Attacks on Bluetooth Security Architecture and Its Countermeasures

NASA Astrophysics Data System (ADS)

Iqbal, Mian Muhammad Waseem; Kausar, Firdous; Wahla, Muhammad Arif

WPANs compliment the traditional IEEE 802.11 wireless networks by facilitating the clients with flexibility in network topologies, higher mobility and relaxed configuration/hardware requirements. Bluetooth, a WPAN technology, is an open standard for short-range radio frequency (RF) communication. However, it is also susceptible to typical security threats found in wireless LANs. This paper discuses some of the attack scenarios against the bluetooth network such as hostile intrusion, active Man-in-the-Middle (MITM) attack using unit key and various forms of denial of service (DoS) attacks. These threats and attacks compromise the confidentiality and availability of bluetooth data and services. This paper proposes an improved security architecture for bluetooth device which provides protection against the above mentioned attacks.

Bluetooth Roaming for Sensor Network System in Clinical Environment.

PubMed

Kuroda, Tomohiro; Noma, Haruo; Takase, Kazuhiko; Sasaki, Shigeto; Takemura, Tadamasa

2015-01-01

A sensor network is key infrastructure for advancing a hospital information system (HIS). The authors proposed a method to provide roaming functionality for Bluetooth to realize a Bluetooth-based sensor network, which is suitable to connect clinical devices. The proposed method makes the average response time of a Bluetooth connection less than one second by making the master device repeat the inquiry process endlessly and modifies parameters of the inquiry process. The authors applied the developed sensor network for daily clinical activities in an university hospital, and confirmed the stabilitya and effectiveness of the sensor network. As Bluetooth becomes a quite common wireless interface for medical devices, the proposed protocol that realizes Bluetooth-based sensor network enables HIS to equip various clinical devices and, consequently, lets information and communication technologies advance clinical services.

Bluetooth-based distributed measurement system

NASA Astrophysics Data System (ADS)

Tang, Baoping; Chen, Zhuo; Wei, Yuguo; Qin, Xiaofeng

2007-07-01

A novel distributed wireless measurement system, which is consisted of a base station, wireless intelligent sensors and relay nodes etc, is established by combining of Bluetooth-based wireless transmission, virtual instrument, intelligent sensor, and network. The intelligent sensors mounted on the equipments to be measured acquire various parameters and the Bluetooth relay nodes get the acquired data modulated and sent to the base station, where data analysis and processing are done so that the operational condition of the equipment can be evaluated. The establishment of the distributed measurement system is discussed with a measurement flow chart for the distributed measurement system based on Bluetooth technology, and the advantages and disadvantages of the system are analyzed at the end of the paper and the measurement system has successfully been used in Daqing oilfield, China for measurement of parameters, such as temperature, flow rate and oil pressure at an electromotor-pump unit.

A wireless recording system that utilizes Bluetooth technology to transmit neural activity in freely moving animals

PubMed Central

Hampson, Robert E.; Collins, Vernell; Deadwyler, Sam A.

2009-01-01

A new wireless transceiver is described for recording individual neuron firing from behaving rats utilizing Bluetooth transmission technology and a processor onboard for discrimination of neuronal waveforms and associated time stamps. This universal brain activity transmitter (UBAT) is attached to rodents via a backpack and amplifier headstage and can transmit 16 channels of captured neuronal firing data via a Bluetooth transceiver chip over very large and unconstrained distances. The onboard microprocessor of the UBAT allows flexible online control over waveform isolation criteria via transceiver instruction and the two-way communication capacity allows for closed-loop applications between neural events and behavioral or physiological processes which can be modified by transceiver instructions. A detailed description of the multiplexer processing of channel data as well as examples of neuronal recordings in different behavioral testing contexts is provided to demonstrate the capacity for robust transmission within almost any laboratory environment. A major advantage of the UBAT is the long transmission range and lack of object-based line of sight interference afforded by Bluetooth technology, allowing flexible recording capabilities within multiple experimental paradigms without interruption. Continuous recordings over very large distance separations from the monitor station are demonstrated providing experimenters with recording advantages not previously available with other telemetry devices. PMID:19524612

A wireless recording system that utilizes Bluetooth technology to transmit neural activity in freely moving animals.

PubMed

Hampson, Robert E; Collins, Vernell; Deadwyler, Sam A

2009-09-15

A new wireless transceiver is described for recording individual neuron firing from behaving rats utilizing Bluetooth transmission technology and a processor onboard for discrimination of neuronal waveforms and associated time stamps. This universal brain activity transmitter (UBAT) is attached to rodents via a backpack and amplifier headstage and can transmit 16 channels of captured neuronal firing data via a Bluetooth transceiver chip over very large and unconstrained distances. The onboard microprocessor of the UBAT allows flexible online control over waveform isolation criteria via transceiver instruction and the two-way communication capacity allows for closed-loop applications between neural events and behavioral or physiological processes which can be modified by transceiver instructions. A detailed description of the multiplexer processing of channel data as well as examples of neuronal recordings in different behavioral testing contexts is provided to demonstrate the capacity for robust transmission within almost any laboratory environment. A major advantage of the UBAT is the long transmission range and lack of object-based line of sight interference afforded by Bluetooth technology, allowing flexible recording capabilities within multiple experimental paradigms without interruption. Continuous recordings over very large distance separations from the monitor station are demonstrated providing experimenters with recording advantages not previously available with other telemetry devices.

Self-activating intelligent home using bluetooth

NASA Astrophysics Data System (ADS)

Karthikeyan, P.; Sumanth, N.; Jude, S.

2017-11-01

Homes today need to exploit the various technologies available to make them intelligent. In this paper, a wireless system is proposed to automate home appliances using Bluetooth. This system can be used from a Bluetooth module that is closer than 10 meters to the system. Once in range, various appliances can be self-activated by the software that is built into a microcontroller. It is envisioned to offer automation of doors, lights and various electrical appliances. It also offers a complete user based automation for an improved personal experience.

Bluetooth as a Playful Public Art Interface

NASA Astrophysics Data System (ADS)

Stukoff, Maria N.

This chapter investigates how the application of emergent communication technologies assisted in the design of playful art experience in a public place. Every Passing Moment (EPM), was a mobile public artwork that tracked and recorded any discoverable Bluetooth device to automatically seed a flower in a virtual garden projected onto an urban screen. The EPM was the first public art work to run blu_box, a custom-designed Bluetooth system for mobile telephony. The aim of blu_box was to build a system that supported playful interactions between the public and an urban screen, openly accessible to anyone with a Bluetooth-enabled mobile phone. This participatory engagement was observed in EPM on three levels, namely; unconscious, conscious, and dynamic play. Furthermore, this chapter highlights how sound and face-to-face communication proved imperative in the play dynamics of EPM. In conclusion, this chapter proposes ways in which the use of emergent communication technologies in public places, especially when interfaced with urban screening platforms, can construct playful city spaces for the public at large.

GBSFP: General Bluetooth Scatternet Formation Protocol for Ad Hoc Networking

NASA Astrophysics Data System (ADS)

Lim, Chaegwon; Huh, Myung-Sun; Choi, Chong-Ho; Jeong, Gu-Min

Recently, bluetooth technology has become widely prevalent so that many laptops and mobile phones are equipped with bluetooth capability. In order to meet the increasing demand to interconnect these devices a new scatternet formation protocol named GBSFP (General Bluetooth Scatternet Formation Protocol) is proposed in this paper. GBSFP is the result of efforts to overcome the two major limitations of the legacy scatternet formation protocols as regards their real implementation, that all of the nodes should be within the Bluetooth communication range or that they should be time synchronized. In GBSFP, a node goes through three phases; 1) the Init phase to establish a bluetooth link to as many of its neighbors as possible, 2) the Ready phase to determine the role of each node, i.e., master or slave, and remove any unnecessary bluetooth links, and 3) the Complete phase to finalize the formation of the scatternet and begin data transmission. The simulation results show that GBSFP provides higher connectivity in many scenarios compared with BTCP and BlueStars.

Modeling of human movement monitoring using Bluetooth Low Energy technology.

PubMed

Mokhtari, G; Zhang, Q; Karunanithi, M

2015-01-01

Bluetooth Low Energy (BLE) is a wireless communication technology which can be used to monitor human movements. In this monitoring system, a BLE signal scanner scans signal strength of BLE tags carried by people, to thus infer human movement patterns within its monitoring zone. However to the extent of our knowledge one main aspect of this monitoring system which has not yet been thoroughly investigated in literature is how to build a sound theoretical model, based on tunable BLE communication parameters such as scanning time interval and advertising time interval, to enable the study and design of effective and efficient movement monitoring systems. In this paper, we proposed and developed a statistical model based on Monte-Carlo simulation, which can be utilized to assess impacts of BLE technology parameters in terms of latency and efficiency, on a movement monitoring system, and can thus benefit a more efficient system design.

Bluetooth Low Power Modes Applied to the Data Transportation Network in Home Automation Systems.

PubMed

Etxaniz, Josu; Aranguren, Gerardo

2017-04-30

Even though home automation is a well-known research and development area, recent technological improvements in different areas such as context recognition, sensing, wireless communications or embedded systems have boosted wireless smart homes. This paper focuses on some of those areas related to home automation. The paper draws attention to wireless communications issues on embedded systems. Specifically, the paper discusses the multi-hop networking together with Bluetooth technology and latency, as a quality of service (QoS) metric. Bluetooth is a worldwide standard that provides low power multi-hop networking. It is a radio license free technology and establishes point-to-point and point-to-multipoint links, known as piconets, or multi-hop networks, known as scatternets. This way, many Bluetooth nodes can be interconnected to deploy ambient intelligent networks. This paper introduces the research on multi-hop latency done with park and sniff low power modes of Bluetooth over the test platform developed. Besides, an empirical model is obtained to calculate the latency of Bluetooth multi-hop communications over asynchronous links when links in scatternets are always in sniff or the park mode. Smart home devices and networks designers would take advantage of the models and the estimation of the delay they provide in communications along Bluetooth multi-hop networks.

Bluetooth Low Power Modes Applied to the Data Transportation Network in Home Automation Systems

PubMed Central

Etxaniz, Josu; Aranguren, Gerardo

2017-01-01

Even though home automation is a well-known research and development area, recent technological improvements in different areas such as context recognition, sensing, wireless communications or embedded systems have boosted wireless smart homes. This paper focuses on some of those areas related to home automation. The paper draws attention to wireless communications issues on embedded systems. Specifically, the paper discusses the multi-hop networking together with Bluetooth technology and latency, as a quality of service (QoS) metric. Bluetooth is a worldwide standard that provides low power multi-hop networking. It is a radio license free technology and establishes point-to-point and point-to-multipoint links, known as piconets, or multi-hop networks, known as scatternets. This way, many Bluetooth nodes can be interconnected to deploy ambient intelligent networks. This paper introduces the research on multi-hop latency done with park and sniff low power modes of Bluetooth over the test platform developed. Besides, an empirical model is obtained to calculate the latency of Bluetooth multi-hop communications over asynchronous links when links in scatternets are always in sniff or the park mode. Smart home devices and networks designers would take advantage of the models and the estimation of the delay they provide in communications along Bluetooth multi-hop networks. PMID:28468294

Mobile based Appliances switching using Bluetooth

NASA Astrophysics Data System (ADS)

Gupta, Sureshchandra J., Dr; Desai, Kalp; Gaikawad, Deepak; Pawar, Vijay N.; Gangal, Devendranath R.

2008-04-01

How many times do you have to get up from your desk to switch on your Air conditioner or fan when you are completely into your table work? How many times do you feel lazy to get off your comfort to switch on/off your home appliances in different rooms? How much energy do you lose in a day for operating your appliances? The solution is either a large amount of manual work—or the idea that is presented over here: APP-CON (APP-CON stands for appliances control). Here the ordinary cell phone with bluetooth capability acts as remote designed in such a manner that it acts as a helping hand to human by reducing its manual work and therefore saving human energy. The cell phone control of APP-CON units lets you access many of your home appliances situated in different rooms by using just a single remote from distance. Electronics hobbyists would love to make such a remote control themselves. But they find it difficult due to complex circuitry rather than the high cost because of using a number of frequency counting techniques and decade counters. The APP-CON system given here overcomes the aforesaid problems by using a single microcontroller and moreover a simple program or software for bluetooth enabled cell phone and employing simple coding and decoding of remote signals. Here the mobile based remote control is used to operate a number of home appliances basically consists of Bluetooth technology. The unit consists of a transmitter and a receiver consisting of a microcontroller. The importance of bluetooth technology is that the signal to be transmitted from transmitter to the receiver is done without requiring line of sight.

Design and implementation of Bluetooth beacon in mobile payment system

NASA Astrophysics Data System (ADS)

Han, Tiantian; Ding, Lei

2017-08-01

The current line of payment means, mainly in the following ways, cash payment, credit card payment, WeChat Alipay sweep payment. There are many inconvenience in Cash payment, large amounts of cash inconvenience to carry, count the money to spend time and effort, true and false banknotes difficult to distinguish, ticket settlement easy to go wrong. Credit card payment is relatively time-consuming, and WeChat Alipay sweep payment need to sweep. Therefore, the design of a convenient, fast payment to meet the line to pay the demand is particularly important. Based on the characteristics of BLE Bluetooth wireless communication technology, this paper designs a kind of payment method based on Bluetooth beacon. Through the Bluetooth beacon broadcast consumption, consumers only need to open the relevant APP in the Android client, and you can get Bluetooth via mobile phone Bluetooth the amount of consumption of the standard broadcast, in accordance with the corresponding payment platform to complete the payment process, which pay less time to improve the efficiency of payment.

Designing of Roaming Protocol for Bluetooth Equipped Multi Agent Systems

NASA Astrophysics Data System (ADS)

Subhan, Fazli; Hasbullah, Halabi B.

Bluetooth is an established standard for low cost, low power, wireless personal area network. Currently, Bluetooth does not support any roaming protocol in which handoff occurs dynamically when a Bluetooth device is moving out of the piconet. If a device is losing its connection to the master device, no provision is made to transfer it to another master. Handoff is not possible in a piconet, as in order to stay within the network, a slave would have to keep the same master. So, by definition intra-handoff is not possible within a piconet. This research mainly focuses on Bluetooth technology and designing a roaming protocol for Bluetooth equipped multi agent systems. A mathematical model is derived for an agent. The idea behind the mathematical model is to know when to initiate the roaming process for an agent. A desired trajectory for the agent is calculated using its x and y coordinates system, and is simulated in SIMULINK. Various roaming techniques are also studied and discussed. The advantage of designing a roaming protocol is to ensure the Bluetooth enabled roaming devices can freely move inside the network coverage without losing its connection or break of service in case of changing the base stations.

Analysis of bluetooth and wi-fi technology to measure wait times of personal vehicles at Arizona-Mexico ports of entry.

DOT National Transportation Integrated Search

2015-11-01

Robust travel time data collection is possible using Bluetooth or Wi-Fi technology that : matches anonymous MAC addresses from discoverable electronic devices (e.g., smart phones) : to determine travel time along a roadway segment. Several hundred...

Objective and perceptual comparisons of two bluetooth hearing aid assistive devices.

PubMed

Clark, Jackie L; Pustejovsky, Carmen; Vanneste, Sven

2017-08-01

With the advent of Bluetooth technology, many of the assistive listening devices for hearing have become manufacturer specific, with little objective information about the performance provided. Thirty native English-speaking adults (mean age 29.8) with normal hearing were tested pseudo-randomly with two major hearing aid manufacturers' proprietary Bluetooth connectivity devices paired to the accompanying manufacturer's specific hearing aids. Sentence recognition performance was objectively measured for each system with signals transmitted via a land-line to the same iPhone in two conditions. There was a significant effect of participant's performance according to listening condition. There was no significant effect between device manufacturers according to listening condition, but there was a significant effect in participant's perception of "quality of sound". Despite differences in signal transmission for each devise, when worn by participants both the systems performed equally. In fact, participants expressed personal preferences for specific technology that was largely due to their perceived quality of sound while listening to recorded signals. While further research is necessary to investigate other measures of benefit for Bluetooth connectivity devices, preliminary data suggest that in order to ensure comfort and compatibility, not only should objective measures of the patient benefit be completed, but also assessing the patient's perception of benefit is equally important. Implications for Rehabilitation All professionals who work with individuals with hearing loss, become aware of the differences in the multiple choices for assistive technology readily available for hearing loss. With the ever growing dispensing of Bluetooth connectivity devices coupled to hearing aids, there is an increased burden to determine whether performance differences could exist between manufacturers. There is a growing need to investigate other measures of benefit for Bluetooth

Bluetooth data collection system for planning and arterial management.

DOT National Transportation Integrated Search

2014-08-01

This report presents the results of a research and development project of an implementable portable wireless traffic data collection system. Utilizing Bluetooth wireless technology as a platform, portable battery powered data collection units housed ...

[Intelligent watch system for health monitoring based on Bluetooth low energy technology].

PubMed

Wang, Ji; Guo, Hailiang; Ren, Xiaoli

2017-08-01

According to the development status of wearable technology and the demand of intelligent health monitoring, we studied the multi-function integrated smart watches solution and its key technology. First of all, the sensor technology with high integration density, Bluetooth low energy (BLE) and mobile communication technology were integrated and used in develop practice. Secondly, for the hardware design of the system in this paper, we chose the scheme with high integration density and cost-effective computer modules and chips. Thirdly, we used real-time operating system FreeRTOS to develop the friendly graphical interface interacting with touch screen. At last, the high-performance application software which connected with BLE hardware wirelessly and synchronized data was developed based on android system. The function of this system included real-time calendar clock, telephone message, address book management, step-counting, heart rate and sleep quality monitoring and so on. Experiments showed that the collecting data accuracy of various sensors, system data transmission capacity, the overall power consumption satisfy the production standard. Moreover, the system run stably with low power consumption, which could realize intelligent health monitoring effectively.

Coexistence of Collocated IEEE 802.11 and Bluetooth Technologies in 2.4 GHz ISM Band

NASA Astrophysics Data System (ADS)

Xhafa, Ariton E.; Lu, Xiaolin; Shaver, Donald P.

In this paper, we investigate coexistence of collocated 802.11 and Bluetooth technologies in 2.4 GHz industrial, scientific, and medical (ISM) band. To that end, we show a time division multiplexing approach suffers from the “avalanche effect”. We then provide remedies to avoid this effect and improve the performance of the overall network. For example, it is shown that a simple request-to-send (RTS) / clear-to-send (CTS) frame handshake in WLAN can avoid “avalanche effect” and improve the performance of overall network.

Provisioning Vehicular Services and Communications Based on a Bluetooth Sensor Network Deployment

PubMed Central

Perez-Diaz de Cerio, David; Valenzuela, José Luis

2015-01-01

It is very common to rule out Bluetooth as a suitable technology for vehicular communications. The reasons behind this decision usually result from misconceptions such as accepting that Bluetooth has a short application range, or assuming its connection setup is not fast enough to allow communication which involves high speed moving nodes. This paper refutes those assertions and proposes the use of Bluetooth not only for Infrastructure-to-Vehicle (I2V) or Road-to-Vehicle (R2V) communications, but also for Vehicle-to-Vehicle (V2V) or Vehicle-to-Infrastructure (V2I) communications. This novel proposal is based on using the remote name request procedure of the standard, combined with an adjustment and optimization of the parameters present in the inquiry and page procedures. The proposed modifications reduce the information exchange delay, thus making Bluetooth a suitable technology for high-speed vehicle communications. The feasibility of the proposed scheme has been validated through experimental tests conducted in different scenarios: laboratory, a real highway and a racing test circuit. There, the communication system was installed in a vehicle circulating at speeds of up to 250 km/h, whereas autonomous devices were disseminated throughout the road path to communicate with the on board devices obtaining satisfying results. PMID:26035350

Provisioning vehicular services and communications based on a bluetooth sensor network deployment.

PubMed

de Cerio, David Perez-Diaz; Valenzuela, José Luis

2015-05-29

It is very common to rule out Bluetooth as a suitable technology for vehicular communications. The reasons behind this decision usually result from misconceptions such as accepting that Bluetooth has a short application range, or assuming its connection setup is not fast enough to allow communication which involves high speed moving nodes. This paper refutes those assertions and proposes the use of Bluetooth not only for Infrastructure-to-Vehicle (I2V) or Road-to-Vehicle (R2V) communications, but also for Vehicle-to-Vehicle (V2V) or Vehicle-to-Infrastructure (V2I) communications. This novel proposal is based on using the remote name request procedure of the standard, combined with an adjustment and optimization of the parameters present in the inquiry and page procedures. The proposed modifications reduce the information exchange delay, thus making Bluetooth a suitable technology for high-speed vehicle communications. The feasibility of the proposed scheme has been validated through experimental tests conducted in different scenarios: laboratory, a real highway and a racing test circuit. There, the communication system was installed in a vehicle circulating at speeds of up to 250 km/h, whereas autonomous devices were disseminated throughout the road path to communicate with the on board devices obtaining satisfying results.

Bluetooth Communication for Battery Powered Medical Devices

NASA Astrophysics Data System (ADS)

Babušiak, Branko; Borik, Štefan

2016-01-01

wireless communication eliminates obtrusive cables associated with wearable sensors and considerably increases patient comfort during measurement and collection of medical data. Wireless communication is very popular in recent years and plays a significant role in telemedicine and homecare applications. Bluetooth technology is one of the most commonly used wireless communication types in medicine. This paper describes the design of a universal wireless communication device with excellent price/performance ratio. The said device is based on the low-cost RN4020 Bluetooth module with Microchip Low-energy Data Profile (MLDP) and due to low-power consumption is especially suitable for the transmission of biological signals (ECG, EMG, PPG, etc.) from wearable medical/personal health devices. A unique USB dongle adaptor was developed for wireless communication via UART interface and power consumption was evaluated under various conditions.

Application of the Blobo bluetooth ball in wrist rehabilitation training

PubMed Central

Hsieh, Wei-Min; Hwang, Yuh-Shyan; Chen, Shih-Ching; Tan, Sun-Yen; Chen, Chih-Chen; Chen, Yu-Luen

2016-01-01

[Purpose] The introduction of emerging technologies such as the wireless Blobo bluetooth ball with multimedia features can enhance wrist physical therapy training, making it more fun and enhancing its effects. [Methods] Wrist injuries caused by fatigue at work, improper exercise, and other conditions are very common. Therefore, the reconstruction of wrist joint function is an important issue. The efficacy of a newly developed integrated wrist joint rehabilitation game using a Blobo bluetooth ball with C# software installed was tested in wrist rehabilitation (Flexion, Extension, Ulnar Deviation, Radial Deviation). [Results] Eight subjects with normal wrist function participated in a test of the system’s stability and repeatability. After performing the Blobo bluetooth ball wrist physical therapy training, eight patients with wrist dysfunction experienced approximately 10° improvements in range of motion (ROM) of flexion extension, and ulnar deviation and about 6° ROM improvement in radial deviation. The subjects showed progress in important indicators of wrist function. [Conclusion] This study used the Blobo bluetooth ball in wrist physical therapy training and the preliminary results were encouraging. In the future, more diverse wrist or limb rehabilitation games should be developed to meet the needs of physical therapy training. PMID:26957723

Application of the Blobo bluetooth ball in wrist rehabilitation training.

PubMed

Hsieh, Wei-Min; Hwang, Yuh-Shyan; Chen, Shih-Ching; Tan, Sun-Yen; Chen, Chih-Chen; Chen, Yu-Luen

2016-01-01

[Purpose] The introduction of emerging technologies such as the wireless Blobo bluetooth ball with multimedia features can enhance wrist physical therapy training, making it more fun and enhancing its effects. [Methods] Wrist injuries caused by fatigue at work, improper exercise, and other conditions are very common. Therefore, the reconstruction of wrist joint function is an important issue. The efficacy of a newly developed integrated wrist joint rehabilitation game using a Blobo bluetooth ball with C# software installed was tested in wrist rehabilitation (Flexion, Extension, Ulnar Deviation, Radial Deviation). [Results] Eight subjects with normal wrist function participated in a test of the system's stability and repeatability. After performing the Blobo bluetooth ball wrist physical therapy training, eight patients with wrist dysfunction experienced approximately 10° improvements in range of motion (ROM) of flexion extension, and ulnar deviation and about 6° ROM improvement in radial deviation. The subjects showed progress in important indicators of wrist function. [Conclusion] This study used the Blobo bluetooth ball in wrist physical therapy training and the preliminary results were encouraging. In the future, more diverse wrist or limb rehabilitation games should be developed to meet the needs of physical therapy training.

Bluetooth wireless database for scoliosis clinics.

PubMed

Lou, E; Fedorak, M V; Hill, D L; Raso, J V; Moreau, M J; Mahood, J K

2003-05-01

A database system with Bluetooth wireless connectivity has been developed so that scoliosis clinics can be run more efficiently and data can be mined for research studies without significant increases in equipment cost. The wireless database system consists of a Bluetooth-enabled laptop or PC and a Bluetooth-enabled handheld personal data assistant (PDA). Each patient has a profile in the database, which has all of his or her clinical history. Immediately prior to the examination, the orthopaedic surgeon selects a patient's profile from the database and uploads that data to the PDA over a Bluetooth wireless connection. The surgeon can view the entire clinical history of the patient while in the examination room and, at the same time, enter in any new measurements and comments from the current examination. After seeing the patient, the surgeon synchronises the newly entered information with the database wirelessly and prints a record for the chart. This combination of the database and the PDA both improves efficiency and accuracy and can save significant time, as there is less duplication of work, and no dictation is required. The equipment required to implement this solution is a Bluetooth-enabled PDA and a Bluetooth wireless transceiver for the PC or laptop.

Evaluation of Bluetooth communications for the deployment of assisted living technologies in home environments.

PubMed

McGrath, Michael J; Burns, Adrian; Dishongh, Terry

2007-01-01

Using five different commercially available class one and class two Bluetooth dongles a total of seven homes which represented a cross section of typical Irish homes were surveyed to determine the effect of construction methods, house size, sensor placement, host placement, antenna design and RF interference had on the link quality of Bluetooth enabled sensors. The results obtained indicates there is high variability in the link quality which is determined by the quality of the BT radio, placement of the antenna on both the master and slave, the number of walls which must be penetrated and the construction materials used in the wall. The placement of the sensor was the single biggest factor in determining the link quality. The type of construction used in the interior walls has significant influence also. The final factor of significant influence was the type of antenna used on the Bluetooth dongle. The use of an external antenna gave significantly better range performance than an internal antenna.

Bluetooth based function control in a car

NASA Astrophysics Data System (ADS)

Karthikeyan, P.; Sumanth, N.; Jude, S.

2017-11-01

This paper aims to show the various functions that can be controlled in a Car using the Wireless Bluetooth Technology. Due to the portable and wireless nature of this technology, it is easier for the end user to operate the functions in a car. The functions that are built into the system can be used from a distance of 10 meters. The Passive Keyless System and the Remote Keyless System methodologies are adopted. These are operated by the ATMEGA328P microcontroller.

Generic Bluetooth Data Module

DTIC Science & Technology

2002-09-01

to Ref (1). 34 RS232.java Serial Coomunication port class To Bluetooth module HCI.java Host Control Interface class L2CAP.java Logical Link Control...standard protocol for transporting IP datagrams over point-to-point link . It is designed to run over RFCOMM to accomplish point-to-point connections...Control and Adaption Host Controller Interface Link Manager Baseband / Link Controller Radio Figure 2. Bluetooth layers (From Ref. [3].) C

Bluetooth-based wireless sensor networks

NASA Astrophysics Data System (ADS)

You, Ke; Liu, Rui Qiang

2007-11-01

In this work a Bluetooth-based wireless sensor network is proposed. In this bluetooth-based wireless sensor networks, information-driven star topology and energy-saved mode are used, through which a blue master node can control more than seven slave node, the energy of each sensor node is reduced and secure management of each sensor node is improved.

Bluetooth traffic detectors for use as permanently installed travel time instruments.

DOT National Transportation Integrated Search

2012-02-06

In February 2009, the University of Marylands (UMD) Center for Advanced Transportation Technology : (CATT) via a research grant from the Maryland State Highway Administration (SHA) set out to extend : Bluetooth TM traffic monitoring (BTM) technolo...

Coexistence issues for a 2.4 GHz wireless audio streaming in presence of bluetooth paging and WLAN

NASA Astrophysics Data System (ADS)

Pfeiffer, F.; Rashwan, M.; Biebl, E.; Napholz, B.

2015-11-01

Nowadays, customers expect to integrate their mobile electronic devices (smartphones and laptops) in a vehicle to form a wireless network. Typically, IEEE 802.11 is used to provide a high-speed wireless local area network (WLAN) and Bluetooth is used for cable replacement applications in a wireless personal area network (PAN). In addition, Daimler uses KLEER as third wireless technology in the unlicensed (UL) 2.4 GHz-ISM-band to transmit full CD-quality digital audio. As Bluetooth, IEEE 802.11 and KLEER are operating in the same frequency band, it has to be ensured that all three technologies can be used simultaneously without interference. In this paper, we focus on the impact of Bluetooth and IEEE 802.11 as interferer in presence of a KLEER audio transmission.

Automatic Bluetooth testing for mobile multi-user applications

NASA Astrophysics Data System (ADS)

Luck, Dennis; Hörning, Henrik; Edlich, Stefan

2008-02-01

In this paper we present a simple approach for the development of multiuser and multimedia applications based on Bluetooth. One main obstacle for Bluetooth synchronization of mobile applications is the lack of a complete specification implementation. Nowadays these applications must be on market as fast as possible. Hence, developers must be able to test several dozens of mobile devices for their Bluetooth capability. And surprisingly, the capabilities differ not only between the Bluetooth specification 1.0 and 2.0. The current development was triggered by the development of mass applications as mobile multiuser games (e.g. Tetris). Our Application can be distributed on several mobile phones. If started, the Bluetooth applications try to connect each other and automatically start to detect device capabilities. These capabilities will be gathered and distributed to a server. The server performs statistical investigations and aggregates them to be presented as a report. The result is a faster development regarding mobile communications.

Optimization of wireless Bluetooth sensor systems.

PubMed

Lonnblad, J; Castano, J; Ekstrom, M; Linden, M; Backlund, Y

2004-01-01

Within this study, three different Bluetooth sensor systems, replacing cables for transmission of biomedical sensor data, have been designed and evaluated. The three sensor architectures are built on 1-, 2- and 3-chip solutions and depending on the monitoring situation and signal character, different solutions are optimal. Essential parameters for all systems have been low physical weight and small size, resistance to interference and interoperability with other technologies as global- or local networks, PC's and mobile phones. Two different biomedical input signals, ECG and PPG (photoplethysmography), have been used to evaluate the three solutions. The study shows that it is possibly to continuously transmit an analogue signal. At low sampling rates and slowly varying parameters, as monitoring the heart rate with PPG, the 1-chip solution is the most suitable, offering low power consumption and thus a longer battery lifetime or a smaller battery, minimizing the weight of the sensor system. On the other hand, when a higher sampling rate is required, as an ECG, the 3-chip architecture, with a FPGA or micro-controller, offers the best solution and performance. Our conclusion is that Bluetooth might be useful in replacing cables of medical monitoring systems.

An Indoor Positioning-Based Mobile Payment System Using Bluetooth Low Energy Technology

PubMed Central

Winata, Doni

2018-01-01

The development of information technology has paved the way for faster and more convenient payment process flows and new methodology for the design and implementation of next generation payment systems. The growth of smartphone usage nowadays has fostered a new and popular mobile payment environment. Most of the current generation smartphones support Bluetooth Low Energy (BLE) technology to communicate with nearby BLE-enabled devices. It is plausible to construct an Over-the-Air BLE-based mobile payment system as one of the payment methods for people living in modern societies. In this paper, a secure indoor positioning-based mobile payment authentication protocol with BLE technology and the corresponding mobile payment system design are proposed. The proposed protocol consists of three phases: initialization phase, session key construction phase, and authentication phase. When a customer moves toward the POS counter area, the proposed mobile payment system will automatically detect the position of the customer to confirm whether the customer is ready for the checkout process. Once the system has identified the customer is standing within the payment-enabled area, the payment system will invoke authentication process between POS and the customer’s smartphone through BLE communication channel to generate a secure session key and establish an authenticated communication session to perform the payment transaction accordingly. A prototype is implemented to assess the performance of the proposed design for mobile payment system. In addition, security analysis is conducted to evaluate the security strength of the proposed protocol. PMID:29587399

An Indoor Positioning-Based Mobile Payment System Using Bluetooth Low Energy Technology.

PubMed

Yohan, Alexander; Lo, Nai-Wei; Winata, Doni

2018-03-25

The development of information technology has paved the way for faster and more convenient payment process flows and new methodology for the design and implementation of next generation payment systems. The growth of smartphone usage nowadays has fostered a new and popular mobile payment environment. Most of the current generation smartphones support Bluetooth Low Energy (BLE) technology to communicate with nearby BLE-enabled devices. It is plausible to construct an Over-the-Air BLE-based mobile payment system as one of the payment methods for people living in modern societies. In this paper, a secure indoor positioning-based mobile payment authentication protocol with BLE technology and the corresponding mobile payment system design are proposed. The proposed protocol consists of three phases: initialization phase, session key construction phase, and authentication phase. When a customer moves toward the POS counter area, the proposed mobile payment system will automatically detect the position of the customer to confirm whether the customer is ready for the checkout process. Once the system has identified the customer is standing within the payment-enabled area, the payment system will invoke authentication process between POS and the customer's smartphone through BLE communication channel to generate a secure session key and establish an authenticated communication session to perform the payment transaction accordingly. A prototype is implemented to assess the performance of the proposed design for mobile payment system. In addition, security analysis is conducted to evaluate the security strength of the proposed protocol.

Wireless multipoint communication for optical sensors in the industrial environment using the new Bluetooth standard

NASA Astrophysics Data System (ADS)

Hussmann, Stephan; Lau, Wing Y.; Chu, Terry; Grothof, Markus

2003-07-01

Traditionally, the measuring or monitoring system of manufacturing industries uses sensors, computers and screens for their quality control (Q.C.). The acquired information is fed back to the control room by wires, which - for obvious reason - are not suitable in many environments. This paper describes a method to solve this problem by employing the new Bluetooth technology to set up a complete new system, where a total wireless solution is made feasible. This new Q.C. system allows several line scan cameras to be connected at once to a graphical user interface (GUI) that can monitor the production process. There are many Bluetooth devices available on the market such as cell-phones, headsets, printers, PDA etc. However, the detailed application is a novel implementation in the industrial Q.C. area. This paper will contain more details about the Bluetooth standard and why it is used (nework topologies, host controller interface, data rates, etc.), the Bluetooth implemetation in the microcontroller of the line scan camera, and the GUI and its features.

Bluetooth Heart Rate Monitors For Spaceflight

NASA Technical Reports Server (NTRS)

Buxton, R. E.; West, M. R.; Kalogera, K. L.; Hanson, A. M.

2016-01-01

Heart rate monitoring is required for crewmembers during exercise aboard the International Space Station (ISS) and will be for future exploration missions. The cardiovascular system must be sufficiently stressed throughout a mission to maintain the ability to perform nominal and contingency/emergency tasks. High quality heart rate data are required to accurately determine the intensity of exercise performed by the crewmembers and show maintenance of VO2max. The quality of the data collected on ISS is subject to multiple limitations and is insufficient to meet current requirements. PURPOSE: To evaluate the performance of commercially available Bluetooth heart rate monitors (BT_HRM) and their ability to provide high quality heart rate data to monitor crew health aboard the ISS and during future exploration missions. METHODS: Nineteen subjects completed 30 data collection sessions of various intensities on the treadmill and/or cycle. Subjects wore several BT_HRM technologies for each testing session. One electrode-based chest strap (CS) was worn, while one or more optical sensors (OS) were worn. Subjects were instrumented with a 12-lead ECG to compare the heart rate data from the Bluetooth sensors. Each BT_HRM data set was time matched to the ECG data and a +/-5bpm threshold was applied to the difference between the 2 data sets. Percent error was calculated based on the number of data points outside the threshold and the total number of data points. RESULTS: The electrode-based chest straps performed better than the optical sensors. The best performing CS was CS1 (1.6% error), followed by CS4 (3.3% error), CS3 (6.4% error), and CS2 (9.2% error). The OS resulted in 10.4% error for OS1 and 14.9% error for OS2. CONCLUSIONS: The highest quality data came from CS1, but unfortunately it has been discontinued by the manufacturer. The optical sensors have not been ruled out for use, but more investigation is needed to determine how to obtain the best quality data. CS2 will be

Bluetooth technology for prevention of dental caries.

PubMed

Kolahi, Jafar; Fazilati, Mohamad

2009-12-01

Caries is caused when the pH at the tooth surface drops below 5.5. A miniaturized and autonomous pH monitoring nodes can be attached to the tooth surface, like a tooth jewel. This intelligent sensor includes three components: (a) digital micro pH meter, (b) power supply, (c) wireless communicating device. The micro pH meter facilitates long term tooth surface pH monitoring and providing real time feedback to the patients and dental experts. Power supply of this system will be microfabricated biocatalytic fuel cell (enzymatic micro-battery) using organic compounds (e.g. formate or glucose) as the fuel to generate electricity. When micro pH meter detects the pH lower than 5.5, wireless Bluetooth device sends a caution (e.g. "you are at risk of dental caries") to external monitoring equipment such as mobile phone or a hands-free heads. After reception of the caution, subjects should use routine brushing and flossing procedure or use a medicated chewing gum (e.g. chlorhexidine containing chewing gum) or rinse with a mouthwash.

A Low-Cost Tracking System for Running Race Applications Based on Bluetooth Low Energy Technology.

PubMed

Perez-Diaz-de-Cerio, David; Hernández-Solana, Ángela; Valdovinos, Antonio; Valenzuela, Jose Luis

2018-03-20

Timing points used in running races and other competition events are generally based on radio-frequency identification (RFID) technology. Athletes' times are calculated via passive RFID tags and reader kits. Specifically, the reader infrastructure needed is complex and requires the deployment of a mat or ramps which hide the receiver antennae under them. Moreover, with the employed tags, it is not possible to transmit additional and dynamic information such as pulse or oximetry monitoring, alarms, etc. In this paper we present a system based on two low complex schemes allowed in Bluetooth Low Energy (BLE): the non-connectable undirected advertisement process and a modified version of scannable undirected advertisement process using the new capabilities present in Bluetooth 5. After fully describing the system architecture, which allows full real-time position monitoring of the runners using mobile phones on the organizer side and BLE sensors on the participants' side, we derive the mobility patterns of runners and capacity requirements, which are determinant for evaluating the performance of the proposed system. They have been obtained from the analysis of the real data measured in the last Barcelona Marathon. By means of simulations, we demonstrate that, even under disadvantageous conditions (50% error ratio), both schemes perform reliably and are able to detect the 100% of the participants in all the cases. The cell coverage of the system needs to be adjusted when non-connectable process is considered. Nevertheless, through simulation and experimental, we show that the proposed scheme based on the new events available in Bluetooth 5 is clearly the best implementation alternative for all the cases, no matter the coverage area and the runner speed. The proposal widely exceeds the detection requirements of the real scenario, surpassing the measured peaks of 20 sensors per second incoming in the coverage area, moving at speeds that range from 1.5 m/s to 6.25 m/s. The

A Low-Cost Tracking System for Running Race Applications Based on Bluetooth Low Energy Technology

PubMed Central

2018-01-01

Timing points used in running races and other competition events are generally based on radio-frequency identification (RFID) technology. Athletes’ times are calculated via passive RFID tags and reader kits. Specifically, the reader infrastructure needed is complex and requires the deployment of a mat or ramps which hide the receiver antennae under them. Moreover, with the employed tags, it is not possible to transmit additional and dynamic information such as pulse or oximetry monitoring, alarms, etc. In this paper we present a system based on two low complex schemes allowed in Bluetooth Low Energy (BLE): the non-connectable undirected advertisement process and a modified version of scannable undirected advertisement process using the new capabilities present in Bluetooth 5. After fully describing the system architecture, which allows full real-time position monitoring of the runners using mobile phones on the organizer side and BLE sensors on the participants’ side, we derive the mobility patterns of runners and capacity requirements, which are determinant for evaluating the performance of the proposed system. They have been obtained from the analysis of the real data measured in the last Barcelona Marathon. By means of simulations, we demonstrate that, even under disadvantageous conditions (50% error ratio), both schemes perform reliably and are able to detect the 100% of the participants in all the cases. The cell coverage of the system needs to be adjusted when non-connectable process is considered. Nevertheless, through simulation and experimental, we show that the proposed scheme based on the new events available in Bluetooth 5 is clearly the best implementation alternative for all the cases, no matter the coverage area and the runner speed. The proposal widely exceeds the detection requirements of the real scenario, surpassing the measured peaks of 20 sensors per second incoming in the coverage area, moving at speeds that range from 1.5 m/s to 6.25 m

Mobile mapping of sporting event spectators using bluetooth sensors: tour of flanders 2011.

PubMed

Versichele, Mathias; Neutens, Tijs; Goudeseune, Stephanie; van Bossche, Frederik; van de Weghe, Nico

2012-10-22

Accurate spatiotemporal information on crowds is a necessity for a better management in general and for the mitigation of potential security risks. The large numbers of individuals involved and their mobility, however, make generation of this information non-trivial. This paper proposes a novel methodology to estimate and map crowd sizes using mobile Bluetooth sensors and examines to what extent this methodology represents a valuable alternative to existing traditional crowd density estimation methods. The proposed methodology is applied in a unique case study that uses Bluetooth technology for the mobile mapping of spectators of the Tour of Flanders 2011 road cycling race. The locations of nearly 16,000 cell phones of spectators along the race course were registered and detailed views of the spatiotemporal distribution of the crowd were generated. Comparison with visual head counts from camera footage delivered a detection ratio of 13.0 ± 2.3%, making it possible to estimate the crowd size. To our knowledge, this is the first study that uses mobile Bluetooth sensors to count and map a crowd over space and time.

Mobile Mapping of Sporting Event Spectators Using Bluetooth Sensors: Tour of Flanders 2011

PubMed Central

Versichele, Mathias; Neutens, Tijs; Goudeseune, Stephanie; van Bossche, Frederik; van de Weghe, Nico

2012-01-01

Accurate spatiotemporal information on crowds is a necessity for a better management in general and for the mitigation of potential security risks. The large numbers of individuals involved and their mobility, however, make generation of this information non-trivial. This paper proposes a novel methodology to estimate and map crowd sizes using mobile Bluetooth sensors and examines to what extent this methodology represents a valuable alternative to existing traditional crowd density estimation methods. The proposed methodology is applied in a unique case study that uses Bluetooth technology for the mobile mapping of spectators of the Tour of Flanders 2011 road cycling race. The locations of nearly 16,000 cell phones of spectators along the race course were registered and detailed views of the spatiotemporal distribution of the crowd were generated. Comparison with visual head counts from camera footage delivered a detection ratio of 13.0 ± 2.3%, making it possible to estimate the crowd size. To our knowledge, this is the first study that uses mobile Bluetooth sensors to count and map a crowd over space and time. PMID:23202044

A Bluetooth/PDR Integration Algorithm for an Indoor Positioning System.

PubMed

Li, Xin; Wang, Jian; Liu, Chunyan

2015-09-25

This paper proposes two schemes for indoor positioning by fusing Bluetooth beacons and a pedestrian dead reckoning (PDR) technique to provide meter-level positioning without additional infrastructure. As to the PDR approach, a more effective multi-threshold step detection algorithm is used to improve the positioning accuracy. According to pedestrians' different walking patterns such as walking or running, this paper makes a comparative analysis of multiple step length calculation models to determine a linear computation model and the relevant parameters. In consideration of the deviation between the real heading and the value of the orientation sensor, a heading estimation method with real-time compensation is proposed, which is based on a Kalman filter with map geometry information. The corrected heading can inhibit the positioning error accumulation and improve the positioning accuracy of PDR. Moreover, this paper has implemented two positioning approaches integrated with Bluetooth and PDR. One is the PDR-based positioning method based on map matching and position correction through Bluetooth. There will not be too much calculation work or too high maintenance costs using this method. The other method is a fusion calculation method based on the pedestrians' moving status (direct movement or making a turn) to determine adaptively the noise parameters in an Extended Kalman Filter (EKF) system. This method has worked very well in the elimination of various phenomena, including the "go and back" phenomenon caused by the instability of the Bluetooth-based positioning system and the "cross-wall" phenomenon due to the accumulative errors caused by the PDR algorithm. Experiments performed on the fourth floor of the School of Environmental Science and Spatial Informatics (SESSI) building in the China University of Mining and Technology (CUMT) campus showed that the proposed scheme can reliably achieve a 2-meter precision.

A Bluetooth/PDR Integration Algorithm for an Indoor Positioning System

PubMed Central

Li, Xin; Wang, Jian; Liu, Chunyan

2015-01-01

This paper proposes two schemes for indoor positioning by fusing Bluetooth beacons and a pedestrian dead reckoning (PDR) technique to provide meter-level positioning without additional infrastructure. As to the PDR approach, a more effective multi-threshold step detection algorithm is used to improve the positioning accuracy. According to pedestrians’ different walking patterns such as walking or running, this paper makes a comparative analysis of multiple step length calculation models to determine a linear computation model and the relevant parameters. In consideration of the deviation between the real heading and the value of the orientation sensor, a heading estimation method with real-time compensation is proposed, which is based on a Kalman filter with map geometry information. The corrected heading can inhibit the positioning error accumulation and improve the positioning accuracy of PDR. Moreover, this paper has implemented two positioning approaches integrated with Bluetooth and PDR. One is the PDR-based positioning method based on map matching and position correction through Bluetooth. There will not be too much calculation work or too high maintenance costs using this method. The other method is a fusion calculation method based on the pedestrians’ moving status (direct movement or making a turn) to determine adaptively the noise parameters in an Extended Kalman Filter (EKF) system. This method has worked very well in the elimination of various phenomena, including the “go and back” phenomenon caused by the instability of the Bluetooth-based positioning system and the “cross-wall” phenomenon due to the accumulative errors caused by the PDR algorithm. Experiments performed on the fourth floor of the School of Environmental Science and Spatial Informatics (SESSI) building in the China University of Mining and Technology (CUMT) campus showed that the proposed scheme can reliably achieve a 2-meter precision. PMID:26404277

Overview and Evaluation of Bluetooth Low Energy: An Emerging Low-Power Wireless Technology

PubMed Central

Gomez, Carles; Oller, Joaquim; Paradells, Josep

2012-01-01

Bluetooth Low Energy (BLE) is an emerging low-power wireless technology developed for short-range control and monitoring applications that is expected to be incorporated into billions of devices in the next few years. This paper describes the main features of BLE, explores its potential applications, and investigates the impact of various critical parameters on its performance. BLE represents a trade-off between energy consumption, latency, piconet size, and throughput that mainly depends on parameters such as connInterval and connSlaveLatency. According to theoretical results, the lifetime of a BLE device powered by a coin cell battery ranges between 2.0 days and 14.1 years. The number of simultaneous slaves per master ranges between 2 and 5,917. The minimum latency for a master to obtain a sensor reading is 676 μs, although simulation results show that, under high bit error rate, average latency increases by up to three orders of magnitude. The paper provides experimental results that complement the theoretical and simulation findings, and indicates implementation constraints that may reduce BLE performance.

Effects of Bluetooth device electromagnetic field on hearing: pilot study.

PubMed

Balachandran, R; Prepageran, N; Prepagaran, N; Rahmat, O; Zulkiflee, A B; Hufaida, K S

2012-04-01

The Bluetooth wireless headset has been promoted as a 'hands-free' device with a low emission of electromagnetic radiation. To evaluate potential changes in hearing function as a consequence of using Bluetooth devices, by assessing changes in pure tone audiography and distortion production otoacoustic emissions. Prospective study. Thirty adult volunteers were exposed to a Bluetooth headset device (1) on 'standby' setting for 6 hours and (2) at full power for 10 minutes. Post-exposure hearing was evaluated using pure tone audiography and distortion production otoacoustic emission testing. There were no statistically significant changes in hearing, as measured above, following either exposure type. Exposure to the electromagnetic field emitted by a Bluetooth headset, as described above, did not decrease hearing thresholds or alter distortion product otoacoustic emissions.

Miniaturized module for the wireless transmission of measurements with Bluetooth.

PubMed

Roth, H; Schwaibold, M; Moor, C; Schöchlin, J; Bolz, A

2002-01-01

The wiring of patients for obtaining medical measurements has many disadvantages. In order to limit these, a miniaturized module was developed which digitalizes analog signals and sends the signal wirelessly to the receiver using Bluetooth. Bluetooth is especially suitable for this application because distances of up to 10 m are possible with low power consumption and robust transmission with encryption. The module consists of a Bluetooth chip, which is initialized in such a way by a microcontroller that connections from other bluetooth receivers can be accepted. The signals are then transmitted to the distant end. The maximum bit rate of the 23 mm x 30 mm module is 73.5 kBit/s. At 4.7 kBit/s, the current consumption is 12 mA.

A Bluetooth-Based Device Management Platform for Smart Sensor Environment

NASA Astrophysics Data System (ADS)

Lim, Ivan Boon-Kiat; Yow, Kin Choong

In this paper, we propose the use of Bluetooth as the device management platform for the various embedded sensors and actuators in an ambient intelligent environment. We demonstrate the ease of adding Bluetooth capability to common sensor circuits (e.g. motion sensor circuit based on a pyroelectric infrared (PIR) sensor). A central logic application is proposed which controls the operation of controller devices, based on values returned by sensors via Bluetooth. The operation of devices depends on rules that are learnt from user behavior using an Elman recurrent neural network. Overall, Bluetooth has shown its potential in being used as a device management platform in an ambient intelligent environment, which allows sensors and controllers to be deployed even in locations where power sources are not readily available, by using battery power.

A telemedicine system for wireless home healthcare based on Bluetooth and the Internet.

PubMed

Zhao, Xiaoming; Fei, Ding-Yu; Doarn, Charles R; Harnett, Brett; Merrell, Ronald

2004-01-01

The VitalPoll Telemedicine System (VTS) was designed and developed for wireless home healthcare. The aims of this study were: to design the architecture and communication methods for a telemedicine system; to implement a physiologic routing hub to collect data from different medical devices and sensors; and to evaluate the feasibility of this system for applications in wireless home healthcare. The VTS was built using Bluetooth wireless and Internet technologies with client/server architecture. Several medical devices, which acquire vital signs, such as real-time electrocardiogram signals, heart rate, body temperature, and activity (physical motion), were integrated into the VTS. Medical information and data were transmitted over short-range interface (USB, RS232), wireless communication, and the Internet. The medical results were stored in a database and presented using a web browser. The patient's vital signals can be collected, transmitted, and displayed in real time by the VTS. The experiments verified no data loss during Bluetooth and Internet communication. Bluetooth and the Internet provide enough bandwidth channels to tranmit these vital signs. The experimental results show that VTS may be suitable for a practical telemedicine system in home healthcare.

Measurement of the Mutual Interference Between Independent Bluetooth Devices

NASA Astrophysics Data System (ADS)

Schoof, Adrien; Ter Haseborg, Jan Luiken

In this paper the field superposition of commercial Bluetooth transmitters is examined. The superposition is measured for miscellaneous analyzer filter bandwidths, transmitter combinations and numbers. Also the commonness of the collisions is measured. Finally the spatial field distributions of standalone and Bluetooth equipped devices are measured and will be presented and discussed.

Bluetooth-based sensor networks for remotely monitoring the physiological signals of a patient.

PubMed

Zhang, Ying; Xiao, Hannan

2009-11-01

Integrating intelligent medical microsensors into a wireless communication network makes it possible to remotely collect physiological signals of a patient, release the patient from being tethered to monitoring medical instrumentations, and facilitate the patient's early hospital discharge. This can further improve life quality by providing continuous observation without the need of disrupting the patient's normal life, thus reducing the risk of infection significantly, and decreasing the cost of the hospital and the patient. This paper discusses the implementation issues, and describes the overall system architecture of our developed Bluetooth sensor network for patient monitoring and the corresponding heart activity sensors. It also presents our approach to developing the intelligent physiological sensor nodes involving integration of Bluetooth radio technology, hardware and software organization, and our solutions for onboard signal processing.

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings

PubMed Central

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices. PMID:22043254

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings.

PubMed

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices.

Bluetooth(Registered Trademark) Heart Rate Monitors for Spaceflight

NASA Technical Reports Server (NTRS)

Buxton, Roxanne E.; West, Michael R.; Kalogera, Kent L.; Hanson, Andrea M.

2016-01-01

Heart rate monitoring is required during exercise for crewmembers aboard the International Space Station (ISS) and will be for future exploration missions. The cardiovascular system must be sufficiently stressed throughout a mission to maintain the ability to perform nominal and contingency/emergency tasks. High quality heart rate data is required to accurately determine the intensity of exercise performed by the crewmembers and show maintenance of VO2max. The quality of the data collected on ISS is subject to multiple limitations and is insufficient to meet current requirements. PURPOSE: To evaluate the performance of commercially available Bluetooth® heart rate monitors (BT_HRM) and their ability to provide high quality heart rate data to monitor crew health on board ISS and during future exploration missions. METHODS: Nineteen subjects completed 30 data collection sessions of various intensities on the treadmill and/or cycle. Subjects wore several BT_HRM technologies for each testing session. One electrode-based chest strap (CS) was worn, while one or more optical sensors (OS) was worn. Subjects were instrumented with a 12-lead ECG to compare the heart rate data from the Bluetooth sensors. Each BT_RHM data set was time matched to the ECG data and a +/-5bpm threshold was applied to the difference between the two data sets. Percent error was calculated based on the number of data points outside the threshold and the total number of data points. REULTS: The electrode-based chest straps performed better than the optical sensors. The best performing CS was CS1 (1.6%error), followed by CS4 (3.3%error), CS3 (6.4%error), and CS2 (9.2%error). The OS resulted in 10.4% error for OS1 and 14.9% error for OS2. CONCLUSIONS: The highest quality data came from CS1, unfortunately it has been discontinued by the manufacturer. The optical sensors have not been ruled out for use, but more investigation is needed to determine how to get the best quality data. CS2 will be used in an

Consistent Steering System using SCTP for Bluetooth Scatternet Sensor Network

NASA Astrophysics Data System (ADS)

Dhaya, R.; Sadasivam, V.; Kanthavel, R.

2012-12-01

Wireless communication is the best way to convey information from source to destination with flexibility and mobility and Bluetooth is the wireless technology suitable for short distance. On the other hand a wireless sensor network (WSN) consists of spatially distributed autonomous sensors to cooperatively monitor physical or environmental conditions, such as temperature, sound, vibration, pressure, motion or pollutants. Using Bluetooth piconet wireless technique in sensor nodes creates limitation in network depth and placement. The introduction of Scatternet solves the network restrictions with lack of reliability in data transmission. When the depth of the network increases, it results in more difficulties in routing. No authors so far focused on the reliability factors of Scatternet sensor network's routing. This paper illustrates the proposed system architecture and routing mechanism to increase the reliability. The another objective is to use reliable transport protocol that uses the multi-homing concept and supports multiple streams to prevent head-of-line blocking. The results show that the Scatternet sensor network has lower packet loss even in the congestive environment than the existing system suitable for all surveillance applications.

Travel time estimation using Bluetooth.

DOT National Transportation Integrated Search

2015-06-01

The objective of this study was to investigate the feasibility of using a Bluetooth Probe Detection System (BPDS) to : estimate travel time in an urban area. Specifically, the study investigated the possibility of measuring overall congestion, the : ...

Design and implementation of a Bluetooth-based infant monitoring/saver (BIMS) system

NASA Astrophysics Data System (ADS)

Sonmez, Ahmet E.; Nalcaci, Murat T.; Pazarbasi, Mehmet A.; Toker, Onur; Fidanboylu, Kemal

2007-04-01

In this work, we discuss the design and implementation of a Bluetooth technology based infant monitoring system, which will enable the mother to monitor her baby's health condition remotely in real-time. The system will measure the heart rate, and temperature of the infant, and stream this data to the mother's Bluetooth based mobile unit, e.g. cell phone, PDA, etc. Existing infant monitors either require so many cables, or transmit only voice and/or video information, which is not enough for monitoring the health condition of an infant. With the proposed system, the mother will be warned against any abnormalities, which may be an indication of a disease, which in turn may result a sudden infant death. High temperature is a common symptom for several diseases, and heart rate is an essential sign of life, low or high heart rates are also essentials symptoms. Because of these reasons, the proposed system continously measures these two critical values. A 12 bits digital temperature sensor is used to measure infant's body temperature, and a piezo film sensor is used measure infant's heartbeat rate. These sensors, some simple analog circuitry, and a ToothPick unit are the main components of our embedded system. ToothPick unit is basically a Microchip 18LF6720 microcontroller, plus an RF circuitry with Bluetooth stack.

An Interactive Real-Time Locating System Based on Bluetooth Low-Energy Beacon Network †

PubMed Central

Lin, You-Wei

2018-01-01

The ubiquity of Bluetooth-enabled smartphones and peripherals has brought tremendous convenience to our daily life. In recent years, Bluetooth beacons have also been gaining popularity in implementing a variety of innovative location-based services such as self-guided systems in exhibition centers. However, the broadcast-based beacon technology can only provide unidirectional communication. In case smartphone users would like to respond to the beacon messages, they have to rely on their own mobile Internet connections to send the information back to the backend system. Nevertheless, mobile Internet services may not be always available or too costly. In this work, we develop a real-time locating system based only on the Bluetooth low energy (BLE) technology to support interactive communications by combining the broadcast and mesh topology options to extend the applicability of beacon solutions. Specifically, we turn the smartphone into a beacon device and augment the beacon devices with the capability of forming a mesh network. The implementation result shows that our beacon devices can detect the presence of specific users at specific locations, and then the presence state can be sent to the application server via the relay of beacon devices. Moreover, the application server can send personalized location-based messages to the users, again via the relay of beacon devices. With the capability of relaying messages between the beacon devices, it would be convenient for developers to implement a variety of interactive applications such as tracking VIP customers at the airport, or tracking an elder with Alzheimer’s disease in the neighborhood. PMID:29883386

An Interactive Real-Time Locating System Based on Bluetooth Low-Energy Beacon Network †.

PubMed

Lin, You-Wei; Lin, Chi-Yi

2018-05-21

The ubiquity of Bluetooth-enabled smartphones and peripherals has brought tremendous convenience to our daily life. In recent years, Bluetooth beacons have also been gaining popularity in implementing a variety of innovative location-based services such as self-guided systems in exhibition centers. However, the broadcast-based beacon technology can only provide unidirectional communication. In case smartphone users would like to respond to the beacon messages, they have to rely on their own mobile Internet connections to send the information back to the backend system. Nevertheless, mobile Internet services may not be always available or too costly. In this work, we develop a real-time locating system based only on the Bluetooth low energy (BLE) technology to support interactive communications by combining the broadcast and mesh topology options to extend the applicability of beacon solutions. Specifically, we turn the smartphone into a beacon device and augment the beacon devices with the capability of forming a mesh network. The implementation result shows that our beacon devices can detect the presence of specific users at specific locations, and then the presence state can be sent to the application server via the relay of beacon devices. Moreover, the application server can send personalized location-based messages to the users, again via the relay of beacon devices. With the capability of relaying messages between the beacon devices, it would be convenient for developers to implement a variety of interactive applications such as tracking VIP customers at the airport, or tracking an elder with Alzheimer’s disease in the neighborhood.

The Research and Implementation of Vehicle Bluetooth Hands-free Devices Key Parameters Downloading Algorithm

NASA Astrophysics Data System (ADS)

Zhang, Xiao-bo; Wang, Zhi-xue; Li, Jian-xin; Ma, Jian-hui; Li, Yang; Li, Yan-qiang

In order to facilitate Bluetooth function realization and information can be effectively tracked in the process of production, the vehicle Bluetooth hands-free devices need to download such key parameters as Bluetooth address, CVC license and base plate numbers, etc. Therefore, it is the aim to search simple and effective methods to download parameters for each vehicle Bluetooth hands-free device, and to control and record the use of parameters. In this paper, by means of Bluetooth Serial Peripheral Interface programmer device, the parallel port is switched to SPI. The first step is to download parameters is simulating SPI with the parallel port. To perform SPI function, operating the parallel port in accordance with the SPI timing. The next step is to achieve SPI data transceiver functions according to the programming parameters of options. Utilizing the new method, downloading parameters is fast and accurate. It fully meets vehicle Bluetooth hands-free devices production requirements. In the production line, it has played a large role.

An Empirical Study of the Transmission Power Setting for Bluetooth-Based Indoor Localization Mechanisms

PubMed Central

Castillo-Cara, Manuel; Lovón-Melgarejo, Jesús; Bravo-Rocca, Gusseppe; Orozco-Barbosa, Luis; García-Varea, Ismael

2017-01-01

Nowadays, there is a great interest in developing accurate wireless indoor localization mechanisms enabling the implementation of many consumer-oriented services. Among the many proposals, wireless indoor localization mechanisms based on the Received Signal Strength Indication (RSSI) are being widely explored. Most studies have focused on the evaluation of the capabilities of different mobile device brands and wireless network technologies. Furthermore, different parameters and algorithms have been proposed as a means of improving the accuracy of wireless-based localization mechanisms. In this paper, we focus on the tuning of the RSSI fingerprint to be used in the implementation of a Bluetooth Low Energy 4.0 (BLE4.0) Bluetooth localization mechanism. Following a holistic approach, we start by assessing the capabilities of two Bluetooth sensor/receiver devices. We then evaluate the relevance of the RSSI fingerprint reported by each BLE4.0 beacon operating at various transmission power levels using feature selection techniques. Based on our findings, we use two classification algorithms in order to improve the setting of the transmission power levels of each of the BLE4.0 beacons. Our main findings show that our proposal can greatly improve the localization accuracy by setting a custom transmission power level for each BLE4.0 beacon. PMID:28590413

An Empirical Study of the Transmission Power Setting for Bluetooth-Based Indoor Localization Mechanisms.

PubMed

Castillo-Cara, Manuel; Lovón-Melgarejo, Jesús; Bravo-Rocca, Gusseppe; Orozco-Barbosa, Luis; García-Varea, Ismael

2017-06-07

Nowadays, there is a great interest in developing accurate wireless indoor localization mechanisms enabling the implementation of many consumer-oriented services. Among the many proposals, wireless indoor localization mechanisms based on the Received Signal Strength Indication (RSSI) are being widely explored. Most studies have focused on the evaluation of the capabilities of different mobile device brands and wireless network technologies. Furthermore, different parameters and algorithms have been proposed as a means of improving the accuracy of wireless-based localization mechanisms. In this paper, we focus on the tuning of the RSSI fingerprint to be used in the implementation of a Bluetooth Low Energy 4.0 (BLE4.0) Bluetooth localization mechanism. Following a holistic approach, we start by assessing the capabilities of two Bluetooth sensor/receiver devices. We then evaluate the relevance of the RSSI fingerprint reported by each BLE4.0 beacon operating at various transmission power levels using feature selection techniques. Based on our findings, we use two classification algorithms in order to improve the setting of the transmission power levels of each of the BLE4.0 beacons. Our main findings show that our proposal can greatly improve the localization accuracy by setting a custom transmission power level for each BLE4.0 beacon.

Middleware Solutions for Self-organizing Multi-hop Multi-path Internet Connectivity Based on Bluetooth

NASA Astrophysics Data System (ADS)

Bellavista, Paolo; Giannelli, Carlo

The availability of heterogeneous wireless interfaces and of growing computing resources on widespread portable devices pushes for enabling innovative deployment scenarios where mobile nodes dynamically self-organize to offer Internet connectivity to their peers via dynamically established multi-hop multi-path opportunities. We claim the suitability of novel, mobility-aware, and application-layer middleware based on lightweight evaluation indicators to support the complexity of that scenario, involving heterogeneous wireless technologies over differentiated and statically unpredictable execution environments. To validate these claims, we have implemented an innovative middleware that manages the durability/throughput-aware formation and selection of different multi-hop paths simultaneously. This paper specifically focuses on how our middleware effectively exploits Bluetooth for multi-hop multi-path networking, by pointing out the crucial role of i) compliance with standard solutions to favor rapid deployment over off-the-shelf equipment and ii) the reduction of the usual overhead associated with some expensive Bluetooth operations, e.g., device inquiry. In particular, the paper shows how it is possible, on the one hand, to extend JSR-82 to portably access monitoring indicators for lightweight mobility/throughput estimations and, on the other hand, to reduce the time needed to update the set of available Bluetooth-based connectivity opportunities via approximated and lightweight forms of discovery.

Surveying the comfort perception of the ergonomic design of bluetooth earphones.

PubMed

Chiu, Hsiao-Ping; Chiang, Hsin-Yu; Liu, Chien-Hsiou; Wang, Ming-Hsu; Chiou, Wen-Ko

2014-01-01

Bluetooth earphones can facilitate communications among workers engaged in manual (e.g., professional driver)or visual tasks (e.g., security guard). If workers remove their Bluetooth earphones due to poor fit, then communication effectiveness will decline, especially during manual or visual tasks. (1) To identify which design properties of Bluetooth earphones can contribute to user comfort, and (2) to identify if person characteristics (i.e., gender and ear shapes in this study) are related to differences in comfort perception during earphone use. 198 participants were recruited for this study.Individuals used four models of Bluetooth earphones in randomized order while performing computer tasks and then completed questionnaires on comfort perception specifically designed for this study. The 2 × 3 × 4 mixed design analysis of variance (ANOVA) was conducted to investigate the effects of gender, ear shape, and model condition. The results indicated that there were significant differences in model on comfort perception. For earplugs, the shape of the earphone and the elasticity of material are important ergonomic concerns to improve the comfort perception. In addition, the adjustable tail length is an important ergonomic design property for the ear-hook. The information gained in this study should be useful in improving the ergonomic fitness of Bluetooth earphones.

Analysis of latency performance of bluetooth low energy (BLE) networks.

PubMed

Cho, Keuchul; Park, Woojin; Hong, Moonki; Park, Gisu; Cho, Wooseong; Seo, Jihoon; Han, Kijun

2014-12-23

Bluetooth Low Energy (BLE) is a short-range wireless communication technology aiming at low-cost and low-power communication. The performance evaluation of classical Bluetooth device discovery have been intensively studied using analytical modeling and simulative methods, but these techniques are not applicable to BLE, since BLE has a fundamental change in the design of the discovery mechanism, including the usage of three advertising channels. Recently, there several works have analyzed the topic of BLE device discovery, but these studies are still far from thorough. It is thus necessary to develop a new, accurate model for the BLE discovery process. In particular, the wide range settings of the parameters introduce lots of potential for BLE devices to customize their discovery performance. This motivates our study of modeling the BLE discovery process and performing intensive simulation. This paper is focused on building an analytical model to investigate the discovery probability, as well as the expected discovery latency, which are then validated via extensive experiments. Our analysis considers both continuous and discontinuous scanning modes. We analyze the sensitivity of these performance metrics to parameter settings to quantitatively examine to what extent parameters influence the performance metric of the discovery processes.

[Temperature Measurement with Bluetooth under Android Platform].

PubMed

Wang, Shuai; Shen, Hao; Luo, Changze

2015-03-01

To realize the real-time transmission of temperature data and display using the platform of intelligent mobile phone and bluetooth. Application of Arduino Uno R3 in temperature data acquisition of digital temperature sensor DS18B20 acquisition, through the HC-05 bluetooth transmits the data to the intelligent smart phone Android system, realizes transmission of temperature data. Using Java language to write applications program under Android development environment, can achieve real-time temperature data display, storage and drawing temperature fluctuations drawn graphics. Temperature sensor is experimentally tested to meet the body temperature measurement precision and accuracy. This paper can provide a reference for other smart phone mobile medical product development.

Determination of maternal pedigree and ewe-lamb spatial relationships by application of Bluetooth technology in extensive farming systems.

PubMed

Sohi, R; Trompf, J; Marriott, H; Bervan, A; Godoy, B I; Weerasinghe, M; Desai, A; Jois, M

2017-11-01

The objectives of this study were to validate the application of Bluetooth technology to determine maternal pedigree and to determine ewe-lamb spatial relationships in extensive farming systems. A total of 35 first-cross Merino ewes (Merino × Border Leicester and East Friesian) and 23 of their lambs aged 1 to 3 wk were fitted with activity monitors equipped with Bluetooth (BT) technology (ActiGraph wGT3X-BT) by means of halters and collars, respectively. The BT devices on lambs were programmed to receive wireless signals once every minute from nearby BT units on ewes, which were programmed as beacons sending BT signals 4 times every second. Ewes and lambs fitted with sensors were dispatched into the paddocks, and after 10 d, the sensor units were retrieved and the BT signals received by lambs were downloaded using the ActiGraph software. The maternal pedigree of the lambs was determined as the ewe from which the lamb received the most BT signals. The distance between the lamb receiving the signal and the ewe sending the signal was estimated from the strength of BT signal received. The pedigree determined by BT was compared with the pedigree determined by DNA profiling and verification. The results showed that the accuracy of maternal pedigree determined by BT signals reached 100% within the first 15 min of returning animals to pasture of ewes and lambs fitted with sensors. Maternal signals (counts/d) received by 1-, 2-, and 3-wk-old lambs were 617 ± 102, 603 ± 54, and 498 ± 36, respectively, and the corresponding nonmaternal signals received were 140 ± 27, 106 ± 30, and 155 ± 39, respectively. Maternal signals received during the dark period were significantly higher than the maternal signals received during the light period ( < 0.05). Maternal signals received during the light period by 3-wk-old lambs were significantly lower when compared with those received by 1- and 2-wk-old lambs. Over 90% of the BT signals received from within 2 m of the lamb were from

Smartphone-based integrated PDR/GPS/Bluetooth pedestrian location

NASA Astrophysics Data System (ADS)

Li, Xianghong; Wei, Dongyan; Lai, Qifeng; Xu, Ying; Yuan, Hong

2017-02-01

Typical indoor location method is fingerprint and traditional outdoor location system is GPS. Both of them are of poor accuracy and limited only for indoor or outdoor environments. As the smartphones are equipped with MEMS sensors, it means PDR can be widely used. In this paper, an algorithm of smartphone-based integrated PDR/GPS/Bluetooth for pedestrian location in the indoor/outdoor is proposed, which can be highly expected to realize seamless indoor/outdoor localization of the pedestrian. In addition, we also provide technologies to estimate orientation with Magnetometer and Gyroscope and detect context with output of sensors. The extensive experimental results show that the proposed algorithm can realize seamless indoor/outdoor localization.

A remote drip infusion monitoring system employing Bluetooth.

PubMed

Amano, Hikaru; Ogawa, Hidekuni; Maki, Hiromichi; Tsukamoto, Sosuke; Yonezawa, Yoshiharu; Caldwell, W Morton

2012-01-01

We have developed a remote drip infusion monitoring system for use in hospitals. The system consists of several infusion monitoring devices and a central monitor. The infusion monitoring device employing a Bluetooth module can detect the drip infusion rate and an empty infusion solution bag, and then these data are sent to the central monitor placed at the nurses' station via the Bluetooth. The central monitor receives the data from several infusion monitoring devices and then displays graphically them. Therefore, the developed system can monitor intensively the drip infusion situation of the several patients at the nurses' station.

Feasibility of Bluetooth Data as a Surrogate Measure of Vehicle Operations : Technical Summary

DOT National Transportation Integrated Search

2012-10-01

The widespread use of portable electronic devices among consumers has allowed new opportunities for traffic data collection. Many of these devices contain short-range Bluetooth radios in addition to other electronic equipment. The included Bluetooth ...

Creating wi-fi bluetooth mesh network for crisis management applications

NASA Astrophysics Data System (ADS)

Al-Tekreeti, Safa; Adams, Christopher; Al-Jawad, Naseer

2010-04-01

This paper proposes a wireless mesh network implementation consisting of both Wi-Fi Ad-Hoc networks as well as Bluetooth Piconet/Scatternet networks, organised in an energy and throughput efficient structure. This type of networks can be easily constructed for Crises management applications, for example in an Earthquake disaster. The motivation of this research is to form mesh network from the mass availability of WiFi and Bluetooth enabled electronic devices such as mobile phones and PC's that are normally present in most regions were major crises occurs. The target of this study is to achieve an effective solution that will enable Wi-Fi and/or Bluetooth nodes to seamlessly configure themselves to act as a bridge between their own network and that of the other network to achieve continuous routing for our proposed mesh networks.

Analysis of Latency Performance of Bluetooth Low Energy (BLE) Networks

PubMed Central

Cho, Keuchul; Park, Woojin; Hong, Moonki; Park, Gisu; Cho, Wooseong; Seo, Jihoon; Han, Kijun

2015-01-01

Bluetooth Low Energy (BLE) is a short-range wireless communication technology aiming at low-cost and low-power communication. The performance evaluation of classical Bluetooth device discovery have been intensively studied using analytical modeling and simulative methods, but these techniques are not applicable to BLE, since BLE has a fundamental change in the design of the discovery mechanism, including the usage of three advertising channels. Recently, there several works have analyzed the topic of BLE device discovery, but these studies are still far from thorough. It is thus necessary to develop a new, accurate model for the BLE discovery process. In particular, the wide range settings of the parameters introduce lots of potential for BLE devices to customize their discovery performance. This motivates our study of modeling the BLE discovery process and performing intensive simulation. This paper is focused on building an analytical model to investigate the discovery probability, as well as the expected discovery latency, which are then validated via extensive experiments. Our analysis considers both continuous and discontinuous scanning modes. We analyze the sensitivity of these performance metrics to parameter settings to quantitatively examine to what extent parameters influence the performance metric of the discovery processes. PMID:25545266

The benefits of using bluetooth accessories with hearing aids.

PubMed

Smith, Pauline; Davis, Adrian

2014-10-01

To investigate the benefits in reported outcomes after providing bluetooth accessories for established hearing aid users. Prospective observational study using validated quantitative outcome measures and detailed patient narrative before and two months after patients were provided with bluetooth accessories. Twelve patients with bilateral NHS hearing aids participated. They had a wide range of ages and hearing loss. After two months, 10 patients reported substantial additional benefit and kept the accessories; two returned them for various reasons. Statistically significant changes were seen in two validated outcome measures: the Glasgow Hearing Aid Benefit Profile and the International Outcome Inventory - Hearing Aids, but not in the Speech, Spatial and Qualities of Hearing Scale. Two notable benefits were reported: some described hearing the emotion and mood in a voice for the first time; others were amazed to report an improved ability to hear film or to hold conversations over the telephone. The provision of bluetooth accessories can give additional reported benefit for some patients - we need better knowledge about who benefits, and whether further support/training to individuals would make a difference.

Bluetooth Low Energy Mesh Networks: A Survey.

PubMed

Darroudi, Seyed Mahdi; Gomez, Carles

2017-06-22

Bluetooth Low Energy (BLE) has gained significant momentum. However, the original design of BLE focused on star topology networking, which limits network coverage range and precludes end-to-end path diversity. In contrast, other competing technologies overcome such constraints by supporting the mesh network topology. For these reasons, academia, industry, and standards development organizations have been designing solutions to enable BLE mesh networks. Nevertheless, the literature lacks a consolidated view on this emerging area. This paper comprehensively surveys state of the art BLE mesh networking. We first provide a taxonomy of BLE mesh network solutions. We then review the solutions, describing the variety of approaches that leverage existing BLE functionality to enable BLE mesh networks. We identify crucial aspects of BLE mesh network solutions and discuss their advantages and drawbacks. Finally, we highlight currently open issues.

Bluetooth Low Energy Mesh Networks: A Survey

PubMed Central

Darroudi, Seyed Mahdi; Gomez, Carles

2017-01-01

Bluetooth Low Energy (BLE) has gained significant momentum. However, the original design of BLE focused on star topology networking, which limits network coverage range and precludes end-to-end path diversity. In contrast, other competing technologies overcome such constraints by supporting the mesh network topology. For these reasons, academia, industry, and standards development organizations have been designing solutions to enable BLE mesh networks. Nevertheless, the literature lacks a consolidated view on this emerging area. This paper comprehensively surveys state of the art BLE mesh networking. We first provide a taxonomy of BLE mesh network solutions. We then review the solutions, describing the variety of approaches that leverage existing BLE functionality to enable BLE mesh networks. We identify crucial aspects of BLE mesh network solutions and discuss their advantages and drawbacks. Finally, we highlight currently open issues. PMID:28640183

Wearable dry sensors with bluetooth connection for use in remote patient monitoring systems.

PubMed

Gargiulo, Gaetano; Bifulco, Paolo; Cesarelli, Mario; Jin, Craig; McEwan, Alistair; van Schaik, Andre

2010-01-01

Cost reduction has become the primary theme of healthcare reforms globally. More providers are moving towards remote patient monitoring, which reduces the length of hospital stays and frees up their physicians and nurses for acute cases and helps them to tackle staff shortages. Physiological sensors are commonly used in many human specialties e.g. electrocardiogram (ECG) electrodes, for monitoring heart signals, and electroencephalogram (EEG) electrodes, for sensing the electrical activity of the brain, are the most well-known applications. Consequently there is a substantial unmet need for physiological sensors that can be simply and easily applied by the patient or primary carer, are comfortable to wear, can accurately sense parameters over long periods of time and can be connected to data recording systems using Bluetooth technology. We have developed a small, battery powered, user customizable portable monitor. This prototype is capable of recording three-axial body acceleration, skin temperature, and has up to four bio analogical front ends. Moreover, it is also able of continuous wireless transmission to any Bluetooth device including a PDA or a cellular phone. The bio-front end can use long-lasting dry electrodes or novel textile electrodes that can be embedded in clothes. The device can be powered by a standard mobile phone which has a Ni-MH 3.6 V battery, to sustain more than seven days continuous functioning when using the Bluetooth Sniff mode to reduce TX power. In this paper, we present some of the evaluation experiments of our wearable personal monitor device with a focus on ECG applications.

Measuring Soil Moisture using the Signal Strength of Buried Bluetooth Devices.

NASA Astrophysics Data System (ADS)

Hut, R.; Campbell, C. S.

2015-12-01

A low power bluetooth Low Energy (BLE) device is burried 20cm into the soil and a smartphone is placed on top of the soil to test if bluetooth signal strength can be related to soil moisture. The smartphone continuesly records and stores bluetooth signal strength of the device. The soil is artifcially wetted and drained. Results show a relation between BLE signal strength and soil moisture that could be used to measure soil moisture using these off-the-shelf consumer electronics. This opens the possibily to develop sensors that can be buried into the soil, possibly below the plow-line. These sensors can measure local parameters such as electric conductivity, ph, pressure, etc. Readings would be uploaded to a device on the surface using BLE. The signal strength of this BLE would be an (additional) measurement of soil moisture.

A fractional-N frequency synthesizer for WCDMA/Bluetooth/ZigBee applications

NASA Astrophysics Data System (ADS)

Chunyuan, Zhou; Guolin, Li; Chun, Zhang; Baoyong, Chi; Dongmei, Li; Zhihua, Wang

2009-07-01

A triple-mode fractional-N frequency synthesizer with a noise-filter voltage controlled oscillator (VCO) for WCDMA/Bluetooth/ZigBee applications has been implemented in 0.18-μm RF-CMOS technology. The proposed synthesizer achieves a good phase noise lower than -80 dBc/Hz in band and -115 dBc/Hz@1 MHz for the three modes, and only draws 21 mA from a 1.8 V supply. It has a high hardware sharing and a small size, only 1.5 × 1.4 mm2. The system architecture, circuit design, and measured results are also presented.

Note: Methodology for the analysis of Bluetooth gateways in an implemented scatternet.

PubMed

Etxaniz, J; Monje, P M; Aranguren, G

2014-03-01

This Note introduces a novel methodology to analyze the time performance of Bluetooth gateways in multi-hop networks, known as scatternets. The methodology is focused on distinguishing between the processing time and the time that each communication between nodes takes along an implemented scatternet. This technique is not only valid for Bluetooth networks but also for other wireless networks that offer access to their middleware in order to include beacons in the operation of the nodes. We show in this Note the results of the tests carried out on a Bluetooth scatternet in order to highlight the reliability and effectiveness of the methodology. The results also validate this technique showing convergence in the results when subtracting the time for the beacons from the delay measurements.

A Bluetooth Low Energy Indoor Positioning System with Channel Diversity, Weighted Trilateration and Kalman Filtering

PubMed Central

Cantón Paterna, Vicente; Paradells Aspas, Josep; Pérez Bullones, María Alejandra

2017-01-01

Indoor Positioning Systems (IPS) using Bluetooth Low Energy (BLE) technology are currently becoming real and available, which has made them grow in popularity and use. However, there are still plenty of challenges related to this technology, especially in terms of Received Signal Strength Indicator (RSSI) fluctuations due to the behaviour of the channels and the multipath effect, that lead to poor precision. In order to mitigate these effects, in this paper we propose and implement a real Indoor Positioning System based on Bluetooth Low Energy, that improves accuracy while reducing power consumption and costs. The three main proposals are: frequency diversity, Kalman filtering and a trilateration method what we have denominated “weighted trilateration”. The analysis of the results proves that all the proposals improve the precision of the system, which goes up to 1.82 m 90% of the time for a device moving in a middle-size room and 0.7 m for static devices. Furthermore, we have proved that the system is scalable and efficient in terms of cost and power consumption. The implemented approach allows using a very simple device (like a SensorTag) on the items to locate. The system enables a very low density of anchor points or references and with a precision better than existing solutions. PMID:29258195

A Bluetooth Low Energy Indoor Positioning System with Channel Diversity, Weighted Trilateration and Kalman Filtering.

PubMed

Cantón Paterna, Vicente; Calveras Augé, Anna; Paradells Aspas, Josep; Pérez Bullones, María Alejandra

2017-12-16

Indoor Positioning Systems (IPS) using Bluetooth Low Energy (BLE) technology are currently becoming real and available, which has made them grow in popularity and use. However, there are still plenty of challenges related to this technology, especially in terms of Received Signal Strength Indicator (RSSI) fluctuations due to the behaviour of the channels and the multipath effect, that lead to poor precision. In order to mitigate these effects, in this paper we propose and implement a real Indoor Positioning System based on Bluetooth Low Energy, that improves accuracy while reducing power consumption and costs. The three main proposals are: frequency diversity, Kalman filtering and a trilateration method what we have denominated "weighted trilateration". The analysis of the results proves that all the proposals improve the precision of the system, which goes up to 1.82 m 90% of the time for a device moving in a middle-size room and 0.7 m for static devices. Furthermore, we have proved that the system is scalable and efficient in terms of cost and power consumption. The implemented approach allows using a very simple device (like a SensorTag) on the items to locate. The system enables a very low density of anchor points or references and with a precision better than existing solutions.

A Middleware Based Approach to Dynamically Deploy Location Based Services onto Heterogeneous Mobile Devices Using Bluetooth in Indoor Environment

NASA Astrophysics Data System (ADS)

Sadhukhan, Pampa; Sen, Rijurekha; Das, Pradip K.

Several methods for providing location based service (LBS) to mobile devices in indoor environment using wireless technologies like WLAN, RFID and Bluetooth have been proposed, implemented and evaluated. However, most of them do not focus on heterogeneity of mobile platforms, memory constraint of mobile devices, the adaptability of client or device to the new services it discovers whenever it reaches a new location. In this paper, we have proposed a Middleware based approach of LBS provision in the indoor environment, where a Bluetooth enabled Base Station (BS) detects Bluetooth enabled mobile devices and pushes a proper client application only to those devices that belong to some registered subscriber of LBS. This dynamic deployment enables the mobile clients to access any new service without having preinstalled interface to that service beforehand and thus the client's memory consumption is reduced. Our proposed work also addresses the other issues like authenticating the clients before providing them LBSs and introducing paid services. We have evaluated its performance in term of file transfer time with respect to file size and throughput with respect to distance. Experimental results on service consumption time by the mobile client for different services are also presented.

An Indoor Location-Based Control System Using Bluetooth Beacons for IoT Systems.

PubMed

Huh, Jun-Ho; Seo, Kyungryong

2017-12-19

The indoor location-based control system estimates the indoor position of a user to provide the service he/she requires. The major elements involved in the system are the localization server, service-provision client, user application positioning technology. The localization server controls access of terminal devices (e.g., Smart Phones and other wireless devices) to determine their locations within a specified space first and then the service-provision client initiates required services such as indoor navigation and monitoring/surveillance. The user application provides necessary data to let the server to localize the devices or allow the user to receive various services from the client. The major technological elements involved in this system are indoor space partition method, Bluetooth 4.0, RSSI (Received Signal Strength Indication) and trilateration. The system also employs the BLE communication technology when determining the position of the user in an indoor space. The position information obtained is then used to control a specific device(s). These technologies are fundamental in achieving a "Smart Living". An indoor location-based control system that provides services by estimating user's indoor locations has been implemented in this study (First scenario). The algorithm introduced in this study (Second scenario) is effective in extracting valid samples from the RSSI dataset but has it has some drawbacks as well. Although we used a range-average algorithm that measures the shortest distance, there are some limitations because the measurement results depend on the sample size and the sample efficiency depends on sampling speeds and environmental changes. However, the Bluetooth system can be implemented at a relatively low cost so that once the problem of precision is solved, it can be applied to various fields.

An Indoor Location-Based Control System Using Bluetooth Beacons for IoT Systems

PubMed Central

Huh, Jun-Ho; Seo, Kyungryong

2017-01-01

The indoor location-based control system estimates the indoor position of a user to provide the service he/she requires. The major elements involved in the system are the localization server, service-provision client, user application positioning technology. The localization server controls access of terminal devices (e.g., Smart Phones and other wireless devices) to determine their locations within a specified space first and then the service-provision client initiates required services such as indoor navigation and monitoring/surveillance. The user application provides necessary data to let the server to localize the devices or allow the user to receive various services from the client. The major technological elements involved in this system are indoor space partition method, Bluetooth 4.0, RSSI (Received Signal Strength Indication) and trilateration. The system also employs the BLE communication technology when determining the position of the user in an indoor space. The position information obtained is then used to control a specific device(s). These technologies are fundamental in achieving a “Smart Living”. An indoor location-based control system that provides services by estimating user’s indoor locations has been implemented in this study (First scenario). The algorithm introduced in this study (Second scenario) is effective in extracting valid samples from the RSSI dataset but has it has some drawbacks as well. Although we used a range-average algorithm that measures the shortest distance, there are some limitations because the measurement results depend on the sample size and the sample efficiency depends on sampling speeds and environmental changes. However, the Bluetooth system can be implemented at a relatively low cost so that once the problem of precision is solved, it can be applied to various fields. PMID:29257044

Toward a Robust Security Paradigm for Bluetooth Low Energy-Based Smart Objects in the Internet-of-Things.

PubMed

Cha, Shi-Cho; Yeh, Kuo-Hui; Chen, Jyun-Fu

2017-10-14

Bluetooth Low Energy (BLE) has emerged as one of the most promising technologies to enable the Internet-of-Things (IoT) paradigm. In BLE-based IoT applications, e.g., wearables-oriented service applications, the Bluetooth MAC addresses of devices will be swapped for device pairings. The random address technique is adopted to prevent malicious users from tracking the victim's devices with stationary Bluetooth MAC addresses and accordingly the device privacy can be preserved. However, there exists a tradeoff between privacy and security in the random address technique. That is, when device pairing is launched and one device cannot actually identify another one with addresses, it provides an opportunity for malicious users to break the system security via impersonation attacks. Hence, using random addresses may lead to higher security risks. In this study, we point out the potential risk of using random address technique and then present critical security requirements for BLE-based IoT applications. To fulfill the claimed requirements, we present a privacy-aware mechanism, which is based on elliptic curve cryptography, for secure communication and access-control among BLE-based IoT objects. Moreover, to ensure the security of smartphone application associated with BLE-based IoT objects, we construct a Smart Contract-based Investigation Report Management framework (SCIRM) which enables smartphone application users to obtain security inspection reports of BLE-based applications of interest with smart contracts.

Opportunistic Sensor Data Collection with Bluetooth Low Energy

PubMed Central

Aguilar, Sergio; Vidal, Rafael; Gomez, Carles

2017-01-01

Bluetooth Low Energy (BLE) has gained very high momentum, as witnessed by its widespread presence in smartphones, wearables and other consumer electronics devices. This fact can be leveraged to carry out opportunistic sensor data collection (OSDC) in scenarios where a sensor node cannot communicate with infrastructure nodes. In such cases, a mobile entity (e.g., a pedestrian or a vehicle) equipped with a BLE-enabled device can collect the data obtained by the sensor node when both are within direct communication range. In this paper, we characterize, both analytically and experimentally, the performance and trade-offs of BLE as a technology for OSDC, for the two main identified approaches, and considering the impact of its most crucial configuration parameters. Results show that a BLE sensor node running on a coin cell battery can achieve a lifetime beyond one year while transferring around 10 Mbit/day, in realistic OSDC scenarios. PMID:28124987

Opportunistic Sensor Data Collection with Bluetooth Low Energy.

PubMed

Aguilar, Sergio; Vidal, Rafael; Gomez, Carles

2017-01-23

Bluetooth Low Energy (BLE) has gained very high momentum, as witnessed by its widespread presence in smartphones, wearables and other consumer electronics devices. This fact can be leveraged to carry out opportunistic sensor data collection (OSDC) in scenarios where a sensor node cannot communicate with infrastructure nodes. In such cases, a mobile entity (e.g., a pedestrian or a vehicle) equipped with a BLE-enabled device can collect the data obtained by the sensor node when both are within direct communication range. In this paper, we characterize, both analytically and experimentally, the performance and trade-offs of BLE as a technology for OSDC, for the two main identified approaches, and considering the impact of its most crucial configuration parameters. Results show that a BLE sensor node running on a coin cell battery can achieve a lifetime beyond one year while transferring around 10 Mbit/day, in realistic OSDC scenarios.

The difference of delay time in monitoring system of facial acupressure learning media using bluetooth, wireless and ethernet

NASA Astrophysics Data System (ADS)

Agustin, Eny Widhia; Hangga, Arimaz; Fahrian, Muhammad Iqbal; Azhari, Anis Fikri

2018-03-01

The implementation of monitoring system in the facial acupressure learning media could increase the students' proficiency. However the common learning media still has not implemented a monitoring system in their learning process. This research was conducted to implement monitoring system in the mannequin head prototype as a learning media of facial acupressure using Bluetooth, wireless and Ethernet. The results of the implementation of monitoring system in the prototype showed that there were differences in the delay time between Bluetooth and wireless or Ethernet. The results data showed no difference in the average delay time between the use of Bluetooth with wireless and the use of Bluetooth with Ethernet in monitoring system of facial acupressure learning media. From all the facial acupressure points, the forehead facial acupressure point has the longest delay time of 11.93 seconds. The average delay time in all 3 class rooms was 1.96 seconds therefore the use of Bluetooth, wireless and Ethernet is highly recommended in the monitoring system of facial acupressure.

Bluetooth telemedicine processor for multichannel biomedical signal transmission via mobile cellular networks.

PubMed

Rasid, Mohd Fadlee A; Woodward, Bryan

2005-03-01

One of the emerging issues in m-Health is how best to exploit the mobile communications technologies that are now almost globally available. The challenge is to produce a system to transmit a patient's biomedical signals directly to a hospital for monitoring or diagnosis, using an unmodified mobile telephone. The paper focuses on the design of a processor, which samples signals from sensors on the patient. It then transmits digital data over a Bluetooth link to a mobile telephone that uses the General Packet Radio Service. The modular design adopted is intended to provide a "future-proofed" system, whose functionality may be upgraded by modifying the software.

Toward a Robust Security Paradigm for Bluetooth Low Energy-Based Smart Objects in the Internet-of-Things

PubMed Central

Cha, Shi-Cho; Chen, Jyun-Fu

2017-01-01

Bluetooth Low Energy (BLE) has emerged as one of the most promising technologies to enable the Internet-of-Things (IoT) paradigm. In BLE-based IoT applications, e.g., wearables-oriented service applications, the Bluetooth MAC addresses of devices will be swapped for device pairings. The random address technique is adopted to prevent malicious users from tracking the victim’s devices with stationary Bluetooth MAC addresses and accordingly the device privacy can be preserved. However, there exists a tradeoff between privacy and security in the random address technique. That is, when device pairing is launched and one device cannot actually identify another one with addresses, it provides an opportunity for malicious users to break the system security via impersonation attacks. Hence, using random addresses may lead to higher security risks. In this study, we point out the potential risk of using random address technique and then present critical security requirements for BLE-based IoT applications. To fulfill the claimed requirements, we present a privacy-aware mechanism, which is based on elliptic curve cryptography, for secure communication and access-control among BLE-based IoT objects. Moreover, to ensure the security of smartphone application associated with BLE-based IoT objects, we construct a Smart Contract-based Investigation Report Management framework (SCIRM) which enables smartphone application users to obtain security inspection reports of BLE-based applications of interest with smart contracts. PMID:29036900

Design and implementation of a telemedicine system using Bluetooth protocol and GSM/GPRS network, for real time remote patient monitoring.

PubMed

Jasemian, Yousef; Nielsen, Lars Arendt

2005-01-01

This paper introduces the design and implementation of a generic wireless and Real-time Multi-purpose Health Care Telemedicine system applying Bluetooth protocol, Global System for Mobile Communications (GSM) and General Packet Radio Service (GPRS). The paper explores the factors that should be considered when evaluating different technologies for application in telemedicine system. The design and implementation of an embedded wireless communication platform utilising Bluetooth protocol is described, and the implementation problems and limitations are investigated. The system is tested and its telecommunication general aspects are verified. The results showed that the system has (97.9 +/- 1.3)% Up-time, 2.5 x 10(-5) Bit Error Rate, 1% Dropped Call Rate, 97.4% Call Success Rate, 5 second transmission delay in average, (3.42 +/- 0.11) kbps throughput, and the system may have application in electrocardiography.

Bluetooth Communication Interface for EEG Signal Recording in Hyperbaric Chambers.

PubMed

Pastena, Lucio; Formaggio, Emanuela; Faralli, Fabio; Melucci, Massimo; Rossi, Marco; Gagliardi, Riccardo; Ricciardi, Lucio; Storti, Silvia F

2015-07-01

Recording biological signals inside a hyperbaric chamber poses technical challenges (the steel walls enclosing it greatly attenuate or completely block the signals as in a Faraday cage), practical (lengthy cables creating eddy currents), and safety (sparks hazard from power supply to the electronic apparatus inside the chamber) which can be overcome with new wireless technologies. In this technical report we present the design and implementation of a Bluetooth system for electroencephalographic (EEG) recording inside a hyperbaric chamber and describe the feasibility of EEG signal transmission outside the chamber. Differently from older systems, this technology allows the online recording of amplified signals, without interference from eddy currents. In an application of this technology, we measured EEG activity in professional divers under three experimental conditions in a hyperbaric chamber to determine how oxygen, assumed at a constant hyperbaric pressure of 2.8 ATA , affects the bioelectrical activity. The EEG spectral power estimated by fast Fourier transform and the cortical sources of the EEG rhythms estimated by low-resolution brain electromagnetic analysis were analyzed in three different EEG acquisitions: breathing air at sea level; breathing oxygen at a simulated depth of 18 msw, and breathing air at sea level after decompression.

An indoor positioning technology in the BLE mobile payment system

NASA Astrophysics Data System (ADS)

Han, Tiantian; Ding, Lei

2017-05-01

Mobile payment system for large supermarkets, the core function is through the BLE low-power Bluetooth technology to achieve the amount of payment in the mobile payment system, can through an indoor positioning technology to achieve value-added services. The technology by collecting Bluetooth RSSI, the fingerprint database of sampling points corresponding is established. To get Bluetooth module RSSI by the AP. Then, to use k-Nearest Neighbor match the value of the fingerprint database. Thereby, to help businesses find customers through the mall location, combined settlement amount of the customer's purchase of goods, to analyze customer's behavior. When the system collect signal strength, the distribution of the sampling points of RSSI is analyzed and the value is filtered. The system, used in the laboratory is designed to demonstrate the feasibility.

Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

NASA Astrophysics Data System (ADS)

Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao

With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration.

A novel algorithm for Bluetooth ECG.

PubMed

Pandya, Utpal T; Desai, Uday B

2012-11-01

In wireless transmission of ECG, data latency will be significant when battery power level and data transmission distance are not maintained. In applications like home monitoring or personalized care, to overcome the joint effect of previous issues of wireless transmission and other ECG measurement noises, a novel filtering strategy is required. Here, a novel algorithm, identified as peak rejection adaptive sampling modified moving average (PRASMMA) algorithm for wireless ECG is introduced. This algorithm first removes error in bit pattern of received data if occurred in wireless transmission and then removes baseline drift. Afterward, a modified moving average is implemented except in the region of each QRS complexes. The algorithm also sets its filtering parameters according to different sampling rate selected for acquisition of signals. To demonstrate the work, a prototyped Bluetooth-based ECG module is used to capture ECG with different sampling rate and in different position of patient. This module transmits ECG wirelessly to Bluetooth-enabled devices where the PRASMMA algorithm is applied on captured ECG. The performance of PRASMMA algorithm is compared with moving average and S-Golay algorithms visually as well as numerically. The results show that the PRASMMA algorithm can significantly improve the ECG reconstruction by efficiently removing the noise and its use can be extended to any parameters where peaks are importance for diagnostic purpose.

Effect of a Bluetooth-implemented hearing aid on speech recognition performance: subjective and objective measurement.

PubMed

Kim, Min-Beom; Chung, Won-Ho; Choi, Jeesun; Hong, Sung Hwa; Cho, Yang-Sun; Park, Gyuseok; Lee, Sangmin

2014-06-01

The object was to evaluate speech perception improvement through Bluetooth-implemented hearing aids in hearing-impaired adults. Thirty subjects with bilateral symmetric moderate sensorineural hearing loss participated in this study. A Bluetooth-implemented hearing aid was fitted unilaterally in all study subjects. Objective speech recognition score and subjective satisfaction were measured with a Bluetooth-implemented hearing aid to replace the acoustic connection from either a cellular phone or a loudspeaker system. In each system, participants were assigned to 4 conditions: wireless speech signal transmission into hearing aid (wireless mode) in quiet or noisy environment and conventional speech signal transmission using external microphone of hearing aid (conventional mode) in quiet or noisy environment. Also, participants completed questionnaires to investigate subjective satisfaction. Both cellular phone and loudspeaker system situation, participants showed improvements in sentence and word recognition scores with wireless mode compared to conventional mode in both quiet and noise conditions (P < .001). Participants also reported subjective improvements, including better sound quality, less noise interference, and better accuracy naturalness, when using the wireless mode (P < .001). Bluetooth-implemented hearing aids helped to improve subjective and objective speech recognition performances in quiet and noisy environments during the use of electronic audio devices.

Model-Based Localization and Tracking Using Bluetooth Low-Energy Beacons

PubMed Central

Cemgil, Ali Taylan

2017-01-01

We introduce a high precision localization and tracking method that makes use of cheap Bluetooth low-energy (BLE) beacons only. We track the position of a moving sensor by integrating highly unreliable and noisy BLE observations streaming from multiple locations. A novel aspect of our approach is the development of an observation model, specifically tailored for received signal strength indicator (RSSI) fingerprints: a combination based on the optimal transport model of Wasserstein distance. The tracking results of the entire system are compared with alternative baseline estimation methods, such as nearest neighboring fingerprints and an artificial neural network. Our results show that highly accurate estimation from noisy Bluetooth data is practically feasible with an observation model based on Wasserstein distance interpolation combined with the sequential Monte Carlo (SMC) method for tracking. PMID:29109375

Model-Based Localization and Tracking Using Bluetooth Low-Energy Beacons.

PubMed

Daniş, F Serhan; Cemgil, Ali Taylan

2017-10-29

We introduce a high precision localization and tracking method that makes use of cheap Bluetooth low-energy (BLE) beacons only. We track the position of a moving sensor by integrating highly unreliable and noisy BLE observations streaming from multiple locations. A novel aspect of our approach is the development of an observation model, specifically tailored for received signal strength indicator (RSSI) fingerprints: a combination based on the optimal transport model of Wasserstein distance. The tracking results of the entire system are compared with alternative baseline estimation methods, such as nearest neighboring fingerprints and an artificial neural network. Our results show that highly accurate estimation from noisy Bluetooth data is practically feasible with an observation model based on Wasserstein distance interpolation combined with the sequential Monte Carlo (SMC) method for tracking.

A combinatorial model of malware diffusion via bluetooth connections.

PubMed

Merler, Stefano; Jurman, Giuseppe

2013-01-01

We outline here the mathematical expression of a diffusion model for cellphones malware transmitted through Bluetooth channels. In particular, we provide the deterministic formula underlying the proposed infection model, in its equivalent recursive (simple but computationally heavy) and closed form (more complex but efficiently computable) expression.

Design and implementation of a bluetooth-based band-aid pulse rate sensor

NASA Astrophysics Data System (ADS)

Kumar, Prashanth S.; Oh, Sechang; Rai, Pratyush; Kwon, Hyeokjun; Banerjee, Nilanjan; Varadan, Vijay K.

2011-04-01

Remote patient monitoring systems capable of collecting vital patient data such as blood pressure readings, Electrocardiograph (ECG) waveforms, and heart rate can obviate the need for repeated visits to the hospital. Moreover, such systems that continuously monitor the human physiology can provide valuable data to prognosticate the onset of critical health problems. The key to such remote health diagnostics is the design of minimally intrusive, low cost sensors that do not impede a patient's quotidian life but at the same time collect reliable noise free data. To this end, in this paper, we design and implement a Bluetooth-based wireless sensor system with a disposable sensor element and a reusable wireless component that can be worn as a "band-aid". The sensor is a piezoelectric polymer film placed on the wrist in proximity to the radial artery. The band-aid sized sensor allows non-intrusive monitoring of the pulsatile flow of blood in the artery. The sensor, using the Bluetooth module, can communicate with any Bluetooth enabled computer, mobile phone, or PDA. The data collected from the patient can be remotely viewed and analyzed by a physician.

A system for ubiquitous health monitoring in the bedroom via a Bluetooth network and wireless LAN.

PubMed

Choi, J M; Choi, B H; Seo, J W; Sohn, R H; Ryu, M S; Yi, W; Park, K S

2004-01-01

Advances in information technology have enabled ubiquitous health monitoring at home, which is particularly useful for patients, who have to live alone. We have focused on the automatic and unobtrusive measurement of biomedical signals and activities of patients. We have constructed wireless communication networks in order to transfer data. The networks consist of Bluetooth and Wireless Local Area Network (WLAN). In this paper, we present the concept of a ubiquitous-Bedroom (u-Bedroom) which is a part of a ubiquitous-House (u-House) and we present our systems for ubiquitous health monitoring.

SEMICONDUCTOR INTEGRATED CIRCUITS: A reconfigurable analog baseband circuit for WLAN, WCDMA, and Bluetooth

NASA Astrophysics Data System (ADS)

Tao, Tong; Baoyong, Chi; Ziqiang, Wang; Ying, Zhang; Hanjun, Jiang; Zhihua, Wang

2010-05-01

A reconfigurable analog baseband circuit for WLAN, WCDMA, and Bluetooth in 0.35 μm CMOS is presented. The circuit consists of two variable gain amplifiers (VGA) in cascade and a Gm-C elliptic low-pass filter (LPF). The filter-order and the cut-off frequency of the LPF can be reconfigured to satisfy the requirements of various applications. In order to achieve the optimum power consumption, the bandwidth of the VGAs can also be dynamically reconfigured and some Gm cells can be cut off in the given application. Simulation results show that the analog baseband circuit consumes 16.8 mW for WLAN, 8.9 mW for WCDMA and only 6.5 mW for Bluetooth, all with a 3 V power supply. The analog baseband circuit could provide -10 to +40 dB variable gain, third-order low pass filtering with 1 MHz cut-off frequency for Bluetooth, fourth-order low pass filtering with 2.2 MHz cut-off frequency for WCDMA, and fifth-order low pass filtering with 11 MHz cut-off frequency for WLAN, respectively.

A Combinatorial Model of Malware Diffusion via Bluetooth Connections

PubMed Central

Merler, Stefano; Jurman, Giuseppe

2013-01-01

We outline here the mathematical expression of a diffusion model for cellphones malware transmitted through Bluetooth channels. In particular, we provide the deterministic formula underlying the proposed infection model, in its equivalent recursive (simple but computationally heavy) and closed form (more complex but efficiently computable) expression. PMID:23555677

[An integrated system of blood pressure measurement with bluetooth communication].

PubMed

Wang, Wei; Wang, Jing; Sun, Hongyang; Xu, Zuyang; Chai, Xinyu

2012-07-01

The development of the integrated blood pressure system with bluetooth communication function is introduced. Experimental results show that the system can complete blood pressure measurement and data transmission wireless effectively, which can be used in m-Health in future.

An Optimization Approach to Coexistence of Bluetooth and Wi-Fi Networks Operating in ISM Environment

NASA Astrophysics Data System (ADS)

Klajbor, Tomasz; Rak, Jacek; Wozniak, Jozef

Unlicensed ISM band is used by various wireless technologies. Therefore, issues related to ensuring the required efficiency and quality of operation of coexisting networks become essential. The paper addresses the problem of mutual interferences between IEEE 802.11b transmitters (commercially named Wi-Fi) and Bluetooth (BT) devices.An optimization approach to modeling the topology of BT scatternets is introduced, resulting in more efficient utilization of ISM environment consisting of BT and Wi-Fi networks. To achieve it, the Integer Linear Programming approach has been proposed. Example results presented in the paper illustrate significant benefits of using the proposed modeling strategy.

Effect of Bluetooth headset and mobile phone electromagnetic fields on the human auditory nerve.

PubMed

Mandalà, Marco; Colletti, Vittorio; Sacchetto, Luca; Manganotti, Paolo; Ramat, Stefano; Marcocci, Alessandro; Colletti, Liliana

2014-01-01

The possibility that long-term mobile phone use increases the incidence of astrocytoma, glioma and acoustic neuroma has been investigated in several studies. Recently, our group showed that direct exposure (in a surgical setting) to cell phone electromagnetic fields (EMFs) induces deterioration of auditory evoked cochlear nerve compound action potential (CNAP) in humans. To verify whether the use of Bluetooth devices reduces these effects, we conducted the present study with the same experimental protocol. Randomized trial. Twelve patients underwent retrosigmoid vestibular neurectomy to treat definite unilateral Ménière's disease while being monitored with acoustically evoked CNAPs to assess direct mobile phone exposure or alternatively the EMF effects of Bluetooth headsets. We found no short-term effects of Bluetooth EMFs on the auditory nervous structures, whereas direct mobile phone EMF exposure confirmed a significant decrease in CNAPs amplitude and an increase in latency in all subjects. The outcomes of the present study show that, contrary to the finding that the latency and amplitude of CNAPs are very sensitive to EMFs produced by the tested mobile phone, the EMFs produced by a common Bluetooth device do not induce any significant change in cochlear nerve activity. The conditions of exposure, therefore, differ from those of everyday life, in which various biological tissues may reduce the EMF affecting the cochlear nerve. Nevertheless, these novel findings may have important safety implications. © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

Bluetooth based chaos synchronization using particle swarm optimization and its applications to image encryption.

PubMed

Yau, Her-Terng; Hung, Tzu-Hsiang; Hsieh, Chia-Chun

2012-01-01

This study used the complex dynamic characteristics of chaotic systems and Bluetooth to explore the topic of wireless chaotic communication secrecy and develop a communication security system. The PID controller for chaos synchronization control was applied, and the optimum parameters of this PID controller were obtained using a Particle Swarm Optimization (PSO) algorithm. Bluetooth was used to realize wireless transmissions, and a chaotic wireless communication security system was developed in the design concept of a chaotic communication security system. The experimental results show that this scheme can be used successfully in image encryption.

Feasibility of Bluetooth Data as a Surrogate Measure of Vehicle Operations

DOT National Transportation Integrated Search

2012-10-01

This research was designed as proof-of-concept study to investigate how Bluetooth data loggers can be used to collect vehicle : operational data over traditional vehicle counting methods. The reliability test included mapping areas for five antenna o...

A wearable bluetooth LE sensor for patient monitoring during MRI scans.

PubMed

Vogt, Christian; Reber, Jonas; Waltisberg, Daniel; Buthe, Lars; Marjanovic, Josip; Munzenrieder, Niko; Pruessmann, Klaas P; Troster, Gerhard

2016-08-01

This paper presents a working prototype of a wearable patient monitoring device capable of recording the heart rate, blood oxygen saturation, surface temperature and humidity during an magnetic resonance imaging (MRI) experiment. The measured values are transmitted via Bluetooth low energy (LE) and displayed in real time on a smartphone on the outside of the MRI room. During 7 MRI image acquisitions of at least 1 min and a total duration of 25 min no Bluetooth data packets were lost. The raw measurements of the light intensity for the photoplethysmogram based heart rate measurement shows an increased noise floor by 50LSB (least significant bit) during the MRI operation, whereas the temperature and humidity readings are unaffected. The device itself creates a magnetic resonance (MR) signal loss with a radius of 14 mm around the device surface and shows no significant increase in image noise of an acquired MRI image due to its radio frequency activity. This enables continuous and unobtrusive patient monitoring during MRI scans.

Using Bluetooth proximity sensing to determine where office workers spend time at work.

PubMed

Clark, Bronwyn K; Winkler, Elisabeth A; Brakenridge, Charlotte L; Trost, Stewart G; Healy, Genevieve N

2018-01-01

Most wearable devices that measure movement in workplaces cannot determine the context in which people spend time. This study examined the accuracy of Bluetooth sensing (10-second intervals) via the ActiGraph GT9X Link monitor to determine location in an office setting, using two simple, bespoke algorithms. For one work day (mean±SD 6.2±1.1 hours), 30 office workers (30% men, aged 38±11 years) simultaneously wore chest-mounted cameras (video recording) and Bluetooth-enabled monitors (initialised as receivers) on the wrist and thigh. Additional monitors (initialised as beacons) were placed in the entry, kitchen, photocopy room, corridors, and the wearer's office. Firstly, participant presence/absence at each location was predicted from the presence/absence of signals at that location (ignoring all other signals). Secondly, using the information gathered at multiple locations simultaneously, a simple heuristic model was used to predict at which location the participant was present. The Bluetooth-determined location for each algorithm was tested against the camera in terms of F-scores. When considering locations individually, the accuracy obtained was excellent in the office (F-score = 0.98 and 0.97 for thigh and wrist positions) but poor in other locations (F-score = 0.04 to 0.36), stemming primarily from a high false positive rate. The multi-location algorithm exhibited high accuracy for the office location (F-score = 0.97 for both wear positions). It also improved the F-scores obtained in the remaining locations, but not always to levels indicating good accuracy (e.g., F-score for photocopy room ≈0.1 in both wear positions). The Bluetooth signalling function shows promise for determining where workers spend most of their time (i.e., their office). Placing beacons in multiple locations and using a rule-based decision model improved classification accuracy; however, for workplace locations visited infrequently or with considerable movement, accuracy was below

A low-cost biomedical signal transceiver based on a Bluetooth wireless system.

PubMed

Fazel-Rezai, Reza; Pauls, Mark; Slawinski, David

2007-01-01

Most current wireless biomedical signal transceivers use range-limiting communication. This work presents a low-cost biomedical signal transceiver that uses Bluetooth wireless technology. The design is implemented in a modular form to be adaptable to different types of biomedical signals. The signal front end obtains and processes incoming signals, which are then transmitted via a microcontroller and wireless module. Near real-time receive software in LabVIEW was developed to demonstrate the system capability. The completed transmitter prototype successfully transmits ECG signals, and is able to simultaneously send multiple signals. The sampling rate of the transmitter is fast enough to send up to thirteen ECG signals simultaneously, with an error rate below 0.1% for transmission exceeding 65 meters. A low-cost wireless biomedical transceiver has many applications, such as real-time monitoring of patients with a known condition in non-clinical settings.

State of the Art, Trends and Future of Bluetooth Low Energy, Near Field Communication and Visible Light Communication in the Development of Smart Cities.

PubMed

Cerruela García, Gonzalo; Luque Ruiz, Irene; Gómez-Nieto, Miguel Ángel

2016-11-23

The current social impact of new technologies has produced major changes in all areas of society, creating the concept of a smart city supported by an electronic infrastructure, telecommunications and information technology. This paper presents a review of Bluetooth Low Energy (BLE), Near Field Communication (NFC) and Visible Light Communication (VLC) and their use and influence within different areas of the development of the smart city. The document also presents a review of Big Data Solutions for the management of information and the extraction of knowledge in an environment where things are connected by an "Internet of Things" (IoT) network. Lastly, we present how these technologies can be combined together to benefit the development of the smart city.

Design and construction of a desktop AC susceptometer using an Arduino and a Bluetooth for serial interface

NASA Astrophysics Data System (ADS)

Pérez, Israel; Ángel Hernández Cuevas, José; Trinidad Elizalde Galindo, José

2018-05-01

We designed and developed a desktop AC susceptometer for the characterization of materials. The system consists of a lock-in amplifier, an AC function generator, a couple of coils, a sample holder, a computer system with a designed software in freeware C++ code, and an Arduino card coupled to a Bluetooth module. The Arduino/Bluetooth serial interface allows the user to have a connection to almost any computer and thus avoids the problem of connectivity between the computer and the peripherals, such as the lock-in amplifier and the function generator. The Bluetooth transmitter/receiver used is a commercial device which is robust and fast. These new features reduce the size and increase the versatility of the susceptometer, for it can be used with a simple laptop. To test our instrument, we performed measurements on magnetic materials and show that the system is reliable at both room temperature and cryogenic temperatures (77 K). The instrument is suitable for any physics or engineering laboratory either for research or academic purposes.

FDTD assessment of human exposure to electromagnetic fields from WiFi and bluetooth devices in some operating situations.

PubMed

Martínez-Búrdalo, M; Martín, A; Sanchis, A; Villar, R

2009-02-01

In this work, the numerical dosimetry in human exposure to the electromagnetic fields from antennas of wireless devices, such as those of wireless local area networks (WLAN) access points or phone and computer peripherals with Bluetooth antennas, is analyzed with the objective of assessing guidelines compliance. Several geometrical configurations are considered to simulate possible exposure situations of a person to the fields from WLAN or Bluetooth antennas operating at 2400 MHz. The exposure to radiation from two sources of different frequencies when using a 1800 MHz GSM mobile phone connected via Bluetooth with a hands-free car kit is also considered. The finite-difference time-domain (FDTD) method is used to calculate electric and magnetic field values in the vicinity of the antennas and specific absorption rates (SAR) in a high-resolution model of the human head and torso, to be compared with the limits from the guidelines (reference levels and basic restrictions, respectively). Results show that the exposure levels in worst-case situations studied are lower than those obtained when analyzing the exposure to mobile phones, as could be expected because of the low power of the signals and the distance between the human and the antennas, with both field and SAR values being far below the limits established by the guidelines, even when considering the combined exposure to both a GSM and a Bluetooth antenna. Copyright 2008 Wiley-Liss, Inc.

From Sensor Networks to Internet of Things. Bluetooth Low Energy, a Standard for This Evolution.

PubMed

Hortelano, Diego; Olivares, Teresa; Ruiz, M Carmen; Garrido-Hidalgo, Celia; López, Vicente

2017-02-14

Current sensor networks need to be improved and updated to satisfy new essential requirements of the Internet of Things, where cutting-edge applications will appear. These requirements are: total coverage, zero fails (high performance), scalability and sustainability (hardware and software). We are going to evaluate Bluetooth Low Energy as wireless transmission technology and as the ideal candidate for these improvements, due to its low power consumption, its low cost radio chips and its ability to communicate with users directly, using their smartphones or smartbands. However, this technology is relatively recent, and standard network topologies are not able to fulfil its new requirements. To address these shortcomings, the implementation of other more flexible topologies (as the mesh topology) will be very interesting. After studying it in depth, we have identified certain weaknesses, for example, specific devices are needed to provide network scalability, and the need to choose between high performance or sustainability. In this paper, after presenting the studies carried out on these new technologies, we propose a new packet format and a new BLE mesh topology, with two different configurations: Individual Mesh and Collaborative Mesh . Our results show how this topology improves the scalability, sustainability, coverage and performance.

Performance Evaluation of Bluetooth Low Energy: A Systematic Review.

PubMed

Tosi, Jacopo; Taffoni, Fabrizio; Santacatterina, Marco; Sannino, Roberto; Formica, Domenico

2017-12-13

Small, compact and embedded sensors are a pervasive technology in everyday life for a wide number of applications (e.g., wearable devices, domotics, e-health systems, etc.). In this context, wireless transmission plays a key role, and among available solutions, Bluetooth Low Energy (BLE) is gaining more and more popularity. BLE merges together good performance, low-energy consumption and widespread diffusion. The aim of this work is to review the main methodologies adopted to investigate BLE performance. The first part of this review is an in-depth description of the protocol, highlighting the main characteristics and implementation details. The second part reviews the state of the art on BLE characteristics and performance. In particular, we analyze throughput, maximum number of connectable sensors, power consumption, latency and maximum reachable range, with the aim to identify what are the current limits of BLE technology. The main results can be resumed as follows: throughput may theoretically reach the limit of ~230 kbps, but actual applications analyzed in this review show throughputs limited to ~100 kbps; the maximum reachable range is strictly dependent on the radio power, and it goes up to a few tens of meters; the maximum number of nodes in the network depends on connection parameters, on the network architecture and specific device characteristics, but it is usually lower than 10; power consumption and latency are largely modeled and analyzed and are strictly dependent on a huge number of parameters. Most of these characteristics are based on analytical models, but there is a need for rigorous experimental evaluations to understand the actual limits.

Modular, bluetooth enabled, wireless electroencephalograph (EEG) platform.

PubMed

Lovelace, Joseph A; Witt, Tyler S; Beyette, Fred R

2013-01-01

A design for a modular, compact, and accurate wireless electroencephalograph (EEG) system is proposed. EEG is the only non-invasive measure for neuronal function of the brain. Using a number of digital signal processing (DSP) techniques, this neuronal function can be acquired and processed into meaningful representations of brain activity. The system described here utilizes Bluetooth to wirelessly transmit the digitized brain signal for an end application use. In this way, the system is portable, and modular in terms of the device to which it can interface. Brain Computer Interface (BCI) has become a popular extension of EEG systems in modern research. This design serves as a platform for applications using BCI capability.

State of the Art, Trends and Future of Bluetooth Low Energy, Near Field Communication and Visible Light Communication in the Development of Smart Cities

PubMed Central

Cerruela García, Gonzalo; Luque Ruiz, Irene; Gómez-Nieto, Miguel Ángel

2016-01-01

The current social impact of new technologies has produced major changes in all areas of society, creating the concept of a smart city supported by an electronic infrastructure, telecommunications and information technology. This paper presents a review of Bluetooth Low Energy (BLE), Near Field Communication (NFC) and Visible Light Communication (VLC) and their use and influence within different areas of the development of the smart city. The document also presents a review of Big Data Solutions for the management of information and the extraction of knowledge in an environment where things are connected by an “Internet of Things” (IoT) network. Lastly, we present how these technologies can be combined together to benefit the development of the smart city. PMID:27886087

INSIGHT: RFID and Bluetooth enabled automated space for the blind and visually impaired.

PubMed

Ganz, Aura; Gandhi, Siddhesh Rajan; Wilson, Carole; Mullett, Gary

2010-01-01

In this paper we introduce INSIGHT, an indoor location tracking and navigation system to help the blind and visually impaired to easily navigate to their chosen destination in a public building. INSIGHT makes use of RFID and Bluetooth technology deployed within the building to locate and track the users. The PDA based user device interacts with INSIGHT server and provides the user navigation instructions in an audio form. The proposed system provides multi-resolution localization of the users, facilitating the provision of accurate navigation instructions when the user is in the vicinity of the RFID tags as well as accommodating a PANIC button which provides navigation instructions when the user is anywhere in the building. Moreover, the system will continuously monitor the zone in which the user walks. This will enable the system to identify if the user is located in the wrong zone of the building which may not lead to the desired destination.

Research on Knowledge-Based Optimization Method of Indoor Location Based on Low Energy Bluetooth

NASA Astrophysics Data System (ADS)

Li, C.; Li, G.; Deng, Y.; Wang, T.; Kang, Z.

2017-09-01

With the rapid development of LBS (Location-based Service), the demand for commercialization of indoor location has been increasing, but its technology is not perfect. Currently, the accuracy of indoor location, the complexity of the algorithm, and the cost of positioning are hard to be simultaneously considered and it is still restricting the determination and application of mainstream positioning technology. Therefore, this paper proposes a method of knowledge-based optimization of indoor location based on low energy Bluetooth. The main steps include: 1) The establishment and application of a priori and posterior knowledge base. 2) Primary selection of signal source. 3) Elimination of positioning gross error. 4) Accumulation of positioning knowledge. The experimental results show that the proposed algorithm can eliminate the signal source of outliers and improve the accuracy of single point positioning in the simulation data. The proposed scheme is a dynamic knowledge accumulation rather than a single positioning process. The scheme adopts cheap equipment and provides a new idea for the theory and method of indoor positioning. Moreover, the performance of the high accuracy positioning results in the simulation data shows that the scheme has a certain application value in the commercial promotion.

Performance Evaluation of Bluetooth Low Energy: A Systematic Review

PubMed Central

Taffoni, Fabrizio; Santacatterina, Marco; Sannino, Roberto

2017-01-01

Small, compact and embedded sensors are a pervasive technology in everyday life for a wide number of applications (e.g., wearable devices, domotics, e-health systems, etc.). In this context, wireless transmission plays a key role, and among available solutions, Bluetooth Low Energy (BLE) is gaining more and more popularity. BLE merges together good performance, low-energy consumption and widespread diffusion. The aim of this work is to review the main methodologies adopted to investigate BLE performance. The first part of this review is an in-depth description of the protocol, highlighting the main characteristics and implementation details. The second part reviews the state of the art on BLE characteristics and performance. In particular, we analyze throughput, maximum number of connectable sensors, power consumption, latency and maximum reachable range, with the aim to identify what are the current limits of BLE technology. The main results can be resumed as follows: throughput may theoretically reach the limit of ~230 kbps, but actual applications analyzed in this review show throughputs limited to ~100 kbps; the maximum reachable range is strictly dependent on the radio power, and it goes up to a few tens of meters; the maximum number of nodes in the network depends on connection parameters, on the network architecture and specific device characteristics, but it is usually lower than 10; power consumption and latency are largely modeled and analyzed and are strictly dependent on a huge number of parameters. Most of these characteristics are based on analytical models, but there is a need for rigorous experimental evaluations to understand the actual limits. PMID:29236085

Design and implementation of a wireless (Bluetooth) four channel bio-instrumentation amplifier and digital data acquisition device with user-selectable gain, frequency, and driven reference.

PubMed

Cosmanescu, Alin; Miller, Benjamin; Magno, Terence; Ahmed, Assad; Kremenic, Ian

2006-01-01

A portable, multi-purpose Bio-instrumentation Amplifier and Data AcQuisition device (BADAQ) capable of measuring and transmitting EMG and EKG signals wirelessly via Bluetooth is designed and implemented. Common topologies for instrumentation amplifiers and filters are used and realized with commercially available, low-voltage, high precision operational amplifiers. An 8-bit PIC microcontroller performs 10-bit analog-to-digital conversion of the amplified and filtered signals and controls a Bluetooth transceiver capable of wirelessly transmitting the data to any Bluetooth enabled device. Electrical isolation between patient/subject, circuitry, and ancillary equipment is achieved by optocoupling components. The design focuses on simplicity, portability, and affordability.

From Sensor Networks to Internet of Things. Bluetooth Low Energy, a Standard for This Evolution

PubMed Central

Hortelano, Diego; Olivares, Teresa; Ruiz, M. Carmen; Garrido-Hidalgo, Celia; López, Vicente

2017-01-01

Current sensor networks need to be improved and updated to satisfy new essential requirements of the Internet of Things, where cutting-edge applications will appear. These requirements are: total coverage, zero fails (high performance), scalability and sustainability (hardware and software). We are going to evaluate Bluetooth Low Energy as wireless transmission technology and as the ideal candidate for these improvements, due to its low power consumption, its low cost radio chips and its ability to communicate with users directly, using their smartphones or smartbands. However, this technology is relatively recent, and standard network topologies are not able to fulfil its new requirements. To address these shortcomings, the implementation of other more flexible topologies (as the mesh topology) will be very interesting. After studying it in depth, we have identified certain weaknesses, for example, specific devices are needed to provide network scalability, and the need to choose between high performance or sustainability. In this paper, after presenting the studies carried out on these new technologies, we propose a new packet format and a new BLE mesh topology, with two different configurations: Individual Mesh and Collaborative Mesh. Our results show how this topology improves the scalability, sustainability, coverage and performance. PMID:28216560

Bluetooth Low Energy Peripheral Android Health App for Educational and Interoperability Testing Purposes.

PubMed

Frohner, Matthias; Urbauer, Philipp; Sauermann, Stefan

2017-01-01

Based on recent telemonitoring activities in Austria for enabling integrated health care, the communication interfaces between personal health devices (e.g. blood pressure monitor) and personal health gateway devices (e.g. smartphone, routing received information to wide area networks) play an important role. In order to ease testing of the Bluetooth Low Energy interface functionality of the personal health gateway devices, a personal health device simulator was developed. Based on specifications from the Bluetooth SIG a XML software test configuration file structure is defined that declares the specific features of the personal health devices simulated. Using this configuration file, different scenarios are defined, e.g. send a single measurement result from a blood pressure reading or sending multiple (historic) weight scale readings. The simulator is intended to be used for educational purposes in lectures, where the number of physical personal health devices can be reduced and learning can be improved. It could be shown that this simulator assists the development process of mHealth applications by reducing the time needed for development and testing.

Bluetooth telemetry system for a wearable electrocardiogram

NASA Astrophysics Data System (ADS)

Green, Ryan B.

The rise of wireless networks has led to a new market in medicine: remote patient monitoring. Practitioners now desire to monitor the health conditions of their patients after hospital release. With the large number of cardiac related deaths and this new demand in medicine being the motivation, this study developed a BluetoothRTM telemetry system for a wearable Electrocardiogram. This study also developed a compression t-shirt to hold the ECG and telemetry system. This device communicates the ECG signal of a patient to an Android device within the ISM frequency bands (2.4-2.48 GHz) where the data is displayed and stored in real time. This study is a stepping stone toward more portable heart monitoring that can communicate with the doctor in real time from remote locations.

Design of a wearable device for ECG continuous monitoring using wireless technology.

PubMed

Led, Santiago; Fernández, Jorge; Serrano, Luis

2004-01-01

This project focuses on the design and implementation of an intelligent wearable device for ECG continuous acquisition and transmission to some remote gateway using Bluetooth technology. The acquisition device has been designed for having very low power consumption and reduced size. The Analog Devices' ADuC831 Micro-Converter for achieving the analog to digital conversion and the CSR's BlueCore2 chip for the Bluetooth transmission are the core of the device. The designed device is an important component of a complete prototype for remote ECG continuous monitoring of patients with diverse cardiac diseases.

A Digital Compressed Sensing-Based Energy-Efficient Single-Spot Bluetooth ECG Node

PubMed Central

Cai, Zhipeng; Zou, Fumin; Zhang, Xiangyu

2018-01-01

Energy efficiency is still the obstacle for long-term real-time wireless ECG monitoring. In this paper, a digital compressed sensing- (CS-) based single-spot Bluetooth ECG node is proposed to deal with the challenge in wireless ECG application. A periodic sleep/wake-up scheme and a CS-based compression algorithm are implemented in a node, which consists of ultra-low-power analog front-end, microcontroller, Bluetooth 4.0 communication module, and so forth. The efficiency improvement and the node's specifics are evidenced by the experiments using the ECG signals sampled by the proposed node under daily activities of lay, sit, stand, walk, and run. Under using sparse binary matrix (SBM), block sparse Bayesian learning (BSBL) method, and discrete cosine transform (DCT) basis, all ECG signals were essentially undistorted recovered with root-mean-square differences (PRDs) which are less than 6%. The proposed sleep/wake-up scheme and data compression can reduce the airtime over energy-hungry wireless links, the energy consumption of proposed node is 6.53 mJ, and the energy consumption of radio decreases 77.37%. Moreover, the energy consumption increase caused by CS code execution is negligible, which is 1.3% of the total energy consumption. PMID:29599945

A Digital Compressed Sensing-Based Energy-Efficient Single-Spot Bluetooth ECG Node.

PubMed

Luo, Kan; Cai, Zhipeng; Du, Keqin; Zou, Fumin; Zhang, Xiangyu; Li, Jianqing

2018-01-01

Energy efficiency is still the obstacle for long-term real-time wireless ECG monitoring. In this paper, a digital compressed sensing- (CS-) based single-spot Bluetooth ECG node is proposed to deal with the challenge in wireless ECG application. A periodic sleep/wake-up scheme and a CS-based compression algorithm are implemented in a node, which consists of ultra-low-power analog front-end, microcontroller, Bluetooth 4.0 communication module, and so forth. The efficiency improvement and the node's specifics are evidenced by the experiments using the ECG signals sampled by the proposed node under daily activities of lay, sit, stand, walk, and run. Under using sparse binary matrix (SBM), block sparse Bayesian learning (BSBL) method, and discrete cosine transform (DCT) basis, all ECG signals were essentially undistorted recovered with root-mean-square differences (PRDs) which are less than 6%. The proposed sleep/wake-up scheme and data compression can reduce the airtime over energy-hungry wireless links, the energy consumption of proposed node is 6.53 mJ, and the energy consumption of radio decreases 77.37%. Moreover, the energy consumption increase caused by CS code execution is negligible, which is 1.3% of the total energy consumption.

1.8V Operation Power Amplifier IC for Bluetooth Class 1 Utilizing p+-GaAs Gate Hetero-Junction FET

NASA Astrophysics Data System (ADS)

Harima, Fumio; Bito, Yasunori; Takahashi, Hidemasa; Iwata, Naotaka

We have developed a power amplifier IC for Bluetooth Class 1 operating at single low voltage of 1.8V for both control and drain voltages. We can realize it due to fully enhancement-mode hetero-junction FETs utilizing a re-grown p+-GaAs gate technology. The power amplifier is a highly compact design as a small package of 1.5mm×1.5mm×0.4mm with fully integrated gain control and shutdown functions. An impressive power added efficiency of 52% at an output power of 20dBm is achieved with an associated gain of 22dB. Also, sufficiently low leakage current of 0.25μA at 27°C is exhibited, which is comparable to conventional HBT power amplifiers.

A Two-Layer Method for Sedentary Behaviors Classification Using Smartphone and Bluetooth Beacons.

PubMed

Cerón, Jesús D; López, Diego M; Hofmann, Christian

2017-01-01

Among the factors that outline the health of populations, person's lifestyle is the more important one. This work focuses on the caracterization and prevention of sedentary lifestyles. A sedentary behavior is defined as "any waking behavior characterized by an energy expenditure of 1.5 METs (Metabolic Equivalent) or less while in a sitting or reclining posture". To propose a method for sedentary behaviors classification using a smartphone and Bluetooth beacons considering different types of classification models: personal, hybrid or impersonal. Following the CRISP-DM methodology, a method based on a two-layer approach for the classification of sedentary behaviors is proposed. Using data collected from a smartphones' accelerometer, gyroscope and barometer; the first layer classifies between performing a sedentary behavior and not. The second layer of the method classifies the specific sedentary activity performed using only the smartphone's accelerometer and barometer data, but adding indoor location data, using Bluetooth Low Energy (BLE) beacons. To improve the precision of the classification, both layers implemented the Random Forest algorithm and the personal model. This study presents the first available method for the automatic classification of specific sedentary behaviors. The layered classification approach has the potential to improve processing, memory and energy consumption of mobile devices and wearables used.

NASA Bluetooth Wireless Communications

NASA Technical Reports Server (NTRS)

Miller, Robert D.

2007-01-01

NASA has been interested in wireless communications for many years, especially when the crew size of the International Space Station (ISS) was reduced to two members. NASA began a study to find ways to improve crew efficiency to make sure the ISS could be maintained with limited crew capacity and still be a valuable research testbed in Low-Earth Orbit (LEO). Currently the ISS audio system requires astronauts to be tethered to the audio system, specifically a device called the Audio Terminal Unit (ATU). Wireless communications would remove the tether and allow astronauts to freely float from experiment to experiment without having to worry about moving and reconnecting the associated cabling or finding the space equivalent of an extension cord. A wireless communication system would also improve safety and reduce system susceptibility to Electromagnetic Interference (EMI). Safety would be improved because a crewmember could quickly escape a fire while maintaining communications with the ground and other crewmembers at any location. In addition, it would allow the crew to overcome the volume limitations of the ISS ATU. This is especially important to the Portable Breathing Apparatus (PBA). The next generation of space vehicles and habitats also demand wireless attention. Orion will carry up to six crewmembers in a relatively small cabin. Yet, wireless could become a driving factor to reduce launch weight and increase habitable volume. Six crewmembers, each tethered to a panel, could result in a wiring mess even in nominal operations. In addition to Orion, research is being conducted to determine if Bluetooth is appropriate for Lunar Habitat applications.

Design of external sensors board based on Bluetooth interface of smart phones for structural health monitoring system

NASA Astrophysics Data System (ADS)

Yu, Yan; Zhou, Yaping; Zhao, Xuefeng; Li, Dongsheng; Ou, Jinping

2016-04-01

As an important part of new information technology, the Internet of Things(IoT) is based on intelligent perception, recognition technology, ubiquitous computing, ubiquitous network integration, and it is known as the third wave of the development of information industry in the world after the computer and the Internet. And Smart Phones are the general term for a class of mobile phones with a separate operating system and operational memory, in which the third-party service programs including software, games, navigation, et.al, can be installed. Smart Phones, with not only sensors but also actuators, are widely used in the IoT world. As the current hot issues in the engineering area, Structural health monitoring (SHM) is also facing new problems about design ideas in the IoT environment. The development of IoT, wireless sensor network and mobile communication technology, provides a good technical platform for SHM. Based on these facts, this paper introduces a kind of new idea for Structural Health Monitoring using Smart Phones Technique. The system is described in detail, and the external sensor board based on Bluetooth interface is designed, the test based on Smart Phones is finished to validate the implementation and feasibility. The research is preliminary and more tests need to be carried out before it can be of practical use.

Headset Bluetooth and cell phone based continuous central body temperature measurement system.

PubMed

Sanches, J Miguel; Pereira, Bruno; Paiva, Teresa

2010-01-01

The accurate measure of the central temperature is a very important physiologic indicator in several clinical applications, namely, in the characterization and diagnosis of sleep disorders. In this paper a simple system is described to continuously measure the body temperature at the ear. An electronic temperature sensor is coupled to the microphone of a common commercial auricular Bluetooth device that sends the temperature measurements to a mobile phone to which is paired. The measurements are stored at the mobile phone and periodically sent to a medical facility by email or SMS (short messaging service).

Proposal and Evaluation of BLE Discovery Process Based on New Features of Bluetooth 5.0.

PubMed

Hernández-Solana, Ángela; Perez-Diaz-de-Cerio, David; Valdovinos, Antonio; Valenzuela, Jose Luis

2017-08-30

The device discovery process is one of the most crucial aspects in real deployments of sensor networks. Recently, several works have analyzed the topic of Bluetooth Low Energy (BLE) device discovery through analytical or simulation models limited to version 4.x. Non-connectable and non-scannable undirected advertising has been shown to be a reliable alternative for discovering a high number of devices in a relatively short time period. However, new features of Bluetooth 5.0 allow us to define a variant on the device discovery process, based on BLE scannable undirected advertising events, which results in higher discovering capacities and also lower power consumption. In order to characterize this new device discovery process, we experimentally model the real device behavior of BLE scannable undirected advertising events. Non-detection packet probability, discovery probability, and discovery latency for a varying number of devices and parameters are compared by simulations and experimental measurements. We demonstrate that our proposal outperforms previous works, diminishing the discovery time and increasing the potential user device density. A mathematical model is also developed in order to easily obtain a measure of the potential capacity in high density scenarios.

Proposal and Evaluation of BLE Discovery Process Based on New Features of Bluetooth 5.0

PubMed Central

2017-01-01

The device discovery process is one of the most crucial aspects in real deployments of sensor networks. Recently, several works have analyzed the topic of Bluetooth Low Energy (BLE) device discovery through analytical or simulation models limited to version 4.x. Non-connectable and non-scannable undirected advertising has been shown to be a reliable alternative for discovering a high number of devices in a relatively short time period. However, new features of Bluetooth 5.0 allow us to define a variant on the device discovery process, based on BLE scannable undirected advertising events, which results in higher discovering capacities and also lower power consumption. In order to characterize this new device discovery process, we experimentally model the real device behavior of BLE scannable undirected advertising events. Non-detection packet probability, discovery probability, and discovery latency for a varying number of devices and parameters are compared by simulations and experimental measurements. We demonstrate that our proposal outperforms previous works, diminishing the discovery time and increasing the potential user device density. A mathematical model is also developed in order to easily obtain a measure of the potential capacity in high density scenarios. PMID:28867786

A 0.13µm CMOS Bluetooth EDR Transceiver with High Sensitivity over Wide Temperature Range and Immunity to Process Variation

NASA Astrophysics Data System (ADS)

Agawa, Kenichi; Ishizuka, Shinichiro; Majima, Hideaki; Kobayashi, Hiroyuki; Koizumi, Masayuki; Nagano, Takeshi; Arai, Makoto; Shimizu, Yutaka; Maki, Asuka; Urakawa, Go; Terada, Tadashi; Itoh, Nobuyuki; Hamada, Mototsugu; Fujii, Fumie; Kato, Tadamasa; Yoshitomi, Sadayuki; Otsuka, Nobuaki

A 2.4GHz 0.13µm CMOS transceiver LSI, supporting Bluetooth V2.1 + enhanced data rate (EDR) standard, has achieved a high reception sensitivity and high-quality transmission signals between -40°C and +90°C. A low-IF receiver and direct-conversion transmitter architecture are employed. A temperature compensated receiver chain including a low-noise amplifier accomplishes a sensitivity of -90dBm at frequency shift keying modulation even in the worst environmental condition. Design optimization of phase noise in a local oscillator and linearity of a power amplifier improves transmission signals and enables them to meet Bluetooth radio specifications. Fabrication in scaled 0.13µm CMOS and operation at a low supply voltage of 1.5V result in small area and low power consumption.

Body surface mounted biomedical monitoring system using Bluetooth.

PubMed

Nambu, Masayuki

2007-01-01

Continuous monitoring in daily life is important for the health condition control of the elderly. However, portable or wearable devices need to carry by user on their own will. On the other hand, implantation sensors are not adoptable, because of generic users dislike to insert the any object in the body for monitoring. Therefore, another monitoring system of the health condition to carry it easily is necessary. In addition, ID system is necessary even if the subject live with few families. Furthermore, every measurement system should be wireless system, because not to obstruct the daily life of the user. In this paper, we propose the monitoring system, which is mounted on the body surface. This system will not obstruct the action or behavior of user in daily life, because this system attached the body surface on the back of the user. In addition, this system has wireless communication system, using Bluetooth, and acquired data transfer to the outside of the house via the Internet.

An IMU-Aided Body-Shadowing Error Compensation Method for Indoor Bluetooth Positioning

PubMed Central

Deng, Zhongliang

2018-01-01

Research on indoor positioning technologies has recently become a hotspot because of the huge social and economic potential of indoor location-based services (ILBS). Wireless positioning signals have a considerable attenuation in received signal strength (RSS) when transmitting through human bodies, which would cause significant ranging and positioning errors in RSS-based systems. This paper mainly focuses on the body-shadowing impairment of RSS-based ranging and positioning, and derives a mathematical expression of the relation between the body-shadowing effect and the positioning error. In addition, an inertial measurement unit-aided (IMU-aided) body-shadowing detection strategy is designed, and an error compensation model is established to mitigate the effect of body-shadowing. A Bluetooth positioning algorithm with body-shadowing error compensation (BP-BEC) is then proposed to improve both the positioning accuracy and the robustness in indoor body-shadowing environments. Experiments are conducted in two indoor test beds, and the performance of both the BP-BEC algorithm and the algorithms without body-shadowing error compensation (named no-BEC) is evaluated. The results show that the BP-BEC outperforms the no-BEC by about 60.1% and 73.6% in terms of positioning accuracy and robustness, respectively. Moreover, the execution time of the BP-BEC algorithm is also evaluated, and results show that the convergence speed of the proposed algorithm has an insignificant effect on real-time localization. PMID:29361718

An IMU-Aided Body-Shadowing Error Compensation Method for Indoor Bluetooth Positioning.

PubMed

Deng, Zhongliang; Fu, Xiao; Wang, Hanhua

2018-01-20

Research on indoor positioning technologies has recently become a hotspot because of the huge social and economic potential of indoor location-based services (ILBS). Wireless positioning signals have a considerable attenuation in received signal strength (RSS) when transmitting through human bodies, which would cause significant ranging and positioning errors in RSS-based systems. This paper mainly focuses on the body-shadowing impairment of RSS-based ranging and positioning, and derives a mathematical expression of the relation between the body-shadowing effect and the positioning error. In addition, an inertial measurement unit-aided (IMU-aided) body-shadowing detection strategy is designed, and an error compensation model is established to mitigate the effect of body-shadowing. A Bluetooth positioning algorithm with body-shadowing error compensation (BP-BEC) is then proposed to improve both the positioning accuracy and the robustness in indoor body-shadowing environments. Experiments are conducted in two indoor test beds, and the performance of both the BP-BEC algorithm and the algorithms without body-shadowing error compensation (named no-BEC) is evaluated. The results show that the BP-BEC outperforms the no-BEC by about 60.1% and 73.6% in terms of positioning accuracy and robustness, respectively. Moreover, the execution time of the BP-BEC algorithm is also evaluated, and results show that the convergence speed of the proposed algorithm has an insignificant effect on real-time localization.

Real-time estimation of transit OD patterns and delays using low cost-ubiquitous advanced technologies.

DOT National Transportation Integrated Search

2017-04-01

The main objective of this project is to develop and conduct limited testing of novel sensors using Bluetooth technology : (BT) to estimate OD demands and station wait times for users of public transit stations. The NYU research team tested the : fea...

Implementation of NFC technology for industrial applications: case flexible production

NASA Astrophysics Data System (ADS)

Sallinen, Mikko; Strömmer, Esko; Ylisaukko-oja, Arto

2007-09-01

Near Field communication (NFC) technology enables a flexible short range communication. It has large amount of envisaged applications in consumer, welfare and industrial sector. Compared with other short range communication technologies such as Bluetooth or Wibree it provides advantages that we will introduce in this paper. In this paper, we present an example of applying NFC technology to industrial application where simple tasks can be automatized and industrial assembly process can be improved radically by replacing manual paperwork and increasing trace of the products during the production.

Feasibility and performance evaluation of generating and recording visual evoked potentials using ambulatory Bluetooth based system.

PubMed

Ellingson, Roger M; Oken, Barry

2010-01-01

Report contains the design overview and key performance measurements demonstrating the feasibility of generating and recording ambulatory visual stimulus evoked potentials using the previously reported custom Complementary and Alternative Medicine physiologic data collection and monitoring system, CAMAS. The methods used to generate visual stimuli on a PDA device and the design of an optical coupling device to convert the display to an electrical waveform which is recorded by the CAMAS base unit are presented. The optical sensor signal, synchronized to the visual stimulus emulates the brain's synchronized EEG signal input to CAMAS normally reviewed for the evoked potential response. Most importantly, the PDA also sends a marker message over the wireless Bluetooth connection to the CAMAS base unit synchronized to the visual stimulus which is the critical averaging reference component to obtain VEP results. Results show the variance in the latency of the wireless marker messaging link is consistent enough to support the generation and recording of visual evoked potentials. The averaged sensor waveforms at multiple CPU speeds are presented and demonstrate suitability of the Bluetooth interface for portable ambulatory visual evoked potential implementation on our CAMAS platform.

Wibree: wireless communication technology

NASA Astrophysics Data System (ADS)

Fernandes e Fizardo, Trima Piedade

2011-12-01

Nowadays everywhere we come across electronic devices and now the world has become entirely mobile with so many new electronic equipments. The number of computing and telecommunications devices is increasing and consequently the focus on how to connect them to each other. The usual solution is to connect the device with cables or using infra red light to make file transfer and synchronizations possible but infrared light requires line of sight. To solve these problems a new technology,Wibree radio technology complements other local connectivity technologies, consuming only a fraction of the power compared to other radio technologies, enabling smaller and less costly implementations and being easy to integrate with Bluetooth solutions, Furthermore it can be also used to enable communication between several units such as small radio LANs.This paper focuses on why this technology has got large attention although there are pro's and con's with respect to other technologies.

A Low Power SOC Architecture for the V2.0+EDR Bluetooth Using a Unified Verification Platform

NASA Astrophysics Data System (ADS)

Kim, Jeonghun; Kim, Suki; Baek, Kwang-Hyun

This paper presents a low-power System on Chip (SOC) architecture for the v2.0+EDR (Enhanced Data Rate) Bluetooth and its applications. Our design includes a link controller, modem, RF transceiver, Sub-Band Codec (SBC), Expanded Instruction Set Computer (ESIC) processor, and peripherals. To decrease power consumption of the proposed SOC, we reduce data transfer using a dual-port memory, including a power management unit, and a clock gated approach. We also address some of issues and benefits of reusable and unified environment on a centralized data structure and SOC verification platform. This includes flexibility in meeting the final requirements using technology-independent tools wherever possible in various processes and for projects. The other aims of this work are to minimize design efforts by avoiding the same work done twice by different people and to reuse the similar environment and platform for different projects. This chip occupies a die size of 30mm2 in 0.18µm CMOS, and the worst-case current of the total chip is 54mA.

Low-Cost Manufacturing, Usability, and Security: An Analysis of Bluetooth Simple Pairing and Wi-Fi Protected Setup

NASA Astrophysics Data System (ADS)

Kuo, Cynthia; Walker, Jesse; Perrig, Adrian

Bluetooth Simple Pairing and Wi-Fi Protected Setup specify mechanisms for exchanging authentication credentials in wireless networks. Both Simple Pairing and Protected Setup support multiple setup mechanisms, which increases security risks and hurts the user experience. To improve the security and usability of these specifications, we suggest defining a common baseline for hardware features and a consistent, interoperable user experience across devices.

[Wireless human body communication technology].

PubMed

Sun, Lei; Zhang, Xiaojuan

2014-12-01

The Wireless Body Area Network (WBAN) is a key part of the wearable monitoring technologies, which has many communication technologies to choose from, like Bluetooth, ZigBee, Ultra Wideband, and Wireless Human Body Communication (WHBC). As for the WHBC developed in recent years, it is worthy to be further studied. The WHBC has a strong momentum of growth and a natural advantage in the formation of WBAN. In this paper, we first briefly describe the technical background of WHBC, then introduce theoretical model of human-channel communication and digital transmission machine based on human channel. And finally we analyze various of the interference of the WHBC and show the AFH (Adaptive Frequency Hopping) technology which can effectively deal with the interference.

A portable ECG monitoring device with Bluetooth and Holter capabilities for telemedicine applications.

PubMed

Lucani, Daniel; Cataldo, Giancarlos; Cruz, Julio; Villegas, Guillermo; Wong, Sara

2006-01-01

A prototype of a portable ECG-monitoring device has been developed for clinical and non-clinical environments as part of a telemedicine system to provide remote and continuous surveillance of patients. The device can acquire, store and/or transmit ECG signals to computer-based platforms or specially configured access points (AP) with Intranet/Internet capabilities in order to reach remote monitoring stations. Acquired data can be stored in a flash memory card in FAT16 format for later recovery, or transmitted via Bluetooth or USB to a local station or AP. This data acquisition module (DAM) operates in two modes: Holter and on-line transmission.

Model-based testing with UML applied to a roaming algorithm for bluetooth devices.

PubMed

Dai, Zhen Ru; Grabowski, Jens; Neukirchen, Helmut; Pals, Holger

2004-11-01

In late 2001, the Object Management Group issued a Request for Proposal to develop a testing profile for UML 2.0. In June 2003, the work on the UML 2.0 Testing Profile was finally adopted by the OMG. Since March 2004, it has become an official standard of the OMG. The UML 2.0 Testing Profile provides support for UML based model-driven testing. This paper introduces a methodology on how to use the testing profile in order to modify and extend an existing UML design model for test issues. The application of the methodology will be explained by applying it to an existing UML Model for a Bluetooth device.

Ambulatory stress monitoring with a wearable bluetooth electrocardiographic device.

PubMed

Hong, Sungyoup; Yang, Youngmo; Lee, Jangyoung; Yang, Heebum; Park, Kyungnam; Lee, Suyeul; Lee, Inbum; Jang, Yongwon

2010-01-01

We tried to monitor stress by using a wearable one channel ECG device that can send ECG signals through Bluetooth wireless communication. Noxious physical and mental arithmetic stress was given three times repeatedly to healthy adults, and cortisol and catecholamines were measured serially from peripheral blood. At the same time, time domain and frequency domain parameters of heart rate variability (HRV) were calculated by taking precordial electrocardiogram. The intensity of correlation between subjective visual analogue scale (VAS) and catecholamine, cortisol, and HRV parameters according to stress was analyzed by using concordance correlation coefficients. The HRV triangular index and LF/HF ratio had high concordance correlation with the degree of stress in the physical stress model. In mental arithmetic stress model, the HRV triangular index and LF/HF ratio had weak concordance correlation with the degree of stress, and it had lower predictability than epinephrine. In both models, cortisol had some correlation with catecholamine, but it had little correlation with HRV parameters. HRV parameters using wearable one channel ECG device can be useful in predicting acute stress and also in many other areas.

Intelligent Control in Automation Based on Wireless Traffic Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurt Derr; Milos Manic

2007-09-01

Wireless technology is a central component of many factory automation infrastructures in both the commercial and government sectors, providing connectivity among various components in industrial realms (distributed sensors, machines, mobile process controllers). However wireless technologies provide more threats to computer security than wired environments. The advantageous features of Bluetooth technology resulted in Bluetooth units shipments climbing to five million per week at the end of 2005 [1, 2]. This is why the real-time interpretation and understanding of Bluetooth traffic behavior is critical in both maintaining the integrity of computer systems and increasing the efficient use of this technology in controlmore » type applications. Although neuro-fuzzy approaches have been applied to wireless 802.11 behavior analysis in the past, a significantly different Bluetooth protocol framework has not been extensively explored using this technology. This paper presents a new neurofuzzy traffic analysis algorithm of this still new territory of Bluetooth traffic. Further enhancements of this algorithm are presented along with the comparison against the traditional, numerical approach. Through test examples, interesting Bluetooth traffic behavior characteristics were captured, and the comparative elegance of this computationally inexpensive approach was demonstrated. This analysis can be used to provide directions for future development and use of this prevailing technology in various control type applications, as well as making the use of it more secure.« less

Intelligent Control in Automation Based on Wireless Traffic Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurt Derr; Milos Manic

Wireless technology is a central component of many factory automation infrastructures in both the commercial and government sectors, providing connectivity among various components in industrial realms (distributed sensors, machines, mobile process controllers). However wireless technologies provide more threats to computer security than wired environments. The advantageous features of Bluetooth technology resulted in Bluetooth units shipments climbing to five million per week at the end of 2005 [1, 2]. This is why the real-time interpretation and understanding of Bluetooth traffic behavior is critical in both maintaining the integrity of computer systems and increasing the efficient use of this technology in controlmore » type applications. Although neuro-fuzzy approaches have been applied to wireless 802.11 behavior analysis in the past, a significantly different Bluetooth protocol framework has not been extensively explored using this technology. This paper presents a new neurofuzzy traffic analysis algorithm of this still new territory of Bluetooth traffic. Further enhancements of this algorithm are presented along with the comparison against the traditional, numerical approach. Through test examples, interesting Bluetooth traffic behavior characteristics were captured, and the comparative elegance of this computationally inexpensive approach was demonstrated. This analysis can be used to provide directions for future development and use of this prevailing technology in various control type applications, as well as making the use of it more secure.« less

Reducing resistance to polio immunisation with free health camps and Bluetooth messaging: An update from Kaduna, Northern, Nigeria.

PubMed

Birukila, Gerida; Babale, Sufiyan M; Epstein, Helen; Gugong, Victor; Anger, Robert; Corkum, Melissa; Jehoshaphat Nebanat, Albarka; Musoke, Fredrick; Alabi, Olaniran

2017-01-01

Since 1997, the Global Polio Eradication Initiative has sponsored regular door-to-door polio immunisation campaigns in northern Nigeria. On 30 July 2015, the country was finally declared poliofree, a hard won success. At various times, polio eradication has been threatened by rumours and community tensions. For example, in 2003, local Imams, traditional leaders and politicians declared a polio campaign boycott, due to the concerns about the safety of the polio vaccine. Although the campaigns resumed in 2004, many parents continued to refuse vaccination because of the persistence of rumours of vaccine contamination, and anger about the poor state of health services for conditions other than polio. To address this, UNICEF and Nigerian Government partners piloted two interventions: (1) mobile 'health camps' to provide ambulatory care for conditions other than polio and (2) an audiovisual clip about vaccine safety and other health issues, shareable on multimedia mobile phones via Bluetooth pairing. The mobile phone survey found that Bluetooth compatible messages could rapidly spread behavioural health messages in low-literacy communities. The health camps roughly doubled polio vaccine uptake in the urban ward where it was piloted. This suggests that polio eradication would have been accelerated by improving primary health care services.

The Security Aspects of Wireless Local Area Network (WLAN)

DTIC Science & Technology

2003-09-01

by wireless links to enable devices to communicate. In a Bluetooth network, mobile routers control the changing network topologies of these... Bluetooth Bluetooth is a simple peer-to-peer protocol created to connect multiple consumer mobile information devices (cellular phones, laptops...technology [Ref 2]. Bluetooth enables mobile devices to avoid interference from other signals by hopping to a new frequency after transmitting or

Contextual Computing: A Bluetooth based approach for tracking healthcare providers in the emergency room.

PubMed

Frisby, Joshua; Smith, Vernon; Traub, Stephen; Patel, Vimla L

2017-01-01

Hospital Emergency Departments (EDs) frequently experience crowding. One of the factors that contributes to this crowding is the "door to doctor time", which is the time from a patient's registration to when the patient is first seen by a physician. This is also one of the Meaningful Use (MU) performance measures that emergency departments report to the Center for Medicare and Medicaid Services (CMS). Current documentation methods for this measure are inaccurate due to the imprecision in manual data collection. We describe a method for automatically (in real time) and more accurately documenting the door to physician time. Using sensor-based technology, the distance between the physician and the computer is calculated by using the single board computers installed in patient rooms that log each time a Bluetooth signal is seen from a device that the physicians carry. This distance is compared automatically with the accepted room radius to determine if the physicians are present in the room at the time logged to provide greater precision. The logged times, accurate to the second, were compared with physicians' handwritten times, showing automatic recordings to be more precise. This real time automatic method will free the physician from extra cognitive load of manually recording data. This method for evaluation of performance is generic and can be used in any other setting outside the ED, and for purposes other than measuring physician time. Copyright © 2016 Elsevier Inc. All rights reserved.

Introduction to Blueweb: A Decentralized Scatternet Formation Algorithm for Bluetooth Ad Hoc Networks

NASA Astrophysics Data System (ADS)

Yu, Chih-Min; Huang, Chia-Chi

In this letter, a decentralized scatternet formation algorithm called Bluelayer is proposed. First, Bluelayer uses a designated root to construct a tree-shaped subnet and propagates an integer variable k1 called counter limit as well as a constant k in its downstream direction to determine new roots. Then each new root asks its upstream master to start a return connection procedure to convert the tree-shaped subnet into a web-shaped subnet for its immediate upstream root. At the same time, each new root repeats the same procedure as the root to build its own subnet until the whole scatternet is formed. Simulation results show that Bluelayer achieves good network scalability and generates an efficient scatternet configuration for various sizes of Bluetooth ad hoc network.

Adaptive Kalman filter for indoor localization using Bluetooth Low Energy and inertial measurement unit.

PubMed

Yoon, Paul K; Zihajehzadeh, Shaghayegh; Bong-Soo Kang; Park, Edward J

2015-08-01

This paper proposes a novel indoor localization method using the Bluetooth Low Energy (BLE) and an inertial measurement unit (IMU). The multipath and non-line-of-sight errors from low-power wireless localization systems commonly result in outliers, affecting the positioning accuracy. We address this problem by adaptively weighting the estimates from the IMU and BLE in our proposed cascaded Kalman filter (KF). The positioning accuracy is further improved with the Rauch-Tung-Striebel smoother. The performance of the proposed algorithm is compared against that of the standard KF experimentally. The results show that the proposed algorithm can maintain high accuracy for position tracking the sensor in the presence of the outliers.

Measurements of complex impedance in microwave high power systems with a new bluetooth integrated circuit.

PubMed

Roussy, Georges; Dichtel, Bernard; Chaabane, Haykel

2003-01-01

By using a new integrated circuit, which is marketed for bluetooth applications, it is possible to simplify the method of measuring the complex impedance, complex reflection coefficient and complex transmission coefficient in an industrial microwave setup. The Analog Devices circuit AD 8302, which measures gain and phase up to 2.7 GHz, operates with variable level input signals and is less sensitive to both amplitude and frequency fluctuations of the industrial magnetrons than are mixers and AM crystal detectors. Therefore, accurate gain and phase measurements can be performed with low stability generators. A mechanical setup with an AD 8302 is described; the calibration procedure and its performance are presented.

Use of telehealth technology for home spirometry after lung transplantation: a randomized controlled trial.

PubMed

Sengpiel, Juliane; Fuehner, Thomas; Kugler, Christiane; Avsar, Murat; Bodmann, Isabelle; Boemke, Annelies; Simon, Andre; Welte, Tobias; Gottlieb, Jens

2010-12-01

Complications often occur during the early phase after lung transplantation, and rapid diagnosis is vital. Home spirometry is used to detect early changes in graft function. Bluetooth-equipped cell phones are easy to use and facilitate data transfer from home spirometry. To explore use of home spirometry with Bluetooth data transfer in outpatient lung transplant recipients. Single-center prospective randomized controlled trial. Intervention-Fifty-six patients were randomized either to home spirometry with data transfer via Bluetooth-equipped cell phones or to home spirometry alone before discharge after lung transplantation. In the Bluetooth group, results were transferred to a database capable of generating alarm messages. Time from onset of symptoms to physician consultation during the first 6 months after lung transplantation was the primary end point. Adherence to home spirometry was 97.2% in the Bluetooth group and 95.3% in the home spirometry alone group (P = .73). Median time to first consultation (P = .60) and frequency of consultation (P = .06) did not differ significantly in the 2 groups. Mean scores on the Hospital Anxiety and Depression Scale were lower in patients in the Bluetooth group (1.5; range, 0.0-4.0) than in the home spirometry alone group (4.0; range, 2.0-6.0; P = .04). Home spirometry with data transfer is feasible and safe in lung transplant recipients. Compared with home spirometry alone, additional data transfer was equally effective regarding the time interval from symptom onset to consultation. Patients in the Bluetooth group reported less anxiety, which may improve emotional well-being.

Navigation studies based on the ubiquitous positioning technologies

NASA Astrophysics Data System (ADS)

Ye, Lei; Mi, Weijie; Wang, Defeng

2007-11-01

This paper summarized the nowadays positioning technologies, such as absolute positioning methods and relative positioning methods, indoor positioning and outdoor positioning, active positioning and passive positioning. Global Navigation Satellite System (GNSS) technologies were introduced as the omnipresent out-door positioning technologies, including GPS, GLONASS, Galileo and BD-1/2. After analysis of the shortcomings of GNSS, indoor positioning technologies were discussed and compared, including A-GPS, Cellular network, Infrared, Electromagnetism, Computer Vision Cognition, Embedded Pressure Sensor, Ultrasonic, RFID (Radio Frequency IDentification), Bluetooth, WLAN etc.. Then the concept and characteristics of Ubiquitous Positioning was proposed. After the ubiquitous positioning technologies contrast and selection followed by system engineering methodology, a navigation system model based on Incorporate Indoor-Outdoor Positioning Solution was proposed. And this model was simulated in the Galileo Demonstration for World Expo Shanghai project. In the conclusion, the prospects of ubiquitous positioning based navigation were shown, especially to satisfy the public location information acquiring requirement.

Smartphone-based support system (SoberDiary) coupled with a Bluetooth breathalyser for treatment-seeking alcohol-dependent patients.

PubMed

You, Chuang-Wen; Chen, Yen-Chang; Chen, Chun-Hsin; Lee, Chao-Hui; Kuo, Po-Hsiu; Huang, Ming-Chyi; Chu, Hao-Hua

2017-02-01

Relapse prevention in patients with alcohol dependence (AD) has long been a clinical challenge. It is vital to provide services with minial restrictions for patients to have access to continuous after-treatment care. The study was aimed to examine the benefits of a smartphone application (SoberDiary) coupled to a Bluetooth breathalyser to assist patients recovering from alcohol dependence (AD). This study recruited 38 patients that fulfilled the DSM-IV-TR criteria for AD and who were undergoing an outpatient maintenance program for abstinence. The participants were provided a breathalyser and smartphone-equipped SoberDiary and followed for 12weeks. The participants were divided into highly adherent (HA) and less adherent (LA) groups according to the medium number of reward points they were awarded for using the SoberDiary system throughout the follow-up period based on the average amount of time spent on using the application, the number of function modules they accessed, and the number of BrAC tests they completed each day. 19 of the patients were classified as HA and 19 patients were classified as LA group. Members of the HA group recorded fewer drinking days and drinks consumed per week, a higher cumulative number of abstinence days, a higher abstinence rate, less pronounced anxiety, and superior quality of life. The proposed smartphone-assisted support system coupled with a Bluetooth breathalyser might be a feasible supplement to conventional treatment for AD. Higher SoberDiary compliance appears to be associated with better clinical outcomes. Copyright © 2016. Published by Elsevier Ltd.

SEMICONDUCTOR INTEGRATED CIRCUITS 8.64-11.62 GHz CMOS VCO and divider in a zero-IF 802.11a/b/g WLAN and Bluetooth application

NASA Astrophysics Data System (ADS)

Yu, Sun; Niansong, Mei; Bo, Lu; Yumei, Huang; Zhiliang, Hong

2010-10-01

A fully integrated VCO and divider implemented in SMIC 0.13-μm RFCMOS 1P8M technology with a 1.2 V supply voltage is presented. The frequency of the VCO is tuning from 8.64 to 11.62 GHz while the quadrature LO signals for 802.11a WLAN in 5.8 GHz band or for 802.11b/g WLAN and Bluetooth in 2.4 GHz band can be obtained by a frequency division by 2 or 4, respectively. A 6 bit switched capacitor array is applied for precise tuning of all necessary frequency bands. The testing results show that the VCO has a phase noise of—113 dBc @ 1 MHz offset from the carrier of 5.5 GHz by dividing VCO output by two and the VCO core consumes 3.72 mW. The figure-of-merit for the tuning-range (FOMT) of the VCO is -192.6 dBc/Hz.

Personal Information Search on Mobile Devices

DTIC Science & Technology

2007-09-01

Networking .....................28 a. Bluetooth ...............................28 b. Infrared ................................29 2. Mobile Data...Also in this chapter, the connection techniques and schemes including Bluetooth , GPRS, Wi-Fi will be discussed. Chapter IV is devoted to a...characteristics of mobile devices. Recent advances in networking technologies such as 802.11 and Bluetooth enable these new mobile devices to connect to

Bluetooth gas sensing module combined with smartphones for air quality monitoring.

PubMed

Suárez, José Ignacio; Arroyo, Patricia; Lozano, Jesús; Herrero, José Luis; Padilla, Manuel

2018-08-01

This study addresses the development of a miniaturized (60 × 60 mm) Wireless Sensing Module (WSM) for environmental application and air quality detection. The proposed prototype has six sensors: one for humidity, one for ambient temperature (SHT21 from Sensirion), and four for gas detection (MiCS-4514, MiCS-5526 and MiCS-5914 from SGX Sensortech). The core of the system is based on a high performance 8-bit microcontroller, model PIC18F46K80, from Microchip. The obtained data values were transmitted to the Smartphone through a Bluetooth communication module and a home-developed Android app. The discrimination capability of the module is tested with 10 volatile organic compounds (acetone, acetic acid, benzene, ethanol, ethyl acetate, ethylbenzene, formaldehyde, toluene, xylene, and dimethylacetamide) and the effect of humidity and drift of the sensors is also studied. Results show that 88.33% and 92.22% success rates in classification stage are obtained using Multilayer Perceptron with BackPropagation Learning algorithm and Radial-Basis based Neural Networks, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Low-energy Bluetooth for detecting real-world penetrance of bystander naloxone kits: a pilot study.

PubMed

Lai, Jeffrey T; Chapman, Brittany P; Boyle, Katherine L; Boyer, Edward W; Chai, Peter R

2018-01-03

Opioid overdose is a growing public health emergency in the United States. The antidote naloxone must be administered rapidly after opioid overdose to prevent death. Bystander or "take-home" naloxone programs distribute naloxone to opioid users and other community members to increase naloxone availability at the time of overdose. However, data describing the natural history of take-home naloxone in the hands of at-risk individuals is lacking. To understand patterns of naloxone uptake in at-risk users, we developed a smart naloxone kit that uses low-energy Bluetooth (BLE) to unobtrusively detect the transit of naloxone through a hospital campus. In this paper, we describe development of the smart naloxone kit and results from the first 10 participants in our pilot study.

Low Power Multi-Hop Networking Analysis in Intelligent Environments.

PubMed

Etxaniz, Josu; Aranguren, Gerardo

2017-05-19

Intelligent systems are driven by the latest technological advances in many different areas such as sensing, embedded systems, wireless communications or context recognition. This paper focuses on some of those areas. Concretely, the paper deals with wireless communications issues in embedded systems. More precisely, the paper combines the multi-hop networking with Bluetooth technology and a quality of service (QoS) metric, the latency. Bluetooth is a radio license-free worldwide communication standard that makes low power multi-hop wireless networking available. It establishes piconets (point-to-point and point-to-multipoint links) and scatternets (multi-hop networks). As a result, many Bluetooth nodes can be interconnected to set up ambient intelligent networks. Then, this paper presents the results of the investigation on multi-hop latency with park and sniff Bluetooth low power modes conducted over the hardware test bench previously implemented. In addition, the empirical models to estimate the latency of multi-hop communications over Bluetooth Asynchronous Connectionless Links (ACL) in park and sniff mode are given. The designers of devices and networks for intelligent systems will benefit from the estimation of the latency in Bluetooth multi-hop communications that the models provide.

Low Power Multi-Hop Networking Analysis in Intelligent Environments

PubMed Central

Etxaniz, Josu; Aranguren, Gerardo

2017-01-01

Intelligent systems are driven by the latest technological advances in many different areas such as sensing, embedded systems, wireless communications or context recognition. This paper focuses on some of those areas. Concretely, the paper deals with wireless communications issues in embedded systems. More precisely, the paper combines the multi-hop networking with Bluetooth technology and a quality of service (QoS) metric, the latency. Bluetooth is a radio license-free worldwide communication standard that makes low power multi-hop wireless networking available. It establishes piconets (point-to-point and point-to-multipoint links) and scatternets (multi-hop networks). As a result, many Bluetooth nodes can be interconnected to set up ambient intelligent networks. Then, this paper presents the results of the investigation on multi-hop latency with park and sniff Bluetooth low power modes conducted over the hardware test bench previously implemented. In addition, the empirical models to estimate the latency of multi-hop communications over Bluetooth Asynchronous Connectionless Links (ACL) in park and sniff mode are given. The designers of devices and networks for intelligent systems will benefit from the estimation of the latency in Bluetooth multi-hop communications that the models provide. PMID:28534847

Use of Energy Efficient Sensor Networks to Enhance Dynamic Data Gathering Systems: A Comparative Study between Bluetooth and ZigBee.

PubMed

Gheorghiu, Razvan Andrei; Iordache, Valentin

2018-06-03

As road traffic conditions worsen due to the constantly increasing number of cars, traffic management systems are struggling to provide a suitable environment, by gathering all the relevant information from the road network. However, in most cases these are obtained via traffic detectors placed near road junctions, thus providing no information on the conditions in between. A large-scale sensor network using detectors on the majority of vehicles would certainly be capable of providing useful data, but has two major impediments: the equipment installed on the vehicles should be cheap enough (assuming the willingness of private car owners to be a part of the network) and be capable of transferring the required amount of data in due time, as the vehicle passes by the road side unit that acts as interface with the traffic management system. These restrictions reduce the number of technologies that can be used. In this article a series of comprehensive tests have been performed to evaluate the Bluetooth and ZigBee protocols for this purpose from many points of view: handshake time, static and dynamic data transfer (in laboratory conditions and in real traffic conditions). An assessment of the environmental conditions (during tests and probable to be encountered in real conditions) was also provided.

A water-powered Energy Harvesting system with Bluetooth Low Energy interface

NASA Astrophysics Data System (ADS)

Kroener, M.; Allinger, K.; Berger, M.; Grether, E.; Wieland, F.; Heller, S.; Woias, P.

2016-11-01

This paper reports the design, and testing of a water turbine generator system for typical flow rates in domestic applications, with an integrated power management and a Bluetooth low energy (BLE) based RF data transmission interface. It is based on a commercially available low cost hydro generator. The generator is built into a housing with optimized reduced fluidic resistance to enable operation with flow rates as low as 6 l/min. The power management combines rectification, buffering, defined start-up, and circuit protection. An MSP430FR5949 microcontroller is used for data acquisition and processing. The data are transmitted via RF, using a Bluegiga BLE112 module in advertisement mode, to a PC where the measured flow rate is stored and displayed. The transmission rate of the wireless sensor node (WSN) is set to 1 Hz if enough power is available, which is the case for flow rates above 5.5 l/min. The electronics power demand is calculated to be 340 μW in average, while the generator is capable of delivering more than 200 mW for flow rates above 15 l/min.

Comparison of Ecological Momentary Assessment Versus Direct Measurement of E-Cigarette Use With a Bluetooth-Enabled E-Cigarette: A Pilot Study

PubMed Central

Elmasry, Hoda; Das, Babita; Smiley, Sabrina L; Rubin, Leslie F; DeAtley, Teresa; Harvey, Emily; Zhou, Yitong; Niaura, Raymond; Abrams, David B

2017-01-01

Background Assessing the frequency and intensity of e-cigarette use presents special challenges beyond those posed by cigarette use. Accurate measurement of e-cigarette consumption, puff duration, and the stability of these measures over time will be informative for estimating the behavioral and health effects of e-cigarette use. Objective The purpose of this pilot study was to compare the accuracy of self-reported e-cigarette puff counts collected via ecological momentary assessment (EMA) to objective puff count data collected by a Bluetooth-enabled e-cigarette device and to examine the feasibility and acceptability of using a second-generation e-cigarette among adult smokers. Methods A total of 5 adult smokers were enrolled in a longitudinal parent study assessing how e-cigarette use affects cigarette use among e-cigarette–naïve smokers. Using a text message–based EMA system, participants reported e-cigarette puffs for 2 weeks. Participants were also given a Bluetooth-enabled e-cigarette (Smokio) that passively collected puff counts and puff duration. Comparisons between mean reports of Smokio (device-report) and EMA (self-report) use were evaluated using paired t tests. Correlation and agreement between device- and self-reports were evaluated using Pearson correlation and the concordance correlation coefficient (CCC), respectively. A linear mixed effect model was used to determine the fixed effect of timing and Smokio-reported daily puffs on report accuracy. We examined the relationship between time of day and reporting accuracy using Tukey's test for multiple pairwise comparisons. Results A total of 5 African American participants, 4 men and 1 woman, who ranged in age from 24 to 59 years completed the study, resulting in 5180 observations (device-report) of e-cigarette use. At baseline, participants reported smoking for 5 to 25 years and consumed a mean of 7 to 13 cigarettes per day (CPD); 4 smoked within 30 minutes of waking. At the 30-day follow-up, CPD

J2ME and smart phones as platform for a Bluetooth body area network for patient-telemonitoring.

PubMed

Morón, M J; Luque, J R; Botella, A A; Cuberos, E J; Casilari, E; Díaz-Estrella, A

2007-01-01

A prototype of a system based on a Bluetooth Body Area Network (BAN) for continuous and wireless telemonitoring of patients' biosignals is presented. Smart phones and Java (J2ME) have been selected as platform to build a central node in patients' BAN. A midlet running in the smart phone compiles information about patient's location and health status. The midlet encrypts and retransmits it to the server through 802.11 or GPRS/UMTS. Besides when an alerting condition is detected, the midlet generates a MMS and a SMS to be sent to patients' relatives and to physician, respectively. Additionally, the system provides to physicians the possibility of configuring BAN's parameters remotely, from a PC or even a smart phone.

[Current status of the development of wireless sensors for medical applications].

PubMed

Moor, C; Braecklein, M; Jörns, N

2005-01-01

Wireless near-field transmission has been a challenge for scientists developing medical sensors for a long time. Here, instruments which measure a patient's ECG, oxygen saturation, blood pressure, peak flow, weight, blood glucose etc. are to be equipped with suitable transmission technology. Application scenarios for these sensors can be found in all medical areas where cable connections are irritating for the doctor, patient and other care personnel. This problem is especially common in sport medicine, sleep medicine, emergency medicine and intensive care. Based on its beneficial properties with regard to power consumption, range, data security and network capability, the worldwide standard radio technology Bluetooth was selected to transmit measurements. Since digital data is sent to a receiving station via Bluetooth, the measurement pre-processing now takes place in the patient sensor itself, instead of being processed by the monitor. In this article, a Bluetooth ECG, Bluetooth pulse oximeter, Bluetooth peak flow meter and Bluetooth event recorder will be introduced. On the one hand, systems can be realized with these devices, which allow patients to be monitored online (ECG, pulse oximeter). These devices can also be integrated in disease management programs (peak flow meter) and can be used to monitor high-risk patients in their home environment (event recorder).

Dual Band Metamaterial Antenna For LTE/Bluetooth/WiMAX System.

PubMed

Hasan, Md Mehedi; Faruque, Mohammad Rashed Iqbal; Islam, Mohammad Tariqul

2018-01-19

A compact metamaterial inspired antenna operate at LTE, Bluetooth and WiMAX frequency band is introduced in this paper. For the lower band, the design utilizes an outer square metallic strip forcing the patch to radiate as an equivalent magnetic-current loop. For the upper band, another magnetic current loop is created by adding metamaterial structure near the feed line on the patch. The metamaterial inspired antenna dimension of 42 × 32 mm 2 compatible to wireless devices. Finite integration technique based CST Microwave Studio simulator has been used to design and numerical investigation as well as lumped circuit model of the metamaterial antenna is explained with proper mathematical derivation. The achieved measured dual band operation of the conventional antenna are sequentially, 0.561~0.578 GHz, 2.346~2.906 GHz, and 2.91~3.49 GHz, whereas the metamaterial inspired antenna shows dual-band operation from 0.60~0.64 GHz, 2.67~3.40 GHz and 3.61~3.67 GHz, respectively. Therefore, the metamaterial antenna is applicable for LTE and WiMAX applications. Besides, the measured metamaterial antenna gains of 0.15~3.81 dBi and 3.47~3.75 dBi, respectively for the frequency band of 2.67~3.40 GHz and 3.61~3.67 GHz.

Comparison of Ecological Momentary Assessment Versus Direct Measurement of E-Cigarette Use With a Bluetooth-Enabled E-Cigarette: A Pilot Study.

PubMed

Pearson, Jennifer L; Elmasry, Hoda; Das, Babita; Smiley, Sabrina L; Rubin, Leslie F; DeAtley, Teresa; Harvey, Emily; Zhou, Yitong; Niaura, Raymond; Abrams, David B

2017-05-29

Assessing the frequency and intensity of e-cigarette use presents special challenges beyond those posed by cigarette use. Accurate measurement of e-cigarette consumption, puff duration, and the stability of these measures over time will be informative for estimating the behavioral and health effects of e-cigarette use. The purpose of this pilot study was to compare the accuracy of self-reported e-cigarette puff counts collected via ecological momentary assessment (EMA) to objective puff count data collected by a Bluetooth-enabled e-cigarette device and to examine the feasibility and acceptability of using a second-generation e-cigarette among adult smokers. A total of 5 adult smokers were enrolled in a longitudinal parent study assessing how e-cigarette use affects cigarette use among e-cigarette-naïve smokers. Using a text message-based EMA system, participants reported e-cigarette puffs for 2 weeks. Participants were also given a Bluetooth-enabled e-cigarette (Smokio) that passively collected puff counts and puff duration. Comparisons between mean reports of Smokio (device-report) and EMA (self-report) use were evaluated using paired t tests. Correlation and agreement between device- and self-reports were evaluated using Pearson correlation and the concordance correlation coefficient (CCC), respectively. A linear mixed effect model was used to determine the fixed effect of timing and Smokio-reported daily puffs on report accuracy. We examined the relationship between time of day and reporting accuracy using Tukey's test for multiple pairwise comparisons. A total of 5 African American participants, 4 men and 1 woman, who ranged in age from 24 to 59 years completed the study, resulting in 5180 observations (device-report) of e-cigarette use. At baseline, participants reported smoking for 5 to 25 years and consumed a mean of 7 to 13 cigarettes per day (CPD); 4 smoked within 30 minutes of waking. At the 30-day follow-up, CPD range decreased to 1 to 3 cigarettes; 4

Design of an indoor self-positioning system for the visually impaired--simulation with RFID and Bluetooth in a visible light communication system.

PubMed

Liu, Xiaohan; Makino, Hideo; Kobayashi, Suguru; Maeda, Yoshinobu

2007-01-01

After a public experiment of the indoor guidance system using FLC (fluorescent light communication), we found that FLC provides a promising medium for the installation of a guidance system for the visually impaired. However, precise self-positioning was not satisfactorily achieved. In this article, we propose a new self-positioning method, one that uses a combination of RFID (Radio-frequency identification), Bluetooth and FLC. We analyzed the situation and developed a model that combined the three communication modes. Then we performed a series of experiments and get some results in the first step.

Epidemic of cell phone virus

NASA Astrophysics Data System (ADS)

Wang, Pu; González, Marta; Barabási, Albert-László.

2008-03-01

Standard operating systems and Bluetooth technology will be a trend for future cell phone features. These will enable cell phone viruses to spread either through SMS or by sending Bluetooth requests when cell phones are physically close enough. The difference in spreading methods gives these two types of viruses' different epidemiological characteristics. SMS viruses' spread is mainly based on people's social connections, whereas the spreading of Bluetooth viruses is affected by people's mobility patterns and population distribution. Using cell phone data recording calls, SMS and locations of more than 6 million users, we study the spread of SMS and Bluetooth viruses and characterize how the social network and the mobility of mobile phone users affect such spreading processes.

Trial of real-time locating and messaging system with Bluetooth low energy.

PubMed

Arisaka, Naoya; Mamorita, Noritaka; Isonaka, Risa; Kawakami, Tadashi; Takeuchi, Akihiro

2016-09-14

Hospital real-time location systems (RTLS) are increasing efficiency and reducing operational costs, but room access tags are necessary. We developed three iPhone 5 applications for an RTLS and communications using Bluetooth low energy (BLE). The applications were: Peripheral device tags, Central beacons, and a Monitor. A Peripheral communicated with a Central using BLE. The Central communicated with a Monitor using sockets on TCP/IP (Transmission Control Protocol/Internet Protocol) via a WLAN (wireless local area network). To determine a BLE threshold level for the received signal strength indicator (RSSI), relationships between signal strength and distance were measured in our laboratory and on the terrace. The BLE RSSI threshold was set at -70 dB, about 10 m. While an individual with a Peripheral moved around in a concrete building, the Peripheral was captured in a few 10-sec units at about 10 m from a Central. The Central and Monitor showed and saved the approach events, location, and Peripheral's nickname sequentially in real time. Remote Centrals also interactively communicate with Peripherals by intermediating through Monitors that found the nickname in the event database. Trial applications using BLE on iPhones worked well for patient tracking, and messaging in indoor environments.

Fusing Bluetooth Beacon Data with Wi-Fi Radiomaps for Improved Indoor Localization

PubMed Central

Kanaris, Loizos; Kokkinis, Akis; Liotta, Antonio; Stavrou, Stavros

2017-01-01

Indoor user localization and tracking are instrumental to a broad range of services and applications in the Internet of Things (IoT) and particularly in Body Sensor Networks (BSN) and Ambient Assisted Living (AAL) scenarios. Due to the widespread availability of IEEE 802.11, many localization platforms have been proposed, based on the Wi-Fi Received Signal Strength (RSS) indicator, using algorithms such as K-Nearest Neighbour (KNN), Maximum A Posteriori (MAP) and Minimum Mean Square Error (MMSE). In this paper, we introduce a hybrid method that combines the simplicity (and low cost) of Bluetooth Low Energy (BLE) and the popular 802.11 infrastructure, to improve the accuracy of indoor localization platforms. Building on KNN, we propose a new positioning algorithm (dubbed i-KNN) which is able to filter the initial fingerprint dataset (i.e., the radiomap), after considering the proximity of RSS fingerprints with respect to the BLE devices. In this way, i-KNN provides an optimised small subset of possible user locations, based on which it finally estimates the user position. The proposed methodology achieves fast positioning estimation due to the utilization of a fragment of the initial fingerprint dataset, while at the same time improves positioning accuracy by minimizing any calculation errors. PMID:28394268

Fusing Bluetooth Beacon Data with Wi-Fi Radiomaps for Improved Indoor Localization.

PubMed

Kanaris, Loizos; Kokkinis, Akis; Liotta, Antonio; Stavrou, Stavros

2017-04-10

Indoor user localization and tracking are instrumental to a broad range of services and applications in the Internet of Things (IoT) and particularly in Body Sensor Networks (BSN) and Ambient Assisted Living (AAL) scenarios. Due to the widespread availability of IEEE 802.11, many localization platforms have been proposed, based on the Wi-Fi Received Signal Strength (RSS) indicator, using algorithms such as K -Nearest Neighbour (KNN), Maximum A Posteriori (MAP) and Minimum Mean Square Error (MMSE). In this paper, we introduce a hybrid method that combines the simplicity (and low cost) of Bluetooth Low Energy (BLE) and the popular 802.11 infrastructure, to improve the accuracy of indoor localization platforms. Building on KNN, we propose a new positioning algorithm (dubbed i-KNN) which is able to filter the initial fingerprint dataset (i.e., the radiomap), after considering the proximity of RSS fingerprints with respect to the BLE devices. In this way, i-KNN provides an optimised small subset of possible user locations, based on which it finally estimates the user position. The proposed methodology achieves fast positioning estimation due to the utilization of a fragment of the initial fingerprint dataset, while at the same time improves positioning accuracy by minimizing any calculation errors.

Circularly polarized triple band glass shaped monopole patch antenna with metallic reflector for bluetooth & wireless applications

NASA Astrophysics Data System (ADS)

Jangid, K. G.; Choudhary, N.; Jain, P.; Sharma, B. R.; Saini, J. S.; Kulhar, V. S.; Bhatnagar, D.

2016-03-01

This paper presents the design and performance of strip line fed glass shaped monopole patch antenna having with overall size 30mm × 30 mm × 1.59 mm. In the patch; an eight shaped slot and in the ground plane an eight shaped ring are introduced. A metallic ground plane is also introduced at appropriate location beneath the ground plane. The proposed antenna is simulated by applying CST Microwave Studio simulator. Antenna provides circularly polarized radiations, triple broad impedance bandwidth of 203MHz (2.306GHz to 2.510GHz), 42MHz (2.685GHz to 2.757GHz) & GHz (3.63 GHz to 6.05 GHz), high flat gain (close to 5dBi) and good radiation properties in the desired frequency range. This antenna may be a very useful tool for 2.45GHz Bluetooth communication band as well as for 2.4GHz/5.2 GHz /5.8 GHz WLAN bands & 3.7GHz/5.5 GHz Wi-Max bands.

Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy.

PubMed

de Blasio, Gabriel; Quesada-Arencibia, Alexis; García, Carmelo R; Molina-Gil, Jezabel Miriam; Caballero-Gil, Cándido

2017-06-06

This paper presents a study of positioning system that provides advanced information services based on Wi-Fi and Bluetooth Low Energy (BLE) technologies. It uses Wi-Fi for rough positioning and BLE for fine positioning. It is designed for use in public transportation system stations and terminals where the conditions are "hostile" or unfavourable due to signal noise produced by the continuous movement of passengers and buses, data collection conducted in the constant presence thereof, multipath fading, non-line of sight (NLOS) conditions, the fact that part of the wireless communication infrastructure has already been deployed and positioned in a way that may not be optimal for positioning purposes, variable humidity conditions, etc. The ultimate goal is to provide a service that may be used to assist people with special needs. We present experimental results based on scene analysis; the main distance metric used was the Euclidean distance but the Mahalanobis distance was also used in one case. The algorithm employed to compare fingerprints was the weighted k -nearest neighbor one. For Wi-Fi, with only three visible access points, accuracy ranged from 3.94 to 4.82 m, and precision from 5.21 to 7.0 m 90% of the time. With respect to BLE, with a low beacon density (1 beacon per 45.7 m²), accuracy ranged from 1.47 to 2.15 m, and precision from 1.81 to 3.58 m 90% of the time. Taking into account the fact that this system is designed to work in real situations in a scenario with high environmental fluctuations, and comparing the results with others obtained in laboratory scenarios, our results are promising and demonstrate that the system would be able to position users with these reasonable values of accuracy and precision.

Study on an Indoor Positioning System for Harsh Environments Based on Wi-Fi and Bluetooth Low Energy

PubMed Central

de Blasio, Gabriel; Quesada-Arencibia, Alexis; García, Carmelo R.; Molina-Gil, Jezabel Miriam; Caballero-Gil, Cándido

2017-01-01

This paper presents a study of positioning system that provides advanced information services based on Wi-Fi and Bluetooth Low Energy (BLE) technologies. It uses Wi-Fi for rough positioning and BLE for fine positioning. It is designed for use in public transportation system stations and terminals where the conditions are “hostile” or unfavourable due to signal noise produced by the continuous movement of passengers and buses, data collection conducted in the constant presence thereof, multipath fading, non-line of sight (NLOS) conditions, the fact that part of the wireless communication infrastructure has already been deployed and positioned in a way that may not be optimal for positioning purposes, variable humidity conditions, etc. The ultimate goal is to provide a service that may be used to assist people with special needs. We present experimental results based on scene analysis; the main distance metric used was the Euclidean distance but the Mahalanobis distance was also used in one case. The algorithm employed to compare fingerprints was the weighted k-nearest neighbor one. For Wi-Fi, with only three visible access points, accuracy ranged from 3.94 to 4.82 m, and precision from 5.21 to 7.0 m 90% of the time. With respect to BLE, with a low beacon density (1 beacon per 45.7 m2), accuracy ranged from 1.47 to 2.15 m, and precision from 1.81 to 3.58 m 90% of the time. Taking into account the fact that this system is designed to work in real situations in a scenario with high environmental fluctuations, and comparing the results with others obtained in laboratory scenarios, our results are promising and demonstrate that the system would be able to position users with these reasonable values of accuracy and precision. PMID:28587285

Evaluation of a realtime, remote monitoring telemedicine system using the Bluetooth protocol and a mobile phone network.

PubMed

Jasemian, Yousef; Arendt-Nielsen, Lars

2005-01-01

A generic, realtime wireless telemedicine system has been developed that uses the Bluetooth protocol and the general packet radio service for mobile phones. The system was tested on 10 healthy volunteers, by continuous monitoring of their electrocardiograms (ECGs). Under realistic conditions, the system had 96.5% uptime, a data throughput of 3.3 kbit/s, a mean packet error rate of 8.5x10(-3) packet/s and a mean packet loss rate of 8.2x10(-3) packet/s. During 24 h testing, the total average downtime was 66 min and 90% of the periods of downtime were of only 1-3 min duration. Less than 10% of the ECGs were of unacceptable quality. Thus, the generic telemedicine system showed high reliability and performance, and the design may provide a foundation for realtime monitoring in clinical practice, for example in cardiology.

Wireless Control of Miniaturized Mobile Vehicle for Indoor Surveillance

NASA Astrophysics Data System (ADS)

Taha Saquib, Syed M.; Hameed, Sarmad; Usman Ali, Syed M.; Jafri, Raza; Amin, Imran

2013-12-01

This work is based upon electronic automation and Smart Control techniques, which constitute the basis of Control Area Network (CAN) and Personal Area Network (PAN). Bluetooth technology has been interfaced with a programmable controller to provide multi-dimensional vehicle control. A network is proposed which contains a remote, mobile host controller and an android operating system based mobile set (Client). The client communicates with a host controller through a Bluetooth device. The system incorporates duplex communication after successful confirmation between the host and the client; the android based mobile unit controls the vehicle through the Bluetooth module.

Correlation of blood pressure and the ratio of S1 to S2 as measured by esophageal stethoscope and wireless bluetooth transmission.

PubMed

Hoon Lim, Kyoung; Duck Shin, Young; Hi Park, Sang; Ho Bae, Jin; Jae Lee, Hong; Jung Kim, Seon; Yun Shin, Ji; Jin Choi, Young

2013-07-01

Objective : Esophageal stethoscope has the advantage of being non-invasive, easily placed and capability to monitor the heart sound. This study was designed to determine whether the ratio of S1 to S2 analyzed by esophageal stethoscope and wireless bluetooth transmission can be accurate indicator that express the correlation with blood pressure. Total 33 adult male and female without cardiac disorder and with normal heart rhythm were selected randomly as the subjects of this Study. Two microphones were used with one for acquisition of heart sound by connecting it to the esophageal stethoscope while the other was used to measure the background noise in the operating room. After having transmitted the heart sound measured with the esophageal stethoscope to the receiver by using bluetooth module, it was saved in PC and outputted, following removal of noise in the operating room and the respiratory sound. S1 and S2 were measured with computation of the ratio of S1 to S2. Correlations between the systolic blood pressure with each of the S1, S2 and ratio of S1 to S2 were examined by using correlation analysis. The ratio of S1 to S2 displayed the highest correlation with the systolic blood pressure, with S1 and S2 also displaying positive correlation with the systolic blood pressure. As the result of analysis of the heart sound and the systolic blood pressure measured by using the esophageal stethoscope, the radio of S1 to S2 displayed greater correlation with the systolic blood pressure in comparison to the S1.

Circularly polarized triple band glass shaped monopole patch antenna with metallic reflector for bluetooth & wireless applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jangid, K. G.; Kulhar, V. S.; Choudhary, N.

This paper presents the design and performance of strip line fed glass shaped monopole patch antenna having with overall size 30mm × 30 mm × 1.59 mm. In the patch; an eight shaped slot and in the ground plane an eight shaped ring are introduced. A metallic ground plane is also introduced at appropriate location beneath the ground plane. The proposed antenna is simulated by applying CST Microwave Studio simulator. Antenna provides circularly polarized radiations, triple broad impedance bandwidth of 203MHz (2.306GHz to 2.510GHz), 42MHz (2.685GHz to 2.757GHz) & GHz (3.63 GHz to 6.05 GHz), high flat gain (close to 5dBi) and good radiationmore » properties in the desired frequency range. This antenna may be a very useful tool for 2.45GHz Bluetooth communication band as well as for 2.4GHz/5.2 GHz /5.8 GHz WLAN bands & 3.7GHz/5.5 GHz Wi-Max bands.« less

Evaluation of Digital Compressed Sensing for Real-Time Wireless ECG System with Bluetooth low Energy.

PubMed

Wang, Yishan; Doleschel, Sammy; Wunderlich, Ralf; Heinen, Stefan

2016-07-01

In this paper, a wearable and wireless ECG system is firstly designed with Bluetooth Low Energy (BLE). It can detect 3-lead ECG signals and is completely wireless. Secondly the digital Compressed Sensing (CS) is implemented to increase the energy efficiency of wireless ECG sensor. Different sparsifying basis, various compression ratio (CR) and several reconstruction algorithms are simulated and discussed. Finally the reconstruction is done by the android application (App) on smartphone to display the signal in real time. The power efficiency is measured and compared with the system without CS. The optimum satisfying basis built by 3-level decomposed db4 wavelet coefficients, 1-bit Bernoulli random matrix and the most suitable reconstruction algorithm are selected by the simulations and applied on the sensor node and App. The signal is successfully reconstructed and displayed on the App of smartphone. Battery life of sensor node is extended from 55 h to 67 h. The presented wireless ECG system with CS can significantly extend the battery life by 22 %. With the compact characteristic and long term working time, the system provides a feasible solution for the long term homecare utilization.

Ambulatory urodynamic studies (UDS) in children using a Bluetooth-enabled device.

PubMed

Deshpande, Aniruddh V; Craig, Jonathan C; Caldwell, Patrina H Y; Smith, Grahame H H

2012-12-01

• To report the early observations of using ambulatory urodynamic studies (UDS) using a Bluetooth-enabled device in children • To evaluate the incremental value of ambulatory over conventional UDS. • Ambulatory UDS were performed in selected children with voiding dysfunction between August 2009 and October 2010. • Conventional UDS were concurrently performed wherever possible. • The test results and treatment consequences of the two tests were compared. • In all, 12 ambulatory and seven conventional UDS were performed on 10 children (five boys, median [range] age 7 [4-16] years). • Six of the seven children had a normal conventional UDS. Ambulatory UDS detected phasic detrusor overactivity (DO) in five children and generalised DO in one. • Direct correlation of symptoms to DO was possible in two children during ambulatory UDS. Pressure rise during filling, seen in two children on conventional UDS, was not seen during ambulatory UDS. • Five children showed clinical improvement when therapy was guided by ambulatory UDS results. • Ambulatory UDS was generally well tolerated in eight children, with two complaining of discomfort. Inadequate information was obtained in two children who underwent ambulatory UDS due to technical problems in one and distress induced by the UDS in the other. • Ambulatory UDS provides useful additional information over conventional UDS and can be used to guide further therapy in selected children with voiding dysfunction. • It is safe and well tolerated in children. • There is a need for explicit guidance for the technical delivery and interpretation of ambulatory UDS in children. © 2012 THE AUTHORS. BJU INTERNATIONAL © 2012 BJU INTERNATIONAL.

A Low Cost Bluetooth Low Energy Transceiver for Wireless Sensor Network Applications with a Front-end Receiver-Matching Network-Reusing Power Amplifier Load Inductor.

PubMed

Liang, Zhen; Li, Bin; Huang, Mo; Zheng, Yanqi; Ye, Hui; Xu, Ken; Deng, Fangming

2017-04-19

In this work, a low cost Bluetooth Low Energy (BLE) transceiver for wireless sensor network (WSN) applications, with a receiver (RX)-matching network-reusing power amplifier (PA) load inductor, is presented. In order to decrease the die area, only two inductors were used in this work. Besides the one used in the voltage control oscillator (VCO), the PA load inductor was reused as the RX impedance matching component in the front-end. Proper controls have been applied to achieve high transmitter (TX) input impedance when the transceiver is in the receiving mode, and vice versa. This allows the TRX-switch/matching network integration without significant performance degradation. The RX adopted a low-IF structure and integrated a single-ended low noise amplifier (LNA), a current bleeding mixer, a 4th complex filter and a delta-sigma continuous time (CT) analog-to-digital converter (ADC). The TX employed a two-point PLL-based architecture with a non-linear PA. The RX achieved a sensitivity of -93 dBm and consumes 9.7 mW, while the TX achieved a 2.97% error vector magnitude (EVM) with 9.4 mW at 0 dBm output power. This design was fabricated in a 0.11 μm complementary metal oxide semiconductor (CMOS) technology and the front-end circuit only occupies 0.24 mm². The measurement results verify the effectiveness and applicability of the proposed BLE transceiver for WSN applications.

Smartphone-Based Indoor Localization with Bluetooth Low Energy Beacons

PubMed Central

Zhuang, Yuan; Yang, Jun; Li, You; Qi, Longning; El-Sheimy, Naser

2016-01-01

Indoor wireless localization using Bluetooth Low Energy (BLE) beacons has attracted considerable attention after the release of the BLE protocol. In this paper, we propose an algorithm that uses the combination of channel-separate polynomial regression model (PRM), channel-separate fingerprinting (FP), outlier detection and extended Kalman filtering (EKF) for smartphone-based indoor localization with BLE beacons. The proposed algorithm uses FP and PRM to estimate the target’s location and the distances between the target and BLE beacons respectively. We compare the performance of distance estimation that uses separate PRM for three advertisement channels (i.e., the separate strategy) with that use an aggregate PRM generated through the combination of information from all channels (i.e., the aggregate strategy). The performance of FP-based location estimation results of the separate strategy and the aggregate strategy are also compared. It was found that the separate strategy can provide higher accuracy; thus, it is preferred to adopt PRM and FP for each BLE advertisement channel separately. Furthermore, to enhance the robustness of the algorithm, a two-level outlier detection mechanism is designed. Distance and location estimates obtained from PRM and FP are passed to the first outlier detection to generate improved distance estimates for the EKF. After the EKF process, the second outlier detection algorithm based on statistical testing is further performed to remove the outliers. The proposed algorithm was evaluated by various field experiments. Results show that the proposed algorithm achieved the accuracy of <2.56 m at 90% of the time with dense deployment of BLE beacons (1 beacon per 9 m), which performs 35.82% better than <3.99 m from the Propagation Model (PM) + EKF algorithm and 15.77% more accurate than <3.04 m from the FP + EKF algorithm. With sparse deployment (1 beacon per 18 m), the proposed algorithm achieves the accuracies of <3.88 m at 90% of the

Smartphone-Based Indoor Localization with Bluetooth Low Energy Beacons.

PubMed

Zhuang, Yuan; Yang, Jun; Li, You; Qi, Longning; El-Sheimy, Naser

2016-04-26

Indoor wireless localization using Bluetooth Low Energy (BLE) beacons has attracted considerable attention after the release of the BLE protocol. In this paper, we propose an algorithm that uses the combination of channel-separate polynomial regression model (PRM), channel-separate fingerprinting (FP), outlier detection and extended Kalman filtering (EKF) for smartphone-based indoor localization with BLE beacons. The proposed algorithm uses FP and PRM to estimate the target's location and the distances between the target and BLE beacons respectively. We compare the performance of distance estimation that uses separate PRM for three advertisement channels (i.e., the separate strategy) with that use an aggregate PRM generated through the combination of information from all channels (i.e., the aggregate strategy). The performance of FP-based location estimation results of the separate strategy and the aggregate strategy are also compared. It was found that the separate strategy can provide higher accuracy; thus, it is preferred to adopt PRM and FP for each BLE advertisement channel separately. Furthermore, to enhance the robustness of the algorithm, a two-level outlier detection mechanism is designed. Distance and location estimates obtained from PRM and FP are passed to the first outlier detection to generate improved distance estimates for the EKF. After the EKF process, the second outlier detection algorithm based on statistical testing is further performed to remove the outliers. The proposed algorithm was evaluated by various field experiments. Results show that the proposed algorithm achieved the accuracy of <2.56 m at 90% of the time with dense deployment of BLE beacons (1 beacon per 9 m), which performs 35.82% better than <3.99 m from the Propagation Model (PM) + EKF algorithm and 15.77% more accurate than <3.04 m from the FP + EKF algorithm. With sparse deployment (1 beacon per 18 m), the proposed algorithm achieves the accuracies of <3.88 m at 90% of the

Evaluation of bluetooth low power for physiological monitoring in a home based cardiac rehabilitation program.

PubMed

Martin, Timothy; Ding, Hang; D'Souza, Matthew; Karunanithi, Mohan

2012-01-01

Cardiovascular disease (CVD) is the leading cause of mortality in Australia, and places large burdens on the healthcare system. To assist patients with CVDs in recovering from cardiac events and mediating cardiac risk factors, a home based cardiac rehabilitation program, known as the Care Assessment Platform (CAP), was developed. In the CAP program, patients are required to manually enter health information into their mobile phones on a daily basis. The manual operation is often subject to human errors and is inconvenient for some elderly patients. To improve this, an automated wireless solution has been desired. The objectives of this paper are to investigate the feasibility of implementing the newly released Bluetooth 4.0 (BT4.0) for the CAP program, and practically evaluate BT4.0 communications between a developed mobile application and some emulated healthcare devices. The study demonstrated that BT4.0 addresses usability, interoperability and security for healthcare applications, reduces the power consumption in wireless communication, and improves the flexibility of interface for software development. This evaluation study provides an essential mobile BT4.0 framework to incorporate a large range of healthcare devices for clinical assessment and intervention in the CAP program, and hence it is useful for similar development and research work of other mobile healthcare solutions.

Development of novel algorithm and real-time monitoring ambulatory system using Bluetooth module for fall detection in the elderly.

PubMed

Hwang, J Y; Kang, J M; Jang, Y W; Kim, H

2004-01-01

Novel algorithm and real-time ambulatory monitoring system for fall detection in elderly people is described. Our system is comprised of accelerometer, tilt sensor and gyroscope. For real-time monitoring, we used Bluetooth. Accelerometer measures kinetic force, tilt sensor and gyroscope estimates body posture. Also, we suggested algorithm using signals which obtained from the system attached to the chest for fall detection. To evaluate our system and algorithm, we experimented on three people aged over 26 years. The experiment of four cases such as forward fall, backward fall, side fall and sit-stand was repeated ten times and the experiment in daily life activity was performed one time to each subject. These experiments showed that our system and algorithm could distinguish between falling and daily life activity. Moreover, the accuracy of fall detection is 96.7%. Our system is especially adapted for long-time and real-time ambulatory monitoring of elderly people in emergency situation.

Utilization of Connected Vehicle Data to Support Traffic Management Decisions

DOT National Transportation Integrated Search

2018-03-01

Automated vehicle technology is advancing rapidly, from concept to test vehicles on the streets of American cities. Some of the underlying technologies that enable automation, such as Bluetooth communications and GPS, are already available in many ca...

Pervasive technology in Neonatal Intensive Care Unit: a prototype for newborns unobtrusive monitoring.

PubMed

Ciani, Oriana; Piccini, Luca; Parini, Sergio; Rullo, Alessia; Bagnoli, Franco; Marti, Patrizia; Andreoni, Giuseppe

2008-01-01

Pervasive computing research is introducing new perspectives in a wide range of applications, including healthcare domain. In this study we explore the possibility to realize a prototype of a system for unobtrusive recording and monitoring of multiple biological parameters on premature newborns hospitalized in the Neonatal Intensive Care Unit (NICU). It consists of three different units: a sensitized belt for Electrocardiogram (ECG) and chest dilatation monitoring, augmented with extrinsic transducers for temperature and respiratory activity measure, a device for signals pre-processing, sampling and transmission through Bluetooth(R) (BT) technology to a remote PC station and a software for data capture and post-processing. Preliminary results obtained by monitoring babies just discharged from the ward demonstrated the feasibility of the unobtrusive monitoring on this kind of subjects and open a new scenario for premature newborns monitoring and developmental cares practice in NICU.

A paraeducator glove for counting disabled-child behaviors that incorporates a Bluetooth Low Energy wireless link to a smart phone.

PubMed

Luan, Shiwei; Gude, Dana; Prakash, Punit; Warren, Steve

2014-01-01

Behavior tracking with severely disabled children can be a challenge, since dealing directly with a child's behavior is more immediately pressing than the need to record an event for tracking purposes. By the time a paraeducator (`para') is able to break away and record events, behavior counts can be forgotten. This paper presents a paraeducator glove design that can help to track behaviors with minimal distraction by allowing a paraeducator to touch their thumb to one of their other four fingers, where each finger represents a different behavior. Count data are packaged by a microcontroller board on the glove and then sent wirelessly to a smart phone via a Bluetooth Low Energy (BLE) link. A customized BLE profile was designed for this application to promote real-time recording. These data can be forwarded to a database for further analysis. This para glove design addresses basic needs of a wearable device that employs BLE, including local data collection, BLE data transmission, and remote data recording. More functional sensors can be added to this platform to support other wearable scenarios.

The Design of WORKER'S Behavior Analysis Method in Workplace Using Indoor Positioning Technology

NASA Astrophysics Data System (ADS)

Tabata, K.; Konno, H.; Nakajima, M.

2016-06-01

This study presents a method for analyzing workers' behavior using indoor positioning technology and field test in the workplace. Recently, various indoor positioning methods, such as Wi-Fi, Bluetooth low energy (BLE), visible light communication, Japan's indoor messaging system, ultra-wide band (UWB), and pedestrian dead reckoning (PDR), have been investigated. The development of these technologies allows tracking of movement of both people and/or goods in indoor spaces, people and/or goods behavior analysis is expected as one of the key technologies for operation optimization. However, when we use these technologies for human tracking, there are some problem as follows. 1) Many cases need to use dedicated facilities (e.g. UWB). 2) When we use smartphone as sensing device, battery depletion is one of the big problem (especially using PDR). 3) the accuracy is instability for tracking (e.g. Wi-Fi). Based on these matters, in this study we designed and developed an indoor positioning system using BLE positioning. And, we adopted smartphone for business use as sensing device, developed a smartphone application runs on android OS. Moreover, we conducted the field test of developed system at Itoki Corporation's ITOKI Tokyo Innovation Center, SYNQA, office (Tokyo, Japan). Over 40 workers participated in this field test, and worker tracking log data were collected for 6 weeks. We analyzed the characteristics of the workers' behavior using this log data as a prototyping.

Exploring Digital Encounters in the Public Arena

NASA Astrophysics Data System (ADS)

Schieck, Ava Fatah Gen.; Kostakos, Vassilis; Penn, Alan

In this chapter, we explore the types of encounters that technology enables. We consider the differences between digital and nondigital encounters through two pilot studies carried out in the city of Bath, United Kingdom. We investigate how technology can be appropriated for shared interactions that support conscious (or unconscious) social encounters, and highlight the importance of space and the role of place in providing temporal and spatial mechanisms facilitating different types of shared encounters. Here, we apply a method based on intervention through "sensing and projecting" Bluetooth names and digital identity in the public arena, and describe initial observations about people's reaction toward the projection of their Bluetooth names in public. In particular, we note the significance of constructing socially meaningful relations between people mediated by these technologies. We discuss initial results and outline issues raised in detail before finally describing the ongoing work.

Wireless Technology Recognition Based on RSSI Distribution at Sub-Nyquist Sampling Rate for Constrained Devices

PubMed Central

Liu, Wei; Kulin, Merima; Kazaz, Tarik; De Poorter, Eli

2017-01-01

Driven by the fast growth of wireless communication, the trend of sharing spectrum among heterogeneous technologies becomes increasingly dominant. Identifying concurrent technologies is an important step towards efficient spectrum sharing. However, due to the complexity of recognition algorithms and the strict condition of sampling speed, communication systems capable of recognizing signals other than their own type are extremely rare. This work proves that multi-model distribution of the received signal strength indicator (RSSI) is related to the signals’ modulation schemes and medium access mechanisms, and RSSI from different technologies may exhibit highly distinctive features. A distinction is made between technologies with a streaming or a non-streaming property, and appropriate feature spaces can be established either by deriving parameters such as packet duration from RSSI or directly using RSSI’s probability distribution. An experimental study shows that even RSSI acquired at a sub-Nyquist sampling rate is able to provide sufficient features to differentiate technologies such as Wi-Fi, Long Term Evolution (LTE), Digital Video Broadcasting-Terrestrial (DVB-T) and Bluetooth. The usage of the RSSI distribution-based feature space is illustrated via a sample algorithm. Experimental evaluation indicates that more than 92% accuracy is achieved with the appropriate configuration. As the analysis of RSSI distribution is straightforward and less demanding in terms of system requirements, we believe it is highly valuable for recognition of wideband technologies on constrained devices in the context of dynamic spectrum access. PMID:28895879

Wireless Technology Recognition Based on RSSI Distribution at Sub-Nyquist Sampling Rate for Constrained Devices.

PubMed

Liu, Wei; Kulin, Merima; Kazaz, Tarik; Shahid, Adnan; Moerman, Ingrid; De Poorter, Eli

2017-09-12

Driven by the fast growth of wireless communication, the trend of sharing spectrum among heterogeneous technologies becomes increasingly dominant. Identifying concurrent technologies is an important step towards efficient spectrum sharing. However, due to the complexity of recognition algorithms and the strict condition of sampling speed, communication systems capable of recognizing signals other than their own type are extremely rare. This work proves that multi-model distribution of the received signal strength indicator (RSSI) is related to the signals' modulation schemes and medium access mechanisms, and RSSI from different technologies may exhibit highly distinctive features. A distinction is made between technologies with a streaming or a non-streaming property, and appropriate feature spaces can be established either by deriving parameters such as packet duration from RSSI or directly using RSSI's probability distribution. An experimental study shows that even RSSI acquired at a sub-Nyquist sampling rate is able to provide sufficient features to differentiate technologies such as Wi-Fi, Long Term Evolution (LTE), Digital Video Broadcasting-Terrestrial (DVB-T) and Bluetooth. The usage of the RSSI distribution-based feature space is illustrated via a sample algorithm. Experimental evaluation indicates that more than 92% accuracy is achieved with the appropriate configuration. As the analysis of RSSI distribution is straightforward and less demanding in terms of system requirements, we believe it is highly valuable for recognition of wideband technologies on constrained devices in the context of dynamic spectrum access.

[Monitor of ECG signal and heart rate using a mobile phone with Bluetooth communication protocol].

PubMed

Becerra-Luna, Brayans; Dávila-García, Rodrigo; Salgado-Rodríguez, Paola; Martínez-Memije, Raúl; Infante-Vázquez, Oscar

2012-01-01

To develop a portable signal monitoring equipment for electrocardiography (ECG) and heart rate (HR), communicated with a mobile phone using the Bluetooth (BT) communication protocol for display of the signal on screen. A monitoring system was designed in which the electronic section performs the ECG signal acquisition, as well as amplification, filtering, analog to digital conversion and transmission of the ECG and HR using BT. Two programs were developed for the system. The first one calculates HR through QRS identification and sends the ECG signals and HR to the mobile, and the second program is an application to acquire and display them on the mobile screen. We developed a portable electronic system powered by a 9 volt battery, with amplification and bandwidth meeting the international standards for ECG monitoring. The QRS complex identification was performed using the second derivative algorithm, while the programs allow sending and receiving information from the ECG and HR via BT, and viewing it on the mobile screen. The monitoring is feasible within distances of 15 m and it has been tested in various mobiles telephones of brands Nokia®, Sony Ericsson® and Samsung®. This system shows an alternative for mobile monitoring using BT and Java 2 Micro Edition (J2ME) programming. It allows the register of the ECG trace and HR, and it can be implemented in different phones. Copyright © 2011 Instituto Nacional de Cardiología Ignacio Chávez. Published by Masson Doyma México S.A. All rights reserved.

Struggling to Hear? Tiny Devices Can Keep You Connected

MedlinePlus

... features. For example, some can connect to your mobile phone, TV, and other devices using Bluetooth technology. That ... Loss? Hearing Aids Hearing Loss and Hearing Aid Use (Infographic) Assistive Devices for People with Hearing, Voice, ...

Application of travel time information for traffic management.

DOT National Transportation Integrated Search

2012-03-01

This report summarizes findings and implementations of probe vehicle data collection based on Bluetooth MAC address matching : technology. Probe vehicle travel time data are studied in the following field deployment case studies: analysis of traffic ...

Database architecture and query structures for probe data processing.

DOT National Transportation Integrated Search

2012-03-01

This report summarizes findings and implementations of probe vehicle data collection based on Bluetooth MAC address matching technology. Probe vehicle travel time data are studied in the following field deployment case studies: analysis of traffic ch...

Wireless data collection system for travel time estimation and traffic performance evaluation.

DOT National Transportation Integrated Search

2012-05-01

This report presents the results of the third and final research and development project of an implementable wireless : travel time data collection system. Utilizing Bluetooth wireless technology as a platform, the prior projects focused on : data co...

``Low Power Wireless Technologies: An Approach to Medical Applications''

NASA Astrophysics Data System (ADS)

Bellido O., Francisco J.; González R., Miguel; Moreno M., Antonio; de La Cruz F, José Luis

Wireless communication supposed a great both -quantitative and qualitative, jump in the management of the information, allowing the access and interchange of it without the need of a physical cable connection. The wireless transmission of voice and information has remained in constant evolution, arising new standards like BluetoothTM, WibreeTM or ZigbeeTM developed under the IEEE 802.15 norm. These newest wireless technologies are oriented to systems of communication of short-medium distance and optimized for a low cost and minor consume, becoming recognized as a flexible and reliable medium for data communications across a broad range of applications due to the potential that the wireless networks presents to operate in demanding environments providing clear advantages in cost, size, power, flexibility, and distributed intelligence. About the medical applications, the remote health or telecare (also called eHealth) is getting a bigger place into the manufacturers and medical companies, in order to incorporate products for assisted living and remote monitoring of health parameteres. At this point, the IEEE 1073, Personal Health Devices Working Group, stablish the framework for these kind of applications. Particularly, the 1073.3.X describes the physical and transport layers, where the new ultra low power short range wireless technologies can play a big role, providing solutions that allow the design of products which are particularly appropriate for monitor people’s health with interoperability requirements.

PDA-phone-based instant transmission of radiological images over a CDMA network by combining the PACS screen with a Bluetooth-interfaced local wireless link.

PubMed

Kim, Dong Keun; Yoo, Sun K; Park, Jeong Jin; Kim, Sun Ho

2007-06-01

Remote teleconsultation by specialists is important for timely, correct, and specialized emergency surgical and medical decision making. In this paper, we designed a new personal digital assistant (PDA)-phone-based emergency teleradiology system by combining cellular communication with Bluetooth-interfaced local wireless links. The mobility and portability resulting from the use of PDAs and wireless communication can provide a more effective means of emergency teleconsultation without requiring the user to be limited to a fixed location. Moreover, it enables synchronized radiological image sharing between the attending physician in the emergency room and the remote specialist on picture archiving and communication system terminals without distorted image acquisition. To enable rapid and fine-quality radiological image transmission over a cellular network in a secure manner, progressive compression and security mechanisms have been incorporated. The proposed system is tested over a code division Multiple Access 1x-Evolution Data-Only network to evaluate the performance and to demonstrate the feasibility of this system in a real-world setting.

Accuracy of a Basketball Indoor Tracking System Based on Standard Bluetooth Low Energy Channels (NBN23®).

PubMed

Figueira, Bruno; Gonçalves, Bruno; Folgado, Hugo; Masiulis, Nerijus; Calleja-González, Julio; Sampaio, Jaime

2018-06-14

The present study aims to identify the accuracy of the NBN23 ® system, an indoor tracking system based on radio-frequency and standard Bluetooth Low Energy channels. Twelve capture tags were attached to a custom cart with fixed distances of 0.5, 1.0, 1.5, and 1.8 m. The cart was pushed along a predetermined course following the lines of a standard dimensions Basketball court. The course was performed at low speed (<10.0 km/h), medium speed (>10.0 km/h and <20.0 km/h) and high speed (>20.0 km/h). Root mean square error (RMSE) and percentage of variance accounted for (%VAF) were used as accuracy measures. The obtained data showed acceptable accuracy results for both RMSE and %VAF, despite the expected degree of error in position measurement at higher speeds. The RMSE for all the distances and velocities presented an average absolute error of 0.30 ± 0.13 cm with 90.61 ± 8.34 of %VAF, in line with most available systems, and considered acceptable for indoor sports. The processing of data with filter correction seemed to reduce the noise and promote a lower relative error, increasing the %VAF for each measured distance. Research using positional-derived variables in Basketball is still very scarce; thus, this independent test of the NBN23 ® tracking system provides accuracy details and opens up opportunities to develop new performance indicators that help to optimize training adaptations and performance.

Wireless Local Area Network (WLAN) Vulnerability Assessment and Security

DTIC Science & Technology

2005-09-01

even that they have a Bluetooth device to begin with. Bluetooth attacks can permit network sniffing, device detection, data and services theft . Two...the Bluetooth v1.1 Foundation Specifications9. One major security issue is the fact that the Bluetooth standard allows a single device to communicate...simultaneously with multiple other devices . Many Bluetooth radios are embedded in devices and users often do not realize whether they are on or

77 FR 38831 - Antitrust Division

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... Production Act of 1993--Bluetooth Sig, Inc. Notice is hereby given that, on May 30, 2012, pursuant to Section... Act''), Bluetooth SIG, Inc. has filed written notifications simultaneously with the Attorney General... Bluetooth SIG, Inc., Kirkland, WA. The nature and scope of Bluetooth SIG, Inc.'s standards development...

The Effects of Virtual Coaching on Teacher Candidates' Perceptions and Concerns Regarding On-Demand Corrective Feedback

ERIC Educational Resources Information Center

Wake, Donna; Dailey, Debbie; Cotabish, Alicia; Benson, Tammy

2017-01-01

A virtual coaching intervention utilizing Skype and Bluetooth (Bug-in-the-Ear) technology provided immediate corrective feedback to non-traditional teacher candidates during a semester-long internship experience. Participants completed their student teaching internship as a requirement of a teacher preparation program at a mid-size Southeastern…

Parameter Estimation of the Thermal Network Model of a Machine Tool Spindle by Self-made Bluetooth Temperature Sensor Module

PubMed Central

Lo, Yuan-Chieh; Hu, Yuh-Chung; Chang, Pei-Zen

2018-01-01

Thermal characteristic analysis is essential for machine tool spindles because sudden failures may occur due to unexpected thermal issue. This article presents a lumped-parameter Thermal Network Model (TNM) and its parameter estimation scheme, including hardware and software, in order to characterize both the steady-state and transient thermal behavior of machine tool spindles. For the hardware, the authors develop a Bluetooth Temperature Sensor Module (BTSM) which accompanying with three types of temperature-sensing probes (magnetic, screw, and probe). Its specification, through experimental test, achieves to the precision ±(0.1 + 0.0029|t|) °C, resolution 0.00489 °C, power consumption 7 mW, and size Ø40 mm × 27 mm. For the software, the heat transfer characteristics of the machine tool spindle correlative to rotating speed are derived based on the theory of heat transfer and empirical formula. The predictive TNM of spindles was developed by grey-box estimation and experimental results. Even under such complicated operating conditions as various speeds and different initial conditions, the experiments validate that the present modeling methodology provides a robust and reliable tool for the temperature prediction with normalized mean square error of 99.5% agreement, and the present approach is transferable to the other spindles with a similar structure. For realizing the edge computing in smart manufacturing, a reduced-order TNM is constructed by Model Order Reduction (MOR) technique and implemented into the real-time embedded system. PMID:29473877

Parameter Estimation of the Thermal Network Model of a Machine Tool Spindle by Self-made Bluetooth Temperature Sensor Module.

PubMed

Lo, Yuan-Chieh; Hu, Yuh-Chung; Chang, Pei-Zen

2018-02-23

Thermal characteristic analysis is essential for machine tool spindles because sudden failures may occur due to unexpected thermal issue. This article presents a lumped-parameter Thermal Network Model (TNM) and its parameter estimation scheme, including hardware and software, in order to characterize both the steady-state and transient thermal behavior of machine tool spindles. For the hardware, the authors develop a Bluetooth Temperature Sensor Module (BTSM) which accompanying with three types of temperature-sensing probes (magnetic, screw, and probe). Its specification, through experimental test, achieves to the precision ±(0.1 + 0.0029|t|) °C, resolution 0.00489 °C, power consumption 7 mW, and size Ø40 mm × 27 mm. For the software, the heat transfer characteristics of the machine tool spindle correlative to rotating speed are derived based on the theory of heat transfer and empirical formula. The predictive TNM of spindles was developed by grey-box estimation and experimental results. Even under such complicated operating conditions as various speeds and different initial conditions, the experiments validate that the present modeling methodology provides a robust and reliable tool for the temperature prediction with normalized mean square error of 99.5% agreement, and the present approach is transferable to the other spindles with a similar structure. For realizing the edge computing in smart manufacturing, a reduced-order TNM is constructed by Model Order Reduction (MOR) technique and implemented into the real-time embedded system.

Radio Signal Augmentation for Improved Training of a Convolutional Neural Network

DTIC Science & Technology

2016-09-01

official government endorsement or approval of commercial products or services referenced in this report. Bluetooth ® is a registered...trademark of Bluetooth SIG, Inc.. Nuand™ and blade RF™ are trademarks of Nurand, LLC. Released by E. R. Buckland, Head IO Support to National... Bluetooth ® computer mouse, and Bluetooth ® search from a mobile cellular phone. Qualitatively, model Moffset dramatically outperformed model Mclean in

Wireless Security Within Hastily Formed Networks

DTIC Science & Technology

2006-09-01

WLAN DEVICES (STEP ONE) ............34 1. Personal Firewalls..............................................................................34 2. Anti ...includes client devices , access points, network infrastructure, network management, and delivery of mobility services to maintain network security and...Technology Special Publication 800-48, Wireless Network Security, 802.11, Bluetooth , and Handheld Devices . Available at http://csrc.nist.gov

Wireless system for monitoring Intra-abdominal pressure in patient with severe abdominal pathology

NASA Astrophysics Data System (ADS)

Sokolovskiy, S. S.; Shtotskiy, Y. V.; Leljanov, A. D.

2017-01-01

The paper discusses an experimental design of the wireless system for monitoring intra-abdominal pressure (IAP) using Bluetooth Low Energy technology. The possibility of measuring IAP via the bladder using a wireless pressure sensor with a hydrophobic bacteria filter between the liquid transmitting medium and the sensor element is grounded.

Effects of Cyclic Prefix Jamming Versus Noise Jamming in OFDM Signals

DTIC Science & Technology

2011-03-01

is even found in the Bluetooth technology used in something as common as videogame con- trollers. It is now a more universally-accepted standard for...Dec 2009. [Online]. Avail- able: http://www.brighthub.com/electronics/gps/articles/60598.aspx. 8. LTE Product Design, “LTE Benefits v 3.3,” May

A Review of Assistive Listening Device and Digital Wireless Technology for Hearing Instruments

PubMed Central

Kim, Chun Hyeok

2014-01-01

Assistive listening devices (ALDs) refer to various types of amplification equipment designed to improve the communication of individuals with hard of hearing to enhance the accessibility to speech signal when individual hearing instruments are not sufficient. There are many types of ALDs to overcome a triangle of speech to noise ratio (SNR) problems, noise, distance, and reverberation. ALDs vary in their internal electronic mechanisms ranging from simple hard-wire microphone-amplifier units to more sophisticated broadcasting systems. They usually use microphones to capture an audio source and broadcast it wirelessly over a frequency modulation (FM), infra-red, induction loop, or other transmission techniques. The seven types of ALDs are introduced including hardwire devices, FM sound system, infra-red sound system, induction loop system, telephone listening devices, television, and alert/alarm system. Further development of digital wireless technology in hearing instruments will make possible direct communication with ALDs without any accessories in the near future. There are two technology solutions for digital wireless hearing instruments improving SNR and convenience. One is near-field magnetic induction combined with Bluetooth radio frequency (RF) transmission or proprietary RF transmission and the other is proprietary RF transmission alone. Recently launched digital wireless hearing aid applying this new technology can communicate from the hearing instrument to personal computer, phones, Wi-Fi, alert systems, and ALDs via iPhone, iPad, and iPod. However, it comes with its own iOS application offering a range of features but there is no option for Android users as of this moment. PMID:25566400

A review of assistive listening device and digital wireless technology for hearing instruments.

PubMed

Kim, Jin Sook; Kim, Chun Hyeok

2014-12-01

Assistive listening devices (ALDs) refer to various types of amplification equipment designed to improve the communication of individuals with hard of hearing to enhance the accessibility to speech signal when individual hearing instruments are not sufficient. There are many types of ALDs to overcome a triangle of speech to noise ratio (SNR) problems, noise, distance, and reverberation. ALDs vary in their internal electronic mechanisms ranging from simple hard-wire microphone-amplifier units to more sophisticated broadcasting systems. They usually use microphones to capture an audio source and broadcast it wirelessly over a frequency modulation (FM), infra-red, induction loop, or other transmission techniques. The seven types of ALDs are introduced including hardwire devices, FM sound system, infra-red sound system, induction loop system, telephone listening devices, television, and alert/alarm system. Further development of digital wireless technology in hearing instruments will make possible direct communication with ALDs without any accessories in the near future. There are two technology solutions for digital wireless hearing instruments improving SNR and convenience. One is near-field magnetic induction combined with Bluetooth radio frequency (RF) transmission or proprietary RF transmission and the other is proprietary RF transmission alone. Recently launched digital wireless hearing aid applying this new technology can communicate from the hearing instrument to personal computer, phones, Wi-Fi, alert systems, and ALDs via iPhone, iPad, and iPod. However, it comes with its own iOS application offering a range of features but there is no option for Android users as of this moment.

Automatic Identification Technology: Tracking Weapons and Ammunition for the Norwegian Armed Forces

DTIC Science & Technology

2011-06-01

and their error rate. It can also add an anti - theft feature that provides an extra service to the launderers.35 Firms that have problems with...33  Figure 15.  Handheld 2D Matrix Reader with USB and Bluetooth Connections. .............34  Figure 16.  NDLO is...CCD Charge Coupled Device DoD United States Department of Defense EPC Electronic Product Code ERP Enterprise Resource Planning GHz Giga

Security Enhancement of Wireless Sensor Networks Using Signal Intervals.

PubMed

Moon, Jaegeun; Jung, Im Y; Yoo, Jaesoo

2017-04-02

Various wireless technologies, such as RF, Bluetooth, and Zigbee, have been applied to sensor communications. However, the applications of Bluetooth-based wireless sensor networks (WSN) have a security issue. In one pairing process during Bluetooth communication, which is known as simple secure pairing (SSP), the devices are required to specify I/O capability or user interference to prevent man-in-the-middle (MITM) attacks. This study proposes an enhanced SSP in which a nonce to be transferred is converted to a corresponding signal interval. The quantization level, which is used to interpret physical signal intervals, is renewed at every connection by the transferred nonce and applied to the next nonce exchange so that the same signal intervals can represent different numbers. Even if attackers eavesdrop on the signals, they cannot understand what is being transferred because they cannot determine the quantization level. Furthermore, the proposed model does not require exchanging passkeys as data, and the devices are secure in the case of using a fixed PIN. Subsequently, the new quantization level is calculated automatically whenever the same devices attempt to connect with each other. Therefore, the pairing process can be protected from MITM attacks and be convenient for users.

Analysis of bluetooth and wi-fi technology to measure wait times of personal vehicles at Arizona-Mexico ports of entry : [executive summary].

DOT National Transportation Integrated Search

2015-11-01

The Arizona Department of Transportation (ADOT), Office of P3 Initiatives and International : Affairs selected Lee Engineering to analyze the penetration rate of Anonymous Re-Identification : (ARID) technology to measure wait time of U.S. and Mexico ...

a Statistical Analysis on the System Performance of a Bluetooth Low Energy Indoor Positioning System in a 3d Environment

NASA Astrophysics Data System (ADS)

Haagmans, G. G.; Verhagen, S.; Voûte, R. L.; Verbree, E.

2017-09-01

Since GPS tends to fail for indoor positioning purposes, alternative methods like indoor positioning systems (IPS) based on Bluetooth low energy (BLE) are developing rapidly. Generally, IPS are deployed in environments covered with obstacles such as furniture, walls, people and electronics influencing the signal propagation. The major factor influencing the system performance and to acquire optimal positioning results is the geometry of the beacons. The geometry of the beacons is limited to the available infrastructure that can be deployed (number of beacons, basestations and tags), which leads to the following challenge: Given a limited number of beacons, where should they be placed in a specified indoor environment, such that the geometry contributes to optimal positioning results? This paper aims to propose a statistical model that is able to select the optimal configuration that satisfies the user requirements in terms of precision. The model requires the definition of a chosen 3D space (in our case 7 × 10 × 6 meter), number of beacons, possible user tag locations and a performance threshold (e.g. required precision). For any given set of beacon and receiver locations, the precision, internal- and external reliability can be determined on forehand. As validation, the modeled precision has been compared with observed precision results. The measurements have been performed with an IPS of BlooLoc at a chosen set of user tag locations for a given geometric configuration. Eventually, the model is able to select the optimal geometric configuration out of millions of possible configurations based on a performance threshold (e.g. required precision).

Angelcare mobile system: homecare patient monitoring using bluetooth and GPRS.

PubMed

Ribeiro, Anna G D; Maitelli, Andre L; Valentim, Ricardo A M; Brandao, Glaucio B; Guerreiro, Ana M G

2010-01-01

The quick progress in technology has brought new paradigms to the computing area, bringing with them many benefits to society. The paradigm of ubiquitous computing brings innovations applying computing in people's daily life without being noticed. For this, it has used the combination of several existing technologies like wireless communications and sensors. Several of the benefits have reached the medical area, bringing new methods of surgery, appointments and examinations. This work presents telemedicine software that adds the idea of ubiquity to the medical area, innovating the relation between doctor and patient. It also brings security and confidence to a patient being monitored in homecare.

Security Enhancement of Wireless Sensor Networks Using Signal Intervals

PubMed Central

Moon, Jaegeun; Jung, Im Y.; Yoo, Jaesoo

2017-01-01

Various wireless technologies, such as RF, Bluetooth, and Zigbee, have been applied to sensor communications. However, the applications of Bluetooth-based wireless sensor networks (WSN) have a security issue. In one pairing process during Bluetooth communication, which is known as simple secure pairing (SSP), the devices are required to specify I/O capability or user interference to prevent man-in-the-middle (MITM) attacks. This study proposes an enhanced SSP in which a nonce to be transferred is converted to a corresponding signal interval. The quantization level, which is used to interpret physical signal intervals, is renewed at every connection by the transferred nonce and applied to the next nonce exchange so that the same signal intervals can represent different numbers. Even if attackers eavesdrop on the signals, they cannot understand what is being transferred because they cannot determine the quantization level. Furthermore, the proposed model does not require exchanging passkeys as data, and the devices are secure in the case of using a fixed PIN. Subsequently, the new quantization level is calculated automatically whenever the same devices attempt to connect with each other. Therefore, the pairing process can be protected from MITM attacks and be convenient for users. PMID:28368341

Towards smart environments using smart objects.

PubMed

Sedlmayr, Martin; Prokosch, Hans-Ulrich; Münch, Ulli

2011-01-01

Barcodes, RFID, WLAN, Bluetooth and many more technologies are used in hospitals. They are the technological bases for different applications such as patient monitoring, asset management and facility management. However, most of these applications exist side by side with hardly any integration and even interoperability is not guaranteed. Introducing the concept of smart objects inspired by the Internet of Things can improve the situation by separating the capabilities and functions of an object from the implementing technology such as RFID or WLAN. By aligning technological and business developments smart objects have the power to transform a hospital from an agglomeration of technologies into a smart environment.

Situated Computing: The Next Frontier for HCI Research

DTIC Science & Technology

2002-01-01

population works and lives with information. Most individuals interact with information through a single portal: a personal desktop or laptop...of single devices, nor will one person necessarily own each device. This leap of imagination requires that human-computer interaction (HCI...wireless technologies, including Bluetooth [16], IrDA [22] (Infrared Data Association- standards for infrared communications) and HomeRF TM [21

Exposure caused by wireless technologies used for short-range indoor communication in homes and offices.

PubMed

Schmid, G; Lager, D; Preiner, P; Uberbacher, R; Cecil, S

2007-01-01

In order to estimate typical radio frequency exposures from indoor used wireless communication technologies applied in homes and offices, WLAN, Bluetooth and Digital Enhanced Cordless Telecommunications systems, as well as baby surveillance devices and wireless headphones for indoor usage, have been investigated by measurements and numerical computations. Based on optimised measurement methods, field distributions and resulting exposure were assessed on selected products and real exposure scenarios. Additionally, generic scenarios have been investigated on the basis of numerical computations. The obtained results demonstrate that under usual conditions the resulting spatially (over body dimensions) averaged and 6-min time-averaged exposure for persons in the radio frequency fields of the considered applications is below approximately 0.1% of the reference level for power density according to the International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines published in 1998. Spatial and temporal peak values can be considerably higher by 2-3 orders of magnitude. In case of some transmitting devices operated in close proximity to the body (e.g. WLAN transmitters), local exposure can reach the same order of magnitude as the basic restriction; however, none of the devices considered in this study exceeded the limits according to the ICNIRP guidelines.

C2 at the Edge: Operating in a Disconnected Low-Bandwidth Environment

DTIC Science & Technology

2015-06-01

using their embedded Bluetooth communications capability. This thesis tests the throughput of the system at the maximum connection distances between...users with real-time chat capability of all locally available devices. 14. SUBJECT TERMS Infrastructure-less, mobile, network, Bluetooth , scatternet...thesis aims to create a communications network of smart devices, using their embedded Bluetooth communica- tions capability. This thesis tests the

Data Flow Infrastructure Initiative (DFII): Coupling Inventory Practices and Data collection Technology to Enhance Research Productivity and Information Access

NASA Astrophysics Data System (ADS)

Meyer, K.; Malin, R.; Rich, R. L.; Pierce, S. A.

2011-12-01

Shortening the cycle from data collection to research publications is a competitive advantage for researchers. Existing technologies for inventory systems such as UPC barcoding systems can be coupled with flexible mobile or handheld devices to advance efficiency, productivity, automation, and integrity in data flows, from data collection to sample processing to database management and analysis, and finally publication. At the University of Texas, the Data Flow Infrastructure Initiative (DFII) has introduced handheld devices with integrated barcode scanners as a mechanism to enhance research productivity and information access. These devices are established technology and provide a flexible but consistent platform for research data collection and data management. They are not in widespread use yet in the research community. Additional application benefits will accrue by using handheld devices to deliver data on demand in teaching applications. Introducing research scientists, graduate students, and the UT community to the merits and flexibility of these data collection technologies will provide avenues for innovation as well as improving efficiency. The objective of this project is to bring the technology and expertise with handheld systems to a diverse set of pilot projects and establish proficiency at The University of Texas at Austin necessary for widespread application. We have implemented a pilot project in three research labs covering the fields of microbial ecology, water resources decision support, and biogeochemistry to introduce these technologies. We used NautizX5 handheld devices that feature: barcode scanning, bluetooth, stylus, and keypad data inputs coupled with Pendragon Forms Software, a program that allows users to create custom data collection forms structured into an SQL or Access platform thus allowing concurrent data management, data collection and analysis in field and lab settings. Results include the elimination of most manual data entry

Application of near field communication for health monitoring in daily life.

PubMed

Strömmer, Esko; Kaartinen, Jouni; Pärkkä, Juha; Ylisaukko-Oja, Arto; Korhonen, Ilkka

2006-01-01

We study the possibility of applying an emerging RFID-based communication technology, NFC (Near Field Communication), to health monitoring. We suggest that NFC is, compared to other competing technologies, a high-potential technology for short-range connectivity between health monitoring devices and mobile terminals. We propose practices to apply NFC to some health monitoring applications and study the benefits that are attainable with NFC. We compare NFC to other short-range communication technologies such as Bluetooth and IrDA, and study the possibility of improving the usability of health monitoring devices with NFC. We also introduce a research platform for technical evaluation, applicability study and application demonstrations of NFC.

High Speed Internet Access Using Cellular Infrastructure

DTIC Science & Technology

2004-09-01

62 Figure 50 Initial Connection from Laptop to Mobile Phone via Bluetooth . ....................64 Figure 51 Mobile Phone Discovered by the Laptop...tailor them to their needs. Other hardware improvements include Infrared and Bluetooth capabilities for external connectivity with a computer, as well...mobile phone can communicate with a computer through a phone’s vendor specific cable, Infrared or Bluetooth . The latter two depend on both devices

The Modular Clock Algorithm for Blind Rendezvous

DTIC Science & Technology

2009-03-26

and Computer Engineering Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training...capabilities in spectrum management and particularly in harvesting unused portions of pre-allocated band- width under DSA. The term “cognitive radio” was...of rendezvous and our role as the waiter . However, if the “child” refuses to move from non-common spectrum, rendezvous cannot occur. Bluetooth

Wearable wireless photoplethysmography sensors

NASA Astrophysics Data System (ADS)

Spigulis, Janis; Erts, Renars; Nikiforovs, Vladimirs; Kviesis-Kipge, Edgars

2008-04-01

Wearable health monitoring sensors may support early detection of abnormal conditions and prevention of their consequences. Recent designs of three wireless photoplethysmography monitoring devices embedded in hat, glove and sock, and connected to PC or mobile phone by means of the Bluetooth technology, are described. First results of distant monitoring of heart rate and pulse wave transit time using the newly developed devices are presented.

BreathBased Monitoring of Pilot Hypoxia - Proof of Concept

DTIC Science & Technology

2016-04-21

vest, and there are no aircraft connections required. Operation is entirely automatic and data visualization is available via a Bluetooth connected...to USB-connected Flash-RAM (storage depends on module size, 32Gb supported). • Bluetooth transmission of data in real time • Automated storage...via an Android tablet (Figure 4). The tablet acquires the data transmitted using Bluetooth by the pilot worn system module and provides a real-time

Defining a Technical Basis for Comparing and Contrasting Emerging Dynamic Discovery Protocols

DTIC Science & Technology

2001-05-02

UPnP, SLP, Bluetooth , and HAVi • Projected specific UML models for Jini, UPnP, and SLP • Completed a Rapide Model of Jini structure, function, and...narrow application focus but targeting a different application domain. (e.g., HAVi, Salutation Consortium, and Bluetooth Service Discovery) • Sun has...Our General Approach? 1/31/2002 7 Particulars of Our Approach Define a Generic UML Model that Encompasses Jini, UPnP, SLP, HAVi, and Bluetooth

Traffic light detection and intersection crossing using mobile computer vision

NASA Astrophysics Data System (ADS)

Grewei, Lynne; Lagali, Christopher

2017-05-01

The solution for Intersection Detection and Crossing to support the development of blindBike an assisted biking system for the visually impaired is discussed. Traffic light detection and intersection crossing are key needs in the task of biking. These problems are tackled through the use of mobile computer vision, in the form of a mobile application on an Android phone. This research builds on previous Traffic Light detection algorithms with a focus on efficiency and compatibility on a resource-limited platform. Light detection is achieved through blob detection algorithms utilizing training data to detect patterns of Red, Green and Yellow in complex real world scenarios where multiple lights may be present. Also, issues of obscurity and scale are addressed. Safe Intersection crossing in blindBike is also discussed. This module takes a conservative "assistive" technology approach. To achieve this blindBike use's not only the Android device but, an external bike cadence Bluetooth/Ant enabled sensor. Real world testing results are given and future work is discussed.

Validation of a real-time wireless telemedicine system, using bluetooth protocol and a mobile phone, for remote monitoring patient in medical practice.

PubMed

Yousef, Jasemian; Lars, A N

2005-06-22

This paper validates the integration of a generic real-time wireless telemedicine system utilising Global System for Mobile Communications (GSM), BLUETOOTH protocol and General Packet Radio Service (GPRS) for cellular network in clinical practice. In the first experiment, the system was tested on 24 pacemaker patients at Aalborg Hospital (Denmark), in order to see if the pacemaker implant would be affected by the system. I the second experiment, the system was tested on 15 non risky arrhythmia heart patients, in order to evaluate and validate the system application in clinical practice, for patient monitoring. Electrocardiograms were selected as the continuously monitored parameter in the present study. The results showed that the system had no negative effects on the pacemaker implants. The experiment results showed, that in a realistic environment for the patients, the system had 96.1 % up-time, 3.2 (kbps) throughput, 10(-3) (packet/s) Packet Error Rate and 10(-3) (packet/s) Packet Lost Rate. During 24 hours test the network did not respond for 57 minutes, from which 83.1 % was in the range of 0-3 minutes, 15.4 % was in the range of 3-5 minutes, and only 0.7 % of the down-time was > or = 5 and < or = 6 minutes. By a subjective evaluation, it was demonstrated that the system is applicable and the patients as well as the healthcare personals were highly confident with the system. Moreover, the patients had high degree of mobility and freedom, employing the system. In conclusion, this generic telemedicine system showed a high reliability, quality and performance, and the design can provide a basic principle for real-time wireless remote monitoring systems used in clinical practice.

Wireless sensor and data transmission needs and technologies for patient monitoring in the operating room and intensive care unit.

PubMed

Paksuniemi, M; Sorvoja, H; Alasaarela, E; Myllyla, R

2005-01-01

In the intensive care unit, or during anesthesia, patients are attached to monitors by cables. These cables obstruct nursing staff and hinder the patients from moving freely in the hospital. However, rapidly developing wireless technologies are expected to solve these problems. To this end, this study revealed problem areas in current patient monitoring and established the most important medical parameters to monitor. In addition, usable wireless techniques for short-range data transmission were explored and currently employed wireless applications in the hospital environment were studied. The most important parameters measured of the patient include blood pressures, electrocardiography, respiration rate, heart rate and temperature. Currently used wireless techniques in hospitals are based on the WMTS and WLAN standards. There are no viable solutions for short-range data transmission from patient sensors to patient monitors, but potentially usable techniques in the future are based on the WPAN standards. These techniques include Bluetooth, ZigBee and UWB. Other suitable techniques might be based on capacitive or inductive coupling. The establishing of wireless techniques depends on ensuring the reliability of data transmission, eliminating disturbance by other wireless devices, ensuring patient data security and patient safety, and lowering the power consumption and price.

Validating Mobile Electroencephalographic Systems for Integration into the PhyCORE and Application in Clinical Settings

DTIC Science & Technology

2016-09-26

placement. The preamplifier mounted on top of the headset samples EEG signals at 300 Hz; it then transmits the raw EEG data via Bluetooth ® to a data...The preamplifier mounted on the back of the headset samples EEG signals at 256 Hz and then transmits the raw EEG data via Bluetooth ® to a data...electrooculography. The batteries will last 6 hours using Bluetooth ® or 16 hours if data are recorded directly onto a secure digital card. A three-axis

Adopting Energy Efficiency in Connected Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christensen, Dane T; Kemper, Emily

This presentation on connected homes was presented at the 11th Rocky Mountain Utility Efficiency Exchange on September 28, 2017. The discussion covered the integration of energy efficiency measures and practices with Internet of Things (IoT) awareness and adoption of smart technologies and services via WiFi/ Bluetooth enabled home and office equipment. The presentation also describes the benefits to the home and business and benefits/challenges for the utility/implementer.

A persuasive toothbrush to enhance oral hygiene adherence.

PubMed

Walji, Muhammad F; Coker, Ololade; Valenza, John A; Henson, Harold; Warren-Morris, Donna; Zhong, Lin

2008-11-06

In this research we propose that a real-time wireless monitoring and reminder system can assist patients in maintaining optimal oral health. We provide a conceptual framework that incorporates both the behavioral and technical aspects of the proposed system. Further we present preliminary results of a feasibility experiment of modifying an inexpensive electric toothbrush by attaching an accelerometer and determining the ability to track motion and time by wirelessly transmitting data via Bluetooth technology.

Analog design of wireless control for home equipment

NASA Astrophysics Data System (ADS)

Zheng, Shiyong; Li, Zhao; Li, Biqing; Jiang, Suping

2018-04-01

This design consists of a STC89C52 microcontroller, a serial Bluetooth module and the Android system. Production of STC89C52 controlled by single-chip computer telephone systems. The system is composed of mobile phone Android system as a master in the family centre,via serial Bluetooth module pass instructions and information to implement wireless transceiver using STC89C52 MCU wireless Bluetooth transmission to control homedevices. System high reliability, low cost easy to use, stong applicability and other characerristics, can be used in single-user family, has great significance.

Power-Constrained Fuzzy Logic Control of Video Streaming over a Wireless Interconnect

NASA Astrophysics Data System (ADS)

Razavi, Rouzbeh; Fleury, Martin; Ghanbari, Mohammed

2008-12-01

Wireless communication of video, with Bluetooth as an example, represents a compromise between channel conditions, display and decode deadlines, and energy constraints. This paper proposes fuzzy logic control (FLC) of automatic repeat request (ARQ) as a way of reconciling these factors, with a 40% saving in power in the worst channel conditions from economizing on transmissions when channel errors occur. Whatever the channel conditions are, FLC is shown to outperform the default Bluetooth scheme and an alternative Bluetooth-adaptive ARQ scheme in terms of reduced packet loss and delay, as well as improved video quality.

Bluetooth traffic detectors for use as permanently installed travel time instruments : [summary].

DOT National Transportation Integrated Search

2012-02-01

In support of the Maryland State Highway Administration (SHA) business objectives : related to mobility and congestion relief, in 2009 the University of Marylands (UMD) : Center for Advanced Transportation Technology (CATT) proposed to develop the...

Application of Bluetooth technology to rural freeway speed data collection ; executive summary report.

DOT National Transportation Integrated Search

2012-10-01

The Ohio Department of Transportation (ODOT) currently employs a network of side fire speed radar devices to measure travel speeds and travel times on their interstate network. While these devices measure the instantaneous spot speed, segment level s...

An Intelligent Sensor System for Monitoring Fatigue Damage in Welded Steel Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernandes, B.; Gaydecki, P.; Burdekin, F. Michael

A system for monitoring fatigue damage in steel components is described. The sensor, a thin steel sheet with a pre-crack in it, is attached to the component. Its crack length increases by fatigue in service and is recorded using a microcontroller. Measurement is accomplished using conductive tracks in a circuit whose output voltage changes when the crack propagates past a track. Data stored in memory can be remotely downloaded using Bluetooth{sup TM} technology to a PC.

Design of a Wireless EEG System for Point-of-Care Applications.

PubMed

Jia, Wenyan; Bai, Yicheng; Sun, Mingui; Sclabassi, Robert J

2013-04-01

This study aims to develop a wireless EEG system to provide critical point-of-care information about brain electrical activity. A novel dry electrode, which can be installed rapidly, is used to acquire EEG from the scalp. A wireless data link between the electrode and a data port (i.e., a smartphone) is established based on the Bluetooth technology. A prototype of this system has been implemented and its performance in acquiring EEG has been evaluated.

Connecting, Protecting, and Informing the Next Generation of First Responders

DTIC Science & Technology

2015-12-10

SLED is the Bluetooth Indoor Proximity System (BLIPS) that uses beacons to track first responders’ progress through indoor spaces. As first...Outfitting BLIPS with Bluetooth and Wi-Fi capability became a learning experience for two co- operative education students from Rensselaer Polytechnic

Automated Robot Movement in the Mapped Area Using Fuzzy Logic for Wheel Chair Application

NASA Astrophysics Data System (ADS)

Siregar, B.; Efendi, S.; Ramadhana, H.; Andayani, U.; Fahmi, F.

2018-03-01

The difficulties of the disabled to move make them unable to live independently. People with disabilities need supporting device to move from place to place. For that, we proposed a solution that can help people with disabilities to move from one room to another automatically. This study aims to create a wheelchair prototype in the form of a wheeled robot as a means to learn the automatic mobilization. The fuzzy logic algorithm was used to determine motion direction based on initial position, ultrasonic sensors reading in avoiding obstacles, infrared sensors reading as a black line reader for the wheeled robot to move smooth and smartphone as a mobile controller. As a result, smartphones with the Android operating system can control the robot using Bluetooth. Here Bluetooth technology can be used to control the robot from a maximum distance of 15 meters. The proposed algorithm was able to work stable for automatic motion determination based on initial position, and also able to modernize the wheelchair movement from one room to another automatically.

Evaluation of Physiologically-Based Artificial Neural Network Models to Detect Operator Workload in Remotely Piloted Aircraft Operations

DTIC Science & Technology

2016-07-13

to a computer via Bluetooth . Respiration is captured as a breathing waveform signal using a capacitive pressure sensor, sampled at 18 Hz. The...dropouts in the Bluetooth signal and artifacts caused by body movement. Workload models. Four artificial neural network models were created using

The Cybersecurity Challenge in Acquisition

DTIC Science & Technology

2016-04-30

problems. Scarier yet, another group took control of a car’s computers through a cellular telephone and Bluetooth connections and could access...did more extensive work, hacking their way into a 2009 midsize car through its cellular, Bluetooth , and other wireless connections. Stefan Savage, a

Competition in the domain of wireless networks security

NASA Astrophysics Data System (ADS)

Bednarczyk, Mariusz

2017-04-01

Wireless networks are very popular and have found wide spread usage amongst various segments, also in military environment. The deployment of wireless infrastructures allow to reduce the time it takes to install and dismantle communications networks. With wireless, users are more mobile and can easily get access to the network resources all the time. However, wireless technologies like WiFi or Bluetooth have security issues that hackers have extensively exploited over the years. In the paper several serious security flaws in wireless technologies are presented. Most of them enable to get access to the internal networks and easily carry out man-in-the-middle attacks. Very often, they are used to launch massive denial of service attacks that target the physical infrastructure as well as the RF spectrum. For instance, there are well known instances of Bluetooth connection spoofing in order to steal WiFi password stored in the mobile device. To raise the security awareness and protect wireless networks against an adversary attack, an analysis of attack methods and tools over time is presented in the article. The particular attention is paid to the severity, possible targets as well as the ability to persist in the context of protective measures. Results show that an adversary can take complete control of the victims' mobile device features if the users forget to use simple safety principles.

Multi-Residential Activity Labelling in Smart Homes with Wearable Tags Using BLE Technology.

PubMed

Mokhtari, Ghassem; Anvari-Moghaddam, Amjad; Zhang, Qing; Karunanithi, Mohanraj

2018-03-19

Smart home platforms show promising outcomes to provide a better quality of life for residents in their homes. One of the main challenges that exists with these platforms in multi-residential houses is activity labeling. As most of the activity sensors do not provide any information regarding the identity of the person who triggers them, it is difficult to label the sensor events in multi-residential smart homes. To deal with this challenge, individual localization in different areas can be a promising solution. The localization information can be used to automatically label the activity sensor data to individuals. Bluetooth low energy (BLE) is a promising technology for this application due to how easy it is to implement and its low energy footprint. In this approach, individuals wear a tag that broadcasts its unique identity (ID) in certain time intervals, while fixed scanners listen to the broadcasting packet to localize the tag and the individual. However, the localization accuracy of this method depends greatly on different settings of broadcasting signal strength, and the time interval of BLE tags. To achieve the best localization accuracy, this paper studies the impacts of different advertising time intervals and power levels, and proposes an efficient and applicable algorithm to select optimal value settings of BLE sensors. Moreover, it proposes an automatic activity labeling method, through integrating BLE localization information and ambient sensor data. The applicability and effectiveness of the proposed structure is also demonstrated in a real multi-resident smart home scenario.

Mobile access to the Internet: from personal bubble to satellites

NASA Astrophysics Data System (ADS)

Gerla, Mario

2001-10-01

Mobile, wireless access and networking has emerged in the last few years as one of the most important directions of Internet growth. The popularity of mobile, and, more generally, nomadic Internet access is due to many enabling factors including: (a) emergence of meaningful applications tailored to the individual on the move; (b) small form factor and long battery life; (c) efficient middleware designed to support mobility; and, (d) efficient wireless networking technologies. A key player in the mobile Internet access is the nomad, i.e. the individual equipped with various computing and I/O gadgets (cellular phone, earphones, GPS navigator, palm pilot, beeper, portable scanner, digital camera, etc.). These devices form his/her Personal Area Network or PAN or personal bubble. The connectivity within the bubble is wireless (using for example a low cost, low power wireless LAN such as Bluetooth). The bubble can expand and contract dynamically depending on needs. It may temporarily include sensors and actuators as the nomad walks into a new environment. In this paper, we identify the need for the interconnection of the PAN with other wireless networks in order to achieve costeffective mobile access to the Internet. We will overview some key networking technologies required to support the PAN (eg, Bluetooth). We will also discuss an emerging technology, Ad Hoc wireless networking which is the natural complement of the PAN in sparsely populated areas. Finally, we will identify the need for intelligent routers to assist the mobile user in the selection of the best Internet access strategy.

Adaptive Training and Collective Decision Support Based on Man-Machine Interface

DTIC Science & Technology

2016-03-02

Emotiv Inc., Figure 1) for collection of EEG data. This device is wireless and transmits data via Bluetooth to a PC using a USB dongle. The... Bluetooth to a PC using a USB dongle. The advantage of the system over others is the ability to collect high resolution EEG data without complicated

Spontaneous Group Learning in Ambient Learning Environments

NASA Astrophysics Data System (ADS)

Bick, Markus; Jughardt, Achim; Pawlowski, Jan M.; Veith, Patrick

Spontaneous Group Learning is a concept to form and facilitate face-to-face, ad-hoc learning groups in collaborative settings. We show how to use Ambient Intelligence to identify, support, and initiate group processes. Learners' positions are determined by widely used technologies, e.g., Bluetooth and WLAN. As a second step, learners' positions, tasks, and interests are visualized. Finally, a group process is initiated supported by relevant documents and services. Our solution is a starting point to develop new didactical solutions for collaborative processes.

DreamTel; Diabetes risk evaluation and management tele-monitoring study protocol.

PubMed

Tobe, Sheldon W; Wentworth, Joan; Ironstand, Laurie; Hartman, Susan; Hoppe, Jackie; Whiting, Judi; Kennedy, Janice; McAllister, Colin; Kiss, Alex; Perkins, Nancy; Vincent, Lloyd; Pylypchuk, George; Lewanczuk, Richard Z

2009-05-09

The rising prevalence of type 2 diabetes underlines the importance of secondary strategies for the prevention of target organ damage. While access to diabetes education centers and diabetes intensification management has been shown to improve blood glucose control, these services are not available to all that require them, particularly in rural and northern areas. The provision of these services through the Home Care team is an advance that can overcome these barriers. Transfer of blood glucose data electronically from the home to the health care provider may improve diabetes management. The study population will consist of patients with type 2 diabetes with uncontrolled A1c levels living on reserve in the Battlefords region of Saskatchewan, Canada. This pilot study will take place over three phases. In the first phase over three months the impact of the introduction of the Bluetooth enabled glucose monitor will be assessed. In the second phase over three months, the development of guidelines based treatment algorithms for diabetes intensification will be completed. In the third phase lasting 18 months, study subjects will have diabetes intensification according to the algorithms developed. The first phase will determine if the use of the Bluetooth enabled blood glucose devices which can transmit results electronically will lead to changes in A1c levels. It will also determine the feasibility of recruiting subjects to use this technology. The rest of the Diabetes Risk Evaluation and Management Tele-monitoring (DreamTel) study will determine if the delivery of a diabetes intensification management program by the Home Care team supported by the Bluetooth enabled glucose meters leads to improvements in diabetes management. Protocol NCT00325624.

Low-cost, smartphone based frequency doubling technology visual field testing using virtual reality (Conference Presentation)

NASA Astrophysics Data System (ADS)

Alawa, Karam A.; Sayed, Mohamed; Arboleda, Alejandro; Durkee, Heather A.; Aguilar, Mariela C.; Lee, Richard K.

2017-02-01

Glaucoma is the leading cause of irreversible blindness worldwide. Due to its wide prevalence, effective screening tools are necessary. The purpose of this project is to design and evaluate a system that enables portable, cost effective, smartphone based visual field screening based on frequency doubling technology. The system is comprised of an Android smartphone to display frequency doubling stimuli and handle processing, a Bluetooth remote for user input, and a virtual reality headset to simulate the exam. The LG Nexus 5 smartphone and BoboVR Z3 virtual reality headset were used for their screen size and lens configuration, respectively. The system is capable of running the C-20, N-30, 24-2, and 30-2 testing patterns. Unlike the existing system, the smartphone FDT tests both eyes concurrently by showing the same background to both eyes but only displaying the stimulus to one eye at a time. Both the Humphrey Zeiss FDT and the smartphone FDT were tested on five subjects without a history of ocular disease with the C-20 testing pattern. The smartphone FDT successfully produced frequency doubling stimuli at the correct spatial and temporal frequency. Subjects could not tell which eye was being tested. All five subjects preferred the smartphone FDT to the Humphrey Zeiss FDT due to comfort and ease of use. The smartphone FDT is a low-cost, portable visual field screening device that can be used as a screening tool for glaucoma.

Multi-Residential Activity Labelling in Smart Homes with Wearable Tags Using BLE Technology

PubMed Central

Mokhtari, Ghassem; Zhang, Qing; Karunanithi, Mohanraj

2018-01-01

Smart home platforms show promising outcomes to provide a better quality of life for residents in their homes. One of the main challenges that exists with these platforms in multi-residential houses is activity labeling. As most of the activity sensors do not provide any information regarding the identity of the person who triggers them, it is difficult to label the sensor events in multi-residential smart homes. To deal with this challenge, individual localization in different areas can be a promising solution. The localization information can be used to automatically label the activity sensor data to individuals. Bluetooth low energy (BLE) is a promising technology for this application due to how easy it is to implement and its low energy footprint. In this approach, individuals wear a tag that broadcasts its unique identity (ID) in certain time intervals, while fixed scanners listen to the broadcasting packet to localize the tag and the individual. However, the localization accuracy of this method depends greatly on different settings of broadcasting signal strength, and the time interval of BLE tags. To achieve the best localization accuracy, this paper studies the impacts of different advertising time intervals and power levels, and proposes an efficient and applicable algorithm to select optimal value settings of BLE sensors. Moreover, it proposes an automatic activity labeling method, through integrating BLE localization information and ambient sensor data. The applicability and effectiveness of the proposed structure is also demonstrated in a real multi-resident smart home scenario. PMID:29562666

Near Field Communication-based telemonitoring with integrated ECG recordings.

PubMed

Morak, J; Kumpusch, H; Hayn, D; Leitner, M; Scherr, D; Fruhwald, F M; Schreier, G

2011-01-01

Telemonitoring of vital signs is an established option in treatment of patients with chronic heart failure (CHF). In order to allow for early detection of atrial fibrillation (AF) which is highly prevalent in the CHF population telemonitoring programs should include electrocardiogram (ECG) signals. It was therefore the aim to extend our current home monitoring system based on mobile phones and Near Field Communication technology (NFC) to enable patients acquiring their ECG signals autonomously in an easy-to-use way. We prototypically developed a sensing device for the concurrent acquisition of blood pressure and ECG signals. The design of the device equipped with NFC technology and Bluetooth allowed for intuitive interaction with a mobile phone based patient terminal. This ECG monitoring system was evaluated in the course of a clinical pilot trial to assess the system's technical feasibility, usability and patient's adherence to twice daily usage. 21 patients (4f, 54 ± 14 years) suffering from CHF were included in the study and were asked to transmit two ECG recordings per day via the telemonitoring system autonomously over a monitoring period of seven days. One patient dropped out from the study. 211 data sets were transmitted over a cumulative monitoring period of 140 days (overall adherence rate 82.2%). 55% and 8% of the transmitted ECG signals were sufficient for ventricular and atrial rhythm assessment, respectively. Although ECG signal quality has to be improved for better AF detection the developed communication design of joining Bluetooth and NFC technology in our telemonitoring system allows for ambulatory ECG acquisition with high adherence rates and system usability in heart failure patients.

Near Field Communication-based telemonitoring with integrated ECG recordings

PubMed Central

Morak, J.; Kumpusch, H.; Hayn, D.; Leitner, M.; Scherr, D.; Fruhwald, F.M.; Schreier, G.

2011-01-01

Objectives Telemonitoring of vital signs is an established option in treatment of patients with chronic heart failure (CHF). In order to allow for early detection of atrial fibrillation (AF) which is highly prevalent in the CHF population telemonitoring programs should include electrocardiogram (ECG) signals. It was therefore the aim to extend our current home monitoring system based on mobile phones and Near Field Communication technology (NFC) to enable patients acquiring their ECG signals autonomously in an easy-to-use way. Methods We prototypically developed a sensing device for the concurrent acquisition of blood pressure and ECG signals. The design of the device equipped with NFC technology and Bluetooth allowed for intuitive interaction with a mobile phone based patient terminal. This ECG monitoring system was evaluated in the course of a clinical pilot trial to assess the system’s technical feasibility, usability and patient’s adherence to twice daily usage. Results 21 patients (4f, 54 ± 14 years) suffering from CHF were included in the study and were asked to transmit two ECG recordings per day via the telemonitoring system autonomously over a monitoring period of seven days. One patient dropped out from the study. 211 data sets were transmitted over a cumulative monitoring period of 140 days (overall adherence rate 82.2%). 55% and 8% of the transmitted ECG signals were sufficient for ventricular and atrial rhythm assessment, respectively. Conclusions Although ECG signal quality has to be improved for better AF detection the developed communication design of joining Bluetooth and NFC technology in our telemonitoring system allows for ambulatory ECG acquisition with high adherence rates and system usability in heart failure patients. PMID:23616890

Challenges and Recent Developments in Hearing Aids: Part II. Feedback and Occlusion Effect Reduction Strategies, Laser Shell Manufacturing Processes, and Other Signal Processing Technologies

PubMed Central

Chung, King

2004-01-01

This is the second part of a review on the challenges and recent developments in hearing aids. Feedback and the occlusion effect pose great challenges in hearing aid design and usage. Yet, conventional solutions to feedback and the occlusion effect often create a dilemma: the solution to one often leads to the other. This review discusses the advanced signal processing strategies to reduce feedback and some new approaches to reduce the occlusion effect. Specifically, the causes of three types of feedback (acoustic, mechanical, and electromagnetic) are discussed. The strategies currently used to reduce acoustic feedback (i.e., adaptive feedback reduction algorithms using adaptive gain reduction, notch filtering, and phase cancellation strategies) and the design of new receivers that are built to reduce mechanical and electromagnetic feedback are explained. In addition, various new strategies (i.e., redesigned sound delivery devices and receiver-in-the-ear-canal hearing aid configuration) to reduce the occlusion effect are reviewed. Many manufacturers have recently adopted laser shell-manufacturing technologies to overcome problems associated with manufacturing custom hearing aid shells. The mechanisms of selected laser sintering and stereo lithographic apparatus and the properties of custom shells produced by these two processes are reviewed. Further, various new developments in hearing aid transducers, telecoils, channel-free amplification, open-platform programming options, rechargeable hearing aids, ear-level frequency modulated (FM) receivers, wireless Bluetooth FM systems, and wireless programming options are briefly explained and discussed. Finally, the applications of advanced hearing aid technologies to enhance other devices such as cochlear implants, hearing protectors, and cellular phones are discussed. PMID:15735871

Automobile inspection system based on wireless communication

NASA Astrophysics Data System (ADS)

Miao, Changyun; Ye, Chunqing

2010-07-01

This paper aims to research the Automobile Inspection System based on Wireless Communication, and suggests an overall design scheme which uses GPS for speed detection and Bluetooth and GPRS for communication. The communication between PDA and PC was realized by means of GPRS and TCP/IP; and the hardware circuit and software for detection terminal were devised by means of JINOU-3264 Bluetooth Module after analyzing the Bluetooth and its communication protocol. According to the results of debugging test, this system accomplished GPRS based data communication and management as well as the real-time detection on auto safety performance parameters in crash test via PC, whereby the need for mobility and reliability was met and the efficiency and level of detection was improved.

Mobile Sensor Technologies Being Developed

NASA Technical Reports Server (NTRS)

Greer, Lawrence C.; Oberle, Lawrence G.

2003-01-01

The NASA Glenn Research Center is developing small mobile platforms for sensor placement, as well as methods for communicating between roving platforms and a central command location. The first part of this project is to use commercially available equipment to miniaturize an existing sensor platform. We developed a five-circuit-board suite, with an average board size of 1.5 by 3 cm. Shown in the preceding photograph, this suite provides all motor control, direction finding, and communications capabilities for a 27- by 21- by 40-mm prototype mobile platform. The second part of the project is to provide communications between mobile platforms, and also between multiple platforms and a central command location. This is accomplished with a low-power network labeled "SPAN," Sensor Platform Area Network, a local area network made up of proximity elements. In practice, these proximity elements are composed of fixed- and mobile-sensor-laden science packages that communicate to each other via radiofrequency links. Data in the network will be shared by a central command location that will pass information into and out of the network through its access to a backbone element. The result will be a protocol portable to general purpose microcontrollers satisfying a host of sensor networking tasks. This network will enter the gap somewhere between television remotes and Bluetooth but, unlike 802.15.4, will not specify a physical layer, thus allowing for many data rates over optical, acoustical, radiofrequency, hardwire, or other media. Since the protocol will exist as portable C-code, developers may be able to embed it in a host of microcontrollers from commercial to space grade and, of course, to design it into ASICs. Unlike in 802.15.4, the nodes will relate to each other as peers. A demonstration of this protocol using the two test bed platforms was recently held. Two NASA modified, commercially available, mobile platforms communicated and shared data with each other and a

Technologically sensed social exposure related to slow-wave sleep in healthy adults.

PubMed

Butt, Maryam; Ouarda, Taha B M J; Quan, Stuart F; Pentland, Alex Sandy; Khayal, Inas

2015-03-01

The aim of this study is to understand the relationship between automatically captured social exposure and detailed sleep parameters of healthy young adults. This study was conducted in a real-world setting in a graduate-student housing community at a US university. Social exposure was measured using Bluetooth proximity sensing technology in mobile devices. Sleep was monitored in a naturalistic setting using a headband sleep monitoring device over a period of 2 weeks. The analysis included a total of 11 subjects (6 males and 5 females) aged 24-35 (149 subject nights). Slow-wave sleep showed a significant positive correlation (Spearman's rho = 0.51, p < 0.0001) with social exposure, whereas light non-REM (N1 + N2) sleep and wake time were found to be negatively correlated (rho = -0.25, p < 0.01; rho = -0.21, p < 0.01, respectively). The correlation of median slow-wave sleep with median social exposure per subject showed a strong positive significance (rho = 0.88, p < 0.001). On average, within subjects, following day's social exposure was higher when (slow-wave NREM + REM) percentage was high (Wilcoxon sign-ranked test, p < 0.05). Subjects with higher social exposure spent more time in slow-wave sleep. Following day's social exposure was found to be positively affected by previous night's (slow-wave NREM + REM) percentage. This suggests that sleep affects following day's social exposure and not vice versa. Capturing an individual's dynamic social behavior and sleep from their natural environment can provide novel insights into these relationships.

DLP NIRscan Nano: an ultra-mobile DLP-based near-infrared Bluetooth spectrometer

NASA Astrophysics Data System (ADS)

Gelabert, Pedro; Pruett, Eric; Perrella, Gavin; Subramanian, Sreeram; Lakshminarayanan, Aravind

2016-02-01

The DLP NIRscan Nano is an ultra-portable spectrometer evaluation module utilizing DLP technology to meet lower cost, smaller size, and higher performance than traditional architectures. The replacement of a linear array detector with DLP digital micromirror device (DMD) in conjunction with a single point detector adds the functionality of programmable spectral filters and sampling techniques that were not previously available on NIR spectrometers. This paper presents the hardware, software, and optical systems of the DLP NIRscan Nano and its design considerations on the implementation of a DLP-based spectrometer.

DreamTel; Diabetes risk evaluation and management tele-monitoring study protocol

PubMed Central

Tobe, Sheldon W; Wentworth, Joan; Ironstand, Laurie; Hartman, Susan; Hoppe, Jackie; Whiting, Judi; Kennedy, Janice; McAllister, Colin; Kiss, Alex; Perkins, Nancy; Vincent, Lloyd; Pylypchuk, George; Lewanczuk, Richard Z

2009-01-01

Background The rising prevalence of type 2 diabetes underlines the importance of secondary strategies for the prevention of target organ damage. While access to diabetes education centers and diabetes intensification management has been shown to improve blood glucose control, these services are not available to all that require them, particularly in rural and northern areas. The provision of these services through the Home Care team is an advance that can overcome these barriers. Transfer of blood glucose data electronically from the home to the health care provider may improve diabetes management. Methods and design The study population will consist of patients with type 2 diabetes with uncontrolled A1c levels living on reserve in the Battlefords region of Saskatchewan, Canada. This pilot study will take place over three phases. In the first phase over three months the impact of the introduction of the Bluetooth enabled glucose monitor will be assessed. In the second phase over three months, the development of guidelines based treatment algorithms for diabetes intensification will be completed. In the third phase lasting 18 months, study subjects will have diabetes intensification according to the algorithms developed. Discussion The first phase will determine if the use of the Bluetooth enabled blood glucose devices which can transmit results electronically will lead to changes in A1c levels. It will also determine the feasibility of recruiting subjects to use this technology. The rest of the Diabetes Risk Evaluation and Management Tele-monitoring (DreamTel) study will determine if the delivery of a diabetes intensification management program by the Home Care team supported by the Bluetooth enabled glucose meters leads to improvements in diabetes management. Trial Registration Protocol NCT00325624 PMID:19426530

Software-defined Radio Based Measurement Platform for Wireless Networks

PubMed Central

Chao, I-Chun; Lee, Kang B.; Candell, Richard; Proctor, Frederick; Shen, Chien-Chung; Lin, Shinn-Yan

2015-01-01

End-to-end latency is critical to many distributed applications and services that are based on computer networks. There has been a dramatic push to adopt wireless networking technologies and protocols (such as WiFi, ZigBee, WirelessHART, Bluetooth, ISA100.11a, etc.) into time-critical applications. Examples of such applications include industrial automation, telecommunications, power utility, and financial services. While performance measurement of wired networks has been extensively studied, measuring and quantifying the performance of wireless networks face new challenges and demand different approaches and techniques. In this paper, we describe the design of a measurement platform based on the technologies of software-defined radio (SDR) and IEEE 1588 Precision Time Protocol (PTP) for evaluating the performance of wireless networks. PMID:27891210

Software-defined Radio Based Measurement Platform for Wireless Networks.

PubMed

Chao, I-Chun; Lee, Kang B; Candell, Richard; Proctor, Frederick; Shen, Chien-Chung; Lin, Shinn-Yan

2015-10-01

End-to-end latency is critical to many distributed applications and services that are based on computer networks. There has been a dramatic push to adopt wireless networking technologies and protocols (such as WiFi, ZigBee, WirelessHART, Bluetooth, ISA100.11a, etc. ) into time-critical applications. Examples of such applications include industrial automation, telecommunications, power utility, and financial services. While performance measurement of wired networks has been extensively studied, measuring and quantifying the performance of wireless networks face new challenges and demand different approaches and techniques. In this paper, we describe the design of a measurement platform based on the technologies of software-defined radio (SDR) and IEEE 1588 Precision Time Protocol (PTP) for evaluating the performance of wireless networks.

Objective Method for Pain Detection/Diagnosis

DTIC Science & Technology

2013-11-01

implications. We developed a prototype of the Finger Sensor by combining a wireless pulse oximeter with the previously discussed Shimmer GSR sensor (Figure...NeuroSky and have executed a Developer Agreement. We elected to use a Bluetooth Finger Pulse Oximeter for recording blood oxygen saturation and... pulse . This pulse oximeter was chosen because it met all five of our selection criterion. The Bluetooth functionality makes it easy for us to

ST-Segment Analysis Using Wireless Technology in Acute Myocardial Infarction (STAT-MI) trial.

PubMed

Dhruva, Vivek N; Abdelhadi, Samir I; Anis, Ather; Gluckman, William; Hom, David; Dougan, William; Kaluski, Edo; Haider, Bunyad; Klapholz, Marc

2007-08-07

Our goal was to examine the effects of implementing a fully automated wireless network to reduce door-to-intervention times (D2I) in ST-segment elevation myocardial infarction (STEMI). Wireless technologies used to transmit prehospital electrocardiograms (ECGs) have helped to decrease D2I times but have unrealized potential. A fully automated wireless network that facilitates simultaneous 12-lead ECG transmission from emergency medical services (EMS) personnel in the field to the emergency department (ED) and offsite cardiologists via smartphones was developed. The system is composed of preconfigured Bluetooth devices, preprogrammed receiving/transmitting stations, dedicated e-mail servers, and smartphones. The network facilitates direct communication between offsite cardiologists and EMS personnel, allowing for patient triage directly to the cardiac catheterization laboratory from the field. Demographic, laboratory, and time interval data were prospectively collected and compared with calendar year 2005 data. From June to December 2006, 80 ECGs with suspected STEMI were transmitted via the network. Twenty patients with ECGs consistent with STEMI were triaged to the catheterization laboratory. Improvement was seen in mean door-to-cardiologist notification (-14.6 vs. 61.4 min, p < 0.001), door-to-arterial access (47.6 vs. 108.1 min, p < 0.001), time-to-first angiographic injection (52.8 vs. 119.2 min, p < 0.001), and D2I times (80.1 vs. 145.6 min, p < 0.001) compared with 2005 data. A fully automated wireless network that transmits ECGs simultaneously to the ED and offsite cardiologists for the early evaluation and triage of patients with suspected STEMI can decrease D2I times to <90 min and has the potential to be broadly applied in clinical practice.

Front end design of smartphone-based mobile health

NASA Astrophysics Data System (ADS)

Zhang, Changfan; He, Lingsong; Gao, Zhiqiang; Ling, Cong; Du, Jianhao

2015-02-01

Mobile health has been a new trend all over the world with the rapid development of intelligent terminals and mobile internet. It can help patients monitor health in-house and is convenient for doctors to diagnose remotely. Smart-phone-based mobile health has big advantages in cost and data sharing. Front end design of it mainly focuses on two points: one is implementation of medical sensors aimed at measuring kinds of medical signal; another is acquisition of medical signal from sensors to smart phone. In this paper, the above two aspects were both discussed. First, medical sensor implementation was proposed to refer to mature measurement solutions with ECG (electrocardiograph) sensor design taken for example. And integrated chip using can simplify design. Then second, typical data acquisition architecture of smart phones, namely Bluetooth and MIC (microphone)-based architecture, were compared. Bluetooth architecture should be equipped with an acquisition card; MIC design uses sound card of smart phone instead. Smartphone-based virtual instrument app design corresponding to above acquisition architecture was discussed. In experiments, Bluetooth and MIC architecture were used to acquire blood pressure and ECG data respectively. The results showed that Bluetooth design can guarantee high accuracy during the acquisition and transmission process, and MIC design is competitive because of low cost and convenience.

Surgical Vision: Google Glass and Surgery.

PubMed

Chang, Johnny Yau Cheung; Tsui, Lok Yee; Yeung, Keith Siu Kay; Yip, Stefanie Wai Ying; Leung, Gilberto Ka Kit

2016-08-01

Google Glass is, in essence, a smartphone in the form of a pair of spectacles. It has a display system, a bone conduction "speaker," video camera, and connectivity via WiFi or Bluetooth technologies. It can also be controlled by voice command. Seizing Google Glass' capabilities as windows of opportunity, surgeons have been the first group of doctors trying to incorporate the technology into their daily practices. Experiences from different groups have demonstrated Google Glass' potential in improving perioperative care, intraoperative communication and documentation, surgical outcome as well as surgical training. On the other hand, the device has technical limitations, notably suboptimal image qualities and a short battery life. Its operational functions also bring forth concerns on the protection of patient privacy. Nonetheless, the technological advances that this device embodies hold promises in surgical innovations. Further studies are required, and surgeons should explore, investigate, and embrace similar technologies with keen and informed anticipation. © The Author(s) 2016.

Development of a Portable Two-Way Communication and Information Device for Deafblind People.

PubMed

Ozioko, Oliver; Hersh, Marion

2015-01-01

This paper presents research on the development of a wearable two-way communication and information device for deafblind people who use tactile communications methods, namely the British deafblind manual alphabet and/or Braille. The device has two components: a glove worn by the deafblind person and a handheld display with keypad to be used by their hearing and sighted communication partner. Users can send messages using pressure sensors embedded in the glove and receive them by means of vibration on the palm. The two components are linked by Bluetooth and the use of Bluetooth to communicate with computers, mobile phones and other Bluetooth enabled devices is being investigated. The design was informed by feedback obtained from a survey of deafblind people and interviews with staff in two organisations for deafblind people. Research and development of the device is still ongoing.

Aorta: a management layer for mobile peer-to-peer massive multiplayer games

NASA Astrophysics Data System (ADS)

Edlich, Stefan; Hoerning, Henrik; Brunnert, Andreas; Hoerning, Reidar

2005-03-01

The development of massive multiplayer games (MMPGs) for personal computers is based on a wide range of frameworks and technologies. In contrast, MMPG development for cell phones lacks the availability of framework support. We present Aorta as a multi-purpose lightweight MIDP 2.0 framework to support the transparent and equal API usage of peer-to-peer communication via http, IP and Bluetooth. Special experiments, such as load-tests on Nokia 6600s, have been carried out with Bluetooth support in using a server-as-client architecture to create ad-hoc networks by using piconet functionalities. Additionally, scatternet functionalities, which will be supported in upcoming devices, have been tested in a simulated environment on more than 12 cell phones. The core of the Aorta framework is the Etherlobby, which manages connections, peers, the game lobby, game policies and much more. The framework itself was developed to enable the fast development of mobile games, regardless of the distance between users, which might be within the schoolyard or much further away. The earliest market-ready application shown here is a multimedia game for cell phones utilizing all of the frameworks features. This game, called Micromonster, acts as platform for developer tests, as well as providing valuable information about interface usability and user acceptance.

Noise-Robust Monitoring of Lombard Speech Using a Wireless Neck-surface Accelerometer and Microphone

DTIC Science & Technology

2017-08-20

rechargeable, lithium - ion polymer battery that can be charged through a micro-USB input on the circuit. The micro-USB input also allows for communication to...protection, an on/off switch for the battery , status LEDs, and a logic switch that enables the `Bluetooth module to be fully functional when...simultaneously powered via USB and battery . The system contains a small receiver that is equipped with the same Bluetooth module as the transmitter (BC127

Gas detection with microelectromechanical Fabry-Perot interferometer technology in cell phone

NASA Astrophysics Data System (ADS)

Mannila, Rami; Hyypiö, Risto; Korkalainen, Marko; Blomberg, Martti; Kattelus, Hannu; Rissanen, Anna

2015-06-01

VTT Technical Research Centre of Finland has developed a miniaturized optical sensor for gas detection in a cell phone. The sensor is based on a microelectromechanical (MEMS) Fabry-Perot interferometer, which is a structure with two highly reflective surfaces separated by a tunable air gap. The MEMS FPI is a monolithic device, i.e. it is made entirely on one substrate in a batch process, without assembling separate pieces together. The gap is adjusted by moving the upper mirror with electrostatic force, so there are no actual moving parts. VTT has designed and manufactured a MEMS FPI based carbon dioxide sensor demonstrator which is integrated to a cell phone shield cover. The demonstrator contains light source, gas cell, MEMS FPI, detector, control electronics and two coin cell batteries as a power source. It is connected to the cell phone by Bluetooth. By adjusting the wavelength range and customizing the MEMS FPI structure, it is possible to selectively sense multiple gases.

Introductory Physics Experiments Using the Wiimote

NASA Astrophysics Data System (ADS)

Somers, William; Rooney, Frank; Ochoa, Romulo

2009-03-01

The Wii, a video game console, is a very popular device with millions of units sold worldwide over the past two years. Although computationally it is not a powerful machine, to a physics educator its most important components can be its controllers. The Wiimote (or remote) controller contains three accelerometers, an infrared detector, and Bluetooth connectivity at a relatively low price. Thanks to available open source code, any PC with Bluetooth capability can detect the information sent out by the Wiimote. We have designed several experiments for introductory physics courses that make use of the accelerometers and Bluetooth connectivity. We have adapted the Wiimote to measure the: variable acceleration in simple harmonic motion, centripetal and tangential accelerations in circular motion, and the accelerations generated when students lift weights. We present the results of our experiments and compare them with those obtained when using motion and/or force sensors.

Assessing the use of BreatheSmart® mobile technology in adult patients with asthma: a remote observational study.

PubMed

Melvin, Emilie; Cushing, Anna; Tam, Anne; Kitada, Ruri; Manice, Melissa

2017-01-01

Non-adherence to asthma daily controller medications is a common problem, reported to be responsible for 60% of asthma-related hospitalisations. The mean level of adherence for asthma medications is estimated to be as low as 22%. Therefore, objective measurements of adherence to medicine are necessary. This virtual observational study is designed to measure the usability of an electronic monitoring device platform that measures adherence. Understanding how patients use the BreatheSmart mobile technology at home is essential to assess its feasibility as a solution to improve medication adherence. We anticipate this approach can be applied to real-world environments as a cost-effective solution to improve medication adherence. This is a virtual 6-month observational study of 100 adults (≥18 years) with an asthma diagnosis, using inhaled corticosteroids for at least 3 months. Participants will be recruited in the USA through ad placements online. All participants receive wireless Bluetooth-enabled inhaler sensors that track medication usage and an mSpirometer TM capable of clinical-grade lung function measurements, and download the BreatheSmart mobile application that transmits data to a secure server. All analyses are based on an intention-to-treat. Usability is assessed by patient questionnaires and question sessions. Simple paired t-test is used to assess significant change in Asthma Control Test score, quality of life (EuroQol-5D questionnaire) and lung function. No ethical or safety concerns pertain to the collection of these data. Results of this research are planned to be published as soon as available. NCT03103880.

Development of a low cost, GPS-based upgrade to a standard handheld gamma detector for mapping environmental radioactive contamination.

PubMed

Paridaens, J

2006-02-01

A low cost extension to a standard handheld radiation monitor was developed, allowing one to perform outdoor georeferenced gamma measurements. It consists of a commercial wireless Bluetooth GPS receiver, a commercial RS-232 to Bluetooth converter combined with a standard Bluetooth enabled pocket personal computer (PPC). The system is intended for use in difficult to access areas, typically for foot campaigns. As the operator walks, a straightforward homemade visual basic program alternately reads GPS position and gamma dose rate into the PPC, creating a data log. This allows a single operator on foot to map between 50 and 200 ha of environmental radiation per day in very rugged areas, depending on the accessibility of the terrain and the detail required. On a test field with known contamination, a spatial precision of about 5-10 m was obtainable. The device was also used to reveal complex contamination patterns in the flooding zones of a radioactively contaminated small river.

Real-time long term measurement using integrated framework for ubiquitous smart monitoring

NASA Astrophysics Data System (ADS)

Heo, Gwanghee; Lee, Giu; Lee, Woosang; Jeon, Joonryong; Kim, Pil-Joong

2007-04-01

Ubiquitous monitoring combining internet technologies and wireless communication is one of the most promising technologies of infrastructure health monitoring against the natural of man-made hazards. In this paper, an integrated framework of the ubiquitous monitoring is developed for real-time long term measurement in internet environment. This framework develops a wireless sensor system based on Bluetooth technology and sends measured acceleration data to the host computer through TCP/IP protocol. And it is also designed to respond to the request of web user on real time basis. In order to verify this system, real time monitoring tests are carried out on a prototype self-anchored suspension bridge. Also, wireless measurement system is analyzed to estimate its sensing capacity and evaluate its performance for monitoring purpose. Based on the evaluation, this paper proposes the effective strategies for integrated framework in order to detect structural deficiencies and to design an early warning system.

Adaptive User Profiles in Pervasive Advertising Environments

NASA Astrophysics Data System (ADS)

Alt, Florian; Balz, Moritz; Kristes, Stefanie; Shirazi, Alireza Sahami; Mennenöh, Julian; Schmidt, Albrecht; Schröder, Hendrik; Goedicke, Michael

Nowadays modern advertising environments try to provide more efficient ads by targeting costumers based on their interests. Various approaches exist today as to how information about the users' interests can be gathered. Users can deliberately and explicitly provide this information or user's shopping behaviors can be analyzed implicitly. We implemented an advertising platform to simulate an advertising environment and present adaptive profiles, which let users setup profiles based on a self-assessment, and enhance those profiles with information about their real shopping behavior as well as about their activity intensity. Additionally, we explain how pervasive technologies such as Bluetooth can be used to create a profile anonymously and unobtrusively.

Support and rehabilitation of patients with pulmonary expansion deficit by using game therapy.

PubMed

Chacon, P F S; Schon, C F; Furtado, V H L A; Signoretti, G L A M; Oliveira, J P P; Ribeiro, A G; Wanderley, C D V; Diniz, A A R; Soares, H B

2016-08-01

Patients suffering from hypoventilation and pulmonary expansion deficit are at increased risk of developing pulmonary complications such as atelectasis, pneumonia or pleural effusion. These complications can increase the length of stay and spending on health, and generate long-term functional impairment. This study aims to produce a therapeutic alternative to the traditional method of lung re-expansion through incentive spirometry (IS) using the game therapy to build an innovative system. This system makes use of infrared and Bluetooth communication technology to associate the game therapy to EI. At the end of the system implementation, we expect to obtain good adhesion of the patient and the physiotherapists.

A short-range optical wireless transmission method based on LED

NASA Astrophysics Data System (ADS)

Miao, Meiyuan; Chen, Ailin; Zhu, Mingxing; Li, Ping; Gao, Yingming; Zou, Nianyu

2016-10-01

As to electromagnetic wave interfere and only one to one transmission problem of Bluetooth, a short-range LED optical wireless transmission method is proposed to be complementary technology in this paper. Furthermore achieved image transmission through this method. The system makes C52 to be the mater controller, transmitter got data from terminals by USB and sends modulated signals with LED. Optical signal is detected by PD, through amplified, filtered with shaping wave from, and demodulated on receiver. Then send to terminals like PC and reverted back to original image. Analysis the performance from peak power and average power, power consumption of transmitter, relationship of bit error rate and modulation mode, and influence of ambient light, respectively. The results shows that image can be received accurately which uses this method. The most distant transmission distance can get to 1m with transmitter LED source of 1w, and the transfer rate is 14.4Kbit/s with OOK modulation mode on stabilization system, the ambient light effect little to LED transmission system in normal light environment. The method is a convenient to carry LED wireless short range transmission for mobile transmission equipment as a supplement of Bluetooth short-range transmission for its ISM band interfere, and the analysis method in this paper can be a reference for other similar systems. It also proves the system is feasibility for next study.

A low-cost miniaturised detector for environmental radioactivity measurements

NASA Astrophysics Data System (ADS)

Aplin, Karen; Briggs, Aaron; Hastings, Peter; Harrison, R. Giles; Marlton, Graeme; Baird, Adam

2017-04-01

We have developed a low-cost (£ few hundred), low-power (40mA), low-mass (30g) detector for environmental radioactivity measurements, using scintillator and solid state technology. The detector can measure energy and therefore has the capability to distinguish between different types of energetic particle. Results from recent tests, when our detector was integrated with a meteorological radiosonde system, and flew on a balloon up to 25km, identified the transition region between energetic particles near the surface, dominated by terrestrial gamma emissions, and higher-energy particles in the free troposphere from cosmic rays. The detector can be used with Bluetooth technology for remote monitoring, which is particularly useful for hazardous areas. It is also small and cheap enough to be used in sensor networks for a wide range of applications, from atmospheric science to disaster monitoring.

Smartphone app design for the wireless control of a neuromuscular electrical stimulator device with integrated randomization allocation process for RCT applications.

PubMed

Sweeney, Dean; Quinlan, Leo R; OLaighin, Gearoid

2015-08-01

The use of NMES has evolved over the last five decades. Technological advancements have transformed these once complex systems into user-friendly devices with enhanced control functions, leading to new applications of NMES being investigated. The use of Randomized Control Trial (RCT) methodology in evaluating the effectiveness of new and existing applications of NMES is a demanding process adding time and cost to a translation into clinical practice. Poor quality trials may result in poor evidence of NMES effectiveness. In this paper some of the key challenges encountered in NMES clinical trials are identified with the aim of purposing a solution to address these challenges through the adoption of Smartphone technology. The design and evaluation of a smartphone application to provide automatic blind randomization control and facilitating the wireless temporal control of a portable Bluetooth enabled NMES is presented.

Wireless communication in health care: who will win the right to send data boldly where no data has gone before?

PubMed

Campbell, Robert J; Durigon, Louis

2003-01-01

Increasingly, health care professionals will need to retrieve, store, share, and send data using several types of wireless devices. These devices include personal digital assistants, laptops, Web tablets, cell phones, and clothing that monitor heart rate and blood pressure. Regardless of the device, several standards will vie for the right to provide the wireless communications link between the health care professional and the wired data resources located within a health care organization. This article identifies the top three technologies in the wireless communications field: Wireless Fidelity (WiFi), Mobile Communications, and Bluetooth; breaks down each according to its strengths and weaknesses; and makes recommendations for their use by health care professionals located inside and outside a health care facility. Where appropriate the discussion includes an explication of how a specific technology can be made secure from hackers and other security breeches.

A home automation based environmental sound alert for people experiencing hearing loss.

PubMed

Mielke, Matthias; Bruck, Rainer

2016-08-01

Different assistive technologies are available for deaf people (i.e. deaf, deafened, and hard of hearing). Besides the well-known hearing aid, devices for detection of sound events that occur at home or at work (e.g. doorbell, telephone) are available. Despite the technological progress in the last years and resulting new possibilities, the basic functions and concepts of such devices have not changed. The user still needs special assistive technology that is bound to the home or work environment. In this contribution a new concept for awareness of events in buildings is presented. In contrast to state-of-the-art assistive devices, it makes use of modern Information and Communication and home automation technology, and thus offers the prospect of cheap implementation and higher comfort for the user. In this concept events are indicated by notifications that are send over a Bluetooth Low Energy mesh network from a source to the user. The notifications are received by the user's smartwatch and the event is indicated by vibration and an icon representing its source.

Architecture of a Service-Enabled Sensing Platform for the Environment

PubMed Central

Kotsev, Alexander; Pantisano, Francesco; Schade, Sven; Jirka, Simon

2015-01-01

Recent technological advancements have led to the production of arrays of miniaturized sensors, often embedded in existing multitasking devices (e.g., smartphones, tablets) and using a wide range of radio standards (e.g., Bluetooth, Wi-Fi, 4G cellular networks). Altogether, these technological evolutions coupled with the diffusion of ubiquitous Internet connectivity provide the base-line technology for the Internet of Things (IoT). The rapid increase of IoT devices is enabling the definition of new paradigms of data collection and introduces the concept of mobile crowd-sensing. In this respect, new sensing methodologies promise to extend the current understanding of the environment and social behaviors by leveraging citizen-contributed data for a wide range of applications. Environmental sensing can however only be successful if all the heterogeneous technologies and infrastructures work smoothly together. As a result, the interconnection and orchestration of devices is one of the central issues of the IoT paradigm. With this in mind, we propose an approach for improving the accessibility of observation data, based on interoperable standards and on-device web services. PMID:25688593

Architecture of a service-enabled sensing platform for the environment.

PubMed

Kotsev, Alexander; Pantisano, Francesco; Schade, Sven; Jirka, Simon

2015-02-13

Recent technological advancements have led to the production of arrays of miniaturized sensors, often embedded in existing multitasking devices (e.g., smartphones, tablets) and using a wide range of radio standards (e.g., Bluetooth, Wi-Fi, 4G cellular networks). Altogether, these technological evolutions coupled with the diffusion of ubiquitous Internet connectivity provide the base-line technology for the Internet of Things (IoT). The rapid increase of IoT devices is enabling the definition of new paradigms of data collection and introduces the concept of mobile crowd-sensing. In this respect, new sensing methodologies promise to extend the current understanding of the environment and social behaviors by leveraging citizen-contributed data for a wide range of applications. Environmental sensing can however only be successful if all the heterogeneous technologies and infrastructures work smoothly together. As a result, the interconnection and orchestration of devices is one of the central issues of the IoT paradigm. With this in mind, we propose an approach for improving the accessibility of observation data, based on interoperable standards and on-device web services.

Wireless medical sensor networks: design requirements and enabling technologies.

PubMed

Vallejos de Schatz, Cecilia H; Medeiros, Henry Ponti; Schneider, Fabio K; Abatti, Paulo J

2012-06-01

This article analyzes wireless communication protocols that could be used in healthcare environments (e.g., hospitals and small clinics) to transfer real-time medical information obtained from noninvasive sensors. For this purpose the features of the three currently most widely used protocols-namely, Bluetooth(®) (IEEE 802.15.1), ZigBee (IEEE 802.15.4), and Wi-Fi (IEEE 802.11)-are evaluated and compared. The important features under consideration include data bandwidth, frequency band, maximum transmission distance, encryption and authentication methods, power consumption, and current applications. In addition, an overview of network requirements with respect to medical sensor features, patient safety and patient data privacy, quality of service, and interoperability between other sensors is briefly presented. Sensor power consumption is also discussed because it is considered one of the main obstacles for wider adoption of wireless networks in medical applications. The outcome of this assessment will be a useful tool in the hands of biomedical engineering researchers. It will provide parameters to select the most effective combination of protocols to implement a specific wireless network of noninvasive medical sensors to monitor patients remotely in the hospital or at home.

Building a Dynamic Spectrum Access Smart Radio with Application to Public Safety Disaster Communications

DTIC Science & Technology

2009-08-13

User Interface Master C ontroller (MC ) C ompos ite XML C onfiguration & E vents Awareness Universal  R adio F ramework US R P 802.11 B luetooth E...Bluetooth Database US R P  Database Adapters to be evaluated in Network Testbed Memory Adaptability Policy C ontrol Interoperability Figure 4.2...10 15 20 25 30 10-3 10-2 10-1 100 101 102 103 time (sec) UDP Jitter Ji tte r ( m s) 802.3 Wired 802.11 Wireless Bluetooth GNU Radio/USRP Figure

Study protocol: mobile improvement of self-management ability through rural technology (mI SMART).

PubMed

Mallow, Jennifer A; Theeke, Laurie A; Long, Dustin M; Whetsel, Tara; Theeke, Elliott; Mallow, Brian K

2015-01-01

There are 62 million Americans currently residing in rural areas who are more likely to have multiple chronic conditions and be economically disadvantaged, and in poor health, receive less recommended preventive services and attend fewer visits to health care providers. Recent advances in mobile healthcare (mHealth) offer a promising new approach to solving health disparities and improving chronic illness care. It is now possible and affordable to transmit health information, including values from glucometers, automated blood pressure monitors, and scales, through Bluetooth-enabled devices. Additionally, audio and video communications technologies can allow healthcare providers to conduct many parts of a physical exam remotely from varied settings. These technologies could remove geographical distance as a barrier to care and diminish the access to care issues faced by patients who live rurally. However, currently there is lack of studies that provide evidence of feasibility, acceptability, and effectiveness of mHealth initiatives on improved outcomes of care, a needed step to make the translation to implementation studies in healthcare systems. The purpose of this paper is to present the protocol for the first study of mI SMART (mobile Improvement of Self-Management Ability through Rural Technology), a new integrated mHealth intervention. Our objective is to provide evidence of feasibility and acceptability for the use of mI SMART in an underserved population and establish evidence for the refinement of mI SMART. The proposed study will take place at Milan Puskar Health Right, a free primary care clinic in the state of West Virginia. The clinic provides health care at no cost to uninsured, low income; adults aged 18-64 living in West Virginia. We will enroll 30 participants into this feasibility study with plans of implementing a longitudinal randomized, comparative effectiveness design in the future. Data collection will include tracking of barriers and

A novel pen-based Bluetooth-enabled insulin delivery system with insulin dose tracking and advice.

PubMed

Bailey, Timothy S; Stone, Jenine Y

2017-05-01

Diabetes is growing in prevalence internationally. As more individuals require insulin as part of their treatment, technology evolves to optimize delivery, improve adherence, and reduce dosing errors. Insulin pens outperform vial and syringe in simplicity, dosing accuracy, and user preference. Bolus advisors improve dosing confidence and treatment adherence. The InPen System offers a novel approach to treatment via a wireless pen that syncs to a mobile application featuring a bolus advisor, enabling convenient insulin dose tracking and more accurate bolus advice among other features. Areas covered: Existing technology for insulin delivery and bolus advice are reviewed. The mechanics and functionality of the InPen device are delineated. Findings from formative testing and usability studies of the InPen system are reported. Future directions for the InPen system in the treatment of diabetes are discussed. Expert opinion: Diabetes management is complex and largely data-driven. The InPen System offers a promising new opportunity to avail insulin pen-users of features known to improve treatment efficacy, which have otherwise primarily been available to those using pumps. Given that the majority of insulin users do not use insulin pumps, the InPen System is poised to improve glucose control in a significant portion of the diabetes population.

The development of remote wireless radiation dose monitoring system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Jin-woo; Chonbuk National University, Jeonjoo-Si; Jeong, Kyu-hwan

Internet of things (IoT) technology has recently shown a large flow of IT trends in human life. In particular, our lives are now becoming integrated with a lot of items around the 'smart-phone' with IoT, including Bluetooth, Near Field Communication (NFC), Beacons, WiFi, and Global Positioning System (GPS). Our project focuses on the interconnection of radiation dosimetry and IoT technology. The radiation workers at a nuclear facility should hold personal dosimeters such as a Thermo-Luminescence Dosimeter (TLD), an Optically Stimulated Luminescence Dosimeter (OSL), pocket ionization chamber dosimeters, an Electronic Personal Dosimeter (EPD), or an alarm dosimeter on their body. Somemore » of them have functions that generate audible or visible alarms to radiation workers in a real working area. However, such devices used in radiation fields these days have no functions for communicating with other areas or the responsible personnel in real time. In particular, when conducting a particular task in a high dose area, or a number of repair works within a radiation field, radiation dose monitoring is important for the health of the workers and the work efficiency. Our project aims at the development of a remote wireless radiation dose monitoring system (RWRD) that can be used to monitor the radiation dose in a nuclear facility for radiation workers and a radiation protection program In this project, a radiation dosimeter is the detection device for personal radiation dose, a smart phone is the mobile wireless communication tool, and, Beacon is the wireless starter for the detection, communication, and position of the worker using BLE (Bluetooth Low Energy). In this report, we report the design of the RWRD and a demonstration case in a real radiation field. (authors)« less

Remotely controlling of mobile robots using gesture captured by the Kinect and recognized by machine learning method

NASA Astrophysics Data System (ADS)

Hsu, Roy CHaoming; Jian, Jhih-Wei; Lin, Chih-Chuan; Lai, Chien-Hung; Liu, Cheng-Ting

2013-01-01

The main purpose of this paper is to use machine learning method and Kinect and its body sensation technology to design a simple, convenient, yet effective robot remote control system. In this study, a Kinect sensor is used to capture the human body skeleton with depth information, and a gesture training and identification method is designed using the back propagation neural network to remotely command a mobile robot for certain actions via the Bluetooth. The experimental results show that the designed mobile robots remote control system can achieve, on an average, more than 96% of accurate identification of 7 types of gestures and can effectively control a real e-puck robot for the designed commands.

Design and evaluation of a telemonitoring concept based on NFC-enabled mobile phones and sensor devices.

PubMed

Morak, Jürgen; Kumpusch, Hannes; Hayn, Dieter; Modre-Osprian, Robert; Schreier, Günter

2012-01-01

Utilization of information and communication technologies such as mobile phones and wireless sensor networks becomes more and more common in the field of telemonitoring for chronic diseases. Providing elderly people with a mobile-phone-based patient terminal requires a barrier-free design of the overall user interface including the setup of wireless communication links to sensor devices. To easily manage the connection between a mobile phone and wireless sensor devices, a concept based on the combination of Bluetooth and near-field communication technology has been developed. It allows us initiating communication between two devices just by bringing them close together for a few seconds without manually configuring the communication link. This concept has been piloted with a sensor device and evaluated in terms of usability and feasibility. Results indicate that this solution has the potential to simplify the handling of wireless sensor networks for people with limited technical skills.

An IBeacon-Based Location System for Smart Home Control.

PubMed

Liu, Qinghe; Yang, Xinshuang; Deng, Lizhen

2018-06-11

Indoor location and intelligent control system can bring convenience to people’s daily life. In this paper, an indoor control system is designed to achieve equipment remote control by using low-energy Bluetooth (BLE) beacon and Internet of Things (IoT) technology. The proposed system consists of five parts: web server, home gateway, smart terminal, smartphone app and BLE beacons. In the web server, fingerprint matching based on RSSI stochastic characteristic and posture recognition model based on geomagnetic sensing are used to establish a more efficient equipment control system, combined with Pedestrian Dead Reckoning (PDR) technology to improve the accuracy of location. A personalized menu of remote “one-click” control is finally offered to users in a smartphone app. This smart home control system has been implemented by hardware, and precision and stability tests have been conducted, which proved the practicability and good user experience of this solution.

WebTag: Web browsing into sensor tags over NFC.

PubMed

Echevarria, Juan Jose; Ruiz-de-Garibay, Jonathan; Legarda, Jon; Alvarez, Maite; Ayerbe, Ana; Vazquez, Juan Ignacio

2012-01-01

Information and Communication Technologies (ICTs) continue to overcome many of the challenges related to wireless sensor monitoring, such as for example the design of smarter embedded processors, the improvement of the network architectures, the development of efficient communication protocols or the maximization of the life cycle autonomy. This work tries to improve the communication link of the data transmission in wireless sensor monitoring. The upstream communication link is usually based on standard IP technologies, but the downstream side is always masked with the proprietary protocols used for the wireless link (like ZigBee, Bluetooth, RFID, etc.). This work presents a novel solution (WebTag) for a direct IP based access to a sensor tag over the Near Field Communication (NFC) technology for secure applications. WebTag allows a direct web access to the sensor tag by means of a standard web browser, it reads the sensor data, configures the sampling rate and implements IP based security policies. It is, definitely, a new step towards the evolution of the Internet of Things paradigm.

WebTag: Web Browsing into Sensor Tags over NFC

PubMed Central

Echevarria, Juan Jose; Ruiz-de-Garibay, Jonathan; Legarda, Jon; Álvarez, Maite; Ayerbe, Ana; Vazquez, Juan Ignacio

2012-01-01

Information and Communication Technologies (ICTs) continue to overcome many of the challenges related to wireless sensor monitoring, such as for example the design of smarter embedded processors, the improvement of the network architectures, the development of efficient communication protocols or the maximization of the life cycle autonomy. This work tries to improve the communication link of the data transmission in wireless sensor monitoring. The upstream communication link is usually based on standard IP technologies, but the downstream side is always masked with the proprietary protocols used for the wireless link (like ZigBee, Bluetooth, RFID, etc.). This work presents a novel solution (WebTag) for a direct IP based access to a sensor tag over the Near Field Communication (NFC) technology for secure applications. WebTag allows a direct web access to the sensor tag by means of a standard web browser, it reads the sensor data, configures the sampling rate and implements IP based security policies. It is, definitely, a new step towards the evolution of the Internet of Things paradigm. PMID:23012511

A Wireless Sensor Network for Urban Traffic Characterization and Trend Monitoring

PubMed Central

Fernández-Lozano, J.J.; Martín-Guzmán, Miguel; Martín-Ávila, Juan; García-Cerezo, A.

2015-01-01

Sustainable mobility requires a better management of the available infrastructure resources. To achieve this goal, it is necessary to obtain accurate data about road usage, in particular in urban areas. Although a variety of sensor alternates for urban traffic exist, they usually require extensive investments in the form of construction works for installation, processing means, etc. Wireless Sensor Networks (WSN) are an alternative to acquire urban traffic data, allowing for flexible, easy deployment. Together with the use of the appropriate sensors, like Bluetooth identification, and associate processing, WSN can provide the means to obtain in real time data like the origin-destination matrix, a key tool for trend monitoring which previously required weeks or months to be completed. This paper presents a system based on WSN designed to characterize urban traffic, particularly traffic trend monitoring through the calculation of the origin-destination matrix in real time by using Bluetooth identification. Additional sensors are also available integrated in different types of nodes. Experiments in real conditions have been performed, both for separate sensors (Bluetooth, ultrasound and laser), and for the whole system, showing the feasibility of this approach. PMID:26501278

A semi-implantable multichannel telemetry system for continuous electrical, mechanical and hemodynamical recordings in animal cardiac research.

PubMed

Kong, Wei; Huang, Jian; Rollins, Dennis L; Ideker, Raymond E; Smith, William M

2007-03-01

We have developed an eight-channel telemetry system for studying experimental models of chronic cardiovascular disease. The system is an extension of a previous device that has been miniaturized, reduced in power consumption and provided with increased functionality. We added sensors for ventricular dimension, and coronary artery blood flow and arterial blood pressure that are suitable for use with the system. The telemetry system consists of a front end, a backpack and a host PC. The front end is a watertight stainless steel case with all sensor electronics sealed inside; it acquires dimension, flow, pressure and five cardiac electrograms from selected locations on the heart. The backpack includes a control unit, Bluetooth radio, and batteries. The control unit digitizes eight channels of data from the front end and forwards them to the host PC via Bluetooth link. The host PC has a receiving Bluetooth radio and Labview programs to store and display data. The whole system was successfully tested on the bench and in an animal model. This telemetry system will greatly enhance the ability to study events leading to spontaneous sudden cardiac arrest.

A wireless sensor network for urban traffic characterization and trend monitoring.

PubMed

Fernández-Lozano, J J; Martín-Guzmán, Miguel; Martín-Ávila, Juan; García-Cerezo, A

2015-10-15

Sustainable mobility requires a better management of the available infrastructure resources. To achieve this goal, it is necessary to obtain accurate data about road usage, in particular in urban areas. Although a variety of sensor alternates for urban traffic exist, they usually require extensive investments in the form of construction works for installation, processing means, etc. Wireless Sensor Networks (WSN) are an alternative to acquire urban traffic data, allowing for flexible, easy deployment. Together with the use of the appropriate sensors, like Bluetooth identification, and associate processing, WSN can provide the means to obtain in real time data like the origin-destination matrix, a key tool for trend monitoring which previously required weeks or months to be completed. This paper presents a system based on WSN designed to characterize urban traffic, particularly traffic trend monitoring through the calculation of the origin-destination matrix in real time by using Bluetooth identification. Additional sensors are also available integrated in different types of nodes. Experiments in real conditions have been performed, both for separate sensors (Bluetooth, ultrasound and laser), and for the whole system, showing the feasibility of this approach.

Wireless patient monitoring system for a moving-actuator type artificial heart.

PubMed

Nam, K W; Chung, J; Choi, S W; Sun, K; Min, B G

2006-10-01

In this study, we developed a wireless monitoring system for outpatients equipped with a moving-actuator type pulsatile bi-ventricular assist device, AnyHeart. The developed monitoring system consists of two parts; a Bluetooth-based short-distance self-monitoring system that can monitor and control the operating status of a VAD using a Bluetooth-embedded personal digital assistant or a personal computer within a distance of 10 meters, and a cellular network-based remote monitoring system that can continuously monitor and control the operating status of AnyHeart at any location. Results of in vitro experiments demonstrate the developed system's ability to monitor the operational status of an implanted AnyHeart.

ARPA-E Program: Advanced Management Protection of Energy Storage Devices (AMPED) - Fifth Quarterly Project Report - FY14 Q1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Joseph

Technology has been developed that enables monitoring of individual cells in high - capacity lithium-ion battery packs, with a distributed array of wireless Bluetooth 4.0 tags and sensors, and without proliferation of extensive wiring harnesses. Given the safety challenges facing lithium-ion batteries in electric vehicle, civilian aviation and defense applications, these wireless sensors may be particularly important to these emerging markets. These wireless sensors will enhance the performance, reliability and safety of such energy storage systems. Specific accomplishments to date include, but are not limited to: (1) the development of wireless tags using Bluetooth 4.0 standard to monitor a largemore » array of sensors in battery pack; (2) sensor suites enabling the simultaneous monitoring of cell voltage, cell current, cell temperature, and package strain, indicative of swelling and increased internal pressure, (3) small receivers compatible with USB ports on portable computers; (4) software drivers and logging software; (5) a 7S2P battery simulator, enabling the safe development of wireless BMS hardware in the laboratory; (6) demonstrated data transmission out of metal enclosures, including battery box, with small variable aperture opening; (7) test data demonstrating the accurate and reliable operation of sensors, with transmission of terminal voltage, cell temperature and package strain at distances up to 110 feet; (8) quantification of the data transmission error as a function of distance, in both indoor and outdoor operation; (9) electromagnetic interference testing during operation with live, high -capacity battery management system at Yardney Technical Products; (10) demonstrat ed operation with live high-capacity lithium-ion battery pack during charge-discharge cycling; (11) development of special polymer-gel lithium-ion batteries with embedded temperature sensors, capable of measuring the core temperature of individual of the cells during charge

Novel Battery Management System with Distributed Wireless and Fiber Optic Sensors for Early Detection and Suppression of Thermal Runaway in Large Battery Packs, FY13 Q4 Report, ARPA-E Program: Advanced Management Protection of Energy Storage Devices (AMPE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, J.; Chang, J.; Zumstein, J.

Technology has been developed that enables monitoring of individual cells in highcapacity lithium-ion battery packs, with a distributed array of wireless Bluetooth 4.0 tags and sensors, and without proliferation of extensive wiring harnesses. Given the safety challenges facing lithium-ion batteries in electric vehicle, civilian aviation and defense applications, these wireless sensors may be particularly important to these emerging markets. These wireless sensors will enhance the performance, reliability and safety of such energy storage systems. Specific accomplishments to date include, but are not limited to: (1) the development of wireless tags using Bluetooth 4.0 standard to monitor a large array ofmore » sensors in battery pack; (2) sensor suites enabling the simultaneous monitoring of cell voltage, cell current, cell temperature, and package strain, indicative of swelling and increased internal pressure, (3) small receivers compatible with USB ports on portable computers; (4) software drivers and logging software; (5) a 7S2P battery simulator, enabling the safe development of wireless BMS hardware in the laboratory; (6) demonstrated data transmission out of metal enclosures, including battery box, with small variable aperture opening; (7) test data demonstrating the accurate and reliable operation of sensors, with transmission of terminal voltage, cell temperature and package strain at distances up to 110 feet; (8) quantification of the data transmission error as a function of distance, in both indoor and outdoor operation; (9) electromagnetic interference testing during operation with live, high-capacity battery management system at Yardney Technical Products; (10) demonstrated operation with live high-capacity lithium-ion battery pack during charge-discharge cycling; (11) development of special polymer-gel lithium-ion batteries with embedded temperature sensors, capable of measuring the core temperature of individual of the cells during charge

ARPA-E Program: Advanced Management Protection of Energy Storage Devices (AMPED) - Monthly Report - November 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, J.

Technology has been developed that enables monitoring of individual cells in high - capacity lithium-ion battery packs, with a distributed array of wireless Bluetooth 4.0 tags and sensors, and without proliferation of extensive wiring harnesses. Given the safety challenges facing lithium-ion batteries in electric vehicle, civilian aviation and defense applications, these wireless sensors may be particularly important to these emerging markets. These wireless sensors will enhance the performance, reliability and safety of such energy storage systems. Specific accomplishments to date include, but are not limited to: (1) the development of wireless tags using Bluetooth 4.0 standard to monitor a largemore » array of sensors in battery pack; (2) sensor suites enabling the simultaneous monitoring of cell voltage, cell current, cell temperature, and package strain, indicative of swelling and increased internal pressure, (3) small receivers compatible with USB ports on portable computers; (4) software drivers and logging software; (5) a 7S2P battery simulator, enabling the safe development of wireless BMS hardware in the laboratory; (6) demonstrated data transmission out of metal enclosures, including battery box, with small variable aperture opening; (7) test data demonstrating the accurate and reliable operation of sensors, with transmission of terminal voltage, cell temperature and package strain at distances up to 110 feet; (8) quantification of the data transmission error as a function of distance, in both indoor and outdoor operation; (9) electromagnetic interference testing during operation with live, high -capacity battery management system at Yardney Technical Products; (10) demonstrat ed operation with live high-capacity lithium-ion battery pack during charge-discharge cycling; (11) development of special polymer-gel lithium-ion batteries with embedded temperature sensors, capable of measuring the core temperature of individual of the cells during charge

A Survey on Energy Conserving Mechanisms for the Internet of Things: Wireless Networking Aspects.

PubMed

Abbas, Zeeshan; Yoon, Wonyong

2015-09-25

The Internet of Things (IoT) is an emerging key technology for future industries and everyday lives of people, where a myriad of battery operated sensors, actuators, and smart objects are connected to the Internet to provide services such as mobile healthcare, intelligent transport system, environmental monitoring, etc. Since energy efficiency is of utmost importance to these battery constrained IoT devices, IoT-related standards and research works have focused on the device energy conserving issues. This paper presents a comprehensive survey on energy conserving issues and solutions in using diverse wireless radio access technologies for IoT connectivity, e.g., the 3rd Generation Partnership Project (3GPP) machine type communications, IEEE 802.11ah, Bluetooth Low Energy (BLE), and Z-Wave. We look into the literature in broad areas of standardization, academic research, and industry development, and structurally summarize the energy conserving solutions based on several technical criteria. We also propose future research directions regarding energy conserving issues in wireless networking-based IoT.

Smart TV-Smartphone Multiscreen Interactive Middleware for Public Displays.

PubMed

Martinez-Pabon, Francisco; Caicedo-Guerrero, Jaime; Ibarra-Samboni, Jhon Jairo; Ramirez-Gonzalez, Gustavo; Hernández-Leo, Davinia

2015-01-01

A new generation of public displays demands high interactive and multiscreen features to enrich people's experience in new pervasive environments. Traditionally, research on public display interaction has involved mobile devices as the main characters during the use of personal area network technologies such as Bluetooth or NFC. However, the emergent Smart TV model arises as an interesting alternative for the implementation of a new generation of public displays. This is due to its intrinsic connection capabilities with surrounding devices like smartphones or tablets. Nonetheless, the different approaches proposed by the most important vendors are still underdeveloped to support multiscreen and interaction capabilities for modern public displays, because most of them are intended for domestic environments. This research proposes multiscreen interactive middleware for public displays, which was developed from the principles of a loosely coupled interaction model, simplicity, stability, concurrency, low latency, and the usage of open standards and technologies. Moreover, a validation prototype is proposed in one of the most interesting public display scenarios: the advertising.

Implementation experiences of ISO/IEEE11073 standard applied to new use cases for e-health environments.

PubMed

Martinez, I; Escayola, J; Martinez-Espronceda, M; Serrano, L; Trigo, J D; Led, S; Garcia, J

2009-01-01

Recent advances in biomedical engineering and continuous technological innovations in last decade are promoting new challenges, especially in e-Health environments. In this context, the medical devices interoperability is one of the interest fields wherein these improvements require a standard-based design in order to achieve homogeneous solutions. Furthermore, the spreading of wearable devices, oriented to the paradigm of patient environment and supported by wireless technologies as Bluetooth or ZigBee, is bringing new medical use cases based on Ambient Assisted Living, home monitoring of elderly, heart failure, chronic, under palliative care or patients who have undergone surgery, urgencies and emergencies, or even fitness auto-control and health follow-up. In this paper, several implementation experiences based on ISO/IEEE11073 standard are detailed. These evolved e-Health services can improve the quality of the patient's care, increase the user's interaction, and assure these e-Health applications to be fully compatible with global telemedicine systems.

Location-Enhanced Activity Recognition in Indoor Environments Using Off the Shelf Smart Watch Technology and BLE Beacons.

PubMed

Filippoupolitis, Avgoustinos; Oliff, William; Takand, Babak; Loukas, George

2017-05-27

Activity recognition in indoor spaces benefits context awareness and improves the efficiency of applications related to personalised health monitoring, building energy management, security and safety. The majority of activity recognition frameworks, however, employ a network of specialised building sensors or a network of body-worn sensors. As this approach suffers with respect to practicality, we propose the use of commercial off-the-shelf devices. In this work, we design and evaluate an activity recognition system composed of a smart watch, which is enhanced with location information coming from Bluetooth Low Energy (BLE) beacons. We evaluate the performance of this approach for a variety of activities performed in an indoor laboratory environment, using four supervised machine learning algorithms. Our experimental results indicate that our location-enhanced activity recognition system is able to reach a classification accuracy ranging from 92% to 100%, while without location information classification accuracy it can drop to as low as 50% in some cases, depending on the window size chosen for data segmentation.

Philosophy of Technology Assumptions in Educational Technology Leadership: Questioning Technological Determinism

ERIC Educational Resources Information Center

Webster, Mark David

2013-01-01

Scholars have emphasized that decisions about technology can be influenced by philosophy of technology assumptions, and have argued for research that critically questions technological determinist assumptions. Empirical studies of technology management in fields other than K-12 education provided evidence that philosophy of technology assumptions,…

Design and implementation of a wearable healthcare monitoring system.

PubMed

Sagahyroon, Assim; Raddy, Hazem; Ghazy, Ali; Suleman, Umair

2009-01-01

A wearable healthcare monitoring unit that integrates various technologies was developed to provide patients with the option of leading a healthy and independent life without risks or confinement to medical facilities. The unit consists of various sensors integrated to a microcontroller and attached to the patient's body, reading vital signs and transmitting these readings via a Bluetooth link to the patient's mobile phone. Short-Messaging-Service (SMS) is incorporated in the design to alert a physician in emergency cases. Additionally, an application program running on the mobile phone uses the internet to update (at regular intervals) the patient records in a hospital database with the most recent readings. To reduce development costs, the components used were both off-the-shelf and affordable.

Technology CAD for integrated circuit fabrication technology development and technology transfer

NASA Astrophysics Data System (ADS)

Saha, Samar

2003-07-01

In this paper systematic simulation-based methodologies for integrated circuit (IC) manufacturing technology development and technology transfer are presented. In technology development, technology computer-aided design (TCAD) tools are used to optimize the device and process parameters to develop a new generation of IC manufacturing technology by reverse engineering from the target product specifications. While in technology transfer to manufacturing co-location, TCAD is used for process centering with respect to high-volume manufacturing equipment of the target manufacturing equipment of the target manufacturing facility. A quantitative model is developed to demonstrate the potential benefits of the simulation-based methodology in reducing the cycle time and cost of typical technology development and technology transfer projects over the traditional practices. The strategy for predictive simulation to improve the effectiveness of a TCAD-based project, is also discussed.

SUPERFUND INNOVATIVE TECHNOLOGY EVALUATION - TECHNOLOGY PROFILES

EPA Science Inventory

This document is intended as a reference guide for EPA Regional decision makers and others interested in technologies in the SITE Demonstration and Emerging Technologies programs. The Technologies are described in technology profiles, presented in alphabetical order by developer ...

Development of data communication system with ultra high frequency radio wave for implantable artificial hearts.

PubMed

Tsujimura, Shinichi; Yamagishi, Hiroto; Sankai, Yoshiyuki

2009-01-01

In order to minimize infection risks of patients with artificial hearts, wireless data transmission methods with electromagnetic induction or light have been developed. However, these methods tend to become difficult to transmit data if the external data transmission unit moves from its proper position. To resolve this serious problem, the purpose of this study is to develop a prototype wireless data communication system with ultra high frequency radio wave and confirm its performance. Due to its high-speed communication rate, low power consumption, high tolerance to electromagnetic disturbances, and secure wireless communication, we adopted Bluetooth radio wave technology for our system. The system consists of an internal data transmission unit and an external data transmission unit (53 by 64 by 16 mm, each), and each has a Bluetooth module (radio field intensity: 4 dBm, receiver sensitivity: -80 dBm). The internal unit also has a micro controller with an 8-channel 10-bit A/D converter, and the external unit also has a RS-232C converter. We experimented with the internal unit implanted into pig meat, and carried out data transmission tests to evaluate the performance of this system in tissue thickness of up to 3 mm. As a result, data transfer speeds of about 20 kbps were achieved within the communication distance of 10 m. In conclusion, we confirmed that the system can wirelessly transmit the data from the inside of the body to the outside, and it promises to resolve unstable data transmission due to accidental movements of an external data transmission unit.

Development of Communication Assistive Technology for Persons with Deaf-Blindness and Physical Limitation.

PubMed

Hatakeyama, Takuro; Watanabe, Takashi; Takahashi, Kiriko; Doi, Kouki; Fukuda, Akiko

2015-01-01

The purpose of this study was to develop a system that will provide communication assistance to persons with deaf-blindness and physical limitation, so that they will be able to communicate with others without the help of an interpreter. With this communication system, a person with deaf-blindness and physical limitation uses a control switch to perform input operations based on the duration of the operating time and combination of long and short pulses. When the input is correctly performed, the user receives a feedback from the tablet computer as vibratory stimuli. Similarly, the message that other person's input with a Bluetooth keyboard is transmitted to the user as vibration stimuli. Following the development, we conducted a one-year assessment of the developed communication system in an actual environment with the cooperation of one person with deaf-blindness and physical limitation. . We confirmed that our developed system was useful for such a person, and understood that we must improve upon several aspects. We shall pursue further study, and will aim at providing a better communication environment for persons with deaf-blindness and physical limitation in future.

A Browser-Server-Based Tele-audiology System That Supports Multiple Hearing Test Modalities

PubMed Central

Yao, Daoyuan; Givens, Gregg

2015-01-01

Abstract Introduction: Millions of global citizens suffering from hearing disorders have limited or no access to much needed hearing healthcare. Although tele-audiology presents a solution to alleviate this problem, existing remote hearing diagnosis systems support only pure-tone tests, leaving speech and other test procedures unsolved, due to the lack of software and hardware to enable communication required between audiologists and their remote patients. This article presents a comprehensive remote hearing test system that integrates the two most needed hearing test procedures: a pure-tone audiogram and a speech test. Materials and Methods: This enhanced system is composed of a Web application server, an embedded smart Internet-Bluetooth® (Bluetooth SIG, Kirkland, WA) gateway (or console device), and a Bluetooth-enabled audiometer. Several graphical user interfaces and a relational database are hosted on the application server. The console device has been designed to support the tests and auxiliary communication between the local site and the remote site. Results: The study was conducted at an audiology laboratory. Pure-tone audiogram and speech test results from volunteers tested with this tele-audiology system are comparable with results from the traditional face-to-face approach. Conclusions: This browser-server–based comprehensive tele-audiology offers a flexible platform to expand hearing services to traditionally underserved groups. PMID:25919376

An optimized low-power voltage controlled oscillator

NASA Astrophysics Data System (ADS)

Shah, Kriyang; Le, Hai Phuong; Singh, Jugdutt

2007-01-01

This paper presents an optimised low-power low-phase-noise Voltage Controlled Oscillator (VCO) for Bluetooth wireless applications. The system level design issues and tradeoffs related to Direct Conversion Receiver (DCR) and Low Intermediate Frequency (IF) architecture for Bluetooth are discussed. Subsequently, for a low IF architecture, the critical VCO performance parameters are derived from system specifications. The VCO presented in the paper is optimised by implementing a novel biasing circuit that employs two current mirrors, one at the top and the other one at the bottom of the cross-coupled complementary VCO, to give the exact replica of the current in both the arms of current mirror circuit. This approach, therefore, significantly reduces the system power consumption as well as improves the system performance. Results show that, the VCO consumes only 281μW of power at 2V supply. Its phase noise performance are -115dBc/Hz, -130dBc/Hz and -141dBc/Hz at the offset frequency of 1MHz, 3MHz and 5MHz respectively. Results indicate that 31% reduction in power consumption is achieved as compared to the traditional VCO design. These characteristics make the designed VCO a better candidate for Bluetooth wireless application where power consumption is the major issue.

A low noise remotely controllable wireless telemetry system for single-unit recording in rats navigating in a vertical maze.

PubMed

Chen, Hsin-Yung; Wu, Jin-Shang; Hyland, Brian; Lu, Xiao-Dong; Chen, Jia Jin Jason

2008-08-01

The use of cables for recording neural activity limits the scope of behavioral tests used in conscious free-moving animals. Particularly, cable attachments make it impossible to record in three-dimensional (3D) mazes where levels are vertically stacked or in enclosed spaces. Such environments are of particular interest in investigations of hippocampal place cells, in which neural activity is correlated with spatial position in the environment. We developed a flexible miniaturized Bluetooth-based wireless data acquisition system. The wireless module included an 8-channel analogue front end, digital controller, and Bluetooth transceiver mounted on a backpack. Our bidirectional wireless design allowed all data channels to be previewed at 1 kHz sample rate, and one channel, selected by remote control, to be sampled at 10 kHz. Extracellular recordings of neuronal activity are highly susceptible to ambient electrical noise due to the high electrode impedance. Through careful design of appropriate shielding and hardware configuration to avoid ground loops, mains power and Bluetooth hopping frequency noise were reduced sufficiently to yield signal quality comparable to those recorded by wired systems. With this system we were able to obtain single-unit recordings of hippocampal place cells in rats running an enclosed vertical maze, over a range of 5 m.

A Browser-Server-Based Tele-audiology System That Supports Multiple Hearing Test Modalities.

PubMed

Yao, Jianchu Jason; Yao, Daoyuan; Givens, Gregg

2015-09-01

Millions of global citizens suffering from hearing disorders have limited or no access to much needed hearing healthcare. Although tele-audiology presents a solution to alleviate this problem, existing remote hearing diagnosis systems support only pure-tone tests, leaving speech and other test procedures unsolved, due to the lack of software and hardware to enable communication required between audiologists and their remote patients. This article presents a comprehensive remote hearing test system that integrates the two most needed hearing test procedures: a pure-tone audiogram and a speech test. This enhanced system is composed of a Web application server, an embedded smart Internet-Bluetooth(®) (Bluetooth SIG, Kirkland, WA) gateway (or console device), and a Bluetooth-enabled audiometer. Several graphical user interfaces and a relational database are hosted on the application server. The console device has been designed to support the tests and auxiliary communication between the local site and the remote site. The study was conducted at an audiology laboratory. Pure-tone audiogram and speech test results from volunteers tested with this tele-audiology system are comparable with results from the traditional face-to-face approach. This browser-server-based comprehensive tele-audiology offers a flexible platform to expand hearing services to traditionally underserved groups.

How Technology Teachers Understand Technological Knowledge

ERIC Educational Resources Information Center

Norström, Per

2014-01-01

Swedish technology teachers' views of technological knowledge are examined through a written survey and a series of interviews. The study indicates that technology teachers' understandings of what constitutes technological knowledge and how it is justified vary considerably. The philosophical discussions on the topic are unknown to them. This lack…

Appropriate Technology as Indian Technology.

ERIC Educational Resources Information Center

Barry, Tom

1979-01-01

Describes the mounting enthusiasm of Indian communities for appropriate technology as an inexpensive means of providing much needed energy and job opportunities. Describes the development of several appropriate technology projects, and the goals and activities of groups involved in utilizing low scale solar technology for economic development on…

Penetration of High Intensity Radiated Fields (HIRF) Into General Aviation Aircraft

NASA Technical Reports Server (NTRS)

Balanis, Constantine A.; Birtcher, Craig R.; Georgakopoulos, Stavros V.; Panaretos, Anastasios H.

2004-01-01

The ability to design and achieve electromagnetic compatibility is becoming more challenging with the rapid development of new electronic products and technologies. The importance of electromagnetic interference (EMI) and electromagnetic compatibility (EMC) issues stems from the fact that the ambient electromagnetic environment has become very hostile; that is, it increases both in density and intensity, while the current trend in technology suggests the number of electronic devices increases in homes, businesses, factories, and transportation vehicles. Furthermore, the operating frequency of products coming into the market continuously increases. While cell phone technology has exceeded 1 GHz and Bluetooth operates at 2.4 GHz, products involving satellite communications operate near 10 GHz and automobile radar systems involve frequencies above 40 GHz. The concern about higher frequencies is that they correspond to smaller wavelengths, therefore electromagnetic waves are able to penetrate equipment enclosure through apertures or even small cracks more easily. In addition, electronic circuits have become small in size, and they are usually placed on motherboards or housed in boxes in very close proximity. Cosite interference and coupling in all electrical and electronic circuit assemblies are two essential issues that have to be examined in every design.

Computational Electrocardiography: Revisiting Holter ECG Monitoring.

PubMed

Deserno, Thomas M; Marx, Nikolaus

2016-08-05

Since 1942, when Goldberger introduced the 12-lead electrocardiography (ECG), this diagnostic method has not been changed. After 70 years of technologic developments, we revisit Holter ECG from recording to understanding. A fundamental change is fore-seen towards "computational ECG" (CECG), where continuous monitoring is producing big data volumes that are impossible to be inspected conventionally but require efficient computational methods. We draw parallels between CECG and computational biology, in particular with respect to computed tomography, computed radiology, and computed photography. From that, we identify technology and methodology needed for CECG. Real-time transfer of raw data into meaningful parameters that are tracked over time will allow prediction of serious events, such as sudden cardiac death. Evolved from Holter's technology, portable smartphones with Bluetooth-connected textile-embedded sensors will capture noisy raw data (recording), process meaningful parameters over time (analysis), and transfer them to cloud services for sharing (handling), predicting serious events, and alarming (understanding). To make this happen, the following fields need more research: i) signal processing, ii) cycle decomposition; iii) cycle normalization, iv) cycle modeling, v) clinical parameter computation, vi) physiological modeling, and vii) event prediction. We shall start immediately developing methodology for CECG analysis and understanding.

Advanced Refrigerator/Freezer Technology Development. Technology Assessment

NASA Technical Reports Server (NTRS)

Gaseor, Thomas; Hunter, Rick; Hamill, Doris

1996-01-01

The NASA Lewis Research Center, through contract with Oceaneering Space Systems, is engaged in a project to develop advanced refrigerator/freezer (R/F) technologies for future Life and Biomedical Sciences space flight missions. The first phase of this project, a technology assessment, has been completed to identify the advanced R/F technologies needed and best suited to meet the requirements for the five R/F classifications specified by Life and Biomedical Science researchers. Additional objectives of the technology assessment were to rank those technologies based on benefit and risk, and to recommend technology development activities that can be accomplished within this project. This report presents the basis, the methodology, and results of the R/F technology assessment, along with technology development recommendations.

Towards a Mobile Intelligent Information System with Application to HIV/AIDS.

PubMed

Kopec, D; Eckhardt, R; Tamang, S; Reinharth, D

2005-01-01

The United Nations Security Council reports HIV/AIDS as the fastest growing threat to human development. In addition, the World Health Organization [1] reports that nearly 5 million persons (4.3 million adults and 700,000 children) are newly infected with HIV each year; more than 95% of them found in developing countries. Since STDs as a group are a personal problem which few people feel comfortable discussing, we believe that hand-held PDAs can provide an opportunity for learning about this disease while insuring anonymity. This device will employ the newest technologies including Bluetooth wireless technology, which can transmit and receive data via a short-range radio link using a globally available frequency band (2.4 GHz ISM band), enabling rapid and accurate synchronous and asynchronous data communication. The first generation of Bluetooth permits exchange of data up to a rate of 1 Mbps, even in areas with much electromagnetic disturbance. This emerging technology can facilitate HIV/AIDS outreach around the globe.Recent advances in learning have taken a particularly cognitive perspective and these findings have implications for education in general as well as for the development of intelligent tutoring systems in particular. In the past, effective SmartBookstrade markhave been developed for AIDS education to disseminate the critical knowledge relevant to this epidemic [2].Since 1993, the proliferation of the World Wide Web has created a plethora of new opportunities for the delivery of electronic distance learning systems. However, we feel that it is important that a whatever technology is employed is based on a sound educational theory. A new, comprehensive, web-based learning system called SmartTutor has been developed, at Brooklyn College of The City University of New York [3]. This technology provides a user-friendly, self-paced, easy to modify, software environment intended to serve the user's learning needs and is based on a generic Smart

Smart Rehabilitation Garment for posture monitoring.

PubMed

Wang, Q; Chen, W; Timmermans, A A A; Karachristos, C; Martens, J B; Markopoulos, P

2015-08-01

Posture monitoring and correction technologies can support prevention and treatment of spinal pain or can help detect and avoid compensatory movements during the neurological rehabilitation of upper extremities, which can be very important to ensure their effectiveness. We describe the design and development of Smart Rehabilitation Garment (SRG) a wearable system designed to support posture correction. The SRG combines a number of inertial measurement units (IMUs), controlled by an Arduino processor. It provides feedback with vibration on the garment, audible alarm signals and visual instruction through a Bluetooth connected smartphone. We discuss the placement of sensing modules, the garment design, the feedback design and the integration of smart textiles and wearable electronics which aimed at achieving wearability and ease of use. We report on the system's accuracy as compared to optical tracker method.

Triboelectret-based aeroelastic flutter energy harvesters

NASA Astrophysics Data System (ADS)

Perez, Matthias; Boisseau, Sebastien; Geisler, Matthias; Despesse, Ghislain; Reboud, Jean Luc

2016-11-01

This paper highlights some experimental results on several electrostatic membranes tested in a wind tunnel between 0 and 20m.s-1 for airflow energy harvesting. The main idea is to use the aeroelastic behavior of thin flexible films to induce simultaneously the capacitance variations and the polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and avoids the issue of electrets discharge. Our prototypes (<16cm2) allowed a quick startup (from 3ms-1), an electrical power-flux density from 0.1μW.cm-2 to 60μW.cm-2. In order to complete the energy harvesting chain, we have used a wireless sensor with temperature and acceleration measures coupled to a low power transmission (Bluetooth Low Energy) with reception on a smartphone.

Ubiquitous Connected Train Based on Train-to-Ground and Intra-Wagon Communications Capable of Providing on Trip Customized Digital Services for Passengers

PubMed Central

Salaberria, Itziar; Perallos, Asier; Azpilicueta, Leire; Falcone, Francisco; Carballedo, Roberto; Angulo, Ignacio; Elejoste, Pilar; Bahillo, Alfonso; Astrain, José Javier; Villadangos, Jesús

2014-01-01

During the last years, the application of different wireless technologies has been explored in order to enable Internet connectivity from vehicles. In addition, the widespread adoption of smartphones by citizens represents a great opportunity to integrate such nomadic devices inside vehicles in order to provide new and personalized on trip services for passengers. In this paper, a proposal of communication architecture to provide the ubiquitous connectivity needed to enhance the smart train concept is presented and preliminarily tested. It combines an intra-wagon communication system based on nomadic devices connected through a Bluetooth Piconet Network with a highly innovative train-to-ground communication system. In order to validate this communication solution, several tests and simulations have been performed and their results are described in this paper. PMID:24803192

Safe pill-dispensing.

PubMed

Testa, Massimiliano; Pollard, John

2007-01-01

Each patient is supplied with a smart-card containing a Radio Frequency IDentification (RFID) chip storing a unique identification code. The patient places the Smart-card on a pill-dispenser unit containing an RFID reader. The RFID chip is read and the code sent to a Base-station via a wireless Bluetooth link. A database containing both patient details and treatment information is queried at the Base-station using the RFID as the search key. The patient's treatment data (i.e., drug names, quantities, time, etc.) are retrieved and sent back to the pill-dispenser unit via Bluetooth. Appropriate quantities of the required medications are automatically dispensed, unless the patient has already taken his/her daily dose. Safe, confidential communication and operation is ensured.

Be the Technology: Redefining Technology Integration in Classrooms.

ERIC Educational Resources Information Center

Mills, Steven C.; Tincher, Robert C.

A technology professional development initiative was launched in a school district with the goal of extending technology use in the classroom. For teachers to teach expertly, the aim was for them to "be the technology" by modeling technology use in the classroom, applying technology across the curriculum, applying technology to…

Technology and Economics, Inc. Technology Application Team

NASA Technical Reports Server (NTRS)

Ballard, T.; Macfadyen, D. J.

1981-01-01

Technology + Economics, Inc. (T+E), under contract to the NASA Headquarters Technology Transfer Division, operates a Technology Applications Team (TATeam) to assist in the transfer of NASA-developed aerospace technology. T+E's specific areas of interest are selected urban needs at the local, county, and state levels. T+E contacts users and user agencies at the local, state, and county levels to assist in identifying significant urban needs amenable to potential applications of aerospace technology. Once viable urban needs have been identified in this manner, or through independent research, T+E searches the NASA technology database for technology and/or expertise applicable to the problem. Activities currently under way concerning potential aerospace applications are discussed.

Location-Enhanced Activity Recognition in Indoor Environments Using Off the Shelf Smart Watch Technology and BLE Beacons

PubMed Central

Filippoupolitis, Avgoustinos; Oliff, William; Takand, Babak; Loukas, George

2017-01-01

Activity recognition in indoor spaces benefits context awareness and improves the efficiency of applications related to personalised health monitoring, building energy management, security and safety. The majority of activity recognition frameworks, however, employ a network of specialised building sensors or a network of body-worn sensors. As this approach suffers with respect to practicality, we propose the use of commercial off-the-shelf devices. In this work, we design and evaluate an activity recognition system composed of a smart watch, which is enhanced with location information coming from Bluetooth Low Energy (BLE) beacons. We evaluate the performance of this approach for a variety of activities performed in an indoor laboratory environment, using four supervised machine learning algorithms. Our experimental results indicate that our location-enhanced activity recognition system is able to reach a classification accuracy ranging from 92% to 100%, while without location information classification accuracy it can drop to as low as 50% in some cases, depending on the window size chosen for data segmentation. PMID:28555022

Living technology: exploiting life's principles in technology.

PubMed

Bedau, Mark A; McCaskill, John S; Packard, Norman H; Rasmussen, Steen

2010-01-01

The concept of living technology-that is, technology that is based on the powerful core features of life-is explained and illustrated with examples from artificial life software, reconfigurable and evolvable hardware, autonomously self-reproducing robots, chemical protocells, and hybrid electronic-chemical systems. We define primary (secondary) living technology according as key material components and core systems are not (are) derived from living organisms. Primary living technology is currently emerging, distinctive, and potentially powerful, motivating this review. We trace living technology's connections with artificial life (soft, hard, and wet), synthetic biology (top-down and bottom-up), and the convergence of nano-, bio-, information, and cognitive (NBIC) technologies. We end with a brief look at the social and ethical questions generated by the prospect of living technology.

Digital SPC switching technology: Foreign technology assessment

NASA Astrophysics Data System (ADS)

Fischman, Kurt; Jorstad, Norman D.

1990-12-01

This paper provides a foreign technology assessment of digital switching technology. Leading suppliers of digital switching technology are identified; although the United States holds a large part of the market, major companies in France, Sweden, Japan, the U.K., and Germany are also important. These countries, along with Belgium and Canada, are the most innovative and technically advanced. A listing is provided of transfers of digital switching technology to non-COCOM countries through licensing and joint ventures which reflects the widespread dissemination of this technology. Detailed technical specifications are provided for selected digital switching systems worldwide. The report concludes that considering the degree to which the technology is in place, that control of digital switching technology may not be feasible.

Technology Transfer: Marketing Tomorrow's Technology

NASA Technical Reports Server (NTRS)

Tcheng, Erene

1995-01-01

The globalization of the economy and the end of the Cold War have triggered many changes in the traditional practices of U.S. industry. To effectively apply the resources available to the United States, the federal government has firmly advocated a policy of technology transfer between private industry and government labs, in this case the National Aeronautics and Space Administration (NASA). NASA Administrator Daniel Goldin is a strong proponent of this policy and has organized technology transfer or commercialization programs at each of the NASA field centers. Here at Langley Research Center, the Technology Applications Group (TAG) is responsible for facilitating the transfer of Langley developed research and technology to U.S. industry. Entering the program, I had many objectives for my summer research with TAG. Certainly, I wanted to gain a more thorough understanding of the concept of technology transfer and Langley's implementation of a system to promote it to both the Langley community and the community at large. Also, I hoped to become more familiar with Langley's research capabilities and technology inventory available to the public. More specifically, I wanted to learn about the technology transfer process at Langley. Because my mentor is a member of Materials and Manufacturing marketing sector of the Technology Transfer Team, another overriding objective for my research was to take advantage of his work and experience in materials research to learn about the Advanced Materials Research agency wide and help market these developments to private industry. Through the various projects I have been assigned to work on in TAG, I have successfully satisfied the majority of these objectives. Work on the Problem Statement Process for TAG as well as the development of the Advanced Materials Research Brochure have provided me with the opportunity to learn about the technology transfer process from the outside looking in and the inside looking out. Because TAG covers

Applications of aerospace technology in industry. A technology transfer profile: Food technology

NASA Technical Reports Server (NTRS)

Murray, D. M.

1971-01-01

Food processing and preservation technologies are reviewed, expected technological advances are considered including processing and market factors. NASA contributions to food technology and nutrition are presented with examples of transfer from NASA to industry.

Older Adults Talk Technology: Technology Usage and Attitudes.

PubMed

Mitzner, Tracy L; Boron, Julie B; Fausset, Cara Bailey; Adams, Anne E; Charness, Neil; Czaja, Sara J; Dijkstra, Katinka; Fisk, Arthur D; Rogers, Wendy A; Sharit, Joseph

2010-11-01

Older adults (n = 113) participated in focus groups discussing their use of and attitudes about technology in the context of their home, work, and healthcare. Participants reported using a wide variety of technology items, particularly in their homes. Positive attitudes (i.e., likes) outnumbered negative attitudes (i.e., dislikes), suggesting that older adults perceive the benefits of technology use to outweigh the costs of such use. Positive attitudes were most frequently related to how the technology supported activities, enhanced convenience, and contained useful features. Negative attitudes were most frequently associated with technology creating inconveniences, unhelpful features, as well as security and reliability concerns. Given that older adults reported more positive than negative attitudes about the technologies they use, these results contradict stereotypes that older adults are afraid or unwilling to use technology. These findings also highlight the importance of perceived benefits of use and ease of use for models of technology acceptance. Emphasizing the benefits of technology in education and training programs may increase future technology adoption.

Space Transportation Technology Workshop: Propulsion Research and Technology

NASA Technical Reports Server (NTRS)

2000-01-01

This viewgraph presentation gives an overview of the Space Transportation Technology Workshop topics, including Propulsion Research and Technology (PR&T) project level organization, FY 2001 - 2006 project roadmap, points of contact, foundation technologies, auxiliary propulsion technology, PR&T Low Cost Turbo Rocket, and PR&T advanced reusable technologies RBCC test bed.

Prioritizing Information Technology Investments: Assessing the Correlations among Technological Readiness, Information Technology Flexibility, and Information Technology Effectiveness

ERIC Educational Resources Information Center

Walter, John T.

2010-01-01

Management's dilemma, when allocating financial resources towards the improvement of technological readiness and IT flexibility within their organizations, is to control financial risk and maximize IT effectiveness. Technological readiness is people's propensity to embrace and use technology. Its drivers are optimism, innovativeness, discomfort,…

[Design of Oxygen Saturation, Heart Rate, Respiration Rate Detection System Based on Smartphone of Android Operating System].

PubMed

Zhu, Mingshan; Zeng, Bixin

2015-03-01

In this paper, we designed an oxygen saturation, heart rate, respiration rate monitoring system based on smartphone of android operating system, physiological signal acquired by MSP430 microcontroller and transmitted by Bluetooth module.

Integration of High-Resolution Laser Displacement Sensors and 3D Printing for Structural Health Monitoring

PubMed Central

Chang, Shu-Wei; Kuo, Shih-Yu; Huang, Ting-Hsuan

2017-01-01

This paper presents a novel experimental design for complex structural health monitoring (SHM) studies achieved by integrating 3D printing technologies, high-resolution laser displacement sensors, and multiscale entropy SHM theory. A seven-story structure with a variety of composite bracing systems was constructed using a dual-material 3D printer. A wireless Bluetooth vibration speaker was used to excite the ground floor of the structure, and high-resolution laser displacement sensors (1-μm resolution) were used to monitor the displacement history on different floors. Our results showed that the multiscale entropy SHM method could detect damage on the 3D-printed structures. The results of this study demonstrate that integrating 3D printing technologies and high-resolution laser displacement sensors enables the design of cheap, fast processing, complex, small-scale civil structures for future SHM studies. The novel experimental design proposed in this study provides a suitable platform for investigating the validity and sensitivity of SHM in different composite structures and damage conditions for real life applications in the future. PMID:29271937

Integration of High-Resolution Laser Displacement Sensors and 3D Printing for Structural Health Monitoring.

PubMed

Chang, Shu-Wei; Lin, Tzu-Kang; Kuo, Shih-Yu; Huang, Ting-Hsuan

2017-12-22

This paper presents a novel experimental design for complex structural health monitoring (SHM) studies achieved by integrating 3D printing technologies, high-resolution laser displacement sensors, and multiscale entropy SHM theory. A seven-story structure with a variety of composite bracing systems was constructed using a dual-material 3D printer. A wireless Bluetooth vibration speaker was used to excite the ground floor of the structure, and high-resolution laser displacement sensors (1-μm resolution) were used to monitor the displacement history on different floors. Our results showed that the multiscale entropy SHM method could detect damage on the 3D-printed structures. The results of this study demonstrate that integrating 3D printing technologies and high-resolution laser displacement sensors enables the design of cheap, fast processing, complex, small-scale civil structures for future SHM studies. The novel experimental design proposed in this study provides a suitable platform for investigating the validity and sensitivity of SHM in different composite structures and damage conditions for real life applications in the future.

HealthBand for Dementia Patients: Fall and Scream Detector and Caretaker Helper

NASA Astrophysics Data System (ADS)

Alam, Zeeshan; Samin, Huma; Samin, Omar Bin

2018-02-01

The ratio of dementia patients is escalating with time and requires proper attention to help the people suffering from it to continue their activities of daily living (ADL). Such patients suffer from the symptoms like irregular sleep patterns, restlessness, wandering, screaming, falling, sadness and depression. Assistive Technology facilitates caretaker to aid the patient efficiently with minimum effort. Advances in technology have made possible state of the art and innovative methods of health care delivery. Home telecare; in which the patient’s health is monitored remotely at home, is one such method. This paper is proposing a cost effective and user friendly wearable product based solution (i.e. HealthBand) that monitors patient’s activities (specifically fall and scream) and notifies the caretaker in case of emergency to take appropriate action(s). These notifications are sent to the caretaker on the basis of predefined threshold and time span over Bluetooth and GSM mediums to android based application. The android app also keeps patient’s medicines’ intake record and reminds caretaker regarding medicine dosage and timings.

A Survey on Energy Conserving Mechanisms for the Internet of Things: Wireless Networking Aspects

PubMed Central

Abbas, Zeeshan; Yoon, Wonyong

2015-01-01

The Internet of Things (IoT) is an emerging key technology for future industries and everyday lives of people, where a myriad of battery operated sensors, actuators, and smart objects are connected to the Internet to provide services such as mobile healthcare, intelligent transport system, environmental monitoring, etc. Since energy efficiency is of utmost importance to these battery constrained IoT devices, IoT-related standards and research works have focused on the device energy conserving issues. This paper presents a comprehensive survey on energy conserving issues and solutions in using diverse wireless radio access technologies for IoT connectivity, e.g., the 3rd Generation Partnership Project (3GPP) machine type communications, IEEE 802.11ah, Bluetooth Low Energy (BLE), and Z-Wave. We look into the literature in broad areas of standardization, academic research, and industry development, and structurally summarize the energy conserving solutions based on several technical criteria. We also propose future research directions regarding energy conserving issues in wireless networking-based IoT. PMID:26404275

Smart TV-Smartphone Multiscreen Interactive Middleware for Public Displays

PubMed Central

Martinez-Pabon, Francisco; Caicedo-Guerrero, Jaime; Ibarra-Samboni, Jhon Jairo; Ramirez-Gonzalez, Gustavo; Hernández-Leo, Davinia

2015-01-01

A new generation of public displays demands high interactive and multiscreen features to enrich people's experience in new pervasive environments. Traditionally, research on public display interaction has involved mobile devices as the main characters during the use of personal area network technologies such as Bluetooth or NFC. However, the emergent Smart TV model arises as an interesting alternative for the implementation of a new generation of public displays. This is due to its intrinsic connection capabilities with surrounding devices like smartphones or tablets. Nonetheless, the different approaches proposed by the most important vendors are still underdeveloped to support multiscreen and interaction capabilities for modern public displays, because most of them are intended for domestic environments. This research proposes multiscreen interactive middleware for public displays, which was developed from the principles of a loosely coupled interaction model, simplicity, stability, concurrency, low latency, and the usage of open standards and technologies. Moreover, a validation prototype is proposed in one of the most interesting public display scenarios: the advertising. PMID:25950018

Older Adults Talk Technology: Technology Usage and Attitudes

PubMed Central

Mitzner, Tracy L.; Boron, Julie B.; Fausset, Cara Bailey; Adams, Anne E.; Charness, Neil; Czaja, Sara J.; Dijkstra, Katinka; Fisk, Arthur D.; Rogers, Wendy A.; Sharit, Joseph

2010-01-01

Older adults (n = 113) participated in focus groups discussing their use of and attitudes about technology in the context of their home, work, and healthcare. Participants reported using a wide variety of technology items, particularly in their homes. Positive attitudes (i.e., likes) outnumbered negative attitudes (i.e., dislikes), suggesting that older adults perceive the benefits of technology use to outweigh the costs of such use. Positive attitudes were most frequently related to how the technology supported activities, enhanced convenience, and contained useful features. Negative attitudes were most frequently associated with technology creating inconveniences, unhelpful features, as well as security and reliability concerns. Given that older adults reported more positive than negative attitudes about the technologies they use, these results contradict stereotypes that older adults are afraid or unwilling to use technology. These findings also highlight the importance of perceived benefits of use and ease of use for models of technology acceptance. Emphasizing the benefits of technology in education and training programs may increase future technology adoption. PMID:20967133

Emerging environmental technologies and environmental technology policy

NASA Astrophysics Data System (ADS)

Clarke, Leon Edward

This dissertation explores the role and design of environmental technology policy when environmental innovation is embodied in emerging environmental technologies such as photovoltaic cells or fuel cells. The dissertation consists of three individual studies, all of which use a simplified, general model industry between an emerging environmental technology and an entrenched, more-polluting technology. It clarifies the situations in which environmental technology policy can achieve high welfare and those in which it cannot; and it separates the possible situations an emerging environmental technology might face into four scenarios, each with its own technology policy recommendations. The second study attempts to clarify which of two factors is having a larger limiting effect on private investment in photovoltaics: the failure to internalize the environmental costs of fossil fuel electricity generation or a broad set of innovation market failures that apply to innovation irrespective of environmental concerns. The study indicates that innovation market failures are probably having a significantly larger impact than incomplete internalization. The third study explores the effectiveness of adoption subsidies at encouraging private-sector innovation. The conclusion is that adoption subsidies probably have only a limited effect on long-term, private-sector research. Two important general conclusions of the dissertation are (1) that optimal technology policy should begin with technology-push measures and end with demand-pull measures; and (2) that the technological response to internalization instruments, such as emissions taxes, may be highly nonlinear.

Technology Area Roadmap for In Space Propulsion Technologies

NASA Technical Reports Server (NTRS)

Johnson, Les; Meyer, Mike; Coote, David; Goebel, Dan; Palaszewski, Bryan; White, Sonny

2010-01-01

This slide presentation reviews the technology area (TA) roadmap to develop propulsion technologies that will be used to enable further exploration of the solar system, and beyond. It is hoped that development of the technologies within this TA will result in technical solutions that will improve thrust levels, specific impulse, power, specific mass, volume, system mass, system complexity, operational complexity, commonality with other spacecraft systems, manufacturability and durability. Some of the propulsion technologies that are reviewed include: chemical and non-chemical propulsion, and advanced propulsion (i.e., those with a Technology Readiness level of less than 3). Examples of these advanced technologies include: Beamed Energy, Electric Sail, Fusion, High Energy Density Materials, Antimatter, Advanced Fission and Breakthrough propulsion technologies. Timeframes for development of some of these propulsion technologies are reviewed, and top technical challenges are reviewed. This roadmap describes a portfolio of in-space propulsion technologies that can meet future space science and exploration needs.

Pulse oximeter based mobile biotelemetry application.

PubMed

Işik, Ali Hakan; Güler, Inan

2012-01-01

Quality and features of tele-homecare are improved by information and communication technologies. In this context, a pulse oximeter-based mobile biotelemetry application is developed. With this application, patients can measure own oxygen saturation and heart rate through Bluetooth pulse oximeter at home. Bluetooth virtual serial port protocol is used to send the test results from pulse oximeter to the smart phone. These data are converted into XML type and transmitted to remote web server database via smart phone. In transmission of data, GPRS, WLAN or 3G can be used. The rule based algorithm is used in the decision making process. By default, the threshold value of oxygen saturation is 80; the heart rate threshold values are 40 and 150 respectively. If the patient's heart rate is out of the threshold values or the oxygen saturation is below the threshold value, an emergency SMS is sent to the doctor. By this way, the directing of an ambulance to the patient can be performed by doctor. The doctor for different patients can change these threshold values. The conversion of the result of the evaluated data to SMS XML template is done on the web server. Another important component of the application is web-based monitoring of pulse oximeter data. The web page provides access to of all patient data, so the doctors can follow their patients and send e-mail related to the evaluation of the disease. In addition, patients can follow own data on this page. Eight patients have become part of the procedure. It is believed that developed application will facilitate pulse oximeter-based measurement from anywhere and at anytime.

Mediated Effects of Technology Competencies and Experiences on Relations among Attitudes Towards Technology Use, Technology Ownership, and Self Efficacy about Technological Pedagogical Content Knowledge

NASA Astrophysics Data System (ADS)

Yerdelen-Damar, Sevda; Boz, Yezdan; Aydın-Günbatar, Sevgi

2017-08-01

This study examined the relations of preservice science teachers' attitudes towards technology use, technology ownership, technology competencies, and experiences to their self-efficacy beliefs about technological pedagogical content knowledge (TPACK). The present study also investigated interrelations among preservice teachers' attitudes towards technology use, technology ownership, technology competencies, and experiences. The participants of study were 665 elementary preservice science teachers (467 females, 198 males) from 7 colleges in Turkey. The proposed model based on educational technology literature was tested using structural equation modeling. The model testing results revealed that preservice teachers' technology competencies and experiences mediated the relation of technology ownership to their TPACK self efficacy beliefs. The direct relation of their possession of technology to their TPACK self efficacy beliefs was insignificant while the indirect relation through their technology competencies and experiences was significant. The results also indicated there were significant direct effects of preservice teachers' attitudes towards technology use, technology competencies, and experiences on their TPACK self efficacy beliefs.

Technology transfer of remote sensing technology

NASA Technical Reports Server (NTRS)

Smith, A. D.

1980-01-01

The basic philosophy and some current activities of MSFC Technology Transfer with regard to remote sensing technology are briefly reviewed. Among the problems that may be alleviated through such technology transfer are the scarcity of energy and mineral resources, the alteration of the environment by man, unpredictable natural disasters, and the effect of unanticipated climatic change on agricultural productivity.

Science-Technology-Society or Technology-Society-Science? Insights from an Ancient Technology

ERIC Educational Resources Information Center

Lee, Yeung Chung

2010-01-01

Current approaches to science-technology-society (STS) education focus primarily on the controversial socio-scientific issues that arise from the application of science in modern technology. This paper argues for an interdisciplinary approach to STS education that embraces science, technology, history, and social and cultural studies. By employing…

Center for development technology and program in technology and human affairs. [emphasizing technology-based networks

NASA Technical Reports Server (NTRS)

Wong, M. D.

1974-01-01

The role of technology in nontraditional higher education with particular emphasis on technology-based networks is analyzed nontraditional programs, institutions, and consortia are briefly reviewed. Nontraditional programs which utilize technology are studied. Technology-based networks are surveyed and analyzed with regard to kinds of students, learning locations, technology utilization, interinstitutional relationships, cost aspects, problems, and future outlook.

Investigating the effectiveness of using Bluetooth low-energy technology to trigger in-vehicle messages in work zones : final report.

DOT National Transportation Integrated Search

2016-12-01

In order to reduce risky behavior around workzones, this project examines the effectiveness of using in-vehicle : messages to heighten drivers awareness of safety-critical and pertinent workzone information. : This investigation centers around an ...

Philosophy of Technology Assumptions in Educational Technology Leadership

ERIC Educational Resources Information Center

Webster, Mark David

2017-01-01

A qualitative study using grounded theory methods was conducted to (a) examine what philosophy of technology assumptions are present in the thinking of K-12 technology leaders, (b) investigate how the assumptions may influence technology decision making, and (c) explore whether technological determinist assumptions are present. Subjects involved…

The Model Technology School: Toward Literacy through Technology. Technology.

ERIC Educational Resources Information Center

Schneider, Raymond J.

This paper describes one Florida school's experience with the Model Technology Schools (MTS) pilot program, and proposes a poetry curriculum for K-12 education that incorporates laserdisc technology for student presentations. Webster Elementary School in St. Augustine was the smallest of five schools chosen for the MTS program to demonstrate the…

Evaluation of dynamic message signs and their potential impact on traffic flow : [research summary].

DOT National Transportation Integrated Search

2013-04-01

The objective of this research was to understand the potential impact of DMS messages on traffic : flow and evaluate their accuracy, timeliness, relevance and usefulness. Additionally, Bluetooth : sensors were used to track and analyze the diversion ...

Worm epidemics in wireless ad hoc networks

NASA Astrophysics Data System (ADS)

Nekovee, Maziar

2007-06-01

A dramatic increase in the number of computing devices with wireless communication capability has resulted in the emergence of a new class of computer worms which specifically target such devices. The most striking feature of these worms is that they do not require Internet connectivity for their propagation but can spread directly from device to device using a short-range radio communication technology, such as WiFi or Bluetooth. In this paper, we develop a new model for epidemic spreading of these worms and investigate their spreading in wireless ad hoc networks via extensive Monte Carlo simulations. Our studies show that the threshold behaviour and dynamics of worm epidemics in these networks are greatly affected by a combination of spatial and temporal correlations which characterize these networks, and are significantly different from the previously studied epidemics in the Internet.

Technology Games: Using Wittgenstein for Understanding and Evaluating Technology.

PubMed

Coeckelbergh, Mark

2017-08-15

In the philosophy of technology after the empirical turn, little attention has been paid to language and its relation to technology. In this programmatic and explorative paper, it is proposed to use the later Wittgenstein, not only to pay more attention to language use in philosophy of technology, but also to rethink technology itself-at least technology in its aspect of tool, technology-in-use. This is done by outlining a working account of Wittgenstein's view of language (as articulated mainly in the Investigations) and by then applying that account to technology-turning around Wittgenstein's metaphor of the toolbox. Using Wittgenstein's concepts of language games and form of life and coining the term 'technology games', the paper proposes and argues for a use-oriented, holistic, transcendental, social, and historical approach to technology which is empirically but also normatively sensitive, and which takes into account implicit knowledge and know-how. It gives examples of interaction with social robots to support the relevance of this project for understanding and evaluating today's technologies, makes comparisons with authors in philosophy of technology such as Winner and Ihde, and sketches the contours of a phenomenology and hermeneutics of technology use that may help us to understand but also to gain a more critical relation to specific uses of concrete technologies in everyday contexts. Ultimately, given the holism argued for, it also promises a more critical relation to the games and forms of life technologies are embedded in-to the ways we do things.

Subjective Technology Adaptivity Predicts Technology Use in Old Age.

PubMed

Kamin, Stefan T; Lang, Frieder R; Beyer, Anja

2017-01-01

To date, not much is known about the psychological and motivational factors underlying technology use in late life. What are the interindividual determinants that lead older adults to invest in using technological innovations despite the age-related physiological changes that impose challenges on behavioral plasticity in everyday life? This research explores interindividual differences in subjective technology adaptivity - a general technology-related motivational resource that accounts for technology use in late life. More specifically, we investigate the influence of this factor relative to demographic characteristics, personality traits, and functional limitations in a longitudinal sample of community-dwelling older adults. We report results from a paper-and-pencil survey with 136 older adults between 59 and 92 years of age (mean = 71.4, SD = 7.4). Of those participants, 77 participated in a 2-year follow-up. We assessed self-reports of technology use, subjective technology adaptivity, functional limitations, and the personality traits openness to new experiences and neuroticism. Higher levels of subjective technology adaptivity were associated with technology use at the first measurement as well as increased use over the course of 2 years. Subjective technology adaptivity is a significant predictor of technology use in old age. Our findings contribute to improving the understanding of interindividual differences when using technological innovation in late life. Moreover, our findings have implications in the context of user involvement and may contribute to the successful development of innovative technology for older adults. © 2017 S. Karger AG, Basel.

Technology assessment or technology harassment: The attacks on science and technology

NASA Technical Reports Server (NTRS)

Green, L., Jr.

1972-01-01

The manner in which technology is being assessed by various groups and individuals is discussed. Attacks on science and technology (specifically military uses and funding), and the disillusionment of the public with the lack of relevance of science to the public interest and with the infallible wisdom of scientists are described. The effects of the fear of environmental pollution are emphasized. It is concluded that the important issues of science, technology, and public policy will require a pluralistic definition of the public interest by open adversary proceedings. It is also felt that the danger is not that new technology will receive inadequate assessment for possible deleterious secondary effects, but that harassment by an overemotional political process may prevent its coming to fruition.

Technology coordination

NASA Technical Reports Server (NTRS)

Hartman, Steven

1992-01-01

Viewgraphs on technology coordination are provided. Topics covered include: technology coordination process to date; goals; how the Office of Aeronautics and Space Technology (OAST) can support the Office of Space Science and Applications (OSSA); how OSSA can support OAST; steps to technology transfer; and recommendations.

Wireless data collection system for real-time arterial travel time estimates.

DOT National Transportation Integrated Search

2011-03-01

This project pursued several objectives conducive to the implementation and testing of a Bluetooth (BT) based system to collect travel time data, including the deployment of a BT-based travel time data collection system to perform comprehensive testi...

Guerilla Technology.

ERIC Educational Resources Information Center

Van Horn, Royal

1999-01-01

Staff at disadvantaged schools lacking sufficient technology must take matters into their own hands. Guerilla technology tactics include finding all the hidden technology on campus, scanning the school budget carefully, helping others spend their technology money, and scrounging free computers at universities and local businesses. (MLH)

Classical Mechanics Experiments using Wiimotes

NASA Astrophysics Data System (ADS)

Lopez, Alexander; Ochoa, Romulo

2010-02-01

The Wii, a video game console, is a very popular device. Although computationally it is not a powerful machine by today's standards, to a physics educator the controllers are its most important components. The Wiimote (or remote) controller contains a three-axis accelerometer, an infrared detector, and Bluetooth connectivity at a relatively low price. Thanks to available open source code, such as GlovePie, any PC or Laptop with Bluetooth capability can detect the information sent out by the Wiimote. We present experiments that use two or three Wiimotes simultaneously to measure the variable accelerations in two mass systems interacting via springs. Normal modes are determined from the data obtained. Masses and spring constants are varied to analyze their impact on the accelerations of the systems. We present the results of our experiments and compare them with those predicted using Lagrangian mechanics. )

FY04 Engineering Technology Reports Technology Base

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharpe, R M

2005-01-27

Lawrence Livermore National Laboratory's Engineering Directorate has two primary discretionary avenues for its investment in technologies: the Laboratory Directed Research and Development (LDRD) program and the ''Tech Base'' program. This volume summarizes progress on the projects funded for technology-base efforts in FY2004. The Engineering Technical Reports exemplify Engineering's more than 50-year history of researching and developing (LDRD), and reducing to practice (technology-base) the engineering technologies needed to support the Laboratory's missions. Engineering has been a partner in every major program and project at the Laboratory throughout its existence, and has prepared for this role with a skilled workforce and technicalmore » resources. This accomplishment is well summarized by Engineering's mission: ''Enable program success today and ensure the Laboratory's vitality tomorrow''. LDRD is the vehicle for creating those technologies and competencies that are cutting edge. These require a significant level of research or contain some unknown that needs to be fully understood. Tech Base is used to apply those technologies, or adapt them to a Laboratory need. The term commonly used for Tech Base projects is ''reduction to practice''. Tech Base projects effect the natural transition to reduction-to-practice of scientific or engineering methods that are well understood and established. They represent discipline-oriented, core competency activities that are multi-programmatic in application, nature, and scope. The objectives of technology-base funding include: (1) the development and enhancement of tools and processes to provide Engineering support capability, such as code maintenance and improved fabrication methods; (2) support of Engineering science and technology infrastructure, such as the installation or integration of a new capability; (3) support for technical and administrative leadership through our technology Centers; and (4) the initial

Technology in the Classroom: Teachers and Technology--A Technological Divide

ERIC Educational Resources Information Center

Clarke, Gregory, Sr.; Zagarell, Jesse

2012-01-01

The education system in the United States continues to grapple with adapting to change, especially when it comes to integrating technology in the curriculum. The United States needs to use its resources to stay competitive in the increasingly technological world, particularly in the classroom. Lefebvre, Deaudelin, and Loiselle (2006) posit that…

Educational technologies in health sciences libraries: teaching technology skills.

PubMed

Hurst, Emily J

2014-01-01

As technology rapidly changes, libraries remain go-to points for education and technology skill development. In academic health sciences libraries, trends suggest librarians provide more training on technology topics than ever before. While education and training have always been roles for librarians, providing technology training on new mobile devices and emerging systems requires class creation and training capabilities that are new to many librarians. To appeal to their users, many health sciences librarians are interested in developing technology-based classes. This column explores the question: what skills are necessary for developing and teaching technology in an academic health sciences library setting?

Educational Technologies in Health Science Libraries: Teaching Technology Skills

PubMed Central

Hurst, Emily J.

2014-01-01

As technology rapidly changes, libraries remain go-to points for education and technology skill development. In academic health sciences libraries, trends suggest librarians provide more training on technology topics than ever before. While education and training have always been roles for librarians, providing technology training on new mobile devices and emerging systems requires class creation and training capabilities that are new to many. To appeal to their users, many health sciences librarians are interested in developing technology-based classes. This column explores the question: what skills are necessary for developing and teaching technology in an academic health sciences library setting? PMID:24528269

Drahtlose Audioübertragung

NASA Astrophysics Data System (ADS)

Niehoff, Wolfgang

Für die drahtlose Übertragung von Audiosignalen werden elektromagnetische Wellen als Trägersignale genutzt. Auch der Rundfunk bedient sich dieser Wellen auf unterschiedlichen Frequenzen, ebenso Kommunikationsdienste wie der Mobilfunk, WLAN, Bluetooth und andere Funkdienste (Abb. 19.1).

Technology Transfer Issues and a New Technology Transfer Model

ERIC Educational Resources Information Center

Choi, Hee Jun

2009-01-01

The following are major issues that should be considered for efficient and effective technology transfer: conceptions of technology, technological activity and transfer, communication channels, factors affecting transfer, and models of transfer. In particular, a well-developed model of technology transfer could be used as a framework for…

Technological Literacy Education and Technological and Vocational Education in Taiwan

ERIC Educational Resources Information Center

Lee, Lung-Sheng Steven

2010-01-01

Technology education in Taiwan is categorized into the following two types: (1) technological literacy education (TLE)--the education for all people to become technological literates; and (2) technological specialty education (TSE)--the education for specific people to become technicians and professionals for technology-related jobs. This paper…

Changing Technology and Work: Northern Telecom. CAW Technology Project.

ERIC Educational Resources Information Center

Robertson, David; Wareham, Jeff

A project to examine the implications of technological change at Northern Telecom consisted of two major components: a technological survey and case study research. A questionnaire that contained more than 90 questions on technological change was distributed through local union technology committee meetings in Brampton, London, Belleville, and…

Laser Technology.

ERIC Educational Resources Information Center

Gauger, Robert

1993-01-01

Describes lasers and indicates that learning about laser technology and creating laser technology activities are among the teacher enhancement processes needed to strengthen technology education. (JOW)

Projecting technology change to improve space technology planning and systems management

NASA Astrophysics Data System (ADS)

Walk, Steven Robert

2011-04-01

Projecting technology performance evolution has been improving over the years. Reliable quantitative forecasting methods have been developed that project the growth, diffusion, and performance of technology in time, including projecting technology substitutions, saturation levels, and performance improvements. These forecasts can be applied at the early stages of space technology planning to better predict available future technology performance, assure the successful selection of technology, and improve technology systems management strategy. Often what is published as a technology forecast is simply scenario planning, usually made by extrapolating current trends into the future, with perhaps some subjective insight added. Typically, the accuracy of such predictions falls rapidly with distance in time. Quantitative technology forecasting (QTF), on the other hand, includes the study of historic data to identify one of or a combination of several recognized universal technology diffusion or substitution patterns. In the same manner that quantitative models of physical phenomena provide excellent predictions of system behavior, so do QTF models provide reliable technological performance trajectories. In practice, a quantitative technology forecast is completed to ascertain with confidence when the projected performance of a technology or system of technologies will occur. Such projections provide reliable time-referenced information when considering cost and performance trade-offs in maintaining, replacing, or migrating a technology, component, or system. This paper introduces various quantitative technology forecasting techniques and illustrates their practical application in space technology and technology systems management.

Making the Connection: Technological Literacy and Technology Assessment.

ERIC Educational Resources Information Center

Deal, Walter F.

2002-01-01

Technology assessment is the process of identifying, analyzing, and evaluating potential consequences of technology. Tools for assessing and forecasting impact include relevance trees and futures wheels. Activities based on these tools can be used to teach assessment to technology education students. (SK)

Assessment of US industry's technology trends and new technology requirements

NASA Technical Reports Server (NTRS)

1984-01-01

The utility and effectiveness of a novel approach (the Applications Development, or AD approach), intended to augment the efficiency of NASA's technology utilization (TU) through dissemination of NASA technologies and joint technology development efforts with U.S. industry is tested. The innovative AD approach consists of the following key elements: selection of NASA technologies appearing to have leading edge attributes; interaction with NASA researchers to assess the characteristics and quality of each selected technology; identification of industry's needs in the selected technology areas; structuring the selected technologies in terms of specifications and standards familiar to industry (industrial Spec. Sheets); identification and assessment of industry's interest in the specific selected NASA technologies, utilizing the greatly facilitated communication made possible by the availability of the industrial Spec. Sheets; and matching selected NASA technologies with the needs of selected industries.

Human spaceflight technology needs-a foundation for JSC's technology strategy

NASA Astrophysics Data System (ADS)

Stecklein, J. M.

Human space exploration has always been heavily influenced by goals to achieve a specific mission on a specific schedule. This approach drove rapid technology development, the rapidity of which added risks and became a major driver for costs and cost uncertainty. The National Aeronautics and Space Administration (NASA) is now approaching the extension of human presence throughout the solar system by balancing a proactive yet less schedule-driven development of technology with opportunistic scheduling of missions as the needed technologies are realized. This approach should provide cost effective, low risk technology development that will enable efficient and effective manned spaceflight missions. As a first step, the NASA Human Spaceflight Architecture Team (HAT) has identified a suite of critical technologies needed to support future manned missions across a range of destinations, including in cis-lunar space, near earth asteroid visits, lunar exploration, Mars moons, and Mars exploration. The challenge now is to develop a strategy and plan for technology development that efficiently enables these missions over a reasonable time period, without increasing technology development costs unnecessarily due to schedule pressure, and subsequently mitigating development and mission risks. NASA's Johnson Space Center (JSC), as the nation's primary center for human exploration, is addressing this challenge through an innovative approach in allocating Internal Research and Development funding to projects. The HAT Technology Needs (Tech Needs) Database has been developed to correlate across critical technologies and the NASA Office of Chief Technologist Technology Area Breakdown Structure (TABS). The TechNeeds Database illuminates that many critical technologies may support a single technical capability gap, that many HAT technology needs may map to a single TABS technology discipline, and that a single HAT technology need may map to multiple TABS technology disciplines. Th

Human Spaceflight Technology Needs - A Foundation for JSC's Technology Strategy

NASA Technical Reports Server (NTRS)

Stecklein, Jonette M.

2013-01-01

Human space exploration has always been heavily influenced by goals to achieve a specific mission on a specific schedule. This approach drove rapid technology development, the rapidity of which adds risks as well as provides a major driver for costs and cost uncertainty. The National Aeronautics and Space Administration (NASA) is now approaching the extension of human presence throughout the solar system by balancing a proactive yet less schedule-driven development of technology with opportunistic scheduling of missions as the needed technologies are realized. This approach should provide cost effective, low risk technology development that will enable efficient and effective manned spaceflight missions. As a first step, the NASA Human Spaceflight Architecture Team (HAT) has identified a suite of critical technologies needed to support future manned missions across a range of destinations, including in cis-lunar space, near earth asteroid visits, lunar exploration, Mars moons, and Mars exploration. The challenge now is to develop a strategy and plan for technology development that efficiently enables these missions over a reasonable time period, without increasing technology development costs unnecessarily due to schedule pressure, and subsequently mitigating development and mission risks. NASA's Johnson Space Center (JSC), as the nation s primary center for human exploration, is addressing this challenge through an innovative approach in allocating Internal Research and Development funding to projects. The HAT Technology Needs (TechNeeds) Database has been developed to correlate across critical technologies and the NASA Office of Chief Technologist Technology Area Breakdown Structure (TABS). The TechNeeds Database illuminates that many critical technologies may support a single technical capability gap, that many HAT technology needs may map to a single TABS technology discipline, and that a single HAT technology need may map to multiple TABS technology

Technology transfer methodology

NASA Technical Reports Server (NTRS)

Labotz, Rich

1991-01-01

Information on technology transfer methodology is given in viewgraph form. Topics covered include problems in economics, technology drivers, inhibitors to using improved technology in development, technology application opportunities, and co-sponsorship of technology.

Examining Engineering & Technology Students' Acceptance of Network Virtualization Technology Using the Technology Acceptance Model

ERIC Educational Resources Information Center

Yousif, Wael K.

2010-01-01

This causal and correlational study was designed to extend the Technology Acceptance Model (TAM) and to test its applicability to Valencia Community College (VCC) Engineering and Technology students as the target user group when investigating the factors influencing their decision to adopt and to utilize VMware as the target technology. In…

OAST space research and technology applications: Technology transfer successes

NASA Technical Reports Server (NTRS)

Reck, Gregory M.

1992-01-01

The ultimate measure of success in the Space Research and Technology Program is the incorporation of a technology into an operational mission. Charts are presented that describe technology products which OAST has helped support that (1) have been used in a space mission, (2) have been incorporated into the baseline design of a flight system in the development phase, or (3) have been picked up by a commercial or other non-NASA user. We hope that these examples will demonstrate the value of investment in technology. Pictured on the charts are illustrations of the technology product, the mission or user which has incorporated the technology, and where appropriate, results from the mission itself.

The Technological Dimension of Educational Technology in Europe

ERIC Educational Resources Information Center

Dimitriadis, Yannis

2012-01-01

This article describes some of the main technological trends and issues of the European landscape of research and innovation in educational technology. Although several innovative technologies (tools, architectures, platforms, or approaches) emerge, such as intelligent support to personalization, collaboration or adaptation in mobile, game-based,…

Science and Technology Test Mining: Disruptive Technology Roadmaps

DTIC Science & Technology

2003-07-23

integrating breakthrough technologies to maintain the U.S.’s technological advantage and the role of naval engineers in fostering and managing innovation . It...highlights these. Loutfy, R, Belkhir, L, Managing innovation at Xerox, RESEARCH-TECHNOLOGY MANAGEMENT, 44:4, July-Aug 2001. The careful and painstaking

CHP Technologies

EPA Pesticide Factsheets

Learn about CHP technologies, including reciprocating engines, combustion turbines, steam turbines, microturbines, fuel cells, and waste heat to power. Access the Catalog of CHP Technologies and the Biomass CHP Catalog of Technologies.

Introducing Current Technologies

NASA Technical Reports Server (NTRS)

Mitchell, Tiffany

1995-01-01

The objective of the study was a continuation of the 'technology push' activities that the Technology Transfer Team conducts at this time. It was my responsibility to research current technologies at Langley Research Center and find a commercial market for these technologies in the private industry. After locating a market for the technologies, a mailing package was put together which informed the companies of the benefits of NASA Langley's technologies. The mailing package included articles written about the technology, patent material, abstracts from technical papers, and one-pagers which were used at the Technology Opportunities Showcase (TOPS) exhibitions. The companies were encouraged to consult key team members for further information on the technologies.

Idea Technology and Product Technology: Seeing beyond the Text to the Technology That Works

ERIC Educational Resources Information Center

Bednar, Maryanne R.

2004-01-01

Sifting through the myriad "idea" technologies (such as multiple intelligence theories or Piaget's Theory of Cognitive Development) and "product" technologies (such as PowerPoint or digital cameras) can be overwhelming, but Bednar persuades us that it's not about having the most recent technology, it's about using what works for "your" students in…

Mediated Effects of Technology Competencies and Experiences on Relations among Attitudes towards Technology Use, Technology Ownership, and Self Efficacy about Technological Pedagogical Content Knowledge

ERIC Educational Resources Information Center

Yerdelen-Damar, Sevda; Boz, Yezdan; Aydin-Günbatar, Sevgi

2017-01-01

This study examined the relations of preservice science teachers' attitudes towards technology use, technology ownership, technology competencies, and experiences to their self-efficacy beliefs about technological pedagogical content knowledge (TPACK). The present study also investigated interrelations among preservice teachers' attitudes towards…

Advanced Technology Lifecycle Analysis System (ATLAS) Technology Tool Box (TTB)

NASA Technical Reports Server (NTRS)

Doyle, Monica; ONeil, Daniel A.; Christensen, Carissa B.

2005-01-01

The Advanced Technology Lifecycle Analysis System (ATLAS) is a decision support tool designed to aid program managers and strategic planners in determining how to invest technology research and development dollars. It is an Excel-based modeling package that allows a user to build complex space architectures and evaluate the impact of various technology choices. ATLAS contains system models, cost and operations models, a campaign timeline and a centralized technology database. Technology data for all system models is drawn from a common database, the ATLAS Technology Tool Box (TTB). The TTB provides a comprehensive, architecture-independent technology database that is keyed to current and future timeframes.

NASA Technology Applications Team: Commercial applications of aerospace technology

NASA Technical Reports Server (NTRS)

1994-01-01

The Research Triangle Institute (RTI) Team has maintained its focus on helping NASA establish partnerships with U.S. industry for dual use development and technology commercialization. Our emphasis has been on outcomes, such as licenses, industry partnerships and commercialization of technologies, that are important to NASA in its mission of contributing to the improved competitive position of U.S. industry. The RTI Team has been successful in the development of NASA/industry partnerships and commercialization of NASA technologies. RTI ongoing commitment to quality and customer responsiveness has driven our staff to continuously improve our technology transfer methodologies to meet NASA's requirements. For example, RTI has emphasized the following areas: (1) Methodology For Technology Assessment and Marketing: RTI has developed and implemented effective processes for assessing the commercial potential of NASA technologies. These processes resulted from an RTI study of best practices, hands-on experience, and extensive interaction with the NASA Field Centers to adapt to their specific needs. (2) Effective Marketing Strategies: RTI surveyed industry technology managers to determine effective marketing tools and strategies. The Technology Opportunity Announcement format and content were developed as a result of this industry input. For technologies with a dynamic visual impact, RTI has developed a stand-alone demonstration diskette that was successful in developing industry interest in licensing the technology. And (3) Responsiveness to NASA Requirements: RTI listened to our customer (NASA) and designed our processes to conform with the internal procedures and resources at each NASA Field Center and the direction provided by NASA's Agenda for Change. This report covers the activities of the Research Triangle Institute Technology Applications Team for the period 1 October 1993 through 31 December 1994.

Design and Practical Evaluation of a Family of Lightweight Protocols for Heterogeneous Sensing through BLE Beacons in IoT Telemetry Applications.

PubMed

Hernández-Rojas, Dixys L; Fernández-Caramés, Tiago M; Fraga-Lamas, Paula; Escudero, Carlos J

2017-12-27

The Internet of Things (IoT) involves a wide variety of heterogeneous technologies and resource-constrained devices that interact with each other. Due to such constraints, IoT devices usually require lightweight protocols that optimize the use of resources and energy consumption. Among the different commercial IoT devices, Bluetooth and Bluetooth Low Energy (BLE)-based beacons, which broadcast periodically certain data packets to notify their presence, have experienced a remarkable growth, specially due to their application in indoor positioning systems. This article proposes a family of protocols named Lightweight Protocol for Sensors (LP4S) that provides fast responses and enables plug-and-play mechanisms that allow IoT telemetry systems to discover new nodes and to describe and auto-register the sensors and actuators connected to a beacon. Thus, three protocols are defined depending on the beacon hardware characteristics: LP4S-6 (for resource-constraint beacons), LP4S-X (for more powerful beacons) and LP4S-J (for beacons able to run complex firmware). In order to demonstrate the capabilities of the designed protocols, the most restrictive (LP4S-6) is tested after implementing it for a telemetry application in a beacon based on Eddystone (Google's open beacon format). Thus, the beacon specification is extended in order to increase its ability to manage unlimited sensors in a telemetry system without interfering in its normal operation with Eddystone frames. The performed experiments show the feasibility of the proposed solution and its superiority, in terms of latency and energy consumption, with respect to approaches based on Generic Attribute Profile (GATT) when multiple users connect to a mote or in scenarios where latency is not a restriction, but where low-energy consumption is essential.

Design and Practical Evaluation of a Family of Lightweight Protocols for Heterogeneous Sensing through BLE Beacons in IoT Telemetry Applications

PubMed Central

2017-01-01

The Internet of Things (IoT) involves a wide variety of heterogeneous technologies and resource-constrained devices that interact with each other. Due to such constraints, IoT devices usually require lightweight protocols that optimize the use of resources and energy consumption. Among the different commercial IoT devices, Bluetooth and Bluetooth Low Energy (BLE)-based beacons, which broadcast periodically certain data packets to notify their presence, have experienced a remarkable growth, specially due to their application in indoor positioning systems. This article proposes a family of protocols named Lightweight Protocol for Sensors (LP4S) that provides fast responses and enables plug-and-play mechanisms that allow IoT telemetry systems to discover new nodes and to describe and auto-register the sensors and actuators connected to a beacon. Thus, three protocols are defined depending on the beacon hardware characteristics: LP4S-6 (for resource-constraint beacons), LP4S-X (for more powerful beacons) and LP4S-J (for beacons able to run complex firmware). In order to demonstrate the capabilities of the designed protocols, the most restrictive (LP4S-6) is tested after implementing it for a telemetry application in a beacon based on Eddystone (Google’s open beacon format). Thus, the beacon specification is extended in order to increase its ability to manage unlimited sensors in a telemetry system without interfering in its normal operation with Eddystone frames. The performed experiments show the feasibility of the proposed solution and its superiority, in terms of latency and energy consumption, with respect to approaches based on Generic Attribute Profile (GATT) when multiple users connect to a mote or in scenarios where latency is not a restriction, but where low-energy consumption is essential. PMID:29280975

Chemistry for Energy Technology I. Energy Technology Series.

ERIC Educational Resources Information Center

Center for Occupational Research and Development, Inc., Waco, TX.

This course in chemistry for energy technology is one of 16 courses in the Energy Technology Series developed for an Energy Conservation-and-Use Technology curriculum. Intended for use in two-year postsecondary technical institutions to prepare technicians for employment, the courses are also useful in industry for updating employees in…

Chemistry for Energy Technology II. Energy Technology Series.

ERIC Educational Resources Information Center

Center for Occupational Research and Development, Inc., Waco, TX.

This course in chemistry for energy technology is one of 16 courses in the Energy Technology Series developed for an Energy Conservation-and-Use Technology curriculum. Intended for use in two-year postsecondary technical institutions to prepare technicians for employment, the courses are also useful in industry for updating employees in…

Commercialization of Advanced Communications Technology Satellite (ACTS) technology

NASA Astrophysics Data System (ADS)

Plecity, Mark S.; Strickler, Walter M.; Bauer, Robert A.

1996-03-01

In an on-going effort to maintain United States leadership in communication satellite technology, the National Aeronautics and Space Administration (NASA), led the development of the Advanced Communications Technology Satellite (ACTS). NASA's ACTS program provides industry, academia, and government agencies the opportunity to perform both technology and telecommunication service experiments with a leading-edge communication satellite system. Over 80 organizations are using ACTS as a multi server test bed to establish communication technologies and services of the future. ACTS was designed to provide demand assigned multiple access (DAMA) digital communications with a minimum switchable circuit bandwidth of 64 Kbps, and a maximum channel bandwidth of 900 MHZ. It can, therefore, provide service to thin routes as well as connect fiber backbones in supercomputer networks, across oceans, or restore full communications in the event of national or manmade disaster. Service can also be provided to terrestrial and airborne mobile users. Commercial applications of ACTS technologies include: telemedicine; distance education; Department of Defense operations; mobile communications, aeronautical applications, terrestrial applications, and disaster recovery. This paper briefly describes the ACTS system and the enabling technologies employed by ACTS including Ka-band hopping spot beams, on-board routing and switching, and rain fade compensation. When used in conjunction with a time division multiple access (TDMA) architecture, these technologies provide a higher capacity, lower cost satellite system. Furthermore, examples of completed user experiments, future experiments, and plans of organizations to commercialize ACTS technology in their own future offerings will be discussed.

Trends in Health Information Technology Safety: From Technology-Induced Errors to Current Approaches for Ensuring Technology Safety

PubMed Central

2013-01-01

Objectives Health information technology (HIT) research findings suggested that new healthcare technologies could reduce some types of medical errors while at the same time introducing classes of medical errors (i.e., technology-induced errors). Technology-induced errors have their origins in HIT, and/or HIT contribute to their occurrence. The objective of this paper is to review current trends in the published literature on HIT safety. Methods A review and synthesis of the medical and life sciences literature focusing on the area of technology-induced error was conducted. Results There were four main trends in the literature on technology-induced error. The following areas were addressed in the literature: definitions of technology-induced errors; models, frameworks and evidence for understanding how technology-induced errors occur; a discussion of monitoring; and methods for preventing and learning about technology-induced errors. Conclusions The literature focusing on technology-induced errors continues to grow. Research has focused on the defining what an error is, models and frameworks used to understand these new types of errors, monitoring of such errors and methods that can be used to prevent these errors. More research will be needed to better understand and mitigate these types of errors. PMID:23882411

Smart blood pressure holter.

PubMed

İlhan, İlhan

2018-03-01

In this study, a wireless blood pressure holter that can be used with smart mobile devices was developed. The developed blood pressure holter consists of two parts, which are a smart mobile device and a cuff. The smart mobile device is used as a recording, control and display device through a developed interface, while the cuff was designed to take measurements from the arm. Resistor-Capacitor (RC) and digital filters were used on the cuff that communicates with the smart mobile device via Bluetooth. The blood pressure was estimated using the Simple Hill Climbing Algorithm (HCA). It is possible to measure instantaneous or programmable blood pressure and heart rate values at certain intervals using this holter. The test was conducted with 30 individuals at different ages with the guidance of a specialist health personnel. The results showed that an accuracy at 93.89% and 91.95% rates could be obtained for systolic and diastolic pressure values, respectively, when compared with those obtained using a traditional sphygmomanometer. The accuracy level for the heart rate was measured as 97.66%. Furthermore, this device was tested day and night in the holter mode in terms of working time, the continuity of the Bluetooth connection and the reliability of the measurement results. The test results were evaluated separately in terms of measurement accuracy, working time, the continuity of the Bluetooth connection and the reliability of the measurement results. The measurement accuracy for systolic, diastolic blood pressure and heart rate values was obtained as 93.89%, 91.95% and 97.66%, respectively. The maximum number of measurements which can be conducted with four 1000 mA alkaline batteries at 20 min intervals was found approximately 79 (little more than 24 h). In addition, it was determined that the continuity of the Bluetooth connection and the reliability of the measurement results were automatically achieved through the features in the interface developed for the

The effect of electromagnetic interference from mobile communication on the performance of intensive care ventilators.

PubMed

Jones, R P; Conway, D H

2005-08-01

Electromagnetic interference produced by wireless communication can affect medical devices and hospital policies exist to address this risk. During the transfer of ventilated patients, these policies may be compromised by essential communication between base and receiving hospitals. Local wireless networks (e.g. Bluetooth) may reduce the 'spaghetti syndrome' of wires and cables seen on intensive care units, but also generate electromagnetic interference. The aim of this study was to investigate these effects on displayed and actual ventilator performance. Five ventilators were tested: Drager Oxylog 2000, BREAS LTV-1000, Respironics BiPAP VISION, Puritan Bennett 7200 and 840. Electromagnetic interference was generated by three devices: Simoco 8020 radio handset, Nokia 7210 and Nokia 6230 mobile phone, Nokia 6230 communicating via Bluetooth with a Palm Tungsten T Personal Digital Assistant. We followed the American National Standard Recommended Practice for On-Site, Ad Hoc Testing (ANSI C63) for electromagnetic interference. We used a ventilator tester, to simulate healthy adult lungs and measure ventilator performance. The communication device under test was moved in towards each ventilator from a distance of 1 m in six axes. Alarms or error codes on the ventilator were recorded, as was ventilator performance. All ventilators tested, except for the Respironics VISION, showed a display error when subjected to electromagnetic interference from the Nokia phones and Simoco radio. Ventilator performance was only affected by the radio which caused the Puritan Bennett 840 to stop functioning completely. The transfer ventilators' performance were not affected by radio or mobile phone, although the mobile phone did trigger a low-power alarm. Effects on intensive care ventilators included display reset, with the ventilator restoring normal display function within 2 s, and low-power/low-pressure alarms. Bluetooth transmission had no effect on the function of all the

Robotics-Control Technology. Technology Learning Activity. Teacher Edition. Technology Education Series.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This document contains the materials required for presenting an 8-day competency-based technology learning activity (TLA) designed to introduce students in grades 6-10 to advances and career opportunities in the field of robotics-control technology. The guide uses hands-on exploratory experiences into which activities to help students develop…

NASA Technology Applications Team: Commercial applications of aerospace technology

NASA Technical Reports Server (NTRS)

1994-01-01

The Research Triangle Institute (RTI) is pleased to report the results of NASA contract NASW-4367, 'Operation of a Technology Applications Team'. Through a period of significant change within NASA, the RTI Team has maintained its focus on helping NASA establish partnerships with U.S. industry for dual use development and technology commercialization. Our emphasis has been on outcomes, such as licenses, industry partnerships and commercialization of technologies that are important to NASA in its mission of contributing to the improved competitive position of U.S. industry. RTI's ongoing commitment to quality and customer responsiveness has driven our staff to continuously improve our technology transfer methodologies to meet NASA's requirements. For example, RTI has emphasized the following areas: (1) Methodology For Technology Assessment and Marketing: RTI has developed an implemented effective processes for assessing the commercial potential of NASA technologies. These processes resulted from an RTI study of best practices, hands-on experience, and extensive interaction with the NASA Field Centers to adapt to their specific needs; (2) Effective Marketing Strategies: RTI surveyed industry technology managers to determine effective marketing tools and strategies. The Technology Opportunity Announcement format and content were developed as a result of this industry input. For technologies with a dynamic visual impact, RTI has developed a stand-alone demonstration diskette that was successful in developing industry interest in licensing the technology; and (3) Responsiveness to NASA Requirements: RTI listened to our customer (NASA) and designed our processes to conform with the internal procedures and resources at each NASA Field Center and the direction provided by NASA's Agenda for Change. This report covers the activities of the Research Triangle Institute Technology Applications Team for the period 1 October 1993 through 31 December 1994.

Technology Transfer Report

NASA Technical Reports Server (NTRS)

2000-01-01

Since its inception, Goddard has pursued a commitment to technology transfer and commercialization. For every space technology developed, Goddard strives to identify secondary applications. Goddard then provides the technologies, as well as NASA expertise and facilities, to U.S. companies, universities, and government agencies. These efforts are based in Goddard's Technology Commercialization Office. This report presents new technologies, commercialization success stories, and other Technology Commercialization Office activities in 1999.

Utilizing a Homecare Platform for Remote Monitoring of Patients with Idiopathic Pulmonary Fibrosis.

PubMed

Panagopoulos, Christos; Malli, Foteini; Menychtas, Andreas; Smyrli, Efstathia-Petrina; Georgountzou, Aikaterini; Daniil, Zoe; Gourgoulianis, Konstantinos I; Tsanakas, Panayiotis; Maglogiannis, Ilias

2017-01-01

Homecare and home telemonitoring are a focal point of emerging healthcare schemes, with proven benefits for both patients, caregivers and providers, including reduction of healthcare costs and improved patients' quality of life, especially in the case of chronic disease management. Studies have evaluated solutions for remote monitoring of chronic patients based on technologies that allow daily symptom and vital signs monitoring, tailored to the needs of specific diseases. In this work, we present an affordable home telemonitoring system for patients with idiopathic pulmonary fibrosis (IPF), based on an application for mobile devices and Bluetooth-enabled sensors for pulse oximetry and blood pressure measurements. Besides monitoring of vital signs, the system incorporates communication via videoconferencing and emergency response, with support from a helpdesk service. A pilot study was conducted, in order to verify the proposed solution's feasibility. The results support the utilization of the system for effective monitoring of patients with IPF.

Technology transfer

NASA Technical Reports Server (NTRS)

Penaranda, Frank E.

1992-01-01

The topics are presented in viewgraph form and include the following: international comparison of R&D expenditures in 1989; NASA Technology Transfer Program; NASA Technology Utilization Program thrusts for FY 1992 and FY 1993; National Technology Transfer Network; and NTTC roles.

Managing Technology Resourcefully: Part I--Technology and Instruction

ERIC Educational Resources Information Center

Weeks, Richard

2009-01-01

The transformative powers of digital technology to improve student learning and the resulting effect of that technology to make the business of education more cost-effective are two of the more exciting dynamics in schooling today. Before the current school year ends, new products and upgrades will be available to replace much of the technology.…

Incorporating Experimental Technologies in the Middle Level Technology Education Classroom

ERIC Educational Resources Information Center

Shields, C. J.; Rogers, George E.

2005-01-01

This paper offers some concrete ideas and suggestions for incorporating discussions of experimental technologies in the middle level technology education classroom. Technology education students should be aware of experimental technologies. They should understand the ramifications of items such as hybrid vehicles, photovoltaic solar panels,…

Introductory Physics Experiments Using the Wii Balance Board

NASA Astrophysics Data System (ADS)

Starr, Julian; Sobczak, Robert; Iqbal, Zohaib; Ochoa, Romulo

2010-02-01

The Wii, a video game console by Nintendo, utilizes several different controllers, such as the Wii remote (Wiimote) and the balance board, for game-playing. The balance board was introduced in early 2008. It contains four strain gauges and has Bluetooth connectivity at a relatively low price. Thanks to available open source code, such as GlovePie, any PC with Bluetooth capability can detect the information sent out by the balance board. Based on the ease with which the forces measured by each strain gauge can be obtained, we have designed several experiments for introductory physics courses that make use of this device. We present experiments to measure the forces generated when students lift their arms with and without added weights, distribution of forces on an extended object when weights are repositioned, and other normal forces cases. The results of our experiments are compared with those predicted by Newtonian mechanics. )

Contemporary Technology.

ERIC Educational Resources Information Center

Clark, Gilbert, Ed.

1999-01-01

This theme issue of "InSEA News" focuses on contemporary technology and art education. The articles are: "International Travel and Contemporary Technology" (Gilbert Clark); "Recollections and Visions for Electronic Computing in Art Education" (Guy Hubbard); "Using Technologies in Art Education: A Review of…

Electro-Technologies. Guide to Standards and Implementation. Career & Technology Studies.

ERIC Educational Resources Information Center

Alberta Dept. of Education, Edmonton. Curriculum Standards Branch.

With this Career and Technologies Studies (CTS) curriculum guide, secondary students in Alberta can do the following: develop skills that can be applied in their daily lives; refine career-planning skills; develop technology-related skills in electro-technologies; enhance employability skills, especially in electro-technologies industries; and…

Industrial Arts Test Development, Book III. Resource Items for Graphics Technology, Power Technology, Production Technology.

ERIC Educational Resources Information Center

New York State Education Dept., Albany.

This booklet is designed to assist teachers in developing examinations for classroom use. It is a collection of 955 objective test questions, mostly multiple choice, for industrial arts students in the three areas of graphics technology, power technology, and production technology. Scoring keys are provided. There are no copyright restrictions,…

RESLanjut: The learning media for improve students understanding in embedded systems

NASA Astrophysics Data System (ADS)

Indrianto, Susanti, Meilia Nur Indah; Karina, Djunaidi

2017-08-01

The use of network in embedded system can be done with many kinds of network, with the use of mobile phones, bluetooths, modems, ethernet cards, wireless technology and so on. Using network in embedded system could help people to do remote controlling. On previous research, researchers found that many students have the ability to comprehend the basic concept of embedded system. They could also make embedded system tools but without network integration. And for that, a development is needed for the embedded system module. The embedded system practicum module design needs a prototype method in order to achieve the desired goal. The prototype method is often used in the real world. Or even, a prototype method is a part of products that consist of logic expression or external physical interface. The embedded system practicum module is meant to increase student comprehension of embedded system course, and also to encourage students to innovate on technology based tools. It is also meant to help teachers to teach the embedded system concept on the course. The student comprehension is hoped to increase with the use of practicum course.

Development of Android Based Powered Intelligent Wheelchair for Quadriplegic Persons

NASA Astrophysics Data System (ADS)

Gupta, Ashutosh; Ghosh, Tathagata; Kumar, Pradeep; Bhawna, Shruthi. S.

2017-08-01

Several surveys give us the view that both children and adults benefit substantially from access towards independent mobility. With the inventions of technology, no individuals are satisfied with traditional manual operated machines. To accommodate population, researchers are using technology, originally developed for mobile robots to create ‘intelligent wheelchairs’. It’s a major challenge for quadriplegic persons as they really find it difficult to manipulate powered wheelchair during the activities of their daily living. As the Smartphone era has evolved with innovative android based applications, engineers are improving and trying to make such machines simple and cheap to the next level. In this paper, we present a development of android based powered intelligent wheelchair to assist the quadriplegic person by making them self sufficient in controlling the wheelchair. The wheels of the chair can be controlled by the voice or gesture movement or by touching the screen of the android app by the challenged persons. The system uses the Bluetooth communication to interface the microcontroller and the inbuilt sensors in the android Smartphone. According to the commands received from android phone, the kinematics of the wheels are controlled.

Commercial Smartphone-Based Devices and Smart Applications for Personalized Healthcare Monitoring and Management.

PubMed

Vashist, Sandeep Kumar; Schneider, E Marion; Luong, John H T

2014-08-18

Smartphone-based devices and applications (SBDAs) with cost effectiveness and remote sensing are the most promising and effective means of delivering mobile healthcare (mHealthcare). Several SBDAs have been commercialized for the personalized monitoring and/or management of basic physiological parameters, such as blood pressure, weight, body analysis, pulse rate, electrocardiograph, blood glucose, blood glucose saturation, sleeping and physical activity. With advances in Bluetooth technology, software, cloud computing and remote sensing, SBDAs provide real-time on-site analysis and telemedicine opportunities in remote areas. This scenario is of utmost importance for developing countries, where the number of smartphone users is about 70% of 6.8 billion cell phone subscribers worldwide with limited access to basic healthcare service. The technology platform facilitates patient-doctor communication and the patients to effectively manage and keep track of their medical conditions. Besides tremendous healthcare cost savings, SBDAs are very critical for the monitoring and effective management of emerging epidemics and food contamination outbreaks. The next decade will witness pioneering advances and increasing applications of SBDAs in this exponentially growing field of mHealthcare. This article provides a critical review of commercial SBDAs that are being widely used for personalized healthcare monitoring and management.

Didactic satellite based on Android platform for space operation demonstration and development

NASA Astrophysics Data System (ADS)

Ben Bahri, Omar; Besbes, Kamel

2018-03-01

Space technology plays a pivotal role in society development. It offers new methods for telemetry, monitoring and control. However, this sector requires training, research and skills development but the lack of instruments, materials and budgets affects the ambiguity to understand satellite technology. The objective of this paper is to describe a demonstration prototype of a smart phone device for space operations study. Therefore, the first task was carried out to give a demonstration for spatial imagery and attitude determination missions through a wireless communication. The smart phone's Bluetooth was used to achieve this goal inclusive of a new method to enable real time transmission. In addition, an algorithm around a quaternion based Kalman filter was included in order to detect the reliability of the prototype's orientation. The second task was carried out to provide a demonstration for the attitude control mission using the smart phone's orientation sensor, including a new method for an autonomous guided mode. As a result, the acquisition platform showed real time measurement with good accuracy for orientation detection and image transmission. In addition, the prototype kept the balance during the demonstration based on the attitude control method.

Portable electrocardiograph through android application.

PubMed

De Oliveira, Igor H; Cene, V H; Balbinot, A

2015-01-01

An electrocardiograph was designed and implemented, being capable of obtaining electrical signals from the heart, and sending this data via Bluetooth to a tablet, in which the signals are graphically shown. The user interface is developed as an Android application. Because of the technological progress and the increasing use of full portable systems, such as tablets and cell phones, it is important to understand the functioning and development of an application, which provides a basis for conducting studies using this technology as an interface. The project development includes concepts of electronics and its application to achieve a portable and functional final project, besides using a specific programmable integrated circuit for electrocardiogram, electroencephalogram and electromyogram, the ADS1294. Using a simulator of cardiac signals, 36 different waveforms were recorded, including normal sinus rhythm, arrhythmias and artifacts. Simulations include variations of heart rate from 30 to 190 beats per minute (BPM), with variations in peak amplitude of 1 mV to 2 mV. Tests were performed with a subject at rest and in motion, observing the signals obtained and the damage to their interpretation due to the introduction of muscle movement artifacts in motion situations.

Analysis of Sources of Large Positioning Errors in Deterministic Fingerprinting

PubMed Central

2017-01-01

Wi-Fi fingerprinting is widely used for indoor positioning and indoor navigation due to the ubiquity of wireless networks, high proliferation of Wi-Fi-enabled mobile devices, and its reasonable positioning accuracy. The assumption is that the position can be estimated based on the received signal strength intensity from multiple wireless access points at a given point. The positioning accuracy, within a few meters, enables the use of Wi-Fi fingerprinting in many different applications. However, it has been detected that the positioning error might be very large in a few cases, which might prevent its use in applications with high accuracy positioning requirements. Hybrid methods are the new trend in indoor positioning since they benefit from multiple diverse technologies (Wi-Fi, Bluetooth, and Inertial Sensors, among many others) and, therefore, they can provide a more robust positioning accuracy. In order to have an optimal combination of technologies, it is crucial to identify when large errors occur and prevent the use of extremely bad positioning estimations in hybrid algorithms. This paper investigates why large positioning errors occur in Wi-Fi fingerprinting and how to detect them by using the received signal strength intensities. PMID:29186921

Advanced Reactor Technologies - Regulatory Technology Development Plan (RTDP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moe, Wayne L.

This DOE-NE Advanced Small Modular Reactor (AdvSMR) regulatory technology development plan (RTDP) will link critical DOE nuclear reactor technology development programs to important regulatory and policy-related issues likely to impact a “critical path” for establishing a viable commercial AdvSMR presence in the domestic energy market. Accordingly, the regulatory considerations that are set forth in the AdvSMR RTDP will not be limited to any one particular type or subset of advanced reactor technology(s) but rather broadly consider potential regulatory approaches and the licensing implications that accompany all DOE-sponsored research and technology development activity that deal with commercial non-light water reactors. However,more » it is also important to remember that certain “minimum” levels of design and safety approach knowledge concerning these technology(s) must be defined and available to an extent that supports appropriate pre-licensing regulatory analysis within the RTDP. Final resolution to advanced reactor licensing issues is most often predicated on the detailed design information and specific safety approach as documented in a facility license application and submitted for licensing review. Because the AdvSMR RTDP is focused on identifying and assessing the potential regulatory implications of DOE-sponsored reactor technology research very early in the pre-license application development phase, the information necessary to support a comprehensive regulatory analysis of a new reactor technology, and the resolution of resulting issues, will generally not be available. As such, the regulatory considerations documented in the RTDP should be considered an initial “first step” in the licensing process which will continue until a license is issued to build and operate the said nuclear facility. Because a facility license application relies heavily on the data and information generated by technology development studies, the anticipated

Advanced Reactor Technology -- Regulatory Technology Development Plan (RTDP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moe, Wayne Leland

This DOE-NE Advanced Small Modular Reactor (AdvSMR) regulatory technology development plan (RTDP) will link critical DOE nuclear reactor technology development programs to important regulatory and policy-related issues likely to impact a “critical path” for establishing a viable commercial AdvSMR presence in the domestic energy market. Accordingly, the regulatory considerations that are set forth in the AdvSMR RTDP will not be limited to any one particular type or subset of advanced reactor technology(s) but rather broadly consider potential regulatory approaches and the licensing implications that accompany all DOE-sponsored research and technology development activity that deal with commercial non-light water reactors. However,more » it is also important to remember that certain “minimum” levels of design and safety approach knowledge concerning these technology(s) must be defined and available to an extent that supports appropriate pre-licensing regulatory analysis within the RTDP. Final resolution to advanced reactor licensing issues is most often predicated on the detailed design information and specific safety approach as documented in a facility license application and submitted for licensing review. Because the AdvSMR RTDP is focused on identifying and assessing the potential regulatory implications of DOE-sponsored reactor technology research very early in the pre-license application development phase, the information necessary to support a comprehensive regulatory analysis of a new reactor technology, and the resolution of resulting issues, will generally not be available. As such, the regulatory considerations documented in the RTDP should be considered an initial “first step” in the licensing process which will continue until a license is issued to build and operate the said nuclear facility. Because a facility license application relies heavily on the data and information generated by technology development studies, the anticipated

The Impact of In-Service Technology Training Programmes on Technology Teachers

ERIC Educational Resources Information Center

Gumbo, Mishack; Makgato, Moses; Muller, Helene

2012-01-01

The aim of this paper is to assess the impact the Advanced Certificate in Education (ACE) in-service technology training program has on technology teachers' knowledge and understanding of technology. The training of technology teachers is an initiative toward teachers' professional development within the mathematics, science, and technology sphere…

The Impact of Experience and Technology Change on Task-Technology Fit of a Collaborative Technology

ERIC Educational Resources Information Center

Iversen, Jakob H.; Eierman, Michael A.

2018-01-01

This study continues a long running effort to examine collaborative writing and editing tools and the factors that impact Task-Technology Fit and Technology Acceptance. Previous studies found that MS Word/email performed better than technologies such as Twiki, Google Docs, and Office Live. The current study seeks to examine specifically the impact…

Radiated EMC immunity investigation of common recognition identification platform for medical applications

NASA Astrophysics Data System (ADS)

Miranda, Jorge; Cabral, Jorge; Ravelo, Blaise; Wagner, Stefan; Pedersen, Christian F.; Memon, Mukhtiar; Mathiesen, Morten

2015-01-01

An innovative e-healthcare platform named common recognition and identification platform (CRIP) was developed and tested as part of the CareStore project. CareStore and CRIP aims at delivering accurate and safe disease management by minimising human operator errors in hospitals and care facilities. To support this, the CRIP platform features fingerprint biometrics and near field communication (NFC) for user identification; and Bluetooth communication support for a range of telemedicine medical devices adhering to the IEEE 11073 standard. The aim of this study was to evaluate the electromagnetic compatibility (EMC) immunity of the CRIP platform in order to validate it for medical application use. The first prototype of CRIP was demonstrated to operate as expected by showing the user identification function feasibility, both via NFC and biometric, and by detection of Bluetooth devices via radio frequency (RF) scanning. The NFC module works in the 13.56 MHz band and the Bluetooth module work in the 2.4 GHz band, according to the IEEE 802.15.1 standard. The standard test qualification of the CRIP was performed based on the radiated EMC immunity with respect to the EN 61000-4-3 standard. The immunity tests were conducted under industrial EMC compliance with electric field aggression, with levels up to 10 V/m in both horizontal and vertical polarisations when the test antenna and the CRIP were placed at a distance of 3 m. It was found that the CRIP device complies with the European electromagnetic (EM) radiation immunity requirements.

Technology and the boundaries of the hospital: three emerging technologies.

PubMed

Goldsmith, Jeff

2004-01-01

U.S. hospitals have proved remarkably adept at altering their service offerings to incorporate new technologies. New technologies threatened to undercut hospitals' central role in health care delivery in the 1980s. An array of new technologies promise yet again to alter the boundaries of hospitals' franchise. These technologies will not only continue the shift away from acute, inpatient care that we have seen for the past thirty years but will also challenge hospitals to collaborate more effectively with physicians and technology developers. How hospitals and policymakers respond to these emerging technologies will help determine whether hospitals remain at the center of the U.S. health system.

Emerging Propulsion Technologies

NASA Technical Reports Server (NTRS)

Keys, Andrew S.

2006-01-01

The Emerging Propulsion Technologies (EPT) investment area is the newest area within the In-Space Propulsion Technology (ISPT) Project and strives to bridge technologies in the lower Technology Readiness Level (TRL) range (2 to 3) to the mid TRL range (4 to 6). A prioritization process, the Integrated In-Space Transportation Planning (IISTP), was developed and applied in FY01 to establish initial program priorities. The EPT investment area emerged for technologies that scored well in the IISTP but had a low technical maturity level. One particular technology, the Momentum-eXchange Electrodynamic-Reboost (MXER) tether, scored extraordinarily high and had broad applicability in the IISTP. However, its technical maturity was too low for ranking alongside technologies like the ion engine or aerocapture. Thus MXER tethers assumed top priority at EPT startup in FY03 with an aggressive schedule and adequate budget. It was originally envisioned that future technologies would enter the ISP portfolio through EPT, and EPT developed an EPT/ISP Entrance Process for future candidate ISP technologies. EPT has funded the following secondary, candidate ISP technologies at a low level: ultra-lightweight solar sails, general space/near-earth tether development, electrodynamic tether development, advanced electric propulsion, and in-space mechanism development. However, the scope of the ISPT program has focused over time to more closely match SMD needs and technology advancement successes. As a result, the funding for MXER and other EPT technologies is not currently available. Consequently, the MXER tether tasks and other EPT tasks were expected to phased out by November 2006. Presentation slides are presented which provide activity overviews for the aerocapture technology and emerging propulsion technology projects.

Understanding Technology Literacy: A Framework for Evaluating Educational Technology Integration

ERIC Educational Resources Information Center

Davies, Randall S.

2011-01-01

Federal legislation in the United States currently mandates that technology be integrated into school curricula because of the popular belief that learning is enhanced through the use of technology. The challenge for educators is to understand how best to teach with technology while developing the technological expertise of their students. This…

OAST system technology planning

NASA Technical Reports Server (NTRS)

Sadin, S. R.

1978-01-01

The NASA Office of Aeronautics and Space Technology developed a planning model for space technology consisting of a space systems technology model, technology forecasts and technology surveys. The technology model describes candidate space missions through the year 2000 and identifies their technology requirements. The technology surveys and technology forecasts provide, respectively, data on the current status and estimates of the projected status of relevant technologies. These tools are used to further the understanding of the activities and resources required to ensure the timely development of technological capabilities. Technology forecasting in the areas of information systems, spacecraft systems, transportation systems, and power systems are discussed.

The Struggle for Technology: Towards a Realistic Political Theory of Technology.

PubMed

Verbeek, Peter-Paul

2017-01-01

Pieter Lemmens' neo-Marxist approach to technology urges us to rethink how to do political philosophy of technology. First, Lemmens' high level of abstraction raises the question of how empirically informed a political theory of technology needs to be. Second, his dialectical focus on a "struggle" between humans and technologies reveals the limits of neo-Marxism. Political philosophy of technology needs to return "to the things themselves". The political significance of technologies cannot be reduced to its origins in systems of production or social organization, but requires study at the micro-level, where technologies help to shape engagement, interaction, power, and social awareness.

Technological Innovation of Thin-Film Transistors: Technology Development, History, and Future

NASA Astrophysics Data System (ADS)

Yamamoto, Yoshitaka

2012-06-01

The scale of the liquid crystal display industry has expanded rapidly, driven by technological innovations for thin-film transistors (TFTs). The TFT technology, which started from amorphous silicon (a-Si), has produced large TVs, and low-temperature polycrystalline silicon (poly-Si) has become a core technology for small displays, such as mobile phones. Recently, various TFT technological seeds have been realized, indicating that new information appliances that match new lifestyles and information infrastructures will be available in the near future. In this article, I review the history of TFT technology and discuss the future of TFT technological development from the technological innovation viewpoint.

ENVIRONMENTAL TECHNOLOGY VERIFICATION (ETV) PROGRAM: STORMWATER TECHNOLOGIES

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) program evaluates the performance of innovative air, water, pollution prevention and monitoring technologies that have the potential to improve human health and the environment. This techn...

"Obligatory Technologies": Explaining Why People Feel Compelled to Use Certain Technologies

ERIC Educational Resources Information Center

Chandler, Jennifer A.

2012-01-01

The ideas of technological determinism and the autonomy of technology are long-standing and widespread. This article explores why the use of certain technologies is perceived to be obligatory, thus fueling the fatalism of technological determinism and undermining our sense of freedom vis-a-vis the use of technologies. Three main mechanisms that…

Assistive Technologies

ERIC Educational Resources Information Center

Auat Cheein, Fernando A., Ed.

2012-01-01

This book offers the reader new achievements within the Assistive Technology field made by worldwide experts, covering aspects such as assistive technology focused on teaching and education, mobility, communication and social interactivity, among others. Each chapter included in this book covers one particular aspect of Assistive Technology that…

Technological Diffusion within Educational Institutions: Applying the Technology Acceptance Model.

ERIC Educational Resources Information Center

Wolski, Stacy; Jackson, Sally

Expectancy models of behavior such as the Theory of Reasoned Action (TRA) and the Technology Acceptance Model (TAM) offer guidelines that aid efforts to facilitate use of new technology. These models remind us that both acceptance of and resistance to technology use are grounded in beliefs and norms regarding the technology. Although TAM is widely…

SafeSlinger: An Easy-to-use and Secure Approach for Human Trust Establishment

DTIC Science & Technology

2012-03-12

communication modalities (Bluetooth, WiFi , 4G), camera, and sensors. Unfortunately, smartphone platforms suffer from many risks. Vulnerabilities exist in...December 2010. [31] Dave Neal. Defcon hackers get hacked over 4G. http://www.theinquirer.net/inquirer/news/ 16 2100989/defcon-hackers- hacked -4g

Microwave Scanning System Correlations

DTIC Science & Technology

2010-08-11

The follow equipment is needed for each of the individual scanning systems: Handheld Scanner Equipment list 1. Dell Netbook (with the...proper software installed by Evisive) 2. Bluetooth USB port transmitter 3. Handheld Probe 4. USB to mini-USB Converter (links camera to netbook

Science, technology, and pedagogy: Exploring secondary science teachers' effective uses of technology

NASA Astrophysics Data System (ADS)

Guzey, Siddika Selcen

Technology has become a vital part of our professional and personal lives. Today we cannot imagine living without many technological tools such as computers. For the last two decades technology has become inseparable from several areas, such as science. However, it has not been fully integrated into the field of education. The integration of technology in teaching and learning is still challenging even though there has been a historical growth of Internet access and available technology tools in schools (U.S. Department of Education, National Center for Education Statistics, 2006). Most teachers have not incorporated technology into their teaching for various reasons such as lack of knowledge of educational technology tools and having unfavorable beliefs about the effectiveness of technology on student learning. In this study, three beginning science teachers who have achieved successful technology integration were followed to investigate how their beliefs, knowledge, and identity contribute to their uses of technology in their classroom instruction. Extensive classroom observations and interviews were conducted. The findings demonstrate that the participating teachers are all intrinsically motivated to use technology in their teaching and this motivation allows them to enjoy using technology in their instruction and keeps them engaged in technology use. These teachers use a variety of technology tools in their instruction while also allowing students to use them, and they posit a belief set in favor of technology. The major findings of the study are displayed in a model which indicates that teachers' use of technology in classroom instruction was constructed jointly by their technology, pedagogy, and content knowledge; identity; beliefs; and the resources that are available to them and that the internalization of the technology use comes from reflection. The study has implications for teachers, teacher educators, and school administrators for successful technology

Mini Technology Manual for Schools: An Introduction to Technology Integration

ERIC Educational Resources Information Center

Grismore, Brian A.

2012-01-01

The purpose of this manual is to assist school leaders in beginning or developing the use of educational technology within their school or district. The manual covers topics: 1) advantages of educational technology; 2) types of technology used for learning and teaching; 3) how to make good decisions about the use of technology in schools; 4) the…

Technology Acquisition Reform

DTIC Science & Technology

2004-03-01

technologies until they are ready to be handed over to an established program. This office would also provide a home for disruptive technologies emerging...the development and acquisition of disruptive technologies .3 Disruptive technologies threaten programs of record but are essential to future Naval...and rarely emerge in response to customer demand. Disruptive technologies have features that a few fringe (and generally new) customers value

Entrepreneurship. Technology Learning Activity. Teacher Edition. Technology Education Series.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This packet of technology learning activity (TLA) materials on entrepreneurship for students in grades 6-10 consists of a technology education overview, information on use, and instructor's and student's sections. The overview discusses the technology education program and materials. Components of the instructor's and student's sections are…

Technological Tyranny

NASA Astrophysics Data System (ADS)

Greenwood, Dick

1984-08-01

It is implicitly assumed by those who create, develop, control and deploy new technology, as well as by society at-large, that technological innovation always represents progress. Such an unchallenged assumption precludes an examination and evaluation of the interrelationships and impact the development and use of technology have on larger public policy matters, such as preservation of democratic values, national security and military policies, employment, income and tax policies, foreign policy and the accountability of private corporate entities to society. This brief challenges those assumptions and calls for social control of technology.

Technology transfer

NASA Technical Reports Server (NTRS)

Handley, Thomas

1992-01-01

The requirements for a successful technology transfer program and what such a program would look like are discussed. In particular, the issues associated with technology transfer in general, and within the Jet Propulsion Laboratory (JPL) environment specifically are addressed. The section on background sets the stage, identifies the barriers to successful technology transfer, and suggests actions to address the barriers either generally or specifically. The section on technology transfer presents a process with its supporting management plan that is required to ensure a smooth transfer process. Viewgraphs are also included.

Digital Actuator Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ken Thomas; Ted Quinn; Jerry Mauck

There are significant developments underway in new types of actuators for power plant active components. Many of these make use of digital technology to provide a wide array of benefits in performance of the actuators and in reduced burden to maintain them. These new product offerings have gained considerable acceptance in use in process plants. In addition, they have been used in conventional power generation very successfully. This technology has been proven to deliver the benefits promised and substantiate the claims of improved performance. The nuclear industry has been reluctant to incorporate digital actuator technology into nuclear plant designs duemore » to concerns due to a number of concerns. These could be summarized as cost, regulatory uncertainty, and a certain comfort factor with legacy analog technology. The replacement opportunity for these types of components represents a decision point for whether to invest in more modern technology that would provide superior operational and maintenance benefits. Yet, the application of digital technology has been problematic for the nuclear industry, due to qualification and regulatory issues. With some notable exceptions, the result has been a continuing reluctance to undertake the risks and uncertainties of implementing digital actuator technology when replacement opportunities present themselves. Rather, utilities would typically prefer to accept the performance limitations of the legacy analog actuator technologies to avoid impacts to project costs and schedules. The purpose of this report is to demonstrate that the benefits of digital actuator technology can be significant in terms of plant performance and that it is worthwhile to address the barriers currently holding back the widespread development and use of this technology. It addresses two important objectives in pursuit of the beneficial use of digital actuator technology for nuclear power plants: 1. To demonstrate the benefits of digital actuator

Technological Determinism in Educational Technology Research: Some Alternative Ways of Thinking about the Relationship between Learning and Technology

ERIC Educational Resources Information Center

Oliver, M.

2011-01-01

This paper argues that research on the educational uses of technology frequently overemphasizes the influence of technology. Research in the field is considered a form of critical perspective, and assumptions about technology are questioned. Technological determinism is introduced, and different positions on this concept are identified. These are…

JPRS Report, Science & Technology, USSR: Science & Technology Policy.

DTIC Science & Technology

1987-07-07

fully reflect the end results of scientific and technical progress. The formation of the unified fund for the development of science and technology ...209058 JPRS-UST-87-009 7 JULY 1987 /ffifr FOREIGN BROADCAST INFORMATION SERVICE JPRS Repor Science & Technology USSR: Science... Technology Policy 19980715 121 REPRODUCED BY U.S. DEPARTMENTOF COMMERCE NATIONAL TECHNICAL •^ INFORMATIONSERVICE A rf *r*lQ ürjA T Tw» SPRINGFIELD, VA

EPA'S ENVIRONMENTAL TECHNOLOGIES

EPA Science Inventory

The use of innovative technology is impeded by the lack of independent, credible information as to how the technology performs. Such data is needed by technology buyers and regulatory decision makers to make informed decisions on technologies that represent good financial invest...

SITE TECHNOLOGY CAPSULE: BIOGENESIS SOIL WASHING TECHNOLOGY

EPA Science Inventory

Soil washing technologies are designed to transfer contaminants from soil to a liquid phase. The BloGenesis™ soil washing technology uses a proprietary surfactant solution to transfer organic contaminants from soil to wastewater. The surfactant used in the soil washing process wa...

Payload software technology: Software technology development plan

NASA Technical Reports Server (NTRS)

1977-01-01

Programmatic requirements for the advancement of software technology are identified for meeting the space flight requirements in the 1980 to 1990 time period. The development items are described, and software technology item derivation worksheets are presented along with the cost/time/priority assessments.

Positive technology: using interactive technologies to promote positive functioning.

PubMed

Riva, Giuseppe; Baños, Rosa M; Botella, Cristina; Wiederhold, Brenda K; Gaggioli, Andrea

2012-02-01

It is generally assumed that technology assists individuals in improving the quality of their lives. However, the impact of new technologies and media on well-being and positive functioning is still somewhat controversial. In this paper, we contend that the quality of experience should become the guiding principle in the design and development of new technologies, as well as a primary metric for the evaluation of their applications. The emerging discipline of Positive Psychology provides a useful framework to address this challenge. Positive Psychology is the scientific study of optimal human functioning and flourishing. Instead of drawing on a "disease model" of human behavior, it focuses on factors that enable individuals and communities to thrive and build the best in life. In this paper, we propose the "Positive Technology" approach--the scientific and applied approach to the use of technology for improving the quality of our personal experience through its structuring, augmentation, and/or replacement--as a way of framing a suitable object of study in the field of cyberpsychology and human-computer interaction. Specifically, we suggest that it is possible to use technology to influence three specific features of our experience--affective quality, engagement/actualization, and connectedness--that serve to promote adaptive behaviors and positive functioning. In this framework, positive technologies are classified according to their effects on a specific feature of personal experience. Moreover, for each level, we have identified critical variables that can be manipulated to guide the design and development of positive technologies.

An Educational Technology Curriculum for Converging Technologies.

ERIC Educational Resources Information Center

Allen, Brockenbrough S.; And Others

1989-01-01

Outlines curriculum reforms being made in the master's level educational technology program at San Diego State University. Topics discussed include technological changes and the roles of educational product designers; human information processing; knowledge base design; student design of educational adventure games; interactive video design; and…

Identifying Students with Gifts and Talents in Technology. Technology

ERIC Educational Resources Information Center

Siegle, Del

2004-01-01

Technology expertise often occurs in two types of technology activities. One area of expertise is computer programming and another is expertise as a technology consumer using hardware and software. In addition to demonstrating prowess, some students tend to exhibit passion toward one or both of these activities. Students who excel in either could…

Control Robotics Programming Technology. Technology Learning Activity. Teacher Edition.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This Technology Learning Activity (TLA) for control robotics programming technology in grades 6-10 is designed to teach students to construct and program computer-controlled devices using a LEGO DACTA set and computer interface and to help them understand how control technology and robotics affect them and their lifestyle. The suggested time for…

Mars Technology Program: Planetary Protection Technology Development

NASA Technical Reports Server (NTRS)

Lin, Ying

2006-01-01

This slide presentation reviews the development of Planetary Protection Technology in the Mars Technology Program. The goal of the program is to develop technologies that will enable NASA to build, launch, and operate a mission that has subsystems with different Planetary Protection (PP) classifications, specifically for operating a Category IVb-equivalent subsystem from a Category IVa platform. The IVa category of planetary protection requires bioburden reduction (i.e., no sterilization is required) The IVb category in addition to IVa requirements: (i.e., terminal sterilization of spacecraft is required). The differences between the categories are further reviewed.

Technology in TESOL.

ERIC Educational Resources Information Center

TESOL Journal, 1993

1993-01-01

This special issue is devoted to the theme of advancing technology in the teaching of English to speakers of other languages (TESOL). Articles include: "Technology in TESOL" (Richard Orem, Cynthia Holliday); TESOL Technology: Imposition or Opportunity?" (Simon Murison-Bowie); "A Review of Advanced Technologies for L2…

The Technological Personality

ERIC Educational Resources Information Center

Stivers, Richard

2004-01-01

If technology is the single most important factor in explaining the organization of modern societies, it is likewise the key to understanding the modern personality. The technological personality is the psychological counterpart to the technological society.Technology indirectly destroys the basis of a common morality and so leaves human…

Hackers against technology: Critique and recuperation in technological cycles.

PubMed

Maxigas

2017-12-01

I offer an interpretation of hackers' technological choices through a theoretical framework of critique and recuperation in technological cycles, building on prior research that brings the pragmatic sociology of Boltanski and Chiapello to bear on matters in Science and Technology Studies. I argue that contextualizing technology choices in the development of capitalism through innovation illuminates their political significance. I start with the counterintuitive observation that some browser extensions popular with hackers, like RequestPolicy, make it considerably harder for them to look at websites. This observation showcases the Luddite aspects of hackerdom, in that they are willing to 'break' popular websites that would otherwise cheat on the user. In line with an undercurrent of hacker studies, in this case study I find hackers fighting technological progress they see as social decline.

A model for technology assessment and commercialization for innovative disruptive technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

KASSICIEH, SULEIMAN K.; WALSH, STEVE; MCWHORTER,PAUL J.

2000-05-17

Disruptive technologies are scientific discoveries that break through the usual product technology capabilities and provide a basis for a new competitive paradigm as described by Anderson and Tushman [1990], Tushman and Rosenkopf [1992], and Bower and Christensen [1995]. Discontinuous innovations are products/processes/services that provide exponential improvements in the value received by the customer much in the same vein as Walsh [1996], Lynn, Morone and Paulson [1996], and Veryzer [1998]. For more on definitions of disruptive technologies and discontinuous innovations, see Walsh and Linton [1999] who provide a number of definitions for disruptive technologies and discontinuous innovations. Disruptive technologies and discontinuousmore » innovations present a unique challenge and opportunity for R and D organizations seeking to build their commercialization efforts and to reinvent the corporation. These technologies do not have a proven path from scientific discovery to mass production and therefore require novel approaches. These critically important technologies are the wellspring of wealth creation and new competency generation but are not readily accepted by the corporate community. They are alternatively embraced and eschewed by the commercial community. They are finally accepted when the technology has already affected the industry or when the technological horse has already flown out of the hanger. Many firms, especially larger firms, seem reluctant to familiarize themselves with these technologies quickly. The trend seems to be that these firms prefer to react to a proven disruptive technology that has changed the product market paradigm. If true, then there is cause for concern. This paper will review the literature on disruptive technologies presenting a model of the progression from scientific idea to mass production for disruptive technologies contrasted to the more copious incremental technologies. The paper will then describe Sandia National

ENVIRONMENTAL TECHNOLOGY VERIFICATION FOR AIR POLLUTION CONTROL TECHNOLOGIES: FINAL REPORT

EPA Science Inventory

The technical objective of the Environmental Technology Verification (ETV) Program's Air Pollution Control Technology (APCT) Center is to verify environmental technology performance by obtaining objective quality-assured data, thus providing potential purchasers and permitters wi...

Search Technologies | NCI Technology Transfer Center | TTC

Cancer.gov

Our team of technology transfer specialists has specialized training in invention reporting, patenting, patent strategy, executing technology transfer agreements and marketing. TTC is comprised of professionals with diverse legal, scientific, and business/marketing expertise. Most of our staff hold doctorate-level technical and/or legal training.

Available Technologies | NCI Technology Transfer Center | TTC

Cancer.gov

Our team of technology transfer specialists has specialized training in invention reporting, patenting, patent strategy, executing technology transfer agreements and marketing. TTC is comprised of professionals with diverse legal, scientific, and business/marketing expertise. Most of our staff hold doctorate-level technical and/or legal training.

Different Perspectives on Technology Acceptance: The Role of Technology Type and Age

NASA Astrophysics Data System (ADS)

Arning, Katrin; Ziefle, Martina

Although eHealth technologies offer an enormous potential to improve healthcare, the knowledge about key determinants of acceptance for eHealth technology is restricted. While the underlying technology of eHealth technologies and Information and Communication technology (ICT) is quite similar, utilization contexts and using motives are quite different. In order to explore the role of technology type on acceptance, we contrasted central application characteristics of both technology types using the scenario technique. A questionnaire was administered (n = 104) measuring individual variables (age, gender) and attitudes regarding an eHealth application (blood sugar meter) in contrast to an ICT device (Personal Digital Assistant, PDA). Older users basically approved the utilization of health-related technologies and perceived lower usability barriers. In addition, we identified main utilization motives of eHealth technology and technology-specific acceptance patterns, especially regarding issues of data safety in the eHealth context. Effects of age and gender in acceptance ratings suggest a differential perspective on eHealth acceptance. Finally, practical interventions were derived in order to support eHealth device design and to promote acceptance of eHealth technology.

Tomographic Imaging on Distributed Unattended Ground Sensor Arrays

DTIC Science & Technology

2002-05-14

communication, the recently released Bluetooth standard warrants investigation into its usefulness on ground sensors. Although not as powerful or as fast...NTSC,” June 2001, http://archive.ncsa.uiuc.edu/ SCMS /training/general/details/ntsc.html [14] Techfest, “PCI local bus technical summary,” 1999, http

Technology in the Montessori Classroom: Teachers' Beliefs and Technology Use

ERIC Educational Resources Information Center

Jones, Sara J.

2017-01-01

As technology becomes ubiquitous in society, there is increasing momentum to incorporate it into education. Montessori education is not immune to this push for technology integration. This qualitative study investigates four Upper Elementary Montessori teachers' attitudes toward technology and technology integration in a public school setting.…

2017 Technology Showcase | NCI Technology Transfer Center | TTC

Cancer.gov

The 2017 Technology Showcase is an inaugural, half-day event showcased technologies developed by the National Cancer Institute's Center for Cancer Research (CCR) and the Frederick National Laboratory for Cancer Research (FNLCR).

Fabrication Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blaedel, K.L.

1993-03-01

The mission of the Fabrication Technology thrust area is to have an adequate base of manufacturing technology, not necessarily resident at Lawrence Livermore National Laboratory (LLNL), to conduct the future business of LLNL. The specific goals continue to be to (1) develop an understanding of fundamental fabrication processes; (2) construct general purpose process models that will have wide applicability; (3) document findings and models in journals; (4) transfer technology to LLNL programs, industry, and colleagues; and (5) develop continuing relationships with the industrial and academic communities to advance the collective understanding of fabrication processes. The strategy to ensure success ismore » changing. For technologies in which they are expert and which will continue to be of future importance to LLNL, they can often attract outside resources both to maintain their expertise by applying it to a specific problem and to help fund further development. A popular vehicle to fund such work is the Cooperative Research and Development Agreement with industry. For technologies needing development because of their future critical importance and in which they are not expert, they use internal funding sources. These latter are the topics of the thrust area. Three FY-92 funded projects are discussed in this section. Each project clearly moves the Fabrication Technology thrust area towards the goals outlined above. They have also continued their membership in the North Carolina State University Precision Engineering Center, a multidisciplinary research and graduate program established to provide the new technologies needed by high-technology institutions in the US. As members, they have access to and use of the results of their research projects, many of which parallel the precision engineering efforts at LLNL.« less

Fabrication technology

NASA Astrophysics Data System (ADS)

Blaedel, K. L.

1993-03-01

The mission of the Fabrication Technology thrust area is to have an adequate base of manufacturing technology, not necessarily resident at Lawrence Livermore National Laboratory (LLNL), to conduct the future business of LLNL. The specific goals continue to be to do the following: (1) develop an understanding of fundamental fabrication processes; (2) construct general purpose process models that will have wide applicability; (3) document findings and models in journals; (4) transfer technology to LLNL programs, industry, and colleagues; and (5) develop continuing relationships with the industrial and academic communities to advance the collective understanding of fabrication processes. The strategy to ensure success is changing. For technologies in which they are expert and which will continue to be of future importance to LLNL, they can often attract outside resources both to maintain their expertise by applying it to a specific problem and to help fund further development. A popular vehicle to fund such work is the Cooperative Research and Development Agreement with industry. For technologies needing development because of their future critical importance and in which they are not expert, they use internal funding sources. These latter are the topics of the thrust area. Three FY-92 funded projects are discussed in this section. Each project clearly moves the Fabrication Technology thrust area towards the goals outlined above. They have also continued their membership in the North Carolina State University Precision Engineering Center, a multidisciplinary research and graduate program established to provide the new technologies needed by high-technology institutions in the U.S. As members, they have access to and use of the results of their research projects, many of which parallel the precision engineering efforts at LLNL.

GENERAL ENVIRONMENTAL CORPORATION; CURE ELECTROCOAGULATION TECHNOLOGY: INNOVATIVE TECHNOLOGY EVALUATION REPORT

EPA Science Inventory

The CURE electrocoagulation technology was demonstrated under the Superfund Innovative Technology Evaluation (SITE) program at the U.S. Department of Energy (DOE) Rocky Flats Environmental Technology Site (RFETS), where water from the solar evaporation ponds (SEPs) was contaminat...

Development of intelligent monitoring purifier for indoor PM 2.5

NASA Astrophysics Data System (ADS)

Lou, Guanting; Zhu, Rong; Guo, Jiangwei; Wei, Yongqing

2018-03-01

The particulate matter 2.5 (PM2.5) refers to tiny particles or droplets in the air that are two and one half microns or less in width. PM2.5 is an air pollutant that is a concern for people’s health when levels in air are high. The intelligent monitoring purifier was developed to detect indoor PM2.5 concentration before and after purification and the monitoring data could be displayed on the LCD screen, displaying different color patterns according to the concentrations. Through the Bluetooth transport module, real-time values could also display on the mobile phone and voice broadcast PM2.5 concentration level in the air. When PM2.5 concentration is higher than the setting threshold, the convection fan rotation and the speed can be remote controlled with mobile phone through the Bluetooth transport. Therefore, the efficiency and scope of the purification could be enhanced and further better air quality could be achieved.

Mobile messaging services-based personal electrocardiogram monitoring system.

PubMed

Tahat, Ashraf A

2009-01-01

A mobile monitoring system utilizing Bluetooth and mobile messaging services (MMS/SMSs) with low-cost hardware equipment is proposed. A proof of concept prototype has been developed and implemented to enable transmission of an Electrocardiogram (ECG) signal and body temperature of a patient, which can be expanded to include other vital signs. Communication between a mobile smart-phone and the ECG and temperature acquisition apparatus is implemented using the popular personal area network standard specification Bluetooth. When utilizing MMS for transmission, the mobile phone plots the received ECG signal and displays the temperature using special application software running on the client mobile phone itself, where the plot can be captured and saved as an image before transmission. Alternatively, SMS can be selected as a transmission means, where in this scenario, dedicated application software is required at the receiving device. The experimental setup can be operated for monitoring from anywhere in the globe covered by a cellular network that offers data services.

Mobile Messaging Services-Based Personal Electrocardiogram Monitoring System

PubMed Central

Tahat, Ashraf A.

2009-01-01

A mobile monitoring system utilizing Bluetooth and mobile messaging services (MMS/SMSs) with low-cost hardware equipment is proposed. A proof of concept prototype has been developed and implemented to enable transmission of an Electrocardiogram (ECG) signal and body temperature of a patient, which can be expanded to include other vital signs. Communication between a mobile smart-phone and the ECG and temperature acquisition apparatus is implemented using the popular personal area network standard specification Bluetooth. When utilizing MMS for transmission, the mobile phone plots the received ECG signal and displays the temperature using special application software running on the client mobile phone itself, where the plot can be captured and saved as an image before transmission. Alternatively, SMS can be selected as a transmission means, where in this scenario, dedicated application software is required at the receiving device. The experimental setup can be operated for monitoring from anywhere in the globe covered by a cellular network that offers data services. PMID:19707531

A wireless breathing-training support system for kinesitherapy.

PubMed

Tawa, Hiroki; Yonezawa, Yoshiharu; Maki, Hiromichi; Ogawa, Hidekuni; Ninomiya, Ishio; Sada, Kouji; Hamada, Shingo; Caldwell, W Morton

2009-01-01

We have developed a new wireless breathing-training support system for kinesitherapy. The system consists of an optical sensor, an accelerometer, a microcontroller, a Bluetooth module and a laptop computer. The optical sensor, which is attached to the patient's chest, measures chest circumference. The low frequency components of circumference are mainly generated by breathing. The optical sensor outputs the circumference as serial digital data. The accelerometer measures the dynamic acceleration force produced by exercise, such as walking. The microcontroller sequentially samples this force. The acceleration force and chest circumference are sent sequentially via Bluetooth to a physical therapist's laptop computer, which receives and stores the data. The computer simultaneously displays these data so that the physical therapist can monitor the patient's breathing and acceleration waveforms and give instructions to the patient in real time during exercise. Moreover, the system enables a quantitative training evaluation and calculation the volume of air inspired and expired by the lungs.

Remote Arrhythmia Monitoring System Developed

NASA Technical Reports Server (NTRS)

York, David W.; Mackin, Michael A.; Liszka, Kathy J.; Lichter, Michael J.

2004-01-01

Telemedicine is taking a step forward with the efforts of team members from the NASA Glenn Research Center, the MetroHealth campus of Case Western University, and the University of Akron. The Arrhythmia Monitoring System is a completed, working test bed developed at Glenn that collects real-time electrocardiogram (ECG) signals from a mobile or homebound patient, combines these signals with global positioning system (GPS) location data, and transmits them to a remote station for display and monitoring. Approximately 300,000 Americans die every year from sudden heart attacks, which are arrhythmia cases. However, not all patients identified at risk for arrhythmias can be monitored continuously because of technological and economical limitations. Such patients, who are at moderate risk of arrhythmias, would benefit from technology that would permit long-term continuous monitoring of electrical cardiac rhythms outside the hospital environment. Embedded Web Technology developed at Glenn to remotely command and collect data from embedded systems using Web technology is the catalyst for this new telemetry system (ref. 1). In the end-to-end system architecture, ECG signals are collected from a patient using an event recorder and are transmitted to a handheld personal digital assistant (PDA) using Bluetooth, a short-range wireless technology. The PDA concurrently tracks the patient's location via a connection to a GPS receiver. A long distance link is established via a standard Internet connection over a 2.5-generation Global System for Mobile Communications/General Packet Radio Service (GSM/GPRS)1 cellular, wireless infrastructure. Then, the digital signal is transmitted to a call center for monitoring by medical professionals.

Technology 2000, volume 2

NASA Technical Reports Server (NTRS)

1991-01-01

Technology 2000 was the first major industrial conference and exposition spotlighting NASA technology and technology transfer. It's purpose was, and continues to be, to increase awareness of existing NASA-developed technologies that are available for immediate use in the development of new products and processes, and to lay the groundwork for the effective utilization of emerging technologies. Included are sessions on: computer technology and software engineering; human factors engineering and life sciences; materials science; sensors and measurement technology; artificial intelligence; environmental technology; optics and communications; and superconductivity.

SUPERFUND INNOVATIVE TECHNOLOGY EVALUATION PROGRAM - TECHNOLOGY PROFILES 4th Edition

EPA Science Inventory

The Superfund Innovative Technology Evaluation (SITE) Program evaluates new and promising treatment technologies for cleanup of hazardous waste sites. The program was created to encourage the development and routine use of innovative treatment technologies. As a result, the SI...

When technology, science and culture meet: insights from ancient Chinese technology

NASA Astrophysics Data System (ADS)

Lee, Yeung Chung

2017-10-01

This paper draws together two important agendas in science education. The first is making science education more inclusive such that students from non-Western or indigenous cultures can benefit from culturally relevant curricula. The second is integrating technology into the curriculum under the umbrella of Science-Technology-Society (STS) education to embrace the social aspects of science, with technology serving as a bridge. The advancement of the first agenda is hindered by the pursuance by both Western and non-Western societies of narrow cultural and practical goals without considering the development of science and technology from a cross-cultural perspective. The second agenda is limited by the misconception that technology is applied science, leading to the exclusion from STS discussions of pre-science or indigenous technologies developed by non-Western cultures. Through selected case studies of the evolution of Chinese traditional technologies and their interaction with science, this paper offers a perspective from the Far East, and argues for situating culturally responsive science education in broader historical and cross-cultural contexts to acknowledge the multi-cultural contributions to science and technology. A form of cross-cultural STS education is advanced, encompassing the cultural basis of technological developments, technology diffusion, interactions of traditional technology with science, and the potential development of traditional or indigenous technologies. This approach provides a bridge between the existing universal science education paradigm promoted in the West and the different forms of multi-cultural education advocated by indigenous science educators. To translate theory into practice, a conceptual framework is proposed in which the essential transdisciplinary knowledge base, curricular goals, and pedagogical approaches are embedded.

The Technology Boom

PubMed Central

Gilmore, L. Anne; Duhé, Abby F.; Frost, Elizabeth A.

2014-01-01

As technology continues to develop rapidly, the incidence of obesity also continues to climb at an alarming rate. The increase in available technology is thought to be a contributor in the obesogenic environment, yet at the same time technology can also be used to intervene and improve health and health behaviors. This article reviews the components of effective weight management programs and the novel role that technology, such as SMS, websites, and smartphone apps, is playing to improve the success of such programs. Use of these modern technologies can now allow for individualized treatment recommendations to be delivered to individuals remotely, increased self-monitoring/tracking of health-related data, broader and more rapid dissemination of health information/recommendations, and increased patient–dietician/physician contact. The use of technology in weight management programs results in improved long-term weight management, and in most cases improved cost-effectiveness. Rather than blaming increased food intake and sedentary lifestyle on technology, rapidly developing and innovative technologies should be used to our advantage and deployed to combat the obesity epidemic. PMID:24876625

Aerospace Structures Technology Damping Design Guide. Volume 1. Technology Review

DTIC Science & Technology

1985-12-01

AFWAL-TR-84-3089 Volume I AEROSPACE STRUCTURES TECHNOLOGY I DAMPING DESIGN GUIDE VOLUME I - TECHNOLOGY REVIEW J. SOOVERE LOCKHEED CALIFORNIA COMPANY...3089 Volume I AEROSPACE STRUCTURES TECHNOLOGY DAMPING DESIGN GUIDE VOLUME I - TECHNOLOGY REVIEW J. SOOVERE LOCKMD CALIFORNIA COMPANY P.O. BOX 551 BURBANK...PATTERSON AIR FORCE BASE, OHIO 454t33I I ft NOTICE When Government drawings, specifications, or other data are used for any purpose other than in

Hot Technologies for K-12 Schools: The 2005 Guide for Technology Decision Makers. COSN's Emerging Technologies Series

ERIC Educational Resources Information Center

Vockley, Martha, Ed.

2004-01-01

As technology companies introduce innovative products and services for the education market, school districts have the opportunity to invest in technologies designed to improve instruction and operations--from teaching, learning and assessments to organizational efficiency. Perhaps the greatest promise of anticipated technologies is their…

Analysis of Impact of 3D Printing Technology on Traditional Manufacturing Technology

NASA Astrophysics Data System (ADS)

Wu, Niyan; Chen, Qi; Liao, Linzhi; Wang, Xin

With quiet rise of 3D printing technology in automobile, aerospace, industry, medical treatment and other fields, many insiders hold different opinions on its development. This paper objectively analyzes impact of 3D printing technology on mold making technology and puts forward the idea of fusion and complementation of 3D printing technology and mold making technology through comparing advantages and disadvantages of 3D printing mold and traditional mold making technology.

Design and Development of Multi-Transceiver Lorafi Board consisting LoRa and ESP8266-Wifi Communication Module

NASA Astrophysics Data System (ADS)

Azmi, Noraini; Sudin, Sukhairi; Munirah Kamarudin, Latifah; Zakaria, Ammar; Visvanathan, Retnam; Chew Cheik, Goh; Mamduh Syed Zakaria, Syed Muhammad; Abdullah Alfarhan, Khudhur; Badlishah Ahmad, R.

2018-03-01

The advancement of Micro-Electro-Mechanical-Systems (MEMS), microcontroller technologies and the idea of Internet of Things (IoT) motivates the development of wireless modules (e.g. WiFi, Bluetooth, Zigbee, and LoRa) that are small and affordable. This paper aims to provide detailed information on the development of the LoRaFi board. The LoRaFi 1.0 is a multi-protocol communication board developed by Centre of Excellence for Advanced Sensor Technology (CEASTech). The board was developed for but not limited to monitor the indoor air quality. The board comprises two different wireless communication modules namely, Long-range technology (LoRa) and WiFi (using ESP8266). The board can be configured to communicate either using LoRa or WiFi or both. The board has been tested and the wireless communication operates successfully. Apart from LoRa, WiFi enables data to be forwarded to the cloud/server where the data can be stored for further data analysis. This helps provide users with real-time information on their smartphones or other applications. In the future, researchers will conduct tests to investigate the communication link quality. Newer version with reduced board size and additional wireless communication module will be developed in the future as to increase board flexibility and widen the range of applications that can use the board.

Extend Course for Product Designer in Digital Mobile Era

NASA Astrophysics Data System (ADS)

CHAO, Fang-Lin; LIU, Tzu-Heng; HUANG, Xian-Chun

2017-12-01

Product design refers to a system of processes from confirming a product’s specifications to product’s structure. Form, technology, and needs must be considered simultaneously to ensure qualities. In recent years, with the advancement of smartphone technology, many products are connected with apps. Designers cannot exclude themselves from this new wave of the trend. In this article, household hydroponic products design is used as an example, to show the close relationship between digital mobile technology and product design in the contemporary world. Regularly measure the amount of liquid to be added is difficult for a consumer who has no professional experience. To facilitate the introduction of small-scale aquaculture systems into the home, we proposed sensor hardware combined with App software, measured EC and pH value and transmitted to the phone. The app can calculate and display the amount of added and control the amount of inserted through a Bluetooth connection. The physical design needs to take into account the connection between the electronic parts and the circuit board, and interface operation. Thus, not only the model of the product but also the user interface has to be integrated to show the product's quality completely. Besides, authors made reflection upon the necessity for adjustments for interdisciplinary courses under the changing digital mobile era. Also, under the current curriculum structure, possible teaching approach is expressed for extending student’s feasibility.

The ultimate technology: the end of technology and the task of nature.

PubMed

Riis, Søren

2013-01-01

One of the most influential philosophers of the 20th century, Martin Heidegger (1889-1976), died prior to the remarkable cloning of the sheep Dolly and before Dr. Venter started his experiments on creating synthetic life, and he never explicitly discussed living technologies. However, by reinterpreting his notion of "modern technology," this article shows how it is possible to philosophically assess living technologies and to recognize ways in which Heidegger anticipated this phenomenon with his notion of cybernetics. The interpretation elucidates the fundamental process of technology becoming living and simultaneously presents living technology as the ultimate technology. The thesis of this article is that living technology is not just one more technology; rather, it is the perfection of technology as understood by Aristotle. Aristotle's thinking is in this way a key example of a profound reassessment of nature and technology. Aristotle clearly separates these two domains of being in his definition, but in doing so, he also connects them to one another in a highly influential way. Following this line of thought, the article finally offers an original perspective involving renewed respect for the perpetual self-unfolding nature of living technology.