Science.gov

Sample records for basin-brazil controle estrutural

  1. Factors controlling the abundance of organic sulfur in flash pyrolyzates of Upper Cretaceous kerogens from Sergipe Basin, Brazil

    USGS Publications Warehouse

    Carmo, A.M.; Stankiewicz, B.A.; Mastalerz, Maria; Pratt, L.M.

    1997-01-01

    The molecular and elemental composition of immature kerogens isolated from Upper Cretaceous marine carbonates from Sergipe Basin, Brazil were investigated using combined pyrolysis-gas chromatography/mass spectrometry and organic petrographic techniques. The kerogens are predominantly composed of reddish-fluorescing amorphous organic matter (AOM) and variable amounts of yellow-fluorescing alginite and liptodetrinite. The abundance of organic sulfur in the kerogens inferred from the ratio 2-ethyl-5-methylthiophene/(1,2-dimethylbenzene + dec-1-ene) in the pyrolyzates is variable and may be related to changes in the type of primary organic input and/or to variations in rates of bacterial sulfate reduction. A concomitant increase in S/C and O/C ratios determined in situ using the electron microprobe is observed in AOM and alginites and may be related to a progressive oxidation of the organic matter during sulfurization. The S/C ratio of the AOM is systematically higher than the S C ratio of the alginites. Combined with a thiophene distribution characteristic of pyrolyzates of Type II organic matter, the higher S/C of AOM in Sergipe kerogens suggests that sulfurization and incorporation of low-molecular weight lipids derived from normal marine organic matter into the kerogen structure predominated over direct sulfurization of highly aliphatic algal biomacromolecules.The molecular and elemental composition of immature kerogens isolated from Upper Cretaceous marine carbonates from Sergipe Basin, Brazil were investigated using combined pyrolysis-gas chromatography/mass spectrometry and organic petrographic techniques. The kerogens are predominantly composed of reddish-fluorescing amorphous organic matter (AOM) and variable amounts of yellow-fluorescing alginite and liptodetrinite. The abundance of organic sulfur in the kerogens inferred from the ratio 2-ethyl-5-methylthiophene/(1,2-dimethylbenzene+dec-1-ene) in the pyrolyzates is variable and may be related to changes in

  2. Anatomy and controlling factors of a Late Cretaceous Aeolian sand sheet: The Marília and the Adamantina formations, NW Bauru Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Basilici, Giorgio; Führ Dal'Bó, Patrick Francisco

    2010-04-01

    Few previous studies have given significant consideration to the palaeosols in aeolian sand sheet sedimentary successions and, mainly, to their palaeoenvironmental and stratigraphic meaning in interaction with the deposits. These themes are considered in this study that deals with the depositional architecture and the factors controlling the construction, accumulation and preservation of an ancient aeolian sand sheet, that forms part of the Adamantina and Marília formations, in the Bauru Basin (Late Cretaceous, Brazil). In the NW portion of the Bauru Basin, these two units, ca 220 m thick, consist of sandstone, and secondarily of sandy conglomerate and mudstone, and are characterised by vertically alternated palaeosols and deposits. Facies analyses of the deposits and macroscopic characterisation of the palaeosols in 45 outcrops were integrated with laboratory analyses that consisted in descriptions of slabs of rock samples, petrographic analyses, clay mineralogy determination, geochemical analyses of the major oxides, and micromorphological characterisation of the palaeosols. Three architectural elements were recognised: palaeosols, wind-ripple-dominated aeolian sand sheet deposits, and ephemeral river deposits. The palaeosols constitute 66% of the entire sedimentary succession, and consist principally of Aridisols and, subordinately, of Alfisols, Vertisols, and Entisols. The wind-ripple-dominated aeolian sand sheet deposits (25%) are composed of sandstone, organised in translatent climbing wind-ripple strata, and secondarily of sandstone and mudstone deposited by infrequent floods. The ephemeral river deposits (9%) consist of sandy conglomerates 4 m thick and ca 2 km wide. Wind-ripple-dominated aeolian sand sheet deposits formed during relatively dry climate period on an unstable topographic surface of an aeolian sand sheet, where aeolian deposition or erosion prevailed. Palaeosols and ephemeral river deposits formed in a more humid climate period on a stable

  3. Early Cretaceous coniferous woods from a paleoerg (Paraná Basin, Brazil)

    NASA Astrophysics Data System (ADS)

    Pires, Etiene Fabbrin; Guerra-Sommer, Margot; Scherer, Claiton Marlon dos Santos; Santos, Adriano Rodrigues dos; Cardoso, Edivane

    2011-07-01

    We report here the occurrence of an assemblage of silicified coniferous wood within aeolian sandstones of the Early Cretaceous Botucatu Formation, a paleoerg along the margins of the Paraná Basin (Brazil). The characteristics of this monotypic wood assemblage indicate the occurrence of some more humid periods during the prevailing arid climate of a semi-desert biome. The growing conditions were seasonal and stressed during the life cycle of the trees. Quantitative parameters controlling growth ring development might be closely related to local environmental conditions and not just only a single consequence of climate. The conifer assemblage, developed in an arid desert biome during the climax of a greenhouse phase with increasing atmospheric CO 2 does not have modern analogues in present icehouse world.

  4. Petroleum migration and mixing in the Potiguar basin, Brazil

    SciTech Connect

    Trindade, L.A.F.; Santos Neto, E.V. ); Brassell, S.C. )

    1992-12-01

    Regional studies of petroleum samples from both offshore and onshore reservoirs of the Potiguar basin, Brazil, reveal compositional differences, with discernible landward trends, attributable to oil mixing. These chemical discrepancies can be related to a combination of source rocks, maturity, and migration history. The source rocks are classified in two groups based on their geochemical and molecular characteristics: (1) Neocomian and Aptian lacustrine freshwater shales, and (2) Aptian marine evaporitic shales and marls. Both lie in an offshore structural low. The geochemically contrasting oils derived from these source beds migrated updip, constrained by a monoclinal structure, through Aptian carrier beds to thermally immature strata. Evaluation of compositional heterogeneities in the oils and an investigation of migration effects on their compositions reveal trends related to the amount of mixing which, in turn, reflects the timing of both oil generation and migration, and the direction of migration. The more migrated oils contain greater contributions from freshwater sources, whereas the less migrated oils display more pronounced contributions from the younger and shallower hypersaline source beds. Biomarker maturity parameters indicate that the most migrated oils are less mature, consistent with their early generation from the deeper lacustrine freshwater source beds and migration to fill the shallower reservoirs first. 16 figs., 2 tabs.

  5. Plant-arthropod interaction in the Early Cretaceous (Berriasian) of the Araripe Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Pires, Etiene Fabbrin; Sommer, Margot Guerra

    2009-02-01

    Plant-arthropod interactions provide the first relevant data for addressing evidence of phytophagy for an assemblage of coniferous silicified woods from the pre-rift phase in the Araripe Basin, Brazil. A complex system of borings, sometimes filled with small, oval to hexagonal coprolites, allow inferences to be made about the activities of termites (Isoptera). Previous dendrological data indicated that the climate during the Early Cretaceous on the landmasses of the northern Afro-Brazilian Depression was dry and savanna like, where termite borings were common. Features of wood preservation demonstrate that the damage was probably caused by herbivores, not detritivores.

  6. [Description of a new species of the genus Astyanax Baird & Girard from Araguaia River basin, Brazil].

    PubMed

    Garutti, V

    1999-11-01

    Astyanax argyrimarginatus sp. n. is described from the Araguaia River basin, Brazil. The new species may be diagnosed by a humeral dark spot horizontally oval, and an elongated caudal peduncle dark spot, continued to the tip of the mid caudal rays, two dark brown vertical bars on the humeral region, and a single black lateral stripe with silvered border. Forty-two to forty-six scales on lateral line; fourteen to sixteen vertical scales rows. Twenty-seven to thirty-one anal fin rays. Dentary large teeth quincuspid, inner row of pre-maxilar teeth quincuspid or hexacuspid, and one maxillary tooth. Comments on the characters which permit to recognize the new species from others with the same color pattern are made.

  7. Moenkhausia celibela: a new species from the Amazon basin, Brazil (Characiformes: Characidae).

    PubMed

    Marinho, M M F; Langeani, F

    2010-09-01

    A new species of Characidae, Moenkhausia celibela, is described from the Rio Amazonas at Santarém, Rio Maraú, several localities in the Rio Tapajós, Rio Curuá-Una, Rio Xingu and Rio Jari, all from the Amazon basin, Brazil. The new species is distinguished from its congeners, except species included in Géry's 1992 Moenkhausia lepidura group, by presenting a dark blotch on the upper caudal-fin lobe, and the lower lobe is hyaline or light grey. Moenkhausia celibela is distinguished from the species of the M. lepidura group by the absence of a humeral spot and the presence of a roughly triangular and dark spot at the caudal-fin base, extending posteriorly along the middle caudal-fin rays, and distinctly separate from the spot on the upper caudal-fin lobe.

  8. Dolomitized cells within chert of the Permian Assistência Formation, Paraná Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Calça, Cléber P.; Fairchild, Thomas R.; Cavalazzi, Barbara; Hachiro, Jorge; Petri, Setembrino; Huila, Manuel Fernando Gonzalez; Toma, Henrique E.; Araki, Koiti

    2016-04-01

    Dolomitic microscopic structures in the form of microspheres, "horseshoe- shaped" objects, and thin botryoidal crusts found within microfossiliferous chert within stromatolites of the Evaporite Bed (EB) of the Permian Assistência Formation, Irati Subgroup, Paraná Basin, Brazil, have been investigated by means of optical microscopy, X-ray fluorescence, scanning electron microscopy, Raman spectrometry and energy-dispersive X-ray spectrometry. The microspheres were identified as dolomitized coccoidal cyanobacteria based on similarity in size, spheroidal and paired hemispheroidal morphologies and colonial habit to co-occurring silicified organic-walled cyanobacteria embedded within the same microfabric and rock samples. The co-occurrence of dolomite, pyrite framboids, and abundant dispersed carbonaceous material and silicified cells is consistent with a hypersaline depositional environment with abundant cyanobacterial mats and elevated Mg2 +/Ca2 + ratios and reducing conditions with active anoxic microbial processes near the water-(bio)sediment interface. The abundance of extracellular polymeric substances facilitated anoxic microbial processes (sulfate reduction), providing essential conditions for possible primary microbially induced dolomitization. In most of the dolomitized cells dolomite occurs only as an external layer; in fully dolomitized cells magnesium is richest in the outermost layer. Presumably, the dolomitization process was favored by the presence of anoxic microbial degraders and negatively charged functional groups at the surface of the cyanobacterial cells. Botryoidal dolomite rims of silica-filled fenestrae formed by a similar process and inherited the botryoidal morphology of the cell as originally lining the fenestrae. Silicification interrupted the dolomitization of the largely organic biosediment, mostly by permineralization, but locally by substitution, thereby preserving not only dolomitic microspheres, but also huge numbers of structurally

  9. Diversity of Non-Biting Midge Larvae Assemblages in the Jacuí River Basin, Brazil

    PubMed Central

    Floss, Elzira Cecília Serafini; Kotzian, Carla Bender; Spies, Márcia Regina; Secretti, Elisangela

    2012-01-01

    The richness and composition of a mountain-river chironomid larvae assemblage in the Jacuí River basin, Brazil were studied, and compared with other riverine non-biting midge larvae assemblages previously studied in the country. Additionally, the influence of some regional-scale environmental characteristics on the spatial distribution of these assemblages was tested. The specimens were collected at 12 sites in the middle course of the Jacuí River basin (in the state of Rio Grande do Sul) between April 2000 and May 2002. Around 100 taxa were recorded. The dominant taxa belonged to the genera Rheotanytarsus, Cricotopus, Polypedilum, and Pseudochironomus. Twenty-two rare taxa were found, representing 22% of the total of taxa inventoried. Fourteen genera (Aedokritus, Axarus, Endotribelos, Kiefferulus, Manoa, Oukuriella, Phaenopsectra, Stenochironomus, Xenochironomus, Xestochironomus, Cardiocladius, Metriocnemus, Paracladius, and Rheocricotopus) represent new occurrences in Rio Grande do Sul. The similarity analysis of the chironomid larvae assemblages inventoried in 32 regions of Brazil indicated five groups with similarity higher than 50%. The groups, when the effects of spatial autocorrelation were removed, displayed a weak positive correlation between the assemblage composition and the aquatic system or hydraulic conditions and the hydrographic basin, and a weak negative correlation in relation to the biome. The altitude showed no correlation with the composition of the assemblage. The relatively high richness of the region surveyed in relation to other Brazilian regions corroborates some tendencies already noted in other parts of the world, such as: i) lotic systems may constitute an exception to the rule that diversity is greater in tropical regions, ii) regions of transitional relief may contain the greatest richness of Chironomidae, and iii) in rivers, the group might have its spatial distribution influenced to a greater extent by local environmental

  10. Early Permian post-glacial bivalve faunas of the Itararé Group, Paraná Basin, Brazil: Paleoecology and biocorrelations with South American intraplate basins

    NASA Astrophysics Data System (ADS)

    Neves, Jacqueline Peixoto; Anelli, Luiz Eduardo; Simões, Marcello Guimarães

    2014-07-01

    The uppermost portion of the Taciba Formation, Itararé Group, Paraná Basin, Brazil, records a succession of depositional environments tied to the demise of late Paleozoic glaciation. In the study area, Teixeira Soares county, state of Paraná, the unit is dominated by massive to laminated diamictites with inclusions of sandstones and other coarse-grained lithotypes, representing re-sedimented material in proximal areas. These are succeeded by fine to medium-grained sandstones with tabular cross-stratification and pectinid-rich shell pavements, interpreted as nearshore deposits. Above this, laminated and intensely bioturbated siltstones with closed articulated bivalve shells are recorded, probably deposited in inner shelf settings. Fine to very fine sandstones/siltstones with hummocky cross-stratification and intercalated mudstones, including infaunal in situ shells, are interpreted as stacked storm deposits, generated in distal shoreface environments. These are succeeded by fossil-poor, massive to laminated siltstones/mudstones or gray shales (=Passinho shale) that are inferred to be outer shelf deposits, generated in organic-rich, oxygen-deficient muddy bottoms. In this sedimentary succession dropstones or ice-rafted debris are missing and locally the Passinho shale marks the maximum flooding surface of the Itararé succession. These are capped by the fluvio-deltaic deposits of the Rio Bonito Formation (Sakmarian-Artinskian). Six facies-controlled, bivalve-dominated assemblages are recognized, representing faunal associations that thrived in aerobic to extreme dysaerobic bottoms along a nearshore-offshore trend. Within these assemblages, nineteen bivalve species (three of them new) were recorded and described in detail. The presence of Myonia argentinensis (Harrington), Atomodesma (Aphanaia) orbirugata (Harrington) and Heteropecten paranaensis Neves et al. suggests correlation with bivalve assemblages of the Eurydesma-bearing Bonete Formation, Pillahuincó Group

  11. Mechanically infiltrated clays: recognition and influence in fluvial reservoirs of Reconcavo basin, Brazil

    SciTech Connect

    Moraes, M.A.S.; De Ros, L.F.

    1989-03-01

    Fluvial sandstones and conglomerates of the Sergi Formation (Jurassic) are the main reservoirs of the Reconcavo basin in northeastern Brazil. These reservoirs contain significant amounts of interstitial detrital clays resulting from early diagenetic mechanical infiltration. The infiltration developed under arid/semiarid conditions, where the lowered water table allowed muddy waters of episodic runoff to infiltrate through the coarse alluvium. The main clay concentrations occurred in the upper phreatic zone and in proximity to sources of influent seepage. It is difficult to identify infiltrated clays in ancient sedimentary rocks due to a lack of well-established petrographic criteria. In this work, a series of petrographic criteria is proposed to recognize these clays in clastic reservoirs. These criteria include the anisophachous coatings of tangentially accreted lamellae and the geometric patterns developed due to shrinkage. The infiltrated clays are among the main controls of reservoir properties, and the horizons of maximum clay concentration are the main internal barriers in most Sergi reservoirs. In general, infiltrated clays damage reservoir quality by creating macroheterogeneities and microheterogeneities, by decreasing recovery efficiency and permeability, and by increasing water saturation. Also, they can cause formation damage either by their swelling properties or through the migration of loose particles left by shrinkage. As demonstrated in the Sergi Formation, infiltrated clays must be adequately identified for the definition of proper procedures for drilling, completion, reservoir development, and EOR programs.

  12. Dealing with variability in water availability: the case of the Verde Grande River basin, Brazil

    NASA Astrophysics Data System (ADS)

    Collischonn, B.; Lopes, A. V.; Pante, A. R.

    2014-09-01

    This paper presents a water resources management strategy developed by the Brazilian National Water Agency (ANA) to cope with the conflicts between water users in the Verde Grande River basin, located at the southern border of the Brazilian semi-arid region. The basin is dominated by water-demanding fruit irrigation agriculture, which has grown significantly and without adequate water use control, over the last 30 years. The current water demand for irrigation exceeds water availability (understood as a 95 % percentile of the flow duration curve) in a ratio of three to one, meaning that downstream water users are experiencing more frequent water shortages than upstream ones. The management strategy implemented in 2008 has the objective of equalizing risk for all water users and consists of a set of rules designed to restrict water withdrawals according to current river water level (indicative of water availability) and water demand. Under that rule, larger farmers have proportionally larger reductions in water use, preserving small subsistence irrigators. Moreover, dry season streamflow is forecasted at strategic points by the end of every rainy season, providing evaluation of shortage risk. Thus, water users are informed about the forecasts and corresponding restrictions well in advance, allowing for anticipated planning of irrigated areas and practices. In order to enforce restriction rules, water meters were installed in all larger water users and inefficient farmers were obligated to improve their irrigation systems' performance. Finally, increases in irrigated area are only allowed in the case of annual crops and during months of higher water availability (November to June). The strategy differs from convectional approached based only on water use priority and has been successful in dealing with natural variability of water availability, allowing more water to be used in wet years and managing risk in an isonomic manner during dry years.

  13. Late Paleozoic paleofjord in the southernmost Parana Basin (Brazil): Geomorphology and sedimentary fill

    NASA Astrophysics Data System (ADS)

    Tedesco, Julia; Cagliari, Joice; Coitinho, Julia dos Reis; da Cunha Lopes, Ricardo; Lavina, Ernesto Luiz Correa

    2016-09-01

    In the southernmost part of the Parana Basin, records of the late Paleozoic glaciation occur in a discontinuous form preserved in paleovalley systems excavated in the crystalline basement. This paper addresses one of these paleovalleys, the Mariana Pimentel, which extends over 60 km with NW-SE valley direction and a constant width of 2.5 km. With the objective of demonstrating that the paleovalley worked as a fjord during the glaciation period, its origin as well as sedimentary fill and morphology were analyzed. The paleovalley morphology was obtained through electrical resistivity (electrical sounding and lateral mapping) and mathematical modeling in four transverse sections. The morphology of the paleovalley documented by the U-shape, steady width, and high depth reaching up to 400 m are typical features of modern glacial valleys. The sedimentary facies that fill the base of the paleovalley, such as rhythmites and dropstones with thickness up to 70 m and diamictites with faceted pebbles (up to 5 m thick) are signs of its glacial origin. During the glaciation period, the paleovalley had a connection to the epicontinental sea located to the northwest, extended toward Namibia, and was excavated by glaciers from the highlands of this region. Thus, the evidence attests that the Mariana Pimentel paleovalley was a fjord during the late Paleozoic glaciation. The duration of the late Paleozoic glaciation (which is longer than the Quaternary glaciation), the apatite fission track that suggests erosion up to 4 km thick in the study area, and the lack of preserved hanging valleys in the Mariana Pimentel indicate that the paleovalley once featured a higher dimension. Furthermore, the existence of paleofjords excavated in the border of the basement corroborates the idea of small ice centers controlled by topography during the late Paleozoic glaciation.

  14. Palynofacies patterns of the Devonian of the Parnaíba Basin, Brazil: Paleoenvironmental implications

    NASA Astrophysics Data System (ADS)

    Trindade, Viviane Segundo Faria; Carvalho, Marcelo de Araujo; Borghi, Leonardo

    2015-10-01

    Event" - has been recorded by other authors. Finally, in the Famennian, woody material was most abundant in Transl/Nbiostr. palynofacies and Sporomorphs palynofacies, which reflects a depositional trend that is strongly controlled by fluvial input into a shallow marine environment.

  15. Ensemble Streamflow Predictions in the Três Marias Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Mainardi Fan, Fernando; Schwanenberg, Dirk; Kuwajima, Julio; Assis dos Reis, Alberto; Collischonn, Walter

    2014-05-01

    Hydropower is the main electricity source of Brazil. The related hydropower reservoirs are multi-purpose thus besides efficient and reliable energy production, they are relevant for flood control. In this context, the present study shows results of an Ensemble Streamflow Prediction (ESP) for supporting the operational decision making implemented at Três Marias hydroelectric power project located in the São Francisco River basin in Brazil. It is a large tropical river basin with approximately 55,000km² up to the Três Marias dam. The hydrological model used in the study is the MGB-IPH (Modelo de Grandes Bacias from Instituto de Pesquisas Hidráulicas), a large scale distributed hydrological model. Applied in an operational forecasting mode, it uses an empirical data assimilation method to take into account real time streamflow observations to update its state variables. We present results of a hindcast experiment with observed precipitation and streamflow data from the local energy utility, CEMIG (Companhia Energética de Minas Gerais), and from the Brazilian water agency, ANA (Agencia Nacional de Água),. Probabilistic Numerical Weather Predictions (NWP) from CPTEC (Centro de Previsão de Tempo e Estudos Climáticos), ECMWF (European Centre for Medium-Range Weather Forecast) and NOAA (National Oceanic and Atmospheric Administration) are used to generate the ESP. The data products and the MGB-IPH model are integrated into an open shell forecasting platform based on the software package Delft-FEWS. Inside the forecasting platform a hindcast mode over a forecast lead time of 10-16 days in recent rainfall periods is applied in. The ESP results are compared to deterministic forecasts of the Três Marias reservoir inflow. The results assessment verifies the added value of the ESP in general in comparison to the use of deterministic forecasts by means of different performance indicators. The ESP derived from the ECMWP ensemble shows the best performance. A future

  16. Estimation of Phosphorus Emissions in the Upper Iguazu Basin (brazil) Using GIS and the More Model

    NASA Astrophysics Data System (ADS)

    Acosta Porras, E. A.; Kishi, R. T.; Fuchs, S.; Hilgert, S.

    2016-06-01

    Pollution emissions into the drainage basin have direct impact on surface water quality. These emissions result from human activities that turn into pollution loads when they reach the water bodies, as point or diffuse sources. Their pollution potential depends on the characteristics and quantity of the transported materials. The estimation of pollution loads can assist decision-making in basin management. Knowledge about the potential pollution sources allows for a prioritization of pollution control policies to achieve the desired water quality. Consequently, it helps avoiding problems such as eutrophication of water bodies. The focus of the research described in this study is related to phosphorus emissions into river basins. The study area is the upper Iguazu basin that lies in the northeast region of the State of Paraná, Brazil, covering about 2,965 km2 and around 4 million inhabitants live concentrated on just 16% of its area. The MoRE (Modeling of Regionalized Emissions) model was used to estimate phosphorus emissions. MoRE is a model that uses empirical approaches to model processes in analytical units, capable of using spatially distributed parameters, covering both, emissions from point sources as well as non-point sources. In order to model the processes, the basin was divided into 152 analytical units with an average size of 20 km2. Available data was organized in a GIS environment. Using e.g. layers of precipitation, the Digital Terrain Model from a 1:10000 scale map as well as soils and land cover, which were derived from remote sensing imagery. Further data is used, such as point pollution discharges and statistical socio-economic data. The model shows that one of the main pollution sources in the upper Iguazu basin is the domestic sewage that enters the river as point source (effluents of treatment stations) and/or as diffuse pollution, caused by failures of sanitary sewer systems or clandestine sewer discharges, accounting for about 56% of the

  17. SEROLOGICAL DETECTION OF HEPATITIS A VIRUS IN FREE-RANGING NEOTROPICAL PRIMATES (Sapajus spp., Alouatta caraya) FROM THE PARANÁ RIVER BASIN, BRAZIL

    PubMed Central

    SVOBODA, Walfrido Kühl; SOARES, Manoel do Carmo Pereira; ALVES, Max Moreira; ROCHA, Tatiana Carneiro; GOMES, Eliane Carneiro; MENONCIN, Fabiana; BATISTA, Paulo Mira; da SILVA, Lineu Roberto; HEADLEY, Selwyn Arlington; HILST, Carmen Lúcia Scortecci; AGUIAR, Lucas M.; LUDWIG, Gabriela; PASSOS, Fernando de Camargo; de SOUZA, Júlio Cesar; NAVARRO, Italmar Teodorico

    2016-01-01

    Nonhuman primates are considered as the natural hosts of Hepatitis A virus (HAV), as well as other pathogens, and can serve as natural sentinels to investigate epizootics and endemic diseases that are of public health importance. During this study, blood samples were collected from 112 Neotropical primates (NTPs) (Sapajus nigritus and S. cay, n = 75; Alouatta caraya, n = 37) trap-captured at the Paraná River basin, Brazil, located between the States of Paraná and Mato Grosso do Sul. Anti-HAV IgG antibodies were detected in 4.5% (5/112) of NTPs, specifically in 6.7% (5/75) of Sapajus spp. and 0% (0/37) of A. caraya. In addition, all samples were negative for the presence of IgM anti-HAV antibodies. These results suggest that free-ranging NTPs were exposed to HAV within the geographical regions evaluated. PMID:26910453

  18. SEROLOGICAL DETECTION OF HEPATITIS A VIRUS IN FREE-RANGING NEOTROPICAL PRIMATES (Sapajus spp., Alouatta caraya) FROM THE PARANÁ RIVER BASIN, BRAZIL.

    PubMed

    Svoboda, Walfrido Kühl; Soares, Manoel do Carmo Pereira; Alves, Max Moreira; Rocha, Tatiana Carneiro; Gomes, Eliane Carneiro; Menoncin, Fabiana; Batista, Paulo Mira; Silva, Lineu Roberto da; Headley, Selwyn Arlington; Hilst, Carmen Lúcia Scortecci; Aguiar, Lucas M; Ludwig, Gabriela; Passos, Fernando de Camargo; Souza Jr, Júlio Cesar de; Navarro, Italmar Teodorico

    2016-01-01

    Nonhuman primates are considered as the natural hosts of Hepatitis A virus (HAV), as well as other pathogens, and can serve as natural sentinels to investigate epizootics and endemic diseases that are of public health importance. During this study, blood samples were collected from 112 Neotropical primates (NTPs) (Sapajus nigritus and S. cay, n = 75; Alouatta caraya, n = 37) trap-captured at the Paraná River basin, Brazil, located between the States of Paraná and Mato Grosso do Sul. Anti-HAV IgG antibodies were detected in 4.5% (5/112) of NTPs, specifically in 6.7% (5/75) of Sapajus spp. and 0% (0/37) of A. caraya. In addition, all samples were negative for the presence of IgM anti-HAV antibodies. These results suggest that free-ranging NTPs were exposed to HAV within the geographical regions evaluated.

  19. Effects of a small natural barrier on the spatial distribution of the fish assemblage in the Verde River, Upper Paraná River Basin,Brazil.

    PubMed

    Silva, J C; Gubiani, É A; Piana, P A; Delariva, R L

    2016-01-01

    Geographical barriers influence species distribution and play an important role in the segregation of fish assemblages. The present study aims to test the influence of a small natural barrier on the spatial distribution of fish species in the Verde River, Upper Paraná River Basin, Brazil, considering two biotopes: upstream and downstream of the Branca Waterfall. We observed the highest species richness downstream of the Branca Waterfall, which also had the highest number of exclusive species. Richness, evenness, and abundance varied significantly among biotopes. The composition and structure of the fish assemblage differed between biotopes, which were characterized by different indicator species, mainly downstream of the Branca Waterfall. Physical and chemical variables and geographical distance between sites were not responsible for the differences observed. Hence, the present study shows that small barriers can also be crucial in structuring fish fauna and play a key role in the segregation of fish assemblages.

  20. New species of Moenkhausia Eigenmann (Characiformes: Characidae) from Rio Xingu and Rio Tapajós basins, Brazil, with comments on a putative case of polymorphic Batesian mimicry.

    PubMed

    Zanata, A M; Birindelli, J L O; Moreira, C R

    2009-12-01

    A new species of Moenkhausia is described from Rio Xingu and Rio Tapajós basins, Brazil. The new species is distinguished from its congeners, except from Moenkhausia moisae, by having more scales in the lateral series, 43-47 (v. 23-41 in the remaining congeners). The new species is distinguished from M. moisae by its colour pattern, which consists of a dark midlateral stripe, and an asymmetrical caudal blotch (inconspicuous or faded in specimens from the Rio Arinos) continuous with the midlateral stripe (v. narrow dark midlateral line and conspicuous, regularly rounded and symmetrical blotch not continuous with the midlateral line). The new species is putatively assumed to be mimetic to Jupiaba apenima, in the Rio Xingu and Rio Teles Pires drainages, and to Jupiaba yarina in the Rio Arinos. The two species of Jupiaba are sympatric and remarkably similar in size, general external morphology and colouration to the new species. A small difference occurs in the colouration between the two species of Jupiaba and is also observed in the two respectively sympatric morphotypes of the new species of Moenkhausia. The occurrence of polymorphic Batesian mimicry is therefore discussed for neotropical freshwater fishes.

  1. Heavy metals and DNA damage in blood cells of insectivore bats in coal mining areas of Catarinense coal basin, Brazil.

    PubMed

    José Zocche, Jairo; Dimer Leffa, Daniela; Paganini Damiani, Adriani; Carvalho, Fernando; Avila Mendonça, Rodrigo; Dos Santos, Carla Eliete Iochims; Appel Boufleur, Liana; Ferraz Dias, Johnny; de Andrade, Vanessa Moraes

    2010-10-01

    We assessed the content of heavy metals in the liver and the DNA damage in blood cells of insectivore bats in the Catarinense Carboniferous Basin, Southern Brazil. Three bats species (Molossus molossus, Tadarida brasiliensis and Eptesicus diminutus) were collected in a coal mining area and in a control area. The heavy metal content in bats was detected according to the PIXE technique and the DNA damage was assessed by the Comet assay. The contents of Cr, Ni, Cu and Pb in M. molossus and of Cu and Fe in T. brasiliensis from the coal mining area was higher than in the animals from the control area. In both areas differences in metal contents in the liver were observed between the bat species. The parameters assessed by the Comet assay were significantly higher in E. diminutus as compared to M. molossus and T. brasiliensis. Values of both Comet assay parameters were significantly higher in the mining area as compared to the control area only for T. brasiliensis.

  2. Seasonal study of concentration of heavy metals in waters from lower São Francisco River basin, Brazil.

    PubMed

    Souza, A M; Salviano, A M; Melo, J F B; Felix, W P; Belém, C S; Ramos, P N

    2016-01-01

    In this study we determined the concentration of metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in the water lower São Francisco River basin, to evaluate the influence of urbanization and industrialization on environmental changes in the water resource. All samples were analyzed using the IUPAC adapted method and processed in an atomic absorption spectrophotometer. The sampling stations located near the industrial areas were influenced by industrialization because they presented higher concentrations of Cd, Cr, Ni and Cu. The other sampled locations showed changes with regard the trace elements probably originating in the soil, like Fe, Zn and Pb. There was a gradual increase in the concentrations of metals, in general, in the period of highest rainfall of the hydrographic network. Overall, except for Zn and Mn, the trace elements exceeded the maximum allowed value established by national legislation (CONAMA). Lower São Francisco River basin has suffered interference from urbanization and industrialization, so awareness programs should be developed so as to control and lessen future problems.

  3. Shelf-fed turbidite system model and its application to the Oligocene deposits of the Campos Basin, Brazil

    SciTech Connect

    Peres, W.E. )

    1993-01-01

    Despite the large number of models involving the genesis and sedimentary facies of deep-water sandstones, none of these models adequately explain the origin and evolution of the extremely clean, widespread (over 6000 km[sup 2]), predominantly massive, thick (over 150 m), blanket-like sandstones deposited in the deep-water environment of the Campos Basin during the Oligocene. Consequently, to explain this sandstone, the author proposes a shelf-fed turbidite system model, which is strongly based on the Campos Basin data set. The basic framework necessary for the development of a shelf-fed turbidite system includes (1) deposition of a large volume of clastics during the buildup of a shelf-sand-rich unit, which later constitutes the main source of sediment for the system, (2) localized tectonic pulses that modify the outer shelf declivity and trigger mass flows; and (3) a relative fall of sea level, which causes the subaqueous exposure of the shelf sediments to reworking in a shallow, high-energy marine environment. These three basic elements are equally important for shelf-fed turbidity system development, but relative sea level position controls the development of the progradational, aggradational, and retrogradational depositional phases within the system. Submarine canyons commonly are scoured during all three phases on the outer shelf and lower slope environments. The shelf-fed turbidite system model may apply to other sedimentary basins, principally to those of the Atlantic-continental margins that have a thick evaporite sublayer. Halokinesis can provide the necessary room for the shelf sedimentary-unit buildup, the tectonic pulses that trigger the flows, and even localized relative sea level oscillations that can accelerate or abort any one of the depositional phases of the system. 25 refs., 26 figs.

  4. A new Permian bivalve-dominated assemblage in the Rio do Rasto Formation, Paraná Basin, Brazil: Faunal turnover driven by regional-scale environmental changes in a vast epeiric sea

    NASA Astrophysics Data System (ADS)

    Simões, Marcello Guimarães; Matos, Suzana Aparecida; Anelli, Luiz Eduardo; Rohn, Rosemarie; Warren, Lucas Veríssimo; David, Juliana Machado

    2015-12-01

    The basal portion of the Permian Rio do Rasto Formation (Serrinha Member), Passa Dois Group, Paraná Basin, Brazil, records an entirely new bivalve fauna intercalated between the underlying Pinzonella neotropica assemblage (uppermost portion of the Teresina Formation) and the overlying Leinzia similis assemblage (Rio do Rasto Formation). Mollusks of these assemblages lived in marginal shallow-water habitats of an immense epeiric sea and were dominated by endemic bivalve species. Taxonomic analysis revealed the presence of Terraia curvata (60.61%), Astartellopsis prosoclina (19.70%), Cowperesia emerita (10.61%), Leinzia curta (4.55%), Terraia bipleura (3.03%) and Beurlenella elongatella (1.52%), which are associated with conchostracans and plant remains. Species composition, abundance, and dominance in this novel assemblage differ notably from the preceding ones, suggesting a substantial evolutionary turnover. Regional-scale environmental changes recognized based on taphonomy, facies analysis, and geochemical data consist of progressive freshening of the marginal habitats of the Paraná Basin and taxic changes that include the following: (a) loss of genera, (b) decrease in bivalve abundance and ecological guilds, (c) disappearance of the dominant bivalve group (Pinzonellinae) and (d) diversification of Terrainae bivalves. The ecological signature also changed notably because only infaunal suspension-feeding bivalves are present, indicating a significant loss of functional diversity at the regional scale. Likely stressor factors (among others) are tied to freshening events, suggesting profound changes in (a) salinity, (b) primary productivity and (c) a lack of coarse, stable substrates coupled with high bioturbation rates. Hence, our regional example could offer valuable clues to benthic (bivalve) community responses in a habitat subjected to (a) rapid climate changes and (b) freshening events in shallow-water settings. Finally, the stratigraphic range of the

  5. Rare Carboniferous and Permian glacial and non-glacial bryophytes and associated lycophyte megaspores of the Paraná Basin, Brazil: A new occurrence and paleoenvironmental considerations

    NASA Astrophysics Data System (ADS)

    Ricardi-Branco, Fresia; Rohn, Rosemarie; Longhim, Marcia Emilia; Costa, Juliana Sampaio; Martine, Ariel Milani; Christiano-de-Souza, Isabel Cortez

    2016-12-01

    Fossil bryophytes are rare because their preservation is compromised by the presence of a thin cuticle (if any) and a lack of lignin. Except for the occurrence of one bryophyte in the glacial Dwyka Group of the Karoo Basin, the other rare Late Paleozoic records in Gondwana are notably from the Paraná Basin in Southeast/South Brazil. Four bryophyte sites (including a newly discovered one) were found in the lower part of the thick Permo-Carboniferous glacial succession of the Itararé Group, and one was found in the Guadalupian Teresina Formation, which was roughly assigned to an epeiric sea (or "lake") dominated by a warm, semi-arid climate. This study describes the fossils from the new occurrence from the Itararé Group and discusses the context in which the bryophyte beds originated in the basin. The new samples confirm that all of the bryophytes of the Itararé Group can be classified as Dwykea araroii Ricardi-Branco et al. (a possible pleurocarp) and are associated with the lycophyte megaspore Sublagenicula brasiliensis (Dijkstra) Dybová-Jachowicz. In the much younger Teresina Formation, the bryophytes are Yguajemanus yucapirus Cristiano-de-Souza et al. and Capimirinus riopretensis Cristiano-de-Souza et al., and abundant charophytes and rare dwarf lycophyte stems and bracts are present in the same layers. Although the two stratigraphic units represent distinct paleoenvironments and climates, they seem to share some characteristics: a) the bryophyte assemblages were transported very little; b) they were deposited in very calm environments; c) they were the main components (along with some lycophytes) of local or poorly diversified regional vegetation. The low number of species, which is characteristic of opportunistic communities, can be explained by local or regional conditions that would have been stressful for the vascular plants in other areas. During the deposition of the Itararé Group, the main control was probably the cold climate in addition to a

  6. Detecting Light Hydrocarbon Microseepages and related Intra-sedimentary Structures at the São Francisco Basin, Brazil, using Airborne Geophysical Data

    NASA Astrophysics Data System (ADS)

    Curto, J. B.; Pires, A. C.; Silva, A.; Crosta, A. P.

    2011-12-01

    The use of indirect techniques for the detection of light hydrocarbons occurrences on the surface, named as microseepages, has been used to augment hydrocarbon exploration. Surveys developed for this type of application are normally targeted at mapping the effects that microseepages cause on the environment. In Brazil, most available airborne geophysical surveys were not appropriately designed for this type of application and, thus far they have been mostly used to define the main basin structural features. Existing microseepages are known in Remanso do Fogo area (Minas Gerais State, Brazil), located in São Francisco Basin, where the Quaternary sedimentary cover made the identification of new occurrences and associated controlling structures quite difficult. This study investigates the spatial distribution of hydrocarbon related structures in shallower to intra-sedimentary depths in the Remanso do Fogo area, using airborne magnetic and gamma-ray spectrometry data. These data were managed by the ANP (Brazilian Petroleum National Agency) and conducted by Lasa Engineering & Surveys in 2006. In the study area, data were acquired along north-south flight lines spaced 500 m apart and along orthogonal tie lines flown 4 Km apart at a terrain clearance of 100 m. The geophysical data were processed using techniques developed to suppress the influence of regional geological signatures. For the magnetic data, this study focuses on the enhancement of intra-sedimentary structures and possible near surface accumulations of diagenetic magnetic minerals, provided by hydrocarbon related chemical reactions. The amplitude of the analytic signal, calculated with second order derivatives, combined with the total horizontal gradient of the subtraction between the 1200 and 400 meter upward continuations, illuminated the NW and EW magnetic lineaments, which are partially related to the microseepages and the drainage of the area. The distinction of near-surface and deeper signatures also

  7. Depositional environment, diagenetic history, and reservoir geology of the Santiago member sandstones of the Pojuca Formation (Lower Cretaceous) in the Aracas oil field, Reconcavo basin, Brazil

    SciTech Connect

    Couto dos Anjos, S.M.

    1987-01-01

    Core analysis, sand isolith maps, shape of SP curves, and comparison with recent depositional models defined crevasse mouth bar, distal bar, bay fill, and transitional (distal bar/bay) environments. The best potential reservoirs occur in crevasse mouth bar deposits. Ten microfacies were defined, namely, two wackes, six arenites which are the most frequent in all sandstone bodies (S-1 to S-5), and two carbonates. The diagenetic evolution of the various microfacies of the Santiago sandstone is very similar and comprises: destruction of primary porosity by compaction and burial cementation; development of secondary porosity by leaching of cements; decrease in secondary porosity by late cementation and compaction; and preservation of secondary porosity due to oil migration which halted further diagenetic evolution. Framework grains, cements, and porosity in the S-2, S-3, and S-4 reservoirs display different distribution patterns. Framework grains display patterns similar to those of depositional environment whereas cements and porosity patterns reflect predominantly diagenetic processes. They show closed geometry indicating the effect of a dome-like structure of compaction origin which probably controlled the circulation of pore fluids. Highest values of porosity occur in the least cemented areas with exception of the matrix-rich interval (S-4) where the reverse values of porosity and cement are not observed. The distribution pattern of permeability is complex, and does not follow that of porosity. It does not seem to be directly related to any observable variation in framework grains or cements.

  8. Molecular signature of the D-loop in the brown pencilfish Nannostomus eques (Characiformes, Lebiasinidae) reveals at least two evolutionary units in the Rio Negro basin, Brazil.

    PubMed

    Terencio, M L; Schneider, C H; Porto, J I R

    2012-07-01

    The genetic variability of the brown pencilfish Nannostomus eques was studied, based on an analysis of sequences from the control region (1084 bp) of mitochondrial (mt)DNA in 125 individuals collected from eight tributaries along the upper (Açaituba, Miuá, Jaradi and Arixanã), middle (Demini), and lower (Jacundá, Maguari and Catalão) Rio Negro (Brazil). Phylogenetic inferences using mtDNA data from N. eques revealed two evolutionary units. Genetic distance between them ranged from 5.5 to 8.3% and differed by 8.5-11.8% from the sister species pencilfish Nannostomus unifasciatus. The time of divergence between the two evolutionary units was estimated to be the Middle Pliocene (c. 2.99 million years before present). Population genetic analysis (DNA polymorphism, AMOVA and Mantel test) showed high haplotype diversity (HD, >0.90) in each evolutionary unit, a strong population genetic structure in the Demini River that formed a monophyletic group and a correlation between genetic divergence and geographical distance in only one of these units (evolutionary unit 1). On the basis of molecular data, the rapids and waterfalls near São Gabriel da Cachoeira (Upper Rio Negro) were the main barriers to gene flow within evolutionary unit 1 in some localities. The emergences of the Branco River and the Anavilhanas Archipelago were apparently responsible for the discrepancy in distribution of the two evolutionary units, except at Jacundá, where the evolutionary units were sympatric. In view of the differences between the evolutionary units, N. eques cannot be treated as a single stock in the Rio Negro basin. These results may have important implications for the fishery management of this ornamental fish.

  9. Effects of non-aqueous fluids-associated drill cuttings discharge on shelf break macrobenthic communities in the Campos Basin, Brazil.

    PubMed

    Santos, Maria Fernanda L; Silva, Janete; Fachel, Jandyra M G; Pulgati, Fernando H

    2010-08-01

    This paper assesses the effects of non-aqueous fluids (NAF)-associated drill cuttings discharge on shelf break macrobenthic communities in the Campos Basin, off the southeast Brazilian coast, Rio de Janeiro State. Samples were taken with a 0.25-m2 box corer from surrounding two oil and gas wells on three monitoring cruises: before drilling, three months after drilling, and 22 months after drilling. Statistical methodologies used Bayesian geostatistical and analysis of variance models to evaluate the effects of the NAF-associated drill cuttings discharge and to define the impact area. The results indicated that marked variations were not observed in the number of families between cruises, though there were changes in the fauna composition. The changes seen in biological descriptors in both control and background situation areas were not considered significant, showing a temporal homogeneity in means. The impact area presented changes in biological descriptors of communities and trophic structure during the three cruises and such changes were correlated to chemical and physical variables related to the drilling activities, as a result of the mix of drill cuttings and sediment and the anoxic conditions established in the substrate. In that area, three months after drilling, a decrease in diversity and an increase in density, motile deposit-feeders and Pol/Crp ratio, and dominance of opportunistic organisms, such as the capitellid Capitella sp., were observed and, 22 months after drilling, an increase of diversity, reduction of dominance of capitellid polychaete, changes in the fauna composition, and a dominance of opportunistic burrowing and tube-building organisms were observed, indicating an ecological succession process.

  10. Infrastructure sufficiency in meeting water demand under climate-induced socio-hydrological transition in the urbanizing Capibaribe River basin - Brazil

    NASA Astrophysics Data System (ADS)

    Ribeiro Neto, A.; Scott, C. A.; Lima, E. A.; Montenegro, S. M. G. L.; Cirilo, J. A.

    2014-09-01

    impact over the water supply in the basin, mainly for human use. Industry and irrigation will suffer impact unless other measures are implemented for demand control.

  11. Mixed carbonate-siliciclastic sedimentation in forebulge grabens: An example from the Ediacaran Bambuí Group, São Francisco Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Reis, Humberto L. S.; Suss, João F.

    2016-06-01

    continuous over most of the Sete Lagoas basement high, showing remarkable variations within the studied forebulge grabens. Our analysis demonstrates that the depositional architecture of Sequence 1 and Sequence 2 marks the interplay of successive episodes of tectonically driven forebulge uplift and regional eustatic and climatic changes. The latter are mainly recorded by the lower second-order sequence (Sequence 1), which contains typical sedimentary features deposited in the aftermath of an important glaciation affecting lower latitudes during the late Neoproterozoic. An additional local accommodation control is restricted to the forebulge grabens and is associated with episodic and local subsidence pulses. As indicated by lower- to higher-rank cycles, it has been responsible for the deposition of thicker transgressive to early regressive successions, a few gravitational flow deposits, and the development of the deltaic to shallow marine carbonate cycles of Sequence 2. The overall stratigraphic architecture of the studied successions suggests that several basin mechanisms operating during the Phanerozoic were also present in the late Neoproterozoic. The close association between organic-rich post-glacial shales, potential reservoir facies, and rift-related migration paths and hydrocarbon traps indicate that forebulge grabens represent important elements to consider in hydrocarbon exploration campaigns.

  12. Petroleum geology of Solimoes Basin, Brazil

    SciTech Connect

    Campos, J.N.P.; Meister, E.M.; Pereira, C.A.G.; Murakami, C.Y. )

    1993-02-01

    Solimoes basin is located at the northwestern portion of the South American continent, adjacent to a subandean pericratonic belt. It constitutes a Paleozoic intracratonic basin covering an area of about 600,000 km[sup 2] and displaying a maximum sedimentary thickness of 3400 m. The tectono-sedimentary evolution can be largely related with important events that occurred at the western border of the continent. The regional flexural subsidence and tectonic deformation observed are correlated to two major phases: Pre-Andean (Paleozoic) and Andean (Mesozoic and Cenozoic). In the Andean phase, compression with shear components, of Triassic age, known as the Jurua Tectonism, became very important for oil exploration of the basin. The stratigraphic conditions considered of greatest interest for petroleum exploration comprise Devonian gas and oil sourcing shales and Carboniferous sandstones reservoirs with an evaporitic seal. The main traps are anticlines related to reverse faults. In this context, Petrobras discovered Jurua gas field in 1978 and the Rio Urucu gas and oil field in 1986. These were the first fields discovered in Brazilian Paleozoic basins. Total petroleum fields discovered in Brazilian Paleozoic basins. Total petroleum reserves discovered represent 400 million bbl of equivalent oil. Present migration and accumulation call for previous accumulation in intrabasinal Paleozoic highs and related stratigraphic traps. Late tectonism seems to have resulted in redistribution and/or escape of fluids into new traps. Less disturbed areas are expected to contain original accumulations.

  13. Geology of petroleum in Campos basin, Brazil

    SciTech Connect

    Meister, E.M.

    1984-04-01

    A schematic model of oil generation, migration, accumulation, and alteration is presented for the Campos basin, a sedimentary province covering an area of nearly 31,000 km/sup 2/ (12,000 mi/sup 2/) offshore southeastern Brazil, where an estimated 1 billion m/sup 3/ (6.3 billion bbl) of oil in place has been discovered since 1974. Source rocks for this oil belong to the Lower Cretaceous Lagoa Feia Formation; oil generation probably started in the Miocene. At that time, a series of local windows opened in the regional evaporite seal at the top of the Lagoa Feia Formation and focused the upward escape of hydrocarbons, mainly along halokinetic fault surfaces. Reservoirs of Albian, Late Cretaceous, and Tertiary age were charged and their porosities enhanced by natural fracturing, solution, and/or grain rearrangement. Original oil (postulated range of 30/sup 0/-35/sup 0/ API gravity) underwent differentiation by migration, reflected in relative enrichment of aromatics and of the light /sup 12/C stable carbon isotope. Alteration of oil by water occurs if one of the two fluids in contact is allochthonous; bacterial alteration is important in low-temperature regimes. Oil entrapment is helped by hydrodynamic conditions, with the intake area of the Paraiba do Sul river delta supposedly playing an important part. Lopatin-type plots gave the first clue for establishing this model, which takes into account a large number of facts about the basin, such as well and seismic information, clay diagenesis, water and petroleum geochemistry, pressure data, and their geologic field relationships.

  14. Oil migration examples in Irati Formation, Parana basin, Brazil

    SciTech Connect

    Espitalie, J.; Mizuta, K.; Carvalho, T.E.M.; Triguis, J.A.

    1983-03-01

    The Irati Formation (Late Permian), in the Parana basin, is a source rock with high oil generating potential. The TOC contents range from 0.5 to 13% according to the quality of the organic matter. Pyrolysis analysis indicates that the area where the Irati has the highest oil-generating source rock is in the north and south of the Parana basin. In these areas petroleum potential can reach 90 kg HC/t of rock. In the central part of the basin the Irati Formation might reach a depth of about 3200 m (10,498 ft). In many wells diabase intrusions have more or less completely cooked this formation, thus generating oil or gas, and leaving residual organic matter. The phenomenon of migration into the Irati Formation has been observed in many wells. In certain places, oil is accumulated in shales embedded between intrusion levels; in other places oil is accumulated into limestone beds, intercalated in the Irati Formation. It seems safe to assume that the oil accumulated in the deeper beds resulted from the effect of thermal intrusions and also from the effects of normal burial. Oil migration occurred after diabase intrusions (Late Cretaceous) during the increasing subsidence of the basin. In the Parana basin, the Irati Formation may be compared to a drain with a lateral oil migration. Vertical migration was hindered by the lack of enough porosity and permeability in the shales above the Irati source rock. Consequently, migration and accumulation of oil above and below the formation might have resulted from changes in facies of the Irati itself, by faulting, or by fractures due to diabase intrusions.

  15. Regional magnetotelluric surveys in hydrocarbon exploration, Parana' Basin, Brazil

    SciTech Connect

    Stanley, W.D.; Ohofugi, W.; Saad, A.R.

    1985-03-01

    The magnetotelluric geophysical method has been used effectively as a hydrocarbon exploration tool in the intracratonic Parana basin of South America. The 1-2 km thick surface basalts and buried diabase sills pose no problem for the magnetotelluric method because the natural electromagnetic fields used as the energy source pass easily through the basalt. Data for the regional study were taken on six profiles with soundings spaced 8 to 15 km apart. The magnetotelluric sounding data outline a linear uplift known as the Ponta Grossa arch. This major structural feature cuts across the northeast-trending intracratonic basin almost perpendicularly, and is injected with numerous diabase dikes. In the survey area, MT interpretations show that basalts have aggregate thicknesses of as much as 2 km (6,600 ft), and basement may be as much as 6 km (20,000 ft) below the surface. Over most of the basin, the basalts are covered by Upper Cretaceous to Holocene continental sediments of a few hundred meters thickness and are underlain by 2 to 4 km (6,600 to 13,100 ft) thick Paleozoic sediments with possible hydrocarbon potential. Significant electrical contrasts occur between the Permian sediments and older units, so that magnetotelluric measurements can give an indication of the regional thickness of the Permian and younger sediments to aid in interpreting hydrocarbon migration patterns and possible trap areas.

  16. REGIONAL MAGNETOTELLURIC SURVEYS IN HYDROCARBON EXPLORATION, PARANA BASIN, BRAZIL.

    USGS Publications Warehouse

    Stanley, William D.; Saad, Antonio; Ohofugi, Walter

    1985-01-01

    The mangetotelluric geophysical method has been used effectively as a hydrocarbon exploration tool in the intracratonic Parana basin of South America. The 1-2 km thick surface basalts and buried diabase sills pose no problem for the magnetotelluric method because the natural electromagnetic fields used as the energy source pass easily through the basalt. Data for the regional study were taken on six profiles with sounding spaced 8 to 15 km apart. The magnetotelluric sounding data outline a linear uplift known as the Ponta Grossa arch. This major structural feature cuts across the northeast-trending intracratonic basin almost perpendicularly, and is injected with numerous diabase dikes. Significant electrical contrasts occur between the Permian sediments and older units, so that magnetotelluric measurements can give an indication of the regional thickness of the Permian and younger sediments to aid in interpreting hydrocarbon migration patterns and possible trap areas. Refs.

  17. Using magnetotellurics in regional hydrocarbon exploration of Parana basin, Brazil

    SciTech Connect

    Stanley, W.D.; Saad, R.A.; Ohofugi, W.

    1984-04-01

    The magnetotelluric (MT) method has been utilized in a multidisciplinary exploration program recently completed in the Parana basin by the State of Sao Paulo. In the deeper portions of the Parana basin, MT interpretations show that basalts have thicknesses of up to 2 km (6500 ft) and that basement may be as much as 6 km (19,700 ft) below the surface. In most of the basin, the basalts are covered by thin units of Upper Cretaceous to Holocene continental sediments and are underlain by 2-4 km (6500-13,000 ft) of prospective Paleozoic sediments. In addition, interpretation of the MT sounding data with layered and fault-dike models outlines a linear uplift known as the Ponta Grossa arch. Permian Irati sediments are an important source unit classified as mostly in the oil window. Good electrical contrasts occur between the Permian sediments and older units, so that MT measurements can indicate the regional thickness of the Permian and younger sediments for use in interpretation of migration patterns and possible traps. In addition to providing this stratigraphic information, MT and aeromagnetic surveys have delineated the influence of the Sao Francisco craton in truncating uplift and tensional features of the Ponta Grossa arch.

  18. Geology and major oil plays, Coastal Margin basins, Brazil

    SciTech Connect

    Mosmann, R.; Fisher, W.L.

    1984-04-01

    Six major tectonic-depositional sequences, reflecting rift and passive margin evolution, variously characterize the filling of Brazilian coastal margin basins: (1) Late Jurassic prerift, (2) Early Cretaceous tectonic rift, (3) Early Cretaceous quiescent stage (evaporitic or calcilutitic), (4) middle Cretaceous platform/deltaic progradational and deep marine retrogradation, and (6) Tertiary main passive margin progradation. Habitat of oil discovered to date meets two regional geologic conditions: (1) in tectonic rifts known to have basin core of starved, lacustrine shales, and (2) in basins which developed a quiescent phase during the transition from tectonic rift to passive margin. Two major plays characterize the central core rifts, including (I) underlying prerift sediments in fault contact with the central core, and (II) sublacustrine fans overlying the central core. These plays, typified in the Reconcavo basin, constitute about half the recoverable oil found to date. Exploration implications of the established plays are: (1) source is from tectonic or quiescent stage fill (Aptian or older); (2) structural integrity of the quiescent stage seals is critical to oil migration; and (3) tectonic rifts are productive when a core of deep lacustrine shales was developed.

  19. Hydrologic investigations in the Araguaia-Tocantins River basin (Brazil)

    USGS Publications Warehouse

    Snell, Leonard J.

    1979-01-01

    The Araguaia-Tocantins River basin system of central and northern Brazil drains an area of about 770,000 square kilometers and has the potential for supporting large-scale developments. During a short visit to the headquarters of the Interstate Commission for the Araguaia-Tocantins Valley and to several stream-gaging stations in June 1964, the author reviewed the status of the streamflow and meteorological data-collection programs in relation to the streamflow and meteorological data-collection programs in relation to the pressing needs of development project studies. To provide data for areal and project-site studies and for main-stream sites, an initial network of 33 stream gaging stations was proposed, including the 7 stations then in operation. Suggestions were made in regard to operations, staffing and equipment. Organizational responsibilities for operations were found to be divided uncertainly. The Brazilian Meteorological Service had 15 synoptic stations in operation in and near the basin, some in need of reconditioning. Plans were at hand for the addition of 15 sites to the synoptic network and for limited data collection at 27 other sites. The author proposed collection of precipitation data at about 50 other locations to achieve a more representative areal distribution. Temperature, evaporation, and upper-air data sites were suggested to enhance the prospective hydrometeorological studies. (USGS)

  20. Three-Dimensional Oil Dispersion Model in Campos basin, Brazil.

    PubMed

    Oliveira, Bernardo Lopes Almeida de; Netto, Theodoro Antoun; Assad, Luiz Paulo de Freitas

    2017-02-22

    This paper presents the physical and mathematical formulation of a three-dimensional oil dispersion model that calculates the trajectory from the seafloor to the sea surface, its assumptions and constraints. It was developed by researchers that are familiar with oil spill dispersion and mathematical analysis. Oil dispersion is calculated through two computational routines. The first calculates the vertical dispersion along the water column and resamples the droplets when the oil reaches the surface. The second calculates the surface displacement of the spill. This model is based on the Eulerian Approach, and it uses numerical solution schemes in time and in space to solve the equation for advective-diffusive transport. A case study based on an actual accident that happened in the Campos Basin, in Rio de Janeiro State, considering the instant spill of 1.000 m(3) was used to evaluate the proposed model. After calculating the vertical transport, it was estimated that the area covered by the oil spill on the surface was about 35.685 m². After calculating the dispersion at the surface, the plume area was estimated as 20% of the initial area, resulting in a final area of 28.548 m².

  1. Cassiopidae gastropods, influence of Tethys Sea of the Romualdo Formation (Aptian-Albian), Araripe Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Pereira, Priscilla Albuquerque; Cassab, Rita de Cassia Tardin; Barreto, Alcina Magnólia Franca

    2016-10-01

    The Cassiopidae family belongs to a group of gastropods of the Tethyan Realm, whose origin and dispersion are related a transgression of the Tethys Sea during the Early Cretaceous. The Romualdo Formation in the Araripe Basin, located in Northeast Brazil, presents fossil assemblages with echinoids, bivalves and cassiopid gastropods, indicating a marine sedimentation at the top of the formation. This research reveals three new species of this fauna: Gymnentome (Craginia) beurleni sp. nov., 'Pseudomesalia' ('Pseudomesalia') mennessieri sp. nov and 'Pseudomesalia' ('Pseudomesalia') santanensis sp. nov. We also review two other species: Craginia araripensisBeurlen, 1964 and Gymnentome romualdoiBeurlen, 1964, which we reclassify taxonomically as Paraglauconia (Diglauconia) araripensis and Gymnentome (Gymnentome) romualdoi, respectively; Paraglauconia (Diglauconia) lyrica Maury, 1936 and Gymnentome (Gymnentome) carregozica Maury, 1936 were the first recorded species in the Araripe Basin. The occurrence of these cassiopid gastropod fauna in other basins, such as Sergipe, Potiguar and Parnaíba, indicate the influence of waters coming from the north through the Tethys Sea in the Aptian-Albian and in the marginal continental basins of the Brazilian Northeast.

  2. Seismic Traveltime Tomography Applied to Data from Miranga Field, Reconcavo Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Bassrei, A.; Rodrigues, V.

    2015-12-01

    The growing global demand for hydrocarbons has tested the limits of oil exploration and exploitation technologies. Within the seismic methods, tomography is an alternative for the high resolution characterization of reservoirs, enabling a more efficient recovery of new as well as mature fields. In this work, seismic traveltime tomography in the transmission mode was applied to real data from the Miranga Field, Reconcavo Basin, State of Bahia, Brazil. This basin represents a landmark of oil exploration in Brazil and has been intensively studied since the 1950s. Today, the Reconcavo Basin is still the principal oil producer in the State of Bahia, but there is a demand for new technologies, especially for mature fields, to improve hydrocarbon recovery. The objective is to estimate the two-dimensional velocity distribution in the region between the two wells. We have used linearized inversion through the Levenberg-Marquardt scheme. The input data in the system are the traveltimes between the sources and the receivers and the distances propagated by each ray connecting such sources and receivers. Both inputs are provided through acoustic forward modeling. The conjugate gradient algorithm with regularization through derivative matrices was used as an inverse procedure. The tomographic inversion is an ill-posed problem because the existence, uniqueness and stability conditions are not completely satisfied. The linear system is regularized by derivative matrices derived to minimize the instability. This regularization procedure has a crucially important parameter called regularization parameter lambda. For the selection of lambda we used L-curve and Theta-curve. The estimated tomograms were consistent with previous geological knowledge of the area and the P-wave velocity range was consistent. The results showed that traveltime tomography is feasible for the characterization of reservoirs with a high rate of vertical change, similar to the Miranga Field.

  3. Inversion of Seismic Cross-hole Data from Dom Joao Field, Reconcavo Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Bassrei, A.; Oliveira, N. P. D.

    2014-12-01

    Seismic Tomography was incorporated in Reservoir Geophysics with the intention of providing high-resolution images of regions in the Earth's subsurface that are characterized as potential reservoirs. In this work, seismic traveltime tomography in the transmission mode was applied to real data from the Dom Joao Field, Reconcavo Basin, State of Bahia, Brazil. This basin represents a landmark of oil exploration in Brazil and has been intensively studied since the 1950s. Today, the Reconcavo Basin is still the principal oil producer in the State of Bahia, but there is a demand for new technologies, especially for mature fields, to improve hydrocarbon recovery. Acoustic ray tracing for the computation of traveltimes was used for forward modeling, and the conjugate gradient algorithm with regularization through derivative matrices was used as an inverse procedure. The tomographic inversion is an ill-posed problem because the existence, uniqueness and stability conditions are not completely satisfied. Mathematical techniques are commonly used with the intention of providing better conditioning for the numerical solution of such problems. The input data in the system are the traveltimes between the sources and the receivers and the distances propagated by each ray connecting such sources and receivers. Both inputs are provided through acoustic forward modeling. The linear system is regularized by derivative matrices derived to minimize the instability. This regularization procedure has a crucially important parameter called regularization parameter lambda. For the selection of lambda we used the L-module, which is based on the well-known L-curve. The estimated tomograms were consistent with previous geological knowledge of the area and the P-wave velocity range was consistent. The results showed that traveltime tomography is feasible for the characterization of reservoirs with a high rate of vertical change, similar to the Dom Joao Field.

  4. Atmospheric precipitation and chemical composition of an urban site, Guaíba hydrographic basin, Brazil

    NASA Astrophysics Data System (ADS)

    Migliavacca, D.; Teixeira, E. C.; Wiegand, F.; Machado, A. C. M.; Sanchez, J.

    The purpose of the present work was to study the chemical composition of bulk and wet atmospheric precipitation in the Guaíba Hydrographic Basin, in South Brazil. The samples were analyzed from January to December 2002 at three different stations, i.e., 8° Distrito and CEASA stations in the city of Porto Alegre, and Charqueadas station, located in the city of same name. The bulk and wet precipitation were analyzed for conductivity, pH, Cl -, NO 3-, F -, SO 42-, Na +, K +, Mg 2+, NH 4+, Ca 2+, Cu, Zn, Mn, Fe and Al. The pH values in the samples of atmospheric precipitation ranged between 4.75 and 7.45. The analysis of linear regression applied to the set of studied variables showed that neutralization occurred in samples of bulk and wet precipitation. It was found that the Cl present in samples of atmospheric precipitation originated from sea salts and anthropogenic sources. The principal components analysis (PCA) identified the main anthropogenic sources within the Guaíba Hydrographic Basin (GHB). Cluster analysis grouped the events identified for each station in the PCA in association with the meteorological data.

  5. A new large species of Myloplus (Characiformes, Serrasalmidae) from the Rio Madeira basin, Brazil

    PubMed Central

    Andrade, Marcelo C.; Jégu, Michel; Giarrizzo, Tommaso

    2016-01-01

    Abstract Myloplus zorroi sp. n. is described from the Rio Madeira Basin in Amazonia. The new species had been treated as an undescribed Tometes species because of the absence of a marked abdominal keel and few small spines forming its prepelvic serrae, features commonly found in the species of the Myleus clade of the Serrasalmidae (species of genera Myleus, Mylesinus, Ossubtus and Tometes) and also in species of Utiaritichthys. Myloplus zorroi sp. n. shares the following characters with its congeners and Utiaritichthys: molariform teeth (versus incisiform teeth in Myleus clade members); a labial row of premaxillary teeth separated from lingual row by an internal gap (versus absence of internal gap between premaxillary teeth rows); and an ascending process of premaxilla wide from its base to the tip (versus ascending process tapering from its base to the tip). Like other Myloplus species, Myloplus zorroi sp. n. differs from Utiariticthys by having a deeper body, approximately 60% of standard length (versus usually less than 50% of standard length). Considering all the morphological evidence, including the presence of 13–19 low spines forming the prepelvic serrae in Myloplus zorroi sp. n. versus more than 20 high spines forming a marked prepelvic keel in other species of Mylopus, the new species is here assigned to Myloplus. Comparisons of the new species with nominal species of Myloplus, representatives of the Myleus clade, and other related taxa are provided. PMID:27110164

  6. A New Species of Tiger Pleco Panaqolus (Siluriformes: Loricariidae) from the Xingu Basin, Brazil.

    PubMed

    Cramer, Christian Andreas; Melo de Sousa, Leandro

    2016-01-01

    Panaqolus tankei is described from the Xingu River, Brazil. The new species is diagnosed from P. albomaculatus, P. dentex, P. nix, P. nocturnus, and P. koko by its color pattern consisting of dark and light diagonal bars on the body and bands on the fins (vs. body and fins without bars or bands); from P. albivermis, P. maccus, and P. purusiensis by the width of the dark bars being more or less the same of the light bars (vs. dark bars at least two or three times wider than light bars) and from P. changae by the absence of vermiculation on the head (vs. vermiculation present on head). The new species differs from P. gnomus by the orientation of the bars from posterodorsal to anteroventral direction (vs. anterodorsal to posteroventral direction), and from P. claustellifer by the orientation of the bands in the dorsal fin that are not parallel to the margin (vs. parallel to the margin). The barcoding region (COI) was sequenced for the new species, sequences were deposited in GenBank and were compared with congeners from other drainages. With regard to the current construction of a hydroelectric power plant (a so-called mega dam) in the Xingu River, herewith we increase knowledge of the river Xingu's ichthyofauna and, thus improve the assessment of the impacts of that construction on the river.

  7. Effects of deforestation and climate variability on the hydrological balance of the Xingu River Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Panday, P. K.; Coe, M. T.; Macedo, M.; Castanho, A. D. D. A.; Lefebvre, P.

    2014-12-01

    High historical deforestation rates and a rapidly changing agricultural landscape are altering the energy and water balance of the eastern Amazon basin. The headwaters of Xingu River Basin (XB; Area: 510,000 km2) in the southeastern Amazon have seen some of the highest rates of deforestation, resulting in a decrease of average basin forest cover from about 90% in the 1970s to 75% in the 2000s. This study examines the water balance of the XB and attributes the influences of climate variations and deforestation using a diverse set of observational and modeling tools including; long-term observations of rainfall and discharge, satellite-based estimates of evapotranspiration (MODIS) and surface water storage (GRACE), and numerical model output (IBIS) of the set of hydrological components (evapotranspiration, soil moisture, and discharge). This water budget of the 2000s is first estimated by explicitly including deforestation over the 2001-2010 through integration of the modeled outputs with forest cover information from MODIS. Modeled outputs from the 1970s to the 2000s are then used to estimate the effects on the Xingu water budget due to climate variability, historical deforestation, or both. The decadal mean water balance components of the IBIS simulation over the 2001-2010, compares well with the satellite-derived and field-based observational estimates. Analysis of the individual components of change from the 1970s to the 2000s indicates that climate variability and land cover change have had opposite influences with climate effects masking the changes in water budget due to historical deforestation. Changes in land cover due to deforestation have decreased ET by ~3% and increased soil moisture by ~1% in XB, leading to increased discharge on average by 8% from the 1970s to the 2000s.

  8. Conodont color alteration index and upper Paleozoic thermal history of the Amazonas Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Cardoso, Cassiane Negreiros; Sanz-López, Javier; Blanco-Ferrera, Silvia; Lemos, Valesca Brasil; Scomazzon, Ana Karina

    2015-12-01

    The conodont color alteration index (CAI) was determined in elements from core samples of the Frasnian Barreirinha Formation (one well) and of the Pennsylvanian-Permian Tapajós Group (twenty three wells and one limestone quarry) in the Amazonas Basin. The thermal history of the basin is analyzed using the CAI value distribution represented in maps and stratigraphic sections through correlation schemes, and in conjunction with previously published data. The pattern of palaeotemperatures for CAI values of 1.5-3 is coincident with organic matter maturation under a sedimentary overburden providing diagenetic conditions in the oil/gas window. Locally, conodonts show metamorphism (CAI value of 6-7) in relation to the intrusion of diabase bodies in beds including high geothermal gradient evaporites. Microtextural alteration on the surface conodonts commonly shows several types of overgrowth microtextures developed in diagenetic conditions. Locally, recrystallization in conodonts with a high CAI value is congruent with contact metamorphism in relation to Mesozoic intrusions. The CAI values of 1.5 or 2 observed close to the surface in several areas of the basin may be interpreted in relation to a high thermal palaeogradient derived from the magmatic episode or/and to the local denudation of the upper part of the Paleozoic succession prior to this thermal event.

  9. A new species of Centromochlus (Siluriformes, Auchenipteridae, Centromochlinae) from the middle Rio Tocantins basin, Brazil.

    PubMed

    Birindelli, J L O; Sarmento-Soares, L M; Lima, F C T

    2015-10-01

    A new species of the catfish genus Centromochlus (Auchenipteridae, Centromochlinae) is described. The new species is diagnosed by having numerous dark rounded blotches over the body and fins, dorsal-fin spine with serrations anteriorly and smooth posteriorly, anal fin of mature males with three unbranched and seven branched rays, anterior nuchal plate absent and posterior nuchal plate not extended ventrally. The new species is described from a small stream in the Estação Ecológica Serra Geral de Tocantins, a natural reserve in the centre of the Brazilian Cerrado, close to the watershed between the Rio Tocantins and the Rio São Francisco basins. The new species is possibly the sister taxon to the recently described Centromochlus meridionalis from the upper Rio Tapajós. Those two species share with Centromochlus perugiae, from the upper Amazon and upper Paraguay, derived features associated with the modified anal fin in sexually mature males.

  10. Seasonal and interannual litter dynamics of a tropical semideciduous forest of the southern Amazon Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Sanches, Luciana; Valentini, Carla Maria Abido; Júnior, Osvaldo Borges Pinto; de Souza Nogueira, José; Vourlitis, George Louis; Biudes, Marcelo Sacardi; da Silva, Carlos José; Bambi, Paulino; de Almeida Lobo, Francisco

    2008-12-01

    This study analyzed how seasonal and interannual variations in climate alter litter dynamics, including production, decomposition, and accumulation. Monthly measurements of leaf, stem, and reproductive (flower plus fruit) litter and the forest floor litter mass were combined with a mass balance model to determine rates of litter decomposition for a semideciduous tropical forest located in the rain forest-savanna ecotone of the southern Amazon Basin for 2001-2007. Annual rates of litter production varied between 8 and 10.5 Mg ha-1 a-1, and leaf litter production accounted for the majority (˜70%) of the total litter production. Leaf litter production peaked at the end of the May-August dry season while stem litter production peaked during the wet season and reproductive litter production peaked during the dry-wet season transition. Forest floor litter mass ranged between 5 and 8 Mg ha-1 over the study period and generally declined as litter inputs declined. Litter decomposition rates were remarkably stable from year-to-year and varied between 10.8 and 12.4 Mg ha-1 a-1. On average, rates of litter decomposition were highest during the dry-wet season transition. Overall, our results suggest that rainfall variability directly altered litter production dynamics and indirectly altered forest floor litter mass and decomposition kinetics through its effect on litter production. Future changes in seasonal and/or interannual rainfall patterns, whether in response to El Niño or to anthropogenic climate change, will likely have important consequences for the litter dynamics of Amazonian semideciduous forest.

  11. The microbial nature of laminated limestones: Lessons from the Upper Aptian, Araripe Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Catto, Bruno; Jahnert, Ricardo Jorge; Warren, Lucas Verissimo; Varejao, Filipe Giovanini; Assine, Mario Luis

    2016-07-01

    The Araripe Basin, located in northeastern Brazil, originated during the Gondwana continental break-up responsible for the opening of the South Atlantic during the Early Cretaceous. In the Araripe Basin, the post-rift Aptian sequence corresponds to the Santana Group, which is composed, in upward succession, of mostly clastic continental and rare carbonate layers of the Barbalha, Crato, Ipubi and Romualdo Formations. The laminated limestones of the Crato Formation were deposited in a lacustrine environment preceding the deposition of the Ipubi Formation evaporites. They are age-equivalent to the limestones of the pre-salt interval of the east coast of Brazil, which contains large petroleum reserves. The excellent preservation of its macrofossils has made the Crato Formation known worldwide as a Fossil Lagerstätte. The limestones are macroscopically homogeneous, and their deposition has been previously attributed to chemical precipitation. Although the carbonate laminites are macroscopically undifferentiated, mineralogical variations, microscopic texture and distinctive biotic aspects supported the characterization of four microfacies: planar laminated, crustiform, nodular and rhythmic. The microfacies analysis indicated a strong and pervasive biological activity in the Crato limestone morphogenesis. Organominerals precipitated by the metabolic action of cyanobacteria and/or sulfate-reducing bacteria and methanogenic-oxidizing archea are represented by calcite and pyrite. Calcified coccoid and filaments are common, furthermore, the presence of calcified biofilms composed of exopolymeric substances (EPS) is ubiquitous. The presence of amorphous organic matter (AOM) and gypsum, particularly in the rhythmic microfacies, indicates anoxic/dysoxic conditions and stressful environments during periods of drought and low lake levels which favored the development and preservation of microbial biofilms. Phytoclasts and miospores when present in the succession indicate an extrabasinal contribution during wetter periods, although the environment remained of very low energy. The evidence of microbial influence in the formation of the laminated limestones of the Crato Formation is of great importance for understanding the excellent preservation of the unit's fossils and for modeling the evolution of the Aptian carbonate sequences in Brazil.

  12. Why deep drilling in the Colônia Basin (Brazil)?

    NASA Astrophysics Data System (ADS)

    Ledru, M.-P.; Reimold, W. U.; Ariztegui, D.; Bard, E.; Crósta, A. P.; Riccomini, C.; Sawakuchi, A. O.

    2015-12-01

    The Colônia Deep Drilling Project held its first International Continental Scientific Drilling Program (ICDP) workshop in September 2014 at the University of São Paulo (Brazil). Twenty-seven experts from six countries discussed the feasibility and the expectations of a deep drilling in the structure of Colônia located at the southwestern margin of the city of São Paulo. After presenting the studies performed at the site during the last decades, participants focused on the objectives, priorities and detailed planning for a full deep-drilling proposal. An excursion to the site and new auger coring showed the importance of the Colônia site for studying the evolution of a tropical rainforest and to evaluate the interplay between the South American summer monsoon, the Intertropical Convergence Zone (ITCZ) and the southern Westerlies belt during the last 5 million years. In addition, deep drilling will eventually solve the still unresolved issue of the origin of the structure of Colônia as a result of meteorite impact or endogenous processes.

  13. Petroleum geology of Campos Basin, Brazil: A successful case history of deep water exploration

    SciTech Connect

    Franke, M.R.; Lugon, H.A.F.; Beraldo, W.L. )

    1990-05-01

    Campos Basin, the most prolific Brazilian basin, produces almost 400,000 bbl of oil per day and contains 70% of the national reserves. The basin is located on the southeastern coast of Brazil, covering a prospectable area of 100,000 km{sup 2} Campos is a passive continental margin basin originated by the breakup of Pangea and the rifting of the South American and African plates in the Early Cretaceous. The basin's sedimentary section encompasses three megasequences: nonmarine, transitional, and marine, ranging in age from Neocomian to Holocene. Hydrocarbon generation is related to nonmarine organic-rich shales and marls, and hydrocarbon entrapment assumes ascendent migration along fault planes and through salt gaps toward reservoirs ranging in age from Neocomian to Tertiary (mainly turbiditic sandstones). The first onshore stratigraphic well was drilled based on gravity surveys in 1958. The acquisition of new geophysical data, mainly seismic reflection data, followed after 1968. The first offshore well was drilled in 1971, and in 1974, the first oil field, Garopua, was discovered. Giant hydrocarbon accumulations have been discovered in water depths ranging from 400 to 1,800 m since 1984. As of mid-1989, 35 offshore oil fields have been discovered, 760 million bbl of oil, and 490 bcf of gas have been produced. The basin oil and equivalent gas reserves are estimated in 6.0 billion bbl, 60% of which is located in the deep-water giant oil fields.

  14. Shelf-edge sedimentary systems off Rio de Janeiro State, northern Santos basin-Brazil

    NASA Astrophysics Data System (ADS)

    Maia, R. M. C.; Dos Reis, A. T.; Gorini, C.; Silva, C. G.; Rabineau, M.; Granjeon, D.

    2012-04-01

    The sedimentary record of the continental shelf off Rio de Janeiro State is related to the opening and evolution of Atlantic Ocean. The combined analysis of high resolution seismic acquired in the early 80's (Geomar cruises) and 2D seismic lines of petroleum industry, coupled with chronostratigraphic data from oil industry's exploratory wells, allowed us to observe two different orders of sequences: of 3-4th order, that represents sedimentary units related of the Milankovitch cycles (100/40/20ky), and of 2nd order (10-100my). High resolution seismic allowed us to outline a first architectural framework for the actual shelf that is composed of stacked seismic units making up the major seismic sequences bounded by angular unconformities. According to the intern and extern configuration of their clinoforms, the seismic sequences were grouped into two distinctive stratigraphic sets, identified as Set I (Pliocene) and Set II (Upper Quaternary). Some architectural components of note include: (1) the characteristic upbuilt-outbuilt geometry of sequences that compose Set I (SqA, SqB and SqC), indicating that deposition has probably been favoured by a combination of prevailing subsidence regime (upbuilt pattern) accompanied by forced regressive deposits (outbuilt pattern); (2) the majority of sequences that make up Set II outbuilts as a composite seaward-thickening progradational wedge formed under dominant forced regression conditions, implying that the generation of accommodation space was less important than during the build-up of Set I. However, these sequences consistently pinch out in a progressively landward direction, suggesting a prevailing and increasing subsidence regime able to induce the progressive seaward tilting of the margin during the middle-late Pleistocene, and the subsequent partial preservation of regressive sequences of about 100-200 m thick at the level of the present-day mid-shelf, that prograded seaward for circa 15-25 km. These architectural elements provide a hint at a prevailing subsidence regime and effective sediment supply into the basin that clearly contrast with the conveyed idea of a sediment-starved and tectonic stable shelf. They naturally raise questions about the nature and origin of sediment supply, since no significant point siliciclastic fluvial source flows directly into the shelf. Stemming from that, we are forced to speculate about: (A) the role of neotectonic movements involving the Serra do Mar coastal mountain ranges to potentially source clastic influx into the basin during the Quaternary, or about the real importance of secondary drainage basins debouching today; and (B) the mechanical nature of a supposed subsidence during the Pliocene and the Quaternary time span (overloading ? sediment compaction ? thermal cooling ?). The interpretation of industrial seismic lines can provide the answers of many of these questions. The next step of this work is to make a stratigraphy model of the sedimentary systems of Santos basin to understand how the ancient creation of accommodation space can influence the recent sedimentary architecture and how is the change in sedimentary influx and the sedimentary records of different orders of cyclicity.

  15. Preliminary Measurements Of N2O Partial Pressures In Rivers of Amazon Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Oliveira, C. B.; Rasera, M. F.; Krusche, A. V.; Victoria, R. L.; Richey, J. E.; Cunha, H. B.; Gomes, B. M.

    2006-12-01

    The concentrations of nitrous oxide (N2O), an important component of the greenhouse effect and with a long residence time in the atmosphere, have significantly increased in this century. The reasons for this atmospheric increase in N2O are still partially unexplained. This uncertainty is worse in relation to aquatic environments. Here we report on preliminary measurements of N2O partial pressures in rivers of the Amazon basin. The study areas are in the state of Rondonia (rivers Ji Parana, Urupa, Comemoracao and Pimenta Bueno) and Amazonas (rivers Solimoes and Negro). The rivers were sampled from October 2005 to April 2006, using with immersion pumps, lowered in the middle of the channel to 60% of total depth. Water was pumped directly into a 1 l plastic bottle, which was overflown three times before closing. Using syringes, 60 ml of N2 were injected into the bottle, simultaenously to the withdrawn of 60 ml of sample. N2O was extracted into these 60 ml of N2 by shaking vigorously for 2 minutes. With the same syringes, the gas was taken from the bottles and injected into sealed evacuated 25 ml vials. Atmospheric samples were taken from one meter above the water column and stored the same way. N2O partial pressures were determined on a Shimadzu GC-14 Green House Gas Analyzer. All rivers showed little variations in N2O partial pressures. Average values in the rivers of Rondonia were around 0.41 ± 0.07 μ atm (n=46), whereas the Solimoes and Negro rivers, in the state of Amazonas, showed values around 0.43 ± 0.08 μ atm (n=131). Atmospheric averages were approximately 0.34 ± 0.04 μ atm (n=58) and 0.32 ± 0.03 μ atm (n=134) in the states of Rondonia and Amazonas, respectively. This means that, although these waters are supersatured in CO2, making evasive fluxes of this gas an important component of the C cycle in this basin, the same does not occur in the N cycle. Small differences in partial pressures of N2O between water and air will result in small fluxes of this gas to the atmosphere from the middle of the river channels. However, at the river margins and riparian zones, significantly different redox conditions may occur, which should be further investigated to fully understand the role of N2O fluxes in these riverine systems.

  16. Sustainability assessment of water hyacinth fast pyrolysis in the Upper Paraguay River basin, Brazil.

    PubMed

    Buller, Luz Selene; Ortega, Enrique; Bergier, Ivan; Mesa-Pérez, Juan Miguel; Salis, Suzana Maria; Luengo, Carlos Alberto

    2015-11-01

    Fast pyrolysis of naturally produced water hyacinth was assessed through Emergy accounting approach. Two analyses were carried out to evaluate the influence of additional services and externalities on Emergy indicators for a pyrolysis plant unit able to process 1000 kg of dry biomass per hour. The initial approach was a traditional Emergy assessment in which financial fluxes and externalities were not considered. The second approach included taxes and fees of the Brazilian government, interests related to financing operations and assumes a reserve financial fund of 5% of the total investment as externalities cost. For the first evaluation, the renewability of 86% indicates that local and renewable resources mainly support the process and the Emergy Yield Ratio of 3.2 shows that the system has a potential contribution to the regional economy due to the local resources use. The inclusion of financial fluxes and externalities in the second evaluation reduces both renewability and Emergy Yield Ratio, whereas it increases the Emergy Investment Ratio which means a higher dependence on external resources. The second analysis allows portraying significant forces of the industrial and financial systems and the evaluation of the externalities' impact on the general system Emergy behavior. A comparison of the renewability of water hyacinth fast pyrolysis with other biofuels like soybean biodiesel and sugarcane ethanol indicates that the former is less dependent on fossil fuel resources, machinery and fertilizers. To complement the sustainability assessment provided by the Emergy method, a regular financial analysis for the second defined system was done. It shows that the system is financially attractive even with the accounting of additional costs. The results obtained in this study could be used as the maximum and minimum thresholds to subsidize regulatory policies for new economic activities in tropical wetlands involving natural resources exploitation and bio-industrial systems.

  17. Stress variability in the Parnaíba Basin, Brazil, during Cretaceous rifting

    NASA Astrophysics Data System (ADS)

    Ibanez, Delano M.; Pestilho, André L. S.; Turra, Bruno B.; Destro, Nivaldo; Miranda, Fernando P.; Riccomini, Claudio; Lammoglia, Talita; Dubois, Daniel S.; Schmidt, Jaques S.

    2017-03-01

    The Cretaceous section of the Parnaíba Basin, designated as Grajaú Basin, represents an intracontinental half-graben formed during the Early Cretaceous due to the separation between the South American and African continents during the final dispersal of Western Gondwana. Here, through a synergetic approach between fluid inclusion planes (FIPs), outcropping geologic structures, borehole breakouts and remote sensing data, we elucidate in different scales the main structural features and their kinematic indicators. Normal faults strike mainly NNE-SSW and WNW-ESE, while deformation bands and extension joints trend to NW-SE and NE-SW, and FIPs to NE-SW and WNW-ESE. In addition, normal fault-generated scarps border geomorphological units and constitute dense zones of deformation bands and fluidization. Microthermometric FIP analyses suggest this fracturing event occurred at shallow basin levels, at temperatures below 50 °C. Furthermore, joints, bands and FIPs present mutually cross-cutting relationships, thus indicating contemporaneity. The numerical inversions applied to striated faults, non-striated faults, joints, deformation bands and FIPs suggest the occurrence of an extensional event characterized by variable direction of extension (σ3) trending from NW-SE to WNW-ESE or NE-SE to NNE-SSW. This event probably started in the Albian during the final Gondwana fragmentation stages. The quasi-perpendicular σ3 trend could be caused by one or all of the following phenomena: a) stress ratio R values obtained (< 0.4) indicate the possibility of radial extension (σ2 ≈ σ3), perhaps in response to the deformation partitioning due to kinematic simple-shearing constraints along the Equatorial Atlantic transform margin; b) along the WNW-oriented release normal faults, the local extension (NNE-SSW) switch positions in relation to the regional extension (WNW-ESE) by rotating 90°; c) influence of the pre-existing structures on the regional stress field. Thus, the spatial and temporal relationships between Cretaceous fault activity, stress field and the development of the geomorphological features in the Grajaú Basin contribute to understanding of the Brazilian Equatorial margin geodynamics.

  18. Stress magnitude and orientation in the Potiguar Basin, Brazil: Implications on faulting style and reactivation

    NASA Astrophysics Data System (ADS)

    Reis, Álvaro F. C.; Bezerra, Francisco H. R.; Ferreira, Joaquim M.; Nascimento, Aderson F.; Lima, Cláudio C.

    2013-10-01

    analyzed borehole breakout data and drilling-induced tensile fractures derived from resistivity image logs run at 10 oil wells to derive the orientation of the maximum horizontal stress SHmax from the Potiguar Basin in the continental margin of Brazil. Stress magnitudes are derived from density logs for the vertical stress, mini-frac tests for the minimum horizontal stress Shmin, and rock strength laboratory analysis to estimate the SHmax magnitudes. We compared these results with the stress regime and SHmax orientation derived from nine earthquake series located in the crystalline basement, where seismicity is concentrated, and previous breakout data from the basin. In the basin, the SHmax gradient is 20.0 MPa/km, and the SHmax/Shmin ratio is 1.154, indicating a normal tectonic stress regime from 0.5 to 2.0 km, whereas the SHmax gradient of 24.5 MPa/km and SHmax/Shmin ratio of 1.396 indicate a transition from a normal to strike-slip stress regime at 2.5 to 4.0 km. The deeper stress regime in the basin is similar to that in the basement at 1-12 km depth. This transition of the tectonic stress regime is consistent with an incipient tectonic inversion in the basin. We note that the SHmax orientation rotates from NW-SE in the western part of the Potiguar Basin to E-W in its central and eastern parts, roughly following the shoreline geometry, indicating that local features such as flexural stresses influence the local (scale < 100 km) stress pattern. We also conclude that the basement is critically stressed, but not the basin.

  19. Shear-strength signatures of mass movements, continental slope of Campos Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Kowsmann, R. O.; da Costa, A. M.; Amaral, C. S.

    2003-04-01

    Downhole shear-strength profiles, obtained from cone-penetrometer and lab tests were tied to sedimentary facies from adjacent continuous cores. The geotechnical response of mass-transport deposits was investigated. In the Campos Basin, sediments have evacuated from the upper continental slope and have accumulated as folded deposits on the middle slope. Sediment removal is recognised by an abrupt step-like increase in shear-strength at the level of the unconformity. The folded deposits are characterised by a belly-shaped increase in shear-strength coinciding with a zone of intense lamination within the deposit, induced by internal shearing and fluid loss (strain hardening). In contrast, highly disintegrated muddy debris-flow deposits are indistinguishable, in terms of shear-strength, from normal hemipelagic slope sediments. Debris-flow tongues emanating from canyon mouths, which contain a significant amount of more consolidated mud clasts can however be differentiated from in situ sediments by their serrated signature and higher shear-strength.

  20. Carbon isotope discrimination in forest and pasture ecosystems of the Amazon Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Ometto, Jean P. H. B.; Flanagan, Lawrence B.; Martinelli, Luiz A.; Moreira, Marcelo Z.; Higuchi, Niro; Ehleringer, James R.

    2002-12-01

    Our objective was to measure the stable carbon isotope composition of leaf tissue and CO2 released by respiration (δr), and to use this information as an estimate of changes in ecosystem isotopic discrimination that occur in response to seasonal and interannual changes in environmental conditions, and land-use change (forest-pasture conversion). We made measurements in primary forest and pastures in the Amazon Basin of Brazil. At the Santarém forest site, δr values showed a seasonal cycle varying from less than -29‰ to approximately -26‰. The observed seasonal change in δr was correlated with variation in the observed monthly precipitation. In contrast, there was no significant seasonal variation in δr at the Manaus forest site (average δr approximately -28‰), consistent with a narrower range of variation in monthly precipitation than occurred in Santarém. Despite substantial (9‰) vertical variation in leaf δ13C, the average δr values observed for all forest sites were similar to the δ13C values of the most exposed sun foliage of the dominant tree species. This suggested that the major portion of recently respired carbon dioxide in these forests was metabolized carbohydrate fixed by the sun leaves at the top of the forest canopy. There was no significant seasonal variation observed in the δ13C values of leaf organic matter for the forest sites. We sampled in pastures dominated by the C4 grass, Brachiaria spp., which is planted after forest vegetation has been cleared. The carbon isotope ratio of respired CO2 in pastures was enriched in 13C by approximately 10‰ compared to forest ecosystems. A significant temporal change occurred in δr after the Manaus pasture was burned. Burning removed much of the encroaching C3 shrub vegetation and so allowed an increased dominance of the C4 pasture grass, which resulted in higher δr values.

  1. Carbon Isotope Discrimination in Forest and Pasture Ecosystems of the Amazon Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Ehleringer, J. R.; Ometto, J.; Ometto, J.; Flanagan, L. B.; Martinelli, L. A.; Moreira, M. Z.; Higuchi, N.

    2001-12-01

    Our objective was to measure the stable carbon isotope composition of leaf tissue and CO2 released by respiration (\\deltaR), and to use this information as an estimate of changes in ecosystem isotopic discrimination that occur in response to seasonal and interannual changes in environmental conditions, and land-use change (forest-pasture conversion). We made measurements in primary forest and pastures in the Amazon Basin of Brazil. At the Santarem forest site \\deltaR values showed a seasonal cycle varying from less than -29\\permil to approximately -26\\permil. The observed seasonal change in \\deltaR was correlated with variation in the average monthly precipitation. In contrast there was no significant seasonal variation in \\deltaR at the Manaus forest site (average δ _{R} approximately -28‰ ), consistent with a narrower range of variation in monthly precipitation than occurred in Santarem. Despite substantial (9‰ ) vertical variation in leaf δ ^{13}C, the average δ _{R} values observed for both forest sites were similar to the δ ^{13}C values of the most exposed, sun foliage of the dominant tree species. This suggested that the major portion of recently respired carbon dioxide in these forests was metabolized carbohydrate fixed by the sun leaves at the top of the forest canopy. There was no significant seasonal variation observed in the δ ^{13}C values of leaf organic matter for the forest sites. We sampled in pastures dominated by the C_{4} grass, Brachiaria spp., which is planted after forest vegetation has been cleared. The carbon isotope ratio of respired CO_{2} in pastures was enriched in ^{13}C by approximately 10‰ compared to forest ecosystems. A significant temporal change occurred in δ _{R} after the Manaus pasture was burned. Burning removed much of the encroaching C_{3} shrub vegetation and so allowed an increased dominance of the C_{4} pasture grass, which resulted in higher δ _{R}$ values.

  2. A New Species of Tiger Pleco Panaqolus (Siluriformes: Loricariidae) from the Xingu Basin, Brazil

    PubMed Central

    Melo de Sousa, Leandro

    2016-01-01

    Panaqolus tankei is described from the Xingu River, Brazil. The new species is diagnosed from P. albomaculatus, P. dentex, P. nix, P. nocturnus, and P. koko by its color pattern consisting of dark and light diagonal bars on the body and bands on the fins (vs. body and fins without bars or bands); from P. albivermis, P. maccus, and P. purusiensis by the width of the dark bars being more or less the same of the light bars (vs. dark bars at least two or three times wider than light bars) and from P. changae by the absence of vermiculation on the head (vs. vermiculation present on head). The new species differs from P. gnomus by the orientation of the bars from posterodorsal to anteroventral direction (vs. anterodorsal to posteroventral direction), and from P. claustellifer by the orientation of the bands in the dorsal fin that are not parallel to the margin (vs. parallel to the margin). The barcoding region (COI) was sequenced for the new species, sequences were deposited in GenBank and were compared with congeners from other drainages. With regard to the current construction of a hydroelectric power plant (a so-called mega dam) in the Xingu River, herewith we increase knowledge of the river Xingu’s ichthyofauna and, thus improve the assessment of the impacts of that construction on the river. PMID:27828981

  3. Seismic activity triggered by water wells in the Paraná Basin, Brazil

    NASA Astrophysics Data System (ADS)

    AssumpçãO, Marcelo; Yamabe, Tereza H.; Barbosa, José Roberto; Hamza, Valiya; Lopes, Afonso E. V.; Balancin, Lucas; Bianchi, Marcelo B.

    2010-07-01

    Triggered seismicity is commonly associated with deep water reservoirs or injection wells where water is injected at high pressure into the reservoir rock. However, earth tremors related solely to the opening of groundwater wells are extremely rare. Here we present a clear case of seismicity induced by pore-pressure changes following the drilling of water wells that exploit a confined aquifer in the intracratonic Paraná Basin of southeastern Brazil. Since 2004, shallow seismic activity, with magnitudes up to 2.9 and intensities V MM, has been observed near deep wells (120-200 m) that were drilled in early 2003 near the town of Bebedouro. The wells were drilled for irrigation purposes, cross a sandstone layer about 60-80 m thick and extract water from a confined aquifer in fractured zones between basalt flow layers. Seismic activity, mainly event swarms, has occurred yearly since 2004, mostly during the rainy season when the wells are not pumped. During the dry season when the wells are pumped almost continuously, the activity is very low. A seismographic network, installed in March 2005, has located more than 2000 microearthquakes. The events are less than 1 km deep (mostly within the 0.5 km thick basalt layer) and cover an area roughly 1.5 km × 5 km across. The seismicity generally starts in a small area and expands to larger distances with an equivalent hydraulic diffusivity ranging from 0.06 to 0.6 m2/s. Geophysical and geothermal logging of several wells in the area showed that water from the shallow sandstone aquifer enters the well at the top and usually forms waterfalls. The waterfalls flow down the sides of the wells and feed the confined, fractured aquifer in the basalt layer at the bottom. Two seismic areas are observed: the main area surrounds several wells that are pumped continuously during the dry season, and a second area near another well (about 10 km from the first area) that is not used for irrigation and not pumped regularly. The main area displays cyclic annual activity, but the second area does not. We explain the earthquake swarms as being triggered by pore pressure diffusion in the fractured basalt layer due to additional pressure from the newly connected surface aquifer. This reaches critically prestressed areas up to a few kilometers away from the wells. During periods of continuous pumping, the reduction of pore pressure in the confined aquifer stops the seismic activity. Our study suggests that this kind of activity may be more common than previously thought and implies that many other cases of small tremors associated with the drilling of water wells may have gone unnoticed.

  4. Artificial maturation of oil shale: The Irati Formation from the Parana Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Gayer, James L.

    Oil shale samples from the Irati Formation in Brazil were evaluated from an outcrop block, denoted Block 003. The goals of this thesis include: 1) Characterizing the Irati Formation, 2) Comparing the effects of two different types of pyrolysis, anhydrous and hydrous, and 3) Utilizing a variety of geophysical experiments to determine the changes associated with each type of pyrolysis. Primary work included determining total organic carbon, source rock analysis, mineralogy, computer tomography x-ray scans, and scanning electron microscope images before and after pyrolysis, as well as acoustic properties of the samples during pyrolysis. Two types of pyrolysis (hydrous and anhydrous) were performed on samples cored at three different orientations (0°, 45°, and 90°) with respect to the axis of symmetry, requiring six total experiments. During pyrolysis, the overall effective pressure was maintained at 800 psi, and the holding temperature was 365°C. The changes and deformation in the hydrous pyrolysis samples were greater compared to the anhydrous pyrolysis. The velocities gave the best indication of changes occurring during pyrolysis, but it was difficult to maintain the same amplitude and quality of waveforms at higher temperatures. The velocity changes were due to a combination of factors, including thermal deformation of the samples, fracture porosity development, and the release of adsorbed water and bitumen from the sample. Anhydrous pyrolysis in this study did not reduce TOC, while TOC was reduced due to hydrous pyrolysis by 5%, and velocities in the hydrous pyrolysis decreased by up to 30% at 365°C compared to room temperature. Data from this study and future data that can be acquired with the improved high-temperature, high-pressure experiment will assist in future economic production from oil shale at lower temperatures under hydrous pyrolysis conditions.

  5. A 4D-variational ocean data assimilation application for Santos Basin, Brazil

    NASA Astrophysics Data System (ADS)

    da Rocha Fragoso, Mauricio; de Carvalho, Gabriel Vieira; Soares, Felipe Lobo Mendes; Faller, Daiane Gracieli; de Freitas Assad, Luiz Paulo; Toste, Raquel; Sancho, Lívia Maria Barbosa; Passos, Elisa Nóbrega; Böck, Carina Stefoni; Reis, Bruna; Landau, Luiz; Arango, Hernan G.; Moore, Andrew M.

    2016-03-01

    Aiming to achieve systematic ocean forecasting for the southeastern Brazilian coast, an incremental 4D-Var data assimilation system is applied to a regional ocean model focused mainly in the Santos Basin region. This implementation is performed within the scope of The Santos Basin Ocean Observing System (or Project Azul), a pilot project designed to collect oceanographic data with enough frequency and spatial coverage so to improve regional forecasts through data assimilation. The ocean modeling and data assimilation system of Project Azul is performed with the Regional Ocean Modeling System (ROMS). The observations used in the assimilation cycles include the following: 1-day gridded, 0.1° resolution SST from POES AVHRR; 1-day gridded, 0.3° composite of the MDT SSH from AVISO; and surface and subsurface hydrographic measurements of temperature and salinity collected with gliders and ARGO floats from Project Azul and from UK Met-Office EN3 project dataset. The assimilative model results are compared to forward model results and independent observations, both from remote sensing and in situ sources. The results clearly show that 4D-Var data assimilation leads to an improvement in the skill of ocean hindcast in the studied region.

  6. Palynostratigraphy and sedimentary facies of Middle Miocene fluvial deposits of the Amazonas Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Dino, Rodolfo; Soares, Emílio Alberto Amaral; Antonioli, Luzia; Riccomini, Claudio; Nogueira, Afonso César Rodrigues

    2012-03-01

    Palynostratigraphic and sedimentary facies analyses were made on sedimentary deposits from the left bank of the Solimões River, southwest of Manaus, State of Amazonas, Brazil. These provided the age-dating and subdivision of a post-Cretaceous stratigraphic succession in the Amazonas Basin. The Novo Remanso Formation is subdivided into upper and lower units, and delineated by discontinuous surfaces at its top and bottom. The formation consists primarily of sandstones and minor mudstones and conglomerates, reflecting fluvial channel, point bar and floodplain facies of a fluvial meandering paleosystem. Fairly well-preserved palynoflora was recovered from four palynologically productive samples collected in a local irregular concentration of gray clay deposits, rich in organic material and fossilized wood, at the top of the Novo Remanso Formation upper unit. The palynoflora is dominated by terrestrial spores and pollen grains, and is characterized by abundant angiosperm pollen grains ( Tricolpites, Grimsdalea, Perisyncolporites, Tricolporites and Malvacearumpollis). Trilete spores are almost as abundant as the angiosperm pollen, and are represented mainly by the genera Deltoidospora, Verrutriletes, and Hamulatisporis. Gymnosperm pollen is scarce. The presence of the index species Grimsdalea magnaclavata Germeraad et al. (1968) indicates that these deposits belong to the Middle Miocene homonymous palynozone (Lorente, 1986; Hoorn, 1993; Jaramillo et al., 2011). Sedimentological characteristics (poorly sorted, angular to sub-angular, fine to very-coarse quartz sands facies) are typical of the Novo Remanso Formation upper part. These are associated with a paleoflow to the NE-E and SE-E, and with an entirely lowland-derived palinofloristic content with no Andean ferns and gymnosperms representatives. All together, this suggests a cratonic origin for this Middle Miocene fluvial paleosystem, which was probably born in the Purus Arch eastern flank and areas surrounding the crystalline. The palynological analysis results presented herein are the first direct and unequivocal evidence of the occurrence of Middle Miocene deposits in the central part of the Amazonas Basin. They also provide new perspectives for intra- and interbasin correlations, as well as paleogeographic and paleoenvironmental interpretations for the later deposition stages in the northern Brazilian sedimentary basins.

  7. Forestry Expansion during the Last Decades in the Paraiba do Sul Basin - Brazil

    NASA Astrophysics Data System (ADS)

    Carriello, F.; Rezende, F. S.; Neves, O. M. S.; Rodriguez, D. A.

    2016-06-01

    from 1986 to 2010. In this region is situated the most important and largest extension of reminiscent of Mata Atlântica Biome reminiscent. This biome has been one the most exploited Brazilian biome since 1500, when Brazilian colonization begun. To achieve this goal, we use the GIS "SPRING" and images from Landsat 5 Satellite, TM sensor from 1986, 1990, 1995, 2000, 2005 and 2010, distributed by the Brazilian National Institute for Space Research - INPE. The non-supervised-classification was applied to images in order to produce land use and land cover maps. After that, we intersect each classification for each date with the precedent date, so we can analyze the paths of each land use change, focusing forestry expansion in native's Mata Atlântica areas. The results show that eucalyptus plantations in the region have expanded mostly over fragments of Mata Atlântica. About 99.389 hectares of Mata Atlântica were transformed into forestry in 25 years, an average rate of 4000 ha per year. Clear-cut was largest between 1990 and 1995, when 22810 hectares of rain forest were cut, and between 1995 and 2000, when 21430 hectares were cut.

  8. A new species of Hisonotus (Siluriformes, Loricariidae) from rio São Francisco basin, Brazil

    PubMed Central

    Roxo, Fábio F.; Silva, Gabriel S. C.; Oliveira, Claudio

    2015-01-01

    Abstract A new species of Hisonotus is described from the rio São Francisco basin. The new species can be distinguished from congeners by having (1) a unique coloration pattern of caudal fin with one black spot extending from its origin to the ventral lobe and two dark spots at the end of the lobe’s rays; (2) odontodes forming longitudinally aligned rows on head and trunk; (3) a functional V-shaped spinelet; (4) a single rostral plate at the tip of the snout; (5) by lacking contrasting dark geometric spots on the anterodorsal region of the body; (6) a lower caudal-peduncle depth; and (7) lower counts of the lateral median plates and (8) higher premaxillary and dentary teeth. The new species is the second described species of the genus Hisonotus in the rio São Francisco basin. It was found inhabiting the marginal vegetation of the rio São Francisco and three of its tributary, rio das Velhas, rio Paraopeba and rio Formoso. PMID:25931967

  9. Dinosaur ichnofauna of the Upper Jurassic/Lower Cretaceous of the Paraná Basin (Brazil and Uruguay)

    NASA Astrophysics Data System (ADS)

    Francischini, H.; Dentzien–Dias, P. C.; Fernandes, M. A.; Schultz, C. L.

    2015-11-01

    Upper Jurassic and Lower Cretaceous sedimentary layers are represented in the Brazilian Paraná Basin by the fluvio-aeolian Guará Formation and the Botucatu Formation palaeoerg, respectively, overlapped by the volcanic Serra Geral Formation. In Uruguay, the corresponding sedimentary units are named Batoví and Rivera Members (both from the Tacuarembó Formation), and the lava flows constitute the Arapey Formation (also in Paraná Basin). Despite the lack of body fossils in the mentioned Brazilian formations, Guará/Batoví dinosaur fauna is composed of theropod, ornithopod and wide-gauge sauropod tracks and isolated footprints, as well as theropod teeth. In turn, the Botucatu/Rivera dinosaur fauna is represented by theropod and ornithopod ichnofossils smaller than those from the underlying units. The analysis of these dinosaur ichnological records and comparisons with other global Mesozoic ichnofauna indicates that there is a size reduction in dinosaur fauna in the more arid Botucatu/Rivera environment, which is dominated by aeolian dunes. The absence of sauropod trackways in the Botucatu Sandstone fits with the increasingly arid conditions because it is difficult for heavy animals to walk on sandy dunes, as well as to obtain the required amount of food resources. This comparison between the Upper Jurassic and Lower Cretaceous dinosaur fauna in south Brazil and Uruguay demonstrates the influence of aridization on the size of animals occupying each habitat.

  10. Erosion rates and landscape evolution of the lowlands of the Upper Paraguay river basin (Brazil) from cosmogenic 10Be

    NASA Astrophysics Data System (ADS)

    Pupim, Fabiano do Nascimento; Bierman, Paul R.; Assine, Mario Luis; Rood, Dylan H.; Silva, Aguinaldo; Merino, Eder Renato

    2015-04-01

    The importance of Earth's low sloping areas in regard to global erosion and sediment fluxes has been widely and vigorously debated. It is a crucial area of research to elucidate geologically meaningful rates of land-surface change and thus the speed of element cycling on Earth. However, there are large portions of Earth where erosion rates have not been well or extensively measured, for example, the tropical lowlands. The Cuiabana lowlands are an extensive low-altitude and low-relief dissected metamorphic terrain situated in the Upper Paraguay river basin, central-west Brazil. Besides exposures of highly variable dissected metamorphic rocks, flat residual lateritic caps related to a Late Cenozoic planation surface dominate interfluves of the Cuiabana lowlands. The timescale over which the lowlands evolved and the planation surface developed, and the rate at which they have been modified by erosion, are poorly known. Here, we present measurements of in situ produced cosmogenic 10Be in outcropping metamorphic bedrock and clastic-lateritic caps to quantify rates of erosion of the surface and associated landforms in order to better understand the Quaternary landscape evolution of these lowlands. Overall, slow erosion rates (mean 10 m/Ma) suggest a stable tectonic environment in these lowlands. Erosion rates vary widely between different lithologies (range 0.57 to 28.3 m/Ma) consistent with differential erosion driving regional landform evolution. The lowest erosion rates are associated with the low-relief area (irregular plains), where clastic-laterite (mean 0.67 m/Ma) and quartzite (mean 2.6 m/Ma) crop out, whereas the highest erosion rates are associated with dissection of residual hills, dominated by metasandstone (mean 11.6 m/Ma) and phyllite (mean 27.6 m/Ma). These data imply that the Cuiabana lowland is comprised of two dominant landform sets with distinct and different dynamics. Because the planation surface (mostly lowlands) is lowering and losing mass more slowly than associated residual hills, regional relief is decreasing over time and the landscape is not in steady state. The extremely slow erosion rates of the clastic-laterite are similar to the slowest outcrop erosion rates reported worldwide. These slow rates are due to the material's properties and resistance, being comprised of quartzite fragments cemented by an iron-rich crust, and reflecting long-term weathering with iron chemical precipitation and ferricrete formation, at least since the Middle Pleistocene. The lateritic caprock appears to be a key factor maintaining hilltop summits of the planation surface over long timescales.

  11. Stratigraphy and reservoir potential of glacial deposits of the Itarare Group (Carboniferous-Permian), Parana basin, Brazil

    SciTech Connect

    Franca, A.B. ); Potter, P.E. )

    1991-01-01

    Drilling in the Parana basin of Brazil in the mid-1980s discovered gas and condensate in the Itarare Group, and showed that glacial deposits in Brazil can contain hydrocarbons. The reservoir potential of the Carboniferous-Permian Itarare Group of the basin is analyzed using new subsurface data from 20 deep wells drilled in the early to middle 1980s. Central to the analysis was the construction of over 3000 km of cross sections based on more than 100 wells, the description of more than 400 m of core, and study of 95 thin sections. Subsurface exploration and mapping of the Itarare are greatly aided by the recognition of three recently defined and described formations and four members, which are traceable for hundreds of kilometers. These units belong to three major glacial cycles in which the pebbly mudstones and shales are seals and glacially related sandstones are reservoirs. The best sandstone reservoirs in the deep subsurface belong to the Rio Segredo Member, the upper-most sandy unit of the Itarare. The Rio Segredo Member is the best petroleum target because it is overlain by thick seals and massive pebbly mudstones and shales, and because it is shallower and less compacted than underlying, more deeply buried sandstones. This member has little detrital matrix and much of its porosity is secondary, developed by carboxylic acid and CO{sub 2} generated when Jurassic-Cretaceous basalts, sills, and dikes were intruded into the Parana basin as Gondwana broke up.

  12. Leaiid conchostracans from the uppermost Permian strata of the Paraná Basin, Brazil: Chronostratigraphic and paleobiogeographic implications

    NASA Astrophysics Data System (ADS)

    Ferreira-Oliveira, Luis Gustavo; Rohn, Rosemarie

    2010-03-01

    Conchostracan fossils are abundant and relatively diversified in the Rio do Rasto Formation (Passa Dois Group, Paraná Basin, southern Brazil), but leaiids (' Leaia pruvosti' [Reed, F.R.C., 1929. Novos Phyllopodos Fósseis do Brasil. Boletim do Serviço Geológico e Mineralógico do Brasil 34, 2-16]) were previously found at only one locality of the formation in the northern Santa Catarina State. New specimens of the Family Leaiidae, collected from two outcrops in central Paraná State near the top of the formation, stimulated a revision of related taxa. Both the new and the previously known leaiids are herein assigned to Hemicycloleaia mitchelli [Etheridge Jr., R., 1892. On Leaia mitchelli Etheridge. Proceedings of the Linnean Society of New South Wales 7, 307-310] based on the presence of three carinae and subovate shape. This species was originally recorded in the upper Tatarian (Wuchiapingian, Late Permian) of Sydney Basin, eastern Australia and therefore corroborates the interpretation that the leaiid bearing strata of the Rio do Rasto Formation cannot be younger than Permian. H. mitchelli possibly was one of the most widespread, eurytopic and conservative Late Paleozoic conchostracans of Gondwana (although records from Africa, India and Antarctica must still be confirmed) and it was also found in the Tatarian of Russia. The sudden disappearance of leaiids after their apparent success is consistent with the hypothesis about the biotic crisis around the Permo-Triassic boundary.

  13. Hydro-Economic Modeling with Minimum Data Requirements: An Application to the São Francisco River Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Torres, M.; Maneta, M.; Vosti, S.; Wallender, W.; Howitt, R.

    2008-12-01

    Policymakers have been charged with the efficient, equitable, and sustainable use of water resources of the São Francisco River Basin (SFRB), Brazil, and also with the promotion of economic growth and the reduction of poverty within the basin. To date, policymakers lack scientific evidence on the potential consequences for growth, poverty alleviation or environmental sustainability of alternative uses of water resources. To address these key knowledge gaps, we have linked a hydrologic and an economic model of agriculture to investigate how economic decisions affect available water, and vice versa. More specifically, the models are used to predict the effects of the application of Brazilian federal surface water use policies on farmer's net revenues and on the hydrologic system. The Economic Model of Agriculture. A spatially explicit, farm-level model capable of accommodating a broad array of farm sizes and farm/farmer characteristics is developed and used to predict the effects of alternative water policies and neighbors' water use patterns on crop mix choice. A production function comprised of seven categories of non-water-related inputs used in agriculture (land, fertilizers, pesticides, seeds, hired labor, family labor and machinery) and four water-related inputs used in agriculture (applied water, irrigation labor, irrigation capital and energy) is estimated. The parameters emerging from this estimated production function are then introduced into a non-linear, net revenue maximization positive mathematical programming algorithm that is used for simulations. The Hydrological Model. MIKE Basin, a semi-distributed hydrology model, is used to calculate water budgets for the SFRB. MIKE Basin calculates discharge at selected nodes by accumulating runoff down the river network; it simulates reservoirs using stage-area-storage and downstream release rule curves. The data used to run the model are discharge to calculate local runoff, precipitation, reference ET, crop coefficients to calculate adjusted transpiration, and reservoir operating rules. Linking the Hydro and Economic Models. Based on the crop mix and area under plow of a reference year the economic model of agriculture was calibrated. Following a Monte Carlo procedure, the statistical distribution of water flows was estimated at each of the 16 selected nodes in the SFRB. The 5th and 95th percentiles of that distribution were used as benchmarks of water availability for drought and wet years, respectively. After subtracting 2000 m3 s-1 reserved for downstream uses estimates of water availability are used as constraints in the net revenue maximization algorithm included in the model of agriculture economics. If water is binding, it will influence crop mix, area under plow and product mix choices. Results. The application of the Brazilian federal water use policies will have immediate and substantial effects on agricultural area and product mix. Agricultural incomes will fall, especially in downstream areas located near major river channels.

  14. Biophysical indicators based on satellite images in an irrigated area at the São Francisco River Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Leivas, Janice F.; Teixeira, Antônio Heriberto C.; Bayma-Silva, Gustavo; Ronquim, Carlos Cesar; Ribeiro da Silva Reis, João. Batista

    2016-10-01

    The Jaíba Irrigated Perimeter is a large irrigated agriculture area, located in the region Forest Jaíba between the São Francisco and Verde Grande rivers, in the Brazilian semi-arid region. In 2014, irrigators this the region face losses in the interruption of new plantings in irrigated areas due to water scarcity. The objective of this study is combine the model to estimate the Monteith BIO with the SAFER algorithm in the case of obtaining ET, to analyze the dynamics of natural vegetation and irrigated crops in water scarcity period. For application of the model are necessary data from meteorological stations and satellite images. Were used 23 satellite images of MODIS with spatial resolution of 250m and temporal 16 days, of 2014 year. For analyze the results, we used central pivots irrigation mask of Minas Gerais state, Brazil. In areas with irrigated agriculture with central pivot, the mean values of BIO over the year 2014 were 88.96 kg.ha-1.d-1. The highest values occurred between April 23 and May 8, with BIO 139 kg.ha-1.d-1. For areas with natural vegetation, the average BIO was 88.34 kg.ha-1.d-1 with lower values in September. Estimates of ET varied with the lowest values of ET observed in natural vegetation 1.91+/-1.22 mm.d-1 and the highest values in irrigated area is observed 3.51+/-0.97 mm.d-1. Results of this study can assist in monitoring of river basins, contributing to the management irrigated agriculture, with the trend of scarcity of water resources and increasing conflicts for the water use.

  15. The role of environmental land use conflicts in soil fertility: A study on the Uberaba River basin, Brazil.

    PubMed

    Valera, C A; Valle Junior, R F; Varandas, S G P; Sanches Fernandes, L F; Pacheco, F A L

    2016-08-15

    In the Uberaba River basin (state of Minas Gerais, Brazil), pastures for livestock production have invaded areas of native vegetation (Cerrado biome), while already existing pastures were invaded by crop agriculture, with an expansion of sugar cane plantations in the most recent years. In some areas of the basin, these land use changes were classified as environmental land use conflicts because the new uses were not conforming to land capability, i.e. the soil's natural use. Where the areas in conflict became dense, some soil properties have changed significantly, namely the organic matter content and the exchangeable potassium concentration, which have decreased drastically (5kg/m(3) per 10% increase in the conflict area) threatening the fertility of soil. Besides, these changes may have triggered a cascade of other environmental damages, specifically the increase of soil erosion and the degradation of water quality with negative impacts on aquatic biodiversity, related to a disruption of soil organic matter structural functions. Because half the Uberaba catchment has been considered is a state of accentuated environmental degradation, not only caused by environmental land use conflicts, conservation measures have been proposed and requested for immediate implementation across the watershed.

  16. Compositional variability of mixed oils and measures of sources and migration pathways: Case studies from the Potiguar basin, Brazil

    SciTech Connect

    Trindade, L.A.F. Petrobras Brassell, S.C. ); Santos Neto, E.V. )

    1991-03-01

    Regional studies of petroleum samples in cross sections from both offshore and onshore reservoirs reveal compositional differences attributable to varying extents of oil mixing with discernible landward trends. These discrepancies can be related to a combination of petroleum source, maturity, and migration history. The source rocks of these petroleum source, maturity, and migration history. The source rocks of these petroleums are classified in two groups on the basis of their geochemical and molecular characteristics: (1) Neocomian and Aptian lacustrine freshwater shales and (2) Aptian marine evaporitic shales and marls. Both families of source rocks are located in an offshore structural low. The geochemically contrasting oils derived from these source beds migrated updip through Aptian carrier beds to immature strata, constrained by a monoclinal structure. Evaluation of the distribution of compositional heterogeneities and investigation of migration effects on oil composition revealed trends related to the amount of mixing that reflect the timing of oil generation and migration and the direction of migration. The more migrated oils contain greater contributions from freshwater sources whereas the less migrated oils display increasing contributions from the shallower hypersaline source beds. Biomarker maturity parameters indicate that the most migrated oils are less mature, consistent with their early generation from the deeper lacustrine freshwater source beds and migration to first fill the shallower reservoirs.

  17. A new angiosperm from the Crato Formation (Araripe Basin, Brazil) and comments on the Early Cretaceous monocotyledons.

    PubMed

    De Lima, Flaviana J; Saraiva, Antônio A F; Da Silva, Maria A P; Bantim, Renan A M; Sayão, Juliana M

    2014-12-01

    The Crato Formation paleoflora is one of the few equatorial floras of the Early Cretaceous. It is diverse, with many angiosperms, especially representatives of the clades magnoliids, monocotyledons and eudicots, which confirms the assumption that angiosperm diversity during the last part of the Early Cretaceous was reasonably high. The morphology of a new fossil monocot is studied and compared to all other Smilacaceae genus, especially in the venation. Cratosmilax jacksoni gen. et sp. nov. can be related to the Smilacaceae family, becoming the oldest record of the family so far. Cratosmilax jacksoni is a single mesophilic leaf with entire margins, ovate shape, with acute apex and base, four venation orders and main acrodromous veins. It is the first terrestrial monocot described for the Crato Formation, monocots were previously described for the same formation, and are considered aquatics. Cratosmilax jacksoni is the first fossil record of Smilacaceae in Brazil, and the oldest record of this family.

  18. Pareiorhaphis vetula, a new armored catfish from the headwaters of the Rio Doce basin, Brazil (Siluriformes: Loricariidae).

    PubMed

    Pereira, Edson H L; Lehmann, Pablo A; Reis, Roberto E

    2016-07-28

    A new species of Pareiorhaphis is described from the upper Rio Doce basin. The description is based on a series of specimens recently collected in small headwater tributaries to the Rio Guanhães, a tributary of the Rio Santo Antonio, left bank of the Rio Doce in Minas Gerais State, eastern Brazil. Pareiorhaphis vetula, new species, is a small loricariid catfish with dark brown spots irregularly scattered over a brown background on the dorsal surface of body and along flanks. The new species differs from all other Pareiorhaphis species by having the maxillary barbel completely adnate to the lower lip and by adult males possessing a particularly elongate, sharply pointed, conical urogenital papilla. In addition, Pareiorhaphis vetula is further distinguished from most congeners by having a shorter pelvic-fin spine, or by possessing more numerous premaxillary teeth, and by lacking a dorsal-fin spinelet. A comparison with congeners P. nasuta, P. scutula and P. proskynita, which also occur in headwater streams of the Rio Doce basin is also presented.

  19. Continuous Mantle Exhumation at the Outer Continental Margin of the Santos, Campos and Espírito Santo Basins, Brazil

    NASA Astrophysics Data System (ADS)

    Zalan, P. V.; Severino, M. G.; Rigoti, C. A.; Magnavita, L. P.; Oliveira, J. B.; Viana, A. R.

    2011-12-01

    The interpretation of 12,000 km of very deep (PSTM to 16 sec., PSDM to 25 km) 2D seismic sections, coupled with gravimetric and magnetometric modeling line-by-line, and the integration of the results with the regional data bank of Petrobras, all together viewed in terms of the recent tectonic models developed for the rupturing and separation of mega-plates, led to a regional (500,000 km2), first-time ever, 3D-view of the deep structure underlying the prolific sedimentary basins of Santos, Campos and Espírito Santo in southeastern Brazil. The three basins are situated onto a continental margin that narrows gradually, from south to north, from a very wide (Santos), through an intermediate (Campos), and then to a narrow (Espírito Santo) passive margin. The seismic sections shows very well the dual rheological behavior of the continental crust, consisting of a deeper and plastic lower crust (with numerous short and strong reflections that display sub-horizontal ductile flow) and a shallower and brittle upper crust (represented by a mostly transparent and faulted seismic facies topped by the sedimentary sections of the rift and thermal subsidence phases). The crustal structure of the Santos Basin shows a zonation from west to east of alternating bands of NE-SW-trending thin (plastic basement terrains) and thick (resistant basement terrains) stretched continental crust. In vertical section this zonation is displayed as a series of necking zones, leading to a highly irregular, low to moderate crustal taper. Such zonation is less developed in the Campos Basin, where the crustal taper is moderate and regular, and practically non-existent in the Espírito Santo Basin, where the crustal taper is high. The most outstanding crustal feature shared in common by the three basins is the exhumation of mantle between the tip of the hyper-extended continental crust and the tabular-shaped oceanic crust. Although the crustal taper varies significantly from basin to basin their continental crust pinches out invariably on the flanks of exhumed mantle. This gives rise to a remarkable long (900 km along a N-S direction and 600 km in E-W direction), relatively narrow (15 to 70 km wide) and continuous belt of exhumed mantle that marks the passage from continental crust to oceanic crust in all three basins. The Santos, Campos and Espírito Santo Basins thus form a typical magma-poor passive margin. These are in sharp contrast with the adjacent basin to the south, the Pelotas Basin, that in turn is a typical volcanic passive margin displaying a long (1000 km in a N-S direction) and wide (100 to 220 km) belt of seaward-dipping reflectors at its outer margin and no exhumation of the mantle at the continent-ocean boundary.

  20. Seismites in continental sand sea deposits of the Late Cretaceous Caiuá Desert, Bauru Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Fernandes, Luiz Alberto; de Castro, Alice Bonatto; Basilici, Giorgio

    2007-07-01

    Two large-scale sediment deformation structures, minor fold occurrences in cross-bedded sand dune deposits and complex convolute folds, are observed in red sandstones, in a zone about 1.5 km long in floodway cuts at the Sérgio Motta/Porto Primavera dam, São Paulo state, Brazil. The most important structures are confined to planar zones, up to 10 m thick, in undeformed dune foreset strata were they can be traced laterally for about 50-60 m. The sandstones are part of the Rio Paraná Formation, Caiuá Group, which accumulated in a great sand sea of about 100,000 km 2. The Caiuá Desert developed during the Late Cretaceous in the southern part of the Bauru Basin, an intracontinental subsiding area in the central-southern part of the South-American Platform. The basin was filled by a sandy sequence about 300 m thick. The sand sea deposits correspond to the Caiuá Group and comprise: a) deposits of dry sand sheets (Santo Anastácio Formation), b) deposits of medium-sized dunes and humid interdunes of the sand sea peripheral zones (Goio Erê Formation), and c) deposits of large-sized complex aeolian dunes and draas, that correspond to the central part of the inland sand sea (Rio Paraná Formation). The deformations in the sediments are attributed to the effects of fluidization, liquefaction and shear stress, which are interpreted as being earthquake-induced structures, mainly because: (1) the deformed horizons are confined between undeformed cross-bedded strata, (2) the complex convolute folds sometimes include nappe-like structures that overlie foreset facies, (3) during the Bauru Basin infilling there was tectonic activity associated with alkaline volcanism on the borders of the basin and related silicification in the central-southern part. The main silicification zones are aligned to regional lineaments that cross the area near the large-scale sedimentary deformation structures.

  1. Geochemistry of Central Atlantic Magmatic Province (CAMP) sills from deep boreholes in the Amazonas and Solimões basins, Brazil

    NASA Astrophysics Data System (ADS)

    Hatlen Heimdal, Thea; Svensen, Henrik H.; Pereira, Egberto; Planke, Sverre

    2016-04-01

    The Central Atlantic Magmatic Province (CAMP) is one of the most extensive Large Igneous Provinces (LIPs), and is associated with the breakup of Pangea and the subsequent opening of the central Atlantic Ocean. A large part of the province, including > 1 M km2 basins containing sill intrusions, is located in Brazil but has received limited attention due to the lack of outcrops. We have studied CAMP sills from seven deep boreholes (up to 3100 m deep) in the Amazonas and Solimões basins, northern Brazil. The boreholes contain up to ~ 482 m of sills (18 % of the stratigraphy), with a maximum individual sill thickness of 140 m. The sills were partly emplaced into thick Carboniferous evaporites. The main mineral phases of the sills include plagioclase and pyroxene, with accessory apatite, biotite, ilmenite and quartz. The majority of the sills are low-Ti dolerites (TiO2 < 2 wt.%), with the exception of four samples (with 2.2 - 3.3 wt.% TiO2). The low-Ti rocks range from basalt to basaltic andesite and plot in the tholeiitic field defined within the total alkali versus silica (TAS) classification. C1 chondrite normalized Rare Earth Element (REE) patterns for both Ti-groups show increasing LREE compared to HREE (La/Lu = 2.2 - 4.1) with no major anomalies, and attest to a relatively evolved nature (La = 17-65 ppm). Primitive mantle normalized patterns for low-Ti rocks show negative anomalies for Nb, Ta, P and Ti and positive for K, whereas the high-Ti rocks show generally opposite anomalies. Late stage patches in the dolerites contain apatite, quartz and Cl-bearing biotite, suggesting the presence of halogens that may partly derive from the host sedimentary rocks.

  2. Stratigraphy and facies analysis of the Cenomanian Turonian boundary succession in the Japaratuba area, Sergipe Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Walter, Simone; Herrmann, Achim D.; Bengtson, Peter

    2005-08-01

    A facies analysis of the Cenomanian-Turonian (Cretaceous) boundary beds was carried out in the Japaratuba area, Sergipe Basin, north-eastern Brazil, on the basis of seven outcrop sections. The lower part of the succession is represented by dolomitic limestones and marly limestones, whereas the upper part is dominated by chalky, nodular limestones and bedded and coquinoid limestones. Three microfacies types are recognized in the upper part of the succession, where biostratigraphic work has indicated the position of the Cenomanian-Turonian boundary. Two of these microfacies types (foraminiferal mudstone, wackestone) occur only in the nodular limestone unit and are referred to an outer carbonate ramp setting. The uppermost part of the succession is dominated by echinoderm-inoceramid packstones, which probably were deposited in a mid-ramp setting. In the late Cenomanian, deposition took place in the outer-ramp distal area of an open-marine basin, which gradually became shallower during the Cenomanian-Turonian transition, as evidenced by the increase in macrofaunal debris to the northeast. In addition to macrofossil fragments, some thin sections contain abundant planktic and benthic foraminifers, calcispheres, and roveacrinids; the latter are potentially useful for stratigraphic purposes. Biostratigraphic data suggest that the lowermost Turonian is missing in the southern part of the Japaratuba area.

  3. The ichthyofauna of drifting macrophyte mats in the Ivinhema River, upper Paraná River basin, Brazil

    USGS Publications Warehouse

    Bulla, C. K.; Gomes, Luiz Carlos; Miranda, Leandro E.; Agostinho, A. A.

    2011-01-01

    We describe the fish assemblages associated with drifting macrophyte mats and consider their possible role as dispersal vectors in the Ivinhema River, a major tributary of the upper Paraná River, Brazil. Fish associated with drifting mats were sampled in the main river channel during January and March 2005, when the wind and/or the increased water level were sufficient to transport macrophyte stands. Fish in the drifting mats were sampled with a floating sieve (4 m long x 2 m wide x 0.6 m high, and 2 mm mesh size). In the laboratory, larvae, juvenile, and adult fish were counted and identified to the lowest possible taxonomic level. In four drifting macrophyte mats we captured 218 individuals belonging to at least 28 species, 17 families, and 6 orders. Aphyocharax dentatus, Serrasalmus spp., and Trachelyopterus galeatus were the most abundant taxa associated with the mats, but species richness ranged from 6 to 24 species per mat. In addition, 85% of the total number of individuals caught was larvae and juveniles. Although preliminary and based on limited samples, this study of drifting macrophyte mats was the first one in the last unregulated stretch of the Paraná River remaining inside Brazilian territory, and alerts us to the potential role of macrophytes mats as dispersers of fish species in the region.

  4. XX/XO, a rare sex chromosome system in Potamotrygon freshwater stingray from the Amazon Basin, Brazil.

    PubMed

    de Souza Valentim, Francisco Carlos; Porto, Jorge Ivan Rebelo; Bertollo, Luiz Antonio Carlos; Gross, Maria Claudia; Feldberg, Eliana

    2013-09-01

    Potamotrygonidae is a representative family of South American freshwater elasmobranchs. Cytogenetic studies were performed in a Potamotrygon species from the middle Negro River, Amazonas, Brazil, here named as Potamotrygon sp. C. Mitotic and meiotic chromosomes were analyzed using conventional staining techniques, C-banding, and detection of the nucleolus organizing regions (NOR) with Silver nitrate (Ag-NOR). The diploid number was distinct between sexes, with males having 2n = 67 chromosomes, karyotype formula 19m + 8sm + 10st + 30a, and fundamental number (FN) = 104, and females having 2n = 68 chromosomes, karyotype formula 20m + 8sm + 10st + 30a, and FN = 106. A large chromosome, corresponding to pair number two in the female karyotype, was missing in the male complement. Male meiotic cells had 33 bivalents plus a large univalent chromosome in metaphase I, and n = 33 and n = 34 chromosomes in metaphase II. These characteristics are consistent with a sex chromosome system of the XX/XO type. Several Ag-NOR sites were identified in both male and female karyotypes. Positive C-banding was located only in the centromeric regions of the chromosomes. This sex chromosome system, which rarely occurs in fish, is now being described for the first time among the freshwater rays of the Amazon basin.

  5. New petrified forest in Maranhão, Permian (Cisuralian) of the Parnaíba Basin, Brazil

    NASA Astrophysics Data System (ADS)

    da Conceição, Domingas Maria; de Andrade, Luiz Saturnino; Cisneros, Juan Carlos; Iannuzzi, Roberto; Pereira, Agostinha Araújo; Machado, Francisco Carlos

    2016-10-01

    This work presents a new fossil plant-bearing area located in the municipalities of Duque Bacelar and Coelho Neto, Maranhão State, Brazil, recovered from lower Permian (Cisuralian) strata of the Pedra de Fogo Formation, northeastern portion of the Parnaíba Basin. The area comprises more than five exposures with assemblages formed mostly of large gymnosperm woods, a number of them in life-position (reaching up to ∼2.30 m in height and 1.15 m in diameter) and, in lesser degree, of horizontal tree-fern stems (up to 5 m in length), some of them being referable to Psaronius sp. The fossils are recorded in sedimentary beds of continental origin that accumulated in shallow, nearshore areas of large lakes, which eventually were affected by rapid burial episodes generated by non-channelized, high energy fluvial systems. The new fossil assemblages are included within lacustrine rocks placed at the base of the Pedra de Fogo Formation, i.e., Sílex Basal Member, near the contact with the underlying Piauí Formation (Pennsylvanian). This observation contrasts with previous studies at the southwestern portion of the basin, where the stratigraphic position of plant fossils is referred to the upper Pedra de Fogo Formation (Trisidela Member) or even to the overlying Motuca Formation. The new sites currently suffer damage from human activities and require urgent actions in order to protect them. Based on the current laws, some measures of protection for these sites are discussed and proposed herein. xml:lang="pt"

  6. Effect of seasonal flooding cycle on litterfall production in alluvial rainforest on the middle Xingu River (Amazon basin, Brazil).

    PubMed

    Camargo, M; Giarrizzo, T; Jesus, A J S

    2015-08-01

    The assumption for this study was that litterfall in floodplain environments of the middle Xingu river follows a pattern of seasonal variation. According to this view, litterfall production (total and fractions) was estimated in four alluvial rainforest sites on the middle Xingu River over an annual cycle, and examined the effect of seasonal flooding cycle. The sites included two marginal flooded forests of insular lakes (Ilha Grande and Pimentel) and two flooded forests on the banks of the Xingu itself (Boa Esperança and Arroz Cru). Total litterfall correlated with rainfall and river levels, but whereas the leaf and fruit fractions followed this general pattern, the flower fraction presented an inverse pattern, peaking in the dry season. The litterfall patterns recorded in the present study were consistent with those recorded at other Amazonian sites, and in some other tropical ecosystems.

  7. Chain of commercialization of Podocnemis spp. turtles (Testudines: Podocnemididae) in the Purus River, Amazon basin, Brazil: current status and perspectives

    PubMed Central

    2014-01-01

    Background Consumption of turtles by natives and settlers in the Amazon and Orinoco has been widely studied in scientific communities. Accepted cultural customs and the local dietary and monetary needs need to be taken into account in conservation programs, and when implementing federal laws related to consumption and fishing methods. This study was conducted around the Purus River, a region known for the consumption and illegal trade of turtles. The objective of this study was to quantify the illegal turtle trade in Tapauá and to understand its effect on the local economy. Methods This study was conducted in the municipality of Tapauá in the state of Amazonas, Brazil. To estimate turtle consumption, interviews were conducted over 2 consecutive years (2006 and 2007) in urban areas and isolated communities. The experimental design was randomized with respect to type of household. To study the turtle fishery and trade chain, we used snowball sampling methodology. Results During our study period, 100% of respondents reported consuming at least three species of turtles (Podocnemis spp.). Our estimates indicate that about 34 tons of animals are consumed annually in Tapauá along the margins of a major fishing river in the Amazon. At least five components related to the chain of commercialization of turtles on the Purus River are identified: Indigenous Apurinã and (2) residents of bordering villages (communities); (3) of local smugglers buy and sell turtles to the community in exchange for manufactured goods, and (4) regional smugglers buy in Tapauá, Lábrea, and Beruri to sell in Manaus and Manacapuru; Finally, (5) there are professional fishermen. Conclusions We quantify the full impact of turtle consumption and advocate the conservation of the region’s turtle populations. The Brazilian government should initiate a new turtle consumption management program which involves the opinions of consumers. With these measures the conservation of freshwater turtles in the Brazilian Amazon, is possible. PMID:24467796

  8. Geology and taphonomy of the base of the Taquaral Member, Irati Formation (Permian, Paraná Basin), Brazil

    NASA Astrophysics Data System (ADS)

    Chahud, Artur; Petri, Setembrino

    2015-09-01

    The taphonomy of Early Permian vertebrates from a sandy facies at the base of the Taquaral Member, Irati Formation, was surveyed in order to acquire data for the interpretation of the sedimentary processes and paleoenvironment of deposition. Six outcrops from the Rio Claro municipality and surrounding areas, from the Brazilian State of São Paulo, were investigated. The vertebrate groups are Chondrichthyes (Xenacanthiformes, Ctenacanthiformes and Petalodontiformes), Osteichthyes (Actinopterygii and Sarcopterygii) and Tetrapodomorpha. They occur as loose teeth, scales, spines and bone remains. The sandy facies is characterized by fining upward deposition. The coarser sandstone immediately above the underlying Tatuí Formation is rich in Chondrichthyes. However, the fine sandstone above, immediately beneath the silty shale facies, is devoid of Chondrichthyes, though Osteichthyes scales, teeth and bones were present. The taphonomy is important for inferring sedimentary processes and then the paleoenvironments. The poor sorting of the sandstone and the presence of fossils that are mostly abraded or worn are indicative of a high energy environment. In contrast, the presence of fossils in a good state of preservation, some without abrasion and breakages are indicative of only limited transport. Differences of fossil spatial density, numbers of specimens and taxa may be explained by the dynamics of deposition, from details of the palaeoenvironment can be obtained.

  9. New insights into Gondwana paleography based on palinological data from Morro do Chaves Formation (Sergipe-Alagoas Basin, Brazil)

    NASA Astrophysics Data System (ADS)

    Gonçalves Garcia, Gustavo; Vasconcellos Garcia, Antônio Jorge; Henriques, Maria Helena

    2016-04-01

    The Sergipe-Alagoas basin (NE Brazil) has been widely studied in the frame of oil exploration, because it displays the most complete exposition of the stratigraphic sequences from the basins of the Brazilian continental margin. In this context, the aim of this workis to present the results of the bio-stratigraphic and paleo-environmental analysis of Morro do Chaves Formation (Lower Cretaceous), in Alagoas Sub-basin, part of the transitional section situated between the rift phase and restricted marine environment associated with the South Atlantic ocean opening. The material was analyzed from the palynological point of view and was collected in the InterCement quarry, located in São Miguel dos Campos, State of Alagoas. From 17 outcrop rock samples collected, nine had palynological content; among these only six were considered for biostratigraphic analysis purposes. In addition to outcrop samples, 28 samples were processed from four core drill. The paleoenvironmental analysis was based on the palynological content of the collected samples and on the paleontological and geological information available. The studied sedimentary package corresponds to carbonate and fine siliciclastic deposits, with approximately 70.0 m in thickness. The unit in question is formed by carbonatic "coquinóides" rocks interspersed with shale levels of dark green color. Palinofloristic assemblages were recuperated between 5.0 m and 70.0 m of the outcropping section. In the recovered material it was possible to identify 9 kinds of spores and 8 kinds of pollen grains, and two genera of fungi. Due to the degree of preservation of the material, age was established by the occurrence of Dicheiropollis etruscus specimens, which has enabled the recognition of the Dicheiropollis etruscus palinozone (upper Barremian). In microscopic observations under fluorescent light some algalic vesicles components were also recognized and classified as possible algae of the Prasinophyceae class, indicating predominantly marine environment, which together with the identification of organisms classified as Scenedesmus sp., allows the recognition of an aquatic environment. Moreover, the occurrence of a palinoforaminifer specimen in a sample strengthens the argument of the marine characterrelated to these deposits. The amorphous organic matter present in the analyzed material shows high degree of fluorescence at some levels, which usually results of marine algal degradation. These results support a first attempt to paleoenvironmental and paleogeographic reconstruction for Morro do Chaves Formation. The occurrence of marine elements in these Neocomian intervals, together with previous paleontological data, can be related to the input of "Tethyan waters", coming from the Mid-Atlantic regionto the Gondwanic continental crust through half grabens,which have acted as "sea ways".

  10. New field evidence for silicic ignimbrites and proximal lavas and their distribution in the Parana Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Tramontano, S.; Harmon, L. J.; Gravley, D. M.; Gualda, G. A. R.

    2014-12-01

    Silicic ignimbrites and lavas are sometimes very difficult to distinguish from one another in the field. Their accurate identification provides the basis for a better understanding of the origin of these deposits, including processes related to magma extraction, fragmentation and eruption style. We are studying the silicic volcanics in the Paraná Rift Basin in southern Brazil (the ~130 to 135 Ma Palmas member of the Serra Geral Formation), the counterpart to the Etendeka silicic volcanics in Africa. We present new field evidence for the identification of tabular-shaped ignimbrite-like packages, which contrast with dome-shaped proximal viscous lavas and domes. The tabular-shaped packages are highly welded and devitrified, but primary feldspar and pyroxene crystals can still be identified in outcrops. Flow/cooling unit boundaries can be seen at outcrop scale as well as at the kilometer scale where successive flat-topped terraces have been cut into the volcanic landscape. These packages bear conspicuous swarms of vesicle-poor black lens-shaped features set in a light colored matrix. The lenses range in their aspect ratio (2D height vs. length) and can be > 2 m long. Horizontal jointing is superimposed on the black lens-bearing outcrops and their spacing appears to coincide with the aspect ratio of the lenses, i.e. thinner lenses have a narrower joint spacing. Locally wider lenses grade down into completely stretched and/or flattened lenses that resemble conventional flow banding. We interpret these tabular packages as ignimbrites and the vesicle-poor black lenses as juvenile magma blobs (distinct from typical pumice or fiamme). A notably different flow-banded, irregularly deformed, and sometimes obsidian-bearing lithology appears in a number of locations. It supports topography characterized by rolling hills that contrasts markedly with the tilted plateaus supported by ignimbrites. The difference in morphology between ignimbrites and lavas is most readily observed in the north-south trending southern Brazil escarpment, where up to ~700 m of tabular-shaped packages are juxtaposed against domical features. Future work will include detailing the genetic relationships between these two different lithologies, as well as the study of the magmatic conditions that led to their eruption.

  11. Silviculture of eucaliptus plantations in the Paraiba do Sul basin, Brazil, and its potential implication on the basin ecohydrology.

    NASA Astrophysics Data System (ADS)

    Carriello, Felix; Andres Rodriguez, Daniel; Marques Neves, Otto; Vicens, Raul

    2014-05-01

    Silviculture of eucaliptus plantations is an important driver of the Mata Atlântica biome conversion into another land use in the Paraíba do Sul basin, in the southeastern of Brazil. This region is located in one of the most developed areas in Brazil, between Rio de Janeiro and São Paulo, the most important cities in Brazil, linked by Presidente Dutra highway. Between both cities there are another cities that produce a variety of goods - from meat to planes, cars and mobile phones. This area is, at the same time, one the most important hot spot for the Mata Atlântica biome. Here we have a large Mata Atlântica fragment protected by law and others fragments being conversed to pasture, agriculture, silviculture and urban areas. Paraiba do Sul river drains the region and runs into Rio de Janeiro State. The basin is highly anthropized, with multiple approaches of its waters resources. Its waters also serve Rio de Janeiro metropolitan area. Because land use and land cover changes impact the water yield in a basin, the study of its dynamic its of great importance for water resources management. We study the land use and land cover change in the region between 1986 and 2010, focusing in the development of silviculture of eucaliptus plantations. We used the HAND (Height Above Nearest Drainage) approach that uses the height above the nearest water body, acquired from SRTM Data and transformed into a Terrain Numeric Mode, to classify the landscape into three different ecohydrological environments: floodplain, mountain top and hillslope. This classes were intersected with 1986 and 2010 land use and cover change classification obtained from Landsat imagery. Results show that silviculture has increased in the region from 1986 to 2010. In both years, silviculture areas are mainly located at the hillslope (47%), while floodplain and mountain top share 28 % and 23 % respectively. Available census data from the Brazilian Institute of Geography and Statistics, IBGE, for 1995 and 2006 years, show an increment in the number of small farmers, from 27 to 196, that are planting eucalyptus sp in the region and also an increase in the whole silvicuture production. Silviculture of eucaliptus plantations is recognized to be a great water consuming and a driver of water pollution by pesticides and fertilizers. The study carried out combines a landscape descriptor with land use and land cover changes mapping to provide an important database for ecohydrological studies, regarding the water resources management.

  12. Reproductive seasonality of fishes from a lotic stretch of the Grande River, high Paraná river basin, Brazil.

    PubMed

    Andrade, P M; Braga, F M S

    2005-08-01

    We searched for correlations between water level, rainfall, temperature, and reproductive activity of fishes in a lotic stretch of the Grande River below the Volta Grande Dam. Gillnets were used to catch the fish on six field journeys made bimonthly between April 1998 and February 1999. Fish gonads were classified according to maturation grade and the amount of mature or spent gonads was correlated with rainfall and air temperature. Most fish species showed seasonal reproduction (between October and February). The relative frequency of fully mature and spent gonads significantly correlated with rainfall (Spearman r = 0.94, p = 0.005) and air temperature (r = 0.84, p = 0.036), showing the importance of these factors in regulating the reproductive cycle of fishes in this location. Nevertheless, dam operation resulted in minimal water level variation that did not significantly correlate with reproductive activity (r = -0.43, p = 0.396).

  13. Shallow lacustrine system of the Permian Pedra de Fogo Formation, Western Gondwana, Parnaíba Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Araújo, Raphael Neto; Nogueira, Afonso César Rodrigues; Bandeira, José; Angélica, Rômulo Simões

    2016-04-01

    The Permian Period of the Parnaíba Basin, northern Brazil, represented here by deposits from the Pedra de Fogo Formation, records important events that occurred in Western Gondwana near its boundary with the Mesozoic Era. The analysis of outcrop based facies from the Permian Pedra de Fogo Formation, which is 100 m thick, carried out along the eastern and western borders of the Parnaiba Basin, allowed the identification of eleven sedimentary facies, which were grouped into three distinct facies associations (FA), representative of a shallow lacustrine system associated with mudflats and ephemeral rivers. Bioturbation, desiccation cracks, silcretes and various siliceous concretions characterize the Pedra de Fogo deposits. The FA1 mudflat deposits occur predominantly at the base of the Pedra de Fogo Formation and consist of laminated claystone/mudstone, mudcrack-bearing sandstones/mudstones and sandstones exhibiting cross-lamination, massive and megaripple bedding. Popcorn-like silicified nodules and casts indicate evaporite deposits. Other common features are silica concretions, silicified tepees and silcretes. FA2 represents nearshore deposits and consists of fine-grained sandstones with evenly parallel lamination, climbing ripple cross-lamination, massive and megaripple bedding and mudstone/siltstone showing evenly parallel lamination. FA3 refers to wadi/inundite deposits, generally organized as fining-upward cycles of metric size, composed of conglomerates and medium-grained pebbly sandstones showing massive bedding and cross-stratification, as well as claystone/siltstone showing evenly parallel to undulate lamination. Scour-and-fill features are isolated in predominantly tabular deposits composed of mudstones interbedded with fine to medium-grained sandstones showing planar to slightly undulate lamination. Silicified plant remains previously classified as belonging to the Psaronius genus found in the uppermost levels of the Pedra de Fogo Formation, near the contact with the Motuca Formation, are considered here as excellent biostratigraphic markers. Fish remains, ostracods, bryozoans and scolecodonts represent other fossils that are present in the succession. Mudflat deposits developed in an arid and hot climate probably in the Early Permian. Semi-arid conditions prevailed in the Middle Permian allowing the proliferation of fauna and flora in adjacent humid regions and onto the lake margin. The climate variation was responsible for the contraction and expansion phases of the lake, fed by sporadic sheet floods carrying plant remains. The reestablishment of the arid climate, at the end of Permian, marks the final sedimentation of the Pedra de Fogo Formation, linked to the consolidation of the Pangaea Supercontinent. This last event was concomitant with the deposition of the Motuca Formation red beds and the development of extensive ergs related to the Triassic Sambaíba Formation in Western Gondwana.

  14. Allozyme relationships in hypostomines (Teleostei: Loricariidae) from the Itaipu Reservoir, Upper Rio Paraná basin, Brazil.

    PubMed

    Zawadzki, Cláudio Henrique; Renesto, Erasmo; dos Reis, Roberto Esser; Moura, Maurício Osvaldo; Mateus, Rogério Pincela

    2005-03-01

    In an allozyme electrophoresis survey of 15 hypostomine species from the Itaipu Hydroelectric Reservoir, 25 loci from 14 enzyme systems were scored. Allozyme data allowed recording diagnostic genetic markers for all species analyzed and for some species groups within Hypostomus, a taxon which is taxonomically still unresolved in the Upper Rio Paraná basin. The mean expected heterozygosity of the species was considerably variable and hypotheses to tentatively explain this variation are discussed. A cladogram based upon the allelic frequencies of the species analyzed was produced by the continuous maximum likelihood method: Rhinelepis aspera and M. parananus were separated from the species of Hypostominae by a long branch length. Pterygoplichthys anisitsi was the sister of all the representatives of the genus Hypostomus. Within Hypostomus, two main clades were produced: in the first, H. cochliodon was the sister of the species comprising the H. plecostomus group, and in the second, the tree showed the following relationships: (H. albopunctatus (H. regani + Hypostomus sp. 3) + (H. margaritifer (H. microstomus (Hypostomus sp. 1 (H. ternetzi + Hypostomus sp. 2)). Hypostomus ternetzi and Hypostomus sp. 2 are referred to here as representatives of the H. ternetzi group.

  15. Hisonotus acuen, a new and phenotypically variable cascudinho (Siluriformes, Loricariidae, Hypoptopomatinae) from the upper rio Xingu basin, Brazil

    PubMed Central

    Silva, Gabriel S. C.; Roxo, Fábio F.; Oliveira, Claudio

    2014-01-01

    Abstract A new species of Hisonotus is described from the headwaters of the rio Xingu. The new species is distinguished from its congeners by having a functional V-shaped spinelet, odontodes not forming longitudinal aligned rows on the head and trunk, lower counts of the lateral and median series of abdominal figs, presence of a single rostral fig at the tip of the snout, absence of the unpaired figlets at typical adipose fin position, yellowish-tipped teeth, absence of conspicuous dark saddles and stripe on the body and higher number of teeth on the premaxillary and dentary. The new species, Hisonotus acuen, is restricted to headwaters of the rio Xingu basin, and is the first species of the genus Hisonotus described from the rio Xingu basin. Hisonotus acuen is highly variable in aspects of external body proportions, including body depth, snout length, and abdomen length. This variation is partly distributed within and among populations, and is not strongly correlated with body size. PCA of 83 adult specimens from six allopatric populations indicates the presence of continuous variation. Therefore, the available morphological data suggest that the individuals inhabiting the six localities of rio Xingu represent different populations of a single species. Low intraspecific variation in mitochondrial Cytochrome oxidase subunit I (COI) provides corroborative evidence. PMID:25349492

  16. A new "Bat-Voiced" species of Dendropsophus Fitzinger, 1843 (Anura, Hylidae) from the Amazon Basin, Brazil.

    PubMed

    Orrico, Victor G D; Peloso, Pedro L V; Sturaro, Marcelo J; Da Silva-Filho, Heriberto F; Neckel-Oliveira, Selvino; Gordo, Marcelo; Faivovich, Julián; Haddad, Célio F B

    2014-11-06

    We describe Dendropsophus ozzyi sp. nov., a new species of treefrog, tentatively included in the Dendropsophus microcephalus Group and most notably diagnosed by the presence of pointed fingers and an advertisement call with a very high dominant frequency. The new species is known from three localities in the Brazilian Amazon forest, two on western State of Pará and one (the type locality) in eastern State of Amazonas (03°56'50"S and 58°26'36"W, 45 m a.s.l.).

  17. Birth Control

    MedlinePlus

    ... girlshealth.gov/ Home Body Your sexuality Birth control Birth control Birth control (also called contraception) may seem confusing ... more. What do I need to know about birth control? top The more you know about birth control, ...

  18. Dream controller

    DOEpatents

    Cheng, George Shu-Xing; Mulkey, Steven L; Wang, Qiang; Chow, Andrew J

    2013-11-26

    A method and apparatus for intelligently controlling continuous process variables. A Dream Controller comprises an Intelligent Engine mechanism and a number of Model-Free Adaptive (MFA) controllers, each of which is suitable to control a process with specific behaviors. The Intelligent Engine can automatically select the appropriate MFA controller and its parameters so that the Dream Controller can be easily used by people with limited control experience and those who do not have the time to commission, tune, and maintain automatic controllers.

  19. Depositional systems in the lower Cretaceous Morro Do Chaves and Coqueiro Seco formations, and their relationship to petroleum accumulations, middle rift sequence, Sergipe-Alagoas Basin, Brazil

    SciTech Connect

    de Figueiredo, A.M.F.

    1981-01-01

    In the Sergipe-Alagoas Basin, northeast coast of Brazil, the Lower Cretaceous lacustrine, middle rift sequence is composed of the Morro do Chaves and Coqueiro Seco Formations. Subsurface analysis permitted recognition and mapping of four principal types of depositional environments: Morro do Chaves carbonate platform, and Coqueiro Seco fluvial-deltaic, fan delta, and slope systems. Morro do Chaves lacustrine carbonate sediments were deposited in positive areas flanking the principal point sources (rivers), and are composed of high energy limestones. Contemporaneous deep-water euxinic and bituminous lacustrine shales were deposited under starved basin conditions. Sublacustrine canyon excavation attested to the presence of a destructional slope episode. Coqueiro Seco fluvial-deltaic and fan delta facies display high sand/shale ratios and blocky to massive E-log patterns; slope facies display serrate to digitate E-log patterns and is less sandy. Delta plain channel-fill facies and coarse-grained meanderbelt fluvial facies are dominant in fluvial-deltaic systems of the Alagoas Sub-basin; and proximal to medial conglomerates and coarse conglomeratic sandstones are dominant facies in fan delta systems of the Rio Sao Francisco Sub-basin. Slope facies are composed of sublacustrine fans formed by fine- to medium-grained sandstones enveloped by subbituminous shales, and lacustrine limestones. Coqueiro Seco coarse clastic systems prograded across the basin and buried Morro do Chaves carbonate platforms in response to cyclic tectonic pulses related to rift development. Evaluation of petroleum occurrences in relationship to defined depositional systems permitted recognition of several types of plays characterized by unique structural and stratigraphic relationships exhibited by reservoirs, source beds and structure. The Coqueiro Seco slope play, formed by updip pinchout of turbidite fans, is judged the most promising in the sequence.

  20. Characterization of environmental quality of forest fragments changes in Jundiaí-Mirim river basin-Brazil using the Markov Chain model

    NASA Astrophysics Data System (ADS)

    Hasimoto Fengler, Felipe; Leite de Moraes, Jener Fernando; Irio Ribeiro, Admilson; Peche Filho, Afonso; Araujo de Medeiros, Gerson; Baldin Damame, Desirée; Márcia Longo, Regina

    2015-04-01

    In Brazil is common practice the concurrency of large urban centers water catchment in distant sites. There's no policy to preserve strategic springs in the urban territory. Thus, rural areas, located in the surrounds of municipals, usually provide water and others environment services to the population that reside on cities. The Jundiaí-Mirim river basin, located in the most urbanized state in Brazil, São Paulo, composes an interesting example of this situation. It is located in a rural area near large urban centers, with large industrial parks, near the capital of state. As result of expansion of the cities on its surrounds their lands have had a historic of monetary valorization, making its territories attractive to the housing market. Consequently, the region has an intense process of urbanization that resulted in an increasing environmental disturbance in the areas of natural vegetation. In the other hand, the watershed is the principal water supplier of Jundiaí city, and houses forest remaining of an important Biome in Brazil, the Atlantic Rain Forest. Given the need to preserve its water production capacity and the forest remnants there, this study modeled the environmental quality of forest fragments through indicators of disturbance and evaluated the changes that occur between 1972 and 2013 using the Markov Chain model. The environment quality was determined by nine indicators of environmental disturbance (distance of urban areas, roads, edge land use, size, distance of others forest fragments, land capacity of use, watershed forest cover, number of forest fragments in the watersheds, shape of the forest fragment), obtained by techniques of Geoprocessing, and integrated by Multicriteria Analysis. The Markov Chain model showed a constant tendency of deteriorating in natural vegetation environmental quality, attributed to the intense process of occupation of the river basin. The results showed a historical trend of transformation in forest fragments with very low environmental quality to others uses and a static behavior of forest fragments with high environmental quality. It was explained by the tendency of occupation in forest fragments near urban areas, roads, with small size and high perturbation, and difficulties in occupation of forest fragments with high size, isolated from urban areas end roads. It was concluded that: (a) urbanization and deforestation of natural vegetation were primarily responsible for changes in environmental quality; (b) there is a need to create public policies to preserve the natural vegetation in the Jundiaí-Mirim river basin.

  1. Impact assessment of the introduction of Cichla kelberi in a large Neotropical reservoir and its lateral lagoons (Upper Paraná River Basin, Brazil).

    PubMed

    Ferrareze, M; Nogueira, M G

    2015-11-10

    AbstractThis study aimed to understand how the introduction of Cichla kelberi in Rosana Reservoir (Paranapanema River) affected the native ichthyofauna. Data on the structure of the small fish fauna assemblage were obtained before and after the introduction of this carnivorous species. Samplings were carried out in February and September of 2004, previously to the register of Cichla kelberi in the reservoir, and after its introduction, November of 2004, January, March, May and August of 2005, February and June of 2006, February and July of 2007, February and October of 2008 and February of 2009. A total of 4,693 fish, belonging to 43 different species was sampled between 2004 and 2009. The order Characiformes was the most abundant, followed by Perciformes and Siluriformes. Comparative analyses, before and after the introduction, could not demonstrate significant changes in composition, richness, abundance, biomass, mean length and diversity of fish. Aquatic insects were the main feeding item of C. kelberi, followed by tetragonopterinae fish. Cannibalism was recorded during the whole study period. The results showed that Cichla cannot deeply affect the ichthyofauna assemblages of a large Neotropical reservoir, at least in a short or medium term period after its introduction. The results also allowed concluding that the introduction of C. kelberi in the reservoir is in the phase 3. In this phase, the specie can survive and reproduce in the new environment; however it is not totally established and disseminated. The reasons for the fact that Cichla is still not dominant in Rosana Reservoir could be related to feeding competition, high rate of cannibalism and the presence of large amount of aquatic macrophytes (refuge zones). In spite of the results, the continuous monitoring of the role of non-native species on the local fish fauna is absolutely necessary because the impacts caused by colonization of this undesirable species can be magnified by complex processes, usually correlated with other environmental disturb, especially the negative effects of damming.

  2. Impact assessment of the introduction of Cichla kelberi in a large Neotropical reservoir and its lateral lagoons (Upper Paraná River Basin, Brazil).

    PubMed

    Ferrareze, M; Nogueira, M G

    2015-11-01

    This study aimed to understand how the introduction of Cichla kelberi in Rosana Reservoir (Paranapanema River) affected the native ichthyofauna. Data on the structure of the small fish fauna assemblage were obtained before and after the introduction of this carnivorous species. Samplings were carried out in February and September of 2004, previously to the register of Cichla kelberi in the reservoir, and after its introduction, November of 2004, January, March, May and August of 2005, February and June of 2006, February and July of 2007, February and October of 2008 and February of 2009. A total of 4,693 fish, belonging to 43 different species was sampled between 2004 and 2009. The order Characiformes was the most abundant, followed by Perciformes and Siluriformes. Comparative analyses, before and after the introduction, could not demonstrate significant changes in composition, richness, abundance, biomass, mean length and diversity of fish. Aquatic insects were the main feeding item of C. kelberi, followed by tetragonopterinae fish. Cannibalism was recorded during the whole study period. The results showed that Cichla cannot deeply affect the ichthyofauna assemblages of a large Neotropical reservoir, at least in a short or medium term period after its introduction. The results also allowed concluding that the introduction of C. kelberi in the reservoir is in the phase 3. In this phase, the specie can survive and reproduce in the new environment; however it is not totally established and disseminated. The reasons for the fact that Cichla is still not dominant in Rosana Reservoir could be related to feeding competition, high rate of cannibalism and the presence of large amount of aquatic macrophytes (refuge zones). In spite of the results, the continuous monitoring of the role of non-native species on the local fish fauna is absolutely necessary because the impacts caused by colonization of this undesirable species can be magnified by complex processes, usually correlated with other environmental disturb, especially the negative effects of damming.

  3. Allozyme comparison of two populations of Rineloricaria (Siluriformes, Loricariidae) from the Ivaí River, upper Paraná River basin, Brazil

    PubMed Central

    2009-01-01

    Two allopatric morphotypes of the genus Rinelocaria were compared through the allozyme electrophoresis technique: one morphotype, R. pentamaculata, from the Keller River in the middle stretch of the Ivaí River basin and the other, R. aff. pentamaculata, from the São João River in the upper portion of the Ivaí River basin. The morphotype from the São João River was collected upstream from the São João waterfall, which is about 80 m deep. Twelve enzymatic systems (AAT, ADH, EST, GCDH, G3PDH, GPI, IDH, LDH, MDH, ME, PGM and SOD) were analyzed, which allowed to score 22 loci. Only lociAat-2, Est-3 and Mdh-C showed polymorphism. The two samples differed in allele frequencies at the three polymorphic loci. The average expected heterozygosity for all loci was 0.0806 ± 0.0447 in the Keller River sample. For the São João River morphotype, this value was 0.0489 ± 0.0350. Nei' s genetic identity and distance between the two populations were respectively 0.9789 and 0.0213. Wright's FIS , FIT and FST over all loci were estimated as 0.3121, 0.4021 and 0.1309, respectively. We consider that the two morphotypes represent species in statunascendi. PMID:21637702

  4. Biochemical comparison of two Hypostomus populations (Siluriformes, Loricariidae) from the Atlântico Stream of the upper Paraná River basin, Brazil

    PubMed Central

    2009-01-01

    Two syntopic morphotypes of the genus Hypostomus - H. nigromaculatus and H. cf. nigromaculatus (Atlântico Stream, Paraná State) - were compared through the allozyme electrophoresis technique. Twelve enzymatic systems (AAT, ADH, EST, GCDH, G3PDH, GPI, IDH, LDH, MDH, ME, PGM and SOD) were analyzed, attributing the score of 20 loci, with a total of 30 alleles. Six loci were diagnostic (Aat-2, Gcdh-1, Gpi-A, Idh-1, Ldh-A and Mdh-A), indicating the presence of interjacent reproductive isolation. The occurrence of few polymorphic loci acknowledge two morphotypes, with heterozygosity values He = 0.0291 for H. nigromaculatus and He = 0.0346 for H. cf. nigromaculatus. FIS statistics demonstrated fixation of the alleles in the two morphotypes. Genetic identity (I) and distance (D) of Nei (1978) values were I = 0.6515 and D = 0.4285. The data indicate that these two morphotypes from the Atlântico Stream belong to different species. PMID:21637646

  5. A new species of Ituglanis from the Rio Xingu Basin, Brazil, and the evolution of pelvic fin loss in trichomycterid catfishes (Teleostei: Siluriformes: Trichomycteridae).

    PubMed

    Datovo, Aléssio

    2014-04-22

    A new species of the trichomycterid catfish genus Ituglanis is described from the Rio Curuá, Rio Xingu basin, Rio Amazonas drainage, Brazil. Ituglanis apteryx, new species, is promptly distinguished from congeners, except some specimens of I. parahybae (Eigenmann), by the absence of pelvic fins, girdle, and muscles. The new species differs from I. parahybae in the pattern of the cephalic laterosensory system; the absence of a posterior cranial fontanel; the presence of an epural; and the number of branchiostegal rays, ribs, and vertebrae. Ituglanis apteryx is one among the several trichomycterids lacking pelvic fins. Analysis reveals that pelvic fin loss independently evolved several times during the trichomycterid radiation.

  6. Effect of environmental quality and mesohabitat structure on a Biotic Integrity Index based on fish assemblages of cerrado streams from Rio Cuiabá basin, Brazil.

    PubMed

    Machado, Ng; Venticinque, Em; Penha, J

    2011-08-01

    Over the last 30 years, the Cerrado has been experiencing various antropic impacts that have brought about alterations to species composition, structure and functioning of aquatic habitats. Therefore, studies on negative impacts are useful to prevent future damage and restore environmental quality. The objectives of our study were: i) to adapt an index of biotic integrity of streams in the Rio Cuiabá Basin and ii) to analyze if the Index of Biotic Integrity (IBI) correlated with the environmental quality measured by the Index of Environmental Quality (IEQ) and with the mesohabitat structure. We sampled 26 streams in sub-basins of the Cuiabá River. In each stream, we closed a stretch of 50 m with blockage nets and used electrofishing to capture fish. To obtain a measure of environmental quality in sampled units, we characterized the stream and its micro basin. For the analyses, we used the Spearman Correlation, Kruskal-Wallis test and Analysis of Multiple Regression. We collected 697 individuals distributed into 6 orders, 15 families and 49 species. The IBI followed changes on environmental quality measured by IEQ when we removed streams that present natural barriers from the analysis (r² = 0.4; r² = 0.58). Types of land use did not affect the biotic integrity (n = 26; df = 4; H = 4,860; p = 0.302), but natural and artificial barriers affected it (n = 26; df = 4; H = 11,027; p = 0.026). The IBI was not sensitive to variations in mesohabitat structure (F₂,₂₃ = 0.373; r² = 0.031; Axe 1 p = 0.620; Axe 2 p = 0.490). The IBI is certainly a reasonable instrument for evaluating changes in the environment, but we cannot ignore the fact that we were able to obtain the same result with any combinations of metrics. This makes its analysis and interpretation difficult.

  7. Survey for foot-and-mouth disease in the endangered marsh deer (Blastocerus dichotomus) from marshlands of the Parana River Basin, Brazil.

    PubMed

    Araújo, João Pessoa; Nogueira, Márcia F; Duarte, José M B

    2010-07-01

    Habitat fragmentation and diseases have resulted in a decline of the marsh deer (Blastocerus dichotomus) throughout its South American range. Our objectives were to determine whether marsh deer intended for translocation from a region of the Rio Paraná Basin had been infected previously by foot-and-mouth disease virus (FMDV) and whether they were carrying virus. We captured marsh deer from June to October 1998 and collected blood from 108 animals and esophageal-pharyngeal fluid from 53. Serum was tested for antibodies against three FMDV serotypes (O, A, and C) by liquid-phase-blocking sandwich enzyme-linked immunosorbent assay (ELISA). Esophageal-pharyngeal fluid was tested for FMDV RNA by reverse transcription polymerase chain reaction (RT-PCR) and inoculation into three successive baby hamster kidney (BHK-21) cell subcultures, followed by RT-PCR of cultures. We detected low log(10) titers (range 1.0-1.5) to FMDV subtype A(24) Cruzeiro in 19 of 108 sampled marsh deer, but failed to isolate FMDV or detect FMDV RNA in any samples. We conclude that marsh deer from our study site were unlikely to carry FMDV; however, as a preventive measure, the 19 animals with titers for FMDV were not sent to FMDV-free Brazilian states.

  8. High-Resolution Zircon U-Pb CA-TIMS Dating of the Carboniferous—Permian Successions, Paraná Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Griffis, N. P.; Mundil, R.; Montanez, I. P.; Isbell, J.; Fedorchuk, N.; Lopes, R.; Vesely, F.; Iannuzzi, R.

    2015-12-01

    The late Paleozoic Ice Age (LPIA) is Earth's only record of a CO2-forced climatic transition from an icehouse to greenhouse state in a vegetated world. Despite a refined framework of Gondwanan ice distribution, questions remain about the timing, volume, and synchronicity of high-latitude continental ice and the subsequent deglaciation. These questions ultimately preclude our understanding of linkages between ice volume, sea level, and high- and low-latitude climate. Poor constraints on the timing and synchronicity of glacial and interglacial transitions reflect a lack of high-resolution radioisotopic dates from high-latitude, ice-proximal Carboniferous-Permian successions. The Rio Bonito Fm in Rio Grande do Sul State of southern Brazil hosts the oldest non-glaciogenic Carboniferous- Permian deposits of the Paraná Basin, thus recording the icehouse-to-greenhouse transition. Despite a widespread effort over the last two decades to constrain these deposits in time by means of U-Pb zircon geochronology, published data sets of the Candiota and Faxinal coals of the Rio Bonito Fm host discrepancies that may reflect post- eruptive open system behavior of zircon and analytical artifacts. These discrepancies have hindered the correlation of the Candiota and Faxinal sediments within the larger Gondwanan framework. Here we present the first U-Pb ages on closed system single zircons using CA-TIMS techniques on Permo-Carboniferous ash deposits of the Paraná Basin. Preliminary results indicate two major and distinct coal-forming periods that are separated by ca 10 Ma. Our results and conclusions are not in agreement with multi- crystal U-Pb TIMS and SIMS ages that suggest coeval deposition of the Candiota and Faxinal coals. CA-TIMS analyses applied to zircons from additional ash deposits are aimed at constructing a robust chronostratigraphic framework for the Carboniferous- Permian succession of the Paraná Basin, which will facilitate a better understanding of the timing and ice dynamics of the LPIA.

  9. A new side-neck turtle (Pelomedusoides: Bothremydidae) from the Early Paleocene (Danian) Maria Farinha Formation, Paraíba Basin, Brazil.

    PubMed

    Carvalho, Anny Rafaela De Araújo; Ghilardi, Aline Marcele; Barreto, Alcina Magnólia Franca

    2016-06-21

    Limestone and marl from Maria Farinha Formation (Paraíba Basin, NE Brazil) accumulated in a shallow continental shelf environment during the expansion of the Atlantic Ocean in early Paleocene (Danian). It contains a rich paleontological record, which comprises many marine invertebrates, several species of bony and cartilaginous fishes, a crocodyliform and turtle remains. Here, we describe a new genus and species of pleurodire turtle from Maria Farinha Formation, based on a nearly complete plastron, an incomplete left pelvic girdle, and four dermal plates of the carapace. We tested the phylogenetic position of Inaechelys pernambucensis gen. et sp. nov. by including it in a comprehensive cladistic analysis of pleurodires. The new species is included within Botrhemydidae, with affinities to Bothremydini, positioned as sister group of Rosasia soutoi. Inaechelys pernambucensis gen. et sp. nov. differs from R. soutoi for the almost straight anterior lobe cranial edge of its plastron, as well as for its pentagonal shaped entoplastron and its abdominal shield midline, which is considerably smaller than the respective femoral shield midline. Inaechelys pernambucensis is the first turtle species formally described from Brazilian Paleocene strata. Within Bothremydidae, it is also the first conclusively fully marine species described for this country. This new record contributes to the understanding of the ecology and paleobiogeographical distribution of Bothremydidae family.

  10. Infrastructure sufficiency in meeting water demand under climate-induced socio-hydrological transition in the urbanizing Capibaribe River Basin - Brazil

    NASA Astrophysics Data System (ADS)

    Ribeiro Neto, A.; Scott, C. A.; Lima, E. A.; Montenegro, S. M. G. L.; Cirilo, J. A.

    2014-03-01

    Water availability for a range of human uses will increasingly be affected by climate change especially in the arid and semi-arid tropics. This paper aims to evaluate the ability of reservoirs and related infrastructure to meet targets for water supply in the Capibaribe River Basin (CRB), in the state of Pernambuco, Brazil. The basin has experienced spatial and sectoral (agriculture-urban) reconfiguration of water demands. Human settlements that were once dispersed, relying on intermittent sources of surface water, are now increasingly experiencing water-scarcity effects. As a result, rural populations in the CRB are concentrating around infrastructural water supplies in a socio-hydrological transition process that results from (a) hydroclimatic variability, (b) investment and assistance programs that may enhance but can also supplant local adaptive capacity, and (c) demographic trends driving urbanization of the state capital, Recife, which mirror urban growth across Brazil. In the CRB, demands are currently composed of 69.1% urban potable water, 14.3% industrial, 16.6% irrigation (with ecosystem-service demands met by residual flow). Based on the application of linked hydrologic and water-resources models using precipitation and temperature projections of the IPCC SRES A1B scenario, a reduction in rainfall of 31.8% translated to streamflow reduction of 67.4% under present reservoir operations rules. The increasing demand due to population was also taken into account. This would entail severe water supply reductions for human consumption (-45.3%) and irrigation (-78.0%) by the end of the 21st century. This study demonstrates the vulnerabilities of the infrastructure system during socio-hydrological transition in response to hydroclimatic and demand variabilities in the CRB and also indicates the differential spatial impacts and vulnerability of multiple uses of water to changes over time. The paper concludes with a discussion of the broader implications of climate change, urbanization, and industrialization for water supply under socio-hydrological conditions of scarcity.

  11. Conodont biostratigraphy and paleoecology of the marine sequence of the Tapajós Group, Early-Middle Pennsylvanian of Amazonas Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Scomazzon, Ana Karina; Moutinho, Luciane Profs; Nascimento, Sara; Lemos, Valesca Brasil; Matsuda, Nilo Siguehiko

    2016-01-01

    This study was undertaken in the south and western regions of the Amazonas Basin to describe the conodont biostratigraphy and paleoecology of Pennsylvanian carbonate rocks of the marine portion of the Tapajós Group comprising the upper Monte Alegre, Itaituba, and lower Nova Olinda formations. The analyzed area includes one outcrop along the Tapajós river (TAP), two carbonate quarries (QI, QII), and 18 wells (dots 1-18). The conodont fauna is dominated by Idiognathoides sinuatus and Neognathodus symmetricus in the Monte Alegre Formation, followed by Idiognathodus incurvus, Diplognathodus coloradoensis and Neognathodus bassleri in the Itaituba and Nova Olinda formations. The conodont association suggests an Early to Middle Pennsylvanian age to the analyzed section. Relative ages attributed to the three lithostratigraphic units using conodonts, palynomorphs, and foraminifers are consistent. Herein are proposed one local taxon-range zone of Idiognathodus incurvus in the Itaituba and lower part of the Nova Olinda Formation and one local taxon-range subzone of Diplognathodus coloradoensis in the Itaituba Formation, suggesting a late Bashkirian - Moscovian (Atokan - early Desmoinesian) age to these strata. The Itaituba Formation marks the establishment of large Pennsylvanian marine conditions in the Amazonas Basin and is composed primarily of marine carbonates of abundant fossil content, tidal flat evaporites and siliciclastic thin intervals. Its lower limit, with the Monte Alegre Formation, is characterized by the predominant occurrence of fluvial-deltaic sandstones superimposed on an extensive sequence of aeolian sandstones, siltstones and shales intercalated with the interdune and lakes. From the upper strata of Itaituba Formation the faunal and lithological characteristics indicate the occurrence of a regressive phase culminating in a restricted environment, arid which indicates the Nova Olinda Formation. This is characterized by the occurrence of evaporites increasingly abundant to the top of carbonates, also shales and siltstones intercalated with the sabkha plain. The carbonate strata have similar marine fossils to those of Itaituba Formation, however, the fauna becomes impoverished in abundance and diversity. The conodont fauna of Early-Middle Pennsylvanian of Amazonas Basin suggests similarities of species with the North American Midcontinent region and the Illinois Basin indicating their probable cosmopolitism; however in a slightly different paleogeographic context, probably due to latitudinal differences, coal deposits are present in North America, whereas widespread evaporitic deposits are registered to the Tapajós Group, Amazonas Basin.

  12. Paleobiology of a unique vertebrate coprolites concentration from Rio do Rasto Formation (Middle/Upper Permian), Paraná Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Dentzien-Dias, Paula C.; de Figueiredo, Ana Emilia Q.; Horn, Bruno; Cisneros, Juan Carlos; Schultz, Cesar L.

    2012-12-01

    A large number of coprolites were collected in one outcrop in the lacustrine facies of Rio do Rasto Formation (Middle/Upper Permian) in Southern Brazil. The material ranges from 0.6 cm to 11 cm in length. Their mineralogy, inclusions and morphology were studied to infer their biological source and taphonomy. All of them contain fragments of bones and fish scales, as well as crystalline apatite, and therefore are assigned to carnivores. A wide variety of morphotypes is described, including the knots and the well-known spiral coprolites (heteropolar and amphipolar), as well as a new kind of heteropolar coprolite we called as "edge", that has the whorls grouped in the very end of one pole. These data allow us to instead that a wide variety of vertebrates lived in the lakes of the Middle/Upper Permian in southern Brazil.

  13. Palynological and sedimentary analysis of the Igarapé Ipiranga and Querru 1 outcrops of the Itapecuru Formation (Lower Cretaceous, Parnaíba Basin), Brazil

    NASA Astrophysics Data System (ADS)

    Ferreira, Neila N.; Ferreira, Elizabete P.; Ramos, Renato R. C.; Carvalho, Ismar S.

    2016-03-01

    The siliciclastic sediments of the Itapecuru Formation occur in a large area of the Parnaíba Basin and its deposits crop out along the Itapecuru River, in Maranhão State, northern Brazil. The palynological analysis of the Igarapé Ipiranga and Querru 1 outcrops strata yields a rich and diversified data. The presence of index-palynofloras in assemblages allows the identification of the Complicatisaccus cearensis Zone, of Late Aptian-Early Albian age. Terrestrial palynomorphs are abundant in the assemblages, being represented by bryophytes and pteridophytes, especially perisporate trilete spores (Crybelosporites and Perotrilites), and gymnosperms and angiosperms (Afropollis and Elaterosporites). The composition of palynological assemblages suggests the presence of moist soils for both outcrops. Acritarchs were recovered in the Querru 1 outcrop, which suggest a marine setting supporting a tidal flat environment indicated by facies associations. Furthermore, reworked Paleozoic palynomorphs were observed in the Querru 1 outcrop. The microflora from Igarapé Ipiranga outcrop suggests terrestrial environment corroborating with floodplain environment indicated by facies association.

  14. Estimation of evapotranspiration for different land covers in a Brazilian semi-arid region: A case study of the Brígida River basin, Brazil

    NASA Astrophysics Data System (ADS)

    Santos, Celso Augusto Guimarães; Silva, Richarde Marques da; Silva, Alexandro Medeiros; Brasil Neto, Reginaldo Moura

    2017-03-01

    In this study, the Surface Energy Balance Algorithm for Land (SEBAL) was used to compute the surface albedo, vegetation indices (NDVI, SAVI and LAI), surface temperature, soil heat flux and evapotranspiration (ET) over two contrasting years (dry and wet) in the Brígida River basin, a semi-arid region of north-eastern Brazil. The actual ET was computed during satellite overpass and was integrated for 24 h on a pixel-by-pixel basis for the daily ET distribution. Due to the topographic effects, an attempt was also made to incorporate DEM information to estimate the net radiation. The land cover types identified in the watershed are cropland, bare land, dense canopy, grassland, and caatinga vegetation. In order to study the variation among the biophysical parameters and ET, two-way analysis of variance (ANOVA) was used. The ET calculated by SEBAL ranged between 2.46 and 6.87 mm/day for the dry year (1990) and 1.31 and 6.84 mm/day for the wet year (2009) for the river basin. The results showed that a reduction in vegetation cover is evident in the temporal and spatial analysis over the studied periods in the region and that these facts influence the values of the energy balance and ET. The results showed significant differences in the variables of land cover type and year at the probability level of 0.05 for all land cover types.

  15. Trilobites, scolecodonts and fish remains occurrence and the depositional paleoenvironment of the upper Monte Alegre and lower Itaituba formations, Lower - Middle Pennsylvanian of the Amazonas Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Moutinho, Luciane Profs; Nascimento, Sara; Scomazzon, Ana Karina; Lemos, Valesca Brasil

    2016-12-01

    This study aims to characterize the scolecodonts, trilobite pygidium fragments and fish remains of an outcropped region in the southern Amazonas Basin, comprising the uppermost section of the Monte Alegre Formation and the basal section of the Itaituba Formation. These, correspond to part of the marine portion of the Tapajós Group, related to an intracratonic carbonate platform. The Monte Alegre Formation includes a deposition of fluvial-deltaic and aeolian sandstones, siltstones and shales of interdunes and lakes, intercalated with transgressive carbonates of a shallow restrict nearshore marine environment. The Itaituba Formation comprises a thickest deposit of marine carbonates, representing the establishment of widespread marine conditions, and is the richest interval containing organisms of shallow marine environment in the Pennsylvanian of the Amazonas Basin. The associated fauna includes brachiopods, bivalves, gastropods, crinoids, echinoids, bryozoans, corals, foraminifers, sponges, ostracods, trilobites, scolecodonts, fish remains and conodonts, mainly in the packstones, and subordinately in the wackestones and mudstones. Conodonts Neognathodus atokaensis, Diplognathodus orphanus, Idiognathodus incurvus, and foraminifers Millerella extensa, Millerella pressa, Millerella marblensis, Eostaffella ampla, Eostaffella pinguis and Eostaffella advena characterizes a predominant Atokan age to the analyzed profile. The fossil association herein presented is taxonomically diversified and biologically interesting, comprising an important and well preserved, for the first time occurrence of two molds and two fragments of Proetida trilobites. Well preserved Eunicida and Phyllodocida scolecodonts and paleonisciform fish remains. These fossils help in the paleoenvironmental establishment of the studied interval in the Amazonas Basin and as a potential biostratigraphic and paleoecological tool to correlate regionally and globally the Pennsylvanian.

  16. Geophysical evidence of pre-sag rifting and post-rifting fault reactivation in the Parnaíba basin, Brazil

    NASA Astrophysics Data System (ADS)

    Lopes de Castro, David; Hilário Bezerra, Francisco; Adolfo Fuck, Reinhardt; Vidotti, Roberta Mary

    2016-04-01

    This study investigated the rifting mechanism that preceded the prolonged subsidence of the Paleozoic Parnaíba basin in Brazil and shed light on the tectonic evolution of this large cratonic basin in the South American platform. From the analysis of aeromagnetic, aerogravity, seismic reflection and borehole data, we concluded the following: (1) large pseudo-gravity and gravity lows mimic graben structures but are associated with linear supracrustal strips in the basement. (2) Seismic data indicate that 120-200 km wide and up to 300 km long rift zones occur in other parts of the basins. These rift zones mark the early stage of the 3.5 km thick sag basin. (3) The rifting phase occurred in the early Paleozoic and had a subsidence rate of 47 m Myr-1. (4) This rifting phase was followed by a long period of sag basin subsidence at a rate of 9.5 m Myr-1 between the Silurian and the late Cretaceous, during which rift faults propagated and influenced deposition. These data interpretations support the following succession of events: (1) after the Brasiliano orogeny (740-580 Ma), brittle reactivation of ductile basement shear zones led to normal and dextral oblique-slip faulting concentrated along the Transbrasiliano Lineament, a continental-scale shear zone that marks the boundary between basement crustal blocks. (2) The post-orogenic tectonic brittle reactivation of the ductile basement shear zones led to normal faulting associated with dextral oblique-slip crustal extension. In the west, pure-shear extension induced the formation of rift zones that crosscut metamorphic foliations and shear zones within the Parnaíba block. (3) The rift faults experienced multiple reactivation phases. (4) Similar processes may have occurred in coeval basins in the Laurentia and Central African blocks of Gondwana.

  17. Taphonomy of a Baurusuchus (Crocodyliformes, Baurusuchidae) from the Adamantina Formation (Upper Cretaceous, Bauru Basin), Brazil: Implications for preservational modes, time resolution and paleoecology

    NASA Astrophysics Data System (ADS)

    Araújo Júnior, Hermínio Ismael de; Silva Marinho, Thiago da

    2013-11-01

    Upper Cretaceous vertebrate accumulations from the Adamantina Formation are known due to their high taxonomic diversity. On the other hand, taphonomic analyses still are rare, limiting the understanding of processes related to the biostratinomic and fossildiagenetic histories of this lithostratigraphic unit. In 2005, fossils were collected from an outcrop located at Jales municipality, state of São Paulo, southeastern Brazil. From this outcrop, a well-preserved Baurusuchus was recovered, which displays a peculiar set of taphonomic signatures. This paper identifies and interprets taphonomic features of a specimen of Baurusuchus (Crocodyliformes, Baurusuchidae; UFRJ DG 418-R) from the Adamantina Formation (Upper Cretaceous of the Bauru Basin), in Jales municipality, state of São Paulo. Brief taphonomic comparisons with other specimens previously studied (crocodiles and dinosaurs) and a lithofaciological analysis of the outcrop were undertaken in order to enhance the knowledge of the stratigraphy and paleoenvironment and improve the time resolution for the Adamantina Formation in the region of Jales. Furthermore, paleoecological data were interpreted based on the taphonomic analysis. The fossil is composed of an articulated segment of vertebral column, ribs, part of the pelvic girdle and gastralia. There is no hydraulic equivalence between both the specimen of Baurusuchus and the size of quartz grain predominant in the fossiliferous layer, suggesting death in situ or short transport as a “water carcass”. Teeth marks identified on the pubes were assigned to a small/juvenile baurusuchid crocodyliform or a theropod dinosaur. The repositioning of some elements (ribs and dorsal osteoderms) is suggestive of mummification. Desiccation marks were observed and attributed to the stage 1 of weathering. These features suggest subaerial exposure of the carcass prior to burial, however, probably after the mummification. On the other hand, the subaerial exposure was short, because the individual was not fully disarticulated. Furthermore, the degrees of articulation and preservation of the specimen nullify the hypothesis of reworking. Lithofaciological and taphonomic analyses suggest a well-drained floodplain as the burial environment and an arid or semi-arid climate in the region of Jales outcrop. In addition, the taphonomic signatures seem to indicate a time resolution about 100-104 years for the layer where the crocodyliforms were collected, but it seems to have, within this time limit, temporal-mixing among terrestrial crocodiles and dinosaurs collected from the same layer, suggesting time-averaging in this outcrop.

  18. Distribution of populations of broad-snouted caiman (Caiman latirostris, Daudin 1802, Alligatoridae) in the São Francisco River basin, Brazil.

    PubMed

    Filogonio, R; Assis, V B; Passos, L F; Coutinho, M E

    2010-11-01

    We surveyed populations of the broad-snouted caiman, Caiman latirostris, throughout the São Francisco River basin, from Três Marias reservoir, State of Minas Gerais, to the river delta, at the boarder of Sergipe and Alagoas states. We registered the occurrence of crocodilians in 61% of all surveyed localities (n = 64), in which the presence of C. latirostris was confirmed in 44% of the surveyed sites. Caimans occurred in both lentic and lotic habitats, although there was a preference for small dams, oxbow lakes and wetlands. Despite the hunting pressure and human impact on natural habitats, our results indicate that the populations of C. latirostris in the São Francisco basin are not fragmented.

  19. Inversion of TEM data and analysis of the 2D induced magnetic field applied to the aquifers characterization in the Paraná basin, Brazil

    NASA Astrophysics Data System (ADS)

    Realpe Campaña, Julian David; Porsani, Jorge Luís; Bortolozo, Cassiano Antonio; Serejo de Oliveira, Gabriela; Monteiro dos Santos, Fernando Acácio

    2017-03-01

    Results of a TEM profile by using the fixed-loop array and an analysis of the induced magnetic field are presented in this work performed in the northwest region of São Paulo State, Brazil, Paraná Basin. The objectives of this research were to map the sedimentary and crystalline aquifers in the area and analyzing the behavior of the magnetic field by observation of magnetic profiles. TEM measurements in the three spatial components were taken to create magnetic profiles of the induced (secondary) magnetic field. The TEM data were acquired using a fixed transmitter loop of 200 m × 200 m and a 3D coil receiver moving along a profile line of 1000 m. Magnetic profiles of dBz, dBx and dBy components showed symmetrical spatial behavior related with loop geometry. z-component showed a behavior probably related to superparamagnetic effect (SPM). dBz data was used to perform individual 1D inversion for each position and to generate an interpolated pseudo-2D geoelectric profile. The results showed two low resistivity zones: the first shallow, between 10 m and 70 m deep, probably related to the Adamantina Formation (sedimentary aquifer). The second between 200 m and 300 m depth, probably related to a fractured zone filled with water or clay inside the basalt layer of the Serra Geral Formation (crystalline aquifer). These results agree with the well logs information available in the studied region.

  20. Allozyme differentiation of two populations of the genus Neoplecostomus Eigenmann & Eigenmann, 1888 (Teleostei, Loricariidae) from the upper Paraná River basin, Brazil

    PubMed Central

    Reusing, Ana Flávia; Renesto, Erasmo; Roxo, Fábio F.; Zawadzki, Cláudio H.

    2011-01-01

    Allozyme electrophoresis was used to examine 12 enzymatic systems in two populations of the genus Neoplecostomus from the Paraná River basin. Samples of Neoplecostomus sp. 1 were collected in Paraitinguinha stream of the Tietê River basin, in the municipality of Salesópolis, São Paulo State, and those of Neoplecostomus sp. 2 from São Domingos stream of the Rio Grande River basin, in the municipality of Muzambinho, Minas Gerais State. The genetic variability of the two populations was estimated by Nei’s expected heterozygosity and was considered lower than average for populations of freshwater fish. The proportion of polymorphic loci was low (only 5.26% for the locus Idh). The low frequency of heterozygosity for both populations revealed a high fixation of alleles for each locus. Homozygote excess was observed in both populations. The values of Nei’s genetic identity and the presence of loci with different allele frequencies in both populations may imply that the two populations belong to different species. The genetic variability between populations was compared to other data for loricariids. PMID:21931525

  1. The onset of flood basalt volcanism, Northern Paraná Basin, Brazil: A precise U-Pb baddeleyite/zircon age for a Chapecó-type dacite

    NASA Astrophysics Data System (ADS)

    Janasi, Valdecir de Assis; de Freitas, Vivian Azor; Heaman, Larry H.

    2011-02-01

    We report the first U-Pb baddeleyite/zircon date for a felsic volcanic rock from the Paraná Large Igneous Province in south Brazil. The new date of 134.3 ± 0.8 Ma for a hypocrystalline Chapecó-type dacite from Ourinhos (northern Paraná basin) is an important regional time marker for the onset of flood basalt volcanism in the northern and western portion of the province. The dated dacite was erupted onto basement rocks and is overlain by a high-Ti basalt sequence, interpreted to be correlative with Pitanga basalts elsewhere. This new U-Pb date for the Ourinhos dacite is consistent with the local stratigraphy being slightly older than the few reliable step-heating 40Ar/39Ar dates currently available for overlying high-Ti basalts (133.6-131.5 Ma). This indicates an ~ 3 Ma time span for the building of the voluminous high-Ti lava sequence of the Paraná basin. On the other hand, it overlaps the 40Ar/39Ar dates (134.8-134.1 Ma) available for the stratigraphically older low-Ti basalt (Gramado + Esmeralda types) and dacite-rhyolite (Palmas type) sequences from South Brazil, which is consistent with the short-lived character of this volcanism and its rapid succession by the high-Ti sequence.

  2. Two new species of Melanorivulus (Cyprinodontiformes: Cynolebiidae) from Rio Verde drainage, Upper Rio Paraná basin, Brazil.

    PubMed

    Volcan, Matheus Vieira; Klotzel, Bruno; Lanés, Luis Esteban Krause

    2017-02-21

    Two new species of the genus Melanorivulus are herein described from the middle Rio Verde drainage, upper Rio Paraná basin, Mato Grosso do Sul, Brazil. Both new species are members of the Melanorivulus pictus clade, diagnosed by having ventral process of angulo-articular vestigial and flanks intense greenish blue or greenish golden to purplish blue above anal fin base in males. Melanorivulus nigropunctatus, new species, from wetlands of a small drainage tributary of right side of the Rio Verde, differs from all other congeners by possessing black dots over the head and body in both sexes and pectoral fin orange with a dark grey margin in males. Melanorivulus ofaie, new species, is found in a similar environment, but at the opposite margin of the Rio Verde. It is distinguished by males presenting flank greenish blue to light blue, with seven to nine oblique chevron-like red bars, ventral portion of head whitish with dark brown spots, dorsal fin yellow with two to three transverse broad red oblique stripes and distal region red, anal fin light orangish yellow, basal area light blue with short red bars and distal portion with a dark red margin, and caudal fin yellow or orangish yellow with three to four vertical red bars in the dorsal and middle portions, sometimes with a orange distal margin. Both new species are considered endangered due to the loss and degradation of their habitat.

  3. A tapinocephalid dinocephalian (Synapsida, Therapsida) from the Rio do Rasto Formation (Paraná Basin, Brazil): Taxonomic, ontogenetic and biostratigraphic considerations

    NASA Astrophysics Data System (ADS)

    Boos, A. D. S.; Kammerer, C. F.; Schultz, C. L.; Paes Neto, V. D.

    2015-11-01

    Permian tetrapod fossils have been recovered from the Rio do Rasto Formation of Brazil since the 1970s. Previous studies of this fauna indicated strong affinities with the Guadalupian-Lopingian vertebrates of South Africa and Eastern Europe, suggesting biostratigraphic correlations between these areas. Here, a new dinocephalian specimen from the Rio do Rasto Formation in the Serra do Cadeado area (Paraná State, Brazil) is described based on fragmentary skull remains and an associated left lower jaw ramus. Despite the fragmentary nature of these remains, they represent the most complete tapinocephalid specimen known from South America. Comparison with other tapinocephalids indicates that the material described herein represents a juvenile or sub-adult specimen. Although it is not possible to identify this material to the genus level, it most closely resembles the 'moschopines' Moschops and Moschognathus from the Tapinocephalus Assemblage Zone of South Africa. As dinocephalians are known to be restricted to the Guadalupian, they are one of the best tetrapod biostratigraphic markers for the Rio do Rasto Formation, indicating that at least some of the strata in the areas where they occur [Serra do Cadeado (Paraná State), Fagundes farm and Boqueirão farm (Rio Grande do Sul State)] are Guadalupian. Vertebrate fossils from Rio do Rasto Formation occur in disperse, isolated and discontinuous outcrops, so that they have been grouped in 'local faunas'. However, most of the specimens lack precise stratigraphic provenance data and even occurring in locations near each other they are not necessarily contemporary. Thus, until a more robust stratigraphic framework is developed, we suggest discontinuing use of 'local faunas' to this stratigraphic unit.

  4. Description of two new species of Hisonotus Eigenmann & Eigenmann, 1889 (Ostariophysi, Loricariidae) from the rio Paraná-Paraguay basin, Brazil

    PubMed Central

    Roxo, Fábio F.; Zawadzki, Cláudio H.; Troy, Waldo P.

    2014-01-01

    Abstract Two new species of Hisonotus are described from the rio Paraná-Paraguay basin in Brazil. The most remarkable features of the new species are the odontodes forming longitudinally aligned rows (one odontode after the other, but not necessarily forming parallel series) on the head and trunk (vs. odontodes not forming longitudinally aligned rows), a pair of rostral plates at the tip of the snout (vs. a single rostral plate), the functional v-shaped spinelet (vs. spinelet non-functional, square-shaped, or absent). These features suggest close phylogenetic relationships with Hisonotus bockmanni, H. insperatus, H. luteofrenatus and H. piracanjuba. Additionally, both new species are distinguished from their congeners by characters related to head length and depth, orbital diameter, suborbital depth, caudal peduncle depth, pectoral-fin spine length, snout length and counts of teeth. Hisonotus paresi sp. n. further differs from its congeners by having contrasting dark geometric spots on the anterodorsal region of the body, a character lacking in H. oliveirai sp. n. The variation in number and shape of the rostral plate, posterior rostrum plates, infraorbitals and the preopercle in both new species and in H. insperatus are discussed. PMID:24715789

  5. Rodent Control

    ERIC Educational Resources Information Center

    Indian Journal of Adult Education, 1975

    1975-01-01

    Strategies for rodent control in crop fields, threshing yards, and rural residential areas are presented together with an operational plan for implementing a program for rodent control at the national level. Training personnel in rodent control procedures and procedures for educating the public in the necessity for control are covered. (EC)

  6. Propulsion controls

    NASA Technical Reports Server (NTRS)

    Harkney, R. D.

    1980-01-01

    Increased system requirements and functional integration with the aircraft have placed an increased demand on control system capability and reliability. To provide these at an affordable cost and weight and because of the rapid advances in electronic technology, hydromechanical systems are being phased out in favor of digital electronic systems. The transition is expected to be orderly from electronic trimming of hydromechanical controls to full authority digital electronic control. Future propulsion system controls will be highly reliable full authority digital electronic with selected component and circuit redundancy to provide the required safety and reliability. Redundancy may include a complete backup control of a different technology for single engine applications. The propulsion control will be required to communicate rapidly with the various flight and fire control avionics as part of an integrated control concept.

  7. Restructurable Controls

    NASA Technical Reports Server (NTRS)

    Montoya, R. J. (Compiler); Howell, W. E. (Compiler); Bundick, W. T. (Compiler); Ostroff, A. J. (Compiler); Hueschen, R. M. (Compiler); Belcastro, C. M. (Compiler)

    1983-01-01

    Restructurable control system theory, robust reconfiguration for high reliability and survivability for advanced aircraft, restructurable controls problem definition and research, experimentation, system identification methods applied to aircraft, a self-repairing digital flight control system, and state-of-the-art theory application are addressed.

  8. Controlling Fertility.

    ERIC Educational Resources Information Center

    Donnay, France

    1991-01-01

    Recent developments in fertility control are presented in relation to the global demographic situation. Discussion focuses on changes in scientific knowledge and concepts that have shifted the focus from birth control to planned parenthood to the notion of controlled fertility. The place of family planning programs, including their socioeconomic…

  9. Control Software

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Real-Time Innovations, Inc. (RTI) collaborated with Ames Research Center, the Jet Propulsion Laboratory and Stanford University to leverage NASA research to produce ControlShell software. RTI is the first "graduate" of Ames Research Center's Technology Commercialization Center. The ControlShell system was used extensively on a cooperative project to enhance the capabilities of a Russian-built Marsokhod rover being evaluated for eventual flight to Mars. RTI's ControlShell is complex, real-time command and control software, capable of processing information and controlling mechanical devices. One ControlShell tool is StethoScope. As a real-time data collection and display tool, StethoScope allows a user to see how a program is running without changing its execution. RTI has successfully applied its software savvy in other arenas, such as telecommunications, networking, video editing, semiconductor manufacturing, automobile systems, and medical imaging.

  10. Voltage Controller

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Power Efficiency Corporation, specifically formed to manufacture and develop products from NASA technology, has a license to a three-phase power factor controller originally developed by Frank Nola, an engineer at Marshall Space Flight Center. Power Efficiency and two major distributors, Performance Control and Edison Power Technologies, use the electronic control boards to assemble three different motor controllers: Power Commander, Performance Controller, and Energy Master. The company Power Factor Controller reduces excessive energy waste in AC induction motors. It is used in industries and applications where motors operate under variable loads, including elevators and escalators, machine tools, intake and exhaust fans, oil wells, conveyors, pumps, die casting, and compressors. Customer lists include companies such as May Department Stores, Caesars Atlantic City, Ford Motors, and American Axle.

  11. Mosquito Control

    MedlinePlus

    Jump to main content US EPA United States Environmental Protection Agency Search Search Share Facebook Twitter Google+ Pinterest Contact Us Mosquito Control About Mosquitoes General Information Life ...

  12. Power Controller

    NASA Astrophysics Data System (ADS)

    1983-01-01

    The power factor controller (PFC) senses shifts in the relationship between voltage and current, and matches them with a motor's need. This prevents waste as motors do not need a high voltage when they are not operating at full load conditions. PFC is manufactured by Nordic Controls Company, among others, and has proved extremely cost effective.

  13. CONTROL ROD

    DOEpatents

    Walker, D.E.; Matras, S.

    1963-04-30

    This patent shows a method of making a fuel or control rod for a nuclear reactor. Fuel or control material is placed within a tube and plugs of porous metal wool are inserted at both ends. The metal wool is then compacted and the tube compressed around it as by swaging, thereby making the plugs liquid- impervious but gas-pervious. (AEC)

  14. Environmental Controls.

    ERIC Educational Resources Information Center

    Schneiderman, Helen, Ed.

    1994-01-01

    Environmental control units, or ECUs, are devices or systems which allow for alternate access to electronic or electrical devices and those objects, like draperies and doors, which may be adapted for use with electricity. Such devices offer the person with a mobility limitation the opportunity to control his or her environment, thus enhancing the…

  15. Symptom control.

    PubMed

    Chang, Victor T; Ingham, Jane

    2003-01-01

    Symptom control has become increasingly recognized as an important goal in patient care. In this article, advances in symptom assessment, and various definitions of symptom improvement are reviewed. Theoretical concepts underlying symptom control and clinically significant change are presented, as well as the role of symptom control as an endpoint in clinical trials. Symptom control is then surveyed in two broad categories for selected symptoms. The first area is therapy related symptoms, secondary to chemotherapy, radiation, hormonal therapy, and surgery. Symptoms reviewed include chemotherapy related mucositis, emesis, fatigue; hot flashes; and radiation related dermatitis, xerostomia, and mucositis. The second area is palliative oncologic approaches to disease-related symptoms. Results in palliative chemotherapy, palliative radiation therapy, cancer pain, and lack of appetite are summarized. Areas requiring further research are noted. Findings are presented in both a clinical and research context to help guide the reader with interpreting symptom control studies.

  16. Detonation control

    SciTech Connect

    Mace, Jonathan L.; Seitz, Gerald J.; Bronisz, Lawrence E.

    2016-10-25

    Detonation control modules and detonation control circuits are provided herein. A trigger input signal can cause a detonation control module to trigger a detonator. A detonation control module can include a timing circuit, a light-producing diode such as a laser diode, an optically triggered diode, and a high-voltage capacitor. The trigger input signal can activate the timing circuit. The timing circuit can control activation of the light-producing diode. Activation of the light-producing diode illuminates and activates the optically triggered diode. The optically triggered diode can be coupled between the high-voltage capacitor and the detonator. Activation of the optically triggered diode causes a power pulse to be released from the high-voltage capacitor that triggers the detonator.

  17. Aiming Control.

    DTIC Science & Technology

    1987-10-01

    positive definite solution of A1Qy+QyAo+I--QyBBTQY=O (5.2) The logarithmic residence time of system (3.1) with the stabilizing control (5.1) in a I...a bounded is E bou,,,,dby, ii I)-2=(6 2 This completes the prooof the necesity. Suffidency: The proof is by conatnction. Select a stabilizing control u...a - . Q.LD. Proof of Theorem 3.3: It follows from the results of [151, [21] that for each y > 0, K? defined by (3.4) is a stabilizing control and

  18. REACTOR CONTROL

    DOEpatents

    Fortescue, P.; Nicoll, D.

    1962-04-24

    A control system employed with a high pressure gas cooled reactor in which a control rod is positioned for upward and downward movement into the neutron field from a position beneath the reactor is described. The control rod is positioned by a coupled piston cylinder releasably coupled to a power drive means and the pressurized coolant is directed against the lower side of the piston. The coolant pressure is offset by a higher fiuid pressure applied to the upper surface of the piston and means are provided for releasing the higher pressure on the upper side of the piston so that the pressure of the coolant drives the piston upwardly, forcing the coupled control rod into the ncutron field of the reactor. (AEC)

  19. Under Control.

    ERIC Educational Resources Information Center

    Henry, Rich

    2001-01-01

    Offers advice on how school administrators can properly plan and monitor school construction projects to contain costs. Cost control tips discussed include project scope definition, contract bidding and awarding practice, and project management techniques. (GR)

  20. CONTROL ROD

    DOEpatents

    Zinn, W.H.; Ross, H.V.

    1958-11-18

    A control rod is described for a nuclear reactor. In certaln reactor designs it becomes desirable to use a control rod having great width but relatively llttle thickness. This patent is addressed to such a need. The neutron absorbing material is inserted in a triangular tube, leaving volds between the circular insert and the corners of the triangular tube. The material is positioned within the tube by the use of dummy spacers to achleve the desired absorption pattern, then the ends of the tubes are sealed with suitable plugs. The tubes may be welded or soldered together to form two flat surfaces of any desired width, and covered with sheetmetal to protect the tubes from damage. This design provides a control member that will not distort under the action of outside forces or be ruptured by gases generated within the jacketed control member.

  1. Drug Control

    ERIC Educational Resources Information Center

    Leviton, Harvey S.

    1975-01-01

    This article attempts to assemble pertinent information about the drug problem, particularily marihuana. It also focuses on the need for an educational program for drug control with the public schools as the main arena. (Author/HMV)

  2. CONTROL SYSTEM

    DOEpatents

    Shannon, R.H.; Williamson, H.E.

    1962-10-30

    A boiling water type nuclear reactor power system having improved means of control is described. These means include provisions for either heating the coolant-moderator prior to entry into the reactor or shunting the coolantmoderator around the heating means in response to the demand from the heat engine. These provisions are in addition to means for withdrawing the control rods from the reactor. (AEC)

  3. Airspace Control

    DTIC Science & Technology

    2011-02-02

    it does not display a currently valid OMB control number. 1 . REPORT DATE 02 FEB 2011 2. REPORT TYPE 3. DATES COVERED 00-00-2011 to 00-00-2011 4...each other; select the best course of action; and produce a joint operation plan or order (JP 1 - 02 ). A major element of the JOPP is campaign planning... 1 - 02 ). Airspace control should be integrated throughout the JOPP and campaign planning to ensure joint air operations support the JFC‘s plan.60

  4. Controlling turbulence

    NASA Astrophysics Data System (ADS)

    Kühnen, Jakob; Hof, Björn

    2015-11-01

    We show that a simple modification of the velocity profile in a pipe can lead to a complete collapse of turbulence and the flow fully relaminarises. The annihilation of turbulence is achieved by a steady manipulation of the streamwise velocity component alone, greatly reducing control efforts. Several different control techniques are presented: one with a local modification of the flow profile by means of a stationary obstacle, one employing a nozzle injecting fluid through a small gap at the pipe wall and one with a moving wall, where a part of the pipe is shifted in the streamwise direction. All control techniques act on the flow such that the streamwise velocity profile becomes more flat and turbulence gradually grows faint and disappears. In a smooth straight pipe the flow remains laminar downstream of the control. Hence a reduction in skin friction by a factor of 8 and more can be accomplished. Stereoscopic PIV-measurements and movies of the development of the flow during relaminarisation are presented.

  5. Motor Controllers

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Kollmorgen Corporation's Mermaid II two person submersible is propeller-driven by a system of five DC brushless motors with new electronic controllers that originated in work performed in a NASA/DOE project managed by Lewis Research Center. A key feature of the system is electric commutation rather than mechanical commutation for converting AC current to DC.

  6. Dynamics & Control

    DTIC Science & Technology

    2012-03-06

    This project takes the first steps towards a “Compressive Information Extraction” paradigm: Unmanned vehicles Flight and perch sensors Human in the...the program has solid efforts in control of MAVs, hypersonic vehicles , smart materials and biological systems. • Support of fundamental research...BRIEF DESCRIPTION OF PORTFOLIO: Developing mathematical theory and algorithms based on the interplay of dynamical systems and

  7. Birth Control

    MedlinePlus

    ... your health, frequency of sexual activity, number of sexual partners and desire to have children in the future. Your health care provider can help you select the best form of birth control for you. NIH: National Institute of Child Health and Human Development

  8. Asymptotic controllability and optimal control

    NASA Astrophysics Data System (ADS)

    Motta, M.; Rampazzo, F.

    We consider a control problem where the state must approach asymptotically a target C while paying an integral cost with a non-negative Lagrangian l. The dynamics f is just continuous, and no assumptions are made on the zero level set of the Lagrangian l. Through an inequality involving a positive number p and a Minimum Restraint FunctionU=U(x) - a special type of Control Lyapunov Function - we provide a condition implying that (i) the system is asymptotically controllable, and (ii) the value function is bounded by U/p. The result has significant consequences for the uniqueness issue of the corresponding Hamilton-Jacobi equation. Furthermore it may be regarded as a first step in the direction of a feedback construction.

  9. COPD - control drugs

    MedlinePlus

    Chronic obstructive pulmonary disease - control drugs; Bronchodilators - COPD - control drugs; Beta agonist inhaler - COPD - control drugs; Anticholinergic inhaler - COPD - control drugs; Long-acting inhaler - COPD - control drugs; ...

  10. Vehicle Controller

    NASA Technical Reports Server (NTRS)

    1985-01-01

    UNISTICK is an airplane-like joystick being developed by Johnson Engineering under NASA and VA sponsorship. It allows a driver to control a vehicle with one hand, and is based upon technology developed for the Apollo Lunar Landings of the 1970's. It allows severely handicapped drivers to operate an automobile or van easily. The system is expected to be in production by March 1986.

  11. Autonomous control

    NASA Technical Reports Server (NTRS)

    Brown, Barbara

    1990-01-01

    KSC has been developing the Knowledge-Based Autonomous Test Engineer (KATE), which is a tool for performing automated monitoring, diagnosis, and control of electromechanical devices. KATE employs artificial intelligence computing techniques to perform these functions. The KATE system consists of a generic shell and a knowledge base. The KATE shell is the portion of the system which performs the monitoring, diagnosis, and control functions. It is generic in the sense that it is application independent. This means that the monitoring activity, for instance, will be performed with the same algorithms regardless of the particular physical device being used. The knowledge base is the portion of the system which contains specific functional and behavorial information about the physical device KATE is working with. Work is nearing completion on a project at KSC to interface a Texas Instruments Explorer running a LISP version of KATE with a Generic Checkout System (GCS) test-bed to control a physical simulation of a shuttle tanking system (humorously called the Red Wagon because of its color and mobility). The Autonomous Control System (ACS) project supplements and extends the KATE/GCS project by adding three other major activities. The activities include: porting KATE from the Texas Instruments Explorer machine to an Intel 80386-based UNIX workstation in the LISP language; rewriting KATE as necessary to run on the same 80386 workstation but in the Ada language; and investigating software and techniques to translate ANSI Standard Common LISP to Mil Standard Ada. Primary goals of this task are as follows: (1) establish the advantages of using expert systems to provide intelligent autonomous software for Space Station Freedom applications; (2) determine the feasibility of using Ada as the run-time environment for model-based expert systems; (3) provide insight into the advantages and disadvantagesof using LISP or Ada in the run-time environment for expert systems; and (4

  12. REACTOR CONTROL

    DOEpatents

    Ruano, W.J.

    1957-12-10

    This patent relates to nuclear reactors of the type which utilize elongited rod type fuel elements immersed in a liquid moderator and shows a design whereby control of the chain reaction is obtained by varying the amount of moderator or reflector material. A central tank for containing liquid moderator and fuel elements immersed therein is disposed within a surrounding outer tank providing an annular space between the two tanks. This annular space is filled with liquid moderator which functions as a reflector to reflect neutrons back into the central reactor tank to increase the reproduction ratio. Means are provided for circulating and cooling the moderator material in both tanks and additional means are provided for controlling separately the volume of moderator in each tank, which latter means may be operated automatically by a neutron density monitoring device. The patent also shows an arrangement for controlling the chain reaction by injecting and varying an amount of poisoning material in the moderator used in the reflector portion of the reactor.

  13. Signature control

    NASA Astrophysics Data System (ADS)

    Pyati, Vittal P.

    The reduction of vehicle radar signature is accomplished by means of vehicle shaping, the use of microwave frequencies-absorbent materials, and either passive or active cancellation techniques; such techniques are also useful in the reduction of propulsion system-associated IR emissions. In some anticipated scenarios, the objective is not signature-reduction but signature control, for deception, via decoy vehicles that mimic the signature characteristics of actual weapons systems. As the stealthiness of airframes and missiles increases, their propulsion systems' exhaust plumes assume a more important role in detection by an adversary.

  14. Thermal control

    NASA Astrophysics Data System (ADS)

    Haslett, B.

    1984-02-01

    There are basically three key ingredients to the thermal control system for any large space platform or space station. These are heat rejection (from a centralized radiator or from body mounted radiators), heat acquisition (from payloads), and heat transport (via a transport loop to the radiator). The echnical approach in the heat rejection area is to construct the radiator from individual elements so that it can be built on-orbit, is very insensitive to meteoroid and debris hazards, and is repairable. In the area of thermal acquisition and transport an added effort to better understand two phase flow in zero gravity by analysis and testing is suggested.

  15. Heliostat control

    DOEpatents

    Kaehler, James A.

    1984-01-01

    An improvement in a system and method of controlling heliostat in which the heliostat is operable in azimuth and elevation by respective stepper motors and including the respective steps or means for calculating the position for the heliostat to be at a commanded position, determining the number of steps in azimuth and elevation for each respective motor to get to the commanded position and energizing both the azimuth and elevation stepper motors to run in parallel until predetermined number of steps away from the closest commanded position in azimuth and elevation so that the closest position has been achieved, and thereafter energizing only the remaining motor to bring it to its commanded position. In this way, the heliostat can be started from a stowed position in the morning and operated by a computer means to its commanded position and kept correctly oriented throughout the day using only the time of the day without requiring the usual sensors and feedback apparatus. A computer, or microprocessor, can then control a plurality of many heliostats easily and efficiently throughout the day.

  16. [Controlled hypernatremia].

    PubMed

    Petit, L; Masson, F; Cottenceau, V; Sztark, F

    2006-08-01

    Hypernatremia exerts its main effect on the brain through the osmotic gradient it creates on either side of the blood brain barrier, which is impermeable to sodium. This generates a transfer of water from the intracellular to the vascular sector leading to temporary cell shrinkage. Osmoregulation permits cerebral cells to accumulate osmoactive molecules in order to restore their initial volume. It has been demonstrated in animals with brain injury that intracellular dehydration occurs essentially in the nonlesioned hemisphere. In most experimental studies, the reduction in cerebral volume obtained by hypertonic saline (HS) perfusion is accompanied by an intracranial pressure decrease, even under hemorrhagic shock conditions. Initially, clinical studies successfully used HS, as an alternative to mannitol, in the treatment of acute and refractory intracranial hypertension. Then continuous infusion of HS, with the objective of inducing hypernatremia, had produced encouraging effects on intracranial pressure control. However, these results were limited to non-randomized studies, without control groups and mainly in pediatric patients. Nevertheless, the use of HS on intracranial hypertension, refractory to conventional treatments, could be reasonable under strict monitoring of natremia as well as its adverse effects.

  17. Control apparatus

    NASA Technical Reports Server (NTRS)

    Derkacs, Thomas (Inventor); Fetheroff, Charles W. (Inventor); Matay, Istvan M. (Inventor); Toth, Istvan J. (Inventor)

    1982-01-01

    Although the method and apparatus of the present invention can be utilized to apply either a uniform or a nonuniform covering of material over many different workpieces, the apparatus (20) is advantageously utilized to apply a thermal barrier covering (64) to an airfoil (22) which is used in a turbine engine. The airfoil is held by a gripper assembly (86) while a spray gun (24) is effective to apply the covering over the airfoil. When a portion of the covering has been applied, a sensor (28) is utilized to detect the thickness of the covering. A control apparatus (32) compares the thickness of the covering of material which has been applied with the desired thickness and is subsequently effective to regulate the operation of the spray gun to adaptively apply a covering of a desired thickness with an accuracy of at least plus or minus 0.0015 inches (1.5 mils) despite unanticipated process variations.

  18. Custom controls

    NASA Astrophysics Data System (ADS)

    Butell, Bart

    1996-02-01

    Microsoft's Visual Basic (VB) and Borland's Delphi provide an extremely robust programming environment for delivering multimedia solutions for interactive kiosks, games and titles. Their object oriented use of standard and custom controls enable a user to build extremely powerful applications. A multipurpose, database enabled programming environment that can provide an event driven interface functions as a multimedia kernel. This kernel can provide a variety of authoring solutions (e.g. a timeline based model similar to Macromedia Director or a node authoring model similar to Icon Author). At the heart of the kernel is a set of low level multimedia components providing object oriented interfaces for graphics, audio, video and imaging. Data preparation tools (e.g., layout, palette and Sprite Editors) could be built to manage the media database. The flexible interface for VB allows the construction of an infinite number of user models. The proliferation of these models within a popular, easy to use environment will allow the vast developer segment of 'producer' types to bring their ideas to the market. This is the key to building exciting, content rich multimedia solutions. Microsoft's VB and Borland's Delphi environments combined with multimedia components enable these possibilities.

  19. Birth Control Methods

    MedlinePlus

    ... Z Health Topics Birth control methods Birth control methods > A-Z Health Topics Birth control methods fact ... Publications email updates Enter email Submit Birth control methods Birth control (contraception) is any method, medicine, or ...

  20. CONTROL ROOM WITH SPRINKLER SYSTEM CONTROLS, INCLUDING MANUAL CONTROL BOXES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    CONTROL ROOM WITH SPRINKLER SYSTEM CONTROLS, INCLUDING MANUAL CONTROL BOXES FOR THE VENTILATION SYSTEM AND A PLC SWITCH FOR AUTOMATIC CO (CARBON MONOXIDE) SYSTEM. THE AIR TESTING SYSTEM IS FREE STANDING AND THE FANS ARE COMPUTER-OPERATED. - Alaskan Way Viaduct and Battery Street Tunnel, Seattle, King County, WA

  1. Contact Control, Version 1

    SciTech Connect

    von Sternberg, Alex

    2016-07-21

    The contact control code is a generalized force control scheme meant to interface with a robotic arm being controlled using the Robot Operating System (ROS). The code allows the user to specify a control scheme for each control dimension in a way that many different control task controllers could be built from the same generalized controller. The input to the code includes maximum velocity, maximum force, maximum displacement, and a control law assigned to each direction and the output is a 6 degree of freedom velocity command that is sent to the robot controller.

  2. First description of Leishmania (Viannia) infection in Evandromyia saulensis, Pressatia sp. and Trichophoromyia auraensis (Psychodidae: Phlebotominae) in a transmission area of cutaneous leishmaniasis in Acre state, Amazon Basin, Brazil

    PubMed Central

    de Araujo-Pereira, Thais; de Pita-Pereira, Daniela; Boité, Mariana Côrtes; Melo, Myllena; da Costa-Rego, Taiana Amancio; Fuzari, Andressa Alencastre; Brazil, Reginaldo Peçanha; Britto, Constança

    2017-01-01

    Studies on the sandfly fauna to evaluate natural infection indexes are still limited in the Brazilian Amazon, a region with an increasing incidence of cutaneous leishmaniasis. Here, by using a multiplex polymerase chain reaction directed to Leishmania kDNA and hybridisation, we were able to identify L. (Viannia) subgenus in 12 out of 173 sandflies captured in the municipality of Rio Branco, Acre state, revealing a positivity of 6.94%. By sequencing the Leishmania 234 bp-hsp70 amplified products from positive samples, infection by L. (V.) braziliensis was confirmed in five sandflies: one Evandromyia saulensis, three Trichophoromyia auraensis and one Pressatia sp. The finding of L. (Viannia) DNA in two Ev. saulensis corresponds to the first record of possible infection associated with this sandfly. Moreover, our study reveals for the first time in Brazil, Th. auraensis and Pressatia sp. infected by L. (Viannia) parasites. PMID:28076470

  3. Taphofacies of Lower-Middle Pennsylvanian marine invertebrates from the Monte Alegre and Itaituba formations, part of the outcropped marine sequence of the Tapajós Group (Southern Amazonas Basin, Brazil) - regional palaeoecological models

    NASA Astrophysics Data System (ADS)

    Moutinho, L. P.; Scomazzon, A. K.; Nascimento, S.; Lemos, V. B.

    2016-10-01

    One of the most relevant characteristics of the Pennsylvanian shallow-water carbonates of the Amazonas Basin is its diverse and well preserved invertebrate fossiliferous assemblages. In order to better understand the origin of these fossil concentrations, taphonomic data were obtained along well exposed areas of the uppermost part of the Monte Alegre Formation and basal part of the Itaituba Formation, which, based on conodonts, fusulinids and palynomorphs is of Atokan age. The taphonomic data focused on invertebrate organisms were supported by petrographic analysis. The understanding of the stacking pattern of the strata in the studied section allowed the identification of five type taphofacies, which contributed in the development of regional palaeoecological models, expressed as block-diagrams. These characterize the distribution of the environmental parameters, the composition of the faunal associations and the distribution and amplitude of the taphonomic processes that created the taphonomic signatures of the bioclastic elements throughout the supratidal to lower intertidal/deep subtidal depositional environments pertinent to the studied depositional environment. The regional palaeoecological models here presented are related to the particularities of the depositional environments of the studied rocks and are exclusive for the characterization of this intracratonic basin set influenced by high frequency climatic variations. Lithofacies, biofacies and taphofacies associations also reflect depositional conditions pertinent to the studied regional context, differing from the elements observed in modern intracratonic contexts analogous to the one studied, from different sedimentary basins around the world. Therefore, invertebrate taphonomy, supported by the analysis of sedimentary facies, fulfills the purposes recommended in this work, demonstrating its potential as a tool for palaeoecological analysis in the Pennsylvanian outcropping section in the southern platform of the Amazonas Basin.

  4. Effects of a regional décollement level for gravity tectonics on late Neogene-Quaternary deep-sea clastic sedimentation in the Foz do Amazonas Basin, Brazil

    NASA Astrophysics Data System (ADS)

    Cruz, A. M.; Gorini, C.

    2015-12-01

    Sets of 2D multi-channel seismic and chronostratigraphic data allowed us to undertake analyses of source to sink processes and triggering mechanisms of the gigantic megaslides previously documented off the NW and SE steep slope settings of the Foz do Amazonas basin. These megaslides comprise two sets of stacked allochthonous masses within the Upper Miocene-Quaternary sedimentary record, now described as Mass-Transport Complexes (MTCs): the Amapá Megaslide Complex (AMC) and the Pará-Maranhão Megaslide Complex (PMMC). Individual megaslides of both MTCs can mobilize to deep waters up to kilometer thick sedimentary series as allochthonous masses with different flow directions, degrees of sediment disruption and internal coherence. Megaslides spread downslope over areas as large as thousands of km2, attaining dimensions comparable to the world's largest mass-transport deposits. The basal and largest megaslide of the AMC (AM1 megaslide) is a quite unique example of mass-transport deposit, since it is interpreted as a dominant carbonate allochthonous mass sourced from a mixed carbonate-siliciclastic platform. According to stratigraphic correlations with global sea-level positions, platform instability would have been triggered between the late Miocene and the end of the Early Pliocene by gravitational collapse of the mixed platform under its own weight, after successive subaerial exposures which were able to generate karstification processes. Siliciclastic-type megaslides, on the other hand, are all sourced from large upslope slide and/or rotated blocks (up to 60 km large in the case of the PMMC).Stratigraphic correlations evidenced that horizon equally acts as the upper décollement level for the gravity tectonic system that operates in the regional scale of the Foz do Amazonas basin. In such a context, results of this work evidence complex links between variable modes of gravity deformation (gravity tectonics and mass wasting), all induced by instability created from a condensed section prone to produce pore fluid overpressure.

  5. Chromosome studies of Astyanax jacuhiensis Cope, 1894 (Characidae) from the Tramandai River Basin, Brazil, using in situ hybridization with the 18S rDNA probe, DAPI and CMA3 staining.

    PubMed

    da Silva, Laura Lahr Lourenço; Giuliano-Caetano, Lucia; Dias, Ana Lúcia

    2012-01-01

    The genus Astyanax comprises 86 species of fish distributed in Brazilian river basins and is considered of the Incertae sedis group within the family Characidae. This study presents an analysis of 12 specimens of Astyanax jacuhiensis from the Tramandai River Basin, RS Brazil: 6 from the Maquiné River and 6 from the Quadros Lagoon. All specimens showed a diploid number equal to 50 chromosomes with different karyotypic formula between the two localities. The population from the Maquiné River showed 10m+26sm+6st+8a (FN=92). Fish from the Quadros Lagoon showed 12m+20sm+6st+12a (FN=88). AgNORs were evidenced in the short arm of one acrocentric chromosome pair in both populations, confirmed by FISH with the 18S rDNA probe. CMA3 fluorochrome corresponded with the AgNOR sites, while DAPI staining was negative in these regions. C banding revealed that heterochromatin was weakly distributed, mainly in the pericentromeric and terminal regions in most chromosomes. Analyses of male gonadal tissue were conducted with the objective of characterizing the meiotic chromosome behavior in A. jacuhiensis. The following stages were evidenced: spermatogonial with 50 chromosomes, pachytene and metaphase I with 25 bivalents, and metaphase II with 25 chromosomes, thus confirming the diploid number of the species. Chromosomal abnormalities were not observed. This study shows preliminary data on A. jacuhiensis from the Tramandai River Basin, contributing with more chromosomal information for this group of fish.

  6. First description of Leishmania (Viannia) infection in Evandromyia saulensis, Pressatia sp. and Trichophoromyia auraensis (Psychodidae: Phlebotominae) in a transmission area of cutaneous leishmaniasis in Acre state, Amazon Basin, Brazil.

    PubMed

    Araujo-Pereira, Thais de; Pita-Pereira, Daniela de; Boité, Mariana Côrtes; Melo, Myllena; Costa-Rego, Taiana Amancio da; Fuzari, Andressa Alencastre; Brazil, Reginaldo Peçanha; Britto, Constança

    2017-01-01

    Studies on the sandfly fauna to evaluate natural infection indexes are still limited in the Brazilian Amazon, a region with an increasing incidence of cutaneous leishmaniasis. Here, by using a multiplex polymerase chain reaction directed to Leishmania kDNA and hybridisation, we were able to identify L. (Viannia) subgenus in 12 out of 173 sandflies captured in the municipality of Rio Branco, Acre state, revealing a positivity of 6.94%. By sequencing the Leishmania 234 bp-hsp70 amplified products from positive samples, infection by L. (V.) braziliensis was confirmed in five sandflies: one Evandromyia saulensis, three Trichophoromyia auraensis and one Pressatia sp. The finding of L. (Viannia) DNA in two Ev. saulensis corresponds to the first record of possible infection associated with this sandfly. Moreover, our study reveals for the first time in Brazil, Th. auraensis and Pressatia sp. infected by L. (Viannia) parasites.

  7. Neural control: Chaos control sets the pace

    NASA Astrophysics Data System (ADS)

    Schöll, Eckehard

    2010-03-01

    Even simple creatures, such as cockroaches, are capable of complex responses to changes in their environment. But robots usually require complicated dedicated control circuits to perform just a single action. Chaos control theory could allow simpler control strategies to realize more complex behaviour.

  8. Superconducting fault current controller/current controller

    DOEpatents

    Cha, Yung S.

    2004-06-15

    A superconducting fault current controller/current controller employs a superconducting-shielded core reactor (SSCR) with a variable impedance in a secondary circuit to control current in a primary circuit such as an electrical distribution system. In a second embodiment, a variable current source is employed in a secondary circuit of an SSCR to control current in the primary circuit. In a third embodiment, both a variable impedance in one secondary circuit and a variable current source in a second circuit of an SSCR are employed for separate and independent control of current in the primary circuit.

  9. Vehicle Dynamics and Control

    NASA Astrophysics Data System (ADS)

    Rajamani, Rajesh

    Vehicle Dynamics and Control provides a comprehensive coverage of vehicle control systems and the dynamic models used in the development of these control systems. The control system topics covered in the book include cruise control, adaptive cruise control, ABS, automated lane keeping, automated highway systems, yaw stability control, engine control, passive, active and semi-active suspensions, tire models and tire-road friction estimation. In developing the dynamic model for each application, an effort is made to both keep the model simple enough for control system design but at the same time rich enough to capture the essential features of the dynamics.

  10. Controllability of asynchronous Boolean multiplex control networks

    NASA Astrophysics Data System (ADS)

    Luo, Chao; Wang, Xingyuan; Liu, Hong

    2014-09-01

    In this article, the controllability of asynchronous Boolean multiplex control networks (ABMCNs) is studied. First, the model of Boolean multiplex control networks under Harvey' asynchronous update is presented. By means of semi-tensor product approach, the logical dynamics is converted into linear representation, and a generalized formula of control-depending network transition matrices is achieved. Second, a necessary and sufficient condition is proposed to verify that only control-depending fixed points of ABMCNs can be controlled with probability one. Third, using two types of controls, the controllability of system is studied and formulae are given to show: (a) when an initial state is given, the reachable set at time s under a group of specified controls; (b) the reachable set at time s under arbitrary controls; (c) the specific probability values from a given initial state to destination states. Based on the above formulae, an algorithm to calculate overall reachable states from a specified initial state is presented. Moreover, we also discuss an approach to find the particular control sequence which steers the system between two states with maximum probability. Examples are shown to illustrate the feasibility of the proposed scheme.

  11. Malagasy Backward Object Control

    ERIC Educational Resources Information Center

    Potsdam, Eric

    2009-01-01

    Backward control is an obligatory interpretational dependency between an overt controller and a nonovert controllee in which the controllee is structurally superior to the controller: "Meg persuaded [Delta]i" ["Roni to give up"]. It contrasts with ordinary forward control, in which the controller is structurally higher: "Meg persuaded Roni"…

  12. PID controllers' fragility.

    PubMed

    Alfaro, Víctor M

    2007-10-01

    In this paper, an index for measuring fragility of proportional integral derivative (PID) controllers is proposed. This index relates the losses of robustness of the control loop when controller parameters change, to the nominal robustness of the control loop. Furthermore, it defines when a PID controller is fragile, nonfragile or resilient.

  13. Directions in propulsion control

    NASA Technical Reports Server (NTRS)

    Lorenzo, Carl F.

    1990-01-01

    Discussed here is research at NASA Lewis in the area of propulsion controls as driven by trends in advanced aircraft. The objective of the Lewis program is to develop the technology for advanced reliable propulsion control systems and to integrate the propulsion control with the flight control for optimal full-system control.

  14. Structural Pest Control.

    ERIC Educational Resources Information Center

    Kahn, M. S.; Hoffman, W. M.

    This manual is designed for those who seek certification as pesticide applicators for industrial, institutional, structural, and health-related pest control. It is divided into six sections covering general pest control, wood-destroying organisms, bird control, fumigation, rodent control, and industrial weed control. The manual gives information…

  15. AIR POLLUTION CONTROL TECHNOLOGIES

    EPA Science Inventory

    This is a chapter for John Wiley & Son's Mechanical Engineers' Handbook, and covers issues involving air pollution control. Various technologies for controlling sulfur oxides is considered including fuel desulfurization. It also considers control of nitrogen oxides including post...

  16. Xenon International Automated Control

    SciTech Connect

    2016-08-05

    The Xenon International Automated Control software monitors, displays status, and allows for manual operator control as well as fully automatic control of multiple commercial and PNNL designed hardware components to generate and transmit atmospheric radioxenon concentration measurements every six hours.

  17. OPTIMUM SYSTEMS CONTROL,

    DTIC Science & Technology

    Variational calculus and continuous optimal control, (4) The maximum principle and Hamilton Jacobi theory, (5) Optimum systems control examples, (6...Discrete variational calculus and the discrete maximum principle, (7) Optimum control of distributed parameter systems, (8) Optimum state estimation in

  18. Essure Permanent Birth Control

    MedlinePlus

    ... and Prosthetics Essure Permanent Birth Control Essure Permanent Birth Control Share Tweet Linkedin Pin it More sharing options ... Essure System Essure is a a permanently implanted birth control device for women (female sterilization). Implantation of Essure ...

  19. Gross motor control

    MedlinePlus

    Gross motor control is the ability to make large, general movements (such as waving an arm or lifting a ... Gross motor control is a milestone in the development of an infant. Infants develop gross motor control before they ...

  20. Integrated Control Using the SOFFT Control Structure

    NASA Technical Reports Server (NTRS)

    Halyo, Nesim

    1996-01-01

    The need for integrated/constrained control systems has become clearer as advanced aircraft introduced new coupled subsystems such as new propulsion subsystems with thrust vectoring and new aerodynamic designs. In this study, we develop an integrated control design methodology which accomodates constraints among subsystem variables while using the Stochastic Optimal Feedforward/Feedback Control Technique (SOFFT) thus maintaining all the advantages of the SOFFT approach. The Integrated SOFFT Control methodology uses a centralized feedforward control and a constrained feedback control law. The control thus takes advantage of the known coupling among the subsystems while maintaining the identity of subsystems for validation purposes and the simplicity of the feedback law to understand the system response in complicated nonlinear scenarios. The Variable-Gain Output Feedback Control methodology (including constant gain output feedback) is extended to accommodate equality constraints. A gain computation algorithm is developed. The designer can set the cross-gains between two variables or subsystems to zero or another value and optimize the remaining gains subject to the constraint. An integrated control law is designed for a modified F-15 SMTD aircraft model with coupled airframe and propulsion subsystems using the Integrated SOFFT Control methodology to produce a set of desired flying qualities.

  1. Dynamic power flow controllers

    DOEpatents

    Divan, Deepakraj M.; Prasai, Anish

    2017-03-07

    Dynamic power flow controllers are provided. A dynamic power flow controller may comprise a transformer and a power converter. The power converter is subject to low voltage stresses and not floated at line voltage. In addition, the power converter is rated at a fraction of the total power controlled. A dynamic power flow controller controls both the real and the reactive power flow between two AC sources having the same frequency. A dynamic power flow controller inserts a voltage with controllable magnitude and phase between two AC sources; thereby effecting control of active and reactive power flows between two AC sources.

  2. Biological Control in Agroecosystems

    NASA Astrophysics Data System (ADS)

    Batra, Suzanne W. T.

    1982-01-01

    Living organisms are used as biological pest control agents in (i) classical biological control, primarily for permanent control of introduced perennial weed pests or introduced pests of perennial crops; (ii) augmentative biological control, for temporary control of native or introduced pests of annual crops grown in monoculture; and (iii) conservative or natural control, in which the agroecosystem is managed to maximize the effect of native or introduced biological control agents. The effectiveness of biological control can be improved if it is based on adequate ecological information and theory, and if it is integrated with other pest management practices.

  3. CONTROL LIMITER DEVICE

    DOEpatents

    DeShong, J.A.

    1960-03-01

    A control-limiting device for monltoring a control system is described. The system comprises a conditionsensing device, a condition-varying device exerting a control over the condition, and a control means to actuate the condition-varying device. A control-limiting device integrates the total movement or other change of the condition-varying device over any interval of time during a continuum of overlapping periods of time, and if the tothl movement or change of the condition-varying device exceeds a preset value, the control- limiting device will switch the control of the operated apparatus from automatic to manual control.

  4. Integrated blending control system

    SciTech Connect

    Cogbill, R.B.; Dodd, T.J.; Heilman, P.W.; Heronemus, D.L.; Sears, L.R.; Berryman, L.N.; Baker, R.L.; Guffee, L.E.; Prucha, D.A.; Roberts, D.M.

    1989-07-25

    This patent describes a proppant control system. It comprises: storage bin means for storing particulate material; surge bin means for receiving a flow of the particulate material from the storage bin means; first conveyor means for providing a flow of particulate material to the surge bin means from the storage bin means; second conveyor means for transferring a controllable quantity of the particulate material from the surge bin means; and proppant control means. The control means include: first speed control means for remotely controlling the speed of the first conveyor means; and second speed control means for remotely controlling the speed of the second conveyor means.

  5. Space Digital Controller for Improved Motor Control

    NASA Astrophysics Data System (ADS)

    Alves-Nunes, Samuel; Daras, Gaetan; Dehez, Bruno; Maillard, Christophe; Bekemans, Marc; Michel, Raymond

    2014-08-01

    Performing digital motor control into space equipment is a new challenge. The new DPC (Digital Programmable Controller) is the first chip that we can use as a micro-controller, allowing us to drive motors with digital control schemes. In this paper, the digital control of hybrid stepper motors is considered. This kind of motor is used for solar array rotation and antenna actuation. New digital control technology brings a lot of advantages, allowing an important reduction of thermal losses inside the motor, and a reduction of thermal constraints on power drive electronic components. The opportunity to drive motors with a digital controller also brings many new functionalities like post-failure torque analysis, micro- vibrations and cogging torque reduction, or electro- mechanical damping of solar array oscillations. To evaluate the performance of the system, Field-Oriented Control (FOC) is implemented on a hybrid stepper motor. A test-bench, made of an active load, has been made to emulate the mechanical behaviour of the solar array, by the use of a torsionally-compliant model. The experimental results show that we can drastically reduce electrical power consumption, compared with the currently used open-loop control scheme.

  6. Improving Control of Two Motor Controllers

    NASA Technical Reports Server (NTRS)

    Toland, Ronald W.

    2004-01-01

    A computer program controls motors that drive translation stages in a metrology system that consists of a pair of two-axis cathetometers. This program is specific to Compumotor Gemini (or equivalent) motors and the Compumotor 6K-series (or equivalent) motor controller. Relative to the software supplied with the controller, this program affords more capabilities and is easier to use. Written as a Virtual Instrument in the LabVIEW software system, the program presents an imitation control panel that the user can manipulate by use of a keyboard and mouse. There are three modes of operation: command, movement, and joystick. In command mode, single commands are sent to the controller for troubleshooting. In movement mode, distance, speed, and/or acceleration commands are sent to the controller. Position readouts from the motors and from position encoders on the translation stages are displayed in marked fields. At any time, the position readouts can be recorded in a file named by the user. In joystick mode, the program yields control of the motors to a joystick. The program sends commands to, and receives data from, the controller via a serial cable connection, using the serial-communication portion of the software supplied with the controller.

  7. Adaptive Cruise Control

    NASA Astrophysics Data System (ADS)

    Winner, Hermann; Danner, Bernd; Steinle, Joachim

    Mit Adaptive Cruise Control, abgekürzt ACC, wird eine Fahrgeschwindigkeitsregelung bezeichnet, die sich an die Verkehrssituation anpasst. Synonyme Bezeichnungen sind Aktive Geschwindigkeitsregelung, Automatische Distanzregelung oder Abstandsregeltempomat. Im englischen Sprachraum fnden sich die weiteren Bezeichnungen Active Cruise Control, Automatic Cruise Control oder Autonomous Intelligent Cruise Control. Als markengeschützte Bezeichnungen sind Distronic und Automatische Distanz-Regelung (ADR) eingetragen.

  8. Programable Multicrate Controller

    NASA Technical Reports Server (NTRS)

    Mook, G. L.; Phillips, M. R.

    1985-01-01

    High-speed, environmentally hardened controller developed for use with commercially available system crates for both experiment control and data handling. Programable crate controller consists of three functional areas: control section utilizes high-speed bit-slice circuitry, memory, and data way interface.

  9. Robot Manipulator Control.

    DTIC Science & Technology

    1983-03-07

    This report presents a synthetic approach for calculating the control of robot manipulators. The initial control problem is broken down into linear ... control and modelling problems. The approach allows derivation of numerous schemes (adaptive or not) of control proposed in the literature and suggests

  10. Aircraft adaptive learning control

    NASA Technical Reports Server (NTRS)

    Lee, P. S. T.; Vanlandingham, H. F.

    1979-01-01

    The optimal control theory of stochastic linear systems is discussed in terms of the advantages of distributed-control systems, and the control of randomly-sampled systems. An optimal solution to longitudinal control is derived and applied to the F-8 DFBW aircraft. A randomly-sampled linear process model with additive process and noise is developed.

  11. Microprocessor control for standardized power control systems

    NASA Technical Reports Server (NTRS)

    Green, D. G.; Perry, E.

    1978-01-01

    The use of microcomputers in space-oriented power systems as a replacement for existing inflexible analog type controllers has been proposed. This study examines multiprocessor systems, various modularity concepts and presents a conceptualized power system incorporating a multiprocessor controller as well as preliminary results from a breadboard model of the proposed system.

  12. Switching Systems: Controllability and Control Design

    DTIC Science & Technology

    2009-04-25

    observations motivates the necessity to search for other methods in order to obtain a useful algorithm that might test controllability in the sign...Contributions to the theory of optimal control,” Boletin de la Sociedad Matematica Mexicana, vol. 5, pp. 102–119, 1960. [38] Kellett, Christopher M. and Andrew R

  13. Control of space stations

    NASA Technical Reports Server (NTRS)

    Lee, K. Y.

    1983-01-01

    A study is made to develop controllers for the NASA-JSC Triangular Space Station and evaluate their performances to make recommendations for structural design and/or control alternatives. The control system design assumes the rigid body of the Space Station and developes the lumped parameter control system by using the Inverse Optimal Control Theory. In order to evaluate the performance of the control system, a Parameter Estimation algorithm is being developed which will be used in modeling an equivalent but simpler Space Station model. Finally, a scaled version of the Space Station is being built for the purpose of physical experiments to evaluate the control system performance.

  14. An intelligent traffic controller

    SciTech Connect

    Kagolanu, K.; Fink, R.; Smartt, H.; Powell, R.; Larsen, E.

    1995-12-01

    A controller with advanced control logic can significantly improve traffic flows at intersections. In this vein, this paper explores fuzzy rules and algorithms to improve the intersection operation by rationalizing phase changes and green times. The fuzzy logic for control is enhanced by the exploration of neural networks for families of membership functions and for ideal cost functions. The concepts of fuzzy logic control are carried forth into the controller architecture. Finally, the architecture and the modules are discussed. In essence, the control logic and architecture of an intelligent controller are explored.

  15. Nuclear reactor control apparatus

    DOEpatents

    Sridhar, Bettadapur N.

    1983-11-01

    Nuclear reactor core safety rod release apparatus comprises a control rod having a detent notch in the form of an annular peripheral recess at its upper end, a control rod support tube for raising and lowering the control rod under normal conditions, latches pivotally mounted on the control support tube with free ends thereof normally disposed in the recess in the control rod, and cam means for pivoting the latches out of the recess in the control rod when a scram condition occurs. One embodiment of the invention comprises an additional magnetically-operated latch for releasing the control rod under two different conditions, one involving seismic shock.

  16. HYDRAULIC SERVO CONTROL MECHANISM

    DOEpatents

    Hussey, R.B.; Gottsche, M.J. Jr.

    1963-09-17

    A hydraulic servo control mechanism of compact construction and low fluid requirements is described. The mechanism consists of a main hydraulic piston, comprising the drive output, which is connected mechanically for feedback purposes to a servo control piston. A control sleeve having control slots for the system encloses the servo piston, which acts to cover or uncover the slots as a means of controlling the operation of the system. This operation permits only a small amount of fluid to regulate the operation of the mechanism, which, as a result, is compact and relatively light. This mechanism is particuiarly adaptable to the drive and control of control rods in nuclear reactors. (auth)

  17. Engine roughness control means

    SciTech Connect

    Matsuura, M.; Doi, N.; Yoshioka, S.; Okimoto, H.; Veda, K.

    1987-08-04

    This patent describes a control system for a vehicle engine comprising engine condition detecting means for detecting an engine operating condition and producing an engine condition signal representing the engine operating condition, engine combustion control means for controlling a condition of combustion in the engine; and a control factor storage means for storing control factors for controlling the engine combustion. A modifying means connect the comparator means to receive the output signal and to modify the control factor from the storage means by the output of the comparator means so that the combustion control means is controlled by the modified control factor in a direction that the engine vibrations are suppressed. A reference signal changes means connected with the engine condition detecting means to change the reference roughness signal in accordance with the engine operating condition so that the reference signal is decreased when the engine is in idling operation.

  18. TFTR diagnostic vacuum controller

    SciTech Connect

    Olsen, D.; Persons, R.

    1981-01-01

    The TFTR diagnostic vacuum controller (DVC) provides in conjunction with the Central Instrumentation Control and Data Acquisition System (CICADA), control and monitoring for the pumps, valves and gauges associated with each individual diagnostic vacuum system. There will be approximately 50 systems on TFTR. Two standard versions of the controller (A and B) wil be provided in order to meet the requirements of two diagnostic manifold arrangements. All pump and valve sequencing, as well as protection features, will be implemented by the controller.

  19. Fuzzy and neural control

    NASA Technical Reports Server (NTRS)

    Berenji, Hamid R.

    1992-01-01

    Fuzzy logic and neural networks provide new methods for designing control systems. Fuzzy logic controllers do not require a complete analytical model of a dynamic system and can provide knowledge-based heuristic controllers for ill-defined and complex systems. Neural networks can be used for learning control. In this chapter, we discuss hybrid methods using fuzzy logic and neural networks which can start with an approximate control knowledge base and refine it through reinforcement learning.

  20. SODR Memory Control Buffer Control ASIC

    NASA Technical Reports Server (NTRS)

    Hodson, Robert F.

    1994-01-01

    The Spacecraft Optical Disk Recorder (SODR) is a state of the art mass storage system for future NASA missions requiring high transmission rates and a large capacity storage system. This report covers the design and development of an SODR memory buffer control applications specific integrated circuit (ASIC). The memory buffer control ASIC has two primary functions: (1) buffering data to prevent loss of data during disk access times, (2) converting data formats from a high performance parallel interface format to a small computer systems interface format. Ten 144 p in, 50 MHz CMOS ASIC's were designed, fabricated and tested to implement the memory buffer control function.

  1. Boiler control systems engineering

    SciTech Connect

    Gilman, J.

    2005-07-01

    The book provides in-depth coverage on how to safely and reliably control the firing of a boiler. Regardless of the capacity or fuel, certain fundamental control systems are required for boiler control. Large utility systems are more complex due to the number of burners and the overall capacity and equipment. This book covers engineering details on control systems and provides specific examples of boiler control including configuration and tuning. References to requirements are based on the 2004 NFPA 85 along with other ISA standards. Detailed chapters cover: Boiler fundamentals including piping and instrument diagrams (P&IDs) and a design basis checklist; Control of boilers, from strategies and bumpless transfer to interlock circuitry and final control elements; Furnace draft; Feedwater; Coal-fired boilers; Fuel and air control; Steam temperature; Burner management systems; Environment; and Control valve sizing. 2 apps.

  2. Digital Optical Control System

    NASA Astrophysics Data System (ADS)

    Jordan, David H.; Tipton, Charles A.; Christmann, Charles E.; Hochhausler, Nils P.

    1988-09-01

    We describe the digital optical control system (DOGS), a state-of-the-art controller for electrical feedback in an optical system. The need for a versatile optical controller arose from a number of unique experiments being performed by the Air Force Weapons Laboratory. These experiments use similar detectors and actuator-controlled mirrors, but the control requirements vary greatly. The experiments have in common a requirement for parallel control systems. The DOGS satisfies these needs by allowing several control systems to occupy a single chassis with one master controller. The architecture was designed to allow upward compatibility with future configurations. Combinations of off-the-shelf and custom boards are configured to meet the requirements of each experiment. The configuration described here was used to control piston error to X/80 at a wavelength of 0.51 Am. A peak sample rate of 8 kHz, yielding a closed loop bandwidth of 800 Hz, was achieved.

  3. Constrained control allocation

    NASA Technical Reports Server (NTRS)

    Durham, Wayne C.

    1992-01-01

    This paper addresses the problem of the allocation of several flight controls to the generation of specified body-axis moments. The number of controls is greater than the number of moments being controlled, and the ranges of the controls are constrained to certain limits. The controls are assumed to be individually linear in their effect throughout their ranges of motion, and independent of one another in their effects. The geometries of the subset of the constrained controls and of its image in moment space are examined. A direct method of allocating these several controls is presented, that guarantees the maximum possible moment is generated within the constraints of the controls. The results are illustrated by an example problem involving three controls and two moments.

  4. Control rod drive

    SciTech Connect

    Hawke, Basil C.

    1986-01-01

    A control rod drive uses gravitational forces to insert one or more control rods upwardly into a reactor core from beneath the reactor core under emergency conditions. The preferred control rod drive includes a vertically movable weight and a mechanism operatively associating the weight with the control rod so that downward movement of the weight is translated into upward movement of the control rod. The preferred control rod drive further includes an electric motor for driving the control rods under normal conditions, an electrically actuated clutch which automatically disengages the motor during a power failure and a decelerator for bringing the control rod to a controlled stop when it is inserted under emergency conditions into a reactor core.

  5. Spacecraft stability and control

    NASA Technical Reports Server (NTRS)

    Barret, Chris

    1992-01-01

    The Earth's first artificial satellite, Sputnik 1, slowly tumbled in orbit. The first U.S. satellite, Explorer 1, also tumbled out of control. Today, satellite stability and control has become a higher priority. For a satellite design that is to have a life expectancy of 14 years, appropriate spacecraft flight control systems will be reviewed, stability requirements investigated, and an appropriate flight control system recommended in order to see the design process. Disturbance torques, including aerodynamic, magnetic, gravity gradient, solar, micrometeorite, debris, collision, and internal torques, will be assessed to quantify the disturbance environment so that the required compensating torques can be determined. The control torques, including passive versus active, momentum control, bias momentum, spin stabilization, dual spin, gravity gradient, magnetic, reaction wheels, control moment gyros, inertia augmentation techniques, three-axis control, and reaction control systems (RCSs), will be considered. Conditions for stability will also be considered.

  6. Industrial linguistic control

    SciTech Connect

    King, R.E.; Karonis, F.

    1983-01-01

    The use of various types of controllers and control techniques for industrial process is discussed. An ongoing research and development project is reported on the application of intelligent linguistic controllers to processes in the cement industry in Greece which have, in the past, been controllable only by human operators. Prototype linguistic controllers using fuzzy logic have been implemented and tested on a rotary kiln precalciner flash furnace (3-input 3-output) and on a cement mill separator (3-input 2-output) with good results. Originally implemented on a supervisory minicomputer, the algorithms have been transferred to microcomputers which form the heart of this class of intelligent linguistic controllers. 6 references.

  7. Aircraft control system

    NASA Technical Reports Server (NTRS)

    Kendall, Greg T. (Inventor); Morgan, Walter R. (Inventor)

    2010-01-01

    A span-loaded, highly flexible flying wing, having horizontal control surfaces mounted aft of the wing on extended beams to form local pitch-control devices. Each of five spanwise wing segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other wing segments, to minimize inter-segment loads. Wing dihedral is controlled by separately controlling the local pitch-control devices consisting of a control surface on a boom, such that inboard and outboard wing segment pitch changes relative to each other, and thus relative inboard and outboard lift is varied.

  8. Robot welding process control

    NASA Technical Reports Server (NTRS)

    Romine, Peter L.

    1991-01-01

    This final report documents the development and installation of software and hardware for Robotic Welding Process Control. Primary emphasis is on serial communications between the CYRO 750 robotic welder, Heurikon minicomputer running Hunter & Ready VRTX, and an IBM PC/AT, for offline programming and control and closed-loop welding control. The requirements for completion of the implementation of the Rocketdyne weld tracking control are discussed. The procedure for downloading programs from the Intergraph, over the network, is discussed. Conclusions are made on the results of this task, and recommendations are made for efficient implementation of communications, weld process control development, and advanced process control procedures using the Heurikon.

  9. Control system design method

    DOEpatents

    Wilson, David G [Tijeras, NM; Robinett, III, Rush D.

    2012-02-21

    A control system design method and concomitant control system comprising representing a physical apparatus to be controlled as a Hamiltonian system, determining elements of the Hamiltonian system representation which are power generators, power dissipators, and power storage devices, analyzing stability and performance of the Hamiltonian system based on the results of the determining step and determining necessary and sufficient conditions for stability of the Hamiltonian system, creating a stable control system based on the results of the analyzing step, and employing the resulting control system to control the physical apparatus.

  10. CONTROL ROD DRIVE

    DOEpatents

    Chapellier, R.A.; Rogers, I.

    1961-06-27

    Accurate and controlled drive for the control rod is from an electric motor. A hydraulic arrangement is provided to balance a piston against which a control rod is urged by the application of fluid pressure. The electric motor drive of the control rod for normal operation is made through the aforementioned piston. In the event scramming is required, the fluid pressure urging the control rod against the piston is relieved and an opposite fluid pressure is applied. The lack of mechanical connection between the electric motor and control rod facilitates the scramming operation.

  11. Programmable Digital Controller

    NASA Technical Reports Server (NTRS)

    Wassick, Gregory J.

    2012-01-01

    An existing three-channel analog servo loop controller has been redesigned for piezoelectric-transducer-based (PZT-based) etalon control applications to a digital servo loop controller. This change offers several improvements over the previous analog controller, including software control over proportional-integral-derivative (PID) parameters, inclusion of other data of interest such as temperature and pressure in the control laws, improved ability to compensate for PZT hysteresis and mechanical mount fluctuations, ability to provide pre-programmed scanning and stepping routines, improved user interface, expanded data acquisition, and reduced size, weight, and power.

  12. Propulsion Controls, 1979. [air breathing engine control

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The state of the art of multivariable engine control is examined in order to determine future needs and problem areas and to establish the appropriate roles of government, industries, and universities in addressing these problems.

  13. Supervisory Control of Networked Control Systems

    DTIC Science & Technology

    2006-01-15

    consisting of 3 Koala robots [Lem06b]. The robots are controlled by MICA2 wireless processor modules. The robots communicate over the MICA2’s...preliminary documentation of a wireless autonomous robotic testbed. The system consists of 3 Koala (K-team Inc.) robots that are controlled by the MICA2...by this project. MICA-KoalaBot Hardware: The Koala robot is an autonomous wheeled vehicle that has 16 infrared (IR) proximity sensors around its

  14. MPC improves reformer control

    SciTech Connect

    Jung, C.S.; Noh, K.K.; Yi, S.; Kim, J.S.; Song, H.K.; Hyun, J.C.

    1995-04-01

    A model predictive control strategy was applied to a synthesis gas reformer of Samsung-BP Chemicals in Korea that produces carbon monoxide and hydrogen from naphtha. A strongly endothermic reaction occurs in a catalytic reformer, and reformer outlet temperature is considered to have the most significant effect on product composition. The newly developed reformer is known to be a cost-effective process operating at high reaction temperatures and low steam-to-carbon ratio, but its drawback is temperature control difficulty due to the use of offgas as a part of the fuel. Without smooth control of the reformer outlet temperature, stable operation of the downstream separation units cannot be expected. Therefore, it is a great challenge to apply a model predictive control technique for tight control of reformer outlet temperature. The paper describes model predictive control, the process advanced control project, computer system architecture, analysis of operating condition, control structure, sampling rate, and disturbance estimation.

  15. Multivariable Control Systems

    DTIC Science & Technology

    1968-01-01

    one). Examples abound of systems with numerous controlled variables, and the modern tendency is toward ever greater utilization of systems and plants of this kind. We call them multivariable control systems (MCS).

  16. Consciousness and cognitive control

    PubMed Central

    Kunde, Wilfried; Reuss, Heiko; Kiesel, Andrea

    2012-01-01

    The implementation or change of information processing routines, known as cognitive control, is traditionally believed to be closely linked to consciousness. It seems that we exert control over our behavior if we know the reasons for, and consequences of, doing so. Recent research suggests, however, that several behavioral phenomena that have been construed as instances of cognitive control can be prompted by events of which actors are not aware. Here we give a brief review of this research, discuss possible reasons for inconsistencies in the empirical evidence, and suggest some lines of future research. Specifically, we suggest to differentiate cognitive control evoked either because of explicit or because of implicit control cues. While the former type of control seems to work outside of awareness, the latter type of control seems to be restricted to consciously registered events that call for control. PMID:22419962

  17. Insensitive control technology development

    NASA Technical Reports Server (NTRS)

    Harvey, C. A.; Pope, R. E.

    1978-01-01

    THe investigation of two insensitive controller synthesis techniques was reported. The finite dimensional inverse approach produces a time varying insensitive controller and/or parameter identifier by constructing inverse functions derived from a finite number of input output pair relationships. The MD/IM concept relies on the information matrix theory that was developed in the estimation and identification field. The MD/IM synthesis technique is based on the hypothesis that minimizing the information matrix will reduce system identifiability and consequently system sensitivity to uncertain parameters. The controllers designed with both techniques were evaluated on a realistic C-5A aircraft flight control problem. Results indicate that the FDI controller is more suited to trajectory type problems because of its time varying nature. The MD/IM controller performed as well as the top-rated controllers of the initial effort and has direct application to aircraft flight control problems.

  18. Aeroelastic structural acoustic control.

    PubMed

    Clark, R L; Frampton, K D

    1999-02-01

    Static, constant-gain, output-feedback control compensators were designed to increase the transmission loss across a panel subjected to mean flow on one surface and a stationary, acoustic half-space on the opposite surface. The multi-input, multi-output control system was based upon the use of an array of colocated transducer pairs. The performance of the static-gain, output-feedback controller was compared to that of the full state-feedback controller using the same control actuator arrays, and was found to yield comparable levels of performance for practical limitations on control effort. Additionally, the resulting static compensators proved to be dissipative in nature, and thus the design varied little as a function of the aeroelastic coupling induced by the fluid-structure interaction under subsonic flow conditions. Several parametric studies were performed, comparing the effects of control-effort penalty as well as the number of transducer pairs used in the control system.

  19. Birth control pill - slideshow

    MedlinePlus

    ... this page: //medlineplus.gov/ency/presentations/100108.htm Birth control pill - series—Normal female anatomy To use the ... to produce a successful pregnancy. To prevent pregnancy, birth control pills affect how these organs normally function. Review ...

  20. Nutrient Control Seminars

    EPA Science Inventory

    These Nutrient Control Seminars will present an extensive state-of-the-technology review of the engineering design and operation of nitrogen and phosphorous control technologies and techniques applied at municipal wastewater treatment plants (WWTPs). These seminars will present ...

  1. Nutrient Control Design Manual

    EPA Science Inventory

    The Nutrient Control Design Manual will present an extensive state-of-the-technology review of the engineering design and operation of nitrogen and phosphorous control technologies and techniques applied at municipal wastewater treatment plants (WWTPs). This manual will present ...

  2. Controlling quantum bits

    NASA Astrophysics Data System (ADS)

    2010-08-01

    Can excitons be used to achieve scalable control of quantum light? Steffen Michaelis de Vasconcellos explained to Nature Photonics that the optoelectrical control of exciton qubits in quantum dots offers great promise.

  3. Solar Control design package

    NASA Technical Reports Server (NTRS)

    1978-01-01

    Information used in the evaluation of design of Solar Control's solar heating and cooling system controller and the Solarstat is given. Some of the information includes system performance specifications, design data brochures, and detailed design drawings.

  4. Scabies: Prevention and Control

    MedlinePlus

    ... Diagnostic Assistance [DPDx] Error processing SSI file Prevention & Control Recommend on Facebook Tweet Share Compartir When a ... avoid outbreaks. Institutional outbreaks can be difficult to control and require a rapid, aggressive, and sustained response. ...

  5. Adaptive Decentralized Control

    DTIC Science & Technology

    1985-04-01

    computational requirements and response time provide strong incentives for the use of distributed control architectures. The basic focus of our research is on...ADCON (for Adaptive Decentralized CONtrol) comes from the following observations about the current status of control theory . An important aspect of...decentralized control of completely known systems still has many unresolved issues and some basic problems are yet to be answered. Under these conditions

  6. Microtron Modelling and Control

    SciTech Connect

    Krist, Pavel; Bila, Jiri

    2010-01-05

    The article describes the design of the mathematical model and automatic control system of the microtron (high frequency cyclic electron accelerator). This type of accelerator was controlled manually till now. The critical values have been set up empirically on the basis of the previous operational experiences. The designed automatic control system with fuzzy controller should increase the accelerated electrons current value and improve the beam stability.

  7. System for controlling apnea

    DOEpatents

    Holzrichter, John F

    2015-05-05

    An implanted stimulation device or air control device are activated by an external radar-like sensor for controlling apnea. The radar-like sensor senses the closure of the air flow cavity, and associated control circuitry signals (1) a stimulator to cause muscles to open the air passage way that is closing or closed or (2) an air control device to open the air passage way that is closing or closed.

  8. Adaptive, predictive controller for optimal process control

    SciTech Connect

    Brown, S.K.; Baum, C.C.; Bowling, P.S.; Buescher, K.L.; Hanagandi, V.M.; Hinde, R.F. Jr.; Jones, R.D.; Parkinson, W.J.

    1995-12-01

    One can derive a model for use in a Model Predictive Controller (MPC) from first principles or from experimental data. Until recently, both methods failed for all but the simplest processes. First principles are almost always incomplete and fitting to experimental data fails for dimensions greater than one as well as for non-linear cases. Several authors have suggested the use of a neural network to fit the experimental data to a multi-dimensional and/or non-linear model. Most networks, however, use simple sigmoid functions and backpropagation for fitting. Training of these networks generally requires large amounts of data and, consequently, very long training times. In 1993 we reported on the tuning and optimization of a negative ion source using a special neural network[2]. One of the properties of this network (CNLSnet), a modified radial basis function network, is that it is able to fit data with few basis functions. Another is that its training is linear resulting in guaranteed convergence and rapid training. We found the training to be rapid enough to support real-time control. This work has been extended to incorporate this network into an MPC using the model built by the network for predictive control. This controller has shown some remarkable capabilities in such non-linear applications as continuous stirred exothermic tank reactors and high-purity fractional distillation columns[3]. The controller is able not only to build an appropriate model from operating data but also to thin the network continuously so that the model adapts to changing plant conditions. The controller is discussed as well as its possible use in various of the difficult control problems that face this community.

  9. Reflective Database Access Control

    ERIC Educational Resources Information Center

    Olson, Lars E.

    2009-01-01

    "Reflective Database Access Control" (RDBAC) is a model in which a database privilege is expressed as a database query itself, rather than as a static privilege contained in an access control list. RDBAC aids the management of database access controls by improving the expressiveness of policies. However, such policies introduce new interactions…

  10. Finite Control in Korean

    ERIC Educational Resources Information Center

    Lee, Kum Young

    2009-01-01

    This thesis explores finite control in Korean. An overview of the previous studies of control shows that the mainstream literature on control has consistently argued that referential dependence between an overt matrix argument and an embedded null subject is characteristic of non-finite clauses which contain a PRO subject. Moreover, although some…

  11. Birth Control Pill

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Pill KidsHealth > For Teens > Birth Control Pill A A A What's in this article? ... español La píldora anticonceptiva What Is It? The birth control pill (also called "the Pill") is a daily ...

  12. Birth Control Patch

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Patch KidsHealth > For Teens > Birth Control Patch A A A What's in this article? ... Much Does It Cost? What Is It? The birth control patch is a thin, beige, 1¾-inch (4½- ...

  13. Birth Control Shot

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Shot KidsHealth > For Teens > Birth Control Shot A A A What's in this article? ... español La inyección anticonceptiva What Is It? The birth control shot is a long-acting form of progesterone, ...

  14. Numerical methods in control

    NASA Astrophysics Data System (ADS)

    Mehrmann, Volker; Xu, Hongguo

    2000-11-01

    We study classical control problems like pole assignment, stabilization, linear quadratic control and H[infinity] control from a numerical analysis point of view. We present several examples that show the difficulties with classical approaches and suggest reformulations of the problems in a more general framework. We also discuss some new algorithmic approaches.

  15. Spacecraft nonlinear control

    NASA Technical Reports Server (NTRS)

    Sheen, Jyh-Jong; Bishop, Robert H.

    1992-01-01

    The feedback linearization technique is applied to the problem of spacecraft attitude control and momentum management with control moment gyros (CMGs). The feedback linearization consists of a coordinate transformation, which transforms the system to a companion form, and a nonlinear feedback control law to cancel the nonlinear dynamics resulting in a linear equivalent model. Pole placement techniques are then used to place the closed-loop poles. The coordinate transformation proposed here evolves from three output functions of relative degree four, three, and two, respectively. The nonlinear feedback control law is presented. Stability in a neighborhood of a controllable torque equilibrium attitude (TEA) is guaranteed and this fact is demonstrated by the simulation results. An investigation of the nonlinear control law shows that singularities exist in the state space outside the neighborhood of the controllable TEA. The nonlinear control law is simplified by a standard linearization technique and it is shown that the linearized nonlinear controller provides a natural way to select control gains for the multiple-input, multiple-output system. Simulation results using the linearized nonlinear controller show good performance relative to the nonlinear controller in the neighborhood of the TEA.

  16. Control of Extrusion

    NASA Astrophysics Data System (ADS)

    Zhuromskii, V. M.

    2016-03-01

    The principle and engineering of a system for automatic control of the tension of the thread and the productivity of the process of extrusion of polyacrylonitrile fibers have been presented. The control system is based on the use of functional features of a modern frequency controlled electric drive.

  17. Birth Control Patch

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Patch KidsHealth > For Teens > Birth Control Patch Print A A A What's in this ... Much Does It Cost? What Is It? The birth control patch is a thin, beige, 1¾-inch (4½- ...

  18. Birth Control Shot

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Shot KidsHealth > For Teens > Birth Control Shot Print A A A What's in this ... español La inyección anticonceptiva What Is It? The birth control shot is a long-acting form of progesterone, ...

  19. Birth Control Pill

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Pill KidsHealth > For Teens > Birth Control Pill Print A A A What's in this ... español La píldora anticonceptiva What Is It? The birth control pill (also called "the Pill") is a daily ...

  20. Birth Control Ring

    MedlinePlus

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Ring KidsHealth > For Teens > Birth Control Ring Print A A A What's in this ... español Anillo vaginal anticonceptivo What Is It? The birth control ring is a soft, flexible, doughnut-shaped ring ...

  1. CAS. Controlled Access Security

    SciTech Connect

    Martinez, B.; Pomeroy, G.

    1989-12-01

    The Security Alarm System is a data acquisition and control system which collects data from intrusion sensors and displays the information in a real-time environment for operators. The Access Control System monitors and controls the movement of personnel with the use of card readers and biometrics hand readers.

  2. Lithography overlay controller formulation

    NASA Astrophysics Data System (ADS)

    Bode, Christopher A.; Toprac, Anthony J.; Edwards, Richard D.; Edgar, Thomas F.

    2000-08-01

    Lithography overlay refers to the measurement of the alignment of successive patterns within the manufacture of semiconductor devices. Control of overlay has become of great importance in semiconductor manufacturing, as the tolerance for overlay error is continually shrinking in order to manufacture next-generation semiconductor products. Run-to-run control has become an attractive solution to many control problems within the industry, including overlay. The term run-to-run control refers to any automated procedure whereby recipe settings are updated between successive process runs in order to keep the process under control. The following discussion will present the formulation of such a controller by examining control of overlay. A brief introduction of overlay will be given, highlighting the control challenge overlay presents. A data management methodology that groups like processes together in order to improve controllability, referred to as control threads, will then be presented. Finally, a discussion of linear model predictive control will show its utility in feedback run-to-run control.

  3. Intermittent Control Systems

    ERIC Educational Resources Information Center

    Montgomery, Thomas L.; And Others

    1975-01-01

    The technique of intermittent control systems for air quality control as developed and used by the Tennessee Valley Authority is investigated. Although controversial, all Tennessee Valley Authority sulfur dioxide elimination programs are scheduled to be operational this year. Existing or anticipated intermittent control systems are identified. (BT)

  4. Controls Considerations for Turbine Active Clearance Control

    NASA Technical Reports Server (NTRS)

    Melcher, Kevin J.

    2004-01-01

    This presentation discusses active control of turbine tip clearance from a control systems perspective. It is a subset of charts that were presented at the 2003 meeting of the International Society of Air Breathing Engines which was held August 31 through September 5 in Cleveland, Ohio. The associated reference paper is cited at the end of the presentation. The presentation describes active tip clearance control research being conducted by NASA to improve turbine engine systems. The target application for this effort is commercial aircraft engines. However, it is believed that the technologies developed as part of this research will benefit a broad spectrum of current and future turbomachinery. The first part of the presentation discusses the concept of tip clearance, problems associated with it, and the benefits of controlling it. It lays out a framework for implementing tip clearance controls that enables the implementation to progress from purely analytical to hardware-in-the-loop to fully experimental. And it briefly discusses how the technologies developed will be married to the previously described ACC Test Rig for hardware-in-the-loop demonstrations. The final portion of the presentation, describes one of the key technologies in some detail by presenting equations and results for a functional dynamic model of the tip clearance phenomena. As shown, the model exhibits many of the clearance dynamics found in commercial gas turbine engines. However, initial attempts to validate the model identified limitations that are being addressed to make the model more realistic.

  5. Arbitrating Control of Control and Display Units

    NASA Technical Reports Server (NTRS)

    Sugden, Paul C.

    2007-01-01

    The ARINC 739 Switch is a computer program that arbitrates control of two multi-function control and display units (MCDUs) between (1) a commercial flight-management computer (FMC) and (2) NASA software used in research on transport aircraft. (MCDUs are the primary interfaces between pilots and FMCs on many commercial aircraft.) This program was recently redesigned into a software library that can be embedded in research application programs. As part of the redesign, this software was combined with software for creating custom pages of information to be displayed on a CDU. This software commands independent switching of the left (pilot s) and right (copilot s) MCDUs. For example, a custom CDU page can control the left CDU while the FMC controls the right CDU. The software uses menu keys to switch control of the CDU between the FMC or a custom CDU page. The software provides an interface that enables custom CDU pages to insert keystrokes into the FMC s CDU input interface. This feature allows the custom CDU pages to manipulate the FMC as if it were a pilot.

  6. Control of wastewater using multivariate control chart

    NASA Astrophysics Data System (ADS)

    Nugraha, Jaka; Fatimah, Is; Prabowo, Rino Galang

    2017-03-01

    Wastewater treatment is a crucial process in industry cause untreated or improper treatment of wastewater may leads some problems affecting to the other parts of environmental aspects. For many kinds of wastewater treatments, the parameters of Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), and the Total Suspend Solid (TSS) are usual parameters to be controlled as a standard. In this paper, the application of multivariate Hotteling T2 Individual was reported to control wastewater treatment. By using wastewater treatment data from PT. ICBP, east Java branch, while the fulfillment of quality standards are based on East Java Governor Regulation No. 72 Year 2013 on Standards of Quality of Waste Water Industry and / or Other Business Activities. The obtained results are COD and TSS has a correlation with BOD values with the correlation coefficient higher than 50%, and it is is also found that influence of the COD and TSS to BOD values are 82% and 1.9% respectively. Based on Multivariate control chart Individual T2 Hotteling, it is found that BOD-COD and BOD-TSS are each one subgroup that are outside the control limits. Thus, it can be said there is a process that is not multivariate controlled, but univariately the variables of BOD, COD and TSS are within specification (standard quality) that has been determined.

  7. Magnetically Controlled Variable Transformer

    NASA Technical Reports Server (NTRS)

    Kleiner, Charles T.

    1994-01-01

    Improved variable-transformer circuit, output voltage and current of which controlled by use of relatively small current supplied at relatively low power to control windings on its magnetic cores. Transformer circuits of this type called "magnetic amplifiers" because ratio between controlled output power and power driving control current of such circuit large. This ratio - power gain - can be as large as 100 in present circuit. Variable-transformer circuit offers advantages of efficiency, safety, and controllability over some prior variable-transformer circuits.

  8. Intelligent Control Systems Research

    NASA Technical Reports Server (NTRS)

    Loparo, Kenneth A.

    1994-01-01

    Results of a three phase research program into intelligent control systems are presented. The first phase looked at implementing the lowest or direct level of a hierarchical control scheme using a reinforcement learning approach assuming no a priori information about the system under control. The second phase involved the design of an adaptive/optimizing level of the hierarchy and its interaction with the direct control level. The third and final phase of the research was aimed at combining the results of the previous phases with some a priori information about the controlled system.

  9. Control and optimization system

    DOEpatents

    Xinsheng, Lou

    2013-02-12

    A system for optimizing a power plant includes a chemical loop having an input for receiving an input parameter (270) and an output for outputting an output parameter (280), a control system operably connected to the chemical loop and having a multiple controller part (230) comprising a model-free controller. The control system receives the output parameter (280), optimizes the input parameter (270) based on the received output parameter (280), and outputs an optimized input parameter (270) to the input of the chemical loop to control a process of the chemical loop in an optimized manner.

  10. STOVL Control Integration Program

    NASA Technical Reports Server (NTRS)

    Weiss, C.; Mcdowell, P.; Watts, S.

    1994-01-01

    An integrated flight/propulsion control for an advanced vector thrust supersonic STOVL aircraft, was developed by Pratt & Whitney and McDonnell Douglas Aerospace East. The IFPC design was based upon the partitioning of the global requirements into flight control and propulsion control requirements. To validate the design, aircraft and engine models were also developed for use on a NASA Ames piloted simulator. Different flight control implementations, evaluated for their handling qualities, are documented in the report along with the propulsion control, engine model, and aircraft model.

  11. Water heater control module

    SciTech Connect

    Hammerstrom, Donald J

    2013-11-26

    An advanced electric water heater control system that interfaces with a high temperature cut-off thermostat and an upper regulating thermostat. The system includes a control module that is electrically connected to the high-temperature cut-off thermostat and the upper regulating thermostat. The control module includes a switch to open or close the high-temperature cut-off thermostat and the upper regulating thermostat. The control module further includes circuitry configured to control said switch in response to a signal selected from the group of an autonomous signal, a communicated signal, and combinations thereof.

  12. Recursive Deadbeat Controller Design

    NASA Technical Reports Server (NTRS)

    Juang, Jer-Nan; Phan, Minh Q.

    1997-01-01

    This paper presents a recursive algorithm for a deadbeat predictive controller design. The method combines together the concepts of system identification and deadbeat controller designs. It starts with the multi-step output prediction equation and derives the control force in terms of past input and output time histories. The formulation thus derived satisfies simultaneously system identification and deadbeat controller design requirements. As soon as the coefficient matrices are identified satisfying the output prediction equation, no further work is required to compute the deadbeat control gain matrices. The method can be implemented recursively just as any typical recursive system identification techniques.

  13. Intelligent Welding Controller

    NASA Technical Reports Server (NTRS)

    Cook, George E.; Kumar, Ramaswamy; Prasad, Tanuji; Andersen, Kristinn; Barnett, Robert J.

    1989-01-01

    Control system adapts to changing design requirements and operating conditions. Proposed control system for gas/tungsten arc welding requires only that operator specifies such direct parameters of welds as widths and depths of penetration. In control system for robotic welder, components and functions intimately connected with welding process assigned to controller domain. More general functions assigned to supervisor domain. Initial estimate of indirect parameters of welding process applied to system only at beginning of weld (t=0); after start of welding, outputs from multivariable controller takes place of estimate.

  14. Intelligent flight control systems

    NASA Technical Reports Server (NTRS)

    Stengel, Robert F.

    1993-01-01

    The capabilities of flight control systems can be enhanced by designing them to emulate functions of natural intelligence. Intelligent control functions fall in three categories. Declarative actions involve decision-making, providing models for system monitoring, goal planning, and system/scenario identification. Procedural actions concern skilled behavior and have parallels in guidance, navigation, and adaptation. Reflexive actions are spontaneous, inner-loop responses for control and estimation. Intelligent flight control systems learn knowledge of the aircraft and its mission and adapt to changes in the flight environment. Cognitive models form an efficient basis for integrating 'outer-loop/inner-loop' control functions and for developing robust parallel-processing algorithms.

  15. Controls and guidance research

    NASA Technical Reports Server (NTRS)

    Homaifar, Abdollah; Dunn, Derome; Song, Yong-Duan; Lai, Steven H.-Y.

    1992-01-01

    The objectives of the control group are concentrated on research and education. The control problem of the hypersonic space vehicle represents an important and challenging issue in aerospace engineering. The work described in this report is part of our effort in developing advanced control strategies for such a system. In order to achieve the objectives stated in the NASA-CORE proposal, the tasks were divided among the group based upon their educational expertise. Within the educational component we are offering a Linear Systems and Control course for students in electrical and mechanical engineering. Also, we are proposing a new course in Digital Control Systems with a corresponding laboratory.

  16. [Controlling instruments in radiology].

    PubMed

    Maurer, M

    2013-10-01

    Due to the rising costs and competitive pressures radiological clinics and practices are now facing, controlling instruments are gaining importance in the optimization of structures and processes of the various diagnostic examinations and interventional procedures. It will be shown how the use of selected controlling instruments can secure and improve the performance of radiological facilities. A definition of the concept of controlling will be provided. It will be shown which controlling instruments can be applied in radiological departments and practices. As an example, two of the controlling instruments, material cost analysis and benchmarking, will be illustrated.

  17. SPS antenna pointing control

    NASA Technical Reports Server (NTRS)

    Hung, J. C.

    1980-01-01

    The pointing control of a microwave antenna of the Satellite Power System was investigated emphasizing: (1) the SPS antenna pointing error sensing method; (2) a rigid body pointing control design; and (3) approaches for modeling the flexible body characteristics of the solar collector. Accuracy requirements for the antenna pointing control consist of a mechanical pointing control accuracy of three arc-minutes and an electronic phased array pointing accuracy of three arc-seconds. Results based on the factors considered in current analysis, show that the three arc-minute overall pointing control accuracy can be achieved in practice.

  18. Conscious Control over Action.

    PubMed

    Shepherd, Joshua

    2015-06-01

    The extensive involvement of nonconscious processes in human behaviour has led some to suggest that consciousness is much less important for the control of action than we might think. In this article I push against this trend, developing an understanding of conscious control that is sensitive to our best models of overt (that is, bodily) action control. Further, I assess the cogency of various zombie challenges-challenges that seek to demote the importance of conscious control for human agency. I argue that though nonconscious contributions to action control are evidently robust, these challenges are overblown.

  19. CONTROL FOR NEUTRONIC REACTOR

    DOEpatents

    Lichtenberger, H.V.; Cameron, R.A.

    1959-03-31

    S>A control rod operating device in a nuclear reactor of the type in which the control rod is gradually withdrawn from the reactor to a position desired during stable operation is described. The apparatus is comprised essentially of a stop member movable in the direction of withdrawal of the control rod, a follower on the control rod engageable with the stop and means urging the follower against the stop in the direction of withdrawal. A means responsive to disengagement of the follower from the stop is provided for actuating the control rod to return to the reactor shut-down position.

  20. Conscious Control over Action

    PubMed Central

    Shepherd, Joshua

    2015-01-01

    The extensive involvement of nonconscious processes in human behaviour has led some to suggest that consciousness is much less important for the control of action than we might think. In this article I push against this trend, developing an understanding of conscious control that is sensitive to our best models of overt (that is, bodily) action control. Further, I assess the cogency of various zombie challenges—challenges that seek to demote the importance of conscious control for human agency. I argue that though nonconscious contributions to action control are evidently robust, these challenges are overblown. PMID:26113753

  1. Modeling and control of thermostatically controlled loads

    SciTech Connect

    Backhaus, Scott N; Sinitsyn, Nikolai; Kundu, S.; Hiskens, I.

    2011-01-04

    As the penetration of intermittent energy sources grows substantially, loads will be required to play an increasingly important role in compensating the fast time-scale fluctuations in generated power. Recent numerical modeling of thermostatically controlled loads (TCLs) has demonstrated that such load following is feasible, but analytical models that satisfactorily quantify the aggregate power consumption of a group of TCLs are desired to enable controller design. We develop such a model for the aggregate power response of a homogeneous population of TCLs to uniform variation of all TCL setpoints. A linearized model of the response is derived, and a linear quadratic regulator (LQR) has been designed. Using the TCL setpoint as the control input, the LQR enables aggregate power to track reference signals that exhibit step, ramp and sinusoidal variations. Although much of the work assumes a homogeneous population of TCLs with deterministic dynamics, we also propose a method for probing the dynamics of systems where load characteristics are not well known.

  2. Integrated Biological Control

    SciTech Connect

    JOHNSON, A.R.

    2003-10-09

    Biological control is any activity taken to prevent, limit, clean up, or remediate potential environmental, health and safety, or workplace quality impacts from plants, animals, or microorganisms. At Hanford the principal emphasis of biological control is to prevent the transport of radioactive contamination by biological vectors (plants, animals, or microorganisms), and where necessary, control and clean up resulting contamination. Other aspects of biological control at Hanford include industrial weed control (e.g.; tumbleweeds), noxious weed control (invasive, non-native plant species), and pest control (undesirable animals such as rodents and stinging insects, and microorganisms such as molds that adversely affect the quality of the workplace environment). Biological control activities may be either preventive (a priori) or in response to existing contamination spread (a posteriori). Surveillance activities, including ground, vegetation, flying insect, and other surveys, and a priori control actions, such as herbicide spraying and placing biological barriers, are important in preventing radioactive contamination spread. If surveillance discovers that biological vectors have spread radioactive contamination, a posteriori control measures, such as fixing contamination, followed by cleanup and removal of the contamination to an approved disposal location are typical response functions. In some cases remediation following the contamination cleanup and removal is necessary. Biological control activities for industrial weeds, noxious weeds and pests have similar modes of prevention and response.

  3. Integrated Biological Control

    SciTech Connect

    JOHNSON, A.R.

    2002-09-01

    Biological control is any activity taken to prevent, limit, clean up, or remediate potential environmental, health and safety, or workplace quality impacts from plants, animals, or microorganisms. At Hanford the principal emphasis of biological control is to prevent the transport of radioactive contamination by biological vectors (plants, animals, or microorganisms), and where necessary, control and clean up resulting contamination. Other aspects of biological control at Hanford include industrial weed control (e.g.; tumbleweeds), noxious weed control (invasive, non-native plant species), and pest control (undesirable animals such as rodents and stinging insects; and microorganisms such as molds that adversely affect the quality of the workplace environment). Biological control activities may be either preventive (apriori) or in response to existing contamination spread (aposteriori). Surveillance activities, including ground, vegetation, flying insect, and other surveys, and apriori control actions, such as herbicide spraying and placing biological barriers, are important in preventing radioactive contamination spread. If surveillance discovers that biological vectors have spread radioactive contamination, aposteriori control measures, such as fixing contamination, followed by cleanup and removal of the contamination to an approved disposal location are typical response functions. In some cases remediation following the contamination cleanup and removal is necessary. Biological control activities for industrial weeds, noxious weeds and pests have similar modes of prevention and response.

  4. Controlling chaos faster

    SciTech Connect

    Bick, Christian; Kolodziejski, Christoph; Timme, Marc

    2014-09-01

    Predictive feedback control is an easy-to-implement method to stabilize unknown unstable periodic orbits in chaotic dynamical systems. Predictive feedback control is severely limited because asymptotic convergence speed decreases with stronger instabilities which in turn are typical for larger target periods, rendering it harder to effectively stabilize periodic orbits of large period. Here, we study stalled chaos control, where the application of control is stalled to make use of the chaotic, uncontrolled dynamics, and introduce an adaptation paradigm to overcome this limitation and speed up convergence. This modified control scheme is not only capable of stabilizing more periodic orbits than the original predictive feedback control but also speeds up convergence for typical chaotic maps, as illustrated in both theory and application. The proposed adaptation scheme provides a way to tune parameters online, yielding a broadly applicable, fast chaos control that converges reliably, even for periodic orbits of large period.

  5. On the Switching Control

    NASA Astrophysics Data System (ADS)

    Balas, Valentina E.; Balas, Marius M.

    2009-04-01

    The paper is discussing the measures able to reject the instability that may unexpectedly appear in particular conditions, in switching controllers applications. The switching controllers' effect is explained by the combined effects of the unsuitable choice of the switching moments (in the first or third quadrants of the phase trajectory of the switching error) and of the temporal aliasing that can distort the digital control systems when the sampling rate is close to the frequency of the oscillations that are produced by the commutation. The correct switching moments are located into the second and fourth quadrants of the phase trajectory of the switching error, but an active preparation of the commutation may be simply achieved by using a tracking controller, that is driving the output of open loop controller to follow the output of the close loop controller, permanently minimizing the switching error. Simulations issued from a dc driver speed controller and from an aircraft are provided.

  6. CRUCIFORM CONTROL ROD JOINT

    DOEpatents

    Thorp, A.G. II

    1962-08-01

    An invention is described which relates to nuclear reactor control rod components and more particularly to a joint between cruciform control rod members and cruciform control rod follower members. In one embodiment this invention provides interfitting crossed arms at adjacent ends of a control rod and its follower in abutting relation. This holds the members against relative opposite longitudinal movement while a compression member keys the arms against relative opposite rotation around a common axis. Means are also provided for centering the control rod and its follower on a common axis and for selectively releasing the control rod from its follower for the insertion of a replacement of the control rod and reuse of the follower. (AEC)

  7. Controlling chaos faster.

    PubMed

    Bick, Christian; Kolodziejski, Christoph; Timme, Marc

    2014-09-01

    Predictive feedback control is an easy-to-implement method to stabilize unknown unstable periodic orbits in chaotic dynamical systems. Predictive feedback control is severely limited because asymptotic convergence speed decreases with stronger instabilities which in turn are typical for larger target periods, rendering it harder to effectively stabilize periodic orbits of large period. Here, we study stalled chaos control, where the application of control is stalled to make use of the chaotic, uncontrolled dynamics, and introduce an adaptation paradigm to overcome this limitation and speed up convergence. This modified control scheme is not only capable of stabilizing more periodic orbits than the original predictive feedback control but also speeds up convergence for typical chaotic maps, as illustrated in both theory and application. The proposed adaptation scheme provides a way to tune parameters online, yielding a broadly applicable, fast chaos control that converges reliably, even for periodic orbits of large period.

  8. Robust Control Design for Flight Control

    DTIC Science & Technology

    1989-07-01

    to achieve desired performance over the full flight envelope when linear feedback is employed. Exact linearization methods [48] provide means for...designing nonlinear feedback laws which satisfy these requirements. However, exact linearization is not always compatible with control authority...specific situations. The most promising approaches appear to be those associated with methods of exact linearization . This procedure is based on some

  9. Flight control actuation system

    NASA Technical Reports Server (NTRS)

    Wingett, Paul T. (Inventor); Gaines, Louie T. (Inventor); Evans, Paul S. (Inventor); Kern, James I. (Inventor)

    2006-01-01

    A flight control actuation system comprises a controller, electromechanical actuator and a pneumatic actuator. During normal operation, only the electromechanical actuator is needed to operate a flight control surface. When the electromechanical actuator load level exceeds 40 amps positive, the controller activates the pneumatic actuator to offset electromechanical actuator loads to assist the manipulation of flight control surfaces. The assistance from the pneumatic load assist actuator enables the use of an electromechanical actuator that is smaller in size and mass, requires less power, needs less cooling processes, achieves high output forces and adapts to electrical current variations. The flight control actuation system is adapted for aircraft, spacecraft, missiles, and other flight vehicles, especially flight vehicles that are large in size and travel at high velocities.

  10. Unpacking Self-Control

    PubMed Central

    Duckworth, Angela; Steinberg, Laurence

    2014-01-01

    Self-controlled behavior refers to actions aligned with valued, longer-term goals in the face of conflicting impulses to seek immediate gratification. In this article, we argue that the psychological processes that contribute to self-controlled behavior can be grouped into two functionally distinct categories: Volitional processes facilitate self-controlled behavior and include executive functions as well as learned metacognitive strategies like planning, attention deployment, and psychological distancing. In contrast, impulsigenic processes undermine self-controlled behavior and include reward sensitivity, sensation seeking, and domain-specific cravings. A disproportionate amount of research has addressed the former at the expense of understanding individual and developmental differences in the latter. This imbalance is now being rectified. Distinguishing between self-controlled behavior and its antecedent psychological processes helps illuminate normative developmental changes in self-control and points to directions for measurement and intervention. PMID:25821515

  11. Advanced Aerodynamic Control Effectors

    NASA Technical Reports Server (NTRS)

    Wood, Richard M.; Bauer, Steven X. S.

    1999-01-01

    A 1990 research program that focused on the development of advanced aerodynamic control effectors (AACE) for military aircraft has been reviewed and summarized. Data are presented for advanced planform, flow control, and surface contouring technologies. The data show significant increases in lift, reductions in drag, and increased control power, compared to typical aerodynamic designs. The results presented also highlighted the importance of planform selection in the design of a control effector suite. Planform data showed that dramatic increases in lift (greater than 25%) can be achieved with multiple wings and a sawtooth forebody. Passive porosity and micro drag generator control effector data showed control power levels exceeding that available from typical effectors (moving surfaces). Application of an advanced planform to a tailless concept showed benefits of similar magnitude as those observed in the generic studies.

  12. Fuzzy logic controller optimization

    DOEpatents

    Sepe, Jr., Raymond B; Miller, John Michael

    2004-03-23

    A method is provided for optimizing a rotating induction machine system fuzzy logic controller. The fuzzy logic controller has at least one input and at least one output. Each input accepts a machine system operating parameter. Each output produces at least one machine system control parameter. The fuzzy logic controller generates each output based on at least one input and on fuzzy logic decision parameters. Optimization begins by obtaining a set of data relating each control parameter to at least one operating parameter for each machine operating region. A model is constructed for each machine operating region based on the machine operating region data obtained. The fuzzy logic controller is simulated with at least one created model in a feedback loop from a fuzzy logic output to a fuzzy logic input. Fuzzy logic decision parameters are optimized based on the simulation.

  13. Designing Genetic Feedback Controllers.

    PubMed

    Harris, Andreas W K; Dolan, James A; Kelly, Ciarán L; Anderson, James; Papachristodoulou, Antonis

    2015-08-01

    By incorporating feedback around systems we wish to manipulate, it is possible to improve their performance and robustness properties to meet pre-specified design objectives. For decades control engineers have been successfully implementing feedback controllers for complex mechanical and electrical systems such as aircraft and sports cars. Natural biological systems use feedback extensively for regulation and adaptation but apart from the most basic designs, there is no systematic framework for designing feedback controllers in Synthetic Biology. In this paper we describe how classical approaches from linear control theory can be used to close the loop. This includes the design of genetic circuits using feedback control and the presentation of a biological phase lag controller.

  14. Flight control actuation system

    NASA Technical Reports Server (NTRS)

    Wingett, Paul T. (Inventor); Gaines, Louie T. (Inventor); Evans, Paul S. (Inventor); Kern, James I. (Inventor)

    2004-01-01

    A flight control actuation system comprises a controller, electromechanical actuator and a pneumatic actuator. During normal operation, only the electromechanical actuator is needed to operate a flight control surface. When the electromechanical actuator load level exceeds 40 amps positive, the controller activates the pneumatic actuator to offset electromechanical actuator loads to assist the manipulation of flight control surfaces. The assistance from the pneumatic load assist actuator enables the use of an electromechanical actuator that is smaller in size and mass, requires less power, needs less cooling processes, achieves high output forces and adapts to electrical current variations. The flight control actuation system is adapted for aircraft, spacecraft, missiles, and other flight vehicles, especially flight vehicles that are large in size and travel at high velocities.

  15. Chimpanzee Cognitive Control

    PubMed Central

    Beran, Michael J.

    2015-01-01

    Cognitive control processes are a feature of human cognition. Recent comparative tests have shown that some nonhuman animals also might share aspects of cognitive control with humans. Two of the executive processes that constitute cognitive control are metacognition and self-control, and recent experiments with chimpanzees are described that demonstrate metacognitive monitoring and control when these animals engage in an information-seeking task. Chimpanzees also show strategic responding in a self-control task by exhibiting self-distraction as an aid to delay of gratification. These demonstrations indicate continuity with similar human cognitive capacities, and the performances of chimpanzees in these kinds of tests have implications for considering the nature of the intelligence of these animals. PMID:26478660

  16. Nuclear reactor control

    DOEpatents

    Cawley, William E.; Warnick, Robert F.

    1982-01-01

    1. In a nuclear reactor incorporating a plurality of columns of tubular fuel elements disposed in horizontal tubes in a mass of graphite wherein water flows through the tubes to cool the fuel elements, the improvement comprising at least one control column disposed in a horizontal tube including fewer fuel elements than in a normal column of fuel elements and tubular control elements disposed at both ends of said control column, and means for varying the horizontal displacement of the control column comprising a winch at the upstream end of the control column and a cable extending through the fuel and control elements and attached to the element at the downstream end of the column.

  17. Computer aided manipulator control

    NASA Technical Reports Server (NTRS)

    Bejczy, A. K.; Zawacki, R. L.

    1980-01-01

    This paper describes the hardware and software system of a dedicated mini- and microcomputer network developed at the JPL teleoperator project to aid the operator in real-time control of remote manipulators. The operator can be in series or in parallel with the control computer during operation. The purpose of the project is to develop, demonstrate and evaluate advanced supervisory control concepts and techniques for space applications. The paper concludes with a brief outline of future development plans and issues.

  18. Adaptive hierarchical fuzzy controller

    SciTech Connect

    Raju, G.V.S.; Jun Zhou

    1993-07-01

    A methodology for designing adaptive hierarchical fuzzy controllers is presented. In order to evaluate this concept, several suitable performance indices were developed and converted to linguistic fuzzy variables. Based on those variables, a supervisory fuzzy rule set was constructed and used to change the parameters of a hierarchical fuzzy controller to accommodate the variations of system parameters. The proposed algorithm was used in feedwater flow control to a steam generator. Simulation studies are presented that illustrate the effectiveness of the approach

  19. Supervisory control systems

    NASA Technical Reports Server (NTRS)

    Sheridan, T. B.

    1974-01-01

    The various functions of a computer are considered that serve in connecting the man, with his displays and controls, to an external environment, manipulator activators and the interoceptors that are in the actuators, and to the interosensors and the motors or the actuators to drive the sensors. Projected is an improved exoskeleton mechanism with computer control and some supervisory control that may give a quadriplegic the ability to walk and run around.

  20. Modular Battery Controller

    NASA Technical Reports Server (NTRS)

    Button, Robert M (Inventor); Gonzalez, Marcelo C (Inventor)

    2017-01-01

    Some embodiments of the present invention describe a battery including a plurality of master-less controllers. Each controller is operatively connected to a corresponding cell in a string of cells, and each controller is configured to bypass a fraction of current around the corresponding cell when the corresponding cell has a greater charge than one or more other cells in the string of cells.

  1. Rotor control system

    NASA Technical Reports Server (NTRS)

    Bradford, Michael P. (Inventor); Maciolek, Joseph R. (Inventor)

    1987-01-01

    A helicopter rotor control system (13) including a stop azimuth controller (32) for establishing the value of a deceleration command (15') to a deceleration controller (23), a transition azimuth predictor (41) and a position reference generator (55), which are effective during the last revolution of said rotor (14) to establish a correction indication (38) to adjust the deceleration command (15') to ensure that one of the rotor blades (27) stops at a predetermined angular position.

  2. JPRS Report, Arms Control

    DTIC Science & Technology

    2007-11-02

    dangerous because the measure of control by central political organs of the state over conventional weapons and their military use is substan...It is always under the control and guidance of governments of the interested parties, it is the most manageable and has the least inertia. It...JPRS-TAC-89-001 10 JANUARY 1989 —JPRS Report— Arms Control nTSTRJBUTlON STATEMfcwTA Approved for public release; Distribution Unlimited n

  3. Innovation for Pollution Control

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Kinetic Controls Inc.'s refuse-fired steam generating facility led to the development of an air pollution equipment control device. The device is currently marketed by two NASA/Langley Research Center employees. It automatically senses and compensates for the changes in smoke composition when refuse is used as a fuel by adjusting the precipitator's voltage and current to permit maximum collection of electrically charged dust particles. The control adapts to any electrostatic precipitator and should have extensive commercial applications.

  4. Bimodality in Network Control

    NASA Astrophysics Data System (ADS)

    Jia, Tao; Liu, Yang-Yu; Posfai, Marton; Slotine, Jean-Jacques; Barabasi, Albert-Laszlo

    2013-03-01

    Controlling complex systems is a fundamental challenge of network science. Recent tools enable us to identify the minimum driver nodes, from which we can control a system. They also indicate a multiplicity of minimum driver node sets (MDS's): multiple combinations of the same number of nodes can achieve control over the system. This multiplicity allows us to classify individual nodes as critical if they are involved in all control configurations, intermittent if they occasionally act as driver nodes and redundant if they do not play any role in control. We develop computational and analytical framework analyzing nodes in each category in both model and real networks. We find that networks with identical degree distribution can be in two distinct control modes, ``centralized'' or ``distributed'', with drastic change on the role of each node in maintaining the controllability and orders of magnitude difference in the number of MDS's. In analyzing both model and real networks, we find that the two modes can be inferred directly from the network's degree distribution. Finally we show that the two control modes can be switched by small structural perturbations, leading to potential applications of control theory in real systems.

  5. Control system design guide

    SciTech Connect

    Sellers, David; Friedman, Hannah; Haasl, Tudi; Bourassa, Norman; Piette, Mary Ann

    2003-05-01

    The ''Control System Design Guide'' (Design Guide) provides methods and recommendations for the control system design process and control point selection and installation. Control systems are often the most problematic system in a building. A good design process that takes into account maintenance, operation, and commissioning can lead to a smoothly operating and efficient building. To this end, the Design Guide provides a toolbox of templates for improving control system design and specification. HVAC designers are the primary audience for the Design Guide. The control design process it presents will help produce well-designed control systems that achieve efficient and robust operation. The spreadsheet examples for control valve schedules, damper schedules, and points lists can streamline the use of the control system design concepts set forth in the Design Guide by providing convenient starting points from which designers can build. Although each reader brings their own unique questions to the text, the Design Guide contains information that designers, commissioning providers, operators, and owners will find useful.

  6. Detonation command and control

    DOEpatents

    Mace, Jonathan L.; Seitz, Gerald J.; Echave, John A.; Le Bas, Pierre-Yves

    2015-11-10

    The detonation of one or more explosive charges and propellant charges by a detonator in response to a fire control signal from a command and control system comprised of a command center and instrumentation center with a communications link therebetween. The fire control signal is selectively provided to the detonator from the instrumentation center if plural detonation control switches at the command center are in a fire authorization status, and instruments, and one or more interlocks, if included, are in a ready for firing status. The instrumentation and command centers are desirably mobile, such as being respective vehicles.

  7. Optimal control computer programs

    NASA Technical Reports Server (NTRS)

    Kuo, F.

    1992-01-01

    The solution of the optimal control problem, even with low order dynamical systems, can usually strain the analytical ability of most engineers. The understanding of this subject matter, therefore, would be greatly enhanced if a software package existed that could simulate simple generic problems. Surprisingly, despite a great abundance of commercially available control software, few, if any, address the part of optimal control in its most generic form. The purpose of this paper is, therefore, to present a simple computer program that will perform simulations of optimal control problems that arise from the first necessary condition and the Pontryagin's maximum principle.

  8. The ISOLDE control system

    NASA Astrophysics Data System (ADS)

    Deloose, I.; Pace, A.

    1994-12-01

    The two CERN isotope separators named ISOLDE have been running on the new Personal Computer (PC) based control system since April 1992. The new architecture that makes heavy use of the commercial software and hardware of the PC market has been implemented on the 1700 geographically distributed control channels of the two separators and their experimental area. Eleven MSDOS Intel-based PCs with approximately 80 acquisition and control boards are used to access the equipment and are controlled from three PCs running Microsoft Windows used as consoles through a Novell Local Area Network. This paper describes the interesting solutions found and discusses the reduced programming workload and costs that have been obtained.

  9. SSRF Beamline Control System

    SciTech Connect

    Zheng, L. F.; Liu, P.; Zhang, Z. H.; Hu, C.; Mi, Q. R.; Wu, Y. F.; Gong, P. R.; Zhu, Z. X.; Li, Z.

    2010-06-23

    There are seven beamlines in the Phase-I of SSRF. Five of them are equipped with Insertion Devices, while two with Bending Magnets. The beamline control system is based on the standard hardware and software architecture. The VME(PowerPC) with VxWorks is used for motion control, while the personal computers with Scientific Linux are the front end controllers of equipment protection and personnel safety systems. The control software is developed under EPICS which makes various experimental programs of Blu-Ice, LabView, VC and SPEC conveniently access Monochromators, mirror chambers and other optical components.

  10. Cooled, temperature controlled electrometer

    DOEpatents

    Morgan, John P.

    1992-08-04

    A cooled, temperature controlled electrometer for the measurement of small currents. The device employs a thermal transfer system to remove heat from the electrometer circuit and its environment and dissipate it to the external environment by means of a heat sink. The operation of the thermal transfer system is governed by a temperature regulation circuit which activates the thermal transfer system when the temperature of the electrometer circuit and its environment exceeds a level previously inputted to the external variable temperature control circuit. The variable temperature control circuit functions as subpart of the temperature control circuit. To provide temperature stability and uniformity, the electrometer circuit is enclosed by an insulated housing.

  11. Cooled, temperature controlled electrometer

    DOEpatents

    Morgan, John P.

    1992-01-01

    A cooled, temperature controlled electrometer for the measurement of small currents. The device employs a thermal transfer system to remove heat from the electrometer circuit and its environment and dissipate it to the external environment by means of a heat sink. The operation of the thermal transfer system is governed by a temperature regulation circuit which activates the thermal transfer system when the temperature of the electrometer circuit and its environment exceeds a level previously inputted to the external variable temperature control circuit. The variable temperature control circuit functions as subpart of the temperature control circuit. To provide temperature stability and uniformity, the electrometer circuit is enclosed by an insulated housing.

  12. MOSFET Power Controller

    NASA Technical Reports Server (NTRS)

    Mitchell, J.; Jones, K.

    1986-01-01

    High current and voltage controlled remotely. Remote Power Conroller includes two series-connected banks of parallel-connected MOSFET's to withstand high current and voltage. Voltage sharing between switch banks, low-impedance, gate-drive circuits used. Provided controlled range for turn on. Individually trimmable to insure simultaneous switching within few nanoseconds during both turn on and turn off. Control circuit for each switch bank and over-current trip circuit float independently and supplied power via transformer T1 from inverter. Control of floating stages by optocouplers.

  13. Satellite attitude control simulations

    NASA Technical Reports Server (NTRS)

    Debra, D. B.; Powell, J. D.

    1973-01-01

    Work was conducted to develop an extremely low drift rate gyroscope and a very precise star tracker. A proposed relativity satellite will measure very accurately the theoretically predicted 'relativistic' precession of the gyroscope relative to an inertial reference frame provided by the star tracker. Aspects of precision spinning attitude control are discussed together with questions of gyro operation, and the hopping mode for lunar transportation. For the attitude control system of the lunar hopper, a number of control laws were investigated. The studies indicated that some suboptimal controls should be adequate for the system.

  14. Optimal Linear Control.

    DTIC Science & Technology

    1979-12-01

    OPTIMAL LINEAR CONTROL C.A. HARVEY M.G. SAFO NOV G. STEIN J.C. DOYLE HONEYWELL SYSTEMS & RESEARCH CENTER j 2600 RIDGWAY PARKWAY j [ MINNEAPOLIS...RECIPIENT’S CAT ALC-’ W.IMIJUff’? * J~’ CR2 15-238-4F TP P EI)ŕll * (~ Optimal Linear Control ~iOGRPR UBA m a M.G Lnar o Con_ _ _ _ _ _ R PORT__ _ _ I RE...Characterizations of optimal linear controls have been derived, from which guides for selecting the structure of the control system and the weights in

  15. Helicopter high gain control

    NASA Technical Reports Server (NTRS)

    Cunningham, T. B.; Nunn, E. C.

    1979-01-01

    High gain control is explored through a design study of the CH-47B helicopter. The plans are designed to obtain the maximum bandwidth possible given the hardware constraints. Controls are designed with modal control theory to specific bandwidths and closed loop mode shapes. Comparisons are made to an earlier complementary filter approach. Bandwidth improvement by removal of limitations is explored in order to establish hardware and mechanization options. Improvements in the pitch axis control system and in the rate gyro sensor noise characteristics in all axes are discussed. The use of rotor state feedback is assessed.

  16. Controlled wind motor

    SciTech Connect

    Boswell, F.A.

    1983-12-27

    A mechanical sail including a rotatable mast, the mast including a top vane mount and a bottom vane mount, the mounts being spaced from each other on the mast and rotatable therewith, a series of rotatable vanes spaced from and surrounding the mast and supported by and between the mounts, cam operaters extending between the mounts and connected to the vanes for controlling the rotation of the vanes, a first controller associated with the mast below the bottom vane mount for controlling the cam operators, the first controller being movable vertically with respect to the mast, a second controller for moving the first controller vertically with respect to the mast, the vanes being flexible and bowed outwardly, the bottom vane mount being movable with respect to the mast and connected to the second controller whereby when the second controller is operated, the bottom vane mount will move toward the top vane mount causing the vanes to bow outwardly at a desired arc and whereby when the first controller is moved, the vanes are caused to rotate to the desired angle of attack with respect to wind velocity and direction. When the sail is connected to a motor drive, the vessel may be driven forward or rearward depending on the angle of attack of the vanes through 180/sup 0/.

  17. Detonation command and control

    DOEpatents

    Mace, Jonathan L.; Seitz, Gerald J.; Echave, John A.; Le Bas, Pierre-Yves

    2016-05-31

    The detonation of one or more explosive charges and propellant charges by a detonator in response to a fire control signal from a command and control system comprised of a command center and instrumentation center with a communications link there between. The fire control signal is selectively provided to the detonator from the instrumentation center if plural detonation control switches at the command center are in a fire authorization status, and instruments, and one or more interlocks, if included, are in a ready for firing status. The instrumentation and command centers are desirably mobile, such as being respective vehicles.

  18. Device Oriented Project Controller

    SciTech Connect

    Dalesio, Leo; Kraimer, Martin

    2013-11-20

    This proposal is directed at the issue of developing control systems for very large HEP projects. A de-facto standard in accelerator control is the Experimental Physics and Industrial Control System (EPICS), which has been applied successfully to many physics projects. EPICS is a channel based system that requires that each channel of each device be configured and controlled. In Phase I, the feasibility of a device oriented extension to the distributed channel database was demonstrated by prototyping a device aware version of an EPICS I/O controller that functions with the current version of the channel access communication protocol. Extensions have been made to the grammar to define the database. Only a multi-stage position controller with limit switches was developed in the demonstration, but the grammar should support a full range of functional record types. In phase II, a full set of record types will be developed to support all existing record types, a set of process control functions for closed loop control, and support for experimental beam line control. A tool to configure these records will be developed. A communication protocol will be developed or extensions will be made to Channel Access to support introspection of components of a device. Performance bench marks will be made on both communication protocol and the database. After these records and performance tests are under way, a second of the grammar will be undertaken.

  19. Control of robot dynamics using acceleration control

    NASA Technical Reports Server (NTRS)

    Workman, G. L.; Prateru, S.; Li, W.; Hinman, Elaine

    1992-01-01

    Acceleration control of robotic devices can provide improvements to many space-based operations using flexible manipulators and to ground-based operations requiring better precision and efficiency than current industrial robots can provide. This paper reports on a preliminary study of acceleration measurement on robotic motion during parabolic flights on the NASA KC-135 and a parallel study of accelerations with and without gravity arising from computer simulated motions using TREETOPS software.

  20. Controls for space structures

    NASA Astrophysics Data System (ADS)

    Balas, Mark

    1991-11-01

    Assembly and operation of large space structures (LSS) in orbit will require robot-assisted docking and berthing of partially-assembled structures. These operations require new solutions to the problems of controls. This is true because of large transient and persistent disturbances, controller-structure interaction with unmodeled modes, poorly known structure parameters, slow actuator/sensor dynamical behavior, and excitation of nonlinear structure vibrations during control and assembly. For on-orbit assembly, controllers must start with finite element models of LSS and adapt on line to the best operating points, without compromising stability. This is not easy to do, since there are often unmodeled dynamic interactions between the controller and the structure. The indirect adaptive controllers are based on parameter estimation. Due to the large number of modes in LSS, this approach leads to very high-order control schemes with consequent poor stability and performance. In contrast, direct model reference adaptive controllers operate to force the LSS to track the desirable behavior of a chosen model. These schemes produce simple control algorithms which are easy to implement on line. One problem with their use for LSS has been that the model must be the same dimension as the LSS - i.e., quite large. A control theory based on the command generator tracker (CGT) ideas of Sobel, Mabins, Kaufman and Wen, Balas to obtain very low-order models based on adaptive algorithms was developed. Closed-loop stability for both finite element models and distributed parameter models of LSS was proved. In addition, successful numerical simulations on several LSS databases were obtained. An adaptive controller based on our theory was also implemented on a flexible robotic manipulator at Martin Marietta Astronautics. Computation schemes for controller-structure interaction with unmodeled modes, the residual mode filters or RMF, were developed. The RMF theory was modified to compensate

  1. Controls for space structures

    NASA Technical Reports Server (NTRS)

    Balas, Mark

    1991-01-01

    Assembly and operation of large space structures (LSS) in orbit will require robot-assisted docking and berthing of partially-assembled structures. These operations require new solutions to the problems of controls. This is true because of large transient and persistent disturbances, controller-structure interaction with unmodeled modes, poorly known structure parameters, slow actuator/sensor dynamical behavior, and excitation of nonlinear structure vibrations during control and assembly. For on-orbit assembly, controllers must start with finite element models of LSS and adapt on line to the best operating points, without compromising stability. This is not easy to do, since there are often unmodeled dynamic interactions between the controller and the structure. The indirect adaptive controllers are based on parameter estimation. Due to the large number of modes in LSS, this approach leads to very high-order control schemes with consequent poor stability and performance. In contrast, direct model reference adaptive controllers operate to force the LSS to track the desirable behavior of a chosen model. These schemes produce simple control algorithms which are easy to implement on line. One problem with their use for LSS has been that the model must be the same dimension as the LSS - i.e., quite large. A control theory based on the command generator tracker (CGT) ideas of Sobel, Mabins, Kaufman and Wen, Balas to obtain very low-order models based on adaptive algorithms was developed. Closed-loop stability for both finite element models and distributed parameter models of LSS was proved. In addition, successful numerical simulations on several LSS databases were obtained. An adaptive controller based on our theory was also implemented on a flexible robotic manipulator at Martin Marietta Astronautics. Computation schemes for controller-structure interaction with unmodeled modes, the residual mode filters or RMF, were developed. The RMF theory was modified to compensate

  2. Compact, Reliable EEPROM Controller

    NASA Technical Reports Server (NTRS)

    Katz, Richard; Kleyner, Igor

    2010-01-01

    A compact, reliable controller for an electrically erasable, programmable read-only memory (EEPROM) has been developed specifically for a space-flight application. The design may be adaptable to other applications in which there are requirements for reliability in general and, in particular, for prevention of inadvertent writing of data in EEPROM cells. Inadvertent writes pose risks of loss of reliability in the original space-flight application and could pose such risks in other applications. Prior EEPROM controllers are large and complex and do not provide all reasonable protections (in many cases, few or no protections) against inadvertent writes. In contrast, the present controller provides several layers of protection against inadvertent writes. The controller also incorporates a write-time monitor, enabling determination of trends in the performance of an EEPROM through all phases of testing. The controller has been designed as an integral subsystem of a system that includes not only the controller and the controlled EEPROM aboard a spacecraft but also computers in a ground control station, relatively simple onboard support circuitry, and an onboard communication subsystem that utilizes the MIL-STD-1553B protocol. (MIL-STD-1553B is a military standard that encompasses a method of communication and electrical-interface requirements for digital electronic subsystems connected to a data bus. MIL-STD- 1553B is commonly used in defense and space applications.) The intent was to both maximize reliability while minimizing the size and complexity of onboard circuitry. In operation, control of the EEPROM is effected via the ground computers, the MIL-STD-1553B communication subsystem, and the onboard support circuitry, all of which, in combination, provide the multiple layers of protection against inadvertent writes. There is no controller software, unlike in many prior EEPROM controllers; software can be a major contributor to unreliability, particularly in fault

  3. NUCLEAR REACTOR CONTROL SYSTEM

    DOEpatents

    Epler, E.P.; Hanauer, S.H.; Oakes, L.C.

    1959-11-01

    A control system is described for a nuclear reactor using enriched uranium fuel of the type of the swimming pool and other heterogeneous nuclear reactors. Circuits are included for automatically removing and inserting the control rods during the course of normal operation. Appropriate safety circuits close down the nuclear reactor in the event of emergency.

  4. Computationally efficient control allocation

    NASA Technical Reports Server (NTRS)

    Durham, Wayne (Inventor)

    2001-01-01

    A computationally efficient method for calculating near-optimal solutions to the three-objective, linear control allocation problem is disclosed. The control allocation problem is that of distributing the effort of redundant control effectors to achieve some desired set of objectives. The problem is deemed linear if control effectiveness is affine with respect to the individual control effectors. The optimal solution is that which exploits the collective maximum capability of the effectors within their individual physical limits. Computational efficiency is measured by the number of floating-point operations required for solution. The method presented returned optimal solutions in more than 90% of the cases examined; non-optimal solutions returned by the method were typically much less than 1% different from optimal and the errors tended to become smaller than 0.01% as the number of controls was increased. The magnitude of the errors returned by the present method was much smaller than those that resulted from either pseudo inverse or cascaded generalized inverse solutions. The computational complexity of the method presented varied linearly with increasing numbers of controls; the number of required floating point operations increased from 5.5 i, to seven times faster than did the minimum-norm solution (the pseudoinverse), and at about the same rate as did the cascaded generalized inverse solution. The computational requirements of the method presented were much better than that of previously described facet-searching methods which increase in proportion to the square of the number of controls.

  5. Asthma - control drugs

    MedlinePlus

    ... About MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Asthma - control drugs URL of this page: //medlineplus.gov/ency/patientinstructions/000005.htm Asthma - control ...

  6. Demand-controlled lighting

    NASA Technical Reports Server (NTRS)

    Owens, L. J.

    1977-01-01

    Automatic lighting is controlled by photocell that measures intensity of available light. Photocell drives motor which operates mercury switches controlling indoor illumination sources. Device effects increase in indoor illumination intensity when illumination input to cell is insufficient. Reverse is true if input is too great.

  7. Fiber optics for controls

    NASA Technical Reports Server (NTRS)

    Seng, Gary T.

    1987-01-01

    The challenge of those involved in control-system hardware development is to accommodate an ever-increasing complexity in aircraft control, while limiting the size and weight of the components and improving system reliability. A technology that displays promise towards this end is the area of fiber optics for controls. The primary advantages of employing optical fibers, passive optical sensors, and optically controlled actuators are weight and volume reduction, immunity from electromagnetic effects, superior bandwidth capabilities, and freedom from short circuits and sparking contacts. Since 1975, NASA Lewis has performed in-house, contract, and grant research in fiber optic sensors, high-temperature electro-optic switches, and fly-by-light control-system architecture. Passive optical sensor development is an essential yet challenging area of work and has therefore received much attention during this period. A major effort to develop fly-by-light control-system technology, known as the Fiber-Optic Control System Integration (FOCSI) program, was initiated in 1985 as a cooperative effort between NASA and DOD. Phase 1 of FOCSI, completed in 1986, was aimed at the design of a fiber-optic integrated propulsion/flight control system. Phase 2, yet to be initiated, will provide subcomponent and system development, and a system engine test. In addition to a summary of the benefits of fiber optics, the FOCSI program, sensor advances, and future directions in the NASA Lewis program will be discussed.

  8. Advanced Formation Flight Control.

    DTIC Science & Technology

    1994-12-01

    stabilizes the time dependent linearized plant (7.9) than it is to synthesize a control law which stabilizes the LTI plant (7.5). However, if a stabilizing ... control law is available, Lyapunov’s stabilizability result can also be applied to non LTI scenarios which arise from the application of linearization to

  9. Control of Nonlinear Systems.

    DTIC Science & Technology

    1980-02-26

    above papers shows how the "finite horizon time" feedback stabilization technique discussed in Section Ill-A can be extended to derive stabilizing ... control laws for the linear differential system with delayed controls: x = Ax(t) - 0 u(t) + B 1u(t - h). The second of the above papers shows how the

  10. Fluid delivery control system

    SciTech Connect

    Hoff, Brian D.; Johnson, Kris William; Algrain, Marcelo C.; Akasam, Sivaprasad

    2006-06-06

    A method of controlling the delivery of fluid to an engine includes receiving a fuel flow rate signal. An electric pump is arranged to deliver fluid to the engine. The speed of the electric pump is controlled based on the fuel flow rate signal.

  11. Duct Flow Control System.

    DTIC Science & Technology

    is ejected under pressure tangentially of local duct surfaces through Coanda affected slots at the trailing edge of the duct from which only the...channel passages in order to modify the flow stream through the duct so as to perform certain functions such as thrust control and steerage control effects enhancing vehicle maneuverability.

  12. Police Robbery Control Manual.

    ERIC Educational Resources Information Center

    Ward, Richard H.; And Others

    The manual was designed as a practical guide for police department personnel in developing robbery control programs. An introductory chapter defines types of robberies and suggests administrative and operational uses of the manual. Research and control strategies are reported according to five robbery types: street (visible and non-visible),…

  13. Birth Control Ring

    MedlinePlus

    ... It? The birth control ring is a soft, flexible, doughnut-shaped ring about 2 inches (5 centimeters) in diameter. It is inserted into the vagina, where it slowly releases hormones — the chemicals the body makes to control organ function — through the vaginal wall into the ...

  14. Avian influenza control strategies

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Control strategies for avian influenza in poultry vary depending on whether the goal is prevention, management, or eradication. Components used in control programs include: 1) education which includes communication, public awareness, and behavioral change, 2) changes to production and marketing sys...

  15. Command and Control.

    ERIC Educational Resources Information Center

    Thwaites, Donald

    1992-01-01

    Provides background information as an introduction to three articles on command and control simulations that involve police and fire departments. Elements of command and control situations are discussed, including leadership, management of people and resources, communication, and coordination; the effectiveness of simulations is considered; and…

  16. Liquid Level Control System.

    DTIC Science & Technology

    A system for controlling liquid flow from an inlet into a tank comprising a normally closed poppet valve controlled by dual pressure chambers each...containing a diaphragm movable by the pressure of the liquid in the inlet to cause the valve to close. Pressure against the diaphragms is relieved by

  17. Control without Wires.

    ERIC Educational Resources Information Center

    Hobart, Jordan

    2002-01-01

    Describes how modern lighting systems, such as wireless lighting, which come complete with user-friendly controls and audio/video interfaces, enhance the educational process and cut costs. Discusses evaluating a building's lighting situation, lighting controls, and such systems' flexibility for future needs. (EV)

  18. Rethinking Coercive Control.

    PubMed

    Stark, Evan

    2009-12-01

    The critical appraisals of Coercive Control focus largely on what my analysis implies for intervention, a matter to which the book devotes only limited space. In this reply, I reiterate core concepts in the book and acknowledge that much more work is needed to translate the realities of coercive control into practical legal and advocacy strategies. I review how coercive control differs from partner assaults and so why it merits a distinct response; the extent to which coercive control targets gender identity; the wisdom of complementing the focus on violence with an emphasis on male domination, sexual inequality and personal liberty; what this implies for shelters and the law; why sexual inequality differentiates coercive control from female partner abuse of men; how sexual equality can be both cause and antidote for coercive control; why I think an affirmative concept of freedom is essential to grasp the human rights violations inflicted by coercive control; and what it means to "story" coercive control by integrating women into the larger liberty narrative on which our national identity rests.

  19. Readings in program control

    NASA Technical Reports Server (NTRS)

    Hoban, Francis T. (Editor); Lawbaugh, William M. (Editor); Hoffman, Edward J. (Editor)

    1994-01-01

    Under the heading of Program Control, a number of related topics are discussed: cost estimating methods; planning and scheduling; cost overruns in the defense industry; the history of estimating; the advantages of cost plus award fee contracts; and how program control techniques led to the success of a NASA development project.

  20. QUALITY CONTROLS FOR PCR

    EPA Science Inventory

    The purpose of this presentation is to present an overview of the quality control (QC) sections of a draft EPA document entitled, "Quality Assurance/Quality Control Guidance for Laboratories Performing PCR Analyses on Environmental Samples." This document has been prepared by th...

  1. Programmable Logic Controllers.

    ERIC Educational Resources Information Center

    Insolia, Gerard; Anderson, Kathleen

    This document contains a 40-hour course in programmable logic controllers (PLC), developed for a business-industry technology resource center for firms in eastern Pennsylvania by Northampton Community College. The 10 units of the course cover the following: (1) introduction to programmable logic controllers; (2) DOS primer; (3) prerequisite…

  2. What Is Numerical Control?

    ERIC Educational Resources Information Center

    Goold, Vernell C.

    1977-01-01

    Numerical control (a technique involving coded, numerical instructions for the automatic control and performance of a machine tool) does not replace fundamental machine tool training. It should be added to the training program to give the student an additional tool to accomplish production rates and accuracy that were not possible before. (HD)

  3. Counseling for Pain Control

    ERIC Educational Resources Information Center

    Espin, Olivia M.; Ganikos, Mary L.

    1975-01-01

    New techniques are being developed that enhance the effectiveness of psychological forces in controlling bodily reactions. All of them are powerful tools for the psychological control of pain. This article reviews such techniques and addresses itself to the contributions that counselors can make to alleviate physical pain. (Author)

  4. Contamination Control Techniques

    SciTech Connect

    EBY, J.L.

    2000-05-16

    Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics.

  5. Multipath star switch controller

    NASA Technical Reports Server (NTRS)

    Anderson, T. O.

    1980-01-01

    Device concept permits parallel computers to scan several commonnetwork-connected data stations at maximum rate. Sequencers leap-frog to bypass ports already being serviced by another computer. Two-path system for 16-port star switch controller is cost effective if added bandwidth or increased reliability is desired. Triple-path system would be cost effective for 32-port controller.

  6. Encyclopedia of Birth Control.

    ERIC Educational Resources Information Center

    Rengel, Marian

    This encyclopedia brings together in more than 200 entries, arranged in A-to-Z format, a portrait of the complex modern issue that birth control has become with advances in medicine and biochemistry during the 20th century. It is aimed at both the student and the consumer of birth control. Entries cover the following topics: birth control…

  7. Control-structure interaction

    NASA Technical Reports Server (NTRS)

    Cheng, Joseph K.; Ianculescu, George D.; Kenney, Charles S.; Laub, Alan J.; Ly, Jason H. Q.; Papadopoulos, Philip M.

    1992-01-01

    The feasibility of using conventional proportional-integral-derivative (PID) control and an alternative optimal control to perform the pointing and tracking functions of the Space Station solar dynamic power module is investigated. A very large state model of 6 rigid body modes and 272 flexible modes is used in conjunction with classical linear-quadratic-Gaussian (LQG) optimal control to produce a full-order controller that satisfies the requirements. The results are compared with a classically designed PID controller that was implemented for a much smaller (6 rigid body, 40 flexible modes) model. The conventional control design approach is shown to be very much influenced by the order reduction of the plant model, i.e., the number of retained elastic modes from the full-order model, suggesting that for a complex, large space structure, such as the Space Station Freedom solar dynamic module, application of conventional control system design methods may not be adequate. The use of LQG control is recommended, and method for solving the large matrix. Riccati equation that arises from the optimal formulation is provided.

  8. Plating Tank Control Software

    SciTech Connect

    Krafcik, John

    1998-03-01

    The Plating Tank Control Software is a graphical user interface that controls and records plating process conditions for plating in high aspect ratio channels that require use of low current and long times. The software is written for a Pentium II PC with an 8 channel data acquisition card, and the necessary shunt resistors for measuring currents in the millampere range.

  9. DIESEL NOX CONTROL APPLICATION

    EPA Science Inventory

    The paper gives results of a project to design, develop, and demonstrate a diesel engine nitrogen oxide (NOx) and particulate matter (PM) control package that will meet the U.S. Navy's emission control requirements. (NOTE: In 1994, EPA issued a Notice for Proposed Rule Making (NP...

  10. Public Health Pest Control.

    ERIC Educational Resources Information Center

    Arizona Univ., Tucson. Cooperative Extension Service.

    This manual supplies information helpful to individuals wishing to become certified in public health pest control. It is designed as a technical reference for vector control workers and as preparatory material for structural applicators of restricted use pesticides to meet the General Standards of Competency required of commercial applicators. The…

  11. Hair follicle growth controls.

    PubMed

    Stenn, K S; Combates, N J; Eilertsen, K J; Gordon, J S; Pardinas, J R; Parimoo, S; Prouty, S M

    1996-10-01

    Research in hair biology has embarked in the pursuit for molecules that control hair growth. Many molecules already have been associated with the controls of hair patterning, hair maturation, and hair cycling and differentiation. Knowing how these molecules work gives us the tools for understanding and treating patients with hair disorders.

  12. Nonlinear and adaptive control

    NASA Technical Reports Server (NTRS)

    Athans, Michael

    1989-01-01

    The primary thrust of the research was to conduct fundamental research in the theories and methodologies for designing complex high-performance multivariable feedback control systems; and to conduct feasibiltiy studies in application areas of interest to NASA sponsors that point out advantages and shortcomings of available control system design methodologies.

  13. Who Controls the Video?

    ERIC Educational Resources Information Center

    Hanna, Jack C.

    Television plays a monumentally large role in U.S. society; no one is immune from its effects. The government does not control television, but it is not far from the truth to say that television controls the political life of this country. This paper analyzes the democratic objectives and effects of television in the United States. A brief history…

  14. Resisting Mind Control.

    ERIC Educational Resources Information Center

    Anderson, Susan M.; Zimbardo, Philip G.

    1980-01-01

    Provides conceptual analyses of mind control techniques along with practical advice on how to resist these techniques. The authors stress that effective mind control stems more from everyday social relations than from exotic technological gimmicks. Suggestions are given for resisting persuasion, resisting systems, and challenging the system.…

  15. NEUTRONIC REACTOR CONTROL

    DOEpatents

    Untermyer, S.; Hutter, E.

    1959-08-01

    This patent relates to "shadow" control of a nuclear reactor. The control means comprises a plurality ot elongated rods disposed adjacent and parallel to each other, The morphology and effects of gases generated within sections of neutron absorbing materials and equal length sections of neutron permeable materials together with means for longitudinally pcsitioning the rcds relative to each other.

  16. Controlled Stochastic Dynamical Systems

    DTIC Science & Technology

    2007-04-18

    the existence of value functions of two-player zero-sum stochastic differential games Indiana Univ. Math. Journal, 38 (1989), pp 293-314. [6] George ...control problems, Adv. Appl. Prob., 15, (1983) pp 225-254. [10] Karatzas, I. Ocone, D., Wang, H. and Zervos , M., Finite fuel singular control with

  17. Stepping motor controller

    DOEpatents

    Bourret, Steven C.; Swansen, James E.

    1984-01-01

    A stepping motor is microprocessingly controlled by digital circuitry which monitors the output of a shaft encoder adjustably secured to the stepping motor and generates a subsequent stepping pulse only after the preceding step has occurred and a fixed delay has expired. The fixed delay is variable on a real-time basis to provide for smooth and controlled deceleration.

  18. Stepping motor controller

    DOEpatents

    Bourret, S.C.; Swansen, J.E.

    1982-07-02

    A stepping motor is microprocessor controlled by digital circuitry which monitors the output of a shaft encoder adjustably secured to the stepping motor and generates a subsequent stepping pulse only after the preceding step has occurred and a fixed delay has expired. The fixed delay is variable on a real-time basis to provide for smooth and controlled deceleration.

  19. Automotive Pollution Control.

    ERIC Educational Resources Information Center

    Raudenbush, David B.

    Intended for a 1- or 2-month curriculum in auto mechanics, this student manual on automotive pollution control was developed by a subject matter specialist at an area vocational school and tested in a vocational auto shop. Intended either for use in an integrated curriculum or for use in teaching pollution control as a separate course, these 12…

  20. Guidance and Control Software,

    DTIC Science & Technology

    1980-05-01

    FACILITIES Integration Facilities exist for each project and consist of laboratory hot mockups of the actual military computers with realistic...PCIN Al. WEP I AND CONTROL AND CONTRI IF S TO R ESI I I I AIR-SURFACE ASGW WEAPONS I CONTROL L - - L - - - - - - - J L J FIG. 2a 3. HARDWARE

  1. Digital flight control systems

    NASA Technical Reports Server (NTRS)

    Caglayan, A. K.; Vanlandingham, H. F.

    1977-01-01

    The design of stable feedback control laws for sampled-data systems with variable rate sampling was investigated. These types of sampled-data systems arise naturally in digital flight control systems which use digital actuators where it is desirable to decrease the number of control computer output commands in order to save wear and tear of the associated equipment. The design of aircraft control systems which are optimally tolerant of sensor and actuator failures was also studied. Detection of the failed sensor or actuator must be resolved and if the estimate of the state is used in the control law, then it is also desirable to have an estimator which will give the optimal state estimate even under the failed conditions.

  2. Estimation in satellite control.

    NASA Technical Reports Server (NTRS)

    Debra, D. B.

    1971-01-01

    The use of estimators or observers is discussed as applied to satellite attitude control and the control of drag-free satellites. The practical problems of implementation are discussed, and the relative advantages of full and reduced state estimators are compared, particularly in terms of their effectiveness and bandwidth as filters. Three applications are used to illustrate the principles. They are: (1) a reaction wheel control system, (2) a spinning attitude control system, and (3) a drag-free satellite translational control system. Fixed estimator gains are shown to be adequate for these (and many other) applications. Our experience in the hardware realization of estimators has led to categorize the error sources in terms of those that improve with increased estimator gains and those that get worse with increased estimator gains.

  3. Autorotation flight control system

    NASA Technical Reports Server (NTRS)

    Bachelder, Edward N. (Inventor); Lee, Dong-Chan (Inventor); Aponso, Bimal L. (Inventor)

    2011-01-01

    The present invention provides computer implemented methodology that permits the safe landing and recovery of rotorcraft following engine failure. With this invention successful autorotations may be performed from well within the unsafe operating area of the height-velocity profile of a helicopter by employing the fast and robust real-time trajectory optimization algorithm that commands control motion through an intuitive pilot display, or directly in the case of autonomous rotorcraft. The algorithm generates optimal trajectories and control commands via the direct-collocation optimization method, solved using a nonlinear programming problem solver. The control inputs computed are collective pitch and aircraft pitch, which are easily tracked and manipulated by the pilot or converted to control actuator commands for automated operation during autorotation in the case of an autonomous rotorcraft. The formulation of the optimal control problem has been carefully tailored so the solutions resemble those of an expert pilot, accounting for the performance limitations of the rotorcraft and safety concerns.

  4. Remotely controllable mixing system

    NASA Technical Reports Server (NTRS)

    Belew, Robert R. (Inventor)

    1987-01-01

    A remotely controllable mixing system (210) in which a plurality of mixing assemblies (10a-10e) are arranged in an annular configuration, and wherein each assembly (10) employs a central chamber (16) and two outer, upper and lower, chambers (12, 14). Valves (18, 20) are positioned between chambers, and these valves (18, 20) for a given mixing assembly (10) are operated by upper and lower control rotors (29), which in turn are driven by upper and lower drive rotors (270, 270b). Additionally, a hoop (278) is compressed around upper control rotors (29) and a hoop (278b) is compressed around lower control rotors (29) to thus insure constant frictional engagement between all control rotors (29) and drive rotors (270, 270b). The drive rollers (270, 270b) are driven by a motor (213).

  5. Intelligent Flow Control Valve

    NASA Technical Reports Server (NTRS)

    Kelley, Anthony R (Inventor)

    2015-01-01

    The present invention is an intelligent flow control valve which may be inserted into the flow coming out of a pipe and activated to provide a method to stop, measure, and meter flow coming from the open or possibly broken pipe. The intelligent flow control valve may be used to stop the flow while repairs are made. Once repairs have been made, the valve may be removed or used as a control valve to meter the amount of flow from inside the pipe. With the addition of instrumentation, the valve may also be used as a variable area flow meter and flow controller programmed based upon flowing conditions. With robotic additions, the valve may be configured to crawl into a desired pipe location, anchor itself, and activate flow control or metering remotely.

  6. CAVITY CONTROL ALGORITHM

    SciTech Connect

    Tomasz Plawski, J. Hovater

    2010-09-01

    A digital low level radio frequency (RF) system typically incorporates either a heterodyne or direct sampling technique, followed by fast ADCs, then an FPGA, and finally a transmitting DAC. This universal platform opens up the possibilities for a variety of control algorithm implementations. The foremost concern for an RF control system is cavity field stability, and to meet the required quality of regulation, the chosen control system needs to have sufficient feedback gain. In this paper we will investigate the effectiveness of the regulation for three basic control system algorithms: I&Q (In-phase and Quadrature), Amplitude & Phase and digital SEL (Self Exciting Loop) along with the example of the Jefferson Lab 12 GeV cavity field control system.

  7. Discrete Variational Optimal Control

    NASA Astrophysics Data System (ADS)

    Jiménez, Fernando; Kobilarov, Marin; Martín de Diego, David

    2013-06-01

    This paper develops numerical methods for optimal control of mechanical systems in the Lagrangian setting. It extends the theory of discrete mechanics to enable the solutions of optimal control problems through the discretization of variational principles. The key point is to solve the optimal control problem as a variational integrator of a specially constructed higher dimensional system. The developed framework applies to systems on tangent bundles, Lie groups, and underactuated and nonholonomic systems with symmetries, and can approximate either smooth or discontinuous control inputs. The resulting methods inherit the preservation properties of variational integrators and result in numerically robust and easily implementable algorithms. Several theoretical examples and a practical one, the control of an underwater vehicle, illustrate the application of the proposed approach.

  8. Shock absorber control system

    SciTech Connect

    Nakano, Y.; Ohira, M.; Ushida, M.; Miyagawa, T.; Shimodaira, T.

    1987-01-13

    A shock absorber control system is described for controlling a dampening force of a shock absorber of a vehicle comprising: setting means for setting a desired dampening force changeable within a predetermined range; drive means for driving the shock absorber to change the dampening force of the shock absorber linearly; control means for controlling the drive means in accordance with the desired dampening force when the setting of the desired dampening force has been changed; detecting means for detecting an actual dampening force of the shock absorber; and correcting means for correcting the dampening force of the shock absorber by controlling the drive means in accordance with a difference between the desired dampening force and the detected actual dampening force.

  9. Cyclic control stick

    DOEpatents

    Whitaker, Charles N.; Zimmermann, Richard E.

    1989-01-01

    A cyclic control stick of the type used in helicopters for reducing the safety hazards associated with such a mechanism in the event of a crewman being thrown violently into contact with the cyclic control stick resulting from a crash or the like. The cyclic control stick is configured to break away upon the exertion of an impact force which exceeds a predetermined value and/or is exerted for more than a momentary time duration. The cyclic control stick is also configured to be adjustable so as to locate the grip thereof as far away from the crewman as possible for safety reasons without comprising the comfort of the crewman or the use of the control stick, and a crushable pad is provided on the top of the grip for impact energy absorbing purposes.

  10. 3. EAGLE ROCK CONTROL CENTER, OPERATIONS CONTROL. AS SYSTEM BECOMES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. EAGLE ROCK CONTROL CENTER, OPERATIONS CONTROL. AS SYSTEM BECOMES INCREASINGLY AUTOMATED, EAGLE ROCK WILL BECOME MORE AND MORE THE CENTRAL CONTROL SYSTEM OF THE METROPOLITAN WATER DISTRICT. - Eagle Rock Operations Control Center, Pasadena, Los Angeles County, CA

  11. Neural Flight Control System

    NASA Technical Reports Server (NTRS)

    Gundy-Burlet, Karen

    2003-01-01

    The Neural Flight Control System (NFCS) was developed to address the need for control systems that can be produced and tested at lower cost, easily adapted to prototype vehicles and for flight systems that can accommodate damaged control surfaces or changes to aircraft stability and control characteristics resulting from failures or accidents. NFCS utilizes on a neural network-based flight control algorithm which automatically compensates for a broad spectrum of unanticipated damage or failures of an aircraft in flight. Pilot stick and rudder pedal inputs are fed into a reference model which produces pitch, roll and yaw rate commands. The reference model frequencies and gains can be set to provide handling quality characteristics suitable for the aircraft of interest. The rate commands are used in conjunction with estimates of the aircraft s stability and control (S&C) derivatives by a simplified Dynamic Inverse controller to produce virtual elevator, aileron and rudder commands. These virtual surface deflection commands are optimally distributed across the aircraft s available control surfaces using linear programming theory. Sensor data is compared with the reference model rate commands to produce an error signal. A Proportional/Integral (PI) error controller "winds up" on the error signal and adds an augmented command to the reference model output with the effect of zeroing the error signal. In order to provide more consistent handling qualities for the pilot, neural networks learn the behavior of the error controller and add in the augmented command before the integrator winds up. In the case of damage sufficient to affect the handling qualities of the aircraft, an Adaptive Critic is utilized to reduce the reference model frequencies and gains to stay within a flyable envelope of the aircraft.

  12. Extended cooperative control synthesis

    NASA Technical Reports Server (NTRS)

    Davidson, John B.; Schmidt, David K.

    1994-01-01

    This paper reports on research for extending the Cooperative Control Synthesis methodology to include a more accurate modeling of the pilot's controller dynamics. Cooperative Control Synthesis (CCS) is a methodology that addresses the problem of how to design control laws for piloted, high-order, multivariate systems and/or non-conventional dynamic configurations in the absence of flying qualities specifications. This is accomplished by emphasizing the parallel structure inherent in any pilot-controlled, augmented vehicle. The original CCS methodology is extended to include the Modified Optimal Control Model (MOCM), which is based upon the optimal control model of the human operator developed by Kleinman, Baron, and Levison in 1970. This model provides a modeling of the pilot's compensation dynamics that is more accurate than the simplified pilot dynamic representation currently in the CCS methodology. Inclusion of the MOCM into the CCS also enables the modeling of pilot-observation perception thresholds and pilot-observation attention allocation affects. This Extended Cooperative Control Synthesis (ECCS) allows for the direct calculation of pilot and system open- and closed-loop transfer functions in pole/zero form and is readily implemented in current software capable of analysis and design for dynamic systems. Example results based upon synthesizing an augmentation control law for an acceleration command system in a compensatory tracking task using the ECCS are compared with a similar synthesis performed by using the original CCS methodology. The ECCS is shown to provide augmentation control laws that yield more favorable, predicted closed-loop flying qualities and tracking performance than those synthesized using the original CCS methodology.

  13. On identified predictive control

    NASA Technical Reports Server (NTRS)

    Bialasiewicz, Jan T.

    1993-01-01

    Self-tuning control algorithms are potential successors to manually tuned PID controllers traditionally used in process control applications. A very attractive design method for self-tuning controllers, which has been developed over recent years, is the long-range predictive control (LRPC). The success of LRPC is due to its effectiveness with plants of unknown order and dead-time which may be simultaneously nonminimum phase and unstable or have multiple lightly damped poles (as in the case of flexible structures or flexible robot arms). LRPC is a receding horizon strategy and can be, in general terms, summarized as follows. Using assumed long-range (or multi-step) cost function the optimal control law is found in terms of unknown parameters of the predictor model of the process, current input-output sequence, and future reference signal sequence. The common approach is to assume that the input-output process model is known or separately identified and then to find the parameters of the predictor model. Once these are known, the optimal control law determines control signal at the current time t which is applied at the process input and the whole procedure is repeated at the next time instant. Most of the recent research in this field is apparently centered around the LRPC formulation developed by Clarke et al., known as generalized predictive control (GPC). GPC uses ARIMAX/CARIMA model of the process in its input-output formulation. In this paper, the GPC formulation is used but the process predictor model is derived from the state space formulation of the ARIMAX model and is directly identified over the receding horizon, i.e., using current input-output sequence. The underlying technique in the design of identified predictive control (IPC) algorithm is the identification algorithm of observer/Kalman filter Markov parameters developed by Juang et al. at NASA Langley Research Center and successfully applied to identification of flexible structures.

  14. Velocity vector control system augmented with direct lift control

    NASA Technical Reports Server (NTRS)

    Tisdale, H. F., Sr.; Kelly, W. W. (Inventor)

    1981-01-01

    A pilot-controlled stability control system that employs direct lift control (spoiler control) with elevator control to control the flight path angle of an aircraft is described. A computer on the aircraft generates an elevator control signal and a spoiler control signal, using a pilot-controlled pitch control signal and pitch rate, vertical velocity, roll angle, groundspeed, engine pressure ratio and vertical acceleration signals which are generated on the aircraft. The direct lift control by the aircraft spoilers improves the response of the aircraft flight path angle and provides short term flight path stabilization against environmental disturbances.

  15. Load Control System Reliability

    SciTech Connect

    Trudnowski, Daniel

    2015-04-03

    This report summarizes the results of the Load Control System Reliability project (DOE Award DE-FC26-06NT42750). The original grant was awarded to Montana Tech April 2006. Follow-on DOE awards and expansions to the project scope occurred August 2007, January 2009, April 2011, and April 2013. In addition to the DOE monies, the project also consisted of matching funds from the states of Montana and Wyoming. Project participants included Montana Tech; the University of Wyoming; Montana State University; NorthWestern Energy, Inc., and MSE. Research focused on two areas: real-time power-system load control methodologies; and, power-system measurement-based stability-assessment operation and control tools. The majority of effort was focused on area 2. Results from the research includes: development of fundamental power-system dynamic concepts, control schemes, and signal-processing algorithms; many papers (including two prize papers) in leading journals and conferences and leadership of IEEE activities; one patent; participation in major actual-system testing in the western North American power system; prototype power-system operation and control software installed and tested at three major North American control centers; and, the incubation of a new commercial-grade operation and control software tool. Work under this grant certainly supported the DOE-OE goals in the area of “Real Time Grid Reliability Management.”

  16. Gemini Scout Control Software

    SciTech Connect

    Clinton Hobart, Justin Garretson

    2010-11-23

    The Gemini Scout Control Software consists of two Windows applications that allow the Gemini Scout vehicle to be controlled by an operator. The Embedded application runs on the vehicle's Gemini Scout Control Software onboard computer and controls the vehicle's various motors and sensors. This application reports the vehicle's status and receives vehicle commands overthe local-area-network. The Embedded applicationalso allows the user to control the vehicle using a USB game-pad connected directly to the vehicle. The Operator Control Unit (OCU) application runs on an external PC and communicates with the vehicle via an Ethernet connection. The OCU application sends commands to and receives data from the Embedded application running on the vehicle. The OCU application also communicates directly with the digital video encoders and radios in order to display video from the vehicle's cameras and the status of the radio link. The OCU application has a graphical user interface (GUI) that displays the vehicle's status and allows the user to change various vehicle settings. Finally, the OCU application receives input from a USB game-pad connected to the PC in order to control the vehicle's functions.

  17. Control of vortex dynamics

    NASA Astrophysics Data System (ADS)

    Chang, Hsiao-Lung

    Discrete vortex methods are used to provide computationally efficient simulations of vortex dynamics in fluid flows. An adaptive LQG controller is applied to reduce the oscillations in the wake caused by the vortex dynamics. The controller design is based on a discrete-time input/output model rather than the nonlinear differential equations of the discrete vortex model. The control philosophy is to identify time-varying parameters in the input/output model adaptively and use the identified parameters to update the control law. For numerically stable identification, an adaptive algorithm based on inverse QR decomposition is introduced. The derivation shows that this algorithm is a square-root implementation of recursive least squares estimation. For a preliminary test of the control strategy, the adaptive LQG controller is applied to a vortex street model simulated by discrete vortices. The identification shows that the stability of the identified zeros depends on whether the sensor is upstream or downstream of the actuator. Flow past a flat plate is another important application of the discrete vortex method. A control problem is studied and simulated in which suction at the back face of the plate is used to trap vortices behind the plate. Qualitatively, the results obtained with the discrete-vortex method used here agree with earlier results for a substantially different vortex method involving a small number of differential equations.

  18. Fiber optics for controls

    NASA Technical Reports Server (NTRS)

    Seng, Gary T.

    1990-01-01

    The design, development, and testing of a fiber optic integrated propulsion/flight control system for an advanced supersonic dash aircraft (flies at supersonic speeds for short periods of time) is the goal of the joint NASA/DOD Fiber Optic Control System Integration (FOCSI) program. Phase 1 provided a comparison of electronic and optical control systems, identified the status of current optical sensor technology, defined the aircraft sensor/actuator environment, proposed architectures for fully optical control systems, and provided schedules for development. Overall, it was determined that there are sufficient continued efforts to develop such a system. It was also determined that it is feasible to build a fiber optic control system for the development of a data base for this technology, but that further work is necessary in sensors, actuators, and components to develop an optimum design, fully fiber optic integrated control system compatible with advanced aircraft environments. Phase 2 is to design, construct, and ground test a fly by light control system. Its first task is to provide a detailed design of the electro-optic architecture.

  19. Controllability of flow turbulence.

    PubMed

    Guan, Shuguang; Wei, G W; Lai, C-H

    2004-06-01

    In this paper, we study the controllability of real-world flow turbulence governed by the two-dimensional Navier-Stokes equations, using strategies developed in chaos control. A case of control/synchronization of turbulent dynamics is observed when only one component of the velocity field vector is unidirectionally coupled to a target state, while the other component is uncoupled. Unlike previous results, it is shown that the dynamics of the whole velocity field cannot be completely controlled/synchronized to the target, even in the limit of long time and strong coupling strength. It is further revealed that the controlled component of the velocity field can be fully controlled/synchronized to the target, but the other component, which is not directly coupled to the target, can only be partially controlled/synchronized to the target. By extending an auxiliary method to distributed dynamic systems, the partial synchronization of two turbulent orbits in the present study can be categorized in the domain of generalized synchronization of spatiotemporal dynamics.

  20. IGISOL control system modernization

    NASA Astrophysics Data System (ADS)

    Koponen, J.; Hakala, J.

    2016-06-01

    Since 2010, the IGISOL research facility at the Accelerator laboratory of the University of Jyväskylä has gone through major changes. Comparing the new IGISOL4 facility to the former IGISOL3 setup, the size of the facility has more than doubled, the length of the ion transport line has grown to about 50 m with several measurement setups and extension capabilities, and the accelerated ions can be fed to the facility from two different cyclotrons. The facility has evolved to a system comprising hundreds of manual, pneumatic and electronic devices. These changes have prompted the need to modernize also the facility control system taking care of monitoring and transporting the ion beams. In addition, the control system is also used for some scientific data acquisition tasks. Basic guidelines for the IGISOL control system update have been remote control, safety, usability, reliability and maintainability. Legacy components have had a major significance in the control system hardware and for the renewed control system software the Experimental Physics and Industrial Control System (EPICS) has been chosen as the architectural backbone.

  1. Deadbeat Predictive Controllers

    NASA Technical Reports Server (NTRS)

    Juang, Jer-Nan; Phan, Minh

    1997-01-01

    Several new computational algorithms are presented to compute the deadbeat predictive control law. The first algorithm makes use of a multi-step-ahead output prediction to compute the control law without explicitly calculating the controllability matrix. The system identification must be performed first and then the predictive control law is designed. The second algorithm uses the input and output data directly to compute the feedback law. It combines the system identification and the predictive control law into one formulation. The third algorithm uses an observable-canonical form realization to design the predictive controller. The relationship between all three algorithms is established through the use of the state-space representation. All algorithms are applicable to multi-input, multi-output systems with disturbance inputs. In addition to the feedback terms, feed forward terms may also be added for disturbance inputs if they are measurable. Although the feedforward terms do not influence the stability of the closed-loop feedback law, they enhance the performance of the controlled system.

  2. Fault tolerant control laws

    NASA Technical Reports Server (NTRS)

    Ly, U. L.; Ho, J. K.

    1986-01-01

    A systematic procedure for the synthesis of fault tolerant control laws to actuator failure has been presented. Two design methods were used to synthesize fault tolerant controllers: the conventional LQ design method and a direct feedback controller design method SANDY. The latter method is used primarily to streamline the full-state Q feedback design into a practical implementable output feedback controller structure. To achieve robustness to control actuator failure, the redundant surfaces are properly balanced according to their control effectiveness. A simple gain schedule based on the landing gear up/down logic involving only three gains was developed to handle three design flight conditions: Mach .25 and Mach .60 at 5000 ft and Mach .90 at 20,000 ft. The fault tolerant control law developed in this study provides good stability augmentation and performance for the relaxed static stability aircraft. The augmented aircraft responses are found to be invariant to the presence of a failure. Furthermore, single-loop stability margins of +6 dB in gain and +30 deg in phase were achieved along with -40 dB/decade rolloff at high frequency.

  3. Model based manipulator control

    NASA Technical Reports Server (NTRS)

    Petrosky, Lyman J.; Oppenheim, Irving J.

    1989-01-01

    The feasibility of using model based control (MBC) for robotic manipulators was investigated. A double inverted pendulum system was constructed as the experimental system for a general study of dynamically stable manipulation. The original interest in dynamically stable systems was driven by the objective of high vertical reach (balancing), and the planning of inertially favorable trajectories for force and payload demands. The model-based control approach is described and the results of experimental tests are summarized. Results directly demonstrate that MBC can provide stable control at all speeds of operation and support operations requiring dynamic stability such as balancing. The application of MBC to systems with flexible links is also discussed.

  4. Moving Object Control System

    NASA Technical Reports Server (NTRS)

    Arndt, G. Dickey (Inventor); Carl, James R. (Inventor)

    2001-01-01

    A method is provided for controlling two objects relatively moveable with respect to each other. A plurality of receivers are provided for detecting a distinctive microwave signal from each of the objects and measuring the phase thereof with respect to a reference signal. The measured phase signal is used to determine a distance between each of the objects and each of the plurality of receivers. Control signals produced in response to the relative distances are used to control the position of the two objects.

  5. Shaft speed control

    NASA Technical Reports Server (NTRS)

    Ford, A. G.

    1979-01-01

    Simple mechanism controls rotation of heavy-duty shaft by mechanical comparison with rotation of small, precise, stepper motor. Mechanism can be used to limit winding and unwinding speeds of large spools and reels and to control speed of other rotating shafts. Setup incorporates reference shaft geared down from stepper motor and feedback shaft geared up from shaft to be controlled. Feedback and reference shafts are coupled with brake assembly inside stationary cylinder. When work shaft speeds up, brakes are activated automatically to slow it down.

  6. Flash protection controller

    DOEpatents

    Galbraith, Lee K.

    1981-01-01

    A controller provides a high voltage to maintain an electro-optic shutter in a transparent condition until a flash of light which would be harmful to personnel is sensed by a phototransistor. The controller then shorts the shutter to ground to minimize light transmission to the user and maintains light transmission at the pre-flash level for a predetermined time to allow the flash to subside. A log converter and differential trigger circuit keep the controller from being triggered by other light flashes which are not dangerous.

  7. Temperature-Controlling Circuit

    NASA Technical Reports Server (NTRS)

    Temple, Gerald

    1987-01-01

    Simple circuit switches current to electrical heater on and off to maintain temperature of room at 25 plus or minus 0.5 degree C. Lightweight, compact, reliable, insensitive to electrical noise, and uses single 5-Vdc power supply. Handles ac loads of 10 A. Designed to operate outside temperature controlled environment over range of -55 to +85 degree C. Thermistor provides input signal for simple temperature controller. Output of controller applied to solid-state relay, which in turn switches current to resistance heater.

  8. Analyzing Feedback Control Systems

    NASA Technical Reports Server (NTRS)

    Bauer, Frank H.; Downing, John P.

    1987-01-01

    Interactive controls analysis (INCA) program developed to provide user-friendly environment for design and analysis of linear control systems, primarily feedback control. Designed for use with both small- and large-order systems. Using interactive-graphics capability, INCA user quickly plots root locus, frequency response, or time response of either continuous-time system or sampled-data system. Configuration and parameters easily changed, allowing user to design compensation networks and perform sensitivity analyses in very convenient manner. Written in Pascal and FORTRAN.

  9. Surface controlled blade stabilizer

    DOEpatents

    Russell, Larry R.

    1983-01-01

    Drill string stabilizer apparatus, controllable to expand and retract entirely from the surface by control of drill string pressure, wherein increase of drill string pressure from the surface closes a valve to create a piston means which is moved down by drill string pressure to expand the stabilizer blades, said valve being opened and the piston moving upward upon reduction of drill string pressure to retract the stabilizer blades. Upward and downward movements of the piston and an actuator sleeve therebelow are controlled by a barrel cam acting between the housing and the actuator sleeve.

  10. Optical controlled keyboard system

    NASA Astrophysics Data System (ADS)

    Budzyński, Łukasz; Długosz, Dariusz; Niewiarowski, Bartosz; Zajkowski, Maciej

    2011-06-01

    Control systems of our computers are common devices, based on the manipulation of keys or a moving ball. Completely healthy people have no problems with the operation of such devices. Human disability makes everyday activities become a challenge and create trouble. When a man can not move his hands, the work becomes difficult or often impossible. Controlled optical keyboard is a modern device that allows to bypass the limitations of disability limbs. The use of wireless optical transmission allows to control computer using a laser beam, which cooperates with the photodetectors. The article presents the construction and operation of non-contact optical keyboard for people with disabilities.

  11. Advanced Wavefront Control Techniques

    SciTech Connect

    Olivier, S S; Brase, J M; Avicola, K; Thompson, C A; Kartz, M W; Winters, S; Hartley, R; Wihelmsen, J; Dowla, F V; Carrano, C J; Bauman, B J; Pennington, D M; Lande, D; Sawvel, R M; Silva, D A; Cooke, J B; Brown, C G

    2001-02-21

    Programs at LLNL that involve large laser systems--ranging from the National Ignition Facility to new tactical laser weapons--depend on the maintenance of laser beam quality through precise control of the optical wavefront. This can be accomplished using adaptive optics, which compensate for time-varying aberrations that are often caused by heating in a high-power laser system. Over the past two decades, LLNL has developed a broad capability in adaptive optics technology for both laser beam control and high-resolution imaging. This adaptive optics capability has been based on thin deformable glass mirrors with individual ceramic actuators bonded to the back. In the case of high-power lasers, these adaptive optics systems have successfully improved beam quality. However, as we continue to extend our applications requirements, the existing technology base for wavefront control cannot satisfy them. To address this issue, this project studied improved modeling tools to increase our detailed understanding of the performance of these systems, and evaluated novel approaches to low-order wavefront control that offer the possibility of reduced cost and complexity. We also investigated improved beam control technology for high-resolution wavefront control. Many high-power laser systems suffer from high-spatial-frequency aberrations that require control of hundreds or thousands of phase points to provide adequate correction. However, the cost and size of current deformable mirrors can become prohibitive for applications requiring more than a few tens of phase control points. New phase control technologies are becoming available which offer control of many phase points with small low-cost devices. The goal of this project was to expand our wavefront control capabilities with improved modeling tools, new devices that reduce system cost and complexity, and extensions to high spatial and temporal frequencies using new adaptive optics technologies. In FY 99, the second year of

  12. Flash protection controller

    DOEpatents

    Galbraith, L.K.

    1979-12-07

    A controller provides a high voltage to maintain an electro-optic shutter in a transparent condition until a flash of light which would be harmful to personnel is sensed by a phototransistor. The controller then shorts the shutter to ground to minimize light transmission to the user and maintains light transmission at the pre-flash level for a predetermined time to allow the flash to subside. A log converter and differential trigger circuit keep the controller from being triggered by other light flashes which are not dangerous.

  13. Splines and control theory

    NASA Technical Reports Server (NTRS)

    Zhang, Zhimin; Tomlinson, John; Martin, Clyde

    1994-01-01

    In this work, the relationship between splines and the control theory has been analyzed. We show that spline functions can be constructed naturally from the control theory. By establishing a framework based on control theory, we provide a simple and systematic way to construct splines. We have constructed the traditional spline functions including the polynomial splines and the classical exponential spline. We have also discovered some new spline functions such as trigonometric splines and the combination of polynomial, exponential and trigonometric splines. The method proposed in this paper is easy to implement. Some numerical experiments are performed to investigate properties of different spline approximations.

  14. Radiological Control Manual

    SciTech Connect

    Not Available

    1993-04-01

    This manual has been prepared by Lawrence Berkeley Laboratory to provide guidance for site-specific additions, supplements, and clarifications to the DOE Radiological Control Manual. The guidance provided in this manual is based on the requirements given in Title 10 Code of Federal Regulations Part 835, Radiation Protection for Occupational Workers, DOE Order 5480.11, Radiation Protection for Occupational Workers, and the DOE Radiological Control Manual. The topics covered are (1) excellence in radiological control, (2) radiological standards, (3) conduct of radiological work, (4) radioactive materials, (5) radiological health support operations, (6) training and qualification, and (7) radiological records.

  15. Infection prevention and control.

    PubMed

    Pegram, Anne; Bloomfield, Jacqueline

    2015-03-18

    All newly registered graduate nurses are required to have the appropriate knowledge and understanding to perform the skills required for patient care, specifically the competencies identified in the Nursing and Midwifery Council's essential skills clusters. This article focuses on the third essential skills cluster - infection prevention and control. It provides an overview and discussion of the key skills and behaviours that must be demonstrated to meet the standards set by the Nursing and Midwifery Council. In doing so, it considers the key principles of infection prevention and control, including local and national policies, standard infection control precautions, risk assessment, standard isolation measures and asepsis.

  16. Optimized joystick controller.

    PubMed

    Ding, D; Cooper, R A; Spaeth, D

    2004-01-01

    The purpose of the study was to develop an optimized joystick control interface for electric powered wheelchairs and thus provide safe and effective control of electric powered wheelchairs to people with severe physical disabilities. The interface enables clinicians to tune joystick parameters for each individual subject through selecting templates, dead zones, and bias axes. In terms of hand tremor usually associated with people with traumatic brain injury, cerebral palsy, and multiple sclerosis, fuzzy logic rules were applied to suppress erratic hand movements and extract the intended motion from the joystick. Simulation results were presented to show the graphical tuning interface as well as the performance of the fuzzy logic controller.

  17. Cockpit control system

    NASA Technical Reports Server (NTRS)

    Lesnewski, David; Snow, Russ M.; Paufler, Dave; Schnieder, George; Athousake, Roxanne; Combs, Lisa

    1993-01-01

    The purpose of this project is to provide a detail design for the cockpit control system of the Viper PFT. The statement of work for this project requires provisions for control of the ailerons, elevator, rudder, and elevator trim. The system should provide adjustment for pilot stature, rigging, and maintenance. MIL-STD-1472 is used as a model for human factors criterion. The system is designed to the pilot limit loading outlined in FAR part 23.397. The general philosophy behind this design is to provide a simple, reliable control system which will withstand the daily abuse that is experienced in the training environment without excessive cost or weight penalties.

  18. Asthma Triggers: Gain Control

    MedlinePlus

    ... of Page Additional resources An Introduction to Indoor Air Quality: Biological Pollutants Help Your Child Gain Control Over ... exhaust, smoke, road dust and factory emissions. Outdoor air quality is also affected by pollen from plants, crops ...

  19. Digital numerically controlled oscillator

    NASA Technical Reports Server (NTRS)

    Cellier, A.; Huey, D. C.; Ma, L. N. (Inventor)

    1980-01-01

    The frequency and phase of an output signal from an oscillator circuit are controlled with accuracy by a digital input word. Positive and negative alterations in output frequency are both provided for by translating all values of input words so that they are positive. The oscillator reference frequency is corrected only in one direction, by adding phase to the output frequency of the oscillator. The input control word is translated to a single algebraic sign and the digital 1 is added thereto. The translated input control word is then accumulated. A reference clock signal having a frequency at an integer multiple of the desired frequency of the output signal is generated. The accumulated control word is then compared with a threshold level. The output signal is adjusted in a single direction by dividing the frequency of the reference clock signal by a first integer or by an integer different from the first integer.

  20. Engineering of metabolic control

    DOEpatents

    Liao, James C.

    2004-03-16

    The invention features a method of producing heterologous molecules in cells under the regulatory control of a metabolite and metabolic flux. The method can enhance the synthesis of heterologous polypeptides and metabolites.

  1. Engineering of metabolic control

    DOEpatents

    Liao, James C.

    2006-10-17

    The invention features a method of producing heterologous molecules in cells under the regulatory control of a metabolite and metabolic flux. The method can enhance the synthesis of heterologous polypeptides and metabolites.

  2. Odor Control Technology

    ERIC Educational Resources Information Center

    Turk, Amos; And Others

    1972-01-01

    Dispersion, chemical oxidation, and masking are reviewed as techniques primarily employed for odor control. Devices and systems, costs, and problems of measurement are considered in light of environmental agencies' efforts to curb smelly emissions. (BL)

  3. Controlling Cholesterol with Statins

    MedlinePlus

    ... For Consumers Home For Consumers Consumer Updates Controlling Cholesterol with Statins Share Tweet Linkedin Pin it More ... not, the following tips can help keep your cholesterol in check: Talk with your healthcare provider about ...

  4. Riot Control Agents

    MedlinePlus

    ... CDC.gov . Specific Hazards Bioterrorism A-Z Anthrax (Bacillus anthracis) Arenaviruses Treatment & Infection Control Specimen Submission & Lab Testing Education & Training Related Bioterrorism Resources Bacillus anthracis (Anthrax) Botulism (Clostridium botulinum toxin) Brucella species ( ...

  5. Monitoring by Control Technique

    EPA Pesticide Factsheets

    Stationary source emissions monitoring is required to demonstrate that a source is meeting the requirements in Federal or state rules. This page links to different control techniques used to reduce pollutant emissions.

  6. CHLORINATED SOLVENT PLUME CONTROL

    EPA Science Inventory

    This lecture will cover recent success in controlling and assessing the treatment of shallow ground water plumes of chlorinated solvents, other halogenated organic compounds, and methyl tert-butyl ether (MTBE).

  7. Uncertainty and Cognitive Control

    PubMed Central

    Mushtaq, Faisal; Bland, Amy R.; Schaefer, Alexandre

    2011-01-01

    A growing trend of neuroimaging, behavioral, and computational research has investigated the topic of outcome uncertainty in decision-making. Although evidence to date indicates that humans are very effective in learning to adapt to uncertain situations, the nature of the specific cognitive processes involved in the adaptation to uncertainty are still a matter of debate. In this article, we reviewed evidence suggesting that cognitive control processes are at the heart of uncertainty in decision-making contexts. Available evidence suggests that: (1) There is a strong conceptual overlap between the constructs of uncertainty and cognitive control; (2) There is a remarkable overlap between the neural networks associated with uncertainty and the brain networks subserving cognitive control; (3) The perception and estimation of uncertainty might play a key role in monitoring processes and the evaluation of the “need for control”; (4) Potential interactions between uncertainty and cognitive control might play a significant role in several affective disorders. PMID:22007181

  8. Odor control in lagoons.

    PubMed

    Zhang, X L; Yan, S; Tyagi, R D; Surampalli, R Y

    2013-07-30

    Lagoons are widely used in rural area for wastewater treatment; however, the odor problem has hampered its application. The root of odor emission from lagoons varies from one to another. The key of controlling the odor is to find out the cause and accordingly provide strategies. Various physical, chemical, and biological methods have been reported and applied for odor control. Physical technologies such as masking, capturing and sorption are often employed to mitigate the pressure from compliant while not to cut off the problem. Chemical technologies which act rapidly and efficiently in odor control, utilize chemicals to damage the odorant production root or convert odorant to odorless substances. Biological methods such as aeration, biocover and biofiltration control the odor by enhancing aerobic condition or developing methanogens in lagoon, and biologically decomposing the odorants. Comparing to physical and chemical methods, biological methods are more feasible.

  9. ELECTRONIC PHASE CONTROL CIRCUIT

    DOEpatents

    Salisbury, J.D.; Klein, W.W.; Hansen, C.F.

    1959-04-21

    An electronic circuit is described for controlling the phase of radio frequency energy applied to a multicavity linear accelerator. In one application of the circuit two cavities are excited from a single radio frequency source, with one cavity directly coupled to the source and the other cavity coupled through a delay line of special construction. A phase detector provides a bipolar d-c output signal proportional to the difference in phase between the voltage in the two cavities. This d-c signal controls a bias supply which provides a d-c output for varying the capacitnce of voltage sensitive capacitors in the delay line. The over-all operation of the circuit is completely electronic, overcoming the time response limitations of the electromechanical control systems, and the relative phase relationship of the radio frequency voltages in the two caviiies is continuously controlled to effect particle acceleration.

  10. JPL Contamination Control Engineering

    NASA Technical Reports Server (NTRS)

    Blakkolb, Brian

    2013-01-01

    JPL has extensive expertise fielding contamination sensitive missions-in house and with our NASA/industry/academic partners.t Development and implementation of performance-driven cleanliness requirements for a wide range missions and payloads - UV-Vis-IR: GALEX, Dawn, Juno, WFPC-II, AIRS, TES, et al - Propulsion, thermal control, robotic sample acquisition systems. Contamination control engineering across the mission life cycle: - System and payload requirements derivation, analysis, and contamination control implementation plans - Hardware Design, Risk trades, Requirements V-V - Assembly, Integration & Test planning and implementation - Launch site operations and launch vehicle/payload integration - Flight ops center dot Personnel on staff have expertise with space materials development and flight experiments. JPL has capabilities and expertise to successfully address contamination issues presented by space and habitable environments. JPL has extensive experience fielding and managing contamination sensitive missions. Excellent working relationship with the aerospace contamination control engineering community/.

  11. NEWS: Feeling in control?

    NASA Astrophysics Data System (ADS)

    2000-05-01

    Windmill Graphics simulation software has been developed to help explain control technology to students. The software allows an engineering process such as might be found in the oil or gas industry to be controlled from a PC through simulations of closing drain valves, filling tanks, starting heating operations etc. Other tasks include using level control systems with digital sensors, temperature control with digital and analogue sensors and monitoring systems plus datalogging. The kit was funded by the Scottish Higher Still Development Unit and it has been distributed to all secondary schools, further education colleges and teacher training institutes in Scotland. It will also in turn be distributed to all schools in England, but in the meantime free copies can be downloaded from: www.windmill.co.uk/wmldemo.html

  12. Controlled Cardiac Computed Tomography

    PubMed Central

    Wang, Chenglin; Liu, Ying; Wang, Ge

    2006-01-01

    Cardiac computed tomography (CT) has been a hot topic for years because of the clinical importance of cardiac diseases and the rapid evolution of CT systems. In this paper, we propose a novel strategy for controlled cardiac CT that may effectively reduce image artifacts due to cardiac and respiratory motions. Our approach is radically different from existing ones and is based on controlling the X-ray source rotation velocity and powering status in reference to the cardiac motion. We theoretically show that by such a control-based intervention the data acquisition process can be optimized for cardiac CT in the cases of periodic and quasiperiodic cardiac motions. Specifically, we formulate the corresponding coordination/control schemes for either exact or approximate matches between the ideal and actual source positions, and report representative simulation results that support our analytic findings. PMID:23165017

  13. Active control of convection

    SciTech Connect

    Bau, H.H.

    1995-12-31

    Using stability theory, numerical simulations, and in some instances experiments, it is demonstrated that the critical Rayleigh number for the bifurcation (1) from the no-motion (conduction) state to the motion state and (2) from time-independent convection to time-dependent, oscillatory convection in the thermal convection loop and Rayleigh-Benard problems can be significantly increased or decreased. This is accomplished through the use of a feedback controller effectuating small perturbations in the boundary data. The controller consists of sensors which detect deviations in the fluid`s temperature from the motionless, conductive values and then direct actuators to respond to these deviations in such a way as to suppress the naturally occurring flow instabilities. Actuators which modify the boundary`s temperature/heat flux are considered. The feedback controller can also be used to control flow patterns and generate complex dynamic behavior at relatively low Rayleigh numbers.

  14. Vapor Control Layer Recommendations

    SciTech Connect

    2009-09-08

    This information sheet describes the level of vapor control required on the interior side of framed walls with typical fibrous cavity insulation (fibreglass, rockwool, or cellulose, based on DOE climate zone of construction.

  15. Computer controlled antenna system

    NASA Technical Reports Server (NTRS)

    Raumann, N. A.

    1972-01-01

    Digital techniques are discussed for application to the servo and control systems of large antennas. The tracking loop for an antenna at a STADAN tracking site is illustrated. The augmentation mode is also considered.

  16. Advances in infection control

    PubMed Central

    Marra, Alexandre Rodrigues

    2016-01-01

    ABSTRACT Several initiatives took place in recent years in relation to nosocomial infection control in order to increase patient safety. Some of these initiatives will be commented in this brief review. PMID:27074240

  17. Cryogenic Control System

    SciTech Connect

    Goloborod'ko, S.; /Fermilab

    1989-02-27

    The control system (CS) for the cryogenic arrangement of the DO Liquid Argon Calorimeter consists of a Texas instruments 560/565 Programmable Logical Controller (PLC), two remote bases with Remote Base Controllers and a corresponding set of input/output (I/O) modules, and a PC AST Premium 286 (IBM AT Compatible). The PLC scans a set of inputs and provides a set of outputs based on a ladder logic program and PID control loops. The inputs are logic or analog (current, voltage) signals from equipment status switches or transducers. The outputs are logic or analog (current or voltage) signals for switching solenoids and positioning pneumatic actuators. Programming of the PLC is preformed by using the TISOFT2/560/565 package, which is installed in the PC. The PC communicates to the PLC through a serial RS232 port and provides operator interface to the cryogenic process using Xpresslink software.

  18. Birth control pills - combination

    MedlinePlus

    The pill - combination; Oral contraceptives - combination; OCP - combination; Contraception - combination; BCP - combination ... Birth control pills help keep you from getting pregnant. When taken daily, they are one of the most ...

  19. Linear Hereditary Control Systems,

    DTIC Science & Technology

    Relationships between external and internal models for systems with time lags are discussed. The use of various canonical forms for the models in solving optimal control problems is considered. (Author)

  20. Surface Enhanced Quantum Control

    NASA Astrophysics Data System (ADS)

    Rangan, Chitra

    2013-05-01

    Miniaturization of quantum technologies have led to physics that require the marriage of atomic physics and nanomaterials science. Some of the resulting areas of research are hybrid quantum devices, single-molecule spectroscopies, table-top intense field generators, etc. I will present an area of research that I dub ``Surface-enhanced quantum control'' that is an exciting way of controlling light and nanomatter. By combining the electromagnetic enhancement properties of plasmonic nanomaterials with the modification of the atomic properties, we can achieve an unprecedented level of control over quantum dynamics. I will present examples of surface-enhanced state purification, in which quantum states near metal nanostructures can be rapidly purified by the application of a weak near-resonant control field. We gratefully acknowledge support from the NSERC Discovery Grant Program and the NSERC Strategic Network for Bioplasmonic Systems.

  1. Ferroelectric Light Control Device

    NASA Technical Reports Server (NTRS)

    Park, Yeonjoon (Inventor); Choi, Sang H. (Inventor); King, Glen C. (Inventor); Kim, Jae-Woo (Inventor); Elliott, Jr., James R. (Inventor)

    2008-01-01

    A light control device is formed by ferroelectric material and N electrodes positioned adjacent thereto to define an N-sided regular polygonal region or circular region there between where N is a multiple of four.

  2. Cairo: repackaging population control.

    PubMed

    Simons, H

    1995-01-01

    Aid agencies, charities, and other nongovernmental organizations once denounced population control programs as racist interference in the third world. Yet, at the United Nations Conference on Population and Development in Cairo last September, these same organizations endorsed very similar ideas. The U.N. can now claim that even its fiercest critics not only have muted their criticism of population control programs but now positively endorse them. Over the last 30 years, population control has been consciously repackaged by the U.S. establishment. The image of population control has changed from being overtly anti-third world to being about giving the people of the third world--especially women--basic rights in family planning. Wrapped up in the language of women's empowerment and environmentalism, the establishment's old arguments about there being too many nonwhite babies in the world, have, unfortunately, won the day.

  3. Telerobot control system

    NASA Technical Reports Server (NTRS)

    Backes, Paul G. (Inventor); Tso, Kam S. (Inventor)

    1993-01-01

    This invention relates to an operator interface for controlling a telerobot to perform tasks in a poorly modeled environment and/or within unplanned scenarios. The telerobot control system includes a remote robot manipulator linked to an operator interface. The operator interface includes a setup terminal, simulation terminal, and execution terminal for the control of the graphics simulator and local robot actuator as well as the remote robot actuator. These terminals may be combined in a single terminal. Complex tasks are developed from sequential combinations of parameterized task primitives and recorded teleoperations, and are tested by execution on a graphics simulator and/or local robot actuator, together with adjustable time delays. The novel features of this invention include the shared and supervisory control of the remote robot manipulator via operator interface by pretested complex tasks sequences based on sequences of parameterized task primitives combined with further teleoperation and run-time binding of parameters based on task context.

  4. Insecticides and Biological Control

    ERIC Educational Resources Information Center

    Furness, G. O.

    1972-01-01

    Use of insecticides has been questioned due to their harmful effects on edible items. Biological control of insects along with other effective practices for checking spread of parasites on crops are discussed. (PS)

  5. Technologies for Legionella Control

    EPA Science Inventory

    Presentation includes a review of new Office of Water document entitled "Technologies for Legionella Control in Premise Plumbing Systems", and discussion on ORD research projects involving Legionella and disinfection.

  6. Tight Diabetes Control

    MedlinePlus

    ... Size: A A A Listen En Español Tight Diabetes Control Keeping your blood glucose levels as close ... and syringes, than before. What About Type 2 Diabetes? The DCCT studied only people with type 1 ...

  7. Thermal control canister

    NASA Technical Reports Server (NTRS)

    Ollendorf, S. (Inventor)

    1979-01-01

    An apparatus for maintaining a heat dissipating load at a substantially constant temperature, and more particularly, to such an apparatus where in variable conductance heat pipes control the radiating area of a radiator is described.

  8. Birth control after 1984.

    PubMed

    Djerassi, C

    1970-09-04

    1) Eric Blair (alias George Orwell) can rest easy in his grave, because birth control by governmentally imposed methods, such as incorporation of a contraceptive agent into drinking water, is totally unfeasible by 1984. 2) Fundamentally new birth control procedures in the female (for example, a once-a-month luteolytic or abortifacient agent) and a male contraceptive pill probably will not be developed until the 1980's at the earliest, and then only if major steps of the type outlined in this article are instituted in the early 1970's. Development during the next decade of practical new methods of birth control without important incentives for continued active participation by the pharmaceutical industry is highly unlikely. If none are developed, birth control in 1984 will not differ significantly from that of today.

  9. Soviet Mission Control Center

    NASA Technical Reports Server (NTRS)

    2003-01-01

    This photo is an overall view of the Mission Control Center in Korolev, Russia during the Expedition Seven mission. The Expedition Seven crew launched aboard a Soyez spacecraft on April 26, 2003. Photo credit: NASA/Bill Ingalls

  10. Control system testing

    NASA Astrophysics Data System (ADS)

    Whittler, W. H.; Collart, R. E.

    1984-08-01

    A three stage process of ground testing of the Space Telescope Pointing Control System is used for verification prior to on-orbit operation. First, development tests are conducted in a laboratory environment using flight/engineering model control sensor and actuators configured with an engineering model of the flight computer and data management system breadboards. These development tests validate the results of computer simulations predicting control system performance. Integration tests bring together flight system elements and software interfaced to a software simulation of vehicle dynamics to confirm closed loop performance. The final ground test phase, flight systems testing, is conducted on the fully assembled Space Telescope, verifies interfaces with the Fine Guidance Sensors and includes a thermal vacuum testing period. During the final test phase, the Point Control System is exercised with the dynamics simulator running in real time.

  11. Solid state power controllers

    NASA Technical Reports Server (NTRS)

    Gibbs, R. S.

    1973-01-01

    The rationale, analysis, design, breadboarding and testing of the incremental functional requirements are reported that led to the development of prototype 1 and 5 Amp dc and 1 Amp ac solid state power controllers (SSPC's). The SSPC's are to be considered for use as a replacement of electro-mechanical relays and circuit breakers in future spacecraft and aircraft. They satisfy the combined function of both the relay and circuit breaker and can be remotely controlled by small signals, typically 10 mA, 5 to 28 Vdc. They have the advantage over conventional relay/circuit breaker systems in that they can be located near utilization equipment and the primary ac or dc bus. The low level control, trip indication and status signals can be circuited by small guage wire for control, computer interface, logic, electrical multiplexing, unboard testing, and power management and distribution purposes. This results in increased system versatility at appreciable weight saving and increased reliability.

  12. Model-free control

    NASA Astrophysics Data System (ADS)

    Fliess, Michel; Join, Cédric

    2013-12-01

    'Model-free control'and the corresponding 'intelligent' PID controllers (iPIDs), which already had many successful concrete applications, are presented here for the first time in an unified manner, where the new advances are taken into account. The basics of model-free control is now employing some old functional analysis and some elementary differential algebra. The estimation techniques become quite straightforward via a recent online parameter identification approach. The importance of iPIs and especially of iPs is deduced from the presence of friction. The strange industrial ubiquity of classic PIDs and the great difficulty for tuning them in complex situations is deduced, via an elementary sampling, from their connections with iPIDs. Several numerical simulations are presented which include some infinite-dimensional systems. They demonstrate not only the power of our intelligent controllers but also the great simplicity for tuning them.

  13. Advances in Process Control.

    ERIC Educational Resources Information Center

    Morrison, David L.; And Others

    1982-01-01

    Advances in electronics and computer science have enabled industries (pulp/paper, iron/steel, petroleum/chemical) to attain better control of their processes with resulting increases in quality, productivity, profitability, and compliance with government regulations. (JN)

  14. Mission Control Roses

    NASA Video Gallery

    The 110th bouquet of roses arrived in Mission Control on Saturday, July 9, 2011. They were sent as quietly as they have been for more than 23 years by a family near Dallas, Texas. For 110 shuttle m...

  15. Robust Adaptive Control

    NASA Technical Reports Server (NTRS)

    Narendra, K. S.; Annaswamy, A. M.

    1985-01-01

    Several concepts and results in robust adaptive control are are discussed and is organized in three parts. The first part surveys existing algorithms. Different formulations of the problem and theoretical solutions that have been suggested are reviewed here. The second part contains new results related to the role of persistent excitation in robust adaptive systems and the use of hybrid control to improve robustness. In the third part promising new areas for future research are suggested which combine different approaches currently known.

  16. Neural Architectures for Control

    NASA Technical Reports Server (NTRS)

    Peterson, James K.

    1991-01-01

    The cerebellar model articulated controller (CMAC) neural architectures are shown to be viable for the purposes of real-time learning and control. Software tools for the exploration of CMAC performance are developed for three hardware platforms, the MacIntosh, the IBM PC, and the SUN workstation. All algorithm development was done using the C programming language. These software tools were then used to implement an adaptive critic neuro-control design that learns in real-time how to back up a trailer truck. The truck backer-upper experiment is a standard performance measure in the neural network literature, but previously the training of the controllers was done off-line. With the CMAC neural architectures, it was possible to train the neuro-controllers on-line in real-time on a MS-DOS PC 386. CMAC neural architectures are also used in conjunction with a hierarchical planning approach to find collision-free paths over 2-D analog valued obstacle fields. The method constructs a coarse resolution version of the original problem and then finds the corresponding coarse optimal path using multipass dynamic programming. CMAC artificial neural architectures are used to estimate the analog transition costs that dynamic programming requires. The CMAC architectures are trained in real-time for each obstacle field presented. The coarse optimal path is then used as a baseline for the construction of a fine scale optimal path through the original obstacle array. These results are a very good indication of the potential power of the neural architectures in control design. In order to reach as wide an audience as possible, we have run a seminar on neuro-control that has met once per week since 20 May 1991. This seminar has thoroughly discussed the CMAC architecture, relevant portions of classical control, back propagation through time, and adaptive critic designs.

  17. Supercavitating Vehicle Control

    DTIC Science & Technology

    2008-10-10

    herein as winglets , are supported by a strut attached to the vehicle. The angle of attack of each winglet is controlled by a winglet actuator. The... winglet assembly may be extended into or retracted from the water by means of a spring-loaded actuated mount, which pivots the strut supporting the... winglet . When fully retracted, the winglet assembly is contained completely within the cavity. [0014] The segmented ring wing is controlled by one or more

  18. Understanding Command and Control

    DTIC Science & Technology

    2006-01-01

    and Control are fractal concepts. They can be applied to all subsets of an enterprise; to the functions performed; to the levels of the organizations...to the focus of the activity, whether strategic or tactical. Membership in these fractals may overlap with individual entities and groups...belonging to multiple fractals dynamically. • Different Command and Control Approaches will be appropriate for different sets of purposes or circumstances

  19. JPRS Report, Arms Control.

    DTIC Science & Technology

    2007-11-02

    automated control systems, computerized complexes, high-speed computers capable of millions of operations a second and having a formidable memory; we have...be, since we do not yet know the number of tranports : how many lorries and what type. [Reporter] Will the Polish side have any control whatso... technology to Iraq when the Gulf crisis erupted. After stating that Brazil has no chemical weapons, Rezek justified the agreement. Rezek said: It is

  20. Test Control Center exhibit

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Have you ever wondered how the engineers at John C. Stennis Space Center in Hancock County, Miss., test fire a Space Shuttle Main Engine? The Test Control Center exhibit at StenniSphere can answer your questions by simulating the test firing of a Space Shuttle Main Engine. A recreation of one of NASA's test control centers, the exhibit explains and portrays the 'shake, rattle and roar' that happens during a real test firing.

  1. Drone Control System

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Drones, subscale vehicles like the Firebees, and full scale retired military aircraft are used to test air defense missile systems. The DFCS (Drone Formation Control System) computer, developed by IBM (International Business Machines) Federal Systems Division, can track ten drones at once. A program called ORACLS is used to generate software to track and control Drones. It was originally developed by Langley and supplied by COSMIC (Computer Software Management and Information Center). The program saved the company both time and money.

  2. GPS Control Segment Improvements

    DTIC Science & Technology

    2015-04-29

    Systems Center GPS Control Segment Improvements Mr. Tim McIntyre GPS Product Support Manager GPS Ops Support and Sustainment Division Peterson...hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and...DATE 29 APR 2015 2. REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE GPS Control Segment Improvements 5a. CONTRACT

  3. TACS Central Control Facility.

    DTIC Science & Technology

    1981-02-12

    Central Control Facility 6 3. System Management Data Flow 7 B. Hardware Operating Environment 9 1. Computer 9 2. TACS Interfaces 9 3. Other Central...TERMINATION TIMING 131 Appendix C SYSTEM MANAGEMENT DATA FORMATS 135 Appendix D FIVE- AND NINE-SLOT SYSTEM IMPLEMENTATION DIFFERENCES 147 Appendix E...control burst management ) 26 2-7 Call Progress Messages 29 2-8 Flowchart of Assignment/Blockage Decision Process for All-Member Net Requests 30 2-9

  4. GPS Control Segment

    DTIC Science & Technology

    2015-04-29

    AND MISSILE SYSTEMS CENTER • Provides GPS Ill SV command and control • NAV capability equivalent to GPS IIF (legacy and modern signals) - No L 1 ...Public reporting burden for the collection of information is estimated to average 1 hour per response, including the time for reviewing instructions...information if it does not display a currently valid OMB control number 1 . REPORT DATE 29 APR 2015 2. REPORT TYPE 3. DATES COVERED 00-00-2015 to 00

  5. Digital flight control research

    NASA Technical Reports Server (NTRS)

    Potter, J. E.; Stern, R. G.; Smith, T. B.; Sinha, P.

    1974-01-01

    The results of studies which were undertaken to contribute to the design of digital flight control systems, particularly for transport aircraft are presented. In addition to the overall design considerations for a digital flight control system, the following topics are discussed in detail: (1) aircraft attitude reference system design, (2) the digital computer configuration, (3) the design of a typical digital autopilot for transport aircraft, and (4) a hybrid flight simulator.

  6. Adaptive and Nonlinear Control

    DTIC Science & Technology

    1992-02-29

    in [22], we also applied the concept of zero dynamics to the problem of exact linearization of a nonlinear control system by dynamic feedback. Exact ...nonlinear systems, although it was well-known that the conditions for exact linearization are very stringent and consequently do not apply to a broad...29th IEEE Conference n Decision and Control, Invited Paper delivered by Dr. Gilliam. Exact Linearization of Zero Dynamics, 29th IEEE Conference on

  7. Flight Trajectory Control Investigation

    DTIC Science & Technology

    1981-03-01

    control algorithms for four-dimensional guidance of a transport air- craft were investigated for feasibility. Cost function constraints on the ptimal...21 3.1.6 Solution Constraints .... ............. ... 25 3.1.7 Trajectory Generator Review .. ......... .. 25 3.2 OPTIMAl CONTROLLER ALGORITHM...value formulation to a six-degree-of-freedom point mass aircraft with all the structural, maneuver, and mission constraints accounted for by using pelalty

  8. Thoracic damage control surgery.

    PubMed

    Gonçalves, Roberto; Saad, Roberto

    2016-01-01

    The damage control surgery came up with the philosophy of applying essential maneuvers to control bleeding and abdominal contamination in trauma patients who are within the limits of their physiological reserves. This concept was extended to thoracic injuries, where relatively simple maneuvers can shorten operative time of in extremis patients. This article aims to revise the various damage control techniques in thoracic organs that must be known to the surgeon engaged in emergency care. RESUMO A cirurgia de controle de danos surgiu com a filosofia de se aplicar manobras essenciais para controle de sangramento e contaminação abdominal, em doentes traumatizados, nos limites de suas reservas fisiológicas. Este conceito se estendeu para as lesões torácicas, onde manobras relativamente simples, podem abreviar o tempo operatório de doentes in extremis. Este artigo tem como objetivo, revisar as diversas técnicas de controle de dano em órgãos torácicos, que devem ser de conhecimento do cirurgião que atua na emergência.

  9. Failure of chaos control

    PubMed

    van De Water W; de Weger J

    2000-11-01

    We study the control of chaos in an experiment on a parametrically excited pendulum whose excitation mechanism is not perfect. This imperfection leads to a weakly excited degree of freedom with an associated small eigenvalue. Although the state of the pendulum could be characterized well and although the perturbation is weak, we fail to control chaos. From a numerical model we learn that the small eigenvalue cannot be ignored when attempting control. However, the estimate of this eigenvalue from an (experimental) time series is elusive. The reason is that points in an experimental time series are distributed according to the natural measure. It is this extremely uneven distribution of points that thwarts attempts to measure eigenvalues that are very different. Another consequence of the phase-space distribution of points for control is the occurrence of logarithmic-oscillations in the waiting time before control can be attempted. We come to the conclusion that chaos needs to be destroyed before the information needed for its control can be obtained.

  10. Pit disassembly motion control

    SciTech Connect

    Christensen, L.; Pittman, P. C.

    2001-01-01

    A Department of Energy (DOE) Pit Disassembly and Conversion Facility (PDCF) is being designed for the Savannah River Site in South Carolina. The facility will recover plutonium from excess nuclear weapon pits defined in START II and START III treaties. The plutonium will be stored and used to produce mixed oxide reactor fuel at another new DOE facility. Because of radiation dose issues, much of the pit disassembly work and material transfer will be automated. Automated material handling systems will interface with disassembly lathes, conversion reactors that produce oxide for storage, robotic container welding stations, vault retrieval systems, and nondestructive assay (NDA) instrumentation. The goal is to use common motion control hardware for material transfer and possibly common motion controllers for the unique PDCF systems. The latter is complicated by the different directions manufactures are considering for distributed control, such as Firewire, SERCOS, etc., and by the unique control requirements of machines such as lathes compared to controls for an integrated NDA system. The current design approach is to standardize where possible, use network cables to replace wire bundles where possible, but to first select hardware and motion controllers that meet specific machine or process requirements.

  11. Integrated airframe propulsion control

    NASA Technical Reports Server (NTRS)

    Fennell, R. E.; Black, S. B.

    1982-01-01

    Perturbation equations which describe flight dynamics and engine operation about a given operating point are combined to form an integrated aircraft/propulsion system model. Included in the model are the dependence of aerodynamic coefficients upon atmospheric variables along with the dependence of engine variables upon flight condition and inlet performance. An off-design engine performance model is used to identify interaction parameters in the model. Inclusion of subsystem interaction effects introduces coupling between flight and propulsion variables. To analyze interaction effects on control, consideration is first given to control requirements for separate flight and engine models. For the separate airframe model, feedback control provides substantial improvement in short period damping. For the integrated system, feedback control compensates for the coupling present in the model and provides good overall system stability. However, this feedback control law involves many non-zero gains. Analysis of suboptimal control strategies indicates that performance of the closed loop integrated system can be maintained with a feedback matrix in which the number of non-zero gains is small relative to the number of components in the feedback matrix.

  12. Optical beam jitter control

    NASA Astrophysics Data System (ADS)

    Watkins, R. Joseph; Chen, Hong-Jen; Agrawal, Brij N.; Shin, Young S.

    2004-06-01

    For several future imaging and communications spacecraft, a challenging area of technology development is the fine acquisition, tracking, and pointing (ATP) control of the spacecraft and its payload. For example, some spacecraft with large aperture(s) in the range of 10~30 m diameter requires a few arc-seconds accuracy, 10~15 nano-radians jitter, and a fast slewing rate to acquire the target. Furthermore these stringent requirements are at risk of great structure and control interactions. This paper we will focus on the control of optical beam jitter. A Laser Jitter Control (LJC) testbed has been constructed to test jitter algorithms. The testbed consists of two fast steering mirrors (FSM), three position sensing modules (PSM), one diode laser, and several beam splitters and mirrors, all on an isolated Newport optical bench. Jitter is injected with one FSM and the other FSM is used to control it. The jitter spectrum, representing the on-orbit spacecraft and beam jitter environment, contains not only narrow band noise due to rotating devices such as gyroscopes and reaction wheels but also broadband noise. The performance of a Wiener Filter-adaptive algorithm with ideal reference signal is established as the baseline for comparison of adaptive control methods in suppressing both broadband and narrowband disturbances. Specifically, the Least Mean Squares (LMS) approach and the Gradient Adaptive Lattice (GAL) approach are investigated during these experiments.

  13. Space Shuttle flight control system

    NASA Technical Reports Server (NTRS)

    Klinar, W. J.; Kubiak, E. T.; Peters, W. H.; Saldana, R. L.; Smith, E. E., Jr.; Stegall, H. W.

    1975-01-01

    The Space Shuttle is a control stabilized vehicle with control provided by an all digital, fly-by-wire flight control system. This paper gives a description of the several modes of flight control which correspond to the Shuttle mission phases. These modes are ascent flight control (including open loop first stage steering, the use of four computers operating in parallel and inertial guidance sensors), on-orbit flight control (with a discussion of reaction control, phase plane switching logic, jet selection logic, state estimator logic and OMS thrust vector control), entry flight control and TAEM (terminal area energy management to landing). Also discussed are redundancy management and backup flight control.

  14. Controlled Quantum Packets

    NASA Technical Reports Server (NTRS)

    DeMartino, Salvatore; DeSiena, Silvio

    1996-01-01

    We look at time evolution of a physical system from the point of view of dynamical control theory. Normally we solve motion equation with a given external potential and we obtain time evolution. Standard examples are the trajectories in classical mechanics or the wave functions in Quantum Mechanics. In the control theory, we have the configurational variables of a physical system, we choose a velocity field and with a suited strategy we force the physical system to have a well defined evolution. The evolution of the system is the 'premium' that the controller receives if he has adopted the right strategy. The strategy is given by well suited laboratory devices. The control mechanisms are in many cases non linear; it is necessary, namely, a feedback mechanism to retain in time the selected evolution. Our aim is to introduce a scheme to obtain Quantum wave packets by control theory. The program is to choose the characteristics of a packet, that is, the equation of evolution for its centre and a controlled dispersion, and to give a building scheme from some initial state (for example a solution of stationary Schroedinger equation). It seems natural in this view to use stochastic approach to Quantum Mechanics, that is, Stochastic Mechanics [S.M.]. It is a quantization scheme different from ordinary ones only formally. This approach introduces in quantum theory the whole mathematical apparatus of stochastic control theory. Stochastic Mechanics, in our view, is more intuitive when we want to study all the classical-like problems. We apply our scheme to build two classes of quantum packets both derived generalizing some properties of coherent states.

  15. Supervisory Control Strategy Development

    SciTech Connect

    Gary D. Storrick; Bojan Petrovic

    2007-02-28

    Task 4 of this collaborative effort between ORNL, Brazil, and Westinghouse for the International Nuclear Energy Research Initiative entitled “Development of Advanced Instrumentation and Control for an Integrated Primary System Reactor” focused on the design of the hierarchical supervisory control for multiple-module units. The state of the IRIS plant design – specifically, the lack of a detailed secondary system design – made developing a detailed hierarchical control difficult at this time. However, other simultaneous and ongoing efforts have contributed to providing the needed information. This report summarizes the results achieved under Task 4 of this Financial Assistance Award. Section 1.2 describes the scope of this effort. Section 2 discusses the IRIS control functions. Next, it briefly reviews the current control concepts, and then reviews the maneuvering requirements for the IRIS plant. It closes by noting the benefits that automated sequences have in reducing operator workload. Section 3 examines reactor loading in the frequency domain to establish some guidelines for module operation, paying particular attention to strategies for using process steam for desalination and/or district heating. The final subsection discusses the implications for reactor control, and argues that using the envisioned percentage (up to 10%) of the NSSS thermal output for these purposes should not significantly affect the NSSS control strategies. Section 4 uses some very general economic assumptions to suggest how one should approach multi-module operation. It concludes that the well-known algorithms used for economic dispatching could be used to help manage a multi-unit IRIS site. Section 5 addresses the human performance factors of multi-module operation. Section 6 summarizes our conclusions.

  16. Aligning Task Control with Desire for Control: Implications for Performance

    PubMed Central

    Ramsey, Alex T.; Etcheverry, Paul E.

    2015-01-01

    The current study examined whether matches between task control and participants' desire for control over their environment lead to better task performance than mismatches. Work control and desire for control were manipulated, and participants engaged in timed tasks. As predicted, performance was higher in cases of match, even when task control and desire for control were low. Task control and desire for control may predict work performance in combination, highlighting the importance of Person-Environment Fit theory for both selection and work design. By manipulating desire for control, our research also explores the potentially state-dependent quality of this individual difference variable. PMID:26045630

  17. Aligning Task Control with Desire for Control: Implications for Performance.

    PubMed

    Ramsey, Alex T; Etcheverry, Paul E

    The current study examined whether matches between task control and participants' desire for control over their environment lead to better task performance than mismatches. Work control and desire for control were manipulated, and participants engaged in timed tasks. As predicted, performance was higher in cases of match, even when task control and desire for control were low. Task control and desire for control may predict work performance in combination, highlighting the importance of Person-Environment Fit theory for both selection and work design. By manipulating desire for control, our research also explores the potentially state-dependent quality of this individual difference variable.

  18. 13. CONTROL ROOM OF GENE PUMPING STATION. CONTROL CUBICLES ARRAYED ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. CONTROL ROOM OF GENE PUMPING STATION. CONTROL CUBICLES ARRAYED BEHIND MANAGER'S ART DECO-STYLE CONTROL DESK, WITH CONTROL CUBICLE 1 AT FAR RIGHT AND CONTROL CUBICLE 9 AT FAR LEFT. - Gene Pump Plant, South of Gene Wash Reservoir, 2 miles west of Whitsett Pump Plant, Parker Dam, San Bernardino County, CA

  19. Resource Balancing Control Allocation

    NASA Technical Reports Server (NTRS)

    Frost, Susan A.; Bodson, Marc

    2010-01-01

    Next generation aircraft with a large number of actuators will require advanced control allocation methods to compute the actuator commands needed to follow desired trajectories while respecting system constraints. Previously, algorithms were proposed to minimize the l1 or l2 norms of the tracking error and of the control effort. The paper discusses the alternative choice of using the l1 norm for minimization of the tracking error and a normalized l(infinity) norm, or sup norm, for minimization of the control effort. The algorithm computes the norm of the actuator deflections scaled by the actuator limits. Minimization of the control effort then translates into the minimization of the maximum actuator deflection as a percentage of its range of motion. The paper shows how the problem can be solved effectively by converting it into a linear program and solving it using a simplex algorithm. Properties of the algorithm are investigated through examples. In particular, the min-max criterion results in a type of resource balancing, where the resources are the control surfaces and the algorithm balances these resources to achieve the desired command. A study of the sensitivity of the algorithms to the data is presented, which shows that the normalized l(infinity) algorithm has the lowest sensitivity, although high sensitivities are observed whenever the limits of performance are reached.

  20. Electronically controlled automatic transmission

    SciTech Connect

    Ohkubo, M.; Shiba, H.; Nakamura, K.

    1989-03-28

    This patent describes an electronically controlled automatic transmission having a manual valve working in connection with a manual shift lever, shift valves operated by solenoid valves which are driven by an electronic control circuit previously memorizing shift patterns, and a hydraulic circuit controlled by these manual valve and shift valves for driving brakes and a clutch in order to change speed. Shift patterns of 2-range and L-range, in addition to a shift pattern of D-range, are memorized previously in the electronic control circuit, an operation switch is provided which changes the shift pattern of the electronic control circuit to any shift pattern among those of D-range, 2-range and L-range at time of the manual shift lever being in a D-range position, a releasable lock mechanism is provided which prevents the manual shift lever from entering 2-range and L-range positions, and the hydraulic circuit is set to a third speed mode when the manual shift lever is in the D-range position. The circuit is set to a second speed mode when it is in the 2-range position, and the circuit is set to a first speed mode when it is in the L-range position, respectively, in case where the shift valves are not working.

  1. A tactile control prosthesis

    NASA Astrophysics Data System (ADS)

    Perry, James Franklin

    This research involves development and testing of a tactile control prosthesis to aid human operators in control of dynamic vehicles. Specifically, this work includes development and demonstration of a torso mounted tactile drift display that allowed helicopter pilots to hover a Blackhawk helicopter with degraded vision (equivalent to 20/200 acuity), a NASA sponsored pilot-in-the-loop simulator study for a hover display and development and analysis of a tactile control prosthesis to help pilots correctly control an airplane experiencing an engine failure on takeoff. Results of a ten-subject experiment indicate that use of a tactile display in conjunction with a visual display reduces operator delay by 65 msec (SD of 28 msec), (P < 0.001) without a significant increase in error rate. In the pilot-in-the-loop simulation experiment pilots hovered a simulated helicopter better under increased workload conditions with the tactile control prosthesis than without it. The increased workload consisted of an addition drill in which the subject had to agree or disagree with a computer generated sum. Pilots were able to hover more precisely with the tactile display (mean of 5.19, SD of 2.57 feet) than without (mean of 6.39 and SD of 3.31 feet) especially when the secondary task was required (P < 0.001). Although learning effects were exhibited throughout the trials (P < 0.001), the tactile display was of greater benefit in higher workload conditions.

  2. Laser Ion Acceleration Control

    NASA Astrophysics Data System (ADS)

    Kawata, Shigeo; Nagashima, T.; Izumiyama, T.; Sato, D.; Takano, M.; Barada, D.; Ma, Y. Y.; Gu, Y. J.; Kong, Q.; Wang, P. X.; Wang, W. M.

    2013-10-01

    An intense femtosecond pulsed laser is employed to accelerate ions. The issues in the laser ion accelerator include the energy efficiency from the laser to the ions, the ion beam collimation, the ion energy spectrum control, the ion beam bunching, the ion particle energy control, etc. In the study particle computer simulations were performed to solve the issues, and each component was designed to control the ion beam quality. When an intense laser illuminates a target, electrons in the target are accelerated and leave from the target; temporarily a strong electric field is formed between the high-energy electrons and the target ions, and the target ions are accelerated. The energy efficiency from the laser to ions was improved by using a solid target with a fine sub-wavelength structure or by a near critical density gas plasma. The ion beam collimation was realized by holes behind the solid target. The control of the ion energy spectrum and the ion particle energy, and the ion beam bunching were successfully realized by a multi-stage laser-target interaction. The present study proposed a novel concept for a future compact laser ion accelerator, based on each component study required to control the ion beam quality and parameters. Partly supported by JSPS, MEXT, CORE, Japan/US Cooperation program, ASHULA and ILE/Osaka University.

  3. Tobacco control in India.

    PubMed

    Shimkhada, Riti; Peabody, John W

    2003-01-01

    Legislation to control tobacco use in developing countries has lagged behind the dramatic rise in tobacco consumption. India, the third largest grower of tobacco in the world, amassed 1.7 million disability-adjusted life years (DALYs) in 1990 due to disease and injury attributable to tobacco use in a population where 65% of the men and 38% of the women consume tobacco. India's anti-tobacco legislation, first passed at the national level in 1975, was largely limited to health warnings and proved to be insufficient. In the last decade state legislation has increasingly been used but has lacked uniformity and the multipronged strategies necessary to control demand. A new piece of national legislation, proposed in 2001, represents an advance. It includes the following key demand reduction measures: outlawing smoking in public places; forbidding sale of tobacco to minors; requiring more prominent health warning labels; and banning advertising at sports and cultural events. Despite these measures, the new legislation will not be enough to control the demand for tobacco products in India. The Indian Government must also introduce policies to raise taxes, control smuggling, close advertising loopholes, and create adequate provisions for the enforcement of tobacco control laws.

  4. Nuclear reactor control column

    DOEpatents

    Bachovchin, Dennis M.

    1982-01-01

    The nuclear reactor control column comprises a column disposed within the nuclear reactor core having a variable cross-section hollow channel and containing balls whose vertical location is determined by the flow of the reactor coolant through the column. The control column is divided into three basic sections wherein each of the sections has a different cross-sectional area. The uppermost section of the control column has the greatest cross-sectional area, the intermediate section of the control column has the smallest cross-sectional area, and the lowermost section of the control column has the intermediate cross-sectional area. In this manner, the area of the uppermost section can be established such that when the reactor coolant is flowing under normal conditions therethrough, the absorber balls will be lifted and suspended in a fluidized bed manner in the upper section. However, when the reactor coolant flow falls below a predetermined value, the absorber balls will fall through the intermediate section and into the lowermost section, thereby reducing the reactivity of the reactor core and shutting down the reactor.

  5. Well pump controller

    SciTech Connect

    Pikna, R. G.

    1985-04-02

    A device for automatically controlling the pumping of fluids from a well of the type using a walking beam and positive displacement pump to provide efficient utilization of the pumping equipment and energy required therefor, and to obtain efficient flow rates from the wall. A sensor detects the position of the walking beam at a predetermined position on the up-stroke of its pumping cycle and generates a signal to a control unit. a diaphram detects the pressure differential between the well casing pressure and the fluid delivery tube pressure. The diaphram moves a spring biased plunger which actuates a switch upon a predetermined pressure differential existing between the casing and delivery tube which sends a second signal to the control unit. The control unit upon receiving both signals maintains the pumping unit energizes until the pressure differential on the diaphram drops to a predetermined value preventing the plunger from actuating the switch. The control unit will deenergize the pumping unit if both signals are not received at the appropriate time. The sensitivity of the diaphram actuated switch is adjustable by changing the biasing force of the spring on the plunger.

  6. Dynamics of immigration control.

    PubMed

    Djajic, S

    1999-01-01

    This paper examines the dynamic implications of US border control policies and internal enforcement measures for the pattern of illegal immigration and the sectoral allocation of clandestine foreign workers. Efforts to counteract illegal immigration into the US have been increasing steadily following the passage of the Immigration Reform and Control Act of 1986. The purpose of the Act is to reduce illegal immigration with the aid of three instruments: 1) employer sanctions; 2) increased controls along the border; and 3) a legalization program designed to meet the existing demand for agricultural labor in geographic locations that are in proximity of Mexico, the principal source of clandestine foreign labor. The effect of tougher border control measures increases the cost of illegal entry, discouraging clandestine inflows. On the other hand, these measures induce migrants to increase their own anti-detection efforts, reducing the probability of detection and the deportation rate. If the latter effect should dominate, the steady-state stock of clandestine foreign labor will actually increase in response to more vigorous border control measures. Explicit consideration of the role of networks in the clandestine labor market suggests the need for a drastic policy change. This policy change should target illegal migration in areas with high concentrations of clandestine foreign workers. Complementary measures should accompany this policy change to prevent unbalanced enforcement measures.

  7. Aquatic plant control research

    SciTech Connect

    Pryfogle, P.A.; Rinehart, B.N.; Ghio, E.G.

    1997-05-01

    The Northwest region of the United States contains extensive canal systems that transport water for hydropower generation. Nuisance plants, including algae, that grow in these systems reduce their hydraulic capacity through water displacement and increased surface friction. Most control methods are applied in an ad hoc fashion. The goal of this work is to develop cost-effective, environmentally sound, long-term management strategies to prevent and control nuisance algal growth. This paper reports on a multi-year study, performed in collaboration with the Pacific Gas & Electric Company, to investigate algal growth in their canal systems, and to evaluate various control methodologies. Three types of controls, including mechanical, biological and chemical treatment, were selected for testing and evaluation. As part of this study, water quality data were collected and algal communities were sampled from numerous stations throughout the distribution system at regular intervals. This study resulted in a more comprehensive understanding of conditions leading to the development of nuisance algal growth, a better informed selection of treatment plans, and improved evaluation of the effectiveness for the control strategies selected for testing.

  8. Tobacco control in India.

    PubMed Central

    Shimkhada, Riti; Peabody, John W.

    2003-01-01

    Legislation to control tobacco use in developing countries has lagged behind the dramatic rise in tobacco consumption. India, the third largest grower of tobacco in the world, amassed 1.7 million disability-adjusted life years (DALYs) in 1990 due to disease and injury attributable to tobacco use in a population where 65% of the men and 38% of the women consume tobacco. India's anti-tobacco legislation, first passed at the national level in 1975, was largely limited to health warnings and proved to be insufficient. In the last decade state legislation has increasingly been used but has lacked uniformity and the multipronged strategies necessary to control demand. A new piece of national legislation, proposed in 2001, represents an advance. It includes the following key demand reduction measures: outlawing smoking in public places; forbidding sale of tobacco to minors; requiring more prominent health warning labels; and banning advertising at sports and cultural events. Despite these measures, the new legislation will not be enough to control the demand for tobacco products in India. The Indian Government must also introduce policies to raise taxes, control smuggling, close advertising loopholes, and create adequate provisions for the enforcement of tobacco control laws. PMID:12640476

  9. Control of vortex breakdown

    NASA Astrophysics Data System (ADS)

    Husain, H.; Shtern, F.; Hussain, V.

    1996-11-01

    The paper develops means of vortex breakdown (VB) control with the help of Controlling Vortex Generators (CVGs). Vortex breakdown plays the crucial role in many practical swirling flows, e.g. (a) leading-edge vortices above delta wings create a strong lift and (b) trailing vortices behind large aircraft disturbances are potentially dangerous to subsequent aircraft. It is useful to prevent VB in case (a) and to stimulate VB in case (b). We have recently obtained significant theoretical and experimental results related to swirling flow prediction and control. Firstly, a theory has been developed which models jump transitions in swirling flow (e.g. jumps in VB locations) and predicts ranges of control parameters where multiple stable states occur. Secondly, our experiments have revealed that effective control (enhancement and suppression) of VB can be achieved using CVGs. In our experiments we have used a thin rotaing rod as a CVG, placed along the axis of the basic swirling flow in a sealed cylinder driven by the rotating bottom disc. The effect of the rod depends on the direction of the rotation. With increasing rod co-rotational speed, the VB 'bubble' (VBB) becomes smaller and then disappear, and a cone-shaped wake forms. Counter-rotation of the rod causes increases VBBs' diameter and makes the flow unsteady. The VBBs begin to advect downstream, undergo tearing and pairing, and, hence, enhance mixing.

  10. Thrust-Vector-Control System

    NASA Technical Reports Server (NTRS)

    Murray, Jonathan

    1992-01-01

    Control gains computed via matrix Riccati equation. Software-based system controlling aim of gimbaled rocket motor on spacecraft adaptive and optimal in sense it adjusts control gains in response to feedback, according to optimizing algorithm based on cost function. Underlying control concept also applicable, with modifications, to thrust-vector control on vertical-takeoff-and-landing airplanes, control of orientations of scientific instruments, and robotic control systems.

  11. Macrofouling control technology update

    SciTech Connect

    Tsou, J.L.; Armor, A.F.

    1996-12-31

    Macrofouling of condenser systems with debris, fish, clams, barnacles, mussels, algae, and other marine organisms can significantly affect power plant availability and performance. Typical difficulties include increased condenser back pressure due to reduced cooling-water flow, malfunctioning of on-line tube-cleaning equipment, and accelerated corrosion and erosion of tubing. In some severe cases, condenser back pressure increased to a point that the turbine had to be tripped. In 1981 EPRI initiated a research project to develop utility industry guidelines for reducing macrofouling problems. In 1987 EPRI published the Guidelines on Macrofouling Control Technology. Since then significant progress has been made by EPRI, utility members, equipment manufacturers, and others. The purpose of this paper is to update the macrofouling control technology. Control technology covered will include thermal treatment, mechanical removal devices, antifouling coatings, and chemical treatment.

  12. Dynamic PID loop control

    SciTech Connect

    Pei, L.; Klebaner, A.; Theilacker, J.; Soyars, W.; Martinez, A.; Bossert, R.; DeGraff, B.; Darve, C.; /Fermilab

    2011-06-01

    The Horizontal Test Stand (HTS) SRF Cavity and Cryomodule 1 (CM1) of eight 9-cell, 1.3GHz SRF cavities are operating at Fermilab. For the cryogenic control system, how to hold liquid level constant in the cryostat by regulation of its Joule-Thompson JT-valve is very important after cryostat cool down to 2.0 K. The 72-cell cryostat liquid level response generally takes a long time delay after regulating its JT-valve; therefore, typical PID control loop should result in some cryostat parameter oscillations. This paper presents a type of PID parameter self-optimal and Time-Delay control method used to reduce cryogenic system parameters oscillation.

  13. SERVOMOTOR CONTROL SYSTEM

    DOEpatents

    MacNeille, S.M.

    1958-12-01

    Control systems for automatic positioning of an electric motor operated vapor valve are described which is operable under the severe conditions existing in apparatus for electro-magnetlcally separating isotopes. In general, the system includes a rotor for turning the valve comprising two colls mounted mutually perpendicular to each other and also perpendicular to the magnetic field of the isotope separating apparatus. The coils are furnished with both a-c and d- c current by assoclate control circuitry and a position control is provided for varying the ratlo of the a-c currents in the coils and at the same time, but in an inverse manner, the ratio between the d-c currents in the coils is varied. With the present system the magnitude of the motor torque is constant for all valves of the rotor orientatlon angle.

  14. Control Techtronics International

    SciTech Connect

    West, J.

    1995-12-31

    Polish graded coal can be burned in existing stoker boilers and meet the 1998 Air Quality standard. This is accomplished with the Control Techtronics microprocessor-based combustion controller accurately and repeatedly: (a) matching the combustion air to the coal firing rate, with continuous stack sensor feedback; (b) continuously varying the boiler`s firing rate based on output water temperature or steam pressure; (c) continuously varying the exhaust fan`s speed to maintain minimum negative pressure in the boiler`s combustion chamber; and recirculating a portion of the flue gas, at varying amounts throughout the boiler`s firing rate. Systems for five boilers have been installed and are operating on MPEC`s Balicka plant in Krakow. Control Techtronics International has $10 million of U.S. Export-Import Bank funds available for similar projects throughout Poland.

  15. Test Control Center

    NASA Technical Reports Server (NTRS)

    2000-01-01

    At the test observation periscope in the Test Control Center exhibit in StenniSphere at the John C. Stennis Space Center in Hancock County, Miss., visitors can observe a test of a Space Shuttle Main Engine exactly as test engineers might see it during a real engine test. The Test Control Center exhibit exactly simulates not only the test control environment, but also the procedure of testing a rocket engine. Designed to entertain while educating, StenniSphere includes informative dispays and exhibits from NASA's lead center for rocket propulsion and remote sensing applications. StenniSphere is open free of charge from 9 a.m. to 5 p.m. daily.

  16. Autonomous Flying Controls Testbed

    NASA Technical Reports Server (NTRS)

    Motter, Mark A.

    2005-01-01

    The Flying Controls Testbed (FLiC) is a relatively small and inexpensive unmanned aerial vehicle developed specifically to test highly experimental flight control approaches. The most recent version of the FLiC is configured with 16 independent aileron segments, supports the implementation of C-coded experimental controllers, and is capable of fully autonomous flight from takeoff roll to landing, including flight test maneuvers. The test vehicle is basically a modified Army target drone, AN/FQM-117B, developed as part of a collaboration between the Aviation Applied Technology Directorate (AATD) at Fort Eustis,Virginia and NASA Langley Research Center. Several vehicles have been constructed and collectively have flown over 600 successful test flights.

  17. Vehicle speed control device

    SciTech Connect

    Thornton-Trump, W.E.

    1987-03-10

    An apparatus is described for automatically limiting the speed of a vehicle powered by an internal combustion engine having a spark ignition system with an ignition coil, comprising: sensor means for generating a speed signal directly representative of the speed of the vehicle comprising a series of speed signal pulses having a pulse repetition frequency proportional to the speed of the vehicle; control means for converting speed signal pulses into a DC voltage proportional to the vehicle speed; means for comparing the DC voltage to a predetermined DC voltage having substantially zero AC components representative of a predetermined maximum speed and for generating a difference signal in response thereto; and means for generating a pulse-width modulated control signal responsive to the difference signal; power means responsive to the control signal for intermittently interrupting the ignition system.

  18. [Environmental microbiological control].

    PubMed

    Martín Salas, Carmen; Tordoya Titichoca, Igberto J; Ezpeleta Baquedano, Carmen

    2016-07-01

    The environmental microbiological control is necessary to prevent infections associated with certain procedures that are performed at the hospital. In this review the procedures for control of water and dialysis fluids, and air in operating rooms and immunocompromised units are addressed. The dialysis quality management guidelines define the highest levels of chemical, microbiological and endotoxin in purified water and dialysis fluids based on the recommendations of scientific societies. The microbiological control of water and dialysis fluids should include detection of microorganisms and endotoxin levels. Regarding the microbiological air sampling of operating rooms and immunocompromised units the types of clean rooms in which is recommended to perform microbiological air monitoring; the sample collection methods; culture media; incubation conditions; the most common microorganisms, and permissible levels depending on the type of surgery are described.

  19. NUCLEAR REACTOR CONTROL SYSTEM

    DOEpatents

    Howard, D.F.; Motta, E.E.

    1961-06-27

    A method for controlling the excess reactivity in a nuclear reactor throughout the core life while maintaining the neutron flux distribution at the desired level is described. The control unit embodies a container having two electrodes of different surface area immersed in an electrolytic solution of a good neutron sbsorbing metal ion such as boron, gadolinium, or cadmium. Initially, the neutron absorber is plated on the larger electrode to control the greater neutron flux of a freshly refueled core. As the fuel burns up, the excess reactivity decreases and the neutron absorber is then plated onto the smaller electrode so that the number of neutrons absorbed also decreases. The excess reactivity in the core may thus be maintained without the introduction of serious perturbations in the neutron flux distributibn.

  20. Voltage controlled current source

    DOEpatents

    Casne, Gregory M.

    1992-01-01

    A seven decade, voltage controlled current source is described for use in testing intermediate range nuclear instruments that covers the entire test current range of from 10 picoamperes to 100 microamperes. High accuracy is obtained throughout the entire seven decades of output current with circuitry that includes a coordinated switching scheme responsive to the input signal from a hybrid computer to control the input voltage to an antilog amplifier, and to selectively connect a resistance to the antilog amplifier output to provide a continuous output current source as a function of a preset range of input voltage. An operator controlled switch provides current adjustment for operation in either a real-time simulation test mode or a time response test mode.

  1. Electric turbocompound control system

    DOEpatents

    Algrain, Marcelo C.

    2007-02-13

    Turbocompound systems can be used to affect engine operation using the energy in exhaust gas that is driving the available turbocharger. A first electrical device acts as a generator in response to turbocharger rotation. A second electrical device acts as a motor to put mechanical power into the engine, typically at the crankshaft. Apparatus, systems, steps, and methods are described to control the generator and motor operations to control the amount of power being recovered. This can control engine operation closer to desirable parameters for given engine-related operating conditions compared to actual. The electrical devices can also operate in "reverse," going between motor and generator functions. This permits the electrical device associated with the crankshaft to drive the electrical device associated with the turbocharger as a motor, overcoming deficient engine operating conditions such as associated with turbocharger lag.

  2. CEBAF Control Room Renovation

    SciTech Connect

    Michael Spata; Thomas Oren

    2005-05-01

    The Machine Control Center (MCC) at Jefferson Lab's Continuous Electron Beam Accelerator Facility (CEBAF) was initially constructed in the early 1990s and based on proven technology of that era. Through our experience over the last 15 years and in our planning for the facility's 12 GeV upgrade we reevaluated the control room environment to capitalize on emerging visualization and display technologies and improve workflow processes and ergonomic attributes. This effort also sets the foundation for the redevelopment of the accelerator's control system to deliver high reliability performance with improvements in beam specifications management and information flow. The complete renovation was performed over a three-week maintenance period with no interruption to beam operations. We present the results of this effort.

  3. CEBAF Control Room Renovation

    SciTech Connect

    Michael Spata; Thomas Oren

    2005-05-01

    The Machine Control Center at Jefferson Lab's Continuous Electron Beam Accelerator Facility was initially constructed in the early 1990s and based on proven technology of that era. Through our experience over the last 15 years and in our planning for the facilities 12 GeV upgrade we reevaluated the control room environment to capitalize on emerging visualization and display technologies and improve on workflow processes and ergonomic attributes. This effort also sets the foundation for the redevelopment of the accelerator's control system to deliver high reliability performance with improvements in beam specifications management and information flow. The complete renovation was performed over a three-week period with no interruption to beam operations. We present the results of this effort.

  4. Distributed environmental control

    NASA Technical Reports Server (NTRS)

    Cleveland, Gary A.

    1992-01-01

    We present an architecture of distributed, independent control agents designed to work with the Computer Aided System Engineering and Analysis (CASE/A) simulation tool. CASE/A simulates behavior of Environmental Control and Life Support Systems (ECLSS). We describe a lattice of agents capable of distributed sensing and overcoming certain sensor and effector failures. We address how the architecture can achieve the coordinating functions of a hierarchical command structure while maintaining the robustness and flexibility of independent agents. These agents work between the time steps of the CASE/A simulation tool to arrive at command decisions based on the state variables maintained by CASE/A. Control is evaluated according to both effectiveness (e.g., how well temperature was maintained) and resource utilization (the amount of power and materials used).

  5. Power Systems Control Architecture

    SciTech Connect

    James Davidson

    2005-01-01

    A diagram provided in the report depicts the complexity of the power systems control architecture used by the national power structure. It shows the structural hierarchy and the relationship of the each system to those other systems interconnected to it. Each of these levels provides a different focus for vulnerability testing and has its own weaknesses. In evaluating each level, of prime concern is what vulnerabilities exist that provide a path into the system, either to cause the system to malfunction or to take control of a field device. An additional vulnerability to consider is can the system be compromised in such a manner that the attacker can obtain critical information about the system and the portion of the national power structure that it controls.

  6. Pattern, Growth and Control

    PubMed Central

    Lander, Arthur D.

    2011-01-01

    The view of biology as goal-directed engineering has deep historical roots in developmental biology, a field currently benefitting from an influx of ideas and methods from systems biology. Systems biology draws on non-biological paradigms to explain developmental mechanisms of control, the specific type of regulation that achieves or maintains a desired end. This review highlights some of the current efforts designed to elucidate basic design principles underlying the engineering objectives of robustness, precision, and scaling that are required during developmental control of growth and pattern formation. Examples from vertebrate and invertebrate development are used to illustrate general principles including the value of integral feedback in achieving set-point control; the usefulness of self-organizing behavior; the importance of recognizing and appropriately handling noise; and the No Free Lunch theory. Through the examination of such principles, systems biology offers a functional framework to make sense of the mechanistic complexity of organismal development. PMID:21414486

  7. Timing control system

    NASA Technical Reports Server (NTRS)

    Wiker, Gordon A. (Inventor); Wells, Jr., George H. (Inventor)

    1989-01-01

    A timing control system is disclosed which is particularly useful in connection with simulated mortar shells. Special circuitry is provided to assure that the shell does not overshoot, but rather detonates early in case of an improper condition; this ensures that ground personnel will not be harmed by a delayed detonation. The system responds to an externally applied frequency control code which is configured to avoid any confusion between different control modes. A premature detonation routine is entered in case an improper time-setting signal is entered, or if the shell is launched before completion of the time-setting sequence. Special provisions are also made for very early launch situations and improper detonator connections. An alternate abort mode is provided to discharge the internal power supply without a detonation in a manner that can be externally monitored, thereby providing a mechanism for non-destructive testing. The abort mode also accelerates the timing function for rapid testing.

  8. Timing Control System

    NASA Technical Reports Server (NTRS)

    Wiker, Gordon A. (Inventor); Wells, George H., Jr. (Inventor)

    1987-01-01

    A timing control system is disclosed which is particularly useful in connection with simulated mortar shells. Special circuitry is provided to assure that the shell does not over shoot, but rather detonates early in case of an improper condition; this ensures that ground personnel will not be harmed by a delayed detonation. The system responds to an externally applied frequency control code which is configured to avoid any confusion between different control modes. A premature detonation routine is entered in case an improper time-setting signal is entered, or if the shell is launched before completion of the time-setting sequence. Special provisions are also made for very early launch situations and improper detonator connections. An alternate abort mode is provided to discharge the internal power supply without a detonation in a manner that can be externally monitored, thereby providing a mechanism for non-destructive testing. The abort mode also accelerates the timing function for rapid testing.

  9. REACTOR CONTROL DEVICE

    DOEpatents

    Graham, R.H.

    1962-09-01

    A wholly mechanical compact control device is designed for automatically rendering the core of a fission reactor subcritical in response to core temperatures in excess of the design operating temperature limit. The control device comprises an expansible bellows interposed between the base of a channel in a reactor core and the inner end of a fuel cylinder therein which is normally resiliently urged inwardly. The bellows contains a working fluid which undergoes a liquid to vapor phase change at a temperature substantially equal to the design temperature limit. Hence, the bellows abruptiy expands at this limiting temperature to force the fuel cylinder outward and render the core subcritical. The control device is particularly applicable to aircraft propulsion reactor service. (AEC)

  10. Remote Controlled Orbiter Capability

    NASA Technical Reports Server (NTRS)

    Garske, Michael; delaTorre, Rafael

    2007-01-01

    The Remote Control Orbiter (RCO) capability allows a Space Shuttle Orbiter to perform an unmanned re-entry and landing. This low-cost capability employs existing and newly added functions to perform key activities typically performed by flight crews and controllers during manned re-entries. During an RCO landing attempt, these functions are triggered by automation resident in the on-board computers or uplinked commands from flight controllers on the ground. In order to properly route certain commands to the appropriate hardware, an In-Flight Maintenance (IFM) cable was developed. Currently, the RCO capability is reserved for the scenario where a safe return of the crew from orbit may not be possible. The flight crew would remain in orbit and await a rescue mission. After the crew is rescued, the RCO capability would be used on the unmanned Orbiter in an attempt to salvage this national asset.

  11. Timing control system

    NASA Astrophysics Data System (ADS)

    Wiker, Gordon A.; Wells, George H., Jr.

    1987-09-01

    A timing control system is disclosed which is particularly useful in connection with simulated mortar shells. Special circuitry is provided to assure that the shell does not over shoot, but rather detonates early in case of an improper condition; this ensures that ground personnel will not be harmed by a delayed detonation. The system responds to an externally applied frequency control code which is configured to avoid any confusion between different control modes. A premature detonation routine is entered in case an improper time-setting signal is entered, or if the shell is launched before completion of the time-setting sequence. Special provisions are also made for very early launch situations and improper detonator connections. An alternate abort mode is provided to discharge the internal power supply without a detonation in a manner that can be externally monitored, thereby providing a mechanism for non-destructive testing. The abort mode also accelerates the timing function for rapid testing.

  12. Innovative Control Effectors (ICE)

    DTIC Science & Technology

    1996-01-01

    S0.06- 0.05 Max A/B 1. ..... C 0.04 201-TV Control Power Available t Mil Power It 0.03- 201 Control Power Available [= !,-===:CPR Max /VB 0.01. CPR Mil...3 ’" t ~~~vl 1 ’ N’ -1018 1-\\ 101-4 -0.05 -0.04 -0.03 -0.02 -0.01 0 0.01 0.02 Yaw Power Figure 6-12 All Five Control Suites Can Achieve Level 1...SPLI" T LEADING EDGE FLAP • fELEVON WEAPONS BAY j-PITCH FLAP VECTORING NOZZLE F-22 LEADING EDGE FLAP F-22 AILERON POWER DRIVE ACTUATOR F-22 FLAPERON

  13. Mercury control in 2009

    SciTech Connect

    Sjostrom, S.; Durham, M.; Bustard, J.; Martin, C.

    2009-07-15

    Although activated carbon injection (ACI) has been proven to be effective for many configurations and is a preferred option at many plants sufficient quantities of powdered activated coking (PAC) must be available to meet future needs. The authors estimate that upcoming federal and state regulations will result in tripling the annual US demand for activated carbon to nearly 1.5 billion lb from approximately 450 million lb. Rapid expansion of US production capacity is required. Many PAC manufacturers are discussing expansion of their existing production capabilities. One company, ADA Carbon Solutions, is in the process of constructing the largest activated carbon facility in North America to meet the future demand for PAC as a sorbent for mercury control. Emission control technology development and commercialization is driven by regulation and legislation. Although ACI will not achieve > 90% mercury control at every plant, the expected required MACT legislation level, it offers promise as a low-cost primary mercury control technology option for many configurations and an important trim technology for others. ACI has emerged as the clear mercury-specific control option of choice, representing over 98% of the commercial mercury control system orders to date. As state regulations are implemented and the potential for a federal rule becomes more imminent, suppliers are continuing to develop technologies to improve the cost effectiveness and limit the balance of plant impacts associated with ACI and are developing additional PAC production capabilities to ensure that the industry's needs are met. The commercialisation of ACI is a clear example of industry, through the dedication of many individuals and companies with support from the DOE and EPRI, meeting the challenge of developing cost-effectively reducing emissions from coal-fired power plants. 7 refs., 1 fig.

  14. Propulsion controlled aircraft computer

    NASA Technical Reports Server (NTRS)

    Cogan, Bruce R. (Inventor)

    2010-01-01

    A low-cost, easily retrofit Propulsion Controlled Aircraft (PCA) system for use on a wide range of commercial and military aircraft consists of an propulsion controlled aircraft computer that reads in aircraft data including aircraft state, pilot commands and other related data, calculates aircraft throttle position for a given maneuver commanded by the pilot, and then displays both current and calculated throttle position on a cockpit display to show the pilot where to move throttles to achieve the commanded maneuver, or is automatically sent digitally to command the engines directly.

  15. REACTOR CONTROL SYSTEM

    DOEpatents

    MacNeill, J.H.; Estabrook, J.Y.

    1960-05-10

    A reactor control system including a continuous tape passing through a first coolant passageway, over idler rollers, back through another parallel passageway, and over motor-driven rollers is described. Discrete portions of fuel or poison are carried on two opposed active sections of the tape. Driving the tape in forward or reverse directions causes both active sections to be simultaneously inserted or withdrawn uniformly, tending to maintain a more uniform flux within the reactor. The system is particularly useful in mobile reactors, where reduced inertial resistance to control rod movement is important.

  16. Instrument Attitude Precision Control

    NASA Technical Reports Server (NTRS)

    Juang, Jer-Nan

    2004-01-01

    A novel approach is presented in this paper to analyze attitude precision and control for an instrument gimbaled to a spacecraft subject to an internal disturbance caused by a moving component inside the instrument. Nonlinear differential equations of motion for some sample cases are derived and solved analytically to gain insight into the influence of the disturbance on the attitude pointing error. A simple control law is developed to eliminate the instrument pointing error caused by the internal disturbance. Several cases are presented to demonstrate and verify the concept presented in this paper.

  17. AUTOMATIC FREQUENCY CONTROL SYSTEM

    DOEpatents

    Hansen, C.F.; Salisbury, J.D.

    1961-01-10

    A control is described for automatically matching the frequency of a resonant cavity to that of a driving oscillator. The driving oscillator is disconnected from the cavity and a secondary oscillator is actuated in which the cavity is the frequency determining element. A low frequency is mixed with the output of the driving oscillator and the resultant lower and upper sidebands are separately derived. The frequencies of the sidebands are compared with the secondary oscillator frequency. deriving a servo control signal to adjust a tuning element in the cavity and matching the cavity frequency to that of the driving oscillator. The driving oscillator may then be connected to the cavity.

  18. A microprogrammable radar controller

    NASA Technical Reports Server (NTRS)

    Law, D. C.

    1986-01-01

    The Wave Propagation Lab. has completed the design and construction of a microprogrammable radar controller for atmospheric wind profiling. Unlike some radar controllers using state machines or hardwired logic for radar timing, this design is a high speed programmable sequencer with signal processing resources. A block diagram of the device is shown. The device is a single 8 1/2 inch by 10 1/2 inch printed circuit board and consists of three main subsections: (1) the host computer interface; (2) the microprogram sequencer; and (3) the signal processing circuitry. Each of these subsections are described in detail.

  19. NASA control research overview

    NASA Technical Reports Server (NTRS)

    Mciver, D. E.

    1984-01-01

    An overview of NASA research activities related to the control of aeronautical vehicles is presented. A groundwork is laid by showing the organization at NASA Headquarters for supporting programs and providing funding. Then a synopsis of many of the ongoing activities is presented, some of which will be presented in greater detail elsewhere. A major goal of the workshop is to provide a showcase of ongoing NASA sponsored research. Then, through the panel sessions and conversations with workshop participants, it is hoped to glean a focus for future directions in aircraft controls research.

  20. IWHS Elevator Controller Study.

    DTIC Science & Technology

    1978-11-24

    the SSR ’s the LED is used to indicate the excitation across the two input ter- minals. 7.3 STATIC LOGIC LOU This design approach uses DC / DC ...14 16-bit bidirectional shift register , 5111 DC $5 505 Malt i pl ao e r . D ig ital IA Ten 2-input digI ta l eult lp l e n er s . LPTTI . AP 56 (RN...controller was precipitated by the lack of spare parts for , and the poor maintenance of , the present controller. Design approaches based on relay

  1. Pipe Line Control

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The array of tanks, pipes and valves in the photo below is a petroleum tank farm in Georgia, part of a petrochemical pipe line system that moves refined petroleum products from Texas and Louisiana to the mid-Eastern seaboard. The same pipes handle a number of different products, such as gasoline, kerosene, jet fuel or fuel oil. The fluids are temporarily stored in tanks, pumped into the pipes in turn and routed to other way stations along the pipe line. The complex job of controlling, measuring and monitoring fuel flow is accomplished automatically by a computerized control and communications system which incorporates multiple space technologies.

  2. Tank depletion flow controller

    DOEpatents

    Georgeson, Melvin A.

    1976-10-26

    A flow control system includes two bubbler tubes installed at different levels within a tank containing such as radioactive liquid. As the tank is depleted, a differential pressure transmitter monitors pressure differences imparted by the two bubbler tubes at a remote, shielded location during uniform time intervals. At the end of each uniform interval, balance pots containing a dense liquid are valved together to equalize the pressures. The resulting sawtooth-shaped signal generated by the differential pressure transmitter is compared with a second sawtooth signal representing the desired flow rate during each time interval. Variations in the two signals are employed by a control instrument to regulate flow rate.

  3. Communicating Networked Control Systems

    DTIC Science & Technology

    2007-03-31

    Bahamas, pages 1010-1015. 64. Carmen Del Vecchio and I.C. Paschalidis, “Supply Contracts with Service Level Requirements”, Proceedings of the IFAC...control using Monte Carlo sensing,” Proc. IEEE International Conference on Robotics and Automation, pp. 3058-3063, 2005. 10. S.B. Andersson, A.A. Handzel, V...Analysis, Madrid Spain. 20. S. Andersson and D. Hristu-Varsakelis, “Language-based feedback control using Monte -Carlo sensing”, to be subm. To IEEE Int’l

  4. Blood Pressure Control

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Engineering Development Laboratory developed a system for the cardiovascular study of weightless astronauts. This was designed to aid people with congestive heart failure and diabetes. While in space, astronauts' blood pressure rises, heart rate becomes unstable, and there are sometimes postflight lightheadedness or blackouts. The Baro-Cuff studies the resetting of blood pressure. When a silicone rubber chamber is strapped to the neck, the Baro-Cuff stimulates the carotid arteries by electronically controlled pressure application. Blood pressure controls in patients may be studied.

  5. Power semiconductor controlled drives

    NASA Astrophysics Data System (ADS)

    Dubey, Gopal K.

    This book presents power semiconductor controlled drives employing dc motors, induction motors, and synchronous motors. The dynamics of motor and load systems are covered. Open-loop and closed-loop drives are considered, and thyristor, power transistor, and GTO converters are discussed. In-depth coverage is given to ac drives, particularly those fed by voltage and current source inverters and cycloconverters. Full coverage is given to brushless and commutatorless dc drives, including load-commuted synchronous motor drives. Rectifier-controlled dc drives are presented in detail.

  6. NEUTRONIC REACTOR CONTROL

    DOEpatents

    Metcalf, H.E.

    1958-10-14

    Methods of controlling reactors are presented. Specifically, a plurality of neutron absorber members are adjustably disposed in the reactor core at different distances from the center thereof. The absorber members extend into the core from opposite faces thereof and are operated by motive means coupled in a manner to simultaneously withdraw at least one of the absorber members while inserting one of the other absorber members. This feature effects fine control of the neutron reproduction ratio by varying the total volume of the reactor effective in developing the neutronic reaction.

  7. AUTOMATIC LIGHT CONTROL

    DOEpatents

    Artzt, M.

    1957-08-27

    A control system for a projection kinescope used in a facsimile scanning system and, in particular, meams for maintaining substantially constant the light emanating from the flying spot on the face of the kinescope are described. In general, the invention provides a feeler member disposed in such a position with respect to a projecting lens as to intercept a portion of the light striking the lens. Suitable circuitry in conjunction with a photomultiplier tube provides a signal proportional to the light intensity of the flying spot. The grid bias on the kinescope is controlled by this signal to maintain the intensity of the spot substantially constant.

  8. Pointing control for LDR

    NASA Technical Reports Server (NTRS)

    Yam, Y.; Briggs, C.

    1988-01-01

    One important aspect of the LDR control problem is the possible excitations of structural modes due to random disturbances, mirror chopping, and slewing maneuvers. An analysis was performed to yield a first order estimate of the effects of such dynamic excitations. The analysis involved a study of slewing jitters, chopping jitters, disturbance responses, and pointing errors, making use of a simplified planar LDR model which describes the LDR dynamics on a plane perpendicular to the primary reflector. Briefly, the results indicate that the command slewing profile plays an important role in minimizing the resultant jitter, even to a level acceptable without any control action. An optimal profile should therefore be studied.

  9. Towards cheaper control centers

    NASA Technical Reports Server (NTRS)

    Baize, Lionel

    1994-01-01

    Today, any approach to the design of new space systems must take into consideration an important constraint, namely costs. This approach is our guideline for new missions and also applies to the ground segment, and particularly to the control center. CNES has carried out a study on a recent control center for application satellites in order to take advantage of the experience gained. This analysis, the purpose of which is to determine, a posteriori, the costs of architecture needs and choices, takes hardware and software costs into account and makes a number of recommendations.

  10. DETAIL INTERIOR VIEW OF CONTROL PANEL IN CONTROL STATION, VIEW ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL INTERIOR VIEW OF CONTROL PANEL IN CONTROL STATION, VIEW TOWARDS WEST - St. Lucie Canal, Lock No. 1, Control Station, St. Lucie, Cross State Canal, Okeechobee Intracoastal Waterway, Stuart, Martin County, FL

  11. 17. DETAIL OF CONTROL PANEL FOR FILTER #9: CONTROL SWITCHES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. DETAIL OF CONTROL PANEL FOR FILTER #9: CONTROL SWITCHES CONTROL BY PERCENTAGE OF VALVE OPENINGS INFLUENT, EFFLUENT, DRAINAGE, BACKWASH AND SURFACE WASH. - F. E. Weymouth Filtration Plant, 700 North Moreno Avenue, La Verne, Los Angeles County, CA

  12. 3. VAL CONTROL STATION, VIEW OF CONTROL PANELS SHOWING MAIN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. VAL CONTROL STATION, VIEW OF CONTROL PANELS SHOWING MAIN PRESSURE GAUGES, LOOKING NORTH. - Variable Angle Launcher Complex, Control Station, CA State Highway 39 at Morris Reservior, Azusa, Los Angeles County, CA

  13. Robotic Manipulator Control Performance Evaluation.

    DTIC Science & Technology

    1986-08-01

    torque technique produces a control law analogous to the mathematically based exact linearization 1951, nonlinear feedback [201, and optimal control...law analogous to the mathematically based exact linearization [951, nonlinear feedback [201, and optimal control methods [651. Therefore the results...control law analogous to the mathematically based exact linearization [951, nonlinear feedback [201, and optimal control methods [65]. Knowledge about

  14. The CARMA Control System

    NASA Astrophysics Data System (ADS)

    Gwon, C.; Beard, A. D.; Daniel, P.; Hobbs, R.; Scott, S. L.; Kraybill, J. C.; Leitch, E.; Mehringer, D. M.; Plante, R.; Amarnath, N. S.; Pound, M. W.; Rauch, K. P.; Teuben, P. J.

    2004-07-01

    The Combined Array for Research in Millimeter-wave Astronomy (CARMA) will be the combination of the BIMA, OVRO, and SZA millimeter arrays. With first light scheduled for 2005, CARMA will be the first heterogeneous millimeter array, combining antennas varying from 3.5 m to 10.4 m in diameter. The controls for CARMA involve creating a uniform interface for all antennas. The antennas are grouped into five independently-controlled sub-arrays, which will be used for scientific observations, engineering, or maintenance. The sub-arrays are controlled by two components: the Sub-array Command Processor (SCP) and the Sub-array Tracker (SAT). While each sub-array has a dedicated SCP for handling command processing, a single SAT computes and distributes slowly varying parameters to the necessary sub-arrays. The sub-array interface uses CORBA distributed objects to physically separate the user interface from the array. This allows for stability in the core engine controlling the array while enabling flexibility in the user interface implementation.

  15. Active weld control

    NASA Technical Reports Server (NTRS)

    Powell, Bradley W.; Burroughs, Ivan A.

    1994-01-01

    Through the two phases of this contract, sensors for welding applications and parameter extraction algorithms have been developed. These sensors form the foundation of a weld control system which can provide action weld control through the monitoring of the weld pool and keyhole in a VPPA welding process. Systems of this type offer the potential of quality enhancement and cost reduction (minimization of rework on faulty welds) for high-integrity welding applications. Sensors for preweld and postweld inspection, weld pool monitoring, keyhole/weld wire entry monitoring, and seam tracking were developed. Algorithms for signal extraction were also developed and analyzed to determine their application to an adaptive weld control system. The following sections discuss findings for each of the three sensors developed under this contract: (1) weld profiling sensor; (2) weld pool sensor; and (3) stereo seam tracker/keyhole imaging sensor. Hardened versions of these sensors were designed and built under this contract. A control system, described later, was developed on a multiprocessing/multitasking operating system for maximum power and flexibility. Documentation for sensor mechanical and electrical design is also included as appendices in this report.

  16. Remotely controlled spray gun

    NASA Technical Reports Server (NTRS)

    Cunningham, William C. (Inventor)

    1987-01-01

    A remotely controlled spray gun is described in which a nozzle and orifice plate are held in precise axial alignment by an alignment member, which in turn is held in alignment with the general outlet of the spray gun by insert. By this arrangement, the precise repeatability of spray patterns is insured.

  17. Control Augmented Structural Synthesis

    NASA Technical Reports Server (NTRS)

    Lust, Robert V.; Schmit, Lucien A.

    1988-01-01

    A methodology for control augmented structural synthesis is proposed for a class of structures which can be modeled as an assemblage of frame and/or truss elements. It is assumed that both the plant (structure) and the active control system dynamics can be adequately represented with a linear model. The structural sizing variables, active control system feedback gains and nonstructural lumped masses are treated simultaneously as independent design variables. Design constraints are imposed on static and dynamic displacements, static stresses, actuator forces and natural frequencies to ensure acceptable system behavior. Multiple static and dynamic loading conditions are considered. Side constraints imposed on the design variables protect against the generation of unrealizable designs. While the proposed approach is fundamentally more general, here the methodology is developed and demonstrated for the case where: (1) the dynamic loading is harmonic and thus the steady state response is of primary interest; (2) direct output feedback is used for the control system model; and (3) the actuators and sensors are collocated.

  18. Commercializing Biological Control

    ERIC Educational Resources Information Center

    LeLeu, K. L.; Young, M. A.

    1973-01-01

    Describes the only commercial establishment involved in biological control in Australia. The wasp Aphitis melinus, which parasitizes the insect Red Scale, is bred in large numbers and released in the citrus groves where Red Scale is causing damage to the fruit. (JR)

  19. High Current Power Controller

    DTIC Science & Technology

    1981-04-01

    AFWAL-TR-81- 2016 U iui.N HIGH CURRENT Ŕ POWER CONTROLLER P. E. McCOLLUM Audwo ROCKWELL INTERNATIONAL AUTONETICS STRATEGIC SYSTEMS DIVISION 3370...personnel. During norm3l operation, HCP \\.s pose no hazard, bLt unde- certain operating conditions potential noaza-ds do exist. They are: (1) During

  20. Water Pollution Control Industry

    ERIC Educational Resources Information Center

    Environmental Science and Technology, 1974

    1974-01-01

    A special report on the state of the water pollution control industry reveals that due to forthcoming federal requirements, sales and the backlogs should increase; problems may ensue because of shortages of materials and inflation. Included are reports from various individual companies. (MLB)