID horizontal pipe at different flow conditions. The effects of water cuts, liquid and gas velocities on flow patterns and pressure gradients have been studied. The experiments have been conducted at 20°C using low viscosity Safrasol D80 oil, tap water and air. Superficial water and oil velocities were varied from 0.3 m/s to 3 m/s and air velocity varied from 0.29 m/s to 52.5 m/s to cover wide range of flow patterns. The experiments were performed for 10% to 90% water cuts. The flow patterns were observed and recorded using high speed video camera while the pressure drops were measured using pressure transducers and U-tube manometers. The flow patterns show strong dependence on water fraction, gas velocities, and liquid velocities. The observed flow patterns are stratified (smooth and wavy), elongated bubble, slug, dispersed bubble, and annular flow patterns. The pressure gradients have been found to increase with the increase in gas flow rates. Also, for a given superficial gas velocity, the pressure gradients increased with the increase in the superficial liquid velocity. The pressure gradient first increases and then decreases with increasing water cut. In general, phase inversion was observed with increase in the water cut. The experimental results have been compared with the existing unified Model and a good agreement has been noticed. PMID:24523645

Experimental study on the flow regimes and pressure gradients of air-oil-water three-phase flow in horizontal pipes.

PubMed

Al-Hadhrami, Luai M; Shaahid, S M; Tunde, Lukman O; Al-Sarkhi, A

2014-01-01

An experimental investigation has been carried out to study the flow regimes and pressure gradients of air-oil-water three-phase flows in 2.25 ID horizontal pipe at different flow conditions. The effects of water cuts, liquid and gas velocities on flow patterns and pressure gradients have been studied. The experiments have been conducted at 20 °C using low viscosity Safrasol D80 oil, tap water and air. Superficial water and oil velocities were varied from 0.3 m/s to 3 m/s and air velocity varied from 0.29 m/s to 52.5 m/s to cover wide range of flow patterns. The experiments were performed for 10% to 90% water cuts. The flow patterns were observed and recorded using high speed video camera while the pressure drops were measured using pressure transducers and U-tube manometers. The flow patterns show strong dependence on water fraction, gas velocities, and liquid velocities. The observed flow patterns are stratified (smooth and wavy), elongated bubble, slug, dispersed bubble, and annular flow patterns. The pressure gradients have been found to increase with the increase in gas flow rates. Also, for a given superficial gas velocity, the pressure gradients increased with the increase in the superficial liquid velocity. The pressure gradient first increases and then decreases with increasing water cut. In general, phase inversion was observed with increase in the water cut. The experimental results have been compared with the existing unified Model and a good agreement has been noticed.

Comparative evaluation of physicochemical properties of jatropha curcas seed oil for coolant-lubricant application

NASA Astrophysics Data System (ADS)

Murad, Muhamad Nasir; Sharif, Safian; Rahim, Erween Abd.; Abdullah, Rozaini

2017-09-01

Increased attention to environmental issues due to industrial activities has forced the authorities raise awareness and implement regulations to reduce the use of mineral oil. Some vegetable oils unexplored or less explored, particularly the non-edible oils such as Jatropha curcas oil (JCO) and others. Physicochemical properties of JCO is compared with others edible oils, synthetic ester and fatty alcohol to obtain a viable alternative in metal cutting fluids. The oil was found to show the suitability of properties for coolant-lubricant applications in term of its physicochemical properties and better in flash point and viscosity value.

Application of 1D and 2D MFR reactor technology for the isolation of insecticidal and anti-microbial properties from pyrolysis bio-oils.

PubMed

Hossain, Mohammad M; Scott, Ian M; Berruti, Franco; Briens, Cedric

2016-12-01

Valuable chemicals can be separated from agricultural residues by chemical or thermochemical processes. The application of pyrolysis has already been demonstrated as an efficient means to produce a liquid with a high concentration of desired product. The objective of this study was to apply an insect and microorganism bioassay-guided approach to separate and isolate pesticidal compounds from bio-oil produced through biomass pyrolysis. Tobacco leaf (Nicotianata bacum), tomato plant (Solanum lycopersicum), and spent coffee (Coffea arabica) grounds were pyrolyzed at 10°C/min from ambient to 565°C using the mechanically fluidized reactor (MFR). With one-dimensional (1D) MFR pyrolysis, the composition of the product vapors varied as the reactor temperature was raised allowing for the selection of the temperature range that corresponds to vapors with a high concentration of pesticidal properties. Further product separation was performed in a fractional condensation train, or 2D MFR pyrolysis, thus allowing for the separation of vapor components according to their condensation temperature. The 300-400°C tobacco and tomato bio-oil cuts from the 1D MFR showed the highest insecticidal and anti-microbial activity compared to the other bio-oil cuts. The 300-350 and 350-400°C bio-oil cuts produced by 2D MFR had the highest insecticidal activity when the bio-oil was collected from the 210°C condenser. The tobacco and tomato bio-oil had similar insecticidal activity (LC 50 of 2.1 and 2.2 mg/mL) when the bio-oil was collected in the 210°C condenser from the 300-350°C reactor temperature gases. The 2D MFR does concentrate the pesticidal products compared to the 1D MFR and thus can reduce the need for further separation steps such as solvent extraction.

Critical Elements in Reservoir Rocks of Produced Fluids Nevada and Utah August 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simmons, Stuart

Critical and trace element data for drill cuttings from Beowawe, Dixie Valley, and Roosevelt Hot Springs-Blundell geothermal production fields, for drill cuttings from Uinta basin producing oil-gas wells, and from outcrops in the Sevier Thermal Anomaly-Utah.

Different Diversity and Distribution of Archaeal Community in the Aqueous and Oil Phases of Production Fluid From High-Temperature Petroleum Reservoirs.

PubMed

Liang, Bo; Zhang, Kai; Wang, Li-Ying; Liu, Jin-Feng; Yang, Shi-Zhong; Gu, Ji-Dong; Mu, Bo-Zhong

2018-01-01

To get a better knowledge on how archaeal communities differ between the oil and aqueous phases and whether environmental factors promote substantial differences on microbial distributions among production wells, we analyzed archaeal communities in oil and aqueous phases from four high-temperature petroleum reservoirs (55-65°C) by using 16S rRNA gene based 454 pyrosequencing. Obvious dissimilarity of the archaeal composition between aqueous and oil phases in each independent production wells was observed, especially in production wells with higher water cut, and diversity in the oil phase was much higher than that in the corresponding aqueous phase. Statistical analysis further showed that archaeal communities in oil phases from different petroleum reservoirs tended to be more similar, but those in aqueous phases were the opposite. In the high-temperature ecosystems, temperature as an environmental factor could have significantly affected archaeal distribution, and archaeal diversity raised with the increase of temperature ( p < 0.05). Our results suggest that to get a comprehensive understanding of petroleum reservoirs microbial information both in aqueous and oil phases should be taken into consideration. The microscopic habitats of oil phase, technically the dispersed minuscule water droplets in the oil could be a better habitat that containing the indigenous microorganisms.

Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile–butadiene rubber latex

PubMed Central

Krzemińska, Sylwia; Rzymski, Władysław M.; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

2016-01-01

Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile–butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves. PMID:26757889

Metagenome enrichment approach used for selection of oil-degrading bacteria consortia for drill cutting residue bioremediation.

PubMed

Guerra, Alaine B; Oliveira, Jorge S; Silva-Portela, Rita C B; Araújo, Wydemberg; Carlos, Aline C; Vasconcelos, Ana Tereza R; Freitas, Ana Teresa; Domingos, Yldeney Silva; de Farias, Mirna Ferreira; Fernandes, Glauber José Turolla; Agnez-Lima, Lucymara F

2018-04-01

Drill cuttings leave behind thousands of tons of residues without adequate treatment, generating a large environmental liability. Therefore knowledge about the microbial community of drilling residue may be useful for developing bioremediation strategies. In this work, samples of drilling residue were enriched in different culture media in the presence of petroleum, aiming to select potentially oil-degrading bacteria and biosurfactant producers. Total DNA was extracted directly from the drill cutting samples and from two enriched consortia and sequenced using the Ion Torrent platform. Taxonomic analysis revealed the predominance of Proteobacteria in the metagenome from the drill cuttings, while Firmicutes was enriched in consortia samples. Functional analysis using the Biosurfactants and Biodegradation Database (BioSurfDB) revealed a similar pattern among the three samples regarding hydrocarbon degradation and biosurfactants production pathways. However, some statistical differences were observed between samples. Namely, the pathways related to the degradation of fatty acids, chloroalkanes, and chloroalkanes were enriched in consortia samples. The degradation colorimetric assay using dichlorophenolindophenol as an indicator was positive for several hydrocarbon substrates. The consortia were also able to produce biosurfactants, with biosynthesis of iturin, lichnysin, and surfactin among the more abundant pathways. A microcosms assay followed by gas chromatography analysis showed the efficacy of the consortia in degrading alkanes, as we observed a reduction of around 66% and 30% for each consortium in total alkanes. These data suggest the potential use of these consortia in the bioremediation of drilling residue based on autochthonous bioaugmentation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Topical Report Tantalum – 2.5% Tungsten Machinability Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

L. J. Lazarus

2009-09-02

Protection Association (NFPA). NFPA 484, Standard for Combustible Metals, Chapter 9 Tantalum and Annex E, supplemental Information on Tantalum require cutting oil be used when machining tantalum because it burns at such a high temperature that it breaks down the water in a water-based metalworking fluid (MWF). The NFPA guide devotes approximately 20 pages to this material. The Kansas City Plant (KCP) uses Fuchs Lubricants Ecocut Base 44 LVC as a MWF. This is a highly chlorinated oil with a high flash point (above 200° F). The chlorine is very helpful in preventing BUE (Built Up Edge) that occurs frequentlymore » with this very gummy material. The Ecocut is really a MWF additive that Fuchs uses to add chlorinated fats to other non-chlorinated MWF.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilkinson, T.P.

A new solids control system, consisting of four new shakers and a dryer in parallel all discharging into another dryer, significantly reduced the oil on the cuttings in a nine-well offshore drilling program. Cleaned, slurrified cuttings were then discharged overboard. In November 1994, Oiltools (Europe) Ltd. received contracts to upgrade the solids control systems on Sedco Forex`s Sedco 711 and Sovereign Explorer semisubmersible drilling vessels. Sedco Forex required systems that would meet the reduced oil-on-cuttings (OOC) disposal limit of less than 80 g/kg set by the operator, while staying efficient and economical to operate and maintain. In addition, all solidsmore » were required to be slurrified for pumping overboard to ensure dispersal away from the subsea center. This article highlights the equipment used and the savings realized on the Sovereign Explorer after the first three wells of a nine-well program.« less

Publications - GMC 199 | Alaska Division of Geological & Geophysical

Science.gov Websites

(2,770' and 6,520') and of core (8,242') from Gulf Oil Corporation Colville Delta State #1 well, and of of cuttings (2,770' and 6,520') and of core (8,242') from Gulf Oil Corporation Colville Delta State

CHIP MORPHOLOGY AND HOLE SURFACE TEXTURE IN THE DRILLING OF CAST ALUMINUM ALLOYS. (R825370C057)

EPA Science Inventory

The effects of cutting fluid and other process variables on chip morphology when drilling cast aluminium alloys are investigated. The effects of workpiece material, speed, feed, hole depth, cutting-fluid presence and percentage oil concentration, workpiece temperature, drill t...

Technological study on reducing blast-hole rate during laser cutting oil pipe

NASA Astrophysics Data System (ADS)

Deng, Qiansong; Yang, Weihong; Tang, Xiahui; Peng, Hao; Qin, Yingxiong

2012-03-01

In this paper, a laser cutting technology for the oil pipes with the thickness of 10mm, the diameter of 142mm and the material of N80 has been developed, in order to reduce the high hole-blast rate in processing. Experiments are taken on the Rofin DC025 slab CO2 laser cutting system and a set of flexible fixtures. The reasons of forming blast-hole have been analyzed, and the influences of technique parameters on blast-hole rate have been studied, such as laser power, pulse frequency, laser delay, focus position and oxygen pressure. The results show that the blast-hole rate can be controlled lower than 5% at the conditions of laser power 1500W, laser delay 5s, pulse frequency 180Hz, the oxygen pressure 0.6 kg/cm2, focus length 190mm, nozzle diameter 1.5mm.

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR RANGE MANAGEMENT (4000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

43 CFR 3931.80 - Core or test hole samples and cuttings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MANAGEMENT OF OIL SHALE.... The records must include a log of all strata penetrated and conditions encountered, such as water, gas... operation or any deposit of oil, gas, other mineral substances, or ground water. (c) Operators may convert...

Tumeric oil as the antioxidation agent in edible coating film

NASA Astrophysics Data System (ADS)

Ahmad, N. A.; Sharif, Z. I. M.; Jai, J.; Yusof, N. M.; Mustapha, F. A.

2018-03-01

Turmeric oil (TO) has been studied for its potential as an antioxidation agent in starch edible coating for fresh cut apples and its degree of oxidation was analysed. TO incorporate with starch edible coating was examined using FT-IR Spectroscopy to determine the presence of secondary metabolites. The presence of alcohol and aromatic ring in the edible coating film proved that the secondary metabolites from TO were existed. The fresh cut apples were underwent the sensory test and six out of ten panellist concluded that coated fresh cut apples have good appearance and surface colour. Fresh cut apples were coated with edible coating incorporated with different concentrations of TO (uncoated, 0μL, 5μL, 10μL, 15μL. Percentage weight loss for 15μL were the least which were 1.98% (day 6) and 3.95% (day 12). Colour measurement were done for few days and it shows that the total colour difference (ΔΕ) for 15μL were the lowest. Thus, the oxidation activities for 15μL is the slowest compared to the others. These can be proved through the degree of oxidation analysis using UV-Vis spectroscopy. Uncoated fresh cut apples have the highest degree of oxidation while those with 15μL have the lowest. This study can be illustrated that the oxidation activities of fresh cut apples could be postponed using edible film incorporated with TO.

Forensic fingerprinting of oil-spill hydrocarbons in a methanogenic environment-Mandan, ND and Bemidji, MN

USGS Publications Warehouse

Hostettler, F.D.; Wang, Y.; Huang, Y.; Cao, W.; Bekins, B.A.; Rostad, C.E.; Kulpa, C.F.; Laursen, Andrew E.

2007-01-01

In recent decades forensic fingerprinting of oil-spill hydrocarbons has emerged as an important tool for correlating oils and for evaluating their source and character. Two long-term hydrocarbon spills, an off-road diesel spill (Mandan, ND) and a crude oil spill (Bemidji, MN) experiencing methanogenic biodegradation were previously shown to be undergoing an unexpected progression of homologous n-alkane and n-alkylated cyclohexane loss. Both exhibited degradative losses proceeding from the high-molecular-weight end of the distributions, along with transitory concentration increases of lower-molecular-weight homologs. Particularly in the case of the diesel fuel spill, these methanogenic degradative patterns can result in series distributions that mimic lower cut refinery fuels or admixture with lower cut fuels. Forensic fingerprinting in this long-term spill must therefore rely on more recalcitrant series, such as polycyclic aromatic hydrocarbon or drimane sesquiterpane profiles, to prove if the spilled oil is single-sourced or whether there is verifiable admixture with other extraneous refinery fuels. Degradation processes impacting n-alkanes and n-alkylated ring compounds, which make these compounds unsuitable for fingerprinting, nevertheless are of interest in understanding methanogenic biodegradation. Copyright ?? Taylor & Francis Group, LLC.

Effects of drill cuttings on larvae of the cold-water coral Lophelia pertusa

NASA Astrophysics Data System (ADS)

Järnegren, Johanna; Brooke, Sandra; Jensen, Henrik

2017-03-01

Fossil fuel consumption is predicted to dominate energy needs until at least 2040. To make up for reduced production from maturing fields, oil and gas exploration activities on the Norwegian continental shelf have greatly increased over the past several years. Strict emission controls have resulted in a substantial reduction in the release of hazardous chemicals. However, because of the increased exploration the discharges of water-based drill cuttings and muds have increased substantially, temporarily increasing water column sediment loads. The stony coral Lophelia pertusa is the most widely distributed and well-studied of the structure forming cold water corals (CWC) and it thrives in Norwegian waters where many reefs are located in the vicinity of oil platforms or exploration areas. This species provides habitat for a diverse and abundant assemblage of invertebrates and fishes, including commercially valuable species. High sediment loads are known to negatively affect adult corals, but impacts on the early life history stages are unknown. We investigated the effects of a range of drill cutting concentrations (0.5-640 ppm) on larvae of L. pertusa at ages five days and 15-20 days. One set of experiments was conducted in static experimental chambers that exposed larvae to decreasing concentrations over time, and the other maintained continuous drill cutting concentrations for the duration of the experiment (24 h). Increased sediment load for a duration of 24 h caused significant larval mortality, but there was an age-dependent difference in sensitivity of larvae. Younger larvae were significantly more susceptible to lower concentrations of drill cuttings than older larvae, while the older larvae were significantly more affected at higher concentrations. Five day old larvae were affected at treatment concentration 40 ppm. The larval cilia became clogged, preventing the larvae from swimming actively and ultimately causing mortality. Larvae of many species use cilia for swimming and feeding, so negative impacts of increased sediment may not be limited to corals.

Coated carbide drill performance under soluble coconut oil lubricant and nanoparticle enhanced MQL in drilling AISI P20

NASA Astrophysics Data System (ADS)

Jamil, N. A. M.; Azmi, A. I.; Fairuz, M. A.

2016-02-01

This research experimentally investigates the performance of a TiAlN coated carbide drill bit in drilling AISI P20 through two different kinds of lubricants, namely; soluble coconut oil (SCO) and nanoparticle-enhanced coconut oil (NECO) under minimum quantity lubrication system. The tool life and tool wear mechanism were studied using various cutting speeds of 50, 100 and 150 m/min with a constant feed of 0.01 mm/rev. Since the flank wear land was not regular along the cutting edge, the average flank wear (VB) was measured at several points using image analysis software. The drills were inspected using a scanning electron microscope to further elucidate the wear mechanism. The result indicates that drilling with the nanoparticle- enhanced lubricant was better in resisting the wear and improving the drill life to some extent

30 CFR 250.469 - What other well records could I be required to submit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Modify and Well Records § 250.469 What.../or washed samples of drill cuttings that you normally maintain for paleontological determinations...

Publications - GMC 134 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Oil Corporation Moquawkie #1 well Authors: Edison, T.A. Publication Date: 1989 Publisher: Alaska , Vitrinite reflectance data of cuttings and core from the Mobil Oil Corporation Moquawkie #1 well: Alaska

Publications - GMC 168 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Home Oil Co. Bush Fed #1 well Authors: Pawlewicz, Mark Publication Date: 1990 Publisher: Alaska , Vitrinite reflectance data of cuttings (5390'-14850') from the Home Oil Co. Bush Fed #1 well: Alaska

1986 Flood Control and Navigation Maps of the Mississippi River

DTIC Science & Technology

1987-01-01

Higgerson Ldg.. Mo. 4 911.3 10 781.5 Grand Lake, Ark. (lake and town) 28 Hodge Ldg.. La. (Diamond Cut-off) 34 IB 667.5 Grand Lake Cul-ofl 28 511.0 Hog...La. Tellier Island. Ark. Tennemo Ldg., Tenn. Tennessee Bar. Miss. Terrapin Neck Cut-oil Terrene Ldg.. Miss. Texas. La. The Jump Theima Ldg

Publications - GMC 290 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 290 Publication Details Title: Organic carbon and rock-eval pyrolysis data of cuttings from Reference Unknown, 1999, Organic carbon and rock-eval pyrolysis data of cuttings from the Husky Oil NPR Products Report Report Information gmc290.pdf (177.0 K) Keywords Pyrolysis; Rock-Eval Pyrolysis Top of Page

Molecular imprinted hydrogel polymer (MIHP) as microbial immobilization media in artificial produced water treatment

NASA Astrophysics Data System (ADS)

Kardena, E.; Ridhati, S. L.; Helmy, Q.

2018-01-01

Produced water generated during oil and gas exploration and drilling, consists of many chemicals which used in drilling process. The production of produced water is over three fold of the oil production. The water-cut has increased over time and continues to do so because the fraction of oil in the reservoir decreases and it is more difficult to get the oil out from an old oil-field. It therefore requires more sea water to be injected in order to force the oil out; hence more produced water is generated. Produced water can pollute the environment if it is not treated properly. In this research, produced water will be treated biologically using bacterial consortium which is isolated from petroleum processing facility with Molecular Imprinted Hydrogel Polymer (MIHP) for microbial immobilization media. Microbial growth rate is determined by measuring the MLVSS and hydrogel mass, also by SEM-EDS analysis. SEM-EDS analysis is an analysis to evidence the presence of microbe trapped in hydrogel, and also to determine the types and weight of the molecules of hydrogel. From this research, suspended microbial growth rate was found at 0.1532/days and attached microbial growth rate was 0.3322/days. Furthermore, based on SEM analysis, microbe is entrapped inside the hydrogel. Effectiveness of microbial degradation activity was determined by measuring organic materials as COD. Based on COD measurement, degradation rate of organic materials in wastewater is 0.3089/days, with maximum COD removal efficiency of 76.67%.

Molecular Weight Cut-Off and Structural Analysis of Vacuum-Assisted Titania Membranes for Water Processing

PubMed Central

Abd Jalil, Siti Nurehan; Wang, David K.; Yacou, Christelle; Motuzas, Julius; Smart, Simon; Diniz da Costa, João C.

2016-01-01

This work investigates the structural formation and analyses of titania membranes (TM) prepared using different vacuum exposure times for molecular weight (MW) cut-off performance and oil/water separation. Titania membranes were synthesized via a sol-gel method and coated on macroporous alumina tubes followed by exposure to a vacuum between 30 and 1200 s and then calcined at 400 °C. X-ray diffraction and nitrogen adsorption analyses showed that the crystallite size and particle size of titania increased as a function of vacuum time. All the TM membranes were mesoporous with an average pore diameter of ~3.6 nm with an anatase crystal morphology. Water, glucose, sucrose, and polyvinylpyrrolidone with 40 and 360 kDa (PVP-40 kDa and PVP-360 kDa) were used as feed solutions for MW cut-off and hexadecane solution for oil filtration investigation. The TM membranes were not able to separate glucose and sucrose, thus indicating the membrane pore sizes are larger than the kinetic diameter of sucrose of 0.9 nm, irrespective of vacuum exposure time. They also showed only moderate rejection (20%) of the smaller PVP-40 kDa, however, all the membranes were able to obtain an excellent rejection of near 100% for the larger PVP-360 kDa molecule. Furthermore, the TM membranes were tested for the separation of oil emulsions with a high concentration of oil (3000 ppm), reaching high oil rejections of more than 90% of oil. In general, the water fluxes increased with the vacuum exposure time indicating a pore structural tailoring effect. It is therefore proposed that a mechanism of pore size tailoring was formed by an interconnected network of Ti–O–Ti nanoparticles with inter-particle voids, which increased as TiO2 nanoparticle size increased as a function of vacuum exposure time, and thus reduced the water transport resistance through the TM membranes. PMID:28774057

Well logging evaluation of water-flooded layers and distribution rule of remaining oil in marine sandstone reservoirs of the M oilfield in the Pearl River Mouth basin

NASA Astrophysics Data System (ADS)

Li, Xiongyan; Qin, Ruibao; Gao, Yunfeng; Fan, Hongjun

2017-03-01

In the marine sandstone reservoirs of the M oilfield the water cut is up to 98%, while the recovery factor is only 35%. Additionally, the distribution of the remaining oil is very scattered. In order to effectively assess the potential of the remaining oil, the logging evaluation of the water-flooded layers and the distribution rule of the remaining oil are studied. Based on the log response characteristics, the water-flooded layers can be qualitatively identified. On the basis of the mercury injection experimental data of the evaluation wells, the calculation model of the initial oil saturation is built. Based on conventional logging data, the evaluation model of oil saturation is established. The difference between the initial oil saturation and the residual oil saturation can be used to quantitatively evaluate the water-flooded layers. The evaluation result of the water-flooded layers is combined with the ratio of the water-flooded wells in the marine sandstone reservoirs. As a result, the degree of water flooding in the marine sandstone reservoirs can be assessed. On the basis of structural characteristics and sedimentary environments, the horizontal and vertical water-flooding rules of the different types of reservoirs are elaborated upon, and the distribution rule of the remaining oil is disclosed. The remaining oil is mainly distributed in the high parts of the structure. The remaining oil exists in the top of the reservoirs with good physical properties while the thickness of the remaining oil ranges from 2-5 m. However, the thickness of the remaining oil of the reservoirs with poor physical properties ranges from 5-8 m. The high production of some of the drilled horizontal wells shows that the above distribution rule of the remaining oil is accurate. In the marine sandstone reservoirs of the M oilfield, the research on the well logging evaluation of the water-flooded layers and the distribution rule of the remaining oil has great practical significance to the prediction of the distribution of the remaining oil and the optimization of well locations.

Steam-soak performance in south Oman

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, S.A.

1991-11-01

With about 2 {times} 10{sup 9} stock-tank m{sup 3} (12.6 {times} 10{sup 9} STB) of medium/heavy oil originally in place (OOIP) in south Oman, considerable scope exists for increasing oil recovery by thermal methods. The viability of thermal recovery in south Oman was tested with a steamflood pilot in the Al Khlata sands of the Marmul field and a 2-year steam-soak project to test the applicability of steam soak in five south Oman oil fields producing heavy oil. This paper describes the performance of the latter project. The wells selected for the test program included a wide range of southmore » Oman reservoir and oil characteristics i.e., the main reservoir drive mechanisms of depletion, solution-gas, and edge- and bottomwater drive, the reservoir sandbody types, and oil viscosities from 80 to 4000 mPa {center dot} s (80 to 4,000 cp). Steam-soak operations were successful, and oil production accelerated significantly, with an average stimulate production rate twice that before stimulation. Acceleration was less marked in wells where reservoir energy is limited or where the primary (cold) water cut is more than 30%. At primary (cold) water cuts {gt}50%, no increase in oil production rate was observed. The process was simulated numerically for several wells, with the results in close agreement with performance. Improved understanding of the process resulting from the simulation allowed the most important factors influencing performance to be identified and aided process optimization in the field test. Two small-scale steam-soak projects currently are being assessed for implementatioimplementation in the early 1990's.« less

Hindcast, GIS and susceptibility modelling to assist oil spill clean-up and mitigation on the southern coast of Cyprus (Eastern Mediterranean)

NASA Astrophysics Data System (ADS)

Alves, Tiago M.; Kokinou, Eleni; Zodiatis, George; Lardner, Robin

2016-11-01

This study uses new oil-spill models, bathymetric, meteorological, oceanographic, geomorphological and geological data to assess the impact of distinct oil spill scenarios on the southern coast of Cyprus, Eastern Mediterranean. This approach results from the urgent need to predict oil spill dispersion after new oil terminals and depots were built at Vasilikos, southern coast of Cyprus. The terminals have been able to receive tankers with 500,000 deadweight tonnes from November 2014. The new geomorphological and geological data in this work show the shoreline of Cyprus to be of high susceptibility due to: (a) the presence of a narrow continental shelf capable of trapping large quantities of hydrocarbons; (b) the existence of uplifted wave-cut platforms, coastal lagoons and pools forming natural traps for oil, and (c) the presence of important tourist and Natura 2000 sites. Under particular weather and oceanographic conditions, oil spills offshore Larnaca Bay will quickly spread and reach the shoreline 46 h after the initial accident. Significantly, the models in this paper show a reduction from 84% to 19% in the volume of oil trapped on the coast if dispersants are applied, with the latter 19% being potentially kept at bay using booms and mechanical removal techniques. Based on these results, we suggest the early use of dispersants, booms and mechanical removal procedures to prevent the spreading of oil spilt in the broad area of Larnaca Bay.

Wastewater characterization survey, Victor Valley Wastewater Reclamation Authority and hazardous-waste survey at George AFB, California. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Binovi, R.D.; Ng, E.K.; Tetla, R.A.

1987-01-01

This is a report of a survey of the Victor Wastewater Reclamation Authority Sewerage system, the sewage treatment plant, and effluent from the various operations at George AFB, California. The scope of work included the characterization of the wastewater from George AFB, as well as characterization of effluents from 29 oil/water separators servicing industrial operations on base, flow measurements at three locations on base, a microbiological evaluation of aeration basin foam, bench-scale activated-sludge studies, and a review of results from previous surveys. Recommendations: (1) AFFF (Aqueous Film Forming Foam) should never be discharged to the sewer. (2) Programming for pretreatmentmore » should proceed at selected operations. (3) More waste and wastestream analysis be performed. (4) Upgrade waste accumulation points. (5) Implement an aggressive inspection program for oil/water separators. (6) Cut down on nonessential washing.« less

Publications - GMC 94 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Oil Company Clam Gulch 1-X well Authors: Makada, R. Publication Date: 1988 Publisher: Alaska Division , Vitrinite reflectance data of ditch cuttings from the Marathon Oil Company Clam Gulch 1-X well: Alaska

Publications - GMC 151 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Gulf Oil Corp. Point Mcintyre #1 well Authors: Unknown Publication Date: 1990 Publisher: Alaska reflectance data of cuttings (3,540-11,850) from the Gulf Oil Corp. Point Mcintyre #1 well: Alaska Division of

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phelps, J.; Hoopingarner, J.

Effective techniques have been developed from work on dozens of North Sea Wells to minimize the amount of oil-based mud discharged to the sea while maintaining acceptable levels of solids. Pressure to reduce pollution during the course of drilling prompted the development of these techniques. They involve personnel and optimization of mud system and procedures. Case histories demonstrate that regulations may be met with economical techniques using existing technology. The benefits of low solids content are widely known, and are a key part of any successful mud program. Good solids control should result in lower mud costs and better drillingmore » performance. Operators have specified high-performance shakers to accomplish this and have revised their mud programs with lower and lower allowable drilled solids percentages. This will pay off in certain areas. But with the U.K. Department of Energy regulations requiring cuttings oil discharge content (CODC) to be less than 150 g of oil/kg of dry solids discharge that went into effect Jan. 1, 1989, oil-loss control has a higher profile in the U.K. sector of the North Sea.« less

Sequential disinfection of E. coli O157:H7 on shredded lettuce leaves by aqueous chlorine dioxide, ozonated water, and thyme essential oil

NASA Astrophysics Data System (ADS)

Singh, Nepal; Singh, Rakesh K.; Bhunia, Arun K.; Stroshine, Richard L.; Simon, James E.

2001-03-01

There have been numerous studies on effectiveness of different sanitizers for microbial inactivation. However, results obtained from different studies indicate that microorganism cannot be easily removed from fresh cut vegetables because of puncture and cut surfaces with varying surface topographies. In this study, three step disinfection approach was evaluated for inactivation of E. coli O157:H7 on shredded lettuce leaves. Sequential application of thyme oil, ozonated water, and aqueous chlorine dioxide was evaluated in which thyme oil was applied first followed by ozonated water and aqueous chlorine dioxide. Shredded lettuce leaves inoculated with cocktail culture of E. coli O157:H7 (C7927, EDL 933 and 204 P), were washed with ozonated water (15 mg/l for 10min), aqueous chlorine dioxide (10 mg/l,for 10min) and thyme oil suspension (0.1%, v/v for 5min). Washing of lettuce leaves with ozonated water, chlorine dioxide and thyme oil suspension resulted in 0.44, 1.20, and 1.46 log reduction (log10 cfu/g), respectively. However, the sequential treatment achieved approximately 3.13 log reductions (log10 cfu/g). These results demonstrate the efficacy of sequential treatments in decontaminating shredded lettuce leaves containing E. coli O157:H7.

Impact of oil-based drill mud disposal on benthic foraminiferal assemblages on the continental margin off Angola

NASA Astrophysics Data System (ADS)

Jorissen, F. J.; Bicchi, E.; Duchemin, G.; Durrieu, J.; Galgani, F.; Cazes, L.; Gaultier, M.; Camps, R.

2009-12-01

In order to assess the possible environmental impact of oily cuttings discharged during oil exploration activities, we studied the benthic foraminiferal faunas in a five-station, 4-km-long sampling transect around a cuttings disposal site at about 670 m depth offshore Angola (W Africa), where drilling activities started 1.5 years before sampling. Living (Rose Bengal stained) and dead foraminiferal faunas were sampled in March 2006. The faunal patterns mirror the spatial distribution of hydrocarbons, which are dispersed into a southeastern direction. Four different areas can be distinguished on the basis of the investigated faunal parameters (density, diversity and species composition of the living fauna, and comparison with subrecent dead faunas). The fauna at station S31, 300 m SE of the oil cuttings disposal site, appears to be clearly impacted: the faunal density and diversity are maximal, but evenness is minimal. Taxa sensitive to organic enrichment, such as Uvigerina peregrina, Cancris auriculus and Cribrostomoides subglobosus, have largely disappeared, whereas the low-oxygen-resistant taxon Chilostomella oolina and opportunistic buliminids and bolivinids attain relatively high densities. At station S32, 500 m SE of the disposal site, environmental impact is still perceptible. The faunal density is slightly increased, and U. peregrina, apparently the most sensitive species, is still almost absent. The faunas found at 1 and 1.8 km SE of the disposal site are apparently no longer impacted by the drill mud disposal. Faunal density and diversity are low, and the faunal composition is typical for a mesotrophic to eutrophic upper slope environment. Finally, Station S35, 2 km NW of the disposal site, contains an intermediate fauna, where both the low-oxygen-resistant C. oolina and the more sensitive taxa ( U. peregrina, C. auriculus and C. subglobosus) are present. All taxa live close to the sediment-water interface here, indicating a reduced oxygen penetration into the sediment. Since the hydrocarbon concentration is low at this station, it appears that the faunal characteristics are the consequence of a slightly different environmental setting, and not due to a contamination with drill cuttings. Our data underline the large potential of benthic foraminifera as bio-indicators of anthropogenic enrichment in open marine settings, such as caused by the disposal of oily drill cuttings. The foraminiferal faunas react essentially by a density increase of a number of tolerant and/or opportunistic taxa, and a progressive disappearance of more sensitive taxa in the most impacted area. Rather surprisingly, large-sized taxa appear to be more sensitive than small-sized foraminiferal taxa.

On-line applications of numerical models in the Black Sea GIS

NASA Astrophysics Data System (ADS)

Zhuk, E.; Khaliulin, A.; Zodiatis, G.; Nikolaidis, A.; Nikolaidis, M.; Stylianou, Stavros

2017-09-01

The Black Sea Geographical Information System (GIS) is developed based on cutting edge information technologies, and provides automated data processing and visualization on-line. Mapserver is used as a mapping service; the data are stored in MySQL DBMS; PHP and Python modules are utilized for data access, processing, and exchange. New numerical models can be incorporated in the GIS environment as individual software modules, compiled for a server-based operational system, providing interaction with the GIS. A common interface allows setting the input parameters; then the model performs the calculation of the output data in specifically predefined files and format. The calculation results are then passed to the GIS for visualization. Initially, a test scenario of integration of a numerical model into the GIS was performed, using software, developed to describe a two-dimensional tsunami propagation in variable basin depth, based on a linear long surface wave model which is legitimate for more than 5 m depth. Furthermore, the well established oil spill and trajectory 3-D model MEDSLIK (http://www.oceanography.ucy.ac.cy/medslik/) was integrated into the GIS with more advanced GIS functionality and capabilities. MEDSLIK is able to forecast and hind cast the trajectories of oil pollution and floating objects, by using meteo-ocean data and the state of oil spill. The MEDSLIK module interface allows a user to enter all the necessary oil spill parameters, i.e. date and time, rate of spill or spill volume, forecasting time, coordinates, oil spill type, currents, wind, and waves, as well as the specification of the output parameters. The entered data are passed on to MEDSLIK; then the oil pollution characteristics are calculated for pre-defined time steps. The results of the forecast or hind cast are then visualized upon a map.

System for slicing wafers

NASA Technical Reports Server (NTRS)

1982-01-01

A newly patented process for slicing silicon wafers that has distinct advantages over methods now widely used is described. The primary advantage of the new system is that it allows the efficient slicing of a number of ingots simultaneously at high speed. The cutting action is performed mechanically, most often with diamond particles that are transported to the cutting zone by a fluid vehicle or have been made an integral part of the blade by plating or impregnation. The new system uses a multiple or ganged band saw, arranged and spaced so that each side, or length, segment of a blade element, or loop, provides a cutting function. Each blade is maintained precisely in position by guides as it enters and leaves each ingot. The cutting action is performed with a conventional abrasive slurry composed of diamond grit suspended in an oil- or water-based vehicle. The distribution system draws the slurry from the supply reservoir and pumps it to the injection tubes to supply it to each side of each ingot. A flush system is provided at the outer end of the work-station zone. In order to reduce potential damage, a pneumatically driven flushing fluid is provided.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Felson, B.; Ralaisomay, G.

The authors have encountered four cases of oil aspiration pneumonia complicated by carcinoma. Each had a clear-cut history of chronic intake of an oily substance, radiographic changes, and histologically documented oil aspiration pneumonia. Lung cancer later appeared in the involved area. A small number of similar cases also have been reported. The implication is that oil aspiration pneumonitis may induce bronchogenic carcinoma, particularly either the alveolar cell or the squamous cell variety. The radiographic diagnosis of the malignant transformation is difficult, and consequently the prognosis is poor.

Expansion of oil palm and other cash crops causes an increase of the land surface temperature in the Jambi province in Indonesia

NASA Astrophysics Data System (ADS)

Sabajo, Clifton R.; le Maire, Guerric; June, Tania; Meijide, Ana; Roupsard, Olivier; Knohl, Alexander

2017-10-01

Indonesia is currently one of the regions with the highest transformation rate of land surface worldwide related to the expansion of oil palm plantations and other cash crops replacing forests on large scales. Land cover changes, which modify land surface properties, have a direct effect on the land surface temperature (LST), a key driver for many ecological functions. Despite the large historic land transformation in Indonesia toward oil palm and other cash crops and governmental plans for future expansion, this is the first study so far to quantify the impacts of land transformation on the LST in Indonesia. We analyze LST from the thermal band of a Landsat image and produce a high-resolution surface temperature map (30 m) for the lowlands of the Jambi province in Sumatra (Indonesia), a region which suffered large land transformation towards oil palm and other cash crops over the past decades. The comparison of LST, albedo, normalized differenced vegetation index (NDVI) and evapotranspiration (ET) between seven different land cover types (forest, urban areas, clear-cut land, young and mature oil palm plantations, acacia and rubber plantations) shows that forests have lower surface temperatures than the other land cover types, indicating a local warming effect after forest conversion. LST differences were up to 10.1 ± 2.6 °C (mean ± SD) between forest and clear-cut land. The differences in surface temperatures are explained by an evaporative cooling effect, which offsets the albedo warming effect. Our analysis of the LST trend of the past 16 years based on MODIS data shows that the average daytime surface temperature in the Jambi province increased by 1.05 °C, which followed the trend of observed land cover changes and exceeded the effects of climate warming. This study provides evidence that the expansion of oil palm plantations and other cash crops leads to changes in biophysical variables, warming the land surface and thus enhancing the increase of the air temperature because of climate change.

Effect of lubricant environment on saw damage in silicon wafers

NASA Technical Reports Server (NTRS)

Kuan, T. S.; Shih, K. K.; Vanvechten, J. A.; Westdorp, W. A.

1982-01-01

The chemomechanical effect of lubricant environments on the inner diameter (ID) sawing induced surface damage in Si wafers was tested for four different lubricants: water, dielectric oil, and two commercial cutting solutions. The effects of applying different potential on Si crystals during the sawing were also tested. It is indicated that the number and depth of surface damage are sensitive to the chemical nature of the saw lubricant. It is determined that the lubricants that are good catalysts for breaking Si bonds can dampen the out of plane blade vibration more effectively and produce less surface damage. Correlations between the applied potential and the depth of damage in the dielectric oil and one of the commercial cutting solutions and possible mechanisms involved are discussed.

Rarefaction Shock Wave Cutter for Offshore Oil-Gas Platform Removal Final Report CRADA No. TC02009.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glenn, L. A.; Barker, J.

This was a collaborative effort between Lawrence Livermore National Security, LLC/Lawrence Livermore National Laboratory (LLNL) (formerly the University of California) and Jet Research Center, a wholly owned division of Halliburton Energy Services, Inc. to design and prototype an improved explosive cutter for cutting the support legs of offshore oil and gas platforms.

Measurement of H2S in Crude Oil and Crude Oil Headspace Using Multidimensional Gas Chromatography, Deans Switching and Sulfur-selective Detection

PubMed Central

Heshka, Nicole E.; Hager, Darcy B.

2015-01-01

A method for the analysis of dissolved hydrogen sulfide in crude oil samples is demonstrated using gas chromatography. In order to effectively eliminate interferences, a two dimensional column configuration is used, with a Deans switch employed to transfer hydrogen sulfide from the first to the second column (heart-cutting). Liquid crude samples are first separated on a dimethylpolysiloxane column, and light gases are heart-cut and further separated on a bonded porous layer open tubular (PLOT) column that is able to separate hydrogen sulfide from other light sulfur species. Hydrogen sulfide is then detected with a sulfur chemiluminescence detector, adding an additional layer of selectivity. Following separation and detection of hydrogen sulfide, the system is backflushed to remove the high-boiling hydrocarbons present in the crude samples and to preserve chromatographic integrity. Dissolved hydrogen sulfide has been quantified in liquid samples from 1.1 to 500 ppm, demonstrating wide applicability to a range of samples. The method has also been successfully applied for the analysis of gas samples from crude oil headspace and process gas bags, with measurement from 0.7 to 9,700 ppm hydrogen sulfide. PMID:26709594

[Study of cuttings identification using laser-induced breakdown spectroscopy].

PubMed

Tian, Ye; Wang, Zhen-nan; Hou, Hua-ming; Zhai, Xiao-wei; Ci, Xing-hua; Zheng, Rong-er

2012-08-01

Cutting identification is one of the most important links in the course of cutting logging which is very significant in the process of oil drilling. In the present paper, LIBS was used for identification of four kinds of cutting samples coming from logging field, and then multivariate analysis was used in data processing. The whole spectra model and the feature model were built for cuttings identification using PLS-DA method. The accuracy of the whole spectra model was 88.3%, a little more than the feature model with an accuracy of 86.7%. While in the aspect of data size, the variables were decreased from 24,041 to 27 by feature extraction, which increased the efficiency of data processing observably. The obtained results demonstrate that LIBS combined with chemometrics method could be developed as a rapid and valid approach to cutting identification and has great potential to be used in logging field.

Application of gas-fluid atomization technology in ultrosonic vibration cutting titanium alloy workpiece

NASA Astrophysics Data System (ADS)

Zhou, Zhimin; Zhang, Yuangliang; Li, Xiaoyan; Sun, Baoyuan

2009-11-01

To further improve machined surface quality of diamond cutting titanium workpiece and reduce diamond tool wear, it puts forward a kind of machining technology with mixture of carbon dioxide gas, water and vegetable oil atomized mist as cooling media in the paper. The cooling media is sprayed to cutting area through gas-liquid atomizer device to achieve purpose of cooling, lubricating, and protecting diamond tool. Experiments indicate that carbon dioxide gas can touch cutting surface more adequately through using gas-liquid atomization technology, which makes iron atoms of cutting surface cause a chemical reaction directly with carbon in carbon dioxide gas and reduce graphitizing degree of diamond tool. Thus, this technology of using gas-liquid atomization and ultrasonic vibration together for cutting Titanium Alloy is able to improve machined surface quality of workpiece and slow of diamond tool wear.

Isolation of genomic DNA from defatted oil seed residue of rapeseed (Brassica napus).

PubMed

Sadia, M; Rabbani, M A; Hameed, S; Pearce, S R; Malik, S A

2011-02-08

A simple protocol for obtaining pure, restrictable and amplifiable megabase genomic DNA from oil-free seed residue of Brassica napus, an important oil seed plant, has been developed. Oil from the dry seeds was completely recovered in an organic solvent and quantified gravimetrically followed by processing of the residual biomass (defatted seed residue) for genomic DNA isolation. The isolated DNA can be cut by a range of restriction enzymes. The method enables simultaneous isolation and recovery of lipids and genomic DNA from the same test sample, thus allowing two independent analyses from a single sample. Multiple micro-scale oil extraction from the commercial seeds gave approximately 39% oil, which is close to the usual oil recovery from standard oil seed. Most of the amplified fragments were scored in the range of 2.5 to 0.5 kb, best suited for scoring as molecular diagnostics.

The formation process and responsive impacts of single oil droplet in submerged process.

PubMed

Li, Haoshuai; Meng, Long; Shen, Tiantian; Zhang, Jianrui; Bao, Mutai; Sun, Peiyan

2017-11-15

Simulated column was applied to research forming progress of single oil droplet in submerged process, floating progress, and study effects of environment factors and dispersants on the concentration of oil hydrocarbon in water as well as changing rules of oil droplet sizes. As expected, particular formation mechanism of single oil droplet was presented. When necking down length L is 0.5 time of oil droplet diameter (d) after expansion phase, necking down becomes long and thin; when L=2d, necking down begins to break. In floating progress, the shape changes oval and its motion trail becomes an auger-type. Fluctuation occurs at horizontal direction. Dispersants decrease oil droplet size by its dispersion effect, and cut down effect of Van Der Waals force among oil droplets. More broadly, these findings provide rare empirical evidence expounding formation mechanism of single oil droplet to increasing ability of oil spill response. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical water shutoff profile research status and development trends

NASA Astrophysics Data System (ADS)

Xu, L. T.

2017-08-01

Excess water production is now a common problem encountered in almost every water flooding mature oilfield. The exploitation of oil field is faced with great challenge because of the decrease of oil field production. For the development of high water cut rare the status quo chemical water shutoff profile control technology is an important solution to solve this problem. Oilfield chemical water shutoff has important application prospects. This paper analyzes the water shutoff profile control and water shutoff profile control agent currently oilfield applications, moreover the use and development of blocking agent profile technology is to improve reservoir recovery and propose solutions. With the constant increase in water cut, profile technology should be simple, efficient, practical and profile control agent of development should be economic, environmental, and long period

Analyze and Study Ionospheric Scintillation and Total Electron Content Variability (Ionospheric Studies and TEC Variations).

DTIC Science & Technology

1981-03-01

gradient of iii/a ion. SniAtt polari/ji oil fields As mentioned earlier, our object is to use the same valuse if L"~ as (Es Bi, H2 termnal I ire sut...spectral cut- arranged in order of decreasing wet longitude of ionospheric inter- %ection points of the various ray path% as shown in Figure I. oil in the...1977). Review of equatorial have suggested that density enhancements may scintillation phenomena in the light of recent developments spread oil over a

Effects of clove essential oil and eugenol on quality and browning control of fresh-cut lettuce.

PubMed

Chen, Xiangning; Ren, Lupei; Li, Menglin; Qian, Jia; Fan, Junfeng; Du, Bin

2017-01-01

This study confirmed the inhibitory effects of clove essential oil (CEO) and eugenol (EUG) on the browning and relevant enzymes of fresh-cut lettuce, and examined associated mechanisms by inhibition kinetics and computational docking analysis. Fresh-cut lettuce was treated with 0.05% CEO and 0.05% EUG solutions, resulting in inhibition of the deterioration of texture quality and browning of the lettuce surface and interior. Compared with the controls, CEO and EUG significantly inhibited the activities of phenylalanine ammonia lyase (PAL), polyphenol oxidase (PPO), and peroxidase (POD, all p<0.05). EUG suppressed PAL, PPO, and POD in vitro in a dose-dependent manner, with IC50 values of 5.4±0.9, 29.5±3.5, and 61.9±6.7mM, respectively. The binding and inhibition effects of EUG on PAL, PPO, and POD, determined by inhibition kinetics and computational docking analysis, established EUG as a competitive inhibitor of these browning-relevant enzymes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Canopy volume removal from oil and gas development activity in the upper Susquehanna River basin in Pennsylvania and New York (USA): An assessment using lidar data

USGS Publications Warehouse

Young, John A.; Maloney, Kelly O.; Slonecker, Terry; Milheim, Lesley E.; Siripoonsup, David

2018-01-01

Oil and gas development is changing the landscape in many regions of the United States and globally. However, the nature, extent, and magnitude of landscape change and development, and precisely how this development compares to other ongoing land conversion (e.g. urban/sub-urban development, timber harvest) is not well understood. In this study, we examine land conversion from oil and gas infrastructure development in the upper Susquehanna River basin in Pennsylvania and New York, an area that has experienced much oil and gas development over the past 10 years. We quantified land conversion in terms of forest canopy geometric volume loss in contrast to previous studies that considered only areal impacts. For the first time in a study of this type, we use fine-scale lidar forest canopy geometric models to assess the volumetric change due to forest clearing from oil and gas development and contrast this land change to clear cut forest harvesting, and urban and suburban development. Results show that oil and gas infrastructure development removed a large volume of forest canopy from 2006 to 2013, and this removal spread over a large portion of the study area. Timber operations (clear cutting) on Pennsylvania State Forest lands removed a larger total volume of forest canopy during the same time period, but this canopy removal was concentrated in a smaller area. Results of our study point to the need to consider volumetric impacts of oil and gas development on ecosystems, and to place potential impacts in context with other ongoing land conversions.

40 CFR 435.41 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., safety showers, eye-wash stations, hand-wash stations, fish cleaning stations, and galleys located within... formation oil carried out from the wellbore with the drilling fluid. (2) Dry drill cuttings means the...

Refinery Integration of By-Products from Coal-Derived Jet Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song

2006-05-17

This report summarizes the accomplishments toward project goals during the first six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. Characterization of the gasolinemore » fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of fuel oil indicates that the fuel is somewhere in between a No. 4 and a No. 6 fuel oil. Emission testing indicates the fuel burns similarly to these two fuels, but trace metals for the coal-based material are different than petroleum-based fuel oils. Co-coking studies using cleaned coal are highly reproducible in the pilot-scale delayed coker. Evaluation of the coke by Alcoa, Inc. indicated that while the coke produced is of very good quality, the metals content of the carbon is still high in iron and silica. Coke is being evaluated for other possible uses. Methods to reduce metal content are being evaluated.« less

Study on the Effect of Diamond Grain Size on Wear of Polycrystalline Diamond Compact Cutter

NASA Astrophysics Data System (ADS)

Abdul-Rani, A. M.; Che Sidid, Adib Akmal Bin; Adzis, Azri Hamim Ab

2018-03-01

Drilling operation is one of the most crucial step in oil and gas industry as it proves the availability of oil and gas under the ground. Polycrystalline Diamond Compact (PDC) bit is a type of bit which is gaining popularity due to its high Rate of Penetration (ROP). However, PDC bit can easily wear off especially when drilling hard rock. The purpose of this study is to identify the relationship between the grain sizes of the diamond and wear rate of the PDC cutter using simulation-based study with FEA software (ABAQUS). The wear rates of a PDC cutter with a different diamond grain sizes were calculated from simulated cuttings of cutters against granite. The result of this study shows that the smaller the diamond grain size, the higher the wear resistivity of PDC cutter.

Design of a new abrasive slurry jet generator

NASA Astrophysics Data System (ADS)

Wang, F. C.; Shi, L. L.; Guo, C. W.

2017-12-01

With the advantages of a low system working pressure, good jet convergence and high cutting quality, abrasive slurry jet (ASJ) has broad application prospects in material cutting and equipment cleaning. Considering that the generator plays a crucial role in ASJ system, the paper designed a new type ASJ generator using an electric oil pump, a separate plunger cylinder, and a spring energized seal. According to the determining of structure shape, size and seal type, a new ASJ generator has been manufactured out and tested by a series of experiments. The new generator separates the abrasive slurry from the dynamic hydraulic oil, which can improve the service life of the ASJ system. And the new ASJ system can reach 40 MPa and has good performance in jet convergence, which deserves to popularization and application in materials machining.

Fischer Assays of Oil-Shale Drill Cores and Rotary Cuttings from the Greater Green River Basin, Southwestern Wyoming

USGS Publications Warehouse

,

2008-01-01

Chapter 1 of this CD-ROM is a database of digitized Fischer (shale-oil) assays of cores and cuttings from boreholes drilled in the Eocene Green River oil shale deposits in southwestern Wyoming. Assays of samples from some surface sections are also included. Most of the Fischer assay analyses were made by the former U.S. Bureau of Mines (USBM) at its laboratory in Laramie, Wyoming. Other assays, made by institutional or private laboratories, were donated to the U.S. Geological Survey (USGS) and are included in this database as well as Adobe PDF-scanned images of some of the original laboratory assay reports and lithologic logs prepared by USBM geologists. The size of this database is 75.2 megabytes and includes information on 971 core holes and rotary-drilled boreholes and numerous surface sections. Most of these data were released previously by the USBM and the USGS through the National Technical Information Service but are no longer available from that agency. Fischer assays for boreholes in northeastern Utah and northwestern Colorado have been published by the USGS. Additional data include geophysical logs, groundwater data, chemical and X-ray diffraction analyses, and other data. These materials are available for inspection in the office of the USGS Central Energy Resources Team in Lakewood, Colorado. The digitized assays were checked with the original laboratory reports, but some errors likely remain. Other information, such as locations and elevations of core holes and oil and gas tests, were not thoroughly checked. However, owing to the current interest in oil-shale development, it was considered in the public interest to make this preliminary database available at this time. Chapter 2 of this CD-ROM presents oil-yield histograms of samples of cores and cuttings from exploration drill holes in the Eocene Green River Formation in the Great Divide, Green River, and Washakie Basins of southwestern Wyoming. A database was compiled that includes about 47,000 Fischer assays from 186 core holes and 240 rotary drill holes. Most of the oil yield data are from analyses performed by the former U.S. Bureau of Mines oil shale laboratory in Laramie, Wyoming, with some analyses made by private laboratories. Location data for 971 Wyoming oil-shale drill holes are listed in a spreadsheet that is included in the CD-ROM. These Wyoming Fischer assays and histograms are part of a much larger collection of oil-shale information, including geophysical and lithologic logs, water data, chemical and X-ray diffraction analyses on the Green River oil-shale deposits in Colorado, Utah, and Wyoming held by the U.S. Geological Survey. Because of an increased interest in oil shale, this CD-ROM containing Fischer assay data and oil-yield histograms for the Green River oil-shale deposits in southwestern Wyoming is being released to the public. Microsoft Excel spreadsheets included with Chapter 2 contain the Fischer assay data from the 426 holes and data on the company name and drill-hole name, and location. Histograms of the oil yields obtained from the Fischer assays are presented in both Grapher and PDF format. Fischer assay text data files are also included in the CD-ROM.

A complex carotenoid palette tunes avian color vision.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Timlin, Jerilyn A.; Toomey, Matthew B.; Collins, Aaron M.

The brilliantly coloured cone oil droplets of the avian retina function as long-pass cut-off filters that tune the spectral sensitivity of the photoreceptors and are hypothesized to enhance colour discrimination and improve colour constancy. Although it has long been known that these droplets are pigmented with carotenoids, their precise composition has remained uncertain owing to the technical challenges of measuring these very small, dense and highly refractile optical organelles. In this study, we integrated results from high-performance liquid chromatography, hyperspectral microscopy and microspectrophotometry to obtain a comprehensive understanding of oil droplet carotenoid pigmentation in the chicken ( Gallus gallus). Wemore » find that each of the four carotenoid-containing droplet types consists of a complex mixture of carotenoids, with a single predominant carotenoid determining the wavelength of the spectral filtering cut-off. Consistent with previous reports, we find that the predominant carotenoid type in the oil droplets of long-wavelength-sensitive, medium-wavelength-sensitive and short-wavelength-sensitive type 2 cones are astaxanthin, zeaxanthin and galloxanthin, respectively. In addition, the oil droplet of the principal member of the double cone contains a mixture of galloxanthin and two hydroxycarotenoids (lutein and zeaxanthin). Short-wavelength-absorbing apocarotenoids are present in all of the droplet types, providing filtering of light in a region of the spectrum where filtering by hydroxy- and ketocarotenoids may be incomplete. Furthermore, birds rely on a complex palette of carotenoid pigments within their cone oil droplets to achieve finely tuned spectral filtering.« less

A complex carotenoid palette tunes avian color vision.

DOE PAGES

Timlin, Jerilyn A.; Toomey, Matthew B.; Collins, Aaron M.; ...

2015-10-07

The brilliantly coloured cone oil droplets of the avian retina function as long-pass cut-off filters that tune the spectral sensitivity of the photoreceptors and are hypothesized to enhance colour discrimination and improve colour constancy. Although it has long been known that these droplets are pigmented with carotenoids, their precise composition has remained uncertain owing to the technical challenges of measuring these very small, dense and highly refractile optical organelles. In this study, we integrated results from high-performance liquid chromatography, hyperspectral microscopy and microspectrophotometry to obtain a comprehensive understanding of oil droplet carotenoid pigmentation in the chicken ( Gallus gallus). Wemore » find that each of the four carotenoid-containing droplet types consists of a complex mixture of carotenoids, with a single predominant carotenoid determining the wavelength of the spectral filtering cut-off. Consistent with previous reports, we find that the predominant carotenoid type in the oil droplets of long-wavelength-sensitive, medium-wavelength-sensitive and short-wavelength-sensitive type 2 cones are astaxanthin, zeaxanthin and galloxanthin, respectively. In addition, the oil droplet of the principal member of the double cone contains a mixture of galloxanthin and two hydroxycarotenoids (lutein and zeaxanthin). Short-wavelength-absorbing apocarotenoids are present in all of the droplet types, providing filtering of light in a region of the spectrum where filtering by hydroxy- and ketocarotenoids may be incomplete. Furthermore, birds rely on a complex palette of carotenoid pigments within their cone oil droplets to achieve finely tuned spectral filtering.« less

Influence of stability of polymer surfactant on oil displacement mechanism

NASA Astrophysics Data System (ADS)

Liu, Li; Li, Chengliang; Pi, Yanming; Wu, Di; He, Ying; Geng, Liang

2018-02-01

At present, most of the oilfields of China have entered the late stage of high water-cut development, and three oil recovery technique has become the leading technology for improving oil recovery. With the improvement of three oil recovery techniques, the polymer surfactant flooding technology has been widely promoted in oil fields in recent years. But in the actual field experiment, it has been found that the polymer surfactant has chromatographic separation at the extraction end, which indicates that the property of the polymer surfactant has changed during the displacement process. At present, there was few literature about how the stability of polymer surfactant affects the oil displacement mechanism. This paper used HuaDing-I polymer surfactant to conduct a micro photolithography glass flooding experiment, and then compared the oil displacement law of polymer surfactant before and after static setting. Finally, the influence law of stability of polymer surfactant on the oil displacement mechanism is obtained by comprehensive analysis.

Including impacts of particulate emissions on marine ecosystems in life cycle assessment: the case of offshore oil and gas production.

PubMed

Veltman, Karin; Huijbregts, Mark A J; Rye, Henrik; Hertwich, Edgar G

2011-10-01

Life cycle assessment is increasingly used to assess the environmental performance of fossil energy systems. Two of the dominant emissions of offshore oil and gas production to the marine environment are the discharge of produced water and drilling waste. Although environmental impacts of produced water are predominantly due to chemical stressors, a major concern regarding drilling waste discharge is the potential physical impact due to particles. At present, impact indicators for particulate emissions are not yet available in life cycle assessment. Here, we develop characterization factors for 2 distinct impacts of particulate emissions: an increased turbidity zone in the water column and physical burial of benthic communities. The characterization factor for turbidity is developed analogous to characterization factors for toxic impacts, and ranges from 1.4 PAF (potentially affected fraction) · m(3) /d/kg(p) (kilogram particulate) to 7.0 x 10³ [corrected] for drilling mud particles discharged from the rig. The characterization factor for burial describes the volume of sediment that is impacted by particle deposition on the seafloor and equals 2.0 × 10(-1) PAF · m(3) /d/kg(p) for cutting particles. This characterization factor is quantified on the basis of initial deposition layer characteristics, such as height and surface area, the initial benthic response, and the recovery rate. We assessed the relevance of including particulate emissions in an impact assessment of offshore oil and gas production. Accordingly, the total impact on the water column and on the sediment was quantified based on emission data of produced water and drilling waste for all oil and gas fields on the Norwegian continental shelf in 2008. Our results show that cutting particles contribute substantially to the total impact of offshore oil and gas production on marine sediments, with a relative contribution of 55% and 31% on the regional and global scale, respectively. In contrast, the contribution of particulate emissions to the total impact on the marine water column is of minor importance. We conclude that particles are an important stressor in marine ecosystems, particularly for marine sediment, and particulate emissions should therefore be included in a (life cycle) impact assessment of offshore oil and gas production. Copyright © 2011 SETAC.

Design and numerical simulation on an auto-cumulative flowmeter in horizontal oil-water two-phase flow

NASA Astrophysics Data System (ADS)

Xie, Beibei; Kong, Lingfu; Kong, Deming; Kong, Weihang; Li, Lei; Liu, Xingbin; Chen, Jiliang

2017-11-01

In order to accurately measure the flow rate under the low yield horizontal well conditions, an auto-cumulative flowmeter (ACF) was proposed. Using the proposed flowmeter, the oil flow rate in horizontal oil-water two-phase segregated flow can be finely extracted. The computational fluid dynamics software Fluent was used to simulate the fluid of the ACF in oil-water two-phase flow. In order to calibrate the simulation measurement of the ACF, a novel oil flow rate measurement method was further proposed. The models of the ACF were simulated to obtain and calibrate the oil flow rate under different total flow rates and oil cuts. Using the finite-element method, the structure of the seven conductance probes in the ACF was simulated. The response values for the probes of the ACF under the conditions of oil-water segregated flow were obtained. The experiments for oil-water segregated flow under different heights of the oil accumulation in horizontal oil-water two-phase flow were carried out to calibrate the ACF. The validity of the oil flow rate measurement in horizontal oil-water two-phase flow was verified by simulation and experimental results.

Design and numerical simulation on an auto-cumulative flowmeter in horizontal oil-water two-phase flow.

PubMed

Xie, Beibei; Kong, Lingfu; Kong, Deming; Kong, Weihang; Li, Lei; Liu, Xingbin; Chen, Jiliang

2017-11-01

In order to accurately measure the flow rate under the low yield horizontal well conditions, an auto-cumulative flowmeter (ACF) was proposed. Using the proposed flowmeter, the oil flow rate in horizontal oil-water two-phase segregated flow can be finely extracted. The computational fluid dynamics software Fluent was used to simulate the fluid of the ACF in oil-water two-phase flow. In order to calibrate the simulation measurement of the ACF, a novel oil flow rate measurement method was further proposed. The models of the ACF were simulated to obtain and calibrate the oil flow rate under different total flow rates and oil cuts. Using the finite-element method, the structure of the seven conductance probes in the ACF was simulated. The response values for the probes of the ACF under the conditions of oil-water segregated flow were obtained. The experiments for oil-water segregated flow under different heights of the oil accumulation in horizontal oil-water two-phase flow were carried out to calibrate the ACF. The validity of the oil flow rate measurement in horizontal oil-water two-phase flow was verified by simulation and experimental results.

Publications - GMC 253 | Alaska Division of Geological & Geophysical

Science.gov Websites

of the following Copper River basin oil and gas exploratory wells: Amoco Production Company Ahtna Inc Reference Unknown, 1995, Source rock geochemical and visual kerogen data from cuttings of the following

Separations and characterizations of fractions from Mayan, Heavy Arabian, and Hondo crude oils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kircher, C.C.

1989-04-01

The results from hydrotreating the atmospheric residua of Hondo, Heavy Arabian, and Mayan crude oils have been reported recently. Over the same fixed-bed catalyst, the hydrosulfurization activities varied by a factor of two and the hydrodemetallation activities varied almost four-fold. Correlations among the relative activities and the elemental compositions of the feed oils showed a direct relationship between the hydrodemetallation activity and the metals content of the petroleum resins fractions, hereafter called polars. Thus, to discover chemical differences in feed oils and polars that may affect a catalysts activity, they have developed separation schemes to separate the oils into theirmore » component fractions and used various analytical techniques to characterize the fractions. The separation scheme developed is a modification and extension of the ASTM D2007 procedure. The sample is separated into saturates, aromatics, polars, and asphaltenes by precipitation/filtration and chromatography with Attapulgus cla and silica gel; then the polars are separated into various acids, bases, and neutral polars with macroporous ion exchange resins. This separation scheme has been applied to 650{degree}F + cut from Hondo (offshore California) crude. The fractions were characterized with carbon and hydrogen elemental analysis, XRF spectrometry for nickel, vanadium, and sulfur, chemiluminescence spectrometry for nitrogen. GC simulated distillations (saturates only), vapor pressure osmetry (number-average molecular weight) in toluene, flame emission spectrometry, and {sup 13}C-NMR spectroscopy.« less

Yield and Water Productivity Responses to Irrigation Cut-off Strategies after Fruit Set Using Stem Water Potential Thresholds in a Super-High Density Olive Orchard

PubMed Central

Ahumada-Orellana, Luis E.; Ortega-Farías, Samuel; Searles, Peter S.; Retamales, Jorge B.

2017-01-01

An increase in the land area dedicated to super-high density olive orchards has occurred in Chile in recent years. Such modern orchards have high irrigation requirements, and optimizing water use is a priority. Moreover, this region presents low water availability, which makes necessary to establish irrigation strategies to improve water productivity. An experiment was conducted during four consecutive growing seasons (2010–2011 to 2013–2014) to evaluate the responses of yield and water productivity to irrigation cut-off strategies. These strategies were applied after fruit set using midday stem water potential (Ψstem) thresholds in a super-high density olive orchard (cv. Arbequina), located in the Pencahue Valley, Maule Region, Chile. The experimental design was completely randomized with four irrigation cut-off treatments based on the Ψstem thresholds and four replicate plots per treatment (five trees per plot). Similar to commercial growing conditions in our region, the Ψstem in the T1 treatment was maintained between -1.4 and -2.2 MPa (100% of actual evapotranspiration), while T2, T3 and T4 treatments did not receive irrigation from fruit set until they reached a Ψstem threshold of approximately -3.5, -5.0, and -6.0 MPa, respectively. Once the specific thresholds were reached, irrigation was restored and maintained as T1 in all treatments until fruits were harvested. Yield and its components were not significantly different between T1 and T2, but fruit yield and total oil yield, fruit weight, and fruit diameter were decreased by the T3 and T4 treatments. Moreover, yield showed a linear response with water stress integral (SΨ), which was strongly influenced by fruit load. Total oil content (%) and pulp/stone ratio were not affected by the different irrigation strategies. Also, fruit and oil water productivities were significantly greater in T1 and T2 than in the T3 and T4. Moreover, the T2, T3, and T4 treatments averaged 37, 51, and 72 days without irrigation which represented 75–83, 62–76, and 56–70% of applied water compared with T1, respectively. These results suggest that using the T2 irrigation cut-off strategy could be applied in a super-high density olive orchard (cv. Arbequina) because it maintained yields, saving 20% of the applied water. PMID:28785274

U.S. oil dependence 2014: Is energy independence in sight?

DOE PAGES

Greene, David L.; Liu, Changzheng

2015-06-10

The importance of reducing U.S. oil dependence may have changed in light of developments in the world oil market over the past two decades. Since 2005, increased domestic production and decreased oil use have cut U.S. import dependence in half. The direct costs of oil dependence to the U.S. economy are estimated under four U.S. Energy Information Administration Scenarios to 2040. The key premises of the analysis are that the primary oil market failure is the use of market power by OPEC and that U.S. economic vulnerability is a result of the quantity of oil consumed, the lack of readilymore » available, economical substitutes and the quantity of oil imported. Monte Carlo simulations of future oil market conditions indicate that the costs of U.S. oil dependence are likely to increase in constant dollars but decrease relative to U.S. gross domestic product unless oil resources are larger than estimated by the U.S. Energy Information Administration. In conclusion, reducing oil dependence therefore remains a valuable goal for U.S. energy policy and an important co-benefit of mitigating greenhouse gas emissions.« less

Hot, deep origin of petroleum: deep basin evidence and application

USGS Publications Warehouse

Price, Leigh C.

1978-01-01

Use of the model of a hot deep origin of oil places rigid constraints on the migration and entrapment of crude oil. Specifically, oil originating from depth migrates vertically up faults and is emplaced in traps at shallower depths. Review of petroleum-producing basins worldwide shows oil occurrence in these basins conforms to the restraints of and therefore supports the hypothesis. Most of the world's oil is found in the very deepest sedimentary basins, and production over or adjacent to the deep basin is cut by or directly updip from faults dipping into the basin deep. Generally the greater the fault throw the greater the reserves. Fault-block highs next to deep sedimentary troughs are the best target areas by the present concept. Traps along major basin-forming faults are quite prospective. The structural style of a basin governs the distribution, types, and amounts of hydrocarbons expected and hence the exploration strategy. Production in delta depocenters (Niger) is in structures cut by or updip from major growth faults, and structures not associated with such faults are barren. Production in block fault basins is on horsts next to deep sedimentary troughs (Sirte, North Sea). In basins whose sediment thickness, structure and geologic history are known to a moderate degree, the main oil occurrences can be specifically predicted by analysis of fault systems and possible hydrocarbon migration routes. Use of the concept permits the identification of significant targets which have either been downgraded or ignored in the past, such as production in or just updip from thrust belts, stratigraphic traps over the deep basin associated with major faulting, production over the basin deep, and regional stratigraphic trapping updip from established production along major fault zones.

Silicone Oil Swelling Slippery Surfaces Based on Mussel-Inspired Magnetic Nanoparticles with Multiple Self-Healing Mechanisms.

PubMed

Jin, Biyu; Liu, Mingzhu; Zhang, Qinghua; Zhan, Xiaoli; Chen, Fengqiu

2017-10-03

In this work, a novel substrate building block, magnetic Fe 3 O 4 nanoparticles armed with dopamine molecules were developed via mussel-inspired metal-coordination bonds. Combined with glycidyl methacrylate, polydimethylsiloxane propyl ether methacrylate, and diethylenetriamine, the original silicone oil swelling slippery liquid-infused porous surfaces (SLIPS) were first prepared by reversible coordinate bonds and strong covalent bonds cross-linking process. The matrix mechanical characteristics and surface physicochemical properties were systematically investigated. Results showed that the mechanical property of copolymer matrix and surface wettability of SLIPS can be remarkably recovered, which were due to the synergistic interactions of magnetic nanoparticles' intrinsic photothermal effect, reversible Fe-catechol coordination, and diffused lubricating liquid. After irradiating with sunlamp for 2 h and sequentially healing for 10 h under ambient conditions, the crack almost disappeared under optical microscopy with 78.25% healing efficiency (HEf) of toughness, and surface slippery was completely retrieved to water droplets. The efficient self-heal of copolymer matrix (66.5% HEf after eighth cutting-healing cycle) and recovering of slipperiness (SA < 5° and 5° < SA < 17° after fourth and eighth cutting-centrifuging-healing cycles, respectively) would extend longevity of SLIPS when subjected to multiple damages. Moreover, the prepared SLIPS displayed superb self-cleaning and liquid-repellent properties to a wide range of particulate contaminants and fluids.

62. VIEW LOOKING NORTHWEST AT THE OIL FILLED CIRCUIT BREAKER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

62. VIEW LOOKING NORTHWEST AT THE OIL FILLED CIRCUIT BREAKER FOR GENERATOR NUMBER 1. CIRCUIT BREAKERS ARE AUTOMATED SWITCHES WHICH DISCONNECT THE GENERATORS FROM THE LINE WHEN SHORT CIRCUITS OCCUR. WHEN CIRCUITS INVOLVING HIGH CURRENTS AND VOLTAGES ARE BROKEN, THE AIR SURROUNDING MECHANICAL PARTS OF THE SWITCH BECOMES IONIZED AND CONTINUES TO CONDUCT ELECTRIC POWER ACROSS ANY GAP IN THE SWITCH CONTACTS. TO PREVENT THIS AND INSURE A POSITIVE INTERRUPTION OF CURRENT, THE SWITCH CONTACTS ARE IMMERSED IN A CONTAINER OF OIL. THE OIL DOES NOT SUPPORT THE FORMATION OF AN ARC AND EFFECTIVELY CUTS OFF THE CURRENT WHEN THE SWITCH CONTACTS ARE OPENED. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbett, R.A

Another quality crude oil is available from the North Sea. Norway's Oseberg crude oil entered the export market on Dec. 1, 1988. This premium, low-sulfur crude oil is currently being produced at approximately 240,000 b/d from the Norwegian sector of the North Sea. Two platforms, operated by Den Norske Stats Oijeselskap A.S. (Statoil), are currently in production, with a third scheduled to go into production in 1991. Oseberg is a typical, low-sulfur North Sea crude oil that will provide a full range of high-quality, low-sulfur products. The naphtha cuts are of intermediate to paraffinic quality, making them suitable for gasolinemore » production. The Oseberg crude is stabilized at the offshore platform and then transported to the Sture terminal, north of Bergen, Norway. The terminal can handle crude oil tankers up to 300,000 DWT.« less

Oil markets in turmoil: an economic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verleger, P.K. Jr.

1982-01-01

Departing from conventional wisdom about the forces most responsible for oil price increases, this book analyzes the response of consumers, oil companies, and oil-exporting nations to show that lethargy, not greed, best describes the behavior of these participants during a supply disruption. The adjustment to changes in market conditions is so slow that minor incidents are transformed into major crises. Assessing existing policy options, Verleger dispels the idea of matching supply losses with an equal cut in consumption. He recommends a free-market approach, which entails raising prices quickly, imposing large tariffs on imports, encouraging the development of private stockpiles, andmore » using spot prices as an indicator of oil shortages. He shows that the market approach will impose fewer costs than the regulatory approach in the long run. 83 references, 17 figures, 70 tables.« less

Metal drilling with portable hand drills

NASA Technical Reports Server (NTRS)

Edmiston, W. B.; Harrison, H. W.; Morris, H. E.

1970-01-01

Study of metal drilling solves problems of excessive burring, oversized holes, and out-of-round holes. Recommendations deal with using the proper chemical coolants, applying the coolants effectively, employing cutting oils, and dissipating the heat caused by drilling.

Health hazard evaluation report HETA 85-039-1723, E. L. Smithe Machine Company, Duncansville, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, D.E.

1986-08-01

The International Association of Machinists Local 2348 requested an investigation of reported skin rashes and headaches associated with cutting and cooling oils and solvents used in the machine shop. Of 62 employees interviewed, 42 had experienced skin problems occurring on their hands and arms including red skin, dry skin, cracked skin, or itchy skin, related to chemical exposures at the workplace. Xerosis, lichenification, or eczema of the hands and arms were noted on examination of 17 employees of the Lathe Department and 18 of those from the Milling Department. Respiratory and neurological complaints were also found among these employees. Themore » author concluded that the incidence of hand and arm xerosis and eczema in workers in the machining area may be associated with exposure to cutting oils. The author recommends that changes be made to minimize skin exposure and provide adequate ventilation and humidification.« less

Environment-friendly drilling operation technology

NASA Astrophysics Data System (ADS)

Luo, Huaidong; Jing, Ning; Zhang, Yanna; Huang, Hongjun; Wei, Jun

2017-01-01

Under the circumstance that international safety and environmental standards being more and more stringent, drilling engineering is facing unprecedented challenges, the extensive traditional process flow is no longer accepted, the new safe and environment-friendly process is more suitable to the healthy development of the industry. In 2015, CNPCIC adopted environment-friendly drilling technology for the first time in the Chad region, ensured the safety of well control, at the same time increased the environmental protection measure, reduced the risk of environmental pollution what obtain the ratification from local government. This technology carries out recovery and disposal of crude oil, cuttings and mud without falling on the ground. The final products are used in road and well site construction, which realizes the reutilization of drilling waste, reduces the operating cost, and provides a strong technical support for cost-cutting and performance-increase of drilling engineering under low oil price.

Foreskin cutting beliefs and practices and the acceptability of male circumcision for HIV prevention in Papua New Guinea

PubMed Central

2013-01-01

Background Male circumcision (MC) reduces HIV acquisition and is a key public health intervention in settings with high HIV prevalence, heterosexual transmission and low MC rates. In Papua New Guinea (PNG), where HIV prevalence is 0.8%, there is no medical MC program for HIV prevention. There are however many different foreskin cutting practices across the country’s 800 language groups. The major form exposes the glans but does not remove the foreskin. This study aimed to describe and quantify foreskin cutting styles, practices and beliefs. It also aimed to assess the acceptability of MC for HIV prevention in PNG. Methods Cross-sectional multicentre study, at two university campuses (Madang Province and National Capital District) and at two ‘rural development’ sites (mining site Enga Province; palm-oil plantation in Oro Province). Structured questionnaires were completed by participants originating from all regions of PNG who were resident at each site for study or work. Results Questionnaires were completed by 861 men and 519 women. Of men, 47% reported a longitudinal foreskin cut (cut through the dorsal surface to expose the glans but foreskin not removed); 43% reported no foreskin cut; and 10% a circumferential foreskin cut (complete removal). Frequency and type of cut varied significantly by region of origin (p < .001). Most men (72-82%) were cut between the ages of 10 – 20 years. Longitudinal cuts were most often done in a village by a friend, with circumferential cuts most often done in a clinic by a health professional. Most uncut men (71%) and longitudinal cut men (84%) stated they would remove their foreskin if it reduced the risk of HIV infection. More than 95% of uncut men and 97% of longitudinal cut men would prefer the procedure in a clinic or hospital. Most men (90%) and women (74%) stated they would remove the foreskin of their son if it reduced the risk of HIV infection. Conclusion Although 57% of men reported some form of foreskin cut only 10% reported the complete removal of the foreskin, the procedure on which international HIV prevention strategies are based. The acceptability of MC (complete foreskin removal) is high among men (for themselves and their sons) and women (for their sons). Potential MC services need to be responsive to the diversity of beliefs and practices and consider health system constraints. A concerted research effort to investigate the potential protective effects of longitudinal cuts for HIV acquisition is essential given the scale of longitudinal cuts in PNG. PMID:24015786

The potentiation of the antimicrobial activities of cutting fluid preservatives by EDTA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Izzat, I.N.; Bennett, E.O.

1978-01-01

The potentiation of the antimicrobial activities of cutting fluid preservatives by EDTA was confirmed in experiments in which 500 ppm of the disodium salt of EDTA was used in combination with 12 different metalworking fluids containing 500 ppm of o-phenylphenol, tris(hydroxymethyl) nitromethane, hexahydro- 1,3,5-tris(2-hydroxyethyl)-s-triazine alone or complexed with iodine, hexahydro- 1,3,5-triethyl-s-triazine, 1-(3-chloroallyl)- 3,5,7-triaza- 1-azoniaadamantane hydrochloride, 1,2-benzisothiazolin-3-one, 4-(2-nitrobutyl) morpholine and 4,4-(2-ethyl-2-nitrotrimethylene) dimorpholine, or the sodium salt of 2-pyridinethiol- 1-oxide as a preservative. Based on a previous observation that the proper selection of the hydraulic fluid employed in the cutting machine is a major factor in controlling rancidity, the possibility of spoilagemore » control by treating the fluid with EDTA alone was also demonstrated; the EDTA had a greater beneficial effect with a synthetic coolant than with an oil emulsion. Published data on the effects of EDTA indicate that it poses no significant water pollution problems upon disposal, exhibits a low order of animal toxicity, and rarely causes human allergies. Tables and 65 references.« less

Evaluation of the performance during hard turning of OHNS steel with minimal cutting fluid application and its comparison with minimum quantity lubrication

NASA Astrophysics Data System (ADS)

Raj, Anil; Wins, K. Leo Dev; Varadarajan, A. S.

2016-09-01

Cutting fluid application plays a significant role in the manufacturing industries that acts as a coolant as well as a lubricant. The conventional flood cooling application of cutting fluids not only increases the production cost on account of the expenses involved in procurement, storage and disposal but also creates serious environmental and health hazards. In order to overcome these negative effects, techniques like Minimum quantity lubrication (MQL) and Minimal Cutting fluid application (MCFA) have increasingly found their way into the area of metal cutting and have already been established as an alternative to conventional wet machining. This paper investigates the effect of minimal Cutting fluid application (MCFA) which involves application of high velocity pulsing jet of proprietary cutting fluids at the contact zones using a special fluid application system. During hard turning of oil hardened non shrinkable steel (OHNS) on cutting temperature and tool wear and to compare the performance with Minimum quantity lubrication (MQL) assisted hard turning in which cutting fluid is carried in a high velocity stream of air. An attempt was also made to compare the performance during Turning with MCFA and MQL application with conventional wet and dry turning by analysing the tool wear pattern using SEM images.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koen, A.D.

This paper reports that oil and gas companies in the US are curbing costs and redirecting spending to survive the worst decline of petroleum industry activity on record. Persistently weak US natural gas prices and shaky oil prices worldwide have put pressure on domestic companies to become low cost producers. Efforts to cut exploration and development costs have depressed activity in the US, one of the world's most mature oil and gas provinces. International E and D hot spots include the UK North Sea, Yemen, Thailand, Myanmar, Pakistan, and Latin America. Prospects in the Commonwealth of Independent States also continuemore » to generate considerable enthusiasm. Operators struggling to survive or searching for funds to spend on non-US prospects are trying to shuck noncore US assets. Other favored cost cutting strategies include reducing and restructuring debt, operating and administrative staffs, and internal organizations. Major integrated companies are able to add value by refocusing refining, petrochemical, or marketing operations. But independents must adapt operations close to the wellhead to become low cost producers. Whatever tactics are used to mitigate effects of low US activity, no domestic company --- from the largest integrated major to the smallest independent producer --- has proven to be immune from the downturn.« less

Tastier and healthier alternatives to French fries.

PubMed

Rommens, Caius M; Shakya, Roshani; Heap, Mark; Fessenden, Kristi

2010-05-01

The effect of both the origin and shape of potato cuts on fry quality was investigated in this study. Linear strips from the inner core of tubers were compared to those from outer tissues, both before and after processing, and strips from either specific tissues or whole peeled tubers were also evaluated against ring-shaped cuts. Both strips and rings had 0.7 cm sides and, in most cases, a volume of 4.9 cm(3). They were analyzed for moisture content, antioxidants, asparagine, and reducing sugars. The material was then blanched, dipped in 0.5% disodium acid pyrophosphate and 0.3% glucose, dried at 77 degrees C, par-fried in soybean oil at 191 degrees C, and finish-fried at 168 degrees C. The fried product was analyzed for sensory characteristics and oil, salt, and acrylamide content. Our results showed that strips from the inner core absorbed 28% more oil and exhibited inferior sensory characteristics compared to strips from the outer parts. The extended drying and frying times needed to match the crispness and flavor of inner strips to those of regularly fried outer strips resulted in a further increased absorption of oil and, importantly, triggered a 163% increase in levels of the toxic Maillard reaction product acrylamide. Potato rings consisted of higher dry matter material, contained more antioxidants, and had a lower surface-to-volume ratio than the conventional linear strips. Upon processing, they also absorbed 22% less oil, contained 26% less salt, and displayed superior sensory properties. Thus, ring fries may represent an attractive alternative to French fries as processed staple food.

Publications - GMC 225 | Alaska Division of Geological & Geophysical

Science.gov Websites

following Alaskan arctic White Hills oil and gas wells: ARCO Alaska Inc. Kavik #1 (75' - 9540'); and BP O'Sullivan, P.B., 1994, Apatite fission track data derived from cuttings of the following Alaskan arctic

Risk Score for Detecting Dysglycemia: A Cross-Sectional Study of a Working-Age Population in an Oil Field in China.

PubMed

Tian, Xiubiao; Liu, Yan; Han, Ying; Shi, Jieli; Zhu, Tiehong

2017-06-11

BACKGROUND Dysglycemia (pre-diabetes or diabetes) in young adults has increased rapidly. However, the risk scores for detecting dysglycemia in oil field staff and workers in China are limited. This study developed a risk score for the early identification of dysglycemia based on epidemiological and health examination data in an oil field working-age population with increased risk of diabetes. MATERIAL AND METHODS Multivariable logistic regression was used to develop the risk score model in a population-based, cross-sectional study. All subjects completed the questionnaires and underwent physical examination and oral glucose tolerance tests. The performance of the risk score models was evaluated using the area under the receiver operating characteristic curve (AUC). RESULTS The study population consisted of 1995 participants, 20-64 years old (49.4% males), with undiagnosed diabetes or pre-diabetes who underwent periodic health examinations from March 2014 to June 2015 in Dagang oil field, Tianjin, China. Age, sex, body mass index, history of high blood glucose, smoking, triglyceride, and fasting plasma glucose (FPG) constituted the Dagang dysglycemia risk score (Dagang DRS) model. The performance of Dagang DRS was superior to m-FINDRISC (AUC: 0.791; 95% confidence interval (CI), 0.773-0.809 vs. 0.633; 95% CI, 0.611-0.654). At the cut-off value of 5.6 mmol/L, the Dagang DRS (AUC: 0.616; 95% CI, 0.592-0.641) was better than the FPG value alone (AUC: 0.571; 95% CI, 0.546-0.596) in participants with FPG <6.1 mmol/L (n=1545, P=0.028). CONCLUSIONS Dagang DRS is a valuable tool for detecting dysglycemia, especially when FPG <6.1 mmol/L, in oil field workers in China.

Geochemistry of Eagle Ford group source rocks and oils from the first shot field area, Texas

USGS Publications Warehouse

Edman, Janell D.; Pitman, Janet K.; Hammes, Ursula

2010-01-01

Total organic carbon, Rock-Eval pyrolysis, and vitrinite reflectance analyses performed on Eagle Ford Group core and cuttings samples from the First Shot field area, Texas demonstrate these samples have sufficient quantity, quality, and maturity of organic matter to have generated oil. Furthermore, gas chromatography and biomarker analyses performed on Eagle Ford Group oils and source rock extracts as well as weight percent sulfur analyses on the oils indicate the source rock facies for most of the oils are fairly similar. Specifically, these source rock facies vary in lithology from shales to marls, contain elevated levels of sulfur, and were deposited in a marine environment under anoxic conditions. It is these First Shot Eagle Ford source facies that have generated the oils in the First Shot Field. However, in contrast to the generally similar source rock facies and organic matter, maturity varies from early oil window to late oil window in the study area, and these maturity variations have a pronounced effect on both the source rock and oil characteristics. Finally, most of the oils appear to have been generated locally and have not experienced long distance migration. 

The effects of railway transportation on the enrichment of heavy metals in the artificial soil on railway cut slopes.

PubMed

Chen, Zhaoqiong; Wang, KeXiu; Ai, Ying Wei; Li, Wei; Gao, Hongying; Fang, Chen

2014-02-01

Heavy metal contamination in the artificial soils on the railway cut slopes may have great influence on the revegetation of the cut slopes. The purpose of this study was to assess the variation of heavy metal contamination levels with railway operation time and analyze their possible resources. A total of 100 soil samples from four cut slopes, which were affected by railway transportation for different years, were analyzed for metal pollution (Cd, Pb, Cr, Cu, Zn, Fe). The concentrations of Cd, Pb showed increasing trend with increasing operation time of railways, while such trend was not found in Cr, Cu, Zn, Fe. According to the soil quality standard of China, Cd was considered to have considerable contamination, while Pb has less, but Cr, Cu, Zn, Fe have none. Moreover, cadmium exhibited remarkably higher levels rather than those reported in other studies. Enrichment factors and ecological index showed that Cd and Pb showed a moderate enrichment and a considerable ecological risk in most of the soil samples. The results of descriptive statistic, principal component analysis, cluster analysis and correlation analysis were totally consistent with each other. Their results revealed that Cr, Cu, Zn and Fe had common origins, and they may come from natural resources. While Cd and Pb were significantly influenced by railway transportation, leaked cargos, fuel combustion, the use of lubricate oils and sleeper impregnation oils during railway transportation may be their main resources.

GC-MS analysis of clove (Syzygium aromaticum) bud essential oil from Java and Manado

NASA Astrophysics Data System (ADS)

Amelia, B.; Saepudin, E.; Cahyana, A. H.; Rahayu, D. U.; Sulistyoningrum, A. S.; Haib, J.

2017-07-01

The largest clove production contributors in Indonesia are mostly coming from Java and Manado. Different flavor among clove origins is caused by chemical constituents in clove oil. Unfortunately, scientific research and publications about flavor in clove from Indonesia's origin are still limited. The objective of this research is to determine significant differences of constituents in terms of flavor in clove oil originated from Java and Manado. The essential oils were isolated from cut clove bud samples by steam distillation method. The chemical constituents of clove bud oil were analyzed by using gas chromatography-mass spectrometry (GC-MS). Constituents were then identified by comparing the results of the chromatogram and reference retention time using Wiley mass spectra library (Wiley W9N11). Thirty-six and thirty-four chemical constituents were identified based on GC-MS from clove oil collected from Java and Manado, respectively. Major classes of compounds are sesquiterpenes, phenyl propanoid, oxygenated sesquiterpenes, and esters. Different compositions in major constituents were found between both origins. Clove Java contained eugenol (55.60 %), eugenyl acetate (20.54 %), caryophyllene (14.84 %), and α-humulene (2.75 %). While, in clove Manado, the composition were eugenol (74.64 %), caryophyllene (12.79 %), eugenyl acetate (8.70 %), and α-humulene (1.53 %). Moreover, minor constituents β-elemene (0.04 %), α-cadinene (0.05 %) and ledol (0.06 %) were existed only in clove Java, while clove Manado had some unique minor constituents which were not found in clove Java, i.e. β-gurjunene (0.04 %), γ-cadinene %), and humulene oxide (0.05 %). In conclusion, both clove oils from Java and Manado contained same major chemical constituents but different in their composition. In addition, some minor constituents existed only in specific origin.

Classification of Amazonian rosewood essential oil by Raman spectroscopy and PLS-DA with reliability estimation.

PubMed

Almeida, Mariana R; Fidelis, Carlos H V; Barata, Lauro E S; Poppi, Ronei J

2013-12-15

The Amazon tree Aniba rosaeodora Ducke (rosewood) provides an essential oil valuable for the perfume industry, but after decades of predatory extraction it is at risk of extinction. The extraction of the essential oil from wood implies the cutting of the tree, and then the study of oil extracted from the leaves is important as a sustainable alternative. The goal of this study was to test the applicability of Raman spectroscopy and Partial Least Square Discriminant Analysis (PLS-DA) as means to classify the essential oil extracted from different parties (wood, leaves and branches) of the Brazilian tree A. rosaeodora. For the development of classification models, the Raman spectra were split into two sets: training and test. The value of the limit that separates the classes was calculated based on the distribution of samples of training. This value was calculated in a manner that the classes are divided with a lower probability of incorrect classification for future estimates. The best model presented sensitivity and specificity of 100%, predictive accuracy and efficiency of 100%. These results give an overall vision of the behavior of the model, but do not give information about individual samples; in this case, the confidence interval for each sample of classification was also calculated using the resampling bootstrap technique. The methodology developed have the potential to be an alternative for standard procedures used for oil analysis and it can be employed as screening method, since it is fast, non-destructive and robust. © 2013 Elsevier B.V. All rights reserved.

Energy War Is Generating Jobs

ERIC Educational Resources Information Center

Fiester, Kenneth

1977-01-01

Describes various energy-related projects and legislation, with new job estimates, to improve or design buildings and methods to reduce the annual growth in energy consumption by reducing gasoline consumption, cutting oil imports, increasing coal production, insulating buildings, and installing solar energy devices. (MF)

Publications - GMC 245 | Alaska Division of Geological & Geophysical

Science.gov Websites

the Norton Sound Exxon Corporation OCS Y-0407-1 (Yellow Pup #1) well Authors: Stone, Fred, Mobil Oil , 1995, Pyromat kinetic model of coal from cuttings (9,220-9,260') of the Norton Sound Exxon Corporation

Life cycle inventory for palm based plywood: A gate-to-gate case study

NASA Astrophysics Data System (ADS)

Ahmad, Shamim; Sahid, Ismail; Subramaniam, Vijaya; Muhamad, Halimah; Mokhtar, Anis

2013-11-01

The oil palm industry heavily relies on the world market. It is essential to ensure that the oil palm industry is ready to meet the demands and expectation of these overseas customers on the environmental performance of the oil palm industry. Malaysia produces 13.9 million tons of oil palm biomass including oil palm trunk (OPT), frond and empty fruits bunches (EFB) annually. OPT felled in some oil palm plantations during replanting is transported to various industries and one such industry is the plywood factories. In order to gauge the environmental performance of the use of OPT as plywood a Life Cycle Assessment (LCA) study was conducted for palm based plywood. LCA is an important tool to assess the environmental performance of a product or process. Life cycle inventory (LCI) is the heart of a LCA study. This LCI study has a gate-to-gate system boundary and the functional unit is 1 m3 palm plywood produced and covers three types of plywood; Moisture Resistance Plywood (MR), Weather Boiling Proof Plywood Grade 1 (WBP Grade 1) at Factory D and Weather Boiling Proof Plywood Grade 2 (WBP Grade 2) at Factory E. Both factories use two different types of drying processes; conventional drying at Factory D and kiln drying at Factory E. This inventory data was collected from two factories (D and E) representing 40% of Malaysia palm plywood industry. The inputs are mainly the raw materials which are the oil palm trunks and tropical wood veneers and the energy from diesel and electricity from grid which is mainly used for the drying process. The other inputs include water, urea formaldehyde, phenol formaldehyde, flour and melamine powder. The outputs are the biomass waste which consists of oil palm trunk off-cut and emission from boiler. Generally, all types of plywood production use almost same materials and processing methods in different quantities. Due to the different process efficiency, Factory D uses less input of raw materials and energy compared to Factory E.

Singlet oxygen autoxidation of vegetable oils: evidences for lack of synergy between β-carotene and tocopherols.

PubMed

Smyk, Bogdan

2015-09-01

The synergy between β-carotene and tocopherols--antioxidants protecting oils from oxidation, was analyzed in a model system. The model used stripped borage and evening primrose oils. A chlorophyll extract, β-carotene and one of the tocopherols were added together or separately to the oils. Oil oxidation was initiated by singlet oxygen that was produced by chlorophylls irradiated with the use of a xenon lamp equipped with the cut-off 600 nm filter. Experiments were carried out at two mole ratios of tocopherols to β-carotene, i.e. at 1:1 and 23:1. Analyses were performed using absorption and fluorescence spectra in the UV+Vis region. The results demonstrated an antagonistic action of the antioxidants. The protective effect of unsaturated fatty acids was significantly better in the case of β-carotene compared to the tocopherols. Furthermore, tocopherols were less effective in protecting the oils in the presence of β-carotene than without it. Copyright © 2015 Elsevier Ltd. All rights reserved.

Desolventizing of soybean oil/azeotrope mixtures using ceramic membranes.

PubMed

de Melo, Jonas R M; Tiggeman, Lidia; Rezzadori, Katia; Steffens, Juliana; Palliga, Marshall; Oliveira, J Vladimir; Di Luccio, Marco; Tres, Marcus V

2017-08-01

This work investigates the use of ceramic membranes with different molecular weight cut-offs (MWCOs: 5, 10 and 20 kDa) to desolventize azeotropic solvent mixtures (ethanol/n-hexane and isopropyl alcohol/n-hexane) from soybean oil/azeotrope micelles. Results show that a decrease in the MWCO of a membrane and an increase in the solvent mass ratio in the mixture resulted in a significant reduction in the permeate flux. The 20 kDa membrane presented the highest permeate flux, 80 and 60 kg/m 2 h for the soybean oil/n-hexane/isopropyl alcohol and soybean oil/n-hexane/ethanol azeotropes, respectively, for an oil to solvent ratio of 1:3 (w/w). The highest oil retention was found using the n-hexane/isopropyl alcohol azeotrope, around 25% in the membrane with the lowest MWCO, that is, 5 kDa. It is shown that the azeotropic mixtures provided intermediate characteristics compared to the original pure solvent behavior.

An overview on source rocks and the petroleum system of the central Upper Rhine Graben

NASA Astrophysics Data System (ADS)

Böcker, Johannes; Littke, Ralf; Forster, Astrid

2017-03-01

The petroleum system of the Upper Rhine Graben (URG) comprises multiple reservoir rocks and four major oil families, which are represented by four distinct source rock intervals. Based on geochemical analyses of new oil samples and as a review of chemical parameter of former oil fields, numerous new oil-source rock correlations were obtained. The asymmetric graben resulted in complex migration pathways with several mixed oils as well as migration from source rocks into significantly older stratigraphic units. Oldest oils originated from Liassic black shales with the Posidonia Shale as main source rock (oil family C). Bituminous shales of the Arietenkalk-Fm. (Lias α) show also significant source rock potential representing the second major source rock interval of the Liassic sequence. Within the Tertiary sequence several source rock intervals occur. Early Tertiary coaly shales generated high wax oils that accumulated in several Tertiary as well as Mesozoic reservoirs (oil family B). The Rupelian Fish Shale acted as important source rock, especially in the northern URG (oil family D). Furthermore, early mature oils from the evaporitic-salinar Corbicula- and Lower Hydrobienschichten occur especially in the area of the Heidelberg-Mannheim-Graben (oil family A). An overview on potential source rocks in the URG is presented including the first detailed geochemical source rock characterization of Middle Eocene sediments (equivalents to the Bouxwiller-Fm.). At the base of this formation a partly very prominent sapropelic coal layer or coaly shale occurs. TOC values of 20-32 % (cuttings) and Hydrogen Index (HI) values up to 640-760 mg HC/g TOC indicate an extraordinary high source rock potential, but a highly variable lateral distribution in terms of thickness and source rock facies is also supposed. First bulk kinetic data of the sapropelic Middle Eocene coal and a coaly layer of the `Lymnäenmergel' are presented and indicate oil-prone organic matter characterized by low activation energies. These sediments are considered as most important source rocks of numerous high wax oils (oil family B) in addition to the coaly source rocks from the (Lower) Pechelbronn-Schichten (Late Eocene). Migration pathways are significantly influenced by the early graben evolution. A major erosion period occurred during the latest Cretaceous. The uplift center was located in the northern URG area, resulting in SSE dipping Mesozoic strata in the central URG. During Middle Eocene times a second uplift center in the Eifel area resulted in SW-NE-directed shore lines in the central URG and contemporaneous south-southeastern depocenters during marine transgression from the south. This structural setting resulted in a major NNW-NW-directed and topography-driven migration pattern for expelled Liassic oil in the fractured Mesozoic subcrop below sealing Dogger α clays and basal Tertiary marls.

BP pledges to cut emissions

NASA Astrophysics Data System (ADS)

Showstack, Randy

British Petroleum (BP), one of the world's biggest oil companies that could become even bigger if a merger with Amoco is approved, announced on September 18 that it will cut its emissions of greenhouse gases by 10% from a 1990 baseline of 40 million tons of carbon dioxide between now and the year 2010.The target, which is double the amount of emissions reductions that industrialized nations agreed to under the Kyoto protocol on climate change, will now stand next to BP's financial targets, said John Browne, group chief executive of BP.

Mechanisms Of Saucer-Shaped Sill Emplacement: Insight From Experimental Modeling

NASA Astrophysics Data System (ADS)

Galland, O.; Planke, S.; Malthe-Sørenssen, A.; Polteau, S.; Svensen, H.; Podladchikov, Y. Y.

2006-12-01

It has been recently demonstrated that magma intrusions in sedimentary basins had a strong impact on petroleum systems. Most of these intrusions are sills, and especially saucer-shaped sills. These features can be observed in many sedimentary basins (i.e. the Karoo basin, South Africa; the Norwegian and North Sea; the Tunguska basin, Siberia; the Neuquén basin in Argentina). The occurrence of such features in so various settings suggests that their emplacement results from fundamental processes. However, the mechanisms that govern their formation remain poorly constrained. Experiments were conducted to simulate the emplacement of saucer-shaped magma intrusions in sedimentary basins. The model rock and magma were fine-grained silica flour and molten vegetable oil, respectively. This modeling technique allows simultaneous simulation of magma emplacement and brittle deformation at a basin scale. For our purpose, we performed our experiments without external deformation. During the experiments, the oil was injected horizontally at constant flow rate within the silica flour. Then the oil initially emplaced in a sill, whereas the surface of the model inflated into a smooth dome. Subsequently, the oil propagated upwards along inclined sheets, finally reaching the surface at the edge of the dome. The resulting geometries of the intrusions were saucer-shaped sills. Then the oil solidified, and the model was cut in serial cross-sections through which the structures of the intrusive body and of the overburden can be observed. In order to constraint the processes governing the emplacement of such features, we performed a parametric study based on a set of experiments in which we systematically varied parameters such as the depth of emplacement and the injection flow rate of the oil. Our results showed that saucer diameters are larger at deeper level of emplacement. Opposite trend was obtained with varying injection flow rates. Based on our results, we conducted a detailed physical analysis that resulted in the definition of a dimensionless parameter that governs the emplacement of saucers.

Mapping deep aquifer salinity trends in the southern San Joaquin Valley using borehole geophysical data constrained by chemical analyses

NASA Astrophysics Data System (ADS)

Gillespie, J.; Shimabukuro, D.; Stephens, M.; Chang, W. H.; Ball, L. B.; Everett, R.; Metzger, L.; Landon, M. K.

2016-12-01

The California State Water Resources Control Board and the California Division of Oil, Gas and Geothermal Resources are collaborating with the U.S. Geological Survey to map groundwater resources near oil fields and to assess potential interactions between oil and gas development and groundwater resources. Groundwater resources having salinity less than 10,000 mg/L total dissolved solids may be classified as Underground Sources of Drinking Water (USDW) and subject to protection under the federal Safe Drinking Water Act. In this study, we use information from oil well borehole geophysical logs, oilfield produced water and groundwater chemistry data, and three-dimensional geologic surfaces to map the spatial distribution of salinity in aquifers near oil fields. Salinity in the southern San Joaquin Valley is controlled primarily by depth and location. The base of protected waters occurs at very shallow depths, often < 300 meters, in the western part of the valley where aquifer recharge is low in the rain shadow of the Coast Ranges. The base of protected water is much deeper, often >1,500 meters, in the eastern part of the San Joaquin Valley where higher runoff from the western slopes of the Sierra Nevada provide relatively abundant aquifer recharge. Stratigraphy acts as a secondary control on salinity within these broader areas. Formations deposited in non-marine environments are generally fresher than marine deposits. Layers isolated vertically between confining beds and cut off from recharge sources may be more saline than underlying aquifers that outcrop in upland areas on the edge of the valley with more direct connection to regional recharge areas. The role of faulting is more ambiguous. In some areas, abrupt changes in salinity may be fault controlled but, more commonly, the faults serve as traps separating oil-bearing strata that are exempt from USDW regulations, from water-bearing strata that are not exempt.

The evaluation of the optimization design and application effect of same-well-injection-production technique’s injection-production circulatory system

NASA Astrophysics Data System (ADS)

Guoxing, Zheng; Minghu, Jiang; Hongliang, Gong; Nannan, Zhang; Jianguang, Wei

2018-02-01

According to basic principles of combining series of strata and demands of same-well injection-production technique, the optimization designing method of same-well injection-production technique’s injection-production circulatory system is given. Based on oil-water two-phase model with condition of arbitrarily well network, a dynamic forecast method for the application of same-well injection-production reservoir is established with considering the demands and capacity of same-well injection-production technique, sample wells are selected to launch the forecast evaluation and analysis of same-well injection-production reservoir application’s effect. Results show: single-test-well composite water cut decreases by 4.7% and test-well-group composite water cut decreases by 1.56% under the condition of basically invariant ground water injection rate. The method provides theoretical support for the proof of same-well injection-production technique’s reservoir development improving effect and further tests.

The Determination of Several Spray Characteristics of a High-Speed Oil Engine Injection System with an Oscilloscope

NASA Technical Reports Server (NTRS)

Hicks, Chester W; Moore, Charles S

1928-01-01

An investigation was conducted to determine the injection lag, duration of injection, and spray start and cut-off characteristics of a fuel injection system operated on an engine and injecting fuel into the atmosphere.

High Resolution DNS of Turbulent Flows using an Adaptive, Finite Volume Method

NASA Astrophysics Data System (ADS)

Trebotich, David

2014-11-01

We present a new computational capability for high resolution simulation of incompressible viscous flows. Our approach is based on cut cell methods where an irregular geometry such as a bluff body is intersected with a rectangular Cartesian grid resulting in cut cells near the boundary. In the cut cells we use a conservative discretization based on a discrete form of the divergence theorem to approximate fluxes for elliptic and hyperbolic terms in the Navier-Stokes equations. Away from the boundary the method reduces to a finite difference method. The algorithm is implemented in the Chombo software framework which supports adaptive mesh refinement and massively parallel computations. The code is scalable to 200,000 + processor cores on DOE supercomputers, resulting in DNS studies at unprecedented scale and resolution. For flow past a cylinder in transition (Re = 300) we observe a number of secondary structures in the far wake in 2D where the wake is over 120 cylinder diameters in length. These are compared with the more regularized wake structures in 3D at the same scale. For flow past a sphere (Re = 600) we resolve an arrowhead structure in the velocity in the near wake. The effectiveness of AMR is further highlighted in a simulation of turbulent flow (Re = 6000) in the contraction of an oil well blowout preventer. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Advanced Scientific Computing Research, Applied Mathematics program under Contract Number DE-AC02-05-CH11231.

Mechanical and phytochemical protection mechanisms of Calligonum comosum in arid deserts

PubMed Central

Mohammad, Mohammad G.; El-Keblawy, Ali A.; Omar, Hany; Abouleish, Mohamed; Madkour, Mohamed; Elnaggar, Attiat; Hosni, Racha M.

2018-01-01

Unlike animals, plants are sessile organisms, lacking circulating antibodies and specialized immune cells and are exposed to various harsh environmental conditions that make them at risk of being attacked by different pathogens and herbivores. Plants produce chemo-signals to respond to the surroundings and be able to distinguish between harmless and harmful signals. In this study, the production of phytochemicals as plant signaling mechanisms and their defensive roles in disease resistance and repelling herbivores are examined in Calligonum comosum. C. comosum is a leafless standalone perennial shrub widespread in sand dunes. The plant has the ability to survive the drastic environmental conditions of the arid/ hyperarid deserts of the Arabia. Structural anatomy and phytochemicals analyses were used to identify both mechanical and chemical defensive mechanisms in C. comosum. Microscopy-based investigations indicated that stems of this species developed hard structures in its outer layers including sclerenchyma and cluster crystals of calcium oxalate (CaOx). Sclerenchyma and CaOx are difficult to be eaten by herbivores and insects and can harm their mouthparts. On the other hand, the plant developed both short-distance (local) and long-distance (systematic over limited sphere) phytochemicals-producing cells located at its outer regions that is surrounding the inner nutrient-rich vascular system (VS). Local chemical was represented by phenolic idioblasts that were released in response to plant cutting. Systematic chemical was represented by toxic volatile oil containing ~50% benzaldehyde derivative (cuminaldehyde). The oil caused strong killing effect on both mammalian cells and microbial pathogens via either direct addition or indirect exposure to its vapor. The plants lost the oil content and allowed fungal growth once cut and dried. The localization of both defensive mechanisms to the outer region of the plant seemed to protect the inner nutrient-rich VS and hence maintained the plant survival. Surprisingly, in relation to traditional folklore use as medicine, local people use only green parts of the plant and only during the winter, where the plant found devoid of volatile oil and phenolic idioblasts. Moreover, it turns into recommendations for local people to avoid any health problems caused by the plant supply. PMID:29415032

Decomposition of PCBs in transformer oil using an electron beam accelerator

NASA Astrophysics Data System (ADS)

Jung, In-Ha; Lee, Myun-Joo; Mah, Yoon-Jung

2012-07-01

Decomposition of PCBs in commercially used transformer oil used for more than 30 years has been carried out at normal temperature and pressure without any additives using an electron beam accelerator. The experiments were carried out in two ways: batch and continuous pilot plant with 1.5 MeV of energy, a 50 mA current, and 75 kW of power in a commercial scale accelerator. The electron beam irradiation seemed to transform large molecular weight compounds into lower ones, but the impact was considered too small on the physical properties of oil. Residual concentrations of PCBs after irradiation depend on the absorption dose of the electron beam energy, but aliphatic chloride compounds were produced at higher doses of irradiation. As the results from FT-NMR, chloride ions decomposed from the PCBs are likely to react with aliphatic hydro carbon compounds rather than existing as free radical ions in the transformer oil. Since this is a dry process, treated oil can be used as cutting oil or machine oil for heavy equipment without any additional treatments.

Nanofluid as coolant for grinding process: An overview

NASA Astrophysics Data System (ADS)

Kananathan, J.; Samykano, M.; Sudhakar, K.; Subramaniam, S. R.; Selavamani, S. K.; Manoj Kumar, Nallapaneni; Keng, Ngui Wai; Kadirgama, K.; Hamzah, W. A. W.; Harun, W. S. W.

2018-04-01

This paper reviews the recent progress and applications of nanoparticles in lubricants as a coolant (cutting fluid) for grinding process. The role of grinding machining in manufacturing and the importance of lubrication fluids during material removal are discussed. In grinding process, coolants are used to improve the surface finish, wheel wear, flush the chips and to reduce the work-piece thermal deformation. The conventional cooling technique, i.e., flood cooling delivers a large amount of fluid and mist which hazardous to the environment and humans. Industries are actively looking for possible ways to reduce the volume of coolants used in metal removing operations due to the economical and ecological impacts. Thus as an alternative, an advanced cooling technique known as Minimum Quantity Lubrication (MQL) has been introduced to the enhance the surface finish, minimize the cost, to reduce the environmental impacts and to reduce the metal cutting fluid consumptions. Nanofluid is a new-fangled class of fluids engineered by dispersing nanometre-size solid particles into base fluids such as water, lubrication oils to further improve the properties of the lubricant or coolant. In addition to advanced cooling technique review, this paper also reviews the application of various nanoparticles and their performance in grinding operations. The performance of nanoparticles related to the cutting forces, surface finish, tool wear, and temperature at the cutting zone are briefly reviewed. The study reveals that the excellent properties of the nanofluid can be beneficial in cooling and lubricating application in the manufacturing process.

Agronomic and chemical evaluation of smooth sumac, Rhus glabra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, T.A.

Smooth sumac (Rhus glabra) is a potential whole-plant source of polyphenol and oil. In a 2-yr evaluation of progenies from 14 Maryland, 1 northern Virginia, and 2 Georgia populations, highly significant variation (1% level) in vigor, number of plants surviving the seeding year, dry matter yield the seeding year, and number of tillers produced the second year was observed. In 15 entries, highly significant variation (1% level) in polyphenol + oil and in gallotannins was observed. Dry matter yields, extrapolated to Mg ha/sup -1/, ranged from 0.02 to 1.4 (for a single harvest), % polyphenol + oil from 19.4-31.1, andmore » % gallotannins (a class of polyphenols) from 9.8 to 15.7. It is suggested that significantly improved lines could be developed through breeding. Based on estimated ratios of sigma/sup 2//sub Entries//sigma/sup 2//sub Entries/ + sigma/sup 2/, genetic variation for most agronomic traits could be estimated with fair precision whereas variation for chemical traits could be affected substantially by nongenetic factors. Factor analysis indicated plants that would perform reasonably well over a 2-yr period could be selected on the basis of early seeding-year vigor scores. Selection for high amount of polyphenol + oil and gallotannins would have to be done independently of agronomic selection. Cutting frequencies should not exceed 2 x yr/sup -1/ or serious stand loss would occur.« less

JPRS Report Near East & South Asia Pakistan.

DTIC Science & Technology

1992-07-21

cutlery and surgical equipment industries. -Import of machinery, spares and accessories for cut- lery industry has been allowed free of customs duty...pulses worth $58 million, edible oil worth $400 million during the year 1991-92. Federal Budget, Military Expenditures Criticized 92AS1113C Lahore

29 CFR 520.300 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... from leather or from any shoe-upper material of all cut stock and findings for footwear, including bows...) Rainwear means the manufacture of waterproofed garments and raincoats from oiled cloth or other materials... negligees from woven fabrics; corsets and other body supporting garments from any material; infants' and...

29 CFR 520.300 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... from leather or from any shoe-upper material of all cut stock and findings for footwear, including bows...) Rainwear means the manufacture of waterproofed garments and raincoats from oiled cloth or other materials... negligees from woven fabrics; corsets and other body supporting garments from any material; infants' and...

29 CFR 520.300 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... from leather or from any shoe-upper material of all cut stock and findings for footwear, including bows...) Rainwear means the manufacture of waterproofed garments and raincoats from oiled cloth or other materials... negligees from woven fabrics; corsets and other body supporting garments from any material; infants' and...

A Better Way to Burn Wood.

ERIC Educational Resources Information Center

Robison, Rita

1979-01-01

Wood pyrolysis is a process that burns wood without air, producing gas and oil that are then burned for heat. Now being tested at Maryville College, Tennessee, the process is expected to cut fuel costs, solve a waste disposal problem, and produce charcoal for sale. (Author/MLF)

40 CFR 435.11 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... showers, eye-wash stations, hand-wash stations, fish cleaning stations, and galleys located within... formation oil carried out from the wellbore with the drilling fluid. (2) Dry drill cuttings means the... limitations and NSPS means the concentration (milligrams/kilogram dry sediment) of the drilling fluid in...

Publications - GMC 190 | Alaska Division of Geological & Geophysical

Science.gov Websites

core (9,634.5'-9,671.5') from the Tenneco Oil Company OCS Y-0943-1 (Aurora) well Authors: Unknown Reference Unknown, 1991, Vitrinite reflectance data of cuttings (1,080'-18,325') and core (9,634.5'-9,671.5

Continuous freeway illumination and accidents on a section of Rte. I-95.

DOT National Transportation Integrated Search

1978-01-01

Beginning with the oil embargo of 1973-74, highway lighting and particularly continuous lighting on freeways became one of the first items to be cut back to conserve energy and revenue. During this period of energy shortage, considerable lighting was...

Boiler MACT Technical Assistance (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2012-03-01

Fact sheet describing the changes to Environmental Protection Act process standards. The DOE will offer technical assistance to ensure that major sources burning coal and oil have information on cost-effective, clean energy strategies for compliance, and to promote cleaner, more efficient boiler burning to cut harmful pollution and reduce operational costs. The U.S. Environmental Protection Agency (EPA) is expected to finalize the reconsideration process for its Clean Air Act pollution standards National Emissions Standards for Hazardous Air Pollutants for Major Sources: Industrial, Commercial, and Institutional Boilers and Process Heaters (known as Boiler Maximum Achievable Control Technology (MACT)), in Spring 2012.more » This rule applies to large and small boilers in a wide range of industrial facilities and institutions. The U.S. Department of Energy (DOE) will offer technical assistance to ensure that major sources burning coal or oil have information on cost-effective clean energy strategies for compliance, including combined heat and power, and to promote cleaner, more efficient boilers to cut harmful pollution and reduce operational costs.« less

Analysis of chain saw lubricating oils commonly used in Thailand's southern border provinces for forensic science purpose.

PubMed

Choodum, Aree; Tripuwanard, Kijja; Daeid, Niamh Nic

2014-08-01

In recent years, Thailand's southern border provinces (Malay-Muslim-majority border provinces) have become the scene of violence and insurgency. One of the attack patterns is the blocking of roads with perennial plants followed by planned attacks using improvised explosive devices (IEDs) or weapons on first responders. Containers of viscous dark lubricating oil and traces of lubricants on the felled trees were usually found at the scene. These were suspected to be chain oil lubricant from the chainsaws used to cut down the trees used for the roadblock. This work aimed to differentiate the chromatographic patterns of used lubricating oils available in automobile repair shops from various locations across Thailand's southern border provinces. Lubricating oils were analyzed using gas chromatography/flame ionization detector (GC/FID) every two weeks to study their variation in chemical compositions over time. The results obtained from GC/FID were normalized for differentiation. This included four two-stroke, six four-stroke, and three recycled oils. Two lubricating oils found at an incident scene were also analyzed and the results compared with the chain oil from five seized chainsaws. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Leaf-cutting ants: an unexpected microenvironment holding human opportunistic black fungi.

PubMed

Duarte, A P M; Attili-Angelis, D; Baron, N C; Forti, L C; Pagnocca, F C

2014-09-01

Fungus-growing ants of the genus Atta are known for their leaf-cutting habit, a lifestyle they have maintained since their 50-million-year-old co-evolution with a mutualistic fungus, cultivated as food. Recent studies have highlighted that, in addition to the mutualistic fungus, nests of ants harbor a great diversity of microbial communities. Such microorganisms include the dematiaceous fungi, which are characterized by their melanized cell walls. In order to contribute to the knowledge of fungal ecology, as well as opportunistic strains that may be dispersed by these social insects, we isolated and identified fungi carried by gynes of Atta capiguara and Atta laevigata, collected from colonies located in Fazenda Santana, Botucatu (São Paulo, Brazil). The isolation was carried out using the oil flotation technique, which is suitable for the growth of black fungi. Inoculated plates were incubated at 25 and 35 °C until black cultures were visible (20-45 days). Isolates were identified based on microscopic and molecular characteristics. Some isolated genera were: Cladophialophora, Cladosporium, Exophiala, Ochroconis, Phaeococcomyces, Phialophora and Penidiella. Hyaline species were also found. The results obtained from this work showed that leaf-cutting gynes may contribute to the dispersal of opportunistic dematiaceous fungi. It is suggested that more attention should be paid to this still unexplored subject.

Measuring Concentrations of Dissolved Methane and Ethane and the 13 C of Methane in Shale and Till.

PubMed

Hendry, M Jim; Barbour, S Lee; Schmeling, Erin E; Mundle, Scott O C

2017-01-01

Baseline characterization of concentrations and isotopic values of dissolved natural gases is needed to identify contamination caused by the leakage of fugitive gases from oil and gas activities. Methods to collect and analyze baseline concentration-depth profiles of dissolved CH 4 and C 2 H 6 and δ 13 C-CH 4 in shales and Quaternary clayey tills were assessed at two sites in the Williston Basin, Canada. Core and cuttings samples were stored in Isojars ® in a low O 2 headspace prior to analysis. Measurements and multiphase diffusion modeling show that the gas concentrations in core samples yield well-defined and reproducible depth profiles after 31-d equilibration. No measurable oxidative loss or production during core sample storage was observed. Concentrations from cuttings and mud gas logging (including IsoTubes ® ) were much lower than from cores, but correlated well. Simulations suggest the lower concentrations from cuttings can be attributed to drilling time, and therefore their use to define gas concentration profiles may have inherent limitations. Calculations based on mud gas logging show the method can provide estimates of core concentrations if operational parameters for the mud gas capture cylinder are quantified. The δ 13 C-CH 4 measured from mud gas, IsoTubes ® , cuttings, and core samples are consistent, exhibiting slight variations that should not alter the implications of the results in identifying the sources of the gases. This study shows core and mud gas techniques and, to a lesser extent, cuttings, can generate high-resolution depth profiles of dissolved hydrocarbon gas concentrations and their isotopes. © 2016, National Ground Water Association.

[News on occupational contact dermatitis].

PubMed

Crépy, Marie-Noëlle; Bensefa-Colas, Lynda

2014-03-01

Contact dermatitis--irritant contact dermatitis, allergic contact dermatitis and protein contact dermatitis--are the most common occupational skin diseases, most often localized to the hands. Contact urticaria is rarer The main occupational irritants are wet work, detergents and disinfectants, cutting oils, and solvents. The main occupational allergens are rubber additives, metals (chromium, nickel, cobalt), plastics (epoxy resins, acrylic), biocides and plants. Diagnosis is based on clinical examination, medical history and allergy testing. For a number of irritating or sensitizing agents, irritant or allergic dermatitis can be notified as occupational diseases. The two main prevention measures are reducing skin contact with irritants and complete avoidance of skin contact with offending allergens.

Great Lakes Demonstration 2

DTIC Science & Technology

2012-06-01

A-8 Figure A-12. Laser fluorometer...District Response Advisory Team DRMM Dynamic Risk Management Model EPA Environmental Protection Agency FL Laser fluorometer FOSC Federal On-Scene...this tactic. During this evolution the Hollyhock experimented applying its ice-breaking capabilities to cut channels and pockets into the ice for oil

Screening cut-stump control of Chinese tallowtree, sweetgum and yaupon with aminocyclopyrachlor

Treesearch

J. L. Yeiser; M. Link; J. Grogan

2012-01-01

Aminocyclopyrachlor (MAT28) was investigated for the potential control of unwanted woody rootstocks of Chinese tallowtree (Triadica sebifera), sweetgum (Liquidambar styraciflua), and yaupon (Ilex vomitoria). A cutstump application of MAT28+Brush and Basal Oil by Helena was tested against standard treatments: (1)...

2007 SB14 Source Reduction Plan/Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, L

2007-07-24

Aqueous solutions (mixed waste) generated from various LLNL operations, such as debris washing, sample preparation and analysis, and equipment maintenance and cleanout, were combined for storage in the B695 tank farm. Prior to combination the individual waste streams had different codes depending on the particular generating process and waste characteristics. The largest streams were CWC 132, 791, 134, 792. Several smaller waste streams were also included. This combined waste stream was treated at LLNL's waste treatment facility using a vacuum filtration and cool vapor evaporation process in preparation for discharge to sanitary sewer. Prior to discharge, the treated waste streammore » was sampled and the results were reviewed by LLNL's water monitoring specialists. The treated solution was discharged following confirmation that it met the discharge criteria. A major source, accounting for 50% for this waste stream, is metal machining, cutting and grinding operations in the engineering machine shops in B321/B131. An additional 7% was from similar operations in B131 and B132S. This waste stream primarily contains metal cuttings from machined parts, machining coolant and water, with small amounts of tramp oil from the machining and grinding equipment. Several waste reduction measures for the B321 machine shop have been taken, including the use of a small point-of-use filtering/tramp-oil coalescing/UV-sterilization coolant recycling unit, and improved management techniques (testing and replenishing) for coolants. The recycling unit had some operational problems during 2006. The machine shop is planning to have it repaired in the near future. A major source, accounting for 50% for this waste stream, is metal machining, cutting and grinding operations in the engineering machine shops in B321/B131. An additional 7% was from similar operations in B131 and B132S. This waste stream primarily contains metal cuttings from machined parts, machining coolant and water, with small amounts of tramp oil from the machining and grinding equipment. Several waste reduction measures for the B321 machine shop have been taken, including the use of a small point-of-use filtering/tramp-oil coalescing/UV-sterilization coolant recycling unit, and improved management techniques (testing and replenishing) for coolants. The recycling unit had some operational problems during 2006. The machine shop is planning to have it repaired in the near future. Quarterly waste generation data prepared by the Environmental Protection Department's P2 Team are regularly provided to engineering shops as well as other facilities so that generators can track the effectiveness of their waste minimization efforts.« less

Well logging interpretation of production profile in horizontal oil-water two phase flow pipes

NASA Astrophysics Data System (ADS)

Zhai, Lu-Sheng; Jin, Ning-De; Gao, Zhong-Ke; Zheng, Xi-Ke

2012-03-01

Due to the complicated distribution of local velocity and local phase hold up along the radial direction of pipe in horizontal oil-water two phase flow, it is difficult to measure the total flow rate and phase volume fraction. In this study, we carried out dynamic experiment in horizontal oil-water two phases flow simulation well by using combination measurement system including turbine flowmeter with petal type concentrating diverter, conductance sensor and flowpassing capacitance sensor. According to the response resolution ability of the conductance and capacitance sensor in different range of total flow rate and water-cut, we use drift flux model and statistical model to predict the partial phase flow rate, respectively. The results indicate that the variable coefficient drift flux model can self-adaptively tone the model parameter according to the oil-water two phase flow characteristic, and the prediction result of partial phase flow rate of oil-water two phase flow is of high accuracy.

Inspection of wear particles in oils by using a fuzzy classifier

NASA Astrophysics Data System (ADS)

Hamalainen, Jari J.; Enwald, Petri

1994-11-01

The reliability of stand-alone machines and larger production units can be improved by automated condition monitoring. Analysis of wear particles in lubricating or hydraulic oils helps diagnosing the wear states of machine parts. This paper presents a computer vision system for automated classification of wear particles. Digitized images from experiments with a bearing test bench, a hydraulic system with an industrial company, and oil samples from different industrial sources were used for algorithm development and testing. The wear particles were divided into four classes indicating different wear mechanisms: cutting wear, fatigue wear, adhesive wear, and abrasive wear. The results showed that the fuzzy K-nearest neighbor classifier utilized gave the same distribution of wear particles as the classification by a human expert.

Fate of bromine in pyrolysis of printed circuit board wastes.

PubMed

Chien, Y C; Wang, H P; Lin, K S; Huang, Y J; Yang, Y W

2000-02-01

Behavior of Br in pyrolysis of the printed circuit board waste with valuable copper and oil recycling has been studied in the present work. Experimentally, pyrolysis of the printed circuit board waste generated approximately 40.6% of oils, 24.9% of noncondensible gases and 34.5% of solid residues that enriched in copper (90-95%). The cuts of the oils produced from pyrolysis of the printed circuit board waste into weighted boiling fraction were primarily light naphtha and heavy gas oil. Approximately 72.3% of total Br in the printed circuit board waste were found in product gas mainly as HBr and bromobenzene. However, by extended X-ray absorption fine structural (EXAFS) spectroscopy, Cu-O and Cu-(O)-Cu species with bond distance of 1.87 and 2.95 A, respectively, were observed in the solid residues. Essentially, no Cu-Br species was found.

Studies of pre-Selma Cretaceous core samples from the outcrop area in western Alabama

USGS Publications Warehouse

Monroe, Watson Hiner; Bergenback, Richard E.; Sohl, Norman F.; Applin, Esther R.; Leopold, Estella B.; Pakiser, Helen M.; Conant, Louis C.

1964-01-01

Quarter-cuts of the cores belonging to the U.S. National Museum have been deposited on indefinite loan with the Alabama Geological Survey at University, Ala., and with the Shell Oil Co. at Jackson, Miss. They are available there for inspection and study.

Decade of War: Applying Past Lessons to the Counter-ISIS Campaign

DTIC Science & Technology

2017-05-22

coalition partners to fight ISIS and its affiliates; (E) mechanisms to cut off or seize ISIS’s financial support, including financial transfers, money ... laundering , oil revenue, human trafficking, sales of looted art and historical artifacts, and other revenue sources; and (F) a detailed strategy to

CFD modelling of liquid-solid transport in the horizontal eccentric annuli

NASA Astrophysics Data System (ADS)

Sayindla, Sneha; Challabotla, Niranjan Reddy

2017-11-01

In oil and gas drilling operations, different types of drilling fluids are used to transport the solid cuttings in an annulus between drill pipe and well casing. The inner pipe is often eccentric and flow inside the annulus can be laminar or turbulent regime. In the present work, Eulerian-Eulerian granular multiphase CFD model is developed to systematically investigate the effect of the rheology of the drilling fluid type (Newtonian and non-Newtonian), drill pipe eccentricity and inner pipe rotation on the efficiency of cuttings transport. Both laminar and turbulent flow regimes were considered. Frictional pressure drop is computed and compared with the flow loop experimental results reported in the literature. The results confirm that the annular frictional pressure loss in a fully eccentric annulus are significantly lesser than the concentric annulus. Inner pipe rotation improve the efficiency of the cuttings transport in laminar flow regime. Cuttings transport velocity and concentration distribution were analysed to predict the different flow patterns such as stationary bed, moving bed, heterogeneous and homogeneous bed formation.

Browning control of fresh-cut lettuce by phytoncide treatment.

PubMed

Kim, Do-Hee; Kim, Han-Bit; Chung, Hun-Sik; Moon, Kwang-Deog

2014-09-15

Phytoncide essential oil derived from pine leaves was applied for the control of enzymatic browning of fresh-cut lettuce. Changes in the browning characteristics of cut lettuce treated with phytoncide in an water or ethanol solution (1%, v/v) at 10°C were investigated for 12days at 4°C. Other samples dipped in distilled water or 95% ethanol were used as the controls. The samples treated with phytoncide in an ethanol solution showed significantly higher L* values and lower a* values, ΔE values, browning index, phenolic compounds, and enzyme activities (PPO, POD, PAL) related to browning. The samples dipped in distilled water showed the opposite tendency. On the basis of changes in the browning characteristics, anti-browning effects of each treatment, phytoncide in an ethanol solution was the most effective treatment applied. These results suggest that phytoncide treatment could be used as an effective method for controlling enzymatic browning in fresh-cut lettuce. Copyright © 2014 Elsevier Ltd. All rights reserved.

Beneficial Use of Drilling Waste - A Wetland Restoration Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pioneer Natural Resources

2000-08-14

This project demonstrated that treated drill cuttings derived from oil and gas operations could be used as source material for rebuilding eroding wetlands in Louisiana. Planning to supply a restoration site, drill a source well, and provide part of the funding. Scientists from southeastern Louisiana University's (SLU) Wetland Biology Department were contracted to conduct the proposed field research and to perform mesocosm studies on the SLU campus. Plans were to use and abandoned open water drill slip as a restoration site. Dredged material was to be used to create berms to form an isolated cell that would then be filledmore » with a blend of dredged material and drill cuttings. Three elevations were used to test the substrates ability to support various alternative types of marsh vegetation, i.e., submergent, emergent, and upland. The drill cuttings were not raw cuttings, but were treated by either a dewatering process (performed by Cameron, Inc.) or by a stabilization process to encapsulate undesirable constituents (performed by SWACO, Division of Smith International).« less

A systematic review on nanoencapsulation of food bioactive ingredients and nutraceuticals by various nanocarriers.

PubMed

Assadpour, Elham; Jafari, Seid Mahdi

2018-06-08

Today, there is an ever-growing interest on natural food ingredients both by consumers and producers in the food industry. In fact, people are looking for those products in the market which are free from artificial and synthetic additives and can promote their health. These food bioactive ingredients should be formulated in such a way that protects them against harsh process and environmental conditions and safely could be delivered to the target organs and cells. Nanoencapsulation is a perfect strategy for this situation and there have been many studies in recent years for nanoencapsulation of food components and nutraceuticals by different technologies. In this review paper, our main goal is firstly to have an overview of nanoencapsulation techniques applicable to food ingredients in a systematic classification, i.e., lipid-based nanocarriers, nature-inspired nanocarriers, special-equipment-based nanocarriers, biopolymer nanocarriers, and other miscellaneous nanocarriers. Then, application of these cutting-edge nanocarriers for different nutraceuticals including phenolic compounds and antioxidants, natural food colorants, antimicrobial agents and essential oils, vitamins, minerals, flavors, fish oils and essential fatty acids will be discussed along with presenting some examples in each field.

Feasibility of real-time geochemical analysis using LIBS (Laser-Induced Breakdown Spectroscopy) in oil wells

NASA Astrophysics Data System (ADS)

Shahin, Mohamed

2014-05-01

The oil and gas industry has attempted for many years to find new ways to analyze and determine the type of rocks drilled on a real time basis. Mud analysis logging is a direct method of detecting oil and gas in formations drilled, it depends on the "feel" of the bit to decide formation type, as well as, geochemical analysis which was introduced 30 years ago, starting with a pulsed-neutron generator (PNG) based wireline tool upon which LWD technology was based. In this paper, we are studying the feasibility of introducing a new technology for real-time geochemical analysis. Laser-induced breakdown spectroscopy (LIBS) is a type of atomic emission spectroscopy, It is a cutting-edge technology that is used for many applications such as determination of alloy composition, origin of manufacture (by monitoring trace components), and molecular analysis (unknown identification). LIBS can analyze any material regardless of its state (solid, liquid or gas), based upon that fact, we can analyze rocks, formation fluids' types and contacts between them. In cooperation with the National Institute of Laser Enhanced Science, Cairo University in Egypt, we've done tests on sandstone, limestone and coal samples acquired from different places using Nd: YAG Laser with in addition to other components that are explained in details through this paper to understand the ability of Laser to analyze rock samples and provide their elemental composition using LIBS technique. We've got promising results from the sample analysis via LIBS and discussed the possibility of deploying this technology in oilfields suggesting many applications and giving a base for achieving a quantitative elemental analysis method in view of its shortcomings and solutions.

Ultrathin cellulose nanosheet membranes for superfast separation of oil-in-water nanoemulsions

NASA Astrophysics Data System (ADS)

Zhou, Ke; Zhang, Qiu Gen; Li, Hong Mei; Guo, Nan Nan; Zhu, Ai Mei; Liu, Qing Lin

2014-08-01

Oily wastewater is generated in diverse industrial processes, and its treatment has become crucial due to increasing environmental concerns. Herein, novel ultrathin nanoporous membranes of cellulose nanosheets have been fabricated for separation of oil-in-water nanoemulsions. The fabrication approach is facile and environmentally friendly, in which cellulose nanosheets are prepared by freeze-extraction of a very dilute cellulose solution. The as-prepared membranes have a cellulose nanosheet layer with a cut-off of 10-12 nm and a controllable thickness of 80-220 nm. They allow ultrafast water permeation and exhibit excellent size-selective separation properties. A 112 nm-thick membrane has a water flux of 1620 l m-2 h-1 bar-1 and a ferritin rejection of 92.5%. These membranes have been applied to remove oil from its aqueous nanoemulsions successfully, and they show an ultrafast and effective separation of oil-in-water nanoemulsions. The newly developed ultrathin cellulose membranes have a wide application in oily wastewater treatment, separation and purification of nanomaterials.Oily wastewater is generated in diverse industrial processes, and its treatment has become crucial due to increasing environmental concerns. Herein, novel ultrathin nanoporous membranes of cellulose nanosheets have been fabricated for separation of oil-in-water nanoemulsions. The fabrication approach is facile and environmentally friendly, in which cellulose nanosheets are prepared by freeze-extraction of a very dilute cellulose solution. The as-prepared membranes have a cellulose nanosheet layer with a cut-off of 10-12 nm and a controllable thickness of 80-220 nm. They allow ultrafast water permeation and exhibit excellent size-selective separation properties. A 112 nm-thick membrane has a water flux of 1620 l m-2 h-1 bar-1 and a ferritin rejection of 92.5%. These membranes have been applied to remove oil from its aqueous nanoemulsions successfully, and they show an ultrafast and effective separation of oil-in-water nanoemulsions. The newly developed ultrathin cellulose membranes have a wide application in oily wastewater treatment, separation and purification of nanomaterials. Electronic supplementary information (ESI) available: Stability of cyclohexane-in-water nanoemulsion at room temperature; analysis of the oil concentration in the permeate using GC; SEM images of the cellulose nanosheet membranes with different thicknesses. See DOI: 10.1039/c4nr03227f

Quantifying Above‐ and Below‐ground Growth Responses of the Western Australian Oil Mallee, Eucalyptus kochii subsp. plenissima, to Contrasting Decapitation Regimes

PubMed Central

WILDY, DAN T.; PATE, JOHN S.

2002-01-01

Resprouting in the oil mallee, Eucalyptus kochii Maiden & Blakely subsp. plenissima Gardner (Brooker), involves generation of new shoots from preformed meristematic foci on the lignotuber. Numbers of such foci escalated from 200 per lignotuber in trees aged 1 year to 3000 on 4‐ to 5‐year‐old trees. Removal of shoot biomass by decapitation 5 cm above ground in summer (February) or spring (October) resulted in initiation of 140–170 new shoots, but approx. 400 shoots were induced to form if crops of new shoots were successively removed until sprouting ceased and rootstocks senesced. Initially, the new shoot biomass of regenerating coppices increased slowly and the root biomass failed to increase appreciably until 1·7–2·5 years after cutting. Newly cut trees showed loss of fine root biomass, and structural roots failed to secondarily thicken to the extent shown by uncut trees. After 2 years, the biomass of shoots of coppiced plants was only one‐third that of uncut control trees and shoot : root dry mass ratios of coppiced plants were still low (1·5–2·0) compared with those of the controls (average ratio of 3·1). Spring cutting promoted quicker and greater biomass recovery than summer cutting. Starch in below‐ground biomass fell quickly following decapitation and remained low for a 12–18 month period. Utilization of starch reserves in naturally regenerating coppices was estimated to provide only a small proportion of the dry matter accumulated in new shoots. Results are discussed in relation to their impact on coppicing ability of the species under natural conditions or when successively coppiced for shoot biomass production. PMID:12197516

Quantifying above- and below-ground growth responses of the western Australian oil mallee, Eucalyptus kochii subsp. plenissima, to contrasting decapitation regimes.

PubMed

Wildy, Dan T; Pate, John S

2002-08-01

Resprouting in the oil mallee, Eucalyptus kochii Maiden & Blakely subsp. plenissima Gardner (Brooker), involves generation of new shoots from preformed meristematic foci on the lignotuber. Numbers of such foci escalated from 200 per lignotuber in trees aged 1 year to 3,000 on 4- to 5-year-old trees. Removal of shoot biomass by decapitation 5 cm above ground in summer (February) or spring (October) resulted in initiation of 140-170 new shoots, but approx. 400 shoots were induced to form if crops of new shoots were successively removed until sprouting ceased and rootstocks senesced. Initially, the new shoot biomass of regenerating coppices increased slowly and the root biomass failed to increase appreciably until 1.7-2.5 years after cutting. Newly cut trees showed loss of fine root biomass, and structural roots failed to secondarily thicken to the extent shown by uncut trees. After 2 years, the biomass of shoots of coppiced plants was only one-third that of uncut control trees and shoot:root dry mass ratios of coppiced plants were still low (1.5-2.0) compared with those of the controls (average ratio of 3.1). Spring cutting promoted quicker and greater biomass recovery than summer cutting. Starch in below-ground biomass fell quickly following decapitation and remained low for a 12-18 month period. Utilization of starch reserves in naturally regenerating coppices was estimated to provide only a small proportion of the dry matter accumulated in new shoots. Results are discussed in relation to their impact on coppicing ability of the species under natural conditions or when successively coppiced for shoot biomass production.

Combined effects of high pressure processing and addition of soy sauce and olive oil on safety and quality characteristics of chicken breast meat.

PubMed

Kruk, Zbigniew A; Kim, Hyun Joo; Kim, Yun Ji; Rutley, David L; Jung, Samooel; Lee, Soo Kee; Jo, Cheorun

2014-02-01

This study was conducted to evaluate the combined effect of high pressure (HP) with the addition of soy sauce and/or olive oil on the quality and safety of chicken breast meats. Samples were cut into 100 g pieces and 10% (w/w) of soy sauce (SS), 10% (w/w) of olive oil (OO), and a mixture of both 5% of soy sauce and 5% olive oil (w/w) (SO) were pressurized into meat with high pressure at 300 or 600 MPa. Cooking loss was lower in OO samples than SS samples. With increased pressure to 600 MPa, the oleic acid content of OO samples increased. The total unsaturated fatty acids were the highest in SO and OO 600 MPa samples. Lipid oxidation was retarded by addition of olive oil combined with HP. The addition of olive oil and soy sauce followed by HP decreased the amount of volatile basic nitrogen during storage and reduced the population of pathogens. Sensory evaluation indicated that the addition of olive oil enhanced the overall acceptance and willingness to buy. In conclusion, the combination of HP with the addition of soy sauce and/or olive oil is an effective technology that can improve chemical, health, sensory qualities and safety of chicken breast.

One of possible variants of the organization for recycling lubricate cooling of technological means for small businesses

NASA Astrophysics Data System (ADS)

Rusica, I.; Toca, A.; Stingaci, I.; Scaticailov, S.; Scaticailov, I.; Marinescu, O.; Kosenko, P.

2016-11-01

In the paper we analyze the application lubricate cooling technological environment in the processing of various materials in the past century greatly have increased cutting speed and respectively, has increased productivity [1]. Today, none of production in which anyway is used metal cutting machines of all types (milling, turning, grinding, drilling, etc.) is not without lubricant cooling technological liquid which in turn are designed to reduce cutting force and the load on metal cutting machine tools and machined parts in order to increase durability machine tools and reduce errors of processing details and also in resource energy saving. When using lubricate cooling technological environment reduces the temperature in the cutting zone resulting in higher tool life and the preservation of the surface structure being treated reducing wear of metal parts of the machine. Typically, lubricant cooling process fluids is used without replacing as long as possible not yet beginning to negatively affect the quality of process. However life expectancy lubricate cooling technological environment is limited. According to existing normative acts every kind of lubricate cooling technological environment through certain time must be deleted by from the system and subjected to a recycling. Lubricate cooling technological environment must be disposed of for the following reasons: occurs the microbial and the mechanical pollution cutting fluid, free oil impairs operational characteristics cutting fluid and increases consumption.

Advances in multiphase flow measurements using magnetic resonance relaxometry

NASA Astrophysics Data System (ADS)

Kantzas, Apostolos; Kryuchkov, Sergey; Chandrasekaran, Blake

2009-02-01

When it comes to the measurement of bitumen and water content as they are produced from thermally exploited reservoirs (cyclic steam stimulation or steam assisted gravity drainage) most of the current tools that are available in the market fail. This was demonstrated previously when our group introduced the first concept of a magnetic resonance based water-cut meter. The use of magnetic resonance as a potential tool for fluid cut metering from thermally produced heavy oil and bitumen reservoirs is revisited. At first a review of the work to date is presented. Our recent approach in the tackling of this problem follows. A patented process is coupled with a patented pipe design that can be used inside a magnetic field and can capture fluids up to 260°C and 4.2MPa. The paper describes the technical advances to this goal and offers a first glimpse of field data from an actual thermal facility for bitumen production. The paper also addresses an approach for converting the current discrete measurement device into a continuous measurement system. Preliminary results for this new concept are also presented.

Nutritional value of traditional Italian meat-based dishes: influence of cooking methods and recipe formulation.

PubMed

D'Evoli, L; Salvatore, P; Lucarini, M; Nicoli, S; Aguzzi, A; Gabrielli, P; Lombardi-Boccia, G

2009-01-01

The present study provides a picture of the compositional figure and nutritive value of meat-based dishes typical of Italian culinary tradition. Recipes specific for a bovine meat cut (top-side) were selected among the most widespread ones in Italy: in pan, pizzaiola, cutlet, meat ball, and escalope. The total fat and cholesterol content varied depending on the ingredients utilized (extra-virgin olive oil, parmesan, egg). Meat-based dishes that utilized extra-virgin olive oil showed a significant reduction in palmitic and stearic acids and a parallel increase in oleic acid compared with raw meat; furthermore, the ratio among saturated fatty acids, monounsaturated fatty acids and polyunsaturated fatty acids shifted in favour of monounsaturated fatty acids. B vitamins were affected at different extent by heating; by contrast, vitamin E content increased because of the new sources of this vitamin, which masked losses due to heating. Ingredients (parmesan, discretionary salt) induced significant increases in the calcium and sodium concentrations compared with raw meat. The total iron content did not show marked differences in most of the meat-based dishes compared with raw meat; by contrast, losses in the heme-iron concentration were detected depending on the severity of heating treatments. Our findings suggest that heme iron, because of its important health aspects, might be a useful index of the nutritional quality of cooked meats.

Nuclear Weapons: Comprehensive Test Ban Treaty

DTIC Science & Technology

2006-10-11

at the Nevada Test Site in June 2006 but now postponed to 2007 at the earliest, would have used 700 tons of ammonium nitrate and fuel oil to produce...June 10, 2006. Parakilas, Jacob , “Congress Cuts CTBTO Funding,” Arms Control Today, December 2005: 25. CRS-26 Robbins, Carla Anne, “U.S. Weighs Whether

DEVELOPMENT OF A SAMPLING PROCEDURE FOR LARGE NITROGEN- AND SULFUR-BEARING AEROSOLS

EPA Science Inventory

A single-stage impactor was modified to utilize a removable TFE impaction surface mounted on the end of an annular denuder. hen used with a polycarbonate filter coated with silicone oil, its cut point was 2.5 um and bounce was <1% for 8-um particles. ignificant bounce occurred wi...

24 CFR 3280.605 - Joints and connections.

Code of Federal Regulations, 2013 CFR

2013-04-01

... of the fitting. Plastic pipe and copper tubing shall be inserted to the full depth of the solder cup..., cutting oil and foreign matter shall be removed. Pipe joint cement or thread lubricant shall be of... connected to a public water system, made with solder having not more than 0.2 percent lead. (4) Plastic pipe...

24 CFR 3280.605 - Joints and connections.

Code of Federal Regulations, 2012 CFR

2012-04-01

... of the fitting. Plastic pipe and copper tubing shall be inserted to the full depth of the solder cup..., cutting oil and foreign matter shall be removed. Pipe joint cement or thread lubricant shall be of... connected to a public water system, made with solder having not more than 0.2 percent lead. (4) Plastic pipe...

24 CFR 3280.605 - Joints and connections.

Code of Federal Regulations, 2014 CFR

2014-04-01

... assembled for tightness. Pipe threads shall be fully engaged with the threads of the fitting. Plastic pipe... standard. Pipe ends shall be reamed out to size of bore. All burrs, chips, cutting oil and foreign matter..., made with solder having not more than 0.2 percent lead. (4) Plastic pipe, fittings and joints. Plastic...

Ecuador: Political and Economic Situation and U.S. Relations

DTIC Science & Technology

2008-05-21

plastics are the leading U.S. exports to Ecuador, while oil, bananas , and shrimp account for the bulk of U.S. imports from Ecuador. Since joining the World...Ecuador’s export market, other goods, such as seafood and cut flowers , have benefitted from the program. The ATPA was reauthorized and expanded by the

Publications - GMC 132 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a . Kustatan River #1 well Authors: Edison, T.A. Publication Date: 1989 Publisher: Alaska Division of data of cuttings from the Shell Oil Co. Kustatan River #1 well: Alaska Division of Geological &

Vertical multiphase flow correlations for high production rates and large tubulars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aggour, M.A.; Al-Yousef, H.Y.; Al-Muraikhi, A.J.

1996-02-01

Numerous correlations exist for predicting pressure drop in vertical multiphase flow. These correlations, however, were all developed and tested under limited operating conditions that do not match the high production rates and large tubulars normally found in the Middle East fields. This paper presents a comprehensive evaluation of existing correlations and modifications of some correlations to determine and recommend the best correlation or correlations for various field conditions. More than 400 field data sets covering tubing sizes from 2 3/8 to 7 inches, oil rates up to 23,200 B/D, water cuts up to 95%, and gas/oil ratio (GOR) up tomore » 927 scf/STB were used in this study. Considering all data combined, the Beggs and Brill correlation provided the best pressure predictions. However, the Hagedorn and Brown correlation was better for water cuts above 80%, while the Hasan and Kabir model was better for total liquid rates above 20,000 B/D. The Aziz correlation was significantly improved when the Orkiszewski flow-pattern transition criteria were used.« less

Addressing oil price changes through business profitability in oil and gas industry in the United Kingdom.

PubMed

Vătavu, Sorana; Lobonț, Oana-Ramona; Para, Iulia; Pelin, Andrei

2018-01-01

In this paper, we investigate how crude oil price and volume traded affected the profitability of oil and gas companies in the United Kingdom (UK) since the financial crisis started in 2008. The study benefit from insights of the financial statements, to develop a model that focuses on how changes in oil price impact corporate performance. In order to observe the financial indicators that influence the performance, as well as the effects that changes in oil prices and demand of crude oil have on the profitability of oil and gas companies, we apply comparative regression analysis, including the generalised method of moments estimation technique for panel data set. The sample is consisting of 31 oil and gas companies in the UK, and the period analysed is 2006-2014. Results show that profitable oil and gas companies managed to face the drop in oil price and recover, characterized by significant cash flows and stock turnover, efficient use of assets, and high solvency rates. Although the oil price and volume traded do not significantly affect profitability and other financial ratios, if the oil price continues to decrease, it would permanently alter both the UK economy and oil and gas companies. In order to survive, companies make drastic cuts and defer essential investments, often at the long-term expense of asset performance. This study is important in a world where the energy consumption steadily grew over time. However, the renewable energy is cheaper and more environmentally friendly, and thus, countries where oil and gas industry is one of the most popular sectors face an economic decline. These results could be useful for investors, managers or decision makers, reclaiming strategic decisions in the current uncertain and volatile environment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muntini, Melania Suweni, E-mail: melania@physics.its.ac.id; Pramono, Yono Hadi; Yustiana

As the world’s oil reserves are dwindling, some researchers have been prompted to make a breakthrough to further improve the efficiency of exploration and production. One of the technologies used is heating the crude oil. This paper presents the modeling results of heat treatment on crude oil using microwave energy. Modeling is conducted by assuming that the diameter of the well is 11,16 cm, the heat source is applied on the surface of the well, and the cut-off frequency in the air and on crude oil are 1,56 GHz. and 0.91 GHz, respectively. The energy generated by the microwave radiation is converted intomore » heat energy which is absorbed by the crude oil. Consequently, this energy increases the temperature of crude oil through a heat transfer mechanism. The results obtained showed that the temperature of crude oil is about 200°C at a depth of 62.5cm, and at a distance of 3 cm from the center of the well. Temperature along the well follows an exponential function, which is from the center of the well in the direction radially outward from the cylinder axis. It has been observed that the temperature decreases as measured from the well surface along the cylinder.« less

Investigations on Surface Milling of Hardened AISI 4140 Steel with Pulse Jet MQL Applicator

NASA Astrophysics Data System (ADS)

Bashir, Mahmood Al; Mia, Mozammel; Dhar, Nikhil Ranjan

2018-06-01

In this article, an experimental investigation was performed in milling hardened AISI 4140 steel of hardness 40 HRC. The machining was performed in both dry and minimal quantity lubricant (MQL) conditions, as part of neat machining, to make a strong comparison of the undertaken machining environments. The MQL was impinged int the form of pulse jet, by using the specially developed pulse-jet-attachment, to ensure that the cutting fluid can be applied in different timed pulses and quantities at critical zones. The tool wear, cutting force and surface roughness were taken as the quality responses while cutting speed, table feed rate and flow rate of the pulse were considered as influential factors. The depth of cut was kept constant at 1.50 mm because of its less significant effects and the straight oil was adopted as cutting fluid in pulse-jet-MQL. The effects of different factors, on the quality responses, are analyzed using ANOVA. It is observed that MQL applicator system exhibits overall better performance when compared to dry milling by reducing surface roughness, cutting force and prolonging tool life but a flow rate of 150 ml/h has tremendous effects on the responses. This investigation and afterward results are expected to aid the industrial practitioner and researcher to adopt the pulse-MQL in high speed milling to prolong tool life, reduce tool wear, diminish cutting force generation and promote better surface finish.

Investigations on Surface Milling of Hardened AISI 4140 Steel with Pulse Jet MQL Applicator

NASA Astrophysics Data System (ADS)

Bashir, Mahmood Al; Mia, Mozammel; Dhar, Nikhil Ranjan

2016-06-01

In this article, an experimental investigation was performed in milling hardened AISI 4140 steel of hardness 40 HRC. The machining was performed in both dry and minimal quantity lubricant (MQL) conditions, as part of neat machining, to make a strong comparison of the undertaken machining environments. The MQL was impinged int the form of pulse jet, by using the specially developed pulse-jet-attachment, to ensure that the cutting fluid can be applied in different timed pulses and quantities at critical zones. The tool wear, cutting force and surface roughness were taken as the quality responses while cutting speed, table feed rate and flow rate of the pulse were considered as influential factors. The depth of cut was kept constant at 1.50 mm because of its less significant effects and the straight oil was adopted as cutting fluid in pulse-jet-MQL. The effects of different factors, on the quality responses, are analyzed using ANOVA. It is observed that MQL applicator system exhibits overall better performance when compared to dry milling by reducing surface roughness, cutting force and prolonging tool life but a flow rate of 150 ml/h has tremendous effects on the responses. This investigation and afterward results are expected to aid the industrial practitioner and researcher to adopt the pulse-MQL in high speed milling to prolong tool life, reduce tool wear, diminish cutting force generation and promote better surface finish.

Cross-cutting High Surface Area Graphene-based Frameworks with Controlled Pore Structure/Dopants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaillard, J.

The goal of this project is to enhance the performance of graphene-based materials by manufacturing specific 3D architectures. The materials have global applications regarding fuel cell catalysts, gas adsorbents, supercapacitor/battery electrodes, ion (e.g., actinide) capture, gas separation, oil adsorption, and catalysis. This research focuses on hydrogen storage for hydrogen fuel cell vehicles with a potential transformational impact on hydrogen adsorbents that exhibit high gravimetric and volumetric density, a clean energy application sought by the Department of Energy. The development of an adsorbent material would enable broad commercial opportunities in hydrogen-fueled vehicles, promote new advanced nanomanufacturing scale-up, and open other opportunitiesmore » at Savannah River National Laboratory to utilize a high surface area material that is robust, chemically stable, and radiation resistant.« less

Supplemental safflower oil affects the fatty acid profile, including conjugated linoleic acid, of lamb.

PubMed

Boles, J A; Kott, R W; Hatfield, P G; Bergman, J W; Flynn, C R

2005-09-01

The objective of this study was to determine whether increasing levels of dietary safflower oil would alter unsaturated fat (especially CLA) and tocopherol content of lamb, animal performance, carcass characteristics, or color stability of lamb muscle tissue. Targhee x Rambouillet wethers (n = 60) were assigned to one of three diets (four pens per treatment with five lambs per pen) in a completely random design. Diets were formulated with supplemental safflower oil at 0 (control), 3, or 6% (as-fed basis) of the diet. Diets containing approximately 80% concentrate and 20% roughage were formulated, on a DM basis, to be isocaloric and isonitrogenous and to meet or exceed NRC requirements for Ca, P, and other nutrients. A subsample of 12 wethers per treatment was selected based on average BW (54 kg) and slaughtered. Carcass data (LM area, fat thickness, and internal fat content) and wholesale cut weight (leg, loin, rack, shoulder, breast, and foreshank), along with fatty acid, tocopherol, and color analysis, were determined on each carcass. The LM and infraspinatus were sampled for fatty acid profile. Increasing safflower oil supplementation from 0 to 3 or 6% increased the proportion of linoleic acid in the diet from 49.93 to 55.32 to 62.38%, respectively, whereas the percentage of oleic acid decreased from 27.94 to 23.80 to 20.73%, respectively. The percentage of oil in the diet did not (P > or = 0.11) alter the growth and carcass characteristics of lambs, nor did it alter the tocopherol content or color stability of meat. Increasing levels of safflower oil in lamb diets decreased (P < 0.01) the weight percentage of oleic acid in the infraspinatus and LM, and increased linoleic acid (P < 0.01). Oil supplementation increased (P < 0.01) the weight percentage of various isomers of CLA in muscle, with the greatest change in the cis-9,trans-11 isomer. Supplementation of sheep diets with safflower oil, up to 6% of the diet, resulted in increasing levels of unsaturated fatty acids and CLA in the lean tissue, without adversely affecting growth performance, carcass characteristics, or color stability of lamb.

The Finite Element Analysis for a Mini-Conductance Probe in Horizontal Oil-Water Two-Phase Flow.

PubMed

Kong, Weihang; Kong, Lingfu; Li, Lei; Liu, Xingbin; Xie, Ronghua; Li, Jun; Tang, Haitao

2016-08-24

Oil-water two-phase flow is widespread in petroleum industry processes. The study of oil-water two-phase flow in horizontal pipes and the liquid holdup measurement of oil-water two-phase flow are of great importance for the optimization of the oil production process. This paper presents a novel sensor, i.e., a mini-conductance probe (MCP) for measuring pure-water phase conductivity of oil-water segregated flow in horizontal pipes. The MCP solves the difficult problem of obtaining the pure-water correction for water holdup measurements by using a ring-shaped conductivity water-cut meter (RSCWCM). Firstly, using the finite element method (FEM), the spatial sensitivity field of the MCP is investigated and the optimized MCP geometry structure is determined in terms of the characteristic parameters. Then, the responses of the MCP for the oil-water segregated flow are calculated, and it is found that the MCP has better stability and sensitivity to the variation of water-layer thickness in the condition of high water holdup and low flow velocity. Finally, the static experiments for the oil-water segregated flow were carried out and a novel calibration method for pure-water phase conductivity measurements was presented. The validity of the pure-water phase conductivity measurement with segregated flow in horizontal pipes was verified by experimental results.

Combined Effects of High Pressure Processing and Addition of Soy Sauce and Olive Oil on Safety and Quality Characteristics of Chicken Breast Meat

PubMed Central

Kruk, Zbigniew A.; Kim, Hyun Joo; Kim, Yun Ji; Rutley, David L.; Jung, Samooel; Lee, Soo Kee; Jo, Cheorun

2014-01-01

This study was conducted to evaluate the combined effect of high pressure (HP) with the addition of soy sauce and/or olive oil on the quality and safety of chicken breast meats. Samples were cut into 100 g pieces and 10% (w/w) of soy sauce (SS), 10% (w/w) of olive oil (OO), and a mixture of both 5% of soy sauce and 5% olive oil (w/w) (SO) were pressurized into meat with high pressure at 300 or 600 MPa. Cooking loss was lower in OO samples than SS samples. With increased pressure to 600 MPa, the oleic acid content of OO samples increased. The total unsaturated fatty acids were the highest in SO and OO 600 MPa samples. Lipid oxidation was retarded by addition of olive oil combined with HP. The addition of olive oil and soy sauce followed by HP decreased the amount of volatile basic nitrogen during storage and reduced the population of pathogens. Sensory evaluation indicated that the addition of olive oil enhanced the overall acceptance and willingness to buy. In conclusion, the combination of HP with the addition of soy sauce and/or olive oil is an effective technology that can improve chemical, health, sensory qualities and safety of chicken breast. PMID:25049950

Improving performance of electrostatic heater-theaters for light crude doped heavy crude; A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharya, A.; Ray, S.; Rai, R.

1995-12-31

Crude oil treatment systems for heavy oil assume paramount importance due to the difficult nature of emulsions formed and presence of water in the form of small droplets. With the aging of heavy oil fields, operating under active water drive, water content in the emulsion produced increases substantially. This has a direct impact on heater-treater performance and treated crude quality. A typical problem is discussed in this paper where the gradual increase in emulsion production over a period of time in heavy oil belts of ONGC have affected the electrostatic heater-treater performance, treating light crude doped heavy crude, resulting inmore » increased BS&W (basic sediments and water) in the treated crude. Critical levels of water cut in both heavy and light crudes have been identified beyond which the existing emulsion treating system becomes ineffective. Analysis have also been carried out to identify optimum mixing proportion which result in the most effective demulsification.« less

Indian oil company joins efforts to reduce methane emissions

NASA Astrophysics Data System (ADS)

Kumar, Mohi

The Oil and Natural Gas Corp, Ltd. (ONGC), headquartered in Dehradun, India, has joined seven U.S. and Canadian oil and natural gas companies as a partner in a U.S. Environmental Protection Agency program to reduce greenhouse gas emissions. EPA's Natural Gas STAR International Program aims to reduce methane emissions from the oil and natural gas sector while delivering more gas to markets around the world. With this partnership, ONGC agrees to implement emissions reduction practices and to submit annual reports on progress achieved; EPA agrees to assist ONGC with training technicians in new cost-effective technologies that will help achieve target emissions. The Natural Gas STAR International Program is administered under the Methane to Markets Partnership, a group of 20 countries and 600 companies across the globe that since 2004 has volunteered to cut methane emissions. More information on EPA's agreement with ONGC can be found at http://www.epa.gov/gasstar/index.htm; information about the Methane to Markets Partnership can be found at http://www.methanetomarkets.org.

How to recover more value from small pine trees: Essential oils and resins

Treesearch

Vasant M. Kelkar; Brian W. Geils; Dennis R. Becker; Steven T. Overby; Daniel G. Neary

2006-01-01

In recent years, the young dense forests of northern Arizona have suffered extreme droughts, wildfires, and insect outbreaks. Improving forest health requires reducing forest density by cutting many small-diameter trees with the consequent production of large volumes of residual biomass. To offset the cost of handling this low-value timber, additional marketing options...

Publications - GMC 118 | Alaska Division of Geological & Geophysical

Science.gov Websites

and Facilities Staff Seismic and Well Data Data Reports Contact Us Frequently Asked Questions Ask a Company OCS Y-0849-2 (Hammerhead #2) well Authors: Unknown Publication Date: 1989 Publisher: Alaska reflectance data of cuttings from the Union Oil Company OCS Y-0849-2 (Hammerhead #2) well: Alaska Division of

46 CFR 160.043-4 - Construction and workmanship.

Code of Federal Regulations, 2011 CFR

2011-10-01

... shall have a common nail nick on one side. Before assembling, the sides of the tang shall be uniformly... formed to obtain a smooth cutting action. It shall have a common nail nick on one side, and the extreme... buffed, and the metal parts polished uniformly. The working parts shall be cleaned and oiled with a good...

46 CFR 160.043-4 - Construction and workmanship.

Code of Federal Regulations, 2010 CFR

2010-10-01

... shall have a common nail nick on one side. Before assembling, the sides of the tang shall be uniformly... formed to obtain a smooth cutting action. It shall have a common nail nick on one side, and the extreme... buffed, and the metal parts polished uniformly. The working parts shall be cleaned and oiled with a good...

The N.A.C.A. Photographic Apparatus for Studying Fuel Sprays from Oil Engine Injection Valves and Test Results from Several Researches

NASA Technical Reports Server (NTRS)

Beardsley, Edward G

1928-01-01

Apparatus for recording photographically the start, growth, and cut-off of oil sprays from injection valves has been developed at the Langley Memorial Aeronautical Laboratory. The apparatus consists of a high-tension transformer by means of which a bank of condensers is charged to a high voltage. The controlled discharge of these condensers in sequence, at a rate of several thousand per second, produces electric sparks of sufficient intensity to illuminate the moving spray for photographing. The sprays are injected from various types of valves into a chamber containing gases at pressures up to 600 pounds per square inch. Several series of pictures are shown. The results give the effects of injection pressure, chamber pressure, specific gravity of the fuel oil used, and injection-valve design, upon spray characteristics.

Volatile constituents of Pinus roxburghii from Nepal.

PubMed

Satyal, Prabodh; Paudel, Prajwal; Raut, Josna; Deo, Akash; Dosoky, Noura S; Setzer, William N

2013-01-01

Pinus roxburghii Sarg. Is one of 3 species of pine found in Nepal, the oil of which is traditionally used to treat cuts, wounds, boils, and blisters. To obtain, analyze, and examine the anti-microbial and cytotoxic activities of the essential oils of P. roxburghii. Three plant parts (cone, needle, and bark) of Pinus roxburghii were collected in Biratnagar, Nepal. The essential oils were obtained by hydrodistillation, and the chemical compositions were determined by GC-MS. The needle and cone essential oils were screened for anti-microbial activity against Bacillus cereus, Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, and Aspergillus niger; brine shrimp (Artemia salina) lethality; and in-vitro cytotoxicity against MCF-7 cells. GC-MS analysis for the cone oil revealed 81 compounds with 78 components being identified (95.5% of the oil) while 98.3% of needle oil was identified to contain 68 components and 98.6% of the bark oil (38 components) was identified. The 3 essential oils were dominated by sesquiterpenes, particularly (E)-caryophyllene (26.8%-34.5%) and α-humulene (5.0%-7.3%) as well as monoterpene alcohols terpinen-4-ol (4.1%-30.1%) and α-terpineol(2.8%-5.0%). The monoterpene δ-3-carene was present only in needle and cone essential oils (2.3% and 6.8%, respectively). Bio-activity assays of the cone essential oil of P. roxburghii showed remarkable cytotoxic activity (100% killing of MCF-7 cells at 100 μg/mL) along with notable brine shrimp lethality (LC50 =11.8 μg/mL). The cone essential oil did not show anti-bacterial activity, but it did exhibit anti-fungal activity against Aspergillus niger (MIC=39 μg/mL). The bioactivity of P. roxburghii essential oil is consistent with its traditional medicinal use.

Membrane technology for treating of waste nanofluids coolant: A review

NASA Astrophysics Data System (ADS)

Mohruni, Amrifan Saladin; Yuliwati, Erna; Sharif, Safian; Ismail, Ahmad Fauzi

2017-09-01

The treatment of cutting fluids wastes concerns a big number of industries, especially from the machining operations to foster environmental sustainability. Discharging cutting fluids, waste through separation technique could protect the environment and also human health in general. Several methods for the separation emulsified oils or oily wastewater have been proposed as three common methods, namely chemical, physicochemical and mechanical and membrane technology application. Membranes are used into separate and concentrate the pollutants in oily wastewater through its perm-selectivity. Meanwhile, the desire to compensate for the shortcomings of the cutting fluid media in a metal cutting operation led to introduce the using of nanofluids (NFs) in the minimum quantity lubricant (MQL) technique. NFs are prepared based on nanofluids technology by dispersing nanoparticles (NPs) in liquids. These fluids have potentially played to enhance the performance of traditional heat transfer fluids. Few researchers have studied investigation of the physical-chemical, thermo-physical and heat transfer characteristics of NFs for heat transfer applications. The use of minimum quantity lubrication (MQL) technique by NFs application is developed in many metal cutting operations. MQL did not only serve as a better alternative to flood cooling during machining operation and also increases better-finished surface, reduces impact loads on the environment and fosters environmental sustainability. Waste coolant filtration from cutting tools using membrane was treated by the pretreated process, coagulation technique and membrane filtration. Nanomaterials are also applied to modify the membrane structure and morphology. Polyvinylidene fluoride (PVDF) is the better choice in coolant wastewater treatment due to its hydrophobicity. Using of polyamide nanofiltration membranes BM-20D and UF-PS-100-100, 000, it resulted in the increase of permeability of waste coolant filtration. Titanium dioxide is nanomaterials additive to modify the Nanopores of the surface membrane. Contact angle and average pore size were used in the investigation of the surface morphology of membranes. An adequate choice in modifying the membrane surface in waste coolant filtration may bring a promised alternative as a solution in waste coolant remediation.

Pipeliners beat designers across Panama's jungle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-05-27

Hard-driving pipeline crews are slashing a path down the steep slopes of the Andes range on Panama's Caribbean coast for the final leg of an 80-mile Pacific-Atlantic oil link that will reduce shipping times for North Slope crude to Gulf Coast refineries. When completed in late August, the trans-isthmus tube will be able to drain the Panama Canal of Alaskan oil, which currently must be pumped from large tankers to 65,000 ton ships before passage through the 50-mile cut. The 36 and 40-in.-dia pipe will connect an existing Northville oil transshipment terminal at Puerto Armuelles, near Costa Rica on themore » Pacific Coast, with a new 2.5-million-bbl storage area at Chiriqui Grande on the Caribbean coast. Two pumping stations, one at Puerto Armuelles and another at the base of the Serrania de Tabasara mountains, will lift the oil 4,000 ft over the Continental Divide. Gravity flows of 7 1/2 ft per second down the steep drop to the swamps along the Caribbean will feed three 833,000-bbl tanks being built on a hillside overlooking Chiriqui Bay. From there, two 36-in. lines will feed concrete-coated pipe sections trenched into the surf zone and placed on the muddy bottom for the remaining distance to two marine loading buoys over a mile offshore. The catenary anchor-leg mooring buoys are designed to handle tankers of up to 160,000 tons in 65 ft of water at maximum fill rates of 120,000 bbl per hour.« less

Black shale source rocks and oil generation in the Cambrian and Ordovician of the central Appalachian Basin, USA

USGS Publications Warehouse

Ryder, R.T.; Burruss, R.C.; Hatch, J.R.

1998-01-01

Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician blcak shale (Utica and Antes shales) in the Appalachian basin. Moroever, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in the same source rocks. Oils from the Cambrian and Ordovician reservoirs have similar saturated hydrocarbon compositions, biomarker distributions, and carbon isotope signatures. Regional variations in the oils are attributed to differences in thermal maturation rather than to differences in source. Total organic carbon content, genetic potential, regional extent, and bitument extract geochemistry identify the balck shale of the Utica and Antes shales as the most plausible source of the oils. Other Cambrian and Ordovician shale and carbonate units, such as the Wells Creek formation, which rests on the Knox unconformity, and the Rome Formation and Conasauga Group in the Rome trough, are considered to be only local petroleum sources. Tmax, CAI, and pyrolysis yields from drill-hole cuttings and core indicate that the Utica Shale in eastern and central Ohio is mature with respect to oil generation. Burial, thermal, and hydrocarbon-generation history models suggest that much of the oil was generated from the Utica-Antes source in the late Paleozoic during the Alleghanian orogeny. A pervasive fracture network controlled by basement tectonics aided in the distribution of oil from the source to the trap. This fracture network permitted oil to move laterally and stratigraphically downsection through eastward-dipping, impermeable carbonate sequences to carrier zones such as the Middle Ordovician Knox unconformity, and to reservoirs such as porous dolomite in the Middle Ordovician Trenton Limestone in the Lima-Indiana field. Some of the oil and gas from the Utica-Antes source escaped vertically through a partially fractured, leaky Upper Ordovician shale seal into widespread Lower Silurian sandstone reservoirs.Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician black shale (Utica and Antes shales) in the Appalachian basin. Moreover, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in these same source rocks.

Comparison of tool life and surface roughness with MQL, flood cooling, and dry cutting conditions with P20 and D2 steel

NASA Astrophysics Data System (ADS)

Senevirathne, S. W. M. A. I.; Punchihewa, H. K. G.

2017-09-01

Minimum quantity lubrication (MQL) is a cutting fluid (CF) application method that has given promising results in improving machining performances. It has shown that, the performance of cutting systems, depends on the work and tool materials used. AISI P20, and D2 are popular in tool making industry. However, the applicability of MQL in machining these two steels has not been studied previously. This experimental study is focused on evaluating performances of MQL compared to dry cutting, and conventional flood cooling method. Trials were carried out with P20, and D2 steels, using coated carbides as tool material, emulsion cutting oil as the CF. Tool nose wear, and arithmetic average surface roughness (Ra) were taken as response variables. Results were statistically analysed for differences in response variables. Although many past literature has suggested that MQL causes improvements in tool wear, and surface finish, this study has found contradicting results. MQL has caused nearly 200% increase in tool nose wear, and nearly 11-13% increase in surface roughness compared flood cooling method with both P20 and D2. Therefore, this study concludes that MQL affects adversely in machining P20, and D2 steels.

Solvent cleaning of pole transformers containing PCB contaminated insulating oil.

PubMed

Kanbe, H; Shibuya, M

2001-01-01

In 1989, it was discovered that the recycled insulation oil in pole transformers for electric power supply was contaminated with trace amounts of polychlorinated biphenyls (PCBs; maximum 50 mg-PCB/kg-insulation oil). In order to remove the PCBs from transformer components using n-hexane as a solvent, we investigated the relationship between progressive stages of dismantling and cleaning results. The results are summarized as follows: (1) Based on the cleaning test results, we made an estimate of the residual PCB amount on iron and copper components. By dismantling the test pole transformers into the "iron core and coil portion" and cleaning the components, we achieved a residual PCB amount that was below the limit of detection (0.05 mg-PCB/kg-material). To achieve a residual PCB amount below the limit of detection for the transformer paper component, it was necessary to cut the paper into pieces smaller than 5 mm. We were unable to achieve a residual PCB amount below the limit of detection for the wood component. (2) Compared to Japan's stipulated limited concentration standard values for PCBs, the results of the cleaning test show that cleaning iron or copper components with PCBs only on their surface with the solvent n-hexane will satisfy the limited concentration standard values when care is taken to ensure the component surfaces have adequate contact with the cleaning solvent.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seyler, Beverly; Grube, John; Huff, Bryan

Within the Illinois Basin, most of the oilfields are mature and have been extensively waterflooded with water cuts that range up to 99% in many of the larger fields. In order to maximize production of significant remaining mobile oil from these fields, new recovery techniques need to be researched and applied. The purpose of this project was to conduct reservoir characterization studies supporting Alkaline-Surfactant-Polymer Floods in two distinct sandstone reservoirs in Lawrence Field, Lawrence County, Illinois. A project using alkaline-surfactantpolymer (ASP) has been established in the century old Lawrence Field in southeastern Illinois where original oil in place (OOIP) ismore » estimated at over a billion barrels and 400 million barrels have been recovered leaving more than 600 million barrels as an EOR target. Radial core flood analysis using core from the field demonstrated recoveries greater than 20% of OOIP. While the lab results are likely optimistic to actual field performance, the ASP tests indicate that substantial reserves could be recovered even if the field results are 5 to 10% of OOIP. Reservoir characterization is a key factor in the success of any EOR application. Reservoirs within the Illinois Basin are frequently characterized as being highly compartmentalized resulting in multiple flow unit configurations. The research conducted on Lawrence Field focused on characteristics that define reservoir compartmentalization in order to delineate preferred target areas so that the chemical flood can be designed and implemented for the greatest recovery potential. Along with traditional facies mapping, core analyses and petrographic analyses, conceptual geological models were constructed and used to develop 3D geocellular models, a valuable tool for visualizing reservoir architecture and also a prerequisite for reservoir simulation modeling. Cores were described and potential permeability barriers were correlated using geophysical logs. Petrographic analyses were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in Lawrence Field. Geologic and geocellular modeling needed for reservoir characterization and reservoir simulation were completed as prerequisites for design of efficient ASP flood patterns. Characterizing the complex reservoir geology that identifies the geologic conditions that will optimize oil recoveries for expansion of the ASP pilots in the Bridgeport and Cypress sandstones to other areas of Lawrence Field is the primary objective of this project. It will permit evaluation of efficiency of oil recovery from Bridgeport and Cypress sandstone reservoirs using ASP technology. Additionally evaluation of similar Pennsylvanian and Chesterian reservoirs shows that it is likely that ASP flood technology can be successfully applied to similar reservoirs in the Illinois Basin as well as to other U.S. reservoirs. Chemical flooding was introduced in stages with the first flood initiated in 2010 and a second offset pilot project initiated during 2011. Rex Energy Corporation is reporting a positive response on its ASP Middagh pilot project in the Pennsylvanian Bridgeport B reservoir, Lawrence Field. Oil response in the 15 acre flood has continued to show an increase in oil cut from 1% to 12%. Total pattern production increased from 16 BOPD and stabilized at a range of 65-75 BOPD in the last three months of 2011. Peak production rose to 100 + BOPD. Oil cut in the pilot increased for 1.0% to ~ 12.0% with an individual well showing oil cuts greater than 20%. A second, 58 acre pilot (Perkins-Smith) adjacent to and likely in communication with the Middagh pilot has been initiated. Preliminary brine injection has been implemented and ASP injection was initiated in mid-2012. Response is expected by mid-2013 with peak recovery expected by late 2013. Rex Energy is projecting full scale expansion with the next step of development being a 351 acre project scheduled to begin in mid-2013. Preliminary development has been initiated in this Delta Unit area located in the south half of section 32, T4N, R12W.« less

Publications - GMC 406 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 406 Publication Details Title: Carbon isotope and total organic carbon (TOC) analysis of organic carbon (TOC) analysis of washed and unwashed cuttings from the South Barrow Test #3 well: Alaska Table(s) gmc406_toc.xls (196.0 K) gmc406_samples.xls (144.0 K) Keywords Isotopes; Oil and Gas; Organic

40 CFR Appendix 1 to Subpart D of... - Procedure for Determining When Coastal Cook Inlet Operators Qualify for an Exemption From the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Procedure for Determining When Coastal... SBF-Cuttings in Coastal Cook Inlet, Alaska 1 Appendix 1 to Subpart D of Part 435 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) OIL AND...

40 CFR Appendix 1 to Subpart D of... - Procedure for Determining When Coastal Cook Inlet Operators Qualify for an Exemption From the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Procedure for Determining When Coastal... SBF-Cuttings in Coastal Cook Inlet, Alaska 1 Appendix 1 to Subpart D of Part 435 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) OIL AND...

40 CFR Appendix 1 to Subpart D of... - Procedure for Determining When Coastal Cook Inlet Operators Qualify for an Exemption From the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Procedure for Determining When Coastal... SBF-Cuttings in Coastal Cook Inlet, Alaska 1 Appendix 1 to Subpart D of Part 435 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS...

40 CFR Appendix 1 to Subpart D of... - Procedure for Determining When Coastal Cook Inlet Operators Qualify for an Exemption From the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Procedure for Determining When Coastal... SBF-Cuttings in Coastal Cook Inlet, Alaska 1 Appendix 1 to Subpart D of Part 435 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS...

40 CFR Appendix 1 to Subpart D of... - Procedure for Determining When Coastal Cook Inlet Operators Qualify for an Exemption From the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Procedure for Determining When Coastal... SBF-Cuttings in Coastal Cook Inlet, Alaska 1 Appendix 1 to Subpart D of Part 435 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) OIL AND...

The Role of the Government in Perpetrating Genocide: A Comparative Analysis of 1994 Rwanda Genocide and 2003 Sudan Genocide

DTIC Science & Technology

2013-06-13

29 French Relations with Rwanda...Military and Economic FAR French acronym-Forces Armées Rwandaise FDLR French acronym- Forces Democratiques de Liberation du Rwanda HRW Human Rights...1999-2001, during Sudan’s oil boom, the government intensified bombings of civilians and cutting off their food supply in order to demoralize them

Sprouting of thinned hybrid poplars on bituminous strip-mine spoils in Pennsylvania

Treesearch

Walter H. Davidson; Grant Davis

1972-01-01

Various thinning techniques were applied to 5-year old hybrid poplar stands on bituminous strip-mine spoils. Basal and stump sprays of 2, 4, 5-T in diesel oil were effective for killing the trees. There was no evidence that chemical treatments affected adjacent trees. Where trees were cut and stumps were not chemically treated, all clones sprouted prolifically....

Energy Security of Army Installations & Islanding Methodologies

DTIC Science & Technology

2012-01-16

islanding of energy generation and distribution networks including electricity, natural gas , steam , liquid fuel, water, and others for the diverse...in geopolitics and war/peace/terrorism Breakthrough in reformation process of synthetic fuel production Hydrogen focused energy sector Oil and gas ...of synthetic AMf Q production Hydrogen focused energy sector D Of and gas remain available and cost-effective Natural Gas prices cut In

Experimental Investigation of Two-Phase Oil (D130)-Water Flow in 4″ Pipe for Different Inclination Angles

NASA Astrophysics Data System (ADS)

Shaahid, S. M.; Basha, Mehaboob; Al-Hems, Luai M.

2018-03-01

Oil and water are often produced and transported together in pipelines that have various degrees of inclination from the horizontal. The flow of two immiscible liquids oil and water in pipes has been a research topic since several decades. In oil and chemical industries, knowledge of the frictional pressure loss in oil-water flows in pipes is necessary to specify the size of the pump required to pump the emulsions. An experimental investigation has been carried out for measurement of pressure drop of oil (D130)-water two-phase flows in 4 inch diameter inclined stainless steel pipe at different flow conditions. Experiments were conducted for different inclination angles including; 0°, 15°, 30° (for water cuts “WC” 0 - 100%). The flow rates at the inlet were varied from 4000 to 8000 barrels-per-day (BPD). For a given flow rate the frictional pressure drop has been found to increase (for all angles) from WC = 0 - 60%, and thereafter friction pressure drop decreases, this could be due phase inversion. For a given WC 40%, the frictional pressure drop has been found to increase with angle and flow rate. It has been noticed that inclination angle has appreciable effect on frictional pressure drop.

Application of PLE for the determination of essential oil components from Thymus vulgaris L.

PubMed

Dawidowicz, Andrzej L; Rado, Ewelina; Wianowska, Dorota; Mardarowicz, Marek; Gawdzik, Jan

2008-08-15

Essential plants, due to their long presence in human history, their status in culinary arts, their use in medicine and perfume manufacture, belong to frequently examined stock materials in scientific and industrial laboratories. Because of a large number of freshly cut, dried or frozen plant samples requiring the determination of essential oil amount and composition, a fast, safe, simple, efficient and highly automatic sample preparation method is needed. Five sample preparation methods (steam distillation, extraction in the Soxhlet apparatus, supercritical fluid extraction, solid phase microextraction and pressurized liquid extraction) used for the isolation of aroma-active components from Thymus vulgaris L. are compared in the paper. The methods are mainly discussed with regard to the recovery of components which typically exist in essential oil isolated by steam distillation. According to the obtained data, PLE is the most efficient sample preparation method in determining the essential oil from the thyme herb. Although co-extraction of non-volatile ingredients is the main drawback of this method, it is characterized by the highest yield of essential oil components and the shortest extraction time required. Moreover, the relative peak amounts of essential components revealed by PLE are comparable with those obtained by steam distillation, which is recognized as standard sample preparation method for the analysis of essential oils in aromatic plants.

Gas chromatographic sulphur speciation in heavy crude oil using a modified standard D5623 method and microfluidic Deans switching.

PubMed

Heshka, Nicole E; Choy, Joanne M; Chen, Jinwen

2017-12-29

A modification to American Society for Testing and Materials (ASTM) method D5623 is proposed to enable successful and repeatable analysis of heavy crude oil samples. A two-dimensional gas chromatography configuration was implemented, with separation of sulphur compounds occurring on two columns. A Deans switch is used to enable heart-cutting of volatile sulphur compounds onto a DB-Sulfur stationary phase, and separation occurs concurrently with the backflushing of the primary column. The use of a sulphur-selective detector increases selectivity, and 22 volatile sulphur species are quantified in less than 15min, which is almost half the time of the original ASTM method. Samples ranging from light distillation cuts to whole crudes (boiling from 100°C to >750°C) were analyzed with minimal sample preparation. The calculated limit of detection was 0.7mg/kg, repeatability was 3% relative standard deviation (RSD), and a linear range of 1-250mg/kg was obtained, with an R 2 value of 0.994 or better, depending on the compound. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

PINCH WELD TESTING TO SUPPORT CHANGE IN MANUFACTURING OIL AT THE KCP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korinko, P; David Maxwell, D

2008-02-28

This task supports the change from an oil mixture termed 50:50 oil (an equal parts mixture of Milpro 634 and Pennex N47) to a new oil mixture (Castrol Illocut 334). This change was necessitated by a KCP vendor no longer supplying the Pennex N47 component of the 50-50. In order to continue production of machined parts, a detailed process was followed to ensure that high quality parts could be manufactured and that the cutting oil selected would provide acceptable human performance characteristics, e.g., skin irritability, smell, etc. A prime consideration in changing the oil was that no apparent change inmore » the pinch weldability of the fill stems fabricated using the new oil and process parameters, if any, be observed. A two part approach, as detailed in the plan shown in Appendix B, was used to qualify the effect of the process on pinch weld characteristics. In the first phase, ref. 1., the weld parameter window was defined using fill stems made from 304L, 21-6-9, and 316 stainless steel. These weld conditions were then subsequently used for the Castrol Illocut 334 machined fill stems. The results of this activity are reported in this document. A follow-on task of welding in the facility was requested by one of the design agencies and this will be completed and reported separately.« less

Effect of hydrocarbon to nuclear magnetic resonance (NMR) logging in tight sandstone reservoirs and method for hydrocarbon correction

NASA Astrophysics Data System (ADS)

Xiao, Liang; Mao, Zhi-qiang; Xie, Xiu-hong

2017-04-01

It is crucial to understand the behavior of the T2 distribution in the presence of hydrocarbon to properly interpret pore size distribution from NMR logging. The NMR T2 spectrum is associated with pore throat radius distribution under fully brine saturated. However, when the pore space occupied by hydrocarbon, the shape of NMR spectrum is changed due to the bulk relaxation of hydrocarbon. In this study, to understand the effect of hydrocarbon to NMR logging, the kerosene and transformer oil are used to simulate borehole crude oils with different viscosity. 20 core samples, which were separately drilled from conventional, medium porosity and permeability and tight sands are saturated with four conditions of irreducible water saturation, fully saturated with brine, hydrocarbon-bearing condition and residual oil saturation, and the corresponding NMR experiments are applied to acquire NMR measurements. The residual oil saturation is used to simulate field NMR logging due to the shallow investigation depth of NMR logging. The NMR spectra with these conditions are compared, the results illustrate that for core samples drilled from tight sandstone reservoirs, the shape of NMR spectra have much change once they pore space occupied by hydrocarbon. The T2 distributions are wide, and they are bimodal due to the effect of bulk relaxation of hydrocarbon, even though the NMR spectra are unimodal under fully brine saturated. The location of the first peaks are similar with those of the irreducible water, and the second peaks are close to the bulk relaxation of viscosity oils. While for core samples drilled from conventional formations, the shape of T2 spectra have little changes. The T2 distributions overlap with each other under these three conditions of fully brine saturated, hydrocarbon-bearing and residual oil. Hence, in tight sandstone reservoirs, the shape of NMR logging should be corrected. In this study, based on the lab experiments, seven T2 times of 1ms, 3ms, 10ms, 33ms, 100ms, 300ms and 1000ms are first used to separate the T2 distributions of the residual oil saturation as 8 parts, and 8 pore components percentage compositions are calculated, second, an optimal T2 cutoff is determined to cut the T2 spectra of fully brine saturated conditions into two parts, the left parts (with short T2 time) represent to the irreducible water, and they do not need to be corrected, only the shape for the right parts of the T2 spectra needed to be corrected. Third the relationships among the amplitudes corresponding to the T2 times large than the optimal T2 cut off and 8 pore components percentage compositions are established, and they are used to predict corrected T2 amplitudes from NMR logging under residual oil saturation. Finally, the amplitudes corresponding to the left parts and the estimated amplitudes are spliced as the corrected NMR amplitudes, and a corrected T2 spectrum can be obtained. The reliability of this method is verified by comparing the corrected results and the experimental measurements. This method is extended to field application, fully water saturated T2 distributions are extracted from field NMR logging, and they are used to precisely evaluate hydrocarbon-bearing formations pore structure.

National energy conservation

NASA Technical Reports Server (NTRS)

1975-01-01

A set of energy conservation actions that cut across all sectors of the economy were analyzed so that all actions under consideration be analyzed systematically and as a whole. The actions considered were as follows: (1) roll back the price of newly discovered oil, (2) freeze gasoline production for 3 years at 1972 levels, (3) mandate automobile mileage improvements, (4) require industry to improve energy efficiency, (5) require manufacture of household appliances with greater efficiency, (6) force conversion of many power plants from gas and oil to coal. The results showed that considerable gas and oil would be saved by forcing switches to coal. However, the large scale switch to coal was shown to require greatly increased outputs from many other industries that in turn require more energy. It was estimated that nearly 2.5 quads of additional coal were needed to produce these additional requirements. Also, the indirect requirements would create more jobs.

Hazard assessment of a simulated oil spill on intertidal areas of the St. Lawrence River with SPMD-TOX

USGS Publications Warehouse

Johnson, B. Thomas; Petty, J.D.; Huckins, J.N.; Lee, Kenneth; Gauthier, J.

2004-01-01

Phytoremediation in a simulated crude oil spill was studied with a “minimalistic” approach. The SPMD-TOX paradigm—a miniature passive sorptive device to collect and concentrate chemicals and microscale tests to detect toxicity—was used to monitor over time the bioavailability and potential toxicity of an oil spill. A simulated crude oil spill was initiated on an intertidal freshwater grass-wetland along the St. Lawrence River southwest of Quebec City, Quebec, Canada. Several phytoremediation treatments were investigated; to dissipate and ameliorate the spill, treatments included nutrient amendments with inorganic nitrogen sources (ammonium nitrate and sodium nitrate) and phosphate (super triple phosphate) with and without cut plants, with natural attenuation (no phytoremedial treatment) as a control. Sequestered oil residues were bioavailable in all oil-treated plots in Weeks 1 and 2. Interestingly, the samples were colored and fluoresced under ultraviolet light. In addition, microscale tests showed that sequestered residues were acutely toxic and genotoxic, as well as that they induced hepatic P450enzymes. Analysis of these data suggested that polycyclic aromatic hydrocarbons were among the bioavailable residues sequestered. In addition, these findings suggested that the toxic bioavailable fractions of the oil spill and degradation products dissipated rapidly over time because after the second week the water column contained no oil or detectable degradation products in this riverine intertidal wetland. SPMD-TOX revealed no evidence of bioavailable oil products in Weeks 4, 6, 8, and 12. All phytoremediation efforts appeared to be ineffective in changing either the dissipation rate or the ability to ameliorate the oil toxicity. SPMD-TOX analysis of the water columns from these riverine experimental plots profiled the occurrence, dissipation, and influence of phytoremediation on the bioavailability and toxicity of oil products (parent or degradation products).

Occurrence of high gravity oil in an Oligocene Vicksburg age sandstone in Jim Hogg County, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, L.W.; Hilton, N.

1980-01-01

On October 1, 1979 the Guardian Oil Co. E-1 Mestena oil and gas well was completed in an Oligocene, Vicksburg sandstone. The initial potential was 245 BOPD of 75 API gravity oil. A hydrocarbon analysis of a sample obtained from the E-1 well revealed an oil composed primarily of propane and butane with a significant portion of pentane to heptane range material which accounts for the exceptionally high gravity of the liquid hydrocarbons. This analysis further showed that the E-1 well is producing almost no methane, ethane, or other hydrocarbons of greater molecular weight than nonane. Several faults, adjacent tomore » the well, could have provided a path of migration for the hydrocarbons. A detailed analysis of the butane to heptane fluid produced by the E-1 well indicated the fluid contained a large amount of compounds characteristic of an immature crude. Coal fragments present in the cutting from a nearby well and the regional geology of the Vicksburg Formation suggest that one possible source for the hydrocarbons of the E-1 well could have been lipid rich Cannel-type coal.« less

Antimicrobial activity of essential oils of Physalis angulata. L.

PubMed

Osho, A; Adetunji, T; Fayemi, S O; Moronkola, D O

2010-01-01

The need for a reduction in drug resistance led to the investigation of Argemone Mexicana L. as an agent against Bacillus subtilis, Klebsiella pneumoniae, Staphylococcus aureus, Pseudomonas aeruginosa, Candida albicans, Candida stellatoidea and Candida torulopsis, using well diffusion and minimum inhibitory concentrations methods. The sensitivity of Bacillus Subtilis, Klebsiella pneumoniae, Pseudomonas aeruginosa and Staphylococcus aureus to the essential oils of both the aerial and root parts were determined. Pseudomonas aeruginosa was resistant to the essential oil from both the aerial and root part of the plant. C. torulopsis, C. stellatoidea and C. albicans were susceptible to the essential oils from the aerial and root part of the plant. The minimum inhibitory concentrations ranging between 3.75 mg/ml and 4.0 mg/ml were recorded for Bacillus subtilis, Klebsiella pneumoniae by the aerial and the root extracts, but P. aeruginosa and S. aureus were not susceptible to the aerial and root extracts. The observed inhibition of selected bacteria and fungi by oils of Physalis angulata makes it a promising antimicrobial agent. This study justifies its uses for treatment of sores, cuts, intestinal and digestive problems and some skin-diseases often reported in folkloric medicine.

Strontium isotopes as an indicator for groundwater salinity sources in the Kirkuk region, Iraq.

PubMed

Sahib, Layth Y; Marandi, Andres; Schüth, Christoph

2016-08-15

The Kirkuk region in northern Iraq hosts some of the largest oil fields in the Middle East. Several anticline structures enabled vertical migration and entrapment of the oil. Frequently, complex fracture systems and faults cut across the Eocene and middle Oligocene reservoirs and the cap rock, the Fatha Formation of Miocene age. Seepage of crude oil and oil field brines are therefore a common observation in the anticline axes and contamination of shallow groundwater resources is a major concern. In this study, 65 water samples were collected in the Kirkuk region to analyze and distinguish mixing processes between shallow groundwater resources, uprising oil field brines, and dissolution of gypsum and halite from the Fatha Formation. Hydrochemical analyses of the water samples included general hydrochemistry, stable water isotopes, as well as strontium concentrations and for 22 of the samples strontium isotopes ((87)Sr/(86)Sr). Strontium concentrations increased close to the anticline axes with highest concentrations in the oil field brines (300mg/l). Strontium isotopes proved to be a valuable tool to distinguish mixing processes as isotope signatures of the oil field brines and of waters from the Fatha Formation are significantly different. It could be shown, that mixing of shallow groundwater with oil field brines is occurring close to the major fault zones in the anticlines but high concentrations of strontium in the water samples are mainly due to dissolution from the Fatha Formation. Copyright © 2016 Elsevier B.V. All rights reserved.

Earth Observations

NASA Image and Video Library

2010-07-23

ISS024-E-009404 (23 July 2010) --- This photo taken from the International Space Station on July 23, 2010, shows the Gulf of Mexico oil spill as part of ongoing observations of the region. When this image was taken, three months after the explosion on the Deepwater Horizon oil rig, the leak had been plugged for eight days. Water surfaces appear bright and land surfaces appear dark in the image. The stark contrast is due to sun glint, in which the sun is reflected brilliantly off all water surfaces back towards the astronaut observer on board the station. The sun glint reveals various features in the Gulf of Mexico, especially sheens of oil as packets of long bright streaks seen on the left side of the image. Sediments carried by the Mississippi River have a light-yellow coloration in this image, with distinct margins between plumes that likely mark tidal pulses of river water into the Gulf of Mexico. A boat wake cuts across one of the oil packets at image lower left. Daily National Oceanic and Atmospheric Administration (NOAA) maps of oil distribution show predicted heavier and lighter oil movement near the Gulf coastline. The maps show that on the day this image was taken, the north edge of the ?oiled? zone was expected to bank up against the delta. The observed spread of the surface oil in the approximately 100 days since the explosion highlights the connectivity between the deepwater areas and coastlines of the Gulf of Mexico.

[Analysis of terpineol and improvement of technology process in terpineol production].

PubMed

Liang, Ming; Chen, Min; Cai, Chun-ping; Weng, Ruo-rong

2002-11-01

A method for the separation and determination of terpineol oil by temperature programming capillary gas chromatography has been established. An OV-1 fused silica capillary column (30 m x 0.32 mm i.d. x 0.25 microns) was used with a temperature increase rates of 1.5 degrees C/min from 70 degrees C to 100 degrees C, 5 degrees C/min from 100 degrees C to 160 degrees C, 10 degrees C/min from 160 degrees C to 220 degrees C and then hold for 2 min. The main chemical components and their relative contents of the terpineol oil, terpinene oil, red and yellow oils of middle oils in the terpineol production and natural terpineol were analyzed by capillary gas chromatography-Fourier transform infrared spectrometry (GC-FTIR) and gas chromatography-mass spectrometry (GC-MS). The typical chromatograms of these oils are given. It has offered the information of the boiling points of the chemical compounds, and it is helpful to reutilize them after their separation by rectification. The results showed that the main compounds of the heavy cut of terpineol were longifolene and beta-caryophyllene. They are from the raw material, terpinene oil. The main compounds in the natural terpineol oil were eucalyptol, trans-4-thujanol, p-isopropenyl toluene, cis-4-thujanol, linalool, camphor, borneol, 4-terpineol, alpha-terpineol and safrole. The contents of beta-terpineol and gamma-terpineol were not so high as in synthetic terpineol.

Occupation and bladder cancer: a death-certificate study.

PubMed Central

Dolin, P. J.; Cook-Mozaffari, P.

1992-01-01

Occupational statements on death certificates of 2,457 males aged 25-64 who died from bladder cancer in selected coastal and estaurine regions of England and Wales during 1965-1980 were studied. Excess mortality was found for deck and engine room crew of ships, railway workers, electrical and electronic workers, shoemakers and repairers, and tobacco workers. An excess of cases also occurred among food workers, particularly those employed in the bread and flour confectionary industry or involved in the extraction of animal and vegetable oils and fats. Use of a job-exposure matrix revealed elevated risk for occupations in which most workers were exposed to paints and pigments, benzene and cutting oils. PMID:1520596

Microfabricated Nickel Based Sensors for Hostile and High Pressure Environments

NASA Astrophysics Data System (ADS)

Holt, Christopher Michael Bjustrom

This thesis outlines the development of two platforms for integrating microfabricated sensors with high pressure feedthroughs for application in hostile high temperature high pressure environments. An application in oil well production logging is explored and two sensors were implemented with these platforms for application in an oil well. The first platform developed involved microfabrication directly onto a cut and polished high pressure feedthrough. This technique enables a system that is more robust than the wire bonded silicon die technique used for MEMS integration in pressure sensors. Removing wire bonds from the traditional MEMS package allows for direct interface of a microfabricated sensor with a hostile high pressure fluid environment which is not currently possible. During the development of this platform key performance metrics included pressure testing to 70MPa and temperature cycling from 20°C to 200°C. This platform enables electronics integration with a variety of microfabricated electrical and thermal based sensors which can be immersed within the oil well environment. The second platform enabled free space fabrication of nickel microfabricated devices onto an array of pins using a thick tin sacrificial layer. This technique allowed microfabrication of metal MEMS that are released by distances of 1cm from their substrate. This method is quite flexible and allows for fabrication to be done on any pin array substrate regardless of surface quality. Being able to place released MEMS sensors directly onto traditional style circuit boards, ceramic circuit boards, electrical connectors, ribbon cables, pin headers, or high pressure feedthroughs greatly improves the variety of possible applications and reduces fabrication costs. These two platforms were then used to fabricate thermal conductivity sensors that showed excellent performance for distinguishing between oil, water, and gas phases. Testing was conducted at various flow rates and performance of the released platform was shown to be better than the performance seen in the anchored sensors while both platforms were significantly better than a simply fabricated wrapped wire sensor. The anchored platform was also used to demonstrate a traditional capacitance based fluid dielectric sensor which was found to work similarly to conventional commercial capacitance probes while being significantly smaller in size.

Volatile constituents of Pinus roxburghii from Nepal

PubMed Central

Satyal, Prabodh; Paudel, Prajwal; Raut, Josna; Deo, Akash; Dosoky, Noura S.; Setzer, William N.

2013-01-01

Background: Pinus roxburghii Sarg. Is one of 3 species of pine found in Nepal, the oil of which is traditionally used to treat cuts, wounds, boils, and blisters. Objective: To obtain, analyze, and examine the anti-microbial and cytotoxic activities of the essential oils of P. roxburghii. Materials and Methods: Three plant parts (cone, needle, and bark) of Pinus roxburghii were collected in Biratnagar, Nepal. The essential oils were obtained by hydrodistillation, and the chemical compositions were determined by GC-MS. The needle and cone essential oils were screened for anti-microbial activity against Bacillus cereus, Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, and Aspergillus niger; brine shrimp (Artemia salina) lethality; and in-vitro cytotoxicity against MCF-7 cells. Results: GC-MS analysis for the cone oil revealed 81 compounds with 78 components being identified (95.5% of the oil) while 98.3% of needle oil was identified to contain 68 components and 98.6% of the bark oil (38 components) was identified. The 3 essential oils were dominated by sesquiterpenes, particularly (E)-caryophyllene (26.8%-34.5%) and α-humulene (5.0%-7.3%) as well as monoterpene alcohols terpinen-4-ol (4.1%-30.1%) and α-terpineol(2.8%-5.0%). The monoterpene δ-3-carene was present only in needle and cone essential oils (2.3% and 6.8%, respectively). Bio-activity assays of the cone essential oil of P. roxburghii showed remarkable cytotoxic activity (100% killing of MCF-7 cells at 100 μg/mL) along with notable brine shrimp lethality (LC50 =11.8 μg/mL). The cone essential oil did not show anti-bacterial activity, but it did exhibit anti-fungal activity against Aspergillus niger (MIC=39 μg/mL). Conclusion: The bioactivity of P. roxburghii essential oil is consistent with its traditional medicinal use. PMID:23598924

Alterations in bottom sediment physical and chemical characteristics at the Terra Nova offshore oil development over ten years of drilling on the grand banks of Newfoundland, Canada

NASA Astrophysics Data System (ADS)

DeBlois, Elisabeth M.; Paine, Michael D.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Janes, G. Gregory

2014-12-01

This paper describes sediment composition at the Terra Nova offshore oil development. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland, Canada, at an approximate water depth of 100 m. Surface sediment samples (upper 3 cm) were collected for chemical and particle size analyses at the site pre-development (1997) and in 2000-2002, 2004, 2006, 2008 and 2010. Approximately 50 stations have been sampled in each program year, with stations extending from less than 1 km to a maximum of 20 km from source (drill centres) along five gradients, extending to the southeast, southwest, northeast, northwest and east of Terra Nova. Results show that Terra Nova sediments were contaminated with >C10-C21 hydrocarbons and barium-the two main constituents of synthetic-based drilling muds used at the site. Highest levels of contamination occurred within 1 to 2 km from source, consistent with predictions from drill cuttings dispersion modelling. The strength of distance gradients for >C10-C21 hydrocarbons and barium, and overall levels, generally increased as drilling progressed but decreased from 2006 to 2010, coincident with a reduction in drilling. As seen at other offshore oil development sites, metals other than barium, sulphur and sulphide levels were elevated and sediment fines content was higher in the immediate vicinity (less than 0.5 km) of drill centres in some sampling years; but there was no strong evidence of project-related alterations of these variables. Overall, sediment contamination at Terra Nova was spatially limited and only the two major constituents of synthetic-based drilling muds used at the site, >C10-C21 hydrocarbons and barium, showed clear evidence of project-related alternations.

Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

NASA Astrophysics Data System (ADS)

Burki, Milad; Darwish, Mohamed

2017-06-01

The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

Trichloroethylene and stoddard solvent reduction alternatives in a small shop. 1989 summer intern report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, D.J.

1989-12-31

Aero Precision Engineering Corp. is a small screw machine shop which produces precision parts for industry located in St. Paul Park, MN. The project focused on identifying satisfactory water-based substitutes for trichloroethylene (TCE) used both as a vapor degreaser and as a cold solvent in a small covered container. At the time of the project, the company used about 500 gallons of trichloroethylene with approximately 165 gallons shipped off site as waste annually. The solvent was used primarily to remove cutting oil and metal chips from production parts. In identifying a standard for evaluating alterantives to the solvent for cleaning,more » it was noted that parts cleaned in the cold bucket were definitely not as clean as those cleaned in the vapor degreaser.« less

Cut Bank Municipal Airport and Army Air Force Base, Terminal ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Cut Bank Municipal Airport and Army Air Force Base, Terminal Building, Approximately 390 yards west of Valier Highway (Montana Route 358), three miles southwest of Cut Bank, Cut Bank, Glacier County, MT

Microbial Desulfurization of a Crude Oil Middle-Distillate Fraction: Analysis of the Extent of Sulfur Removal and the Effect of Removal on Remaining Sulfur

PubMed Central

Grossman, M. J.; Lee, M. K.; Prince, R. C.; Garrett, K. K.; George, G. N.; Pickering, I. J.

1999-01-01

Rhodococcus sp. strain ECRD-1 was evaluated for its ability to desulfurize a 232 to 343°C middle-distillate (diesel range) fraction of Oregon basin (OB) crude oil. OB oil was provided as the sole source of sulfur in batch cultures, and the extent of desulfurization and the chemical fate of the residual sulfur in the oil after treatment were determined. Gas chromatography (GC), flame ionization detection, and GC sulfur chemiluminesce detection analysis were used to qualitatively evaluate the effect of Rhodococcus sp. strain ECRD-1 treatment on the hydrocarbon and sulfur content of the oil, respectively. Total sulfur was determined by combustion of samples and measurement of released sulfur dioxide by infrared absorption. Up to 30% of the total sulfur in the middle distillate cut was removed, and compounds across the entire boiling range of the oil were affected. Sulfur K-edge X-ray absorption-edge spectroscopy was used to examine the chemical state of the sulfur remaining in the treated OB oil. Approximately equal amounts of thiophenic and sulfidic sulfur compounds were removed by ECRD-1 treatment, and over 50% of the sulfur remaining after treatment was in an oxidized form. The presence of partially oxidized sulfur compounds indicates that these compounds were en route to desulfurization. Overall, more than two-thirds of the sulfur had been removed or oxidized by the microbial treatment. PMID:9872778

Artificial Intelligence Based Selection of Optimal Cutting Tool and Process Parameters for Effective Turning and Milling Operations

NASA Astrophysics Data System (ADS)

Saranya, Kunaparaju; John Rozario Jegaraj, J.; Ramesh Kumar, Katta; Venkateshwara Rao, Ghanta

2016-06-01

With the increased trend in automation of modern manufacturing industry, the human intervention in routine, repetitive and data specific activities of manufacturing is greatly reduced. In this paper, an attempt has been made to reduce the human intervention in selection of optimal cutting tool and process parameters for metal cutting applications, using Artificial Intelligence techniques. Generally, the selection of appropriate cutting tool and parameters in metal cutting is carried out by experienced technician/cutting tool expert based on his knowledge base or extensive search from huge cutting tool database. The present proposed approach replaces the existing practice of physical search for tools from the databooks/tool catalogues with intelligent knowledge-based selection system. This system employs artificial intelligence based techniques such as artificial neural networks, fuzzy logic and genetic algorithm for decision making and optimization. This intelligence based optimal tool selection strategy is developed using Mathworks Matlab Version 7.11.0 and implemented. The cutting tool database was obtained from the tool catalogues of different tool manufacturers. This paper discusses in detail, the methodology and strategies employed for selection of appropriate cutting tool and optimization of process parameters based on multi-objective optimization criteria considering material removal rate, tool life and tool cost.

Evaluation of comprehensive two-dimensional gas chromatography with flame photometric detection: potential application for sulfur speciation in shale oil.

PubMed

Mitrevski, Blagoj; Amer, Mohammad W; Chaffee, Alan L; Marriott, Philip J

2013-11-25

Flame photometric detection in the sulfur channel has been evaluated for sulfur speciation and quantification in comprehensive two-dimensional gas chromatography [GC × GC-FPD(S)] for S-compound speciation in shale extracts. Signal non-linearity and potential quenching effects were reportedly major limitations of this detector for analysis of sulfur in complex matrices. However, reliable linear relationships with correlation coefficient >0.99 can be obtained if the sum of the square root of each modulation slice in GC × GC is plotted vs. sulfur concentration. Furthermore, the quenching effects are reduced due to essentially complete separation of S-containing components from the hydrocarbon matrix. An increase of S/N of up to 150 times has been recorded for benzothiophene and dibenzothiophene in GC × GC-FPD when compared to GC-FPD due to the modulation process. As a consequence, 10 times lower detection limits were observed in the former mode. The applicability of the method was demonstrated using shale oil sample extracts. Three sulfur classes were completely separated and the target class (thiophenes) was successfully quantified after the rest of the sample was diverted to the second detector by using a heart-cut strategy. Based on the proposed method, 70% of the sulfur in the shale oil was assigned to the thiophenes, 24% to benzothiophenes, and 5% to dibenzothiophene compounds. Copyright © 2013 Elsevier B.V. All rights reserved.

Bio-Friendly Alternatives for Xylene – Carrot oil, Olive oil, Pine oil, Rose oil

PubMed Central

Nandan, Surapaneni Rateesh Kumar; Kulkarni, Pavan G.; Rao, Thokala Madhusudan; Palakurthy, Pavan

2015-01-01

Background Xylene is a flammable liquid with characteristic petroleum or aromatic odours, it is miscible with most of the organic solvents and paraffin wax. Xylene clears tissues rapidly and renders transparency, facilitating clearing endpoint determination, this made it to be used as a clearing agent in routine histopathological techniques. Even though it is a good clearing agent, it causes damage to the tissues by its hardening effect particularly those fixed in non-protein coagulant fixatives. Apart from these tissue effects, it has severe, long lasting ill effects on health of technicians and pathologists when exposed to longer duration. Hence in order to overcome these effects and replace xylene with a safe alternative agent, the present study was carried out to assess the clearing ability and bio-friendly nature of four different natural oils i.e., Carrot oil, Olive oil, Pine oil and Rose oil in comparison with that of Xylene. According to Bernoulli’s principle of fluid dynamics, to decrease viscosity of these oils and increase penetration into tissues for rapid clearing hot-air oven technique was used. Aims To assess:1) Clearing ability and bio-friendly nature of four different oils i.e., Carrot oil, Olive oil, Pine oil, Rose oil in comparison with that of xylene, 2) Application of Bernoulli’s principle of fluid dynamics in rapid clearing of tissues by using hot-air oven. Materials and Methods Forty different formalin fixed tissue samples were taken. Each sample of tissue was cut into 5 bits (40x5=200 total bits) which were subjected for dehydration in differential alcohol gradients. Later, each bit is kept in 4 different oils such as Carrot oil, Olive oil, Pine oil, Rose oil and xylene and transferred into hot-air oven. Further routine steps of processing, sectioning and staining were done. Individual sections cleared in four different oils were assessed for cellular architecture, staining quality and a comparison was done between them. Results Results showed that all the four oils had ability to clear the tissues similar to that of xylene. Pine oil was superior in its physical and clearing properties, which also maintained good cellular architecture and distinct staining quality, when compared with other oils and xylene. Conclusion Carrot oil, Olive oil, Pine oil, Rose oil, are not only bio friendly and economical but can also be used as clearing agent instead of xylene. In this study stability and longetivity of haematoxyllin and eosin staining was evaluated for over a period of one year and no significant difference in staining quality were observed. PMID:26673687

Fast pyrolysis oil from pinewood chips co-processing with vacuum gas oil in an FCC unit for second generation fuel production

DOE PAGES

Pinho, Andrea de Rezende; de Almeida, Marlon B. B.; Mendes, Fabio Leal; ...

2016-10-15

Raw bio-oil produced from fast pyrolysis of pine woodchips was co-processed with standard Brazilian vacuum gasoil (VGO) and tested in a 200 kg•h -1 fluid catalytic cracking (FCC) demonstration-scale unit using a commercial FCC equilibrium catalyst. Two different bio-oil/VGO weight ratios were used: 5/95 and 10/90. Co-processing of raw bio-oil in FCC was shown to be technically feasible. Bio-oil could be directly co-processed with a regular gasoil FCC feed up to 10 wt%. The bio-oil and the conventional gasoil were cracked into valuable liquid products such as gasoline and diesel range products. Most of the oxygen present in the bio-oilmore » was eliminated as water and carbon monoxide as these yields were always higher than that of carbon dioxide. Product quality analysis shows that trace oxygenates, primarily alkyl phenols, in FCC gasoline and diesel products are present with or without co-processing oxygenated intermediates. The oxygenate concentrations increase with co-processing, but have not resulted in increased concerns with quality of fuel properties. The presence of renewable carbon was confirmed in gasoline and diesel cuts through 14C isotopic analysis, showing that renewable carbon is not only being converted into coke, CO, and CO 2, but also into valuable refining liquid products. Thus, gasoline and diesel could be produced from lignocellulosic raw materials through a conventional refining scheme, which uses the catalytic cracking process. As a result, the bio-oil renewable carbon conversion into liquid products (carbon efficiency) was approximately 30%, well above the efficiency found in literature for FCC bio-oil upgrading.« less

Fast pyrolysis oil from pinewood chips co-processing with vacuum gas oil in an FCC unit for second generation fuel production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinho, Andrea de Rezende; de Almeida, Marlon B. B.; Mendes, Fabio Leal

Raw bio-oil produced from fast pyrolysis of pine woodchips was co-processed with standard Brazilian vacuum gasoil (VGO) and tested in a 200 kg•h -1 fluid catalytic cracking (FCC) demonstration-scale unit using a commercial FCC equilibrium catalyst. Two different bio-oil/VGO weight ratios were used: 5/95 and 10/90. Co-processing of raw bio-oil in FCC was shown to be technically feasible. Bio-oil could be directly co-processed with a regular gasoil FCC feed up to 10 wt%. The bio-oil and the conventional gasoil were cracked into valuable liquid products such as gasoline and diesel range products. Most of the oxygen present in the bio-oilmore » was eliminated as water and carbon monoxide as these yields were always higher than that of carbon dioxide. Product quality analysis shows that trace oxygenates, primarily alkyl phenols, in FCC gasoline and diesel products are present with or without co-processing oxygenated intermediates. The oxygenate concentrations increase with co-processing, but have not resulted in increased concerns with quality of fuel properties. The presence of renewable carbon was confirmed in gasoline and diesel cuts through 14C isotopic analysis, showing that renewable carbon is not only being converted into coke, CO, and CO 2, but also into valuable refining liquid products. Thus, gasoline and diesel could be produced from lignocellulosic raw materials through a conventional refining scheme, which uses the catalytic cracking process. As a result, the bio-oil renewable carbon conversion into liquid products (carbon efficiency) was approximately 30%, well above the efficiency found in literature for FCC bio-oil upgrading.« less

MELANOPHORE BANDS AND AREAS DUE TO NERVE CUTTING, IN RELATION TO THE PROTRACTED ACTIVITY OF NERVES

PubMed Central

Parker, G. H.

1941-01-01

1. When appropriate chromatic nerves are cut caudal bands, cephalic areas, and the pelvic fins of the catfish Ameiurus darken. In pale fishes all these areas will sooner or later blanch. By recutting their nerves all such blanched areas will darken again. 2. These observations show that the darkening of caudal bands, areas, and fins on cutting their nerves is not due to paralysis (Brücke), to the obstruction of central influences such as inhibition (Zoond and Eyre), nor to vasomotor disturbances (Hogben), but to activities emanating from the cut itself. 3. The chief agents concerned with the color changes in Ameiurus are three: intermedin from the pituitary gland, acetylcholine from the dispersing nerves (cholinergic fibers), and adrenalin from the concentrating nerves (adrenergic fibers). The first two darken the fish; the third blanches it. In darkening the dispersing nerves appear to initiate the process and to be followed and substantially supplemented by intermedin. 4. Caudal bands blanch by lateral invasion, cephalic areas by lateral invasion and internal disintegration, and pelvic fins by a uniform process of general loss of tint equivalent to internal disintegration. 5. Adrenalin may be carried in such an oil as olive oil and may therefore act as a lipohumor; it is soluble in water and hence may act as a hydrohumor. In lateral invasion (caudal bands, cephalic areas) it probably acts as a lipohumor and in internal disintegration (cephalic areas, pelvic fins) it probably plays the part of a hydrohumor. 6. The duration of the activity of dispersing nerves after they had been cut was tested by means of the oscillograph, by anesthetizing blocks, and by cold-blocks. The nerves of Ameiurus proved to be unsatisfactory for oscillograph tests. An anesthetizing block, magnesium sulfate, is only partly satisfactory. A cold-block, 0°C., is successful to a limited degree. 7. By means of a cold-block it can be shown that dispersing autonomic nerve fibers in Ameiurus can continue in activity for at least 6½ hours. It is not known how much longer they may remain active. So far as the duration of their activity is concerned dispersing nerve fibers in this fish are unlike other types of nerve fibers usually studied. PMID:19873231

Toxicity assessment of individual ingredients of synthetic-based drilling muds (SBMs).

PubMed

Bakhtyar, Sajida; Gagnon, Marthe Monique

2012-09-01

Synthetic-based drilling muds (SBMs) offer excellent technical characteristics while providing improved environmental performance over other drilling muds. The low acute toxicity and high biodegradability of SBMs suggest their discharge at sea would cause minimal impacts on marine ecosystems, however, chronic toxicity testing has demonstrated adverse effects of SBMs on fish health. Sparse environmental monitoring data indicate effects of SBMs on bottom invertebrates. However, no environmental toxicity assessment has been performed on fish attracted to the cutting piles. SBM formulations are mostly composed of synthetic base oils, weighting agents, and drilling additives such as emulsifiers, fluid loss agents, wetting agents, and brine. The present study aimed to evaluate the impact of exposure to individual ingredients of SBMs on fish health. To do so, a suite of biomarkers [ethoxyresorufin-O-deethylase (EROD) activity, biliary metabolites, sorbitol dehydrogenase (SDH) activity, DNA damage, and heat shock protein] have been measured in pink snapper (Pagrus auratus) exposed for 21 days to individual ingredients of SBMs. The primary emulsifier (Emul S50) followed by the fluid loss agent (LSL 50) caused the strongest biochemical responses in fish. The synthetic base oil (Rheosyn) caused the least response in juvenile fish. The results suggest that the impact of Syndrill 80:20 on fish health might be reduced by replacement of the primary emulsifier Emul S50 with an alternative ingredient of less toxicity to aquatic biota. The research provides a basis for improving the environmental performance of SBMs by reducing the environmental risk of their discharge and providing environmental managers with information regarding the potential toxicity of individual ingredients.

Optical properties and indentation hardness of thin-film acrylated epoxidized oil

NASA Astrophysics Data System (ADS)

Rahman, Mohammad Syuhaimi Ab.; Shaktur, Khaled Mohamed; Mohammad, Rahmah; Zalikha, Wan Aimi; Nawi, Norwimie; Mohd, Ahmad Faiza

2012-02-01

Epoxy acrylate has been widely used as optical resin for applications such as cladding, the core of a waveguide, and other photonic devices. In this study, sustainable resin from edible oil was used as an alternative to epoxy acrylate. Structural features and the transmission of planar thin-film resin from an ultraviolet-visible spectroscopy (UV-VIS) spectrometer were investigated upon UV exposure. It was found that high transmission still persists for all samples with and without an UV absorber for exposed and unexposed samples. The film was found to absorb strongly below 400 nm. A change in the cut-off wavelength was observed upon exposure. Thin-film hardness and its dynamic indentation in the load-unload mode with different test forces were evaluated. Vickers hardness and the elastic modulus were determined for unacrylated epoxidized soybean oil (ESO) and acrylated epoxidized soybean oil (AESO). It was found that the AESO has a higher Vickers hardness and elastic modulus than those of unacrylated thin film. The Vickers hardness and elastic modulus were found to increase as the applied test force increased. The refractive index, thickness, and modes present were characterized from a spin-coated planar thin film. The refractive index in the transverse electric mode (TE) and transverse magnetic mode (TM) were determined and compared for unacrylated and acrylated epoxidized oil.

Tuning of shell thickness of solid lipid particles impacts the chemical stability of encapsulated ω-3 fish oil.

PubMed

Salminen, Hanna; Helgason, Thrandur; Kristinsson, Bjarki; Kristbergsson, Kristberg; Weiss, Jochen

2017-03-15

This study demonstrates that tuning the shell thickness of lipid particles can modulate their oxidative stability. We hypothesized that a thick crystallized shell around the incorporated fish oil would improve the oxidative stability due to the reduced diffusion of prooxidants and oxygen. We prepared solid lipid nanoparticles (5%w/w lipid phase, 1.5%w/w surfactant, pH 7) by using different ratios of tristearin as carrier lipid and ω-3 fish oil as incorporated liquid lipid stabilized by high- or low-melting lecithin. The physical, polymorphic and oxidative stability of the lipid particles was assessed. The high-melting lecithin was the key in inducing the formation of a solidified tristearin shell around the lipid particles by interfacial heterogeneous nucleation. Lipid particles containing a higher ratio of tristearin showed a better oxidative stability. The results revealed that a crystallized tristearin layer above 10nm was required to inhibit oxidation of the incorporated fish oil. This cut-off was shown for lipid particles containing 50-60% fish oil. This research gives important insights into understanding the relation between the thickness of the crystallized shell around the lipid particles and their chemical stability. Copyright © 2016 Elsevier Inc. All rights reserved.

40 CFR Appendix A to Subpart Bb of... - State Requirements Incorporated by Reference in Subpart BB of Part 147 of the Code of Federal...

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Construction-no conflict with board of land commissioners' authority. Section 82-11-105 through 82-11-110... Cuttings. Rule 36.22.1013. Filing of Completion Reports, Well Logs, Analyses, Reports, and Surveys. Rule 36.... Gas Oil Ratio Tests. Rule 36.22.1217. Water Production Report. Rule 36.22.1218. Gas to be Metered...

40 CFR Appendix A to Subpart Bb of... - State Requirements Incorporated by Reference in Subpart BB of Part 147 of the Code of Federal...

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Construction-no conflict with board of land commissioners' authority. Section 82-11-105 through 82-11-110... Cuttings. Rule 36.22.1013. Filing of Completion Reports, Well Logs, Analyses, Reports, and Surveys. Rule 36.... Gas Oil Ratio Tests. Rule 36.22.1217. Water Production Report. Rule 36.22.1218. Gas to be Metered...

40 CFR Appendix A to Subpart Bb of... - State Requirements Incorporated by Reference in Subpart BB of Part 147 of the Code of Federal...

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Construction-no conflict with board of land commissioners' authority. Section 82-11-105 through 82-11-110... Cuttings. Rule 36.22.1013. Filing of Completion Reports, Well Logs, Analyses, Reports, and Surveys. Rule 36.... Gas Oil Ratio Tests. Rule 36.22.1217. Water Production Report. Rule 36.22.1218. Gas to be Metered...

40 CFR Appendix A to Subpart Bb of... - State Requirements Incorporated by Reference in Subpart BB of Part 147 of the Code of Federal...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Construction-no conflict with board of land commissioners' authority. Section 82-11-105 through 82-11-110... Cuttings. Rule 36.22.1013. Filing of Completion Reports, Well Logs, Analyses, Reports, and Surveys. Rule 36.... Gas Oil Ratio Tests. Rule 36.22.1217. Water Production Report. Rule 36.22.1218. Gas to be Metered...

40 CFR Appendix A to Subpart Bb of... - State Requirements Incorporated by Reference in Subpart BB of Part 147 of the Code of Federal...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Construction-no conflict with board of land commissioners' authority. Section 82-11-105 through 82-11-110... Cuttings. Rule 36.22.1013. Filing of Completion Reports, Well Logs, Analyses, Reports, and Surveys. Rule 36.... Gas Oil Ratio Tests. Rule 36.22.1217. Water Production Report. Rule 36.22.1218. Gas to be Metered...

Exploration cost-cutting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huttrer, J.

This presentation by Jerry Huttrer, President, Geothermal Management Company, discusses the general state of exploration in the geothermal industry today, and mentions some ways to economize and perhaps save costs of geothermal exploration in the future. He suggests an increased use of satellite imagery in the mapping of geothermal resources and the identification of hot spots. Also, coordinating with oil and gas exploration efforts, the efficiency of the exploration task could be optimized.

Iran’s Economic Conditions: U.S. Policy Issues

DTIC Science & Technology

2010-04-22

trade and financial isolation. Iran’s economy is highly dependent on the production and export of crude oil to finance government spending, and...January 2010, the Iranian parliament approved a subsidy reform plan that would cut government subsidies on fuel and other goods and services...a central focus of U.S. national security policy. The United States has designated the Iranian government as a state sponsor of terrorism. The

The Use of Films as Suitable Packaging Materials for Minimally Processed Foods

DTIC Science & Technology

1994-08-01

subway stations. Many of these lunch box vending machines are serving lunches with no refrigeration. Ihe secret is the application of antimicrobial...Ooating: Convenience foods with different components bearing different water activity, oil content, or other migrating components (e.g., a sandwich ...growing in the barrier properties of edible film such as protein/lipid complexes that prevent dehydration of cut vegetables or a sandwich filling from

Carbon Coating Of Copper By Arc-Discharge Pyrolysis

NASA Technical Reports Server (NTRS)

Ebihara, Ben T.; Jopek, Stanley

1988-01-01

Adherent, abrasion-resistant coat deposited with existing equipment. Carbon formed and deposited as coating on copper substrate by pyrolysis of hydrocarbon oil in electrical-arc discharges. Technique for producing carbon deposits on copper accomplished with electrical-discharge-machining equipment used for cutting metals. Applications for new coating technique include the following: solar-energy-collecting devices, coating of metals other than copper with carbon, and carburization of metal surfaces.

Slicing of silicon into sheet material. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

NASA Technical Reports Server (NTRS)

Holden, S. C.; Fleming, J. R.

1978-01-01

Fabrication of a prototype large capacity multiple blade slurry saw is considered. Design of the bladehead which will tension up to 1000 blades, and cut a 45 cm long silicon ingot as large as 12 cm in diameter is given. The large blade tensioning force of 270,000 kg is applied through two bolts acting on a pair of scissor toggles, significantly reducing operator set-up time. Tests with an upside-down cutting technique resulted in 100% wafering yields and the highest wafer accuracy yet experienced with MS slicing. Variations in oil and abrasives resulted only in degraded slicing results. A technique of continuous abrasive slurry separation to remove silicon debris is described.

The Larger the Viscosity, the Higher the Bounce

NASA Astrophysics Data System (ADS)

Stern, Menachem; Klein Schaarsberg, Martin; Peters, Ivo; Dodge, Kevin; Zhang, Wendy; Jaeger, Heinrich

A low-viscosity liquid drop can bounce upon impact onto a solid. A high-viscosity drop typically just flattens, i.e., it splats. Surprisingly, our experiments with a droplet made of densely packed glass beads in silicone oil display the opposite behavior: the low-viscosity oil suspension drop splats. The high-viscosity oil suspension bounces. Increasing solvent viscosity increases the rebound energy. To gain insight into the underlying mechanism, we model the suspension as densely packed elastic spheres experiencing viscous lubrication drag between neighbors. The model reproduces the observed trends. Plots of elastic compression and drag experienced by the particles show that rebounds are made possible by (1) a fraction of the impact energy being stored during initial contact via elastic compression, (2) a rapid broadening of local lubrication drag interactions at the initial impact site into a spatially uniform upward force throughout the drop. Including finite wall drag due to the presence of ambient air into the numerical model diminishes and eventually cuts off the rebound.

Characterization of visual pigments, oil droplets, lens and cornea in the whooping crane Grus americana

PubMed Central

Porter, Megan L.; Kingston, Alexandra C. N.; McCready, Robert; Cameron, Evan G.; Hofmann, Christopher M.; Suarez, Lauren; Olsen, Glenn H.; Cronin, Thomas W.; Robinson, Phyllis R.

2014-01-01

Vision has been investigated in many species of birds, but few studies have considered the visual systems of large birds and the particular implications of large eyes and long-life spans on visual system capabilities. To address these issues we investigated the visual system of the whooping crane Grus americana (Gruiformes, Gruidae), which is one of only two North American crane species. It is a large, long-lived bird in which UV sensitivity might be reduced by chromatic aberration and entrance of UV radiation into the eye could be detrimental to retinal tissues. To investigate the whooping crane visual system we used microspectrophotometry to determine the absorbance spectra of retinal oil droplets and to investigate whether the ocular media (i.e. the lens and cornea) absorb UV radiation. In vitro expression and reconstitution was used to determine the absorbance spectra of rod and cone visual pigments. The rod visual pigments had wavelengths of peak absorbance (λmax) at 500 nm, whereas the cone visual pigment λmax values were determined to be 404 nm (SWS1), 450 nm (SWS2), 499 nm (RH2) and 561 nm (LWS), similar to other characterized bird visual pigment absorbance values. The oil droplet cut-off wavelength (λcut) values similarly fell within ranges recorded in other avian species: 576 nm (R-type), 522 nm (Y-type), 506 nm (P-type) and 448 nm (C-type). We confirm that G. americana has a violet-sensitive visual system; however, as a consequence of the λmax of the SWS1 visual pigment (404 nm), it might also have some UV sensitivity. PMID:25267845

Environmental impact assessment of oilfield upgrades in Bohai Sea

NASA Astrophysics Data System (ADS)

Chen, Ruihui; Xiong, Yanna; Li, Jiao; Li, Xianbo

2018-02-01

This paper designed 65 environmental monitoring sites to collect samples and analyze for better evaluating the environmental impact generated by cuttings, mud, produced water with oil and oil pollutions that produced during the upgrading in the Bohai Sea where the oil field 34-1 upgraded. Collecting samples include ocean water, marine life and sediments and test items involve PH, dissolved oxygen (DO), salinity, chemical oxygen demand (COD), phosphate, organic carbon, sulfide, inorganic nitrogen, petroleum, copper (Cu), lead (Pb), zinc (Zn), cadmium (Cd), total chromium (Cr), total mercury (Hg) and arsenic (As). Meanwhile sample sites collect and analyze the abundance and diversity of marine plants and elaborated the environmental impact caused by upgrading renovation project from the aspects of sea water, marine life and marine sediments. Through analysis and comparison we found that seawater quality conform the Ш seawater quality standards, the excessive rate of Cu is 10%, the average diversity index of marine life is 2.34 and evenness is 0.68. Influence range of marine sediments and pollutants of production is within 2.68km and basically has no serious impact in the surrounding sea area. It’s worth nothing that reconstruction project has the risk of oil spilling and protective measures must be prepared.

Penny-pinching strategy pays off at the gas pumps. [Hudson Oil Co

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nazem, S.G.

1978-06-05

Mary Hudson Vandergrift is president and chief executive of Hudson Oil Company. She reigns over the oldest and one of the largest independent gasoline-marketing companies in the U.S., with 300 service stations scattered across thirty-six states, and her own refinery. Her company rang up sales of $230 million last year, and FORTUNE estimates that profits were in the neighborhood of $10 million. Many of Miss Hudson's strategies in gasoline marketing have been getting to be commonplace in the business. She runs a lean operation, cutting costs to the bone. She shuns grease racks and service bays; at each station amore » small, austere kiosk houses only a cash box and rest rooms. Most customers must serve themselves. She undersells the major oil companies by 1 to 2 cents per gallon. Her refinery turns out 450,000 gallons of gasoline daily, enough to fill 50% of Hudson's retail needs and for every barrel of crude it refines, Hudson Oil gets a rebate of about $2 from the government as part of the entitlements program that aims to keep small refiners competitive with the majors. (MCW)« less

Antimicrobial activity of the essential oil from Lippia sidoides, carvacrol and thymol against oral pathogens.

PubMed

Botelho, M A; Nogueira, N A P; Bastos, G M; Fonseca, S G C; Lemos, T L G; Matos, F J A; Montenegro, D; Heukelbach, J; Rao, V S; Brito, G A C

2007-03-01

Dental caries and periodontal disease are associated with oral pathogens. Several plant derivatives have been evaluated with respect to their antimicrobial effects against such pathogenic microorganisms. Lippia sidoides Cham (Verbenaceae), popularly known as "Alecrim-pimenta" is a typical shrub commonly found in the Northeast of Brazil. Many plant species belonging to the genus Lippia yield very fragrant essential oils of potential economic value which are used by the industry for the commercial production of perfumes, creams, lotions, and deodorants. Since the leaves of L. sidoides are also extensively used in popular medicine for the treatment of skin wounds and cuts, the objective of the present study was to evaluate the composition and antimicrobial activity of L. sidoides essential oil. The essential oil was obtained by hydro-distillation and analyzed by GC-MS. Twelve compounds were characterized, having as major constituents thymol (56.7%) and carvacrol (16.7%). The antimicrobial activity of the oil and the major components was tested against cariogenic bacterial species of the genus Streptococcus as well as Candida albicans using the broth dilution and disk diffusion assays. The essential oil and its major components thymol and carvacrol exhibited potent antimicrobial activity against the organisms tested with minimum inhibitory concentrations ranging from 0.625 to 10.0 mg/mL. The most sensitive microorganisms were C. albicans and Streptococcus mutans. The essential oil of L. sidoides and its major components exert promising antimicrobial effects against oral pathogens and suggest its likely usefulness to combat oral microbial growth.

Degumming of crude palm oil by membrane filtration.

PubMed

Ong, K K; Fakhru'l-Razi, A; Baharin, B S; Hassan, M A

1999-01-01

The application of membrane separation in palm oil refining process has potential for energy and cost savings. The conventional refining of crude palm oil results in loss of oil and a contaminated effluent. Degumming of crude palm oil by membrane technology is conducted in this study. The objective of this research is to study the feasibility of membrane filtration for the removal of phospholipids in the degumming of crude palm oil, including analyses of phosphorus content, carotene content free fatty acids (as palmitic acid), colour and volatile matter. A PCI membrane module was used which was equipped with polyethersulfone membranes having a molecular weight cut off of 9,000 (type ES209). In this study, phosphorus content was the most important parameter monitored. The membrane effectively removed phospholipids resulting in a permeate with a phosphorus content of less than 0.3 ppm The percentage removal of phosphorus was 96.4% and was considered as a good removal. Lovibond colour was reduced from 27R 50Y to 20R 30Y. The percentage removal of carotene was 15.8%. The removal of colour was considered good but the removal of carotene was considered insignificant by the membrane. Free fatty acids and volatile matter were not removed. Typical of membrane operations, the permeate flux decreased with time and must be improved in order to be adopted on an industrial scale. Membrane technology was found to have good potential in crude palm oil degumming. However, an appropriate method has to be developed to clean the membranes for reuse.

Fiscal year 2013 energy department budget: Proposed investments in clean energy research

NASA Astrophysics Data System (ADS)

Balcerak, Ernie

2012-03-01

Energy and environmental research programs generally fared well in President Barack Obama's proposed budget for the Department of Energy (DOE) for fiscal year (FY) 2013. In his State of the Union address, Obama called for the United States to pursue an "all of the above" energy strategy that includes fossil fuels, as well as a variety of renewable sources of energy. The DOE budget request supports that strategy, Energy Secretary Steven Chu said in a 13 February press briefing announcing the budget proposal. The proposed budget gives DOE 27.2 billion overall, a 3.2% increase from the FY 2012 enacted budget (see Table 1). This budget "reflects some tough choices," Chu said. The proposed budget would cut 4 billion in subsidies for oil and gas companies; many Republican members of Congress have already indicated that they oppose such cuts, suggesting that congressional approval of this budget may run into stumbling blocks. The budget would also cut funding for research and development projects that are already attracting private-sector investment or that are not working, and would reduce some of the department's operational costs.

On-line coupled high performance liquid chromatography-gas chromatography for the analysis of contamination by mineral oil. Part 2: migration from paperboard into dry foods: interpretation of chromatograms.

PubMed

Biedermann, Maurus; Grob, Koni

2012-09-14

Mineral oil hydrocarbons are complex as well as varying mixtures and produce correspondingly complex chromatograms (on-line HPLC-GC-FID as described in Part 1): mostly humps of unresolved components are obtained, sometimes with sharp peaks on top. Chromatograms may also contain peaks of hydrocarbons from other sources which need to be subtracted from the mineral oil components. The review focuses on the interpretation and integration of chromatograms related to food contamination by mineral oil from paperboard boxes (off-set printing inks and recycled fibers), if possible distinguishing between various sources of mineral oil. Typical chromatograms are shown for relevant components and interferences as well as food samples encountered on the market. Details are pointed out which may provide relevant information. Integration is shown for examples of paperboard packaging materials as well as various foods. Finally the uncertainty of the analysis and limit of quantitation are discussed for specific examples. They primarily result from the interpretation of the chromatogram, manually placing the baseline and cuts for taking off extraneous components. Without previous enrichment, the limit of quantitation is between around 0.1 mg/kg for foods with a low fat content and 2.5 mg/kg for fats and oils. The measurement uncertainty can be kept clearly below 20% for most samples. Copyright © 2012 Elsevier B.V. All rights reserved.

Salem limestone oil and gas production in the Keenville field, Wayne County, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stevenson, D.L.

Oil has been produced from the Salem Limestone of Valmeyeran (middle Mississippian) age in Illinois since 1939. In 1972 the discovery of Salem oil at Zenith North field in Wayne County, Illinois, stimulated a resurgence of Salem exploration in the Illinois Basin. By the end of 1977, activity had resulted in 3 new field discoveries and 24 new pool discoveries in the Salem of Illinois. One of the most promising of these discoveries was in the Keenville field in T. 1 S., R. 5 E., Wayne County, Illinois. The discovery well was completed early in January 1977, and by themore » end of the year 40 wells had produced approximately 760,000 barrels of Salem oil. The oil is produced from a biocalcarenite (predominatly sand-sized fossils and fossil fragments), with highly variable porosity and permeability, which lies about midway between the top and bottom of the formation. No structural closure is evident on key marker beds above the Salem, but some closure is created by the tendency of the producing zone to occur increasingly lower in the section in an up-dip direction. Water-free oil production was obtained in many wells by setting pipe through the reservoir and perforating above the oil-water contact, as determined by examination of drill cuttings. The oil produced is accompanied by gas with a heating value of about 1500 Btu/ft/sup 3/. To date, most of the oil accumulations in the Salem have been found by drilling below shallower, producing zones on prominent structures. The presence of reservoirs within the Salem, such as the one at Keenville has been difficult to predict prior to drilling. The recent increase in the number of holes drilled to or through the Salem should add to our knowledge of its depositional and diagenetic history and help in further oil exploration.« less

Processing liquid organic wastes at the NNL Preston laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coppersthwaite, Duncan; Greenwood, Howard; Docrat, Tahera

2013-07-01

Organic compounds of various kinds have been used in the nuclear industry for numerous duties in uranium chemical, metal and ceramic processing plants. In the course of the various operations undertaken, these organic compounds have become contaminated with uranic material, either accidentally or as an inevitable part of the process. Typically, the chemical/physical form and/or concentration of the uranic content of the organics has prevented disposal. In order to address the issue of contaminated liquid organic wastes, the National Nuclear Laboratory (NNL) has developed a suite of treatments designed to recover uranium and to render the waste suitable for disposal.more » The developed processes are operated at industrial scale via the NNL Preston Laboratory Residue Processing Plant. The Oil Waste Leaching (OWL) Process is a fully industrialised process used for the treatment of contaminated oils with approximately 200 tonnes of uranium contaminated oil being treated to date. The process was originally developed for the treatment of contaminated tributyl phosphate and odourless kerosene which had been adsorbed onto sawdust. However, over the years, the OWL process has been refined for a range of oils including 'water emulsifiable' cutting oils, lubricating oils, hydraulic oils/fluids and 'Fomblin' (fully fluorinated) oils. Chemically, the OWL process has proved capable of treating solvents as well as oils but the highly volatile/flammable nature of many solvents has required additional precautions compared with those required for oil treatment. These additional precautions led to the development of the Solvent Treatment Advanced Rig (STAR), an installation operated under an inert atmosphere. STAR is a small 'module' (100 dm{sup 3} volume) which allows the treatment of both water miscible and immiscible solvents. This paper discusses the challenges associated with the treatment of liquid organic wastes and the process developments which have allowed a wide range of materials to be successfully treated. (authors)« less

Low excess air burners keep boiler and air cleaner while cutting fuel costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, H.

1981-11-01

In the 1970s at the Humko Chemical Co., producers of fatty acids used in plastics, soaps, rubber products, and textiles, it was deemed necessary to modify existing boiler equipment to insure an adequate fuel supply and to increase efficienct. Existing equipment operated at an overall average efficiency of 77% and only 6% excess O/sub 2/ could be achieved with number 6 fuel oil and only 2.6% with natural gas. Cleaning the boilers and replacing existing burners with oil and gas firing units led to overall efficiency up to 84% with only 1% excess O/sub 2/. Even though fuel costs havemore » approximately tripled during the ensuing time, Humko's cost of producing steam has only doubled with the more efficienct equipment. (BLM)« less

A Comparative Study of Natural Antimicrobial Delivery Systems for Microbial Safety and Quality of Fresh-Cut Lettuce.

PubMed

Hill, Laura E; Oliveira, Daniela A; Hills, Katherine; Giacobassi, Cassie; Johnson, Jecori; Summerlin, Harvey; Taylor, T Matthew; Gomes, Carmen L

2017-05-01

Nanoencapsulation can provide a means to effectively deliver antimicrobial compounds and enhance the safety of fresh produce. However, to date there are no studies which directly compares how different nanoencapsulation systems affect fresh produce safety and quality. This study compared the effects on quality and safety of fresh-cut lettuce treated with free and nanoencapsulated natural antimicrobial, cinnamon bark extract (CBE). A challenge study compared antimicrobial efficacy of 3 different nanoencapsulated CBE systems. The most effective antimicrobial treatment against Listeria monocytogenes was chitosan-co-poly-N-isopropylacrylamide (chitosan-PNIPAAM) encapsulated CBE, with a reduction on bacterial load up to 2 log 10 CFU/g (P < 0.05) compared to the other encapsulation systems when fresh-cut lettuce was stored at 5 °C and 10 °C for 15 d. Subsequently, chitosan-PNIPAAM-CBE nanoparticles (20, 40, and 80 mg/mL) were compared to a control and free CBE (400, 800, and 1600 μg/mL) for its effects on fresh-cut lettuce quality over 15 d at 5 °C. By the 10th day, the most effective antimicrobial concentration was 80 mg/mL for chitosan-PNIPAAM-CBE, up to 2 log 10 CFU/g reduction (P < 0.05), compared with the other treatments. There was no significant difference between control and treated samples up to day 10 for the quality attributes evaluated. Chitosan-PNIPAAM-CBE nanoparticles effectively inhibited spoilage microorganisms' growth and extended fresh-cut lettuce shelf-life. Overall, nanoencapsulation provided a method to effectively deliver essential oil and enhanced produce safety, while creating little to no detrimental quality changes on the fresh-cut lettuce. © 2017 Institute of Food Technologists®.

Effects of a fish oil-based emulsion on rat hepatoma cell invasion in culture.

PubMed

Hagi, Akifumi; Nakayama, Mitsuo; Miura, Yutaka; Yagasaki, Kazumi

2007-01-01

Total parenteral nutrition containing a lipid emulsion is often employed after surgical tumor resection. This study investigated the effects of a fish oil-based infusion on rat hepatoma cell invasion. Rat ascites hepatoma cell line AH109A was precultured with a fish oil-based or safflower oil-based emulsion for 48 h. Changes in membranous fatty acid composition were evaluated by gas chromatography. The invasiveness of hepatoma cells was assessed by coculturing with mesentery-derived mesothelial cells. To examine ex vivo effects of the fish oil-based infusion on hepatoma invasion, sera were prepared from rats infused with fish oil- or safflower oil-based emulsion and the effects of these sera were assessed. To clarify the mechanism of inhibition of invasion by the fish oil-based emulsion, the effects of prostaglandin (PG) E(2) and PGE(3) on invasion were examined. Pretreatment with the fish oil-based emulsion reduced invasiveness without affecting growth compared with the safflower oil-based emulsion. Pretreatment with the sera from rats infused with the fish oil-based emulsion also reduced invasiveness compared with the sera from rats infused with the safflower oil-based emulsion. The addition of PGE(2) eliminated the inhibitory effect of the fish oil-based emulsion, and the addition of PGE(3) reduced the invasiveness of hepatoma cells pretreated with the safflower oil-based emulsion. These results suggest that the fish oil-based emulsion may have anti-invasive effects. Changes in the membranous fatty acid composition and consequent changes in the prostaglandins produced may be involved in this inhibitory effect.

Graph-Cut Methods for Grain Boundary Segmentation (Preprint)

DTIC Science & Technology

2011-06-01

metals and metal alloys ) are among the strongest determinants of many material properties, such as mechanical strength or fracture resistance. In materials...cropped) Ni-based alloy image (a) using normalized cut (b) and ratio cut (c). Similar to normalized cut is the average-cut approach [11], where the...framework [2]. (a) (b) (c) Figure 3: Segmentation of a (cropped) Ni-based alloy image by optimal labeling. (a) Segmented grain bound- aries in a template

Effects of Different Cutting Patterns and Experimental Conditions on the Performance of a Conical Drag Tool

NASA Astrophysics Data System (ADS)

Copur, Hanifi; Bilgin, Nuh; Balci, Cemal; Tumac, Deniz; Avunduk, Emre

2017-06-01

This study aims at determining the effects of single-, double-, and triple-spiral cutting patterns; the effects of tool cutting speeds on the experimental scale; and the effects of the method of yield estimation on cutting performance by performing a set of full-scale linear cutting tests with a conical cutting tool. The average and maximum normal, cutting and side forces; specific energy; yield; and coarseness index are measured and compared in each cutting pattern at a 25-mm line spacing, at varying depths of cut per revolution, and using two cutting speeds on five different rock samples. The results indicate that the optimum specific energy decreases by approximately 25% with an increasing number of spirals from the single- to the double-spiral cutting pattern for the hard rocks, whereas generally little effect was observed for the soft- and medium-strength rocks. The double-spiral cutting pattern appeared to be more effective than the single- or triple-spiral cutting pattern and had an advantage of lower side forces. The tool cutting speed had no apparent effect on the cutting performance. The estimation of the specific energy by the yield based on the theoretical swept area was not significantly different from that estimated by the yield based on the muck weighing, especially for the double- and triple-spiral cutting patterns and with the optimum ratio of line spacing to depth of cut per revolution. This study also demonstrated that the cutterhead and mechanical miner designs, semi-theoretical deterministic computer simulations and empirical performance predictions and optimization models should be based on realistic experimental simulations. Studies should be continued to obtain more reliable results by creating a larger database of laboratory tests and field performance records for mechanical miners using drag tools.

Getting Over the Barrel- Achieving Independence from Foreign Oil in 2018

DTIC Science & Technology

2009-02-03

material called kerogen. Kerogen can be converted into oil via heating in the chemical process of pyrolysis .44 Depending on the richness of oil shale, it...vegetable oil, animal fat, corn , soybeans, jatropha seed oil, palm oil, switch grass and even algae. Biofuel production techniques and technologies...vary widely based on the input source – sugar-based, starch-based or oil-based. This document only examines corn -based ethanol production. The other

THE GENERATION, USE AND DISPOSAL OF WASTE CRANKCASE OIL IN DEVELOPING COUNTRIES: A CASE FOR KAMPALA DISTRICT, UGANDA

PubMed Central

Ssempebwa, John C.; Carpenter, David O.

2008-01-01

Waste Crankcase Oil (WCO), the oil that is removed from motor engines during an oil change, is frequently discarded into the environment, resulting in pollution of both aquatic and terrestrial ecosystems. In some developing countries, this common hazardous material is not properly managed. In Uganda little is known about its generation, utilization, and disposal. These factors were investigated using in-depth interviews of a sample of mechanics from 379 motor repair garages and 109 fuel stations in the Kampala district. Most garages (94%) and fuel stations (96%) in the study area offered oil-changing services. On average, each garage produced 62 litres, and each fuel station produced 134 litres of WCO per week. In garages 35% was sold, 16% poured on the ground, 18% taken by vehicle owners and 31% given away for free. At fuel stations, 49% was picked by private collectors, 27% sold, 4% poured on the ground, 2% burnt, 13% taken by vehicle owners, and 6% given away for free. Uses of WCO included coating roofing timber and fencing posts, use in timber cutting, marking play grounds, and pest control in animals. Its disposal involved burning, and pouring in the environment. Lack of policy and information for proper handling of WCO contributed to the poor management of WCO exhibited. PMID:18513868

3-D seismic data for field development: Landslide field case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raeuchle, S.K.; Carr, T.R.; Tucker, R.D.

1990-05-01

The Landslide field is located on the extreme southern flank of the San Joaquin basin, approximately 25 mi south of Bakersfield, California. The field, discovered in 1985, has produced in excess 9 million bbl of oil with an estimated ultimate recovery of more than 13 MMBO. The Miocene Stevens sands, which form the reservoir units at Landslide field, are interpreted as a series of constructional submarine fan deposits. Deposition of the fans was controlled by paleotopography with an abrupt updip pinch-out of the sands to the southwest. The three-dimensional seismic data over the field was used to locate the bottommore » hole of the landslide 22X-30 development well as close to this abrupt updip pinchout as possible in order to maximize oil recovery. A location was selected two traces (330 ft) from the updip pinch-out as mapped on the seismic data. The well was successfully drilled during 1989, encountering 150 ft of net sand with initial production in excess of 1,500 bbl of oil/day. A pressure buildup test indicates the presence of a boundary approximately 200 ft from the well bore. This boundary is interpreted as the updip pinchout of the Stevens sands against the paleohigh. Based on examination of changes in amplitude, the absence or presence of reservoir-quality sand can be mapped across the paleohighs. Application of three-dimensional seismic data, integration with well data, and in particular reconstruction cuts tied closely to existing wells can be used to map the ultimate extent of the field and contribute to efficient development.« less

Effects of crude glycerin from waste vegetable oil in diets on performance and carcass characteristics of feedlot goats.

PubMed

Chanjula, Pin; Cherdthong, Anusorn

2018-04-01

This experiment was conducted to investigate the effects of crude glycerin from waste vegetable oil (CGWVO) on performance, carcass traits, meat quality, and muscle chemical composition. Twenty-four crossbred (Thai Native×Anglo Nubian) uncastrated male goats (16.8± 0.46 kg body weight [BW]) were assigned to a completely randomized design and subjected to four experimental diets containing 0%, 2%, 4%, and 6% of CGWVO (63.42% of glycerol and 47.78% of crude fat) on a dry matter (DM) basis. The diets were offered ad libitum as total mixed rations twice daily. The feed intake, feeding behavior, growth performance, carcass and meat traits, and muscle chemical composition were evaluated. Based on this experiment, there were significant differences (p>0.05) among groups regarding DM intake, growth performance, and carcass traits where goats receiving 6% of CGWVO had lower daily DM intake, growth performance, and carcass traits than those fed on 0%, 2%, and 4% of CGWVO. There were no effects of CGWVO on carcass length, carcass width, Longissimus muscle (LM) area, Warner-Bratzler shear force, pH and color of LM at 45 min after slaughter, as well as on other carcass cut and muscle chemical composition. In conclusion, the addition of up to 4% of DM in the diets for crossbred finishing goats seems to be the most interesting strategy, since it promotes greatest animal performance. Moreover, this study was a suitable approach to exploit the use of biodiesel production from waste vegetable oil for goat production.

Effects of crude glycerin from waste vegetable oil in diets on performance and carcass characteristics of feedlot goats

PubMed Central

2018-01-01

Objective This experiment was conducted to investigate the effects of crude glycerin from waste vegetable oil (CGWVO) on performance, carcass traits, meat quality, and muscle chemical composition. Methods Twenty-four crossbred (Thai Native×Anglo Nubian) uncastrated male goats (16.8± 0.46 kg body weight [BW]) were assigned to a completely randomized design and subjected to four experimental diets containing 0%, 2%, 4%, and 6% of CGWVO (63.42% of glycerol and 47.78% of crude fat) on a dry matter (DM) basis. The diets were offered ad libitum as total mixed rations twice daily. The feed intake, feeding behavior, growth performance, carcass and meat traits, and muscle chemical composition were evaluated. Results Based on this experiment, there were significant differences (p>0.05) among groups regarding DM intake, growth performance, and carcass traits where goats receiving 6% of CGWVO had lower daily DM intake, growth performance, and carcass traits than those fed on 0%, 2%, and 4% of CGWVO. There were no effects of CGWVO on carcass length, carcass width, Longissimus muscle (LM) area, Warner-Bratzler shear force, pH and color of LM at 45 min after slaughter, as well as on other carcass cut and muscle chemical composition. Conclusion In conclusion, the addition of up to 4% of DM in the diets for crossbred finishing goats seems to be the most interesting strategy, since it promotes greatest animal performance. Moreover, this study was a suitable approach to exploit the use of biodiesel production from waste vegetable oil for goat production. PMID:28830128

Powerful motors: Kinship, citizenship and the transformation of the Argentine oil industry

NASA Astrophysics Data System (ADS)

Shever, Elana

The privatization of the Argentine oil industry has been described as an unprecedented transfer of property, capital and control from the state to the corporate sphere, but this study demonstrates that the privatization process is better understood as a transformation of the historical configurations of oil-fueled development, political communities and human subjectivities. This dissertation probes the development of the state-led oil industry, and the shift to a corporate-led one, through an ethnography of Argentines differently positioned in relation to the global oil industry. The ethnography explores the lives of middle class oil workers and their families in Northwest Patagonia, impoverished residents of the shanty neighborhoods near the refineries in metropolitan Buenos Aires, and affluent employees of the translocal corporations operating in the Argentine oil fields. After the Introduction delineates this study's four principal interventions into anthropological scholarship, each subsequent chapter engages a particular problem that cuts across the Argentine oil fields and the anthropological theoretical fields. Chapter Two scrutinizes the historical construction of the Argentine subterritory as a "natural" space of value. Chapters Three and Four investigate the articulation of capitalist production and filial reproduction. These chapters argue that sentiment is a crucial generative force that has shaped the oil industry, company towns and worker families from the founding of the state-owned oil company in beginning of the twentieth century to its conversion into a corporate-owned one at the century's close. Chapters Five and Six examine the emergence of consumer citizenship and corporate citizenship out of Argentine neoliberalismo and its transformation of the oil industry. They argue that consumer and corporate citizenship are both reformulations of the older traditions of liberalism and Peronism. All the chapters of this dissertation illustrate that the neoliberal transformation of the Argentine oil industry mutually reconfigured the statal, corporate and domestic domains, and through this process, remade personhood and relationality. They particularly scrutinize the complex web of power relationships that comprise the corporate domain, and argue that the seemingly invincible corporations that inhabit the contemporary world are the effects of a contingent historical process of redomaining people, materials and activities.

The Research of New Environment-Friendly Oil-based Drilling Fluid Base Oil

NASA Astrophysics Data System (ADS)

Sui, Dianjie; Sun, Yuxue; Zhao, Jingyuan; Zhao, Fulei; Zhu, Xiuyu; Xu, Jianjun

2018-01-01

In this paper, the heavy hydrocarbon of Daqing is used, and the desulfurization and de-aromatization experiments and refining process are carried out, A base oil suitable for oil-based drilling fluid was developed, and the performance of base oil was evaluated, we can know the aromatics content of oil base is low, less toxic, less pollution and it can meet the requirement of environmental protection.

Watching fat digestion: a microscopic method assessing intraluminal lipolysis.

PubMed

Alliet, P; Eggermont, E

1990-01-01

We investigated the utility of a microscopic method assessing lipolytic activity of duodenal fluid. The method is based on evaluating microscopically physicochemical changes along time when olive oil is mixed with duodenal fluid in the presence of excess bile salts (13 mM) and calcium ions (8 mM) at pH 6.5. Data are analyzed on duodenal aspirations from 155 children referred for failure to thrive or gastrointestinal disorders. The "fat digestion index" (FDI) is the percentage of intact olive oil droplets that underwent complete hydrolysis or are transformed into amorphous reticular bodies (ARB) at steady state. In all patients with proven exocrine pancreatic disorder, a FDI less than 25% was found. This value was thus considered as a cut-off value. When no microscopic lipolysis (FDI = 0) was observed, exocrine pancreatic enzyme assays are suggestive for a total exocrine pancreatic insufficiency. In the group of children with FDI ranging 5-25%, however, no statistical difference in exocrine pancreatic enzymes could be found, as compared to control values. Our tests thus evaluate fat digestion in a dynamic way. It further seems to give additional information on intraluminal lipolysis as compared to exocrine pancreatic enzyme concentrations, since it gives an idea about the integrated action of (co)lipase and bile salts.

ILP-based co-optimization of cut mask layout, dummy fill, and timing for sub-14nm BEOL technology

NASA Astrophysics Data System (ADS)

Han, Kwangsoo; Kahng, Andrew B.; Lee, Hyein; Wang, Lutong

2015-10-01

Self-aligned multiple patterning (SAMP), due to its low overlay error, has emerged as the leading option for 1D gridded back-end-of-line (BEOL) in sub-14nm nodes. To form actual routing patterns from a uniform "sea of wires", a cut mask is needed for line-end cutting or realization of space between routing segments. Constraints on cut shapes and minimum cut spacing result in end-of-line (EOL) extensions and non-functional (i.e. dummy fill) patterns; the resulting capacitance and timing changes must be consistent with signoff performance analyses and their impacts should be minimized. In this work, we address the co-optimization of cut mask layout, dummy fill, and design timing for sub-14nm BEOL design. Our central contribution is an optimizer based on integer linear programming (ILP) to minimize the timing impact due to EOL extensions, considering (i) minimum cut spacing arising in sub-14nm nodes; (ii) cut assignment to different cut masks (color assignment); and (iii) the eligibility to merge two unit-size cuts into a bigger cut. We also propose a heuristic approach to remove dummy fills after the ILP-based optimization by extending the usage of cut masks. Our heuristic can improve critical path performance under minimum metal density and mask density constraints. In our experiments, we study the impact of number of cut masks, minimum cut spacing and metal density under various constraints. Our studies of optimized cut mask solutions in these varying contexts give new insight into the tradeoff of performance and cost that is afforded by cut mask patterning technology options.

Encouraging Democratic Transitions: The Problematic Impact of United States’ Involvement

DTIC Science & Technology

1991-06-20

more abstractly, democracy is consolidated when uncertainty is institutionalized: nobody can control the outcomes of the political process ex post ...for Change in Cuba", Miami Herald, May 27, 1990. See also, Al Kamen, "US Encourages Soviets to Aid Salvadoran Talks". Washington Post , October 18, 1990...Report, September 13, 1990, p. 10, and "Cuba Cuts Fuel Consumption as Soviet Oil Deliveries Fall", Washington Post , August 30, 1990. 20 not even call

Archeological Survey and Testing Along Boone Creek, Louisiana Army Ammunition Plant, Webster Parish, Louisiana

DTIC Science & Technology

1989-01-01

ducks, partridges, cranes , quail, snakes, and fish. 8 CHAPTER 2: ENVIRONMENTAL SETTING Climate The modern climate of the project area is classified as... caustic materials. Large openings in their sides were cut by oil field workers, who then added water to the dry caustic material to make a caustic ...whiffletree hook and a harness ring were recovered, indicating that horses were used here. No automotive artifacts were recovered. This again reinforces the

Dental cutting behaviour of mica-based and apatite-based machinable glass-ceramics.

PubMed

Taira, M; Wakasa, K; Yamaki, M; Matsui, A

1990-09-01

Some recently developed industrial ceramics have excellent machinability properties. The objective of this study was to evaluate the dental cutting behaviour of two machinable glass-ceramics, mica-containing Macor-M and apatite- and diopside-containing Bioram-M, and to compare them with the cutting behaviour of a composite resin typodont tooth enamel and bovine enamel. Weight-load cutting tests were conducted, using a diamond point driven by an air-turbine handpiece, While the transverse load applied on the point was varied, the handpiece speed during cutting and the volume of removal upon cutting were measured. In general, an increase in the applied load caused a decrease in cutting speed and an increase in cutting volume. However, the intensity of this trend was found to differ between four workpieces. Cutting Macor-M resulted in the second-most reduced cutting speed and the maximum cutting volume. Cutting Bioram-M gave the least reduced cutting speed and the minimum cutting volume. It was suggested that two machinable glass-ceramics could be employed as typodont teeth. This study may also contribute to the development of new restorative dental ceramic materials, prepared by machining.

A new method for the prediction of chatter stability lobes based on dynamic cutting force simulation model and support vector machine

NASA Astrophysics Data System (ADS)

Peng, Chong; Wang, Lun; Liao, T. Warren

2015-10-01

Currently, chatter has become the critical factor in hindering machining quality and productivity in machining processes. To avoid cutting chatter, a new method based on dynamic cutting force simulation model and support vector machine (SVM) is presented for the prediction of chatter stability lobes. The cutting force is selected as the monitoring signal, and the wavelet energy entropy theory is used to extract the feature vectors. A support vector machine is constructed using the MATLAB LIBSVM toolbox for pattern classification based on the feature vectors derived from the experimental cutting data. Then combining with the dynamic cutting force simulation model, the stability lobes diagram (SLD) can be estimated. Finally, the predicted results are compared with existing methods such as zero-order analytical (ZOA) and semi-discretization (SD) method as well as actual cutting experimental results to confirm the validity of this new method.

Investigation of biobased and petroleum base oils in the entire spectrum of lubrication regimes

USDA-ARS?s Scientific Manuscript database

The tribological properties of biobased and petroleum-based base oils in the entire lubrication regime were investigated. High oleic sunflower oil (HOSuO) and commercially available polyalphaolefin (PAO-6) were selected to represent biobased and petroleum-based base oils, respectively. These two oil...

CO2 laser cutting of ultra thin (75 μm) glass based rigid optical solar reflector (OSR) for spacecraft application

NASA Astrophysics Data System (ADS)

Mishra, Shubham; Sridhara, N.; Mitra, Avijit; Yougandar, B.; Dash, Sarat Kumar; Agarwal, Sanjay; Dey, Arjun

2017-03-01

Present study reports for the first time laser cutting of multilayered coatings on both side of ultra thin (i.e., 75 μm) glass substrate based rigid optical solar reflector (OSR) for spacecraft thermal control application. The optimization of cutting parameters was carried out as a function of laser power, cutting speed and number of cutting passes and their effect on cutting edge quality. Systematic and in-detail microstructural characterizations were carried out by optical and scanning electron microscopy techniques to study the laser affected zone and cutting edge quality. Sheet resistance and water contact angle experiments were also conducted locally both prior and after laser cut to investigate the changes of electrical and surface properties, if any.

Smart Cutting Tools and Smart Machining: Development Approaches, and Their Implementation and Application Perspectives

NASA Astrophysics Data System (ADS)

Cheng, Kai; Niu, Zhi-Chao; Wang, Robin C.; Rakowski, Richard; Bateman, Richard

2017-09-01

Smart machining has tremendous potential and is becoming one of new generation high value precision manufacturing technologies in line with the advance of Industry 4.0 concepts. This paper presents some innovative design concepts and, in particular, the development of four types of smart cutting tools, including a force-based smart cutting tool, a temperature-based internally-cooled cutting tool, a fast tool servo (FTS) and smart collets for ultraprecision and micro manufacturing purposes. Implementation and application perspectives of these smart cutting tools are explored and discussed particularly for smart machining against a number of industrial application requirements. They are contamination-free machining, machining of tool-wear-prone Si-based infra-red devices and medical applications, high speed micro milling and micro drilling, etc. Furthermore, implementation techniques are presented focusing on: (a) plug-and-produce design principle and the associated smart control algorithms, (b) piezoelectric film and surface acoustic wave transducers to measure cutting forces in process, (c) critical cutting temperature control in real-time machining, (d) in-process calibration through machining trials, (e) FE-based design and analysis of smart cutting tools, and (f) application exemplars on adaptive smart machining.

Surrogate Reservoir Model

NASA Astrophysics Data System (ADS)

Mohaghegh, Shahab

2010-05-01

Surrogate Reservoir Model (SRM) is new solution for fast track, comprehensive reservoir analysis (solving both direct and inverse problems) using existing reservoir simulation models. SRM is defined as a replica of the full field reservoir simulation model that runs and provides accurate results in real-time (one simulation run takes only a fraction of a second). SRM mimics the capabilities of a full field model with high accuracy. Reservoir simulation is the industry standard for reservoir management. It is used in all phases of field development in the oil and gas industry. The routine of simulation studies calls for integration of static and dynamic measurements into the reservoir model. Full field reservoir simulation models have become the major source of information for analysis, prediction and decision making. Large prolific fields usually go through several versions (updates) of their model. Each new version usually is a major improvement over the previous version. The updated model includes the latest available information incorporated along with adjustments that usually are the result of single-well or multi-well history matching. As the number of reservoir layers (thickness of the formations) increases, the number of cells representing the model approaches several millions. As the reservoir models grow in size, so does the time that is required for each run. Schemes such as grid computing and parallel processing helps to a certain degree but do not provide the required speed for tasks such as: field development strategies using comprehensive reservoir analysis, solving the inverse problem for injection/production optimization, quantifying uncertainties associated with the geological model and real-time optimization and decision making. These types of analyses require hundreds or thousands of runs. Furthermore, with the new push for smart fields in the oil/gas industry that is a natural growth of smart completion and smart wells, the need for real time reservoir modeling becomes more pronounced. SRM is developed using the state of the art in neural computing and fuzzy pattern recognition to address the ever growing need in the oil and gas industry to perform accurate, but high speed simulation and modeling. Unlike conventional geo-statistical approaches (response surfaces, proxy models …) that require hundreds of simulation runs for development, SRM is developed only with a few (from 10 to 30 runs) simulation runs. SRM can be developed regularly (as new versions of the full field model become available) off-line and can be put online for real-time processing to guide important decisions. SRM has proven its value in the field. An SRM was developed for a giant oil field in the Middle East. The model included about one million grid blocks with more than 165 horizontal wells and took ten hours for a single run on 12 parallel CPUs. Using only 10 simulation runs, an SRM was developed that was able to accurately mimic the behavior of the reservoir simulation model. Performing a comprehensive reservoir analysis that included making millions of SRM runs, wells in the field were divided into five clusters. It was predicted that wells in cluster one & two are best candidates for rate relaxation with minimal, long term water production while wells in clusters four and five are susceptive to high water cuts. Two and a half years and 20 wells later, rate relaxation results from the field proved that all the predictions made by the SRM analysis were correct. While incremental oil production increased in all wells (wells in clusters 1 produced the most followed by wells in cluster 2, 3 …) the percent change in average monthly water cut for wells in each cluster clearly demonstrated the analytic power of SRM. As it was correctly predicted, wells in clusters 1 and 2 actually experience a reduction in water cut while a substantial increase in water cut was observed in wells classified into clusters 4 and 5. Performing these analyses would have been impossible using the original full field simulation model.

Research on cutting path optimization of sheet metal parts based on ant colony algorithm

NASA Astrophysics Data System (ADS)

Wu, Z. Y.; Ling, H.; Li, L.; Wu, L. H.; Liu, N. B.

2017-09-01

In view of the disadvantages of the current cutting path optimization methods of sheet metal parts, a new method based on ant colony algorithm was proposed in this paper. The cutting path optimization problem of sheet metal parts was taken as the research object. The essence and optimization goal of the optimization problem were presented. The traditional serial cutting constraint rule was improved. The cutting constraint rule with cross cutting was proposed. The contour lines of parts were discretized and the mathematical model of cutting path optimization was established. Thus the problem was converted into the selection problem of contour lines of parts. Ant colony algorithm was used to solve the problem. The principle and steps of the algorithm were analyzed.

Emissions of particulate matter and associated polycyclic aromatic hydrocarbons from agricultural diesel engine fueled with degummed, deacidified mixed crude palm oil blends.

PubMed

Phoungthong, Khamphe; Tekasakul, Surajit; Tekasakul, Perapong; Prateepchaikul, Gumpon; Jindapetch, Naret; Furuuchi, Masami; Hata, Mitsuhiko

2013-04-01

Mixed crude palm oil (MCPO), the mixture of palm fiber oil and palm kernel oil, has become of great interest as a renewable energy source. It can be easily extracted from whole dried palm fruits. In the present work, the degummed, deacidified MCPO was blended in petroleum diesel at portions of 30% and 40% by volume and then tested in agricultural diesel engines for long-term usage. The particulates from the exhaust of the engines were collected every 500 hr using a four-stage cascade air sampler. The 50% cut-off aerodynamic diameters for the first three stages were 10, 2.5 and 1 microm, while the last stage collected all particles smaller than 1 microm. Sixteen particle bounded polycyclic aromatic hydrocarbons (PAHs) were analyzed using a high performance liquid chromatography. The results indicated that the size distribution of particulate matter was in the accumulation mode and the pattern of total PAHs associated with fine-particles (< 1 microm) showed a dominance of larger molecular weight PAHs (4-6 aromatic rings), especially pyrene. The mass median diameter, PM and total PAH concentrations decreased when increasing the palm oil content, but increased when the running hours of the engine were increased. In addition, Commercial petroleum diesel (PB0) gave the highest value of carcinogenic potency equivalent (BaP(eq)) for all particle size ranges. As the palm oil was increased, the BaP(eq) decreased gradually. Therefore the degummed-deacidified MCPO blends are recommended for diesel substitute.

Waulsortian mound development in Warsaw at Broughton field, Ill.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitaker, S.T.

1995-04-17

Oil production in the Lower Mississippian Ullin (Warsaw) limestone was first established in Illinois over 40 years ago. Exploration for hydrocarbons in this zone, however, was limited until recently due to a lack of a suitable explanation for reservoir development in this interval. The theory that Waulsortian mound development may explain many of these reservoirs was first presented in 1990. Research effort led by Zakaria Lasemi at the Illinois State Geological Survey has since established an excellent model for the generation of these bioherms. Lasemi performed numerous examinations of outcrops, cores, and well cuttings to develop his theory on themore » development and evolution of these biohermal features. This article presents an application of Lasemi`s model to an oil field in the Illinois basin. Similar applications could improve exploration and development success in Warsaw reservoirs.« less

Hydrocarbon source potential of the Tanezzuft Formation, Murzuq Basin, south-west Libya: An organic geochemical approach

NASA Astrophysics Data System (ADS)

El Diasty, W. Sh.; El Beialy, S. Y.; Anwari, T. A.; Batten, D. J.

2017-06-01

A detailed organic geochemical study of 20 core and cuttings samples collected from the Silurian Tanezzuft Formation, Murzuq Basin, in the south-western part of Libya has demonstrated the advantages of pyrolysis geochemical methods for evaluating the source-rock potential of this geological unit. Rock-Eval pyrolysis results indicate a wide variation in source richness and quality. The basal Hot Shale samples proved to contain abundant immature to early mature kerogen type II/III (oil-gas prone) that had been deposited in a marine environment under terrigenous influence, implying good to excellent source rocks. Strata above the Hot Shale yielded a mixture of terrigenous and marine type III/II kerogen (gas-oil prone) at the same maturity level as the Hot Shale, indicating the presence of only poor to fair source rocks.

The detection of dissolved gases in transformer oil by gas chromatography with helium ionization detector

NASA Astrophysics Data System (ADS)

Deng, Xian-qin; Fang, Hua; Li, Min-xian

2017-07-01

The GC-PDD with the technology of valve cutting and helium ionization detector was used to analyze the dissolved gases in ultra-high voltage(UHV) and extra-high voltage(EHV) transformer oil. The detection limit(DL) reached ppb grade, especially for the featuring gas—C2H2 and H2, whose DL could reach 5ppb and 11ppb respectively. The test reproducibility of the instrument was about 1% and the correlation coefficient of standard curve-r is greater or equal to 0.99, which showed obvious advantage compared with normal GC. In addition, the auxiliary gas of H2 was not used in this instrument, which completely improved the safety performance. Thus, the application of GC-PDD has significant meaning in warning potential malfunction inside the ultra-high voltage transformer in advance.

Photodiode-based cutting interruption sensor for near-infrared lasers.

PubMed

Adelmann, B; Schleier, M; Neumeier, B; Hellmann, R

2016-03-01

We report on a photodiode-based sensor system to detect cutting interruptions during laser cutting with a fiber laser. An InGaAs diode records the thermal radiation from the process zone with a ring mirror and optical filter arrangement mounted between a collimation unit and a cutting head. The photodiode current is digitalized with a sample rate of 20 kHz and filtered with a Chebyshev Type I filter. From the measured signal during the piercing, a threshold value is calculated. When the diode signal exceeds this threshold during cutting, a cutting interruption is indicated. This method is applied to sensor signals from cutting mild steel, stainless steel, and aluminum, as well as different material thicknesses and also laser flame cutting, showing the possibility to detect cutting interruptions in a broad variety of applications. In a series of 83 incomplete cuts, every cutting interruption is successfully detected (alpha error of 0%), while no cutting interruption is reported in 266 complete cuts (beta error of 0%). With this remarkable high detection rate and low error rate, the possibility to work with different materials and thicknesses in combination with the easy mounting of the sensor unit also to existing cutting machines highlight the enormous potential for this sensor system in industrial applications.

Sensory analysis and consumer acceptance of 140 high-quality extra virgin olive oils.

PubMed

Valli, Enrico; Bendini, Alessandra; Popp, Martin; Bongartz, Annette

2014-08-01

Sensory analysis is a crucial tool for evaluating the quality of extra virgin olive oils. One aim of such an investigation is to verify if the sensory attributes themselves - which are strictly related to volatile and phenolic compounds - may permit the discrimination of high-quality products obtained by olives of different cultivars and/or grown in various regions. Moreover, a crucial topic is to investigate the interdependency between relevant parameters determining consumer acceptance and objective sensory characteristics evaluated by the panel test. By statistically analysing the sensory results, a grouping - but not discriminatory - effect was shown for some cultivars and some producing areas. The preference map shows that the most appreciated samples by consumers were situated in the direction of the 'ripe fruity' and 'sweet' axis and opposite to the 'bitter' and 'other attributes' (pungent, green fruity, freshly cut grass, green tomato, harmony, persistency) axis. Extra virgin olive oils produced from olives of the same cultivars and grown in the same areas shared similar sensorial attributes. Some differences in terms of expectation and interpretation of sensory characteristics of extra virgin olive oils might be present for consumers and panellists: most of the consumers appear unfamiliar with positive sensorial attributes, such as bitterness and pungency. © 2013 Society of Chemical Industry.

Permafrost, heat flow, and the geothermal regime at Prudhoe Bay, Alaska.

USGS Publications Warehouse

Lachenbruch, A.H.; Sass, J.H.; Marshall, B.V.; Moses, T.H.

1982-01-01

Temperature measurements through permafrost in the oil field at Prudhoe Bay, Alaska, combined with laboratory measurements of the thermal conductivity of drill cutting permit an evaluation of in situ thermal properties and an understanding of the general factors that control the geothermal regime. A sharp contrast in temperatire gradient at c600m represents a contrast in thermal conductivity caused by the downward change from interstitial ice to interstitial water at the base of permafrost under near steady state conditions. These results yield a heat flow of c1.3HFU, which is similar to other values on the Alaskan Arctic Coast: the anomalously deep permafrost is a result of the anomalously high conductivity of the siliceous ice-rich sediments. With confirmation of the permafrost configuration by offshore drilling, heat conduction models can yield reliable new information on the chronology of arctic shoreline. -from Authors

Exposure to oil mist and oil vapour during offshore drilling in norway, 1979-2004.

PubMed

Steinsvåg, Kjersti; Bråtveit, Magne; Moen, Bente E

2006-03-01

To describe personal exposure to airborne hydrocarbon contaminants (oil mist and oil vapour) from 1979 to 2004 in the mud-handling areas of offshore drilling facilities operating on the Norwegian continental shelf when drilling with oil-based muds. Qualitative and quantitative information was gathered during visits to companies involved in offshore oil and gas production in Norway. Monitoring reports on oil mist and oil vapour exposure covered 37 drilling facilities. Exposure data were analysed using descriptive statistics and by constructing linear mixed-effects models. Samples had been taken during the use of three generations of hydrocarbon base oils, namely diesel oils (1979-1984), low-aromatic mineral oils (1985-1997) and non-aromatic mineral oils (1998-2004). Sampling done before 1984 showed high exposure to diesel vapour (arithmetic mean, AM = 1217 mg m(-3)). When low-aromatic mineral oils were used, the exposure to oil mist and oil vapour was 4.3 and 36 mg m(-3), and the respective AMs for non-aromatic mineral oils were reduced to 0.54 and 16 mg m(-3). Downward time trends were indicated for both oil mist (6% per year) and oil vapour (8% per year) when the year of monitoring was introduced as a fixed effect in a linear mixed-effects model analysis. Rig type, technical control measures and mud temperature significantly determined exposure to oil mist. Rig type, type of base oil, viscosity of the base oil, work area, mud temperature and season significantly determined exposure to oil vapour. Major decreases in variability were found for the between-rig components. Exposure to oil mist and oil vapour declined over time in the mud-handling areas of offshore drilling facilities. Exposure levels were associated with rig type, mud temperature, technical control measures, base oil, viscosity of the base oil, work area and season.

Thermal regime of permafrost at Prudhoe Bay, Alaska

USGS Publications Warehouse

Lachenbruch, A.H.; Sass, J.H.; Marshall, B.V.; Moses, T.H.

1982-01-01

Temperature measurements through permafrost in the oil field at Prudhoe Bay, Alaska, combined with laboratory measurements of the thermal conductivity of drill cuttings permit an evaluation of in situ thermal properties and an understanding of the general factors that control the geothermal regime. A sharp contrast in temperature gradient at ~600 m represents a contrast in thermal conductivity caused by the downward change from interstitial ice to interstitial water at the base of permafrost under near steady-state conditions. Interpretation of the gradient contrast in terms of a simple model for the conductivity of an aggregate yields the mean ice content and thermal conductivities for the frozen and thawed sections (8.1 and 4.7 mcal/cm sec ?C, respectively). These results yield a heat flow of ~1.3 HFU which is similar to other values on the Alaskan Arctic Coast; the anomalously deep permafrost is a result of the anomalously high conductivity of the siliceous ice-rich sediments. Curvature in the upper 160 m of the temperature profiles represents a warming of ~1.8?C of the mean surface temperature, and a net accumulation of 5-6 kcal/cm 2 by the solid earth surface during the last 100 years or so. Rising sea level and thawing sea cliffs probably caused the shoreline to advance tens of kilometers in the last 20,000 years, inundating a portion of the continental shelf that is presently the target of intensive oil exploration. A simple conduction model suggests that this recently inundated region is underlain by near-melting ice-rich permafrost to depths of 300-500 m; its presence is important to seismic interpretations in oil exploration and to engineering considerations in oil production. With confirmation of the permafrost configuration by offshore drilling, heat-conduction models can yield reliable new information on the chronology of arctic shorelines.

Synthesis and Performance Evaluation of a New Deoiling Agent for Treatment of Waste Oil-Based Drilling Fluids

PubMed Central

Liu, Pingting; Huang, Zhiyu; Deng, Hao; Wang, Rongsha; Xie, Shuixiang

2014-01-01

Oil-based drilling fluid is used more and more in the field of oil and gas exploration. However, because of unrecyclable treating agent and hard treatment conditions, the traditional treating technologies of waste oil-based drilling fluid have some defects, such as waste of resource, bulky equipment, complex treatment processes, and low oil recovery rate. In this work, switchable deoiling agent (SDA), as a novel surfactant for treatment of waste oil-based drilling fluid, was synthesized by amine, formic acid, and formaldehyde solution. With this agent, the waste oil-based drilling fluid can be treated without complex process and expensive equipment. Furthermore, the agent used in the treatment can be recycled, which reduces waste of resource and energy. The switch performance, deoiling performance, structural characterization, and mechanisms of action are studied. The experimental results show that the oil content of the recycled oil is higher than 96% and more than 93% oil in waste oil-based drilling fluid can be recycled. The oil content of the solid residues of deoiling is less than 3%. PMID:25045749

Synthesis and performance evaluation of a new deoiling agent for treatment of waste oil-based drilling fluids.

PubMed

Liu, Pingting; Huang, Zhiyu; Deng, Hao; Wang, Rongsha; Xie, Shuixiang

2014-01-01

Oil-based drilling fluid is used more and more in the field of oil and gas exploration. However, because of unrecyclable treating agent and hard treatment conditions, the traditional treating technologies of waste oil-based drilling fluid have some defects, such as waste of resource, bulky equipment, complex treatment processes, and low oil recovery rate. In this work, switchable deoiling agent (SDA), as a novel surfactant for treatment of waste oil-based drilling fluid, was synthesized by amine, formic acid, and formaldehyde solution. With this agent, the waste oil-based drilling fluid can be treated without complex process and expensive equipment. Furthermore, the agent used in the treatment can be recycled, which reduces waste of resource and energy. The switch performance, deoiling performance, structural characterization, and mechanisms of action are studied. The experimental results show that the oil content of the recycled oil is higher than 96% and more than 93% oil in waste oil-based drilling fluid can be recycled. The oil content of the solid residues of deoiling is less than 3%.

Environmental management in resource-rich Alberta, Canada: first world jurisdiction, Third World analogue?

PubMed

Timoney, K; Lee, P

2001-12-01

Economic growth is frequently touted as a cure for environmental ills, particularly for those in Third World countries. Here we examine that paradigm in a case study of Alberta, Canada, a wealthy, resource-rich province within a wealthy nation. Through provincial-scale datasets, we examine the increasing pressures of the forest, petroleum, and agricultural industries upon the ecosystems of Alberta within management, economic, and political contexts. We advance the thesis that economic activity leads to environmental degradation unless ecosystem-based management is integrated into economic decision making. Agricultural lands cover 31.7%, and forest management areas leased to industry cover 33.4% of Alberta; both continue to increase in extent. The rate of logging (focused on old-growth by government policy) continues a decades-long exponential rise. Current Alberta annual petroleum production is 52.5 million m3 crude oil and 117 billion m3 of gas. As of early 1999, there were approximately 199,025 oil and gas wells and a conservative total of approximately 1.5-1.8 million km of seismic lines in Alberta. Fire occurrence data indicate no downward trends in annual area burned by wildfire, which may be characterized as driven by climate and inherently variable. When logging and wildfire are combined, the annual allowable cut in Alberta is unsustainable, even when only timber supply is considered and the effects of expanding agriculture and oil and gas activities are ignored. Ecosystem degradation in Alberta is pervasive and contrasts prominently with a high standard of living. A wealth of ecological data exists that indicates current resource-based economic activities are non-sustainable and destructive of ecosystem health yet these data are not considered within the economic decision making process. Given the complex, compounded, and increasing ecosystem perturbations, a future of unpleasant ecological surprises is likely. We conclude with tentative predictions as to where current trends in Alberta may lead if decisions biased against ecosystems continue.

Structure of the top of the Karnak Limestone Member (Ste. Genevieve) in Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bristol, H.M.; Howard, R.H.

1976-01-01

To facilitate petroleum exploration in Illinois, the Illinois State Geological Survey presents a structure map (for most of southern Illinois) of the Karnak Limestone Member--a relatively pure persistent limestone unit (generally 10 to 35 ft thick) in the Ste. Genevieve Limestone of Genevievian age. All available electric logs and selected studies of well cuttings were used in constructing the map. Oil and gas development maps containing Karnak-structure contours are on open file at the ISGS.

Geological Data Preservation Program Receives Bipartisan Support

NASA Astrophysics Data System (ADS)

Showstack, Randy

2014-09-01

More than 22 million vertical feet of geologic cores and cuttings fill the Kentucky Geological Survey's Well Sample and Core Library in Lexington. The materials are from at least 22,000 sites within Kentucky—including collections from oil and gas exploration operations, coal and other mining companies, highway construction projects, environmental studies, and federal facilities such as Fort Knox—and they are straining the 15-year-old facility to the point where there is no room to keep everything, according to geologist Patrick Gooding, the library manager.

The Impact of the Arab Decision-Makers on the Oil Market

DTIC Science & Technology

1976-03-01

Libya, United Arab Emirates, Nigeria and the Republic of Gabon. The structure of the Organization con- sists of the following six functioning units...are Cut," Middle East Economic Digest, p„ 1238, 26 October 1973. 65 dollar devaluation . They tempered their resolve by saying that this was not a...demand for higher prices but a desire for a share of the greater profits that companies could now 82make as a result of the devaluation . Since the

Brazil’s National Defense Strategy: Prospects for the Twenty-First Century

DTIC Science & Technology

1993-06-01

also see Everardo Backheuser, Curso de Geopolitica Geral e do Brasil, (Rio de Janeiro: Biblioteca do ’Ex~rcito, 1952). 21 chance of dislocation of the...34, Latin American Weekly Report, 14 January 1993, WR-93-02, 14. 46 virtually irresistible, and the reality is that Brazil is stumbling with its national...cut off Brazil’s primary source of oil. Brazilian arms manufactures, such as EMBRAER, ENGESA, and AVIBRAS, went deep into debt, teetering on virtual

Basic Trends of Frictional Interaction and Tribodiagnostics

DTIC Science & Technology

1996-04-01

control of cutting tool and different type of the .5 bearing are often described as well. There was also a large variety of technical objects studied...in the form of thin flat insert are manufactured from the same steel as objects under control with addition of cobalt (1-2%). Their activation by...additives in oils or greases, as well as if one of the elements of the rubbing pairs is made of a copper-containing alloy, for example steel -bronze pairs

In vitro propagation of olive (Olea europaea L.) by nodal segmentation of elongated shoots.

PubMed

Lambardi, Maurizio; Ozudogru, Elif Aylin; Roncasaglia, Romano

2013-01-01

Olive (Olea europaea L.), long-living, ever-green fruit tree of the Old World, has been part of a traditional landscape in the Mediterranean area for centuries. Both the fruits consumed after processing and the oil extracted from the fruits are among the main components of the Mediterranean diet, widely used for salads and cooking, as well as for preserving other food. Documentations show that the ancient use of this beautiful tree also includes lamp fuel production, wool treatment, soap production, medicine, and cosmetics. However, unlike the majority of the fruit species, olive propagation is still a laborious practice. As regards traditional propagation, rooting of cuttings and grafting stem segments onto rootstocks are possible, former being achieved only when the cuttings are collected in specific periods (spring or beginning of autumn), and latter only when skilled grafters are available. In both the cases, performance of the cultivars varies considerably. The regeneration of whole plants from ovules, on the other hand, is used only occasionally. Micropropagation of olive is not easy mainly due to explant oxidation, difficulties in explant disinfection, and labor-oriented establishment of in vitro shoot cultures. However today, the progress in micropropagation technology has made available the complete protocols for several Mediterranean cultivars. This chapter describes a micropropagation protocol based on the segmentation of nodal segments obtained from elongated shoots.

Devonian salt dissolution-collapse breccias flooring the Cretaceous Athabasca oil sands deposit and development of lower McMurray Formation sinkholes, northern Alberta Basin, Western Canada

NASA Astrophysics Data System (ADS)

Broughton, Paul L.

2013-01-01

The sub-Cretaceous paleotopography underlying giant Lower Cretaceous Athabasca oil sands, northern Alberta, has an orthogonal lattice pattern of troughs up to 50 km long and 100 m deep between pairs of cross-cutting lineaments. These structures are interpreted to have been inherited from a similar pattern of dissolution collapse-subsidence troughs in the underlying Middle Devonian salt beds. Removal of more than 100 m of halite salt fragmented the overlying Upper Devonian strata into fault blocks and collapse breccias that subsided into the underlying dissolution troughs. The unusually low 1:2 to 1:3 thickness ratios of halite salts to the overlying strata resulted in the Upper Devonian strata collapse-subsidence into underlying salt dissolution troughs being more cataclysmic during the first phase of salt removal. The second phase of slower but complete salt removal between the earlier troughs resulted in a more gradual subsidence of the overlying strata. This obliterated the earlier pattern of giant cross-cutting dissolution troughs bounded by major lineaments. The collapse breccia fabrics underlying the earlier troughs differ from those from areas between the troughs. Collapse breccias underlying the large troughs often have crushed fabrics distributed in zones that rapidly pinched out between fault blocks. Breccias between troughs developed as giant mosaics of detached carbonate blocks that formed breccia pipe complexes. Multiple sinkholes up to 100 m deep aligned along multi-km linear valley trends that dissected the sub-Cretaceous paleotopography. These sinkhole trends formed orthogonal patterns inherited from underlying lattice of NW-SE and NE-SW salt structured lineaments. These cross-cutting sinkhole trends have a smaller 5 km scale reticulate pattern similar to the giant 50 km scale pattern of collapse-subsidence troughs. Other sinkholes developed as lower McMurray strata sagged when underlying Devonian fault blocks and breccia pipes differentially subsided.

Diagnosis of edge condition based on force measurement during milling of composites

NASA Astrophysics Data System (ADS)

Felusiak, Agata; Twardowski, Paweł

2018-04-01

The present paper presents comparative results of the forecasting of a cutting tool wear with the application of different methods of diagnostic deduction based on the measurement of cutting force components. The research was carried out during the milling of the Duralcan F3S.10S aluminum-ceramic composite. Prediction of the toolwear was based on one variable, two variables regression Multilayer Perceptron(MLP)and Radial Basis Function(RBF)neural networks. Forecasting the condition of the cutting tool on the basis of cutting forces has yielded very satisfactory results.

Online machining error estimation method of numerical control gear grinding machine tool based on data analysis of internal sensors

NASA Astrophysics Data System (ADS)

Zhao, Fei; Zhang, Chi; Yang, Guilin; Chen, Chinyin

2016-12-01

This paper presents an online estimation method of cutting error by analyzing of internal sensor readings. The internal sensors of numerical control (NC) machine tool are selected to avoid installation problem. The estimation mathematic model of cutting error was proposed to compute the relative position of cutting point and tool center point (TCP) from internal sensor readings based on cutting theory of gear. In order to verify the effectiveness of the proposed model, it was simulated and experimented in gear generating grinding process. The cutting error of gear was estimated and the factors which induce cutting error were analyzed. The simulation and experiments verify that the proposed approach is an efficient way to estimate the cutting error of work-piece during machining process.

Accuracy in planar cutting of bones: an ISO-based evaluation.

PubMed

Cartiaux, Olivier; Paul, Laurent; Docquier, Pierre-Louis; Francq, Bernard G; Raucent, Benoît; Dombre, Etienne; Banse, Xavier

2009-03-01

Computer- and robot-assisted technologies are capable of improving the accuracy of planar cutting in orthopaedic surgery. This study is a first step toward formulating and validating a new evaluation methodology for planar bone cutting, based on the standards from the International Organization for Standardization. Our experimental test bed consisted of a purely geometrical model of the cutting process around a simulated bone. Cuts were performed at three levels of surgical assistance: unassisted, computer-assisted and robot-assisted. We measured three parameters of the standard ISO1101:2004: flatness, parallelism and location of the cut plane. The location was the most relevant parameter for assessing cutting errors. The three levels of assistance were easily distinguished using the location parameter. Our ISO methodology employs the location to obtain all information about translational and rotational cutting errors. Location may be used on any osseous structure to compare the performance of existing assistance technologies.

Site Selection and Resource Allocation of Oil Spill Emergency Base for Offshore Oil Facilities

NASA Astrophysics Data System (ADS)

Li, Yunbin; Liu, Jingxian; Wei, Lei; Wu, Weihuang

2018-02-01

Based on the analysis of the historical data about oil spill accidents in the Bohai Sea, this paper discretizes oil spilled source into a limited number of spill points. According to the probability of oil spill risk, the demand for salvage forces at each oil spill point is evaluated. Aiming at the specific location of the rescue base around the Bohai Sea, a cost-benefit analysis is conducted to determine the total cost of disasters for each rescue base. Based on the relationship between the oil spill point and the rescue site, a multi-objective optimization location model for the oil spill rescue base in the Bohai Sea region is established. And the genetic algorithm is used to solve the optimization problem, and determine the emergency rescue base optimization program and emergency resources allocation ratio.

Substitution of Standard Soybean Oil with Olive Oil-Based Lipid Emulsion in Parenteral Nutrition: Comparison of Vascular, Metabolic, and Inflammatory Effects

PubMed Central

Siqueira, Joselita; Smiley, Dawn; Newton, Christopher; Le, Ngoc-Anh; Gosmanov, Aidar R.; Spiegelman, Ronnie; Peng, Limin; Osteen, Samantha J.; Jones, Dean P.; Quyyumi, Arshed A.; Ziegler, Thomas R.

2011-01-01

Context: Soybean oil-based lipid emulsions are the only Food and Drug Administration-approved lipid formulation for clinical use in parenteral nutrition (PN). Recently concerns with its use have been raised due to the proinflammatory effects that may lead to increased complications because they are rich in ω-6 polyunsaturated fatty acids. Methods: This was a prospective, randomized, controlled, crossover study comparing the vascular, metabolic, immune, and inflammatory effects of 24-h infusion of PN containing soybean oil-based lipid emulsion (Intralipid), olive oil-based (ClinOleic), lipid free, and normal saline in 12 healthy subjects. Results: Soybean oil-PN increased systolic blood pressure compared with olive oil-PN (P < 0.05). Soybean oil PN reduced brachial artery flow-mediated dilatation from baseline (−23% at 4 h and −25% at 24 h, both P < 0.01); in contrast, olive oil PN, lipid free PN, and saline did not change either systolic blood pressure or flow-mediated dilatation. Compared with saline, soybean oil PN, olive oil PN, and lipid free PN similarly increased glucose and insulin concentrations during infusion (P < 0.05). There were no significant changes in plasma free fatty acids, lipid profile, inflammatory and oxidative stress markers, immune function parameters, or sympathetic activity between soybean oil- and olive oil-based lipid emulsions. Conclusion: The 24-h infusion of PN containing soybean oil-based lipid emulsion increased blood pressure and impaired endothelial function compared with PN containing olive oil-based lipid emulsion and lipid-free PN in healthy subjects. These vascular changes may have significant implications in worsening outcome in subjects receiving nutrition support. Randomized controlled trials with relevant clinical outcome measures are needed in patients receiving PN with olive oil-based and soybean oil-based lipid emulsions. PMID:21832112

40 CFR 446.10 - Applicability; description of the oil-base solvent wash paint subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.10 Applicability; description of the oil-base... the production of oil-base paint where the tank cleaning is performed using solvents. When a plant is... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the oil...

40 CFR 446.10 - Applicability; description of the oil-base solvent wash paint subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.10 Applicability; description of the oil-base... the production of oil-base paint where the tank cleaning is performed using solvents. When a plant is... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the oil...

40 CFR 446.10 - Applicability; description of the oil-base solvent wash paint subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.10 Applicability; description of the oil-base... the production of oil-base paint where the tank cleaning is performed using solvents. When a plant is... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the oil...

40 CFR Appendix 7 to Subpart A of... - Determination of the Amount of Non-Aqueous Drilling Fluid (NAF) Base Fluid From Drill Cuttings by...

Code of Federal Regulations, 2013 CFR

2013-07-01

... multiplying the density of the small volume NAF-cuttings discharges (ρsvd) times the volume of the small...-cuttings discharges (kg) ρsvd = density of the small volume NAF-cuttings discharges (kg/bbl) VSVD = volume of the small volume NAF-cuttings discharges (bbl) The density of the small volume NAF-cuttings...

40 CFR Appendix 7 to Subpart A of... - Determination of the Amount of Non-Aqueous Drilling Fluid (NAF) Base Fluid From Drill Cuttings by...

Code of Federal Regulations, 2014 CFR

2014-07-01

... multiplying the density of the small volume NAF-cuttings discharges (ρsvd) times the volume of the small...-cuttings discharges (kg) ρsvd = density of the small volume NAF-cuttings discharges (kg/bbl) VSVD = volume of the small volume NAF-cuttings discharges (bbl) The density of the small volume NAF-cuttings...

40 CFR Appendix 7 to Subpart A of... - Determination of the Amount of Non-Aqueous Drilling Fluid (NAF) Base Fluid From Drill Cuttings by...

Code of Federal Regulations, 2012 CFR

2012-07-01

... multiplying the density of the small volume NAF-cuttings discharges (ρsvd) times the volume of the small...-cuttings discharges (kg) ρsvd = density of the small volume NAF-cuttings discharges (kg/bbl) VSVD = volume of the small volume NAF-cuttings discharges (bbl) The density of the small volume NAF-cuttings...

Predicting the Performance of Chain Saw Machines Based on Shore Scleroscope Hardness

NASA Astrophysics Data System (ADS)

Tumac, Deniz

2014-03-01

Shore hardness has been used to estimate several physical and mechanical properties of rocks over the last few decades. However, the number of researches correlating Shore hardness with rock cutting performance is quite limited. Also, rather limited researches have been carried out on predicting the performance of chain saw machines. This study differs from the previous investigations in the way that Shore hardness values (SH1, SH2, and deformation coefficient) are used to determine the field performance of chain saw machines. The measured Shore hardness values are correlated with the physical and mechanical properties of natural stone samples, cutting parameters (normal force, cutting force, and specific energy) obtained from linear cutting tests in unrelieved cutting mode, and areal net cutting rate of chain saw machines. Two empirical models developed previously are improved for the prediction of the areal net cutting rate of chain saw machines. The first model is based on a revised chain saw penetration index, which uses SH1, machine weight, and useful arm cutting depth as predictors. The second model is based on the power consumed for only cutting the stone, arm thickness, and specific energy as a function of the deformation coefficient. While cutting force has a strong relationship with Shore hardness values, the normal force has a weak or moderate correlation. Uniaxial compressive strength, Cerchar abrasivity index, and density can also be predicted by Shore hardness values.

High performance cutting of aircraft and turbine components

NASA Astrophysics Data System (ADS)

Krämer, A.; Lung, D.; Klocke, F.

2012-04-01

Titanium and nickel-based alloys belong to the group of difficult-to-cut materials. The machining of these high-temperature alloys is characterized by low productivity and low process stability as a result of their physical and mechanical properties. Major problems during the machining of these materials are low applicable cutting speeds due to excessive tool wear, long machining times, and thus high manufacturing costs, as well as the formation of ribbon and snarled chips. Under these conditions automation of the production process is limited. This paper deals with strategies to improve machinability of titanium and nickel-based alloys. Using the example of the nickel-based alloy Inconel 718 high performance cutting with advanced cutting materials, such as PCBN and cutting ceramics, is presented. Afterwards the influence of different cooling strategies, like high-pressure lubricoolant supply and cryogenic cooling, during machining of TiAl6V4 is shown.

A logic-based method for integer programming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooker, J.; Natraj, N.R.

1994-12-31

We propose a logic-based approach to integer programming that replaces traditional branch-and-cut techniques with logical analogs. Integer variables are regarded as atomic propositions. The constraints give rise to logical formulas that are analogous to separating cuts. No continuous relaxation is used. Rather, the cuts are selected so that they can be easily solved as a discrete relaxation. (In fact, defining a relaxation and generating cuts are best seen as the same problem.) We experiment with relaxations that have a k-tree structure and can be solved by nonserial dynamic programming. We also present logic-based analogs of facet-defining cuts, Chv{acute a}tal rank,more » etc. We conclude with some preliminary computational results.« less

Toxicity assessment in marine sediment for the Terra Nova environmental effects monitoring program (1997-2010)

NASA Astrophysics Data System (ADS)

Whiteway, Sandra A.; Paine, Michael D.; Wells, Trudy A.; DeBlois, Elisabeth M.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Janes, G. Gregory

2014-12-01

This paper discusses toxicity test results on sediments from the Terra Nova offshore oil development. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland (Canada). The amphipod (Rhepoxynius abronius) survival and solid phase luminescent bacteria (Vibrio fischeri, or Microtox) assays were conducted on sediment samples collected from approximately 50 stations per program year around Terra Nova during baseline (1997), prior to drilling, and in 2000, 2001, 2002, 2004, 2006, 2008 and 2010 after drilling began. The frequency of toxic responses in the amphipod toxicity test was low. Of the ten stations that were toxic in environmental effects monitoring (EEM) years, only one (station 30(FE)) was toxic in more than one year and could be directly attributed to Terra Nova project activities. In contrast, 65 (18%) of 364 EEM samples were toxic to Microtox. Microtox toxicity in EEM years was not related to distance from Terra Nova drill centres or concentrations of >C10-C21 hydrocarbons or barium, the primary constituents of the synthetic-based drill muds used at Terra Nova. Of the variables tested, fines and strontium levels showed the strongest (positive) correlations with toxicity. Neither fines nor strontium levels were affected by drill cuttings discharge at Terra Nova, except at station 30(FE) (and that station was not toxic to Microtox). Benthic macro-invertebrate abundance, richness and diversity were greater in toxic than in non-toxic sediments. Therefore, Microtox responses indicating toxicity were associated with positive biological responses in the field. This result may have been an indirect function of the increased abundance of most invertebrate taxa in less sandy sediments with higher gravel content, where fines and strontium levels and, consequently, toxicity to Microtox were high; or chemical substances released by biodegradation of organic matter, where invertebrates are abundant, may be toxic to Microtox. Given the lack of association between Microtox results and discharge from Terra Nova, coupled with the confounding effects of other variables, the usefulness of Microtox toxicity tests within the context of environmental monitoring for the Terra Nova and, potentially, other offshore oil operations needs to be questioned. The amphipod toxicity tests showed that sediments in the vicinity of discharges of synthetic-based drilling mud cuttings are rarely toxic.

Rock Drilling Performance Evaluation by an Energy Dissipation Based Rock Brittleness Index

NASA Astrophysics Data System (ADS)

Munoz, H.; Taheri, A.; Chanda, E. K.

2016-08-01

To reliably estimate drilling performance both tool-rock interaction laws along with a proper rock brittleness index are required to be implemented. In this study, the performance of a single polycrystalline diamond compact (PDC) cutter cutting and different drilling methods including PDC rotary drilling, roller-cone rotary drilling and percussive drilling were investigated. To investigate drilling performance by rock strength properties, laboratory PDC cutting tests were performed on different rocks to obtain cutting parameters. In addition, results of laboratory and field drilling on different rocks found elsewhere in literature were used. Laboratory and field cutting and drilling test results were coupled with values of a new rock brittleness index proposed herein and developed based on energy dissipation withdrawn from the complete stress-strain curve in uniaxial compression. To quantify cutting and drilling performance, the intrinsic specific energy in rotary-cutting action, i.e. the energy consumed in pure cutting action, and drilling penetration rate values in percussive action were used. The results show that the new energy-based brittleness index successfully describes the performance of different cutting and drilling methods and therefore is relevant to assess drilling performance for engineering applications.

Visual pigments, oil droplets, lens, and cornea characterization in the whooping crane (Grus americana)

USGS Publications Warehouse

Porter, Megan L.; Kingston, Alexandra C. N.; McCready, Robert; Cameron, Evan G.; Hofmann, Christopher M.; Suarez, Lauren; Olsen, Glenn H.; Cronin, Thomas W.; Robinson, Phyllis R.

2014-01-01

Vision has been investigated in many species of birds, but few studies have considered the visual systems of large birds and the particular implications of large eyes and long-life spans on visual system capabilities. To address these issues we investigated the visual system of the whooping crane, Grus americana (Gruiformes: Gruidae). G. americana (an endangered species) is one of only two North American crane species and represents a large, long-lived bird where ultraviolet sensitivity may be degraded by chromatic aberrations and entrance of ultraviolet light into the eye could be detrimental to retinal tissues. To investigate the whooping crane visual system we used microspectrophotometry to determine the absorbance spectra of retinal oil droplets and to investigate if the ocular media (i.e., the lens and cornea) absorbs UV light. In vitro expression and reconstitution was used to determine the absorbance spectra of rod and cone visual pigments. The rod visual pigments had wavelengths of peak absorbance (λmax) at 500 nm, while the cone visual pigments λmax values were determined to be 404 nm (SWS1), 450 nm (SWS2), 499 nm (RH2), and 561 nm (LWS), similar to other characterized bird visual pigment absorbance values. The oil droplet cutoff wavelength (λcut) values similarly fell within ranges recorded from other avian species: 576 nm (R-type), 522 nm (Y-type), 506 nm (P-type), and 448 nm (C-type). We confirm that G. americana has a violet-sensitive visual system, although based on the λmax of the SWS1 visual pigment (404 nm) may also have some ability for UV sensitivity.

Petroleum mineral oil refining and evaluation of cancer hazard.

PubMed

Mackerer, Carl R; Griffis, Larry C; Grabowski, John S; Reitman, Fred A

2003-11-01

Petroleum base oils (petroleum mineral oils) are manufactured from crude oils by vacuum distillation to produce several distillates and a residual oil that are then further refined. Aromatics including alkylated polycyclic aromatic compounds (PAC) are undesirable constituents of base oils because they are deleterious to product performance and are potentially carcinogenic. In modern base oil refining, aromatics are reduced by solvent extraction, catalytic hydrotreating, or hydrocracking. Chronic exposure to poorly refined base oils has the potential to cause skin cancer. A chronic mouse dermal bioassay has been the standard test for estimating carcinogenic potential of mineral oils. The level of alkylated 3-7-ring PAC in raw streams from the vacuum tower must be greatly reduced to render the base oil noncarcinogenic. The processes that can reduce PAC levels are known, but the operating conditions for the processing units (e.g., temperature, pressure, catalyst type, residence time in the unit, unit engineering design, etc.) needed to achieve adequate PAC reduction are refinery specific. Chronic dermal bioassays provide information about whether conditions applied can make a noncarcinogenic oil, but cannot be used to monitor current production for quality control or for conducting research or developing new processes since this test takes at least 78 weeks to conduct. Three short-term, non-animal assays all involving extraction of oil with dimethylsulfoxide (DMSO) have been validated for predicting potential carcinogenic activity of petroleum base oils: a modified Ames assay of a DMSO extract, a gravimetric assay (IP 346) for wt. percent of oil extracted into DMSO, and a GC-FID assay measuring 3-7-ring PAC content in a DMSO extract of oil, expressed as percent of the oil. Extraction with DMSO concentrates PAC in a manner that mimics the extraction method used in the solvent refining of noncarcinogenic oils. The three assays are described, data demonstrating the validation of the assays are shown, and test results of currently manufactured base oils are summarized to illustrate the general lack of cancer hazard for the base oils now being manufactured.

Toxicological evaluation of Tetracarpidium conophorum nut oil-based diet in rats.

PubMed

Oladiji, A T; Abodunrin, T P; Yakubu, M T

2010-03-01

The effects of Tetracarpidium conophorum nut oil-based diet on the growth performance and some biochemical constituents of rat tissues was investigated following a feeding period of 6 weeks. The results revealed that the volume of water taken, the amount of feed consumed and the weight gained by the animals maintained on the nut oil-based diet were not significantly (P>0.05) different from those fed on soybean oil-based diet. The reduction in the activities of ALP, GOT and GPT in the liver and heart of animals fed on the nut oil-based diet was accompanied by increase in the serum enzymes. The nut oil-based diet significantly reduced (P<0.05) serum concentrations of total cholesterol and HDL-C whereas triglycerides and atherogenic index increased. The serum LDL-C level of the nut oil-based diet fed animals compared well with those of soybean oil-based diet. These alterations suggested that adverse effects have occurred, possibly by altered membrane permeability of the hepatocytes and cardiac cells. Similar alterations in the serum lipids of animals maintained on nut oil-based diet also portends cardiovascular risk. Although, T. conophorum nut oil did not adversely affect growth performance and the feeding appetite of the animals, it is not completely 'safe' for consumption. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Catalytic two-stage coal hydrogenation process using extinction recycle of heavy liquid fraction

DOEpatents

MacArthur, J.B.; Comolli, A.G.; McLean, J.B.

1989-10-17

A process is described for catalytic two-stage hydrogenation and liquefaction of coal with selective extinction recycle of all heavy liquid fractions boiling above a distillation cut point of about 600--750 F to produce increased yields of low-boiling hydrocarbon liquid and gas products. In the process, the particulate coal feed is slurried with a process-derived liquid solvent normally boiling above about 650 F and fed into a first stage catalytic reaction zone operated at conditions which promote controlled rate liquefaction of the coal, while simultaneously hydrogenating the hydrocarbon recycle oils. The first stage reactor is maintained at 710--800 F temperature, 1,000--4,000 psig hydrogen partial pressure, and 10-90 lb/hr per ft[sup 3] catalyst space velocity. Partially hydrogenated material withdrawn from the first stage reaction zone is passed directly to the second stage catalytic reaction zone maintained at 760--860 F temperature for further hydrogenation and hydroconversion reactions. A 600--750 F[sup +] fraction containing 0--20 W % unreacted coal and ash solids is recycled to the coal slurrying step. If desired, the cut point lower boiling fraction can be further catalytically hydrotreated. By this process, the coal feed is successively catalytically hydrogenated and hydroconverted at selected conditions, to provide significantly increased yields of desirable low-boiling hydrocarbon liquid products and minimal production of hydrocarbon gases, and no net production of undesirable heavy oils and residuum materials. 2 figs.

Catalytic two-stage coal hydrogenation process using extinction recycle of heavy liquid fraction

DOEpatents

MacArthur, James B.; Comolli, Alfred G.; McLean, Joseph B.

1989-01-01

A process for catalytic two-stage hydrogenation and liquefaction of coal with selective extinction recycle of all heavy liquid fractions boiling above a distillation cut point of about 600.degree.-750.degree. F. to produce increased yields of low-boiling hydrocarbon liquid and gas products. In the process, the particulate coal feed is slurried with a process-derived liquid solvent normally boiling above about 650.degree. F. and fed into a first stage catalytic reaction zone operated at conditions which promote controlled rate liquefaction of the coal, while simultaneously hydrogenating the hydrocarbon recycle oils. The first stage reactor is maintained at 710.degree.-800.degree. F. temperature, 1000-4000 psig hydrogen partial pressure, and 10-90 lb/hr per ft.sup.3 catalyst space velocity. Partially hydrogenated material withdrawn from the first stage reaction zone is passed directly to the second stage catalytic reaction zone maintained at 760.degree.-860.degree. F. temperature for further hydrogenation and hydroconversion reactions. A 600.degree.-750.degree. F..sup.+ fraction containing 0-20 W % unreacted coal and ash solids is recycled to the coal slurrying step. If desired, the cut point lower boiling fraction can be further catalytically hydrotreated. By this process, the coal feed is successively catalytically hydrogenated and hydroconverted at selected conditions, to provide significantly increased yields of desirable low-boiling hydrocarbon liquid products and minimal production of hydrocarbon gases, and no net production of undesirable heavy oils and residuum materials.

Ekofisk waterflood pilot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, L.K.; Dixon, T.N.; Evans, C.E.

1987-02-01

This paper describes the evaluation of a waterflood pilot in the highly fractured Maastrichtian reservoir of the Ekofisk field in the Norwegian sector of the North Sea. A four-well pilot consisting of one water injector and three producers was initiated in Spring 1981 and was concluded in mid-1984. A total of 21 x 10/sup 6/ bbl(3.3 x 10/sup 6/ m/sup 3/) of water was injected, and water breakthrough occurred in two of the production wells. Simulation of waterflood performance in the pilot was conducted with a three-dimensional (3D), three-phase dual-porosity model. Initial and boundary conditions were taken from a fullmore » 3D single-porosity model of the reservoir. The pilot was conducted to determine the following information for the Maastrichtian: water-cut performance vs. time, water imbibition characteristics, and anisotropy. Results from this work have been incorporated into a full-field waterflood study. Reservoir description included the determination of fractured areas, matrix block sizes, water/oil capillary imbibition, matrix permeability and porosity, and effective permeability. These data were derived from fracture core analysis, pressure transient tests, laboratory water/oil imbibition studies, repeat formation pressure test results, and open- and cased-hole logs. An excellent match of waterflood performance was obtained with the dual-porosity model. Of particular interest are the imbibition characteristics of the Maastrichtian in the Ekofisk field and the character of the water-cut performance of the producing wells following injector shutdowns and startups.« less

Subtask – CO 2 storage and enhanced bakken recovery research program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sorensen, James; Hawthorne, Steven; Smith, Steven

Small improvements in productivity could increase technically recoverable oil in the Bakken Petroleum System by billions of barrels. The use of CO 2 for enhanced oil recovery (EOR) in tight oil reservoirs is a relatively new concept. The large-scale injection of CO 2 into the Bakken would also result in the geological storage of significant amounts of CO 2. The Energy & Environmental Research Center (EERC) has conducted laboratory and modeling activities to examine the potential for CO 2 storage and EOR in the Bakken. Specific activities included the characterization and subsequent modeling of North Dakota study areas as wellmore » as dynamic predictive simulations of possible CO 2 injection schemes to predict the potential CO 2 storage and EOR in those areas. Laboratory studies to evaluate the ability of CO 2 to remove hydrocarbons from Bakken rocks and determine minimum miscibility pressures for Bakken oil samples were conducted. Data from a CO 2 injection test conducted in the Elm Coulee area of Montana in 2009 were evaluated with an eye toward the possible application of knowledge gained to future injection tests in other areas. A first-order estimation of potential CO 2 storage capacity in the Bakken Formation in North Dakota was also conducted. Key findings of the program are as follows. The results of the research activities suggest that CO 2 may be effective in enhancing the productivity of oil from the Bakken and that the Bakken may hold the ability to geologically store between 120 Mt and 3.2 Gt of CO 2. However, there are no clear-cut answers regarding the most effective approach for using CO 2 to improve oil productivity or the storage capacity of the Bakken. The results underscore the notion that an unconventional resource will likely require unconventional methods of both assessment and implementation when it comes to the injection of CO 2. In particular, a better understanding of the fundamental mechanisms controlling the interactions between CO 2, oil, and other reservoir fluids in these unique formations is necessary to develop accurate assessments of potential CO 2 storage and EOR in the Bakken. In addition, existing modeling and simulation software packages do not adequately address or incorporate the unique properties of these tight, unconventional reservoirs in terms of their impact on CO 2 behavior. These knowledge gaps can be filled by conducting scaled-up laboratory activities integrated with improved modeling and simulation techniques, the results of which will provide a robust foundation for pilot-scale field injection tests. Finally, field-based data on injection, fluid production, and long-term monitoring from pilot-scale CO 2 injection tests in the Bakken are necessary to verify and validate the findings of the laboratory- and modeling-based research efforts. This subtask was funded through the EERC–U.S. Department of Energy (DOE) Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FC26-08NT43291. Nonfederal funding was provided by the North Dakota Industrial Commission, Marathon Oil Corporation, Continental Resources Inc., and TAQA North, Ltd.« less

Dielectric breakdown strength of magnetic nanofluid based on insulation oil after impulse test

NASA Astrophysics Data System (ADS)

Nazari, M.; Rasoulifard, M. H.; Hosseini, H.

2016-02-01

In this study, the dielectric breakdown strength of magnetic nanofluids based on transformer mineral oil for use in power systems is reviewed. Nano oil samples are obtained from dispersion of the magnetic nanofluid within uninhibited transformer mineral oil NYTRO LIBRA as the base fluid. AC dielectric breakdown voltage measurement was carried out according to IEC 60156 standard and the lightning impulse breakdown voltage was obtained by using the sphere-sphere electrodes in an experimental setup for nano oil in volume concentration of 0.1-0.6%. Results indicate improved AC and lightning impulse breakdown voltage of nano oil compared to the base oil. AC test was performed again after applying impulse current and result showed that nano oil unlike the base oil retains its dielectric properties. Increase the dielectric strength of the nano oil is mainly due to dielectric and magnetic properties of Fe3O4 nanoparticles that act as free electrons snapper, and reduce the rate of free electrons in the ionization process.

Sequencing of Dust Filter Production Process Using Design Structure Matrix (DSM)

NASA Astrophysics Data System (ADS)

Sari, R. M.; Matondang, A. R.; Syahputri, K.; Anizar; Siregar, I.; Rizkya, I.; Ursula, C.

2018-01-01

Metal casting company produces machinery spare part for manufactures. One of the product produced is dust filter. Most of palm oil mill used this product. Since it is used in most of palm oil mill, company often have problems to address this product. One of problem is the disordered of production process. It carried out by the job sequencing. The important job that should be solved first, least implement, while less important job and could be completed later, implemented first. Design Structure Matrix (DSM) used to analyse and determine priorities in the production process. DSM analysis is sort of production process through dependency sequencing. The result of dependency sequences shows the sequence process according to the inter-process linkage considering before and after activities. Finally, it demonstrates their activities to the coupled activities for metal smelting, refining, grinding, cutting container castings, metal expenditure of molds, metal casting, coating processes, and manufacture of molds of sand.

Calibration and field application of a Sierra Model 235 cascade impactor.

PubMed

Knuth, R H

1984-06-01

A Sierra Model 235 slotted impactor was used to measure the particle size distribution of ore dust in uranium concentrating mills. The impactor was calibrated at a flow rate of 0.21 m3/min, using solid monodisperse particles of methylene blue and an impaction surface of Whatman #41 filter paper soaked in mineral oil. The reduction from the impactor's design flow rate of 1.13 m3/min (40 cfm) to 0.21 m3/min (7.5 cfm), a necessary adjustment because of the anticipated large particles sizes of ore dust, increased the stage cut-off diameters by an average factor of 2.3. Evaluation of field test results revealed that the underestimation of mass median diameters, often caused by the rebound and reentrainment of solid particles from dry impaction surfaces, was virtually eliminated by using the oiled Whatman #41 impaction surface.

Some Factors Affecting the Reproducibility of Penetration and the Cut-Off of Oil Sprays for Fuel-injection Engines

NASA Technical Reports Server (NTRS)

Beardsley, E G

1928-01-01

This investigation was undertaken at the Langley Memorial Aeronautical Laboratory in connection with a general research on fuel-injection for aircraft. The purpose of the investigation was to determine the factors controlling the reproducibility of spray penetration and secondary discharges after cut-off. The development of single sprays from automatic injection valves was recorded by means of special high-speed photographic apparatus capable of taking 25 consecutive pictures of the moving spray at a rate of 4,000 per second. The effect of two types of injection valves, injection-valve tube length, initial pressure in the injection-valve tube, speed of the injection control mechanism, and time of spray cut-off, on the reproducibility of spray penetration, and on secondary discharges were investigated. It was found that neither type of injection valve materially affected spray reproducibility. The initial pressure in the injection-valve tube controlled the reproducibility of spray penetrations. An increase in the initial pressure or in the length of the injection-valve tube slightly increased the spray penetration within the limits of this investigation. The speed of the injection-control mechanism did not affect the penetration. Analysis of the results indicates that secondary discharges were caused in this apparatus by pressure waves initiated by the rapid opening of the cut-off valve. The secondary discharges were eliminated in this investigation by increasing the length of the injection-valve tube. (author)

A micro-scale cutting model for UD CFRP composites with thermo-mechanical coupling

DOE PAGES

Cheng, Hui; Gao, Jiaying; Kafka, Orion Landauer; ...

2017-09-23

Cutting a unidirectional carbon fiber-reinforced polymer (UD CFRP) structure is the basic unit for CFRP machining, which is a complex thermal-mechanically coupled process. To reveal the deformation mechanism and predict cutting force in UD CFRP micro cutting, a micro-scale fracture model for UD CFRP cutting with thermal-mechanical coupling is demonstrated in this paper, which captures the failure modes for fibers, matrix and the interface based on a micro-level RVE using a relatively simple damage based fracture method. The thermal-mechanical coupling model at the micro scale is developed on the basis of the plastic energy dissipation and frictional heating during cutting.more » Failure models for the fiber, matrix and interface region are applied depending on the material properties of each of these three phases. Numerical simulations based on the above model with different fiber orientations were performed to predict the deformation and forces of different components in UD CFRP. Cutting experiments with the same fiber orientations as considered in the simulations were carried out to validate the force and deformation results. The predicted force and deformation patterns match well with evidence from our experiments. In general, the cutting force is larger than the thrust force regardless of fiber orientation. The cutting force reaches a maximum as the fiber orientation approaches 90 , but thrust forces do not vary substantially across cases. When the fiber orientation is acute, the deformation of fibers is much smaller than when the cutting angle is obtuse. Surface roughness follows the same trend with cutting angle as fiber deformation.« less

A micro-scale cutting model for UD CFRP composites with thermo-mechanical coupling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Hui; Gao, Jiaying; Kafka, Orion Landauer

Cutting a unidirectional carbon fiber-reinforced polymer (UD CFRP) structure is the basic unit for CFRP machining, which is a complex thermal-mechanically coupled process. To reveal the deformation mechanism and predict cutting force in UD CFRP micro cutting, a micro-scale fracture model for UD CFRP cutting with thermal-mechanical coupling is demonstrated in this paper, which captures the failure modes for fibers, matrix and the interface based on a micro-level RVE using a relatively simple damage based fracture method. The thermal-mechanical coupling model at the micro scale is developed on the basis of the plastic energy dissipation and frictional heating during cutting.more » Failure models for the fiber, matrix and interface region are applied depending on the material properties of each of these three phases. Numerical simulations based on the above model with different fiber orientations were performed to predict the deformation and forces of different components in UD CFRP. Cutting experiments with the same fiber orientations as considered in the simulations were carried out to validate the force and deformation results. The predicted force and deformation patterns match well with evidence from our experiments. In general, the cutting force is larger than the thrust force regardless of fiber orientation. The cutting force reaches a maximum as the fiber orientation approaches 90 , but thrust forces do not vary substantially across cases. When the fiber orientation is acute, the deformation of fibers is much smaller than when the cutting angle is obtuse. Surface roughness follows the same trend with cutting angle as fiber deformation.« less

Oil and gas geochemistry and petroleum systems of the Fort Worth Basin

USGS Publications Warehouse

Hill, R.J.; Jarvie, D.M.; Zumberge, J.; Henry, M.; Pollastro, R.M.

2007-01-01

Detailed biomarker and light hydrocarbon geochemistry confirm that the marine Mississippian Barnett Shale is the primary source rock for petroleum in the Fort Worth Basin, north-central Texas, although contributions from other sources are possible. Biomarker data indicate that the main oil-generating Barnett Shale facies is marine and was deposited under dysoxic, strong upwelling, normal salinity conditions. The analysis of two outcrop samples and cuttings from seven wells indicates variability in the Barnett Shale organic facies and a possibility of other oil subfamilies being present. Light hydrocarbon analyses reveal significant terrigenous-sourced condensate input to some reservoirs, resulting in terrigenous and mixed marine-terrigenous light hydrocarbon signatures for many oils. The light hydrocarbon data suggest a secondary, condensate-generating source facies containing terrigenous or mixed terrigenous-marine organic matter. This indication of a secondary source rock that is not revealed by biomarker analysis emphasizes the importance of integrating biomarker and light hydrocarbon data to define petroleum source rocks. Gases in the Fort Worth Basin are thermogenic in origin and appear to be cogenerated with oil from the Barnett Shale, although some gas may also originate by oil cracking. Isotope data indicate minor contribution of biogenic gas. Except for reservoirs in the Pennsylvanian Bend Group, which contain gases spanning the complete range of observed maturities, the gases appear to be stratigraphically segregated, younger reservoirs contain less mature gas, and older reservoirs contain more mature gas. We cannot rule out the possibility that other source units within the Fort Worth Basin, such as the Smithwick Shale, are locally important petroleum sources. Copyright ?? 2007. The American Association of Petroleum Geologists. All rights reserved.

Determining BMI cut points based on excess percent body fat in US children and adolescents

USDA-ARS?s Scientific Manuscript database

Current cut points for overweight were derived statistically from BMI distribution. The study aimed at determining age-, gender-, and ethnic-specific BMI cut points based on excess body fat in US children and adolescents aged 8-17 years, who participated in the National Health and Nutrition Examinat...

Long-term effect of fee-for-service-based reimbursement cuts on processes and outcomes of care for stroke: interrupted time-series study from Taiwan.

PubMed

Tung, Yu-Chi; Chang, Guann-Ming; Cheng, Shou-Hsia

2015-01-01

As healthcare spending continues to increase, reimbursement cuts have become 1 type of healthcare reform to contain costs. Little is known about the long-term impact of cuts in reimbursement, especially under a global budget cap with fee-for-service (FFS) reimbursement, on processes and outcomes of care. The FFS-based reimbursement cuts have been implemented since July 2002 in Taiwan. We examined the long-term association of FFS-based reimbursement cuts with trends in processes and outcomes of care for stroke. We analyzed all 411,487 patients with stroke admitted to general acute care hospitals in Taiwan during the period 1997 to 2010 through Taiwan's National Health Insurance Research Database. We used a quasi-experimental design with quarterly measures of healthcare utilization and outcomes and used segmented autoregressive integrated moving average models for the analysis. After accounting for secular trends and other confounders, the implementation of the FFS-based reimbursement cuts was associated with trend changes in computed tomography/magnetic resonance imaging scanning (0.31% per quarter; P=0.013), antiplatelet/anticoagulant use (-0.20% per quarter; P<0.001), statin use (0.18% per quarter; P=0.027), physiotherapy/occupational therapy assessment (0.25% per quarter; P<0.001), and 30-day mortality (0.06% per quarter; P<0.001). There are improvement trends in processes and outcomes of care over time. However, the reimbursement cuts from the FFS-based global budget cap are associated with trend changes in processes and outcomes of care for stroke. The FFS-based reimbursement cuts may have long-term positive and negative associations with stroke care. © 2014 American Heart Association, Inc.

Celluclast 1.5L pretreatment enhanced aroma of palm kernels and oil after kernel roasting.

PubMed

Zhang, Wencan; Zhao, Fangju; Yang, Tiankui; Zhao, Feifei; Liu, Shaoquan

2017-12-01

The aroma of palm kernel oil (PKO) affects its applications. Little information is available on how enzymatic modification of palm kernels (PK) affects PK and PKO aroma after kernel roasting. Celluclast (cellulase) pretreatment of PK resulted in a 2.4-fold increment in the concentration of soluble sugars, with glucose being increased by 6.0-fold. Higher levels of 1.7-, 1.8- and 1.9-fold of O-heterocyclic volatile compounds were found in the treated PK after roasting at 180 °C for 8, 14 and 20 min respectively relative to the corresponding control, with furfural, 5-methyl-2-furancarboxaldehyde, 2-furanmethanol and maltol in particularly higher amounts. Volatile differences between PKOs from control and treated PK were also found, though less obvious owing to the aqueous extraction process. Principal component analysis based on aroma-active compounds revealed that upon the proceeding of roasting, the differentiation between control and treated PK was enlarged while that of corresponding PKOs was less clear-cut. Celluclast pretreatment enabled the medium roasted PK to impart more nutty, roasty and caramelic odor and the corresponding PKO to impart more caramelic but less roasty and burnt notes. Celluclast pretreatment of PK followed by roasting may be a promising new way of improving PKO aroma. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

TOXIC ACTIVITY AND DELAYED EFFECTS OF FIVE BOTANICAL OILS ON THE FOLLOWING GENERATIONS OF AGROTIS IPSILON (HUFNAGEL) (INSECTA: LEPIDOPTERA: NOCTUIDAE) AFTER PARENTS TREATMENT.

PubMed

Mesbah, H A; El-Sayed, N A; El-Kady, M B; Mourad, A K; Kordy, A M; Henaidy, Z M

2014-01-01

The present study is carried out to evaluate the toxic efficiency and delayed effects of five botanical oils on the greasy cut worm Agrotis ipsilon (Lepidoptera: Noctuidae), as a trial for the attainment of a possible use of an alternative safe and effective phytochemicals against the insect-pest. So as to minimize or prevent the repeated usage of conventional insecticides, then reduce the environmental pollution as well as the occurring hazards to man and domestic animal due to the use of the pesticides alone. Four tested concentrations (0.5, 1.0, 1.5 and 2.5% v/v) from each of camphor, red basil, menthol, rose and anise oils, were bioassayed by treating the offered castor oil bean leaves, to the 4th instar larvae along 48h, under the laboratory higrothermic conditions of 25±2 °C and 65±5% R.H. The obtained results showed that the five tested oils were found to have more or less toxic activity and drastic effects on the inspected parameters of fitness components of the treated parent generation of the insect, in particular, pupae, emerged adult moths and laid eggs/female. In this respect camphor and red basil oils were highly effective, followed by menthol oil, anise oil and the least effective one was rose oil. Moreover, the assessed unprofitable delayed effects on the going on of the biological performance within the treated insects showed the adverse effects on the fitness components of the consequent generations (fs) post (p) one treatment with each of the bioassyed oils. The prevalence of adverse effects and disturbance in the going on biological performance through the period of (p) generation; which is followed by the distinct failure of insect development in (f1) generation were recorded for each of the tested menthol oil at 0.5 and 1.5% (v/v); camphor oil at 1.5 and 2.5% and red basil oil at 2.5% (v/v). While anise and rose oils were somewhat less efficient causing the distinct failure of the following generations up to the 3rd and/or the 6th ones. That observed distinct failure of the insect development could be attributed to the rapid or/and slow cumulative effect of the induced recessive lethal genes in both influenced sexes along the interval of the following developed generations (fs) after (p) one treatment, causing apparent adverse disturbance of the normal biological performance, which finally appears at the beginning of the failed generation.

The influence of machining condition and cutting tool wear on surface roughness of AISI 4340 steel

NASA Astrophysics Data System (ADS)

Natasha, A. R.; Ghani, J. A.; Che Haron, C. H.; Syarif, J.

2018-01-01

Sustainable machining by using cryogenic coolant as the cutting fluid has been proven to enhance some machining outputs. The main objective of the current work was to investigate the influence of machining conditions; dry and cryogenic, as well as the cutting tool wear on the machined surface roughness of AISI 4340 steel. The experimental tests were performed using chemical vapor deposition (CVD) coated carbide inserts. The value of machined surface roughness were measured at 3 cutting intervals; beginning, middle, and end of the cutting based on the readings of the tool flank wear. The results revealed that cryogenic turning had the greatest influence on surface roughness when machined at lower cutting speed and higher feed rate. Meanwhile, the cutting tool wear was also found to influence the surface roughness, either improving it or deteriorating it, based on the severity and the mechanism of the flank wear.

Strength of inserts in titanium alloy machining

NASA Astrophysics Data System (ADS)

Kozlov, V.; Huang, Z.; Zhang, J.

2016-04-01

In this paper, a stressed state of a non-worn cutting wedge in a machined titanium alloy (Ti6Al2Mo2Cr) is analyzed. The distribution of contact loads on the face of a cutting tool was obtained experimentally with the use of a ‘split cutting tool’. Calculation of internal stresses in the indexable insert made from cemented carbide (WC8Co) was carried out with the help of ANSYS 14.0 software. Investigations showed that a small thickness of the cutting insert leads to extremely high compressive stresses near the cutting edge, stresses that exceed the ultimate compressive strength of cemented carbide. The face and the base of the insert experience high tensile stresses, which approach the ultimate tensile strength of cemented carbide and increase a probability of cutting insert destruction. If the thickness of the cutting insert is bigger than 5 mm, compressive stresses near the cutting edge decrease, and tensile stresses on the face and base decrease to zero. The dependences of the greatest normal and tangential stresses on thickness of the cutting insert were found. Abbreviation and symbols: m/s - meter per second (cutting speed v); mm/r - millimeter per revolution (feed rate f); MPa - mega Pascal (dimension of specific contact loads and stresses); γ - rake angle of the cutting tool [°] α - clearance angle of the sharp cutting tool [°].

Inventories, oil shocks, and aggregate economic behavior

NASA Astrophysics Data System (ADS)

Herrera, Ana Maria

This dissertation examines the relationship between oil price shocks and aggregate economic behavior in the U.S. The first chapter addresses the effects of changes in the price of crude oil on the manufacturing sector in VAR regressions and in a structural linear quadratic inventory model. It finds that oil price increases lead to reductions in manufacturing activity while oil price falls are not followed by booms. This asymmetry in the response of the manufacturing activity, the changes in the composition of the demand, and the large variations in sales of key investment and consumption goods favor a multi-channel transmission mechanism. The analysis shows that differences in the response of the various industrial sectors are determined by the cost structure of the industry as well as by the dynamics of the demand, cost and oil shocks. Positive oil price shocks are first transmitted from the transportation equipment industry to sectors such as primary metals products, rubber and plastics and textiles, later affecting the remaining sectors and the aggregates. In the short run inventories act as a buffer however, one and a half years after the shock significant production cuts do take place. Sluggishness in the response of aggregate output can be accounted by the behavior of inventories as well as by the time lags implied in the propagation from one industry to the remaining sectors and the aggregate. The second chapter studies the role of oil prices and monetary policy in accounting for business cycles in an identified VAR framework. It finds that the slowdown in GDP growth that follows an oil shock can not be solely explained by the response of the Fed's monetary policy. An "exogenous" monetary policy that holds the fed funds rate fixed would exert a large expansionary effect. Nevertheless, conditional on this policy, the reduction in economic activity persists and the price level increases leading to a sharp reduction in the short-term interest rate. In addition, the analysis shows that this policy is unlikely from the perspective of the private agents, given the historical behavior of the U.S. monetary policy.

Agglutination of intravenously administered phosphatidylcholine-containing lipid emulsions with serum C-reactive protein.

PubMed

Tugirimana, Pierrot; Speeckaert, Marijn M; Fiers, Tom; De Buyzere, Marc L; Kint, Jos; Benoit, Dominique; Delanghe, Joris R

2013-04-01

C-reactive protein (CRP) is able to bind phospholipids in the presence of calcium. We wanted to investigate the reaction of CRP with various commercial fat emulsions and to explore the impact of CRP agglutination on serum CRP levels. Serum specimens were mixed with Intralipid 20% (soybean oil-based fat emulsion), Structolipid (structured oil-based fat emulsion), Omegaven (fish oil-based fat emulsion), or SMOFlipid (mixed soybean oil-, olive oil-, and fish oil-based emulsion) in Tris-calcium buffer (pH 7.5). After 30 minutes of incubation at 37°C, CRP-phospholipid complexes were turbidimetrically quantified and flow cytometric analysis was performed. Similarly, CRP complexes were monitored in vivo, following administration of fat emulsion. CRP was able to agglutinate phospholipid-containing lipid droplets present in the soybean oil-based fat emulsion and the structured oil-based fat emulsion. To a lesser extent, agglutination was observed for fish oil-containing fat emulsions, whereas no agglutination was noticed for the mixed soybean oil-, olive oil-, and fish oil-based emulsion. Results for propofol-containing emulsions were comparable. Agglutination correlated with phospholipid content of the emulsions. When in vivo agglutination occurred, plasma CRP values dropped due to consumption of CRP by phospholipid-induced agglutination. In this in vitro experiment, we demonstrated agglutination of CRP with phospholipids in various fat emulsions. Research studies are required in patients to determine which effects occur with various intravenous fat emulsions.

Investigation into the Effects of Textural Properties on Cuttability Performance of a Chisel Tool

NASA Astrophysics Data System (ADS)

Tumac, Deniz; Copur, Hanifi; Balci, Cemal; Er, Selman; Avunduk, Emre

2018-04-01

The main objective of this study is to investigate the effect of textural properties of stones on cutting performance of a standard chisel tool. Therewithal, the relationships between textural properties and cutting performance parameters and physical and mechanical properties were statistically analyzed. For this purpose, physical and mechanical property tests and mineralogical and petrographic analyses were carried out on eighteen natural stone samples, which can be grouped into three fundamentally different geological origins, i.e., metamorphic, igneous, and sedimentary. Then, texture coefficient analyses were performed on the samples. To determine the cuttability of the stones; the samples were cut with a portable linear cutting machine using a standard chisel tool at different depths of cut in unrelieved (non-interactive) cutting mode. The average and maximum forces (normal and cutting) and specific energy were measured, and the obtained values were correlated with texture coefficient, packing weighting, and grain size. With reference to the relation between depth of cut and cutting performance of the chisel tool for three types of natural stone groups, specific energy decreases with increasing depth of cut, and cutting forces increase in proportion to the depth of cut. The same is observed for the relationship between packing weighting and both of specific energy and cutter forces. On the other hand, specific energy and the forces decrease while grain size increases. Based on the findings of the present study, texture coefficient has strong correlation with specific energy. Generally, the lower depth of cut values in cutting tests shows higher and more reliable correlations with texture coefficient than the increased depth of cut. The results of cutting tests show also that, at a lower depth of cut (less than 1.5 mm), even stronger correlations can be observed between texture coefficient and cutting performance. Experimental studies indicate that cutting performance of chisel tools can be predicted based on texture coefficients of the natural stones.

40 CFR Appendix E to Part 112 - Determination and Evaluation of Required Response Resources for Facility Response Plans

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 1.2.3Non-persistent oils or Group 1 oils include: (1) A petroleum-based oil that, at the time of...-based oil that does not meet the distillation criteria for a non-persistent oil. Persistent oils are... appropriate group(s) for the types of oil handled, stored, or transported at the facility [persistent (Groups...

40 CFR Appendix E to Part 112 - Determination and Evaluation of Required Response Resources for Facility Response Plans

Code of Federal Regulations, 2011 CFR

2011-07-01

.... 1.2.3Non-persistent oils or Group 1 oils include: (1) A petroleum-based oil that, at the time of...-based oil that does not meet the distillation criteria for a non-persistent oil. Persistent oils are... appropriate group(s) for the types of oil handled, stored, or transported at the facility [persistent (Groups...

26 CFR 1.954-8 - Foreign base company oil related income.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 10 2012-04-01 2012-04-01 false Foreign base company oil related income. 1.954...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Controlled Foreign Corporations § 1.954-8 Foreign base company oil related income. (a) Foreign base company oil related income—(1) In general. Under section 954...

40 CFR 446.10 - Applicability; description of the oil-base solvent wash paint subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS PAINT FORMULATING POINT SOURCE CATEGORY Oil-Base Solvent Wash Paint Subcategory § 446.10 Applicability; description of the oil-base solvent wash... production of oil-base paint where the tank cleaning is performed using solvents. When a plant is subject to...

Synthesis of chloro alkoxy and alkoxy derivatives of methyl oleate

USDA-ARS?s Scientific Manuscript database

Vegetable oil based lubricants typically have improved lubricity and biodegradability over their mineral oil based counterparts. However, vegetable oil lubricants often fail to meet the performance standards of mineral based oils with respect to cold temperature and resistance to oxidation. Olefins ...

Stability analysis of multipoint tool equipped with metal cutting ceramics

NASA Astrophysics Data System (ADS)

Maksarov, V. V.; Khalimonenko, A. D.; Matrenichev, K. G.

2017-10-01

The article highlights the issues of determining the stability of the cutting process by a multipoint cutting tool equipped with cutting ceramics. There were some recommendations offered on the choice of parameters of replaceable cutting ceramic plates for milling based of the conducted researches. Ceramic plates for milling are proposed to be selected on the basis of value of their electrical volume resistivity.

CO 2 laser cutting of MDF . 2. Estimation of power distribution

NASA Astrophysics Data System (ADS)

Ng, S. L.; Lum, K. C. P.; Black, I.

2000-02-01

Part 2 of this paper details an experimentally-based method to evaluate the power distribution for both CW and PM cutting. Variations in power distribution with different cutting speeds, material thickness and pulse ratios are presented. The paper also provides information on both the cutting efficiency and absorptivity index for MDF, and comments on the beam dispersion characteristics after the cutting process.

[A graph cuts-based interactive method for segmentation of magnetic resonance images of meningioma].

PubMed

Li, Shuan-qiang; Feng, Qian-jin; Chen, Wu-fan; Lin, Ya-zhong

2011-06-01

For accurate segmentation of the magnetic resonance (MR) images of meningioma, we propose a novel interactive segmentation method based on graph cuts. The high dimensional image features was extracted, and for each pixel, the probabilities of its origin, either the tumor or the background regions, were estimated by exploiting the weighted K-nearest neighborhood classifier. Based on these probabilities, a new energy function was proposed. Finally, a graph cut optimal framework was used for the solution of the energy function. The proposed method was evaluated by application in the segmentation of MR images of meningioma, and the results showed that the method significantly improved the segmentation accuracy compared with the gray level information-based graph cut method.

Optimization of self-aligned double patterning (SADP)-compliant layout designs using pattern matching for sub-20nm metal routing

NASA Astrophysics Data System (ADS)

Wang, Lynn T.-N.; Schroeder, Uwe Paul; Madhavan, Sriram

2017-03-01

A pattern-based methodology for optimizing SADP-compliant layout designs is developed based on identifying cut mask patterns and replacing them with pre-characterized fixing solutions. A pattern-based library of difficult-tomanufacture cut patterns with pre-characterized fixing solutions is built. A pattern-based engine searches for matching patterns in the decomposed layouts. When a match is found, the engine opportunistically replaces the detected pattern with a pre-characterized fixing solution. The methodology was demonstrated on a 7nm routed metal2 block. A small library of 30 cut patterns increased the number of more manufacturable cuts by 38% and metal-via enclosure by 13% with a small parasitic capacitance impact of 0.3%.

The supramolecular chemistry of lipid oxidation and antioxidation in bulk oils

PubMed Central

Budilarto, Elizabeth S; Kamal-Eldin, Afaf

2015-01-01

The microenvironment formed by surface active compounds is being recognized as the active site of lipid oxidation. Trace amounts of water occupy the core of micro micelles and several amphiphilic minor components (e.g., phospholipids, monoacylglycerols, free fatty acids, etc.) act as surfactants and affect lipid oxidation in a complex fashion dependent on the structure and stability of the microemulsions in a continuous lipid phase such as bulk oil. The structures of the triacylglycerols and other lipid-soluble molecules affect their organization and play important roles during the course of the oxidation reactions. Antioxidant head groups, variably located near the water-oil colloidal interfaces, trap and scavenge radicals according to their location and concentration. According to this scenario, antioxidants inhibit lipid oxidation not only by scavenging radicals via hydrogen donation but also by physically stabilizing the micelles at the microenvironments of the reaction sites. There is a cut-off effect (optimum value) governing the inhibitory effects of antioxidants depending inter alias on their hydrophilic/lipophilic balance and their concentrations. These complex effects, previously considered as paradoxes in antioxidants research, are now better explained by the supramolecular chemistry of lipid oxidation and antioxidants, which is discussed in this review. PMID:26448722

In-vitro propagation and antimycotic potential of extracts and essential oil of roots of Aristolochia bracteolata Linn. (Aristolochiaceae).

PubMed

Gbadamosi, I T; Egunyomi, A

2012-01-01

In spite of the therapeutic importance of Aristolochia bracteolata Linn. in Nigerian ethnomedicine, it is largely collected from the wild. Owing to the acclaimed potency of the plant and the difficulty in treating candidiasis, the anticandidal activity and in vitro propagation of the plant were investigated. Phytochemical screening and preparation of extracts of the roots were done using standard procedures. Clinical isolates of Candida albicans were screened against extracts and essential oil of Aristolochia bracteolata root using agar-well diffusion method. Minimum Inhibitory Concentration (MIC) of the ethanol extract was determined using broth dilution method. The nodal cuttings of A. bracteolata were cultured on Murashige and Skoog (MS) basal media. A. bracteolata contained alkaloids, saponins and cardenolides. The water extract was inactive on all isolates. The ethanol extract (500 mg/ml) and essential oil (undiluted) exhibited anticandidal activity on 9 out of 10 isolates at 10(1) - 10(6) cfu/ml inoculums concentration. Green growth and callus formation were observed in explants cultured on MS basal media after 30 days. A. bracteolata could be a source of anticandidal phytomedicine and the in vitro propagation confirmed its sustainability as anticandidal agent.

The BP oil spill and the bounty of Plaquemines Parish.

PubMed

Fertel, Randy

2011-01-01

The source of 25 to 30 percent of America's seafood, the Mississippi River Delta's cornucopian world is now uncertain. And yet, even if shrimp, oysters, and finfish are unaffected by the BP Oil Spill - a big if - one can already reflect on the passing of the culture once built upon gathering them. For almost three centuries, levees made life possible along the riverbanks and in the wetlands beyond. Those same levees also ensured the wetlands would eventually melt away into the Gulf. Cutting off the silt left behind during annual river inundations subjected the fragile land to erosion. Sulfur, natural gas, and oil production companies dug twenty thousand miles of canals to gain more direct routes to their fields and to pump out their mineral wealth. This caused salt-water intrusion that killed off plant life and caused more erosion. The world that sustained my Plaquemines ancestors was less subject to collapse following disasters not only because the ecosystem before the wetlands' ongoing loss was then more vibrant, complex, and robust; but also because their lives, especially their culinary lives, were more vibrant, complex, and robust. Life was hard, but when it came to putting food on the table, life followed the seasons.

Environmental projects. Volume 13: Underground storage tanks, removal and replacement. Goldstone Deep Space Communications Complex

NASA Technical Reports Server (NTRS)

Bengelsdorf, Irv

1991-01-01

The Goldstone Deep Space Communications Complex (GDSCC), located in the Mojave Desert about 40 miles north of Barstow, California, and about 160 miles northeast of Pasadena, is part of the National Aeronautics and Space Administration's (NASA's) Deep Space Network, one of the world's largest and most sensitive scientific telecommunications and radio navigation networks. Activities at the GDSCC are carried out in support of six large parabolic dish antennas. As a large-scale facility located in a remote, isolated desert region, the GDSCC operations require numerous on-site storage facilities for gasoline, diesel oil, hydraulic oil, and waste oil. These fluids are stored in underground storage tanks (USTs). This present volume describes what happened to the 26 USTs that remained at the GDSCC. Twenty-four of these USTs were constructed of carbon steel without any coating for corrosion protection, and without secondary containment or leak detection. Two remaining USTs were constructed of fiberglass-coated carbon steel but without secondary containment or leak protection. Of the 26 USTs that remained at the GDSCC, 23 were cleaned, removed from the ground, cut up, and hauled away from the GDSCC for environmentally acceptable disposal. Three USTs were permanently closed (abandoned in place).

Research Support and Publications Activity for the Edward L. Ginzton Laboratory

DTIC Science & Technology

1978-10-01

wave’. along thle I1I0 crystal di iect ion satisfy,, anld it cain be alccomlihled witIl h ielt a cy. oil /-cut su1rfaces. Tedelay I iile conlst Iuct ion...to Theory and Application, Academic Press, New York, 1967. S-58-_ _ _ __ _ _ __ _ _I 724 rROCE DINGS OF T1lE IEEE, MAY 1976 Acoustoelectric... Academic p’ress, 1967. Iiiterscience. 1969. 14)N. .1. M~oll, 0. W. Otto, aiid C. F. Quate. "Scanning optical pst- 1561 E. If. Nicolliati anid A. Goetiberger

Brunei-Sarawak Border

NASA Image and Video Library

2017-10-31

The southwestern border of Brunei with Sarawak, Malaysia is strikingly apparent due to differences in land use practice. On the Malaysian side, a spider web of small roads indicates intensive land use: in this case clearing of the forest for palm oil plantations. On the Brunei side, the virgin forest is preserved, with few if any roads cutting through the forest. The image was acquired September 10, 2012, covers an area of 38 by 38 km, and is located at 4.2 degrees north, 114.4 degrees east. https://photojournal.jpl.nasa.gov/catalog/PIA22034

Multiphase fluid characterization system

DOEpatents

Sinha, Dipen N.

2014-09-02

A measurement system and method for permitting multiple independent measurements of several physical parameters of multiphase fluids flowing through pipes are described. Multiple acoustic transducers are placed in acoustic communication with or attached to the outside surface of a section of existing spool (metal pipe), typically less than 3 feet in length, for noninvasive measurements. Sound speed, sound attenuation, fluid density, fluid flow, container wall resonance characteristics, and Doppler measurements for gas volume fraction may be measured simultaneously by the system. Temperature measurements are made using a temperature sensor for oil-cut correction.

Cutting the Army’s Umbilical Cord: A Study of Emerging Fuel Technologies and Their Impact on National Security

DTIC Science & Technology

2011-12-01

fuel saving technologies that may be on the civilian market but have not been vetted through the Army procurement process. Some are also military...global market . 18 This heavy dependence also requires that the U.S. use military forces to ensure access to oil both for the health of the U.S...the market price. However, what the cost per gallon does not include is the transparent costs that the FBCF captures. Using the AEPI Reports’ value of

Effects of roads and well pads on erosion in the Largo Canyon watershed, New Mexico, 2001-02

USGS Publications Warehouse

Matherne, Anne Marie

2006-01-01

Largo Canyon, located in the San Juan Basin of northwestern New Mexico, is one of the longest dry washes in the world. Oil and gas production in the San Juan Basin, which began in the 1940's, required the development of an extensive network of dirt roads to service the oil and gas wells in the Navajo Reservoir area. Presently, there are about eight wells per square mile, and the density of oil and gas wells is expected to increase. Potential environmental effects on landscape stability that may result from the additional roads and well pads have not been documented. In 2001, the U.S. Geological Survey began a study in cooperation with the Bureau of Land Management to evaluate the effects of roads and well pads associated with oil and gas operations on the erosion potential of Bureau of Land Management lands in the Largo Canyon watershed. The effects of roads and well pads on erosion were quantified by installing sediment dams (dams) and by surveying transects across roads and well pads. Data from 26 dams were used in the analysis. Dams were installed at 43 sites: 21 on hillsides upslope from roads or pads to measure erosion from hillslopes, 11 at the downslope edges of roads to measure erosion from roads, and 11 at the downslope edges of well pads to measure erosion from well pads. Pairs of survey transects were established at nine well pads and two road locations. Sediment-accumulation data for 26 dams, recorded at 17 measurement intervals, indicate that average erosion rates at the dams significantly correlate to size of the contributing area. The average erosion rate normalized by drainage area was 0.001 foot per year below roads, 0.003 foot per year on hillslopes, and 0.011 foot per year below well pads. Results of a two-sample t-test indicate that there was no significant difference in average erosion rates for dams located on hillslopes and below roads, whereas average erosion rates were significantly greater for dams below well pads than for dams on hillslopes and dams below roads. The average erosion rates estimated from the data collected during this study most likely represent minimum erosion rates. Sediment-accumulation data for measurement intervals and for dams that were breached during 2002, resulting from the large volume of runoff generated by high-intensity storms, were not used to compute erosion rates. For this reason, the higher range of erosion rates is underrepresented and the results of this study are biased toward the lower end of the range of erosion rates. Measurements along road transects generally indicate that sediment is eroded from the top of road berms and redeposited at the base of the berms and may be transported downslope along the road. Measurements along well-pad transects generally indicate that sediment eroded from hillslopes is transported over the surface of the well pad and down the well-pad edges. Based on field observations, roads aligned parallel to topographic contours facilitate erosional processes in two ways: (1) roads cut across and collect runoff from previously established drainages and (2) roads, where they are cut into hillsides or into the land surface, provide focal points for the initiation of erosion. Roads aligned across topographic contours can serve as conduits to channel runoff but do not constitute a large percentage of the road network.

A Major Unconformity Between Permian and Triassic Strata at Cape Kekurnoi, Alaska Peninsula: Old and New Observations on Stratigraphy and Hydrocarbon Potential

USGS Publications Warehouse

Blodgett, Robert B.; Sralla, Bryan

2008-01-01

A major angular unconformity separates carbonates and shales of the Upper Triassic Kamishak Formation from an underlying unnamed sequence of Permian agglomerate, volcaniclastic rocks (sandstone), and limestone near Puale Bay on the Alaska Peninsula. For the first time, we photographically document the angular unconformity in outcrop, as clearly exposed in a seacliff ~1.3 mi (2.1 km) west of Cape Kekurnoi in the Karluk C?4 and C?5 1:63,360-scale quadrangles. This unconformity is also documented by examination of core chips, ditch cuttings, and (or) open-hole electrical logs in two deep oil-and-gas-exploration wells (Humble Oil & Refining Co.?s Bear Creek No. 1 and Standard Oil Co. of California?s Grammer No. 1) drilled along the Alaska Peninsula southwest of Puale Bay. A third well (Richfield Oil Corp.?s Wide Bay Unit No. 1), south of and structurally on trend with the other two wells, probed deeply into the Paleozoic basement, but Triassic strata are absent, owing to either a major unconformity or a large fault. Here we briefly review current and newly acquired data on Permian and Triassic rocks of the Puale Bay-Becharof Lake-Wide Bay area on the basis of an examination of surface and subsurface materials. The resulting reinterpretation of the Permian and Triassic stratigraphy has important economic ramifications for oil and gas exploration on the Alaska Peninsula and in the Cook Inlet basin. We also present a history of petroleum exploration targeting Upper Triassic reservoirs in the region.

The Future of Fossil Fuels: A Century of Abundance or a Century of Decline?

NASA Astrophysics Data System (ADS)

Nelder, C.

2012-12-01

Horizontal drilling, hydraulic fracturing, and other advanced technologies have spawned a host of new euphoric forecasts of hydrocarbon abundance. Yet although the world's remaining oil and gas resources are enormous, most of them are destined to stay in the ground due to real-world constraints on price, flow rates, investor appetite, supply chain security, resource quality, and global economic conditions. While laboring under the mistaken belief that it sits atop a 100-year supply of natural gas, the U.S. is contemplating exporting nearly all of its shale gas production even as that production is already flattening due to poor economics. Instead of bringing "energy independence" to the U.S. and making it the top oil exporter, unrestricted drilling for tight oil and in the federal outer continental shelf would cut the lifespan of U.S. oil production in half and make it the world's most desperate oil importer by mid-century. And current forecasts for Canadian tar sands production are as unrealistic as their failed predecessors. Over the past century, world energy production has moved progressively from high quality resources with high production rates and low costs to lower quality resources with lower production rates and higher costs, and that progression is accelerating. Soon we will discover the limits of practical extraction, as production costs exceed consumer price tolerance. Oil and gas from tight formations, shale, bitumen, kerogen, coalbeds, deepwater, and the Arctic are not the stuff of new abundance, but the oil junkie's last dirty fix. This session will highlight the gap between the story the industry tells about our energy future, and the story the data tells about resource size, production rates, costs, and consumer price tolerance. It will show why it's time to put aside unrealistic visions of continued dependence on fossil fuels, face up to a century of decline, and commit ourselves to energy and transportation transition.

Geometry and material choices govern hard-rock drilling performance of PDC drag cutters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wise, Jack LeRoy

2005-06-01

Sandia National Laboratories has partnered with industry on a multifaceted, baseline experimental study that supports the development of improved drag cutters for advanced drill bits. Different nonstandard cutter lots were produced and subjected to laboratory tests that evaluated the influence of selected design and processing parameters on cutter loads, wear, and durability pertinent to the penetration of hard rock with mechanical properties representative of formations encountered in geothermal or deep oil/gas drilling environments. The focus was on cutters incorporating ultrahard PDC (polycrystalline diamond compact) overlays (i.e., diamond tables) on tungsten-carbide substrates. Parameter variations included changes in cutter geometry, material composition,more » and processing conditions. Geometric variables were the diamond-table thickness, the cutting-edge profile, and the PDC/substrate interface configuration. Material and processing variables for the diamond table were, respectively, the diamond particle size and the sintering pressure applied during cutter fabrication. Complementary drop-impact, granite-log abrasion, linear cutting-force, and rotary-drilling tests examined the response of cutters from each lot. Substantial changes in behavior were observed from lot to lot, allowing the identification of features contributing major (factor of 10+) improvements in cutting performance for hard-rock applications. Recent field demonstrations highlight the advantages of employing enhanced cutter technology during challenging drilling operations.« less

Optimization of turning process through the analytic flank wear modelling

NASA Astrophysics Data System (ADS)

Del Prete, A.; Franchi, R.; De Lorenzis, D.

2018-05-01

In the present work, the approach used for the optimization of the process capabilities for Oil&Gas components machining will be described. These components are machined by turning of stainless steel castings workpieces. For this purpose, a proper Design Of Experiments (DOE) plan has been designed and executed: as output of the experimentation, data about tool wear have been collected. The DOE has been designed starting from the cutting speed and feed values recommended by the tools manufacturer; the depth of cut parameter has been maintained as a constant. Wear data has been obtained by means the observation of the tool flank wear under an optical microscope: the data acquisition has been carried out at regular intervals of working times. Through a statistical data and regression analysis, analytical models of the flank wear and the tool life have been obtained. The optimization approach used is a multi-objective optimization, which minimizes the production time and the number of cutting tools used, under the constraint on a defined flank wear level. The technique used to solve the optimization problem is a Multi Objective Particle Swarm Optimization (MOPS). The optimization results, validated by the execution of a further experimental campaign, highlighted the reliability of the work and confirmed the usability of the optimized process parameters and the potential benefit for the company.

Material properties and laser cutting of composites

NASA Astrophysics Data System (ADS)

Chen, Chia-Chieh; Cheng, Wing

Laser (Light Amplification by Stimulated Emission of Radiation) has been used successfully for many material cutting, drilling, metal welding and heat treating applications. However, laser cutting of polymer composites were attempted with varying degrees of success. Because composites are heterogeneous, the energy applied by laser could result in severe resin degradation before fibers were cut. In this study, cutting of glass, Kevlar, and graphite composites were evaluated based on their material properties and laser cutting parameters. A transient heat transfer analysis was used to determine the relative heat affected zones of these composites. Kevlar composites can be cut very well while graphite composites are difficult to cut. Though the cutting process is much more complicated in reality, the analysis provides a semi-quantitative perspective on the characteristics and limitations of laser cutting of different composites.

Spectrally selective solar absorber with sharp and temperature dependent cut-off based on semiconductor nanowire arrays

NASA Astrophysics Data System (ADS)

Wang, Yang; Zhou, Lin; Zheng, Qinghui; Lu, Hong; Gan, Qiaoqiang; Yu, Zongfu; Zhu, Jia

2017-05-01

Spectrally selective absorbers (SSA) with high selectivity of absorption and sharp cut-off between high absorptivity and low emissivity are critical for efficient solar energy conversion. Here, we report the semiconductor nanowire enabled SSA with not only high absorption selectivity but also temperature dependent sharp absorption cut-off. By taking advantage of the temperature dependent bandgap of semiconductors, we systematically demonstrate that the absorption cut-off profile of the semiconductor-nanowire-based SSA can be flexibly tuned, which is quite different from most of the other SSA reported so far. As an example, silicon nanowire based selective absorbers are fabricated, with the measured absorption efficiency above (below) bandgap ˜97% (15%) combined with an extremely sharp absorption cut-off (transition region ˜200 nm), the sharpest SSA demonstrated so far. The demonstrated semiconductor-nanowire-based SSA can enable a high solar thermal efficiency of ≳86% under a wide range of operating conditions, which would be competitive candidates for the concentrated solar energy utilizations.

Development of karanja oil based offset printing ink in comparison with linseed oil.

PubMed

Bhattacharjee, Moumita; Roy, Ananda Sankar; Ghosh, Santinath; Dey, Munmun

2011-01-01

The conventional offset lithographic printing ink is mainly based on linseed oil. But in recent years, due to stiff competition from synthetic substitutes mainly from petroleum products, the crop production shrinks down to an unsustainable level, which increases the price of linseed oil. Though soyabean oil has replaced a major portion of linseed oil, it is also necessary to develop alternate cost effective vegetable oils for printing ink industry. The present study aims to evaluate the performance of karanja oil (Pongamia glabra) as an alternative of linseed oil in the formulation of offset printing ink because karanja oil is easily available in rural India. Physical properties of raw karanja oil are measured and compared with that of alkali refined linseed oil. Rosin modified phenolic resin based varnishes were made with linseed oil as well as with karanja oil and their properties are compared. Sheetfed offset inks of process colour yellow and cyan is chosen to evaluate the effect of karanja oil in ink properties. In conclusion, karanja oil can be accepted as an alternate vegetable oil source with its noticeable effect on print and post print properties with slower drying time on paper. However, the colour and odour of the oil will restrict its usage on offset inks.

Computer optimization of cutting yield from multiple ripped boards

Treesearch

A.R. Stern; K.A. McDonald

1978-01-01

RIPYLD is a computer program that optimizes the cutting yield from multiple-ripped boards. Decisions are based on automatically collected defect information, cutting bill requirements, and sawing variables. The yield of clear cuttings from a board is calculated for every possible permutation of specified rip widths and both the maximum and minimum percent yield...

Design and Test Research on Cutting Blade of Corn Harvester Based on Bionic Principle.

PubMed

Tian, Kunpeng; Li, Xianwang; Zhang, Bin; Chen, Qiaomin; Shen, Cheng; Huang, Jicheng

2017-01-01

Existing corn harvester cutting blades have problems associated with large cutting resistance, high energy consumption, and poor cut quality. Using bionics principles, a bionic blade was designed by extracting the cutting tooth profile curve of the B. horsfieldi palate. Using a double-blade cutting device testing system, a single stalk cutting performance contrast test for corn stalks obtained at harvest time was carried out. Results show that bionic blades have superior performance, demonstrated by strong cutting ability and good cut quality. Using statistical analysis of two groups of cutting test data, the average cutting force and cutting energy of bionic blades and ordinary blades were obtained as 480.24 N and 551.31 N and 3.91 J and 4.38 J, respectively. Average maximum cutting force and cutting energy consumption for the bionic blade were reduced by 12.89% and 10.73%, respectively. Variance analysis showed that both blade types had a significant effect on maximum cutting energy and cutting energy required to cut a corn stalk. This demonstrates that bionic blades have better cutting force and energy consumption reduction performance than ordinary blades.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferrell, Jack R; Ware, Anne E

Two catalytic fast pyrolysis (CFP) oils (bottom/heavy fraction) were analyzed in various solvents that are used in common analytical methods (nuclear magnetic resonance - NMR, gas chromatography - GC, gel permeation chromatography - GPC, thermogravimetric analysis - TGA) for oil characterization and speciation. A more accurate analysis of the CFP oils can be obtained by identification and exploitation of solvent miscibility characteristics. Acetone and tetrahydrofuran can be used to completely solubilize CFP oils for analysis by GC and tetrahydrofuran can be used for traditional organic GPC analysis of the oils. DMSO-d6 can be used to solubilize CFP oils for analysismore » by 13C NMR. The fractionation of oils into solvents that did not completely solubilize the whole oils showed that miscibility can be related to the oil properties. This allows for solvent selection based on physico-chemical properties of the oils. However, based on semi-quantitative comparisons of the GC chromatograms, the organic solvent fractionation schemes did not speciate the oils based on specific analyte type. On the other hand, chlorinated solvents did fractionate the oils based on analyte size to a certain degree. Unfortunately, like raw pyrolysis oil, the matrix of the CFP oils is complicated and is not amenable to simple liquid-liquid extraction (LLE) or solvent fractionation to separate the oils based on the chemical and/or physical properties of individual components. For reliable analyses, for each analytical method used, it is critical that the bio-oil sample is both completely soluble and also not likely to react with the chosen solvent. The adoption of the standardized solvent selection protocols presented here will allow for greater reproducibility of analysis across different users and facilities.« less

HFRR investigation of biobased and petroleum based oils

USDA-ARS?s Scientific Manuscript database

Biobased oils come in a wide range of chemical structures as do petroleum based oils. In addition, a distinct structural difference exists between these two broad categories of oils. Previous work has shown that, in spite of the structural differences, these two categories of oils display similar pr...

Research on NC laser combined cutting optimization model of sheet metal parts

NASA Astrophysics Data System (ADS)

Wu, Z. Y.; Zhang, Y. L.; Li, L.; Wu, L. H.; Liu, N. B.

2017-09-01

The optimization problem for NC laser combined cutting of sheet metal parts was taken as the research object in this paper. The problem included two contents: combined packing optimization and combined cutting path optimization. In the problem of combined packing optimization, the method of “genetic algorithm + gravity center NFP + geometric transformation” was used to optimize the packing of sheet metal parts. In the problem of combined cutting path optimization, the mathematical model of cutting path optimization was established based on the parts cutting constraint rules of internal contour priority and cross cutting. The model played an important role in the optimization calculation of NC laser combined cutting.

Impact of exploratory wells, offshore Florida: A biological assessment

USGS Publications Warehouse

Dustan, Phillip A.; Lidz, Barbara H.; Shinn, Eugene A.

1991-01-01

Seven offshore exploratory oil well sites were examined in an effort to determine the ecological impact of exploratory drilling on the subtropical marine ecosystems of southern Florida, including seagrass beds and coral reefs. The time since drilling ranged from 2 to 29 years; water depths varied between 5 and 70 m. The major long-term ecological impact observed at these sites ranged from the creation of "artificial-reef" conditions to the physical destruction of hardbottom habitat that had not recovered in 29 years. Long-term ecological perturbation appeared to be limited to physical destruction and the deposition of drilling debris, which provided substratum for settling organisms. Significant deposits of drill muds or cuttings were not encountered at any of the sites, and there was no evidence of ecological damage from cuttings or drill muds. The results of this study pertain only to exploratory drilling that, unlike production wells that remain in place for tens of years, is a one-time perturbation to the habitat.

Aspects of the tribological behaviour of powders recycled from rapid steel treated sub-zero

NASA Astrophysics Data System (ADS)

Radu, S.; Ciobanu, M.

2017-02-01

The recycling of high-alloyed steels represents a significant opportunity in Powder Metallurgy as it permits the use of raw materials with relatively low prices compared to the conventional methods. Recycling can be achieved by two methods: from spraying debris resulted from worn cutting tools and processes obtained from processing chip drilling and re-sharpening of tools. The research aims to confirm that wastes from rapid steels can become, by the successive processing, metal powders that can thereafter be used for cutting tools of lathe type removable plate. After pressing and sintering the recycling powder, cylindrical samples were obtained that were subsequently applied a subcritical annealing. Wear tests conducted on a tribometer type TRB-01-02541 confirmed that their wear resistance is superior to the same samples that were sintered, hardened and tempered in oil. This paper was accepted for publication in Proceedings after double peer reviewing process but was not presented at the Conference ROTRIB’16.

Method of extruding and packaging a thin sample of reactive material including forming the extrusion die

DOEpatents

Lewandowski, Edward F.; Peterson, Leroy L.

1985-01-01

This invention teaches a method of cutting a narrow slot in an extrusion die with an electrical discharge machine by first drilling spaced holes at the ends of where the slot will be, whereby the oil can flow through the holes and slot to flush the material eroded away as the slot is being cut. The invention further teaches a method of extruding a very thin ribbon of solid highly reactive material such as lithium or sodium through the die in an inert atmosphere of nitrogen, argon or the like as in a glovebox. The invention further teaches a method of stamping out sample discs from the ribbon and of packaging each disc by sandwiching it between two aluminum sheets and cold welding the sheets together along an annular seam beyond the outer periphery of the disc. This provides a sample of high purity reactive material that can have a long shelf life.

Method of extruding and packaging a thin sample of reactive material, including forming the extrusion die

DOEpatents

Lewandowski, E.F.; Peterson, L.L.

1981-11-30

This invention teaches a method of cutting a narrow slot in an extrusion die with an electrical discharge machine by first drilling spaced holes at the ends of where the slot will be, whereby the oil can flow through the holes and slot to flush the material eroded away as the slot is being cut. The invention further teaches a method of extruding a very thin ribbon of solid highly reactive material such as lithium or sodium through the die in an inert atmosphere of nitrogen, argon, or the like as in a glovebox. The invention further teaches a method of stamping out sample discs from the ribbon and of packaging each disc by sandwiching it between two aluminum sheets and cold welding the sheets together along an annular seam beyond the outer periphery of the disc. This provides a sample of high purity reactive material that can have a long shelf life.

Development of underwater cutting system by abrasive water-jet

NASA Astrophysics Data System (ADS)

Demura, Kenji; Yamaguchi, Hitoshi

1993-09-01

The technology to cut objects in the ocean's depths with abrasive water jets was examined for possible application in view of the greater water depths and sophistication involved in work on the ocean floor today. A test model was developed to study this technology's safety and practicability. The test model was designed for use at great water depths and has functions and a configuration that are unlike equipment used on land. A continuous, stable supply of abrasive is a distinctive design feature. In land applications, there had been problems with plugged tubes and an uneven supply. For this reason, the abrasive was converted to slurry form, and a continuous pressurized tube pump system was adopted for supply to the nozzle head. Also, a hydraulic motor that does not employ oil or electric power was used to provide an underwater drive that is environment-friendly. The report outlines the technology's general design concept including its distinctive functions and its configuration for use at great depths, and the report provides great detail on the equipment.

Nanoemulsion-based delivery systems for polyunsaturated (ω-3) oils: formation using a spontaneous emulsification method.

PubMed

Gulotta, Alessandro; Saberi, Amir Hossein; Nicoli, Maria Cristina; McClements, David Julian

2014-02-19

Nanoemulsion-based delivery systems are finding increasing utilization to encapsulate lipophilic bioactive components in food, personal care, cosmetic, and pharmaceutical applications. In this study, a spontaneous emulsification method was used to fabricate nanoemulsions from polyunsaturated (ω-3) oils, that is, fish oil. This low-energy method relies on formation of fine oil droplets when an oil/surfactant mixture is added to an aqueous solution. The influence of surfactant-to-oil ratio (SOR), oil composition (lemon oil and MCT), and cosolvent composition (glycerol, ethanol, propylene glycol, and water) on the formation and stability of the systems was determined. Optically transparent nanoemulsions could be formed by controlling SOR, oil composition, and aqueous phase composition. The spontaneous emulsification method therefore has considerable potential for fabricating nanoemulsion-based delivery systems for incorporating polyunsatured oils into clear food, personal care, and pharmaceutical products.

Oxygen speciation in upgraded fast pyrolysis bio-oils by comprehensive two-dimensional gas chromatography.

PubMed

Omais, Badaoui; Crepier, Julien; Charon, Nadège; Courtiade, Marion; Quignard, Alain; Thiébaut, Didier

2013-04-21

Biomass fast pyrolysis is considered as a promising route to produce liquid for the transportation field from a renewable resource. However, the derived bio-oils are mainly oxygenated (45-50%w/w O on a wet basis) and contain almost no hydrocarbons. Therefore, upgrading is necessary to obtain a liquid with lower oxygen content and characterization of oxygenated compounds in these products is essential to assist conversion reactions. For this purpose, comprehensive two-dimensional gas chromatography (GC × GC) can be investigated. Oxygen speciation in such matrices is hampered by the large diversity of oxygenated families and the complexity of the hydrocarbon matrix. Moreover, response factors must be taken into account for oxygenate quantification as the Flame Ionisation Detector (FID) response varies when a molecule contains heteroatoms. To conclude, no distillation cuts were accessible and the analysis had to cover a large range of boiling points (30-630 °C). To take up this analytical challenge, a thorough optimization approach was developed. In fact, four GC × GC column sets were investigated to separate oxygenated compounds from the hydrocarbon matrix. Both model mixtures and the upgraded biomass flash pyrolysis oil were injected using GC × GC-FID to reach a suitable chromatographic separation. The advantages and drawbacks of each column combination for oxygen speciation in upgraded bio-oils are highlighted in this study. Among the four sets, an original polar × semi-polar column combination was selected and enabled the identification by GC × GC-ToF/MS of more than 40 compounds belonging to eight chemical families: ketones, furans, alcohols, phenols, carboxylic acids, guaiacols, anisols, and esters. For quantification purpose, the GC × GC-FID chromatogram was divided into more than 60 blobs corresponding to the previously identified analyte and hydrocarbon zones. A database associating each blob to a molecule and its specific response factor (determined by standards injection at different concentrations) was created. A detailed molecular quantification by GC × GC-FID was therefore accessible after integration of the corrected normalized areas. This paper aims to present a detail level in terms of characterization of oxygenated compounds in upgraded bio-oils which to our knowledge has never been reached so far. It is based on an original column set selection and an extremely accurate quantification procedure.

Bio-based Hydraulic Fluids

DTIC Science & Technology

2008-04-17

DEHULL, FLAKE HEXANE EXTRACTION PRESS HEXANE DISTILLATION CRUDE OIL 0.1-3% phosphatides 1% fatty acids 1 ppm chlorophyll DEGUM (H2 O, H3 PO4...program www.bfrl.nist.gov/oae/bees.html 617 April 2008 Seed Oils and Their Fatty Acid and Genetic Varieties Source: Leissner, O. et al (1989) Vegetable...Oils and Fats, Karlshammn, Sweden 717 April 2008 Bio-based Oil Process Volatile impurities: odor (aldehydes & ketones) fatty acids Bio-based Oil CRACK

Manufacturing vegetable oil based biodiesel: An engineering management perspective

USDA-ARS?s Scientific Manuscript database

According to the USDA, 6.45 million tons of cottonseed was produced in 2007. Each ton will yield approximately 44 to 46 gallons unrefined oil. Cottonseed oil bio-diesel could have the potential to create a more competitive oil market for oil mills. The proposed cost model is based on an existing cot...

Comparative Assessment of Cutting Inserts and Optimization during Hard Turning: Taguchi-Based Grey Relational Analysis

NASA Astrophysics Data System (ADS)

Venkata Subbaiah, K.; Raju, Ch.; Suresh, Ch.

2017-08-01

The present study aims to compare the conventional cutting inserts with wiper cutting inserts during the hard turning of AISI 4340 steel at different workpiece hardness. Type of insert, hardness, cutting speed, feed, and depth of cut are taken as process parameters. Taguchi’s L18 orthogonal array was used to conduct the experimental tests. Parametric analysis carried in order to know the influence of each process parameter on the three important Surface Roughness Characteristics (Ra, Rz, and Rt) and Material Removal Rate. Taguchi based Grey Relational Analysis (GRA) used to optimize the process parameters for individual response and multi-response outputs. Additionally, the analysis of variance (ANOVA) is also applied to identify the most significant factor.

Finite pure integer programming algorithms employing only hyperspherically deduced cuts

NASA Technical Reports Server (NTRS)

Young, R. D.

1971-01-01

Three algorithms are developed that may be based exclusively on hyperspherically deduced cuts. The algorithms only apply, therefore, to problems structured so that these cuts are valid. The algorithms are shown to be finite.

Surface roughness model based on force sensors for the prediction of the tool wear.

PubMed

de Agustina, Beatriz; Rubio, Eva María; Sebastián, Miguel Ángel

2014-04-04

In this study, a methodology has been developed with the objective of evaluating the surface roughness obtained during turning processes by measuring the signals detected by a force sensor under the same cutting conditions. In this way, the surface quality achieved along the process is correlated to several parameters of the cutting forces (thrust forces, feed forces and cutting forces), so the effect that the tool wear causes on the surface roughness is evaluated. In a first step, the best cutting conditions (cutting parameters and radius of tool) for a certain quality surface requirement were found for pieces of UNS A97075. Next, with this selection a model of surface roughness based on the cutting forces was developed for different states of wear that simulate the behaviour of the tool throughout its life. The validation of this model reveals that it was effective for approximately 70% of the surface roughness values obtained.

Novel polymeric materials from vegetable oils and vinyl monomers: preparation, properties, and applications.

PubMed

Lu, Yongshang; Larock, Richard C

2009-01-01

Veggie-based products: Vegetable-oil-based polymeric materials, prepared by free radical, cationic, and olefin metathesis polymerizations, range from soft rubbers to ductile or rigid plastics, and to high-performance biocomposites and nanocomposites. They display a wide range of thermophysical and mechanical properties and may find promising applications as alternatives to petroleum-based polymers.Vegetable oils are considered to be among the most promising renewable raw materials for polymers, because of their ready availability, inherent biodegradability, and their many versatile applications. Research on and development of vegetable oil based polymeric materials, including thermosetting resins, biocomposites, and nanocomposites, have attracted increasing attention in recent years. This Minireview focuses on the latest developments in the preparation, properties, and applications of vegetable oil based polymeric materials obtained by free radical, cationic, and olefin metathesis polymerizations. The novel vegetable oil based polymeric materials obtained range from soft rubbery materials to ductile or rigid plastics and to high-performance biocomposites and nanocomposites. These vegetable oil based polymeric materials display a wide range of thermophysical and mechanical properties and should find useful applications as alternatives to their petroleum-based counterparts.

Biological and Clinical Aspects of an Olive Oil-Based Lipid Emulsion-A Review.

PubMed

Cai, Wei; Calder, Phillip C; Cury-Boaventura, Maria F; De Waele, Elisabeth; Jakubowski, Julie; Zaloga, Gary

2018-06-15

Intravenous lipid emulsions (ILEs) have been an integral component of parenteral nutrition for more than 50 years. Numerous formulations are available and are based on vegetable (soybean, olive, coconut) and animal (fish) oils. Therefore, each of these formulations has a unique fatty acid composition that offers both benefits and limitations. As clinical experience and our understanding of the effects of fatty acids on various physiological processes has grown, there is evidence to suggest that some ILEs may have benefits compared with others. Current evidence suggests that olive oil-based ILE may preserve immune, hepatobiliary, and endothelial cell function, and may reduce lipid peroxidation and plasma lipid levels. There is good evidence from a large randomized controlled study to support a benefit of olive oil-based ILE over soybean oil-based ILE on reducing infections in critically ill patients. At present there is limited evidence to demonstrate a benefit of olive oil-based ILE over other ILEs on glucose metabolism, and few data exist to demonstrate a benefit on clinical outcomes such as hospital or intensive care unit stay, duration of mechanical ventilation, or mortality. We review the current research and clinical evidence supporting the potential positive biological and clinical aspects of olive oil-based ILE and conclude that olive oil-based ILE is well tolerated and provides effective nutritional support to various PN-requiring patient populations. Olive oil-based ILE appears to support the innate immune system, is associated with fewer infections, induces less lipid peroxidation, and is not associated with increased hepatobiliary or lipid disturbances. These data would suggest that olive oil-based ILE is a valuable option in various PN-requiring patient populations.

A volcanic connection between the Pennsylvanian of the Mid-Continent and Appalachian regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyons, P.C.; Congdon, R.D.; Outerbridge, W.F.

1993-02-01

Until now, it has not been possible to find key beds that precisely connect the Pennsylvanian section in the Mid-Continent and Appalachian regions. Altered volcanic ash deposits (tonsteins) offer the potential for high-precision stratigraphic correlation. The Fire Clay tonstein which is chemically distinct from the other five Middle Pennsylvanian tonstein beds in the central Appalachian basin, has a unimodal, rhyolitic fingerprint'' based on glass-inclusion data (n = 109) from volcanic quartz. This tonstein has been correlated over a distance of about 400 km in KY, WV, VA, and TN. Analyses of glass inclusions (n = 12) in volcanic quartz frommore » a mixed-layer (illite/smectite) tonstein (K-bentonite) from near the Morrowan-Atokan boundary, recovered from cuttings in Arkansas wells (Phillips Petroleum Co., [number sign]2, Johnson City; Carter Oil Co., [number sign]1 Williams, Conway City), are identical, within the limits of analytical precision, to those from the Fire Clay tonstein.« less

Polymeric water filtration membranes

NASA Astrophysics Data System (ADS)

Paul, Mou

Nanofiltration (NF) membranes are used for separating salts and small neutral molecules. NF membranes show unique selectivity properties compared to reverse osmosis membranes as it can selectively pass monovalent salts and neutral molecules as a function of charge and molecular weight cut-off which are dependent on membrane characteristics and operating conditions. Dow Water and Process solutions has been a pioneer in the membrane based water purification field and Dow's role was instrumental in developing several NF membranes for different applications. However, the characterization of NF membranes and hence the development of structure-property relationship is challenging due to the nanoscale thin, crosslinked nature of the membrane. Recently significant efforts were employed to develop analytical capabilities to understand polymer structure and composition and it had been possible to achieve a structure-property relationship for NF membranes. This paper will highlight similar relationships and will also focus on the relationships of membrane structure with membrane transport properties and how this relationship influences products for different application areas such as in oil field, sweetener and minimum liquid discharge etc.

Slicing of silicon into sheet material: Silicon sheet growth development for the large area silicon sheet task of the Low Cost Silicon Solar Array project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1978-01-01

The limits of blade tolerance were defined. The standard blades are T-2 thickness tolerance. Good results were obtained by using a slurry fluid consisting of mineral oil and a lubricity additive. Adjustments of the formulation and fine tuning of the cutting process with the new fluid are necessary. Test results and consultation indicate that the blade breakage encountered with water based slurries is unavoidable. Two full capacity (974 wafer) runs were made on the large prototype saw. Both runs resulted in extremely low yield. However, the reasons for the low yield were lack of proper technique rather than problems with machine function. The test on the effect of amount of material etched off of an as-sawn wafer on solar cell efficiency were completed. The results agree with previous work at JPL in that the minimum material removed per side that gives maximum efficiency is on the order of 10 microns.

Large-scale Manufacturing of Nanoparticulate-based Lubrication Additives for Improved Energy Efficiency and Reduced Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdemir, Ali

This project was funded under the Department of Energy (DOE) Lab Call on Nanomanufacturing for Energy Efficiency and was directed toward the development of novel boron-based nanocolloidal lubrication additives for improving the friction and wear performance of machine components in a wide range of industrial and transportation applications. Argonne's research team concentrated on the scientific and technical aspects of the project, using a range of state-of-the art analytical and tribological test facilities. Argonne has extensive past experience and expertise in working with boron-based solid and liquid lubrication additives, and has intellectual property ownership of several. There were two industrial collaboratorsmore » in this project: Ashland Oil (represented by its Valvoline subsidiary) and Primet Precision Materials, Inc. (a leading nanomaterials company). There was also a sub-contract with the University of Arkansas. The major objectives of the project were to develop novel boron-based nanocolloidal lubrication additives and to optimize and verify their performance under boundary-lubricated sliding conditions. The project also tackled problems related to colloidal dispersion, larger-scale manufacturing and blending of nano-additives with base carrier oils. Other important issues dealt with in the project were determination of the optimum size and concentration of the particles and compatibility with various base fluids and/or additives. Boron-based particulate additives considered in this project included boric acid (H{sub 3}BO{sub 3}), hexagonal boron nitride (h-BN), boron oxide, and borax. As part of this project, we also explored a hybrid MoS{sub 2} + boric acid formulation approach for more effective lubrication and reported the results. The major motivation behind this work was to reduce energy losses related to friction and wear in a wide spectrum of mechanical systems and thereby reduce our dependence on imported oil. Growing concern over greenhouse gas emissions was also a major reason. The transportation sector alone consumes about 13 million barrels of crude oil per day (nearly 60% of which is imported) and is responsible for about 30% of the CO{sub 2} emission. When we consider manufacturing and other energy-intensive industrial processes, the amount of petroleum being consumed due to friction and wear reaches more than 20 million barrels per day (from official energy statistics, U.S. Energy Information Administration). Frequent remanufacturing and/or replacement of worn parts due to friction-, wear-, and scuffing-related degradations also consume significant amounts of energy and give rise to additional CO{sub 2} emission. Overall, the total annual cost of friction- and wear-related energy and material losses is estimated to be rather significant (i.e., as much as 5% of the gross national products of highly industrialized nations). It is projected that more than half of the total friction- and wear-related energy losses can be recovered by developing and implementing advanced friction and wear control technologies. In transportation vehicles alone, 10% to 15% of the fuel energy is spent to overcome friction. If we can cut down the friction- and wear-related energy losses by half, then we can potentially save up to 1.5 million barrels of petroleum per day. Also, less friction and wear would mean less energy consumption as well as less carbon emissions and hazardous byproducts being generated and released to the environment. New and more robust anti-friction and -wear control technologies may thus have a significant positive impact on improving the efficiency and environmental cleanliness of the current legacy fleet and future transportation systems. Effective control of friction in other industrial sectors such as manufacturing, power generation, mining and oil exploration, and agricultural and earthmoving machinery may bring more energy savings. Therefore, this project was timely and responsive to the energy and environmental objectives of DOE and our nation. In this project, most of the boron-based materials with known and potential anti-friction and -wear properties have been manufactured as colloidal additives and tested for their effectiveness in controlling friction and wear. Unlike other anti-friction and -wear additives, which consist of zinc, molybdenum, sulfur, phosphorus, and even chlorine, lubricious boron compounds considered in this project are made of boron, oxygen, nitrogen, and hydrogen, which are more environmentally benign. Among others, boric acid is a natural mineral (known in mineralogy as "sassolite"). Based on our earlier exploratory research, it was found to offer the best overall prospect in terms of performance improvements, environmental friendliness, and ease of manufacturing and, hence, cost effectiveness. Hexagonal boron nitride and borax also offered good prospects for improving the tribological properties of lubricated sliding surfaces. Boron oxide particles were found to be rather hard and somewhat abrasive and, hence, were not considered beyond the initial screening studies. In our bench-top tribological evaluation, we also demonstrated that those additives which worked well with engine oils could work equally well with very common gear oils. When added at appropriate concentrations, such gear oils were found to provide significant resistance to micropitting and scuffing failures in bench-top tribological test systems. Their traction coefficients were also reduced substantially and their scuffing limits were improved considerably. Such impressive tribological behavior of boron-based additives may have been due to their high chemical affinities to interact with sliding contact surfaces and to form slick and protective boundary films. Indeed, our surface studies have confirmed that most of the boron-based nanoparticulate additives prepared in our project possess a strong tendency to form a boron-rich boundary film on sliding contact surfaces. It is believed that the formation of such slick and highly durable boundary films is perhaps one of the fundamental reasons for their superior anti-friction, -wear, and -scuffing performance. Boron-based additives developed under this project have shown potential to reduce or replace the uses of environmentally unsafe sulfur- and phosphorus-bearing anti-wear and friction additives, such as zinc dialkyl dithiophosphate (ZDDP) and molybdenum dialkyl dithiocarbamate (MoDTC), in current lubricating oils. Because ZDDP and MoDTC were suspected of adversely impacting the performance of after-treatment catalysts in current engines, the Environmental Protection Agency (EPA) and other regulatory agencies are demanding that the concentrations of these catalysts in current oils be curtailed drastically. The boron-based nano-additives developed in this project may help reduce the use of ZDDP and MoDTC additives and, hence, help ease the poisoning effects on after-treatment catalysts. When used as lubricity additives, these boron additives can chemically interact with sliding or contacting surfaces and form a protective and slick boundary film, which can, in turn, help reduce friction and wear and increase resistance to scuffing. In the cases of traditional anti-friction and -wear additives mentioned, such protective boundary films result from phosphorus, sulfur, and other elements in the additive package, and again they have been under increased scrutiny in recent years, mainly because of their adverse effects on after-treatment devices. Overall, the boron-based nano-additive technology of this project was shown to hold promise for a broad range of industrial and transportation applications where lower friction and higher resistance to wear and scuffing are needed. Due to more stringent operating conditions of modern machinery, rolling, rotating, and sliding components have been failing to meet the projected lifetimes, mainly because of failures related to mechanical wear, corrosion, and scuffing. The novel boron-based additive technology developed under this project may help such machine components to function reliably by cutting down the friction and wear losses and by increasing resistance to scuffing.« less

Finding the multipath propagation of multivariable crude oil prices using a wavelet-based network approach

NASA Astrophysics Data System (ADS)

Jia, Xiaoliang; An, Haizhong; Sun, Xiaoqi; Huang, Xuan; Gao, Xiangyun

2016-04-01

The globalization and regionalization of crude oil trade inevitably give rise to the difference of crude oil prices. The understanding of the pattern of the crude oil prices' mutual propagation is essential for analyzing the development of global oil trade. Previous research has focused mainly on the fuzzy long- or short-term one-to-one propagation of bivariate oil prices, generally ignoring various patterns of periodical multivariate propagation. This study presents a wavelet-based network approach to help uncover the multipath propagation of multivariable crude oil prices in a joint time-frequency period. The weekly oil spot prices of the OPEC member states from June 1999 to March 2011 are adopted as the sample data. First, we used wavelet analysis to find different subseries based on an optimal decomposing scale to describe the periodical feature of the original oil price time series. Second, a complex network model was constructed based on an optimal threshold selection to describe the structural feature of multivariable oil prices. Third, Bayesian network analysis (BNA) was conducted to find the probability causal relationship based on periodical structural features to describe the various patterns of periodical multivariable propagation. Finally, the significance of the leading and intermediary oil prices is discussed. These findings are beneficial for the implementation of periodical target-oriented pricing policies and investment strategies.

Oil Spill Map for Indian Sea Region based on Bhuvan- Geographic Information System using Satellite Images

NASA Astrophysics Data System (ADS)

Vijaya kumar, L. J.; Kishore, J. K.; Kesava Rao, P.; Annadurai, M.; Dutt, C. B. S.; Hanumantha Rao, K.; Sasamal, S. K.; Arulraj, M.; Prasad, A. V. V.; Kumari, E. V. S. Sita; Satyanarayana, S. N.; Shenoy, H. P.

2014-11-01

Oil spills in the ocean are a serious marine disaster that needs regular monitoring for environmental risk assessment and mitigation. Recent use of Polarimetric SAR imagery in near real time oil spill detection systems is associated with attempts towards automatic and unambiguous oil spill detection based on decomposition methods. Such systems integrate remote sensing technology, geo information, communication system, hardware and software systems to provide key information for analysis and decision making. Geographic information systems (GIS) like BHUVAN can significantly contribute to oil spill management based on Synthetic Aperture Radar (SAR) images. India has long coast line from Gujarat to Bengal and hundreds of ports. The increase in shipping also increases the risk of oil spills in our maritime zone. The availability of RISAT-1 SAR images enhances the scope to monitor oil spills and develop GIS on Bhuvan which can be accessed by all the users, such as ships, coast guard, environmentalists etc., The GIS enables realization of oil spill maps based on integration of the geographical, remote sensing, oil & gas production/infrastructure data and slick signatures detected by SAR. SAR and GIS technologies can significantly improve the realization of oil spill footprint distribution maps. Preliminary assessment shows that the Bhuvan promises to be an ideal solution to understand spatial, temporal occurrence of oil spills in the marine atlas of India. The oil spill maps on Bhuvan based GIS facility will help the ONGC and Coast Guard organization.

Geochemical Aspects of Formation of Large Oil Deposits in the Volga-Ural Sedimentary Basin

NASA Astrophysics Data System (ADS)

Plotnikova, I.; Nosova, F.; Pronin, N.; Nosova, J.; Budkevich, T.

2012-04-01

The study of the rocks domanikoid type in the territory of the Ural-Volga region has an almost century-long history, beginning with the first studies of A.D. Archangelsky in the late 20's of last century. But nevertheless the question of the source of oil that formed the industrial deposits of Volga-Ural oil and gas province (OGP), where Romashkinskoye oil field occupies a special place, remains unresolved and topical. According to the sedimentary-migration theory of origin of oil and gas, it is supposed that the primary source of hydrocarbons in this area are the deposits of domanikoid type that contain a large ammount of sapropel organic matter (OM). Semiluki (domanik) horizon of srednefranski substage of the Upper Devonian is considered to be a typical domanikoid stratum. Investigation of the OM of the rocks and oils of the sedimentary cover on the basis of chromato-mass spectrometry method allows us to study the correlations between rock and oil and to assess the location (or absence) of the sources of hydrocarbons in the Paleozoic sedimentary cover. The results of geochemical study of dispersed organic matter (DOM) of rocks from Semiluksky horizon of the Upper Devonian and of the oil from Pashiysky horizon of the Middle Devonian form the basis of this paper. The objectives of this study were the following: to determine the original organic matter of the rocks, which would indicate the conditions of sedimentation of the supposed rock-oil sources; the study of chemofossils (biomarkers) in oil from Pashiyskiy horizon; and the identification of genetic association of DOM rocks from Semiluksky horizon with this oil on the basis of the oil-DOM correlation. The study of biomarkers was carried out with the help of chromato-mass spectrometry in the Laboratory of Geochemistry of Fossil Fuels (Kazan Federal University). In this study we used several informative parameters characterizing the depositional environment, the type of source OM and its maturity: STER / PENT, hC35/hC34, GAM / HOP, S27/S28/S29 (steranes), DIA / REG, Ts / Tm, MOR / HOP, NOR / HOP, TET / TRI, C29SSR, C29BBAA, C31HSR, S30STER, TRI / PENT, TRI / HOP. Comparison in the rock-oil system was performed primarily according to the parameters indicating the depositional environment of the source rock that contains syngenetic DOM - according to the coefficients that determine lithological conditions for the formation of the supposed oil-source bed strata (DIA / REG, Ts / Tm, NOR / HOP, TRI / HOP and STER / PENT). Biomarker ratios indicate a different type of sedimentation basins. Sediments, which accumulated DOM from Semilukskiy horizon, can be characterized by low clay content, or its absence, that is consistent with the carbonate type of cut of the horizon. The bacterial material that was accumulated under reducing conditions of sedimentation appeared to be the source of syngenetic OM. Chemofossils found in oils from Pashiyskiy horizon are typical of sedimentary strata that contain clay - for clastic rocks, which in the study area are mainly represented by deposits and Eyfel Givetian layers of the Middle Devonian and lowfransk substage of the Upper Devonian. The study of correlations obtained for the different coefficients of OM and oils showed that only the relationships between Ts/Tm and DIA/REG and between NOR/HOP and TRI/HOP are characteristic of close, almost similar values of correlation both for the dispersed organic matter and for oil. In all other cases, the character of the correlation of OM is significantly different from that of oil. The differences in values and ranges of biomarker ratios as well as the character of their correlation indicates the absence of genetic connection between the oil from Pashiyskiy horizon for the dispersed organic matter from Semilukskiy horizon. This conclusion is based on the study of five biomarker parameters (DIA/REG, Ts/Tm, NOR/HOP, TRI/HOP and STER/PENT). The research results described in the article clearly indicate the need for further studies of geochemical features of the organic matter of the Paleozoic mantle rocks and the underlying sedimentary and crystalline complexes of Precambrian.

Investigating the CO 2 laser cutting parameters of MDF wood composite material

NASA Astrophysics Data System (ADS)

Eltawahni, H. A.; Olabi, A. G.; Benyounis, K. Y.

2011-04-01

Laser cutting of medium density fibreboard (MDF) is a complicated process and the selection of the process parameters combinations is essential to get the highest quality cut section. This paper presents a means for selecting the process parameters for laser cutting of MDF based on the design of experiments (DOE) approach. A CO 2 laser was used to cut three thicknesses, 4, 6 and 9 mm, of MDF panels. The process factors investigated are: laser power, cutting speed, air pressure and focal point position. In this work, cutting quality was evaluated by measuring the upper kerf width, the lower kerf width, the ratio between the upper kerf width to the lower kerf width, the cut section roughness and the operating cost. The effect of each factor on the quality measures was determined. The optimal cutting combinations were presented in favours of high quality process output and in favours of low cutting cost.

Vision-based Nano Robotic System for High-throughput Non-embedded Cell Cutting

NASA Astrophysics Data System (ADS)

Shang, Wanfeng; Lu, Haojian; Wan, Wenfeng; Fukuda, Toshio; Shen, Yajing

2016-03-01

Cell cutting is a significant task in biology study, but the highly productive non-embedded cell cutting is still a big challenge for current techniques. This paper proposes a vision-based nano robotic system and then realizes automatic non-embedded cell cutting with this system. First, the nano robotic system is developed and integrated with a nanoknife inside an environmental scanning electron microscopy (ESEM). Then, the positions of the nanoknife and the single cell are recognized, and the distance between them is calculated dynamically based on image processing. To guarantee the positioning accuracy and the working efficiency, we propose a distance-regulated speed adapting strategy, in which the moving speed is adjusted intelligently based on the distance between the nanoknife and the target cell. The results indicate that the automatic non-embedded cutting is able to be achieved within 1-2 mins with low invasion benefiting from the high precise nanorobot system and the sharp edge of nanoknife. This research paves a way for the high-throughput cell cutting at cell’s natural condition, which is expected to make significant impact on the biology studies, especially for the in-situ analysis at cellular and subcellular scale, such as cell interaction investigation, neural signal transduction and low invasive cell surgery.

Rising floodwaters: mapping impacts and perceptions of flooding in Indonesian Borneo

NASA Astrophysics Data System (ADS)

Wells, Jessie A.; Wilson, Kerrie A.; Abram, Nicola K.; Nunn, Malcolm; Gaveau, David L. A.; Runting, Rebecca K.; Tarniati, Nina; Mengersen, Kerrie L.; Meijaard, Erik

2016-06-01

The roles of forest and wetland ecosystems in regulating flooding have drawn increasing attention in the contexts of climate change adaptation and disaster risk reduction. However, data on floods are scarce in many of the countries where people are most exposed and vulnerable to their impacts. Here, our separate analyses of village interview surveys (364 villages) and news archives (16 sources) show that floods have major impacts on lives and livelihoods in Indonesian Borneo, and flooding risks are associated with features of the local climate and landscape, particularly land uses that have seen rapid expansions over the past 30 years. In contrast with government assessments, we find that flooding is far more widespread, and that frequent, local, events can have large cumulative impacts. Over three years, local news agencies reported floods that affected 868 settlements, 966 times (including 89 in urban areas), inundated at least 197 000 houses, and displaced more than 776 000 people, possibly as many as 1.5 million (i.e. 5%-10% of the total population). Spatial analyses based on surveys in 364 villages show that flood frequency is associated with land use in catchment areas, including forest cover and condition, and the area of wetlands, mines (open-cut coal or gold mines), and oil palm. The probability that floods have become more frequent over the past 30 years was higher for villages closer to mines, and in watersheds with more extensive oil palm, but lower in watersheds with greater cover of selectively-logged or intact forests. We demonstrate that in data-poor regions, multiple sources of information can be integrated to gain insights into the hydrological services provided by forest and wetland ecosystems, and motivate more comprehensive assessment of flooding risks and options for ecosystem-based adaptation.

Sequence stratigraphy of the Raha Formation, Bakr Oil Field, Gulf of Suez, Egypt: Insights from electrical well log and palynological data

NASA Astrophysics Data System (ADS)

Mansour, Ahmed; Mohamed, Omar; Tahoun, Sameh S.; Elewa, Ashraf M. T.

2018-03-01

The current paper provides a high resolution sequence stratigraphic study of the Raha Formation from the productive Bakr Oil Field, central Gulf of Suez, Egypt. Sixty cutting rock samples spanning the Cenomanian from three wells (Bakr-114, B-115 and B-109) in the Bakr Basin, were palynologically investigated. The documented palynomorphs assemblage of either terrestrially-derived sporomorphs or marine inhabited dinocysts, allowed two palynological zones as well as their encompassing depositional palaeoenvironment to be recognized. These zones are Afropollis jardinus-Crybelosporites pannuceus Assemblage Zone (early-middle Cenomanian) and Classopollis brasiliensis-Tricolpites sagax Assemblage Zone (late Cenomanian). Detailed analysis of the particulate organic matter compositions suggested that the depositional palaeoenvironment of the Raha Formation was fluctuating between supratidal and distal-inner neritic conditions, due to successive oscillations of the Neo-Tethyan Ocean during the Cenomanian. The pronounced peaks of particulate organic matter versus gamma ray are markedly used in delineating the depositional sequences of the Raha Formation and their bounding surfaces. The Raha Formation probably corresponds to a second-order depositional sequence, which can be further subdivided into eight third-order depositional sequences, of which six are complete and two are incomplete ones. These depositional sequences are significantly synchronized based on a simple 2-D correlation model between the three wells. According to the hierarchical duration system, the Cenomanian herein was approximately attributed to 6 Myr, each of which has lower order depositional sequences that took approximately 0.9 Myr. Based on the sequence stratigraphic approach together with palynofacies analysis and gamma ray data, a condensed section was defined in the B-115.

ALPS yield optimization cutting program

Treesearch

P. Klinkhachorn; J.P. Franklin; Charles W. McMillin; H.A. Huber

1989-01-01

This paper reports ongoing work on a series of computer programs developed to automate hardwood lumber processing in a furniture roughmill. The program computes the placement of cuttings on lumber, based on a description of each board in terms of shape and defect location, and a cutting bill. These results are suitable for use with a high-power laser to cut the parts...

Kolkhoung (Pistacia khinjuk) Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability 
and Nutritional Value.

PubMed

Asnaashari, Maryam; Hashemi, Seyed Mohammad Bagher; Mehr, Hamed Mahdavian; Yousefabad, Seyed Hossein Asadi

2015-03-01

In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high-performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel) and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well--balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation-sensitive oils to improve their shelf life.

Optical characterization of pure vegetable oils and their biodiesels using Raman spectroscopy

NASA Astrophysics Data System (ADS)

Firdous, S.; Anwar, S.; Waheed, A.; Maraj, M.

2016-04-01

Great concern regarding energy resources and environmental polution has increased interest in the study of alternative sources of energy. Biodiesels as an alternative fuel provide a suitable diesel oil substitute for internal combustion engines. The Raman spectra of pure biodiesels of soybean oil, olive oil, coconut oil, animal fats, and petroleum diesel are optically characterized for quality and biofuel as an alternative fuel. The most significant spectral differences are observed in the frequency range around 1457 cm-1 for pure petroleum diesel, 1427 for fats biodiesel, 1670 cm-1 for pure soybean oil, 1461 cm-1 for soybean oil based biodiesel, 1670 cm-1 for pure olive oil, 1666 cm-1 for olive oil based biodiesel, 1461 cm-1 for pure coconut oil, and 1460 cm-1 for coconut oil based biodiesel, which is used for the analysis of the phase composition of oils. A diode pump solid-state laser with a 532 nm wavelength is used as an illuminating light. It is demonstrated that the peak positions and relative intensities of the vibrations of the oils can be used to identify the biodiesel quality for being used as biofuel.

Modeling and analysis of the chip formation and transient cutting force during elliptical vibration cutting process

NASA Astrophysics Data System (ADS)

Lin, Jieqiong; Guan, Liang; Lu, Mingming; Han, Jinguo; Kan, Yudi

2017-12-01

In traditional diamond cutting, the cutting force is usually large and it will affect tool life and machining quality. Elliptical vibration cutting (EVC) as one of the ultra-precision machining technologies has a lot of advantages, such as reduces cutting force, extend tool life and so on. It's difficult to predict the transient cutting force of EVC due to its unique elliptical motion trajectory. Study on chip formation will helpfully to predict cutting force. The geometric feature of chip has important effects on cutting force, however, few scholars have studied the chip formation. In order to investigate the time-varying cutting force of EVC, the geometric feature model of chip is established based on analysis of chip formation, and the effects of cutting parameters on the geometric feature of chip are analyzed. To predict transient force quickly and effectively, the geometric feature of chip is introduced into the cutting force model. The calculated results show that the error between the predicted cutting force in this paper and that in the literature is less than 2%, which proves its feasibility.

Experimental analysis of Nd-YAG laser cutting of sheet materials - A review

NASA Astrophysics Data System (ADS)

Sharma, Amit; Yadava, Vinod

2018-01-01

Cutting of sheet material is considered as an important process due to its relevance among products of everyday life such as aircrafts, ships, cars, furniture etc. Among various sheet cutting processes (ASCPs), laser beam cutting is one of the most capable ASCP to create complex geometries with stringent design requirements in difficult-to-cut sheet materials. Based on the recent research work in the area of sheet cutting, it is found that the Nd-YAG laser is used for cutting of sheet material in general and reflective sheet material in particular. This paper reviews the experimental analysis of Nd-YAG laser cutting process, carried out to study the influence of laser cutting parameters on the process performance index. The significance of experimental modeling and different optimization approaches employed by various researchers has also been discussed in this study.

CO₂ emission mitigation and fossil fuel markets: Dynamic and international aspects of climate policies

DOE PAGES

Bauer, Nico; Bosetti, Valentina; Hamdi-Cherif, Meriem; ...

2015-01-01

This paper explores a multi-model scenario ensemble to assess the impacts of idealized and non-idealized climate change stabilization policies on fossil fuel markets. Under idealized conditions climate policies significantly reduce coal use in the short- and long-term. Reductions in oil and gas use are much smaller, particularly until 2030, but revenues decrease much more because oil and gas prices are higher than coal prices. A first deviation from optimal transition pathways is delayed action that relaxes global emission targets until 2030 in accordance with the Copenhagen pledges. Fossil fuel markets revert back to the no-policy case: though coal use increasesmore » strongest, revenue gains are higher for oil and gas. To balance the carbon budget over the 21st century, the long-term reallocation of fossil fuels is significantly larger—twice and more—than the short-term distortion. This amplifying effect results from coal lock-in and inter-fuel substitution effects to balance the full-century carbon budget. The second deviation from the optimal transition pathway relaxes the global participation assumption. The result here is less clear-cut across models, as we find carbon leakage effects ranging from positive to negative because trade and substitution patterns of coal, oil, and gas differ across models. In summary, distortions of fossil fuel markets resulting from relaxed short-term global emission targets are more important and less uncertain than the issue of carbon leakage from early mover action.« less

CO₂ emission mitigation and fossil fuel markets: Dynamic and international aspects of climate policies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Nico; Bosetti, Valentina; Hamdi-Cherif, Meriem

This paper explores a multi-model scenario ensemble to assess the impacts of idealized and non-idealized climate change stabilization policies on fossil fuel markets. Under idealized conditions climate policies significantly reduce coal use in the short- and long-term. Reductions in oil and gas use are much smaller, particularly until 2030, but revenues decrease much more because oil and gas prices are higher than coal prices. A first deviation from optimal transition pathways is delayed action that relaxes global emission targets until 2030 in accordance with the Copenhagen pledges. Fossil fuel markets revert back to the no-policy case: though coal use increasesmore » strongest, revenue gains are higher for oil and gas. To balance the carbon budget over the 21st century, the long-term reallocation of fossil fuels is significantly larger—twice and more—than the short-term distortion. This amplifying effect results from coal lock-in and inter-fuel substitution effects to balance the full-century carbon budget. The second deviation from the optimal transition pathway relaxes the global participation assumption. The result here is less clear-cut across models, as we find carbon leakage effects ranging from positive to negative because trade and substitution patterns of coal, oil, and gas differ across models. In summary, distortions of fossil fuel markets resulting from relaxed short-term global emission targets are more important and less uncertain than the issue of carbon leakage from early mover action.« less

CO2 emissions mitigation and fossil fuel markets: Dynamic and international aspects of climate policies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Nico; Bosetti, Valentina; Hamdi-Cherif, Meriem

This paper explores a multi-model scenario ensemble to assess the impacts of idealized and non-idealized climate change stabilization policies on fossil fuel markets. Under idealized conditions climate policies significantly reduce coal use in the short- and long-term. Reductions in oil and gas use are much smaller, particularly until 2030, but revenues decrease much more because oil and gas prices are higher and decrease with mitigation. A first deviation from the optimal transition pathway relaxes global emission targets until 2030, in accordance with the Copenhagen pledges and regionally-specific low-carbon technology targets. Fossil fuel markets revert back to the no-policy case: thoughmore » coal use increases strongest, revenue gains are higher for oil and gas. To balance the carbon budget over the 21st century, the long-term reallocation of fossil fuels is significantly larger - twice and more - than the short-term distortion. This amplifying effect results from coal lock-in and inter-fuel substitution effects. The second deviation from the optimal transition pathway relaxes the global participation assumption. The result here is less clear cut across models, as we find carbon leakage effects ranging from positive to negative because leakage and substitution patterns of coal, oil, and gas differ. In summary, distortions of fossil fuel markets resulting from relaxed short-term global emission targets are more important and less uncertain than the issue of carbon leakage from early mover action.« less

Motor Oil Classification Based on Time-Resolved Fluorescence

PubMed Central

Mu, Taotao; Chen, Siying; Zhang, Yinchao; Guo, Pan; Chen, He; Meng, Fandong

2014-01-01

A time-resolved fluorescence (TRF) technique is presented for classifying motor oils. The system is constructed with a third harmonic Nd:YAG laser, a spectrometer, and an intensified charge coupled device (ICCD) camera. Steady-state and time-resolved fluorescence (TRF) measurements are reported for several motor oils. It is found that steady-state fluorescence is insufficient to distinguish the motor oil samples. Then contour diagrams of TRF intensities (CDTRFIs) are acquired to serve as unique fingerprints to identify motor oils by using the distinct TRF of motor oils. CDTRFIs are preferable to steady-state fluorescence spectra for classifying different motor oils, making CDTRFIs a particularly choice for the development of fluorescence-based methods for the discrimination and characterization of motor oils. The two-dimensional fluorescence contour diagrams contain more information, not only the changing shapes of the LIF spectra but also the relative intensity. The results indicate that motor oils can be differentiated based on the new proposed method, which provides reliable methods for analyzing and classifying motor oils. PMID:24988439

Impact assisted segmented cutterhead

DOEpatents

Morrell, Roger J.; Larson, David A.; Ruzzi, Peter L.

1992-01-01

An impact assisted segmented cutterhead device is provided for cutting various surfaces from coal to granite. The device comprises a plurality of cutting bit segments deployed in side by side relationship to form a continuous cutting face and a plurality of impactors individually associated with respective cutting bit segments. An impactor rod of each impactor connects that impactor to the corresponding cutting bit segment. A plurality of shock mounts dampening the vibration from the associated impactor. Mounting brackets are used in mounting the cutterhead to a base machine.

Inhibitory Effects of Pterodon emarginatus Bean Oil and Extract on Staphylococcus aureus

PubMed Central

Mendes, V. S.; Sant'Anna, J. B.; Oliveira, S. C. C.; Maldonade, Iriani Rodrigues; Machado, Eleuza Rodrigues

2017-01-01

Background: Pterodon emarginatus is a tree of the Brazilian Savannah. The beans of this tree are used in folk medicine as anti-inflammatory preparations, especially for infections caused by Staphylococcus aureus. These bacteria can cause simple infections or serious illnesses such as pneumonia, meningitis, endocarditis, toxic shock syndrome, septicemia, and others. Objective: This study had the goal of verifying the effect of the essential oil (OE) from P. emarginatus on the inhibition of S. aureus in culture medium, i.e., “ in vitro” tests. Materials and Methods: The vegetable material was cut and crushed with a press. The OE was obtained by extraction using hexane, alcohol, and water. The P. emarginatus extracts obtained were used to evaluate the antimicrobial effect on S. aureus (ATCC 25923) by tests of well diffusion, disc diffusion, and microdilution. The strain used in the assays was maintained in brain heart infusion broth and nutrient agar until testing. Afterward, the bacteria were spread on agar plates with Mueller-Hinton agar medium. In the wells and on the paper discs, the OE suspensions were placed in the following volumes: 10, 15, 20, 25, 30, 40, and 80 μL and subsequently they were incubated at 35°C ± 2°C. After 24 h, the number of colony-forming unit was determined. Results: Pure OE and hydroalcoholic extract inhibited the growth of S. aureus, while aqueous extract had no effect on bacterial growth in all microbial methods used. Conclusion: Thus, the present study showed the potential of sucupira-based extracts against S. aureus growth, opening new perspectives for the evaluation of these bioactive compounds as phytopharmaceutical products. SUMMARY Plant extract act as antimicrobials to prevent and reduce bacterial contaminationBeans of Pterodon emarginatus has antibacterial propertiesExtraction with different solvents might implicate on the rate of bacterial deathThe effect of different microbiological methods (well diffusion, disc diffusion and microdilution) was evaluated on reducing CFUThe results showed by MBC that concentrations superior to 10% (v/v) using AC and 7.5% (v/v) using OE were necessary to eliminate colonies formedAccording to data of MIC, at 2.5% of AC and OE was enough to kill S. aureusThe well diffusion technique demonstrated better performance than disc diffusion test for OE and AC extractsHydroalcoholic and oil extracts of sucupira beans had highest effect against Staphylococcus aureusAqueous extract had no effect on bacterial growth in all microbial methods testedThe sucupira-based extracts is a promising source as herbal drug due to therapeutic value Abbreviations Used: OE: Essencial oil; AC: Hydroalcoholic oil extract; AQ: Aqueous extracts; MIC: Minimum inhibitory concentration; MBC: Minimum bactericidal concentration; CFU: Colony formed unit. PMID:29263627

Inhibitory Effects of Pterodon emarginatus Bean Oil and Extract on Staphylococcus aureus.

PubMed

Mendes, V S; Sant'Anna, J B; Oliveira, S C C; Maldonade, Iriani Rodrigues; Machado, Eleuza Rodrigues

2017-01-01

Pterodon emarginatus is a tree of the Brazilian Savannah. The beans of this tree are used in folk medicine as anti-inflammatory preparations, especially for infections caused by Staphylococcus aureus . These bacteria can cause simple infections or serious illnesses such as pneumonia, meningitis, endocarditis, toxic shock syndrome, septicemia, and others. This study had the goal of verifying the effect of the essential oil (OE) from P. emarginatus on the inhibition of S. aureus in culture medium, i.e., " in vitro " tests. The vegetable material was cut and crushed with a press. The OE was obtained by extraction using hexane, alcohol, and water. The P. emarginatus extracts obtained were used to evaluate the antimicrobial effect on S. aureus (ATCC 25923) by tests of well diffusion, disc diffusion, and microdilution. The strain used in the assays was maintained in brain heart infusion broth and nutrient agar until testing. Afterward, the bacteria were spread on agar plates with Mueller-Hinton agar medium. In the wells and on the paper discs, the OE suspensions were placed in the following volumes: 10, 15, 20, 25, 30, 40, and 80 μL and subsequently they were incubated at 35°C ± 2°C. After 24 h, the number of colony-forming unit was determined. Pure OE and hydroalcoholic extract inhibited the growth of S. aureus , while aqueous extract had no effect on bacterial growth in all microbial methods used. Thus, the present study showed the potential of sucupira-based extracts against S. aureus growth, opening new perspectives for the evaluation of these bioactive compounds as phytopharmaceutical products. Plant extract act as antimicrobials to prevent and reduce bacterial contaminationBeans of Pterodon emarginatus has antibacterial propertiesExtraction with different solvents might implicate on the rate of bacterial deathThe effect of different microbiological methods (well diffusion, disc diffusion and microdilution) was evaluated on reducing CFUThe results showed by MBC that concentrations superior to 10% (v/v) using AC and 7.5% (v/v) using OE were necessary to eliminate colonies formedAccording to data of MIC, at 2.5% of AC and OE was enough to kill S. aureus The well diffusion technique demonstrated better performance than disc diffusion test for OE and AC extractsHydroalcoholic and oil extracts of sucupira beans had highest effect against Staphylococcus aureus Aqueous extract had no effect on bacterial growth in all microbial methods testedThe sucupira-based extracts is a promising source as herbal drug due to therapeutic value Abbreviations Used: OE: Essencial oil; AC: Hydroalcoholic oil extract; AQ: Aqueous extracts; MIC: Minimum inhibitory concentration; MBC: Minimum bactericidal concentration; CFU: Colony formed unit.

Effect of cumin essential oil usage on fermentation quality, aerobic stability and in vitro digetibility of alfalfa silage.

PubMed

Turan, Aslı; Önenç, Sibel Soycan

2018-03-02

This study was carried out to determine the effects of cumin essential oil on the silage fermentation, aerobic stability and in vitro digestibility of alfalfa silages. Alfalfa was harvested at early bloom (5 th cutting) stage in October and wilted for about 3 hours. The research was carried out at three groups which were the control group where no additive control was done (CON), cumin essential oil (CMN3) with 300 mg/kg and CMN5 with 500 mg/kg cumin essential oil addition. Alfalfa was ensiled in plastic bags. The packages were stored at 8±2 °C under laboratory conditions. All groups were sampled for physical, chemical and microbiological analysis 120th day after ensiling. At the end of the ensiling period, all silages were subjected to an aerobic stability test for 7 days. In addition, enzimatic solubility of organic matter (ESOM), metabolizable energy (ME) and relative feed value (RFV) of these silages were determined. pH level decreased in the cumin groups compared to CON (P<0.05), thus inhibiting proteolytic enzymes from breaking down proteins into ammonia. In addition, it increased ESOM amount, and concordantly provided an increase of ME contents. Similarly, dry matter intake (DMI) and RFV ratio increased. After opening the silage, it kept its aerobic stability for three days. Cumin essential oil improved fermentation, and affected chemical and microbiological characteristics of silages. Especially the addition of 300 mg/kg cumin provided cell wall fractionation through stimulating the activities of enzymes responsible. It also increased the number and activity of lactic acid bacteri (LAB) through providing a development of LAB.

The Anti-Resonance Criterion in Selecting Pick Systems for Fully Operational Cutting Machinery Used in Mining

NASA Astrophysics Data System (ADS)

Cheluszka, Piotr

2017-12-01

This article discusses the issue of selecting a pick system for cutting mining machinery, concerning the reduction of vibrations in the cutting system, particularly in a load-carrying structure at work. Numerical analysis was performed on a telescopic roadheader boom equipped with transverse heads. A frequency range of the boom's free vibrations with a set structure and dynamic properties were determined based on a dynamic model. The main components excited by boom vibrations, generated through the process of cutting rock, were identified. This was closely associated with the stereometry of the cutting heads. The impact on the pick system (the number of picks and their arrangement along the side of the cutting head) was determined by the intensity of the external boom load elements, especially in resonance zones. In terms of the anti-resonance criterion, an advantageous system of cutting head picks was determined as a result of the analysis undertaken. The correct selection of the pick system was ascertained based on a computer simulation of the dynamic loads and vibrations of a roadheader telescopic boom.

Identification of the critical depth-of-cut through a 2D image of the cutting region resulting from taper cutting of brittle materials

NASA Astrophysics Data System (ADS)

Gu, Wen; Zhu, Zhiwei; Zhu, Wu-Le; Lu, Leyao; To, Suet; Xiao, Gaobo

2018-05-01

An automatic identification method for obtaining the critical depth-of-cut (DoC) of brittle materials with nanometric accuracy and sub-nanometric uncertainty is proposed in this paper. With this method, a two-dimensional (2D) microscopic image of the taper cutting region is captured and further processed by image analysis to extract the margin of generated micro-cracks in the imaging plane. Meanwhile, an analytical model is formulated to describe the theoretical curve of the projected cutting points on the imaging plane with respect to a specified DoC during the whole cutting process. By adopting differential evolution algorithm-based minimization, the critical DoC can be identified by minimizing the deviation between the extracted margin and the theoretical curve. The proposed method is demonstrated through both numerical simulation and experimental analysis. Compared with conventional 2D- and 3D-microscopic-image-based methods, determination of the critical DoC in this study uses the envelope profile rather than the onset point of the generated cracks, providing a more objective approach with smaller uncertainty.

Anti-wear additive content in fully synthetic PAO and PAG base oils and its effect on electrostatic and tribological phenomena in a rotating shaft-oil-lip seal system

NASA Astrophysics Data System (ADS)

Gajewski, Juliusz B.; Głogowski, Marek J.

2013-03-01

The paper presents the results of experiments on electrostatic and tribological aspects of different anti-wear additive's contents when an additive is blended with different fully synthetic (poly-α-olefin) and PAG (polyalkylene glycol) base oils in a rotating shaft-oil and oil-lip seal interfacial system. The experimental results are the relationships of electric potential induced in a lip seal's stiffening ring to angular velocity of a rotating metal shaft and to temperature of the oils tested. The braking torque of a shaft is measured with a torquemeter sensor connected directly with a microprocessor-based system for controlling the rotational speed and for measuring the shaft's braking torque and oil temperature. The beneficial and promising results are obtained for PAG when an external DC electric field is applied to the system and the braking torque is then reduced for a certain combination of the base oil and additive's contents. On the basis of the former and present research results an analysis is made to permit one to show how the type of the oils and additives tested can affect both interfaces: rotating shaft-oil and oil-lip of the lip seal and especially the braking torque.

An oil fraction neural sensor developed using electrical capacitance tomography sensor data.

PubMed

Zainal-Mokhtar, Khursiah; Mohamad-Saleh, Junita

2013-08-26

This paper presents novel research on the development of a generic intelligent oil fraction sensor based on Electrical Capacitance Tomography (ECT) data. An artificial Neural Network (ANN) has been employed as the intelligent system to sense and estimate oil fractions from the cross-sections of two-component flows comprising oil and gas in a pipeline. Previous works only focused on estimating the oil fraction in the pipeline based on fixed ECT sensor parameters. With fixed ECT design sensors, an oil fraction neural sensor can be trained to deal with ECT data based on the particular sensor parameters, hence the neural sensor is not generic. This work focuses on development of a generic neural oil fraction sensor based on training a Multi-Layer Perceptron (MLP) ANN with various ECT sensor parameters. On average, the proposed oil fraction neural sensor has shown to be able to give a mean absolute error of 3.05% for various ECT sensor sizes.

An Oil Fraction Neural Sensor Developed Using Electrical capacitance Tomography Sensor Data

PubMed Central

Zainal-Mokhtar, Khursiah; Mohamad-Saleh, Junita

2013-01-01

This paper presents novel research on the development of a generic intelligent oil fraction sensor based on Electrical capacitance Tomography (ECT) data. An artificial Neural Network (ANN) has been employed as the intelligent system to sense and estimate oil fractions from the cross-sections of two-component flows comprising oil and gas in a pipeline. Previous works only focused on estimating the oil fraction in the pipeline based on fixed ECT sensor parameters. With fixed ECT design sensors, an oil fraction neural sensor can be trained to deal with ECT data based on the particular sensor parameters, hence the neural sensor is not generic. This work focuses on development of a generic neural oil fraction sensor based on training a Multi-Layer Perceptron (MLP) ANN with various ECT sensor parameters. On average, the proposed oil fraction neural sensor has shown to be able to give a mean absolute error of 3.05% for various ECT sensor sizes. PMID:24064598

Shear rheological characterization of motor oils

NASA Technical Reports Server (NTRS)

Bair, Scott; Winer, Ward O.

1988-01-01

Measurements of high pressure viscosity, traction coefficient, and EHD film thickness were performed on twelve commercial automotive engine oils, a reference oil, two unformulated base oils and two unformated base oil and polymer blends. An effective high shear rate inlet viscosity was calculated from film thickness and pressure viscosity coefficient. The difference between measured and effective viscosity is a function of the polymer type and concentration. Traction measurements did not discriminate mileage formulated oils from those not so designated.

Feature-based and statistical methods for analyzing the Deepwater Horizon oil spill with AVIRIS imagery

USGS Publications Warehouse

Rand, R.S.; Clark, R.N.; Livo, K.E.

2011-01-01

The Deepwater Horizon oil spill covered a very large geographical area in the Gulf of Mexico creating potentially serious environmental impacts on both marine life and the coastal shorelines. Knowing the oil's areal extent and thickness as well as denoting different categories of the oil's physical state is important for assessing these impacts. High spectral resolution data in hyperspectral imagery (HSI) sensors such as Airborne Visible and Infrared Imaging Spectrometer (AVIRIS) provide a valuable source of information that can be used for analysis by semi-automatic methods for tracking an oil spill's areal extent, oil thickness, and oil categories. However, the spectral behavior of oil in water is inherently a highly non-linear and variable phenomenon that changes depending on oil thickness and oil/water ratios. For certain oil thicknesses there are well-defined absorption features, whereas for very thin films sometimes there are almost no observable features. Feature-based imaging spectroscopy methods are particularly effective at classifying materials that exhibit specific well-defined spectral absorption features. Statistical methods are effective at classifying materials with spectra that exhibit a considerable amount of variability and that do not necessarily exhibit well-defined spectral absorption features. This study investigates feature-based and statistical methods for analyzing oil spills using hyperspectral imagery. The appropriate use of each approach is investigated and a combined feature-based and statistical method is proposed.

A Case Study of Petroleum Degradation in Different Soil Textural Classes.

PubMed

Kogbara, Reginald B; Ayotamuno, Josiah M; Worlu, Daniel C; Fubara-Manuel, Isoteim

2016-01-01

Patents have been granted for a number of techniques for petroleum biodegradation including use of micro-organisms for degradation of hydrocarbon-based substances and for hydrocarbon degradation in oil reservoirs, but there is a dearth of information on hydrocarbon degradation in different soil textures. Hence, this work investigated the effects of different soil textures on degradation of petroleum hydrocarbons during a six-week period. Five soil textural classes commonly found in Port Harcourt metropolis, Nigeria, namely sand, loamy sand, sandy loam, silty clay and clay, were employed. The soils were contaminated with the same amount of crude oil and then remediated by biostimulation. Selected soil properties were monitored over time. Bacterial numbers declined significantly in the fine soil textures after petroleum contamination, but were either unaffected or increased significantly in the coarser soil textures. Hydrocarbon losses ranged from 42% - 99%; the sandy loam had the highest, while the clay soil had the least total hydrocarbon content (THC) reduction. The total heterotrophic bacterial (THB) counts generally corroborated the THC results. Fold increase in bacterial numbers due to remediation treatment decreased with increasing clay content. The results suggest that higher sand than clay content of soil favours faster hydrocarbon degradation. Hydrocarbon degradation efficiency increased with silt content among soil groupings such as fine and coarse soils but not necessarily with increasing silt content of soil. Thus, there seems to be cut-off sand and clay contents in soil at which the effect of the silt content becomes significant.

Application of game theory in decision making strategy: Does gas fuel industry need to kill oil based fuel industry?

NASA Astrophysics Data System (ADS)

Azmi, Abdul Luky Shofi'ul; Prabandari, Dyah Lusiana; Hakim, Muhammad Lintang Islami

2017-03-01

Even though conversion of oil based fuel (Bahan Bakar Minyak) into gas fuel (Bahan Bakar Gas) for transportation (both land and sea) is one of the priority programs of the government of Indonesia, rules that have been established merely basic rules of gas fuel usage license for transportation, without discussing position of gas fuel related to oil based fuel in detail. This paper focus on possible strategic behavior of the key players in the oil-gas fuel conversion game, who will be impacted by the position of gas fuel as complement or substitution of oil based fuel. These players include industry of oil based fuel, industry of gas fuel, and the government. Modeling is made based on two different conditions: government plays a passive role and government plays an active role in legislating additional rules that may benefit industry of gas fuel. Results obtained under a passive government is that industry of oil based fuel need to accommodate the presence of industry of gas fuel, and industry of gas fuel does not kill/ eliminate the oil based fuel, or gas fuel serves as a complement. While in an active government, the industry of oil based fuel need to increase its negotiation spending in the first phase so that the additional rule that benefitting industry of gas fuel would not be legislated, while industry of gas fuel chooses to indifferent; however, in the last stage, gas fuel turned to be competitive or choose its role to be substitution.

Detection of Cutting Tool Wear using Statistical Analysis and Regression Model

NASA Astrophysics Data System (ADS)

Ghani, Jaharah A.; Rizal, Muhammad; Nuawi, Mohd Zaki; Haron, Che Hassan Che; Ramli, Rizauddin

2010-10-01

This study presents a new method for detecting the cutting tool wear based on the measured cutting force signals. A statistical-based method called Integrated Kurtosis-based Algorithm for Z-Filter technique, called I-kaz was used for developing a regression model and 3D graphic presentation of I-kaz 3D coefficient during machining process. The machining tests were carried out using a CNC turning machine Colchester Master Tornado T4 in dry cutting condition. A Kistler 9255B dynamometer was used to measure the cutting force signals, which were transmitted, analyzed, and displayed in the DasyLab software. Various force signals from machining operation were analyzed, and each has its own I-kaz 3D coefficient. This coefficient was examined and its relationship with flank wear lands (VB) was determined. A regression model was developed due to this relationship, and results of the regression model shows that the I-kaz 3D coefficient value decreases as tool wear increases. The result then is used for real time tool wear monitoring.

Iron aluminide knife and method thereof

DOEpatents

Sikka, Vinod K.

1997-01-01

Fabricating an article of manufacture having a Fe.sub.3 Al-based alloy cutting edge. The fabrication comprises the steps of casting an Fe.sub.3 Al-based alloy, extruding into rectangular cross section, rolling into a sheet at 800.degree. C. for a period of time followed by rolling at 650.degree. C., cutting the rolled sheet into an article having an edge, and grinding the edge of the article to form a cutting edge.