Comparative advantages and limitations of the basic metrology methods applied to the characterization of nanomaterials.

PubMed

Linkov, Pavel; Artemyev, Mikhail; Efimov, Anton E; Nabiev, Igor

2013-10-07

Fabrication of modern nanomaterials and nanostructures with specific functional properties is both scientifically promising and commercially profitable. The preparation and use of nanomaterials require adequate methods for the control and characterization of their size, shape, chemical composition, crystalline structure, energy levels, pathways and dynamics of physical and chemical processes during their fabrication and further use. In this review, we discuss different instrumental methods for the analysis and metrology of materials and evaluate their advantages and limitations at the nanolevel.

CO.sub.2 removal sorbent composition with high chemical stability during multiple cycles

DOEpatents

Siriwardane, Ranjani V.; Rosencwaig, Shira

2015-09-22

Disclosed herein is a clay-alkali-amine CO.sub.2 sorbent composition prepared by integrating a clay substrate, basic alkali salt, and amine liquid. The basic alkali salt is present relative to the clay substrate in a weight ratio of from about 1 part to about 50 parts per 100 parts of the clay substrate. The amine liquid is present relative to a clay-alkali combination in a weight ratio of from about 1 part to about 10 parts per 10 parts of the clay-alkali combination. The clay-alkali-amine C02 sorbent is particularly advantageous for low temperature CO.sub.2 removal cycles in a gas stream having a C02 concentration less than around 2000 ppm and an oxygen concentration around 21%, such as air.

Premixed autoignition in compressible turbulence

NASA Astrophysics Data System (ADS)

Konduri, Aditya; Kolla, Hemanth; Krisman, Alexander; Chen, Jacqueline

2016-11-01

Prediction of chemical ignition delay in an autoignition process is critical in combustion systems like compression ignition engines and gas turbines. Often, ignition delay times measured in simple homogeneous experiments or homogeneous calculations are not representative of actual autoignition processes in complex turbulent flows. This is due the presence of turbulent mixing which results in fluctuations in thermodynamic properties as well as chemical composition. In the present study the effect of fluctuations of thermodynamic variables on the ignition delay is quantified with direct numerical simulations of compressible isotropic turbulence. A premixed syngas-air mixture is used to remove the effects of inhomogeneity in the chemical composition. Preliminary results show a significant spatial variation in the ignition delay time. We analyze the topology of autoignition kernels and identify the influence of extreme events resulting from compressibility and intermittency. The dependence of ignition delay time on Reynolds and turbulent Mach numbers is also quantified. Supported by Basic Energy Sciences, Dept of Energy, United States.

Effects of Grapevine Leafroll associated Virus 3 (GLRaV-3) and duration of infection on fruit composition and wine chemical profile of Vitis vinifera L. cv. Sauvignon blanc.

PubMed

Montero, R; Mundy, D; Albright, A; Grose, C; Trought, M C T; Cohen, D; Chooi, K M; MacDiarmid, R; Flexas, J; Bota, J

2016-04-15

In order to determine the effects of Grapevine Leafroll associated Virus 3 (GLRaV-3) on fruit composition and chemical profile of juice and wine from Vitis vinifera L. cv. Sauvignon blanc grown in New Zealand, composition variables were measured on fruit from vines either infected with GLRaV-3 (established or recent infections) or uninfected vines. Physiological ripeness (20.4°Brix) was the criterion established to determine the harvest date for each of the three treatments. Date of grape ripeness was strongly affected by virus infection. In juice and wine, GLRaV-3 infection prior to 2008 reduced titratable acidity compared with the uninfected control. Differences observed in amino acids from the three infection status groups did not modify basic wine chemical properties. In conclusion, GLRaV-3 infection slowed grape ripening, but at equivalent ripeness to result in minimal effects on the juice and wine chemistry. Time of infection produced differences in specific plant physiological variables. Copyright © 2015 Elsevier Ltd. All rights reserved.

Analysis of waste coal from the enterprises of Kemerovo region as raw materials for production of ceramic materials

NASA Astrophysics Data System (ADS)

Stolboushkin, A. Yu; Akst, D. V.; Fomina, O. A.; Ivanov, A. I.; Syromyasov, V. A.

2017-09-01

The analysis of waste coal from mining enterprises of Kemerovo region as raw materials for production of building ceramics is given. The results of studies of material, chemical and mineralogical compositions of waste coal from Abashevskaya processing plant (Novokuznetsk) are presented. It was established that the chemical composition of waste coal refers to aluminosilicate raw materials with a high content of alumina and coloring oxides, the residual carbon content in the wastes is 12-25 %. According to the granulometric composition the waste coal is basically a sandy-dusty fraction with a small amount of clay particles (1-3 %). Additional grinding of coal waste and the introduction of a clay additive in an amount of up to 30 % are recommended. The results of the study of the mineral composition of waste coal are presented. Clay minerals are represented in the descending order by hydromuscovite, montmorillonite and kaolinite, minerals-impurities consist of quartz, feldspar fine-dispersed carbonates. The results of the investigation of ceramic-technological properties of waste coal, which belong to the group of moderately plastic low-melting raw materials, are given. As a result of a comprehensive study it was been established that with chemical, granulometric and mineralogical compositions waste coal with the reduced residual carbon can be used in the production of ceramic bricks.

Preparation and characterization of bio-composite PEEK/nHA

NASA Astrophysics Data System (ADS)

Jin, Y. S.; Bian, C. C.; Zhang, Z. Q.; Zhao, Y.; Yang, L.

2017-01-01

PEEK/nHA composite material, with excellent mechanical property as polyetheretherketone (PEEK) and biological activity as hydroxyapatite (HA), has attracted wide attention of medical experts and materials science experts. The addition of hydroxyapatite was the decisive factor for biological activity in PEEK/nHA composite. In this paper, acicular nanohydroxyapatite was prepared by chemical precipitation method with Ca(NO3)2, (NH4)2HPO4 as raw material; PEEK/nHA composite was prepared by solution blending and vacuum sintering method. The composite was characterized with FT-IR, XRD, DSC, TG and mechanical property test. Results showed that the composite has good thermal stability and compressive property when the mass ratio of PEEK to nHA is 10:3; and high nHA content can improve the biological activity of the composite, which can meet the basic requirements for bone tissue engineering scaffold.

Chemical Composition and Vasorelaxant and Antispasmodic Effects of Essential Oil from Rosa indica L. Petals

PubMed Central

Rasheed, Hafiz Majid; Khan, Taous; Wahid, Fazli; Khan, Rasool; Shah, Abdul Jabbar

2015-01-01

Rosa indica L. belongs to the family Rosaceae and is locally known as gulaab. It has different traditional uses in cardiovascular and gastrointestinal disorders but there is no scientific data available in this regard. Therefore, the basic aim of this study was to explore the chemical composition and gastrointestinal and cardiovascular effects of the essential oil obtained from R. indica. The chemical composition of the essential oil was investigated using gas chromatography-mass spectrometry (GC-MS) technique. The cardiovascular and gastrointestinal effects were investigated using electrophysiological measurements. The GC-MS analysis of the essential oil showed various chemical components including acetic acid, mercaptohexyl ester, butanoic acid, 2-methyl-5-oxo-1-cyclopentene-1-yl ester, artemiseole, methyl santonilate, isosteviol, caryophyllene oxide, pentyl phenyl acetate, dihydromyrcene, 1,5-octadecadien, octadecanoic acid, ethyl ester, palmitic acid (2-phenyl-1,3-dioxolan-4-yl methyl ester), santolina epoxide, and 9-farnesene. The electrophysiological measurements revealed that essential oil was more potent against K+ (80 mM) than phenylephrine precontractions using isolated rabbit aorta preparations. In isolated rabbit jejunum preparations, it showed more potency against high K+ induced contractions than spontaneous contractions. Considering these evidences, it can be concluded that R. indica essential oil may work as a complementary and alternative medicine in gastrointestinal and cardiovascular diseases. PMID:26357519

Amino acid composition of some Mexican foods.

PubMed

Morales de León, Josefina; Camacho, M Elena; Bourges, Héctor

2005-06-01

Knowledge of the amino acid composition of foods is essential to calculate their chemical score, which is used to predict protein quality of foods and diets. Though amino acid composition of many foods is reasonably well established, better knowledge is needed on native foods consumed in different regions and countries. This paper presents the amino acid composition of different presentations of raw and processed foods produced and consumed in Mexico. The amino acid composition was determined using Beckman amino acid analyzers (models 116 and 6300). Tryptophan was determined using the Spies and Chambers method. Of the different foods analyzed, some comments are made on native or basic foods in Mexico: Spirulin, where lysine is the limiting amino acid, with a chemical score of 67%, is a good source of tryptophan (1.16g/16 gN); amaranth contains high levels of sulphur amino acids (4.09 to 5.34 g/16gN), with a protein content of 15 g/100g; and pulque, a Pre-Hispanic beverage that contains high levels of tryptophan (2.58 g/16 gN) and sulphur amino acids (2.72 g/16 gN). Finally, insects are good sources of sulphur amino acids and lysine.

Basic refractory and slag management for petcoke carbon feedstock in gasifiers

DOEpatents

Kwong, Kyei-Sing; Bennett, James P; Nakano, Jinichiro

2014-04-22

The disclosure provides methods of operating a slagging gasifier using a carbon feedstock having a relatively high V.sub.2O.sub.5 to SiO.sub.2 ratio, such as petcoke. The disclosure generates a combined chemical composition in the feed mixture having less than 25 wt. % SiO.sub.2, greater than 20 wt. % V.sub.2O.sub.5, and greater than 20 wt. % CaO. The method takes advantage of a novel recognition that increased levels of SiO.sub.2 tend to decrease dissolution of the V.sub.2O.sub.3 which forms under the reducing conditions of the gasifier, and utilizes the CaO additive to establish a chemical phase equilibria comprised of lower melting compounds. The method further provides for control based on the presence of Al.sub.2O.sub.3 and FeO, and provides for a total combined chemical composition of greater than about 5 wt. % MgO for use with refractory linings comprised of MgO based refractory brick.

Thermal and magnetic properties of chitosan-iron oxide nanoparticles.

PubMed

Soares, Paula I P; Machado, Diana; Laia, César; Pereira, Laura C J; Coutinho, Joana T; Ferreira, Isabel M M; Novo, Carlos M M; Borges, João Paulo

2016-09-20

Chitosan is a biopolymer widely used for biomedical applications such as drug delivery systems, wound healing, and tissue engineering. Chitosan can be used as coating for other types of materials such as iron oxide nanoparticles, improving its biocompatibility while extending its range of applications. In this work iron oxide nanoparticles (Fe3O4 NPs) produced by chemical precipitation and thermal decomposition and coated with chitosan with different molecular weights were studied. Basic characterization on bare and chitosan-Fe3O4 NPs was performed demonstrating that chitosan does not affect the crystallinity, chemical composition, and superparamagnetic properties of the Fe3O4 NPs, and also the incorporation of Fe3O4 NPs into chitosan nanoparticles increases the later hydrodynamic diameter without compromising its physical and chemical properties. The nano-composite was tested for magnetic hyperthermia by applying an alternating current magnetic field to the samples demonstrating that the heating ability of the Fe3O4 NPs was not significantly affected by chitosan. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of Cations on Corrosion of Inconel 625 in Molten Chloride Salts

NASA Astrophysics Data System (ADS)

Zhu, Ming; Ma, Hongfang; Wang, Mingjing; Wang, Zhihua; Sharif, Adel

2016-04-01

Hot corrosion of Inconel 625 in sodium chloride, potassium chloride, magnesium chloride, calcium chloride and their mixtures with different compositions is conducted at 900°C to investigate the effects of cations in chloride salts on corrosion behavior of the alloy. XRD, SEM/EDS were used to analyze the compositions, phases, and morphologies of the corrosion products. The results showed that Inconel 625 suffers more severe corrosion in alkaline earth metal chloride molten salts than alkaline metal chloride molten salts. For corrosion in mixture salts, the corrosion rate increased with increasing alkaline earth metal chloride salt content in the mixture. Cations in the chloride molten salts mainly affect the thermal and chemical properties of the salts such as vapor pressure and hydroscopicities, which can affect the basicity of the molten salt. Corrosion of Inconel 625 in alkaline earth metal chloride salts is accelerated with increasing basicity.

Les dykes basiques du massif ancien de l'Ourika (Atlas de Marrakech, Maroc): géochimie et significationThe basic dykes of the Ourika old massif (High Atlas of Marrakech): Geochemistry and significance

NASA Astrophysics Data System (ADS)

Barakat, Ahmed; Marignac, Christian; Bouabdelli, Mohamed

The Precambrian massif of Ourika is crosscut by two systems of basic dykes, striking N40°E and N90-120°E. Using incompatible trace elements, the two systems form two distinct chemical groups, displaying a continental tholeiitic affinity. The composition variations between the two defined groups can be due to heterogeneities of mantle sources and to contamination, during the magma ascent, by the continental crust. The emplacement of these basic dykes, before the late-PIII formations, can be related to the Neoproterozoic distension generalised to the Anti-Atlas chain. To cite this article: A. Barakat et al., C. R. Geoscience 334 (2002) 827-833.

Modification of the Surface Topography and Composition of Ultrafine and Coarse Grained Titanium by Chemical Etching.

PubMed

Nazarov, Denis V; Zemtsova, Elena G; Solokhin, Alexandr Yu; Valiev, Ruslan Z; Smirnov, Vladimir M

2017-01-13

In this study, we present the detailed investigation of the influence of the etching medium (acidic or basic Piranha solutions) and the etching time on the morphology and surface relief of ultrafine grained (UFG) and coarse grained (CG) titanium. The surface relief and morphology have been studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), and the spectral ellipsometry. The composition of the samples has been determined by X-ray fluorescence analysis (XRF) and X-ray Photoelectron Spectroscopy (XPS). Significant difference in the etching behavior of UFG and CG titanium has been found. UFG titanium exhibits higher etching activity independently of the etching medium. Formed structures possess higher homogeneity. The variation of the etching medium and time leads to micro-, nano-, or hierarchical micro/nanostructures on the surface. Significant difference has been found between surface composition for UFG titanium etched in basic and acidic Piranha solution. Based on the experimental data, the possible reasons and mechanisms are considered for the formation of nano- and microstructures. The prospects of etched UFG titanium as the material for implants are discussed.

Features of Different Inorganic Scintillators Used in Neutron-Radiation Systems for Illegal Substance Detection

NASA Astrophysics Data System (ADS)

Batyaev, V. F.; Belichenko, S. G.; Bestaev, R. R.

2016-04-01

The work is devoted to a quantitative comparison of different inorganic scintillators to be used in neutron-radiation inspection systems. Such systems can be based on the tagged neutron (TN) method and have a significant potential in different applications such as detection of explosives, drugs, mines, identification of chemical warfare agents, assay of nuclear materials and human body composition [1]-[3]. The elemental composition of an inspected object is determined via spectrometry of gammas from the object bombarded by neutrons which are tagged by an alpha-detector built inside a neutron generator. This creates a task to find a quantitative indicator of the object identification quality (via elemental composition) as a function of basic parameters of the γ-detectors, such as their efficiency, energy and time resolutions, which in turn are generally defined by a scintillator of the detector. We have tried to solve the task for a set of four scintillators which are often used in the study of TN method, namely BGO, LaBr3, LYSO, NaI(Tl), whose basic parameters are well known [4]-[7].

Modification of the Surface Topography and Composition of Ultrafine and Coarse Grained Titanium by Chemical Etching

PubMed Central

Nazarov, Denis V.; Zemtsova, Elena G.; Solokhin, Alexandr Yu.; Valiev, Ruslan Z.; Smirnov, Vladimir M.

2017-01-01

In this study, we present the detailed investigation of the influence of the etching medium (acidic or basic Piranha solutions) and the etching time on the morphology and surface relief of ultrafine grained (UFG) and coarse grained (CG) titanium. The surface relief and morphology have been studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), and the spectral ellipsometry. The composition of the samples has been determined by X-ray fluorescence analysis (XRF) and X-ray Photoelectron Spectroscopy (XPS). Significant difference in the etching behavior of UFG and CG titanium has been found. UFG titanium exhibits higher etching activity independently of the etching medium. Formed structures possess higher homogeneity. The variation of the etching medium and time leads to micro-, nano-, or hierarchical micro/nanostructures on the surface. Significant difference has been found between surface composition for UFG titanium etched in basic and acidic Piranha solution. Based on the experimental data, the possible reasons and mechanisms are considered for the formation of nano- and microstructures. The prospects of etched UFG titanium as the material for implants are discussed. PMID:28336849

A concept for improved fire-safety through coated fillers

NASA Technical Reports Server (NTRS)

Ramohalli, K.

1977-01-01

A possible method is examined for obtaining a high value of thermal conductivity before ignition and a low value after ignition in standard composite materials. The idea is to coat fiberglass, alumina trihydrate, and similar fillers with specially selected chemicals prior to using polymer resins. The amount of the coat constitutes typically less than 5% of the material's total weight. The experimental results obtained are consistent with the basic concept.

Exoplanet atmospheres: a brand-new and rapidly expanding research field

NASA Astrophysics Data System (ADS)

López-Morales, M.

2011-11-01

The field of exoplanets is quickly expanding from just the detectionof new planets and the measurement of their most basic parameters,such as mass, radius and orbital configuration, to the firstmeasurements of their atmospheric characteristics, such astemperature, chemical composition, albedo, dynamics andstructure. Here I will overview some the main findings on exoplanetatmospheres until September 2010, first from space and just in thepast two years also from the ground.

On the Chemical Characterization of Organic Matter in Rain at Mexico City.

NASA Astrophysics Data System (ADS)

Montero-Martinez, G.; Andraca-Ayala, G. L.; Hernández-Nagay, D. P.; Mendoza-Trejo, A.; Rivera-Arellano, J.; Rosado-Abon, A.; Roy, P. D.

2016-12-01

The chemical composition of the aerosol plays a central role in atmospheric processes and has influence on the hydrological cycle. Clouds form through the nucleation of water vapor on certain atmospheric aerosol particles, called cloud condensation nuclei (CCN). Also, precipitating particles scavenge some other aerosol particles on their way to the surface. Atmospheric particles are a mixture of organic and inorganic materials, both soluble and insoluble in water. Aerosol chemical characterization indicates a larger variety of compounds in urban areas respect to other regions. Thus, chemical composition of rainwater may represent an important aspect for estimating atmospheric air pollution. It has been recognized that organic species present in aerosol particles are important in the formation of cloud droplets. Therefore, the information about the organic compounds in precipitation samples may be helpful to understand their effects on the formation of clouds and rain, as well as their sources. Organic acids are ubiquitous components of aerosols and have been identified in precipitation water. In this work, preliminary results of the content of soluble organic (neutral and acidic) matter in rainwater samples collected in Mexico City during 2015 will be presented. The organic compounds content was performed by using an ionic chromatographic methodology with gradient elution; so the total amount was evaluated as the sum of four fractions: neutral/basic, mono-, bi-, and poly-acid compounds. The outcomes suggest that most of the amount of organic substances soluble in water is contained by the neutral/basic and mono-acid fractions. Regarding the total amount of water soluble organic compounds, the rain samples collected in Mexico City are in agreement with some others reported for large urban areas.

On-line monitoring of oxygen as a method to qualify the oxygen consumption rate of wines.

PubMed

Nevares, Ignacio; Martínez-Martínez, Víctor; Martínez-Gil, Ana; Martín, Roberto; Laurie, V Felipe; Del Álamo-Sanza, María

2017-08-15

Measuring the oxygen content during winemaking and bottle storage has become increasingly popular due to its impact on the sensory quality and longevity of wines. Nevertheless, only a few attempts to describe the kinetics of oxygen consumption based on the chemical composition of wines have been published. Therefore, this study proposes firstly a new fitting approach describing oxygen consuming kinetics and secondly the use of an Artificial Neural Network approach to describe and compare the oxygen avidity of wines according to their basic chemical composition (i.e. the content of ethanol, titratable acidity, total sulfur dioxide, total phenolics, iron and copper). The results showed no significant differences in the oxygen consumption rate between white and red wines, and allowed the sorting of the wines studied according to their oxygen consumption rate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ultraviolet and thermally stable polymer compositions

NASA Technical Reports Server (NTRS)

Reinisch, R. F.; Gloria, H. R.; Goldsberry, R. E.; Adamson, M. J. (Inventor)

1976-01-01

A new class of polymers is provided, namely, poly (diarylsiloxy) arylazines. These novel polymers have a basic chemical composition which has the property of stabilizing the optical and physical properties of the polymer against the degradative effect of ultraviolet light and high temperatures. This stabilization occurs at wavelengths including those shorter than found on the surface of the earth and in the absence or presence of oxygen, making the polymers useful for high performance coating applications in extraterrestrial space as well as similar applications in terrestrial service. The invention also provides novel aromatic azines which are useful in the preparation of polymers such as those described.

Ultraviolet and thermally stable polymer compositions

NASA Technical Reports Server (NTRS)

Reinisch, R. F.; Gloria, H. R.; Goldsberry, R. E.; Adamson, M. J. (Inventor)

1974-01-01

A class of polymers is provided, namely, poly(diarylsiloxy) arylazines. These polymers have a basic chemical composition which has the property of stabilizing the optical and physical properties of the polymer against the degradative effect of ultraviolet light and high temperatures. This stabilization occurs at wavelengths including those shorter than found on the surface of the earth and in the absence or presence of oxygen, making the polymers of the present invention useful for high performance coating applications in extraterrestrial space as well as similar applications in terrestrial service. The invention also provides aromatic azines which are useful in the preparation of polymers such as those of the present invention.

Textural variability of ordinary chondrite chondrules: Implications of their formation

NASA Technical Reports Server (NTRS)

Zinovieva, N. G.; Mitreikina, O. B.; Granovsky, L. B.

1994-01-01

Scanning electron microscopy (SEM) and microprobe examination of the Raguli H3-4, Saratov L3, and Fucbin L5-6 ordinary chondrites and the analysis of preexisted data on other meteorites have shown that the variety of textural types of chondrules depends on the chemical composition of the chondrules. The comparison of bulk-rock chemistries of the chondrules by major components demonstrates that they apparently fall, like basic-ultrabasic rock, into groups of dunitic and pyroxenitic composition. This separation is further validated by the character of zoning in chondrules of the intermediate, peridotitic type. The effect is vividly demonstrated by the 'chondrule-in-chondrule' structure.

Computer Modeling of Basic Physico-Chemical Processes for DSEC Composites of System LaB6-MeB2(MeTi, Zr, Hf) at Macro-, Meso- and Microstructure Scales

DTIC Science & Technology

2010-07-15

operations of mathematical morphology applied for analysis of images are ways to extract information of image. The approach early developed [52] to use...1,2568 57 VB2 5,642; 5,804; 5,67; 5,784 0,5429 0,2338 0,04334 0,45837 CrB2 5,62; 5,779; 5,61; 5,783 0,53276 0,23482...maxT For VB2 - has min value if compare with other composite materials on the base of LaB6 and diborides of transitive metals [3], = Joule and

Characterization and utilization potential of basalt rock from East-Lampung district

NASA Astrophysics Data System (ADS)

Isnugroho, K.; Hendronursito, Y.; Birawidha, D. C.

2018-01-01

The aim of this research was to study the petrography and chemical properties of basalt rock from East Lampung district, Lampung province. Petrography analysis was performed using a polarization microscope, and analysis of chemical composition using X-RF method. From the analysis of basalt rock samples, the mineral composition consists of pyroxene, plagioclase, olivine, and opaque minerals. Basic mass of basalt rock samples is, composed of plagioclase and pyroxene with subhedral-anhedral shape, forming intergranular texture, and uniform distribution. Mineral plagioclase is colorless and blade shape, transformed into opaque minerals with a size of <0.2 mm, whereas pyroxene present among the blades of plagioclase, with a greenish tint looked and a size of <0.006 mm. Mineral opaque has a rectangular shape to irregular, with a size of <0.16 mm. The chemical composition of basalt rock samples, consisting of 37.76-59.64 SiO2; 10.10-20.93 Fe2O3; 11.77-14.32 Al2O3; 5.57-14.75 CaO; 5.37-9.15 MgO; 1.40-3.34 Na2O. From the calculation, obtained the value of acidity ratio (Ma) = 3.81. With these values, indicate that the basalt rock from East Lampung district has the potential to be utilized as stone wool fiber.

Conductive polymeric compositions for lithium batteries

DOEpatents

Angell, Charles A [Mesa, AZ; Xu, Wu [Tempe, AZ

2009-03-17

Novel chain polymers comprising weakly basic anionic moieties chemically bound into a polyether backbone at controllable anionic separations are presented. Preferred polymers comprise orthoborate anions capped with dibasic acid residues, preferably oxalato or malonato acid residues. The conductivity of these polymers is found to be high relative to that of most conventional salt-in-polymer electrolytes. The conductivity at high temperatures and wide electrochemical window make these materials especially suitable as electrolytes for rechargeable lithium batteries.

Polymer ceramic composite that follows the rules of bone growth

NASA Astrophysics Data System (ADS)

Dry, Carolyn M.; Warner, Carrie

1998-07-01

Research at the University of Illinois School of Architecture Material's Lab is being done on a biomimetic building material with the unique properties of bone. This polymer/ceramic composite will mimic bone by controlling the (1) the structure and form of the material, (2) chemical makeup and sequencing of fabrication, (3) ability to adapt to environmental changes during fabrication, and (4) ability to later adapt and repair itself. Bones and shells obtain their great toughness and strength as a result of careful control of these four factors. The organic fibers are made first and the matrix grown around them as opposed to conventional ceramics in which any fibers are added to the matrix. Constituents are also placed in the material which allow it to later adapt to outside changes. The rules under which bone material naturally forms and adapts, albeit at a macroscale, are followed. Our efforts have concentrated on the chemical makeup, and basic sequencing of fabrication. Our research sought to match the intimate connection between material phases of bone by developing the chemical makeup.

Characterization of composite materials based on cement-ceramic powder blended binder

NASA Astrophysics Data System (ADS)

Kulovaná, Tereza; Pavlík, Zbyšek

2016-06-01

Characterization of newly developed composite mortars with incorporated ceramic powder coming from precise brick cutting as partial Portland cement replacement up to 40 mass% is presented in the paper. Fine ceramic powder belongs to the pozzolanic materials. Utilization of pozzolanic materials is accompanied by lower request on energy needed for Portland clinker production which generally results in lower production costs of blended binder and lower CO2 emission. In this paper, the ceramic powder is used in cement based mortar composition in amount of 8, 16, 24, 32, and 40 mass% of cement. Chemical composition of ceramic powder is analyzed by X-Ray Fluorescence and X-Ray Diffraction. The particle size distribution of ceramics is accessed on laser diffraction principle. For 28 days cured mortar samples, basic physical and mechanical properties are experimentally determined. The obtained results demonstrate that ceramic powder has potential to replace a part of Portland cement in composition of cement based composites and to reduce negative environmental impact of their production.

Characterization of composite materials based on cement-ceramic powder blended binder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kulovaná, Tereza; Pavlík, Zbyšek

Characterization of newly developed composite mortars with incorporated ceramic powder coming from precise brick cutting as partial Portland cement replacement up to 40 mass% is presented in the paper. Fine ceramic powder belongs to the pozzolanic materials. Utilization of pozzolanic materials is accompanied by lower request on energy needed for Portland clinker production which generally results in lower production costs of blended binder and lower CO{sub 2} emission. In this paper, the ceramic powder is used in cement based mortar composition in amount of 8, 16, 24, 32, and 40 mass% of cement. Chemical composition of ceramic powder is analyzedmore » by X-Ray Fluorescence and X-Ray Diffraction. The particle size distribution of ceramics is accessed on laser diffraction principle. For 28 days cured mortar samples, basic physical and mechanical properties are experimentally determined. The obtained results demonstrate that ceramic powder has potential to replace a part of Portland cement in composition of cement based composites and to reduce negative environmental impact of their production.« less

Formulations for Stronger Solid Oxide Fuel-Cell Electrolytes

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.; Goldsby, John C.; Choi, Sung R.

2004-01-01

Tests have shown that modification of chemical compositions can increase the strengths and fracture toughnesses of solid oxide fuel-cell (SOFC) electrolytes. Heretofore, these solid electrolytes have been made of yttria-stabilized zirconia, which is highly conductive for oxygen ions at high temperatures, as needed for operation of fuel cells. Unfortunately yttria-stabilized zirconia has a high coefficient of thermal expansion, low resistance to thermal shock, low fracture toughness, and low mechanical strength. The lack of strength and toughness are especially problematic for fabrication of thin SOFC electrolyte membranes needed for contemplated aeronautical, automotive, and stationary power-generation applications. The modifications of chemical composition that lead to increased strength and fracture toughness consist in addition of alumina to the basic yttria-stabilized zirconia formulations. Techniques for processing of yttria-stabilized zirconia/alumina composites containing as much as 30 mole percent of alumina have been developed. The composite panels fabricated by these techniques have been found to be dense and free of cracks. The only material phases detected in these composites has been cubic zirconia and a alumina: this finding signifies that no undesired chemical reactions between the constituents occurred during processing at elevated temperatures. The flexural strengths and fracture toughnesses of the various zirconia-alumina composites were measured in air at room temperature as well as at a temperature of 1,000 C (a typical SOFC operating temperature). The measurements showed that both flexural strength and fracture toughness increased with increasing alumina content at both temperatures. In addition, the modulus of elasticity and the thermal conductivity were found to increase and the density to decrease with increasing alumina content. The oxygen-ion conductivity at 1,000 C was found to be unchanged by the addition of alumina.

Examination of lignocellulosic fibers for chemical, thermal, and separations properties: Addressing thermo-chemical stability issues

NASA Astrophysics Data System (ADS)

Johnson, Carter David

Natural fiber-plastic composites incorporate thermoplastic resins with fibrous plant-based materials, sometimes referred to as biomass. Pine wood mill waste has been the traditional source of natural fibrous feedstock. In anticipation of a waste wood shortage other fibrous biomass materials are being investigated as potential supplements or replacements. Perennial grasses, agricultural wastes, and woody biomass are among the potential source materials. As these feedstocks share the basic chemical building blocks; cellulose, hemicellulose, and lignin, they are collectively called lignocellulosics. Initial investigation of a number of lignocellulosic materials, applied to fiber-plastic composite processing and material testing, resulted in varied results, particularly response to processing conditions. Less thermally stable lignocellulosic filler materials were physically changed in observable ways: darkened color and odor. The effect of biomass materials' chemical composition on thermal stability was investigated an experiment involving determination of the chemical composition of seven lignocellulosics: corn hull, corn stover, fescue, pine, soy hull, soy stover, and switchgrass. These materials were also evaluated for thermal stability by thermogravimetric analysis. The results of these determinations indicated that both chemical composition and pretreatment of lignocellulosic materials can have an effect on their thermal stability. A second study was performed to investigate what effect different pretreatment systems have on hybrid poplar, pine, and switchgrass. These materials were treated with hot water, ethanol, and a 2:1 benzene/ethanol mixture for extraction times of: 1, 3, 6, 12, and 24 hours. This factorial experiment demonstrated that both extraction time and medium have an effect on the weight percent of extractives removed from all three material types. The extracted materials generated in the above study were then subjected to an evaluation of thermal stability by thermogravimetric analysis in a subsequent experiment. Overlay plots, combining individual weight loss curves, demonstrate that the experimental factors, solvent system and extraction time, produce effects on the thermal stability of the treated biomass samples. These data also indicated that the individual lignocellulosic materials had unique responses to the type of solvent used for pretreatment. Increasing extraction time had either no correlation with or a positive effect on thermal stability of the biomass samples.

Statistical research using the multiple regression analysis in areas of the cast hipereutectoid steel rolls manufacturing

NASA Astrophysics Data System (ADS)

Kiss, I.; Alexa, V.; Serban, S.; Rackov, M.; Čavić, M.

2018-01-01

The cast hipereutectoid steel (usually named Adamite) is a roll manufacturing destined material, having mechanical, chemical properties and Carbon [C] content of which stands between steelandiron, along-withitsalloyelements such as Nickel [Ni], Chrome [Cr], Molybdenum [Mo] and/or other alloy elements. Adamite Rolls are basically alloy steel rolls (a kind of high carbon steel) having hardness ranging from 40 to 55 degrees Shore C, with Carbon [C] percentage ranging from 1.35% until to 2% (usually between 1.2˜2.3%), the extra Carbon [C] and the special alloying element giving an extra wear resistance and strength. First of all the Adamite roll’s prominent feature is the small variation in hardness of the working surface, and has a good abrasion resistance and bite performance. This paper reviews key aspects of roll material properties and presents an analysis of the influences of chemical composition upon the mechanical properties (hardness) of the cast hipereutectoid steel rolls (Adamite). Using the multiple regression analysis (the double and triple regression equations), some mathematical correlations between the cast hipereutectoid steel rolls’ chemical composition and the obtained hardness are presented. In this work several results and evidence obtained by actual experiments are presented. Thus, several variation boundaries for the chemical composition of cast hipereutectoid steel rolls, in view the obtaining the proper values of the hardness, are revealed. For the multiple regression equations, correlation coefficients and graphical representations the software Matlab was used.

MRI of chemical reactions and processes.

PubMed

Britton, Melanie M

2017-08-01

As magnetic resonance imaging (MRI) can spatially resolve a wealth of molecular information available from nuclear magnetic resonance (NMR), it is able to non-invasively visualise the composition, properties and reactions of a broad range of spatially-heterogeneous molecular systems. Hence, MRI is increasingly finding applications in the study of chemical reactions and processes in a diverse range of environments and technologies. This article will explain the basic principles of MRI and how it can be used to visualise chemical composition and molecular properties, providing an overview of the variety of information available. Examples are drawn from the disciplines of chemistry, chemical engineering, environmental science, physics, electrochemistry and materials science. The review introduces a range of techniques used to produce image contrast, along with the chemical and molecular insight accessible through them. Methods for mapping the distribution of chemical species, using chemical shift imaging or spatially-resolved spectroscopy, are reviewed, as well as methods for visualising physical state, temperature, current density, flow velocities and molecular diffusion. Strategies for imaging materials with low signal intensity, such as those containing gases or low sensitivity nuclei, using compressed sensing, para-hydrogen or polarisation transfer, are discussed. Systems are presented which encapsulate the diversity of chemical and physical parameters observable by MRI, including one- and two-phase flow in porous media, chemical pattern formation, phase transformations and hydrodynamic (fingering) instabilities. Lastly, the emerging area of electrochemical MRI is discussed, with studies presented on the visualisation of electrochemical deposition and dissolution processes during corrosion and the operation of batteries, supercapacitors and fuel cells. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

The volatile composition of comets

NASA Technical Reports Server (NTRS)

Weaver, H. A.

1988-01-01

Comets may be our best probes of the physical and chemical conditions in the outer regions of the solar nebula during that crucial period when the planets formed. The volatile composition of cometary nuclei can be used to decide whether comets are the product of a condensation sequence similar to that invoked to explain the compositions of the planets and asteroids, or if comets are simply agglomerations of interstellar grains which have been insignificantly modified by the events that shaped the other bodies in the solar system. Although cometary nuclei are not generally accessible to observation, observations of cometary comae can illuminate at least some of the mysteries of the nuclei provided one has a detailed knowledge of the excitation conditions in the coma and also has access to basic atomic and molecular data on the many species present in comets. Examined here is the status of our knowledge of the volatile composition of cometary nuclei and how these data are obtained.

Evolution of the atomic order and valence state of rare-earth atoms and uranium in a new carbon-metal composite—diphthalocyanine pyrolysate C64H32N16 Me ( Me = Y, La, Ce, Eu, and U)

NASA Astrophysics Data System (ADS)

Sovestnov, A. E.; Kapustin, V. K.; Tikhonov, V. I.; Fomin, E. V.; Chernenkov, Yu. P.

2014-08-01

The structure of a metal-carbon composite formed by the pyrolysis of diphthalocyanine of some rare-earth elements (Y, La, Ce, Eu) and uranium in the temperature range T ann = 800-1700°C has been investigated for the first time by the methods of X-ray diffraction analysis and X-ray line shift. It has been shown that, in the general case, the studied pyrolysates consist of three phases. One phase corresponds to the structure of graphite. The second phase corresponds to nitrides, carbides, and oxides of basic metal elements with a crystallite size ranging from 5 to 100 nm. The third phase is amorphous or consisting of crystallites with a size of ˜1 nm. It has been found that all the basic elements (Y, La, Ce, Eu, U) and incorporated iodine atoms in the third phase are in a chemically bound state. The previously unobserved electronic configurations have been revealed for europium. The possibility of including not only atoms of elements forming diphthalocyanine but also other elements (for example, iodine) in the composite structure is of interest, in particular, for the creation of a thermally, chemically, and radiation resistant metal-carbon matrix for the radioactive waste storage.

Glass Formation, Chemical Properties and Surface Analysis of Cu-Based Bulk Metallic Glasses

PubMed Central

Qin, Chunling; Zhao, Weimin; Inoue, Akihisa

2011-01-01

This paper reviews the influence of alloying elements Mo, Nb, Ta and Ni on glass formation and corrosion resistance of Cu-based bulk metallic glasses (BMGs). In order to obtain basic knowledge for application to the industry, corrosion resistance of the Cu–Hf–Ti–(Mo, Nb, Ta, Ni) and Cu–Zr–Ag–Al–(Nb) bulk glassy alloy systems in various solutions are reported in this work. Moreover, X-ray photoelectron spectroscopy (XPS) analysis is performed to clarify the surface-related chemical characteristics of the alloy before and after immersion in the solutions; this has lead to a better understanding of the correlation between the surface composition and the corrosion resistance. PMID:21731441

Hanford Soil Inventory Model (SIM-v2) Calculated Radionuclide Inventory of Direct Liquid Discharges to Soil in the Hanford Site's 200 Areas.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, William E.; Zaher, U.; Agnew, S.

The Hanford soil inventory model (SIM) provides the basic radionuclide and chemical soil inventories from historical liquid discharges to about 400 sites at the Hanford Site. Although liquid discharge inventory for chemicals is part of the SIM implementation, only radionuclide inventory is discussed here since the focus of this ECF is on providing radionuclides inputs for the composite analysis (CA) per DOE Order 435.1, Radioactive Waste Management, requirements. Furthermore, discharged inventories are only estimated for the soluble portions of the liquid discharges to waste sites/waste management areas located on the 200 Area of the Hanford Site (Central Plateau).

[Advances in research of chemical constituents and pharmacological activities of common used spices].

PubMed

Sun, Chao-nan; Zhu, Yuan; Xu, Xi-ming; Yu, Jiang-nan

2014-11-01

Spices have enjoyed a long history and a worldwide application. Of particular interest is the pharmaceutical value of spices in addition to its basic seasoning function in cooking. Concretely, equipped with complex chemical compositions, spices are of significant importance in pharmacologic actions, like antioxidant, antibacterial, antitumor, as well as therapeutical effects in gastrointestinal disorders and cardiovascular disease. Although increasing evidences in support of its distinct role in the medical field has recently reported, little information is available for substantive, thorough and sophisticated researches on its chemical constituents and pharmacological activities, especially mechanism of these actions. Therefore, in popular wave of studies directed at a single spice, this review presents systematic studies on the chemical constituents and pharmacological activities associated with common used spices, together with current typical individual studies on functional mechanism, in order to pave the way for the exploitation and development of new medicines derived from the chemical compounds of spice (such as, piperine, curcumin, geniposide, cinnamaldehyde, cinnamic acid, linalool, estragole, perillaldehyde, syringic acid, crocin).

Exploring the Effects of Geographical Origin on the Chemical Composition and Quality Grading of Vitis vinifera L. cv. Chardonnay Grapes.

PubMed

Gambetta, Joanna M; Cozzolino, Daniel; Bastian, Susan E P; Jeffery, David W

2017-01-31

The relationship between berry chemical composition, region of origin and quality grade was investigated for Chardonnay grapes sourced from vineyards located in seven South Australian Geographical Indications (GI). Measurements of basic chemical parameters, amino acids, elements, and free and bound volatiles were conducted for grapes collected during 2015 and 2016. Multiple factor analysis (MFA) was used to determine the sets of data that best discriminated each GI and quality grade. Important components for the discrimination of grapes based on GI were 2-phenylethanol, benzyl alcohol and C6 compounds, as well as Cu, Zn, and Mg, titratable acidity (TA), total soluble solids (TSS), and pH. Discriminant analysis (DA) based on MFA results correctly classified 100% of the samples into GI in 2015 and 2016. Classification according to grade was achieved based on the results for elements such as Cu, Na, Fe, volatiles including C6 and aryl alcohols, hydrolytically-released volatiles such as (Z)-linalool oxide and vitispirane, pH, TSS, alanine and proline. Correct classification through DA according to grade was 100% for both vintages. Significant correlations were observed between climate, GI, grade, and berry composition. Climate influenced the synthesis of free and bound volatiles as well as amino acids, sugars, and acids, as a result of higher temperatures and precipitation.

Petrographic, mineralogical, and chemical characterization of certain Alaskan coals and washability products. Final report, July 11, 1978-October 11, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rao, P.D.; Wolff, E.N.

1981-05-01

Petrological, mineralogical and chemical characterization provides basic information needed for proper utilization of coals. Since many of these coals are likely to be beneficiated to reduce ash, the influence of coal washing on the characteristics of the washed product is important. Twenty samples of Alaskan coal seams were used for this study. The coals studied ranged in rank from lignite to high volatile A bituminous with vitrinite/ulminite reflectance ranging from 0.25 to 1.04. Fifteen raw coals were characterized for proximate and ultimate analysis reflectance rank, petrology, composition of mineral matter, major oxides and trace elements in coal ash. Washability productsmore » of three coals from Nenana, Beluga and Matanuska coal fields were used for characterization of petrology, mineral matter and ash composition. Petrological analysis of raw coals and float-sink products showed that humodetrinite was highest in top seam in a stratigraphic sequence« less

Automatic control of the effluent turbidity from a chemically enhanced primary treatment with microsieving.

PubMed

Väänänen, J; Memet, S; Günther, T; Lilja, M; Cimbritz, M; la Cour Jansen, J

2017-10-01

For chemically enhanced primary treatment (CEPT) with microsieving, a feedback proportional integral controller combined with a feedforward compensator was used in large pilot scale to control effluent water turbidity to desired set points. The effluent water turbidity from the microsieve was maintained at various set points in the range 12-80 NTU basically independent for a number of studied variations in influent flow rate and influent wastewater compositions. Effluent turbidity was highly correlated with effluent chemical oxygen demand (COD). Thus, for CEPT based on microsieving, controlling the removal of COD was possible. Thereby incoming carbon can be optimally distributed between biological nitrogen removal and anaerobic digestion for biogas production. The presented method is based on common automation and control strategies; therefore fine tuning and optimization for specific requirements are simplified compared to model-based dosing control.

Cellulose fibers obtained by organosolv process from date palm rachis (Phoenix dactylifera L.)

NASA Astrophysics Data System (ADS)

Ammar, H.; Abid, M.; Abid, S.

2012-02-01

In this preliminary study, the chemical composition of Tunisian DPR was established and discussed. The main characteristic of this agri-residue was its high lignin content in comparison with that of alfa plant. CIMV process was used to selectively separate cellulose fibres, hemicelluloses and lignin at atmospheric pressure. The obtained unbleached pulp was analysed in accordance with Kappa index and degree of polymerisation and then bleached by treating successively with peroxyacids and hydrogen peroxide in basic media.

Durability of cement and geopolimer composites

NASA Astrophysics Data System (ADS)

Błaszczyński, T.; Król, M.

2017-10-01

Concrete structures are constantly moving in the direction of improving the durability. This main feature depends on many factors, which are the composition of concrete mix, the usage of additives and admixtures and the place, where material will work and carry the load. The introduction of new geopolymer binders for geopolymer structures adds a new aspect that is type of used activator. This substance with strongly alkaline reaction is divided because of the physical state, the alkaline degree and above all the chemical composition. Taking into account, that at present the geopolymer binders are made essentially from waste materials or by products from the combustion of coal or iron ore smelting, unambiguous determination of the effect of the activator on the properties of the geopolymer material requires a number of trials, researches and observation. This paper shows the influence of the most alkaline activators on the basic parameters of the durability of geopolymer binders. In this study there were used a highly alkaline hydroxides, water glasses and granules, which are waste materials in a variety of processes taking place in a chemical plants. As the substrate of geopolymer binders there were used fly ash which came from coal and high calcium ash from the burning of lignite.

The metamorphic basement of the southern Sierra de Aconquija, Eastern Sierras Pampeanas: Provenance and tectonic setting of a Neoproterozoic back-arc basin

NASA Astrophysics Data System (ADS)

Cisterna, Clara Eugenia; Altenberger, Uwe; Mon, Ricardo; Günter, Christina; Gutiérrez, Antonio

2018-03-01

The Eastern Sierras Pampeanas are mainly composed of Neoproterozoic-early Palaeozoic metamorphic complexes whose protoliths were sedimentary sequences deposited along the western margin of Gondwana. South of the Sierra de Aconquija, Eastern Sierras Pampeanas, a voluminous metamorphic complex crops out. It is mainly composed of schists, gneisses, marbles, calk-silicate schists, thin layers of amphibolites intercalated with the marbles and granitic veins. The new data correlate the Sierra de Aconquija with others metamorphic units that crop out to the south, at the middle portion of the Sierra de Ancasti. Bulk rock composition reflects originally shales, iron rich shales, wackes, minor litharenites and impure limestones as its protoliths. Moreover, comparisons with the northern Sierra de Aconquija and from La Majada (Sierra de Ancasti) show similar composition. Amphibolites have a basaltic precursor, like those from the La Majada (Sierra de Ancasti) ones. The analyzed metamorphic sequence reflects low to moderate weathering conditions in the sediments source environment and their chemical composition would be mainly controlled by the tectonic setting of the sedimentary basin rather than by the secondary sorting and reworking of older deposits. The sediments composition reveal relatively low maturity, nevertheless the Fe - shale and the litharenite show a tendency of minor maturity among them. The source is related to an acid one for the litharenite protolith and a more basic to intermediate for the other rocks, suggesting a main derivation from intermediate to felsic orogen. The source of the Fe-shales may be related to and admixture of the sediments with basic components. Overall the composition point to an upper continental crust as the dominant sediment source for most of the metasedimentary rocks. The protolith of the amphibolites have basic precursors, related to an evolving back-arc basin. The chemical data in combination with the specific sediment association (wackes, shales, Fe-shales and minor litharenites) are characteristic for turbidity currents deposits along tectonically active region. They are also commonly associated with calcareous clays (marbles), commonly observed in the evolution of basins with slope and shelf derived carbonate turbidites. The amphibolites members are probably derived from lava-flows synchronous with the sedimentation during the basin evolution. The basin was controlled by a continental island arc possible evolving to a back-arc setting, as indicated for the mixed nature of the inferred source. The metasedimentary sequence from the Cuesta de La Chilca have petrographic, structural and strong chemical similarities, building a north-south striking belt from the north of the Sierra de Aconquija and to the south along the Sierra de Ancasti (La Majada area). The observed similarities allow to present this portion of the Eastern Sierras Pampeanas as a crustal block that records the sedimentary sequences developed along the geodynamic context of the southwestern margin of Gondwana during the Neoproterozoic and Early Palaeozoic.

Cortlandtitic enclaves associated with calc-alkaline granites from Tapia-Asturias (Hercynian Belt, northwestern Spain)

NASA Astrophysics Data System (ADS)

Galán, G.; Suárez, O.

1989-10-01

Petrographic and mineralogical characteristics of amphibole-olivine- and pyroxene-bearing ultramafic rocks from Asturias (NW Spain) are dealt with in this paper. These rocks are of cortlandtitic type and occur as small rare enclaves in basic rocks related to Hercynian calc-alkaline, post-tectonic epizonal granites, in the northwest of the Iberian Peninsula. These particular ultramafic enclaves are characterized by poikilitic cumulate microtexture. Olivine (Fo 77-81), spinel, from chromite to pleonaste composition, enstatite, subordinated diopside and sulphides are included in large brown calcic amphibole crystals displaying an irregular zonation. Phlogopite and plagioclase are also found, in a much lower proportion, between the large amphibole crystals. Mineral assemblage and chemical composition of minerals indicate formation conditions of 1150°C, 7-8 kbar of Ptotal and PH 2O < Ptotal. These rocks could represent the earlier products of fractional crystallization from a hydrated high-alumina basalt involved in the genesis of the calc-alkaline granites. This basic magma would start crystallizing at a relatively deep level, carrying up the first products of its crystallization during its ascent.

The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

NASA Astrophysics Data System (ADS)

Temnikova, E. Yu; Bogomolov, A. R.; Lapin, A. A.

2017-11-01

In this paper, we propose to use the slag and ash material of thermal power plants (TPP) operating on pulverized coal fuel. The elemental and chemical composition of fly ash of five Kuzbass thermal power plants differs insignificantly from the composition of the mineral part of coking coal because coke production uses a charge, whose composition defines the main task: obtaining coke with the required parameters for production of iron and steel. These indicators are as follows: CRI reactivity and strength of the coke residue after reaction with CO2 - CSR. The chemical composition of fly ash of thermal power plants and microsilica with bulk density of 0.3-0.6 t/m3 generated at production of ferroalloys was compared. Fly ash and microsilica are the valuable raw material for production of mineral binder in manufacturing coke breeze briquettes (fraction of 2-10 mm) and dust (0-200 μm), generated in large quantities during coking (up to 40wt%). It is shown that this binder is necessary for production of smokeless briquettes with low reactivity, high strength and cost, demanded for production of cupola iron and melting the silicate materials, basaltic rocks in low-shaft furnaces. It is determined that microsilica contains up to 90% of silicon oxide, and fly ash contains up to 60% of silicon oxide and aluminum oxide of up to 20%. On average, the rest of fly ash composition consists of basic oxides. According to calculation by the VUKHIN formula, the basicity index of briquette changes significantly, when fly ash is introduced into briquette raw material component as a binder. The technology of coke briquette production on the basis of the non-magnetic fraction of TPP fly ash in the ratio from 3.5:1 to 4.5:1 (coke breeze : coke dust) with the addition of the binder component to 10% is proposed. The produced briquettes meet the requirements by CRI and require further study on CSR requirements.

Effect of Physicochemical Properties of Slag and Flux on the Removal Rate of Oxide Inclusion from Molten Steel

NASA Astrophysics Data System (ADS)

Park, Jun Seok; Park, Joo Hyun

2016-12-01

The slag-metal reaction experiments were carried out using a high-frequency induction furnace to confirm the effect of slag composition on the removal rate of inclusions in molten steel through the CaO-based slags. The apparent rate constant of oxygen removal ( k O) was obtained as a function of slag composition. It increased with increasing basicity, and the content of MgO and CaF2, whereas it decreased by increasing the content of Al2O3 in the slag. The removal rate of inclusions was strongly affected not only by the driving force of the chemical dissolution but also by the viscosity of the slags and fluxes.

Synthesis, structural properties and thermal stability of Mn-doped hydroxyapatite

NASA Astrophysics Data System (ADS)

Paluszkiewicz, Czesława; Ślósarczyk, Anna; Pijocha, Dawid; Sitarz, Maciej; Bućko, Mirosław; Zima, Aneta; Chróścicka, Anna; Lewandowska-Szumieł, Małgorzata

2010-07-01

Hydroxyapatite (HA) - Ca 10(PO 4) 6(OH) 2 is a basic inorganic model component of hard biological tissues, such as bones and teeth. The significant property of HA is its ability to exchange Ca 2+ ions, which influences crystallinity, physico-chemical and biological properties of modified hydroxyapatite materials. In this work, FTIR, Raman spectroscopy, XRD, SEM and EDS techniques were used to determine thermal stability, chemical and phase composition of Mn containing hydroxyapatite (MnHA). Described methods confirmed thermal decomposition and phase transformation of MnHA to αTCP, βTCP and formation of Mn 3O 4 depending on sintering temperature and manganese content. In vitro biological evaluation of Mn-modified HA ceramics was also performed using human osteoblast cells.

Facile fabrication of corrosion-resistant superhydrophobic and superoleophilic surfaces with MnWO(4):Dy(3+) microbouquets.

PubMed

Li, Taohai; Li, Quanguo; Yan, Jing; Li, Feng

2014-04-21

Superhydrophobic and superoleophilic MnWO4:Dy(3+) microbouquets were successfully fabricated via a facile hydrothermal process. The surface morphologies and chemical composition were investigated by scanning electron microscopy (SEM) and X-ray powder diffraction (XRD). The wettability of the as-synthesized MnWO4:Dy(3+) microbouquet film was studied by measuring the water contact angle (CA). A static CA for water of 165° and a very low sliding angle (SA) were observed, which were closely related to both the MnWO4:Dy(3+) microbouquet structure and chemical modification. Furthermore, the as-prepared MnWO4:Dy(3+) surface showed superhydrophobicity for some corrosive liquids such as aqueous basic and salt solutions.

[Monitoring of the chemical composition of snow cover pollution in the Moscow region].

PubMed

Ermakov, A A; Karpova, E A; Malysheva, A G; Mikhaylova, R I; Ryzhova, I N

2014-01-01

Monitoring of snow cover pollution as an indicator of ambient air pollution in 20 districts in the Moscow region during 2009-2013 was performed. The identification with a quantitative assessment of a wide array of organic compounds and the control of the main physical and chemical and inorganic indices of snow water pollution were carried out. More than 60 organic substances for most of which there are no the hygienic standards were established. The assessment of pollution levels of basic inorganic indices was given by means of the comparing them with the average values in the snow cover in the European territory of Russia and natural content in areas not been exposed to human impact.

The Behavior of Translucent Composite Laminates under Highly Energetic Laser Irradiations

NASA Astrophysics Data System (ADS)

Allheily, Vadim; Merlat, Lionel; Lacroix, Fabrice; Eichhorn, Alfred; L'Hostis, Gildas

With the emergence of composite materials in the last decades, the interaction between light and diffusive materials has become a challenging topic in many key manufacturing areas (laser welding, laser surface treatment, engraving, etc.). In this paper, the behavior of laminated glass fiber-reinforced plastic composites (GFRP) under 1.07 μm-wavelength irradiations is investigated. Optical parameters are first assessed to build up a basic analytical interaction model involving internal refraction and reflection. The scattering effect due to the presence of oriented glass fibers is also a topic of interest. A thermodynamic analysis is then carried out from the induced volume heat source until the degradation temperature of the material is reached out. The study finally results in a one-dimensional model describing the optical and thermo-dynamical behavior of GFRP under high-power laser irradiations up to ignition of the chemical degradation phenomena.

A general approach to DNA-programmable atom equivalents.

PubMed

Zhang, Chuan; Macfarlane, Robert J; Young, Kaylie L; Choi, Chung Hang J; Hao, Liangliang; Auyeung, Evelyn; Liu, Guoliang; Zhou, Xiaozhu; Mirkin, Chad A

2013-08-01

Nanoparticles can be combined with nucleic acids to programme the formation of three-dimensional colloidal crystals where the particles' size, shape, composition and position can be independently controlled. However, the diversity of the types of material that can be used is limited by the lack of a general method for preparing the basic DNA-functionalized building blocks needed to bond nanoparticles of different chemical compositions into lattices in a controllable manner. Here we show that by coating nanoparticles protected with aliphatic ligands with an azide-bearing amphiphilic polymer, followed by the coupling of DNA to the polymer using strain-promoted azide-alkyne cycloaddition (also known as copper-free azide-alkyne click chemistry), nanoparticles bearing a high-density shell of nucleic acids can be created regardless of nanoparticle composition. This method provides a route to a virtually endless class of programmable atom equivalents for DNA-based colloidal crystallization.

An intermediate level of abstraction for computational systems chemistry.

PubMed

Andersen, Jakob L; Flamm, Christoph; Merkle, Daniel; Stadler, Peter F

2017-12-28

Computational techniques are required for narrowing down the vast space of possibilities to plausible prebiotic scenarios, because precise information on the molecular composition, the dominant reaction chemistry and the conditions for that era are scarce. The exploration of large chemical reaction networks is a central aspect in this endeavour. While quantum chemical methods can accurately predict the structures and reactivities of small molecules, they are not efficient enough to cope with large-scale reaction systems. The formalization of chemical reactions as graph grammars provides a generative system, well grounded in category theory, at the right level of abstraction for the analysis of large and complex reaction networks. An extension of the basic formalism into the realm of integer hyperflows allows for the identification of complex reaction patterns, such as autocatalysis, in large reaction networks using optimization techniques.This article is part of the themed issue 'Reconceptualizing the origins of life'. © 2017 The Author(s).

Cuticular Lipids as a Cross-Talk among Ants, Plants and Butterflies

PubMed Central

Barbero, Francesca

2016-01-01

Even though insects and plants are distantly related organisms, they developed an integument which is functionally and structurally similar. Besides functioning as a physical barrier to cope with abiotic and biotic stress, this interface, called cuticle, is also a source of chemical signaling. Crucial compounds with this respect are surface lipids and especially cuticular hydrocarbons (CHCs). This review is focused on the role of CHCs in fostering multilevel relationships among ants, plants and Lepidoptera (primarily butterflies). Indeed, particular traits of ants as eusocial organisms allowed the evolution and the maintenance of a variety of associations with both plants and animals. Basic concepts of myrmecophilous interactions and chemical deception strategies together with chemical composition, biosynthetic pathways and functions of CHCs as molecular cues of multitrophic systems are provided. Finally, the need to adopt a multidisciplinary and comprehensive approach in the survey of complex models is discussed. PMID:27886144

Cuticular Lipids as a Cross-Talk among Ants, Plants and Butterflies.

PubMed

Barbero, Francesca

2016-11-24

Even though insects and plants are distantly related organisms, they developed an integument which is functionally and structurally similar. Besides functioning as a physical barrier to cope with abiotic and biotic stress, this interface, called cuticle, is also a source of chemical signaling. Crucial compounds with this respect are surface lipids and especially cuticular hydrocarbons (CHCs). This review is focused on the role of CHCs in fostering multilevel relationships among ants, plants and Lepidoptera (primarily butterflies). Indeed, particular traits of ants as eusocial organisms allowed the evolution and the maintenance of a variety of associations with both plants and animals. Basic concepts of myrmecophilous interactions and chemical deception strategies together with chemical composition, biosynthetic pathways and functions of CHCs as molecular cues of multitrophic systems are provided. Finally, the need to adopt a multidisciplinary and comprehensive approach in the survey of complex models is discussed.

Analytical Capability of Defocused µ-SORS in the Chemical Interrogation of Thin Turbid Painted Layers

PubMed Central

Realini, Marco; Botteon, Alessandra; Colombo, Chiara; Noll, Sarah; Elliott, Stephen R.; Matousek, Pavel

2016-01-01

A recently developed micrometer-scale spatially offset Raman spectroscopy (μ-SORS) method provides a new analytical capability for investigating non-destructively the chemical composition of sub-surface, micrometer-scale thickness, diffusely scattering layers at depths beyond the reach of conventional confocal Raman microscopy. Here, we demonstrate experimentally, for the first time, the capability of μ-SORS to determine whether two detected chemical components originate from two separate layers or whether the two components are mixed together in a single layer. Such information is important in a number of areas, including conservation of cultural heritage objects, and is not available, for highly turbid media, from conventional Raman microscopy, where axial (confocal) scanning is not possible due to an inability to facilitate direct imaging within the highly scattering sample. This application constitutes an additional capability for μ-SORS in addition to its basic capacity to determine the overall chemical make-up of layers in a turbid system. PMID:26767641

The chemical composition and mineralogy of meteorites measured with very high spatial resolution by a laser mass spectrometer for in situ planetary research

NASA Astrophysics Data System (ADS)

Brigitte Neuland, Maike; Mezger, Klaus; Tulej, Marek; Frey, Samira; Riedo, Andreas; Wurz, Peter; Wiesendanger, Reto

2017-04-01

The knowledge of the chemical composition of moons, comets, asteroids or other planetary bodies is of particular importance for the investigation of the origin and evolution of the Solar System. High resolution in situ studies on planetary surfaces can yield important information on surface heterogeneity, basic grain mineralogy and chemical composition of surface and subsurface. In turn, these data are the basis for our understanding of the physical and chemical processes which led to the formation and alteration of planetary material [1]. We investigated samples of Allende and Sayh al Uhaymir with a highly miniaturised laser mass spectrometer (LMS), which has been designed and built for in situ space research [2,3]. Both meteorite samples were investigated with a spatial resolution of about 10μm in lateral direction. The high sensitivity and high dynamic range of the LMS allow for quantitative measurements of the abundances of the rock-forming and minor and trace elements with high accuracy [4]. From the data, the modal mineralogy of micrometre-sized chondrules can be inferred [5], conclusions about the condensation sequence of the material are possible and the sensitivity for radiogenic elements allows for dating analyses of the investigated material. We measured the composition of various chondrules in Allende, offering valuable clues about the condensation sequence of the different components of the meteorite. We explicitly investigated the chemical composition and heterogeneity of the Allende matrix with an accuracy that cannot be reached by the mechanical analysis methods that were and are widely used in meteoritic research. We demonstrate the capabilities for dating analyses with the LMS. By applying the U-Th-dating method, the age of the SaU169 sample could be determined. Our analyses show that the LMS would be a suitable instrument for high-quality quantitative chemical composition measurements on the surface of a celestial body like a planet, moon or asteroid. [1] Wurz, P., Whitby, J., Managadze, G. , "Laser Mass Spectrometry in Planetary Science", AIP Conf.Proc. CP1144(2009): 70-75. [2] Rohner, U., Whitby, J.A. and Wurz, P. "A miniature laser ablation time-of-flight mass spectrometer for in situ planetary exploration", Measurement Science and Technology 14 (2003): 2159-2164. [3] Riedo, A., Bieler, A., Neuland, M., Tulej, M. and Wurz, P., "Performance evaluation of a miniature laser ablation time-of-flight mass spectrometer designed for in situ investigations in planetary space research", Journal of Mass Spectrometry 48 (2013): 1 -15 [4] Neuland, M.B., Grimaudo, V., Mezger, K., Moreno-García, P., Riedo, A., Tulej, M. and Wurz, P., "Quantitative measurement of the chemical composition of geological standards with a miniature laser ablation/ionisation mass spectrometer designed for in situ application in space research", Meas. Sci. Technol. 27(2016), article ID:035904, 1 - 13. [5] Tulej, M., Neubeck, A., Ivarsson, M., Riedo, A., Neuland, M.B., Meyer, S. and Wurz, P., "Chemical composition of micrometer-sized filaments in an aragonite host by a miniature laser ablation/ionization mass spectrometer", Astrobiol., 15 (2015): 669 - 682.

Technique development for modulus, microcracking, hermeticity, and coating evaluation capability characterization of SiC/SiC tubes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Xunxiang; Ang, Caen K.; Singh, Gyanender P.

Driven by the need to enlarge the safety margins of nuclear fission reactors in accident scenarios, research and development of accident-tolerant fuel has become an important topic in the nuclear engineering and materials community. A continuous-fiber SiC/SiC composite is under consideration as a replacement for traditional zirconium alloy cladding owing to its high-temperature stability, chemical inertness, and exceptional irradiation resistance. An important task is the development of characterization techniques for SiC/SiC cladding, since traditional work using rectangular bars or disks cannot directly provide useful information on the properties of SiC/SiC composite tubes for fuel cladding applications. At Oak Ridge Nationalmore » Laboratory, experimental capabilities are under development to characterize the modulus, microcracking, and hermeticity of as-fabricated, as-irradiated SiC/SiC composite tubes. Resonant ultrasound spectroscopy has been validated as a promising technique to evaluate the elastic properties of SiC/SiC composite tubes and microcracking within the material. A similar technique, impulse excitation, is efficient in determining the basic mechanical properties of SiC bars prepared by chemical vapor deposition; it also has potential for application in studying the mechanical properties of SiC/SiC composite tubes. Complete evaluation of the quality of the developed coatings, a major mitigation strategy against gas permeation and hydrothermal corrosion, requires the deployment of various experimental techniques, such as scratch indentation, tensile pulling-off tests, and scanning electron microscopy. In addition, a comprehensive permeation test station is being established to assess the hermeticity of SiC/SiC composite tubes and to determine the H/D/He permeability of SiC/SiC composites. This report summarizes the current status of the development of these experimental capabilities.« less

A new thermally immobilized fluorinated stationary phase for RP-HPLC.

PubMed

Maldaner, Liane; Jardim, Isabel C S F

2010-02-01

A new fluorinated stationary phase was prepared through thermal immobilization of poly(methyl-3,3,3-trifluoropropylsiloxane) onto 5 microm Kromasil silica particles. The best conditions of immobilization time and temperature were determined through a central composite design and response surface methodologies. Physical-chemical characterization using solid-state (29)Si NMR measurements, infrared spectroscopy and elemental analysis showed that the immobilization process was effective to promote a coating of the support that corresponds to a monolayer of polymer. The stationary phase presents selectivity for positional isomers and good peak shape for basic compounds.

Articular cartilage. Part I. The normal joint.

PubMed

Muehleman, C; Arsenis, C H

1995-05-01

Articular hyaline cartilage is of interest to both the clinician and the basic scientist because of its unique physical and chemical properties which are a consequence of its biochemical composition. Although it is a tissue which is hypocellular, avascular, and also lacks nerves and lymphatics, it is active in synthesis and degradation. Articular cartilage responds to the forces to which it is subjected and, in this way, maintains its integrity as long as those forces do not exceed the tissue's capacity for repair or permanently change the biologic response of the cells.

Method of forming a chemical composition

DOEpatents

Bingham, Dennis N.; Wilding, Bruce M.; Klingler, Kerry M.; Zollinger, William T.; Wendt, Kraig M.

2007-10-09

A method of forming a chemical composition such as a chemical hydride is described and which includes the steps of selecting a composition having chemical bonds and which is capable of forming a chemical hydride; providing a source of hydrogen; and exposing the selected composition to an amount of ionizing radiation to encourage the changing of the chemical bonds of the selected composition, and chemically reacting the selected composition with the source of hydrogen to facilitate the formation of a chemical hydride.

Atomic scale structure and chemistry of interfaces by Z-contrast imaging and electron energy loss spectroscopy in the STEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGibbon, M.M.; Browning, N.D.; Chisholm, M.F.

The macroscopic properties of many materials are controlled by the structure and chemistry at the grain boundaries. A basic understanding of the structure-property relationship requires a technique which probes both composition and chemical bonding on an atomic scale. The high-resolution Z-contrast imaging technique in the scanning transmission electron microscope (STEM) forms an incoherent image in which changes in atomic structure and composition can be interpreted intuitively. This direct image allows the electron probe to be positioned over individual atomic columns for parallel detection electron energy loss spectroscopy (PEELS) at a spatial resolution approaching 0.22nm. The bonding information which can bemore » obtained from the fine structure within the PEELS edges can then be used in conjunction with the Z-contrast images to determine the structure at the grain boundary. In this paper we present 3 examples of correlations between the structural, chemical and electronic properties at materials interfaces in metal-semiconductor systems, superconducting and ferroelectric materials.« less

Chemical composition, starch digestibility and antioxidant capacity of tortilla made with a blend of quality protein maize and black bean.

PubMed

Grajales-García, Eva M; Osorio-Díaz, Perla; Goñi, Isabel; Hervert-Hernández, Deisy; Guzmán-Maldonado, Salvador H; Bello-Pérez, Luis A

2012-01-01

Tortilla and beans are the basic components in the diet of people in the urban and rural areas of Mexico. Quality protein maize is suggested for tortilla preparation because it presents an increase in lysine and tryptophan levels. Beans contain important amounts of dietary fiber. The objective of this study was to prepare tortilla with bean and assesses the chemical composition, starch digestibility and antioxidant capacity using a quality protein maize variety. Tortilla with bean had higher protein, ash, dietary fiber and resistant starch content, and lower digestible starch than control tortilla. The hydrolysis rate (60 to 50%) and the predicted glycemic index (88 to 80) of tortilla decreased with the addition of bean in the blend. Extractable polyphenols and proanthocyanidins were higher in the tortilla with bean than control tortilla. This pattern produced higher antioxidant capacity of tortilla with bean (17.6 μmol Trolox eq/g) than control tortilla (7.8 μmol Trolox eq/g). The addition of bean to tortilla modified the starch digestibility and antioxidant characteristics of tortilla, obtaining a product with nutraceutical characteristics.

Erratum: ``A Grid of Non-LTE Line-blanketed Model Atmospheres of O-Type Stars'' (ApJS, 146, 417 [2003])

NASA Astrophysics Data System (ADS)

Lanz, Thierry; Hubeny, Ivan

2003-07-01

We have constructed a comprehensive grid of 680 metal line-blanketed, non-LTE, plane-parallel, hydrostatic model atmospheres for the basic parameters appropriate to O-type stars. The OSTAR2002 grid considers 12 values of effective temperatures, 27,500K<=Teff<=55,000 K with 2500 K steps, eight surface gravities, 3.0<=logg<=4.75 with 0.25 dex steps, and 10 chemical compositions, from metal-rich relative to the Sun to metal-free. The lower limit of logg for a given effective temperature is set by an approximate location of the Eddington limit. The selected chemical compositions have been chosen to cover a number of typical environments of massive stars: the Galactic center, the Magellanic Clouds, blue compact dwarf galaxies like I Zw 18, and galaxies at high redshifts. The paper contains a description of the OSTAR2002 grid and some illustrative examples and comparisons. The complete OSTAR2002 grid is available at our Web site at ApJS, 146, 417 [2003]. Laboratory for Astronomy and Solar Physics, NASA Goddard Space Flight Center, Code 681, Greenbelt, MD 20771.

Structural building principles of complex face-centered cubic intermetallics.

PubMed

Dshemuchadse, Julia; Jung, Daniel Y; Steurer, Walter

2011-08-01

Fundamental structural building principles are discussed for all 56 known intermetallic phases with approximately 400 or more atoms per unit cell and space-group symmetry F43m, Fd3m, Fd3, Fm3m or Fm3c. Despite fundamental differences in chemical composition, bonding and electronic band structure, their complex crystal structures show striking similarities indicating common building principles. We demonstrate that the structure-determining elements are flat and puckered atomic {110} layers stacked with periodicities 2p. The atoms on this set of layers, which intersect each other, form pentagon face-sharing endohedral fullerene-like clusters arranged in a face-centered cubic packing (f.c.c.). Due to their topological layer structure, all these crystal structures can be described as (p × p × p) = p(3)-fold superstructures of a common basic structure of the double-diamond type. The parameter p, with p = 3, 4, 7 or 11, is determined by the number of layers per repeat unit and the type of cluster packing, which in turn are controlled by chemical composition.

Environmental and seasonal impacts on the chemical composition of Satureja horvatii Šilić (Lamiaceae) essential oils.

PubMed

Lakušić, Branislava; Ristić, Mihailo; Slavkovska, Violeta; Milenković, Marina; Lakušić, Dmitar

2011-03-01

The chemical composition of the essential oils of Satureja horvatii Šilić from two natural habitats (Mt. Orjen and Mt. Lovćen in Montenegro) and from cultivated plants (Belgrade, Serbia) were characterized. For the latter, plants from the locus classicus, i.e., Orjenske Lokve (Mt. Orjen), were transferred to Belgrade and, after three years of cultivation, the chemical composition of their essential oils at different phenological stages was analyzed. The essential oils were obtained from the aerial parts of the plants by hydrodistillation and analyzed by GC and GC/MS. The yields and chemical compositions of the S. horvatii oils showed significant differences between the plants collected in the natural habitats and those from cultivation, as well as between the plants at different phenological stages. In the populations from the natural habitats, growing in Mediterranean conditions, the most abundant oil constituents were the phenols thymol (63.7% in the samples from Mt. Orjen) or carvacrol (68.1% in the samples from Mt. Lovćen), while the oils from the cultivated plants (Belgrade), growing in continental conditions, were dominated by linalool (up to 65.8 and 55.9% in average). The basic characteristics of the essential oil from plants at the early phenological stage (before flowering) were high percentages of linalool (37.4%), thymol (27.3%), and carvacrol (12.2%). At the stage of flowering, the percentage of linalool (56.6-57.5%) increased, while those of thymol (15.5-15.8%) and carvacrol (1.4-1.5%) significantly decreased. The essential oil of plants in the full stage of fruiting was characterized by the domination of linalool (58.4 and 65.8%) and lower percentages of thymol (7.6 and 1.3%) and carvacrol (0.7 and 0.1%). In conclusion, the oil composition of S. horvatii was found to depend on the pedoclimatic conditions of the habitat and the phenological stage of the plants. Copyright © 2011 Verlag Helvetica Chimica Acta AG, Zürich.

Applications of RIGAKU Dmax Rapid II micro-X-ray diffractometer in the analysis of archaeological metal objects

NASA Astrophysics Data System (ADS)

Mozgai, Viktória; Szabó, Máté; Bajnóczi, Bernadett; Weiszburg, Tamás G.; Fórizs, István; Mráv, Zsolt; Tóth, Mária

2017-04-01

During material analysis of archaeological metal objects, especially their inlays or corrosion products, not only microstructure and chemical composition, but mineralogical composition is necessary to be determined. X-ray powder diffraction (XRD) is a widely-used method to specify the mineralogical composition. However, when sampling is not or limitedly allowed due to e.g. the high value of the object, the conventional XRD analysis can hardly be used. Laboratory micro-XRD instruments provide good alternatives, like the RIGAKU Dmax Rapid II micro-X-ray diffractometer, which is a unique combination of a MicroMax-003 third generation microfocus, sealed tube X-ray generator and a curved 'image plate' detector. With this instrument it is possible to measure as small as 10 µm area in diameter on the object. Here we present case studies for the application of the micro-XRD technique in the study of archaeological metal objects. In the first case niello inlay of a Late Roman silver augur staff was analysed. Due to the high value of the object, since it is the only piece known from the Roman Empire, only non-destructive analyses were allowed. To reconstruct the preparation of the niello, SEM-EDX analysis was performed on the niello inlays to characterise their chemical composition and microstructure. Two types of niello are present: a homogeneous, silver sulphide niello (acanthite) and an inhomogeneous silver-copper sulphide niello (exsolution of acanthite and jalpaite or jalpaite and stromeyerite). The micro-X-ray diffractometer was used to verify the mineralogical composition of the niello, supposed on the base of SEM results. In the second case corrosion products of a Late Roman copper cauldron with uncertain provenance were examined, since they may hold clues about the burial conditions (pH, Eh, etc.) of the object. A layer by layer analysis was performed in cross sections of small metal samples by using electron microprobe and micro-X-ray diffractometer. The results show two corrosion zones: 1) the original (internal) surface zone of the metallic copper object was replaced by copper(I) oxide (cuprite), while 2) basic copper(II) carbonate (malachite) was deposited (externally) on the original surface. In our view these two minerals were formed during long-time burial, and protected the cauldron from further corrosion. Rarely copper(I) chloride (nantokite), basic copper(II) trihydroxychloride (atacamite/paratacamite) and basic copper(II) sulphate (brochantite) were also identified in the two corrosion zones. Their uneven distribution on the cauldron and their known formation conditions indicate, that these latter mineral phases may be the results of active corrosion, started possibly after excavation.

Systematic variations in the spectral properties of bright regions on Mars

NASA Technical Reports Server (NTRS)

Murchie, Scott; Mustard, John; Bishop, Janice; Head, James; Pieters, Carle; Erard, Stephane

1992-01-01

The color and albedo of the martian surface define two basic surface units, dark gray material interpreted as relatively unaltered 'rock' and bright reddish material interpreted as weathered 'soil'. Understanding the processes contributing to soil formation first requires assessment of the soil's composition and compositional diversity. We report first results of an investigation of the character and variability of Fe- and water-bearing phases in bright reddish materials using ISM data. We also explore implications of these results for chemical evolution of martian soil. Information on the composition and distribution of bright reddish material comes from three major sources: Viking images, measurements by the XRF and GCMS instruments on the Viking Landers, and spectroscopic data. The XRF experiment found nearly identical, Fe-rich major-element compositions comparable to weathered basalt. Soil water, amounting to approximately 1-3 wt. percent as measured by the GCMS, was liberated mostly by heating to greater than or equal to 350 C, suggesting that it is present in a chemically bound form. Spectroscopic studies have detected ferric oxide, probably hematite, as well as molecular water. However, the identities of major silicate phases have been controversial, with conflicting evidence regarding phyllosilicates. Two main interpretations of this evidence have been proposed: Weathering of basaltic glasses by H2O and CO2 formed a mixture of oxides, salts, and metastable phyllosilicates such as montmorillonite and 'palagonite' formed when basaltic melt contacted ground ice or water. Palagonite is a hydrated basaltic glass containing dispersed ferric oxide, recrystallized in varying degrees to phyllosilicates. Typically it is aphanitic, although some examples contain phenocrysts. In either case, eolian redistribution is thought to have resulted in the material's global homogenization. Imaging spectroscopic data returned by the ISM instrument on Phobos 2 provide a powerful new basis for evaluating the composition and origin of martian soil because they are indicative of the presence and distribution of water- and Fe-bearing phases whose mineralogy is sensitive to the history of chemical weathering.

Chemical Species in the Vapor Phase of Hanford Double-Shell Tanks: Potential Impacts on Waste Tank Corrosion Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Felmy, Andrew R.; Qafoku, Odeta; Arey, Bruce W.

2010-09-22

The presence of corrosive and inhibiting chemicals on the tank walls in the vapor space, arising from the waste supernatant, dictate the type and degree of corrosion that occurs there. An understanding of how waste chemicals are transported to the walls and the affect on vapor species from changing supernatant chemistry (e.g., pH, etc.), are basic to the evaluation of risks and impacts of waste changes on vapor space corrosion (VSC). In order to address these issues the expert panel workshop on double-shell tank (DST) vapor space corrosion testing (RPP-RPT-31129) participants made several recommendations on the future data and modelingmore » needs in the area of DST corrosion. In particular, the drying of vapor phase condensates or supernatants can form salt or other deposits at the carbon steel interface resulting in a chemical composition at the near surface substantially different from that observed directly in the condensates or the supernatants. As a result, over the past three years chemical modeling and experimental studies have been performed on DST supernatants and condensates to predict the changes in chemical composition that might occur as condensates or supernatants equilibrate with the vapor space species and dry at the carbon steel surface. The experimental studies included research on both the chemical changes that occurred as the supernatants dried as well as research on how these chemical changes impact the corrosion of tank steels. The chemical modeling and associated experimental studies were performed at the Pacific Northwest National Laboratory (PNNL) and the research on tank steel corrosion at the Savannah River National Laboratory (SRNL). This report presents a summary of the research conducted at PNNL with special emphasis on the most recent studies conducted in FY10. An overall summary of the project results as well as their broader implications for vapor space corrosion of the DST’s is given at the end of this report.« less

Solution synthesis of metal oxides for electrochemical energy storage applications.

PubMed

Xia, Xinhui; Zhang, Yongqi; Chao, Dongliang; Guan, Cao; Zhang, Yijun; Li, Lu; Ge, Xiang; Bacho, Ignacio Mínguez; Tu, Jiangping; Fan, Hong Jin

2014-05-21

This article provides an overview of solution-based methods for the controllable synthesis of metal oxides and their applications for electrochemical energy storage. Typical solution synthesis strategies are summarized and the detailed chemical reactions are elaborated for several common nanostructured transition metal oxides and their composites. The merits and demerits of these synthesis methods and some important considerations are discussed in association with their electrochemical performance. We also propose the basic guideline for designing advanced nanostructure electrode materials, and the future research trend in the development of high power and energy density electrochemical energy storage devices.

Basic properties and variability

NASA Technical Reports Server (NTRS)

Querci, Francois R.

1987-01-01

Giant and supergiant M, S, and C stars are discussed in this survey of research. Basic properties as determined by spectra, chemical composition, photometry, or variability type are discussed. Space motions and space distributions of cool giants are described. Distribution of these stars in our galaxy and those nearby is discussed. Mira variables in particular are surveyed with emphasis on the following topics: (1) phase lag phenomenon; (2) Mira light curves; (3) variations in color indices; (4) determination of multiple periods; (5) correlations between quantities such as period length, light-curve shape, infrared (IR) excess, and visible and IR color diagram; (6) semiregular (SR) variables and different time scales in SR light variations; (7) irregular variable Lb and Lc stars; (8) different time-scale light variations; (9) hydrogen-deficient carbon (HdC) stars, in particular RCB stars; and (10) irreversible changes and rapid evolution in red variable stars.

Influence of Additives on Masonry and Protective Paints’ Quality

NASA Astrophysics Data System (ADS)

Kostiunina, I. L.; Vyboishchik, A. V.

2017-11-01

The environment is one of main factors influencing the living conditions of urban population in Russia nowadays. One of the main drawbacks restraining the aesthetic improvement process of modern Russian cities is unsatisfactory protection of buildings from atmospheric phenomena. Moreover, industrial waste in modern industrial cities of Russia prevents a long-lasting decoration of urban buildings. The article presents an overview of the composition and physical properties of masonry paints applied in the Chelyabinsk region. The traditional technology of coatings obtaining is studied, the drawbacks of this technology are examined, the new materials and applications are offered. The influence of additives on the basic properties of masonry paints, viz. weather resistance, viscosity, hardness, cost, is considered. The application of new technologies utilizing industrial waste can solve the abovestated problem, which also, along with improving basic physical and chemical properties, will result in the cost reduction and the increase of the masonry paints hardness.

Basic Chemistry for the Cement Industry.

ERIC Educational Resources Information Center

Turner, Mason

This combined student workbook and instructor's guide contains nine units for inplant classes on basic chemistry for employees in the cement industry. The nine units cover the following topics: chemical basics; measurement; history of cement; atoms; bonding and chemical formulas; solids, liquids, and gases; chemistry of Portland cement…

The ACEE program and basic composites research at Langley Research Center (1975 to 1986): Summary and bibliography

NASA Technical Reports Server (NTRS)

Dow, Marvin B.

1987-01-01

Composites research conducted at the Langley Research Center during the period from 1975 to 1986 is described, and an annotated bibliography of over 600 documents (with their abstracts) is presented. The research includes Langley basic technology and the composite primary structures element of the NASA Aircraft Energy Efficiency (ACEE) Program. The basic technology documents cited in the bibliography are grouped according to the research activity such as design and analysis, fatigue and fracture, and damage tolerance. The ACEE documents cover development of composite structures for transport aircraft.

Preparation and corrosion resistance of magnesium phytic acid/hydroxyapatite composite coatings on biodegradable AZ31 magnesium alloy.

PubMed

Zhang, Min; Cai, Shu; Zhang, Feiyang; Xu, Guohua; Wang, Fengwu; Yu, Nian; Wu, Xiaodong

2017-06-01

In this work, a magnesium phytic acid/hydroxyapatite composite coating was successfully prepared on AZ31 magnesium alloy substrate by chemical conversion deposition technology with the aim of improving its corrosion resistance and bioactivity. The influence of hydroxyapatite (HA) content on the microstructure and corrosion resistance of the coatings was investigated. The results showed that with the increase of HA content in phytic acid solution, the cracks on the surface of the coatings gradually reduced, which subsequently improved the corrosion resistance of these coated magnesium alloy. Electrochemical measurements in simulated body fluid (SBF) revealed that the composite coating with 45 wt.% HA addition exhibited superior surface integrity and significantly improved corrosion resistance compared with the single phytic acid conversion coating. The results of the immersion test in SBF showed that the composite coating could provide more effective protection for magnesium alloy substrate than that of the single phytic acid coating and showed good bioactivity. Magnesium phytic acid/hydroxyapatite composite, with the desired bioactivity, can be synthesized through chemical conversion deposition technology as protective coatings for surface modification of the biodegradable magnesium alloy implants. The design idea of the new type of biomaterial is belong to the concept of "third generation biomaterial". Corrosion behavior and bioactivity of coated magnesium alloy are the key issues during implantation. In this study, preparation and corrosion behavior of magnesium phytic acid/hydroxyapatite composite coatings on magnesium alloy were studied. The basic findings and significance of this paper are as follows: 1. A novel environmentally friendly, homogenous and crack-free magnesium phytic acid/hydroxyapatite composite coating was fabricated on AZ31 magnesium alloy via chemical conversion deposition technology with the aim of enhancing its corrosion resistance and bioactivity. The chemical conversion coatings, which are formed through the reaction between the substrate and the environment, have attracted increasing attention owing to the relative low treatment temperature, favorable bonding to substrate and simple implementation process. 2. With the increasing of hydroxyapatite (HA) content, the crack width in the composite coatings and the thickness of the coatings exhibit obviously decreased. The reason is probably that when adding HA into the phytic acid solution, the amount of active hydroxyl groups in the phytic acid are reduced via forming the coordination bond between P-OH groups from phytic acid and P-OH groups from the surface of HA, thus decreasing the coating thickness and hydrogen formation, as well as avoiding coating cracking. 3. By adjusting the HA content to 45 wt.%, a dense and relatively smooth composite coating with ~1.4 μm thickness is obtained on magnesium alloy, and exhibits high corrosion resistance and good bioactivity when compared with the single phytic acid conversion coating.

Thermodynamics of DL-alanine solvation in water-dimethylsulfoxide mixtures at 298.15 K

NASA Astrophysics Data System (ADS)

Roy, S.; Mahali, K.; Mondal, S.; Dolui, B. K.

2015-04-01

In this study we mainly discuss the transfer Gibbs free energy Δ G {/t 0}( i) and Δ S {/t 0}( i)entropy of DL-alanine at 298.15 K and consequently the involved chemical transfer free energy (Δ G {/t,ch 0}( i)) and entropy ( TΔ S {/t,ch 0}( i)) in aqueous mixtures of dimethylsulfoxide are discussed to clarify the solvation chemistry of DL-alanine. For the evaluation of these energy terms, solubility of this amino acid has been measured by formol titrimetry at five equidistant temperatures i.e., from 288.15 to 308.15 K in different composition of this mixed solvent system. The various solvent parameters as well as thermodynamic parameters like molar volume, density, dipole moment and solvent diameter of this solvent system have also been reported here. The chemical effects of the transfer Gibbs energies (Δ G {/t,ch 0}( i)) and entropies of transfer ( TΔ S {/t,ch 0}( i)) have been obtained after elimination of cavity effect and dipole-dipole interaction effects from the total transfer energies. Here the chemical contribution of transfer energetics of DL-alanine is mainly guided by the composite effects of increased dispersion interaction, basicity effect and decreased acidity, hydrogen bonding effects, hydrophilic hydration and hydrophobic hydration of aqueous DMSO mixtures as compared to that of reference solvent, water.

DISCUSSION ON ADVANCES IN THE TREATMENT OF URÆMIA

PubMed Central

1948-01-01

Uræmia is common, little is known of its actual nature and treatment has therefore been unsatisfactory. The kidney is not only an organ of excretion but guards the chemical and physical constitution of the extracellular fluids. In uræmia, urea and other products of metabolism including the toxic phenols accumulate. That the physical and chemical composition of the extracellular fluids, excluding protein, can be influenced by contact across a semi-permeable membrane is the basic concept of the treatment of uræmia by dialysis, whether by means of the artificial kidney or by peritoneal lavage. The principles of treatment of uræmia are: (1) To remove the cause. (2) Reduce the load on the kidney. (3) Assist or take over the function of the failing kidney in the hope that it may recover. (4) To relieve symptoms without thereby prejudicing recovery. Dialysis can be effected by peritoneal lavage or by conducting the circulating blood through a tube of semi-permeable membrane. The composition of the dialysing fluid is of the utmost importance the aim being to keep the physical and chemical balance of the extracellular fluid within the normal range and to encourage the diffusion of toxic metabolic products. The excessive use of parenteral fluids and diuretics in uræmia may be harmful. A number of cases of peritoneal dialysis are described. PMID:18872157

Effect of bioglass 45S5 addition on properties, microstructure and cellular response of tetracalcium phosphate/monetite cements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stulajterova, R., E-mail: rstulajterova@saske.sk

Tetracalcium phosphate/nanomonetite (TTCPMH) cement composites with 7.5 and 15 wt% addition of melt-derived 45S5 bioactive glass were prepared by mechanical homogenization of powder components and 2% NaH{sub 2}PO{sub 4} solution was used as a hardening liquid. The properties of composites with the acidic (Ca/P ratio equal 1.5) or basic (Ca/P ratio equal 1.67) TTCPMH component were compared. Addition of glass component caused rapid rise in pH of composites up to 10. In microstructure of basic cement composite, the large bioglass particles weakly bounded to surrounding cement matrix were found contrary to a more compact microstructure of acidic cement composites withmore » the high number of spherical silica particles. Both the significant refinement of hydroxyapatite particles and the change to needle-like morphology with rise in the content of bioglass were identified in hydroxyapatite coatings created during soaking of composites in phosphate buffered saline. In acidic cement mixtures, the increase of compressive strength with an amount of bioglass was found whereas the opposite tendency was revealed in the case of basic cement mixtures. The higher concentrations of ions were verified in solutions after immersion of acidic cement composites. The severe cytotoxicity of extracts and composite cement substrates containing 15 wt% of bioglass demonstrated adverse effects of both the ionic concentrations and unappropriate surface texture on proliferation of mesenchymal stem cells. The enhanced ALP activities of cells cultured on composite cements confirmed the positive effect of bioactive glass addition on differentiation of mesenchymal stem cells. - Highlights: • Novel B45S5 bioglass/tetracalcium phosphate/nanomonetite cement composites • Cement basicity negatively affected their microstructure. • Acid composite cements had higher compressive strengths than basic composites. • Fast differentiation of MSC to osteoblast line on composite with 7.5 wt% of bioglass • Severe cytotoxicity of 24 h extracts from composites with 15 wt% of bioglass.« less

Representational Competence in Chemistry: A Comparison between Students with Different Levels of Understanding of Basic Chemical Concepts and Chemical Representations

ERIC Educational Resources Information Center

Sim, Joong Hiong; Daniel, Esther Gnanamalar Sarojini

2014-01-01

Representational competence is defined as "skills in interpreting and using representations". This study attempted to compare students' of high, medium, and low levels of understanding of (1) basic chemical concepts, and (2) chemical representations, in their representational competence. A total of 411 Form 4 science students (mean age =…

Atomic scale structure and chemistry of interfaces by Z-contrast imaging and electron energy loss spectroscopy in the stem

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGibbon, M.M.; Browning, N.D.; Chisholm, M.F.

The macroscopic properties of many materials are controlled by the structure and chemistry at grain boundaries. A basic understanding of the structure-property relationship requires a technique which probes both composition and chemical bonding on an atomic scale. High-resolution Z-contrast imaging in the scanning transmission electron microscope (STEM) forms an incoherent image in which changes in atomic structure and composition across an interface can be interpreted directly without the need for preconceived atomic structure models. Since the Z-contrast image is formed by electrons scattered through high angles, parallel detection electron energy loss spectroscopy (PEELS) can be used simultaneously to provide complementarymore » chemical information on an atomic scale. The fine structure in the PEEL spectra can be used to investigate the local electronic structure and the nature of the bonding across the interface. In this paper we use the complimentary techniques of high resolution Z-contrast imaging and PEELS to investigate the atomic structure and chemistry of a 25{degree} symmetric tilt boundary in a bicrystal of the electroceramic SrTiO{sub 3}.« less

Chemical Composition, Starch Digestibility and Antioxidant Capacity of Tortilla Made with a Blend of Quality Protein Maize and Black Bean

PubMed Central

Grajales-García, Eva M.; Osorio-Díaz, Perla; Goñi, Isabel; Hervert-Hernández, Deisy; Guzmán-Maldonado, Salvador H.; Bello-Pérez, Luis A.

2012-01-01

Tortilla and beans are the basic components in the diet of people in the urban and rural areas of Mexico. Quality protein maize is suggested for tortilla preparation because it presents an increase in lysine and tryptophan levels. Beans contain important amounts of dietary fiber. The objective of this study was to prepare tortilla with bean and assesses the chemical composition, starch digestibility and antioxidant capacity using a quality protein maize variety. Tortilla with bean had higher protein, ash, dietary fiber and resistant starch content, and lower digestible starch than control tortilla. The hydrolysis rate (60 to 50%) and the predicted glycemic index (88 to 80) of tortilla decreased with the addition of bean in the blend. Extractable polyphenols and proanthocyanidins were higher in the tortilla with bean than control tortilla. This pattern produced higher antioxidant capacity of tortilla with bean (17.6 μmol Trolox eq/g) than control tortilla (7.8 μmol Trolox eq/g). The addition of bean to tortilla modified the starch digestibility and antioxidant characteristics of tortilla, obtaining a product with nutraceutical characteristics. PMID:22312252

Alkaline Activator Impact on the Geopolymer Binders

NASA Astrophysics Data System (ADS)

Błaszczyński, Tomasz Z.; Król, Maciej R.

2017-10-01

Concrete structures are constantly moving in the direction of improving the durability. Durability depends on many factors, which are the composition of concrete mix, the usage of additives and admixtures and the place, where material will work and carry the load. The introduction of new geopolymer binders for geopolymer structures adds a new aspect that is type of used activator. This substance with strongly alkaline reaction is divided because of the physical state, the alkaline degree and above all the chemical composition. Taking into account, that at present the geopolymer binders are made essentially from waste materials or by-products from the combustion of coal or iron ore smelting, unambiguous determination of the effect of the activator on the properties of the geopolymer material requires a number of trials, researches and observation. This paper shows the influence of the most alkaline activators on the basic parameters of the durability of geopolymer binders. In this study there were used highly alkaline hydroxides, water glasses and granules, which are waste materials in a variety of processes taking place in chemical plants. As the substrate of geopolymer binders there were used fly ash which came from coal and high calcareous ash from the burning of lignite.

Vacuum pyrolysis of waste tires with basic additives.

PubMed

Zhang, Xinghua; Wang, Tiejun; Ma, Longlong; Chang, Jie

2008-11-01

Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na2CO3, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 degrees C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) approximately 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na2CO3 addition. Pyrolysis gas was mainly composed of H2, CO, CH4, CO2, C2H4 and C2H6. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

Chemical Biodynamics Division. Annual report 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-08-01

The Chemical Biodynamics Division of LBL continues to conduct basic research on the dynamics of living cells and on the interaction of radiant energy with organic matter. Many aspects of this basic research are related to problems of environmental and health effects of fossil fuel combustion, solar energy conversion and chemical/ viral carcinogenesis.

Chemical compositions, methods of making the chemical compositions, and structures made from the chemical compositions

DOEpatents

Yang, Lei; Cheng, Zhe; Liu, Ze; Liu, Meilin

2015-01-13

Embodiments of the present disclosure include chemical compositions, structures, anodes, cathodes, electrolytes for solid oxide fuel cells, solid oxide fuel cells, fuel cells, fuel cell membranes, separation membranes, catalytic membranes, sensors, coatings for electrolytes, electrodes, membranes, and catalysts, and the like, are disclosed.

Nectar and pollination drops: how different are they?

PubMed

Nepi, Massimo; von Aderkas, Patrick; Wagner, Rebecca; Mugnaini, Serena; Coulter, Andrea; Pacini, Ettore

2009-08-01

Pollination drops and nectars (floral nectars) are secretions related to plant reproduction. The pollination drop is the landing site for the majority of gymnosperm pollen, whereas nectar of angiosperm flowers represents a common nutritional resource for a large variety of pollinators. Extrafloral nectars also are known from all vascular plants, although among the gymnosperms they are restricted to the Gnetales. Extrafloral nectars are not generally involved in reproduction but serve as 'reward' for ants defending plants against herbivores (indirect defence). Although very different in their task, nectars and pollination drops share some features, e.g. basic chemical composition and eventual consumption by animals. This has led some authors to call these secretions collectively nectar. Modern techniques that permit chemical analysis and protein characterization have very recently added important information about these sugary secretions that appear to be much more than a 'reward' for pollinating (floral nectar) and defending animals (extrafloral nectar) or a landing site for pollen (pollination drop). Nectar and pollination drops contain sugars as the main components, but the total concentration and the relative proportions are different. They also contain amino acids, of which proline is frequently the most abundant. Proteomic studies have revealed the presence of common functional classes of proteins such as invertases and defence-related proteins in nectar (floral and extrafloral) and pollination drops. Invertases allow for dynamic rearrangement of sugar composition following secretion. Defence-related proteins provide protection from invasion by fungi and bacteria. Currently, only few species have been studied in any depth. The chemical composition of the pollination drop must be investigated in a larger number of species if eventual phylogenetic relationships are to be revealed. Much more information can be provided from further proteomic studies of both nectar and pollination drop that will contribute to the study of plant reproduction and evolution.

75 FR 54149 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-03

... current basic case-mix adjusted composite payment system and the methodologies for the reimbursement of... during the transition will be paid under the basic case-mix adjusted composite payment system. Form...

Bases of the Mantle-Carbonatite Conception of Diamond Genesis

NASA Astrophysics Data System (ADS)

Litvin, Yuriy; Spivak, Anna; Kuzyura, Anastasia

2016-04-01

In the mantle-carbonatite conception of diamond genesis, the results of physic-chemical experiments are coordinated with the data of analytic mineralogy of primary inclusions in natural diamonds. Generalization of the solutions of principal genetic problems constitutes the bases of the conception. The solutions are following: (1) it is grounded that diamond-parental melts of the upper mantle have peridotite/eclogite - carbonatite - carbon compositions, of the transition zone - (wadsleite↔ringwoodite) - majorite - stishovite - carbonatite - carbon compositions, and of the lower mantle - periclase/wustite - bridgmanite - Ca-perovskite -stishovite - carbonatite - carbon compositions; (2) a construction of generalized diagrams for the diamond-parental media, which reveal changeable compositions of the growth melts of diamonds and associated phases, their genetic relations to the mantle substance, and classification connections of the primary inclusions in natural diamonds; (3) experimental equilibrium phase diagrams of syngenesis of diamonds and primary inclusions, which characterize the nucleation and growth conditions of diamonds and a capture of paragenetic and xenogenetic minerals by the growing diamonds; (4) a determination of the phase diagrams of diamonds and inclusions syngenesis under the regime of fractional crystallization, which discover the regularities of ultrabasic-basic evolution and paragenesis transitions in the diamond-forming systems of the upper and lower mantle. The evidence of the physic-chemically united mode of diamond genesis at the mantle depths with different mineralogy is obtained. References. Litvin Yu.A. (2007). High-pressure mineralogy of diamond genesis. In: Advances in High-Pressure Mineralogy (edited by Eiji Ohtani), Geological Society of America Special paper 421, 83-103. Litvin Yu.A. (2012). Experimental study of physic-chemical conditions of natural diamond formation on an example of the eclogite-carbonatite-sulphide-diamond system. Geology of Ore Deposits. 54(6), 523-539. Litvin Yu.A., Spivak A.V., Solopova N.A., Dubrovinsky L.S. (2014). On origin of lower-mantle diamonds and their primary inclusions. Physics of the Earth and Planetary Interiors, 228 (The Liebermann Volume), 176-185. http://dx.doi.org/10.1016/j/pepi/2013.12.007

Biocompatibility assessment of SiO2-TiO2 composite powder on MG63 osteoblast cell lines for orthopaedic applications.

PubMed

Chellappa, Maniickam; Thejaswini, Bezawada; Vijayalakshmi, Uthirapathy

2017-02-01

The objective of this study is to evaluate the biocompatibility of composite powder consisting of silica and titania (SiO 2 -TiO 2 ) for biomedical applications. The advancement of nanoscience and nanotechnology encourages researchers to actively participate in reinvention of existing materials with improved physical, chemical and biological properties. Hence, a composite/hybrid material has given birth of new materials with intriguing properties. In the present investigation, SiO 2 -TiO 2 composite powder was synthesised by sol-gel method and the prepared nanocomposite was characterised for its phase purity, functional groups, surface topography by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy. Furthermore, to understand the adverse effects of composite, biocompatibility test was analysed by cell culture method using MG63 osteoblast cell lines as a basic screening method. From the results, it was observed that typical Si-O-Ti peaks in FT-IR confirms the formation of composite and the crystallinity of the composite powder was analysed by XRD analysis. Further in vitro biocompatibility and acridine orange results have indicated better biocompatibility at different concentrations on osteoblast cell lines. On the basis of these observations, we envision that the prepared silica-titania nanocomposite is an intriguing biomaterial for better biomedical applications.

Simulation of uranium and plutonium oxides compounds obtained in plasma

NASA Astrophysics Data System (ADS)

Novoselov, Ivan Yu.; Karengin, Alexander G.; Babaev, Renat G.

2018-03-01

The aim of this paper is to carry out thermodynamic simulation of mixed plutonium and uranium oxides compounds obtained after plasma treatment of plutonium and uranium nitrates and to determine optimal water-salt-organic mixture composition as well as conditions for their plasma treatment (temperature, air mass fraction). Authors conclude that it needs to complete the treatment of nitric solutions in form of water-salt-organic mixtures to guarantee energy saving obtainment of oxide compounds for mixed-oxide fuel and explain the choice of chemical composition of water-salt-organic mixture. It has been confirmed that temperature of 1200 °C is optimal to practice the process. Authors have demonstrated that condensed products after plasma treatment of water-salt-organic mixture contains targeted products (uranium and plutonium oxides) and gaseous products are environmental friendly. In conclusion basic operational modes for practicing the process are showed.

PRE-ORE POTASSIUM METASOMATISM, CREEDE MINING DISTRICT, COLORADO.

USGS Publications Warehouse

Bethke, P.M.; Rye, R.O.; Barton, P.B.

1985-01-01

Rhyolitic welded-tuff wallrocks of the epithermal base and precious metal veins of the Creede district were pervasively altered by the addition of more than two billion metric tons of potassium some 1. 5-2 million years before mineralization. Sodium, calcium and magnesium were strongly depleted, yielding a nearly binary quartz plus potassium feldspar assemblage containing as much as 13 weight percent K//2O. This large-scale metasomatism, originally noted by Steven and Rattle (1965), took place progressively by initial alteration of plagioclase phenocrysts to orthoclase or microcline followed by alteration of the groundmass feldspar to orthoclase and gradual change of the sanidine phenocrysts to more Or-rich compositions. Oxygen isotope and chemical studies show that the metasomatism resulted from the interaction of the tuffs with deeply circulating heated ground water and suggest that the potassium metasomatism of rhyolitic rocks is the facies equivalent of propylitization of volcanic rocks of more basic composition.

Prevention of trace and major element leaching from coal combustion products by hydrothermally-treated coal ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adnadjevic, B.; Popovic, A.; Mikasinovic, B.

2009-07-01

The most important structural components of coal ash obtained by coal combustion in 'Nikola Tesla A' power plant located near Belgrade (Serbia) are amorphous alumosilicate, alpha-quartz, and mullite. The phase composition of coal ash can be altered to obtain zeolite type NaA that crystallizes in a narrow crystallization field (SiO{sub 2}/Al{sub 2}O{sub 3}; Na{sub 2}O/SiO{sub 2}; H{sub 2}O/Na{sub 2}O ratios). Basic properties (crystallization degree, chemical composition, the energy of activation) of obtained zeolites were established. Coal ash extracts treated with obtained ion-exchange material showed that zeolites obtained from coal ash were able to reduce the amounts of iron, chromium, nickel,more » zinc, copper, lead, and manganese in ash extracts, thus proving its potential in preventing pollution from dump effluent waters.« less

Catalysis, nanostructure and macroscopic property triangle in bioactive calcium-containing ceramic systems.

PubMed

Meiszterics, Anikó; Havancsák, Károly; Sinkó, Katalin

2013-04-01

Calcium silicate ceramics are intended for application as long-term implant materials. In the present work, attention was paid to understand the correlations between the nanostructure (aggregate size, crystallinity, porosity) and the macroscopic properties (solubility in water and simulated body fluids, SBF; hardness) varying the chemical composition. Varying the catalyst (from a base to various acids) during the chemical synthesis was shown to significantly impact on the pore size, crystallinity and mechanical properties. The basic catalyst yields the ceramics with the highest mechanical strength. Ammonia used in 1.0 or 10.0 molar ratio results in bulk ceramics with parameters required for a biomedical application, good hardness (180-200 HV) and low solubility (1-3%) in water and in SBF. The fine porosity (~50 nm) and homogeneous amorphous structure induce good mechanical character. Copyright © 2012 Elsevier B.V. All rights reserved.

Aspects of the mechanisms of smoke generation by burning materials

NASA Technical Reports Server (NTRS)

Bankston, C. P.; Zinn, B. T.; Browner, R. F.; Powell, E. A.

1981-01-01

An investigation of smoke generation during the burning of natural and synthetic solid materials (relevant to fire safety problems), under simulated fire conditions, is presented. Smoke formation mechanisms, including flaming and nonflaming combustion, are reviewed, and the complex physical, chemical, and electrical processes, important in smoke particulate production, are identified. With reference to the smoke formation mechanisms, measured experimental data are discussed, and include effects of ventilation gas temperature, dependence on material composition, and chemical analysis of smoke particulates. Significant differences in smoke characteristics are observed between flaming and nonflaming conditions, which is attributed to specific differences in controlling mechanisms and resultant ways leading to particulate formation. The effects of polymer substrate properties and effects of additives for a given substrate on smoke properties are also discussed in terms of basic processes. It is shown that many of the measured trends can be interpreted by considering postulated mechanisms of particulate formation.

A versatile system for biological and soil chemical tests on a planetary landing craft. II - Hardware development

NASA Technical Reports Server (NTRS)

Martin, J. P.; Kok, B.; Radmer, R.

1976-01-01

A system has been under development which is designed to seek remotely for clues to life in planetary soil samples. The basic approach is a set of experiments, all having a common sensor, a gas analysis mass spectrometer which monitors gas composition in the head spaces above sealed, temperature controlled soil samples. Versatility is obtained with up to three preloaded, sealed fluid injector capsules for each of eleven soil test cells. Tests results with an engineering model has demonstrated performance capability of subsystem components such as soil distribution, gas sampling valves, injector mechanisms, temperature control, and test cell seal.

The planet Mars - From antiquity to the present

NASA Astrophysics Data System (ADS)

Kieffer, Hugh H.; Jakosky, Bruce M.; Snyder, Conway W.

Telescopic observations of Mars, from those of Galileo in 1610 to the late 19th century, were summarized by Flammarion (1892, 1909). Major compilations of knowledge of Mars were produced by Antoniadi (1930) and de Vaucouleurs (1954). Polar cap composition was debated until the discovery by the Viking mission that the north and south perennial polar caps are composed of different materials. Spacecraft data indicate a rich and diverse geologic history as well as many unsolved puzzles. An annotated list of books about Mars is provided. Basic physical and chemical data on Mars are summarized in tabular form, and a guide to the Martian seasons is given.

Method of producing hydrogen

DOEpatents

Bingham, Dennis N.; Klingler, Kerry M.; Wilding, Bruce M.; Zollinger, William T.

2006-12-26

A method of producing hydrogen is disclosed and which includes providing a first composition; providing a second composition; reacting the first and second compositions together to produce a chemical hydride; providing a liquid and reacting the chemical hydride with the liquid in a manner to produce a high pressure hydrogen gas and a byproduct which includes the first composition; and reusing the first composition formed as a byproduct in a subsequent chemical reaction to form additional chemical hydride.

Boolean logic tree of graphene-based chemical system for molecular computation and intelligent molecular search query.

PubMed

Huang, Wei Tao; Luo, Hong Qun; Li, Nian Bing

2014-05-06

The most serious, and yet unsolved, problem of constructing molecular computing devices consists in connecting all of these molecular events into a usable device. This report demonstrates the use of Boolean logic tree for analyzing the chemical event network based on graphene, organic dye, thrombin aptamer, and Fenton reaction, organizing and connecting these basic chemical events. And this chemical event network can be utilized to implement fluorescent combinatorial logic (including basic logic gates and complex integrated logic circuits) and fuzzy logic computing. On the basis of the Boolean logic tree analysis and logic computing, these basic chemical events can be considered as programmable "words" and chemical interactions as "syntax" logic rules to construct molecular search engine for performing intelligent molecular search query. Our approach is helpful in developing the advanced logic program based on molecules for application in biosensing, nanotechnology, and drug delivery.

Vapour-phase method in the synthesis of polymer-ibuprofen sodium-silica gel composites.

PubMed

Kierys, Agnieszka; Krasucka, Patrycja; Grochowicz, Marta

2017-11-01

The study discusses the synthesis of polymer-silica composites comprising water soluble drug (ibuprofen sodium, IBS). The polymers selected for this study were poly(TRIM) and poly(HEMA- co -TRIM) produced in the form of permanently porous beads via the suspension-emulsion polymerization method. The acid and base set ternary composites were prepared by the saturation of the solid dispersions of drug (poly(TRIM)-IBS and/or poly(HEMA- co -TRIM)-IBS) with TEOS, and followed by their exposition to the vapour mixture of water and ammonia, or water and hydrochloric acid, at autogenous pressure. The conducted analyses reveal that the internal structure and total porosity of the resulting composites strongly depend on the catalyst which was used for silica precursor gelation. The parameters characterizing the porosity of both of the acid set composites are much lower than the parameters of the base set composites. Moreover, the basic catalyst supplied in the vapour phase does not affect the ibuprofen sodium molecules, whereas the acid one causes transformation of the ibuprofen sodium into the sodium chloride and a derivative of propanoic acid, which is poorly water soluble. The release profiles of ibuprofen sodium from composites demonstrate that there are differences in the rate and efficiency of drug desorption from them. They are mainly affected by the chemical character of the polymeric carrier but are also associated with the restricted swelling of the composites in the buffer solution after precipitation of silica gel.

A comparison of chemical compositions of reported altered oceanic crusts and global MORB data set: implication for isotopic heterogeneity of recycled materials

NASA Astrophysics Data System (ADS)

Shimoda, G.; Kogiso, T.

2017-12-01

Chemical composition of altered oceanic crust is one of important constraints to delineate chemical heterogeneity of the mantle. Accordingly, many researchers have been studied to determine bulk chemical composition of altered oceanic crust mainly based on chemical compositions of old oceanic crusts at Site 801 and Site 417/418, and young crust at Site 504 (e.g., Staudigel et al., 1996; Bach et al. 2003; Kuo et al., 2016). Their careful estimation provided reliable bulk chemical compositions of these Sites and revealed common geochemical feature of alteration. To assess effect of recycling of altered oceanic crust on chemical evolution of the mantle, it might be meaningful to discuss whether the reported chemical compositions of altered oceanic crusts can represent chemical composition of globally subducted oceanic crusts. Reported chemical compositions of fresh glass or less altered samples from Site 801, 417/418 and 504 were highly depleted compared to that of global MORB reported by Gale et al. (2013), suggesting that there might be sampling bias. Hence, it could be important to consider chemical difference between oceanic crusts of these three Sites and global MORB to discuss effect of recycling of oceanic crust on isotopic heterogeneity of the mantle. It has been suggested that one of controlling factors of chemical variation of oceanic crust is crustal spreading rate because different degree of partial melting affects chemical composition of magmas produced at a mid-ocean ridge. Crustal spreading rate could also affect intensity of alteration. Namely, oceanic crusts produced at slow-spreading ridges may prone to be altered due to existence of larger displacement faults compared to fast spreading ridges which have relatively smooth topography. Thus, it might be significant to evaluate isotopic evolution of oceanic crusts those were produced at different spreading rates. In this presentation, we will provide a possible chemical variation of altered oceanic crusts based on reported bulk chemical compositions of altered oceanic crusts and global data sets of MORB. On the basis of the chemical variation, we will discuss isotopic evolution of altered oceanic crusts to delineate isotopic variation of recycled oceanic crusts.

47 CFR 76.920 - Composition of the basic tier.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false Composition of the basic tier. 76.920 Section 76.920 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES... tier of video programming or to purchase any other video programming. ...

47 CFR 76.920 - Composition of the basic tier.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Composition of the basic tier. 76.920 Section 76.920 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES... tier of video programming or to purchase any other video programming. ...

Phase 1: Definition of intercity transportation comparison framework. Volume 1: Summary. [operations research of passenger and freight transporatation systems

NASA Technical Reports Server (NTRS)

1978-01-01

A unified framework for comparing intercity passenger and freight transportation systems is presented. Composite measures for cost, service/demand, energy, and environmental impact were determined. A set of 14 basic measures were articulated to form the foundation for computing the composite measures. A parameter dependency diagram, constructed to explicitly interrelate the composite and basic measures is discussed. Ground rules and methodology for developing the values of the basic measures are provided and the use of the framework with existing cost and service data is illustrated for various freight systems.

Urban Land: Study of Surface Run-off Composition and Its Dynamics

NASA Astrophysics Data System (ADS)

Palagin, E. D.; Gridneva, M. A.; Bykova, P. G.

2017-11-01

The qualitative composition of urban land surface run-off is liable to significant variations. To study surface run-off dynamics, to examine its behaviour and to discover reasons of these variations, it is relevant to use the mathematical apparatus technique of time series analysis. A seasonal decomposition procedure was applied to a temporary series of monthly dynamics with the annual frequency of seasonal variations in connection with a multiplicative model. The results of the quantitative chemical analysis of surface wastewater of the 22nd Partsjezd outlet in Samara for the period of 2004-2016 were used as basic data. As a result of the analysis, a seasonal pattern of variations in the composition of surface run-off in Samara was identified. Seasonal indices upon 15 waste-water quality indicators were defined. BOD (full), suspended materials, mineralization, chlorides, sulphates, ammonium-ion, nitrite-anion, nitrate-anion, phosphates (phosphorus), iron general, copper, zinc, aluminium, petroleum products, synthetic surfactants (anion-active). Based on the seasonal decomposition of the time series data, the contribution of trends, seasonal and accidental components of the variability of the surface run-off indicators was estimated.

Ultrabasic-basic change over primary inclusions in lower-mantle diamonds: Mineralogical and experimental evidence for crucial role of stishovite paradox

NASA Astrophysics Data System (ADS)

Litvin, Yuriy; Spivak, Anna

2017-04-01

Melting relations of the lower-mantle magmatic system MgO - FeO - CaO - SiO2 are characterized by peritectic reaction of bridgmanite (Mg,Fe)SiO3 and melt with formation of Fe-rich phases of periclase-wustite solid solutions (MgO•FeO)ss and stishovite SiO2. The reaction proceeds also in melts-solutions of lower-mantle diamond-parental system MgO - FeO - CaO - SiO2 - (Mg-Fe-Ca-Na-carbonate) - C. Xenoliths of lower mantle rocks were never found among the deep mantle derived materials. Estimation of lower-mantle mineralogy as ferropericlase+ bridgmanite+ Ca-perovskite association is inferred from high-pressure subsolidus experiments with ultrabasic pyrolite composition (Akaogi, 2007). The paradoxical in situ paragenesis of stishovite and ferropericlase as primary inclusions in lower-mantle diamonds (Kaminsky, 2012) takes its explanation from the bridgmanite peritectic reaction (effect of "stishovite paradox") (Litvin et al., 2014). Based on the data for inclusions, physico-chemical study on syngenesis of diamonds and primary inclusions has experimentally revealed the ferropericlase-bridgmanite-Ca-perovskite-stishovite-magnesiowustite-(Mg-Fe-Ca-Na-carbonate)-carbon compositions of the lower-mantle diamond-forming system .(Litvin et al., 2016). The generalized diagram of diamong-forming media characterizes the variable compositions of growths melts for diamonds and paragenetic phases and their genetic relationships with lower mantle matter, and it is the reason for genetic classifying primary inclusions. Fractional ultrabasic-basic evolution and continuous paragenetic transition from ultrabasic bridgmanite-ferropericlase to basic stishovite-magnesiowustite assemblages in the of lower-mantle diamond-parental melts-solutions are providing by the physico-chemical mechanism of stishovite paradox. References Akaogi M. (2007). Phase transformations of minerals in the transition zone and upper part of the lower mantle. In Advances in High-Pressure Mineralogy (Ohtani E., ed.). Geol. Soc. Am. Spec. Paper 421, 1-13. Kaminsky F.V. (2012). Mineralogy of the lower mantle: a review of "supper-deep" mineral inclusions in diamonds. Earth Sci. Rev. 110, 127-147. Litvin Yu.A., Spivak A.V., Solopova N.A., Dubrovinsky L.S. (2014). On origin of lower-mantle diamonds and their primary inclusions. Phys. Earth Planet. Inter. 228, 176-185. Litvin Yu.A., Spivak A.V., Dubrovinsky L.S. (2016). Magmatic evolution of the material of the Earth's lower mantle: stishovite paradox and origin of superdeep diamonds (experiments at 24-26 GPa). Geochemistry Internat. 54(11, 936-947.)

Influence of Sulfur Content on the Corrosion Resistance of 17-4PH Stainless Steel

NASA Astrophysics Data System (ADS)

Tavares, S. S. M.; Pardal, J. M.; Martins, T. R. B.; da Silva, M. R.

2017-04-01

According to specification standards, the basic chemical composition of steel 17-4PH for special and critical applications is 15-17% Cr, 3.0-5.0% Ni, 3.0-5.0% Cu, 0.07% C (max) and 0.15-0.45% (Nb + Ta) (wt.%). The maximum sulfur content is 0.030%. However, as it will be shown in this work, this maximum limit for sulfur is too high for services where high corrosion resistance is necessary. Two samples of 17-4PH steel with similar base compositions, but quite different sulfur contents (0.027% and 0.001%S), were compared with respect to pitting corrosion and sensitization. Both materials were heat treated according to commercial treatments A, H900, H1100, H1150 and H1150D (ASTM A-1082). Two corrosion tests were applied to compare the steels. The first one was the double-loop electrochemical potentiodynamic reactivation (DL-EPR) test in 0.25 M H2SO4 + 0.01 KSCN solution, which is used to measure the degree of sensitization. The second test was the anodic polarization in 3.5%NaCl solution, commonly used to evaluate the pitting corrosion resistance. Detailed microstructural characterization by magnetic measurements, light optical and scanning electron microscopy was performed. As main conclusion, despite that both steels have chemical compositions in accordance with the standards, the steel with higher sulfur was much more susceptible to pitting and sensitization.

A Grid of NLTE Line-blanketed Model Atmospheres of Early B-Type Stars

NASA Astrophysics Data System (ADS)

Lanz, Thierry; Hubeny, Ivan

2007-03-01

We have constructed a comprehensive grid of 1540 metal line-blanketed, NLTE, plane-parallel, hydrostatic model atmospheres for the basic parameters appropriate to early B-type stars. The BSTAR2006 grid considers 16 values of effective temperatures, 15,000 K<=Teff<=30,000 K with 1000 K steps, 13 surface gravities, 1.75<=logg<=4.75 with 0.25 dex steps, six chemical compositions, and a microturbulent velocity of 2 km s-1. The lower limit of logg for a given effective temperature is set by an approximate location of the Eddington limit. The selected chemical compositions range from twice to one-tenth of the solar metallicity and metal-free. Additional model atmospheres for B supergiants (logg<=3.0) have been calculated with a higher microturbulent velocity (10 km s-1) and a surface composition that is enriched in helium and nitrogen and depleted in carbon. This new grid complements our earlier OSTAR2002 grid of O-type stars (our Paper I). The paper contains a description of the BSTAR2006 grid and some illustrative examples and comparisons. NLTE ionization fractions, bolometric corrections, radiative accelerations, and effective gravities are obtained over the parameter range covered by the grid. By extrapolating radiative accelerations, we have determined an improved estimate of the Eddington limit in absence of rotation between 55,000 and 15,000 K. The complete BSTAR2006 grid is available at the TLUSTY Web site.

Rethinking In Vitro Embryo Culture: New Developments in Culture Platforms and Potential to Improve Assisted Reproductive Technologies1

PubMed Central

Smith, Gary D.; Takayama, Shuichi; Swain, Jason E.

2011-01-01

ABSTRACT The preponderance of research toward improving embryo development in vitro has focused on manipulation of the chemical soluble environment, including altering basic salt composition, energy substrate concentration, amino acid makeup, and the effect of various growth factors or addition or subtraction of other supplements. In contrast, relatively little work has been done examining the physical requirements of preimplantation embryos and the role culture platforms or devices can play in influencing embryo development within the laboratory. The goal of this review is not to reevaluate the soluble composition of past and current embryo culture media, but rather to consider how other controlled and precise factors such as time, space, mechanical interactions, gradient diffusions, cell movement, and surface interactions might influence embryo development. Novel culture platforms are being developed as a result of interdisciplinary collaborations between biologists and biomedical, material, chemical, and mechanical engineers. These approaches are looking beyond the soluble media composition and examining issues such as media volume and embryo spacing. Furthermore, methods that permit precise and regulated dynamic embryo culture with fluid flow and embryo movement are now available, and novel culture surfaces are being developed and tested. While several factors remain to be investigated to optimize the efficiency of embryo production, manipulation of the embryo culture microenvironment through novel devices and platforms may offer a pathway toward improving embryo development within the laboratory of the future. PMID:21998170

Variability of chemical analysis of reinforcing bar produced in Saudi Arabia

NASA Astrophysics Data System (ADS)

Salman, A.; Djavanroodi, F.

2018-04-01

In view of the importance and demanding roles of steel rebar’s in the reinforced concrete structures, accurate information on the properties of the steels is important at the design stage. In the steelmaking process, production variations in chemical composition are unavoidable. The aim of this work is to study the variability of the chemical composition of reinforcing steel produced throughout the Saudi Arabia and asses the quality of steel rebar’s acoording to ASTM A615. 68 samples of ASTM A615 Grade 60 from different manufacturers were collected and tested using the Spectrometer test to obtain Chemical Compositions. EasyFit (5.6) software is utilized to conducted statistical analysis. Chemical compositions distributions and, control charts are generated for the compositions. Results showed that some compositions are above the upper line of the control chart. Finally, the analyses show that less than 3% of the steel failed to meet minimum ASTM standards for chemical composition.

Beginning to Teach Chemistry: How Personal and Academic Characteristics of Pre-Service Science Teachers Compare with Their Understandings of Basic Chemical Ideas

ERIC Educational Resources Information Center

Kind, Vanessa; Kind, Per Morten

2011-01-01

Around 150 pre-service science teachers (PSTs) participated in a study comparing academic and personal characteristics with their misconceptions about basic chemical ideas taught to 11-16-year-olds, such as particle theory, change of state, conservation of mass, chemical bonding, mole calculations, and combustion reactions. Data, collected by…

Brewer's spent grain: a valuable feedstock for industrial applications.

PubMed

Mussatto, Solange I

2014-05-01

Brewer's spent grain (BSG) is the most abundant by-product generated from the beer-brewing process, representing approximately 85% of the total by-products obtained. This material is basically constituted by the barley grain husks obtained as solid residue after the wort production. Since BSG is rich in sugars and proteins, the main and quickest alternative for elimination of this industrial by-product has been as animal feed. However, BSG is a raw material of interest for application in different areas because of its low cost, large availability throughout the year and valuable chemical composition. In the last decade, many efforts have been directed towards the reuse of BSG, taking into account the incentive that has been given to recycle the wastes and by-products generated by industrial activities. Currently, many interesting and advantageous methods for application of BSG in foods, in energy production and in chemical and biotechnological processes have been reported. The present study presents and discusses the most recent perspectives for BSG application in such areas. © 2013 Society of Chemical Industry.

Simultaneous Conoscopic Holography and Raman Spectroscopy

NASA Technical Reports Server (NTRS)

Schramm, Harry F.; Kaiser, Bruce

2005-01-01

A new instrument was developed for chemical characterization of surfaces that combines the analytical power of Raman spectroscopy with the three-dimensional topographic information provided by conoscopic holography. The figure schematically depicts the proposed hybrid instrument. The output of the conoscopic holographic portion of the instrument is a topographical map of the surface; the output of the Raman portion of the instrument is hyperspectral Raman data, from which the chemical and/or biological composition of the surface would be deduced. By virtue of the basic principles of design and operation of the instrument, the hyperspectral image data would be inherently spatially registered with the topographical data. In conoscopic holography, the object and reference beams of classical holography are replaced by the ordinary and extraordinary components generated by a single beam traveling through a birefringent, uniaxial crystal. In the basic conoscopic configuration, a laser light is projected onto a specimen and the resulting illuminated spot becomes a point source of diffuse light that propagates in every direction. The laser beam is rasterscanned in two dimensions (x and y) perpendicular to the beam axis (z), and at each x,y location, the pattern of interference between the ordinary and extraordinary rays is recorded. The recorded interferogram constitutes the conoscopic hologram. Of particular significance for the proposed instrument is that the conoscopic hologram contains information on the z coordinate (height) of the illuminated surface spot. Hence, a topographical map of the specimen is constructed point-by-point by rastering the laser beam in the x and y directions and correlating the x and y coordinates with the z information obtained from the interferograms. Conoscopic imaging is an established method, and conoscopic laboratory instruments for surface metrology are commercially available. In Raman spectroscopy of a surface, one measures the spectrum of laser light scattered inelastically from a laser-illuminated spot on the surface. The wavelengths of the inelastically scattered light differ from that of the incident laser beam by amounts that correspond to the energies of molecular vibrations. The resulting vibrational spectrum can be used to identify the molecules. Raman spectroscopy is a standard laboratory technique for identifying mineralogical, biological, and other specific chemical compositions.

Composite structural materials

NASA Technical Reports Server (NTRS)

Loewy, R.; Wiberley, S. E.

1986-01-01

Overall emphasis is on basic long-term research in the following categories: constituent materials, composite materials, generic structural elements, processing science technology; and maintaining long-term structural integrity. Research in basic composition, characteristics, and processing science of composite materials and their constituents is balanced against the mechanics, conceptual design, fabrication, and testing of generic structural elements typical of aerospace vehicles so as to encourage the discovery of unusual solutions to present and future problems. Detailed descriptions of the progress achieved in the various component parts of this comprehensive program are presented.

[Study on infrared spectrum change of Ganoderma lucidum and its extracts].

PubMed

Chen, Zao-Xin; Xu, Yong-Qun; Chen, Xiao-Kang; Huang, Dong-Lan; Lu, Wen-Guan

2013-05-01

From the determination of the infrared spectra of four substances (original ganoderma lucidum and ganoderma lucidum water extract, 95% ethanol extract and petroleum ether extract), it was found that the infrared spectrum can carry systematic chemical information and basically reflects the distribution of each component of the analyte. Ganoderma lucidum and its extracts can be distinguished according to the absorption peak area ratio of 3 416-3 279, 1 541 and 723 cm(-1) to 2 935-2 852 cm(-1). A method of calculating the information entropy of the sample set with Euclidean distance was proposed, the relationship between the information entropy and the amount of chemical information carried by the sample set was discussed, and the authors come to a conclusion that sample set of original ganoderma lucidum carry the most abundant chemical information. The infrared spectrum set of original ganoderma lucidum has better clustering effect on ganoderma atrum, Cyan ganoderma, ganoderma multiplicatum and ganoderma lucidum when making hierarchical cluster analysis of 4 sample set. The results show that infrared spectrum carries the chemical information of the material structure and closely relates to the chemical composition of the system. The higher the value of information entropy, the much richer the chemical information and the more the benefit for pattern recognition. This study has a guidance function to the construction of the sample set in pattern recognition.

Petrogensis of rhyolitic domes of Dastjerd (SE Qom)

NASA Astrophysics Data System (ADS)

Askari, Nasim; Kheirkhah, Monireh; Hashem Emami, Mohamad

2010-05-01

The study area is located in South Eastern Qom; this area is marginal part of SW Central Iran, located in Urumieh- Dokhtar magmatic belt. Rhyolitic domes (Post Eocene) as endogenous (crypto dome) are along Meyem slip-fault, that this fault probably is effective in emplacement and magma ascent. The ryholitic rocks contain some phenocrysts of garnets, plagioclases and biotits. The groundmasses are consisting of plagioclase, K-feldspar and quartz. Rhyolitic rocks have calc alkaline trends and base on chemical composition of rhyolite rocks and mica bearing. The source of magma is S-type and per aluminums which belongs to collision environment. It is suggested the role of continental crust in generation rhyolitic rocks. Because of the garnet area is an early crystallizing phase and is only confined to rhyolite, it is inferred that the garnet did not crystallize in more basic magmas and that the rhyolite could not have been derived from a basic magma by crystal fractionation. Keywords: Rhyolitic, slip-fault, collision, S-type, endogenous

Oxidative coupling of methane over supported La{sub 2}O{sub 3} and La-promoted MgO catalysts: Influence of catalyst-support interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhary, V.R.; Mulla, S.A.R.; Uphade, B.S.

1997-06-01

Methane-to-C{sub 2}-hydrocarbon conversion activity and selectivity (or yield) of MgO and La-promoted MgO catalysts in the oxidative coupling of methane and strong basicity of the catalysts are decreased appreciably when these catalysts are deposited on commonly used commercial low surface area porous catalyst carriers containing Al{sub 2}O{sub 3}, SiO{sub 2}, SiC, or ZrO{sub 2} + HfO{sub 2} as the main components. The decrease in the strong basicity and catalytic activity/selectivity or yield is mostly due to strong chemical interactions between the active catalyst component (viz., MgO and La{sub 2}O{sub 3}) and the reactive components of the catalyst support (viz., Al{submore » 2}O{sub 3} and SiO{sub 2}), resulting in the formation of catalytically inactive binary metal oxides on the support surface. However, the influence of support on the activity/selectivity of La{sub 2}O{sub 3} is relatively very small, and also the chemical interactions of La{sub 2}O{sub 3} with the supports (except that containing a high concentration of SiO{sub 2}) are almost absent. The catalyst-support interactions are thus found to be strongly dependent upon the nature (chemical composition) of both catalyst and support. For developing better supported catalysts for the oxidative coupling of methane, supported La{sub 2}O{sub 3} with some promoters shows high promise.« less

An Empirical Determination of Tasks Essential to Successful Performance as a Chemical Applicator. Determination of a Common Core of Basic Skills in Agribusiness and Natural Resources.

ERIC Educational Resources Information Center

Miller, Daniel R.; And Others

To improve vocational educational programs in agriculture, occupational information on a common core of basic skills within the occupational area of the chemical applicator is presented in the revised task inventory survey. The purpose of the occupational survey was to identify a common core of basic skills which are performed and are essential…

Soil-vegetation relationships on a banded ironstone 'island', Carajás Plateau, Brazilian Eastern Amazonia.

PubMed

Nunes, Jaquelina A; Schaefer, Carlos E G R; Ferreira Júnior, Walnir G; Neri, Andreza V; Correa, Guilherme R; Enright, Neal J

2015-01-01

Vegetation and soil properties of an iron-rich canga (laterite) island on the largest outcrop of banded-iron formation in Serra de Carajás (eastern Amazonia, Brazil) were studied along a topographic gradient (738-762 m asl), and analyzed to test the hypothesis that soil chemical and physical attributes play a key role in the structure and floristic composition of these plant communities. Soil and vegetation were sampled in eight replicate plots within each of the four vegetation types. Surface (0-10 cm) soil samples from each plot were analyzed for basic cations, N, P and plant species density for all species was recorded. CCA ordination analysis showed a strong separation between forest and non-forest sites on the first axis, and between herbaceous and shrubby campo rupestre on the second axis. The four vegetation types shared few plant species, which was attributed to their distinctive soil environments and filtering of their constituent species by chemical, physical and hydrological constraints. Thus, we can infer that Edaphic (pedological) factors are crucial in explaining the types and distributions of campo rupestre vegetation associated with ferruginous ironstone uplands (Canga) in Carajás, eastern Amazonia, therefore the soil properties are the main drivers of vegetation composition and structure on these ironstone islands.

Incubation temperature influences trade-off between structural size and energy reserves in mallard hatchlings.

PubMed

Koláčková, Martina; Prokůpková, Ludmila; Albrecht, Tomáš; Hořák, David

2015-01-01

The reproductive success of precocial birds depends on investments in clutch formation and incubation. Egg quality strongly affects the phenotypic traits correlated with survival of the hatchling, but parental ability to maintain incubation temperature can also influence hatchling outcomes. The effect of incubation temperature on hatchling phenotype has been widely studied in reptiles but not in birds. The aim of this study was to explore the effects of egg mass and incubation temperature on the incubation period, hatchability, and hatchling phenotype of the mallard (Anas platyrhynchos). Mallard eggs were incubated under six constant incubation temperatures (ranging from 35.0° to 39.0°C). Hatchlings were weighed, and their structural size was measured. Some hatchlings were used for an examination of residual yolk sac mass and basic chemical composition of the yolk-free body. All investigated phenotypic traits except for chemical composition were positively correlated with egg mass. Incubation temperature did not affect hatchling body mass, but increased temperatures led to a decreased yolk-free body mass and structural size of hatchlings and to increased yolk sac mass. Our results suggest that there is a trade-off between the yolk-free body size and energetic reserves in the form of the yolk sac and that this trade-off is modulated by incubation temperature.

Effects of Ni content on nanocrystalline Fe-Co-Ni ternary alloys synthesized by a chemical reduction method

NASA Astrophysics Data System (ADS)

Chokprasombat, Komkrich; Pinitsoontorn, Supree; Maensiri, Santi

2016-05-01

Magnetic properties of Fe-Co-Ni ternary alloys could be altered by changing of the particle size, elemental compositions, and crystalline structures. In this work, Fe50Co50-xNix nanoparticles (x=10, 20, 40, and 50) were prepared by the novel chemical reduction process. Hydrazine monohydrate was used as a reducing agent under the concentrated basic condition with the presence of poly(vinylpyrrolidone). We found that the nanoparticles were composed of Fe, Co and Ni with compositions according to the molar ratio of the metal sources. Interestingly, the particles were well-crystalline at the as-prepared state without post-annealing at high temperature. Increasing Ni content resulted in phase transformation from body centered cubic (bcc) to face centered cubic (fcc). For the fcc phase, the average particle size decreased when increased the Ni content; the Fe50Ni50 nanoparticles had the smallest average size with the narrowest size distribution. In additions, the particles exhibited ferromagnetic properties at room temperature with the coercivities higher than 300 Oe, and the saturation magnetiation decreased with increasing Ni content. These results suggest that the structural and magnetic properties of Fe-Co-Ni alloys could be adjusted by varying the Ni content.

Characterization of Non-Newtonian Fluids for Environmental Applications

NASA Astrophysics Data System (ADS)

Espinoza, I.; Hauswirth, S.; Cerda, C. C.; Sadeghi, S.

2017-12-01

Non-Newtonian fluids are fluids that exhibit viscosity changes with time, stress, or changing shear rates. This distinctive quality is advantageous to a number of applications, such as hydraulic fracturing and contaminant remediation. The use of non-Newtonian fluids in contaminant remediation has recently increased as a method of improving delivery of chemical oxidants and surfactants in hard-to-reach, low permeability zones within the subsurface. As the application of these fluids continues to increase, a need to improve upon the basic understanding of non-Newtonian fluid rheology becomes increasingly important. This study investigates the characteristics of guar gum and xanthan gum, two common non-Newtonian polymers, and how factors such as composition, preparation method, and chemical and biological degradation impact the rheology of the fluids. Because the polymers are semi-hydrophobic, preparation of solutions requires blending, heating, pre-dissolution in alcohol, addition of surfactant, or stirring for extended time periods. Additionally, fluids are commonly filtered to remove undissolved material and gels, and subsequently stored under a variety of conditions. We investigated the effect of these processes on the fluids' rheology by producing solutions at a range of concentrations with a variety of preparation and storage methods. The rheological properties of the solutions were then measured over a period of months with a rotational rheometer. The experimental data were fit to standard rheological models, and the parameters of these models were used to quantitatively assess the effect of chemical composition, physical processing, and storage on the fluid rheology. The results of this study provide an improved basis with which to predict physical, chemical, and temporal alterations of guar and xanthan gum rheology, and thereby allow for improved design of experimental, modeling, and field applications utilizing non-Newtonian fluids.

The effect of carbon surface chemical composition on the adsorption of acetanilide.

PubMed

Terzyk, Artur P

2004-04-01

The study of acetanilide adsorption-desorption performed at three temperatures (300, 310, and 320 K) and at two pH levels (7.0 and 1.5) on the series of D43/1 carbons (initial and modified with HNO3, fuming H2SO4, and gaseous NH3) is reported. Sorption data are additionally supplemented with the results of thermal analysis and calorimetric and kinetic measurements. It is shown that, generally, acetanilide adsorption at the neutral pH level is reversible (only on the more acidic carbons and at the lowest temperature does hysteresis occur due to the formation of hydrogen bonds with surface OH groups), and it decreases for the chemically modified carbons. In contrast, at the acidic pH level acetanilide adsorption is irreversible. A mechanism of irreversibility is proposed and it is shown that hysteresis is caused by the chemical reaction between the nucleophile (carbon) and the protonized acetanilide molecules. For all studied carbons, at the acidic pH level, adsorption increases and this is caused by the weakly basic character of acetanilide molecule. Adsorption results are described applying adsorbability and Dubinin-Astakhov, quasi-Freundlich and solution analogue of the Toth adsorption isotherm equations. Using the kinetic data, the effective diffusion coefficients and the energy of diffusion are calculated. It is shown that the diffusion is mainly a surface process, and the contribution of the pore diffusion increases with the rise in temperature. By applying different correlations between the parameters obtained from the theoretical description of experimental data and those characterizing the chemical composition of the studied carbons, the role of the latter in the adsorption and kinetics of acetanilide adsorption is determined.

Reasoning the Need: Graduate Education and Basic Writing

ERIC Educational Resources Information Center

Gleason, Barbara

2006-01-01

While college composition theory/pedagogy courses are standard offerings in composition and rhetoric graduate programs, specialized basic writing graduate courses lag behind. At the same time, there is a pressing need for highly qualified teachers of nontraditional adult students, especially in community college and adult literacy education…

Reconciling differences in stratospheric ozone composites

NASA Astrophysics Data System (ADS)

Ball, William T.; Alsing, Justin; Mortlock, Daniel J.; Rozanov, Eugene V.; Tummon, Fiona; Haigh, Joanna D.

2017-10-01

Observations of stratospheric ozone from multiple instruments now span three decades; combining these into composite datasets allows long-term ozone trends to be estimated. Recently, several ozone composites have been published, but trends disagree by latitude and altitude, even between composites built upon the same instrument data. We confirm that the main causes of differences in decadal trend estimates lie in (i) steps in the composite time series when the instrument source data changes and (ii) artificial sub-decadal trends in the underlying instrument data. These artefacts introduce features that can alias with regressors in multiple linear regression (MLR) analysis; both can lead to inaccurate trend estimates. Here, we aim to remove these artefacts using Bayesian methods to infer the underlying ozone time series from a set of composites by building a joint-likelihood function using a Gaussian-mixture density to model outliers introduced by data artefacts, together with a data-driven prior on ozone variability that incorporates knowledge of problems during instrument operation. We apply this Bayesian self-calibration approach to stratospheric ozone in 10° bands from 60° S to 60° N and from 46 to 1 hPa (˜ 21-48 km) for 1985-2012. There are two main outcomes: (i) we independently identify and confirm many of the data problems previously identified, but which remain unaccounted for in existing composites; (ii) we construct an ozone composite, with uncertainties, that is free from most of these problems - we call this the BAyeSian Integrated and Consolidated (BASIC) composite. To analyse the new BASIC composite, we use dynamical linear modelling (DLM), which provides a more robust estimate of long-term changes through Bayesian inference than MLR. BASIC and DLM, together, provide a step forward in improving estimates of decadal trends. Our results indicate a significant recovery of ozone since 1998 in the upper stratosphere, of both northern and southern midlatitudes, in all four composites analysed, and particularly in the BASIC composite. The BASIC results also show no hemispheric difference in the recovery at midlatitudes, in contrast to an apparent feature that is present, but not consistent, in the four composites. Our overall conclusion is that it is possible to effectively combine different ozone composites and account for artefacts and drifts, and that this leads to a clear and significant result that upper stratospheric ozone levels have increased since 1998, following an earlier decline.

Single Particle Analysis by Combined Chemical Imaging to Study Episodic Air Pollution Events in Vienna

NASA Astrophysics Data System (ADS)

Ofner, Johannes; Eitenberger, Elisabeth; Friedbacher, Gernot; Brenner, Florian; Hutter, Herbert; Schauer, Gerhard; Kistler, Magdalena; Greilinger, Marion; Lohninger, Hans; Lendl, Bernhard; Kasper-Giebl, Anne

2017-04-01

The aerosol composition of a city like Vienna is characterized by a complex interaction of local emissions and atmospheric input on a regional and continental scale. The identification of major aerosol constituents for basic source appointment and air quality issues needs a high analytical effort. Exceptional episodic air pollution events strongly change the typical aerosol composition of a city like Vienna on a time-scale of few hours to several days. Analyzing the chemistry of particulate matter from these events is often hampered by the sampling time and related sample amount necessary to apply the full range of bulk analytical methods needed for chemical characterization. Additionally, morphological and single particle features are hardly accessible. Chemical Imaging evolved to a powerful tool for image-based chemical analysis of complex samples. As a complementary technique to bulk analytical methods, chemical imaging can address a new access to study air pollution events by obtaining major aerosol constituents with single particle features at high temporal resolutions and small sample volumes. The analysis of the chemical imaging datasets is assisted by multivariate statistics with the benefit of image-based chemical structure determination for direct aerosol source appointment. A novel approach in chemical imaging is combined chemical imaging or so-called multisensor hyperspectral imaging, involving elemental imaging (electron microscopy-based energy dispersive X-ray imaging), vibrational imaging (Raman micro-spectroscopy) and mass spectrometric imaging (Time-of-Flight Secondary Ion Mass Spectrometry) with subsequent combined multivariate analytics. Combined chemical imaging of precipitated aerosol particles will be demonstrated by the following examples of air pollution events in Vienna: Exceptional episodic events like the transformation of Saharan dust by the impact of the city of Vienna will be discussed and compared to samples obtained at a high alpine background site (Sonnblick Observatory, Saharan Dust Event from April 2016). Further, chemical imaging of biological aerosol constituents of an autumnal pollen breakout in Vienna, with background samples from nearby locations from November 2016 will demonstrate the advantages of the chemical imaging approach. Additionally, the chemical fingerprint of an exceptional air pollution event from a local emission source, caused by the pull down process of a building in Vienna will unravel the needs for multisensor imaging, especially the combinational access. Obtained chemical images will be correlated to bulk analytical results. Benefits of the overall methodical access by combining bulk analytics and combined chemical imaging of exceptional episodic air pollution events will be discussed.

Environmental and Chemical Aging of Fatty-Acid-Based Vinyl Ester Composites

DTIC Science & Technology

2011-04-01

Environmental and Chemical Aging of Fatty- Acid -Based Vinyl Ester Composites by Steven E. Boyd and John J. La Scala ARL-TR-5523 April...2011 Environmental and Chemical Aging of Fatty- Acid -Based Vinyl Ester Composites Steven E. Boyd and John J. La Scala Weapons and Materials...COVERED (From - To) October 2009–September 2010 4. TITLE AND SUBTITLE Environmental and Chemical Aging of Fatty- Acid -Based Vinyl Ester Composites

High Temperature Degradation Mechanisms in Polymer Matrix Composites

NASA Technical Reports Server (NTRS)

Cunningham, Ronan A.

1996-01-01

Polymer matrix composites are increasingly used in demanding structural applications in which they may be exposed to harsh environments. The durability of such materials is a major concern, potentially limiting both the integrity of the structures and their useful lifetimes. The goal of the current investigation is to develop a mechanism-based model of the chemical degradation which occurs, such that given the external chemical environment and temperatures throughout the laminate, laminate geometry, and ply and/or constituent material properties, we can calculate the concentration of diffusing substances and extent of chemical degradation as functions of time and position throughout the laminate. This objective is met through the development and use of analytical models, coupled to an analysis-driven experimental program which offers both quantitative and qualitative information on the degradation mechanism. Preliminary analyses using a coupled diffusion/reaction model are used to gain insight into the physics of the degradation mechanisms and to identify crucial material parameters. An experimental program is defined based on the results of the preliminary analysis which allows the determination of the necessary material coefficients. Thermogravimetric analyses are carried out in nitrogen, air, and oxygen to provide quantitative information on thermal and oxidative reactions. Powdered samples are used to eliminate diffusion effects. Tests in both inert and oxidative environments allow the separation of thermal and oxidative contributions to specimen mass loss. The concentration dependency of the oxidative reactions is determined from the tests in pure oxygen. Short term isothermal tests at different temperatures are carried out on neat resin and unidirectional macroscopic specimens to identify diffusion effects. Mass loss, specimen shrinkage, the formation of degraded surface layers and surface cracking are recorded as functions of exposure time. Geometry effects in the neat resin, and anisotropic diffusion effects in the composites, are identified through the use of specimens with different aspect ratios. The data is used with the model to determine reaction coefficients and effective diffusion coefficients. The empirical and analytical correlations confirm the preliminary model results which suggest that mass loss at lower temperatures is dominated by oxidative reactions and that these reaction are limited by diffusion of oxygen from the surface. The mechanism-based model is able to successfully capture the basic physics of the degradation phenomena under a wide range of test conditions. The analysis-based test design is successful in separating out oxidative, thermal, and diffusion effects to allow the determination of material coefficients. This success confirms the basic picture of the process; however, a more complete understanding of some aspects of the physics are required before truly predictive capability can be achieved.

Vector diagram of the chemical compositions of tektites and earth lavas

NASA Technical Reports Server (NTRS)

Kvasha, L. G.; Gorshkov, G. S.

1978-01-01

The chemical compositions of tektites and various volcanic glasses, similar in composition to tektites are compared by a petrochemical method. The advantage of the method is that a large number of chemical analyses of igneous rocks can be graphically compared with the help of vectors, plotted in relation to six parameters. These parameters, calculated from ratios of the main oxides given by silicate analysis, reflect the chief characteristics of igneous rock. Material for the study was suppled by data from chemical analysis characterizing tektites of all known locations and data from chemical analyses of obsidians similar in chemical composition to tektites of various petrographical provinces.

Histochemical investigation of Cochlospermum regium (Schrank) Pilg. leaves and chemical composition of its essential oil.

PubMed

Inácio, Marielle Cascaes; Paz, Tiago Antunes; Bertoni, Bianca Waléria; Vieira, Maria Aparecida Ribeiro; Marques, Márcia Ortiz Mayo; Pereira, Ana Maria Soares

2014-01-01

Essential oil from Cochlospermum regium (Schrank) Pilg. leaves (CR-EO) has been extracted by hydrodistillation; we analysed the CR-EO by gas chromatography coupled with mass spectrometry. We also conducted histochemical analysis on cross-sections of the central vein of young and adult leaves. A total of 32 compounds were qualitatively and quantitatively analysed, which represented 94.87% of the total CR-EO oil content. The CR-EO basically consisted of sesquiterpenes (96.87%); its main component was β-copaen-4-α-ol (18.73%), followed by viridiflorol (12.67%). The histochemical analyses identified the main classes of compounds present in both young and adult leaves.

Distribution of Stress in Deformation Zone of Niobium Microalloyed Steel

NASA Astrophysics Data System (ADS)

Jandrlić, Ivan; Rešković, Stoja; Brlić, Tin

2018-03-01

Microalloyed steels today represent a significant part of total world production and processing of steel. Although widely used, there are scarce data on the stress distribution in the deformation zone of these steels. Research was carried out on two steel grades, both low-carbon structural steels with the same basic chemical composition, with one of them additionally microalloyed with niobium. Differences in the stress distribution in the deformation zone between two tested steels were continuously observed and measured using the methods of digital image correlation and thermography. It has been found out that niobium microalloyed steel has significantly more complex material flow and stress distribution in the deformation zone when compared to the plain low carbon steel.

Distribution of Stress in Deformation Zone of Niobium Microalloyed Steel

NASA Astrophysics Data System (ADS)

Jandrlić, Ivan; Rešković, Stoja; Brlić, Tin

2018-07-01

Microalloyed steels today represent a significant part of total world production and processing of steel. Although widely used, there are scarce data on the stress distribution in the deformation zone of these steels. Research was carried out on two steel grades, both low-carbon structural steels with the same basic chemical composition, with one of them additionally microalloyed with niobium. Differences in the stress distribution in the deformation zone between two tested steels were continuously observed and measured using the methods of digital image correlation and thermography. It has been found out that niobium microalloyed steel has significantly more complex material flow and stress distribution in the deformation zone when compared to the plain low carbon steel.

The physiological basics of the olfactory neuro-epithelium.

PubMed

Watelet, J B; Katotomichelakis, M; Eloy, P; Danielidis, V

2009-01-01

All living organisms can detect and identify chemical substances in their environment. The olfactory epithelium is covered by a mucus layer which is essential for the function of the olfactory neurons that are directly connected to the brain through the cribriform plate. However, little is known about the composition of this mucus in humans and its significance for the diagnosis of olfactory disorders. The olfactory epithelium consists of four primary cell types, including the olfactory receptor cells essential for odour transduction. This review examines the anatomical, histological and physiological fundamentals of olfactory mucosa. Particular attention is paid to the biochemical environment of the olfactory mucosa that regulates both peri-receptor events and several protective functions.

Additive effects due to biochar and endophyte application enable soybean to enhance nutrient uptake and modulate nutritional parameters* #

PubMed Central

Waqas, Muhammad; Kim, Yoon-Ha; Khan, Abdul Latif; Shahzad, Raheem; Asaf, Sajjad; Hamayun, Muhammad; Kang, Sang-Mo; Khan, Muhammad Aaqil; Lee, In-Jung

2017-01-01

We studied the effects of hardwood-derived biochar (BC) and the phytohormone-producing endophyte Galactomyces geotrichum WLL1 in soybean (Glycine max (L.) Merr.) with respect to basic, macro-and micronutrient uptakes and assimilations, and their subsequent effects on the regulation of functional amino acids, isoflavones, fatty acid composition, total sugar contents, total phenolic contents, and 1,1-diphenyl-2-picrylhydrazyl (DPPH)-scavenging activity. The assimilation of basic nutrients such as nitrogen was up-regulated, leaving carbon, oxygen, and hydrogen unaffected in BC+G. geotrichum-treated soybean plants. In comparison, the uptakes of macro-and micronutrients fluctuated in the individual or co-application of BC and G. geotrichum in soybean plant organs and rhizospheric substrate. Moreover, the same attribute was recorded for the regulation of functional amino acids, isoflavones, fatty acid composition, total sugar contents, total phenolic contents, and DPPH-scavenging activity. Collectively, these results showed that BC+G. geotrichum-treated soybean yielded better results than did the plants treated with individual applications. It was concluded that BC is an additional nutriment source and that the G. geotrichum acts as a plant biostimulating source and the effects of both are additive towards plant growth promotion. Strategies involving the incorporation of BC and endophytic symbiosis may help achieve eco-friendly agricultural production, thus reducing the excessive use of chemical agents. PMID:28124840

Surface chemical composition of human maxillary first premolar as assessed by X-ray photoelectron spectroscopy (XPS)

NASA Astrophysics Data System (ADS)

Lou, Leo; Nelson, Alan E.; Heo, Giseon; Major, Paul W.

2008-08-01

The surface chemical composition of dental enamel has been postulated as a contributing factor in the variation of bond strength of brackets bonded to teeth, and hence, the probability of bracket failure during orthodontic treatment. This study systematically investigated the chemical composition of 98 bonding surfaces of human maxillary premolars using X-ray photoelectron spectroscopy (XPS) to ascertain compositional differences between right and left first premolars. The major elements detected in all samples were calcium, phosphorus, oxygen, nitrogen and carbon. Surface compositions were highly variable between samples and several elements were found to be highly correlated. No statistical significant difference in the chemical composition of the maxillary right and left first premolars was found ( p > 0.05). Knowledge of the chemical composition of enamel surfaces will facilitate future studies that relate this information to the variations in dental enamel bond strength.

Petrogenesis and tectonic association of rift-related basic Panjal dykes from the northern Indian plate, North-Western Pakistan: evidence of high-Ti basalts analogous to dykes from Tibet

NASA Astrophysics Data System (ADS)

Sajid, Muhammad; Andersen, Jens; Arif, Mohammad

2017-10-01

Rift related magmatism during Permian time in the northern margin of Indian plate is represented by basic dykes in several Himalayan terranes including north western Pakistan. The field relations, mineralogy and whole rock geochemistry of these basic dykes reveal significant textural, mineralogical and chemical variation between two major types (a) dolerite and (b) amphibolite. Intra-plate tectonic settings for both rock types have been interpreted on the basis of low Zr/Nb ratios (< 10), K/Ba ratios (20-40) and Hf-Ta-Th and FeO-MgO-Al2O3 discrimination diagrams. The compositional zoning in plagioclase and clinopyroxene, variation in olivine compositions and major elements oxide trends indicate a vital role of fractional crystallization in the evolution of dolerites, which also show depletion in rare earth elements (REEs) and other incompatible elements compared to the amphibolites. The equilibrium partial melting models from primitive mantle using Dy/Yb, La/Yb, Sm/Yb and La/Sm ratios show that amphibolite formed by smaller degrees (< 5%) of partial melting than the dolerites (< 10%). The trace elements ratios suggest the origination of dolerites from the subcontinental lithospheric mantle with some crustal contamination. This is consistent with a petrogenetic relationship with Panjal trap magmatism, reported from Kashmir and other parts of north western India. The amphibolites, in contrast, show affinity towards Ocean Island basalts (OIB) with a relatively deep asthenospheric mantle source and minimal crustal contribution and are geochemically similar to the High-Ti mafic dykes of southern Qiangtang, Tibet. These similarities combined with Permian tectonic restoration of Gondwana indicate the coeval origin for both dykes from distinct mantle source during continental rifting related to formation of the Neotethys Ocean.

Petrogenesis and tectonic association of rift-related basic Panjal dykes from the northern Indian plate, North-Western Pakistan: evidence of high-Ti basalts analogous to dykes from Tibet

NASA Astrophysics Data System (ADS)

Sajid, Muhammad; Andersen, Jens; Arif, Mohammad

2018-06-01

Rift related magmatism during Permian time in the northern margin of Indian plate is represented by basic dykes in several Himalayan terranes including north western Pakistan. The field relations, mineralogy and whole rock geochemistry of these basic dykes reveal significant textural, mineralogical and chemical variation between two major types (a) dolerite and (b) amphibolite. Intra-plate tectonic settings for both rock types have been interpreted on the basis of low Zr/Nb ratios (< 10), K/Ba ratios (20-40) and Hf-Ta-Th and FeO-MgO-Al2O3 discrimination diagrams. The compositional zoning in plagioclase and clinopyroxene, variation in olivine compositions and major elements oxide trends indicate a vital role of fractional crystallization in the evolution of dolerites, which also show depletion in rare earth elements (REEs) and other incompatible elements compared to the amphibolites. The equilibrium partial melting models from primitive mantle using Dy/Yb, La/Yb, Sm/Yb and La/Sm ratios show that amphibolite formed by smaller degrees (< 5%) of partial melting than the dolerites (< 10%). The trace elements ratios suggest the origination of dolerites from the subcontinental lithospheric mantle with some crustal contamination. This is consistent with a petrogenetic relationship with Panjal trap magmatism, reported from Kashmir and other parts of north western India. The amphibolites, in contrast, show affinity towards Ocean Island basalts (OIB) with a relatively deep asthenospheric mantle source and minimal crustal contribution and are geochemically similar to the High-Ti mafic dykes of southern Qiangtang, Tibet. These similarities combined with Permian tectonic restoration of Gondwana indicate the coeval origin for both dykes from distinct mantle source during continental rifting related to formation of the Neotethys Ocean.

Geochemistry and shock petrography of the Crow Creek Member, South Dakota, USA: Ejecta from the 74-Ma Manson impact structure

USGS Publications Warehouse

Katongo, C.; Koeberl, C.; Witzke, B.J.; Hammond, R.H.; Anderson, R.R.

2004-01-01

The Crow Creek Member is one of several marl units recognized within the Upper Cretaceous Pierre Shale Formation of eastern South Dakota and northeastern Nebraska, but it is the only unit that contains shock-metamorphosed minerals. The shocked minerals represent impact ejecta from the 74-Ma Manson impact structure (MIS). This study was aimed at determining the bulk chemical compositions and analysis of planar deformation features (PDFs) of shocked quartz; for the basal and marly units of the Crow Creek Member. We studied samples from the Gregory 84-21 core, Iroquois core and Wakonda lime quarry. Contents of siderophile elements are generally high, but due to uncertainties in the determination of Ir and uncertainties in compositional sources for Cr, Co, and Ni, we could not confirm an extraterrestrial component in the Crow Creek Member. We recovered several shocked quartz grains from basal-unit samples, mainly from the Gregory 84-21 core, and results of PDF measurements indicate shock pressures of at least 15 GPa. All the samples are composed chiefly of SiO2, (29-58 wt%), Al2O3 (6-14 wt%), and CaO (7-30 wt%). When compared to the composition of North American Shale Composite, the samples are significantly enriched in CaO, P2O5, Mn, Sr, Y, U, Cr, and Ni. The contents of rare earth elements (REE), high field strength elements (HFSE), Cr, Co, Sc, and their ratios and chemical weathering trends, reflect both felsic and basic sources for the Crow Creek Member, an inference, which is consistent with the lithological compositions in the environs of the MIS. The high chemical indices of alteration and weathering (CIA' and CIW': 75-99), coupled with the Al2O3-(CaO*,+Na2O -K2O (A-CN'-K) ratios, indicate that the Crow Creek Member and source rocks had undergone high degrees of chemical weathering. The expected ejecta thicknesses at the sampled locations (409 to 219 km from Manson) were calculated to range from about 1.9 to 12.2 cm (for the present-day crater radius of Manson), or 0.4 to 2.4 cm (for the estimated transient cavity radius). The trend agrees with the observed thicknesses of the basal unit of the Crow Creek Member, but the actually observed thicknesses are larger than the calculated ones, indicating that not all of the basal unit comprises impact ejecta. ?? Meteoritical Society, 2004.

An isotopic study of mafic microgranular enclaves in the Katsuragi adakitic tonalite, southwestern Japan.

NASA Astrophysics Data System (ADS)

Tezuka, N.; Tsuboi, M.; Asahara, Y.

2017-12-01

The Cretaceous Katsuragi tonalite in southwestern Japan has been regarded as adakite formed by the partial melting of lower crust a) b). The tonalite is 10 x 15 km in areal extent, is composed of hornblende-biotite tonalite with a mineral assemblage of plagioclase, biotite, quartz and hornblende, and contains mafic microgranular enclaves (MME). The MME has dioritic composition with a mineral assemblage of plagioclase, biotite, hornblende and quartz. The boundary between the tonalite and the MME is sharp. To reveal the relationship between the MME and adakitic feature of the host tonalite, we have focused on the chemical and Sr-Nd isotopic compositions of the MME in the Katsuragi tonalite. Three models have been proposed for the origin of MME: restite, magma-mixing, and cumulate c). In the restite model, MME is regarded as a residual material of partial melting, and therefore chemical compositions of MME and host should show a linear trend on the Harker's diagram. However, the Katsuragi tonalite and its MME do not show one linear trend. Based on mixing of two magmas, initial 87Sr/86Sr (SrI) value of MME is basically different from that of its host. However, the SrI value of the MME is 0.70725-0.70749 and is identical to the value of 0.70728 in the Katsuragi tonalite d), indicating one magma source for the MME and its host. According to the cumulate model, MME forms from cumulate piles by subsequent feeding of congenetic magma immediately after the early crystallized minerals are solidified. The concordance of the age and SrI between the Katsuragi tonalite and its MME strongly indicate the cumulate origin c). Furthermore, the mineral assemblage of the MME resembles with the common mineral assemblage of andesitic cumulate such as plagioclase, hornblende and quartz c), and this is consistent with the cumulate model. Based on the cumulate origin of the MME, the adakitic feature of chemical composition in the host rock is potentially formed by the separation of cumulate. In the presentation, we evaluate the adakitic, chemical composition of the Katsuragi tonalite by calculation of MME separation from parental magma. a) K. Takemura, M. Tsuboi, 2014, MAGMA, 96, 31, 44. b) Y. Nishioka, 2008, 115th Ann. Meet. Geol. Soc. Japan, Abstr., 131.c) S. Chen et al., 2016, Lithos, 248, 251, 455, 468. d) K. Morioka et al., 2000, Island Arc, 9, 46, 54.

Composition and Chemical Stability of Motor Fuels,

DTIC Science & Technology

Fuels, *Hydrocarbons, Cycloalkanes, Chemical analysis, Gasoline, Diesel fuels, Fuel additives, Chemical reactions, Stability, Jet engine fuels...Aviation gasoline, Aviation fuels, Chemical composition, Aromatic hydrocarbons, Unsaturated hydrocarbons, Storage, USSR, Translations, Fuel systems, Alkanes

The Influence of Sizings on the Durability of High-Temperature Polymer Composites

NASA Technical Reports Server (NTRS)

Allred, Ronald E.; Wesson, Sheldon P.; Shin, E. Eugene; Inghram, Linda; McCorkle, Linda; Papadopoulos, Demetrios; Wheeler, Donald; Sutter, James K.

2004-01-01

To increase performance and durability of high-temperature composites for potential rocket engine components, it is necessary to optimize wetting and interfacial bonding between high modulus carbon fibers and high-temperature polyimide resins. Sizings commercially supplied on most carbon fibers are not compatible with polyimides. In this study, the chemistry of sizings on two high-modulus carbon fibers (M40J and M60J, Toray) was characterized as was the chemistry of PMR-II-50 fluorinated polyimide resin. The carbon fibers were characterized using single filament wetting, scanning electron microscopy, fourier transform infrared spectroscopy, and x-ray photoelectron spectroscopic measurements. The polyimide matrix resins were coated onto glass filaments for characterization by wetting measurements. Surface energy components were obtained by wetting with nondispersive (methylene iodide), acidic (ethylene glycol), and basic (formamide) probes. A continuous desizing system that uses an environmentally friendly chemical-mechanical process was developed for tow level fiber. Composites were fabricated with fibers containing the manufacturer's sizing, desized, and further treated with a reactive finish. Results of room-temperature tests after thermal aging show that the reactive finish produces a higher strength and more durable interface compared to the manufacturer's sizing. When exposed to moisture blistering tests, however, the better bonded composite displayed a tendency to delaminate, presumably due to trapping of volatiles.

Plant Species Rather Than Climate Greatly Alters the Temporal Pattern of Litter Chemical Composition During Long-Term Decomposition

NASA Astrophysics Data System (ADS)

Li, Yongfu; Chen, Na; Harmon, Mark E.; Li, Yuan; Cao, Xiaoyan; Chappell, Mark A.; Mao, Jingdong

2015-10-01

A feedback between decomposition and litter chemical composition occurs with decomposition altering composition that in turn influences the decomposition rate. Elucidating the temporal pattern of chemical composition is vital to understand this feedback, but the effects of plant species and climate on chemical changes remain poorly understood, especially over multiple years. In a 10-year decomposition experiment with litter of four species (Acer saccharum, Drypetes glauca, Pinus resinosa, and Thuja plicata) from four sites that range from the arctic to tropics, we determined the abundance of 11 litter chemical constituents that were grouped into waxes, carbohydrates, lignin/tannins, and proteins/peptides using advanced 13C solid-state NMR techniques. Decomposition generally led to an enrichment of waxes and a depletion of carbohydrates, whereas the changes of other chemical constituents were inconsistent. Inconsistent convergence in chemical compositions during decomposition was observed among different litter species across a range of site conditions, whereas one litter species converged under different climate conditions. Our data clearly demonstrate that plant species rather than climate greatly alters the temporal pattern of litter chemical composition, suggesting the decomposition-chemistry feedback varies among different plant species.

Plant Species Rather Than Climate Greatly Alters the Temporal Pattern of Litter Chemical Composition During Long-Term Decomposition

PubMed Central

Li, Yongfu; Chen, Na; Harmon, Mark E.; Li, Yuan; Cao, Xiaoyan; Chappell, Mark A.; Mao, Jingdong

2015-01-01

A feedback between decomposition and litter chemical composition occurs with decomposition altering composition that in turn influences the decomposition rate. Elucidating the temporal pattern of chemical composition is vital to understand this feedback, but the effects of plant species and climate on chemical changes remain poorly understood, especially over multiple years. In a 10-year decomposition experiment with litter of four species (Acer saccharum, Drypetes glauca, Pinus resinosa, and Thuja plicata) from four sites that range from the arctic to tropics, we determined the abundance of 11 litter chemical constituents that were grouped into waxes, carbohydrates, lignin/tannins, and proteins/peptides using advanced 13C solid-state NMR techniques. Decomposition generally led to an enrichment of waxes and a depletion of carbohydrates, whereas the changes of other chemical constituents were inconsistent. Inconsistent convergence in chemical compositions during decomposition was observed among different litter species across a range of site conditions, whereas one litter species converged under different climate conditions. Our data clearly demonstrate that plant species rather than climate greatly alters the temporal pattern of litter chemical composition, suggesting the decomposition-chemistry feedback varies among different plant species. PMID:26515033

Stand Up and Write: Completing the Freshman Communications Course.

ERIC Educational Resources Information Center

Goldstein, Richard M.; Nelson, Charles W.

Members of the English and speech faculty at Michigan Technological University combined and coordinated their ideas to find a way to introduce the basics of oral communication into the composition course. The course itself is structured according to the quarter system, in which basic composition is taught in the first term, research methods and…

Research and Practice on Basic Composition and Cultivation Pattern of College Students' Innovative Ability

ERIC Educational Resources Information Center

Xu, Zhenhui; Chen, Hanlin

2010-01-01

Facing the increasingly fierce international competition, it has been the core of higher education to explore how to cultivate college students with innovative ability. College students' innovative ability is mainly composed of basic ability, innovative thinking and innovative actions. In conformity to the above composition, the cultivation…

A chemical model for lunar non-mare rocks

NASA Technical Reports Server (NTRS)

Hubbard, N. J.; Rhodes, J. M.

1974-01-01

Nearly all rocks returned from the moon are readily divided into three broad categories on the basis of their chemical compositions: (1) mare basalts, (2) non-mare rocks of basaltic composition (KREEP, VHA), and (3) anorthositic rocks. Only mare basalts may unambiguously be considered to have original igneous textures and are widely understood to have an igneous origin. Nearly all other lunar rocks have lost their original textures during metamorphic and impact processes. It is shown that for these rocks one must work primarily with chemical data in order to recognize and define rock groups and their possible modes of origin. Non-mare rocks of basaltic composition have chemical compositions consistent with an origin by partial melting of the lunar interior. The simplest origin for rocks of anorthositic chemical composition is the crystallization and removal of ferromagnesian minerals. It is proposed that the rock groups of anorthositic and non-mare basaltic chemical composition could have been generated from a single series of original but not necessarily primitive lunar materials.

Polypyrrole-MWCNT-Ag composites for electromagnetic shielding: Comparison between chemical deposition and UV-reduction approaches

NASA Astrophysics Data System (ADS)

Ebrahimi, Izadyar; Gashti, Mazeyar Parvinzadeh

2018-07-01

In this study, we focused on the synthesis of polypyrrole-MWCNT-Ag composites and we evaluated their electrical properties to determine the electromagnetic interference shielding performance. We reduced silver nanoparticles in composites using two different in situ methods: UV-reduction and chemical deposition. Composites were characterized using spectroscopic and microscopic tools for evaluation of the chemical, morphological, electrical conductivity and electromagnetic shielding effectiveness. Results from Fourier transform infrared spectroscopy and dispersive Raman microscope showed chemical interactions between silver and the polypyrrole-MWCNT composite due to the charge-transfer within the structure. X-ray diffraction confirmed appearance of two new peaks for silver nanoparticles embedded in polypyrrole-MWCNT independent to reduction method. According to microscopy images, silver nanoparticles were homogenously distributed at the PPy-MWCNTs interfaces by UV reduction, while, chemical reduction resulted to deposition of silver within the PPy matrix. Finally, our results revealed that the polypyrrole-MWCNT-Ag composite produced via UV-reduction has higher electrical conductivity and shielding effectiveness in comparison to chemically reduced one.

A chemical model for lunar non-mare rocks

NASA Technical Reports Server (NTRS)

Hubbard, N. J.; Rhodes, J. M.

1977-01-01

Nearly all rocks returned from the moon are readily divided into three broad categories on the basis of their chemical compositions: (1) mare basalts, (2) non-mare rocks of basaltic composition (KREEP, VHA), and (3) anorthositic rocks. Only mare basalts may unambiguously be considered to have original igneous textures and are widely understood to have an igneous origin. Nearly all other lunar rocks have lost their original textures during metamorphic and impact processes. For these rocks one must work primarily with chemical data in order to recognize and define rock groups and their possible modes of origin. Non-mare rocks of basaltic composition have chemical compositions consistent with an origin by partial melting of the lunar interior. The simplest origin for rocks of anorthositic chemical composition is the crystallization and removal of ferromagnesian minerals. It is proposed that the rock groups of anorthositic and non-mare basaltic chemical composition could have been generated from a single series of original, but not necessarily primitive, lunar materials.

High Pressure Laminates with Antimicrobial Properties

PubMed Central

Magina, Sandra; Santos, Mauro D.; Ferra, João; Cruz, Paulo; Portugal, Inês; Evtuguin, Dmitry

2016-01-01

High-pressure laminates (HPLs) are durable, resistant to environmental effects and good cost-benefit decorative surface composite materials with special properties tailored to meet market demand. In the present work, polyhexamethylene biguanide (PHMB) was incorporated for the first time into melamine-formaldehyde resin (MF) matrix on the outer layer of HPLs to provide them antimicrobial properties. Chemical binding of PHMB to resin matrix was detected on the surface of produced HPLs by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR). Antimicrobial evaluation tests were carried out on the ensuing HPLs doped with PHMB against gram-positive Listeria innocua and gram-negative Escherichia coli bacteria. The results revealed that laminates prepared with 1.0 wt % PHMB in MF resin were bacteriostatic (i.e., inhibited the growth of microorganisms), whereas those prepared with 2.4 wt % PHMB in MF resin exhibited bactericidal activity (i.e., inactivated the inoculated microorganisms). The results herein reported disclose a promising strategy for the production of HPLs with antimicrobial activity without affecting basic intrinsic quality parameters of composite material. PMID:28787897

High Pressure Laminates with Antimicrobial Properties.

PubMed

Magina, Sandra; Santos, Mauro D; Ferra, João; Cruz, Paulo; Portugal, Inês; Evtuguin, Dmitry

2016-02-06

High-pressure laminates (HPLs) are durable, resistant to environmental effects and good cost-benefit decorative surface composite materials with special properties tailored to meet market demand. In the present work, polyhexamethylene biguanide (PHMB) was incorporated for the first time into melamine-formaldehyde resin (MF) matrix on the outer layer of HPLs to provide them antimicrobial properties. Chemical binding of PHMB to resin matrix was detected on the surface of produced HPLs by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR). Antimicrobial evaluation tests were carried out on the ensuing HPLs doped with PHMB against gram-positive Listeria innocua and gram-negative Escherichia coli bacteria. The results revealed that laminates prepared with 1.0 wt % PHMB in MF resin were bacteriostatic ( i.e. , inhibited the growth of microorganisms), whereas those prepared with 2.4 wt % PHMB in MF resin exhibited bactericidal activity ( i.e. , inactivated the inoculated microorganisms). The results herein reported disclose a promising strategy for the production of HPLs with antimicrobial activity without affecting basic intrinsic quality parameters of composite material.

The History of Infant Formula: Quality, Safety, and Standard Methods.

PubMed

Wargo, Wayne F

2016-01-01

Food-related laws and regulations have existed since ancient times. Egyptian scrolls prescribed the labeling needed for certain foods. In ancient Athens, beer and wines were inspected for purity and soundness, and the Romans had a well-organized state food control system to protect consumers from fraud or bad produce. In Europe during the Middle Ages, individual countries passed laws concerning the quality and safety of eggs, sausages, cheese, beer, wine, and bread; some of these laws still exist today. But more modern dietary guidelines and food regulations have their origins in the latter half of the 19th century when the first general food laws were adopted and basic food control systems were implemented to monitor compliance. Around this time, science and food chemistry began to provide the tools to determine "purity" of food based primarily on chemical composition and to determine whether it had been adulterated in any way. Since the key chemical components of mammalian milk were first understood, infant formulas have steadily advanced in complexity as manufacturers attempt to close the compositional gap with human breast milk. To verify these compositional innovations and ensure product quality and safety, infant formula has become one of the most regulated foods in the world. The present paper examines the historical development of nutritional alternatives to breastfeeding, focusing on efforts undertaken to ensure the quality and safety from antiquity to present day. The impact of commercial infant formulas on global regulations is addressed, along with the resulting need for harmonized, fit-for-purpose, voluntary consensus standard methods.

Inventoring Gas in Debris Disks: UV Spectroscopy of Eta Tel

NASA Astrophysics Data System (ADS)

Roberge, Aki

2015-10-01

Debris disks stand between gas-rich protoplanetary disks and mature planetary systems, shedding light on the late stages of planet formation. Their dust component has been extensively studied, yet has provided little information about disk chemical composition. More information can be provided by their gas content, but astonishingly little is known about it. Only two debris disks have measurements of their gas composition, which is shockingly carbon-rich (Beta Pictoris and 49 Ceti). Basic questions remain unanswered. What are the typical gas-to-dust ratios in debris disks? What is the chemical composition of debris gas and its parent material? The answers to these questions have profound implications for terrestrial planet assembly and the origins of planetary atmospheres.Most detections of debris gas to date were achieved with line of sight UV/optical absorption spectroscopy of edge-on disks, using the central star as the background source. This technique is far more sensitive to small amounts of gas than emission line studies. The UV bandpass is particularly important, since strong transitions of numerous atomic and molecular species lie there. We propose extending our intriguing studies of debris gas with STIS UV spectroscopy of a highly promising debris disk system, Eta Tel. This disk is edge-on and contains circumstellar atomic gas (CII). We will measure column densities of the most important gas species, find the relative elemental gas abundances, and determine the gas mass using a powerful gas disk modeling code. We will also divide our observations into two visits, to search for signs of star-grazing exocomets, which are seen in both Beta Pic and 49 Cet.

Rosé wine volatile composition and the preferences of Chinese wine professionals.

PubMed

Wang, Jiaming; Capone, Dimitra L; Wilkinson, Kerry L; Jeffery, David W

2016-07-01

Rosé wine aromas range from fruity and floral, to more developed, savoury characters. Lighter than red wines, rosé wines tend to match well with Asian cuisines, yet little is known about the factors driving desirability of rosé wines in emerging markets such as China. This study involved Chinese wine professionals participating in blind rosé wine tastings comprising 23 rosé wines from Australia, China and France in three major cities in China. According to the sensory results, a link between the preference, quality and expected retail price of the wines was observed, and assessors preferred wines with prominent red fruit, floral, confectionery and honey characters, and without developed attributes or too much sweetness. Basic wine chemical parameters and 47 volatile compounds, including 5 potent thiols, were determined. Correlations between chemical components, sensory attributes and preference/quality/expected price were visualised by network analysis, revealing relationships that are worthy of further investigation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Equations of state for explosive detonation products: The PANDA model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerley, G.I.

1994-05-01

This paper discusses a thermochemical model for calculating equations of state (EOS) for the detonation products of explosives. This model, which was first presented at the Eighth Detonation Symposium, is available in the PANDA code and is referred to here as ``the Panda model``. The basic features of the PANDA model are as follows. (1) Statistical-mechanical theories are used to construct EOS tables for each of the chemical species that are to be allowed in the detonation products. (2) The ideal mixing model is used to compute the thermodynamic functions for a mixture of these species, and the composition ofmore » the system is determined from assumption of chemical equilibrium. (3) For hydrocode calculations, the detonation product EOS are used in tabular form, together with a reactive burn model that allows description of shock-induced initiation and growth or failure as well as ideal detonation wave propagation. This model has been implemented in the three-dimensional Eulerian code, CTH.« less

Sorbent control of trace metals in sewage sludge combustion and incineration

NASA Astrophysics Data System (ADS)

Naruse, I.; Yao, H.; Mkilaha, I. S. N.

2003-05-01

Coal and wastes combustion have become an important issue not only in terms of energy generation but also environmental conservation. The need for alternative fuels and wastes management has made the two energy sources of importance. However, the utilization of the two is faced with problems of impurity trace metals in the fuel. These metals usually speciate during combustion or incineration leading to generation of fumes and subsequently particles. This paper reports on the study aimed at understanding the speciation of trace metals and their emission from combustion systems as particulates. Experiments carried out using a down-flow furnace and theoretical study carried out using lead, chromium and cadmium as basic metals had shown that their speciation and subsequent emission is controlled by both chemical composition and physical properties of the fuel. The physical and chemical and physical properties of the fuel and their respective compounds and the operating conditions of the incineration and combustion system control the enrichment of the particles with trace metals.

Chemical, chromatic, and sensory attributes of 6 red wines produced with prefermentative cold soak.

PubMed

Casassa, L Federico; Bolcato, Esteban A; Sari, Santiago E

2015-05-01

Six red grape cultivars, Barbera D'Asti, Cabernet Sauvignon, Malbec, Merlot, Pinot Noir and Syrah, were produced with or without prefermentative cold soak (CS). Cold soak had no effect on the basic chemical composition of the wines. At pressing, CS wines were more saturated and with a higher red component than control wines. After 1 year of bottle aging, CS wines retained 22% more anthocyanins than control wines, but tannins and total phenolics remained unaffected. Both saturation and the red component of colour were slightly higher in CS wines. From a sensory standpoint, CS only enhanced colour intensity in Barbera D'Asti and Cabernet Sauvignon wines, whereas it diminished colour intensity in Pinot Noir. Cold soak had no effect on perceived aroma, bitterness, astringency, and body of the wines. Principal Component Analysis suggested that the outcome of CS is contingent upon the specific cultivar to which the CS technique is applied. Copyright © 2014 Elsevier Ltd. All rights reserved.

ITO/gold nanoparticle/RGD peptide composites to enhance electrochemical signals and proliferation of human neural stem cells.

PubMed

Kim, Tae-Hyung; El-Said, Waleed Ahmed; An, Jeung Hee; Choi, Jeong-Woo

2013-04-01

A cell chip composed of ITO, gold nanoparticles (GNP) and RGD-MAP-C peptide composites was fabricated to enhance the electrochemical signals and proliferation of undifferentiated human neural stem cells (HB1.F3). The structural characteristics of the fabricated surfaces were confirmed by both scanning electron microscopy and surface-enhanced Raman spectroscopy. HB1.F3 cells were allowed to attach to various composites electrodes in the cell chip and the material-dependent effects on electrochemical signals and cell proliferation were analyzed. The ITO/60 nm GNP/RGD-MAP-C composite electrode was found to be the best material in regards to enhancing the voltammetric signals of HB1.F3 cells when exposed to cyclic voltammetry, as well as for increasing cell proliferation. Differential pulse voltammetry was performed to evaluate the adverse effects of doxorubicin on HB1.F3 cells. In these experiments, negative correlations between cell viability and chemical concentrations were obseved, which were more sensitive than MTT viability assay especially at low concentrations (<0.1 μg/mL). In this basic science study, a cell chip composed of ITO, gold nanoparticles and RGD-MAP-C peptide composites was fabricated to enhance electrochemical signals and proliferation of undifferentiated human neural stem cells (HB1.F3). The ITO/60 nm GNP/RGD-MAP-C composite electrode was found to best enhance the voltammetric signals of the studied cells. Copyright © 2013 Elsevier Inc. All rights reserved.

Growth of multi-component alloy films with controlled graded chemical composition on sub-nanometer scale

DOEpatents

Bajt, Sasa; Vernon, Stephen P.

2005-03-15

The chemical composition of thin films is modulated during their growth. A computer code has been developed to design specific processes for producing a desired chemical composition for various deposition geometries. Good agreement between theoretical and experimental results was achieved.

Continuous magma recharge at Mt. Etna during the 2011-2013 period controls the style of volcanic activity and compositions of erupted lavas

NASA Astrophysics Data System (ADS)

Viccaro, Marco; Calcagno, Rosario; Garozzo, Ileana; Giuffrida, Marisa; Nicotra, Eugenio

2015-02-01

Volcanic rocks erupted during the January 2011 - April 2013 paroxysmal sequence at Mt. Etna volcano have been investigated through in situ microanalysis of mineral phases and whole rock geochemistry. These products have been also considered within the framework of the post-2001 record, evidencing that magmas feeding the 2011-2013 paroxysmal activity inherited deep signature comparable to that of the 2007-2009 volcanic rocks for what concerns their trace element concentration. Analysis performed on plagioclase, clinopyroxene and olivine, which are sensitive to differentiation processes, show respectively fluctuations of the An, Mg# and Fo contents during the considered period. Also major and trace elements measured on the whole rock provide evidence of the evolutionary degree variations through time. Simulations by MELTS at fixed chemical-physical parameters allowed the definition of feeding system dynamics controlling the geochemical variability of magmas during the 2011-2013 period. Specifically, compositional changes have been interpreted as due to superimposition of fractional crystallization and mixing in variable proportions with more basic magma ascending from intermediate to shallower levels of the plumbing system. Composition of the recharging end-member is compatible with that of the most basic magmas emitted during the 2007 and the early paroxysmal eruptions of 2012. Analysis of the erupted volumes of magma combined with its petrologic evolution through time support the idea that large volumes of magma are continuously intruded and stored in the intermediate plumbing system after major recharging phases in the deepest levels of it. Transient recharge from the intermediate to the shallow levels is then responsible for the paroxysmal eruptions.

Origin of reverse compositional and textural zoning in granite plutons by localized thermal overturn of stratified magma chambers

NASA Astrophysics Data System (ADS)

Trubač, Jakub; Janoušek, Vojtěch; Žák, Jiří; Somr, Michael; Kabele, Petr; Švancara, Jan; Gerdes, Axel; Žáčková, Eliška

2017-04-01

This study integrates gravimetry and thermal modelling with petrology, U-Th-Pb monazite and zircon geochronology and whole-rock geochemistry of the early Carboniferous Říčany Pluton, Bohemian Massif, in order to discuss the origin of compositional and textural zoning in granitic plutons and complex histories of horizontally stratified, multiply replenished magma chambers. The pluton consists of two coeval, nested biotite (-muscovite) granite facies: outer one, strongly porphyritic (SPm) and inner one, weakly porphyritic (WPc). Their contact is concealed but is likely gradational over several hundreds of meters. The two facies have nearly identical modal composition, are subaluminous to slightly peraluminous and geochemically evolved. Mafic microgranular enclaves, commonly associated with K-feldspar phenocryst patches, are abundant in the pluton center and indicate a repeated basic magma injection and its multistage interactions with the granitic magma and nearly solidified cumulates. Furthermore, the gravimetric data show that the nested pluton is only a small outcrop of a large anvil-like body reaching the depth of at least 14 km, where the pluton root is expected. Trace-element compositions reveal that the pluton is doubly reversely zoned. On the pluton scale, the outer SRG is geochemically more evolved than the inner WPc. On the scale of individual units, outward whole-rock geochemical variations within each facies (SPm, WPc) are compatible with fractional crystallization dominated by feldspars. The proposed genetic model invokes vertical overturn of a deeper, horizontally stratified anvil-shaped magma chamber. The overturn was driven by reactivation of resident felsic magma from the K-feldspar-rich crystal mush. The energy for the melt remobilization, extraction and subsequent ascent is thought to be provided by a long-lived thermal anomaly above the pluton feeding zone, enhanced by the multiple injections of hot basic magmas. In general, it is concluded that the three-dimensional shape of the granitic bodies exerts a first-order control on their cooling histories and thus also on their physico-chemical evolution. Thicker and longer lived portions of magma chambers are the favourable sites for extensive fractionation and/or, potentially vigorous interaction with the basic magmas. These hot domains are then particularly prone to rejuvenation and subsequent extraction of highly mobile magma leading potentially to volcanic eruptions.

Introduction to Chemistry for Water and Wastewater Treatment Plant Operators. Water and Wastewater Training Program.

ERIC Educational Resources Information Center

South Dakota Dept. of Environmental Protection, Pierre.

Presented are basic concepts of chemistry necessary for operators who manage drinking water treatment plants and wastewater facilities. It includes discussions of chemical terms and concepts, laboratory procedures for basic analyses of interest to operators, and discussions of appropriate chemical calculations. Exercises are included and answer…

Solar system formation and the distribution of volatile species

NASA Technical Reports Server (NTRS)

Lunine, Jonathan I.

1994-01-01

To understand how the solar system formed we must understand the compositional distribution of the current system. Volatile species are particularly important in that their stability as condensed phases is limited in temperature-pressure space, and hence variations in their distribution at present potentially contain an imprint of processes by which temperature and pressure varied in the solar nebula. In this talk we restrict ourselves to species more volatile than water ice, and address issues related to processes in the outer solar system and the formation of bodies there; others in this conference will cover volatile species relevant to inner solar system processes. Study of the outer solar system is relevant both to understanding the interface between the solar nebula and the progenitor giant molecular cloud (since the chemical links to present-day observables in molecular clouds are species like methane, carbon monoxide, etc.), as well as the origin of terrestrial planet atmospheres and oceans (the latter to be covered by Owen). The wealth of compositional information on outer solar system bodies which has become available from spacecraft and ground-based observations challenges traditional simplistic views of the composition and hence dynamics of the solar nebula. The basic assumption of thermochemical equilibrium, promulgated in the 1950's, in which methane and ammonia dominate nitrogen- and carbon-bearing species, is demonstrably incorrect on both observational and theoretical grounds. However, the kinetic inhibition model which replaced it, in which carbon monoxide and molecular nitrogen dominate a nebula which is fully mixed and hence cycles outer solar system gases through a hot, chemically active zone near the disk center, is not supported either by observations. Instead, a picture of the outer solar system emerges in which the gas and grains are a mixture of relatively unaltered, or modestly altered, molecular cloud material, along with a fraction which has been chemically altered in the solar nebula itself (and perhaps giant planet nebulae).

Nectar and pollination drops: how different are they?

PubMed Central

Nepi, Massimo; von Aderkas, Patrick; Wagner, Rebecca; Mugnaini, Serena; Coulter, Andrea; Pacini, Ettore

2009-01-01

Background Pollination drops and nectars (floral nectars) are secretions related to plant reproduction. The pollination drop is the landing site for the majority of gymnosperm pollen, whereas nectar of angiosperm flowers represents a common nutritional resource for a large variety of pollinators. Extrafloral nectars also are known from all vascular plants, although among the gymnosperms they are restricted to the Gnetales. Extrafloral nectars are not generally involved in reproduction but serve as ‘reward’ for ants defending plants against herbivores (indirect defence). Scope Although very different in their task, nectars and pollination drops share some features, e.g. basic chemical composition and eventual consumption by animals. This has led some authors to call these secretions collectively nectar. Modern techniques that permit chemical analysis and protein characterization have very recently added important information about these sugary secretions that appear to be much more than a ‘reward’ for pollinating (floral nectar) and defending animals (extrafloral nectar) or a landing site for pollen (pollination drop). Conclusions Nectar and pollination drops contain sugars as the main components, but the total concentration and the relative proportions are different. They also contain amino acids, of which proline is frequently the most abundant. Proteomic studies have revealed the presence of common functional classes of proteins such as invertases and defence-related proteins in nectar (floral and extrafloral) and pollination drops. Invertases allow for dynamic rearrangement of sugar composition following secretion. Defence-related proteins provide protection from invasion by fungi and bacteria. Currently, only few species have been studied in any depth. The chemical composition of the pollination drop must be investigated in a larger number of species if eventual phylogenetic relationships are to be revealed. Much more information can be provided from further proteomic studies of both nectar and pollination drop that will contribute to the study of plant reproduction and evolution. PMID:19477895

Zeta Potential Measurements on Solid Surfaces for in Vitro Biomaterials Testing: Surface Charge, Reactivity Upon Contact With Fluids and Protein Absorption

PubMed Central

Ferraris, Sara; Cazzola, Martina; Peretti, Veronica; Stella, Barbara; Spriano, Silvia

2018-01-01

Surface properties of biomaterials (e.g., roughness, chemical composition, charge, wettability, and hydroxylation degree) are key features to understand and control the complex interface phenomena that happens upon contact with physiological fluids. Numerous physico-chemical techniques can be used in order to investigate in depth these crucial material features. Among them, zeta potential measurements are widely used for the characterization of colloidal suspensions, but actually poorly explored in the study of solid surfaces, even if they can give significant information about surface charge in function of pH and indirectly about surface functional groups and reactivity. The aim of the present research is application of zeta potential measurements of solid surfaces for the in vitro testing of biomaterials. In particular, bare and surface modified Ti6Al4V samples have been compared in order to evaluate their isoelectric points (IEPs), surface charge at physiological pH, in vitro bioactivity [in simulated body fluid (SBF)] and protein absorption. Zeta potential titration was demonstrated as a suitable technique for the surface characterization of surface treated Ti6Al4V substrates. Significant shift of the isoelectric point was recorded after a chemical surface treatment (because of the exposition of hydroxyl groups), SBF soaking (because of apatite precipitation IEP moves close to apatite one) and protein absorption (IEP moves close to protein ones). Moreover, the shape of the curve gives information about exposed functional groups (e.g., a plateau in the basic range appears due to the exposition of acidic OH groups and in the acidic range due to exposition of basic NH2 groups). PMID:29868575

Use of olivine and plagioclase saturation surfaces for the petrogenetic modeling of recrystallized basic plutonic systems

NASA Technical Reports Server (NTRS)

Hanson, G. N.

1983-01-01

During petrogenetic studies of basic plutonic rocks, there are at least three major questions to be considered: (1) what were the relative proportions of cumulate crystals and intercumulus melt in a given sample? (2) what is the composition and variation in composition of the melts within the pluton? and (3) what is the original composition of the liquids, their source and evolution prior to the time of emplacement? Use of both saturation surfaces can place strong limits on the compositions of potential cumulate phases and intercumulus melts. Consideration of appropriate trace elements can indicate whether a sample is an orthocumulate, adcumulate or mesocumulate. Thus, when trace element and petrographic data are considered together with the saturation surfaces, it should be possible to begin to answer the three major questions given above, even for strongly recrystallized basic plutons.

Chemical hazards in aeromedical aircraft.

PubMed

Tupper, C R

1989-01-01

Several potentially hazardous chemicals are required to make modern military aircraft fly. With each airevac mission, the possibility exists for structural failure of a fluid system, resulting in contamination to flight/medical crews, patients, and passengers. Aeromedical Evacuation Crewmembers (AECMs) need to be aware of the hazardous chemicals used in aircraft and areas where there is an increased risk to those in and around the aircraft. This study identified potential areas for chemical leakage, such as refuel receptacles, hydraulic reservoirs, hydraulic motors, doors, ramps, engines, and more. Further, it identified the basic first aid procedures to perform on people contaminated with jet fuel, hydraulic fluid, engine oil, fire extinguisher agents, LOX and other fluids. First aid procedures are basic and can be performed with supplies and equipment on a routine aeromedical evacuation mission, AECMs trained in a basic awareness of hazardous aircraft chemicals will result in crews better prepared to cope with the unique risks of transporting patients in a complicated military aircraft.

Raman spectroscopy of human skin: looking for a quantitative algorithm to reliably estimate human age

NASA Astrophysics Data System (ADS)

Pezzotti, Giuseppe; Boffelli, Marco; Miyamori, Daisuke; Uemura, Takeshi; Marunaka, Yoshinori; Zhu, Wenliang; Ikegaya, Hiroshi

2015-06-01

The possibility of examining soft tissues by Raman spectroscopy is challenged in an attempt to probe human age for the changes in biochemical composition of skin that accompany aging. We present a proof-of-concept report for explicating the biophysical links between vibrational characteristics and the specific compositional and chemical changes associated with aging. The actual existence of such links is then phenomenologically proved. In an attempt to foster the basics for a quantitative use of Raman spectroscopy in assessing aging from human skin samples, a precise spectral deconvolution is performed as a function of donors' ages on five cadaveric samples, which emphasizes the physical significance and the morphological modifications of the Raman bands. The outputs suggest the presence of spectral markers for age identification from skin samples. Some of them appeared as authentic "biological clocks" for the apparent exactness with which they are related to age. Our spectroscopic approach yields clear compositional information of protein folding and crystallization of lipid structures, which can lead to a precise identification of age from infants to adults. Once statistically validated, these parameters might be used to link vibrational aspects at the molecular scale for practical forensic purposes.

Glue-free assembly of glass fiber reinforced thermoplastics using laser light

NASA Astrophysics Data System (ADS)

Binetruy, C.; Clement, S.; Deleglise, M.; Franz, C.; Knapp, W.; Oumarou, M.; Renard, J.; Roesner, A.

2011-05-01

The use of laser light for bonding of continuous fiber reinforced thermoplastic composites (CFTPC) offers new possibilities to overcome the constraints of conventional joining technologies. Laser bonding is environmentally friendly as no chemical additive or glue is necessary. Accuracy and flexibility of the laser process as well as the quality of the weld seams provide benefits which are already used in many industrial applications. Laser transmission welding has already been introduced in manufacturing of short fiber thermoplastic composites. The laser replaces hot air in tapelaying systems for pre-preg carbon fiber placement. The paper provides an overview concerning the technical basics of the joining process and outline some material inherent characteristics to be considered when using continuous glass fiber reinforced composites The technical feasibility and the mechanical characterization of laser bonded CFTPC are demonstrated. The influence of the different layer configurations on the laser interaction with the material is investigated and the dependency on the mechanical strength of the weld seem is analyzed. The results show that the laser provides an alternative joining technique and offers new perspectives to assemble structural components emerging in automotive or aeronautical manufacturing. It overcomes the environmental and technical difficulties related to existing gluing processes.

Method of producing a chemical hydride

DOEpatents

Klingler, Kerry M.; Zollinger, William T.; Wilding, Bruce M.; Bingham, Dennis N.; Wendt, Kraig M.

2007-11-13

A method of producing a chemical hydride is described and which includes selecting a composition having chemical bonds and which is capable of forming a chemical hydride; providing a source of a hydrocarbon; and reacting the composition with the source of the hydrocarbon to generate a chemical hydride.

49 CFR 1248.101 - Commodity codes required.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Chemical and Fertilizer Minerals. 14711 Barite. 14713 Potash, soda and borate. 14714 Phosphate rock. 14715... Organic Chemicals. 2812 Sodium, potassium, and other basic inorganic chemical compounds and chlorine... industrial organic chemicals. 28184 Alcohols. 2819 Miscellaneous industrial inorganic chemicals. 28193...

Relevance in Basic Composition: Writing Assignments for Technical Students.

ERIC Educational Resources Information Center

Tichenor, Stuart

Generally, students in vocational and technical colleges are in writing classes because they must be, not because they want to be. As a rule, students in basic composition classes have been more or less continually exposed to writing classes since middle school where they been asked to keep journals, read articles and short stories, and write…

Age, Sex, and Body Composition as Predictors of Children's Performance on Basic Motor Abilities and Health-Related Fitness Items.

ERIC Educational Resources Information Center

Pissanos, Becky W.; And Others

1983-01-01

Step-wise linear regressions were used to relate children's age, sex, and body composition to performance on basic motor abilities including balance, speed, agility, power, coordination, and reaction time, and to health-related fitness items including flexibility, muscle strength and endurance and cardiovascular functions. Eighty subjects were in…

Review on effect of chemical, thermal, additive treatment on mechanical properties of basalt fiber and their composites

NASA Astrophysics Data System (ADS)

Jain, Naman; Singh, Vinay Kumar; Chauhan, Sakshi

2017-12-01

Basalt fiber is emerging out the new reinforcing material for composites. To overcome some of the disadvantages of fibers such as poor bonding to polymers, low thermal stability and high moisture absorption fiber characteristics are modified with chemical, thermal and additive treatments. Chemical treatment corrosive resistance to alkali and acid were investigated which were used to clean and modify the surface of fiber for higher bonding with resins. To improve the thermal stability and reduce moisture uptake thermal treatment such as plasma and non thermal plasma were used which increased the surface roughness and change the chemical composition of surface of basalt fiber. Additive treatment is used to improve the mechanical properties of fibers, in basalt fiber additive treatment was done with SiO2 additive because of its chemical composition which contains major content of SiO2. In present investigation review on the effect of different treatment such as chemical, thermal and additive were studied. Effect of these treatment on chemical composition of the surface of basalt fiber and corrosion to acidic and alkali solution were studied with their effect on mechanical properties of basalt fiber and their composite.

Fast classification and compositional analysis of cornstover fractions using Fourier transform near-infrared techniques.

PubMed

Philip Ye, X; Liu, Lu; Hayes, Douglas; Womac, Alvin; Hong, Kunlun; Sokhansanj, Shahab

2008-10-01

The objectives of this research were to determine the variation of chemical composition across botanical fractions of cornstover, and to probe the potential of Fourier transform near-infrared (FT-NIR) techniques in qualitatively classifying separated cornstover fractions and in quantitatively analyzing chemical compositions of cornstover by developing calibration models to predict chemical compositions of cornstover based on FT-NIR spectra. Large variations of cornstover chemical composition for wide calibration ranges, which is required by a reliable calibration model, were achieved by manually separating the cornstover samples into six botanical fractions, and their chemical compositions were determined by conventional wet chemical analyses, which proved that chemical composition varies significantly among different botanical fractions of cornstover. Different botanic fractions, having total saccharide content in descending order, are husk, sheath, pith, rind, leaf, and node. Based on FT-NIR spectra acquired on the biomass, classification by Soft Independent Modeling of Class Analogy (SIMCA) was employed to conduct qualitative classification of cornstover fractions, and partial least square (PLS) regression was used for quantitative chemical composition analysis. SIMCA was successfully demonstrated in classifying botanical fractions of cornstover. The developed PLS model yielded root mean square error of prediction (RMSEP %w/w) of 0.92, 1.03, 0.17, 0.27, 0.21, 1.12, and 0.57 for glucan, xylan, galactan, arabinan, mannan, lignin, and ash, respectively. The results showed the potential of FT-NIR techniques in combination with multivariate analysis to be utilized by biomass feedstock suppliers, bioethanol manufacturers, and bio-power producers in order to better manage bioenergy feedstocks and enhance bioconversion.

Chemical composition and digestibility of Trifolium exposed to elevated ozone and carbon dioxide in a free-air (FACE) fumigation system

Treesearch

R.B. Muntifering; A.H. Chappelka; J.C. Lin; D.F. Karnosky; G.L. Somers

2006-01-01

Tropospheric ozone (O3) and carbon dioxide (CO2) are significant drivers of plant growth and chemical composition. We hypothesized that exposure to elevated concentrations of O3 and CO2, singly and in combination, would modify the chemical composition of Trifolium...

Analytical Methods to Evaluate the Quality of Edible Fats and Oils: The JOCS Standard Methods for Analysis of Fats, Oils and Related Materials (2013) and Advanced Methods.

PubMed

Endo, Yasushi

2018-01-01

Edible fats and oils are among the basic components of the human diet, along with carbohydrates and proteins, and they are the source of high energy and essential fatty acids such as linoleic and linolenic acids. Edible fats and oils are used in for pan- and deep-frying, and in salad dressing, mayonnaise and processed foods such as chocolates and cream. The physical and chemical properties of edible fats and oils can affect the quality of oil foods and hence must be evaluated in detail. The physical characteristics of edible fats and oils include color, specific gravity, refractive index, melting point, congeal point, smoke point, flash point, fire point, and viscosity, while the chemical characteristics include acid value, saponification value, iodine value, fatty acid composition, trans isomers, triacylglycerol composition, unsaponifiable matters (sterols, tocopherols) and minor components (phospholipids, chlorophyll pigments, glycidyl fatty acid esters). Peroxide value, p-anisidine value, carbonyl value, polar compounds and polymerized triacylglycerols are indexes of the deterioration of edible fats and oils. This review describes the analytical methods to evaluate the quality of edible fats and oils, especially the Standard Methods for Analysis of Fats, Oils and Related Materials edited by Japan Oil Chemists' Society (the JOCS standard methods) and advanced methods.

Chemical composition, toxicity and non-target effects of Pinus kesiya essential oil: An eco-friendly and novel larvicide against malaria, dengue and lymphatic filariasis mosquito vectors.

PubMed

Govindarajan, Marimuthu; Rajeswary, Mohan; Benelli, Giovanni

2016-07-01

Mosquitoes (Diptera: Culicidae) are vectors of important parasites and pathogens causing death, poverty and social disability worldwide, with special reference to tropical and subtropical countries. The overuse of synthetic insecticides to control mosquito vectors lead to resistance, adverse environmental effects and high operational costs. Therefore, the development of eco-friendly control tools is an important public health challenge. In this study, the mosquito larvicidal activity of Pinus kesiya leaf essential oil (EO) was evaluated against the malaria vector Anopheles stephensi, the dengue vector Aedes aegypti and the lymphatic filariasis vector Culex quinquefasciatus. The chemical composition of the EO was analyzed by gas chromatography-mass spectroscopy. GC-MS revealed that the P. kesiya EO contained 18 compounds. Major constituents were α-pinene, β-pinene, myrcene and germacrene D. In acute toxicity assays, the EO showed significant toxicity against early third-stage larvae of An. stephensi, Ae. aegypti and Cx. quinquefasciatus, with LC50 values of 52, 57, and 62µg/ml, respectively. Notably, the EO was safer towards several aquatic non-target organisms Anisops bouvieri, Diplonychus indicus and Gambusia affinis, with LC50 values ranging from 4135 to 8390µg/ml. Overall, this research adds basic knowledge to develop newer and safer natural larvicides from Pinaceae plants against malaria, dengue and filariasis mosquito vectors. Copyright © 2016 Elsevier Inc. All rights reserved.

Antibacterial, Antibiofilm Effect of Burdock (Arctium lappa L.) Leaf Fraction and Its Efficiency in Meat Preservation.

PubMed

Lou, Zaixiang; Li, Cheng; Kou, Xingran; Yu, Fuhao; Wang, Hongxin; Smith, Gary M; Zhu, Song

2016-08-01

First, the antibacterial, antibiofilm effect and chemical composition of burdock (Arctium lappa L.) leaf fractions were studied. Then, the efficiency of burdock leaf fractions in pork preservation was evaluated. The results showed that burdock leaf fraction significantly inhibited the growth and biofilm development of Escherichia coli and Salmonella Typhimurium. MICs of burdock leaf fractions on E. coli and Salmonella Typhimurium were both 2 mg/ml. At a concentration of 2.0 mg/ml, the inhibition rates of the fraction on growth and development of E. coli and Salmonella Typhimurium biofilms were 78.7 and 69.9%, respectively. During storage, the log CFU per gram of meat samples treated with burdock leaf fractions decreased 2.15, compared with the samples without treatment. The shelf life of pork treated with burdock leaf fractions was extended 6 days compared with the pork without treatment, and the sensory property was obviously improved. Compared with the control group, burdock leaf fraction treatment significantly decreased the total volatile basic nitrogen value and pH of the meat samples. Chemical composition analysis showed that the burdock leaf fraction consisted of chlorogenic acid, caffeic acid, p-coumaric acid, rutin, cynarin, crocin, luteolin, arctiin, and quercetin. As a vegetable with an abundant source, burdock leaf is safe, affordable, and efficient in meat preservation, indicating that burdock leaf fraction is a promising natural preservative for pork.

Functionalization of semiconductors for biosensing applications

NASA Astrophysics Data System (ADS)

Estephan, E.; Larroque, C.; Martineau, P.; Cloitre, T.; Gergely, Cs.

2007-05-01

Functionalization of semiconductors (SC) has been widely used for various electronic, photonic and biomedical applications. In this paper, we report on selective functionalization achieved by peptides that reveal specific recognition of the SC surfaces. A M13 bacteriophage library was used to screen 10 10 different 12-mer peptide on various SC substrates to successfully isolate after 3 cycles one specific peptide for the majority of semiconductors. Our results conclude that GaAs(100) and GaN(0001) retain the same sequence of 12-mer peptide, suggesting that the specificity does not depend on the crystallographic structure but it depends on the chemical composition and the electronegativity of the surface, thus on the orientation of the material. We also note the presence of at least one proline (Pro) amino acid in each peptide, and the presence of the histidine (His) in the specific peptides for the II-VI class SC. Pro imprints a constraint to the peptide to facilitate adhesion to the surface, whereas the basic side chain His is known for its affinity towards some of the elements of class II SC. Finally, fluorescence microscopy has been employed to demonstrate the preferential attachment of the peptide to their specific SC surface in close proximity to a surface of different chemical and structural composition. The use of selected peptides expressed by phage display can be extended to encompass a variety of nanostructured semiconductor based devices.

The Effective Concepts on Students' Understanding of Chemical Reactions and Energy

ERIC Educational Resources Information Center

Ayyildiz, Yildizay; Tarhan, Leman

2012-01-01

The purpose of this study was to determine the relationship between the basic concepts related to the unit of "Chemical Reactions and Energy" and the sub-concepts underlying for meaningful learning of the unit and to investigate the effectiveness of them on students' learning achievements. For this purpose, the basic concepts of the unit…

An Overview of Recent Development in Composite Catalysts from Porous Materials for Various Reactions and Processes

PubMed Central

Xie, Zaiku; Liu, Zhicheng; Wang, Yangdong; Yang, Qihua; Xu, Longya; Ding, Weiping

2010-01-01

Catalysts are important to the chemical industry and environmental remediation due to their effective conversion of one chemical into another. Among them, composite catalysts have attracted continuous attention during the past decades. Nowadays, composite catalysts are being used more and more to meet the practical catalytic performance requirements in the chemical industry of high activity, high selectivity and good stability. In this paper, we reviewed our recent work on development of composite catalysts, mainly focusing on the composite catalysts obtained from porous materials such as zeolites, mesoporous materials, carbon nanotubes (CNT), etc. Six types of porous composite catalysts are discussed, including amorphous oxide modified zeolite composite catalysts, zeolite composites prepared by co-crystallization or overgrowth, hierarchical porous catalysts, host-guest porous composites, inorganic and organic mesoporous composite catalysts, and polymer/CNT composite catalysts. PMID:20559508

Cell-free biology: exploiting the interface between synthetic biology and synthetic chemistry

PubMed Central

Harris, D. Calvin; Jewett, Michael C.

2014-01-01

Just as synthetic organic chemistry once revolutionized the ability of chemists to build molecules (including those that did not exist in nature) following a basic set of design rules, cell-free synthetic biology is beginning to provide an improved toolbox and faster process for not only harnessing but also expanding the chemistry of life. At the interface between chemistry and biology, research in cell-free synthetic systems is proceeding in two different directions: using synthetic biology for synthetic chemistry and using synthetic chemistry to reprogram or mimic biology. In the coming years, the impact of advances inspired by these approaches will make possible the synthesis of non-biological polymers having new backbone compositions, new chemical properties, new structures, and new functions. PMID:22483202

Development of the earth-moon system with implications for the geology of the early earth

NASA Technical Reports Server (NTRS)

Smith, J. V.

1976-01-01

Established facts regarding the basic features of the earth and the moon are reviewed, and some important problems involving the moon are discussed (extent of melting, time of crustal differentiation and nature of bombardment, bulk chemical composition, and nature and source of mare basins), with attention given to the various existing theories concerning these problems. Models of the development of the earth-moon system from the solar nebula are examined, with particular attention focused on those that use the concept of capture with disintegration. Impact processes in the early crust of the earth are briefly considered, with attention paid to Green's (1972) suggestion that Archaean greenstone belts may be the terrestrial equivalent of lunar maria.

Studies of silicon pn junction solar cells

NASA Technical Reports Server (NTRS)

Lindholm, F. A.; Neugroschel, A.

1977-01-01

Modifications of the basic Shockley equations that result from the random and nonrandom spatial variations of the chemical composition of a semiconductor were developed. These modifications underlie the existence of the extensive emitter recombination current that limits the voltage over the open circuit of solar cells. The measurement of parameters, series resistance and the base diffusion length is discussed. Two methods are presented for establishing the energy bandgap narrowing in the heavily-doped emitter region. Corrections that can be important in the application of one of these methods to small test cells are examined. Oxide-charge-induced high-low-junction emitter (OCI-HLE) test cells which exhibit considerably higher voltage over the open circuit than was previously seen in n-on-p solar cells are described.

Sputtering. [as deposition technique in mechanical engineering

NASA Technical Reports Server (NTRS)

Spalvins, T.

1976-01-01

This paper primarily reviews the potential of using the sputtering process as a deposition technique; however, the manufacturing and sputter etching aspects are also discussed. Since sputtering is not regulated by classical thermodynamics, new multicomponent materials can be developed in any possible chemical composition. The basic mechanism for dc and rf sputtering is described. Sputter-deposition is described in terms of the unique advantageous features it offers such as versatility, momentum transfer, stoichiometry, sputter-etching, target geometry (coating complex surfaces), precise controls, flexibility, ecology, and sputtering rates. Sputtered film characteristics, such as strong adherence and coherence and film morphology, are briefly evaluated in terms of varying the sputtering parameters. Also described are some of the specific industrial areas which are turning to sputter-deposition techniques.

Models of the earth's core

NASA Technical Reports Server (NTRS)

Stevenson, D. J.

1981-01-01

Combined inferences from seismology, high-pressure experiment and theory, geomagnetism, fluid dynamics, and current views of terrestrial planetary evolution lead to models of the earth's core with five basic properties. These are that core formation was contemporaneous with earth accretion; the core is not in chemical equilibrium with the mantle; the outer core is a fluid iron alloy containing significant quantities of lighter elements and is probably almost adiabatic and compositionally uniform; the more iron-rich inner solid core is a consequence of partial freezing of the outer core, and the energy release from this process sustains the earth's magnetic field; and the thermodynamic properties of the core are well constrained by the application of liquid-state theory to seismic and labroatory data.

Poly(aryl ethers) and related polysiloxane copolymer molecular coatings: Preparation and radiation degradation

NASA Technical Reports Server (NTRS)

Mcgrath, J. E.

1982-01-01

The radiation degradation of poly(arylene ether sulfones) and related materials is studied. These basic studies are important both as a means to developing stronger, more stable matrix resins for composite materials, as well as to improve the data base in regard to chemical structure-physical property relationships. Thirty homo and copolymers were synthesized, at least partially characterized and, in several cases suitable film casting techniques were developed. Four samples were chosen for initial radiation degradation. Poly(dimethyl siloxane) soft bocks/segments can preferentially migrate to the surface of copolymer films. Since siloxanes are utilized as thermal control coatings, this form of 'molecular' coating is of interest. The chemistry for preparing such copolymers with any of the polymers described was demonstrated.

Estimation of chemical carcass composition from 8th rib characteristics with Belgian blue double-muscled bulls.

PubMed

De Campeneere, S; Fiems, L O; Van de Voorde, G; Vanacker, J M; Boucque, C V; Demeyer, D I

1999-01-01

Characteristics from the 8th rib cut: chemical composition, tissue composition after dissection, specific gravity (SG) and m. longissimus thoracis (LT) composition, collected on 17 Belgian Blue double-muscled fattening bulls were used to generate equations for predicting chemical carcass composition. Carcass composition was best predicted from chemical analysis of the 8th rib cut and the empty body weight (EBW) of the bull. Carcass chemical fat content (CCF, kg) was predicted from the 8th rib cut fat content (ether extract, 8RF, kg) by the following regression: CCF=1.94+27.37 8RF (R(2)=0.957, RSD =9.89%). A higher coefficient was found for carcass water (CCW, kg) predicted from 8RF and EBW: CCW=-2.26+0.28 EBW-34.28 8RF (R(2)=0.997, RSD=1.48%). No parameter was found to improve the prediction of CCP from EBW solely: CCP=-0.86+0.08 EBW (R(2) =0.992, RSD=2.61%). Prediction equations based solely on LT composition had low R(2) values of between 0.38 and 0.67, whereas no significant equations were found using SG. However, equations based on EBW had R(2) values between 0.78 and 0.99. Chemical components of the 8th rib cut in combination with EBW are most useful in predicting the chemical composition of the carcass of Belgian-Blue double-muscled bulls.

Study of chloride ion transport of composite by using cement and starch as a binder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armynah, Bidayatul; Halide, Halmar; Zahrawani,

This study presents the chemical bonding and the structural properties of composites from accelerator chloride test migration (ACTM). The volume fractions between binder (cement and starch) and charcoal in composites are 20:80 and 60:40. The effect of the binder to the chemical composition, chemical bonding, and structural properties before and after chloride ion passing through the composites was determined by X-ray fluorescence (XRF), by Fourier transform infra-red (FTIR), and x-ray diffraction (XRD), respectively. From the XRD data, XRF data, and the FTIR data shows the amount of chemical composition, the type of binding, and the structure of composites are dependingmore » on the type of binder. The amount of chloride migration using starch as binder is higher than that of cement as a binder due to the density effects.« less

Pulsed plasma chemical synthesis of SixCyOz composite nanopowder

NASA Astrophysics Data System (ADS)

Kholodnaya, G.; Sazonov, R.; Ponomarev, D.; Remnev, G.

2017-05-01

SixCyOz composite nanopowder with an average size of particles about 10-50 nm was produced using the pulsed plasma chemical method. The experiments on the synthesis of nanosized composite were carried out using a TEA-500 pulsed electron accelerator. To produce a composite, SiCl4, O2, and CH4 were used. The major part of experiments was conducted using a plasma chemical reactor (quartz, 140 mm diameter, 6 l volume). The initial reagents were injected into the reactor, then a pulsed electron beam was injected which initiated the chemical reactions whose products were the SixCyOz composite nanopowder. To define the morphology of the particles, the JEOL-II-100 transmission electron microscope (TEM) with an accelerating voltage of 100 kV was used. The substances in the composition of the composite nanopowder were identified using the infrared absorption optical spectrum. To conduct this analysis, the Nicolet 5700 FT-IR spectrometer was used.

Chemical durability of alkali-borosilicate glasses studied by analytical SEM, IBA, isotopic-tracing and SIMS

NASA Astrophysics Data System (ADS)

Trocellier, P.; Djanarthany, S.; Chêne, J.; Haddi, A.; Brass, A. M.; Poissonnet, S.; Farges, F.

2005-10-01

Simple and complex alkali-borosilicate glasses were submitted to aqueous corrosion at room temperature, 60 and 90 °C in solutions with pH ranging between 0 and 12. Analytical scanning electron microscopy (SEM), ion beam analysis (IBA) techniques, isotopic tracing and secondary ion mass-depth profiling (SIMS) have been used to investigate the variations of the surface composition of glass. In acidic medium, the glass surface is generally covered by a thick hydrated silica layer, mobile elements like Li, Na and B and transition elements (Fe, Zr, Mo, etc.) are strongly depleted. Near pH 7, relative enrichments of aluminium, iron and rare earths are shown together with strong Li, Na and B depletions. In basic medium, the glass surface exhibits relative enrichments of the major part of transition metals (from Cr to U) whereas mobile elements seem to be kept close to their nominal concentration level at the glass surface and Si is severely impoverished. Hydrogen incorporated at the glass surface after leaching is much more immobile in neutral and basic media than in acid medium.

Better VPS Fabrication of Crucibles and Furnace Cartridges

NASA Technical Reports Server (NTRS)

Holmes, Richard R.; Zimmerman, Frank R.; O'Dell, J. Scott; McKechnie, Timothy N.

2003-01-01

An experimental investigation has shown that by (1) vacuum plasma spraying (VPS) of suitable refractory metal alloys on graphite mandrels, and then (2) heat-treating the VPS alloy deposits under suitable conditions, it is possible to fabricate improved crucibles and furnace cartridges that could be used at maximum temperatures between 1,400 and 1,600 C and that could withstand chemical attack by the materials to be heated in the crucibles and cartridges. Taken by itself, the basic concept of fabricating furnace cartridges by VPS of refractory materials onto graphite mandrels is not new; taken by itself, the basic concept of heat treatment of VPS deposits for use as other than furnace cartridges is also not new; however, prior to this investigation, experimental crucibles and furnace cartridges fabricated by VPS had not been heat treated and had been found to be relatively weak and brittle. Accordingly, the investigation was directed toward determining whether certain combinations of (1) refractory alloy compositions, (2) VPS parameters, and (3) heat-treatment parameters could result in VPS-fabricated components with increased ductility.

Role of steel slags on biomass/carbon dioxide gasification integrated with recovery of high temperature heat.

PubMed

Sun, Yongqi; Liu, Qianyi; Wang, Hao; Zhang, Zuotai; Wang, Xidong

2017-01-01

Disposal of biomass in the agriculture and steel slags in the steel industry provides a significant solution toward sustainability in China. Herein these two sectors were creatively combined as a novel method, i.e., biomass/CO 2 gasification using waste heat from hot slags where the influence of chemical compositions of steel slags, characterized as iron oxide content and basicity, on gasification thermodynamics, was systemically reported for the first time. Both the target gases of CO, H 2 and CH 4 and the polluted gases of NH 3 , NO and NO 2 were considered. It was first found that an increasing iron content and slag basicity continuously improved the CO yield at 600-1000°C and 800-1000°C, respectively; while the effect on polluted gas releases was limited. Moreover, the solid wastes after gasification could be utilized to provide nutrients and improve the soil in the agriculture, starting from which an integrated modern system was proposed herein. Copyright © 2016 Elsevier Ltd. All rights reserved.

Carbon fiber CVD coating by carbon nanostructured for space materials protection against atomic oxygen

NASA Astrophysics Data System (ADS)

Pastore, Roberto; Bueno Morles, Ramon; Micheli, Davide

2016-07-01

In recent years, the emphasis in space research has been shifting from space exploration to commercialization of space. In order to utilize space for commercial purposes it is necessary to understand the low earth orbit (LEO) space environment where most of the activities will be carried out. The studies on the LEO environment are mainly focused towards understanding the effect of atomic oxygen (AO) on spacecraft materials. In the first few shuttle flights, materials looked frosty because they were actually being eroded and textured: AO reacts with organic materials on spacecraft exteriors, gradually damaging them. When a spacecraft travel in LEO (where crewed vehicles and the International Space Station fly), the AO formed from the residual atmosphere can react with the spacecraft surfaces, causing damage to the vehicle. Polymers are widely used in space vehicles and systems as structural materials, thermal blankets, thermal control coatings, conformal coatings, adhesives, lubricants, etc. Exposure of polymers and composites to the space environment may result in different detrimental effects via modification of their chemical, electrical, thermal, optical and mechanical properties as well as surface erosion. The major degradation effects in polymers are due to their exposure to atomic oxygen, vacuum ultraviolet and synergistic effects, which result in different damaging effects by modification of the polymer's chemical properties. In hydrocarbon containing polymers the main AO effect is the surface erosion via chemical reactions and the release of volatile reaction products associated with the mass loss. The application of a thin protective coating to the base materials is one of the most commonly used methods of preventing AO degradation. The purpose is to provide a barrier between base material and AO environment or, in some cases, to alter AO reactions to inhibit its diffusion. The effectiveness of a coating depends on its continuity, porosity, degree of adhesion and durability in the environment. Though these coatings are efficient in protecting polymer composites, their application imposes severe constraints. Their thermal expansion coefficients may differ markedly from those of polymer composite substrates: as a result, cracks develop in the coatings on thermal cycling and AO can penetrate through them to the substrate. In addition to the technicalities of forming an effective barrier, such factors as cost, convenience of application and ease of repair are important considerations in the selection of a coating for a particular application. The latter issues drive the aerospace research toward the development of novel light composite materials, like the so called polymer nanocomposites, which are materials with a polymer matrix and a filler with at least one dimension less than 100 nanometers. Current interest in nanocomposites has been generated and maintained because nanoparticle-filled polymers exhibit unique combinations of properties not achievable with traditional composites. These combinations of properties can be achieved because of the small size of the fillers, the large surface area the fillers provide, and in many cases the unique properties of the fillers themselves. In particular, the carbon fiber-based polymeric composite materials are the basic point of interest: the aim of the present study is to find new solution to produce carbon fiber-based composites with even more upgraded performances. One intriguing strategy to tackle such an issue has been picked out in the coupling between the carbon fibers and the carbon nanostructures. That for two main reasons: first, carbon nanostructures have shown fancy potentialities for any kind of technological applications since their discovery, second, the chemical affinity between fiber and nanostructure (made of the same element) should be a likely route to approach the typical problems due to thermo-mechanical compatibility. This work is joined in such framework, by the purpose to integrate the carbon nanostructures in the carbon fibers by means of chemical vapor deposition (CVD) method, in order to develop the basic substrate of advanced carbon-based nanocomposite for atomic oxygen protection. The nanostructures grown onto the carbon fibers can be used to create multiscale hybrid carbon nanotube/carbon fiber composites where individual carbon fibers, which are several microns in diameter, are surrounded by nanotubes. The present objective is the setting-up of the CVD parameters for a reliable growth of carbon nanostructures on carbon fiber surface; after that, the results of a preliminary characterization related to atomic oxygen effects testing by means of a ground LEO simulation facility are reported and discussed.

Preparation, characterization and catalyst application of ternary interpenetrating networks of poly 4-methyl vinyl pyridinium hydroxide-SiO{sub 2}-Al{sub 2}O{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalbasi, Roozbeh Javad, E-mail: rkalbasi@iaush.ac.ir; Kolahdoozan, Majid, E-mail: kolahdoozan@iaush.ac.ir; Vanani, Sedigheh Mozafari

2011-08-15

In this work, Al{sub 2}O{sub 3} was mixed with SiO{sub 2} and poly 4-vinylpyridine by the sol-gel method in order to make a composite which is used as a heterogeneous basic catalyst for Knoevenagel condensation reaction. The physical and chemical properties of the composite catalyst were investigated by XRD, FT-IR, TG, BET and SEM techniques. The catalytic performance of each material was determined for the Knoevenagel condensation reaction between carbonyl compound and malononitrile. The reactions were performed in solvent-free conditions and the product was obtained in high yield and purity after a simple work-up. The effects of the amount ofmore » catalyst, amount of monomer for the synthesis of composite and recyclability of the heterogeneous composite were investigated. The composite catalyst used for this synthetically useful transformation showed considerable level of reusability besides very good activity. - Graphical abstract: In this paper, we report the synthesis of poly 4-methyl vinyl pyridinium hydroxide-SiO{sub 2}-Al{sub 2}O{sub 3}. The novelty of this procedure is at easy preparation together with using inexpensive materials. Highlights: > P4MVPH-SiO{sub 2}-Al{sub 2}O{sub 3} composite was prepared as a novel polymer-inorganic hybrid. > The composite was prepared without using any bridged organosilanes compound. > SEM photograph showed that the composite is completely uniform. > P4MVPH-SiO{sub 2}-Al{sub 2}O{sub 3} could behave as a recyclable catalyst for Knoevenagel reaction.« less

Synthesis, dynamics and photophysics of nanoscale systems

NASA Astrophysics Data System (ADS)

Mirkovic, Tihana

The emerging field of nanotechnology, which spans diverse areas such as nanoelectronics, medicine, chemical and pharmaceutical industries, biotechnology and computation, focuses on the development of devices whose improved performance is based on the utilization of self-assembled nanoscale components exhibiting unique properties owing to their miniaturized dimensions. The first phase in the conception of such multifunctional devices based on integrated technologies requires the study of basic principles behind the functional mechanism of nanoscale components, which could originate from individual nanoobjects or result as a collective behaviour of miniaturized unit structures. The comprehensive studies presented in this thesis encompass the mechanical, dynamical and photophysical aspects of three nanoscale systems. A newly developed europium sulfide nanocrystalline material is introduced. Advances in synthetic methods allowed for shape control of surface-functionalized EuS nanocrystals and the fabrication of multifunctional EuS-CdSe hybrid particles, whose unique structural and optical properties hold promise as useful attributes of integrated materials in developing technologies. A comprehensive study based on a new class of multifunctional nanomaterials, derived from the basic unit of barcoded metal nanorods is presented. Their chemical composition affords them the ability to undergo autonomous motion in the presence of a suitable fuel. The nature of their chemically powered self-propulsion locomotion was investigated, and plausible mechanisms for various motility modes were presented. Furthermore functionalization of striped metallic nanorods has been realized through the incorporation of chemically controlled flexible hinges displaying bendable properties. The structural aspect of the light harvesting machinery of a photosynthetic cryptophyte alga, Rhodomonas CS24, and the mobility of the antenna protein, PE545, in vivo were investigated. Information obtained through a combination of steady-state and time-resolved spectroscopy in conjunction with quantum chemical calculations aided in the elucidation of the dynamics and the mechanism of light harvesting in the multichromophoric phycobiliprotein phycocyanin PC645 in vitro. Investigation of the light-harvesting efficiency and optimization of energy transfer with respect to the structural organization of light-harvesting chromophores on the nanoscale, can provide us with fundamental information necessary for the development of synthetic light-harvesting devices capable of mimicking the efficiency of the natural system.

Impacts of the mixing state and chemical composition on the cloud condensation nuclei (CCN) activity in Beijing during winter, 2016

NASA Astrophysics Data System (ADS)

Ren, J.; Zhang, F.

2017-12-01

Abstract.Understanding aerosol chemical composition and mixing state on CCN activity in polluted urban area is crucial to determine NCCN accurately and thus to quantify aerosol indirect effects. Aerosol hrgroscopicity, size-resolved cloud condensation nuclei (CCN) concentration and chemical composition are measured under polluted and background conditions in Beijing based on the Air Pollution and Human Health (APHH) field campaign in winter 2016. The CCN number concentration (NCCN) is predicted by using κ-Köhler theory from the PNSD and five simplified of the mixing state and chemical composition. The assumption of EIS (sulfate, nitrate and SOA internally mixed, and POA and BC externally mixed with size-resolved chemical composition) shows the best closure to predict NCCN with the ratio of predicted to measured NCCN of 0.96-1.12 both in POL and BG conditions. Under BG conditions, IB (internal mixture with bulk chemical composition) scheme achieves the best CCN closure during any periods of a day. In polluted days, EIS and IS (internal mixture with size-resolved chemical composition) scheme may achieve better closure than IB scheme due to the heterogeneity in particles composition across different size. ES (external mixture with size-resolved chemical composition) and EB (external mixture with bulk chemical composition) scheme markedly underestimate the NCCN with the ratio of predicted to measured NCCN of 0.6-0.8. In addition, we note that assumptions of size-resolved composition (IS or ES) show very limited promotes by comparing with the assumptions of bulk composition (IB or EB), furthermore, the prediction becomes worse by using size-resolved assumption in clean days. The predicted NCCN during eve-rush periods shows the most sensitivity to the five different assumptions, with ratios of the predicted and measured NCCN ranging from 0.5 to 1.4, reflecting great impacts from evening traffic and cooking sources. The result from the sensitivity examination of predict NCCN to particles mixing state and organic volume fractions with the aging of organic particles suggests that the mixing state of particles plays a minor role when the κorg exceeds 0.1. Our study could provide new dataset to evaluate the CCN parameterization in models in those heavily polluted regions with large fraction of POA and BC.

Laboratory Inquiry for Determining the Chemical Composition of a Component in a Daily Use Detergent: Sodium Sesquicarbonate

ERIC Educational Resources Information Center

Koga, Nobuyoshi; Kimura, Tomoyasu; Shigedomi, Kana

2011-01-01

An inquiry-based laboratory activity to determine the chemical composition of a component in alkaline detergents, sodium sesquicarbonate (SSC), is proposed. On the basis of introductory demonstrations by the instructor on the chemical properties and reactions of SSC, students propose the hypothetical composition of SSC and possible quantitative…

A Study of Chemical Composition of δ Scuti-Type Stars Based on the Observations with the BTA and RTT-150

NASA Astrophysics Data System (ADS)

Galeev, A. I.; Berdnikova, V. M.; Ivanova, D. V.; Kudryavtsev, D. O.; Shimanskaya, N. N.; Shimansky, V. V.; Balashova, M. O.

2017-06-01

The results of a study of a sample of δ Scuti-type stars obtained from the observations with the BTA and RTT-150 are presented. Based on photometric data, we measured and analyzed the fundamental parameters of all the studied stars. For eight stars (for two of them for the first time), the fundamental parameters of the atmospheres (Teff, log g, [Fe/H]) and the chemical composition for 29 elements in the LTE-approximation are received using spectroscopic observations. The chemical composition analysis demonstrates both the solar abundances of chemical elements and the anomalies of chemical composition typical of Am stars in the studied sample of δ Scuti-type stars.

The use of computer-assisted image analysis in the evaluation of the effect of management systems on changes in the color, chemical composition and texture of m. longissimus dorsi in pigs.

PubMed

Zapotoczny, Piotr; Kozera, Wojciech; Karpiesiuk, Krzysztof; Pawłowski, Rodian

2014-08-01

The effect of management systems on selected physical properties and chemical composition of m. longissimus dorsi was studied in pigs. Muscle texture parameters were determined by computer-assisted image analysis, and the color of muscle samples was evaluated using a spectrophotometer. Highly significant correlations were observed between chemical composition and selected texture variables in the analyzed images. Chemical composition was not correlated with color or spectral distribution. Subject to the applied classification methods and groups of variables included in the classification model, the experimental groups were identified correctly in 35-95%. No significant differences in the chemical composition of m. longissimus dorsi were observed between experimental groups. Significant differences were noted in color lightness (L*) and redness (a*). Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermally emissive sensing materials for chemical spectroscopy analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poole, Zsolt; Ohodnicki, Paul R.

A sensor using thermally emissive materials for chemical spectroscopy analysis includes an emissive material, wherein the emissive material includes the thermally emissive materials which emit electromagnetic radiation, wherein the electromagnetic radiation is modified due to chemical composition in an environment; and a detector adapted to detect the electromagnetic radiation, wherein the electromagnetic radiation is indicative of the chemical interaction changes and hence chemical composition and/or chemical composition changes of the environment. The emissive material can be utilized with an optical fiber sensor, with the optical fiber sensor operating without the emissive material probed with a light source external to themore » material.« less

Technetium-99m: basic nuclear physics and chemical properties.

PubMed

Castronovo, F P

1975-05-01

The nuclear physics and chemical properties of technetium-99m are reviewed. The review of basic nuclear physics includes: classification of nuclides, nuclear stability, production of radionuclides, artificial production of molybdenum-99, production of technetium 99m and -99Mo-99mTc generators. The discussion of the chemistry of technetium includes a profile of several -99mCc-labeled radiopharmaceuticals.

Using the Chemistry of Fireworks to Engage Students in Learning Basic Chemical Principles: A Lesson in Eco-Friendly Pyrotechnics

ERIC Educational Resources Information Center

Steinhauser, Georg; Klapotke, Thomas M.

2010-01-01

Fascination with fireworks and pyrotechnics can be used for educational purposes. Several aspects of pyrochemistry such as redox reactions, flame colors, or the theory of combustion can be incorporated in the curriculum to illustrate some basic chemical principles, guaranteeing a lesson that will be engaging and memorable. Beyond classic…

Characterizing the variability in chemical composition of flowback and produced waters - results from lab and field studies

NASA Astrophysics Data System (ADS)

Vieth-Hillebrand, Andrea; Wilke, Franziska D. H.; Schmid, Franziska E.; Zhu, Yaling; Lipińska, Olga; Konieczyńska, Monika

2017-04-01

The huge volumes and unknown composition of flowback and produced waters cause major public concerns about the environmental and social compatibility of hydraulic fracturing and the exploitation of gas from unconventional reservoirs. Flowback and produced waters contain not only residues of fracking additives but also chemical species that are dissolved from the target shales themselves. Shales are a heterogeneous mixture of minerals, organic matter, and formation water and little is actually understood about the fluid-rock interactions occurring during hydraulic fracturing of the shales and their effects on the chemical composition of flowback and produced water. To overcome this knowledge gap, interactions of different shales with different artificial stimulation fluids were studied in lab experiments under ambient and elevated temperature and pressure conditions. These lab experiments showed clearly that fluid-rock interactions change the chemical composition of the initial stimulation fluid and that geochemistry of the fractured shale is relevant for understanding flowback water composition. In addition, flowback water samples were taken after hydraulic fracturing of one horizontal well in Pomeranian region, Poland and investigated for their chemical composition. With this presentation, results from lab and field studies will be presented and compared to decipher possible controls on chemical compositions of flowback and produced water.

Summaries of FY 1979 research in the chemical sciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-05-01

The purpose of this report is to help those interested in research supported by the Department of Energy's Division of Chemical Sciences, which is one of six Divisions of the Office of Basic Energy Sciences in the Office of Energy Research. Chemists, physicists, chemical engineers and others who are considering the possibility of proposing research for support by this Division wll find the booklet useful for gauging the scope of the program in basic research, and the relationship of their interests to the overall program. These smmaries are intended to provide a rapid means for becoming acquainted with the Chemicalmore » Sciences program for members of the scientific and technological public, and interested persons in the Legislative and Executive Branches of the Government, in order to indicate the areas of research supported by the Division and energy technologies which may be advanced by use of basic knowledge discovered in this program. Scientific excellence is a major criterion applied in the selection of research supported by Chemical Sciences. Another important consideration is the identifying of chemical, physical and chemical engineering subdisciplines which are advancing in ways which produce new information related to energy, needed data, or new ideas.« less

[Bioinorganic chemical composition of the lens and methods of its investigation].

PubMed

Avetisov, S E; Novikov, I A; Pakhomova, N A; Motalov, V G

2018-01-01

Bioinorganic chemical composition of the lens of human and experimental animals (cows, dogs, rats, rabbits) have been analyzed in various studies. In most cases, the studies employed different methods to determine the gross (total) composition of chemical elements and their concentrations in the examined samples. Less frequently, they included an assessment of the distribution of chemical elements in the lens and correlation of their concentration with its morphological changes. Chemical elements from all groups (series) of the periodic classification system were discovered in the lens substance. Despite similar investigation methods, different authors obtained contradicting results on the chemical composition of the lens. This article presents data suggesting possible correlation between inorganic chemical elements in the lens substance with the development and formation of lenticular opacities. All currently employed methods are known to only analyze limited number of select chemical elements in the tissues and do not consider the whole range of elements that can be analyzed with existing technology; furthermore, the majority of studies are conducted on the animal model lens. Therefore, it is feasible to continue the development of the chemical microanalysis method by increasing the sensitivity of Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEM/EDS) with the purpose of assessing the gross chemical composition and distribution of the elements in the lens substance, as well as revealing possible correlation between element concentration and morphological changes in the lens.

Modeling strength loss in wood by chemical composition. Part I, An individual component model for southern pine

Treesearch

J. E. Winandy; P. K. Lebow

2001-01-01

In this study, we develop models for predicting loss in bending strength of clear, straight-grained pine from changes in chemical composition. Although significant work needs to be done before truly universal predictive models are developed, a quantitative fundamental relationship between changes in chemical composition and strength loss for pine was demonstrated. In...

Adsorption behaviour of hydrogarnet for humic acid

NASA Astrophysics Data System (ADS)

Maeda, Hirotaka; Kurosaki, Yuichi; Nakayama, Masanobu; Ishida, Emile Hideki; Kasuga, Toshihiro

2018-04-01

Discharge of humic acid (HA) in aqueous environments is a key health and aesthetic issue. The present work investigates the use of hydrogarnet as a novel adsorbent for HA. Hydrogarnet was hydrothermally synthesized with different solvents to control the chemical composition. Hydrogarnet with three types of chemical compositions had better adsorption properties for HA than hydrogarnet with a single chemical composition. Controlling the chemical composition of hydrogarnet increased the number of hydroxyl groups and the overall binding energy of the system, leading to changes in the zeta potential. The enhancement of these adsorption properties is related to the increased numbers of hydroxyl groups on the surface and their diverse binding energies.

Evaluation of Beef by Electronic Tongue System TS-5000Z: Flavor Assessment, Recognition and Chemical Compositions According to Its Correlation with Flavor.

PubMed

Zhang, Xinzhuang; Zhang, Yawei; Meng, Qingxiang; Li, Ning; Ren, Liping

2015-01-01

The aim of this study was to assess the ability of electronic tongue system TS-5000Z to evaluate meat quality based on flavor assessment, recognition and correlation with the meat chemical composition. Meat was sampled from eighteen beef cattle including 6 Wagyu breed cattle, 6 Angus breed cattle and 6 Simmental breed cattle. Chemical composition including dry matter, crude protein, fat, ash, cholesterol and taurine and flavor of the meat were measured. The results showed that different breed cattle had different chemical compositions and flavor, which contains sourness, umami, saltiness, bitterness, astringency, aftertaste from astringency, aftertaste from bitterness and aftertaste from umami, respectively. A principal component analysis (PCA) showed an easily visible separation between different breeds of cattle and indicated that TS-5000Z made a rapid identification of different breeds of cattle. In addition, TS-5000Z seemed to be used to predict the chemical composition according to its correlation with the flavor. In conclusion, TS-5000Z would be used as a rapid analytical tool to evaluate the beef quality both qualitatively and quantitatively, based on flavor assessment, recognition and chemical composition according to its correlation with flavor.

Cometary coma chemical composition (C4) mission. [Abstract only

NASA Technical Reports Server (NTRS)

Carle, G. C.; Clark, B. C.; Niemann, H. B.; Alexander, M.; Knocke, P. C.; O'Hara, B. J.

1994-01-01

Cometary missions are of enormous fundamental importance for many different space science disciplines, including exobiology. Comets are presumed relics of the earliest, most primitive material in the solar nebula and are related to the planetesimals. They undoubtedly provided a general enrichment of volatiles to the inner solar system (contributing to atmospheres and oceans) and may have been key to the origin of life. A Discovery class, comet rendezvous mission, the Cometary Coma Chemical Composition (C4) Mission, was selected for further study by NASA earlier this year. The C4 Mission is a highly focused and usefully-limited subset of the Cometary Rendezvous Asteroid Flyby (CRAF) Mission, concentrating exclusively on measurements which will lead to an understanding of the chemical composition and make-up of the cometary nucleus. The scientific goals of the Cometary Coma Chemical Composition (C4) Mission are to rendezvous with a short-period comet and (1) to determine the elemental, chemical, and isotopic composition of the nucleus and (2) to characterize the chemical and isotopic nature of its atmosphere. Further, it is a goal to obtain preliminary data on the development of the coma (dust and gas composition) as a function of time and orbital position.

Catalytic Conversion of Carbohydrates to Initial Platform Chemicals: Chemistry and Sustainability.

PubMed

Mika, László T; Cséfalvay, Edit; Németh, Áron

2018-01-24

The replacement of fossil resources that currently provide more than 90% of our energy needs and feedstocks of the chemical industry in combination with reduced emission of carbon dioxide is one of the most pressing challenges of mankind. Biomass as a globally available resource has been proposed as an alternative feedstock for production of basic building blocks, which could partially or even fully replace the currently utilized fossil-based ones in well-established chemical processes. The destruction of lignocellulosic feed followed by oxygen removal from its cellulose and hemicellulose content by catalytic processes results in the formation of initial platform chemicals (IPCs). However, their sustainable production strongly depends on the availability of resources, their efficient or even industrially viable conversion processes, and replenishment time of feedstocks. Herein, we overview recent advances and developments in catalytic transformations of the carbohydrate content of lignocellulosic biomass to IPCs (i.e., ethanol, 3-hydroxypropionic acid, isoprene, succinic and levulinic acids, furfural, and 5-hydroxymethylfurfural). The mechanistic aspects, development of new catalysts, different efficiency indicators (yield and selectivity), and conversion conditions of their production are presented and compared. The potential biochemical production routes utilizing recently engineered microorganisms are reviewed, as well. The sustainability metrics that could be applied to the chemical industry (individual set of sustainability indicators, composite indices methods, material and energy flow analysis-based metrics, and ethanol equivalents) are also overviewed as well as an outlook is provided to highlight challenges and opportunities associated with this huge research area.

[The characteristics of chemical composition of content of unicameral bone cysts depending on their growth stage].

PubMed

Stogov, M V; Luneva, S N; Mitrofanov, A I; Tkachuk, E A

2012-11-01

The article deals with the results of study of chemical composition of solitary cysts and blood serum of 27 patients. The results demonstrated that qualitative composition of f content of unicameral bone cysts is identical to chemical composition of blood serum. The results of analysis of total proteolysis activity and acid phosphatase activity in content of cysts can be used as criteria to determine the stage of cyst growth and to evaluate the effectiveness of applied treatment.

40 CFR 79.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... combustion or other chemical or physical reaction. (d) Fuel manufacturer means any person who, for sale or... the chemical composition of a bulk fuel, or the mixture of chemical compounds in a bulk fuel, by... fuel. (h) Chemical composition means the name and percentage by weight of each compound in an additive...

Prediction of the true digestible amino acid contents from the chemical composition of sorghum grain for poultry.

PubMed

Ebadi, M R; Sedghi, M; Golian, A; Ahmadi, H

2011-10-01

Accurate knowledge of true digestible amino acid (TDAA) contents of feedstuffs is necessary to accurately formulate poultry diets for profitable production. Several experimental approaches that are highly expensive and time consuming have been used to determine available amino acids. Prediction of the nutritive value of a feed ingredient from its chemical composition via regression methodology has been attempted for many years. The artificial neural network (ANN) model is a powerful method that may describe the relationship between digestible amino acid contents and chemical composition. Therefore, multiple linear regressions (MLR) and ANN models were developed for predicting the TDAA contents of sorghum grain based on chemical composition. A precision-fed assay trial using cecectomized roosters was performed to determine the TDAA contents in 48 sorghum samples from 12 sorghum varieties differing in chemical composition. The input variables for both MLR and ANN models were CP, ash, crude fiber, ether extract, and total phenols whereas the output variable was each individual TDAA for every sample. The results of this study revealed that it is possible to satisfactorily estimate the TDAA of sorghum grain through its chemical composition. The chemical composition of sorghum grain seems to highly influence the TDAA contents when considering components such as CP, crude fiber, ether extract, ash and total phenols. It is also possible to estimate the TDAA contents through multiple regression equations with reasonable accuracy depending on composition. However, a more satisfactory prediction may be achieved via ANN for all amino acids. The R(2) values for the ANN model corresponding to testing and training parameters showed a higher accuracy of prediction than equations established by the MLR method. In addition, the current data confirmed that chemical composition, often considered in total amino acid prediction, could be also a useful predictor of true digestible values of selected amino acids for poultry.

Reflecting on the Liberal Reflex: Rhetoric and the Politics of Acknowledgement in Basic Writing

ERIC Educational Resources Information Center

Pavesich, Matthew

2011-01-01

In the 1990s, leading rhetoric and composition scholars criticized basic writing programs for their "liberalism." Basic writing had its defenders, however, and the ensuing debate exposed deep rifts in the field. This article argues that neither side in this formative debate nor the more recent alternative models of teaching basic writing…

Finite-deformation phase-field chemomechanics for multiphase, multicomponent solids

NASA Astrophysics Data System (ADS)

Svendsen, Bob; Shanthraj, Pratheek; Raabe, Dierk

2018-03-01

The purpose of this work is the development of a framework for the formulation of geometrically non-linear inelastic chemomechanical models for a mixture of multiple chemical components diffusing among multiple transforming solid phases. The focus here is on general model formulation. No specific model or application is pursued in this work. To this end, basic balance and constitutive relations from non-equilibrium thermodynamics and continuum mixture theory are combined with a phase-field-based description of multicomponent solid phases and their interfaces. Solid phase modeling is based in particular on a chemomechanical free energy and stress relaxation via the evolution of phase-specific concentration fields, order-parameter fields (e.g., related to chemical ordering, structural ordering, or defects), and local internal variables. At the mixture level, differences or contrasts in phase composition and phase local deformation in phase interface regions are treated as mixture internal variables. In this context, various phase interface models are considered. In the equilibrium limit, phase contrasts in composition and local deformation in the phase interface region are determined via bulk energy minimization. On the chemical side, the equilibrium limit of the current model formulation reduces to a multicomponent, multiphase, generalization of existing two-phase binary alloy interface equilibrium conditions (e.g., KKS). On the mechanical side, the equilibrium limit of one interface model considered represents a multiphase generalization of Reuss-Sachs conditions from mechanical homogenization theory. Analogously, other interface models considered represent generalizations of interface equilibrium conditions consistent with laminate and sharp-interface theory. In the last part of the work, selected existing models are formulated within the current framework as special cases and discussed in detail.

Chemical processing of glasses

NASA Astrophysics Data System (ADS)

Laine, Richard M.

1990-11-01

The development of chemical processing methods for the fabrication of glass and ceramic shapes for photonic applications is frequently Edisonian in nature. In part, this is because the numerous variables that must be optimized to obtain a given material with a specific shape and particular properties cannot be readily defined based on fundamental principles. In part, the problems arise because the basic chemistry of common chemical processing systems has not been fully delineated. The prupose of this paper is to provide an overview of the basic chemical problems associated with chemical processing. The emphasis will be on sol-gel processing, a major subset pf chemical processing. Two alternate approaches to chemical processing of glasses are also briefly discussed. One approach concerns the use of bimetallic alkoxide oligomers and polymers as potential precursors to mulimetallic glasses. The second approach describes the utility of metal carboxylate precursors to multimetallic glasses.

Organic-inorganic hybrid lead halide perovskites for optoelectronic and electronic applications.

PubMed

Zhao, Yixin; Zhu, Kai

2016-02-07

Organic and inorganic hybrid perovskites (e.g., CH(3)NH(3)PbI(3)), with advantages of facile processing, tunable bandgaps, and superior charge-transfer properties, have emerged as a new class of revolutionary optoelectronic semiconductors promising for various applications. Perovskite solar cells constructed with a variety of configurations have demonstrated unprecedented progress in efficiency, reaching about 20% from multiple groups after only several years of active research. A key to this success is the development of various solution-synthesis and film-deposition techniques for controlling the morphology and composition of hybrid perovskites. The rapid progress in material synthesis and device fabrication has also promoted the development of other optoelectronic applications including light-emitting diodes, photodetectors, and transistors. Both experimental and theoretical investigations on organic-inorganic hybrid perovskites have enabled some critical fundamental understandings of this material system. Recent studies have also demonstrated progress in addressing the potential stability issue, which has been identified as a main challenge for future research on halide perovskites. Here, we review recent progress on hybrid perovskites including basic chemical and crystal structures, chemical synthesis of bulk/nanocrystals and thin films with their chemical and physical properties, device configurations, operation principles for various optoelectronic applications (with a focus on solar cells), and photophysics of charge-carrier dynamics. We also discuss the importance of further understanding of the fundamental properties of hybrid perovskites, especially those related to chemical and structural stabilities.

Effect of alkaline treatment on mechanical properties of kenaf fiber reinforced polyester composites

NASA Astrophysics Data System (ADS)

Reddy, Bijjam Ramgopal; Dhoria, Sneha H.

2018-04-01

This paper focuses on the study of the effect of chemical treatment on mechanical properties such as tensile, flexural and impact properties of kenaf fiber reinforced polyester composites. Adhesion between the fiber and polymer is one of factors affecting the mechanical properties of composites. In order to increase the adhesion, the fibers are chemically treated with 5% of sodium hydroxide (NaOH) solution. The composite specimens are prepared in both untreated and treated forms of kenaf fibers with five levels of fiber volume fractions. The specimens are prepared according to ASTM standards. Mechanical tests such as tensile, flexural and impact are conducted to determine ultimate tensile strength, bending strength and impact strength of composites. The effect of change in volume fraction on the mechanical properties of the composites is studied for both untreated (raw) and chemically treated kenaf fibers. It has been found that the composites made of chemically treated fibers have good mechanical properties compared to untreated fibers.

Bulk chemical compositions of Antarctic meteorites in the NIPR collection

NASA Astrophysics Data System (ADS)

Kimura, M.; Imae, N.; Yamaguchi, A.; Haramura, H.; Kojima, H.

2018-03-01

Bulk chemical compositions of meteorites were traditionally analyzed by wet chemical analysis, and NIPR has data for 1162 meteorites as of September 2017. We discuss the classification of meteorites on the basis of these data. Chondrite data are distributed in an anomalously wide range of compositions on the Urey-Craig diagram. One of the reasons for such wide distribution is terrestrial weathering producing Fe2O3-bearing phases from Fe-Ni metal and sulfides. Another important factor affecting the bulk compositional data is brecciation. Our observations indicate that many brecciated chondrites contain anomalously abundant opaque minerals, or are depleted in them, resulting in unusual compositions. In case of enstatite and some carbonaceous chondrites, the bulk compositions are distributed in wider ranges than reported before. The bulk compositions of HED meteorites are consistent with their mineralogy and classification. Our study suggests that wet chemical data are still significant for the meteorite classification. However, petrographic observation is indispensable for evaluating the bulk chemistry and classification of meteorites.

75 FR 26049 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-10

... conducted by ``a licensed professional engineer or foreign equivalent who works in the chemical engineering... chemical engineering field. EPA views renewable fuel production to fall generally within the chemical... basic organic chemical manufacturers. Industry 424690 5169 Chemical and allied products merchant...

High-School Students' Conceptual Difficulties and Attempts at Conceptual Change: The Case of Basic Quantum Chemical Concepts

ERIC Educational Resources Information Center

Tsaparlis, Georgios; Papaphotis, Georgios

2009-01-01

This study tested for deep understanding and critical thinking about basic quantum chemical concepts taught at 12th grade (age 17-18). Our aim was to achieve conceptual change in students. A quantitative study was conducted first (n = 125), and following this 23 selected students took part in semi-structured interviews either individually or in…

An alternative approach to the Boltzmann distribution through the chemical potential

NASA Astrophysics Data System (ADS)

D'Anna, Michele; Job, Georg

2016-05-01

The Boltzmann distribution is one of the most significant results of classical physics. Despite its importance and its wide range of application, at high school level it is mostly presented without any derivation or link to some basic ideas. In this contribution we present an approach based on the chemical potential that allows to derive it directly from the basic idea of thermodynamical equilibrium.

JPRS Report, China, Handbook of Military Knowledge for Commanders

DTIC Science & Technology

1988-03-07

Chemical and Biological Weapons Chapter I Nuclear Weapons (178) A. Summary Statement on Nuclear Weapons (178) 1. Basic Principles of Nuclear...199) 1. Basic Principles of Protection Against Nuclear, Chemical and Biological Weapons* (199) 2. Maior Actions For Protection Against Nuclear...people’s bodies through the digestive tract. Skin contact. Biological warfare agents may enter the body directly through the skin , mucous membranes or

Basic Information for the Review of New Chemicals

EPA Pesticide Factsheets

Mandated by section 5 of the Toxic Substances Control Act (TSCA), EPA's New Chemicals program helps manage the potential risk to human health and the environment from chemicals new to the marketplace.

Regular patterns of Cs-137 distribution in natural conjugated elementary landscapes as a result of a balanced surface and depth water migration

NASA Astrophysics Data System (ADS)

Korobova, Elena; Romanov, Sergey

2016-04-01

Distribution of artificial radionuclides in the environment has long been used successfully for revealing migration pathways of their stable analogues. Migration of water in natural conjugated elementary landscapes characterizing the system of top-slope-resulting depression, has a specific structure and the radionuclide tracer is inevitably reflecting it by specific sorption and exchange processes. Other important issues are the concentration levels and the difference in characteristic time of chemical element dispersion. Modern biosphere has acquired its sustainable structure within a long period of time and is formed by basic macroelements allowing the water soluble portion of elements functioning as activators of chemical exchange. Water migration is controlled by gravitation, climate and relief while fixation depends upon the parameters of surfaces and chemical composition. The resulting structure depends on specificity and duration of the process. The long-term redistribution of chemical elements in terrestrial environment has led to a distinct geochemical structure of conjugated landscapes with a specific geometry of redistribution and accumulation of chemical elements. Migration of the newly born anthropogenic radionuclides followed natural pathways in biosphere. The initial deposition of the Chernobyl's radionuclides within the elementary landscape-geochemical system was even by condition of aerial deposition. But further exchange process is controlled by the strength of fixation and migration ability of the carriers. Therefore patterns of spatial distribution of artificial radionuclides in natural landscapes are considerably different as compared to those of the long-term forming the basic structure of chemical fields in biosphere. Our monitoring of Cs-137 radial and lateral distribution in the test plots characterizing natural undisturbed conjugated elementary landscapes performed in the period from 2005 until now has revealed a stable and specifically polycentric structure of radiocesium distribution believed to reflect the character of radial and lateral water body migration and a high sensitivity of water distribution to surface parameters. This leads to an unusual wavy type of Cs-137 distribution down, along and across all the slopes examined for surface Cs-137 activity at every measured point. The finding is believed to have an important practical outcome allowing much more detailed evaluation of micronutrients distribution and optimization of their application.

Chemical composition of stars in Ruprecht 106 .

NASA Astrophysics Data System (ADS)

François, P.

High resolution spectra of 9 stars belonging to the globular cluster Rup 106 have been used to determine their chemical composition. The results reveal that Ruprecht 106 exhibits abundance anomalies when compared to galactic globular cluster of similar metallicity. The chemical composition of these stars is similar to what is found in Dwarf spheroidal galaxies favoring the hypothesis that Rup 106 has not been formed in our Galaxy.

Evaluating the influence of chemical weathering on the composition of the continental crust using lithium and its isotopes

NASA Astrophysics Data System (ADS)

Rudnick, R. L.; Liu, X.

2011-12-01

The continental crust has an "intermediate" bulk composition that is distinct from primary melts of peridotitic mantle (basalt or picrite). This mismatch between the "building blocks" and the "edifice" of the continental crust points to the operation of processes that preferentially remove mafic to ultramafic material from the continents. Such processes include lower crustal recycling (via density foundering or lower crustal subduction - e.g., relamination, Hacker et al., 2011, EPSL), generation of evolved melts via slab melting, and/or chemical weathering. Stable isotope systems document the influence of chemical weathering on the bulk crust composition: the oxygen isotope composition of the bulk crust is distinctly heavier than that of primary, mantle-derived melts (Simon and Lecuyer, 2005, G-cubed) and the Li isotopic composition of the bulk crust is distinctly lighter than that of mantle-derive melts (Teng et al., 2004, GCA; 2008, Chem. Geol.). Both signatures mark the imprint of chemical weathering on the bulk crust composition. Here, we use a simple mass balance model for lithium inputs and outputs from the continental crust to quantify the mass lost due to chemical weathering. We find that a minimum of 15%, a maximum of 60%, and a best estimate of ~40% of the original juvenile rock mass may have been lost via chemical weathering. The accumulated percentage of mass loss due to chemical weathering leads to an average global chemical weathering rate (CWR) of ~ 8×10^9 to 2×10^10 t/yr since 3.5 Ga, which is about an order of magnitude higher than the minimum estimates based on modern rivers (Gaillardet et al., 1999, Chem. Geol.). While we cannot constrain the exact portion of crustal mass loss via chemical weathering, given the uncertainties of the calculation, we can demonstrate that the weathering flux is non-zero. Therefore, chemical weathering must play a role in the evolution of the composition and mass of the continental crust.

Prediction of Combustion Gas Deposit Compositions

NASA Technical Reports Server (NTRS)

Kohl, F. J.; Mcbride, B. J.; Zeleznik, F. J.; Gordon, S.

1985-01-01

Demonstrated procedure used to predict accurately chemical compositions of complicated deposit mixtures. NASA Lewis Research Center's Computer Program for Calculation of Complex Chemical Equilibrium Compositions (CEC) used in conjunction with Computer Program for Calculation of Ideal Gas Thermodynamic Data (PAC) and resulting Thermodynamic Data Base (THDATA) to predict deposit compositions from metal or mineral-seeded combustion processes.

Update on the Chemical Composition Of Crystalline, Smectite, and Amorphous Components for Rocknest Soil and John Klein and Cumberland Mudstone Drill Fines at Gale Crater, Mars

NASA Technical Reports Server (NTRS)

Morris, R. V.; Ming, D. W.; Gellert, R.; Vaniman, D. T.; Bish, D. L.; Blake, D. F.; Chipera, S. J.; Morrison, S. M.; Downs, R. T.; Rampe, E. B.;

Correlation of rocket propulsion fuel properties with chemical composition using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry followed by partial least squares regression analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kehimkar, Benjamin; Hoggard, Jamin C.; Marney, Luke C.

There is an increased need to more fully assess and control the composition of kerosene based rocket propulsion fuels, namely RP-1 and RP-2. In particular, it is crucial to be able to make better quantitative connections between the following three attributes: (a) fuel performance, (b) fuel properties (flash point, density, kinematic viscosity, net heat of combustion, hydrogen content, etc) and (c) the chemical composition of a given fuel (i.e., specific chemical compounds and compound classes present as a result of feedstock blending and processing). Indeed, recent efforts in predicting fuel performance through modeling put greater emphasis on detailed and accuratemore » fuel properties and fuel compositional information. In this regard, advanced distillation curve (ADC) metrology provides improved data relative to classical boiling point and volatility curve techniques. Using ADC metrology, data obtained from RP-1 and RP-2 fuels provides compositional variation information that is directly relevant to predictive modeling of fuel performance. Often, in such studies, one-dimensional gas chromatography (GC) combined with mass spectrometry (MS) is typically employed to provide chemical composition information. Building on approaches using GC-MS, but to glean substantially more chemical composition information from these complex fuels, we have recently studied the use of comprehensive two dimensional gas chromatography combined with time-of-flight mass spectrometry (GC × GC - TOFMS) to provide chemical composition data that is significantly richer than that provided by GC-MS methods. In this report, by applying multivariate data analysis techniques, referred to as chemometrics, we are able to readily model (correlate) the chemical compositional information from RP-1 and RP-2 fuels provided using GC × GC - TOFMS, to the fuel property information such as that provided by the ADC method and other specification properties. We anticipate that this new chemical analysis strategy will have broad implications for the development of high fidelity composition-property models, leading to an optimized approach to fuel formulation and specification for advanced engine cycles.« less

Exploring, tuning, and exploiting the basicity of hydrotalcites for applications in heterogeneous catalysis.

PubMed

Debecker, Damien P; Gaigneaux, Eric M; Busca, Guido

2009-01-01

Basic catalysis! The basic properties of hydrotalcites (see picture) make them attractive for numerous catalytic applications. Probing the basicity of the catalysts is crucial to understand the base-catalysed processes and to optimise the catalyst preparation. Various parameters can be employed to tune the basic properties of hydrotalcite-based catalysts towards the basicity demanded by each target chemical reaction.Hydrotalcites offer unique basic properties that make them very attractive for catalytic applications. It is of primary interest to make use of accurate tools for probing the basicity of hydrotalcite-based catalysts for the purpose of 1) fundamental understanding of base-catalysed processes with hydrotalcites and 2) optimisation of the catalytic performance achieved in reactions of industrial interest. Techniques based on probe molecules, titration techniques and test reactions along with physicochemical characterisation are overviewed in the first part of this review. The aim is to provide the tools for understanding how series of parameters involved in the preparation of hydrotalcite-based catalytic materials can be employed to control and adapt the basic properties of the catalyst towards the basicity demanded by each target chemical reaction. An overview of recent and significant achievements in that perspective is presented in the second part of the paper.

Self-repair of cracks in brittle material systems

NASA Astrophysics Data System (ADS)

Dry, Carolyn M.

2016-04-01

One of the most effective uses for self repair is in material systems that crack because the cracks can allow the repair chemical to flow into the crack damage sites in all three dimensions. In order for the repair chemical to stay in the damage site and flow along to all the crack and repair there must be enough chemical to fill the entire crack. The repair chemical must be designed appropriately for the particular crack size and total volume of cracks. In each of the three examples of self repair in crackable brittle systems, the viscosity and chemical makeup and volume of the repair chemicals used is different for each system. Further the chemical delivery system has to be designed for each application also. Test results from self repair of three brittle systems are discussed. In "Self Repair of Concrete Bridges and Infrastructure" two chemicals were used due to different placements in bridges to repair different types of cracks- surface shrinkage and shear cracks, In "Airplane Wings and Fuselage, in Graphite" the composite has very different properties than the concrete bridges. In the graphite for airplane components the chemical also had to survive the high processing temperatures. In this composite the cracks were so definite and deep and thin that the repair chemical could flow easily and repair in all layers of the composite. In "Ceramic/Composite Demonstrating Self Repair" the self repair system not only repaired the broken ceramic but also rebounded the composite to the ceramic layer

Data on the weights, specific gravities and chemical compositions of potato (Solanum tuberosum) tubers for food processing from different areas of Hokkaido, Japan.

PubMed

Sato, Hiroaki; Koizumi, Ryosuke; Nakazawa, Yozo; Yamazaki, Masao; Itoyama, Ryuichi; Ichisawa, Megumi; Negichi, Junko; Sakuma, Rui; Furusho, Tadasu; Sagane, Yoshimasa; Takano, Katsumi

2017-04-01

This data article provides the weights, specific gravities and chemical compositions (moisture, protein, fat, ash, and carbohydrate) of potato tubers, for food processing use, from the Tokachi, Kamikawa and Abashiri areas of Hokkaido, Japan. Potato tubers of four cultivars ('Toyoshiro', 'Kitahime', 'Snowden' and 'Poroshiri') were employed in the current study. The weights and specific gravities of potato tubers from each cultivar, harvested from three areas, were measured, and those of near average weight and specific gravity from each group were analyzed for their chemical composition. In this article, weight, specific gravity, and chemical composition data are provided in tables.

Composite-Material Point-Stress Analysis

NASA Technical Reports Server (NTRS)

Spears, F., S.

1982-01-01

PSANAL computes composite-laminate elastic and thermal properties and allowable load levels for any combination of applied membrane and bending loads occurring at a point. Basic linear orthotropic stress/ strain relationships and standard composite-laminate theory formulas are utilized.

Chemical composition, nutritional value and antioxidant properties of Mediterranean okra genotypes in relation to harvest stage.

PubMed

Petropoulos, Spyridon; Fernandes, Ângela; Barros, Lillian; Ferreira, Isabel C F R

2018-03-01

The aim of the present study was to determine the effect of fruit size on nutritional value, chemical composition and antioxidant properties of Mediterranean okra genotypes. For this purpose, pods from four okra cultivars and local landraces commonly cultivated in Greece, as well as pods from four commercial cultivars from North America were collected at two sizes (3-5 and>7cm). Significant differences were observed between the studied genotypes for both nutritional value and chemical composition parameters. Small fruit had a higher nutritional value, whereas chemical composition differed in a genotype dependent manner with most of the studied cultivars showing better results when harvested in small size. In conclusion, fruit size has a genotype dependent impact on chemical composition and nutritional value of okra pods and the common practice of harvesting okra fruit while they still have a small size helps to increase nutritional value for most of the studied genotypes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mineralogy, petrology and geochemistry of carbonaceous chondritic clasts in the LEW 85300 polymict eucrite

NASA Technical Reports Server (NTRS)

Zolensky, M. E.; Hewins, R. H.; Mittlefehldt, D. W.; Lindstrom, M. M.; Xiao, X.; Lipschutz, M. E.

1992-01-01

We have performed a detailed petrologic and mineralogic study of two chondritic clasts from the polymict eucrite Lewis Cliff (LEW) 85300, and performed chemical analyses by INAA and RNAA on one of these. Petrologically, the clasts are identified and are composed of dispersed aggregates, chondrules, and chondrule fragments supported by matrix. The aggregates and chondrules are composed of olivine, orthopyroxene, plus some diopside. The matrix consists of fine-grained olivine, and lesser orthopyroxene and augite. Fine-grained saponite is common in the matrix. The bulk major composition of the clast studied by INAA and RNAA shows unusual abundance patterns for lithophile, siderophile and chalcophile elements but is basically chondritic. The INAA/RNAA data preclude assignment of the LEW 85300,15 clast to any commonly accepted group of carbonaceous chondrite.

Electron Density Calibration for Radiotherapy Treatment Planning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herrera-Martinez, F.; Rodriguez-Villafuerte, M.; Martinez-Davalos, A.

2006-09-08

Computed tomography (CT) images are used as basic input data for most modern radiosurgery treatment planning systems (TPS). CT data not only provide anatomic information to delineate target volumes, but also allow the introduction of corrections for tissue inhomogeneities into dose calculations during the treatment planning procedure. These corrections involve the determination of a relationship between tissue electron density ({rho}e) and their corresponding Hounsfield Units (HU). In this work, an elemental analysis of different commercial tissue equivalent materials using Scanning Electron Microscopy was carried out to characterize their chemical composition. The tissue equivalent materials were chosen to ensure a largemore » range of {rho}e to be included in the CT scanner calibration. A phantom was designed and constructed with these materials to simulate the size of a human head.« less

Characterizing Exoplanet Atmospheres with the James Webb Space Telescope

NASA Technical Reports Server (NTRS)

Greene, Tom

2017-01-01

The James Webb Space Telescope (JWST) will have numerous modes for acquiring photometry and spectra of stars, planets, galaxies, and other astronomical objects over wavelengths of 0.6 - 28 microns. Several of these modes are well-suited for observing atomic and molecular features in the atmospheres of transiting or spatially resolved exoplanets. I will present basic information on JWST capabilities, highlight modes that are well-suited for observing exoplanets, and give examples of what may be learned from JWST observations. This will include simulated spectra and expected retrieved chemical abundance, composition, equilibrium, and thermal information and uncertainties. JWST Cycle 1 general observer proposals are expected to be due in March 2018 with launch in October 2018, and the greater scientific community is encouraged to propose investigations to study exoplanet atmospheres and other topics.

Feasibility of Using Dredged Mud for Prepared the Permeable Brick

NASA Astrophysics Data System (ADS)

Zhou, Chaoqun; Cheng, Xiaosu; Zeng, Lingke; Wang, Hui; Chen, Jing

2017-10-01

Through experimental analysis found that the chemical composition of the dredged mud is similar to clay and the dredged mud does not leach heavy metals. Using the dredged mud in the preparation of permeable bricks reduced the quantity of incineration dredged mud buried in landfills, and the exploitation and consumption of natural sandstone. The dredged mud needs to be checked by the validation criteria when the second use, so we used the TCLP test to identify hazardous materials. Its leaching of heavy metals was in line with industry standard. And the basic formula of permeable brick were prepared, its performance was in line with national standards. The use of dredged mud preparing eco-friendly permeable bricks, not only solves the problem of environmental pollution, but also gets some economic and social profit.

Effects of gravity on contractile proteins

NASA Technical Reports Server (NTRS)

Henney, H. R., Jr.

1979-01-01

A method was established for the isolation and purification of nuclei in high yield from the microplasmodia of Physarum flavicomum. Purified nuclei were resistant to breakage by methods commonly employed for isolated plant and animal nuclei. Several methods for the extraction of nuclear protein were compared. Incubation of nuclear lysates with either 2 M NaCl, with or without 5 M urea, or 1 M CaCl2 resulted in the extraction of nuclear action together with histones. The histones were chemically fractionated into the 5 basic groups common to other eucaryotic tissue. Amino acid analyses of the total histone were also performed. Nuclear actin was found to have a molecular weight of 41,000 ? 4,000 daltons as determined by SDS polyacrylamide gel electrophoresis. The amino acid composition of the nuclear action was established.

Investigations of Archaeological Glass Bracelets and Perfume Bottles Excavated in Ancient Ainos (Enez) by Multiple Analytical Techniques

NASA Astrophysics Data System (ADS)

Celik, S.; Akyuz, T.; Akyuz, S.; Ozel, A. E.; Kecel-Gunduz, S.; Basaran, S.

2018-03-01

Fragments of two perfume bottles belonging to the Hellenistic and Roman periods, and five bracelets belonging to the Roman, Byzantine, and Ottoman periods, excavated in the archaeological site of Enez during the excavations in 2000, have been investigated. The samples were analyzed using micro-Raman, FTIR, and energy dispersive X-ray fluorescence techniques, in order to study the ancient technology of glass production and to determine chemical compositions of the basic components and coloring elements of the glassware. All the investigated glasses can be characterized as low-magnesia-soda-lime silicate glasses, whose colors are induced by metal ions. The melting points of the investigated glasses are estimated to be quite close to each other and around 1000°C.

Catalytic deoxygenation of microalgae oil to green hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Chen; Bruck, Thomas; Lercher, Johannes A.

2013-05-14

Microalgae are high potential raw biomass material for triglyceride feedstock, due to their high oil content and rapid growth rate, and because algae cultivation does not compete with edible food on arable land. This review addresses first the microalgae cultivation with an overview of the productivity and growth of microalgae, the recovery of lipids from the microalgae, and chemical compositions of microalgae biomass and microalgal oil. Second, three basic approaches are discussed to downstream processing for the production of green gasoline and diesel hydrocarbons from microalgae oil, including cracking with zeolite, hydrotreating with supported sulfided catalysts and hydrodeoxygenation with non-sulfidemore » metal catalysts. For the triglyceride derived bio-fuels, only “drop-in” gasoline and diesel range components are discussed in this review.« less

Software for analysis of chemical mixtures--composition, occurrence, distribution, and possible toxicity

USGS Publications Warehouse

Scott, Jonathon C.; Skach, Kenneth A.; Toccalino, Patricia L.

2013-01-01

The composition, occurrence, distribution, and possible toxicity of chemical mixtures in the environment are research concerns of the U.S. Geological Survey and others. The presence of specific chemical mixtures may serve as indicators of natural phenomena or human-caused events. Chemical mixtures may also have ecological, industrial, geochemical, or toxicological effects. Chemical-mixture occurrences vary by analyte composition and concentration. Four related computer programs have been developed by the National Water-Quality Assessment Program of the U.S. Geological Survey for research of chemical-mixture compositions, occurrences, distributions, and possible toxicities. The compositions and occurrences are identified for the user-supplied data, and therefore the resultant counts are constrained by the user’s choices for the selection of chemicals, reporting limits for the analytical methods, spatial coverage, and time span for the data supplied. The distribution of chemical mixtures may be spatial, temporal, and (or) related to some other variable, such as chemical usage. Possible toxicities optionally are estimated from user-supplied benchmark data. The software for the analysis of chemical mixtures described in this report is designed to work with chemical-analysis data files retrieved from the U.S. Geological Survey National Water Information System but can also be used with appropriately formatted data from other sources. Installation and usage of the mixture software are documented. This mixture software was designed to function with minimal changes on a variety of computer-operating systems. To obtain the software described herein and other U.S. Geological Survey software, visit http://water.usgs.gov/software/.

Thickness limitations in carbon nanotube reinforced silicon nitride coatings synthesized by vapor infiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eres, Gyula

Chemical vapor infiltration is a convenient method for synthesizing carbon nanotube (CNT)-reinforced ceramic coatings. The thickness over which infiltration is relatively uniform is limited by gas phase diffusion in the pore structure. These effects were investigated in two types of silicon nitride matrix composites. With CNTs that were distributed uniformly on the substrate surface dense coatings were limited to thicknesses of several microns. With dual structured CNT arrays produced by photolithography coatings up to 400 gm thick were obtained with minimal residual porosity. Gas transport into these dual structured materials was facilitated by creating micron sized channels between "CNT pillars"more » (i.e. each pillar consisted of a large number of individual CNTs). The experimental results are consistent with basic comparisons between the rates of gas diffusion and silicon nitride growth in porous structures. This analysis also provides a general insight into optimizing infiltration conditions during the fabrication of thick CNT-reinforced composite coatings. (C) 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.« less

Determining the relative extent of alteration in CM chondrites

NASA Technical Reports Server (NTRS)

Browning, Lauren B.; Mcsween, Harry Y., Jr.; Zolensky, Michael

1993-01-01

The aqueous alteration of CM chondrites provides a record of the processes attending the earliest stages of parent body evolution. However, resolving the alteration pathways of chondritic evolution requires a means for distinguishing the relative extent of alteration that individual samples have experienced. Three new indices for gauging the relative degree of alteration in CM chondrites based on modal and compositional analyses of 7 CM falls were proposed. The proposed alteration parameters are consistent with the basic tenets of several previous models and correlate with additional indices to produce an integrated method for determining the relative extent of alteration. The model predicts the following order of progressive alteration: Murchison (MC) is less than or equal to Bells (BL) is less than Murray (MY) is less than Cochabamba (CC) is less than Mighei (MI) is less than Nogoya (NG) is less than or equal to Cold Bokkeveld (CB). The broad range of CM phyllosilicate compositions observed within individual meteorites is fundamental to the characterization of the aqueous alteration process. Chemical analyses of CM phyllosilicates suggest that these phases became systematically enriched in Mg and depleted in Fe with increasing alteration.

Biochar-supported reduced graphene oxide composite for adsorption and coadsorption of atrazine and lead ions

NASA Astrophysics Data System (ADS)

Zhang, Ying; Cao, Bo; Zhao, Lulu; Sun, Lili; Gao, Yan; Li, Jiaojiao; Yang, Fan

2018-01-01

To explore potential in application for simultaneous removal of atrazine and lead ions (Pd2+), the adsorption and coadsorption of atrazine and Pd2+ is evaluated onto a novel biochar-supported reduced graphene oxide composite (RGO-BC), which has been successfully developed via slow pyrolysis of graphene oxide (GO) pretreated corn straws. Structure and morphology analysis reveal that GO nanosheets are coated on the surface of biochar (BC) mainly through π-π interactions, notably, GO nanosheets after annealing reduction can basically retain the original morphology, meanwhile, the change of physico-chemical properties on the surface endow excellent adsorption capaities of 26.10 mg g-1 for Pb2+ and 67.55 mg g-1 for atrazine. A significant difference is in sorption of Pb2+ and atrazine on RGO-BC sample in both single- and binary-solute systems. The adsorption capacity of RGO-BC still remained above 54.58 mg g-1 after four times regeneration (81% adsorption capacity remained), demonstrating a promising candidate for the application of removal contaminant in the environment.

Study of the structure and chemical composition of the protective coating of a fist stage gas turbine blade after regenerative heat treatment

NASA Astrophysics Data System (ADS)

Davidov, D. I.; Kazantseva, N. V.; Vinogradova, N. I.; Ezhov, I. V.

2017-12-01

Investigation of the structure and chemical composition of the protective coating of the first stage IN738 gas turbine blade after standard regenerative heat treatment was done. It was found the degradation of microstructure and chemical composition of both the blade feather and its protective coating. Redistribution of the chemical elements decreasing the corrosion resistance was observed inside the protective coating. Cracks on the boundary between the blade feather and the protective coating were found by scanning electron microscopy. The carbide transformation and sigma phase were found in the structure of the blade feather. Based upon the structural and chemical composition studies, it is concluded that the standard regenerative heat treatment of the IN738 operative gas turbine blade does not provide full structure regeneration.

Statistical Analysis of CMC Constituent and Processing Data

NASA Technical Reports Server (NTRS)

Fornuff, Jonathan

2004-01-01

Ceramic Matrix Composites (CMCs) are the next "big thing" in high-temperature structural materials. In the case of jet engines, it is widely believed that the metallic superalloys currently being utilized for hot structures (combustors, shrouds, turbine vanes and blades) are nearing their potential limits of improvement. In order to allow for increased turbine temperatures to increase engine efficiency, material scientists have begun looking toward advanced CMCs and SiC/SiC composites in particular. Ceramic composites provide greater strength-to-weight ratios at higher temperatures than metallic alloys, but at the same time require greater challenges in micro-structural optimization that in turn increases the cost of the material as well as increases the risk of variability in the material s thermo-structural behavior. to model various potential CMC engine materials and examines the current variability in these properties due to variability in component processing conditions and constituent materials; then, to see how processing and constituent variations effect key strength, stiffness, and thermal properties of the finished components. Basically, this means trying to model variations in the component s behavior by knowing what went into creating it. inter-phase and manufactured by chemical vapor infiltration (CVI) and melt infiltration (MI) were considered. Examinations of: (1) the percent constituents by volume, (2) the inter-phase thickness, (3) variations in the total porosity, and (4) variations in the chemical composition of the Sic fiber are carried out and modeled using various codes used here at NASA-Glenn (PCGina, NASALife, CEMCAN, etc...). The effects of these variations and the ranking of their respective influences on the various thermo-mechanical material properties are studied and compared to available test data. The properties of the materials as well as minor changes to geometry are then made to the computer model and the detrimental effects observed using statistical analysis software. The ultimate purpose of this study is to determine what variations in material processing can lead to the most critical changes in the materials property. The work I have taken part in this summer explores, in general, the key properties needed In this study SiC/SiC composites of varying architectures, utilizing a boron-nitride (BN)

Chemical Composition of Four Shergottites from Northwest Africa (NWA 2800, NWA, 5214, NWA 5990, NWA 6342)

NASA Technical Reports Server (NTRS)

Yang, S.; Humayun, M.; Jefferson, G.; Fields, D.; Righter, K.; Irving, A. J.

2013-01-01

Shergottites represent the majority of recovered Martian meteorites. As basic igneous rocks, they formed from magmas that were emplaced in the Martian crust [1]. Due to the low ambient pressure of the Martian atmosphere, subaerial lavas and shallow magma chambers are expected to outgas volatile metals (e.g., Cd, Te, Re, Bi) [2]. The planetary abundances of the volatile siderophile and chalcophile elements are important at establishing the depth of core formation for Mars, and must be known as a baseline for understanding volcanic outgassing on Mars, particularly the large enrichments of S and Cl observed in modern Martian soils [3]. There is little data on volatile siderophile and chalcophile elements from Martian meteorites, excluding a few well-analyzed samples [2]. Further, a large number of shergottites being recovered from North West Africa are in need of chemical analysis. All of the shergottites are in need of state-of-the art analysis for such ratios as Ge/Si and Ga/Al, which can now be accomplished by LA-ICP-MS [2].

Mixed material formation and erosion

NASA Astrophysics Data System (ADS)

Linsmeier, Ch.; Luthin, J.; Goldstraß, P.

2001-03-01

The formation of mixed phases on materials relevant for first wall components of fusion devices is studied under well-defined conditions in ultra-high vacuum (UHV). This is necessary in order to determine fundamental parameters governing the basic processes of chemical reaction, material mixing and erosion. We examined the binary systems comprising of the wall materials beryllium, silicon, tungsten and titanium and carbon, the latter being both a wall material and a plasma impurity. Experiments were carried out to study the interaction of carbon in the form of a vapor-deposited component on clean, well-defined elemental surfaces. The chemical composition and the binding state are measured by X-ray photoelectron spectroscopy (XPS) after annealing treatments. For all materials, a limited carbide formation is found at room temperature. Annealing carbon films on elemental substrate leads to a complete carbidization of the carbon layer. The carbide layers on Be and Si are stable even at very high temperatures, whereas the carbides of Ti and W dissolve. The erosion of these two metals by sputtering is then identical to the pure metals, whereas for Be and Si a protective carbide layer can reduce the sputtering yields.

Trace organic compounds in wet atmospheric deposition: an overview

USGS Publications Warehouse

Steinheimer, T.R.; Johnson, S.M.

1987-01-01

An overview of the occurrence of organic compounds in wet atmospheric deposition is given. Multiplicity of sources and problems associated with source identification are discussed. Available literature is reviewed by using citations from Chemical Abstracts and Water Resources Abstracts through June 1985 and includes reports published through December 1984 that summarize current knowledge. Approaches to the chemical determination of organic compounds in precipitation are examined in addition to aspects of sampling protocols. Best methods for sample collection and preparation for instrumental analysis continue to be discussed among various investigators. Automatic wet-deposition-only devices for collection and extraction are preferred. Classes of organic compounds that have been identified in precipitation include a spectrum of compounds with differing properties of acidity or basicity, polarity, and water solubility. Those compounds that have been reported in rainfall, snowfall, and ice include hydrocarbons (both aromatic and nonaromatic), chlorinated derivatives of these hydrocarbons, carbonyl compounds (both acidic and nonacidic), and carboxylic acids and esters. Formic and acetic are the most abundant organic acids present. Cloudwater, fogwater, and mist also have been collected and analyzed for organic composition.

Correlation between some thermo-mechanical and physico-chemical properties in multi-component glasses of Se-Te-Sn-Cd system

NASA Astrophysics Data System (ADS)

Kumar, Amit; Mehta, Neeraj

2017-06-01

The glass transition phenomenon is guided by the swift cooling of a melt (glass-forming liquid). Consequently, the glass as a final product consists of a considerable number of micro-voids having the size of the order of atomic and/or molecular sizes. The model of free volume fluctuation helps in describing the diverse physico-chemical properties of amorphous materials (like glasses and polymers). This theory is based on the fraction of fluctuation free frozen at the glass transition temperature and it forms a basis for determination of various significant thermo-mechanical properties. In the present work, Vickers hardness test method is employed that provides useful information concerning the mechanical behavior of brittle solids. The present work emphasizes the results of micro-indentation measurements on recently synthesized novel Se78- x Te20Sn2Cd x glassy system. Basic thermo-mechanical parameters such as micro-hardness, volume ( V h), formation energy ( E h) of micro-voids in the glassy network and modulus of elasticity ( E) have been determined and their variation with glass composition has been investigated.

Development and implementation of the NMR-spectrometer on the basis of the National Instruments technologies

NASA Astrophysics Data System (ADS)

Narakidze, N. D.; Shaykhutdinov, D. V.; Shirokov, K. M.; Gorbatenko, N. I.; Yanvarev, S. G.

2017-02-01

The quality of lubricating oil in mechanical engineering, technology of creation of units, in particular in equipment of transmission gears, is a factor which considerably defines reliability and safety of the whole propulsion system or the greased constructive components. There are many soluble oil additives such as, for example, different additives for extreme compression conditions or additives against wear. Additives are used with mineral oils, products from mineral oils or synthetic oils for lubricant action or chemical properties improvement. The most exact way of definition of the chemical composition of a substance at the moment is the method of nuclear magnetic resonance (NMR). In the first section of this article, a brief and very simplified review of the NMR basic principles using classical physics is provided. The second section is focused on the description of the hardware solutions and the architecture of the NMR spectrometers. The software developments (LabVIEW programs) of the data-acquisition and signal processing techniques are presented in the third section. At the end, results of measurements are provided.

Carbonyl compounds generated from electronic cigarettes.

PubMed

Bekki, Kanae; Uchiyama, Shigehisa; Ohta, Kazushi; Inaba, Yohei; Nakagome, Hideki; Kunugita, Naoki

2014-10-28

Electronic cigarettes (e-cigarettes) are advertised as being safer than tobacco cigarettes products as the chemical compounds inhaled from e-cigarettes are believed to be fewer and less toxic than those from tobacco cigarettes. Therefore, continuous careful monitoring and risk management of e-cigarettes should be implemented, with the aim of protecting and promoting public health worldwide. Moreover, basic scientific data are required for the regulation of e-cigarette. To date, there have been reports of many hazardous chemical compounds generated from e-cigarettes, particularly carbonyl compounds such as formaldehyde, acetaldehyde, acrolein, and glyoxal, which are often found in e-cigarette aerosols. These carbonyl compounds are incidentally generated by the oxidation of e-liquid (liquid in e-cigarette; glycerol and glycols) when the liquid comes in contact with the heated nichrome wire. The compositions and concentrations of these compounds vary depending on the type of e-liquid and the battery voltage. In some cases, extremely high concentrations of these carbonyl compounds are generated, and may contribute to various health effects. Suppliers, risk management organizations, and users of e-cigarettes should be aware of this phenomenon.

MOFwich: Sandwiched Metal-Organic Framework-Containing Mixed Matrix Composites for Chemical Warfare Agent Removal.

PubMed

Peterson, Gregory W; Lu, Annie X; Hall, Morgan G; Browe, Matthew A; Tovar, Trenton; Epps, Thomas H

2018-02-28

This work describes a new strategy for fabricating mixed matrix composites containing layered metal-organic framework (MOF)/polymer films as functional barriers for chemical warfare agent protection. Through the use of mechanically robust polymers as the top and bottom encasing layers, a high-MOF-loading, high-performance-core layer can be sandwiched within. We term this multifunctional composite "MOFwich". We found that the use of elastomeric encasing layers enabled core layer reformation after breakage, an important feature for composites and membranes alike. The incorporation of MOFs into the core layer led to enhanced removal of chemical warfare agents while simultaneously promoting moisture vapor transport through the composite, showcasing the promise of these composites for protection applications.

Before Mina Shaughnessy: Basic Writing at Yale, 1920-1960

ERIC Educational Resources Information Center

Ritter, Kelly

2008-01-01

This article examines Yale's "Awkward Squad" of "basic" writers between 1920 and 1960. Using archival materials that illustrate the socioeconomic conditions of this early, "pre-Shaughnessy" site of remedial writing instruction, I argue for a re-definition of "basic" in composition studies using local, institutional values rather than generic…

Processing and properties of ceramic matrix-polymer composites for dental applications

NASA Astrophysics Data System (ADS)

Huang, Hsuan Yao

The basic composite structure of natural hard tissue was used to guide the design and processing of dental restorative materials. The design incorporates the methodology of using inorganic minerals as the main structural phase reinforced with a more ductile but tougher organic phase. Ceramic-polymer composites were prepared by slip casting a porous ceramic structure, heating and chemical treating the porous preform, infiltrating with monomer and then curing. The three factors that determined the mechanical properties of alumina-polymer composites were the type of polymer used, the method of silane treatments, and the type of bond between particles in the porous preforms. Without the use of silane coupling agents, the composites were measured to have a lower strength. The composite with a more "flexible" porous alumina network had a greater ability to plastically dissipate the energy of propagating cracks. However, the aggressive nature of the alumina particles on opposing enamel requires that these alumina-polymer composites have a wear compatible coating for practical application. A route to dense bioactive apatite wollastonite glass ceramics (AWGC)-polymer composites was developed. The problems associated with glass dissolution into the aqueous medium for slip casting were overcome with the use of silane. The role of heating rate and development of ceramic compact microstructure on composite properties was explored. In general, if isothermal heating was not applied, decreasing heating rate increased glass crystallinity and particle-particle fusion, but decreased pore volume. Also composite strength and fracture toughness decreased while modulus and hardness increased with decreasing heating rate. If isothermal heating was applied, glass crystallinity, pore content, and composite mechanical properties showed relatively little change regardless of the initial heating rate. The potential of AWGC-polymer composites for dental and implant applications was explored. Strengths and toughnesses were not severely degraded by immersion in simulated body fluids up to 30 days. The composite elastic modulus approached that of hard tissues and its wear behavior with opposing tooth was excellent. Growth of apatite over the entire composite surface was achieved in SBF. Growth of apatite in human whole saliva was achieved on the bioactive glass surface, but not on the composite surface.

Composites Based on Polytetrafluoroethylene and Detonation Nanodiamonds: Filler-Matrix Chemical Interaction and Its Effect on a Composite's Properties

NASA Astrophysics Data System (ADS)

Koshcheev, A. P.; Perov, A. A.; Gorokhov, P. V.; Zaripov, N. V.; Tereshenkov, A. V.; Khatipov, S. A.

2018-06-01

Specific properties of PTFE composites filled with ultradisperse detonation diamonds (UDDs) with different surface chemistries are studied. It is found for the first time that filler in the form of UDDs affects not only the rate of PTFE thermal decomposition in vacuum pyrolysis, but also the chemical composition of the products of degradation. The wear resistance of UDD/PTFE composites is shown to depend strongly on the UDD surface chemistry. The presence of UDDs in a PTFE composite is found to result in perfluorocarbon telomeres, released as a readily condensable fraction upon composite pyrolysis. The chemical interaction between PTFE and UDDs, characterized by an increase in the rate of gas evolution and a change in the desorbed gas's composition, is found to occur at temperature as low as 380°C. It is shown that the intensity of this interaction depends on the concentration of oxygen-containing surface groups, the efficiency of UDDs in terms of the composite's wear resistance being reduced due to the presence of these groups. Based on the experimental data, a conclusion is reached about the chemical interaction between UDDs and a PTFE matrix, its dependence on the nanodiamond surface chemistry, and its effect on a composite's tribology.

Electrochemically Active Polyaniline (PANi) Coated Carbon Nanopipes and PANi Nanofibers Containing Composite.

PubMed

Ramana, G Venkata; Kumar, P Sampath; Srikanth, Vadali V S S; Padya, Balaji; Jain, P K

2015-02-01

A composite constituted by carbon nanopipes (CNPs) and polyaniline nanofibers (PANi NFs) is synthesized using in-situ chemical oxidative polymerization. Owing to its electrochemical activity the composite is found to be suitable as a working electrode material in hybrid type supercapacitors. Microstructural and phase analyses of the composite showed that (i) CNP surfaces are coated with PANi and (ii) PANi coated CNPs are distributed among PANi NFs. The composite shows an excellent electrochemical activity and a high specific capacitance of ~224.39 F/g. The electro-chemical activity of the composite is explicated in correlation with crystallinity, intrinsic oxidation state, and doping degree of PANi in the composite. The electro-chemical activity of the composite is also explicated in correlation with BET surface area and ordered meso-porosity pertaining to the composite. Charge/discharge curves indicate that the specific capacitance of the composite is a result of electric double-layer capacitance offered by CNPs and Faradaic pseudo capacitance offered by PANi NFs.

Computing Equilibrium Chemical Compositions

NASA Technical Reports Server (NTRS)

Mcbride, Bonnie J.; Gordon, Sanford

1995-01-01

Chemical Equilibrium With Transport Properties, 1993 (CET93) computer program provides data on chemical-equilibrium compositions. Aids calculation of thermodynamic properties of chemical systems. Information essential in design and analysis of such equipment as compressors, turbines, nozzles, engines, shock tubes, heat exchangers, and chemical-processing equipment. CET93/PC is version of CET93 specifically designed to run within 640K memory limit of MS-DOS operating system. CET93/PC written in FORTRAN.

Using different assumptions of aerosol mixing state and chemical composition to predict CCN concentrations based on field measurements in urban Beijing

NASA Astrophysics Data System (ADS)

Ren, Jingye; Zhang, Fang; Wang, Yuying; Collins, Don; Fan, Xinxin; Jin, Xiaoai; Xu, Weiqi; Sun, Yele; Cribb, Maureen; Li, Zhanqing

2018-05-01

Understanding the impacts of aerosol chemical composition and mixing state on cloud condensation nuclei (CCN) activity in polluted areas is crucial for accurately predicting CCN number concentrations (NCCN). In this study, we predict NCCN under five assumed schemes of aerosol chemical composition and mixing state based on field measurements in Beijing during the winter of 2016. Our results show that the best closure is achieved with the assumption of size dependent chemical composition for which sulfate, nitrate, secondary organic aerosols, and aged black carbon are internally mixed with each other but externally mixed with primary organic aerosol and fresh black carbon (external-internal size-resolved, abbreviated as EI-SR scheme). The resulting ratios of predicted-to-measured NCCN (RCCN_p/m) were 0.90 - 0.98 under both clean and polluted conditions. Assumption of an internal mixture and bulk chemical composition (INT-BK scheme) shows good closure with RCCN_p/m of 1.0 -1.16 under clean conditions, implying that it is adequate for CCN prediction in continental clean regions. On polluted days, assuming the aerosol is internally mixed and has a chemical composition that is size dependent (INT-SR scheme) achieves better closure than the INT-BK scheme due to the heterogeneity and variation in particle composition at different sizes. The improved closure achieved using the EI-SR and INT-SR assumptions highlight the importance of measuring size-resolved chemical composition for CCN predictions in polluted regions. NCCN is significantly underestimated (with RCCN_p/m of 0.66 - 0.75) when using the schemes of external mixtures with bulk (EXT-BK scheme) or size-resolved composition (EXT-SR scheme), implying that primary particles experience rapid aging and physical mixing processes in urban Beijing. However, our results show that the aerosol mixing state plays a minor role in CCN prediction when the κorg exceeds 0.1.

Boundary-layer effects in composite laminates. I - Free-edge stress singularities. II - Free-edge stress solutions and basic characteristics

NASA Technical Reports Server (NTRS)

Wang, S. S.; Choi, I.

1982-01-01

The fundamental nature of the boundary-layer effect in fiber-reinforced composite laminates is formulated in terms of the theory of anisotropic elasticity. The basic structure of the boundary-layer field solution is obtained by using Lekhnitskii's stress potentials (1963). The boundary-layer stress field is found to be singular at composite laminate edges, and the exact order or strength of the boundary layer stress singularity is determined using an eigenfunction expansion method. A complete solution to the boundary-layer problem is then derived, and the convergence and accuracy of the solution are analyzed, comparing results with existing approximate numerical solutions. The solution method is demonstrated for a symmetric graphite-epoxy composite.

Architectural Design Propaedeutics in Russia: History and Prospects

NASA Astrophysics Data System (ADS)

Lee, I. S.

2017-11-01

Architectural design propaedeutics is the introductory course of the composition basics which largely determines the process of professional training of an architect and a designer and the result of their work in the form of artistically meaningful artificial human environment. The article gives a brief overview of the history of propedeutics development in Russia, the experience of application and the prospects of development of the methods used to teach the basics of composition to future professionals. The article considered the main direction of the VKHUTEMAS development, Moscow Architectural Institute. Further, the paper identifies he connection of propedeutics with the architectural and design practice of the corresponding period. The article addresses to the author’s personal experiences related to the composition basics learning at Moscow Architectural Institute in the 70-ies of the last century. Besides, it presents the examples of the works made by the students from South Ural State University at the Chair of Design and Fine Arts.

Modelling galaxy spectra in presence of interstellar dust - III. From nearby galaxies to the distant Universe

NASA Astrophysics Data System (ADS)

Cassarà, L. P.; Piovan, L.; Chiosi, C.

2015-07-01

Improving upon the standard evolutionary population synthesis technique, we present spectrophotometric models of galaxies with morphology going from spherical structures to discs, properly accounting for the effect of dust in the interstellar medium (ISM). The models contain three main physical components: the diffuse ISM made of gas and dust, the complexes of molecular clouds where active star formation occurs, and stars of any age and chemical composition. These models are based on robust evolutionary chemical description providing the total amount of gas and stars present at any age, and matching the properties of galaxies of different morphological types. We have considered the results obtained by Piovan et al. for the properties of the ISM, and those by Cassarà et al. for the spectral energy distribution (SED) of single stellar populations, both in presence of dust, to model the integral SEDs of galaxies of different morphological types, going from pure bulges to discs passing through a number of composite systems with different combinations of the two components. The first part of the paper is devoted to recall the technical details of the method and the basic relations driving the interaction between the physical components of the galaxy. Then, the main parameters are examined and their effects on the SED of three prototype galaxies are highlighted. The theoretical SEDs nicely match the observational ones both for nearby galaxies and those at high redshift.

Chemical composition of phosphorites of the Phosphoria Formation

USGS Publications Warehouse

Gulbrandsen, R.A.

1966-01-01

The chemical composition, both major and minor constituents, of 60 samples of phosphorite from the Phosphoria Formation was determined. Major constituents of the average phosphorite are, by weight per cent: SiO2, 11??9; Al2O3, 1??7; Fe2O3,1??1; MgO, 0??3; CaO, 44??0; Na2O, 0??6; K2O, 0??5; total H2O, 2??2; H2O-, 0??6; TiO2, 0??1; P2O5, 30??5; CO2, 2??2; SO3, 1??8; F, 3??1; organic matter, 2??1; and oil, 0??2. Uranium averages 0??009 per cent. The phosphate mineral is basically apatite, Ca5(PO4)3F, with small but significant and variable substitutions-Na, Sr, U and Th for Ca, and CO3 and SO4 for PO4. Rare metals not associated with apatite are associated principally with the organic-matter component of the rocks. This group includes As, Ag, Cd, Cr, Cu, Mo, Ni, Sb, Se, V and Zn. Chromium is the most abundant, having a modal abundance of 0??1 per cent and a maximum concentration of 0??3 per cent. The average phosphorite is composed of approximately 80 per cent apatite, 10 per cent quartz, 5 per cent muscovite-illite, 2 per cent organic matter, 1 per cent dolomite-calcite, 1 per cent iron oxide, and 1 per cent other components. It is texturally a medium-grained pellet phosphorite. ?? 1966.

Iron and aluminium oxides containing industrial wastes as adsorbents of heavy metals: Application possibilities and limitations.

PubMed

Jacukowicz-Sobala, Irena; Ociński, Daniel; Kociołek-Balawejder, Elżbieta

2015-07-01

Industrial wastes with a high iron or aluminium oxide content are produced in huge quantities as by-products of water treatment (water treatment residuals), bauxite processing (red mud) and hard and brown coal burning in power plants (fly ash). Although they vary in their composition, the wastes have one thing in common--a high content of amorphous iron and/or aluminium oxides with a large specific surface area, whereby this group of wastes shows very good adsorbability towards heavy metals, arsenates, selenates, etc. But their physical form makes their utilisation quite difficult, since it is not easy to separate the spent sorbent from the solution and high bed hydraulic resistances occur in dynamic regime processes. Nevertheless, because of the potential benefits of utilising the wastes in industrial effluent treatment, this issue attracts much attention today. This study describes in detail the waste generation processes, the chemical structure of the wastes, their physicochemical properties, and the mechanisms of fixing heavy metals and semimetals on the surface of iron and aluminium oxides. Typical compositions of wastes generated in selected industrial plants are given. A detailed survey of the literature on the adsorption applications of the wastes, including methods of their thermal and chemical activation, as well as regeneration of the spent sorbents, is presented. The existing and potential ways of modifying the physical form of the discussed group of wastes, making it possible to overcome the basic limitation on their practical use, are discussed. © The Author(s) 2015.

Differential effects of conifer and broadleaf litter inputs on soil organic carbon chemical composition through altered soil microbial community composition

PubMed Central

Wang, Hui; Liu, Shi-Rong; Wang, Jing-Xin; Shi, Zuo-Min; Xu, Jia; Hong, Pi-Zheng; Ming, An-Gang; Yu, Hao-Long; Chen, Lin; Lu, Li-Hua; Cai, Dao-Xiong

2016-01-01

A strategic selection of tree species will shift the type and quality of litter input, and subsequently magnitude and composition of the soil organic carbon (SOC) through soil microbial community. We conducted a manipulative experiment in randomized block design with leaf litter inputs of four native subtropical tree species in a Pinus massoniana plantation in southern China and found that the chemical composition of SOC did not differ significantly among treatments until after 28 months of the experiment. Contrasting leaf litter inputs had significant impacts on the amounts of total microbial, Gram-positive bacterial, and actinomycic PLFAs, but not on the amounts of total bacterial, Gram-negative bacterial, and fungal PLFAs. There were significant differences in alkyl/O-alkyl C in soils among the leaf litter input treatments, but no apparent differences in the proportions of chemical compositions (alkyl, O-alkyl, aromatic, and carbonyl C) in SOC. Soil alkyl/O-alkyl C was significantly related to the amounts of total microbial, and Gram-positive bacterial PLFAs, but not to the chemical compositions of leaf litter. Our findings suggest that changes in forest leaf litter inputs could result in changes in chemical stability of SOC through the altered microbial community composition. PMID:27256545

Differential effects of conifer and broadleaf litter inputs on soil organic carbon chemical composition through altered soil microbial community composition.

PubMed

Wang, Hui; Liu, Shi-Rong; Wang, Jing-Xin; Shi, Zuo-Min; Xu, Jia; Hong, Pi-Zheng; Ming, An-Gang; Yu, Hao-Long; Chen, Lin; Lu, Li-Hua; Cai, Dao-Xiong

2016-06-03

A strategic selection of tree species will shift the type and quality of litter input, and subsequently magnitude and composition of the soil organic carbon (SOC) through soil microbial community. We conducted a manipulative experiment in randomized block design with leaf litter inputs of four native subtropical tree species in a Pinus massoniana plantation in southern China and found that the chemical composition of SOC did not differ significantly among treatments until after 28 months of the experiment. Contrasting leaf litter inputs had significant impacts on the amounts of total microbial, Gram-positive bacterial, and actinomycic PLFAs, but not on the amounts of total bacterial, Gram-negative bacterial, and fungal PLFAs. There were significant differences in alkyl/O-alkyl C in soils among the leaf litter input treatments, but no apparent differences in the proportions of chemical compositions (alkyl, O-alkyl, aromatic, and carbonyl C) in SOC. Soil alkyl/O-alkyl C was significantly related to the amounts of total microbial, and Gram-positive bacterial PLFAs, but not to the chemical compositions of leaf litter. Our findings suggest that changes in forest leaf litter inputs could result in changes in chemical stability of SOC through the altered microbial community composition.

Differential effects of conifer and broadleaf litter inputs on soil organic carbon chemical composition through altered soil microbial community composition

NASA Astrophysics Data System (ADS)

Wang, Hui; Liu, Shi-Rong; Wang, Jing-Xin; Shi, Zuo-Min; Xu, Jia; Hong, Pi-Zheng; Ming, An-Gang; Yu, Hao-Long; Chen, Lin; Lu, Li-Hua; Cai, Dao-Xiong

2016-06-01

A strategic selection of tree species will shift the type and quality of litter input, and subsequently magnitude and composition of the soil organic carbon (SOC) through soil microbial community. We conducted a manipulative experiment in randomized block design with leaf litter inputs of four native subtropical tree species in a Pinus massoniana plantation in southern China and found that the chemical composition of SOC did not differ significantly among treatments until after 28 months of the experiment. Contrasting leaf litter inputs had significant impacts on the amounts of total microbial, Gram-positive bacterial, and actinomycic PLFAs, but not on the amounts of total bacterial, Gram-negative bacterial, and fungal PLFAs. There were significant differences in alkyl/O-alkyl C in soils among the leaf litter input treatments, but no apparent differences in the proportions of chemical compositions (alkyl, O-alkyl, aromatic, and carbonyl C) in SOC. Soil alkyl/O-alkyl C was significantly related to the amounts of total microbial, and Gram-positive bacterial PLFAs, but not to the chemical compositions of leaf litter. Our findings suggest that changes in forest leaf litter inputs could result in changes in chemical stability of SOC through the altered microbial community composition.

Chemical performance of multi-environment trials in lens (Lens culinaris M.).

PubMed

Karadavut, Ufuk; Palta, Cetin

2010-01-15

Genotype-environment (GE) interaction has been a major effect to determine stable lens (Lens culinaris (Medik.) Merr.) cultivars for chemical composition in Turkey. Utilization of the lines depends on their agronomic traits and stability of the chemical composition in diverse environments. The objectives of this study were: (i) to evaluate the influence of year and location on the chemical composition of lens genotypes; and (ii) to determine which cultivar is the most stable. Genotypes were evaluated over 3 years (2005, 2006 and 2007) at four locations in Turkey. Effects of year had the largest impact on all protein contents. GE interaction was analyzed by using linear regression techniques. Stability was estimated using the Eberhart and Russell method. 'Kişlik Kirmizi51' was the most stable cultivar for grain yield. The highest protein was obtained from 'Kişlik Kirmizi51' (4.6%) across environments. According to stability analysis, 'Firat 87' had the most stable chemical composition. This genotype had a regression coefficient (b(i) = 1) around unity, and deviations from regression values (delta(ij) = 0) around zero. Chemical composition was affected by year in this study. Temperature might have an effect on protein, oil, carbohydrate, fibre and ash. Firat 87 could be recommended for favourable environments. Copyright (c) 2009 Society of Chemical Industry.

Trilateral Design and Test Code for Military Bridging and Gap-Crossing Equipment

DTIC Science & Technology

2005-05-01

Property data should be provided for individual lamina and for the ( laminat - ed) composite . The required lamina properties are identified in...Resistance Welding ....... a Brazing ......................... X Machining ..................... a Chemical Composition : Element... Machining .................. b Chemical Composition : Element % Si .................................. 0.2 max Fe

The Bulk Elemental Composition of any Terrestrial Planets in the Alpha Centauri System

NASA Astrophysics Data System (ADS)

Lineweaver, C. H.; Schonberger, B. F. G.; Robles, J. A.

2010-04-01

Based on the devolatilization patterns in the solar system, and on the differences in the chemical compositions of the Sun and Alpha Centauri, we make estimates of the chemical composition of any Earth-like planets in the Alpha Centauri system.

Effect of chemical treatment of Kevlar fibers on mechanical interfacial properties of composites.

PubMed

Park, Soo-Jin; Seo, Min-Kang; Ma, Tae-Jun; Lee, Douk-Rae

2002-08-01

In this work, the effects of chemical treatment on Kevlar 29 fibers have been studied in a composite system. The surface characteristics of Kevlar 29 fibers were characterized by pH, acid-base value, X-ray photoelectron spectroscopy (XPS), and FT-IR. The mechanical interfacial properties of the final composites were studied by interlaminar shear strength (ILSS), critical stress intensity factor (K(IC)), and specific fracture energy (G(IC)). Also, impact properties of the composites were investigated in the context of differentiating between initiation and propagation energies and ductile index (DI) along with maximum force and total energy. As a result, it was found that chemical treatment with phosphoric acid solution significantly affected the degree of adhesion at interfaces between fibers and resin matrix, resulting in improved mechanical interfacial strength in the composites. This was probably due to the presence of chemical polar groups on Kevlar surfaces, leading to an increment of interfacial binding force between fibers and matrix in a composite system.

Effects of oxygen plasma treatment power on Aramid fiber III/BMI composite humidity resistance properties

NASA Astrophysics Data System (ADS)

Wang, Jing; Shi, Chen; Feng, Jiayue; Long, Xi; Meng, Lingzhi; Ren, Hang

2018-01-01

The effects of oxygen plasma treatment power on Aramid Fiber III chemical structure and its reinforced bismaleimides (BMI) composite humidity resistance properties were investigated in this work. The aramid fiber III chemical structure under different plasma treatment power were measured by FTIR. The composite bending strength and interlinear shear strength with different plasma treatment power before and after absorption water were tested respectively. The composite rupture morphology was observed by SEM. The FTIR results showed that oxygen plasma treatment do not change the fiber bulk chemical structure. The composite humidity resistance of bending strength and interlinear shear strength are similar for untreated and plasma treated samples. The retention rate of composite bending strength and interlinear shear strength are about 75% and 94%, respectively. The composite rupture mode turns to be the fiber failure after water absorption.

Subversive Complicity and Basic Writing across the Curriculum

ERIC Educational Resources Information Center

Villanueva, Victor

2013-01-01

What follows is a simple assertion: time for basic writing to get out from under, a call for us to inculcate a Basic Writing Across the Curriculum. It is time yet again to move away from the concept that basic writers are in need of remedies, in part because all composition courses are in some sense remedial, and to a greater degree because the…

Evaluating the effect of some mechanical properties for chemically treated various natural fibers reinforced polyester composite

NASA Astrophysics Data System (ADS)

Salih, Wafaa Mahdi; Abdulkader, Niveen Jamal; Salih, Sana Mahdi

2018-05-01

This research were studied the effect of some mechanical properties for composite materials reinforced fiber and prepared from material (polyester with various natural fibers) then studied the effect of chemical treatment on the same fiber immerse in 10% NaOH solution for half an hour and then compared, the results of the same test of composite materials without and with chemical treatment and the results proved that there is a clear effect when treat the fiber compared to non-chemical treatment of the fibers also noted that hemp fibers loaded the stress higher than other fibers for both cases to distinguish them that the hemp fiber has continuous fibers either the other fibers are characterized by the type of cross linking or chopped types in tensile test, and the results of the same test of composite materials without and with chemical treatment and the results proved that the hardness of the fiber composite while the treated fiber composite samples better than the untreated fiber, and from the figures the palm leaf has the highest value than lufa fiber, hemp fiber and the smallest value is in sisal fiber because of the nature of formation fibers materials.

Computing Properties Of Chemical Mixtures At Equilibrium

NASA Technical Reports Server (NTRS)

Mcbride, B. J.; Gordon, S.

1995-01-01

Scientists and engineers need data on chemical equilibrium compositions to calculate theoretical thermodynamic properties of chemical systems. Information essential in design and analysis of such equipment as compressors, turbines, nozzles, engines, shock tubes, heat exchangers, and chemical-processing equipment. CET93 is general program that calculates chemical equilibrium compositions and properties of mixtures for any chemical system for which thermodynamic data are available. Includes thermodynamic data for more than 1,300 gaseous and condensed species and thermal-transport data for 151 gases. Written in FORTRAN 77.

Ceramic composites reinforced with modified silicon carbide whiskers and method for modifying the whiskers

DOEpatents

Tiegs, Terry N.; Lindemer, Terrence B.

1991-01-01

Silicon carbide whisker-reinforced ceramic composites are fabricated in a highly reproducible manner by beneficating the surfaces of the silicon carbide whiskers prior to their usage in the ceramic composites. The silicon carbide whiskers which contain considerable concentrations of surface oxides and other impurities which interact with the ceramic composite material to form a chemical bond are significantly reduced so that only a relatively weak chemical bond is formed between the whisker and the ceramic material. Thus, when the whiskers interact with a crack propagating into the composite the crack is diverted or deflected along the whisker-matrix interface due to the weak chemical bonding so as to deter the crack propagation through the composite. The depletion of the oxygen-containing compounds and other impurities on the whisker surfaces and near surface region is effected by heat treating the whiskers in a suitable oxygen sparaging atmosphere at elevated temperatures. Additionally, a sedimentation technique may be utilized to remove whiskers which suffer structural and physical anomalies which render them undesirable for use in the composite. Also, a layer of carbon may be provided on the surface of the whiskers to further inhibit chemical bonding of the whiskers to the ceramic composite material.

Ceramic composites reinforced with modified silicon carbide whiskers and method for modifying the whiskers

DOEpatents

Tiegs, T.N.; Lindemer, T.B.

1991-02-19

Silicon carbide whisker-reinforced ceramic composites are fabricated in a highly reproducible manner by beneficating the surfaces of the silicon carbide whiskers prior to their usage in the ceramic composites. The silicon carbide whiskers which contain considerable concentrations of surface oxides and other impurities which interact with the ceramic composite material to form a chemical bond are significantly reduced so that only a relatively weak chemical bond is formed between the whisker and the ceramic material. Thus, when the whiskers interact with a crack propagating into the composite the crack is diverted or deflected along the whisker-matrix interface due to the weak chemical bonding so as to deter the crack propagation through the composite. The depletion of the oxygen-containing compounds and other impurities on the whisker surfaces and near surface region is effected by heat treating the whiskers in a suitable oxygen sparging atmosphere at elevated temperatures. Additionally, a sedimentation technique may be utilized to remove whiskers which suffer structural and physical anomalies which render them undesirable for use in the composite. Also, a layer of carbon may be provided on the surface of the whiskers to further inhibit chemical bonding of the whiskers to the ceramic composite material.

Ceramic composites reinforced with modified silicon carbide whiskers

DOEpatents

Tiegs, Terry N.; Lindemer, Terrence B.

1990-01-01

Silicon carbide whisker-reinforced ceramic composites are fabricated in a highly reproducible manner by beneficating the surfaces of the silicon carbide whiskers prior to their usage in the ceramic composites. The silicon carbide whiskers which contain considerable concentrations of surface oxides and other impurities which interact with the ceramic composite material to form a chemical bond are significantly reduced so that only a relatively weak chemical bond is formed between the whisker and the ceramic material. Thus, when the whiskers interact with a crack propagating into the composite the crack is diverted or deflected along the whisker-matrix interface due to the weak chemical bonding so as to deter the crack propagation through the composite. The depletion of the oxygen-containing compounds and other impurities on the whisker surfaces and near surface region is effected by heat treating the whiskers in a suitable oxygen sparaging atmosphere at elevated temperatures. Additionally, a sedimentation technique may be utilized to remove whiskers which suffer structural and physical anomalies which render them undesirable for use in the composite. Also, a layer of carbon may be provided on the surface of the whiskers to further inhibit chemical bonding of the whiskers to the ceramic composite material.

Global two dimensional chemistry model and simulation of atmospheric chemical composition

NASA Astrophysics Data System (ADS)

Zhang, Renjian; Wang, Mingxing; Zeng, Qingcun

2000-03-01

A global two-dimensional zonally averaged chemistry model is developed to study the chemi-cal composition of atmosphere. The region of the model is from 90°S to 90°N and from the ground to the altitude of 20 km with a resolution of 5° x 1 km. The wind field is residual circulation calcu-lated from diabatic rate. 34 species and 104 chemical and photochemical reactions are considered in the model. The sources of CH4, CO and NOx, which are divided into seasonal sources and non-seasonal sources, are parameterized as a function of latitude and time. The chemical composi-tion of atmosphere was simulated with emission level of CH4, CO and NOx in 1990. The results are compared with observations and other model results, showing that the model is successful to simu-late the atmospheric chemical composition and distribution of CH4.

A Statistical Approach for Judging Stability of Whole Mixture Chemical Composition over Time for Highly Complex Disinfection By-Product Mixtures from EPA's Four Lab Study

EPA Science Inventory

Chemical characterization of complex mixtures and assessment of stability over time of the characterized chemicals is crucial both to characterize exposure and to use data from one mixture as a surrogate for other similar mixtures. The chemical composition of test mixtures can va...

G. N. Lewis and the Chemical Bond.

ERIC Educational Resources Information Center

Pauling, Linus

1984-01-01

Discusses the contributions of G. N. Lewis to chemistry, focusing on his formulation of the basic principle of the chemical bond--the idea that the chemical bond consists of a pair of electrons held jointly by two atoms. (JN)

Cactus stem (Opuntia ficus-indica Mill): anatomy, physiology and chemical composition with emphasis on its biofunctional properties.

PubMed

Ventura-Aguilar, Rosa Isela; Bosquez-Molina, Elsa; Bautista-Baños, Silvia; Rivera-Cabrera, Fernando

2017-12-01

Cactus stem (Opuntia ficus-indica Mill) is native to Mesoamerica and marketed in different forms such as fresh, frozen or pre-cooked. Worldwide, this vegetable is recognized for its pharmaceutical actions, including its antioxidant, diuretic, anticarcinogenic, anti-inflammatory, anti-diabetic, and anti-hypercholesterolemic properties, as well as their antiviral and antispermatogenic effects. However, not all of these properties have been associated with its chemical composition; therefore, this review aims to present and integrate information available on the physiology and anatomy of cactus stem and its chemical composition, focusing on some of the many factors that determine its biofunctionality. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

78 FR 5500 - Manufacturer of Controlled Substances; Notice of Registration; Chemic Laboratories, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-25

...; Notice of Registration; Chemic Laboratories, Inc. By Notice dated September 25, 2012, and published in the Federal Register on October 2, 2012, 77 FR 60144, Chemic Laboratories, Inc., 480 Neponset Street... Chemic Laboratories, Inc., to manufacture the listed basic class of controlled substance is consistent...

Thin films as a platform for understanding the conversion mechanism of FeF2 cathodes in lithium-ion microbatteries

NASA Astrophysics Data System (ADS)

Santos-Ortiz, Reinaldo

Conversion material electrodes such as FeF2 possess the potential to deliver transformative improvements in lithium ion battery performance because they permit a reversible change of more than one Li-ion per 3d metal cation. They outperform current state of the art intercalation cathodes such as LiCoO2, which have volumetric and gravimetric energy densities that are intrinsically limited by single electron transfer. Current studies focus on composite electrodes that are formed by mixing with carbon (FeF 2-C), wherein the carbon is expected to act as a binder to support the matrix and facilitate electronic conduction. These binders complicate the understanding of the electrode-electrolyte interface (SEI) passivation layer growth, of Li agglomeration, of ion and electron transport, and of the basic phase transformation processes under electrochemical cycling. This research uses thin-films as a model platform for obtaining basic understanding to the structural and chemical foundations of the phase conversion processes. Thin film cathodes are free of the binders used in nanocomposite structures and may potentially provide direct basic insight to the evolution of the SEI passivation layer, electron and ion transport, and the electrochemical behavior of true complex phases. The present work consisted of three main tasks (1) Development of optimized processes to deposit FeF2 and LiPON thin-films with the required phase purity and microstructure; (2) Understanding their electron and ion transport properties and; (3) Obtaining insight to the correlation between structure and capacity in thin-film microbatteries with FeF2 thin-film cathode and LiPON thin-film solid electrolyte. Optimized pulsed laser deposition (PLD) growth produced polycrystalline FeF2 films with excellent phase purity and P42/mnm crystallographic symmetry. A schematic band diagram was deduced using a combination of UPS, XPS and UV-Vis spectroscopies. Room temperature Hall measurements reveal that as-deposited FeF2 is n-type with an electron mobility of 0.33 cm 2/V.s and a resistivity was 0.255 O.cm. The LiPON films were deposited by reactive sputtering in nitrogen, and the results indicate that the ionic conductivity is dependent on the amount of nitrogen incorporated into the film during processing. The highest ionic conductivity obtained was 1.431.9E-6 Scm-1 and corresponded to a chemical composition of Li1.9PO3.3N.21.

Fractional ultrabasic-basic evolution of upper-mantle magmatism: Evidence from xenoliths in kimberlites, inclusions in diamonds and experiments

NASA Astrophysics Data System (ADS)

Litvin, Yuriy; Kuzyura, Anastasia

2017-04-01

Ultrabasic peridotites and pyroxenites together with basic eclogites are the upper-mantle in situ rocks among xenoliths in kimberlites. Occasionally their diamond-bearing varieties have revealed within the xenoliths. Therewith the compositions of rock-forming minerals demonstrate features characteristic for primary diamond-included minerals of peridotite and eclogite parageneses (the elevated contents of Cr-component in peridotitic garnets and Na-jadeitic component in eclogitic clinopyroxenes). High-pressure experimental study of melting equilibria on the multicomponent peridotie-pyroxenite system olivine Ol - orthopyroxene Opx - clinopyroxene Cpx - garnet Grt showed that Opx disappeared in the peritectic reaction Opx+L→Cpx (Litvin, 1991). As a result, the invariant peritectic equilibrium Ol+Opx+Cpx+Grt+L of the ultrabasic system was found to transform into the univariant cotectic assemblage Ol+Cpx+Grt+L. Further experimental investigation showed that olivine reacts with jadeitic component (Jd) with formation of garnet at higher 4.5 GPa (Gasparik, Litvin, 1997). Study of melting relations in the multicomponent system Ol - Cpx - Jd permits to discover the peritectic point Ol+Omph+Grt+L (where Omph - omphacitic clinopyroxene) at concentration 3-4 wt.% Jd-component in the system. The reactionary loss of Opx and Ol makes it possible to transform the 4-phase garnet lherzolite ultrabasic association into the bimineral eclogite assemblage. The regime of fractional Ol, Cpx and Grt crystallization must be accompanied by increasing content of jadeitic component in residual melts that causes the complete "garnetization of olivine". In the subsequent evolution, the melts would have to fractionate for basic SiO2-saturated compositions responsible for petrogenesis of eclogite varieties marked with accessory corundum Crn, kyanite Ky and coesite Coe. Both the peritectic mechanisms occur in regime of fractional crystallization. The sequence of the upper-mantle fractional ultrabasic-basic magmatic evolution and petrogenesis may be controlled by the following melting relations: from Ol, Opx, L field to cotectic curve Ol, Opx, Cpx, L, peritectic point Ol, Opx, Cpx, Grt, L (loss of Opx), cotectic curve Ol, (Cpx+Jd), Grt, L, peritectic point Ol, (Cpx→Omph), Grt, L (loss of Ol), divariant field Omph,Grt,L, cotectic curve Ky, Omph, Grt, L, eutectic point Ky,Coe,Omph, Grt,L, subsolidus assemblage Ky,Coe,Omph, Grt. The fractional ultrabasic-basic evolution of the upper-mantle silicate-carbonate-carbon melts-solutions, which are responsible for genesis of diamond-and-inclusions associations and diamond-bearing peridotites and eclogites, follows the similar physico-chemical mechanisms (Litvin et al., 2016). This is illustrated by fractional syngenesis diagram for diamonds and associated minerals which construction is based on evidence from high pressure experiments. References Gasparik T., Litvin Yu.A (1997). Stability of Na2Mg2Si2O7 and melting relations on the forsterite - jadeite join at pressures up to 22 GPa. Eur, J. Mineral. 9(2), 311-326. Litvin Yu.A. (1991). Physico-Chemical Study of Melting of Materials from the Deep Earth. Moscow: Nauka. 312 p. Litvin Yu.A., Spivak A.V., Kuzyura A.V. (2016). Fundamentals of the mantle-carbonatite concept of diamond genesis, Geochemistry Internat. 34(10), 839-857.

Conceptual versus Algorithmic Learning in High School Chemistry: The Case of Basic Quantum Chemical Concepts--Part 1. Statistical Analysis of a Quantitative Study

ERIC Educational Resources Information Center

Papaphotis, Georgios; Tsaparlis, Georgios

2008-01-01

Part 1 of the findings are presented of a quantitative study (n = 125) on basic quantum chemical concepts taught in the twelfth grade (age 17-18 years) in Greece. A paper-and-pencil test of fourteen questions was used. The study compared performance in five questions that tested recall of knowledge or application of algorithmic procedures (type-A…

Materials Discovery via CALYPSO Methodology

NASA Astrophysics Data System (ADS)

Ma, Yanming

2014-03-01

Materials design has been the subject of topical interests in materials and physical sciences for long. Atomistic structures of materials occupy a central and often critical role, when establishing a correspondence between materials performance and their basic compositions. Theoretical prediction of atomistic structures of materials with the only given information of chemical compositions becomes crucially important, but it is extremely difficult as it basically involves in classifying a huge number of energy minima on the lattice energy surface. To tackle the problems, we have developed an efficient CALYPSO (Crystal structural AnLYsis by Particle Swarm Optimization) approach for structure prediction from scratch based on particle swarm optimization algorithm by taking the advantage of swarm intelligence and the spirit of structures smart learning. The method has been coded into CALYPSO software (http://www.calypso.cn) which is free for academic use. Currently, CALYPSO method is able to predict structures of three-dimensional crystals, isolated clusters or molecules, surface reconstructions, and two-dimensional layers. The applications of CALYPSO into purposed materials design of layered materials, high-pressure superconductors, and superhard materials were successfully made. Our design of superhard materials introduced a useful scheme, where the hardness value has been employed as the fitness function. This strategy might also be applicable into design of materials with other desired functional properties (e.g., thermoelectric figure of merit, topological Z2 number, etc.). For such a structural design, a well-understood structure to property formulation is required, by which functional properties of materials can be easily acquired at given structures. An emergent application is seen on design of photocatalyst materials.

A Gibbs Energy Minimization Approach for Modeling of Chemical Reactions in a Basic Oxygen Furnace

NASA Astrophysics Data System (ADS)

Kruskopf, Ari; Visuri, Ville-Valtteri

2017-12-01

In modern steelmaking, the decarburization of hot metal is converted into steel primarily in converter processes, such as the basic oxygen furnace. The objective of this work was to develop a new mathematical model for top blown steel converter, which accounts for the complex reaction equilibria in the impact zone, also known as the hot spot, as well as the associated mass and heat transport. An in-house computer code of the model has been developed in Matlab. The main assumption of the model is that all reactions take place in a specified reaction zone. The mass transfer between the reaction volume, bulk slag, and metal determine the reaction rates for the species. The thermodynamic equilibrium is calculated using the partitioning of Gibbs energy (PGE) method. The activity model for the liquid metal is the unified interaction parameter model and for the liquid slag the modified quasichemical model (MQM). The MQM was validated by calculating iso-activity lines for the liquid slag components. The PGE method together with the MQM was validated by calculating liquidus lines for solid components. The results were compared with measurements from literature. The full chemical reaction model was validated by comparing the metal and slag compositions to measurements from industrial scale converter. The predictions were found to be in good agreement with the measured values. Furthermore, the accuracy of the model was found to compare favorably with the models proposed in the literature. The real-time capability of the proposed model was confirmed in test calculations.

Unravelling the mechanisms for plant survival on gypsum soils: an analysis of the chemical composition of gypsum plants from Turkey.

PubMed

Bolukbasi, A; Kurt, L; Palacio, S

2016-03-01

Depending on their specificity to gypsum, plants can be classified as gypsophiles (gypsum exclusive) and gypsovags (non-exclusive). The former may further be segregated into wide and narrow gypsophiles, depending on the breadth of their distribution area. Narrow gypsum endemics have a putative similar chemical composition to plants non-exclusive to gypsum (i.e. gypsovags), which may indicate their similar ecological strategy as stress-tolerant plant refugees on gypsum. However, this hypothesis awaits testing in different regions of the world. We compared the chemical composition of four narrow gypsum endemics, one widely distributed gypsophile and six gypsovags from Turkey. Further, we explored the plasticity in chemical composition of Turkish gypsovags growing on high- and low-gypsum content soils. Differences were explored with multivariate analyses (RDA) and mixed models (REML). Narrow gypsum endemics segregated from gypsovags in their chemical composition according to RDAs (mainly due to higher K and ash content in the former). Nevertheless, differences were small and disappeared when different nutrients were analysed individually. All the gypsovags studied accumulated more S and ash when growing on high-gypsum than on low-gypsum soils. Similar to narrow gypsum endemics from other regions of the world, most local gypsum endemics from Turkey show a similar chemical composition to gypsovags. This may indicate a shared ecological strategy as stress-tolerant plants not specifically adapted to gypsum. Nevertheless, the narrow gypsum endemic Gypsophila parva showed a chemical composition typical of gypsum specialists, indicating that various strategies are feasible within narrowly distributed gypsophiles. © 2015 German Botanical Society and The Royal Botanical Society of the Netherlands.

Relating the Chemical Composition of Dissolved Organic Matter Draining Permafrost Soils to its Photochemical Degradation in Arctic Surface Waters.

NASA Astrophysics Data System (ADS)

Ward, C.; Cory, R. M.

2015-12-01

Thawing permafrost soils are expected to shift the chemical composition of DOM exported to and degraded in arctic surface waters. While DOM photo-degradation is an important component of the freshwater C cycle in the Arctic, the molecular controls on DOM photo-degradation remain poorly understood, making it difficult to predict how shifting chemical composition may alter DOM photo-degradation in arctic surface waters. To address this knowledge gap, we quantified the susceptibility of DOM draining the shallow organic mat and the deeper permafrost layer to complete photo-oxidation to CO₂ and partial photo-oxidation to compounds that remain in the DOM pool, and investigated changes in DOM chemical composition following sunlight exposure. DOM leached from the organic mat contained higher molecular weight, more oxidized and unsaturated aromatic species compared to permafrost DOM. Despite significant differences in initial chemical composition, permafrost and organic mat DOM had similar susceptibilities to complete photo-oxidation to CO₂. Concurrent losses of carboxyl moieties and shifts in chemical composition during photo-degradation indicated that carboxyl-rich tannin-like compounds in both DOM sources were likely photo-decarboxylated to CO₂. Permafrost DOM had a higher susceptibility to partial photo-oxidation compared to organic mat DOM, potentially due to a lower abundance of phenolic compounds that act as "antioxidants" and slow the oxidation of DOM. These results demonstrated how chemical composition controls the photo-degradation of DOM in arctic surface waters, and that DOM photo-degradation will likely remain an important component of the freshwater C budget in the Arctic with increased export of permafrost DOM to surface waters.

Method for the elucidation of the elemental composition of low molecular mass chemicals using exact masses of product ions and neutral losses: application to environmental chemicals measured by liquid chromatography with hybrid quadrupole/time-of-flight mass spectrometry.

PubMed

Suzuki, Shigeru; Ishii, Tetsuko; Yasuhara, Akio; Sakai, Shinichi

2005-01-01

A method for elucidating the elemental compositions of low molecular weight chemicals, based primarily on mass measurements made using liquid chromatography (LC) with time-of-flight mass spectrometry (TOFMS) and quadrupole/time-of-flight mass spectrometry (LC/QTOFMS), was developed and tested for 113 chemicals of environmental interest with molecular masses up to approximately 400 Da. As the algorithm incorporating the method is not affected by differences in the instrument used, or by the ionization method and other ionization conditions, the method is useful not only for LC/TOFMS, but also for all kinds of mass spectra measured with higher accuracy and precision (uncertainties of a few mDa) employing all ionization methods and on-line separation techniques. The method involves calculating candidate compositions for intact ionized molecules (ionized forms of the sample molecule that have lost or gained no more than a proton, i.e., [M+H](+) or [M-H](-)) as well as for fragment ions and corresponding neutral losses, and eliminating those atomic compositions for the molecules that are inconsistent with the corresponding candidate compositions of fragment ions and neutral losses. Candidate compositions were calculated for the measured masses of the intact ionized molecules and of the fragment ions and corresponding neutral losses, using mass uncertainties of 2 and 5 mDa, respectively. Compositions proposed for the ionized molecule that did not correspond to the sum of the compositions of a candidate fragment ion and its corresponding neutral loss were discarded. One, 2-5, 6-10, 11-20, and >20 candidate compositions were found for 65%, 39%, 1%, 1%, and 0%, respectively, for the 124 ionized molecules formed from the 113 chemicals tested (both positive and negative ions were obtained from 11 of the chemicals). However, no candidate composition was found for 2% of the test cases (i.e., 3 chemicals), for each of which the measured mass of one of the product ions was in error by 5-6.7 mDa.

Absolute parameters and chemical composition of the binary star OU Gem

NASA Astrophysics Data System (ADS)

Glazunova, L. V.; Mishenina, T. V.; Soubiran, C.; Kovtyukh, V. V.

2014-10-01

The absolute parameters and chemical composition of the BY Dra-type spectroscopic binary OU Gem (HD 45088) were determined on the basis of 10 high-resolution spectra. A new orbital solution of the binary system was determined, the binary ephemerides were specified, and the main physical and atmospheric parameters of the binary components were obtained. The chemical composition of both components was estimated for the first time for the stars of such type.

Pulsed plasma chemical synthesis of carbon-containing titanium and silicon oxide based nanocomposite

NASA Astrophysics Data System (ADS)

Kholodnaya, Galina; Sazonov, Roman; Ponomarev, Denis; Zhirkov, Igor

2018-03-01

The paper presents the results of the experimental investigation of the physical and chemical properties of the TixSiyCzOw composite nanopowders, which were first obtained using a pulsed plasma chemical method. The pulsed plasma chemical synthesis was achieved using a technological electron accelerator (TEA-500). The parameters of the electron beam are as follows: 400-450 keV electron energy, 60 ns half-amplitude pulse duration, up to 200 J pulse energy, and 5 cm beam diameter. The main physical and chemical properties of the obtained composites were studied (morphology, chemical, elemental and phase composition). The morphology of the TixSiyCzOw composites is multiform. There are large round particles, with an average size of above 150 nm. Besides, there are small particles (an average size is in the range of 15-40 nm). The morphology of small particles is in the form of crystallites. In the TixSiyCzOw synthesised composite, the peak with a maximum of 946 cm-1 was registered. The presence of IR radiation in this region of the spectrum is typical for the deformation of atomic oscillations in the Si‒О‒Ti bond, which indicates the formation of the solid solution. The composites consist of two crystal phases - anatase and rutile. The prevailing phase of the crystal structure is rutile.

The basics of intravascular optical coherence tomography

PubMed Central

Jąkała, Jacek; Kałuża, Grzegorz L.; Partyka, Łukasz; Proniewska, Klaudia; Pociask, Elżbieta; Zasada, Wojciech; Wojakowski, Wojciech; Gąsior, Zbigniew; Dudek, Dariusz

2015-01-01

Optical coherence tomography (OCT) has opened new horizons for intravascular coronary imaging. It utilizes near-infrared light to provide a microscopic insight into the pathology of coronary arteries in vivo. Optical coherence tomography is also capable of identifying the chemical composition of atherosclerotic plaques and detecting traits of their vulnerability. At present it is the only tool to measure the thickness of the fibrous cap covering the lipid core of the atheroma, and thus it is an exceptional modality to detect plaques that are prone to rupture (thin fibrous cap atheromas). Moreover, it facilitates distinguishing between plaque rupture and plaque erosion as a cause of acute intracoronary thrombosis. Optical coherence tomography is applied to guide angioplasties of coronary lesions and to assess outcomes of percutaneous coronary interventions broadly. It identifies stent malapposition, dissections, and thrombosis with unprecedented precision. Furthermore, OCT helps to monitor vessel healing after stenting. It evaluates the coverage of stent struts by the neointima and detects in-stent neoatherosclerosis. With so much potential, new studies are warranted to determine OCT's clinical impact. The following review presents the technical background, basics of OCT image interpretation, and practical tips for adequate OCT imaging, and outlines its established and potential clinical application. PMID:26161097

Guanidine: A Highly Efficient Stabilizer in Atmospheric New-Particle Formation.

PubMed

Myllys, Nanna; Ponkkonen, Tuomo; Passananti, Monica; Elm, Jonas; Vehkamäki, Hanna; Olenius, Tinja

2018-05-24

The role of a strong organobase, guanidine, in sulfuric acid-driven new-particle formation is studied using state-of-the-art quantum chemical methods and molecular cluster formation simulations. Cluster formation mechanisms at the molecular level are resolved, and theoretical results on cluster stability are confirmed with mass spectrometer measurements. New-particle formation from guanidine and sulfuric acid molecules occurs without thermodynamic barriers under studied conditions, and clusters are growing close to a 1:1 composition of acid and base. Evaporation rates of the most stable clusters are extremely low, which can be explained by the proton transfers and symmetrical cluster structures. We compare the ability of guanidine and dimethylamine to enhance sulfuric acid-driven particle formation and show that more than 2000-fold concentration of dimethylamine is needed to yield as efficient particle formation as in the case of guanidine. At similar conditions, guanidine yields 8 orders of magnitude higher particle formation rates compared to dimethylamine. Highly basic compounds such as guanidine may explain experimentally observed particle formation events at low precursor vapor concentrations, whereas less basic and more abundant bases such as ammonia and amines are likely to explain measurements at high concentrations.

The Teaching of Composition.

ERIC Educational Resources Information Center

Crowley, Sharon, Ed.

1976-01-01

This issue of the "Arizona English Bulletin" includes articles concerned with philosophy, psychology, and procedure in the composition classroom at all levels of instruction. Among the topics considered are contending with critics of composition, the back-to-basics movement, the writing process, writing modules, remedial writing, personalized…

The simulation method of chemical composition of vermicular graphite iron on the basis of genetic algorithm

NASA Astrophysics Data System (ADS)

Yusupov, L. R.; Klochkova, K. V.; Simonova, L. A.

2017-09-01

The paper presents a methodology of modeling the chemical composition of the composite material via genetic algorithm for optimization of the manufacturing process of products. The paper presents algorithms of methods based on intelligent system of vermicular graphite iron design

Chemical composition of fat and oil products

USDA-ARS?s Scientific Manuscript database

Fats and oils are an important dietary component, and contribute to the nutritional and sensory quality of foods. This chapter focuses on the chemical composition of fats and oils, and how these compositions affect the functional properties of fats and oils in foods. The focus will remain on the mos...

Dynamics of shearing force and its correlations with chemical compositions and in vitro dry matter digestibility of stylo (Stylosanthes guianensis) stem.

PubMed

Zi, Xuejuan; Li, Mao; Zhou, Hanlin; Tang, Jun; Cai, Yimin

2017-12-01

The study explored the dynamics of shearing force and its correlation with chemical compositions and in vitro dry matter digestibility (IVDMD) of stylo. The shearing force, diameter, linear density, chemical composition, and IVDMD of different height stylo stem were investigated. Linear regression analysis was done to determine the relationships between the shearing force and cut height, diameter, chemical composition, or IVDMD. The results showed that shearing force of stylo stem increased with plant height increasing and the crude protein (CP) content and IVDMD decreased but fiber content increased over time, resulting in decreased forage value. In addition, tall stem had greater shearing force than short stem. Moreover, shearing force is positively correlated with stem diameter, linear density and fiber fraction, but negatively correlated with CP content and IVDMD. Overall, shearing force is an indicator more direct, easier and faster to measure than chemical composition and digestibility for evaluation of forage nutritive value related to animal performance. Therefore, it can be used to evaluate the nutritive value of stylo.

Constraints on continental crustal mass loss via chemical weathering using lithium and its isotopes

NASA Astrophysics Data System (ADS)

Rudnick, R. L.; Liu, X. M.

2012-04-01

The continental crust has an "intermediate" bulk composition that is distinct from primary melts of peridotitic mantle (basalt or picrite). This mismatch between the "building blocks" and the "edifice" that is the continental crust points to the operation of processes that preferentially remove mafic to ultramafic material from the continents. Such processes include lower crustal recycling (via density foundering or lower crustal subduction - e.g., relamination, Hacker et al., 2011, EPSL), generation of evolved melts via slab melting, and/or chemical weathering. Stable isotope systems point to the influence of chemical weathering on the bulk crust composition: the oxygen isotope composition of the bulk crust is distinctly heavier than that of primary, mantle-derived melts (Simon and Lecuyer, 2005, G-cubed) and the Li isotopic composition of the bulk crust is distinctly lighter than that of mantle-derive melts (Teng et al., 2004, GCA; 2008, Chem. Geol.). Both signatures mark the imprint of chemical weathering on the bulk crust composition. Here, we use a simple mass balance model for lithium inputs and outputs from the continental crust to quantify the mass lost due to chemical weathering. We find that a minimum of 15%, a maximum of 60%, and a best estimate of ~40% of the original juvenile rock mass may have been lost via chemical weathering. The accumulated percentage of mass loss due to chemical weathering leads to an average global chemical weathering rate (CWR) of ~ 1×10^10 to 2×10^10 t/yr since 3.5 Ga, which is about an order of magnitude higher than the minimum estimates based on modern rivers (Gaillardet et al., 1999, Chem. Geol.). While we cannot constrain the exact portion of crustal mass loss via chemical weathering, given the uncertainties of the calculation, we can demonstrate that the weathering flux is non-zero. Therefore, chemical weathering must play a role in the evolution of the composition and mass of the continental crust.

Chemical Data Reporting Fact Sheet: Basic Information

EPA Pesticide Factsheets

EPA collects information on the types and quantities of chemicals produced in the U.S under the Chemical Data Reporting (CDR) requirements. This fact sheet outlines key information about CDR, including what data are collected and how the data are used.

The XRD Amorphous Component in John Klein Drill Fines at Yellowknife Bay, Gale Crater, Mars

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Ming,, Douglas W.; Blake, David; Vaniman, David; Bish, David L; Chipera, Steve; Downs, Robert; Morrison, Shaunna; Gellert, Ralf; Campbell, Iain;

Harnessing of radio frequency discharge for production of biologically compatible coatings for ophthalmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdullin, I.Sh.; Bragin, V.E.; Bykanov, A.N.

Gas discharge plasma modification of polymer materials and metals is one of the known physical approaches for improving of materials biocompatibility in ophthalmology and surgery. The surface treatment in RF discharges can be effectively realized in the discharge afterglow and in the discharge region itself too. This modification method is more convenient and produces more uniform surfaces in comparison with other discharge types. The carried out experiments and published up to now results show that interaction of UV radiation, fluxes of ions, electrons and metastable particles with material`s surface changes chemical composition and surface structure. The exerting of these agentsmore » on the sample surface produces the following effects. There are processes of physical and plasma-chemical surface etching producing effective surface cleaning of different types of contaminations. It may be surface contaminations by hydrocarbons because of preliminary surface contacts with biological or physical bodies. It may be surface contaminations caused by characteristic properties of chemical technology too. There is a surface layer with thickness from some angstroms up to few hundreds of angstroms. The chemical content and structure of this layer is distinguished from the bulk polymer properties. The presence of such {open_quotes}technological{close_quotes} contaminations produces the layer of material substantially differing from the base polymer. The basic layer physical and chemical properties for example, gas permeation rate may substantially differ from the base polymer. Attempts to clean the surface from these contaminations by chemical methods (solutions) have not been successful and produced contaminations of more deep polymer layers. So the plasma cleaning is the most profitable method of polymer treatment for removing the surface contaminations. The improving of wettability occurs during this stage of treatment.« less

Chemical similarity and local community assembly in the species rich tropical genus Piper.

PubMed

Salazar, Diego; Jaramillo, M Alejandra; Marquis, Robert J

2016-11-01

Community ecologists have strived to find mechanisms that mediate the assembly of natural communities. Recent evidence suggests that natural enemies could play an important role in the assembly of hyper-diverse tropical plant systems. Classic ecological theory predicts that in order for coexistence to occur, species differences must be maximized across biologically important niche dimensions. For plant-herbivore interactions, it has been recently suggested that, within a particular community, plant species that maximize the difference in chemical defense profiles compared to neighboring taxa will have a relative competitive advantage. Here we tested the hypothesis that plant chemical diversity can affect local community composition in the hyper-diverse genus Piper at a lowland wet forest location in Costa Rica. We first characterized the chemical composition of 27 of the most locally abundant species of Piper. We then tested whether species with different chemical compositions were more likely to coexist. Finally, we assessed the degree to which Piper phylogenetic relationships are related to differences in secondary chemical composition and community assembly. We found that, on average, co-occurring species were more likely to differ in chemical composition than expected by chance. Contrary to expectations, there was no phylogenetic signal for overall secondary chemical composition. In addition we found that species in local communities were, on average, more phylogenetically closely related than expected by chance, suggesting that functional traits other than those measured here also influence local assembly. We propose that selection by herbivores for divergent chemistries between closely related species facilitates the coexistence of a high diversity of congeneric taxa via apparent competition. © 2016 by the Ecological Society of America.

Composite material having high thermal conductivity and process for fabricating same

DOEpatents

Colella, N.J.; Davidson, H.L.; Kerns, J.A.; Makowiecki, D.M.

1998-07-21

A process is disclosed for fabricating a composite material such as that having high thermal conductivity and having specific application as a heat sink or heat spreader for high density integrated circuits. The composite material produced by this process has a thermal conductivity between that of diamond and copper, and basically consists of coated diamond particles dispersed in a high conductivity metal, such as copper. The composite material can be fabricated in small or relatively large sizes using inexpensive materials. The process basically consists, for example, of sputter coating diamond powder with several elements, including a carbide forming element and a brazeable material, compacting them into a porous body, and infiltrating the porous body with a suitable braze material, such as copper-silver alloy, thereby producing a dense diamond-copper composite material with a thermal conductivity comparable to synthetic diamond films at a fraction of the cost. 7 figs.

Properties of lightweight cement-based composites containing waste polypropylene

NASA Astrophysics Data System (ADS)

Záleská, Martina; Pavlíková, Milena; Pavlík, Zbyšek

2016-07-01

Improvement of buildings thermal stability represents an increasingly important trend of the construction industry. This work aims to study the possible use of two types of waste polypropylene (PP) for the development of lightweight cement-based composites with enhanced thermal insulation function. Crushed PP waste originating from the PP tubes production is used for the partial replacement of silica sand by 10, 20, 30, 40 and 50 mass%, whereas a reference mixture without plastic waste is studied as well. First, basic physical and thermal properties of granular PP random copolymer (PPR) and glass fiber reinforced PP (PPGF) aggregate are studied. For the developed composite mixtures, basic physical, mechanical, heat transport and storage properties are accessed. The obtained results show that the composites with incorporated PP aggregate exhibit an improved thermal insulation properties and acceptable mechanical resistivity. This new composite materials with enhanced thermal insulation function are found to be promising materials for buildings subsoil or floor structures.

Process for fabricating composite material having high thermal conductivity

DOEpatents

Colella, Nicholas J.; Davidson, Howard L.; Kerns, John A.; Makowiecki, Daniel M.

2001-01-01

A process for fabricating a composite material such as that having high thermal conductivity and having specific application as a heat sink or heat spreader for high density integrated circuits. The composite material produced by this process has a thermal conductivity between that of diamond and copper, and basically consists of coated diamond particles dispersed in a high conductivity metal, such as copper. The composite material can be fabricated in small or relatively large sizes using inexpensive materials. The process basically consists, for example, of sputter coating diamond powder with several elements, including a carbide forming element and a brazeable material, compacting them into a porous body, and infiltrating the porous body with a suitable braze material, such as copper-silver alloy, thereby producing a dense diamond-copper composite material with a thermal conductivity comparable to synthetic diamond films at a fraction of the cost.

Composite material having high thermal conductivity and process for fabricating same

DOEpatents

Colella, Nicholas J.; Davidson, Howard L.; Kerns, John A.; Makowiecki, Daniel M.

1998-01-01

A process for fabricating a composite material such as that having high thermal conductivity and having specific application as a heat sink or heat spreader for high density integrated circuits. The composite material produced by this process has a thermal conductivity between that of diamond and copper, and basically consists of coated diamond particles dispersed in a high conductivity metal, such as copper. The composite material can be fabricated in small or relatively large sizes using inexpensive materials. The process basically consists, for example, of sputter coating diamond powder with several elements, including a carbide forming element and a brazeable material, compacting them into a porous body, and infiltrating the porous body with a suitable braze material, such as copper-silver alloy, thereby producing a dense diamond-copper composite material with a thermal conductivity comparable to synthetic diamond films at a fraction of the cost.

The use of poly(vinyl phosphonic acid) microgels for the preparation of inherently magnetic Co metal catalyst particles in hydrogen production

NASA Astrophysics Data System (ADS)

Sahiner, Nurettin; Sagbas, Selin

2014-01-01

Novel poly(vinyl phosphonic acid) (p(VPA)) micro particle and composite p(VPA)-silica micro particle hydrogels are synthesized using a micro-emulsion polymerization technique. Porous p(VPA) particles are generated after removal of silica particles upon treatment of composite p(VPA) with 0.5 M NaOH solution. Bare, composite with silica, and porous p(VPA) micro particle hydrogels are used as templates and as reactors. Metal nanoparticles, Co, Ni, and Cu are generated in situ inside these hydrogels by chemical reduction of the absorbed metal ions with a reducing agent such as sodium boron hydride (NaBH4), and are used as catalyst in hydrogen production by hydrolysis of NaBH4 in a basic medium and ammonia borane (AB). The effects of reloaded metal ions, the reaction temperature, the porosity, the reusability, and the type of metal (Co, Ni, Cu) are investigated. The activation energy for hydrolysis of NaBH4, and AB by p(VPA)-Co is 28.02 and 25.51 kJ mol-1, respectively. The mass susceptibility measurements of composite p(VPA)-Co microgel is found as ferromagnetic. It is found that p(VPA) microgels provided better catalytic performance in comparison to macro p(VPA) hydrogels due to improved properties such as higher surface area, pore structure, and inherently magnetic behavior after multiple loadings-reduction of Co(II) from aqueous medium.

The provenance and chemical variation of sandstones associated with the Mid-continent Rift System, U.S.A.

USGS Publications Warehouse

Cullers, R.L.; Berendsen, P.

1998-01-01

Sandstones along the northern portion of the Precambrian Mid-continent Rift System (MRS) have been petrographically and chemically analyzed for major elements and a variety of trace elements, including the REE. After the initial extrusion of the abundant basalts along the MRS, dominantly volcaniclastic sandstones of the Oronto Group were deposited. These volcaniclastic sandstones are covered by quartzose and subarkosic sandstones of the Bayfield Group. Thus the sandstones of the Oronto Group were derived from previously extruded basalts, whereas, the sandstones of the Bayfield Group were derived from Precambrian granitic gneisses located on the rift flanks. The chemical variation of these sandstones closely reflects the changing detrital modes with time. The elemental composition of the sandstones confirms the source lithologies suggested by the mineralogy and clasts. The Oronto Group sandstones contain lower ratios of elements concentrated in silicic source rocks (La or Th) relative to elements concentrated in basic source rocks (Co, Cr, or Sc) than the Bayfield Group. Also, the average size of the negative Eu anomaly of the sandstones of the Oronto Group is significantly less (Eu/Eu* mean ?? standard deviation = 0.79 ?? 0.13) than that of the Bayfield Group (mean + standard deviation = 0.57 ?? 0.09), also suggesting a more basic source for the former than the latter. Mixing models of elemental ratios give added insight as to the evolution of the rift. These models suggest that the volcanistic sandstones of the lower portion of the Oronto Group are derived from about 80 to 90 percent basalt and 10 to 20 percent granitoids. The rest of the Oronto Group and the lower to middle portion of the Bayfield Group could have formed by mixing of about 30 to 60 percent basalt and 40 to 70 percent granitoids. The upper portion of the Bayfield Group is likely derived from 80 to 100 percent granitoids and zero to 20 percent basalt.

Xenobiology: State-of-the-Art, Ethics, and Philosophy of New-to-Nature Organisms.

PubMed

Schmidt, Markus; Pei, Lei; Budisa, Nediljko

The basic chemical constitution of all living organisms in the context of carbon-based chemistry consists of a limited number of small molecules and polymers. Until the twenty-first century, biology was mainly an analytical science and has now reached a point where it merges with engineering science, paving the way for synthetic biology. One of the objectives of synthetic biology is to try to change the chemical compositions of living cells, that is, to create an artificial biological diversity, which in turn fosters a new sub-field of synthetic biology, xenobiology. In particular, the genetic code in living systems is based on highly standardized chemistry composed of the same "letters" or nucleotides as informational polymers (DNA, RNA) and the 20 amino acids which serve as basic building blocks for proteins. The universality of the genetic code enables not only vertical gene transfer within the same species but also horizontal gene transfer across biological taxa, which require a high degree of standardization and interconnectivity. Although some minor alterations of the standard genetic code are found in nature (e.g., proteins containing non-conical amino acids exist in nature, and some organisms use alternated coding systems), all structurally deep chemistry changes within living systems are generally lethal, making the creation of artificial biological system an extremely difficult challenge.In this context, one of the great challenges for bioscience is the development of a strategy for expanding the standard basic chemical repertoire of living cells. Attempts to alter the meaning of the genetic information stored in DNA as an informational polymer by changing the chemistry of the polymer (i.e., xeno-nucleic acids) or by changes in the genetic code have already yielded successful results. In the future this should enable the partial or full redirection of the biological information flow to generate "new" version(s) of the genetic code derived from the "old" biological world.In addition to the scientific challenges, the attempt to increase biochemical diversity also raises important ethical and philosophical issues. Although promotors of this branch of synthetic biology highlight the many potential applications to come (e.g., novel tools for diagnostics and fighting infection diseases), such developments could also bring risks affecting social, political, and other structures of nearly all societies.

Study on Formation Mechanism of CaO-SiO2-Based Inclusions in Saw Wire Steel

NASA Astrophysics Data System (ADS)

Wang, Kun-Peng; Jiang, Min; Wang, Xin-Hua; Wang, Ying; Zhao, Hao-Qian; Cao, Zhan-Min

2017-12-01

Attempts were made to elucidate the formation mechanism of CaO-SiO2-based inclusions in saw wires by both laboratory experiments and industrial trials. The key point was to make clear the origin of CaO in such oxide inclusions. Probable origins of [Ca] in steel were first discussed, which can be taken into steel from the steel-slag reaction or ferrous alloy. As a result, slag-steel chemical reaction equilibrium was carefully evaluated at 1873 K (1600 °C) to classify the changes of dissolved aluminum ([Al]), total magnesium (Mg), and total calcium (Ca) in steel and the caused composition variations of inclusions. With the rise of slag basicity from 0.5 to 1.8, [Al] was remarkably increased from 0.00045 to 0.00139 mass pct, whereas Mg varied in the range of 0.00038 to 0.00048 mass pct. By contrast, Ca was constantly kept below 0.00003 mass pct. Accordingly, Al2O3 and MgO in inclusions witnessed obvious rises from 5 to 23 mass pct and from 2 to 8 mass pct, respectively. By contrast, inclusions were free of CaO when slag basicity was below 1.5. With slag basicity further increased to 1.8, CaO witnessed a negligible rise to only 1.0 mass pct on average. This phenomenon agreed well with thermodynamic calculations, which revealed that chemical reaction between steel and CaO in slag (for example, between [Si] and CaO) was weak to hardly supplying sufficient [Ca] to steel to increase CaO in inclusions. Ca contained in ferrous alloys as contaminations was not the cause of CaO-SiO2-based inclusions, either. The industrial trial results indicated that CaO-SiO2-based inclusions have been readily produced in short time just after BOF tapping. Also, a percentage of them changed slightly with the proceeding of refining. Based on the good agreement of laboratory, industrial, and thermodynamics calculations results, it can be reasonably concluded that CaO-SiO2-based inclusions in saw wire were exogenous particles from entrapped/emulsified top slag, but not products of slag-steel-inclusion chemical reactions.

The Effect of Chemical Functionalization on Mechanical Properties of Nanotube/Polymer Composites

NASA Technical Reports Server (NTRS)

Odegard, G. M.; Frankland, S. J. V.; Gates, T. S.

2003-01-01

The effects of the chemical functionalization of a carbon nanotube embedded in a nanotube/polyethylene composite on the bulk elastic properties are presented. Constitutive equations are established for both functionalized and non-functionalized nanotube composites systems by using an equivalent-continuum modeling technique. The elastic properties of both composites systems are predicted for various nanotube lengths, volume fractions, and orientations. The results indicate that for the specific composite material considered in this study, most of the elastic stiffness constants of the functionalized composite are either less than or equal to those of the non-functionalized composite.

77 FR 38085 - Manufacturer of Controlled Substances; Notice of Registration; Cayman Chemical Company

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-26

...; Notice of Registration; Cayman Chemical Company By Notice dated March 8, 2012, and published in the Federal Register on March 20, 2012, 77 FR 16263, Cayman Chemical Company, 1180 East Ellsworth Road, Ann... registration of Cayman Chemical Company to manufacture the listed basic classes of controlled substances is...

78 FR 69131 - Importer of Controlled Substances, Notice of Registration, Chattem Chemicals, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

... Registration, Chattem Chemicals, Inc. By Notice dated August 15, 2013, and published in the Federal Register on August 26, 2013, 78 FR 52801, Chattem Chemicals, Inc., 3801 St. Elmo Avenue, Chattanooga, Tennessee 37409... registration of Chattem Chemicals, Inc., to import the basic classes of controlled substances is consistent...

77 FR 24985 - Importer of Controlled Substances; Notice of Registration; ISP Freetown Fine Chemicals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

... Registration; ISP Freetown Fine Chemicals By Notice dated October 8, 2010, and published in the Federal Register on October 20, 2010, 75 FR 64743, ISP Freetown Fine Chemicals, 238 South Main Street, Assonet... that the registration of ISP Freetown Fine Chemicals to import the basic class of controlled substance...

77 FR 70188 - Manufacturer of Controlled Substances; Notice of Registration; Boehringer Ingelheim Chemicals, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-23

...; Notice of Registration; Boehringer Ingelheim Chemicals, Inc. By Notice dated July 17, 2012, and published in the Federal Register on July 26, 2012, 77 FR 43863, Boehringer Ingelheim Chemicals, Inc., 2820 N... Ingelheim Chemicals, Inc., to manufacture the listed basic classes of controlled substances is consistent...

78 FR 69134 - Manufacturer of Controlled Substances; Notice of Registration: AMPAC Fine Chemicals, LLC.

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-18

...; Notice of Registration: AMPAC Fine Chemicals, LLC. By Notice dated July 23, 2013, and published in the Federal Register on July 31, 2013, 78 FR 46372, AMPAC Fine Chemicals, LLC., Highway 50 and Hazel Avenue... AMPAC Fine Chemicals, LLC., to manufacture the listed basic classes of controlled substances is...

77 FR 64142 - Importer of Controlled Substances, Notice of Registration, ISP Freetown Fine Chemicals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-18

... Registration, ISP Freetown Fine Chemicals By Notice dated July 2, 2012, and published in the Federal Register on July 11, 2012, 77 FR 40910, ISP Freetown Fine Chemicals, 238 South Main Street, Assonet... that the registration of ISP Freetown Fine Chemicals to import the basic class of controlled substance...

77 FR 24988 - Manufacturer of Controlled Substances; Notice of Registration; ISP Freetown Fine Chemicals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-26

...; Notice of Registration; ISP Freetown Fine Chemicals By Notice dated October 8, 2010, and published in the Federal Register on October 20, 2010, 75 FR 64746, ISP Freetown Fine Chemicals, 238 South Main Street... Fine Chemicals, to manufacture the listed basic classes of controlled substances is consistent with the...

Conceptual versus Algorithmic Learning in High School Chemistry: The Case of Basic Quantum Chemical Concepts--Part 2. Students' Common Errors, Misconceptions and Difficulties in Understanding

ERIC Educational Resources Information Center

Papaphotis, Georgios; Tsaparlis, Georgios

2008-01-01

Part 2 of the findings are presented of a quantitative study (n = 125) on basic quantum chemical concepts taught at twelfth grade (age 17-18 years) in Greece. A paper-and-pencil test of fourteen questions was used that were of two kinds: five questions that tested recall of knowledge or application of algorithmic procedures (type-A questions);…

Rapid, Contactless and Non-Destructive Testing of Chemical Composition of Samples

NASA Astrophysics Data System (ADS)

Ivanov, O.; Vaseashta, A.; Stoychev, L.

Our results demonstrate that a new effect can be induced in each solid in a wide spectral range of electromagnetic irradiation. In the present manuscript we prove experimentally that one of the possible applications of this effect is for an express contactless control of the chemical composition of a series of samples, in this case, coins. The method has wide applicability ranging from defense and homeland security to several applications requiring rapid and nondestructive identification of chemical composition.

Composition for Critical Thinking: A Course Description.

ERIC Educational Resources Information Center

Lazere, Donald

Intended for college or secondary school teachers of courses beyond the basic level in freshman English and composition, this course description treats components of composition for critical thinking, including semantics, tone, logic, and argumentation, and their application to writing critical, argumentative, and research papers. The introduction…

Chemical aspects of the formation of the solar system

NASA Technical Reports Server (NTRS)

Arrhenius, G.

1978-01-01

Application of Alfven's theory for the formation of the solar system and the constraints imposed by the chemical composition of space materials are discussed with reference to chemical processes involved in the formation of the solar system. Evidence for the chemical properties of the space medium and the chemical consequences of the postulated physical differentiation processes are outlined, and interpretations based on structure and composition of meteorite material are indicated. A large range of topics, including processes involving chemical differentiation, temperature effects, and isotope fractionation, are examined.

The Acid-Base Properties and Chemical Composition of the Surface of the InSb-ZnTe System

NASA Astrophysics Data System (ADS)

Kirovskaya, I. A.; Shubenkova, E. G.; Timoshenko, O. T.; Filatova, T. N.

2008-04-01

The acid-base properties and chemical composition of the surface of solid solutions and binary components of the InSb-ZnTe system were studied by the hydrolytic adsorption, nonaqueous conductometric titration, mechanochemistry, IR spectroscopy, and mass spectrometry methods. The strength, nature, and concentration of acid centers were determined. Changes in the concentration of acid centers caused by surface exposure to CO and changes in the composition of the system were also studied. The mechanism of acid-base interactions was established. The chemical composition of the surface of system components exposed to air included adsorbed H2O molecules, OH- groups, hydrocarbon and oxocarbon compounds, and the products of surface atom oxidation. After thermal treatment in a vacuum, the composition of the surface approached the stoichiometric composition.

Studies on thermo-mechanical properties of chemically treated jute-polyester composite

NASA Astrophysics Data System (ADS)

Chaudhari, Vikas; Chandekar, Harichandra; Saboo, Jayesh; Mascarenhas, Adlete

2018-03-01

The effect of chemical treatments on jute-polyester composites is studied in this paper. The jute fabrics are chemically treated with NaOH and benzoyl chloride and its tensile and visco-elastic properties are compared with untreated jute composite. The NaOH treated jute-polyester composite show superior tensile strength and modulus compared to other jute-polyester composites. The glass transition temperature obtained from DMA shift to higher temperature for composites in comparison to polyester resin, this is due to restriction of mobility in chains due to introduction of jute reinforcement. The DMA results also show favourable results towards NaOH treatment i.e. higher storage modulus and lower tan δ values relative to untreated jute-polyester composite. The benzoyl treated jute-polyester composite however do not show promising results which may be attributed to the fact that the adhesion properties associated with similar ester functional groups in the benzoyl treated jute fabric and polyester resin were not obtained.

Modified silicon carbide whiskers

DOEpatents

Tiegs, Terry N.; Lindemer, Terrence B.

1991-01-01

Silicon carbide whisker-reinforced ceramic composites are fabricated in a highly reproducible manner by beneficating the surfaces of the silicon carbide whiskers prior to their usage in the ceramic composites. The silicon carbide whiskers which contain considerable concentrations of surface oxides and other impurities which interact with the ceramic composite material to form a chemical bond are significantly reduced so that only a relatively weak chemical bond is formed between the whisker and the ceramic material. Thus, when the whiskers interact with a crack propagating into the composite the crack is diverted or deflected along the whisker-matrix interface due to the weak chemical bonding so as to deter the crack propagation through the composite. The depletion of the oxygen-containing compounds and other impurities on the whisker surfaces and near surface region is effected by heat treating the whiskers in a suitable oxygen sparaging atmosphere at elevated temperatures. Additionally, a sedimentation technique may be utilized to remove whiskers which suffer structural and physical anomalies which render them undesirable for use in the composite. Also, a layer of carbon may be provided on the surface of the whiskers to further inhibit chemical bonding of the whiskers to the ceramic composite material.

Modified silicon carbide whiskers

DOEpatents

Tiegs, T.N.; Lindemer, T.B.

1991-05-21

Silicon carbide whisker-reinforced ceramic composites are fabricated in a highly reproducible manner by beneficating the surfaces of the silicon carbide whiskers prior to their usage in the ceramic composites. The silicon carbide whiskers which contain considerable concentrations of surface oxides and other impurities which interact with the ceramic composite material to form a chemical bond are significantly reduced so that only a relatively weak chemical bond is formed between the whisker and the ceramic material. Thus, when the whiskers interact with a crack propagating into the composite the crack is diverted or deflected along the whisker-matrix interface due to the weak chemical bonding so as to deter the crack propagation through the composite. The depletion of the oxygen-containing compounds and other impurities on the whisker surfaces and near surface region is effected by heat treating the whiskers in a suitable oxygen sparging atmosphere at elevated temperatures. Additionally, a sedimentation technique may be utilized to remove whiskers which suffer structural and physical anomalies which render them undesirable for use in the composite. Also, a layer of carbon may be provided on the surface of the whiskers to further inhibit chemical bonding of the whiskers to the ceramic composite material.

Composite Materials

NASA Technical Reports Server (NTRS)

1988-01-01

Langley Research Center researchers invented an advanced polymer, a chemical compound formed by uniting many small molecules to create a complex molecule with different chemical properties. The material is a thermoplastic polyimide that resists solvents. Other polymers of this generic type are soluble in solvents, thus cannot be used where solvents are present. High Technology Services (HTS), Inc. licensed technology and is engaged in development and manufacture of high performance plastics, resins and composite materials. Techimer Materials Division is using technology for composite matrix resins that offer heat resistance and protection from radiation, electrical and chemical degradation. Applications of new polymer include molding resins, adhesives and matrix resins for fiber reinforced composites.

Elemental Compositions of Comet 81P/Wild 2 Samples Collected by Stardust

NASA Technical Reports Server (NTRS)

Flynn, G. J.; Bleuet, P.; Borg, J.; Bradley, J.; Brenker, F.; Brennan, S.; Bridges, J.; Brownlee, D. E.; Bullock, E.; Clark, B. C.;

Improved Joining of Metal Components to Composite Structures

NASA Technical Reports Server (NTRS)

Semmes, Edmund

2009-01-01

Systems requirements for complex spacecraft drive design requirements that lead to structures, components, and/or enclosures of a multi-material and multifunctional design. The varying physical properties of aluminum, tungsten, Invar, or other high-grade aerospace metals when utilized in conjunction with lightweight composites multiply system level solutions. These multi-material designs are largely dependent upon effective joining techAn improved method of joining metal components to matrix/fiber composite material structures has been invented. The method is particularly applicable to equipping such thin-wall polymer-matrix composite (PMC) structures as tanks with flanges, ceramic matrix composite (CMC) liners for high heat engine nozzles, and other metallic-to-composite attachments. The method is oriented toward new architectures and distributing mechanical loads as widely as possible in the vicinities of attachment locations to prevent excessive concentrations of stresses that could give rise to delaminations, debonds, leaks, and other failures. The method in its most basic form can be summarized as follows: A metal component is to be joined to a designated attachment area on a composite-material structure. In preparation for joining, the metal component is fabricated to include multiple studs projecting from the aforementioned face. Also in preparation for joining, holes just wide enough to accept the studs are molded into, drilled, or otherwise formed in the corresponding locations in the designated attachment area of the uncured ("wet') composite structure. The metal component is brought together with the uncured composite structure so that the studs become firmly seated in the holes, thereby causing the composite material to become intertwined with the metal component in the joining area. Alternately, it is proposed to utilize other mechanical attachment schemes whereby the uncured composite and metallic parts are joined with "z-direction" fasteners. The resulting "wet" assembly is then subjected to the composite-curing heat treatment, becoming a unitary structure. It should be noted that this new art will require different techniques for CMC s versus PMC's, but the final architecture and companion curing philosophy is the same. For instance, a chemical vapor infiltration (CVI) fabrication technique may require special integration of the pre-form and

Porous multi-component material for the capture and separation of species of interest

DOEpatents

Addleman, Raymond S.; Chouyyok, Wilaiwan; Li, Xiaohong S.; Cinson, Anthony D.; Gerasimenko, Aleksandr A

2016-06-21

A method and porous multi-component material for the capture, separation or chemical reaction of a species of interest is disclosed. The porous multi-component material includes a substrate and a composite thin film. The composite thin film is formed by combining a porous polymer with a nanostructured material. The nanostructured material may include a surface chemistry for the capture of chemicals or particles. The composite thin film is coupled to the support or device surface. The method and material provides a simple, fast, and chemically and physically benign way to integrate nanostructured materials into devices while preserving their chemical activity.

Vegetable fibres from agricultural residues as thermo-mechanical reinforcement in recycled polypropylene-based green foams.

PubMed

Ardanuy, Mònica; Antunes, Marcelo; Velasco, José Ignacio

2012-02-01

Novel lightweight composite foams based on recycled polypropylene reinforced with cellulosic fibres obtained from agricultural residues were prepared and characterized. These composites, initially prepared by melt-mixing recycled polypropylene with variable fibre concentrations (10-25 wt.%), were foamed by high-pressure CO(2) dissolution, a clean process which avoids the use of chemical blowing agents. With the aim of studying the influence of the fibre characteristics on the resultant foams, two chemical treatments were applied to the barley straw in order to increase the α-cellulose content of the fibres. The chemical composition, morphology and thermal stability of the fibres and composites were analyzed. Results indicate that fibre chemical treatment and later foaming of the composites resulted in foams with characteristic closed-cell microcellular structures, their specific storage modulus significantly increasing due to the higher stiffness of the fibres. The addition of the fibres also resulted in an increase in the glass transition temperature of PP in both the solid composites and more significantly in the foams. Copyright © 2011 Elsevier Ltd. All rights reserved.

Experimental Constraints on the Chemical Differentiation of Mercurys Mantle

NASA Technical Reports Server (NTRS)

Boujibar, A.; Righter, K.; Pando, K.; Danielson, L.

2015-01-01

Mercury is known as being the most reduced terrestrial planet with the highest core/mantle ratio. Results from MESSENGER spacecraft have shown that its surface is FeO-poor (2-4 wt%) and S-rich (up to 6-7 wt%), which confirms the reducing nature of its silicate mantle. In addition several features suggest important melting stages of the Mercurian mantle: widespread volcanic deposits on its surface, a high crustal thickness (approximately 10% of the planet's volume) and chemical compositions of its surface suggesting several stages of differentiation and remelting processes. Therefore it is likely that igneous processes like magma ocean crystallization and continuous melting have induced chemical and mineralogical heterogeneities in the Mercurian mantle. The extent and nature of compositional variations produced by partial melting remains poorly constrained for the particular compositions of Mercury (very reducing conditions, low FeO-contents and high sulfur-contents). Melting experiments with bulk Mercury-analogue compositions are scarce and with poorly con-trolled starting compositions. Therefore additional experimental data are needed to better understand the differentiation processes that lead to the observed chemical compositions of Mercury's surface.

Chemical analysis of the moon at the surveyor v landing site.

PubMed

Turkevich, A L; Franzgrote, E J; Patterson, J H

1967-11-03

The chemical composition of the lunar surface material at a maria landing site has been determined by the alpha-scattering technique. Oxygen, silicon, and aluminum have been identified in the preliminary evaluation of the data. The general chemical composition is similar to that of a silicate of a basaltic type.

Chemical structure of wood charcoal by infrared spectroscopy and multivariate analysis

Treesearch

Nicole Labbe; David Harper; Timothy Rials; Thomas Elder

2006-01-01

In this work, the effect of temperature on charcoal structure and chemical composition is investigated for four tree species. Wood charcoal carbonized at various temperatures is analyzed by mid infrared spectroscopy coupled with multivariate analysis and by thermogravimetric analysis to characterize the chemical composition during the carbonization process. The...

Chemical Fingerprinting of Materials Developed Due to Environmental Issues

NASA Technical Reports Server (NTRS)

Smith, Doris A.; McCool, A. (Technical Monitor)

2000-01-01

Instrumental chemical analysis methods are developed and used to chemically fingerprint new and modified External Tank materials made necessary by changing environmental requirements. Chemical fingerprinting can detect and diagnose variations in material composition. To chemically characterize each material, fingerprint methods are selected from an extensive toolbox based on the material's chemistry and the ability of the specific methods to detect the material's critical ingredients. Fingerprint methods have been developed for a variety of materials including Thermal Protection System foams, adhesives, primers, and composites.

Hot corrosion of silicon carbide and silicon nitride at 1000 C

NASA Technical Reports Server (NTRS)

Fox, Dennis S.; Jacobson, Nathan S.; Smialek, James L.

1990-01-01

The sodium sulfate hot corrosion of silicon-based ceramics at 1000 C has been extensively studied. Deposition of the sodium sulfate corrodant from combustion products is discussed in relation to sodium air impurity and sulfur fuel impurity content. Corrosion occurs by the combined processes of oxidation to form protective silica scales and dissolution of these scales to form nonprotective sodium silicates. The chemical corrosion mechanisms are presented in terms of acidic/basic dissolution of oxides in molten salts. The reactions are strongly influenced by the presence of free carbon in the ceramic. Strength reductions have been measured and are attributed to pitting in SiC and grain boundary attack in Si3N4. Initial results of burner corrosion of two ceramic matrix composites are consistent with the models developed for monolithic ceramics.

Material interactions with the Low Earth Orbital (LEO) environment: Accurate reaction rate measurements

NASA Technical Reports Server (NTRS)

Visentine, James T.; Leger, Lubert J.

1987-01-01

To resolve uncertainties in estimated LEO atomic oxygen fluence and provide reaction product composition data for comparison to data obtained in ground-based simulation laboratories, a flight experiment has been proposed for the space shuttle which utilizes an ion-neutral mass spectrometer to obtain in-situ ambient density measurements and identify reaction products from modeled polymers exposed to the atomic oxygen environment. An overview of this experiment is presented and the methodology of calibrating the flight mass spectrometer in a neutral beam facility prior to its use on the space shuttle is established. The experiment, designated EOIM-3 (Evaluation of Oxygen Interactions with Materials, third series), will provide a reliable materials interaction data base for future spacecraft design and will furnish insight into the basic chemical mechanisms leading to atomic oxygen interactions with surfaces.

Thermal and chemical evolution in the early Solar System as recorded by FUN CAIs: Part II - Laboratory evaporation of potential CMS-1 precursor material

NASA Astrophysics Data System (ADS)

Mendybaev, Ruslan A.; Williams, Curtis D.; Spicuzza, Michael J.; Richter, Frank M.; Valley, John W.; Fedkin, Alexei V.; Wadhwa, Meenakshi

2017-03-01

We present the results of laboratory experiments in which a forsterite-rich melt estimated to be a potential precursor of Allende CMS-1 FUN CAI was evaporated into vacuum for different lengths of time at 1900 °C. The evaporation of this melt resulted in residues that define trajectories in chemical as well as magnesium, silicon and oxygen isotopic composition space and come very close to the measured properties of CMS-1. The isotopic composition of the evaporation residues was also used to determine the kinetic isotopic fractionation factors [α2,1 (vapor-melt) defined as the ratio of isotopes 2 and 1 of a given element in the evaporating gas divided by their ratio in the evaporating source] for evaporation of magnesium (α25,24 for 25Mg/24Mg), silicon (α29,28 for 29Si/28Si) and oxygen (α18,16 for 18O/16O) from the forsterite-rich melt at 1900 °C. The values of α25,24 = 0.98383 ± 0.00033 and α29,28 = 0.99010 ± 0.00038 are essentially independent of change in the melt composition as evaporation proceeds. In contrast, α18,16 changes from 0.9815 ± 0.0016 to ∼0.9911 when the residual melt composition changes from forsteritic to melilitic. Using the determined values of α25,24 and α29,28 and present-day bulk chemical composition of the CMS-1, the composition of the precursor of the inclusion was estimated to be close to the clinopyroxene + spinel + forsterite assemblage condensed from a solar composition gas. The correspondence between the chemical composition and isotopic fractionation of experimental evaporation residues and the present-day bulk chemical and isotopic compositions of CMS-1 is evidence that evaporation played a major role in the chemical evolution of CMS-1.

Characterization and prediction of chemical functions and weight fractions in consumer products.

PubMed

Isaacs, Kristin K; Goldsmith, Michael-Rock; Egeghy, Peter; Phillips, Katherine; Brooks, Raina; Hong, Tao; Wambaugh, John F

2016-01-01

Assessing exposures from the thousands of chemicals in commerce requires quantitative information on the chemical constituents of consumer products. Unfortunately, gaps in available composition data prevent assessment of exposure to chemicals in many products. Here we propose filling these gaps via consideration of chemical functional role. We obtained function information for thousands of chemicals from public sources and used a clustering algorithm to assign chemicals into 35 harmonized function categories (e.g., plasticizers, antimicrobials, solvents). We combined these functions with weight fraction data for 4115 personal care products (PCPs) to characterize the composition of 66 different product categories (e.g., shampoos). We analyzed the combined weight fraction/function dataset using machine learning techniques to develop quantitative structure property relationship (QSPR) classifier models for 22 functions and for weight fraction, based on chemical-specific descriptors (including chemical properties). We applied these classifier models to a library of 10196 data-poor chemicals. Our predictions of chemical function and composition will inform exposure-based screening of chemicals in PCPs for combination with hazard data in risk-based evaluation frameworks. As new information becomes available, this approach can be applied to other classes of products and the chemicals they contain in order to provide essential consumer product data for use in exposure-based chemical prioritization.

Relation of asphalt chemistry to physical properties and specifications.

DOT National Transportation Integrated Search

1984-01-01

This report constitutes a synthesis of published information concerning the chemical composition and characteristics of asphalt cements used in highway construction. The general relations between chemical composition and physical properties and speci...

Density Functionals of Chemical Bonding

PubMed Central

Putz, Mihai V.

2008-01-01

The behavior of electrons in general many-electronic systems throughout the density functionals of energy is reviewed. The basic physico-chemical concepts of density functional theory are employed to highlight the energy role in chemical structure while its extended influence in electronic localization function helps in chemical bonding understanding. In this context the energy functionals accompanied by electronic localization functions may provide a comprehensive description of the global-local levels electronic structures in general and of chemical bonds in special. Becke-Edgecombe and author’s Markovian electronic localization functions are discussed at atomic, molecular and solid state levels. Then, the analytical survey of the main workable kinetic, exchange, and correlation density functionals within local and gradient density approximations is undertaken. The hierarchy of various energy functionals is formulated by employing both the parabolic and statistical correlation degree of them with the electronegativity and chemical hardness indices by means of quantitative structure-property relationship (QSPR) analysis for basic atomic and molecular systems. PMID:19325846

Summaries of FY 1982 research in the chemical sciences

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1982-09-01

The purpose of this booklet is to help those interested in research supported by the Department of Energy's Division of Chemical Sciences, which is one of six Divisions of the Office of Basic Energy Sciences in the Office of Energy Research. These summaries are intended to provide a rapid means for becoming acquainted with the Chemical Sciences program to members of the scientific and technological public and interested persons in the Legislative and Executive Branches of the Government. Areas of research supported by the Division are to be seen in the section headings, the index and the summaries themselves. Energymore » technologies which may be advanced by use of the basic knowledge discovered in this program can be seen in the index and again (by reference) in the summaries. The table of contents lists the following: photochemical and radiation sciences; chemical physics; atomic physics; chemical energy; separation and analysis; chemical engineering sciences; offsite contracts; equipment funds; special facilities; topical index; institutional index for offsite contracts; investigator index.« less

Impacts of elevated atmospheric CO2 and O3 on forests: phytochemistry, trophic interactions, and ecosystem dynamics.

PubMed

Lindroth, Richard L

2010-01-01

Prominent among the many factors now affecting the sustainability of forest ecosystems are anthropogenically-generated carbon dioxide (CO2) and ozone (O3). CO2 is the substrate for photosynthesis and thus can accelerate tree growth, whereas O3 is a highly reactive oxygen species and interferes with basic physiological functions. This review summarizes the impacts of CO2 and O3 on tree chemical composition and highlights the consequences thereof for trophic interactions and ecosystem dynamics. CO2 and O3 influence phytochemical composition by altering substrate availability and biochemical/physiological processes such as photosynthesis and defense signaling pathways. Growth of trees under enriched CO2 generally leads to an increase in the C/N ratio, due to a decline in foliar nitrogen and concomitant increases in carbohydrates and phenolics. Terpenoid levels generally are not affected by atmospheric CO2 concentration. O3 triggers up-regulation of antioxidant defense pathways, leading to the production of simple phenolics and flavonoids (more so in angiosperms than gymnosperms). Tannins levels generally are unaffected, while terpenoids exhibit variable responses. In combination, CO2 and O3 exert both additive and interactive effects on tree chemical composition. CO2-and O3-mediated changes in plant chemistry influence host selection, individual performance (development, growth, reproduction), and population densities of herbivores (primarily phytophagous insects) and soil invertebrates. These changes can effect shifts in the amount and temporal pattern of forest canopy damage and organic substrate deposition. Decomposition rates of leaf litter produced under elevated CO2 and O3 may or may not be altered, and can respond to both the independent and interactive effects of the pollutants. Overall, however, CO2 and O3 effects on decomposition will be influenced more by their impacts on the quantity, rather than quality, of litter produced. A prominent theme to emerge from this and related reviews is that the effects of elevated CO2 and O3 on plant chemistry and ecological interactions are highly context- and species-specific, thus frustrating attempts to identify general, global patterns. Many of the interactions that govern above- and below-ground community and ecosystem processes are chemically mediated, ultimately influencing terrestrial carbon sequestration and feeding back to influence atmospheric composition. Thus, the discipline of chemical ecology is fundamentally important for elucidating the impacts of humans on the health and sustainability of forest ecosystems. Future research should seek to increase the diversity of natural products, species, and biomes studied; incorporate long-term, multi-factor experiments; and employ a comprehensive “genes to ecosystems” perspective that couples genetic/genomic tools with the approaches of evolutionary and ecosystem ecology.

Using a Thyroid Case Study and Error Plausibility to Introduce Basic Lab Skills

ERIC Educational Resources Information Center

Browning, Samantha; Urschler, Margaret; Meidl, Katherine; Peculis, Brenda; Milanick, Mark

2017-01-01

We describe a 3-hour session that provides students with the opportunity to review basic lab concepts and important techniques using real life scenarios. We began with two separate student-engaged discussions to remind/reinforce some basic concepts in physiology and review calculations with respect to chemical compounds. This was followed by…

USU Center of Excellence in Theory and Analysis of the Geo-Plasma Environment

DTIC Science & Technology

1992-05-25

AFM CN AOR9002 B. ADORE=S ICRYi. Stei md ZIP Codej 10. SOURCE OF FUNOING NOS. BuildPng 410 PROGRAM PROJECT TASK WORK UNIT.- Buling 410D..203 ELEMENT ...OTH radars, communications, and orbiting space structures. The overall goal of the research is to obtain a better understanding of the basic chemical...and orbiting space structures. The overall goal of the research is to obtain a better understanding of the basic chemical and physical processes

Composite Materials for Thermal Energy Storage: Enhancing Performance through Microstructures

PubMed Central

Ge, Zhiwei; Ye, Feng; Ding, Yulong

2014-01-01

Chemical incompatibility and low thermal conductivity issues of molten-salt-based thermal energy storage materials can be addressed by using microstructured composites. Using a eutectic mixture of lithium and sodium carbonates as molten salt, magnesium oxide as supporting material, and graphite as thermal conductivity enhancer, the microstructural development, chemical compatibility, thermal stability, thermal conductivity, and thermal energy storage performance of composite materials are investigated. The ceramic supporting material is essential for preventing salt leakage and hence provides a solution to the chemical incompatibility issue. The use of graphite gives a significant enhancement on the thermal conductivity of the composite. Analyses suggest that the experimentally observed microstructural development of the composite is associated with the wettability of the salt on the ceramic substrate and that on the thermal conduction enhancer. PMID:24591286

Refractories for high alkali environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rau, A.W.; Cloer, F.

1996-12-31

Information on refractories for high alkali environments is outlined. Information is presented on: product gallery; alkali attack; chemical reactions; basic layout of alkali cup test; criteria for rating alkali cup test samples; and basic layout of physical properties test.

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone

PubMed Central

Kikhtyanin, Oleg; Čapek, Libor; Tišler, Zdeněk; Velvarská, Romana; Panasewicz, Adriana; Diblíková, Petra; Kubička, David

2018-01-01

MgGa layered double hydroxides (Mg/Ga = 2–4) were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH3-TPD, CO2-TPD, SEM, and DRIFT) and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO2-TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO2-TPD curve was attributed to the decomposition of carbonates newly formed by CO2 interaction with interlayer carbonates rather than to CO2 desorption from basic sites. Accordingly, CO2-TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had practically no effect on the composition of reaction products suggesting that the basic sites in these catalysts acted similarly in aldol condensation of acetone with furfural. It was concluded that the properties of MgGa samples resembled in a great extent those of MgAl hydrotalcite-based materials and demonstrated their potential as catalysts for base-catalyzed reactions. PMID:29881721

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone.

PubMed

Kikhtyanin, Oleg; Čapek, Libor; Tišler, Zdeněk; Velvarská, Romana; Panasewicz, Adriana; Diblíková, Petra; Kubička, David

2018-01-01

MgGa layered double hydroxides (Mg/Ga = 2-4) were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH 3 -TPD, CO 2 -TPD, SEM, and DRIFT) and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO 2 -TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO 2 -TPD curve was attributed to the decomposition of carbonates newly formed by CO 2 interaction with interlayer carbonates rather than to CO 2 desorption from basic sites. Accordingly, CO 2 -TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had practically no effect on the composition of reaction products suggesting that the basic sites in these catalysts acted similarly in aldol condensation of acetone with furfural. It was concluded that the properties of MgGa samples resembled in a great extent those of MgAl hydrotalcite-based materials and demonstrated their potential as catalysts for base-catalyzed reactions.

Physico-chemical properties of MgGa mixed oxides and reconstructed layered double hydroxides and their performance in aldol condensation of furfural and acetone

NASA Astrophysics Data System (ADS)

Kikhtyanin, Oleg; Čapek, Libor; Tišler, Zdeněk; Velvarská, Romana; Panasewicz, Adriana; Diblíková, Petra; Kubička, David

2018-05-01

MgGa layered double hydroxides (Mg/Ga=2-4) were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH3-TPD, CO2-TPD, SEM and DRIFT) and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO2-TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T=450 °C on CO2-TPD curve was attributed to the decomposition of carbonates newly formed by CO2 interaction with interlayer carbonates rather than to CO2 desorption from basic sites. Accordingly, CO2-TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had practically no effect on the composition of reaction products suggesting that the basic sites in these catalysts acted similarly in aldol condensation of acetone with furfural. It was concluded that the properties of MgGa samples resembled in a great extent those of MgAl hydrotalcite-based materials and demonstrated their potential as catalysts for base-catalyzed reactions.

Chemical composition and strength of dolomite geopolymer composites

NASA Astrophysics Data System (ADS)

Aizat, E. A.; Al Bakri, A. M. M.; Liew, Y. M.; Heah, C. Y.

2017-09-01

The chemical composition of dolomite and the compressive strength of dolomite geopolymer composites were studied. The both composites prepared with mechanical mixer manufactured by with rotor speed of 350 rpm and curing in the oven for 24 hours at 80˚C. XRF analysis showThe dolomite raw materials contain fewer amounts of Si and Al but high Ca in its composition. Dolomite geopolymer composites with 20M of NaOH shows greater and optimum compressive strength compared to dolomite geopolymer with other NaOH molarity. This indicated better interaction of dolomite raw material and alkaline activator need high molarity of NaOH in order to increase the reactivity of dolomite.

Measurements of Positive Ambient Ions in Lamont OK as Part of the Holistic Interaction of Shallow Clouds Aerosols and Land Ecosystems (HISCALE II) Field Campaign

NASA Astrophysics Data System (ADS)

Abdelhamid, A.; Stark, H.; Worsnop, D. R.; Nowak, J. B.; Kuang, C.; Bullard, R.; Browne, E. C.

2017-12-01

Atmospheric ions control the electrical properties of the atmosphere, influence chemical composition via ion-molecule and/or ion-catalyzed reactions, and affect new particle formation. Understanding the role of ions in these processes requires knowledge of ionic chemical composition. Due to the low concentration of ions, chemical composition measurements have historically been challenging. Recent advances in mass spectrometry, such as the atmospheric pressure interface time-of-flight mass spectrometer (APi-TOF), are now making these measurements more feasible. Here, we present measurements of ambient cations during the HISCALE II field campaign (August- September 2016) in Lamont, OK. We discuss how the chemical composition of cations varies over the course of the campaign including before, during, and after new particle formation events. We specifically focus on the composition of organic nitrogen ions due to the potential importance of these compounds in atmospheric nucleation. We compare our results to measurements of neutral organic nitrogen compounds in order to gain insight into how organic nitrogen is chemically transformed in the atmosphere and how this influences new particle formation.

An Illuminating Reaction.

ERIC Educational Resources Information Center

Matthews, Catherine E.

1996-01-01

Describes the use of carbide lights as an excellent mechanism for introducing or reviewing many basic chemistry concepts including elements and compounds, endothermic and exothermic reactions, physical and chemical changes, and balancing chemical equations. (JRH)

Chemical Mixture Risk Assessment Additivity-Based Approaches

EPA Science Inventory

Powerpoint presentation includes additivity-based chemical mixture risk assessment methods. Basic concepts, theory and example calculations are included. Several slides discuss the use of "common adverse outcomes" in analyzing phthalate mixtures.

Characterization and Prediction of Chemical Functions and ...

EPA Pesticide Factsheets

Assessing exposures from the thousands of chemicals in commerce requires quantitative information on the chemical constituents of consumer products. Unfortunately, gaps in available composition data prevent assessment of exposure to chemicals in many products. Here we propose filling these gaps via consideration of chemical functional role. We obtained function information for thousands of chemicals from public sources and used a clustering algorithm to assign chemicals into 35 harmonized function categories (e.g., plasticizers, antimicrobials, solvents). We combined these functions with weight fraction data for 4115 personal care products (PCPs) to characterize the composition of 66 different product categories (e.g., shampoos). We analyzed the combined weight fraction/function dataset using machine learning techniques to develop quantitative structure property relationship (QSPR) classifier models for 22 functions and for weight fraction, based on chemical-specific descriptors (including chemical properties). We applied these classifier models to a library of 10196 data-poor chemicals. Our predictions of chemical function and composition will inform exposure-based screening of chemicals in PCPs for combination with hazard data in risk-based evaluation frameworks. As new information becomes available, this approach can be applied to other classes of products and the chemicals they contain in order to provide essential consumer product data for use in exposure-b

Process for derivatizing carbon nanotubes with diazonium species and compositions thereof

NASA Technical Reports Server (NTRS)

Bahr, Jeffrey L. (Inventor); Tour, James M. (Inventor); Yang, Jiping (Inventor)

2011-01-01

Methods for the chemical modification of carbon nanotubes involve the derivatization of multi- and single-wall carbon nanotubes, including small diameter (ca. 0.7 nm) single-wall carbon nanotubes, with diazonium species. The method allows the chemical attachment of a variety of organic compounds to the side and ends of carbon nanotubes. These chemically modified nanotubes have applications in polymer composite materials, molecular electronic applications, and sensor devices. The methods of derivatization include electrochemical induced reactions, thermally induced reactions, and photochemically induced reactions. Moreover, when modified with suitable chemical groups, the derivatized nanotubes are chemically compatible with a polymer matrix, allowing transfer of the properties of the nanotubes (such as, mechanical strength or electrical conductivity) to the properties of the composite material as a whole. Furthermore, when modified with suitable chemical groups, the groups can be polymerized to form a polymer that includes carbon nanotubes.

The Basic Aims of Discourse

ERIC Educational Resources Information Center

Kinneavy, James E.

1969-01-01

The author compares some systems of the aims of discourse ranging from the Aristotelian and Aquinas schools to the Buhler, Jakobsen, and Kinneavy theories, and pleads for the preservation of the liberal arts tradition with composition as a basic course. (DS)

English 540: Teaching Stretch and Studio Composition Practicum

ERIC Educational Resources Information Center

Davila, Bethany; Elder, Cristyn L.

2017-01-01

In the course overview, the authors state that this course prepares those who enroll to teach Stretch and Studio Composition at the University of New Mexico by introducing relevant theory and pedagogy in the areas of basic writing, multilingual writing, metacognition, and reading instruction. While the English 537: Teaching Composition Practicum…

Composition, Philosophy, and Rhetoric: The "Problem of Power."

ERIC Educational Resources Information Center

Sebberson, David

1993-01-01

Remarks on moments in Louise Wetherbee Phelps' book "Composition as a Human Science" where the absence of power presents a problematic for composition. Presents Jurgen Habermas for and against Phelps, noting the gestures of both authors against scientism while drawing on several of Habermas' basic concepts. Proposes rereading Aristotle's…

EAST VERSUS WEST IN THE US: CHEMICAL CHARACTERISTICS OF PM 2.5 DURING THE WINTER OF 1999

EPA Science Inventory

The chemical composition of PM2.5 was investigated at four sites (Rubidoux, CA, Phoenix, AZ, Philadelphia, PA, and RTP, NC) in January and February of 1999. Three samplers were used to determine both the overall mass and the chemical composition of the aerosol. Teflon filters wer...

Frequent Prescribed Burning as a Long-term Practice in Longleaf Pine Forests Does Not Affect Detrital Chemical Composition.

PubMed

Coates, T Adam; Chow, Alex T; Hagan, Donald L; Wang, G Geoff; Bridges, William C; Dozier, James H

2017-09-01

The O horizon, or detrital layer, of forest soils is linked to long-term forest productivity and health. Fuel reduction techniques, such as prescribed fire, can alter the thickness and composition of this essential ecosystem component. Developing an understanding of the changes in the chemical composition of forest detritus due to prescribed fire is essential for forest managers and stakeholders seeking sustainable, resilient, and productive ecosystems. In this study, we evaluated fuel quantity, fuel structure, and detrital chemical composition in longleaf pine ( Miller) forests that have been frequently burned for the last 40 yr at the Tom Yawkey Wildlife Center in Georgetown, SC. Our results suggest that frequent prescribed fire reduces forest fuel quantity ( < 0.01) and vertical structure ( = 0.01). Using pyrolysis-gas chromatography/mass spectrometry as a molecular technique to analyze detrital chemical composition, including aromatic compounds and polycyclic aromatic hydrocarbons, we found that the chemical composition of forest detritus was nearly uniform for both unburned and burned detritus. Our burning activities varied in the short term, consisting of annual dormant, annual growing, and biennial dormant season burns. Seasonal distinctions were present for fuel quantity and vertical fuel structure, but these differences were not noted for the benzene/phenol ratio. These results are significant as more managers consider burning existing longleaf stands while determining effective management practices for longleaf stands yet to be established. Managers of such stands can be confident that frequent, low-intensity, low-severity prescribed burns in longleaf pine forests do little to affect the long-term chemical composition of forest detritus. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Quantitative measurement of the chemical composition of geological standards with a miniature laser ablation/ionization mass spectrometer designed for in situ application in space research

NASA Astrophysics Data System (ADS)

Neuland, M. B.; Grimaudo, V.; Mezger, K.; Moreno-García, P.; Riedo, A.; Tulej, M.; Wurz, P.

2016-03-01

A key interest of planetary space missions is the quantitative determination of the chemical composition of the planetary surface material. The chemical composition of surface material (minerals, rocks, soils) yields fundamental information that can be used to answer key scientific questions about the formation and evolution of the planetary body in particular and the Solar System in general. We present a miniature time-of-flight type laser ablation/ionization mass spectrometer (LMS) and demonstrate its capability in measuring the elemental and mineralogical composition of planetary surface samples quantitatively by using a femtosecond laser for ablation/ionization. The small size and weight of the LMS make it a remarkable tool for in situ chemical composition measurements in space research, convenient for operation on a lander or rover exploring a planetary surface. In the laboratory, we measured the chemical composition of four geological standard reference samples USGS AGV-2 Andesite, USGS SCo-l Cody Shale, NIST 97b Flint Clay and USGS QLO-1 Quartz Latite with LMS. These standard samples are used to determine the sensitivity factors of the instrument. One important result is that all sensitivity factors are close to 1. Additionally, it is observed that the sensitivity factor of an element depends on its electron configuration, hence on the electron work function and the elemental group in agreement with existing theory. Furthermore, the conformity of the sensitivity factors is supported by mineralogical analyses of the USGS SCo-l and the NIST 97b samples. With the four different reference samples, the consistency of the calibration factors can be demonstrated, which constitutes the fundamental basis for a standard-less measurement-technique for in situ quantitative chemical composition measurements on planetary surface.

In vivo ultrasound and biometric measurements predict the empty body chemical composition in Nellore cattle.

PubMed

Castilhos, A M; Francisco, C L; Branco, R H; Bonilha, S F M; Mercadante, M E Z; Meirelles, P R L; Pariz, C M; Jorge, A M

2018-05-04

Evaluation of the body chemical composition of beef cattle can only be measured postmortem and those data cannot be used in real production scenarios to adjust nutritional plans. The objective of this study was to develop multiple linear regression equations from in vivo measurements, such as ultrasound parameters [backfat thickness (uBFT, mm), rump fat thickness (uRF, mm), and ribeye area (uLMA, cm2)], shrunk body weight (SBW, kg), age (AG, d), hip height (HH, m), as well as from postmortem measurements (composition of the 9th to 11th rib section) to predict the empty body and carcass chemical composition for Nellore cattle. Thirty-three young bulls were used (339 ± 36.15 kg and 448 ± 17.78 d for initial weight and age, respectively). Empty body chemical composition (protein, fat, water, and ash in kg) was obtained by combining noncarcass and carcass components. Data were analyzed using the PROC REG procedure of SAS software. Mallows' Cp values were close to the ideal value of number of independent variables in the prediction equations plus one. Equations to predict chemical components of both empty body and carcass using in vivo measurements presented higher R2 values than those determined by postmortem measurements. Chemical composition of the empty body using in vivo measurements was predicted with R2 > 0.73. Equations to predict chemical composition of the carcass from in vivo measurements showed R2 lower (R2< 0.68) than observed for empty body, except for the water (R2 = 0.84). The independent variables SBW, uRF, and AG were sufficient to predict the fat, water, energy components of the empty body, whereas for estimation of protein content the uRF, HH, and SBW were satisfactory. For the calculation of the ash, the SBW variable in the equation was sufficient. Chemical compounds from components of the empty body of Nellore cattle can be calculated by the following equations: protein (kg) = 47.92 + 0.18 × SBW - 1.46 × uRF - 30.72 × HH (R2 = 0.94, RMSPE = 1.79); fat (kg) = 11.33 + 0.16 × SBW + 2.09 × uRF - 0.06 × AG (R2 = 0.74, RMSPE = 4.18); water (kg) = - 34.00 + 0.55 × SBW + 0.10 × AG - 2.34 × uRF (R2 = 0.96, RMSPE = 5.47). In conclusion, the coefficients of determination (for determining the chemical composition of the empty body) of the equations derived from in vivo measures were higher than those of the equations obtained from rib section measurements taken postmortem, and better than coefficients of determination of the equations to predict the chemical composition of the carcass.

Temperature response of litter and soil organic matter decomposition is determined by chemical composition of organic material.

PubMed

Erhagen, Björn; Öquist, Mats; Sparrman, Tobias; Haei, Mahsa; Ilstedt, Ulrik; Hedenström, Mattias; Schleucher, Jürgen; Nilsson, Mats B

2013-12-01

The global soil carbon pool is approximately three times larger than the contemporary atmospheric pool, therefore even minor changes to its integrity may have major implications for atmospheric CO2 concentrations. While theory predicts that the chemical composition of organic matter should constitute a master control on the temperature response of its decomposition, this relationship has not yet been fully demonstrated. We used laboratory incubations of forest soil organic matter (SOM) and fresh litter material together with NMR spectroscopy to make this connection between organic chemical composition and temperature sensitivity of decomposition. Temperature response of decomposition in both fresh litter and SOM was directly related to the chemical composition of the constituent organic matter, explaining 90% and 70% of the variance in Q10 in litter and SOM, respectively. The Q10 of litter decreased with increasing proportions of aromatic and O-aromatic compounds, and increased with increased contents of alkyl- and O-alkyl carbons. In contrast, in SOM, decomposition was affected only by carbonyl compounds. To reveal why a certain group of organic chemical compounds affected the temperature sensitivity of organic matter decomposition in litter and SOM, a more detailed characterization of the (13) C aromatic region using Heteronuclear Single Quantum Coherence (HSQC) was conducted. The results revealed considerable differences in the aromatic region between litter and SOM. This suggests that the correlation between chemical composition of organic matter and the temperature response of decomposition differed between litter and SOM. The temperature response of soil decomposition processes can thus be described by the chemical composition of its constituent organic matter, this paves the way for improved ecosystem modeling of biosphere feedbacks under a changing climate. © 2013 John Wiley & Sons Ltd.

A rapid method for the computation of equilibrium chemical composition of air to 15000 K

NASA Technical Reports Server (NTRS)

Prabhu, Ramadas K.; Erickson, Wayne D.

1988-01-01

A rapid computational method has been developed to determine the chemical composition of equilibrium air to 15000 K. Eleven chemically reacting species, i.e., O2, N2, O, NO, N, NO+, e-, N+, O+, Ar, and Ar+ are included. The method involves combining algebraically seven nonlinear equilibrium equations and four linear elemental mass balance and charge neutrality equations. Computational speeds for determining the equilibrium chemical composition are significantly faster than the often used free energy minimization procedure. Data are also included from which the thermodynamic properties of air can be computed. A listing of the computer program together with a set of sample results are included.

Chemical composition and antifungal activity of the essential oils of Schinus weinmannifolius collected in the spring and winter.

PubMed

Hernandes, Camila; Taleb-Contini, Silvia H; Bartolomeu, Ana Carolina D; Bertoni, Bianca W; França, Suzelei C; Pereira, Ana Maria S

2014-09-01

Reports on the chemical and pharmacological profile of the essential oil of Schinus weinmannifolius do not exist, although other Schinus species have been widely investigated for their biological activities. This work aimed to evaluate the chemical composition and antimicrobial activity of the essential oil of S. weinmannifolius collected in the spring and winter. The essential oils were extracted by hydrodistillation, analyzed by GC/MS and submitted to microdilution tests, to determine the minimum inhibitory concentration. The oils displayed different chemical composition and antimicrobial action. Bicyclogermacrene and limonene predominated in the oils extracted in the winter and spring, respectively, whereas only the latter oil exhibited antifungal activity.

Science Advisory Committee on Chemicals Basic Information

EPA Pesticide Factsheets

The SACC will provide independent scientific advice and recommendations to the EPA on the scientific basis for risk assessments, methodologies, and pollution prevention measures and approaches for chemicals regulated under the TSCA.

Influence of ingredients and chemical components on the quality of Chinese steamed bread.

PubMed

Zhu, Fan

2014-11-15

Chinese steamed bread (CSB) is a staple food in China since ancient time. The basic ingredients include wheat flour, yeast/sourdough, and water. Current consumer trends urge the production of CSB on a large scale as well as the formulation of healthier CSB with specific nutritional benefits. This requires a better definition of the relationship between the properties of ingredients/chemical components and CSB quality. This review summarises the recent advances in understanding the roles of basic and optional ingredients and their chemical components in the appearance, textural, sensory, and shelf-life properties of CSB, and provides suggestions for further research to match the current trends. Copyright © 2014 Elsevier Ltd. All rights reserved.

Can long chain n-3 fatty acids from feed be converted into very long chain n-3 fatty acids in fillets from farmed rainbow trout (Oncorhynchus mykiss)?

NASA Astrophysics Data System (ADS)

Lušnic Polak, M.; Demšar, L.; Luzar, U.; Polak, T.

2017-09-01

The link between the basic chemical and fatty acid composition of trout feed on one hand and trout (Oncorhynchus mykiss) meat (fillet) was investigated.. The content of 52 fatty acids from feed and trout meat lipids was determined by in-situ transesterification and capillary column gas-liquid chromatography. On average, 100 g of trout feed contained 7.4 g of moisture, 47.7 g of proteins, 6.09 g of ash, 21.4 g of fat, and as for fatty acid composition, 47.8 wt. % were monounsaturated, 34.0 wt. % were polyunsaturated and 18.1 wt. % were saturated fatty acids, with the PS ratio 1.88, n-6/n-3 ratio 1.74, 0.80 wt. % of trans and 3.28 wt. % of very long chain n-3 fatty acids. On average, 100 g of trout meat contained 76.1 g of moisture, 21.4 g of proteins, 1.34 g of ash, 2.52 g of fat, and in the fatty acid composition 42.1 wt. % were monounsaturated, 38.2 wt. % were polyunsaturated and 18.9 wt. % were saturated fatty acids, with the PS ratio 2.02, n-6/n-3 ratio 0.98, 0.95 wt. % of trans and 13.25 wt. % of very long chain n-3 fatty acids.

Layer-by-Layer Assembled Architecture of Polyelectrolyte Multilayers and Graphene Sheets on Hollow Carbon Spheres/Sulfur Composite for High-Performance Lithium-Sulfur Batteries.

PubMed

Wu, Feng; Li, Jian; Su, Yuefeng; Wang, Jing; Yang, Wen; Li, Ning; Chen, Lai; Chen, Shi; Chen, Renjie; Bao, Liying

2016-09-14

In the present work, polyelectrolyte multilayers (PEMs) and graphene sheets are applied to sequentially coat on the surface of hollow carbon spheres/sulfur composite by a flexible layer-by-layer (LBL) self-assembly strategy. Owing to the strong electrostatic interactions between the opposite charged materials, the coating agents are very stable and the coating procedure is highly efficient. The LBL film shows prominent impact on the stability of the cathode by acting as not only a basic physical barrier, and more importantly, an ion-permselective film to block the polysulfides anions by Coulombic repulsion. Furthermore, the graphene sheets can help to stabilize the polyelectrolytes film and greatly reduce the inner resistance of the electrode by changing the transport of the electrons from a "point-to-point" mode to a more effective "plane-to-point'' mode. On the basis of the synergistic effect of the PEMs and graphene sheets, the fabricated composite electrode exhibits very stable cycling stability for over 200 cycles at 1 A g(-1), along with a high average Coulombic efficiency of 99%. With the advantages of rapid and controllable fabrication of the LBL coating film, the multifunctional architecture developed in this study should inspire the design of other lithium-sulfur cathodes with unique physical and chemical properties.

ADHESIVES WITH DIFFERENT PHS: EFFECT ON THE MTBS OF CHEMICALLY ACTIVATED AND LIGHT-ACTIVATED COMPOSITES TO HUMAN DENTIN

PubMed Central

Mallmann, André; de Melo, Renata Marques; Estrela, Verbênia; Pelogia, Fernanda; Campos, Laura; Bottino, Marco Antonio; Valandro, Luiz Felipe

2007-01-01

Purpose: To evaluate the bond strength between human dentin and composites, using two light-activated single-bottle total-etch adhesive systems with different pHs combined with chemically activated and light-activated-composites. The tested hypothesis was that the dentin bond strength is not influenced by an adhesive system of low pH, combined with chemically activated or light-activated composites. Material and Method: Flat dentin surfaces of twenty-eight human third molars were allocated in 4 groups (n=7), depending on the adhesive system: (One Step Plus-OS and Prime & Bond NT-PB) and composite (light-activated Filtek Z-100 [Z100] and chemically activated Bisfil 2B [B2B]). Each adhesive system was applied on acid-etched dentin and then one of the composites was added to form a 5 mm-high resin block. The specimens were stored in tap water (37°C/24 h) and sectioned into two axes, x and y. This was done with a diamond disk under coolant irrigation to obtain beams with a cross-section area of approximately 0.8 mm2. Each specimen was then attached to a custom-made device and submitted to the microtensile test (1 mm.min−1). Data were analyzed using two-way ANOVA and Tukey’s tests (p<0.05). Results: The anticipated hypothesis was not confirmed (p<0.0001). The bond strengths (MPa) were not statistically different between the two adhesive systems when light-activated composite was used (OS+Z100 = 24.7±7.1ª; PB+Z100 = 23.8±5.7ª). However, with use of the chemically activated composite (B2B), PB (7.8±3.6b MPa) showed significantly lower dentin bond strengths than OS (32.2±7.6ª). Conclusion: The low pH of the adhesive system can affect the bond of chemically activated composite to dentin. On the other hand, under the present conditions, the low pH did not seem to affect the bond of light-activated composites to dentin significantly. PMID:19089142

Adhesives with different pHs: effect on the MTBS of chemically activated and light-activated composites to human dentin.

PubMed

Mallmann, André; de Melo, Renata Marques; Estrela, Verbênia; Pelogia, Fernanda; Campos, Laura; Bottino, Marco Antonio; Valandro, Luiz Felipe

2007-08-01

To evaluate the bond strength between human dentin and composites, using two light-activated single-bottle total-etch adhesive systems with different pHs combined with chemically activated and light-activated-composites. The tested hypothesis was that the dentin bond strength is not influenced by an adhesive system of low pH, combined with chemically activated or light-activated composites. Flat dentin surfaces of twenty-eight human third molars were allocated in 4 groups (n=7), depending on the adhesive system: (One Step Plus-OS and Prime & Bond NT-PB) and composite (light-activated Filtek Z-100 [Z100] and chemically activated Bisfil 2B [B2B]). Each adhesive system was applied on acid-etched dentin and then one of the composites was added to form a 5 mm-high resin block. The specimens were stored in tap water (37 degrees C/24 h) and sectioned into two axes, x and y. This was done with a diamond disk under coolant irrigation to obtain beams with a cross-section area of approximately 0.8 mm(2). Each specimen was then attached to a custom-made device and submitted to the microtensile test (1 mm*min-1). Data were analyzed using two-way ANOVA and Tukey's tests (p<0.05). The anticipated hypothesis was not confirmed (p<0.0001). The bond strengths (MPa) were not statistically different between the two adhesive systems when light-activated composite was used (OS+Z100 = 24.7+/-7.1 feminine; PB+Z100 = 23.8+/-5.7 feminine). However, with use of the chemically activated composite (B2B), PB (7.8+/-3.6b MPa) showed significantly lower dentin bond strengths than OS (32.2+/-7.6 feminine). The low pH of the adhesive system can affect the bond of chemically activated composite to dentin. On the other hand, under the present conditions, the low pH did not seem to affect the bond of light-activated composites to dentin significantly.

[The discussion of the infiltrative model of chemical knowledge stepping into genetics teaching in agricultural institute or university].

PubMed

Zou, Ping; Luo, Pei-Gao

2010-05-01

Chemistry is an important group of basic courses, while genetics is one of the important major-basic courses in curriculum of many majors in agricultural institutes or universities. In order to establish the linkage between the major course and the basic course, the ability of application of the chemical knowledge previously learned in understanding genetic knowledge in genetics teaching is worthy of discussion for genetics teachers. In this paper, the authors advocate to apply some chemical knowledge previously learned to understand genetic knowledge in genetics teaching with infiltrative model, which could help students learn and understand genetic knowledge more deeply. Analysis of the intrinsic logistic relationship among the knowledge of different courses and construction of the integral knowledge network are useful for students to improve their analytic, comprehensive and logistic abilities. By this way, we could explore a new teaching model to develop the talents with new ideas and comprehensive competence in agricultural fields.

Detailed chemical composition of classical Cepheids in the LMC cluster NGC 1866 and in the field of the SMC

NASA Astrophysics Data System (ADS)

Lemasle, B.; Groenewegen, M. A. T.; Grebel, E. K.; Bono, G.; Fiorentino, G.; François, P.; Inno, L.; Kovtyukh, V. V.; Matsunaga, N.; Pedicelli, S.; Primas, F.; Pritchard, J.; Romaniello, M.; da Silva, R.

2017-12-01

Context. Cepheids are excellent tracers of young stellar populations. They play a crucial role in astrophysics as standard candles. The chemistry of classical Cepheids in the Milky Way is now quite well-known, however despite a much larger sample, the chemical composition of Magellanic Cepheids has been only scarcely investigated. Aims: For the first time, we study the chemical composition of several Cepheids located in the same populous cluster: NGC 1866, in the Large Magellanic Cloud (LMC). To also investigate the chemical composition of Cepheids at lower metallicity, we look at four targets located in the Small Magellanic Cloud (SMC). Our sample allows us to increase the number of Cepheids with known metallicities in the LMC/SMC by 20%/25% and the number of Cepheids with detailed chemical composition in the LMC/SMC by 46%/50%. Methods: We use canonical spectroscopic analysis to determine the chemical composition of Cepheids and provide abundances for a good number of α, iron-peak, and neutron-capture elements. Results: We find that six Cepheids in the LMC cluster NGC 1866 have a very homogeneous chemical composition, also consistent with red giant branch (RGB) stars in the cluster. Period-age relations that include no or average rotation indicate that all the Cepheids in NGC 1866 have a similar age and therefore belong to the same stellar population. Our results are in good agreement with theoretical models accounting for luminosity and radial velocity variations. Using distances based on period-luminosity relations in the near- or mid-infrared, we investigate for the first time the metallicity distribution of the young population in the SMC in the depth direction. Preliminary results show no metallicity gradient along the SMC main body, but our sample is small and does not contain Cepheids in the inner few degrees of the SMC. Based on observations collected at the European Organisation for Astronomical Research in the Southern Hemisphere under ESO programme 082.D-0792(B).

Consumer product chemical weight fractions from ingredient lists

EPA Science Inventory

Assessing human exposures to chemicals in consumer products requires composition information. However, comprehensive composition data for products in commerce are not generally available. Many consumer products have reported ingredient lists that are constructed using specific gu...

The Chemical Composition of Maple Syrup

ERIC Educational Resources Information Center

Ball, David W.

2007-01-01

Maple syrup is one of several high-sugar liquids that humans consume. However, maple syrup is more than just a concentrated sugar solution. Here, we review the chemical composition of maple syrup. (Contains 4 tables and 1 figure.)

Chemical investigations of male and female leaf extracts from Schinus molle L.

PubMed

Garzoli, Stefania; Laghezza Masci, Valentina; Turchetti, Giovanni; Pesci, Lorenzo; Tiezzi, Antonio; Ovidi, Elisa

2018-05-29

The pepper-tree Schinus molle is an evergreen ornamental plant with various and diversified list of medical uses. In this article we analysed the chemical composition of male and female leaves of this plant during the off-flowering and flowering seasons. The leaf extracts were obtained by using a sequential extraction with solvents of different polarities and the chemical composition was investigated by GC-MS. The results showed a total of twenty-three components, in which elemol is the most abundant constituent followed by bicyclogermacrene, γ-eudesmol, α-eudesmol, β-eudesmol and isocalamendiol. The petroleum ether and diethyl ether extracts from male and female flowering and off-flowering leaves consisted of sesquiterpene hydrocarbons as a major constituent followed by monoterpene hydrocarbons, while the acetone extracts showed a different composition. The obtained results show differences in the chemical composition between male and female and flowering and not flowering.

Essential Oil Composition of Phagnalon sordidum (L.) from Corsica, Chemical Variability and Antimicrobial Activity.

PubMed

Brunel, Marion; Vitrac, Caroline; Costa, Jean; Mzali, Fatima; Vitrac, Xavier; Muselli, Alain

2016-03-01

The chemical composition of Phagnalon sordidum (L.) essential oil was investigated for the first time using gas chromatography and chromatography/mass spectrometry. Seventy-six compounds, which accounted for 87.9% of the total amount, were identified in a collective essential oil of P. sordidum from Corsica. The main essential oil components were (E)-β-caryophyllene (14.4%), β-pinene (11.0%), thymol (9.0%), and hexadecanoic acid (5.3%). The chemical compositions of essential oils from 19 Corsican locations were investigated. The study of the chemical variability using statistical analysis allowed identifying direct correlation between the three populations of P. sordidum widespread in Corsica and the essential oil compositions they produce. The in vitro antimicrobial activity of P. sordidum essential oil was evaluated and it exhibited a notable activity on a large panel of clinically significant microorganisms. © 2016 Verlag Helvetica Chimica Acta AG, Zürich.

Surface abundance and the hunt for stratification in chemically peculiar hot subdwarfs: PG 0909+276 and UVO 0512-08

NASA Astrophysics Data System (ADS)

Wild, J. F.; Jeffery, C. S.

2018-01-01

Edelmann identified two chemically peculiar hot subdwarfs, PG 0909+276 and UVO 0512-08, as having very high overabundances of iron-group elements. We obtained high-resolution ultraviolet spectroscopy in order to measure abundances of species not observable in the optical, and to seek evidence for chemical stratification in the photosphere. Abundances were measured in three wavelength regions; the optical 3900-6900 Å range was re-analysed to confirm consistency with that analysed by Edelmann. Ultraviolet spectra were obtained with the Space Telescope Imaging Spectrograph on the Hubble Space Telescope, covering the far-UV (1140-1740 Å) and the near-UV (1740-2500 Å). We computed a grid of theoretical local thermodynamic equilibrium spectra to find basic parameters (effective temperatures, surface gravity, surface hydrogen and helium fractions). We measured abundances using a spectral-synthesis approach in each wavelength range. We confirm that several iron-group metals are highly enriched, including cobalt, copper and zinc, relative to typical sdB stars. We detect gallium, germanium, tin and lead, similar to analysis of ultraviolet spectra of some other sdB stars. Our results confirm that PG 0909+276 and UVO 0512-08 exhibit peculiarities which make them distinct from both the normal H-rich sdB and intermediate He-rich sdB stars. The process which leads to this particular composition has still to be identified.

Modifications of Ti-6Al-4V surfaces by direct-write laser machining of linear grooves

NASA Astrophysics Data System (ADS)

Ulerich, Joseph P.; Ionescu, Lara C.; Chen, Jianbo; Soboyejo, Winston O.; Arnold, Craig B.

2007-02-01

As patients who receive orthopedic implants live longer and opt for surgery at a younger age, the need to extend the in vivo lifetimes of these implants has grown. One approach is to pattern implant surfaces with linear grooves, which elicit a cellular response known as contact guidance. Lasers provide a unique method of generating these surface patterns because they are capable of modifying physical and chemical properties over multiple length scales. In this paper we explore the relationship between surface morphology and laser parameters such as fluence, pulse overlap (translation distance), number of passes, and machining environment. We find that using simple procedures involving multiple passes it is possible to manipulate groove properties such as depth, shape, sub-micron roughness, and chemical composition of the Ti-6Al-4V oxide layer. Finally, we demonstrate this procedure by machining several sets of grooves with the same primary groove parameters but varied secondary characteristics. The significance of the secondary groove characteristics is demonstrated by preliminary cell studies indicating that the grooves exhibit basic features of contact guidance and that the cell proliferation in these grooves are significantly altered despite their similar primary characteristics. With further study it will be possible to use specific laser parameters during groove formation to create optimal physical and chemical properties for improved osseointegration.

Cell adhesion and growth on ultrananocrystalline diamond and diamond-like carbon films after different surface modifications

NASA Astrophysics Data System (ADS)

Miksovsky, J.; Voss, A.; Kozarova, R.; Kocourek, T.; Pisarik, P.; Ceccone, G.; Kulisch, W.; Jelinek, M.; Apostolova, M. D.; Reithmaier, J. P.; Popov, C.

2014-04-01

Diamond and diamond-like carbon (DLC) films possess a set of excellent physical and chemical properties which together with a high biocompatibility make them attractive candidates for a number of medical and biotechnological applications. In the current work thin ultrananocrystalline diamond (UNCD) and DLC films were comparatively investigated with respect to cell attachment and proliferation after different surface modifications. The UNCD films were prepared by microwave plasma enhanced chemical vapor deposition, the DLC films by pulsed laser deposition (PLD). The films were comprehensively characterized with respect to their basic properties, e.g. crystallinity, morphology, chemical bonding nature, etc. Afterwards the UNCD and DLC films were modified applying O2 or NH3/N2 plasmas and UV/O3 treatments to alter their surface termination. The surface composition of as-grown and modified samples was studied by X-ray photoelectron spectroscopy (XPS). Furthermore the films were characterized by contact angle measurements with water, formamide, 1-decanol and diiodomethane; from the results obtained the surface energy with its dispersive and polar components was calculated. The adhesion and proliferation of MG63 osteosarcoma cells on the different UNCD and DLC samples were assessed by measurement of the cell attachment efficiency and MTT assays. The determined cell densities were compared and correlated with the surface properties of as-deposited and modified UNCD and DLC films.

Metal organic chemical vapor deposition of 111-v compounds on silicon

DOEpatents

Vernon, Stanley M.

1986-01-01

Expitaxial composite comprising thin films of a Group III-V compound semiconductor such as gallium arsenide (GaAs) or gallium aluminum arsenide (GaAlAs) on single crystal silicon substrates are disclosed. Also disclosed is a process for manufacturing, by chemical deposition from the vapor phase, epitaxial composites as above described, and to semiconductor devices based on such epitaxial composites. The composites have particular utility for use in making light sensitive solid state solar cells.

Chemical Composition Variability of Essential Oils of Daucus gracilis Steinh. from Algeria.

PubMed

Benyelles, Batoul; Allali, Hocine; Dib, Mohamed El Amine; Djabou, Nassim; Paolini, Julien; Costa, Jean

2017-06-01

The chemical compositions of 20 Algerian Daucus gracilis essential oils were investigated using GC-FID, GC/MS, and NMR analyses. Altogether, 47 compounds were identified, accounting for 90 - 99% of the total oil compositions. The main components were linalool (18; 12.5 - 22.6%), 2-methylbutyl 2-methylbutyrate (20; 9.2 - 20.2%), 2-methylbutyl isobutyrate (10; 4.2 - 12.2%), ammimajane (47; 2.6 - 37.1%), (E)-β-ocimene (15; 0.2 - 12.8%) and 3-methylbutyl isovalerate (19; 3.3 - 9.6%). The chemical composition of the essential oils obtained from separate organs was also studied. GC and GC/MS analysis of D. gracilis leaves and flowers allowed identifying 47 compounds, amounting to 92.3% and 94.1% of total oil composition, respectively. GC and GC/MS analysis of D. gracilis leaf and flower oils allowed identifying linalool (22.7%), 2-methylbutyl 2-methylbutyrate (18.9%), 2-methylbutyl isovalerate (13.6%), ammimajane (10.4%), 3-methylbutyl isovalerate (10.3%), (E)-β-ocimene (8.4%) and isopentyl 2-methylbutyrate (8.1%) as main components. The chemical variability of the Algerian oil samples was studied using statistical analysis, which allowed the discrimination of three main Groups. A direct correlation between the altitudes, nature of soils and the chemical compositions of the D. gracilis essential oils was evidenced. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Discovering More Chemical Concepts from 3D Chemical Information Searches of Crystal Structure Databases

ERIC Educational Resources Information Center

Rzepa, Henry S.

2016-01-01

Three new examples are presented illustrating three-dimensional chemical information searches of the Cambridge structure database (CSD) from which basic core concepts in organic and inorganic chemistry emerge. These include connecting the regiochemistry of aromatic electrophilic substitution with the geometrical properties of hydrogen bonding…

Chemical Mixtures Health Risk Assessment: Overview of Exposure Assessment, Whole Mixtures Assessments; Basic Concepts

EPA Science Inventory

This problems-based, half-day, introductory workshop focuses on methods to assess health risks posed by exposures to chemical mixtures in the environment. Chemical mixtures health risk assessment methods continue to be developed and evolve to address concerns over health risks f...

Proof test methodology for composites

NASA Technical Reports Server (NTRS)

Wu, Edward M.; Bell, David K.

1992-01-01

The special requirements for proof test of composites are identified based on the underlying failure process of composites. Two proof test methods are developed to eliminate the inevitable weak fiber sites without also causing flaw clustering which weakens the post-proof-test composite. Significant reliability enhancement by these proof test methods has been experimentally demonstrated for composite strength and composite life in tension. This basic proof test methodology is relevant to the certification and acceptance of critical composite structures. It can also be applied to the manufacturing process development to achieve zero-reject for very large composite structures.

A study of material composition disclosure practices in green footwear products.

PubMed

Jacques, Jocelise J; Guimarães, Lia B M

2012-01-01

This work is based on the study of pioneering sustainable product development initiatives, and the analysis was guided by the cradle-to-cradle concept, which sees the waste of a given process as raw material for another, just like it happens in nature. Several studies on human factors have focused on factory conditions and workers dealing with product assembly. This research, however, relates more to consumer behavior, product use and end-of-life. The purchase of more environmentally- friendly products, in particular, is heavily influenced by the information made available by the companies. In this scenario, this article discusses three early but notable efforts on green product development, focusing on the disclosure practices adopted by the companies regarding the composition of their products. Research and data collection has focused on the footwear industry, whose products satisfy a basic human need and are ubiquitous worldwide. The use of hazardous materials and chemicals in shoe manufacturing, particularly the use of chromium - a highly toxic element - in addition to toxic solvents and adhesives and non-recyclable synthetic materials can pose serious risks to human health and the environment, even though the consumer usually is not aware of all the relevant characteristics of this kind of product.

Physical and Chemical Properties of Sintering Red Mud and Bayer Red Mud and the Implications for Beneficial Utilization

PubMed Central

Wang, Ping; Liu, Dong-Yan

2012-01-01

Performances of two common types of red mud, Bayer red mud and Sintering red mud, were investigated in this research. Their compositions, mechanical properties and microstructure characterization were measured through XRD, TG and SEM analysis. Their shear strength, particle size, density and hydraulic characteristics also had been performed. Huge differences between the basic mineral types of these two kinds of red mud also can be found. The comparison of compositions shows that CaCO3 content in Sintering red mud is higher, Bayer red mud has more hazardous elements such as As, Pb and Hg and both have a high concentration of radioactivity. The micro particle of Bayer red mud is finer and more disperse, but the Sintering red mud has higher shear strength. Combining the TG and hydraulic characteristics analysis, it can be shown that Bayer red mud has higher value of water content and Sintering red mud has higher hydraulic conductivity. The paper then illustrates that Sintering red mud can become the main filling material of supporting structure of red mud stocking yard. Bayer red mud has a high reuse value and also can be used as a mixing material of masonry mortar.

Ion implantation modified stainless steel as a substrate for hydroxyapatite deposition. Part II. Biomimetic layer growth and characterization.

PubMed

Pramatarova, L; Pecheva, E; Krastev, V

2007-03-01

The interest in stainless steel as a material widely used in medicine and dentistry has stimulated extensive studies on improving its bone-bonding properties. AISI 316 stainless steel is modified by a sequential ion implantation of Ca and P ions (the basic ions of hydroxyapatite), and by Ca and P implantation and subsequent thermal treatment in air (600( composite function)C, 1 h). This paper investigates the ability of the as-modified surfaces to induce hydroxyapatite deposition by using a biomimetic approach, i.e. immersion in a supersaturated aqueous solution resembling the human blood plasma (the so-called simulated body fluid). We describe our experimental procedure and results, and discuss the physico-chemical properties of the deposed hydroxyapatite on the modified stainless steel surfaces. It is shown that the implantation of a selected combination of ions followed by the applied methodology of the sample soaking in the simulated body fluid yield the growth of hydroxyapatite layers with composition and structure resembling those of the bone apatite. The grown layers are found suitable for studying the process of mineral formation in nature (biomineralization).

Chemical recycling of scrap composites

NASA Technical Reports Server (NTRS)

Allred, Ronald E.; Salas, Richard M.

1994-01-01

There are no well-developed technologies for recycling composite materials other than grinding to produce fillers. New approaches are needed to reclaim these valuable resources. Chemical or tertiary recycling, conversion of polymers into low molecular weight hydrocarbons for reuse as chemicals or fuels, is emerging as the most practical means for obtaining value from waste plastics and composites. Adherent Technologies is exploring a low-temperature catalytic process for recycling plastics and composites. Laboratory results show that all types of plastics, thermosets as well as thermoplastics, can be converted in high yields to valuable hydrocarbon products. This novel catalytic process runs at 200 C, conversion times are rapid, the process is closed and, thus, nonpolluting, and no highly toxic gas or liquid products have been observed so no negative environmental impact will result from its implementation. Tests on reclamation of composite materials show that epoxy, imide, and engineering thermoplastic matrices can be converted to low molecular weight hydrocarbons leaving behind the reinforcing fibers for reuse as composite reinforcements in secondary, lower-performance applications. Chemical recycling is also a means to dispose of sensitive or classified organic materials without incineration and provides a means to eliminate or reduce mixed hazardous wastes containing organic materials.

Biological resistance of polyethylene composites made with chemically modified fiber or flour

Treesearch

Rebecca E. Ibach; Craig M. Clemons

2002-01-01

The role of moisture in the biological decay of wood-plastic composites was investigated. Southern pine wood fiber and ponderosa pine wood flour were chemically modified using either acetic anhydride (AA), butylene oxide (BO), or propylene oxide (PO). A 50:50 mixture of high density polyethylene and either chemically modified fiber or flour, or untreated fiber or flour...

Correlation of rocket propulsion fuel properties with chemical composition using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry followed by partial least squares regression analysis.

PubMed

Kehimkar, Benjamin; Hoggard, Jamin C; Marney, Luke C; Billingsley, Matthew C; Fraga, Carlos G; Bruno, Thomas J; Synovec, Robert E

2014-01-31

There is an increased need to more fully assess and control the composition of kerosene-based rocket propulsion fuels such as RP-1. In particular, it is critical to make better quantitative connections among the following three attributes: fuel performance (thermal stability, sooting propensity, engine specific impulse, etc.), fuel properties (such as flash point, density, kinematic viscosity, net heat of combustion, and hydrogen content), and the chemical composition of a given fuel, i.e., amounts of specific chemical compounds and compound classes present in a fuel as a result of feedstock blending and/or processing. Recent efforts in predicting fuel chemical and physical behavior through modeling put greater emphasis on attaining detailed and accurate fuel properties and fuel composition information. Often, one-dimensional gas chromatography (GC) combined with mass spectrometry (MS) is employed to provide chemical composition information. Building on approaches that used GC-MS, but to glean substantially more chemical information from these complex fuels, we recently studied the use of comprehensive two dimensional (2D) gas chromatography combined with time-of-flight mass spectrometry (GC×GC-TOFMS) using a "reversed column" format: RTX-wax column for the first dimension, and a RTX-1 column for the second dimension. In this report, by applying chemometric data analysis, specifically partial least-squares (PLS) regression analysis, we are able to readily model (and correlate) the chemical compositional information provided by use of GC×GC-TOFMS to RP-1 fuel property information such as density, kinematic viscosity, net heat of combustion, and so on. Furthermore, we readily identified compounds that contribute significantly to measured differences in fuel properties based on results from the PLS models. We anticipate this new chemical analysis strategy will have broad implications for the development of high fidelity composition-property models, leading to an improved approach to fuel formulation and specification for advanced engine cycles. Copyright © 2014 Elsevier B.V. All rights reserved.

Exploring the Mastery of French Students in Using Basic Notions of the Language of Chemistry

ERIC Educational Resources Information Center

Canac, Sophie; Kermen, Isabelle

2016-01-01

Learning chemistry includes learning the language of chemistry (names, formulae, symbols, and chemical equations) which has to be done in connection with the other areas of chemical knowledge. In this study we investigate how French students understand and use names (of chemical species and common mixtures) and chemical formulae. We set a paper…

The surface chemical reactivity of particles and its impact on human health

NASA Astrophysics Data System (ADS)

Setyan, A.; Sauvain, J. J.; Riediker, M.; Guillemin, M.; Rossi, M. J.

2017-12-01

The chemical composition of the particle-air interface is the gateway to chemical reactions of gases with condensed phase particles. It is of prime importance to understand the reactivity of particles and their interaction with surrounding gases, biological membranes, and solid supports. We used a Knudsen flow reactor to quantify functional groups on the surface of a few selected particle types. This technique is based on a heterogeneous titration reaction between a probe gas and a specific functional group on the particle surface. Six probe gases have been selected for the identification and quantification of important functional groups: N(CH3)3 for the titration of acidic sites, NH2OH for the detection of carbonyl functions (aldehydes and ketones) and/or oxidized sites owing to its strong reducing properties, CF3COOH and HCl for basic sites of different strength, O3 and NO2 for oxidizable groups. We also studied the kinetics of the reactions between particles and probe gases (uptake coefficient γ0). We tested the surface chemical composition and oxidation states of laboratory-generated aerosols (3 amorphous carbons, 2 flame soots, 2 Diesel particles, 2 secondary organic aerosols [SOA], 4 multiwall carbon nanotubes [MWCNT], 3 TiO2, and 2 metal salts) and of aerosols sampled in several bus depots. The sampling of particles in the bus depots was accompanied by the collection of urine samples of mechanics working full-time in these bus depots, and the quantification of 8-hydroxy-2'-deoxyguanosine, a biomarker of oxidative stress. The increase in oxidative stress biomarker levels over a working day was correlated (p<0.05) with the number of olefinic and/or PAH sites on the surface of particles sampled at the bus depots, obtained from O3 uptakes, as well as with the initial uptake coefficient (γ0) of five probe gases used in the field. This correlation with γ0 suggests the idea of competing pathways occurring at the interface of the aerosol particles between the generation of reactive oxygen species (ROS) responsible for oxidative stress and cellular antioxidants.

Continental igneous rock composition: A major control of past global chemical weathering

PubMed Central

Bataille, Clément P.; Willis, Amy; Yang, Xiao; Liu, Xiao-Ming

2017-01-01

The composition of igneous rocks in the continental crust has changed throughout Earth’s history. However, the impact of these compositional variations on chemical weathering, and by extension on seawater and atmosphere evolution, is largely unknown. We use the strontium isotope ratio in seawater [(87Sr/86Sr)seawater] as a proxy for chemical weathering, and we test the sensitivity of (87Sr/86Sr)seawater variations to the strontium isotopic composition (87Sr/86Sr) in igneous rocks generated through time. We demonstrate that the 87Sr/86Sr ratio in igneous rocks is correlated to the epsilon hafnium (εHf) of their hosted zircon grains, and we use the detrital zircon record to reconstruct the evolution of the 87Sr/86Sr ratio in zircon-bearing igneous rocks. The reconstructed 87Sr/86Sr variations in igneous rocks are strongly correlated with the (87Sr/86Sr)seawater variations over the last 1000 million years, suggesting a direct control of the isotopic composition of silicic magmatism on (87Sr/86Sr)seawater variations. The correlation decreases during several time periods, likely reflecting changes in the chemical weathering rate associated with paleogeographic, climatic, or tectonic events. We argue that for most of the last 1000 million years, the (87Sr/86Sr)seawater variations are responding to changes in the isotopic composition of silicic magmatism rather than to changes in the global chemical weathering rate. We conclude that the (87Sr/86Sr)seawater variations are of limited utility to reconstruct changes in the global chemical weathering rate in deep times. PMID:28345044

Composite materials for thermal energy storage: enhancing performance through microstructures.

PubMed

Ge, Zhiwei; Ye, Feng; Ding, Yulong

2014-05-01

Chemical incompatibility and low thermal conductivity issues of molten-salt-based thermal energy storage materials can be addressed by using microstructured composites. Using a eutectic mixture of lithium and sodium carbonates as molten salt, magnesium oxide as supporting material, and graphite as thermal conductivity enhancer, the microstructural development, chemical compatibility, thermal stability, thermal conductivity, and thermal energy storage performance of composite materials are investigated. The ceramic supporting material is essential for preventing salt leakage and hence provides a solution to the chemical incompatibility issue. The use of graphite gives a significant enhancement on the thermal conductivity of the composite. Analyses suggest that the experimentally observed microstructural development of the composite is associated with the wettability of the salt on the ceramic substrate and that on the thermal conduction enhancer. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation of novel multi-walled carbon nanotubes nanocomposite adsorbent via RAFT technique for the adsorption of toxic copper ions.

PubMed

Hosseinzadeh, Hossein; Pashaei, Shahryar; Hosseinzadeh, Soleyman; Khodaparast, Zahra; Ramin, Sonia; Saadat, Younes

2018-05-31

In the present work, polymer-coated multiwalled carbon nanotube (MWCNT) was prepared via RAFT method. First, a novel trithiocarbonate-based RAFT agent was prepared attached chemically into the surface of MWCNT. In addition, the RAFT co-polymerization of acrylic acid and acrylamide monomers was conducted through the prepared RAFT agent. In the next age, the surface morphology and chemical properties of the prepared components were fully examined by using FTIR, 1 HNMR, SEM, TEM, XRD and TGA/DTG techniques. Finally, the modified MWCNT composite was employed as an excellent adsorbent for the adsorption of copper (II) ions. The results indicated that ion adsorption basically relies on adsorbing time, solution pH, initial copper concentration, and adsorbent dosage. Further, the adsorption kinetics and isotherm analysis demonstrated that the adsorption mode was fitted with the pseudo-second-order and Langmuir isotherm models, respectively. Based on the results of thermodynamic study, the ion adsorption process was endothermic and spontaneous. Finally, based on the experimental results, the surface functionalized MWCNT with hydrophilic groups could be successfully used as a promising selective adsorbent material in wastewater treatment. Copyright © 2018 Elsevier B.V. All rights reserved.

Chemical characteristics of ambient aerosols contributed by cooking process at Noorpur village near Delhi (India)

NASA Astrophysics Data System (ADS)

Singh, Sudha; Kumar, Bablu; Gupta, Gyan Prakash; Kulshrestha, U. C.

2013-05-01

Combustion of fuels such as wood, crop residue and dung cakes etc. is one of the major sources of air pollution in developing countries. These fuels are still used commonly for cooking purpose in rural India. This study investigates the chemical composition of the ambient aerosols during cooking hours at a village called Noorpur (28.470 N, 77.030 E) which lies near Delhi city. Aerosol sampling was carried out during August 2011-May 2012 by using handy sampler (Envirotech model APM 821) installed at the terrace of a building (˜6m). The samples were collected on 8 hourly basis using Teflon filters. The water extract of these filters was analyzed for major anions (F-, Cl-, NO3-, SO42-) and major cations (Na+, NH4+, K+, Ca2+ Mg2+) by ion chromatography (Metrohm 883 Basic IC Plus). Results highlighted that cooking process contributed significant amount of SO42- and K+ṡ. Biomass burning is considered as a potential source of K+ in air. The high concentration of SO42- might be due to oxidation of SO2 contributed by the combustion of dung cakes. Further, the detailed results will be discussed during the conference.

Heavy metals in MSW incineration fly ashes

NASA Astrophysics Data System (ADS)

Ferreira, C.; Ribeiro, A.; Ottosen, L.

2003-05-01

Incineration is a common solution for dealing with the increasing amount of municipal solid waste (MSW). During the process, the heavy metals initially present in the waste go through several transformations, ending up in combustion products, such as fly ash. This article deals with some issues related to the combustion of MSW and the formation of fly ash, especially in what concerns heavy metals. Treatment of the flue gas in air pollution control equipment plays an important role and the basic processes to accomplish this are explained. Fly ash from a semi-dry flue gas treatment system is characterized regarding its physical-chemical properties: pH, solubility, chemical composition, and leaching, amongst others. Results indicate a high alkalinity and the presence of large amounts of calcium, chlorides, sulfates, carbonates, sodium and potassium. Metal concentrations in fly ash are: 6,2g/kg for zinc, 2,4g/kg for lead, 1,7g/kg for iron, and 7,9g/kg for magnesium. Copper, manganese, chromium and cadmium are also present with 546, 338, 104 and 91mg/kg of fly ash, respectively. These results are extremely important in subsequent studies on the treatment of fly ash.

Laboratory experiments in the study of the chemistry of the outer planets.

PubMed

Scattergood, T W

1987-01-01

The investigation of chemical evolution of bodies in our solar system has, in the past, included observations, theoretical modeling, and laboratory simulations. Of these programs, the last one has been the most criticized due to the inherent difficulties in accurately recreating alien environments in the laboratory. Processes such as wall reactions and changes in chemistry due to difficulties in achieving realistic conditions of temperature, pressure, composition, and energy flux may yield results which are not truly representative of the systems being modeled. However, many laboratory studies have been done which have yielded data useful in planetary science. Gross simulations of atmospheric chemistry have placed constraints on the nature of complex molecules expected in planetary atmospheres. More precise studies of specific chemical processes have provided information about the sources and properties of product gases and aerosols. Determinations of basic properties such as spectral features and reaction rate constants yield data useful in the interpretation of observations and in computational modeling. Alone, and in conjunction with modeling, laboratory experiments will continue to be used to further our understanding of the outer solar system, and some experiments that need to be done are listed.

Chemical and functional properties of the different by-products of artichoke (Cynara scolymus L.) from industrial canning processing.

PubMed

Ruiz-Cano, Domingo; Pérez-Llamas, Francisca; Frutos, María José; Arnao, Marino B; Espinosa, Cristóbal; López-Jiménez, José Ángel; Castillo, Julián; Zamora, Salvador

2014-10-01

In this study, the basic chemical composition and functional properties of six by-product fractions collected from different steps of artichoke industrial processing were evaluated. Fractions differed in thermal treatment, the bract position in the artichoke head and the cutting size. Contents of moisture, ash, protein, fat, dietary fibre, inulin, total phenolics, total flavonoids, caffeoyl derivatives and flavones were analysed. Antioxidant activity values were also determined. All assessed artichoke by-product fractions contained high-dietary fibre (53.6-67.0%) and low fat (2.5-3.7%). Artichoke by-product fractions contained high levels of inulin, especially in the boiled inner bracts (30%). Total phenolic and flavonoid contents and antioxidant activity (153-729 μmol gallic acid equivalents, 6.9-19.2 μmol quercetin equivalents and 85-234 μmol ascorbic acid equivalents per gram of dry matter, respectively) varied widely with the bract positions in the artichoke head and the thermal treatments. The more interesting fractions for use as functional ingredients were those situated closer to the artichoke heart and thermally treated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fluidized bed gasification of industrial solid recovered fuels.

PubMed

Arena, Umberto; Di Gregorio, Fabrizio

2016-04-01

The study evaluates the technical feasibility of the fluidized bed gasification of three solid recovered fuels (SRFs), obtained as co-products of a recycling process. The SRFs were pelletized and fed to a pilot scale bubbling fluidized bed reactor, operated in gasification and co-gasification mode. The tests were carried out under conditions of thermal and chemical steady state, with a bed of olivine particles and at different values of equivalence ratio. The results provide a complete syngas characterization, in terms of its heating value and composition (including tars, particulates, and acid/basic pollutants) and of the chemical and physical characterization of bed material and entrained fines collected at the cyclone outlet. The feasibility of the fluidized bed gasification process of the different SRFs was evaluated with the support of a material and substance flow analysis, and a feedstock energy analysis. The results confirm the flexibility of fluidized bed reactor, which makes it one of the preferable technologies for the gasification of different kind of wastes, even in co-gasification mode. The fluidized bed gasification process of the tested SRFs appears technically feasible, yielding a syngas of valuable quality for energy applications in an appropriate plant configuration. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Chemical components from essential oil of Pandanus amaryllifolius leaves].

PubMed

Chen, Xiao-Kai; Ge, Fa-Huan

2014-04-01

To analyze the chemical compositions of Pandanus amaryllifolius leaves essential oil extracted by steam distillation. The essential oil of Pandanus amaryllifolius leaves was analyzed by gas chromatography-mass spectrum, and the relative content of each component was determined by area normalization method. 128 peaks were separated and 95 compounds were identified, which weighed 97.75%. The main chemical components of the essential oil were phytol (42.15%), squalene (16.81%), what's more pentadecanal (6.17%), pentadecanoic acid (4.49%), 3, 7, 11, 15-tetramethyl-2-hexadecen-1-ol (3.83%), phytone (2.05%) and the other 74 chemical compositions were firstly identified from the essential oil of Pandanus amaryllifolius leaves. The chemical compositions of Pandanu samaryllifolius leaves essential oil was systematically, deeply isolated and identified for the first time. This experiment has provided scientific foundation for further utilization of Pandanus amaryllifolius leaves.

The road for nanomaterials industry: a review of carbon nanotube production, post-treatment, and bulk applications for composites and energy storage.

PubMed

Zhang, Qiang; Huang, Jia-Qi; Qian, Wei-Zhong; Zhang, Ying-Ying; Wei, Fei

2013-04-22

The innovation on the low dimensional nanomaterials brings the rapid growth of nano community. Developing the controllable production and commercial applications of nanomaterials for sustainable society is highly concerned. Herein, carbon nanotubes (CNTs) with sp(2) carbon bonding, excellent mechanical, electrical, thermal, as well as transport properties are selected as model nanomaterials to demonstrate the road of nanomaterials towards industry. The engineering principles of the mass production and recent progress in the area of CNT purification and dispersion are described, as well as its bulk application for nanocomposites and energy storage. The environmental, health, and safety considerations of CNTs, and recent progress in CNT commercialization are also included. With the effort from the CNT industry during the past 10 years, the price of multi-walled CNTs have decreased from 45 000 to 100 $ kg(-1) and the productivity increased to several hundred tons per year for commercial applications in Li ion battery and nanocomposites. When the prices of CNTs decrease to 10 $ kg(-1) , their applications as composites and conductive fillers at a million ton scale can be anticipated, replacing conventional carbon black fillers. Compared with traditional bulk chemicals, the controllable synthesis and applications of CNTs on a million ton scale are still far from being achieved due to the challenges in production, purification, dispersion, and commercial application. The basic knowledge of growth mechanisms, efficient and controllable routes for CNT production, the environmental and safety issues, and the commercialization models are still inadequate. The gap between the basic scientific research and industrial development should be bridged by multidisciplinary research for the rapid growth of CNT nano-industry. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The LATL as locus of composition: MEG evidence from English and Arabic.

PubMed

Westerlund, Masha; Kastner, Itamar; Al Kaabi, Meera; Pylkkänen, Liina

2015-02-01

Neurolinguistic investigations into the processing of structured sentences as well as simple adjective-noun phrases point to the left anterior temporal lobe (LATL) as a leading candidate for basic linguistic composition. Here, we characterized the combinatory profile of the LATL over a variety of syntactic and semantic environments, and across two languages, English and Arabic. The contribution of the LATL was investigated across two types of composition: the optional modification of a predicate (modification) and the satisfaction of a predicate's argument position (argument saturation). Target words were presented during MEG recordings, either in combinatory contexts (e.g. "eats meat") or in non-combinatory contexts (preceded by an unpronounceable consonant string, e.g. "xqkr meat"). Across both languages, the LATL showed increased responses to words in combinatory contexts, an effect that was robust to composition type and word order. Together with related findings, these results solidify the role of the LATL in basic semantic composition. Copyright © 2014 Elsevier Inc. All rights reserved.

WOOD STOVE EMISSIONS: PARTICLE SIZE AND CHEMICAL COMPOSITION

EPA Science Inventory

The report summarizes wood stove particle size and chemical composition data gathered to date. [NOTE: In 1995, EPA estimated that residential wood combustion (RWC), including fireplaces, accounted for a significant fraction of national particulate matter with aerodynamic diameter...

Application of cementitious composites in mechanical engineering

NASA Astrophysics Data System (ADS)

Fediuk, R. S.; Ibragimov, R. A.; Lesovik, V. S.; Akopian, A. K.; Teleshev, A. A.; Khankhabaev, L. R.; Ivanov, A. S.

2018-03-01

The paper presents the results of the development of composite fiber-reinforced concrete for use as basic parts of machine-tools and machines. It was revealed that the additions of fly ash and limestone significantly reduce the cracking of concrete. Thus, a clear relationship between the properties of concrete and the features of the structure of cement stone was revealed. The strength and crack resistance of concrete is increased due to an increase in the number of low-basic calcium hydrosilicates, as well as increased gel porosity and reduced capillary porosity (especially at the submicroscopic level).

Composition of matter in the heliosphere

NASA Astrophysics Data System (ADS)

Bochsler, Peter

2009-03-01

The Sun is by far the largest reservoir of matter in the solar system and contains more than 99% of the mass of the solar system. Theories on the formation of the solar system maintain that the gravitational collapse is very efficient and that typically not more than one tenth from the solar nebula is lost during the formation process. Consequently, the Sun can be considered as a representative sample of interstellar matter taken from a well mixed reservoir 4.6 Gy ago, at about 8 kpc from the galactic center. At the same time, the Sun is also a faithful witness of the composition of matter at the beginning of the evolution of the solar system and the formation of planets, asteroids, and comets. Knowledge on the solar composition and a fair account of the related uncertainties is relevant for many fields in astrophysics, planetary sciences, cosmo- and geochemistry. Apart from the basic interest in the chemical evolution of the galaxy and the solar system, compositional studies have also led to many applications in space research, i.e., it has helped to distinguish between different components of diffuse heliospheric matter. The elemental, isotopic, and charge state composition of heliospheric particles (solar wind, interstellar neutrals, pickup ions) has been used for a multitude of applications, such as tracing the source material, constraining parameters for models of the acceleration processes, and of the transport through the interplanetary medium. It is important to realize, that the two mainstream applications, as outlined above - geochemistry and cosmochemistry on one side, and tracing of heliospheric processes on the other side - are not independent of each other. Understanding the physical processes, e.g., of the fractionation of the solar wind, is crucial for the interpretation of compositional data; on the other hand, reliable information on the source composition is the basis for putting constraints on models of the solar wind fractionation.

Analysis of the Relationships between Waste Cooking Oil Qualities and Rejuvenated Asphalt Properties

PubMed Central

Zhang, Dong; Chen, Meizhu; Wu, Shaopeng; Liu, Jingxiang; Amirkhanian, Serji

2017-01-01

Waste cooking oil (WCO), in many cases, can rejuvenate aged asphalt and restore its properties. However, the influence of WCO qualities on rejuvenation behaviors of aged asphalt has not been investigated in detail. The objective of this paper was to evaluate the effects of WCO viscosity and acid value on the basic, rheological, and chemical properties of a typical rejuvenated asphalt. Penetration, ring and ball (R and B) softening point, and ductility were tested to evaluate the influence of WCO qualities on basic properties of rejuvenated asphalts. Then, the rheological properties of rejuvenated asphalt were characterized based on rotational viscometer (RV), dynamic shear rheometer (DSR), and bending beam rheometer (BBR) test results. Further, SARA (saturates, aromatics, resins, and asphaltenes) fraction analysis and Fourier transform infrared spectroscopy (FTIR) tests were performed to investigate the effects of WCO qualities on asphalt chemical composition. Finally, grey correlation coefficients were calculated and the relationships between WCO qualities and rejuvenated asphalt properties were quantitatively evaluated. The experimental results indicated that WCO qualities influence the rejuvenation behaviors of aged asphalt significantly, and the WCO with higher qualities (low acid value and viscosity, as defined in this research) tends to achieve better rejuvenation effects. Based on the results of grey correlation analyses, the acid value is, relatively, a better indicator than viscosity in predicting the rejuvenation efficiency of WCO. The rejuvenation thresholds of WCO are varied with the categories of properties of rejuvenated asphalts, and WCO with an acid value of 0.4–0.7 mg KOH/g, or a viscosity of 140–540 mm2/s, can meet all of the performance requirements for asphalt rejuvenation used in this research. PMID:28772862

Analysis of the Relationships between Waste Cooking Oil Qualities and Rejuvenated Asphalt Properties.

PubMed

Zhang, Dong; Chen, Meizhu; Wu, Shaopeng; Liu, Jingxiang; Amirkhanian, Serji

2017-05-06

Waste cooking oil (WCO), in many cases, can rejuvenate aged asphalt and restore its properties. However, the influence of WCO qualities on rejuvenation behaviors of aged asphalt has not been investigated in detail. The objective of this paper was to evaluate the effects of WCO viscosity and acid value on the basic, rheological, and chemical properties of a typical rejuvenated asphalt. Penetration, ring and ball (R and B) softening point, and ductility were tested to evaluate the influence of WCO qualities on basic properties of rejuvenated asphalts. Then, the rheological properties of rejuvenated asphalt were characterized based on rotational viscometer (RV), dynamic shear rheometer (DSR), and bending beam rheometer (BBR) test results. Further, SARA (saturates, aromatics, resins, and asphaltenes) fraction analysis and Fourier transform infrared spectroscopy (FTIR) tests were performed to investigate the effects of WCO qualities on asphalt chemical composition. Finally, grey correlation coefficients were calculated and the relationships between WCO qualities and rejuvenated asphalt properties were quantitatively evaluated. The experimental results indicated that WCO qualities influence the rejuvenation behaviors of aged asphalt significantly, and the WCO with higher qualities (low acid value and viscosity, as defined in this research) tends to achieve better rejuvenation effects. Based on the results of grey correlation analyses, the acid value is, relatively, a better indicator than viscosity in predicting the rejuvenation efficiency of WCO. The rejuvenation thresholds of WCO are varied with the categories of properties of rejuvenated asphalts, and WCO with an acid value of 0.4-0.7 mg KOH/g, or a viscosity of 140-540 mm²/s, can meet all of the performance requirements for asphalt rejuvenation used in this research.

Combining technologies to create bioactive hybrid scaffolds for bone tissue engineering.

PubMed

Nandakumar, Anandkumar; Barradas, Ana; de Boer, Jan; Moroni, Lorenzo; van Blitterswijk, Clemens; Habibovic, Pamela

2013-01-01

Combining technologies to engineer scaffolds that can offer physical and chemical cues to cells is an attractive approach in tissue engineering and regenerative medicine. In this study, we have fabricated polymer-ceramic hybrid scaffolds for bone regeneration by combining rapid prototyping (RP), electrospinning (ESP) and a biomimetic coating method in order to provide mechanical support and a physico-chemical environment mimicking both the organic and inorganic phases of bone extracellular matrix (ECM). Poly(ethylene oxide terephthalate)-poly(buthylene terephthalate) (PEOT/PBT) block copolymer was used to produce three dimensional scaffolds by combining 3D fiber (3DF) deposition, and ESP, and these constructs were then coated with a Ca-P layer in a simulated physiological solution. Scaffold morphology and composition were studied using scanning electron microscopy (SEM) coupled to energy dispersive X-ray analyzer (EDX) and Fourier Tranform Infrared Spectroscopy (FTIR). Bone marrow derived human mesenchymal stromal cells (hMSCs) were cultured on coated and uncoated 3DF and 3DF + ESP scaffolds for up to 21 d in basic and mineralization medium and cell attachment, proliferation, and expression of genes related to osteogenesis were assessed. Cells attached, proliferated and secreted ECM on all the scaffolds. There were no significant differences in metabolic activity among the different groups on days 7 and 21. Coated 3DF scaffolds showed a significantly higher DNA amount in basic medium at 21 d compared with the coated 3DF + ESP scaffolds, whereas in mineralization medium, the presence of coating in 3DF+ESP scaffolds led to a significant decrease in the amount of DNA. An effect of combining different scaffolding technologies and material types on expression of a number of osteogenic markers (cbfa1, BMP-2, OP, OC and ON) was observed, suggesting the potential use of this approach in bone tissue engineering.

Biodegradable Chitosan Coating Incorporated with Black Pepper Essential Oil for Shelf Life Extension of Common Carp (Cyprinus carpio) during Refrigerated Storage.

PubMed

Moosavi-Nasab, Marzieh; Shad, Ehsan; Ziaee, Esmaeil; Yousefabad, Seyyed Hossein Asadi; Golmakani, Mohammad Taghi; Azizinia, Mehdi

2016-06-01

Chitosan (Ch) coating incorporated with black pepper essential oil (Ch+BPEO) was studied to extend the shelf life of common carp (Cyprinus carpio) during refrigerated storage at 4 ± 1°C. The chemical composition of BPEO was characterized using gas chromatography-mass spectrometry (GC-MS). Antibacterial properties of BPEO were determined by disk diffusion agar, MIC, and MBC. Ch (2% [wt/vol]) and Ch+BPEO (2% [wt/vol] Ch with 1.5% [vol/vol] BPEO) were used for common carp fillet coating. The samples were analyzed periodically for chemical (pH, total volatile basic nitrogen) and microbiological (aerobic plate count, psychrophilic bacteria count, lactic acid bacteria, and Enterobacteriaceae bacterial counts) characteristics during 16 days. The GC-MS results indicated that main components in BPEO were carene, caryophyllene, limonene, β-pinene, and α-pinene. The samples coated with Ch and Ch+BPEO resulted in lower pH and total volatile basic nitrogen values in comparison with the control. The microbiological analysis of fish fillets during refrigerated storage clearly indicated that Ch+BPEO coating significantly reduced the fish fillet microbial load. The aerobic plate count, psychrophilic bacteria count, lactic acid bacteria count, and Enterobacteriaceae bacterial count of samples coated with Ch+BPEO were reduced approximately 4.1, 3.9, 2.3, and 2.8 log CFU/g, respectively, at the end of the storage period. Finally, Ch and Ch+BPEO effectively improved the quality of fish fillet during refrigerated storage and extended the shelf life of fish fillets from 8 to 16 days. Black pepper; Chitosan; Common carp; Essential oil.

NO2 disproportionation for the IR characterisation of basic zeolites.

PubMed

Marie, Olivier; Malicki, Nicolas; Pommier, Catherine; Massiani, Pascale; Vos, Ann; Schoonheydt, Robert; Geerlings, Paul; Henriques, Carlos; Thibault-Starzyk, Fréderic

2005-02-28

NO2 disproportionation on alkaline zeolites is used to generate nitrosonium (NO+) and nitrate ions on the surface, and the infrared vibrations observed are very sensitive to the cation chemical hardness and to the basicity of zeolitic oxygen atoms.

Analysis of LDEF experiment AO187-2 chemical and isotopic measurements of micrometeoroids by secondary ion mass spectrometry

NASA Technical Reports Server (NTRS)

Zinner, Ernst

1995-01-01

#Experiment AO187-2, that was flown on board the Long Duration Exposure Facility(LDEF), was designed to measure the chemical and isotopic compositions of interplanetary dust impinging on the spacecraft from outer space. Information on the nature and composition of orbital debris was also anticipated. The spacecraft maintained a constant orientation with respect to its velocity vector thereby defining leading and trailing edges that faced respectively into and away from the direction of motion. Arrays of individual capture cells each 80.8 sq cm in size and totaling 237 in number were exposed on both the leading and trailing edges of LDEF. Each cell consisted of a pure Ge target surface slightly separated from a thin (2.5 micrometers) metallized plastic 'entrance foil.' The basic concept was that incoming projectiles would penetrate the foil, strike the Ge target plate at high velocity producing a vapor-liquid cloud that would re-deposit material on the underside of the plastic foil. This material would then be analyzed using the sensitive surface analysis technique of Secondary Ion Mass Spectrometry (SIMS). In practice, most of the plastic entrance foils failed during the extended period of orbital exposure probably due to a combination of UV embrittlement, large densities of impact events and (for the leading edge) the effects of atomic oxygen erosion in orbit. However the foils failed gradually and most remained in place on the capture cells for a significant fraction of the duration of the flight . Because most of the impactors were small (less than 10 micrometers) they were heated and dispersed in traversing the entrance foils producing clouds of molten droplets and vapor that produced easily identifiable 'extended impacts' on the Ge target plates. Fortunately, it proved possible to make ion probe measurements of projectile compositions from material deposited on the Ge in the extended impact structures.

Characterization of oil and water accommodated fractions used to conduct aquatic toxicity testing in support of the Deepwater Horizon oil spill natural resource damage assessment.

PubMed

Forth, Heather P; Mitchelmore, Carys L; Morris, Jeffrey M; Lipton, Joshua

2017-06-01

The Deepwater Horizon blowout resulted in the release of millions of barrels of crude oil. As part of the Trustees' Natural Resource Damage Assessment, a testing program was implemented to evaluate the toxicity of Deepwater Horizon oil and oil/dispersant mixtures to aquatic organisms from the Gulf of Mexico. Because of the variety of exposures that likely occurred, the program included 4 Deepwater Horizon oils, which encompassed a range of weathering states, and 3 different oil-in-water mixing methods, for a total of 12 unique water accommodated fractions (WAFs). The present study reports on the chemical characteristics of these 4 Deepwater Horizon oils and 12 WAFs. In addition, to better understand exposure chemistry, an examination was conducted of the effects of WAF preparation parameters-including mixing energy, starting oil composition, and oil-to-water mixing ratios-on the chemical profiles and final concentrations of these 12 WAFs. The results showed that the more weathered the starting oil, the lower the concentrations of the oil constituents in the WAF, with a shift in composition to the less soluble compounds. In addition, higher mixing energies increased the presence of insoluble oil constituents. Finally, at low to mid oil-to-water mixing ratios, the concentration and composition of the WAFs changed with changing mixing ratios; this change was not observed at higher mixing ratios (i.e., >1 g oil/L). Ultimately, the present study provides a basic characterization of the oils and WAFs used in the testing program, which helps to support interpretation of the more than 500 Deepwater Horizon Natural Resource Damage Assessment toxicity testing results and to enable a comparison of these results with different tests and with the field. Environ Toxicol Chem 2017;36:1450-1459. © 2016 SETAC. © 2016 SETAC.

Composite structural materials

NASA Technical Reports Server (NTRS)

Ansell, G. S.; Loewy, R. G.; Wiberley, S. E.

1982-01-01

Research in the basic composition, characteristics, and processng science of composite materials and their constituents is balanced against the mechanics, conceptual design, fabrication, and testing of generic structural elements typical of aerospace vehicles so as to encourage the discovery of unusual solutions to problems. Detailed descriptions of the progress achieved in the various component parts of his program are presented.

The mechanics of delamination in fiber-reinforced composite materials. Part 2: Delamination behavior and fracture mechanics parameters

NASA Technical Reports Server (NTRS)

Wang, S. S.; Choi, I.

1983-01-01

Based on theories of laminate anisotropic elasticity and interlaminar fracture, the complete solution structure associated with a composite delamination is determined. Fracture mechanics parameters characterizing the interlaminar crack behavior are defined from asymptotic stress solutions for delaminations with different crack-tip deformation configurations. A numerical method employing singular finite elements is developed to study delaminations in fiber composites with any arbitrary combinations of lamination, material, geometric, and crack variables. The special finite elements include the exact delamination stress singularity in its formulation. The method is shown to be computationally accurate and efficient, and operationally simple. To illustrate the basic nature of composite delamination, solutions are shown for edge-delaminated (0/-0/-0/0) and (+ or - 0/+ or - 0/90/90 deg) graphite-epoxy systems under uniform axial extenstion. Three-dimensional crack-tip stress intensity factors, associated energy release rates, and delamination crack-closure are determined for each individual case. The basic mechanics and mechanisms of composite delamination are studied, and fundamental characteristics unique to recently proposed tests for interlaminar fracture toughness of fiber composite laminates are examined.

Chondritic Earth: comparisons, guidelines and status

NASA Astrophysics Data System (ADS)

McDonough, W. F.

2014-12-01

The chemical and isotopic composition of the Earth is rationally understood within the context of the chondritic reference frame, without recourse to hidden reservoirs, collision erosion, or strict interpretation of an enstatite chondrite model. Challenges to interpreting the array of recent and disparate chemical and isotopic observations from meteorites need to be understood as rich data harvests that inform us of the compositional heterogeneity in the early solar system. Our ability to resolve small, significant compositional differences between chondrite families provide critical insights into integrated compositional signatures at differing annuli distances from the Sun (i.e., 1-6 AU). Rigorous evaluation of chondritic models for planets requires treatment of both statistical and systematic uncertainties - to date these efforts are uncommonly practiced. Planetary olivine to pyroxene ratio reflects fO2 and temperature potentials in the nebular, given possible ISM compositional conditions; thus this ratio is a non-unique parameter of terrestrial bodies. Consequently the Mg/Si value of a planet (ie., olivine to pyroxene ratio) is a free variable; there is no singular chondritic Mg/Si value. For the Earth, there is an absence of physical and chemical evidence requiring a major element, chemical distinction between the upper and lower mantle, within uncertainties. Early Earth differentiation likely occurred, but there is an absence of chemical and isotopic evidence of its imprint. Chondrites, peridotites, komatiites, and basalts (ancient and modern) reveal a coherent picture of a chondritic compositional Earth, with compositionally affinities to enstatite chondrites. At present results from geoneutrino studies non-uniquely support these conclusions. Future experiments can provide true transformative insights into the Earth's thermal budget, define compositional BSE models, and will restrict discussions on Earth dynamics and its thermal evolution.

On the Impact Origin of Phobos and Deimos. III. Resulting Composition from Different Impactors

NASA Astrophysics Data System (ADS)

Pignatale, Francesco C.; Charnoz, Sébastien; Rosenblatt, Pascal; Hyodo, Ryuki; Nakamura, Tomoki; Genda, Hidenori

2018-02-01

The origin of Phobos and Deimos in a giant impact-generated disk is gaining larger attention. Although this scenario has been the subject of many studies, an evaluation of the chemical composition of the Mars’s moons in this framework is missing. The chemical composition of Phobos and Deimos is unconstrained. The large uncertainties about the origin of the mid-infrared features; the lack of absorption bands in the visible and near-infrared spectra; and the effects of secondary processes on the moons’ surfaces make the determination of their composition very difficult using remote sensing data. Simulations suggest a formation of a disk made of gas and melt with their composition linked to the nature of the impactor and Mars. Using thermodynamic equilibrium, we investigate the composition of dust (condensates from gas) and solids (from a cooling melt) that result from different types of Mars impactors (Mars-, CI-, CV-, EH-, and comet-like). Our calculations show a wide range of possible chemical compositions and noticeable differences between dust and solids, depending on the considered impactors. Assuming that Phobos and Deimos resulted from the accretion and mixing of dust and solids, we find that the derived assemblage (dust-rich in metallic iron, sulfides and/or carbon, and quenched solids rich in silicates) can be compatible with the observations. The JAXA’s Martian Moons eXploration (MMX) mission will investigate the physical and chemical properties of Phobos and Deimos, especially sampling from Phobos, before returning to Earth. Our results could be then used to disentangle the origin and chemical composition of the pristine body that hit Mars and suggest guidelines for helping in the analysis of the returned samples.

Methodology development for quantitative optimization of security enhancement in medical information systems -Case study in a PACS and a multi-institutional radiotherapy database-.

PubMed

Haneda, Kiyofumi; Umeda, Tokuo; Koyama, Tadashi; Harauchi, Hajime; Inamura, Kiyonari

2002-01-01

The target of our study is to establish the methodology for analyzing level of security requirements, for searching suitable security measures and for optimizing security distribution to every portion of medical practice. Quantitative expression must be introduced to our study as possible for the purpose of easy follow up of security procedures and easy evaluation of security outcomes or results. Results of system analysis by fault tree analysis (FTA) clarified that subdivided system elements in detail contribute to much more accurate analysis. Such subdivided composition factors very much depended on behavior of staff, interactive terminal devices, kinds of service, and routes of network. As conclusion, we found the methods to analyze levels of security requirements for each medical information systems employing FTA, basic events for each composition factor and combination of basic events. Methods for searching suitable security measures were found. Namely risk factors for each basic event, number of elements for each composition factor and candidates of security measure elements were found. Method to optimize the security measures for each medical information system was proposed. Namely optimum distribution of risk factors in terms of basic events were figured out, and comparison of them between each medical information systems became possible.

Dietary Effects of Oregano (Origanum Vulgaris L.) Plant or Sweet Chestnut (Castanea Sativa Mill.) Wood Extracts on Microbiological, Chemico-Physical Characteristics and Lipid Oxidation of Cooked ham During Storage.

PubMed

Ranucci, David; Miraglia, Dino; Trabalza-Marinucci, Massimo; Acuti, Gabriele; Codini, Michela; Ceccarini, Maria Rachele; Forte, Claudio; Branciari, Raffaella

2015-11-02

The aim of this study was to evaluate the dietary effect of feeding pigs with diets enriched with sweet chestnut wood ( Castanea sativa Mill.) or oregano ( Origanum vulgaris L.) extract on the microbiological and chemical characteristics of cooked pork ham. Three groups of 10 pigs were fed with a control diet (CTRL), with the CTRL diet enriched with 0.2% of oregano extract (OR) and with the CTRL diet enriched with 0.2% of sweet chestnut wood extract (SCW), respectively. Six cooked hams per group were produced, sliced and packaged under a modified atmosphere (N2:CO2=80:20) and stored at refrigeration temperature (4±1°C). Three packages per cooked ham were sampled for analyses at three different storage times (0, 10 and 20 days). At day 0 time, antioxidant capacity of the products (ORAC FL assay) and chemical composition were performed. At each sampling time, from all the samples the following analyses were performed: total microbial count (TMC), lactic acid bacteria count (LAB), Enterobacteriaceae count, Listeria monocytogenes , pH value, colour coordinates (L*, a*, b*), total basic volatile nitrogen (TBVN) and thiobarbituric reactive substances (TBARs) determinations. No differences in TMC, LAB and Enterobacteriaceae count, pH, TBVN, chemical composition and L* values were registered between the three groups at all the sampling times considered. No Listeria monocytogenes was detected in the samples tested. Significant differences were registered for ORAC FL at 0 days, a* and b* values and TBARs value at 10 and 20 days of storage, with higher values for ORAC FL , a* and b* values and lower values for TBARs in SCW and OR than CTRL. No antimicrobial effect could be recorded for OR and SCW but a higher oxidative stability, also highlighted by the colour maintenance, was observed in both OR and SCW.

Writing Away from Fear: Mina Shaughnessy and the Uses of Authority.

ERIC Educational Resources Information Center

Allen, Michael

1980-01-01

Responds to John Rouse's attack on Mina Shaughnessy's teaching strategies for composition instruction (see EJ 209 264). Offers personal experiences to illustrate the role of the basic writing teacher and the uses of authority in the basic writing classroom. (JT)

Providing Relevance in Chemistry for Nursing Students

ERIC Educational Resources Information Center

Jones, Theodore H. D.

1976-01-01

Describes an introductory chemistry course for nurses in which students learn basic chemical principles by performing 12 chemical analyses that are routinely conducted on body fluids and listed on a patient's clinical laboratory chart. (MLH)

50. VIEW OF CHEMICAL FEED PUMP HOUSE AND NEUTRALIZATION TANK ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

50. VIEW OF CHEMICAL FEED PUMP HOUSE AND NEUTRALIZATION TANK FOR WASTE WATER TREATMENT LOOKING EAST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Band gap and composition engineering on a nanocrystal (BCEN) in solution.

PubMed

Peng, Xiaogang

2010-11-16

Colloidal nanocrystals with "artificial" composition and electron band structure promise to expand the fields of nanomaterials and inorganic chemistry. Despite their promise as functional materials, the fundamental science associated with the synthesis, characterization, and properties of colloidal nanocrystals is still in its infancy and deserves systematic study. Furthermore, such studies are important for our basic understanding of crystallization, surface science, and solid state chemistry. "Band gap and composition engineering on a nanocrystal" (BCEN) refers to the synthesis of a colloidal nanocrystal with composition and/or electron energy band structure that are not found in natural bulk crystals. The BCEN nanostructure shown in the Figure includes a magnetic domain for the separation and recycling of the complex nanostructure, a photoactivated catalytic center, and an additional chemical catalytic center. A thin but porous film (such as a silicate) might be coated onto the nanocrystal, both to provide chemical stability and to isolate the reaction processes from the bulk solution. This example is a catalytic complex analogous to an enzyme that facilitates two sequential reactions in a microenvironment different from bulk solution. The synthesis of colloidal nanocrystals has advanced by a quantum leap in the past two decades. The field now seems ready to extend colloidal nanocrystal synthesis into the BCEN regime. Although BCEN is a very new branch of synthetic chemistry, this Account describes advances in related synthetic and characterization techniques that can serve as a useful starting point for this new area of investigation. To put these ideas into context, this Account compares this new field with organic synthesis, the most developed branch in synthetic chemistry. The structural and functional diversity of organic compounds results from extending design and synthesis beyond the construction of natural organic compounds. If this idea also holds true for inorganic nanocrystals, "artificial" BCEN nanocrystals will most likely outperform the inorganic nanocrystals with naturally occurring structure and composition. If the importance of artificial molecules is a positive lesson from organic synthesis, the practical disadvantage of organic chemistry is that purification can prove much more time consuming than the reaction itself. To get around this problem, colloidal nanocrystal chemists can attempt to avoid these potential purification challenges in the early stages of synthetic method development.

Tracking Radionuclide Fractionation in the First Atomic Explosion Using Stable Elements

DOE PAGES

Bonamici, Chloë E.; Hervig, Richard L.; Kinman, William S.

2017-08-25

Compositional analysis of postdetonation fallout is a tool for forensic identification of nuclear devices. However, the relationship between device composition and fallout composition is difficult to interpret because of the complex combination of physical mixing, nuclear reactions, and chemical fractionations that occur in the chaotic nuclear fireball. By using a combination of in situ microanalytical techniques (electron microprobe analysis and secondary ion mass spectrometry), we show that some heavy stable elements (Rb, Sr, Zr, Ba, Cs, Ba, La, Ce, Nd, Sm, Dy, Lu, U, Th) in glassy fallout from the first nuclear test, Trinity, are reliable chemical proxies for radionuclidesmore » generated during the explosion. Stable-element proxies show that radionuclides from the Trinity device were chemically, but not isotopically, fractionated by condensation. Moreover, stable-element proxies delineate chemical fractionation trends that can be used to connect present-day fallout composition to past fireball composition. Stable-element proxies therefore offer a novel approach for elucidating the phenomenology of the nuclear fireball as it relates to the formation of debris and the fixation of device materials within debris.« less

Tracking Radionuclide Fractionation in the First Atomic Explosion Using Stable Elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonamici, Chloë E.; Hervig, Richard L.; Kinman, William S.

Compositional analysis of postdetonation fallout is a tool for forensic identification of nuclear devices. However, the relationship between device composition and fallout composition is difficult to interpret because of the complex combination of physical mixing, nuclear reactions, and chemical fractionations that occur in the chaotic nuclear fireball. By using a combination of in situ microanalytical techniques (electron microprobe analysis and secondary ion mass spectrometry), we show that some heavy stable elements (Rb, Sr, Zr, Ba, Cs, Ba, La, Ce, Nd, Sm, Dy, Lu, U, Th) in glassy fallout from the first nuclear test, Trinity, are reliable chemical proxies for radionuclidesmore » generated during the explosion. Stable-element proxies show that radionuclides from the Trinity device were chemically, but not isotopically, fractionated by condensation. Moreover, stable-element proxies delineate chemical fractionation trends that can be used to connect present-day fallout composition to past fireball composition. Stable-element proxies therefore offer a novel approach for elucidating the phenomenology of the nuclear fireball as it relates to the formation of debris and the fixation of device materials within debris.« less

Tracking Radionuclide Fractionation in the First Atomic Explosion Using Stable Elements.

PubMed

Bonamici, Chloë E; Hervig, Richard L; Kinman, William S

2017-09-19

Compositional analysis of postdetonation fallout is a tool for forensic identification of nuclear devices. However, the relationship between device composition and fallout composition is difficult to interpret because of the complex combination of physical mixing, nuclear reactions, and chemical fractionations that occur in the chaotic nuclear fireball. Using a combination of in situ microanalytical techniques (electron microprobe analysis and secondary ion mass spectrometry), we show that some heavy stable elements (Rb, Sr, Zr, Ba, Cs, Ba, La, Ce, Nd, Sm, Dy, Lu, U, Th) in glassy fallout from the first nuclear test, Trinity, are reliable chemical proxies for radionuclides generated during the explosion. Stable-element proxies show that radionuclides from the Trinity device were chemically, but not isotopically, fractionated by condensation. Furthermore, stable-element proxies delineate chemical fractionation trends that can be used to connect present-day fallout composition to past fireball composition. Stable-element proxies therefore offer a novel approach for elucidating the phenomenology of the nuclear fireball as it relates to the formation of debris and the fixation of device materials within debris.

Classification of chemical substances, reactions, and interactions: The effect of expertise

NASA Astrophysics Data System (ADS)

Stains, Marilyne Nicole Olivia

2007-12-01

This project explored the strategies that undergraduate and graduate chemistry students engaged in when solving classification tasks involving microscopic (particulate) representations of chemical substances and microscopic and symbolic representations of different chemical reactions. We were specifically interested in characterizing the basic features to which students pay attention while classifying, identifying the patterns of reasoning that they follow, and comparing the performance of students with different levels of preparation in the discipline. In general, our results suggest that advanced levels of expertise in chemical classification do not necessarily evolve in a linear and continuous way with academic training. Novice students had a tendency to reduce the cognitive demand of the task and rely on common-sense reasoning; they had difficulties differentiating concepts (conceptual undifferentiation) and based their classification decisions on only one variable (reduction). These ways of thinking lead them to consider extraneous features, pay more attention to explicit or surface features than implicit features and to overlook important and relevant features. However, unfamiliar levels of representations (microscopic level) seemed to trigger deeper and more meaningful thinking processes. On the other hand, expert students classified entities using a specific set of rules that they applied throughout the classification tasks. They considered a larger variety of implicit features and the unfamiliarity with the microscopic level of representation did not affect their reasoning processes. Consequently, novices created numerous small groups, few of them being chemically meaningful, while experts created few but large chemically meaningful groups. Novices also had difficulties correctly classifying entities in chemically meaningful groups. Finally, expert chemists in our study used classification schemes that are not necessarily traditionally taught in classroom chemistry (e.g. the structure of substances is more relevant to them than their composition when classifying substances as compounds or elements). This result suggests that practice in the field may develop different types of knowledge framework than those usually presented in chemistry textbooks.

The effect of seasons on Brazilian red propolis and its botanical source: chemical composition and antibacterial activity.

PubMed

Bueno-Silva, Bruno; Marsola, Alexandre; Ikegaki, Masaharu; Alencar, Severino M; Rosalen, Pedro L

2017-06-01

The aim of this study was to evaluate the effect of seasons on the chemical composition and antibacterial activity of Brazilian red propolis (BRP) and its plant source. BRP was collected from Maceio, Alagoas state, north-east of Brazil, during one year. Chemical composition was determined by physicochemical analyses and HPLC while antimicrobial activity was assessed against Streptococcus mutans, Streptococcus sobrinus, Staphylococcus aureus and Actinomyces naeslundii by determining the minimal inhibitory and bactericidal concentrations (MIC and MBC, respectively). The comparative chemical profiles varied quantitatively according to the collection period. Formononetin was the most abundant compound in both propolis and resin, while isoliquiritigenin, (3S)-neovestitol, (3S)-vestitol are suggested to be responsible for antimicrobial activity of Brazilian red propolis. MIC varied from 15.6 to 125 μg/mL, whereas MBC varied from 31.2 to 500 μg/mL. Therefore, season in which propolis and its botanical source are collected indeed influences their chemical compositions, resulting in variations in their antibacterial activity.

Assessment of Fecal Near-infrared Spectroscopy to Predict Feces Chemical Composition and Apparent Total Tract Digestibility of Nutrients in Pigs.

PubMed

Nirea, K G; Pérez de Nanclares, M; Skugor, A; Afseth, N K; Meuwissen, T H E; Hansen, J Ø; Mydland, L T; Øverland, M

2018-05-08

Apparent total tract digestibility (ATTD) of nutrients could be an alternative measure of feed efficiency when breeding for robust animals that are fed fiber-rich diets. Apparent total tract digestibility of nutrients requires measuring individual feed intake of a large number of animals which is expensive and complex. Alternatively, ATTD of nutrients and feces chemical composition can be predicted using fecal near-infrared spectroscopy (FNIRS). The objective of this study was to assess if the feces chemical composition and ATTD of nutrients can be predicted using FNIRS that originate from various pig experimental datasets. Fecal samples together with detailed information on the feces chemical composition and ATTD of nutrients were obtained from four different pig experiments. Feces near-infrared spectroscopy were analyzed from fecal samples of a complete dataset. The model was calibrated using the FNIRS and reference samples of feces chemical composition and ATTD of nutrients. The robustness and predictability of the model was evaluated by the r2 and the closeness between SE of calibration (SEC) and SE of cross-validation (SECV). Prediction of the feces chemical components and ATTD of nutrients was successful as SEC and SECV were equivalent. Calibration model was developed to estimate the ATTD of nutrients and fecal chemical composition from the FNIRS and worked well for OM (r2 = 0.94; SEC = 48.5; SECV = 56.6), CP ( r2 = 0.89; SEC = 18.1; SECV = 18.8), GE ( r2 = 0.92; SEC = 1.2; SECV = 1.4), NDF (r2 = 0.94 ; SEC = 55; SECV = 60.2), OM digestibility (r2 = 0.94; SEC = 5.5; SECV = 6.7), GE digestibility (r2 = 0.88; SEC = 2.3; SECV = 2.6) and fat digestibility (r2 = 0.79 ; SEC = 6, SECV = 6.8). However, the SE of prediction was slightly higher than what has been reported in another study. The prediction of feces chemical composition for fat (r2 = 0.69; SEC = 11.7, SECV = 12.3), CP digestibility (r2 = 0.63; SEC = 2.3; SECV = 2.7) and NDF digestibility (r2 = 0.64, SEC = 7.7, SECV = 8.8) was moderate. We conclude that the FNIRS accurately predicts the chemical composition of feces and ATTD of nutrients for OM, CP and GE. The approach of FNIRS is a cost-effective method for measuring digestibility and feed efficiency in a large-scale pig breeding programs.

Generation rates and chemical compositions of waste streams in a typical crewed space habitat

NASA Technical Reports Server (NTRS)

Wydeven, Theodore; Golub, Morton A.

1990-01-01

A judicious compilation of generation rates and chemical compositions of potential waste feed streams in a typical crewed space habitat was made in connection with the waste-management aspect of NASA's Physical/Chemical Closed-Loop Life Support Program. Waste composition definitions are needed for the design of waste-processing technologies involved in closing major life support functions in future long-duration human space missions. Tables of data for the constituents and chemical formulas of the following waste streams are presented and discussed: human urine, feces, hygiene (laundry and shower) water, cleansing agents, trash, humidity condensate, dried sweat, and trace contaminants. Tables of data on dust generation and pH values of the different waste streams are also presented and discussed.

Chemistry of diagenetically altered tuffs at a potential nuclear waste repository, Yucca Mountain, Nye County, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broxton, D.E.; Warren, R.G.; Hagan, R.C.

1986-10-01

The chemistry of diagenetically altered tuffs at a potential nuclear waste repository, Yucca Mountain, Nevada is described. These tuffs contain substantial amounts of zeolites that are highly sorptive of certain radionuclides. Because of their widespread distribution, the zeolitic tuffs could provide important barriers to radionuclide migration. Physical properties of these tuffs and of their constituent zeolites are influenced by their chemical compositions. This study defines the amount of chemical variability within diagenetically altered tuffs and within diagenetic minerals at Yucca Mountain. Zeolitic tuffs at Yucca Mountain formed by diagenetic alteration of rhyolitic vitric tuffs. Despite their similar starting compositions, thesemore » tuffs developed compositions that vary both vertically and laterally. Widespread chemical variations were the result of open-system chemical diagenesis in which chemical components of the tuffs were mobilized and redistributed by groundwaters. Alkalies, alkaline earths, and silica were the most mobile elements during diagenesis. The zeolitic tuffs can be divided into three compositional groups: (1) calcium- and magnesium-rich tuffs associated with relatively thin zones of alteration in the unsaturated zone; (2) tuffs in thick zones of alteration at and below the water table that grade laterally from sodic compositions on the western side of Yucca Mountain to calcic compositions on the eastern side; and (3) potassic tuffs at the north end of Yucca Mountain. Physical properties of tuffs and their consistuent zeolites at Yucca Mountain may be affected by variations in compositions. Properties important for assessment of repository performance include behavior and ion exchange.« less

Health, safety and environmental requirements for composite materials

NASA Technical Reports Server (NTRS)

Hazer, Kathleen A.

1994-01-01

The health, safety and environmental requirements for the production of composite materials are discussed. The areas covered include: (1) chemical identification for each chemical; (2) toxicology; (3) industrial hygiene; (4) fire and safety; (5) environmental aspects; and (6) medical concerns.

Model nebulae and determination of the chemical composition of the Magellanic Clouds

PubMed Central

Aller, L. H.; Keyes, C. D.; Czyzak, S. J.

1979-01-01

An analysis of previously presented photoelectric spectrophotometry of HII regions (emission-line diffuse nebulae) in the two Magellanic Clouds is carried out with the aid of theoretical nebular models, which are used primarily as interpolation devices. Some advantages and limitations of such theoretical models are discussed. A comparison of the finally obtained chemical compositions with those found by other observers shows generally a good agreement, suggesting that it is possible to obtain reliable chemical compositions from low excitation gaseous nebulae in our own galaxy as well as in distant stellar systems. PMID:16592633

Numerical Validation of Chemical Compositional Model for Wettability Alteration Processes

NASA Astrophysics Data System (ADS)

Bekbauov, Bakhbergen; Berdyshev, Abdumauvlen; Baishemirov, Zharasbek; Bau, Domenico

2017-12-01

Chemical compositional simulation of enhanced oil recovery and surfactant enhanced aquifer remediation processes is a complex task that involves solving dozens of equations for all grid blocks representing a reservoir. In the present work, we perform a numerical validation of the newly developed mathematical formulation which satisfies the conservation laws of mass and energy and allows applying a sequential solution approach to solve the governing equations separately and implicitly. Through its application to the numerical experiment using a wettability alteration model and comparisons with existing chemical compositional model's numerical results, the new model has proven to be practical, reliable and stable.

Demonstration of Laser Induced Acoustic Desoprtion - Chemical Ionization Mass Spectrometry (LIAD-CIMS) for Fragment-Free Measurements of Organic Aerosol Molecular Composition

NASA Astrophysics Data System (ADS)

Browne, E. C.; Abdelhamid, A.; Berry, J.; Alton, M.

2017-12-01

Organic compounds account for a significant portion of fine atmospheric aerosol. Current analytical techniques have provided insights on organic aerosol (OA) sources, composition, and chemical modification pathways. Despite this knowledge, large uncertainties remain and hinder our understanding of aerosol impacts on climate, air quality, and health. Measuring OA composition is challenging due to the complex chemical composition and the wide variation in the properties (e.g., vapor pressure, solubility, reactivity) of organic compounds. In many current measurement techniques, the ability to chemically resolve and quantify OA components is complicated by molecular decomposition, matrix effects, and/or preferential ionization mechanisms. Here, we utilize a novel desorption technique, laser induced acoustic desorption (LIAD), that generates fragment-free, neutral gas-phase molecules. We couple LIAD with a high-resolution chemical ionization mass spectrometer (CIMS) to provide molecular composition OA measurements. Through a series of laboratory experiments, we demonstrate the ability of this technique to measure large, thermally labile species without fragmentation/thermal decomposition. We discuss quantification and detection limits of this technique. We compare LIAD-CIMS measurements with thermal desorption-CIMS measurements using off-line measurements of ambient aerosol collected in Boulder, CO. Lastly, we discuss future development for on-line measurements of OA using LIAD-CIMS.

Data from a Thick Unsaturated Zone Underlying Two Artificial Recharge Sites along Oro Grande Wash in the Western Part of the Mojave Desert, near Victorville, San Bernardino County, California, 2001-2006

USGS Publications Warehouse

Clark, Dennis A.; Izbicki, John A.; Johnson, Russell D.; Land, Michael

2009-01-01

This report presents data on the physical and hydraulic properties of unsaturated alluvial deposits and on the chemical and isotopic composition of water collected at two recharge sites in the western part of the Mojave Desert, near Victorville, California, from 2001 to 2006. Unsaturated-zone monitoring sites were installed adjacent to the two recharge ponds using the ODEX air-hammer and air rotary method to depths of about 460 feet and 269 feet below land surface. Each of the two unsaturated-zone monitoring sites included a water-table well, matric-potential sensors, and suction-cup lysimeters installed in a single bore hole. Drilling procedures, lithologic and geophysical data, and site construction and instrumentation are described. Core material was analyzed for water content, bulk density, water potential, particle size, and water retention. The chemical composition of leachate from almost 400 samples of cores and cuttings was determined. Water from suction-cup lysimeters also was analyzed for chemical and isotopic composition. In addition, data on the chemical and isotopic composition of groundwater from the two water-table wells are reported along with chemical and isotopic composition of the surface water in the recharge ponds.

Relationships between botanical and chemical composition of forages: a multivariate approach to grasslands in the Western Italian Alps.

PubMed

Ravetto Enri, Simone; Renna, Manuela; Probo, Massimiliano; Lussiana, Carola; Battaglini, Luca M; Lonati, Michele; Lombardi, Giampiero

2017-03-01

Plant composition of species-rich mountain grasslands can affect the sensorial and chemical attributes of dairy and meat products, with implications for human health. A multivariate approach was used to analyse the complex relationships between vegetation characteristics (botanical composition and plant community variables) and chemical composition (proximate constituents and fatty acid profile) in mesophilic and dry vegetation ecological groups, comprising six different semi-natural grassland types in the Western Italian Alps. Mesophilic and dry grasslands were comparable in terms of phenology, biodiversity indices and proportion of botanical families. The content of total fatty acids and that of the most abundant fatty acids (alpha-linolenic, linoleic and palmitic acids) were mainly associated to nutrient-rich plant species, belonging to the mesophilic grassland ecological group. Mesophilic grasslands showed also higher values of crude protein, lower values of fibre content and they were related to higher pastoral values of vegetation compared to dry grasslands. The proximate composition and fatty acid profile appeared mainly single species dependent rather than botanical family dependent. These findings highlight that forage from mesophilic grasslands can provide higher nutritive value for ruminants and may be associated to ruminant-derived food products with a healthier fatty acid profile. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Amine salts of nitroazoles

DOEpatents

Kienyin Lee; Stinecipher, M.M.

1993-10-26

Compositions of matter, a method of providing chemical energy by burning said compositions, and methods of making said compositions are described. These compositions are amine salts of nitroazoles. 1 figure.

The isotopic composition of authigenic chromium in anoxic marine sediments: A case study from the Cariaco Basin

NASA Astrophysics Data System (ADS)

Reinhard, Christopher T.; Planavsky, Noah J.; Wang, Xiangli; Fischer, Woodward W.; Johnson, Thomas M.; Lyons, Timothy W.

2014-12-01

Chromium (Cr) isotopes are an emerging proxy for tracking redox processes at the Earth's surface. However, there has been limited exploration of the Cr isotope record of modern and recent marine sediments. The basic inorganic chemistry of Cr suggests that anoxic marine basins should factor prominently in the global Cr cycle and that sediments deposited within anoxic basins may offer a valuable Cr isotope archive throughout Earth's history. Here, we present δ53Cr data from sediments of the Cariaco Basin, Venezuela-a 'type' environment for large, perennially anoxic basins with a relatively strong hydrological connection to the global oceans. We document a marked positive shift in bulk δ53Cr values following the termination of the Last Glacial Maximum, followed by relative stasis. Based on a suite of independent redox proxies, this transition marks a switch from oxic to persistently anoxic and sulfidic (euxinic) depositional conditions within the basin. We find good agreement between two independent approaches toward estimating the δ53Cr composition of authigenic Cr in euxinic Cariaco Basin sediments and that these estimates are very similar to the δ53Cr composition of modern open Atlantic Ocean seawater. These data, together with considerations of reaction kinetics and mass balance within the Cariaco Basin, are consistent with the hypothesis that anoxic marine settings can serve as a chemical archive of first-order trends in seawater δ53Cr composition. Additionally, the Cariaco Basin data suggest that there has been secular stability in the average δ53Cr value of Atlantic seawater over the last ∼15 kyr.

Rapid analysis of the chemical composition of agricultural fibers using near infrared spectroscopy and pyrolysis molecular beam mass spectrometry

Treesearch

Stephen S. Kelley; Roger M. Rowell; Mark Davis; Cheryl K. Jurich; Rebecca Ibach

2004-01-01

The chemical composition of a variety of agricultural biomass samples was analyzed with near infrared spectroscopy and pyrolysis molecular beam mass spectroscopy. These samples were selected from a wide array of agricultural residue samples and included residues that had been subjected to a variety of di2erent treatments including solvent extractions and chemical...

Average chemical composition of the lunar surface

NASA Technical Reports Server (NTRS)

Turkevich, A. L.

1973-01-01

The available data on the chemical composition of the lunar surface at eleven sites (3 Surveyor, 5 Apollo and 3 Luna) are used to estimate the amounts of principal chemical elements (those present in more than about 0.5% by atom) in average lunar surface material. The terrae of the moon differ from the maria in having much less iron and titanium and appreciably more aluminum and calcium.

Rapid computation of chemical equilibrium composition - An application to hydrocarbon combustion

NASA Technical Reports Server (NTRS)

Erickson, W. D.; Prabhu, R. K.

1986-01-01

A scheme for rapidly computing the chemical equilibrium composition of hydrocarbon combustion products is derived. A set of ten governing equations is reduced to a single equation that is solved by the Newton iteration method. Computation speeds are approximately 80 times faster than the often used free-energy minimization method. The general approach also has application to many other chemical systems.

Fueling Chemical Engineering Concepts with Biodiesel Production: A Professional Development Experience for High School Pre-Service Teachers

ERIC Educational Resources Information Center

Gupta, Anju

2015-01-01

This one-day workshop for pre-service teachers was aimed at implementing a uniquely designed and ready-to-implement chemical engineering curriculum in high school coursework. This educational and professional development opportunity introduced: 1) chemical engineering curriculum and career opportunities, 2) basic industrial processes and flow…

Recent Progress in Optical Chemical Sensors

PubMed Central

Qazi, Hummad Habib; Mohammad, Abu Bakar bin; Akram, Muhammad

2012-01-01

Optical chemical sensors have promoted escalating interest in the determination of various pollutants in the environment, which are creating toxicity and may cause serious health problems. This review paper focuses particularly on the recent progress and developments in this field; the working principles and basic classes of optical chemical sensors have been briefly described. PMID:23443392

Allied-Signal's Mary Good Analyzes New Threats to Chemical Profession.

ERIC Educational Resources Information Center

Chemical and Engineering News, 1986

1986-01-01

Recounts an interview with chemist, educator, and executive Mary Good. Opinions are expressed about the status of basic research in chemistry, the relationship of chemical research to several federal agencies, the value of education in chemistry, and the perceptions of the public regarding the chemical community, particularly the health risks. (TW)

Chemical Engineering Curricula for the Future: Synopsis of Proceedings of a U.S.-India Conference, January, 1988.

ERIC Educational Resources Information Center

Ramkrishna, D.; And Others

1989-01-01

This is a summary of a seminar for changing the undergraduate chemical engineering curriculum in India. Identifies and describes biotechnology, materials for structural and microelectronic catalysis, and new separation processes as emerging areas. Evaluates the current curriculum, including basic science, engineering lore, chemical engineering,…

Two-Dimensional Photonic Crystals for Sensitive Microscale Chemical and Biochemical Sensing

PubMed Central

Miller, Benjamin L.

2015-01-01

Photonic crystals – optical devices able to respond to changes in the refractive index of a small volume of space – are an emerging class of label-free chemical-and bio-sensors. This review focuses on one class of photonic crystal, in which light is confined to a patterned planar material layer of sub-wavelength thickness. These devices are small (on the order of tens to 100s of microns square), suitable for incorporation into lab-on-a-chip systems, and in theory can provide exceptional sensitivity. We introduce the defining characteristics and basic operation of two-dimensional photonic crystal sensors, describe variations of their basic design geometry, and summarize reported detection results from chemical and biological sensing experiments. PMID:25563402

Physico-chemical transition from peridotite assemblage to the eclogite one (experimental data at 7.0 GPa).

NASA Astrophysics Data System (ADS)

Butvina, Valentina; Litvin, Yurii

2010-05-01

Peridotites and eclogites, including diamond-bearing ones, are the basic ultra-basic and basic rocks of the upper mantle (Ringwood, 1969, 1975; Sobolev, 1974; Marakushev, 1985; Taylor & Anand, 2004). These rocks are presented in the assemblage of mantle xenolyths in kimberlites, but the basic minerals of peridotite paragenesis, olivine, orthopyroxene, garnet and clinopyroxene as well as of an eclogite paragenesis, garnet and omphacite are wide-spread synthetic inclusions in diamonds. The cases of finding minerals and peridotite and eclogite parageneses in diamond are described. It implies that these parageneses can have a single mantle source. However, the formation of peridotite and eclogite mineral parageneses at differentiation of the primary ultrabasite melt during physico-chemical single process is possible only at overcoming the 'eclogite' thermal barrier (O'Hara, 1968; Litvin, 1991). Eclogite genesis is one of the most difficult and discussional problems of modern petrology. Among investigators there is an opinion about eclogite heterogeneity not only on conditions of formation (crust, mantle), but also by composition of the initial rocks (para-, orthoeclogites) as well as by the way of their formation (magmatic, metamorphic, metasomatic). In literature diamond-bearing eclogite nodules of kimberlite pipes are often considered as metamorphic, which are formed at subduction of the Archean or of the Proterozoic oceanic crust (MacGregor & Manton, 1986; McCandless & Gurney, 1986, 1997 et al.). Only the presence of Na2O in garnet and K2O in clinopyroxene is a criterion of their participation in mantle magmatic processes. Together with the hypotheses considered on eclogite origin there exists a version suggested in papers (Kushiro, 1972; Kushiro & Yoder, 1974), according to which mantle eclogites could be formed due to peridotite substance in the processes of fractional crystallization of ultrabasite magmas. The present paper is devoted to the experimental study of this problem. Physico-chemical transition from peridotite assemblage to the eclogite one can be only ensured by the processes of fractional crystallization of mantle magmatic melts. The primary melting and magmatic evolution of mantle garnet lerzolite (or the Ringwood pyrolite) is controlled by a five-phase peritectics 'p' Ol+Opx+Cpx+Grt+L and four cotectic curves conjugated to it (Litvin, 1991). In melting and evolution of melts of both olivine eclogites and coesite and corundum eclogites the corresponding five-phase eutectics are of a dominant importance. A general ridge for all elementary tetrahedrons (simplexes) is a line of compositions diopside-pyrope (clinopyroxene-garnet) which bimineral eclogite assemblages belong to. The internal section En-Di-Cor of the general tetrahendric diagram (symplex complex) separates olivine-saturated and silica-saturated compositions. 'Eclogite' thermal barrier is 'thermal barrier' on (O'Hara, 1968), on the cotectic line Opx+Cpx+Grt+L, connecting 'peridotite' peritectic and 'eclogite' eutectic points. Meanwhile, at equilibrium (and fractional) crystallization of peridotite system in the peritectic point 'p' orthopyroxene vanishes as a result of the peritectic reaction 'orthopyroxene + melt - clinopyroxene' (Davis, 1963; Litvin, 1991). With further temperature decrease the composition of the remnant melt is controlled by the nonorthopyroxene cotectics Ol+Cpx+Grt+L first, in the limits of the peridotite 'simplex', but then mechanism of fractional crystallization is also realized in the limits of the olivine-eclogite 'simplex' up to the corresponding nonvariant eutectics. The considered cotectics Ol+Cpx+Grt+L is of the greatest interest from the viewpoint of a possible change of compositions of remnant melts from olivine-normative to silica-normative ones. One can assume that under the conditions of fractional melt crystallization along the cotectic curve Ol+Cpx+Grt+L together with olivine jigging accumulation of incorehent elements, including Na, Fe etc. takes place. It leads to a gradual increase of jadeite component content in remnant melts what creates grounds for reactional interaction of jadeite and olivine components with olivine vanishing and garnet formation in accordance with the reaction found in (Litvin et al., 2004). A gradual decrease of olivine component content in remnant melts caused by that fact realizes a 'turn' to the cotectic curve Ol+Cpx+Grt+L in the direction of the boundary section En - Di - Cor and, probably its exit to the line Di-Prp (clinopyroxene-garnet). Further under the conditions of fractional crystallization melt composition point can penetrate into the volumes of coesite-eclogite, kyanite-eclogite and corundum-eclogite 'symplexes'. Thus, an overcoming of 'eclogite' thermal barrier between olivine-normative peridotite-pyroxene and SiO2 - normative eclogite compositions occurs. So, one can speak about the 'destruction' of liquidus peridotite-eclogite thermal barrier in the limits of the peridotite 'simplex' as a result of realization of two reaction mechanisms: (1) vanishing of orthopyroxene as a result of its peritectic reaction with the melt with clinopyroxene formation and (2) olivine vanishing as a result of its reactional interaction of jadeite with garnet formation. If with respect to the first mechanism definite experimental evidence exists (Litvin, 1991; Davis, 1963) then for the second mechanism it is absent. Due to this fact the main purpose of this paper is an experimental study of phase relationships in the model system forsterite-dioside-jadeite at pressure of 7 GPa and foundation of possible physico-chemical correct transitions between peridotite and eclogite parageneses with overcoming liquidus 'eclogite' thermal barrier. To construct a diagram of a ternary system forsterite-diopside-jadeite it is necessary to study its boundary binary sections forsterite-jadeite and fosterite-diopside as well as a number of internal polythermic sections. The section jadeite-diopside at 7 GPa has been studied earlier (Bobrov, Litvin, Kojitani, Akaogi, 2006; 2008) and it is characterized by the unlimited miscibility of jadeite and diopside components in solid and liquid states. The first experimental results obtained at the initial stage of the investigation of this problem can be characterized as follows. For the experimental study polythermic sections of forsterite-(jadeite50diopside50) and forsterite-(jadeite25diopside75) have been chosen. The obtained data testify to the fact that olivine vanishing and garnet formation are realized in both sections. The problem of further investigations is to search minimum concentrations of jadeite in the composition of this system where a total olivine vanishing takes place. Thus, the performed experimental investigations of the model system forsterite-diospside-jadeite at pressure 7 GPa testify to the fact that forsterite (olivine) is a stable phase in the boundary system forsterite-diopside (olivine-clinopyroxene). While introducing rather low contents of jadeite component into the composition of this system the reaction of jadeite component with forsterite takes place in the melt. As a result, garnet appears as liquidus phase.

Controls on the chemical composition of saline surface crusts and emitted dust from a wet playa in the Mojave Desert (USA)

USGS Publications Warehouse

Goldstein, Harland L.; Breit, George N.; Reynolds, Richard L.

2017-01-01

Saline-surface crusts and their compositions at ephemeral, dry, and drying lakes are important products of arid-land processes. Detailed understanding is lacking, however, about interactions among locally variable hydrogeologic conditions, compositional control of groundwater on vadose zone and surface salts, and dust composition. Chemical and physical data from groundwater, sediments, and salts reveal compositional controls on saline-surface crusts across a wet playa, Mojave Desert, with bearing on similar settings elsewhere. The compositions of chemically and isotopically distinctive shallow (<3 m) water masses are recorded in the composition of associated salts. In areas with deeper and more saline groundwater, however, not all ions are transported through the vadose zone. Retention of arsenic and other elements in the vadose zone diminishes the concentrations of potentially toxic elements in surface salts, but creates a reservoir of these elements that may be brought to the surface during wetter conditions or by human disturbance. Selective wind-erosion loss of sulfate salts was identified by the compositional contrast between surface salt crusts and underlying groundwater. At the sub-basin scale, compositional links exist among groundwater, salt crusts, and dust from wet playas. Across the study basin, however, lateral variations in groundwater and solid-salt compositions are produced by hydrogeologic heterogeneity.

Improvement of efficiency in graphene/gallium nitride nanowire on Silicon photoelectrode for overall water splitting

NASA Astrophysics Data System (ADS)

Bae, Hyojung; Rho, Hokyun; Min, Jung-Wook; Lee, Yong-Tak; Lee, Sang Hyun; Fujii, Katsushi; Lee, Hyo-Jong; Ha, Jun-Seok

2017-11-01

Gallium nitride (GaN) nanowires are one of the most promising photoelectrode materials due to their high stability in acidic and basic electrolytes, and tunable band edge potentials. In this study, GaN nanowire arrays (GaN NWs) were prepared by molecular beam epitaxy (MBE); their large surface area enhanced the solar to hydrogen conversion efficiency. More significantly, graphene was grown by chemical vapor deposition (CVD), which enhanced the electron transfer between NWs for water splitting and protected the GaN NW surface. Structural characterizations of the prepared composite were performed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The photocurrent density of Gr/GaN NWs exhibited a two-fold increase over pristine GaN NWs and sustained water splitting up to 70 min. These improvements may accelerate possible applications for hydrogen generation with high solar to hydrogen conversion efficiency.

The OpenCalphad thermodynamic software interface.

PubMed

Sundman, Bo; Kattner, Ursula R; Sigli, Christophe; Stratmann, Matthias; Le Tellier, Romain; Palumbo, Mauro; Fries, Suzana G

2016-12-01

Thermodynamic data are needed for all kinds of simulations of materials processes. Thermodynamics determines the set of stable phases and also provides chemical potentials, compositions and driving forces for nucleation of new phases and phase transformations. Software to simulate materials properties needs accurate and consistent thermodynamic data to predict metastable states that occur during phase transformations. Due to long calculation times thermodynamic data are frequently pre-calculated into "lookup tables" to speed up calculations. This creates additional uncertainties as data must be interpolated or extrapolated and conditions may differ from those assumed for creating the lookup table. Speed and accuracy requires that thermodynamic software is fully parallelized and the Open-Calphad (OC) software is the first thermodynamic software supporting this feature. This paper gives a brief introduction to computational thermodynamics and introduces the basic features of the OC software and presents four different application examples to demonstrate its versatility.

The OpenCalphad thermodynamic software interface

PubMed Central

Sundman, Bo; Kattner, Ursula R; Sigli, Christophe; Stratmann, Matthias; Le Tellier, Romain; Palumbo, Mauro; Fries, Suzana G

2017-01-01

Thermodynamic data are needed for all kinds of simulations of materials processes. Thermodynamics determines the set of stable phases and also provides chemical potentials, compositions and driving forces for nucleation of new phases and phase transformations. Software to simulate materials properties needs accurate and consistent thermodynamic data to predict metastable states that occur during phase transformations. Due to long calculation times thermodynamic data are frequently pre-calculated into “lookup tables” to speed up calculations. This creates additional uncertainties as data must be interpolated or extrapolated and conditions may differ from those assumed for creating the lookup table. Speed and accuracy requires that thermodynamic software is fully parallelized and the Open-Calphad (OC) software is the first thermodynamic software supporting this feature. This paper gives a brief introduction to computational thermodynamics and introduces the basic features of the OC software and presents four different application examples to demonstrate its versatility. PMID:28260838

Coal Combustion Science quarterly progress report, April--June 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardesty, D.R.; Hurt, R.H.; Baxter, L.L.

1992-09-01

The objective of this work is to support the Office of Fossil Energy in executing research on coal combustion science. This project consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center (PETC) Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency (IEA) Coal Combustion Science Project. Specific tasks include: The characterization of the physical and chemical processes that constitute the early devolatilization phase of coal combustion: Characterization of the combustion behavior of selected coals under conditions relevant to industria pulverized coal-fired furnaces; and to establish a quantitative understanding of themore » mechanisms and rates of transformation, fragmentation, and deposition of mineral matter in coal combustion environments as a function of coal type, particle size and temperature, the initial forms and distributions of mineral species in the unreacted coal, and the local gas temperature and composition.« less

NanoParticle Ontology for Cancer Nanotechnology Research

PubMed Central

Thomas, Dennis G.; Pappu, Rohit V.; Baker, Nathan A.

2010-01-01

Data generated from cancer nanotechnology research are so diverse and large in volume that it is difficult to share and efficiently use them without informatics tools. In particular, ontologies that provide a unifying knowledge framework for annotating the data are required to facilitate the semantic integration, knowledge-based searching, unambiguous interpretation, mining and inferencing of the data using informatics methods. In this paper, we discuss the design and development of NanoParticle Ontology (NPO), which is developed within the framework of the Basic Formal Ontology (BFO), and implemented in the Ontology Web Language (OWL) using well-defined ontology design principles. The NPO was developed to represent knowledge underlying the preparation, chemical composition, and characterization of nanomaterials involved in cancer research. Public releases of the NPO are available through BioPortal website, maintained by the National Center for Biomedical Ontology. Mechanisms for editorial and governance processes are being developed for the maintenance, review, and growth of the NPO. PMID:20211274

Directional synthesis of ethylbenzene through catalytic transformation of lignin.

PubMed

Fan, Minghui; Jiang, Peiwen; Bi, Peiyan; Deng, Shumei; Yan, Lifeng; Zhai, Qi; Wang, Tiejun; Li, Quanxin

2013-09-01

Transformation of lignin to ethylbenzene can provide an important bulk raw material for the petrochemical industry. This work explored the production of ethylbenzene from lignin through the directional catalytic depolymerization of lignin into the aromatic monomers followed by the selective alkylation of the aromatic monomers. For the first step, the aromatics selectivity of benzene derived from the catalytic depolymerization of lignin reached about 90.2 C-mol% over the composite catalyst of Re-Y/HZSM-5 (25). For the alkylation of the aromatic monomers in the second step, the highest selectivity of ethylbenzene was about 72.3 C-mol% over the HZSM-5 (25) catalyst. The reaction pathway for the transformation of lignin to ethylbenzene was also addressed. Present transformation potentially provides a useful approach for the production of the basic petrochemical material and development of high-end chemicals utilizing lignin as the abundant natural aromatic resource. Copyright © 2013 Elsevier Ltd. All rights reserved.

Immobilizing Highly Catalytically Active Pt Nanoparticles inside the Pores of Metal-Organic Framework: A Double Solvents Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aijaz, Arshad; Karkamkar, Abhijeet J.; Choi, Young Joon

2012-08-29

Ultrafine Pt nanoparticles were successfully immobilized inside the pores of a metal-organic framework MIL-101 without deposition of Pt nanoparticles on the external surfaces of framework by using a 'double solvents' method. The resulting Pt@MIL-101 composites with different Pt loadings represent the first highly active MOF-immobilized metal nanocatalysts for catalytic reactions in all three phases: liquid-phase ammonia borane hydrolysis; solid-phase ammonia borane thermal dehy-drogenation and gas-phase CO oxidation. The observed excellent catalytic performances are at-tributed to the small Pt nanoparticles within the pores of MIL-101. 'We are thankful to AIST and METI for financial support. TA & AK are thankful formore » support from the US Department of Energy, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. PNNL is operated by Battelle.'« less

Composite Material from By-products and Its Properties

NASA Astrophysics Data System (ADS)

Šeps, K.; Broukalová, I.; Vodička, J.

2017-09-01

The paper shows an example of utilization of specific textile admixture - fluffs of torn textiles from waste cars in production of composite with aggregate consisting entirely of unsorted recycled concrete. The admixture in the mixture of recycled concrete and cement binder fills the pores and voids in composite. The elaborated composite has working title STEREDconcrete. In the article, basic mechanical-physical properties of the composite are presented also the fire resistance of STEREDconcrete, which was determined in tests.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tahir, Dahlang, E-mail: dtahir@fmipa.unhas.ac.id; Bakri, Fahrul; Liong, Syarifuddin

We have studied the molecular properties, structural properties, and chemical composition of composites by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) spectroscopy, and X-ray fluorescence (XRF) spectroscopy, respectively. FTIR spectra shows absorption band of hydroxyl group (-OH), methyl group (-CH{sub 3}) and aromatic group (C-C). The absorption band for aromatic group (C-C) shows the formation of carbonaceous in composites. XRF shows chemical composition of composites, which the main chemicals are SO{sub 3}, Cl, and ZnO. The loss on ignition value (LOI) of activated charcoal indicates high carbonaceous matter. The crystallite size for diffraction pattern from hydrogel polymer is aboutmore » 17 nm and for activated charcoal are about 19 nm. The crystallite size of the polymer is lower than that of activated charcoal, which make possible of the particle from filler in contact with each other to form continuous conducting polymer through polymer matrix.« less

Chemical Composition of Different Botanical Origin Honeys Produced by Sicilian Black Honeybees (Apis mellifera ssp. sicula).

PubMed

Mannina, Luisa; Sobolev, Anatoly P; Di Lorenzo, Arianna; Vista, Silvia; Tenore, Gian Carlo; Daglia, Maria

2015-07-01

In 2008 a Slow Food Presidium was launched in Sicily (Italy) for an early warning of the risk of extinction of the Sicilian native breed of black honeybee (Apis mellifera L. ssp sicula). Today, the honey produced by these honeybees is the only Sicilian honey produced entirely by the black honeybees. In view of few available data regarding the chemical composition of A. mellifera ssp. sicula honeys, in the present investigation the chemical compositions of sulla honey (Hedysarum coronarium L.) and dill honey (Anethum graveolens L.) were studied with a multimethodological approach, which consists of HPLC-PDA-ESI-MSn and NMR spectroscopy. Moreover, three unifloral honeys (lemon honey (obtained from Citrus limon (L.) Osbeck), orange honey (Citrus arantium L.), and medlar honey (Eriobotrya japonica (Thunb.) Lindl)), with known phenol and polyphenol compositions, were studied with NMR spectroscopy to deepen the knowledge about sugar and amino acid compositions.

Compositional descriptor-based recommender system for the materials discovery

NASA Astrophysics Data System (ADS)

Seko, Atsuto; Hayashi, Hiroyuki; Tanaka, Isao

2018-06-01

Structures and properties of many inorganic compounds have been collected historically. However, it only covers a very small portion of possible inorganic crystals, which implies the presence of numerous currently unknown compounds. A powerful machine-learning strategy is mandatory to discover new inorganic compounds from all chemical combinations. Herein we propose a descriptor-based recommender-system approach to estimate the relevance of chemical compositions where crystals can be formed [i.e., chemically relevant compositions (CRCs)]. In addition to data-driven compositional similarity used in the literature, the use of compositional descriptors as a prior knowledge is helpful for the discovery of new compounds. We validate our recommender systems in two ways. First, one database is used to construct a model, while another is used for the validation. Second, we estimate the phase stability for compounds at expected CRCs using density functional theory calculations.

The Impact of Marine Enzymatic Activity on Sea Spray Aerosol Properties

NASA Astrophysics Data System (ADS)

Ryder, O. S.; Michaud, J. M.; Sauer, J. S.; Lee, C.; Förster, J. D.; Pöhlker, C.; Andreae, M. O.; Prather, K. A.

2016-12-01

The composition of sea spray aerosol (SSA) and the relationship between its organic fraction and biological ocean conditions is not well understood, resulting in considerable disagreement in the literature linking biological markers to SSA chemical composition. Recent work suggests that enzymatic activity in seawater may play a key role in dictating aerosol composition by changing the organic pool from which SSA is formed. Here we investigate the role of enzymatic activity on SSA spatial chemical composition, aerosol phase and morphological microstructure. In these experiments, SSA was generated using a novel mini-Marine Aerosol Reference Tank system. SSA collected onto substrates was generated from artificial salt water that had been doped with either 1) unsaturated triglycerides or 2) diatom cellular lysate, both followed by lipase. Results from analysis including morphological studies via atomic force microscopy, and chemical composition investigations both under dry and RH conditions via STXM-NEXAFS are presented.

Multi-component quantitation of meso/nanostructural surfaces and its application to local chemical compositions of copper meso/nanostructures self-organized on silica

NASA Astrophysics Data System (ADS)

Huang, Chun-Yi; Chang, Hsin-Wei; Chang, Che-Chen

2018-03-01

Knowledge about the chemical compositions of meso/nanomaterials is fundamental to development of their applications in advanced technologies. Auger electron spectroscopy (AES) is an effective analysis method for the characterization of meso/nanomaterial structures. Although a few studies have reported the use of AES for the analysis of the local composition of these structures, none have explored in detail the validity of the meso/nanoanalysis results generated by the AES instrument. This paper addresses the limitations of AES and the corrections necessary to offset them for this otherwise powerful meso/nanoanalysis tool. The results of corrections made to the AES multi-point analysis of high-density copper-based meso/nanostructures provides major insights into their local chemical compositions and technological prospects, which the primitive composition output of the AES instrument failed to provide.

Chemical and isotopic database of water and gas from hydrothermal systems with an emphasis for the western United States

USGS Publications Warehouse

Mariner, R.H.; Venezky, D.Y.; Hurwitz, S.

2006-01-01

Chemical and isotope data accumulated by two USGS Projects (led by I. Barnes and R. Mariner) over a time period of about 40 years can now be found using a basic web search or through an image search (left). The data are primarily chemical and isotopic analyses of waters (thermal, mineral, or fresh) and associated gas (free and/or dissolved) collected from hot springs, mineral springs, cold springs, geothermal wells, fumaroles, and gas seeps. Additional information is available about the collection methods and analysis procedures.The chemical and isotope data are stored in a MySQL database and accessed using PHP from a basic search form below. Data can also be accessed using an Open Source GIS called WorldKit by clicking on the image to the left. Additional information is available about WorldKit including the files used to set up the site.

Composition and conductance distributions of single GeSi quantum rings studied by conductive atomic force microscopy combined with selective chemical etching.

PubMed

Lv, Y; Cui, J; Jiang, Z M; Yang, X J

2013-02-15

Atomic force microscopy imaging combined with selective chemical etching is employed to quantitatively investigate three-dimensional (3D) composition distributions of single GeSi quantum rings (QRs). In addition, the 3D quantitative composition distributions and the corresponding conductance distributions are simultaneously obtained on the same single GeSi QRs by conductive atomic force microscopy combined with selective chemical etching, allowing us to investigate the correlations between the conductance and composition distributions of single QRs. The results show that the QRs' central holes have higher Ge content, but exhibit lower conductance, indicating that the QRs' conductance distribution is not consistent with their composition distribution. By comparing the topography, composition and conductance profiles of the same single QRs before and after different etching processes, it is found that the conductance distributions of GeSi QRs do not vary with the change of composition distribution. Instead, the QRs' conductance distributions are found to be consistent with their topographic shapes, which can be supposed to be due to the shape determined electronic structures.

Uranium as a possible criterion for the hydro-chemical alteration of betafite

NASA Astrophysics Data System (ADS)

Hosseinpour Khanmiri, Mohammad; Yanson, Svetlana Yu.; Fomin, Edward V.; Titov, Anatoly V.; Grebeniuk, Andrey V.; Polekhovsky, Yury S.; Bogdanov, Roman V.

2018-01-01

Hydro-chemical processes significantly alter the original composition of metamict minerals. In the work presented here, an attempt was made to reconstruct the chemical composition of betafite in the earlier stages of its geological history. The time scale is determined by the leaching rate of the isotope 238U, a process that takes its course in line with first-order kinetics, or something close to it. The leaching rate constant of this uranium isotope was assessed. Based on available data in the literature, the hydro-chemical behavior of various atoms in group A of betafite was analyzed. The chemical composition of the mineral was calculated taking into account the total charge of the cations that the betafite had at the time it was formed, or possibly the last time it was completely reformed as a result of diverse endogenic processes.

Uranium as a possible criterion for the hydro-chemical alteration of betafite

NASA Astrophysics Data System (ADS)

Hosseinpour Khanmiri, Mohammad; Yanson, Svetlana Yu.; Fomin, Edward V.; Titov, Anatoly V.; Grebeniuk, Andrey V.; Polekhovsky, Yury S.; Bogdanov, Roman V.

2018-06-01

Hydro-chemical processes significantly alter the original composition of metamict minerals. In the work presented here, an attempt was made to reconstruct the chemical composition of betafite in the earlier stages of its geological history. The time scale is determined by the leaching rate of the isotope 238U, a process that takes its course in line with first-order kinetics, or something close to it. The leaching rate constant of this uranium isotope was assessed. Based on available data in the literature, the hydro-chemical behavior of various atoms in group A of betafite was analyzed. The chemical composition of the mineral was calculated taking into account the total charge of the cations that the betafite had at the time it was formed, or possibly the last time it was completely reformed as a result of diverse endogenic processes.

Chemistry and Composition of Atmospheric Aerosol Particles

NASA Astrophysics Data System (ADS)

Kolb, Charles E.; Worsnop, Douglas R.

2012-05-01

For more than two decades a cadre of physical chemists has focused on understanding the formation processes, chemical composition, and chemical kinetics of atmospheric aerosol particles and droplets with diameters ranging from a few nanometers to ˜10,000 nm. They have adapted or invented a range of fundamental experimental and theoretical tools to investigate the thermochemistry, mass transport, and chemical kinetics of processes occurring at nanoscale gas-liquid and gas-solid interfaces for a wide range of nonideal, real-world substances. State-of-the-art laboratory methods devised to study molecular spectroscopy, chemical kinetics, and molecular dynamics also have been incorporated into field measurement instruments that are deployed routinely on research aircraft, ships, and mobile laboratories as well as at field sites from megacities to the most remote jungle, desert, and polar locations. These instruments can now provide real-time, size-resolved aerosol particle physical property and chemical composition data anywhere in Earth's troposphere and lower stratosphere.

Investigations of plastic composite materials for highway safety structures

DOT National Transportation Integrated Search

1998-08-01

This report presents a basic overview and assessment of different concepts and technologies of using polymer composites in structures generally used for highway safety. The structural systems included a highway barrier guardrail with its posts and bl...

T1ρ magnetic resonance: basic physics principles and applications in knee and intervertebral disc imaging.

PubMed

Wáng, Yì-Xiáng J; Zhang, Qinwei; Li, Xiaojuan; Chen, Weitian; Ahuja, Anil; Yuan, Jing

2015-12-01

T1ρ relaxation time provides a new contrast mechanism that differs from T1- and T2-weighted contrast, and is useful to study low-frequency motional processes and chemical exchange in biological tissues. T1ρ imaging can be performed in the forms of T1ρ-weighted image, T1ρ mapping and T1ρ dispersion. T1ρ imaging, particularly at low spin-lock frequency, is sensitive to B0 and B1 inhomogeneity. Various composite spin-lock pulses have been proposed to alleviate the influence of field inhomogeneity so as to reduce the banding-like spin-lock artifacts. T1ρ imaging could be specific absorption rate (SAR) intensive and time consuming. Efforts to address these issues and speed-up data acquisition are being explored to facilitate wider clinical applications. This paper reviews the T1ρ imaging's basic physic principles, as well as its application for cartilage imaging and intervertebral disc imaging. Compared to more established T2 relaxation time, it has been shown that T1ρ provides more sensitive detection of proteoglycan (PG) loss at early stages of cartilage degeneration. T1ρ has also been shown to provide more sensitive evaluation of annulus fibrosis (AF) degeneration of the discs.

T1ρ magnetic resonance: basic physics principles and applications in knee and intervertebral disc imaging

PubMed Central

Zhang, Qinwei; Li, Xiaojuan; Chen, Weitian; Ahuja, Anil; Yuan, Jing

2015-01-01

T1ρ relaxation time provides a new contrast mechanism that differs from T1- and T2-weighted contrast, and is useful to study low-frequency motional processes and chemical exchange in biological tissues. T1ρ imaging can be performed in the forms of T1ρ-weighted image, T1ρ mapping and T1ρ dispersion. T1ρ imaging, particularly at low spin-lock frequency, is sensitive to B0 and B1 inhomogeneity. Various composite spin-lock pulses have been proposed to alleviate the influence of field inhomogeneity so as to reduce the banding-like spin-lock artifacts. T1ρ imaging could be specific absorption rate (SAR) intensive and time consuming. Efforts to address these issues and speed-up data acquisition are being explored to facilitate wider clinical applications. This paper reviews the T1ρ imaging’s basic physic principles, as well as its application for cartilage imaging and intervertebral disc imaging. Compared to more established T2 relaxation time, it has been shown that T1ρ provides more sensitive detection of proteoglycan (PG) loss at early stages of cartilage degeneration. T1ρ has also been shown to provide more sensitive evaluation of annulus fibrosis (AF) degeneration of the discs. PMID:26807369

Species diversity and chemical properties of litter influence non-additive effects of litter mixtures on soil carbon and nitrogen cycling

PubMed Central

Mao, Bing; Mao, Rong; Zeng, De-Hui

2017-01-01

Decomposition of litter mixtures generally cannot be predicted from the component species incubated in isolation. Therefore, such non-additive effects of litter mixing on soil C and N dynamics remain poorly understood in terrestrial ecosystems. In this study, litters of Mongolian pine and three dominant understory species and soil were collected from a Mongolian pine plantation in Northeast China. In order to examine the effects of mixed-species litter on soil microbial biomass N, soil net N mineralization and soil respiration, four single litter species and their mixtures consisting of all possible 2-, 3- and 4-species combinations were added to soils, respectively. In most instances, species mixing produced synergistic non-additive effects on soil microbial biomass N and soil respiration, but antagonistic non-additive effects on net N mineralization. Species composition rather than species richness explained the non-additive effects of species mixing on soil microbial biomass N and net N mineralization, due to the interspecific differences in litter chemical composition. Both litter species composition and richness explained non-additive soil respiration responses to mixed-species litter, while litter chemical diversity and chemical composition did not. Our study indicated that litter mixtures promoted soil microbial biomass N and soil respiration, and inhibited net N mineralization. Soil N related processes rather than soil respiration were partly explained by litter chemical composition and chemical diversity, highlighting the importance of functional diversity of litter on soil N cycling. PMID:28686660

Species diversity and chemical properties of litter influence non-additive effects of litter mixtures on soil carbon and nitrogen cycling.

PubMed

Mao, Bing; Mao, Rong; Zeng, De-Hui

2017-01-01

Decomposition of litter mixtures generally cannot be predicted from the component species incubated in isolation. Therefore, such non-additive effects of litter mixing on soil C and N dynamics remain poorly understood in terrestrial ecosystems. In this study, litters of Mongolian pine and three dominant understory species and soil were collected from a Mongolian pine plantation in Northeast China. In order to examine the effects of mixed-species litter on soil microbial biomass N, soil net N mineralization and soil respiration, four single litter species and their mixtures consisting of all possible 2-, 3- and 4-species combinations were added to soils, respectively. In most instances, species mixing produced synergistic non-additive effects on soil microbial biomass N and soil respiration, but antagonistic non-additive effects on net N mineralization. Species composition rather than species richness explained the non-additive effects of species mixing on soil microbial biomass N and net N mineralization, due to the interspecific differences in litter chemical composition. Both litter species composition and richness explained non-additive soil respiration responses to mixed-species litter, while litter chemical diversity and chemical composition did not. Our study indicated that litter mixtures promoted soil microbial biomass N and soil respiration, and inhibited net N mineralization. Soil N related processes rather than soil respiration were partly explained by litter chemical composition and chemical diversity, highlighting the importance of functional diversity of litter on soil N cycling.

Computer-aided design of polymers and composites

NASA Technical Reports Server (NTRS)

Kaelble, D. H.

1985-01-01

This book on computer-aided design of polymers and composites introduces and discusses the subject from the viewpoint of atomic and molecular models. Thus, the origins of stiffness, strength, extensibility, and fracture toughness in composite materials can be analyzed directly in terms of chemical composition and molecular structure. Aspects of polymer composite reliability are considered along with characterization techniques for composite reliability, relations between atomic and molecular properties, computer aided design and manufacture, polymer CAD/CAM models, and composite CAD/CAM models. Attention is given to multiphase structural adhesives, fibrous composite reliability, metal joint reliability, polymer physical states and transitions, chemical quality assurance, processability testing, cure monitoring and management, nondestructive evaluation (NDE), surface NDE, elementary properties, ionic-covalent bonding, molecular analysis, acid-base interactions, the manufacturing science, and peel mechanics.

Structure and chemical composition of the dentin-enamel junction analyzed by Confocal Raman Microscopy

NASA Astrophysics Data System (ADS)

Desoutter, A.; Salehi, H.; Slimani, A.; Marquet, P.; Jacquot, B.; Tassery, H.; Cuisinier, F. J. G.

2014-02-01

The structure and chemical composition of the human dentin-enamel junction (DEJ) was studied using confocal Raman microscopy - a chemical imaging technique. Slices of non-fixed, sound teeth were prepared with an Isomet diamond saw and scanned with Witec Alpha300R system. The combination of different characteristics peaks of phosphate, carbonate and organic matrix (respectively 960, 1072 and 1545 cm-1), generates images representing the chemical composition of the DEJ area. Images are also calculated using peak ratios enabling precise determination of the chemical composition across the DEJ. Then, with two characterized peaks, different pictures are calculated to show the ratio of two components. The images of the spatial distribution of mineral phosphate (960cm-1) to organic matrix (1545 cm-1) ratios, mineral carbonates (1072cm-1) to mineral phosphate ratios; and mineral carbonates to organic matrix ratios were reconstructed. Cross sectional and calculated graphic profile show the variations of the different chemical component ratios through the enamel and the dentin. Phosphate to organic ratio shows an accumulation of organic material under the enamel surface. The cross sectional profile of these pictures shows a high phosphate content compared to enamel in the vicinity of the DEJ. The Confocal Raman imaging technique can be used to further provide full chemical imaging of tooth, particularly of the whole DEJ and to study enamel and dentin decay.

Basic mechanics of laminated composite plates

NASA Technical Reports Server (NTRS)

Nettles, Alan T.

1994-01-01

The mechanics of laminated composite materials is presented in a clear manner with only essential derivations included. The constitutive equations in all of their forms are developed and then summarized in a separate section. The effects of hygrothermal effects are included. The prediction of the engineering constants for a laminate are derived. Strength of laminated composites is not covered.