Feasibility study of transmission of OTV camera control information in the video vertical blanking interval

NASA Technical Reports Server (NTRS)

White, Preston A., III

1994-01-01

The Operational Television system at Kennedy Space Center operates hundreds of video cameras, many remotely controllable, in support of the operations at the center. This study was undertaken to determine if commercial NABTS (North American Basic Teletext System) teletext transmission in the vertical blanking interval of the genlock signals distributed to the cameras could be used to send remote control commands to the cameras and the associated pan and tilt platforms. Wavelength division multiplexed fiberoptic links are being installed in the OTV system to obtain RS-250 short-haul quality. It was demonstrated that the NABTS transmission could be sent over the fiberoptic cable plant without excessive video quality degradation and that video cameras could be controlled using NABTS transmissions over multimode fiberoptic paths as long as 1.2 km.

Near-field visual acuity of pigeons: effects of head location and stimulus luminance.

PubMed

Hodos, W; Leibowitz, R W; Bonbright, J C

1976-03-01

Two pigeons were trained to discriminate a grating stimulus from a blank stimulus of equivalent luminance in a three-key chamber. The stimuli and blanks were presented behind a transparent center key. The procedure was a conditional discrimination in which pecks on the left key were reinforced if the blank had been present behind the center key and pecks on the right key were reinforced if the grating had been present behind the center key. The spatial frequency of the stimuli was varied in each session from four to 29.5 lines per millimeter in accordance with a variation of the method of constant stimuli. The number of lines per millimeter that the subjects could discriminate at threshold was determined from psychometric functions. Data were collected at five values of stimulus luminance ranging from--0.07 to 3.29 log cd/m2. The distance from the stimulus to the anterior nodal point of the eye, which was determined from measurements taken from high-speed motion-picture photographs of three additional pigeons and published intraocular measurements, was 62.0 mm. This distance and the grating detection thresholds were used to calculate the visual acuity of the birds at each level of luminance. Acuity improved with increasing luminance to a peak value of 0.52, which corresponds to a visual angle of 1.92 min, at a luminance of 2.33 log cd/m2. Further increase in luminance produced a small decline in acuity.

Hurricane Safety and Information - Central Pacific Hurricane Center -

Science.gov Websites

NOAA NWS United States Department of Commerce Central Pacific Hurricane Center National Oceanic and Distance Calculator Blank Tracking Maps ▾ Educational Resources Be Prepared! NWS Hurricane Prep Week Search For Go NWS All NOAA ▾ Hurricane Safety Hurricane Awareness Week Information from CPHC Red Cross

High-sensitivity x-ray mask damage studies employing holographic gratings and phase-shifting interferometry

NASA Astrophysics Data System (ADS)

Hansen, Matthew E.; Cerrina, Franco

1994-05-01

A high-sensitivity holographic and interferometric metrology developed at the Center for X- ray Lithography (CXrL) has been employed to investigate in-plane distortions (IPD) produced in x-ray mask materials. This metrology has been applied to characterize damage to x-ray mask materials exposed to synchrotron radiation. X-ray mask damage and accelerated mask damage studies on silicon nitride and silicon carbide were conducted on the Aladdin ES-1 and ES-2 beamline exposure stations, respectively. Accumulated in-plane distortions due to x-ray irradiation were extracted from the incremental interferometric phase maps to yield IPD vs. dose curves for silicon nitride mask blanks. Silicon carbide mask blanks were subjected to accelerated mask damage in the high flux 2 mm X 2 mm beam of the ES-2 exposure station. An accelerated damage study of silicon carbide has shown no in-plane distortion for an accumulated dose of 800 kJ/cm2 with a measurement sensitivity of less than 5 nm.

2. EAST ELEVATION OF POWER PLANT TEST STAND (HORIZONTAL TEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. EAST ELEVATION OF POWER PLANT TEST STAND (HORIZONTAL TEST STAND REMNANTS OF BUILDING-BLANK WHITE WALL ONLY ORIGINAL REMAINS. - Marshall Space Flight Center, East Test Area, Power Plant Test Stand, Huntsville, Madison County, AL

9. DETAIL OF INTERIOR OF FRONT PORCH SHOWING FRONT ENTRY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. DETAIL OF INTERIOR OF FRONT PORCH SHOWING FRONT ENTRY (LEFT) AND BLANK WALL (CENTER) CORRESPONDING TO LOCATION OF INTERIOR VAULTS. VIEW TO SOUTHEAST. - Boise Project, Boise Project Office, 214 Broadway, Boise, Ada County, ID

A gunner model for an AAA tracking task with interrupted observations

NASA Technical Reports Server (NTRS)

Yu, C. F.; Wei, K. C.; Vikmanis, M.

1982-01-01

The problem of modeling a trained human operator's tracking performance in an anti-aircraft system under various display blanking conditions is discussed. The input to the gunner is the observable tracking error subjected to repeated interruptions (blanking). A simple and effective gunner model was developed. The effect of blanking on the gunner's tracking performance is approached via modeling the observer and controller gains.

106-17 Telemetry Standards Front Matter

DTIC Science & Technology

2017-07-01

IS UNLIMITED ABERDEEN TEST CENTER DUGWAY PROVING GROUND REAGAN TEST SITE REDSTONE TEST CENTER WHITE SANDS MISSILE RANGE YUMA PROVING GROUND...Council US Army White Sands Missile Range, New Mexico 88002-5110 This page intentionally left blank. Telemetry Standards, IRIG Standard 106-17...TM receiver commands for interoperability. f. Task TG-141: Update IRIG 106 with Standards for Data Quality Metrics (DQM) and Data Quality

Metal flow of a tailor-welded blank in deep drawing process

NASA Astrophysics Data System (ADS)

Yan, Qi; Guo, Ruiquan

2005-01-01

Tailor welded blanks were used in the automotive industry to consolidate parts, reduce weight, and increase safety. In recent years, this technology was developing rapidly in China. In Chinese car models, tailor welded blanks had been applied in a lot of automobile parts such as rail, door inner, bumper, floor panel, etc. Concerns on the properties of tailor welded blanks had become more and more important for automobile industry. A lot of research had shown that the strength of the welded seam was higher than that of the base metal, such that the weld failure in the aspect of strength was not a critical issue. However, formability of tailor welded blanks in the stamping process was complex. Among them, the metal flow of tailor welded blanks in the stamping process must be investigated thoroughly in order to reduce the scrap rate during the stamping process in automobile factories. In this paper, the behavior of metal flow for tailor welded blanks made by the laser welding process with two types of different thickness combinations were studied in the deep drawing process. Simulations and experiment verification of the movement of weld line for tailor welded blanks were discussed in detail. Results showed that the control on the movement of welded seam during stamping process by taking some measures in the aspect of blank holder was effective.

Lithographic qualification of high-transmission mask blank for 10nm node and beyond

NASA Astrophysics Data System (ADS)

Xu, Yongan; Faure, Tom; Viswanathan, Ramya; Lobb, Granger; Wistrom, Richard; Burns, Sean; Hu, Lin; Graur, Ioana; Bleiman, Ben; Fischer, Dan; Mignot, Yann; Sakamoto, Yoshifumi; Toda, Yusuke; Bolton, John; Bailey, Todd; Felix, Nelson; Arnold, John; Colburn, Matthew

2016-04-01

In this paper, we discuss the lithographic qualification of high transmission (High T) mask for Via and contact hole applications in 10nm node and beyond. First, the simulated MEEF and depth of focus (DoF) data are compared between the 6% and High T attnPSM masks with the transmission of High T mask blank varying from 12% to 20%. The 12% High T blank shows significantly better MEEF and larger DoF than those of 6% attnPSM mask blank, which are consistent with our wafer data. However, the simulations show no obvious advantage in MEEF and DoF when the blank transmittance is larger than 12%. From our wafer data, it has been seen that the common process window from High T mask is 40nm bigger than that from the 6% attnPSM mask. In the elongated bar structure with smaller aspect ratio, 1.26, the 12% High T mask shows significantly less develop CD pull back in the major direction. Compared to the High T mask, the optimized new illumination condition for 6% attnPSM shows limited improvement in MEEF and the DoF through pitch. In addition, by using the High T mask blank, we have also investigated the SRAF printing, side lobe printing and the resist profile through cross sections, and no patterning risk has been found for manufacturing. As part of this work new 12% High T mask blank materials and processes were developed, and a brief overview of key mask technology development results have been shared. Overall, it is concluded that the High T mask, 12% transmission, provides the most robust and extendable lithographic solution for 10nm node and beyond.

Development of Methods and Equipment for Sheet Stamping

NASA Astrophysics Data System (ADS)

Botashev, A. Yu; Bisilov, N. U.; Malsugenov, R. S.

2018-03-01

New methods of sheet stamping were developed: the gas forming with double-sided heating of a blank part and the gas molding with backpressure. In case of the first method the blank part is heated to the set temperature by means of a double-sided impact of combustion products of gas mixtures, after which, under the influence of gas pressure a stamping process is performed. In case of gas molding with backpressure, the blank part is heated to the set temperature by one-sided impact of the combustion products, while backpressure is created on the opposite side of the blank part by compressed air. In both methods the deformation takes place in the temperature range of warm or hot treatment due to the heating of a blank part. This allows one to form parts of complicated shape within one technological operation, which significantly reduces the cost of production. To implement these methods, original devices were designed and produced, which are new types of forging and stamping equipment. Using these devices, an experimental research on the stamping process was carried out and high-quality parts were obtained, which makes it possible to recommend the developed methods of stamping in the industrial production. Their application in small-scale production will allow one to reduce the cost price of stamped parts 2 or 3 times.

Alternating phase-shift mask and binary mask for 45-nm node and beyond: the impact on the mask error control

NASA Astrophysics Data System (ADS)

Kojima, Yosuke; Shirasaki, Masanori; Chiba, Kazuaki; Tanaka, Tsuyoshi; Inazuki, Yukio; Yoshikawa, Hiroki; Okazaki, Satoshi; Iwase, Kazuya; Ishikawa, Kiichi; Ozawa, Ken

2007-05-01

For 45 nm node and beyond, the alternating phase-shift mask (alt. PSM), one of the most expected resolution enhancement technologies (RET) because of its high image contrast and small mask error enhancement factor (MEEF), and the binary mask (BIM) attract attention. Reducing CD and registration errors and defect are their critical issues. As the solution, the new blank for alt. PSM and BIM is developed. The top film of new blank is thin Cr, and the antireflection film and shielding film composed of MoSi are deposited under the Cr film. The mask CD performance is evaluated for through pitch, CD linearity, CD uniformity, global loading, resolution and pattern fidelity, and the blank performance is evaluated for optical density, reflectivity, sheet resistance, flatness and defect level. It is found that the performance of new blank is equal to or better than that of conventional blank in all items. The mask CD performance shows significant improvement. The lithography performance of new blank is confirmed by wafer printing and AIMS measurement. The full dry type alt. PSM has been used as test plate, and the test results show that new blank can almost meet the specifications of pi-0 CD difference, CD uniformity and process margin for 45 nm node. Additionally, the new blank shows the better pattern fidelity than that of conventional blank on wafer. AIMS results are almost same as wafer results except for the narrowest pattern. Considering the result above, this new blank can reduce the mask error factors of alt. PSM and BIM for 45 nm node and beyond.

A graphical method for determining the dry-depositional component of aerosol samples and their field blanks

NASA Astrophysics Data System (ADS)

Huang, Suilou; Rahn, Kenneth A.; Arimoto, Richard

During the Atmosphere/Ocean Chemistry Experiment (AEROCE), field blanks of certain elements in aerosol samples occasionally increased abruptly, always during periods of unusually high atmospheric concentrations. We hypothesized that the anomalous blanks were created by coarse aerosol entering the sampling shelters and depositing onto the blank filters. If so, samples taken nearby should have been similarly affected. To test this hypothesis, we developed a simple graphical method in which elemental masses in field blanks are plotted against elemental masses in pumped samples, and zones of proportionality between the two are sought. Data from Bermuda and Mace Head (coastal western Ireland) confirmed that depositional zones did indeed appear, but only for coarse-particle elements and only under certain conditions. Actual increases of crustal and pollution-derived elements agreed well with values predicted from settling velocities and sampling rates: blanks increased up to an order of magnitude or more but samples by less than 1%. Marine elements behaved like crustal elements in most samples but occasionally were much more enriched: blanks increased up to 30-fold and samples up to about 3%. It thus appears that when coarse-particle elements are present in high concentrations, their field blanks and samples may be measurably affected by dry deposition. Depending on the elements of interest, this dry deposition may have to be measured and the concentrations corrected.

Enabling high speed friction stir welding of aluminum tailor welded blanks

NASA Astrophysics Data System (ADS)

Hovanski, Yuri

Current welding technologies for production of aluminum tailor-welded blanks (TWBs) are utilized in low-volume and niche applications, and have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high-volumes. While friction stir welding (FSW) has traditionally been applied at linear velocities less than one meter per minute, high volume production applications demand the process be extended to higher velocities more amenable to cost sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low to moderate welding velocities do not directly translate to high speed linear friction stir welding. Therefore, in order to facilitate production of high volume aluminum FSW components, parameters were developed with a minimum welding velocity of three meters per minute. With an emphasis on weld quality, welded blanks were evaluated for post-weld formability using a combination of numerical and experimental methods. Evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum tailor-welded blanks, which provided validation of the numerical and experimental analysis of laboratory scale tests.

Attenuated phase-shift mask (PSM) blanks for flat panel display

NASA Astrophysics Data System (ADS)

Kageyama, Kagehiro; Mochizuki, Satoru; Yamakawa, Hiroyuki; Uchida, Shigeru

2015-10-01

The fine pattern exposure techniques are required for Flat Panel display applications as smart phone, tablet PC recently. The attenuated phase shift masks (PSM) are being used for ArF and KrF photomask lithography technique for high end pattern Semiconductor applications. We developed CrOx based large size PSM blanks that has good uniformity on optical characteristics for FPD applications. We report the basic optical characteristics and uniformity, stability data of large sized CrOx PSM blanks.

Quartz 9-inch size mask blanks for ArF PSM (Phase Shift Mask)

NASA Astrophysics Data System (ADS)

Harashima, Noriyuki; Isozaki, Tatsuya; Kawanishi, Arata; Kanai, Shuichiro; Kageyama, Kagehiro; Iso, Hiroyuki; Chishima, Tatsuya

2017-07-01

Semiconductor technology nodes are steadily miniaturizing. On the other hand, various efforts have been made to reduce costs, mass production lines have shifted from 200 mmφ of Si wafer to 300 mmφ, and technology development of Si wafer 450 mmφ is also in progress. As a photomask, 6-inch size binary Cr mask has been used for many years, but in recent years, the use of 9-inch binary Cr masks for Proximity Lithography Process in automotive applications, MEMS, packages, etc. has increased, and cost reduction has been taken. Since the miniaturization will progress in the above applications in the future, products corresponding to miniaturization are also desired in 9-inch photomasks. The high grade Cr - binary mask blanks used in proximity exposure process, there is a prospect of being able to use it by ULVAC COATING CORPORATION's tireless research. As further demands for miniaturization, KrF and ArF Lithography Process, which are used for steppers and scanners , there are also a demand for 9-inch size Mask Blanks. In ULVAC COATING CORPORATION, we developed a 9 - inch size KrF PSM mask Blanks prototype in 2016 and proposed a new high grade 9 - inch photomask. This time, we have further investigated and developed 9-inch size ArF PSM Mask Blanks corresponding to ArF Lithography Process, so we report it.

Positional priming of visual pop-out search is supported by multiple spatial reference frames

PubMed Central

Gokce, Ahu; Müller, Hermann J.; Geyer, Thomas

2015-01-01

The present study investigates the representations(s) underlying positional priming of visual ‘pop-out’ search (Maljkovic and Nakayama, 1996). Three search items (one target and two distractors) were presented at different locations, in invariant (Experiment 1) or random (Experiment 2) cross-trial sequences. By these manipulations it was possible to disentangle retinotopic, spatiotopic, and object-centered priming representations. Two forms of priming were tested: target location facilitation (i.e., faster reaction times – RTs– when the trial n target is presented at a trial n-1 target relative to n-1 blank location) and distractor location inhibition (i.e., slower RTs for n targets presented at n-1 distractor compared to n-1 blank locations). It was found that target locations were coded in positional short-term memory with reference to both spatiotopic and object-centered representations (Experiment 1 vs. 2). In contrast, distractor locations were maintained in an object-centered reference frame (Experiments 1 and 2). We put forward the idea that the uncertainty induced by the experiment manipulation (predictable versus random cross-trial item displacements) modulates the transition from object- to space-based representations in cross-trial memory for target positions. PMID:26136718

Methodology for cloud-based design of robots

NASA Astrophysics Data System (ADS)

Ogorodnikova, O. M.; Vaganov, K. A.; Putimtsev, I. D.

2017-09-01

This paper presents some important results for cloud-based designing a robot arm by a group of students. Methodology for the cloud-based design was developed and used to initiate interdisciplinary project about research and development of a specific manipulator. The whole project data files were hosted by Ural Federal University data center. The 3D (three-dimensional) model of the robot arm was created using Siemens PLM software (Product Lifecycle Management) and structured as a complex mechatronics product by means of Siemens Teamcenter thin client; all processes were performed in the clouds. The robot arm was designed in purpose to load blanks up to 1 kg into the work space of the milling machine for performing student's researches.

Development and Implementation of the Casting of Rods Made of Refractory Cast Alloys

NASA Astrophysics Data System (ADS)

Kabanov, I. V.; Urin, S. L.; Ivanyuk, A. S.; Nesterov, A. N.; Bogdanov, S. V.

2017-12-01

The problems of the production of a so-called casting rod blank made of a refractory casting alloy in the vacuum induction furnaces of AO Metallurgical Plant Electrostal are considered. A unique technology of casting and subsequent treatment of as-cast rod blanks made of refractory alloys is developed, tested, and optimized. As a result of the developed and performed measures for the production of metal products in the Consarc furnace, the ingot-to-product yield increases by 15% as compared to metal casting in an ISV-1.0 furnace. As a result, we have widened the range of cast alloy grades and are going to cast metals for the manufacture of blanks of other sizes and ranges of alloy an steel grades.

SEMATECH produces defect-free EUV mask blanks: defect yield and immediate challenges

NASA Astrophysics Data System (ADS)

Antohe, Alin O.; Balachandran, Dave; He, Long; Kearney, Patrick; Karumuri, Anil; Goodwin, Frank; Cummings, Kevin

2015-03-01

Availability of defect-free reflective mask has been one of the most critical challenges to extreme ultraviolet lithography (EUVL). To mitigate the risk, significant progress has been made on defect detection, pattern shifting, and defect repair. Clearly such mitigation strategies are based on the assumption that defect counts and sizes from incoming mask blanks must be below practical levels depending on mask specifics. The leading industry consensus for early mask product development is that there should be no defects greater than 80 nm in the quality area, 132 mm x 132 mm. In addition less than 10 defects smaller than 80 nm may be mitigable. SEMATECH has been focused on EUV mask blank defect reduction using Veeco Nexus TM IBD platform, the industry standard for mask blank production, and assessing if IBD technology can be evolved to a manufacturing solution. SEMATECH has recently announced a breakthrough reduction of defects in the mask blank deposition process resulting in the production of two defect-free EUV mask blanks at 54 nm inspection sensitivity (SiO2 equivalent). This paper will discuss the dramatic reduction of baseline EUV mask blank defects, review the current deposition process run and compare results with previous process runs. Likely causes of remaining defects will be discussed based on analyses as characterized by their compositions and whether defects are embedded in the multilayer stack or non-embedded.

Development and Piloting of the Prosocial Attitude Blank.

ERIC Educational Resources Information Center

Wasson, Rebecca; And Others

The Prosocial Attitude Blank (PAB) was designed to assess interpersonal values and ethical awareness of elementary school children. PAB was administered to 405 elementary students as one component of the evaluation of an intervention program designed to reduce interpersonal conflicts, increase literacy skills, and enhance children's ethical…

WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF PENNY BLANKS AND ZINC PRODUCTS

EPA Science Inventory

The U.S. EnvIronmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. aste Minimization Assessment Centers (WMACs) were established at selected u...

Effects of Moral Conduct Waivers on First-Term Attrition of U.S. Army Soldiers

DTIC Science & Technology

2008-03-01

Stephen L. Mehay Co-Advisor Robert N. Beck Dean, Graduate School of Business and Public Policy iv THIS PAGE INTENTIONALLY LEFT BLANK v...GUARD RECRUITING CENTER. Other Waiver BAA DEPENDENCY OF A MILITARY SPOUSE WAIVER GRANTED BY THE HIGHEST AUTHORITY LEVEL. Other Waiver BAB

High-speed blanking of copper alloy sheets: Material modeling and simulation

NASA Astrophysics Data System (ADS)

Husson, Ch.; Ahzi, S.; Daridon, L.

2006-08-01

To optimize the blanking process of thin copper sheets ( ≈ 1. mm thickness), it is necessary to study the influence of the process parameters such as the punch-die clearance and the wear of the punch and the die. For high stroke rates, the strain rate developed in the work-piece can be very high. Therefore, the material modeling must include the dynamic effects.For the modeling part, we propose an elastic-viscoplastic material model combined with a non-linear isotropic damage evolution law based on the theory of the continuum damage mechanics. Our proposed modeling is valid for a wide range of strain rates and temperatures. Finite Element simulations, using the commercial code ABAQUS/Explicit, of the blanking process are then conducted and the results are compared to the experimental investigations. The predicted cut edge of the blanked part and the punch-force displacement curves are discussed as function of the process parameters. The evolution of the shape errors (roll-over depth, fracture depth, shearing depth, and burr formation) as function of the punch-die clearance, the punch and the die wear, and the contact punch/die/blank-holder are presented. A discussion on the different stages of the blanking process as function of the processing parameters is given. The predicted results of the blanking dependence on strain-rate and temperature using our modeling are presented (for the plasticity and damage). The comparison our model results with the experimental ones shows a good agreement.

Stiffness management of sheet metal parts using laser metal deposition

NASA Astrophysics Data System (ADS)

Bambach, Markus; Sviridov, Alexander; Weisheit, Andreas

2017-10-01

Tailored blanks are established solutions for the production of load-adapted sheet metal components. In the course of the individualization of production, such semi-finished products are gaining importance. In addition to tailored welded blanks and tailored rolled blanks, patchwork blanks have been developed which allow a local increase in sheet thickness by welding, gluing or soldering patches onto sheet metal blanks. Patchwork blanks, however, have several limitations, on the one hand, the limited freedom of design in the production of patchwork blanks and, on the other hand, the fact that there is no optimum material bonding with the substrate. The increasing production of derivative and special vehicles on the basis of standard vehicles, prototype production and the functionalization of components require solutions with which semi-finished products and sheet metal components can be provided flexibly with local thickenings or functional elements with a firm metallurgical bond to the substrate. An alternative to tailored and patchwork blanks is, therefore, a free-form reinforcement applied by additive manufacturing via laser metal deposition (LMD). By combining metal forming and additive manufacturing, stiffness can be adapted to the loads based on standard components in a material-efficient manner and without the need to redesign the forming tools. This paper details a study of the potential of stiffness management by LMD using a demonstrator part. Sizing optimization is performed and part distortion is taken into account to find an optimal design for the cladding. A maximum stiffness increase of 167% is feasible with only 4.7% additional mass. Avoiding part distortion leads to a pareto-optimal design which achieves 95% more stiffness with 6% added mass.

Development of EUV mask handling technology at MIRAI-Selete

NASA Astrophysics Data System (ADS)

Ota, Kazuya; Amemiya, Mitsuaki; Taguchi, Takao; Kamono, Takashi; Kubo, Hiroyoshi; Takikawa, Tadahiko; Usui, Yoichi; Suga, Osamu

2007-03-01

We, MIRAI-Selete, started a new EUV mask program in April, 2006. Development of EUV mask handling technology is one of the key areas of the program. We plan to develop mask handling technology and to evaluate EUV mask carriers using Lasertec M3350, a particle inspection tool with the defect sensitivity less than 50nm PSL, and Mask Protection Engineering Tool (named "MPE Tool"). M3350 is a newly developed tool based on a conventional M1350 for EUV blanks inspection. Since our M3350 has a blank flipping mechanism in it, we can inspect the front and the back surface of the blank automatically. We plan to use the M3350 for evaluating particle adders during mask shipping, storage and handling. MPE Tool is a special tool exclusively developed for demonstration of pellicleless mask handling. It can handle a mask within a protective enclosure, which Canon and Nikon have been jointly proposing1, and also, can be modified to handle other type of carrier as the need arises.

Remediation of TNT and RDX in Groundwater Using Zero-Valent Iron Permeable Reactive Barriers

DTIC Science & Technology

2008-04-01

3 3.0 TECHNOLOGY DESCRIPTION ...................................................................................... 5 3.1... hydroxide NAVFAC-ESC Naval Facilities Engineering Service Center O&M operation and maintenance OHSU Oregon Health and Science University OD...remediation costs that may jeopardize major DoD programs and initiatives. 3 This page left blank intentionally. 3.0 TECHNOLOGY DESCRIPTION

FSW of Aluminum Tailor Welded Blanks across Machine Platforms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanski, Yuri; Upadhyay, Piyush; Carlson, Blair

2015-02-16

Development and characterization of friction stir welded aluminum tailor welded blanks was successfully carried out on three separate machine platforms. Each was a commercially available, gantry style, multi-axis machine designed specifically for friction stir welding. Weld parameters were developed to support high volume production of dissimilar thickness aluminum tailor welded blanks at speeds of 3 m/min and greater. Parameters originally developed on an ultra-high stiffness servo driven machine where first transferred to a high stiffness servo-hydraulic friction stir welding machine, and subsequently transferred to a purpose built machine designed to accommodate thin sheet aluminum welding. The inherent beam stiffness, bearingmore » compliance, and control system for each machine were distinctly unique, which posed specific challenges in transferring welding parameters across machine platforms. This work documents the challenges imposed by successfully transferring weld parameters from machine to machine, produced from different manufacturers and with unique control systems and interfaces.« less

Hardwood Blanks Expand Export Opportunities

Treesearch

Bruce G. Hansen; Philip A. Araman

1985-01-01

This article reviews the latest statistics pertaining to the export of hardwood lumber to the Pacific Rim; discusses possible reasons for the emergence and growth of this market; offers alternatives to rough hardwood lumber (two forms of value-added, hardwood blanks); and develops estimates of prices needed at the mill to earn a 30% return on investment from the...

ZERODUR thermo-mechanical modelling and advanced dilatometry for the ELT generation

NASA Astrophysics Data System (ADS)

Jedamzik, Ralf; Kunisch, Clemens; Westerhoff, Thomas

2016-07-01

Large amounts of low thermal expansion material are required for the upcoming ELT projects. The main mirror is designed using several hundreds of hexagonal 1.4 m sized mirror blanks. The M2 and M3 are monolithic 4 m class mirror blanks. The mirror blank material needs to fulfill tight requirements regarding CTE specification and homogeneity. Additionally the mirror blanks need to be dimensionally stable for more than 30 years. In particular, stress effects due to the changes in the environment shall not entail shape variation of more than 0.5 μm PV within 30 years. In 2010 SCHOTT developed a physically based model to describe the thermal and mechanical long time behavior of ZERODUR. The model enables simulation of the long time behavior of ZERODUR mirror blanks under realistic mechanical and thermal constraints. This presentation shows FEM simulation results on the long time behavior of the ELT M1, M2 and M3 mirror blanks under different loading conditions. Additionally the model results will be compared to an already 15 years lasting long time measurement of a ZERODUR sample at the German federal physical standardization institute (PTB). In recent years SCHOTT pushed the push rod dilatometer measurement technology to its limit. With the new Advanced Dilatometer CTE measurement accuracies of +- 3 ppb/K and reproducibilities of better 1 ppb/K have been achieved. The new Advanced Dilatometer exhibits excellent long time stability.

Spectral Studies of Solid Propellant Combustion. 3. Emission and Absorption Results for HMX2 Propellant

DTIC Science & Technology

1991-05-01

funding from the Anry Productivity Capital Investment Program. vii INTENTioNALLY LEFT BL~ANK viH I. INTRODUCTION During the last several years we...G-23 Dahlgren, VA 22448-5000 1 OSD/SDIO/ IST ATTN: L. Caveny 2 Commander Pentagon Naval Surface Warfare Center Washington, DC 20301-7100 ATTN: R

Analysis of the Oklahoma City Air Logistics Center’s (ALC) Contract Management Processes

DTIC Science & Technology

2007-12-01

be applied at all levels of business to include projects, divisions, and even an organization. The model scores organizations according to five... BUSINESS ADMINISTRATION from the NAVAL POSTGRADUATE SCHOOL December 2007 Authors: _____________________________________ Andrew E. Nordin...Dean Graduate School of Business and Public Policy iv THIS PAGE INTENTIONALLY LEFT BLANK v ABSTRACT

High-Speed Friction-Stir Welding To Enable Aluminum Tailor-Welded Blanks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanski, Yuri; Upadhyay, Piyush; Carsley, John

Current joining technologies for automotive aluminum alloys are utilized in low-volume and niche applications, and have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high-volumes. While friction stir welding has been traditionally applied at linear velocities less than one meter per minute, high volume production applications demand the process be extended to higher velocities more amenable to cost sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low to moderate welding velocities do not directly translatemore » to high speed linear friction stir welding. Therefore, in order to facilitate production of high volume aluminum welded components, parameters were developed with a minimum welding velocity of three meters per minute. With an emphasis on weld quality, welded blanks were evaluated for post-weld formability utilizing a combination of numerical and experimental methods. Evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum tailor-welded blanks, which provided validation of the numerical and experimental analysis of laboratory scale tests.« less

High-Speed Friction-Stir Welding to Enable Aluminum Tailor-Welded Blanks

NASA Astrophysics Data System (ADS)

Hovanski, Yuri; Upadhyay, Piyush; Carsley, John; Luzanski, Tom; Carlson, Blair; Eisenmenger, Mark; Soulami, Ayoub; Marshall, Dustin; Landino, Brandon; Hartfield-Wunsch, Susan

2015-05-01

Current welding technologies for production of aluminum tailor-welded blanks (TWBs) are utilized in low-volume and niche applications, and they have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high volumes. While friction-stir welding (FSW) has been traditionally applied at linear velocities less than 1 m/min, high-volume production applications demand the process be extended to higher velocities more amenable to cost-sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low-to-moderate welding velocities do not directly translate to high-speed linear FSW. Therefore, to facilitate production of high-volume aluminum FSW components, parameters were developed with a minimum welding velocity of 3 m/min. With an emphasis on weld quality, welded blanks were evaluated for postweld formability using a combination of numerical and experimental methods. An evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum TWBs, which provided validation of the numerical and experimental analysis of laboratory-scale tests.

NHEXAS PHASE I ARIZONA STUDY--QA ANALYTICAL RESULTS FOR PESTICIDE METABOLITES IN BLANK SAMPLES

EPA Science Inventory

The Pesticide Metabolites in Blank Samples data set contains the analytical results of measurements of up to 4 pesticide metabolites in 3 blank samples from 3 households. Measurements were made in blank samples of urine. Blank samples were used to assess the potential for sampl...

NHEXAS PHASE I MARYLAND STUDY--QA ANALYTICAL RESULTS FOR METALS IN BLANKS

EPA Science Inventory

The Metals in Blanks data set contains the analytical results of measurements of up to 11 metals in 115 blank samples from 58 households. Measurements were made in blank samples of indoor and outdoor air, drinking water, beverages, urine, and blood. Blank samples were used to a...

NHEXAS PHASE I MARYLAND STUDY--QA ANALYTICAL RESULTS FOR PESTICIDES IN BLANKS

EPA Science Inventory

The Pesticides in Blanks data set contains the analytical results of measurements of up to 20 pesticides in 70 blank samples from 46 households. Measurements were made in blank samples of indoor air, dust, soil, drinking water, food, beverages, and blood serum. Blank samples we...

NHEXAS PHASE I MARYLAND STUDY--QA ANALYTICAL RESULTS FOR PESTICIDE METABOLITES IN BLANKS

EPA Science Inventory

The Pesticide Metabolites in Blanks data set contains the analytical results of measurements of up to 4 pesticide metabolites in 14 blank samples from 13 households. Measurements were made in blank samples of urine. Blank samples were used to assess the potential for sample con...

EUV mask defect inspection and defect review strategies for EUV pilot line and high volume manufacturing

NASA Astrophysics Data System (ADS)

Chan, Y. David; Rastegar, Abbas; Yun, Henry; Putna, E. Steve; Wurm, Stefan

2010-04-01

Reducing mask blank and patterned mask defects is the number one challenge for extreme ultraviolet lithography. If the industry succeeds in reducing mask blank defects at the required rate of 10X every year for the next 2-3 years to meet high volume manufacturing defect requirements, new inspection and review tool capabilities will soon be needed to support this goal. This paper outlines the defect inspection and review tool technical requirements and suggests development plans to achieve pilot line readiness in 2011/12 and high volume manufacturing readiness in 2013. The technical specifications, tooling scenarios, and development plans were produced by a SEMATECH-led technical working group with broad industry participation from material suppliers, tool suppliers, mask houses, integrated device manufacturers, and consortia. The paper summarizes this technical working group's assessment of existing blank and mask inspection/review infrastructure capabilities to support pilot line introduction and outlines infrastructure development requirements and tooling strategies to support high volume manufacturing.

Information model construction of MES oriented to mechanical blanking workshop

NASA Astrophysics Data System (ADS)

Wang, Jin-bo; Wang, Jin-ye; Yue, Yan-fang; Yao, Xue-min

2016-11-01

Manufacturing Execution System (MES) is one of the crucial technologies to implement informatization management in manufacturing enterprises, and the construction of its information model is the base of MES database development. Basis on the analysis of the manufacturing process information in mechanical blanking workshop and the information requirement of MES every function module, the IDEF1X method was adopted to construct the information model of MES oriented to mechanical blanking workshop, and a detailed description of the data structure feature included in MES every function module and their logical relationship was given from the point of view of information relationship, which laid the foundation for the design of MES database.

NHEXAS PHASE I REGION 5 STUDY--QA ANALYTICAL RESULTS FOR METALS IN BLANKS

EPA Science Inventory

This data set includes analytical results for measurements of metals in 205 blank samples and for particles in 64 blank samples. Measurements were made for up to 12 metals in blank samples of air, dust, soil, water, food and beverages, blood, hair, and urine. Blank samples were u...

Benchmarking Best Practices in Transformation for Sea Enterprise

DTIC Science & Technology

2006-09-15

programs. The following are some current trends. Less management and more employee empowerment: In 1988, Peter Drucker predicted that in twenty...Acting President Provost The Center for Defense Management Reform, Graduate School of Business & Public Policy, Naval Postgraduate School...and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record No. 806 (U.S. Geological Survey, TMGS Magnetometer/Towed Array)

DTIC Science & Technology

2007-05-01

BOX 25046, FEDERAL CENTER, M.S. 964 DENVER, CO 80225-0046 TECHNOLOGY TYPE/PLATFORM: TMGS MAGNETOMETER/TOWED ARRAY PREPARED BY: U.S. ARMY...GEOLOGICAL SURVEY, TMGS MAGNETOMETER/TOWED ARRAY) 8-CO-160-UXO-021 Karwatka, Michael... TMGS Magnetometer/Towed Array, MEC Unclassified Unclassified Unclassified SAR (Page ii Blank) i ACKNOWLEDGMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wold, Isak G. B.; Barger, Amy J.; Owen, Frazer N.

We present 1.4 GHz catalogs for the cluster fields A370 and A2390 observed with the Very Large Array. These are two of the deepest radio images of cluster fields ever taken. The A370 image covers an area of 40' Multiplication-Sign 40' with a synthesized beam of {approx}1.''7 and a noise level of {approx}5.7 {mu}Jy near the field center. The A2390 image covers an area of 34' Multiplication-Sign 34' with a synthesized beam of {approx}1.''4 and a noise level of {approx}5.6 {mu}Jy near the field center. We catalog 200 redshifts for the A370 field. We construct differential number counts for themore » central regions (radius < 16') of both clusters. We find that the faint (S{sub 1.4{sub GHz}} < 3 mJy) counts of A370 are roughly consistent with the highest blank field number counts, while the faint number counts of A2390 are roughly consistent with the lowest blank field number counts. Our analyses indicate that the number counts are primarily from field radio galaxies. We suggest that the disagreement of our number counts can be largely attributed to cosmic variance.« less

Fill in the Blank: Culture Jamming and the Advertising of Agency

ERIC Educational Resources Information Center

Lambert-Beatty, Carrie

2010-01-01

This article is a review on billboard liberation and some other projects that develop the idea of talking back or over advertising in a playful and youthful way. In one of them, Ji Lee's Bubble Project, an artist places blank thought-bubble stickers on street advertisements and waits to see what people write on them, completing the work of art and…

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--QA ANALYTICAL RESULTS FOR METALS IN BLANK SAMPLES

EPA Science Inventory

The Metals in Blank Samples data set contains the analytical results of measurements of up to 27 metals in 52 blank samples. Measurements were made in blank samples of dust, indoor air, food, water, and dermal wipe residue. Blank samples were used to assess the potential for sa...

Influence of prepreg characteristics on stamp consolidation

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

2017-10-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The development of automated lay-up technologies further extends the applicability of stamp forming by allowing rapid lay-up of tailored blanks and partial preconsolidation. This partial preconsolidation makes the influence of prepreg more critical compared to conventional preconsolidation methods which provide full preconsolidation. This paper aims to highlight consolidation challenges that can appear when stamp forming blanks manufactured by automated lay-up. Important prepreg characteristics were identified based on an experimental study where a comparison was made between various prepreg in their as-received, deconsolidated and stamp consolidated state. It was found that adding up small thickness variations across the width of a prepreg when stacking plies into a blank by automated lay-up can cause non-uniform consolidation. Additionally, deconsolidation of the prepreg does not seem to obstruct interlaminar bonding, while intralaminar voids initially present in a prepreg cannot be removed during stamp forming. An additional preconsolidation step after automated lay-up seems necessary to remove blank thickness variations and intralaminar voids for the current prepregs. Eliminating this process step and the successful combination of rapid automated lay-up and stamp forming requires prepregs which are void-free and have less thickness variation.

Unmanned Tactical Autonomous Control and Collaboration Measures of Performance and Measures of Effectiveness

DTIC Science & Technology

2016-09-01

September 2016 Thesis Advisor: Dan Boger Co-Advisor: Scot Miller THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved... Scot Miller Co-Advisor Dan Boger Chair, Information Sciences Department iv THIS PAGE INTENTIONALLY LEFT BLANK v ABSTRACT As the technological...The authors would like to thank their advisors, Scot Miller and Dr. Dan Boger, for their incredibly helpful guidance and feedback on the development

Standard-Size Blanks for Furniture and Cabinets

Treesearch

Philip A. Araman

1983-01-01

Blanks are rough-dimension parts of a specific size which may be solid or glued up; quality depends on the final use of the material. Standard-size blanks are blanks made to standard thicknesses, lengths, and widths for each desired quality. Blanks in a few standard sizes can be used to make the thousands of different size rough-dimension parts needed by a furniture or...

Fill in the blank: culture jamming and the advertising of agency.

PubMed

Lambert-Beatty, Carrie

2010-01-01

This article is a review on billboard liberation and some other proj-ects that develop the idea of talking back or over advertising in a playful and youthful way. In one of them, Ji Lee's Bubble Project, an artist places blank thought-bubble stickers on street advertisements and waits to see what people write on them, completing the work of art and transgression. In other initiative, blank pages with the word God were placed around the city in place of advertising, inviting people to complete the prayer/complaint and to participate in a Suggestion Box, a project that collected "suggestions" from people out in the street. A review of playful and youthful ways to "rebel" against the impositions of powers like media and advertising.

Synthesis and Characterization of DNase 1-Stabilized Gold Nanoclusters

DTIC Science & Technology

2014-10-01

Acknowledgments The authors would like to thank Victor Rodriguez Santiago for the X-ray photoelectron spectroscopy. We also acknowledge the support of the...a Materials Research Science and Engineering Center Shared Experimental Facility. The authors would also like to thank Michael Sellers and Joshua...Postdoctoral Associateship. vi INTENTIONALLY LEFT BLANK. 1 1. Introduction The labeling of biological molecules like protein or DNA has been a large

preparation of microgram samples on iron wool for radiocarbon analysis via accelerator mass spectrometry: A closed-system approach

NASA Astrophysics Data System (ADS)

Verkouteren, R. Michael; Klouda, George A.; Currie, Lloyd A.; Donahue, Douglas J.; Jull, A. J. Timothy; Linick, T. W.

1987-11-01

A technique has been developed at NBS for the production of high quality targets for radiocarbon analysis by accelerator mass spectrometry (AMS). Our process optimizes chemical yields, ion currents and characterizes the chemical blank. The approach encompasses sample combustion to CO 2, catalytic reduction of CO 2 by Zn to CO, reduction to graphitic carbon on high-purity iron wool and in situ formation of a homogeneous iron-carbon bead; all steps are performed in a closed system. The total measurement system blank and variability are considered in the light of contributions from combustion, iron wool, reduction, bead formation and instrument blank. Additionally, use of this approach provides an increase in throughput, i.e. the effective management of large numbers of samples. Chemical yields for 50-800 μg C samples deposited on 15 mg iron wool were greater than 90%. Integrated 12C - ion currents observed were significant, being 4-64% of those observed in pure graphite. These currents are about an order of magnitude greater than those expected from dilution of graphite with an inert substrate. Isotopic accuracy, precision and blank were assessed by measuring the {14C }/{13C } ratios of a series of targets prepared from dead carbon and oxalic acid (SRM 4990C). Each target was typically measured for one hour; bead consumption was estimated at 5% to 10%. System blank subsequent to combustion was equivalent to (2.2 ± 0.5) μg modern carbon (chemistry + instrument); combustion blank currently stands at (0.4 ± 0.1) (SE, n = 6) μg C.

ZERODUR 4-m blank surviving up to 20 g acceleration

NASA Astrophysics Data System (ADS)

Westerhoff, Thomas; Werner, Thomas; Gehindy, Thorsten

2017-09-01

The glass ceramic ZERODUR developed as astronomical telescope mirror substrate material has been widely used in many telescopes due to its excellent small coefficient of thermal expansion. Many large and medium sized mirror substrate blanks have been delivered in the almost 50 years of ZERODUR business so far. Packaging and transportation of mirror substrates of 4 to 8 m in diameter with a weight between 3 and 20 tons requires special attention and sophisticated skills to successful deliver the blanks to their destination at polishing shops all over the world. Typically, a combination of road and sea transport needs to be organized. The requirements on the transport container are depending on the transport route and may vary from destination to destination. In any case the container needs to be able to sufficiently support the multi ton ZERODUR blank to avoid breaking under gravity. Additionally, the configuration needs to be able to absorb shocks happening during transport and loading between truck trailer and ship. For insurance reasons the transport container is always equipped with a GPS trackable shock recorder allowing to download the recorded accelerations on the container and the blank throughout the entire journey. This paper reports on the event of a 4 m class ZERODUR blank exposed to shocks up to 20 g during transport. The event will be discussed in detail together with lessons learned to avoid such events for future transports. Additionally, the 20 g acceleration will be discussed in respect to the data on bending strength for ZERODUR ground surfaces reported in numerous papers by Peter Hartmann et.al. in the last couple of years.

The Volumetric Imaging System for the Ionosphere (VISION)

DTIC Science & Technology

2011-01-01

telescope mirror is an 80 mm focal length, 50 mm diameter, first surface mirror with magnesium fluoride over aluminum coating on a zerodur blank...will be either a wedge–and–strip anode or a codacon. The telescope mirror is an 80 mm focal length, 2.5 cm diameter, first surface mirror with...magnesium fluoride over aluminum coating on a zerodur blank. The filters are the three reflection bandpass filters developed for and flown on

Evaluation of volatile organic compound (VOC) blank data and application of study reporting levels to groundwater data collected for the California GAMA Priority Basin Project, May 2004 through September 2010

USGS Publications Warehouse

Fram, Miranda S.; Olsen, Lisa D.; Belitz, Kenneth

2012-01-01

Volatile organic compounds (VOCs) were analyzed in quality-control samples collected for the California Groundwater Ambient Monitoring and Assessment (GAMA) Program Priority Basin Project. From May 2004 through September 2010, a total of 2,026 groundwater samples, 211 field blanks, and 109 source-solution blanks were collected and analyzed for concentrations of 85 VOCs. Results from analyses of these field and source-solution blanks and of 2,411 laboratory instrument blanks during the same time period were used to assess the quality of data for the 2,026 groundwater samples. Eighteen VOCs were detected in field blanks or source-solution blanks: acetone, benzene, bromodichloromethane, 2-butanone, carbon disulfide, chloroform, 1,1-dichloroethene, dichloromethane, ethylbenzene, tetrachloroethene, styrene, tetrahydrofuran, toluene, trichloroethene, trichlorofluoromethane, 1,2,4-trimethylbenzene, m- and p-xylenes, and o-xylene. The objective of the evaluation of the VOC-blank data was to determine if study reporting levels (SRLs) were needed for any of the VOCs detected in blanks to ensure the quality of the data from groundwater samples. An SRL is equivalent to a raised reporting level that is used in place of the reporting level used by the analyzing laboratory [long‑term method detection level (LT-MDL) or laboratory reporting level (LRL)] to reduce the probability of reporting false-positive detections. Evaluation of VOC-blank data was done in three stages: (1) identification of a set of representative quality‑control field blanks (QCFBs) to be used for calculation of SRLs and identification of VOCs amenable to the SRL approach, (2) evaluation of potential sources of contamination to blanks and groundwater samples by VOCs detected in field blanks, and (3) selection of appropriate SRLs from among four potential SRLs for VOCs detected in field blanks and application of those SRLs to the groundwater data. An important conclusion from this study is that to ensure the quality of the data from groundwater samples, it was necessary to apply different methods of determining SRLs from field blank data to different VOCs, rather than use the same method for all VOCs. Four potential SRL values were defined by using three approaches: two values were defined by using a binomial probability method based on one-sided, nonparametric upper confidence limits, one was defined as equal to the maximum concentration detected in the field blanks, and one was defined as equal to the maximum laboratory method detection level used during the period when samples were collected for the project. The differences in detection frequencies and concentrations among different types of blanks (laboratory instrument blanks, source-solution blanks, and field blanks collected with three different sampling equipment configurations) and groundwater samples were used to infer the sources and mechanisms of contamination for each VOC detection in field blanks. Other chemical data for the groundwater samples (oxidation-reduction state, co-occurrence of VOCs, groundwater age) and ancillary information about the well sites (land use, presence of known sources of contamination) were used to evaluate whether the patterns of detections of VOCs in groundwater samples before and after application of potential SRLs were plausible. On this basis, the appropriate SRL was selected for each VOC that was determined to require an SRL. The SRLs for ethylbenzene [0.06 microgram per liter (μg/L)], m- and p-xylenes (0.33 μg/L), o-xylene (0.12 μg/L), toluene (0.69 μg/L), and 1,2,4-trimethylbenzene (0.56 μg/L) corresponded to the highest concentrations detected in the QCFBs and were selected because they resulted in the most censoring of groundwater data. Comparisons of hydrocarbon ratios in groundwater samples and blanks and comparisons between detection frequencies of the five hydrocarbons in groundwater samples and different types of blanks suggested three dominant sources of contamination that affected groundwater samples and blanks: (1) ethylbenzene, m- and p-xylenes, o-xylene, and toluene from fuel or exhaust components sorbed onto sampling lines, (2) toluene from vials and the source blank water, and (3) 1,2,4-trimethylbenzene from materials used for collection of samples for radon-222 analysis.

Advances in low-defect multilayers for EUVL mask blanks

NASA Astrophysics Data System (ADS)

Folta, James A.; Davidson, J. Courtney; Larson, Cindy C.; Walton, Christopher C.; Kearney, Patrick A.

2002-07-01

Low-defect multilayer coatings are required to fabricate mask blanks for Extreme Ultraviolet Lithography (EUVL). The mask blanks consist of high reflectance EUV multilayers on low thermal expansion substrates. A defect density of 0.0025 printable defects/cm2 for both the mask substrate and the multilayer is required to provide a mask blank yield of 60 percent. Current low defect multilayer coating technology allows repeated coating-added defect levels of 0.05/cm2 for defects greater than 90 nm polystyrene latex sphere (PSL) equivalent size for lots of 20 substrates. Extended clean operation of the coating system at levels below 0.08/cm2 for 3 months of operation has also been achieved. Two substrates with zero added defects in the quality area have been fabricated, providing an existence proof that ultra low defect coatings are possible. Increasing the ion source-to-target distance from 410 to 560 mm to reduce undesired coating of the ion source caused the defect density to increase to 0.2/cm2. Deposition and etching diagnostic witness substrates and deposition pinhole cameras showed a much higher level of ion beam spillover (ions missing the sputter target) than expected. Future work will quantify beam spillover, and test designs to reduce spillover, if it is confirmed to be the cause of the increased defect level. The LDD system will also be upgraded to allow clean coating of standard format mask substrates. The upgrade will confirm that the low defect process developed on Si wafers is compatible with the standard mask format 152 mm square substrates, and will provide a clean supply of EUVL mask blanks needed to support development of EUVL mask patterning processes and clean mask handling technologies.

Development of high sensitivity and high speed large size blank inspection system LBIS

NASA Astrophysics Data System (ADS)

Ohara, Shinobu; Yoshida, Akinori; Hirai, Mitsuo; Kato, Takenori; Moriizumi, Koichi; Kusunose, Haruhiko

2017-07-01

The production of high-resolution flat panel displays (FPDs) for mobile phones today requires the use of high-quality large-size photomasks (LSPMs). Organic light emitting diode (OLED) displays use several transistors on each pixel for precise current control and, as such, the mask patterns for OLED displays are denser and finer than the patterns for the previous generation displays throughout the entire mask surface. It is therefore strongly demanded that mask patterns be produced with high fidelity and free of defect. To enable the production of a high quality LSPM in a short lead time, the manufacturers need a high-sensitivity high-speed mask blank inspection system that meets the requirement of advanced LSPMs. Lasertec has developed a large-size blank inspection system called LBIS, which achieves high sensitivity based on a laser-scattering technique. LBIS employs a high power laser as its inspection light source. LBIS's delivery optics, including a scanner and F-Theta scan lens, focus the light from the source linearly on the surface of the blank. Its specially-designed optics collect the light scattered by particles and defects generated during the manufacturing process, such as scratches, on the surface and guide it to photo multiplier tubes (PMTs) with high efficiency. Multiple PMTs are used on LBIS for the stable detection of scattered light, which may be distributed at various angles due to irregular shapes of defects. LBIS captures 0.3mμ PSL at a detection rate of over 99.5% with uniform sensitivity. Its inspection time is 20 minutes for a G8 blank and 35 minutes for G10. The differential interference contrast (DIC) microscope on the inspection head of LBIS captures high-contrast review images after inspection. The images are classified automatically.

Evaluation of TF11 attenuated-PSM mask blanks with DUV laser patterning

NASA Astrophysics Data System (ADS)

Xing, Kezhao; Björnberg, Charles; Karlsson, Henrik; Paulsson, Adisa; Beiming, Peter; Vedenpää, Jukka; Walford, Jonathan

2008-05-01

Tightening requirements on resolution, CD uniformity and positional accuracy push the development of improved photomask blanks. One such blank for 45nm node attenuated phase shift masks (att-PSM) provides a thinner chrome film, TF11, with a higher etch rate compared to previous generation NTAR5 att-PSM blanks from the same supplier. FEP-171, a positive chemically amplified resist, is commonly used in mask manufacturing for both e-beam and DUV laser pattern generators. TF11 chrome allows the FEP-171 resist thickness to be decreased at least down to 2000 Å while maintaining sufficient etch resistance, thereby improving photomask CD performance. The lower stress level in TF11 chrome films also reduces the image placement error induced by the material. In this study, TF11 chrome and FEP-171 resist are evaluated with exposures on a 248 nm DUV laser pattern generator, the Sigma7500. Patterning is first characterized for resist thicknesses of 2000 Å to 2600 Å in steps of 100 Å, assessing the minimum feature resolution, CD linearity, isolated-dense CD bias and dose sensitivity. Swing curve analysis shows a minimum near 2200 Å and a maximum near 2500 Å, corresponding closely to the reflectivity measurements provided by the blank supplier. The best overall patterning performance is obtained when operating near the swing maximum. The patterning performance is then studied in more detail with a resist thickness of 2550 Å that corresponds to the reflectivity maximum. This is compared to the results with 2000 Å resist, a standard thickness for e-beam exposures on TF11. The lithographic performance on NTAR5 att-PSM blanks with 3200 Å resist is also included for reference. This evaluation indicates that TF11 blanks with 2550 Å resist provide the best overall mask patterning performance obtained with the Sigma7500, showing a global CD uniformity below 4 nm (3s) and minimum feature resolution below 100 nm.

Collection methods and quality assessment for Esche-richia coli, water quality, and microbial source tracking data within Tumacácori National Historical Park and the upper Santa Cruz River, Arizona, 2015-16

USGS Publications Warehouse

Paretti, Nicholas; Coes, Alissa L.; Kephart, Christopher M.; Mayo, Justine

2018-03-05

Tumacácori National Historical Park protects the culturally important Mission, San José de Tumacácori, while also managing a portion of the ecologically diverse riparian corridor of the Santa Cruz River. This report describes the methods and quality assurance procedures used in the collection of water samples for the analysis of Escherichia coli (E. coli), microbial source tracking markers, suspended sediment, water-quality parameters, turbidity, and the data collection for discharge and stage; the process for data review and approval is also described. Finally, this report provides a quantitative assessment of the quality of the E. coli, microbial source tracking, and suspended sediment data.The data-quality assessment revealed that bias attributed to field and laboratory contamination was minimal, with E. coli detections in only 3 out of 33 field blank samples analyzed. Concentrations in the field blanks were several orders of magnitude lower than environmental concentrations. The microbial source tracking (MST) field blank was below the detection limit for all MST markers analyzed. Laboratory blanks for E. coli at the USGS Arizona Water Science Center and laboratory blanks for MST markers at the USGS Ohio Water Microbiology Laboratory were all below the detection limit. Irreplicate data for E. coli and suspended sediment indicated that bias was not introduced to the data by combining samples collected using discrete sampling methods with samples collected using automatic sampling methods.The split and sequential E. coli replicate data showed consistent analytical variability and a single equation was developed to explain the variability of E. coli concentrations. An additional analysis of analytical variability for E. coli indicated analytical variability around 18 percent relative standard deviation and no trend was observed in the concentration during the processing and analysis of multiple split-replicates. Two replicate samples were collected for MST and individual markers were compared for a base flow and flood sample. For the markers found in common between the two types of samples, the relative standard deviation for the base flow sample was more than 3 times greater than the markers in the flood sample. Sequential suspended sediment replicates had a relative standard deviation of about 1.3 percent, indicating that environmental and analytical variability was minimal.A holding time review and laboratory study analysis supported the extended holding times required for this investigation. Most concentrations for flood and base-flow samples were within the theoretical variability specified in the most probable number approach suggesting that extended hold times did not overly influence the final concentrations reported.

7 CFR 201.35 - Blank spaces.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Blank spaces. 201.35 Section 201.35 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS Labeling in General § 201.35 Blank spaces. Blank spaces on the label shall be deemed to imply the...

7 CFR 201.35 - Blank spaces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Blank spaces. 201.35 Section 201.35 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS Labeling in General § 201.35 Blank spaces. Blank spaces on the label shall be deemed to imply the...

7 CFR 201.35 - Blank spaces.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 3 2014-01-01 2014-01-01 false Blank spaces. 201.35 Section 201.35 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS Labeling in General § 201.35 Blank spaces. Blank spaces on the label shall be deemed to imply the...

7 CFR 201.35 - Blank spaces.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 3 2012-01-01 2012-01-01 false Blank spaces. 201.35 Section 201.35 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS Labeling in General § 201.35 Blank spaces. Blank spaces on the label shall be deemed to imply the...

7 CFR 201.35 - Blank spaces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Blank spaces. 201.35 Section 201.35 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS Labeling in General § 201.35 Blank spaces. Blank spaces on the label shall be deemed to imply the...

NHEXAS PHASE I REGION 5 STUDY--QA ANALYTICAL RESULTS FOR VOCS IN BLANKS

EPA Science Inventory

This data set includes analytical results for measurements of VOCs in 88 blank samples. Measurements were made for up to 23 VOCs in blank samples of air, water, and blood. Blank samples were used to assess the potential for sample contamination during collection, storage, shipmen...

NHEXAS PHASE I ARIZONA STUDY--QA ANALYTICAL RESULTS FOR PESTICIDES IN BLANK SAMPLES

EPA Science Inventory

The Pesticides in Blank Samples data set contains the analytical results of measurements of up to 4 pesticides in 43 blank samples from 29 households. Measurements were made in blank samples of dust, indoor and outdoor air, food and beverages, blood, urine, and dermal wipe resid...

An inventory of four-dimensional data sets for the earth sciences

NASA Technical Reports Server (NTRS)

Gregory, Terri

1989-01-01

The wide variety of data available to the diligent researcher and the myriad paths to obtaining it are emphasized. This inventory is an attempt to make accessible much of the four-dimensional data available in the world. In this quick-look catalog are listed separate data sets (Data Sets sections), sources of data including centers and large data bases (Sources section), and some data expected to be available in the future (Future Data section). In the Data Sets section, individual data sets are arranged alphabetically by institution, with those archived in the U.S.A. listed first, followed by those found elsewhere. The Sources section includes large data bases, centers, and directories. Sources are arranged alphabetically by country. This section is followed by a Future Data section which is a collection of data sets, experiments, and other future developments of which we are cognizant. A collection of further information and order blanks provided by some of the archiving institutions are presented in the appendix.

Method of analysis at the U.S. Geological Survey California Water Science Center, Sacramento Laboratory - determination of haloacetic acid formation potential, method validation, and quality-control practices

USGS Publications Warehouse

Zazzi, Barbara C.; Crepeau, Kathryn L.; Fram, Miranda S.; Bergamaschi, Brian A.

2005-01-01

An analytical method for the determination of haloacetic acid formation potential of water samples has been developed by the U.S. Geological Survey California Water Science Center Sacramento Laboratory. The haloacetic acid formation potential is measured by dosing water samples with chlorine under specified conditions of pH, temperature, incubation time, darkness, and residual-free chlorine. The haloacetic acids formed are bromochloroacetic acid, bromodichloroacetic acid, dibromochloroacetic acid, dibromoacetic acid, dichloroacetic acid, monobromoacetic acid, monochloroacetic acid, tribromoacetic acid, and trichloroacetic acid. They are extracted, methylated, and then analyzed using a gas chromatograph equipped with an electron capture detector. Method validation experiments were performed to determine the method accuracy, precision, and detection limit for each of the compounds. Method detection limits for these nine haloacetic acids ranged from 0.11 to 0.45 microgram per liter. Quality-control practices include the use of blanks, quality-control samples, calibration verification standards, surrogate recovery, internal standard, matrix spikes, and duplicates.

A Novel Hydrogel-Based Biosampling Approach

DTIC Science & Technology

2016-03-01

MONITORING AGENCY NAME(S) AND ADDRESS(ES) U.S. Army Edgewood Chemical Biological Center Seedling Program, APG, MD 21010-5424 10. SPONSOR/MONITOR’S...Std. Z39.18 ii Blank   iii PREFACE The work described in this report was authorized under the U.S. Army Edgewood Chemical Biological...a complex area of intensive, ongoing research. After a biorelease event, sampling is at the core of all pre- and post- decontamination analyses

Ready for the Future: Assessing the Collaborative Capacity of State Emergency Management Agencies

DTIC Science & Technology

2013-03-01

Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE March 2013...Preparedness) SEOC State Emergency Operations Center xiv SFI Strategic Foresight Initiative SPSS Statistical Package for the Social Sciences UASI... management discipline and to define the core capabilities to meet those needs. The Strategic Foresight Initiative (SFI) resulted in a vision document

Method of Making Lightweight, Single Crystal Mirror

NASA Technical Reports Server (NTRS)

Bly, Vincent T. (Inventor)

2015-01-01

A method of making a mirror from a single crystal blank may include fine grinding top and bottom surfaces of the blank to be parallel. The blank may then be heat treated to near its melting temperature. An optical surface may be created on an optical side of the blank. A protector may be bonded to the optical surface. With the protector in place, the blank may be light weighted by grinding a non-optical surface of the blank using computer controlled grinding. The light weighting may include creating a structure having a substantially minimum mass necessary to maintain distortion of the mirror within a preset limit. A damaged layer of the non-optical surface caused by light weighting may be removed with an isotropic etch and/or repaired by heat treatment. If an oxide layer is present, the entire blank may then be etched using, for example, hydrofluoric acid. A reflecting coating may be deposited on the optical surface.

Understanding EUV mask blank surface roughness induced LWR and associated roughness requirement

NASA Astrophysics Data System (ADS)

Yan, Pei-Yang; Zhang, Guojing; Gullikson, Eric M.; Goldberg, Ken A.; Benk, Markus P.

2015-03-01

Extreme ultraviolet lithography (EUVL) mask multi-layer (ML) blank surface roughness specification historically comes from blank defect inspection tool requirement. Later, new concerns on ML surface roughness induced wafer pattern line width roughness (LWR) arise. In this paper, we have studied wafer level pattern LWR as a function of EUVL mask surface roughness via High-NA Actinic Reticle Review Tool. We found that the blank surface roughness induced LWR at current blank roughness level is in the order of 0.5nm 3σ for NA=0.42 at the best focus. At defocus of ±40nm, the corresponding LWR will be 0.2nm higher. Further reducing EUVL mask blank surface roughness will increase the blank cost with limited benefit in improving the pattern LWR, provided that the intrinsic resist LWR is in the order of 1nm and above.

Setup of a Parameterized FE Model for the Die Roll Prediction in Fine Blanking using Artificial Neural Networks

NASA Astrophysics Data System (ADS)

Stanke, J.; Trauth, D.; Feuerhack, A.; Klocke, F.

2017-09-01

Die roll is a morphological feature of fine blanked sheared edges. The die roll reduces the functional part of the sheared edge. To compensate for the die roll thicker sheet metal strips and secondary machining must be used. However, in order to avoid this, the influence of various fine blanking process parameters on the die roll has been experimentally and numerically studied, but there is still a lack of knowledge on the effects of some factors and especially factor interactions on the die roll. Recent changes in the field of artificial intelligence motivate the hybrid use of the finite element method and artificial neural networks to account for these non-considered parameters. Therefore, a set of simulations using a validated finite element model of fine blanking is firstly used to train an artificial neural network. Then the artificial neural network is trained with thousands of experimental trials. Thus, the objective of this contribution is to develop an artificial neural network that reliably predicts the die roll. Therefore, in this contribution, the setup of a fully parameterized 2D FE model is presented that will be used for batch training of an artificial neural network. The FE model enables an automatic variation of the edge radii of blank punch and die plate, the counter and blank holder force, the sheet metal thickness and part diameter, V-ring height and position, cutting velocity as well as material parameters covered by the Hensel-Spittel model for 16MnCr5 (1.7131, AISI/SAE 5115). The FE model is validated using experimental trails. The results of this contribution is a FE model suitable to perform 9.623 simulations and to pass the simulated die roll width and height automatically to an artificial neural network.

Effects of process variation in short cycle stretch forming in beverage can production

NASA Astrophysics Data System (ADS)

Schneider, Matthias; Liewald, Mathias

2016-10-01

Short Cycle Stretch Forming (SCS) is an innovative stretch forming technology developed at the Institute for Metal Forming Technology (IFU) at the University of Stuttgart. The SCS technology combines plane pre-stretching and deep drawing operations within the same stroke of press ram. Material is yielding from the inner to the outer part of the sheet. The sheet thickness is reduced and denting resistance and yield stress are increased due to hardening effects. SCS-Technology is enhanced due to rotational-symmetrical bodies by applying this technology to a cupping process in tinplate can production. A process simulation for SCS-Cupping processes was conducted. Based on these results a tool was manufactured and commissioned. Experimental results showed that material yields from the middle of the blank to the outer area of the cup wall. Due to the volume of material, the initial diameter can be reduced and material costs can be saved. In this paper different process settings and their effect on the amount of material, which yielded from the middle of the blank to its outside, are observed in a number of experimental series. A blank holder is added to the process in order to avoid wrinkling. The influence of this additional blank holder is therefore investigated in a first experimental set-up by varying blank holder force. In a further investigation the effects of two materials with different thicknesses is observed. Finally, an experimental series is conducted to observe the effect of blank diameter on the SCS-Cupping process. The results of this paper show that SCS-Cupping offers a promising potential for material savings and outline main effects for this technology.

Spatial and temporal genetic structure of a river-resident Atlantic salmon (Salmo salar) after millennia of isolation

PubMed Central

Sandlund, Odd Terje; Karlsson, Sten; Thorstad, Eva B; Berg, Ole Kristian; Kent, Matthew P; Norum, Ine C J; Hindar, Kjetil

2014-01-01

The river-resident Salmo salar (“småblank”) has been isolated from other Atlantic salmon populations for 9,500 years in upper River Namsen, Norway. This is the only European Atlantic salmon population accomplishing its entire life cycle in a river. Hydropower development during the last six decades has introduced movement barriers and changed more than 50% of the river habitat to lentic conditions. Based on microsatellites and SNPs, genetic variation within småblank was only about 50% of that in the anadromous Atlantic salmon within the same river. The genetic differentiation (FST) between småblank and the anadromous population was 0.24. This is similar to the differentiation between anadromous Atlantic salmon in Europe and North America. Microsatellite analyses identified three genetic subpopulations within småblank, each with an effective population size Ne of a few hundred individuals. There was no evidence of reduced heterozygosity and allelic richness in contemporary samples (2005–2008) compared with historical samples (1955–56 and 1978–79). However, there was a reduction in genetic differentiation between sampling localities over time. SNP data supported the differentiation of småblank into subpopulations and revealed downstream asymmetric gene flow between subpopulations. In spite of this, genetic variation was not higher in the lower than in the upper areas. The meta-population structure of småblank probably maintains genetic variation better than one panmictic population would do, as long as gene flow among subpopulations is maintained. Småblank is a unique endemic island population of Atlantic salmon. It is in a precarious situation due to a variety of anthropogenic impacts on its restricted habitat area. Thus, maintaining population size and avoiding further habitat fragmentation are important. PMID:24967074

Opportunity Landing Spot Panorama (3-D Model)

NASA Technical Reports Server (NTRS)

2004-01-01

The rocky outcrop traversed by the Mars Exploration Rover Opportunity is visible in this three-dimensional model of the rover's landing site. Opportunity has acquired close-up images along the way, and scientists are using the rover's instruments to closely examine portions of interest. The white fragments that look crumpled near the center of the image are portions of the airbags. Distant scenery is displayed on a spherical backdrop or 'billboard' for context. Artifacts near the top rim of the crater are a result of the transition between the three-dimensional model and the billboard. Portions of the terrain model lacking sufficient data appear as blank spaces or gaps, colored reddish-brown for better viewing. This image was generated using special software from NASA's Ames Research Center and a mosaic of images taken by the rover's panoramic camera.

[figure removed for brevity, see original site] Click on image for larger view

The rocky outcrop traversed by the Mars Exploration Rover Opportunity is visible in this zoomed-in portion of a three-dimensional model of the rover's landing site. Opportunity has acquired close-up images along the way, and scientists are using the rover's instruments to closely examine portions of interest. The white fragments that look crumpled near the center of the image are portions of the airbags. Distant scenery is displayed on a spherical backdrop or 'billboard' for context. Artifacts near the top rim of the crater are a result of the transition between the three-dimensional model and the billboard. Portions of the terrain model lacking sufficient data appear as blank spaces or gaps, colored reddish-brown for better viewing. This image was generated using special software from NASA's Ames Research Center and a mosaic of images taken by the rover's panoramic camera.

NHEXAS PHASE I ARIZONA STUDY--QA ANALYTICAL RESULTS FOR METALS IN BLANK SAMPLES

EPA Science Inventory

The Metals in Blank Samples data set contains the analytical results of measurements of up to 27 metals in 82 blank samples from 26 households. Measurements were made in blank samples of dust, indoor and outdoor air, personal air, food, beverages, blood, urine, and dermal wipe r...

Hydroforming Of Patchwork Blanks — Numerical Modeling And Experimental Validation

NASA Astrophysics Data System (ADS)

Lamprecht, Klaus; Merklein, Marion; Geiger, Manfred

2005-08-01

In comparison to the commonly applied technology of tailored blanks the concept of patchwork blanks offers a number of additional advantages. Potential application areas for patchwork blanks in automotive industry are e.g. local reinforcements of automotive closures, structural reinforcements of rails and pillars as well as shock towers. But even if there is a significant application potential for patchwork blanks in automobile production, industrial realization of this innovative technique is decelerated due to a lack of knowledge regarding the forming behavior and the numerical modeling of patchwork blanks. Especially for the numerical simulation of hydroforming processes, where one part of the forming tool is replaced by a fluid under pressure, advanced modeling techniques are required to ensure an accurate prediction of the blanks' forming behavior. The objective of this contribution is to provide an appropriate model for the numerical simulation of patchwork blanks' forming processes. Therefore, different finite element modeling techniques for patchwork blanks are presented. In addition to basic shell element models a combined finite element model consisting of shell and solid elements is defined. Special emphasis is placed on the modeling of the weld seam. For this purpose the local mechanical properties of the weld metal, which have been determined by means of Martens-hardness measurements and uniaxial tensile tests, are integrated in the finite element models. The results obtained from the numerical simulations are compared to experimental data from a hydraulic bulge test. In this context the focus is laid on laser- and spot-welded patchwork blanks.

System 6: A pricing strategy for long blanks

Treesearch

Hugh W. Reynolds; Bruce G. Hansen; Bruce G. Hansen

1986-01-01

In System 6, small-diameter, low-grade hardwood timber is used to make blanks in standard sizes. Blanks are made in one thickness and one quality class but in all the standard lengths during each production run. The quantity of blanks per length can be varied, while keeping total yield high, by using proper production control techniques. However, when the percentage of...

Status of EUVL mask development in Europe (Invited Paper)

NASA Astrophysics Data System (ADS)

Peters, Jan H.

2005-06-01

EUV lithography is the prime candidate for the next generation lithography technology after 193 nm immersion lithography. The commercial onset for this technology is expected for the 45 nm half-pitch technology or below. Several European and national projects and quite a large number of companies and research institutions in Europe work on various aspects of the technological challenges to make EUV a commercially viable technology in the not so far future. Here the development of EUV sources, the development of an EUV exposure tools, metrology tools dedicated for characterization of mask, the production of EUV mask blanks and the mask structuring itself are the key areas in which major activities can be found. In this talk we will primarily focus on those activities, which are related to establish an EUV mask supply chain with all its ingredients from substrate production, polishing, deposition of EUV layers, blank characterization, mask patterning process and the consecutive metrology and defect inspection as well as shipping and handling from blank supply to usage in the wafer fab. The EUV mask related projects on the national level are primarily supported by the French Ministry of Economics and Finance (MinEFi) and the German Ministry of Education and Research (BMBF).

The DTIC Review. Volume 5, Number 2. Real-Time Communications

DTIC Science & Technology

2000-12-01

appreciate your comments. Kurt N. Molholm Administrator THIS PAGE INTENTIONALLY LEFT BLANK The DTIC Review Defense Technical Information Center TABLE OF...assisted by Captain Dino Perone, CW2 Kurt Prokarym, CW2 Earl Johnson, SSG Case, MSG Nancy MacDonald, SGM Jessie Husband, and many other junior non...Navy IT-21 Audit Policy 07 Jul 2000 28 PAGES 01 Sep 1999 61 PAGES PERSONAL AUTHORS: Gevelber, Michael; PERSONAL AUTHORS: Kremer , H. S. Wroblewski

Unmanned Systems: A Lab-Based Robotic Arm for Grasping

DTIC Science & Technology

2015-06-01

Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE June 2015 3. REPORT TYPE AND DATES COVERED...experiments. The focus of this project is to understand and apply the kinematics and dynamics for a 6 degree of freedom (DOF) Kinova JACO robotic arm...Implementation, (3) and Operational Demonstrations This research project centered on Phase 1, while focusing on three subareas: • JACO Manipulator Set Up And

Bis-aptazyme sensors for hepatitis C virus replicase and helicase without blank signal

PubMed Central

Cho, Suhyung; Kim, Ji-Eun; Lee, Bo-Rahm; Kim, June-Hyung; Kim, Byung-Gee

2005-01-01

The fusion molecule (i.e. aptazyme) of aptamer and hammerhead ribozyme was developed as in situ sensor. Previously, the hammerhead ribozyme conjugated with aptamer through its stem II module showed a significant blank signal by self-cleavage. To reduce or remove its self-cleavage activity in the absence of target molecule, rational designs were attempted by reducing the binding affinity of the aptazyme to its RNA substrate, while maintaining the ribonuclease activity of the aptazyme. Interestingly, the bis-aptazymes which comprise the two aptamer-binding sites at both stem I and stem III of the hammerhead ribozyme showed very low blank signals, and their ratios of reaction rate constants, i.e. signal to noise ratios, were several tens to hundred times higher than those of the stem II-conjugated bis-aptazymes. The reduction in the blank signals seems to be caused by a higher dissociation constant between the main strand of the bis-aptazyme and its substrate arising from multi-point base-pairing of the bis-aptazymes. The bis-aptazymes for HCV replicase and helicase showed high selectivity against other proteins, and a linear relationship existed between their ribozyme activities and the target concentrations. In addition, a bis-aptazyme of dual functions was designed by inserting both aptamers for HCV replicase and helicase into the stem I and stem III of hammerhead ribozyme, respectively, and it also showed greater sensitivity and specificity for both proteins without blank signal. PMID:16314308

Radial-rotation profile forming: A new processing technology of incremental sheet metal forming

NASA Astrophysics Data System (ADS)

Laue, Robert; Härtel, Sebastian; Awiszus, Birgit

2018-05-01

Incremental forming processes (i.e., spinning) of sheet metal blanks into cylindrical cups are suitable for lower lot sizes. The produced cups were frequently used as preforms to produce workpieces in further forming steps with additional functions like profiled hollow parts [1]. The incremental forming process radial-rotation profile forming has been developed to enable the production of profiled hollow parts with low sheet thinning and good geometrical accuracy. The two principal forming steps are the production of the preform by rotational swing-folding [2] and the subsequent radial profiling of the hollow part in one clamping position. The rotational swing-folding process is based on a combination of conventional spinning and swing-folding. Therefore, a round blank rotates on a profiled mandrel and due to the swinging of a cylindrical forming tool, the blank is formed to a cup with low sheet thinning. In addition, thickening results at the edge of the blank and wrinkling occurs. However, the wrinkles are formed into the indentation of the profiled mandrel and can be reshaped as an advantage in the second process step, the radial profiling. Due to the rotation and continuous radial feed of a profiled forming tool to the profiled mandrel, the axial profile is formed in the second process step. Because of the minor relative movement in axial direction between tool and blank, low sheet thinning occurs. This is an advantage of the principle of the process.

Quality of volatile organic compound data from groundwater and surface water for the National Water-Quality Assessment Program, October 1996–December 2008

USGS Publications Warehouse

Bender, David A.; Zogorski, John S.; Mueller, David K.; Rose, Donna L.; Martin, Jeffrey D.; Brenner, Cassandra K.

2011-01-01

This report describes the quality of volatile organic compound (VOC) data collected from October 1996 to December 2008 from groundwater and surface-water sites for the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. The VOC data described were collected for three NAWQA site types: (1) domestic and public-supply wells, (2) monitoring wells, and (3) surface-water sites. Contamination bias, based on the 90-percent upper confidence limit (UCL) for the 90th percentile of concentrations in field blanks, was determined for VOC samples from the three site types. A way to express this bias is that there is 90-percent confidence that this amount of contamination would be exceeded in no more than 10 percent of all samples (including environmental samples) that were collected, processed, shipped, and analyzed in the same manner as the blank samples. This report also describes how important native water rinsing may be in decreasing carryover contamination, which could be affecting field blanks. The VOCs can be classified into four contamination categories on the basis of the 90-percent upper confidence limit (90-percent UCL) concentration distribution in field blanks. Contamination category 1 includes compounds that were not detected in any field blanks. Contamination category 2 includes VOCs that have a 90-percent UCL concentration distribution in field blanks that is about an order of magnitude lower than the concentration distribution of the environmental samples. Contamination category 3 includes VOCs that have a 90-percent UCL concentration distribution in field blanks that is within an order of magnitude of the distribution in environmental samples. Contamination category 4 includes VOCs that have a 90-percent UCL concentration distribution in field blanks that is at least an order of magnitude larger than the concentration distribution of the environmental samples. Fifty-four of the 87 VOCs analyzed in samples from domestic and public-supply wells were not detected in field blanks (contamination category 1), and 33 VOC were detected in field blanks. Ten of the 33 VOCs had a 90-percent UCL concentration distribution in field blanks that was at least an order of magnitude lower than the concentration distribution in environmental samples (contamination category 2). These 10 VOCs may have had some contamination bias associated with the environmental samples, but the potential contamination bias was negligible in comparison to the environmental data; therefore, the field blanks were assumed to be representative of the sources of contamination bias affecting the environmental samples for these 10 VOCs. Seven VOCs had a 90-percent UCL concentration distribution of the field blanks that was within an order of magnitude of the concentration distribution of the environmental samples (contamination category 3). Sixteen VOCs had a 90-percent UCL concentration distribution in the field blanks that was at least an order of magnitude greater than the concentration distribution of the environmental samples (contamination category 4). Field blanks for these 16 VOCs appear to be nonrepresentative of the sources of contamination bias affecting the environmental samples because of the larger concentration distributions (and sometimes higher frequency of detection) in field blanks than in environmental samples. Forty-three of the 87 VOCs analyzed in samples from monitoring wells were not detected in field blanks (contamination category 1), and 44 VOCs were detected in field blanks. Eight of the 44 VOCs had a 90-percent UCL concentration distribution in field blanks that was at least an order of magnitude lower than concentrations in environmental samples (contamination category 2). These eight VOCs may have had some contamination bias associated with the environmental samples, but the potential contamination bias was negligible in comparison to the environmental data; therefore, the field blanks were assumed to be representative. Seven VOCs had a 90-percent UCL concentration distribution in field blanks that was of the same order of magnitude as the concentration distribution of the environmental samples (contamination category 3). Twenty-nine VOCs had a 90-percent UCL concentration distribution in the field blanks that was an order of magnitude greater than the distribution of the environmental samples (contamination category 4). Field blanks for these 29 VOCs appear to be nonrepresentative of the sources of contamination bias to the environmental samples. Fifty-four of the 87 VOCs analyzed in surface-water samples were not detected in field blanks (category 1), and 33 VOC were detected in field blanks. Sixteen of the 33 VOCs had a 90-percent UCL concentration distribution in field blanks that was at least an order of magnitude lower than the concentration distribution in environmental samples (contamination category 2). These 16 VOCs may have had some contamination bias associated with the environmental samples, but the potential contamination bias was negligible in comparison to the environmental data; therefore, the field blanks were assumed to be representative. Ten VOCs had a 90-percent UCL concentration distribution in field blanks that was similar to the concentration distribution of environmental samples (contamination category 3). Seven VOCs had a 90-percent UCL concentration distribution in the field blanks that was greater than the concentration distribution in environmental samples (contamination category 4). Field-blank samples for these seven VOCs appear to be nonrepresentative of the sources of contamination bias to the environmental samples. The relation between the detection of a compound in field blanks and the detection in subsequent environmental samples appears to be minimal. The median minimum percent effectiveness of native water rinsing is about 79 percent for the 19 VOCs detected in more than 5 percent of field blanks from all three site types. The minimum percent effectiveness of native water rinsing (10 percent) was for toluene in surface-water samples, likely because of the large detection frequency of toluene in surface-water samples (about 79 percent) and in the associated field-blank samples (46.5 percent). The VOCs that were not detected in field blanks (contamination category 1) from the three site types can be considered free of contamination bias, and various interpretations for environmental samples, such as VOC detection frequency at multiple assessment levels and comparisons of concentrations to benchmarks, are not limited for these VOCs. A censoring level for making comparisons at different assessment levels among environmental samples could be applied to concentrations of 9 VOCs in samples from domestic and public-supply wells, 16 VOCs in samples from monitoring wells, and 9 VOCs in surface-water samples to account for potential low-level contamination bias associated with these selected VOCs. Bracketing the potential contamination by comparing the detection and concentration statistics with no censoring applied to the potential for contamination bias on the basis of the 90-percent UCL for the 90th-percentile concentrations in field blanks may be useful when comparisons to benchmarks are done in a study. The VOCs that were not detected in field blanks (contamination category 1) from the three site types can be considered free of contamination bias, and various interpretations for environmental samples, such as VOC detection frequency at multiple assessment levels and comparisons of concentrations to benchmarks, are not limited for these VOCs. A censoring level for making comparisons at different assessment levels among environmental samples could be applied to concentrations of 9 VOCs in samples from domestic and public-supply wells, 16 VOCs in samples from monitoring wells, and 9 VOCs in surface-water samples to account for potential low-level contamination bias associated with these selected VOCs. Bracketing the potential contamination by comparing the detection and concentration statistics with no censoring applied to the potential for contamination bias on the basis of the 90-percent UCL for the 90th-percentile concentrations in field blanks may be useful when comparisons to benchmarks are done in a study.

EUV mask pilot line at Intel Corporation

NASA Astrophysics Data System (ADS)

Stivers, Alan R.; Yan, Pei-Yang; Zhang, Guojing; Liang, Ted; Shu, Emily Y.; Tejnil, Edita; Lieberman, Barry; Nagpal, Rajesh; Hsia, Kangmin; Penn, Michael; Lo, Fu-Chang

2004-12-01

The introduction of extreme ultraviolet (EUV) lithography into high volume manufacturing requires the development of a new mask technology. In support of this, Intel Corporation has established a pilot line devoted to encountering and eliminating barriers to manufacturability of EUV masks. It concentrates on EUV-specific process modules and makes use of the captive standard photomask fabrication capability of Intel Corporation. The goal of the pilot line is to accelerate EUV mask development to intersect the 32nm technology node. This requires EUV mask technology to be comparable to standard photomask technology by the beginning of the silicon wafer process development phase for that technology node. The pilot line embodies Intel's strategy to lead EUV mask development in the areas of the mask patterning process, mask fabrication tools, the starting material (blanks) and the understanding of process interdependencies. The patterning process includes all steps from blank defect inspection through final pattern inspection and repair. We have specified and ordered the EUV-specific tools and most will be installed in 2004. We have worked with International Sematech and others to provide for the next generation of EUV-specific mask tools. Our process of record is run repeatedly to ensure its robustness. This primes the supply chain and collects information needed for blank improvement.

Modified blank ammunition injuries.

PubMed

Ogunc, Gokhan I; Ozer, M Tahir; Coskun, Kagan; Uzar, Ali Ihsan

2009-12-15

Blank firing weapons are designed only for discharging blank ammunition cartridges. Because they are cost-effective, are easily accessible and can be modified to live firearms plus their unclear legal situation in Turkish Law makes them very popular in Turkey. 2004 through 2008, a total of 1115 modified blank weapons were seized in Turkey. Blank firing weapons are easily modified by owners, making them suitable for discharging live firearm ammunition or modified blank ammunitions. Two common methods are used for modification of blank weapons. After the modification, these weapons can discharge the live ammunition. However, due to compositional durability problems with these types of weapons; the main trend is to use the modified blank ammunitions rather than live firearm ammunition fired from modified blank firing weapons. In this study, two types of modified blank weapons and two types of modified blank cartridges were tested on three different target models. Each of the models' shooting side was coated with 1.3+/-2 mm thickness chrome tanned cowhide as a skin simulant. The first model was only coated with skin simulant. The second model was coated with skin simulant and 100% cotton police shirt. The third model was coated with skin simulant and jean denim. After the literature evaluation four high risky anatomic locations (the neck area; the eyes; the thorax area and inguinal area) were pointed out for the steel and lead projectiles are discharged from the modified blank weapons especially in close range (0-50 cm). The target models were designed for these anatomic locations. For the target models six Transparent Ballistic Candle blocks (TCB) were prepared and divided into two test groups. The first group tests were performed with lead projectiles and second group with steel projectile. The shortest penetration depth (lead projectile: 4.358 cm; steel projectile 8.032 cm) was recorded in the skin simulant and jean denim coated block for both groups. In both groups, the longest penetration depth (lead projectile: 6.434 cm; steel projectile 8.608 cm) was recorded in the only skin simulant coated block. And the penetration depth of skin simulant and 100% cotton police shirt coated model was 5.870 cm for lead projectile; 8.440 cm for steel projectile. According to penetration results, national and international legislations and production standards should be re-evaluated in order to prevent the modification of blank weapons and ammunitions. There are three methods for preventing modification of blank weapons: completely closed barrel structure; intersected restrain pieces application; eccentric barrel structure.

Process Design of Aluminum Tailor Heat Treated Blanks.

PubMed

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-12-09

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO₂ and NO x emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation.

Process Design of Aluminum Tailor Heat Treated Blanks

PubMed Central

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-01-01

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO2 and NOx emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation. PMID:28793727

Design and evaluation of a field study on the contamination of selected volatile organic compounds and wastewater-indicator compounds in blanks and groundwater samples

USGS Publications Warehouse

Thiros, Susan A.; Bender, David A.; Mueller, David K.; Rose, Donna L.; Olsen, Lisa D.; Martin, Jeffrey D.; Bernard, Bruce; Zogorski, John S.

2011-01-01

The Field Contamination Study (FCS) was designed to determine the field processes that tend to result in clean field blanks and to identify potential sources of contamination to blanks collected in the field from selected volatile organic compounds (VOCs) and wastewater-indicator compounds (WICs). The VOCs and WICs analyzed in the FCS were detected in blanks collected by the U.S. Geological Survey (USGS) National Water-Quality Assessment (NAWQA) Program during 1996–2008 and 2002–08, respectively. To minimize the number of variables, the study required ordering of supplies just before sampling, storage of supplies and equipment in clean areas, and use of adequate amounts of purge-and-trap volatile-grade methanol and volatile pesticide-grade blank water (VPBW) to clean sampling equipment and to collect field blanks.Blanks and groundwater samples were collected during 2008–09 at 16 sites, which were a mix of water-supply and monitoring wells, located in 9 States. Five different sample types were collected for the FCS at each site: (1) a source-solution blank collected at the USGS National Water Quality Laboratory (NWQL) using laboratory-purged VPBW, (2) source-solution blanks collected in the field using laboratory-purged VPBW, (3) source-solution blanks collected in the field using field-purged VPBW, (4) a field blank collected using field-purged VPBW, and (5) a groundwater sample collected from a well. The source-solution blank and field-blank analyses were used to identify, quantify, and document extrinsic contamination and to help determine the sources and causes of data-quality problems that can affect groundwater samples.Concentrations of compounds detected in FCS analyses were quantified and results were stored in the USGS National Water Information System database after meeting rigorous identification and quantification criteria. The study also utilized information provided by laboratory analysts about evidence indicating the presence of selected compounds, using less rigorous identification criteria than is required for reporting data to the National Water Information System database. For the FCS, these data are considered adequate to indicate "evidence of presence," and were used only for diagnostic purposes. Evidence of VOCs and WICs at low concentrations near or less than the long-term method detection level can indicate a contamination problem that could affect future datasets if method detection levels were ever to be lowered.

Evaluation of Quality-Assurance/Quality-Control Data Collected by the U.S. Geological Survey from Wells and Springs between the Southern Boundary of the Idaho National Engineering and Environmental Laboratory and the Hagerman Area, Idaho, 1989 through 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, L.M.; Bartholomay, R.C.; Campbell, L.J.

1998-10-01

The U.S. Geological (USGS) and the Idaho Department of Water Resources, in cooperation with the U.S. Department of Energy, collected and analyzed water samples to monitor the water quality of the Snake River Plain aquifer from the southern boundary of the Idaho National Engineering and Environmental Laboratory to the Hagerman area, Idaho. Concurrently, replicate samples and blank samples were collected and analyzed as part of the quality-assurance/quality-control program. Samples were analyzed from inorganic constituents, gross radioactivity and radionuclides, organic constituents, and stable isotopes. To evaluate the precision of field and laboratory methods, analytical results of the water-quality and replicate samplesmore » were compared statistically for equivalence on the basis of the precision associated with each result. Statistical comparisons of the data indicated that 95 percent of the results of the replicate pairs were equivalent. Blank-sample analytical results indicated th at the inorganic blank water and volatile organic compound blank water from the USGS National Water Quality Laboratory and the distilled water from the Idaho Department of Water Resources were suitable for blanks; blank water from other sources was not. Equipment-blank analytical results were evaluated to determine if a bias had been introduced and possible sources of bias. Most equipment blanks were analyzed for trace elements and volatile organic compounds; chloroform was found in one equipment blank. Two of the equipment blanks were prepared after collection and analyses of the water-quality samples to determine whether contamination had been introduced during the sampling process. Results of one blank indicated that a hose used to divert water away from pumps and electrical equipment had contaminated the samples with some volatile organic compounds. Results of the other equipment blank, from the apparatus used to filter dissolved organic carbon samples, indicated that the filtering apparatus did not affect water-quality samples.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Pei-Yang; Zhang, Guojing; Gullickson, Eric M.

Extreme ultraviolet lithography (EUVL) mask multi-layer (ML) blank surface roughness specification historically comes from blank defect inspection tool requirement. Later, new concerns on ML surface roughness induced wafer pattern line width roughness (LWR) arise. In this paper, we have studied wafer level pattern LWR as a function of EUVL mask surface roughness via High-NA Actinic Reticle Review Tool. We found that the blank surface roughness induced LWR at current blank roughness level is in the order of 0.5nm 3σ for NA=0.42 at the best focus. At defocus of ±40nm, the corresponding LWR will be 0.2nm higher. Further reducing EUVL maskmore » blank surface roughness will increase the blank cost with limited benefit in improving the pattern LWR, provided that the intrinsic resist LWR is in the order of 1nm and above.« less

Method of making dished ion thruster grids

NASA Technical Reports Server (NTRS)

Banks, B. A. (Inventor)

1975-01-01

A pair of flat grid blanks are clamped together at their edges with an impervious metal sheet on top. All of the blanks and sheets are dished simultaneously by forcing fluid to inflate an elastic sheet which contacts the bottom grid blank. A second impervious metal sheet is inserted between the two grid blanks if the grids have high percentage open areas. The dished grids are stress relieved simultaneously.

Effects of Blank Curvature and Tool Conditions on the Spring Back of Thin Sheet Panel Formed through Local Embossing and Edge L-Bending

NASA Astrophysics Data System (ADS)

Park, Keecheol; Park, Jongyoun; Nam, Jaebok

2011-08-01

Due to the application of thinner sheet steels, the stamped panels in the forming process, generally, are severely distorted. The wavy shape of embossed panel finally converted to residual stress embedded in the panel at final forming (edge L-bending) and it is known as the cause of twisting and oil canning of spring backed panel. Another important source of stamped shape deviation is the curvature of blank. The effects of blank curvature on the shape defects (panel curvature and twisting) after stamping were investigated from defective panel analysis, model experiment and stamping simulation. And the effect of tool conditions (BHF and bead height change) on spring backed shape of real TV bottom chassis were studied. The initial curvature of blank was remained in the flat area of stamped panels as width directional curvature. It converted from length direction curvature of blank. The curvature of initial blank reduced the wavy shape after local emboss forming, but twisting after edge L-bending was increased at large blank curvature cases. The effects of emboss forming conditions, the forming heights and blank holding force were studied and it was found that the wavy shape of stamped sheet was rapidly changed although the forming conditions altered very small amount.

Consolidation quality and mechanical performance of stamp formed tailored blanks produced by rapid AFP

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

2018-05-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The combination with rapid AFP as blank manufacturing technology can further extend the applicability of stamp forming by allowing rapid lay-up of tailored blanks and offering partial preconsolidation. In an experimental study it is demonstrated that high quality laminates with good flexural strength can be obtained by following this process route. The consolidation of ply-drop regions is demonstrated by flat laminates with a thickness step. The influence of fiber orientations, blank-tooling misalignments and AFP tolerances is investigated.

Ultra-Low Level Plutonium Isotopes in the NIST SRM 4355A (Peruvian Soil-1)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Inn, Kenneth G.; LaRosa, Jerome; Nour, Svetlana

2009-05-31

For more than 20 years, countries and their agencies which monitor discharge sites and storage facilities have relied on the National Institute of Standards and Technology (NIST) Standard Reference Material (SRM) 4355 Peruvian Soil reference material. Its low fallout contamination makes it an ideal soil blank for measurements associated with terrestrial pathway to man studies. Presently, SRM 4355 is out of stock, and a new batch of the Peruvian soil is currently under development as future NIST SRM 4355A. Both environmental radioanalytical laboratories and mass spectrometry communities will benefit from this SRM. The former must assess their laboratory contamination andmore » measurement detection limits by measurement of blank sample material. The Peruvian Soil is so low in anthropogenic radionuclides that it is a suitable virtual blank. On the other hand, mass spectrometric laboratories have high sensitivity instruments that are capable of quantitative isotopic measurements at low plutonium levels of the SRM 4355 (first Peruvian Soil SRM) that provided the mass spectrometric community with the calibration, quality control, and testing material needed for methods development, and legal defensibility. The quantification of the ultra-low plutonium content in the SRM 4355A was a considerable challenge for the mass spectrometric laboratories. Careful blank control and correction, isobaric interferences, instrument stability, peak assessment, and detection assessment were necessary. Furthermore, a systematic statistical evaluation of the measurement results and considerable discussions with the mass spectroscopy metrologists were needed to derive the certified values and uncertainties. SRM 4355A will provide the mass spectrometric community with the quality control and testing material needed for higher sensitivity methods development, and legal defensibility.« less

Quality-Assurance Data for Routine Water Analyses by the U.S. Geological Survey Laboratory in Troy, New York-July 1997 through June 1999

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2006-01-01

The laboratory for analysis of low-ionic-strength water at the U.S. Geological Survey (USGS) Water Science Center in Troy, N.Y., analyzes samples collected by USGS projects throughout the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures that were developed to ensure proper sample collection, processing, and analysis. The quality-assurance/quality-control data for the time period addressed in this report were stored in the laboratory's SAS data-management system, which provides efficient review, compilation, and plotting of data. This report presents and discusses results of quality-assurance and quality- control samples analyzed from July 1997 through June 1999. Results for the quality-control samples for 18 analytical procedures were evaluated for bias and precision. Control charts indicate that data for eight of the analytical procedures were occasionally biased for either high-concentration and (or) low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, total monomeric aluminum, total aluminum, ammonium, calcium, chloride, specific conductance, and sulfate. The data from the potassium and sodium analytical procedures are insufficient for evaluation. Results from the filter-blank and analytical-blank analyses indicate that the procedures for 11 of 13 analytes were within control limits, although the concentrations for blanks were occasionally outside the control limits. Blank analysis results for chloride showed that 22 percent of blanks did not meet data-quality objectives and results for dissolved organic carbon showed that 31 percent of the blanks did not meet data-quality objectives. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in the procedures for 14 of the 18 analytes. At least 90 percent of the samples met data-quality objectives for all analytes except total aluminum (70 percent of samples met objectives) and potassium (83 percent of samples met objectives). Results of the USGS interlaboratory Standard Reference Sample (SRS) Project indicated good data quality for most constituents over the time period. The P-sample (low-ionic-strength constituents) analysis had good ratings in two of these studies and a satisfactory rating in the third. The results of the T-sample (trace constituents) analysis indicated high data quality with good ratings in all three studies. The N-sample (nutrient constituents) studies had one each of excellent, good, and satisfactory ratings. Results of Environment Canada's National Water Research Institute (NWRI) program indicated that at least 80 percent of the samples met data-quality objectives for 9 of the 13 analytes; the exceptions were dissolved organic carbon, ammonium, chloride, and specific conductance. Data-quality objectives were not met for dissolved organic carbon in two NWRI studies, but all of the samples were within control limits for the last study. Data-quality objectives were not met in 41 percent of samples analyzed for ammonium, 25 percent of samples analyzed for chloride, and 30 percent of samples analyzed for specific conductance. Results from blind reference-sample analyses indicated that data-quality objectives were met by at least 84 percent of the samples analyzed for calcium, chloride, magnesium, pH, and potassium. Data-quality objectives were met by 73 percent of those analyzed for sulfate. The data-quality objective was not met for sodium. The data are insufficient for evaluation of the specific conductance results.

Analysis and Evaluation of Forecasting Methods and Tools to Predict Future Demand for Secondary Chemical-Biological Configuration Items

DTIC Science & Technology

2013-06-01

quantity, the lead time, the process quality and the number of deliveries (Yang & Pan, 2004). Inventory management systems are classified as either...22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank... managed by the Defense Logistics Agency (DLA), Edgewood Chemical Biological Center (ECBC) must be able to complete reviews of all procurement

Migrating Department of Defense (DoD) Web Service Based Applications to Mobile Computing Platforms

DTIC Science & Technology

2012-03-01

World Wide Web Consortium (W3C) Geolocation API to identify the device’s location and then center the map on the device. Finally, we modify the entry...THIS PAGE INTENTIONALLY LEFT BLANK xii List of Acronyms and Abbreviations API Application Programming Interface CSS Cascading Style Sheets CLIMO...Java API for XML Web Services Reference Implementation JS JavaScript JSNI JavaScript Native Interface METOC Meteorological and Oceanographic MAA Mobile

On The gamma-ray emission from Reticulum II and other dwarf galaxies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooper, Dan; Linden, Tim

2015-09-01

The recent discovery of ten new dwarf galaxy candidates by the Dark Energy Survey (DES) and the Panoramic Survey Telescope and Rapid Response System (Pan-STARRS) could increase the Fermi Gamma-Ray Space Telescope's sensitivity to annihilating dark matter particles, potentially enabling a definitive test of the dark matter interpretation of the long-standing Galactic Center gamma-ray excess. In this paper, we compare the previous analyses of Fermi data from the directions of the new dwarf candidates (including the relatively nearby Reticulum II) and perform our own analysis, with the goal of establishing the statistical significance of any gamma-ray signal from these sources.more » We confirm the presence of an excess from Reticulum II, with a spectral shape that is compatible with the Galactic Center signal. The significance of this emission is greater than that observed from 99.84% of randomly chosen high-latitude blank-sky locations, corresponding to a local detection significance of 3.2σ. We caution that any dark matter interpretation of this excess must be validated through observations of additional dwarf spheroidal galaxies, and improved calculations of the relative J-factor of dwarf spheroidal galaxies. We improve upon the standard blank-sky calibration approach through the use of multi-wavelength catalogs, which allow us to avoid regions that are likely to contain unresolved gamma-ray sources.« less

Computer-aided design of bevel gear tooth surfaces

NASA Technical Reports Server (NTRS)

Shuo, Hung Chang; Huston, Ronald L.; Coy, John J.

1989-01-01

This paper presents a computer-aided design procedure for generating bevel gears. The development is based on examining a perfectly plastic, cone-shaped gear blank rolling over a cutting tooth on a plane crown rack. The resulting impression on the plastic gear blank is the envelope of the cutting tooth. This impression and envelope thus form a conjugate tooth surface. Equations are presented for the locus of points on the tooth surface. The same procedures are then extended to simulate the generation of a spiral bevel gear. The corresponding governing equations are presented.

Computer aided design of bevel gear tooth surfaces

NASA Technical Reports Server (NTRS)

Chang, S. H.; Huston, R. L.; Coy, J. J.

1989-01-01

This paper presents a computer-aided design procedure for generating bevel gears. The development is based on examining a perfectly plastic, cone-shaped gear blank rolling over a cutting tooth on a plane crown rack. The resulting impression on the plastic gear blank is the envelope of the cutting tooth. This impression and envelope thus form a conjugate tooth surface. Equations are presented for the locus of points on the tooth surface. The same procedures are then extended to simulate the generation of a spiral bevel gear. The corresponding governing equations are presented.

Efficient simulation of press hardening process through integrated structural and CFD analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palaniswamy, Hariharasudhan; Mondalek, Pamela; Wronski, Maciek

Press hardened steel parts are being increasingly used in automotive structures for their higher strength to meet safety standards while reducing vehicle weight to improve fuel consumption. However, manufacturing of sheet metal parts by press hardening process to achieve desired properties is extremely challenging as it involves complex interaction of plastic deformation, metallurgical change, thermal distribution, and fluid flow. Numerical simulation is critical for successful design of the process and to understand the interaction among the numerous process parameters to control the press hardening process in order to consistently achieve desired part properties. Until now there has been no integratedmore » commercial software solution that can efficiently model the complete process from forming of the blank, heat transfer between the blank and tool, microstructure evolution in the blank, heat loss from tool to the fluid that flows through water channels in the tools. In this study, a numerical solution based on Altair HyperWorks® product suite involving RADIOSS®, a non-linear finite element based structural analysis solver and AcuSolve®, an incompressible fluid flow solver based on Galerkin Least Square Finite Element Method have been utilized to develop an efficient solution for complete press hardening process design and analysis. RADIOSS is used to handle the plastic deformation, heat transfer between the blank and tool, and microstructure evolution in the blank during cooling. While AcuSolve is used to efficiently model heat loss from tool to the fluid that flows through water channels in the tools. The approach is demonstrated through some case studies.« less

Numerical simulation of X90 UOE pipe forming process

NASA Astrophysics Data System (ADS)

Zou, Tianxia; Ren, Qiang; Peng, Yinghong; Li, Dayong; Tang, Ding; Han, Jianzeng; Li, Xinwen; Wang, Xiaoxiu

2013-12-01

The UOE process is an important technique to manufacture large-diameter welding pipes which are increasingly applied in oil pipelines and offshore platforms. The forming process of UOE mainly consists of five successive operations: crimping, U-forming, O-forming, welding and mechanical expansion, through which a blank is formed into a pipe in a UOE pipe mill. The blank with an appropriate edge bevel is bent into a cylindrical shape by crimping (C-forming), U-forming and O-forming successively. After the O-forming, there is an open-seam between two ends of the plate. Then, the blank is welded by automatic four-electrode submerged arc welding technique. Subsequently, the welded pipe is expanded with a mechanical expander to get a high precision circular shape. The multiple operations in the UOE mill make it difficult to control the quality of the formed pipe. Therefore, process design mainly relies on experience in practical production. In this study, the UOE forming of an API X90 pipe is studied by using finite element simulation. The mechanical properties tests are performed on the API X90 pipeline steel blank. A two-dimensional finite element model under the hypothesis of plane strain condition is developed to simulate the UOE process according to data coming from the workshop. A kinematic hardening model is used in the simulation to take the Bauschinger effect into account. The deformation characteristics of the blank during the forming processes are analyzed. The simulation results show a significant coherence in the geometric configurations comparing with the practical manufacturing.

Experimental and Numerical Investigations of Constraint Effect on Deformation Behavior of Tailor-Welded Blanks

NASA Astrophysics Data System (ADS)

Li, Yanhua; Lin, Jianping

2015-08-01

Tailor-welded blanks (TWBs) have been considered as a productive sheet forming method in automotive industries. However, formability of TWBs is reduced due to different properties or thicknesses of the blanks and is a challenge for manufacturing designers. The plastic capacity of TWBs is decreased even when the material and thickness are the same. The constraint effect of the laser weld (including weld and heat-affected zone) material in the forming process of similar TWBs is a key problem to be solved in the research, development and application of thin-sheet TWBs. In this paper, uniaxial tensile tests with full-field strain measurement by digital image correlation and Erichsen tests are performed to investigate the constraint effect on deformation behavior and explore the mechanism of decreasing formability of similar TWBs. In addition, finite element models are conducted under ABAQUS code to further reveal the phenomenal behavior of the constraint effect. The results of the base material and welded blanks are compared for characterizing the differences. Furthermore, in order to better understand this mechanism, theoretical and numerical investigations are employed and compared to interpret the constraint effect of laser weld on the deformation behavior of TWBs. An index is proposed to quantify the constraint effect. Results show that the constraint effect of laser weld appears in both stretch forming and drawing of TWBs. Strain paths are approaching the plane strain condition as compared to the monolithic blank due to the constraint effect. Constraint effect is a major factor affecting the formability of TWBs when the failure occurs away from the weld seam.

Testing glueline continuity in standard-size hardwood blanks by mechanical methods

Treesearch

David W. Patterson; Nathan D. Hesterman; Charles Gatchell

1991-01-01

Glueline continuity is very critical in standard-size hardwood blanks because the blanks are cut up into small furniture parts, and a small gap in the glueline of a blank may extend across the whole part—or a gap may appear as a crack in the final product. Strength is not a critical factor. The objective of this study was to determine if a gap in a glueline can be...

Seeing Red and Shooting Blanks: A Study of Red Quasars And Blank Field X-Ray Sources

NASA Technical Reports Server (NTRS)

Oliversen, Ronald J. (Technical Monitor); Elvis, Martin

2003-01-01

The primary source catalog of 'blanks' (bright ROSAT sources with no optical counterparts) has been published in the Astrophysical Journal. The first follow-up paper has also been published. This paper used a combination of ROSAT, Chandra and ground based data to convincingly identify one of the blanks as a Ultra-luminous X-ray source (ULX) in a spiral galaxy. A paper detailing optical and near-IR imaging observations of the remaining sources is underway.

Updated study reporting levels (SRLs) for trace-element data collected for the California Groundwater Ambient Monitoring and Assessment (GAMA) Priority Basin Project, October 2009-March 2013

USGS Publications Warehouse

Davis, Tracy A.; Olsen, Lisa D.; Fram, Miranda S.; Belitz, Kenneth

2014-01-01

Groundwater samples have been collected in California as part of statewide investigations of groundwater quality conducted by the U.S. Geological Survey for the Groundwater Ambient Monitoring and Assessment (GAMA) Priority Basin Project (PBP). The GAMA-PBP is being conducted in cooperation with the California State Water Resources Control Board to assess and monitor the quality of groundwater resources used for drinking-water supply and to improve public knowledge of groundwater quality in California. Quality-control samples (source-solution blanks, equipment blanks, and field blanks) were collected in order to ensure the quality of the groundwater sample results. Olsen and others (2010) previously determined study reporting levels (SRLs) for trace-element results based primarily on field blanks collected in California from May 2004 through January 2008. SRLs are raised reporting levels used to reduce the likelihood of reporting false detections attributable to contamination bias. The purpose of this report is to identify any changes in the frequency and concentrations of detections in field blanks since the last evaluation and update the SRLs for more recent data accordingly. Constituents analyzed were aluminum (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), lithium (Li), manganese (Mn), molybdenum (Mo), nickel (Ni), selenium (Se), silver (Ag), strontium (Sr), thallium (Tl), tungsten (W), uranium (U), vanadium (V), and zinc (Zn). Data from 179 field blanks and equipment blanks collected from March 2006 through March 2013 by the GAMA-PBP indicated that for trace elements that had a change in detection frequency and concentration since the previous review, the shift occurred near October 2009, in conjunction with a change in the capsule filters used by the study. Results for 89 field blanks and equipment blanks collected from October 2009 through March 2013 were evaluated for potential contamination bias by using the same approach developed by Olsen and others (2010). Some data collected by the National Water-Quality Assessment (NAWQA) Program for the Southern California Coastal Drainages study unit were included to supplement the GAMA-PBP data. The detection frequency and upper threshold of potential contamination bias (BD-90/90) were determined from field-blank and equipment-blank data for each trace element. The BD-90/90 is the 90th percentile concentration of potential extrinsic contamination calculated by using the binomial probability distribution for greater than 90 percent confidence. Additionally, data from laboratory blanks and blind blanks analyzed by the National Water Quality Laboratory (NWQL) during water years 2010 through 2013, and compiled by the USGS Branch of Quality Systems (BQS), were considered for each trace element. These results were compared to each constituent’s reporting level to determine whether an SRL was necessary to minimize the potential for detections in the groundwater samples, attributed principally to contamination bias. Results of the evaluation were used to set SRLs for trace-element data for about 1,135 samples of groundwater collected by the GAMA-PBP between October 2009 and March 2013. Ten trace elements analyzed (Sb, As, Be, B, Cd, Li, Se, Ag, Tl, and U) had blank results that did not necessitate establishing SRLs during this review or the review by Olsen and others (2010). Five trace elements analyzed (Al, Ba, Cr, Sr, and V) had blank results that necessitated establishing an SRL during the previous review but did not need an SRL starting October 2009. One trace element (Fe) had field and laboratory-blank results that necessitated keeping the previous SRL (6 micrograms per liter [μg/L]). Two trace elements (Ni and W) had quality-control results that warranted decreasing the previous SRL, and five trace elements (Cu, Pb, Mn, Mo, and Zn) had field, laboratory, or blind blank results that warranted establishing an SRL for the first time or increasing the previous SRL. SRLs for Cu (2.1 μg/L), Pb (0.82 μg/L), Mn (0.66 μg/L), Mo (0.023 μg/L), Ni (0.21 μg/L), W (0.023 μg/L), and Zn (6.2 μg/L) were changed to these levels starting October 2009, based on the BD-90/90 concentration for field blanks or the 99th percentile concentration for laboratory or blind blanks. The SRL for Fe was maintained at 6 μg/L, based on the minimum laboratory reporting level for iron. SRLs for these eight constituents were at least an order of magnitude below the regulatory benchmarks established for drinking water for health and aesthetic purposes; therefore, the practice of reporting concentrations below the SRLs as less than or equal to (≤) the measured value would not prevent the identification of values greater than the drinking-water benchmarks. Co was detected in 99 percent of field blanks, and with a BD-90/90 concentration of 0.38 μg/L, all groundwater results starting October 2009 were coded as “reviewed and rejected.” Co does not currently have a regulatory benchmark for drinking water. The primary sources of contamination for trace elements inferred from this review are the equipment or processes used in the field to collect the samples or in the laboratory. In particular, contamination in field blanks of Co and Mn was attributed to the high-capacity 0.45-micrometer pore-size capsule filters that were in regular use beginning in October 2009 by several USGS programs, including the GAMA-PBP and NAWQA Program, for filtering samples for analysis of trace elements. The SRLs determined in this report are intended to be used for GAMA groundwater-quality data for samples collected October 2009 through March 2013, or for as long as quality-control data indicate contamination similar to what was observed in this report; quality-control data should be continuously reviewed and SRLs re-assessed on at least a study-unit basis.

The information gained from witnesses' responses to an initial "blank" lineup.

PubMed

Palmer, Matthew A; Brewer, Neil; Weber, Nathan

2012-10-01

Wells ("The psychology of lineup identifications," Journal of Applied Social Psychology, 1984, 14, 89-103) proposed that a blank lineup (an initial lineup of known-to-be-innocent foils) can be used to screen eyewitnesses; witnesses who chose from a blank lineup (initial choosers) were more likely to make an error on a second lineup that contained a suspect than were witnesses who rejected a blank lineup (initial nonchoosers). Recent technological advances (e.g., computer-administered lineups) may overcome many of the practical difficulties cited as a barrier to the use of blank lineups. Our research extended knowledge about the blank lineup procedure by investigating the underlying causes of the difference in identification performance between initial choosers and initial nonchoosers. Studies 1a and 1b (total, N = 303) demonstrated that initial choosers were more likely to reject a second lineup than initial nonchoosers and witnesses who did not view a blank lineup, implying that cognitive biases (e.g., confirmation bias and commitment effects) influenced initial choosers' identification decisions. In Study 2 (N = 200), responses on a forced-choice identification test provided evidence that initial choosers have, on average, poorer memories for the culprit than do initial nonchoosers. We also investigated the usefulness of blank lineups for interpreting identification evidence. Diagnosticity ratios suggested that suspect identifications made by initial nonchoosers (cf. initial choosers) should have a greater impact on estimates of the likely guilt of the suspect. Furthermore, for initial nonchoosers, higher confidence in blank lineup rejections was associated with higher diagnosticity for subsequent suspect identifications. These results have implications for policy to guide the collection and interpretation of identification evidence. PsycINFO Database Record (c) 2012 APA, all rights reserved.

Piezoelectric resonator assembly with thin molybdenum mounting clips

DOEpatents

Peters, R. Donald

1981-01-01

A resonator mounting assembly wherein the resonator blank is mounted agai an essentially planar surface presented by a plurality of peripherally disposed mounting clips and bonded to this surface to provide substantially all the mechanical support for the blank in a direction normal to the major faces of the resonator blank, while being flexible in the directions parallel to said major faces so as to minimize radial stresses on the resonator blank, particularly during thermal cycling of the resonator assembly. The clips are fabricated of a low thermal expansion material, such as molybdenum, which also has considerable yield strength after exposure to processing temperatures; the bonding of the clips to the edges of the resonator blank can be achieved by a polyimide containing electrically conductive particles.

Influence of preconsolidation on consolidation quality after stamp forming of C/PEEK composites

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L.; Grouve, W. J. B.; Akkerman, R.

2016-10-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. Currently, expensive autoclave and press consolidation are used to preconsolidate blanks. This study investigates the influence of preconsolidation on final consolidation quality after stamp forming and explores the potential of alternative blank manufacturing methods that could reduce part costs. Blanks were manufactured using various blank manufacturing methods and subsequently were stamp formed. The consolidation quality both before and after stamp forming was compared, where the focus was on void content as the main measure for consolidation quality. The void content was characterized through thickness and density measurements, as well as by microscopy analysis. Results indicate that preconsolidation quality does have an influence on the final consolidation quality. This is due to the severe deconsolidation and limited reconsolidation during stamp forming. Nevertheless, the potential of automated fiber placement and ultrasonic spot welding as alternative blank manufacturing methods was demonstrated.

National Security And Institutional Pathologies: A Path Dependent Analysis Of U.S. Interventions In Iran, Guatemala, Cuba, And Iraq

DTIC Science & Technology

2016-09-01

The period of investigation for the expanded case study centers on the Eisenhower administration, but also addresses factors that occurred immediately...Understanding how institutional path dependent factors converged in each of these cases may shed light on how to prevent such foreign policy missteps in the...converged in each of these cases may shed light on how to prevent such foreign policy missteps in the future. vi THIS PAGE INTENTIONALLY LEFT BLANK

Tensile and creep rupture properties of (16) uncoated and (2) coated engineering alloys at elevated temperatures

NASA Technical Reports Server (NTRS)

Fritz, L. J.; Koster, W. P.

1977-01-01

Sixteen test materials were supplied by NASA-Lewis Research Center as wrought bar or cast remelt stock. The cast remelt stock was cast into test blanks with two such materials being also evaluated after Jocoat coating was applied. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, creep properties and creep rupture strength. Tests were conducted at temperatures applicable to the service temperature of the various alloys. This range extended from room temperature to 1000 C.

Accuracy of trace element determinations in alternate fuels

NASA Technical Reports Server (NTRS)

Greenbauer-Seng, L. A.

1980-01-01

A review of the techniques used at Lewis Research Center (LeRC) in trace metals analysis is presented, including the results of Atomic Absorption Spectrometry and DC Arc Emission Spectrometry of blank levels and recovery experiments for several metals. The design of an Interlaboratory Study conducted by LeRC is presented. Several factors were investigated, including: laboratory, analytical technique, fuel type, concentration, and ashing additive. Conclusions drawn from the statistical analysis will help direct research efforts toward those areas most responsible for the poor interlaboratory analytical results.

A sheet metal forming simulation of automotive outer panels considering the behavior of air in die cavity

NASA Astrophysics Data System (ADS)

Choi, Kwang Yong; Kim, Yun Chang; Choi, Hee Kwan; Kang, Chul Ho; Kim, Heon Young

2013-12-01

During a sheet metal forming process of automotive outer panels, the air trapped between a blank sheet and a die tool can become highly compressed, ultimately influencing the blank deformation and the press force. To prevent this problem, vent holes are drilled into die tools and needs several tens to hundreds according to the model size. The design and the drilling of vent holes are based on expert's experience and try-out result and thus the process can be one of reasons increasing development cycle. Therefore the study on the size, the number, and the position of vent holes is demanded for reducing development cycle, but there is no simulation technology for analyzing forming defects, making numerical sheet metal forming process simulations that incorporate the fluid dynamics of air. This study presents a sheet metal forming simulation of automotive outer panels (a roof and a body side outer) that simultaneously simulates the behavior of air in a die cavity. Through CAE results, the effect of air behavior and vent holes to blank deformation was analyzed. For this study, the commercial software PAM-STAMP{trade mark, serif} and PAM-SAFE{trade mark, serif} was used.

The development of cardiac surgery in West Africa-the case of Ghana

PubMed Central

Edwin, Frank; Tettey, Mark; Aniteye, Ernest; Tamatey, Martin; Sereboe, Lawrence; Entsua-Mensah, Kow; Kotei, David; Baffoe-Gyan, Kofi

2011-01-01

West Africa is one of the poorest regions of the world. The sixteen nations listed by the United Nations in this sub-region have some of the lowest gross domestic products in the world. Health care infrastructure is deficient in most of these countries. Cardiac surgery, with its heavy financial outlay is unavailable in many West African countries. These facts notwithstanding, some West African countries have a proud history of open heart surgery not very well known even in African health care circles. Many African health care givers are under the erroneous impression that the cardiovascular surgical landscape of West Africa is blank. However, documented reports of open-heart surgery in Ghana dates as far back as 1964 when surface cooling was used by Ghanaian surgeons to close atrial septal defects. Ghana's National Cardiothoracic Center is still very active and is accredited by the West African College of Surgeons for the training of cardiothoracic surgeons. Reports from Nigeria indicate open-heart surgery taking place from 1974. Cote D'Ivoire had reported on its first 300 open-heart cases by 1983. Senegal reported open-heart surgery from 1995 and still runs an active center. Cameroon started out in 2009 with work done by an Italian group that ultimately aims to train indigenous surgeons to run the program. This review traces the development and current state of cardiothoracic surgery in West Africa with Ghana's National Cardiothoracic Center as the reference. It aims to dispel the notion that there are no major active cardiothoracic centers in the West African sub-region. PMID:22355425

3D finite element modelling of sheet metal blanking process

NASA Astrophysics Data System (ADS)

Bohdal, Lukasz; Kukielka, Leon; Chodor, Jaroslaw; Kulakowska, Agnieszka; Patyk, Radoslaw; Kaldunski, Pawel

2018-05-01

The shearing process such as the blanking of sheet metals has been used often to prepare workpieces for subsequent forming operations. The use of FEM simulation is increasing for investigation and optimizing the blanking process. In the current literature a blanking FEM simulations for the limited capability and large computational cost of the three dimensional (3D) analysis has been largely limited to two dimensional (2D) plane axis-symmetry problems. However, a significant progress in modelling which takes into account the influence of real material (e.g. microstructure of the material), physical and technological conditions can be obtained by using 3D numerical analysis methods in this area. The objective of this paper is to present 3D finite element analysis of the ductile fracture, strain distribution and stress in blanking process with the assumption geometrical and physical nonlinearities. The physical, mathematical and computer model of the process are elaborated. Dynamic effects, mechanical coupling, constitutive damage law and contact friction are taken into account. The application in ANSYS/LS-DYNA program is elaborated. The effect of the main process parameter a blanking clearance on the deformation of 1018 steel and quality of the blank's sheared edge is analyzed. The results of computer simulations can be used to forecasting quality of the final parts optimization.

Exploration Supply Chain Simulation

NASA Technical Reports Server (NTRS)

2008-01-01

The Exploration Supply Chain Simulation project was chartered by the NASA Exploration Systems Mission Directorate to develop a software tool, with proper data, to quantitatively analyze supply chains for future program planning. This tool is a discrete-event simulation that uses the basic supply chain concepts of planning, sourcing, making, delivering, and returning. This supply chain perspective is combined with other discrete or continuous simulation factors. Discrete resource events (such as launch or delivery reviews) are represented as organizational functional units. Continuous resources (such as civil service or contractor program functions) are defined as enabling functional units. Concepts of fixed and variable costs are included in the model to allow the discrete events to interact with cost calculations. The definition file is intrinsic to the model, but a blank start can be initiated at any time. The current definition file is an Orion Ares I crew launch vehicle. Parameters stretch from Kennedy Space Center across and into other program entities (Michaud Assembly Facility, Aliant Techsystems, Stennis Space Center, Johnson Space Center, etc.) though these will only gain detail as the file continues to evolve. The Orion Ares I file definition in the tool continues to evolve, and analysis from this tool is expected in 2008. This is the first application of such business-driven modeling to a NASA/government-- aerospace contractor endeavor.

X-ray mask fabrication advancements at the Microlithographic Mask Development Center

NASA Astrophysics Data System (ADS)

Kimmel, Kurt R.; Hughes, Patrick J.

1996-05-01

The Microlithographic Mask Development Center (MMD) was established as the X-ray mask manufacturing facility at the IBM Microelectronics Division semiconductor fabricator in Essex Junction, Vermont. This center, in operation for over two years, produces high yielding, defect-free X-ray masks for competitive logic and memory products at 250nm groundrules and below. The MMD is a complete mask facility that manufactures silicon membrane mask blanks in the NIST format and finished masks with electroplated gold X-ray absorber. Mask patterning, with dimensions as small as 180 nm, is accomplished using IBM-built variable shaped spot e-beam systems. Masks are routinely inspected and repaired using state-of-the-art equipment: two KLA SEM Specs for defect inspection, a Leica LMS 2000 for image placement characterization, an Amray 2040c for image dimension characterization and a Micrion 8000 XMR for defect repair. This facility maintains a baseline mask process with daily production of 250nm, 32Mb SRAM line monitor masks for the continuous improvement of mask quality and processes. Development masks are produced for several semiconductor manufacturers including IBM, Motorola, Loral, and Sanders. Masks for 64Mb and 256Mb DRAM (IBM) and advanced logic/SRAM (IBM and Motorola) designs have also been delivered. This paper describes the MMD facility and its technical capabilities. Key manufacturing metrics such as mask turnaround time, parametric yield learning and defect reduction activities are highlighted. The challenges associated with improved mask quality, sub-180nm mask fabrication, and the transition to refractory metal absorber are discussed.

Spherical primary optical telescope (SPOT) segments

NASA Astrophysics Data System (ADS)

Hall, Christopher; Hagopian, John; DeMarco, Michael

2012-09-01

The spherical primary optical telescope (SPOT) project is an internal research and development program at NASA Goddard Space Flight Center. The goals of the program are to develop a robust and cost effective way to manufacture spherical mirror segments and demonstrate a new wavefront sensing approach for continuous phasing across the segmented primary. This paper focuses on the fabrication of the mirror segments. Significant cost savings were achieved through the design, since it allowed the mirror segments to be cast rather than machined from a glass blank. Casting was followed by conventional figuring at Goddard Space Flight Center. After polishing, the mirror segments were mounted to their composite assemblies. QED Technologies used magnetorheological finishing (MRF®) for the final figuring. The MRF process polished the mirrors while they were mounted to their composite assemblies. Each assembly included several magnetic invar plugs that extended to within an inch of the face of the mirror. As part of this project, the interaction between the MRF magnetic field and invar plugs was evaluated. By properly selecting the polishing conditions, MRF was able to significantly improve the figure of the mounted segments. The final MRF figuring demonstrates that mirrors, in the mounted configuration, can be polished and tested to specification. There are significant process capability advantes due to polishing and testing the optics in their final, end-use assembled state.

Cost-effective masks for deep x-ray lithography

NASA Astrophysics Data System (ADS)

Scheunemann, Heinz-Ulrich; Loechel, Bernd; Jian, Linke; Schondelmaier, Daniel; Desta, Yohannes M.; Goettert, Jost

2003-04-01

The production of X-ray masks is one of the key techniques for X-ray lithography and the LIGA process. Different ways for the fabrication of X-ray masks has been established. Very sophisticated, difficult and expensive procedures are required to produce high precision and high quality X-ray masks. In order to minimize the cost of an X-ray mask, the mask blank must be inexpensive and readily available. The steps involved in the fabrication process must also be minimal. In the past, thin membranes made of titanium, silicon carbide, silicon nitride (2-5μm) or thick beryllium substrates (500μm) have been used as mask blanks. Thin titanium and silicon compounds have very high transparency for X-rays; therefore, these materials are predestined for use as mask membrane material. However, the handling and fabrication of thin membranes is very difficult, thus expensive. Beryllium is highly transparent to X-rays, but the processing and use of beryllium is risky due to potential toxicity. During the past few years graphite based X-ray masks have been in use at various research centers, but the sidewall quality of the generated resist patterns is in the range of 200-300 nm Ra. We used polished graphite to improve the sidewall roughness, but polished graphite causes other problems in the fabrication of X-ray masks. This paper describes the advantages associated with the use of polished graphite as mask blank as well as the fabrication process for this low cost X-ray mask. Alternative membrane materials will also be discussed.

Observations of the atmosphere and surface state over Terra Nova Bay, Antarctica using unmanned aircraft systems

NASA Astrophysics Data System (ADS)

Cassano, J. J.; Seefeldt, M. W.; Palo, S.; Knuth, S. L.; Bradley, A. C.; Herrman, P. D.; Kernebone, P. A.; Logan, N. J.

2015-12-01

In September 2012 five Aerosonde unmanned aircraft were used to make measurements of the atmospheric state over the Terra Nova Bay polynya, Antarctica, to explore the details of air - sea ice - ocean coupling. A total of 14 flights were completed in September 2012. Ten of the flight missions consisted of two unmanned aircraft systems (UAS) sampling the atmosphere over Terra Nova Bay on five different days, with one UAS focusing on the downwind evolution of the air mass and a second UAS flying transects roughly perpendicular to the low level winds. The data from these coordinated UAS flights provide a comprehensive three-dimensional data set of the atmospheric state (air temperature, humidity, pressure, and wind) and surface skin temperature over Terra Nova Bay. The remaining UAS flights during the September 2012 field campaign included two local flights near McMurdo Station for flight testing, a single UAS flight to Terra Nova Bay, and a single UAS flight over the Ross Ice Shelf and Ross Sea polynya. A dataset containing the atmospheric and surface data as well as operational aircraft data has been submitted to the United States Antarctic Program Data Coordination Center (USAP-DCC, http://www.usap-data.org/) for free access (http://gcmd.nasa.gov/getdif.htm?NSF-ANT10-43657, doi:10.15784/600125).

47 CFR 73.646 - Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal. 73.646 Section 73.646 Telecommunication FEDERAL COMMUNICATIONS....646 Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal. (a...

Review of Trace-Element Field-Blank Data Collected for the California Groundwater Ambient Monitoring and Assessment (GAMA) Program, May 2004-January 2008

USGS Publications Warehouse

Olsen, Lisa D.; Fram, Miranda S.; Belitz, Kenneth

2010-01-01

Trace-element quality-control samples (for example, source-solution blanks, field blanks, and field replicates) were collected as part of a statewide investigation of groundwater quality in California, known as the Priority Basins Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basins Project is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB) to assess and monitor the quality of groundwater resources used for drinking-water supply and to improve public knowledge of groundwater quality in California. Trace-element field blanks were collected to evaluate potential bias in the corresponding environmental data. Bias in the environmental data could result from contamination in the field during sample collection, from the groundwater coming into contact with contaminants on equipment surfaces or from other sources, or from processing, shipping, or analyzing the samples. Bias affects the interpretation of environmental data, particularly if any constituents are present solely as a result of extrinsic contamination that would have otherwise been absent from the groundwater that was sampled. Field blanks were collected, analyzed, and reviewed to identify and quantify extrinsic contamination bias. Data derived from source-solution blanks and laboratory quality-control samples also were considered in evaluating potential contamination bias. Eighty-six field-blank samples collected from May 2004 to January 2008 were analyzed for the concentrations of 25 trace elements. Results from these field blanks were used to interpret the data for the 816 samples of untreated groundwater collected over the same period. Constituents analyzed were aluminum (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), boron (B), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), iron (Fe), lead (Pb), lithium (Li), manganese (Mn), mercury (Hg), molybdenum (Mo), nickel (Ni), selenium (Se), silver (Ag), strontium (Sr), thallium (Tl), tungsten (W), uranium (U), vanadium (V), and zinc (Zn). The detection frequency and the 90th percentile concentration at greater than 90 percent confidence were determined from the field-blank data for each trace element, and these results were compared to each constituent's long-term method detection level (LT-MDL) to determine whether a study reporting level (SRL) was necessary to ensure that no more than 10 percent of the detections in groundwater samples could be attributed solely to contamination bias. Only two of the trace elements analyzed, Li and Se, had zero detections in the 86 field blanks. Ten other trace elements (Sb, As, Be, B, Cd, Co, Mo, Ag, Tl, and U) were detected in fewer than 5 percent of the field blanks. The field-blank results for these constituents did not necessitate establishing SRLs. Of the 13 constituents that were detected in more than 5 percent of the field blanks, six (Al, Ba, Cr, Mn, Hg, and V) had field-blank results that indicated a need for SRLs that were at or below the highest laboratory reporting levels (LRL) used during the sampling period; these SRLs were needed for concentrations between the LT-MDLs and LRLs. The other seven constituents with detection frequencies above 5 percent (Cu, Fe, Pb, Ni, Sr, W, and Zn) had field-blank results that necessitated SRLs greater than the highest LRLs used during the study period. SRLs for these seven constituents, each set at the 90th percentile of their concentrations in the field blanks, were at least an order of magnitude below the regulatory thresholds established for drinking water for health or aesthetic purposes; therefore, reporting values below the SRLs as less than or equal to (=) the measured value would not prevent the identification of values greater than the drinking-water thresholds. The SRLs and drinking-water thresholds, respectively, for these 7 trace elements are Cu (1.7 ?g/L and 1,300

High Thermal Conductivity and High Wear Resistance Tool Steels for cost-effective Hot Stamping Tools

NASA Astrophysics Data System (ADS)

Valls, I.; Hamasaiid, A.; Padré, A.

2017-09-01

In hot stamping/press hardening, in addition to its shaping function, the tool controls the cycle time, the quality of the stamped components through determining the cooling rate of the stamped blank, the production costs and the feasibility frontier for stamping a given component. During the stamping, heat is extracted from the stamped blank and transported through the tool to the cooling medium in the cooling lines. Hence, the tools’ thermal properties determine the cooling rate of the blank, the heat transport mechanism, stamping times and temperature distribution. The tool’s surface resistance to adhesive and abrasive wear is also an important cost factor, as it determines the tool durability and maintenance costs. Wear is influenced by many tool material parameters, such as the microstructure, composition, hardness level and distribution of strengthening phases, as well as the tool’s working temperature. A decade ago, Rovalma developed a hot work tool steel for hot stamping that features a thermal conductivity of more than double that of any conventional hot work tool steel. Since that time, many complimentary grades have been developed in order to provide tailored material solutions as a function of the production volume, degree of blank cooling and wear resistance requirements, tool geometries, tool manufacturing method, type and thickness of the blank material, etc. Recently, Rovalma has developed a new generation of high thermal conductivity, high wear resistance tool steel grades that enable the manufacture of cost effective tools for hot stamping to increase process productivity and reduce tool manufacturing costs and lead times. Both of these novel grades feature high wear resistance and high thermal conductivity to enhance tool durability and cut cycle times in the production process of hot stamped components. Furthermore, one of these new grades reduces tool manufacturing costs through low tool material cost and hardening through readily available gas-quenching, whereas the other new grade enables a faster manufacturing of the tool at reduced cost by eliminating the time and money consuming high temperature hardening altogether. The latter newly developed grade can be hardened from a soft delivery state for easy machining to 52 HRc by way of a simple low temperature precipitation hardening. In this work, these new grades and the role of the tool material’s thermal, mechanical and tribological properties as well as their processing features will be discussed in light of enabling the manufacture of intelligent hot stamping tools.

Three-dimensional characterization of extreme ultraviolet mask blank defects by interference contrast photoemission electron microscopy.

PubMed

Lin, Jingquan; Weber, Nils; Escher, Matthias; Maul, Jochen; Han, Hak-Seung; Merkel, Michael; Wurm, Stefan; Schönhense, Gerd; Kleineberg, Ulf

2008-09-29

A photoemission electron microscope based on a new contrast mechanism "interference contrast" is applied to characterize extreme ultraviolet lithography mask blank defects. Inspection results show that positioning of interference destructive condition (node of standing wave field) on surface of multilayer in the local region of a phase defect is necessary to obtain best visibility of the defect on mask blank. A comparative experiment reveals superiority of the interference contrast photoemission electron microscope (Extreme UV illumination) over a topographic contrast one (UV illumination with Hg discharge lamp) in detecting extreme ultraviolet mask blank phase defects. A depth-resolved detection of a mask blank defect, either by measuring anti-node peak shift in the EUV-PEEM image under varying inspection wavelength condition or by counting interference fringes with a fixed illumination wavelength, is discussed.

Method for forming a liquid cooled airfoil for a gas turbine

DOEpatents

Grondahl, Clayton M.; Willmott, Leo C.; Muth, Myron C.

1981-01-01

A method for forming a liquid cooled airfoil for a gas turbine is disclosed. A plurality of holes are formed at spaced locations in an oversized airfoil blank. A pre-formed composite liquid coolant tube is bonded into each of the holes. The composite tube includes an inner member formed of an anti-corrosive material and an outer member formed of a material exhibiting a high degree of thermal conductivity. After the coolant tubes have been bonded to the airfoil blank, the airfoil blank is machined to a desired shape, such that a portion of the outer member of each of the composite tubes is contiguous with the outer surface of the machined airfoil blank. Finally, an external skin is bonded to the exposed outer surface of both the machined airfoil blank and the composite tubes.

Ultra-low level plutonium isotopes in the NIST SRM 4355A (Peruvian Soil-1).

PubMed

Inn, Kenneth G W; LaRosa, Jerome; Nour, Svetlana; Brooks, George; LaMont, Steve; Steiner, Rob; Williams, Ross; Patton, Brad; Bostick, Debbie; Eiden, Gregory; Petersen, Steve; Douglas, Matthew; Beals, Donna; Cadieux, James; Hall, Greg; Goldberg, Steve; Vogt, Stephan

2009-05-01

For more than 20 years, countries and their agencies which monitor radionuclide discharge sites and storage facilities have relied on the National Institute of Standards and Technology (NIST) Standard Reference Material (SRM) 4355 Peruvian Soil. Its low fallout contamination makes it an ideal soil blank for measurements associated with terrestrial-pathway-to-man studies. Presently, SRM 4355 is out of stock, and a new batch of the Peruvian soil is currently under development as future NIST SRM 4355A. Both environmental radioanalytical laboratories and mass spectrometry communities will benefit from the use of this SRM. The former must assess their laboratory procedural contamination and measurement detection limits by measurement of blank sample material. The Peruvian Soil is so low in anthropogenic radionuclide content that it is a suitable virtual blank. On the other hand, mass spectrometric laboratories have high sensitivity instruments that are capable of quantitative isotopic measurements at low plutonium levels in the SRM 4355 (first Peruvian Soil SRM) that provided the mass spectrometric community with the calibration, quality control, and testing material needed for methods development and legal defensibility. The quantification of the ultra-low plutonium content in the SRM 4355A was a considerable challenge for the mass spectrometric laboratories. Careful blank control and correction, isobaric interferences, instrument stability, peak assessment, and detection assessment were necessary. Furthermore, a systematic statistical evaluation of the measurement results and considerable discussions with the mass spectroscopy metrologists were needed to derive the certified values and uncertainties. The one sided upper limit of the 95% tolerance with 95% confidence for the massic (239)Pu content in SRM 4355A is estimated to be 54,000 atoms/g.

Seeing Red and Shooting Blanks: Study of Red Quasars and Blank X-Ray Sources

NASA Technical Reports Server (NTRS)

Oliversen, Ronald (Technical Monitor); Elvis, Martin

2005-01-01

A major paper describing the technique and providing a list of 'blanks' was published in the Astrophysical Journal (abstract below). The results revealed a fascinating trove of novel X-ray sources: high redshift clusters of galaxies found efficiently; X-ray absorbed, optically clean AGN, which may be the bright prototypes of Chandra Deep Survey sources; and several with a still unknown nature. Recent XMM-Newton results confirm the existence of this class of X-ray source with much refined positions. During the first year of this project we have made a major discovery. The second 'blanks' X-ray source observed with Chandra was found to be extended. Using Chandra data and ground-based R and K band imaging we estimated this to be a high redshift cluster of galaxies with z approx. 0.85. Spectroscopy agrees with this estimate (z=0.89). This success shows that our method of hunting down 'blank' field X-ray sources is a highly efficient method of finding the otherwise elusive high redshift clusters. With extensive follow-up we should be able to use 'blanks' to make cosmological tests. The paper is now in press in the Astrophysical Journal (abstract below.) The other Chandra source is point-like, showing that there are a variety of 'blank' source types. Other follow-up observations with XMM-Newton, and (newly approved in cycle 2) with Chandra are eagerly awaited. A follow-up paper uses a large amount of supporting data for the remaining blanks. A combination of ROSAT, Chandra and ground based data convincingly identified one of the blanks as a Ultra-luminous X-ray source (ULX) in a spiral galaxy (abstract below). This program resulted in 3 refereed papers in major journals, 4 conference proceedings and a significant fraction of the PhD thesis of Dr. Ilaria Cagnoni. Details of the publications are given.

Seeing Red and Shooting Blanks: A Study of Red Quasars and Blank Field X-Ray Sources

NASA Technical Reports Server (NTRS)

Elvis, Martin; Oliversen, Ronald J. (Technical Monitor)

2002-01-01

We have identified a population of 'blank field sources' (or 'blanks') among the ROSAT (Roentgen Satellite) bright unidentified X-ray sources with faint optical counterparts. The extreme X-ray over optical flux ratio of blank field sources is not compatible with the main classes of X-ray emitters except for extreme BL Lacertae objects at fx/fv is equal to or less than 35. From the analysis of ROSAT archival data we found evidence for only three sources, out of 16, needing absorption in excess of the Galactic value and no indication of variability. We also found evidence for an extended nature for only one of the five blanks with a serendipitous HRI (High Resolution Imager) detection; this source (1WGA J1226.9+3332) was confirmed as a z=0.89 cluster of galaxies. Palomar images reveal the presence of a red (O - E is equal to or greater than 2) counterpart in the X-ray error circle for six blanks. The identification process brought to the discovery of another high z cluster of galaxies, one (possibly extreme) BL Lac and two apparently normal type 1 AGNs (Active Galactic Nuclei). These AGNs, together with four more AGN-like objects seem to form a well defined group: they present type 1 X-ray spectra but red Palomar counterparts. We discuss the possible explanations for the discrepancy between the X-ray and optical data, among which: a suppressed big blue bump emission, an extreme dust to gas (approximately 40 - 60 the Galactic ratio) ratio value and a high redshift (z is greater than or equal to 3.5) QSO (Quasi-Stellar Object) nature. These AGN-like blanks seem to be the bright (and easier to study) analogs of the sources which are being found in deep Chandra observations. Five more blanks have a still an unknown nature.

Flight dynamics system software development environment (FDS/SDE) tutorial

NASA Technical Reports Server (NTRS)

Buell, John; Myers, Philip

1986-01-01

A sample development scenario using the Flight Dynamics System Software Development Environment (FDS/SDE) is presented. The SDE uses a menu-driven, fill-in-the-blanks format that provides online help at all steps, thus eliminating lengthy training and allowing immediate use of this new software development tool.

When the Ostrich-Algorithm Fails: Blanking Method Affects Spike Train Statistics.

PubMed

Joseph, Kevin; Mottaghi, Soheil; Christ, Olaf; Feuerstein, Thomas J; Hofmann, Ulrich G

2018-01-01

Modern electroceuticals are bound to employ the usage of electrical high frequency (130-180 Hz) stimulation carried out under closed loop control, most prominent in the case of movement disorders. However, particular challenges are faced when electrical recordings of neuronal tissue are carried out during high frequency electrical stimulation, both in-vivo and in-vitro . This stimulation produces undesired artifacts and can render the recorded signal only partially useful. The extent of these artifacts is often reduced by temporarily grounding the recording input during stimulation pulses. In the following study, we quantify the effects of this method, "blanking," on the spike count and spike train statistics. Starting from a theoretical standpoint, we calculate a loss in the absolute number of action potentials, depending on: width of the blanking window, frequency of stimulation, and intrinsic neuronal activity. These calculations were then corroborated by actual high signal to noise ratio (SNR) single cell recordings. We state that, for clinically relevant frequencies of 130 Hz (used for movement disorders) and realistic blanking windows of 2 ms, up to 27% of actual existing spikes are lost. We strongly advice cautioned use of the blanking method when spike rate quantification is attempted. Blanking (artifact removal by temporarily grounding input), depending on recording parameters, can lead to significant spike loss. Very careful use of blanking circuits is advised.

When the Ostrich-Algorithm Fails: Blanking Method Affects Spike Train Statistics

PubMed Central

Joseph, Kevin; Mottaghi, Soheil; Christ, Olaf; Feuerstein, Thomas J.; Hofmann, Ulrich G.

2018-01-01

Modern electroceuticals are bound to employ the usage of electrical high frequency (130–180 Hz) stimulation carried out under closed loop control, most prominent in the case of movement disorders. However, particular challenges are faced when electrical recordings of neuronal tissue are carried out during high frequency electrical stimulation, both in-vivo and in-vitro. This stimulation produces undesired artifacts and can render the recorded signal only partially useful. The extent of these artifacts is often reduced by temporarily grounding the recording input during stimulation pulses. In the following study, we quantify the effects of this method, “blanking,” on the spike count and spike train statistics. Starting from a theoretical standpoint, we calculate a loss in the absolute number of action potentials, depending on: width of the blanking window, frequency of stimulation, and intrinsic neuronal activity. These calculations were then corroborated by actual high signal to noise ratio (SNR) single cell recordings. We state that, for clinically relevant frequencies of 130 Hz (used for movement disorders) and realistic blanking windows of 2 ms, up to 27% of actual existing spikes are lost. We strongly advice cautioned use of the blanking method when spike rate quantification is attempted. Impact statement Blanking (artifact removal by temporarily grounding input), depending on recording parameters, can lead to significant spike loss. Very careful use of blanking circuits is advised. PMID:29780301

Low-Cost Opportunity for Small-Scale Manufacture of Hardwood Blanks

Treesearch

Bruce G. Hansen; Philip A. Araman

1985-01-01

We analyzed the manufacture of standard-size hardwood blanks from lumber on a relatively small scale by conventional processing. Requiring an investment of just over $200,000, the conventional mill can process 500 M bf (thousand board feet) of kiln-dried lumber annually. The study focused on the economics associated with manufacture of blanks from four species -...

76 FR 14697 - Aleris Blanking and Rim Products, Inc., a Division of Aleris International, Inc., Terre Haute, IN...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-17

... Products, Inc., a Division of Aleris International, Inc., Terre Haute, IN; Notice of Revised Determination... workers of Aleris Blanking and Rim Products, Inc., a division of Aleris International, Inc., Terre Haute... Blanking and Rim Products, Inc., a division of Aleris International, Inc., Terre Haute, Indiana, who became...

[Protection and bidirectional effect of rhubarb anthraquinone and tannins for rats' liver].

PubMed

Qin, Lu-shan; Zhao, Hai-ping; Zhao, Yan-ling; Ma, Zhi-jiel; Zeng, Ling-na; Zhang, Ya-ming; Zhang, Ping; Yan, Dan; Bai, Zhao-fang; Li, Yue; Hao, Qing-xiu; Zhao, Kui-jun; Wang, Jia-bo; Xiao, Xiao-he

2014-06-01

To compare the bidirectional effect of rhubarb total anthraquinone (TA) and total tannins (TT) on rats' liver. One hundred rats were randomly divided into 10 groups, i.e., the blank group, the model group, the blank + high dose TA group, the blank +low dose TA group, the blank + high dose TT group, the blank + low dose TT group, the model + high dose TA group, the model + low dose TA group, the model +high dose TT group, and the model + low dose TT group, 10 in each group. The carbon tetrachloride (CCI4) was used to prepare the acute liver injury rat model. TA and TT of rhubarb (at 5.40 g crude drugs/kg and 14.69 g crude drugs/kg) were intragastrically administrated to rats in all groups except the blank group and the model group, once daily for 6 successive days.The general state of rats, biochemical indices such as alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), laminin (LN), hyaluronic acid (HA), transforming growth factor beta1 (TGF-beta1), as well pathological results of rat liver tissues. Finally the protection laws of TA and TT for rats' liver were analyzed using factor analysis. Compared with the blank control group, all biochemical indices increased in the blank group (P < 0.05, P < 0.01). HA also increased in the blank + high dose TA group; AST, ALT, and HA also increased in the blank +high dose TT group (P < 0.05). Compared with the model group, AST, ALT, ALP, HA, and TGF-beta1 significantly decreased in the model + low dose TA group, the model + high dose TA group, the model + low dose TT group (P < 0.05, P < 0.01). Serum AST, ALT, and ALP also decreased in the model + high dose TT group (P < 0.05, P < 0.01). Pathological results showed that mild swollen liver cells in the model + high dose TA group. Fatty degeneration and fragmental necrosis around the central veins occurred in the blank + high dose TA group. The pathological injury was inproved in the model +low dose TA group. Two common factors, liver fibrosis and liver cell injury, were extracted by using factor analysis. TA showed stronger improvement of the two common factors than TT. Rhubarb TA and TT showed protective and harmful effects on rats' liver. At an equivalent dosage, TA had better liver protection than TT. High dose TT played a role in liver injury to some extent.

Blanking and piercing theory, applications and recent experimental results

NASA Astrophysics Data System (ADS)

Zaid, Adnan l. O.

2014-06-01

Blanking and piercing are manufacturing processes by which certain geometrical shapes are sheared off a sheet metal. If the sheared off part is the one required, the processes referred to as blanking and if the remaining part in the sheet is the one required, the process is referred to as piercing. In this paper, the theory and practice of these processes are reviewed and discussed The main parameters affecting these processes are presented and discussed. These include: the radial clearance percentage, punch and die geometrical parameters, for example punch and die profile radii. The abovementioned parameters on the force and energy required to effect blanking together with their effect on the quality of the products are also presented and discussed. Recent experimental results together with photomacrographs and photomicrographs are also included and discussed. Finally, the effect of punch and die wear on the quality of the blanks is alsogiven and discussed.

Microarray based on autodisplayed Ro proteins for medical diagnosis of systemic lupus erythematosus (SLE).

PubMed

Yoo, Gu; Bong, Ji-Hong; Kim, Sinyoung; Jose, Joachim; Pyun, Jae-Chul

2014-07-15

A microarray-based immunoassay for the detection of autoantibodies against Ro protein was developed using Escherichia coli with autodisplayed Ro proteins (Ro(+)-E. coli). Patient serum usually contains various antibodies against the outer membrane components of E. coli as well as autoantibodies against the Ro protein. Therefore, the conventional immunoassay based on Ro(+)-E. coli requires both wild type E. coli (blank test) and Ro(+)-E. coli, and both strains of E. coli must be prepared in situ for each individual test serum. In this study, we tested the feasibility of using several types of animal sera as a replacement for individual human sera. An immunoassay without the blank test was developed using Ro(+)-E. coli by (1) blocking with rabbit serum, and (2) cleaving the Fc region from antibodies using papain. Modified E. coli with autodisplayed Ro protein was immobilized to a surface-modified microplate and the applicability of the immunoassay without the blank test was demonstrated using sera from patients with systemic lupus erythematosus (SLE). Using this approach, a microarray-based fluorescence immunoassay with immobilized Ro(+)-E. coli was able to detect anti-Ro autoantibodies in SLE patient sera with high specificity and selectivity and improved efficiency. Copyright © 2014 Elsevier B.V. All rights reserved.

A genetic algorithm used for solving one optimization problem

NASA Astrophysics Data System (ADS)

Shipacheva, E. N.; Petunin, A. A.; Berezin, I. M.

2017-12-01

A problem of minimizing the length of the blank run for a cutting tool during cutting of sheet materials into shaped blanks is discussed. This problem arises during the preparation of control programs for computerized numerical control (CNC) machines. A discrete model of the problem is analogous in setting to the generalized travelling salesman problem with limitations in the form of precursor conditions determined by the technological features of cutting. A certain variant of a genetic algorithm for solving this problem is described. The effect of the parameters of the developed algorithm on the solution result for the problem with limitations is investigated.

Installation Restoration Program. Phase 2. Confirmation/Quantification. Stage 1 for United States Air Force Plant Number 59, Johnson City, New York. Appendices

DTIC Science & Technology

1988-03-01

AFP 59 SW-4 Production Field Blank Water Well Water Hart 004 Water Hart 005 f Hart 007 H.3-13 PRINCETON TESTING LABORATORYI 3v~ zANA -YS--S REDO:’- =I...observations. Enforcing the "buddy system" where appropriate. " Determining and posting locations and routes to medical facili- ties, including...poison control centers; arranging for emergency transportation to medical facilities. " Notifying local public emergency officers, i.e., police and fire

Excavated Soils Management Plan for AOCs 44 and 52, Fort Devens

DTIC Science & Technology

1994-05-01

I FORT DEVENS AOCs 44 AND 52 I I I FINAL EXCAVATED SOILS MANAGEMENT PLAN DATA ITEM A009I I U 20070424310 I CONTRACT DAAA15-91-D-0008 I U.S. ARMY...obselete FINAL EXCAVATED SOILS MANAGEMENT PLAN FOR AOCs 44 AND 52 FORT DEVENS Prepared for. U.S. Army Enviromnental Center Aberdeen Proving Ground, Maryland...BLANK 3 I I I I I I I I I I FINAL EXCAVATED SOILS MANAGEMENT PLAN FOR AOCs 44 AND 52 FORT DEVENS TABLE OF CONTENTS 1 Section Title Page No. 1.0

Production of the 4.1-m Zerodur mirror blank for the VISTA Telescope

NASA Astrophysics Data System (ADS)

Doehring, Thorsten; Jedamzik, Ralf; Wittmer, Volker; Thomas, Armin

2004-09-01

VISTA (Visible and Infrared Survey Telescope for Astronomy) is designed to be the world's largest wide field telescope. After finishing of the construction the telescope will be part of ESO and located in Chile close to the VLT observatory at Cerro Paranal. In November 2001 SCHOTT was selected by the VISTA project office at the Royal Observatory of Edinburgh to deliver the 4.1 m diameter primary mirror blank. The manufacturing of the mirror blank made from the zero expansion material Zerodur was challenging especially due to the f/1 design. Several tons of the glass ceramic material were removed during the grinding operation. A meniscus blank with a diameter of 4100 mm and a thickness of 171.5 mm was generated, having a large central hole of 1200 mm and an aspherical shape of the concave surface. Also the handling and turning operations needed special effort and were performed by a skilled team. This paper presents details and pictures of the corresponding production and inspection sequence at SCHOTT. The geometrical parameters were measured during manufacturing by help of a laser tracker system and the achieved parameters were compared with the initial technical specification. The final quality inspection verified the excellent quality of the mirror blank. The close co-operation between the astronomers and industry resulted in a project management without problems. In April 2003 the VISTA blank was delivered successfully within a ceremony dedicated to the anniversary of "100 years of astronomical mirror blanks from SCHOTT."

The Muslim Brotherhood and Modern Education: How Will the Muslim Brotherhood Address Egypt’s Failing Education System?

DTIC Science & Technology

2012-09-01

Thesis Advisor: Robert Springborg Second Reader: Mohammed M. Hafez THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form...of secular subjects. vi THIS PAGE INTENTIONALLY LEFT BLANK vii TABLE OF CONTENTS I . INTRODUCTION...understanding, this thesis would not have been possible. xii THIS PAGE INTENTIONALLY LEFT BLANK 1 I . INTRODUCTION A. MAJOR RESEARCH QUESTION The

Exploring Valued-Added Options - Edge-Glued Panels and Blanks Offer Value-Added Opportunities

Treesearch

Bob Smith; Philip A. Araman

1997-01-01

As sawmills search for new opportunities to add value to rough sawn lumber, many consider producing dimension parts as one solution. Assembling dimension parts into edge-glued panels or standard blanks can add even further value. Blanks are defined as pieces of solid wood (which may be edge-glued) that are manufactured to a predetermined size. This article discusses...

Penetrating ocular trauma associated with blank cartridge

PubMed Central

2014-01-01

Background Blank cartridge guns are generally regarded as being harmless and relative safe. However recent published articles demonstrated that the gas pressure from the exploding propellant of blank cartridge is powerful enough to penetrate the thoracic wall, abdominal muscle, small intestine and the skull. And there has been a limited number of case reports of ocular trauma associated with blank cartridge injury. In addition, no report on case with split extraocular muscle injury with traumatic cataract and penetrating corneoscleral wound associated with blank cartridge has been previously documented. This report describes the case of patient who sustained penetrating ocular injury with extraocular muscle injury by a close-distance blank cartridge that required surgical intervention. Case presentation A 20-year-old man sustained a penetrating globe injury in the right eye while cleaning a blank cartridge pistol. His uncorrected visual acuity at presentation was hand motion and he had a flame burn of his right upper and lower lid with multiple missile wounds. On slit-lamp examination, there was a 12-mm laceration of conjunctiva along the 9 o'clock position with two pinhole-like penetrating injuries of cornea and sclera. There was also a 3-mm corneal laceration between 9 o'clock and 12 o'clock and the exposed lateral rectus muscle was split. Severe Descemet's membrane folding with stromal edema was observed, and numerous yellow, powder-like foreign bodies were impacted in the cornea. Layered anterior chamber bleeding with traumatic cataract was also noted. Transverse view of ultrasonography showed hyperechoic foreign bodies with mild reduplication echoes and shadowing. However, a computed tomographic scan using thin section did not reveal a radiopaque foreign body within the right globe. Conclusion To our best knowledge, this is the first case report of split extraocular muscle injury with traumatic cataract and penetrating ocular injury caused by blank cartridge injury. Intraocular foreign bodies undetectable by CT were identified by B-scan ultrasonography in our patient. This case highlights the importance of additional ultrasonography when evaluating severe ocular trauma. And ophthalmologists should consider the possibility of penetrating injury caused by blank ammunition. PMID:24589340

Design calculations for a xenon plasma x-ray shield to protect the NIF optical Thomson scattering diagnostic

NASA Astrophysics Data System (ADS)

Swadling, G. F.; Ross, J. S.; Datte, P.; Moody, J.; Divol, L.; Jones, O.; Landen, O.

2016-11-01

An Optical Thomson Scattering (OTS) diagnostic is currently being developed for the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. This diagnostic is designed to make measurements of the hohlraum plasma parameters, such as the electron temperature and the density, during inertial confinement fusion (ICF) experiments. NIF ICF experiments present a very challenging environment for optical measurements; by their very nature, hohlraums produce intense soft x-ray emission, which can cause "blanking" (radiation induced opacity) of the radiation facing optical components. The soft x-ray fluence at the surface of the OTS blast shield, 60 cm from the hohlraum, is estimated to be ˜8 J cm-2. This is significantly above the expected threshold for the onset of "blanking" effects. A novel xenon plasma x-ray shield is proposed to protect the blast shield from x-rays and mitigate "blanking." Estimates suggest that an areal density of 1019 cm-2 Xe atoms will be sufficient to absorb 99.5% of the soft x-ray flux. Two potential designs for this shield are presented.

Design calculations for a xenon plasma x-ray shield to protect the NIF optical Thomson scattering diagnostic.

PubMed

Swadling, G F; Ross, J S; Datte, P; Moody, J; Divol, L; Jones, O; Landen, O

2016-11-01

An Optical Thomson Scattering (OTS) diagnostic is currently being developed for the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory. This diagnostic is designed to make measurements of the hohlraum plasma parameters, such as the electron temperature and the density, during inertial confinement fusion (ICF) experiments. NIF ICF experiments present a very challenging environment for optical measurements; by their very nature, hohlraums produce intense soft x-ray emission, which can cause "blanking" (radiation induced opacity) of the radiation facing optical components. The soft x-ray fluence at the surface of the OTS blast shield, 60 cm from the hohlraum, is estimated to be ∼8 J cm -2 . This is significantly above the expected threshold for the onset of "blanking" effects. A novel xenon plasma x-ray shield is proposed to protect the blast shield from x-rays and mitigate "blanking." Estimates suggest that an areal density of 10 19 cm -2 Xe atoms will be sufficient to absorb 99.5% of the soft x-ray flux. Two potential designs for this shield are presented.

Different Spectrophotometric Methods for Simultaneous Determination of Trelagliptin and Its Acid Degradation Product

PubMed Central

Hassan, Mostafa A.; Zaghary, Wafaa A.

2018-01-01

New spectrophotometric and chemometric methods were carried out for the simultaneous assay of trelagliptin (TRG) and its acid degradation product (TAD) and applied successfully as a stability indicating assay to recently approved Zafatek® tablets. TAD was monitored using TLC to ensure complete degradation. Furthermore, HPLC was used to confirm dealing with one major acid degradation product. The proposed methods were developed by manipulating zero-order, first-derivative, and ratio spectra of TRG and TAD using simultaneous equation, first-derivative, and mean-centering methods, respectively. Using Spectra Manager II and Minitab v.14 software, the absorbance at 274 nm–260.4 nm, amplitudes at 260.4 nm–274.0 nm, and mean-centered values at 287.6 nm–257.2 nm were measured against methanol as a blank for TRG and TAD, respectively. Linearity and the other validation parameters were acceptable at concentration ranges of 5–50 μg/mL and 2.5–25 μg/mL for TRG and TAD, respectively. Using one-way analysis of variance (ANOVA), the optimized methods were compared and proved to be accurate for the simultaneous assay of TRG and TAD. PMID:29629213

Different Spectrophotometric Methods for Simultaneous Determination of Trelagliptin and Its Acid Degradation Product.

PubMed

Mowaka, Shereen; Ayoub, Bassam M; Hassan, Mostafa A; Zaghary, Wafaa A

2018-01-01

New spectrophotometric and chemometric methods were carried out for the simultaneous assay of trelagliptin (TRG) and its acid degradation product (TAD) and applied successfully as a stability indicating assay to recently approved Zafatek® tablets. TAD was monitored using TLC to ensure complete degradation. Furthermore, HPLC was used to confirm dealing with one major acid degradation product. The proposed methods were developed by manipulating zero-order, first-derivative, and ratio spectra of TRG and TAD using simultaneous equation, first-derivative, and mean-centering methods, respectively. Using Spectra Manager II and Minitab v.14 software, the absorbance at 274 nm-260.4 nm, amplitudes at 260.4 nm-274.0 nm, and mean-centered values at 287.6 nm-257.2 nm were measured against methanol as a blank for TRG and TAD, respectively. Linearity and the other validation parameters were acceptable at concentration ranges of 5-50  μ g/mL and 2.5-25  μ g/mL for TRG and TAD, respectively. Using one-way analysis of variance (ANOVA), the optimized methods were compared and proved to be accurate for the simultaneous assay of TRG and TAD.

High speed reflectometer for EUV mask-blanks

NASA Astrophysics Data System (ADS)

Wies, Christian; Lebert, Rainer; Jagle, Bernhard; Juschkin, L.; Sobel, F.; Seitz, H.; Walter, Ronny; Laubis, C.; Scholze, F.; Biel, W.; Steffens, O.

2005-06-01

AIXUV GmbH and partners have developed a high speed Reflectometer for EUV mask-blanks which is fully compliant with the SEMI-standard P38 for EUV-mask-blank metrology. The system has been installed in June 2004 at SCHOTT Lithotec AG. It features high throughput, high lateral and spectral resolution, high reproducibility and low absolute uncertainty. Using AIXUV's EUV-LAMP and debris mitigation, low cost-of-ownership and high availability is expected. The spectral reflectance of up to 3 mask-blanks per hour can be measured with at least 20 spots each. The system is push button-controlled. Results are stored in CSV file format. For a spot size of 0.1x1 mm2, 2000 spectral channels of 1.6 pm bandwidth are recorded from 11.6 nm to 14.8 nm. The reflectance measurement is based on the comparison of the sample under test to two reference mirrors calibrated at the PTB radiometry laboratory at BESSY II. The three reflection spectra are recorded simultaneously. For each spot more than 107 photons are accumulated in about 20 s, providing statistical reproducibility below 0.2% RMS. The total uncertainty is below 0.5% absolute. Wavelength calibration better than 1 pm RMS over the whole spectral range is achieved by reference to NIST published wavelengths of about 100 xenon emission lines. It is consistent with the wavelength of the krypton 3d-5p absorption resonance at 13.5947 nm to better than 2 pm.

High speed reflectometer for EUV mask-blanks

NASA Astrophysics Data System (ADS)

Wies, C.; Lebert, R.; Jaegle, B.; Juschkin, L.; Sobel, F.; Seitz, H.; Walter, R.; Laubis, C.; Scholze, F.; Biel, W.; Steffens, O.

2005-05-01

AIXUV GmbH and partners have developed a high speed Reflectometer for EUV mask-blanks which is fully compliant with the SEMI-standard P38 for EUV-mask-blank metrology. The system has been installed in June 2004 at SCHOTT Lithotec AG. It features high throughput, high lateral and spectral resolution, high reproduci-bility and low absolute uncertainty. Using AIXUV's EUV-LAMP and debris mitigation, low cost-of-ownership and high availability is expected. The spectral reflectance of up to 3 mask-blanks per hour can be measured with at least 20 spots each. The system is push button-controlled. Results are stored in CSV file format. For a spot size of 0.1×1 mm2, 2000 spectral chan-nels of 1.6 pm bandwidth are recorded from 11.6 nm to 14.8 nm. The reflectance measurement is based on the comparison of the sample under test to two reference mirrors calibrated at the PTB radiometry laboratory at BESSY II. The three reflection spectra are recorded simultaneously. For each spot more than 107 photons are ac-cumulated in about 20 s, providing statistical reproducibility below 0.2 % RMS. The total uncertainty is below 0.5 % absolute. Wavelength calibration better than 1 pm RMS over the whole spectral range is achieved by refe-rence to NIST published wavelengths of about 100 xenon emission lines. It is consistent with the wavelength of the krypton 3d-5p absorption resonance at 13.5947 nm to better than 2 pm.

Formation mechanism of the photomask blanks material related haze

NASA Astrophysics Data System (ADS)

Kim, Jung-Jin; Choi, Junyoul; Koh, Soowan; Kim, Minho; Lee, Jiyoung; Lee, Han-Shin; Kim, Byung Gook; Jeon, Chan-uk

2016-05-01

We have observed a new type haze of which formation deviates from the generally accepted models with respect to the size, shape, and removability by chemicals. It has very small size of 50~100nm and are crowded around the cell boundary, while the typical haze doesn't prefer a special region on mask in the majority of cases. It is hard to remove by general cleaning, while the typical haze is easily removed by general cleaning process and even de-ionized water. It is confirmed that the source of the haze is blank material related ions which are formed by chemical etching of blanks during mask cleaning process or the photomask blanks itself.

Improved confidence intervals when the sample is counted an integer times longer than the blank.

PubMed

Potter, William Edward; Strzelczyk, Jadwiga Jodi

2011-05-01

Past computer solutions for confidence intervals in paired counting are extended to the case where the ratio of the sample count time to the blank count time is taken to be an integer, IRR. Previously, confidence intervals have been named Neyman-Pearson confidence intervals; more correctly they should have been named Neyman confidence intervals or simply confidence intervals. The technique utilized mimics a technique used by Pearson and Hartley to tabulate confidence intervals for the expected value of the discrete Poisson and Binomial distributions. The blank count and the contribution of the sample to the gross count are assumed to be Poisson distributed. The expected value of the blank count, in the sample count time, is assumed known. The net count, OC, is taken to be the gross count minus the product of IRR with the blank count. The probability density function (PDF) for the net count can be determined in a straightforward manner.

Estimating surface hardening profile of blank for obtaining high drawing ratio in deep drawing process using FE analysis

NASA Astrophysics Data System (ADS)

Tan, C. J.; Aslian, A.; Honarvar, B.; Puborlaksono, J.; Yau, Y. H.; Chong, W. T.

2015-12-01

We constructed an FE axisymmetric model to simulate the effect of partially hardened blanks on increasing the limiting drawing ratio (LDR) of cylindrical cups. We partitioned an arc-shaped hard layer into the cross section of a DP590 blank. We assumed the mechanical property of the layer is equivalent to either DP980 or DP780. We verified the accuracy of the model by comparing the calculated LDR for DP590 with the one reported in the literature. The LDR for the partially hardened blank increased from 2.11 to 2.50 with a 1 mm depth of DP980 ring-shaped hard layer on the top surface of the blank. The position of the layer changed with drawing ratios. We proposed equations for estimating the inner and outer diameters of the layer, and tested its accuracy in the simulation. Although the outer diameters fitted in well with the estimated line, the inner diameters are slightly less than the estimated ones.

Lightweight ZERODUR mirror blanks: recent advances supporting faster, cheaper, and better spaceborne optical telescope assemblies

NASA Astrophysics Data System (ADS)

Hull, Tony; Westerhoff, Thomas

2014-10-01

While there is no single material solution ideal for all missions, recent advances by SCHOTT in fabricating lightweight mirror blanks makes ZERODUR® a highly viable solution for many spaceborne telescopes. ZERODUR® is a well-characterized very low-expansion material. Monolithic mirrors are made without bonding or fusing out of highly homogeneous and isotropic blanks currently available in sizes up to 4m plus. We will summarize results recently given in a series of papers on the characteristics of these lightweight mirror blanks in sizes from 0.3m up, and describe the method of blank fabrication, with its compatibility to contemporary optical fabrication techniques that control of all optical spatial frequencies. ZERODUR® has a 35 year heritage in space on numerous missions, including the secondary mirror of Hubble, and all the Chandra mirrors. With the lightweighting we will discuss, ZERODUR® is now a high performing, affordable and rapidly produced mirror substrate suitable for lightweight imaging telescopes.

Seal for fluid forming tools

DOEpatents

Golovashchenko, Sergey Fedorovich [Beverly Hills, MI; Bonnen, John Joseph Francis [Milford, MI

2012-03-20

An electro-hydraulic forming tool for forming a sheet metal blank in a one-sided die has first and second rigid rings that engage opposite sides of a sheet metal blank. The rigid rings are contained within slots on a die portion and a hydraulic force applicator portion of the forming tool. The seals are either resiliently biased by an elastomeric member or inherently resiliently biased into contact with the blank.

12 CFR Appendix A to Part 1024 - Instructions for Completing HUD-1 and HUD-1a Settlement Statements; Sample HUD-1 and HUD-1a...

Code of Federal Regulations, 2013 CFR

2013-01-01

... lines are provided in section L for any additional settlement charges. Blank lines are also provided for additional insertions in sections J and K. The names of the recipients of the settlement charges in section L... blank lines. Lines and columns in section J which relate to the Borrower's transaction may be left blank...

12 CFR Appendix A to Part 1024 - Instructions for Completing HUD-1 and HUD-1A Settlement Statements; Sample HUD-1 and HUD-1A...

Code of Federal Regulations, 2012 CFR

2012-01-01

... lines are provided in section L for any additional settlement charges. Blank lines are also provided for additional insertions in sections J and K. The names of the recipients of the settlement charges in section L... blank lines. Lines and columns in section J which relate to the Borrower's transaction may be left blank...

Blanks: a computer program for analyzing furniture rough-part needs in standard-size blanks

Treesearch

Philip A. Araman

1983-01-01

A computer program is described that allows a company to determine the number of edge-glued, standard-size blanks required to satisfy its rough-part needs for a given production period. Yield and cost information also is determined by the program. A list of the program inputs, outputs, and uses of outputs is described, and an example analysis with sample output is...

Blank and sample handling troubleshooting in ultratrace analysis of alkylphenols and bisphenol A by liquid chromatography tandem mass spectrometry.

PubMed

Salgueiro-González, N; Concha-Graña, E; Turnes-Carou, I; Muniategui-Lorenzo, S; López-Mahía, P; Prada-Rodríguez, D

2012-11-15

Blank contamination is a notorious problem in the ultratrace analysis of alkylphenols and bisphenol A. The achievement of low detection limits is complicated due to the high background signals. Furthermore, overestimations and underestimations in the analytical results can occur when blank levels are not stable. Thus, a review of sources of blank contamination in this type of analysis was carried out. Several sources of contamination were identified and useful guidelines are proposed for the determination of these compounds in water samples by liquid chromatography coupled with mass spectrometry. The system contamination was maintained below 0.09 ng (reagent blank) for all compounds and below 0.003 μg L(-1) (procedure blank). The main improvement was obtained by using LC-MS grade solvent in the mobile phase and PTFE syringe filters for the filtration of the sample extracts. Sample handling aspects such as filtration and storage of the water samples were also considered. The filtration of the samples should be avoided because both contamination and adsorption problems were observed when different kinds of filters were assayed. The refrigerated storage of water samples should be limited to 5 days (without addition of methanol) or 8 days (with 5% methanol). Copyright © 2012 Elsevier B.V. All rights reserved.

Large optical glass blanks for the ELT generation

NASA Astrophysics Data System (ADS)

Jedamzik, Ralf; Petzold, Uwe; Dietrich, Volker; Wittmer, Volker; Rexius, Olga

2016-07-01

The upcoming extremely large telescope projects like the E-ELT, TMT or GMT telescopes require not only large amount of mirror blank substrates but have also sophisticated instrument setups. Common instrument components are atmospheric dispersion correctors that compensate for the varying atmospheric path length depending on the telescope inclination angle. These elements consist usually of optical glass blanks that have to be large due to the increased size of the focal beam of the extremely large telescopes. SCHOTT has a long experience in producing and delivering large optical glass blanks for astronomical applications up to 1 m and in homogeneity grades up to H3 quality in the past. The most common optical glass available in large formats is SCHOTT N-BK7. But other glass types like F2 or LLF1 can also be produced in formats up to 1 m. The extremely large telescope projects partly demand atmospheric dispersion components even in sizes beyond 1m up to a range of 1.5 m diameter. The production of such large homogeneous optical glass banks requires tight control of all process steps. To cover this demand in the future SCHOTT initiated a research project to improve the large optical blank production process steps from melting to annealing and measurement. Large optical glass blanks are measured in several sub-apertures that cover the total clear aperture of the application. With SCHOTT's new stitching software it is now possible to combine individual sub-aperture measurements to a total homogeneity map of the blank. In this presentation first results will be demonstrated.

Developing Computer-Interactive Tape Exercises for Intermediate-Level Business French.

ERIC Educational Resources Information Center

Garnett, Mary Anne

One college language teacher developed computer-interactive audiotape exercises for an intermediate-level class in business French. The project was undertaken because of a need for appropriate materials at that level. The use of authoring software permitted development of a variety of activity types, including multiple-choice, fill-in-the-blank,…

Edge Length and Surface Area of a Blank: Experimental Assessment of Measures, Size Predictions and Utility

PubMed Central

Dogandžić, Tamara; Braun, David R.; McPherron, Shannon P.

2015-01-01

Blank size and form represent one of the main sources of variation in lithic assemblages. They reflect economic properties of blanks and factors such as efficiency and use life. These properties require reliable measures of size, namely edge length and surface area. These measures, however, are not easily captured with calipers. Most attempts to quantify these features employ estimates; however, the efficacy of these estimations for measuring critical features such as blank surface area and edge length has never been properly evaluated. In addition, these parameters are even more difficult to acquire for retouched implements as their original size and hence indication of their previous utility have been lost. It has been suggested, in controlled experimental conditions, that two platform variables, platform thickness and exterior platform angle, are crucial in determining blank size and shape meaning that knappers can control the interaction between size and efficiency by selecting specific core angles and controlling where fracture is initiated. The robustness of these models has rarely been tested and confirmed in context other than controlled experiments. In this paper, we evaluate which currently employed caliper measurement methods result in the highest accuracy of size estimations of blanks, and we evaluate how platform variables can be used to indirectly infer aspects of size on retouched artifacts. Furthermore, we investigate measures of different platform management strategies that control the shape and size of artifacts. To investigate these questions, we created an experimental lithic assemblage, we digitized images to calculate 2D surface area and edge length, which are used as a point of comparison for the caliper measurements and additional analyses. The analysis of aspects of size determinations and the utility of blanks contributes to our understanding of the technological strategies of prehistoric knappers and what economic decisions they made during process of blank production. PMID:26332773

Prediction of Supersonic Store Separation Characteristics Including Fuselage and Stores of Noncircular Cross Section. Volume III. Appendices A and B, Details of Program I.

DTIC Science & Technology

1980-11-01

IZPT,ITH,IDEL,NTAP7,IAR,IAN,IUB, IGB(7) ,IVB,IU,IV,IW,IVA,IWA, ICP, IPHI,IYB,NAG,NAP,NAV,NAS, NASHK, NAFLD ,IAO,IDO,ISKO,TYIMI,IZIM,ISVN,ISKP,NRING,IROW...locations in blank common required in SOLVE NASHIK maximum locations in blank common required in BSHOCK NAFLD maximum locations in blank common

Stacking and determination of phenazine-1-carboxylic acid with low pKa in soil via moving reaction boundary formed by alkaline and double acidic buffers in capillary electrophoresis.

PubMed

Sun, Chong; Yang, Xiao-Di; Fan, Liu-Yin; Zhang, Wei; Xu, Yu-Quan; Cao, Cheng-Xi

2011-04-01

As shown herein, a normal moving reaction boundary (MRB) formed by an alkaline buffer and a single acidic buffer had poor stacking to the new important plant growth promoter of phenazine-1-carboxylic acid (PCA) in soil due to the leak induced by its low pK(a). To stack the PCA with low pK(a) efficiently, a novel stacking system of MRB was developed, which was formed by an alkaline buffer and double acidic buffers (viz., acidic sample and blank buffers). With the novel system, the PCA leaking into the blank buffer from the sample buffer could be well stacked by the prolonged MRB formed between the alkaline buffer and blank buffer. The relevant mechanism of stacking was discussed briefly. The stacking system, coupled with sample pretreatment, could achieve a 214-fold increase of PCA sensitivity under the optimal conditions (15 mM (pH 11.5) Gly-NaOH as the alkaline buffer, 15 mM (pH 3.0) Gly-HCl-acetonitrile (20%, v/v) as the acidic sample buffer, 15 mM (pH 3.0) Gly-HCl as the blank buffer, 3 min 13 mbar injection of double acidic buffers, benzoic acid as the internal standard, 75 μm i.d. × 53 cm (44 cm effective length) capillary, 25 kV and 248 nm). The limit of detection of PCA in soil was decreased to 17 ng/g, the intra-day and inter-day precision values (expressed as relative standard deviations) were 3.17-4.24% and 4.17-4.87%, respectively, and the recoveries of PCA at three concentration levels changed from 52.20% to 102.61%. The developed method could be used for the detection of PCA in soil at trace level.

Radiocarbon Analysis of Individual Amino Acids: Carbon Blank Quantification for a Small-Sample High-Pressure Liquid Chromatography Purification Method.

PubMed

Bour, Amy L; Walker, Brett D; Broek, Taylor A B; McCarthy, Matthew D

2016-04-05

Compound-specific radiocarbon analysis (CSRA) of amino acids (AAs) is of great interest as a proxy for organic nitrogen (N) cycling rates, dating archeological bone collagen, and investigating processes shaping the biogeochemistry of global N reservoirs. However, recoverable quantities of individual compounds from natural samples are often insufficient for radiocarbon ((14)C) analyses (<50 μg C). Constraining procedural carbon (C) blanks and their isotopic contributions is critical for reporting of accurate CSRA measurements. Here, we report the first detailed quantification of C blanks (including sources, magnitudes, and variability) for a high-pressure liquid chromatography (HPLC) method designed to purify individual AAs from natural samples. We used pairs of AA standards with either modern (M) or dead (D) fraction modern (Fm) values to quantify MC and DC blanks within several chromatographic regions. Blanks were determined for both individual and mixed AA standard injections with peak loadings ranging from 10 to 85 μg C. We found 0.8 ± 0.4 μg of MC and 1.0 ± 0.5 μg of DC were introduced by downstream sample preparation (drying, combustion, and graphitization), which accounted for essentially the entire procedural blank for early eluting AAs. For late-eluting AAs, higher eluent organic content and fraction collected volumes contributed to total blanks of 1.5 ± 0.75 μg of MC and 3.0 ± 1.5 μg of DC. Our final measurement uncertainty for 20 μg of C of most AAs was ±0.02 Fm, although sample size requirements are larger for similar uncertainty in late-eluting AAs. These results demonstrate the first CSRA protocol for many protein AAs with uncertainties comparable to the lowest achieved in prior studies.

Inspection of lithographic mask blanks for defects

DOEpatents

Sommargren, Gary E.

2001-01-01

A visible light method for detecting sub-100 nm size defects on mask blanks used for lithography. By using optical heterodyne techniques, detection of the scattered light can be significantly enhanced as compared to standard intensity detection methods. The invention is useful in the inspection of super-polished surfaces for isolated surface defects or particulate contamination and in the inspection of lithographic mask or reticle blanks for surface defects or bulk defects or for surface particulate contamination.

Theoretical Analysis on Mechanical Deformation of Membrane-Based Photomask Blanks

NASA Astrophysics Data System (ADS)

Marumoto, Kenji; Aya, Sunao; Yabe, Hedeki; Okada, Tatsunori; Sumitani, Hiroaki

2012-04-01

Membrane-based photomask is used in proximity X-ray lithography including that in LIGA (Lithographie, Galvanoformung und Abformung) process, and near-field photolithography. In this article, out-of-plane deformation (OPD) and in-plane displacement (IPD) of membrane-based photomask blanks are theoretically analyzed to obtain the mask blanks with flat front surface and low stress absorber film. First, we derived the equations of OPD and IPD for the processing steps of membrane-based photomask such as film deposition, back-etching and bonding, using a theory of symmetrical bending of circular plates with a coaxial circular hole and that of deformation of cylinder under hydrostatic pressure. The validity of the equations was proved by comparing the calculation results with experimental ones. Using these equations, we investigated the relation between the geometry of the mask blanks and the distortions generally, and gave the criterion to attain the flat front surface. Moreover, the absorber stress-bias required to obtain zero-stress on finished mask blanks was also calculated and it has been found that only little stress-bias was required for adequate hole size of support plate.

Investigation of 2,4-dinitrophenylhydrazine impregnated adsorbent tubes for the collection of airborne aldehydes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holdren, M.W.; Smith, D.L.; Russell, N.K.

1988-06-01

The objective of the study was to investigate the use of 2,4-dinitrophenylhydrazine (DNPH) impregnated adsorbents for sampling airborne aldehydes. Experimental results using a 17 cu m environmental chamber and various spiked amounts of aldehyde material (low ppb levels) showed that the DNPH coated cartridge and the DNPH/acetonitrile impinger methods gave equivalent results. Blank levels of the DNPH-coated cartridges were studied as a function of storage time using various containers and temperature conditions. Canisters pressurized with zero-grade nitrogen provided the best storage device. Lower blank levels were also obtained when the cartridges were stored at lower temperatures. Blank levels appear tomore » equilibrate after six days of storage. To assure that quality data will be obtained, cartridges should be grouped according to batch number and blank levels should be determined prior to any field monitoring effort. Blank cartridge levels should be an order of magnitude lower than sample cartridge level. High performance liquid chromatography with UV detection proved to be a sensitive and stable analytical method for the DNPH derivatives.« less

Attentional Lapses in Attention-Deficit/Hyperactivity Disorder: Blank Rather Than Wandering Thoughts.

PubMed

Van den Driessche, Charlotte; Bastian, Mikaël; Peyre, Hugo; Stordeur, Coline; Acquaviva, Éric; Bahadori, Sara; Delorme, Richard; Sackur, Jérôme

2017-10-01

People with attention-deficit/hyperactivity disorder (ADHD) have difficulties sustaining their attention on external tasks. Such attentional lapses have often been characterized as the simple opposite of external sustained attention, but the different types of attentional lapses, and the subjective experiences to which they correspond, remain unspecified. In this study, we showed that unmedicated children (ages 6-12) with ADHD, when probed during a standard go/no-go task, reported more mind blanking (a mental state characterized by the absence of reportable content) than did control participants. This increase in mind blanking happened at the expense of both focused and wandering thoughts. We also found that methylphenidate reverted the level of mind blanking to baseline (i.e., the level of mind blanking reported by control children without ADHD). However, this restoration led to mind wandering more than to focused attention. In a second experiment, we extended these findings to adults who had subclinical ADHD. These results suggest that executive functions impaired in ADHD are required not only to sustain external attention but also to maintain an internal train of thought.

Hypothetical Case and Scenario Description for International Transportation of Spent Nuclear Fuel.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Adam David; Osborn, Douglas; Jones, Katherine A.

To support more rigorous analysis on global security issues at Sandia National Laboratories (SNL), there is a need to develop realistic data sets without using "real" data or identifying "real" vulnerabilities, hazards or geopolitically embarrassing shortcomings. In response, an interdisciplinary team led by subject matter experts in SNL's Center for Global Security and Cooperation (CGSC) developed a hypothetical case description. This hypothetical case description assigns various attributes related to international SNF transportation that are representative, illustrative and indicative of "real" characteristics of "real" countries. There is no intent to identify any particular country and any similarity with specific real-world eventsmore » is purely coincidental. To support the goal of this report to provide a case description (and set of scenarios of concern) for international SNF transportation inclusive of as much "real-world" complexity as possible -- without crossing over into politically sensitive or classified information -- this SAND report provides a subject matter expert-validated (and detailed) description of both technical and political influences on the international transportation of spent nuclear fuel. [PAGE INTENTIONALLY LEFT BLANK]« less

Prosthesis Material

NASA Technical Reports Server (NTRS)

1995-01-01

FAB/CAM, a subsidiary of the Harshberger Prosthetic and Orthotic Center, Inc., approached Marshall for help in replacing the heavy, fragile plaster they used to produce master molds for prosthetics. Concurrently, Marshall and Martin Marietta were creating a commercial derivative of the foam insulation used to protect the Space Shuttle External Tank from excessive heat. FAB/CAM found the foam blanks to be lighter, cheaper and easier to manufacture than plaster, resulting in lower costs to the consumer. Martin Marietta markets the foam system, MARCORE, for the prosthesis market. The system also has commercial potential in high temperature insulation and structural applications.

BLADED IMPELLER FOR TURBOBLOWERS

DOEpatents

Baumann, K.

1949-10-01

A means is given of holding open-sided impeller blades in a turbo-rotor. Two half blades, with dovetail roots of sufficient weight to contain the center of gravity, are fitted into slots cut in the rotor so as to form the desired angle between the blade faces. The adjoining edges of the half blades are welded to form one solid blade that is securely locked an the rotor. This design permits the manufacture of a V shaped impeller blade without the need of machining the entire V shaped contour from a single blank, and furthermore provides excellent locking characteristics for attachment to the rotor.

Seeing Red and Shooting Blanks: A Study of Red Quasars and Blank Field X-Ray Sources

NASA Technical Reports Server (NTRS)

Oliversen, Ronald J. (Technical Monitor); Elvis, Martin

2004-01-01

One type of "Blank Field X-ray Source" is now being seen in deep Chandra and XMM-Newton surveys. These are the newly dubbed "XBONGs" (X-ray Bright, Optically Normal Galaxies). The study of the brighter counterparts from ROSAT and XMM- Newton serendipitous surveys is therefore of renewed interest and topicality. We continue to define the properties of the ROSAT sample which is the basis of this grant. We expect to publish the SEDs of these sources soon.

Rapid iconic erasure without masking.

PubMed

Tijus, Charles Albert; Reeves, Adam

2004-01-01

We report on the erasure of the iconic memory of an array of 12 black letters flashed on a continuously- present white field. Erasure is accomplished by replacing the 16 ms letter array (frame 1) with a blank white frame for 16 ms (frame 2). The letter array returns in frame 3, with from one to six letters missing. Report of the missing letters is accurate without the blank white frame but is impoverished with it, as if interposing the blank erases the icon. Erasure occurs without any obvious luminance masking, 'mud splashes', pattern masking (backward, forward, or metacontrast), lateral masking, or masking by object substitution. Erasure is greatly decreased if the blank is presented one frame earlier or later. We speculate that erasure is due to a rapid reset of the icon produced by an informational mis-match.

Preliminary evaluation of new polymer matrix for solid-phase extraction of nonylphenol from water samples.

PubMed

Guerreiro, António; Soares, Ana; Piletska, Elena; Mattiasson, Bo; Piletsky, Sergey

2008-03-31

Molecularly imprinted (MIP) and blank polymers with affinity for nonylphenol were designed using computational modelling. Chromatographic tests demonstrated higher affinity of imprinted polymers towards the template nonylphenol as compared with blank polymers. The performance of both polymers in solid-phase extraction was however very similar. Both blank and imprinted polymers appeared to be suitable for the removal and pre-concentration of nonylphenol from contaminated water samples with 99% efficiency of the recovery. The commercial resins PH(EC) (Biotage) and C18 (Varian) tested in the same conditions used for comparative purposes had recovery rate <84%. The polymer capacity for nonylphenol was 231 mg g(-1) for blank and 228 mg g(-1) for MIP. The synthesised materials can have significance for sample pre-concentration and environmental analysis of this class of compounds.

Blank corrections for ramped pyrolysis radiocarbon dating of sedimentary and soil organic carbon.

PubMed

Fernandez, Alvaro; Santos, Guaciara M; Williams, Elizabeth K; Pendergraft, Matthew A; Vetter, Lael; Rosenheim, Brad E

2014-12-16

Ramped pyrolysis (RP) targets distinct components of soil and sedimentary organic carbon based on their thermochemical stabilities and allows the determination of the full spectrum of radiocarbon ((14)C) ages present in a soil or sediment sample. Extending the method into realms where more precise ages are needed or where smaller samples need to be measured involves better understanding of the blank contamination associated with the method. Here, we use a compiled data set of RP measurements of samples of known age to evaluate the mass of the carbon blank and its associated (14)C signature, and to assess the performance of the RP system. We estimate blank contamination during RP using two methods, the modern-dead and the isotope dilution method. Our results indicate that during one complete RP run samples are contaminated by 8.8 ± 4.4 μg (time-dependent) of modern carbon (MC, fM ∼ 1) and 4.1 ± 5.5 μg (time-independent) of dead carbon (DC, fM ∼ 0). We find that the modern-dead method provides more accurate estimates of uncertainties in blank contamination; therefore, the isotope dilution method should be used with caution when the variability of the blank is high. Additionally, we show that RP can routinely produce accurate (14)C dates with precisions ∼100 (14)C years for materials deposited in the last 10,000 years and ∼300 (14)C years for carbon with (14)C ages of up to 20,000 years.

U. S. and Soviet MHD Technology: A Comparative Overview

DTIC Science & Technology

1974-01-01

developments in magnetohydro- dynamic power generation, in which the Soviet program far exceeds the American« The USSR now operates the first MUD power...their respective development approaches, and compares major U.S. and USSR MHD facilities and national program objectives. Preceding page blank...devoted to the history of MHD develop - ment in these two countries, respective development approaches, and cur- rent status of individual programs

Autonomous Vehicles: A Policy Roadmap for Law Enforcement

DTIC Science & Technology

2015-09-01

Timeline for Autonomous Vehicle Development ................................48 Figure 3. RAS 2020 Strategic Theme, Five Areas of Strategic Activity to...BLANK 1 I. INTRODUCTION It would be like an elevator. They used to have elevator operators, and then we developed some simple circuitry to have...advancements to make autonomous vehicles possible are being developed , manufactured, and tested. These two advantages should be used to help develop a solid

Versioning System for Distributed Ontology Development

DTIC Science & Technology

2016-03-15

provides guidelines for evaluating the impact of the version changes. This page intentionally left blank. v...conformance to a clear set of development and versioning guidelines to assure that changes and extensions can be integrated back into the “main development... guidelines for evolution of an ontology would have considerably helped the users of the ontology in these situations. The currently accessible

Assessment of Hyporheic Zone, Flood-Plain, Soil-Gas, Soil, and Surface-Water Contamination at the McCoys Creek Chemical Training Area, Fort Gordon, Georgia, 2009-2010

USGS Publications Warehouse

Guimaraes, Wladmir B.; Falls, W. Fred; Caldwell, Andral W.; Ratliff, W. Hagan; Wellborn, John B.; Landmeyer, James E.

2011-01-01

The U.S. Geological Survey, in cooperation with the U.S. Department of the Army Environmental and Natural Resources Management Office of the U.S. Army Signal Center and Fort Gordon, Georgia, assessed the hyporheic zone, flood plain, soil gas, soil, and surface water for contaminants at the McCoys Creek Chemical Training Area (MCTA) at Fort Gordon, from October 2009 to September 2010. The assessment included the detection of organic contaminants in the hyporheic zone, flood plain, soil gas, and surface water. In addition, the organic contaminant assessment included the analysis of organic compounds classified as explosives and chemical agents in selected areas. Inorganic contaminants were assessed in soil and surface-water samples. The assessment was conducted to provide environmental contamination data to the U.S. Army at Fort Gordon pursuant to requirements of the Resource Conservation and Recovery Act Part B Hazardous Waste Permit process. Ten passive samplers were deployed in the hyporheic zone and flood plain, and total petroleum hydrocarbons (TPH) and octane were detected above the method detection level in every sampler. Other organic compounds detected above the method detection level in the hyporheic zone and flood-plain samplers were trichloroethylene, and cis- and trans- 1, 2-dichloroethylene. One trip blank detected TPH below the method detection level but above the nondetection level. The concentrations of TPH in the samplers were many times greater than the concentrations detected in the blank; therefore, all other TPH concentrations detected are considered to represent environmental conditions. Seventy-one soil-gas samplers were deployed in a grid pattern across the MCTA. Three trip blanks and three method blanks were used and not deployed, and TPH was detected above the method detection level in two trip blanks and one method blank. Detection of TPH was observed at all 71 samplers, but because TPH was detected in the trip and method blanks, TPH was censored and, therefore, only 7 of the 71 samplers were reported as detecting TPH. In addition, benzene, toluene, ethylbenzene, and total xylene were detected above the method detection level in 22 samplers. Other compounds detected above the method detection level included naphthalene, octane, undecane, tridecane, 1,2,4-trimethylbenzene, trichloroethylene, perchloroethylene, chloroform, and 1,4-dichlorobenzene. Subsequent to the soil-gas survey, five locations with elevated contaminant mass were selected and a passive sampler was deployed at those locations to detect the presence of organic compounds classified as explosives or chemical agents. No explosives or chemical agents were detected above the method detection level, but some compounds were detected below the method detection level but above the nondetection level. Dimethyl disulfide, benzothiazole, chloroacetophenones, and para-chlorophenyl methyl sulfide were all detected below the method detection level but above the nondetection level. The compounds 2,4-dinitrotoluene, and para-chlorophenyl methyl sulfone were detected in samplers but also were detected in trip blanks and are not considered as present in the MCTA. The same five locations that were selected for sampling of explosives and chemical agents were selected for soil sampling. Metal concentrations in composite soil samples collected at five locations from land surface to a depth of 6 inches did not exceed the U.S. Environmental Protection Agency Regional Screening Levels for Industrial Soil. Concentrations in some compounds were higher than the South Carolina Department of Health and Environmental Control background levels for nearby South Carolina, including aluminum, arsenic, barium, beryllium, chromium, copper, iron, lead, manganese, nickel, and potassium. A surface-water sample was collected from McCoys Creek and analyzed for volatile organic compounds, semivolatile organic compounds, and inorganic compounds (metals). No volatile organic compounds and (or) semivolatile organic compounds were detected at levels above the maximum contaminant level of the U.S. Environmental Protection Agency (USEPA) National Primary Drinking Water Standard, and no inorganic compounds exceeded the maximum contaminant level of the USEPA National Primary Drinking Water Standard or the Georgia In-Stream Water-Quality Standard. Iron was the only inorganic compound detected in the surface-water sample (578 micrograms per liter) that exceeded the USEPA National Secondary Drinking Water Standard of 300 micrograms per liter.

CTEPP NC DATA QA/QC RESULTS

EPA Science Inventory

This data set contains the method performance results. This includes field blanks, method blanks, duplicate samples, analytical duplicates, matrix spikes, and surrogate recovery standards.

The Children’s Total Exposure to Persistent Pesticides and Other Persistent Pollutant (...

Porous mandrels provide uniform deformation in hydrostatic powder metallurgy

NASA Technical Reports Server (NTRS)

Gripshover, P. J.; Hanes, H. D.

1967-01-01

Porous copper mandrels prevent uneven deformation of beryllium machining blanks. The beryllium powder is arranged around these mandrels and hot isostatically pressed to form the blanks. The mandrels are then removed by leaching.

76 FR 37063 - Marine Mammals; File No. 16510

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

... Blank Park Zoo [Kevin V. Drees, Responsible Party], 7401 SW. Ninth, Des Moines, IA 50315, has applied in... Vancouver Aquarium, Vancouver, Canada for purposes of public display at the Blank Park Zoo. The receiving...

In situ air temperature and humidity measurements over diverse land covers in Greenbelt, Maryland, November 2013-November 2015

NASA Astrophysics Data System (ADS)

Carroll, Mark L.; Brown, Molly E.; Wooten, Margaret R.; Donham, Joel E.; Hubbard, Alfred B.; Ridenhour, William B.

2016-09-01

As our climate changes through time there is an ever-increasing need to quantify how and where it is changing so that mitigation strategies can be implemented. Urban areas have a disproportionate amount of warming due, in part, to the conductive properties of concrete and asphalt surfaces, surface albedo, heat capacity, lack of water, etc. that make up an urban environment. The NASA Climate Adaptation Science Investigation working group at Goddard Space Flight Center in Greenbelt, MD, conducted a study to collect temperature and humidity data at 15 min intervals from 12 sites at the center. These sites represent the major surface types at the center: asphalt, building roof, grass field, forest, and rain garden. The data show a strong distinction in the thermal properties of these surfaces at the center and the difference between the average values for the center compared to a local meteorological station. The data have been submitted to Oak Ridge National Laboratory Distributed Active Archive Center (ORNL-DAAC) for archival in comma separated value (csv) file format (Carroll et al., 2016) and can be found by following this link: http://daac.ornl.gov/cgi-bin/dsviewer.pl?ds_id=1319.

What the Hell Do We Do Now? A Policy Options Analysis of State, Local, and Tribal Law Enforcement Participation in Immigration Enforcement

DTIC Science & Technology

2013-09-01

less like adversaries and more like partners with the affected communities in the effort. 94 THIS PAGE INTENTIONALLY LEFT BLANK 95 LIST OF... INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this collection of information is...ABSTRACT UU NSN 7540–01–280–5500 Standard Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved

Super-Resolution Algorithm in Cumulative Virtual Blanking

NASA Astrophysics Data System (ADS)

Montillet, J. P.; Meng, X.; Roberts, G. W.; Woolfson, M. S.

2008-11-01

The proliferation of mobile devices and the emergence of wireless location-based services have generated consumer demand for precise location. In this paper, the MUSIC super-resolution algorithm is applied to time delay estimation for positioning purposes in cellular networks. The goal is to position a Mobile Station with UMTS technology. The problem of Base-Stations herability is solved using Cumulative Virtual Blanking. A simple simulator is presented using DS-SS signal. The results show that MUSIC algorithm improves the time delay estimation in both the cases whether or not Cumulative Virtual Blanking was carried out.

Evaluation of attenuated PSM photomask blanks with TF11 chrome and FEP-171 resist on a 248 nm DUV laser pattern generator

NASA Astrophysics Data System (ADS)

Xing, Kezhao; Björnborg, Charles; Karlsson, Henrik; Paulsson, Adisa; Rosendahl, Anna; Beiming, Peter; Vedenpää, Jukka; Walford, Jonathan; Newman, Tom

2007-10-01

Tighter requirements on mask resolution, CD and image positioning accuracy at and beyond the 45 nm technology node push the development of improved photomask blanks. One such blank for attenuated phase-shift masks (att-PSM) provides a thinner chrome film, named TF11, with higher chrome etch rate compared to the previous generation Att- PSM blank (NTAR5 chrome film) from the same supplier. Reduced stress in the chrome film also results in less image placement error induced by the material. FEP-171 is the positive chemically amplified resist (PCAR) that is most commonly used in advanced mask manufacturing with both 50 keV variable shaped e-beam (VSB) and DUV laser pattern generators. TF11 allows an FEP-171 resist film down to about 2000 Å thickness with sufficient etch resistance, while the standard resist thickness for NTAR5 is around 3000 Å. This work has experimentally evaluated the use of TF11 chrome and FEP-171 resist together with a 248 nm DUV laser pattern generator, the Sigma7500. First, patterning performance in resist with thicknesses from 2000 Å to 2600 Å, in steps of 100 Å, was tested with respect to swing curve and basic lithographic parameters including resolution, CD linearity, CD iso-dense bias and dose sensitivity. Patterning results on mask showed a swing minimum at around 2200 Å and a swing maximum at around 2500 Å, which correspond to reflectivity measurements for 248 nm wavelength performed by the blank supplier. It was concluded that the overall patterning performance was best close to the swing maximum. Thereafter the patterning performance using TF11 at two resist thicknesses, 2000 Å and 2550 Å, was studied in more detail and compared to performance using NTAR5 with 3200 Å resist. The evaluation showed that the Sigma7500-II offers good compatibility with TF11, especially using the optimized FEP-171 resist thickness of 2550 Å. It also showed that the patterning capability of the Sigma7500-II using TF11 and 2550 Å resist is improved compared to using NTAR5 and 3200 Å resist.

Effects of Lugol staining on stenosis formation induced by radiofrequency ablation of esophageal squamous epithelium: a study in a porcine model.

PubMed

Schölvinck, D W; Alvarez Herrero, L; Visser, M; Bergman, J J G H M; Weusten, B L A M

2015-10-01

Preliminary data show higher stricture rates after radiofrequency ablation (RFA) for early esophageal squamous neoplasia compared with Barrett's esophagus. We studied the effects of Lugol stain (LS) directly prior to RFA on stricture formation in squamous epithelium. Of 16 pigs, the distal half of the esophagus was LS, followed by circumferential RFA (single application 12 J/cm(2) ) in the unstained and stained esophagus. Pigs were euthanized at day 0 (n = 4), 3 (n = 4), or 28 (n = 8). Histology was evaluated in four areas: blank-control (no RFA, no LS), blank-RFA (no LS), LS+RFA, and LS-control (no RFA). Stenosis severity in LS+RFA and blank-RFA at 28 days was assessed by the ratio of the mucosal diameter at the RFA area to the diameter 2 cm proximal of this zone. Histology showed submucosal edema in 50% of LS+RFA versus 0% in blank-RFA. Severity and depth of inflammation (day 3) was equal in LS+RFA and blank-RFA. Severity and depth of fibrosis (day 28) appeared more severe in LS+RFA. Consequently, stenosis was present in 100% (LS+RFA) versus 12.5% (blank-RFA). The stenosis-severity ratio was 0.40 (interquartile range 0.29-0.45) in LS+RFA versus 0.73 (interquartile range 0.64-0.78) in blank-RFA (P = 0.012). Limitations of this study were the difference in uptake of LS between pigs and humans, the difference in esophageal anatomy between pigs and humans, and between the proximal and distal esophagus within pigs. In conclusion, in the porcine squamous esophagus, stenosis rate and severity after RFA increased when preceded by LS. LS may be contributing in the altered response of squamous epithelium to RFA as compared with Barrett's esophagus. © 2014 International Society for Diseases of the Esophagus.

CTEPP-OH DATA QA/QC RESULTS

EPA Science Inventory

This data set contains the method performance results for CTEPP-OH. This includes field blanks, method blanks, duplicate samples, analytical duplicates, matrix spikes, and surrogate recovery standards.

The Children’s Total Exposure to Persistent Pesticides and Other Persisten...

Establishment of a New Zealand rabbit model of spinal tuberculosis.

PubMed

Geng, Guangqi; Wang, Qian; Shi, Jiandang; Yan, Junfa; Niu, Ningkui; Wang, Zili

2015-04-01

This was an experimental study. To investigate and evaluate the experimental method of establishing a New Zealand rabbit model of spinal tuberculosis. Establishing animal models of tuberculosis is critical to the experimental and clinical study of tuberculosis, especially spinal tuberculosis. However, the rapid spread of Mycobacterium tuberculosis and subsequent high mortality thwarted their effort. Since then, no animal models have been established of spinal tuberculosis. Forty-two New Zealand rabbits were randomly divided into experimental (n=20), control (n=20), and blank groups (n=2). Experimental animals were sensitized by complete Freund's adjuvant. A hole drilled under the upper endplate of the L4 vertebral body was filled with a gelfoam sponge infused with 0.1 mL H37Rv standard M. tuberculosis suspension (in controls, culture medium, and saline). Blank animals received no treatment. Survival 8 weeks after surgery was 89.5%, 94.7%, and 100% in experimental, control, and blank groups, respectively. The model was successfully established in all surviving experimental rabbits. In experimental animals, vertebral body destruction at 4 weeks was 50% by x-ray; 83.3% by computed tomography reconstruction and magnetic resonance imaging; at 8 weeks, 58.8% by x-ray and 100% by computed tomograph reconstruction and magnetic resonance imaging. At 8 weeks, experimental animals developed vertebral destruction, granulation, and necrosis and 17.6% had psoas abscess. Histopathology revealed numerous lymphocytes and epithelioid cells, trabecular bone fracture, and coagulative necrosis in the vertebrae of experimental animals; bacterium culture was 52.9% positive. Control and blank animals showed no such changes. A New Zealand rabbit of spinal tuberculosis model can be successfully established by drilling a hole in the upper endplate of the vertebral body, filling with gelfoam sponge infused with H37Rv standard M. tuberculosis suspension after sensitization by complete Freund's adjuvant.

Experimental and numerical investigation of dual phase steels formability during laser-assisted hole-flanging

NASA Astrophysics Data System (ADS)

Motaman, S. A. H.; Komerla, K.; Storms, T.; Prahl, U.; Brecher, C.; Bleck, W.

2018-05-01

Today, in the automotive industry dual phase (DP) steels are extensively used in the production of various structural parts due to their superior mechanical properties. Hole-flanging of such steels due to simultaneous bending and stretching of sheet metal, is complex and associated with some issues such as strain and strain rate localization, development of micro-cracks, inhomogeneous sheet thinning, etc. In this study an attempt is made to improve the formability of DP sheets, by localized Laser heating. The Laser beam was oscillated in circular pattern rapidly around the pre-hole, blanked prior to the flanging process. In order to investigate formability of DP steel (DP1000), several uniaxial tensile tests were conducted from quasi to intermediate strain rates at different temperatures in warm regime. Additionally, experimentally acquired temperature and strain rate-dependent flow curves were fed into thermomechanical finite element (FE) simulation of the hole-flanging process using the commercial FE software ABAQUS/Explicit. Several FE simulations were performed in order to evaluate the effect of blank's initial temperature and punch speed on deformation localization, stress evolution and temperature distribution in DP1000 sheets during warm hole-flanging process. The experimental and numerical analyses revealed that prescribing a distribution of initial temperature between 300 to 400 °C to the blank and setting a punch speed that accommodates strain rate range of 1 to 5 s-1 in the blank, provides the highest strain hardening capacity in the considered rate and temperature regimes for DP1000. This is in fact largely due to the dynamic strain aging (DSA) effect which occurs due to pinning of mobile dislocations by interstitial solute atoms, particularly at elevated temperatures.

A Preliminary Evaluation of Near-Transducer Velocities Collected with Low-Blank Acoustic Doppler Current Profiler

USGS Publications Warehouse

Gartner, J.W.; Ganju, N.K.; ,

2002-01-01

Many streams and rivers for which the US Geological Survey must provide discharge measurements are too shallow to apply existing acoustic Doppler current profiler techniques for flow measurements of satisfactory quality. Because the same transducer is used for both transmitting and receiving acoustic signals in most Doppler current profilers, some small time delay is required for acoustic "ringing" to be damped out of transducers before meaningful measurements can be made. The result of that time delay is that velocity measurements cannot be made close to the transducer thus limiting the usefulness of these instruments in shallow regions. Manufacturers and users are constantly striving for improvements to acoustic instruments which would permit useful discharge measurements in shallow rivers and streams that are still often measured with techniques and instruments more than a century old. One promising area of advance appeared to be reduction of time delay (blank) required between transmitting and receiving signals during acoustic velocity measurements. Development of a low- or zero-blank transducer by RD Instruments3 held promise that velocity measurements could be made much closer to the transducer and thus in much shallower water. Initial experience indicates that this is not the case; limitation of measurement quality appears to be related to the physical presence of the transducer itself within the flow field. The limitation may be the result of changes to water flow pattern close to the transducer rather than transducer ringing characteristics as a function of blanking distance. Results of field experiments are discussed that support this conclusion and some minimum measurement distances from transducer are suggested based on water current speed and ADCP sample modes.

The integrated water balance and soil data set of the Rollesbroich hydrological observatory

NASA Astrophysics Data System (ADS)

Qu, Wei; Bogena, Heye R.; Huisman, Johan A.; Schmidt, Marius; Kunkel, Ralf; Weuthen, Ansgar; Schiedung, Henning; Schilling, Bernd; Sorg, Jürgen; Vereecken, Harry

2016-10-01

The Rollesbroich headwater catchment located in western Germany is a densely instrumented hydrological observatory and part of the TERENO (Terrestrial Environmental Observatories) initiative. The measurements acquired in this observatory present a comprehensive data set that contains key hydrological fluxes in addition to important hydrological states and properties. Meteorological data (i.e., precipitation, air temperature, air humidity, radiation components, and wind speed) are continuously recorded and actual evapotranspiration is measured using the eddy covariance technique. Runoff is measured at the catchment outlet with a gauging station. In addition, spatiotemporal variations in soil water content and temperature are measured at high resolution with a wireless sensor network (SoilNet). Soil physical properties were determined using standard laboratory procedures from samples taken at a large number of locations in the catchment. This comprehensive data set can be used to validate remote sensing retrievals and hydrological models, to improve the understanding of spatial temporal dynamics of soil water content, to optimize data assimilation and inverse techniques for hydrological models, and to develop upscaling and downscaling procedures of soil water content information. The complete data set is freely available online (http://www.tereno.net, doi:10.5880/TERENO.2016.001, doi:10.5880/TERENO.2016.004, doi:10.5880/TERENO.2016.003) and additionally referenced by three persistent identifiers securing the long-term data and metadata availability.

Fatalities caused by spherical bullets fired from blank cartridge guns in Istanbul, Turkey.

PubMed

Uzün, Ibrahim; Büyük, Yalçin; Erkol, Zerrin; Ağritmiş, Hasan; Kir, Ziya

2009-09-01

Blank cartridge guns are generally regarded as being harmless and are not considered to be firearms in the legal sense in most countries. To show the danger of these guns upon simple modifications, we report 59 fatalities resulting from these simply modified blank cartridge guns in Istanbul, Turkey. The great majority of the victims were males and the age of those ranged from 11 to 61 years. In 55.9% of these cases, homicide was the origin followed by suicide (39%). The right temporal region was detected to be the preferred region in suicidal shots by blank cartridge guns with a frequency of 56.5%. In trial shots, all these guns were detected to discharge steel or lead spherical objects, generally 4 or 5 mm in diameter, successfully. Our findings strongly suggest that these guns should also be considered as handguns in the legal sense.

Failure Analysis of a Sheet Metal Blanking Process Based on Damage Coupling Model

NASA Astrophysics Data System (ADS)

Wen, Y.; Chen, Z. H.; Zang, Y.

2013-11-01

In this paper, a blanking process of sheet metal is studied by the methods of numerical simulation and experimental observation. The effects of varying technological parameters related to the quality of products are investigated. An elastoplastic constitutive equation accounting for isotropic ductile damage is implemented into the finite element code ABAQUS with a user-defined material subroutine UMAT. The simulations of the damage evolution and ductile fracture in a sheet metal blanking process have been carried out by the FEM. In order to guarantee computation accuracy and avoid numerical divergence during large plastic deformation, a specified remeshing technique is successively applied when severe element distortion occurs. In the simulation, the evolutions of damage at different stage of the blanking process have been evaluated and the distributions of damage obtained from simulation are in proper agreement with the experimental results.

The sound insulations of studio doors. Part 1: Door blanks

NASA Astrophysics Data System (ADS)

Plumb, G. D.; Clark, R.

The sound insulations of a range of different door blanks were measured. The results were compared with the sound insulations of existing BBC door blanks. The new doors were made from medium density fiberboard (MDF) which is more stable than the blockboard used in existing studio doors. Consequently, they should require less maintenance and adjustment and should have a longer lifespan. The doors had higher sound insulations for their weight than existing designs, which might permit savings in the costs of the surrounding building structures. Overall construction costs of the door blanks themselves are likely to be similar to those of existing designs. A companion Report (BBC RD 1994/15) describes sound insulation measurements made on plant-on door seals. The intention of this work was to simplify the construction of the door frame and the fitting of the seals to reduce costs.

Method and apparatus for inspecting reflection masks for defects

DOEpatents

Bokor, Jeffrey; Lin, Yun

2003-04-29

An at-wavelength system for extreme ultraviolet lithography mask blank defect detection is provided. When a focused beam of wavelength 13 nm is incident on a defective region of a mask blank, three possible phenomena can occur. The defect will induce an intensity reduction in the specularly reflected beam, scatter incoming photons into an off-specular direction, and change the amplitude and phase of the electric field at the surface which can be monitored through the change in the photoemission current. The magnitude of these changes will depend on the incident beam size, and the nature, extent and size of the defect. Inspection of the mask blank is performed by scanning the mask blank with 13 nm light focused to a spot a few .mu.m in diameter, while measuring the reflected beam intensity (bright field detection), the scattered beam intensity (dark-field detection) and/or the change in the photoemission current.

Measurements of the dissolved inorganic carbon system and associated biogeochemical parameters in the Canadian Arctic, 1974-2009

NASA Astrophysics Data System (ADS)

Giesbrecht, K. E.; Miller, L. A.; Davelaar, M.; Zimmermann, S.; Carmack, E.; Johnson, W. K.; Macdonald, R. W.; McLaughlin, F.; Mucci, A.; Williams, W. J.; Wong, C. S.; Yamamoto-Kawai, M.

2014-03-01

We have assembled and conducted primary quality control on previously publicly unavailable water column measurements of the dissolved inorganic carbon system and associated biogeochemical parameters (oxygen, nutrients, etc.) made on 26 cruises in the subarctic and Arctic regions dating back to 1974. The measurements are primarily from the western side of the Canadian Arctic, but also include data that cover an area ranging from the North Pacific to the Gulf of St. Lawrence. The data were subjected to primary quality control (QC) to identify outliers and obvious errors. This data set incorporates over four thousand individual measurements of total inorganic carbon (TIC), alkalinity, and pH from the Canadian Arctic over a period of more than 30 years and provides an opportunity to increase our understanding of temporal changes in the inorganic carbon system in northern waters and the Arctic Ocean. The data set is available for download on the CDIAC (Carbon Dioxide Information Analysis Center) website: http://cdiac.ornl.gov/ftp/oceans/IOS_Arctic_Database/ (doi:10.3334/CDIAC/OTG.IOS_ARCT_CARBN).

Detection of Stimulus Displacements Across Saccades is Capacity-Limited and Biased in Favor of the Saccade Target

PubMed Central

Irwin, David E.; Robinson, Maria M.

2015-01-01

Retinal image displacements caused by saccadic eye movements are generally unnoticed. Recent theories have proposed that perceptual stability across saccades depends on a local evaluation process centered on the saccade target object rather than on remapping and evaluating the positions of all objects in a display. In three experiments, we examined whether objects other than the saccade target also influence perceptual stability by measuring displacement detection thresholds across saccades for saccade targets and a variable number of non-saccade objects. We found that the positions of multiple objects are maintained across saccades, but with variable precision, with the saccade target object having priority in the perception of displacement, most likely because it is the focus of attention before the saccade and resides near the fovea after the saccade. The perception of displacement of objects that are not the saccade target is affected by acuity limitations, attentional limitations, and limitations on memory capacity. Unlike previous studies that have found that a postsaccadic blank improves the detection of displacement direction across saccades, we found that postsaccadic blanking hurt the detection of displacement per se by increasing false alarms. Overall, our results are consistent with the hypothesis that visual working memory underlies the perception of stability across saccades. PMID:26640430

Systems Engineering and Project Management for Product Development: Optimizing Their Working Interfaces

DTIC Science & Technology

2013-09-01

reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instruction...Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2. REPORT DATE... 1   A.  BACKGROUND ................................................................................... 1   B.  PRODUCT DEVELOPMENT

2. D Street facade and rear (east) blank wall of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. D Street facade and rear (east) blank wall of parking garage. Farther east is 408 8th Street (National Art And Frame Company). - PMI Parking Garage, 403-407 Ninth Street, Northwest, Washington, District of Columbia, DC

Broadband Optical Active Waveguides Written by Femtosecond Laser Pulses in Lithium Fluoride

NASA Astrophysics Data System (ADS)

Ismael, Chiamenti; Francesca, Bonfigli; Anderson, S. L. Gomes; Rosa, Maria Montereali; Larissa, N. da Costa; Hypolito, J. Kalinowski

2014-01-01

Broadband waveguiding through light-emitting strips directly written in a blank lithium fluoride crystal with a femtosecond laser is reported. Light guiding was observed at several optical wavelengths, from blue, 458 nm, to near-infrared, at 1550 nm. Visible photoluminescence spectra of the optically active F2 and F3+ color centers produced by the fs laser writing process were measured. The wavelength-dependent refractive index increase was estimated to be in the order of 10-3-10-4 in the visible and near-infrared spectral intervals, which is consistent with the stable formation of point defects in LiF.

Micro-Teaching Tapes in Anatomy and Physiology.

ERIC Educational Resources Information Center

Stencel, John E.

1981-01-01

Outlines the development and use of micro-teaching tapes as a means of supplemental instruction for college anatomy and physiology classes. Tapes include brief explanations of difficult concepts taken from lectures as students listen to cassette tapes and fill in blanks, or answer questions. (DS)

77 FR 6584 - Specialty Bar Products Company,a Subsidiary of Doncasters, Inc., Blairsville, PA; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-08

... gun blanks. The initial investigation resulted in a negative determination based on the findings that the subject firm did not shift the production of pins, bushings, gun blanks (or like or directly...

Modeling of the minimum variable blank holder force based on forming limit diagram (FLD) in deep drawing process

NASA Astrophysics Data System (ADS)

Candra, S.; Batan, I. M. L.; Berata, W.; Pramono, A. S.

2017-11-01

This paper presents the mathematical approach of minimum blank holder force to prevent wrinkling in deep drawing process of the cylindrical cup. Based on the maximum of minor-major strain ratio, the slab method was applied to determine the modeling of minimum variable blank holder force (VBHF) and it compared to FE simulation. The Tin steel sheet of T4-CA grade, with the thickness of 0.2 mm was used in this study. The modeling of minimum VBHF can be used as a simple reference to prevent wrinkling in deep drawing.

Numerical investigation of effects on blanks for press hardening process during longitudinal flux heating

NASA Astrophysics Data System (ADS)

Dietrich, André; Nacke, Bernard

2018-05-01

With the induction heating technology, it is possible to heat up blanks for the press hardening process in 20 s or less. Furthermore, the dimension of an induction system is small and easy to control in comparison to conventional heating systems. To bring the induction heating technology to warm forming industry it is necessary to analyze the process under the view of induction. This paper investigates the edge- and end-effects of a batch heated blank. The results facilitate the later design of induction heating systems for the batch process.

Closed-Loop Control of Myoelectric Prostheses With Electrotactile Feedback: Influence of Stimulation Artifact and Blanking.

PubMed

Hartmann, Cornelia; Dosen, Strahinja; Amsuess, Sebastian; Farina, Dario

2015-09-01

Electrocutaneous stimulation is a promising approach to provide sensory feedback to amputees, and thus close the loop in upper limb prosthetic systems. However, the stimulation introduces artifacts in the recorded electromyographic (EMG) signals, which may be detrimental for the control of myoelectric prostheses. In this study, artifact blanking with three data segmentation approaches was investigated as a simple method to restore the performance of pattern recognition in prosthesis control (eight motions) when EMG signals are corrupted by stimulation artifacts. The methods were tested over a range of stimulation conditions and using four feature sets, comprising both time and frequency domain features. The results demonstrated that when stimulation artifacts were present, the classification performance improved with blanking in all tested conditions. In some cases, the classification performance with blanking was at the level of the benchmark (artifact-free data). The greatest pulse duration and frequency that allowed a full performance recovery were 400 μs and 150 Hz, respectively. These results show that artifact blanking can be used as a practical solution to eliminate the negative influence of the stimulation artifact on EMG pattern classification in a broad range of conditions, thus allowing to close the loop in myoelectric prostheses using electrotactile feedback.

Magnetron sputtering for the production of EUV mask blanks

NASA Astrophysics Data System (ADS)

Kearney, Patrick; Ngai, Tat; Karumuri, Anil; Yum, Jung; Lee, Hojune; Gilmer, David; Vo, Tuan; Goodwin, Frank

2015-03-01

Ion Beam Deposition (IBD) has been the primary technique used to deposit EUV mask blanks since 1995 when it was discovered it could produce multilayers with few defects. Since that time the IBD technique has been extensively studied and improved and is finally approaching usable defectivities. But in the intervening years, the defectivity of magnetron sputtering has been greatly improved. This paper evaluates the suitability of a modern magnetron tool to produce EUV mask blanks and the ability to support HVM production. In particular we show that the reflectivity and uniformity of these tools are superior to current generation IBD tools, and that the magnetron tools can produce EUV films with defect densities comparable to recent best IBD tool performance. Magnetron tools also offer many advantages in manufacturability and tool throughput; however, challenges remain, including transitioning the magnetron tools from the wafer to mask formats. While work continues on quantifying the capability of magnetron sputtering to meet the mask blank demands of the industry, for the most part the remaining challenges do not require any fundamental improvements to existing technology. Based on the recent results and the data presented in this paper there is a clear indication that magnetron deposition should be considered for the future of EUV mask blank production.

Evaluation of the memory effect on gold-coated silica adsorption tubes used for the analysis of gaseous mercury by cold vapor atomic absorption spectrometry.

PubMed

Rahman, Mohammad Mahmudur; Brown, Richard J C; Kim, Ki-Hyun; Yoon, Hye-On; Phan, Nhu-Thuc

2013-01-01

In an effort to reduce the experimental bias involved in the analysis of gaseous elemental mercury (Hg(o)), the blank response from gold-coated adsorption tubes has been investigated using cold vapor atomic absorption spectrometry (CVAAS). Our study has been compared with our recent investigation on memory effect in a cold vapour atomic fluorescence spectrometry (CVAFS). The pattern of blank responses was quantified after loading different amounts of mercury and after different time intervals of 1, 14, and 45 days. In case of the one day interval, the result of five to six instant blank heating cycles confirmed successful liberation of mercury following the second and third blank heating cycles. The results of 14 or 45 days generally suggest that liberation of excess mercury is affected by both the initial loading amount and the length of storage time prior to analysis. We have demonstrated a possibly effective way to reduce memory effects. Some similarities of these results with those from CVAFS experiment suggests that the blank response is caused by a combination of mercury absorbed within the bulk gold and micro- and nanoparticles liberated during heating and not from coabsorbing interfering gaseous species.

Evaluation of the Memory Effect on Gold-Coated Silica Adsorption Tubes Used for the Analysis of Gaseous Mercury by Cold Vapor Atomic Absorption Spectrometry

PubMed Central

Rahman, Mohammad Mahmudur; Brown, Richard J. C.; Yoon, Hye-On; Phan, Nhu-Thuc

2013-01-01

In an effort to reduce the experimental bias involved in the analysis of gaseous elemental mercury (Hgo), the blank response from gold-coated adsorption tubes has been investigated using cold vapor atomic absorption spectrometry (CVAAS). Our study has been compared with our recent investigation on memory effect in a cold vapour atomic fluorescence spectrometry (CVAFS). The pattern of blank responses was quantified after loading different amounts of mercury and after different time intervals of 1, 14, and 45 days. In case of the one day interval, the result of five to six instant blank heating cycles confirmed successful liberation of mercury following the second and third blank heating cycles. The results of 14 or 45 days generally suggest that liberation of excess mercury is affected by both the initial loading amount and the length of storage time prior to analysis. We have demonstrated a possibly effective way to reduce memory effects. Some similarities of these results with those from CVAFS experiment suggests that the blank response is caused by a combination of mercury absorbed within the bulk gold and micro- and nanoparticles liberated during heating and not from coabsorbing interfering gaseous species. PMID:23589708

Checking the Dark Matter Origin of a 3.53 keV Line with the Milky Way Center.

PubMed

Boyarsky, A; Franse, J; Iakubovskyi, D; Ruchayskiy, O

2015-10-16

We detect a line at 3.539±0.011  keV in the deep exposure data set of the Galactic center region, observed with the x-ray multi-mirror mission Newton. The dark matter interpretation of the signal observed in the Perseus galaxy cluster, the Andromeda galaxy [A. Boyarsky et al., Phys. Rev. Lett. 113, 251301 (2014)], and in the stacked spectra of galaxy clusters [E. Bulbul et al., Astrophys. J. 789, 13 (2014)], together with nonobservation of the line in blank-sky data, put both lower and upper limits on the possible intensity of the line in the Galactic center data. Our result is consistent with these constraints for a class of Milky Way mass models, presented previously by observers, and would correspond to the radiative decay dark matter lifetime, τDM∼6-8×10(27)  sec. Although it is hard to exclude an astrophysical origin of this line based on the Galactic center data alone, this is an important consistency check of the hypothesis that encourages us to check it with more observational data that are expected by the end of 2015.

Design and Development of a Counter Swarm Prototype Air Vehicle

DTIC Science & Technology

2017-12-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release. Distribution is unlimited. DESIGN AND DEVELOPMENT OF A...INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this collection of information is...number ____N/A____. 12a. DISTRIBUTION / AVAILABILITY STATEMENT Approved for public release. Distribution is unlimited. 12b. DISTRIBUTION CODE 13

Effects of Post-Weld Heat Treatment on the Mechanical Properties of Similar- and Dissimilar-Alloy Friction Stir Welded Blanks

NASA Astrophysics Data System (ADS)

Zadpoor, Amir Abbas; Sinke, Jos

2011-01-01

Friction stir welding is a solid state joining process with relatively low welding temperatures. Nevertheless, the mechanical properties of friction stir welded blanks are degraded after welding. Indeed, both strength and ductility of the welds are decreased after welding. Often, the resulting friction stir welded blanks need to be formed to their final structural shape. Therefore, the formability of friction stir welded blanks is of primary importance in the manufacturing of structural parts. This paper studies how the mechanical properties and particularly formability of friction stir welded blanks can be improved by applying a post weld heat treatment. Two aluminum alloys from 2000 and 7000 series, namely 2024-T3 and 7075-T6, are selected for the study. The sheet thickness of both materials is 2,0 mm. The selected alloys are welded in three configurations: 2024-T3 and 2024-T3, 7075-T6 and 7075-T6, and 2024-T3 and 7075-T6. The resulting welds are naturally aged for a few months. Three sets of standard dog bone shape tensile test specimens are then machined from the welds. The first set of the specimens is tested without any heat treatment. The second set of the specimens is solution heat treated and quenched before testing. The third set of the specimens is solution heat treated, quenched, and naturally aged for a week before testing. The mechanical properties of the three different sets of specimens are compared with each other. It is shown that careful selection of post weld heat-treatment can greatly improve the formability of friction stir welded blanks.

Some case studies of skewed (and other ab-normal) data distributions arising in low-level environmental research.

PubMed

Currie, L A

2001-07-01

Three general classes of skewed data distributions have been encountered in research on background radiation, chemical and radiochemical blanks, and low levels of 85Kr and 14C in the atmosphere and the cryosphere. The first class of skewed data can be considered to be theoretically, or fundamentally skewed. It is typified by the exponential distribution of inter-arrival times for nuclear counting events for a Poisson process. As part of a study of the nature of low-level (anti-coincidence) Geiger-Muller counter background radiation, tests were performed on the Poisson distribution of counts, the uniform distribution of arrival times, and the exponential distribution of inter-arrival times. The real laboratory system, of course, failed the (inter-arrival time) test--for very interesting reasons, linked to the physics of the measurement process. The second, computationally skewed, class relates to skewness induced by non-linear transformations. It is illustrated by non-linear concentration estimates from inverse calibration, and bivariate blank corrections for low-level 14C-12C aerosol data that led to highly asymmetric uncertainty intervals for the biomass carbon contribution to urban "soot". The third, environmentally, skewed, data class relates to a universal problem for the detection of excursions above blank or baseline levels: namely, the widespread occurrence of ab-normal distributions of environmental and laboratory blanks. This is illustrated by the search for fundamental factors that lurk behind skewed frequency distributions of sulfur laboratory blanks and 85Kr environmental baselines, and the application of robust statistical procedures for reliable detection decisions in the face of skewed isotopic carbon procedural blanks with few degrees of freedom.

Cognitive Work Analysis: Foundations, Extensions, and Challenges

DTIC Science & Technology

2011-11-01

1 . Introduction A quarter of a century has passed since Jens Rasmussen published his first...achievements is the development of the cognitive work analysis framework itself, which has its origins in the work of Jens Rasmussen and his colleagues...intentionally blank UNCLASSIFIED DSTO-GD-0680 Contents 1 . INTRODUCTION

Adjustable extender for instrument module

DOEpatents

Sevec, J.B.; Stein, A.D.

1975-11-01

A blank extender module used to mount an instrument module in front of its console for repair or test purposes has been equipped with a rotatable mount and means for locking the mount at various angles of rotation for easy accessibility. The rotatable mount includes a horizontal conduit supported by bearings within the blank module. The conduit is spring-biased in a retracted position within the blank module and in this position a small gear mounted on the conduit periphery is locked by a fixed pawl. The conduit and instrument mount can be pulled into an extended position with the gear clearing the pawl to permit rotation and adjustment of the instrument.

Method for making devices having intermetallic structures and intermetallic devices made thereby

DOEpatents

Paul, Brian Kevin; Wilson, Richard Dean; Alman, David Eli

2004-01-06

A method and system for making a monolithic intermetallic structure are presented. The structure is made from lamina blanks which comprise multiple layers of metals which are patternable, or intermetallic lamina blanks that are patternable. Lamina blanks are patterned, stacked and registered, and processed to form a monolithic intermetallic structure. The advantages of a patterned monolithic intermetallic structure include physical characteristics such as melting temperature, thermal conductivity, and corrosion resistance. Applications are broad, and include among others, use as a microreactor, heat recycling device, and apparatus for producing superheated steam. Monolithic intermetallic structures may contain one or more catalysts within the internal features.

Mercury Deposition Network Site Operator Training for the System Blank and Blind Audit Programs

USGS Publications Warehouse

Wetherbee, Gregory A.; Lehmann, Christopher M.B.

2008-01-01

The U.S. Geological Survey operates the external quality assurance project for the National Atmospheric Deposition Program/Mercury Deposition Network. The project includes the system blank and blind audit programs for assessment of total mercury concentration data quality for wet-deposition samples. This presentation was prepared to train new site operators and to refresh experienced site operators to successfully process and submit system blank and blind audit samples for chemical analysis. Analytical results are used to estimate chemical stability and contamination levels of National Atmospheric Deposition Program/Mercury Deposition Network samples and to evaluate laboratory variability and bias.

Social Impacts Module (SIM) Transition

DTIC Science & Technology

2012-09-28

User String The authorized user’s name to access the PAVE database. Applies only to Microsoft SQL Server; leave blank, otherwise. passwd String The...otherwise. passwd String The password if an authorized user’s name is required; otherwise, leave blank driver String The class name for the driver to

Evolving from Course-Centric to Learning-Centric: Portfolios, Wikis, and Social Learning

ERIC Educational Resources Information Center

Everhart, Deborah

2006-01-01

Teaching and learning strategies for using course management systems have evolved from basic "fill in the blank" models to interactive designs that encourage multi-formatted individual contributions and collaborative forms of learning. In keeping with the participatory development of online resources, web-based courses are shifting from…

Designing the Horizons of Your Small Business.

ERIC Educational Resources Information Center

Helgemo, Robert R.

This manual outlines the planning process for developing a feasibility study for a small business. The material is composed of three parts: the planning documents filled out for an imaginary campground; a business plan summarized from the planning documents; and blank planning documents with introductions and instructions. The documents can be…

Development of Three-Phase Source Inverter for Research and Laboratories

DTIC Science & Technology

2011-03-01

Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2 . REPORT DATE March 2011 3. REPORT TYPE AND...THEORY OF OPERATION ................................5 1 . Overview ......................................5 2 . Voltage Source Inverter...29 1 . Low Pass Filter MATLAB Code ..................31 2 . Current Sensor ...............................33 3. Optocouplers

Lowest cost due to highest productivity and highest quality

NASA Astrophysics Data System (ADS)

Wenk, Daniel

2003-03-01

Since global purchasing in the automotive industry has been taken up all around the world there is one main key factor that makes a TB-supplier today successful: Producing highest quality at lowest cost. The fact that Tailored Blanks, which today may reach up to 1/3 of a car body weight, are purchased on the free market but from different steel suppliers, especially in Europe and NAFTA, the philosophy on OEM side has been changing gradually towards tough evaluation criteria. "No risk at the stamping side" calls for top quality Tailored- or Tubular Blank products. Outsourcing Tailored Blanks has been starting in Japan but up to now without any quality request from the OEM side like ISO 13919-1B (welding quality standard in Europe and USA). Increased competition will automatically push the quality level and the ongoing approach to combine high strength steel with Tailored- and Tubular Blanks will ask for even more reliable system concepts which enables to weld narrow seams at highest speed. Beside producing quality, which is the key to reduce one of the most important cost driver "material scrap," in-line quality systems with true and reliable evaluation is going to be a "must" on all weld systems. Traceability of all process related data submitted to interfaces according to customer request in combination with ghost-shift-operation of TB systems are tomorrow's state-of-the-art solutions of Tailored Blank-facilities.

Inverse Analysis to Formability Design in a Deep Drawing Process

NASA Astrophysics Data System (ADS)

Buranathiti, Thaweepat; Cao, Jian

Deep drawing process is an important process adding values to flat sheet metals in many industries. An important concern in the design of a deep drawing process generally is formability. This paper aims to present the connection between formability and inverse analysis (IA), which is a systematical means for determining an optimal blank configuration for a deep drawing process. In this paper, IA is presented and explored by using a commercial finite element software package. A number of numerical studies on the effect of blank configurations to the quality of a part produced by a deep drawing process were conducted and analyzed. The quality of the drawing processes is numerically analyzed by using an explicit incremental nonlinear finite element code. The minimum distance between elemental principal strains and the strain-based forming limit curve (FLC) is defined as tearing margin to be the key performance index (KPI) implying the quality of the part. The initial blank configuration has shown that it plays a highly important role in the quality of the product via the deep drawing process. In addition, it is observed that if a blank configuration is not greatly deviated from the one obtained from IA, the blank can still result a good product. The strain history around the bottom fillet of the part is also observed. The paper concludes that IA is an important part of the design methodology for deep drawing processes.

Summary and evaluation of pesticides in field blanks collected for the National Water-Quality Assessment Program, 1992-95

USGS Publications Warehouse

Martin, Jeffrey D.; Gilliom, Robert J.; Schertz, Terry L.

1999-01-01

Field blanks did show evidence of contamination by some pesticides. Most of the pesticides detected in field blanks, however, were detected more frequently and at higher concentrations in environmental water samples. Two criteria were used to evaluate the need to consider contamination in water-quality assessments: (1) a ratio of the frequency of pesticide detection in environmental water samples to the frequency of detection in field blanks of 5.0 or less and (2) a ratio of the median concentration detected in environmental water samples to the maximum concentration detected in field blanks of 2.0 or less. These criteria indicate that contamination, for the majority of the pesticide data collected for the NAWQA Program, probably does not need to be considered in the analysis and interpretation of (1) the frequency of pesticide detection or (2) the median concentration of pesticides detected. Contamination must be considered, however, in detection frequency for cispermethrin, pronamide, p,p' -DDE, pebulate, propargite, ethalfluralin, and triallate in surface water and fenuron, benfluralin, pronamide, cis-permethrin, triallate, chlorpyrifos, trifluralin, propanil, p,p' -DDE, bromacil, dacthal, diazinon, and diuron in ground water. Contamination also must be considered in median concentrations detected for pronamide, p,p' -DDE, propargite, napropamide, and triallate in surface water and benfluralin, cis-permethrin, triallate, chlorpyrifos, trifluralin, p,p' -DDE, dacthal, and diazinon in ground water.

Production of the 4.26 m ZERODUR mirror blank for the Advanced Technology Solar telescope (ATST)

NASA Astrophysics Data System (ADS)

Jedamzik, Ralf; Werner, Thomas; Westerhoff, Thomas

2014-07-01

The Daniel K. Inouye Solar Telescope (DKIST, formerly the Advanced Technology Solar Telescope, ATST) will be the most powerful solar telescope in the world. It is currently being built by the Association of Universities for Research in Astronomy (AURA) in a height of 3000 m above sea level on the mountain Haleakala of Maui, Hawaii. The primary mirror blank of diameter 4.26 m is made of the extremely low thermal expansion glass ceramic ZERODUR® of SCHOTT AG Advanced Optics. The DKIST primary mirror design is extremely challenging. With a mirror thickness of only 78 to 85 mm it is the smallest thickness ever machined on a mirror of 4.26 m in diameter. Additionally the glassy ZERODUR® casting is one of the largest in size ever produced for a 4 m class ZERODUR® mirror blank. The off axis aspherical mirror surface required sophisticated grinding procedures to achieve the specified geometrical tolerance. The small thickness of about 80 mm required special measures during processing, lifting and transport. Additionally acid etch treatment was applied to the convex back-surface and the conical shaped outer diameter surface to improve the strength of the blank. This paper reports on the challenging tasks and the achievements on the material property and dimensional specification parameter during the production of the 4.26 m ZERODUR® primary mirror blank for AURA.

Information Operations and FATA Integration into the National Mainstream

DTIC Science & Technology

2012-09-01

Edward L. Fisher THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting burden for this...LEFT BLANK vii TABLE OF CONTENTS I . INTRODUCTION ............................................................................................. 1...39 ix i . Computer Network Operations .................................. 40 j. CNO as an IO Core Capability .................................... 40

Nitrogen-Noble Gas Static Mass Sepectrometry of Genesis Collector Materials

NASA Astrophysics Data System (ADS)

Marty, B.; Burnard, P.; Zimmermann, L.; Robert, P.

2005-03-01

Gases (N, Ne, Ar) are extracted from Au-coated sapphire and diamond-like carbon collectors using an F2 excimer laser, without blank contributions the substrate. N is purified using a low blank CuO/Cu cycle prior to analysis by high resolution multicollector mass spectrometer.

Some Data Concerning the Vocational Preference Inventory Scales and the Strong Vocational Interest Blank

ERIC Educational Resources Information Center

Cockriel, Irvin W.

1972-01-01

Occupational scales of the Vocational Preference Inventory were correlated with the Basic Interest scales of the Strong Vocational Interest Blank. The 285 subjects were women freshmen in a College of Education. The results indicate that the scales are not highly correlated. (Author)

76 FR 50537 - Regulatory Guidance Concerning Household Goods Carriers Requiring Shippers To Sign Blank or...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-15

... Concerning Household Goods Carriers Requiring Shippers To Sign Blank or Incomplete Documents AGENCY: Federal.... Basis for This Notice The Agency has received numerous consumer complaints concerning household goods.... The FMCSA is issuing this regulatory guidance to eliminate any ambiguity or confusion concerning the...

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--QA ANALYTICAL RESULTS FOR PARTICULATE MATTER IN BLANK SAMPLES

EPA Science Inventory

The Particulate Matter in Blank Samples data set contains the analytical results for measurements of two particle sizes in 12 samples. Filters were pre-weighed, loaded into impactors, kept unexposed in the laboratory, unloaded and post-weighed. Positive weight gains for laborat...

Using a Functional Architecture to Identify Human-Automation Trust Needs and Design Requirements

DTIC Science & Technology

2016-12-01

FUNCTIONAL ARCHITECTURE TO IDENTIFY HUMAN-AUTOMATION TRUST NEEDS AND DESIGN REQUIREMENTS by Bradley A. Johnson December 2016 Thesis Advisor...maximum 200 words) This thesis develops and analyzes the functional architecture for an “autonomous” unmanned aerial system performing an...INTENTIONALLY LEFT BLANK v ABSTRACT This thesis develops and analyzes the functional architecture for an “autonomous” unmanned aerial system

USSR Report, Science and Technology Policy.

DTIC Science & Technology

1987-01-29

one has to send all the documents plus a photograph of the forceps facing front and in profile together with a patent blank for the consideration of...establishment of all-union scientific production associations promises. Your Kriotekhnika will become a monopolistic developer and producer, there will be... prices for watches and jewelry and developing enterprises accordingly, the Ministry of Instrument Making, Automation Equipment, and Control Systems

Lessons Learned from the 14-Year Systems Development of the Marine Corps Standard Accounting, Budgeting and Reporting System (SABRS)

DTIC Science & Technology

1994-03-01

22202-4302. and to the Office of Managmnt and Budget, Paperwork Reduction Project (0704-0188) Wahington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2...Project Officer ........................ 49 d. Program Management ..................... 50 2. User/Systems Development Team Relationship ...... 52 D...and 60’s, when programming and systems development was in its infancy, virtually all software was custom -made. The programmer designed, coded

Getting Ugly: Exploring Network Development in The Ugly American

DTIC Science & Technology

2012-12-01

Budget, Paperwork Reduction Project (0704–0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE December 2012 3. REPORT TYPE... century , serves as a foundation for the examination of indigenous network development at both the operational and tactical levels. The goal of this thesis...20th century , serves as a foundation for the examination of indigenous network development at both the operational and tactical levels. The goal of

A multi-decadal wind-wave hindcast for the North Sea 1949-2014: coastDat2

NASA Astrophysics Data System (ADS)

Groll, Nikolaus; Weisse, Ralf

2017-12-01

Long and consistent wave data are important for analysing wave climate variability and change. Moreover, such wave data are also needed in coastal and offshore design and for addressing safety-related issues at sea. Using the third-generation spectral wave model WAM a multi-decadal wind-wave hindcast for the North Sea covering the period 1949-2014 was produced. The hindcast is part of the coastDat database representing a consistent and homogeneous met-ocean data set. It is shown that despite not being perfect, data from the wave hindcast are generally suitable for wave climate analysis. In particular, comparisons of hindcast data with in situ and satellite observations show on average a reasonable agreement, while a tendency towards overestimation of the highest waves could be inferred. Despite these limitations, the wave hindcast still provides useful data for assessing wave climate variability and change as well as for risk analysis, in particular when conservative estimates are needed. Hindcast data are stored at the World Data Center for Climate (WDCC) and can be freely accessed using the doi:10.1594/WDCC/coastDat-2_WAM-North_Sea Groll and Weisse(2016) or via the coastDat web-page http://www.coastdat.de.

Formulation and in vitro characterization of novel sildenafil citrate-loaded polyvinyl alcohol-polyethylene glycol graft copolymer-based orally dissolving films.

PubMed

Xu, Li-Li; Shi, Li-Li; Cao, Qing-Ri; Xu, Wei-Juan; Cao, Yue; Zhu, Xiao-Yin; Cui, Jing-Hao

2014-10-01

This work was aimed to develop novel sildenafil citrate (SC)-loaded polyvinyl alcohol (PVA)-polyethylene glycol (PEG) graft copolymer (Kollicoat(®) IR)-based orally dissolving films (ODFs) using a solvent casting method. Formulation factors such as plasticizers and disintegrants were optimized on the basis of characteristics of blank ODFs. The SC-loaded ODF with a loading capacity up to 6.25mg in an area of 6 cm(2) was prepared and evaluated in terms of mechanical properties, disintegration time and dissolution rate. The physicochemical properties of drug-loaded ODF were also investigated using the scanning electron microscope (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR). The blank ODF composed of Kollicoat(®) IR, sodium alginate (ALG-Na) and glycerol (10:2:1.5, w/w) had a remarkably short disintegration time of about 20s. The SC-loaded ODF showed a delayed disintegration time (about 25s), but exhibited improved mechanical properties when compared to the blank ODF. SC was homogeneously dispersed throughout the ODF and the crystalline form of drug had been partly changed, existing strong hydrogen bonding between the drug and carriers. The Kollicoat(®) IR/ALG-Na based ODFs containing SC might be an alternative to conventional tablet for the treatment of male erectile dysfunction. Copyright © 2014 Elsevier B.V. All rights reserved.

Toward an interim standard for patient-centered knowledge-access.

PubMed Central

Tuttle, M. S.; Sherertz, D. D.; Fagan, L. M.; Carlson, R. W.; Cole, W. G.; Schipma, P. B.; Nelson, S. J.

1993-01-01

Most care-giver "knowledge" needs arise at the point of care and are "patient-centered." Many of these knowledge needs can be met using existing on-line knowledge sources, but the process is too time-consuming, currently, for even the computer-proficient. We are developing a set of public domain standards aimed at bringing potentially relevant knowledge to the point of care in a straight-forward and timely fashion. The standards will a) make use of selected items from a Computer-based Patient Record (CPR), e.g., a diagnosis and measure of severity, b) anticipate certain care-giver knowledge needs, e.g., "therapy," "protocols," "complications," and c) try to satisfy those needs from available knowledge sources, e.g., knowledge-bases, citation databases, practice guidelines, and on-line textbooks. The standards will use templates, i.e., fill-in-the-blank structures, to anticipate knowledge needs and UMLS Metathesaurus enhancements to represent the content of knowledge sources. Together, the standards will form the specification for a "Knowledge-Server" (KS) designed to be accessed from any CPR system. Plans are in place to test an interim version of this specification in the context of medical oncology. We are accumulating anecdotal evidence that a KS operating in conjunction with a CPR is much more compelling to users than either a CPR or a KS operating alone. PMID:8130537

Evaluation of quality-control data collected by the U.S. Geological Survey for routine water-quality activities at the Idaho National Laboratory, Idaho, 1996–2001

USGS Publications Warehouse

Rattray, Gordon W.

2012-01-01

The U.S. Geological Survey, in cooperation with the U.S. Department of Energy, collects surface water and groundwater samples at and near the Idaho National Laboratory as part of a routine, site-wide, water-quality monitoring program. Quality-control samples are collected as part of the program to ensure and document the quality of environmental data. From 1996 to 2001, quality-control samples consisting of 204 replicates and 27 blanks were collected at sampling sites. Paired measurements from replicates were used to calculate variability (as reproducibility and reliability) from sample collection and analysis of radiochemical, chemical, and organic constituents. Measurements from field and equipment blanks were used to estimate the potential contamination bias of constituents. The reproducibility of measurements of constituents was calculated from paired measurements as the normalized absolute difference (NAD) or the relative standard deviation (RSD). The NADs and RSDs, as well as paired measurements with censored or estimated concentrations for which NADs and RSDs were not calculated, were compared to specified criteria to determine if the paired measurements had acceptable reproducibility. If the percentage of paired measurements with acceptable reproducibility for a constituent was greater than or equal to 90 percent, then the reproducibility for that constituent was considered acceptable. The percentage of paired measurements with acceptable reproducibility was greater than or equal to 90 percent for all constituents except orthophosphate (89 percent), zinc (80 percent), hexavalent chromium (53 percent), and total organic carbon (TOC; 38 percent). The low reproducibility for orthophosphate and zinc was attributed to calculation of RSDs for replicates with low concentrations of these constituents. The low reproducibility for hexavalent chromium and TOC was attributed to the inability to preserve hexavalent chromium in water samples and high variability with the analytical method for TOC. The reliability of measurements of constituents was estimated from pooled RSDs that were calculated for discrete concentration ranges for each constituent. Pooled RSDs of 15 to 33 percent were calculated for low concentrations of gross-beta radioactivity, strontium-90, ammonia, nitrite, orthophosphate, nickel, selenium, zinc, tetrachloroethene, and toluene. Lower pooled RSDs of 0 to 12 percent were calculated for all other concentration ranges of these constituents, and for all other constituents, except for one concentration range for gross-beta radioactivity, chloride, and nitrate + nitrite; two concentration ranges for hexavalent chromium; and TOC. Pooled RSDs for the 50 to 60 picocuries per liter concentration range of gross-beta radioactivity (reported as cesium-137) and the 10 to 60 milligrams per liter (mg/L) concentration range of nitrate + nitrite (reported as nitrogen [N]) were 17 percent. Chloride had a pooled RSD of 14 percent for the 20 to less than 60 mg/L concentration range. High pooled RSDs of 40 and 51 percent were calculated for two concentration ranges for hexavalent chromium and of 60 percent for TOC. Measurements from (1) field blanks were used to estimate the potential bias associated with environmental samples from sample collection and analysis, (2) equipment blanks were used to estimate the potential bias from cross contamination of samples collected from wells where portable sampling equipment was used, and (3) a source-solution blank was used to verify that the deionized water source-solution was free of the constituents of interest. If more than one measurement was available, the bias was estimated using order statistics and the binomial probability distribution. The source-solution blank had a detectable concentration of hexavalent chromium of 2 micrograms per liter. If this bias was from a source other than the source solution, then about 84 percent of the 117 hexavalent chromium measurements from environmental samples could have a bias of 10 percent or more. Of the 14 field blanks that were collected, only chloride (0.2 milligrams per liter) and ammonia (0.03 milligrams per liter as nitrogen), in one blank each, had detectable concentrations. With an estimated confidencelevel of 95 percent, at least 80 percent of the 1,987 chloride concentrations measured from all environmental samples had a potential bias of less than 8 percent. The ammonia bias, which may have occurred at the analytical laboratory, could produce a potential bias of 5-100 percent in eight potentially affected ammonia measurements. Of the 11 equipment blanks that were collected, chloride was detected in 4 of these blanks, sodium in 3 blanks, and sulfate and hexavalent chromium were each detected in 1 blank. The concentration of hexavalent chromium in the equipment blank was the same concentration as in the source-solution blank collected on the same day, which indicates that the hexavalent chromium in the equipment blank is probably from a source other than the portable sampling equipment, such as the sample bottles or the source-solution water itself. The potential bias for chloride, sodium, and sulfate measurements was estimated for environmental samples that were collected using portable sampling equipment. For chloride, it was estimated with 93 percent confidence that at least 80 percent of the measurements had a bias of less than 18 percent. For sodium and sulfate, it was estimated with 91 percent confidence that at least 70 percent of the measurements had a bias of less than 12 and 5 percent, respectively.

The Fiscal Blank Check Policy and Its Impact on Operation Iraqi Freedom

DTIC Science & Technology

2006-12-01

facilities across Iraq has a significant logistical and financial tail associated with it. The increase in food and beverages (to the point of luxuries) has...THIS PAGE INTENTIONALLY LEFT BLANK v ABSTRACT Congress passed declaration of war language for World Wars I and...78 V . CONCLUSION AND RECOMMENDATIONS

Intellectual Property Rights for Digital Design and Manufacturing: Issues and Recommendations

DTIC Science & Technology

2014-06-30

for Public Release, Distribution Unlimited. iv This page intentionally left blank. Distribution A: Approved for...Distribution A: Approved for Public Release, Distribution Unlimited. viii This page intentionally left blank...challenges requires an analysis of intellectual property management and recommendations for its use in a cooperative as well as competitive market

Organizational Strategic Planning and Execution: Should Governmental Organizations Rely on Strategic Planning for the Success of the Organization?

DTIC Science & Technology

2007-06-01

THIS PAGE INTENTIONALLY LEFT BLANK i NSN 7540-01-280-5500 Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18...4 I . INTRODUCTION............................................................................................. 7 A. SCOPE...6 THIS PAGE INTENTIONALLY LEFT BLANK 7 I . INTRODUCTION A. SCOPE The intent

Strong Vocational Interest Blank Scores for Junior College Students in Five Curricula.

ERIC Educational Resources Information Center

Smith, Stuart E.

An investigation was conducted to determine if students in five junior college curricula could be differentiated by the Strong Vocational Interest Blank (SVIB) scores and if such differentiation could be improved by using several scores in combination rather than single scores separately. The SVIB was administered to 130 students at Alfred…

75 FR 9436 - Aleris Blanking and Rim Products, Inc., a Division of Aleris International, Inc., Terre Haute, IN...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-02

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-72,041] Aleris Blanking and Rim Products, Inc., a Division of Aleris International, Inc., Terre Haute, IN; Notice of Affirmative Determination Regarding Application for Reconsideration By application dated January 29, 2010, the petitioner...

Basin F Overburden and Soil Sampling and Analysis Study, Rocky Mountain Arsenal

DTIC Science & Technology

1982-05-01

boring sites will be es:ablished via standard :and surveyinS procedures. 3.3 Bor-ng/ Samaling Procidures Upon staking/marking of the bore holes, the folloi...procedure until the interferences have been eliminated. 3.2.2 Samale Testing Step OC (6) (Procedure Blank) The procedure blank consists of the

47 CFR 73.642 - Subscription TV service.

Code of Federal Regulations, 2011 CFR

2011-10-01

... available to the FCC upon request. (d) The use of the visual vertical blanking interval or an aural... programming may be used only upon specific FCC authorization. Letter requests to use either the video blanking intervals or aural subcarriers during periods of non-subscription programming are to be sent to the FCC in...

47 CFR 73.642 - Subscription TV service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... available to the FCC upon request. (d) The use of the visual vertical blanking interval or an aural... programming may be used only upon specific FCC authorization. Letter requests to use either the video blanking intervals or aural subcarriers during periods of non-subscription programming are to be sent to the FCC in...

Experimental Validation for Hot Stamping Process by Using Taguchi Method

NASA Astrophysics Data System (ADS)

Fawzi Zamri, Mohd; Lim, Syh Kai; Razlan Yusoff, Ahmad

2016-02-01

Due to the demand for reduction in gas emissions, energy saving and producing safer vehicles has driven the development of Ultra High Strength Steel (UHSS) material. To strengthen UHSS material such as boron steel, it needed to undergo a process of hot stamping for heating at certain temperature and time. In this paper, Taguchi method is applied to determine the appropriate parameter of thickness, heating temperature and heating time to achieve optimum strength of boron steel. The experiment is conducted by using flat square shape of hot stamping tool with tensile dog bone as a blank product. Then, the value of tensile strength and hardness is measured as response. The results showed that the lower thickness, higher heating temperature and heating time give the higher strength and hardness for the final product. In conclusion, boron steel blank are able to achieve up to 1200 MPa tensile strength and 650 HV of hardness.

[Danger from exploding fireworks and blank firearms].

PubMed

Just, T; Pau, H W; Kaduk, W; Hingst, V

2000-12-01

Explosive amusement and deterrent articles such as New Year's Eve cannons and rockets, toy pistols, and blank guns are not at all harmless items. Their potential dangerousness is often extremely underestimated. Two damaging mechanisms are important: during explosions, high pressures and temperatures develop and a considerable sound pressure level can be measured. If the explosion happens near the human body (intentionally or inadvertently), not only superficial lesions can occur, but also (mainly due to contact shots) serious, deep-seated tissue damage, especially in the head and neck region with its endangered sense organs such as eye and ear, the vessels and nerves supplying the brain, the speech- and voice-forming apparatus, and in particular the face, can be the consequence. Their mutilation can lead to serious and extensive interpersonalchanges. Accidents are published in the relevant otological and forensic medical papers, but nevertheless it seems important to us to point out the dangerousness of these readily available items.

Predetermined Flake Production at the Lower/Middle Paleolithic Boundary: Yabrudian Scraper-Blank Technology

PubMed Central

Shimelmitz, Ron; Kuhn, Steven L.; Ronen, Avraham; Weinstein-Evron, Mina

2014-01-01

While predetermined débitage technologies are recognized beginning with the middle Acheulian, the Middle Paleolithic is usually associated with a sharp increase in their use. A study of scraper-blank technology from three Yabrudian assemblages retrieved from the early part of the Acheulo-Yabrudian complex of Tabun Cave (ca. 415–320 kyr) demonstrates a calculated and preplanned production, even if it does not show the same complexity and elaboration as in the Levallois technology. These scraper dominated assemblages show an organization of production based on an intensive use of predetermination blank technology already in place at the end of the Lower Paleolithic of the Levant. These results provide a novel perspective on the differences and similarities between the Lower and Middle Paleolithic industries. We suggest that there was a change in the paradigm in the way hominins exploited stone tools: in many Middle Paleolithic assemblages the potential of the stone tools for hafting was a central feature, in the Lower Paleolithic ergonometric considerations of manual prehension were central to the design of blanks and tools. PMID:25192429

Gaze differences in processing pictures with emotional content.

PubMed

Budimir, Sanja; Palmović, Marijan

2011-01-01

The International Affective Picture System (IAPS) is a set of standardized emotionally evocative color photographs developed by NIMH Center for Emotion and Attention at the University of Florida. It contains more than 900 emotional pictures indexed by emotional valence, arousal and dominance. However, when IAPS pictures were used in studying emotions with the event-related potentials, the results have shown a great deal of variation and inconsistency. In this research arousal and dominance of pictures were controlled while emotional valence was manipulated as 3 categories, pleasant, neutral and unpleasant pictures. Two experiments were conducted with an eye-tracker in order to determine to what the participants turn their gaze. Participants were 25 psychology students with normal vision. Every participant saw all pictures in color and same pictures in black/white version. This makes 200 analyzed units for color pictures and 200 for black and white pictures. Every picture was divided into figure and ground. Considering that perception can be influenced by color, edges, luminosity and contrast and since all those factors are collapsed on the pictures in IAPS, we compared color pictures with same black and white pictures. In first eye-tracking IAPS research we analyzed 12 emotional pictures and showed that participants have higher number of fixations for ground on neutral and unpleasant pictures and for figure on pleasant pictures. Second experiment was conducted with 4 sets of emotional complementary pictures (pleasant/unpleasant) which differ only on the content in the figure area and it was shown that participants were more focused on the figure area than on the ground area. Future ERP (event related potential) research with IAPS pictures should take into consideration these findings and to either choose pictures with blank ground or adjust pictures in the way that ground is blank. For the following experiments suggestion is to put emotional content in the figure area and to use different non complementary pictures to see if there is difference between different emotional categories.

UDOF direct improvement by modulating mask absorber thickness

NASA Astrophysics Data System (ADS)

Yu, Tuan-Yen; Lio, En Chuan; Chen, Po Tsang; Wei, Chih I.; Chen, Yi Ting; Peng, Ming Chun; Chou, William; Yu, Chun Chi

2016-10-01

As the process generation migrate to advanced and smaller dimension or pitch, the mask and resist 3D effects will impact the lithography focus common window severely because of both individual depth-of-focus (iDOF) range decrease and center mismatch. Furthermore, some chemical or thermal factors, such as PEB (Post Exposure Bake) also worsen the usable depth-of-focus (uDOF) performance. So the mismatch of thru-pitch iDOF center should be considered as a lithography process integration issue, and more complicated to partition the 3D effects induced by optical or chemical factors. In order to reduce the impact of 3D effects induced by both optical and chemical issues, and improve iDOF center mismatch, we would like to propose a mask absorber thickness offset approach, which is directly to compensate the iDOF center bias by adjusting mask absorber thickness, for iso, semi-iso or dense characteristics in line, space or via patterns to enlarge common process window, i.e uDOF, which intends to provide similar application as Flexwave[1] (ASML trademark). By the way, since mask absorber thickness offset approach is similar to focus tuning or change on wafer lithography process, it could be acted as the process tuning method of photoresist (PR) profile optimization locally, PR scum improvement in specific patterns or to modulate etching bias to meet process integration request. For mass production consideration, and available material, current att-PSM blank, quartz, MoSi with chrome layer as hard-mask in reticle process, will be implemented in this experiment, i.e. chrome will be kept remaining above partial thru-pitch patterns, and act as the absorber thickness bias in different patterns. And then, from the best focus offset of thru-pitch patterns, the iDOF center shifts could be directly corrected and to enlarge uDOF by increasing the overlap of iDOF. Finally, some negative tone development (NTD) result in line patterns will be demonstrated as well.

Computer Aided Process Planning for Non-Axisymmetric Deep Drawing Products

NASA Astrophysics Data System (ADS)

Park, Dong Hwan; Yarlagadda, Prasad K. D. V.

2004-06-01

In general, deep drawing products have various cross-section shapes such as cylindrical, rectangular and non-axisymmetric shapes. The application of the surface area calculation to non-axisymmetric deep drawing process has not been published yet. In this research, a surface area calculation for non-axisymmetric deep drawing products with elliptical shape was constructed for a design of blank shape of deep drawing products by using an AutoLISP function of AutoCAD software. A computer-aided process planning (CAPP) system for rotationally symmetric deep drawing products has been developed. However, the application of the system to non-axisymmetric components has not been reported yet. Thus, the CAPP system for non-axisymmetric deep drawing products with elliptical shape was constructed by using process sequence design. The system developed in this work consists of four modules. The first is recognition of shape module to recognize non-axisymmetric products. The second is a three-dimensional (3-D) modeling module to calculate the surface area for non-axisymmetric products. The third is a blank design module to create an oval-shaped blank with the identical surface area. The forth is a process planning module based on the production rules that play the best important role in an expert system for manufacturing. The production rules are generated and upgraded by interviewing field engineers. Especially, the drawing coefficient, the punch and die radii for elliptical shape products are considered as main design parameters. The suitability of this system was verified by applying to a real deep drawing product. This CAPP system constructed would be very useful to reduce lead-time for manufacturing and improve an accuracy of products.

Foil Gas Thrust Bearings for High-Speed Turbomachinery

NASA Technical Reports Server (NTRS)

Edmonds, Brian; DellaCorte, Christopher; Dykas, Brian

2010-01-01

A methodology has been developed for the design and construction of simple foil thrust bearings intended for parametric performance testing and low marginal costs, supporting continued development of oil-free turbomachinery. A bearing backing plate is first machined and surface-ground to produce flat and parallel faces. Partial-arc slots needed to retain the foil components are then machined into the plate by wire electrical discharge machining. Slot thicknesses achievable by a single wire pass are appropriate to accommodate the practical range of foil thicknesses, leaving a small clearance in this hinged joint to permit limited motion. The backing plate is constructed from a nickel-based superalloy (Inconel 718) to allow heat treatment of the entire assembled bearing, as well as to permit hightemperature operation. However, other dimensionally stable materials, such as precipitation-hardened stainless steel, can also be used for this component depending on application. The top and bump foil blanks are cut from stacks of annealed Inconel X-750 foil by the same EDM process. The bump foil has several azimuthal slits separating it into five individual bump strips. This configuration allows for variable bump spacing, which helps to accommodate the effects of the varying surface velocity, thermal crowning, centrifugal dishing, and misalignment. Rectangular tabs on the foil blanks fit into the backing plate slots. For this application, a rather traditional set of conventionally machined dies is selected, and bump foil blanks are pressed into the dies for forming. This arrangement produces a set of bump foil dies for foil thrust bearings that provide for relatively inexpensive fabrication of various bump configurations, and employing methods and features from the public domain.

Pencil-Free Homework: Worth Considering?

ERIC Educational Resources Information Center

Forster, Colin

2016-01-01

After spending most of the day in school, children are typically given additional assignments to be completed at home. The author and colleagues developed a series of science homework tasks for use in primary schools. The difference with these homework tasks, however, was that they were pencil-free: no blank spaces for the children to fill in and…

New Developments in 1,4 Dioxane Site Management

DTIC Science & Technology

2016-11-01

oxidation, enhanced bioremediation , site management. Unclassified Unclassified UU UL 8 David Adamson (713) 522-6300 Page Intentionally Left Blank...there was little indication that chlorinated solvent remedial efforts (e.g., chemical oxidation, enhanced bioremediation ) impacted 1,4-dioxane...oxidation may prove beneficial for subsequent biologically- based approaches, including both enhanced bioremediation and natural attenuation. FOR

Dogs can discriminate human smiling faces from blank expressions.

PubMed

Nagasawa, Miho; Murai, Kensuke; Mogi, Kazutaka; Kikusui, Takefumi

2011-07-01

Dogs have a unique ability to understand visual cues from humans. We investigated whether dogs can discriminate between human facial expressions. Photographs of human faces were used to test nine pet dogs in two-choice discrimination tasks. The training phases involved each dog learning to discriminate between a set of photographs of their owner's smiling and blank face. Of the nine dogs, five fulfilled these criteria and were selected for test sessions. In the test phase, 10 sets of photographs of the owner's smiling and blank face, which had previously not been seen by the dog, were presented. The dogs selected the owner's smiling face significantly more often than expected by chance. In subsequent tests, 10 sets of smiling and blank face photographs of 20 persons unfamiliar to the dogs were presented (10 males and 10 females). There was no statistical difference between the accuracy in the case of the owners and that in the case of unfamiliar persons with the same gender as the owner. However, the accuracy was significantly lower in the case of unfamiliar persons of the opposite gender to that of the owner, than with the owners themselves. These results suggest that dogs can learn to discriminate human smiling faces from blank faces by looking at photographs. Although it remains unclear whether dogs have human-like systems for visual processing of human facial expressions, the ability to learn to discriminate human facial expressions may have helped dogs adapt to human society.

The toxicity potential of pharmaceuticals found in the Douro River estuary (Portugal)--experimental assessment using a zebrafish embryo test.

PubMed

Madureira, Tânia Vieira; Cruzeiro, Catarina; Rocha, Maria João; Rocha, Eduardo

2011-09-01

Fish embryos are a particularly vulnerable stage of development, so they represent optimal targets for screening toxicological effects of waterborne xenobiotics. Herein, the toxicity potential of two mixtures of pharmaceuticals was evaluated using a zebrafish embryo test. One of the mixtures corresponds to an environmentally realistic scenario and both have carbamazepine, fenofibric acid, propranolol, trimethoprim and sulfamethoxazole. The results evidenced morphological alterations, such as spinal deformities and yolk-sac oedemas. Moreover, heart rates decreased after both mixture exposures, e.g., at 48hpf, highest mixture versus blank control (47.8±4.9 and 55.8±3.7 beats/30s, respectively). The tail lengths also diminished significantly from 3208±145μm in blank control to 3130±126μm in highest mixture. The toxicological effects were concentration dependent. Mortality, hatching rate and the number of spontaneous movements were not affected. However, the low levels of pharmaceuticals did interfere with the normal development of zebrafish, which indicates risks for wild organisms. Copyright © 2011 Elsevier B.V. All rights reserved.

EUVL Mask Blank Repair

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barty, A; Mirkarimi, P; Stearns, D G

2002-05-22

EUV mask blanks are fabricated by depositing a reflective Mo/Si multilayer film onto super-polished substrates. Small defects in this thin film coating can significantly alter the reflected field and introduce defects in the printed image. Ideally one would want to produce defect-free mask blanks; however, this may be very difficult to achieve in practice. One practical way to increase the yield of mask blanks is to effectively repair multilayer defects, and to this effect they present two complementary defect repair strategies for use on multilayer-coated EUVL mask blanks. A defect is any area on the mask which causes unwanted variationsmore » in EUV dose in the aerial image obtained in a printing tool, and defect repair is correspondingly defined as any strategy that renders a defect unprintable during exposure. The term defect mitigation can be adopted to describe any strategy which renders a critical defect non-critical when printed, and in this regard a non-critical defect is one that does not adversely affect device function. Defects in the patterned absorber layer consist of regions where metal, typically chrome, is unintentionally added or removed from the pattern leading to errors in the reflected field. There currently exists a mature technology based on ion beam milling and ion beam assisted deposition for repairing defects in the absorber layer of transmission lithography masks, and it is reasonable to expect that this technology will be extended to the repair of absorber defects in EUVL masks. However, techniques designed for the repair of absorber layers can not be directly applied to the repair of defects in the mask blank, and in particular the multilayer film. In this paper they present for the first time a new technique for the repair of amplitude defects as well as recent results on the repair of phase defects.« less

Skill Transfer and Virtual Training for IND Response Decision-Making: Models for Government-Industry Collaboration for the Development of Game-Based Training Tools

DTIC Science & Technology

2016-05-05

Training for IND Response Decision-Making: Models for Government–Industry Collaboration for the Development of Game -Based Training Tools R.M. Seater...Skill Transfer and Virtual Training for IND Response Decision-Making: Models for Government–Industry Collaboration for the Development of Game -Based...unlimited. This page intentionally left blank. iii EXECUTIVE SUMMARY Game -based training tools, sometimes called “serious games ,” are becoming

The study on specific umbilical blood Dc vaccine for Beige nude mice loaded human colorectal carcinoma to induce anti-tumor immunity.

PubMed

Fu, Z-X; Han, J-S; Liu, F; Zhao, Z-L; Li, D-B; Shi, L; Dong, J-T; Zhou, Y; Cai, J-H

2017-05-01

This study is to observe the immunosuppression of CD137L transfected umbilical blood Dcs (Dendritic cell) vaccine to tumor development of SCID/ Beige nude mice. Samples of umbilical blood in the childbirth pregnant women were collected by density gradient centrifugation. Umbilical cord blood dendritic cells (Dcs) were transfected by specific CD137L via LipofectamineTM method and cells were harvested. Meanwhile, the peripheral blood of volunteers was collected to isolate Dcs, the Dcs were cultured for 5 days and hatched with SW-1116 cells antigen. The mature Dcs were harvested. The male SCID/Beige nude mice were subcutaneously injected with human SW-1116 cells in axillary to build colorectal carcinoma model as blank control (Blank). The naked peripheral blood Dc vaccine group (cPBMCs), the SW-1116 antigen-specific peripheral blood Dc vaccine group (pDcs) and the CD137L specific umbilical blood Dc vaccine group (tuDcs) were injected 24 h before tumor cells injection, respectively to recur the humanized immune reconstruction. The general life, living habits changes, tumor growing time and tumor size were observed. The nude mice were sacrificed 18 days after tumor formation. The tumor size, mice weight, in vitro tumor weight, liver weight and spleen weight of mice were recorded to evaluate the anti-tumor effect of the specific immune cells. The nude mice in pDcs group showed better general living condition, slower tumor growth, smaller tumor volume and no ulceration, necrosis, and death in nude mice. The tumor formation time in different groups was 4.71 ± 0.18 ds (blank), 7.71 ± 0.29 ds (cPBMCs), 7.86 ± 0.26 ds (pDcs) and 8.14 ± 0.69 ds (tuDcs) respectively. There were significant differences between blank and other three groups (F = 40.96, p < 0.01). Compared to mice in blank group, the tumor volume of cPBMCs group was significantly smaller (201.43 ± 69.84 mm³ vs. 436.04 ± 54.50 mm³, p < 0.01) and the tumor weight were significantly smaller (1.25 ± 0.12 g vs. 2.83 ± 0.24 g, p < 0.01). The tumor volume of tuDcs mice was significantly smaller than that of blank (92.11 ± 11.55 mm³ vs. 436.04 ± 54.50 mm³, p < 0.01) and cPBMCs mice (92.11 ± 11.55 mm³ vs. 201.43 ± 69.84 mm³, p < 0.01). Similarly, the tumor weight of tuDcs mice was significantly smaller than that of blank (0.66 ± 0.07 g vs. 2.83 ± 0.24 g, p < 0.01) and cPBMCs mice (0.66 ± 0.07 g vs. 1.25 ± 0.12 g, p < 0.01). There was no significant difference in tumor volume (92.11 ± 11.55 mm³ vs. 85.61 ± 11.59 mm³, p = 0.69) and tumor weight (0.66 ± 0.07 g vs. 0.63 ± 0.09 g, p = 0.75) between tuDcs group and pDcs group. The specific CD137L transfected umbilical blood Dc vaccine had significant anti-tumor effect against human colon cancer in nude mice via increasing the number of immune effector cell in tumor microenvironment.

Determination of Natural 14C Abundances in Dissolved Organic Carbon in Organic-Rich Marine Sediment Porewaters by Thermal Sulfate Reduction

NASA Astrophysics Data System (ADS)

Johnson, L.; Komada, T.

2010-12-01

The abundances of natural 14C in dissolved organic carbon (DOC) in the marine environment hold clues regarding the processes that influence the biogeochemical cycling of this large carbon reservoir. At present, UV irradiation is the widely accepted method for oxidizing seawater DOC for determination of their 14C abundances. This technique yields precise and accurate values with low blanks, but it requires a dedicated vacuum line, and hence can be difficult to implement. As an alternative technique that can be conducted on a standard preparatory vacuum line, we modified and tested a thermal sulfate reduction method that was previously developed to determine δ13C values of marine DOC (Fry B. et al., 1996. Analysis of marine DOC using a dry combustion method. Mar. Chem., 54: 191-201.) to determine the 14C abundances of DOC in marine sediment porewaters. In this method, the sample is dried in a 100 ml round-bottom Pyrex flask in the presence of excess oxidant (K2SO4) and acid (H3PO4), and combusted at 550 deg.C. The combustion products are cryogenically processed to collect and quantify CO2 using standard procedures. Materials we have oxidized to date range from 6-24 ml in volume, and 95-1500 μgC in size. The oxidation efficiency of this method was tested by processing known amounts of reagent-grade dextrose and sucrose (as examples of labile organic matter), tannic acid and humic acid (as examples of complex natural organic matter), and porewater DOC extracted from organic-rich nearshore sediments. The carbon yields for all of these materials averaged 99±4% (n=18). The 14C abundances of standard materials IAEA C-6 and IAEA C-5 processed by this method using >1mgC aliquots were within error of certified values. The size and the isotopic value of the blank were determined by a standard dilution technique using IAEA C-6 and IAEA C-5 that ranged in size from 150 to 1500 μgC (n=4 and 2, respectively). This yielded a blank size of 6.7±0.7 μgC, and a blank isotopic value of 0.54±0.05 fMC. The size of the blank agreed well with that determined directly by processing variable volumes of UV-irradiated deionized water (5.6±0.7 μgC, n=9). The size of the blank amounts to <~5% of the size of porewater DOC samples that are typically recovered from organic-rich sediment cores (~100-500 μgC). The fMC value of the blank suggests that there may be multiple sources of extraneous carbon that range in 14C abundance. In order to assess the fidelity of 14C abundances in natural porewater DOC oxidized by thermal sulfate reduction, we oxidized porewater DOC samples collected from the central floor of the Santa Monica Basin, California Borderland, using both this method and UV irradiation (the latter carried out at the Druffel laboratory, University of California Irvine). The fMC values obtained by the two methods agreed within error. Carbon yields from the two methods also agreed closely. These findings show that thermal sulfate reduction may be a promising method to oxidize small, concentrated marine DOC samples for 14C analysis.

The enkephalinergic nervous system and its immunomodulation on the developing immune system during the ontogenesis of oyster Crassostrea gigas.

PubMed

Liu, Zhaoqun; Zhou, Zhi; Wang, Lingling; Song, Xiaorui; Chen, Hao; Wang, Weilin; Liu, Rui; Wang, Mengqiang; Wang, Hao; Song, Linsheng

2015-08-01

Enkephalinergic neuroendocrine-immune regulatory system is one of the most important neuroendocrine-immune systems in both vertebrates and invertebrates for its significant role in the immune regulation. In the present study, the early onset of enkephalinergic nervous system and its immunomodulation on the developing immune system during the ontogenesis of oyster Crassostrea gigas were investigated to illustrate the function of neural regulation on the innate immune system in oyster larvae. [Met(5)]-enkephalin (Met-ENK) was firstly observed on the marginal of the dorsal half of D-hinged larvae. Six immune-related molecules, including four PRRs (CgCTL-1, CgCTL-2, CgCTL-4, CgNatterin-3) and two immune effectors (CgTNF-1 and CgEcSOD) were detected in the early developmental stages of trochophore, D-hinged and umbo larvae of oyster. After incubated with [Met(5)]-enkephalin, the mRNA expression level of all the PRRs changed significantly (p < 0.05). In trochophore larvae, the expression level of CgNatterin-3 decreased dramatically (p < 0.05) at 6 h, and the expression level of CgCTL-4 was significantly down-regulated at 3 h and 6 h (p < 0.05), respectively. In D-hinged and umbo larvae, only CgCTL-1 was significantly down-regulated and the differences were significant at 3 h and 6 h (p < 0.05), while the expression level of CgCTL-2 and CgCTL-4 increased significantly at 3 h after treatment (p < 0.05). Moreover, the expression levels of immune effectors were up-regulated significantly at 3 h and 6 h in trochophore larvae (p < 0.05). The expression level of CgTNF-1 in both blank and experiment groups was up-regulated but there was no significant difference in D-hinged larvae stage. On the contrary, the expression level of CgEcSOD in D-hinged larvae decreased dramatically at 3 h and 6 h after [Met(5)]-enkephalin incubation (p < 0.05). In umbo larvae, the expression level of CgTNF-1 and CgEcSOD in the experiment group increased significantly at 6 h after [Met(5)]-enkephalin treatment (p < 0.05), while no significant difference was found in the blank group. In addition, the anti-bacterial activities of the total protein extract from trochophore, D-hinged and umbo larvae increased significantly (p < 0.05) at both 3 h and 6 h after [Met(5)]-enkephalin incubation compared to that in the blank group, and PO activities of both D-hinged and umbo larvae total protein extract increased significantly (p < 0.05) while no significant difference was observed in trochophore larvae. The PO activities of the total protein extract in all the experiment groups decreased after the treatment with [Met(5)]-enkephalin for 6 h, but no significant difference was observed when compared to the blank group. Furthermore, after incubation for 6 h, the concentration of both CgTNF-1 and CgIL17-5 increased dramatically compared to that in the blank group (p < 0.05). These results together indicated that the enkephalinergic nervous system of oyster was firstly appeared in D-hinged larvae, while the primitive immune defense system existed in the region of prototroch in trochophore larvae and developed maturely after D-hinged larvae. The developing immune system could be regulated by the neurotransmitter [Met(5)]-enkephalin released by the neuroendocrine system in oyster C. gigas. Copyright © 2015 Elsevier Ltd. All rights reserved.

47 CFR 73.646 - Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Blanking Interval and in the Visual Signal. 73.646 Section 73.646 Telecommunication FEDERAL COMMUNICATIONS... transmission of data, processed information, or any other communication in either a digital or analog mode. (b... kinds of service that may be provided include, but are not limited to, teletext, paging, computer...

47 CFR 73.646 - Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Blanking Interval and in the Visual Signal. 73.646 Section 73.646 Telecommunication FEDERAL COMMUNICATIONS... transmission of data, processed information, or any other communication in either a digital or analog mode. (b... kinds of service that may be provided include, but are not limited to, teletext, paging, computer...

47 CFR 73.646 - Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Blanking Interval and in the Visual Signal. 73.646 Section 73.646 Telecommunication FEDERAL COMMUNICATIONS... transmission of data, processed information, or any other communication in either a digital or analog mode. (b... kinds of service that may be provided include, but are not limited to, teletext, paging, computer...

47 CFR 73.646 - Telecommunications Service on the Vertical Blanking Interval and in the Visual Signal.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Blanking Interval and in the Visual Signal. 73.646 Section 73.646 Telecommunication FEDERAL COMMUNICATIONS... transmission of data, processed information, or any other communication in either a digital or analog mode. (b... kinds of service that may be provided include, but are not limited to, teletext, paging, computer...

U.S. Foreign Policy’s Role in Homeland Security: The Egyptian Case

DTIC Science & Technology

2011-12-01

Robert E. Looney THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting burden for this...CONTENTS I . INTRODUCTION........................................................................................................1 A. MAJOR RESEARCH...PAGE INTENTIONALLY LEFT BLANK xi ACKNOWLEDGMENTS I would like to thank Dr. Abbas Kadhim and Dr. Robert Looney for their support, expertise, and

A big blank white canvas? Mapping and modeling human impact in Antarctica

Treesearch

Steve Carver; Tina Tin

2015-01-01

Antarctica is certainly what most people would consider being the world's last great wilderness; largely untouched and undeveloped by humans. Yet it is not inviolate - there are scientific bases, tourist operations, expeditions, airstrips and even roads. Although these impacts are by and large limited in extent, their very presence in an otherwise "blank...

The Disposition of Topically Applied Agents

DTIC Science & Technology

1981-09-24

S . op . cit. 28. Scheuplein R.J., Blank I.H. op. cit. 29. Lorenzetti O.J. Cosmet. Toil. 93_:49-50, 1978. 30. Scheuplein R.J., Blank I.H. op. cit...Riegelman S . op . cit. 37. Wester R. , Noonan P J. invest. Derm. 72:92-94, 1978. 38. Mansel-Jones D., Taylor T., Doyle E., Chasseud L.F., Darraugh A

Optimal Number of Gaps in C-Test Passages

ERIC Educational Resources Information Center

Baghaei, Purya

2011-01-01

This study addresses the issue of the optimal number of gaps in C-Test passages. An English C-Test battery containing four passages each having 40 blanks was given to 104 undergraduate students of English. The data were entered into SPSS spreadsheet. Out of the complete data with 160 blanks seven additional datasets were constructed. In the first…

The Use of Application Blanks as Pre-Screening Devices in Employee Selection: An Assessment of Practices in Public Schools.

ERIC Educational Resources Information Center

Bredeson, Paul V.

1988-01-01

Reports on a study of the use of employment application blanks as prescreening devices in public school employee selection. Findings suggest two major areas for further research. The first relates to legal compliance with Equal Opportunity Employment guidelines. The second concerns information relevancy to personnel selection. (JAM)

Meeting the Solid Wood Needs of the Furniture and Cabinet Industries: Standard-Size Hardwood Blanks

Treesearch

Philip A. Araman; Charles J Gatchell; Hugh W. Reynolds

1982-01-01

Standard-size, kiln-dried hardwood blanks (panels) of specified lengths, widths, thicknesses, and qualities can be used instead of lumber to produce rough dimension furniture parts. Standard sizes were determined by analyzing thousands of part requirements from 20 furniture and 12 kitchen cabinet companies. The International Woodworking Machinery and Furniture Supply...

System 6 alternatives: an economic analysis

Treesearch

Bruce G. Hansen; Hugh W. Reynolds; Hugh W. Reynolds

1984-01-01

Three System 6 mill-size alternatives were designed and evaluated to determine their overall economic potential for producing standard-size hardwood blanks. Internal rates of return ranged from about 15 to 35 percent after taxes. Cost per square foot of blanks ranged from about $0.88 to $1.19, depending on mill size and the amount of new investment required.

Production of EUV mask blanks with low killer defects

NASA Astrophysics Data System (ADS)

Antohe, Alin O.; Kearney, Patrick; Godwin, Milton; He, Long; John Kadaksham, Arun; Goodwin, Frank; Weaver, Al; Hayes, Alan; Trigg, Steve

2014-04-01

For full commercialization, extreme ultraviolet lithography (EUVL) technology requires the availability of EUV mask blanks that are free of defects. This remains one of the main impediments to the implementation of EUV at the 22 nm node and beyond. Consensus is building that a few small defects can be mitigated during mask patterning, but defects over 100 nm (SiO2 equivalent) in size are considered potential "killer" defects or defects large enough that the mask blank would not be usable. The current defect performance of the ion beam sputter deposition (IBD) tool will be discussed and the progress achieved to date in the reduction of large size defects will be summarized, including a description of the main sources of defects and their composition.

Actinic defect counting statistics over 1-cm2 area of EUVL mask blank

NASA Astrophysics Data System (ADS)

Jeong, Seongtae; Lai, Chih-wei; Rekawa, Senajith; Walton, Christopher C.; Bokor, Jeffrey

2000-07-01

As a continuation of comparison experiments between EUV inspection and visible inspection of defects on EUVL mask blanks, we report on the result of an experiment where the EUV defect inspection tool is used to perform at-wavelength defect counting over 1 cm2 of EUVL mask blank. Initial EUV inspection found five defects over the scanned area and the subsequent optical scattering inspection was able to detect all of the five defects. Therefore, if there are any defects that are only detectable by EUV inspection, the density is lower than the order of unity per cm2. An upgrade path to substantially increase the overall throughput of the EUV inspection system is also identified in the manuscript.

Formability analysis of austenitic stainless steel-304 under warm conditions

NASA Astrophysics Data System (ADS)

Lade, Jayahari; Singh, Swadesh Kumar; Banoth, Balu Naik; Gupta, Amit Kumar

2013-12-01

A warm deep drawing process of austenitic stainless steel-304 (ASS-304) of circular blanks with coupled ther mal analysis is studied in this article. 65 mm blanks were deep drawn at different temperatures and thickness distribution is experimentally measured after cutting the drawn component into two halves. The process is simulated using explicit fin ite element code LS-DYNA. A Barlat 3 parameter model is used in the simulation, as the material is anisotropic up to 30 0°C. Material properties for the simulation are determined at different temperatures using a 5 T UTM coupled with a furn ace. In this analysis constant punch speed and variable blank holder force (BHF) is applied to draw cups without wrinkle.

Influence of asymmetrical drawing radius deviation in micro deep drawing

NASA Astrophysics Data System (ADS)

Heinrich, L.; Kobayashi, H.; Shimizu, T.; Yang, M.; Vollertsen, F.

2017-09-01

Nowadays, an increasing demand for small metal parts in electronic and automotive industries can be observed. Deep drawing is a well-suited technology for the production of such parts due to its excellent qualities for mass production. However, the downscaling of the forming process leads to new challenges in tooling and process design, such as high relative deviation of tool geometry or blank displacement compared to the macro scale. FEM simulation has been a widely-used tool to investigate the influence of symmetrical process deviations as for instance a global variance of the drawing radius. This study shows a different approach that allows to determine the impact of asymmetrical process deviations on micro deep drawing. In this particular case the impact of an asymmetrical drawing radius deviation and blank displacement on cup geometry deviation was investigated for different drawing ratios by experiments and FEM simulation. It was found that both variations result in an increasing cup height deviation. Nevertheless, with increasing drawing ratio a constant drawing radius deviation has an increasing impact, while blank displacement results in a decreasing offset of the cups geometry. This is explained by different mechanisms that result in an uneven cup geometry. While blank displacement leads to material surplus on one side of the cup, an unsymmetrical radius deviation on the other hand generates uneven stretching of the cups wall. This is intensified for higher drawing ratios. It can be concluded that the effect of uneven radius geometry proves to be of major importance for the production of accurately shaped micro cups and cannot be compensated by intentional blank displacement.

The Effect of Guided Note Taking during Lectures on Thai University Students' Understanding of Electromagnetism

ERIC Educational Resources Information Center

Narjaikaew, Pattawan; Emarat, Narumon; Cowie, Bronwen

2009-01-01

This paper reports on the implementation of a guided note taking strategy to promote Thai students' understanding of electromagnetism during a lecture course. The aim of the study was to enhance student learning of electromagnetism concepts. The developed guided notes contain quotations, diagrams, pictures, problems, and blank spaces to encourage…

Application of Real Options Theory to DoD Software Acquisitions

DTIC Science & Technology

2009-08-01

words.) The traditional real options valuation methodology, when enhanced and properly formulated around a proposed or existing software investment...Std 239-18 - ii - THIS PAGE INTENTIONALLY LEFT BLANK - iii - Abstract The traditional real options valuation ...founder and CEO of Real Options Valuation , Inc., a consulting, training, and software development firm specializing in strategic real options

Application of Real Options Theory to DoD Software Acquisitions

DTIC Science & Technology

2009-02-20

Future Combat Systems Program. Washington, DC. U.S. Government Printing Office. Damodaran , A. (2007). Investment Valuation : The Options To Expand... valuation methodology, when enhanced and properly formulated around a proposed or existing software investment employing the spiral development approach...THIS PAGE INTENTIONALLY LEFT BLANK iii ABSTRACT The traditional real options valuation methodology, when enhanced and properly formulated

Improving Emergency Management by Modeling Ant Colonies

DTIC Science & Technology

2015-03-01

LEFT BLANK vii TABLE OF CONTENTS I.  THE INCIDENT COMMAND SYSTEM AND AUTONOMOUS ACTORS ......1  A.  PROBLEM STATEMENT...managerial level tasking.12 The Oklahoma City bombing has generally been viewed as a success for the ICS model; however, there were numerous occurrences...developed. The youngest generation of ant 25 Bert Holldobler and Edward O. Wilson, The Ants

Blank Canvas and Glass Ceiling: Using Visual Metaphors and Narratives to Examine Preservice Teacher Development

ERIC Educational Resources Information Center

Gosselin, Colette; Meixner, Emily

2015-01-01

When preparing college-age teacher candidates to teach in diverse contexts, knowing how they reconcile knowledge, self-author, and negotiate social relationships can enhance pedagogy and inform program design. In this article, the authors use a developmental framework they created to examine how teacher candidates' visual metaphors about White…

Development and Application of an Instrument to Identify Students Misconceptions: Diffusion and Osmosis

ERIC Educational Resources Information Center

Misischia, Cynthia M.

2010-01-01

A large number of undergraduate students have naive understandings about the processes of Diffusion and Osmosis. Some students overcome these misconceptions, but others do not. The study involved nineteen undergraduate movement science students at a Midwest University. Participants' were asked to complete a short answer (fill-in the blank) test,…

Outsourcing Wars: Comparing Risk, Benefits and Motivation of Contractors and Military Personnel in Iraq and Afghanistan (2009-2011)

DTIC Science & Technology

2012-06-01

Cary Simon Approved for public release; distribution is unlimited THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE...Advisor _____________________________________ Cary Simon, Support Advisor _____________________________________ William R...International Development xv ACKNOWLEDGMENTS Professor Kathryn Aten and Professor Cary Simon - I want to express my deepest gratitude to you for being

Skill Transfer and Virtual Training for IND Response Decision-Making: Models for Government-Industry Collaboration for the Development of Game-Based Training Tools

DTIC Science & Technology

2016-04-01

IND Response Decision-Making: Models for Government–Industry Collaboration for the Development of Game -Based Training Tools R.M. Seater C.E. Rose...Models for Government–Industry Collaboration for the Development of Game -Based Training Tools C.E. Rose A.S. Norige Group 44 R.M. Seater K.C...Report 1208 Lexington Massachusetts This page intentionally left blank. iii EXECUTIVE SUMMARY Game -based training tools, sometimes called “serious

Fighting Tomorrows Fire Today: Leveraging Intelligence for Scenario-Based Exercise Design

DTIC Science & Technology

2014-03-01

Management and Budget, Paperwork Reduction Project (0704–0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE March 2014 3...IPG Improvised Projected Grenade IT information technology LLIS Lessons Learned Information Sharing MEP Master Exercise Practitioner MOU...Disaster?” Natural Hazards 18, no. 1 (1998): 87–88. xvii THIS PAGE INTENTIONALLY LEFT BLANK xviii

A Decision Support Personnel Monitoring Database System Prototype for the United States Marine Corps.

DTIC Science & Technology

1985-12-19

Officer. The second space represents the current pay grade. The third space E indi- cates the officer has a least four years of enlisted active service...second space can only be 1-6. The third space can only be E or blank. Warrant Officers and PGRD 04 and above will have the third space blank even if

Information Operations in Pursuit of Terrorists

DTIC Science & Technology

2007-09-01

230 Blanking Out operations is a term used to somehow undertake partial and region-specific censorship ...4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2...to highlight the use of information operations by terrorist organizations and in particular its use by Al Qaeda. In order to compare the complete

Optimizing Marine Corps Personnel Assignments Using an Integer Programming Model

DTIC Science & Technology

2012-12-01

Corps. vi THIS PAGE INTENTIONALLY LEFT BLANK vii TABLE OF CONTENTS I. INTRODUCTION ...throughout our careers. xvi THIS PAGE INTENTIONALLY LEFT BLANK 1 I. INTRODUCTION The Marine Corps Manpower and Reserve Affairs (M&RA) office has the...2012 BAH Rates-with Dependents. Defense Travel Mangement Office. (2011, December). 2012 BAH Rates-without Dependents. M ileage C ost 1 Per D iem

77 FR 27788 - Notice of Issuance of Final Determination Concerning Special Ops Flashlights and Sportsman...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-11

... create a slight V shape; inserting the PCB into the battery tube; inserting the 3 V Lithium battery into... items are attached together. The power source used for the LED blank assemblies is a 3 volt lithium battery which is imported separately and sourced from China. The battery is attached to the LED blank in...

The MDT Innovation: Machine-Scoring of Fill-in-the-Blank Tests.

ERIC Educational Resources Information Center

Anderson, Paul S.

The Multi-Digit Technologies (MDT) testing technique is discussed as the first major advance in computer assisted testing in several decades. The MDT testing method uses fill-in-the-blank or completion-type questions, with an alphabetized long list of possible responses. An MDT answer sheet is used to record the code number of the answer. For…

New technology for low-grade hardwood utilization: System 6

Treesearch

Hugh W. Reynolds; Charles J. Gatchell

1982-01-01

System 6 is a technology for converting low-grade hardwood to high-valued end products such as furniture and kitchen cabinets. Among its concepts are: (1) a new, nonlumber product called standard-size blanks; (2) highly automated methods of converting the logs to blanks; (3) total processing of every board that contains a minimum-size cutting; and (4) minimized machine...

On the modeling of separation foils in thermoforming simulations

NASA Astrophysics Data System (ADS)

Margossian, Alexane; Bel, Sylvain; Hinterhölzl, Roland

2016-10-01

Composite forming simulations consist in modelling the forming process of composite components to anticipate the occurrence of potential flaws such as out-of-plane wrinkles and fibre re-orientation. Forming methods often consist of automated processes in which flat composite blanks are forced to comply with tool geometries. Although Finite Element forming simulations require the modelling of all stakeholders (blankholder, tooling and composite blank), consumables such as separation films are often not considered. Used in thermoforming processes, these films are placed between tooling and composite to ease part removal after forming. These films are also used to decrease tool/ply friction and thus, enhance forming quality. This work presents thermoforming simulations of pre-impregnated carbon fibre thermoplastic blanks in which separation films are modelled in the same manner as composite layers, i.e. by a layer of shell elements. The mechanical properties of such films are also characterised at the same temperature as forming occurs. The proposed approach is finally compared to the actual modelling method, in which separation films are not modelled as such but in which their influence is only considered within the friction coefficient between tooling and blank.

[Effect of Radix euphorbiae pekinensis extract on bioavailability of paclitaxel after their oral co-administration].

PubMed

Li, Minghua; Peng, Li; Yang, Fuheng; Liu, Sijia; Wang, Shengqi

2015-06-01

To evaluate the effect of Radix euphorbiae pekinensis extract on the permeability and bioavailability of paclitaxel co-administered orally. Based on Ussing Chamber and in vivo experiment, the permeability and bioavailability of paclitaxel were evaluated after oral co-administration with radix euphorbiae pekinensis in rats. The contents of paclitaxel in the permeates and the blood samples were determined using HPLC and LC-MS/MS method, respectively. In Radix euphorbiae pekinensis co-administration group, the Papp of the mucosal-to-serosal (M-S) transport or serosal-to-mucosal transport (S-M) of paclitaxel in the jejunum or ileum segment differed significantly from those in verapamil co-administration group and blank control group (P<0.05), but the Papp of S-M transport in the colon showed no significant difference from that in the blank control group. In the blank group, the average absolute bioavailability (AB%) of orally administered paclitaxel was only 2.81%, compared to that of 7.63% in radix euphorbiae pekinensis group. The average AB% in verapamil group was about 1.5 times that of the blank group. Co-administration of Radix euphorbiae pekinensis extract can increase the bioavailability of orally administered paclitaxel.

In vitro evaluation of antitumor activity of doxorubicin-loaded nanoemulsion in MCF-7 human breast cancer cells

NASA Astrophysics Data System (ADS)

Alkhatib, Mayson H.; AlBishi, Hayat M.

2013-03-01

Doxorubicin (DOX) is an anticancer drug used to treat several cancer diseases. However, it has several dose limitation aspects because of its poor bioavailability, hydrophobicity, and cytotoxicity. In this study, five nanoemulsion (NE) formulations, containing soya phosphatidylcholine/polyoxyethylenglycerol trihydroxy-stearate 40 (EU)/sodium oleate as surfactant, cholesterol (CHO) as oil phase, and Tris-HCl buffer (pH 7.22), were produced. The NE droplets morphologies of the entire blank and DOX-loaded formulations, revealed by the transmission electron microscope, were spherical. The droplet sizes of blank NEs, obtained between 2.9 and 6.4 nm, decreased significantly with the increase in the ratio of surfactant-to-oil, whereas the droplets sizes of DOX-loaded NE formulations were significantly higher and found in the range of 7.7-15.9 nm. The evaluation for both blank and DOX-loaded NE formulations proved that the NE carrier had improved the DOX efficacy and reduced its cytotoxicity. It showed that the cell growth inhibition of the breast cancer cells (MCF-7) have exceeded the commercial DOX by a factor of 1.7 with increased apoptosis activity and minimal cytotoxicity against the normal human foreskin cells (HFS). In contrast, commercial DOX was found to exhibit a significant non-selective toxicity against both MCF-7 and HFS cells. In conclusion, we have developed DOX-loaded NE formulations which selectively and significantly inhibited cell proliferation of MCF-7 cells and increased apoptosis.

Immunotherapy with dendritic cells and cytokine-induced killer cells for MDA-MB-231 breast cancer stem cells in nude mice

PubMed Central

Chen, Qiang; Cui, Xiao-Xu; Liang, Pei-Fen; Dou, Jin-Xia; Liu, Zi-Yan; Sun, Wen-Wen

2016-01-01

Objective: To compare the effects and safety of immunotherapy using different methods to load DC-CIK cells for MDA-MB-231 breast cancer stem cells. Methods: A breast cancer model was established in BALB/c nude mice using breast cancer stem cells. All mice were randomly divided into six groups, and each group had three nude mice: the blank control group, the DC-CIK group (group D), the MDA-MB-231 CSC whole-cell lysate DC-CIK group (group L-D), the MDA-MB-231 CSC RNA DC-CIK group (group R-D), the THP DC-CIK group (group T-D) and group THP. Nude mice in groups D, L-D, R-D and T-D were injected with CSCs; 4 days later, the mice were inoculated with 1 × 106 DC-CIK cells via the tail vein. This injection was repeated 2 times a week for three weeks. The mice in groups THP and T-D were injected with a 5 mg/Kg dose of THP chemotherapeutic agents via the tail vein the day before DC-CIK injection, which was repeated one time a week for three weeks. Nude mice in the blank control group were injected with normal saline. The weights and sizes of the tumors were measured after the mice were euthanized. The expression of c-Myc, a key proto-oncogene associated with the Akt signaling pathway, was detected with RT-PCR. Results: The tumor growth rates in each group were as follows: group L-D < group R-D < group D < group T-D < blank control group < group THP. The nude mice in groups L-D, R-D and D were normal, active and had a healthy appetite. The mice in groups T-D and THP were lethargic, less active and showed loss of appetite, and their caudal vein was easy to stimulate. The mice in the blank control group were sacrificed during the third week or when their tumors developed ulceration. Compared with the blank control group, c-Myc gene expression was reduced in the tumors of the five experimental groups. Conclusion: The results showed that DC-CIK cells stimulated by different methods were highly effect against MDA-MB-231 breast cancer stem cells in nude mice in all groups, especially in group L-D. DC-CIK immunotherapy may provide a new strategy for the clinical treatment of breast cancer. PMID:27508015

Immunotherapy with dendritic cells and cytokine-induced killer cells for MDA-MB-231 breast cancer stem cells in nude mice.

PubMed

Chen, Qiang; Cui, Xiao-Xu; Liang, Pei-Fen; Dou, Jin-Xia; Liu, Zi-Yan; Sun, Wen-Wen

2016-01-01

To compare the effects and safety of immunotherapy using different methods to load DC-CIK cells for MDA-MB-231 breast cancer stem cells. A breast cancer model was established in BALB/c nude mice using breast cancer stem cells. All mice were randomly divided into six groups, and each group had three nude mice: the blank control group, the DC-CIK group (group D), the MDA-MB-231 CSC whole-cell lysate DC-CIK group (group L-D), the MDA-MB-231 CSC RNA DC-CIK group (group R-D), the THP DC-CIK group (group T-D) and group THP. Nude mice in groups D, L-D, R-D and T-D were injected with CSCs; 4 days later, the mice were inoculated with 1 × 10(6) DC-CIK cells via the tail vein. This injection was repeated 2 times a week for three weeks. The mice in groups THP and T-D were injected with a 5 mg/Kg dose of THP chemotherapeutic agents via the tail vein the day before DC-CIK injection, which was repeated one time a week for three weeks. Nude mice in the blank control group were injected with normal saline. The weights and sizes of the tumors were measured after the mice were euthanized. The expression of c-Myc, a key proto-oncogene associated with the Akt signaling pathway, was detected with RT-PCR. The tumor growth rates in each group were as follows: group L-D < group R-D < group D < group T-D < blank control group < group THP. The nude mice in groups L-D, R-D and D were normal, active and had a healthy appetite. The mice in groups T-D and THP were lethargic, less active and showed loss of appetite, and their caudal vein was easy to stimulate. The mice in the blank control group were sacrificed during the third week or when their tumors developed ulceration. Compared with the blank control group, c-Myc gene expression was reduced in the tumors of the five experimental groups. The results showed that DC-CIK cells stimulated by different methods were highly effect against MDA-MB-231 breast cancer stem cells in nude mice in all groups, especially in group L-D. DC-CIK immunotherapy may provide a new strategy for the clinical treatment of breast cancer.

Availability of solar energy reports from the National Solar Data Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-07-01

This booklet discusses the various types of reports published by the National Solar Data Program, lists the reports issued prior to July 15, 1981, and provides order blanks for obtaining copies of reports. The reports identified in the following pages are segmented into nine types: monthly performance reports; solar energy performance evaluation reports; solar performance bulletins;environmental data reports;solar project description reports;solar project cost reports;program information reports;comparative reports; and reliability and material assessment reports. For convenience, available site-specific reports are listed alphabetically by site name, solar system type, and by state. These reports are disseminated through the US Department of Energy,more » Technical Information Center, P.O. Box 62, Oak Ridge, Tennessee 37830.« less

Psychological, behavioral and familial factors in obese Cuban children and adolescents.

PubMed

Pérez, Lourdes M; García, Keytel; Herrera, Raúl

2013-10-01

The global prevalence of obesity has reached alarming proportions. In Cuba, the rise in numbers of children who are overweight or obese, especially preschoolers and adolescents, is similar to that observed in developed countries. Beyond the physical risk factors, there is evidence that obesity has negative psychological, social, academic and economic effects. Describe the psychological, behavioral and familial factors present in a group of obese children and adolescents in Cuba. This is a qualitative cross-sectional study of 202 obese children and adolescents aged 3-18 years, with an average age of 9.9 years, seen at the Medical-Surgical Research Center (Havana) psychology service from January 2009 through December 2012. Techniques included interviews of patients and parents, projective drawings and the Rotter Incomplete Sentence Blank. Unhealthy eating habits were reported in 96% of obese children and adolescents, and sedentary lifestyles in 88.1%. Emotional state was affected in 80.2%, and in 72.3% there were family attitudes with potential to produce psychological disturbances in children. Psychological, behavioral, and familial factors known to foster development and perpetuation of obesity were observed in the majority of cases. This is a first diagnostic stage that will aid in design and implementation of a psychological intervention program for obese and overweight children and their families.

Surviving Sudden Cardiac Arrest: A Pilot Qualitative Survey Study of Survivors.

PubMed

Sawyer, Kelly N; Brown, Frances; Christensen, Roxanne; Damino, Colleen; Newman, Mary M; Kurz, Michael C

2016-06-01

Research describing survivors of sudden cardiac arrest (SCA) has centered on quantifying functional ability, perceived quality of life, and neurocognitive assessment. Many gaps remain, however, regarding survivors' psychosocial perceptions of life in the aftermath of cardiac arrest. An important influence upon those perceptions is the presence of support and its role in a survivor's life. An Internet-based pilot survey study was conducted to gather data from SCA survivors and friends and/or family members (FFMs) representing their support system. The survey was distributed to members of the Sudden Cardiac Arrest Foundation (SCAF) via the Internet by SCAF leadership. Questions included both discrete multiple-choice and open-ended formats. Inductive thematic analyses were completed by three independent researchers trained in qualitative research methodology to identify primary themes consistent among study participants until thematic saturation was achieved. No statistical inferences were made. A total of 205 surveys were returned over the 5-month study period (July to November 2013); nine were received blank, leaving 196 surveys available for review. Major themes identified for survivors (N = 157) include the significance of and desire to share experiences with others; subculture identification (unique experience from those suffering a heart attack); and the need to seek a new normal, both personally and inter-personally. Major themes identified for FFMs (N = 39) include recognition of loved one's memory loss; a lack of information at discharge, including expectations after discharge; and concern for the patient experiencing another cardiac arrest. This pilot, qualitative survey study suggests several common themes important to survivors, and FFMs, of cardiac arrest. These themes may serve as a basis for future patient-centered focus groups and the development of patient-centered guidelines for patients and support persons of those surviving cardiac arrest.

Microstructure-Texture-Mechanical Properties in Hot Rolling of a Centrifugal Casting Ring Blank

NASA Astrophysics Data System (ADS)

Qin, Fang-cheng; Li, Yong-tang; Qi, Hui-ping; Ju, Li

2016-03-01

Deformation characteristic of centrifugal casting 25Mn steel was investigated by compression tests, and then processing maps were established. According to the deformation parameters identified from the established processing maps and hot ring rolling (HRR) process, the industrial test for the 25Mn ring blank was performed. Optical microscope (OM) and electron backscatter diffraction (EBSD) techniques were used for detecting grain boundary features and textures of deformation structures. The morphologies and mechanisms of tensile and impact fracture were revealed. The results show that softening effect plays a dominant role in higher temperatures of 1050-1150 °C and strain rates lower than 0.1 s-1. The average grain size of the rolled 25Mn ring is about 28 μm, but the grains are more coarse and inhomogeneous on the middle layer than that on rest of the areas. The texture on the outer layer is characterized by strong {110} <112> and weak {112} <111>, followed by {001} <100> and {001} <110> on the inner layer and {110} <110> on the center layer, which is mainly associated with the shear deformation. The rolled ring with precise geometrical dimensions and sound mechanical properties is fabricated by HRR. Tensile fracture is composed of clear river-shaped pattern and a little dimple near the inner layer and outer layer, and the fracture mechanism is mainly quasi-cleavage fracture, accompanied by dimple fracture. The morphologies of impact fracture consist of tear ridge and cleavage platform.

Undersea Communications Between Submarines and Unmanned Undersea Vehicles in a Command and Control Denied Environment

DTIC Science & Technology

2015-03-01

public release; distribution is unlimited THIS PAGE INTENTIONALLY LEFT BLANK REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public ...AVAILABILITY STATEMENT 12b. DISTRIBUTION CODE Approved for public release; distribution is tmlimited 13. ABSTRACT (maximum 200 words) Nuclear powered...INTENTIONALLY LEFT BLANK Approved for public release; distribution is unlimited UNDERSEA COMMUNICATIONS BETWEEN SUBMARINES AND UNMANNED UNDERSEA VEHICLES IN A

Preventing Firefighter Exposure Hazards

DTIC Science & Technology

2017-09-01

INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No.0704-0188 Public reporting burden for this collection of information is... Form 298 (Rev.2-89) Prescribed by ANSI Std.239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release. Distribution is...have been proven harmful to humans when they are in chemical form , it is difficult to measure their harmfulness when the chemicals are transformed

STARE CubeSat Communications Testing, Simulation and Analysis

DTIC Science & Technology

2012-09-01

26  Figure 24.  STK MC3 Ground Station Locations ................................................... 31  x THIS PAGE INTENTIONALLY LEFT BLANK xi...Refinement of Ephemeris STK Satellite Tool Kit VPN Virtual Private Network xiv THIS PAGE INTENTIONALLY LEFT BLANK xv ACKNOWLEDGMENTS This...the radio itself. Using a signal attenuator to decrease signal strength by 10 dB increments, and a spectrum analyzer to see a visual representation

Conventional Processing of Standard-Size Edge-Glued Blanks for Furniture and Cabinet Parts: a Feasibility Study

Treesearch

Philip A. Araman; Bruce G. Hansen

1983-01-01

Manufacturers of furniture and cabinets use more than 2 billion board feet of hardwood lumber annually. As demand intensifies, we will need to utilize more of the abundant lower grade hardwood resource to assure future supplies at reasonable prices. Conventional processing of standard-size hardwood blanks manufactured from log-run red oak lumber, a resource containing...

A Seakeeping Study on the Autonomous Sustainment Cargo Container Delivery System

DTIC Science & Technology

2008-03-01

reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instruction, searching...Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2. REPORT DATE March...THIS PAGE INTENTIONALLY LEFT BLANK vii TABLE OF CONTENTS I. THE AUTONOMOUS SUSTAINMENT CONTAINER CONCEPT .................... 1 A. BACKGROUND

Exploratory Study of the Potential Effects of Exposure to Sonic Boom on Human Health. Volume 2. Epidemiological Study.

DTIC Science & Technology

1986-06-01

were retained from the original source. The undesired data lines in both shortened population files were then manually deleted through full-screen...Prenatal Visits 00-99 00-blank 88-not on certificate 99-unknown Apgar Score: 161-162 1 min. 00-10, 88, 99 99-entry >10 88-not on record 00=blank 163

Government Venture Capital: Centralized or Decentralized Execution

DTIC Science & Technology

2007-12-01

Approved for public release; distribution is unlimited. THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704...LIMITATION OF ABSTRACT UU NSN 7540-01-280-5500 Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT...and Public Policy iv THIS PAGE INTENTIONALLY LEFT BLANK v GOVERNMENT VENTURE CAPITAL: CENTRALIZED OR DECENTRALIZED EXECUTION? ABSTRACT

Distribution of HLA class I alleles and haplotypes in Korean.

PubMed Central

Kim, T. G.; Han, H.; Lim, B. U.; Kim, W.; Kim, S. M.

1993-01-01

The antigen (phenotype), gene (allele) and haplotype frequencies of HLA class I were analysed in 4,622 Koreans. With allele frequencies of over 0.05, the most frequent HLA-A,-B and -C antigens were A2, A24, A33, A11, A26, A31; B62, B51, B44, B54, B61, B35, B58, B60; Cw3, Cw1, Cw4, Cw7. Of these A2, A24, Cw1 and Cw3 were present in very high frequencies, respectively (0.3211, 0.2200, 0.2204, and 0.3737). The most common haplotypes with frequencies larger than 0.02 were A2-Blank, A33-B44, A33-B58, A11-B62, A24-B51, A24-B54, A2-B27, B54-Cw1, B58-Cw3, B51-Blank, B61-Cw3, B62-Cw4, B35-Cw3, B44-Blank, B60-Cw3, B27-Cw1, A2-Cw3, A2-Cw1, A24-Cw1, A33-Cw3, A26-Cw3, and A11-Cw4. A significant negative linkage disequilibrium was found for the haplotypes of A2-B7, A2-B44, A2-B58, A24-B13, A24-B27, A33-B54 and A33-B62, of which frequencies were larger than 0.003. The B-C and A-C haplotypes which showed the significant negative linkage disequilibrium were B44-Cw1, B51-Cw1, B44-Cw3,B62-Blank, A2-Cw4, A2-Blank, A11-Cw3, A11-Blank and A33-Cw1 and had frequencies higher than 0.01. The findings presented here could be used per se to estimate the populational relationships or as the control data for HLA-disease investigation. Furthermore they could provide the scope for the definition of new antigens. PMID:8240747

Navigational Heads-Up Display: Will a Shipboard Augmented Electronic Navigation System Sink or Swim?

DTIC Science & Technology

2015-03-01

of Management and Budget, Paperwork Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) I 2. REPORT DATE I 3. REPORT...empirical results demonstrate the viability of using such a system in an operation environment and support a need for further research and development...empirical results demonstrate the viability of using such a system in an operation environment and support a need for further research and development

Determination of small amounts of molybdenum in tungsten and molybdenum ores

USGS Publications Warehouse

Grimaldi, F.S.; Wells, R.C.

1943-01-01

A rapid method has been developed for the determination of small amounts of molybdenum in tungsten and molybdenum ores. After removing iron and other major constituents the molybdenum thiocyanate color is developed in water-acetone solutions, using ammonium citrate to eliminate the interference of tungsten. Comparison is made by titrating a blank with a standard molybdenum solution. Aliquots are adjusted to deal with amounts of molybdenum ranging from 0.01 to 1.30 mg.

Developing Novel Conjugate HIV-1 Subunit Therapeutic Vaccines.

DTIC Science & Technology

1996-06-01

significant CD4-binding was observed for gpl20-KLH conjugates prepared using 1 -ethyl- 3 -( 3 - dimethylaminopropyl )carbodiimide hydrochloride (EDC). EDC...Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2. REPORT DATE 3 . REPORT TYPE AND...FOREWORD 3 TABLE OF CONTENTS 4 INTRODUCTION 5 RESULTS 6 Specific Aim # 1 : Production and characterization of HIV-JlV and HIV-1jR_ gp120 6 Development and

Hand-Held Calculator Algorithms for Coastal Engineering.

DTIC Science & Technology

1982-01-01

and water depth at the structure toe, ds. The development of the equation is derived on the solution sheet included with program 104R. Algorithm uses...Limited Design Breaking Wave Height at Structure (AOS logic)... .... ....... ......... .54 6. 105R Wave Transmission - Fuchs’ Equation (RPN logic...58 105A Wave Transmission - Fuchs’ Equation (AOS logic). . . . 61 APPENDIX BLANK PROGRAM FORMS ........ ....................... ... 67 4

Test Plan Framework for Cross Domain Solution (CDS) Devices

DTIC Science & Technology

2010-06-01

modification to the CASTER software to reflect the latest changes to RDAC is being discussed by the developers with input by the independent labs and NSA...7 xii THIS PAGE INTENTIONALLY LEFT BLANK xiii LIST OF ABBREVIATIONS AND ACRONYMS CASTER Certification...protecting information and information systems from unauthorized access, use, disclosure, disruption, modification , or destruction. While this is a

Degraded Imagery/Art Technique for the Handicapped.

ERIC Educational Resources Information Center

Agard, Richard

Developed for handicapped artists, Degraded Imagery is a technique whereby images can be extracted and refined from a photograph or a collage of photographs. The advantage of this process is that it requires a lower degree of fine motor skills to produce a quality image from a photograph than it does to create a quality image on a blank piece of…

A Peroxidase-linked Spectrophotometric Assay for the Detection of Monoamine Oxidase Inhibitors

PubMed Central

Zhi, Kangkang; Yang, Zhongduo; Sheng, Jie; Shu, Zongmei; Shi, Yin

2016-01-01

To develop a new more accurate spectrophotometric method for detecting monoamine oxidase inhibitors from plant extracts, a series of amine substrates were selected and their ability to be oxidized by monoamine oxidase was evaluated by the HPLC method and a new substrate was used to develop a peroxidase-linked spectrophotometric assay. 4-(Trifluoromethyl) benzylamine (11) was proved to be an excellent substrate for peroxidase-linked spectrophotometric assay. Therefore, a new peroxidase-linked spectrophotometric assay was set up. The principle of the method is that the MAO converts 11 into aldehyde, ammonia and hydrogen peroxide. In the presence of peroxidase, the hydrogen peroxide will oxidize 4-aminoantipyrine into oxidised 4-aminoantipyrine which can condense with vanillic acid to give a red quinoneimine dye. The production of the quinoneimine dye was detected at 490 nm by a microplate reader. The ⊿OD value between the blank group and blank negative control group in this new method is twice as much as that in Holt’s method, which enables the procedure to be more accurate and avoids the produce of false positive results. The new method will be helpful for researchers to screening monoamine oxidase inhibitors from deep-color plant extracts. PMID:27610153

A Peroxidase-linked Spectrophotometric Assay for the Detection of Monoamine Oxidase Inhibitors.

PubMed

Zhi, Kangkang; Yang, Zhongduo; Sheng, Jie; Shu, Zongmei; Shi, Yin

2016-01-01

To develop a new more accurate spectrophotometric method for detecting monoamine oxidase inhibitors from plant extracts, a series of amine substrates were selected and their ability to be oxidized by monoamine oxidase was evaluated by the HPLC method and a new substrate was used to develop a peroxidase-linked spectrophotometric assay. 4-(Trifluoromethyl) benzylamine (11) was proved to be an excellent substrate for peroxidase-linked spectrophotometric assay. Therefore, a new peroxidase-linked spectrophotometric assay was set up. The principle of the method is that the MAO converts 11 into aldehyde, ammonia and hydrogen peroxide. In the presence of peroxidase, the hydrogen peroxide will oxidize 4-aminoantipyrine into oxidised 4-aminoantipyrine which can condense with vanillic acid to give a red quinoneimine dye. The production of the quinoneimine dye was detected at 490 nm by a microplate reader. The ⊿OD value between the blank group and blank negative control group in this new method is twice as much as that in Holt's method, which enables the procedure to be more accurate and avoids the produce of false positive results. The new method will be helpful for researchers to screening monoamine oxidase inhibitors from deep-color plant extracts.

An Artificial Turf-Based Surrogate Surface Collector for the Direct Measurement of Atmospheric Mercury Dry Deposition

PubMed Central

Hall, Naima L.; Dvonch, Joseph Timothy; Marsik, Frank J.; Barres, James A.; Landis, Matthew S.

2017-01-01

This paper describes the development of a new artificial turf surrogate surface (ATSS) sampler for use in the measurement of mercury (Hg) dry deposition. In contrast to many existing surrogate surface designs, the ATSS utilizes a three-dimensional deposition surface that may more closely mimic the physical structure of many natural surfaces than traditional flat surrogate surface designs (water, filter, greased Mylar film). The ATSS has been designed to overcome several complicating factors that can impact the integrity of samples with other direct measurement approaches by providing a passive system which can be deployed for both short and extended periods of time (days to weeks), and is not contaminated by precipitation and/or invalidated by strong winds. Performance characteristics including collocated precision, in-field procedural and laboratory blanks were evaluated. The results of these performance evaluations included a mean collocated precision of 9%, low blanks (0.8 ng), high extraction efficiency (97%–103%), and a quantitative matrix spike recovery (100%). PMID:28208603

Antiprogestin-releasing intrauterine devices

PubMed Central

Nayak, NR; Slayden, OD; Mah, K; Chwalisz, K; Brenner, Robert M

2007-01-01

Intrauterine devices (IUDs) that release progestins are highly effective contraceptives, but they induce breakthrough bleeding that some women find unacceptable. Because progesterone (P) antagonists (AP) are known to suppress the endometrium, induce amenorrhea, and inhibit fertility, AP IUDs may provide an effective contraceptive that also controls endometrial bleeding. Here we assessed the effects of empty (blank) vs AP-releasing (ZK 230 211) IUDs on bleeding patterns and endometrial growth in ovariectomized, artificially cycled macaques. The AP IUDs (but not the blank controls) induced extended, frank menstruation when inserted during the late luteal phase, an indication of local AP action. Over time, endometrial glandular and arterial proliferation were inhibited, steroid receptors were elevated, spiral arteries showed degenerative changes, progesterone withdrawal bleeding was prevented and estradiol-dependent proliferation was suppressed by the AP IUDs. In sum, AP IUDs suppressed the effects of P on endometrial progestational development and blocked the effects of estradiol on endometrial proliferation as previously shown for systemic treatment with APs. Therefore, AP IUDs may provide novel contraceptive devices with minimal breakthrough bleeding. PMID:17531599

Stamp forming optimization for formability and crystallinity

NASA Astrophysics Data System (ADS)

Donderwinkel, T. G.; Rietman, B.; Haanappel, S. P.; Akkerman, R.

2016-10-01

The stamp forming process is well suited for high volume production of thermoplastic composite parts. The process can be characterized as highly non-isothermal as it involves local quench-cooling of a molten thermoplastic composite blank where it makes contact with colder tooling. The formability of the thermoplastic composite depends on the viscoelastic material behavior of the matrix material, which is sensitive to temperature and degree of crystallinity. An experimental study was performed to determine the effect of temperature and crystallinity on the storage modulus during cooling for a woven glass fiber polyamide-6 composite material. An increase of two decades in modulus was observed during crystallization. As this will significantly impede the blank formability, the onset of crystallization effectively governs the time available for forming. Besides the experimental work, a numerical model is developed to study the temperature and crystallinity throughout the stamp forming process. A process window can be determined by feeding the model with the experimentally obtained data on crystallization.

Gemini 8.2-m primary mirror no. 1 polishing

NASA Astrophysics Data System (ADS)

Cayrel, Marc; Beraud, P.; Paseri, Jacques; Dromas, E.

1998-08-01

The 8-m class primary mirrors of the GEMINI Telescopes are thin ULE menisci actively supported. The two mirror blanks are produced by CORNING, the optical figuring, manufacturing and assembling of interfaces are done by REOSC. REOSC is as well in charge of the transportation of the mirror blanks from CORNING to REOSC, and of the shipment of the finished optics to Hawaii and to Chile. The mirror assembly requirements are summarized, the manufacturing and testing methods are addressed. REOSC had to design and manufacture a dedicated active supporting system, representative of the one used at the telescope level. Its design and performance are presented. The manufacturing steps undertaken at REOSC and the results achieved are then detailed: mirror blank surface generating and grinding, polishing, testing. The current status of the mirrors is finally presented.

Aqueous geochemical data from the analysis of stream water samples collected in August 2004--Taylor Mountains 1:250,000 scale Quadrangle, Alaska

USGS Publications Warehouse

Wang, Bronwen; Mueller, Seth; Bailey, Elizabeth; Lee, Greg

2006-01-01

We report on the chemical analysis of water samples collected from the Taylor Mountains 1:250,000 quadrangle. Samples were collected as part of the multi-year U.S. Geological Survey's project -- Geologic and Mineral Deposit Data for Alaskan Economic Development. Data presented here are from water samples collected primarily in the northeastern part of the Taylor Mountains quadrangle. The data include samples taken from the Taylor Mountains C1, C2, D1, D2, and D4 1:63,360 scale quadrangles. The data are being released at this time with minimal interpretation. Site selection was based on a regional sampling strategy that focused on first and second order drainages. Water sampling site selection was based on landscape parameters that included physiography, wetland extent, lithological changes, and the cursory field review of the mineralogy from the pan concentrates. Stream water in the Taylor Mountians quadrangle is dominated by bicarbonate (HCO3-), though in a few samples more than 50% of the anionic charge can be attibuted to sulfate ( SO42-). The major-cation chemistry range from Ca/Mg dominated to a mix of Ca/Mg/Na+K. Good agreement was found between the major cation and anions in the duplicate samples. Many trace elements were at or near the method detection limit in these samples but good agreement was found between duplicate samples for elements with detectable concentrations. Major ion concentrations were below detection in all field blanks and the trace elements concentrations generally were below detection. However, Ta (range 0.9 -.1 ug/L) and Zn (1 to 3.5 ug/L) were detected in all blanks and Ba ( 0.24 ug/L) and Th (0.2 ug/L) were detected in one blank. There was good agreement between dupilicate total- and methyl- mercury and DOC samples; however, total mercury, methyl-mercury and dissolve organic carbon (DOC) were detected in the blank at 2.35 ng/L, 0.07 ng/L and 0.57 mg/L, respectively.

49 CFR 40.253 - What are the procedures for conducting an alcohol confirmation test?

Code of Federal Regulations, 2010 CFR

2010-10-01

... confirmation test and show the reading to the employee. (1) If the reading is 0.00, the test may proceed. If the reading is greater than 0.00, you must conduct another air blank. (2) If the reading on the second air blank is 0.00, the test may proceed. If the reading is greater than 0.00, you must take the EBT...

49 CFR 40.253 - What are the procedures for conducting an alcohol confirmation test?

Code of Federal Regulations, 2011 CFR

2011-10-01

... confirmation test and show the reading to the employee. (1) If the reading is 0.00, the test may proceed. If the reading is greater than 0.00, you must conduct another air blank. (2) If the reading on the second air blank is 0.00, the test may proceed. If the reading is greater than 0.00, you must take the EBT...

Motivating Employees in Times of Recession: Recommendations for the Hellenic Navy

DTIC Science & Technology

2013-03-01

Management and Budget, Paperwork Reduction Project (0704–0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE March 2013...and my children, Christina and Thomas, who supported me during my studies at NPS. xviii THIS PAGE INTENTIONALLY LEFT BLANK 1 I...performance excellence. Yet, how can one motivate employees who work more for lower earnings and reduced benefits? This project intends to explore this

Glycopeptides as Analgesics: Non-Toxic Alternatives to Morphine for Combat Casualty Care

DTIC Science & Technology

2013-12-05

Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503 1. Agency Use Only (Leave blank) 2. Report Date 5 December 2013...Performing Organization Name (Include Name, City, State, Zip Code and Email for Principal Investigator) The University of Arizona Tucson, Arizona...85722-3308 E-Mail: poltSu. arizona . edu 8. Performing Organization Report Number (Leave Blank) 9. Sponsoring/Monitoring Agency Name and Address

Modeling of the Electric Ship

DTIC Science & Technology

2010-06-01

2009, Northrop Grumman and American Superconductor, under an Office of Naval Research contract, successfully tested a HTS AC synchronous motor (HTS ACSM...BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting burden for this collection of information is estimated to average 1 ...Washington DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2. REPORT DATE June 2010 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND

THE PHYSIOLOGICAL SIGNIFICANCE OF THE CORTIOOSTEROIDS IN PAROTID FLUID.

DTIC Science & Technology

A highly sensitive and highly specific technique was devised, utilizing four chromatographic procedures, for the measurement of parotid fluid...cortisol and cortisone on 5 ml of parotid fluid, and plasma cortisol on 1 ml of plasma. In addition techniques are described for measuring plasma...derivative technique is high purified immediately before its use, blank values are too high for the low values found in parotid saliva. Blank values

Has the Department of Homeland Security (DHS) Outlived Its Usefulness?

DTIC Science & Technology

2012-12-01

Carolyn Halladay THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting burden for this...LIMITATION OF ABSTRACT UU NSN 7540-01-280-5500 Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT...Trinkunas Chair, Department of National Security Affairs iv THIS PAGE INTENTIONALLY LEFT BLANK v ABSTRACT The Department of Homeland Security

System 6: making frame-quality blanks from white oak thinnings

Treesearch

Hugh W. Reynolds; Philip A. Araman

1983-01-01

Low-grade white oak timber removed during a timber stand improvement cut on the Jefferson National Forest in Virginia was made into sawlogs, poles, 6-foot bolts, 4-foot bolts, pulpwood, and firewood. The 6-foot bolts were sawed to two cants per bolt; cants were resawed to 4/4 System 6 boards; boards were dried to 6 percent moisture content and made into frame blanks...

Toward Finding Driving Communications Factors in the System of Systems Survivability Simulation Model

DTIC Science & Technology

2014-03-01

BLANK 53 LIST OF REFERENCES Bernstein Jr ., R., Flores , R., & Starks, M. (2006). Objectives and capabilities of the system of...Reader Robert Dell Chair, Department of Operations Research iv THIS PAGE INTENTIONALLY LEFT BLANK v ABSTRACT The System of Systems...larger system (Starks & Flores , 2004). One of the primary concerns for a new platform is its survivability, lethality, and vulnerability (SLV) as part

Effect of Test-Expectancy and Word Bank Availability on Test Performance

ERIC Educational Resources Information Center

Glass, Laura A.; Clause, Christopher B.; Kreiner, David S.

2007-01-01

We examined test-expectancy as it applies to fill-in-the-blank tests. We randomly assigned 60 college students to take a fill-in-the-blank vocabulary test in one of three conditions. Two groups took the test with a word bank available; we told one group but not the other that they would have a word bank. The third group took the test with no word…

Comparison of Select Analytes in Exhaled Aerosol from E-Cigarettes with Exhaled Smoke from a Conventional Cigarette and Exhaled Breaths

PubMed Central

Long, Gerald A.

2014-01-01

Exhaled aerosols were collected following the use of two leading U.S. commercial electronic cigarettes (e-cigarettes) and a conventional cigarette by human subjects and analyzed for phenolics, carbonyls, water, glycerin and nicotine using a vacuum-assisted filter pad capture system. Exhaled breath blanks were determined for each subject prior to each product use and aerosol collection session. Distribution and mass balance of exhaled e-cigarette aerosol composition was greater than 99.9% water and glycerin, and a small amount (<0.06%) of nicotine. Total phenolic content in exhaled e-cigarette aerosol was not distinguishable from exhaled breath blanks, while total phenolics in exhaled cigarette smoke were significantly greater than in exhaled e-cigarette aerosol and exhaled breaths, averaging 66 µg/session (range 36 to 117 µg/session). The total carbonyls in exhaled e-cigarette aerosols were also not distinguishable from exhaled breaths or room air blanks. Total carbonyls in exhaled cigarette smoke was significantly greater than in exhaled e-cigarette aerosols, exhaled breath and room air blanks, averaging 242 µg/session (range 136 to 352 µg/session). These results indicate that exhaled e-cigarette aerosol does not increase bystander exposure for phenolics and carbonyls above the levels observed in exhaled breaths of air. PMID:25350011

Comparison of select analytes in exhaled aerosol from e-cigarettes with exhaled smoke from a conventional cigarette and exhaled breaths.

PubMed

Long, Gerald A

2014-10-27

Exhaled aerosols were collected following the use of two leading U.S. commercial electronic cigarettes (e-cigarettes) and a conventional cigarette by human subjects and analyzed for phenolics, carbonyls, water, glycerin and nicotine using a vacuum-assisted filter pad capture system. Exhaled breath blanks were determined for each subject prior to each product use and aerosol collection session. Distribution and mass balance of exhaled e-cigarette aerosol composition was greater than 99.9% water and glycerin, and a small amount (<0.06%) of nicotine. Total phenolic content in exhaled e-cigarette aerosol was not distinguishable from exhaled breath blanks, while total phenolics in exhaled cigarette smoke were significantly greater than in exhaled e-cigarette aerosol and exhaled breaths, averaging 66 µg/session (range 36 to 117 µg/session). The total carbonyls in exhaled e-cigarette aerosols were also not distinguishable from exhaled breaths or room air blanks. Total carbonyls in exhaled cigarette smoke was significantly greater than in exhaled e-cigarette aerosols, exhaled breath and room air blanks, averaging 242 µg/session (range 136 to 352 µg/session). These results indicate that exhaled e-cigarette aerosol does not increase bystander exposure for phenolics and carbonyls above the levels observed in exhaled breaths of air.

Developments in ICP-MS: electrochemically modulated liquid chromatography for the clean-up of ICP-MS blanks and reduction of matrix effects by flow injection ICP-MS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gross, Cory Thomas

2008-01-01

The focus of this dissertation is the development of techniques with which to enhance the existing abilities of inductively coupled plasma mass spectrometry (ICP-MS). ICP-MS is a powerful technique for trace metal analysis in samples of many types, but like any technique it has certain strengths and weaknesses. Attempts are made to improve upon those strengths and to overcome certain weaknesses.

Development of Methodology and Technology for Identifying and Quantifying Emission Products from Open Burning and Open Detonation Thermal Treatment Methods. Bangbox Test Series. Volume 2. Test Development

DTIC Science & Technology

1992-01-01

Calculated by the Carbon Balance and by the C -V M ethod . ...................................... ... ... ... ... ... 6-8 x I I Table 6.3 EF for the...A-i APPENDIX B. SAMPLING AND DETERMINATION OF POLYCHLORINATED DIBENZODIOXINS AND DIBENZOFURANS ................. B-13 APPENDIX C . DISTRIBUTION... C -I I I I I I I I I I I I I I xiii I INTENTIONALLY BLANK xiv --I IACKNOWLEDGEMENTS I The following

Expendable Air Vehicles/High Altitude Balloon Technology. Phase 1.

DTIC Science & Technology

1991-08-02

CHR/91 -2750 I I I I I THIS PAGE INTENTIONALLY LEFT BLANK 3 I I U I I I I I I I I I CHR/91 -2750 PREFACE The work described in this Phase II SBIR...Final Technical Report is the implementation of a capability which Coleman Research Corporation demon- strated during a Phase I SBIR (contract number...CRC) has developed a Balloon Drift Pattern Simulation 1BDPS). CRC developed this simulation software for digital computers as a product of a Phase II

Springback optimization in automotive Shock Absorber Cup with Genetic Algorithm

NASA Astrophysics Data System (ADS)

Kakandikar, Ganesh; Nandedkar, Vilas

2018-02-01

Drawing or forming is a process normally used to achieve a required component form from a metal blank by applying a punch which radially draws the blank into the die by a mechanical or hydraulic action or combining both. When the component is drawn for more depth than the diameter, it is usually seen as deep drawing, which involves complicated states of material deformation. Due to the radial drawing of the material as it enters the die, radial drawing stress occurs in the flange with existence of the tangential compressive stress. This compression generates wrinkles in the flange. Wrinkling is unwanted phenomenon and can be controlled by application of a blank-holding force. Tensile stresses cause thinning in the wall region of the cup. Three main types of the errors occur in such a process are wrinkling, fracturing and springback. This paper reports a work focused on the springback and control. Due to complexity of the process, tool try-outs and experimentation may be costly, bulky and time consuming. Numerical simulation proves to be a good option for studying the process and developing a control strategy for reducing the springback. Finite-element based simulations have been used popularly for such purposes. In this study, the springback in deep drawing of an automotive Shock Absorber Cup is simulated with finite element method. Taguchi design of experiments and analysis of variance are used to analyze the influencing process parameters on the springback. Mathematical relations are developed to relate the process parameters and the resulting springback. The optimization problem is formulated for the springback, referring to the displacement magnitude in the selected sections. Genetic Algorithm is then applied for process optimization with an objective to minimize the springback. The results indicate that a better prediction of the springback and process optimization could be achieved with a combined use of these methods and tools.

High Precision Low-blank Lithium Isotope Ratios in Forams.

NASA Astrophysics Data System (ADS)

Misra, S.; Froelich, P. N.

2007-12-01

We present a high precision (±1‰, 2σ) low blank (<500 fg/ml) method for Li isotope measurements of forams using <2 ng of Li by single collector Quad ICP-MS (Agilent 7500cs). The Li isotope ratio of seawater (δ7Li) recorded in planktonic forams has the potential to constrain the evolution of seawater chemistry and elucidate the factors driving variations of oceanic mass balances linked to the continental and sea floor/hydrothermal silica cycles. In addition a δ7Li record of seawater will complement other long-term recorders of seawater chemistry such as Sr, Os and S isotopes. Li isotope measurements of forams are limited by several factors: low Li concentrations in forams (1-2 ppm), instrument-induced fractionation and mass bias effects, matrix effects, high Li blanks and incomplete recovery of Li during column separation. Modest concentrations of alkali and alkaline earth elements in the matrix result in variable mass bias in measured Li isotope ratios. Even worse, Li strongly fractionates during chromatographic clean-up to remove Na+, Ca2+ and Mg2+, from +100‰ in the leading edge to - 100‰ in the trailing edge of elution peaks (Urey 1938). Consequently, miniscule incomplete recoveries of Li during chromatographic separations can result in large unrecognized isotope fractionation of eluents. Large mass-dependent fractionation caused by a difference of 17% in mass between 6Li and 7Li, makes Li a powerful tracer of geochemical processes, but also promotes large and difficult-to-fix isotope fractionations during laboratory chemical processing. Matrix effects of Na & Ca and of column chromatography on Li isotope ratios were investigated using artificial Li solutions representative of foram compositions (matrix matching). Li/Ca and Li/Na ratios in cleaned forams are 10 μmol/mol and 3 mmol/mol respectively. An ICP-MS tolerance limit of 20 ppb for Na and 20 μM for Ca was established, much higher tolerances than by TIMS. A single step chromatographic method to quantitatively separate Li from matrix elements using both small volume resin (3.4 meq/2ml AG50W-X8) and acid (6 ml of 0.5N HCl) was developed. Our low blank (<0.5 pg/ml) and high yield (>99.99%) column method minimizes errors in measured Li isotope ratios associated with incomplete column recovery and presence of matrix elements. High sensitivity and precision achieved with a 7500cs using cold plasma (600W), soft extraction and peak jumping coupled with very low sample to blank ratios enables high precision (±1‰, 2σ) statistically significant Li isotope measurements using very small mass of Li (0.8 ng). The development of this technique makes possible good quality Li isotope measurements from samples that are mass limited for Li, i.e., reasonable number of picked forams. This will enable us to test interferences regarding chemical cleaning and species effects in planktonic forams along the road toward creating a δ7Li record of seawater for the Cenozoic.

Radon Assessment of Occupational Facilities, Homestead ARB, FL

DTIC Science & Technology

2013-11-21

electrets is directly measured and used to calculate radon levels. The radon detectors were placed in the test locations for greater than 90 days in...of USAFSAM’s radon analysis. A proficiency test was last performed and passed on 18 July 2012. (2) Blanks: Six field blanks were used during the...voltage. 5. CONCLUSIONS AND RECOMMENDATIONS: a. All 46 facilities tested had radon concentrations below the action limit of 4 pCi/L; no radon

Evaluation of safety of lipomer doxycycline hydrochloride (lipomer DH).

PubMed

Dhumal, Rohit; Soni, Mahesh; Devarajan, Padma; Samad, Abdul; Gaikwad, Rajiv; Vanage, Geeta

2011-02-01

The nanoparticulate formulation of lipomer doxycycline hydrochloride (lipomer DH) has been synthesized for the treatment of Brucellosis to increase efficacy of the drug. The present study was undertaken to determine the intravenous safety of blank lipomer and Lipomer DH in terms of maximum tolerated dose in rats. It was observed that blank lipomer and lipomer DH were safe when administered intravenously at doses 2000 mg/kg Bw and 18 mg/kg bw respectively.

Evaluation of a Ferroelectric Liquid Crystal Spatial Light Modulator

DTIC Science & Technology

1991-01-09

MAR 83 APR edition may be used until exhausted SECURITY CLASSIFICATION OF THIS PAGE All other edition% are obsolete UbIu.LAb F L l.D i/(ii Blank...7 VII. CONCLUSIONS.................................................. 8 Accesion For- NTIS CRA&I ~ 4Ii U, ai-;-oui iced L DiA: ibutiko: i...thin phase grating. The authors are also thankful for the assistance of Ms. Cindy Gabardi in preparing this manuscript. v/(vi Blank) 1. INTRODUCTION A

PSYOP Needs More Science: The Root Cause of the Branch’s Difficulties with Assessment

DTIC Science & Technology

2013-12-01

Office of Management and Budget, Paperwork Reduction Project (0704–0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE...our wives who encouraged and supported us throughout this educational process. xviii THIS PAGE INTENTIONALLY LEFT BLANK 1 I. INTRODUCTION A...manual. In Figure 1, the doubled line ending in a circle indicates a doctrinal item that has been specifically superseded. The dashed line ending

German Energy Security and Its Implications on Regional Security

DTIC Science & Technology

2016-12-01

Daniel Moran THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this...280-5500 Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public...independence.17 In the 1980s and 1990s, Esakova points out that energy security took a more economic form , with countries focusing on protecting their

Analysis of return on investment for Naval air station fallon energy project Alternatives

DTIC Science & Technology

2017-06-01

Second Reader: Daniel Nussbaum THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting...Standard Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release...be awarded in its current form as an Energy Savings Performance Contract (ESPC). This analysis can support the decision- making process for similar

LDDX: A High Efficiency Air Conditioner for DOD Buildings

DTIC Science & Technology

2017-02-01

or favoring by the Department of Defense. Page Intentionally Left Blank i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188...failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO... Form 298 (Rev. 8-98) Prescribed by ANSI Std. Z39.18 Page Intentionally Left Blank i COST & PERFORMANCE REPORT Project: EW-201137 TABLE OF

In-Service Inspection Approaches for Lead-Cooled Nuclear Reactors

DTIC Science & Technology

2017-06-01

Luscombe THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this...5500 Standard Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release...INTRODUCTION A. MOTIVATION Despite growing demand and increasing restrictions on fossil fuels, there is a technology gap for reliable, safe and non-carbon

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2012 CFR

2012-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2010 CFR

2010-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2013 CFR

2013-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2014 CFR

2014-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2011 CFR

2011-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

24 CFR Appendix A to Part 3500 - Instructions for Completing HUD-1 and HUD-1a Settlement Statements; Sample HUD-1 and HUD-1a...

Code of Federal Regulations, 2012 CFR

2012-04-01

... 803 and recorded in the columns. Blank lines are provided in section L for any additional settlement... recipients of the settlement charges in section L and the names of the recipients of adjustments described in... Borrower's transaction may be left blank on the copy of the HUD-1 which will be furnished to the Seller...

System 6 used to make kitchen cabinet C2F blanks from small-diameter, low-grade red oak

Treesearch

Hugh W. Reynolds; Philip A. Araman; Charles J. Gatchell; Bruce G. Hansen

1983-01-01

Hardwood dimension manufacturers can make profitable use of plentiful small-diameter, low-grade timber when System 6 technology is used. We describe a System 6 plant designed to make clear-two-face (C2F) blanks for the kitchen cabinet industry. Data for plant operation are taken from a study in which red oak bolts (from a reforestation clearcut) were used to make 33-,...

Investigation of pitch and angle in the gradual-triangle lenticular lens for point-blank LED fog lamp.

PubMed

Chen, Hsi-Chao; Yang, Chi-Hao

2014-05-10

The effects of different pitch and angle of gradual-triangle lenticular lens for the point-blank LED fog lamp were investigated under the standard of ECE R19. The novel LED fog lamp was assembled from a point-blank LED light source, a parabolic reflector, and a gradual-triangle lenticular lens. Light tracing analysis was used for the design of the gradual-triangle lenticular lens. The pitch, which varied from 1 to 6 mm, and the apex angle, which changed from 5 to 32 deg, were both investigated in regard to the gradual-triangle lenticular lens. The optimum pitch was 5 mm, and the efficiency of the lamp system and lenticular lens could reach 93% and 98.1% by simulation, respectively. The results of experiment had over 94%, which is similar to that of simulation by normalized cross correlation (NCC) for the light intensity.

Method for fabricating an ultra-low expansion mask blank having a crystalline silicon layer

DOEpatents

Cardinale, Gregory F.

2002-01-01

A method for fabricating masks for extreme ultraviolet lithography (EUVL) using Ultra-Low Expansion (ULE) substrates and crystalline silicon. ULE substrates are required for the necessary thermal management in EUVL mask blanks, and defect detection and classification have been obtained using crystalline silicon substrate materials. Thus, this method provides the advantages for both the ULE substrate and the crystalline silicon in an Extreme Ultra-Violet (EUV) mask blank. The method is carried out by bonding a crystalline silicon wafer or member to a ULE wafer or substrate and thinning the silicon to produce a 5-10 .mu.m thick crystalline silicon layer on the surface of the ULE substrate. The thinning of the crystalline silicon may be carried out, for example, by chemical mechanical polishing and if necessary or desired, oxidizing the silicon followed by etching to the desired thickness of the silicon.

Investigation of holder pressure and size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator.

PubMed

Aminzahed, Iman; Mashhadi, Mahmoud Mosavi; Sereshk, Mohammad Reza Vaziri

2017-02-01

Micro forming is a manufacturing process to fabricate micro parts with high quality and a cost effective manner. Deep drawing could be a favorable method for production of complicated parts in macro and micro sizes. In this paper piezoelectric actuator is used as a novel approach in the field of micro manufacturing. Also, in current work, investigations are conducted with four rectangular punches and blanks with various thicknesses. Blank holder pressure effects on thickness distributions, punch force, and springback are studied. According to the results of this work, increasing of blank holder pressure in scaled deep drawing, in contrast to thickness of drawn part, leads to decrease in the punch forces and springback. Furthermore, it is shown that in micro deep drawing, the effects of holder pressure on mentioned parameters can be ignored. Copyright © 2016 Elsevier B.V. All rights reserved.

High-throughput automatic defect review for 300mm blank wafers with atomic force microscope

NASA Astrophysics Data System (ADS)

Zandiatashbar, Ardavan; Kim, Byong; Yoo, Young-kook; Lee, Keibock; Jo, Ahjin; Lee, Ju Suk; Cho, Sang-Joon; Park, Sang-il

2015-03-01

While feature size in lithography process continuously becomes smaller, defect sizes on blank wafers become more comparable to device sizes. Defects with nm-scale characteristic size could be misclassified by automated optical inspection (AOI) and require post-processing for proper classification. Atomic force microscope (AFM) is known to provide high lateral and the highest vertical resolution by mechanical probing among all techniques. However, its low throughput and tip life in addition to the laborious efforts for finding the defects have been the major limitations of this technique. In this paper we introduce automatic defect review (ADR) AFM as a post-inspection metrology tool for defect study and classification for 300 mm blank wafers and to overcome the limitations stated above. The ADR AFM provides high throughput, high resolution, and non-destructive means for obtaining 3D information for nm-scale defect review and classification.

Progress on high-performance rapid prototype aluminum mirrors

NASA Astrophysics Data System (ADS)

Woodard, Kenneth S.; Myrick, Bruce H.

2017-05-01

Near net shape parts can be produced using some very old processes (investment casting) and the relatively new direct metal laser sintering (DMLS) process. These processes have significant advantages for complex blank lightweighting and costs but are not inherently suited for producing high performance mirrors. The DMLS process can provide extremely complex lightweight structures but the high residual stresses left in the material results in unstable mirror figure retention. Although not to the extreme intricacy of DMLS, investment casting can also provide complex lightweight structures at considerably lower costs than DMLS and even conventional wrought mirror blanks but the less than 100% density for casting (and also DMLS) limits finishing quality. This paper will cover the progress that has been made to make both the DMLS and investment casting processes into viable near net shape blank options for high performance aluminum mirrors. Finish and figure results will be presented to show performance commensurate with existing conventional processes.

Cold pressure welding of aluminium-steel blanks: Manufacturing process and electrochemical surface preparation

NASA Astrophysics Data System (ADS)

Schmidt, Hans Christian; Homberg, Werner; Orive, Alejandro Gonzalez; Grundmeier, Guido; Hordych, Illia; Maier, Hans Jürgen

2018-05-01

In this study the manufacture of aluminium-steel blanks by cold pressure welding and their preparation for a welding process through electrochemical surface treatment are investigated and discussed. The cold pressure welding process was done with an incremental rolling tool that allows for the partial pressure welding of two blanks along a prepared path. The influence of the surface preparation by electrochemical deposition of bond promoting organosilane-based agents and roughening on a nano-scale is investigated and compared to conventional surface treatments. Coating the surfaces with a thin organosilane-based film incorporating specific functional groups should promote additional bonding between the mating oxide layers; its influence on the total weld strength is studied. Pressure welding requires suitable process strategies, and the current advances in the proposed incremental rolling process for the combination of mild steel and aluminium are presented.

A Regime Legitimacy Explanation of African Peacekeeping

DTIC Science & Technology

2011-09-01

DDR Dearming, Demobilization and Reintegration DRC Democratic Republic of the Congo ECOWAS Economic Community of West African States FAR Forces...Nations Human Development Index xiv THIS PAGE INTENTIONALLY LEFT BLANK 1 I. INTRODUCTION Just 14 years after the genocide of at least a half...increase their moral authority externally by adhering to, or even leading, international norms based on human security. The methodology will be both

Limited Scope Design Study for Multi-Sensor Towbody

DTIC Science & Technology

2016-06-01

FINAL REPORT Limited Scope Design Study for Multi-Sensor Towbody SERDP Project MR-2501 JUNE 2016 Dr. Kevin Williams Tim McGinnis...prepared under contract to the Department of Defense Strategic Environmental Research and Development Program (SERDP). The publication of this...Left Blank REPORT DOCUMENTATION PAGE Standard Form 298 (Rev. 8/98) Prescribed by ANSI Std. Z39.18 Form Approved OMB No. 0704-0188 The public

UAV Swarm Operational Risk Assessment System

DTIC Science & Technology

2015-09-01

a SIPRNET connection. For practicality in development of this prototype, the interface was created using the MATLAB GUI language . By design, the use ...and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE September 2015 3...discrete-event simulation of UAV swarm attacks using ExtendSim, statistical analysis of the simulation data using Minitab, and a graphical user interface

Les Chansons de la Francophonie Web Site and Its Two Web-Usage-Tracking Systems in an Advanced Listening Comprehension Course

ERIC Educational Resources Information Center

Weinberg, Alysse

2005-01-01

The "Les Chansons de la francophonie" web site is based on French songs and was developed using HTML and JavaScript for the advanced French Comprehension Course at the Second Language Institute of the University of Ottawa. These interactive listening activities include true-false and multiple-choice questions, fill in the blanks,…

Tourism in Peru: The Missing Strategy for Economic and Social Development

DTIC Science & Technology

2006-06-01

Lima , 1970-1996.......................................12 xii THIS PAGE INTENTIONALLY LEFT BLANK xiii...time. Not two miles outside of Lima did things not only change, but they changed drastically. High rise buildings, upscale hotels, and very chic...natural resources. This is the case for Peru. Not only does the country hold a wealth of minerals, but it also possesses a plethora of beaches

Training Practices for Surface Warfare Junior Officers

DTIC Science & Technology

2011-12-01

Bowman Alice M . Crawford William D. Hatch December 2011 THIS PAGE INTENTIONALLY LEFT BLANK NAVAL POSTGRADUATE SCHOOL...Alice M . Crawford Assistant Dean for Faculty Development Graduate School of Business & Public Policy William D. Hatch Lecturer Graduate School...NUMBER DRTE9 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) William R. Bowman, Alice M . Crawford, and William D. Hatch 5d. PROJECT

Regional Analysis of Historic Farmstead Archeological Site Characteristics on DoD Installations

DTIC Science & Technology

2014-08-01

Through a previous project, Fort Leonard Wood and ERDC-CERL cultural resource management personnel developed a methodology for efficiently identifying...of Historic Places. This report details testing the applicability of the Fort Leonard Wood methodology to another region of the country. The...This page intentionally left blank.) ERDC/CERL TR-14-11 1 1 Introduction In 2004, Fort Leonard Wood requested the assistance

Development of a Vision-Based Situational Awareness Capability for Unmanned Surface Vessels

DTIC Science & Technology

2017-09-01

used to provide an SA capability for USVs. This thesis addresses the following research questions: (1) Can a computer vision– based technique be...BLANK 51 VI. CONCLUSION AND RECOMMENDATIONS A. CONCLUSION This research demonstrated the feasibility of using a computer vision– based ...VISION- BASED SITUATIONAL AWARENESS CAPABILITY FOR UNMANNED SURFACE VESSELS by Ying Jie Benjemin Toh September 2017 Thesis Advisor: Oleg

Balloon-borne 3-meter telescope for far-infrared and submillimeter astronomy

NASA Technical Reports Server (NTRS)

Fazio, G. G.

1986-01-01

The gimbal design was studied and revised to eliminate the alignment and limited rotation problems inherent in the flex-pivot design. A new design using ball-bearings to replace the flex-pivot was defined and its performance analyzed. An error analysis for the entire gondola pointing system was also prepared. Mirror development and the test program using mirror test blanks from Dornier were continued.

Prototype Development of Low-Cost, Augmented Reality Trainer for Crew Service Weapons

DTIC Science & Technology

2008-09-01

2008 Thesis Co- Advisors : Mathias Kolsch Joseph Sullivan THIS PAGE INTENTIONALLY LEFT BLANK i NSN 7540-01-280-5500 Standard Form 298 (Rev. 2-89...by: Mathias Kölsch Thesis Co- Advisor Joseph Sullivan Thesis Co- Advisor Mathias Kölsch, Ph.D. Chair, MOVES Academic Committee iv...CURRENT QUALIFICATION AND TRAINING METHODS .........9 1. Weapon Qualification / Killer Tomato ..........9 2. Robo -Ski

Electron Beam Freeform Fabrication for Cost Effective Near-Net Shape Manufacturing

NASA Technical Reports Server (NTRS)

Taminger, Karen M.; Hafley, Robert A.

2006-01-01

Manufacturing of structural metal parts directly from computer aided design (CAD) data has been investigated by numerous researchers over the past decade. Researchers at NASA Langley Research Center are developing a new solid freeform fabrication process, electron beam freeform fabrication (EBF3), as a rapid metal deposition process that works efficiently with a variety of weldable alloys. EBF3 deposits of 2219 aluminium and Ti-6Al-4V have exhibited a range of grain morphologies depending upon the deposition parameters. These materials have exhibited excellent tensile properties comparable to typical handbook data for wrought plate product after post-processing heat treatments. The EBF3 process is capable of bulk metal deposition at deposition rates in excess of 2500 cm3/hr (150 in3/hr) or finer detail at lower deposition rates, depending upon the desired application. This process offers the potential for rapidly adding structural details to simpler cast or forged structures rather than the conventional approach of machining large volumes of chips to produce a monolithic metallic structure. Selective addition of metal onto simpler blanks of material can have a significant effect on lead time reduction and lower material and machining costs.

Electron Beam Freeform Fabrication (EBF3) for Cost Effective Near-Net Shape Manufacturing

NASA Technical Reports Server (NTRS)

Taminger, Karen M.; Hafley, Robert A.

2006-01-01

Manufacturing of structural metal parts directly from computer aided design (CAD) data has been investigated by numerous researchers over the past decade. Researchers at NASA Langley Research Center are developing a new solid freeform fabrication process, electron beam freeform fabrication (EBF3), as a rapid metal deposition process that works efficiently with a variety of weldable alloys. EBF3 deposits of 2219 aluminium and Ti-6Al-4V have exhibited a range of grain morphologies depending upon the deposition parameters. These materials have exhibited excellent tensile properties comparable to typical handbook data for wrought plate product after post-processing heat treatments. The EBF3 process is capable of bulk metal deposition at deposition rates in excess of 2500 cubic centimeters per hour (150 in3/hr) or finer detail at lower deposition rates, depending upon the desired application. This process offers the potential for rapidly adding structural details to simpler cast or forged structures rather than the conventional approach of machining large volumes of chips to produce a monolithic metallic structure. Selective addition of metal onto simpler blanks of material can have a significant effect on lead time reduction and lower material and machining costs.

Development of self-forming doxorubicin-loaded polymeric depots as an injectable drug delivery system for liver cancer chemotherapy.

PubMed

Nittayacharn, Pinunta; Nasongkla, Norased

2017-07-01

The objective of this work was to develop self-forming doxorubicin-loaded polymeric depots as an injectable drug delivery system for liver cancer chemotherapy and studied the release profiles of doxorubicin (Dox) from different depot formulations. Tri-block copolymers of poly(ε-caprolactone), poly(D,L-lactide) and poly(ethylene glycol) named PLECs were successfully used as a biodegradable material to encapsulate Dox as the injectable local drug delivery system. Depot formation and encapsulation efficiency of these depots were evaluated. Results show that depots could be formed and encapsulate Dox with high drug loading content. For the release study, drug loading content (10, 15 and 20% w/w) and polymer concentration (25, 30, and 35% w/v) were varied. It could be observed that the burst release occurred within 1-2 days and this burst release could be reduced by physical mixing of hydroxypropyl-beta-cyclodextrin (HP-β-CD) into the depot system. The degradation at the surface and cross-section of the depots were examined by Scanning Electron Microscope (SEM). In addition, cytotoxicity of Dox-loaded depots and blank depots were tested against human liver cancer cell lines (HepG2). Dox released from depots significantly exhibited potent cytotoxic effect against HepG2 cell line compared to that of blank depots. Results from this study reveals an important insight in the development of injectable drug delivery system for liver cancer chemotherapy. Schematic diagram of self-forming doxorubicin-loaded polymeric depots as an injectable drug delivery system and in vitro characterizations. (a) Dox-loaded PLEC depots could be formed with more than 90% of sustained-release Dox at 25% polymer concentration and 20% Dox-loading content. The burst release occurred within 1-2 days and could be reduced by physical mixing of hydroxypropyl-beta-cyclodextrin (HP-β-CD) into the depot system. (b) Dox released from depots significantly exhibited potent cytotoxic effect against human liver cancer cell lines (HepG2 cell line) compared to that of blank depots. (c) Dox-loaded depots showed bulk erosion with hollow core at day 60.

Transcriptome analysis and gene expression profiling of abortive and developing ovules during fruit development in hazelnut.

PubMed

Cheng, Yunqing; Liu, Jianfeng; Zhang, Huidi; Wang, Ju; Zhao, Yixin; Geng, Wanting

2015-01-01

A high ratio of blank fruit in hazelnut (Corylus heterophylla Fisch) is a very common phenomenon that causes serious yield losses in northeast China. The development of blank fruit in the Corylus genus is known to be associated with embryo abortion. However, little is known about the molecular mechanisms responsible for embryo abortion during the nut development stage. Genomic information for C. heterophylla Fisch is not available; therefore, data related to transcriptome and gene expression profiling of developing and abortive ovules are needed. In this study, de novo transcriptome sequencing and RNA-seq analysis were conducted using short-read sequencing technology (Illumina HiSeq 2000). The results of the transcriptome assembly analysis revealed genetic information that was associated with the fruit development stage. Two digital gene expression libraries were constructed, one for a full (normally developing) ovule and one for an empty (abortive) ovule. Transcriptome sequencing and assembly results revealed 55,353 unigenes, including 18,751 clusters and 36,602 singletons. These results were annotated using the public databases NR, NT, Swiss-Prot, KEGG, COG, and GO. Using digital gene expression profiling, gene expression differences in developing and abortive ovules were identified. A total of 1,637 and 715 unigenes were significantly upregulated and downregulated, respectively, in abortive ovules, compared with developing ovules. Quantitative real-time polymerase chain reaction analysis was used in order to verify the differential expression of some genes. The transcriptome and digital gene expression profiling data of normally developing and abortive ovules in hazelnut provide exhaustive information that will improve our understanding of the molecular mechanisms of abortive ovule formation in hazelnut.

Occurrence of Organic Wastewater Contaminants, Pharmaceuticals, and Personal Care Products in Selected Water Supplies, Cape Cod, Massachusetts, June 2004

DTIC Science & Technology

2005-01-01

previously detected high nitrate concen- trations. (Phenol and d- limonene , detected in equipment blanks at unacceptably high concentrations, are not...both tables, were not counted twice. (Phenol and d- limonene , detected in equipment blanks at unaccept- ably high concentrations, are not included in...The surrogate recoveries (not included in table 2) for the PPCP method were 101 and 102 percent. Three compounds, d- limonene , phenol, and

Enhanced Resilience Through Expanded Community Preparedness in the United States: Application of Israeli Models

DTIC Science & Technology

2014-03-01

Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE...INTENTIONALLY LEFT BLANK xviii ACKNOWLEDGMENTS This journey of learning has been shared with many people. I am grateful to my daddy for repeatedly telling...August 3, 2011, http://www.whitehouse.gov/sites/default/files/empowering_local_ partners.pdf. 2 Ted Lewis, “The Book of Extremes, Why the 21st Century

The Impact of Threat Perception Disparities on ROK-U.S. Alliance Cohesion: Shifts Between Self-Reliance and Troop Dispatches in the Park and Roh Administrations

DTIC Science & Technology

2017-12-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release. Distribution is unlimited. THE IMPACT OF...by Youngju Jeong December 2017 Thesis Advisor: Robert Weiner Second Reader: Tristan Mabry THIS PAGE INTENTIONALLY LEFT BLANK i REPORT...20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE December 2017 3. REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE THE

Modular Multi-Sensor Display System Design Study. Volume 2. Detail Design and Application Analysis

DTIC Science & Technology

1974-08-01

control grid . 2. Horizontal AFC/Deflection Module - Generates horizontal sweep signals from input syncs to provide 525 to 1023 line television raster...separation, and gener- ate composite blanking for the CRT control grid . Signal Number of Lines Signal Type Characteristics Input Interface Composite...SEPERATOR DC RESTORA- TION l_i BLANKING VERT DRIVE ■♦ Bl" CRT " CATHODE * _fc> BRIGHTNESS ^ (FRONT PANEL) .CRT GRID ■♦• COMP SYNC Figure

Observations and Modeling of Upper Ocean Hydrography in the Western Arctic With Implications for Acoustic Propagation

DTIC Science & Technology

2016-12-01

2016 Dissertation Supervisors: Wieslaw Maslowski John Colosi THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved...level is 4% of the standard GM value. Frequency spectra of spice show a form similar to the internal-wave spectra but with a steeper spectral slope...Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release

Transnational Organized Crime and New Terrorism in Sri Lanka: A Nexus

DTIC Science & Technology

2017-12-01

Second Reader: Feroz Khan THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting...ABSTRACT UU NSN 7540–01-280-5500 Standard Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii...significant differences from traditional (old) terrorism; this new form “promotes an uncompromising view of the world in accordance with religious beliefs

The Rajah Solaiman Islamic Movement (RSIM) and the Rise of Radical Islamic Converts in the Philippines: A Major Security Concern

DTIC Science & Technology

2008-06-01

Northern Philippines where, like the MILF’s Camp Abu Bakar in Mindanao, Muslims could practice the true teachings of Islam (personal communication...Nayve Jr. June 2008 Thesis Advisor: Douglas Borer Second Reader: Sean Everton THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE...ONLY (Leave blank) 2. REPORT DATE June 2008 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE The Rajah Solaiman

External quality assurance project report for the National Atmospheric Deposition Program’s National Trends Network and Mercury Deposition Network, 2013–14

USGS Publications Warehouse

Wetherbee, Gregory A.; Martin, RoseAnn

2016-07-05

The Mercury Deposition Network programs include the system blank program and an interlaboratory comparison program. System blank results indicated that maximum total mercury contamination concentrations in samples were less than the third percentile of all Mercury Deposition Network sample concentrations. The Mercury Analytical Laboratory produced chemical concentration results with low bias and variability compared with other domestic and international laboratories that support atmospheric-deposition monitoring.

GC-MS and LC-MS analysis of nerve agents in body fluids: intra-laboratory verification test using spiked plasma and urine samples.

PubMed

Koller, Marianne; Becker, Christian; Thiermann, Horst; Worek, Franz

2010-05-15

The purpose of this study was to check the applicability of different analytical methods for the identification of unknown nerve agents in human body fluids. Plasma and urine samples were spiked with nerve agents (plasma) or with their metabolites (urine) or were left blank. Seven random samples (35% of all samples) were selected for the verification test. Plasma was worked up for unchanged nerve agents and for regenerated nerve agents after fluoride-induced reactivation of nerve agent-inhibited butyrylcholinesterase. Both extracts were analysed by GC-MS. Metabolites were extracted from plasma and urine, respectively, and were analysed by LC-MS. The urinary metabolites and two blank samples could be identified without further measurements, plasma metabolites and blanks were identified in six of seven samples. The analysis of unchanged nerve agent provided five agents/blanks and the sixth agent after further investigation. The determination of the regenerated agents also provided only five clear findings during the first screening because of a rather noisy baseline. Therefore, the sample preparation was extended by a size exclusion step performed before addition of fluoride which visibly reduced baseline noise and thus improved identification of the two missing agents. The test clearly showed that verification should be performed by analysing more than one biomarker to ensure identification of the agent(s). Copyright (c) 2010 Elsevier B.V. All rights reserved.

Hydrogeologic and chemical data for the O-Field area, Aberdeen Proving Ground, Maryland

USGS Publications Warehouse

Nemoff, P.R.; Vroblesky, D.A.

1989-01-01

O-Field, located at the Edgewood area of Aberdeen Proving Ground , Maryland, was periodically used for disposal of munitions, waste chemicals, and chemical-warfare agents from World War II through the 1950' s. This report includes various physical, geologic, chemical, and hydrologic data obtained from well-core, groundwater, surface water, and bottom-sediment sampling sites at and near the O-Field disposal area. The data are presented in tables and hydrographs. Three site-location maps are also included. Well-core data include lithologic logs for 11 well- cluster sites, grain-size distributions, various chemical characteristics, and confining unit characteristics. Groundwater data include groundwater chemistry, method blanks for volatile organic carbon, available data on volatile and base/neutral organics, and compilation of corresponding method blanks, chemical-warfare agents, explosive-related products, radionuclides, herbicides, and groundwater levels. Surface-water data include field-measured characteristics; concentrations of various inorganic constituents including arsenic; selected organic constituents with method blanks; detection limits of organics; and a compilation of information on corresponding acids, volatiles, and semivolatiles. Bottom- sediment data include inorganic properties and constituents; organic chemistry; detection limits for organic chemicals; a compilation of information on acids, volatiles, and semivolatiles; and method blanks corresponding to acids, volatiles, and semivolatiles. A set of 15 water- level hydrographs for the period March 1986 through September 1987 also is included in the report. (USGS)

Effects of microRNA-21 on Nerve Cell Regeneration and Neural Function Recovery in Diabetes Mellitus Combined with Cerebral Infarction Rats by Targeting PDCD4.

PubMed

Guo, Yun-Bao; Ji, Tie-Feng; Zhou, Hong-Wei; Yu, Jin-Lu

2018-03-01

We aimed to determine the effect and mechanism of microRNA-21 (miR-21) on nerve cell regeneration and nerve functional recovery in diabetes mellitus combined with cerebral infarction (DM + CI) rats by targeting PDCD4. A total of 125 male Wistar rats were selected for DM + CI rat model construction and assigned into the blank, miR-21 mimics, mimics control, miR-21 inhibitor, inhibitor control, miR-21 inhibitor + si-PDCD4 and si-PDCD4 groups. And, 20 healthy rats were selected for the normal group. Triphenylterazolium chloride (TTC) staining and HE staining were used for determination of the area of CI and pathological changes, respectively. Behaviors of rats in the eight groups were determined by forelimb placement test and balance beam walking test. Immunohistochemical staining, double immunofluorescence staining assay, Western blotting, and qRT-PCR were used to detect expressions of miR-21, PDCD4, HNA, Nestin, NeuN, β-III-Tub, PTEN, FasL, and GFAP. DNA laddering and TUNEL staining was used for cell apoptosis. TTC and HE staining confirmed that 87.5% rats were induced into CI + DM models successfully. Results of forelimb placement test and balance beam walking test showed that miR-21 mimics, and si-PCDC4 improved the nerve defect of model rats. Comparing with the blank group at the same time, rats in the miR-21 inhibitor group displayed significant decrease in the forelimb placement test score, significant increase in the balance beam walking test score, and exacerbation of nerve defect, while rats in the miR-21 mimics and si-PCDC4 groups displayed significant increase in forelimb placement test score and significant decrease in the balance beam walking test score and improvement of nerve defect situation. The HNA, Nestin, and PDCD4 expressions were decreased and the NeuN, β-III-Tub, and GFAP expressions were increased in the miR-21 mimics and si-PDCD4 groups comparing with the blank group. The results of miR-21 inhibitor group were on the contrary. In comparison to the blank group, the miR-21 mimics group and the si-PDCD4 had lower miR-21 expressions and higher expressions of PDCD4, PTEN, and FasL, while the miR-21 inhibitor group was in the opposite trend. The results of qRT-PCR were the same with Western blotting. The expressions of fluorescence in other groups were higher than the normal group; compared with the blank group, the miR-21 mimics group and the si-PDCD4 group had lower fluorescence expression and DNA ladder. However, the fluorescence expressions and DNA ladder of miR-21 inhibitor group increased markedly in contrast with the blank group. Comparing with the blank group, BrdU + /DEX + fluorescence intensity significantly enhanced in the miR-21 mimics and si-PDCD4 groups and significantly reduced in the miR-21 inhibitor group. And, comparing with the blank group, in the miR-21 mimics group, the signal strength of luciferase carrying the wild-type PDCD4 was reduced by 25%. The present studies demonstrated that miR-21 could promote the nerve cell regeneration, suppress apoptosis of nerve cells in DM + CI rats and improves the nerve defect situation of DM + CI rats by inhibiting PDCD4.

A study on thick plate forming for hollow-partitioned steam turbine nozzle

NASA Astrophysics Data System (ADS)

Kwak, Bong-Seok; Kang, Byeong-Kwon; Yoon, Mahn-Jung; Jeon, Jae-Young; Kang, Beom-Soo; Ku, Tae-Wan

2017-10-01

In thermal and nuclear power plants, steam turbine system to generate electric power is composed of turbine rotor assemblies for high-pressure (HP) and low-pressure (LP) turbines, its main shaft, and turbine nozzle diaphragms, and so forth. Especially, the turbine nozzle diaphragm consists of many turbine nozzles with three-dimensional asymmetric shape and complicated surface curvatures at each turbine stage. In this study, main goal is tool design and fabrication, and its application to thick plate cold forming for replacing solid-type turbine nozzle manufactured by a series of metal forging process with hollow-partitioned one obtained from cold forming. The hollow-partitioned turbine nozzle (stator) has asymmetric curvature contours, so it is hard to adopt a series of draw-bead or blank holder. Thus, the thick plate as a thick blank experiences unstable and non-uniform contact on the tool surfaces in the die cavity. To easy this unstable positioning restraint in the thick plate forming, the shoulder angles of the forming punch and the lower die are selected as the geometric process parameter to control the blank position in the die cavity. The thick plate material is 409L stainless steel (SUS409L) with initial thickness of 5.00mm, and the dimensions are a length of about 980.00mm and a width of roughly 372.60mm. Uni-axial tensile tests for the initial blank material of SUS409L are performed to verify the mechanical properties including the anisotropic characteristics, and finite element simulations are carried out using ABAQUS Explicit/Implicit. As the obtained and summarized results, the suitable shoulder angle combinations of the lower die and the punch were verified as (30°, 90°) and (45°, 90°), and then the transverse blank direction (TD) of SUS409L thick plate was investigated to be well matched.

Overexpression of SASH1 related to the decreased invasion ability of human glioma U251 cells.

PubMed

Yang, Liu; Liu, Mei; Gu, Zhikai; Chen, Jianguo; Yan, Yaohua; Li, Jian

2012-12-01

The purpose of this study was to investigate the impact of SAM- and SH3-domain containing 1 (SASH1) on the biological behavior of glioma cells, including its effects on cellular growth, proliferation, apoptosis, invasion, and metastasis, and thereby to provide an experimental basis for future therapeutic treatments. A pcDNA3.1-SASH1 eukaryotic expression vector was constructed and transfected into the U251 human glioma cell line. Using the tetrazolium-based colorimetric (MTT) assay, flow cytometry analyses, transwell invasion chamber experiments, and other methods, we examined the impact of SASH1 on the biological behaviors of U251 cells, including effects on viability, cell cycle, apoptosis, and invasion. Furthermore, the effect of SASH1 on the expression of cyclin D1, caspase-3, matrix metalloproteinase (MMP)-2, MMP-9, and other proteins was observed. Compared to the empty vector and blank control groups, the pcDNA3.1-SASH1 group of U251 cells exhibited significantly reduced cell viability, proliferation, and invasion (p < 0.05), although there was no difference between the empty vector and blank control groups. The pcDNA3.1-SASH1 group demonstrated a significantly higher apoptotic index than did the empty vector and blank control groups (p < 0.05), and the percentage of apoptotic cells was similar between the empty vector and blank control groups. In addition, the pcDNA3.1-SASH1 group expressed significantly lower protein levels of cyclin D1 and MMP-2/9 compared to the control and empty vector groups (p < 0.05) and significantly higher protein levels of caspase-3 than the other two groups (p < 0.05). Cyclin D1, caspase-3, and MMP-2/9 expression was unchanged between the empty vector and blank control groups. SASH1 gene expression might be related to the inhibition of the growth, proliferation, and invasion of U251 cells and the promotion of U251 cells apoptosis.

Support optimization of the ring primary mirror of a 2m solar telescope

NASA Astrophysics Data System (ADS)

Yang, Dehua; Jin, Zhenyu; Liu, Zhong

2016-08-01

A special 2-m Ring Solar Telescope (2-m RST) is to be built by YNAO-Yunnan Astronomical Observatory, Kunming, China. Its distinct primary mirror is distinctively shaped in a ring with an outer diameter of 2.02 m and a ring width of 0.35 m. Careful calculation and optimization of the mirror support pattern have been carried out first of all to define optimum blank parameters in view of performance balance of support design, fabrication and cost. This paper is to review the special consideration and optimization of the support design for the unique ring mirror. Schott zerodur is the prevailing candidate for the primary mirror blank. Diverse support patterns with various blank thicknesses have been discussed by extensive calculation of axial support pattern of the mirror. We reached an optimum design of 36 axial supports for a blank thickness of 0.15 m with surface error of 5 nm RMS. Afterwards, lateral support scheme was figured out for the mirror with settled parameters. A classical push-and-pull scheme was used. Seeing the relative flexibility of the ring mirror, special consideration was taken to unusually set the acting direction of the support forces not in the mirror gravity plane, but along the gravity of the local virtual slices of the mirror blank. Nine couples of the lateral push-pull force are considered. When pointing to horizon, the mirror surface exhibits RMS error of 5 nm with three additional small force couples used to compensate for the predominant astigmatism introduced by lateral supports. Finally, error estimation has been performed to evaluate the surface degradation with introduced errors in support force and support position, respectively, for both axial and lateral supports. Monte Carlo approach was applied using unit seeds for amplitude and position of support forces. The comprehensive optimization and calculation suggests the support systems design meet the technic requirements of the ring mirror of the 2-m RST.

Cloud property datasets retrieved from AVHRR, MODIS, AATSR and MERIS in the framework of the Cloud_cci project

NASA Astrophysics Data System (ADS)

Stengel, Martin; Stapelberg, Stefan; Sus, Oliver; Schlundt, Cornelia; Poulsen, Caroline; Thomas, Gareth; Christensen, Matthew; Carbajal Henken, Cintia; Preusker, Rene; Fischer, Jürgen; Devasthale, Abhay; Willén, Ulrika; Karlsson, Karl-Göran; McGarragh, Gregory R.; Proud, Simon; Povey, Adam C.; Grainger, Roy G.; Fokke Meirink, Jan; Feofilov, Artem; Bennartz, Ralf; Bojanowski, Jedrzej S.; Hollmann, Rainer

2017-11-01

New cloud property datasets based on measurements from the passive imaging satellite sensors AVHRR, MODIS, ATSR2, AATSR and MERIS are presented. Two retrieval systems were developed that include components for cloud detection and cloud typing followed by cloud property retrievals based on the optimal estimation (OE) technique. The OE-based retrievals are applied to simultaneously retrieve cloud-top pressure, cloud particle effective radius and cloud optical thickness using measurements at visible, near-infrared and thermal infrared wavelengths, which ensures spectral consistency. The retrieved cloud properties are further processed to derive cloud-top height, cloud-top temperature, cloud liquid water path, cloud ice water path and spectral cloud albedo. The Cloud_cci products are pixel-based retrievals, daily composites of those on a global equal-angle latitude-longitude grid, and monthly cloud properties such as averages, standard deviations and histograms, also on a global grid. All products include rigorous propagation of the retrieval and sampling uncertainties. Grouping the orbital properties of the sensor families, six datasets have been defined, which are named AVHRR-AM, AVHRR-PM, MODIS-Terra, MODIS-Aqua, ATSR2-AATSR and MERIS+AATSR, each comprising a specific subset of all available sensors. The individual characteristics of the datasets are presented together with a summary of the retrieval systems and measurement records on which the dataset generation were based. Example validation results are given, based on comparisons to well-established reference observations, which demonstrate the good quality of the data. In particular the ensured spectral consistency and the rigorous uncertainty propagation through all processing levels can be considered as new features of the Cloud_cci datasets compared to existing datasets. In addition, the consistency among the individual datasets allows for a potential combination of them as well as facilitates studies on the impact of temporal sampling and spatial resolution on cloud climatologies.

For each dataset a digital object identifier has been issued:

Cloud_cci AVHRR-AM: https://doi.org/10.5676/DWD/ESA_Cloud_cci/AVHRR-AM/V002

Cloud_cci AVHRR-PM: https://doi.org/10.5676/DWD/ESA_Cloud_cci/AVHRR-PM/V002

Cloud_cci MODIS-Terra: https://doi.org/10.5676/DWD/ESA_Cloud_cci/MODIS-Terra/V002

Cloud_cci MODIS-Aqua: https://doi.org/10.5676/DWD/ESA_Cloud_cci/MODIS-Aqua/V002

Cloud_cci ATSR2-AATSR: https://doi.org/10.5676/DWD/ESA_Cloud_cci/ATSR2-AATSR/V002

Cloud_cci MERIS+AATSR: https://doi.org/10.5676/DWD/ESA_Cloud_cci/MERIS+AATSR/V002

[Cynomorium songaricum improves sperm count and motility and serum testosterone level and promotes proliferation of undifferentiated spermatogonia in oligoasthenospermia rats].

PubMed

Cao, Yi-Juan; Li, Zhen-Bei; Qi, Yu-Juan; Liu, Ying; Gu, Juan; Hu, Fang-Fang; Zhang, Wen-da; Hao, Lin; Hou, Jian-Quan; Han, Cong-Hui

2016-12-01

To investigate the effects of cynomorium songaricum (CS) decoction on the testis weight, serum testosterone level, and sperm parameters of rats with oligoasthenospermia (OAS), explore its action mechanism of improving the proliferation of undifferentiated spermatogonial cells, and provide some experimental and theoretical evidence for the development of new Chinese drugs for OAS. Thirty 8-week-old male SD rats were randomly divided into five groups of equal number: blank control, model control, high-dose CS, medium-dose CS, and low-dose CS. OAS models were established by intraperitoneal injection of cyclophosphamide and, a month later, treated intragastrically with normal saline or CS at 2, 1, and 0.5 g per kg of the body weight per day, all for 4 weeks. Then, the testes of the animals were harvested to obtain the testicular weight, sperm concentration and motility, and the level of serum testosterone (T), detect the expressions of the transcription factor 1 (Oct4), Thy-1 cell surface antigen (Thy1), promyelocytic leukemia zinc finger (PLZF), KIT proto-oncogene receptor tyrosine kinase (C-kit) and glial cell-derived neurotrophic factor (GDNF) in the testis tissue of the rats in the low-dose CS group by real-time PCR. The testis weights in the blank control, model control, high-dose CS, medium-dose CS, and low-dose CS groups were (1.52±0.06), (1.55±0.06), (1.43±0.30), (1.35±0.40) and (1.34±0.04) g, respectively, not significantly different in the blank and model controls from those in the CS groups (P>0.05). The visual field sperm count per 10 HP was significantly increased in the high-, medium-, and low-dose CS groups (202±20, 196±5 and 216±25) as compared with the blank and model controls (200±15 and 134±30) (P<0.05). The mRNA expressions of the Oct4, Thy1, PLZF and GDNF genes were remarkably higher in the low-dose CS group than in the controls (P<0.05), but that of the C-kit gene showed no significant difference from the latter (P>0.05). The visual field sperm motility per 10 HP was markedly increased in the blank control (［52.1±5.5］%), model control (［38.1±2.5］%), high-dose CS (［59.1±9.5］%), medium-dose CS (［58.7±9.5］%), and low-dose CS (［49.6±1.0］%) groups, and so was the level of serum testosterone (［190±87.5］, ［82.5±25.8］, ［229±75.6］, ［331±86.7］ and ［185±82.4］ mmol/L), both remarkably higher in the CS groups than in the model controls (P<0.05) but with no statistically significant difference between the CS groups and the blank controls (P>0.05). CS can significantly improve sperm concentration, sperm motility and serum T level in OAS rats, probably by inducing the expression of GDNF in the rat Sertoli cells, promoting the proliferation of undifferentiated spermatogonial cells, and enhancing spermatogenesis.

The Development of an Officer Training School Board Score Prediction Method Using a Multi-Board Approach

DTIC Science & Technology

1991-03-01

forms: ". ..application blanks, biographical inventories , interviews, work sample tests, and intelligence, aptitude, and personality tests" (1:11...the grouping method, 3) the task method, and 4) the knowledge , skills, abilities (KSA) method. The point method of measuring training/experience assigns... knowledge , skills, abilities, and other characteristics which relate specifically to each job element (3:131). Interview. According to N. Schmitt

Eliminating Fear of the Blank Page: A Thematic Approach, aka Squeezing the California Department of Education's 1992 ESL Model Standards for Adult Education Programs into One Tidy Package.

ERIC Educational Resources Information Center

DesRoches, Diane

An approach to teaching integrated language skills in adult English-as-a-Second-Language (ESL) instruction is described. The technique uses a combination of classroom drama and role-playing, writing about the event, revision, publication, and follow-up activities to develop speaking, listening, reading, and writing skills. Eight stages are defined…

Optimization of Microgrids at Military Remote Base Camps

DTIC Science & Technology

2017-12-01

DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this collection of information is estimated to average 1 hour per... Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 i THIS PAGE INTENTIONALLY LEFT BLANK ii Approved for public release. Distribution is unlimited...Operational Energy Office Initiatives Quickly after establishment, the newly formed Operational Energy Office developed a list of initiatives aimed

News and Views: LSST mirror blank; More and better maths; Free telescopes; The hurricane season is starting again Get ready: IYA2009 UK website up and running

NASA Astrophysics Data System (ADS)

2008-10-01

As floods and hurricanes disrupt the lives of people round the world, a new generation of scientific tools are supporting both storm preparedness and recovery. As International Year of Astronomy 2009 approaches, the UK website is developing more features that make it easier to see what's planned for this science extravaganza.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, Elizabeth James Kistin; Warren, Drake; Hess, Marguerite Evelyn

This study examines the structure and impact of state-funded technology maturation programs that leverage research institutions for economic development throughout the United States. The lessons learned and practices identified from previous experiences will inform Sandia National Laboratories' Government Relations and Technology Partnerships teams as they participate in near-term discussions about the proposed Technology Readiness Gross Receipts Tax Credit and Program, and continue to shape longer-term program and partnership opportunities. This Page Intentionally Left Blank

Costs and Benefits of Software Process Improvement

DTIC Science & Technology

1997-12-01

Washington, DC 20503. 1. AGENCY USE ONLY ( Leave blank) 2. REPORT DATE December 1997 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4...in this field, an organization’s chance for success depends first on having an exceptional manager and an effective development team (PEOPLE...Secondly, it depends on its effective use of TECHNOLOGY, and finally, on its PROCESS maturity. [Ref. 4] In a software organization: PEOPLE refers to

Developing of Library for Proofs of Data Possession in Charm

DTIC Science & Technology

2013-06-01

INTENTIONALLY LEFT BLANK x LIST OF ACRONYMS AND ABBREVIATIONS API Application Programmer Interface DTP Datatype -preserving Encryption FedRAMP U.S...proposed block-cipher mode for Datatype -Preserving Encryption (DTP) uses the Knuth Shuffle in one of its steps [19]. It may be advantageous to...http://www.clustal.org/omega/clustalo-api/util_8c.html. [19] U. T. Mattsson, “Format-controlling encryption using datatype -preserving encryption

Decreasing Skin Graft Contraction through Topical Wound Bed Preparation with Anti-Inflammatory Agents

DTIC Science & Technology

2016-10-01

inflammatory agents - Wound healing -Contraction ACCOMPLISHMENTS: What were the major goals of the project? Develop treatments that modulate...1 AD _____________________ (Leave blank) Award Number: W81XWH-14-2-0153 TITLE: Decreasing Skin Graft Contraction through Topical Wound Bed...TYPE Annual 3. DATES COVERED (From - To) 15 Sep 2015 - 14 Sep 2016 4. TITLE AND SUBTITLE Decreasing Skin Graft Contraction through Topical Wound Bed

Prototypes of Cognitive Measures for Air Force Officers: Test Development and Item Banking

DTIC Science & Technology

1990-05-01

with the complexity of the relationship. Relationships may be in terms of shape, size, dimensionality, area of embeddedness , rotation, blank/shaded...administration were used. Test directions were read from the booklet. Demographics and test responses were recorded on a machine-scannable answer sheet...as demographic information would be needed to determine whether sample characteristics accounted for the differences in mean scores for NC, FA, and WD

The EPIC-MOS Particle-Induced Background Spectrum

NASA Technical Reports Server (NTRS)

Kuntz, K. D.; Snowden, S. L.

2006-01-01

We have developed a method for constructing a spectrum of the particle-induced instrumental background of the XMM-Newton EPIC MOS detectors that can be used for observations of the diffuse background and extended sources that fill a significant fraction of the instrument field of view. The strength and spectrum of the particle-induced background, that is, the background due to the interaction of particles with the detector and the detector surroundings, is temporally variable as well as spatially variable over individual chips. Our method uses a combination of the filter-wheel-closed data and a database of unexposed-region data to construct a spectrum of the "quiescent" background. We show that, using this method of background subtraction, the differences between independent observations of the same region of "blank sky" are consistent with the statistical uncertainties except when there is clear evidence of solar wind charge exchange emission. We use the blank sky observations to show that contamination by SWCX emission is a strong function of the solar wind proton flux, and that observations through the flanks of the magnetosheath appear to be contaminated only at much higher solar wind fluxes. We have also developed a spectral model of the residual soft proton flares, which allows their effects to be removed to a substantial degree during spectral fitting.

Development of hybrid scaffolds using ceramic and hydrogel for articular cartilage tissue regeneration.

PubMed

Seol, Young-Joon; Park, Ju Young; Jeong, Wonju; Kim, Tae-Ho; Kim, Shin-Yoon; Cho, Dong-Woo

2015-04-01

The regeneration of articular cartilage consisting of hyaline cartilage and hydrogel scaffolds has been generally used in tissue engineering. However, success in in vivo studies has been rarely reported. The hydrogel scaffolds implanted into articular cartilage defects are mechanically unstable and it is difficult for them to integrate with the surrounding native cartilage tissue. Therefore, it is needed to regenerate cartilage and bone tissue simultaneously. We developed hybrid scaffolds with hydrogel scaffolds for cartilage tissue and with ceramic scaffolds for bone tissue. For in vivo study, hybrid scaffolds were press-fitted into osteochondral tissue defects in a rabbit knee joints and the cartilage tissue regeneration in blank, hydrogel scaffolds, and hybrid scaffolds was compared. In 12th week after implantation, the histological and immunohistochemical analyses were conducted to evaluate the cartilage tissue regeneration. In the blank and hydrogel scaffold groups, the defects were filled with fibrous tissues and the implanted hydrogel scaffolds could not maintain their initial position; in the hybrid scaffold group, newly generated cartilage tissues were morphologically similar to native cartilage tissues and were smoothly connected to the surrounding native tissues. This study demonstrates hybrid scaffolds containing hydrogel and ceramic scaffolds can provide mechanical stability to hydrogel scaffolds and enhance cartilage tissue regeneration at the defect site. © 2014 Wiley Periodicals, Inc.

Development of a method for the determination of Fusarium fungi on corn using mid-infrared spectroscopy with attenuated total reflection and chemometrics.

PubMed

Kos, Gregor; Lohninger, Hans; Krska, Rudolf

2003-03-01

A novel method, which enables the determination of fungal infection with Fusarium graminearum on corn within minutes, is presented. The ground sample was sieved and the particle size fraction between >250 and 100 microm was used for mid-infrared/attenuated total reflection (ATR) measurements. The sample was pressed onto the ATR crystal, and reproducible pressure was applied. After the spectra were recorded, they were subjected to principle component analysis (PCA) and classified using cluster analysis. Observed changes in the spectra reflected changes in protein, carbohydrate, and lipid contents. Ergosterol (for the total fungal biomass) and the toxin deoxynivalenol (DON; a secondary metabolite) of Fusarium fungi served as reference parameters, because of their relevance for the examination of corn based food and feed. The repeatability was highly improved by sieving prior to recording the spectra, resulting in a better clustering in PCA score/score plots. The developed method enabled the separation of samples with a toxin content of as low as 310 microg/kg from noncontaminated (blank) samples. Investigated concentration ranges were 880-3600 microg/kg for ergosterol and 310-2596 microg/kg for DON. The percentage of correctly classified samples was up to 100% for individual samples compared with a number of blank samples.

Ecological landscape elements: long-term monitoring in Great Britain, the Countryside Survey 1978-2007 and beyond

NASA Astrophysics Data System (ADS)

Wood, Claire M.; Bunce, Robert G. H.; Norton, Lisa R.; Maskell, Lindsay C.; Smart, Simon M.; Scott, W. Andrew; Henrys, Peter A.; Howard, David C.; Wright, Simon M.; Brown, Michael J.; Scott, Rod J.; Stuart, Rick C.; Watkins, John W.

2018-04-01

The Countryside Survey (CS) of Great Britain (GB) provides a unique and statistically robust series of datasets, consisting of an extensive set of repeated ecological measurements at a national scale, covering a time span of 29 years. CS was first undertaken in 1978 to provide a baseline for ecological and land use change monitoring in the rural environment of GB, following a stratified random design, based on 1 km squares. Originally, eight random 1 km squares were drawn from each of 32 environmental classes, thus comprising 256 sample squares in the 1978 survey. The number of these sites increased to 382 in 1984, 506 in 1990, 569 in 1998 and 591 in 2007. Detailed information regarding vegetation types and land use was mapped in all five surveys, allowing reporting by defined standard habitat classifications. Additionally, point and linear landscape features (such as trees and hedgerows) are available from all surveys after 1978. From these stratified, randomly located sample squares, information can be converted into national estimates, with associated error terms. Other data, relating to soils, freshwater and vegetation, were also sampled on analogous dates. However, the present paper describes only the surveys of landscape features and habitats. The resulting datasets provide a unique, comprehensive, quantitative ecological coverage of extent and change in these features in GB. Basic results are presented and their implications discussed. However, much opportunity for further analyses remains. Data from each of the survey years are available via the following DOIs: Landscape area data 1978: https://doi.org/10.5285/86c017ba-dc62-46f0-ad13-c862bf31740e, 1984: https://doi.org/10.5285/b656bb43-448d-4b2c-aade-7993aa243ea3, 1990: https://doi.org/10.5285/94f664e5-10f2-4655-bfe6-44d745f5dca7, 1998: https://doi.org/10.5285/1e050028-5c55-42f4-a0ea-c895d827b824, and 2007: https://doi.org/10.5285/bf189c57-61eb-4339-a7b3-d2e81fdde28d; Landscape linear feature data 1984: https://doi.org/10.5285/a3f5665c-94b2-4c46-909e-a98be97857e5, 1990: https://doi.org/10.5285/311daad4-bc8c-485a-bc8a-e0d054889219, 1998: https://doi.org/10.5285/8aaf6f8c-c245-46bb-8a2a-f0db012b2643 and 2007: https://doi.org/10.5285/e1d31245-4c0a-4dee-b36c-b23f1a697f88, Landscape point feature data 1984: https://doi.org/10.5285/124b872e-036e-4dd3-8316-476b5f42c16e, 1990: https://doi.org/10.5285/1481bc63-80d7-4d18-bcba-8804aa0a9e1b, 1998: https://doi.org/10.5285/ed10944f-40c8-4913-b3f5-13c8e844e153 and 2007: https://doi.org/10.5285/55dc5fd7-d3f7-4440-b8a7-7187f8b0550b.

Life-Cycle Cost Modeling to Determine Whether Vehicle-to-Grid (V2G) Integration and Ancillary Service Revenue Can Generate a Viable Case for Plug-In Electric Drive Vehicles

DTIC Science & Technology

2013-09-01

LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this collection of information is estimated to...information, including suggestions for reducing this burden, to Washington headquarters Services, Directorate for Information Operations and Reports ...0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE September 2013 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4

Rising Tides: The Strategic Importance of the Black Sea and Romania for U.S. Naval Strategy

DTIC Science & Technology

2017-06-01

Abenheim Second Reader: Mikhail Tsypkin THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public... Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release...play. Articles from well-informed foreign and domestic news agencies will also be utilized to form a basis of the perceptions of actors in the area

Hardware Photos: Image Showing JWST Engineering Demonstration Mirror, Mounted Ready for Machining at AXYS and Image Showing HIP Can Containing Light Mirrors 1 and 2 Ready for Mirror Fabrication

NASA Technical Reports Server (NTRS)

OKeefe, Sean

2004-01-01

The images in this viewgraph presentation have the following captions: 1) EDU mirror after being sawed in half; 2) EDU Delivered to Axsys; 3) Be EDU Blank Received and Machining Started; 4) Loaded HIP can for flight PM segments 1 and 2; 5) Flight Blanks 1 and 2 Loaded into HIP Can at Brush-Wellman; 6) EDU in Machining at Axsys.

Generating GraphML XML Files for Graph Visualization of Architectures and Event Traces for the Monterey Phoenix Program

DTIC Science & Technology

2012-09-01

Thesis Advisor: Mikhail Auguston Second Reader: Terry Norbraten THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved...Language (GraphML). MPGrapher compiles well- formed XML files that conform to the yEd GraphML schema. These files will be opened and analyzed using...ABSTRACT UU NSN 7540-01-280-5500 Standard Form 298 (Rev. 2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved

Quantum Chemical and Physicochemical Studies of Oximes (Prophylactics against and Reactivators of Phosphorylated AChE).

DTIC Science & Technology

1984-10-25

crystal structure of nicotinic acid ,. and we used the ether bridge from the crystal structure of dimethyl ether. We are investigating various rotamers...observations were made: - The titration curve (after the subtraction of the blank curve) shows only one titrable group, i.e. the oxime moiety. - The...subtraction of the blank curve, shows two titrable groups, i.e. the two oxime moieties. The results are as follows: Temperature Conditions PKa pK2

Design Guidelines for the User Interface to Computer-Based Information Systems

DTIC Science & Technology

1983-03-01

Marshall and Alderman, 1981. See also: Section 3.1.3. -22 Single Keying for Alphabetic Data -22 When alphabetic data entry is required, the user should be...distinction between single and multiple blanks in data entry; in particular, the user should not have to count blanks. Comment: People cannot be relied upon...logically related items should be accomplished by a single , explicit action at the end, rather than by separate entry of each item. Comment: This practice

Simultaneous detection of residues of 25 β₂-agonists and 23 β-blockers in animal foods by high-performance liquid chromatography coupled with linear ion trap mass spectrometry.

PubMed

Sai, Fan; Hong, Miao; Yunfeng, Zhao; Huijing, Chen; Yongning, Wu

2012-02-29

A sensitive method has been developed for the simultaneous determination of residues of 25 β₂-agonists and 23 β-blockers in animal foods by high-performance liquid chromatography coupled with linear ion trap mass spectrometry (HPLC-LIT-MS). This method is based on a new procedure of hydrolysis and extraction by 5% trichloracetic acid, and then cleaned up by mixed strong cation exchange (MCX) cartridges coupled with a novelty cleanup step by methanol. Methanol and 0.1% formic acid were used as mobile phases for gradient elution, while a Supelco Ascentis Express Rp-Amide column was used for LC separation. ESI positive ion scan mode was used with consecutive reaction monitoring (CRM, MS³). Nine β₂-agonists labeled by the deuterium isotope were used as internal standards for quantification. The linear ranges of 48 analytes were from 5 to 200 μg/L; the coefficient of correlation was not less than 0.995. Blank pork muscle, blank liver, and blank kidney were selected as representative matrix for spiked standard recovery test. The recoveries of each compound were in the range of 46.6-118.9%, and the relative standard deviations were in the range of 1.9-28.2%. Decision limits (CCα, α = 0.01) of 48 analytes in muscles, liver, and kidney samples ranged from 0.05 to 0.49 μg/kg, and the detection capability (CCβ, β = 0.05) ranged from 0.13 to 1.64 μg/kg. This method was successfully applied to 110 real animal origin food samples including meat, liver, and kidney of pig and chicken samples.

First insights into the protective effects of a recombinant swinepox virus expressing truncated MRP of Streptococcus suis type 2 in mice.

PubMed

Huang, Dongyan; Zhu, Haodan; Lin, Huixing; Xu, Jiarong; Lu, Chengping

2012-01-01

To explore the potential of the swinepox virus (SPV) as vector for Streptococcus suis vaccines, a vector system was developed for the construction of a recombinant SPV carrying bacterial genes. Using this system, a recombinant virus expressing truncated muramidase-released protein (MRP) of S. suis type 2 (SS2), designated rSPV-MRP, was produced and identified by PCR, western blotting and immunofluorescence assays. The rSPV-MRP was found to be only slightly attenuated in PK-15 cells, when compared with the wild-type virus. After immunization intramuscularly with rSPV-MRP, SS2 inactive vaccine (positive control), wild-type SPV (negative control) and PBS (blank control) respectively, all CD1 mice were challenged with a lethal dose or a sublethal dose of SS2 highly virulent strain ZY05719. While SS2 inactive vaccine protected all mice, immunization with rSPV-MRP resulted in 60% survival and protected mice against a lethal dose of the highly virulent SS2 strain, compared with the negative control (P < 0.05). Our data indicate that animals immunized with rSPV-MRP had a significantly reduced bacterial burden in all organs examined, compared to negative controls and blank controls (P <0.05). Antibody titers of the rSPV-MRP-vaccinated group were significantly higher (P <0.001), when compared to negative controls and blank controls. Antibody titers were also significantly higher in the vaccinated group at all time points post-vaccination (P <0.001), compared with the positive controls. These initial results demonstrated that the rSPV-MRP provided mice with protection from systemic SS2 infection. If SPV recombinants have the potential as S. suis vaccines for the use in pigs has to be evaluated in further studies.

Seismic Characterization of a Gas Hydrate Chimney Associated with Acoustic Blanking: Pegasus Basin, New Zealand

NASA Astrophysics Data System (ADS)

Henrys, S. A.; Fraser, D. R. A.; Gorman, A. R.; Pecher, I. A.; Crutchley, G. J.

2016-12-01

The Pegasus Basin on the east coast of New Zealand's North Island in the southern part of the Hikurangi Margin is a frontier petroleum basin that is also expected to contain significant gas hydrate deposits. Extensive faulting in the basin has lead to the development of many interesting and unique focused accumulations of gas hydrates. A 2D seismic dataset acquired in 2009/2010 was reprocessed to examine the gas hydrate systems within the basin. Here, we present one of the more interesting hydrate features in the dataset: a presumed gas chimney within the regional gas hydrate stability zone at the centre of a roughly triangular (in 2D) region of low reflectivity, approximately 8 km wide, that is interpreted to be the result of acoustic blanking. Using automated high density velocity picking, the chimney structure is interpreted to be cored by a 200 m wide low-velocity zone which contains free gas and is flanked by high-velocity bands that are 200-400 m wide. The high-velocity zone is interpreted to correspond to concentrated hydrate deposits within the sedimentary pore spaces. Amplitude vs offset (AVO) and inversion techniques have been applied and the results of this work correspond well to the high-density velocity analyses. The analysis methods all indicate zones of free gas below the Bottom Simulating Reflection (BSR) and within the chimney. Areas of increased hydrate concentrations, including at the base of the gas hydrate stability zone, were also identified. A model for fluid flow and how free gas within the chimney at the centre of the blanking zone is converted to hydrate is discussed. The potential size of the gas hydrate resource present in this feature can be estimated based on the seismic velocities and physical properties determined by inversion.

The EPIC-MOS Particle-Induced Background Spectra

NASA Technical Reports Server (NTRS)

Kuntz, K. D.; Sowden, S. L.

2007-01-01

In order to analyse diffuse emission that fills the field of view, one must accurately characterize the instrumental backgrounds. For the XMM-Newton EPIC instrument these backgrounds include a temporally variable "quiescent" component. as well as the strongly variable soft proton contamination. We have characterized the spectral and spatial response of the EPIC detectors to these background components and have developed tools to remove these backgrounds from observations. The "quiescent" component was characterized using a combination of the filter-wheel-closed data and a database of unexposed-region data. The soft proton contamination was characterized by differencing images and spectra taken during flared and flare-free intervals. After application of our modeled backgrounds, the differences between independent observations of the same region of "blank sky" are consistent with the statistical uncertainties except when there is clear spectral evidence of solar wind charge exchange emission. Using a large sample of blank sky data, we show that strong magnetospheric SWCX emission requires elevated solar wind fluxes; observations through the densest part of the magnetosheath are not necessarily strongly contaminated with SWCX emission.

Introduction of anticoagulation group to polypropylene film by radiation grafting and its blood compatibility

NASA Astrophysics Data System (ADS)

Mao, Chun; Zhang, Can; Qiu, Yongzhi; Zhu, Aiping; Shen, Jian; Lin, Sicong

2004-04-01

Based on in vitro tests for an improvement of the blood compatibility of polypropylene (PP) films by grafting O-butyrylchitosan (OBCS), we prepared a novel biocompatible film. The immobilization was accomplished by irradiating with ultraviolet light, OBCS being coated on the film surface to photolyze azide groups, thus cross-linking OBCS and PP together. The grafted sample films were verified by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), electron spectroscopy for chemical analysis (ESCA) and the water contact angle measurements. The blood compatibility of the OBCS-grafted PP films was evaluated by platelet rich plasma (PRP) contacting experiments and protein adsorption experiments using blank PP film as the control. It demonstrated that blood compatibility of the OBCS-grafted surfaces is better than that of the blank PP. The suitable modifications could be carried out to tailor PP biomaterial to meet the specific needs of different biomedical applications. These results suggest that the photocrosslinkable chitosan developed here has the potential of serving as a new biomaterial in medical use.

Delineating the Construct Network of the Personnel Reaction Blank: Associations with Externalizing Tendencies and Normal Personality

PubMed Central

Blonigen, Daniel M.; Patrick, Christopher J.; Gasperi, Marianna; Steffen, Benjamin; Ones, Deniz S.; Arvey, Richard D.; de Oliveira Baumgartl, Viviane; do Nascimento, Elizabeth

2010-01-01

Integrity testing has long been utilized in personnel selection to screen for tendencies toward counterproductive workplace behaviors. The construct of externalizing from the psychopathology literature represents a coherent spectrum marked by disinhibitory traits and behaviors. The present study used a sample of male and female undergraduates to examine the construct network of the Personnel Reaction Blank (PRB; Gough, Arvey, & Bradley, 2004), a measure of integrity, in relation to externalizing as well as normal-range personality constructs assessed by the Multidimensional Personality Questionnaire (MPQ; Tellegen & Waller, 2008). Results revealed moderate to strong associations between several PRB scales and externalizing, which were largely accounted for by MPQ traits subsumed by Negative Emotionality and Constraint. After accounting for MPQ traits in the prediction of externalizing, a modest predictive increment was achieved when adding the PRB scales, particularly biographical indicators from the Prosocial Background subscale. The findings highlight externalizing as a focal criterion for scale development in the integrity testing literature, and help delineate the construct network of the PRB within the domains of personality and psychopathology. PMID:21171783

Multiphysics Object Oriented Simulation Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

The Multiphysics Object Oriented Simulation Environment (MOOSE) software library developed at Idaho National Laboratory is a tool. MOOSE, like other tools, doesn't actually complete a task. Instead, MOOSE seeks to reduce the effort required to create engineering simulation applications. MOOSE itself is a software library: a blank canvas upon which you write equations and then MOOSE can help you solve them. MOOSE is comparable to a spreadsheet application. A spreadsheet, by itself, doesn't do anything. Only once equations are entered into it will a spreadsheet application compute anything. Such is the same for MOOSE. An engineer or scientist can utilizemore » the equation solvers within MOOSE to solve equations related to their area of study. For instance, a geomechanical scientist can input equations related to water flow in underground reservoirs and MOOSE can solve those equations to give the scientist an idea of how water could move over time. An engineer might input equations related to the forces in steel beams in order to understand the load bearing capacity of a bridge. Because MOOSE is a blank canvas it can be useful in many scientific and engineering pursuits.« less

Research, Development, Training, and Evaluation (RDTE) Support Delivery Order 1: Computational Cognitive Models

DTIC Science & Technology

1993-09-01

AL/HR-TR- 1993-0072 AD-A271 837 RESEARCH, DEVELOPMENT, TRAINING, AND A EVALUATION (RDTE) SUPPORT R DELIVERY ORDER 1 : COMPUTATIONAL COGNITIVE M MODELS...Stephen E. Deutsch :-"LEC"E R Eva Hudlicka eNOV04 1 0 Marilyn J. Adams0 Carl E. FeehrerN G BOLT BERANEK AND NEWMAN, INCG10 MOULTON STREET CAMBRIDGE...Washington. DC 20503 1 . AGENCY USE ONLY (Leave blank) 2 REPORT DATE 3. REPORT TYPE AND DATES COVERED Sep 1993 Final - March 1992 to April 1993 4

Functionalization of chitosan by a free radical reaction: Characterization, antioxidant and antibacterial potential.

PubMed

Moreno-Vásquez, María Jesús; Valenzuela-Buitimea, Emma Lucía; Plascencia-Jatomea, Maribel; Encinas-Encinas, José Carmelo; Rodríguez-Félix, Francisco; Sánchez-Valdes, Saúl; Rosas-Burgos, Ema Carina; Ocaño-Higuera, Víctor Manuel; Graciano-Verdugo, Abril Zoraida

2017-01-02

Chitosan was functionalized with epigallocatechin gallate (EGCG) by a free radical-induced grafting procedure, which was carried out by a redox pair (ascorbic acid/hydrogen peroxide) as the radical initiator. The successful preparation of EGCG grafted-chitosan was verified by spectroscopic (UV, FTIR and XPS) and thermal (DSC and TGA) analyses. The degree of grafting of phenolic compounds onto the chitosan was determined by the Folin-Ciocalteu procedure. Additionally, the biological activities (antioxidant and antibacterial) of pure EGCG, blank chitosan and EGCG grafted-chitosan were evaluated. The spectroscopic and thermal results indicate chitosan functionalization with EGCG; the EGCG content was 25.8mg/g of EGCG grafted-chitosan. The antibacterial activity of the EGCG grafted-chitosan was increased compared to pure EGCG or blank chitosan against S. aureus and Pseudomonas sp. (p<0.05). Additionally, EGCG grafted-chitosan showed higher antioxidant activity than blank chitosan. These results indicate that EGCG grafted-chitosan might be useful in active food packaging. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biogeography of key mesozooplankton species in the North Atlantic, by manual counting methods, and egg production of Calanus finmarchicus

NASA Astrophysics Data System (ADS)

Melle, W.; Runge, J. A.; Head, E.; Plourde, S.; Castellani, C.; Licandro, P.; Pierson, J.; Jonasdottir, S. H.; Johnson, C.; Broms, C.; Debes, H.; Falkenhaug, T.; Gaard, E.; Gislason, A.; Heath, M. R.; Niehoff, B.; Nielsen, T. G.; Pepin, P.; Stenevik, E. K.; Chust, G.

2014-04-01

Here we present a new, pan-Atlantic compilation of data on key mesozooplankton species, including the possibly most important copepod, Calanus finmarchicus. Distributional data of ten representative zooplankton taxa, from recent (2000-2009) Continuous Plankton Recorder data, are presented, along with basin-scale data of the phytoplankton colour index. Then we present a compilation of data on C. finmarchicus including observations of abundance, demography, egg production and female size with accompanying data on temperature and chlorophyll. This is a contribution by Canadian, European and US scientists and their institutions. http://doi.pangaea.de/10.1594/PANGAEA.820732, http://doi.pangaea.de/10.1594/PANGAEA.824423, http://doi.pangaea.de/10.1594/PANGAEA.828393.

Combining the pressure effect with local heat treatment for improving the sheet metal forming process

NASA Astrophysics Data System (ADS)

Palumbo, G.; Piccininni, A.; Guglielmi, P.; Sorgente, D.; Tricarico, L.

2016-08-01

The present work deals with the advantages in the Hydromechanical Deep Drawing (HDD) when AA5754 Tailored Heat Treated Blanks (THTBs) are adopted. It is well known that the creation of a suitable distribution of material properties increases the process performance. When non heat-treatable alloys are considered, the THTB approach can be successfully applied to increase the Limit Drawing Ratio (LDR) by changing the peripheral zone into the annealed state starting from a cold-worked blank. If this approach is combined with the advantages of a counterpressure, even more remarkable improvements can be achieved. Due to the large number of involved parameters, the optimized design of both the local treatment and the pressure profile were investigated coupling an axial symmetric Finite Element model with the integration platform modeFRONTIER. Results confirmed the possibility of increasing the LDR from 2.0 (Deep Drawing using a blank in the annealed state) up to about 3.0 if combining the adoption of a THTB with the optimal pressure profile.

Influence of Mycotoxins and a Mycotoxin Adsorbing Agent on the Oral Bioavailability of Commonly Used Antibiotics in Pigs

PubMed Central

Goossens, Joline; Vandenbroucke, Virginie; Pasmans, Frank; De Baere, Siegrid; Devreese, Mathias; Osselaere, Ann; Verbrugghe, Elin; Haesebrouck, Freddy; De Saeger, Sarah; Eeckhout, Mia; Audenaert, Kris; Haesaert, Geert; De Backer, Patrick; Croubels, Siska

2012-01-01

It is recognized that mycotoxins can cause a variety of adverse health effects in animals, including altered gastrointestinal barrier function. It is the aim of the present study to determine whether mycotoxin-contaminated diets can alter the oral bioavailability of the antibiotics doxycycline and paromomycin in pigs, and whether a mycotoxin adsorbing agent included into diets interacts with those antibiotics. Experiments were conducted with pigs utilizing diets that contained blank feed, mycotoxin-contaminated feed (T-2 toxin or deoxynivalenol), mycotoxin-contaminated feed supplemented with a glucomannan mycotoxin binder, or blank feed supplemented with mycotoxin binder. Diets with T-2 toxin and binder or deoxynivalenol and binder induced increased plasma concentrations of doxycycline administered as single bolus in pigs compared to diets containing blank feed. These results suggest that complex interactions may occur between mycotoxins, mycotoxin binders, and antibiotics which could alter antibiotic bioavailability. This could have consequences for animal toxicity, withdrawal time for oral antibiotics, or public health. PMID:22606377

Detection of Organic Constituents Including Chloromethylpropene in the Analyses of the ROCKNEST Drift by Sample Analysis at Mars (SAM)

NASA Technical Reports Server (NTRS)

Eigenbrode, J. L.; Glavin, D.; Coll, P.; Summons, R. E.; Mahaffy, P.; Archer, D.; Brunner, A.; Conrad, P.; Freissinet, C.; Martin, M.;

Ground-water sampling methods and quality-control data for the Red River of the North basin, Minnesota, North Dakota, and South Dakota, 1993-95

USGS Publications Warehouse

Menheer, M.A.; Brigham, M.E.

1997-01-01

Quality-control data demonstrated that most constituents measured for this study yielded reproducible data, with low to undetectable contamination from the sampling and analytical procedures. Several constituents were occasionally or frequently detected in blank samples at levels similar to low-concentration ground-water-quality samples. For example, iron was detected in 75 percent of the blank samples, with a maximum concentration of 27 [ig/L, indicating that iron contamination may interfere with its determination at low levels in ground waters. Copper, aluminum, and dissolved organic carbon concentrations in blank samples overlap those determined in ground-waterquality samples, thereby precluding quantitative reporting of those constituents. Most pesticide data are reproducible, with minimal bias. Some pesticides had low but consistent recoveries; these data may be useful if spike and surrogate data are carefully considered. Data for some pesticides measured in this study should not be quantitatively reported or used, because they may underestimate the concentrations of those pesticides in ground waters.

[Effect of low-energy 633 nm red light stimulation on proliferation and reactive oxygen species level of human epidermal cell line HaCaT].

PubMed

Chen, Z Y; Li, D L; Duan, X D; Peng, D Z

2016-09-20

To investigate the changes of proliferative activity and reactive oxygen species level of human epidermal cell line HaCaT after being irradiated with low-energy 633 nm red light. Irradiation distance was determined through preliminary experiment. HaCaT cells were conventionally sub-cultured with RPMI 1640 culture medium containing 10% fetal calf serum, 100 U/mL penicillin, and 100 μg/mL streptomycin. Cells of the third passage were used in the following experiments. (1) Cells were divided into blank control group and 0.082, 0.164, 0.245, 0.491, 1.472, 2.453, 4.910, and 9.810 J/cm(2) irradiation groups according to the random number table, with 3 wells in each group. Cells in blank control group were not irradiated, while cells in the latter 8 irradiation groups were irradiated with 633 nm red light for 10, 20, 30, 60, 180, 300, 600, and 1 200 s in turn. Cells were reirradiated once every 8 hours. After being irradiated for 48 hours (6 times) in irradiation groups, the proliferative activity of cells in 9 groups was determined with cell counting kit 8 and microplate reader (denoted as absorbance value). (2) Another batch of cells were grouped and irradiated as in experiment (1). After being irradiated for once in irradiation groups, cells in 9 groups were conventionally cultured for 60 min with detection reagent of reactive oxygen species. At post culture minute (PCM) 0 (immediately), 30, 60, and 120, reactive oxygen species level of cells was determined with microplate reader (denoted as absorbance value). (3) Another batch of cells were divided into blank control group, 0.082, 0.491, 2.453, and 9.810 J/cm(2) irradiation groups, and positive control group. Cells in blank control group and positive control group were not irradiated (positive control reagent of reactive oxygen species was added to cells in positive control group), and cells in irradiation groups were irradiated as in experiment (1) for once. The expression of reactive oxygen species in cells of each group was observed by confocal laser scanning microscope. Data were processed with one-way analysis of variance, analysis of variance for repeated measurement, and t test. (1) Irradiation distance was 10 cm. Proliferative activity of cells in blank control group and 0.082, 0.164, 0.245, 0.491, 1.472, 2.453, 4.910, and 9.810 J/cm(2) irradiation groups was 1.000, 1.116±0.031, 1.146±0.016, 1.162±0.041, 1.179±0.016, 1.207±0.016, 1.247±0.040, 1.097±0.059, and 0.951±0.118, respectively. Compared with that in blank control group, proliferative activity of cells in 0.082-2.453 J/cm(2) irradiation groups was significantly higher (with t values from -22.803 to -6.779, P values below 0.05). Proliferative activity of cells in 4.910 and 9.810 J/cm(2) irradiation groups was similar to that in blank control group (with t values respectively -2.854 and 0.711, P values above 0.05). (2) Compared with that in blank control group, reactive oxygen species level of cells was significantly enhanced at PCM 0 and 30 in 0.164-2.453 J/cm(2) irradiation groups (with t values from -12.453 to -4.684, P<0.05 or P<0.01), while that showed no significant change in 0.082, 4.910, and 9.810 J/cm(2) irradiation groups (with t values from -3.925 to -0.672, P values above 0.05). Compared with that in blank control group, reactive oxygen species level of cells was significantly enhanced at PCM 60 in 0.082-2.453 J/cm(2) irradiation groups (with t values from -11.387 to -4.717, P<0.05 or P<0.01). Compared with that in blank control group, reactive oxygen species level of cells was significantly enhanced at PCM 120 in 0.491-2.453 J/cm(2) irradiation groups (with t values from -10.657 to -6.644, P<0.05 or P<0.01). (3) Compared with that in blank control group, the expression of reactive oxygen species of cells was increased in 0.082, 0.491, and 2.453 J/cm(2) irradiation groups and positive control group. The expression of reactive oxygen species of cells in 9.810 J/cm(2) irradiation group was attenuated when compared with the expressions in the other irradiation groups. Reactive oxygen species expressed in mitochondria of cells in each group. Low-energy 633 nm red light can enhance the proliferation of human epidermal cell line HaCaT, and the effect is closely related to the increase of reactive oxygen species produced by mitochondria after being stimulated by red light irradiation.

Determination of low-level (sub-microgram) sulfur concentrations by isotope dilution multi-collector inductively couple plasma mass spectrometry using a 33S spike and internal normalization for mass bias correction.

PubMed

Mann, Jacqueline L; Vocke, Robert D; Kelly, W Robert

2012-05-30

The certification of sulfur (S) in Standard Reference Materials™ by the National Institute of Standards and Technology (NIST) has been exclusively performed using isotope dilution thermal ionization mass spectrometry (ID-TIMS). The ID-TIMS measurement method is limited in its capability for low concentration measurements (<1 µg/g) due to the blank associated with the chemical reduction procedure (≈0.2 S µg). Newly developed materials and applications, such as biofuels made from soy and nanomedicine, pose a challenge to the ID-TIMS technique because of their very low concentrations (<1 µg/g) of S. As described here, a measurement technique with low S blanks is essential for low-level S measurements. An isotope dilution (ID) multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) method combined with an internal normalization approach for mass bias correction has been used to determine low-level S concentrations in synthetically prepared mixtures using a (33)S-enriched spike material. Dilute sulfur solutions (1 µg S/g) were prepared from NIST SRM 3154 (Sulfate Spectrometric Solution) to test the capability of this technique for measuring very low-level S concentrations. The concentration results for each solution were 0.983 ± 0.004 µg/g (95% CI, n = 2, k = 2), 1.006 ± 0.005 µg/g (95% CI, n = 2, k = 2), and 0.999 ± 0.003 µg/g (95% CI, n = 2, k = 2), in excellent agreement with the gravimetric determination, deviating less than 0.35% and suggesting the technique can yield unbiased and accurate results. The blanks averaged 13 ± 0.0017 ng S (1s). The data results provide a clear indication that the ID-MC-ICP-MS method for the determination of low-level S concentrations is feasible. The more than one order of magnitude reduction of the blanks suggests that it is a better alternative to the ID-TIMS method for very low S materials such as are encountered in biofuels and some biochemical species. Published 2012. This article is a US Government work and is in the public domain in the USA. Published 2012. This article is a US Government work and is in the public domain in the USA.

Process optimization for particle removal on blank chrome mask plates in preparation for resist application

NASA Astrophysics Data System (ADS)

Osborne, Stephen; Smith, Eryn; Woster, Eric; Pelayo, Anthony

2002-03-01

As integrated circuits require smaller lines to provide the memory and processing capability for tomorrow's marketplace, the photomask industry is adopting higher contrast resists to improve photomask lithography. Photomask yield for several high-contrast resist recipes may be improved by coating masks at the mask shop. When coating at a mask shop, an effective method is available that uses coat/bake cluster tools to ensure blanks are clean prior to coating. Many high-contrast resists are available, and some are more susceptible to time-dependent performance factors than conventional resists. One of these factors is the time between coating and writing. Although future methods may reduce the impact of this factor, one current trend is to reduce this time by coating plates at the mask shop just prior to writing. Establishing an effective process to clean blanks prior to coating is necessary for product quality control and is a new task that is critical for maskmakers who previously purchased mask plates but have decided to begin coating them within their facility. This paper provides a strategy and method to be used within coat/bake cluster tools to remove particle contamination from mask blanks. The process uses excimer-UV ionizing radiation and ozone to remove organic contaminants, and then uses a wet process combined with megasonic agitation, surfactant, and spin forces. Megasonic agitation with surfactant lifts up particles, while the convective outflow of water enhances centripetal shear without accumulating harmful charge.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

NASA Astrophysics Data System (ADS)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-04-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

NASA Astrophysics Data System (ADS)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-06-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

Development of a Spherical Combustion Chamber for Measuring Laminar Flame Speeds in Navy Bulk Fuels and Biofuel Blends

DTIC Science & Technology

2011-12-01

determine laminar flame speeds using the spherical flame method. An experimental combustion chamber, based on the constant-volume bomb method, was...INTENTIONALLY LEFT BLANK v ABSTRACT This thesis presents the results of an experimental study to determine laminar flame speeds using the spherical...for ethane/air flames at various pressures reproduced from [6]....................8 Figure 4. Experimentally determined laminar flame speed as a

La Palabra es Nuestra: Primaria para Adultos. Segunda Parte, Volumen 1-2. Edicion Experimental (The Language Is Ours: Primer for Adults. Part Two, Volumes 1-2. Experimental Edition).

ERIC Educational Resources Information Center

Instituto Nacional para la Educacion de los Adultos, Mexico City (Mexico).

These workbooks are part of a Mexican series of instructional materials designed for Spanish speaking adults who are in the process becoming literate or have recently become literate in their native language. They provide readings and exercises for developing literacy skills. Pictures and fill-in-the blank exercises appear frequently. Volume 1…

Use of Statechart Assertions for Modeling Human-in-the-Loop Security Analysis and Decision-Making Processes

DTIC Science & Technology

2012-06-01

THIS PAGE INTENTIONALLY LEFT BLANK xv LIST OF ACRONYMS AND ABBREVIATIONS BPM Business Process Model BPMN Business Process Modeling Notation C&A...checking leads to an improvement in the quality and success of enterprise software development. Business Process Modeling Notation ( BPMN ) is an...emerging standard that allows business processes to be captured in a standardized format. BPMN lacks formal semantics which leaves many of its features

Low-Power Fault Tolerance for Spacecraft FPGA-Based Numerical Computing

DTIC Science & Technology

2006-09-01

Ranganathan , “Power Management – Guest Lecture for CS4135, NPS,” Naval Postgraduate School, Nov 2004 [32] R. L. Phelps, “Operational Experiences with the...4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2...undesirable, are not necessarily harmful. Our intent is to prevent errors by properly managing faults. This research focuses on developing fault-tolerant

Computing the Algebraic Immunity of Boolean Functions on the SRC-6 Reconfigurable Computer

DTIC Science & Technology

2012-03-01

and Budget, Paperwork Reduction Project (0704-0188) Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2 . REPORT DATE March 2012 3. REPORT... CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME(S) AND ADDRESS(ES) N/A 10. SPONSORING...developed for this conversion. This reduced form requires many fewer gates and has ( )n delay versus ( 2 ) n delay for a full transeunt triangle

[How dangerous are "mouse trap projectile traps"?].

PubMed

Schyma, C; Placidi, P

1994-01-01

The authors research by experiments to define the potency of wounding of a special mouse trap which belongs to the spring-guns. Besides the regular assigned 9 mm blank cartridge also the 9 x 17 mm "green" cattle stunning cartridge is tested. Shots were made on soap, cotton and skin on different conditions. As result the authors found that by close range shots (up to 1 cm) by the blank cartridge badly healing wounds are caused. The 600 Joule cattle stunning cartridge is able to mutilate the hand by contact shots.

Non-Tactical Vehicle Replacement for the Department of the Navy’s Medium- and Heavy-Duty Vehicle Fleet

DTIC Science & Technology

2016-12-01

Form Approved OMB No. 0704–0188 Public reporting burden for this collection of information is estimated to average 1 hour per response, including the...ABSTRACT UU NSN 7540–01-280-5500 Standard Form 298 (Rev. 2–89) Prescribed by ANSI Std. 239–18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii...BLANK 1 I. INTRODUCTION The sooner we get started with alternative energy sources and recognize that fossil fuels makes us less secure as a nation

a New Initiative for Tiling, Stitching and Processing Geospatial Big Data in Distributed Computing Environments

NASA Astrophysics Data System (ADS)

Olasz, A.; Nguyen Thai, B.; Kristóf, D.

2016-06-01

Within recent years, several new approaches and solutions for Big Data processing have been developed. The Geospatial world is still facing the lack of well-established distributed processing solutions tailored to the amount and heterogeneity of geodata, especially when fast data processing is a must. The goal of such systems is to improve processing time by distributing data transparently across processing (and/or storage) nodes. These types of methodology are based on the concept of divide and conquer. Nevertheless, in the context of geospatial processing, most of the distributed computing frameworks have important limitations regarding both data distribution and data partitioning methods. Moreover, flexibility and expendability for handling various data types (often in binary formats) are also strongly required. This paper presents a concept for tiling, stitching and processing of big geospatial data. The system is based on the IQLib concept (https://github.com/posseidon/IQLib/) developed in the frame of the IQmulus EU FP7 research and development project (http://www.iqmulus.eu). The data distribution framework has no limitations on programming language environment and can execute scripts (and workflows) written in different development frameworks (e.g. Python, R or C#). It is capable of processing raster, vector and point cloud data. The above-mentioned prototype is presented through a case study dealing with country-wide processing of raster imagery. Further investigations on algorithmic and implementation details are in focus for the near future.

Quality-assurance data for routine water quality analyses by the U. S. Geological Survey laboratory in Troy, New York; July 1993 through June 1995

USGS Publications Warehouse

Lincoln, Tricia A.; Horan-Ross, Debra A.; McHale, Michael R.; Lawrence, Gregory B.

2001-01-01

A laboratory for analysis of low-ionic strength water has been developed at the U.S. Geological Survey (USGS) office in Troy, N.Y., to analyze samples collected by USGS projects in the Northeast. The laboratory's quality-assurance program is based on internal and interlaboratory quality-assurance samples and quality-control procedures developed to ensure proper sample collection, processing, and analysis. The quality-assurance/quality-control data are stored in the laboratory's SAS data-management system, which provides efficient review, compilation, and plotting of quality-assurance/quality-control data. This report presents and discusses samples analyzed from July 1993 through June 1995. Quality-control results for 18 analytical procedures were evaluated for bias and precision. Control charts show that data from seven of the analytical procedures were biased throughout the analysis period for either high-concentration or low-concentration samples but were within control limits; these procedures were: acid-neutralizing capacity, dissolved inorganic carbon, dissolved organic carbon (soil expulsions), chloride, magnesium, nitrate (colorimetric method), and pH. Three of the analytical procedures were occasionally biased but were within control limits; they were: calcium (high for high-concentration samples for May 1995), dissolved organic carbon (high for highconcentration samples from January through September 1994), and fluoride (high in samples for April and June 1994). No quality-control sample has been developed for the organic monomeric aluminum procedure. Results from the filter-blank and analytical-blank analyses indicate that all analytical procedures in which blanks were run were within control limits, although values for a few blanks were outside the control limits. Blanks were not analyzed for acid-neutralizing capacity, dissolved inorganic carbon, fluoride, nitrate (colorimetric method), or pH. Sampling and analysis precision are evaluated herein in terms of the coefficient of variation obtained for triplicate samples in 14 of the 18 procedures. Data-quality objectives were met by more than 90 percent of the samples analyzed in all procedures except total monomeric aluminum (85 percent of samples met objectives), total aluminum (70 percent of samples met objectives), and dissolved organic carbon (85 percent of samples met objectives). Triplicate samples were not analyzed for ammonium, fluoride, dissolved inorganic carbon, or nitrate (colorimetric method). Results of the USGS interlaboratory Standard Reference Sample Program indicated high data quality with a median result of 3.6 of a possible 4.0. Environment Canada's LRTAP interlaboratory study results indicated that more than 85 percent of the samples met data-quality objectives in 6 of the 12 analyses; exceptions were calcium, dissolved organic carbon, chloride, pH, potassium, and sodium. Data-quality objectives were not met for calcium samples in one LRTAP study, but 94 percent of samples analyzed were within control limits for the remaining studies. Data-quality objectives were not met by 35 percent of samples analyzed for dissolved organic carbon, but 94 percent of sample values were within 20 percent of the most probable value. Data-quality objectives were not met for 30 percent of samples analyzed for chloride, but 90 percent of sample values were within 20 percent of the most probable value. Measurements of samples with a pH above 6.0 were biased high in 54 percent of the samples, although 85 percent of the samples met data-quality objectives for pH measurements below 6.0. Data-quality objectives for potassium and sodium were not met in one study (only 33 percent of the samples analyzed met the objectives), although 85 percent of the sample values were within control limits for the other studies. Measured sodium values were above the upper control limit in all studies. Results from blind reference-sample analyses indicated that data

Validation of a standardized extraction method for formalin-fixed paraffin-embedded tissue samples.

PubMed

Lagheden, Camilla; Eklund, Carina; Kleppe, Sara Nordqvist; Unger, Elizabeth R; Dillner, Joakim; Sundström, Karin

2016-07-01

Formalin-fixed paraffin-embedded (FFPE) samples can be DNA-extracted and used for human papillomavirus (HPV) genotyping. The xylene-based gold standard for extracting FFPE samples is laborious, suboptimal and involves health hazards for the personnel involved. To compare extraction with the standard xylene method to a xylene-free method used in an HPV LabNet Global Reference Laboratory at the Centers for Disease Control (CDC); based on a commercial method with an extra heating step. Fifty FFPE samples were randomly selected from a national audit of all cervical cancer cases diagnosed in Sweden during 10 years. For each case-block, a blank-block was sectioned, as a control for contamination. For xylene extraction, the standard WHO Laboratory Manual protocol was used. For the CDC method, the manufacturers' protocol was followed except for an extra heating step, 120°C for 20min. Samples were extracted and tested in parallel with β-globin real-time PCR, HPV16 real-time PCR and HPV typing using modified general primers (MGP)-PCR and Luminex assays. For a valid result the blank-block had to be betaglobin-negative in all tests and the case-block positive for beta-globin. Overall, detection was improved with the heating method and the amount of HPV-positive samples increased from 70% to 86% (p=0.039). For all samples where HPV type concordance could be evaluated, there was 100% type concordance. A xylene-free and robust extraction method for HPV-DNA typing in FFPE material is currently in great demand. Our proposed standardized protocol appears to be generally useful. Copyright © 2016. Published by Elsevier B.V.

High speed pulsed laser cutting of LiCoO2 Li-ion battery electrodes

NASA Astrophysics Data System (ADS)

Lutey, Adrian H. A.; Fortunato, Alessandro; Carmignato, Simone; Fiorini, Maurizio

2017-09-01

Laser cutting of Li-ion battery electrodes represents an alternative to mechanical blanking that avoids complications associated with tool wear and allows assembly of different cell geometries with a single device. In this study, laser cutting of LiCoO2 Li-ion battery electrodes is performed at up to 5m /s with a 1064nm wavelength nanosecond pulsed fiber laser with a maximum average power of 500W and a repetition rate of up to 2MHz . Minimum average cutting power for cathode and anode multi-layer films is established for 12 parameter groups with velocities over the range 1 - 5m /s , varying laser pulse fluence and overlap. Within the tested parameter range, minimum energy per unit cut length is found to decrease with increasing repetition rate and velocity. SEM analysis of the resulting cut edges reveals visible clearance widths in the range 20 - 50 μm , with cut quality found to improve with velocity due to a reduction in lateral heat conduction losses. Raman line map spectra reveal changes in the cathode at 60 μm from the cut edge, where bands at 486cm-1 and 595cm-1 , corresponding to the Eg and A1g modes of LiCoO2 , are replaced with a single wide band centered at 544cm-1 , and evidence of carbon black is no longer present. No changes in Raman spectra are observed in the anode. The obtained results suggest that further improvements in cutting efficiency and quality could be achieved by increasing the repetition rate above 2MHz , thereby improving ablation efficiency of the metallic conductor layers. The laser source utilized in the present study nonetheless represents an immediately available solution for repeatability and throughput that are superior to mechanical blanking.

Stress polishing of thin shells for adaptive secondary mirrors. Application to the Very Large Telescope deformable secondary

NASA Astrophysics Data System (ADS)

Hugot, E.; Ferrari, M.; Riccardi, A.; Xompero, M.; Lemaître, G. R.; Arsenault, R.; Hubin, N.

2011-03-01

Context. Adaptive secondary mirrors (ASM) are, or will be, key components on all modern telescopes, providing improved seeing conditions or diffraction limited images, thanks to the high-order atmospheric turbulence correction obtained by controlling the shape of a thin mirror. Their development is a key milestone towards future extremely large telescopes (ELT) where this technology is mandatory for successful observations. Aims: The key point of actual adaptive secondaries technology is the thin glass mirror that acts as a deformable membrane, often aspheric. On 6 m - 8 m class telescopes, these are typically 1 m-class with a 2 mm thickness. The optical quality of this shell must be sufficiently good not to degrade the correction, meaning that high spatial frequency errors must be avoided. The innovative method presented here aims at generating aspherical shapes by elastic bending to reach high optical qualities. Methods: This method is called stress polishing and allows generating aspherical optics of a large amplitude with a simple spherical polishing with a full sized lap applied on a warped blank. The main advantage of this technique is the smooth optical quality obtained, free of high spatial frequency ripples as they are classically caused by subaperture toolmarks. After describing the manufacturing process we developed, our analytical calculations lead to a preliminary definition of the geometry of the blank, which allows a precise bending of the substrate. The finite element analysis (FEA) can be performed to refine this geometry by using an iterative method with a criterion based on the power spectral density of the displacement map of the optical surface. Results: Considering the specific case of the Very Large Telescope (VLT) deformable secondary mirror (DSM), extensive FEA were performed for the optimisation of the geometry. Results are showing that the warping will not introduce surface errors higher than 0.3 nm rms on the minimal spatial scale considered on the mirror. Simulations of the flattening operation of the shell also demonstrate that the actuators system is able to correct manufacturing surface errors coming from the warping of the blank with a residual error lower than 8 nm rms.

Evaluation of quality-control data collected by the U.S. Geological Survey for routine water-quality activities at the Idaho National Laboratory and vicinity, southeastern Idaho, 2002-08

USGS Publications Warehouse

Rattray, Gordon W.

2014-01-01

Quality-control (QC) samples were collected from 2002 through 2008 by the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, to ensure data robustness by documenting the variability and bias of water-quality data collected at surface-water and groundwater sites at and near the Idaho National Laboratory. QC samples consisted of 139 replicates and 22 blanks (approximately 11 percent of the number of environmental samples collected). Measurements from replicates were used to estimate variability (from field and laboratory procedures and sample heterogeneity), as reproducibility and reliability, of water-quality measurements of radiochemical, inorganic, and organic constituents. Measurements from blanks were used to estimate the potential contamination bias of selected radiochemical and inorganic constituents in water-quality samples, with an emphasis on identifying any cross contamination of samples collected with portable sampling equipment. The reproducibility of water-quality measurements was estimated with calculations of normalized absolute difference for radiochemical constituents and relative standard deviation (RSD) for inorganic and organic constituents. The reliability of water-quality measurements was estimated with pooled RSDs for all constituents. Reproducibility was acceptable for all constituents except dissolved aluminum and total organic carbon. Pooled RSDs were equal to or less than 14 percent for all constituents except for total organic carbon, which had pooled RSDs of 70 percent for the low concentration range and 4.4 percent for the high concentration range. Source-solution and equipment blanks were measured for concentrations of tritium, strontium-90, cesium-137, sodium, chloride, sulfate, and dissolved chromium. Field blanks were measured for the concentration of iodide. No detectable concentrations were measured from the blanks except for strontium-90 in one source solution and one equipment blank collected in September and October 2004, respectively. The detectable concentrations of strontium-90 in the blanks probably were from a small source of strontium-90 contamination or large measurement variability, or both. Order statistics and the binomial probability distribution were used to estimate the magnitude and extent of any potential contamination bias of tritium, strontium-90, cesium-137, sodium, chloride, sulfate, dissolved chromium, and iodide in water-quality samples. These statistical methods indicated that, with (1) 87 percent confidence, contamination bias of cesium-137 and sodium in 60 percent of water-quality samples was less than the minimum detectable concentration or reporting level; (2) 92‒94 percent confidence, contamination bias of tritium, strontium-90, chloride, sulfate, and dissolved chromium in 70 percent of water-quality samples was less than the minimum detectable concentration or reporting level; and (3) 75 percent confidence, contamination bias of iodide in 50 percent of water-quality samples was less than the reporting level for iodide. These results support the conclusion that contamination bias of water-quality samples from sample processing, storage, shipping, and analysis was insignificant and that cross-contamination of perched groundwater samples collected with bailers during 2002–08 was insignificant.

Overexpression of long intergenic noncoding RNA LINC00312 inhibits the invasion and migration of thyroid cancer cells by down-regulating microRNA-197-3p.

PubMed

Liu, Kai; Huang, Wen; Yan, Dan-Qing; Luo, Qing; Min, Xiang

2017-08-31

The study evaluated the ability of long intergenic noncoding RNA LINC00312 (LINC00312) to influence the proliferation, invasion, and migration of thyroid cancer (TC) cells by regulating miRNA-197-3p. TC tissues and adjacent normal tissues were collected from 211 TC patients. K1 (papillary TC), SW579 (squamous TC), and 8505C (anaplastic TC) cell lines were assigned into a blank, negative control (NC), LINC00312 overexpression, miR-197-3p inhibitors, and LINC00312 overexpression + miR-197-3p mimics group. The expression of LINC00312, miR-197-3p , and p120 were measured using quantitative real-time PCR (qRT-PCR) and Western blotting. Cell proliferation was assessed via CCK8 assay, cell invasion through the scratch test, and cell migration via Transwell assay. In comparison with adjacent normal tissues, the expression of LINC00312 is down-regulated and the expression of miR-197-3p is up-regulated in TC tissues. The dual luciferase reporter gene assay confirmed that P120 is a target of miR-197-3p The expression of LINC00312 and p120 was higher in the LINC00312 overexpression group than in the blank and NV groups. However, the expression of miR-197-3p was lower in the LINC00312 overexpression group than in the blank and NC groups. The miR-197-3p inhibitors group had a higher expression of miR-197-3p , but a lower expression of p120 than the blank and NC groups. The LINC00312 overexpression and miR-197-3p inhibitor groups had reduced cell proliferation, invasion and migration than the blank and NC groups. These results indicate that a LINC00312 overexpression inhibits the proliferation, invasion, and migration of TC cells and that this can be achieved by down-regulating miR-197-3p . © 2017 The Author(s).

Experimental and numerical research on forging with torsion

NASA Astrophysics Data System (ADS)

Petrov, Mikhail A.; Subich, Vadim N.; Petrov, Pavel A.

2017-10-01

Increasing the efficiency of the technological operations of blank production is closely related to the computer-aided technologies (CAx). On the one hand, the practical result represents reality exactly. On the other hand, the development procedure of new process development demands unrestricted resources, which are limited on the SMEs. The tools of CAx were successfully applied for development of new process of forging with torsion and result analysis as well. It was shown, that the theoretical calculations find the confirmation both in praxis and during numerical simulation. The mostly used constructional materials were under study. The torque angles were stated. The simulated results were evaluated by experimental procedure.

Design and Development of a Single Channel RSNS Direction Finder

DTIC Science & Technology

2009-03-01

CH2 12VDC 2.5A, and CH3 -12VDC 0.2A Cable 19 Pasternek Cable RG-306 Variable Attenuator 1 Telonic Altair Attenuation Model 8140S Demodulator Board...information is estimated to average 1 hour per response, including the time for reviewing instruction, searching existing data sources, gathering and...Reduction Project (0704-0188) Washington DC 20503. 1 . AGENCY USE ONLY (Leave blank) 2. REPORT DATE March 2009 3. REPORT TYPE AND DATES COVERED

Development Of A Numerical Tow Tank With Wave Generation To Supplement Experimental Efforts

DTIC Science & Technology

2017-12-01

vehicles CAD computer aided design CFD computational fluid dynamics FVM finite volume method IO information operations ISR intelligence, surveillance, and...deliver a product that I am truly proud of. xv THIS PAGE INTENTIONALLY LEFT BLANK xvi CHAPTER 1: Introduction 1.1 Importance of Tow Tank Testing Modern...wedge installation. 1 In 2016, NPS student Ensign Ryan Tran adapted an existing vertical plunging wedge wave maker design used at the U.S. Naval

Development of a Laboratory-scale Test Facility to Investigate Armor Solutions against Buried Explosive Threats

DTIC Science & Technology

2009-12-01

Centro de Estudios Superiores Navales Mexican Navy México, DF México 5. Dr. Jose O. Sinibaldi Naval Postgraduate School Monterey, CA. 6. Dr. Robert S. Hixson Naval Postgraduate School Monterey, CA ...EXPERIMENTAL SETUP AND PROCEDURE............................................. 67 A. HIGH-SPEED VISION SYSTEM...Mexican Navy, “Con la Satisfacción del Deber Cumplido.” To all of them, I am sincerely grateful. xviii THIS PAGE INTENTIONALLY LEFT BLANK xix

Analysis of NASA’s Post-Challenger Response and Relationship to the Columbia Accident and Investigation

DTIC Science & Technology

2006-09-01

Washington DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE September 2006 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE...recommendations that developed from this broader investigation. This examination will be used to determine to what extent the Commissions findings...system “partially” reusable by using an expendable, external tank to feed the orbiter’s engines and two strap-on reusable boosters to provide the

Developing Evaluation Measures for the Second Stage Next Generation Engine on Evolved Expendable Launch Vehicles

DTIC Science & Technology

2012-03-01

xii THIS PAGE INTENTIONALLY LEFT BLANK xiii LIST OF ACRONYMS AND ABBREVIATIONS CDR Critical Design Review DCSS Delta Cryogenic Second Stage...seen below in Figure 5, include the Common Booster Core powered by a Pratt and Whitney Rocketdyne RS-68 engine, a Delta Cryogenic Second Stage (DCSS...do have one significant similarity. The Centaur of the Atlas V and Delta IV Cryogenic Second Stage, both use variants of the Pratt and Whitney

Temporally Adjusted Complex Ambiguity Function Mapping Algorithm for Geolocating Radio Frequency Signals

DTIC Science & Technology

2014-12-01

Introduction 1.1 Background In today’s world of high -tech warfare, we have developed the ability to deploy virtually any type of ordnance quickly and... ANSI Std. 239–18 i THIS PAGE INTENTIONALLY LEFT BLANK ii Approved for public release; distribution is unlimited TEMPORALLY ADJUSTED COMPLEX AMBIGUITY...this time due to time constraints and the high computational complexity involved in the current implementation of the Moss algorithm. Full maps, with

Development of a Generic Hull Stiffener Modelling Capability for Trident Modeller

DTIC Science & Technology

2013-09-01

Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is estimated to average 1 hour per...Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 This page intentionally left blank. i Abstract …….. This...if a RefCurve referenced an IGES file containing more than one curve, it was assumed that the curves already formed an ordered, connected path; the

Avoidance of Cigarette Pack Health Warnings among Regular Cigarette Smokers

PubMed Central

Maynard, Olivia M.; Attwood, Angela; O’Brien, Laura; Brooks, Sabrina; Hedge, Craig; Leonards, Ute; Munafò, Marcus R.

2016-01-01

Background Previous research with adults and adolescents indicates that plain cigarette packs increase visual attention to health warnings among non-smokers and non-regular smokers, but not among regular smokers. This may be because regular smokers: 1) are familiar with the health warnings, 2) preferentially attend to branding, or 3) actively avoid health warnings. We sought to distinguish between these explanations using eye-tracking technology. Method A convenience sample of 30 adult dependant smokers were recruited to participate in an eye-tracking study. Participants viewed branded, plain and blank packs of cigarettes with familiar and unfamiliar health warnings. The number of fixations to health warnings and branding on the different pack types were recorded. Results Analysis of variance indicated that regular smokers were biased towards fixating the branding location rather than the health warning location on all three pack types (p < 0.002). This bias was smaller, but still evident, for blank packs, where smokers preferentially attended the blank region over the health warnings. Time-course analysis showed that for branded and plain packs, attention was preferentially directed to the branding location for the entire 10 seconds of the stimulus presentation, while for blank packs this occurred for the last 8 seconds of the stimulus presentation. Familiarity with health warnings had no effect on eye gaze location. Conclusion Smokers actively avoid cigarette pack health warnings, and this remains the case even in the absence of salient branding information. Smokers may have learned to divert their attention away from cigarette pack health warnings. These findings have policy implications for the design of health warning on cigarette packs. PMID:24485554

Cone of Darkness: Finding Blank-sky Positions for Multi-object Wide-field Observations

NASA Astrophysics Data System (ADS)

Lorente, N. P. F.

2014-05-01

We present the Cone of Darkness, an application to automatically configure blank-sky positions for a series of stacked, wide-field observations, such as those carried out by the SAMI instrument on the Anglo-Australian Telescope (AAT). The Sydney-AAO Multi-object Integral field spectrograph (SAMI) uses a plug-plate to mount its 13×61 core imaging fibre bundles (hexabundles) in the optical plane at the telescope's prime focus. To make the most efficient use of each plug-plate, several observing fields are typically stacked to produce a single plate. When choosing blank-sky positions for the observations it is most effective to select these such that one set of 26 holes gives valid sky positions for all fields on the plate. However, when carried out manually this selection process is tedious and includes a significant risk of error. The Cone of Darkness software aims to provide uniform blank-sky position coverage over the field of observation, within the limits set by the distribution of target positions and the chosen input catalogs. This will then facilitate the production of the best representative median sky spectrum for use in sky subtraction. The application, written in C++, is configurable, making it usable for a range of instruments. Given the plate characteristics and the positions of target holes, the software segments the unallocated space on the plate and determines the position which best fits the uniform distribution requirement. This position is checked, for each field, against the selected catalog using a TAP ADQL search. The process is then repeated until the desired number of sky positions is attained.

Rapid Freeform Sheet Metal Forming: Technology Development and System Verification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiridena, Vijitha; Verma, Ravi; Gutowski, Timothy

The objective of this project is to develop a transformational RApid Freeform sheet metal Forming Technology (RAFFT) in an industrial environment, which has the potential to increase manufacturing energy efficiency up to ten times, at a fraction of the cost of conventional technologies. The RAFFT technology is a flexible and energy-efficient process that eliminates the need for having geometry-specific forming dies. The innovation lies in the idea of using the energy resource at the local deformation area which provides greater formability, process control, and process flexibility relative to traditional methods. Double-Sided Incremental Forming (DSIF), the core technology in RAFFT, ismore » a new concept for sheet metal forming. A blank sheet is clamped around its periphery and gradually deformed into a complex 3D freeform part by two strategically aligned stylus-type tools that follow a pre-described toolpath. The two tools, one on each side of the blank, can form a part with sharp features for both concave and convex shapes. Since deformation happens locally, the forming force at any instant is significantly decreased when compared to traditional methods. The key advantages of DSIF are its high process flexibility, high energy-efficiency, low capital investment, and the elimination of the need for massive amounts of die casting and machining. Additionally, the enhanced formability and process flexibility of DSIF can open up design spaces and result in greater weight savings.« less

Parametric analysis of plastic strain and force distribution in single pass metal spinning

NASA Astrophysics Data System (ADS)

Choudhary, Shashank; Tejesh, Chiruvolu Mohan; Regalla, Srinivasa Prakash; Suresh, Kurra

2013-12-01

Metal spinning also known as spin forming is one of the sheet metal working processes by which an axis-symmetric part can be formed from a flat sheet metal blank. Parts are produced by pressing a blunt edged tool or roller on to the blank which in turn is mounted on a rotating mandrel. This paper discusses about the setting up a 3-D finite element simulation of single pass metal spinning in LS-Dyna. Four parameters were considered namely blank thickness, roller nose radius, feed ratio and mandrel speed and the variation in forces and plastic strain were analysed using the full-factorial design of experiments (DOE) method of simulation experiments. For some of these DOE runs, physical experiments on extra deep drawing (EDD) sheet metal were carried out using En31 tool on a lathe machine. Simulation results are able to predict the zone of unsafe thinning in the sheet and high forming forces that are hint to the necessity for less-expensive and semi-automated machine tools to help the household and small scale spinning workers widely prevalent in India.

Mission Analysis Program for Solar Electric Propulsion (MAPSEP). Volume 2: User's manual for earth orbital MAPSEP

NASA Technical Reports Server (NTRS)

1975-01-01

The trajectory simulation mode (SIMSEP) requires the namelist SIMSEP to follow TRAJ. The SIMSEP contains parameters which describe the scope of the simulation, expected dynamic errors, and cumulative statistics from previous SIMSEP runs. Following SIMSEP are a set of GUID namelists, one for each guidance correction maneuver. The GUID describes the strategy, knowledge or estimation uncertainties and cumulative statistics for that particular maneuver. The trajectory display mode (REFSEP) requires only the namelist TRAJ followed by scheduling cards, similar to those used in GODSEP. The fixed field schedule cards define: types of data displayed, span of interest, and frequency of printout. For those users who can vary the amount of blank common storage in their runs, a guideline to estimate the total MAPSEP core requirements is given. Blank common length is related directly to the dimension of the dynamic state (NDIM) used in transition matrix (STM) computation, and, the total augmented (knowledge) state (NAUG). The values of program and blank common must be added to compute the total decimal core for a CDC 6500. Other operating systems must scale these requirements appropriately.

Effect of Andrographis paniculata leaf extract on wound healing in rats.

PubMed

Al-Bayaty, Fouad Hussain; Abdulla, Mahmood Ameen; Abu Hassan, Mohamed Ibrahim; Ali, Hapipah Mohd

2012-01-01

This work was carried out to study the effect of topical application of Andrographis paniculata on the rate of wound enclosure and its histological features. A wound was created in four groups of rat in posterior neck region. Blank placebo was applied topically to the wounds of Group 1. Groups 2 and 3 were dressed with placebo containing 5% and 10% extracts of A. paniculata, respectively. Intrasite gel was applied topically to the wounds of Group 4. Macroscopical examination revealed that the rate of wound healing was significantly accelerated in the wound dressed with A. paniculata extract compared to the blank placebo. The wounds dressed with 10% extract or Intrasite gel healed earlier compared to the wounds dressed with placebo containing 5% A. paniculata extract. Histologically, wounds dressed with A. paniculata extracts showed markedly less scar width and contained large amounts of fibroblast proliferation. More collagen and less angiogenesis with absence of inflammatory cells were seen for wounds dressed with 10% A. paniculata compared to the blank placebo. Conclusion, A. paniculata extracts significantly enhanced rate of wound healing in rats.

A study on using pre-forming blank in single point incremental forming process by finite element analysis

NASA Astrophysics Data System (ADS)

Abass, K. I.

2016-11-01

Single Point Incremental Forming process (SPIF) is a forming technique of sheet material based on layered manufacturing principles. The edges of sheet material are clamped while the forming tool is moved along the tool path. The CNC milling machine is used to manufacturing the product. SPIF involves extensive plastic deformation and the description of the process is more complicated by highly nonlinear boundary conditions, namely contact and frictional effects have been accomplished. However, due to the complex nature of these models, numerical approaches dominated by Finite Element Analysis (FEA) are now in widespread use. The paper presents the data and main results of a study on effect of using preforming blank in SPIF through FEA. The considered SPIF has been studied under certain process conditions referring to the test work piece, tool, etc., applying ANSYS 11. The results show that the simulation model can predict an ideal profile of processing track, the behaviour of contact tool-workpiece, the product accuracy by evaluation its thickness, surface strain and the stress distribution along the deformed blank section during the deformation stages.

Rejection of atrial sensing artifacts by a pacing lead with short tip-to-ring spacing.

PubMed

Nash, A; Fröhlig, G; Taborsky, M; Stammwitz, E; Maru, F; Bouwens, L H M; Celiker, C

2005-01-01

The ability of a new pacing lead design, with a 10 mm tip-to-ring spacing, to facilitate rejection of sensed far field R-waves and myopotentials was evaluated. Measurements were performed in 66 patients. The occurrence of far field R-wave sensing and myopotential sensing was determined by means of the surface ECG and the ECG markers provided by the pacemaker. At an atrial sensitivity of 0.25 mV and an atrial blanking of 50 ms far field R-wave sensing was observed in 12 patients (18.2%) and at an atrial sensitivity of 1.0 mV no far-field R-wave sensing was observed. Myopotentials were sensed in 3 patients. In all patients the measured P-wave amplitude was at least twice the estimated amplitude of the far field R-wave at an atrial blanking of 50 ms. The results from this study show that a small tip-to-ring spacing allows for programming of a high atrial sensitivity and short atrial blanking with an acceptably low risk for atrial artifact sensing.

Gravimetric Analysis of Particulate Matter using Air Samplers Housing Internal Filtration Capsules.

PubMed

O'Connor, Sean; O'Connor, Paula Fey; Feng, H Amy; Ashley, Kevin

2014-10-01

An evaluation was carried out to investigate the suitability of polyvinyl chloride (PVC) internal capsules, housed within air sampling devices, for gravimetric analysis of airborne particles collected in workplaces. Experiments were carried out using blank PVC capsules and PVC capsules spiked with 0,1 - 4 mg of National Institute of Standards and Technology Standard Reference Material ® (NIST SRM) 1648 (Urban Particulate Matter) and Arizona Road Dust (Air Cleaner Test Dust). The capsules were housed within plastic closed-face cassette samplers (CFCs). A method detection limit (MDL) of 0,075 mg per sample was estimated. Precision S r at 0,5 - 4 mg per sample was 0,031 and the estimated bias was 0,058. Weight stability over 28 days was verified for both blanks and spiked capsules. Independent laboratory testing on blanks and field samples verified long-term weight stability as well as sampling and analysis precision and bias estimates. An overall precision estimate Ŝ rt of 0,059 was obtained. An accuracy measure of ±15,5% was found for the gravimetric method using PVC internal capsules.

Flight Test Measurements From The Tu- 144LL Structure/Cabin Noise Experiment

NASA Technical Reports Server (NTRS)

Rizzi, Stephen A.; Rackl, Robert G.; Andrianov, Eduard V.

2000-01-01

During the period September 1997 to February 1998, the Tupolev 144 Supersonic Flyine Laboratory was used to obtain data for the purpose of enlarging the data base used by models for the prediction of cabin noise in supersonic passenger airplanes. Measured were: turbulent boundary layer pressure fluctuations on the fuselage in seven instrumented window blanks distributed over the length of the fuselage; structural response with accelerometers on skin panels close to those window blanks-, interior noise with microphones at the same fuselage bay stations as those window blanks. Flight test points were chosen to cover much of the TU- 144's flight envelope, as well as to obtain as large a unit Reynolds number range as possible at various Mach numbers: takeoff, landing, six subsonic cruise conditions, and eleven supersonic conditions up to Mach 2. Engine runups and reverberation times were measured with a stationary aircraft. The data in the form of time histories of the acoustic signals, together with auxiliary data and basic MATLAB processing modules, are available on CD-R disks.

Design study of the geometry of the blanking tool to predict the burr formation of Zircaloy-4 sheet

NASA Astrophysics Data System (ADS)

Ha, Jisun; Lee, Hyungyil; Kim, Dongchul; Kim, Naksoo

2013-12-01

In this work, we investigated factors that influence burr formation for zircaloy-4 sheet used for spacer grids of nuclear fuel roads. Factors we considered are geometric factors of punch. We changed clearance and velocity in order to consider the failure parameters, and we changed shearing angle and corner radius of L-shaped punch in order to consider geometric factors of punch. First, we carried out blanking test with failure parameter of GTN model using L-shaped punch. The tendency of failure parameters and geometric factors that affect burr formation by analyzing sheared edges is investigated. Consequently, geometric factor's influencing on the burr formation is also high as failure parameters. Then, the sheared edges and burr formation with failure parameters and geometric factors is investigated using FE analysis model. As a result of analyzing sheared edges with the variables, we checked geometric factors more affect burr formation than failure parameters. To check the reliability of the FE model, the blanking force and the sheared edges obtained from experiments are compared with the computations considering heat transfer.

Scale up of large ALON® and spinel windows

NASA Astrophysics Data System (ADS)

Goldman, Lee M.; Kashalikar, Uday; Ramisetty, Mohan; Jha, Santosh; Sastri, Suri

2017-05-01

Aluminum Oxynitride (ALON® Transparent Ceramic) and Magnesia Aluminate Spinel (Spinel) combine broadband transparency with excellent mechanical properties. Their cubic structure means that they are transparent in their polycrystalline form, allowing them to be manufactured by conventional powder processing techniques. Surmet has scaled up its ALON® production capability to produce and deliver windows as large as 4.4 sq ft. We have also produced our first 6 sq ft window. We are in the process of producing 7 sq ft ALON® window blanks for armor applications; and scale up to even larger, high optical quality blanks for Recce window applications is underway. Surmet also produces spinel for customers that require superior transmission at the longer wavelengths in the mid wave infra-red (MWIR). Spinel windows have been limited to smaller sizes than have been achieved with ALON. To date the largest spinel window produced is 11x18-in, and windows 14x20-in size are currently in process. Surmet is now scaling up its spinel processing capability to produce high quality window blanks as large as 19x27-in for sensor applications.

Object form discontinuity facilitates displacement discrimination across saccades.

PubMed

Demeyer, Maarten; De Graef, Peter; Wagemans, Johan; Verfaillie, Karl

2010-06-01

Stimulus displacements coinciding with a saccadic eye movement are poorly detected by human observers. In recent years, converging evidence has shown that this phenomenon does not result from poor transsaccadic retention of presaccadic stimulus position information, but from the visual system's efforts to spatially align presaccadic and postsaccadic perception on the basis of visual landmarks. It is known that this process can be disrupted, and transsaccadic displacement detection performance can be improved, by briefly blanking the stimulus display during and immediately after the saccade. In the present study, we investigated whether this improvement could also follow from a discontinuity in the task-irrelevant form of the displaced stimulus. We observed this to be the case: Subjects more accurately identified the direction of intrasaccadic displacements when the displaced stimulus simultaneously changed form, compared to conditions without a form change. However, larger improvements were still observed under blanking conditions. In a second experiment, we show that facilitation induced by form changes and blanks can combine. We conclude that a strong assumption of visual stability underlies the suppression of transsaccadic change detection performance, the rejection of which generalizes from stimulus form to stimulus position.

Gravimetric Analysis of Particulate Matter using Air Samplers Housing Internal Filtration Capsules

PubMed Central

O'Connor, Sean; O'Connor, Paula Fey; Feng, H. Amy

2015-01-01

Summary An evaluation was carried out to investigate the suitability of polyvinyl chloride (PVC) internal capsules, housed within air sampling devices, for gravimetric analysis of airborne particles collected in workplaces. Experiments were carried out using blank PVC capsules and PVC capsules spiked with 0,1 – 4 mg of National Institute of Standards and Technology Standard Reference Material® (NIST SRM) 1648 (Urban Particulate Matter) and Arizona Road Dust (Air Cleaner Test Dust). The capsules were housed within plastic closed-face cassette samplers (CFCs). A method detection limit (MDL) of 0,075 mg per sample was estimated. Precision Sr at 0,5 - 4 mg per sample was 0,031 and the estimated bias was 0,058. Weight stability over 28 days was verified for both blanks and spiked capsules. Independent laboratory testing on blanks and field samples verified long-term weight stability as well as sampling and analysis precision and bias estimates. An overall precision estimate Ŝrt of 0,059 was obtained. An accuracy measure of ±15,5% was found for the gravimetric method using PVC internal capsules. PMID:26435581

Modulation of radial blood flow during Braille character discrimination task.

PubMed

Murata, Jun; Matsukawa, K; Komine, H; Tsuchimochi, H

2012-03-01

Human hands are excellent in performing sensory and motor function. We have hypothesized that blood flow of the hand is dynamically regulated by sympathetic outflow during concentrated finger perception. To identify this hypothesis, we measured radial blood flow (RBF), radial vascular conductance (RVC), heart rate (HR), and arterial blood pressure (AP) during Braille reading performed under the blind condition in nine healthy subjects. The subjects were instructed to read a flat plate with raised letters (Braille reading) for 30 s by the forefinger, and to touch a blank plate as control for the Braille discrimination procedure. HR and AP slightly increased during Braille reading but remained unchanged during the touching of the blank plate. RBF and RVC were reduced during the Braille character discrimination task (decreased by -46% and -49%, respectively). Furthermore, the changes in RBF and RVC were much greater during the Braille character discrimination task than during the touching of the blank plate (decreased by -20% and -20%, respectively). These results have suggested that the distribution of blood flow to the hand is modulated via sympathetic nerve activity during concentrated finger perception.

On the construction of a 2-metre mirror blank for the universal reflecting telescope in Tautenburg (German Title: Über die Fertigung eines 2-Meter-Spiegelträgers für das Universal-Spiegelteleskop in Tautenburg )

NASA Astrophysics Data System (ADS)

Lödel, Wolfgang

The astronomers' desire to penetrate deeper into space transforms into a demand for larger telescopes. The primary mirror constitutes the main part of a reflecting telescope, and it determines all subsequent activities. Already in the 1930s activities existed in the Schott company to manufacture mirror blanks up to diameters of 2 metres, which could not be pursued because of political constraints. This ambitious goal was again picked up a few years after the war. At a time when the procurement of raw materials was extremely difficult, the glass workers of Schott in Jena attacked this large project. After some failures, a good mirror blank could be delivered to the Carl Zeiss Company in 1951 for further processing and for the construction of the first 2-metre reflecting telescope. From 1960 to 1986, this mirror made from optical glass ZK7 served its purpose at the Karl Schwarzschild Observatory in Tautenburg. lt was then replaced by a zero expansion glass ceramics mirror.

Lessons learned in preparing method 29 filters for compliance testing audits.

PubMed

Martz, R F; McCartney, J E; Bursey, J T; Riley, C E

2000-01-01

Companies conducting compliance testing are required to analyze audit samples at the time they collect and analyze the stack samples if audit samples are available. Eastern Research Group (ERG) provides technical support to the EPA's Emission Measurements Center's Stationary Source Audit Program (SSAP) for developing, preparing, and distributing performance evaluation samples and audit materials. These audit samples are requested via the regulatory Agency and include spiked audit materials for EPA Method 29-Metals Emissions from Stationary Sources, as well as other methods. To provide appropriate audit materials to federal, state, tribal, and local governments, as well as agencies performing environmental activities and conducting emission compliance tests, ERG has recently performed testing of blank filter materials and preparation of spiked filters for EPA Method 29. For sampling stationary sources using an EPA Method 29 sampling train, the use of filters without organic binders containing less than 1.3 microg/in.2 of each of the metals to be measured is required. Risk Assessment testing imposes even stricter requirements for clean filter background levels. Three vendor sources of quartz fiber filters were evaluated for background contamination to ensure that audit samples would be prepared using filters with the lowest metal background levels. A procedure was developed to test new filters, and a cleaning procedure was evaluated to see if a greater level of cleanliness could be achieved using an acid rinse with new filters. Background levels for filters supplied by different vendors and within lots of filters from the same vendor showed a wide variation, confirmed through contact with several analytical laboratories that frequently perform EPA Method 29 analyses. It has been necessary to repeat more than one compliance test because of suspect metals background contamination levels. An acid cleaning step produced improvement in contamination level, but the difference was not significant for most of the Method 29 target metals. As a result of our studies, we conclude: Filters for Method 29 testing should be purchased in lots as large as possible. Testing firms should pre-screen new boxes and/or new lots of filters used for Method 29 testing. Random analysis of three filters (top, middle, bottom of the box) from a new box of vendor filters before allowing them to be used in field tests is a prudent approach. A box of filters from a given vendor should be screened, and filters from this screened box should be used both for testing and as field blanks in each test scenario to provide the level of quality assurance required for stationary source testing.

A global space-based stratospheric aerosol climatology: 1979-2016

NASA Astrophysics Data System (ADS)

Thomason, Larry W.; Ernest, Nicholas; Millán, Luis; Rieger, Landon; Bourassa, Adam; Vernier, Jean-Paul; Manney, Gloria; Luo, Beiping; Arfeuille, Florian; Peter, Thomas

2018-03-01

We describe the construction of a continuous 38-year record of stratospheric aerosol optical properties. The Global Space-based Stratospheric Aerosol Climatology, or GloSSAC, provided the input data to the construction of the Climate Model Intercomparison Project stratospheric aerosol forcing data set (1979-2014) and we have extended it through 2016 following an identical process. GloSSAC focuses on the Stratospheric Aerosol and Gas Experiment (SAGE) series of instruments through mid-2005, and on the Optical Spectrograph and InfraRed Imager System (OSIRIS) and the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) data thereafter. We also use data from other space instruments and from ground-based, air, and balloon borne instruments to fill in key gaps in the data set. The end result is a global and gap-free data set focused on aerosol extinction coefficient at 525 and 1020 nm and other parameters on an "as available" basis. For the primary data sets, we developed a new method for filling the post-Pinatubo eruption data gap for 1991-1993 based on data from the Cryogenic Limb Array Etalon Spectrometer. In addition, we developed a new method for populating wintertime high latitudes during the SAGE period employing a latitude-equivalent latitude conversion process that greatly improves the depiction of aerosol at high latitudes compared to earlier similar efforts. We report data in the troposphere only when and where it is available. This is primarily during the SAGE II period except for the most enhanced part of the Pinatubo period. It is likely that the upper troposphere during Pinatubo was greatly enhanced over non-volcanic periods and that domain remains substantially under-characterized. We note that aerosol levels during the OSIRIS/CALIPSO period in the lower stratosphere at mid- and high latitudes is routinely higher than what we observed during the SAGE II period. While this period had nearly continuous low-level volcanic activity, it is possible that the enhancement in part reflects deficiencies in the data set. We also expended substantial effort to quality assess the data set and the product is by far the best we have produced. GloSSAC version 1.0 is available in netCDF format at the NASA Atmospheric Data Center at https://eosweb.larc.nasa.gov/. GloSSAC users should cite this paper and the data set DOI (https://doi.org/10.5067/GloSSAC-L3-V1.0).

SuperTroop via I-Port: Distributed Simulation Technology for Combat Development and Training Development

DTIC Science & Technology

1990-08-01

in the 1 -2 Third World.5 (The Joint Chiefs of Staff have undertaken a semantic foray with the term "operational continuum" defined as politico...r.MK" INSTITUTE FOR DEFENSE ANALYSES 1801 N. Beauregard Street, Alexandria, Virginia 22311-1772 90 11 19 1 8 0 t - IDA Log No. HO 90-35316...nmusbatnd Piew 1215Jefm Daw .. gw&y, Sun* 12 4. DAh"W, VA ;22-4302. nd l h oOff0ic of la .ent end Bde Paewl, Peduwon Pwd 1 . AGENCY USE ONLY (L"ve blank

Histocompatibility Typing for the Prediction of Susceptibility to Infectious Disease.

DTIC Science & Technology

1980-06-01

w6/A2, B27 , w4, Cwl Sib B A2, A28 87, 818 (w6) blank A28, B7, w6/A2, 818, w6 12 5.2 HLA -DR typing. HLA -DR (B cell) typing will begin in June after...BACKGROUND 3 D. RESEARCH DESIGN AND PLAN 5 E. RESULTS 6 1. Development of Guidelines and Questionnaire- 6 Computer Form 2. Development of an HLA ...Histocompatibility Testing 7 Serology Laboratory 2.1 Establishment of HLA -A,B,C,DR Typing Trays 7 2.2 Establishment of the Two-Color Fluorescence 9 Method of B

Unidentified line in x-ray spectra of the Andromeda galaxy and Perseus galaxy cluster.

PubMed

Boyarsky, A; Ruchayskiy, O; Iakubovskyi, D; Franse, J

2014-12-19

We report a weak line at 3.52±0.02  keV in x-ray spectra of the Andromeda galaxy and the Perseus galaxy cluster observed by the metal-oxide-silicon (MOS) and p-n (PN) CCD cameras of the XMM-Newton telescope. This line is not known as an atomic line in the spectra of galaxies or clusters. It becomes stronger towards the centers of the objects; is stronger for Perseus than for M31; is absent in the spectrum of a deep "blank sky" data set. Although for each object it is hard to exclude that the feature is due to an instrumental effect or an atomic line, it is consistent with the behavior of a dark matter decay line. Future (non-)detections of this line in multiple objects may help to reveal its nature.

Measurement uncertainty of ester number, acid number and patchouli alcohol of patchouli oil produced in Yogyakarta

NASA Astrophysics Data System (ADS)

Istiningrum, Reni Banowati; Saepuloh, Azis; Jannah, Wirdatul; Aji, Didit Waskito

2017-03-01

Yogyakarta is one of patchouli oil distillation center in Indonesia. The quality of patchouli oil greatly affect its market price. Therefore, testing quality of patchouli oil parameters is an important concern, one through determination of the measurement uncertainty. This study will determine the measurement uncertainty of ester number, acid number and content of patchouli alcohol through a bottom up approach. Source contributor to measurement uncertainty of ester number is a mass of the sample, a blank and sample titration volume, the molar mass of KOH, HCl normality, and replication. While the source contributor of the measurement uncertainty of acid number is the mass of the sample, the sample titration volume, the relative mass and normality of KOH, and repetition. Determination of patchouli alcohol by Gas Chromatography considers the sources of measurement uncertainty only from repeatability because reference materials are not available.

Towards a Biohybrid Lung: Endothelial Cells Promote Oxygen Transfer through Gas Permeable Membranes.

PubMed

Menzel, Sarah; Finocchiaro, Nicole; Donay, Christine; Thiebes, Anja Lena; Hesselmann, Felix; Arens, Jutta; Djeljadini, Suzana; Wessling, Matthias; Schmitz-Rode, Thomas; Jockenhoevel, Stefan; Cornelissen, Christian Gabriel

2017-01-01

In patients with respiratory failure, extracorporeal lung support can ensure the vital gas exchange via gas permeable membranes but its application is restricted by limited long-term stability and hemocompatibility of the gas permeable membranes, which are in contact with the blood. Endothelial cells lining these membranes promise physiological hemocompatibility and should enable prolonged application. However, the endothelial cells increase the diffusion barrier of the blood-gas interface and thus affect gas transfer. In this study, we evaluated how the endothelial cells affect the gas exchange to optimize performance while maintaining an integral cell layer. Human umbilical vein endothelial cells were seeded on gas permeable cell culture membranes and cultivated in a custom-made bioreactor. Oxygen transfer rates of blank and endothelialized membranes in endothelial culture medium were determined. Cell morphology was assessed by microscopy and immunohistochemistry. Both setups provided oxygenation of the test fluid featuring small standard deviations of the measurements. Throughout the measuring range, the endothelial cells seem to promote gas transfer to a certain extent exceeding the blank membranes gas transfer performance by up to 120%. Although the underlying principles hereof still need to be clarified, the results represent a significant step towards the development of a biohybrid lung.

Poly(styrene)-b-poly(DL-lactide) copolymer-based nanoparticles for anticancer drug delivery

PubMed Central

Lee, Jae-Young; Kim, Jung Sun; Cho, Hyun-Jong; Kim, Dae-Duk

2014-01-01

Poly(styrene)-b-poly(DL-lactide) (PS-PDLLA) copolymer-based nanoparticles (NPs) of a narrow size distribution, negative zeta potential, and spherical shape were fabricated for the delivery of docetaxel (DCT). The particle size was consistently maintained in serum for 24 hours and a sustained drug release pattern was observed for 10 days in the tested formulations. The cytotoxicity of the developed blank NPs was negligible in prostate cancer (PC-3) cells. Cellular uptake and distribution of the constructed NPs containing a hydrophobic fluorescent dye was monitored by confocal laser scanning microscopy (CLSM) for 24 hours. Anti-tumor efficacy of the PS-PDLLA/DCT NPs in PC-3 cells was significantly more potent than that of the group treated with commercially available DCT, Taxotere® (P<0.05). Blood biochemistry tests showed that no serious toxicity was observed with the blank NPs in the liver and kidney. In a pharmacokinetic study of DCT in rats, in vivo clearance of PS-PDLLA/DCT NPs decreased while the half-life in blood increased compared to the Taxotere-treated group (P<0.05). The PS-PDLLA NPs are expected to be a biocompatible and efficient nano-delivery system for anticancer drugs. PMID:24940058

Application of a molecularly imprinted polymer for the extraction of kukoamine a from potato peels.

PubMed

Piletska, Elena V; Burns, Rosemary; Terry, Leon A; Piletsky, Sergey A

2012-01-11

A molecularly imprinted polymer (MIP) for the purification of N(1),N(12)-bis(dihydrocaffeoyl)spermine (kukoamine A) was computationally designed and tested. The properties of the polymer were characterized. The protocol of the solid phase extraction (SPE) of kukoamine A from potato peels was optimized. A HPLC-MS method for the quantification of kukoamine A was developed and used for all optimization studies. The capacity of the MIP in relation to kukoamine A from the potato peels extract was estimated at 54 mg/g of the polymer. The kukoamine A purified from potato extract using MIP was exceptionally pure (≈ 90%). Although the corresponding blank polymer was less selective than the MIP for the extraction of kukoamine A from the potato extract, it was shown that the blank polymer could be effectively used for the purification of the crude synthetic kukoamine (polymer capacity = 80 mg of kukoamine A/g of the adsorbent, kukoamine A purity ≈ 86%). Therefore, selective adsorbents could be computationally designed for other plant products, allowing their purification in quantities that would be sufficient for more detailed studies and potential practical applications.

Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

NASA Astrophysics Data System (ADS)

Vollmer, R.; Palm, C.

2017-09-01

The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

ZERODUR iso-grid design of a 3m class light weighted mirror blank for the E-ELT M5

NASA Astrophysics Data System (ADS)

Jedamzik, Ralf; Leys, Antoine; Seibert, Volker; Westerhoff, Thomas

2014-07-01

The tip and tilt M5 mirror of the European Extremly Large Telescope (E-ELT) requires a demanding approach in light weighting. The approximately 3 m x 2.5 m elliptical plano mirror is specified to a weight of less than 500 kg with high Eigenfrequencies and low deformation under different inclination angles. In 2011 SCHOTT has presented a study to develop a design for the M5 mirror blank of the ESO E-ELT. The design presented was based on a radial square design to achieve the best compromise between performance and manufacturability. With the fabrication of a prototype section SCHOTT demonstrated its capability to manufacture the demanding features including pockets with 350 mm depth, thin walls and sloped pocket bottoms. Now 3 years later SCHOTT presents an iso-grid based design that is in accordance with the manufacturability progress that has been demonstrated in various ELZM (Extremely Lightweighted ZERODUR Mirrors) publications in the last two years. The achievements on the specified mechanical parameters are compared to the first approach from 2011. In this paper the results are presented and the performance parameters are discussed.

Method and apparatus for inspecting an EUV mask blank

DOEpatents

Goldberg, Kenneth A.

2005-11-08

An apparatus and method for at-wavelength EUV mask-blank characterization for inspection of moderate and low spatial frequency coating uniformity using a synchrotron or other source of EUV light. The apparatus provides for rapid, non-destruction, non-contact, at-wavelength qualification of large mask areas, and can be self-calibrating or be calibrated to well-characterized reference samples. It can further check for spatial variation of mask reflectivity or for global differences among masks. The apparatus and method is particularly suited for inspection of coating uniformity and quality and can detect defects in the order of 50 .mu.m and above.