A Low-cost 4 Bit, 10 Giga-samples-per-second Analog-to-digital Converter Printed Circuit Board Assembly for FPGA-based Backends

NASA Astrophysics Data System (ADS)

Jiang, Homin; Yu, Chen-Yu; Kubo, Derek; Chen, Ming-Tang; Guzzino, Kim

2016-11-01

In this study, a 4 bit, 10 giga-samples-per-second analog-to-digital converter (ADC) printed circuit board assembly (PCBA) was designed, manufactured, and characterized for digitizing radio telescopes. For this purpose, an Adsantec ANST7120A-KMA flash ADC chip was used. Together with the field-programmable gate array platform, developed by the Collaboration for Astronomy Signal Processing and Electronics Research community, the PCBA enables data acquisition with a wide bandwidth and simplifies the intermediate frequency section. In the current version, the PCBA and the chip exhibit an analog bandwidth of 10 GHz (3 dB loss) and 20 GHz, respectively, which facilitates second, third, and even fourth Nyquist sampling. The following average performance parameters were obtained from the first and second Nyquist zones of the three boards: a spurious-free dynamic range of 31.35/30.45 dB, a signal-to-noise and distortion ratio of 22.95/21.83 dB, and an effective number of bits of 3.65/3.43, respectively.

High-Speed Isolation Board for Flight Hardware Testing

NASA Technical Reports Server (NTRS)

Yamamoto, Clifford K.; Goodpasture, Richard L.

2011-01-01

There is a need to provide a portable and cost-effective galvanic isolation between ground support equipment and flight hardware such that any unforeseen voltage differential between ground and power supplies is eliminated. An interface board was designed for use between the ground support equipment and the flight hardware that electrically isolates all input and output signals and faithfully reproduces them on each side of the interface. It utilizes highly integrated multi-channel isolating devices to minimize size and reduce assembly time. This single-board solution provides appropriate connector hardware and breakout of required flight signals to individual connectors as needed for various ground support equipment. The board utilizes multi-channel integrated circuits that contain transformer coupling, thereby allowing input and output signals to be isolated from one another while still providing high-fidelity reproduction of the signal up to 90 MHz. The board also takes in a single-voltage power supply input from the ground support equipment and in turn provides a transformer-derived isolated voltage supply to power the portion of the circuitry that is electrically connected to the flight hardware. Prior designs used expensive opto-isolated couplers that were required for each signal to isolate and were time-consuming to assemble. In addition, these earlier designs were bulky and required a 2U rack-mount enclosure. The new design is smaller than a piece of 8.5 11-in. (.22 28-mm) paper and can be easily hand-carried where needed. The flight hardware in question is based on a lineage of existing software-defined radios (SDRs) that utilize a common interface connector with many similar input-output signals present. There are currently four to five variations of this SDR, and more upcoming versions are planned based on the more recent design.

Column Grid Array Rework for High Reliability

NASA Technical Reports Server (NTRS)

Mehta, Atul C.; Bodie, Charles C.

2008-01-01

Due to requirements for reduced size and weight, use of grid array packages in space applications has become common place. To meet the requirement of high reliability and high number of I/Os, ceramic column grid array packages (CCGA) were selected for major electronic components used in next MARS Rover mission (specifically high density Field Programmable Gate Arrays). ABSTRACT The probability of removal and replacement of these devices on the actual flight printed wiring board assemblies is deemed to be very high because of last minute discoveries in final test which will dictate changes in the firmware. The questions and challenges presented to the manufacturing organizations engaged in the production of high reliability electronic assemblies are, Is the reliability of the PWBA adversely affected by rework (removal and replacement) of the CGA package? and How many times can we rework the same board without destroying a pad or degrading the lifetime of the assembly? To answer these questions, the most complex printed wiring board assembly used by the project was chosen to be used as the test vehicle, the PWB was modified to provide a daisy chain pattern, and a number of bare PWB s were acquired to this modified design. Non-functional 624 pin CGA packages with internal daisy chained matching the pattern on the PWB were procured. The combination of the modified PWB and the daisy chained packages enables continuity measurements of every soldered contact during subsequent testing and thermal cycling. Several test vehicles boards were assembled, reworked and then thermal cycled to assess the reliability of the solder joints and board material including pads and traces near the CGA. The details of rework process and results of thermal cycling are presented in this paper.

49 CFR 177.835 - Class 1 materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... wheel base of less than 184 inches; (3) Any vehicle in the combination is a cargo tank which is required... Army, Navy or Air Force of the United States Government provided the Class 1 (explosive) materials are... boards, or any similar projections. (g) No detonator assembly or booster with detonator may be...

49 CFR 177.835 - Class 1 materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... wheel base of less than 184 inches; (3) Any vehicle in the combination is a cargo tank which is required... Army, Navy or Air Force of the United States Government provided the Class 1 (explosive) materials are... boards, or any similar projections. (g) No detonator assembly or booster with detonator may be...

49 CFR 177.835 - Class 1 materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... wheel base of less than 184 inches; (3) Any vehicle in the combination is a cargo tank which is required... Army, Navy or Air Force of the United States Government provided the Class 1 (explosive) materials are... boards, or any similar projections. (g) No detonator assembly or booster with detonator may be...

49 CFR 177.835 - Class 1 materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... wheel base of less than 184 inches; (3) Any vehicle in the combination is a cargo tank which is required... Army, Navy or Air Force of the United States Government provided the Class 1 (explosive) materials are... boards, or any similar projections. (g) No detonator assembly or booster with detonator may be...

49 CFR 177.835 - Class 1 materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... wheel base of less than 184 inches; (3) Any vehicle in the combination is a cargo tank which is required... Army, Navy or Air Force of the United States Government provided the Class 1 (explosive) materials are... boards, or any similar projections. (g) No detonator assembly or booster with detonator may be...

Process Development for Automated Solar Cell and Module Production. Task 4: Automated Array Assembly

NASA Technical Reports Server (NTRS)

Hagerty, J. J.

1981-01-01

The Automated Lamination Station is mechanically complete and is currently undergoing final wiring. The high current driver and isolator boards have been completed and installed, and the main interface board is under construction. The automated vacuum chamber has had a minor redesign to increase stiffness and improve the cover open/close mechanism. Design of the Final Assembly Station has been completed and construction is underway.

Rework of multilayer printed wiring board assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clement, D.W.

1976-08-01

Processes of reworking printed wiring assemblies (PWA) built with multilayer printed wiring boards (MLPWB) were investigated. Because of the MLPWBs added thickness and increased heat absorption potential, assemblies built with these boards are suspected of being more susceptible to damage during component removal than assemblies built with single-layer double-sided boards. There also have been questions raised about the effect that rework has on the internal connections of the MLPWBs. A review and limited evaluation of all known rework methods resulted in selecting ''solder wick'' and ''vacuum extraction'' as the two main rework methods for use in the evaluations. The Appendixmore » defines and describes these rework techniques. Two different groups of units, intended to be representative of a wide range of proposed and presently used MLPWB-component configurations, were fabricated and then reworked by variations of these two techniques. Approximately 16,000 internal connections of MLPWBs were subjected to rework. No internal connections became open or degraded. In addition, 80 PTHs with internal connections were subjected to 10 cycles of rework to examine the effect of rework on MLPWB internal connections. Continuity of the internal connections was measured before and after all rework. Even though the rework did cause extensive external damage to the MLPWBs (blisters, measles, and land damage, for example), there was no indication of internal connection degradation. The information received thus far leads to the conclusion that internal connections of MLPWBs are not likely to be degraded as a result of assembly rework.« less

Moving Large Wiring-Harness Boards

NASA Technical Reports Server (NTRS)

Shepherd, Samuel D.; Gurman, Isaac

1990-01-01

Carrier for wiring-harness fabrication boards enables lone operator to move board easily and safely. Holds harness while operator fabricating, while being stored, and being transported to equipment frame for mounting. When positioned for assembly of wiring harness, board and carrier give operator easy and convenient access to wires and cables, when positioned for transfer of wiring harness to or from storage area, carrier holds board securely while moved by one person.

Space shuttle main engine controller assembly, phase C-D. [with lagging system design and analysis

NASA Technical Reports Server (NTRS)

1973-01-01

System design and system analysis and simulation are slightly behind schedule, while design verification testing has improved. Input/output circuit design has improved, but digital computer unit (DCU) and mechanical design continue to lag. Part procurement was impacted by delays in printed circuit board, assembly drawing releases. These are the result of problems in generating suitable printed circuit artwork for the very complex and high density multilayer boards.

The influence of temperature and humidity on printed wiring board surface finishes: Immersion tin vs organic azoles

NASA Astrophysics Data System (ADS)

Ray, U.; Artaki, I.; Gordon, H. M.; Vianco, P. T.

1994-08-01

Substitution of lead-free solders in electronic assemblies requires changes in the conventional Sn:Pb finishes on substrates and component leads to prevent contamination of the candidate lead-free solder. Options for solderability preservative coatings on the printed wiring board include organic (azole or rosin/resin based) films and tin-based plated metallic coatings. This paper compares the solderability performance and corrosion protection effectiveness of electroless tin coatings vs organic azole films after exposure to a series of humidity and thermal cycling conditions. The solderability of immersion tin is directly related to the tin oxide growth on the surface and is not affected by the formation of SnCu intermetallic phases as long as the intermetallic phase is underneath a protective Sn layer. Thin azole films decompose upon heating in the presence of oxygen and lead to solderability degradation. Evaluations of lead-free solder pastes for surface mount assembly applications indicate that immersion tin significantly improves the spreading of Sn:Ag and Sn:Bi alloys as compared to azole surface finishes.

Modular integration of electronics and microfluidic systems using flexible printed circuit boards.

PubMed

Wu, Amy; Wang, Lisen; Jensen, Erik; Mathies, Richard; Boser, Bernhard

2010-02-21

Microfluidic systems offer an attractive alternative to conventional wet chemical methods with benefits including reduced sample and reagent volumes, shorter reaction times, high-throughput, automation, and low cost. However, most present microfluidic systems rely on external means to analyze reaction products. This substantially adds to the size, complexity, and cost of the overall system. Electronic detection based on sub-millimetre size integrated circuits (ICs) has been demonstrated for a wide range of targets including nucleic and amino acids, but deployment of this technology to date has been limited due to the lack of a flexible process to integrate these chips within microfluidic devices. This paper presents a modular and inexpensive process to integrate ICs with microfluidic systems based on standard printed circuit board (PCB) technology to assemble the independently designed microfluidic and electronic components. The integrated system can accommodate multiple chips of different sizes bonded to glass or PDMS microfluidic systems. Since IC chips and flex PCB manufacturing and assembly are industry standards with low cost, the integrated system is economical for both laboratory and point-of-care settings.

Electro-optical backplane demonstrator with integrated multimode gradient-index thin glass waveguide panel

NASA Astrophysics Data System (ADS)

Schröder, Henning; Brusberg, Lars; Pitwon, Richard; Whalley, Simon; Wang, Kai; Miller, Allen; Herbst, Christian; Weber, Daniel; Lang, Klaus-Dieter

2015-03-01

Optical interconnects for data transmission at board level offer increased energy efficiency, system density, and bandwidth scalability compared to purely copper driven systems. We present recent results on manufacturing of electrooptical printed circuit board (PCB) with integrated planar glass waveguides. The graded index multi-mode waveguides are patterned inside commercially available thin-glass panels by performing a specific ion-exchange process. The glass waveguide panel is embedded within the layer stack-up of a PCB using proven industrial processes. This paper describes the design, manufacture, assembly and characterization of the first electro-optical backplane demonstrator based on integrated planar glass waveguides. The electro-optical backplane in question is created by laminating the glass waveguide panel into a conventional multi-layer electronic printed circuit board stack-up. High precision ferrule mounts are automatically assembled, which will enable MT compliant connectors to be plugged accurately to the embedded waveguide interfaces on the glass panel edges. The demonstration platform comprises a standardized sub-rack chassis and five pluggable test cards each housing optical engines and pluggable optical connectors. The test cards support a variety of different data interfaces and can support data rates of up to 32 Gb/s per channel.

Citrus Research Board-sponsored review of the University of California Riverside citrus breeding

USDA-ARS?s Scientific Manuscript database

In October 2015 the Citrus Research Board (CRB) assembled a panel of experts to review the Citrus Research Board-sponsored Citrus Research and Genetics Programs at University of California Riverside (UCR). The panel consisted of: Gennaro Fazio, USDA/ARS, Geneva, NY; Maria Angeles Forner-Giner, Insti...

Virginia Board of Education Student Code of Conduct Policy Guidelines

ERIC Educational Resources Information Center

Virginia Department of Education, 2015

2015-01-01

The Virginia Board of Education's "Student Conduct Policy Guidelines" were first developed in 1994 in response to action by the 1993 General Assembly requiring the Virginia Board of Education to establish such guidelines. In 2004, the "Guidelines" underwent a major revision in response to requirements of § 22.1-279.6. of the…

Evaluation of ENEPIG and Immersion Silver Surface Finishes Under Drop Loading

NASA Astrophysics Data System (ADS)

Pearl, Adam; Osterman, Michael; Pecht, Michael

2016-01-01

The effect of printed circuit board surface finish on the drop loading reliability of ball grid array (BGA) solder interconnects has been examined. The finishes examined include electroless nickel/electroless palladium/immersion gold (ENEPIG) and immersion silver (ImAg). For the ENEPIG finish, the effect of the Pd plating layer thickness was evaluated by testing two different thicknesses: 0.05 μm and 0.15 μm. BGA components were assembled onto the boards using either eutectic Sn-Pb or Sn-3.0Ag-0.5Cu (SAC305) solder. Prior to testing, the assembled boards were aged at 100°C for 24 h or 500 h. The boards were then subjected to multiple 1500-g drop tests. Failure analysis indicated the primary failure site for the BGAs to be the solder balls at the board-side solder interface. Cratering of the board laminate under the solder-attached pads was also observed. In all cases, isothermal aging reduced the number of drops to failure. The components soldered onto the boards with the 0.15- μm-Pd ENEPIG finish with the SAC305 solder had the highest characteristic life, at 234 drops to failure, compared with the other finish-solder combinations.

78 FR 33809 - Notification of Proposed Production Activity; Roper Corporation; Subzone 26G (Kitchen Ranges...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-05

... choose the duty rates during customs entry procedures that apply to gas and electric kitchen ranges (duty... injet assemblies, vent caps, blowers, valves, gas valves, motors, fans, control boards, light indicator assemblies, timers, light indicators, capacitors, thermistors, sensors, lamps, encoder assemblies, lenses...

Engineering Management Board Tour VAB

NASA Image and Video Library

2017-03-22

Members of NASA’s Engineering Management Board tour of the Vehicle Assembly Building at Kennedy Space Center in Florida. The platforms in High Bay 3, including the one on which the board members are standing, were designed to surround and provide access to NASA’s Space Launch System and Orion spacecraft. The Engineering Management Board toured integral areas of Kennedy to help the agencywide group reach its goal of unifying engineering work across NASA.

41 CFR 60-20.5 - Discriminatory wages.

Code of Federal Regulations, 2011 CFR

2011-07-01

... functional units: One (assembly) all female; another (wiring), all male; and a third (circuit boards), also all male. The highest wage attainable in the assembly unit is considerably less than that in the...

Demonstrating the Effect of Particle Impact Dampers on the Random Vibration Response and Fatigue Life of Printed Wiring Assemblies

NASA Technical Reports Server (NTRS)

Knight, Brent; Montgomery, Randall; Geist, David; Hunt, Ron; LaVerde, Bruce; Towner, Robert

2013-01-01

In a recent experimental study, small Particle Impact Dampers (PID) were bonded directly to the surface of printed circuit board (PCB) or printed wiring assemblies (PWA), reducing the random vibration response and increasing the fatigue life. This study provides data verifying practicality of this approach. The measured peak strain and acceleration response of the fundamental out of plane bending mode was significantly attenuated by adding a PID device. Attenuation of this mode is most relevant to the fatigue life of a PWA because the local relative displacements between the board and the supported components, which ultimately cause fatigue failures of the electrical leads of the board-mounted components are dominated by this mode. Applying PID damping at the board-level of assembly provides mitigation with a very small mass impact, especially as compared to isolation at an avionics box or shelf level of assembly. When compared with other mitigation techniques at the PWA level (board thickness, stiffeners, constrained layer damping), a compact PID device has the additional advantage of not needing to be an integral part of the design. A PID can simply be bonded to heritage or commercial off the shelf (COTS) hardware to facilitate its use in environments beyond which it was originally qualified. Finite element analysis and test results show that the beneficial effect is not localized and that the attenuation is not due to the simple addition of mass. No significant, detrimental reduction in frequency was observed. Side-by-side life testing of damped and un-damped boards at two different thicknesses (0.070" and 0.090") has shown that the addition of a PID was much more significant to the fatigue life than increasing the thickness. High speed video, accelerometer, and strain measurements have been collected to correlate with analytical results.

Unitary Shaft-Angle and Shaft-Speed Sensor Assemblies

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.; Howard, David E.; Smith, Dennis A.

2006-01-01

The figure depicts a unit that contains a rotary-position or a rotary-speed sensor, plus electronic circuitry necessary for its operation, all enclosed in a single housing with a shaft for coupling to an external rotary machine. This rotation sensor unit is complete: when its shaft is mechanically connected to that of the rotary machine and it is supplied with electric power, it generates an output signal directly indicative of the rotary position or speed, without need for additional processing by other circuitry. The incorporation of all of the necessary excitatory and readout circuitry into the housing (in contradistinction to using externally located excitatory and/or readout circuitry) in a compact arrangement is the major difference between this unit and prior rotation-sensor units. The sensor assembly inside the housing includes excitatory and readout integrated circuits mounted on a circular printed-circuit board. In a typical case in which the angle or speed transducer(s) utilize electromagnetic induction, the assembly also includes another circular printed-circuit board on which the transducer windings are mounted. A sheet of high-magnetic permeability metal ("mu metal") is placed between the winding board and the electronic-circuit board to prevent spurious coupling of excitatory signals from the transducer windings to the readout circuits. The housing and most of the other mechanical hardware can be common to a variety of different sensor designs. Hence, the unit can be configured to generate any of variety of outputs by changing the interior sensor assembly. For example, the sensor assembly could contain an analog tachometer circuit that generates an output proportional (in both magnitude and sign or in magnitude only) to the speed of rotation.

Mechanism controller system for the optical spectroscopic and infrared remote imaging system instrument on board the Rosetta space mission

NASA Astrophysics Data System (ADS)

Castro Marín, J. M.; Brown, V. J. G.; López Jiménez, A. C.; Rodríguez Gómez, J.; Rodrigo, R.

2001-05-01

The optical, spectroscopic infrared remote imaging system (OSIRIS) is an instrument carried on board the European Space Agency spacecraft Rosetta that will be launched in January 2003 to study in situ the comet Wirtanen. The electronic design of the mechanism controller board (MCB) system of the two OSIRIS optical cameras, the narrow angle camera, and the wide angle camera, is described here. The system is comprised of two boards mounted on an aluminum frame as part of an electronics box that contains the power supply and the digital processor unit of the instrument. The mechanisms controlled by the MCB for each camera are the front door assembly and a filter wheel assembly. The front door assembly for each camera is driven by a four phase, permanent magnet stepper motor. Each filter wheel assembly consists of two, eight filter wheels. Each wheel is driven by a four phase, variable reluctance stepper motor. Each motor, for all the assemblies, also contains a redundant set of four stator phase windings that can be energized separately or in parallel with the main windings. All stepper motors are driven in both directions using the full step unipolar mode of operation. The MCB also performs general housekeeping data acquisition of the OSIRIS instrument, i.e., mechanism position encoders and temperature measurements. The electronic design application used is quite new due to use of a field programmable gate array electronic devices that avoid the use of the now traditional system controlled by microcontrollers and software. Electrical tests of the engineering model have been performed successfully and the system is ready for space qualification after environmental testing. This system may be of interest to institutions involved in future space experiments with similar needs for mechanisms control.

A Motor Drive Electronics Assembly for Mars Curiosity Rover: An Example of Assembly Qualification for Extreme Environments

NASA Technical Reports Server (NTRS)

Kolawa, Elizabeth; Chen, Yuan; Mojarradi, Mohammad M.; Weber, Carissa Tudryn; Hunter, Don J.

2013-01-01

This paper describes the technology development and infusion of a motor drive electronics assembly for Mars Curiosity Rover under space extreme environments. The technology evaluation and qualification as well as space qualification of the assembly are detailed and summarized. Because of the uncertainty of the technologies operating under the extreme space environments and that a high level reliability was required for this assembly application, both component and assembly board level qualifications were performed.

Engineering Management Board Tour VAB

NASA Image and Video Library

2017-03-22

Members of NASA’s Engineering Management Board visit the Vehicle Assembly Building’s High Bay 3 at Kennedy Space Center in Florida. The platforms in High Bay 3, including the one on which the board members are standing, were designed to surround and provide access to NASA’s Space Launch System and Orion spacecraft. The Engineering Management Board toured integral areas of Kennedy to help the agencywide group reach its goal of unifying engineering work across NASA.

Infrared Thermal Testing Of Mechanical Assemblies At The Military Depot And Field Level: A Progress Report

NASA Astrophysics Data System (ADS)

Kaplan, Herbert

1988-01-01

Based on encouraging results on the Army's programs for infrared mass screening of printed circuit boards at the depot level, the US Army CECOM (Communication-Electronics Command) undertook a one-year investigation of the applicability of similar techniques to screening and diagnostics of mechanical assemblies. These included tanks, helicopters, transport vehicles and their major subassemblies (transmissions, engines, axles, etc.) at field and depot levels. Honeyhill Technical Company was tasked to classify candidate assemblies and perform preliminary measurements using Army-owned general-purpose thermal imaging equipment. The investigations yielded positive results, and it was decided to pursue a comprehensive measurements program using field-mobile equipment specifically procured for the program. This paper summarizes the results of the investigations, outlines the measurements techniques utilized, describes the classification and selection of candidate assemblies, and reports on progress toward the goals of the program.

Lead free 0201 assembly and thermal cycle/aging reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza; Ramkumar, S. Manian; Varanasi, Arun

2005-01-01

The many challenges with 0201 passive component assembly can be attributed to the solder paste volume, pad design, aperture design, board finish, type of solder paste, pick-and-place, and reflow profile. A Design-of-Experiment (DOE) study was carried out to investigate the effects of these parameters on assembly defects and reliability.

4 channels x 10-Gbps optoelectronic transceiver based on silicon optical bench technology

NASA Astrophysics Data System (ADS)

Chen, Chin T.; Hsiao, Hsu L.; Chang, Chia. C.; Shen, Po K.; Lu, Guan F.; Lee, Yun C.; Chang, Shou F.; Lin, Yo S.; Wu, Mount L.

2012-01-01

In this paper, a bi-directional 4-channel x 10-Gbps optoelectronic transceiver based on this silicon optical bench (SiOB) technology is developed. A bi-directional optical sub-assembly (BOSA), fiber ribbon assembly, PCB with high frequency trace design, transmitter driver, and receiver TIA IC are included in this transceiver. The BOSA and PCB also have some specific design for conventional chip-on-board (COB) process. In eye diagram measurement, the transmitter can pass 10-G Ethernet eye mask with 25% margin at room temperature; Bit-error-rate (BER) performance from the transmitter to receiver via 10-meter fiber can achieve 10-12 order, which confirm the transceiver's ability of 10-Gbps data transmission per a channel.

3-D Packaging: A Technology Review

NASA Technical Reports Server (NTRS)

Strickland, Mark; Johnson, R. Wayne; Gerke, David

2005-01-01

Traditional electronics are assembled as a planar arrangement of components on a printed circuit board (PCB) or other type of substrate. These planar assemblies may then be plugged into a motherboard or card cage creating a volume of electronics. This architecture is common in many military and space electronic systems as well as large computer and telecommunications systems and industrial electronics. The individual PCB assemblies can be replaced if defective or for system upgrade. Some applications are constrained by the volume or the shape of the system and are not compatible with the motherboard or card cage architecture. Examples include missiles, camcorders, and digital cameras. In these systems, planar rigid-flex substrates are folded to create complex 3-D shapes. The flex circuit serves the role of motherboard, providing interconnection between the rigid boards. An example of a planar rigid - flex assembly prior to folding is shown. In both architectures, the interconnection is effectively 2-D.

Engineering Management Board Tour VAB

NASA Image and Video Library

2017-03-22

The view members of NASA’s Engineering Management Board had in looking up the Vehicle Assembly Building’s High Bay 3 at Kennedy Space Center in Florida. The platforms in High Bay 3, including the one on which the board members are standing, were designed to surround and provide access to NASA’s Space Launch System and Orion spacecraft. The Engineering Management Board toured integral areas of Kennedy to help the agencywide group reach its goal of unifying engineering work across NASA.

Engineering Management Board Tour VAB

NASA Image and Video Library

2017-03-22

Members of NASA’s Engineering Management Board pause for a group photo during a tour of the Vehicle Assembly Building at Kennedy Space Center in Florida. The platforms in High Bay 3, including the one on which the board members are standing, were designed to surround and provide access to NASA’s Space Launch System and Orion spacecraft. The Engineering Management Board toured integral areas of Kennedy to help the agencywide group reach its goal of unifying engineering work across NASA.

The on-board tailpipe emissions measurement system (TOTEMS) : proof\\0x2010 of\\0x2010concept.

DOT National Transportation Integrated Search

2009-06-03

An on-board tailpipe emissions instrumentation system was designed, assembled and tested as proof-of-concept : for the University of Vermonts Transportation Research Center (TRC) Signature Project #2 real-world vehicle : emissions data colle...

7 CFR 982.39 - Duties.

Code of Federal Regulations, 2010 CFR

2010-01-01

... investigate the growing, shipping and marketing conditions with respect to hazelnuts, and assemble data in... of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... the Board at least once for each marketing year and at such other times as the Board deems necessary...

7 CFR 981.39 - Duties.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Almond Board of California § 981.39 Duties. The Board shall have, among other things, the... growing, shipping, and marketing conditions with respect to almonds and to assemble data in connection...

7. View of DR 3 antenna typical front stay concrete ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. View of DR 3 antenna typical front stay concrete showing embedment anchors, foundation steel base plate, vertical member with small diameter turnbuckles, antenna assembly in background, and story board for scale. - Clear Air Force Station, Ballistic Missile Early Warning System Site II, One mile west of mile marker 293.5 on Parks Highway, 5 miles southwest of Anderson, Anderson, Denali Borough, AK

STS-34 onboard view of iodine comparator assembly used to check water quality

NASA Technical Reports Server (NTRS)

1989-01-01

STS-34 closeup view taken onboard Atlantis, Orbiter Vehicle (OV) 104, is of the iodine comparator assembly. Potable water quality is checked by comparing the water color to the color chart on the surrounding board.

Electronic inverter assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Brij N.; Schmit, Christopher J.

A first driver portion comprises a set of first components mounted on or associated with a first circuit board. A second circuit board is spaced apart from the first circuit board. A second driver portion comprises a set of second components mounted on or associated with the second circuit board, where the first driver portion and the second driver portion collectively are adapted to provide input signals to the control terminal of each semiconductor switch of an inverter. A first edge connector is mounted on the first circuit board. A second edge connector is mounted on the second circuit board.more » An interface board has mating edges that mate with the first edge connector and the second edge connector.« less

47 CFR 2.925 - Identification of equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... sections assembled in a common enclosure, on a common chassis or circuit board, and with common frequency controlling circuits. Devices to which a single FCC Identifier has been assigned shall be identified pursuant... circuit boards with independent frequency controlling circuits. The FCC Identifier assigned to any...

Requirements for conformal coating and staking of printed wiring boards and electronic assemblies

NASA Technical Reports Server (NTRS)

1985-01-01

In order to maintain the high standards of the NASA conformal coating and staking program, this publication: prescribes NASA's requirements for assuring reliable conformal coating and staking for printed wiring boards and electronic assemblies; describes and incorporates basic considerations necessary to assure reliable conformal coating and staking; establishes the supplier's responsibility to train and certify personnel; provides for supplier documentation of the fabrication and inspection procedures to be used for NASA work, including supplier innovations and changes in technology; and provides visual workmanship standards to aid those responsible for determining quality conformance to the established requirements.

Development and user evaluation of a virtual rehabilitation system for wobble board balance training.

PubMed

Fitzgerald, Diarmaid; Trakarnratanakul, Nanthana; Dunne, Lucy; Smyth, Barry; Caulfield, Brian

2008-01-01

We have developed a prototype virtual reality-based balance training system using a single inertial orientation sensor attached to the upper surface of a wobble board. This input device has been interfaced with Neverball, an open source computer game to create the balance training platform. Users can exercise with the system by standing on the wobble board and tilting it in different directions to control an on-screen environment. We have also developed a customized instruction manual to use when setting up the system. To evaluate the usability our prototype system we undertook a user evaluation study with twelve healthy novice participants. Participants were required to assemble the system using an instruction manual and then perform balance exercises with the system. Following this period of exercise VRUSE, a usability evaluation questionnaire, was completed by participants. Results indicated a high level of usability in all categories evaluated.

Illinois Junior College Board Biennial Report, 1971-1972, to the Governor and the Members of the Illinois General Assembly. Report No. D-750.

ERIC Educational Resources Information Center

Illinois Community Coll. Board, Springfield.

This biennial report of the Illinois Junior College Board contains data on the community college program during 1971 and 1972. The report discusses the following topics: Selected Data of Illinois Public Junior Colleges; Organization of Higher Education in Illinois; Highlights of the Activities of the Illinois Junior College Board in 1971 and 1972;…

Using On-Line Bulletin Boards to Gather Preliminary Information

ERIC Educational Resources Information Center

Kelley, Kathleen; Govindasamy, Ramu; Hyde, Jeffrey

2012-01-01

Internet bulletin-board sessions can be used to collect preliminary, qualitative data. This method allows Extension personnel to gather responses from stakeholders about potential programming, consumer needs and desires, and preference for program delivery method without assembling participants in one location. Several other advantages exist,…

STS-5 crewmembers with meal tray assembly on middeck

NASA Technical Reports Server (NTRS)

1982-01-01

Commander Brand (in dark blue shirt), Pilot Overmyer (left), and Mission Specialist (MS) Lenoir (right) conduct microgravity experiments with food containers and meal tray assemblies in front of middeck port side wall and side hatch. Brand prepares to eat as meal tray assembly floats above his chest and Overmeyer and Lenoir look on. Sign on port side wall is labeled STS-5 Message Board.

Fast wire per wire X-ray data acquisition system for time-resolved small angle scattering experiments

NASA Astrophysics Data System (ADS)

Epstein, A.; Briquet-Laugier, F.; Sheldon, S.; Boulin, C.

2000-04-01

Most of the X-ray multi-wire gas detectors used at the EMBL Hamburg outstation for time-resolved studies of biological samples are readout, using the delay line method. The main disadvantage of such readout systems is their event rate limitation introduced by the delay line and the required time to digital conversion step. They also lack the possibility to deal with multiple events. To overcome these limitations, a new approach for the complete readout system was introduced. The new linear detection system is based on the wire per wire approach where each individual wire is associated to preamplifier/discriminator/counter electronics channel. High-density, front-end electronics were designed around a fast current sensitive preamplifier. An eight-channel board was designed to include the preamplifiers-discriminators and the differential ECL drivers output stages. The detector front-end consists of 25 boards directly mounted inside the detector assembly. To achieve a time framing resolution as short as 10 /spl mu/s, very fast histogramming is required. The only way to implement this for a high number of channels (200 in our case) is by using a distributed system. The digital part of the system consists of a crate controller, up to 16 acquisition boards (capable of handling fast histogramming for up to 32-channels each) and an optical-link board (based on the Cypress "Hot-Link" chip set). Both the crate controller and the acquisition boards are based on a standard RISC microcontroller (IDT R3081) plug-in board. At present, a dedicated CAMAC module which we developed is used to interface the digital front-end acquisition crate to the host via the optical link.

Evaluation of test equipment for the detection of contamination on electronic circuits

NASA Astrophysics Data System (ADS)

Bergendahl, C. G.; Dunn, B. D.

1984-08-01

The reproducibility, sensitivity and ease of operation of test equipment for the detection of ionizable contaminants on the surface of printed circuit assemblies were assessed. The characteristics of the test equipment are described. Soldering fluxes were chosen as contaminants and were applied in controlled amounts to printed-circuit board assemblies possessing two different component populations. Results show that the relationship between equipment readings varies with flux type. Each kind of test equipment gives a good measure of board cleanliness, although reservations exist concerning the interpretation of such results. A test method for the analysis of total (organic and inorganic) halides in solder fluxes is presented.

Assembly room, bunkhouse first floor interior. Vent pipe for missing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Assembly room, bunkhouse first floor interior. Vent pipe for missing heating stove exited through opening into chimney, seen on the far wall. Walls are exposed studs and bracing with board and battan on the exterior and interior sides. - Sespe Ranch, Bunkhouse, 2896 Telegraph Road, Fillmore, Ventura County, CA

Cleaning of printed circuit assemblies with surface-mounted components

NASA Astrophysics Data System (ADS)

Arzigian, J. S.

The need for ever-increasing miniaturization of airborne instrumentation through the use of surface mounted components closely placed on printed circuit boards highlights problems with traditional board cleaning methods. The reliability of assemblies which have been cleaned with vapor degreasing and spray cleaning can be seriously compromised by residual contaminants leading to solder joint failure, board corrosion, and even electrical failure of the mounted parts. In addition, recent government actions to eliminate fully halogenated chlorofluorocarbons (CFC) and chlorinated hydrocarbons from the industrial environment require the development of new cleaning materials and techniques. This paper discusses alternative cleaning materials and techniques and results that can be expected with them. Particular emphasis is placed on problems related to surface-mounted parts. These new techniques may lead to improved circuit reliability and, at the same time, be less expensive and less environmentally hazardous than the traditional systems.

78 FR 30269 - Foreign-Trade Zone 129-Bellingham, Washington; Authorization of Production Activity; T.C. Trading...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-22

... proposed production activity to the Foreign-Trade Zones (FTZ) Board on behalf of T.C. Trading Company, Inc... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-8-2013] Foreign-Trade Zone 129--Bellingham, Washington; Authorization of Production Activity; T.C. Trading Company, Inc. (Eyeglass Assembly and Kitting...

Measure Guideline: Three High Performance Mineral Fiber Insulation Board Retrofit Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neuhauser, K.

2015-01-01

This Measure Guideline describes a high performance enclosure retrofit package that uses mineral fiber insulation board, and is intended to serve contractors and designers seeking guidance for non-foam exterior insulation retrofit processes. The guideline describes retrofit assembly and details for wood frame roof and walls and for cast concrete foundations.

78 FR 75360 - Notice of Issuance of Final Determination Concerning Certain Ethernet Switches

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-11

... printed circuit board assembly (``PCBA''), chassis, top cover, power supply, and fans. The switches... printed circuit board is populated with various electronic components to make a PCBA. 2. The PCBA is... Singapore. You argue that without the EOS software, the units exported from Singapore lack the intelligence...

Flight Model of the `Flying Laptop' OBC and Reconfiguration Unit

NASA Astrophysics Data System (ADS)

Eickhoff, Jens; Stratton, Sam; Butz, Pius; Cook, Barry; Walker, Paul; Uryu, Alexander; Lengowski, Michael; Roser, Hans-Peter

2012-08-01

As already published in papers at the DASIA conferences 2010 in Budapest [1] and 2011 in Malta [2], the University of Stuttgart, Germany, is developing an advanced 3-axis stabilized small satellite applying industry standards for command/control techniques, onboard software design and onboard computer components. The satellite has a launch mass of approx. 120kg. One of the main challenges was the development of an ultra compact and performing onboard computer (OBC), which was intended to support an RTEMS operating system, a PUS standard based onboard software (OBSW) and CCSDS standard based ground/space communication. The developed architecture is based on 4 main elements (see [1, 2] and Figure 3) which are developed in cooperation with industrial partners:• the OBC core board based on the LEON3 FT architecture,• an I/O Board for all OBC digital interfaces to S/C equipment,• a CCSDS TC/TM decoder/encoder board,• reconfiguration unit being embedded in the satellite power control and distribution unit PCDU.In the meantime the EM / Breadboard units of the computer have been tested intensively including first HW/SW integration tests in a Satellite Testbench (see Figure 2). The FM HW elements from the co-authoring suppliers are under assembly in Stuttgart.

The Committee Studying Contagious Disease Training for Public Safety Personnel. Report of the Committee on Training of the Criminal Justice Services Board to the Governor and the General Assembly of Virginia. House Document No. 15.

ERIC Educational Resources Information Center

Virginia State Dept. of Criminal Justice Services, Richmond.

Through discussion and extensive research, the Committee Studying Contagious Disease Training attempted to address concerns regarding education and training of public safety personnel with regard to human immunodeficiency virus (HIV) and hepatitis B virus (HBV). The committee's findings were based on Occupational Safety and Health Administration…

A Study on the Thermomechanical Reliability Risks of Through-Silicon-Vias in Sensor Applications

PubMed Central

Shao, Shuai; Liu, Dapeng; Niu, Yuling; O’Donnell, Kathy; Sengupta, Dipak; Park, Seungbae

2017-01-01

Reliability risks for two different types of through-silicon-vias (TSVs) are discussed in this paper. The first is a partially-filled copper TSV, if which the copper layer covers the side walls and bottom. A polymer is used to fill the rest of the cavity. Stresses in risk sites are studied and ranked for this TSV structure by FEA modeling. Parametric studies for material properties (modulus and thermal expansion) of TSV polymer are performed. The second type is a high aspect ratio TSV filled by polycrystalline silicon (poly Si). Potential risks of the voids in the poly Si due to filling defects are studied. Fracture mechanics methods are utilized to evaluate the risk for two different assembly conditions: package assembled to printed circuit board (PCB) and package assembled to flexible substrate. The effect of board/substrate/die thickness and the size and location of the void are discussed. PMID:28208758

Measure Guideline: Three High Performance Mineral Fiber Insulation Board Retrofit Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neuhauser, Ken

2015-01-01

This Measure Guideline describes a high performance enclosure retrofit package that uses mineral fiber insulation board. The Measure Guideline describes retrofit assembly and details for wood frame roof and walls and for cast concrete foundations. This Measure Guideline is intended to serve contractors and designers seeking guidance for non-foam exterior insulation retrofit.

Fire resistance of engineered wood rim board products.

Treesearch

Robert H. White

2003-01-01

Engineered wood products, such as oriented strandboard, laminated veneer lumber, and other composite wood products, are being used more often in construction. This includes use as rim boards, which are the components around the perimeter of a floor assembly. This situation has increased the need for information about the fire resistance of these products. In this study...

Developing Planetary Protection Technology: Microbial Diversity and Radiation Resistance of Microorganisms in a Spacecraft Assembly Facility.

NASA Astrophysics Data System (ADS)

Chen, F.; La Duc, M. T.; Baker, A.; Koukol, R.; Barengoltz, J.; Kern, R.; Venkateswaran, K.

2001-12-01

Europa has attracted much attention as evidence suggests the presence of a liquid ocean beneath this Jupiter moon's frozen crust. Such an environment might be conducive to the origins of life. Since robotic exploration of Europa is being planned, it becomes crucial to prepare for bio-burden reduction of hardware assembled for Europa missions to avoid contamination of Europa's pristine environment. In this study, we examined the microbial diversity of samples collected from two flight-ready circuit boards and their assembly facility. Also, because Jupiter's strong radiation environment may be able to reduce the viable microbial contamination on flight components, we have also studied the effects of radiation on microbial communities found to be associated with the space-flight hardware and/or present in the assembly facility. Surface samples thought to be representative of considerable human contact were collected from two circuit boards and various locations within the assembly facility using polyester swabs (swab samples). Likewise, sterile wipes were used to sample a shelf above the workstation where the circuit boards were assembled and the floor of the facility (wipe samples). The swab and wipe samples were pooled separately and divided into two halves, one of which was irradiated with 1Mrad gamma radiation for 5.5 hours, the other was not irradiated. About 1.2x104 and 6x104 CFUs/m2 cultivable microbes were detected in the swab and wipe samples, respectively. Radiation proved effective in inhibiting the growth of most microbes. Further characterization of the bacterial colonies observed in the irradiated swab and wipe samples is necessary to determine the degree of the radiation resistance. The16S rDNA sequence analysis of the cultivable microbes indicated that the assembly facility consists mostly of the members of actinobacteria, corynebacteria and pseudomonads. However, the swab samples that include the circuit boards were predominantly populated with Bacillus and Staphylococcus. Molecular microbial diversity was also studied by cloning the 16S rDNA PCR fragment from the samples. The non-irradiated swab samples were largely populated by species of Exiguobacter and Bacillus whereas the irradiated swab samples were dominated by Bacillus and E. coli. Radiation damage of microorganisms was also investigated by epifluorescence microscopy. In summary, our study has shown that gamma radiation can inhibit the growth of most of the cultivable microbes, but preliminary results suggest that radiation such as this has little adverse effect on the DNA molecules of these microorganisms.

ISS Microgravity Environment

NASA Technical Reports Server (NTRS)

Laible, Michael R.

2011-01-01

The Microgravity performance assessment of the International Space Station (ISS) is comprised of a quasi-steady, structural dynamic and a vibro-acoustic analysis of the ISS assembly-complete vehicle configuration. The Boeing Houston (BHOU) Loads and Dynamics Team is responsible to verify compliance with the ISS System Specification (SSP 41000) and USOS Segment (SSP 41162) microgravity requirements. To verify the ISS environment, a series of accelerometers are on-board to monitor the current environment. This paper summarizes the results of the analysis that was performed for the Verification Analysis Cycle (VAC)-Assembly Complete (AC) and compares it to on-orbit acceleration values currently being reported. The analysis will include the predicted maximum and average environment on-board ISS during multiple activity scenarios

Full-Scale Experimental Investigation to Quantify Building Component Ignition Vulnerability from Mulch Beds Attacked by Firebrand Showers.

PubMed

Manzello, Samuel L; Suzuki, Sayaka; Nii, Daisaku

2017-03-01

Structure ignition by wind-driven firebrand showers is an important fire spread mechanism in large outdoor fires. Experiments were conducted with three common mulch types (shredded hardwood mulch, Japanese Cypress wood chips, and pine bark nuggets) placed adjacent to realistic-scale reentrant corners. In the first series of experiments, mulch beds were placed adjacent to a re-entrant corner constructed with wood studs and lined with oriented strand board (OSB) as the sheathing. The premise behind conducting experiments with no siding treatments applied was predicated on the notion that bare OSB mulch contact would be a worst-case scenario, and therefore, a wall assembly in the most vulnerable state to mulch ignition. In the second series of experiments, vinyl siding was applied to the re-entrant corner assemblies (wood studs/OSB/moisture barrier/vinyl siding), and the influence of vertical separation distance (102 mm or 203 mm) on wall ignition from adjacent mulch beds was determined. The vertical separation distance was maintained by applying gypsum board to the base of the re-entrant corner. The siding itself did not influence the ignition process for the mulch beds, as the mulch beds were the first to ignite from the firebrand showers. In all experiments, it was observed that firebrands produced smoldering ignition in the mulch beds, this transitioned to flaming ignition, and the re-entrant corner assembly was exposed to the flaming mulch beds. With no siding treatments applied, the flaming mulch beds ignited the re-entrant corner, and ignition was observed to propagate to the back side of re-entrant corner assembly under all wind speeds (6 m/s to 8 m/s). With respect to the re-entrant corners fitted with vinyl siding, the mulch type, vertical separation distance, and wind speed were important parameters as to whether flaming ignition was observed to propagate to the back-side of a reentrant corner assembly. Mulches clearly pose an ignition hazard to structures in large outdoor fires.

Report, 1979-1980: Assembly of Life Sciences, National Research Council.

ERIC Educational Resources Information Center

National Academy of Sciences - National Research Council, Washington, DC. Assembly of Life Sciences.

This annual report of the Assembly of Life Sciences (ALS) covers the fiscal year beginning July 1, 1979, and ending June 30, 1980. The report has four major sections: (1) Special Programs of the Executive Office; (2) Division of Biological Sciences; (3) Division of Medical Sciences; and (4) Board on Toxicology and Environmental Health Hazards.…

1978-1979 Report: Assembly of Life Sciences, National Research Council.

ERIC Educational Resources Information Center

National Academy of Sciences, Washington, DC.

This annual report of the Assembly of Life Sciences (ALS) covers the fiscal year from July 1, 1978 to June 30, 1979. The report has four major sections: (1) Special Programs of the Executive Office; (2) Division of Biological Sciences; (3) Division of Medical Sciences; and (4) Board on Toxicology and Environmental Health Hazards. The activities…

Board of Governors' Recommendations: FY 2007-09 Biennial Capital Budget and Five-Year Plans

ERIC Educational Resources Information Center

Connecticut Department of Higher Education (NJ1), 2006

2006-01-01

In accordance with the Connecticut General Statutes Sec. 10a-6 and 10a-8, the Board of Governors' prepares and presents to the Governor and General Assembly a consolidated capital budget request and five-year plan with recommendations for public higher education. Through passage of the UConn 2000 legislation, the University of Connecticut…

Supporting and Staffing High-Needs Schools: Recommendations from South Carolina's National Board Certified Teachers[R

ERIC Educational Resources Information Center

Berry, Barnett; Rasberry, Melissa; Byrd, Ann

2007-01-01

On August 5, 2006, more than 300 South Carolina National Board Certified Teachers[R] (NBCTs) assembled in Columbia at a policy summit to address the vexing problem of recruiting and retaining accomplished teachers in high-needs schools. Before this summit, the NBCTs read a number of background papers and research summaries. During the summit, they…

Annual Joint Report on Pre-Kindergarten through Higher Education in Tennessee, 2013

ERIC Educational Resources Information Center

Tennessee State Board of Education, 2013

2013-01-01

This paper complies with the requirements established in T.C.A. Section 49-1-302(a)(10). The act directs the State Board of Education and the Tennessee Higher Education Commission to provide a report to the Governor and General Assembly, all public schools, and institutions of higher learning and their respective boards. This report is to include,…

Design, Assembly, Integration, and Testing of a Power Processing Unit for a Cylindrical Hall Thruster, the NORSAT-2 Flatsat, and the Vector Gravimeter for Asteroids Instrument Computer

NASA Astrophysics Data System (ADS)

Svatos, Adam Ladislav

This thesis describes the author's contributions to three separate projects. The bus of the NORSAT-2 satellite was developed by the Space Flight Laboratory (SFL) for the Norwegian Space Centre (NSC) and Space Norway. The author's contributions to the mission were performing unit tests for the components of all the spacecraft subsystems as well as designing and assembling the flatsat from flight spares. Gedex's Vector Gravimeter for Asteroids (VEGA) is an accelerometer for spacecraft. The author's contributions to this payload were modifying the instrument computer board schematic, designing the printed circuit board, developing and applying test software, and performing thermal acceptance testing of two instrument computer boards. The SFL's cylindrical Hall effect thruster combines the cylindrical configuration for a Hall thruster and uses permanent magnets to achieve miniaturization and low power consumption, respectively. The author's contributions were to design, build, and test an engineering model power processing unit.

Investigation into the High Voltage Shutdown of the Oxygen Generator System in the International Space Station

NASA Technical Reports Server (NTRS)

Carpenter, Joyce E.; Gentry, Gregory J.; Diderich, Greg S.; Roy, Robert J.; Golden, John L.; VanKeuren, Steve; Steele, John W.; Rector, Tony J.; Varsik, Jerome D.; Montefusco, Daniel J.;

Command and Telemetry Latency Effects on Operator Performance during International Space Station Robotics Operations

NASA Technical Reports Server (NTRS)

Currie, Nancy J.; Rochlis, Jennifer

2004-01-01

International Space Station (ISS) operations will require the on-board crew to perform numerous robotic-assisted assembly, maintenance, and inspection activities. Current estimates for some robotically performed maintenance timelines are disproportionate and potentially exceed crew availability and duty times. Ground-based control of the ISS robotic manipulators, specifically the Special Purpose Dexterous Manipulator (SPDM), is being examined as one potential solution to alleviate the excessive amounts of crew time required for extravehicular robotic maintenance and inspection tasks.

High-gain cryogenic amplifier assembly employing a commercial CMOS operational amplifier.

PubMed

Proctor, J E; Smith, A W; Jung, T M; Woods, S I

2015-07-01

We have developed a cryogenic amplifier for the measurement of small current signals (10 fA-100 nA) from cryogenic optical detectors. Typically operated with gain near 10(7) V/A, the amplifier performs well from DC to greater than 30 kHz and exhibits noise level near the Johnson limit. Care has been taken in the design and materials to control heat flow and temperatures throughout the entire detector-amplifier assembly. A simple one-board version of the amplifier assembly dissipates 8 mW to our detector cryostat cold stage, and a two-board version can dissipate as little as 17 μW to the detector cold stage. With current noise baseline of about 10 fA/(Hz)(1/2), the cryogenic amplifier is generally useful for cooled infrared detectors, and using blocked impurity band detectors operated at 10 K, the amplifier enables noise power levels of 2.5 fW/(Hz)(1/2) for detection of optical wavelengths near 10 μm.

Integrated photodiodes complement the VCSEL platform

NASA Astrophysics Data System (ADS)

Grabherr, Martin; Gerlach, Philipp; King, Roger; Jäger, Roland

2009-02-01

Many VCSEL based applications require optical feedback of the emitted light. E.g. light output monitor functions in transceivers are used to compensate for thermally induced power variation, power degradation, or even breakdown of pixels if logic for redundancy is available. In this case integrated photodiodes offer less complex assembly compared to widely used hybrid solutions, e.g. known in LC-TOSA assemblies. Especially for chip-on-board (COB) assembly and array configurations, integrated monitor diodes offer a simple and compact power monitoring possibility. For 850 nm VCSELs the integrated photodiodes can be placed between substrate and bottom-DBR, on top of the top-DBR, or inbetween the layer sequence of one DBR. Integrated intra-cavity photodiodes offer superior characteristics in terms of reduced sensitivity for spontaneously emitted light [1] and thus are very well suited for power monitoring or even endof- life (EOL) detection. We present an advanced device design for an intra-cavity photodiode and according performance data in comparison with competing approaches.

Miniature housing with standard addressable interface for smart sensors and drive electronics

NASA Technical Reports Server (NTRS)

Howard, David E. (Inventor); Smith, Dennis A. (Inventor); Alhorn, Dean C. (Inventor)

2006-01-01

A miniature assembly is disclosed which includes a housing assembly with a cover configured to be sealably secured to a box-like receptacle. The receptacle comprises openings on opposing sides for the seating therein of communications connectors. Enclosed within housing is custom-sized circuit board for supporting, at least, a standard communications interface and at least one electronic device.

Whisker Formation on SAC305 Soldered Assemblies

NASA Astrophysics Data System (ADS)

Meschter, S.; Snugovsky, P.; Bagheri, Z.; Kosiba, E.; Romansky, M.; Kennedy, J.; Snugovsky, L.; Perovic, D.

2014-11-01

This article describes the results of a whisker formation study on SAC305 assemblies, evaluating the effects of lead-frame materials and cleanliness in different environments: low-stress simulated power cycling (50-85°C thermal cycling), thermal shock (-55°C to 85°C), and high temperature/high humidity (85°C/85% RH). Cleaned and contaminated small outline transistors, large leaded quad flat packs (QFP), plastic leaded chip carrier packages, and solder balls with and without rare earth elements (REE) were soldered to custom designed test boards with Sn3Ag0.5Cu (SAC305) solder. After assembly, all the boards were cleaned, and half of them were recontaminated (1.56 µg/cm2 Cl-). Whisker length, diameter, and density were measured. Detailed metallurgical analysis on components before assembly and on solder joints before and after testing was performed. It was found that whiskers grow from solder joint fillets, where the thickness is less than 25 µm, unless REE was present. The influence of lead-frame and solder ball material, microstructure, cleanliness, and environment on whisker characteristics is discussed. This article provides detailed metallurgical observations and select whisker length data obtained during this multiyear testing program.

Single Circuit Board Implementation of a Digitally Compensated SAW Oscillator (DCSO).

DTIC Science & Technology

1983-12-01

Through this project a design for a Digitally Compensated SAW Oscillator (DCSO) was developed and implemented on a single circuit board. The AFIT IC, which...is the heart of the design , did not function properly. Therefore, my work was halted after testing several of the subcircuits and assembling the...o.... -7 Standards ........ o..o....... -8 Approach-9 Sequence of Presentation .................. -10 II, Design

An Indiana Pattern for Higher Education: Report of the State Policy Commission on Post High School Education.

ERIC Educational Resources Information Center

Indiana State Policy Commission on Post High School Education, Indianapolis.

The commission recommended: (1) establishment by the General Assembly of a Board of Regents; (2) number and terms of Board members; (3) setting the Regent's duties as (a) setting policy for public higher education, (b) making long-range plans in coordination with private schools, (c) approving new schools and major changes of policy, (d)…

Illinois Community College Board FY 2004 Adult Education and Family Literacy Report to the Governor and General Assembly

ERIC Educational Resources Information Center

Illinois Community College Board, 2004

2004-01-01

The Illinois Community College Board (ICCB) continues its commitment to expand Adult Education and Family Literacy programs necessary for individuals and families to have a high quality work and life in Illinois. This report provides a summary of ICCB programs and activities in adult education and family literacy during the fiscal year July 1,…

Incentives for Improving Undergraduate Teaching in the California Community Colleges. A Report to the Chancellor's Office on Assembly Concurrent Resolution (ACR) 39, Hayden.

ERIC Educational Resources Information Center

McHargue, Michael

This report details the response of the Board of Governors of the California Community Colleges to Assembly Concurrent Resolution (ACR) Number 39 (Hayden), known as "Incentives for Improving Undergraduate Teaching." Part 1 provides the background and recent history of community college faculty development. Part 2 describes the current faculty…

Push plate, mounting assembly, circuit board, and method of assembling thereof for ball grid array packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaughn, Mark R.; Montague, Stephen

A push plate that includes springs in the form of cantilever flexures and an inspection window is disclosed. The push plate provides a known, uniform, down force and minimal torque to a package to be tested. The cantilevers have a known, calculable down force producing stiffness. The window provides for viewing of the package during testing.

Reliability of CGA/LGA/HDI Package Board/Assembly (Final Report)

NASA Technical Reports Server (NTRS)

Ghaffaroam. Reza

2014-01-01

Package manufacturers are now offering commercial-off-the-shelf column grid array (COTS CGA) packaging technologies in high-reliability versions. Understanding the process and quality assurance (QA) indicators for reliability are important for low-risk insertion of these advanced electronics packages. The previous reports, released in January of 2012 and January of 2013, presented package test data, assembly information, and reliability evaluation by thermal cycling for CGA packages with 1752, 1517, 1509, and 1272 inputs/outputs (I/Os) and 1-mm pitch. It presented the thermal cycling (-55C either 100C or 125C) test results for up to 200 cycles. This report presents up to 500 thermal cycles with quality assurance and failure analysis evaluation represented by optical photomicrographs, 2D real time X-ray images, dye-and-pry photomicrographs, and optical/scanning electron Microscopy (SEM) cross-sectional images. The report also presents assembly challenge using reflowing by either vapor phase or rework station of CGA and land grid array (LGA) versions of three high I/O packages both ceramic and plastic configuration. A new test vehicle was designed having high density interconnect (HDI) printed circuit board (PCB) with microvia-in-pad to accommodate both LGA packages as well as a large number of fine pitch ball grid arrays (BGAs). The LGAs either were assembled onto HDI PCB as an LGA or were solder paste print and reflow first to form solder dome on pads before assembly. Both plastic BGAs with 1156 I/O and ceramic LGAs were assembled. It also presented the X-ray inspection results as well as failures due to 200 thermal cycles. Lessons learned on assembly of ceramic LGAs are also presented.

STS-33 MS Carter and MS Thornton display 'Maggot on Board' sign and candy

NASA Technical Reports Server (NTRS)

1989-01-01

STS-33 Mission Specialist (MS) Manley L. Carter, Jr (left) and MS Kathryn C. Thornton display 'Maggot on Board' sign and 'SMARTIES' candy stored in plastic bag on the aft flight deck of Discovery, Orbiter Vehicle (OV) 103. The mission specialists are wearing their mission polo shirts and communications kit assembly headsets. An overhead window appears above their heads. A gold necklace chain floats around Carter's neck.

Method for Designing Electronic Assemblies without Potting for Gun Launched Applications Through the Use of Additive Manufacturing

DTIC Science & Technology

2016-12-01

easily would be preferred. Many studies have been conducted to model the effects of potting materials on PCBs and their components: two such studies ...catch (SCAT) gun Guidance electronics On -board recorder (OBR) Precision guided munition (PGM) 16. SECURITY CLASSIFICATION OF: 17... On -board Recorder 2 Initial Method - Modeling Assumptions 2 Initial Method - Parts, Instances, and Simplifications in the Model 3 Initial Method

OptoZIF Drive: a 3D printed implant and assembly tool package for neural recording and optical stimulation in freely moving mice

NASA Astrophysics Data System (ADS)

Freedman, David S.; Schroeder, Joseph B.; Telian, Gregory I.; Zhang, Zhengyang; Sunil, Smrithi; Ritt, Jason T.

2016-12-01

Objective. Behavioral neuroscience studies in freely moving rodents require small, light-weight implants to facilitate neural recording and stimulation. Our goal was to develop an integrated package of 3D printed parts and assembly aids for labs to rapidly fabricate, with minimal training, an implant that combines individually positionable microelectrodes, an optical fiber, zero insertion force (ZIF-clip) headstage connection, and secondary recording electrodes, e.g. for electromyography (EMG). Approach. Starting from previous implant designs that position recording electrodes using a control screw, we developed an implant where the main drive body, protective shell, and non-metal components of the microdrives are 3D printed in parallel. We compared alternative shapes and orientations of circuit boards for electrode connection to the headstage, in terms of their size, weight, and ease of wire insertion. We iteratively refined assembly methods, and integrated additional assembly aids into the 3D printed casing. Main results. We demonstrate the effectiveness of the OptoZIF Drive by performing real time optogenetic feedback in behaving mice. A novel feature of the OptoZIF Drive is its vertical circuit board, which facilities direct ZIF-clip connection. This feature requires angled insertion of an optical fiber that still can exit the drive from the center of a ring of recording electrodes. We designed an innovative 2-part protective shell that can be installed during the implant surgery to facilitate making additional connections to the circuit board. We use this feature to show that facial EMG in mice can be used as a control signal to lock stimulation to the animal’s motion, with stable EMG signal over several months. To decrease assembly time, reduce assembly errors, and improve repeatability, we fabricate assembly aids including a drive holder, a drill guide, an implant fixture for microelectode ‘pinning’, and a gold plating fixture. Significance. The expanding capability of optogenetic tools motivates continuing development of small optoelectric devices for stimulation and recording in freely moving mice. The OptoZIF Drive is the first to natively support ZIF-clip connection to recording hardware, which further supports a decrease in implant cross-section. The integrated 3D printed package of drive components and assembly tools facilities implant construction. The easy interfacing and installation of auxiliary electrodes makes the OptoZIF Drive especially attractive for real time feedback stimulation experiments.

Full-Scale Experimental Investigation to Quantify Building Component Ignition Vulnerability from Mulch Beds Attacked by Firebrand Showers

PubMed Central

Manzello, Samuel L.; Suzuki, Sayaka; Nii, Daisaku

2015-01-01

Structure ignition by wind-driven firebrand showers is an important fire spread mechanism in large outdoor fires. Experiments were conducted with three common mulch types (shredded hardwood mulch, Japanese Cypress wood chips, and pine bark nuggets) placed adjacent to realistic-scale reentrant corners. In the first series of experiments, mulch beds were placed adjacent to a re-entrant corner constructed with wood studs and lined with oriented strand board (OSB) as the sheathing. The premise behind conducting experiments with no siding treatments applied was predicated on the notion that bare OSB mulch contact would be a worst-case scenario, and therefore, a wall assembly in the most vulnerable state to mulch ignition. In the second series of experiments, vinyl siding was applied to the re-entrant corner assemblies (wood studs/OSB/moisture barrier/vinyl siding), and the influence of vertical separation distance (102 mm or 203 mm) on wall ignition from adjacent mulch beds was determined. The vertical separation distance was maintained by applying gypsum board to the base of the re-entrant corner. The siding itself did not influence the ignition process for the mulch beds, as the mulch beds were the first to ignite from the firebrand showers. In all experiments, it was observed that firebrands produced smoldering ignition in the mulch beds, this transitioned to flaming ignition, and the re-entrant corner assembly was exposed to the flaming mulch beds. With no siding treatments applied, the flaming mulch beds ignited the re-entrant corner, and ignition was observed to propagate to the back side of re-entrant corner assembly under all wind speeds (6 m/s to 8 m/s). With respect to the re-entrant corners fitted with vinyl siding, the mulch type, vertical separation distance, and wind speed were important parameters as to whether flaming ignition was observed to propagate to the back-side of a reentrant corner assembly. Mulches clearly pose an ignition hazard to structures in large outdoor fires. PMID:28184098

Personal Computer (PC) Thermal Analyzer

DTIC Science & Technology

1990-03-01

demonstrate the power of the PC Thermal Analyzer, it was compared with an existing thermal analysis method. Specifically, the PC Thermal Analyzer was...34Intelligence" I T Kowledge 1 User I Inference e Base I Interface 1i FMechanisms H 1 asI I II - I L m m m m m m - m m i m m - m m - m I- m i m Expert...Temperature in degrees centi- grade? (2) What is the total Heat Output ( power dissipation) in watts?). 25 BOARD ASSEMBLY ~UI U2 aooo 0i0000t00 U15

Learning high-quality soldering

NASA Technical Reports Server (NTRS)

Read, W. S.

1981-01-01

Soldering techniques for high-reliability electronic equipment are taught in 5 day course at NASA's Jet Propulsion Laboratory. Topic covered include new circuit assembly, printed-wiring board reworking, circuit changes, wire routing, and component installation.

Ab initio surface properties of Ag-Sn alloys: implications for lead-free soldering.

PubMed

Saleh, Gabriele; Xu, Chen; Sanvito, Stefano

2018-02-07

Ag and Sn are the major components of solder alloys adopted to assemble printed circuit boards. The qualities that make them the alloys of choice for the modern electronic industry are related to their physical and chemical properties. For corrosion resistance and solderability, surface properties are particularly important. Yet, atomic-level information about the surfaces of these alloys is not known. Here we fill this gap by presenting an extensive ab initio investigation of composition, energetics, structure and reactivity of Ag-Sn alloy surfaces. The structure and stability of various surfaces is evaluated, and the main factors determining the energetics of surface formation are uncovered. Oxygen and sulphur chemisorptions are studied and discussed in the framework of corrosion tendency, an important issue for printed circuit boards. Adsorption energy trends are rationalized based on the analysis of structural and electronic features.

Pre-Hospital Care Management of a Potential Spinal Cord Injured Patient: A Systematic Review of the Literature and Evidence-Based Guidelines

PubMed Central

Ahn, Henry; Singh, Jeffrey; Nathens, Avery; MacDonald, Russell D.; Travers, Andrew; Tallon, John; Fehlings, Michael G.

2011-01-01

Abstract An interdisciplinary expert panel of medical and surgical specialists involved in the management of patients with potential spinal cord injuries (SCI) was assembled. Four key questions were created that were of significant interest. These were: (1) what is the optimal type and duration of pre-hospital spinal immobilization in patients with acute SCI?; (2) during airway manipulation in the pre-hospital setting, what is the ideal method of spinal immobilization?; (3) what is the impact of pre-hospital transport time to definitive care on the outcomes of patients with acute spinal cord injury?; and (4) what is the role of pre-hospital care providers in cervical spine clearance and immobilization? A systematic review utilizing multiple databases was performed to determine the current evidence about the specific questions, and each article was independently reviewed and assessed by two reviewers based on inclusion and exclusion criteria. Guidelines were then created related to the questions by a national Canadian expert panel using the Delphi method for reviewing the evidence-based guidelines about each question. Recommendations about the key questions included: the pre-hospital immobilization of patients using a cervical collar, head immobilization, and a spinal board; utilization of padded boards or inflatable bean bag boards to reduce pressure; transfer of patients off of spine boards as soon as feasible, including transfer of patients off spinal boards while awaiting transfer from one hospital institution to another hospital center for definitive care; inclusion of manual in-line cervical spine traction for airway management in patients requiring intubation in the pre-hospital setting; transport of patients with acute traumatic SCI to the definitive hospital center for care within 24 h of injury; and training of emergency medical personnel in the pre-hospital setting to apply criteria to clear patients of cervical spinal injuries, and immobilize patients suspected of having cervical spinal injury. PMID:20175667

Evaluation Transportability Testing of the Joint Modular Intermodal Platform (JMIP) Unit #4 TP-94-01, Revision 2, June 2004, Transportability Testing Procedures

DTIC Science & Technology

2007-07-01

Weight: 19,340 lbs 3-1 5. Semitrailer, flatbed , breakbulk/container transporter, 34 ton Model #: M872A1 Manufactured by Heller Truck Body Corporation...REQD). LAMINATE TO BEARING PIECE W/6-10d NAILS EVENLY SPACED. SIDE STRAPPING BOARD ASSEMBLY (4 RECD) EPAGE 5 NOTE: PRODUCE EQUAL QUANTITES OF ASSEMBLY...A AND ASSEMBLY B. EACH JMIP LOAD REQUIRES iWO OF EACH (4 TOTAL). STEEL EDGE PROTECTORS (2 REQD). LAMINATE TO BEARING AND CORNER PIECES W/4-6d NALS AND

Construction and assembly of the wire planes for the MicroBooNE Time Projection Chamber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Acciarri, R.; Adams, C.; Asaadi, J.

In this paper we describe how the readout planes for the MicroBooNE Time Projection Chamber were constructed, assembled and installed. We present the individual wire preparation using semi-automatic winding machines and the assembly of wire carrier boards. The details of the wire installation on the detector frame and the tensioning of the wires are given. A strict quality assurance plan ensured the integrity of the readout planes. The different tests performed at all stages of construction and installation provided crucial information to achieve the successful realization of the MicroBooNE wire planes.

Development of an anti-flood board to protect the interiors and exteriors of the infrastructure

NASA Astrophysics Data System (ADS)

Petru, Michal; Srb, Pavel; Sevcik, Ladislav; Martinec, Tomas; Kulhavy, Petr

2018-06-01

This article deals with the development of an anti-flood board to protect the interior and exterior of various infrastructures, such a houses, cottages or industrial buildings. It was designed prototypes and assembled numerical simulations. In Central Europe and in particular in the Czech Republic, floods are an integral part of the natural water cycle and cause great loss of life and great property damage. The development of new types of mobile anti-flood boards is very important as the design solution is developed for flood protection with regard to minimizing weight, cost of production, easy manipulation, simplicity and speed of installation.

In-line rotating torque sensor with on-board amplifier

DOEpatents

Kronberg, James W.

1990-01-01

A rotating torque sensor apparatus and method for measuring small torques comprising a shaft, a platform having a circuit board and a first moment arm attached to the shaft, a rotatable wheel coaxial with the shaft and having a second moment arm spaced apart from the first moment arm with a load cell therebetween for generating an electric signal as the torque is applied to the shaft and transferred through the moment arms to the load cell. The electrical signal is conducted from the load cell to the circuit board for filtering and amplification before being extracted from the torque assembly through a slip ring.

Reliability of high I/O high density CCGA interconnect electronic packages under extreme thermal environments

NASA Astrophysics Data System (ADS)

Ramesham, Rajeshuni

2012-03-01

Ceramic column grid array (CCGA) packages have been increasing in use based on their advantages such as high interconnect density, very good thermal and electrical performances, compatibility with standard surfacemount packaging assembly processes, and so on. CCGA packages are used in space applications such as in logic and microprocessor functions, telecommunications, payload electronics, and flight avionics. As these packages tend to have less solder joint strain relief than leaded packages or more strain relief over lead-less chip carrier packages, the reliability of CCGA packages is very important for short-term and long-term deep space missions. We have employed high density CCGA 1152 and 1272 daisy chained electronic packages in this preliminary reliability study. Each package is divided into several daisy-chained sections. The physical dimensions of CCGA1152 package is 35 mm x 35 mm with a 34 x 34 array of columns with a 1 mm pitch. The dimension of the CCGA1272 package is 37.5 mm x 37.5 mm with a 36 x 36 array with a 1 mm pitch. The columns are made up of 80% Pb/20%Sn material. CCGA interconnect electronic package printed wiring polyimide boards have been assembled and inspected using non-destructive x-ray imaging techniques. The assembled CCGA boards were subjected to extreme temperature thermal atmospheric cycling to assess their reliability for future deep space missions. The resistance of daisy-chained interconnect sections were monitored continuously during thermal cycling. This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non-destructive inspection tools were used to assess the reliability of high density CCGA packages for deep space extreme temperature missions.

Elastic-Plastic Nonlinear Response of a Space Shuttle External Tank Stringer. Part 1; Stringer-Feet Imperfections and Assembly

NASA Technical Reports Server (NTRS)

Knight, Norman F., Jr.; Song, Kyongchan; Elliott, Kenny B.; Raju, Ivatury S.; Warren, Jerry E.

2012-01-01

Elastic-plastic, large-deflection nonlinear stress analyses are performed for the external hat-shaped stringers (or stiffeners) on the intertank portion of the Space Shuttle s external tank. These stringers are subjected to assembly strains when the stringers are initially installed on an intertank panel. Four different stringer-feet configurations including the baseline flat-feet, the heels-up, the diving-board, and the toes-up configurations are considered. The assembly procedure is analytically simulated for each of these stringer configurations. The location, size, and amplitude of the strain field associated with the stringer assembly are sensitive to the assumed geometry and assembly procedure. The von Mises stress distributions from these simulations indicate that localized plasticity will develop around the first eight fasteners for each stringer-feet configuration examined. However, only the toes-up configuration resulted in high assembly hoop strains.

Low Density Materials

DTIC Science & Technology

2012-03-09

materials structures across scales for design of engineered systems ODISSEI: Origami Design for Integration of Self-assembling Systems for...AGENCIES Origami Engineering US-India Tunable Materials Forum US-AFRICA Initiative Reliance 21 Board Materials and Processing COI 29 DISTRIBUTION A

50 CFR 622.6 - Vessel and gear identification.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (due east of the NASA Vehicle Assembly Building, Cape Canaveral, FL), or a sea bass pot on board a....archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Copies of the incorporated...

77 FR 46024 - Foreign-Trade Zone 8-Toledo, OH; Notification of Proposed Production Activity, Whirlpool...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-02

..., AC motors, power supplies, heater tubs, LED light assemblies, triple level and push button switches, control panels, printed circuit boards, power cords, wire harnesses, EMI filters, pressure sensors...

BASIC2 INTERPRETER; minimal basic language. [MCS-80,8080-based microcomputers; 8080 Assembly language

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGoldrick, P.R.; Allison, T.G.

The BASIC2 INTERPRETER was developed to provide a high-level easy-to-use language for performing both control and computational functions in the MCS-80. The package is supplied as two alternative implementations, hardware and software. The ''software'' implementation provides the following capabilities: entry and editing of BASIC programs, device-independent I/O, special functions to allow access from BASIC to any I/O port, formatted printing, special INPUT/OUTPUT-and-proceed statements to allow I/O without interrupting BASIC program execution, full arithmetic expressions, limited string manipulation (10 or fewer characters), shorthand forms for common BASIC keywords, immediate mode BASIC statement execution, and capability of running a BASIC program thatmore » is stored in PROM. The allowed arithmetic operations are addition, subtraction, multiplication, division, and raising a number to a positive integral power. In the second, or ''hardware'', implementation of BASIC2 requiring an Am9511 Arithmetic Processing Unit (APU) interfaced to the 8080 microprocessor, arithmetic operations are performed by the APU. The following additional built-in functions are available in this implementation: square root, sine, cosine, tangent, arcsine, arccosine, arctangent, exponential, logarithm base e, and logarithm base 10. MCS-80,8080-based microcomputers; 8080 Assembly language; Approximately 8K bytes of RAM to store the assembled interpreter, additional user program space, and necessary peripheral devices. The hardware implementation requires an Am9511 Arithmetic Processing Unit and an interface board (reference 2).« less

iLIDS Simulations and Videos for Docking TIM

NASA Technical Reports Server (NTRS)

Lewis, James L.

2010-01-01

The video shows various aspects of the International Low Impact Docking System, including team members, some production, configuration, mated androgynous iLIDS, SCS Lockdown system, thermal analysis, electrical engineering aspects, the iLIDS control box and emulator, radiation testing at BNL, component environmental testing, component vibration testing, 3G processor board delivery system, GTA vibe test, EMA testbed, hook and hook disassembly, flex shaftdrive assembly, GSE cradle MISSE-6 Columbus, MISSE 6 and 7 seal experiments, actuated full scale seal test rig, LIDS on Hubble, dynamics test prep, EDU 54 mass emulation and SCS, load ring characterization, 6DOF proof test, SCS at 6DOF, machining EEMS and inner ring assembly, APAS assembly, inner ring fitting, rotation stand assembly, EEMS mating, and EEMS proof of concept demonstration.

Towards co-packaging of photonics and microelectronics in existing manufacturing facilities

NASA Astrophysics Data System (ADS)

Janta-Polczynski, Alexander; Cyr, Elaine; Bougie, Jerome; Drouin, Alain; Langlois, Richard; Childers, Darrell; Takenobu, Shotaro; Taira, Yoichi; Lichoulas, Ted W.; Kamlapurkar, Swetha; Engelmann, Sebastian; Fortier, Paul; Boyer, Nicolas; Barwicz, Tymon

2018-02-01

The impact of integrated photonics on optical interconnects is currently muted by challenges in photonic packaging and in the dense integration of photonic modules with microelectronic components on printed circuit boards. Single mode optics requires tight alignment tolerance for optical coupling and maintaining this alignment in a cost-efficient package can be challenging during thermal excursions arising from downstream microelectronic assembly processes. In addition, the form factor of typical fiber connectors is incompatible with the dense module integration expected on printed circuit boards. We have implemented novel approaches to interfacing photonic chips to standard optical fibers. These leverage standard high throughput microelectronic assembly tooling and self-alignment techniques resulting in photonic packaging that is scalable in manufacturing volume and in the number of optical IOs per chip. In addition, using dense optical fiber connectors with space-efficient latching of fiber patch cables results in compact module size and efficient board integration, bringing the optics closer to the logic chip to alleviate bandwidth bottlenecks. This packaging direction is also well suited for embedding optics in multi-chip modules, including both photonic and microelectronic chips. We discuss the challenges and rewards in this type of configuration such as thermal management and signal integrity.

Prioritizing maintenance human factors challenges and solutions : workshop proceedings.

DOT National Transportation Integrated Search

2011-08-01

Thirty delegates, mostly from the Federal Aviation Administrations Office of Aviation Safety, but also from the : U.S. aviation industry, the National Transportation Safety Board, and Transport Canada, assembled for two : days at the Civil Aerospa...

Prima Platform: A Scheme for Managing Equipment-Dependent Onboard Functions and Impacts on the Avionics Software Production Process

NASA Astrophysics Data System (ADS)

Candia, Sante; Lisio, Giovanni; Campolo, Giovanni; Pascucci, Dario

2010-08-01

The Avionics Software (ASW), in charge of controlling the Low Earth Orbit (LEO) Spacecraft PRIMA Platform (Piattaforma Ri-configurabile Italiana Multi-Applicativa), is evolving towards a highly modular and re-usable architecture based on an architectural framework allowing the effective integration of the software building blocks (SWBBs) providing the on-board control functions. During the recent years, the PRIMA ASW design and production processes have been improved to reach the following objectives: (a) at PUS Services level, separation of the mission-independent software mechanisms from the mission-dependent configuration information; (b) at Application level, identification of mission-independent recurrent functions for promoting abstraction and obtaining a more efficient and safe ASW production, with positive implications also on the software validation activities. This paper is dedicated to the characterisation activity which has been performed at Application level for a software component abstracting a set of functions for the generic On-Board Assembly (OBA), a set of hardware units used to deliver an on-board service. Moreover, the ASW production process is specified to show how it results after the introduction of the new design features.

Stresses in Solder Joints of Electronic Packages

DTIC Science & Technology

1991-12-31

soldering process. The device is soldered to the circuit board at a temperature of +185zc and this tempature is assumed to propagate only to the lead wire...tri-material assembly, showing the notation used hereafter, is shown in Figure 7. The Suhir model is applicable to assemblies with continuous...therefore the radii of curvature of layers are all equal. Using equilibrium equation (7) and moment-curvature equation (9) yields ()D D Xp (x) D T() -m 3 x

Prince George's Community College Annual Cost Containment Report, Submitted to the Maryland Higher Education Commission and the Maryland General Assembly in Compliance with Section 8 of Chapter 465 of the Acts of 1991.

ERIC Educational Resources Information Center

Prince George's Community Coll., Largo, MD. Board of Trustees.

Each year, the Board of Trustees of Prince George's Community College (PGCC), in Maryland, must submit a report evaluating the effectiveness of PGCC's financial plan to the state's Higher Education Committee and General Assembly. This document provides the report for fiscal year (FY) 1996 divided into four sections. The first section reviews the…

Prince George's Community College Annual Cost Containment Report, Submitted to the Maryland Higher Education Commission and the Maryland General Assembly in Compliance with Section 8 of Chapter 465 of the Acts of 1991.

ERIC Educational Resources Information Center

Prince George's Community Coll., Largo, MD. Board of Trustees.

Each year, the Board of Trustees of Prince George's Community College (PGCC) in Largo, Maryland, must submit a report evaluating the effectiveness of PGCC's financial plan to the state's Higher Education Committee and General Assembly. This document provides the report for fiscal year (FY) 1994 divided into four sections. The first section reviews…

Prince George's Community College Annual Cost Containment Report. Submitted to the Maryland Higher Education Commission and the Maryland General Assembly in Compliance with Section 8 of Chapter 465 of the Acts of 1991.

ERIC Educational Resources Information Center

Prince George's Community Coll., Largo, MD. Board of Trustees.

Each year, the Board of Trustees of Prince George's Community College (PGCC) in Largo, Maryland, must submit a report evaluating the effectiveness of PGCC's financial plan to the state's Higher Education Committee and General Assembly. This report, for fiscal year (FY) 1993, is divided into four sections. The first section reviews the cost…

Safety in earth orbit study. Volume 2: Analysis of hazardous payloads, docking, on-board survivability

NASA Technical Reports Server (NTRS)

1972-01-01

Detailed and supporting analyses are presented of the hazardous payloads, docking, and on-board survivability aspects connected with earth orbital operations of the space shuttle program. The hazards resulting from delivery, deployment, and retrieval of hazardous payloads, and from handling and transport of cargo between orbiter, sortie modules, and space station are identified and analyzed. The safety aspects of shuttle orbiter to modular space station docking includes docking for assembly of space station, normal resupply docking, and emergency docking. Personnel traffic patterns, escape routes, and on-board survivability are analyzed for orbiter with crew and passenger, sortie modules, and modular space station, under normal, emergency, and EVA and IVA operations.

Module Configuration

DOEpatents

Oweis, Salah; D'Ussel, Louis; Chagnon, Guy; Zuhowski, Michael; Sack, Tim; Laucournet, Gaullume; Jackson, Edward J.

2002-06-04

A stand alone battery module including: (a) a mechanical configuration; (b) a thermal management configuration; (c) an electrical connection configuration; and (d) an electronics configuration. Such a module is fully interchangeable in a battery pack assembly, mechanically, from the thermal management point of view, and electrically. With the same hardware, the module can accommodate different cell sizes and, therefore, can easily have different capacities. The module structure is designed to accommodate the electronics monitoring, protection, and printed wiring assembly boards (PWAs), as well as to allow airflow through the module. A plurality of modules may easily be connected together to form a battery pack. The parts of the module are designed to facilitate their manufacture and assembly.

Life testing of reflowed and reworked advanced CCGA surface mount packages in harsh thermal environments

NASA Astrophysics Data System (ADS)

Ramesham, Rajeshuni

2013-03-01

Life testing/qualification of reflowed (1st reflow) and reworked (1st reflow, 1st removal, and then 1st rework) advanced ceramic column grid array (CCGA) surface mount interconnect electronic packaging technologies for future flight projects has been studied to enhance the mission assurance of JPL-NASA projects. The reliability of reworked/reflowed surface mount technology (SMT) packages is very important for short-duration and long-duration deep space harsh extreme thermal environmental missions. The life testing of CCGA electronic packages under extreme thermal environments (for example: -185°C to +125°C) has been performed with reference to various JPL/NASA project requirements which encompass the temperature range studied. The test boards of reflowed and reworked CCGA packages (717 Xilinx package, 624, 1152, and 1272 column Actel Packages) were selected for the study to survive three times the total number of expected temperature cycles resulting from all environmental and operational exposures occurring over the life of the flight hardware including all relevant manufacturing, ground operations, and mission phases or cycles to failure to assess the life of the hardware. Qualification/life testing was performed by subjecting test boards to the environmental harsh temperature extremes and assessing any structural failures, mechanical failures or degradation in electrical performance solder-joint failures due to either overstress or thermal cycle fatigue. The large, high density, high input/output (I/O) electronic interconnect SMT packages such as CCGA have increased usage in avionics hardware of NASA projects during the last two decades. The test boards built with CCGA packages are expensive and often require a rework to replace a reflowed, reprogrammed, failed, redesigned, etc., CCGA packages. Theoretically speaking, a good rework process should have similar temperature-time profile as that used for the original manufacturing process of solder reflow. A multiple rework processes may be implemented with CCGA packaging technology to understand the effect of number of reworks on the reliability of this technology for harsh thermal environments. In general, reliability of the assembled electronic packages reduces as a function of number of reworks and the extent is not known yet. A CCGA rework process has been tried and implemented to design a daisy-chain test board consists of 624 and 717 packages. Reworked CCGA interconnect electronic packages of printed wiring polyimide boards have been assembled and inspected using non-destructive x-ray imaging and optical microscope techniques. The assembled boards after 1st rework and 1st reflow were subjected to extreme temperature thermal atmospheric cycling to assess their reliability for future deep space JPL/NASA for moderate to harsh thermal mission environments. The resistance of daisy-chained interconnect sections were monitored continuously during thermal cycling to determine intermittent failures. This paper provides the experimental reliability test results to failure of assemblies for the first time of reflowed and reworked CCGA packages under extreme harsh thermal environments.

VPI - VIBRATION PATTERN IMAGER: A CONTROL AND DATA ACQUISITION SYSTEM FOR SCANNING LASER VIBROMETERS

NASA Technical Reports Server (NTRS)

Rizzi, S. A.

1994-01-01

The Vibration Pattern Imager (VPI) system was designed to control and acquire data from laser vibrometer sensors. The PC computer based system uses a digital signal processing (DSP) board and an analog I/O board to control the sensor and to process the data. The VPI system was originally developed for use with the Ometron VPI Sensor (Ometron Limited, Kelvin House, Worsley Bridge Road, London, SE26 5BX, England), but can be readily adapted to any commercially available sensor which provides an analog output signal and requires analog inputs for control of mirror positioning. VPI's graphical user interface allows the operation of the program to be controlled interactively through keyboard and mouse-selected menu options. The main menu controls all functions for setup, data acquisition, display, file operations, and exiting the program. Two types of data may be acquired with the VPI system: single point or "full field". In the single point mode, time series data is sampled by the A/D converter on the I/O board at a user-defined rate for the selected number of samples. The position of the measuring point, adjusted by mirrors in the sensor, is controlled via a mouse input. In the "full field" mode, the measurement point is moved over a user-selected rectangular area with up to 256 positions in both x and y directions. The time series data is sampled by the A/D converter on the I/O board and converted to a root-mean-square (rms) value by the DSP board. The rms "full field" velocity distribution is then uploaded for display and storage. VPI is written in C language and Texas Instruments' TMS320C30 assembly language for IBM PC series and compatible computers running MS-DOS. The program requires 640K of RAM for execution, and a hard disk with 10Mb or more of disk space is recommended. The program also requires a mouse, a VGA graphics display, a Four Channel analog I/O board (Spectrum Signal Processing, Inc.; Westborough, MA), a break-out box and a Spirit-30 board (Sonitech International, Inc.; Wellesley, MA) which includes a TMS320C30 DSP processor, 256Kb zero wait state SRAM, and a daughter board with 8Mb one wait state DRAM. Please contact COSMIC for additional information on required hardware and software. In order to compile the provided VPI source code, a Microsoft C version 6.0 compiler, a Texas Instruments' TMS320C30 assembly language compiler, and the Spirit 30 run time libraries are required. A math co-processor is highly recommended. A sample MS-DOS executable is provided on the distribution medium. The standard distribution medium for this program is one 5.25 inch 360K MS-DOS format diskette. The contents of the diskettes are compressed using the PKWARE archiving tools. The utility to unarchive the files, PKUNZIP.EXE, is included. VPI was developed in 1991-1992.

Background Equatorial Astronomical Measurements Focal Plane Assembly (Refurbished HI STAR SOUTH)

DTIC Science & Technology

1984-09-01

Subassembly RPT41412 MOSFETs during assembly and test. The old and new designs are shown in Fig- ure 7. The copper webs between the first and second and...machined in the remaining webs be- tween the detector recesses and through a small hole drilled through the frame to connect the traces of all four...gold wirebond routed through a notch machined in the frame web between one of the detector recesses and the board recess. The sap- phire support

Centrifuge-operated specimen staining method and apparatus

NASA Technical Reports Server (NTRS)

Feeback, Daniel L. (Inventor); Clarke, Mark S. F. (Inventor)

1999-01-01

A method of staining preselected, mounted specimens of either biological or nonbiological material enclosed within a staining chamber where the liquid staining reagents are applied and removed from the staining chamber using hypergravity as the propelling force. In the preferred embodiment, a spacecraft-operated centrifuge and method of diagnosing biological specimens while in orbit, characterized by hermetically sealing a shell assembly. The assembly contains slide stain apparatus with computer control therefor, the operative effect of which is to overcome microgravity, for example on board an International Space Station.

Printed Circuit Board Assembly for Use in Space Missions

NASA Technical Reports Server (NTRS)

Petrick, David J. (Inventor); Vo, Luan (Inventor); Albaijes, Dennis (Inventor)

2017-01-01

An electronic assembly for use in space missions that includes a PCB and one or more multi-pin CGA devices coupled to the PCB. The PCB has one or more via-in-pad features and each via-in-pad feature comprises a land pad configured to couple a pin of the one or more multi-pin CGA devices to the via. The PCB also includes a plurality of layers arranged symmetrically in a two-halves configuration above and below a central plane of the PCB.

Whisker Formation Induced by Component and Assembly Ionic Contamination

NASA Astrophysics Data System (ADS)

Snugovsky, Polina; Meschter, Stephan; Bagheri, Zohreh; Kosiba, Eva; Romansky, Marianne; Kennedy, Jeffrey

2012-02-01

This paper describes the results of an intensive whisker formation study on Pb-free assemblies with different levels of cleanliness. Thirteen types of as-received surface-mount and pin-through-hole components were cleaned and intentionally contaminated with solutions containing chloride, sulfate, bromide, and nitrate. Then the parts were assembled on double-sided boards that were also cleaned or intentionally contaminated with three fluxes having different halide contents. The assemblies were subjected to high-temperature/high-humidity testing (85°C/85% RH). Periodic examination found that contamination triggered whisker formation on both exposed tin and solder fillets. Whisker occurrence and parameters depending on the type and level of contamination are discussed. Cross-sections were used to assess the metallurgical aspects of whisker formation and the microstructural changes occurring during corrosion.

Vibration analysis of printed circuit boards: Effect of boundary condition

NASA Astrophysics Data System (ADS)

Prashanth, M. D.

2018-04-01

A spacecraft consists of a number of electronic packages to meet the functional requirements. An electronic package is generally an assembly of printed circuit boards placed in a mechanical housing. A number of electronic components are mounted on the printed circuit board (PCB). A spacecraft experiences various types of loads during its launch such as vibration, acoustic and shock loads. Prediction of response for printed circuit boards due to vibration loads is important for mechanical design and reliability of electronic packages. The modeling and analysis of printed circuit boards is required for accurate prediction of response due to vibration loads. The response of PCB is highly dependent on the mounting configuration of PCB. In addition, anti-vibration mounts or stiffeners are used to reduce the PCB response. Vibration analysis of printed circuit boards is carried out using finite element method. The objective of this paper is to determine the dynamic characteristics of a printed circuit board. Modeling and analysis of PCB shall be carried out to study the effect of boundary conditions on the vibration response. The modeling of stiffeners or ribs shall also be considered in detail. The analysis results shall be validated using vibration tests of PCB.

50 CFR 622.182 - Gear-restricted areas.

Code of Federal Regulations, 2014 CFR

2014-10-01

... scale NOAA chart of the location. A person aboard a vessel with a longline on board that fishes on a... the South Atlantic EEZ south of 28°35.1′ N. lat. (due east of the NASA Vehicle Assembly Building, Cape...

50 CFR 622.182 - Gear-restricted areas.

Code of Federal Regulations, 2013 CFR

2013-10-01

... scale NOAA chart of the location. A person aboard a vessel with a longline on board that fishes on a... the South Atlantic EEZ south of 28°35.1′ N. lat. (due east of the NASA Vehicle Assembly Building, Cape...

Construction and quality assurance of large area resistive strip Micromegas for the upgrade of the ATLAS Muon Spectrometer at LHC/CERN

NASA Astrophysics Data System (ADS)

Lösel, P.

2017-06-01

Large area Micromegas detectors will be employed for the first time in high-energy physics experiments. To cope with increasing background rates, associated with the steadily increasing luminosity of LHC to 10 times design luminosity, the present detector technology in the current innermost stations of the muon endcap system of the ATLAS experiment (the Small Wheel), will be replaced in 2019/2020 by resistive strip Micromegas and small strip TGC detectors. Both technologies will provide tracking and trigger information. In the "New Small Wheel" the Micromegas will be arranged in eight detection layers built of trapezoidally shaped quadruplets of four different sizes covering in total about 1200 m2 of detection plane. In order to achieve 15 % transverse momentum resolution for 1 TeV muons, a challenging mechanical precision is required in the construction of each active plane, with an alignment of the readout strips at the level of 30 μm RMS along the precision coordinate and 80 μm RMS perpendicular to the plane. Each individual Micromegas plane must achieve a spatial resolution better than 100 μm at background rates up to 15 kHz/cm2 while being operated in an inhomogeneous magnetic field (B <= 0.3 T). The required mechanical precision for the production of the components and their assembly, on such large area detectors, is a key point and must be controlled during construction and integration. Particularly the alignment of the readout strips within a quadruplet appears to be demanding. The readout strips are etched on PCB boards using photolithographic processes. Depending on the type of the module, 3 or 5 PCB boards need to be joined and precisely aligned to form a full readout plane. The precision in the alignment is reached either by use of precision mechanical holes or by optical masks, both referenced to the strip patterns. Assembly procedures have been developed to build the single panels with the required mechanical precision and to assemble them in a module including the four metallic micro-meshes. Methods to confirm the precision of components and assembly are based on precise optical devices and X-ray or cosmic muon investigations. We will report on the construction procedures for the Micromegas quadruplets, on the quality control procedures and results, and on the assembly and calibration methods.

BASKET on-board software library

NASA Astrophysics Data System (ADS)

Luntzer, Armin; Ottensamer, Roland; Kerschbaum, Franz

2014-07-01

The University of Vienna is a provider of on-board data processing software with focus on data compression, such as used on board the highly successful Herschel/PACS instrument, as well as in the small BRITE-Constellation fleet of cube-sats. Current contributions are made to CHEOPS, SAFARI and PLATO. The effort was taken to review the various functions developed for Herschel and provide a consolidated software library to facilitate the work for future missions. This library is a shopping basket of algorithms. Its contents are separated into four classes: auxiliary functions (e.g. circular buffers), preprocessing functions (e.g. for calibration), lossless data compression (arithmetic or Rice coding) and lossy reduction steps (ramp fitting etc.). The "BASKET" has all functionality that is needed to create an on-board data processing chain. All sources are written in C, supplemented by optimized versions in assembly, targeting popular CPU architectures for space applications. BASKET is open source and constantly growing

Automated inspection of solder joints for surface mount technology

NASA Technical Reports Server (NTRS)

Savage, Robert M.; Park, Hyun Soo; Fan, Mark S.

1993-01-01

Researchers at NASA/GSFC evaluated various automated inspection systems (AIS) technologies using test boards with known defects in surface mount solder joints. These boards were complex and included almost every type of surface mount device typical of critical assemblies used for space flight applications: X-ray radiography; X-ray laminography; Ultrasonic Imaging; Optical Imaging; Laser Imaging; and Infrared Inspection. Vendors, representative of the different technologies, inspected the test boards with their particular machine. The results of the evaluation showed limitations of AIS. Furthermore, none of the AIS technologies evaluated proved to meet all of the inspection criteria for use in high-reliability applications. It was found that certain inspection systems could supplement but not replace manual inspection for low-volume, high-reliability, surface mount solder joints.

Test of ATLAS RPCs Front-End electronics

NASA Astrophysics Data System (ADS)

Aielli, G.; Camarri, P.; Cardarelli, R.; Di Ciaccio, A.; Di Stante, L.; Liberti, B.; Paoloni, A.; Pastori, E.; Santonico, R.

2003-08-01

The Front-End Electronics performing the ATLAS RPCs readout is a full custom 8 channels GaAs circuit, which integrates in a single die both the analog and digital signal processing. The die is bonded on the Front-End board which is completely closed inside the detector Faraday cage. About 50 000 FE boards are foreseen for the experiment. The complete functionality of the FE boards will be certificated before the detector assembly. We describe here the systematic test devoted to check the dynamic functionality of each single channel and the selection criteria applied. It measures and registers all relevant electronics parameters to build up a complete database for the experiment. The statistical results from more than 1100 channels are presented.

Opto-mechanical design of the MTG FCI spectral separation assembly

NASA Astrophysics Data System (ADS)

Riguet, François; Brousse, Emmanuel; Carel, Jean-Louis; Cottenye, Justine; Harmann, David; Joncour, Marc; Makhlouf, Houssine; Mouricaud, Daniel; Oussalah, Meihdi; Rodolfo, Jacques

2015-09-01

The Spectral Separation Assembly is a key component of the Flexible Combined Imager, an instrument that will be on-board Meteosat Third Generation. It splits the input beam coming from the telescope into five spectral groups, for a total of 16 channels, from 0.4 to 13.3 μm. It comprises a set of four dichroics separators followed by four collimating optics for the infrared spectral groups, which feed the cold imaging optics. The visible spectral group is directly imaged on a detector. This paper presents the optical design of the assembly, the mechanical mounting of the optical components, and the coatings developed for the dichroics, mirrors and lenses.

Marketing Across the Board.

ERIC Educational Resources Information Center

Lauer, Larry D.

1999-01-01

Outlines an eight-step approach to launching an integrated college or university marketing/fund-raising program: finding a visionary campus leader; getting presidential support; assembling a three-tier marketing structure; considering new ways of defining quality; developing a marketing "blueprint"; selling the program on campus; embracing…

Life Cycle Analysis of a SpaceCube Printed Circuit Board Assembly Using Physics of Failure Methodologies

NASA Technical Reports Server (NTRS)

Sood, Bhanu; Evans, John; Daniluk, Kelly; Sturgis, Jason; Davis, Milton; Petrick, David

2017-01-01

In this reliability life cycle evaluation of the SpaceCube 2.0 processor card, a partially populated version of the card is being evaluated to determine its durability with respect to typical GSFC mission loads.

Flexible Packaging by Film-Assisted Molding for Microintegration of Inertia Sensors

PubMed Central

Hera, Daniel; Berndt, Armin; Günther, Thomas; Schmiel, Stephan; Harendt, Christine; Zimmermann, André

2017-01-01

Packaging represents an important part in the microintegration of sensors based on microelectromechanical system (MEMS). Besides miniaturization and integration density, functionality and reliability in combination with flexibility in packaging design at moderate costs and consequently high-mix, low-volume production are the main requirements for future solutions in packaging. This study investigates possibilities employing printed circuit board (PCB-)based assemblies to provide high flexibility for circuit designs together with film-assisted transfer molding (FAM) to package sensors. The feasibility of FAM in combination with PCB and MEMS as a packaging technology for highly sensitive inertia sensors is being demonstrated. The results prove the technology to be a viable method for damage-free packaging of stress- and pressure-sensitive MEMS. PMID:28653992

OWLS as platform technology in OPTOS satellite

NASA Astrophysics Data System (ADS)

Rivas Abalo, J.; Martínez Oter, J.; Arruego Rodríguez, I.; Martín-Ortega Rico, A.; de Mingo Martín, J. R.; Jiménez Martín, J. J.; Martín Vodopivec, B.; Rodríguez Bustabad, S.; Guerrero Padrón, H.

2017-12-01

The aim of this work is to show the Optical Wireless Link to intraSpacecraft Communications (OWLS) technology as a platform technology for space missions, and more specifically its use within the On-Board Communication system of OPTOS satellite. OWLS technology was proposed by Instituto Nacional de Técnica Aeroespacial (INTA) at the end of the 1990s and developed along 10 years through a number of ground demonstrations, technological developments and in-orbit experiments. Its main benefits are: mass reduction, flexibility, and simplification of the Assembly, Integration and Tests phases. The final step was to go from an experimental technology to a platform one. This step was carried out in the OPTOS satellite, which makes use of optical wireless links in a distributed network based on an OLWS implementation of the CAN bus. OPTOS is the first fully wireless satellite. It is based on the triple configuration (3U) of the popular Cubesat standard, and was completely built at INTA. It was conceived to procure a fast development, low cost, and yet reliable platform to the Spanish scientific community, acting as a test bed for space born science and technology. OPTOS presents a distributed OBDH architecture in which all satellite's subsystems and payloads incorporate a small Distributed On-Board Computer (OBC) Terminal (DOT). All DOTs (7 in total) communicate between them by means of the OWLS-CAN that enables full data sharing capabilities. This collaboration allows them to perform all tasks that would normally be carried out by a centralized On-Board Computer.

Mechanical Testing of MLCCs

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander A.

2016-01-01

Cracking of multilayer ceramic capacitors, MLCCs, remains a serious problem for space systems. This problem increases substantially for large size capacitors and in cases when manual soldering is involved or the system experiences mechanical shock or vibration. In any case, a fracture occurs when the sum of external and internal mechanical stresses exceeds the strength of the part. To reduce the probability of cracking, the level of stress should be reduced, e.g. by optimizing the assembly workmanship and rules for board design, and the strength of the parts increased by selecting the most mechanically robust capacitors. The latter might possibly be achieved by selecting MLCCs based on the in-situ measurements of mechanical characteristics using four types of tests: flexural strength, hardness, fracture toughness, and flex bend testing. Note that military specifications MIL-PRF-123 and MIL-PRF-55681 do not have requirements for mechanical testing of the parts. However, specifications for automotive industry components employ two types of mechanical tests: beam load (break strength) test per AEC-Q200-003 and board flex test per AEC-Q200-005. A recent military specification for thin dielectric capacitors, MIL-PRF-32535, has one mechanical test, board flex testing, that is similar to AEC-Q200-005. The purpose of this report was assessment of the efficiency of different mechanical tests for selection robust capacitors and comparison of mechanical characteristics of Base Metal Electrode (BME) and Precious Metal Electrode (PME) capacitors. The report has three parts related to the first three mechanical tests mentioned above.

Single-mode glass waveguide technology for optical interchip communication on board level

NASA Astrophysics Data System (ADS)

Brusberg, Lars; Neitz, Marcel; Schröder, Henning

2012-01-01

The large bandwidth demand in long-distance telecom networks lead to single-mode fiber interconnects as result of low dispersion, low loss and dense wavelength multiplexing possibilities. In contrast, multi-mode interconnects are suitable for much shorter lengths up to 300 meters and are promising for optical links between racks and on board level. Active optical cables based on multi-mode fiber links are at the market and research in multi-mode waveguide integration on board level is still going on. Compared to multi-mode, a single-mode waveguide has much more integration potential because of core diameters of around 20% of a multi-mode waveguide by a much larger bandwidth. But light coupling in single-mode waveguides is much more challenging because of lower coupling tolerances. Together with the silicon photonics technology, a single-mode waveguide technology on board-level will be the straight forward development goal for chip-to-chip optical interconnects integration. Such a hybrid packaging platform providing 3D optical single-mode links bridges the gap between novel photonic integrated circuits and the glass fiber based long-distance telecom networks. Following we introduce our 3D photonic packaging approach based on thin glass substrates with planar integrated optical single-mode waveguides for fiber-to-chip and chip-to-chip interconnects. This novel packaging approach merges micro-system packaging and glass integrated optics. It consists of a thin glass substrate with planar integrated singlemode waveguide circuits, optical mirrors and lenses providing an integration platform for photonic IC assembly and optical fiber interconnect. Thin glass is commercially available in panel and wafer formats and characterizes excellent optical and high-frequency properties. That makes it perfect for microsystem packaging. The paper presents recent results in single-mode waveguide technology on wafer level and waveguide characterization. Furthermore the integration in a hybrid packaging process and design issues are discussed.

7 CFR 984.44 - Duties.

Code of Federal Regulations, 2010 CFR

2010-01-01

... investigate the growing, shipping and marketing conditions with respect to walnuts and to assemble data in... of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... least once for each marketing year and at such other times as the Board deems necessary or as the...

INTERMARS: User-controlled international management system

NASA Technical Reports Server (NTRS)

Schmitt, Harrison H.

1986-01-01

Existing international space law as well as the best interest of all nations are consistent with the establishment of a user-based international organization, herein called INTERMARS. INTERMARS would provide access to facilities and services at a Martian base which would be of high functional potential, quality, safety, and reliability. These opportunities would be available on an open and nondiscriminatory basis to all peaceful users and investors. INTERMARS is a model organization concept tailored to provide cooperative international management of a Martian base for the benefit of its members, users, and investors. Most importantly, INTERMARS would provide such management through a sharing of both sovereignty and opportunity rather then unilateral control by any one nation or set of competing nations. Through an Assembly of Parties, a Board of Governors, a Board of Users and Investors, and a Director General, INTERMARS would meet its primary goal as it would be in the self-interest of all members, users, and investors to do so. The internal structure and philosophy of INTERMARS would provide not only for all participants to have representation in decisions affecting its activities, but also would insure effective and responsive management. Surely this is the precedent wished for, to establish for mankind at the now not-so-distant shores of the new ocean of space.

Solid-State Lighting Module (SSLM)

NASA Technical Reports Server (NTRS)

2008-01-01

The project's goal was to build a light-emitting-diode (LED)-based light fixture that is identical in fit, form, and function to the existing International Space Station (ISS) General Luminaire Assembly (GLA) light fixture and fly it on the ISS in early FY 2008 as a Station Detailed Test Objective (SDTO). Our design offers the following strengths: proven component hardware: Our design uses components flown in other KSC-developed hardware; heat path thermal pad: LED array heat is transferred from the circuit board by silicon pad, negating the need for a cooling fan; variable colorimetry: The output light color can be changed by inserting different LED combinations.

WHO: World Health Assembly.

PubMed

McGregor, A

1992-05-23

1200 delegates from 175 member countries attended the 45th World Health Assembly in Geneva. Everyone at the Assembly ratified measures to prevent and control AIDS. 12 countries intended to do long term planning for community based care for AIDS patients. Further the Assembly denounced instances where countries and individuals denied the gravity of the AIDS pandemic. In fact, it expressed the importance for urgent and intensive action against HIV/AIDS. The assembly backed proposals to prevent and control sexually transmitted diseases that affect AIDS patients, especially hepatitis B. For example, in countries with hepatitis B prevalence 8% (many countries in Sub-Sahara Africa, Asia, the Pacific region, and South America), health officials should introduce hepatitis B vaccine into their existing immunization programs by 1995. By 1997, this vaccine should be part of all immunization programs. The Assembly was aware of the obstacles of establishing reliable cold chains for nationwide distribution, however. Delegates in Committee A objected to the fact that 50% of the populations of developing countries continued to have limited access to essential drugs. They also expressed disapproval in implementation of WHO's 1988 ethical criteria for promotion of drugs which WHO entrusted to the Council for International Organisations of Medical Sciences (CIOMS). CIOMS lacked WHO's status and thus could not effectively monitor drug advertising. In fact, the pharmaceutical industry as well as WHO provided the funds for a meeting of 25 experts to discuss principles included in the ethical criteria. At least 4 countries insisted that WHO have the ultimate authority in monitoring drug advertising. Delegates did adopt a compromise resolution on this topic which required that industry promotion methods be reported to the 1994 Assembly via the Executive Board. The Assembly requested WHO to establish an international advisory committee on nursing and midwifery and to improve the network of WHO collaborating centers which help national nursing groups.

Prototype Aerogel Insulation for Melamine-Foam Substitute: Critical Space Station Express Rack Technology

NASA Technical Reports Server (NTRS)

Noever, David A.; Sibille, Laurent; Smith, David; Cronise, Raymond

1998-01-01

There is a current lack of environmentally acceptable foams to insulate Long-Duration Human Spaceflight Missions, including the experimental Express Rack for the Space Station. A recent 60-day manned test in a sealed chamber at Johnson Space Center (JSC) was nearly aborted, because of persistently high formaldehyde concentrations in the chamber. Subsequent investigation showed that the source was melamine foam (used extensively for acoustic insulation). The thermal and acoustic potential for melamine-foam substitutes is evaluated for scale-up to a silica-based foam and aerogel, which is environmentally benign for long duration space flight. These features will be discussed in reference to an aerogel prototype to: 1) assemble material strength data for various formulated aerogels, both silica and organic carbon aerogels; 2) assemble the aerogel into panels of mylar/vacuum-encapsulated rigid boards which can be molded in various shapes and rigidities; and 3) describe a process for space applications for formaldehyde-free, long duration thermal and acoustic insulators.

A Q-band low noise GaAs pHEMT MMIC power amplifier for pulse electron spin resonance spectrometer

NASA Astrophysics Data System (ADS)

Sitnikov, A.; Kalabukhova, E.; Oliynyk, V.; Kolisnichenko, M.

2017-05-01

We present the design and development of a single stage pulse power amplifier working in the frequency range 32-38 GHz based on a monolithic microwave integrated circuit (MMIC). We have designed the MMIC power amplifier by using the commercially available packaged GaAs pseudomorphic high electron mobility transistor. The circuit fabrication and assembly process includes the elaboration of the matching networks for the MMIC power amplifier and their assembling as well as the topology outline and fabrication of the printed circuit board of the waveguide-microstrip line transitions. At room ambient temperature, the measured peak output power from the prototype amplifier is 35.5 dBm for 16.6 dBm input driving power, corresponding to 19 dB gain. The measured rise/fall time of the output microwave signal modulated by a high-speed PIN diode was obtained as 5-6 ns at 20-250 ns pulse width with 100 kHz pulse repetition rate frequency.

A Q-band low noise GaAs pHEMT MMIC power amplifier for pulse electron spin resonance spectrometer.

PubMed

Sitnikov, A; Kalabukhova, E; Oliynyk, V; Kolisnichenko, M

2017-05-01

We present the design and development of a single stage pulse power amplifier working in the frequency range 32-38 GHz based on a monolithic microwave integrated circuit (MMIC). We have designed the MMIC power amplifier by using the commercially available packaged GaAs pseudomorphic high electron mobility transistor. The circuit fabrication and assembly process includes the elaboration of the matching networks for the MMIC power amplifier and their assembling as well as the topology outline and fabrication of the printed circuit board of the waveguide-microstrip line transitions. At room ambient temperature, the measured peak output power from the prototype amplifier is 35.5 dBm for 16.6 dBm input driving power, corresponding to 19 dB gain. The measured rise/fall time of the output microwave signal modulated by a high-speed PIN diode was obtained as 5-6 ns at 20-250 ns pulse width with 100 kHz pulse repetition rate frequency.

Hi-rel lead-free printed wiring assemblies

NASA Technical Reports Server (NTRS)

Mehta, A. C.; Bonner, J. K.; Castillo, L. del

2002-01-01

The use of lead in electronics has come under increasing scrutiny. Given the trends in both Japan and Europe, it is highly likely that the U.S. will be driven by commercial interests to phase out of lead in electronics usage. This paper presents data collected on a recent NASA project to focus on finding suitable alternatives to eutectic tin-lead solders and solder pastes. The first phase of this project dealt with determining the most feasible candidates to replace tin-lead and to determine suitable processing operations in assemblies printed wiring boards.

Design and construction of a high frame rate imaging system

NASA Astrophysics Data System (ADS)

Wang, Jing; Waugaman, John L.; Liu, Anjun; Lu, Jian-Yu

2002-05-01

A new high frame rate imaging method has been developed recently [Jian-yu Lu, ``2D and 3D high frame rate imaging with limited diffraction beams,'' IEEE Trans. Ultrason. Ferroelectr. Freq. Control 44, 839-856 (1997)]. This method may have a clinical application for imaging of fast moving objects such as human hearts, velocity vector imaging, and low-speckle imaging. To implement the method, an imaging system has been designed. The system consists of one main printed circuit board (PCB) and 16 channel boards (each channel board contains 8 channels), in addition to a set-top box for connections to a personal computer (PC), a front panel board for user control and message display, and a power control and distribution board. The main board contains a field programmable gate array (FPGA) and controls all channels (each channel has also an FPGA). We will report the analog and digital circuit design and simulations, multiplayer PCB designs with commercial software (Protel 99), PCB signal integrity testing and system RFI/EMI shielding, and the assembly and construction of the entire system. [Work supported in part by Grant 5RO1 HL60301 from NIH.

Patterns and Perspectives in Environmental Science.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC. National Science Board.

This report, a supplement to the third annual report of the National Science Board, "Environmental Science, Challenge for the Seventies," contains much of the information and interpretation that formed the basis for the conclusions and recommendations of the annual report. It assembles the views and judgments of leading environmental…

USDOT at 50 : The Early Years Compiled for the 50th anniversary, April 1, 2017

DOT National Transportation Integrated Search

2018-01-17

The essays and recollections appearing here have been assembled in the History Committee of the Transportation Research Board and will be housed in the US DOTs National Transportation Library on the occasion of the 50th anniversary of the opening ...

14 CFR 21.143 - Quality control data requirements; prime manufacturer.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... special manufacturing processes involved, the means used to control the processes, the final test... procedure for recording review board decisions and disposing of rejected parts; (5) An outline of a system...

Improving Robotic Assembly of Planar High Energy Density Targets

NASA Astrophysics Data System (ADS)

Dudt, D.; Carlson, L.; Alexander, N.; Boehm, K.

2016-10-01

Increased quantities of planar assemblies for high energy density targets are needed with higher shot rates being implemented at facilities such as the National Ignition Facility and the Matter in Extreme Conditions station of the Linac Coherent Light Source. To meet this growing demand, robotics are used to reduce assembly time. This project studies how machine vision and force feedback systems can be used to improve the quantity and quality of planar target assemblies. Vision-guided robotics can identify and locate parts, reducing laborious manual loading of parts into precision pallets and associated teaching of locations. On-board automated inspection can measure part pickup offsets to correct part drop-off placement into target assemblies. Force feedback systems can detect pickup locations and apply consistent force to produce more uniform glue bond thickness, thus improving the performance of the targets. System designs and performance evaluations will be presented. Work supported in part by the US DOE under the Science Undergraduate Laboratory Internships Program (SULI) and ICF Target Fabrication DE-NA0001808.

Novel Micro ElectroMechanical Systems (MEMS) Packaging for the Skin of the Satellite

NASA Technical Reports Server (NTRS)

Darrin, M. Ann; Osiander, Robert; Lehtonen, John; Farrar, Dawnielle; Douglas, Donya; Swanson, Ted

2004-01-01

This paper includes a discussion of the novel packaging techniques that are needed to place MEMS based thermal control devices on the skin of various satellites, eliminating the concern associated with potential particulates &om integration and test or the launch environment. Protection of this MEMS based thermal device is achieved using a novel polymer that is both IR transmissive and electrically conductive. This polymer was originally developed and qualified for space flight application by NASA at the Langley Research Center. The polymer material, commercially known as CPI, is coated with a thin layer of ITO and sandwiched between two window-like frames. The packaging of the MEMS based radiator assembly offers the benefits of micro-scale devices in a chip on board fashion, with the level of protection generally found in packaged parts.

Status of the eROSITA Telescope testing and calibrating the x-ray mirror assemblies

NASA Astrophysics Data System (ADS)

Burwitz, Vadim; Predehl, Peter; Bräuninger, Heinrich; Burkert, Wolfgang; Dennerl, Konrad; Eder, Josef; Friedrich, Peter; Fürmetz, Maria; Grisoni, Gabriele; Hartner, Gisela; Marioni, Fabio; Menz, Benedikt; Pfeffermann, Elmar; Valsecchi, Giuseppe

2013-09-01

The eROSITA X-ray observatory that will be launched on board the Russian Spectrum-RG mission comprises seven X-ray telescopes, each with its own mirror assembly (mirror module + X-ray baffle), electron deflector, filter wheel, and CCD camera with its control electronics. The completed flight mirror modules are undergoing many thorough X-ray tests at the PANTHER X-ray test facility after delivery, after being mated with the X-ray baffle, and again after both the vibration and thermal-vacuum tests. A description of the work done with mirror modules/assemblies and the test results obtained will be reported here. We report also on the environmental tests that have been performed on the eROSITA telescope qualification model.

Report of the Seasat Failure Review Board

NASA Technical Reports Server (NTRS)

1993-01-01

The Seasat spacecraft failed on October 9, 1978, after satisfactory operation in orbit for 105 days, as a result of a loss of electrical power in the Agena bus that was used as a part of the spacecraft. The loss of power was caused by a massive and progressive short in one of the slip ring assemblies that was used to connect the rotating solar arrays into the power subsystem. The most likely cause of this short was the initiation of an arc between adjacent slip ring brush assemblies. The triggering mechanism of this arc could have been either a wire-to-brush assembly contact, a brush-to-brush contact, or a momentary short caused by a contaminant that bridged internal components of opposite electrical polarity.

Use of the Ocean for Man’s Wastes. Proceedings of Symposium Held at Lewes, Delaware on 23-24 June 1981.

DTIC Science & Technology

1981-01-01

various physical and biological features of the marine environment in the vicinity of the proposed sludge discharge. At a depth of 300-meters, the slope to...AD-AiII 358 NATIONAL RESEARCH COUNCIL WASHINGTON DC MARINE BOARD F/S 13/2 USE OF THE OCEAN FOR MAN*S WASTES. PROCEEDINGS OF SYMqPOSIUM4 HEL-ETC(U...5 f982 A Marine Board Assembly of Engineering National Research Council This d lt h , bee OPWtO_ e 02 pibhe es1 82 OI 2503 i --:z - ----i

Flight motor set 360L002 (STS-27R). Volume 5: Nozzle component

NASA Technical Reports Server (NTRS)

Meyer, S. A.

1990-01-01

A review of the performance and post-flight condition of the STS-27 Redesigned Solid Rocket Motor (RSRM) nozzles is presented. Thermal/Structural instrumentation data is reviewed, and applicable Discrepancy Reports (DRs) and Process Departures (PDs) are presented. The Nozzle Component Program Team (NCPT) performance evaluation and the Redesign Program Review Board (RPRB) assessment is included. The STS-27 nozzle assemblies were flown on the RSRM Second Flight (Space Shuttle Atlantis) on 2 December 1988. The nozzles were a partially submerged convergent and/or divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: RSRM forward exit cone with snubber assembly, RSRM fixed housing, Structural backup Outer Boot Ring (OBR), RSRM cowl ring, RSRM nose inlet assembly, RSRM throat assembly, RSRM aft exit cone assembly with Linear-Shaped Charge (LSC), RTV backfill in Joints 1, 3, and 4, Use of EA913 NA adhesive in place of EA913 adhesive, Redesigned nozzle plug, and Carbon Cloth Phenolic (CCP) with 750 ppm sodium content. The CCP material usage for the STS-27 forward nozzle and aft exit cone assemblies is shown.

Ship Dynamics in the Surf Zone Model Testing

DTIC Science & Technology

2008-07-01

was implemented for ease of transportation and ease of assembly. Each module was 10 feet square consisting of oriented strand board ( OSB ) plywood with...frame, constructed of 2 inch by 4 inch by 10 feet pieces of wood, was measured, cut, laid, and screwed together for each module. Pieces of OSB

78 FR 66330 - Foreign-Trade Zone 196-Fort Worth, Texas, Authorization of Production Activity, Flextronics...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-05

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-62-2013] Foreign-Trade Zone 196--Fort Worth, Texas, Authorization of Production Activity, Flextronics International USA, Inc. (Mobile Phone Assembly and Kitting), Fort Worth, Texas On June 14, 2013, Flextronics International USA, Inc. submitted a...

78 FR 11816 - Foreign-Trade Zone 168-Dallas/Ft. Worth, TX, Authorization of Production Activity, Richemont...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-20

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-76-2012] Foreign-Trade Zone 168--Dallas/Ft. Worth, TX, Authorization of Production Activity, Richemont North America, Inc. dba Cartier (Eyewear Assembly/Kitting), Grand Prairie, TX On October 17, 2012, Metroplex International Trade Development...

78 FR 60826 - Foreign-Trade Zone 155-Calhoun/Victoria Counties, Texas; Authorization of Production Activity...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-02

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board Foreign-Trade Zone 155--Calhoun/Victoria Counties, Texas; Authorization of Production Activity; Caterpillar, Inc. (Excavator and Frame Assembly Production); Victoria, Texas On May 29, 2013, The Calhoun-Victoria Foreign Trade Zone, Inc., grantee of FTZ 155...

High-Frequency Learning.

ERIC Educational Resources Information Center

Hollenbeck, Michelle D.

1997-01-01

For the past five years, Andover, Kansas middle-schoolers in an amateur radio club and class have sent and received Morse code messages, assembled and soldered circuit boards, designed and built antenna systems, and used computer programs to analyze radio communications problems. A successful bond issue financed a ham shack enabling students to…

Portable Breathing Assembly

NASA Image and Video Library

2017-06-12

In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, Jacobs Test and Operations Support Contract, or TOSC, technicians fill portable breathing apparatuses, or PBAS. The PBAs are to be use on board the International Space Staton to provide astronauts with breathable air in the event of a fire or other emergency situation.

Essentials of Nutrition Education in Medical Schools: A National Consensus.

ERIC Educational Resources Information Center

Academic Medicine, 1996

1996-01-01

The American Medical Student Association's Nutrition Curriculum Project assembled a 10-member advisory board to develop a comprehensive list of nutrition topics deemed essential for the adequate training of physicians. The resulting 92 topics are divided into 5 major categories: (1) biochemistry/physiology/pathophysiology; (2) nutrition…

Critical Issues Facing America's Community Colleges: A Summary of the Community College Futures Assembly 2008

ERIC Educational Resources Information Center

Basham, Matthew J.; Campbell, Dale F.; Mendoza, Pilar

2008-01-01

Three focus groups consisting of board of trustee members, community college presidents, senior administrators, administrators, and faculty members developed critical issues facing community colleges with respect to instructional planning and services; planning, governance, and finance; and workforce development. Thereafter, the delegation of more…

Promote Your Vocational Office Education Program

ERIC Educational Resources Information Center

Boyd, Daniel R.

1973-01-01

Suggestions for promoting a VOE program within the school include these: bulletin boards and displays, school publications, assemblies, and VOE club activites. Community promotional activities include use of store windows for displays, use of mass media, recognition of local businessmen at the VOE banquet, and programs presented to service clubs.…

The IBM PC as an Online Search Machine--Part 2: Physiology for Searchers.

ERIC Educational Resources Information Center

Kolner, Stuart J.

1985-01-01

Enumerates "hardware problems" associated with use of the IBM personal computer as an online search machine: purchase of machinery, unpacking of parts, and assembly into a properly functioning computer. Components that allow transformations of computer into a search machine (combination boards, printer, modem) and diagnostics software…

Automated visual inspection system based on HAVNET architecture

NASA Astrophysics Data System (ADS)

Burkett, K.; Ozbayoglu, Murat A.; Dagli, Cihan H.

1994-10-01

In this study, the HAusdorff-Voronoi NETwork (HAVNET) developed at the UMR Smart Engineering Systems Lab is tested in the recognition of mounted circuit components commonly used in printed circuit board assembly systems. The automated visual inspection system used consists of a CCD camera, a neural network based image processing software and a data acquisition card connected to a PC. The experiments are run in the Smart Engineering Systems Lab in the Engineering Management Dept. of the University of Missouri-Rolla. The performance analysis shows that the vision system is capable of recognizing different components under uncontrolled lighting conditions without being effected by rotation or scale differences. The results obtained are promising and the system can be used in real manufacturing environments. Currently the system is being customized for a specific manufacturing application.

Case study of rotating sonar sensor application in unmanned automated guided vehicle

NASA Astrophysics Data System (ADS)

Chandak, Pravin; Cao, Ming; Hall, Ernest L.

2001-10-01

A single rotating sonar element is used with a restricted angle of sweep to obtain readings to develop a range map for the unobstructed path of an autonomous guided vehicle (AGV). A Polaroid ultrasound transducer element is mounted on a micromotor with an encoder feedback. The motion of this motor is controlled using a Galil DMC 1000 motion control board. The encoder is interfaced with the DMC 1000 board using an intermediate IMC 1100 break-out board. By adjusting the parameters of the Polaroid element, it is possible to obtain range readings at known angles with respect to the center of the robot. The readings are mapped to obtain a range map of the unobstructed path in front of the robot. The idea can be extended to a 360 degree mapping by changing the assembly level programming on the Galil Motion control board. Such a system would be compact and reliable over a range of environments and AGV applications.

Technological development of multispectral filter assemblies for micro bolometer

NASA Astrophysics Data System (ADS)

Le Goff, Roland; Tanguy, François; Fuss, Philippe; Etcheto, Pierre

2017-11-01

Since 2007 Sodern has successfully developed visible and near infrared multispectral filter assemblies for Earth remote sensing imagers. Filter assembly is manufactured by assembling several sliced filter elements (so-called strips), each corresponding to one spectral band. These strips are cut from wafers using a two dimensional accuracy precision process. In the frame of a 2011 R&T preparatory initiative undertaken by the French agency CNES, the filter assembly concept was adapted by Sodern to the long wave infrared spectral band taken into account the germanium substrate, the multilayer bandpass filters and the F-number of the optics. Indeed the current trend in space instrumentation toward more compact uncooled infrared radiometer leads to replace the filter wheel with a multispectral filter assembly mounted directly above the micro bolometer window. The filter assembly was customized to fit the bolometer size. For this development activity we consider a ULIS VGA LWIR micro bolometer with 640 by 480 pixels and 25 microns pixel pitch. The feasibility of the concept and the ability to withstand space environment were investigated and demonstrated by bread boarding activities. The presentation will contain a detailed description of the bolometer and filter assembly design, the stray light modeling analysis assessing the crosstalk between adjacent spectral bands and the results of the manufacturing and environmental tests (damp heat and thermal vacuum cycling).

Development of a large area microstructure photomultiplier assembly (LAMPA)

NASA Astrophysics Data System (ADS)

Clifford, E. T. H.; Dick, M.; Facina, M.; Wakeford, D.; Andrews, H. R.; Ing, H.; Best, D.; Baginski, M. J.

2017-05-01

Large area (> m2) position-sensitive readout of scintillators is important for passive/active gamma and neutron imaging for counter-terrorism applications. The goal of the LAMPA project is to provide a novel, affordable, large-area photodetector (8" x 8") by replacing the conventional dynodes of photomultiplier tubes (PMTs) with electron multiplier microstructure boards (MSBs) that can be produced using industrial manufacturing techniques. The square, planar format of the LAMPA assemblies enables tiling of multiple units to support large area applications. The LAMPA performance objectives include comparable gain, noise, timing, and energy resolution relative to conventional PMTs, as well as spatial resolution in the few mm range. The current LAMPA prototype is a stack of 8" x 8" MSBs made commercially by chemical etching of a molybdenum substrate and coated with hydrogen-terminated boron-doped diamond for high secondary emission yield (SEY). The layers of MSBs are electrically isolated using ceramic standoffs. Field-shaping grids are located between adjacent boards to achieve good transmission of electrons from one board to the next. The spacing between layers and the design of the microstructure pattern and grids were guided by simulations performed using an electro-optics code. A position sensitive anode board at the back of the stack of MSBs provides 2-D readout. This presentation discusses the trade studies performed in the design of the MSBs, the measurements of SEY from various electro-emissive materials, the electro-optics simulations conducted, the design of the 2-D readout, and the mechanical aspects of the LAMPA design, in order to achieve a gain of > 104 in an 8-stage stack of MSBs, suitable for use with various scintillators when coupled to an appropriate photocathode.

Design principles and realization of electro-optical circuit boards

NASA Astrophysics Data System (ADS)

Betschon, Felix; Lamprecht, Tobias; Halter, Markus; Beyer, Stefan; Peterson, Harry

2013-02-01

The manufacturing of electro-optical circuit boards (EOCB) is based to a large extent on established technologies. First products with embedded polymer waveguides are currently produced in series. The range of applications within the sensor and data communication markets is growing with the increasing maturity level. EOCBs require design flows, processes and techniques similar to existing printed circuit board (PCB) manufacturing and appropriate for optical signal transmission. A key aspect is the precise and automated assembly of active and passive optical components to the optical waveguides which has to be supported by the technology. The design flow is described after a short introduction into the build-up of EOCBs and the motivation for the usage of this technology within the different application fields. Basis for the design of EOCBs are the required optical signal transmission properties. Thereafter, the devices for the electro-optical conversion are chosen and the optical coupling approach is defined. Then, the planar optical elements (waveguides, splitters, couplers) are designed and simulated. This phase already requires co-design of the optical and electrical domain using novel design flows. The actual integration of an optical system into a PCB is shown in the last part. The optical layer is thereby laminated to the purely electrical PCB using a conventional PCB-lamination process to form the EOCB. The precise alignment of the various electrical and optical layers is thereby essential. Electrical vias are then generated, penetrating also the optical layer, to connect the individual electrical layers. Finally, the board has to be tested electrically and optically.

WDM package enabling high-bandwidth optical intrasystem interconnects for high-performance computer systems

NASA Astrophysics Data System (ADS)

Schrage, J.; Soenmez, Y.; Happel, T.; Gubler, U.; Lukowicz, P.; Mrozynski, G.

2006-02-01

From long haul, metro access and intersystem links the trend goes to applying optical interconnection technology at increasingly shorter distances. Intrasystem interconnects such as data busses between microprocessors and memory blocks are still based on copper interconnects today. This causes a bottleneck in computer systems since the achievable bandwidth of electrical interconnects is limited through the underlying physical properties. Approaches to solve this problem by embedding optical multimode polymer waveguides into the board (electro-optical circuit board technology, EOCB) have been reported earlier. The principle feasibility of optical interconnection technology in chip-to-chip applications has been validated in a number of projects. For reasons of cost considerations waveguides with large cross sections are used in order to relax alignment requirements and to allow automatic placement and assembly without any active alignment of components necessary. On the other hand the bandwidth of these highly multimodal waveguides is restricted due to mode dispersion. The advance of WDM technology towards intrasystem applications will provide sufficiently high bandwidth which is required for future high-performance computer systems: Assuming that, for example, 8 wavelength-channels with 12Gbps (SDR1) each are given, then optical on-board interconnects with data rates a magnitude higher than the data rates of electrical interconnects for distances typically found at today's computer boards and backplanes can be realized. The data rate will be twice as much, if DDR2 technology is considered towards the optical signals as well. In this paper we discuss an approach for a hybrid integrated optoelectronic WDM package which might enable the application of WDM technology to EOCB.

Designing learning apparatus to promote twelfth grade students’ understanding of digital technology concept: A preliminary studies

NASA Astrophysics Data System (ADS)

Marlius; Kaniawati, I.; Feranie, S.

2018-05-01

A preliminary learning design using relay to promote twelfth grade student’s understanding of logic gates concept is implemented to see how well it’s to adopted by six high school students, three male students and three female students of twelfth grade. This learning design is considered for next learning of digital technology concept i.e. data digital transmition and analog. This work is a preliminary study to design the learning for large class. So far just a few researches designing learning design related to digital technology with relay. It may due to this concept inserted in Indonesian twelfth grade curriculum recently. This analysis is focus on student difficulties trough video analysis to learn the concept. Based on our analysis, the recommended thing for redesigning learning is: students understand first about symbols and electrical circuits; the Student Worksheet is made in more detail on the assembly steps to the project board; mark with symbols at points in certain places in the circuit for easy assembly; assembly using relays by students is enough until is the NOT’s logic gates and the others that have been assembled so that effective time. The design of learning using relays can make the relay a liaison between the abstract on the digital with the real thing of it, especially in the circuit of symbols and real circuits. Besides it is expected to also enrich the ability of teachers in classroom learning about digital technology.

PCBA depaneling stress minimization study

NASA Astrophysics Data System (ADS)

Darus, M. H. B. M.; Aziz, M. H. B. A.; Ong, N. R.; Alcain, J. B.; Retnasamy, V.

2017-09-01

Printed circuit board (PCB) is board that used to connect the electricity using the conductive pathways. The PCB that consists with electronic components was called as printed circuit board assembly (PCBA). Bending process has been used as one of the depaneling techniques may contribute to mechanical stress and the failure of capacitors and other components to function. As a result, the idea to create holes in particular location was implemented in order to absorb the stress. In this study, finite element analysis is demonstrated by using ANSYS software. Two PCBA design models are considered in order to investigate the effect of the hole and the stress response. The simulation results show that the hole on the PCBA has reduced the stress. For Design model 2, the stress response of the holes located vertically to the PCBA is lower than the holes located horizontally to the PCBA.

Long life assurance study for manned spacecraft long life hardware. Volume 4: Special long life assurance studies

NASA Technical Reports Server (NTRS)

1972-01-01

Guidelines for the selection of equipment to be used for manned spacecraft in order to assure a five year maintenance-free service life were developed. A special study was conducted to determine the adequacy of the procedures used to determine the quality and effectiveness of various components. The subjects examined are: (1) temperature cycling for acceptance of electronic assemblies; (2) accelerated testing techniques; (3) electronic part screening techniques; (4) electronic part derating practices; (5) vibration life extension of printed circuit board assemblies; and (6) tolerance funnelling and test requirements.

2011 Report Card on the Effectiveness of Teacher Training Programs

ERIC Educational Resources Information Center

Tennessee State Board of Education, 2011

2011-01-01

The Tennessee General Assembly passed legislation in 2007 requiring that the State Board of Education produce an assessment on the effectiveness of teacher training programs. The law requires that the report includes data on the performance of each program's graduates in the following areas: placement and retention rates, Praxis II results, and…

77 FR 24177 - Approval for Manufacturing Authority; Foreign-Trade Zone 177; Hoosier Stamping & Mfg. Corp...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-23

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [Order No. 1822] Approval for Manufacturing Authority; Foreign-Trade Zone 177; Hoosier Stamping & Mfg. Corp. (Wheel Assemblies and Accessories); Chandler, IN Pursuant to its authority under the Foreign-Trade Zones Act of June 18, 1934, as amended (19 U...

In the Boardroom, Culture Counts

ERIC Educational Resources Information Center

Axelrod, Nancy R.

2005-01-01

Many higher education leaders are adopting measures that may contribute to better governance, but unless they also look at how the phenomenon of culture shapes the way their board members behave as a group, they will miss the forest for the trees. The best trustees and presidents grasp the paradox of assembling a number of highly competent…

Critical Issues Facing America's Community Colleges: A Summary of the Community Colleges Futures Assembly 2006

ERIC Educational Resources Information Center

Campbell, Dale F.; Basham, Matthew J.

2007-01-01

Three focus groups consisting of 42 board of trustee members, community college presidents, senior administrators, and faculty members developed critical issues facing community colleges with respect to instructional planning and services; planning, governance, finance; and workforce development. Thereafter, the delegation of more than 200 voted…

Low cost airborne microwave landing system receiver, task 3

NASA Technical Reports Server (NTRS)

Hager, J. B.; Vancleave, J. R.

1979-01-01

Work performed on the low cost airborne Microwave Landing System (MLS) receiver is summarized. A detailed description of the prototype low cost MLS receiver is presented. This detail includes block diagrams, schematics, board assembly drawings, photographs of subassemblies, mechanical construction, parts lists, and microprocessor software. Test procedures are described and results are presented.

Collaborative Governance: Structures for Success. The California and Yosemite Community College District Experience.

ERIC Educational Resources Information Center

Draper, Brice; Van Groningen, Tom

Assembly Bill (AB) 1725 addresses the mission, functions, governance, finance, staffing, programs, services, and accountability of the California Community Colleges (CCC). Many of the bill's recommendations place emphasis on the 107 community colleges, the CCC Chancellor's Office, and the Board of Governors (BOG) becoming a single system of…

Logistics for the implementation of lead-free solders on electronic assemblies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vianco, P.T.; Artaki, I.

1993-12-31

The prospects of legislative and regulatory action aimed at taxing, restricting or banning lead-bearing materials from manufactured products has prompted the electronics community to examine the implementation of lead-free solders to replace currently used lead-containing alloys in the manufacture of electronic devices and assemblies. The logistics for changing the well established ``tin-lead solder technology`` require not only the selection of new compositions but also the qualification of different surface finishes and manufacturing processes. The meniscometer/wetting balance technique was used to evaluate the wettability of several candidate lead-free solders as well as to establish windows on processing parameters so as tomore » facilitate prototype manufacturing. Electroplated and electroless 100Sn coatings, as well as organic preservatives, were also examined as potential alternative finishes for device leads and terminations as well as circuit board conductor surfaces to replace traditional tin-lead layers. Sandia National Laboratories and AT&T have implemented a program to qualify the manufacturing feasibility of surface mount prototype circuit boards using several commercial lead-free solders by infrared reflow technology.« less

Battery Control Boards for Li-Ion Batteries on Mars Exploration Rovers

NASA Technical Reports Server (NTRS)

Ewell, R.; Ratnakumar, B. V.; Smart, M.; Chin, K. B.; Whitcanack, L.; Narayanan, S. R.; Surampudi, S.

2006-01-01

Rechargeable Lithium-ion batteries have been operating successfully on both Spirit and Opportunity rovers for the last two years, which includes six months of Assembly Launch and Test Operations (ATLO), seven months of cruise and about eleven months of surface operations. The Battery Control Boards designed and fabricated in-house would protect cells against overcharge and over-discharge and provide cell balance. Their performance has thus far been quite satisfactory. The ground data o the mission simulation battery project little capacity loss of less than 3% during cruise and 180 sols. Batteries are poised to extend the mission beyond six months, if not a couple of years.

An Autonomous Underwater Recorder Based on a Single Board Computer.

PubMed

Caldas-Morgan, Manuel; Alvarez-Rosario, Alexander; Rodrigues Padovese, Linilson

2015-01-01

As industrial activities continue to grow on the Brazilian coast, underwater sound measurements are becoming of great scientific importance as they are essential to evaluate the impact of these activities on local ecosystems. In this context, the use of commercial underwater recorders is not always the most feasible alternative, due to their high cost and lack of flexibility. Design and construction of more affordable alternatives from scratch can become complex because it requires profound knowledge in areas such as electronics and low-level programming. With the aim of providing a solution; a well succeeded model of a highly flexible, low-cost alternative to commercial recorders was built based on a Raspberry Pi single board computer. A properly working prototype was assembled and it demonstrated adequate performance levels in all tested situations. The prototype was equipped with a power management module which was thoroughly evaluated. It is estimated that it will allow for great battery savings on long-term scheduled recordings. The underwater recording device was successfully deployed at selected locations along the Brazilian coast, where it adequately recorded animal and manmade acoustic events, among others. Although power consumption may not be as efficient as that of commercial and/or micro-processed solutions, the advantage offered by the proposed device is its high customizability, lower development time and inherently, its cost.

Straight talk with...Jonathan Quick. Interview by Roxanne Khamsi.

PubMed

Quick, Jonathan

2013-09-01

In April 2012, an e-mail announcing the impending closure of the Global Health Council following the cancellation of its annual conference sent shockwaves through its community of 325 organizational members spanning 39 countries. For 40 years, the Alexandria, Virginia-based nonprofit had acted as an umbrella organization for stakeholders that include some of the world's most prominent medical institutions and drug companies. As the June 2012 closure of the GHC approached, several members stepped in to rescue the operation, including Jonathan Quick, a family physician and CEO of Management Sciences for Health, a Cambridge, Massachusetts-based outfit that works to strengthen health systems and infrastructure around the globe. In January, a new GHC board was elected, with Quick at the helm. In the ensuing months the board members have built the organization back up-albeit as a leaner and more targeted operation. This past summer, they launched a revamped website (www.globalhealth.org) and are looking ahead to convening GHC members at the UN General Assembly on 18 September in New York, where the discussion of Millennium Development Goals will take place. As Nature Medicine went to press, the relaunched GHC was in the midst of recruiting for its first staff position, executive director. Roxanne Khamsi spoke with Quick about the health of the organization.

Studying Spatial Resolution of CZT Detectors Using Sub-Pixel Positioning for SPECT

NASA Astrophysics Data System (ADS)

Montémont, Guillaume; Lux, Silvère; Monnet, Olivier; Stanchina, Sylvain; Verger, Loïck

2014-10-01

CZT detectors are the basic building block of a variety of new SPECT systems. Their modularity allows adapting system architecture to specific applications such as cardiac, breast, brain or small animal imaging. In semiconductors, a high number of electron-hole pairs is produced by a single interaction. This direct conversion process allows better energy and spatial resolutions than usual scintillation detectors based on NaI(Tl). However, it remains often unclear if SPECT imaging can really benefit of that performance gain. We investigate the system performance of a detection module, which is based on 5 mm thick CZT with a segmented anode having a 2.5 mm pitch by simulation and experimentation. This pitch allows an easy assembly of the crystal on the readout board and limits the space occupied by electronics without significantly degrading energy and spatial resolution.

Design and construction of smart cane using infrared laser-based tracking system

NASA Astrophysics Data System (ADS)

Wong, Chi Fung; Phitagragsakul, Narikorn; Jornsamer, Patcharaporn; Kaewmeesri, Pimsin; Jantakot, Pimsunan; Locharoenrat, Kitsakorn

2018-06-01

Our work is aimed to design and construct the smart cane. The infrared laser-based sensor was used as a distance detector and Arduino board was used as a microcontroller. On the other hand, Bluetooth was used as a wireless communicator and MP3 module together with the headset were used as a voice alert player. Our smart cane is a very effective device for the users under the indoor guidance. That is, the obstacle was detectable 3,000 cm away from the blind people. The white cane was assembled with the laser distance sensor and distance alert sensor served as the compact and light-weight device. Distance detection was very fast and precise when the smart cane was tested for the different obstacles, such as human, wall and wooden table under the indoor area.

Piezoelectric-based self-powered electronic adjustable impulse switches

NASA Astrophysics Data System (ADS)

Rastegar, Jahangir; Kwok, Philip

2018-03-01

Novel piezoelectric-based self-powered impulse detecting switches are presented. The switches are designed to detect shock loading events resulting in acceleration or deceleration above prescribed levels and durations. The prescribed acceleration level and duration thresholds are adjustable. They are provided with false trigger protection logic. The impulse switches are provided with electronic and logic circuitry to detect prescribed impulse events and reject events such as high amplitude but short duration shocks, and transportation vibration and similar low amplitude and relatively long duration events. They can be mounted directly onto electronics circuit boards, thereby significantly simplifying the electrical and electronic circuitry, simplifying the assembly process and total cost, significantly reducing the occupied volume, and in some applications eliminating the need for physical wiring to and from the impulse switches. The design of prototypes and testing under realistic conditions are presented.

Fabrication of Fresnel micro lens array in borosilicate glass by F2-laser ablation for glass interposer application

NASA Astrophysics Data System (ADS)

Brusberg, Lars; Neitz, Marcel; Schröder, Henning; Fricke-Begemann, Thomas; Ihlemann, Jürgen

2014-03-01

The future need for more bandwidth forces the development of optical transmission solutions for rack-to-rack, boardto- board and chip-to-chip interconnects. The goals are significant reduction of power consumption, highest density and potential for bandwidth scalability to overcome the limitations of the systems today with mostly copper based interconnects. For system integration the enabling of thin glass as a substrate material for electro-optical components with integrated micro-optics for efficient light coupling to integrated optical waveguides or fibers is becoming important. Our glass based packaging approach merges micro-system packaging and glass integrated optics. This kind of packaging consists of a thin glass substrate with integrated micro lenses providing a platform for photonic component assembly and optical fiber or waveguide interconnection. Thin glass is commercially available in panel and wafer size and characterizes excellent optical and high frequency properties. That makes it perfect for microsystem packaging. A suitable micro lens approach has to be comparable with different commercial glasses and withstand post-processing like soldering. A benefit of using laser ablated Fresnel lenses is the planar integration capability in the substrate for highest integration density. In the paper we introduce our glass based packaging concept and the Fresnel lens design for different scenarios like chip-to-fiber, chip-to-optical-printed-circuit-board coupling. Based on the design the Fresnel lenses were fabricated by using a 157 nm fluorine laser ablation system.

Energy Input Flux in the Global Quiet-Sun Corona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mac Cormack, Cecilia; Vásquez, Alberto M.; López Fuentes, Marcelo

We present first results of a novel technique that provides, for the first time, constraints on the energy input flux at the coronal base ( r ∼ 1.025 R {sub ⊙}) of the quiet Sun at a global scale. By combining differential emission measure tomography of EUV images, with global models of the coronal magnetic field, we estimate the energy input flux at the coronal base that is required to maintain thermodynamically stable structures. The technique is described in detail and first applied to data provided by the Extreme Ultraviolet Imager instrument, on board the Solar TErrestrial RElations Observatory mission,more » and the Atmospheric Imaging Assembly instrument, on board the Solar Dynamics Observatory mission, for two solar rotations with different levels of activity. Our analysis indicates that the typical energy input flux at the coronal base of magnetic loops in the quiet Sun is in the range ∼0.5–2.0 × 10{sup 5} (erg s{sup −1} cm{sup −2}), depending on the structure size and level of activity. A large fraction of this energy input, or even its totality, could be accounted for by Alfvén waves, as shown by recent independent observational estimates derived from determinations of the non-thermal broadening of spectral lines in the coronal base of quiet-Sun regions. This new tomography product will be useful for the validation of coronal heating models in magnetohydrodinamic simulations of the global corona.« less

Mosad and Stream Vision For A Telerobotic, Flying Camera System

NASA Technical Reports Server (NTRS)

Mandl, William

2002-01-01

Two full custom camera systems using the Multiplexed OverSample Analog to Digital (MOSAD) conversion technology for visible light sensing were built and demonstrated. They include a photo gate sensor and a photo diode sensor. The system includes the camera assembly, driver interface assembly, a frame stabler board with integrated decimeter and Windows 2000 compatible software for real time image display. An array size of 320X240 with 16 micron pixel pitch was developed for compatibility with 0.3 inch CCTV optics. With 1.2 micron technology, a 73% fill factor was achieved. Noise measurements indicated 9 to 11 bits operating with 13.7 bits best case. Power measured under 10 milliwatts at 400 samples per second. Nonuniformity variation was below noise floor. Pictures were taken with different cameras during the characterization study to demonstrate the operable range. The successful conclusion of this program demonstrates the utility of the MOSAD for NASA missions, providing superior performance over CMOS and lower cost and power consumption over CCD. The MOSAD approach also provides a path to radiation hardening for space based applications.

Novel Ultrahigh Vacuum System for Chip-Scale Trapped Ion Quantum Computing

NASA Astrophysics Data System (ADS)

Chen, Shaw-Pin; Trapped Team

2011-05-01

This presentation reports the experimental results of an ultrahigh vacuum (UHV) system as a scheme to implement scalable trapped-ion quantum computers that use micro-fabricated ion traps as fundamental building blocks. The novelty of this system resides in our design, material selection, mechanical liability, low complexity of assembly, and reduced signal interference between DC and RF electrodes. Our system utilizes RF isolation and onsite-filtering topologies to attenuate AC signals generated from the resonator. We use a UHV compatible printed circuit board (PCB) material to perform DC routing, while the RF high and RF ground received separated routing via wire-wrapping. The standard PCB fabrication process enabled us to implement ceramic-based filter components adjacent to the chip trap. The DC electrodes are connected to air-side electrical feed through using four 25D adaptors made with polyether ether ketone (PEEK). The assembly process of this system is straight forward and in-chamber structure is self-supporting. We report on initial testing of this concept with a linear chip trap fabricated by the Sandia National Labs.

Structural parameter effect of porous material on sound absorption performance of double-resonance material

NASA Astrophysics Data System (ADS)

Fan, C.; Tian, Y.; Wang, Z. Q.; Nie, J. K.; Wang, G. K.; Liu, X. S.

2017-06-01

In view of the noise feature and service environment of urban power substations, this paper explores the idea of compound impedance, fills some porous sound-absorption material in the first resonance cavity of the double-resonance sound-absorption material, and designs a new-type of composite acoustic board. We conduct some acoustic characterizations according to the standard test of impedance tube, and research on the influence of assembly order, the thickness and area density of the filling material, and back cavity on material sound-absorption performance. The results show that the new-type of acoustic board consisting of aluminum fibrous material as inner structure, micro-porous board as outer structure, and polyester-filled space between them, has good sound-absorption performance for low frequency and full frequency noise. When the thickness, area density of filling material and thickness of back cavity increase, the sound absorption coefficient curve peak will move toward low frequency.

Multi-level Simulation of a Real Time Vibration Monitoring System Component

NASA Technical Reports Server (NTRS)

Robertson, Bryan A.; Wilkerson, Delisa

2005-01-01

This paper describes the development of a custom built Digital Signal Processing (DSP) printed circuit board designed to implement the Advanced Real Time Vibration Monitoring Subsystem proposed by Marshall Space Flight Center (MSFC) Transportation Directorate in 2000 for the Space Shuttle Main Engine Advanced Health Management System (AHMS). This Real Time Vibration Monitoring System (RTVMS) is being developed for ground use as part of the AHMS Health Management Computer-Integrated Rack Assembly (HMC-IRA). The HMC-IRA RTVMS design contains five DSPs which are highly interconnected through individual communication ports, shared memory, and a unique communication router that allows all the DSPs to receive digitized data fiom two multi-channel analog boards simultaneously. This paper will briefly cover the overall board design but will focus primarily on the state-of-the-art simulation environment within which this board was developed. This 16-layer board with over 1800 components and an additional mezzanine card has been an extremely challenging design. Utilization of a Mentor Graphics simulation environment provided the unique board and system level simulation capability to ascertain any timing or functional concerns before production. By combining VHDL, Synopsys Software and Hardware Models, and the Mentor Design Capture Environment, multiple simulations were developed to verify the RTVMS design. This multi-level simulation allowed the designers to achieve complete operability without error the first time the RTVMS printed circuit board was powered. The HMC-IRA design has completed all engineering and deliverable unit testing. P

Multi-level Simulation of a Real Time Vibration Monitoring System Component

NASA Technical Reports Server (NTRS)

Roberston, Bryan; Wilkerson, DeLisa

2004-01-01

This paper describes the development of a custom built Digital Signal Processing (DSP) printed circuit board designed to implement the Advanced Real Time Vibration Monitoring Subsystem proposed by MSFC Transportation Directorate in 2000 for the Space Shuttle Main Engine Advanced Health Management System (AHMS). This Real Time Vibration Monitoring System (RTVMS) is being developed for ground use as part of the AHMS Health Management Computer-Integrated Rack Assembly (HMC-IRA). The HMC-IRA RTVMS design contains five DSPs which are highly interconnected through individual communication ports, shared memory, and a unique communication router that allows all the DSPs to receive digitized data from two multi-channel analog boards simultaneously. This paper will briefly cover the overall board design but will focus primarily on the state-of-the-art simulation environment within which this board was developed. This 16-layer board with over 1800 components and an additional mezzanine card has been an extremely challenging design. Utilization of a Mentor Graphics simulation environment provided the unique board and system level simulation capability to ascertain any timing or functional concerns before production. By combining VHDL, Synopsys Software and Hardware Models, and the Mentor Design Capture Environment, multiple simulations were developed to verify the RTVMS design. This multi-level simulation allowed the designers to achieve complete operability without error the first time the RTVMS printed circuit board was powered. The HMCIRA design has completed all engineering unit testing and the deliverable unit is currently under development.

36 CFR Appendix C to Part 1191 - Architectural Barriers Act: Scoping

Code of Federal Regulations, 2014 CFR

2014-07-01

.... That portion of a room or space where the play or practice of a sport occurs. Assembly Area. A building... devices to bypass the acoustical space between a sound source and a listener by means of induction loop, radio frequency, infrared, or direct-wired equipment. Boarding Pier. A portion of a pier where a boat is...

78 FR 7395 - Foreign-Trade Zone 129-Bellingham, WA; Notification of Proposed Production Activity; T.C. Trading...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-8-2013] Foreign-Trade Zone 129--Bellingham, WA; Notification of Proposed Production Activity; T.C. Trading Company, Inc. (Eyeglass Assembly and Kitting... activity on behalf of T.C. Trading Company, Inc. (T.C. Trading), located in Blaine, Washington. The...

Status of Higher Education in Connecticut: A Report to the Governor and General Assembly. BHE Reports.

ERIC Educational Resources Information Center

Connecticut State Board of Higher Education, Hartford.

Current data on enrollment, degrees conferred, academic programs, finances, student financial assistance, and capital facilities in Connecticut higher education institutions are summarized, and significant policy issues that the state must address on both a short-term and long-range basis are examined. Findings from the Board of Higher Education…

Annual Joint Report on Pre-Kindergarten through Higher Education in Tennessee, 2014

ERIC Educational Resources Information Center

Tennessee Higher Education Commission, 2014

2014-01-01

The "Annual Joint Report on Pre-Kindergarten through Higher Education in Tennessee" complies with the requirements established in T.C.A. Section 49-1-302(a)(10). The act directs the State Board of Education and the Tennessee Higher Education Commission to provide a report to the Governor and General Assembly, all public schools, and…

Moisture Performance of Energy-Efficient and Conventional Wood-Frame Wall Assemblies in a Mixed-Humid Climate

Treesearch

Samuel Glass; Vladimir Kochkin; S. Drumheller; Lance Barta

2015-01-01

Long-term moisture performance is a critical consideration for design and construction of building envelopes in energy-efficient buildings, yet field measurements of moisture characteristics for highly insulated wood-frame walls in mixed-humid climates are lacking. Temperature, relative humidity, and moisture content of wood framing and oriented strand board (OSB)...

The Ways of White Folks: A Love Letter to the National Education Association

ERIC Educational Resources Information Center

Lyne, Bill

2017-01-01

In July 2015, on the recommendation of the NEA Executive Committee and the NEA Board of Directors, the NEA Representative Assembly unanimously passed New Business Item B (NBI B), in which NEA declared itself ready to combat "institutional racism." The organization declared the existence of institutional racism and committed to spend more…

Lightweight Helmet For Eye/Balance Studies

NASA Technical Reports Server (NTRS)

Mcstravick, M. Catherine; Proctor, David R.; Wood, Scott J.

1988-01-01

Lightweight helmet serves as mounting platform for stimulus and sensor modules in experiments on role of vestibulo-ocular reflex in motion sickness and space-adaptation syndrome. Fitted liner and five inflatable air bladders stabilize helmet with respect to subject's head. Personal bite board attached to chin-bar assembly makes hard palate in subject's mouth serve as final position reference for helmet.

Modular space station, phase B extension. Information management advanced development. Volume 5: Software assembly

NASA Technical Reports Server (NTRS)

Gerber, C. R.

1972-01-01

The development of uniform computer program standards and conventions for the modular space station is discussed. The accomplishments analyzed are: (1) development of computer program specification hierarchy, (2) definition of computer program development plan, and (3) recommendations for utilization of all operating on-board space station related data processing facilities.

The School of the Future. Stelco Trend. Number 34 in a Series.

ERIC Educational Resources Information Center

Walker, Howard V.; Arthur, E. R.

Floor plans and illustrations present a simplified building system for an elementary school that can be utilized by any school board. All components for the system can be drawn from existing products and readily integrated with the structure. The component assembly and connections are illustrated in detail. Factory production is utilized to reduce…

Wideband monolithically integrated front-end subsystems and components

NASA Astrophysics Data System (ADS)

Mruk, Joseph Rene

This thesis presents the analysis, design, and measurements of passive, monolithically integrated, wideband recta-coax and printed circuit board front-end components. Monolithic fabrication of antennas, impedance transformers, filters, and transitions lowers manufacturing costs by reducing assembly time and enhances performance by removing connectors and cabling between the devices. Computational design, fabrication, and measurements are used to demonstrate the capabilities of these front-end assemblies. Two-arm wideband planar log-periodic antennas fed using a horizontal feed that allows for filters and impedance transformers to be readily fabricated within the radiating region of the antenna are demonstrated. At microwave frequencies, low-cost printed circuit board processes are typically used to produce planar devices. A 1.8 to 11 GHz two-arm planar log-periodic antenna is designed with a monolithically integrated impedance transformer. Band rejection methods based on modifying the antenna aperture, use of an integrated filter, and the application of both methods are investigated with realized gain suppressions of over 25 dB achieved. The ability of standard circuit board technology to fabricate millimeter-wave devices up to 110 GHz is severely limited. Thin dielectrics are required to prevent the excitation of higher order modes in the microstrip substrate. Fabricating the thin line widths required for the antenna aperture also becomes prohibitively challenging. Surface micro-machining typically used in the fabrication of MEMS devices is capable of producing the extremely small features that can be used to fabricate antennas extending through W-band. A directly RF fed 18 to 110 GHz planar log-periodic antenna is developed. The antenna is fabricated with an integrated impedance transformer and additional transitions for measurement characterization. Singly terminated low-loss wideband millimeter-wave filters operating over V- and W- band are developed. High quality performance of an 18 to 100 GHz front-end is realized by dividing the single instantaneous antenna into two apertures operating from 18 to 50 and 50 to 100 GHz. Each channel features an impedance transformer, low-pass (low-frequency) or band-pass (high-frequency) filter, and grounded CPW launch. This dual-aperture front-end demonstrates that micromachining technology is now capable of fabricating broadband millimeter-wave components with a high degree of integration.

Quantum-Well Infrared Photodetector (QWIP) Focal Plane Assembly

NASA Technical Reports Server (NTRS)

Jhabvala, Murzy; Jhabvala, Christine A.; Ewin, Audrey J.; Hess, Larry A.; Hartmann, Thomas M.; La, Anh T.

2012-01-01

A paper describes the Thermal Infrared Sensor (TIRS), a QWIP-based instrument intended to supplement the Operational Land Imager (OLI) for the Landsat Data Continuity Mission (LDCM). The TIRS instrument is a far-infrared imager operating in the pushbroom mode with two IR channels: 10.8 and 12 microns. The focal plane will contain three 640x512 QWIP arrays mounted on a silicon substrate. The silicon substrate is a custom-fabricated carrier board with a single layer of aluminum interconnects. The general fabrication process starts with a 4-in. (approx.10-cm) diameter silicon wafer. The wafer is oxidized, a single substrate contact is etched, and aluminum is deposited, patterned, and alloyed. This technology development is aimed at incorporating three large-format infrared detecting arrays based on GaAs QWIP technology onto a common focal plane with precision alignment of all three arrays. This focal plane must survive the rigors of flight qualification and operate at a temperature of 43 K (-230 C) for five years while orbiting the Earth. The challenges presented include ensuring thermal compatibility among all the components, designing and building a compact, somewhat modular system and ensuring alignment to very tight levels. The multi-array focal plane integrated onto a single silicon substrate is a new application of both QWIP array development and silicon wafer scale integration. The Invar-based assembly has been tested to ensure thermal reliability.

Improved charge injection device and a focal plane interface electronics board for stellar tracking

NASA Technical Reports Server (NTRS)

Michon, G. J.; Burke, H. K.

1984-01-01

An improved Charge Injection Device (CID) stellar tracking sensor and an operating sensor in a control/readout electronics board were developed. The sensor consists of a shift register scanned, 256x256 CID array organized for readout of 4x4 subarrays. The 4x4 subarrays can be positioned anywhere within the 256x256 array with a 2 pixel resolution. This allows continuous tracking of a number of stars simultaneously since nine pixels (3x3) centered on any star can always be read out. Organization and operation of this sensor and the improvements in design and semiconductor processing are described. A hermetic package incorporating an internal thermoelectric cooler assembled using low temperature solders was developed. The electronics board, which contains the sensor drivers, amplifiers, sample hold circuits, multiplexer, analog to digital converter, and the sensor temperature control circuits, is also described. Packaged sensors were evaluated for readout efficiency, spectral quantum efficiency, temporal noise, fixed pattern noise, and dark current. Eight sensors along with two tracker electronics boards were completed, evaluated, and delivered.

Automatic maintenance payload on board of a Mexican LEO microsatellite

NASA Astrophysics Data System (ADS)

Vicente-Vivas, Esaú; García-Nocetti, Fabián; Mendieta-Jiménez, Francisco

2006-02-01

Few research institutions from Mexico work together to finalize the integration of a technological demonstration microsatellite called Satex, aiming the launching of the first ever fully designed and manufactured domestic space vehicle. The project is based on technical knowledge gained in previous space experiences, particularly in developing GASCAN automatic experiments for NASA's space shuttle, and in some support obtained from the local team which assembled the México-OSCAR-30 microsatellites. Satex includes three autonomous payloads and a power subsystem, each one with a local microcomputer to provide intelligent and dedicated control. It also contains a flight computer (FC) with a pair of full redundancies. This enables the remote maintenance of processing boards from the ground station. A fourth communications payload depends on the flight computer for control purposes. A fifth payload was decided to be developed for the satellite. It adds value to the available on-board computers and extends the opportunity for a developing country to learn and to generate domestic space technology. Its aim is to provide automatic maintenance capabilities for the most critical on-board computer in order to achieve continuous satellite operations. This paper presents the virtual computer architecture specially developed to provide maintenance capabilities to the flight computer. The architecture is periodically implemented by software with a small amount of physical processors (FC processors) and virtual redundancies (payload processors) to emulate a hybrid redundancy computer. Communications among processors are accomplished over a fault-tolerant LAN. This allows a versatile operating behavior in terms of data communication as well as in terms of distributed fault tolerance. Obtained results, payload validation and reliability results are also presented.

Package architecture and component design for an implanted neural stimulator with closed loop control.

PubMed

Bjune, Caroline K; Marinis, Thomas F; Brady, Jeanne M; Moran, James; Wheeler, Jesse; Sriram, Tirunelveli S; Parks, Philip D; Widge, Alik S; Dougherty, Darin D; Eskandar, Emad N

2015-08-01

An implanted neural stimulator with closed loop control requires electrodes for stimulation pulses and recording neuron activity. Our system features arrays of 64 electrodes. Each electrode can be addressed through a cross bar switch, to enable it to be used for stimulation or recording. This electrode switch, a bank of low noise amplifiers with an integrated analog to digital converter, power conditioning electronics, and a communications and control gate array are co-located with the electrode array in a 14 millimeter diameter satellite package that is designed to be flush mounted in a skull burr hole. Our system features five satellite packages connected to a central hub processor-controller via ten conductor cables that terminate in a custom designed, miniaturized connector. The connector incorporates features of high reliability, military grade devices and utilizes three distinct seals to isolate the contacts from fluid permeation. The hub system is comprised of a connector header, hermetic electronics package, and rechargeable battery pack, which are mounted on and electrically interconnected by a flexible circuit board. The assembly is over molded with a compliant silicone rubber. The electronics package contains two antennas, a large coil, used for recharging the battery and a high bandwidth antenna that is used to download data and update software. The package is assembled from two machined alumina pieces, a flat base with brazed in, electrical feed through pins and a rectangular cover with rounded corners. Titanium seal rings are brazed onto these two pieces so that they can be sealed by laser welding. A third system antenna is incorporated in the flexible circuit board. It is used to communicate with an externally worn control package, which monitors the health of the system and allows both the user and clinician to control or modify various system function parameters.

A site oriented supercomputer for theoretical physics: The Fermilab Advanced Computer Program Multi Array Processor System (ACMAPS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nash, T.; Atac, R.; Cook, A.

1989-03-06

The ACPMAPS multipocessor is a highly cost effective, local memory parallel computer with a hypercube or compound hypercube architecture. Communication requires the attention of only the two communicating nodes. The design is aimed at floating point intensive, grid like problems, particularly those with extreme computing requirements. The processing nodes of the system are single board array processors, each with a peak power of 20 Mflops, supported by 8 Mbytes of data and 2 Mbytes of instruction memory. The system currently being assembled has a peak power of 5 Gflops. The nodes are based on the Weitek XL Chip set. Themore » system delivers performance at approximately $300/Mflop. 8 refs., 4 figs.« less

eSensor®: A Microarray Technology Based on Electrochemical Detection of Nucleic Acids and Its Application to Cystic Fibrosis Carrier Screening

NASA Astrophysics Data System (ADS)

Reed, Michael R.; Coty, William A.

We have developed a test for identification of carriers for cystic fibrosis using the eSensor® DNA detection technology. Oligonucleotide probes are deposited within self-assembled monolayers on gold electrodes arrayed upon printed circuit boards. These probes allow sequence-specific capture of amplicons containing a panel of mutation sites associated with cystic fibrosis. DNA targets are detected and mutations genotyped using a “sandwich” assay methodology employing electrochemical detection of ferrocene-labeled oligonucleotides for discrimination of carrier and non-carrier alleles. Performance of the cystic fibrosis application demonstrates sufficient accuracy and reliability for clinical diagnostic use, and the procedure can be performed by trained medical technologists available in the hospital laboratory.

Pressure-Sensor Assembly Technique

NASA Technical Reports Server (NTRS)

Pruzan, Daniel A.

2003-01-01

Nielsen Engineering & Research (NEAR) recently developed an ultrathin data acquisition system for use in turbomachinery testing at NASA Glenn Research Center. This system integrates a microelectromechanical- systems- (MEMS-) based absolute pressure sensor [0 to 50 psia (0 to 345 kPa)], temperature sensor, signal-conditioning application-specific integrated circuit (ASIC), microprocessor, and digital memory into a package which is roughly 2.8 in. (7.1 cm) long by 0.75 in. (1.9 cm) wide. Each of these components is flip-chip attached to a thin, flexible circuit board and subsequently ground and polished to achieve a total system thickness of 0.006 in. (0.15 mm). Because this instrument is so thin, it can be quickly adhered to any surface of interest where data can be collected without disrupting the flow being investigated. One issue in the development of the ultrathin data acquisition system was how to attach the MEMS pressure sensor to the circuit board in a manner which allowed the sensor s diaphragm to communicate with the ambient fluid while providing enough support for the chip to survive the grinding and polishing operations. The technique, developed by NEAR and Jabil Technology Services Group (San Jose, CA), is described below. In the approach developed, the sensor is attached to the specially designed circuit board, see Figure 1, using a modified flip-chip technique. The circular diaphragm on the left side of the sensor is used to actively measure the ambient pressure, while the diaphragm on the right is used to compensate for changes in output due to temperature variations. The circuit board is fabricated with an access hole through it so that when the completed system is installed onto a wind tunnel model (chip side down), the active diaphragm is exposed to the environment. After the sensor is flip-chip attached to the circuit board, the die is underfilled to support the chip during the subsequent grinding and polishing operations. To prevent this underfill material from getting onto the sensor s diaphragms, the circuit board is fabricated with two 25- micrometer-tall polymer rings, sized so that the diaphragms fit inside the rings once the chip is attached.

Adaptive Injection-locking Oscillator Array for RF Spectrum Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leung, Daniel

2011-04-19

A highly parallel radio frequency receiver using an array of injection-locking oscillators for on-chip, rapid estimation of signal amplitudes and frequencies is considered. The oscillators are tuned to different natural frequencies, and variable gain amplifiers are used to provide negative feedback to adapt the locking band-width with the input signal to yield a combined measure of input signal amplitude and frequency detuning. To further this effort, an array of 16 two-stage differential ring oscillators and 16 Gilbert-cell mixers is designed for 40-400 MHz operation. The injection-locking oscillator array is assembled on a custom printed-circuit board. Control and calibration is achievedmore » by on-board microcontroller.« less

Prototyping Instruments for Chemical Laboratory Using Inexpensive Electronic Modules.

PubMed

Urban, Pawel L

2018-05-15

Open-source electronics and programming can augment chemical and biomedical research. Currently, chemists can choose from a broad range of low-cost universal electronic modules (microcontroller boards and single-board computers) and use them to assemble working prototypes of scientific tools to address specific experimental problems and to support daily research work. The learning time can be as short as a few hours, and the required budget is often as low as 50 USD. Prototyping instruments using low-cost electronic modules gives chemists enormous flexibility to design and construct customized instrumentation, which can reduce the delays caused by limited access to high-end commercial platforms. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reliability of High I/O High Density CCGA Interconnect Electronic Packages under Extreme Thermal Environment

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni

2012-01-01

This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non-destructive inspection tools were used to assess the reliability of high density CCGA packages for deep space extreme temperature missions. Ceramic column grid array (CCGA) packages have been increasing in use based on their advantages such as high interconnect density, very good thermal and electrical performances, compatibility with standard surface-mount packaging assembly processes, and so on. CCGA packages are used in space applications such as in logic and microprocessor functions, telecommunications, payload electronics, and flight avionics. As these packages tend to have less solder joint strain relief than leaded packages or more strain relief over lead-less chip carrier packages, the reliability of CCGA packages is very important for short-term and long-term deep space missions. We have employed high density CCGA 1152 and 1272 daisy chained electronic packages in this preliminary reliability study. Each package is divided into several daisy-chained sections. The physical dimensions of CCGA1152 package is 35 mm x 35 mm with a 34 x 34 array of columns with a 1 mm pitch. The dimension of the CCGA1272 package is 37.5 mm x 37.5 mm with a 36 x 36 array with a 1 mm pitch. The columns are made up of 80% Pb/20%Sn material. CCGA interconnect electronic package printed wiring polyimide boards have been assembled and inspected using non-destructive x-ray imaging techniques. The assembled CCGA boards were subjected to extreme temperature thermal atmospheric cycling to assess their reliability for future deep space missions. The resistance of daisy-chained interconnect sections were monitored continuously during thermal cycling. This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non-destructive inspection tools were used to assess the reliability of high density CCGA packages for deep space extreme temperature missions. Keywords: Extreme temperatures, High density CCGA qualification, CCGA reliability, solder joint failures, optical inspection, and x-ray inspection.

19 CFR 10.5 - Shooks and staves; cloth boards; port director's account.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Shooks and staves produced in the United States and returned in the form of complete boxes or barrels in... country are ready to be assembled into boxes or barrels without further cutting to size; except that box shooks may be exported in double lengths and cut abroad. The number of boxes made from such shooks which...

19 CFR 10.5 - Shooks and staves; cloth boards; port director's account.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Shooks and staves produced in the United States and returned in the form of complete boxes or barrels in... country are ready to be assembled into boxes or barrels without further cutting to size; except that box shooks may be exported in double lengths and cut abroad. The number of boxes made from such shooks which...

19 CFR 10.5 - Shooks and staves; cloth boards; port director's account.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Shooks and staves produced in the United States and returned in the form of complete boxes or barrels in... country are ready to be assembled into boxes or barrels without further cutting to size; except that box shooks may be exported in double lengths and cut abroad. The number of boxes made from such shooks which...

19 CFR 10.5 - Shooks and staves; cloth boards; port director's account.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Shooks and staves produced in the United States and returned in the form of complete boxes or barrels in... country are ready to be assembled into boxes or barrels without further cutting to size; except that box shooks may be exported in double lengths and cut abroad. The number of boxes made from such shooks which...

19 CFR 10.5 - Shooks and staves; cloth boards; port director's account.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Shooks and staves produced in the United States and returned in the form of complete boxes or barrels in... country are ready to be assembled into boxes or barrels without further cutting to size; except that box shooks may be exported in double lengths and cut abroad. The number of boxes made from such shooks which...

Results through Productivity Report for Ohio Public Higher Education, 2007

ERIC Educational Resources Information Center

Ohio Board of Regents, 2007

2007-01-01

In April 2004, the Governor's Commission on Higher Education and the Economy (CHEE) recommended that the Ohio Board of Regents submit a biennial report to the Governor and the General Assembly in connection with the budget process. This report is the second such report. The purposes of this report are to provide policy makers and the public with…

Illinois Community College Board FY 2006 Adult Education and Family Literacy Report to the Governor and General Assembly

ERIC Educational Resources Information Center

Illinois Community College Board, 2007

2007-01-01

Economic and demographic changes are dramatically increasing the need for adult education, basic literacy, and English-as-a-Second Language (ESL) programs. Millions of Illinois residents lack the level of literacy skills needed to obtain good jobs, perform well on the job, and function well in an increasingly complex society. Addressing the scope…

Illinois Community College Board FY 2005 Adult Education and Family Literacy Report to the Governor and General Assembly

ERIC Educational Resources Information Center

Illinois Community College Board, 2006

2006-01-01

Economic and demographic changes are dramatically increasing the need for adult education, basic literacy, and English-as-a-Second Language (ESL) programs. Millions of Illinois residents lack the level of literacy skills needed to obtain good jobs, perform well on the job, and function well in an increasingly complex society. Addressing the scope…

An Examination of Policies, Programs, and Strategies that Address Bullying in Virginia Public School Systems

ERIC Educational Resources Information Center

Orobko, Angela Kowitz

2009-01-01

Bullying incidents in schools are getting more attention since the Columbine High School shootings on April 20, 1999 in Littleton, Colorado. Many national and state policies have been enacted since that fateful day. In Virginia, legislation passed by the 1999 General Assembly (section 22.1-208.01) required local school boards to establish a…

Altitude valve for railway suspension control system

NASA Astrophysics Data System (ADS)

Zhang, Xuan; Zhang, Lihao; Li, Qingxuan; Chen, WanSong

2017-09-01

With the variation of people and material during vehicle service, the gravity of vehicle could be unbalanced. As a result it might cause accident. In order to solve this problem, altitude valve is assembled on board. It can adjust the gravity of vehicle by the intake and outlet progress of the spring in the altitude valve to prevent the tilt of vehicles.

Prestige Planning and the Welsh Language: Marketing, the Consumer-Citizen and Language Behaviour

ERIC Educational Resources Information Center

Chriost, Diarmait Mac Giolla

2006-01-01

This paper comprises a brief examination of the approach taken by the Welsh Language Board, as the principal language policy and planning body in Wales, with regard to aspects of prestige planning and the Welsh language. It describes how devolution and the recent, and first ever, national review by the Welsh Assembly Government of Welsh language…

Evaluating print performance of Sn-Ag-Cu lead-free solder pastes used in electronics assembly process

NASA Astrophysics Data System (ADS)

Mallik, S.; Bauer, R.; Hübner, F.; Ekere, N. N.

2011-01-01

Solder paste is the most widely used interconnection material in the electronic assembly process for attaching electronic components/devices directly onto the surface of printed circuit boards, using stencil printing process. This paper evaluates the performance of three different commercially available Sn-Ag-Cu solder pastes formulated with different particle size distributions (PSD), metal content and alloy composition. A series of stencil printing tests were carried out using a specially designed stencil of 75 μm thickness and apertures of 300×300 μm2 dimension and 500 μm pitch sizes. Solder paste printing behaviors were found related to attributes such as slumping and surface tension and printing performance was correlated with metal content and PSD. The results of the study should benefit paste manufacturers and SMT assemblers to improve their products and practices.

NASA-DoD Lower Process Temperature Lead-Free Solder Project Overview

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2014-01-01

This project is a follow-on effort to the Joint Council on Aging AircraftJoint Group on Pollution Prevention (JCAAJG-PP) Pb-free Solder Project and NASA-DoD Lead-Free Electronics Project which were the first projects to test the reliability of Pb-free solder joints against the requirements of the aerospace and military community. This effort would continue to build on the results from the JCAAJG-PP Lead-Free Solder Project and NASA-DoD Lead-Free Electronics Project while focusing on a particular failure mechanism currently plaguing Pb-free assemblies, pad cratering.The NASA-DoD Lead-Free Electronics Project confirmed that pad cratering is one of the dominant failure modes that occur in various board level reliability tests, especially under dynamic loading. Pad Cratering is a latent defect that may occur during assembly, rework, and post assembly handling and testing.

International Space Station (ISS) Environmental Control and Life Support (ECLS) System Overview of Events: 2010-2014

NASA Technical Reports Server (NTRS)

Gentry, Gregory J.; Cover, John

2015-01-01

Nov 2, 2014 marked the completion of the 14th year of continuous human presence in space on board the International Space Station (ISS). After 42 expedition crews, over 115 assembly & utilization flights, over 180 combined Shuttle/Station, US & Russian Extravehicular Activities (EVAs), the post-Assembly-Complete ISS continues to fly and the engineering teams continue to learn from operating its systems, particularly the life support equipment. Problems with initial launch, assembly and activation of ISS elements have given way to more long term system operating trends. New issues have emerged, some with gestation periods measured in years. Major events and challenges for each U.S. Environmental Control and Life Support (ECLS) subsystem occurring during calendar years 2010 through 2014 are summarily discussed in this paper, along with look-aheads for what might be coming in the future for each U.S. ECLS subsystem.

Cave Pearl Data Logger: A Flexible Arduino-Based Logging Platform for Long-Term Monitoring in Harsh Environments.

PubMed

Beddows, Patricia A; Mallon, Edward K

2018-02-09

A low-cost data logging platform is presented that provides long-term operation in remote or submerged environments. Three premade "breakout boards" from the open-source Arduino ecosystem are assembled into the core of the data logger. Power optimization techniques are presented which extend the operational life of this module-based design to >1 year on three alkaline AA batteries. Robust underwater housings are constructed for these loggers using PVC fittings. Both the logging platform and the enclosures, are easy to build and modify without specialized tools or a significant background in electronics. This combination turns the Cave Pearl data logger into a generalized prototyping system and this design flexibility is demonstrated with two field studies recording drip rates in a cave and water flow in a flooded cave system. This paper describes a complete DIY solution, suitable for a wide range of challenging deployment conditions.

Common acute childhood infections and appendicitis: a historical study of statistical association in 27 English public boarding schools, 1930-1934.

PubMed

Smallman-Raynor, M R; Cliff, A D; Ord, J K

2010-08-01

Although the involvement of common childhood infections in the aetiology of acute appendicitis has long been conjectured, supporting evidence is largely restricted to a disparate set of clinical case reports. A systematic population-based analysis of the implied comorbid associations is lacking in the literature. Drawing on a classic epidemiological dataset, assembled by the School Epidemics Committee of the United Kingdom's Medical Research Council (MRC) in the 1930s, this paper presents a historical analysis of the association between termly outbreaks of each of six common childhood infections (chickenpox, measles, mumps, rubella, scarlet fever and whooping cough) and operated cases of acute appendicitis in 27 English public boarding schools. When controlled for the potential confounding effects of school, year and season, multivariate negative binomial regression revealed a positive association between the level of appendicitis activity and the recorded rate of mumps (beta=0.15, 95% CI 0.07-0.24, P<0.001). Non-significant associations were identified between appendicitis and the other sample infectious diseases. Subject to data caveats, our findings suggest that further studies are required to determine whether the comorbid association between mumps and appendicitis is causal.

An Autonomous Underwater Recorder Based on a Single Board Computer

PubMed Central

Caldas-Morgan, Manuel; Alvarez-Rosario, Alexander; Rodrigues Padovese, Linilson

2015-01-01

As industrial activities continue to grow on the Brazilian coast, underwater sound measurements are becoming of great scientific importance as they are essential to evaluate the impact of these activities on local ecosystems. In this context, the use of commercial underwater recorders is not always the most feasible alternative, due to their high cost and lack of flexibility. Design and construction of more affordable alternatives from scratch can become complex because it requires profound knowledge in areas such as electronics and low-level programming. With the aim of providing a solution; a well succeeded model of a highly flexible, low-cost alternative to commercial recorders was built based on a Raspberry Pi single board computer. A properly working prototype was assembled and it demonstrated adequate performance levels in all tested situations. The prototype was equipped with a power management module which was thoroughly evaluated. It is estimated that it will allow for great battery savings on long-term scheduled recordings. The underwater recording device was successfully deployed at selected locations along the Brazilian coast, where it adequately recorded animal and manmade acoustic events, among others. Although power consumption may not be as efficient as that of commercial and/or micro-processed solutions, the advantage offered by the proposed device is its high customizability, lower development time and inherently, its cost. PMID:26076479

Validation of a highly integrated SiPM readout system with a TOF-PET demonstrator

NASA Astrophysics Data System (ADS)

Niknejad, T.; Setayeshi, S.; Tavernier, S.; Bugalho, R.; Ferramacho, L.; Di Francesco, A.; Leong, C.; Rolo, M. D.; Shamshirsaz, M.; Silva, J. C.; Silva, R.; Silveira, M.; Zorraquino, C.; Varela, J.

2016-12-01

We have developed a highly integrated, fast and compact readout electronics for Silicon Photomultiplier (SiPM) based Time of Flight Positron Emission Tomography (TOF-PET) scanners. The readout is based on the use of TOP-PET Application Specific Integrated Circuit (PETsys TOFPET1 ASIC) with 64 channels, each with its amplifier, discriminator, Time to Digital Converter (TDC) and amplitude determination using Time Over Threshold (TOT). The ASIC has 25 ps r.m.s. intrinsic time resolution and fully digital output. The system is optimised for high rates, good timing, low power consumption and low cost. For validating the readout electronics, we have built a technical PET scanner, hereafter called ``demonstrator'', with 2'048 SiPM channels. The PET demonstrator has 16 compact Detector Modules (DM). Each DM has two ASICs reading 128 SiPM pixels in one-to-one coupling to 128 Lutetium Yttrium Orthosilicate (LYSO) crystals measuring 3.1 × 3.1 × 15 mm3 each. The data acquisition system for the demonstrator has two Front End Boards type D (FEB/D), each collecting the data of 1'024 channels (8 DMs), and transmitting assembled data frames through a serial link (4.8 Gbps), to a single Data Acquisition (DAQ) board plugged into the Peripheral Component Interconnect Express (PCIe) bus of the data acquisition PC. Results obtained with this PET demonstrator are presented.

A Tunable Terahertz Detector based on Self-Assembled Plasmonic Structure on a GaAs 2-Dimensional Electron Gas

NASA Astrophysics Data System (ADS)

Biradar, Anandrao Shesherao

The presented work in this report is about Real time Estimation of wind and analyzing current wind correction algorithm in commercial off the shelf Autopilot board. The open source ArduPilot Mega 2.5 (APM 2.5) board manufactured by 3D Robotics is used. Currently there is lot of development being done in the field of Unmanned Aerial Systems (UAVs), various aerial platforms and corresponding; autonomous systems for them. This technology has advanced to such a stage that UAVs can be used for specific designed missions and deployed with reliability. But in some areas like missions requiring high maneuverability with greater efficiency is still under research area. This would help in increasing reliability and augmenting range of UAVs significantly. One of the problems addressed through this thesis work is, current autopilot systems have algorithm that handles wind by attitude correction with appropriate Crab angle. But the real time wind vector (direction) and its calculated velocity is based on geometrical and algebraic transformation between ground speed and air speed vectors. This method of wind estimation and prediction, many a times leads to inaccuracy in attitude correction. The same has been proved in the following report with simulation and actual field testing. In later part, new ways to tackle while flying windy conditions have been proposed.

Instrumentation for laser physics and spectroscopy using 32-bit microcontrollers with an Android tablet interface

NASA Astrophysics Data System (ADS)

Eyler, E. E.

2013-10-01

Several high-performance lab instruments suitable for manual assembly have been developed using low-pin-count 32-bit microcontrollers that communicate with an Android tablet via a USB interface. A single Android tablet app accommodates multiple interface needs by uploading parameter lists and graphical data from the microcontrollers, which are themselves programmed with easily modified C code. The hardware design of the instruments emphasizes low chip counts and is highly modular, relying on small "daughter boards" for special functions such as USB power management, waveform generation, and phase-sensitive signal detection. In one example, a daughter board provides a complete waveform generator and direct digital synthesizer that fits on a 1.5 in. × 0.8 in. circuit card.

Student, Teacher, and School Performance 1995. Tenth Annual Report Submitted to the Governor and the General Assembly of the State of Tennessee.

ERIC Educational Resources Information Center

Tennessee State Board of Education, Nashville.

This report describes the performance goals established for Tennessee school systems in accordance with the Education Improvement Act (EIA) adopted in 1992. The report also describes the initiatives undertaken to assist school systems in achieving those goals. Prepared by the State Board of Education and the Commissioner of Education, this report…

Comparing the Values Hierarchy of the Kentucky Department of Education's Character/Values Task Force. Comparing a Character/Values Task Force to a National Sample.

ERIC Educational Resources Information Center

Butler, Fonda P.

In March 1989, the Kentucky Department of Education assembled a task force to make recommendations regarding the issue of teaching values and character in public schools in Kentucky. The 23-member task force represented educators, parents, the legislature, state and local school boards, law enforcement agencies, higher education, Catholic…

The Portable Art Gallery: Fostering Student Ownership and Meaningful Artmaking through Exhibiting Student Artwork

ERIC Educational Resources Information Center

Gillespie, Jethro

2014-01-01

This article describes how High School Visual Arts Teacher Jethro Gillespie built a portable art gallery for his students--essentially an 8-foot cube made from plywood and lightweight boards that can be assembled with bolts and taken apart in sections. The ceiling pieces of the gallery have track lights, the interior walls have been painted gray,…

An Analysis of Purchasing and Cooperative Agreements among School Corporations, Charter Schools, and Education Service Centers. Special Report

ERIC Educational Resources Information Center

Hiller, Stephen C.; Spradlin, Terry E.

2007-01-01

Under IC 21-10-3, the Indiana State Board of Education is required to submit a report by November 1st of each year to the state superintendent, governor, and Indiana General Assembly concerning: (1) Consolidated purchasing agreements by school corporations, charter schools, or by Education Service Centers (ESCs) on behalf of member school…

50 CFR 622.35 - Atlantic EEZ seasonal and/or area closures.

Code of Federal Regulations, 2012 CFR

2012-10-01

...°35.1′ N. lat. (due east of the NASA Vehicle Assembly Building, Cape Canaveral, FL). (b) Longline... scale NOAA chart of the location. A person aboard a vessel with a longline on board that fishes on a...-m) contour, as shown on the latest edition of NOAA chart 11460, and on the west by 80°00′ W. long...

Method of defining features on materials with a femtosecond laser

DOEpatents

Roos, Edward Victor [Los Altos, CA; Roeske, Franklin [Livermore, CA; Lee, Ronald S [Livermore, CA; Benterou, Jerry J [Livermore, CA

2006-05-23

The invention relates to a pulsed laser ablation method of metals and/or dielectric films from the surface of a wafer, printed circuit board or a hybrid substrate. By utilizing a high-energy ultra-short pulses of laser light, such a method can be used to manufacture electronic circuits and/or electro-mechanical assemblies without affecting the material adjacent to the ablation zone.

Anabolic Steroid Misuse among Minors. Report to the Governor and the General Assembly of Virginia. House Document No. 58.

ERIC Educational Resources Information Center

Virginia State Health Professions Dept., Richmond.

This document comprises the final report of the Virginia Department of Health Professions' Task Force on anabolic steroid misuse among minors. As such, it summarizes the activities of the department and of the boards within the department, the Offices of the Secretary of Health and Education, and other organizations including the Virginia High…

CheapStat: an open-source, "do-it-yourself" potentiostat for analytical and educational applications.

PubMed

Rowe, Aaron A; Bonham, Andrew J; White, Ryan J; Zimmer, Michael P; Yadgar, Ramsin J; Hobza, Tony M; Honea, Jim W; Ben-Yaacov, Ilan; Plaxco, Kevin W

2011-01-01

Although potentiostats are the foundation of modern electrochemical research, they have seen relatively little application in resource poor settings, such as undergraduate laboratory courses and the developing world. One reason for the low penetration of potentiostats is their cost, as even the least expensive commercially available laboratory potentiostats sell for more than one thousand dollars. An inexpensive electrochemical workstation could thus prove useful in educational labs, and increase access to electrochemistry-based analytical techniques for food, drug and environmental monitoring. With these motivations in mind, we describe here the CheapStat, an inexpensive (<$80), open-source (software and hardware), hand-held potentiostat that can be constructed by anyone who is proficient at assembling circuits. This device supports a number of potential waveforms necessary to perform cyclic, square wave, linear sweep and anodic stripping voltammetry. As we demonstrate, it is suitable for a wide range of applications ranging from food- and drug-quality testing to environmental monitoring, rapid DNA detection, and educational exercises. The device's schematics, parts lists, circuit board layout files, sample experiments, and detailed assembly instructions are available in the supporting information and are released under an open hardware license.

CheapStat: An Open-Source, “Do-It-Yourself” Potentiostat for Analytical and Educational Applications

PubMed Central

Rowe, Aaron A.; Bonham, Andrew J.; White, Ryan J.; Zimmer, Michael P.; Yadgar, Ramsin J.; Hobza, Tony M.; Honea, Jim W.; Ben-Yaacov, Ilan; Plaxco, Kevin W.

2011-01-01

Although potentiostats are the foundation of modern electrochemical research, they have seen relatively little application in resource poor settings, such as undergraduate laboratory courses and the developing world. One reason for the low penetration of potentiostats is their cost, as even the least expensive commercially available laboratory potentiostats sell for more than one thousand dollars. An inexpensive electrochemical workstation could thus prove useful in educational labs, and increase access to electrochemistry-based analytical techniques for food, drug and environmental monitoring. With these motivations in mind, we describe here the CheapStat, an inexpensive (<$80), open-source (software and hardware), hand-held potentiostat that can be constructed by anyone who is proficient at assembling circuits. This device supports a number of potential waveforms necessary to perform cyclic, square wave, linear sweep and anodic stripping voltammetry. As we demonstrate, it is suitable for a wide range of applications ranging from food- and drug-quality testing to environmental monitoring, rapid DNA detection, and educational exercises. The device's schematics, parts lists, circuit board layout files, sample experiments, and detailed assembly instructions are available in the supporting information and are released under an open hardware license. PMID:21931613

International Space Station Bacteria Filter Element Service Life Evaluation

NASA Technical Reports Server (NTRS)

Perry, J. L.

2005-01-01

The International Space Station (ISS) uses high-efficiency particulate air filters to remove particulate matter from the cabin atmosphere. Known as bacteria filter elements (BFEs), there are 13 elements deployed on board the ISS's U.S. segment in the flight 4R assembly level. The preflight service life prediction of 1 yr for the BFEs is based upon engineering analysis of data collected during developmental testing that used a synthetic dust challenge. While this challenge is considered reasonable and conservative from a design perspective, an understanding of the actual filter loading is required to best manage the critical ISS program resources. Testing was conducted on BFEs returned from the ISS to refine the service life prediction. Results from this testing and implications to ISS resource management are provided.

Design of a portable, intrinsically safe multichannel acquisition system for high-resolution, real-time processing HD-sEMG.

PubMed

Barone, Umberto; Merletti, Roberto

2013-08-01

A compact and portable system for real-time, multichannel, HD-sEMG acquisition is presented. The device is based on a modular, multiboard approach for scalability and to optimize power consumption for battery operating mode. The proposed modular approach allows us to configure the number of sEMG channels from 64 to 424. A plastic-optical-fiber-based 10/100 Ethernet link is implemented on a field-programmable gate array (FPGA)-based board for real-time, safety data transmission toward a personal computer or laptop for data storage and offline analysis. The high-performance A/D conversion stage, based on 24-bit ADC, allows us to automatically serialize the samples and transmits them on a single SPI bus connecting a sequence of up to 14 ADC chips in chain mode. The prototype is configured to work with 64 channels and a sample frequency of 2.441 ksps (derived from 25-MHz clock source), corresponding to a real data throughput of 3 Mbps. The prototype was assembled to demonstrate the available features (e.g., scalability) and evaluate the expected performances. The analog front end board could be dynamically configured to acquire sEMG signals in monopolar or single differential mode by means of FPGA I/O interface. The system can acquire continuously 64 channels for up to 5 h with a lightweight battery pack of 7.5 Vdc/2200 mAh. A PC-based application was also developed, by means of the open source Qt Development Kit from Nokia, for prototype characterization, sEMG measurements, and real-time visualization of 2-D maps.

Flexible hybrid circuit fully inkjet-printed: Surface mount devices assembled by silver nanoparticles-based inkjet ink

NASA Astrophysics Data System (ADS)

Arrese, J.; Vescio, G.; Xuriguera, E.; Medina-Rodriguez, B.; Cornet, A.; Cirera, A.

2017-03-01

Nowadays, inkjet-printed devices such as transistors are still unstable in air and have poor performances. Moreover, the present electronics applications require a high degree of reliability and quality of their properties. In order to accomplish these application requirements, hybrid electronics is fulfilled by combining the advantages of the printing technologies with the surface-mount technology. In this work, silver nanoparticle-based inkjet ink (AgNP ink) is used as a novel approach to connect surface-mount devices (SMDs) onto inkjet-printed pads, conducted by inkjet printing technology. Excellent quality AgNP ink-junctions are ensured with high resolution picoliter drop jetting at low temperature (˜150 °C). Electrical, mechanical, and morphological characterizations are carried out to assess the performance of the AgNP ink junction. Moreover, AgNP ink is compared with common benchmark materials (i.e., silver epoxy and solder). Electrical contact resistance characterization shows a similar performance between the AgNP ink and the usual ones. Mechanical characterization shows comparable shear strength for AgNP ink and silver epoxy, and both present higher adhesion than solder. Morphological inspections by field-emission scanning electron microscopy confirm a high quality interface of the silver nanoparticle interconnection. Finally, a flexible hybrid circuit on paper controlled by an Arduino board is manufactured, demonstrating the viability and scalability of the AgNP ink assembling technique.

The thin-wall tube drift chamber operating in vacuum (prototype)

NASA Astrophysics Data System (ADS)

Alexeev, G. D.; Glonti, L. N.; Kekelidze, V. D.; Malyshev, V. L.; Piskun, A. A.; Potrbenikov, Yu. K.; Rodionov, V. K.; Samsonov, V. A.; Tokmenin, V. V.; Shkarovskiy, S. N.

2013-08-01

The goal of this work was to design drift tubes and a chamber operating in vacuum, and to develop technologies for tubes independent assembly and mounting in the chamber. These design and technology were tested on the prototype. The main features of the chamber are the following: the drift tubes are made of flexible mylar film (wall thickness 36 μm, diameter 9.80 mm, length 2160 mm) using ultrasonic welding along the generatrix; the welding device and methods were developed at JINR. Drift tubes with end plugs, anode wires and spacers were completely assembled outside the chamber. "Self-centering" spacers and bushes were used for precise setting of the anode wires and tubes. The assembled tubes were sealed with O-rings in their seats in the chamber which simplified the chamber assembling. Moreover the tube assembly and the chamber manufacture can be performed independently and in parallel; this sufficiently reduces the total time of chamber manufacture and assembling, its cost and allows tubes to be tested outside the chamber. The technology of independent tube assembling is suitable for a chamber of any shape but a round chamber is preferable for operation in vacuum. Single channel amplifier-discriminator boards which are more stable against cross talks were used for testing the tubes. Independently assembled tubes were mounted into the chamber prototype and its performance characteristic measured under the vacuum conditions. The results showed that both the structure and the tubes themselves normally operate. They are suitable for making a full-scale drift chamber for vacuum.

Alkaline static feed electrolyzer based oxygen generation system

NASA Technical Reports Server (NTRS)

Noble, L. D.; Kovach, A. J.; Fortunato, F. A.; Schubert, F. H.; Grigger, D. J.

1988-01-01

In preparation for the future deployment of the Space Station, an R and D program was established to demonstrate integrated operation of an alkaline Water Electrolysis System and a fuel cell as an energy storage device. The program's scope was revised when the Space Station Control Board changed the energy storage baseline for the Space Station. The new scope was aimed at the development of an alkaline Static Feed Electrolyzer for use in an Environmental Control/Life Support System as an oxygen generation system. As a result, the program was divided into two phases. The phase 1 effort was directed at the development of the Static Feed Electrolyzer for application in a Regenerative Fuel Cell System. During this phase, the program emphasized incorporation of the Regenerative Fuel Cell System design requirements into the Static Feed Electrolyzer electrochemical module design and the mechanical components design. The mechanical components included a Pressure Control Assembly, a Water Supply Assembly and a Thermal Control Assembly. These designs were completed through manufacturing drawing during Phase 1. The Phase 2 effort was directed at advancing the Alkaline Static Feed Electrolyzer database for an oxygen generation system. This development was aimed at extending the Static Feed Electrolyzer database in areas which may be encountered from initial fabrication through transportation, storage, launch and eventual Space Station startup. During this Phase, the Program emphasized three major areas: materials evaluation, electrochemical module scaling and performance repeatability and Static Feed Electrolyzer operational definition and characterization.

Report of the Seasat Failure Review Board

NASA Technical Reports Server (NTRS)

Lundin, Bruce T.

1978-01-01

The Seasat spacecraft failed on October 9, 1978, after satisfactory operation in orbit for 105 days, as a result of a loss of electrical power in the Agena bus that was used as a part of the spacecraft. This loss of power was caused by a massive and progressive short in one of the slip ring assemblies that was used to connect the rotating solar arrays into the power subsystem. The most likely cause of this short was the initiation of an arc between adjacent slip ring brush assemblies. The triggering mechanism of this arc could have been either a wire-to-brush assembly contact, a brush-to-brush contact, or a momentary short caused by a contaminant that bridged internal components of opposite electrical polarity. The slip ring assembly, as used in the Seasat spacecraft, was connected into the power subsystem in such a way that most of the adjacent brush assemblies were of opposite electrical polarity. This wiring arrangement, together with the congested nature of the design itself, made the Seasat slip ring assembly a unique, first-of-a-kind component that was particularly prone to shorting. The possibility of slip ring failures resulting from placing opposite electrical polarities on adjacent brush assemblies was known at least as early-as the summer of 1977 to other projects within the contractor's organization. Furthermore, failures of slip ring assemblies due to shorting between brushes had been experienced by the prime contractor on slip ring assemblies used by other programs. That the Seasat organization was not fully aware of these potential failure modes was due to a breakdown in communication within the contractor's organization.

Moisture Durability with Vapor-Permeable Insulating Sheathing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, R.; Lstiburek, J.

2013-09-01

Exterior sheathing insulation is an effective strategy in increasing the overall R-value of wall assemblies; other benefits include decreasing the effects of thermal bridging and increasing the moisture durability of the built assembly. Vapor-permeable exterior insulation, such as mineral board or expanded polystyrene foam, are one such product that may be used to achieve these benefits. However,uncertainty exists on the effects of inward driven moisture and the interaction of increased sheathing temperatures on the moisture durability of the edifice. To address these concerns, Building Science Corporation (BSC) conducted a series of hygrothermal models for cities representing a range of differentmore » climate zones. This report describes the research project, key research questions, and theprocedures utilized to analyse the problems.« less

Moisture Durability with Vapor-Permeable Insulating Sheathing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, R.; Lstiburek, J.

2013-09-01

Exterior sheathing insulation is an effective strategy in increasing the overall R-value of wall assemblies; other benefits include decreasing the effects of thermal bridging and increasing the moisture durability of the built assembly. Vapor-permeable exterior insulation, such as mineral board or expanded polystyrene foam, are one such product that may be used to achieve these benefits. However, uncertainty exists on the effects of inward driven moisture and the interaction of increased sheathing temperatures on the moisture durability of the edifice. To address these concerns, Building Science Corporation (BSC) conducted a series of hygrothermal models for cities representing a range ofmore » different climate zones. This report describes the research project, key research questions, and the procedures utilized to analyse the problems.« less

Some implications of remanufacturing hardwood lumber

Treesearch

Charles J. Gatchell; R. Edward Thomas; Elizabeth S. Walker

2000-01-01

Research on several hundred well-manufactured 1 and 2A Common red oak boards shows that better edging and/or trimming or division-based remanufacturing can produce boards of higher grade and value. Division-based remanufacturing divides a board into as many as four smaller boards. The UGRS computer program (3,4) grades digitized boards, examines their remanufacturing...

Vision Technology for Automated Inspection of Hybrid Microelectronics Assemblies

DTIC Science & Technology

1988-06-01

circuits are a very efficient packaging technique, with the primary advantages of size, better resistance to environ - 0 ments, and the flexibility to...produced for the military are much more complex and have more stringent performance requirements, particularly in their resistance to environments and...boards, particularly because of the need to protect circuits from a hostile environment such as salt, heat, and moisture. Included among the major U.S

Commuter Air Carrier Loan Guarantee Study.

DTIC Science & Technology

1980-01-01

Aircraft on Order o Financial Statements o Profit & Loss Statement " Balance Sheet o Financial Position Change Statement o General Topics o Reasons...financial data on commuters is very limited, it was necessary to assemble information from a number of sources such as the (divil Aeronautics Board...PROGRAM Assisted by SMS Associates of Washington, D.C., Aerospace has: (1) developed current acquisition and operating cost data on new, used, and planned

Evaluation Transportability Testing of the Joint Modular Intermodal Platform (JMIP) Unit #4, TP-94-01, Transportability Testing Procedures

DTIC Science & Technology

2007-07-01

447 3893 VSN: NL1FR5 MFG Serial #: T-018447EFJM Weight: 19,340 lbs 3-1 5. Semitrailer, flatbed , breakbulk/container transporter, 22.5 ton Model...CHAFTING PIECE, 118" X 6" X 40" PLYWOOD, (I REaD). LAMINATE TO BEARING PIECE W16-6d NAILS EVENLY SPACED. SIDE STRAPPING BOARD ASSEMBLY (2 REOD) (I

The search for CFC alternatives is over?

NASA Technical Reports Server (NTRS)

Crawford, Tim

1995-01-01

The Electronics Manufacturing Productivity Facility (EMPF) is a U.S. Navy Center of Excellence tasked to do research in electronics manufacturing. For the past seven years, the EMPF has performed extensive research in various cleaning materials and processes that have recently been made available to printed circuit board assemblers. This paper outlines our research and points out the positive and negative aspects that need to be considered when choosing an alternative process.

Complexity in College Admission: Fact or Urban Myth. Research Findings of Parent and Student Perceptions of Complexity in College Admission

ERIC Educational Resources Information Center

College Board Advocacy & Policy Center, 2010

2010-01-01

In September 2007, the College Board formed the Task Force on Admissions in the 21st Century in response to a request from the Guidance and Admission Assembly Council (GAA Council) to more closely examine the high-school-to-college transition process. Each spring, at the conclusion of the college admission cycle, there is much discussion in the…

Placement accuracy gauge for electrical components and method of using same

DOEpatents

Biggs, Peter M.; Dancer, Linda K.; Yerganian, Simon S.

1988-10-11

Surface mounted electrical components are typically assembled on printed wiring boards by automatic machines. It is important that the machines accurately move with respect to both X and Y rotational axes in order to insure that components are positioned precisely on connector pads of the printed wiring board being assembled. In accordance with the instant invention, a gauge is used to facilitate convenient accuracy checks. The gauge is a glass substrate on which grids of 0.005 inch lines are scribed to form location and orientation fields where components are to be placed. The grids are referenced from either fiducial marks or the edge of the substrate to establish known positions within the grids. The equipment to be evaluated is programmed to place components in known positions and the components are held in place by tacky adhesive that is sprayed on the substrate prior to placing the components. The accuracy of the component position is then compared to the programmed position by placing the substrate on a light table and observing the component location. If a significant inaccuracy with respect to any of the axes exists, the inaccuracy is apparent because the component is not aligned properly with the grid. If a precise measurement of an axis inaccuracy is desired, a measuring microscope may be utilized.

Thermal Diagnostics with the Atmospheric Imaging Assembly on board the Solar Dynamics Observatory: A Validated Method for Differential Emission Measure Inversions

NASA Astrophysics Data System (ADS)

Cheung, Mark C. M.; Boerner, P.; Schrijver, C. J.; Testa, P.; Chen, F.; Peter, H.; Malanushenko, A.

2015-07-01

We present a new method for performing differential emission measure (DEM) inversions on narrow-band EUV images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory. The method yields positive definite DEM solutions by solving a linear program. This method has been validated against a diverse set of thermal models of varying complexity and realism. These include (1) idealized Gaussian DEM distributions, (2) 3D models of NOAA Active Region 11158 comprising quasi-steady loop atmospheres in a nonlinear force-free field, and (3) thermodynamic models from a fully compressible, 3D MHD simulation of active region (AR) corona formation following magnetic flux emergence. We then present results from the application of the method to AIA observations of Active Region 11158, comparing the region's thermal structure on two successive solar rotations. Additionally, we show how the DEM inversion method can be adapted to simultaneously invert AIA and Hinode X-ray Telescope data, and how supplementing AIA data with the latter improves the inversion result. The speed of the method allows for routine production of DEM maps, thus facilitating science studies that require tracking of the thermal structure of the solar corona in time and space.

Placement accuracy gauge for electrical components and method of using same

DOEpatents

Biggs, P.M.; Dancer, L.K.; Yerganian, S.S.

1987-11-12

Surface mounted electrical components are typically assembled on printed wiring board by automatic machines. It is important that the machines accurately move with respect to both X and Y rotational axes in order to insure that components are positioned precisely on connector pads of the printed wiring board being assembled. In accordance with the instant invention, a gauge is used to facilitate convenient accuracy checks. The gauge is a glass substrate on which grids of 0.005 inch lines are scribed to form location and orientation fields where components are to be placed. The grids are referenced from ether fiducial marks or the edge of the substrate to establish known positions within the grids. The equipment to be evaluated is programmed to place components in known positions and the components are held in place by tacky adhesive that is sprayed on the substrate prior to placing the components. The accuracy of the component position is then compared to the programmed position by placing the substrate on a light table and observing the component location. If a significant inaccuracy with respect to any of the axes exists, the inaccuracy is apparent because the component is not aligned properly with the grid. If a precise measurement of an axis inaccuracy is desired, a measuring microscope may be utilized. 6 figs.

Compact electro-optical module with polymer waveguides on a flexible substrate for high-density board-level communication

NASA Astrophysics Data System (ADS)

Weiss, J. R. M.; Lamprecht, T.; Meier, N.; Dangel, R.; Horst, F.; Jubin, D.; Beyeler, R.; Offrein, B. J.

2010-02-01

We report on the co-packaging of electrical CMOS transceiver and VCSEL chip arrays on a flexible electrical substrate with optical polymer waveguides. The electro-optical components are attached to the substrate edge and butt-coupled to the waveguides. Electrically conductive silver-ink connects them to the substrate at an angle of 90°. The final assembly contacts the surface of a package laminate with an integrated compressible connector. The module can be folded to save space, requires only a small footprint on the package laminate and provides short electrical high-speed signal paths. With our approach, the electro-optical package becomes a compact electro-optical module with integrated polymer waveguides terminated with either optical connectors (e.g., at the card edge) or with an identical assembly for a second processor on the board. Consequently, no costly subassemblies and connectors are needed, and a very high integration density and scalability to virtually arbitrary channel counts and towards very high data rates (20+ Gbps) become possible. Future cost targets of much less than US$1 per Gbps will be reached by employing standard PCB materials and technologies that are well established in the industry. Moreover, our technology platform has both electrical and optical connectivity and functionality.

THERMAL DIAGNOSTICS WITH THE ATMOSPHERIC IMAGING ASSEMBLY ON BOARD THE SOLAR DYNAMICS OBSERVATORY: A VALIDATED METHOD FOR DIFFERENTIAL EMISSION MEASURE INVERSIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheung, Mark C. M.; Boerner, P.; Schrijver, C. J.

We present a new method for performing differential emission measure (DEM) inversions on narrow-band EUV images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory. The method yields positive definite DEM solutions by solving a linear program. This method has been validated against a diverse set of thermal models of varying complexity and realism. These include (1) idealized Gaussian DEM distributions, (2) 3D models of NOAA Active Region 11158 comprising quasi-steady loop atmospheres in a nonlinear force-free field, and (3) thermodynamic models from a fully compressible, 3D MHD simulation of active region (AR) corona formation following magneticmore » flux emergence. We then present results from the application of the method to AIA observations of Active Region 11158, comparing the region's thermal structure on two successive solar rotations. Additionally, we show how the DEM inversion method can be adapted to simultaneously invert AIA and Hinode X-ray Telescope data, and how supplementing AIA data with the latter improves the inversion result. The speed of the method allows for routine production of DEM maps, thus facilitating science studies that require tracking of the thermal structure of the solar corona in time and space.« less

WE-EF-BRA-01: A Dual-Use Optical Tomography System for Small Animal Radiation Research Platform (SARRP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, K; Bin, Z; Wong, J

Purpose: We develop a novel dual-use configuration for a tri-modality, CBCT/bioluminescence tomography(BLT)/fluorescence tomography(FT), imaging system with the SARRP that can function as a standalone system for longitudinal imaging research and on-board the SARRP to guide irradiation. BLT provides radiation guidance for soft tissue target, while FT offers functional information allowing mechanistic investigations. Methods: The optical assembly includes CCD camera, lens, filter wheel, 3-way mirrors, scanning fiber system and light-tight enclosure. The rotating mirror system directs the optical signal from the animal surface to the camera at multiple projection over 180 degree. The fiber-laser system serves as the external light sourcemore » for the FT application. Multiple filters are used for multispectral imaging to enhance localization accuracy using BLT. SARRP CBCT provides anatomical information and geometric mesh for BLT/FT reconstruction. To facilitate dual use, the 3-way mirror system is cantilevered in front of the camera. The entire optical assembly is driven by a 1D linear stage to dock onto an independent mouse support bed for standalone application. After completion of on-board optical imaging, the system is retracted from the SARRP to allow irradiation of the mouse. Results: A tissue-simulating phantom and a mouse model with a luminescence light source are used to demonstrate the function of the dual-use optical system. Feasibility data have been obtained based on a manual-docking prototype. The center of mass of light source determined in living mouse with on-board BLT is within 1±0.2mm of that with CBCT. The performance of the motorized system is expected to be the same and will be presented. Conclusion: We anticipate the motorized dual use system provide significant efficiency gain over our manual docking and off-line system. By also supporting off-line longitudinal studies independent of the SARRP, the dual-use system is a highly efficient and cost-effective platform to facilitate optical imaging for pre-clinical radiation research. The work is supported by NIH R01CA158100 and Xstrahl Ltd. Drs. John Wong and Iulian Iordachita receive royalty payment from a licensing agreement between Xstrahl Ltd and Johns Hopkins University. John Wong also has a consultant agreement with Xstrahl Ltd.« less

Method Of Packaging And Assembling Electro-Microfluidic Devices

DOEpatents

Benavides, Gilbert L.; Galambos, Paul C.; Emerson, John A.; Peterson, Kenneth A.; Giunta, Rachel K.; Zamora, David Lee; Watson, Robert D.

2004-11-23

A new architecture for packaging surface micromachined electro-microfluidic devices is presented. This architecture relies on two scales of packaging to bring fluid to the device scale (picoliters) from the macro-scale (microliters). The architecture emulates and utilizes electronics packaging technology. The larger package consists of a circuit board with embedded fluidic channels and standard fluidic connectors (e.g. Fluidic Printed Wiring Board). The embedded channels connect to the smaller package, an Electro-Microfluidic Dual-Inline-Package (EMDIP) that takes fluid to the microfluidic integrated circuit (MIC). The fluidic connection is made to the back of the MIC through Bosch-etched holes that take fluid to surface micromachined channels on the front of the MIC. Electrical connection is made to bond pads on the front of the MIC.

Orbiter fire rescue and crew escape training for EVA crew systems support

NASA Image and Video Library

1993-01-28

Photos of orbiter fire rescue and crew escape training for extravehicular activity (EVA) crew systems support conducted in Bldg 9A Crew Compartment Trainer (CCT) and Fuel Fuselage Trainer (FFT) include views of CCT interior of middeck starboard fuselage showing middeck forward (MF) locker and COAS assembly filter, artiflex film and camcorder bag (26834); launch/entry suit (LES) helmet assembly, neckring and helmet hold-down assembly (26835-26836); middeck aft (MA) lockers (26837); area of middeck airlock and crew escape pole (26838); connectors of crew escape pole in the middeck (268390); three test subjects in LES in the flight deck (26840); emergency side hatch slide before inflated stowage (26841); area of below adjacent to floor panel MD23R (26842); a test subject in LES in the flight deck (26843); control board and also showing sign of "orbital maneuvering system (OMS) secure and OMS TK" (26844); test subject in the flight deck also showing chart of "ascent/abort summary" (26845).

Working Boards in Tertiary Education: Lessons from Three Case Studies. Professional File. Number 25

ERIC Educational Resources Information Center

Lang, Daniel W.

2005-01-01

There are a number of studies that classify governing boards into different types. Some classifications are based on management form. Some are based on the form in which authority is exercised. Some are based on the form of institution that the board serves. Most of these classifications include "working boards," but few offer a clear…

Space to Space Advanced EMU Radio

NASA Technical Reports Server (NTRS)

Maicke, Andrew

2016-01-01

The main task for this project was the development of a prototype for the Space to Space Advanced EMU Radio (SSAER). The SSAER is an updated version of the Space to Space EMU Radio (SSER), which is the current radio used by EMUs (Extravehicular Mobility Unit) for communication between suits and with the ISS. The SSER was developed in 1999, and it was desired to update the design used in the system. Importantly, besides replacing out-of-production parts it was necessary to decrease the size of the radio due to increased volume constraints with the updated Portable Life Support System (PLSS) 2.5, which will be attached on future space suits. In particular, it was desired to fabricate a PCB for the front-end of the prototype SSAER system. Once this board was manufactured and all parts assembled, it could then be tested for quality of operation as well as compliancy with the SSER required specifications. Upon arrival, a small outline of the target system was provided, and it was my responsibility to take that outline to a finished, testable board. This board would include several stages, including frequency mixing, amplification, modulation, demodulation, and handled both the transmit and receive lines of the radio. I developed a new design based on the old SSER system and the outline provided to me, and found parts to fit the tasks in my design. It was also important to consider the specifications of the SSER, which included the system noise figure, gain, and power consumption. Further, all parts needed to be impedance matched, and spurious signals needed to be avoided. In order to fulfill these two requirements, it was necessary to perform some calculations using a Smith Chart and excel analysis. Once all parts were selected, I drew the schematics for the system in Altium Designer. This included developing schematic symbols, as well as layout. Once the schematic was finished, it was then necessary to lay the parts out onto a PCB using Altium. Similar to the schematic design, in order to accomplish this it was necessary to develop component land patterns and add component 3D models. All of this was achieved, and the PCB is currently in review. After it is finished being reviewed, this board will be sent out for manufacture. All electronic components used in the PCB have been acquired, and once the board arrives they will be soldered onto the board using a machine in building 44. Finally, the board will be tested for performance on-site. This will likely be accomplished by the end of the internship.

Reliability of Sn/Pb and Lead-Free (SnAgCu) Solders of Surface Mounted Miniaturized Passive Components for Extreme Temperature (-185 C to +125 C) Space Missions

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni

2011-01-01

Surface mount electronic package test boards have been assembled using tin/lead (Sn/Pb) and lead-free (Pb-free or SnAgCu or SAC305) solders. The soldered surface mount packages include ball grid arrays (BGA), flat packs, various sizes of passive chip components, etc. They have been optically inspected after assembly and subsequently subjected to extreme temperature thermal cycling to assess their reliability or future deep space, long-term, extreme temperature environmental missions. In this study, the employed temperature range (-185oC to +125oC) covers military specifications (-55oC to +100oC), extreme old Martian (-120oC to +115oC), asteroid Nereus (-180oC to +25oC) and JUNO (-150oC to +120oC) environments. The boards were inspected at room temperature and at various intervals as a function of extreme temperature thermal cycling and bake duration. Electrical resistance measurements made at room temperature are reported and the tests to date have shown some change in resistance as a function of extreme temperature thermal cycling and some showed increase in resistance. However, the change in interconnect resistance becomes more noticeable with increasing number of thermal cycles. Further research work will be carried out to understand the reliability of packages under extreme temperature applications (-185oC to +125oC) via continuously monitoring the daisy chain resistance for BGA, Flat-packs, lead less chip packages, etc. This paper will describe the experimental reliability results of miniaturized passive components (01005, 0201, 0402, 0603, 0805, and 1206) assembled using surface mounting processes with tin-lead and lead-free solder alloys under extreme temperature environments.

Reliability of Sn/Pb and lead-free (SnAgCu) solders of surface mounted miniaturized passive components for extreme temperature (-185°C to +125°C) space missions

NASA Astrophysics Data System (ADS)

Ramesham, Rajeshuni

2011-02-01

Surface mount electronic package test boards have been assembled using tin/lead (Sn/Pb) and lead-free (Pb-free or SnAgCu or SAC305) solders. The soldered surface mount packages include ball grid arrays (BGA), flat packs, various sizes of passive chip components, etc. They have been optically inspected after assembly and subsequently subjected to extreme temperature thermal cycling to assess their reliability for future deep space, long-term, extreme temperature environmental missions. In this study, the employed temperature range (-185°C to +125°C) covers military specifications (-55°C to +100°C), extreme cold Martian (-120°C to +115°C), asteroid Nereus (-180°C to +25°C) and JUNO (-150°C to +120°C) environments. The boards were inspected at room temperature and at various intervals as a function of extreme temperature thermal cycling and bake duration. Electrical resistance measurements made at room temperature are reported and the tests to date have shown some change in resistance as a function of extreme temperature thermal cycling and some showed increase in resistance. However, the change in interconnect resistance becomes more noticeable with increasing number of thermal cycles. Further research work will be carried out to understand the reliability of packages under extreme temperature applications (-185°C to +125°C) via continuously monitoring the daisy chain resistance for BGA, Flat-packs, lead less chip packages, etc. This paper will describe the experimental reliability results of miniaturized passive components (01005, 0201, 0402, 0603, 0805, and 1206) assembled using surface mounting processes with tin-lead and lead-free solder alloys under extreme temperature environments.

Impact of Isothermal Aging and Testing Temperature on Large Flip-Chip BGA Interconnect Mechanical Shock Performance

NASA Astrophysics Data System (ADS)

Lee, Tae-Kyu; Chen, Zhiqiang; Guirguis, Cherif; Akinade, Kola

2017-10-01

The stability of solder interconnects in a mechanical shock environment is crucial for large body size flip-chip ball grid array (FCBGA) electronic packages. Additionally, the junction temperature increases with higher electric power condition, which brings the component into an elevated temperature environment, thus introducing another consideration factor for mechanical stability of interconnection joints. Since most of the shock performance data available were produced at room temperature, the effect of elevated temperature is of interest to ensure the reliability of the device in a mechanical shock environment. To achieve a stable␣interconnect in a dynamic shock environment, the interconnections must tolerate mechanical strain, which is induced by the shock wave input and reaches the particular component interconnect joint. In this study, large body size (52.5 × 52.5 mm2) FCBGA components assembled on 2.4-mm-thick boards were tested with various isothermal pre-conditions and testing conditions. With a heating element embedded in the test board, a test temperature range from room temperature to 100°C was established. The effects of elevated temperature on mechanical shock performance were investigated. Failure and degradation mechanisms are identified and discussed based on the microstructure evolution and grain structure transformations.

A Comparison of Fission Power System Options for Lunar and Mars Surface Applications

NASA Technical Reports Server (NTRS)

Mason, Lee S.

2006-01-01

This paper presents a comparison of reactor and power conversion design options for 50 kWe class lunar and Mars surface power applications with scaling from 25 to 200 kWe. Design concepts and integration approaches are provided for three reactor-converter combinations: gas-cooled Brayton, liquid-metal Stirling, and liquid-metal thermoelectric. The study examines the mass and performance of low temperature, stainless steel based reactors and higher temperature refractory reactors. The preferred system implementation approach uses crew-assisted assembly and in-situ radiation shielding via installation of the reactor in an excavated hole. As an alternative, self-deployable system concepts that use earth-delivered, on-board radiation shielding are evaluated. The analyses indicate that among the 50 kWe stainless steel reactor options, the liquid-metal Stirling system provides the lowest mass at about 5300 kg followed by the gas-cooled Brayton at 5700 kg and the liquid-metal thermoelectric at 8400 kg. The use of a higher temperature, refractory reactor favors the gas-cooled Brayton option with a system mass of about 4200 kg as compared to the Stirling and thermoelectric options at 4700 and 5600 kg, respectively. The self-deployed concepts with on-board shielding result in a factor of two system mass increase as compared to the in-situ shielded concepts.

1060-nm VCSEL-based parallel-optical modules for optical interconnects

NASA Astrophysics Data System (ADS)

Nishimura, N.; Nagashima, K.; Kise, T.; Rizky, A. F.; Uemura, T.; Nekado, Y.; Ishikawa, Y.; Nasu, H.

2015-03-01

The capability of mounting a parallel-optical module onto a PCB through solder-reflow process contributes to reduce the number of piece parts, simplify its assembly process, and minimize a foot print for both AOC and on-board applications. We introduce solder-reflow-capable parallel-optical modules employing 1060-nm InGaAs/GaAs VCSEL which leads to the advantages of realizing wider modulation bandwidth, longer transmission distance, and higher reliability. We demonstrate 4-channel parallel optical link performance operated at a bit stream of 28 Gb/s 231-1 PRBS for each channel and transmitted through a 50-μm-core MMF beyond 500 m. We also introduce a new mounting technology of paralleloptical module to realize maintaining good coupling and robust electrical connection during solder-reflow process between an optical module and a polymer-waveguide-embedded PCB.

Creating Mechanisms for Meaningful Collaboration Between Members of Urban Communities and University-Based HIV Prevention Researchers.

PubMed

McKay, Mary M; Hibbert, Richard; Lawrence, Rita; Miranda, Ana; Paikoff, Roberta; Bell, Carl C; Madison-Boyd, Sybil; Baptiste, Donna; Coleman, Doris; Pinto, Rogério M; Bannon, William M

2007-01-01

This article provides a description of a Community/University Collaborative Board, a formalized partnership between representatives from an inner-city community and university-based researchers. This Collaborative Board oversees a number of research projects focused on designing, delivering and testing family-based HIV prevention and mental health focused programs to elementary and junior high school age youth and their families. The Collaborative Board consists of urban parents, school staff members, representatives from community-based agencies and university-based researchers. One research project, the CHAMP (Collaborative HIV prevention and Adolescent Mental health Project) Family Program Study, an urban, family-based HIV prevention project will be used to illustrate how the Collaborative Board oversees a community-based research study. The process of establishing a Collaborative Board, recruiting members and developing subcommittees is described within this article. Examples of specific issues addressed by the Collaborative Board within its subcommittees, Implementation, Finance, Welcome, Research, Grant writing, Curriculum, and Leadership, are detailed in this article along with lessons learned.

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures.

PubMed

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

A pressure core ultrasonic test system for on-board analysis of gas hydrate-bearing sediments under in situ pressures

NASA Astrophysics Data System (ADS)

Yang, Lei; Zhou, Weihua; Xue, Kaihua; Wei, Rupeng; Ling, Zheng

2018-05-01

The enormous potential as an alternative energy resource has made natural gas hydrates a material of intense research interest. Their exploration and sample characterization require a quick and effective analysis of the hydrate-bearing cores recovered under in situ pressures. Here a novel Pressure Core Ultrasonic Test System (PCUTS) for on-board analysis of sediment cores containing gas hydrates at in situ pressures is presented. The PCUTS is designed to be compatible with an on-board pressure core transfer device and a long gravity-piston pressure-retained corer. It provides several advantages over laboratory core analysis including quick and non-destructive detection, in situ and successive acoustic property acquisition, and remission of sample storage and transportation. The design of the unique assembly units to ensure the in situ detection is demonstrated, involving the U-type protecting jackets, transducer precession device, and pressure stabilization system. The in situ P-wave velocity measurements make the detection of gas hydrate existence in the sediments possible on-board. Performance tests have verified the feasibility and sensitivity of the ultrasonic test unit, showing the dependence of P-wave velocity on gas hydrate saturation. The PCUTS has been successfully applied for analysis of natural samples containing gas hydrates recovered from the South China Sea. It is indicated that on-board P-wave measurements could provide a quick and effective understanding of the hydrate occurrence in natural samples, which can assist further resource exploration, assessment, and subsequent detailed core analysis.

AUTOMATING THREE DIMENSIONAL (3D) MODEL CREATION OF CIRCUIT CARD ASSEMBLIES

DTIC Science & Technology

2017-07-01

are those of the author(s) and should not be construed as an official Department of the Army position, policy, or decision, unless so designated by...other documentation. The citation in this report of the names of commercial firms or commercially available products or services does not...document describes a method to export data from a printed wiring board computer-aided design (CAD) application and then import that data to a

Comments on the California Community Colleges' Plan for Allocating Board Financial Assistance to Community College Students: A Report to the Fiscal and Educational Policy Committees of the Legislature.

ERIC Educational Resources Information Center

California State Postsecondary Education Commission, Sacramento.

In January 1984, the California State Legislature adopted Assembly Bill (AB) 1XX, which included provisions for a mandatory student fee and an appropriation for financial aid to offset that fee. This report by the California Postsecondary Education Commission (CPEC) describes the provisions of AB 1XX and the community college financial aid plan,…

FY 2015 Adult Education and Family Literacy: Report to the Governor and General Assembly. A Summary of Programs and Activities during the Fiscal Year July 1, 2014 through June 30, 2015

ERIC Educational Resources Information Center

Illinois Community College Board, 2016

2016-01-01

The Illinois Community College Board (ICCB) continues to build and expand opportunities for adult education students to transition into college and the workforce. Through the Workforce Innovation and Opportunity Act (WIOA), the ICCB will better align services with the core partners to assist students in accessing career pathway instructional and…

Establishment of Production Cleanliness Criteria and Processes for Printed Wiring Boards and Assemblies.

DTIC Science & Technology

1981-12-01

H (hydrogen) and He (helium) are excluded since they have no outer shell electrons to eject. If the thin film analysis capability of Auger is...comtaminant profiling (C/P) system instrumentation will detect and intepret the amounts of contaminant species in an extract in terms of parts-per-billion...Nadas, and P. Fennell Evans, J. Phys. Chem;, 74 (1970), 4572. 215 4’. FILMED 7 4-85 DTIC

Miniature and Molecularly Specific Optical Screening Technologies for Breast Cancer

DTIC Science & Technology

2006-10-01

modeling of the heat dissipation effects of compact LEDs on tissue samples, selection of multiwavelength compact light sources, calculating bandwidth...Opto Technology also designs custom chip on board assemblies with single and multiple wavelengths of UV , Visible and IR LED die (365 – 940 nm...reflectance with high signal to noise for optical properties typical of tissue in the UV -VIS. We have furthermore investigated the potential use of LEDs as

Examining the technology acceptance for dismantling of waste printed circuit boards in light of recycling and environmental concerns.

PubMed

Duan, Huabo; Hou, Kun; Li, Jinhui; Zhu, Xiaodong

2011-03-01

The dismantling of printed circuit board assemblies (PCBAs) and the recovery of their useful materials can lead to serious environmental impacts mainly due to their complicated physical structure and the variety of toxic elements contained in their material composition. So far, less attention has been paid to their responsible recycling compared to that of bare printed circuit boards. Combined with other materials recovery process, proper dismantling of PCBAs is beneficial to conserve scarce resources, reuse the components, and eliminate or safely dispose of hazardous materials. In analyzing the generation, resources potential and hazardous risk of scrap PCBAs, technologies used for the dismantling of waste PCBAs have been widely investigated and reviewed from the aspects of both industrial application and laboratory-scale studies. In addition, the feasibility of PCBA dismantling has been discussed, the determinants of which, including the heating conditions and mechanical properties have been identified. Moreover, this paper evaluates the environmental consequences caused by the dismantling of PCBAs. Copyright © 2010 Elsevier Ltd. All rights reserved.

Rotating pressure measurement system using an on board calibration standard

NASA Technical Reports Server (NTRS)

Senyitko, Richard G.; Blumenthal, Philip Z.; Freedman, Robert J.

1991-01-01

A computer-controlled multichannel pressure measurement system was developed to acquire detailed flow field measurements on board the Large Low Speed Centrifugal Compressor Research Facility at the NASA Lewis Research Center. A pneumatic slip ring seal assembly is used to transfer calibration pressures to a reference standard transducer on board the compressor rotor in order to measure very low differential pressures with the high accuracy required. A unique data acquisition system was designed and built to convert the analog signal from the reference transducer to the variable frequency required by the multichannel pressure measurement system and also to provide an output for temperature control of the reference transducer. The system also monitors changes in test cell barometric pressure and rotating seal leakage and provides an on screen warning to the operator if limits are exceeded. The methods used for the selection and testing of the the reference transducer are discussed, and the data acquisition system hardware and software design are described. The calculated and experimental data for the system measurement accuracy are also presented.

A Coronal Hole Jet Observed with Hinode and the Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Young, Peter H.; Muglach, Karin

2014-01-01

A small blowout jet was observed at the boundary of the south coronal hole on 2011 February 8 at around 21:00 UT. Images from the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory (SDO) revealed an expanding loop rising from one footpoint of a compact, bipolar bright point. Magnetograms from the Helioseismic Magnetic Imager (HMI) on board SDO showed that the jet was triggered by the cancelation of a parasitic positive polarity feature near the negative pole of the bright point. The jet emission was present for 25 mins and it extended 30 Mm from the bright point. Spectra from the EUV Imaging Spectrometer on board Hinode yielded a temperature and density of 1.6 MK and 0.9-1.7 × 10( exp 8) cu cm for the ejected plasma. Line-of-sight velocities reached up to 250 km/s. The density of the bright point was 7.6 × 10(exp 8) cu cm, and the peak of the bright point's emission measure occurred at 1.3 MK, with no plasma above 3 MK.

A cross-disciplinary response to improve test activities: The corporate memory capitalization in Ariane4 test domain

NASA Technical Reports Server (NTRS)

Vo, Dinh Phuoc; Soler, Christian; Aussenac, N.; Macchion, D.

1993-01-01

The Assembly, Integration, Test, and Validation (AIT/AIV) of the Ariane4 Vehicle Equipment Bay was held at Matra Marconi Space (MMS) site of Toulouse for several years. For this activity, incident interpretation necessitates a great deal of different knowledge. When complex faults occur, particularly those appearing during overall control tests, experts of various domains (EGSE, software, on-board equipment) have to join for investigation sessions. Thus, an assistance tool for the identification of faulty equipment will improve the efficiency of diagnosis and the overall productivity of test activities. As a solution, the Aramiihs laboratory proposed considering the opportunity of a knowledge based system intended to assist the tester in diagnosis. This knowledge based system is, in fact, a short-term achievement of a long-term goal which is the capitalization of corporate memory in the Ariane4 test domain. Aramiihs is a research unit where engineers from MMS and researchers from the IRIT-CNRS cooperate on problems concerning new types of man-system interaction.

Pressure-equalizing PV assembly and method

DOEpatents

Dinwoodie, Thomas L.

2004-10-26

Each PV assembly of an array of PV assemblies comprises a base, a PV module and a support assembly securing the PV module to a position overlying the upper surface of the base. Vents are formed through the base. A pressure equalization path extends from the outer surface of the PV module, past the PV module, to and through at least one of the vents, and to the lower surface of the base to help reduce wind uplift forces on the PV assembly. The PV assemblies may be interengaged, such as by interengaging the bases of adjacent PV assemblies. The base may include a main portion and a cover and the bases of adjacent PV assemblies may be interengaged by securing the covers of adjacent bases together.

Packaging Technology Designed, Fabricated, and Assembled for High-Temperature SiC Microsystems

NASA Technical Reports Server (NTRS)

Chen, Liang-Yu

2003-01-01

A series of ceramic substrates and thick-film metalization-based prototype microsystem packages designed for silicon carbide (SiC) high-temperature microsystems have been developed for operation in 500 C harsh environments. These prototype packages were designed, fabricated, and assembled at the NASA Glenn Research Center. Both the electrical interconnection system and the die-attach scheme for this packaging system have been tested extensively at high temperatures. Printed circuit boards used to interconnect these chip-level packages and passive components also are being fabricated and tested. NASA space and aeronautical missions need harsh-environment, especially high-temperature, operable microsystems for probing the inner solar planets and for in situ monitoring and control of next-generation aeronautical engines. Various SiC high-temperature-operable microelectromechanical system (MEMS) sensors, actuators, and electronics have been demonstrated at temperatures as high as 600 C, but most of these devices were demonstrated only in the laboratory environment partially because systematic packaging technology for supporting these devices at temperatures of 500 C and beyond was not available. Thus, the development of a systematic high-temperature packaging technology is essential for both in situ testing and the commercialization of high-temperature SiC MEMS. Researchers at Glenn developed new prototype packages for high-temperature microsystems using ceramic substrates (aluminum nitride and 96- and 90-wt% aluminum oxides) and gold (Au) thick-film metalization. Packaging components, which include a thick-film metalization-based wirebond interconnection system and a low-electrical-resistance SiC die-attachment scheme, have been tested at temperatures up to 500 C. The interconnection system composed of Au thick-film printed wire and 1-mil Au wire bond was tested in 500 C oxidizing air with and without 50-mA direct current for over 5000 hr. The Au thick-film metalization-based wirebond electrical interconnection system was also tested in an extremely dynamic thermal environment to assess thermal reliability. The I-V curve1 of a SiC high-temperature diode was measured in oxidizing air at 500 C for 1000 hr to electrically test the Au thick-film material-based die-attach assembly.

Effects of PCB Substrate Surface Finish, Flux, and Phosphorus Content on Ionic Contamination

NASA Astrophysics Data System (ADS)

Bacior, M.; Sobczak, N.; Siewiorek, A.; Kudyba, A.; Homa, M.; Nowak, R.; Dziula, M.; Masłoń, S.

2015-02-01

The ionic contamination on printed circuit boards (PCB) having different surface finishes was examined using ionograph. The study was performed at the RT on three types of PCBs covered with: (i) hot air solder leveling (HASL LF), (ii) electroless nickel immersion gold (ENIG), and (iii) organic surface protectant (OSP), all on Cu substrates, as well as two types of fluxes, namely EF2202 and RF800. In the group of boards without soldered components, the lowest average value of contamination was for the ENIG 18 µm surface (0.01 μg NaCl/cm2). Boards with soldered components were more contaminated (from 0.29 μg NaCl/cm2 for the HASL LF 18 µm surface). After spraying boards with fluxing agents, the values of contaminants were the highest. The influence of phosphorus content in Ni-P layer of ENIG finish on ionic contamination was examined. In the group of PCBs with Au coating, the smallest amount of surface contaminants (0.32 μg NaCl/cm2) was for Ni-2-5%P layer. PCBs with Ni-11%P layer were higher contaminated (0.47 μg NaCl/cm2), and another with Ni-8%P layer had 0.81 μg NaCl/cm2. PCBs without Au coating, had the lowest contamination (0.48 μg NaCl/cm2) at phosphorous content equal 11%P. Higher contamination (0.67 μg NaCl/cm2) was at 2-5%P, up to 1.98 μg NaCl/cm2 for 8% of P. Boards with Au finish have lower value of contamination than identical boards without Au layer thus contributing to better reliability of electronic assemblies, since its failures due to current leakage and corrosion can be caused by contaminants.

One-Step Laser Patterned Highly Uniform Reduced Graphene Oxide Thin Films for Circuit-Enabled Tattoo and Flexible Humidity Sensor Application.

PubMed

Park, Rowoon; Kim, Hyesu; Lone, Saifullah; Jeon, Sangheon; Kwon, Young Woo; Shin, Bosung; Hong, Suck Won

2018-06-06

The conversion of graphene oxide (GO) into reduced graphene oxide (rGO) is imperative for the electronic device applications of graphene-based materials. Efficient and cost-effective fabrication of highly uniform GO films and the successive reduction into rGO on a large area is still a cumbersome task through conventional protocols. Improved film casting of GO sheets on a polymeric substrate with quick and green reduction processes has a potential that may establish a path to the practical flexible electronics. Herein, we report a facile deposition process of GO on flexible polymer substrates to create highly uniform thin films over a large area by a flow-enabled self-assembly approach. The self-assembly of GO sheets was successfully performed by dragging the trapped solution of GO in confined geometry, which consisted of an upper stationary blade and a lower moving substrate on a motorized translational stage. The prepared GO thin films could be selectively reduced and facilitated from the simple laser direct writing process for programmable circuit printing with the desired configuration and less sample damage due to the non-contact mode operation without the use of photolithography, toxic chemistry, or high-temperature reduction methods. Furthermore, two different modes of the laser operating system for the reduction of GO films turned out to be valuable for the construction of novel graphene-based high-throughput electrical circuit boards compatible with integrating electronic module chips and flexible humidity sensors.

Thin glass based packaging and photonic single-mode waveguide integration by ion-exchange technology on board and module level

NASA Astrophysics Data System (ADS)

Brusberg, Lars; Lang, Günter; Schröder, Henning

2011-01-01

The proposed novel packaging approach merges micro-system packaging and glass integrated optics. It provides 3D optical single-mode intra system links to bridge the gap between novel photonic integrated circuits and the glass fibers for inter system interconnects. We introduce our hybrid 3D photonic packaging approach based on thin glass substrates with planar integrated optical single-mode waveguides for fiber-to-chip and chip-to-chip links. Optical mirrors and lenses provide optical mode matching for photonic IC assemblies and optical fiber interconnects. Thin glass is commercially available in panel and wafer formats and characterizes excellent optical and high-frequency properties as reviewed in the paper. That makes it perfect for micro-system packaging. The adopted planar waveguide process based on ion-exchange technology is capable for high-volume manufacturing. This ion-exchange process and the optical propagation are described in detail for thin glass substrates. An extensive characterization of all basic circuit elements like straight and curved waveguides, couplers and crosses proves the low attenuation of the optical circuit elements.

Optical system for the Protein Crystallisation Diagnostics Facility (PCDF) on board the ISS

NASA Astrophysics Data System (ADS)

Joannes, Luc; Dupont, Olivier; Dewandel, Jean-Luc; Ligot, Renaud; Algrain, Hervé

2004-06-01

The Protein Crystallisation Diagnostic Facility (PCDF) is a multi-user facility to study the protein crystallisation under the conditions of micro-gravity onboard the International Space Station (ISS) Columbus facility. Large size protein crystals will growth under reduced gravity in thermally controlled reactors. A combination of diagnostic tools like video system, microscope, interferometer, and light scattering device shall help to understand the growth phenomena. Common methods of protein crystallisation shall be performed in PCDF: Dialysis where the protein solution and the salt solution are separated by a semi-permeable membrane. Extended Length Dialysis Batch where the saturation to get crystals is achieved by changing the concentration of the protein in the sample liquid. The overall ESA project is leaded by EADS Space Transportation, Friedrichshafen, Germany. Lambda-X is responsible for the Optical System (OS), with Verhaert Design and Development as sub-contractor for the mechanical design. The OS includes different compact parts: Original illumination systems based on LEDs of difference colours; Quantitative Mach-Zehnder interferometers to measure the concentration distribution around crystals; Imaging assemblies to visualize the protein volume with different field of views. The paper concentrates on the description of each part, and in particular on the imaging assembly which allow switching from one field of view to another by passive elements only.

Radiated Emissions from a Remote-Controlled Airplane-Measured in a Reverberation Chamber

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Koppen, Sandra V.; Nguyen, Truong X.; Dudley, Kenneth L.; Szatkowski, George N.; Quach, Cuong C.; Vazquez, Sixto L.; Mielnik, John J.; Hogge, Edward F.; Hill, Boyd L.;

Pressure equalizing photovoltaic assembly and method

DOEpatents

Dinwoodie, Thomas L [Piedmont, CA

2003-05-27

Each PV assembly of an array of PV assemblies comprises a base, a PV module and a support assembly securing the PV module to a position overlying the upper surface of the base. Vents are formed through the base. A pressure equalization path extends from the outer surface of the PV module, past the peripheral edge of the PV module, to and through at least one of the vents, and to the lower surface of the base to help reduce wind uplift forces on the PV assembly. The PV assemblies may be interengaged, such as by interengaging the bases of adjacent PV assemblies. The base may include a main portion and a cover and the bases of adjacent PV assemblies may be interengaged by securing the covers of adjacent bases together.

Radiator debris removing apparatus and work machine using same

DOEpatents

Martin, Kevin L [Washburn, IL; Elliott, Dwight E [Chillicothe, IL

2008-09-02

A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

Engineering Management Board tour Vehicle Assembly Building (VAB)

NASA Image and Video Library

2017-03-22

All the heads of engineering from across the country come together at KSC for a bi-annual face to face meeting to discuss roles, progress and capabilities. The two day meeting helps to ensure a unified focus in all engineering endevours, especially those that involve intercenter collaboration such as upcoming launch of SLS and Orion. The group toured level 1 and 28 of highbay 3 of the VAB on Wednesday, March 22 to look over the newly installed platforms.

The Coast Artillery Journal. Volume 59, Number 2, August 1923

DTIC Science & Technology

1923-08-01

writers and artists have used it as a device for Joan of Arc. Heraldically the phoenix is always represented as an eagle rising from flames, and in...181) THE BULLETI~ BOARD 185 graphs of two artistic pieces in sterling silver which have just been completed by the Bailey Banks and Biddle Company...the supper hour the gatheriIU! again assembled on the parade ground to "itness a demonstration of cornbin~ gymnastics and calisthenics by the entire

High-Performance Energy-Efficient Cool Metal Roof Assemblies Utilizing Building Integrated Renewable Solar Energy Technologies for New and Retrofit Building Construction

DTIC Science & Technology

2014-04-01

technology described in this proposal was first commercialized in 2004. It has been installed in 35 states and 5 countries primarily on residential ...temperatures. o Rainwater harvesting systems help reduce demands on potable water systems and help crowded cities manage stormwater drainage problems...of high density polyisocyanurate rigid insulation board installed over the existing roof and between the sub-purlins with the top layer taped to

Introduction to LNG vehicle safety

NASA Astrophysics Data System (ADS)

Bratvold, Delma; Friedman, David; Chernoff, Harry; Farkhondehpay, Dariush; Comay, Claudia

1994-03-01

Basic information on the characteristics of liquefied natural gas (LNG) is assembled to provide an overview of safety issues and practices for the use of LNG vehicles. This document is intended for those planning or considering the use of LNG vehicles, including vehicle fleet owners and operators, public transit officials and boards, local fire and safety officials, manufacturers and distributors, and gas industry officials. Safety issues and mitigation measures that should be considered for candidate LNG vehicle projects are addressed.

LANDSAT-D flight segment operations manual, volume 1

NASA Technical Reports Server (NTRS)

Varhola, J.

1982-01-01

Hardware, systems, and subsystems for the multimission modular spacecraft used for LANDSAT 4 are described and depicted in block diagrams and schematics. Components discussed include the modular attitude control system; the communication and data handling subsystem; the narrowband tape recorder; the on-board computer; the propulsion module subsystem; the signal conditioning and control unit; the modular power subsystem; the solar array drive and power transmission assembly; the power distribution unit; the digital processing unit; and the wideband communication subsystem.

Failure Mechanisms of Thermomechanically Loaded SnAgCu/Plastic Core Solder Ball Composite Joints in Low-Temperature Co-Fired Ceramic/Printed Wiring Board Assemblies

NASA Astrophysics Data System (ADS)

Nousiainen, O.; Putaala, J.; Kangasvieri, T.; Rautioaho, R.; Vähäkangas, J.

2007-03-01

The thermal fatigue endurance of completely lead-free 95.5Sn4Ag0.7Cu/plastic core solder ball (PCSB) composite joint structures in low-temperature Co-fired ceramic/printed wiring board (LTCC/PWB) assemblies was investigated using thermal cycling tests over the temperature ranges of -40°C 125°C and 0°C 100°C. Two separate creep/fatigue failures initiated and propagated in the joints during the tests: (1) a crack along the intermetallic compound (IMC)/solder interface on the LTCC side of the joint, which formed at the high-temperature extremes; and (2) a crack in the solder near the LTCC solder land, which formed at the low-temperature extremes. Moreover, localized recrystallization was detected at the outer edge of the joints that were tested in the harsh (-40°C 125°C) test conditions. The failure mechanism was creep/fatigue-induced mixed intergranular and transgranular cracking in the recrystallized zone, but it was dominated by transgranular thermal fatigue failure beyond the recrystallized zone. The change in the failure mechanism increased the rate of crack growth. When the lower temperature extreme was raised from -40°C to 0°C, no recrystallized zone was detected and the failure was due to intergranular cracks.

The GNC Measurement System for the Automated Transfer Vehicle

NASA Astrophysics Data System (ADS)

Roux, Y.; da Cunha, P.

The Automated Transfer Vehicle (ATV) is a European Space Agency (ESA) funded spacecraft developed by EADS Space Transportation as prime contractor for the space segment together with major European industrial partners, in the frame of the International Space Station (ISS). Its mission objective is threefold : to supply the station with fret and propellant, to reboost ISS to a higher orbit and to dispose of waste from the station. The ATV first flight, called Jules Verne and planned on 2005, will be the first European Vehicle to perform an orbital rendezvous. The GNC Measurement System (GMS) is the ATV on board function in charge of the measurement data collection and preconditioning for the navigation, guidance and control (GNC) algorithms. The GMS is made up of hardware which are the navigation sensors (with a certain level of hardware redundancy for each of them), and of an on-board software that manages, monitors and performs consistency checks to detect and isolate potential sensor failures. The GMS relies on six kinds of navigation sensors, used during various phases of the mission : the gyrometers assembly (GYRA), the accelerometers assembly (ACCA), the star trackers (STR), the GPS receivers, the telegoniometers (TGM) and the videometers (VDM), the last two being used for the final rendezvous phase. The GMS function is developed by EADS Space Transportation together with other industrial partners: EADS Astrium, EADS Sodern, Laben and Dasa Jena Optronik.

Board Level Proton Testing Book of Knowledge for NASA Electronic Parts and Packaging Program

NASA Technical Reports Server (NTRS)

Guertin, Steven M.

2017-01-01

This book of knowledge (BoK) provides a critical review of the benefits and difficulties associated with using proton irradiation as a means of exploring the radiation hardness of commercial-off-the-shelf (COTS) systems. This work was developed for the NASA Electronic Parts and Packaging (NEPP) Board Level Testing for the COTS task. The fundamental findings of this BoK are the following. The board-level test method can reduce the worst case estimate for a board's single-event effect (SEE) sensitivity compared to the case of no test data, but only by a factor of ten. The estimated worst case rate of failure for untested boards is about 0.1 SEE/board-day. By employing the use of protons with energies near or above 200 MeV, this rate can be safely reduced to 0.01 SEE/board-day, with only those SEEs with deep charge collection mechanisms rising this high. For general SEEs, such as static random-access memory (SRAM) upsets, single-event transients (SETs), single-event gate ruptures (SEGRs), and similar cases where the relevant charge collection depth is less than 10 µm, the worst case rate for SEE is below 0.001 SEE/board-day. Note that these bounds assume that no SEEs are observed during testing. When SEEs are observed during testing, the board-level test method can establish a reliable event rate in some orbits, though all established rates will be at or above 0.001 SEE/board-day. The board-level test approach we explore has picked up support as a radiation hardness assurance technique over the last twenty years. The approach originally was used to provide a very limited verification of the suitability of low cost assemblies to be used in the very benign environment of the International Space Station (ISS), in limited reliability applications. Recently the method has been gaining popularity as a way to establish a minimum level of SEE performance of systems that require somewhat higher reliability performance than previous applications. This sort of application of the method suggests a critical analysis of the method is in order. This is also of current consideration because the primary facility used for this type of work, the Indiana University Cyclotron Facility (IUCF) (also known as the Integrated Science and Technology (ISAT) hall), has closed permanently, and the future selection of alternate test facilities is critically important. This document reviews the main theoretical work on proton testing of assemblies over the last twenty years. It augments this with review of reported data generated from the method and other data that applies to the limitations of the proton board-level test approach. When protons are incident on a system for test they can produce spallation reactions. From these reactions, secondary particles with linear energy transfers (LETs) significantly higher than the incident protons can be produced. These secondary particles, together with the protons, can simulate a subset of the space environment for particles capable of inducing single event effects (SEEs). The proton board-level test approach has been used to bound SEE rates, establishing a maximum possible SEE rate that a test article may exhibit in space. This bound is not particularly useful in many cases because the bound is quite loose. We discuss the established limit that the proton board-level test approach leaves us with. The remaining possible SEE rates may be as high as one per ten years for most devices. The situation is actually more problematic for many SEE types with deep charge collection. In cases with these SEEs, the limits set by the proton board-level test can be on the order of one per 100 days. Because of the limited nature of the bounds established by proton testing alone, it is possible that tested devices will have actual SEE sensitivity that is very low (e.g., fewer than one event in 1 × 10(exp 4) years), but the test method will only be able to establish the limits indicated above. This BoK further examines other benefits of proton board-level testing besides hardness assurance. The primary alternate use is the injection of errors. Error injection, or fault injection, is something that is often done in a simulation environment. But the proton beam has the benefit of injecting the majority of actual SEEs without risk of something being missed, and without the risk of simulation artifacts misleading the SEE investigation.

Optimization of a large-area detector-block based on SiPM and pixelated LYSO crystal arrays.

PubMed

Calva-Coraza, E; Alva-Sánchez, H; Murrieta-Rodríguez, T; Martínez-Dávalos, A; Rodríguez-Villafuerte, M

2017-10-01

We present the performance evaluation of a large-area detector module based on the ArrayC-60035-64P, an 8×8 array of tileable, 7.2mm pitch, silicon photomultipliers (SiPM) by SensL, covering a total area of 57.4mm×57.4mm. We characterized the ArrayC-60035-64P, operating at room temperature, using LYSO pixelated crystal arrays of different pitch sizes (1.075, 1.430, 1.683, 2.080 and 2.280mm) to determine the resolvable crystal size. After an optimization process, a 7mm thick coupling light guide was used for all crystal pitches. To identify the interaction position a 16-channel (8 columns, 8 rows) symmetric charge division (SCD) readout board together with a center-of-gravity algorithm was used. Based on this, we assembled the detector modules using a 40×40 LYSO, 1.43mm pitch array, covering the total detector area. Calibration was performed using a 137 Cs source resulting in excellent crystal maps with minor geometric distortion, a mean 4.1 peak-to-valley ratio and 9.6% mean energy resolution for 662keV photons in the central region. The resolvability index was calculated in the x and y directions with values under 0.42 in all cases. We show that these large area SiPM arrays, combined with a 16-channel SCD readout board, can offer high spatial resolution, without processing a big number of signals, attaining excellent energy resolution and detector uniformity. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

The Generalization of Rook Number r2 for the Fractal Chessboard

NASA Astrophysics Data System (ADS)

Sangeetha, R.; Jayalalitha, G.

2018-04-01

In this paper we develop a generalized formula of r 2, the number of ways of placing two non-attacking Rooks for the Fractal Chessboard which is defined as a board that grows progressively in a consistent manner using a 2 × 2 chessboard to its sides and corners. The board is disintegrated into small sub boards based on their position in the whole Fractal Chessboard (FC). The board is disintegrated into sub boards based on their position in the whole board FC. By finding the value of r 2 for each of these sub boards and adding them, the r 2 value of the whole board FC is obtained. Finally the r 2 value is generalized the Fractal Chessboard at any iteration I ≥ 4 .

Vehicle Assembly Building Fire Mishap Investigation Report. Volume I of V

NASA Technical Reports Server (NTRS)

Kight, Ira; Luciano, Steven; Stevens, Michael B.; Farley, W. Max; Collins, Bryce D.; Potterger, William C.; Levesque, Jodi

2005-01-01

On January 13, 2005, at approximately 1355, smoke was noticed on the 4th floor of D Tower in the Vehicle Assembly Building (VAB). Subsequently, a 911 call was made, a fire alarm pull station was activated, and the VAB was evacuated. The source of the smoke was determined to be a fire on the Low Bay M/N section roof near the Launch Control Center (LCC) Crossover. Due to the high visibility of the mishap, the KSC Center Director appointed a Mishap Investigation Board. Damage to government property was limited to the roof and a small number of ceiling tiles that were damaged by the fire fighters during the response. At the time of the mishap, there were hazardous commodities in the VAB including Solid Rocket Motors (SRMs) with open grain due to Solid Rocket Booster (SRB) igniter inspections. The Board agrees with the SGS Fire Services' theory that large amounts of smoke concentrated in the VAB D Tower and moved downward into the cable tunnel. The Board determined the proximate cause of this incident to be torching. HRI was installing a torch applied roof membrane which resulted in the ignition of combustible materials under the membrane near a wooden roof expansion joint. The torch applied roofing method is a universally accepted safe industry practice when applied to non-combustible surfaces. The combination of an open flame torch and combustible materiaLs presents an increased level of risk even with skilled applicators. The addition of high winds to this combination results in a risk the Board thinks can not be adequately mitigated. An appropriate risk assessment and analysis must be performed on the proposed roofing method to be used on high visibility facilities which represent unique national assets even when using common industry practices for repair and modification. The Board identified three root causes which contributed to or created the proximate cause and, if eliminated or modified, would have prevented the mishap: 1. Combustible materials in existing roof system 2. Wind speed and direction 3. Inadequate fire watch technique. Two contributing factors were identified which may have contributed to the occurrence but, if eliminated or modified, would not have prevented the occurrence: 1. HRI rushed to dry in and seal the roof on January 13 because heavy rain was predicted for the next day 2. No guidance on torching in windy conditions A total of 17 significant observations were noted during this investigation, which could lead to another mishap, or increase the severity of a mishap, but were not contributing factors in this mishap.

78 FR 26770 - MeadWestvaco Coated Board, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-08

... Coated Board, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for Blanket Section 204 Authorization This is a supplemental notice in the above-referenced proceeding of MeadWestvaco Coated Board, LLC's application for market-based rate authority, with an accompanying rate schedule...

Panel Board From Coconut Fibre And Pet Bottle

NASA Astrophysics Data System (ADS)

Ngadiman, Norhayati; Kaamin, Masiri; Abd. Kadir, Aslila; Sahat, Suhaila; Zaini, Aziza; Raihana Nor Zentan, Siti; Ain Ahmad, Nur; Amran, Wan Haizatul Aisyhah Wan

2018-03-01

The rate of global deforestation and its impact on the environment has led particle board manufacture to search for alternative feedstock, especially in countries where wood is less available compared to other cellulosic natural product. Based on the properties of coconut fibre and PET bottle, these two materials can be recycle as raw material for manufacture of panel board. As for this study, the coconut fibre were used as the filler and PET bottle as outer lining of the panel board. Two types of coconut fibre were used which are grinding and un-grinding coconut fibre. At first, the coconut fibre are undergoes softening, grinding, drying and sieving process, while PET bottle was cleaning, shredding, sieving before compacted using hydraulic hot press machine. There are four types of testing that been carried out which are swelling, water absorption, Modulus of Elasticity (MOE) and Modulus of Rupture (MOR). The result show the conventional board has the highest value for MOE test, so it's indicate that the conventional board is less strength from the coconut fibre board. As for water absorption test, the average water absorption of coconut fibre based panel board is less than conventional board. Overall, the coconut fibre board is better than conventional panel board because coconut fibre board are less swelling, has low water absorption, high modulus of rupture and low modulus of elasticity. Based on the finding, this coconut fibre panel board has potential as a stronger and long-lasting panel board than the conventional board in the market. Other than that, the panel also have their own aesthetic value since the recycled plastic bottle used as outer lining is colourful and giving aesthetic value.

Autonomous mobile robot for radiologic surveys

DOEpatents

Dudar, A.M.; Wagner, D.G.; Teese, G.D.

1994-06-28

An apparatus is described for conducting radiologic surveys. The apparatus comprises in the main a robot capable of following a preprogrammed path through an area, a radiation monitor adapted to receive input from a radiation detector assembly, ultrasonic transducers for navigation and collision avoidance, and an on-board computer system including an integrator for interfacing the radiation monitor and the robot. Front and rear bumpers are attached to the robot by bumper mounts. The robot may be equipped with memory boards for the collection and storage of radiation survey information. The on-board computer system is connected to a remote host computer via a UHF radio link. The apparatus is powered by a rechargeable 24-volt DC battery, and is stored at a docking station when not in use and/or for recharging. A remote host computer contains a stored database defining paths between points in the area where the robot is to operate, including but not limited to the locations of walls, doors, stationary furniture and equipment, and sonic markers if used. When a program consisting of a series of paths is downloaded to the on-board computer system, the robot conducts a floor survey autonomously at any preselected rate. When the radiation monitor detects contamination, the robot resurveys the area at reduced speed and resumes its preprogrammed path if the contamination is not confirmed. If the contamination is confirmed, the robot stops and sounds an alarm. 5 figures.

Autonomous mobile robot for radiologic surveys

DOEpatents

Dudar, Aed M.; Wagner, David G.; Teese, Gregory D.

1994-01-01

An apparatus for conducting radiologic surveys. The apparatus comprises in the main a robot capable of following a preprogrammed path through an area, a radiation monitor adapted to receive input from a radiation detector assembly, ultrasonic transducers for navigation and collision avoidance, and an on-board computer system including an integrator for interfacing the radiation monitor and the robot. Front and rear bumpers are attached to the robot by bumper mounts. The robot may be equipped with memory boards for the collection and storage of radiation survey information. The on-board computer system is connected to a remote host computer via a UHF radio link. The apparatus is powered by a rechargeable 24-volt DC battery, and is stored at a docking station when not in use and/or for recharging. A remote host computer contains a stored database defining paths between points in the area where the robot is to operate, including but not limited to the locations of walls, doors, stationary furniture and equipment, and sonic markers if used. When a program consisting of a series of paths is downloaded to the on-board computer system, the robot conducts a floor survey autonomously at any preselected rate. When the radiation monitor detects contamination, the robot resurveys the area at reduced speed and resumes its preprogrammed path if the contamination is not confirmed. If the contamination is confirmed, the robot stops and sounds an alarm.

Test-Analysis Correlation for Space Shuttle External Tank Foam Impacting RCC Wing Leading Edge Component Panels

NASA Technical Reports Server (NTRS)

Lyle, Karen H.

2008-01-01

The Space Shuttle Columbia Accident Investigation Board recommended that NASA develop, validate, and maintain a modeling tool capable of predicting the damage threshold for debris impacts on the Space Shuttle Reinforced Carbon-Carbon (RCC) wing leading edge and nosecap assembly. The results presented in this paper are one part of a multi-level approach that supported the development of the predictive tool used to recertify the shuttle for flight following the Columbia Accident. The assessment of predictive capability was largely based on test analysis comparisons for simpler component structures. This paper provides comparisons of finite element simulations with test data for external tank foam debris impacts onto 6-in. square RCC flat panels. Both quantitative displacement and qualitative damage assessment correlations are provided. The comparisons show good agreement and provided the Space Shuttle Program with confidence in the predictive tool.

Engineering aspects and hardware verification of a volume producable solid oxide fuel cell stack design for diesel auxiliary power units

NASA Astrophysics Data System (ADS)

Stelter, Michael; Reinert, Andreas; Mai, Björn Erik; Kuznecov, Mihail

A solid oxide fuel cell (SOFC) stack module is presented that is designed for operation on diesel reformate in an auxiliary power unit (APU). The stack was designed using a top-down approach, based on a specification of an APU system that is installed on board of vehicles. The stack design is planar, modular and scalable with stamped sheet metal interconnectors. It features thin membrane electrode assemblies (MEAs), such as electrolyte supported cells (ESC) and operates at elevated temperatures around 800 °C. The stack has a low pressure drop in both the anode and the cathode to facilitate a simple system layout. An overview of the technical targets met so far is given. A stack power density of 0.2 kW l -1 has been demonstrated in a fully integrated, thermally self-sustaining APU prototype running with diesel and without an external water supply.

A digital acquisition and elaboration system for nuclear fast pulse detection

NASA Astrophysics Data System (ADS)

Esposito, B.; Riva, M.; Marocco, D.; Kaschuck, Y.

2007-03-01

A new digital acquisition and elaboration system has been developed and assembled in ENEA-Frascati for the direct sampling of fast pulses from nuclear detectors such as scintillators and diamond detectors. The system is capable of performing the digital sampling of the pulses (200 MSamples/s, 14-bit) and the simultaneous (compressed) data transfer for further storage and software elaboration. The design (FPGA-based) is oriented to real-time applications and has been developed in order to allow acquisition with no loss of pulses and data storage for long-time intervals (tens of s at MHz pulse count rates) without the need of large on-board memory. A dedicated pulse analysis software, written in LabVIEWTM, performs the treatment of the acquired pulses, including pulse recognition, pile-up rejection, baseline removal, pulse shape particle separation and pulse height spectra analysis. The acquisition and pre-elaboration programs have been fully integrated with the analysis software.

AVIRIS foreoptics, fiber optics and on-board calibrator

NASA Technical Reports Server (NTRS)

Chrisp, Michael P.; Chrien, Thomas G.; Steimle, L.

1987-01-01

The foreoptics, fiber optic system and calibration source of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) are described. The foreoptics, based on a modified Kennedy scanner, is coupled by optical fibers to the four spectrometers. The optical fibers allow convenient positioning of the spectrometers in the limited space and enable simple compensation of the scanner's thermal defocus (at the -23 C operating temp) by active control of the fiber focal plane position. A challenging requirement for the fiber optic system was the transmission to the spectral range 1.85 to 2.45 microns at .45 numerical aperture. This was solved with custom fluoride glass fibers from Verre Fluore. The onboard calibration source is also coupled to the spectrometers by the fibers and provides two radiometric levels and a reference spectrum to check the spectrometers' alignment. Results of the performance of the assembled subsystems are presented.

Waveguide metatronics: Lumped circuitry based on structural dispersion.

PubMed

Li, Yue; Liberal, Iñigo; Della Giovampaola, Cristian; Engheta, Nader

2016-06-01

Engineering optical nanocircuits by exploiting modularization concepts and methods inherited from electronics may lead to multiple innovations in optical information processing at the nanoscale. We introduce the concept of "waveguide metatronics," an advanced form of optical metatronics that uses structural dispersion in waveguides to obtain the materials and structures required to construct this class of circuitry. Using numerical simulations, we demonstrate that the design of a metatronic circuit can be carried out by using a waveguide filled with materials with positive permittivity. This includes the implementation of all "lumped" circuit elements and their assembly in a single circuit board. In doing so, we extend the concepts of optical metatronics to frequency ranges where there are no natural plasmonic materials available. The proposed methodology could be exploited as a platform to experimentally validate optical metatronic circuits in other frequency regimes, such as microwave frequency setups, and/or to provide a new route to design optical nanocircuitry.

A Simple, Low-Cost Platform for Real-Time Isothermal Nucleic Acid Amplification

PubMed Central

Craw, Pascal; Mackay, Ruth E.; Naveenathayalan, Angel; Hudson, Chris; Branavan, Manoharanehru; Sadiq, S. Tariq; Balachandran, Wamadeva

2015-01-01

Advances in microfluidics and the introduction of isothermal nucleic acid amplification assays have resulted in a range of solutions for nucleic acid amplification tests suited for point of care and field use. However, miniaturisation of instrumentation for such assays has not seen such rapid advances and fluorescence based assays still depend on complex, bulky and expensive optics such as fluorescence microscopes, photomultiplier tubes and sensitive lens assemblies. In this work we demonstrate a robust, low cost platform for isothermal nucleic acid amplification on a microfluidic device. Using easily obtainable materials and commercial off-the-shelf components, we show real time fluorescence detection using a low cost photodiode and operational amplifier without need for lenses. Temperature regulation on the device is achieved using a heater fabricated with standard printed circuit board fabrication methods. These facile construction methods allow fabrications at a cost compatible with widespread deployment to resource poor settings. PMID:26389913

Stretchable electronics based on Ag-PDMS composites

PubMed Central

Larmagnac, Alexandre; Eggenberger, Samuel; Janossy, Hanna; Vörös, Janos

2014-01-01

Patterned structures of flexible, stretchable, electrically conductive materials on soft substrates could lead to novel electronic devices with unique mechanical properties allowing them to bend, fold, stretch or conform to their environment. For the last decade, research on improving the stretchability of circuits on elastomeric substrates has made significant progresses but designing printed circuit assemblies on elastomers remains challenging. Here we present a simple, cost-effective, cleanroom-free process to produce large scale soft electronic hardware where standard surface-mounted electrical components were directly bonded onto all-elastomeric printed circuit boards, or soft PCBs. Ag-PDMS tracks were stencil printed onto a PDMS substrate and soft PCBs were made by bonding the top and bottom layers together and filling punched holes with Ag-PDMS to create vias. Silver epoxy was used to bond commercial electrical components and no mechanical failure was observed after hundreds of stretching cycles. We also demonstrate the fabrication of a stretchable clock generator. PMID:25434843

Characterization of spectrometric photon-counting X-ray detectors at different pitches

NASA Astrophysics Data System (ADS)

Jurdit, M.; Brambilla, A.; Moulin, V.; Ouvrier-Buffet, P.; Radisson, P.; Verger, L.

2017-09-01

There is growing interest in energy-sensitive photon-counting detectors based on high flux X-ray imaging. Their potential applications include medical imaging, non-destructive testing and security. Innovative detectors of this type will need to count individual photons and sort them into selected energy bins, at several million counts per second and per mm2. Cd(Zn)Te detector grade materials with a thickness of 1.5 to 3 mm and pitches from 800 μm down to 200 μm were assembled onto interposer boards. These devices were tested using in-house-developed full-digital fast readout electronics. The 16-channel demonstrators, with 256 energy bins, were experimentally characterized by determining spectral resolution, count rate, and charge sharing, which becomes challenging at low pitch. Charge sharing correction was found to efficiently correct X-ray spectra up to 40 × 106 incident photons.s-1.mm-2.

Sensor assembly method using silicon interposer with trenches for three-dimensional binocular range sensors

NASA Astrophysics Data System (ADS)

Nakajima, Kazuhiro; Yamamoto, Yuji; Arima, Yutaka

2018-04-01

To easily assemble a three-dimensional binocular range sensor, we devised an alignment method for two image sensors using a silicon interposer with trenches. The trenches were formed using deep reactive ion etching (RIE) equipment. We produced a three-dimensional (3D) range sensor using the method and experimentally confirmed that sufficient alignment accuracy was realized. It was confirmed that the alignment accuracy of the two image sensors when using the proposed method is more than twice that of the alignment assembly method on a conventional board. In addition, as a result of evaluating the deterioration of the detection performance caused by the alignment accuracy, it was confirmed that the vertical deviation between the corresponding pixels in the two image sensors is substantially proportional to the decrease in detection performance. Therefore, we confirmed that the proposed method can realize more than twice the detection performance of the conventional method. Through these evaluations, the effectiveness of the 3D binocular range sensor aligned by the silicon interposer with the trenches was confirmed.

Dynamics of self-assembled cytosine nucleobases on graphene

NASA Astrophysics Data System (ADS)

Saikia, Nabanita; Johnson, Floyd; Waters, Kevin; Pandey, Ravindra

2018-05-01

Molecular self-assembly of cytosine (C n ) bases on graphene was investigated using molecular dynamics methods. For free-standing C n bases, simulation conditions (gas versus aqueous) determine the nature of self-assembly; the bases prefer to aggregate in the gas phase and are stabilized by intermolecular H-bonds, while in the aqueous phase, the water molecules disrupt base-base interactions, which facilitate the formation of π-stacked domains. The substrate-induced effects, on the other hand, find the polarity and donor-acceptor sites of the bases to govern the assembly process. For example, in the gas phase, the assembly of C n bases on graphene displays short-range ordered linear arrays stabilized by the intermolecular H-bonds. In the aqueous phase, however, there are two distinct configurations for the C n bases assembly on graphene. For the first case corresponding to low surface coverage, the bases are dispersed on graphene and are isolated. The second configuration archetype is disordered linear arrays assembled with medium and high surface coverage. The simulation results establish the role of H-bonding, vdW π-stacking, and the influence of graphene surface towards the self-assembly. The ability to regulate the assembly into well-defined patterns can aid in the design of self-assembled nanostructures for the next-generation DNA based biosensors and nanoelectronic devices.

Soldering Technology. Proceedings of Annual Seminar (8th) Held on 22-23 February 1984

DTIC Science & Technology

1984-02-01

conducted and test data proves that they can not only be cost effective, but that they also improve product quality. These proceedings are published for your...aoticr piobiem with tK old system. and density per assembly ranges from 10 to 650 Very little or no data was recorded to evaluate the components. In the...soldering. This process, illustrated in on each board. Figure 2. provides engineering with the data 9 Defined Solder Screen - The same defect on needed and

History of the 4th Battalion, 37th Armored Regiment in Operation Desert Shield/Storm. Volume 1

DTIC Science & Technology

1992-04-15

find and unpack the MILVAN with his canvas inside. One of the big issues was our concern over the new model 900 series sabot ammunition. It was...Recommendations 3rd Brigade Change of Command Sand Storms Visit to Rear Assembly Area Huebner Live Fire Training Day-to-Day Business and...the S2. It consisted of model terrain boards of the battalion’s General Defense Plan (GDP) in the FRG, the National Training Center (NTC), and the

Improved Design Process Part of the Ship Producibility Program of the National Shipbuilding Research Program

DTIC Science & Technology

1977-04-01

Exh and Escape Fresh Water Feed Treatment Cargo Oil Tank Cleaning Diesel Generator Piping Piping Material Schedule List of Motors and... tank length frame and stiffener spacing, etc. One yard buys only mill edge plates, and one yard buys only cold flange quality plates. 2-13 C. POST...gage boards, all interconnecting piping and valves, and all mounted on a common foundation, or a pump room assembled on a tank top unit. Use of packages

NASA Conducts 2nd RS-25 Engine Hot Fire of 2018

NASA Image and Video Library

2018-02-01

A 365-second hot fire test on Feb. 1, 2018, at NASA’s Stennis Space Center in Mississippi marks the completion of “green run” testing, or flight certification, for all new RS-25 engine flight controllers slated for Exploration Mission-2, the first Space Launch System mission with astronauts on board. In addition to the flight controller, the Feb. 1 hot fire also marked the third test of a 3D printed pogo accumulator assembly for the RS-25 engine.

Design of a K-Band Transmit Phased Array For Low Earth Orbit Satellite Communications

NASA Technical Reports Server (NTRS)

Watson, Thomas; Miller, Stephen; Kershner, Dennis; Anzic, Godfrey

2000-01-01

The design of a light weight, low cost phased array antenna is presented. Multilayer printed wiring board (PWB) technology is utilized for Radio Frequencies (RF) and DC/Logic manifold distribution. Transmit modules are soldered on one side and patch antenna elements are on the other, allowing the use of automated assembly processes. The 19 GHz antenna has two independently steerable beams, each capable of transferring data at 622 Mbps. A passive, self-contained phase change thermal management system is also presented.

Computer Programs for Prediction of Lightning Induced Voltages in Aircraft Electrical Circuits

DTIC Science & Technology

1975-04-01

8217-Mnnmn " ■*> i ■ : mmmmim*mmemmmMmmmmmam*t*ammi m ■■>■ ■ ,-,.->»^~—~—-. ■ - m^m Test techniques and equipment have been designed for subjecting com...are still on the drawing board, when there is as yet no aircraft on which to run tests . To fulfill this need, a program was initiated by the Air...aluated by full-scale simulated lightning tests of the external assemblies in question. Government specifications for some of these devices or

Space station common module network topology and hardware development

NASA Technical Reports Server (NTRS)

Anderson, P.; Braunagel, L.; Chwirka, S.; Fishman, M.; Freeman, K.; Eason, D.; Landis, D.; Lech, L.; Martin, J.; Mccorkle, J.

1990-01-01

Conceptual space station common module power management and distribution (SSM/PMAD) network layouts and detailed network evaluations were developed. Individual pieces of hardware to be developed for the SSM/PMAD test bed were identified. A technology assessment was developed to identify pieces of equipment requiring development effort. Equipment lists were developed from the previously selected network schematics. Additionally, functional requirements for the network equipment as well as other requirements which affected the suitability of specific items for use on the Space Station Program were identified. Assembly requirements were derived based on the SSM/PMAD developed requirements and on the selected SSM/PMAD network concepts. Basic requirements and simplified design block diagrams are included. DC remote power controllers were successfully integrated into the DC Marshall Space Flight Center breadboard. Two DC remote power controller (RPC) boards experienced mechanical failure of UES 706 stud-mounted diodes during mechanical installation of the boards into the system. These broken diodes caused input to output shorting of the RPC's. The UES 706 diodes were replaced on these RPC's which eliminated the problem. The DC RPC's as existing in the present breadboard configuration do not provide ground fault protection because the RPC was designed to only switch the hot side current. If ground fault protection were to be implemented, it would be necessary to design the system so the RPC switched both the hot and the return sides of power.

Packaging printed circuit boards: A production application of interactive graphics

NASA Technical Reports Server (NTRS)

Perrill, W. A.

1975-01-01

The structure and use of an Interactive Graphics Packaging Program (IGPP), conceived to apply computer graphics to the design of packaging electronic circuits onto printed circuit boards (PCB), were described. The intent was to combine the data storage and manipulative power of the computer with the imaginative, intuitive power of a human designer. The hardware includes a CDC 6400 computer and two CDC 777 terminals with CRT screens, light pens, and keyboards. The program is written in FORTRAN 4 extended with the exception of a few functions coded in COMPASS (assembly language). The IGPP performs four major functions for the designer: (1) data input and display, (2) component placement (automatic or manual), (3) conductor path routing (automatic or manual), and (4) data output. The most complex PCB packaged to date measured 16.5 cm by 19 cm and contained 380 components, two layers of ground planes and four layers of conductors mixed with ground planes.

U.S. Congress Considers Hurricane Research Bills

NASA Astrophysics Data System (ADS)

Von Holle, Kate

2007-07-01

Legislation currently being considered by both the U.S. House and Senate would create a National Hurricane Research Initiative. The legislation was developed in response to a January 2007 U.S. National Science Board report,"Hurricane warning: The critical need for a National Hurricane Research Initiative." Both bills require the hurricane research initiative to set objectives in order to make recommendations to the National Science Board and to assemble U.S. science and engineering expertise through an interagency effort designed to bring together the latest research focusing on infrastructure, forecasting, and mitigating impacts on coastal populations. The bills also require the initiative to set objectives for making grants for hurricane research on a variety of topics, ranging from hurricane dynamics to improving emergency communications networks. Coordination of the interagency effort would fall under the jurisdiction of the White House Office of Science and Technology Policy.

Direct write fabrication of waveguides and interconnects for optical printed wiring boards

NASA Astrophysics Data System (ADS)

Dingeldein, Joseph C.

Current copper based circuit technology is becoming a limiting factor in high speed data transfer applications as processors are improving at a faster rate than are developments to increase on board data transfer. One solution is to utilize optical waveguide technology to overcome these bandwidth and loss restrictions. The use of this technology virtually eliminates the heat and cross-talk loss seen in copper circuitry, while also operating at a higher bandwidth. Transitioning current fabrication techniques from small scale laboratory environments to large scale manufacturing presents significant challenges. Optical-to-electrical connections and out-of-plane coupling are significant hurdles in the advancement of optical interconnects. The main goals of this research are the development of direct write material deposition and patterning tools for the fabrication of waveguide systems on large substrates, and the development of out-of-plane coupler components compatible with standard fiber optic cabling. Combining these elements with standard printed circuit boards allows for the fabrication of fully functional optical-electrical-printed-wiring-boards (OEPWBs). A direct dispense tool was designed, assembled, and characterized for the repeatable dispensing of blanket waveguide layers over a range of thicknesses (25-225 μm), eliminating waste material and affording the ability to utilize large substrates. This tool was used to directly dispense multimode waveguide cores which required no UV definition or development. These cores had circular cross sections and were comparable in optical performance to lithographically fabricated square waveguides. Laser direct writing is a non-contact process that allows for the dynamic UV patterning of waveguide material on large substrates, eliminating the need for high resolution masks. A laser direct write tool was designed, assembled, and characterized for direct write patterning waveguides that were comparable in quality to those produced using standard lithographic practices (0.047 dB/cm loss for laser written waveguides compared to 0.043 dB/cm for lithographic waveguides). Straight waveguides, and waveguide turns were patterned at multimode and single mode sizes, and the process was characterized and documented. Support structures such as angled reflectors and vertical posts were produced, showing the versatility of the laser direct write tool. Commercially available components were implanted into the optical layer for out-of-plane routing of the optical signals. These devices featured spherical lenses on the input and output sides of a total internal reflection (TIR) mirror, as well as alignment pins compatible with standard MT design. Fully functional OEPWBs were fabricated featuring input and output out-of-plane optical signal routing with total optical losses not exceeding 10 dB. These prototypes survived thermal cycling (-40°C to 85°C) and humidity exposure (95±4% humidity), showing minimal degradation in optical performance. Operational failure occurred after environmental aging life testing at 110°C for 216 hours.

Use of Commercial FPGA-Based Evaluation Boards for Single-Event Testing of DDR2 and DDR3 SDRAMs

NASA Technical Reports Server (NTRS)

Ladbury, R. L.; Berg, M. D.; Wilcox, E. P.; LaBel, K. A.; Kim, H. S.; Phan, A. M.; Seidleck, C. M.

2013-01-01

We investigate the use of commercial FPGA based evaluation boards for radiation testing DDR2 and DDR3 SDRAMs. We evaluate the resulting data quality and the tradeoffs involved in the use of these boards.

Risk Mitigation Testing with the BepiColombo MPO SADA

NASA Astrophysics Data System (ADS)

Zemann, J.; Heinrich, B.; Skulicz, A.; Madsen, M.; Weisenstein, W.; Modugno, F.; Althaus, F.; Panhofer, T.; Osterseher, G.

2013-09-01

A Solar Array (SA) Drive Assembly (SADA) for the BepiColombo mission is being developed and qualified at RUAG Space Zürich (RSSZ). The system is consisting of the Solar Array Drive Mechanism (SADM) and the Solar Array Drive Electronics (SADE) which is subcontracted to RUAG Space Austria (RSA).This paper deals with the risk mitigation activities and the lesson learnt from this development. In specific following topics substantiated by bread board (BB) test results will be addressed in detail:Slipring Bread Board Test: Verification of lifetime and electrical performance of carbon brush technology Potentiometer BB Tests: Focus on lifetime verification (> 650000 revolution) and accuracy requirement SADM EM BB Test: Subcomponent (front-bearing and gearbox) characterization; complete test campaign equivalent to QM test.EM SADM/ SADE Combined Test: Verification of combined performance (accuracy, torque margin) and micro-vibration testing of SADA systemSADE Bread Board Test: Parameter optimization; Test campaign equivalent to QM testThe main improvements identified in frame of BB testing and already implemented in the SADM EM/QM and SADE EQM are:• Improved preload device for gearbox• Improved motor ball-bearing assembly• Position sensor improvements• Calibration process for potentiometer• SADE motor controller optimization toachieve required running smoothness• Overall improvement of test equipment.

The self-assembled behavior of DNA bases on the interface.

PubMed

Liu, Lei; Xia, Dan; Klausen, Lasse H; Dong, Mingdong

2014-01-27

A successful example of self-assembly in a biological system is that DNA can be an excellent agent to self-assemble into desirable two and three-dimensional nanostructures in a well-ordered manner by specific hydrogen bonding interactions between the DNA bases. The self-assembly of DNA bases have played a significant role in constructing the hierarchical nanostructures. In this review article we will introduce the study of nucleic acid base self-assembly by scanning tunneling microscopy (STM) at vacuum and ambient condition (the liquid/solid interface), respectively. From the ideal condition to a more realistic environment, the self-assembled behaviors of DNA bases are introduced. In a vacuum system, the energetic advantages will dominate the assembly formation of DNA bases, while at ambient condition, more factors such as conformational freedom and the biochemical environment will be considered. Therefore, the assemblies of DNA bases at ambient condition are different from the ones obtained under vacuum. We present the ordered nanostructures formed by DNA bases at both vacuum and ambient condition. To construct and tailor the nanostructure through the interaction between DNA bases, it is important to understand the assembly behavior and features of DNA bases and their derivatives at ambient condition. The utilization of STM offers the advantage of investigating DNA base self-assembly with sub-molecular level resolution at the surface.

The Self-Assembled Behavior of DNA Bases on the Interface

PubMed Central

Liu, Lei; Xia, Dan; Klausen, Lasse H.; Dong, Mingdong

2014-01-01

A successful example of self-assembly in a biological system is that DNA can be an excellent agent to self-assemble into desirable two and three-dimensional nanostructures in a well-ordered manner by specific hydrogen bonding interactions between the DNA bases. The self-assembly of DNA bases have played a significant role in constructing the hierarchical nanostructures. In this review article we will introduce the study of nucleic acid base self-assembly by scanning tunneling microscopy (STM) at vacuum and ambient condition (the liquid/solid interface), respectively. From the ideal condition to a more realistic environment, the self-assembled behaviors of DNA bases are introduced. In a vacuum system, the energetic advantages will dominate the assembly formation of DNA bases, while at ambient condition, more factors such as conformational freedom and the biochemical environment will be considered. Therefore, the assemblies of DNA bases at ambient condition are different from the ones obtained under vacuum. We present the ordered nanostructures formed by DNA bases at both vacuum and ambient condition. To construct and tailor the nanostructure through the interaction between DNA bases, it is important to understand the assembly behavior and features of DNA bases and their derivatives at ambient condition. The utilization of STM offers the advantage of investigating DNA base self-assembly with sub-molecular level resolution at the surface. PMID:24473140

Handling Qualities Flight Testing of the Stratospheric Observatory for Infrared Astronomy (SOFIA)

NASA Technical Reports Server (NTRS)

Glaser, Scott T.; Strovers, Brian K.

2011-01-01

Airborne infrared astronomy has a long successful history, albeit relatively unknown outside of the astronomy community. A major problem with ground based infrared astronomy is the absorption and scatter of infrared energy by water in the atmosphere. Observing the universe from above 40,000 ft puts the observation platform above 99% of the water vapor in the atmosphere, thereby addressing this problem at a fraction of the cost of space based systems. The Stratospheric Observatory For Infrared Astronomy (SOFIA) aircraft is the most ambitious foray into the field of airborne infrared astronomy in history. Using a 747SP (The Boeing Company, Chicago, Illinois) aircraft modified with a 2.5m telescope located in the aft section of the fuselage, the SOFIA endeavors to provide views of the universe never before possible and at a fraction of the cost of space based systems. The modification to the airplane includes moveable doors and aperture that expose the telescope assembly. The telescope assembly is aimed and stabilized using a multitude of on board systems. This modification has the potential to cause aerodynamic anomalies that could induce undesired forces either at the cavity itself or indirectly due to interference with the empennage, both of which could cause handling qualities issues. As a result, an extensive analysis and flight test program was conducted from December 2009 through March 2011. Several methods, including a Lower Order Equivalent Systems analysis and pilot assessment, were used to ascertain the effects of the modification. The SOFIA modification was found to cause no adverse handling qualities effects and the aircraft was cleared for operational use. This paper discusses the history and modification to the aircraft, development of test procedures and analysis, results of testing and analysis, lessons learned for future projects and justification for operational certification.

Outsourcing the Superintendency: Contextual Changes to the Urban School Superintendent.

ERIC Educational Resources Information Center

Sanders, Eugene T. W.; And Others

1998-01-01

Analyzes an urban Ohio school board's decision regarding potential employment of a business firm instead of a traditional superintendent, highlighting the board's selection process and the nature of board/community interactions. The study used an interview guide format with five board members. The board chose not to hire a Minnesota-based firm for…

12 CFR 217.205 - VaR-based measure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... requirements. The Board-regulated institution must update data sets at least monthly or more frequently as... year. Data used to determine the VaR-based measure must be relevant to the Board-regulated institution.... A Board-regulated institution using this option must update its data more frequently than monthly...

AstroBus On-Board Software

NASA Astrophysics Data System (ADS)

Biscarros, D.; Cantenot, C.; Séronie-Vivien, J.; Schmidt, G.

AstroBus on-board software is a customisable software for ERC32 based avionics implementing standard ESA Packet Utilization Standard functions. Its architecture based on generic design templates and relying on a library providing standard PUS TC, TM and event services enhances its reusability on various programs. Finally, AstroBus on-board software development and validation environment is based on last generation tools providing an optimised customisation environment.

Optical links in handheld multimedia devices

NASA Astrophysics Data System (ADS)

van Geffen, S.; Duis, J.; Miller, R.

2008-04-01

Ever emerging applications in handheld multimedia devices such as mobile phones, laptop computers, portable video games and digital cameras requiring increased screen resolutions are driving higher aggregate bitrates between host processor and display(s) enabling services such as mobile video conferencing, video on demand and TV broadcasting. Larger displays and smaller phones require complex mechanical 3D hinge configurations striving to combine maximum functionality with compact building volumes. Conventional galvanic interconnections such as Micro-Coax and FPC carrying parallel digital data between host processor and display module may produce Electromagnetic Interference (EMI) and bandwidth limitations caused by small cable size and tight cable bends. To reduce the number of signals through a hinge, the mobile phone industry, organized in the MIPI (Mobile Industry Processor Interface) alliance, is currently defining an electrical interface transmitting serialized digital data at speeds >1Gbps. This interface allows for electrical or optical interconnects. Above 1Gbps optical links may offer a cost effective alternative because of their flexibility, increased bandwidth and immunity to EMI. This paper describes the development of optical links for handheld communication devices. A cable assembly based on a special Plastic Optical Fiber (POF) selected for its mechanical durability is terminated with a small form factor molded lens assembly which interfaces between an 850nm VCSEL transmitter and a receiving device on the printed circuit board of the display module. A statistical approach based on a Lean Design For Six Sigma (LDFSS) roadmap for new product development tries to find an optimum link definition which will be robust and low cost meeting the power consumption requirements appropriate for battery operated systems.

Adult Competency Education Kit. Basic Skills in Speaking, Math, and Reading for Employment. Part P: ACE Competency Based Job Descriptions: #77--Secretary; #78--Keypunch Operator; Assembly Worker Core Job Description; #82--Electronics Assembler; #83--Printed Circuit Assembler; #84--Micro Electronics Assembler; #85--Chassis Assembler; #87--Machinist Apprentice.

ERIC Educational Resources Information Center

San Mateo County Office of Education, Redwood City, CA. Career Preparation Centers.

This thirteenth of fifteen sets of Adult Competency Education (ACE) Competency Based Job Descriptions in the ACE kit contains job descriptions for Secretary, Keypunch Operator, Electronics Assembler, Printed Circuit Assembler, Micro Electronincs Assembler, Chassis Assembler, and Machinist Apprentice. Each begins with a fact sheet that includes…

Analysis of large space structures assembly: Man/machine assembly analysis

NASA Technical Reports Server (NTRS)

1983-01-01

Procedures for analyzing large space structures assembly via three primary modes: manual, remote and automated are outlined. Data bases on each of the assembly modes and a general data base on the shuttle capabilities to support structures assembly are presented. Task element times and structure assembly component costs are given to provide a basis for determining the comparative economics of assembly alternatives. The lessons learned from simulations of space structures assembly are detailed.

Test-bench system for a borehole azimuthal acoustic reflection imaging logging tool

NASA Astrophysics Data System (ADS)

Liu, Xianping; Ju, Xiaodong; Qiao, Wenxiao; Lu, Junqiang; Men, Baiyong; Liu, Dong

2016-06-01

The borehole azimuthal acoustic reflection imaging logging tool (BAAR) is a new generation of imaging logging tool, which is able to investigate stratums in a relatively larger range of space around the borehole. The BAAR is designed based on the idea of modularization with a very complex structure, so it has become urgent for us to develop a dedicated test-bench system to debug each module of the BAAR. With the help of a test-bench system introduced in this paper, test and calibration of BAAR can be easily achieved. The test-bench system is designed based on the client/server model. The hardware system mainly consists of a host computer, an embedded controlling board, a bus interface board, a data acquisition board and a telemetry communication board. The host computer serves as the human machine interface and processes the uploaded data. The software running on the host computer is designed based on VC++. The embedded controlling board uses Advanced Reduced Instruction Set Machines 7 (ARM7) as the micro controller and communicates with the host computer via Ethernet. The software for the embedded controlling board is developed based on the operating system uClinux. The bus interface board, data acquisition board and telemetry communication board are designed based on a field programmable gate array (FPGA) and provide test interfaces for the logging tool. To examine the feasibility of the test-bench system, it was set up to perform a test on BAAR. By analyzing the test results, an unqualified channel of the electronic receiving cabin was discovered. It is suggested that the test-bench system can be used to quickly determine the working condition of sub modules of BAAR and it is of great significance in improving production efficiency and accelerating industrial production of the logging tool.

Development of a miniature multiple reference optical coherence tomography imaging device

NASA Astrophysics Data System (ADS)

McNamara, Paul M.; O'Riordan, Colm; Collins, Seán.; O'Brien, Peter; Wilson, Carol; Hogan, Josh; Leahy, Martin J.

2016-03-01

Multiple reference optical coherence tomography (MR-OCT) is a new technology ideally suited to low-cost, compact OCT imaging. This modality is an extension of time-domain OCT with the addition of a partial mirror in front of the reference mirror. This enables extended, simultaneous depth scanning with the relatively short sweep of a miniature voice coil motor on which the scanning mirror is mounted. Applications of this technology include biometric security, ophthalmology, personal health monitoring and non-destructive testing. This work details early-stage development of the first iteration of a miniature MR-OCT device. This device utilizes a fiber-coupled input from an off-board superluminescent diode (SLD). Typical dimensions of the module are 40 × 57 mm, but future designs are expected to be more compact. Off-the-shelf miniature optical components, voice coil motors and photodetectors are used, with the complexity of design depending on specific applications. The photonic module can be configured as either polarized or non-polarized and can include balanced detection. The photodetectors are directly connected to a printed circuit board under the module containing a transimpedance amplifier with complimentary outputs. The results shown in this work are from the non-polarized device. Assembly of the photonic modules requires extensive planning. In choosing the optical components, Zemax simulations are performed to model the beam characteristics. The physical layout is modeled using Solidworks and each component is placed and aligned via a well-designed alignment procedure involving an active-alignment pick-and-place assembly system.

Control over self-assembly of diblock copolymers on hexagonal and square templates for high area density circuit boards.

PubMed

Feng, Jie; Cavicchi, Kevin A; Heinz, Hendrik

2011-12-27

Self-assembled diblock copolymer melts on patterned substrates can induce a smaller characteristic domain spacing compared to predefined lithographic patterns and enable the manufacture of circuit boards with a high area density of computing and storage units. Monte Carlo simulation using coarse-grain models of polystyrene-b-polydimethylsiloxane shows that the generation of high-density hexagonal and square patterns is controlled by the ratio N(D) of the surface area per post and the surface area per spherical domain of neat block copolymer. N(D) represents the preferred number of block copolymer domains per post. Selected integer numbers support the formation of ordered structures on hexagonal (1, 3, 4, 7, 9) and square (1, 2, 5, 7) templates. On square templates, only smaller numbers of block copolymer domains per post support the formation of ordered arrays with significant stabilization energies relative to hexagonal morphology. Deviation from suitable integer numbers N(D) increases the likelihood of transitional morphologies between square and hexagonal. Upon increasing the spacing of posts on the substrate, square arrays, nested square arrays, and disordered hexagonal morphologies with multiple coordination numbers were identified, accompanied by a decrease in stabilization energy. Control over the main design parameter N(D) may allow an up to 7-fold increase in density of spherical block copolymer domains per surface area in comparison to the density of square posts and provide access to a wide range of high-density nanostructures to pattern electronic devices.

Flight motor set 36OH005 (STS-28R). Volume 5: (Nozzle component)

NASA Technical Reports Server (NTRS)

Smith, Dan M., Jr.

1990-01-01

A review of the performance and post flight condition of the STS-28 redesigned solid rocket motor (RSRM) nozzles is presented in this document. Applicable discrepancy reports (DR's) and process departures (PD's) are presented in section 5.0. The nozzle component program team (NCPT) performance evaluation and the redesign program review board (RPRB) assessment is included in section 6.0. The STS-28 nozzle assemblies were flown on the RSRM fifth flight (Space Shuttle Columbia). The nozzles were a partially submerged convergent/divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: (1) RSRM forward exit cone with snubber assembly; (2) RSRM fixed housing; (3) structural backup outer boot ring (OBR); (4) RSRM cowl ring; (5) RSRM nose inlet assembly; (6) RSRM throat assembly; (7) RSRM forward nose and aft inlet ring; (8) RSRM aft exit cone assembly with linear-shaped charge (LSC); (9) RTV backfill in joints 1, 3, and 4; (10) use of EA913 NA adhesive in place of EA913; (11) redesigned nozzle plug; and (12) carbon cloth phenolic (CCP) with 750 ppm sodium content. The RSRM fifth flight test objectives are as follows: (1) verify that flexible bearing seals operate within the specified temperature range; (2) verify that flexible bearing maintained a positive gas seal between its internal components; (3) inspect flexible bearing for damage due to water impact; (4) verify performance of the nozzle liner; (5) verify that nozzle parts are reusable; (6) verify through flight demonstration and a postflight inspection that the flexible bearing is reusable; (7) verify by inspection the remaining nozzle ablative thicknesses; and (8) verify the nozzle performance margins of safety.

Research to Assembly Scheme for Satellite Deck Based on Robot Flexibility Control Principle

NASA Astrophysics Data System (ADS)

Guo, Tao; Hu, Ruiqin; Xiao, Zhengyi; Zhao, Jingjing; Fang, Zhikai

2018-03-01

Deck assembly is critical quality control point in final satellite assembly process, and cable extrusion and structure collision problems in assembly process will affect development quality and progress of satellite directly. Aimed at problems existing in deck assembly process, assembly project scheme for satellite deck based on robot flexibility control principle is proposed in this paper. Scheme is introduced firstly; secondly, key technologies on end force perception and flexible docking control in the scheme are studied; then, implementation process of assembly scheme for satellite deck is described in detail; finally, actual application case of assembly scheme is given. Result shows that compared with traditional assembly scheme, assembly scheme for satellite deck based on robot flexibility control principle has obvious advantages in work efficiency, reliability and universality aspects etc.

Optical connections on flexible substrates

NASA Astrophysics Data System (ADS)

Bosman, Erwin; Geerinck, Peter; Christiaens, Wim; Van Steenberge, Geert; Vanfleteren, Jan; Van Daele, Peter

2006-04-01

Optical interconnections integrated on a flexible substrate combine the advantages of optical data transmissions (high bandwidth, no electromagnetic disturbance and low power consumption) and those of flexible substrates (compact, ease of assembly...). Especially the flexible character of the substrates can significantly lower the assembly cost and leads to more compact modules. Especially in automotive-, avionic-, biomedical and sensing applications there is a great potential for these flexible optical interconnections because of the increasing data-rates, increasing use of optical sensors and requirement for smaller size and weight. The research concentrates on the integration of commercially available polymer optical layers (Truemode Backplane TM Polymer, Ormocer®) on a flexible Polyimide film, the fabrication of waveguides and out-of plane deflecting 45° mirrors, the characterization of the optical losses due to the bending of the substrate, and the fabrication of a proof-of-principal demonstrator. The resulting optical structures should be compatible with the standard fabrication of flexible printed circuit boards.

Driver-receiver combined optical transceiver modules for bidirectional optical interconnection

NASA Astrophysics Data System (ADS)

Park, Hyo-Hoon; Kang, Sae-Kyoung; Kim, Do-Won; Nga, Nguyen T. H.; Hwang, Sung-Hwan; Lee, Tae-Woo

2008-02-01

We review a bidirectional optical link scheme for memory-interface applications. A driver-receiver combined optical transceiver (TRx) modules was demonstrated on an optical printed-circuit board (OPCB) platform. To select the bidirectional electric input/output signals, a driver-receiver combined TRx IC with a switching function was designed in 0.18-μm CMOS technology. The TRx IC was integrated with VCSEL/PD chips for optical link in the TRx module. The optical TRx module was assembled on a fiber-embedded OPCB, employing a 90°-bent fiber connector for 90° deflection of light beams between the TRx module and the OPCB. The TRx module and the 90° connector were passively assembled on the OPCB, using ferrule-type guide pins/ holes. Employing these constituent components, the bidirectional optical link between a pair of TRx modules has been successfully demonstrated up to 1.25 Gb/s on the OPCB.

Hierarchical planning for a surface mounting machine placement.

PubMed

Zeng, You-jiao; Ma, Deng-ze; Jin, Ye; Yan, Jun-qi

2004-11-01

For a surface mounting machine (SMM) in printed circuit board (PCB) assembly line, there are four problems, e.g. CAD data conversion, nozzle selection, feeder assignment and placement sequence determination. A hierarchical planning for them to maximize the throughput rate of an SMM is presented here. To minimize set-up time, a CAD data conversion system was first applied that could automatically generate the data for machine placement from CAD design data files. Then an effective nozzle selection approach implemented to minimize the time of nozzle changing. And then, to minimize picking time, an algorithm for feeder assignment was used to make picking multiple components simultaneously as much as possible. Finally, in order to shorten pick-and-place time, a heuristic algorithm was used to determine optimal component placement sequence according to the decided feeder positions. Experiments were conducted on a four head SMM. The experimental results were used to analyse the assembly line performance.

Surface profile measurement by using the integrated Linnik WLSI and confocal microscope system

NASA Astrophysics Data System (ADS)

Wang, Wei-Chung; Shen, Ming-Hsing; Hwang, Chi-Hung; Yu, Yun-Ting; Wang, Tzu-Fong

2017-06-01

The white-light scanning interferometer (WLSI) and confocal microscope (CM) are the two major optical inspection systems for measuring three-dimensional (3D) surface profile (SP) of micro specimens. Nevertheless, in practical applications, WLSI is more suitable for measuring smooth and low-slope surfaces. On the other hand, CM is more suitable for measuring uneven-reflective and low-reflective surfaces. As for aspect of surface profiles to be measured, the characteristics of WLSI and CM are also different. WLSI is generally used in semiconductor industry while CM is more popular in printed circuit board industry. In this paper, a self-assembled multi-function optical system was integrated to perform Linnik white-light scanning interferometer (Linnik WLSI) and CM. A connecting part composed of tubes, lenses and interferometer was used to conjunct finite and infinite optical systems for Linnik WLSI and CM in the self-assembled optical system. By adopting the flexibility of tubes and lenses, switching to perform two different optical measurements can be easily achieved. Furthermore, based on the shape from focus method with energy of Laplacian filter, the CM was developed to enhance the on focal information of each pixel so that the CM can provide all-in-focus image for performing the 3D SP measurement and analysis simultaneously. As for Linnik WLSI, eleven-step phase shifting algorithm was used to analyze vertical scanning signals and determine the 3D SP.

Failure detection and recovery in the assembly/contingency subsystem

NASA Technical Reports Server (NTRS)

Gantenbein, Rex E.

1993-01-01

The Assembly/Contingency Subsystem (ACS) is the primary communications link on board the Space Station. Any failure in a component of this system or in the external devices through which it communicates with ground-based systems will isolate the Station. The ACS software design includes a failure management capability (ACFM) that provides protocols for failure detection, isolation, and recovery (FDIR). The the ACFM design requirements as outlined in the current ACS software requirements specification document are reviewed. The activities carried out in this review include: (1) an informal, but thorough, end-to-end failure mode and effects analysis of the proposed software architecture for the ACFM; and (2) a prototype of the ACFM software, implemented as a C program under the UNIX operating system. The purpose of this review is to evaluate the FDIR protocols specified in the ACS design and the specifications themselves in light of their use in implementing the ACFM. The basis of failure detection in the ACFM is the loss of signal between the ground and the Station, which (under the appropriate circumstances) will initiate recovery to restore communications. This recovery involves the reconfiguration of the ACS to either a backup set of components or to a degraded communications mode. The initiation of recovery depends largely on the criticality of the failure mode, which is defined by tables in the ACFM and can be modified to provide a measure of flexibility in recovery procedures.

Residual Stress Analysis in Welded Component.

NASA Astrophysics Data System (ADS)

Rouhi, Shahab; Yoshida, Sanichiro; Miura, Fumiya; Sasaki, Tomohiro

Due to local heating, thermal stresses occur during welding; and residual stress and distortion result remain welding. Welding distortion has negative effects on the accuracy of assembly, exterior appearance, and various strengths of the welded structures. Up to date, a lot of experiments and numerical analysis have been developed to assess residual stress. However, quantitative estimation of residual stress based on experiment may involve massive uncertainties and complexity of the measurement process. To comprehensively understand this phenomena, it is necessary to do further researches by means of both experiment and numerical simulation. In this research, we conduct Finite Element Analysis (FEA) for a simple butt-welded metal plate specimen. Thermal input and resultant expansion are modeled with a thermal expansion FEA module and the resultant constitutive response of the material is modeled with a continuous mechanic FEA module. The residual stress is modeled based on permanent deformation occurring during the heating phase of the material. Experiments have also been carried out to compare with the FEA results. Numerical and experimental results show qualitative agreement. The present work was supported by the Louisiana Board of Regents (LEQSF(2016-17)-RD-C-13).

Ionic polymer-metal composite enabled robotic manta ray

NASA Astrophysics Data System (ADS)

Chen, Zheng; Um, Tae I.; Bart-Smith, Hilary

2011-04-01

The manta ray, Manta birostris, demonstrates excellent swimming capabilities; generating highly efficient thrust via flapping of dorsally flattened pectoral fins. In this paper, we present an underwater robot that mimics the swimming behavior of the manta ray. An assembly-based fabrication method is developed to create the artificial pectoral fins, which are capable of generating oscillatory with a large twisting angle between leading and trailing edges. Ionic polymer-metal composite (IPMC) actuators are used as artificial muscles in the fin. Each fin consists of four IPMC beams bonded with a compliant poly(dimethylsiloxane) (PDMS) membrane. By controlling each individual IPMC strips, we are able to generate complex flapping motions. The fin is characterized in terms of tip deflection, tip blocking force, twist angle, and power consumption. Based on the characteristics of the artificial pectoral fin, a small size and free-swimming robotic manta ray is developed. The robot consists of two artificial pectoral fins, a rigid body, and an on-board control unit with a lithium ion rechargeable battery. Experimental results show that the robot swam at a speed of up to 0.055 body length per second (BL/sec).

Technical Review Board Chairperson Guidelines for Conducting Technical Review Boards for Rocket Testing

DTIC Science & Technology

2011-08-17

to create a guide for technical review board chairperson conducting technical review boards for rocket testing performed by the Air Force Research ...BOARDS FOR ROCKET TESTING   TABLE OF CONTENTS List of Acronyms 1 Abstract 2 Chapter 1. Introduction 3 Introduction and Research Question 3...boards for rocket testing performed by the Air Force Research Laboratory’s Space Missile Propulsion Division located at Edwards Air Force Base in

Design of the Wind Tunnel Model Communication Controller Board. Degree awarded by Christopher Newport Univ. on Dec. 1998

NASA Technical Reports Server (NTRS)

Wilson, William C.

1999-01-01

The NASA Langley Research Center's Wind Tunnel Reinvestment project plans to shrink the existing data acquisition electronics to fit inside a wind tunnel model. Space limitations within a model necessitate a distributed system of Application Specific Integrated Circuits (ASICs) rather than a centralized system based on PC boards. This thesis will focus on the design of the prototype of the communication Controller board. A portion of the communication Controller board is to be used as the basis of an ASIC design. The communication Controller board will communicate between the internal model modules and the external data acquisition computer. This board is based around an Field Programmable Gate Array (FPGA), to allow for reconfigurability. In addition to the FPGA, this board contains buffer Random Access Memory (RAM), configuration memory (EEPROM), drivers for the communications ports, and passive components.

A generic FPGA-based detector readout and real-time image processing board

NASA Astrophysics Data System (ADS)

Sarpotdar, Mayuresh; Mathew, Joice; Safonova, Margarita; Murthy, Jayant

2016-07-01

For space-based astronomical observations, it is important to have a mechanism to capture the digital output from the standard detector for further on-board analysis and storage. We have developed a generic (application- wise) field-programmable gate array (FPGA) board to interface with an image sensor, a method to generate the clocks required to read the image data from the sensor, and a real-time image processor system (on-chip) which can be used for various image processing tasks. The FPGA board is applied as the image processor board in the Lunar Ultraviolet Cosmic Imager (LUCI) and a star sensor (StarSense) - instruments developed by our group. In this paper, we discuss the various design considerations for this board and its applications in the future balloon and possible space flights.

Development of testing and training simulator for CEDMCS in KSNP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nam, C. H.; Park, C. Y.; Nam, J. I.

2006-07-01

This paper presents a newly developed testing and training simulator (TTS) for automatically diagnosing and tuning the Control Element Drive Mechanism Control System (CEDMCS). TTS includes a new automatic, diagnostic, method for logic control cards and a new tuning method for phase synchronous pulse cards. In Korea Standard Nuclear Power Plants (KSNP). reactor trips occasionally occur due to a damaged logic control card in CEDMCS. However, there is no pre-diagnostic tester available to detect a damaged card in CEDMCS before it causes a reactor trip. Even after the reactor trip occurs, it is difficult to find the damaged card. Tomore » find the damaged card. ICT is usually used. ICT is an automated, computer-controlled testing system with measurement capabilities for testing active and passive components, or clusters of components, on printed circuit boards (PCB) and/or assemblies. However, ICT cannot detect a time dependent fault correctly and requires removal of the waterproof mating to perform the test. Therefore, the additional procedure of re-coating the PCB card is required after the test. TTS for CEDMCS is designed based on real plant conditions, both electrically and mechanically. Therefore, the operator can operate the Control Element Drive Mechanism (CEDM), which is mounted on the closure head of the reactor vessel (RV) using the soft control panel in ITS, which duplicates the Main Control Board (MCB) in the Main Control Room (MCR). However, during the generation of electric power in a nuclear power plant, it is difficult to operate the CEDM so a CEDM and Control Element Assembly (CEA) mock-up facility was developed to simulate a real plant CEDM. ITS was used for diagnosing and tuning control logic cards in CEDMCS in the Ulchin Nuclear Power Plant No. 4 during the plant overhaul period. It exhibited good performance in detecting the damaged cards and tuning the phase synchronous pulse cards. In addition, TTS was useful in training the CEDMCS operator by supplying detail signal information from the logic cards. (authors)« less

Artificial dexterous hand

NASA Technical Reports Server (NTRS)

Lee, Sukhan (Inventor)

1990-01-01

An artificial dexterous hand is provided for grasping and manipulating objects. The hand includes left and right thumbs that are operatively connected to an engagement assembly which causes movement of the left and right thumbs. The left thumb has a left thumb base and is movable about three separate first left thumb axes which run through the left thumb base. Correspondingly, the right thumb has a right thumb base and is movable about three separate first right thumb axes which run through the right thumb base. The engagement assembly has a gear assembly which is operatively connected to a motor assembly. Upon actuation by the motor assembly, the gear assembly causes movement of the left and right thumbs about the first left thumb axes and first right thumb axes respectively. The hand can also have a center finger which is operatively connected to the engagement assembly and which is interposed between the left and right thumbs. The finger has a finger base and is movable about two separate first finger axes running through the finger base. Therefore, upon actuation by the motor assembly, the gear assembly will also cause movement of the finger about the first finger axes.

Firebrand Production from Building Components Fitted with Siding Treatments

PubMed Central

Suzuki, Sayaka; Manzello, Samuel L.

2016-01-01

Firebrand production from real-scale building components under well-controlled laboratory conditions was investigated. Re-entrant corner assemblies were ignited and during the combustion process, firebrands were collected to determine the size/mass distribution generated from such real-scale building components under varying wind speed. In prior work, a unique ignition methodology was developed to generate firebrands from re-entrant corner assemblies constructed of wood studs and oriented strand board (OSB). In this study, this ignition methodology was applied to re-entrant corners constructed from wood studs/OSB but fitted with actual siding treatments (tar paper and cedar siding) to determine the influence of siding treatments on firebrand generation from wall assemblies. Firebrands were collected with pans filled with water, and then the size and mass of firebrands were measured after drying. The size and mass distributions of firebrands collected in this study were compared with the data from prior component tests as well as the limited studies available in the literature on this topic. Some firebrands were found to be lighter for a given projected area than others, likely produced from cedar siding or tar paper. The effects of applied siding treatments on firebrand production are discussed in detail. PMID:27114643

Firebrand Production from Building Components Fitted with Siding Treatments.

PubMed

Suzuki, Sayaka; Manzello, Samuel L

2016-02-01

Firebrand production from real-scale building components under well-controlled laboratory conditions was investigated. Re-entrant corner assemblies were ignited and during the combustion process, firebrands were collected to determine the size/mass distribution generated from such real-scale building components under varying wind speed. In prior work, a unique ignition methodology was developed to generate firebrands from re-entrant corner assemblies constructed of wood studs and oriented strand board (OSB). In this study, this ignition methodology was applied to re-entrant corners constructed from wood studs/OSB but fitted with actual siding treatments (tar paper and cedar siding) to determine the influence of siding treatments on firebrand generation from wall assemblies. Firebrands were collected with pans filled with water, and then the size and mass of firebrands were measured after drying. The size and mass distributions of firebrands collected in this study were compared with the data from prior component tests as well as the limited studies available in the literature on this topic. Some firebrands were found to be lighter for a given projected area than others, likely produced from cedar siding or tar paper. The effects of applied siding treatments on firebrand production are discussed in detail.

Body of Knowledge (BOK) for Leadless Quad Flat No-Lead/bottom Termination Components (QFN/BTC) Package Trends and Reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza

2014-01-01

Bottom terminated components and quad flat no-lead (BTC/QFN) packages have been extensively used by commercial industry for more than a decade. Cost and performance advantages and the closeness of the packages to the boards make them especially unique for radio frequency (RF) applications. A number of high-reliability parts are now available in this style of package configuration. This report presents a summary of literature surveyed and provides a body of knowledge (BOK) gathered on the status of BTC/QFN and their advanced versions of multi-row QFN (MRQFN) packaging technologies. The report provides a comprehensive review of packaging trends and specifications on design, assembly, and reliability. Emphasis is placed on assembly reliability and associated key design and process parameters because they show lower life than standard leaded package assembly under thermal cycling exposures. Inspection of hidden solder joints for assuring quality is challenging and is similar to ball grid arrays (BGAs). Understanding the key BTC/QFN technology trends, applications, processing parameters, workmanship defects, and reliability behavior is important when judicially selecting and narrowing the follow-on packages for evaluation and testing, as well as for the low risk insertion in high-reliability applications.

Self-Assemblies of novel molecules, VECAR

NASA Astrophysics Data System (ADS)

Shrestha, Bijay; Kim, Hye-Young; Lee, Soojin; Novak, Brian; Moldovan, Dorel

2015-03-01

VECAR is a newly synthesized molecule, which is an amphiphilic antioxidant molecule that consists of two molecular groups, vitamin-E and Carnosine, linked by a hydrocarbon chain. The hydrocarbon chain is hydrophobic and both vitamin-E and Carnosine ends are hydrophilic. In the synthesis process, the length of the hydrophobic chain of VECAR molecules can vary from the shortest (n =0) to the longest (n =18), where n indicates the number of carbon atoms in the chain. We conducted MD simulation studies of self-assembly of VECAR molecules in water using GROMACS on LONI HPC resources. Our study shows that there is a strong correlation between the shape and atomistic structure of the self-assembled nano-structures (SANs) and the chain-length (n) of VECAR molecules. We will report the results of data analyses including the atomistic structure of each SANs and the dynamic and energetic mechanisms of their formation as function of time. In summary, both VECAR molecules of chain-length n =18 and 9 form worm-like micelles, which may be used as a drug delivery system. This research is supported by the Louisiana Board of Regents-RCS Grant (LEQSF(2012-15)-RD-A-19).

Body of Knowledge (BOK) for Leadless Quad Flat No-Lead/Bottom Termination Components (QFN/BTC) Package Trends and Reliability

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza

2014-01-01

Bottom terminated components and quad flat no-lead (BTC/QFN) packages have been extensively used by commercial industry for more than a decade. Cost and performance advantages and the closeness of the packages to the boards make them especially unique for radio frequency (RF) applications. A number of high-reliability parts are now available in this style of package configuration. This report presents a summary of literature surveyed and provides a body of knowledge (BOK) gathered on the status of BTC/QFN and their advanced versions of multi-row QFN (MRQFN) packaging technologies. The report provides a comprehensive review of packaging trends and specifications on design, assembly, and reliability. Emphasis is placed on assembly reliability and associated key design and process parameters because they show lower life than standard leaded package assembly under thermal cycling exposures. Inspection of hidden solder joints for assuring quality is challenging and is similar to ball grid arrays (BGAs). Understanding the key BTC/QFN technology trends, applications, processing parameters, workmanship defects, and reliability behavior is important when judicially selecting and narrowing the follow-on packages for evaluation and testing, as well as for the low risk insertion in high-reliability applications.

Using Gemba Boards to Facilitate Evidence-Based Practice in Critical Care.

PubMed

Bourgault, Annette M; Upvall, Michele J; Graham, Alison

2018-06-01

Tradition-based practices lack supporting research evidence and may be harmful or ineffective. Engagement of key stakeholders is a critical step toward facilitating evidence-based practice change. Gemba , derived from Japanese, refers to the real place where work is done. Gemba boards (visual management tools) appear to be an innovative method to engage stakeholders and facilitate evidence-based practice. To explore the use of gemba boards and gemba huddles to facilitate practice change. Twenty-two critical care nurses participated in interviews in this qualitative, descriptive study. Thematic analysis was used to code and categorize interview data. Two researchers reached consensus on coding and derived themes. Data were managed with qualitative analysis software. The code gemba occurred most frequently; a secondary analysis was performed to explore its impact on practice change. Four themes were derived from the gemba code: (1) facilitation of staff, leadership, and interdisciplinary communication, (2) transparency of outcome data, (3) solicitation of staff ideas and feedback, and (4) dissemination of practice changes. Gemba boards and gemba huddles became part of the organizational culture for promoting and disseminating evidence-based practices. Unit-based, publicly located gemba boards and huddles have become key components of evidence-based practice culture. Gemba is both a tool and a process to engage team members and the public to generate clinical questions and to plan, implement, and evaluate practice changes. Future research on the effectiveness of gemba boards to facilitate evidence-based practice is warranted. ©2018 American Association of Critical-Care Nurses.

Structural Integrity Recording System (SIRS) for U.S. Army AH-1G helicopters

DTIC Science & Technology

1981-03-01

location was detected during the diagnostic check of the recorder’s data storage memory. BATTERY Denotes that the recorder’s battery power supply is...Condition- ing Board 074032D30019 50.6592 19,740 Power Supply CS/TlS/165/x 16.6667 60,000 Filter RF6125 0.0560 17,857,143 *Termination Assembly 074032C30011...whatsoever; and the fact that the Government may have formulated, furnished, or in any way supplied the said drawings, specifications, or other date is

Acquisition of Ice Thickness and Ice Surface Characteristics In the Seasonal Ice Zone by CULPIS-X During the US Coast Guards Arctic Domain Awareness Program

DTIC Science & Technology

2015-09-30

as a package called CULPIS [Crocker et al., 2012 ]. The CULPIS-X instruments are designed to acquire: • Distance to surface measured at 400...Control Board (ACCB) request was re-initiated in early 2015 with the USCG ALC by our POC in Kodiak, AK, LT. William Coombs . The CFD and FED data were...X Assembly manual and an Operations Manual for use by the USCG. These documents were requested by our USCG Kodiak contact, LT. William Coombs

Integrated testing system FiTest for diagnosis of PCBA

NASA Astrophysics Data System (ADS)

Bogdan, Arkadiusz; Lesniak, Adam

2016-12-01

This article presents the innovative integrated testing system FiTest for automatic, quick inspection of printed circuit board assemblies (PCBA) manufactured in Surface Mount Technology (SMT). Integration of Automatic Optical Inspection (AOI), In-Circuit Tests (ICT) and Functional Circuit Tests (FCT) resulted in universal hardware platform for testing variety of electronic circuits. The platform provides increased test coverage, decreased level of false calls and optimization of test duration. The platform is equipped with powerful algorithms performing tests in a stable and repetitive way and providing effective management of diagnosis.

Attitude sensor package

NASA Technical Reports Server (NTRS)

Aceti, R.; Trischberger, M.; Underwood, P. J.; Pomilia, A.; Cosi, M.; Boldrini, F.

1993-01-01

This paper describes the design, construction, testing, and successful flight of the Attitude Sensor Package. The payload was assembled on a standard HITCHHIKER experiment mounting plate, and made extensive use of the carrier's power and data handling capabilities. The side mounted HITCHHIKER version was chosen, since this configuration provided the best viewing conditions for the instruments. The combustion was successfully flown on board Space Shuttle Columbia (STS-52), in October 1992. The payload was one of the 14 experiments of the In-Orbit Technology Demonstration Program (Phase 1) of the European Space Agency.

CoCoFolio: A Web-Based Electronic Portfolio for Enriching Students' Learning by Collaboration.

ERIC Educational Resources Information Center

Sugiyama, Takeshi; Kakehi, Naoyuki; Kura, Tsuneko; Takahashi Tokiichiro

A Web-based electronic portfolio, CoCoFolio, was developed for enriching students' learning by collaboration. CoCoFolio consists of two collaboration tools: a multi-layer drawing tool, CoCoBoard, and a small bulletin board, Discussion Board, for each student's submission. These tools support a series of expression activities: expression, sharing,…

Development of a beam test telescope based on the Alibava readout system

NASA Astrophysics Data System (ADS)

Marco-Hernández, R.

2011-01-01

A telescope for a beam test have been developed as a result of a collaboration among the University of Liverpool, Centro Nacional de Microelectrónica (CNM) of Barcelona and Instituto de Física Corpuscular (IFIC) of Valencia. This system is intended to carry out both analogue charge collection and spatial resolution measurements with different types of microstrip or pixel silicon detectors in a beam test environment. The telescope has four XY measurement as well as trigger planes (XYT board) and it can accommodate up to twelve devices under test (DUT board). The DUT board uses two Beetle ASICs for the readout of chilled silicon detectors. The board could operate in a self-triggering mode. The board features a temperature sensor and it can be mounted on a rotary stage. A peltier element is used for cooling the DUT. Each XYT board measures the track space points using two silicon strip detectors connected to two Beetle ASICs. It can also trigger on the particle tracks in the beam test. The board includes a CPLD which allows for the synchronization of the trigger signal to a common clock frequency, delaying and implementing coincidence with other XYT boards. An Alibava mother board is used to read out and to control each XYT/DUT board from a common trigger signal and a common clock signal. The Alibava board has a TDC on board to have a time stamp of each trigger. The data collected by each Alibava board is sent to a master card by means of a local data/address bus following a custom digital protocol. The master board distributes the trigger, clock and reset signals. It also merges the data streams from up to sixteen Alibava boards. The board has also a test channel for testing in a standard mode a XYT or DUT board. This board is implemented with a Xilinx development board and a custom patch board. The master board is connected with the DAQ software via 100M Ethernet. Track based alignment software has also been developed for the data obtained with the DAQ software.

Colloidosome like structures: self-assembly of silica microrods

DOE PAGES

Datskos, P.; Polizos, G.; Bhandari, M.; ...

2016-03-07

Self-assembly of one-dimensional structures is attracting a great deal of interest because assembled structures can provide better properties compared to individual building blocks. We demonstrate silica microrod self-assembly by exploiting Pickering emulsion based strategy. Micron-sized silica rods were synthesized employing previously reported methods based on polyvinylpyrrolidone/ pentanol emulsion droplets. Moreover, rods self-assembled to make structures in the range of z10 40 mm. Smooth rods assembled better than segmented rods. Finally, the assembled structures were bonded by weak van der Waals forces.

Polyplanar optical display electronics

NASA Astrophysics Data System (ADS)

DeSanto, Leonard; Biscardi, Cyrus

1997-07-01

The polyplanar optical display (POD) is a unique display screen which can be used with any projection source. The prototype ten inch display is two inches thick and has a matte black face which allows for high contrast images. The prototype being developed is a form, fit and functional replacement display for the B-52 aircraft which uses a monochrome ten-inch display. In order to achieve a long lifetime, the new display uses a 100 milliwatt green solid- state laser at 532 nm as its light source. To produce real- time video, the laser light is being modulated by a digital light processing (DLP) chip manufactured by Texas Instruments. In order to use the solid-state laser as the light source and also fit within the constraints of the B-52 display, the digital micromirror device (DMD) circuit board is removed from the Texas Instruments DLP light engine assembly. Due to the compact architecture of the projection system within the display chassis, the DMD chip is operated remotely from the Texas Instruments circuit board. We discuss the operation of the DMD divorced from the light engine and the interfacing of the DMD board with various video formats including the format specific to the B-52 aircraft. A brief discussion of the electronics required to drive the laser is also presented.

Assembling surface mounted components on ink-jet printed double sided paper circuit board.

PubMed

Andersson, Henrik A; Manuilskiy, Anatoliy; Haller, Stefan; Hummelgård, Magnus; Sidén, Johan; Hummelgård, Christine; Olin, Håkan; Nilsson, Hans-Erik

2014-03-07

Printed electronics is a rapidly developing field where many components can already be manufactured on flexible substrates by printing or by other high speed manufacturing methods. However, the functionality of even the most inexpensive microcontroller or other integrated circuit is, at the present time and for the foreseeable future, out of reach by means of fully printed components. Therefore, it is of interest to investigate hybrid printed electronics, where regular electrical components are mounted on flexible substrates to achieve high functionality at a low cost. Moreover, the use of paper as a substrate for printed electronics is of growing interest because it is an environmentally friendly and renewable material and is, additionally, the main material used for many packages in which electronics functionalities could be integrated. One of the challenges for such hybrid printed electronics is the mounting of the components and the interconnection between layers on flexible substrates with printed conductive tracks that should provide as low a resistance as possible while still being able to be used in a high speed manufacturing process. In this article, several conductive adhesives are evaluated as well as soldering for mounting surface mounted components on a paper circuit board with ink-jet printed tracks and, in addition, a double sided Arduino compatible circuit board is manufactured and programmed.

Solder Flux Residues and Humidity-Related Failures in Electronics: Relative Effects of Weak Organic Acids Used in No-Clean Flux Systems

NASA Astrophysics Data System (ADS)

Verdingovas, Vadimas; Jellesen, Morten Stendahl; Ambat, Rajan

2015-04-01

This paper presents the results of humidity testing of weak organic acids (WOAs), namely adipic, succinic, glutaric, dl-malic, and palmitic acids, which are commonly used as activators in no-clean solder fluxes. The study was performed under humidity conditions varying from 60% relative humidity (RH) to ˜99%RH at 25°C. The following parameters were used for characterization of WOAs: mass gain due to water adsorption and deliquescence of the WOA (by quartz crystal microbalance), resistivity of the water layer formed on the printed circuit board (by impedance spectroscopy), and leakage current measured using the surface insulation resistance pattern in the potential range from 0 V to 10 V. The combined results indicate the importance of the WOA chemical structure for the water adsorption and therefore conductive water layer formation on the printed circuit board assembly (PCBA). A substantial increase of leakage currents and probability of electrochemical migration was observed at humidity levels above the RH corresponding to the deliquescence point of WOAs present as contaminants on the printed circuit boards. The results suggest that use of solder fluxes with WOAs having higher deliquescence point could improve the reliability of electronics operating under circumstances in which exposure to high humidity is likely to occur.

Common Board Design for the OBC I/O Unit and The OBC CCSDS Unit of The Stuttgart University Satellite "Flying Laptop"

NASA Astrophysics Data System (ADS)

Eickhoff, Jens; Cook, Barry; Walker, Paul; Habinc, Sadi; Witt, Rouven; Roser, Hans-Peter

2011-08-01

As already published in another paper at DASIA 2010 in Budapest [1] the University of Stuttgart, Germany, is developing an advanced 3-axis stabilized small satellite applying industry standards for command/control techniques, onboard software design and onboard computer components.The satellite has a launch mass of approx. 120kg and is foreseen to be launched end 2013 as piggy back payload on an Indian PSLV launcher.During phase C the main challenge was the conceptual design for an ultra compact and performant onboard computer (OBC), which is able to support an industry standard operating system, a PUS standard based onboard software (OBSW) and CCSDS standard based ground/space communication. The developed architecture is based on 4 main elements (see [1] and Figure 4):• the OBC core board (single board computer based on LEON3 FT architecture),• an I/O Board for all OBC digital interfaces to S/C equipment,• a CCSDS TC/TM pre-processor board,• CPDU being embedded in the PCDU.The EM for the OBC core meanwhile has been shipped to the University by the supplier Aeroflex Colorado Springs, USA and is in use in Stuttgart since January 2011. Figure 2 and Figure 3 provide brief impressions. This paper concentrates on the common design of the I/O board and the CCSDS processor boards.

Elemental analysis of printed circuit boards considering the ROHS regulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wienold, Julia, E-mail: julia.wienold@bam.de; Recknagel, Sebastian, E-mail: sebastian.recknagel@bam.de; Scharf, Holger, E-mail: holger.scharf@bam.de

2011-03-15

The EU RoHS Directive (2002/95/EC of the European Parliament and of the Council) bans the placing of new electrical and electronic equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants on the EU market. It necessitates methods for the evaluation of RoHS compliance of assembled electronic equipment. In this study mounted printed circuit boards from personal computers were analyzed on their content of the three elements Cd, Pb and Hg which were limited by the EU RoHS directive. Main focus of the investigations was the influence ofmore » sample pre-treatment on the precision and reproducibility of the results. The sample preparation steps used were based on the guidelines given in EN 62321. Five different types of dissolution procedures were tested on different subsequent steps of sample treatment like cutting and milling. Elemental analysis was carried out using ICP-OES, XRF and CV-AFS (Hg). The results obtained showed that for decision-making with respect to RoHS compliance a size reduction of the material to be analyzed to particles {<=}1.5 mm can already be sufficient. However, to ensure analytical results with relative standard deviations of less than 20%, as recommended by the EN 62321, a much larger effort for sample processing towards smaller particle sizes might be required which strongly depends on the mass fraction of the element under investigation.« less

High-Rate Assembly of Nanomaterials on Insulating Surfaces Using Electro-Fluidic Directed Assembly.

PubMed

Yilmaz, Cihan; Sirman, Asli; Halder, Aditi; Busnaina, Ahmed

2017-08-22

Conductive or semiconducting nanomaterials-based applications such as electronics and sensors often require direct placement of such nanomaterials on insulating surfaces. Most fluidic-based directed assembly techniques on insulating surfaces utilize capillary force and evaporation but are diffusion limited and slow. Electrophoretic-based assembly, on the other hand, is fast but can only be utilized for assembly on a conductive surface. Here, we present a directed assembly technique that enables rapid assembly of nanomaterials on insulating surfaces. The approach leverages and combines fluidic and electrophoretic assembly by applying the electric field through an insulating surface via a conductive film underneath. The approach (called electro-fluidic) yields an assembly process that is 2 orders of magnitude faster compared to fluidic assembly. By understanding the forces on the assembly process, we have demonstrated the controlled assembly of various types of nanomaterials that are conducting, semiconducting, and insulating including nanoparticles and single-walled carbon nanotubes on insulating rigid and flexible substrates. The presented approach shows great promise for making practical devices in miniaturized sensors and flexible electronics.

Bridging existing governance gaps: five evidence-based actions that boards can take to pursue high quality care.

PubMed

Leggat, Sandra G; Balding, Cathy

2017-11-13

Objective To explore the impact of the organisational quality systems on quality of care in Victorian health services. Methods During 2015 a total of 55 focus groups were conducted with more than 350 managers, clinical staff and board members in eight Victorian health services to explore the effectiveness of health service quality systems. A review of the quality and safety goals and strategies outlined in the strategic and operating plans of the participating health services was also undertaken. Results This paper focuses on the data related to the leadership role of health service boards in ensuring safe, high-quality care. The findings suggest that health service boards are not fully meeting their governance accountability to ensure consistently high-quality care. The data uncovered major clinical governance gaps between stated board and executive aspirations for quality and safety and the implementation of these expectations at point of care. These gaps were further compounded by quality system confusion, over-reliance on compliance, and inadequate staff engagement. Conclusion Based on the existing evidence we propose five specific actions boards can take to close the gaps, thereby supporting improved care for all consumers. What is known about this topic? Effective governance is essential for high-quality healthcare delivery. Boards are required to play an active role in their organisation's pursuit of high quality care. What does this paper add? Recent government reports suggest that Australian health service boards are not fully meeting their governance requirements for high quality, safe care delivery, and our research pinpoints key governance gaps. What are the implications for practitioners? Based on our research findings we outline five evidence-based actions for boards to improve their governance of quality care delivery. These actions focus on an organisational strategy for high-quality care, with the chief executive officer held accountable for successful implementation, which is actively guided and monitored by the board.

Possibility of using waste tire composites reinforced with rice straw as construction materials.

PubMed

Yang, Han-Seung; Kim, Dae-Jun; Lee, Young-Kyu; Kim, Hyun-Joong; Jeon, Jin-Yong; Kang, Chun-Won

2004-10-01

Agricultural lignocellulosic fiber (rice straw)-waste tire particle composite boards were manufactured for use as insulation boards in construction, using the same method as that used in the wood-based panel industry. The manufacturing parameters were: a specific gravity of 0.8 and a rice straw content (10/90, 20/80 and 30/70 by wt.% of rice straw/waste tire particle). A commercial polyurethane adhesive for rubber was used as the composite binder. The water proof, water absorption and thickness swelling properties of the composite boards were better than those of wood particleboard. Furthermore, the flexibility and flexural properties of the composite boards were superior to those of other wood-based panel products. The composite boards also demonstrated good acoustical insulation, electrical insulation, anti-caustic and anti-rot properties. These boards can be used to prevent impact damage, are easily modifiable and are inexpensive. They are able to be used as a substitute for insulation boards and other flexural materials in construction.

An assembly process model based on object-oriented hierarchical time Petri Nets

NASA Astrophysics Data System (ADS)

Wang, Jiapeng; Liu, Shaoli; Liu, Jianhua; Du, Zenghui

2017-04-01

In order to improve the versatility, accuracy and integrity of the assembly process model of complex products, an assembly process model based on object-oriented hierarchical time Petri Nets is presented. A complete assembly process information model including assembly resources, assembly inspection, time, structure and flexible parts is established, and this model describes the static and dynamic data involved in the assembly process. Through the analysis of three-dimensional assembly process information, the assembly information is hierarchically divided from the whole, the local to the details and the subnet model of different levels of object-oriented Petri Nets is established. The communication problem between Petri subnets is solved by using message database, and it reduces the complexity of system modeling effectively. Finally, the modeling process is presented, and a five layer Petri Nets model is established based on the hoisting process of the engine compartment of a wheeled armored vehicle.

FPGA and USB based control board for quantum random number generator

NASA Astrophysics Data System (ADS)

Wang, Jian; Wan, Xu; Zhang, Hong-Fei; Gao, Yuan; Chen, Teng-Yun; Liang, Hao

2009-09-01

The design and implementation of FPGA-and-USB-based control board for quantum experiments are discussed. The usage of quantum true random number generator, control- logic in FPGA and communication with computer through USB protocol are proposed in this paper. Programmable controlled signal input and output ports are implemented. The error-detections of data frame header and frame length are designed. This board has been used in our decoy-state based quantum key distribution (QKD) system successfully.

Structural Design and Analysis of a Light-Weight Laminated Composite Heat Sink for Spaceflight PWBs

NASA Technical Reports Server (NTRS)

Fan, Mark S.; Niemeyer, W. Lee

1997-01-01

In order to reduce the overall weight in spaceborne electronic systems, a conventional metallic heat sink typically used for double-sided printed wiring boards was suggested to be replaced by light-weight and high-strength laminated composite materials. Through technology validation assurance (TVA) approach, it has been successfully demonstrated that using laminated composite heat sink can not only reduce the weight of the heat sink by nearly 50%, but also significantly lower the internal thermally-induced stresses that are largely responsible for potential delamination under cyclic temperature variations. With composite heat sink, both thermal and dynamic performance of the double-sided printed wiring board (PWB) exceeds that of its counterpart with metallic heat sink. Also included in this work is the original contribution to the understanding of creep behavior of the worst-case leadless chip carrier (LCC) surface mount solder joint. This was identified as the interconnection most susceptible to thermal fatigue damage in the PWB assembly.

Thermal and optical aspects of glob-top design for phosphor converted white LED light sources

NASA Astrophysics Data System (ADS)

Sommer, Christian; Fulmek, Paul; Nicolics, Johann; Schweitzer, Susanne; Nemitz, Wolfgang; Hartmann, Paul; Pachler, Peter; Hoschopf, Hans; Schrank, Franz; Langer, Gregor; Wenzl, Franz P.

2013-09-01

For a systematic approach to improve the white light quality of phosphor converted light-emitting diodes (LEDs) for general lighting applications it is imperative to get the individual sources of error for correlated color temperature (CCT) reproducibility and maintenance under control. In this regard, it is of essential importance to understand how geometrical, optical and thermal properties of the color conversion elements (CCE), which typically consist of phosphor particles embedded in a transparent matrix material, affect the constancy of a desired CCT value. In this contribution we use an LED assembly consisting of an LED die mounted on a printed circuit board by chip-on-board technology and a CCE with a glob-top configuration on the top of it as a model system and discuss the impact of the CCE shape and size on CCT constancy with respect to substrate reflectivity and thermal load of the CCEs. From these studies, some general conclusions for improved glob-top design can be drawn.

Trusted to the Rulers of the People Alone: A Legal Analysis of the Constitutionality of Removing Locally Elected School Board Members in Georgia

ERIC Educational Resources Information Center

Collier Good, Cayanna

2013-01-01

This dissertation explored the constitutionality of a Georgia law, under both the Georgia Constitution and the United States Constitution, which allows for the removal of elected school board members based on threatened loss of district accreditation. The problem is that elected board members are being removed from office based on district…

49 CFR 229.23 - Periodic inspection: general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... locomotive. (b) For each locomotive equipped with advanced microprocessor-based on-board electronic condition... April 2, or July 3 if it's a locomotive equipped with advanced microprocessor-based on-board electronic...

49 CFR 229.23 - Periodic inspection: general.

Code of Federal Regulations, 2013 CFR

2013-10-01

... locomotive. (b) For each locomotive equipped with advanced microprocessor-based on-board electronic condition... April 2, or July 3 if it's a locomotive equipped with advanced microprocessor-based on-board electronic...

49 CFR 229.23 - Periodic inspection: general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... locomotive. (b) For each locomotive equipped with advanced microprocessor-based on-board electronic condition... April 2, or July 3 if it's a locomotive equipped with advanced microprocessor-based on-board electronic...

Improved Scanners for Microscopic Hyperspectral Imaging

NASA Technical Reports Server (NTRS)

Mao, Chengye

2009-01-01

Improved scanners to be incorporated into hyperspectral microscope-based imaging systems have been invented. Heretofore, in microscopic imaging, including spectral imaging, it has been customary to either move the specimen relative to the optical assembly that includes the microscope or else move the entire assembly relative to the specimen. It becomes extremely difficult to control such scanning when submicron translation increments are required, because the high magnification of the microscope enlarges all movements in the specimen image on the focal plane. To overcome this difficulty, in a system based on this invention, no attempt would be made to move either the specimen or the optical assembly. Instead, an objective lens would be moved within the assembly so as to cause translation of the image at the focal plane: the effect would be equivalent to scanning in the focal plane. The upper part of the figure depicts a generic proposed microscope-based hyperspectral imaging system incorporating the invention. The optical assembly of this system would include an objective lens (normally, a microscope objective lens) and a charge-coupled-device (CCD) camera. The objective lens would be mounted on a servomotor-driven translation stage, which would be capable of moving the lens in precisely controlled increments, relative to the camera, parallel to the focal-plane scan axis. The output of the CCD camera would be digitized and fed to a frame grabber in a computer. The computer would store the frame-grabber output for subsequent viewing and/or processing of images. The computer would contain a position-control interface board, through which it would control the servomotor. There are several versions of the invention. An essential feature common to all versions is that the stationary optical subassembly containing the camera would also contain a spatial window, at the focal plane of the objective lens, that would pass only a selected portion of the image. In one version, the window would be a slit, the CCD would contain a one-dimensional array of pixels, and the objective lens would be moved along an axis perpendicular to the slit to spatially scan the image of the specimen in pushbroom fashion. The image built up by scanning in this case would be an ordinary (non-spectral) image. In another version, the optics of which are depicted in the lower part of the figure, the spatial window would be a slit, the CCD would contain a two-dimensional array of pixels, the slit image would be refocused onto the CCD by a relay-lens pair consisting of a collimating and a focusing lens, and a prism-gratingprism optical spectrometer would be placed between the collimating and focusing lenses. Consequently, the image on the CCD would be spatially resolved along the slit axis and spectrally resolved along the axis perpendicular to the slit. As in the first-mentioned version, the objective lens would be moved along an axis perpendicular to the slit to spatially scan the image of the specimen in pushbroom fashion.

Pegasus XL CYGNSS Move to AIT

NASA Image and Video Library

2016-11-17

At Vandenberg Air Force Base in California, an Orbital ATK Pegasus XL rocket is placed on an assembly integration transporter for the move from the hangar at Building 1555 to be mated to L-1011 carrier aircraft near Vandenberg's runway. On board Pegasus are eight NASA Cyclone Global Navigation Satellite System, or CYGNSS, spacecraft. When preparations are competed at Vandenberg, the L-1011/Pegasus XL combination will be flown to NASA’s Kennedy Space Center in Florida. On Dec. 12, 2016, the carrier aircraft is scheduled to take off from the Skid Strip at Cape Canaveral Air Force Station and CYGNSS will launch on the Pegasus XL rocket with the L-1011 flying off shore. CYGNSS satellites will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes. The data that CYGNSS provides will enable scientists to probe key air-sea interaction processes that take place near the core of storms, which are rapidly changing and play a critical role in the beginning and intensification of hurricanes.

A Micro Aerosol Sensor for the Measurement of Airborne Ultrafine Particles.

PubMed

Zhang, Chao; Zhu, Rong; Yang, Wenming

2016-03-18

Particle number concentration and particle size are the two key parameters used to characterize exposure to airborne nanoparticles or ultrafine particles that have attracted the most attention. This paper proposes a simple micro aerosol sensor for detecting the number concentration and particle size of ultrafine particles with diameters from 50 to 253 nm based on electrical diffusion charging. The sensor is composed of a micro channel and a couple of planar electrodes printed on two circuit boards assembled in parallel, which thus integrate charging, precipitating and measurement elements into one chip, the overall size of which is 98 × 38 × 25 mm³. The experiment results demonstrate that the sensor is useful for measuring monodisperse aerosol particles with number concentrations from 300 to 2.5 × 10⁴ /cm³ and particle sizes from 50 to 253 nm. The aerosol sensor has a simple structure and small size, which is favorable for use in handheld devices.

A Micro Aerosol Sensor for the Measurement of Airborne Ultrafine Particles

PubMed Central

Zhang, Chao; Zhu, Rong; Yang, Wenming

2016-01-01

Particle number concentration and particle size are the two key parameters used to characterize exposure to airborne nanoparticles or ultrafine particles that have attracted the most attention. This paper proposes a simple micro aerosol sensor for detecting the number concentration and particle size of ultrafine particles with diameters from 50 to 253 nm based on electrical diffusion charging. The sensor is composed of a micro channel and a couple of planar electrodes printed on two circuit boards assembled in parallel, which thus integrate charging, precipitating and measurement elements into one chip, the overall size of which is 98 × 38 × 25 mm3. The experiment results demonstrate that the sensor is useful for measuring monodisperse aerosol particles with number concentrations from 300 to 2.5 × 104 /cm3 and particle sizes from 50 to 253 nm. The aerosol sensor has a simple structure and small size, which is favorable for use in handheld devices. PMID:26999156

Enhanced data consistency of a portable gait measurement system.

PubMed

Lin, Hsien-I; Chiang, Y P

2013-11-01

A gait measurement system is a useful tool for rehabilitation applications. Such a system is used to conduct gait experiments in large workplaces such as laboratories where gait measurement equipment can be permanently installed. However, a gait measurement system should be portable if it is to be used in clinics or community centers for aged people. In a portable gait measurement system, the workspace is limited and landmarks on a subject may not be visible to the cameras during experiments. Thus, we propose a virtual-marker function to obtain positions of unseen landmarks for maintaining data consistency. This work develops a portable clinical gait measurement system consisting of lightweight motion capture devices, force plates, and a walkway assembled from plywood boards. We evaluated the portable clinic gait system with 11 normal subjects in three consecutive days in a limited experimental space. Results of gait analysis based on the verification of within-day and between-day coefficients of multiple correlations show that the proposed portable gait system is reliable.

RoboGlove-A Grasp Assist Device for Earth and Space

NASA Technical Reports Server (NTRS)

Diftler, M. A.; Ihrke, C. A.; Bridgwater, L. B.; Rogers, J. M.; Davis, D. R.; Linn, D. M.; Laske, E. A.; Ensley, K. G.; Lee, J. H.

2015-01-01

The RoboGlove is an assistive device that can augment human strength, endurance or provide directed motion for use in rehabilitation. RoboGlove is a spinoff of the highly successful Robonaut 2 (R2) system developed as part of a partnership between General Motors and NASA. This extremely lightweight device employs an actuator system based on the R2 finger drive system to transfer part or the entire grasp load from human tendons to artificial ones contained in the glove. Steady state loads ranging from 15 to 20 lbs. and peaks approaching 50 lbs. are achievable. Work is underway to integrate the RoboGlove system with a space suit glove to add strength or reduce fatigue during spacewalks. Tactile sensing, miniaturized electronics, and on-board processing provide sufficient flexibility for applications in many industries. The following describes the design, mechanical/electrical integration, and control features of the glove in an assembly-line configuration and discusses work toward the space suit application.

The optical design of 3D ICs for smartphone and optro-electronics sensing module

NASA Astrophysics Data System (ADS)

Huang, Jiun-Woei

2018-03-01

Smartphone require limit space for image system, current lens, used in smartphones are refractive type, the effective focal length is limited the thickness of phone physical size. Other, such as optro-electronics sensing chips, proximity optical sensors, and UV indexer chips are integrated into smart phone with limit space. Due to the requirement of multiple lens in smartphone, proximity optical sensors, UV indexer and other optro-electronics sensing chips in a limited space of CPU board in future smart phone, optro-electronics 3D IC's integrated with optical lens or components may be a key technology for 3 C products. A design for reflective lens is fitted to CMOS, proximity optical sensors, UV indexer and other optro-electronics sensing chips based on 3-D IC. The reflective lens can be threes times of effective focal lens, and be able to resolve small object. The system will be assembled and integrated in one 3-D IC more easily.

Waveguide metatronics: Lumped circuitry based on structural dispersion

PubMed Central

Li, Yue; Liberal, Iñigo; Della Giovampaola, Cristian; Engheta, Nader

2016-01-01

Engineering optical nanocircuits by exploiting modularization concepts and methods inherited from electronics may lead to multiple innovations in optical information processing at the nanoscale. We introduce the concept of “waveguide metatronics,” an advanced form of optical metatronics that uses structural dispersion in waveguides to obtain the materials and structures required to construct this class of circuitry. Using numerical simulations, we demonstrate that the design of a metatronic circuit can be carried out by using a waveguide filled with materials with positive permittivity. This includes the implementation of all “lumped” circuit elements and their assembly in a single circuit board. In doing so, we extend the concepts of optical metatronics to frequency ranges where there are no natural plasmonic materials available. The proposed methodology could be exploited as a platform to experimentally validate optical metatronic circuits in other frequency regimes, such as microwave frequency setups, and/or to provide a new route to design optical nanocircuitry. PMID:27386566

Enhanced data consistency of a portable gait measurement system

NASA Astrophysics Data System (ADS)

Lin, Hsien-I.; Chiang, Y. P.

2013-11-01

A gait measurement system is a useful tool for rehabilitation applications. Such a system is used to conduct gait experiments in large workplaces such as laboratories where gait measurement equipment can be permanently installed. However, a gait measurement system should be portable if it is to be used in clinics or community centers for aged people. In a portable gait measurement system, the workspace is limited and landmarks on a subject may not be visible to the cameras during experiments. Thus, we propose a virtual-marker function to obtain positions of unseen landmarks for maintaining data consistency. This work develops a portable clinical gait measurement system consisting of lightweight motion capture devices, force plates, and a walkway assembled from plywood boards. We evaluated the portable clinic gait system with 11 normal subjects in three consecutive days in a limited experimental space. Results of gait analysis based on the verification of within-day and between-day coefficients of multiple correlations show that the proposed portable gait system is reliable.

The Fermilab lattice supercomputer project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischler, M.; Atac, R.; Cook, A.

1989-02-01

The ACPMAPS system is a highly cost effective, local memory MIMD computer targeted at algorithm development and production running for gauge theory on the lattice. The machine consists of a compound hypercube of crates, each of which is a full crossbar switch containing several processors. The processing nodes are single board array processors based on the Weitek XL chip set, each with a peak power of 20 MFLOPS and supported by 8 MBytes of data memory. The system currently being assembled has a peak power of 5 GFLOPS, delivering performance at approximately $250/MFLOP. The system is programmable in C andmore » Fortran. An underpinning of software routines (CANOPY) provides an easy and natural way of coding lattice problems, such that the details of parallelism, and communication and system architecture are transparent to the user. CANOPY can easily be ported to any single CPU or MIMD system which supports C, and allows the coding of typical applications with very little effort. 3 refs., 1 fig.« less

Simple-1: Development stage of the data transmission system for a solid propellant mid-power rocket model

NASA Astrophysics Data System (ADS)

Yarce, Andrés; Sebastián Rodríguez, Juan; Galvez, Julián; Gómez, Alejandro; García, Manuel J.

2017-06-01

This paper presents the development stage of a communication module for a solid propellant mid-power rocket model. The communication module was named. Simple-1 and this work considers its design, construction and testing. A rocket model Estes Ventris Series Pro II® was modified to introduce, on the top of the payload, several sensors in a CanSat form factor. The Printed Circuit Board (PCB) was designed and fabricated from Commercial Off The Shelf (COTS) components and assembled in a cylindrical rack structure similar to this small format satellite concept. The sensors data was processed using one Arduino Mini and transmitted using a radio module to a Software Defined Radio (SDR) HackRF based platform on the ground station. The Simple-1 was tested using a drone in successive releases, reaching altitudes from 200 to 300 meters. Different kind of data, in terms of altitude, position, atmospheric pressure and vehicle temperature were successfully measured, making possible the progress to a next stage of launching and analysis.

Improved Miniaturized Linear Ion Trap Mass Spectrometer Using Lithographically Patterned Plates and Tapered Ejection Slit

NASA Astrophysics Data System (ADS)

Tian, Yuan; Decker, Trevor K.; McClellan, Joshua S.; Bennett, Linsey; Li, Ailin; De la Cruz, Abraham; Andrews, Derek; Lammert, Stephen A.; Hawkins, Aaron R.; Austin, Daniel E.

2018-02-01

We present a new two-plate linear ion trap mass spectrometer that overcomes both performance-based and miniaturization-related issues with prior designs. Borosilicate glass substrates are patterned with aluminum electrodes on one side and wire-bonded to printed circuit boards. Ions are trapped in the space between two such plates. Tapered ejection slits in each glass plate eliminate issues with charge build-up within the ejection slit and with blocking of ions that are ejected at off-nominal angles. The tapered slit allows miniaturization of the trap features (electrode size, slit width) needed for further reduction of trap size while allowing the use of substrates that are still thick enough to provide ruggedness during handling, assembly, and in-field applications. Plate spacing was optimized during operation using a motorized translation stage. A scan rate of 2300 Th/s with a sample mixture of toluene and deuterated toluene (D8) and xylenes (a mixture of o-, m-, p-) showed narrowest peak widths of 0.33 Th (FWHM).

Investigation into the Educational Process of Cancer Case Conferences.

ERIC Educational Resources Information Center

Nyquist, Julie G.; And Others

1990-01-01

This study investigated the educational process used in tumor boards (cancer case conferences) and whether the process varied based on type of board, frequency of meetings, and presence or absence of residency training programs in the hospital. These data were collected through observation of 715 board sessions of 37 hospitals and 43 tumor boards.…

A study on the real-time reliability of on-board equipment of train control system

NASA Astrophysics Data System (ADS)

Zhang, Yong; Li, Shiwei

2018-05-01

Real-time reliability evaluation is conducive to establishing a condition based maintenance system for the purpose of guaranteeing continuous train operation. According to the inherent characteristics of the on-board equipment, the connotation of reliability evaluation of on-board equipment is defined and the evaluation index of real-time reliability is provided in this paper. From the perspective of methodology and practical application, the real-time reliability of the on-board equipment is discussed in detail, and the method of evaluating the realtime reliability of on-board equipment at component level based on Hidden Markov Model (HMM) is proposed. In this method the performance degradation data is used directly to realize the accurate perception of the hidden state transition process of on-board equipment, which can achieve a better description of the real-time reliability of the equipment.

Hubble Space Telescope: SRM/QA observations and lessons learned

NASA Technical Reports Server (NTRS)

Rodney, George A.

1990-01-01

The Hubble Space Telescope (HST) Optical Systems Board of Investigation was established on July 2, 1990 to review, analyze, and evaluate the facts and circumstances regarding the manufacture, development, and testing of the HST Optical Telescope Assembly (OTA). Specifically, the board was tasked to ascertain what caused the spherical aberration and how it escaped notice until on-orbit operation. The error that caused the on-orbit spherical aberration in the primary mirror was traced to the assembly process of the Reflective Null Corrector, one of the three Null Correctors developed as special test equipment (STE) to measure and test the primary mirror. Therefore, the safety, reliability, maintainability, and quality assurance (SRM&QA) investigation covers the events and the overall product assurance environment during the manufacturing phase of the primary mirror and Null Correctors (from 1978 through 1981). The SRM&QA issues that were identified during the HST investigation are summarized. The crucial product assurance requirements (including nonconformance processing) for the HST are examined. The history of Quality Assurance (QA) practices at Perkin-Elmer (P-E) for the period under investigation are reviewed. The importance of the information management function is discussed relative to data retention/control issues. Metrology and other critical technical issues also are discussed. The SRM&QA lessons learned from the investigation are presented along with specific recommendations. Appendix A provides the MSFC SRM&QA report. Appendix B provides supplemental reference materials. Appendix C presents the findings of the independent optical consultants, Optical Research Associates (ORA). Appendix D provides further details of the fault-tree analysis portion of the investigation process.

Band-to-Band Misregistration of the Images of MODIS On-Board Calibrators and Its Impact to Calibration

NASA Technical Reports Server (NTRS)

Wang, Zhipeng; Xiong, Xiaoxiong

2017-01-01

The MODIS instruments aboard Terra and Aqua satellites are radiometrically calibrated on-orbit with a set of onboard calibrators (OBC) including a solar diffuser (SD), a blackbody (BB) and a space view (SV) port through which the detectors can view the dark space. As a whisk-broom scanning spectroradiometer, thirty-six MODIS spectral bands are assembled in the along-scan direction on four focal plane assemblies (FPA). These bands capture images of the same target sequentially with the motion of a scan mirror. Then the images are co-registered on board by delaying appropriate band dependent amount of time depending on the band locations on the FPA. While this co-registration mechanism is functioning well for the "far field" remote targets such as Earth view (EV) scenes or the Moon, noticeable band-to-band misregistration in the along-scan direction has been observed for near field targets, in particular the OBCs. In this paper, the misregistration phenomenon is presented and analyzed. It is concluded that the root cause of the misregistration is that the rotating element of the instrument, the scan mirror, is displaced from the focus of the telescope primary mirror. The amount of the misregistration is proportional to the band location on the FPA and is inversely proportional to the distance between the target and the scan mirror. The impact of this misregistration to the calibration of MODIS bands is discussed. In particular, the calculation of the detector gain coefficient m1 of bands 8-16 (412 nm 870 nm) is improved by up to 1.5% for Aqua MODIS.

Universal Controller for Spacecraft Mechanisms

NASA Technical Reports Server (NTRS)

Levanas, Greg; McCarthy, Thomas; Hunter, Don; Buchanan, Christine; Johnson, Michael; Cozy, Raymond; Morgan, Albert; Tran, Hung

2006-01-01

An electronic control unit has been fabricated and tested that can be replicated as a universal interface between the electronic infrastructure of a spacecraft and a brushless-motor (or other electromechanical actuator) driven mechanism that performs a specific mechanical function within the overall spacecraft system. The unit includes interfaces to a variety of spacecraft sensors, power outputs, and has selectable actuator control parameters making the assembly a mechanism controller. Several control topologies are selectable and reconfigurable at any time. This allows the same actuator to perform different functions during the mission life of the spacecraft. The unit includes complementary metal oxide/semiconductor electronic components on a circuit board of a type called rigid flex (signifying flexible printed wiring along with a rigid substrate). The rigid flex board is folded to make the unit fit into a housing on the back of a motor. The assembly has redundant critical interfaces, allowing the controller to perform time-critical operations when no human interface with the hardware is possible. The controller is designed to function over a wide temperature range without the need for thermal control, including withstanding significant thermal cycling, making it usable in nearly all environments that spacecraft or landers will endure. A prototype has withstood 1,500 thermal cycles between 120 and +85 C without significant deterioration of its packaging or electronic function. Because there is no need for thermal control and the unit is addressed through a serial bus interface, the cabling and other system hardware are substantially reduced in quantity and complexity, with corresponding reductions in overall spacecraft mass and cost.

Intracardiac ultrasound scanner using a micromachine (MEMS) actuator.

PubMed

Zara, J M; Bobbio, S M; Goodwin-Johansson, S; Smith, S W

2000-01-01

Catheter-based intracardiac ultrasound offers the potential for improved guidance of interventional cardiac procedures. The objective of this research is the development of catheter-based mechanical sector scanners incorporating high frequency ultrasound transducers operating at frequencies up to 20 MHz. The authors' current transducer assembly consists of a single 1.75 mm by 1.75 mm, 20 MHz, PZT element mounted on a 2 mm by 2 mm square, 75 mum thick polyimide table that pivots on 3-mum thick gold plated polyimide hinges. The hinges also serve as the electrical connections to the transducer. This table-mounted transducer is tilted using a miniature linear actuator to produce a sector scan. This linear actuator is an integrated force array (IFA), which is an example of a micromachine, i.e., a microelectromechanical system (MEMS). The IFA is a thin (2.2 mum) polyimide membrane, which consists of a network of hundreds of thousands of micron scale deformable capacitors made from pairs of metallized polyimide plates. IFAs contract with an applied voltage of 30-120 V and have been shown to produce strains as large as 20% and forces of up to 8 dynes. The prototype transducer and actuator assembly was fabricated and interfaced with a GagePCI analog to digital conversion board digitizing 12 bit samples at a rate of 100 MSamples/second housed in a personal computer to create a single channel ultrasound scanner. The deflection of the table transducer in a low viscosity insulating fluid (HFE 7100, 3M) is up to +/-10 degrees at scan rates of 10-60 Hz. Software has been developed to produce real-time sector scans on the PC monitor.

On a Three-Channel Cosmic Ray Detector based on Aluminum Blocks

NASA Astrophysics Data System (ADS)

Arceo, L.; Félix, J.

2017-10-01

There are many general purpose cosmic ray detectors based on plastic scintillators and electronic boards from the market. This is a new cosmic ray detector designed on three 2.54 cm × 5.08 cm × 20.32 cm Aluminum blocks in stack arrangement, and three Hamamatsu S12572-100P photodiodes. The photodiode board, the passive electronic board, and the discriminator board are own designed. The electronic signals are stored with a CompactRIO -cRIO- by National Instruments. It is presented the design, the construction, the data acquisition system algorithm, and the preliminary physical results.

The present triumphs and future problems with wave soldering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vianco, P.T.

1993-10-01

Nearly 40 years of experience with wave soldering have resulted in processes that routinely produce several thousand, defect-free solder joints per minute. However, the climate of electronics manufacturing has changed significantly over the past 10 to 15 years. Environmental restrictions as well as the high quality of products made offshore has placed new demands and challenges on the electronics industry, right down to the assembly process. The impact on wave soldering by environmental regulations and a need for more cost-competitive manufacturing processes has become a serious issue in terms of the economical well-being of the industry. In order to obtainmore » a clearer understanding of the situation, however, it is first most appropriate and necessary to examine the technology of wave soldering. Historically, wave soldering was developed as a refinement of the dip and drag soldering processes with the objective of reducing or eliminating many of the associated defects often present in these earlier processes. Wave soldering reduces the area of contact between the circuit board and the solder. This characteristic, coupled with the agitation generated in the solder, allows flux and its volatile by-products to readily escape from under the board, decreasing the number of skips, unfilled holes, and solder joint voids. The reduced contact area also lessens the potential for thermal damage to the circuit board laminate. Control of the wave profile at the exit point of the circuit board lessens the likelihood of icicles and bridges forming on the solder joints; this latitude is not available in the dip soldering process.« less

Multiple assembly chaperones govern biogenesis of the proteasome regulatory particle base.

PubMed

Funakoshi, Minoru; Tomko, Robert J; Kobayashi, Hideki; Hochstrasser, Mark

2009-05-29

The central protease of eukaryotes, the 26S proteasome, has a 20S proteolytic core particle (CP) and an attached 19S regulatory particle (RP). The RP is further subdivided into lid and base subcomplexes. Little is known about RP assembly. Here, we show that four conserved assembly factors govern biogenesis of the yeast RP base. Nas2 forms a complex with the Rpt4 and Rpt5 ATPases and enhances 26S proteasome formation in vivo and in vitro. Other RP subcomplexes contain Hsm3, which is related to mammalian proteasome subunit S5b. Hsm3 also contributes to base assembly. Larger Hsm3-containing complexes include two additional proteins, Nas6 and Rpn14, which function as assembly chaperones as well. Specific deletion combinations affecting these four factors cause severe perturbations to RP assembly. Our results demonstrate that proteasomal RP biogenesis requires multiple, functionally overlapping chaperones and suggest a model in which subunits form specific subcomplexes that then assemble into the base.

CsI Calorimeter for a Compton-Pair Telescope

NASA Astrophysics Data System (ADS)

Grove, Eric J.

We propose to build and test a hodoscopic CsI(Tl) scintillating-crystal calorimeter for a medium-energy γ-ray Compton and pair telescope. The design and technical approach for this calorimeter relies deeply on heritage from the Fermi LAT CsI Calorimeter, but it dramatically improves the low-energy performance of that design by reading out the scintillation light with silicon photomultipliers (SiPMs), making the technology developed for Fermi applicable in the Compton regime. While such a hodoscopic calorimeter is useful for an entire class of medium-energy γ-ray telescope designs, we propose to build it explicitly to support beam tests and balloon flight of the Proto-ComPair telescope, the development and construction of which was funded in a four-year APRA program beginning in 2015 ("ComPair: Steps to a Medium Energy γ-ray Mission" with PI J. McEnery of GSFC). That award did not include funding for its CsI calorimeter subsystem, and this proposal is intended to cover that gap. ComPair is a MIDEX-class instrument concept to perform a high-sensitivity survey of the γ-ray sky from 0.5 MeV to 500 MeV. ComPair is designed to provide a dramatic increase in sensitivity relative to previous instruments in this energy range (predominantly INTEGRAL/SPI and Compton COMPTEL), with the same transformative sensitivity increase - and corresponding scientific return- that the Fermi Large Area Telescope provided relative to Compton EGRET. To enable transformative science over a broad range of MeV energies and with a wide field of view, ComPair is a combined Compton telescope and pair telescope employing a silicon-strip tracker (for Compton scattering and pair conversion and tracking) and a solid-state CdZnTe calorimeter (for Compton absorption) and CsI calorimeter (for pair calorimetry), surrounded by a plastic scintillator anti-coincidence detector. Under the current proposal, we will complete the detailed design, assembly, and test of the CsI calorimeter for the risk-reduction prototype telescope, Proto-ComPair. We will: 1. Purchase CsI(Tl) crystals, Silicon Photomultipliers (SiPMs), and components for the analog and digital readout of the SiPMs; 2. Assemble and test Crystal Detector Elements (CDEs) from crystals, SiPMs and optical wrap; 3. Assemble and test analog and digital front-end and readout control boards; 4. Fabricate the mechanical structure that supports and contains the CDEs and electronics boards; and 5. Assemble and test the CsI calorimeter, and integrate it with the remainder of the Proto-ComPair subsystems. The PI team for this proposal conceived, designed, developed, assembled, tested, and currently operates the LAT calorimeter and is uniquely qualified to leverage the experience gained from that effort for ComPair.

An Integrated Architecture for On-Board Aircraft Engine Performance Trend Monitoring and Gas Path Fault Diagnostics

NASA Technical Reports Server (NTRS)

Simon, Donald L.

2010-01-01

Aircraft engine performance trend monitoring and gas path fault diagnostics are closely related technologies that assist operators in managing the health of their gas turbine engine assets. Trend monitoring is the process of monitoring the gradual performance change that an aircraft engine will naturally incur over time due to turbomachinery deterioration, while gas path diagnostics is the process of detecting and isolating the occurrence of any faults impacting engine flow-path performance. Today, performance trend monitoring and gas path fault diagnostic functions are performed by a combination of on-board and off-board strategies. On-board engine control computers contain logic that monitors for anomalous engine operation in real-time. Off-board ground stations are used to conduct fleet-wide engine trend monitoring and fault diagnostics based on data collected from each engine each flight. Continuing advances in avionics are enabling the migration of portions of the ground-based functionality on-board, giving rise to more sophisticated on-board engine health management capabilities. This paper reviews the conventional engine performance trend monitoring and gas path fault diagnostic architecture commonly applied today, and presents a proposed enhanced on-board architecture for future applications. The enhanced architecture gains real-time access to an expanded quantity of engine parameters, and provides advanced on-board model-based estimation capabilities. The benefits of the enhanced architecture include the real-time continuous monitoring of engine health, the early diagnosis of fault conditions, and the estimation of unmeasured engine performance parameters. A future vision to advance the enhanced architecture is also presented and discussed

Physics-based process modeling, reliability prediction, and design guidelines for flip-chip devices

NASA Astrophysics Data System (ADS)

Michaelides, Stylianos

Flip Chip on Board (FCOB) and Chip-Scale Packages (CSPs) are relatively new technologies that are being increasingly used in the electronic packaging industry. Compared to the more widely used face-up wirebonding and TAB technologies, flip-chips and most CSPs provide the shortest possible leads, lower inductance, higher frequency, better noise control, higher density, greater input/output (I/O), smaller device footprint and lower profile. However, due to the short history and due to the introduction of several new electronic materials, designs, and processing conditions, very limited work has been done to understand the role of material, geometry, and processing parameters on the reliability of flip-chip devices. Also, with the ever-increasing complexity of semiconductor packages and with the continued reduction in time to market, it is too costly to wait until the later stages of design and testing to discover that the reliability is not satisfactory. The objective of the research is to develop integrated process-reliability models that will take into consideration the mechanics of assembly processes to be able to determine the reliability of face-down devices under thermal cycling and long-term temperature dwelling. The models incorporate the time and temperature-dependent constitutive behavior of various materials in the assembly to be able to predict failure modes such as die cracking and solder cracking. In addition, the models account for process-induced defects and macro-micro features of the assembly. Creep-fatigue and continuum-damage mechanics models for the solder interconnects and fracture-mechanics models for the die have been used to determine the reliability of the devices. The results predicted by the models have been successfully validated against experimental data. The validated models have been used to develop qualification and test procedures for implantable medical devices. In addition, the research has helped develop innovative face-down devices without the underfill, based on the thorough understanding of the failure modes. Also, practical design guidelines for material, geometry and process parameters for reliable flip-chip devices have been developed.

Harem: Hardwood lumber remanufacturing program for maxmizing value based on size, grade and current market prices

Treesearch

C.J. Schwehm; P. Klinkhachorn; Charles W. McMillin; Henry A. Huber

1990-01-01

This paper describes an expert system computer program which will determine the optimum way to edge and trim a hardwood board so as to yield the highest dollar value based on the grade, size of each board, and current market prices. The program uses the Automated Hardwood Lumber Grading Program written by Klinkhachorn, et al. for determining the grade of each board...

Assembly planning based on subassembly extraction

NASA Technical Reports Server (NTRS)

Lee, Sukhan; Shin, Yeong Gil

1990-01-01

A method is presented for the automatic determination of assembly partial orders from a liaison graph representation of an assembly through the extraction of preferred subassemblies. In particular, the authors show how to select a set of tentative subassemblies by decomposing a liaison graph into a set of subgraphs based on feasibility and difficulty of disassembly, how to evaluate each of the tentative subassemblies in terms of assembly cost using the subassembly selection indices, and how to construct a hierarchical partial order graph (HPOG) as an assembly plan. The method provides an approach to assembly planning by identifying spatial parallelism in assembly as a means of constructing temporal relationships among assembly operations and solves the problem of finding a cost-effective assembly plan in a flexible environment. A case study of the assembly planning of a mechanical assembly is presented.

Quality data collection and management technology of aerospace complex product assembly process

NASA Astrophysics Data System (ADS)

Weng, Gang; Liu, Jianhua; He, Yongxi; Zhuang, Cunbo

2017-04-01

Aiming at solving problems of difficult management and poor traceability for discrete assembly process quality data, a data collection and management method is proposed which take the assembly process and BOM as the core. Data collection method base on workflow technology, data model base on BOM and quality traceability of assembly process is included in the method. Finally, assembly process quality data management system is developed and effective control and management of quality information for complex product assembly process is realized.

Improvement of the Threespine Stickleback Genome Using a Hi-C-Based Proximity-Guided Assembly.

PubMed

Peichel, Catherine L; Sullivan, Shawn T; Liachko, Ivan; White, Michael A

2017-09-01

Scaffolding genomes into complete chromosome assemblies remains challenging even with the rapidly increasing sequence coverage generated by current next-generation sequence technologies. Even with scaffolding information, many genome assemblies remain incomplete. The genome of the threespine stickleback (Gasterosteus aculeatus), a fish model system in evolutionary genetics and genomics, is not completely assembled despite scaffolding with high-density linkage maps. Here, we first test the ability of a Hi-C based proximity-guided assembly (PGA) to perform a de novo genome assembly from relatively short contigs. Using Hi-C based PGA, we generated complete chromosome assemblies from a distribution of short contigs (20-100 kb). We found that 96.40% of contigs were correctly assigned to linkage groups (LGs), with ordering nearly identical to the previous genome assembly. Using available bacterial artificial chromosome (BAC) end sequences, we provide evidence that some of the few discrepancies between the Hi-C assembly and the existing assembly are due to structural variation between the populations used for the 2 assemblies or errors in the existing assembly. This Hi-C assembly also allowed us to improve the existing assembly, assigning over 60% (13.35 Mb) of the previously unassigned (~21.7 Mb) contigs to LGs. Together, our results highlight the potential of the Hi-C based PGA method to be used in combination with short read data to perform relatively inexpensive de novo genome assemblies. This approach will be particularly useful in organisms in which it is difficult to perform linkage mapping or to obtain high molecular weight DNA required for other scaffolding methods. © The American Genetic Association 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Hardwood lumber scanning tests to determine NHLA lumber grades

Treesearch

Philip A. Araman; Ssang-Mook Lee; A. Lynn Abbott; Matthew F. Winn

2011-01-01

This paper concerns the scanning, and grading of kiln-dried hardwood lumber. A prototype system is described that uses laser sources and a video camera to scan boards. The system automatically detects defects and wane, grades the boards, and then searches for higher value boards within the original board. The goal is to derive maximum commercial value based on current...

Hardware Architecture and Cutting-Edge Assembly Process of a Tiny Curved Compound Eye

PubMed Central

Viollet, Stéphane; Godiot, Stéphanie; Leitel, Robert; Buss, Wolfgang; Breugnon, Patrick; Menouni, Mohsine; Juston, Raphaël; Expert, Fabien; Colonnier, Fabien; L'Eplattenier, Géraud; Brückner, Andreas; Kraze, Felix; Mallot, Hanspeter; Franceschini, Nicolas; Pericet-Camara, Ramon; Ruffier, Franck; Floreano, Dario

2014-01-01

The demand for bendable sensors increases constantly in the challenging field of soft and micro-scale robotics. We present here, in more detail, the flexible, functional, insect-inspired curved artificial compound eye (CurvACE) that was previously introduced in the Proceedings of the National Academy of Sciences (PNAS, 2013). This cylindrically-bent sensor with a large panoramic field-of-view of 180° × 60° composed of 630 artificial ommatidia weighs only 1.75 g, is extremely compact and power-lean (0.9 W), while it achieves unique visual motion sensing performance (1950 frames per second) in a five-decade range of illuminance. In particular, this paper details the innovative Very Large Scale Integration (VLSI) sensing layout, the accurate assembly fabrication process, the innovative, new fast read-out interface, as well as the auto-adaptive dynamic response of the CurvACE sensor. Starting from photodetectors and microoptics on wafer substrates and flexible printed circuit board, the complete assembly of CurvACE was performed in a planar configuration, ensuring high alignment accuracy and compatibility with state-of-the art assembling processes. The characteristics of the photodetector of one artificial ommatidium have been assessed in terms of their dynamic response to light steps. We also characterized the local auto-adaptability of CurvACE photodetectors in response to large illuminance changes: this feature will certainly be of great interest for future applications in real indoor and outdoor environments. PMID:25407908

DYNAMICS OF ON-DISK PLUMES AS OBSERVED WITH THE INTERFACE REGION IMAGING SPECTROGRAPH, THE ATMOSPHERIC IMAGING ASSEMBLY, AND THE HELIOSEISMIC AND MAGNETIC IMAGER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pant, Vaibhav; Mazumder, Rakesh; Banerjee, Dipankar

2015-07-01

We examine the role of small-scale transients in the formation and evolution of solar coronal plumes. We study the dynamics of plume footpoints seen in the vicinity of a coronal hole using the Atmospheric Imaging Assembly (AIA) images, the Helioseismic and Magnetic Imager magnetogram on board the Solar Dynamics Observatory and spectroscopic data from the Interface Region Imaging Spectrograph (IRIS). Quasi-periodic brightenings are observed in the base of the plumes and are associated with magnetic flux changes. With the high spectral and spatial resolution of IRIS, we identify the sources of these oscillations and try to understand what role themore » transients at the footpoints can play in sustaining the coronal plumes. IRIS “sit-and-stare” observations provide a unique opportunity to study the evolution of footpoints of the plumes. We notice enhanced line width and intensity, and large deviation from the average Doppler shift in the line profiles at specific instances, which indicate the presence of flows at the footpoints of plumes. We propose that outflows (jet-like features) as a result of small-scale reconnections affect the line profiles. These jet-like features may also be responsible for the generation of propagating disturbances (PDs) within the plumes, which are observed to be propagating to larger distances as recorded from multiple AIA channels. These PDs can be explained in terms of slow magnetoacoustic waves.« less

Performance and characterization of new micromachined high-frequency linear arrays.

PubMed

Lukacs, Marc; Yin, Jianhua; Pang, Guofeng; Garcia, Richard C; Cherin, Emmanuel; Williams, Ross; Mehi, Jim; Foster, F Stuart

2006-10-01

A new approach for fabricating high frequency (> 20 MHz) linear array transducers, based on laser micromachining, has been developed. A 30 MHz, 64-element, 74-microm pitch, linear array design is presented. The performance of the device is demonstrated by comparing electrical and acoustic measurements with analytical, equivalent circuit, and finite-element analysis (FEA) simulations. All FEA results for array performance have been generated using one global set of material parameters. Each fabricated array has been integrated onto a flex circuit for ease of handling, and the flex has been integrated onto a custom printed circuit board test card for ease of testing. For a fully assembled array, with an acoustic lens, the center frequency was 28.7 MHz with a one-way -3 dB and -6 dB bandwidth of 59% and 83%, respectively, and a -20 dB pulse width of -99 ns. The per-element peak acoustic power, for a +/- 30 V single cycle pulse, measured at the 10 mm focal length of the lens was 590 kPa with a -6 dB directivity span of about 30 degrees. The worst-case total cross talk of the combined array and flex assembly is for nearest neighboring elements and was measured to have an average level -40 dB across the -6 dB bandwidth of the device. Any significant deviation from simulation can be explained through limitations in apparatus calibration and in device packaging.

Waveguide electro-optic modulators based on intrinsically polar self-assembled superlattices (SASs)

NASA Astrophysics Data System (ADS)

Liu, Zhifu; Ho, Seng Tiong; Chang, Seongsik; Zhao, Yiguang; Marks, Tobin J.; Kang, Hu; van der Boom, Milko E.; Zhu, Peiwang

2002-12-01

In this paper we describe methods of fabricating and characterizing organic electro-optic modulators based on intrinsically polar self-assembled superlattices. These structures are intrinsically acentric, and exhibit large second harmonic generation and electro-optic responses without the requirement of poling by an external electric field. A novel wet chemical protection-deprotection approach for the growth of self-assembled superlattices have been developed, and the refractive indices of self-assembled organic electro-optic superlattices may be tuned during the self-assembly process. Prototype electro-optic modulators based on chromophoric self-assembled superlattices have been designed and fabricated. The effective electro-optic coefficient of the self-assembled superlattice film in a phase modulator is estimated as about 20 pm/V at a wavelength of 1064 nm.

Hydro lazy tongs energy booster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamonica, M.

1987-06-09

An apparatus is described for converting hydraulic power to rotational power. The apparatus comprises: a support base; a source of hydraulic fluid; a pair of piston and cylinder assemblies in communication with the source of hydraulic fluid and mounted to the support base such that the pistons thereof are generally parallel with one another but extending substantially opposite directions; means for alternating directly hydraulic fluid to each of the piston and cylinder assemblies; lazy tong assemblies comprising a first lazy tong assembly, a last lazy tong assembly and an intermediate lazy tong assembly. Each lazy tong assembly comprises at leastmore » one block slidably mounted in proximity to the support base and at least one pair of lazy tongs with each lazy tong having a pair of opposed ends.« less

Space assembly fixtures and aids

NASA Technical Reports Server (NTRS)

Bloom, K. A.; Lillenas, A. N.

1980-01-01

Concepts and requirements for assembly fixtures and aids necessary for the assembly and maintenance of spare platforms were studied. Emphasis was placed on erectable and deployable type structures with the shuttle orbiter as the assembly base. Both single and multiple orbiter flight cases for the platform assembly were considered. Applicable space platform assembly studies were reviewed to provide a data base for establishing the assembly fixture and aids design requirements, assembly constraints, and the development of representative design concepts. Conclusions indicated that fixture requirements will vary with platform size. Larger platforms will require translation relative to the orbiter RMS working volume. The installation of platform payloads and subsystems (e.g., utility distribution) must also be considered in the specification of assembly fixtures and aids.

Master dye laser oscillator including a specific grating assembly for use therein

DOEpatents

Davin, James M.

1992-01-01

A dye laser oscillator for producing a tuned dye beam is disclosed herein and includes, among other components, a beam output coupling assembly, a dye cell assembly, a beam expander assembly, an etalon assembly, and a grating assembly. Each of three assemblies is vertically supported from a horizontal base so as to be readily removable from the base without interference from or interfering with the other assemblies. The particular grating assembly disclosed is specifically designed for proper optical alignment with the intended path of the dye beam to be produced and for accurate pivotal movement relative to the beam path in order to function as a coarse tuning mechanism in the production of the ultimately tuned beam.

Master dye laser oscillator including a specific grating assembly for use therein

DOEpatents

Davin, J.M.

1992-09-01

A dye laser oscillator for producing a tuned dye beam is disclosed herein and includes, among other components, a beam output coupling assembly, a dye cell assembly, a beam expander assembly, an etalon assembly, and a grating assembly. Each of three assemblies is vertically supported from a horizontal base so as to be readily removable from the base without interference from or interfering with the other assemblies. The particular grating assembly disclosed is specifically designed for proper optical alignment with the intended path of the dye beam to be produced and for accurate pivotal movement relative to the beam path in order to function as a coarse tuning mechanism in the production of the ultimately tuned beam. 5 figs.

An empirical comparison between the board's strategic role in nonprofit hospitals and in for-profit industrial firms.

PubMed Central

Judge, W Q; Zeithaml, C P

1992-01-01

As the health care environment becomes more competitive, nonprofit hospitals are under pressure to adopt for-profit business practices. Based on an extensive field study, this research examines the central issue of organizational governance by comparing the strategic roles of nonprofit hospital boards with for-profit industrial boards. The results show that nonprofit hospital boards are generally more involved in the strategic decision process than their for-profit counterparts. If this governance activity is seen as desirable, hospital boards should exercise caution in emulating for-profit board practices. PMID:1563953

Enhanced Weather Radar (EWxR) System

NASA Technical Reports Server (NTRS)

Kronfeld, Kevin M. (Technical Monitor)

2003-01-01

An airborne weather radar system, the Enhanced Weather Radar (EWxR), with enhanced on-board weather radar data processing was developed and tested. The system features additional weather data that is uplinked from ground-based sources, specialized data processing, and limited automatic radar control to search for hazardous weather. National Weather Service (NWS) ground-based Next Generation Radar (NEXRAD) information is used by the EWxR system to augment the on-board weather radar information. The system will simultaneously display NEXRAD and on-board weather radar information in a split-view format. The on-board weather radar includes an automated or hands-free storm-finding feature that optimizes the radar returns by automatically adjusting the tilt and range settings for the current altitude above the terrain and searches for storm cells near the atmospheric 0-degree isotherm. A rule-based decision aid was developed to automatically characterize cells as hazardous, possibly-hazardous, or non-hazardous based upon attributes of that cell. Cell attributes are determined based on data from the on-board radar and from ground-based radars. A flight path impact prediction algorithm was developed to help pilots to avoid hazardous weather along their flight plan and their mission. During development the system was tested on the NASA B757 aircraft and final tests were conducted on the Rockwell Collins Sabreliner.

Advanced membrane electrode assemblies for fuel cells

DOEpatents

Kim, Yu Seung; Pivovar, Bryan S.

2012-07-24

A method of preparing advanced membrane electrode assemblies (MEA) for use in fuel cells. A base polymer is selected for a base membrane. An electrode composition is selected to optimize properties exhibited by the membrane electrode assembly based on the selection of the base polymer. A property-tuning coating layer composition is selected based on compatibility with the base polymer and the electrode composition. A solvent is selected based on the interaction of the solvent with the base polymer and the property-tuning coating layer composition. The MEA is assembled by preparing the base membrane and then applying the property-tuning coating layer to form a composite membrane. Finally, a catalyst is applied to the composite membrane.

Advanced membrane electrode assemblies for fuel cells

DOEpatents

Kim, Yu Seung; Pivovar, Bryan S

2014-02-25

A method of preparing advanced membrane electrode assemblies (MEA) for use in fuel cells. A base polymer is selected for a base membrane. An electrode composition is selected to optimize properties exhibited by the membrane electrode assembly based on the selection of the base polymer. A property-tuning coating layer composition is selected based on compatibility with the base polymer and the electrode composition. A solvent is selected based on the interaction of the solvent with the base polymer and the property-tuning coating layer composition. The MEA is assembled by preparing the base membrane and then applying the property-tuning coating layer to form a composite membrane. Finally, a catalyst is applied to the composite membrane.

Spacecube: A Family of Reconfigurable Hybrid On-Board Science Data Processors

NASA Technical Reports Server (NTRS)

Flatley, Thomas P.

2015-01-01

SpaceCube is a family of Field Programmable Gate Array (FPGA) based on-board science data processing systems developed at the NASA Goddard Space Flight Center (GSFC). The goal of the SpaceCube program is to provide 10x to 100x improvements in on-board computing power while lowering relative power consumption and cost. SpaceCube is based on the Xilinx Virtex family of FPGAs, which include processor, FPGA logic and digital signal processing (DSP) resources. These processing elements are leveraged to produce a hybrid science data processing platform that accelerates the execution of algorithms by distributing computational functions to the most suitable elements. This approach enables the implementation of complex on-board functions that were previously limited to ground based systems, such as on-board product generation, data reduction, calibration, classification, eventfeature detection, data mining and real-time autonomous operations. The system is fully reconfigurable in flight, including data parameters, software and FPGA logic, through either ground commanding or autonomously in response to detected eventsfeatures in the instrument data stream.

Enabling nurses to lead change: The orientation experiences of nurses to boards

PubMed Central

Walton, AnnMarie; Lake, Donna; Mullinix, Connie; Allen, Deborah; Mooney, Kathi

2015-01-01

Objectives Nurses need to be full partners in shaping health care and health care policy. One way to do this is to be present and active on boards at all levels. The purpose of this study is to examine the orientation experiences of nurses to boards and their preparation to influence health care and health care policy. Methods A Web-based survey about the efficacy of board orientation was sent to members of three local boards made up exclusively of nurses. Results Liabilities and fiduciary duties were least likely to be addressed in board orientation for nurses. Board members requested more training in finance and a more formal/structured orientation process. Conclusions Standardizing orientation elements for nurses serving on boards would best prepare them to serve on interprofessional hospital boards and work in the health policy arena. The orientation experience on local- and state-level nursing boards is fundamental to nurses beginning board service. PMID:25771188

Enabling nurses to lead change: the orientation experiences of nurses to boards.

PubMed

Walton, AnnMarie; Lake, Donna; Mullinix, Connie; Allen, Deborah; Mooney, Kathi

2015-01-01

Nurses need to be full partners in shaping health care and health care policy. One way to do this is to be present and active on boards at all levels. The purpose of this study is to examine the orientation experiences of nurses to boards and their preparation to influence health care and health care policy. A Web-based survey about the efficacy of board orientation was sent to members of three local boards made up exclusively of nurses. Liabilities and fiduciary duties were least likely to be addressed in board orientation for nurses. Board members requested more training in finance and a more formal/structured orientation process. Standardizing orientation elements for nurses serving on boards would best prepare them to serve on interprofessional hospital boards and work in the health policy arena. The orientation experience on local- and state-level nursing boards is fundamental to nurses beginning board service. Copyright © 2015 Elsevier Inc. All rights reserved.

Applications of Emerging Parallel Optical Link Technology to High Energy Physics Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chramowicz, J.; Kwan, S.; Prosser, A.

2011-09-01

Modern particle detectors depend upon optical fiber links to deliver event data to upstream trigger and data processing systems. Future detector systems can benefit from the development of dense arrangements of high speed optical links emerging from the telecommunications and storage area network market segments. These links support data transfers in each direction at rates up to 120 Gbps in packages that minimize or even eliminate edge connector requirements. Emerging products include a class of devices known as optical engines which permit assembly of the optical transceivers in close proximity to the electrical interfaces of ASICs and FPGAs which handlemore » the data in parallel electrical format. Such assemblies will reduce required printed circuit board area and minimize electromagnetic interference and susceptibility. We will present test results of some of these parallel components and report on the development of pluggable FPGA Mezzanine Cards equipped with optical engines to provide to collaborators on the Versatile Link Common Project for the HI-LHC at CERN.« less

Fast gradient-based algorithm on extended landscapes for wave-front reconstruction of Earth observation satellite

NASA Astrophysics Data System (ADS)

Thiebaut, C.; Perraud, L.; Delvit, J. M.; Latry, C.

2016-07-01

We present an on-board satellite implementation of a gradient-based (optical flows) algorithm for the shifts estimation between images of a Shack-Hartmann wave-front sensor on extended landscapes. The proposed algorithm has low complexity in comparison with classical correlation methods which is a big advantage for being used on-board a satellite at high instrument data rate and in real-time. The electronic board used for this implementation is designed for space applications and is composed of radiation-hardened software and hardware. Processing times of both shift estimations and pre-processing steps are compatible of on-board real-time computation.

Development of land based radar polarimeter processor system

NASA Technical Reports Server (NTRS)

Kronke, C. W.; Blanchard, A. J.

1983-01-01

The processing subsystem of a land based radar polarimeter was designed and constructed. This subsystem is labeled the remote data acquisition and distribution system (RDADS). The radar polarimeter, an experimental remote sensor, incorporates the RDADS to control all operations of the sensor. The RDADS uses industrial standard components including an 8-bit microprocessor based single board computer, analog input/output boards, a dynamic random access memory board, and power supplis. A high-speed digital electronics board was specially designed and constructed to control range-gating for the radar. A complete system of software programs was developed to operate the RDADS. The software uses a powerful real time, multi-tasking, executive package as an operating system. The hardware and software used in the RDADS are detailed. Future system improvements are recommended.

Highly-Parallel, Highly-Compact Computing Structures Implemented in Nanotechnology

NASA Technical Reports Server (NTRS)

Crawley, D. G.; Duff, M. J. B.; Fountain, T. J.; Moffat, C. D.; Tomlinson, C. D.

1995-01-01

In this paper, we describe work in which we are evaluating how the evolving properties of nano-electronic devices could best be utilized in highly parallel computing structures. Because of their combination of high performance, low power, and extreme compactness, such structures would have obvious applications in spaceborne environments, both for general mission control and for on-board data analysis. However, the anticipated properties of nano-devices mean that the optimum architecture for such systems is by no means certain. Candidates include single instruction multiple datastream (SIMD) arrays, neural networks, and multiple instruction multiple datastream (MIMD) assemblies.

Video File - NASA Conducts 2nd RS-25 Engine Hot Fire of 2018 - 2018-02-01

NASA Image and Video Library

2018-02-01

NASA Conducts 2nd RS-25 Engine Hot Fire of 2018. A 365-second hot fire test on Feb. 1, 2018, at NASA’s Stennis Space Center in Mississippi marks the completion of “green run” testing, or flight certification, for all new RS-25 engine flight controllers slated for Exploration Mission-2, the first Space Launch System mission with astronauts on board. In addition to the flight controller, the Feb. 1 hot fire also marked the third test of a 3D printed pogo accumulator assembly for the RS-25 engine.

KSC-08pd3185

NASA Image and Video Library

2008-10-14

CAPE CANAVERAL, Fla. – The deep-red sunset sky puts Launch pad 39A in silhouette. Space shuttle Atlantis is on the pad. Atlantis’ October target launch date for the STS-125 Hubble Space Telescope servicing mission was delayed after a device on board Hubble used in the storage and transmission of science data to Earth shut down on Sept. 27. Replacing the broken device will be added to Atlantis’ servicing mission to the telescope. In the interim, Atlantis will be rolled back to the Vehicle Assembly Building until a new target launch date can be set for the mission in 2009. Photo credit: NASA/Troy Cryder

Automation and robotics - Key to productivity. [in industry and space

NASA Technical Reports Server (NTRS)

Cohen, A.

1985-01-01

The automated and robotic systems requirements of the NASA Space Station are prompted by maintenance, repair, servicing and assembly requirements. Trend analyses, fault diagnoses, and subsystem status assessments for the Station's electrical power, guidance, navigation, control, data management and environmental control subsystems will be undertaken by cybernetic expert systems; this will reduce or eliminate on-board or ground facility activities that would otherwise be essential, enhancing system productivity. Additional capabilities may also be obtained through the incorporation of even a limited amount of artificial intelligence in the controllers of the various Space Station systems.

TSS-1R Failure Mode Evaluation

NASA Technical Reports Server (NTRS)

Vaughn, Jason A.; McCollum, Matthew B.; Kamenetzky, Rachel R.

1997-01-01

Soon after the break of the tether during the Tethered Satellite System (TSS-1R) mission in February, 1996, a Tiger Team was assembled at the George C. Marshall Space Flight Center to determine the tether failure mode. One possible failure scenario was the Kevlar' strength member of the tether failed because of degradation due to electrical discharge or electrical arcing. During the next several weeks, extensive electrical discharge testing in low vacuum and plasma environments was conducted in an attempt to reproduce the electrical activity recorded by on-board science instruments during the mission. The results of these tests are presented in this paper.

Compact fluid cooled power converter supporting multiple circuit boards

DOEpatents

Radosevich, Lawrence D.; Meyer, Andreas A.; Beihoff, Bruce C.; Kannenberg, Daniel G.

2005-03-08

A support may receive one or more power electronic circuits. The support may aid in removing heat from the circuits through fluid circulating through the support. The support, in conjunction with other packaging features may form a shield from both external EMI/RFI and from interference generated by operation of the power electronic circuits. Features may be provided to permit and enhance connection of the circuitry to external circuitry, such as improved terminal configurations. Modular units may be assembled that may be coupled to electronic circuitry via plug-in arrangements or through interface with a backplane or similar mounting and interconnecting structures.

On-Board Mining in the Sensor Web

NASA Astrophysics Data System (ADS)

Tanner, S.; Conover, H.; Graves, S.; Ramachandran, R.; Rushing, J.

2004-12-01

On-board data mining can contribute to many research and engineering applications, including natural hazard detection and prediction, intelligent sensor control, and the generation of customized data products for direct distribution to users. The ability to mine sensor data in real time can also be a critical component of autonomous operations, supporting deep space missions, unmanned aerial and ground-based vehicles (UAVs, UGVs), and a wide range of sensor meshes, webs and grids. On-board processing is expected to play a significant role in the next generation of NASA, Homeland Security, Department of Defense and civilian programs, providing for greater flexibility and versatility in measurements of physical systems. In addition, the use of UAV and UGV systems is increasing in military, emergency response and industrial applications. As research into the autonomy of these vehicles progresses, especially in fleet or web configurations, the applicability of on-board data mining is expected to increase significantly. Data mining in real time on board sensor platforms presents unique challenges. Most notably, the data to be mined is a continuous stream, rather than a fixed store such as a database. This means that the data mining algorithms must be modified to make only a single pass through the data. In addition, the on-board environment requires real time processing with limited computing resources, thus the algorithms must use fixed and relatively small amounts of processing time and memory. The University of Alabama in Huntsville is developing an innovative processing framework for the on-board data and information environment. The Environment for On-Board Processing (EVE) and the Adaptive On-board Data Processing (AODP) projects serve as proofs-of-concept of advanced information systems for remote sensing platforms. The EVE real-time processing infrastructure will upload, schedule and control the execution of processing plans on board remote sensors. These plans provide capabilities for autonomous data mining, classification and feature extraction using both streaming and buffered data sources. A ground-based testbed provides a heterogeneous, embedded hardware and software environment representing both space-based and ground-based sensor platforms, including wireless sensor mesh architectures. The AODP project explores the EVE concepts in the world of sensor-networks, including ad-hoc networks of small sensor platforms.

Institutional review board challenges related to community-based participatory research on human exposure to environmental toxins: A case study

PubMed Central

2010-01-01

Background We report on the challenges of obtaining Institutional Review Board (IRB) coverage for a community-based participatory research (CBPR) environmental justice project, which involved reporting biomonitoring and household exposure results to participants, and included lay participation in research. Methods We draw on our experiences guiding a multi-partner CBPR project through university and state Institutional Review Board reviews, and other CBPR colleagues' written accounts and conference presentations and discussions. We also interviewed academics involved in CBPR to learn of their challenges with Institutional Review Boards. Results We found that Institutional Review Boards are generally unfamiliar with CBPR, reluctant to oversee community partners, and resistant to ongoing researcher-participant interaction. Institutional Review Boards sometimes unintentionally violate the very principles of beneficence and justice which they are supposed to uphold. For example, some Institutional Review Boards refuse to allow report-back of individual data to participants, which contradicts the CBPR principles that guide a growing number of projects. This causes significant delays and may divert research and dissemination efforts. Our extensive education of our university Institutional Review Board convinced them to provide human subjects protection coverage for two community-based organizations in our partnership. Conclusions IRBs and funders should develop clear, routine review guidelines that respect the unique qualities of CBPR, while researchers and community partners can educate IRB staff and board members about the objectives, ethical frameworks, and research methods of CBPR. These strategies can better protect research participants from the harm of unnecessary delays and exclusion from the research process, while facilitating the ethical communication of study results to participants and communities. PMID:20637068

The Consensus Process at the Water Science and Technology Board, National Research Council

NASA Astrophysics Data System (ADS)

Logan, W. S.

2001-12-01

Whereas the very birth of the U.S. Geological Survey arose from the recommendations of a National Academy of Sciences report, water science has not always had a prominent place at that institution. Prior to the 1980s, water issues were dealt with on an ad hoc basis by various boards related to science, engineering, and policy. With the birth of the Water Science and Technology Board (WSTB) in 1982, a diversity of water-related issues are now handled under one roof. The "business" of the WSTB is to produce consensus reports on a spectrum of topics in water science. Some of the projects that the WSTB works on are self-generated. The majority are generated either by Congress, or by government agencies. The WSTB takes on several different kinds of studies. Some of these are designed to advance the science of hydrology itself. This category would include the report Opportunities in the Hydrologic Sciences, which helped to establish hydrologic science as something separate from applied hydrology in Congress, the White House, and agencies such as NSF. However, the majority of the board's consensus studies involve hydrology in the interests of improving the natural and human environment. For example, Water for the Future: The West Bank and Gaza Strip, Israel, and Jordan outlined consensus principles backed by scientists from all of these entities for sustaining freshwater resources of the region. Closer to home, but no less controversial, a WSTB committee recently reached consensus on improving the process by which states determine which water bodies are polluted enough to require clean-up, and develop Total Maximum Daily Loads for these pollutants. Another committee recently sorted through the scientific bases for using natural attenuation for various contaminants in ground water and soil. And an ongoing committee is trying to help the South Florida scientific community to determine the best strategies for restoring the Everglades to some semblance of its former self, while continuing to provide drinking and irrigation water and flood control. The committees and panels that we assemble meet over a period of months to years, and struggle to reach consensus on topics that by their very nature are problematical or controversial. Generally they succeed, by virtue of good will, strong leadership, and a well-defined statement of task.

Test module development to detect the flase call probe pins on microeprocessor test equipment

NASA Astrophysics Data System (ADS)

Tang, L. W.; Ong, N. R.; Mohamad, I. S. B.; Alcain, J. B.; Retnasamy, V.

2017-09-01

Probe pins are useful for electrical testing of microelectronic components, printed circuit board assembly (PCBA), microprocessors and other electronic devices due to it provides the conductivity test based on specific device circuit design. During the repeatable test runs, the load of test modules, contact failures and the current conductivity induces layer wear off all the tip of probe pins contact. Contamination will be build-up on probe pins and increased contact resistivity which results of cost loss and time loss for rectifying programs, rectifying testers and exchanging new probe pins. In this study, a resistivity approach will be developed to provide "Testing of Test Probes". The test module based on "Four-wire Ohm measurement" method with two alternative ways of applying power supply, that are 9V from a single power supply and 5V from Arduino UNO power supply were demonstrated to measure the small resistance value of microprocessor probe pin. A microcontroller with VEE Pro software was used to record the measurement data. The accuracy of both test modules were calibrated under different temperature conditions and result shows that 9V from a single power supply test module has higher measurement accuracy.

Low-cost embedded systems for democratizing ocean sensor technology in the coastal zone

NASA Astrophysics Data System (ADS)

Glazer, B. T.; Lio, H. I.

2017-12-01

Environmental sciences suffer from undersampling. Enabling sustained and unattended data collection in the coastal zone typically involves expensive instrumentation and infrastructure deployed as cabled observatories or moorings with little flexibility in deployment location following initial installation. High costs of commercially-available or custom instruments have limited the number of sensor sites that can be targeted by academic researchers, and have also limited engagement with the public. We have developed a novel, low-cost, open-source sensor and software platform to enable wireless data transfer of biogeochemical sensors in the coastal zone. The platform is centered upon widely available, low-cost, single board computers and microcontrollers. We have used a blend of on-hand research-grade sensors and low-cost open-source electronics that can be assembled by tech-savvy non-engineers. Robust, open-source code that remains customizable for specific miniNode configurations can match a specific site's measurement needs, depending on the scientific research priorities. We have demonstrated prototype capabilities and versatility through lab testing and field deployments of multiple sensor nodes with multiple sensor inputs, all of which are streaming near-real-time data from Kaneohe Bay over wireless RF links to a shore-based base station.

Assembling a biogenic hydrocarbon emissions inventory for the SCOS97-NARSTO modeling domain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin, M.T.; Winer, A.M.; Karlik, J.

1998-12-31

To assist in developing ozone control strategies for Southern California, the California Air Resources Board is developing a biogenic hydrocarbon (BHC) emissions inventory model for the SCOS97-NARSTO domain. The basis for this bottom-up model is SCOS97-NARSTO-specific landuse and landcover maps, leafmass constants, and BHC emission rates. In urban areas, landuse maps developed by the Southern California Association of Governments, San Diego Association of Governments, and other local governments are used while in natural areas, landcover and plant community databases produced by the GAP Analysis Project (GAP) are employed. Plant identities and canopy volumes for species in each landuse and landcovermore » category are based on the most recent botanical field survey data. Where possible, experimentally determined leafmass constant and BHC emission rate measurements reported in the literature are used or, for those species where experimental data are not available, values are assigned based on taxonomic methods. A geographic information system is being used to integrate these databases, as well as the most recent environmental correction algorithms and canopy shading factors, to produce a spatially- and temporally-resolved BHC emission inventory suitable for input into the Urban Airshed Model.« less

Evaluation of Brine Processing Technologies for Spacecraft Wastewater

NASA Technical Reports Server (NTRS)

Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie;

78 FR 65006 - National Space-Based Positioning, Navigation, and Timing (PNT) Advisory Board; Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-30

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice 13-125] National Space-Based Positioning, Navigation, and Timing (PNT) Advisory Board; Meeting AGENCY: National Aeronautics and Space Administration..., Public Law 92-463, as amended, and the President's 2004 U.S. Space-Based Positioning, Navigation, and...

The Sentinel-4 UVN focal plane assemblies

NASA Astrophysics Data System (ADS)

Hinger, Jürgen; Hohn, Rüdiger; Gebhardt, Eyk; Reichardt, Jörg

2017-09-01

The Sentinel-4 UVN Instrument is a dispersive imaging spectrometer covering the UV-VIS and the NIR wavelength. It is developed and built under an ESA contract by an industrial consortium led by Airbus Defence and Space. It will be accommodated on board of the MTG-S (Meteosat Third Generation - Sounder) satellite that will be placed in a geostationary orbit over Europe sampling data for generating two-dimensional maps of a number of atmospheric trace gases. The incoming light is dispersed by reflective gratings and detected by the two (UVVIS and NIR) CCDs mounted inside the focal plane assemblies. Both CCD detectors acquire spectral channels and spatial sampling in two orthogonal directions and will be operated at about 215 K mainly to minimize random telegraph signal effects and to reduce dark current. Stringent detector temperature as well as alignment stability requirements of less than +/-0.1 K per day respectively of less than 2 micrometers/2 arcseconds from ground to orbit are driving the FPA thermo-mechanical design. A specific FPA design feature is the redundant LED-calibration system for bad pixel detection as well as pixel gain and linearity monitoring. This paper reports on the design and qualification of the Focal Plane Assemblies with emphasis on thermo-mechanical as well as alignment stability verification.

Multi-position photovoltaic assembly

DOEpatents

Dinwoodie, Thomas L.

2003-03-18

The invention is directed to a PV assembly, for use on a support surface, comprising a base, a PV module, a multi-position module support assembly, securing the module to the base at shipping and inclined-use angles, a deflector, a multi-position deflector support securing the deflector to the base at deflector shipping and deflector inclined-use angles, the module and deflector having opposed edges defining a gap therebetween. The invention permits transport of the PV assemblies in a relatively compact form, thus lowering shipping costs, while facilitating installation of the PV assemblies with the PV module at the proper inclination.

Cellulose nanofiber board.

PubMed

Yousefi, Hossein; Azad, Sona; Mashkour, Mahdi; Khazaeian, Abolghasem

2018-05-01

A cellulose nanofiber board (CNF-board) with a nominal thickness of 3 mm was fabricated without adhesive or additive. To provide comparison, a cellulose fiber board (CF-board) was also fabricated. A novel cold pre-press apparatus was made to dewater highly absorbent CNF gel prior to drying. A mild drying condition in the vacuum oven at 70 °C and 0.005 MPa was enough to provide the CNF-board with a density of 1.3 g/cm 3 thanks to its self-densification capability. Unlike the CF-board, the fabricated CNF-board had a high water-activated dimensional recovery ratio (averagely 96%) during the five cyclic wetting-drying process. The flexural and tensile strengths of CNF-board obtained were 162 MPa and 85 MPa, respectively. The corresponding values for CF-board were 28 MPa and 11 MPa, respectively. The specific flexural and tensile strengths of CNF-board obtained were higher than those of CF-board as well as some other traditional wood-based composites, polymers and structural ASTM A36 steel. Copyright © 2018 Elsevier Ltd. All rights reserved.

Induced-Dipole-Directed, Cooperative Self-Assembly of a Benzotrithiophene.

PubMed

Ikeda, Toshiaki; Adachi, Hiroaki; Fueno, Hiroyuki; Tanaka, Kazuyoshi; Haino, Takeharu

2017-10-06

A benzotrithiophene derivative possessing phenylisoxazoles self-assembled to form stacks. The molecule isodesmically self-assembled in chloroform, whereas it self-assembled in a cooperative fashion in decalin and in methylcyclohexane. Thermodynamic studies based on isodesmic, van der Schoot, and Goldstein-Stryer mathematical models revealed that the self-assembly processes are enthalpically driven and entropically opposed. An enthalpy-entropy compensation plot indicates that the assembly processes in chloroform, decalin, and methylcyclohexane are closely related. The enthalpic gains in less-polar solvents are greater than those in more-polar solvents, resulting in the formation of large assemblies in decalin and in methylcyclohexane. The formation of large assemblies leads to cooperative assemblies. The elongation process is enthalpically more favored than the nucleation process, which drives the cooperativity of the self-assembly. DFT calculations suggested that a hexameric assembly is more stable than tetrameric or dimeric assemblies. Cooperative self-assemblies based on intermolecular interactions other than hydrogen bonding have rarely been reported. It is demonstrated herein that van der Waals interactions, including induced dipole-dipole interactions, can drive the cooperative assembly of planar π-conjugated molecules.

An exploratory study of alternative configurations of governing boards of substance abuse treatment centers

PubMed Central

Blum, Terry C.; Roman, Paul M.

2011-01-01

Boards of directors are the ultimate governing authorities for most organizations providing substance abuse treatment. A governing board may establish policies, monitor and improve operations, and represent a treatment organization to the public. This paper explores alternative configurations of governing boards in a national sample of 500 substance abuse treatment centers. The study proceeds from the premise that boards may be configured with varying levels of engagement in five aspects of internal management and external connections in treatment center operating environments. Based on interviews with treatment center administrative directors, four clusters emerge, describing boards that are: (1) active and balanced across internal and external domains; (2) active boundary spanners concentrating primarily on external relationships; (3) focused primarily on internal organizational management; and (4) relatively inactive. In post hoc analysis, we found that placement in these clusters is associated with treatment center attributes such as rate of growth and financial results, use of evidence based practices and provision of integrated care. PMID:21489737

Evaluation of Binding Effects in Wood Flour Board Containing Ligno-Cellulose Nanofibers

PubMed Central

Kojima, Yoichi; Isa, Akiko; Kobori, Hikaru; Suzuki, Shigehiko; Ito, Hirokazu; Makise, Rie; Okamoto, Masaki

2014-01-01

Wood-based materials are used extensively in residual construction worldwide. Most of the adhesives used in wood-based materials are derived from fossil resources, and some are not environmentally friendly. This study explores nanofiber technology as an alternative to such adhesives. Previous studies have shown that the three-dimensional binding effects of cellulose nanofiber (CNF), when mixed with wood flour, can significantly improve the physical and mechanical properties of wood flour board. In this study, ligno-cellulose nanofibers (LCNF) were fabricated by wet disk milling of wood flour. Composite boards of wood flour and LCNF were produced to investigate the binding effect(s) of LCNF. The fabrication of LCNF by disk milling was simple and effective, and its incorporation into wood flour board significantly enhanced the physical and mechanical properties of the board. PMID:28788217

American Board of Orthodontics: Time for change.

PubMed

Chung, Chun-Hsi; Tadlock, Larry P; Barone, Nicholas; Pangrazio-Kulbersh, Valmy; Sabott, David G; Foley, Patrick F; Trulove, Timothy S; Park, Jae Hyun; Dugoni, Steven A

2018-03-01

The American Board of Orthodontics (ABO) works to certify orthodontists in a fair, reliable, and valid manner. The process must examine an orthodontist's knowledge, abilities, and critical thinking skills to ensure that each certified orthodontist has the expertise to provide the highest level of patient care. Many medical specialty boards and 4 American Dental Association specialty boards use scenario-based testing for board certification. Changing to a scenario-based clinical examination will allow the ABO to test more orthodontists. The new process will not result in an easier examination; standards will not be lowered. It will offer an improved testing method that will be fair, valid, and reliable for the specialty of orthodontics while increasing accessibility and complementing residency curricula. The ABO's written examination will remain as it is. Copyright © 2018 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

34. SOUTHWEST CORNER OF BUILDING 233 (MISSILE ASSEMBLY SHOP) IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. SOUTHWEST CORNER OF BUILDING 233 (MISSILE ASSEMBLY SHOP) IN ASSEMBLY AREA. - Loring Air Force Base, Weapons Storage Area, Northeastern corner of base at northern end of Maine Road, Limestone, Aroostook County, ME

Real-Time Probing of Nanowire Assembly Kinetics at the Air-Water Interface by In Situ Synchrotron X-Ray Scattering.

PubMed

He, Zhen; Jiang, Hui-Jun; Wu, Long-Long; Liu, Jian-Wei; Wang, Geng; Wang, Xiao; Wang, Jin-Long; Hou, Zhong-Huai; Chen, Gang; Yu, Shu-Hong

2018-07-02

Although many assembly strategies have been used to successfully construct well-aligned nanowire (NW) assemblies, the understanding of their assembly kinetics has remained elusive, which restricts the development of NW-based device and circuit fabrication. Now a versatile strategy that combines interfacial assembly and synchrotron-based grazing-incidence small-angle X-ray scattering (GISAXS) is presented to track the assembly evolution of the NWs in real time. During the interface assembly process, the randomly dispersed NWs gradually aggregate to form small ordered NW-blocks and finally are constructed into well-defined NW monolayer driven by the conformation entropy. The NW assembly mechanism can be well revealed by the thermodynamic analysis and large-scale molecular dynamics theoretical evaluation. These findings point to new opportunities for understanding NW assembly kinetics and manipulating NW assembled structures by bottom-up strategy. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Board task performance: An exploration of micro- and macro-level determinants of board effectiveness

PubMed Central

Minichilli, Alessandro; Zattoni, Alessandro; Nielsen, Sabina; Huse, Morten

2012-01-01

This paper addresses recent calls to narrow the micro–macro gap in management research (Bamberger, 2008), by incorporating a macro-level context variable (country) in exploring micro-level determinants of board effectiveness. Following the integrated model proposed by Forbes and Milliken (1999), we identify three board processes as micro-level determinants of board effectiveness. Specifically, we focus on effort norms, cognitive conflicts and the use of knowledge and skills as determinants of board control and advisory task performance. Further, we consider how two different institutional settings influence board tasks, and how the context moderates the relationship between processes and tasks. Our hypotheses are tested on a survey-based dataset of 535 medium-sized and large industrial firms in Italy and Norway, which are considered to substantially differ along legal and cultural dimensions. The findings show that: (i) Board processes have a larger potential than demographic variables to explain board task performance; (ii) board task performance differs significantly between boards operating in different contexts; and (iii) national context moderates the relationships between board processes and board task performance. Copyright © 2010 John Wiley & Sons, Ltd. PMID:23365485

12 CFR 652.60 - Corporation board guidelines.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Corporation board guidelines. 652.60 Section 652.60 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM FEDERAL AGRICULTURAL MORTGAGE CORPORATION FUNDING AND FISCAL AFFAIRS Risk-Based Capital Requirements § 652.60 Corporation board guidelines...

12 CFR 652.60 - Corporation board guidelines.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Corporation board guidelines. 652.60 Section 652.60 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM FEDERAL AGRICULTURAL MORTGAGE CORPORATION FUNDING AND FISCAL AFFAIRS Risk-Based Capital Requirements § 652.60 Corporation board guidelines...

12 CFR 652.60 - Corporation board guidelines.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Corporation board guidelines. 652.60 Section 652.60 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM FEDERAL AGRICULTURAL MORTGAGE CORPORATION FUNDING AND FISCAL AFFAIRS Risk-Based Capital Requirements § 652.60 Corporation board guidelines...

A Bibliography of Empirical Studies of School Boards, 1952-1968.

ERIC Educational Resources Information Center

Charters, W. W., Jr.

This bibliography lists 223 journal articles, unpublished master's and doctoral dissertations, bulletins, books, and monographs on the behavior, attributes, attitudes, or interaction of school board members. Included are reports of investigations that offer bases for generalizable propositions regarding the local school board's part in district…

Reliability of CCGA 1152 and CCGA 1272 Interconnect Packages for Extreme Thermal Environments

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni

2013-01-01

Ceramic column grid array (CCGA) packages have been increasing in use based on their advantages of high interconnect density, very good thermal and electrical performance, and compatibility with standard surface-mount packaging assembly processes. CCGA packages are used in space applications such as in logics and microprocessor functions, telecommunications, flight avionics, and payload electronics. As these packages tend to have less solder joint strain relief than leaded packages, the reliability of CCGA packages is very important for short- and long-term space missions. Certain planetary satellites require operations of thermally uncontrolled hardware under extremely cold and hot temperatures with large diurnal temperature change from day to night. The planetary protection requires the hardware to be baked at +125 C for 72 hours to kill microbugs to avoid any biological contamination, especially for sample return missions. Therefore, the present CCGA package reliability research study has encompassed the temperature range of 185 to +125 C to cover various NASA deep space missions. Advanced 1152 and 1272 CCGA packaging interconnects technology test hardware objects have been subjected to ex treme temperature thermal cycles from 185 to +125 C. X-ray inspections of CCGA packages have been made before thermal cycling. No anomalous behavior and process problems were observed in the x-ray images. The change in resistance of the daisy-chained CCGA interconnects was measured as a function of increasing number of thermal cycles. Electrical continuity measurements of daisy chains have shown no anomalies, even until 596 thermal cycles. Optical inspections of hardware have shown a significant fatigue for CCGA 1152 packages over CCGA 1272 packages. No catastrophic failures have been observed yet in the results. Process qualification and assembly are required to optimize the CCGA assembly processes. Optical inspections of CCGA boards have been made after 258 and 596 thermal cycles. Corner columns have started showing significant fatigue per optical inspection results.

Emerging Technologies for Assembly of Microscale Hydrogels

PubMed Central

Kavaz, Doga; Demirel, Melik C.; Demirci, Utkan

2013-01-01

Assembly of cell encapsulating building blocks (i.e., microscale hydrogels) has significant applications in areas including regenerative medicine, tissue engineering, and cell-based in vitro assays for pharmaceutical research and drug discovery. Inspired by the repeating functional units observed in native tissues and biological systems (e.g., the lobule in liver, the nephron in kidney), assembly technologies aim to generate complex tissue structures by organizing microscale building blocks. Novel assembly technologies enable fabrication of engineered tissue constructs with controlled properties including tunable microarchitectural and predefined compositional features. Recent advances in micro- and nano-scale technologies have enabled engineering of microgel based three dimensional (3D) constructs. There is a need for high-throughput and scalable methods to assemble microscale units with a complex 3D micro-architecture. Emerging assembly methods include novel technologies based on microfluidics, acoustic and magnetic fields, nanotextured surfaces, and surface tension. In this review, we survey emerging microscale hydrogel assembly methods offering rapid, scalable microgel assembly in 3D, and provide future perspectives and discuss potential applications. PMID:23184717

36. CONTEXT VIEW LOOKING SOUTHWEST OF BUILDING 233 (MISSLE ASSEMBLY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. CONTEXT VIEW LOOKING SOUTHWEST OF BUILDING 233 (MISSLE ASSEMBLY SHOP) IN ASSEMBLY AREA. - Loring Air Force Base, Weapons Storage Area, Northeastern corner of base at northern end of Maine Road, Limestone, Aroostook County, ME

35. EAST FRONT ELEVATION OF BUILDING 233 (MISSLE ASSEMBLY SHOP) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. EAST FRONT ELEVATION OF BUILDING 233 (MISSLE ASSEMBLY SHOP) IN ASSEMBLY AREA. - Loring Air Force Base, Weapons Storage Area, Northeastern corner of base at northern end of Maine Road, Limestone, Aroostook County, ME

DNAzyme-Based Logic Gate-Mediated DNA Self-Assembly.

PubMed

Zhang, Cheng; Yang, Jing; Jiang, Shuoxing; Liu, Yan; Yan, Hao

2016-01-13

Controlling DNA self-assembly processes using rationally designed logic gates is a major goal of DNA-based nanotechnology and programming. Such controls could facilitate the hierarchical engineering of complex nanopatterns responding to various molecular triggers or inputs. Here, we demonstrate the use of a series of DNAzyme-based logic gates to control DNA tile self-assembly onto a prescribed DNA origami frame. Logic systems such as "YES," "OR," "AND," and "logic switch" are implemented based on DNAzyme-mediated tile recognition with the DNA origami frame. DNAzyme is designed to play two roles: (1) as an intermediate messenger to motivate downstream reactions and (2) as a final trigger to report fluorescent signals, enabling information relay between the DNA origami-framed tile assembly and fluorescent signaling. The results of this study demonstrate the plausibility of DNAzyme-mediated hierarchical self-assembly and provide new tools for generating dynamic and responsive self-assembly systems.

Confirmatory Test of the Irritant Gas Disperser, Helicopter- or Vehicle- Mounted, M5

DTIC Science & Technology

1962-07-23

disperser consists of four major assemblies: An agent-container assembly, a pressure - group assembly, a support assembly, and a throat assembly. (1) The...base. (2) The pressure - group assembly consists of two steel high-pressure tanks, secured by steel band clamps to the pressure - group support assembly...aluminum alloy tubing welded together to provide a support for the agent-container assembly and the pressure - group assembly. Each of these separate

Diagnosing the Magnetic Field Structure of a Coronal Cavity Observed during the 2017 Total Solar Eclipse

NASA Astrophysics Data System (ADS)

Chen, Yajie; Tian, Hui; Su, Yingna; Qu, Zhongquan; Deng, Linhua; Jibben, Patricia R.; Yang, Zihao; Zhang, Jingwen; Samanta, Tanmoy; He, Jiansen; Wang, Linghua; Zhu, Yingjie; Zhong, Yue; Liang, Yu

2018-03-01

We present an investigation of a coronal cavity observed above the western limb in the coronal red line Fe X 6374 Å using a telescope of Peking University and in the green line Fe XIV 5303 Å using a telescope of Yunnan Observatories, Chinese Academy of Sciences, during the total solar eclipse on 2017 August 21. A series of magnetic field models is constructed based on the magnetograms taken by the Helioseismic and Magnetic Imager on board the Solar Dynamics Observatory (SDO) one week before the eclipse. The model field lines are then compared with coronal structures seen in images taken by the Atmospheric Imaging Assembly on board SDO and in our coronal red line images. The best-fit model consists of a flux rope with a twist angle of 3.1π, which is consistent with the most probable value of the total twist angle of interplanetary flux ropes observed at 1 au. Linear polarization of the Fe XIII 10747 Å line calculated from this model shows a “lagomorphic” signature that is also observed by the Coronal Multichannel Polarimeter of the High Altitude Observatory. We also find a ring-shaped structure in the line-of-sight velocity of Fe XIII 10747 Å, which implies hot plasma flows along a helical magnetic field structure, in the cavity. These results suggest that the magnetic structure of the cavity is a highly twisted flux rope, which may erupt eventually. The temperature structure of the cavity has also been investigated using the intensity ratio of Fe XIII 10747 Å and Fe X 6374 Å.

77 FR 15753 - Request for Nominations of Experts for a Science Advisory Board Panel To Review EPA's Web-Based...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... Advisory Board Panel To Review EPA's Web-Based Report on the Environment AGENCY: Environmental Protection... nominations of technical experts to form an SAB panel to review the Agency's Web-based Report on the... procedural policies. EPA's Web-based Report on the Environment (ROE) has been developed to provide a...

Split WHO in two: strengthening political decision-making and securing independent scientific advice.

PubMed

Hoffman, Steven J; Røttingen, John-Arne

2014-02-01

The World Health Organization (WHO) has never fulfilled its original mission of simultaneously serving as the world's pre-eminent public health authority and intergovernmental platform for global health negotiations. While WHO's secretariat works hard to fulfill both functions, it is undermined by an institutional design that mixes technical and political mandates. This forces staff to walk uncomfortably along many fine lines: advising but never directing; guiding but never governing; leading but never advocating; evaluating but never judging. The result is mediocrity on both fronts. Instead, WHO should be split in two, separating its technical and political stewardship functions into separate entities, with collaboration in areas of overlap. The Executive Board and secretariat would be bifurcated, with technical units reporting to a Technical Board and political units reporting to a Political Board. Both boards would report to the World Health Assembly where all member states would continue to provide ultimate oversight. Such bold changes can be implemented either by revising WHO's constitution or through simpler mechanisms. Either way, structural governance reforms would need to be accompanied by complementary changes in culture that support strengthened political decision-making and scientific independence. States' inability to act on WHO's institutional design challenges will only lead them and non-state actors to continue bypassing the organization through the creation of new entities as they have done over the last 15 years. The key will be to mobilize those advocates and decision-makers who have the audacity to demand more from WHO and convince member states to elevate their ambitions in current WHO reform efforts. Continued progress in global health depends on it. Copyright © 2013 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

76 FR 32241 - Civil Service Retirement System; Present Value Factors

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-03

... in the economic assumptions adopted by the Board of Actuaries of the Civil Service Retirement System... data to the Board of Actuaries, care of Gregory Kissel, Actuary, Office of Planning and Policy Analysis...- 335, based on changed economic assumptions adopted by the Board of Actuaries of the CSRS. Those...

Method and system for environmentally adaptive fault tolerant computing

NASA Technical Reports Server (NTRS)

Copenhaver, Jason L. (Inventor); Jeremy, Ramos (Inventor); Wolfe, Jeffrey M. (Inventor); Brenner, Dean (Inventor)

2010-01-01

A method and system for adapting fault tolerant computing. The method includes the steps of measuring an environmental condition representative of an environment. An on-board processing system's sensitivity to the measured environmental condition is measured. It is determined whether to reconfigure a fault tolerance of the on-board processing system based in part on the measured environmental condition. The fault tolerance of the on-board processing system may be reconfigured based in part on the measured environmental condition.

Rankings of Economics Faculties and Representation on Editorial Boards of Top Journals.

ERIC Educational Resources Information Center

Gibbons, Jean D.; Fish, Mary

1991-01-01

Presents rankings of U.S., university, economics departments. Explains the rankings are based upon representation of the departments on the editorial boards of leading economics journals. Reports that results are similar to rankings based upon other criteria. (DK)

Whispering-gallery-mode-based seismometer

DOEpatents

Fourguette, Dominique Claire; Otugen, M Volkan; Larocque, Liane Marie; Ritter, Greg Aan; Meeusen, Jason Jeffrey; Ioppolo, Tindaro

2014-06-03

A whispering-gallery-mode-based seismometer provides for receiving laser light into an optical fiber, operatively coupling the laser light from the optical fiber into a whispering-gallery-mode-based optical resonator, operatively coupling a spring of a spring-mass assembly to a housing structure; and locating the whispering-gallery-mode-based optical resonator between the spring-mass assembly and the housing structure so as to provide for compressing the whispering-gallery-mode-based optical resonator between the spring-mass assembly and the housing structure responsive to a dynamic compression force from the spring-mass assembly responsive to a motion of the housing structure relative to an inertial frame of reference.

Effects of PCB Pad Metal Finishes on the Cu-Pillar/Sn-Ag Micro Bump Joint Reliability of Chip-on-Board (COB) Assembly

NASA Astrophysics Data System (ADS)

Kim, Youngsoon; Lee, Seyong; Shin, Ji-won; Paik, Kyung-Wook

2016-06-01

While solder bumps have been used as the bump structure to form the interconnection during the last few decades, the continuing scaling down of devices has led to a change in the bump structure to Cu-pillar/Sn-Ag micro-bumps. Cu-pillar/Sn-Ag micro-bump interconnections differ from conventional solder bump interconnections in terms of their assembly processing and reliability. A thermo-compression bonding method with pre-applied b-stage non-conductive films has been adopted to form solder joints between Cu pillar/Sn-Ag micro bumps and printed circuit board vehicles, using various pad metal finishes. As a result, various interfacial inter-metallic compounds (IMCs) reactions and stress concentrations occur at the Cu pillar/Sn-Ag micro bumps joints. Therefore, it is necessary to investigate the influence of pad metal finishes on the structural reliability of fine pitch Cu pillar/Sn-Ag micro bumps flip chip packaging. In this study, four different pad surface finishes (Thin Ni ENEPIG, OSP, ENEPIG, ENIG) were evaluated in terms of their interconnection reliability by thermal cycle (T/C) test up to 2000 cycles at temperatures ranging from -55°C to 125°C and high-temperature storage test up to 1000 h at 150°C. The contact resistances of the Cu pillar/Sn-Ag micro bump showed significant differences after the T/C reliability test in the following order: thin Ni ENEPIG > OSP > ENEPIG where the thin Ni ENEPIG pad metal finish provided the best Cu pillar/Sn-Ag micro bump interconnection in terms of bump joint reliability. Various IMCs formed between the bump joint areas can account for the main failure mechanism.

Multicomponent self-assembly as a tool to harness new properties from peptides and proteins in material design.

PubMed

Okesola, Babatunde O; Mata, Alvaro

2018-05-21

Nature is enriched with a wide variety of complex, synergistic, and highly functional protein-based multicomponent assemblies. As such, nature has served as a source of inspiration for using multicomponent self-assembly as a platform to create highly ordered, complex, and dynamic protein and peptide-based nanostructures. Such an assembly system relies on the initial interaction of distinct individual building blocks leading to the formation of a complex that subsequently assembles into supramolecular architectures. This approach not only serves as a powerful platform for gaining insight into how proteins co-assemble in nature but also offers huge opportunities to harness new properties not inherent in the individual building blocks. In the past decades, various multicomponent self-assembly strategies have been used to extract synergistic properties from proteins and peptides. This review highlights the updates in the field of multicomponent self-assembly of proteins and peptides and summarizes various strategies, including covalent conjugation, ligand-receptor interactions, templated/directed assembly and non-specific co-assembly, for driving the self-assembly of multiple proteins and peptide-based building blocks into functional materials. In particular, we focus on peptide- or protein-containing multicomponent systems that, upon self-assembly, enable the emergence of new properties or phenomena. The ultimate goal of this review is to highlight the importance of multicomponent self-assembly in protein and peptide engineering, and to advocate its growth in the fields of materials science and nanotechnology.

An improved genome assembly uncovers prolific tandem repeats in Atlantic cod.

PubMed

Tørresen, Ole K; Star, Bastiaan; Jentoft, Sissel; Reinar, William B; Grove, Harald; Miller, Jason R; Walenz, Brian P; Knight, James; Ekholm, Jenny M; Peluso, Paul; Edvardsen, Rolf B; Tooming-Klunderud, Ave; Skage, Morten; Lien, Sigbjørn; Jakobsen, Kjetill S; Nederbragt, Alexander J

2017-01-18

The first Atlantic cod (Gadus morhua) genome assembly published in 2011 was one of the early genome assemblies exclusively based on high-throughput 454 pyrosequencing. Since then, rapid advances in sequencing technologies have led to a multitude of assemblies generated for complex genomes, although many of these are of a fragmented nature with a significant fraction of bases in gaps. The development of long-read sequencing and improved software now enable the generation of more contiguous genome assemblies. By combining data from Illumina, 454 and the longer PacBio sequencing technologies, as well as integrating the results of multiple assembly programs, we have created a substantially improved version of the Atlantic cod genome assembly. The sequence contiguity of this assembly is increased fifty-fold and the proportion of gap-bases has been reduced fifteen-fold. Compared to other vertebrates, the assembly contains an unusual high density of tandem repeats (TRs). Indeed, retrospective analyses reveal that gaps in the first genome assembly were largely associated with these TRs. We show that 21% of the TRs across the assembly, 19% in the promoter regions and 12% in the coding sequences are heterozygous in the sequenced individual. The inclusion of PacBio reads combined with the use of multiple assembly programs drastically improved the Atlantic cod genome assembly by successfully resolving long TRs. The high frequency of heterozygous TRs within or in the vicinity of genes in the genome indicate a considerable standing genomic variation in Atlantic cod populations, which is likely of evolutionary importance.

Prodrugs as self-assembled hydrogels: a new paradigm for biomaterials.

PubMed

Vemula, Praveen Kumar; Wiradharma, Nikken; Ankrum, James A; Miranda, Oscar R; John, George; Karp, Jeffrey M

2013-12-01

Prodrug-based self-assembled hydrogels represent a new class of active biomaterials that can be harnessed for medical applications, in particular the design of stimuli responsive drug delivery devices. In this approach, a promoiety is chemically conjugated to a known-drug to generate an amphiphilic prodrug that is capable of forming self-assembled hydrogels. Prodrug-based self-assembled hydrogels are advantageous as they alter the solubility of the drug, enhance drug loading, and eliminate the use of harmful excipients. In addition, self-assembled prodrug hydrogels can be designed to undergo controlled drug release or tailored degradation in response to biological cues. Herein we review the development of prodrug-based self-assembled hydrogels as an emerging class of biomaterials that overcome several common limitations encountered in conventional drug delivery. Published by Elsevier Ltd.

High-Repeatability, Robot Friendly, ORU Interface

NASA Technical Reports Server (NTRS)

Voellmer, George M. (Inventor)

1992-01-01

A robot-friendly coupling device for an Orbital Replacement Unit (ORU). The invention will provide a coupling that is detached and attached remotely by a robot. The design of the coupling must allow for slight misalignments, over torque protection, and precision placement. This is accomplished by using of a triangular interface having three components. A base plate assembly is located on an attachment surface, such as a satellite. The base plate assembly has a cup member, a slotted member, and a post member. The ORU that the robot attaches to the base plate assembly has an ORU plate assembly with two cone members and a post member which mate to the base plate assembly. As the two plates approach one another, one cone member of the ORU plate assembly only has to be placed accurately enough to fall into the cup member of the base plate assembly. The cup forces alignment until a second cone falls into a slotted member which provides final alignment. A single bolt is used to attach the two plates. Two deflecting plates are attached to the backs of the plates. When pressure is applied to the center of the deflecting plates, the force is distributed preventing the ORU & base plates from deflecting. This accounts for precision in the placement of the article.

Point-of-care syndrome-based, rapid diagnosis of infections on commercial ships.

PubMed

Bouricha, Mehdi; Samad, Marc Abdul; Levy, Pierre-Yves; Raoult, Didier; Drancourt, Michel

2014-01-01

Suspicion of contagious disease on commercial ships tends to be poorly managed, as there is little capacity to confirm a case on board except for malaria. Here we implemented a point-of-care (POC) laboratory on one container ship and one cruise ship for the rapid syndrome-based diagnosis of infectious diseases on board. In 2012 we implemented a POC laboratory on board a freight ship and on board a cruise ship. The POC laboratory ran a total of six different color-coded, syndrome-based kits incorporating 10 different commercially available immunochromatographic tests. The POC tests were taught within 1-hour as part of training to staff without any previous knowledge in microbiology. Compared with terrestrial POCs, specific constraints included the necessity to secure POC devices into the motile ship, to use robust devices, to overcome difficulties in communicating with the core laboratory, and to overcome limited intimacy of patients. However, a total of 36 POC tests were easily performed and yielded contributive negative results. This first experiment indicates that it is possible to run POC laboratories by nonexpert staff after providing rapid teaching course on board commercial ships. Generalization of on-board POC laboratories is expected to help in improving the medical management of staff and passengers. © 2013 International Society of Travel Medicine.

UniBoard: generic hardware for radio astronomy signal processing

NASA Astrophysics Data System (ADS)

Hargreaves, J. E.

2012-09-01

UniBoard is a generic high-performance computing platform for radio astronomy, developed as a Joint Research Activity in the RadioNet FP7 Programme. The hardware comprises eight Altera Stratix IV Field Programmable Gate Arrays (FPGAs) interconnected by a high speed transceiver mesh. Each FPGA is connected to two DDR3 memory modules and three external 10Gbps ports. In addition, a total of 128 low voltage differential input lines permit connection to external ADC cards. The DSP capability of the board exceeds 644E9 complex multiply-accumulate operations per second. The first production run of eight boards was distributed to partners in The Netherlands, France, Italy, UK, China and Korea in May 2011, with a further production runs completed in December 2011 and early 2012. The function of the board is determined by the firmware loaded into its FPGAs. Current applications include beamformers, correlators, digital receivers, RFI mitigation for pulsar astronomy, and pulsar gating and search machines The new UniBoard based correlator for the European VLBI network (EVN) uses an FX architecture with half the resources of the board devoted to station based processing: delay and phase correction and channelization, and half to the correlation function. A single UniBoard can process a 64MHz band from 32 stations, 2 polarizations, sampled at 8 bit. Adding more UniBoards can expand the total bandwidth of the correlator. The design is able to process both prerecorded and real time (eVLBI) data.

High-Speed On-Board Data Processing for Science Instruments

NASA Technical Reports Server (NTRS)

Beyon, Jeffrey Y.; Ng, Tak-Kwong; Lin, Bing; Hu, Yongxiang; Harrison, Wallace

2014-01-01

A new development of on-board data processing platform has been in progress at NASA Langley Research Center since April, 2012, and the overall review of such work is presented in this paper. The project is called High-Speed On-Board Data Processing for Science Instruments (HOPS) and focuses on a high-speed scalable data processing platform for three particular National Research Council's Decadal Survey missions such as Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS), Aerosol-Cloud-Ecosystems (ACE), and Doppler Aerosol Wind Lidar (DAWN) 3-D Winds. HOPS utilizes advanced general purpose computing with Field Programmable Gate Array (FPGA) based algorithm implementation techniques. The significance of HOPS is to enable high speed on-board data processing for current and future science missions with its reconfigurable and scalable data processing platform. A single HOPS processing board is expected to provide approximately 66 times faster data processing speed for ASCENDS, more than 70% reduction in both power and weight, and about two orders of cost reduction compared to the state-of-the-art (SOA) on-board data processing system. Such benchmark predictions are based on the data when HOPS was originally proposed in August, 2011. The details of these improvement measures are also presented. The two facets of HOPS development are identifying the most computationally intensive algorithm segments of each mission and implementing them in a FPGA-based data processing board. A general introduction of such facets is also the purpose of this paper.

A Framework for the Development of Automatic DFA Method to Minimize the Number of Components and Assembly Reorientations

NASA Astrophysics Data System (ADS)

Alfadhlani; Samadhi, T. M. A. Ari; Ma’ruf, Anas; Setiasyah Toha, Isa

2018-03-01

Assembly is a part of manufacturing processes that must be considered at the product design stage. Design for Assembly (DFA) is a method to evaluate product design in order to make it simpler, easier and quicker to assemble, so that assembly cost is reduced. This article discusses a framework for developing a computer-based DFA method. The method is expected to aid product designer to extract data, evaluate assembly process, and provide recommendation for the product design improvement. These three things are desirable to be performed without interactive process or user intervention, so product design evaluation process could be done automatically. Input for the proposed framework is a 3D solid engineering drawing. Product design evaluation is performed by: minimizing the number of components; generating assembly sequence alternatives; selecting the best assembly sequence based on the minimum number of assembly reorientations; and providing suggestion for design improvement.

76 FR 65540 - National Space-Based Positioning, Navigation, and Timing (PNT) Advisory Board; Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-21

.... James J. Miller, Human Exploration and Operations Mission Directorate, National Aeronautics and Space... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (11-099)] National Space-Based Positioning, Navigation, and Timing (PNT) Advisory Board; Meeting AGENCY: National Aeronautics and Space Administration...

A design approach for small vision-based autonomous vehicles

NASA Astrophysics Data System (ADS)

Edwards, Barrett B.; Fife, Wade S.; Archibald, James K.; Lee, Dah-Jye; Wilde, Doran K.

2006-10-01

This paper describes the design of a small autonomous vehicle based on the Helios computing platform, a custom FPGA-based board capable of supporting on-board vision. Target applications for the Helios computing platform are those that require lightweight equipment and low power consumption. To demonstrate the capabilities of FPGAs in real-time control of autonomous vehicles, a 16 inch long R/C monster truck was outfitted with a Helios board. The platform provided by such a small vehicle is ideal for testing and development. The proof of concept application for this autonomous vehicle was a timed race through an environment with obstacles. Given the size restrictions of the vehicle and its operating environment, the only feasible on-board sensor is a small CMOS camera. The single video feed is therefore the only source of information from the surrounding environment. The image is then segmented and processed by custom logic in the FPGA that also controls direction and speed of the vehicle based on visual input.

Pc-based car license plate reading

NASA Astrophysics Data System (ADS)

Tanabe, Katsuyoshi; Marubayashi, Eisaku; Kawashima, Harumi; Nakanishi, Tadashi; Shio, Akio

1994-03-01

A PC-based car license plate recognition system has been developed. The system recognizes Chinese characters and Japanese phonetic hiragana characters as well as six digits on Japanese license plates. The system consists of a CCD camera, vehicle sensors, a strobe unit, a monitoring center, and an i486-based PC. The PC includes in its extension slots: a vehicle detector board, a strobe emitter board, and an image grabber board. When a passing vehicle is detected by the vehicle sensors, the strobe emits a pulse of light. The light pulse is synchronized with the time the vehicle image is frozen on an image grabber board. The recognition process is composed of three steps: image thresholding, character region extraction, and matching-based character recognition. The recognition software can handle obscured characters. Experimental results for hundreds of outdoor images showed high recognition performance within relatively short performance times. The results confirmed that the system is applicable to a wide variety of applications such as automatic vehicle identification and travel time measurement.

Portable air pollution control equipment for the control of toxic particulate emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chaurushia, A.; Odabashian, S.; Busch, E.

1997-12-31

Chromium VI (Cr VI) has been identified by the environmental regulatory agencies as a potent carcinogen among eleven heavy metals. A threshold level of 0.0001 lb/year for Cr VI emissions has been established by the California Air Resources Board for reporting under Assembly Bill 2588. A need for an innovative control technology to reduce fugitive emissions of Cr VI was identified during the Air Toxic Emissions Reduction Program at Northrop Grumman Military Aircraft Systems Division (NGMASD). NGMASD operates an aircraft assembly facility in El Segundo, CA. Nearly all of the aircraft components are coated with a protective coating (primer) priormore » to assembly. The primer has Cr VI as a component for its excellent corrosion resistance property. The complex assembly process requires fasteners which also need primer coating. Therefore, NGMASD utilizes High Volume Low Pressure (HVLP) guns for the touch-up spray coating operations. During the touch-up spray coating operations, Cr VI particles are atomized and transferred to the aircraft surface. The South Coast Air Quality Management District (SCAQMD) has determined that the HVLP gun transfers 65% of the paint particles onto the substrate and the remaining 35% are emitted as an overspray if air pollution controls are not applied. NGMASD has developed the Portable Air Pollution Control Equipment (PAPCE) to capture and control the overspray in order to reduce fugitive Cr VI emissions from the touch-up spray coating operations. A source test was performed per SCAQMD guidelines and the final report has been approved by the SCAQMD.« less

Independent assessment and improvement of wheat genome sequence assemblies using Fosill jumping libraries.

PubMed

Lu, Fu-Hao; McKenzie, Neil; Kettleborough, George; Heavens, Darren; Clark, Matthew D; Bevan, Michael W

2018-05-01

The accurate sequencing and assembly of very large, often polyploid, genomes remains a challenging task, limiting long-range sequence information and phased sequence variation for applications such as plant breeding. The 15-Gb hexaploid bread wheat (Triticum aestivum) genome has been particularly challenging to sequence, and several different approaches have recently generated long-range assemblies. Mapping and understanding the types of assembly errors are important for optimising future sequencing and assembly approaches and for comparative genomics. Here we use a Fosill 38-kb jumping library to assess medium and longer-range order of different publicly available wheat genome assemblies. Modifications to the Fosill protocol generated longer Illumina sequences and enabled comprehensive genome coverage. Analyses of two independent Bacterial Artificial Chromosome (BAC)-based chromosome-scale assemblies, two independent Illumina whole genome shotgun assemblies, and a hybrid Single Molecule Real Time (SMRT-PacBio) and short read (Illumina) assembly were carried out. We revealed a surprising scale and variety of discrepancies using Fosill mate-pair mapping and validated several of each class. In addition, Fosill mate-pairs were used to scaffold a whole genome Illumina assembly, leading to a 3-fold increase in N50 values. Our analyses, using an independent means to validate different wheat genome assemblies, show that whole genome shotgun assemblies based solely on Illumina sequences are significantly more accurate by all measures compared to BAC-based chromosome-scale assemblies and hybrid SMRT-Illumina approaches. Although current whole genome assemblies are reasonably accurate and useful, additional improvements will be needed to generate complete assemblies of wheat genomes using open-source, computationally efficient, and cost-effective methods.

Connections and Tensions between University and School Districts: Research Review Boards and School-Based Research

ERIC Educational Resources Information Center

Tilley, Susan A.; Killins, Janet; Van Oosten, Deborah

2005-01-01

Currently researchers connected to university contexts who conduct research involving human participants must receive approval from a research ethics board, and in the case of school-based research, from school district authorities. This article focuses on the ethics review of school-based research. Applications submitted to a research ethics…

Understanding Motivators and Challenges to Involving Urban Parents as Collaborators in HIV Prevention Research Efforts.

PubMed

McKay, Mary M; Pinto, Rogério M; Bannon, William M; Guilamo-Ramos, Vincent

2007-01-01

This study was designed to explore the experiences of urban parents in their role as Collaborative Board members as part of the CHAMP (Collaborative HIV prevention and Adolescent Mental health Project) Family Program Study. The CHAMP Collaborative Board is comprised of urban parents, representatives from schools and community-based agencies and university-based researchers and is charged with overseeing the design, delivery and testing of a family-based HIV prevention program for pre and early adolescent youth. The current qualitative study, guided by the Theory of Unified Behavior Change, is meant to elucidate: (1) pathways to involvement by urban parents; (2) benefits and costs of participating in this collaborative HIV prevention research effort; and (3) the role of social relationships in influencing initial and ongoing participation by parent participants. Twenty-nine parent Collaborative Board members were interviewed for this study. In-depth interviews were audio recorded and ranged from 30 to 90 minutes in length. Transcripts were coded and analyzed using NUD*IST, computerized software used for examining narratives. Findings include community parent members identifying social support and learning opportunities as major reasons for involvement with the Collaborative Board. Prior involvement with other community-based projects and knowledge of at least one other person on the Board also influenced members to join the Board and remain involved over time. Further, recommendations for future collaborative partnerships are made. Findings have direct implication for participatory HIV prevention research activities.

Sampling and Control Circuit Board for an Inertial Measurement Unit

NASA Technical Reports Server (NTRS)

Chelmins, David T (Inventor); Sands, Obed (Inventor); Powis, Richard T., Jr. (Inventor)

2016-01-01

A circuit board that serves as a control and sampling interface to an inertial measurement unit ("IMU") is provided. The circuit board is also configured to interface with a local oscillator and an external trigger pulse. The circuit board is further configured to receive the external trigger pulse from an external source that time aligns the local oscillator and initiates sampling of the inertial measurement device for data at precise time intervals based on pulses from the local oscillator. The sampled data may be synchronized by the circuit board with other sensors of a navigation system via the trigger pulse.

Novel use of the Wii Balance Board to prospectively predict falls in community-dwelling older adults.

PubMed

Kwok, Boon-Chong; Clark, Ross A; Pua, Yong-Hao

2015-06-01

The Wii Balance Board has received increasing attention as a balance measurement tool; however its ability to prospectively predict falls is unknown. This exploratory study investigated the use of the Wii Balance Board and other clinical-based measures for prospectively predicting falls among community-dwelling older adults. Seventy-three community-dwelling men and women, aged 60-85years were followed-up over a year for falls. Standing balance was indexed by sway velocities measured using the Wii Balance Board interfaced with a laptop. Clinical-based measures included Short Physical Performance Battery, gait speed and Timed-Up-and-Go test. Multivariable regression analyses were used to assess the ability of the Wii Balance Board measure to complement the TUG test in fall screening. Individually, the study found Wii Balance Board anteroposterior (odds ratio 1.98, 95% CI 1.16 to 3.40, P=0.01) and mediolateral (odds ratio 2.80, 95% CI 1.10 to 7.13, p=0.03) sway velocity measures predictive of prospective falls. However, when each velocity measure was adjusted with body mass index and Timed-Up-and-Go, only anteroposterior sway velocity was predictive of prospective falls (odds ratio 2.21, 95% CI 1.18 to 4.14). A faster anteroposterior velocity was associated with increased odds of falling. Area-under-the-curves for Wii Balance Board sway velocities were 0.67 and 0.71 for anteroposterior and mediolateral respectively. The Wii Balance Board-derived anteroposterior sway velocity measure could complement existing clinical-based measures in predicting future falls among community-dwelling older adults. Australian New Zealand Clinical Trials Registry number: ACTRN12610001099011. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison between two models of energy balance in coronal loops

NASA Astrophysics Data System (ADS)

Mac Cormack, C.; López Fuentes, M.; Vásquez, A. M.; Nuevo, F. A.; Frazin, R. A.; Landi, E.

2017-10-01

In this work we compare two models to analyze the energy balance along coronal magnetic loops. For the first stationary model we deduce an expression of the energy balance along the loops expressed in terms of quantities provided by the combination of differential emission measure tomography (DEMT) applied to EUV images time series and potential extrapolations of the coronal magnetic field. The second applied model is a 0D hydrodynamic model that provides the evolution of the average properties of the coronal plasma along the loops, using as input parameters the loop length and the heating rate obtained with the first model. We compare the models for two Carrington rotations (CR) corresponding to different periods of activity: CR 2081, corresponding to a period of minimum activity observed with the Extreme Ultraviolet Imager (EUVI) on board of the Solar Terrestrial Relations Observatory (STEREO), and CR 2099, corresponding to a period of activity increase observed with the Atmospheric Imaging Assembly (AIA) on board the Solar Dynamics Observatory (SDO). The results of the models are consistent for both rotations.