Verification of combined thermal-hydraulic and heat conduction analysis code FLOWNET/TRUMP

NASA Astrophysics Data System (ADS)

Maruyama, Soh; Fujimoto, Nozomu; Kiso, Yoshihiro; Murakami, Tomoyuki; Sudo, Yukio

1988-09-01

This report presents the verification results of the combined thermal-hydraulic and heat conduction analysis code, FLOWNET/TRUMP which has been utilized for the core thermal hydraulic design, especially for the analysis of flow distribution among fuel block coolant channels, the determination of thermal boundary conditions for fuel block stress analysis and the estimation of fuel temperature in the case of fuel block coolant channel blockage accident in the design of the High Temperature Engineering Test Reactor(HTTR), which the Japan Atomic Energy Research Institute has been planning to construct in order to establish basic technologies for future advanced very high temperature gas-cooled reactors and to be served as an irradiation test reactor for promotion of innovative high temperature new frontier technologies. The verification of the code was done through the comparison between the analytical results and experimental results of the Helium Engineering Demonstration Loop Multi-channel Test Section(HENDEL T(sub 1-M)) with simulated fuel rods and fuel blocks.

Design development of graphite primary structures enables SSTO success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biagiotti, V.A.; Yahiro, J.S.; Suh, D.E.

1997-01-01

This paper describes the development of a graphite composite wing and a graphite composite intertank primary structure for application toward Single-Stage to Orbit space vehicles such as those under development in NASA{close_quote}s X-33/Reusable Launch Vehicle (RLV) Program. The trade study and designs are based on a Rockwell vertical take-off and horizontal landing (VTHL) wing-body RLV vehicle. Northrop Grumman{close_quote}s approach using a building block development technique is described. Composite Graphite/Bismaleimide (Gr/BMI) material characterization test results are presented. Unique intertank and wing composite subcomponent test article designs are described and test results to date are presented. Wing and intertank Full Scale Sectionmore » Test Article (FSTA) objectives and designs are outlined. Trade studies, supporting building block testing, and FSTA demonstrations combine to develop graphite primary structure composite technology that enables developing X-33/RLV design programs to meet critical SSTO structural weight and operations performance criteria. {copyright} {ital 1997 American Institute of Physics.}« less

Visuo-Spatial Performance in Autism: A Meta-Analysis

ERIC Educational Resources Information Center

Muth, Anne; Hönekopp, Johannes; Falter, Christine M.

2014-01-01

Visuo-spatial skills are believed to be enhanced in autism spectrum disorders (ASDs). This meta-analysis tests the current state of evidence for Figure Disembedding, Block Design, Mental Rotation and Navon tasks in ASD and neurotypicals. Block Design (d = 0.32) and Figure Disembedding (d = 0.26) showed superior performance for ASD with large…

Powered Explicit Guidance Modifications and Enhancements for Space Launch System Block-1 and Block-1B Vehicles

NASA Technical Reports Server (NTRS)

Von der Porten, Paul; Ahmad, Naeem; Hawkins, Matt; Fill, Thomas

2018-01-01

NASA is currently building the Space Launch System (SLS) Block-1 launch vehicle for the Exploration Mission 1 (EM-1) test flight. NASA is also currently designing the next evolution of SLS, the Block-1B. The Block-1 and Block-1B vehicles will use the Powered Explicit Guidance (PEG) algorithm (of Space Shuttle heritage) for closed loop guidance. To accommodate vehicle capabilities and design for future evolutions of SLS, modifications were made to PEG for Block-1 to handle multi-phase burns, provide PEG updated propulsion information, and react to a core stage engine out. In addition, due to the relatively low thrust-to-weight ratio of the Exploration Upper Stage (EUS) and EUS carrying out Lunar Vicinity and Earth Escape missions, certain enhancements to the Block-1 PEG algorithm are needed to perform Block-1B missions to account for long burn arcs and target translunar and hyperbolic orbits. This paper describes the design and implementation of modifications to the Block-1 PEG algorithm as compared to Space Shuttle. Furthermore, this paper illustrates challenges posed by the Block-1B vehicle and the required PEG enhancements. These improvements make PEG capable for use on the SLS Block-1B vehicle as part of the Guidance, Navigation, and Control (GN&C) System.

Large Block Test Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, W

2001-12-01

This report documents the Large-Block Test (LBT) conducted at Fran Ridge near Yucca Mountain, Nevada. The LBT was a thermal test conducted on an exposed block of middle non-lithophysal Topopah Spring tuff (Tptpmn) and was designed to assist in understanding the thermal-hydrological-mechanical-chemical (THMC) processes associated with heating and then cooling a partially saturated fractured rock mass. The LBT was unique in that it was a large (3 x 3 x 4.5 m) block with top and sides exposed. Because the block was exposed at the surface, boundary conditions on five of the six sides of the block were relatively wellmore » known and controlled, making this test both easier to model and easier to monitor. This report presents a detailed description of the test as well as analyses of the data and conclusions drawn from the test. The rock block that was tested during the LBT was exposed by excavation and removal of the surrounding rock. The block was characterized and instrumented, and the sides were sealed and insulated to inhibit moisture and heat loss. Temperature on the top of the block was also controlled. The block was heated for 13 months, during which time temperature, moisture distribution, and deformation were monitored. After the test was completed and the block cooled down, a series of boreholes were drilled, and one of the heater holes was over-cored to collect samples for post-test characterization of mineralogy and mechanical properties. Section 2 provides background on the test. Section 3 lists the test objectives and describes the block site, the site configuration, and measurements made during the test. Section 3 also presents a chronology of events associated with the LBT, characterization of the block, and the pre-heat analyses of the test. Section 4 describes the fracture network contained in the block. Section 5 describes the heating/cooling system used to control the temperature in the block and presents the thermal history of the block during the test. Sections 5 through 9 report the measurements made on the block during the preheating, heating, and cooling phases. These measurements include temperature, thermal conductivity and diffusivity, hydrological measurements (electrical resistivity, neutron logging, gas pressure, and relative humidity), geomechanics, selected chemical analyses, and microbial activity. These sections also include analyses and simulations of the block behavior. Finally, conclusions are presented in Section 10. Complete data sets were submitted during the time the test was conducted. The data tracking numbers (DTNs) of all of the data are presented in Table 1-1.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, Steven; Valera-Leon, Carlos; Dechev, Damian

The vector is a fundamental data structure, which provides constant-time access to a dynamically-resizable range of elements. Currently, there exist no wait-free vectors. The only non-blocking version supports only a subset of the sequential vector API and exhibits significant synchronization overhead caused by supporting opposing operations. Since many applications operate in phases of execution, wherein each phase only a subset of operations are used, this overhead is unnecessary for the majority of the application. To address the limitations of the non-blocking version, we present a new design that is wait-free, supports more of the operations provided by the sequential vector,more » and provides alternative implementations of key operations. These alternatives allow the developer to balance the performance and functionality of the vector as requirements change throughout execution. Compared to the known non-blocking version and the concurrent vector found in Intel’s TBB library, our design outperforms or provides comparable performance in the majority of tested scenarios. Over all tested scenarios, the presented design performs an average of 4.97 times more operations per second than the non-blocking vector and 1.54 more than the TBB vector. In a scenario designed to simulate the filling of a vector, performance improvement increases to 13.38 and 1.16 times. This work presents the first ABA-free non-blocking vector. Finally, unlike the other non-blocking approach, all operations are wait-free and bounds-checked and elements are stored contiguously in memory.« less

An Efficient Wait-Free Vector

DOE PAGES

Feldman, Steven; Valera-Leon, Carlos; Dechev, Damian

2016-03-01

The vector is a fundamental data structure, which provides constant-time access to a dynamically-resizable range of elements. Currently, there exist no wait-free vectors. The only non-blocking version supports only a subset of the sequential vector API and exhibits significant synchronization overhead caused by supporting opposing operations. Since many applications operate in phases of execution, wherein each phase only a subset of operations are used, this overhead is unnecessary for the majority of the application. To address the limitations of the non-blocking version, we present a new design that is wait-free, supports more of the operations provided by the sequential vector,more » and provides alternative implementations of key operations. These alternatives allow the developer to balance the performance and functionality of the vector as requirements change throughout execution. Compared to the known non-blocking version and the concurrent vector found in Intel’s TBB library, our design outperforms or provides comparable performance in the majority of tested scenarios. Over all tested scenarios, the presented design performs an average of 4.97 times more operations per second than the non-blocking vector and 1.54 more than the TBB vector. In a scenario designed to simulate the filling of a vector, performance improvement increases to 13.38 and 1.16 times. This work presents the first ABA-free non-blocking vector. Finally, unlike the other non-blocking approach, all operations are wait-free and bounds-checked and elements are stored contiguously in memory.« less

An International Round-Robin Test of NDE Reliability for PWSCC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schuster, George J.; Cumblidge, Stephen E.; Doctor, Steven R.

2007-12-01

In this paper we describe the round robin tests that have been designed and are being conducted in the international program. Participants in the PINC have offered more than 30 test blocks for use in round-robin tests of NDE effectiveness. The test blocks have more than 130 flaws in nickel-base weld metal that are intended to simulate PWSCC in a variety of component geometries. NDE techniques representative of current in-service inspections are being applied, along with emerging NDE approaches.

Design and analysis of lifting tool assemblies to lift different engine block

NASA Astrophysics Data System (ADS)

Sawant, Arpana; Deshmukh, Nilaj N.; Chauhan, Santosh; Dabhadkar, Mandar; Deore, Rupali

2017-07-01

Engines block are required to be lifted from one place to another while they are being processed. The human effort required for this purpose is more and also the engine block may get damaged if it is not handled properly. There is a need for designing a proper lifting tool which will be able to conveniently lift the engine block and place it at the desired position without any accident and damage to the engine block. In the present study lifting tool assemblies are designed and analyzed in such way that it may lift different categories of engine blocks. The lifting tool assembly consists of lifting plate, lifting ring, cap screws and washers. A parametric model and assembly of Lifting tool is done in 3D modelling software CREO 2.0 and analysis is carried out in ANSYS Workbench 16.0. A test block of weight equivalent to that of an engine block is considered for the purpose of analysis. In the preliminary study, without washer the stresses obtained on the lifting tool were more than the safety margin. In the present design, washers were used with appropriate dimensions which helps to bring down the stresses on the lifting tool within the safety margin. Analysis is carried out to verify that tool design meets the ASME BTH-1 required safety margin.

Permutation testing of orthogonal factorial effects in a language-processing experiment using fMRI.

PubMed

Suckling, John; Davis, Matthew H; Ooi, Cinly; Wink, Alle Meije; Fadili, Jalal; Salvador, Raymond; Welchew, David; Sendur, Levent; Maxim, Vochita; Bullmore, Edward T

2006-05-01

The block-paradigm of the Functional Image Analysis Contest (FIAC) dataset was analysed with the Brain Activation and Morphological Mapping software. Permutation methods in the wavelet domain were used for inference on cluster-based test statistics of orthogonal contrasts relevant to the factorial design of the study, namely: the average response across all active blocks, the main effect of speaker, the main effect of sentence, and the interaction between sentence and speaker. Extensive activation was seen with all these contrasts. In particular, different vs. same-speaker blocks produced elevated activation in bilateral regions of the superior temporal lobe and repetition suppression for linguistic materials (same vs. different-sentence blocks) in left inferior frontal regions. These are regions previously reported in the literature. Additional regions were detected in this study, perhaps due to the enhanced sensitivity of the methodology. Within-block sentence suppression was tested post-hoc by regression of an exponential decay model onto the extracted time series from the left inferior frontal gyrus, but no strong evidence of such an effect was found. The significance levels set for the activation maps are P-values at which we expect <1 false-positive cluster per image. Nominal type I error control was verified by empirical testing of a test statistic corresponding to a randomly ordered design matrix. The small size of the BOLD effect necessitates sensitive methods of detection of brain activation. Permutation methods permit the necessary flexibility to develop novel test statistics to meet this challenge.

Precocious realists: perceptual and cognitive characteristics associated with drawing talent in non-autistic children

PubMed Central

Drake, Jennifer E.; Winner, Ellen

2009-01-01

A local processing bias in the block design task and in drawing strategy has been used to account for realistic drawing skill in individuals with autism. We investigated whether the same kind of local processing bias is seen in typically developing children with unusual skill in realistic graphic representation. Forty-three 5–11-year-olds who drew a still life completed a version of the block design task in both standard and segmented form, were tested for their memory for the block design items, and were given the Kaufmann Brief Intelligence Test-II. Children were classified as gifted, moderately gifted or typical on the basis of the level of realism in their drawings. Similar to autistic individuals, the gifted group showed a local processing bias in the block design task. But unlike autistic individuals, the gifted group showed a global advantage in the visual memory task and did not use a local drawing strategy; in addition, their graphic realism skill was related to verbal IQ. Differences in the extent of local processing bias in autistic and typically developing children with drawing talent are discussed. PMID:19528030

Key Topics for High-Lift Research: A Joint Wind Tunnel/Flight Test Approach

NASA Technical Reports Server (NTRS)

Fisher, David; Thomas, Flint O.; Nelson, Robert C.

1996-01-01

Future high-lift systems must achieve improved aerodynamic performance with simpler designs that involve fewer elements and reduced maintenance costs. To expeditiously achieve this, reliable CFD design tools are required. The development of useful CFD-based design tools for high lift systems requires increased attention to unresolved flow physics issues. The complex flow field over any multi-element airfoil may be broken down into certain generic component flows which are termed high-lift building block flows. In this report a broad spectrum of key flow field physics issues relevant to the design of improved high lift systems are considered. It is demonstrated that in-flight experiments utilizing the NASA Dryden Flight Test Fixture (which is essentially an instrumented ventral fin) carried on an F-15B support aircraft can provide a novel and cost effective method by which both Reynolds and Mach number effects associated with specific high lift building block flows can be investigated. These in-flight high lift building block flow experiments are most effective when performed in conjunction with coordinated ground based wind tunnel experiments in low speed facilities. For illustrative purposes three specific examples of in-flight high lift building block flow experiments capable of yielding a high payoff are described. The report concludes with a description of a joint wind tunnel/flight test approach to high lift aerodynamics research.

Thermal Design Overview of the Mars Exploration Rover Project

NASA Technical Reports Server (NTRS)

Tsuyuki, Glenn

2002-01-01

Contents include the following: Mission Overview. Thermal Environments. Driving Thermal Requirements. Thermal Design Approach. Thermal Control Block Diagram. Thermal Design Description. Thermal Analysis Results Summary. Testing Plans. Issues & Concerns.

High Temperature Gas-Cooled Test Reactor Point Design: Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterbentz, James William; Bayless, Paul David; Nelson, Lee Orville

2016-01-01

A point design has been developed for a 200-MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched uranium oxycarbide fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technology readiness level, licensing approach, and costs of the test reactor point design.

High Temperature Gas-Cooled Test Reactor Point Design: Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterbentz, James William; Bayless, Paul David; Nelson, Lee Orville

2016-03-01

A point design has been developed for a 200-MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched uranium oxycarbide fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technology readiness level, licensing approach, and costs of the test reactor point design.

A Quick Assessment of Visuospatial Abilities in Adolescents Using the Design Organization Test (DOT).

PubMed

Burggraaf, Rudolf; Frens, Maarten A; Hooge, Ignace T C; van der Geest, Jos N

2016-01-01

Tests measuring visuospatial abilities have shown that these abilities increase during adolescence. Unfortunately, the Block Design test and other such tests are complicated and time-consuming to administer, making them unsuitable for use with large groups of restless adolescents. The results of the Design Organization Test (DOT), a quick pen-and-paper test, have been shown to correlate with those of the Block Design test. A group of 198 healthy adolescents (110 male and 88 female) aged 12 to 19 years old participated in this study. A slightly modified version of the DOT has been used in which we shortened the administration time to avoid a ceiling effect in the score. Scores show a linear increase with age (on average 2.0 points per year, r = .61) independent of sex. Scores did not differ between individual setting and group setting. Thus, the DOT is a simple and effective way to assess visuospatial ability in large groups, such as in schools, and it can be easily administered year after year to follow the development of students.

Block 2 SRM conceptual design studies. Volume 1, Book 2: Preliminary development and verification plan

NASA Technical Reports Server (NTRS)

1986-01-01

Activities that will be conducted in support of the development and verification of the Block 2 Solid Rocket Motor (SRM) are described. Development includes design, fabrication, processing, and testing activities in which the results are fed back into the project. Verification includes analytical and test activities which demonstrate SRM component/subassembly/assembly capability to perform its intended function. The management organization responsible for formulating and implementing the verification program is introduced. It also identifies the controls which will monitor and track the verification program. Integral with the design and certification of the SRM are other pieces of equipment used in transportation, handling, and testing which influence the reliability and maintainability of the SRM configuration. The certification of this equipment is also discussed.

Overview of the Space Launch System Ascent Aeroacoustic Environment Test Program

NASA Technical Reports Server (NTRS)

Herron, Andrew J.; Crosby, William A.; Reed, Darren K.

2016-01-01

Characterization of accurate flight vehicle unsteady aerodynamics is critical for component and secondary structure vibroacoustic design. The Aerosciences Branch at the National Aeronautics and Space Administration (NASA) Marshall Space Flight Center has conducted a test at the NASA Ames Research Center (ARC) Unitary Plan Wind Tunnels (UPWT) to determine such ascent aeroacoustic environments for the Space Launch System (SLS). Surface static pressure measurements were also collected to aid in determination of local environments for venting, CFD substantiation, and calibration of the flush air data system located on the launch abort system. Additionally, this test supported a NASA Engineering and Safety Center study of alternate booster nose caps. Testing occurred during two test campaigns: August - September 2013 and December 2013 - January 2014. Four primary model configurations were tested for ascent aeroacoustic environment definition. The SLS Block 1 vehicle was represented by a 2.5% full stack model and a 4% truncated model. Preliminary Block 1B payload and manned configurations were also tested, using 2.5% full stack and 4% truncated models respectively. This test utilized the 11 x 11 foot transonic and 9 x 7 foot supersonic tunnel sections at the ARC UPWT to collect data from Mach 0.7 through 2.5 at various total angles of attack. SLS Block 1 design environments were developed primarily using these data. SLS Block 1B preliminary environments have also been prepared using these data. This paper discusses the test and analysis methodology utilized, with a focus on the unsteady data collection and processing.

Block 3 X-band receiver-exciter

NASA Technical Reports Server (NTRS)

Johns, C. E.

1987-01-01

The development of an X-band exciter, for use in the X-Band Uplink Subsystem, was completed. The exciter generates the drive signal for the X-band transmitter and also generates coherent test signals for the S- and X-band Block 3 translator and a Doppler reference signal for the Doppler extractor system. In addition to the above, the exciter generates other reference signals that are described. Also presented is an overview of the exciter design and some test data taken on the prototype. A brief discussion of the Block 3 Doppler extractor is presented.

Design Language for Digital Systems

NASA Technical Reports Server (NTRS)

Shiva, S. G.

1985-01-01

Digital Systems Design Language (DDL) is convenient hardware description language for developing and testing digital designs and for inputting design details into design automation system. Describes digital systems at gate, register transfer, and combinational block levels. DDL-based programs written in FORTRAN IV for batch execution.

Model based design introduction: modeling game controllers to microprocessor architectures

NASA Astrophysics Data System (ADS)

Jungwirth, Patrick; Badawy, Abdel-Hameed

2017-04-01

We present an introduction to model based design. Model based design is a visual representation, generally a block diagram, to model and incrementally develop a complex system. Model based design is a commonly used design methodology for digital signal processing, control systems, and embedded systems. Model based design's philosophy is: to solve a problem - a step at a time. The approach can be compared to a series of steps to converge to a solution. A block diagram simulation tool allows a design to be simulated with real world measurement data. For example, if an analog control system is being upgraded to a digital control system, the analog sensor input signals can be recorded. The digital control algorithm can be simulated with the real world sensor data. The output from the simulated digital control system can then be compared to the old analog based control system. Model based design can compared to Agile software develop. The Agile software development goal is to develop working software in incremental steps. Progress is measured in completed and tested code units. Progress is measured in model based design by completed and tested blocks. We present a concept for a video game controller and then use model based design to iterate the design towards a working system. We will also describe a model based design effort to develop an OS Friendly Microprocessor Architecture based on the RISC-V.

Investigation of panel-to-panel connections and block-outs for full-depth precast concrete bridge decks.

DOT National Transportation Integrated Search

2015-06-01

Experimental tests were performed at Virginia Tech to investigate transverse panel-to-panel connections and horizontal shear : connector block-outs for full-depth precast concrete bridge deck panels. The connections were designed for a deck replaceme...

Using R in experimental design with BIBD: An application in health sciences

NASA Astrophysics Data System (ADS)

Oliveira, Teresa A.; Francisco, Carla; Oliveira, Amílcar; Ferreira, Agostinho

2016-06-01

Considering the implementation of an Experimental Design, in any field, the experimenter must pay particular attention and look for the best strategies in the following steps: planning the design selection, conduct the experiments, collect observed data, proceed to analysis and interpretation of results. The focus is on providing both - a deep understanding of the problem under research and a powerful experimental process at a reduced cost. Mainly thanks to the possibility of allowing to separate variation sources, the importance of Experimental Design in Health Sciences is strongly recommended since long time. Particular attention has been devoted to Block Designs and more precisely to Balanced Incomplete Block Designs - in this case the relevance states from the fact that these designs allow testing simultaneously a number of treatments bigger than the block size. Our example refers to a possible study of inter reliability of the Parkinson disease, taking into account the UPDRS (Unified Parkinson's disease rating scale) in order to test if there are significant differences between the specialists who evaluate the patients performances. Statistical studies on this disease were described for example in Richards et al (1994), where the authors investigate the inter-rater Reliability of the Unified Parkinson's Disease Rating Scale Motor Examination. We consider a simulation of a practical situation in which the patients were observed by different specialists and the UPDRS on assessing the impact of Parkinson's disease in patients was observed. Assigning treatments to the subjects following a particular BIBD(9,24,8,3,2) structure, we illustrate that BIB Designs can be used as a powerful tool to solve emerging problems in this area. Once a structure with repeated blocks allows to have some block contrasts with minimum variance, see Oliveira et al. (2006), the design with cardinality 12 was selected for the example. R software was used for computations.

Response of crapemyrtle varieties to Cercospora leaf spot, 2015

USDA-ARS?s Scientific Manuscript database

Crapemyrtle varieties, Lagerstroemia spp., were evaluated for Cercospora leaf spot in two field test evaluations, planted in either 2004 or 2011 at the Otis L. Floyd Nursery Research Center in McMinnville, TN. The experimental designs for both test evaluations were a randomized complete block design...

High-Temperature Gas-Cooled Test Reactor Point Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterbentz, James William; Bayless, Paul David; Nelson, Lee Orville

2016-04-01

A point design has been developed for a 200 MW high-temperature gas-cooled test reactor. The point design concept uses standard prismatic blocks and 15.5% enriched UCO fuel. Reactor physics and thermal-hydraulics simulations have been performed to characterize the capabilities of the design. In addition to the technical data, overviews are provided on the technological readiness level, licensing approach and costs.

SU-E-T-243: Design of a Novel Testing Port for Radiation Protection and Shielding Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanny, S; Parsai, E; Harrell, D

2015-06-15

Purpose: The majority of radiation shielding research utilizes Monte Carlo simulation because of the difficulty in eliminating secondary radiations from measurements. We have designed a test port into a primary barrier of our newest vault to allow for shielding measurements while ensuring adequate protection to the public and staff during normal machine operation. This port allows for measurement of attenuation values of shielding materials, differential dose albedos, and radiation scatter fractions. Methods: The vault design utilized the maze as part of a compound primary barrier. The test port is contained within the maze and is centered along isocenter. The innermore » 30 cm has a 20×20 cm{sup 2} opening, while the remaining length has a 30×30 cm{sup 2} opening. The block that contains the port has a density of 200 pcf to minimize internal scatter. The 30×30 cm{sup 2} opening is occupied by removable 215 pcf concrete blocks. The innermost and outermost blocks activate an interlock wired into the beam-enable loop. This disallows beam-on in treatment mode if the interlock isn’t closed. The interlock can be overridden in service mode, or by-passed via an override switch in case of circuit failure. Results: The test port was installed in August. The beam is disabled when the interlock is tripped. Measurements taken when the primary beam is not incident on the port are indistinguishable from background. Ambient dose levels surrounding the vault with the designed shielding blocks in place are all within allowable limits for occupational workers. Conclusions: We have designed and installed a unique testing port for radiation protection and shielding measurements. This port is appropriately interlocked and designed to mitigate any risks of incidental exposure to staff or members of the public. The test port design allows measurements with “good geometry” and efficient removal of contaminating sources of radiation present in many shielding measurements. Daniel Harrell and Jim Noller are employees of Shielding Construction Solutions, Inc, the shielding construction company that built the vault discussed in this abstract. Manjit Chopra is an employee of Universal Minerals International, Inc, the company that provided the aggregates for the high density concretes used in the vault construction.« less

Characterizing permanent magnet blocks with Helmholtz coils

NASA Astrophysics Data System (ADS)

Carnegie, D. W.; Timpf, J.

1992-08-01

Most of the insertion devices to be installed at the Advanced Photon Source will utilize permanent magnets in their magnetic structures. The quality of the spectral output is sensitive to the errors in the field of the device which are related to variations in the magnetic properties of the individual blocks. The Advanced Photon Source will have a measurement facility to map the field in the completed insertion devices and equipment to test and modify the magnetic strength of the individual magnet blocks. One component of the facility, the Helmholtz coil permanent magnet block measurement system, has been assembled and tested. This system measures the total magnetic moment vector of a block with a precision better than 0.01% and a directional resolution of about 0.05°. The design and performance of the system will be presented.

Transforming information from silicon testing and design characterization into numerical data sets for yield learning

NASA Astrophysics Data System (ADS)

Yang, Thomas; Shen, Yang; Zhang, Yifan; Sweis, Jason; Lai, Ya-Chieh

2017-03-01

Silicon testing results are regularly collected for a particular lot of wafers to study yield loss from test result diagnostics. Product engineers will analyze the diagnostic results and perform a number of physical failure analyses to detect systematic defects which cause yield loss for these sets of wafers in order to feedback the information to process engineers for process improvements. Most of time, the systematic defects that are detected are major issues or just one of the causes for the overall yield loss. This paper will present a working flow for using design analysis techniques combined with diagnostic methods to systematically transform silicon testing information into physical layout information. A new set of the testing results are received from a new lot of wafers for the same product. We can then correlate all the diagnostic results from different periods of time to check which blocks or nets have been highlighted or stop occurring on the failure reports in order to monitor process changes which impact the yield. The design characteristic analysis flow is also implemented to find 1) the block connections on a design that have failed electrical test or 2) frequently used cells that been highlighted multiple times.

Exact Test of Independence Using Mutual Information

DTIC Science & Technology

2014-05-23

1000 × 0.05 = 50. Entropy 2014, 16 2844 Importantly, the permutation test, which does not preserve Markov order, resulted in 489 Type I errors! Using...Block 13 ARO Report Number Block 13: Supplementary Note © 2014 . Published in Entropy , Vol. Ed. 0 16, (7) (2014), (, (7). DoD Components reserve a...official Department of the Army position, policy or decision, unless so designated by other documentation. ... Entropy 2014, 16, 2839-2849; doi:10.3390

Hydrogen sensors based on catalytic metals

NASA Astrophysics Data System (ADS)

Beklemyshev, V. I.; Berezine, V.; Bykov, Victor A.; Kiselev, L.; Makhonin, I.; Pevgov, V.; Pustovoy, V.; Semynov, A.; Sencov, Y.; Shkuropat, I.; Shokin, A.

1999-11-01

On the base of microelectronical and micromechanical technology were designed and developed converters of hydrogen concentration to electrical signals. The devices of controlling concentration of hydrogen in the air were developed. These devices were applied for ensuring fire and explosion security of complex technological teste of missile oxygen-hydrogen engine, developed for cryogenic accelerations block. The sensor block of such device was installed directly on the armor-plate, to which was attached tested engine.

InChIKey collision resistance: an experimental testing

PubMed Central

2012-01-01

InChIKey is a 27-character compacted (hashed) version of InChI which is intended for Internet and database searching/indexing and is based on an SHA-256 hash of the InChI character string. The first block of InChIKey encodes molecular skeleton while the second block represents various kinds of isomerism (stereo, tautomeric, etc.). InChIKey is designed to be a nearly unique substitute for the parent InChI. However, a single InChIKey may occasionally map to two or more InChI strings (collision). The appearance of collision itself does not compromise the signature as collision-free hashing is impossible; the only viable approach is to set and keep a reasonable level of collision resistance which is sufficient for typical applications. We tested, in computational experiments, how well the real-life InChIKey collision resistance corresponds to the theoretical estimates expected by design. For this purpose, we analyzed the statistical characteristics of InChIKey for datasets of variable size in comparison to the theoretical statistical frequencies. For the relatively short second block, an exhaustive direct testing was performed. We computed and compared to theory the numbers of collisions for the stereoisomers of Spongistatin I (using the whole set of 67,108,864 isomers and its subsets). For the longer first block, we generated, using custom-made software, InChIKeys for more than 3 × 1010 chemical structures. The statistical behavior of this block was tested by comparison of experimental and theoretical frequencies for the various four-letter sequences which may appear in the first block body. From the results of our computational experiments we conclude that the observed characteristics of InChIKey collision resistance are in good agreement with theoretical expectations. PMID:23256896

InChIKey collision resistance: an experimental testing.

PubMed

Pletnev, Igor; Erin, Andrey; McNaught, Alan; Blinov, Kirill; Tchekhovskoi, Dmitrii; Heller, Steve

2012-12-20

InChIKey is a 27-character compacted (hashed) version of InChI which is intended for Internet and database searching/indexing and is based on an SHA-256 hash of the InChI character string. The first block of InChIKey encodes molecular skeleton while the second block represents various kinds of isomerism (stereo, tautomeric, etc.). InChIKey is designed to be a nearly unique substitute for the parent InChI. However, a single InChIKey may occasionally map to two or more InChI strings (collision). The appearance of collision itself does not compromise the signature as collision-free hashing is impossible; the only viable approach is to set and keep a reasonable level of collision resistance which is sufficient for typical applications.We tested, in computational experiments, how well the real-life InChIKey collision resistance corresponds to the theoretical estimates expected by design. For this purpose, we analyzed the statistical characteristics of InChIKey for datasets of variable size in comparison to the theoretical statistical frequencies. For the relatively short second block, an exhaustive direct testing was performed. We computed and compared to theory the numbers of collisions for the stereoisomers of Spongistatin I (using the whole set of 67,108,864 isomers and its subsets). For the longer first block, we generated, using custom-made software, InChIKeys for more than 3 × 1010 chemical structures. The statistical behavior of this block was tested by comparison of experimental and theoretical frequencies for the various four-letter sequences which may appear in the first block body.From the results of our computational experiments we conclude that the observed characteristics of InChIKey collision resistance are in good agreement with theoretical expectations.

Block 4 solar cell module design and test specification for intermediate load center applications

NASA Technical Reports Server (NTRS)

1978-01-01

Requirements for performance of terrestrial solar cell modules intended for use in various test applications are established. During the 1979-80 time period, such applications are expected to be in the 20 to 500 kilowatt size range. A series of characterization and qualification tests necessary to certify the module design for production, and the necessary performance test for acceptance of modules are specified.

Evidence of Blocking with Geometric Cues in a Virtual Watermaze

ERIC Educational Resources Information Center

Redhead, Edward S.; Hamilton, Derek A.

2009-01-01

Three computer based experiments, testing human participants in a non-immersive virtual watermaze task, used a blocking design to assess whether two sets of geometric cues would compete in a manner described by associative models of learning. In stage 1, participants were required to discriminate between visually distinct platforms. In stage 2,…

Analysis of Glenoid Fixation with Anatomic Total Shoulder Arthroplasty in an Extreme Cyclic Loading Scenario.

PubMed

Roche, Christopher P; Staunch, Cameron; Hahn, William; Grey, Sean G; Flurin, Pierre-Henri; Wright, Thomas W; Zuckerman, Joseph D

2015-12-01

ASTM F2028-14 was adopted to recom mend a cyclic eccentric glenoid edge loading test that simulates the rocking horse loading mechanism beleived to cause aTSA glenoid loosening. While this method accurately simulates that failure mechanism, the recommended 750 N load may not be sufficient to simulate worst-case loading magnitudes, and the recommended 100,000 cycles may not be sufficient to simulate device fatigue-related failure modes. Finally, if greater loading magnitude or a larger number of cycles is performed, the recommended substrate density may not be sufficiently strong to support the elevated loads and cycles. To this end, a new test method is proposed to supplement ASTM F2028-14. A series of cyclic tests were performed to evaluate the long-term fixation strength of two different hybrid glenoid designs in both low (15 pcf) and high (30 pcf) density polyurethane blocks at elevated loads relative to ASTM F2028-14. To simulate a worst case clinical condition in which the humeral head is superiorly migrated, a cyclic load was applied to the superior glenoid rim to induce a maximum torque on the fixation pegs for three different cyclic loading tests: 1. 1,250 N load for 0.75 M cycles in a 15 pcf block, 2. 1,250 N load for 1.5 M cycles in a 30 pcf block, and 3. 2,000 N load for 0.65 M cycles in a 30 pcf block. All devices completed cyclic loading without failure, fracture, or loss of fixation regardless of glenoid design, polyurethane density, loading magnitude, or cycle length. No significant difference in post-cyclic displacement was noted between designs in any of the three tests. Post-cyclic radiographs demonstrated that each device maintained fixa - tion with the metal pegs within the bone-substitute blocks with no fatigue related failures. These results demonstrate that both cemented hybrid glenoids maintained fixation when tested according to each cyclic loading scenario, with no difference in post-cyclic displacement observed between designs. The lack of fatigue-related failures in these elevated load and high cycle test scenarios are promising, as are the relatively low displacements given the extreme nature of each test. This cyclic loading method is intended to supplement the ASTM F2028-14 standard that adequately simulates the rocking horse loading mechanism but may not adequately simulate the fatigue-related failure modes.

List blocking and longer retention intervals reveal an influence of gist processing for lexically ambiguous critical lures

PubMed Central

McNabb, Jaimie; Hutchison, Keith A.

2016-01-01

In two experiments, we examined veridical and false memory for lists of associates from two meanings (e.g., stumble, trip, harvest, pumpkin, etc.) that converged upon a single, lexically ambiguous critical lure (e.g., fall), in order to compare the activation-monitoring and fuzzy-trace false memory accounts. In Experiment 1, we presented study lists that were blocked or alternated by meaning (within subjects), followed by a free recall test completed immediately or after a 2.5-min delay. Correct recall was greater for blocked than for alternated lists. Critical-lure false recall was greater for blocked lists on an immediate test, whereas both list types produced equivalent false recall on a delayed test. In Experiment 2, lists blocked and alternated by meaning were presented via a between-subjects design, in order to eliminate possible list-type carryover effects. Correct recall replicated the result from Experiment 1; however, blocking lists increased false recall on delayed, but not on immediate, tests. Across the experiments, clustering correct recall by meaning increased across the delay selectively for the alternated lists. Our results suggest that thematic (i.e., gist) processes are influential for false recall, especially following a delay, a pattern consistent with fuzzy-trace theory. PMID:26105976

Thermal Vacuum Test of GLAS Propylene Loop Heat Pipe Development Model

NASA Technical Reports Server (NTRS)

Baker, Charles; Butler, Dan; Ku, Jentung; Kaya, Tarik; Nikitkin, Michael

2000-01-01

This paper presents viewgraphs on Thermal Vacuum Tests of the GLAS (Geoscience Laser Altimeter System) Propylene Loop Heat Pipe Development Model. The topics include: 1) Flight LHP System (Laser); 2) Test Design and Objectives; 3) DM (Development Model) LHP (Loop Heat Pipe) Test Design; 4) Starter Heater and Coupling Blocks; 5) CC Control Heaters and PRT; 6) Heater Plates (Shown in Reflux Mode); 7) Startup Tests; 8) CC Control Heater Power Tests for CC Temperature Control; and 9) Control Temperature Stability.

Testing of a Stitched Composite Large-Scale Multi-Bay Pressure Box

NASA Technical Reports Server (NTRS)

Jegley, Dawn; Rouse, Marshall; Przekop, Adam; Lovejoy, Andrew

2016-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to develop technologies to reduce aviation's impact on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe to enable the introduction of unconventional aircraft configurations. NASA and The Boeing Company have worked together to develop a structural concept that is lightweight and an advancement beyond state-of-the-art composite structures. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is an integrally stiffened panel design where elements are stitched together. The PRSEUS concept is designed to maintain residual load carrying capabilities under a variety of damage scenarios. A series of building block tests were evaluated to explore the fundamental assumptions related to the capability and advantages of PRSEUS panels. The final step in the building block series is an 80%-scale pressure box representing a portion of the center section of a Hybrid Wing Body (HWB) transport aircraft. The testing of this article under maneuver load and internal pressure load conditions is the subject of this paper. The experimental evaluation of this article, along with the other building block tests and the accompanying analyses, has demonstrated the viability of a PRSEUS center body for the HWB vehicle. Additionally, much of the development effort is also applicable to traditional tube-and-wing aircraft, advanced aircraft configurations, and other structures where weight and through-the-thickness strength are design considerations.

Synthetic aperture radar signal data compression using block adaptive quantization

NASA Technical Reports Server (NTRS)

Kuduvalli, Gopinath; Dutkiewicz, Melanie; Cumming, Ian

1994-01-01

This paper describes the design and testing of an on-board SAR signal data compression algorithm for ESA's ENVISAT satellite. The Block Adaptive Quantization (BAQ) algorithm was selected, and optimized for the various operational modes of the ASAR instrument. A flexible BAQ scheme was developed which allows a selection of compression ratio/image quality trade-offs. Test results show the high quality of the SAR images processed from the reconstructed signal data, and the feasibility of on-board implementation using a single ASIC.

Effect of High Speed Sintering on the Properties of Zirconia Oxide Materials

DTIC Science & Technology

2018-03-22

Beam-shaped specimens were designed using an Omnicam (Version 4.4.4; Dentsply Sirona) and milled from CAD/CAM blocks using a MCXL milling unit...8217. . . . . ··~· . IPS e.maxCAD CAD/CAM: block with milled beam RESUE.TS No significant differences were found for any of the properties tested between the

Cool in the Kitchen: Radiation, Conduction, and the Newton "Hot Block" Experiment.

ERIC Educational Resources Information Center

Silverman, Mark P.; Silverman, Christopher R.

2000-01-01

Discusses the history of the development of Newton's Law of Cooling. Describes an experiment conducted in the kitchen that is designed to test the rate of cooling of a hot block of iron. Finds that Newton's law does not represent very well the mechanism of heat loss. (Contains over 10 references.) (WRM)

14 CFR 33.95 - Engine-propeller systems tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine-propeller systems tests. 33.95... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.95 Engine-propeller systems tests. If the engine is designed to operate with a propeller, the following tests must be made with a...

14 CFR 33.95 - Engine-propeller systems tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Engine-propeller systems tests. 33.95... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.95 Engine-propeller systems tests. If the engine is designed to operate with a propeller, the following tests must be made with a...

14 CFR 33.95 - Engine-propeller systems tests.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Engine-propeller systems tests. 33.95... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.95 Engine-propeller systems tests. If the engine is designed to operate with a propeller, the following tests must be made with a...

14 CFR 33.95 - Engine-propeller systems tests.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Engine-propeller systems tests. 33.95... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.95 Engine-propeller systems tests. If the engine is designed to operate with a propeller, the following tests must be made with a...

14 CFR 33.95 - Engine-propeller systems tests.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Engine-propeller systems tests. 33.95... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.95 Engine-propeller systems tests. If the engine is designed to operate with a propeller, the following tests must be made with a...

REACT: Resettable Hold Down and Release Actuator for Space Applications

NASA Astrophysics Data System (ADS)

Nava, Nestor; Collado, Marcelo; Cabás, Ramiro

2014-07-01

A new HDRA based on SMA technology, called REACT, has been designed for development of loads and appendixes in space applications. This design involves a rod supported by spheres that block its axial movement during a preload application. The rod shape allows misalignment and blocks the rotation around axial axis for a proper installation of the device. Because of the high preload requirements for this type of actuators, finite element analysis (FEA) has been developed in order to check the structure resistance. The results of the FEA have constrained the REACT design, in terms of dimensions, materials, and shape of the mechanical parts. A complete test campaign for qualification of REACT is proposed. Several qualification models are intended to be built for testing in parallel. Therefore, it is a way to demonstrate margins which allows getting some statistics.

Comparative study of CAVET with dielectric and p-GaN gate and Mg ion-implanted current blocking layer

NASA Astrophysics Data System (ADS)

Mandal, Saptarshi; Agarwal, Anchal; Ahmadi, Elaheh; Mahadeva Bhat, K.; Laurent, Matthew A.; Keller, Stacia; Chowdhury, Srabanti

2017-08-01

In this work, a study of two different types of current aperture vertical electron transistor (CAVET) with ion-implanted blocking layer are presented. The device fabrication and performance limitation of a CAVET with a dielectric gate is discussed, and the breakdown limiting structure is evaluated using on-wafer test structures. The gate dielectric limited the device breakdown to 50V, while the blocking layer was able to withstand over 400V. To improve the device performance, an alternative CAVET structure with a p-GaN gate instead of dielectric is designed and realized. The pGaN gated CAVET structure increased the breakdown voltage to over 400V. Measurement of test structures on the wafer showed the breakdown was limited by the blocking layer instead of the gate p-n junction.

Blocking Filters with Enhanced Throughput for X-Ray Microcalorimetry

NASA Technical Reports Server (NTRS)

Grove, David; Betcher, Jacob; Hagen, Mark

2012-01-01

New and improved blocking filters (see figure) have been developed for microcalorimeters on several mission payloads, made of high-transmission polyimide support mesh, that can replace the nickel mesh used in previous blocking filter flight designs. To realize the resolution and signal sensitivity of today s x-ray microcalorimeters, significant improvements in the blocking filter stack are needed. Using high-transmission polyimide support mesh, it is possible to improve overall throughput on a typical microcalorimeter such as Suzaku s X-ray Spectrometer by 11%, compared to previous flight designs. Using polyimide to replace standard metal mesh means the mesh will be transparent to energies 3 keV and higher. Incorporating polyimide s advantageous strength-to-weight ratio, thermal stability, and transmission characteristics permits thinner filter materials, significantly enhancing through - put. A prototype contamination blocking filter for ASTRO-H has passed QT-level acoustic testing. Resistive traces can also be incorporated to provide decontamination capability to actively restore filter performance in orbit.

Inter-rater agreement among orthodontists in a blocked experiment.

PubMed

Korn, E L; Baumrind, S

1985-01-01

Five orthodontists were asked to predict for 64 patients a particular dichotomous outcome of treatment based on pre-treatment X-ray films. The orthodontists rated the cases in blocks of size 4-6 with the knowledge of the number of positive outcomes in each block. We discuss the reasons why this blocked design is appropriate whenever clinicians are asked to rate cases which have not been randomly selected from a clinical practice similar to their own. We give a simple description of the inter-rater agreement for this type of blocked experiment as well as a procedure to test that the agreement is no better than that expected by random independent assignment.

14 CFR 33.89 - Operation test.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., acceleration, overspeeding, ignition, functioning of the propeller (if the engine is designated to operate with a propeller); (2) Compliance with the engine response requirements of § 33.73; and (3) The minimum... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.89 Operation test. (a) The operation...

14 CFR 33.89 - Operation test.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., acceleration, overspeeding, ignition, functioning of the propeller (if the engine is designated to operate with a propeller); (2) Compliance with the engine response requirements of § 33.73; and (3) The minimum... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.89 Operation test. (a) The operation...

NASA's Space Launch System Program Update

NASA Technical Reports Server (NTRS)

May, Todd; Lyles, Garry

2015-01-01

Hardware and software for the world's most powerful launch vehicle for exploration is being welded, assembled, and tested today in high bays, clean rooms and test stands across the United States. NASA's Space Launch System (SLS) continued to make significant progress in the past year, including firing tests of both main propulsion elements, manufacturing of flight hardware, and the program Critical Design Review (CDR). Developed with the goals of safety, affordability, and sustainability, SLS will deliver unmatched capability for human and robotic exploration. The initial Block 1 configuration will deliver more than 70 metric tons (t) (154,000 pounds) of payload to low Earth orbit (LEO). The evolved Block 2 design will deliver some 130 t (286,000 pounds) to LEO. Both designs offer enormous opportunity and flexibility for larger payloads, simplifying payload design as well as ground and on-orbit operations, shortening interplanetary transit times, and decreasing overall mission risk. Over the past year, every vehicle element has manufactured or tested hardware, including flight hardware for Exploration Mission 1 (EM-1). This paper will provide an overview of the progress made over the past year and provide a glimpse of upcoming milestones on the way to a 2018 launch readiness date.

Liquid cooling applications on automotive exterior LED lighting

NASA Astrophysics Data System (ADS)

Aktaş, Mehmet; Şenyüz, Tunç; Şenyıldız, Teoman; Kılıç, Muhsin

2018-02-01

In this study cooling of a LED unit with heatsink and liquid cooling block which is used in automotive head lamp applications has been investigated numerically and experimentally. Junction temperature of a LED which is cooled with heatsink and liquid cooling block obtained in the experiment. 23°C is used both in the simulation and the experiment phase. Liquid cooling block material is choosed aluminium (Al) and polyamide. All tests and simulation are performed with three different flow rate. Temperature distribution of the designed product is investigated by doing the numerical simulations with a commercially software. In the simulations, fluid flow is assumed to be steady, incompressible and laminar and 3 dimensional (3D) Navier-Stokes equations are used. According to the calculations it is obtained that junction temperature is higher in the heatsink design compared to block cooled one. By changing the block material, it is desired to investigate the variation on the LED junction temperature. It is found that more efficient cooling can be obtained in block cooling by using less volume and weight. With block cooling lifetime of LED can be increased and flux loss can be decreased with the result of decreased junction temperature.

Software Design Document SAF Simulation Host CSCI (8). Volume 1, Sections 1.0 - 2.7

DTIC Science & Technology

1991-06-01

list for the patch, testing edges matching grid-loc-woni for intervisibility blocks. Calls Function IWhere Described Icheck edges Sec. 2.6.7.1.8 Table...edges matching grid-loc-word for intervisibility blocks. Calls Function Where Described check box Sec. 2.6.7.1.31 treelines Sec. 2.6.7.1.16 Icheck edges

Shear bond strength of computer-aided design and computer-aided manufacturing feldspathic and nano resin ceramics blocks cemented with three different generations of resin cement.

PubMed

Ab-Ghani, Zuryati; Jaafar, Wahyuni; Foo, Siew Fon; Ariffin, Zaihan; Mohamad, Dasmawati

2015-01-01

To evaluate the shear bond strength between the dentin substrate and computer-aided design and computer-aided manufacturing feldspathic ceramic and nano resin ceramics blocks cemented with resin cement. Sixty cuboidal blocks (5 mm × 5 mm × 5 mm) were fabricated in equal numbers from feldspathic ceramic CEREC(®) Blocs PC and nano resin ceramic Lava™ Ultimate, and randomly divided into six groups (n = 10). Each block was cemented to the dentin of 60 extracted human premolar using Variolink(®) II/Syntac Classic (multi-steps etch-and-rinse adhesive bonding), NX3 Nexus(®) (two-steps etch-and-rinse adhesive bonding) and RelyX™ U200 self-adhesive cement. All specimens were thermocycled, and shear bond strength testing was done using the universal testing machine at a crosshead speed of 1.0 mm/min. Data were analyzed using one-way ANOVA. Combination of CEREC(®) Blocs PC and Variolink(®) II showed the highest mean shear bond strength (8.71 Mpa), while the lowest of 2.06 Mpa were observed in Lava™ Ultimate and RelyX™ U200. There was no significant difference in the mean shear bond strength between different blocks. Variolink(®) II cement using multi-steps etch-and-rinse adhesive bonding provided a higher shear bond strength than the self-adhesive cement RelyX U200. The shear bond strength was not affected by the type of blocks used.

A new testing station about full-scale testing for rockfall protection systems

NASA Astrophysics Data System (ADS)

Bost, Marion; Dubois, Laurent; Rocher-Lacoste, Frédéric

2010-05-01

Rock blocks which detach from slopes overhanging urban areas, roads, railways and other infrastructures create one of the most frequent hazards in mountainous areas. Some of protection systems against rockfalls are designed to mitigate the effects of a foreseen movement by intercepting and stopping falling rock blocks. Despite the worldwide application of this kind of protections, the global behaviour of such a system has been poorly investigated, for the time being, and only at a reduced scale. The behaviour of these protection systems at real scale has been widely extrapolated, however these theories have still not been investigated by performing relating test at scale 1. The French Public Work Laboratory (LCPC) has decided to build a new testing station to work on that topic. This new testing station located in French Alps is able to drop heavy loads (up to 20 tons) from the top of a cliff down to structural systems in order to test their resistance to big shocks and study their dynamical behaviour at this high energy level. As the fall height can reach near 70m, the impact velocity can actually reach 35 metres per second and the energy released during the impact can be as large as 13 500 kilojoules. The experimental area at the bottom of the cliff which can be impacted by a block is 12 metres wide. This allows to test not only rockfall protection systems at scale 1 but also some parts of building structures too. To avoid damaging test-structure during a block drop due to dynamical effects, the dropping hook was designed with a special system. This one consists of a reversed mass which can be adapted to the dropped block and dropped together with the block. Moreover, it is very important to pay attention on repeatability of results concerning new devices for experiments. Whatever fall height the impact point is hit so with a precision of 50 centimetres. Such an experimental facility needs to be equipped with a relevant instrumentation. High capacity stress sensors, accelerometers and high speed cameras are available for experiments. They have been chosen for their capacity to work with an important length of cables. The monitoring with these experimental devices is performed at a high sample frequency suitable and for a very short load like an impact. A radio controlled system allows triggering monitoring and dropping at the same time. Due to bounce risk with the dropped block the safety of personal is ensured by strict operating rules. An observation platform has been located on an embankment along the test-site in order to follow experiments without risk. Two years were necessary for the test-site construction and its equipment. First tests on rockfall nets fences were performed at the end of 2009.

Qualification and Certification of 3D Printed Parts for Naval Ships

DTIC Science & Technology

2017-12-01

advances in computer systems, power generators, missile capabilities and product construction, yet they rarely change how something is created, designed or...settings), but section 1.3 takes a look at what must be determined during the design process to ensure the best product can be created. As seen in Chapter...center as well as the printed products . 46 Figure 33. Test Block Design All test cubes were immediately labeled upon being removed from the

The Behavior of a Stitched Composite Large-Scale Multi-Bay Pressure Box

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.; Rouse, Marshall; Przekop, Adam; Lovejoy, Andrew E.

2016-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to develop technologies to reduce impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe to enable the introduction of unconventional aircraft configurations. NASA and The Boeing Company have worked together to develop a structural concept that is lightweight and an advancement beyond state-of-the-art composite structures. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is an integrally stiffened panel design where elements are stitched together and designed to maintain residual load-carrying capabilities under a variety of damage scenarios. With the PRSEUS concept, through-the-thickness stitches are applied through dry fabric prior to resin infusion, and replace fasteners throughout each integral panel. Through-the-thickness reinforcement at discontinuities, such as along flange edges, has been shown to suppress delamination and turn cracks, which expands the design space and leads to lighter designs. The pultruded rod provides stiffening away from the more vulnerable skin surface and improves bending stiffness. A series of building block tests were evaluated to explore the fundamental assumptions related to the capability and advantages of PRSEUS panels. The final step in the building block series of tests is an 80%-scale pressure box representing a portion of the center section of a Hybrid Wing Body (HWB) transport aircraft. The testing of this test article under maneuver and internal pressure loading conditions is the subject of this paper. The experimental evaluation of this article, along with the other building block tests and the accompanying analyses, has demonstrated the viability of a PRSEUS center body for the HWB vehicle. Additionally, much of the development effort is also applicable to traditional tube-and-wing aircraft, advanced aircraft configurations, and other structures where weight and through-the-thickness strength are design considerations.

30MM GAU-8/A Plastic Frangible Projectile

DTIC Science & Technology

1977-03-01

20. ABSTRACT fContlnuo on rmvert» tld» 11 nacaaaary and Idontlly by block numbmr) ■feA 30mm target practice (TP) projectile, designed to break...contract to solve these problems. As a result, the Air Force has decided to delay further development of this projectile design concept...Section Title I INTRODUCTION II TECHNICAL DISCUSSION Design Parameters Final Projectile Design Design Evolution Acceptance Testing III

30 CFR 7.46 - Impact test.

Code of Federal Regulations, 2012 CFR

2012-07-01

... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Battery Assemblies § 7.46 Impact test. (a) Test... at 122 °F (50 °C) for a period of 48 hours. (2) Mount the covers on a battery box of the same design with which the covers are to be approved, including any support blocks, with the battery cells...

Experimental Investigations on Axially and Eccentrically Loaded Masonry Walls

NASA Astrophysics Data System (ADS)

Keshava, Mangala; Raghunath, Seshagiri Rao

2017-12-01

In India, un-reinforced masonry walls are often used as main structural components in load bearing structures. Indian code on masonry accounts the reduction in strength of walls by using stress reduction factors in its design philosophy. This code was introduced in 1987 and reaffirmed in 1995. The present study investigates the use of these factors for south Indian masonry. Also, with the gaining popularity in block work construction, the aim of this study was to find out the suitability of these factors given in the Indian code to block work masonry. Normally, the load carrying capacity of masonry walls can be assessed in three ways, namely, (1) tests on masonry constituents, (2) tests on masonry prisms and (3) tests on full-scale wall specimens. Tests on bricks/blocks, cement-sand mortar, brick/block masonry prisms and 14 full-scale brick/block masonry walls formed the experimental investigation. The behavior of the walls was investigated under varying slenderness and eccentricity ratios. Hollow concrete blocks normally used as in-fill masonry can be considered as load bearing elements as its load carrying capacity was found to be high when compared to conventional brick masonry. Higher slenderness and eccentricity ratios drastically reduced the strength capacity of south Indian brick masonry walls. The reduction in strength due to slenderness and eccentricity is presented in the form of stress reduction factors in the Indian code. These factors obtained through experiments on eccentrically loaded brick masonry walls was lower while that of brick/block masonry under axial loads was higher than the values indicated in the Indian code. Also the reduction in strength is different for brick and block work masonry thus indicating the need for separate stress reduction factors for these two masonry materials.

Universal Verification Methodology Based Register Test Automation Flow.

PubMed

Woo, Jae Hun; Cho, Yong Kwan; Park, Sun Kyu

2016-05-01

In today's SoC design, the number of registers has been increased along with complexity of hardware blocks. Register validation is a time-consuming and error-pron task. Therefore, we need an efficient way to perform verification with less effort in shorter time. In this work, we suggest register test automation flow based UVM (Universal Verification Methodology). UVM provides a standard methodology, called a register model, to facilitate stimulus generation and functional checking of registers. However, it is not easy for designers to create register models for their functional blocks or integrate models in test-bench environment because it requires knowledge of SystemVerilog and UVM libraries. For the creation of register models, many commercial tools support a register model generation from register specification described in IP-XACT, but it is time-consuming to describe register specification in IP-XACT format. For easy creation of register model, we propose spreadsheet-based register template which is translated to IP-XACT description, from which register models can be easily generated using commercial tools. On the other hand, we also automate all the steps involved integrating test-bench and generating test-cases, so that designers may use register model without detailed knowledge of UVM or SystemVerilog. This automation flow involves generating and connecting test-bench components (e.g., driver, checker, bus adaptor, etc.) and writing test sequence for each type of register test-case. With the proposed flow, designers can save considerable amount of time to verify functionality of registers.

Split-Block Waveguide Polarization Twist for 220 to 325 GHz

NASA Technical Reports Server (NTRS)

Ward, John; Chattopadhyay, Goutam

2008-01-01

A split-block waveguide circuit that rotates polarization by 90 has been designed with WR-3 input and output waveguides, which are rectangular waveguides used for a nominal frequency range of 220 to 325 GHz. Heretofore, twisted rectangular waveguides equipped with flanges at the input and output have been the standard means of rotating the polarizations of guided microwave signals. However, the fabrication and assembly of such components become difficult at high frequency due to decreasing wavelength, such that twisted rectangular waveguides become impractical at frequencies above a few hundred gigahertz. Conventional twisted rectangular waveguides are also not amenable to integration into highly miniaturized subassemblies of advanced millimeter- and submillimeter-wave detector arrays now undergoing development. In contrast, the present polarization- rotating waveguide can readily be incorporated into complex integrated waveguide circuits such as miniaturized detector arrays fabricated by either conventional end milling of metal blocks or by deep reactive ion etching of silicon blocks. Moreover, the present split-block design can be scaled up in frequency to at least 5 THz. The main step in fabricating a splitblock polarization-rotating waveguide of the present design is to cut channels having special asymmetrically shaped steps into mating upper and lower blocks (see Figure 1). The dimensions of the steps are chosen to be consistent with the WR-3 waveguide cross section, which is 0.864 by 0.432 mm. The channels are characterized by varying widths with constant depths of 0.432, 0.324, and 0.216 mm and by relatively large corner radii to facilitate fabrication. The steps effect both a geometric transition and the corresponding impedance-matched electromagnetic-polarization transition between (1) a WR-3 rectangular waveguide oriented with the electric field vector normal to the block mating surfaces and (2) a corresponding WR-3 waveguide oriented with its electric field vector parallel to the mating surfaces of the blocks. A prototype has been built and tested. Figure 2 presents test results indicative of good performance over nearly the entire WR-3 waveguide frequency band.

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2011 CFR

2011-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2010 CFR

2010-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2012 CFR

2012-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2014 CFR

2014-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2013 CFR

2013-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

Broader autism phenotype in parents of autistic children: reality or myth?

PubMed

Scheeren, Anke M; Stauder, Johannes E A

2008-02-01

The finding that relatives of individuals with autism show mild autistic traits is referred to as the broader autism phenotype (BAP). In the current study, 25 parents with a child with high-functioning autism and 25 parents with typically developed children were compared on: (1) the Block Design Test, (2) the Autism-Spectrum Quotient (AQ), and (3) a reaction time task to examine reflexive covert visual orienting to social (eyes) and non-social (arrows) cues. The parent groups were scored similar on the Block Design Test and the AQ. However, fathers with an autistic child demonstrated a different reaction time pattern and responded slower on the social cues than control fathers. These results partly support and further elaborate on the BAP in parents with an autistic child.

Structural Element Testing in Support of the Design of the NASA Composite Crew Module

NASA Technical Reports Server (NTRS)

Kellas, Sotiris; Jackson, Wade C.; Thesken, John C.; Schleicher, Eric; Wagner, Perry; Kirsch, Michael T.

2012-01-01

In January 2007, the NASA Administrator and Associate Administrator for the Exploration Systems Mission Directorate chartered the NASA Engineering and Safety Center (NESC) to design, build, and test a full-scale Composite Crew Module (CCM). For the design and manufacturing of the CCM, the team adopted the building block approach where design and manufacturing risks were mitigated through manufacturing trials and structural testing at various levels of complexity. Following NASA's Structural Design Verification Requirements, a further objective was the verification of design analysis methods and the provision of design data for critical structural features. Test articles increasing in complexity from basic material characterization coupons through structural feature elements and large structural components, to full-scale structures were evaluated. This paper discusses only four elements tests three of which include joints and one that includes a tapering honeycomb core detail. For each test series included are specimen details, instrumentation, test results, a brief analysis description, test analysis correlation and conclusions.

Clinical trial uses combination therapy for certain types of non-Hodgkin lymphoma | Center for Cancer Research

Cancer.gov

Researchers are testing the safety of the combination of an experimental drug with rituximab, a standard treatment, for patients with indolent or diffuse large B-cell lymphoma. The antibody is designed to target and block a protein that is present on cancer cells and is used by those cells to protect themselves from your body’s immune system. Blocking the protein may enable

Comparison of the effects block and traditional schedules have on the number of students who are proficient on the Biology End-of-Course Test in forty public high schools in the state of North Carolina

NASA Astrophysics Data System (ADS)

Bonner, Tonia Anita

This study examined the difference between the number of overall students, African-American students, and students with disabilities on a semester 4 x 4 block schedule who were proficient on the North Carolina Biology End-of-Course Test and the number of the same group of students on a traditional 45-50 minute yearlong schedule who were proficient on the NC Biology End-of-Course Test in the state of North Carolina during the 2009--2010 school year. A causal-comparative design was used and three null hypotheses were tested using chi-square analysis. Archival data was used. The results showed that there was a significant association between the number of the overall students and African-American students who were proficient on the NC Biology EOC Test when taught biology on a 4 x 4 semester block versus a traditional schedule. However, no statistically significant relationship existed between the number of students with disabilities who were educated on 4 x 4 semester block schedule and those students with disabilities who were educated on a six or seven period traditional schedule in biology. Suggestions for further research are included.

Optimization of Blocked Designs in fMRI Studies

ERIC Educational Resources Information Center

Maus, Barbel; van Breukelen, Gerard J. P.; Goebel, Rainer; Berger, Martijn P. F.

2010-01-01

Blocked designs in functional magnetic resonance imaging (fMRI) are useful to localize functional brain areas. A blocked design consists of different blocks of trials of the same stimulus type and is characterized by three factors: the length of blocks, i.e., number of trials per blocks, the ordering of task and rest blocks, and the time between…

Two injection digital block versus single subcutaneous palmar injection block for finger lacerations.

PubMed

Okur, O M; Şener, A; Kavakli, H Ş; Çelik, G K; Doğan, N Ö; Içme, F; Günaydin, G P

2017-12-01

We aimed to compare two digital nerve block techniques in patients due to traumatic digital lacerations. This was a randomized-controlled study designed prospectively in the emergency department of a university-based training and research hospital. Randomization was achieved by sealed envelopes. Half of the patients were randomised to traditional (two-injection) digital nerve block technique while single-injection digital nerve block technique was applied to the other half. Score of pain due to anesthetic infiltration and suturing, onset time of total anesthesia, need for an additional rescue injection were the parameters evaluated with both groups. Epinephrin added lidocaine hydrochloride preparation was used for the anesthetic application. Visual analog scale was used for the evaluation of pain scores. Outcomes were compared by using Mann-Whitney U test and Student t-test. Fifty emergency department patients ≥18 years requiring digital nerve block were enrolled in the study. Mean age of the patients was 33 (min-max: 19-86) and 39 (78 %) were male. No statistically significant difference was found between the two groups in terms of our main parameters; anesthesia pain score, suturing pain score, onset time of total anesthesia and rescue injection need. Single injection volar digital nerve block technique is a suitable alternative for digital anesthesias in emergency departments.

Redesigning Design: Field Testing a Revised Design Rubric Based on iNACOL Quality Course Standards

ERIC Educational Resources Information Center

Adelstein, David; Barbour, Michael K.

2016-01-01

Designers have a limited selection of K-12 online course creation standards to choose from that are not blocked behind proprietary or pay walls. For numerous institutions and states, the use of the iNACOL "National Standards for Quality Online Courses" is becoming a widely used resource. This article presents the final phase in a…

Assessing the associative deficit of older adults in long-term and short-term/working memory.

PubMed

Chen, Tina; Naveh-Benjamin, Moshe

2012-09-01

Older adults exhibit a deficit in associative long-term memory relative to younger adults. However, the literature is inconclusive regarding whether this deficit is attenuated in short-term/working memory. To elucidate the issue, three experiments assessed younger and older adults' item and interitem associative memory and the effects of several variables that might potentially contribute to the inconsistent pattern of results in previous studies. In Experiment 1, participants were tested on item and associative recognition memory with both long-term and short-term retention intervals in a single, continuous recognition paradigm. There was an associative deficit for older adults in the short-term and long-term intervals. Using only short-term intervals, Experiment 2 utilized mixed and blocked test designs to examine the effect of test event salience. Blocking the test did not attenuate the age-related associative deficit seen in the mixed test blocks. Finally, an age-related associative deficit was found in Experiment 3, under both sequential and simultaneous presentation conditions. Even while accounting for some methodological issues, the associative deficit of older adults is evident in short-term/working memory.

Experimental and Analytical Evaluation of a Composite Honeycomb Deployable Energy Absorber

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Kellas, Sotiris; Horta, Lucas G.; Annett, Martin S.; Polanco, Michael A.; Littell, Justin D.; Fasanella, Edwin L.

2011-01-01

In 2006, the NASA Subsonic Rotary Wing Aeronautics Program sponsored the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, which is designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar honeycomb structure to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed flat until needed for deployment. A variety of deployment options such as linear, radial, and/or hybrid methods can be used. Experimental evaluation of the DEA utilized a building block approach that included material characterization testing of its constituent, Kevlar -129 fabric/epoxy, and flexural testing of single hexagonal cells. In addition, the energy attenuation capabilities of the DEA were demonstrated through multi-cell component dynamic crush tests, and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto concrete, water, and soft soil. During each stage of the DEA evaluation process, finite element models of the test articles were developed and simulations were performed using the explicit, nonlinear transient dynamic finite element code, LS-DYNA. This report documents the results of the experimental evaluation that was conducted to assess the energy absorption capabilities of the DEA.

Comparative Microstrain Study of Internal Hexagon and Plateau Design of Short Implants Under Vertical Loading.

PubMed

Nishioka, Renato Sussumu; Rodrigues, Vinicius Anéas; De Santis, Leandro Ruivo; Nishioka, Gabriela Nogueira De Melo; Santos, Vivian Mayumi Miyazaki; Souza, Francisley Ávila

2016-02-01

To quantify microstrain development during axial loading using strain gauge analysis for short implants, varying the type of fixture-abutment joint and thread design. An internal hexagon implant (4 × 8 mm) and a plateau design implant (4 × 8 mm) were embedded on the center of 10 polyurethane blocks with dimensions of 190 × 30 × 12 mm. The respective abutments were screwed onto the implants. Four strain gauges (SGs) were bonded onto the surface of each block, and 4 vertical SGs were bonded onto the side of each block. Axial load of 30 kgf was applied for 10 seconds in the center of each implant. The data were analyzed statistically by analysis of variance for repeated measures and Tukey test (P < 0.05). The interaction between implant and region factors have been statistically significant (P = 0.0259). Tukey test revealed a difference on plateau's horizontal region. The cervical region presented higher microstrain values, when compared with the medium and apical regions of the implants. Within the purpose of the study, the type of fixture-abutment joint is a relevant factor to affect the amount of stress/strain in bone simulation. The microstrain development was concentrated on the cervical region of the implant.

Testing block subdivision algorithms on block designs

NASA Astrophysics Data System (ADS)

Wiseman, Natalie; Patterson, Zachary

2016-01-01

Integrated land use-transportation models predict future transportation demand taking into account how households and firms arrange themselves partly as a function of the transportation system. Recent integrated models require parcels as inputs and produce household and employment predictions at the parcel scale. Block subdivision algorithms automatically generate parcel patterns within blocks. Evaluating block subdivision algorithms is done by way of generating parcels and comparing them to those in a parcel database. Three block subdivision algorithms are evaluated on how closely they reproduce parcels of different block types found in a parcel database from Montreal, Canada. While the authors who developed each of the algorithms have evaluated them, they have used their own metrics and block types to evaluate their own algorithms. This makes it difficult to compare their strengths and weaknesses. The contribution of this paper is in resolving this difficulty with the aim of finding a better algorithm suited to subdividing each block type. The proposed hypothesis is that given the different approaches that block subdivision algorithms take, it's likely that different algorithms are better adapted to subdividing different block types. To test this, a standardized block type classification is used that consists of mutually exclusive and comprehensive categories. A statistical method is used for finding a better algorithm and the probability it will perform well for a given block type. Results suggest the oriented bounding box algorithm performs better for warped non-uniform sites, as well as gridiron and fragmented uniform sites. It also produces more similar parcel areas and widths. The Generalized Parcel Divider 1 algorithm performs better for gridiron non-uniform sites. The Straight Skeleton algorithm performs better for loop and lollipop networks as well as fragmented non-uniform and warped uniform sites. It also produces more similar parcel shapes and patterns.

Materials and Process Activities for NASA's Composite Crew Module

NASA Technical Reports Server (NTRS)

Polis, Daniel L.

2012-01-01

In January 2007, the NASA Administrator and Associate Administrator for the Exploration Systems Mission Directorate chartered the NASA Engineering and Safety Center (NESC) to design, build, and test a full-scale Composite Crew Module (CCM). The overall goal of the CCM project was to develop a team from the NASA family with hands-on experience in composite design, manufacturing, and testing in anticipation of future space exploration systems being made of composite materials. The CCM project was planned to run concurrently with the Orion project s baseline metallic design within the Constellation Program so that features could be compared and discussed without inducing risk to the overall Program. The materials and process activities were prioritized based on a rapid prototype approach. This approach focused developmental activities on design details with greater risk and uncertainty, such as out-of-autoclave joining, over some of the more traditional lamina and laminate building block levels. While process development and associated building block testing were performed, several anomalies were still observed at the full-scale level due to interactions between process robustness and manufacturing scale-up. This paper describes the process anomalies that were encountered during the CCM development and the subsequent root cause investigations that led to the final design solutions. These investigations highlight the importance of full-scale developmental work early in the schedule of a complex composite design/build project.

Proceedings of the Workshop on Measurement and Analysis of Structural Response in Concrete Armor Units Held in Vicksburg, Mississippi on 23-24 January 1985

DTIC Science & Technology

1988-02-01

57 Summary--"Comments from Dr. Hans Burcharth" ............81 "Strength of Armour Blocks...335 APPENDICES........................................................ 387 A--"Strength of Concrete Armour Units for Breakwaters"’ --Delft...STAT!STICS DESIGN WAVE CLIMATE PRELIMINARY DESIGN CALCULATION OF ARMOUR STABILIY ETC MODEL TESTS OF PRELIMINARY DESIGN FINAL DESIGN Figure 1. Ideal

Current-mode subthreshold MOS implementation of the Herault-Jutten autoadaptive network

NASA Astrophysics Data System (ADS)

Cohen, Marc H.; Andreou, Andreas G.

1992-05-01

The translinear circuits in subthreshold MOS technology and current-mode design techniques for the implementation of neuromorphic analog network processing are investigated. The architecture, also known as the Herault-Jutten network, performs an independent component analysis and is essentially a continuous-time recursive linear adaptive filter. Analog I/O interface, weight coefficients, and adaptation blocks are all integrated on the chip. A small network with six neurons and 30 synapses was fabricated in a 2-microns n-well double-polysilicon, double-metal CMOS process. Circuit designs at the transistor level yield area-efficient implementations for neurons, synapses, and the adaptation blocks. The design methodology and constraints as well as test results from the fabricated chips are discussed.

The Power of the Test for Treatment Effects in Three-Level Block Randomized Designs

ERIC Educational Resources Information Center

Konstantopoulos, Spyros

2008-01-01

Experiments that involve nested structures may assign treatment conditions either to subgroups (such as classrooms) or individuals within subgroups (such as students). The design of such experiments requires knowledge of the intraclass correlation structure to compute the sample sizes necessary to achieve adequate power to detect the treatment…

SAMPA Chip: the New 32 Channels ASIC for the ALICE TPC and MCH Upgrades

NASA Astrophysics Data System (ADS)

Adolfsson, J.; Ayala Pabon, A.; Bregant, M.; Britton, C.; Brulin, G.; Carvalho, D.; Chambert, V.; Chinellato, D.; Espagnon, B.; Hernandez Herrera, H. D.; Ljubicic, T.; Mahmood, S. M.; Mjörnmark, U.; Moraes, D.; Munhoz, M. G.; Noël, G.; Oskarsson, A.; Osterman, L.; Pilyar, A.; Read, K.; Ruette, A.; Russo, P.; Sanches, B. C. S.; Severo, L.; Silvermyr, D.; Suire, C.; Tambave, G. J.; Tun-Lanoë, K. M. M.; van Noije, W.; Velure, A.; Vereschagin, S.; Wanlin, E.; Weber, T. O.; Zaporozhets, S.

2017-04-01

This paper presents the test results of the second prototype of SAMPA, the ASIC designed for the upgrade of read-out front end electronics of the ALICE Time Projection Chamber (TPC) and Muon Chamber (MCH). SAMPA is made in a 130 nm CMOS technology with 1.25 V nominal voltage supply and provides 32 channels, with selectable input polarity, and three possible combinations of shaping time and sensitivity. Each channel consists of a Charge Sensitive Amplifier, a semi-Gaussian shaper and a 10-bit ADC; a Digital Signal Processor provides digital filtering and compression capability. In the second prototype run both full chip and single test blocks were fabricated, allowing block characterization and full system behaviour studies. Experimental results are here presented showing agreement with requirements for both the blocks and the full chip.

An fMRI-study of locally oriented perception in autism: altered early visual processing of the block design test.

PubMed

Bölte, S; Hubl, D; Dierks, T; Holtmann, M; Poustka, F

2008-01-01

Autism has been associated with enhanced local processing on visual tasks. Originally, this was based on findings that individuals with autism exhibited peak performance on the block design test (BDT) from the Wechsler Intelligence Scales. In autism, the neurofunctional correlates of local bias on this test have not yet been established, although there is evidence of alterations in the early visual cortex. Functional MRI was used to analyze hemodynamic responses in the striate and extrastriate visual cortex during BDT performance and a color counting control task in subjects with autism compared to healthy controls. In autism, BDT processing was accompanied by low blood oxygenation level-dependent signal changes in the right ventral quadrant of V2. Findings indicate that, in autism, locally oriented processing of the BDT is associated with altered responses of angle and grating-selective neurons, that contribute to shape representation, figure-ground, and gestalt organization. The findings favor a low-level explanation of BDT performance in autism.

Assessment of the State-of-the-Art in the Design and Manufacturing of Large Composite Structure

NASA Technical Reports Server (NTRS)

Harris, C. E.

2001-01-01

This viewgraph presentation gives an assessment of the state-of-the-art in the design and manufacturing of large component structures, including details on the use of continuous fiber reinforced polymer matrix composites (CFRP) in commercial and military aircraft and in space launch vehicles. Project risk mitigation plans must include a building-block test approach to structural design development, manufacturing process scale-up development tests, and pre-flight ground tests to verify structural integrity. The potential benefits of composite structures justifies NASA's investment in developing the technology. Advanced composite structures technology is enabling to virtually every Aero-Space Technology Enterprise Goal.

Testing of selected metallic reinforcing bars for extending the service life of future concrete bridges : testing in outdoor concrete blocks.

DOT National Transportation Integrated Search

2002-01-01

To meet the challenge of a design life of 100 years for major concrete bridges, economical and corrosion-resistant reinforcing bars will be needed. The preliminary results for stainless steel-clad bars in a recent investigation funded by the Federal ...

31 CFR Appendix A to Chapter V - Alphabetical Listing of Blocked Persons, Blocked Vessels, Specially Designated Nationals...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Alphabetical Listing of Blocked Persons, Blocked Vessels, Specially Designated Nationals, Specially Designated Terrorists, Specially Designated Global Terrorists, Foreign Terrorist Organizations, and Specially Designated Narcotics Traffickers (as of May 13, 2010) A Appendix A to Chapte...

[Effects of temporal lobe epilepsy and idiopathic epilepsy on cognitive function and emotion in children].

PubMed

Yang, Xiao-Yan; Long, Li-Li; Xiao, Bo

2016-07-01

To investigate the effects of temporal lobe epilepsy and idiopathic epilepsy on cognitive function and emotion in children and the risk factors for cognitive impairment. A retrospective analysis was performed for the clinical data of 38 children with temporal lobe epilepsy and 40 children with idiopathic epilepsy. The controls were 42 healthy children. All subjects received the following neuropsychological tests: Montreal Cognitive Assessment (MoCA) scale, verbal fluency test, digit span test, block design test, Social Anxiety Scale for Children (SASC), and Depression Self-rating Scale for Children (DSRSC). Compared with the control group, the temporal lobe epilepsy and idiopathic epilepsy groups showed significantly lower scores of MoCA, verbal fluency, digit span, and block design (P<0.05) and significantly higher scores on SASC and DSRSC (P<0.05). Compared with the idiopathic epilepsy group, the temporal lobe epilepsy group showed significantly lower scores of MoCA, verbal fluency, digit span, and block design (P<0.05) and significantly higher scores on SASC and DSRSC (P<0.05). In the temporal lobe epilepsy group, MoCA score was negatively correlated with SASC score, DSRSC score, and seizure frequency (r=-0.571, -0.529, and -0.545 respectively; P<0.01). In the idiopathic epilepsy group, MoCA score was also negatively correlated with SASC score, DSRSC score, and seizure frequency (r=-0.542, -0.487, and -0.555 respectively; P<0.01). Children with temporal lobe epilepsy and idiopathic epilepsy show impaired whole cognition, verbal fluency, memory, and executive function and have anxiety and depression, which are more significant in children with temporal lobe epilepsy. High levels of anxiety, depression, and seizure frequency are risk factors for impaired cognitive function.

Comparison of periodontal ligament injection and inferior alveolar nerve block in mandibular primary molars pulpotomy: a randomized control trial.

PubMed

Haghgoo, Roza; Taleghani, Ferial

2015-05-01

Inferior alveolar nerve block is a common technique for anesthesia of the primary mandibular molars. A number of disadvantages have been shown to be associated with this technique. Periodontal ligament (PDL) injection could be considered as an alternative to inferior alveolar nerve block. The aim of this study was to evaluate the effectiveness of PDL injection in the anesthesia of primary molar pulpotomy with mandibular block. This study was performed using a sequential double-blind randomized trial design. 80 children aged 3-7 years old who required pulpotomy in symmetrical mandibular primary molars were selected. The teeth of these children were anesthetized with periodontal injection on one side of the mandible and block on the other. Pulpotomy was performed on each patient during the same appointment. Signs of discomfort, including hand and body tension and eye movement, the verbal complaint and crying (SEM scale), were evaluated by a dental assistant who was blinded to the treatment allocation of the patients. Finally, the data were analyzed using the exact Fisher test and Pearson Chi-squared exact test. Success rate was 88/75 and 91/25 in the PDL injection and nerve block groups, respectively. There was no statistically significant difference between the two techniques (P = 0.250). Results showed that PDL injection can be used as an alternative to nerve block in pulpotomy of the mandibular primary molars.

Effect of different adhesive strategies on microtensile bond strength of computer aided design/computer aided manufacturing blocks bonded to dentin.

PubMed

Roperto, Renato; Akkus, Anna; Akkus, Ozan; Lang, Lisa; Sousa-Neto, Manoel Damiao; Teich, Sorin; Porto, Thiago Soares

2016-01-01

The aim of this study was to determine the microtensile bond strength (μTBS) of ceramic and composite computer aided design-computer aided manufacturing (CAD-CAM) blocks bonded to dentin using different adhesive strategies. In this in vitro study, 30 crowns of sound freshly extracted human molars were sectioned horizontally 3 mm above the cementoenamel junction to produce flat dentin surfaces. Ceramic and composite CAD/CAM blocks, size 14, were sectioned into slices of 3 mm thick. Before bonding, CAD/CAM block surfaces were treated according to the manufacturer's instructions. Groups were created based on the adhesive strategy used: Group 1 (GI) - conventional resin cement + total-etch adhesive system, Group 2 (GII) - conventional resin cement + self-etch adhesive system, and Group 3 (GIII) - self-adhesive resin cement with no adhesive. Bonded specimens were stored in 100% humidity for 24h at 37΀C, and then sectioned with a slow-speed diamond saw to obtain 1 mm × 1 mm × 6 mm microsticks. Microtensile testing was then conducted using a microtensile tester. μTBS values were expressed in MPa and analyzed by one-way ANOVA with post hoc (Tukey) test at the 5% significance level. Mean values and standard deviations of μTBS (MPa) were 17.68 (±2.71) for GI/ceramic; 17.62 (±3.99) for GI/composite; 13.61 (±6.92) for GII/composite; 12.22 (±4.24) for GII/ceramic; 7.47 (±2.29) for GIII/composite; and 6.48 (±3.10) for GIII/ceramic; ANOVA indicated significant differences among the adhesive modality and block interaction (P < 0.05), and no significant differences among blocks only, except between GI and GII/ceramic. Bond strength of GIII was consistently lower (P < 0.05) than GI and GII groups, regardless the block used. Cementation of CAD/CAM restorations, either composite or ceramic, can be significantly affected by different adhesive strategies used.

A new device to test cutting efficiency of mechanical endodontic instruments.

PubMed

Giansiracusa Rubini, Alessio; Plotino, Gianluca; Al-Sudani, Dina; Grande, Nicola M; Sonnino, Gianpaolo; Putorti, Ermanno; Cotti, Elisabetta; Testarelli, Luca; Gambarini, Gianluca

2014-03-06

The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments. Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the "Reciproc ALL" program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P<0.05). Reciproc in reciprocation (Group 1) mean cut in the Plexiglas block was 8.6 mm (SD=0.6 mm), while Reciproc in rotation mean cut was 8.9 mm (SD=0.7 mm). There was no statistically significant difference between the 2 groups investigated (P>0.05). The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments.

24 CFR 3285.306 - Design procedures for concrete block piers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... block piers. 3285.306 Section 3285.306 Housing and Urban Development Regulations Relating to Housing and....306 Design procedures for concrete block piers. (a) Frame piers less than 36 inches high. (1) Frame... blocks, 8 inches “ 8 inches “ 16 inches, when the design capacity of the block is not exceeded. (2) The...

Non-neural BOLD variability in block and event-related paradigms.

PubMed

Kannurpatti, Sridhar S; Motes, Michael A; Rypma, Bart; Biswal, Bharat B

2011-01-01

Block and event-related stimulus designs are typically used in fMRI studies depending on the importance of detection power or estimation efficiency. The extent of vascular contribution to variability in block and event-related fMRI-BOLD response is not known. With scaling, the extent of vascular variability in the fMRI-BOLD response during block and event-related design tasks was investigated. Blood oxygen level-dependent (BOLD) contrast data from healthy volunteers performing a block design motor task and an event-related memory task requiring performance of a motor response were analyzed from the regions of interest (ROIs) surrounding the primary and supplementary motor cortices. Average BOLD signal change was significantly larger during the block design compared to the event-related design. In each subject, BOLD signal change across voxels in the ROIs had higher variation during the block design task compared to the event-related design task. Scaling using the resting state fluctuation of amplitude (RSFA) and breath-hold (BH), which minimizes BOLD variation due to vascular origins, reduced the within-subject BOLD variability in every subject during both tasks but significantly reduced BOLD variability across subjects only during the block design task. The strong non-neural source of intra- and intersubject variability of BOLD response during the block design compared to event-related task indicates that study designs optimizing for statistical power through enhancement of the BOLD contrast (for, e.g., block design) can be affected by enhancement of non-neural sources of BOLD variability. Copyright © 2011. Published by Elsevier Inc.

An Integrated 520-600 GHz Sub-Harmonic Mixer and Tripler Combination Based on GaAs MMIC Membrane Planar Schottky Diodes

NASA Technical Reports Server (NTRS)

Thomas, B.; Gill, J.; Maestrini, A.; Lee, C.; Lin, R.; Sin, S.; Peralta, A.; Mehdi, I.

2011-01-01

We present here the design, development and test of an integrated sub-millimeter front-end featuring a 520-600 GHz sub-harmonic mixer and a 260-300 GHz frequency tripler in a single cavity. Both devices used GaAs MMIC membrane planar Schottky diode technology. The sub-harmonic mixer/tripler circuit has been tested using conventional machined as well as silicon micro-machined blocks. Measurement results on the metal block give best DSB mixer noise temperature of 2360 K and conversion losses of 7.7 dB at 520 GHz. Preliminary results on the silicon micro-machined blocks give a DSB mixer noise temperature of 4860 K and conversion losses of 12.16 dB at 540 GHz. The LO input power required to pump the integrated tripler/sub-harmonic mixer for both packages is between 30 and 50 mW

An Integrated 520-600 GHz Sub-Harmonic Mixer and Tripler Combination Based on GaAs MMIC Membrane Planar Schottky Diodes

NASA Technical Reports Server (NTRS)

Thomas, B.; Gill, J.; Maestrini, A.; Lee, C.; Lin, R.; Sin, S.; Peralta, A.; Mehdi, I.

2010-01-01

We present here the design, development and test of an integrated sub-millimeter front-end featuring a 520-600 GHz sub-harmonic mixer and a 260-300 GHz frequency tripler in a single cavity. Both devices used GaAs MMIC membrane planar Schottky diode technology. The sub-harmonic mixer/tripler circuit has been tested using conventional machined as well as silicon micro-machined blocks. Measurement results on the metal block give best DSB mixer noise temperature of 2360 K and conversion losses of 7.7 dB at 520 GHz. Preliminary results on the silicon micro-machined blocks give a DSB mixer noise temperature of 4860 K and conversion losses of 12.16 dB at 540 GHz. The LO input power required to pump the integrated tripler/sub-harmonic mixer for both packages is between 30 and 50 mW.

Fusion And Inference From Multiple And Massive Disparate Distributed Dynamic Data Sets

DTIC Science & Technology

2017-07-01

principled methodology for two-sample graph testing; designed a provably almost-surely perfect vertex clustering algorithm for block model graphs; proved...3.7 Semi-Supervised Clustering Methodology ...................................................................... 9 3.8 Robust Hypothesis Testing...dimensional Euclidean space – allows the full arsenal of statistical and machine learning methodology for multivariate Euclidean data to be deployed for

4 out of 5 Students Surveyed Would Recommend this Activity (Comparing Chewing Gum Flavor Durations)

ERIC Educational Resources Information Center

Richardson, Mary; Rogness, Neal; Gajewski, Byron

2005-01-01

This paper describes an interactive activity developed for illustrating hypothesis tests on the mean for paired or matched samples. The activity is extended to illustrate assessing normality, the Wilcoxon signed rank test, Kaplan-Meier survival functions, two-way analysis of variance, and the randomized block design. (Contains 6 tables and 13…

Clinical trial uses combination therapy for certain types of non-Hodgkin lymphoma | Center for Cancer Research

Cancer.gov

Researchers are testing the safety of the combination of an experimental drug with rituximab, a standard treatment, for patients with indolent or diffuse large B-cell lymphoma. The antibody is designed to target and block a protein that is present on cancer cells and is used by those cells to protect themselves from your body’s immune system. Blocking the protein may enable your body’s immune system to find and destroy the cancer cells. Read more…

Design, Project Execution, and Commissioning of the 1.8 K Superfluid Helium Refrigeration System for SRF Cryomodule Testing

DOE PAGES

Treite, P.; Nuesslein, U.; Jia, Yi; ...

2015-07-15

The Fermilab Cryomodule Test Facility (CMTF) provides a test bed to measure the performance of superconducting radiofrequency (SRF) cryomodules (CM). These SRF components form the basic building blocks of future high intensity accelerators such as the International Linear Collider (ILC) and a Muon Collider. Linde Kryotechnik AG and Linde Cryogenics have designed, constructed and commissioned the superfluid helium refrigerator needed to support SRF component testing at the CMTF Facility. The hybrid refrigerator is designed to operate in a variety of modes and under a wide range of boundary conditions down to 1.8 Kelvin set by CM design. Special features ofmore » the refrigerator include the use of warm and cold compression and high efficiency turbo expanders.This paper gives an overview on the wide range of the challenging cooling requirements, the design, fabrication and the commissioning of the installed cryogenic system.« less

Characterization of a small Terfenol-D transducer in mechanically blocked configuration

NASA Astrophysics Data System (ADS)

Faidley, LeAnn E.; Dapino, Marcelo J.; Flatau, Alison B.

2001-08-01

In numerous applications, smart material transducers are employed to actuate upon virtually immovable structures, that is, structures whose stiffness approaches infinity in comparison with that of the transducer itself. Such mechanically blocked transducer configurations can be found in applications ranging from seismic testing and isolation of civil structures, to clamping mechanisms in linear or rotational inchworm motors. In addition to providing high blocking forces, smart materials for this type of applications must often be small in size and lightweight in order for design constraints to be met. This paper provides a characterization of the force produced by a 0.9 cm (0.35 in) diameter, 2.0 cm (0.79i in) long Terfenol-D operated under mechanically blocked conditions. Experimental results are shown for several mechanical preloads as well as various magnetic field intensities, waveforms, and frequencies. Optimal levels are deduced and discussed and the results are compared to published data for a PZT transducer of similar size operated in mechanically blocked configuration. The comparison reveals that the Terfenol-D rod provides higher blocking forces than its PZT counterpart. It is thus feasible to employ small magnetostrictive drivers in applications involving zero or near-zero displacement, particularly those based on hybrid magnetostrictive/piezoelectric designs in which high efficiencies are achieved by driving the two electrically complementary transducer materials at electrical resonance.

29 CFR 1919.32 - Specially designed blocks and components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Specially designed blocks and components. 1919.32 Section 1919.32 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... Treatment; Competent Persons § 1919.32 Specially designed blocks and components. (a) Blocks and connecting...

Visuospatial, visuoperceptual, and visuoconstructive abilities in congenital hypothyroidism.

PubMed

Simic, Nevena; Khan, Sarah; Rovet, Joanne

2013-11-01

Individuals with congenital hypothyroidism (CH), even those diagnosed and treated early, experience selective cognitive deficits, the most striking of which involves the visuocognitive domain. However, the range and nature of their visuocognitive disturbances is not fully understood. We assessed a range of higher-order visuocognitive abilities in 19 children and adolescents with CH and 19 age- and sex-matched typically developing peers (TD) using a battery of neuropsychological tests and a novel self-report measure of sense of direction. CH scored lower than TD on direct tests of visuocognitive function (judging line orientation, parts-to-whole localization, copying three-dimensional block towers, discriminating designs, and matching unfamiliar faces in ¾ profile-view) as well as on self-reported problems in spatial ability. Visuocognitive problems were not global as CH and TD did not differ at copying two-dimensional block designs, mentally rotating and matching abstract shapes, or at matching unfamiliar front-view faces, design features, or designs that engaged either figure-ground segregation, visual constancy, or closure. Early and concurrent thyroid stimulating hormone (TSH) levels were associated with visuocognitive ability, although attention and working memory were not. Individuals with CH exhibit selective visuocognitive weaknesses, some of which are related to early and concurrent TSH levels.

A tribo-mechanical analysis of PVA-based building-blocks for implementation in a 2-layered skin model.

PubMed

Morales Hurtado, M; de Vries, E G; Zeng, X; van der Heide, E

2016-09-01

Poly(vinyl) alcohol hydrogel (PVA) is a well-known polymer widely used in the medical field due to its biocompatibility properties and easy manufacturing. In this work, the tribo-mechanical properties of PVA-based blocks are studied to evaluate their suitability as a part of a structure simulating the length scale dependence of human skin. Thus, blocks of pure PVA and PVA mixed with Cellulose (PVA-Cel) were synthesised via freezing/thawing cycles and their mechanical properties were determined by Dynamic Mechanical Analysis (DMA) and creep tests. The dynamic tests addressed to elastic moduli between 38 and 50kPa for the PVA and PVA-Cel, respectively. The fitting of the creep compliance tests in the SLS model confirmed the viscoelastic behaviour of the samples with retardation times of 23 and 16 seconds for the PVA and PVA-Cel, respectively. Micro indentation tests were also achieved and the results indicated elastic moduli in the same range of the dynamic tests. Specifically, values between 45-55 and 56-81kPa were obtained for the PVA and PVA-Cel samples, respectively. The tribological results indicated values of 0.55 at low forces for the PVA decreasing to 0.13 at higher forces. The PVA-Cel blocks showed lower friction even at low forces with values between 0.2 and 0.07. The implementation of these building blocks in the design of a 2-layered skin model (2LSM) is also presented in this work. The 2LSM was stamped with four different textures and their surface properties were evaluated. The hydration of the 2LSM was also evaluated with a corneometer and the results indicated a gradient of hydration comparable to the human skin. Copyright © 2016 Elsevier Ltd. All rights reserved.

Investigation on the Core Bypass Flow in a Very High Temperature Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hassan, Yassin

2013-10-22

Uncertainties associated with the core bypass flow are some of the key issues that directly influence the coolant mass flow distribution and magnitude, and thus the operational core temperature profiles, in the very high-temperature reactor (VHTR). Designers will attempt to configure the core geometry so the core cooling flow rate magnitude and distribution conform to the design values. The objective of this project is to study the bypass flow both experimentally and computationally. Researchers will develop experimental data using state-of-the-art particle image velocimetry in a small test facility. The team will attempt to obtain full field temperature distribution using racksmore » of thermocouples. The experimental data are intended to benchmark computational fluid dynamics (CFD) codes by providing detailed information. These experimental data are urgently needed for validation of the CFD codes. The following are the project tasks: • Construct a small-scale bench-top experiment to resemble the bypass flow between the graphite blocks, varying parameters to address their impact on bypass flow. Wall roughness of the graphite block walls, spacing between the blocks, and temperature of the blocks are some of the parameters to be tested. • Perform CFD to evaluate pre- and post-test calculations and turbulence models, including sensitivity studies to achieve high accuracy. • Develop the state-of-the art large eddy simulation (LES) using appropriate subgrid modeling. • Develop models to be used in systems thermal hydraulics codes to account and estimate the bypass flows. These computer programs include, among others, RELAP3D, MELCOR, GAMMA, and GAS-NET. Actual core bypass flow rate may vary considerably from the design value. Although the uncertainty of the bypass flow rate is not known, some sources have stated that the bypass flow rates in the Fort St. Vrain reactor were between 8 and 25 percent of the total reactor mass flow rate. If bypass flow rates are on the high side, the quantity of cooling flow through the core may be considerably less than the nominal design value, causing some regions of the core to operate at temperatures in excess of the design values. These effects are postulated to lead to localized hot regions in the core that must be considered when evaluating the VHTR operational and accident scenarios.« less

In Vitro Comparative Analysis of Fracture Resistance in Inlay Restoration Prepared with CAD-CAM and Different Systems in the Primary Teeth

PubMed Central

Derelioglu, Sera

2016-01-01

Objective. The aim of this study was to compare to fracture resistance test of inlay restorations prepared using direct inlay technique (Gradia® Direct Composite) and Indirect Restoration System® (Gradia Indirect Composite) and CAD/CAD system (Vita Enamic® Block). Study Design. 48 noncarious extracted maxillary second primary molars were randomly divided into 4 groups with 12 in each group. All the teeth were prepared based on inlay class II preparations except for the control group. Other groups were restored with Gradia Direct Composite, Gradia Indirect Composite, and Vita Enamic Block, respectively. All restorations were cemented self-adhesive dual cure resin (3M Espe, RelyX™ Unicem Aplicap). A fracture test was performed using a compressive load. Results were analyzed using one-way analysis of variance and Duncan's post hoc multiple comparison tests (α = 0.05). Results. Vita Enamic Block and Gradia Indirect Composite showed significantly higher fracture resistance than Gradia Direct Composite (p < 0.05). There was no significant difference fracture resistance between Vita Enamic Block and Gradia Indirect Composite (p > 0.05). All restorations tested led to a significant reduction in fracture resistance (p < 0.05). Conclusion. In inlay restorations, Indirect Restoration Systems and CAD/CAM systems were applied successfully together with the self-adhesive dual cure resin cements in primary molars. PMID:27830145

Neural correlates of differential retrieval orientation: Sustained and item-related components.

PubMed

Woodruff, C Chad; Uncapher, Melina R; Rugg, Michael D

2006-01-01

Retrieval orientation refers to a cognitive state that biases processing of retrieval cues in service of a specific goal. The present study used a mixed fMRI design to investigate whether adoption of different retrieval orientations - as indexed by differences in the activity elicited by retrieval cues corresponding to unstudied items - is associated with differences in the state-related activity sustained across a block of test trials sharing a common retrieval goal. Subjects studied mixed lists comprising visually presented words and pictures. They then undertook a series of short test blocks in which all test items were visually presented words. The blocks varied according to whether the test items were used to cue retrieval of studied words or studied pictures. In several regions, neural activity elicited by correctly classified new items differed according to whether words or pictures were the targeted material. The loci of these effects suggest that one factor driving differential cue processing is modulation of the degree of overlap between cue and targeted memory representations. In addition to these item-related effects, neural activity sustained throughout the test blocks also differed according to the nature of the targeted material. These findings indicate that the adoption of different retrieval orientations is associated with distinct neural states. The loci of these sustained effects were distinct from those where new item activity varied, suggesting that the effects may play a role in biasing retrieval cue processing in favor of the current retrieval goal.

Heterophilic interference in specimens yielding false-reactive results on the Abbott 4th generation ARCHITECT HIV Ag/Ab Combo assay.

PubMed

Lavoie, S; Caswell, D; Gill, M J; Kadkhoda, K; Charlton, C L; Levett, P N; Hatchette, T; Garceau, R; Maregmen, J; Mazzulli, T; Needle, R; Kadivar, K; Kim, J

2018-07-01

False-reactivity in HIV-negative specimens has been detected in HIV fourth-generation antigen/antibody or 'combo' assays which are able to detect both anti-HIV-1/HIV-2 antibodies and HIV-1 antigen. We sought to characterize these specimens and determine the effect of heterophilic interference. Specimens previously testing as false-reactive on the Abbott ARCHITECT HIV Ag/Ab combo assay and re-tested on a different (Siemens ADVIA Centaur HIV Ag/Ab) assay. A subset of these specimens were also pre-treated with heterophilic blocking agents and re-tested on the Abbott assay. Here we report that 95% (252/264) of clinical specimens that were repeatedly reactive on the Abbott ARCHITECT HIV Ag/Ab combo assay (S/Co range, 0.94-678) were negative when re-tested on a different fourth generation HIV combo assay (Siemens ADVIA Centaur HIV Ag/Ab). All 264 samples were subsequently confirmed to be HIV negative. On a small subset (57) of specimens with available volume, pre-treatment with two different reagents (HBT; Heterophilic Blocking Tube, NABT; Non-Specific Blocking Tube) designed to block heterophilic antibody interference either eliminated (HBT) or reduced (NABT) the false reactivity when re-tested on the ARCHITECT HIV Ag/Ab combo assay. Our results suggest that the Abbott ARCHITECT HIV Ag/Ab combo assay can be prone to heterophilic antibody interference. Crown Copyright © 2018. Published by Elsevier B.V. All rights reserved.

Comparison of Periodontal Ligament Injection and Inferior Alveolar Nerve Block in Mandibular Primary Molars Pulpotomy: A Randomized Control Trial

PubMed Central

Haghgoo, Roza; Taleghani, Ferial

2015-01-01

Background: Inferior alveolar nerve block is a common technique for anesthesia of the primary mandibular molars. A number of disadvantages have been shown to be associated with this technique. Periodontal ligament (PDL) injection could be considered as an alternative to inferior alveolar nerve block. The aim of this study was to evaluate the effectiveness of PDL injection in the anesthesia of primary molar pulpotomy with mandibular block. Methods: This study was performed using a sequential double-blind randomized trial design. 80 children aged 3-7 years old who required pulpotomy in symmetrical mandibular primary molars were selected. The teeth of these children were anesthetized with periodontal injection on one side of the mandible and block on the other. Pulpotomy was performed on each patient during the same appointment. Signs of discomfort, including hand and body tension and eye movement, the verbal complaint and crying (SEM scale), were evaluated by a dental assistant who was blinded to the treatment allocation of the patients. Finally, the data were analyzed using the exact Fisher test and Pearson Chi-squared exact test. Results: Success rate was 88/75 and 91/25 in the PDL injection and nerve block groups, respectively. There was no statistically significant difference between the two techniques (P = 0.250). Conclusion: Results showed that PDL injection can be used as an alternative to nerve block in pulpotomy of the mandibular primary molars. PMID:26028895

Spacecraft Data Simulator for the test of level zero processing systems

NASA Technical Reports Server (NTRS)

Shi, Jeff; Gordon, Julie; Mirchandani, Chandru; Nguyen, Diem

1994-01-01

The Microelectronic Systems Branch (MSB) at Goddard Space Flight Center (GSFC) has developed a Spacecraft Data Simulator (SDS) to support the development, test, and verification of prototype and production Level Zero Processing (LZP) systems. Based on a disk array system, the SDS is capable of generating large test data sets up to 5 Gigabytes and outputting serial test data at rates up to 80 Mbps. The SDS supports data formats including NASA Communication (Nascom) blocks, Consultative Committee for Space Data System (CCSDS) Version 1 & 2 frames and packets, and all the Advanced Orbiting Systems (AOS) services. The capability to simulate both sequential and non-sequential time-ordered downlink data streams with errors and gaps is crucial to test LZP systems. This paper describes the system architecture, hardware and software designs, and test data designs. Examples of test data designs are included to illustrate the application of the SDS.

A Characterization of BIB Designs Based on v Treatments in Blocks of Size k Whose Number of Blocks is at Least vCk.

DTIC Science & Technology

1981-01-01

Discrete Math . 6, 189-200. Foody, W. and A. Hedayat, (1977). On theory and applications of BIB designs with repeated blocks. Ann. Statist. 5, i •, 932...945. Corrections: Ann. Statist. 7 (1979). 925. van Lint, J.I1. and H.J. Ryser (1972). Block designs with repeated blocks. Discrete Math ., 3, 381-396

21 CFR 882.1925 - Ultrasonic scanner calibration test block.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultrasonic scanner calibration test block. 882... Ultrasonic scanner calibration test block. (a) Identification. An ultrasonic scanner calibration test block is a block of material with known properties used to calibrate ultrasonic scanning devices (e.g., the...

Prototyping high-gradient mm-wave accelerating structures

DOE PAGES

Nanni, Emilio A.; Dolgashev, Valery A.; Haase, Andrew; ...

2017-01-01

We present single-cell accelerating structures designed for high-gradient testing at 110 GHz. The purpose of this work is to study the basic physics of ultrahigh vacuum RF breakdown in high-gradient RF accelerators. The accelerating structures are π-mode standing-wave cavities fed with a TM 01 circular waveguide. The structures are fabricated using precision milling out of two metal blocks, and the blocks are joined with diffusion bonding and brazing. The impact of fabrication and joining techniques on the cell geometry and RF performance will be discussed. First prototypes had a measured Q 0 of 2800, approaching the theoretical design value ofmore » 3300. The geometry of these accelerating structures are as close as practical to singlecell standing-wave X-band accelerating structures more than 40 of which were tested at SLAC. This wealth of X-band data will serve as a baseline for these 110 GHz tests. Furthermore, the structures will be powered with short pulses from a MW gyrotron oscillator. RF power of 1 MW may allow an accelerating gradient of 400 MeV/m to be reached.« less

Development of an In-Situ Decommissioning Sensor Network Test Bed for Structural Condition Monitoring - 12156

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeigler, Kristine E.; Ferguson, Blythe A.

2012-07-01

The Savannah River National Laboratory (SRNL) has established an In Situ Decommissioning (ISD) Sensor Network Test Bed, a unique, small scale, configurable environment, for the assessment of prospective sensors on actual ISD system material, at minimal cost. The Department of Energy (DOE) is presently implementing permanent entombment of contaminated, large nuclear structures via ISD. The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. Validation of ISD system performance models and verification of actual system conditions can be achieved through the development a system of sensors to monitor the materials andmore » condition of the structure. The ISD Sensor Network Test Bed has been designed and deployed to addresses the DOE-Environmental Management Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building at the Savannah River Site. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of groutable thermistors for temperature and moisture monitoring, strain gauges for crack growth monitoring, tilt-meters for settlement monitoring, and a communication system for data collection. Baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment. The Sensor Network Test Bed at SRNL uses COTS sensors on concrete blocks from the outer wall of the P Reactor Building to measure conditions expected to occur in ISD structures. Knowledge and lessons learned gained from installation, testing, and monitoring of the equipment will be applied to sensor installation in a meso-scale test bed at FIU and in future ISD structures. The initial data collected from the sensors installed on the P Reactor Building blocks define the baseline materials condition of the P Reactor ISD external concrete structure. Continued monitoring of the blocks will enable evaluation of the effects of aging on the P Reactor ISD structure. The collected data will support validation of the material degradation model and assessment of the condition of the ISD structure over time. The following are recommendations for continued development of the ISD Sensor Network Test Bed: - Establish a long-term monitoring program using the concrete blocks with existing sensor and/or additional sensors for trending the concrete materials and structural condition; - Continue development of a stand-alone test bed sensor system that is self-powered and provides wireless transmission of data to a user-accessible dashboard; - Develop and implement periodic NDE/DE characterization of the concrete blocks to provide verification and validation for the measurements obtained through the sensor system and concrete degradation model(s). (authors)« less

Designing Technology for Children: Moving from the Computer into the Physical World with Electronic Blocks

ERIC Educational Resources Information Center

Wyeth, Peta; Purchase, Helen

2002-01-01

Electronic Blocks are a new programming environment designed specifically for children between three and eight years of age. As such, the design of the Electronic Block environment is firmly based on principles of developmentally appropriate practices in early childhood education. Electronic Blocks are the physical embodiment of computer…

Testing the Impact of a Pre-Instructional Digital Game on Middle-Grade Students' Understanding of Photosynthesis

ERIC Educational Resources Information Center

Culp, Katherine McMillan; Martin, Wendy; Clements, Margaret; Lewis Presser, Ashley

2015-01-01

Rigorous studies of the impact of digital games on student learning remain relatively rare, as do studies of games as supports for learning difficult, core curricular concepts in the context of normal classroom practices. This study uses a blocked, cluster randomized controlled trial design to test the impact of a digital game, played as homework…

29 CFR Appendix E to Subpart L of... - Test Methods for Protective Clothing

Code of Federal Regulations, 2010 CFR

2010-07-01

... test ensemble consisting of the sample unit, the two prepared blocks, a piece of leather outsole 10 to... perpendicular to the 1-inch (2.5 cm) edge. B. Apparatus. (i) Six-ounce (.17 kg) weight tension clamps shall be used so designed that the six ounces (.17 kg) of weight are distributed evenly across the complete...

NASA's Space Launch System: Systems Engineering Approach for Affordability and Mission Success

NASA Technical Reports Server (NTRS)

Hutt, John J.; Whitehead, Josh; Hanson, John

2017-01-01

NASA is working toward the first launch of a new, unmatched capability for deep space exploration, with launch readiness planned for 2018. The initial Block 1 configuration of the Space Launch System will more than double the mass and volume to Low Earth Orbit (LEO) of any launch vehicle currently in operation - with a path to evolve to the greatest capability ever developed. The program formally began in 2011. The vehicle successfully passed Preliminary Design Review (PDR) in 2013, Key Decision Point C (KDPC) in 2014 and Critical Design Review (CDR) in October 2015 - nearly 40 years since the last CDR of a NASA human-rated rocket. Every major SLS element has completed components of test and flight hardware. Flight software has completed several development cycles. RS-25 hotfire testing at NASA Stennis Space Center (SSC) has successfully demonstrated the space shuttle-heritage engine can perform to SLS requirements and environments. The five-segment solid rocket booster design has successfully completed two full-size motor firing tests in Utah. Stage and component test facilities at Stennis and NASA Marshall Space Flight Center are nearing completion. Launch and test facilities, as well as transportation and other ground support equipment are largely complete at NASA's Kennedy, Stennis and Marshall field centers. Work is also underway on the more powerful Block 1 B variant with successful completion of the Exploration Upper Stage (EUS) PDR in January 2017. NASA's approach is to develop this heavy lift launch vehicle with limited resources by building on existing subsystem designs and existing hardware where available. The systems engineering and integration (SE&I) of existing and new designs introduces unique challenges and opportunities. The SLS approach was designed with three objectives in mind: 1) Design the vehicle around the capability of existing systems; 2) Reduce work hours for nonhardware/ software activities; 3) Increase the probability of mission success by focusing effort on more critical activities.

A new device to test cutting efficiency of mechanical endodontic instruments

PubMed Central

Rubini, Alessio Giansiracusa; Plotino, Gianluca; Al-Sudani, Dina; Grande, Nicola M.; Putorti, Ermanno; Sonnino, GianPaolo; Cotti, Elisabetta; Testarelli, Luca; Gambarini, Gianluca

2014-01-01

Background The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments. Material/Methods Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the “Reciproc ALL” program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P<0.05). Results Reciproc in reciprocation (Group 1) mean cut in the Plexiglas block was 8.6 mm (SD=0.6 mm), while Reciproc in rotation mean cut was 8.9 mm (SD=0.7 mm). There was no statistically significant difference between the 2 groups investigated (P>0.05). Conclusions The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments. PMID:24603777

PEG Enhancement for EM1 and EM2+ Missions

NASA Technical Reports Server (NTRS)

Von der Porten, Paul; Ahmad, Naeem; Hawkins, Matt

2018-01-01

NASA is currently building the Space Launch System (SLS) Block-1 launch vehicle for the Exploration Mission 1 (EM-1) test flight. The next evolution of SLS, the Block-1B Exploration Mission 2 (EM-2), is currently being designed. The Block-1 and Block-1B vehicles will use the Powered Explicit Guidance (PEG) algorithm. Due to the relatively low thrust-to-weight ratio of the Exploration Upper Stage (EUS), certain enhancements to the Block-1 PEG algorithm are needed to perform Block-1B missions. In order to accommodate mission design for EM-2 and beyond, PEG has been significantly improved since its use on the Space Shuttle program. The current version of PEG has the ability to switch to different targets during Core Stage (CS) or EUS flight, and can automatically reconfigure for a single Engine Out (EO) scenario, loss of communication with the Launch Abort System (LAS), and Inertial Navigation System (INS) failure. The Thrust Factor (TF) algorithm uses measured state information in addition to a priori parameters, providing PEG with an improved estimate of propulsion information. This provides robustness against unknown or undetected engine failures. A loft parameter input allows LAS jettison while maximizing payload mass. The current PEG algorithm is now able to handle various classes of missions with burn arcs much longer than were seen in the shuttle program. These missions include targeting a circular LEO orbit with a low-thrust, long-burn-duration upper stage, targeting a highly eccentric Trans-Lunar Injection (TLI) orbit, targeting a disposal orbit using the low-thrust Reaction Control System (RCS), and targeting a hyperbolic orbit. This paper will describe the design and implementation of the TF algorithm, the strategy to handle EO in various flight regimes, algorithms to cover off-nominal conditions, and other enhancements to the Block-1 PEG algorithm. This paper illustrates challenges posed by the Block-1B vehicle, and results show that the improved PEG algorithm is capable for use on the SLS Block 1-B vehicle as part of the Guidance, Navigation, and Control System.

Elevated airborne manganese and low executive function in school-aged children in Brazil.

PubMed

Carvalho, Chrissie F; Menezes-Filho, José A; de Matos, Vitor P; Bessa, Jonatas Reis; Coelho-Santos, Juliana; Viana, Gustavo F S; Argollo, Nayara; Abreu, Neander

2014-12-01

Exposure to airborne manganese (Mn) has been associated with neurotoxic effects, including motor and cognitive deficits. The main deficits related to excessive exposure to Mn are predominantly the dysfunction of fronto-striatal and dopaminergic circuits observed in animal experimental studies, which are involved in attention, working memory and motor function. The present study aims to assess the association between elevated Mn exposure and performance on executive function and attention neuropsychological tests in children living in two communities near a ferro-manganese alloy plant. Seventy children aged between 7 and 12 years with no history of neurologic disease and an estimated IQ >68 (Vocabulary and Block Design subtests) that had lived near the iron-Mn production alloy plant for at least 1.5 years were included. Participants were assessed for cognitive functioning with neuropsychological measures for sustained attention (Test of Visual Attention - TAVIS-3R), cognitive flexibility (WCST), and verbal and visual working memory (WISC-III Digit Span subtest and Corsi Block). Manganese hair (MnH) levels were used as a biomarker of exposure. Mean scores among study participants were lower than general population norms/averages for block design, digit span, reaction time and commission errors. The median MnH level was 11.48 (range 0.52-55.74) μg/g, and no difference between sexes was observed. Spearman's correlation analysis showed a significant inverse correlation between MnH levels and estimated IQ (rho=-0.448, p=0.0001), Vocabulary (rho=-0.272, p=0.02), Block Design (rho=-0.485, p=0.00002) and Digit Span (rho=-0.410, p=0.0004). Multiple regression analyses detected inverse associations between log MnH and scores on estimated IQ (β=-9.67; 95%CI=-16.97 to -2.37), Block Design (β=-2.50; 95%CI=-3.91 to -1.10) and Digit Span Total (β=-2.59; 95%CI=-4.13 to -1.05) standardized scores and the number of correct answers in forward and backward Digit Span methods, after adjusting for covariates (β=-1.32=95%CI=-2.23 to -0.40; β=-1.09 95%CI=-2.02 to -0.16, respectively). The results suggest that airborne Mn exposure may be associated with lower IQ and neuropsychological performance in tests of executive function of inhibition responses, strategic visual formation and verbal working memory. Executive function is dependent on the fronto-striatal circuit, which may be disrupted by Mn accumulation in the brain. Copyright © 2013 Elsevier Inc. All rights reserved.

SKIRT: The design of a suite of input models for Monte Carlo radiative transfer simulations

NASA Astrophysics Data System (ADS)

Baes, M.; Camps, P.

2015-09-01

The Monte Carlo method is the most popular technique to perform radiative transfer simulations in a general 3D geometry. The algorithms behind and acceleration techniques for Monte Carlo radiative transfer are discussed extensively in the literature, and many different Monte Carlo codes are publicly available. On the contrary, the design of a suite of components that can be used for the distribution of sources and sinks in radiative transfer codes has received very little attention. The availability of such models, with different degrees of complexity, has many benefits. For example, they can serve as toy models to test new physical ingredients, or as parameterised models for inverse radiative transfer fitting. For 3D Monte Carlo codes, this requires algorithms to efficiently generate random positions from 3D density distributions. We describe the design of a flexible suite of components for the Monte Carlo radiative transfer code SKIRT. The design is based on a combination of basic building blocks (which can be either analytical toy models or numerical models defined on grids or a set of particles) and the extensive use of decorators that combine and alter these building blocks to more complex structures. For a number of decorators, e.g. those that add spiral structure or clumpiness, we provide a detailed description of the algorithms that can be used to generate random positions. Advantages of this decorator-based design include code transparency, the avoidance of code duplication, and an increase in code maintainability. Moreover, since decorators can be chained without problems, very complex models can easily be constructed out of simple building blocks. Finally, based on a number of test simulations, we demonstrate that our design using customised random position generators is superior to a simpler design based on a generic black-box random position generator.

Proceedings of the Conference on the Design of Experiments in Army Research Development and Testing (28th) Held at Monterey, California on 20-22 October 1982

DTIC Science & Technology

1983-06-01

program specifically designed to solve IME equations. The IME measure is a useful index because it translates system performance characteristics of...8.0 SUMMARY The purpose of this study was to design the field evaluation of a camou- flage system in such a manner that the camoufleur could...analysis of complex factorial designs and their associated systems of confounding ((44), [46)) and to the introduction of incomplete block designs . My

Fuel Regression Characteristics of Cascaded Multistage Impinging-Jet (CAMUI) Type Hybrid Rocket

NASA Astrophysics Data System (ADS)

Itoh, Mitsunori; Maeda, Takenori; Kakikura, Akihito; Kaneko, Yudai; Mori, Kazuhiro; Nakashima, Takuji; Wakita, Masashi; Uematsu, Tsutomu; Totani, Tsuyoshi; Oshima, Nobuyuki; Nagata, Harunori

A series of lab-scale firing tests was conducted to investigate the fuel regression characteristics of Cascaded Multistage Impinging-jet (CAMUI) type hybrid rocket. The alternative fuel grain used in this rocket consists of a number of cylindrical fuel blocks with two ports, which were aligned along the axis of the combustion chamber with a small gap. The ports are aligned staggered with respect to ones of neighboring blocks so that the combustion gas flow impinges on the forward-end surface of each block. In this fuel grain, forward-end surfaces, back-end surfaces and ports of fuel blocks contribute as burning surfaces. Polyethylene and LOX were used as a propellant, and the tests were conducted at the chamber pressure of 0.5 2MPa and the mass flux of 50 200kg/m2s. Main results obtained in this study are in the followings: The regression rate of each surface was obtained as a function of the propellant mass flux and local equivalent ratio of the combustion gas. At back-end surfaces the regression rate has a high sensitivity on the gap height of neighboring fuel blocks. These fuel regression characteristics will contribute as fundamental data to improve the optimum design of the fuel grain.

Reflective Occultation Mask for Evaluation of Occulter Designs for Planet Finding

NASA Technical Reports Server (NTRS)

Hagopian, John; Lyon, Richard; Shiri, Shahram; Roman, Patrick

2011-01-01

Advanced formation flying occulter designs utilize a large occulter mask flying in formation with an imaging telescope to block and null starlight to allow imaging of faint planets in exosolar systems. A paper describes the utilization of subscale reflective occultation masks to evaluate formation flying occulter designs. The use of a reflective mask allows mounting of the occulter by conventional means and simplifies the test configuration. The innovation alters the test set-up to allow mounting of the mask using standard techniques to eliminate the problems associated with a standard configuration. The modified configuration uses a reflective set-up whereby the star simulator reflects off of a reflective occulting mask and into an evaluation telescope. Since the mask is sized to capture all rays required for the imaging test, it can be mounted directly to a supporting fixture without interfering with the beam. Functionally, the reflective occultation mask reflects light from the star simulator instead of transmitting it, with a highly absorptive carbon nanotube layer simulating the occulter blocking mask. A subscale telescope images the star source and companion dim source that represents a planet. The primary advantage of this is that the occulter can be mounted conventionally instead of using diffractive wires or magnetic levitation.

Differences between Art and Design Education--or Differences in Conceptions of Creativity?

ERIC Educational Resources Information Center

Zwirn, Susan Goetz; Vande Zande, Robin

2017-01-01

The principles and techniques of design education have begun to influence art education in the United States, but their effect so far has been modest, primarily because of a gaping divide in beliefs about creativity and how to stimulate it. With K-12 art education on the chopping block of a culture awash with budget cuts and testing fever, this is…

DESIGN CHARACTERISTICS OF THE IDAHO NATIONAL LABORATORY HIGH-[TEMPERATURE GAS-COOLED TEST REACTOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterbentz, James; Bayless, Paul; Strydom, Gerhard

A point design for a graphite-moderated, high-temperature, gas-cooled test reactor (HTG TR) has been developed by Idaho National Laboratory (INL) as part of a United States (U.S.) Department of Energy (DOE) initiative to explore and potentially expand the existing U.S. test reactor capabilities. This paper provides a summary of the design and its main attributes. The 200 MW HTG TR is a thermal-neutron spectrum reactor composed of hexagonal prismatic fuel and graphite reflector blocks. Twelve fuel columns (96 fuel blocks total and 6.34 m active core height) are arranged in two hexagonal rings to form a relatively compact, high-power density,more » annular core sandwiched between inner, outer, top, and bottom graphite reflectors. The HTG-TR is designed to operate at 7 MPa with a coolant inlet/outlet temperature of 325°C/650°C, and utilizes TRISO particle fuel from the DOE AGR Program with 425 ?m uranium oxycarbide (UCO) kernels and an enrichment of 15.5 wt% 235U. The primary mission of the HTG TR is material irradiation and therefore the core has been specifically designed and optimized to provide the highest possible thermal and fast neutron fluxes. The highest thermal neutron flux (3.90E+14 n/cm2s) occurs in the outer reflector, and the maximum fast flux levels (1.17E+14 n/cm2s) are produced in the central reflector column where most of the graphite has been removed. Due to high core temperatures under accident conditions, all the irradiation test facilities have been located in the inner and outer reflectors where fast flux levels decline. The core features a large number of irradiation positions with large test volumes and long test lengths, ideal for thermal neutron irradiation of large test articles. The total available test volume is more than 1100 liters. Up to four test loop facilities can be accommodated with pressure tube boundaries to isolate test articles and test fluids (e.g., liquid metal, liquid salt, light water) from the helium primary coolant system.« less

Color Image Classification Using Block Matching and Learning

NASA Astrophysics Data System (ADS)

Kondo, Kazuki; Hotta, Seiji

In this paper, we propose block matching and learning for color image classification. In our method, training images are partitioned into small blocks. Given a test image, it is also partitioned into small blocks, and mean-blocks corresponding to each test block are calculated with neighbor training blocks. Our method classifies a test image into the class that has the shortest total sum of distances between mean blocks and test ones. We also propose a learning method for reducing memory requirement. Experimental results show that our classification outperforms other classifiers such as support vector machine with bag of keypoints.

Electronically Tunable Differential Integrator: Linear Voltage Controlled Quadrature Oscillator.

PubMed

Nandi, Rabindranath; Pattanayak, Sandhya; Venkateswaran, Palaniandavar; Das, Sagarika

2015-01-01

A new electronically tunable differential integrator (ETDI) and its extension to voltage controlled quadrature oscillator (VCQO) design with linear tuning law are proposed; the active building block is a composite current feedback amplifier with recent multiplication mode current conveyor (MMCC) element. Recently utilization of two different kinds of active devices to form a composite building block is being considered since it yields a superior functional element suitable for improved quality circuit design. The integrator time constant (τ) and the oscillation frequency (ω o ) are tunable by the control voltage (V) of the MMCC block. Analysis indicates negligible phase error (θ e ) for the integrator and low active ω o -sensitivity relative to the device parasitic capacitances. Satisfactory experimental verifications on electronic tunability of some wave shaping applications by the integrator and a double-integrator feedback loop (DIFL) based sinusoid oscillator with linear f o variation range of 60 KHz~1.8 MHz at low THD of 2.1% are verified by both simulation and hardware tests.

Prospective power calculations for the Four Lab study of a multigenerational reproductive/developmental toxicity rodent bioassay using a complex mixture of disinfection by-products in the low-response region.

PubMed

Dingus, Cheryl A; Teuschler, Linda K; Rice, Glenn E; Simmons, Jane Ellen; Narotsky, Michael G

2011-10-01

In complex mixture toxicology, there is growing emphasis on testing environmentally representative doses that improve the relevance of results for health risk assessment, but are typically much lower than those used in traditional toxicology studies. Traditional experimental designs with typical sample sizes may have insufficient statistical power to detect effects caused by environmentally relevant doses. Proper study design, with adequate statistical power, is critical to ensuring that experimental results are useful for environmental health risk assessment. Studies with environmentally realistic complex mixtures have practical constraints on sample concentration factor and sample volume as well as the number of animals that can be accommodated. This article describes methodology for calculation of statistical power for non-independent observations for a multigenerational rodent reproductive/developmental bioassay. The use of the methodology is illustrated using the U.S. EPA's Four Lab study in which rodents were exposed to chlorinated water concentrates containing complex mixtures of drinking water disinfection by-products. Possible experimental designs included two single-block designs and a two-block design. Considering the possible study designs and constraints, a design of two blocks of 100 females with a 40:60 ratio of control:treated animals and a significance level of 0.05 yielded maximum prospective power (~90%) to detect pup weight decreases, while providing the most power to detect increased prenatal loss.

Prospective Power Calculations for the Four Lab Study of A Multigenerational Reproductive/Developmental Toxicity Rodent Bioassay Using A Complex Mixture of Disinfection By-Products in the Low-Response Region

PubMed Central

Dingus, Cheryl A.; Teuschler, Linda K.; Rice, Glenn E.; Simmons, Jane Ellen; Narotsky, Michael G.

2011-01-01

In complex mixture toxicology, there is growing emphasis on testing environmentally representative doses that improve the relevance of results for health risk assessment, but are typically much lower than those used in traditional toxicology studies. Traditional experimental designs with typical sample sizes may have insufficient statistical power to detect effects caused by environmentally relevant doses. Proper study design, with adequate statistical power, is critical to ensuring that experimental results are useful for environmental health risk assessment. Studies with environmentally realistic complex mixtures have practical constraints on sample concentration factor and sample volume as well as the number of animals that can be accommodated. This article describes methodology for calculation of statistical power for non-independent observations for a multigenerational rodent reproductive/developmental bioassay. The use of the methodology is illustrated using the U.S. EPA’s Four Lab study in which rodents were exposed to chlorinated water concentrates containing complex mixtures of drinking water disinfection by-products. Possible experimental designs included two single-block designs and a two-block design. Considering the possible study designs and constraints, a design of two blocks of 100 females with a 40:60 ratio of control:treated animals and a significance level of 0.05 yielded maximum prospective power (~90%) to detect pup weight decreases, while providing the most power to detect increased prenatal loss. PMID:22073030

SLS Block 1-B and Exploration Upper Stage Navigation System Design

NASA Technical Reports Server (NTRS)

Oliver, T. Emerson; Park, Thomas B.; Smith, Austin; Anzalone, Evan; Bernard, Bill; Strickland, Dennis; Geohagan, Kevin; Green, Melissa; Leggett, Jarred

2018-01-01

The SLS Block 1B vehicle is planned to extend NASA's heavy lift capability beyond the initial SLS Block 1 vehicle. The most noticeable change for this vehicle from SLS Block 1 is the swapping of the upper stage from the Interim Cryogenic Propulsion stage (ICPS), a modified Delta IV upper stage, to the more capable Exploration Upper Stage (EUS). As the vehicle evolves to provide greater lift capability and execute more demanding missions so must the SLS Integrated Navigation System to support those missions. The SLS Block 1 vehicle carries two independent navigation systems. The responsibility of the two systems is delineated between ascent and upper stage flight. The Block 1 navigation system is responsible for the phase of flight between the launch pad and insertion into Low-Earth Orbit (LEO). The upper stage system assumes the mission from LEO to payload separation. For the Block 1B vehicle, the two functions are combined into a single system intended to navigate from ground to payload insertion. Both are responsible for self-disposal once payload delivery is achieved. The evolution of the navigation hardware and algorithms from an inertial-only navigation system for Block 1 ascent flight to a tightly coupled GPS-aided inertial navigation system for Block 1-B is described. The Block 1 GN&C system has been designed to meet a LEO insertion target with a specified accuracy. The Block 1-B vehicle navigation system is designed to support the Block 1 LEO target accuracy as well as trans-lunar or trans-planetary injection accuracy. This is measured in terms of payload impact and stage disposal requirements. Additionally, the Block 1-B vehicle is designed to support human exploration and thus is designed to minimize the probability of Loss of Crew (LOC) through high-quality inertial instruments and Fault Detection, Isolation, and Recovery (FDIR) logic. The preliminary Block 1B integrated navigation system design is presented along with the challenges associated with meeting the design objectives. This paper also addresses the design considerations associated with the use of Block 1 and Commercial Off-the-Shelf (COTS) avionics for Block 1-B/EUS as part of an integrated vehicle suite for orbital operations.

A novel directional asymmetric sampling search algorithm for fast block-matching motion estimation

NASA Astrophysics Data System (ADS)

Li, Yue-e.; Wang, Qiang

2011-11-01

This paper proposes a novel directional asymmetric sampling search (DASS) algorithm for video compression. Making full use of the error information (block distortions) of the search patterns, eight different direction search patterns are designed for various situations. The strategy of local sampling search is employed for the search of big-motion vector. In order to further speed up the search, early termination strategy is adopted in procedure of DASS. Compared to conventional fast algorithms, the proposed method has the most satisfactory PSNR values for all test sequences.

Implementation of a Readout Circuit on SOI Technology for the Signal Conditioning of a Neutron Detector in Harsh Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben Krit, S.; Coulie-Castellani, K.; Rahajandraibe, W.

2015-07-01

A transistor level implementation of the analog block of a readout system on SOI process is presented here. This system is dedicated to the signal conditioning of a neutron detector in harsh environment. The different parts of the readout circuits are defined. The harsh environment constraints (crossing particle effect, high temperatures) are also detailed and modeled in the circuit in order to test and evaluate the characteristics of the designed block when working under these conditions. (authors)

Visuospatial characteristics of an elderly Chinese population: results from the WAIS-R block design test.

PubMed

Yin, Shufei; Zhu, Xinyi; Huang, Xin; Li, Juan

2015-01-01

Visuospatial deficits have long been recognized as a potential predictor of dementia, with visuospatial ability decline having been found to accelerate in later stages of dementia. We, therefore, believe that the visuospatial performance of patients with mild cognitive impairment (MCI) and dementia (Dem) might change with varying visuospatial task difficulties. This study administered the Wechsler Adult Intelligence Scale-Revised (WAIS-R) Block Design Test (BDT) to determine whether visuospatial ability can help discriminate between MCI patients from Dem patients and normal controls (NC). Results showed that the BDT could contribute to the discrimination between MCI and Dem. Specifically, simple BDT task scores could best distinguish MCI from Dem patients, while difficult BDT task scores could contribute to discriminating between MCI and NC. Given the potential clinical value of the BDT in the diagnosis of Dem and MCI, normative data stratified by age and education for the Chinese elderly population are presented for use in research and clinical settings.

Closed Loop Guidance Trade Study for Space Launch System Block-1B Vehicle

NASA Technical Reports Server (NTRS)

Von der Porten, Paul; Ahmad, Naeem; Hawkins, Matt

2018-01-01

NASA is currently building the Space Launch System (SLS) Block-1 launch vehicle for the Exploration Mission 1 (EM-1) test flight. The design of the next evolution of SLS, Block-1B, is well underway. The Block-1B vehicle is more capable overall than Block-1; however, the relatively low thrust-to-weight ratio of the Exploration Upper Stage (EUS) presents a challenge to the Powered Explicit Guidance (PEG) algorithm used by Block-1. To handle the long burn durations (on the order of 1000 seconds) of EUS missions, two algorithms were examined. An alternative algorithm, OPGUID, was introduced, while modifications were made to PEG. A trade study was conducted to select the guidance algorithm for future SLS vehicles. The chosen algorithm needs to support a wide variety of mission operations: ascent burns to LEO, apogee raise burns, trans-lunar injection burns, hyperbolic Earth departure burns, and contingency disposal burns using the Reaction Control System (RCS). Additionally, the algorithm must be able to respond to a single engine failure scenario. Each algorithm was scored based on pre-selected criteria, including insertion accuracy, algorithmic complexity and robustness, extensibility for potential future missions, and flight heritage. Monte Carlo analysis was used to select the final algorithm. This paper covers the design criteria, approach, and results of this trade study, showing impacts and considerations when adapting launch vehicle guidance algorithms to a broader breadth of in-space operations.

Rubidium atomic frequency standards for GPS Block IIR

NASA Technical Reports Server (NTRS)

Riley, William J.

1990-01-01

The Rubidium Atomic Frequency Standards (RAFS) were provided for the GPS Block IIR NAVSTAR satellites. These satellites will replenish and upgrade the space segment of the Global Positioning System in the mid 1990s. The GPS RAFS Rb clocks are the latest generation of the high-performance rubidium frequency standards. They offer an aging rate in the low pp 10(exp 14)/day range and a drift-corrected 1-day stability in the low pp 10(exp 14) range. The Block IIR version of these devices will have improved performance, higher reliability, smaller size, and greater radiation hardness. The GPS Block IIR atomic clocks have a natural frequency configuration whereby they output a frequency of about 13.4 MHz that is a submultiple of the atomic resonance of Rb (or Cs). The RAFS operates at a low, fixed C-field for increased stability. The GPS Block IIR RAFS design, including the changes and improvements made, and the test results obtained are described.

Learning Potential Among the Moderately and Severely Retarded. Studies in Learning Potential, Volume 3, Number 52.

ERIC Educational Resources Information Center

Hamilton, James L.; Budoff, Milton

The study investigated the feasibility of M. Budoff and M. Friedman's (1964) learning potential paradigm as an assessment approach with 40 moderately and severely mentally retarded persons (aged 12 to 22 years). Ss were tested three times: initially, after one week, and after one month with a match-to-sample block design test. Twenty of the Ss…

Single event upset susceptibility testing of the Xilinx Virtex II FPGA

NASA Technical Reports Server (NTRS)

Yui, C.; Swift, G.; Carmichael, C.

2002-01-01

Heavy ion testing of the Xilinx Virtex IZ was conducted on the configuration, block RAM and user flip flop cells to determine their single event upset susceptibility using LETs of 1.2 to 60 MeVcm^2/mg. A software program specifically designed to count errors in the FPGA is used to reveal L1/e values and single-event-functional interrupt failures.

The Boundaries of the Cognitive Phenotype of Autism: Theory of Mind, Central Coherence and Ambiguous Figure Perception in Young People with Autistic Traits

ERIC Educational Resources Information Center

Best, Catherine S.; Moffat, Vivien J.; Power, Michael J.; Owens, David G. C.; Johnstone, Eve C.

2008-01-01

Theory of Mind, Weak Central Coherence and executive dysfunction, were investigated as a function of behavioural markers of autism. This was irrespective of the presence or absence of a diagnosis of an autistic spectrum disorder. Sixty young people completed the Social Communication Questionnaire (SCQ), false belief tests, the block design test,…

NASA's Space Launch System Program Update

NASA Technical Reports Server (NTRS)

May, Todd; Lyles, Garry

2015-01-01

Hardware and software for the world's most powerful launch vehicle for exploration is being welded, assembled, and tested today in high bays, clean rooms and test stands across the United States. NASA's Space Launch System (SLS) continued to make significant progress in 2014 with more planned for 2015, including firing tests of both main propulsion elements and the program Critical Design Review (CDR). Developed with the goals of safety, affordability, and sustainability, SLS will still deliver unmatched capability for human and robotic exploration. The initial Block 1 configuration will deliver more than 70 metric tons of payload to low Earth orbit (LEO). The evolved Block 2 design will deliver some 130 metric tons to LEO. Both designs offer enormous opportunity and flexibility for larger payloads, simplifying payload design as well as ground and on-orbit operations, shortening interplanetary transit times, and decreasing overall mission risk. Over the past year, every vehicle element has manufactured or tested hardware. An RS-25 liquid propellant engine was hotfire-tested at NASA's Stennis Space Center, Miss. for the first time since 2009 exercising and validating the new engine controller, the renovated A-1 test stand, and the test teams. Four RS-25s will power the SLS core stage. A qualification five-segment solid rocket motor incorporating several design, material, and process changes was scheduled to be test-fired in March at the prime contractor's facility in Utah. The booster also successfully completed its Critical Design Review (CDR) validating the planned design. All six major manufacturing tools for the core stage are in place at the Michoud Assembly Facility in Louisiana, and have been used to build numerous pieces of confidence, qualification, and even flight hardware, including barrel sections, domes and rings used to assemble the world's largest rocket stage. SLS Systems Engineering accomplished several key tasks including vehicle avionics software and hardware build and testing, scale model acoustic and base heating tests. Construction of the Interim Cryogenic Propulsion Stage (ICPS) began. Advanced development provided a look into the future of SLS. Shell buckling knockdown factor testing refined decades-old design margins that added thousands of pounds to rocket payloads. Adaptive manufacturing and structured light scanning development promised to cut the cost and time associated with manufacturing and testing. This paper will provide an overview of the progress made over the past year and provide a glimpse of 2015 milestones and beyond on the way to the first launch in 2018.

The categorisation of swimming start performance with reference to force generation on the main block and footrest components of the Omega OSB11 start blocks.

PubMed

Slawson, Sian E; Conway, Paul P; Cossor, Jodi; Chakravorti, Nandini; West, Andrew A

2013-01-01

Work presented in this paper provides a methodology for categorising swimming start performance based on peak force production on the main block and footrest components of the Omega OSB11 starting block. A total of 46 elite British swimmers were tested, producing over 1000 start trials. Overwater cameras were synchronised to a specifically designed start block that allowed the measurement of force production via two sets of four, tri-axis, force transducers; one set in the main block and one in the footrest. Data were then analysed, segregating trials for gender. Each start was categorised, with respect to the peak force production in horizontal and vertical components, into one of nine categories. Three performance indicators, i.e. block time, take-off velocity and distance of entry, were used to assess whether differences in performance could be correlated with these categories. Results from these data suggest that swimmers generating higher than average peak forces were more likely to produce a better overall start performance than those who produced forces lower than the average, for this population of athletes.

Development and Evaluation of Elastomeric Materials for Geothermal Applications

NASA Technical Reports Server (NTRS)

Mueller, W. A.; Kalfayan, S. H.; Reilly, W. W.; Yavrouian, A. H.; Mosesman, I. D.; Ingham, J. D.

1979-01-01

A material was formulated having about 250-350 psi tensile strength and 30-80 percent elongation at 260 C for at least 24 hours in simulated brine. The relationship between these laboratory test results and sealing performance in actual or simulated test conditions is not entirely clear; however, it is believed that no conventional formation or casing packer design is likely to perform well using these materials. The synthetic effort focused on high temperature block copolymers and development of curable polystyrene. Procedures were worked out for synthesizing these new materials. Initial results with heat-cured unfilled polystyrene 'gum' at 260 C indicate a tensile strength of about 50 psi. Cast films of the first sample of polyphenyl quinoxaline-polystyrene block copolymer, which has 'graft-block' structure consisting of a polystyrene chain with pendant polyphenyl quinoxaline groups, show elastomeric behavior in the required temperature range. Its tensile strength and elongation at 260 C were 220-350 psi and 18-36 percent, respectively. All of these materials also showed satisfactory hydrolytic stability.

Design and status of the detector block for the ISO-SWS

NASA Technical Reports Server (NTRS)

Luinge, W.; Beintema, D. A.; Haser, L.; Katterloher, R.; Ploeger, G.

1989-01-01

The Short Wave Spectrometer (SWS) is one of the two spectrometers for the Infrared Space Observatory (ISO). It consists of a pair of grating spectrometers and a Fabry-Perot interferometer. Together, the grating spectrometers cover the wavelength range 2.4 to 45 microns, at a resolution between 1000 and 2000. The Fabry-Perot interferometer, in series with one of the grating spectrometers, provides a resolution of about 20,000 at the wavelengths between 15 and 35 microns. The SWS is being built by the Space Research Organization of the Netherlands and the Max Planck Institute for Extraterrestrial Physics in Garching, Germany. The spectrometer has 52 discrete detectors, most of which are bulk detectors. In the design of the spectrometer, the main emphasis is on the sensitivity of the individual channels, rather than on the number of detectors. This was one of the main reasons to select non-destructive read-out circuits, with a separate heated-JFET pre-amplifier for each individual detector. The signals are amplified and filtered in parallel. The engineering tests on the SWS detector block have not yet been completed. The design of the detector block is described and the present problem areas are indicated.

Low cost miniature data collection platform

NASA Technical Reports Server (NTRS)

1977-01-01

The development of the RF elements of a telecommunications package involved detailed study and analysis of concepts and techniques followed by laboratory testing and evaluation of designs. The design goals for a complete telecommunications package excluding antenna were a total weight of 300 grams, in a total volume of 400 cu cm with a capability of unattended operation for a period of six months. Of utmost importance is extremely low cost when produced in lots of 10,000. Early in the program it became apparent that a single Miniature Data Collection Platform would not satisfy all users. A single high efficiency system would not satisfy a user who had available a large battery capacity but required a low cost system. Conversely, the low cost system would not satisfy the end user who had a very limited battery capacity. A system design to satisfy these varied requirements was implemented by designing several versions of the system building blocks and then constructing three systems from these building blocks.

EVALUATION OF BIOREMEDIATION STRATEGIES OF A CONTROLLED OIL RELEASE IN A WETLAND

EPA Science Inventory

A controlled petroleum release was conducted to evaluate bioremediation in a wetland near Houston, Texas. The 140-day study was conducted using a randomized, complete block design to test three treatments with six replicates per treatment. The three treatment strategies were in...

Block 4 solar cell module design and test specification for residential applications

NASA Technical Reports Server (NTRS)

1978-01-01

Near-term design, qualification and acceptance requirements are provided for terrestrial solar cell modules suitable for incorporation in photovoltaic power sources (2 kW to 10 kW) applied to single family residential installations. Requirement levels and recommended design limits for selected performance criteria are specified for modules intended principally for rooftop installations. Modules satisfying the requirements of this specification fall into one of two categories, residential panel or residential shingle, both meeting general performance requirements plus additional category peculiar constraints.

Testing Methods for Integrated Circuit Chips.

DTIC Science & Technology

1986-03-27

DWf <I IAV ~IMi MORY OUT LOGIC~~ IPOGRAM ASYC S’E4i E...* 16o, CO% T ROL CO%TROL 32 Figure 2 . 14 VLSI Tester Block Diagram. registers, memory and test...neral-pIurpos’ processor wi th standard bus- inte-rfaco se-rves as,- th- test control Ii’r and ( 2 ) a c-ustom VLSI test Controller inti-rfacing direc(_t1...Engineering 2 WTWTY ABSTRACT Provision for the functional testing of fabricated VLSI chips frequently involves as much design effort as the orig- _ inal

The Design, Fabrication and Characterization of a Transparent Atom Chip

PubMed Central

Chuang, Ho-Chiao; Huang, Chia-Shiuan; Chen, Hung-Pin; Huang, Chi-Sheng; Lin, Yu-Hsin

2014-01-01

This study describes the design and fabrication of transparent atom chips for atomic physics experiments. A fabrication process was developed to define the wire patterns on a transparent glass substrate to create the desired magnetic field for atom trapping experiments. An area on the chip was reserved for the optical access, so that the laser light can penetrate directly through the glass substrate for the laser cooling process. Furthermore, since the thermal conductivity of the glass substrate is poorer than other common materials for atom chip substrate, for example silicon, silicon carbide, aluminum nitride. Thus, heat dissipation copper blocks are designed on the front and back of the glass substrate to improve the electrical current conduction. The testing results showed that a maximum burnout current of 2 A was measured from the wire pattern (with a width of 100 μm and a height of 20 μm) without any heat dissipation design and it can increase to 2.5 A with a heat dissipation design on the front side of the atom chips. Therefore, heat dissipation copper blocks were designed and fabricated on the back of the glass substrate just under the wire patterns which increases the maximum burnout current to 4.5 A. Moreover, a maximum burnout current of 6 A was achieved when the entire backside glass substrate was recessed and a thicker copper block was electroplated, which meets most requirements of atomic physics experiments. PMID:24922456

Optimizing Balanced Incomplete Block Designs for Educational Assessments

ERIC Educational Resources Information Center

van der Linden, Wim J.; Veldkamp, Bernard P.; Carlson, James E.

2004-01-01

A popular design in large-scale educational assessments as well as any other type of survey is the balanced incomplete block design. The design is based on an item pool split into a set of blocks of items that are assigned to sets of "assessment booklets." This article shows how the problem of calculating an optimal balanced incomplete block…

78 FR 49334 - Designation of 5 individual(s) and 2 entity(-ies) Pursuant to Executive Order 13581, “Blocking...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-13

... entity(-ies) Pursuant to Executive Order 13581, ``Blocking Property of Transnational Criminal... July 24, 2011, ``Blocking Property of Transnational Criminal Organizations.'' DATES: The designations... President issued Executive Order 13581, ``Blocking Property of Transnational Criminal Organizations'' (the...

Design and Synthesis of Novel Block Copolymers for Efficient Opto-Electronic Applications

NASA Technical Reports Server (NTRS)

Sun, Sam-Shajing; Fan, Zhen; Wang, Yiqing; Taft, Charles; Haliburton, James; Maaref, Shahin

2002-01-01

It has been predicted that nano-phase separated block copolymer systems containing electron rich donor blocks and electron deficient acceptor blocks may facilitate the charge carrier separation and migration in organic photovoltaic devices due to improved morphology in comparison to polymer blend system. This paper presents preliminary data describing the design and synthesis of a novel Donor-Bridge-Acceptor (D-B-A) block copolymer system for potential high efficient organic optoelectronic applications. Specifically, the donor block contains an electron donating alkyloxy derivatized polyphenylenevinylene (PPV), the acceptor block contains an electron withdrawing alkyl-sulfone derivatized polyphenylenevinylene (PPV), and the bridge block contains an electronically neutral non-conjugated aliphatic hydrocarbon chain. The key synthetic strategy includes the synthesis of each individual block first, then couple the blocks together. While the donor block stabilizes and facilitates the transport of the holes, the acceptor block stabilizes and facilitates the transport of the electrons, the bridge block is designed to hinder the probability of electron-hole recombination. Thus, improved charge separation and stability are expected with this system. In addition, charge migration toward electrodes may also be facilitated due to the potential nano-phase separated and highly ordered block copolymer ultra-structure.

The feasibility of implementing recovery, psychosocial and pharmacological interventions for psychosis: comparison study.

PubMed

van der Krieke, Lian; Bird, Victoria; Leamy, Mary; Bacon, Faye; Dunn, Rebecca; Pesola, Francesca; Janosik, Monika; Le Boutillier, Clair; Williams, Julie; Slade, Mike

2015-05-23

Clinical guidelines for the treatment of people experiencing psychosis have existed for over a decade, but implementation of recommended interventions is limited. Identifying influences on implementation may help to reduce this translational gap. The Structured Assessment of Feasibility (SAFE) measure is a standardised assessment of implementation blocks and enablers. The aim of this study was to characterise and compare the implementation blocks and enablers for recommended psychosis interventions. SAFE was used to evaluate and compare three groups of interventions recommended in the 2014 NICE psychosis guideline: pharmacological (43 trials testing 5 interventions), psychosocial (65 trials testing 5 interventions), and recovery (19 trials testing 5 interventions). The 127 trial reports rated with SAFE were supplemented by published intervention manuals, research protocols, trial registrations and design papers. Differences in the number of blocks and enablers across the three interventions were tested statistically, and feasibility profiles were generated. There was no difference between psychosocial and recovery interventions in the number of blocks or enablers to implementation. Pharmacological interventions (a) had fewer blocks than both psychosocial interventions (χ (2)(3) = 133.77, p < 0.001) and recovery interventions (χ (2)(3) = 104.67, p < 0.001) and (b) did not differ in number of enablers from recovery interventions (χ (2)(3) = 0.74, p = 0.863) but had fewer enablers than psychosocial interventions (χ (2)(3) = 28.92, p < 0.001). Potential adverse events associated with the intervention tend to be a block for pharmacological interventions, whereas complexity of the intervention was the most consistent block for recovery and psychosocial interventions. Feasibility profiles show that pharmacological interventions are relatively easy to implement but can sometimes involve risks. Psychosocial and recovery interventions are relatively complex but tend to be more flexible and more often manualised. SAFE ratings can contribute to tackling the current implementation challenges in mental health services, by providing a reporting guideline structure for researchers to maximise the potential for implementation and by informing prioritisation decisions by clinical guideline developers and service managers.

Visuo-spatial performance in autism: a meta-analysis.

PubMed

Muth, Anne; Hönekopp, Johannes; Falter, Christine M

2014-12-01

Visuo-spatial skills are believed to be enhanced in autism spectrum disorders (ASDs). This meta-analysis tests the current state of evidence for Figure Disembedding, Block Design, Mental Rotation and Navon tasks in ASD and neurotypicals. Block Design (d = 0.32) and Figure Disembedding (d = 0.26) showed superior performance for ASD with large heterogeneity that is unaccounted for. No clear differences were found for Mental Rotation. ASD samples showed a stronger local processing preference for Navon tasks (d = 0.35); less clear evidence for performance differences of a similar magnitude emerged. We discuss the meta-analysis results together with other findings relating to visuo-spatial processing and three cognitive theories of ASD: Weak Central Coherence, Enhanced Perceptual Functioning and Extreme Male Brain theory.

Software reliability through fault-avoidance and fault-tolerance

NASA Technical Reports Server (NTRS)

Vouk, Mladen A.; Mcallister, David F.

1992-01-01

Accomplishments in the following research areas are summarized: structure based testing, reliability growth, and design testability with risk evaluation; reliability growth models and software risk management; and evaluation of consensus voting, consensus recovery block, and acceptance voting. Four papers generated during the reporting period are included as appendices.

Properties Of Carbon/Carbon and Carbon/Phenolic Composites

NASA Technical Reports Server (NTRS)

Mathis, John R.; Canfield, A. R.

1993-01-01

Report presents data on physical properties of carbon-fiber-reinforced carbon-matrix and phenolic-matrix composite materials. Based on tests conducted on panels, cylinders, blocks, and formed parts. Data used by designers to analyze thermal-response and stress levels and develop structural systems ensuring high reliability at minimum weight.

Multiple Learning Strategies Project. Small Engine Repair. Visually Impaired.

ERIC Educational Resources Information Center

Foster, Don; And Others

This instructional package designed for visually impaired students, focuses on the vocational area of small engine repair. Contained in this document are forty learning modules organized into fourteen units: engine block; starters; fuel tank, lines, filters and pumps; carburetors; electrical; test equipment; motorcycle; machining; tune-ups; short…

Multiple Learning Strategies Project. Medical Assistant. Visually Impaired. [Vol. 1.

ERIC Educational Resources Information Center

Varney, Beverly; And Others

This instructional package, one of two designed for visually impaired students, focuses on the vocational area of medical assistant. Contained in this document are twelve learning modules organized into five units: language; receptioning; asepsis; supplies and equipment maintenance; and diagnostic tests. Each module, printed in block type,…

Door Hardware and Installations; Carpentry: 901894.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The curriculum guide outlines a course designed to provide instruction in the selection, preparation, and installation of hardware for door assemblies. The course is divided into five blocks of instruction (introduction to doors and hardware, door hardware, exterior doors and jambs, interior doors and jambs, and a quinmester post-test) totaling…

New Directions in Maintenance Simulation.

ERIC Educational Resources Information Center

Miller, Gary G.

A two-phase effort was conducted to design and evaluate a maintenance simulator which incorporated state-of-the-art information in simulation and instructional technology. The particular equipment selected to be simulated was the 6883 Convert/Flight Controls Test Station. Phase I included a generalized block diagram of the computer-trainer, the…

Microbial Fouling and its Effect on Power Generation.

DTIC Science & Technology

1981-09-01

The tubular fouling reactor system (TFR) consists of a test block heat exchanger and a support system which includes water supply treatment facilities...and measurement instrumentation. Figure 8 is a schematic diagram of the system. Test block heat exchanger : The test block heat exchanger consists of...two adjacent aluminum cylindrical blocks (12.5 cm dia.) clamped to the section of tubing being tested (Fig. 9). The block is heated by electrical re

The Function Acquisition Speed Test (FAST): A Behavior Analytic Implicit Test for Assessing Stimulus Relations

ERIC Educational Resources Information Center

O'Reilly, Anthony; Roche, Bryan; Ruiz, Maria; Tyndall, Ian; Gavin, Amanda

2012-01-01

Subjects completed a baseline stimulus matching procedure designed to produce two symmetrical stimulus relations; A1-B1 and A2-B2. Using A1, B1, and two novel stimuli, subjects were then trained to produce a common key-press response for two stimuli and a second key-press response for two further stimuli across two blocks of response training.…

Non-Pilot Protection of the HVDC Grid

NASA Astrophysics Data System (ADS)

Badrkhani Ajaei, Firouz

This thesis develops a non-pilot protection system for the next generation power transmission system, the High-Voltage Direct Current (HVDC) grid. The HVDC grid protection system is required to be (i) adequately fast to prevent damages and/or converter blocking and (ii) reliable to minimize the impacts of faults. This study is mainly focused on the Modular Multilevel Converter (MMC) -based HVDC grid since the MMC is considered as the building block of the future HVDC systems. The studies reported in this thesis include (i) developing an enhanced equivalent model of the MMC to enable accurate representation of its DC-side fault response, (ii) developing a realistic HVDC-AC test system that includes a five-terminal MMC-based HVDC grid embedded in a large interconnected AC network, (iii) investigating the transient response of the developed test system to AC-side and DC-side disturbances in order to determine the HVDC grid protection requirements, (iv) investigating the fault surge propagation in the HVDC grid to determine the impacts of the DC-side fault location on the measured signals at each relay location, (v) designing a protection algorithm that detects and locates DC-side faults reliably and sufficiently fast to prevent relay malfunction and unnecessary blocking of the converters, and (vi) performing hardware-in-the-loop tests on the designed relay to verify its potential to be implemented in hardware. The results of the off-line time domain transients studies in the PSCAD software platform and the real-time hardware-in-the-loop tests using an enhanced version of the RTDS platform indicate that the developed HVDC grid relay meets all technical requirements including speed, dependability, security, selectivity, and robustness. Moreover, the developed protection algorithm does not impose considerable computational burden on the hardware.

Preliminary design of an intermittent smoke flow visualization system

NASA Technical Reports Server (NTRS)

Ward, Donald T.; Myatt, James H.

1993-01-01

A prototype intermittent flow visualization system that was designed to study vortex flow field dynamics has been constructed and tested through its ground test phase. It produces discrete pulses of dense white smoke consisting of particles of terephthalic acid by the pulsing action of a fast-acting three-way valve. The trajectories of the smoke pulses can be tracked by a video imaging system without intruding in the flow around in flight. Two methods of pulsing the smoke were examined. The simplest and safest approach is to simply divert the smoke between the two outlet ports on the valve; this approach should be particularly effective if it were desired to inject smoke at two locations during the same test event. The second approach involves closing off one of the outlet ports to momentarily block the flow. The second approach requires careful control of valve dwell times to avoid excessive pressure buildup within the cartridge container. This method also increases the velocity of the smoke injected into the flow. The flow of the smoke has been blocked for periods ranging from 30 to 80 milliseconds, depending on the system volume and the length of time the valve is allowed to remain open between valve closings.

The DARHT Phase 2 Linac

DOE Office of Scientific and Technical Information (OSTI.GOV)

wolf, Zachary R.

2000-09-12

The second phase accelerator for the Dual Axis Hydrodynamic Test facility (DARHT) is designed to provide an electron beam pulse that is 2{mu}s long, 2kA, and 20 MeV in particle energy. The injector provides 3.2 MeV so that the linac need only provide 16.8 MeV. The linac is made with two types of induction accelerator cells. The first block of 8 cells have a 14 in. beam pipe compared to 10 in. in the remaining 80 cells. The other principal difference is that the first 8 cells have reduced volt-sec in their induction cores as a result of a largermore » diameter beam pipe. The cells are designed for very reliable high voltage operation. The insulator is Mycalex. Results from prototype tests are given including results from solenoid measurements. Each cell contains a solenoid for beam transport and a set of x-y correction coils to reduce corkscrew motion. Details of tests to determine RF mode impedances relevant to BBU generation are given. Blocks of cells are separated by intercells some of which contain transport solenoids. The intercells provide vacuum pumping stations as well. Issues of alignment and installation are discussed.« less

A Design Selection Procedure.

ERIC Educational Resources Information Center

Kroeker, Leonard P.

The problem of blocking on a status variable was investigated. The one-way fixed-effects analysis of variance, analysis of covariance, and generalized randomized block designs each treat the blocking problem in a different way. In order to compare these designs, it is necessary to restrict attention to experimental situations in which observations…

Wechsler Adult Intelligence Scale-Revised Block Design broken configuration errors in nonpenetrating traumatic brain injury.

PubMed

Wilde, M C; Boake, C; Sherer, M

2000-01-01

Final broken configuration errors on the Wechsler Adult Intelligence Scale-Revised (WAIS-R; Wechsler, 1981) Block Design subtest were examined in 50 moderate and severe nonpenetrating traumatically brain injured adults. Patients were divided into left (n = 15) and right hemisphere (n = 19) groups based on a history of unilateral craniotomy for treatment of an intracranial lesion and were compared to a group with diffuse or negative brain CT scan findings and no history of neurosurgery (n = 16). The percentage of final broken configuration errors was related to injury severity, Benton Visual Form Discrimination Test (VFD; Benton, Hamsher, Varney, & Spreen, 1983) total score and the number of VFD rotation and peripheral errors. The percentage of final broken configuration errors was higher in the patients with right craniotomies than in the left or no craniotomy groups, which did not differ. Broken configuration errors did not occur more frequently on designs without an embedded grid pattern. Right craniotomy patients did not show a greater percentage of broken configuration errors on nongrid designs as compared to grid designs.

Thermohydrologic modeling of the large-block test in partially saturated fractured tuff at Yucca Mountain, Nevada

NASA Astrophysics Data System (ADS)

Lee, K.; Buscheck, T. A.; Glascoe, L. G.; Gansemer, J.; Sun, Y.

2002-12-01

In support of the characterization of Yucca Mountain as a potential site for as a geologic repository for high-level nuclear waste, the US Department of Energy conducted the Large Block Test (LBT) at nearby Fran Ridge. The LBT was conducted in an excavated 3x 3x 4.5m block of partially saturated, fractured nonlithophysal Topopah Spring tuff, which is one of the host-rock units for the potential repository at Yucca Mountain. The LBT was one of a series of field-scale thermohydrologic tests conducted in the repository host-rock units. The LBT was heated by line heaters installed in five boreholes lying in a horizontal plane 2.75 m below the upper surface of the block. The field-scale thermal tests were designed to help investigators better understand the coupled thermohydrologic-mechanical-chemical processes that would occur in the host rock in response to the radioactive heat of decay from emplaced waste packages. The tests also provide data for the calibration and validation of numerical models used to analyze the thermohydrologic response of the near-field host rock and Engineered Barrier System (EBS). Using the NUFT code and the dual-permeability approach to representing fracture-matrix interaction, we simulated the thermohydrologic response of the block to a heating and cooling cycle. The primary goals of the analysis were to study the heat-flow mechanisms and water redistribution patterns in the boiling and sub-boiling zones, and to compare model results with measured temperature and liquid saturation data, and thereby evaluate two rock property data sets available for modeling thermohydrologic behavior in the rock. Model results were also used for model calibration and validation. We obtained a good to excellent match between model and observed temperatures, and found that the distinct dryout and condensation zones modeled above and below the heater level agreed fairly well with the liquid-saturation measurements. We identified the best-fit data set by using a statistical analysis to compare model and field temperatures, and found that heat flow in the block was dominated by conduction.

Optimization of fly ash and bottom ash substitution against paving block manufacture according to SNI 03-0691-1996

NASA Astrophysics Data System (ADS)

Karolina, R.; Syahrizal; Bahri, N.

2018-02-01

The waste of coal burning has a very negative impact on the environment if the waste is not managed as well as possible. The remaining waste of coal combustion consists of fly ash and bottom ash. FA and BA can be developed into substitution materials in the process of making paving blocks. The purpose of this study was to determine the quality of paving block in accordance with SK SNI 03-0691-1996 with optimization in the use of FA and BA. This study uses a 351 paving block sample size of 20x10x6 cm. Paving blocks are divided by 4 categories, namely normal paving block, paving block with FA substitution, BA substitution and combination of FA-BA with each variation 0%, 25%, 50%, 75% and 100%. Each variation amounted to 27 samples. Paving block quality measurement is done through 4 tests: absorption, compressive strength, sodium sulphate resistance and Los Angeles tests. The result of the test shows the absorption of normal paving block is 3,229%, paving block with 25% FA is 3,889%, paving block with 50% BA is 5,560% and paving block with 25% FA-BA combination is 5,794%. Compressive strength in normal paving block is 25,50 MPa, paving block with 25% FA is 25,28 MPa, paving block with 25% BA is equal to 27,61 MPa and paving block with 25% FA-BA is 26, 00 MPa. In testing of sodium sulfate resistance, almost all test specimens are eligible except for paving block with 50% FA and 75% FA. In the test of wear resistance, no specimen is eligible according to SK SNI 03-0691-1996. The comparison of the strength of the test specimen can be seen in substitution with 25% BA which reaches maximum strength.

Test Results from a High Power Linear Alternator Test Rig

NASA Technical Reports Server (NTRS)

Birchenough, Arthur G.; Hervol, David S.; Gardner, Brent G.

2010-01-01

Stirling cycle power conversion is an enabling technology that provides high thermodynamic efficiency but also presents unique challenges with regard to electrical power generation, management, and distribution. The High Power Linear Alternator Test Rig (HPLATR) located at the NASA Glenn Research Center (GRC) in Cleveland, OH is a demonstration test bed that simulates electrical power generation from a Stirling engine driven alternator. It implements the high power electronics necessary to provide a well regulated DC user load bus. These power electronics use a novel design solution that includes active rectification and power factor control, active ripple suppression, along with a unique building block approach that permits the use of high voltage or high current alternator designs. This presentation describes the HPLATR, the test program, and the operational results.

Test Results From a High Power Linear Alternator Test Rig

NASA Technical Reports Server (NTRS)

Birchenough, Arthur G.; Hervol, David S.; Gardner, Brent G.

2010-01-01

Stirling cycle power conversion is an enabling technology that provides high thermodynamic efficiency but also presents unique challenges with regard to electrical power generation, management, and distribution. The High Power Linear Alternator Test Rig (HPLATR) located at the NASA Glenn Research Center (GRC) in Cleveland, Ohio is a demonstration test bed that simulates electrical power generation from a Stirling engine driven alternator. It implements the high power electronics necessary to provide a well regulated DC user load bus. These power electronics use a novel design solution that includes active rectification and power factor control, active ripple suppression, along with a unique building block approach that permits the use of high voltage or high current alternator designs. This report describes the HPLATR, the test program, and the operational results.

Design of an MR image processing module on an FPGA chip

NASA Astrophysics Data System (ADS)

Li, Limin; Wyrwicz, Alice M.

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments.

Design of an MR image processing module on an FPGA chip

PubMed Central

Li, Limin; Wyrwicz, Alice M.

2015-01-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. PMID:25909646

Saturn Apollo Program

NASA Image and Video Library

1960-01-01

This photograph shows the Saturn-I first stage (S-1 stage) being transported to the test stand for a static test firing at the Marshall Space Flight Center. Soon after NASA began operations in October 1958, it was evident that sending people and substantial equipment beyond the Earth's gravitational field would require launch vehicles with weight-lifting capabilities far beyond any developed to that time. In early 1959, NASA accepted the proposal of Dr. Wernher von Braun for a multistage rocket, with a number of engines clustered in one or more of the stages to provide a large total thrust. The initiation of the Saturn launch vehicle program ultimately led to the study and preliminary plarning of many different configurations and resulted in production of three Saturn launch vehicles, the Saturn-I, Saturn I-B, and Saturn V. The Saturn family of launch vehicles began with the Saturn-I, a two-stage vehicle originally designated C-1. The research and development program was planned in two phases, or blocks: one for first stage development (Block I) and the second for both first and second stage development (Block-II). Saturn I had a low-earth-orbit payload capability of approximately 25,000 pounds. The design of the first stage (S-1 stage) used a cluster of propellant tanks containing liquid oxygen (LOX) and kerosene (RP-1), and eight H-1 engines, yielding a total thrust of 1,500,000 pounds. Of the ten Saturn-Is planned, the first eight were designed and built at the Marshall Space Flight Center, and the remaining two were built by the Chrysler Corporation.

Structured programming: Principles, notation, procedure

NASA Technical Reports Server (NTRS)

JOST

1978-01-01

Structured programs are best represented using a notation which gives a clear representation of the block encapsulation. In this report, a set of symbols which can be used until binding directives are republished is suggested. Structured programming also allows a new method of procedure for design and testing. Programs can be designed top down, that is, they can start at the highest program plane and can penetrate to the lowest plane by step-wise refinements. The testing methodology also is adapted to this procedure. First, the highest program plane is tested, and the programs which are not yet finished in the next lower plane are represented by so-called dummies. They are gradually replaced by the real programs.

Evaluation of transfer films of Salox M on 440C for HPOTP bearing cage applications, task 119

NASA Technical Reports Server (NTRS)

Barber, S. A.; Kannel, J. W.; Dufrane, K. F.

1986-01-01

The objective of the task was to evaluate the suitability of a bronze-filled polytetra fluoroethylene (Salox M) as the cage material in Space Shuttle Main Engine (SSME) high pressure oxygen turbo pump (HPOTP) bearings. The role of the cage pocket material will be to provide a transferred lubricating interface at the ball-race contact region. A series of experiments was conducted which involved block-on-ring tests (the block was the polytetrafluoroethylene (PTFE) -filled material and the ring was through-hardened 440C steel) and high speed traction tests of two 440C disks with one disk rubbed with a PTFE block to generate a transfer film. Measurements included post test visual observations of the condition of the 440C, wear rate measurements of the blocks, and traction measurements between the disks. It was observed that both Salox M and glass-filled PTFE (Armalon) transferred PTFE to 440C at cryogenic temperatures. Bronze is also transferred to uncoated 440C from the Salox M. At room temperature no PTFE transfer was observed in the high speed disk tests due to severe frictional heating, although bronze transfer still occurred with the bronze-PTFE Salox M material. Since the bearing will operate at cryogenic temperature, transfer films are very probable. Salox M wore slightly, although probably tolerably, more than glass-filled PTFE against 440C. However, Salox M is clearly less abrasive to 440C than is the glass-filled material. When the surface layer of PTFE is depleted from the glass-filled material, the glass fibers tend to seriously abrade the steel. This problem does not occur with Salox M. The surface roughness studies indicate that smooth balls are quite reasonable for transfer films. No significant difference in wear rates of the candidate cage materials was observed when the 440C surface finish was increased from 0.025 micron to 0.1 micron cla. At higher levels of roughness, the wear rate increased. Two surface coatings (MoS2 and TiN) were tested. The surface coatings tended to reduce the Salox M wear rate and reduce bronze transfer. PTFE transfer at cryogenic temperatures still occurred with the surface coatings. Two cage design concepts are presented utilizing Salox M material. One design involves a metal-reinforced Salox M cage, while the second design uses Salox M inserts in a metal structure.

Apollo experience report guidance and control systems: Primary guidance, navigation, and control system development

NASA Technical Reports Server (NTRS)

Holley, M. D.; Swingle, W. L.; Bachman, S. L.; Leblanc, C. J.; Howard, H. T.; Biggs, H. M.

1976-01-01

The primary guidance, navigation, and control systems for both the lunar module and the command module are described. Development of the Apollo primary guidance systems is traced from adaptation of the Polaris Mark II system through evolution from Block I to Block II configurations; the discussion includes design concepts used, test and qualification programs performed, and major problems encountered. The major subsystems (inertial, computer, and optical) are covered. Separate sections on the inertial components (gyroscopes and accelerometers) are presented because these components represent a major contribution to the success of the primary guidance, navigation, and control system.

Evaluation of Nonlinear Constitutive Properties of Concrete

DTIC Science & Technology

1990-02-01

34 " \\ 19:#BSTRACT (Continue on reverse if necesuar 4nd identify by block number) 3his report describes the development of a methodology that allows for...Continued). The method of evaluation, as developed herein, consists of the following steps: 1. The design and execution of a series of material... developed in Step L. 3. Design and execution of the series of verification tests which provide data suffi- cient for defining key complex material

Compact Receiver Front Ends for Submillimeter-Wave Applications

NASA Technical Reports Server (NTRS)

Mehdi, Imran; Chattopadhyay, Goutam; Schlecht, Erich T.; Lin, Robert H.; Sin, Seth; Peralta, Alejandro; Lee, Choonsup; Gill, John J.; Gulkis, Samuel; Thomas, Bertrand C.

2012-01-01

The current generation of submillimeter-wave instruments is relatively mass and power-hungry. The receiver front ends (RFEs) of a submillimeter instrument form the heart of the instrument, and any mass reduction achieved in this subsystem is propagated through the instrument. In the current implementation, the RFE consists of different blocks for the mixer and LO circuits. The motivation for this work is to reduce the mass of the RFE by integrating the mixer and LO circuits in one waveguide block. The mixer and its associated LO chips will all be packaged in a single waveguide package. This will reduce the mass of the RFE and also provide a number of other advantages. By bringing the mixer and LO circuits close together, losses in the waveguide will be reduced. Moreover, the compact nature of the block will allow for better thermal control of the block, which is important in order to reduce gain fluctuations. A single waveguide block with a 600- GHz RFE functionality (based on a subharmonically pumped Schottky diode pair) has been demonstrated. The block is about 3x3x3 cubic centimeters. The block combines the mixer and multiplier chip in a single package. 3D electromagnetic simulations were carried out to design the waveguide circuit around the mixer and multiplier chip. The circuit is optimized to provide maximum output power and maximum bandwidth. An integrated submillimeter front end featuring a 520-600-GHz sub-harmonic mixer and a 260-300-GHz frequency tripler in a single cavity was tested. Both devices used GaAs MMIC membrane planar Schottky diode technology. The sub-harmonic mixer/tripler circuit has been tested using conventional metal-machined blocks. Measurement results on the metal block give best DSB (double sideband) mixer noise temperature of 2,360 K and conversion losses of 7.7 dB at 520 GHz. The LO input power required to pump the integrated tripler/sub-harmonic mixer is between 30 and 50 mW.

Shielding analyses for repetitive high energy pulsed power accelerators

NASA Astrophysics Data System (ADS)

Jow, H. N.; Rao, D. V.

Sandia National Laboratories (SNL) designs, tests and operates a variety of accelerators that generate large amounts of high energy Bremsstrahlung radiation over an extended time. Typically, groups of similar accelerators are housed in a large building that is inaccessible to the general public. To facilitate independent operation of each accelerator, test cells are constructed around each accelerator to shield it from the radiation workers occupying surrounding test cells and work-areas. These test cells, about 9 ft. high, are constructed of high density concrete block walls that provide direct radiation shielding. Above the target areas (radiation sources), lead or steel plates are used to minimize skyshine radiation. Space, accessibility and cost considerations impose certain restrictions on the design of these test cells. SNL Health Physics division is tasked to evaluate the adequacy of each test cell design and compare resultant dose rates with the design criteria stated in DOE Order 5480.11. In response, SNL Health Physics has undertaken an intensive effort to assess existing radiation shielding codes and compare their predictions against measured dose rates. This paper provides a summary of the effort and its results.

Superconducting-electromagnetic hybrid bearing using YBCO bulk blocks for passive axial levitation

NASA Astrophysics Data System (ADS)

Nicolsky, R.; de Andrade, R., Jr.; Ripper, A.; David, D. F. B.; Santisteban, J. A.; Stephan, R. M.; Gawalek, W.; Habisreuther, T.; Strasser, T.

2000-06-01

A superconducting/electromagnetic hybrid bearing has been designed using active radial electromagnetic positioning and a superconducting passive axial levitator. This bearing has been tested for an induction machine with a vertical shaft. The prototype was conceived as a four-pole, two-phase induction machine using specially designed stator windings for delivering torque and radial positioning simultaneously. The radial bearing uses four eddy-current sensors, displaced 90° from each other, for measuring the shaft position and a PID control system for feeding back the currents. The stator windings have been adapted from the ones of a standard induction motor. The superconducting axial bearing has been assembled with commercial NdFeB permanent magnets and a set of seven top-seeded-melt-textured YBCO large-grain cylindrical blocks. The bearing set-up was previously simulated by a finite element method for different permanent magnet-superconductor block configurations. The stiffness of the superconducting axial bearing has been investigated by measuring by a dynamic method the vertical and transversal elastic constants for different field cooling processes. The resulting elastic constants show a linear dependence on the air gap, i.e. the clearance between the permanent magnet assembly and the set of superconducting large-grain blocks, which is dependent on cooling distance.

Microleakage of composite crowns luted on CAD/CAM-milled human molars: a new method for standardized in vitro tests.

PubMed

Schlenz, Maximiliane Amelie; Schmidt, Alexander; Rehmann, Peter; Niem, Thomas; Wöstmann, Bernd

2018-04-24

To investigate debonding of full crowns made of CAD/CAM composites, CAD/CAM technology was applied to manufacture standardized test abutments to increase the reproducibility of human teeth used in in vitro studies. A virtual test abutment and the corresponding virtual crown were designed and two STL data sets were generated. Sixty-four human third molars and CAD/CAM blocks were milled using a CNC machine. Crowns of four different composite blocks (Lava Ultimate (LU), Brilliant Crios (BC), Cerasmart (CS), Experimental (EX)) were adhesively bonded with their corresponding luting system (LU: Scotchbond Universal/RelyX Ultimate; BC: One Coat 7 Universal/DuoCem; CS: G-PremioBond/G-Cem LinkForce; EX: Experimental-Bond/Experimental-Luting-Cement). Half of the specimens were chemical-cured (CC) and the others were light-cured (LC). Afterwards, specimens were artificially aged in a chewing simulator (WL-tec, 1 million cycles, 50-500 N, 2 Hz, 37 °C). Finally, a dye penetration test was used to detect debonding. For inspection, the specimens were sliced, and penetration depth was measured with a digital microscope. Data were analyzed with the Mann-Whitney U test. No cases of total debonding were observed after cyclic loading. However, the LC specimens showed a significantly lower amount of leakage than the CC ones (p < 0.05). Furthermore, the CC specimens exhibited broad scattering. Only the LC-EX blocks showed no debonding. The CC-CS blocks showed the highest leakage and scattering of all tested specimens. Natural human teeth can be manufactured by CAD/CAM technology in highly standardized test abutments for in vitro testing. For CAD/CAM composites, light curing should be performed. The success of a restoration depends on the long-term sealing ability of the luting materials, which avoids debonding along with microleakage. For CAD/CAM composites, separate light curing of the adhesive and luting composite is highly recommended.

Area, speed and power measurements of FPGA-based complex orthogonal space-time block code channel encoders

NASA Astrophysics Data System (ADS)

Passas, Georgios; Freear, Steven; Fawcett, Darren

2010-01-01

Space-time coding (STC) is an important milestone in modern wireless communications. In this technique, more copies of the same signal are transmitted through different antennas (space) and different symbol periods (time), to improve the robustness of a wireless system by increasing its diversity gain. STCs are channel coding algorithms that can be readily implemented on a field programmable gate array (FPGA) device. This work provides some figures for the amount of required FPGA hardware resources, the speed that the algorithms can operate and the power consumption requirements of a space-time block code (STBC) encoder. Seven encoder very high-speed integrated circuit hardware description language (VHDL) designs have been coded, synthesised and tested. Each design realises a complex orthogonal space-time block code with a different transmission matrix. All VHDL designs are parameterisable in terms of sample precision. Precisions ranging from 4 bits to 32 bits have been synthesised. Alamouti's STBC encoder design [Alamouti, S.M. (1998), 'A Simple Transmit Diversity Technique for Wireless Communications', IEEE Journal on Selected Areas in Communications, 16:55-108.] proved to be the best trade-off, since it is on average 3.2 times smaller, 1.5 times faster and requires slightly less power than the next best trade-off in the comparison, which is a 3/4-rate full-diversity 3Tx-antenna STBC.

Comparison of the Pullout Strength of Different Pedicle Screw Designs and Augmentation Techniques in an Osteoporotic Bone Model.

PubMed

Kiyak, Gorkem; Balikci, Tevfik; Heydar, Ahmed Majid; Bezer, Murat

2018-02-01

Mechanical study. To compare the pullout strength of different screw designs and augmentation techniques in an osteoporotic bone model. Adequate bone screw pullout strength is a common problem among osteoporotic patients. Various screw designs and augmentation techniques have been developed to improve the biomechanical characteristics of the bone-screw interface. Polyurethane blocks were used to mimic human osteoporotic cancellous bone, and six different screw designs were tested. Five standard and expandable screws without augmentation, eight expandable screws with polymethylmethacrylate (PMMA) or calcium phosphate augmentation, and distal cannulated screws with PMMA and calcium phosphate augmentation were tested. Mechanical tests were performed on 10 unused new screws of each group. Screws with or without augmentation were inserted in a block that was held in a fixture frame, and a longitudinal extraction force was applied to the screw head at a loading rate of 5 mm/min. Maximum load was recorded in a load displacement curve. The peak pullout force of all tested screws with or without augmentation was significantly greater than that of the standard pedicle screw. The greatest pullout force was observed with 40-mm expandable pedicle screws with four fins and PMMA augmentation. Augmented distal cannulated screws did not have a greater peak pullout force than nonaugmented expandable screws. PMMA augmentation provided a greater peak pullout force than calcium phosphate augmentation. Expandable pedicle screws had greater peak pullout forces than standard pedicle screws and had the advantage of augmentation with either PMMA or calcium phosphate cement. Although calcium phosphate cement is biodegradable, osteoconductive, and nonexothermic, PMMA provided a significantly greater peak pullout force. PMMA-augmented expandable 40-mm four-fin pedicle screws had the greatest peak pullout force.

The effect of Fisher information matrix approximation methods in population optimal design calculations.

PubMed

Strömberg, Eric A; Nyberg, Joakim; Hooker, Andrew C

2016-12-01

With the increasing popularity of optimal design in drug development it is important to understand how the approximations and implementations of the Fisher information matrix (FIM) affect the resulting optimal designs. The aim of this work was to investigate the impact on design performance when using two common approximations to the population model and the full or block-diagonal FIM implementations for optimization of sampling points. Sampling schedules for two example experiments based on population models were optimized using the FO and FOCE approximations and the full and block-diagonal FIM implementations. The number of support points was compared between the designs for each example experiment. The performance of these designs based on simulation/estimations was investigated by computing bias of the parameters as well as through the use of an empirical D-criterion confidence interval. Simulations were performed when the design was computed with the true parameter values as well as with misspecified parameter values. The FOCE approximation and the Full FIM implementation yielded designs with more support points and less clustering of sample points than designs optimized with the FO approximation and the block-diagonal implementation. The D-criterion confidence intervals showed no performance differences between the full and block diagonal FIM optimal designs when assuming true parameter values. However, the FO approximated block-reduced FIM designs had higher bias than the other designs. When assuming parameter misspecification in the design evaluation, the FO Full FIM optimal design was superior to the FO block-diagonal FIM design in both of the examples.

Proximal Interphalangeal Joint Extension Block Splint

PubMed Central

Abboudi, Jack; Jones, Christopher M.

2016-01-01

Background: Extension block splinting of the proximal interphalangeal (PIP) joint is a simple and useful treatment option although the practical application of this technique has remained undefined in the literature. Methods: This article provides a step-by-step technique for the construction of a reliable PIP extension block splint and also reviews basic indications for treatment with a PIP extension block splint as well as other PIP extension block splint designs. Results: The proposed splint design outlined in this article is reliable, easy to reproduce and easy for patients to manage when treated with a PIP extension block splint. Conclusions: PIP extension block splinting has a role for certain injuries and certain post-operative protocols. A reliable splint design that is easy to manage makes this treatment choice more attractive to the surgeon and the patient. PMID:27390555

Chemical Modification and Structure-property Relationships of Acrylic and Ionomeric Thermoplastic Elastomer Gels

NASA Astrophysics Data System (ADS)

Vargantwar, Pruthesh Hariharrao

Block copolymers (BCs) have remained at the forefront of materials research due to their versatility in applications ranging from hot-melt/pressure-sensitive adhesives and impact modifiers to compatibilizing agents and vibration-dampening/nanotemplating media. Of particular interest are macromolecules composed of two or more chemically dissimilar blocks covalently linked together to form triblock or pentablock copolymers. If the blocks are sufficiently incompatible and the copolymer behaves as a thermoplastic elastomer, the molecules can spontaneously self-assemble to form nanostructured materials that exhibit shape memory due to the formation of a supramolecular network. The BCs of these types are termed as conventional. When BCs contain blocks having ionic moieties such as sulfonic acid groups, they are termed as block ionomers. Designing new systems based on either conventional or ionic BCs, characterizing their structure-property relationships and later using them as electroacive polymers form the essential objectives of this work. Electroactive polymers (EAPs) exhibit electromechanical actuation when stimulated by an external electric field. In the first part of this work, it is shown that BCs resolve some of the outstanding problems presently encountered in the design of two different classes of EAP actuators: dielectric elastomers (DEs) and ionic polymer metal composites (IPMCs). All-acrylic triblock copolymer gels used as DEs actuate with high efficacy without any requirement of mechanical prestrain and, thus, eliminate the need for bulky and heavy hardware essential with prestrained dielectric actuators, as well as material problems associated with stress relaxation. The dependence of actuation behavior on gel morphology as evaluated from mechanical and microstructure studies is observed. In the case of IPMCs, ionic BCs employed in this study greatly facilitate processing compared to other contenders such as NafionRTM, which is commonly used in this class of EAPs. The unique copolymer investigated here (i) retains its mechanical integrity when highly solvated by polar solvents, (ii) demonstrates a high degree of actuation when tested in a cantilever configuration, and (iii) avoids the shortcomings of back-relaxation/overshoot within the testing conditions when used in combination with an appropriate solvent. In the second part of this work, two chemical strategies to design midblock sulfonated block ionomers are explored. In one case, selective sulfonation of the midblocks in triblock copolymers is achieved via a dioxane:sulfur trioxide chemistry, while in the other acetyl sulfate is used for the same purpose. Excellent control on the degree of sulfonation (DOS) is achieved. The block ionomers swell in different solvents while retaining their mechanical integrity. They show disorder-order, order-order, and order-reduced order morphological transitions as DOS varies. These transitions in morphologies are reflected in their thermal behavior as well. The microstructures show periodicity, which is, again, a function of DOS. The transitions are explained in terms of the molar volume expansion and volume densification of the blocks on sulfonation. The ionic levels, morphology and periodicity in microstructure are important for applications such as actuators, sensors and fuel cell membranes. The ability to tune these aspects in the ionomers designed in this work make them potential candidates for these applications.

The experimental design of the Missouri Ozark Forest Ecosystem Project

Treesearch

Steven L. Sheriff; Shuoqiong He

1997-01-01

The Missouri Ozark Forest Ecosystem Project (MOFEP) is an experiment that examines the effects of three forest management practices on the forest community. MOFEP is designed as a randomized complete block design using nine sites divided into three blocks. Treatments of uneven-aged, even-aged, and no-harvest management were randomly assigned to sites within each block...

7. BLOCK HOUSE BASEMENT LOOKING THROUGH DOOR INTO CABLE TUNNEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. BLOCK HOUSE BASEMENT LOOKING THROUGH DOOR INTO CABLE TUNNEL RUNNING BETWEEN BLOCK HOUSE AND STATIC TEST TOWER. - Marshall Space Flight Center, East Test Area, Block House, Huntsville, Madison County, AL

"Eyeball test" of thermographic patterns for predicting a successful lateral infraclavicular block.

PubMed

Andreasen, Asger M; Linnet, Karen E; Asghar, Semera; Rothe, Christian; Rosenstock, Charlotte V; Lange, Kai H W; Lundstrøm, Lars H

2017-11-01

Increased distal skin temperature can be used to predict the success of lateral infraclavicular (LIC) block. We hypothesized that an "eyeball test" of specific infrared thermographic patterns after LIC block could be used to determine block success. In this observational study, five observers trained in four distinct thermographic patterns independently evaluated thermographic images of the hands of 40 patients at baseline and at one-minute intervals for 30 min after a LIC block. Sensitivity, specificity, and predictive values of a positive and a negative test were estimated to evaluate the validity of specific thermographic patterns for predicting a successful block. Sensory and motor block of the musculocutaneous, radial, ulnar, and median nerves defined block success. Fleiss' kappa statistics of multiple interobserver agreements were used to evaluate reliability. As a diagnostic test, the defined specific thermographic patterns of the hand predicted a successful block with increasing accuracy over the 30-min observation period. Block success was predicted with a sensitivity of 92.4% (95% confidence interval [CI], 86.8 to 96.2) and with a specificity of 84.0% (95% CI, 70.3 to 92.4) at min 30. The Fleiss' kappa for the five observers was 0.87 (95% CI, 0.77 to 0.96). We conclude that visual evaluation by an eyeball test of specific thermographic patterns of the blocked hands may be useful as a valid and reliable diagnostic test for predicting a successful LIC block.

Testing the Immediate and Long-Term Efficacy of a Tier 2 Kindergarten Mathematics Intervention

ERIC Educational Resources Information Center

Clarke, Ben; Doabler, Christian T.; Smolkowski, Keith; Kurtz-Nelson, Evangeline; Fien, Hank; Baker, Scott K.; Kosty, Derek

2016-01-01

This study examined the efficacy of a kindergarten mathematics intervention program, ROOTS, focused on developing whole-number understanding in the areas of counting and cardinality and operations and algebraic thinking for students at risk in mathematics. The study utilized a randomized block design with students within classrooms randomly…

IRT Item Parameter Scaling for Developing New Item Pools

ERIC Educational Resources Information Center

Kang, Hyeon-Ah; Lu, Ying; Chang, Hua-Hua

2017-01-01

Increasing use of item pools in large-scale educational assessments calls for an appropriate scaling procedure to achieve a common metric among field-tested items. The present study examines scaling procedures for developing a new item pool under a spiraled block linking design. The three scaling procedures are considered: (a) concurrent…

Gestalt Perception and Local-Global Processing in High-Functioning Autism

ERIC Educational Resources Information Center

Bolte, Sven; Holtmann, Martin; Poustka, Fritz; Scheurich, Armin; Schmidt, Lutz

2007-01-01

This study examined gestalt perception in high-functioning autism (HFA) and its relation to tasks indicative of local visual processing. Data on of gestalt perception, visual illusions (VI), hierarchical letters (HL), Block Design (BD) and the Embedded Figures Test (EFT) were collected in adult males with HFA, schizophrenia, depression and…

Multiple Learning Strategies Project. Small Engine Repair Service. [Regular Vocational. Vol. 2.

ERIC Educational Resources Information Center

Pitts, Jim; And Others

This instructional package is one of two designed for use by regular vocational students in the vocational area of small engine repair service. Contained in this document are forty-nine learning modules organized into eleven units: test equipment; motorcycle; engine removal and replacement; machining; tune-ups; short blocks; storage; filling out…

Application of Composite Materials to Truck Components: Leaf Springs and Propeller Shafts for 5-Ton Trucks

DTIC Science & Technology

1981-11-01

Fiberglass-Epoxy Resin Matrix Composites 2(L ABSTRACT (Caautlrue am reverse de bf IHI wee•a’y d Identify by block number) The objective of the program was to...Army truck are designed using resin matrix composite materials. Both design studies and prototype fabrication and testing are included in the program...For the leaf springs (both front and rear) a hybrid design using steel DD FOR 143 ED#T1ON OF I NOV65 IS OBSOLETE SECURITY CLASSIFICATION OF THIS PAGE

Double-Blind Crossover Study to Compare Pain Experience During Inferior Alveolar Nerve Block Administration Using Buffered Two Percent Lidocaine in Children.

PubMed

Chopra, Radhika; Jindal, Garima; Sachdev, Vinod; Sandhu, Meera

2016-01-01

Buffering of anesthetic solutions has been suggested to reduce pain on injection and onset of anesthesia. The purpose of this study was to assess the reduction in pain on injection during inferior alveolar nerve block administration in children. A double blind crossover study was designed where 30 six- to 12-year-old patients received two sessions of inferior alveolar nerve block scheduled one week apart. Two percent lidocaine with 1:200,000 epinephrine was given during one appointment, and a buffered solution was given during the other. Pain on injection was assessed using the sound, eye, and motor (SEM) scale, and the time to onset was assessed after gingival probing. The Heft-Parker visual analogue scale (HP-VAS) was self recorded by the patient after administration of local anesthesia. When tested using Mann-Whitney analysis, no significant differences were found between the SEM scores (P=0.71) and HP-VAS scores (P=0.93) for the two solutions used. Student's t test was used to assess the difference in the onset of anesthesia, which was also found to be statistically insignificant (P=0.824). Buffered lidocaine did not reduce the pain on injection or time to onset of anesthesia for inferior alveolar nerve block in children.

Test of a non-physical barrier consisting of light, sound, and bubble screen to block upstream movement of sea lamprey in an experimental raceway

USGS Publications Warehouse

Miehls, Scott M.; Johnson, Nicholas S.; Hrodey, Pete J.

2017-01-01

Control of the invasive Sea Lamprey Petromyzon marinus is critical for management of commercial and recreational fisheries in the Laurentian Great Lakes. Use of physical barriers to block Sea Lampreys from spawning habitat is a major component of the control program. However, the resulting interruption of natural streamflow and blockage of nontarget species present substantial challenges. Development of an effective nonphysical barrier would aid the control of Sea Lampreys by eliminating their access to spawning locations while maintaining natural streamflow. We tested the effect of a nonphysical barrier consisting of strobe lights, low-frequency sound, and a bubble screen on the movement of Sea Lampreys in an experimental raceway designed as a two-choice maze with a single main channel fed by two identical inflow channels (one control and one blocked). Sea Lampreys were more likely to move upstream during trials when the strobe light and low-frequency sound were active compared with control trials and trials using the bubble screen alone. For those Sea Lampreys that did move upstream to the confluence of inflow channels, no combination of stimuli or any individual stimulus significantly influenced the likelihood that Sea Lampreys would enter the blocked inflow channel, enter the control channel, or return downstream.

Apollo Telescope Mount (ATM) gimballed star tracker. [developed for the Skylab program

NASA Technical Reports Server (NTRS)

Lana, J. D.

1974-01-01

Design and development of six gimballed star trackers for Skylab's Apollo Telescope Mount, which performed successfully on all three manned Skylab missions and accumulated a total usage time of approximately 3,500 hours, is described in terms of configurations, materials and construction, qualification testing, performance, and reliability characteristics. A brief program history and design changes incorporated during the life of the program are also discussed. Extensive drawings, block diagrams, and photographs are provided.

Finalizing the DTAG: Implementation and Testing of Design Improvements for Reliability and Availability

DTIC Science & Technology

2015-09-30

acoustics and fine scale motion. The success of the Dtag has resulted in an increased demand for the instrument from researchers both within the...sensor blocks sound when the animal is close to the surface. The polyethylene shell was eliminated in the Dtag-3 design to improve acoustic ...into 3 main sub-assemblies (Figure 5): 1) foam sub-assembly, 2) sensor sub-assembly, and 3) Electronics sub-assembly. This separation enables rapid

Effect of Thermal and Chemical Treatment on the Microstructural, Mechanical and Machining Performance of W319 Al-Si-Cu Cast Alloy Engine Blocks and Directionally Solidified Machinability Test Blocks

NASA Astrophysics Data System (ADS)

Szablewski, Daniel

The research presented in this work is focused on making a link between casting microstructural, mechanical and machining properties for 319 Al-Si sand cast components. In order to achieve this, a unique Machinability Test Block (MTB) is designed to simulate the Nemak V6 Al-Si engine block solidification behavior. This MTB is then utilized to cast structures with in-situ nano-alumina particle master alloy additions that are Mg based, as well as independent in-situ Mg additions, and Sr additions to the MTB. The Universal Metallurgical Simulator and Analyzer (UMSA) Technology Platform is utilized for characterization of each cast structure at different Secondary Dendrite Arm Spacing (SDAS) levels. The rapid quench method and Jominy testing is used to assess the capability of the nano-alumina master alloy to modify the microstructure at different SDAS levels. Mechanical property assessment of the MTB is done at different SDAS levels on cast structures with master alloy additions described above. Weibull and Quality Index statistical analysis tools are then utilized to assess the mechanical properties. The MTB is also used to study single pass high speed face milling and bi-metallic cutting operations where the Al-Si hypoeutectic structure is combined with hypereutectoid Al-Si liners and cast iron cylinder liners. These studies are utilized to aid the implementation of Al-Si liners into the Nemak V6 engine block and bi-metallic cutting of the head decks. Machining behavior is also quantified for the investigated microstructures, and the Silicon Modification Level (SiML) is utilized for microstructural analysis as it relates to the machining behavior.

Pre-test CFD Calculations for a Bypass Flow Standard Problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rich Johnson

The bypass flow in a prismatic high temperature gas-cooled reactor (HTGR) is the flow that occurs between adjacent graphite blocks. Gaps exist between blocks due to variances in their manufacture and installation and because of the expansion and shrinkage of the blocks from heating and irradiation. Although the temperature of fuel compacts and graphite is sensitive to the presence of bypass flow, there is great uncertainty in the level and effects of the bypass flow. The Next Generation Nuclear Plant (NGNP) program at the Idaho National Laboratory has undertaken to produce experimental data of isothermal bypass flow between three adjacentmore » graphite blocks. These data are intended to provide validation for computational fluid dynamic (CFD) analyses of the bypass flow. Such validation data sets are called Standard Problems in the nuclear safety analysis field. Details of the experimental apparatus as well as several pre-test calculations of the bypass flow are provided. Pre-test calculations are useful in examining the nature of the flow and to see if there are any problems associated with the flow and its measurement. The apparatus is designed to be able to provide three different gap widths in the vertical direction (the direction of the normal coolant flow) and two gap widths in the horizontal direction. It is expected that the vertical bypass flow will range from laminar to transitional to turbulent flow for the different gap widths that will be available.« less

Bayesian block-diagonal variable selection and model averaging

PubMed Central

Papaspiliopoulos, O.; Rossell, D.

2018-01-01

Summary We propose a scalable algorithmic framework for exact Bayesian variable selection and model averaging in linear models under the assumption that the Gram matrix is block-diagonal, and as a heuristic for exploring the model space for general designs. In block-diagonal designs our approach returns the most probable model of any given size without resorting to numerical integration. The algorithm also provides a novel and efficient solution to the frequentist best subset selection problem for block-diagonal designs. Posterior probabilities for any number of models are obtained by evaluating a single one-dimensional integral, and other quantities of interest such as variable inclusion probabilities and model-averaged regression estimates are obtained by an adaptive, deterministic one-dimensional numerical integration. The overall computational cost scales linearly with the number of blocks, which can be processed in parallel, and exponentially with the block size, rendering it most adequate in situations where predictors are organized in many moderately-sized blocks. For general designs, we approximate the Gram matrix by a block-diagonal matrix using spectral clustering and propose an iterative algorithm that capitalizes on the block-diagonal algorithms to explore efficiently the model space. All methods proposed in this paper are implemented in the R library mombf. PMID:29861501

Effects of different practice conditions on acquisition, retention, and transfer of soccer skills by 9-year-old schoolchildren.

PubMed

Vera, Juan Granda; Alvarez, José Carlos Barbero; Medina, Mariano Montilla

2008-04-01

This study was designed to examine effects of three practice models, blocked, variable, and combined, on the acquisition, retention, and transfer of new motor skills. 67 subjects (M age = 9.5 yr., SD = .3) from the fourth year of primary school (31 boys and 26 girls) were assigned at random to three different practice groups (Blocked = 22, Variable = 23, Combined = 22) to study acquisition of two skills, dribbling a soccer ball and kicking a soccer ball at a stationary target using the dominant foot. All participants received a pretest and posttest, a transfer test, and a retention test 2 wk. later. Analysis showed significant improvement after practice of kicking skills by the three groups but not in the dribbling skills, for which only the combined practice group showed any notable improvement. At the end of acquisition, the combined practice group had significantly better performance on the dribbling task than the other two groups. However, the only differences noted in performance of kicking the ball with the dominant foot were by combined practice and blocked groups.

General Purpose Heat Source Simulator

NASA Technical Reports Server (NTRS)

Emrich, William J., Jr.

2008-01-01

The General Purpose Heat Source (GPHS) project seeks to combine the development of an electrically heated, single GPHS module simulator with the evaluation of potential nuclear surface power systems. The simulator is designed to match the form, fit, and function of actual GPHS modules which normally generate heat through the radioactive decay of Pu238. The use of electrically heated modules rather than modules containing Pu238 facilitates the testing of the subsystems and systems without sacrificing the quantity and quality of the test data gathered. Current GPHS activities are centered on developing robust heater designs with sizes and weights which closely match those of actual Pu238 fueled GPHS blocks. Designs are being pursued which will allow operation up to 1100 C.

Effect of Nanoparticle Core Size on Polymer-Coated Gold Nanoparticle Location in Block Copolymers

NASA Astrophysics Data System (ADS)

Petrie, J. D.; Fredrickson, G. H.; Kramer, E. J.

2009-03-01

Gold nanoparticles modified by short chain polymer thiols [Au-PS] can be designed to strongly localize either in the PS domains of a polystyrene-b-poly(2-vinylpyridine) [PS-PVP] block copolymer or at the interface. The P2VP block has a stronger attractive interaction with bare gold than the PS block. Thus, when the areal chain density σ of end-attached PS chains falls below a critical areal chain density σc the Au-PS nanoparticles adsorb to the PS-b-P2VP interface. The effect of the polymer ligand molecular weight on the σc has been shown to scale as σc˜ ((R + Rg)/(R*Rg))̂2, where R is the curvature of the Au nanoparticle core radius. To test this scaling relation for σc further we are synthesizing gold nanoparticles with different core radii and will present preliminary results on σc as a function of R.

Effect of Ligand Molecular Weight and Nanoparticle Core Size on Polymer-Coated Gold Nanoparticle Location in Block Copolymers

NASA Astrophysics Data System (ADS)

Petrie, Joshua; Kim, Bumjoon; Fredrickson, Glenn; Kramer, Ed

2008-03-01

Gold nanoparticles modified by short chain polymer thiols [Au-PS] can be designed to strongly localize in either domain of a polystyrene-b-poly(2-vinylpyridine) [PS-PVP] block copolymer or at the interface. The P2VP block has a stronger attractive interaction with bare gold than the PS block. Thus, when the areal chain density σ of end-attached PS chains falls below a critical areal chain density σc the Au-PS nanoparticles adsorb to the PS-b-P2VP interface. The effect of the polymer ligand molecular weight on the σchas been shown to scale as σc˜ ((R+Rg)/(R*Rg))̂2, where R is the curvature of the Au nanoparticle core radius. To test this scaling relation for σc further we are synthesizing gold nanoparticles with different core radii and will present preliminary results on σcas a function of R.

New database for improving virtual system “body-dress”

NASA Astrophysics Data System (ADS)

Yan, J. Q.; Zhang, S. C.; Kuzmichev, V. E.; Adolphe, D. C.

2017-10-01

The aim of this exploration is to develop a new database of solid algorithms and relations between the dress fit and the fabric mechanical properties, the pattern block construction for improving the reality of virtual system “body-dress”. In virtual simulation, the system “body-clothing” sometimes shown distinct results with reality, especially when important changes in pattern block and fabrics were involved. In this research, to enhance the simulation process, diverse fit parameters were proposed: bottom height of dress, angle of front center contours, air volume and its distribution between dress and dummy. Measurements were done and optimized by ruler, camera, 3D body scanner image processing software and 3D modeling software. In the meantime, pattern block indexes were measured and fabric properties were tested by KES. Finally, the correlation and linear regression equations between indexes of fabric properties, pattern blocks and fit parameters were investigated. In this manner, new database could be extended in programming modules of virtual design for more realistic results.

Parallelized implicit propagators for the finite-difference Schrödinger equation

NASA Astrophysics Data System (ADS)

Parker, Jonathan; Taylor, K. T.

1995-08-01

We describe the application of block Gauss-Seidel and block Jacobi iterative methods to the design of implicit propagators for finite-difference models of the time-dependent Schrödinger equation. The block-wise iterative methods discussed here are mixed direct-iterative methods for solving simultaneous equations, in the sense that direct methods (e.g. LU decomposition) are used to invert certain block sub-matrices, and iterative methods are used to complete the solution. We describe parallel variants of the basic algorithm that are well suited to the medium- to coarse-grained parallelism of work-station clusters, and MIMD supercomputers, and we show that under a wide range of conditions, fine-grained parallelism of the computation can be achieved. Numerical tests are conducted on a typical one-electron atom Hamiltonian. The methods converge robustly to machine precision (15 significant figures), in some cases in as few as 6 or 7 iterations. The rate of convergence is nearly independent of the finite-difference grid-point separations.

Design and optimization of surface profilometer based on coplanar guide rail

NASA Astrophysics Data System (ADS)

Chen, Shuai; Dai, Yifan; Hu, Hao; Tie, Guipeng

2017-10-01

In order to implement the sub-micron precision measurement, a surface profilometer which based on the coplanar guide rail is designed. This profilometer adopts the open type air floating load and is driven by the magnetic force. As to achieve sub-micron accuracy, the flatness of granite guide working face and aerodynamic block are both processed to the micron level based on the homogenization of air flotation film theory. Permanent magnet which could reduce the influence of the driving disturbance to the measurement accuracy is used as the driving part. In this paper, the bearing capacity and the air floating stiffness of air floating block are both simulated and analyzed as to optimize the design parameters firstly. The layout and magnetic force of the magnet are also simulated. According to the simulation results, type selection and the position arrangement of the magnets are then confirmed. The test results on the experimental platform show that the surface profilometer based on coplanar guide rail possess the basis for realizing the submicron precision measurement.

NASA's Space Launch System Marks Critical Design Review

NASA Technical Reports Server (NTRS)

Singer, Chris

2016-01-01

With completion of its Critical Design Review (CDR) in 2015, NASA is deep into the manufacturing and testing phases of its new Space Launch System (SLS) for beyond-Earth exploration. This CDR was the first in almost 40 years for a NASA human launch vehicle and marked another successful milestone on the road to the launch of a new era of deep space exploration. The review marked the 90-percent design-complete, a final look at the design and development plan of the integrated vehicle before full-scale fabrications begins and the prelude to the next milestone, design certification. Specifically, the review looked at the first of three increasingly capable configurations planned for SLS. This "Block I" design will stand 98.2 meters (m) (322 feet) tall and provide 39.1 million Newtons (8.8 million pounds) of thrust at liftoff to lift a payload of approximately 70 metric tons (154,000 pounds). This payload is more than double that of the retired space shuttle program or other current launch vehicles. It dramatically increases the mass and volume of human and robotic exploration. Additionally, it will decrease overall mission risk, increase safety, and simplify ground and mission operations - all significant considerations for crewed missions and unique, high-value national payloads. The Block 1 SLS will launch NASA's Orion Multi-Purpose Crew Vehicle (MPCV) on an uncrewed flight beyond the moon and back and the first crewed flight around the moon. The current design has a direct evolutionary path to a vehicle with a 130t lift capability that offers even more flexibility to reduce planetary trip times, simplify payload design cycles, and provide new capabilities such as planetary sample returns. Every major element of SLS has hardware in production or testing, including flight hardware for the Exploration 1 (EM-1) test flight. In fact, the SLS MPCV-to-Stage-Adapter (MSA) flew successfully on the Exploration Flight Test (EFT) 1 launch of a Delta IV and Orion spacecraft in December 2014. This paper will discuss these and other technical and programmatic successes and challenges over the past year and provide a preview of work ahead before the first flight of this new capability.

Expediting analog design retargeting by design knowledge re-use and circuit synthesis: a practical example on a Delta-Sigma modulator

NASA Astrophysics Data System (ADS)

Webb, Matthew; Tang, Hua

2016-08-01

In the past decade or two, due to constant and rapid technology changes, analog design re-use or design retargeting to newer technologies has been brought to the table in order to expedite the design process and improve time-to-market. If properly conducted, analog design retargeting could significantly cut down design cycle compared to designs starting from the scratch. In this article, we present an empirical and general method for efficient analog design retargeting by design knowledge re-use and circuit synthesis (CS). The method first identifies circuit blocks that compose the source system and extracts the performance parameter specifications of each circuit block. Then, for each circuit block, it scales the values of design variables (DV) from the source design to derive an initial design in the target technology. Depending on the performance of this initial target design, a design space is defined for synthesis. Subsequently, each circuit block is automatically synthesised using state-of-art analog synthesis tools based on a combination of global and local optimisation techniques to achieve comparable performance specifications to those extracted from the source system. Finally, the overall system is composed of those synthesised circuit blocks in the target technology. We illustrate the method using a practical example of a complex Delta-Sigma modulator (DSM) circuit.

Analgesic efficacy of ultrasound guided transversus abdominis plane block versus local anesthetic infiltration in adult patients undergoing single incision laparoscopic cholecystectomy: A randomized controlled trial

PubMed Central

Bava, Ejas P.; Ramachandran, Rashmi; Rewari, Vimi; Chandralekha; Bansal, Virinder Kumar; Trikha, Anjan

2016-01-01

Background: Transversus abdominis plane (TAP) block has been used to provide intra- and post-operative analgesia with single incision laparoscopic (SIL) bariatric and gynecological surgery with mixed results. Its efficacy in providing analgesia for SIL cholecystectomy (SILC) via the same approach remains unexplored. Aims: The primary objective of our study was to compare the efficacy of bilateral TAP block with local anesthetic infiltration for perioperative analgesia in patients undergoing SILC. Settings and Design: This was a prospective, randomized, controlled, double-blinded trial performed in a tertiary care hospital. Materials and Methods: Forty-two patients undergoing SILC were randomized to receive either ultrasound-guided (USG) bilateral mid-axillary TAP blocks with 0.375% ropivacaine or local anesthetic infiltration of the port site. The primary outcome measure was the requirement of morphine in the first 24 h postoperatively. Statistical Analysis: The data were analyzed using t-test, Mann–Whitney test or Chi-square test. Results: The 24 h morphine requirement (mean ± standard deviation) was 34.57 ± 14.64 mg in TAP group and 32.76 ± 14.34 mg in local infiltration group (P = 0.688). The number of patients requiring intraoperative supplemental fentanyl in TAP group was 8 and in local infiltration group was 16 (P = 0.028). The visual analog scale scores at rest and on coughing were significantly higher in the local infiltration group in the immediate postoperative period (P = 0.034 and P = 0.007, respectively). Conclusion: USG bilateral TAP blocks were not effective in decreasing 24 h morphine requirement as compared to local anesthetic infiltration in patients undergoing SILC although it provided some analgesic benefit intraoperatively and in the initial 4 h postoperatively. Hence, the benefits of TAP blocks are not worth the effort and time spent for administering them for this surgery. PMID:27746552

Cognitive factors in the close visual and magnetic particle inspection of welds underwater.

PubMed

Leach, J; Morris, P E

1998-06-01

Underwater close visual inspection (CVI) and magnetic particle inspection (MPI) are major components of the commercial diver's job of nondestructive testing and the maintenance of subsea structures. We explored the accuracy of CVI in Experiment 1 and that of MPI in Experiment 2 and observed high error rates (47% and 24%, respectively). Performance was strongly correlated with embedded figures and visual search tests and was unrelated to length of professional diving experience, formal inspection qualification, or age. Cognitive tests of memory for designs, spatial relations, dotted outlines, and block design failed to correlate with performance. Actual or potential applications of this research include more reliable inspection reporting, increased effectiveness from current inspection techniques, and directions for the refinement of subsea inspection equipment.

Design and implemention of a multi-functional x-ray computed tomography system

NASA Astrophysics Data System (ADS)

Li, Lei; Xi, Xiaoqi; Han, Yu; Yan, Bin; Zhang, Xiang; Deng, Lin; Chen, Siyu; Jin, Zhao; Li, Zengguang

2015-10-01

A powerful volume X-ray tomography system has been designed and constructed to provide an universal tool for the three-dimensional nondestructive testing and investigation of industrial components, automotive, electronics, aerospace components, new materials, etc. The combined system is equipped with two commercial X-ray sources, sharing one flat panel detector of 400mm×400mm. The standard focus 450kV high-energy x-ray source is optimized for complex and high density components such as castings, engine blocks and turbine blades. And the microfocus 225kV x-ray source is to meet the demands of micro-resolution characterization applications. Thus the system's penetration capability allows to scan large objects up to 200mm thick dense materials, and the resolution capability can meet the demands of 20μm microstructure inspection. A high precision 6-axis manipulator system is fitted, capable of offset scanning mode in large field of view requirements. All the components are housed in a room with barium sulphate cement. On the other hand, the presented system expands the scope of applications such as dual energy research and testing. In this paper, the design and implemention of the flexible system is described, as well as the preliminary tomographic imaging results of an automobile engine block.

Channel Estimation and Pilot Design for Massive MIMO Systems with Block-Structured Compressive Sensing

NASA Astrophysics Data System (ADS)

Lv, ZhuoKai; Yang, Tiejun; Zhu, Chunhua

2018-03-01

Through utilizing the technology of compressive sensing (CS), the channel estimation methods can achieve the purpose of reducing pilots and improving spectrum efficiency. The channel estimation and pilot design scheme are explored during the correspondence under the help of block-structured CS in massive MIMO systems. The block coherence property of the aggregate system matrix can be minimized so that the pilot design scheme based on stochastic search is proposed. Moreover, the block sparsity adaptive matching pursuit (BSAMP) algorithm under the common sparsity model is proposed so that the channel estimation can be caught precisely. Simulation results are to be proved the proposed design algorithm with superimposed pilots design and the BSAMP algorithm can provide better channel estimation than existing methods.

Testing of a single graded groove variable conductance heat pipe

NASA Astrophysics Data System (ADS)

Kapolnek, Michael R.; Holmes, H. R.; Hager, Brian

1992-07-01

Variable conductance heat pipes (VCHPs) with transport capacities in the 50,000 to 100,000 Watt-inch range will be required to transport the large heat loads anticipated for advanced spacecraft. A high-reliability, nonarterial constant conductance heat pipe with this capacity, the Single Graded Groove (SGG) heat pipe, was developed for NASA's Space Station Freedom. The design and testing of a variable conductance SGG heat pipe are described. Response of the pipe to startup and heat load changes was excellent. After correcting for condenser temperature changes, the evaporator temperature varied by only +/- 4 F for large evaporator heat load changes. The surface tension difference between ends of the gas blocked region was found to measurably affect the performance of the pipe. Performance was negligibly affected by Marangoni flow in the gas blocked region.

Reliability study of Piezoelectric Structures Dedicated to Energy Harvesting by the Way of Blocking Force Investigation

NASA Astrophysics Data System (ADS)

Maaroufi, S.; Parrain, F.; Lefeuvre, E.; Boutaud, B.; Dal Molin, R.

2015-12-01

In this paper we propose an approach to study the reliability of piezoelectric structures and more precisely energy harvesting micro-devices dedicated to autonomous active medical implants (new generation pacemakers). The structure under test is designed as a bimorph piezoelectric cantilever with a seismic mass at its tip. Good understanding of material aging and mechanical failure is critical for this kind of system. To study the reliability and durability of the piezoelectric part we propose to establish a new accelerated methodology and an associated test bench where the environment and stimuli can be precisely controlled over a wide period of time. This will allow the identification of potential failure modes and the study of their impacts by the way of direct mechanical investigation based on stiffness and blocking force measurements performed periodically.

Optimizing Experimental Designs: Finding Hidden Treasure.

USDA-ARS?s Scientific Manuscript database

Classical experimental design theory, the predominant treatment in most textbooks, promotes the use of blocking designs for control of spatial variability in field studies and other situations in which there is significant variation among heterogeneity among experimental units. Many blocking design...

Effects of transmission-blocking vaccines simultaneously targeting pre- and post-fertilization antigens in the rodent malaria parasite Plasmodium yoelii.

PubMed

Zheng, Li; Pang, Wei; Qi, Zanmei; Luo, Enjie; Cui, Liwang; Cao, Yaming

2016-08-08

Transmission-blocking vaccine (TBV) is a promising strategy for interrupting the malaria transmission cycle. Current TBV candidates include both pre- and post-fertilization antigens expressed during sexual development of the malaria parasites. We tested whether a TBV design combining two sexual-stage antigens has better transmission-blocking activity. Using the rodent malaria model Plasmodium yoelii, we pursued a DNA vaccination strategy with genes encoding the gametocyte antigen Pys48/45 and the major ookinete surface protein Pys25. Immunization of mice with DNA constructs expression either Pys48/45 or Pys25 elicited strong antibody responses, which specifically recognized a ~45 and ~25 kDa protein from gametocyte and ookinete lysates, respectively. Immune sera from mice immunized with DNA constructs expressing Pys48/45 and Pys25 individually and in combination displayed evident transmission-blocking activity in in vitro ookinete culture and direct mosquito feeding experiments. With both assays, the Pys25 sera had higher transmission-blocking activity than the Pys48/45 sera. Intriguingly, compared with the immunization with the individual DNA vaccines, immunization with both DNA constructs produced lower antibody responses against individual antigens. The resultant immune sera from the composite vaccination had significantly lower transmission-blocking activity than those from Pys25 DNA immunization group, albeit the activity was substantially higher than that from the Pys48 DNA vaccination group. This result suggested that vaccination with the two DNA constructs did not achieve a synergistic effect, but rather caused interference in inducing antigen-specific antibody responses. This result has important implications for future design of composite vaccines targeting different sexual antigens.

Design and implementation of a proficiency-based, structured endoscopy course for medical students applying for a surgical specialty

PubMed Central

De Win, Gunter; Van Bruwaene, Siska; Allen, Christopher; De Ridder, Dirk

2013-01-01

Background Surgical simulation is becoming increasingly important in surgical education. Despite the important work done on simulators, simulator model development, and simulator assessment methodologies, there is a need for development of integrated simulators in the curriculum. In this paper, we describe the design of our evidence-based preclinical training program for medical students applying for a surgical career at the Centre for Surgical Technologies. Methods Twenty-two students participated in this training program. During their final months as medical students, they received structured, proficiency-based endoscopy training. The total amount of mentored training was 18 hours and the training was organized into three training blocks. The first block focused on psychomotor training, the second block focused on laparoscopic stitching and suturing, and the third block on laparoscopic dissection techniques and hemostasis. Deliberate practice was allowed and students had to show proficiency before proceeding to the next training block. Students’ psychomotor abilities were tested before the course and after each training block. At the beginning of their careers as surgical registrars, their performance on a laparoscopic suturing task was compared with that of registrars from the previous year who did not have this training course. Student opinions about this course were evaluated using a visual analog scale. Results All students rated the training course as useful and their psychomotor abilities improved markedly. All students performed deliberate practice, and those who participated in this course scored significantly (P < 0.0001) better on the laparoscopic suturing task than first year registrars who did not participate in this course. Conclusion Organization of a structured preclinical training program in laparoscopy for final year medical students is feasible, attractive, and successful. PMID:23901308

3. "TEST STAND NO. 13, EXCAVATION PLAN & SECTIONS." Specifications ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. "TEST STAND NO. 1-3, EXCAVATION PLAN & SECTIONS." Specifications No. ENG 04-353-50-10; Drawing No. 60-0906; no sheet number within title block; D.O. SERIES 1109/10. Stamped: AS BUILT. No revisions or revision dates. Last work date on this drawing "Checked by EAG, 1/31/49." Though this drawing is specific to Test Stand 1-3, it also illustrates the general methods used for excavation design and retaining wall construction at Test Stand 1-5. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Test Stand 1-3, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Binaural noise reduction via cue-preserving MMSE filter and adaptive-blocking-based noise PSD estimation

NASA Astrophysics Data System (ADS)

Azarpour, Masoumeh; Enzner, Gerald

2017-12-01

Binaural noise reduction, with applications for instance in hearing aids, has been a very significant challenge. This task relates to the optimal utilization of the available microphone signals for the estimation of the ambient noise characteristics and for the optimal filtering algorithm to separate the desired speech from the noise. The additional requirements of low computational complexity and low latency further complicate the design. A particular challenge results from the desired reconstruction of binaural speech input with spatial cue preservation. The latter essentially diminishes the utility of multiple-input/single-output filter-and-sum techniques such as beamforming. In this paper, we propose a comprehensive and effective signal processing configuration with which most of the aforementioned criteria can be met suitably. This relates especially to the requirement of efficient online adaptive processing for noise estimation and optimal filtering while preserving the binaural cues. Regarding noise estimation, we consider three different architectures: interaural (ITF), cross-relation (CR), and principal-component (PCA) target blocking. An objective comparison with two other noise PSD estimation algorithms demonstrates the superiority of the blocking-based noise estimators, especially the CR-based and ITF-based blocking architectures. Moreover, we present a new noise reduction filter based on minimum mean-square error (MMSE), which belongs to the class of common gain filters, hence being rigorous in terms of spatial cue preservation but also efficient and competitive for the acoustic noise reduction task. A formal real-time subjective listening test procedure is also developed in this paper. The proposed listening test enables a real-time assessment of the proposed computationally efficient noise reduction algorithms in a realistic acoustic environment, e.g., considering time-varying room impulse responses and the Lombard effect. The listening test outcome reveals that the signals processed by the blocking-based algorithms are significantly preferred over the noisy signal in terms of instantaneous noise attenuation. Furthermore, the listening test data analysis confirms the conclusions drawn based on the objective evaluation.

Digital Morphing Wing: Active Wing Shaping Concept Using Composite Lattice-Based Cellular Structures.

PubMed

Jenett, Benjamin; Calisch, Sam; Cellucci, Daniel; Cramer, Nick; Gershenfeld, Neil; Swei, Sean; Cheung, Kenneth C

2017-03-01

We describe an approach for the discrete and reversible assembly of tunable and actively deformable structures using modular building block parts for robotic applications. The primary technical challenge addressed by this work is the use of this method to design and fabricate low density, highly compliant robotic structures with spatially tuned stiffness. This approach offers a number of potential advantages over more conventional methods for constructing compliant robots. The discrete assembly reduces manufacturing complexity, as relatively simple parts can be batch-produced and joined to make complex structures. Global mechanical properties can be tuned based on sub-part ordering and geometry, because local stiffness and density can be independently set to a wide range of values and varied spatially. The structure's intrinsic modularity can significantly simplify analysis and simulation. Simple analytical models for the behavior of each building block type can be calibrated with empirical testing and synthesized into a highly accurate and computationally efficient model of the full compliant system. As a case study, we describe a modular and reversibly assembled wing that performs continuous span-wise twist deformation. It exhibits high performance aerodynamic characteristics, is lightweight and simple to fabricate and repair. The wing is constructed from discrete lattice elements, wherein the geometric and mechanical attributes of the building blocks determine the global mechanical properties of the wing. We describe the mechanical design and structural performance of the digital morphing wing, including their relationship to wind tunnel tests that suggest the ability to increase roll efficiency compared to a conventional rigid aileron system. We focus here on describing the approach to design, modeling, and construction as a generalizable approach for robotics that require very lightweight, tunable, and actively deformable structures.

Digital Morphing Wing: Active Wing Shaping Concept Using Composite Lattice-Based Cellular Structures

PubMed Central

Jenett, Benjamin; Calisch, Sam; Cellucci, Daniel; Cramer, Nick; Gershenfeld, Neil; Swei, Sean

2017-01-01

Abstract We describe an approach for the discrete and reversible assembly of tunable and actively deformable structures using modular building block parts for robotic applications. The primary technical challenge addressed by this work is the use of this method to design and fabricate low density, highly compliant robotic structures with spatially tuned stiffness. This approach offers a number of potential advantages over more conventional methods for constructing compliant robots. The discrete assembly reduces manufacturing complexity, as relatively simple parts can be batch-produced and joined to make complex structures. Global mechanical properties can be tuned based on sub-part ordering and geometry, because local stiffness and density can be independently set to a wide range of values and varied spatially. The structure's intrinsic modularity can significantly simplify analysis and simulation. Simple analytical models for the behavior of each building block type can be calibrated with empirical testing and synthesized into a highly accurate and computationally efficient model of the full compliant system. As a case study, we describe a modular and reversibly assembled wing that performs continuous span-wise twist deformation. It exhibits high performance aerodynamic characteristics, is lightweight and simple to fabricate and repair. The wing is constructed from discrete lattice elements, wherein the geometric and mechanical attributes of the building blocks determine the global mechanical properties of the wing. We describe the mechanical design and structural performance of the digital morphing wing, including their relationship to wind tunnel tests that suggest the ability to increase roll efficiency compared to a conventional rigid aileron system. We focus here on describing the approach to design, modeling, and construction as a generalizable approach for robotics that require very lightweight, tunable, and actively deformable structures. PMID:28289574

NASA's Space Launch System: Development and Progress

NASA Technical Reports Server (NTRS)

Honeycutt, John; Lyles, Garry

2016-01-01

NASA is embarked on a new era of space exploration that will lead to new capabilities, new destinations, and new discoveries by both human and robotic explorers. Today, the International Space Station (ISS), supported by NASA's commercial partners, and robotic probes, are yielding knowledge that will help make this exploration possible. NASA is developing both the Orion crew vehicle and the Space Launch System (SLS) that will carry out a series of increasingly challenging missions that will eventually lead to human exploration of Mars. This paper will discuss the development and progress on the SLS. The SLS architecture was designed to be safe, affordable, and sustainable. The current configuration is the result of literally thousands of trade studies involving cost, performance, mission requirements, and other metrics. The initial configuration of SLS, designated Block 1, will launch a minimum of 70 metric tons (t) into low Earth orbit - significantly greater capability than any current launch vehicle. It is designed to evolve to a capability of 130 t through the use of upgraded main engines, advanced boosters, and a new upper stage. With more payload mass and volume capability than any rocket in history, SLS offers mission planners larger payloads, faster trip times, simpler design, shorter design cycles, and greater opportunity for mission success. Since the program was officially created in fall 2011, it has made significant progress toward first launch readiness of the Block 1 vehicle in 2018. Every major element of SLS continued to make significant progress in 2015. The Boosters element fired Qualification Motor 1 (QM-1) in March 2015, to test the 5-segment motor, including new insulation, joint, and propellant grain designs. The Stages element marked the completion of more than 70 major components of test article and flight core stage tanks. The Liquid Engines element conducted seven test firings of an RS-25 engine under SLS conditions. The Spacecraft/Payload Integration and Evolution element marked completion of the upper stage test article. Major work continues in 2016 as the program continues both flight and development RS-25 engine testing, begins welding test article and flight core stage tanks, completes stage adapter manufacturing, and test fires the second booster qualification motor. This paper will discuss the program's key accomplishments to date and the challenging work ahead for what will be the world's most capable launch vehicle.

Evaluation of non-selective refocusing pulses for 7 T MRI

PubMed Central

Moore, Jay; Jankiewicz, Marcin; Anderson, Adam W.; Gore, John C.

2011-01-01

There is a continuing need for improved RF pulses that achieve proper refocusing in the context of ultra-high field (≥ 7 T) human MRI. Simple block or sinc pulses are highly susceptible to RF field inhomogeneities, and adiabatic pulses are generally considered too SAR intensive for practical use at 7 T. The performance of the array of pulses falling between these extremes, however, has not been systematically evaluated. The aim of this work was to compare the performances of 21 non-selective refocusing pulses spanning a range of durations and SAR levels. The evaluation was based upon simulations and both phantom and in vivo human brain experiments conducted at 7 T. Tested refocusing designs included block, composite block, BIR-4, hyperbolic secant, and numerically optimized composite waveforms. These pulses were divided into three SAR classes and two duration categories, and, based on signal gain in a 3-D spin echo sequence, practical recommendations on usage are made within each category. All evaluated pulses were found to produce greater volume-averaged signals relative to a 180° block pulse. Although signal gains often come with the price of increased SAR or duration, some pulses were found to result in significant signal enhancement while also adhering to practical constraints. This work demonstrates the signal gains and losses realizable with single-channel refocusing pulse designs and should assist in the selection of suitable refocusing pulses for practical 3-D spin-echo imaging at 7 T. It further establishes a reference against which future pulses and multi-channel designs can be compared. PMID:22177384

High Performance Compression of Science Data

NASA Technical Reports Server (NTRS)

Storer, James A.; Carpentieri, Bruno; Cohn, Martin

1994-01-01

Two papers make up the body of this report. One presents a single-pass adaptive vector quantization algorithm that learns a codebook of variable size and shape entries; the authors present experiments on a set of test images showing that with no training or prior knowledge of the data, for a given fidelity, the compression achieved typically equals or exceeds that of the JPEG standard. The second paper addresses motion compensation, one of the most effective techniques used in interframe data compression. A parallel block-matching algorithm for estimating interframe displacement of blocks with minimum error is presented. The algorithm is designed for a simple parallel architecture to process video in real time.

Investigation of Kevlar fabric-based materials for use with inflatable structures

NASA Technical Reports Server (NTRS)

Niccum, R. J.; Munson, J. B.; Rueter, L. L.

1977-01-01

Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported. The practicality of using Kevlar in aerostat materials is demonstrated, and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar-based materials are compared with conventional Dacron-reinforced counterparts. A comprehensive test and qualification program is discussed, and considerable quantitative biaxial tensile and shear test data are provided.

Mitigating Upsets in SRAM-Based FPGAs from the Xilinx Virtex 2 Family

NASA Technical Reports Server (NTRS)

Swift, G. M.; Yui, C. C.; Carmichael, C.; Koga, R.; George, J. S.

2003-01-01

Static random access memory (SRAM) upset rates in field programmable gate arrays (FPGAs) from the Xilinx Virtex 2 family have been tested for radiation effects on configuration memory, block RAM and the power-on-reset (POR) and SelectMAP single event functional interrupts (SEFIs). Dynamic testing has shown the effectiveness and value of Triple Module Redundancy (TMR) and partial reconfiguration when used in conjunction. Continuing dynamic testing for more complex designs and other Virtex 2 capabilities (i.e., I/O standards, digital clock managers (DCM), etc.) is scheduled.

Design study and performance analysis of a high-speed multistage variable-geometry fan for a variable cycle engine

NASA Technical Reports Server (NTRS)

Sullivan, T. J.; Parker, D. E.

1979-01-01

A design technology study was performed to identify a high speed, multistage, variable geometry fan configuration capable of achieving wide flow modulation with near optimum efficiency at the important operating condition. A parametric screening study of the front and rear block fans was conducted in which the influence of major fan design features on weight and efficiency was determined. Key design parameters were varied systematically to determine the fan configuration most suited for a double bypass, variable cycle engine. Two and three stage fans were considered for the front block. A single stage, core driven fan was studied for the rear block. Variable geometry concepts were evaluated to provide near optimum off design performance. A detailed aerodynamic design and a preliminary mechanical design were carried out for the selected fan configuration. Performance predictions were made for the front and rear block fans.

Warrior Injury Assessment Manikin (WIAMan) Lumbar Spine Model Validation: Development, Testing, and Analysis of Physical and Computational Models of the WIAMan Lumbar Spine Materials Demonstrator

DTIC Science & Technology

2016-08-01

load. The 1 and 10 s-1 rate tests were run on a hydraulic high-rate Instron MTS (8821S), placed in a custom- designed tension fixture (Fig. 8...lateral compression prior to shear testing . The sides of the coupon rest on blocks at the bottom of the vice jaw to allow for travel of the center post ...mode of failure based on the lap shear testing . However, since the pretest spine survived all hits at the BRC speeds, it was decided to proceed with

Biological materials by design.

PubMed

Qin, Zhao; Dimas, Leon; Adler, David; Bratzel, Graham; Buehler, Markus J

2014-02-19

In this topical review we discuss recent advances in the use of physical insight into the way biological materials function, to design novel engineered materials 'from scratch', or from the level of fundamental building blocks upwards and by using computational multiscale methods that link chemistry to material function. We present studies that connect advances in multiscale hierarchical material structuring with material synthesis and testing, review case studies of wood and other biological materials, and illustrate how engineered fiber composites and bulk materials are designed, modeled, and then synthesized and tested experimentally. The integration of experiment and simulation in multiscale design opens new avenues to explore the physics of materials from a fundamental perspective, and using complementary strengths from models and empirical techniques. Recent developments in this field illustrate a new paradigm by which complex material functionality is achieved through hierarchical structuring in spite of simple material constituents.

Electronic design of a multichannel programmable implant for neuromuscular electrical stimulation.

PubMed

Arabi, K; Sawan, M A

1999-06-01

An advanced stimulator for neuromuscular stimulation of spinal cord injured patients has been developed. The stimulator is externally controlled and powered by a single encoded radio frequency carrier and has four independently controlled bipolar stimulation channels. It offers a wide range of reprogrammability and flexibility, and can be used in many neuromuscular electrical stimulation applications. The implant system is adaptable to patient's needs and to future developments in stimulation algorithms by reprogramming the stimulator. The stimulator is capable of generating a wide range of stimulation waveforms and stimulation patterns and therefore is very suitable for selective nerve stimulation techniques. The reliability of the implant has been increased by using a forward error detection and correction communication protocol and by designing the chip for structural testability based on scan test approach. Implemented testability scheme makes it possible to verify the complete functionality of the implant before and after implantation. The stimulators architecture is designed to be modular and therefore its different blocks can be reused as standard building blocks in the design and implementation of other neuromuscular prostheses. Design for low-power techniques have also been employed to reduce power consumption of the electronic circuitry.

Efficiency of a borehole seal by means of pre-compacted bentonite blocks

NASA Astrophysics Data System (ADS)

Van Geet, M.; Volckaert, G.; Bastiaens, W.; Maes, N.; Weetjens, E.; Sillen, X.; Vallejan, B.; Gens, A.

The backfilling and sealing of shafts and galleries is an essential part of the design of underground repositories for high-level radioactive waste. Part of the EC funded project RESEAL studied the feasibility of sealing off a borehole in plastic Boom Clay by means of pre-compacted bentonite blocks. Two bentonites, namely the FoCa and Serrata clay, have been used. Based on laboratory tests, the bentonite blocks had an initial dry density of about 1.8 g/cm 3 to obtain a swelling pressure of about 4.4 MPa, corresponding to the in situ lithostatic stress, at full saturation. The set-up was equipped with several sensors to follow-up the behaviour of the seal and the surrounding host rock during hydration. Full saturation was reached after five months and was mainly reached by natural hydration. Swelling pressure was lower than originally foreseen due to the slow reconsolidation of the host rock. Later on, the efficiency of the seal with respect to water, gas and radionuclide migration was tested. The in situ measured permeability of the seals was about 5 × 10 -13 m/s. A gas breakthrough experiment did not show any preferential gas migration through the seal. No evidences of a preferential pathway could be detected from 125I tracer test results.

Conservation of ectomycorrhizal fungi: green-tree retention preserves species diversity

Treesearch

Joyce L. Eberhart; Daniel L. Luoma

2013-01-01

Th e Demonstration of Ecosystem Management Options (DEMO) project is a large, interdisciplinary study designed to test the biological and silvicultural eff ects of green-tree retention in Douglas-fi r (Pseudotsuga menziesii) forests. Six treatments were replicated on six blocks in Washington and Oregon, USA: no harvest, 75 percent aggregated, 40 percent (dispersed and...

Chemistry Lectures and Laboratories. A Model to Improve Preservice Elementary Science Teacher Development. Volume III.

ERIC Educational Resources Information Center

Crosby, Glenn; And Others

A group of scientists and science educators of Washington State University has developed and pilot tested an integrated physical science program designed for preservice elementary school teachers. This document includes the syllabus and class materials for the Chemistry block of the physical science courses developed by the group. Included are…

"Life Stage-Specific" Variations in Performance in Response to Age Stereotypes

ERIC Educational Resources Information Center

Hehman, Jessica A.; Bugental, Daphne Blunt

2013-01-01

In a test of life stage-specific responses to age-based stigma, older (n = 54, ages 62-92) and younger (n = 81, ages 17-22) adults were told that a task (Weschler Adult Intelligence Scale-III block design) required either (a) speed/contemporary knowledge (YA; "youth advantage") or (b) life experience/wisdom (OA; "age…

Effects of Tutorial Interventions in Mathematics and Attention for Low-Performing Preschool Children

ERIC Educational Resources Information Center

Barnes, Marcia A.; Klein, Alice; Swank, Paul; Starkey, Prentice; McCandliss, Bruce; Flynn, Kylie; Zucker, Tricia; Huang, Chun-Wei; Fall, Anna-Mária; Roberts, Greg

2016-01-01

Two intervention approaches designed to address the multifaceted academic and cognitive difficulties of low-income children who enter pre-K with very low math knowledge were tested in a randomized experiment. Blocking on classroom, children who met screening criteria were assigned to a Math + Attention condition in which the Pre-Kindergarten…

Geology Lectures and Laboratories. A Model to Improve Preservice Elementary Science Teacher Development. Volume IV.

ERIC Educational Resources Information Center

Webster, Gary

A group of scientists and science educators at Washington State University has developed and pilot tested an integrated physical science program designed for preservice elementary school teachers. This document includes the syllabus and class materials for the Geology block of the physical science courses developed by the group. Included are…

Astronomy Lectures and Laboratories. A Model to Improve Preservice Elementary Science Teacher Development. Volume I.

ERIC Educational Resources Information Center

Lutz, Julie H.; Orlich, Donald C.

A group of scientists and science educators at Washington State University has developed and pilot tested an integrated physical science program designed for preservice elementary school teachers. This document includes the syllabus and class materials for the Astronomy block of the physical science courses developed by the group. Included are…

Development of deployable structures for large space platform systems. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Greenberg, H. S.

1983-01-01

The preponderance of study effort was devoted toward the deployable platform systems study which culminated in the detailed design of a ground test article for future development testing. This design is representative of a prototype square-truss, single-fold building-block design that can construct deployable platform structures. This prototype design was selected through a comprehensive and traceable selection process applied to eight competitive designs. The selection process compared the competitive designs according to seven major selection criteria, i.e., design versatility, cost, thermal stability, meteoroid impact significance, reliability, performance predictability, and orbiter integration suitability. In support of the foregoing, a materials data base, and platform systems technology development needs were established. An erectable design of an OTV hangar was selected and recommended for further design development. This design was selected from five study-developed competitive single-fold and double-fold designs including hard-shell and inflatable designs. Also, two deployable manned module configurations, i.e., a hard-shell and an inflatable design were each developed to the same requirements as the composite of two Space station baseline habitat modules.

Investigation of charge coupled device correlation techniques

NASA Technical Reports Server (NTRS)

Lampe, D. R.; Lin, H. C.; Shutt, T. J.

1978-01-01

Analog Charge Transfer Devices (CTD's) offer unique advantages to signal processing systems, which often have large development costs, making it desirable to define those devices which can be developed for general system's use. Such devices are best identified and developed early to give system's designers some interchangeable subsystem blocks, not requiring additional individual development for each new signal processing system. The objective of this work is to describe a discrete analog signal processing device with a reasonably broad system use and to implement its design, fabrication, and testing.

Control/structure interaction design methodology

NASA Technical Reports Server (NTRS)

Briggs, Hugh C.; Layman, William E.

1989-01-01

The Control Structure Interaction Program is a technology development program for spacecraft that exhibit interactions between the control system and structural dynamics. The program objectives include development and verification of new design concepts (such as active structure) and new tools (such as a combined structure and control optimization algorithm) and their verification in ground and possibly flight test. The new CSI design methodology is centered around interdisciplinary engineers using new tools that closely integrate structures and controls. Verification is an important CSI theme and analysts will be closely integrated to the CSI Test Bed laboratory. Components, concepts, tools and algorithms will be developed and tested in the lab and in future Shuttle-based flight experiments. The design methodology is summarized in block diagrams depicting the evolution of a spacecraft design and descriptions of analytical capabilities used in the process. The multiyear JPL CSI implementation plan is described along with the essentials of several new tools. A distributed network of computation servers and workstations was designed that will provide a state-of-the-art development base for the CSI technologies.

Design of an MR image processing module on an FPGA chip.

PubMed

Li, Limin; Wyrwicz, Alice M

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128×128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. Copyright © 2015 Elsevier Inc. All rights reserved.

An efficient HW and SW design of H.264 video compression, storage and playback on FPGA devices for handheld thermal imaging systems

NASA Astrophysics Data System (ADS)

Gunay, Omer; Ozsarac, Ismail; Kamisli, Fatih

2017-05-01

Video recording is an essential property of new generation military imaging systems. Playback of the stored video on the same device is also desirable as it provides several operational benefits to end users. Two very important constraints for many military imaging systems, especially for hand-held devices and thermal weapon sights, are power consumption and size. To meet these constraints, it is essential to perform most of the processing applied to the video signal, such as preprocessing, compression, storing, decoding, playback and other system functions on a single programmable chip, such as FPGA, DSP, GPU or ASIC. In this work, H.264/AVC (Advanced Video Coding) compatible video compression, storage, decoding and playback blocks are efficiently designed and implemented on FPGA platforms using FPGA fabric and Altera NIOS II soft processor. Many subblocks that are used in video encoding are also used during video decoding in order to save FPGA resources and power. Computationally complex blocks are designed using FPGA fabric, while blocks such as SD card write/read, H.264 syntax decoding and CAVLC decoding are done using NIOS processor to benefit from software flexibility. In addition, to keep power consumption low, the system was designed to require limited external memory access. The design was tested using 640x480 25 fps thermal camera on CYCLONE V FPGA, which is the ALTERA's lowest power FPGA family, and consumes lower than 40% of CYCLONE V 5CEFA7 FPGA resources on average.

Development of Aspherical Active Gratings at NSRRC

NASA Astrophysics Data System (ADS)

Tseng, Tse-Chuan; Wang, Duan Jen; Perng, Shen-Yaw; Chen, Chien-Te; Lin, Chia-Jui; Kuan, Chien-Kuang; Ho, His-Chou; Wang, Jeremy; Fung, H. S.; Chang, Shuo-Hung

2007-01-01

An active grating based on a novel optical concept with bendable polynomial surface profile to reduce the coma and defocus aberrations had been designed and proved by the prototype testing. Due to the low glass transition temperature of the glue and the difference of thermal expansion coefficient between the 17-4 steel bender and silicon, the prototype distorted from flat polished condition when thermally de-blocked the polishing pitch. To improve the thermal deformation of the active grating in the polishing process, a new invar bender and high curing temperature glue were adapted to glue a silicon substrate on the bender. After some tests and manufacturer polishing, it showed acceptable conditions. In this paper we will present the design and preliminary tests of the invar active grating. Meanwhile, the design and analysis of a new 17-4 PH steel bender to be electro-less nickel plating and mechanical ruling for a new beamline will also be discussed.

A Lower-Cost High-Resolution LYSO Detector Development for Positron Emission Mammography (PEM)

PubMed Central

Ramirez, Rocio A.; Zhang, Yuxuan; Liu, Shitao; Li, Hongdi; Baghaei, Hossain; An, Shaohui; Wang, Chao; Jan, Meei-Ling; Wong, Wai-Hoi

2010-01-01

In photomultiplier-quadrant-sharing (PQS) geometry for positron emission tomography applications, each PMT is shared by four blocks and each detector block is optically coupled to four round PMTs. Although this design reduces the cost of high-resolution PET systems, when the camera consists of detector panels that are made up of square blocks, half of the PMT’s sensitive window remains unused at the detector panel edge. Our goal was to develop a LYSO detector panel which minimizes the unused portion of the PMTs for a low-cost, high-resolution, and high-sensitivity positron emission mammography (PEM) camera. We modified the PQS design by using elongated blocks at panel edges and square blocks in the inner area. For elongated blocks, symmetric and asymmetrical reflector patterns were developed and PQS and PMT-half-sharing (PHS) arrangements were implemented in order to obtain a suitable decoding. The packing fraction was 96.3% for asymmetric block and 95.5% for symmetric block. Both of the blocks have excellent decoding capability with all crystals clearly identified, 156 for asymmetric and 144 for symmetric and peak-to-valley ratio of 3.0 and 2.3 respectively. The average energy resolution was 14.2% for the asymmetric block and 13.1% for the symmetric block. Using a modified PQS geometry and asymmetric block design, we reduced the unused PMT region at detector panel edges, thereby increased the field-of-view and the overall detection sensitivity and minimized the undetected breast region near the chest wall. This detector design and using regular round PMT allowed building a lower-cost, high-resolution and high-sensitivity PEM camera. PMID:20485510

Acceleration of block-matching algorithms using a custom instruction-based paradigm on a Nios II microprocessor

NASA Astrophysics Data System (ADS)

González, Diego; Botella, Guillermo; García, Carlos; Prieto, Manuel; Tirado, Francisco

2013-12-01

This contribution focuses on the optimization of matching-based motion estimation algorithms widely used for video coding standards using an Altera custom instruction-based paradigm and a combination of synchronous dynamic random access memory (SDRAM) with on-chip memory in Nios II processors. A complete profile of the algorithms is achieved before the optimization, which locates code leaks, and afterward, creates a custom instruction set, which is then added to the specific design, enhancing the original system. As well, every possible memory combination between on-chip memory and SDRAM has been tested to achieve the best performance. The final throughput of the complete designs are shown. This manuscript outlines a low-cost system, mapped using very large scale integration technology, which accelerates software algorithms by converting them into custom hardware logic blocks and showing the best combination between on-chip memory and SDRAM for the Nios II processor.

Use of simulation to compare the performance of minimization with stratified blocked randomization.

PubMed

Toorawa, Robert; Adena, Michael; Donovan, Mark; Jones, Steve; Conlon, John

2009-01-01

Minimization is an alternative method to stratified permuted block randomization, which may be more effective at balancing treatments when there are many strata. However, its use in the regulatory setting for industry trials remains controversial, primarily due to the difficulty in interpreting conventional asymptotic statistical tests under restricted methods of treatment allocation. We argue that the use of minimization should be critically evaluated when designing the study for which it is proposed. We demonstrate by example how simulation can be used to investigate whether minimization improves treatment balance compared with stratified randomization, and how much randomness can be incorporated into the minimization before any balance advantage is no longer retained. We also illustrate by example how the performance of the traditional model-based analysis can be assessed, by comparing the nominal test size with the observed test size over a large number of simulations. We recommend that the assignment probability for the minimization be selected using such simulations. Copyright (c) 2008 John Wiley & Sons, Ltd.

Effects of Interlocking and Supporting Conditions on Concrete Block Pavements

NASA Astrophysics Data System (ADS)

Mahapatra, Geetimukta; Kalita, Kuldeep

2018-02-01

Concrete Block Paving (CBP) is widely used as wearing course in flexible pavements, preferably under light and medium vehicular loadings. Construction of CBP at site is quick and easy in quality control. Usually, flexible pavement design philosophy is followed in CBP construction, though it is structurally different in terms of small block elements with high strength concrete and their interlocking aspects, frequent joints and discontinuity, restrained edge etc. Analytical solution for such group action of concrete blocks under loading in a three dimensional multilayer structure is complex and thus, the need of conducting experimental studies is necessitated for extensive understanding of the load—deformation characteristics and behavior of concrete blocks in pavement. The present paper focuses on the experimental studies for load transfer characteristics of CBP under different interlocking and supporting conditions. It is observed that both interlocking and supporting conditions affect significantly on the load transfer behavior in CBP structures. Coro-lock block exhibits better performance in terms of load carrying capacity and distortion behavior under static loads. Plate load tests are performed over subgrade, granular sub-base (GSB), CBP with and without GSB using different block shapes. For an example case, the comparison of CBP with conventional flexible pavement section is also presented and it is found that CBP provides considerable benefit in terms of construction cost of the road structure.

How Young Children Learn to Program with Sensor, Action, and Logic Blocks

ERIC Educational Resources Information Center

Wyeth, Peta

2008-01-01

Electronic Blocks are a new programming environment designed specifically for children aged between 3 and 8 years. These physical, stackable blocks include sensor blocks, action blocks, and logic blocks. By connecting these blocks, children can program a wide variety of structures that interact with one another and the environment. Electronic…

Learning Design at White Sands Test Facility

NASA Technical Reports Server (NTRS)

Grotewiel, Shane

2010-01-01

During the Fall of 2010, I spent my time at NASA White Sands Test Facility in Las Cruces, NM as an Undergraduate Student Research Program (USRP) Intern. During that time, I was given three projects to work on: Large Altitude Simulation System (LASS) basket strainer, log books, and the design of a case for touch screen monitors used for simulations. I spent most of my time on the LASS basket strainer. The LASS system has a water feed line with a basket strainer that filters out rust. In 2009, there were three misfires which cost approximately $27,000 and about 8% of the allotted time. The strainer was getting a large change in pressure that would result in a shutdown of the system. I have designed a new basket that will eliminate the large pressure change and it can be used with the old basket strainer housing. The LASS system has three steam generators (modules). Documents pertaining to these modules are stored electronically, and the majority of the documents are not able to be searched with keywords, so they have to be gone through one by one. I have come up with an idea on how to organize these files so that the Propulsion Department may efficiently search through the documents needed. Propulsion also has a LASS simulator that incorporates two touch screen monitors. Currently these monitors are in six foot by two foot metal cabinet on wheels. During simulation these monitors are used in the block house and need to be taken out of the block house when not in use. I have designed different options for hand held cases for storing and transporting the monitors in and out of the block house. The three projects previously mentioned demonstrate my contributions to the Propulsion Department and have taught me real world experience that is essential in becoming a productive engineer.

Does erotic stimulus presentation design affect brain activation patterns? Event-related vs. blocked fMRI designs.

PubMed

Bühler, Mira; Vollstädt-Klein, Sabine; Klemen, Jane; Smolka, Michael N

2008-07-22

Existing brain imaging studies, investigating sexual arousal via the presentation of erotic pictures or film excerpts, have mainly used blocked designs with long stimulus presentation times. To clarify how experimental functional magnetic resonance imaging (fMRI) design affects stimulus-induced brain activity, we compared brief event-related presentation of erotic vs. neutral stimuli with blocked presentation in 10 male volunteers. Brain activation differed depending on design type in only 10% of the voxels showing task related brain activity. Differences between blocked and event-related stimulus presentation were found in occipitotemporal and temporal regions (Brodmann Area (BA) 19, 37, 48), parietal areas (BA 7, 40) and areas in the frontal lobe (BA 6, 44). Our results suggest that event-related designs might be a potential alternative when the core interest is the detection of networks associated with immediate processing of erotic stimuli.Additionally, blocked, compared to event-related, stimulus presentation allows the emergence and detection of non-specific secondary processes, such as sustained attention, motor imagery and inhibition of sexual arousal.

Does erotic stimulus presentation design affect brain activation patterns? Event-related vs. blocked fMRI designs

PubMed Central

Bühler, Mira; Vollstädt-Klein, Sabine; Klemen, Jane; Smolka, Michael N

2008-01-01

Background Existing brain imaging studies, investigating sexual arousal via the presentation of erotic pictures or film excerpts, have mainly used blocked designs with long stimulus presentation times. Methods To clarify how experimental functional magnetic resonance imaging (fMRI) design affects stimulus-induced brain activity, we compared brief event-related presentation of erotic vs. neutral stimuli with blocked presentation in 10 male volunteers. Results Brain activation differed depending on design type in only 10% of the voxels showing task related brain activity. Differences between blocked and event-related stimulus presentation were found in occipitotemporal and temporal regions (Brodmann Area (BA) 19, 37, 48), parietal areas (BA 7, 40) and areas in the frontal lobe (BA 6, 44). Conclusion Our results suggest that event-related designs might be a potential alternative when the core interest is the detection of networks associated with immediate processing of erotic stimuli. Additionally, blocked, compared to event-related, stimulus presentation allows the emergence and detection of non-specific secondary processes, such as sustained attention, motor imagery and inhibition of sexual arousal. PMID:18647397

Mechanical Testing of IN718 Lattice Block Structures

NASA Technical Reports Server (NTRS)

Krause, David L.; Whittenberger, John D.; Kantzos, Pete T.; Hebsur, Mohan G.

2002-01-01

Lattice block construction produces a flat, structurally rigid panel composed of thin ligaments of material arranged in a three-dimensional triangulated truss-like structure. Low-cost methods of producing cast metallic lattice block panels are now available that greatly expand opportunities for using this unique material system in today's high-performance structures. Additional advances are being made in NASA's Ultra Efficient Engine Technology (UEET) program to extend the lattice block concept to superalloy materials. Advantages offered by this combination include high strength, light weight, high stiffness, and elevated temperature capabilities. Recently under UEET, the nickel-based superalloy Inconel 718 (IN718) was investment cast into lattice block panels with great success. To evaluate casting quality and lattice block architecture merit, individual ligaments, and structural subelement specimens were extracted from the panels. Tensile tests, structural compression, and bending strength tests were performed on these specimens. Fatigue testing was also completed for several bend test specimens. This paper first presents metallurgical and optical microscopy analysis of the castings. This is followed by mechanical test results for the tensile ligament tests and the subelement compression and bending strength tests, as well as for the fatigue tests that were performed. These tests generally showed comparable properties to base IN718 with the same heat treatment, and they underscored the benefits offered by lattice block materials. These benefits might be extended with improved architecture such as face sheets.

A Numerical Approach to the Accretion of Micro-Continental Blocks and Subsequent Subduction Initiation

NASA Astrophysics Data System (ADS)

Gün, E.; Gogus, O.; Pysklywec, R.; Topuz, G.; Bodur, O. F.

2017-12-01

The Tethyan belt in the eastern Mediterranean region is characterized by the accretion of several micro-continental blocks (e.g. Anatolide-Tauride, Sakarya and Istanbul terranes). The accretion of a micro-continental block to the active continental margin and subsequent initiation of a new subduction are of crucial importance in understanding the geodynamic evolution of the region. Numerical geodynamic experiments are designed to investigate how these micro-continental blocks in the ocean-continent subduction system develops the aforementioned subduction, back-arc extension, surface uplift and the ophiolite emplacement in the eastern Mediterranean since Late Cretaceous. In a series set of experiments, we test various sizes of micro-continental blocks (ranging from 50 to 300 km), different rheological properties (e.g. dry-wet olivine mantle) and imposed plate convergence velocities (0 to 4 cm/year). For a prime present-day analogue to the micro-continental block collision-accretion, model predictions are compared against the collision between Eratosthenes and Cyprus. Preliminary results show that slab break-off occurs directly after the collision when the plate convergence velocities are less than 2 cm/yr and the mantle lithosphere of the continental block has viscoplastic rheology. On the other hand, there is no relationship between convergence rate and break-off event when the lithospheric mantle rheology is chosen to be plastic. Furthermore, the micro-continental block undergoes considerable extension before continental collision due to the slab pull force, if a viscoplastic rheology is assumed for the mantle lithosphere.

Active member vibration control experiment in a KC-135 reduced gravity environment

NASA Technical Reports Server (NTRS)

Lawrence, C. R.; Lurie, B. J.; Chen, G.-S.; Swanson, A. D.

1991-01-01

An active member vibration control experiment in a KC-135 reduced gravity environment was carried out by the Air Force Flight Dynamics Laboratory and the Jet Propulsion Laboratory. Two active members, consisting of piezoelectric actuators, displacement sensors, and load cells, were incorporated into a 12-meter, 104 kg box-type test structure. The active member control design involved the use of bridge (compound) feedback concept, in which the collocated force and velocity signals are feedback locally. An impact-type test was designed to accommodate the extremely short duration of the reduced gravity testing window in each parabolic flight. The moving block analysis technique was used to estimate the modal frequencies and dampings from the free-decay responses. A broadband damping performance was demonstrated up to the ninth mode of 40 Hz. The best damping performance achieved in the flight test was about 5 percent in the fourth mode of the test structure.

Conditional Monte Carlo randomization tests for regression models.

PubMed

Parhat, Parwen; Rosenberger, William F; Diao, Guoqing

2014-08-15

We discuss the computation of randomization tests for clinical trials of two treatments when the primary outcome is based on a regression model. We begin by revisiting the seminal paper of Gail, Tan, and Piantadosi (1988), and then describe a method based on Monte Carlo generation of randomization sequences. The tests based on this Monte Carlo procedure are design based, in that they incorporate the particular randomization procedure used. We discuss permuted block designs, complete randomization, and biased coin designs. We also use a new technique by Plamadeala and Rosenberger (2012) for simple computation of conditional randomization tests. Like Gail, Tan, and Piantadosi, we focus on residuals from generalized linear models and martingale residuals from survival models. Such techniques do not apply to longitudinal data analysis, and we introduce a method for computation of randomization tests based on the predicted rate of change from a generalized linear mixed model when outcomes are longitudinal. We show, by simulation, that these randomization tests preserve the size and power well under model misspecification. Copyright © 2014 John Wiley & Sons, Ltd.

Phase I Final Scientific Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Xijia; Fetvedt, Jeremy; Dimmig, Walker

This Final Scientific Report addresses the accomplishments achieved during Phase I of DE- FE0023985, Coal Syngas Combustor Development for Supercritical CO 2 Power Cycles. The primary objective of the project was to develop a coal syngas-fueled combustor design for use with high-pressure, high-temperature, oxy-fuel, supercritical CO 2 power cycles, with particular focus given to the conditions required by the Allam Cycle. The primary goals, from the Statement of Project Objectives, were to develop: (1) a conceptual design of a syngas-fueled combustor-turbine block for a 300MWe high-pressure, oxy-fuel, sCO2 power plant; (2) the preliminary design of a 5MWt test combustor; andmore » (3) the definition of a combustor test program. Accomplishments for each of these goals are discussed in this report.« less

Impact force as a scaling parameter

NASA Technical Reports Server (NTRS)

Poe, Clarence C., Jr.; Jackson, Wade C.

1994-01-01

The Federal Aviation Administration (FAR PART 25) requires that a structure carry ultimate load with nonvisible impact damage and carry 70 percent of limit flight loads with discrete damage. The Air Force has similar criteria (MIL-STD-1530A). Both civilian and military structures are designed by a building block approach. First, critical areas of the structure are determined, and potential failure modes are identified. Then, a series of representative specimens are tested that will fail in those modes. The series begins with tests of simple coupons, progresses through larger and more complex subcomponents, and ends with a test on a full-scale component, hence the term 'building block.' In order to minimize testing, analytical models are needed to scale impact damage and residual strength from the simple coupons to the full-scale component. Using experiments and analysis, the present paper illustrates that impact damage can be better understood and scaled using impact force than just kinetic energy. The plate parameters considered are size and thickness, boundary conditions, and material, and the impact parameters are mass, shape, and velocity.

Solar cell array design handbook, volume 1

NASA Technical Reports Server (NTRS)

Rauschenbach, H. S.

1976-01-01

Twelve chapters discuss the following: historical developments, the environment and its effects, solar cells, solar cell filters and covers, solar cell and other electrical interconnections, blocking and shunt diodes, substrates and deployment mechanisms, material properties, design synthesis and optimization, design analysis, procurement, production and cost aspects, evaluation and test, orbital performance, and illustrative design examples. A comprehensive index permits rapid locating of desired topics. The handbook consists of two volumes: Volume 1 is of an expository nature while Volume 2 contains detailed design data in an appendix-like fashion. Volume 2 includes solar cell performance data, applicable unit conversion factors and physical constants, and mechanical, electrical, thermal optical, magnetic, and outgassing material properties. Extensive references are provided.

Simulating the Response of a Composite Honeycomb Energy Absorber. Part 1; Dynamic Crushing of Components and Multi-Terrain Impacts

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Fasanella, Edwin L.; Polanco, Michael A.

2012-01-01

This paper describes the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar (Registered Trademark) honeycomb to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed until needed for deployment. Experimental evaluation of the DEA included dynamic crush tests of multi-cell components and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto multi-terrain. Finite element models of the test articles were developed and simulations were performed using the transient dynamic code, LSDYNA (Registered Trademark). In each simulation, the DEA was represented using shell elements assigned two different material properties: Mat 24, an isotropic piecewise linear plasticity model, and Mat 58, a continuum damage mechanics model used to represent laminated composite fabrics. DEA model development and test-analysis comparisons are presented.

A Comparison of Jump Height, Takeoff Velocities, and Blocking Coverage in the Swing and Traditional Volleyball Blocking Techniques

PubMed Central

Ficklin, Travis; Lund, Robin; Schipper, Megan

2014-01-01

The purpose of this study was to compare traditional and swing blocking techniques on center of mass (COM) projectile motion and effective blocking area in nine healthy Division I female volleyball players. Two high-definition (1080 p) video cameras (60 Hz) were used to collect two-dimensional variables from two separate views. One was placed perpendicular to the plane of the net and the other was directed along the top of the net, and were used to estimate COM locations and blocking area in a plane parallel to the net and hand penetration through the plane of the net respectively. Video of both the traditional and swing techniques were digitized and kinematic variables were calculated. Paired samples t-tests indicated that the swing technique resulted in greater (p < 0.05) vertical and horizontal takeoff velocities (vy and vx), jump height (H), duration of the block (tBLOCK), blocking coverage during the block (C) as well as hand penetration above and through the net’s plane (YPEN, ZPEN). The traditional technique had significantly greater approach time (tAPP). The results of this study suggest that the swing technique results in both greater jump height and effective blocking area. However, the shorter tAPP that occurs with swing is associated with longer times in the air during the block which may reduce the ability of the athlete to make adjustments to attacks designed to misdirect the defense. Key Points Swing blocking technique has greater jump height, effective blocking area, hand penetration, horizontal and vertical takeoff velocity, and has a shorter time of approach. Despite these advantages, there may be more potential for mistiming blocks and having erratic deflections of the ball after contact when using the swing technique. Coaches should take more than simple jump height and hand penetration into account when deciding which technique to employ. PMID:24570609

A comparison of jump height, takeoff velocities, and blocking coverage in the swing and traditional volleyball blocking techniques.

PubMed

Ficklin, Travis; Lund, Robin; Schipper, Megan

2014-01-01

The purpose of this study was to compare traditional and swing blocking techniques on center of mass (COM) projectile motion and effective blocking area in nine healthy Division I female volleyball players. Two high-definition (1080 p) video cameras (60 Hz) were used to collect two-dimensional variables from two separate views. One was placed perpendicular to the plane of the net and the other was directed along the top of the net, and were used to estimate COM locations and blocking area in a plane parallel to the net and hand penetration through the plane of the net respectively. Video of both the traditional and swing techniques were digitized and kinematic variables were calculated. Paired samples t-tests indicated that the swing technique resulted in greater (p < 0.05) vertical and horizontal takeoff velocities (vy and vx), jump height (H), duration of the block (tBLOCK), blocking coverage during the block (C) as well as hand penetration above and through the net's plane (YPEN, ZPEN). The traditional technique had significantly greater approach time (tAPP). The results of this study suggest that the swing technique results in both greater jump height and effective blocking area. However, the shorter tAPP that occurs with swing is associated with longer times in the air during the block which may reduce the ability of the athlete to make adjustments to attacks designed to misdirect the defense. Key PointsSwing blocking technique has greater jump height, effective blocking area, hand penetration, horizontal and vertical takeoff velocity, and has a shorter time of approach.Despite these advantages, there may be more potential for mistiming blocks and having erratic deflections of the ball after contact when using the swing technique.Coaches should take more than simple jump height and hand penetration into account when deciding which technique to employ.

Design, fabrication, test, and qualification and price analysis of third generation design solar cell modules

NASA Astrophysics Data System (ADS)

Shepard, N. F.

1980-03-01

The Block 4 shingle type module makes it possible to apply a photovoltaic array to the sloping roof of a residential building by simply nailing the overlapping hexagon shaped shingles to the plywood roof sheathing. This third-generation shingle module design consists of nineteen series connected 100 mm diameter solar cells which are arranged in a closely packed hexagon configuration to provide in excess of 75 watts/sq m of exposed module area under standard operating conditions. The solar cells are individually bonded to the embossed underside of a 4.4 mm thick thermally tempered piece of glass. An experimental silicone pottant was used as the transparent bonding adhesive between the cells and glass. The semi-flexible portion of each shingle module is a composite laminate construction consisting of an outer layer of FLEXSEAL bonded to an inner core of closed cell polyethylene foam. Silaprene is used as the substrate laminating adhesive. The module design has satisfactorily survived qualification testing program which includes 50 thermal cycles between -40 and +90 C, a seven day temperature-humidity exposure test, and a wind resistance test.

Design, fabrication, test, and qualification and price analysis of third generation design solar cell modules

NASA Technical Reports Server (NTRS)

Shepard, N. F.

1980-01-01

The Block 4 shingle type module makes it possible to apply a photovoltaic array to the sloping roof of a residential building by simply nailing the overlapping hexagon shaped shingles to the plywood roof sheathing. This third-generation shingle module design consists of nineteen series connected 100 mm diameter solar cells which are arranged in a closely packed hexagon configuration to provide in excess of 75 watts/sq m of exposed module area under standard operating conditions. The solar cells are individually bonded to the embossed underside of a 4.4 mm thick thermally tempered piece of glass. An experimental silicone pottant was used as the transparent bonding adhesive between the cells and glass. The semi-flexible portion of each shingle module is a composite laminate construction consisting of an outer layer of FLEXSEAL bonded to an inner core of closed cell polyethylene foam. Silaprene is used as the substrate laminating adhesive. The module design has satisfactorily survived qualification testing program which includes 50 thermal cycles between -40 and +90 C, a seven day temperature-humidity exposure test, and a wind resistance test.

Traffic sign recognition based on deep convolutional neural network

NASA Astrophysics Data System (ADS)

Yin, Shi-hao; Deng, Ji-cai; Zhang, Da-wei; Du, Jing-yuan

2017-11-01

Traffic sign recognition (TSR) is an important component of automated driving systems. It is a rather challenging task to design a high-performance classifier for the TSR system. In this paper, we propose a new method for TSR system based on deep convolutional neural network. In order to enhance the expression of the network, a novel structure (dubbed block-layer below) which combines network-in-network and residual connection is designed. Our network has 10 layers with parameters (block-layer seen as a single layer): the first seven are alternate convolutional layers and block-layers, and the remaining three are fully-connected layers. We train our TSR network on the German traffic sign recognition benchmark (GTSRB) dataset. To reduce overfitting, we perform data augmentation on the training images and employ a regularization method named "dropout". The activation function we employ in our network adopts scaled exponential linear units (SELUs), which can induce self-normalizing properties. To speed up the training, we use an efficient GPU to accelerate the convolutional operation. On the test dataset of GTSRB, we achieve the accuracy rate of 99.67%, exceeding the state-of-the-art results.

Single event upset suspectibility testing of the Xilinx Virtex II FPGA

NASA Technical Reports Server (NTRS)

Carmichael, C.; Swift, C.; Yui, G.

2002-01-01

Heavy ion testing of the Xilinx Virtex II was conducted on the configuration, block RAM and user flip flop cells to determine their static single-event upset susceptibility using LETs of 1.2 to 60 MeVcm^2/mg. A software program specifically designed to count errors in the FPGA was used to reveal L1/e, values (the LET at which the cross section is l/e times the saturation cross-section) and single-event functional-interrupt failures.

Evaluation of Eye Protection Filters Used with Broad-Spectrum and Conventional LED Curing Lights.

PubMed

Soares, Carlos José; Rodrigues, Monise de Paula; Vilela, Andomar Bruno Fernandes; Rizo, Erick René Cerda; Ferreira, Lorraine Braga; Giannini, Marcelo; Price, Richard Bengt

2017-01-01

The high irradiance and the different emission spectra from contemporary light curing units (LCU) may cause ocular damage. This study evaluated the ability of 15 eye protection filters: 2 glasses, 1 paddle design, and 12 dedicated filters to block out harmful light from a monowave (HP-3M ESPE) and a broad-spectrum (Valo, Ultradent) LED LCU. Using the anterior sensor in the MARC-Patient Simulator (BlueLight Analytics) the irradiance that was delivered through different eye protection filters was measured three times. The LCUs delivered a similar irradiance to the top of the filter. The mean values of the light that passed through the filters as percent of the original irradiance were analyzed using two-way ANOVA followed by Tukey test (a= 0.05). The emission spectra from the LCUs and through the filters were also obtained. Two-way ANOVA showed that the interaction between protective filters and LCUs significantly influenced the amount of light transmitted (p< 0.001). Tukey test showed that the amount of light transmitted through the protective filters when using the HP-3M-ESPE was significantly greater compared to when using the Valo, irrespective of the protective filter tested. When using the HP-3M-ESPE, the Glasses filter allowed significantly more light through, followed by XL 3000, ORTUS, Google Professional, Gnatus filters. The Valo filter was the most effective at blocking out the harmful light. Some protective filters were less effective at blocking the lower wavelengths of light (<420 nm). However, even in the worst scenario, the filters were able to block at least 97% of the irradiance.

Identifying Effective Design Approaches to Allocate Genotypes in Two-Phase Designs: A Case Study in Pelargonium zonale.

PubMed

Molenaar, Heike; Boehm, Robert; Piepho, Hans-Peter

2017-01-01

Robust phenotypic data allow adequate statistical analysis and are crucial for any breeding purpose. Such data is obtained from experiments laid out to best control local variation. Additionally, experiments frequently involve two phases, each contributing environmental sources of variation. For example, in a former experiment we conducted to evaluate production related traits in Pelargonium zonale , there were two consecutive phases, each performed in a different greenhouse. Phase one involved the propagation of the breeding strains to obtain the stem cutting count, and phase two involved the assessment of root formation. The evaluation of the former study raised questions regarding options for improving the experimental layout: (i) Is there a disadvantage to using exactly the same design in both phases? (ii) Instead of generating a separate layout for each phase, can the design be optimized across both phases, such that the mean variance of a pair-wise treatment difference (MVD) can be decreased? To answer these questions, alternative approaches were explored to generate two-phase designs either in phase-wise order (Option 1) or across phases (Option 2). In Option 1 we considered the scenarios (i) using in both phases the same experimental design and (ii) randomizing each phase separately. In Option 2, we considered the scenarios (iii) generating a single design with eight replicates and splitting these among the two phases, (iv) separating the block structure across phases by dummy coding, and (v) design generation with optimal alignment of block units in the two phases. In both options, we considered the same or different block structures in each phase. The designs were evaluated by the MVD obtained by the intra-block analysis and the joint inter-block-intra-block analysis. The smallest MVD was most frequently obtained for designs generated across phases rather than for each phase separately, in particular when both phases of the design were separated with a single pseudo-level. The joint optimization ensured that treatment concurrences were equally balanced across pairs, one of the prerequisites for an efficient design. The proposed alternative approaches can be implemented with any model-based design packages with facilities to formulate linear models for treatment and block structures.

14 CFR 33.99 - General conduct of block tests.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Section 33.99 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.99 General conduct of block... is used for the endurance test it must be subjected to a calibration check before starting the...

14 CFR 33.99 - General conduct of block tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Section 33.99 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.99 General conduct of block... is used for the endurance test it must be subjected to a calibration check before starting the...

14 CFR 33.99 - General conduct of block tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Section 33.99 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.99 General conduct of block... is used for the endurance test it must be subjected to a calibration check before starting the...

14 CFR 33.99 - General conduct of block tests.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Section 33.99 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.99 General conduct of block... is used for the endurance test it must be subjected to a calibration check before starting the...

14 CFR 33.99 - General conduct of block tests.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Section 33.99 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.99 General conduct of block... is used for the endurance test it must be subjected to a calibration check before starting the...

Inverse design of bulk morphologies in block copolymers using particle swarm optimization

NASA Astrophysics Data System (ADS)

Khadilkar, Mihir; Delaney, Kris; Fredrickson, Glenn

Multiblock polymers are a versatile platform for creating a large range of nanostructured materials with novel morphologies and properties. However, achieving desired structures or property combinations is difficult due to a vast design space comprised of parameters including monomer species, block sequence, block molecular weights and dispersity, copolymer architecture, and binary interaction parameters. Navigating through such vast design spaces to achieve an optimal formulation for a target structure or property set requires an efficient global optimization tool wrapped around a forward simulation technique such as self-consistent field theory (SCFT). We report on such an inverse design strategy utilizing particle swarm optimization (PSO) as the global optimizer and SCFT as the forward prediction engine. To avoid metastable states in forward prediction, we utilize pseudo-spectral variable cell SCFT initiated from a library of defect free seeds of known block copolymer morphologies. We demonstrate that our approach allows for robust identification of block copolymers and copolymer alloys that self-assemble into a targeted structure, optimizing parameters such as block fractions, blend fractions, and Flory chi parameters.

Pharmacogenetic excitation of dorsomedial prefrontal cortex restores fear prediction error.

PubMed

Yau, Joanna Oi-Yue; McNally, Gavan P

2015-01-07

Pavlovian conditioning involves encoding the predictive relationship between a conditioned stimulus (CS) and an unconditioned stimulus, so that synaptic plasticity and learning is instructed by prediction error. Here we used pharmacogenetic techniques to show a causal relation between activity of rat dorsomedial prefrontal cortex (dmPFC) neurons and fear prediction error. We expressed the excitatory hM3Dq designer receptor exclusively activated by a designer drug (DREADD) in dmPFC and isolated actions of prediction error by using an associative blocking design. Rats were trained to fear the visual CS (CSA) in stage I via pairings with footshock. Then in stage II, rats received compound presentations of visual CSA and auditory CS (CSB) with footshock. This prior fear conditioning of CSA reduced the prediction error during stage II to block fear learning to CSB. The group of rats that received AAV-hSYN-eYFP vector that was treated with clozapine-N-oxide (CNO; 3 mg/kg, i.p.) before stage II showed blocking when tested in the absence of CNO the next day. In contrast, the groups that received AAV-hSYN-hM3Dq and AAV-CaMKIIα-hM3Dq that were treated with CNO before stage II training did not show blocking; learning toward CSB was restored. This restoration of prediction error and fear learning was specific to the injection of CNO because groups that received AAV-hSYN-hM3Dq and AAV-CaMKIIα-hM3Dq that were injected with vehicle before stage II training did show blocking. These effects were not attributable to the DREADD manipulation enhancing learning or arousal, increasing fear memory strength or asymptotic levels of fear learning, or altering fear memory retrieval. Together, these results identify a causal role for dmPFC in a signature of adaptive behavior: using the past to predict future danger and learning from errors in these predictions. Copyright © 2015 the authors 0270-6474/15/350074-10$15.00/0.

Conceptual design of a 10 to the 8th power bit magnetic bubble domain mass storage unit and fabrication, test and delivery of a feasibility model

NASA Technical Reports Server (NTRS)

1972-01-01

The conceptual design of a highly reliable 10 to the 8th power-bit bubble domain memory for the space program is described. The memory has random access to blocks of closed-loop shift registers, and utilizes self-contained bubble domain chips with on-chip decoding. Trade-off studies show that the highest reliability and lowest power dissipation is obtained when the memory is organized on a bit-per-chip basis. The final design has 800 bits/register, 128 registers/chip, 16 chips/plane, and 112 planes, of which only seven are activated at a time. A word has 64 data bits +32 checkbits, used in a 16-adjacent code to provide correction of any combination of errors in one plane. 100 KHz maximum rotational frequency keeps power low (equal to or less than, 25 watts) and also allows asynchronous operation. Data rate is 6.4 megabits/sec, access time is 200 msec to an 800-word block and an additional 4 msec (average) to a word. The fabrication and operation are also described for a 64-bit bubble domain memory chip designed to test the concept of on-chip magnetic decoding. Access to one of the chip's four shift registers for the read, write, and clear functions is by means of bubble domain decoders utilizing the interaction between a conductor line and a bubble.

Apollo CSM Power Generation System Design Considerations, Failure Modes and Lessons Learned

NASA Technical Reports Server (NTRS)

Interbartolo, Michael

2009-01-01

The objectives of this slide presentation are to: review the basic design criteria for fuel cells (FC's), review design considerations during developmental phase that affected Block I and Block II vehicles, summarize the conditions that led to the failure of components in the FC's, and state the solution implemented for each failure. It reviews the location of the fuel cells, the fuel cell theory the design criteria going into development phase and coming from the development phase, failures and solutions of Block I and II, and the lessons learned.

Feasibility Study for Low Drag Acoustic Liners Final Report

NASA Technical Reports Server (NTRS)

Riedel, Brian; Wu, Jackie

2017-01-01

This report documents the design and structural analysis as a final deliverable for the Phase 1 contract activity. Also included is a community noise test plan, which is a key deliverable for Phase 2. Finally, a high-level estimate (Phase 3 deliverable) is provided for the work statement of Phases 2-4, which covers the build of two inlet test articles, planning and execution of a flight test with the test inlets, as well as data analysis and final documentation. The two test inlets will be compared to the production baseline inlet configuration. There is also a plan to test one of the inlets "hardwalled" using speed tape or some other similar tape to block the acoustic perforations.

A Comparison of Efficacy of Segmental Epidural Block versus Spinal Anaesthesia for Percutaneous Nephrolithotomy.

PubMed

Nandanwar, Avinash S; Patil, Yogita; Wagaskar, Vinayak G; Baheti, Vidyasagar H; Tanwar, Harshwardhan V; Patwardhan, Sujata K

2015-08-01

Percutaneous nephrolithotomy (PCNL) is done under general anaesthesia in most of the centres. Associated complications and cost are higher for general anaesthesia than for regional anaesthesia. Present study is designed to compare the efficacy of epidural block versus spinal anaesthesia with regards to intraoperative mean arterial pressure, heart rate, postoperative pain intensity, analgesic requirement, Postoperative complications and patient satisfaction in patients undergoing PCNL. After taking Ethical Committee clearance, patients were randomly allocated into 2 groups using table of randomization (n= 40 each) Group E- Epidural block, Group S- Spinal block. Various parameters like intraoperative mean arterial pressure, heart rate, postoperative pain intensity, analgesic requirement, postoperative complications and patient satisfaction were studied in these groups. Quantitative data was analysed using unpaired t-test and qualitative data was analysed using chi-square test. Twenty four times in Epidural as compared to fifteen times in spinal anaesthesia two or more attempts required. Mean time (min) required to achieve the block of anaesthesia in group E and group S was 15.45±2.8 and 8.52±2.62 min respectively. Mean arterial pressure (MAP) at 5 min, 10 min and 15 min were significantly lower in spinal group as compared to epidural group. After 30 minutes, differences were not significant but still MAP was lower in spinal group. After 30 minutes difference in heart rate between two groups was statistically significant and higher rate recorded in spinal group till the end of 3 hours. Postoperative VAS score was significantly higher in spinal group and 4 hours onwards difference was highly significant. Postoperative Nausea Vomiting (PONV) Score was significantly higher in spinal group as compared to epidural group. For PCNL, segmental epidural block is better than spinal anaesthesia in terms of haemodynamic stability, postoperative analgesia, patient satisfaction and reduced incidence of PONV. Epidural anaesthesia is difficult to execute and takes longer time to act as compared to spinal block which limits its use.

Six-year performance of 14 Prunus rootstocks at 11 sites in the 2001 NC-140 peach trial

USDA-ARS?s Scientific Manuscript database

Fourteen Prunus rootstock cultivars and selections budded with either ‘Redtop’, ‘Redhaven’ or ‘Cresthaven’ peach [Prunus persica (L.) Batsch] were planted at 11 locations in North America in 2001 in a randomized block design with a tree spacing of 5 by 6 m and 8 replicates. This test planting was a...

A two-stage monolithic buffer amplifier for 20 GHz satellite communication

NASA Technical Reports Server (NTRS)

Petersen, W. C.; Gupta, A. K.

1983-01-01

Design, fabrication, and test results of a two-stage GaAs monolithic buffer amplifier for 20 GHz satellite communication are described in this paper. A gain of 13 + or - 0.75 dB from 17.7 to 20.2 GHz was obtained from the 1.5 x 1.5 millimeter chip, which includes all necessary bias and dc blocking circuitry.

The Role of Play in the Development of Insightful Tool-Using Strategies.

ERIC Educational Resources Information Center

Vandenberg, Brian

This experiment investigates the relation of a free play experience to subsequent performance on problem solving tasks among children aged 4 to 10. Ninety children were divided into 3 age groups and were assigned in pairs of free play and non-play treatment conditions. Children were paired by block design test scores to control for perceptual…

SALT, a dedicated readout chip for high precision tracking silicon strip detectors at the LHCb Upgrade

NASA Astrophysics Data System (ADS)

Bugiel, Sz.; Dasgupta, R.; Firlej, M.; Fiutowski, T.; Idzik, M.; Kuczynska, M.; Moron, J.; Swientek, K.; Szumlak, T.

2016-02-01

The Upstream Tracker (UT) silicon strip detector, one of the central parts of the tracker system of the modernised LHCb experiment, will use a new 128-channel readout ASIC called SALT. It will extract and digitise analogue signals from the UT sensors, perform digital signal processing and transmit a serial output data. The SALT is being designed in CMOS 130 nm process and uses a novel architecture comprising of analog front-end and fast (40 MSps) ultra-low power (<0.5 mW) 6-bit ADC in each channel. The prototype ASICs of important functional blocks, like analogue front-end, 6-bit SAR ADC, PLL, and DLL, were designed, fabricated and tested. A prototype of an 8-channel version of the SALT chip, comprising all important functionalities was also designed and fabricated. The architecture and design of the SALT, together with the selected preliminary tests results, are presented.

Block 2 Solid Rocket Motor (SRM) conceptual design study. Volume 1: Appendices

NASA Technical Reports Server (NTRS)

1986-01-01

The design studies task implements the primary objective of developing a Block II Solid Rocket Motor (SRM) design offering improved flight safety and reliability. The SRM literature was reviewed. The Preliminary Development and Validation Plan is presented.

Predictive and postdictive analysis of forage yield trials

USDA-ARS?s Scientific Manuscript database

Classical experimental design theory, the predominant treatment in most textbooks, promotes the use of blocking designs for control of spatial variability in field studies and other situations in which there is significant variation among heterogeneity among experimental units. Many blocking design...

The Statistical Power of the Cluster Randomized Block Design with Matched Pairs--A Simulation Study

ERIC Educational Resources Information Center

Dong, Nianbo; Lipsey, Mark

2010-01-01

This study uses simulation techniques to examine the statistical power of the group- randomized design and the matched-pair (MP) randomized block design under various parameter combinations. Both nearest neighbor matching and random matching are used for the MP design. The power of each design for any parameter combination was calculated from…

48 CFR 50.205-3 - Authorization of offers contingent upon SAFETY Act designation or certification before contract...

Code of Federal Regulations, 2011 CFR

2011-10-01

...— (i) For offers contingent upon SAFETY Act designation, a pre-qualification designation notice or a block designation; or (ii) For offers contingent upon SAFETY Act certification, a block certification... contingent upon SAFETY Act designation or certification before contract award. 50.205-3 Section 50.205-3...

Solid ground in the wetlands of personality: a reply to Block.

PubMed

Costa, P T; McCrae, R R

1995-03-01

The five-factor model (FFM) of personality offers a structural organization of personality traits in terms of 5 broad factors. J. Block's (1995) critique of the FFM failed to recognize the utility of a trait taxonomy and the intent of research designed to test the 5-factor hypothesis. In a number of instances he omitted reference to empirical evidence that addresses concerns he raised; this evidence shows strong support for the FFM beyond the lexical and questionnaire traditions he reviews. Many of his suggestions for improving the quality of personality research are valuable, but are likely to be more fruitful when used in conjunction with established knowledge about the structure of personality traits: the FFM.

High performance compression of science data

NASA Technical Reports Server (NTRS)

Storer, James A.; Cohn, Martin

1994-01-01

Two papers make up the body of this report. One presents a single-pass adaptive vector quantization algorithm that learns a codebook of variable size and shape entries; the authors present experiments on a set of test images showing that with no training or prior knowledge of the data, for a given fidelity, the compression achieved typically equals or exceeds that of the JPEG standard. The second paper addresses motion compensation, one of the most effective techniques used in the interframe data compression. A parallel block-matching algorithm for estimating interframe displacement of blocks with minimum error is presented. The algorithm is designed for a simple parallel architecture to process video in real time.

Is the red fluorescence of dental plaque related to its cariogenicity?

NASA Astrophysics Data System (ADS)

Bittar, Daniela G.; Pontes, Laura Regina A.; Calvo, Ana Flávia B.; Novaes, Tatiane F.; Braga, Mariana M.; Freitas, Patrícia M.; Tabchoury, Cinthia P. M.; Mendes, Fausto M.

2014-06-01

It has been speculated that the red fluorescence emitted by dental plaque could be related to its cariogenicity. To test this hypothesis, we designed this crossover in situ study, with two experimental phases of 14 days each. Seventeen volunteers, wearing a palatal appliance with bovine enamel blocks, were instructed to drip a 20% sucrose solution (experimental group) or purified water (control group) onto the enamel blocks eight times daily. The specimens were removed after 4, 7, 10, and 14 days, and the red fluorescence of dental plaque formed on the enamel blocks was assessed using a quantitative light-induced fluorescence device. After the plaque removal, surface and cross-sectional microhardness tests were performed to assess the mineral loss. The comparisons were made by a multilevel linear regression analysis. We observed a significant increase in the red fluorescence of the dental plaque after longer periods of formation, but this trend was verified in both groups. The mineral loss assessed by the microhardness techniques, contrariwise, showed a significant increase only in the experimental group. In conclusion, the red fluorescence emitted by the dental plaque indicates a mature biofilm, but this fact is not necessarily associated with its cariogenicity.

Real-Time Evaluation of Breast Self-Examination Using Computer Vision

PubMed Central

Mohammadi, Eman; Dadios, Elmer P.; Gan Lim, Laurence A.; Cabatuan, Melvin K.; Naguib, Raouf N. G.; Avila, Jose Maria C.; Oikonomou, Andreas

2014-01-01

Breast cancer is the most common cancer among women worldwide and breast self-examination (BSE) is considered as the most cost-effective approach for early breast cancer detection. The general objective of this paper is to design and develop a computer vision algorithm to evaluate the BSE performance in real-time. The first stage of the algorithm presents a method for detecting and tracking the nipples in frames while a woman performs BSE; the second stage presents a method for localizing the breast region and blocks of pixels related to palpation of the breast, and the third stage focuses on detecting the palpated blocks in the breast region. The palpated blocks are highlighted at the time of BSE performance. In a correct BSE performance, all blocks must be palpated, checked, and highlighted, respectively. If any abnormality, such as masses, is detected, then this must be reported to a doctor to confirm the presence of this abnormality and proceed to perform other confirmatory tests. The experimental results have shown that the BSE evaluation algorithm presented in this paper provides robust performance. PMID:25435860

Real-time evaluation of breast self-examination using computer vision.

PubMed

Mohammadi, Eman; Dadios, Elmer P; Gan Lim, Laurence A; Cabatuan, Melvin K; Naguib, Raouf N G; Avila, Jose Maria C; Oikonomou, Andreas

2014-01-01

Breast cancer is the most common cancer among women worldwide and breast self-examination (BSE) is considered as the most cost-effective approach for early breast cancer detection. The general objective of this paper is to design and develop a computer vision algorithm to evaluate the BSE performance in real-time. The first stage of the algorithm presents a method for detecting and tracking the nipples in frames while a woman performs BSE; the second stage presents a method for localizing the breast region and blocks of pixels related to palpation of the breast, and the third stage focuses on detecting the palpated blocks in the breast region. The palpated blocks are highlighted at the time of BSE performance. In a correct BSE performance, all blocks must be palpated, checked, and highlighted, respectively. If any abnormality, such as masses, is detected, then this must be reported to a doctor to confirm the presence of this abnormality and proceed to perform other confirmatory tests. The experimental results have shown that the BSE evaluation algorithm presented in this paper provides robust performance.

CODEHOP (COnsensus-DEgenerate Hybrid Oligonucleotide Primer) PCR primer design

PubMed Central

Rose, Timothy M.; Henikoff, Jorja G.; Henikoff, Steven

2003-01-01

We have developed a new primer design strategy for PCR amplification of distantly related gene sequences based on consensus-degenerate hybrid oligonucleotide primers (CODEHOPs). An interactive program has been written to design CODEHOP PCR primers from conserved blocks of amino acids within multiply-aligned protein sequences. Each CODEHOP consists of a pool of related primers containing all possible nucleotide sequences encoding 3–4 highly conserved amino acids within a 3′ degenerate core. A longer 5′ non-degenerate clamp region contains the most probable nucleotide predicted for each flanking codon. CODEHOPs are used in PCR amplification to isolate distantly related sequences encoding the conserved amino acid sequence. The primer design software and the CODEHOP PCR strategy have been utilized for the identification and characterization of new gene orthologs and paralogs in different plant, animal and bacterial species. In addition, this approach has been successful in identifying new pathogen species. The CODEHOP designer (http://blocks.fhcrc.org/codehop.html) is linked to BlockMaker and the Multiple Alignment Processor within the Blocks Database World Wide Web (http://blocks.fhcrc.org). PMID:12824413

76 FR 2193 - Designation Pursuant to Executive Order 13396 of February 7, 2006, “Blocking Property of Certain...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-12

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Designation Pursuant to Executive Order 13396 of February 7, 2006, ``Blocking Property of Certain Persons Contributing to the Conflict in... 7, 2006, ``Blocking Property of Certain Persons Contributing to the Conflict in C[ocirc]te d'Ivoire...

Knowledge and Processes in Design

DTIC Science & Technology

1992-09-03

Orqanization Name(s) and Address(es). Self-explanatory. Block 16. Price Code. Enter approoriate price Block 8. Performing Organization Report code...NTIS on/y). Number. Enter the unique alphanumerc report number(s) assigned by the organization periorming the report. Blocks 17.-19...statement codings were then organized into larger control-flow structures centered around design components called modules. The general assumption was

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozolins, Vidvuds

Molecularly Engineered Energy Materials (MEEM) was established as an interdisciplinary cutting-edge UCLA-based research center uniquely equipped to attack the challenge of rationally designing, synthesizing and testing revolutionary new energy materials. Our mission was to achieve transformational improvements in the performance of materials via controlling the nano-and mesoscale structure using selectively designed, earth-abundant, inexpensive molecular building blocks. MEEM has focused on materials that are inherently abundant, can be easily assembled from intelligently designed building blocks (molecules, nanoparticles), and have the potential to deliver transformative economic benefits in comparison with the current crystalline-and polycrystalline-based energy technologies. MEEM addressed basic science issues relatedmore » to the fundamental mechanisms of carrier generation, energy conversion, as well as transport and storage of charge and mass in tunable, architectonically complex materials. Fundamental understanding of these processes will enable rational design, efficient synthesis and effective deployment of novel three-dimensional material architectures for energy applications. Three interrelated research directions were initially identified where these novel architectures hold great promise for high-reward research: solar energy generation, electrochemical energy storage, and materials for CO 2 capture. Of these, the first two remained throughout the project performance period, while carbon capture was been phased out in consultation and with approval from BES program manager.« less

Design of a surgical instrument for removing bone to provide screw access to a spinal fusion cage.

PubMed

Jabbary Aslani, F; Hukins, D W L; Shepherd, D E T; Parry, J J; Fennell, A J; Lambell, S

2012-01-01

A surgical instrument to aid implantation of a range of lumbar spinal fusion cages has been developed. Once the cage is in position, the entrance to screw holes is partially blocked by the edge of the vertebral body. In order to insert fixation screws to secure the cage between the vertebrae, some part of the blocking edge has to be removed. Rongeurs are currently being used, but they can be time consuming and have the disadvantage that they may remove more bone than is necessary and may cause damage to the fusion cage if not used with care. In addition, access around some of the screw holes may be difficult. The aim of this instrument was to overcome these shortcomings. This paper describes the design of a surgical instrument for cutting edges from vertebral bodies. The development and evaluation of concept designs are presented and discussed. Potential risks were considered and modifications were performed on the selected concept. Functional prototypes were manufactured and tested on sheep lumbar vertebrae. The results showed that the newly designed cutting instrument functions as required and removes the required amount of bone from the vertebral body edge.

Using three-dimensional rapid prototyping in the design and development of orthopaedic screws in standardised pull-out tests.

PubMed

Leslie, Laura Jane; Connolly, Ashley; Swadener, John G; Junaid, Sarah; Theivendran, Kanthan; Deshmukh, Subodh C

2018-06-01

The majority of orthopaedic screws are designed, tested and manufactured by existing orthopaedics companies and are predominantly developed with healthy bone in mind. The timescales and costs involved in the development of a new screw design, for example, for osteoporotic bone, are high. In this study, standard wood screws were used to analyse the concept of using three-dimensional printing, or rapid prototyping, as a viable stage of development in the design of a new bone screw. Six wood screws were reverse engineered and printed in polymeric material using stereolithography. Three of the designs were also printed in Ti6Al4V using direct metal laser sintering; however, these were not of sufficient quality to test further. Both the original metal screws (metal) and polymeric rapid prototyping screws were then tested using standard pull-out tests from low-density polyurethane blocks (Sawbones). Results showed the highest pull-out strengths for screws with the longest thread length and the smallest inner diameter. Of the six screw designs tested, five showed no more than a 17% variance between the metal and rapid prototyping results. A similar pattern of results was shown between the screw designs for both the metal and rapid prototyping screws in five of the six cases. While not producing fully comparable pull-out results to orthopaedic screws, the results from this study do provide evidence of the potential usefulness and cost-effectiveness of rapid prototyping in the early stages of design and testing of orthopaedic screws.

A comparative study of nerve stimulator versus ultrasound-guided supraclavicular brachial plexus block.

PubMed

Duncan, Mithun; Shetti, Akshaya N; Tripathy, Debendra Kumar; Roshansingh, D; Krishnaveni, N

2013-01-01

With the advent of ultrasound (US) guidance, this technique saw resurgence in the late 1990s. As US guidance provides real-time view of the block needle, the brachial plexus, and its spatial relationship to the surrounding vital structures; it not only increased the success rates, but also brought down the complication rates. Most of the studies show use of US guidance for performing brachial plexus block, results in near 100% success with or without complications. This study has been designed to examine the technique and usefulness of state-of-the-art US technology-guided supraclavicular brachial plexus block and compare it with routine nerve stimulator (NS)-guided technique. To note block execution time, time of onset of sensory and motor block, quality of block and success rates. Randomized controlled trial. A total of 60 patients were enrolled in this prospective randomized study and were randomly divided into two groups: US (Group US) and NS (Group NS). Both groups received 1:1 mixture of 0.5% bupivacaine and 2% lignocaine with 1:200000 adrenaline. The amount of local anaesthetic injected calculated according to the body weight and not crossing the toxic dosage (Inj. bupivacaine 2 mg/kg, Inj. lignocaine with adrenaline 7 mg/kg). The parameters compared between the two groups are block execution time, time of onset of sensory and motor block, quality of sensory and motor block, success rates are noted. The failed blocks are supplemented with general anesthesia. The data were analyzed using the SPSS (version 19) software. The parametric data were analyzed with student "t" test and the nonparametric data were analyzed with Chi-square test A P < 0.05 was considered significant. There was no significant difference between patient groups with regard to demographic data, the time of onset of sensory and motor block. Comparing the two groups, we found that the difference in the block execution time and success rates is not statistically significant. A failure rate of 10% in US and 20% in NS group observed and is statistically insignificant (P = 0.278). No complication observed in either group. US and NS group guidance for performing supraclavicular brachial plexus blocks ensures a high success rate and a decreased incidence of complications that are associated with the blind technique. However, our study did not prove the superiority of one technique over the other. The US-guided technique seemed to have an edge over the NS-guided technique. A larger study may be required to analyze the advantages of using US in performing supraclavicular brachial plexus blocks, which could help justify the cost of purchase of the US machine.

Experimental Design for a Sponge-Wipe Study to Relate the Recovery Efficiency and False Negative Rate to the Concentration of a Bacillus anthracis Surrogate for Six Surface Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piepel, Gregory F.; Amidan, Brett G.; Krauter, Paula

2011-05-01

Two concerns were raised by the Government Accountability Office following the 2001 building contaminations via letters containing Bacillus anthracis (BA). These included the: 1) lack of validated sampling methods, and 2) need to use statistical sampling to quantify the confidence of no contamination when all samples have negative results. Critical to addressing these concerns is quantifying the false negative rate (FNR). The FNR may depend on the 1) method of contaminant deposition, 2) surface concentration of the contaminant, 3) surface material being sampled, 4) sample collection method, 5) sample storage/transportation conditions, 6) sample processing method, and 7) sample analytical method.more » A review of the literature found 17 laboratory studies that focused on swab, wipe, or vacuum samples collected from a variety of surface materials contaminated by BA or a surrogate, and used culture methods to determine the surface contaminant concentration. These studies quantified performance of the sampling and analysis methods in terms of recovery efficiency (RE) and not FNR (which left a major gap in available information). Quantifying the FNR under a variety of conditions is a key aspect of validating sample and analysis methods, and also for calculating the confidence in characterization or clearance decisions based on a statistical sampling plan. A laboratory study was planned to partially fill the gap in FNR results. This report documents the experimental design developed by Pacific Northwest National Laboratory and Sandia National Laboratories (SNL) for a sponge-wipe method. The testing was performed by SNL and is now completed. The study investigated the effects on key response variables from six surface materials contaminated with eight surface concentrations of a BA surrogate (Bacillus atrophaeus). The key response variables include measures of the contamination on test coupons of surface materials tested, contamination recovered from coupons by sponge-wipe samples, RE, and FNR. The experimental design involves 16 test runs, performed in two blocks of eight runs. Three surface materials (stainless steel, vinyl tile, and ceramic tile) were tested in the first block, while three other surface materials (plastic, painted wood paneling, and faux leather) were tested in the second block. The eight surface concentrations of the surrogate were randomly assigned to test runs within each block. Some of the concentrations were very low and presented challenges for deposition, sampling, and analysis. However, such tests are needed to investigate RE and FNR over the full range of concentrations of interest. In each run, there were 10 test coupons of each of the three surface materials. A positive control sample was generated at the same time as each test sample. The positive control results will be used to 1) calculate RE values for the wipe sampling and analysis method, and 2) fit RE- and FNR-concentration equations, for each of the six surface materials. Data analyses will support 1) estimating the FNR for each combination of contaminant concentration and surface material, 2) estimating the surface concentrations and their uncertainties of the contaminant for each combination of concentration and surface material, 3) estimating RE (%) and their uncertainties for each combination of contaminant concentration and surface material, 4) fitting FNR-concentration and RE-concentration equations for each of the six surface materials, 5) assessing goodness-of-fit of the equations, and 6) quantifying the uncertainty in FNR and RE predictions made with the fitted equations.« less

6DOF Testing of the SLS Inertial Navigation Unit

NASA Technical Reports Server (NTRS)

Geohagan, Kevin; Bernard, Bill; Oliver, T. Emerson; Leggett, Jared; Strickland, Dennis

2018-01-01

The Navigation System on the NASA Space Launch System (SLS) Block 1 vehicle performs initial alignment of the Inertial Navigation System (INS) navigation frame through gyrocompass alignment (GCA). Because the navigation architecture for the SLS Block 1 vehicle is a purely inertial system, the accuracy of the achieved orbit relative to mission requirements is very sensitive to initial alignment accuracy. The assessment of this sensitivity and many others via simulation is a part of the SLS Model-Based Design and Model-Based Requirements approach. As a part of the aforementioned, 6DOF Monte Carlo simulation is used in large part to develop and demonstrate verification of program requirements. To facilitate this and the GN&C flight software design process, an SLS-Program-controlled Design Math Model (DMM) of the SLS INS was developed by the SLS Navigation Team. The SLS INS model implements all of the key functions of the hardware-namely, GCA, inertial navigation, and FDIR (Fault Detection, Isolation, and Recovery)-in support of SLS GN&C design requirements verification. Despite the strong sensitivity to initial alignment, GCA accuracy requirements were not verified by test due to program cost and schedule constraints. Instead, the system relies upon assessments performed using the SLS INS model. In order to verify SLS program requirements by analysis, the SLS INS model is verified and validated against flight hardware. In lieu of direct testing of GCA accuracy in support of requirement verification, the SLS Navigation Team proposed and conducted an engineering test to, among other things, validate the GCA performance and overall behavior of the SLS INS model through comparison with test data. This paper will detail dynamic hardware testing of the SLS INS, conducted by the SLS Navigation Team at Marshall Space Flight Center's 6DOF Table Facility, in support of GCA performance characterization and INS model validation. A 6-DOF motion platform was used to produce 6DOF pad twist and sway dynamics while a simulated SLS flight computer communicated with the INS. Tests conducted include an evaluation of GCA algorithm robustness to increasingly dynamic pad environments, an examination of GCA algorithm stability and accuracy over long durations, and a long-duration static test to gather enough data for Allan Variance analysis. Test setup, execution, and data analysis will be discussed, including analysis performed in support of SLS INS model validation.

Neuroimaging of decoding and language comprehension in young very low birth weight (VLBW) adolescents: Indications for compensatory mechanisms.

PubMed

van Ettinger-Veenstra, Helene; Widén, Carin; Engström, Maria; Karlsson, Thomas; Leijon, Ingemar; Nelson, Nina

2017-01-01

In preterm children with very low birth weight (VLBW ≤ 1500 g), reading problems are often observed. Reading comprehension is dependent on word decoding and language comprehension. We investigated neural activation-within brain regions important for reading-related to components of reading comprehension in young VLBW adolescents in direct comparison to normal birth weight (NBW) term-born peers, with the use of functional magnetic resonance imaging (fMRI). We hypothesized that the decoding mechanisms will be affected by VLBW, and expect to see increased neural activity for VLBW which may be modulated by task performance and cognitive ability. The study investigated 13 (11 included in fMRI) young adolescents (ages 12 to 14 years) born preterm with VLBW and in 13 NBW controls (ages 12-14 years) for performance on the Block Design and Vocabulary subtests of the Wechsler Intelligence Scale for Children; and for semantic, orthographic, and phonological processing during an fMRI paradigm. The VLBW group showed increased phonological activation in left inferior frontal gyrus, decreased orthographic activation in right supramarginal gyrus, and decreased semantic activation in left inferior frontal gyrus. Block Design was related to altered right-hemispheric activation, and VLBW showed lower WISC Block Design scores. Left angular gyrus showed activation increase specific for VLBW with high accuracy on the semantic test. Young VLBW adolescents showed no accuracy and reaction time performance differences on our fMRI language tasks, but they did exhibit altered neural activation during these tasks. This altered activation for VLBW was observed as increased activation during phonological decoding, and as mainly decreased activation during orthographic and semantic processing. Correlations of neural activation with accuracy on the semantic fMRI task and with decreased WISC Block Design performance were specific for the VLBW group. Together, results suggest compensatory mechanisms by recruiting additional brain regions upon altered neural development of decoding for VLBW.

The System Design, Engineering Architecture, and Preliminary Results of a Lower-Cost High-Sensitivity High-Resolution Positron Emission Mammography Camera.

PubMed

Zhang, Yuxuan; Ramirez, Rocio A; Li, Hongdi; Liu, Shitao; An, Shaohui; Wang, Chao; Baghaei, Hossain; Wong, Wai-Hoi

2010-02-01

A lower-cost high-sensitivity high-resolution positron emission mammography (PEM) camera is developed. It consists of two detector modules with the planar detector bank of 20 × 12 cm(2). Each bank has 60 low-cost PMT-Quadrant-Sharing (PQS) LYSO blocks arranged in a 10 × 6 array with two types of geometries. One is the symmetric 19.36 × 19.36 mm(2) block made of 1.5 × 1.5 × 10 mm(3) crystals in a 12 × 12 array. The other is the 19.36 × 26.05 mm(2) asymmetric block made of 1.5 × 1.9 × 10 mm(3) crystals in 12 × 13 array. One row (10) of the elongated blocks are used along one side of the bank to reclaim the half empty PMT photocathode in the regular PQS design to reduce the dead area at the edge of the module. The bank has a high overall crystal packing fraction of 88%, which results in a very high sensitivity. Mechanical design and electronics have been developed for low-cost, compactness, and stability purposes. Each module has four Anger-HYPER decoding electronics that can handle a count-rate of 3 Mcps for single events. A simple two-module coincidence board with a hardware delay window for random coincidences has been developed with an adjustable window of 6 to 15 ns. Some of the performance parameters have been studied by preliminary tests and Monte Carlo simulations, including the crystal decoding map and the 17% energy resolution of the detectors, the point source sensitivity of 11.5% with 50 mm bank-to-bank distance, the 1.2 mm-spatial resolutions, 42 kcps peak Noise Equivalent Count Rate at 7.0-mCi total activity in human body, and the resolution phantom images. Those results show that the design goal of building a lower-cost, high-sensitivity, high-resolution PEM detector is achieved.

Photovoltaic module reliability improvement through application testing and failure analysis

NASA Technical Reports Server (NTRS)

Dumas, L. N.; Shumka, A.

1982-01-01

During the first four years of the U.S. Department of Energy (DOE) National Photovoltatic Program, the Jet Propulsion Laboratory Low-Cost Solar Array (LSA) Project purchased about 400 kW of photovoltaic modules for test and experiments. In order to identify, report, and analyze test and operational problems with the Block Procurement modules, a problem/failure reporting and analysis system was implemented by the LSA Project with the main purpose of providing manufacturers with feedback from test and field experience needed for the improvement of product performance and reliability. A description of the more significant types of failures is presented, taking into account interconnects, cracked cells, dielectric breakdown, delamination, and corrosion. Current design practices and reliability evaluations are also discussed. The conducted evaluation indicates that current module designs incorporate damage-resistant and fault-tolerant features which address field failure mechanisms observed to date.

Space Shuttle Main Engine Low Pressure Oxidizer Turbo-Pump Inducer Dynamic Environment Characterization through Water Model and Hot-Fire Testing

NASA Technical Reports Server (NTRS)

Arellano, Patrick; Patton, Marc; Schwartz, Alan; Stanton, David

2006-01-01

The Low Pressure Oxidizer Turbopump (LPOTP) inducer on the Block II configuration Space Shuttle Main Engine (SSME) experienced blade leading edge ripples during hot firing. This undesirable condition led to a minor redesign of the inducer blades. This resulted in the need to evaluate the performance and the dynamic environment of the redesign, relative to the current configuration, as part of the design acceptance process. Sub-scale water model tests of the two inducer configurations were performed, with emphasis on the dynamic environment due to cavitation induced vibrations. Water model tests were performed over a wide range of inlet flow coefficient and pressure conditions, representative of the scaled operating envelope of the Block II SSME, both in flight and in ground hot-fire tests, including all power levels. The water test hardware, facility set-up, type and placement of instrumentation, the scope of the test program, specific test objectives, data evaluation process and water test results that characterize and compare the two SSME LPOTP inducers are discussed. In addition, dynamic characteristics of the two water models were compared to hot fire data from specially instrumented ground tests. In general, good agreement between the water model and hot fire data was found, which confirms the value of water model testing for dynamic characterization of rocket engine turbomachinery.

Multi-scale analysis of the effect of nano-filler particle diameter on the physical properties of CAD/CAM composite resin blocks.

PubMed

Yamaguchi, Satoshi; Inoue, Sayuri; Sakai, Takahiko; Abe, Tomohiro; Kitagawa, Haruaki; Imazato, Satoshi

2017-05-01

The objective of this study was to assess the effect of silica nano-filler particle diameters in a computer-aided design/manufacturing (CAD/CAM) composite resin (CR) block on physical properties at the multi-scale in silico. CAD/CAM CR blocks were modeled, consisting of silica nano-filler particles (20, 40, 60, 80, and 100 nm) and matrix (Bis-GMA/TEGDMA), with filler volume contents of 55.161%. Calculation of Young's moduli and Poisson's ratios for the block at macro-scale were analyzed by homogenization. Macro-scale CAD/CAM CR blocks (3 × 3 × 3 mm) were modeled and compressive strengths were defined when the fracture loads exceeded 6075 N. MPS values of the nano-scale models were compared by localization analysis. As the filler size decreased, Young's moduli and compressive strength increased, while Poisson's ratios and MPS decreased. All parameters were significantly correlated with the diameters of the filler particles (Pearson's correlation test, r = -0.949, 0.943, -0.951, 0.976, p < 0.05). The in silico multi-scale model established in this study demonstrates that the Young's moduli, Poisson's ratios, and compressive strengths of CAD/CAM CR blocks can be enhanced by loading silica nanofiller particles of smaller diameter. CAD/CAM CR blocks by using smaller silica nano-filler particles have a potential to increase fracture resistance.

A METHOD FOR USING BLOCKED AND EVENT-RELATED FMRI DATA TO STUDY “RESTING STATE” FUNCTIONAL CONNECTIVITY

PubMed Central

Fair, Damien A.; Schlaggar, Bradley L.; Cohen B.A., Alexander L.; Miezin, Francis M.; Dosenbach, Nico U.F.; Wenger, Kristin K.; Fox, Michael D.; Snyder, Abraham Z.; Raichle, Marcus E.; Petersen, Steven E.

2007-01-01

Resting state functional connectivity MRI (fcMRI) has become a particularly useful tool for studying regional relationships in typical and atypical populations. Because many investigators have already obtained large datasets of task related fMRI, the ability to use this existing task data for resting state fcMRI is of considerable interest. Two classes of datasets could potentially be modified to emulate resting state data. These datasets include: 1) “interleaved” resting blocks from blocked or mixed blocked/event-related sets, and 2) residual timecourses from event-related sets that lack rest blocks. Using correlation analysis, we compared the functional connectivity of resting epochs taken from a mixed blocked/event-related design fMRI data set and the residuals derived from event-related data with standard continuous resting state data to determine which class of data can best emulate resting state data. We show that despite some differences, the functional connectivity for the interleaved resting periods taken from blocked designs is both qualitatively and quantitatively very similar to that of “continuous” resting state data. In contrast, despite being qualitatively similar to “continuous” resting state data, residuals derived from event-related design data had several distinct quantitative differences. These results suggest that the interleaved resting state data such as those taken from blocked or mixed blocked/event-related fMRI designs are well-suited for resting state functional connectivity analyses. Although using event-related data residuals for resting state functional connectivity may still be useful, results should be interpreted with care. PMID:17239622

ETF magnet design alternatives for the national MHD program

NASA Astrophysics Data System (ADS)

Marston, P. G.; Thome, R. J.; Dawson, A. M.; Bobrov, E. S.; Hatch, A. M.

1981-01-01

Five superconducting magnet designs are evaluated for a 200 MWe test facility requiring a magnet with an on-axis field of 6 T, an inlet bore area of 4 sq m, storing 6 x 10 to the 9th J. The designs include a straightforward rectangular saddle coil set, a 'Cask' configuration based on staves and corner blocks as the main support structure, and an internally cooled, cabled superconductor to minimize the substructure and eliminate the helium vessel. Also, a modular design using six coils with individual helium vessels and an integrated structure produces a simplest configuration which utilizes a natural rectangular interface for packaging the MHD channel and its connections, and results in a lower capital cost.

Using CAD/CAM to improve productivity - The IPAD approach

NASA Technical Reports Server (NTRS)

Fulton, R. E.

1981-01-01

Progress in designing and implementing CAD/CAM systems as a result of the NASA Integrated Programs for Aerospace-Vehicle Design is discussed. Essential software packages have been identified as executive, data management, general user, and geometry and graphics software. Data communication, as a means to integrate data over a network of computers of different vendors, provides data management with the capability of meeting design and manufacturing requirements of the vendors. Geometry software is dependent on developmental success with solid geometry software, which is necessary for continual measurements of, for example, a block of metal while it is being machined. Applications in the aerospace industry, such as for design, analysis, tooling, testing, quality control, etc., are outlined.

Vowel perception by noise masked normal-hearing young adults

NASA Astrophysics Data System (ADS)

Richie, Carolyn; Kewley-Port, Diane; Coughlin, Maureen

2005-08-01

This study examined vowel perception by young normal-hearing (YNH) adults, in various listening conditions designed to simulate mild-to-moderate sloping sensorineural hearing loss. YNH listeners were individually age- and gender-matched to young hearing-impaired (YHI) listeners tested in a previous study [Richie et al., J. Acoust. Soc. Am. 114, 2923-2933 (2003)]. YNH listeners were tested in three conditions designed to create equal audibility with the YHI listeners; a low signal level with and without a simulated hearing loss, and a high signal level with a simulated hearing loss. Listeners discriminated changes in synthetic vowel tokens /smcapi e ɛ invv æ/ when F1 or F2 varied in frequency. Comparison of YNH with YHI results failed to reveal significant differences between groups in terms of performance on vowel discrimination, in conditions of similar audibility by using both noise masking to elevate the hearing thresholds of the YNH and applying frequency-specific gain to the YHI listeners. Further, analysis of learning curves suggests that while the YHI listeners completed an average of 46% more test blocks than YNH listeners, the YHI achieved a level of discrimination similar to that of the YNH within the same number of blocks. Apparently, when age and gender are closely matched between young hearing-impaired and normal-hearing adults, performance on vowel tasks may be explained by audibility alone.

Technological development of spectral filters for Sentinel-2

NASA Astrophysics Data System (ADS)

Schröter, Karin; Schallenberg, Uwe; Mohaupt, Matthias

2017-11-01

In the frame of the initiative for Global Monitoring for Environment and Security (GMES), jointly undertaken by the European Commission and the European Space Agency a technological development of two filter assemblies was performed for the Multi- Spectral Instrument (MSI) for Sentinel-2. The multispectral pushbroom imaging of the Earth will be performed in 10 VNIR bands (from 443 nm to 945nm) and 3 SWIR bands (from 1375 nm to 2190 nm). Possible filter coating techniques and masking concepts were considered in the frame of trade-off studies. The selected deposition concept is based on self-blocked all-dielectric multilayer band pass filter. Band pass and blocking characteristic is deposited on the space side of a single filter substrate whereas the detector side of the substrate has an antireflective coating. The space- and detector side masking design is realized by blades integrated in the mechanical parts including the mechanical interface to the filter assembly support on the MSI focal plane. The feasibility and required performance of the VNIR Filter Assembly and SWIR Filter Assembly were successfully demonstrated by breadboarding. Extensive performance tests of spectral and optical parameters and environmental tests (radiation, vibration, shock, thermal vacuum cycling, humidity) were performed on filter stripe- and filter assembly level. The presentation will contain a detailed description of the filter assembly design and the results of the performance and environmental tests.

Neuropsychological test performance and prediction of functional capacities among Spanish-speaking and English-speaking patients with dementia.

PubMed

Loewenstein, D A; Rubert, M P; Argüelles, T; Duara, R

1995-03-01

Neuropsychological measures have been widely used by clinicians to assist them in making judgments regarding a cognitively impaired patient's ability to independently perform important activities of daily living. However, important questions have been raised concerning the degree to which neuropsychological instruments can predict a broad array of specific functional capacities required in the home environment. In the present study, we examined 127 English-speaking and 56 Spanish-speaking patients with Alzheimer's disease (AD) and determined the extent to which various neuropsychological measures and demographic variables were predictive of performance on functional measures administered within the clinical setting. Among English-speaking AD patients, Block Design and Digit-Span of the WAIS-R, as well as tests of language were among the strongest predictors of functional performance. For Spanish-speakers, Block Design, The Mini-Mental State Evaluation (MMSE) and Digit Span had the optimal predictive power. When stepwise regression was conducted on the entire sample of 183 subjects, ethnicity emerged as a statistically significant predictor variable on one of the seven functional tests (writing a check). Despite the predictive power of several of the neuropsychological measures for both groups, most of the variability in objective functional performance could not be explained in our regression models. As a result, it would appear prudent to include functional measures as part of a comprehensive neuropsychological evaluation for dementia.

Effects of Tai Chi on Cognition and Fall Risk in Older Adults with Mild Cognitive Impairment: A Randomized Controlled Trial.

PubMed

Sungkarat, Somporn; Boripuntakul, Sirinun; Chattipakorn, Nipon; Watcharasaksilp, Kanokwan; Lord, Stephen R

2017-04-01

To examine whether combined center- and home-based Tai Chi training can improve cognitive ability and reduce physiological fall risk in older adults with amnestic mild cognitive impairment (a-MCI). Randomized controlled trial. Chiang Mai, Thailand. Adults aged 60 and older who met Petersen's criteria for multiple-domain a-MCI (N = 66). Three weeks center-based and 12 weeks home-based Tai Chi (50 minutes per session, 3 times per week). Cognitive tests, including Logical Memory (LM) delayed recall, Block Design, Digit Span forward and backward, and Trail-Making Test Part B-A (TMT B-A), and fall risk index using the Physiological Profile Assessment (PPA). At the end of the trial, performance on LM, Block Design, and TMT B-A were significantly better for the Tai Chi group than the control group after adjusting for baseline test performance. The Tai Chi group also had significantly better composite PPA score and PPA parameter scores: knee extension strength, reaction time, postural sway, and lower limb proprioception. Combined center- and home-based Tai Chi training three times per week for 15 weeks significantly improved cognitive function and moderately reduced physiological fall risk in older adults with multiple-domain a-MCI. Tai Chi may be particularly beneficial to older adults with this condition. © 2016, Copyright the Authors Journal compilation © 2016, The American Geriatrics Society.

Application of dimensional analysis to predict the performance of rockfall barrier

NASA Astrophysics Data System (ADS)

Spadari, M.; Giacomini, A.; Buzzi, O.; Hambleton, J.

2012-04-01

Natural hazards involving rocks or rock slopes are responsible for loss of life and damage to infrastructure and are consequently widely studied. Rock fall barriers are a common type of protection structures that is usually designed on the basis of total impact energy. However, the systems are usually tested in free fall where the predominant component of energy is kinematic and it has been shown that there is not a unique relationship between the response of a barrier and the kinetic energy of the impacting block. In particular, recent studies have discussed the so called "bullet effect" i.e. relatively small blocks traveling at high speed can perforate the barriers yet having acceptable level of energy. This effect compromises the use of kinetic energy as an adequate design criterion since there is not a threshold value defining clearly acceptable and unacceptable values of energy. This issue can be addressed empirically by using different block sizes when it comes to test a system. However, the literature still lacks a characterization of a rockfall barrier performance regarding the bullet effect. This note presents the results of the application of dimensional analysis to the physical problem of the bullet effect. This latter has been formulated as a function involving eight key variables: v = f(ρ, K, σy, H, A, Db,Dw) where v is the minimum speed of a given block to break the barrier, ρgs the density of the block, Kis the stiffness of the system, σy is the strength of the wires, H is the height of the barrier, A is the aperture of the mesh, Db is the dimension of the block and Dw is the diameter of the wire. Applying the Buckingham Pi theorem allows reducing the equation above to a simpler problem involving only three dimensionless parameters: E*=F(S*, G*) Where E* is the performance parameter, S* is the strength-stiffness parameter and G* is the geometrical parameters defined as: E*= (ρ.v2.H)/K S*=K/(H.gσy) And G*=A-0.25.Db-0.75.Db F in the simplified equation is referred to as the Rockfall Barrier Performance, or RoBaP, Model. Results suggest that the dimensional analysis can satisfactorily be used to assess the performance of a barrier when impacted by variable block size. A calibration-prediction exercise has been conducted using data form the literature to assess the predictive capability of the RoBaP model. It has been found that the RoBaP model gives satisfactory results. In particular, the progressive loss of performance of the rock fall barrier as the block size diminishes has been well captured.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Phase I program and the design plan for the Phase II Experiment Integration wherein the AAI Corporation's 24/1 concentrating collector is used to produce hot water to cure concrete blocks is described. This concept has a tremendous potential since each block requires about 1500 Btu for curing at a temperature of 140/sup 0/F to 180/sup 0/F. To demonstrate this process, the solar hot water system will be installed at the new block fabricating plant being built by the York Building Products Co., Inc. at Harrisburg, Pa. A circular underground curing tank will be the storage tank for the solarmore » system. Since the plane is new, no retrofitting is required. The collectors will be mounted on the roof of the new block producing facility. A full-scale 256 ft/sup 2/ module of the 24/1 collector has been built and tested by AAI Corporation. A 9216 ft/sup 2/ array of collectors is required for this experiment. AAI Corporation is pursuing a development program planned to culminate in the marketing of the 24/1 collector at a selling price of $7 to $10 per square foot. The collector is built in 9 ft by 34 ft modules and is self-supporting with pads located at the four corners. It can be inclined at the most favorable angle for solar performance, and can be located on a roof, or as a separate unit on the ground. A final design and performance analysis and an economic analysis are presented. (WHK)« less

Block recursive LU preconditioners for the thermally coupled incompressible inductionless MHD problem

NASA Astrophysics Data System (ADS)

Badia, Santiago; Martín, Alberto F.; Planas, Ramon

2014-10-01

The thermally coupled incompressible inductionless magnetohydrodynamics (MHD) problem models the flow of an electrically charged fluid under the influence of an external electromagnetic field with thermal coupling. This system of partial differential equations is strongly coupled and highly nonlinear for real cases of interest. Therefore, fully implicit time integration schemes are very desirable in order to capture the different physical scales of the problem at hand. However, solving the multiphysics linear systems of equations resulting from such algorithms is a very challenging task which requires efficient and scalable preconditioners. In this work, a new family of recursive block LU preconditioners is designed and tested for solving the thermally coupled inductionless MHD equations. These preconditioners are obtained after splitting the fully coupled matrix into one-physics problems for every variable (velocity, pressure, current density, electric potential and temperature) that can be optimally solved, e.g., using preconditioned domain decomposition algorithms. The main idea is to arrange the original matrix into an (arbitrary) 2 × 2 block matrix, and consider an LU preconditioner obtained by approximating the corresponding Schur complement. For every one of the diagonal blocks in the LU preconditioner, if it involves more than one type of unknowns, we proceed the same way in a recursive fashion. This approach is stated in an abstract way, and can be straightforwardly applied to other multiphysics problems. Further, we precisely explain a flexible and general software design for the code implementation of this type of preconditioners.

Matching Speaking to Singing Voices and the Influence of Content.

PubMed

Peynircioğlu, Zehra F; Rabinovitz, Brian E; Repice, Juliana

2017-03-01

We tested whether speaking voices of unfamiliar people could be matched to their singing voices, and, if so, whether the content of the utterances would influence this matching performance. Our hypothesis was that enough acoustic features would remain the same between speaking and singing voices such that their identification as belonging to the same or different individuals would be possible even upon a single hearing. We also hypothesized that the contents of the utterances would influence this identification process such that voices uttering words would be easier to match than those uttering vowels. We used a within-participant design with blocked stimuli that were counterbalanced using a Latin square design. In one block, mode (speaking vs singing) was manipulated while content was held constant; in another block, content (word vs syllable) was manipulated while mode was held constant, and in the control block, both mode and content were held constant. Participants indicated whether the voices in any given pair of utterances belonged to the same person or to different people. Cross-mode matching was above chance level, although mode-congruent performance was better. Further, only speaking voices were easier to match when uttering words. We can identify speaking and singing voices as the same or different even on just a single hearing. However, content interacts with mode such that words benefit matching of speaking voices but not of singing voices. Results are discussed within an attentional framework. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Laboratory Characterization of Cemented Rock Fill for Underhand Cut and Fill Method of Mining

NASA Astrophysics Data System (ADS)

Kumar, Dinesh; Singh, Upendra Kumar; Singh, Gauri Shankar Prasad

2016-10-01

Backfilling with controlled specifications is employed for improved ground support and pillar recovery in underground metalliferous mine workings. This paper reports the results of a laboratory study to characterise various mechanical properties of cemented rock fill (CRF) formulations for different compaction levels and cement content percentage for use in underhand cut and fill method of mining. Laboratory test set ups and procedures have been described for conducting compressive and bending tests of CRF block samples. A three dimensional numerical modelling study has also been carried out to overcome the limitations arising due to non-standard dimension of test blocks used in flexural loading test and the test setup devised for this purpose. Based on these studies, specific relations have been established between the compressive and the flexural properties of the CRF. The flexural strength of the wire mesh reinforced CRF is also correlated with its residual strength and the Young's modulus of elasticity under flexural loading condition. The test results of flexural strength, residual flexural strength and modulus show almost linear relations with cement content in CRF. The compressive strength of the CRF block samples is estimated as seven times the flexural strength whereas the compressive modulus is four times the flexural modulus. It has been found that the strengths of CRF of low compaction and no compaction are 75 and 60 % respectively to that of the medium compaction CRF. The relation between the strength and the unit weight of CRF as obtained in this study is significantly important for design and quality control of CRF during its large scale application in underhand cut and fill stopes.

Application of welding simulation to block joints in shipbuilding and assessment of welding-induced residual stresses and distortions

NASA Astrophysics Data System (ADS)

Fricke, Wolfgang; Zacke, Sonja

2014-06-01

During ship design, welding-induced distortions are roughly estimated as a function of the size of the component as well as the welding process and residual stresses are assumed to be locally in the range of the yield stress. Existing welding simulation methods are very complex and time-consuming and therefore not applicable to large structures like ships. Simplified methods for the estimation of welding effects were and still are subject of several research projects, but mostly concerning smaller structures. The main goal of this paper is the application of a multi-layer welding simulation to the block joint of a ship structure. When welding block joints, high constraints occur due to the ship structure which are assumed to result in accordingly high residual stresses. Constraints measured during construction were realized in a test plant for small-scale welding specimens in order to investigate their and other effects on the residual stresses. Associated welding simulations were successfully performed with fine-mesh finite element models. Further analyses showed that a courser mesh was also able to reproduce the welding-induced reaction forces and hence the residual stresses after some calibration. Based on the coarse modeling it was possible to perform the welding simulation at a block joint in order to investigate the influence of the resulting residual stresses on the behavior of the real structure, showing quite interesting stress distributions. Finally it is discussed whether smaller and idealized models of definite areas of the block joint can be used to achieve the same results offering possibilities to consider residual stresses in the design process.

Environmental and Water Quality Operational Studies. Environmental Guidelines for Dike Fields.

DTIC Science & Technology

1984-09-01

public release; distribution unlimited. I. DISTRIBUTION STATEMENT (of the abstract entered In Block 20, If different from Report) IS. SUPPLEMENTARY NOTES...necessary and identify by block number) Aquatic biology--Environmental aspects. (LC) Dikes (Engineering)--Design and construction--Environmental...w ad Idenwify by block number) ’The environmental guidelines for dike fields-contained within this report consist of environmental objectives, design

Spreading activation in nonverbal memory networks.

PubMed

Foster, Paul S; Wakefield, Candias; Pryjmak, Scott; Roosa, Katelyn M; Branch, Kaylei K; Drago, Valeria; Harrison, David W; Ruff, Ronald

2017-09-01

Theories of spreading activation primarily involve semantic memory networks. However, the existence of separate verbal and visuospatial memory networks suggests that spreading activation may also occur in visuospatial memory networks. The purpose of the present investigation was to explore this possibility. Specifically, this study sought to create and describe the design frequency corpus and to determine whether this measure of visuospatial spreading activation was related to right hemisphere functioning and spreading activation in verbal memory networks. We used word frequencies taken from the Controlled Oral Word Association Test and design frequencies taken from the Ruff Figural Fluency Test as measures of verbal and visuospatial spreading activation, respectively. Average word and design frequencies were then correlated with measures of left and right cerebral functioning. The results indicated that a significant relationship exists between performance on a test of right posterior functioning (Block Design) and design frequency. A significant negative relationship also exists between spreading activation in semantic memory networks and design frequency. Based on our findings, the hypotheses were supported. Further research will need to be conducted to examine whether spreading activation exists in visuospatial memory networks as well as the parameters that might modulate this spreading activation, such as the influence of neurotransmitters.

Vinblastine and diethylstilboestrol tested in the in vitro mammalian cell micronucleus test (MNvit) at Swansea University UK in support of OECD draft Test Guideline 487.

PubMed

Johnson, George E; Jenkins, Gareth J; Thomas, Adam D; Doak, Shareen H

2010-10-29

The known aneugens vinblastine and diethylstilboestrol (DES) were tested in the in vitro micronucleus assay, with and without cytokinesis block in Chinese hamster CHO cells, at the laboratories of Swansea University, Swansea, UK. These experiments were carried out to determine the suitability of the cell death and cytostasis measures used in the assay, as recommended in the draft OECD Test Guideline 487, 2007. Both compounds were positive in the assay without cytokinesis block at concentrations giving approximately 50% or less cell death and cytostasis, using relative population doublings and relative increase in cell counts. Moreover, both compounds were positive in the assay with cytokinesis block at concentrations giving approximately 50% cell death and cytostasis, using replicative index. Vinblastine was also positive for mitotic slippage, causing micronuclei in mononucleate cells with cytokinesis block. Relative population doublings and relative increase in cell counts were appropriate measures of cell death and cytostasis for the non-cytokinesis block in vitro micronucleus assay. In the cytokinesis blocked micronucleus assay, replicative index and cytokinesis block proliferation index were suitable cell death and cytostasis measures. Copyright © 2009 Elsevier B.V. All rights reserved.

Fault-tolerant computer study. [logic designs for building block circuits

NASA Technical Reports Server (NTRS)

Rennels, D. A.; Avizienis, A. A.; Ercegovac, M. D.

1981-01-01

A set of building block circuits is described which can be used with commercially available microprocessors and memories to implement fault tolerant distributed computer systems. Each building block circuit is intended for VLSI implementation as a single chip. Several building blocks and associated processor and memory chips form a self checking computer module with self contained input output and interfaces to redundant communications buses. Fault tolerance is achieved by connecting self checking computer modules into a redundant network in which backup buses and computer modules are provided to circumvent failures. The requirements and design methodology which led to the definition of the building block circuits are discussed.

Effects of three silane primers and five adhesive agents on the bond strength of composite material for a computer-aided design and manufacturing system.

PubMed

Shinohara, Ayano; Taira, Yohsuke; Sakihara, Michino; Sawase, Takashi

2018-01-01

Objective The objective of this study was to evaluate the effects of combinations of silane primers and adhesive agents on the bond strength of a composite block for a computer-aided design and manufacturing system. Material and Methods Three silane primers [Clearfil Ceramic Primer (CP), Super-Bond PZ Primer (PZ), and GC Ceramic Primer II (GP)] were used in conjunction with five adhesive agents [G-Premio Bond (P-Bond), Repair Adhe Adhesive (R-Adhesive), Super-Bond D-Liner Dual (SB-Dual), Super-Bond C&B (SB-Self), and SB-Dual without tributylborane derivative (SB-Light)]. The surface of a composite block (Gradia Block) was ground with silicon carbide paper. After treatment with a silane primer, a adhesive agent was applied to each testing specimen. The specimens were then bonded with a light-curing resin composite. After 24 h, the shear bond strength values were determined and compared using a post hoc test (α=0.05, n=8/group). We also prepared control specimens without primer (No primer) and/or without adhesive agent (No adhesive). Results PZ/SB-Dual and GP/SB-Dual presented the highest bond strength, followed by GP/P-Bond, CP/SB-Dual, CP/R-Adhesive, No primer/SB-Dual, GP/R-Adhesive, CP/P-Bond, No primer/R-Adhesive, PZ/R-Adhesive, CP/SB-Self, PZ/P-Bond, PZ/SB-Self, and GP/SB-Self in descending order of bond strength. No primer/P-Bond, No primer/SB-Self, and all specimens in the SB-Light and No adhesive groups presented the lowest bond strengths. Conclusion A dual-curing adhesive agent (SB-Dual) containing a tributylborane derivative in combination with a silane primer (GP or PZ) presents a greater bond strength between the composite block and the repairing resin composite than the comparators used in the study.

Effects of three silane primers and five adhesive agents on the bond strength of composite material for a computer-aided design and manufacturing system

PubMed Central

2018-01-01

Abstract Objective The objective of this study was to evaluate the effects of combinations of silane primers and adhesive agents on the bond strength of a composite block for a computer-aided design and manufacturing system. Material and Methods Three silane primers [Clearfil Ceramic Primer (CP), Super-Bond PZ Primer (PZ), and GC Ceramic Primer II (GP)] were used in conjunction with five adhesive agents [G-Premio Bond (P-Bond), Repair Adhe Adhesive (R-Adhesive), Super-Bond D-Liner Dual (SB-Dual), Super-Bond C&B (SB-Self), and SB-Dual without tributylborane derivative (SB-Light)]. The surface of a composite block (Gradia Block) was ground with silicon carbide paper. After treatment with a silane primer, a adhesive agent was applied to each testing specimen. The specimens were then bonded with a light-curing resin composite. After 24 h, the shear bond strength values were determined and compared using a post hoc test (α=0.05, n=8/group). We also prepared control specimens without primer (No primer) and/or without adhesive agent (No adhesive). Results PZ/SB-Dual and GP/SB-Dual presented the highest bond strength, followed by GP/P-Bond, CP/SB-Dual, CP/R-Adhesive, No primer/SB-Dual, GP/R-Adhesive, CP/P-Bond, No primer/R-Adhesive, PZ/R-Adhesive, CP/SB-Self, PZ/P-Bond, PZ/SB-Self, and GP/SB-Self in descending order of bond strength. No primer/P-Bond, No primer/SB-Self, and all specimens in the SB-Light and No adhesive groups presented the lowest bond strengths. Conclusion A dual-curing adhesive agent (SB-Dual) containing a tributylborane derivative in combination with a silane primer (GP or PZ) presents a greater bond strength between the composite block and the repairing resin composite than the comparators used in the study. PMID:29742254

Performance and Fabrication Status of TREAT LEU Conversion Conceptual Design Concepts

DOE Office of Scientific and Technical Information (OSTI.GOV)

IJ van Rooyen; SR Morrell; AE Wright

2014-10-01

Resumption of transient testing at the TREAT facility was approved in February 2014 to meet U.S. Department of Energy (DOE) objectives. The National Nuclear Security Administration’s Global Threat Reduction Initiative Convert Program is evaluating conversion of TREAT from its existing highly enriched uranium (HEU) core to a new core containing low enriched uranium (LEU). This paper describes briefly the initial pre-conceptual designs screening decisions with more detailed discussions on current feasibility, qualification and fabrication approaches. Feasible fabrication will be shown for a LEU fuel element assembly that can meet TREAT design, performance, and safety requirements. The statement of feasibility recognizesmore » that further development, analysis, and testing must be completed to refine the conceptual design. Engineering challenges such as cladding oxidation, high temperature material properties, and fuel block fabrication along with neutronics performance, will be highlighted. Preliminary engineering and supply chain evaluation provided confidence that the conceptual designs can be achieved.« less

Thermal/structural Tailoring of Engine Blades (T/SEAEBL). Theoretical Manual

NASA Technical Reports Server (NTRS)

Brown, K. W.; Clevenger, W. B.

1994-01-01

The Thermal/Structural Tailoring of Engine Blades (T/STAEBL) system is a family of computer programs executed by a control program. The T/STAEBL system performs design optimizations of cooled, hollow turbine blades and vanes. This manual describes the T/STAEBL data block structure and system organization. The approximate analysis and optimization modules are detailed, and a validation test case is provided.

Development of a Simulink Library for the Design, Testing and Simulation of Software Defined GPS Radios. With Application to the Development of Parallel Correlator Structures

DTIC Science & Technology

2014-05-01

function Value = Select_Element(Index,Signal) %# eml Value = Signal(Index); Code Listing 1 Code for Selector Block 12 | P a g e 4.3...code for the Simulink function shiftedSignal = fcn(signal,Shift) %# eml shiftedSignal = circshift(signal,Shift); Code Listing 2 Code for CircShift

A comparison of three erosion control mulches on decommissioned forest road corridors in the northern Rocky Mountains, United States

Treesearch

R. B. Foltz

2012-01-01

This study tested the erosion mitigation effectiveness of agricultural straw and two wood-based mulches for four years on decommissioned forest roads. Plots were installed on the loosely consolidated, bare soil to measure sediment production, mulch cover, and plant regrowth. The experimental design was a repeated measures, randomized block on two soil types common in...

Thermal/structural tailoring of engine blades (T/SEAEBL). Theoretical manual

NASA Astrophysics Data System (ADS)

Brown, K. W.; Clevenger, W. B.

1994-03-01

The Thermal/Structural Tailoring of Engine Blades (T/STAEBL) system is a family of computer programs executed by a control program. The T/STAEBL system performs design optimizations of cooled, hollow turbine blades and vanes. This manual describes the T/STAEBL data block structure and system organization. The approximate analysis and optimization modules are detailed, and a validation test case is provided.

Effect of fertilizer applications and grazing exclusion on species composition and biomass in wet meadow restoration in eastern Washington.

Treesearch

John Beebe; Richard Everett; George Scherer; Carl. Davis

2002-01-01

Fertilizer applications and grazing exclusion were used as restoration strategies in degraded wet meadows in eastern Washington to grow biomass in the root systems where it could not be grazed. We used a split-block design to test vegetation responses to six fertilizer rates, eight fertilizer types, and three grazing treatments after three growing seasons. Little...

The Role of Simplification and Information in College Decisions: Results from the H&R Block FAFSA Experiment. NBER Working Paper No. 15361

ERIC Educational Resources Information Center

Bettinger, Eric P.; Long, Bridget Terry; Oreopoulos, Philip; Sanbonmatsu, Lisa

2009-01-01

Growing concerns about low awareness and take-up rates for government support programs like college financial aid have spurred calls to simplify the application process and enhance visibility. This project examines the effects of two experimental treatments designed to test of the importance of simplification and information using a random…

A Novel Field-Deployable Point-of-Care Diagnostic Test for Cutaneous Leishmaniasis

DTIC Science & Technology

2016-10-01

and should not be construed as an official Department of the Army position, policy or decision unless so designated by other documentation. REPORT...PERFORMING ORGANIZATION REPORT NUMBER Venezuela Av. Block 36 Bellavista, Callao-Peru University of Texas Medical Branch,301 University Blvd, Marvin...practices, decision making, policies (including regulatory policies ), or social actions; or improving social, economic, civic, or environmental

Initial Mechanical Testing of Superalloy Lattice Block Structures Conducted

NASA Technical Reports Server (NTRS)

Krause, David L.; Whittenberger, J. Daniel

2002-01-01

The first mechanical tests of superalloy lattice block structures produced promising results for this exciting new lightweight material system. The testing was performed in-house at NASA Glenn Research Center's Structural Benchmark Test Facility, where small subelement-sized compression and beam specimens were loaded to observe elastic and plastic behavior, component strength levels, and fatigue resistance for hundreds of thousands of load cycles. Current lattice block construction produces a flat panel composed of thin ligaments arranged in a three-dimensional triangulated trusslike structure. Investment casting of lattice block panels has been developed and greatly expands opportunities for using this unique architecture in today's high-performance structures. In addition, advances made in NASA's Ultra-Efficient Engine Technology Program have extended the lattice block concept to superalloy materials. After a series of casting iterations, the nickel-based superalloy Inconel 718 (IN 718, Inco Alloys International, Inc., Huntington, WV) was successfully cast into lattice block panels; this combination offers light weight combined with high strength, high stiffness, and elevated-temperature durability. For tests to evaluate casting quality and configuration merit, small structural compression and bend test specimens were machined from the 5- by 12- by 0.5-in. panels. Linear elastic finite element analyses were completed for several specimen layouts to predict material stresses and deflections under proposed test conditions. The structural specimens were then subjected to room-temperature static and cyclic loads in Glenn's Life Prediction Branch's material test machine. Surprisingly, the test results exceeded analytical predictions: plastic strains greater than 5 percent were obtained, and fatigue lives did not depreciate relative to the base material. These assets were due to the formation of plastic hinges and the redundancies inherent in lattice block construction, which were not considered in the simplified computer models. The fatigue testing proved the value of redundancies since specimen strength was maintained even after the fracture of one or two ligaments. This ongoing test program is planned to continue through high-temperature testing. Also scheduled for testing are IN 718 lattice block panels with integral face sheets, as well as specimens cast from a higher temperature alloy. The initial testing suggests the value of this technology for large panels under low and moderate pressure loadings and for high-risk, damage-tolerant structures. Potential aeropropulsion uses for lattice blocks include turbine-engine actuated panels, exhaust nozzle flaps, and side panel structures.

Computational Design of Self-Assembling Protein Nanomaterials with Atomic Level Accuracy

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Neil P.; Sheffler, William; Sawaya, Michael R.

2015-09-17

We describe a general computational method for designing proteins that self-assemble to a desired symmetric architecture. Protein building blocks are docked together symmetrically to identify complementary packing arrangements, and low-energy protein-protein interfaces are then designed between the building blocks in order to drive self-assembly. We used trimeric protein building blocks to design a 24-subunit, 13-nm diameter complex with octahedral symmetry and a 12-subunit, 11-nm diameter complex with tetrahedral symmetry. The designed proteins assembled to the desired oligomeric states in solution, and the crystal structures of the complexes revealed that the resulting materials closely match the design models. The method canmore » be used to design a wide variety of self-assembling protein nanomaterials.« less

Effect of Video-Assisted Teaching Module (VATM) on Knowledge of ASHAs regarding RNTCP in Kuchinda Block of Sambalpur (Odisha).

PubMed

Pradhan, Malati; Dash, Bijayalakshmi

2015-05-01

Infectious disease is a major public health issue for both developed and developing countries. Among infectious diseases, tuberculosis (TB) is most prevalent in the develop- ing countries. India is the highest TB burden country in the world and accounts for nearly one fifth (20%) of global burden of tuberculosis. A pre-experimental design where pre- and post-test without control group with experimental approach was undertaken in Kuchinda block of Sambalpur district (Odisha) with the objectives to assess effectiveness of Video-assisted Teaching Module (VATM) on knowledge of Accredited Social Health Activists (ASHAs) regarding Revised National Tuberculosis Control Programme (RNTCP) Data were collected from 52 ASHAs, selected by systematic random sampling technique through structured questionnaire. The overall mean score in pre-test was 23.31±3.07 which is 58.27 percent of maximum score and good knowledge whereas it was 34.35±3.56 while post-test it was 85.87 percent of maximum score during post-test showing a difference of 27.6 percent effectiveness. Highly significant (p<0.01) differ- ence was found between pre- and post-test knowledge score and no significant (>0.05) association was found between post-test knowledge score when compared to all the demographic variables of ASHAs.

Experimental Design for a Sponge-Wipe Study to Relate the Recovery Efficiency and False Negative Rate to the Concentration of a Bacillus anthracis Surrogate for Six Surface Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piepel, Gregory F.; Amidan, Brett G.; Krauter, Paula

2010-12-16

Two concerns were raised by the Government Accountability Office following the 2001 building contaminations via letters containing Bacillus anthracis (BA). These included the: 1) lack of validated sampling methods, and 2) need to use statistical sampling to quantify the confidence of no contamination when all samples have negative results. Critical to addressing these concerns is quantifying the probability of correct detection (PCD) (or equivalently the false negative rate FNR = 1 - PCD). The PCD/FNR may depend on the 1) method of contaminant deposition, 2) surface concentration of the contaminant, 3) surface material being sampled, 4) sample collection method, 5)more » sample storage/transportation conditions, 6) sample processing method, and 7) sample analytical method. A review of the literature found 17 laboratory studies that focused on swab, wipe, or vacuum samples collected from a variety of surface materials contaminated by BA or a surrogate, and used culture methods to determine the surface contaminant concentration. These studies quantified performance of the sampling and analysis methods in terms of recovery efficiency (RE) and not PCD/FNR (which left a major gap in available information). Quantifying the PCD/FNR under a variety of conditions is a key aspect of validating sample and analysis methods, and also for calculating the confidence in characterization or clearance decisions based on a statistical sampling plan. A laboratory study was planned to partially fill the gap in PCD/FNR results. This report documents the experimental design developed by Pacific Northwest National Laboratory and Sandia National Laboratories (SNL) for a sponge-wipe method. The study will investigate the effects on key response variables from six surface materials contaminated with eight surface concentrations of a BA surrogate (Bacillus atrophaeus). The key response variables include measures of the contamination on test coupons of surface materials tested, contamination recovered from coupons by sponge-wipe samples, RE, and PCD/FNR. The experimental design involves 16 test runs, to be performed in two blocks of eight runs. Three surface materials (stainless steel, vinyl tile, and ceramic tile) were tested in the first block, while three other surface materials (plastic, painted wood paneling, and faux leather) will be tested in the second block. The eight surface concentrations of the surrogate were randomly assigned to test runs within each block. Some of the concentrations will be very low and may present challenges for deposition, sampling, and analysis. However, such tests are needed to investigate RE and PCD/FNR over the full range of concentrations of interest. In each run, there will be 10 test coupons of each of the three surface materials. A positive control sample will be generated prior to each test sample. The positive control results will be used to 1) calculate RE values for the wipe sampling and analysis method, and 2) fit RE- and PCD-concentration equations, for each of the six surface materials. Data analyses will support 1) estimating the PCD for each combination of contaminant concentration and surface material, 2) estimating the surface concentrations and their uncertainties of the contaminant for each combination of concentration and surface material, 3) estimating RE (%) and their uncertainties for each combination of contaminant concentration and surface material, 4) fitting PCD-concentration and RE-concentration equations for each of the six surface materials, 5) assessing goodness-of-fit of the equations, and 6) quantifying the uncertainty in PCD and RE predictions made with the fitted equations.« less

Sensing fluid pressure during plucking events in a natural bedrock channel and experimental flume

NASA Astrophysics Data System (ADS)

Wilkinson, C.; Harbor, D. J.; Keel, D.; Levy, S.; Kuehner, J. P.

2016-12-01

River channel erosion by plucking is believed to be the dominant erosional process in channels with fractured or jointed bedrock. However, despite its significance as an erosional mechanism, plucking is poorly studied in both laboratory and natural channels. In previous flume studies, model bedrock was plucked by fluid forces alone in nonuniform flow near jumps and waves even where blocks do not protrude into the flow. Here we develop sensor systems to test the hypothesis that bed fluid pressure gradients lift "pluckable" bedrock blocks in a natural field setting and a hydraulic flume. The field setting closely mimics the previous flume setup; the instrumented block is downstream of a roughly 1m step and exhibits no protrusion into the flow. The presence of the step promotes nonuniform flow which changes pressure in the bedrock crack network; slabs of bedrock that have slid downstream and sediment that has been pushed upstream 3-4 m under the bed and in the cracks suggest the influence of pressure differences throughout the crack network and below the bed. In this initial deployment, we evaluate a sensor that monitors movement and simultaneous pressure above and below the block. Sensors are emplaced in a 26kg, 45-cm-long, 20-cm-wide block broken from a 4.5-m-long, 11-cm-thick sandstone bed with a dense network of cracks nearly parallel to flow direction and include a tri-axial accelerometer/gyroscope and two fluid pressure sensors. The electronics are housed in a custom-designed 3D-printed ABS waterproof capsule that is mounted in a vertical hole through the rock. A concurrent flume study develops the sensors necessary to investigate the longitudinal pressure difference below a step using multiple analog sensors (0-1 psi gauge pressure) mounted flush to a false floor under the center of a 30x14-cm test zone. The 15-mm-wide sensors are aligned along the flow centerline and are placed under 25 1-cm-thick "pluckable" bedrock blocks constructed with a proprietary plaster cement. Measured mean pressure and transmission of pressure pulses under the test bed are compared to the visual record of plucking. In addition, conducting runs with blocks removed permits simulation of the mean and varying pressure conditions above the modeled "pluckable" layer as a hydraulic jump is moved downstream through the step.

Revisiting measurement invariance in intelligence testing in aging research: Evidence for almost complete metric invariance across age groups.

PubMed

Sprague, Briana N; Hyun, Jinshil; Molenaar, Peter C M

2017-01-01

Invariance of intelligence across age is often assumed but infrequently explicitly tested. Horn and McArdle (1992) tested measurement invariance of intelligence, providing adequate model fit but might not consider all relevant aspects such as sub-test differences. The goal of the current paper is to explore age-related invariance of the WAIS-R using an alternative model that allows direct tests of age on WAIS-R subtests. Cross-sectional data on 940 participants aged 16-75 from the WAIS-R normative values were used. Subtests examined were information, comprehension, similarities, vocabulary, picture completion, block design, picture arrangement, and object assembly. The two intelligence factors considered were fluid and crystallized intelligence. Self-reported ages were divided into young (16-22, n = 300), adult (29-39, n = 275), middle (40-60, n = 205), and older (61-75, n = 160) adult groups. Results suggested partial metric invariance holds. Although most of the subtests reflected fluid and crystalized intelligence similarly across different ages, invariance did not hold for block design on fluid intelligence and picture arrangement on crystallized intelligence for older adults. Additionally, there was evidence of a correlated residual between information and vocabulary for the young adults only. This partial metric invariance model yielded acceptable model fit compared to previously-proposed invariance models of Horn and McArdle (1992). Almost complete metric invariance holds for a two-factor model of intelligence. Most of the subtests were invariant across age groups, suggesting little evidence for age-related bias in the WAIS-R. However, we did find unique relationships between two subtests and intelligence. Future studies should examine age-related differences in subtests when testing measurement invariance in intelligence.

Receiver-exciter controller design

NASA Technical Reports Server (NTRS)

Jansma, P. A.

1982-01-01

A description of the general design of both the block 3 and block 4 receiver-exciter controllers for the Deep Space Network (DSN) Mark IV-A System is presented along with the design approach. The controllers are designed to enable the receiver-exciter subsystem (RCV) to be configured, calibrated, initialized and operated from a central location via high level instructions. The RECs are designed to be operated under the control of the DMC subsystem. The instructions are in the form of standard subsystem blocks (SSBs) received via the local area network (LAN). The centralized control provided by RECs and other DSCC controllers in Mark IV-A is intended to reduce DSN operations costs from the Mark III era.

Age-related differences in strategy knowledge updating: blocked testing produces greater improvements in metacognitive accuracy for younger than older adults.

PubMed

Price, Jodi; Hertzog, Christopher; Dunlosky, John

2008-09-01

Age-related differences in updating knowledge about strategy effectiveness after task experience have not been consistently found, perhaps because the magnitude of observed knowledge updating has been rather meager for both age groups. We examined whether creating homogeneous blocks of recall tests based on two strategies used at encoding (imagery and repetition) would enhance people's learning about strategy effects on recall. Younger and older adults demonstrated greater knowledge updating (as measured by questionnaire ratings of strategy effectiveness and by global judgments of performance) with blocked (versus random) testing. The benefit of blocked testing for absolute accuracy of global predictions was smaller for older than younger adults. However, individual differences in correlations of strategy effectiveness ratings and postdictions showed similar upgrades for both age groups. Older adults learn about imagery's superior effectiveness but do not accurately estimate the magnitude of its benefit, even after blocked testing.

UV-vis light transmittance through tinted contact lenses and the effect of color on values.

PubMed

Osuagwu, Uchechukwu L; Ogbuehi, Kelechi C

2014-06-01

To assess the transmittance, in the 200-700nm electromagnetic radiation spectrum, by popularly used tinted soft contact lenses (CLs). The spectra transmittances of ultraviolet (UV)-blocking (I Day Acuvue Define, Freshlook ONE DAY) and non-UV-blocking (Durasoft 3, Tutti, and NeoCosmo) tinted soft CLs were tested. The transmittance of each lens, including nine different colors of Freshlook CL was recorded on spectrophotometer, and the data used to also calculate a UV protection factor (PF) for each lens brand tested, with a higher value indicating a higher level of protection. The UV-blocking CLs significantly reduced UVC, UVB & UVA transmission and thereby meet the American National Standards Institution standard for class 2 UV blockers: a maximum of 30% transmittance of UVA and 5% transmittance of UVB wavelengths. In contrast, the Durasoft 3, Tutti, and NeoCosmo CLs demonstrated negligible UV-blockage. The Acuvue Define CL offered the greatest protection from UVC (PF=69) and UVB (PF=55), but with only 35% luminous transmittance, while the Freshlook CL (especially gemstone green) offered the best protection from UVA (PF=24) and showed about 55% translucency. Overall, the UV-blocking CLs performed equally well across the UV spectrum. Different colors of Freshlook CL transmitted statistically and clinically significantly different amounts of visible light but similar amounts of UVR. Freshlook and Acuvue Define CLs which are designated as UV-blockers significantly reduced UVR transmission to safe levels whereas Tutti, NeoCosmo and Durasoft 3 did not. Transmission within the Freshlook CL family was more dependent on color in the visible light spectrum, but not in the UV-spectrum, where the gemstone green performing best among the tested colors. Copyright © 2013 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Can CT-based patient-matched instrumentation achieve consistent rotational alignment in knee arthroplasty?

PubMed

Tibesku, C O; Innocenti, B; Wong, P; Salehi, A; Labey, L

2012-02-01

Long-term success of contemporary total knee replacements relies to a large extent on proper implant alignment. This study was undertaken to test whether specimen-matched cutting blocks based on computed axial tomography (CT) scans could provide accurate rotational alignment of the femoral component. CT scans of five fresh frozen full leg cadaver specimens, equipped with infrared reflective markers, were used to produce a specimen-matched femoral cutting block. Using those blocks, the bone cuts were made to implant a bi-compartmental femoral component. Rotational alignment of the components in the horizontal plane was determined using an optical measurement system and compared with all relevant rotational reference axes identified on the CT scans. Average rotational alignment for the bi-compartmental component in the horizontal plane was 1.9° (range 0°-6.3°; standard deviation 2.6°). One specimen that showed the highest deviation from the planned alignment also featured a completely degraded medial articular surface. The CT-based specimen-matched cutting blocks achieved good rotational alignment accuracy except for one specimen with badly damaged cartilage. In such cases, imaging techniques that visualize the cartilage layer might be more suitable to design cutting blocks, as they will provide a better fit and increased surface support.

A polyvalent hybrid protein elicits antibodies against the diverse allelic types of block 2 in Plasmodium falciparum merozoite surface protein 1.

PubMed

Tetteh, Kevin K A; Conway, David J

2011-10-13

Merozoite surface protein 1 (MSP1) of Plasmodium falciparum has been implicated as an important target of acquired immunity, and candidate components for a vaccine include polymorphic epitopes in the N-terminal polymorphic block 2 region. We designed a polyvalent hybrid recombinant protein incorporating sequences of the three major allelic types of block 2 together with a composite repeat sequence of one of the types and N-terminal flanking T cell epitopes, and compared this with a series of recombinant proteins containing modular sub-components and similarly expressed in Escherichia coli. Immunogenicity of the full polyvalent hybrid protein was tested in both mice and rabbits, and comparative immunogenicity studies of the sub-component modules were performed in mice. The full hybrid protein induced high titre antibodies against each of the major block 2 allelic types expressed as separate recombinant proteins and against a wide range of allelic types naturally expressed by a panel of diverse P. falciparum isolates, while the sub-component modules had partial antigenic coverage as expected. This encourages further development and evaluation of the full MSP1 block 2 polyvalent hybrid protein as a candidate blood-stage component of a malaria vaccine. Copyright © 2011 Elsevier Ltd. All rights reserved.

Anesthetic efficacy of the intraosseous injection after an inferior alveolar nerve block.

PubMed

Dunbar, D; Reader, A; Nist, R; Beck, M; Meyers, W J

1996-09-01

The purpose of this study was to determine the contribution of the intraosseous (IO) injection to the inferior alveolar nerve (IAN) block in human first molars. Using a repeated-measures design, 40 subjects randomly received either a combination IAN block + IO injection (on the distal of the first molar) using 2% lidocaine with 1:100,000 epinephrine or an IAN block+mock IO injection (gingival penetration only) at two successive appointments. The first molar and adjacent teeth, and contralateral canine (+/-controls) were blindly tested with an Analytic Technology pulp tester at 2-min cycles for 60 min. An 80 reading was used as the criterion for pulpal anesthesia. One hundred percent of the subjects had lip numbness with the IAN block. For the first molar, anesthetic success, defined as achieving an 80 reading within 15 min and keeping this reading for 60 min, was 42% with the IAN and 90% with the IAN + IO. Anesthetic failure defined as never achieving two 80 readings during the 60 min was 32% with the IAN and 0% with the IAN + IO. The onset of anesthesia was immediate with the IO injection. Eighty percent of the subjects sampled had a subjective increase in heart rate with the IO injection. The IO injection and postinjection questionnaire recorded low pain ratings.

Signal processing and display interface studies. [performance tests - design analysis/equipment specifications

NASA Technical Reports Server (NTRS)

1975-01-01

Signal processing equipment specifications, operating and test procedures, and systems design and engineering are described. Five subdivisions of the overall circuitry are treated: (1) the spectrum analyzer; (2) the spectrum integrator; (3) the velocity discriminator; (4) the display interface; and (5) the formatter. They function in series: (1) first in analog form to provide frequency resolution, (2) then in digital form to achieve signal to noise improvement (video integration) and frequency discrimination, and (3) finally in analog form again for the purpose of real-time display of the significant velocity data. The formatter collects binary data from various points in the processor and provides a serial output for bi-phase recording. Block diagrams are used to illustrate the system.

Designing high-performance cost-efficient embedded SRAM in deep-submicron era

NASA Astrophysics Data System (ADS)

Kobozeva, Olga; Venkatraman, Ramnath; Castagnetti, Ruggero; Duan, Franklin; Kamath, Arvind; Ramesh, Shiva

2004-05-01

We have previously presented the smallest and fastest 6 Transistor (6T)-Static Random Access Memories (SRAM) bitcells for System-on-Chip (SoC) high-density (HD) memories in 0.18 μm and 0.13 μm technologies. Our 1.87 μm2 6TSRAM bitcell with cell current of 47 μA and industry lowest soft error rate (0.35 FIT/Kbit) is used to assemble memory blocks embedded into SoC designs in 0.13 μm process technology. Excellent performance is achieved at a low overall cost, as our bitcells are based on standard CMOS process and demonstrate high yields in manufacturing. This paper discusses our methodology of embedded SRAM bitcell design. The key aspects of our approach are: 1) judicious selection of tightest achievable yet manufacturable design rules to build the cell; 2) compatibility with standard Optical Proximity Correction (OPC) flow; 3) use of parametric testing and yield analysis to achieve excellent design robustness and manufacturability. A thorough understanding of process limitations, particularly those related to photolithography was critical to the successful design and manufacturing of our aggressive, yet robust SRAM bitcells. The patterning of critical layers, such as diffusion, poly gate, contact and metal 1 has profound implications on functionality, electrical performance and manufacturability of memories. We have conducted the development of SRAM bitcells using two approaches for OPC: a) "manual" OPC, wherein the bitcell layout of each of the critical layers is achieved using iterative improvement of layout & aerial image simulation and b) automated OPC-compatible design, wherein the drawn bitcell layout becomes a subject of a full chip OPC. While manual-OPC remains a popular option, automated OPC-compatible bitcell design is very attractive, as it does not require additional development costs to achieve fab-to-fab portability. In both cases we have obtained good results with respect to patterning of the critical layers, electrical performance of the bitcell and memory yields. A critical part of our memory technology development effort is the design of memory-specific test structures that are used for: a) verifying electrical characteristics of SRAM transistors and b) confirming the robustness of the design rules used within the SRAM cell. In addition to electrical test structures, we have a fully functional SRAM test chip called RAMPCM that is composed of sub-blocks each designated to evaluate the robustness of a specific critical design rule used within the bitcells. The results from the electrical testing and RAMPCM yield analysis are used to identify opportunities for improvements in the layout design. The paper will also suggest some techniques that can result in more design friendly OPC solutions. Our work indicates that future IC designs can benefit from an automated OPC tool that can intelligently handle layout modifications according to design priorities.

Solar heating and cooling system design and development

NASA Technical Reports Server (NTRS)

1978-01-01

Application surveys and performance studies were conducted to determine a solar heating and hot water configuration that could be used in a variety of applications, and to identify subsystem modules that could be utilized in a building block fashion to adapt hardware items to single and multi-family residential and commercial systems. Topics discussed include: subsystem development for the solar collectors, controls, other components, energy management module, and the heating system configuration test. Operational tests conducted at an Illinois farmhouse, and a YWCA in Spokane, Washington are discussed.

Initial test results from a prototype, 20 kW helium charged Stirling engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clarke, M.A.; Taylor, D.R.

An alpha-configuration, helium charged Stirling engine with a predicted output of 20 kW indicated power has been developed by a British consortium of universities and industrial companies. The work performed by the Royal Naval Engineering College has been in computer assisted design and component testing, with future plans for full engine trials during 1984/85. The scope of this paper is to outline the data obtained during motoring trials of the engine block and crankcase assembly, together with details of modifications incorporated in the various components.

Integrated Resilient Aircraft Control Project Full Scale Flight Validation

NASA Technical Reports Server (NTRS)

Bosworth, John T.

2009-01-01

Objective: Provide validation of adaptive control law concepts through full scale flight evaluation. Technical Approach: a) Engage failure mode - destabilizing or frozen surface. b) Perform formation flight and air-to-air tracking tasks. Evaluate adaptive algorithm: a) Stability metrics. b) Model following metrics. Full scale flight testing provides an ability to validate different adaptive flight control approaches. Full scale flight testing adds credence to NASA's research efforts. A sustained research effort is required to remove the road blocks and provide adaptive control as a viable design solution for increased aircraft resilience.

Cattaraugus Creek Harbor, New York General Design Memorandum. Phase II (Detailed Design). Volume I. Main Report-GDM II.

DTIC Science & Technology

1976-03-01

of the abetract entered In Block 20, If different from Report) I$. SUPPLEMENTARY NOTES .4 19. KEY WORDS (Continue on reverse aide If neceesary and...Identify by block number) Harbors Cattaraugus Creek Flood Control 20O T’rlq 4CT Caiweut -t reverse se 0 neceeeely mid Identify by block number) The... blocked by the sand bar and lake ice at the creek mouth. During discharges developed by the com- bination of rainfall and snow melt, ice jams raise the

Around Marshall

NASA Image and Video Library

1962-10-26

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This construction photo, taken October 26, 1962, depicts a view of the Block House tunnel opening.

Around Marshall

NASA Image and Video Library

1962-08-17

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This construction photo taken August 17, 1962 depicts a back side view of the Block House.

Around Marshall

NASA Image and Video Library

1962-11-15

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This construction photo, taken November 15, 1962, depicts a view of the Block House.

Around Marshall

NASA Image and Video Library

1962-10-08

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This construction photo, taken October 8, 1962, depicts a front view of the Block House nearing completion.

Around Marshall

NASA Image and Video Library

1962-01-23

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This photo, taken January 23, 1962, shows the excavation of the Block House site.

Around Marshall

NASA Image and Video Library

1962-02-02

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This photo, taken February 2, 1962, shows the excavation of the Block House site.

Embeddable Reconfigurable Neuroprocessors

NASA Technical Reports Server (NTRS)

Daud, Taher; Duong, Tuan; Langenbacher, Harry; Tran, Mua; Thakoor, Anil

1993-01-01

Reconfigurable and cascadable building block neural network chips, fabricated using analog VLSI design tools, are interfaced to a PC. The building block chip designs, the cascadability and the hardware-in-the-loop supervised learning aspects of these chips are described.

Design and testing of the first 2D Prototype Vertically Integrated Pattern Recognition Associative Memory

NASA Astrophysics Data System (ADS)

Liu, T.; Deptuch, G.; Hoff, J.; Jindariani, S.; Joshi, S.; Olsen, J.; Tran, N.; Trimpl, M.

2015-02-01

An associative memory-based track finding approach has been proposed for a Level 1 tracking trigger to cope with increasing luminosities at the LHC. The associative memory uses a massively parallel architecture to tackle the intrinsically complex combinatorics of track finding algorithms, thus avoiding the typical power law dependence of execution time on occupancy and solving the pattern recognition in times roughly proportional to the number of hits. This is of crucial importance given the large occupancies typical of hadronic collisions. The design of an associative memory system capable of dealing with the complexity of HL-LHC collisions and with the short latency required by Level 1 triggering poses significant, as yet unsolved, technical challenges. For this reason, an aggressive R&D program has been launched at Fermilab to advance state of-the-art associative memory technology, the so called VIPRAM (Vertically Integrated Pattern Recognition Associative Memory) project. The VIPRAM leverages emerging 3D vertical integration technology to build faster and denser Associative Memory devices. The first step is to implement in conventional VLSI the associative memory building blocks that can be used in 3D stacking; in other words, the building blocks are laid out as if it is a 3D design. In this paper, we report on the first successful implementation of a 2D VIPRAM demonstrator chip (protoVIPRAM00). The results show that these building blocks are ready for 3D stacking.

Design and testing of the first 2D Prototype Vertically Integrated Pattern Recognition Associative Memory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, T.; Deptuch, G.; Hoff, J.

An associative memory-based track finding approach has been proposed for a Level 1 tracking trigger to cope with increasing luminosities at the LHC. The associative memory uses a massively parallel architecture to tackle the intrinsically complex combinatorics of track finding algorithms, thus avoiding the typical power law dependence of execution time on occupancy and solving the pattern recognition in times roughly proportional to the number of hits. This is of crucial importance given the large occupancies typical of hadronic collisions. The design of an associative memory system capable of dealing with the complexity of HL-LHC collisions and with the shortmore » latency required by Level 1 triggering poses significant, as yet unsolved, technical challenges. For this reason, an aggressive R&D program has been launched at Fermilab to advance state of-the-art associative memory technology, the so called VIPRAM (Vertically Integrated Pattern Recognition Associative Memory) project. The VIPRAM leverages emerging 3D vertical integration technology to build faster and denser Associative Memory devices. The first step is to implement in conventional VLSI the associative memory building blocks that can be used in 3D stacking, in other words, the building blocks are laid out as if it is a 3D design. In this paper, we report on the first successful implementation of a 2D VIPRAM demonstrator chip (protoVIPRAM00). The results show that these building blocks are ready for 3D stacking.« less

Development and evaluation of elastomeric materials for geothermal applications. Annual report, October 1977-December 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mueller, W.A.; Kalfayan, S.H.; Reilly, W.W.

1979-05-15

The research involved formulation of commercially available materials and synthesis of new elastomers. Formulation studies at JPL and elsewhere produced a material having about 250-350 psi tensile strength and 30 to 80% elongation at 260/sup 0/C for at least 24 hours in simulated brine. The relationship between these laboratory test results and sealing performance in actual or simulated test conditions is not entirely clear; however, it is believed that no conventional formation or casing packer design is likely to perform well using these materials. The synthetic effort focused on high temperature block copolymers and development of curable polystyrene. Procedures weremore » worked out for synthesizing these new materials. Initial results with heat-cured unfilled polystyrene gum at 260/sup 0/C indicated a tensile strength of about 50 psi. Cast films of the first sample of polyphenyl quinoxaline-polystyrene block copolymer, which has a graft-block structure consisting of a polystyrene chain with pendant polyphenyl quinoxaline groups, showed elastomeric behavior in the required temperature range. Its tensile strength and elongation at 260/sup 0/C were 220 to 350 psi and 18 to 36%, respectively. All of these materials also showed satisfactory hydrolytic stability. A procedure for the synthesis of a linear block copolymer of this type has been devised, and the required new intermediates have been synthesized and characterized. A description of the previous year's work is included in an appendix.« less

Electrical stimulation during skill training with a therapeutic glove enhances the induction of cortical plasticity and has a positive effect on motor memory.

PubMed

Christova, Monica; Rafolt, Dietmar; Golaszewski, Stefan; Nardone, Raffaele; Gallasch, Eugen

2014-08-15

To examine whether afferent stimulation of hand muscles has a facilitating effect on motor performance, learning and cortical excitability, healthy subjects were trained on the grooved pegboard test (GTP) while wearing a mesh glove (MG) with incorporated electrical stimulation. Three study groups (n=12) were compared in a between subjects design, the bare handed (BH), gloved (MG) and gloved with electrical stimulation (MGS) groups. Motor performance was assessed by the GPT completion time across 4 training blocks, and further one block was retested 7 days later to determine the off-line effects. On-line learning was obtained by normalizing the completion time values to the first training block, and off-line learning was obtained by normalizing the retest values to the last training block. Cortical excitability was assessed via single and paired-pulse transcranial magnetic stimulation (TMS) at pre-training, post-training and 30 min post-training. Motor evoked potential recruitment curve, short-latency intracortical inhibition and intracortical facilitation were estimated from the TMS assessments. Motor performance across all 4 training blocks was poor in the MG and MGS groups, while on-line learning was not affected by wearing the glove or by afferent stimulation. However, off-line learning, tested 7 days after training, was improved in the MGS group compared to the MG group. In addition, post-training corticospinal excitability was increased in the MGS group. It can be concluded that afferent stimulation improves off-line learning and thus has a positive effect on motor memory, likely due to LTP-like cortical plasticity in the consolidation phase. Copyright © 2014 Elsevier B.V. All rights reserved.

Protograph LDPC Codes Over Burst Erasure Channels

NASA Technical Reports Server (NTRS)

Divsalar, Dariush; Dolinar, Sam; Jones, Christopher

2006-01-01

In this paper we design high rate protograph based LDPC codes suitable for binary erasure channels. To simplify the encoder and decoder implementation for high data rate transmission, the structure of codes are based on protographs and circulants. These LDPC codes can improve data link and network layer protocols in support of communication networks. Two classes of codes were designed. One class is designed for large block sizes with an iterative decoding threshold that approaches capacity of binary erasure channels. The other class is designed for short block sizes based on maximizing minimum stopping set size. For high code rates and short blocks the second class outperforms the first class.

Approaching the design of a failsafe turbine monitor with simple microcontroller blocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zapolin, R.E.

1995-12-31

The proper approach to early instrumentation design for tasks like failsafe turbine monitoring permits meeting requirements without resorting to traditional complex special-purpose electronics. Instead a small network of basic microcontroller building blocks can split the effort with each block optimized for its portion of the overall system. This paper discusses approaching design by partitioning intricate system specifications to permit each block to be optimized to the safety level appropriate for its portion of the overall task while retaining and production and reliability advantages of having common simple modules. It illustrates that approach with a modular microcontroller-based speed monitor which metmore » user needs for the latest in power plant monitoring equipment.« less

AX-5 space suit bearing torque investigation

NASA Technical Reports Server (NTRS)

Loewenthal, Stuart; Vykukal, Vic; Mackendrick, Robert; Culbertson, Philip, Jr.

1990-01-01

The symptoms and eventual resolution of a torque increase problem occurring with ball bearings in the joints of the AX-5 space suit are described. Starting torques that rose 5 to 10 times initial levels were observed in crew evaluation tests of the suit in a zero-g water tank. This bearing problem was identified as a blocking torque anomaly, observed previously in oscillatory gimbal bearings. A large matrix of lubricants, ball separator designs and materials were evaluated. None of these combinations showed sufficient tolerance to lubricant washout when repeatedly cycled in water. The problem was resolved by retrofitting a pressure compensated, water exclusion seal to the outboard side of the bearing cavity. The symptoms and possible remedies to blocking are discussed.

Writing executable assertions to test flight software

NASA Technical Reports Server (NTRS)

Mahmood, A.; Andrews, D. M.; Mccluskey, E. J.

1984-01-01

An executable assertion is a logical statement about the variables or a block of code. If there is no error during execution, the assertion statement results in a true value. Executable assertions can be used for dynamic testing of software. They can be employed for validation during the design phase, and exception and error detection during the operation phase. The present investigation is concerned with the problem of writing executable assertions, taking into account the use of assertions for testing flight software. They can be employed for validation during the design phase, and for exception handling and error detection during the operation phase The digital flight control system and the flight control software are discussed. The considered system provides autopilot and flight director modes of operation for automatic and manual control of the aircraft during all phases of flight. Attention is given to techniques for writing and using assertions to test flight software, an experimental setup to test flight software, and language features to support efficient use of assertions.

ALIGNING JIG

DOEpatents

Culver, J.S.; Tunnell, W.C.

1958-08-01

A jig or device is described for setting or aligning an opening in one member relative to another member or structure, with a predetermined offset, or it may be used for measuring the amount of offset with which the parts have previously been sct. This jig comprises two blocks rabbeted to each other, with means for securing thc upper block to the lower block. The upper block has fingers for contacting one of the members to be a1igmed, the lower block is designed to ride in grooves within the reference member, and calibration marks are provided to determine the amount of offset. This jig is specially designed to align the collimating slits of a mass spectrometer.

Population Blocks.

ERIC Educational Resources Information Center

Smith, Martin H.

1992-01-01

Describes an educational game called "Population Blocks" that is designed to illustrate the concept of exponential growth of the human population and some potential effects of overpopulation. The game material consists of wooden blocks; 18 blocks are painted green (representing land), 7 are painted blue (representing water); and the remaining…

NUCLEAR REACTOR CORE DESIGN

DOEpatents

Mahlmeister, J.E.; Peck, W.S.; Haberer, W.V.; Williams, A.C.

1960-03-22

An improved core design for a sodium-cooled, graphitemoderated nuclear reactor is described. The improved reactor core comprises a number of blocks of moderator material, each block being in the shape of a regular prism. A number of channels, extending the length of each block, are disposed around the periphery. When several blocks are placed in contact to form the reactor core, the channels in adjacent blocks correspond with each other to form closed conduits extending the length of the core. Fuel element clusters are disposed in these closed conduits, and liquid coolant is forced through the annulus between the fuel cluster and the inner surface of the conduit. In a preferred embodiment of the invention, the moderator blocks are in the form of hexagonal prisms with longitudinal channels cut into the corners of the hexagon. The main advantage of an "edge-loaded" moderator block is that fewer thermal neutrons are absorbed by the moderator cladding, as compared with a conventional centrally loaded moderator block.

Determining the Mechanical Properties of Lattice Block Structures

NASA Technical Reports Server (NTRS)

Wilmoth, Nathan

2013-01-01

Lattice block structures and shape memory alloys possess several traits ideal for solving intriguing new engineering problems in industries such as aerospace, military, and transportation. Recent testing at the NASA Glenn Research Center has investigated the material properties of lattice block structures cast from a conventional aerospace titanium alloy as well as lattice block structures cast from nickel-titanium shape memory alloy. The lattice block structures for both materials were sectioned into smaller subelements for tension and compression testing. The results from the cast conventional titanium material showed that the expected mechanical properties were maintained. The shape memory alloy material was found to be extremely brittle from the casting process and only compression testing was completed. Future shape memory alloy lattice block structures will utilize an adjusted material composition that will provide a better quality casting. The testing effort resulted in baseline mechanical property data from the conventional titanium material for comparison to shape memory alloy materials once suitable castings are available.

Impairment of visuospatial/visuoconstructional skills in multiple sclerosis patients: the correlation with regional lesion load and subcortical atrophy.

PubMed

Marasescu, R; Cerezo Garcia, M; Aladro Benito, Y

2016-04-01

About 20% to 26% of patients with multiple sclerosis (MS) show alterations in visuospatial/visuoconstructive (VS-VC) skills even though temporo-parieto-occipital impairment is a frequent finding in magnetic resonance imaging. No studies have specifically analysed the relationship between these functions and lesion volume (LV) in these specific brain areas. To evaluate the relationship between VS-VC impairment and magnetic resonance imaging temporo-parieto-occipital LV with subcortical atrophy in patients with MS. Of 100 MS patients undergoing a routine neuropsychological evaluation, 21 were selected because they displayed VS-VC impairments in the following tests: Incomplete picture, Block design (WAIS-III), and Rey-Osterrieth complex figure test. We also selected 13 MS patients without cognitive impairment (control group). Regional LV was measured in FLAIR and T1-weighted images using a semiautomated method; subcortical atrophy was measured by bicaudate ratio and third ventricle width. Partial correlations (controlling for age and years of school) and linear regression analysis were employed to analyse correlations between magnetic resonance imaging parameters and cognitive performance. All measures of LV and brain atrophy were significantly higher in patients with cognitive impairment. Regional LV, bicaudate ratio, and third ventricle width are significantly and inversely correlated with cognitive performance; the strongest correlation was between third ventricle width and VC performance (Block design: P=.001; Rey-Osterrieth complex figure: P<.000). In the multivariate analysis, third ventricle width only had a significant effect on performance of VC tasks (Block design: P=.000; Rey-Osterrieth complex figure: P=.000), and regional FLAIR VL was linked to the VS task (Incomplete picture; P=.002). Measures of subcortical atrophy explain the variations in performance on visuocostructive tasks, and regional FLAIR VL measures are linked to VS tasks. Copyright © 2015 Sociedad Española de Neurología. Published by Elsevier España, S.L.U. All rights reserved.

Design of a rear anamorphic attachment for digital cinematography

NASA Astrophysics Data System (ADS)

Cifuentes, A.; Valles, A.

2008-09-01

Digital taking systems for HDTV and now for the film industry present a particularly challenging design problem for rear adapters in general. The thick 3-channel prism block in the camera provides an important challenge in the design. In this paper the design of a 1.33x rear anamorphic attachment is presented. The new design departs significantly from the traditional Bravais condition due to the thick dichroic prism block. Design strategies for non-rotationally symmetric systems and fields of view are discussed. Anamorphic images intrinsically have a lower contrast and less resolution than their rotationally symmetric counterparts, therefore proper image evaluation must be considered. The interpretation of the traditional image quality methods applied to anamorphic images is also discussed in relation to the design process. The final design has a total track less than 50 mm, maintaining the telecentricity of the digital prime lens and taking full advantage of the f/1.4 prism block.

16 CFR Figure 1 to Part 1513 - Wedge Block for Tests in § 1513.4 (a), (b), and (c)

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Wedge Block for Tests in § 1513.4 (a), (b), and (c) 1 Figure 1 to Part 1513 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL... Block for Tests in § 1513.4 (a), (b), and (c) ER22DE99.002 ...

Simscape Modeling Verification in the Simulink Development Environment

NASA Technical Reports Server (NTRS)

Volle, Christopher E. E.

2014-01-01

The purpose of the Simulation Product Group of the Control and Data Systems division of the NASA Engineering branch at Kennedy Space Center is to provide a realtime model and simulation of the Ground Subsystems participating in vehicle launching activities. The simulation software is part of the Spaceport Command and Control System (SCCS) and is designed to support integrated launch operation software verification, and console operator training. Using Mathworks Simulink tools, modeling engineers currently build models from the custom-built blocks to accurately represent ground hardware. This is time consuming and costly due to required rigorous testing and peer reviews to be conducted for each custom-built block. Using Mathworks Simscape tools, modeling time can be reduced since there would be no custom-code developed. After careful research, the group came to the conclusion it is feasible to use Simscape's blocks in MatLab's Simulink. My project this fall was to verify the accuracy of the Crew Access Arm model developed using Simscape tools running in the Simulink development environment.

Primers to block the amplification of symbiotic apostome ciliate 18S rRNA gene in a PCR-based copepod diet study

NASA Astrophysics Data System (ADS)

Yi, Xiaoyan; Zhang, Huan; Liu, Guangxing

2014-05-01

Pelagic copepods play an important role in the marine food web. However, a full understanding of the ecological status of this zooplankton group depends on the careful study of their natural diets. In previous PCR-based copepod diet studies, we found many apostome ciliates that live symbiotically under the exoskeleton of the copepods, and their sequences were often over-represented in the 18S rRNA gene (18S rDNA) libraries. As a first step to address this issue, we designed three apostome ciliate 18S rDNA blocking primers, and tested their blocking efficiency against apostome ciliate 18s rDNA under various PCR conditions. Using a semi-quantitative PCR method, we optimized the conditions to efficiently amplify the 18S rDNA of the prey while simultaneously excluding the symbiotic apostome ciliates. This technique will facilitate PCR-based diet studies of copepods and other zooplankton in their natural environments.

Applying energy-conservation retrofits to standard army buildings: project design and initial energy data. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westervelt, E.T.; Northrup, G.R.; Allen, E.O.

1988-07-01

This report describes the initial and continuing efforts in a project demonstrating the energy performance of theoretically-based retrofit packages on as-found, standard-design Army buildings. Four standard building designs are being investigated: a motor-vehicle repair shop, the Type 64 (L-shaped) barracks, an enlisted-personnel mess hall, and a two-company, rolling-pin-shaped barracks for enlisted personnel. The Army has over 840 of these particular buildings. The objective of the project is to test the energy and cost performance of the retrofit packages, which include such measures as installing wall or ceiling insulation, replacing and/or blocking windows, partitioning areas of differing temperature, modifying air-handling equipment,more » modifying boiler controls, replacing lights, etc. To this end, energy data has been gathered from retrofitted and identical but nonretrofitted buildings for a test/reference comparison.« less

Centrosome-Based Mechanisms, Prognostics and Therapeutics in Prostate Cancer

DTIC Science & Technology

2006-12-01

progression of prostate carcinomas. The specific aims of the original proposal were designed to test several features of this model . 1. Are centrosome...features of this model . 1. Are centrosome defects present in early prostate cancer and can they predict aggressive disease? 2. Do pericentrin’s...cells, supports this model . The ability to block the cell cycle in prostate cells by depletion of any of 14 centrosome proteins identifies several

Should Aid Reward Performance? Evidence from a Field Experiment on Health and Education in Indonesia. NBER Working Paper No. 17892

ERIC Educational Resources Information Center

Olken, Benjamin A.; Onishi, Junko; Wong, Susan

2012-01-01

This paper reports an experiment in over 3,000 Indonesian villages designed to test the role of performance incentives in improving the efficacy of aid programs. Villages in a randomly-chosen one-third of subdistricts received a block grant to improve 12 maternal and child health and education indicators, with the size of the subsequent year's…

MDR/Omni-band Reconfigurable Terminal: Design Concept

DTIC Science & Technology

1998-09-01

tasks, data bases and major communications flows. Global issues relevant to most of the blocks are then covered. Finally the planned sequence of...and event logger that are detailed in later paragraphs. The BITE(built-in test equipment)/Debugger detail can be found separately in the Global Issues paragraphs...conditions. Every part of the simulator has a BITE/Debugger component, the general description of which is given in Global Issues . Simulator control

Software Development for the Hobby-Eberly Telescope's Segment Alignment Maintenance System using LABView

NASA Technical Reports Server (NTRS)

Hall, Drew P.; Ly, William; Howard, Richard T.; Weir, John; Rakoczy, John; Roe, Fred (Technical Monitor)

2002-01-01

The software development for an upgrade to the Hobby-Eberly Telescope (HET) was done in LABView. In order to improve the performance of the HET at the McDonald Observatory, a closed-loop system had to be implemented to keep the mirror segments aligned during periods of observation. The control system, called the Segment Alignment Maintenance System (SAMs), utilized inductive sensors to measure the relative motions of the mirror segments. Software was developed in LABView to tie the sensors, operator interface, and mirror-control motors together. Developing the software in LABView allowed the system to be flexible, understandable, and able to be modified by the end users. Since LABView is built using block diagrams, the software naturally followed the designed control system's block and flow diagrams, and individual software blocks could be easily verified. LABView's many built-in display routines allowed easy visualization of diagnostic and health-monitoring data during testing. Also, since LABView is a multi-platform software package, different programmers could develop the code remotely on various types of machines. LABView s ease of use facilitated rapid prototyping and field testing. There were some unanticipated difficulties in the software development, but the use of LABView as the software "language" for the development of SAMs contributed to the overall success of the project.

Durability of Bricks Coated with Red mud Based Geopolymer Paste

NASA Astrophysics Data System (ADS)

Singh, Smita; Basavanagowda, S. N.; Aswath, M. U.; Ranganath, R. V.

2016-09-01

The present study is undertaken to assess the durability of concrete blocks coated with red mud - fly ash based geopolymer paste. Concrete blocks of size 200 x 200 x 100mm were coated with geopolymer paste synthesized by varying the percentages of red mud and fly ash. Uncoated concrete blocks were also tested for the durability for comparison. In thermal resistance test, the blocks were subjected to 600°C for an hour whereas in acid resistance test, they were kept in 5% sulphuric acid solution for 4 weeks. The specimens were thereafter studied for surface degradation, strength loss and weight loss. Pastes with red mud percentage greater than 50% developed lot of shrinkage cracks. The blocks coated with 30% and 50% red mud paste showed better durability than the other blocks. The use of blocks coated with red mud - fly ash geopolymer paste improves the aesthetics, eliminates the use of plaster and improves the durability of the structure.

Estimation of the return period of rockfall blocks according to their size

NASA Astrophysics Data System (ADS)

De Biagi, Valerio; Lia Napoli, Maria; Barbero, Monica; Peila, Daniele

2017-01-01

With reference to the rockfall risk estimation and the planning of rockfall protection devices, one of the most critical and most discussed problems is the correct definition of the design block by taking into account its return period. In this paper, a methodology for the assessment of the design block linked with its return time is proposed and discussed, following a statistical approach. The procedure is based on the survey of the blocks that were already detached from the slope and had accumulated at the foot of the slope in addition to the available historical data.

Blocking Spatial Navigation Across Environments That Have a Different Shape

PubMed Central

2015-01-01

According to the geometric module hypothesis, organisms encode a global representation of the space in which they navigate, and this representation is not prone to interference from other cues. A number of studies, however, have shown that both human and non-human animals can navigate on the basis of local geometric cues provided by the shape of an environment. According to the model of spatial learning proposed by Miller and Shettleworth (2007, 2008), geometric cues compete for associative strength in the same manner as non-geometric cues do. The experiments reported here were designed to test if humans learn about local geometric cues in a manner consistent with the Miller-Shettleworth model. Experiment 1 replicated previous findings that humans transfer navigational behavior, based on local geometric cues, from a rectangle-shaped environment to a kite-shaped environment, and vice versa. In Experiments 2 and 3, it was observed that learning about non-geometric cues blocked, and were blocked by, learning about local geometric cues. The reciprocal blocking observed is consistent with associative theories of spatial learning; however, it is difficult to explain the observed effects with theories of global-shape encoding in their current form. PMID:26569017

Experimental design matters for statistical analysis: how to handle blocking.

PubMed

Jensen, Signe M; Schaarschmidt, Frank; Onofri, Andrea; Ritz, Christian

2018-03-01

Nowadays, evaluation of the effects of pesticides often relies on experimental designs that involve multiple concentrations of the pesticide of interest or multiple pesticides at specific comparable concentrations and, possibly, secondary factors of interest. Unfortunately, the experimental design is often more or less neglected when analysing data. Two data examples were analysed using different modelling strategies. First, in a randomized complete block design, mean heights of maize treated with a herbicide and one of several adjuvants were compared. Second, translocation of an insecticide applied to maize as a seed treatment was evaluated using incomplete data from an unbalanced design with several layers of hierarchical sampling. Extensive simulations were carried out to further substantiate the effects of different modelling strategies. It was shown that results from suboptimal approaches (two-sample t-tests and ordinary ANOVA assuming independent observations) may be both quantitatively and qualitatively different from the results obtained using an appropriate linear mixed model. The simulations demonstrated that the different approaches may lead to differences in coverage percentages of confidence intervals and type 1 error rates, confirming that misleading conclusions can easily happen when an inappropriate statistical approach is chosen. To ensure that experimental data are summarized appropriately, avoiding misleading conclusions, the experimental design should duly be reflected in the choice of statistical approaches and models. We recommend that author guidelines should explicitly point out that authors need to indicate how the statistical analysis reflects the experimental design. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Compressive Properties of Metal Matrix Syntactic Foams in Free and Constrained Compression

NASA Astrophysics Data System (ADS)

Orbulov, Imre Norbert; Májlinger, Kornél

2014-06-01

Metal matrix syntactic foam (MMSF) blocks were produced by an inert gas-assisted pressure infiltration technique. MMSFs are advanced hollow sphere reinforced-composite materials having promising application in the fields of aviation, transport, and automotive engineering, as well as in civil engineering. The produced blocks were investigated in free and constrained compression modes, and besides the characteristic mechanical properties, their deformation mechanisms and failure modes were studied. In the tests, the chemical composition of the matrix material, the size of the reinforcing ceramic hollow spheres, the applied heat treatment, and the compression mode were considered as investigation parameters. The monitored mechanical properties were the compressive strength, the fracture strain, the structural stiffness, the fracture energy, and the overall absorbed energy. These characteristics were strongly influenced by the test parameters. By the proper selection of the matrix and the reinforcement and by proper design, the mechanical properties of the MMSFs can be effectively tailored for specific and given applications.

Cigarette filter ventilation is a defective design because of misleading taste, bigger puffs, and blocked vents.

PubMed

Kozlowski, L T; O'Connor, R J

2002-03-01

To review tobacco industry documents on filter ventilation in light of published studies and to explore the role of filter ventilation in the design of cigarettes that deliver higher smoke yields to smokers than would be expected from standard machine smoked tests (Federal Trade Commission (FTC), International Organization for Standardization (ISO)). Searched from November 1999 to November 2000 internet databases of industry documents (www.pmdocs.com, www.rjrtdocs.com, www.lorillarddocs.com, www.bw.aalatg.com, www.cdc.gov/tobacco/industrydocs, www.tobaccodocuments.org, www.tobaccopapers.org, www.hlth.gov.bc.ca/Guildford, www.cctc.ca/ncth/Guildford, www.cctc.ca/ncth/Guildford2) for documents related to filter ventilation. Documents found dated from 1955 through 1994. Those documents judged to contain the most relevant information or data on filter ventilation related to cigarette taste and compensatory smoking, while also trying to avoid redundancy from various documents deriving from the same underlying data. Filter ventilation is a crucial design feature creating three main problems for lower tar cigarettes as measured by official smoking machine testing. Firstly, it misleadingly makes cigarettes taste lighter and milder, and, therefore, they appear less dangerous to smokers. Secondly, it promotes compensation mainly by facilitating the taking of larger puffs. Thirdly, for very heavily ventilated cigarettes (that is, > 65% filter air dilution), behavioural blocking of vents with lips or fingers is an additional contributor to compensatory smoking. These three effects are found in industry research as well as published research. Filter ventilation is a dangerous, defective technology that should be abandoned in less hazardous nicotine delivery systems. Health interested groups should test cigarettes in a way that reflects compensatory smoking. Lower tar (vented filter) cigarettes should be actively countermarketed.

Associations Between Sleep Duration Patterns and Behavioral/Cognitive Functioning at School Entry

PubMed Central

Touchette, Évelyne; Petit, Dominique; Séguin, Jean R.; Boivin, Michel; Tremblay, Richard E.; Montplaisir, Jacques Y.

2007-01-01

Objective: The aim of the study was to investigate the associations between longitudinal sleep duration patterns and behavioral/cognitive functioning at school entry. Design, Setting, and Participants: Hyperactivity-impulsivity (HI), inattention, and daytime sleepiness scores were measured by questionnaire at 6 years of age in a sample of births from 1997 to 1998 in a Canadian province (N=1492). The Peabody Picture Vocabulary Test - Revised (PPVT-R) was administered at 5 years of age and the Block Design subtest (WISC-III) was administered at 6 years of age. Sleep duration was reported yearly by the children's mothers from age 2.5 to 6 years. A group-based semiparametric mixture model was used to estimate developmental patterns of sleep duration. The relationships between sleep duration patterns and both behavioral items and neurodevelopmental tasks were tested using weighted multivariate logistic regression models to control for potentially confounding psychosocial factors. Results: Four sleep duration patterns were identified: short persistent (6.0%), short increasing (4.8%),10-hour persistent (50.3%), and 11-hour persistent (38.9%). The association of short sleep duration patterns with high HI scores (P=0.001), low PPVT-R performance (P=0.002), and low Block Design subtest performance (P=0.004) remained significant after adjusting for potentially confounding variables. Conclusions: Shortened sleep duration, especially before the age of 41 months, is associated with externalizing problems such as HI and lower cognitive performance on neurodevelopmental tests. Results highlight the importance of giving a child the opportunity to sleep at least 10 hours per night throughout early childhood. Citation: Touchette E; Petit D; Séguin JR; Boivin M; Tremblay RE; Montplaisir JY. Associations between sleep duration patterns and behavioral/cognitive functioning at school entry. SLEEP 2007;30(9):1213-1219. PMID:17910393

Main-chain supramolecular block copolymers.

PubMed

Yang, Si Kyung; Ambade, Ashootosh V; Weck, Marcus

2011-01-01

Block copolymers are key building blocks for a variety of applications ranging from electronic devices to drug delivery. The material properties of block copolymers can be tuned and potentially improved by introducing noncovalent interactions in place of covalent linkages between polymeric blocks resulting in the formation of supramolecular block copolymers. Such materials combine the microphase separation behavior inherent to block copolymers with the responsiveness of supramolecular materials thereby affording dynamic and reversible materials. This tutorial review covers recent advances in main-chain supramolecular block copolymers and describes the design principles, synthetic approaches, advantages, and potential applications.

SRA Real Math Building Blocks PreK. What Works Clearinghouse Intervention Report

ERIC Educational Resources Information Center

What Works Clearinghouse, 2007

2007-01-01

"SRA Real Math Building Blocks PreK" (also referred to as "Building Blocks for Math") is a supplemental mathematics curriculum designed to develop preschool children's early mathematical knowledge through various individual and small- and large-group activities. It uses "Building Blocks for Math PreK" software,…

Teko: A block preconditioning capability with concrete example applications in Navier--Stokes and MHD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cyr, Eric C.; Shadid, John N.; Tuminaro, Raymond S.

This study describes the design of Teko, an object-oriented C++ library for implementing advanced block preconditioners. Mathematical design criteria that elucidate the needs of block preconditioning libraries and techniques are explained and shown to motivate the structure of Teko. For instance, a principal design choice was for Teko to strongly reflect the mathematical statement of the preconditioners to reduce development burden and permit focus on the numerics. Additional mechanisms are explained that provide a pathway to developing an optimized production capable block preconditioning capability with Teko. Finally, Teko is demonstrated on fluid flow and magnetohydrodynamics applications. In addition to highlightingmore » the features of the Teko library, these new results illustrate the effectiveness of recent preconditioning developments applied to advanced discretization approaches.« less

Teko: A block preconditioning capability with concrete example applications in Navier--Stokes and MHD

DOE PAGES

Cyr, Eric C.; Shadid, John N.; Tuminaro, Raymond S.

2016-10-27

This study describes the design of Teko, an object-oriented C++ library for implementing advanced block preconditioners. Mathematical design criteria that elucidate the needs of block preconditioning libraries and techniques are explained and shown to motivate the structure of Teko. For instance, a principal design choice was for Teko to strongly reflect the mathematical statement of the preconditioners to reduce development burden and permit focus on the numerics. Additional mechanisms are explained that provide a pathway to developing an optimized production capable block preconditioning capability with Teko. Finally, Teko is demonstrated on fluid flow and magnetohydrodynamics applications. In addition to highlightingmore » the features of the Teko library, these new results illustrate the effectiveness of recent preconditioning developments applied to advanced discretization approaches.« less

16 CFR Figure 1 to Part 1213 - Wedge Block for Tests in § 1213.4(a), (b), and (c)

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Wedge Block for Tests in § 1213.4(a), (b), and (c) 1 Figure 1 to Part 1213 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER... 1 to Part 1213—Wedge Block for Tests in § 1213.4(a), (b), and (c) ER22DE99.007 ...

Grid Block Design Based on Monte Carlo Simulated Dosimetry, the Linear Quadratic and Hug–Kellerer Radiobiological Models

PubMed Central

Gholami, Somayeh; Nedaie, Hassan Ali; Longo, Francesco; Ay, Mohammad Reza; Dini, Sharifeh A.; Meigooni, Ali S.

2017-01-01

Purpose: The clinical efficacy of Grid therapy has been examined by several investigators. In this project, the hole diameter and hole spacing in Grid blocks were examined to determine the optimum parameters that give a therapeutic advantage. Methods: The evaluations were performed using Monte Carlo (MC) simulation and commonly used radiobiological models. The Geant4 MC code was used to simulate the dose distributions for 25 different Grid blocks with different hole diameters and center-to-center spacing. The therapeutic parameters of these blocks, namely, the therapeutic ratio (TR) and geometrical sparing factor (GSF) were calculated using two different radiobiological models, including the linear quadratic and Hug–Kellerer models. In addition, the ratio of the open to blocked area (ROTBA) is also used as a geometrical parameter for each block design. Comparisons of the TR, GSF, and ROTBA for all of the blocks were used to derive the parameters for an optimum Grid block with the maximum TR, minimum GSF, and optimal ROTBA. A sample of the optimum Grid block was fabricated at our institution. Dosimetric characteristics of this Grid block were measured using an ionization chamber in water phantom, Gafchromic film, and thermoluminescent dosimeters in Solid Water™ phantom materials. Results: The results of these investigations indicated that Grid blocks with hole diameters between 1.00 and 1.25 cm and spacing of 1.7 or 1.8 cm have optimal therapeutic parameters (TR > 1.3 and GSF~0.90). The measured dosimetric characteristics of the optimum Grid blocks including dose profiles, percentage depth dose, dose output factor (cGy/MU), and valley-to-peak ratio were in good agreement (±5%) with the simulated data. Conclusion: In summary, using MC-based dosimetry, two radiobiological models, and previously published clinical data, we have introduced a method to design a Grid block with optimum therapeutic response. The simulated data were reproduced by experimental data. PMID:29296035

Novel High Efficient Organic Photovoltaic Materials

NASA Technical Reports Server (NTRS)

Sun, Sam; Haliburton, James; Fan, Zben; Taft, Charles; Wang, Yi-Qing; Maaref, Shahin; Mackey, Willie R. (Technical Monitor)

2001-01-01

In man's mission to the outer space or a remote site, the most abundant, renewable, nonpolluting, and unlimited external energy source is light. Photovoltaic (PV) materials can convert light into electrical power. In order to generate appreciable electrical power in space or on the Earth, it is necessary to collect sunlight from large areas due to the low density of sunlight, and this would be very costly using current commercially available inorganic solar cells. Future organic or polymer based solar cells seemed very attractive due to several reasons. These include lightweight, flexible shape, ultra-fast optoelectronic response time (this also makes organic PV materials attractive for developing ultra-fast photo detectors), tunability of energy band-gaps via molecular design, versatile materials synthesis and device fabrication schemes, and much lower cost on large-scale industrial production. It has been predicted that nano-phase separated block copolymer systems containing electron rich donor blocks and electron deficient acceptor blocks will facilitate the charge separation and migration due to improved electronic ultrastructure and morphology in comparison to current polymer composite photovoltaic system. This presentation will describe our recent progress in the design, synthesis and characterization of a novel donor-bridge-acceptor block copolymer system for potential high-efficient organic optoelectronic applications. Specifically, the donor block contains an electron donating alkyloxy derivatized polyphenylenevinylene, the acceptor block contains an electron withdrawing alkyl-sulfone derivatized polyphenylenevinylene, and the bridge block contains an electronically neutral non-conjugated aliphatic hydrocarbon chain. The key synthetic strategy includes the synthesis of each individual block first, then couple the blocks together. While the donor block stabilizes the holes, the acceptor block stabilizes the electrons. The bridge block is designed to hinder the electron-hole recombination. Thus, improved charge separation is expected. In addition, charge migration will also be facilitated due to the expected nano-phase separated and highly ordered block copolymer ultrastructural. The combination of all these factors will result in significant overall enhancement of photovoltaic power conversion efficiency.

Solar Power Satellite (SPS) solid-state antenna power combiner

NASA Technical Reports Server (NTRS)

1980-01-01

A low loss power-combining microstrip antenna suitable for solid state solar power satellite (SPS) application was developed. A unique approach for performing both the combining and radiating function in a single cavity-type circuit was verified, representing substantial refinements over previous demonstration models in terms of detailed geometry to obtain good matching and adequate bandwidth at the design frequency. The combiner circuit was designed, built, and tested and the overall results support the view that the solid state power-combining antenna approach is a viable candidate for a solid state SPS antenna building block.

Richard B. Russell Dam and Lake, Savannah River, Georgia and South Carolina Final Foundation Report, Concrete Dam, Embankments and Powerhouse. Volume 2. Appendices

DTIC Science & Technology

1989-10-03

Georgia. TESTED 8y CHEcKED BY REPORTED BY, C PHONE 0 WIRE *GVJ DE SAMPLED BY OATE : SAO FORM IS$ Page of 20 24 OCT So Previous editions of this fore are...block for bto; line system. Cos- - $514.00 PO)8 - Second Stage Dike VE - Mod D Change in design for portion of 2nd stage cofferdike near tie-in with...ATION (Coordinteat~ Station)N14; _______________________________________12. MANUFACTURER’S DESIGNATION OF DRILL. 3. DRILLING AGENCY d~l gjr GvA.IIw1

Programmable calculator as a data system controller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barth, A.W.; Strasburg, A.C.

Digital data techniques are in common use for analysis of analog information obtained in various tests, and systems have been developed which use a minicomputer as the central controller and data processor. Now, microprocessors allow new design approaches at considerably less cost. This report outlines an approach to system design based on the use of a programmable calculator as the data system controller. A block diagram of the calculator-controlled data system is shown. It was found that the programmable calculator provides a viable alternative to minicomputers or microprocessors for the development laboratory requiring digital data processing. 3 figures. (RWR)

76 FR 20451 - Unblocking of Specially Designated National and Blocked Person Pursuant to Executive Order 13566

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-12

... unblocking and removal from the list of Specially Designated Nationals and Blocked Persons (``SDN List'') of..., the Director of OFAC removed from the SDN List the individual listed below, whose property and...

Dendronized Metal Nanoparticles-Self-Organizing Building Blocks for the Design of New Functional Materials

DTIC Science & Technology

2016-04-01

characterization has just started.       The hybrids that we have synthesized are based on plasmonic gold and  silver   nanoparticles  (NPs) but  the concept  is...AFRL-AFOSR-UK-TR-2016-0010 Dendronized metal nanoparticles - self-organizing building blocks for the design of new functional materials Bertrand...2015 4. TITLE AND SUBTITLE Dendronized metal nanoparticles - self-organizing building blocks for the design of new functional materials 5a. CONTRACT

Combinatorics associated with inflections and bitangents of plane quartics

NASA Astrophysics Data System (ADS)

Gizatullin, M. Kh

2013-08-01

After a preliminary survey and a description of some small Steiner systems from the standpoint of the theory of invariants of binary forms, we construct a binary Golay code (of length 24) using ideas from J. Grassmann's thesis of 1875. One of our tools is a pair of disjoint Fano planes. Another application of such pairs and properties of plane quartics is a construction of a new block design on 28 objects. This block design is a part of a dissection of the set of 288 Aronhold sevens. The dissection distributes the Aronhold sevens into 8 disjoint block designs of this type.

The modeling of an automotive electronic control system and the application of optimizing methods

NASA Astrophysics Data System (ADS)

Zhang, Yansheng; Yang, Zhigang; Zhang, Xiang

2005-12-01

Now, MATLAB/SIMULINK software is popularly used by automotive electronic control designers to develop automotive electronic control systems and perform numerical simulations. But they will face problems, such as value initialization in the "integrator" block, conversion among different data types, selection of "if" block and "switch" block, realization of the "if-clause" under multiple options and the auto-switching control, etc. Taking as an example the designing of an Automated Mechanical Transmission (AMT) system, this paper discusses some techniques and methods for modeling the automotive electronic control system with MATLAB/SIMULINK, offering designers some successful examples.

A Comparison of Efficacy of Segmental Epidural Block versus Spinal Anaesthesia for Percutaneous Nephrolithotomy

PubMed Central

Nandanwar, Avinash S; Patil, Yogita; Baheti, Vidyasagar H.; Tanwar, Harshwardhan V.; Patwardhan, Sujata K.

2015-01-01

Introduction Percutaneous nephrolithotomy (PCNL) is done under general anaesthesia in most of the centres. Associated complications and cost are higher for general anaesthesia than for regional anaesthesia. Present study is designed to compare the efficacy of epidural block versus spinal anaesthesia with regards to intraoperative mean arterial pressure, heart rate, postoperative pain intensity, analgesic requirement, Postoperative complications and patient satisfaction in patients undergoing PCNL. Materials and Methods After taking Ethical Committee clearance, patients were randomly allocated into 2 groups using table of randomization (n= 40 each) Group E- Epidural block, Group S- Spinal block. Various parameters like intraoperative mean arterial pressure, heart rate, postoperative pain intensity, analgesic requirement, postoperative complications and patient satisfaction were studied in these groups. Statistical Analysis Quantitative data was analysed using unpaired t-test and qualitative data was analysed using chi-square test. Results Twenty four times in Epidural as compared to fifteen times in spinal anaesthesia two or more attempts required. Mean time (min) required to achieve the block of anaesthesia in group E and group S was 15.45±2.8 and 8.52±2.62 min respectively. Mean arterial pressure (MAP) at 5 min, 10 min and 15 min were significantly lower in spinal group as compared to epidural group. After 30 minutes, differences were not significant but still MAP was lower in spinal group. After 30 minutes difference in heart rate between two groups was statistically significant and higher rate recorded in spinal group till the end of 3 hours. Postoperative VAS score was significantly higher in spinal group and 4 hours onwards difference was highly significant. Postoperative Nausea Vomiting (PONV) Score was significantly higher in spinal group as compared to epidural group. Conclusion For PCNL, segmental epidural block is better than spinal anaesthesia in terms of haemodynamic stability, postoperative analgesia, patient satisfaction and reduced incidence of PONV. Epidural anaesthesia is difficult to execute and takes longer time to act as compared to spinal block which limits its use. PMID:26436021

Manuscript Architect: a Web application for scientific writing in virtual interdisciplinary groups

PubMed Central

Pietrobon, Ricardo; Nielsen, Karen C; Steele, Susan M; Menezes, Andreia P; Martins, Henrique; Jacobs, Danny O

2005-01-01

Background Although scientific writing plays a central role in the communication of clinical research findings and consumes a significant amount of time from clinical researchers, few Web applications have been designed to systematically improve the writing process. This application had as its main objective the separation of the multiple tasks associated with scientific writing into smaller components. It was also aimed at providing a mechanism where sections of the manuscript (text blocks) could be assigned to different specialists. Manuscript Architect was built using Java language in conjunction with the classic lifecycle development method. The interface was designed for simplicity and economy of movements. Manuscripts are divided into multiple text blocks that can be assigned to different co-authors by the first author. Each text block contains notes to guide co-authors regarding the central focus of each text block, previous examples, and an additional field for translation when the initial text is written in a language different from the one used by the target journal. Usability was evaluated using formal usability tests and field observations. Results The application presented excellent usability and integration with the regular writing habits of experienced researchers. Workshops were developed to train novice researchers, presenting an accelerated learning curve. The application has been used in over 20 different scientific articles and grant proposals. Conclusion The current version of Manuscript Architect has proven to be very useful in the writing of multiple scientific texts, suggesting that virtual writing by interdisciplinary groups is an effective manner of scientific writing when interdisciplinary work is required. PMID:15960855

Increased torsional stability by a novel femoral neck locking plate. The role of plate design and pin configuration in a synthetic bone block model.

PubMed

Brattgjerd, Jan Egil; Loferer, Martin; Niratisairak, Sanyalak; Steen, Harald; Strømsøe, Knut

2018-06-01

In undisplaced femoral neck fractures, internal fixation remains the main treatment, with mechanical failure as a frequent complication. As torsional stable fixation promotes femoral neck fracture healing, the Hansson Pinloc® System with a plate interlocking pins, was developed from the original hook pins. Since its effect on torsional stability is undocumented, the novel implant was compared with the original configurations. Forty-two proximal femur models custom made of two blocks of polyurethane foam were tested. The medial block simulated the cancellous head, while the lateral was laminated with a glass fiber filled epoxy sheet simulating trochanteric cortical bone. Two hollow metal cylinders with a circumferential ball bearing in between mimicked the neck, with a perpendicular fracture in the middle. Fractures were fixated by two or three independent pins or by five configurations involving the interlocking plate (two pins with an optional peg in a small plate, or three pins in a small, medium or large plate). Six torsional tests were performed on each configuration to calculate torsional stiffness, torque at failure and failure energy. The novel configurations improved parameters up to an average of 12.0 (stiffness), 19.3 (torque) and 19.9 (energy) times higher than the original two pins (P < 0.001). The plate, its size and its triangular configuration improved all parameters (P = 0.03), the plate being most effective, also preventing permanent failure (P < 0.001). The novel plate design with its pin configuration enhanced torsional stability. To reveal clinical relevance a clinical study is planned. Copyright © 2018 Elsevier Ltd. All rights reserved.

A Phenomenological Research Study on Writer's Block: Causes, Processes, and Results

ERIC Educational Resources Information Center

Bastug, Muhammet; Ertem, Ihsan Seyit; Keskin, Hasan Kagan

2017-01-01

Purpose: The purpose of this paper is to investigate the causes, processes of writer's block experienced by a group of classroom teacher candidates and its impact on them. Design/methodology/approach: The phenomenological design, which is a qualitative research design, was preferred in the research since it was aimed to investigate the causes,…

Design of field experiments: Influence of treatment response relative to standard deviation and blocking factor characteristics on efficient blocking strategy

USDA-ARS?s Scientific Manuscript database

Selection of experimental design can markedly influence efficiency of field research. This study used Monte Carlo simulations to compare the ability of different field experimental designs to distinguish defined treatment differences, and the paper concludes with a section on practical use of the in...

Strategic retrieval processing and the impact of knowing when a memory was first created.

PubMed

Roberts, J S; Tsivilis, D; Mayes, A R

2014-04-01

Retrieval orientation refers to a process where participants strategically alter how a memory cue is processed in response to different task demands. In the present study we explored whether retrieval orientation is influenced by knowing when an old stimulus was first encoded. Participants completed separate remember/know test blocks for old items from a recent delay (40min) and old items from a remote delay (48h). Manipulations at encoding ensured that performance levels were matched between these two blocks, thus avoiding confounds with differences in retrieval effort. Importantly, a third test block comprised old items from both delays randomly intermixed. As the nature of the old items varies unpredictably in the mixed block, it should not be possibly to adopt a specific retrieval orientation and the mixed block therefore acts as a control condition. Participants saw the words "mixed," "recent" or "remote" prior to each test block. Comparing ERPs from the recent and remote blocks permitted an investigation of whether participants alter their retrieval orientation in response to the specific length of the retention interval. Comparing ERPs from the pure (recent and remote) test blocks to ERPs from the mixed block permitted an investigation of whether delay information per se led to differences in retrieval strategy. Analysis of the ERP data found no differences between the recent and remote blocks. However, ERPs from these pure blocks were significantly less positive than ERPs from the mixed block from 200ms towards the end of the epoch. The findings suggest that the delay information was useful in a general sense and encouraged retrieval strategies distinct from those engaged in the mixed block. We speculate that such strategies might relate to whether or not the retrieval search is specific and constrained and/or whether processes that serve to reinstate the original encoding context are engaged. Copyright © 2014 Elsevier Inc. All rights reserved.

In Situ Resource-Based Lunar and Martian Habitat Structures Development at NASA/MSFC

NASA Technical Reports Server (NTRS)

Bodiford, Melanie P.; Fiske, Michael R.; McGregory, Walter; Pope, Regina D.

2005-01-01

As the nation prepares to return to the Moon and subsequently to Mars, it is apparent that the viability of long duration visits with appropriate radiation shielding/crew protection, hinges on the development of habitat structures, preferably in advance of a manned landing, and preferably utilizing in-situ resources. A relatively large number of habitat structure configurations can be developed from a relatively small set of in-situ resource-based construction products, including, blocks, raw regolith, reinforced concrete, and glass products. A much larger group of habitat designs can be developed when "imported" material are brought from Earth, including thin films and liners, and foldable, or expandable metal structures. These, and other technologies have been identified, and subjected to a rigorous trade study evaluation with respect to exploration and other performance criteria. In this paper, results of this trade study will be presented, as well as various habitat structure design concepts and concepts for construction automation. Results of initial tests aimed at concrete, block and glass production using Lunar regolith simulants will also be presented. Key issues and concerns will be discussed, as well as design concepts for a Lunar environment testbed to be developed at MSFC's Microgravity Development Laboratory. (MDL).

In-situ Resource-based Lunar and Martian Habitat Structures Development at NASA/MSFC

NASA Technical Reports Server (NTRS)

Bodiford, Melanie P.; Burks, Kevin H.; Fiske, Michael R.; Strong, Janet D.; McGregor, Walter

2005-01-01

As the nation prepares to return to the Moon and subsequently to Mars, it is apparent that the viability of long duration visits with appropriate radiation shielding/crew protection, hinges on the development of habitat structures, preferably in advance of a manned landing, and preferably utilizing in-situ resources. A relatively large number of habitat structure configurations can be developed from a relatively small set of in-situ resource-based construction products, including, blocks, raw regolith, reinforced concrete, and glass products. A much larger group of habitat designs can be developed when "imported" material are brought from Earth, including thin films and liners, and foldable, or expandable metal structures. These, and other technologies have been identified, and subjected to a rigorous trade study evaluation with respect to exploration and other performance criteria. In this paper, results of this trade study will be presented, as well as various habitat structure design concepts and concepts for construction automation. Results of initial tests aimed at concrete, block and glass production using Lunar regolith simulants will also be presented. Key issues and concerns will be discussed, as well as design concepts for a Lunar environment testbed to be developed at MSFC's Microgravity Development Laboratory (MDL).

Comparative evaluation of the amount of gingival displacement produced by three different gingival retraction systems: An in vivo study.

PubMed

Chaudhari, Jignesh; Prajapati, Paranjay; Patel, Jayanti; Sethuraman, Rajesh; Naveen, Y G

2015-01-01

Tetrahydrozoline has been introduced as new gingival retraction agent but its clinical efficacy with widely used conventional retraction agents has not been tested. The study was designed to clinically evaluate efficacy of newer retraction agent tetrahydrozoline with two widely used retraction systems i.e., Expasyl retraction system and medicated retraction cords on basis of amount of gingival retraction. 30 subjects were selected according to inclusion and exclusion criteria. Maxillary Impressions were made with irreversible hydrocolloid for all subjects. Tray material was used for making the special tray. Latin Block Design was Used in the Study to avoid tissue fatigue. Retraction was done with aluminium chloride; Tetrahydrozoline and Expasyl according to Latin block design. Impressions were poured with die stone. Casts were retrieved and sections were made with die cutter. 3 mm thin slices were obtained. Each slice was used to measure the amount of retraction under stereomicroscope under 20x and images were transferred to image analyser. The amount of gingival retraction obtained by using aluminium chloride as gingival retraction agent was maximum (148238.33 μm(2)) compared to tetrahydrozoline (140737.87 μm(2)) and Expasyl (67784.90 μm(2)).

A novel breast software phantom for biomechanical modeling of elastography.

PubMed

Bhatti, Syeda Naema; Sridhar-Keralapura, Mallika

2012-04-01

In developing breast imaging technologies, testing is done with phantoms. Physical phantoms are normally used but their size, shape, composition, and detail cannot be modified readily. These difficulties can be avoided by creating a software breast phantom. Researchers have created software breast phantoms using geometric and/or mathematical methods for applications like image fusion. The authors report a 3D software breast phantom that was built using a mechanical design tool, to investigate the biomechanics of elastography using finite element modeling (FEM). The authors propose this phantom as an intermediate assessment tool for elastography simulation; for use after testing with commonly used phantoms and before clinical testing. The authors design the phantom to be flexible in both, the breast geometry and biomechanical parameters, to make it a useful tool for elastography simulation. The authors develop the 3D software phantom using a mechanical design tool based on illustrations of normal breast anatomy. The software phantom does not use geometric primitives or imaging data. The authors discuss how to create this phantom and how to modify it. The authors demonstrate a typical elastography experiment of applying a static stress to the top surface of the breast just above a simulated tumor and calculate normal strains in 3D and in 2D with plane strain approximations with linear solvers. In particular, they investigate contrast transfer efficiency (CTE) by designing a parametric study based on location, shape, and stiffness of simulated tumors. The authors also compare their findings to a commonly used elastography phantom. The 3D breast software phantom is flexible in shape, size, and location of tumors, glandular to fatty content, and the ductal structure. Residual modulus, maps, and profiles, served as a guide to optimize meshing of this geometrically nonlinear phantom for biomechanical modeling of elastography. At best, low residues (around 1-5 KPa) were found within the phantom while errors were elevated (around 10-30 KPa) at tumor and lobule boundaries. From our FEM analysis, the breast phantom generated a superior CTE in both 2D and in 3D over the block phantom. It also showed differences in CTE values and strain contrast for deep and shallow tumors and showed significant change in CTE when 3D modeling was used. These changes were not significant in the block phantom. Both phantoms, however, showed worsened CTE values for increased input tumor-background modulus contrast. Block phantoms serve as a starting tool but a next level phantom, like the proposed breast phantom, will serve as a valuable intermediate for elastography simulation before clinical testing. Further, given the CTE metrics for the breast phantom are superior to the block phantom, and vary for tumor shape, location, and stiffness, these phantoms would enhance the study of elastography contrast. Further, the use of 2D phantoms with plane strain approximations overestimates the CTE value when compared to the true CTE achieved with 3D models. Thus, the use of 3D phantoms, like the breast phantom, with no approximations, will assist in more accurate estimation of modulus, especially valuable for 3D elastography systems.

Manipulating the ABCs of self-assembly via low-χ block polymer design

PubMed Central

Chang, Alice B.; Lee, Byeongdu; Garland, Carol M.; Jones, Simon C.; Matsen, Mark W.

2017-01-01

Block polymer self-assembly typically translates molecular chain connectivity into mesoscale structure by exploiting incompatible blocks with large interaction parameters (χij). In this article, we demonstrate that the converse approach, encoding low-χ interactions in ABC bottlebrush triblock terpolymers (χAC ≲ 0), promotes organization into a unique mixed-domain lamellar morphology, which we designate LAMP. Transmission electron microscopy indicates that LAMP exhibits ACBC domain connectivity, in contrast to conventional three-domain lamellae (LAM3) with ABCB periods. Complementary small-angle X-ray scattering experiments reveal a strongly decreasing domain spacing with increasing total molar mass. Self-consistent field theory reinforces these observations and predicts that LAMP is thermodynamically stable below a critical χAC, above which LAM3 emerges. Both experiments and theory expose close analogies to ABA′ triblock copolymer phase behavior, collectively suggesting that low-χ interactions between chemically similar or distinct blocks intimately influence self-assembly. These conclusions provide fresh opportunities for block polymer design with potential consequences spanning all self-assembling soft materials. PMID:28588139

Test Equality between Three Treatments under an Incomplete Block Crossover Design.

PubMed

Lui, Kung-Jong

2015-01-01

Under a random effects linear additive risk model, we compare two experimental treatments with a placebo in continuous data under an incomplete block crossover trial. We develop three test procedures for simultaneously testing equality between two experimental treatments and a placebo, as well as interval estimators for the mean difference between treatments. We apply Monte Carlo simulations to evaluate the performance of these test procedures and interval estimators in a variety of situations. We note that the bivariate test procedure accounting for the dependence structure based on the F-test is preferable to the other two procedures when there is only one of the two experimental treatments has a non-zero effect vs. the placebo. We note further that when the effects of the two experimental treatments vs. a placebo are in the same relative directions and are approximately of equal magnitude, the summary test procedure based on a simple average of two weighted-least-squares (WLS) estimators can outperform the other two procedures with respect to power. When one of the two experimental treatments has a relatively large effect vs. the placebo, the univariate test procedure with using Bonferroni's equality can be still of use. Finally, we use the data about the forced expiratory volume in 1 s (FEV1) readings taken from a double-blind crossover trial comparing two different doses of formoterol with a placebo to illustrate the use of test procedures and interval estimators proposed here.

Etoposide; colchicine; mitomycin C and cyclophosphamide tested in the in vitro mammalian cell micronucleus test (MNvit) in Chinese hamster lung (CHL) cells at Covance laboratories; Harrogate UK in support of OECD draft Test Guideline 487.

PubMed

Fowler, Paul; Whitwell, James; Jeffrey, Laura; Young, Jamie; Smith, Katie; Kirkland, David

2010-10-29

The following genotoxic chemicals were tested in the in vitro micronucleus assay, at Covance Laboratories, Harrogate, UK in the Chinese hamster lung cell line CHL. Etoposide (a topoisomerase inhibitor), colchicine (an aneugen), mitomycin C (a DNA cross linking agent) and cyclophosphamide (an alkylating agent requiring metabolic activation) were treated with and without cytokinesis block (by addition of cytochalasin B). This work formed part of a collaborative evaluation of the toxicity measures recommended in the draft OECD Test Guideline 487 for the in vitro micronucleus test. The toxicity measures used, detecting both cytostasis and cell death, were relative population doubling, relative increase in cell counts and relative cell counts for treatments in the absence of cytokinesis block, and replication index or cytokinesis blocked proliferation index in the presence of cytokinesis block. All of the chemicals tested gave significant increases in the percentage of micronucleated cells with and without cytokinesis block at concentrations giving approximately 60% toxicity (cytostasis and cell death) or less by all of the toxicity measures used. The outcomes from this series of tests support the use of relative increase in cell counts and relative population doubling, as well as relative cell counts, as appropriate measures of cytotoxicity for the non-cytokinesis blocked in vitro micronucleus assay. Copyright © 2010 Elsevier B.V. All rights reserved.

Cadmium chloride, benzo[a]pyrene and cyclophosphamide tested in the in vitro mammalian cell micronucleus test (MNvit) in the human lymphoblastoid cell line TK6 at Covance laboratories, Harrogate UK in support of OECD draft Test Guideline 487.

PubMed

Fowler, Paul; Whitwell, James; Jeffrey, Laura; Young, Jamie; Smith, Katie; Kirkland, David

2010-10-29

The following genotoxic chemicals were tested in the in vitro micronucleus assay, at Covance Laboratories, Harrogate, UK in the human lymphoblastoid cell line TK6. Cadmium chloride (an inorganic carcinogen), benzo[a]pyrene (a polycyclic aromatic hydrocarbon requiring metabolic activation) and cyclophosphamide (an alkylating agent requiring metabolic activation) were treated with and without cytokinesis block (by addition of cytochalasin B). This work formed part of a collaborative evaluation of the toxicity measures recommended in the draft OECD Test Guideline 487 for the in vitro micronucleus test. The toxicity measures used, capable of detecting both cytostasis and cell death, were relative population doubling, relative increase in cell counts and relative cell counts for treatments in the absence of cytokinesis block, and replication index or cytokinesis blocked proliferation index in the presence of cytokinesis block. All of the chemicals tested gave significant increases in the percentage of micronucleated cells with and without cytokinesis block at concentrations giving approximately 60% toxicity (cytostasis and cell death) or less by all of the toxicity measures used. The outcomes from this series of tests support the use of relative increase in cell counts and relative population doubling, as well as relative cell counts, as appropriate measures of cytotoxicity for the non-cytokinesis blocked in the in vitro micronucleus assay. Copyright © 2010 Elsevier B.V. All rights reserved.

Statistical evaluation of metal fill widths for emulated metal fill in parasitic extraction methodology

NASA Astrophysics Data System (ADS)

J-Me, Teh; Noh, Norlaili Mohd.; Aziz, Zalina Abdul

2015-05-01

In the chip industry today, the key goal of a chip development organization is to develop and market chips within a short time frame to gain foothold on market share. This paper proposes a design flow around the area of parasitic extraction to improve the design cycle time. The proposed design flow utilizes the usage of metal fill emulation as opposed to the current flow which performs metal fill insertion directly. By replacing metal fill structures with an emulation methodology in earlier iterations of the design flow, this is targeted to help reduce runtime in fill insertion stage. Statistical design of experiments methodology utilizing the randomized complete block design was used to select an appropriate emulated metal fill width to improve emulation accuracy. The experiment was conducted on test cases of different sizes, ranging from 1000 gates to 21000 gates. The metal width was varied from 1 x minimum metal width to 6 x minimum metal width. Two-way analysis of variance and Fisher's least significant difference test were used to analyze the interconnect net capacitance values of the different test cases. This paper presents the results of the statistical analysis for the 45 nm process technology. The recommended emulated metal fill width was found to be 4 x the minimum metal width.

Composite Interval Mapping Based on Lattice Design for Error Control May Increase Power of Quantitative Trait Locus Detection.

PubMed

He, Jianbo; Li, Jijie; Huang, Zhongwen; Zhao, Tuanjie; Xing, Guangnan; Gai, Junyi; Guan, Rongzhan

2015-01-01

Experimental error control is very important in quantitative trait locus (QTL) mapping. Although numerous statistical methods have been developed for QTL mapping, a QTL detection model based on an appropriate experimental design that emphasizes error control has not been developed. Lattice design is very suitable for experiments with large sample sizes, which is usually required for accurate mapping of quantitative traits. However, the lack of a QTL mapping method based on lattice design dictates that the arithmetic mean or adjusted mean of each line of observations in the lattice design had to be used as a response variable, resulting in low QTL detection power. As an improvement, we developed a QTL mapping method termed composite interval mapping based on lattice design (CIMLD). In the lattice design, experimental errors are decomposed into random errors and block-within-replication errors. Four levels of block-within-replication errors were simulated to show the power of QTL detection under different error controls. The simulation results showed that the arithmetic mean method, which is equivalent to a method under random complete block design (RCBD), was very sensitive to the size of the block variance and with the increase of block variance, the power of QTL detection decreased from 51.3% to 9.4%. In contrast to the RCBD method, the power of CIMLD and the adjusted mean method did not change for different block variances. The CIMLD method showed 1.2- to 7.6-fold higher power of QTL detection than the arithmetic or adjusted mean methods. Our proposed method was applied to real soybean (Glycine max) data as an example and 10 QTLs for biomass were identified that explained 65.87% of the phenotypic variation, while only three and two QTLs were identified by arithmetic and adjusted mean methods, respectively.

75 FR 12000 - Unblocking of Specially Designated Nationals and Blocked Persons Pursuant to the Cuban Assets...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... unblocking and removal from the list of Specially Designated Nationals and Blocked Persons (``SDN list'') of...-hour fax-on-demand service at (202) 622-0077. Background On March 2, 2010, OFAC removed from the SDN...

Design and installation of a subsea multiwell drilling template at Garden Banks Block 189

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domangue, R.J.

1991-09-01

This paper describes the economics, design, and installation of a simple drilling template that was used to retain or save subsea exploratory and delineation wells in Garden Banks Block 189 (GB 189) in the Gulf of Mexico.

Preparation and Testing of Corrosion and Spallation-Resistant Coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurley, John

2015-11-01

This Energy & Environmental Research Center (EERC) project is designed to determine if plating APMT®, a specific highly oxidation-resistant oxide dispersion-strengthened FeCrAl alloy made by Kanthal, onto nickel-based superalloy turbine parts is a viable method for substantially improving the lifetimes and maximum use temperatures of the parts. The method for joining the APMT plate to the superalloys is called evaporative metal bonding and involves placing a thin foil of zinc between the plate and the superalloy, clamping them together, and heating in an atmosphere-controlled furnace. Upon heating, the zinc melts and dissolves the oxide skins of the alloys at themore » bond line, allowing the two alloys to diffuse into each other. The zinc then diffuses through the alloys and evaporates from their surfaces. During this annual reporting period, the finite element model was completed and used to design clamping jigs to hold the APMT plate to the larger blocks of superalloys during the bonding process. The clamping system was machined from titanium–zirconium–molybdenum and used to bond the APMT plate to the superalloy blocks. The bond between the APMT plate was weak for one of each of the superalloy blocks. We believe that this occurred because enough oxidation had occurred on the surface of the parts as a result of a 1-month time period between sandblasting to prepare the parts and the actual bonding process. The other blocks were, therefore, bonded within 1 day of preparing the parts for bonding, and their joints appear strong. Scanning electron microscopy analyses of representative joints showed that no zinc remained in the alloys after bonding. Also, phases rich in hafnium and tantalum had precipitated near the bond line in the APMT. Iron from the APMT had diffused into the superalloys during bonding, more extensively in the CM247LC than in the Rene 80. Nickel from the superalloys had diffused into the APMT, again more extensively in the joint with the CM247LC than with the Rene 80. One-inch-diameter buttons were machined from each of the bonded blocks and sent to Siemens for standard oxidation, spallation, and corrosion testing, which should be complete in the spring of 2016.« less

A role of nucleus accumbens dopamine receptors in the nucleus accumbens core, but not shell, in fear prediction error.

PubMed

Li, Susan S Y; McNally, Gavan P

2015-08-01

Two experiments used an associative blocking design to study the role of dopamine receptors in the nucleus accumbens shell (AcbSh) and core (AcbC) in fear prediction error. Rats in the experimental groups were trained to a visual fear-conditioned stimulus (conditional stimulus [CS]) A in Stage I, whereas rats in the control groups were not. In Stage II, all rats received compound fear conditioning of the visual CSA and an auditory CSB. Rats were later tested for their fear responses to CSB. All rats received microinjections of saline or the D1-D2 receptor antagonist cis-(z)-flupenthixol prior to Stage II. These microinjections targeted either the AcbSh (Experiment 1) or the AcbC (Experiment 2). In each experiment, Stage I fear conditioning of CSA blocked fear learning to CSB. Microinjection of cis-(z)-flupenthixol (10 or 20 μg) into the AcbSh (Experiment 1) had no effect on fear learning or associative blocking. In contrast, microinjection of cis-(z)-flupenthixol (10 or 20 μg) into the AcbC (Experiment 2) attenuated blocking and so enabled fear learning to CSB. These results identify the AcbC as the critical locus for dopamine receptor contributions to fear prediction error and the associative blocking of fear learning. (c) 2015 APA, all rights reserved).

Phased array inspection of large size forged steel parts

NASA Astrophysics Data System (ADS)

Dupont-Marillia, Frederic; Jahazi, Mohammad; Belanger, Pierre

2018-04-01

High strength forged steel requires uncompromising quality to warrant advance performance for numerous critical applications. Ultrasonic inspection is commonly used in nondestructive testing to detect cracks and other defects. In steel blocks of relatively small dimensions (at least two directions not exceeding a few centimetres), phased array inspection is a trusted method to generate images of the inside of the blocks and therefore identify and size defects. However, casting of large size forged ingots introduces changes of mechanical parameters such as grain size, the Young's modulus, the Poisson's ratio, and the chemical composition. These heterogeneities affect the wave propagation, and consequently, the reliability of ultrasonic inspection and the imaging capabilities for these blocks. In this context, a custom phased array transducer designed for a 40-ton bainitic forged ingot was investigated. Following a previous study that provided local mechanical parameters for a similar block, two-dimensional simulations were made to compute the optimal transducer parameters including the pitch, width and number of elements. It appeared that depending on the number of elements, backwall reconstruction can generate high amplitude artefacts. Indeed, the large dimensions of the simulated block introduce numerous constructive interferences from backwall reflections which may lead to important artefacts. To increase image quality, the reconstruction algorithm was adapted and promising results were observed and compared with the scattering cone filter method available in the CIVA software.

Adiabatic quantum-flux-parametron cell library adopting minimalist design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takeuchi, Naoki, E-mail: takeuchi-naoki-kx@ynu.jp; Yamanashi, Yuki; Yoshikawa, Nobuyuki

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells inmore » the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.« less

Adiabatic quantum-flux-parametron cell library adopting minimalist design

NASA Astrophysics Data System (ADS)

Takeuchi, Naoki; Yamanashi, Yuki; Yoshikawa, Nobuyuki

2015-05-01

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells in the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.

Learning Effects in the Block Design Task: A Stimulus Parameter-Based Approach

ERIC Educational Resources Information Center

Miller, Joseph C.; Ruthig, Joelle C.; Bradley, April R.; Wise, Richard A.; Pedersen, Heather A.; Ellison, Jo M.

2009-01-01

Learning effects were assessed for the block design (BD) task, on the basis of variation in 2 stimulus parameters: perceptual cohesiveness (PC) and set size uncertainty (U). Thirty-one nonclinical undergraduate students (19 female) each completed 3 designs for each of 4 varied sets of the stimulus parameters (high-PC/high-U, high-PC/low-U,…

Synthetic polycations with controlled charge density and molecular weight as building blocks for biomaterials.

PubMed

Kleinberger, Rachelle M; Burke, Nicholas A D; Zhou, Christal; Stöver, Harald D H

2016-01-01

A series of polycations prepared by RAFT copolymerization of N-(3-aminopropyl)methacrylamide hydrochloride (APM) and N-(2-hydroxypropyl)methacrylamide, with molecular weights of 15 and 40 kDa, and APM content of 10-75 mol%, were tested as building blocks for electrostatically assembled hydrogels such as those used for cell encapsulation. Complexation and distribution of these copolymers within anionic calcium alginate gels, as well as cytotoxicity, cell attachment, and cell proliferation on surfaces grafted with the copolymers were found to depend on composition and molecular weight. Copolymers with lower cationic charge density and lower molecular weight showed less cytotoxicity and cell adhesion, and were more mobile within alginate gels. These findings aid in designing improved polyelectrolyte complexes for use as biomaterials.

Effects of the amount and composition of the forest floor on emergence and early establishment of loblolly pine seedlings

Treesearch

Michael G. Shelton

1995-01-01

Five forest floor weights (0, 10, 20, 30, and 40 MgJha), three forest floor compositions (pine, pine-hardwood, and hardwood), and two seed placements (forest floor and soil surface) were tested in a three-factorial. split-plot design with four incomplete, randomized blocks. The experiment was conducted in a nursery setting and used wooden frames to define 0.145-m

CFD validation experiments for hypersonic flows

NASA Technical Reports Server (NTRS)

Marvin, Joseph G.

1992-01-01

A roadmap for CFD code validation is introduced. The elements of the roadmap are consistent with air-breathing vehicle design requirements and related to the important flow path components: forebody, inlet, combustor, and nozzle. Building block and benchmark validation experiments are identified along with their test conditions and measurements. Based on an evaluation criteria, recommendations for an initial CFD validation data base are given and gaps identified where future experiments could provide new validation data.

Solid State Mini-RPV Color Imaging System

DTIC Science & Technology

1975-09-12

completed in the design and construction phase . Con- siderations are now in progress for conducting field tests of the equipment against "real world...Simplified Parallel Injection Configuration 2-21 CID Parallel Injection Configuration 2-23 Element Rate Timing 2-25 Horizontal Input and Phase Line...Timing 2-26 Line Reset /Injection Timing 2-27 Line Rate Timing (Start of Readout) 2-28 Driver A4 Block Diagram 2-31 Element Scan Time Base

Development of Understory Vegetation in Pine and Pine-Hardwood Shelterwood Stands in the Ouachita Mountains-the First 3 Years

Treesearch

Michael G. Shelton

1997-01-01

The shelterwood reproduction cutting method using two overstory compositions (a pine basal area of 30 ft* per acre with and without 15 ft’ per acre of hardwoods) and two methods of submerchantable hardwood control (chain-saw felling with and without stump-applied herbicide) was tested in a 2x2 factorial, split-plot design with four randomized complete blocks....

Navy Shipbuilding: Significant Investments in the Littoral Combat Ship Continue Amid Substantial Unknowns about Capabilities, Use, and Cost

DTIC Science & Technology

2013-07-01

composed of vice admirals from the requirements, acquisition, and fleet communities, and has the mission of ensuring “the successful procurement...development, manning, training, sustainment, and operational employment” of the LCS, mission packages, and shore 4The LCS block buy contracts include fixed...capabilities, limitations, and safety issues to help reduce design and programmatic risks. Operational testing is intended to assess a weapon system’s

A Polyamine Oxidizing Enzyme as a Drug to Treat Breast Cancer

DTIC Science & Technology

2008-07-01

construed as an official Department of the Army position , policy or decision unless so designated by other documentation. REPORT DOCUMENTATION...polysac- charides. The polysaccharides are required for SAO to act a vascular adhesion protein-1 ( VAP -1) (6). If the polysaccharides are not block on...SAO, when injected into the blood of test mice, it may interfere with the endogenous VAP -1. In addition, a low-level PEGylation probably will not

Identifying Effective Design Approaches to Allocate Genotypes in Two-Phase Designs: A Case Study in Pelargonium zonale

PubMed Central

Molenaar, Heike; Boehm, Robert; Piepho, Hans-Peter

2018-01-01

Robust phenotypic data allow adequate statistical analysis and are crucial for any breeding purpose. Such data is obtained from experiments laid out to best control local variation. Additionally, experiments frequently involve two phases, each contributing environmental sources of variation. For example, in a former experiment we conducted to evaluate production related traits in Pelargonium zonale, there were two consecutive phases, each performed in a different greenhouse. Phase one involved the propagation of the breeding strains to obtain the stem cutting count, and phase two involved the assessment of root formation. The evaluation of the former study raised questions regarding options for improving the experimental layout: (i) Is there a disadvantage to using exactly the same design in both phases? (ii) Instead of generating a separate layout for each phase, can the design be optimized across both phases, such that the mean variance of a pair-wise treatment difference (MVD) can be decreased? To answer these questions, alternative approaches were explored to generate two-phase designs either in phase-wise order (Option 1) or across phases (Option 2). In Option 1 we considered the scenarios (i) using in both phases the same experimental design and (ii) randomizing each phase separately. In Option 2, we considered the scenarios (iii) generating a single design with eight replicates and splitting these among the two phases, (iv) separating the block structure across phases by dummy coding, and (v) design generation with optimal alignment of block units in the two phases. In both options, we considered the same or different block structures in each phase. The designs were evaluated by the MVD obtained by the intra-block analysis and the joint inter-block–intra-block analysis. The smallest MVD was most frequently obtained for designs generated across phases rather than for each phase separately, in particular when both phases of the design were separated with a single pseudo-level. The joint optimization ensured that treatment concurrences were equally balanced across pairs, one of the prerequisites for an efficient design. The proposed alternative approaches can be implemented with any model-based design packages with facilities to formulate linear models for treatment and block structures. PMID:29354145

Phrenic nerve block caused by interscalene brachial plexus block: breathing effects of different sites of injection.

PubMed

Bergmann, Lars; Martini, Stefan; Kesselmeier, Miriam; Armbruster, Wolf; Notheisen, Thomas; Adamzik, Michael; Eichholz, Rϋdiger

2016-07-29

Interscalene brachial plexus (ISB) block is often associated with phrenic nerve block and diaphragmatic paresis. The goal of our study was to test if the anterior or the posterior ultrasound guided approach of the ISB is associated with a lower incidence of phrenic nerve blocks and impaired lung function. This was a prospective, randomized and single-blinded study of 84 patients scheduled for elective shoulder surgery who fullfilled the inclusion and exclusion critereria. Patients were randomized in two groups to receive either the anterior (n = 42) or the posterior (n = 42) approach for ISB. Clinical data were recorded. In both groups patients received ISB with a total injection volume of 15 ml of ropivacaine 1 %. Spirometry was conducted at baseline (T0) and 30 min (T30) after accomplishing the block. Changes in spirometrical variables between T0 and T30 were investigated by Wilcoxon signed-rank test for each puncture approach. The temporal difference between the posterior and the anterior puncture approach groups were again analyzed by the Wilcoxon-Mann-Whitney test. The spirometric results showed a significant decrease in vital capacity, forced expiratory volume per second, and maximum nasal inspiratory breathing after the Interscalene brachial plexus block; indicating a phrenic nerve block (p <0.001, Wilcoxon signed-rank). A significant difference in the development of the spirometric parameters between the anterior and the posterior group could not be identified (Wilcoxon-Mann-Whitney test). Despite the changes in spirometry, no cases of dyspnea were reported. A different site of injection (anterior or posterior) did not show an effect in reducing the cervical block spread of the local anesthetic and the incidence of phrenic nerve blocks during during ultrasound guided Interscalene brachial plexus block. Clinical breathing effects of phrenic nerve blocks are, however, usually well compensated, and subjective dyspnea did not occur in our patients. German Clinical Trials Register (DRKS number 00009908 , registered 26 January 2016).

Using Blocked Fractional Factorial Designs to Construct Discrete Choice Experiments for Health Care Studies

PubMed Central

Jaynes, Jessica; Wong, Weng Kee; Xu, Hongquan

2016-01-01

Discrete choice experiments (DCEs) are increasingly used for studying and quantifying subjects preferences in a wide variety of health care applications. They provide a rich source of data to assess real-life decision making processes, which involve trade-offs between desirable characteristics pertaining to health and health care, and identification of key attributes affecting health care. The choice of the design for a DCE is critical because it determines which attributes’ effects and their interactions are identifiable. We apply blocked fractional factorial designs to construct DCEs and address some identification issues by utilizing the known structure of blocked fractional factorial designs. Our design techniques can be applied to several situations including DCEs where attributes have different number of levels. We demonstrate our design methodology using two health care studies to evaluate (1) asthma patients’ preferences for symptom-based outcome measures, and (2) patient preference for breast screening services. PMID:26823156

Pattern-based IP block detection, verification, and variability analysis

NASA Astrophysics Data System (ADS)

Ahmad Ibrahim, Muhamad Asraf Bin; Muhsain, Mohamad Fahmi Bin; Kamal Baharin, Ezni Aznida Binti; Sweis, Jason; Lai, Ya-Chieh; Hurat, Philippe

2018-03-01

The goal of a foundry partner is to deliver high quality silicon product to its customers on time. There is an assumed trust that the silicon will yield, function and perform as expected when the design fits all the sign-off criteria. The use of Intellectual Property (IP) blocks is very common today and provides the customer with pre-qualified and optimized functions for their design thus shortening the design cycle. There are many methods by which an IP Block can be generated and placed within layout. Even with the most careful methods and following of guidelines comes the responsibility of sign-off checking. A foundry needs to detect where these IP Blocks have been placed and look for any violations. This includes DRC clean modifications to the IP Block which may or may not be intentional. Using a pattern-based approach to detect all IP Blocks used provides the foundry advanced capabilities to analyze them further for any kind of changes which could void the OPC and process window optimizations. Having any changes in an IP Block could cause functionality changes or even failures. This also opens the foundry to legal and cost issues while at the same time forcing re-spins of the design. In this publication, we discuss the methodology we have employed to avoid process issues and tape-out errors while at the same time reduce our manual work and improve the turnaround time. We are also able to use our pattern analysis to improve our OPC optimizations when modifications are encountered which have not been seen before.

Factor structure of the Hooper Visual Organization Test: a cross-cultural replication and extension.

PubMed

Merten, Thomas

2005-01-01

To investigate construct validity of the Hooper Visual Organization Test (VOT), a principal-axis analysis was performed on the neuropsychological test results of 200 German-speaking neurological patients who received a comprehensive battery, encompassing tests of visuospatial functions, memory, attention, executive functions, naming ability, and vocabulary. A four-factor solution was obtained with substantial loadings of the VOT only on the first factor, interpreted as a global dimension of non-verbal cognitive functions. This factor loaded significantly on numerous measures of visuospatial processing and attention (with particularly high loadings on WAIS-R Block Design, Trails A and B, and Raven's Standard Progressive Matrices). The remaining three factors were interpreted as memory, verbal abilities (vocabulary), and a separate factor of naming abilities.

An IO block array in a radiation-hardened SOI SRAM-based FPGA

NASA Astrophysics Data System (ADS)

Yan, Zhao; Lihua, Wu; Xiaowei, Han; Yan, Li; Qianli, Zhang; Liang, Chen; Guoquan, Zhang; Jianzhong, Li; Bo, Yang; Jiantou, Gao; Jian, Wang; Ming, Li; Guizhai, Liu; Feng, Zhang; Xufeng, Guo; Kai, Zhao; Chen, Stanley L.; Fang, Yu; Zhongli, Liu

2012-01-01

We present an input/output block (IOB) array used in the radiation-hardened SRAM-based field-programmable gate array (FPGA) VS1000, which is designed and fabricated with a 0.5 μm partially depleted silicon-on-insulator (SOI) logic process at the CETC 58th Institute. Corresponding with the characteristics of the FPGA, each IOB includes a local routing pool and two IO cells composed of a signal path circuit, configurable input/output buffers and an ESD protection network. A boundary-scan path circuit can be used between the programmable buffers and the input/output circuit or as a transparent circuit when the IOB is applied in different modes. Programmable IO buffers can be used at TTL/CMOS standard levels. The local routing pool enhances the flexibility and routability of the connection between the IOB array and the core logic. Radiation-hardened designs, including A-type and H-type body-tied transistors and special D-type registers, improve the anti-radiation performance. The ESD protection network, which provides a high-impulse discharge path on a pad, prevents the breakdown of the core logic caused by the immense current. These design strategies facilitate the design of FPGAs with different capacities or architectures to form a series of FPGAs. The functionality and performance of the IOB array is proved after a functional test. The radiation test indicates that the proposed VS1000 chip with an IOB array has a total dose tolerance of 100 krad(Si), a dose survivability rate of 1.5 × 1011 rad(Si)/s, and a neutron fluence immunity of 1 × 1014 n/cm2.

E1-09 Termite Choice Testing: What is it good for?

Treesearch

Frederick III Green; Patti Lebow; S. Nami Kartal

2014-01-01

The prime objective of this investigation was to compare mass loss from termite attack on NHA treated and untreated pine blocks simultaneously in a two-block choice test using Reticulitermes flavipes (Kollar). Southern pine blocks were vacuum treated with aqueous solutions of NHA ranging from 250-10,000 ppm and exposed to one gram of R....

Solid oxide fuel cell matrix and modules

DOEpatents

Riley, Brian

1990-01-01

Porous refractory ceramic blocks arranged in an abutting, stacked configuration and forming a three dimensional array provide a support structure and coupling means for a plurality of solid oxide fuel cells (SOFCs). Each of the blocks includes a square center channel which forms a vertical shaft when the blocks are arranged in a stacked array. Positioned within the channel is a SOFC unit cell such that a plurality of such SOFC units disposed within a vertical shaft form a string of SOFC units coupled in series. A first pair of facing inner walls of each of the blocks each include an interconnecting channel hole cut horizontally and vertically into the block walls to form gas exit channels. A second pair of facing lateral walls of each block further include a pair of inner half circular grooves which form sleeves to accommodate anode fuel and cathode air tubes. The stack of ceramic blocks is self-supporting, with a plurality of such stacked arrays forming a matrix enclosed in an insulating refractory brick structure having an outer steel layer. The necessary connections for air, fuel, burnt gas, and anode and cathode connections are provided through the brick and steel outer shell. The ceramic blocks are so designed with respect to the strings of modules that by simple and logical design the strings could be replaced by hot reloading if one should fail. The hot reloading concept has not been included in any previous designs.

New Kids on the Block Schedule: Beginning Teachers Face Challenges

ERIC Educational Resources Information Center

Zepeda, Sally J.; Mayers, R. Stewart

2001-01-01

Across the United States, an ever-increasing number of high schools have reevaluated their use of instructional time and have adopted some form of a block schedule. Block scheduling, an innovation grounded in Trump's Flexible Modular Scheduling Design, reorganizes the school day into extended blocks of time, each approximately 70 to 90 minutes.…

77 FR 10808 - Designation of One Entity Pursuant to Executive Order 13572 of April 29, 2011, “Blocking Property...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-23

... Executive Order 13572 of April 29, 2011, ``Blocking Property of Certain Persons With Respect to Human Rights..., 2011, ``Blocking Property of Certain Persons with Respect to Human Rights Abuses in Syria.'' DATES: The..., ``Blocking Property of Certain Persons with Respect to Human Rights Abuses in Syria,'' (the ``Order...

76 FR 54534 - Designation of One Entity Pursuant to Executive Order 13572 of April 29, 2011, “Blocking Property...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-01

... Executive Order 13572 of April 29, 2011, ``Blocking Property of Certain Persons with Respect to Human Rights... April 29, 2011, ``Blocking Property of Certain Persons with Respect to Human Rights Abuses in Syria..., ``Blocking Property of Certain Persons with Respect to Human Rights Abuses in Syria,'' (the ``Order...

77 FR 20693 - Designation of Three Individuals Pursuant to Executive Order 13573 of May 18, 2011, “Blocking...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-05

... Pursuant to Executive Order 13573 of May 18, 2011, ``Blocking Property of Senior Officials of the... whose property and interests in property are blocked pursuant to Executive Order 13573 of May 18, 2011...-622-0077. Background On May 18, 2011, the President issued Executive Order 13573, ``Blocking Property...

Effects of a Multidisciplinary Approach to Improve Volume of Diagnostic Material in CT-Guided Lung Biopsies

PubMed Central

Ferguson, Philip E.; Sales, Catherine M.; Hodges, Dalton C.; Sales, Elizabeth W.

2015-01-01

Background Recent publications have emphasized the importance of a multidisciplinary strategy for maximum conservation and utilization of lung biopsy material for advanced testing, which may determine therapy. This paper quantifies the effect of a multidisciplinary strategy implemented to optimize and increase tissue volume in CT-guided transthoracic needle core lung biopsies. The strategy was three-pronged: (1) once there was confidence diagnostic tissue had been obtained and if safe for the patient, additional biopsy passes were performed to further increase volume of biopsy material, (2) biopsy material was placed in multiple cassettes for processing, and (3) all tissue ribbons were conserved when cutting blocks in the histology laboratory. This study quantifies the effects of strategies #1 and #2. Design This retrospective analysis comparing CT-guided lung biopsies from 2007 and 2012 (before and after multidisciplinary approach implementation) was performed at a single institution. Patient medical records were reviewed and main variables analyzed include biopsy sample size, radiologist, number of blocks submitted, diagnosis, and complications. The biopsy sample size measured was considered to be directly proportional to tissue volume in the block. Results Biopsy sample size increased 2.5 fold with the average total biopsy sample size increasing from 1.0 cm (0.9–1.1 cm) in 2007 to 2.5 cm (2.3–2.8 cm) in 2012 (P<0.0001). The improvement was statistically significant for each individual radiologist. During the same time, the rate of pneumothorax requiring chest tube placement decreased from 15% to 7% (P = 0.065). No other major complications were identified. The proportion of tumor within the biopsy material was similar at 28% (23%–33%) and 35% (30%–40%) for 2007 and 2012, respectively. The number of cases with at least two blocks available for testing increased from 10.7% to 96.4% (P<0.0001). Conclusions The effect of this multidisciplinary strategy to CT-guided lung biopsies was effective in significantly increasing tissue volume and number of blocks available for advanced diagnostic testing. PMID:26479367

Materials property definition and generation for carbon-carbon and carbon phenolic materials

NASA Technical Reports Server (NTRS)

Canfield, A. R.; Mathis, J. R.; Starrett, H. S.; Koenig, J. R.

1987-01-01

A data base program to generate statistically significant material-property data for carbon-carbon and carbon phenolic materials to be used in designs of Space Shuttle is described. The program, which will provide data necessary for thermal and stress modeling of Shuttle nozzle and exit cone structures, includes evaluation of tension, compression, shear strength, shear modulus, thermal expansion, thermal conductivity, permeability, and emittance for both materials; the testing of carbon phenolic materials also includes CTE, off-gassing, pyrolysis, and RTG. Materials to be tested will be excised from Space Shuttle inlet, throat, and exit cone billets and modified involute carbon-carbon exit cones; coprocessed blocks, panels, and cylinders will also be tested.

Broadband non-reciprocal transmission of sound with invariant frequency

PubMed Central

Gu, Zhong-ming; Hu, Jie; Liang, Bin; Zou, Xin-ye; Cheng, Jian-chun

2016-01-01

We design and experimentally demonstrate a broadband yet compact acoustic diode (AD) by using an acoustic nonlinear material and a pair of gain and lossy materials. Due to the capabilities of maintaining the original frequency and high forward transmission while blocking backscattered wave, our design is closer to the desired features of a perfect AD and is promising to play the essential diode-like role in realistic acoustic systems, such as ultrasound imaging, noise control and nondestructive testing. Furthermore, our design enables improving the sensitivity and the robustness of device simultaneously by tailoring an individual structural parameter. We envision our design will take a significant step towards the realization of applicable acoustic one-way devices, and inspire the research of non-reciprocal wave manipulation in other fields. PMID:26805712

Mechanical properties and internal fit of 4 CAD-CAM block materials.

PubMed

Goujat, Alexis; Abouelleil, Hazem; Colon, Pierre; Jeannin, Christophe; Pradelle, Nelly; Seux, Dominique; Grosgogeat, Brigitte

2018-03-01

Recent polymer-based computer-assisted design and computer-assisted manufacturing (CAD-CAM) materials have been commercialized for inlay restorations, a polymer-infiltrated ceramic-network (PICN) and composite resin nanoceramics. Little independent evidence regarding their mechanical properties exists. Internal adaptation is an important factor for the clinical success and longevity of a restoration, and data concerning this parameter for inlays made with these blocks are scarce. The purpose of this in vitro study was to evaluate and compare the mechanical properties (flexural strength, flexural modulus, Vickers hardness, fracture toughness) and the internal adaptation of these recent polymer-based blocks with a lithium disilicate glass-ceramic block. The materials tested in this study were a PICN material (Vita Enamic), 2 composite resin nanoceramics (Lava Ultimate; 3M ESPE and Cerasmart; GCDental Products), and a lithium disilicate glass-ceramic (IPS e.max CAD). Mechanical properties were evaluated according to ISO norm DIS 6872:2013. Bar-shaped specimens (18×3×3 mm) were prepared and submitted to a 3-point bend test using a universal testing machine at a cross-head speed of 0.5 mm/min. In addition, identical cavities were prepared in 60 human mandibular extracted molars (n=15) and optically scanned to receive mesioocclusodistal inlays milled with the 4 materials tested in a CEREC Inlab milling machine. The replica technique and a stereomicroscope (×20) were used to measure the internal fit of the inlays at 9 preselected locations. All data were statistically analyzed using 1-way ANOVA and the post hoc Tukey multiple comparison or Games-Howell test (α=.05). The mean flexural strength of the tested blocks ranged from 148.7 ±9.5 MPa (Vita Enamic) to 216.5 ±28.3 MPa (Cerasmart). The mean flexural modulus ranged from 23.3 ±6.4 GPa (Vita Enamic) to 52.8 ±10.5 GPa (IPS e.max CAD). The mean Vickers hardness ranged from 0.66 ±0.02 GPa (Cerasmart) to 5.98 ±0.69 GPa (IPS e.max CAD). The mean fracture toughness ranged from 1.2 ±0.17 MPa.m 1/2 (Cerasmart) to 1.8 ±0.29 MPa.m 1/2 (IPS e.max CAD). The values for internal discrepancy ranged from 119 ±55 μm to 234 ±51 μm. The mean internal discrepancy was significantly higher for Lava Ultimate (P<.05) than IPS e.max CAD and Cerasmart but not for Vita Enamic. The factor ''material'' was statistically significant in relation to the mechanical properties evaluated in this study (P<.05). The Pearson correlation was negative between the flexural strength results and the internal discrepancy of the materials tested (R 2 =0.941; P<.05). The mechanical properties of the CAD-CAM block materials tested were within the acceptable range for fabrication of single restorations according to the ISO standard for ceramics (ISO 6872:2008). IPS e.max CAD and Cerasmart were observed to have superior flexural strength and better internal fit. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Comparison of the Effect of Continuous Femoral Nerve Block and Adductor Canal Block after Primary Total Knee Arthroplasty.

PubMed

Seo, Seung Suk; Kim, Ok Gul; Seo, Jin Hyeok; Kim, Do Hoon; Kim, Youn Gu; Park, Beyoung Yun

2017-09-01

This study aimed to compare the effects of femoral nerve block and adductor canal block on postoperative pain, quadriceps strength, and walking ability after primary total knee arthroplasty. Between November 2014 and February 2015, 60 patients underwent primary total knee arthroplasty. Thirty patients received femoral nerve block and the other 30 received adductor canal block for postoperative pain control. Before spinal anesthesia, the patients received nerve block via a catheter (20 mL 0.75% ropivacaine was administered initially, followed by intermittent bolus injection of 10 mL 0.2% ropivacaine every 6 hours for 3 days). The catheters were maintained in the exact location of nerve block in 24 patients in the femoral nerve block group and in 19 patients in the adductor canal block group. Data collection was carried out from these 43 patients. To evaluate postoperative pain control, the numerical rating scale scores at rest and 45° flexion of the knee were recorded. To evaluate quadriceps strength, manual muscle testing was performed. Walking ability was assessed using the Timed Up and Go test. We also evaluated analgesic consumption and complications of peripheral nerve block. No significant intergroup difference was observed in the numerical rating scale scores at rest and 45° flexion of the knee on postoperative days 1, 2, 3, and 7. The adductor canal block group had significantly greater quadriceps strength than did the femoral nerve block group, as assessed by manual muscle testing on postoperative days 1, 2, and 3. The 2 groups showed no difference in walking ability on postoperative day 1, but on postoperative days 2, 3, walking ability was significantly better in the adductor canal block group than in the femoral nerve block group. No significant intergroup difference was observed in analgesic consumption. The groups showed no difference in postoperative pain control. Adductor canal block was superior to femoral nerve block in preserving quadriceps strength and walking ability. However, adductor canal block was inferior to femoral nerve block in maintaining the exact location of the catheter.

Evaluating OpenSHMEM Explicit Remote Memory Access Operations and Merged Requests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boehm, Swen; Pophale, Swaroop S; Gorentla Venkata, Manjunath

The OpenSHMEM Library Specification has evolved consid- erably since version 1.0. Recently, non-blocking implicit Remote Memory Access (RMA) operations were introduced in OpenSHMEM 1.3. These provide a way to achieve better overlap between communication and computation. However, the implicit non-blocking operations do not pro- vide a separate handle to track and complete the individual RMA opera- tions. They are guaranteed to be completed after either a shmem quiet(), shmem barrier() or a shmem barrier all() is called. These are global com- pletion and synchronization operations. Though this semantic is expected to achieve a higher message rate for the applications, themore » drawback is that it does not allow fine-grained control over the completion of RMA operations. In this paper, first, we introduce non-blocking RMA operations with requests, where each operation has an explicit request to track and com- plete the operation. Second, we introduce interfaces to merge multiple requests into a single request handle. The merged request tracks multiple user-selected RMA operations, which provides the flexibility of tracking related communication operations with one request handle. Lastly, we explore the implications in terms of performance, productivity, usability and the possibility of defining different patterns of communication via merging of requests. Our experimental results show that a well designed and implemented OpenSHMEM stack can hide the overhead of allocating and managing the requests. The latency of RMA operations with requests is similar to blocking and implicit non-blocking RMA operations. We test our implementation with the Scalable Synthetic Compact Applications (SSCA #1) benchmark and observe that using RMA operations with requests and merging of these requests outperform the implementation using blocking RMA operations and implicit non-blocking operations by 49% and 74% respectively.« less

Intravenous dexamethasone and perineural dexamethasone similarly prolong the duration of analgesia after supraclavicular brachial plexus block: a randomized, triple-arm, double-blind, placebo-controlled trial.

PubMed

Abdallah, Faraj W; Johnson, James; Chan, Vincent; Murgatroyd, Harry; Ghafari, Mohammad; Ami, Noam; Jin, Rongyu; Brull, Richard

2015-01-01

Perineural dexamethasone prolongs the duration of single-injection peripheral nerve block when added to the local anesthetic solution. Postulated systemic mechanisms of action along with theoretical safety concerns have prompted the investigation of intravenous dexamethasone as an alternative, with decidedly mixed results. We aimed to confirm that addition of intravenous dexamethasone will prolong the duration of analgesia after single-injection supraclavicular block compared with conventional long-acting local anesthetic alone or in combination with perineural dexamethasone for ambulatory upper extremity surgery. Seventy-five patients were randomized to receive supraclavicular block using 30-mL bupivacaine 0.5% alone (Control), with concomitant intravenous dexamethasone 8 mg (DexIV), or with perineural dexamethasone 8 mg (DexP). Duration of analgesia was designated as the primary outcome. To test our hypothesis, the superiority of DexIV was first compared with Control and then with DexP. Motor block duration, pain scores, opioid consumption, opioid-related side effects, patient satisfaction, and block-related complications were also analyzed. Twenty-five patients per group were analyzed. The duration of analgesia (mean [95% confidence interval]) was prolonged in the DexIV group(25 hours [17.6–32.4]) compared with Control (13.2 hours [11.5–15.0]; P < 0.001) but similar to the DexP group (25 hours[19.5–30.5]; P = 1). [corrected] Both DexIV and DexP had reduced pain scores, reduced postoperative opioid consumption, and improved satisfaction compared with Control. In a single-injection supraclavicular block with long-acting local anesthetic, the effectiveness of intravenous dexamethasone in prolonging the duration of analgesia seems similar to perineural dexamethasone.

78 FR 6179 - Unblocking of One Specially Designated National and Blocked Person Pursuant to Executive Order 13448

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-29

... Nationals and Blocked Persons (``SDN List'') of the individual identified in this notice whose property and... SDN List the individual listed below, whose property and interests in property were blocked pursuant...

Selecting the best design for nonstandard toxicology experiments.

PubMed

Webb, Jennifer M; Smucker, Byran J; Bailer, A John

2014-10-01

Although many experiments in environmental toxicology use standard statistical experimental designs, there are situations that arise where no such standard design is natural or applicable because of logistical constraints. For example, the layout of a laboratory may suggest that each shelf serve as a block, with the number of experimental units per shelf either greater than or less than the number of treatments in a way that precludes the use of a typical block design. In such cases, an effective and powerful alternative is to employ optimal experimental design principles, a strategy that produces designs with precise statistical estimates. Here, a D-optimal design was generated for an experiment in environmental toxicology that has 2 factors, 16 treatments, and constraints similar to those described above. After initial consideration of a randomized complete block design and an intuitive cyclic design, it was decided to compare a D-optimal design and a slightly more complicated version of the cyclic design. Simulations were conducted generating random responses under a variety of scenarios that reflect conditions motivated by a similar toxicology study, and the designs were evaluated via D-efficiency as well as by a power analysis. The cyclic design performed well compared to the D-optimal design. © 2014 SETAC.

Development of Test Article Building Block (TABB) for deployable platform systems

NASA Technical Reports Server (NTRS)

Greenberg, H. S.; Barbour, R. T.

1984-01-01

The concept of a Test Article Building Block (TABB) is described. The TABB is a ground test article that is representative of a future building block that can be used to construct LEO and GEO deployable space platforms for communications and scientific payloads. This building block contains a main housing within which the entire structure, utilities, and deployment/retraction mechanism are stowed during launch. The end adapter secures the foregoing components to the housing during launch. The main housing and adapter provide the necessary building-block-to-building-block attachments for automatically deployable platforms. Removal from the shuttle cargo bay can be accomplished with the remote manipulator system (RMS) and/or the handling and positioning aid (HAPA). In this concept, all the electrical connections are in place prior to launch with automatic latches for payload attachment provided on either the end adapters or housings. The housings also can contain orbiter docking ports for payload installation and maintenance.

Thinking Outside the Block: An Innovative Alternative to 4X4 Block Scheduling.

ERIC Educational Resources Information Center

Frank, Myra

2002-01-01

Introduces a 4x1 block scheduling method that was developed as an alternative to 4x4 block scheduling. Schedules Fridays for summer school, test preparation, and enrichment and elective courses. Includes suggestions on how to alleviate drawbacks of the 4x1 block schedule. (YDS)

Around Marshall

NASA Image and Video Library

1963-02-04

At its founding, the Marshall Space Flight Center (MSFC) inherited the Army’s Jupiter and Redstone test stands, but much larger facilities were needed for the giant stages of the Saturn V. From 1960 to 1964, the existing stands were remodeled and a sizable new test area was developed. The new comprehensive test complex for propulsion and structural dynamics was unique within the nation and the free world, and they remain so today because they were constructed with foresight to meet the future as well as on going needs. Construction of the S-IC Static test stand complex began in 1961 in the west test area of MSFC, and was completed in 1964. The S-IC static test stand was designed to develop and test the 138-ft long and 33-ft diameter Saturn V S-IC first stage, or booster stage, weighing in at 280,000 pounds. Required to hold down the brute force of a 7,500,000-pound thrust produced by 5 F-1 engines, the S-IC static test stand was designed and constructed with the strength of hundreds of tons of steel and 12,000,000 pounds of cement, planted down to bedrock 40 feet below ground level. The foundation walls, constructed with concrete and steel, are 4 feet thick. The base structure consists of four towers with 40-foot-thick walls extending upward 144 feet above ground level. The structure was topped by a crane with a 135-foot boom. With the boom in the upright position, the stand was given an overall height of 405 feet, placing it among the highest structures in Alabama at the time. In addition to the stand itself, related facilities were constructed during this time. Built directly east of the test stand was the Block House, which served as the control center for the test stand. The two were connected by a narrow access tunnel which housed the cables for the controls. This photograph taken February 4, 1963, gives an impressive look at the Block House looking directly through the ever-growing four towers of the S-IC Test Stand.

14 CFR 33.81 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.81 Applicability. This subpart prescribes the block tests and inspections for turbine engines. [Doc. 3025, 29 FR 7453, June 10, 1964, as...

14 CFR 33.81 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.81 Applicability. This subpart prescribes the block tests and inspections for turbine engines. [Doc. 3025, 29 FR 7453, June 10, 1964, as...

14 CFR 33.81 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.81 Applicability. This subpart prescribes the block tests and inspections for turbine engines. [Doc. 3025, 29 FR 7453, June 10, 1964, as...

Reversible Nerve Conduction Block Using Kilohertz Frequency Alternating Current

PubMed Central

Kilgore, Kevin L.; Bhadra, Niloy

2013-01-01

Objectives The features and clinical applications of balanced-charge kilohertz frequency alternating currents (KHFAC) are reviewed. Preclinical studies of KHFAC block have demonstrated that it can produce an extremely rapid and reversible block of nerve conduction. Recent systematic analysis and experimentation utilizing KHFAC block has resulted in a significant increase in interest in KHFAC block, both scientifically and clinically. Materials and Methods We review the history and characteristics of KHFAC block, the methods used to investigate this type of block, the experimental evaluation of block, and the electrical parameters and electrode designs needed to achieve successful block. We then analyze the existing clinical applications of high frequency currents, comparing the early results with the known features of KHFAC block. Results Although many features of KHFAC block have been characterized, there is still much that is unknown regarding the response of neural structures to rapidly fluctuating electrical fields. The clinical reports to date do not provide sufficient information to properly evaluate the mechanisms that result in successful or unsuccessful treatment. Conclusions KHFAC nerve block has significant potential as a means of controlling nerve activity for the purpose of treating disease. However, early clinical studies in the use of high frequency currents for the treatment of pain have not been designed to elucidate mechanisms or allow direct comparisons to preclinical data. We strongly encourage the careful reporting of the parameters utilized in these clinical studies, as well as the development of outcome measures that could illuminate the mechanisms of this modality. PMID:23924075

LADEE Satellite Modeling and Simulation Development

NASA Technical Reports Server (NTRS)

Adams, Michael; Cannon, Howard; Frost, Chad

2011-01-01

As human activity on and around the Moon increases, so does the likelihood that our actions will have an impact on its atmosphere. The Lunar Atmosphere and Dust Environment Explorer (LADEE), a NASA satellite scheduled to launch in 2013, will orbit the Moon collecting composition, density, and time variability data to characterize the current state of the lunar atmosphere. LADEE will also test the concept of the "Modular Common Bus" spacecraft architecture, an effort to reduce both development time and cost by designing reusable, modular components for use in multiple missions with similar requirements. An important aspect of this design strategy is to both simulate the spacecraft and develop the flight code in Simulink, a block diagram-style programming language that allows easy algorithm visualization and performance testing. Before flight code can be tested, however, a realistic simulation of the satellite and its dynamics must be generated and validated. This includes all of the satellite control system components such as actuators used for force and torque generation and sensors used for inertial orientation reference. My primary responsibilities have included designing, integrating, and testing models for the LADEE thrusters, reaction wheels, star trackers, and rate gyroscopes.

Solid rocket motor fire tests: Phases 1 and 2

NASA Astrophysics Data System (ADS)

Chang, Yale; Hunter, Lawrence W.; Han, David K.; Thomas, Michael E.; Cain, Russell P.; Lennon, Andrew M.

2002-01-01

JHU/APL conducted a series of open-air burns of small blocks (3 to 10 kg) of solid rocket motor (SRM) propellant at the Thiokol Elkton MD facility to elucidate the thermal environment under burning propellant. The propellant was TP-H-3340A for the STAR 48 motor, with a weight ratio of 71/18/11 for the ammonium perchlorate, aluminum, and HTPB binder. Combustion inhibitor applied on the blocks allowed burning on the bottom and/or sides only. Burns were conducted on sand and concrete to simulate near-launch pad surfaces, and on graphite to simulate a low-recession surface. Unique test fixturing allowed propellant self-levitation while constraining lateral motion. Optics instrumentation consisted of a longwave infrared imaging pyrometer, a midwave spectroradiometer, and a UV/visible spectroradiometer. In-situ instrumentation consisted of rod calorimeters, Gardon gauges, elevated thermocouples, flush thermocouples, a two-color pyrometer, and Knudsen cells. Witness materials consisted of yttria, ceria, alumina, tungsten, iridium, and platinum/rhodium. Objectives of the tests were to determine propellant burn characteristics such as burn rate and self-levitation, to determine heat fluxes and temperatures, and to carry out materials analyses. A summary of qualitative results: alumina coated almost all surfaces, the concrete spalled, sand moisture content matters, the propellant self-levitated, the test fixtures worked as designed, and bottom-burning propellant does not self-extinguish. A summary of quantitative results: burn rate averaged 1.15 mm/s, thermocouples peaked at 2070 C, pyrometer readings matched MWIR data at about 2400 C, the volume-averaged plume temperatures were 2300-2400 C with peaks of 2400-2600 C, and the heat fluxes peaked at 125 W/cm2. These results are higher than other researchers' measurements of top-burning propellant in chimneys, and will be used, along with Phase 3 test results, to analyze hardware response to these environments, including General Purpose Heat Sources (GPHS) and Radioisotope Heater Units (RHU). Follow-on Phase 3 tests burning propellant blocks up to 90 kg will be briefly described. .

31 CFR 515.306 - Specially designated national.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Foreign Assets Control's Specially Designated Nationals and Blocked Persons List (“SDN List”) for... interests in property therefore are blocked pursuant to this part. The SDN List entries for such persons include the identifier “[CUBA].” The SDN List is accessible through the following page on the Office of...

31 CFR 515.306 - Specially designated national.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Foreign Assets Control's Specially Designated Nationals and Blocked Persons List (“SDN List”) for... interests in property therefore are blocked pursuant to this part. The SDN List entries for such persons include the identifier “[CUBA].” The SDN List is accessible through the following page on the Office of...

31 CFR 515.306 - Specially designated national.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of Foreign Assets Control's Specially Designated Nationals and Blocked Persons List (“SDN List”) for... interests in property therefore are blocked pursuant to this part. The SDN List entries for such persons include the identifier “[CUBA].” The SDN List is accessible through the following page on the Office of...

31 CFR 515.306 - Specially designated national.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Foreign Assets Control's Specially Designated Nationals and Blocked Persons List (“SDN List”) for... interests in property therefore are blocked pursuant to this part. The SDN List entries for such persons include the identifier “[CUBA].” The SDN List is accessible through the following page on the Office of...

78 FR 28700 - Unblocking of Specially Designated Nationals and Blocked Persons Pursuant to the Foreign...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-15

... Secretary of Homeland Security when designating and blocking the property or interests in property, subject... financial or technological support for or to, or providing goods or services in support of, the..., Colombia; citizen Colombia; Cedula No. 79263544 (Colombia) (individual) [SDNTK]. 2. MORENO BERNAL, Luz...

Design of a doubly-hydrophilic block copolypeptide that directs the formation of calcium carbonate microspheres.

PubMed

Euliss, Larken E; Trnka, Tina M; Deming, Timothy J; Stucky, Galen D

2004-08-07

The crystallization of calcium carbonate into microspheres has been accomplished using the rationally-designed, doubly-hydrophilic block copolypeptide poly(Nepsilon-2[2-(2-methoxyethoxy)ethoxy]acetyl-L-lysine)(100)-b-poly(L-aspartate sodium salt)30 as a structure-directing agent.

Photo-responsive block copolymer micelles: design and behavior.

PubMed

Gohy, Jean-François; Zhao, Yue

2013-09-07

Stimuli-responsive block copolymer micelles are the topic of intense research since they are able to show sharp and eventually reversible responses to various environmental changes and find applications in various fields including controlled drug delivery. Among all the available stimuli, light has recently attracted much attention since it can be localized in time and space, and it can also be triggered from outside of the system. In this tutorial review, we highlight the progress realized in recent years. More precisely, we provide some guidelines towards the rational design of photo-responsive block copolymers and we present the different photo-responsive moieties that have been used so far. We also discuss the different types of irreversible and reversible responses encountered by photo-responsive block copolymer micelles. Finally, we suggest possible future developments including the design of biocompatible systems operating at excitation wavelengths compatible for biomedical applications.

Apollo Block I Spacesuit Development and Apollo Block II Spacesuit Competition

NASA Technical Reports Server (NTRS)

McBarron, Jim

2013-01-01

Jim McBarron has over 40 years of experience with the U.S. Air Force pressure suit and NASA spacesuit development and operations. As a result of his experience, he shared his significant knowledge about the requirements and modifications made to the Gemini spacesuit, which were necessary to support the Apollo Block I Program. In addition, he provided an overview of the Apollo Block II Spacesuit competition test program conducted by the NASA Manned Spacecraft Center. Topics covered included the program's chronology; competition test program ground rules, scoring details, and final test results; and the implementation of resulting modifications to the Apollo Spacesuit Program. He concluded his presentation by identifying noteworthy lessons learned.

Involvement of noradrenergic and corticoid receptors in the consolidation of the lasting anxiogenic effects of predator stress.

PubMed

Adamec, R; Muir, C; Grimes, M; Pearcey, K

2007-05-16

The roles of beta-NER (beta-noradrenergic receptor), GR (glucocorticoid) and mineral corticoid receptors (MR) in the consolidation of anxiogenic effects of predator stress were studied. One minute after predator stress, different groups of rats were injected (ip) with vehicle, propranolol (beta-NER blocker, 5 and 10 mg/kg), mifepristone (RU486, GR blocker, 20 mg/kg), spironolactone (MR blocker, 50 mg/kg), propranolol (5 mg/kg) plus RU486 (20 mg/kg) or the anxiolytic, chloradiazepoxide (CPZ, 10 mg/kg). One week later, rodent anxiety was assessed in elevated plus maze, hole board, light/dark box, social interaction and acoustic startle. Considering all tests except startle, propranolol dose dependently blocked consolidation of lasting anxiogenic effects of predator stress in all tests. GR receptor block alone was ineffective. However, GR block in combination with an ineffective dose of propranolol did blocked consolidation of predator stress effects in all tests, suggesting a synergism between beta-NER and GR. Surprisingly, MR block prevented consolidation of anxiogenic effects in all tests except the light/dark box. CPZ post stress was ineffective against the anxiogenic impact of predator stress. Study of startle was complicated by the fact that anxiogenic effects of stress on startle amplitude manifested as both an increase and a decrease in startle amplitude. Suppression of startle occurred in stressed plus vehicle injected groups handled three times prior to predator stress. In contrast, stressed plus vehicle rats handled five times prior to predator stress showed increases in startle, as did all predator stressed only groups. Mechanisms of consolidation of the different startle responses appear to differ. CPZ post stress blocked startle suppression but not enhancement of startle. Propranolol post stress had no effect on either suppression or enhancement of startle. GR block alone post stress prevented suppression of startle, but not enhancement. In contrast blocking GR and beta-NER together prevented startle enhancement. MR block also prevented startle enhancement. Effects of MR block on startle suppression were not tested. Delay of habituation to startle was found in all stressed rats. Consolidation of delay of habituation was blocked or attenuated by post stress MR block, GR plus beta-NER block and CPZ but not by post stress GR or beta-NER block alone. Taken together, present findings suggest consolidation of lasting anxiogenic effects of predator stress may share some of the same neurochemical mechanisms implicated in some forms of fear memory consolidation. Implications of these findings for the study of stress-induced changes in affect including posttraumatic stress disorder (PTSD) are discussed.

14 CFR 33.81 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.81 Applicability. This subpart prescribes the block tests and inspections for turbine engines. [Doc. No. 3025, 29 FR 7453, June 10, 1964, as...

Active angular alignment of gauge blocks in double-ended interferometers.

PubMed

Buchta, Zdeněk; Reřucha, Simon; Hucl, Václav; Cížek, Martin; Sarbort, Martin; Lazar, Josef; Cíp, Ondřej

2013-09-27

This paper presents a method implemented in a system for automatic contactless calibration of gauge blocks designed at ISI ASCR. The system combines low-coherence interferometry and laser interferometry, where the first identifies the gauge block sides position and the second one measures the gauge block length itself. A crucial part of the system is the algorithm for gauge block alignment to the measuring beam which is able to compensate the gauge block lateral and longitudinal tilt up to 0.141 mrad. The algorithm is also important for the gauge block position monitoring during its length measurement.

Active Angular Alignment of Gauge Blocks in Double-Ended Interferometers

PubMed Central

Buchta, Zdeněk; Řeřucha, Šimon; Hucl, Václav; Čížek, Martin; Šarbort, Martin; Lazar, Josef; Číp, Ondřej

2013-01-01

This paper presents a method implemented in a system for automatic contactless calibration of gauge blocks designed at ISI ASCR. The system combines low-coherence interferometry and laser interferometry, where the first identifies the gauge block sides position and the second one measures the gauge block length itself. A crucial part of the system is the algorithm for gauge block alignment to the measuring beam which is able to compensate the gauge block lateral and longitudinal tilt up to 0.141 mrad. The algorithm is also important for the gauge block position monitoring during its length measurement. PMID:24084107

Is subjective memory specific for memory performance or general across cognitive domains? Findings from the Seattle Longitudinal Study.

PubMed

Hülür, Gizem; Willis, Sherry L; Hertzog, Christopher; Schaie, K Warner; Gerstorf, Denis

2018-05-01

A growing body of research has examined whether people's judgments of their own memory functioning accurately reflect their memory performance at cross-section and over time. Relatively less is known about whether these judgments are specifically based on memory performance, or reflect general cognitive change. The aim of the present study was to examine longitudinal associations of subjective memory with performance in tests of episodic memory and a wide range of other cognitive tests, including the Wechsler Adult Intelligence Scale-Revised (WAIS-R) Block Design, Comprehension, Digit Span, Digit Symbol, and Vocabulary subtests. We applied latent growth curve models to five occasions over up to 16 years of neuropsychological assessments from 956 participants of the Seattle Longitudinal Study (SLS; 57% women; age at baseline: M = 65.1, SD = 11.4, 38 - 96 years). Results revealed that lower self-reported Frequency of Forgetting was significantly associated with better performance in all cognitive domains at baseline. The baseline correlation of Frequency of Forgetting with memory performance was stronger than its correlations with performance in other cognitive tests. Furthermore, additional analyses with baseline data showed that a latent memory performance factor reliably predicted Frequency of Forgetting after controlling for a general cognitive factor. Over time, steeper increases in Frequency of Forgetting were associated with steeper declines in tests of memory performance and in the Block Design and Digit Symbol subtests. Taken together, these findings suggest that although self-reported Frequency of Forgetting reflects performance in a broad range of other cognitive domains, it also shows some specificity for memory performance. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

A reuse-based framework for the design of analog and mixed-signal ICs

NASA Astrophysics Data System (ADS)

Castro-Lopez, Rafael; Fernandez, Francisco V.; Rodriguez Vazquez, Angel

2005-06-01

Despite the spectacular breakthroughs of the semiconductor industry, the ability to design integrated circuits (ICs) under stringent time-to-market (TTM) requirements is lagging behind integration capacity, so far keeping pace with still valid Moore"s Law. The resulting gap is threatening with slowing down such a phenomenal growth. The design community believes that it is only by means of powerful CAD tools and design methodologies - and, possibly, a design paradigm shift - that this design gap can be bridged. In this sense, reuse-based design is seen as a promising solution, and concepts such as IP Block, Virtual Component, and Design Reuse have become commonplace thanks to the significant advances in the digital arena. Unfortunately, the very nature of analog and mixed-signal (AMS) design has hindered a similar level of consensus and development. This paper presents a framework for the reuse-based design of AMS circuits. The framework is founded on three key elements: (1) a CAD-supported hierarchical design flow that facilitates the incorporation of AMS reusable blocks, reduces the overall design time, and expedites the management of increasing AMS design complexity; (2) a complete, clear definition of the AMS reusable block, structured into three separate facets or views: the behavioral, structural, and layout facets, the two first for top-down electrical synthesis and bottom-up verification, the latter used during bottom-up physical synthesis; (3) the design for reusability set of tools, methods, and guidelines that, relying on intensive parameterization as well as on design knowledge capture and encapsulation, allows to produce fully reusable AMS blocks. A case study and a functional silicon prototype demonstrate the validity of the paper"s proposals.

Elastic-Plastic Behaviour of Ultrasonic Assisted Compression of Polyvinyl Chloride (PVC) Foam

NASA Astrophysics Data System (ADS)

Muhalim, N. A. D.; Hassan, M. Z.; Daud, Y.

2018-04-01

The present study aims to investigate the elastic-plastic behaviour of ultrasonic assisted compression of PVC closed-cell foam. A series of static and ultrasonic compression test of PVC closed-cell foam were conducted at a constant cross head speed of 30 mm/min on dry surface condition. For quasi-static test, specimen was compressed between two rigid platens using universal testing machine. In order to evaluate the specimen behavior under ultrasonic condition, specimen was placed between a specifically design double-slotted block horn and rigid platen. The horn was designed and fabricated prior to the test as a medium to transmit the ultrasonic vibration from the ultrasonic transducer to the working specimen. It was tuned to a frequency of 19.89 kHz in longitudinal mode and provided an average oscillation amplitude at 6 µm on the uppermost surface. Following, the characteristics of stress-strain curves for quasi-static and ultrasonic compression tests were analyzed. It was found that the compressive stress was significantly reduced at the onset of superimposed ultrasonic vibration during plastic deformation.