The effect of muscle stiffness and damping on simulated impact force peaks during running.

PubMed

Nigg, B M; Liu, W

1999-08-01

It has been frequently reported that vertical impact force peaks during running change only minimally when changing the midsole hardness of running shoes. However, the underlying mechanism for these experimental observations is not well understood. An athlete has various possibilities to influence external and internal forces during ground contact (e.g. landing velocity, geometrical alignment, muscle tuning, etc.). The purpose of this study was to discuss one possible strategy to influence external impact forces acting on the athlete's body during running, the strategy to change muscle activity (muscle tuning). The human body was modeled as a simplified mass-spring-damper system. The model included masses of the upper and the lower bodies with each part of the body represented by a rigid and a non-rigid wobbling mass. The influence of mechanical properties of the human body on the vertical impact force peak was examined by varying the spring constants and damping coefficients of the spring-damper units that connected the various masses. Two types of shoe soles were modeled using a non-linear force deformation model with two sets of parameters based on the force-deformation curves of pendulum impact experiments. The simulated results showed that the regulation of the mechanical coupling of rigid and wobbling masses of the human body had an influence on the magnitude of the vertical impact force, but not on its loading rate. It was possible to produce the same impact force peaks altering specific mechanical properties of the system for a soft and a hard shoe sole. This regulation can be achieved through changes of joint angles, changes in joint angular velocities and/or changes in muscle activation levels in the lower extremity. Therefore, it has been concluded that changes in muscle activity (muscle tuning) can be used as a possible strategy to affect vertical impact force peaks during running.

Partial Validation of Multibody Program to Optimize Simulated Trajectories II (POST II) Parachute Simulation With Interacting Forces

NASA Technical Reports Server (NTRS)

Raiszadeh, Ben; Queen, Eric M.

2002-01-01

A capability to simulate trajectories Of Multiple interacting rigid bodies has been developed. This capability uses the Program to Optimize Simulated Trajectories II (POST II). Previously, POST II had the ability to simulate multiple bodies without interacting forces. The current implementation is used for the Simulation of parachute trajectories, in which the parachute and suspended bodies can be treated as rigid bodies. An arbitrary set of connecting lines can be included in the model and are treated as massless spring-dampers. This paper discusses details of the connection line modeling and results of several test cases used to validate the capability.

Viscoelastic tides: models for use in Celestial Mechanics

NASA Astrophysics Data System (ADS)

Ragazzo, C.; Ruiz, L. S.

2017-05-01

This paper contains equations for the motion of linear viscoelastic bodies interacting under gravity. The equations are fully three dimensional and allow for the integration of the spin, the orbit, and the deformation of each body. The goal is to present good models for the tidal forces that take into account the possibly different rheology of each body. The equations are obtained within a finite dimension Lagrangian framework with dissipation function. The main contribution is a procedure to associate to each spring-dashpot model, which defines the rheology of a body, a potential and a dissipation function for the body deformation variables. The theory is applied to the Earth (solid part plus oceans) and a comparison between model and observation of the following quantities is made: norm of the Love numbers, rate of tidal energy dissipation, Chandler period, and Earth-Moon distance increase.

Comparison of environmental and body temperatures as predictors of mating call parameters of spring peepers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, L.E.; Brown, J.R.

1977-01-01

Parameters of the mating call of spring peepers (Hyla crucifer) were best predicted by water temperature rather than air or body temperature. Thus, water temperature should most closely approach the true body temperature of the calling frogs.

Kineto-dynamic design optimisation for vehicle-specific seat-suspension systems

NASA Astrophysics Data System (ADS)

Shangguan, Wen-Bin; Shui, Yijie; Rakheja, Subhash

2017-11-01

Designs and analyses of seat-suspension systems are invariably performed considering effective vertical spring rate and damping properties, while neglecting important contributions due to kinematics of the widely used cross-linkage mechanism. In this study, a kineto-dynamic model of a seat-suspension is formulated to obtain relations for effective vertical suspension stiffness and damping characteristics as functions of those of the air spring and the hydraulic damper, respectively. The proposed relations are verified through simulations of the multi-body dynamic model of the cross-linkage seat-suspension in the ADAMS platform. The validity of the kineto-dynamic model is also demonstrated through comparisons of its vibration transmission response with the experimental data. The model is used to identify optimal air spring coordinates to attain nearly constant natural frequency of the suspension, irrespective of the seated body mass and seated height. A methodology is further proposed to identify optimal damping requirements for vehicle-specific suspension designs to achieve minimal seat effective amplitude transmissibility (SEAT) and vibration dose value (VDV) considering vibration spectra of different classes of earthmoving vehicles. The shock and vibration isolation performance potentials of the optimal designs are evaluated under selected vehicle vibration superimposed with shock motions. Results show that the vehicle-specific optimal designs could provide substantial reductions in the SEAT and VDV values for the vehicle classes considered.

Propulsion via flexible flapping in granular media

NASA Astrophysics Data System (ADS)

Peng, Zhiwei; Ding, Yang; Pietrzyk, Kyle; Elfring, Gwynn J.; Pak, On Shun

2017-07-01

Biological locomotion in nature is often achieved by the interaction between a flexible body and its surrounding medium. The interaction of a flexible body with granular media is less understood compared with viscous fluids partially due to its complex rheological properties. In this work, we explore the effect of flexibility on granular propulsion by considering a simple mechanical model in which a rigid rod is connected to a torsional spring that is under a displacement actuation using a granular resistive force theory. Through a combined numerical and asymptotic investigation, we characterize the propulsive dynamics of such a flexible flapper in relation to the actuation amplitude and spring stiffness, and we compare these dynamics with those observed in a viscous fluid. In addition, we demonstrate that the maximum possible propulsive force can be obtained in the steady propulsion limit with a finite spring stiffness and large actuation amplitude. These results may apply to the development of synthetic locomotive systems that exploit flexibility to move through complex terrestrial media.

Patterns of lake occupancy by fish indicate different adaptations to life in a harsh Arctic environment

USGS Publications Warehouse

Haynes, Trevor B.; Rosenberger, Amanda E.; Lindberg, Mark S.; Whitman, Matthew; Schmutz, Joel A.

2014-01-01

Based on these patterns, we propose an overall model of primary controls on the distribution of fish on the Arctic Coastal Plain of Alaska. Harsh conditions, including lake freezing, limit occupancy in winter through extinction events while lake occupancy in spring and summer is driven by directional migration (large-bodied species) and undirected dispersal (small-bodied species).

Metal spring stub and ceramic body electrode assembly

DOEpatents

Rolf, Richard L.; Sharp, Maurice L.

1984-01-01

An electrode assembly comprising an electrically conductive ceramic electrode body having an opening therein and a metal stub retained in the opening with at least a surface of the stub in intimate contact with a surface of the body and the stub adapted with a spring to flex and prevent damage to the body from expansion of the stub when subjected to a temperature differential.

Spin ejector

DOEpatents

Andersen, John A.; Flanigan, John J.; Kindley, Robert J.

1978-01-01

The disclosure relates to an apparatus for spin ejecting a body having a flat plate base containing bosses. The apparatus has a base plate and a main ejection shaft extending perpendicularly from the base plate. A compressible cylindrical spring is disposed about the shaft. Bearings are located between the shaft and the spring. A housing containing a helical aperture releasably engages the base plate and surrounds the shaft bearings and the spring. A piston having an aperture follower disposed in the housing aperture is seated on the spring and is guided by the shaft and the aperture. The spring is compressed and when released causes the piston to spin eject the body.

Parental investment in the chicken turtle (Deirochelys reticularia)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.D.; Gibbons, J.W.; Greene, J.L.

1983-01-01

Eggs of the chicken turtle (Deirochelys reticularia) were collected in South Carolina from clutches laid in the spring and fall. Clutch size averaged 8.0 eggs (2 SE = 1.6; n = 15) and was weakly correlated with body size of the female. Wet mass of the clutch averaged 72.4 g (2 SE = 11.6, n = 15). There were no significant differences in clutch size or wet mass between spring and fall nesting seasons. Individual eggs laid in the fall (anti x = 10.7 g) were significantly larger than those laid in the spring (anti x = 8.5 g). Fifteenmore » eggs laid in the spring and incubated at 29/sup 0/ +- 2/sup 0/C averaged 152 d to hatching. Hatchling plastron length averaged 24.3 mm, and body wet mass was 6.7 g. Hatchlings (dry mass) contained 27.4% lipid, and the lipids remaining in the neonate at hatching represented 61% of the lipids originally present in the egg. The wet mass of a hatchling is highly correlated with wet mass of the egg. In contrast to clutch size, egg size had a strong positive relationship to body size. A morphological constraint, the width of the pelvic canal, is proposed as having an influence on this relationship. The negative relationship between an optimized egg size and clutch size was not evident, so current optimality models do not appear to be applicable to Deirochelys.« less

Sliding contact on the interface of elastic body and rigid surface using a single block Burridge-Knopoff model

NASA Astrophysics Data System (ADS)

Amireghbali, A.; Coker, D.

2018-01-01

Burridge and Knopoff proposed a mass-spring model to explore interface dynamics along a fault during an earthquake. The Burridge and Knopoff (BK) model is composed of a series of blocks of equal mass connected to each other by springs of same stiffness. The blocks also are attached to a rigid driver via another set of springs that pulls them at a constant velocity against a rigid substrate. They studied dynamics of interface for an especial case with ten blocks and a specific set of fault properties. In our study effects of Coulomb and rate-state dependent friction laws on the dynamics of a single block BK model is investigated. The model dynamics is formulated as a system of coupled nonlinear ordinary differential equations in state-space form which lends itself to numerical integration methods, e.g. Runge-Kutta procedure for solution. The results show that the rate and state dependent friction law has the potential of triggering dynamic patterns that are different from those under Coulomb law.

Overwintering temperature and body condition shift emergence dates of spring-emerging solitary bees.

PubMed

Schenk, Mariela; Mitesser, Oliver; Hovestadt, Thomas; Holzschuh, Andrea

2018-01-01

Solitary bees in seasonal environments must align their life-cycles with favorable environmental conditions and resources; the timing of their emergence is highly fitness relevant. In several bee species, overwintering temperature influences both emergence date and body weight at emergence. High variability in emergence dates among specimens overwintering at the same temperatures suggests that the timing of emergence also depends on individual body conditions. However, possible causes for this variability, such as individual differences in body size or weight, have been rarely studied. In a climate chamber experiment using two spring-emerging mason bees ( Osmia cornuta and O. bicornis ), we investigated the relationship between temperature, emergence date, body weight, and body size, the last of which is not affected by overwintering temperature. Our study showed that body weight declined during hibernation more strongly in warm than in cold overwintering temperatures. Although bees emerged earlier in warm than in cold overwintering temperatures, at the time of emergence, bees in warm overwintering temperatures had lower body weights than bees in cold overwintering temperatures (exception of male O. cornuta ). Among specimens that experienced the same overwintering temperatures, small and light bees emerged later than their larger and heavier conspecifics. Using a simple mechanistic model we demonstrated that spring-emerging solitary bees use a strategic approach and emerge at a date that is most promising for their individual fitness expectations. Our results suggest that warmer overwintering temperatures reduce bee fitness by causing a decrease in body weight at emergence. We showed furthermore that in order to adjust their emergence dates, bees use not only temperature but also their individual body condition as triggers. This may explain differing responses to climate warming within and among bee populations and may have consequences for bee-plant interactions as well as for the persistence of bee populations under climate change.

Metal spring stub and ceramic body electrode assembly

DOEpatents

Rolf, R.L.; Sharp, M.L.

1984-06-26

An electrode assembly is disclosed comprising an electrically conductive ceramic electrode body having an opening therein and a metal stub retained in the opening with at least a surface of the stub in intimate contact with a surface of the body and the stub adapted with a spring to flex and prevent damage to the body from expansion of the stub when subjected to a temperature differential. 1 fig.

Lipid reserves of Lesser Scaup (Aythya affinis) migrating across a large landscape are consistent with the "Spring Condition" hypothesis

USGS Publications Warehouse

Anteau, M.J.; Afton, A.D.

2009-01-01

The “spring condition” hypothesis (SCH) states that nutrition during spring migration affects survival, reproductive success, and, ultimately, population size of migratory birds. The North American population of Lesser Scaup (Aythya affinis) has experienced a marked decline, apparently because of poor recruitment. An important prediction of the SCH is that female Lesser Scaup have low lipid reserves during spring migration. We previously reported that lipid reserves and body mass of females collected on migratory stopover areas in northwestern Minnesota in springs 2000–2001 were lower than those on the same areas in the 1980s and markedly lower than those collected at Pool 19 of the Mississippi River in 2000–2001, an important preceding stopover area. However, it was unclear whether these findings represented a site-specific result or a landscape-scale phenomenon. Accordingly, we examined lipid and body mass of 641 female Lesser Scaup migrating across seven eco-physiographic regions of Iowa, Minnesota, and North Dakota during springs 2003–2005. We found that lipids and body mass of females throughout the Upper Midwest were similar to or less than the low values documented in northwestern Minnesota in springs 2000–2001 and markedly lower than those of females at Pool 19 in springs 2000–2001. Accordingly, our results are consistent with a prediction of the SCH, because lipid and body mass of females are low throughout this large landscape, lower than at an important preceding stopover area, and lower than all historical values. Finally, our results suggest the potential for cross-seasonal influences of nutrition on recruitment and that a stronger management focus on spring migration habitats may be necessary for conservation and recovery of declining migratory birds, especially Lesser Scaup.

Dynamic responses of railroad car models to vertical and lateral rail inputs

NASA Technical Reports Server (NTRS)

Sewall, J. L.; Parrish, R. V.; Durling, B. J.

1971-01-01

Simplified dynamic models were applied in a study of vibration in a high-speed railroad car. The mathematical models used were a four-degree-of-freedom model for vertical responses to vertical rail inputs and a ten-degree-of-freedom model for lateral response to lateral or rolling (cross-level) inputs from the rails. Elastic properties of the passenger car body were represented by bending and torsion of a uniform beam. Rail-to-car (truck) suspensions were modeled as spring-mass-dashpot oscillators. Lateral spring nonlinearities approximating certain complicated truck mechanisms were introduced. The models were excited by displacement and, in some cases, velocity inputs from the rails by both deterministic (including sinusoidal) and random input functions. Results were obtained both in the frequency and time domains. Solutions in the time domain for the lateral model were obtained for a wide variety of transient and random inputs generated on-line by an analog computer. Variations in one of the damping properties of the lateral car suspension gave large fluctuations in response over a range of car speeds for a given input. This damping coefficient was significant in reducing lateral car responses that were higher for nonlinear springs for three different inputs.

Analysis of effect of internal and operating variables on performance of SVDS constraint model (ABIND)

NASA Technical Reports Server (NTRS)

Pendergrass, J. R.; Walsh, R. L.

1975-01-01

An examination of the factors which modify the simulation of a constraint in the motion of the aft attach points of the orbiter and external tank during separation has been made. The factors considered were both internal (spring and damper constants) and external (friction coefficient and dynamic pressure). The results show that an acceptable choice of spring/damper constant combinations exist over the expected range of the external factors and that the choice is consistent with a practical integration interval. The constraint model is shown to produce about a 10 percent increase in the relative body pitch angles over the unconstrained case whereas the MDC-STL constraint model is shown to produce about a 38 percent increase.

Bifurcation and chaos in the simple passive dynamic walking model with upper body.

PubMed

Li, Qingdu; Guo, Jianli; Yang, Xiao-Song

2014-09-01

We present some rich new complex gaits in the simple walking model with upper body by Wisse et al. in [Robotica 22, 681 (2004)]. We first show that the stable gait found by Wisse et al. may become chaotic via period-doubling bifurcations. Such period-doubling routes to chaos exist for all parameters, such as foot mass, upper body mass, body length, hip spring stiffness, and slope angle. Then, we report three new gaits with period 3, 4, and 6; for each gait, there is also a period-doubling route to chaos. Finally, we show a practical method for finding a topological horseshoe in 3D Poincaré map, and present a rigorous verification of chaos from these gaits.

Bifurcation and chaos in the simple passive dynamic walking model with upper body

NASA Astrophysics Data System (ADS)

Li, Qingdu; Guo, Jianli; Yang, Xiao-Song

2014-09-01

We present some rich new complex gaits in the simple walking model with upper body by Wisse et al. in [Robotica 22, 681 (2004)]. We first show that the stable gait found by Wisse et al. may become chaotic via period-doubling bifurcations. Such period-doubling routes to chaos exist for all parameters, such as foot mass, upper body mass, body length, hip spring stiffness, and slope angle. Then, we report three new gaits with period 3, 4, and 6; for each gait, there is also a period-doubling route to chaos. Finally, we show a practical method for finding a topological horseshoe in 3D Poincaré map, and present a rigorous verification of chaos from these gaits.

Spring bloom dinoflagellate cyst dynamics in three eastern sub-basins of the Baltic Sea

NASA Astrophysics Data System (ADS)

Sildever, Sirje; Kremp, Anke; Enke, Annely; Buschmann, Fred; Maljutenko, Ilja; Lips, Inga

2017-04-01

Dinoflagellate cyst abundance and species composition were investigated before, during and after the spring bloom in the Gulf of Finland, north-eastern Baltic Proper and Gulf of Riga in order to detect spatial and temporal dynamics. Transport of newly formed cysts by currents was modelled to explore the possible distance travelled by cysts before sedimentation. The cyst community of the spring bloom dinoflagellates was dominated by the cysts of Biecheleria baltica in all basins, despite its marginal value in the planktonic spring bloom community in the Gulf of Riga. Dinoflagellate cyst abundance in the surface sediments displayed temporal dynamics in all basins, however, this appeared to be also influenced by physical processes. The model simulation showed that newly formed cysts are transported around 10-30 km from the point of origin before deposited. The latter suggests that transport of resting stages in the water column significantly affects spatial cyst distribution in the sediments and thus needs to be considered in the interpretation of temporal biological productivity patterns of a water body from cyst proxies.

A study on a wheel-based stair-climbing robot with a hopping mechanism

NASA Astrophysics Data System (ADS)

Kikuchi, Koki; Sakaguchi, Keisuke; Sudo, Takayuki; Bushida, Naoki; Chiba, Yasuhiro; Asai, Yuji

2008-08-01

In this study, we propose a simple hopping mechanism using the vibration of a two-degree-of-freedom system for a wheel-based stair-climbing robot. The robot, consisting of two bodies connected by springs and a wire, hops by releasing energy stored in the springs and quickly travels using wheels mounted in its lower body. The trajectories of the bodies during hopping change in accordance with the design parameters, such as the reduced mass of the two bodies, the mass ratio between the upper and lower bodies, the spring constant, the control parameters such as the initial contraction of the spring and the wire tension. This property allows the robot to quickly and economically climb up and down stairs, leap over obstacles, and landing softly without complex control. In this paper, the characteristics of hopping motion for the design and control parameters are clarified by both numerical simulations and experiments. Furthermore, using the robot design based on the results the abilities to hop up and down a step, leap over a cable, and land softly are demonstrated.

Thermoregulatory challenges in the habitat of the world's smallest tortoise, Chersobius signatus.

PubMed

Loehr, Victor J T

2018-01-01

Ectotherms have various means of dealing with low environmental temperatures, but relatively few species have been rigorously investigated. Consequently, we have little information to predict how ectotherm populations might respond to global temperature changes. Tortoises from temperate and subtropical regions often overcome periodically cool conditions by hibernation, but speckled dwarf tortoises (Chersobius signatus) need to remain active to exploit ephemeral resources in their arid winter-rainfall habitat. This study investigated how dwarf tortoises cope with low temperatures in winter and spring, by measuring thermal habitat quality and thermoregulation based on differently-sized operative temperature models in sun, shade, and in deep crevices. Investigations continued in summer and autumn to obtain a year-round picture of thermoregulatory challenges. Although large models (i.e., larger than dwarf tortoises) were expected to have lower operative temperatures than smaller models, due to the former's larger thermal inertia, all model sizes had similar temperatures. Hence, the species' small body size does not appear constrained by obtainable body temperatures in cool seasons. Nevertheless, low operative temperatures in winter posed a challenge for the tortoises, which reached their field-preferred body temperature for an average of only 0.8-0.9h per day. Moreover, a low thermoregulation effectiveness suggested that tortoises traded-off physiological benefits of favourable body temperatures against predation risk. Spring and autumn provided higher temperatures, but summer caused the greatest thermoregulatory challenge. Although summer body temperatures were closer to field-preferred body temperature than in any other season, tortoises required rock crevices to avoid overheating. The small size of dwarf tortoises might help them utilise crevices. In summer, maximum operative temperatures in crevices were similar to field-preferred body temperature, indicating that an increase in environmental temperatures might be detrimental to dwarf tortoises. In light of projected temperature rises, future studies should assess if dwarf tortoises can cope with higher environmental temperatures in summer. Copyright © 2017 Elsevier Ltd. All rights reserved.

Geochemistry and geobiology of a present-day serpentinization site in California: The Cedars

NASA Astrophysics Data System (ADS)

Morrill, Penny L.; Kuenen, J. Gijs; Johnson, Orion J.; Suzuki, Shino; Rietze, Amanda; Sessions, Alex L.; Fogel, Marilyn L.; Nealson, Kenneth H.

2013-05-01

Ultra-basic (pH 11-12) reducing (-656 to -585 mV) groundwater springs discharging from serpentinized peridotite of The Cedars, CA, were investigated for their geochemistry and geobiology. The spring waters investigated were of meteoric origin; however, geochemical modeling suggests that there were two sources of groundwater, a shallow source with sufficient contact with The Cedars' peridotite body to be altered geochemically by serpentinization, and a deeper groundwater source that not only flows through the peridotite body but was also in contact with the marine sediments of the Franciscan Subduction Complex (FSC) below the peridotite body. We propose that the groundwater discharging from lower elevations (GPS1 and CS1) reflect the geochemistry of the deeper groundwater in contact with FSC, while groundwaters discharging from springs at higher elevations (NS1 and BSC) were a mixture of the shallow peridotite-only groundwater and the deeper groundwater that has been in contact with the FSC. Cell densities of suspended microbes within these waters were extremely low. In the NS1 and BSC spring fluids, cell densities ranged from 102 to 103 cells/ml, while suspended cells at GPS were lower than 10 cells/mL. However, glass slides incubated in the BSC and GPS1 springs for 2-3 weeks were colonized by cells with densities ranging from 106 to 107 cells/cm2 attached to their surfaces. All of the springs were very low (⩽1 μM) in several essential elements and electron acceptors (e.g. nitrate/ammonium, sulfate, and phosphate) required for (microbial) growth, which is not uncommon at sites of continental serpentinization. Gases rich in N2, H2, and CH4 were exsolving from the springs. The stable carbon isotope value (δ13CCH4 = -68 ± 0.6‰) and the CH4/C2+ (>103) of methane and other gaseous hydrocarbons exsolving from NS1 were typical of microbially sourced methane, whereas the isotope values and the CH4/C2+ of BSC and CS1 springs were more enriched in 13C and had CH4/C2+ < 103, suggesting a mixture of microbial and non-microbial methane. The concentrations of aromatic compounds, and ethane, propane, iso- and n-butane were well described by simple physical mixing between the aromatic- and alkane-poor, shallow groundwater and the relatively aromatic, and alkane-rich groundwater that flows through both the peridotite and the FSC suggesting that these aromatic and alkane compounds originated in the deeper FSC groundwater and are not produced in the shallow peridotite-only groundwater. The aromatic compounds most probably originated from the diagenesis/degradation of organic matter in the marine sediments below the peridotite body, while the gaseous alkanes may have multiple sources including thermal degradation of the organic matter in the marine sediments below the peridotite body and possibly by abiogenic reactions occurring within the peridotite body. This geochemical study demonstrates the complexity of The Cedars, and the possible sources of hydrocarbons at continental sites of serpentinization.

Propulsion via flexible flapping in granular media

NASA Astrophysics Data System (ADS)

Peng, Zhiwei; Ding, Yang; Pietrzyk, Kyle; Elfring, Gwynn; Pak, On Shun

2017-11-01

Biological locomotion in nature is often achieved by the interaction between a flexible body and its surrounding medium. The interaction of a flexible body with granular media is less understood compared with viscous fluids partially due to its complex rheological properties. In this work, we explore the effect of flexibility on granular propulsion by considering a simple mechanical model in which a rigid rod is connected to a torsional spring that is under a displacement actuation using a granular resistive force theory. Through a combined numerical and asymptotic investigation, we characterize the propulsive dynamics of such a flexible flapper in relation to the actuation amplitude and spring stiffness, and we compare these dynamics with those observed in a viscous fluid. In addition, we demonstrate that the maximum possible propulsive force can be obtained in the steady propulsion limit with a finite spring stiffness and large actuation amplitude. These results may apply to the development of synthetic locomotive systems that exploit flexibility to move through complex terrestrial media. Funding for Z.P. and Y.D. was partially provided by NSFC 394 Grant No. 11672029 and NSAF-NSFC Grant No. U1530401.

Development of body weight support gait training system using antagonistic bi-articular muscle model.

PubMed

Shibata, Yoshiyuki; Imai, Shingo; Nobutomo, Tatsuya; Miyoshi, Tasuku; Yamamoto, Shin-Ichiroh

2010-01-01

The purpose of this study is to develop a body weight support gait training system for stroke and spinal cord injury. This system consists of a powered orthosis, treadmill and equipment of body weight support. Attachment of the powered orthosis is able to fit subject who has difference of body size. This powered orthosis is driven by pneumatic McKibben actuator. Actuators are arranged as pair of antagonistic bi-articular muscle model and two pairs of antagonistic mono-articular muscle model like human musculoskeletal system. Part of the equipment of body weight support suspend subject by wire harness, and body weight of subject is supported continuously by counter weight. The powered orthosis is attached equipment of body weight support by parallel linkage, and movement of the powered orthosis is limited at sagittal plane. Weight of the powered orthosis is compensated by parallel linkage with gas-spring. In this study, we developed system that has orthosis powered by pneumatic McKibben actuators and equipment of body weight support. We report detail of our developed body weight support gait training system.

Adult survival, apparent lamb survival, and body condition of desert bighorn sheep in relation to habitat and precipitation on the Kofa National Wildlife Refuge, Arizona

USGS Publications Warehouse

Overstreet, Matthew; Caldwell, Colleen A.; Cain, James W.

2014-01-01

The decline of desert bighorn sheep on the Kofa National Wildlife Refuge (KNWR) beginning in 2003 stimulated efforts to determine the factors limiting survival and recruitment. We 1) determined pregnancy rates, body fat, and estimated survival rates of adults and lambs; 2) investigated the relationship between precipitation, forage conditions, previous year’s reproductive success, and adult body condition; 3) assessed the relative influence of body condition of adult females, precipitation, and forage characteristics on apparent survival of lambs; and 4) determined the prevalence of disease. To assess the influence of potential limiting factors on female desert bighorn sheep on the KNWR, we modeled percent body fat of adult females as a function of previous year’s reproductive effort, age class, and forage conditions (i.e., seasonal NDVI and seasonal precipitation). In addition, we assessed the relative influence of the body condition of adult females, precipitation, and forage conditions (NDVI) on length of time a lamb was observed at heel.Adult female survival was high in both 2009 (0.90 [SE = 0.05]) and 2010 (0.96 [SE = 0.03]). Apparent lamb survival to 6 months of age was 0.23 (SE = 0.05) during 2009-2010 and 0.21 (SE = 0.05) during 2010-2011 lambing seasons. Mean body fat for adult females was 12.03% (SE = 0.479) in 2009-2010 and 11.11% (SE= 0.486) in 2010-2011 and was not significantly different between years. Pregnancy rate was 100% in 2009 and 97.5% in 2010.Models containing the previous year’s reproductive effort, spring NDVI and previous year’s reproductive effort and spring precipitation best approximated data on percent body fat in adult females in 2009-2010. In 2010-2011, the two highest-ranking models included the previous year’s reproductive effort and winter NDVI and previous year’s reproductive effort, and winter and spring NDVI. None of the models assessing the influence of maternal body fat, precipitation, or forage conditions were particularly useful for predicting apparent lamb survival.The high pregnancy rates and body fat levels in excess of 11% do not indicate that this population of desert bighorn was nutritionally stressed during our study and are thus likely not contributing to the low lamb survival estimates we observed. However, body condition data during the population decline is not available and whether this population was nutritionally limited during the initial population decline remains unknown.The prevalence of disease in the Kofa herd may be a limiting factor; however, due to a lack of disease monitoring during the population decline it is uncertain if disease contributed to the decline. Further research is needed to fully understand the complex interaction of disease in this population at the individual and population level and determine to what extent disease predisposes individuals to predation or other causes of mortality.

Reconstruction of equilibrium trajectories during whole-body movements.

PubMed

Domen, K; Latash, M L; Zatsiorsky, V M

1999-03-01

The framework of the equilibrium-point hypothesis was used to reconstruct equilibrium trajectories (ETs) of the ankle, hip and body center of mass during quick voluntary hip flexions ('Japanese courtesy bow') by standing subjects. Different spring loads applied to the subject's back were used to introduce smooth perturbations that are necessary to reconstruct ETs based on a series of trials at the same task. Time patterns of muscle torques were calculated using inverse dynamics techniques. A second-order linear model was employed to calculate the instantaneous position of the spring-like joint or center of mass characteristic at different times during the movement. ETs of the joints and of the center of mass had significantly different shapes from the actual trajectories. Integral measures of electromyographic bursts of activity in postural muscles demonstrated a relation to muscle length corresponding to the equilibrium-point hypothesis.

Contact dynamics math model

NASA Technical Reports Server (NTRS)

Glaese, John R.; Tobbe, Patrick A.

1986-01-01

The Space Station Mechanism Test Bed consists of a hydraulically driven, computer controlled six degree of freedom (DOF) motion system with which docking, berthing, and other mechanisms can be evaluated. Measured contact forces and moments are provided to the simulation host computer to enable representation of orbital contact dynamics. This report describes the development of a generalized math model which represents the relative motion between two rigid orbiting vehicles. The model allows motion in six DOF for each body, with no vehicle size limitation. The rotational and translational equations of motion are derived. The method used to transform the forces and moments from the sensor location to the vehicles' centers of mass is also explained. Two math models of docking mechanisms, a simple translational spring and the Remote Manipulator System end effector, are presented along with simulation results. The translational spring model is used in an attempt to verify the simulation with compensated hardware in the loop results.

46 CFR 162.018-4 - Construction and workmanship.

Code of Federal Regulations, 2011 CFR

2011-10-01

... external spring-loaded type, suitable for the intended service. (b) Safety relief valve body, base, bonnet... with side or top outlet discharge connections. (f)(1) Springs shall not show a permanent set exceeding... the spring solid. (2) Springs may not be re-set for any pressure more than 10 percent above or 10...

46 CFR 162.018-4 - Construction and workmanship.

Code of Federal Regulations, 2012 CFR

2012-10-01

... external spring-loaded type, suitable for the intended service. (b) Safety relief valve body, base, bonnet... with side or top outlet discharge connections. (f)(1) Springs shall not show a permanent set exceeding... the spring solid. (2) Springs may not be re-set for any pressure more than 10 percent above or 10...

46 CFR 162.018-4 - Construction and workmanship.

Code of Federal Regulations, 2010 CFR

2010-10-01

... external spring-loaded type, suitable for the intended service. (b) Safety relief valve body, base, bonnet... with side or top outlet discharge connections. (f)(1) Springs shall not show a permanent set exceeding... the spring solid. (2) Springs may not be re-set for any pressure more than 10 percent above or 10...

46 CFR 162.018-4 - Construction and workmanship.

Code of Federal Regulations, 2013 CFR

2013-10-01

... external spring-loaded type, suitable for the intended service. (b) Safety relief valve body, base, bonnet... with side or top outlet discharge connections. (f)(1) Springs shall not show a permanent set exceeding... the spring solid. (2) Springs may not be re-set for any pressure more than 10 percent above or 10...

46 CFR 162.018-4 - Construction and workmanship.

Code of Federal Regulations, 2014 CFR

2014-10-01

... external spring-loaded type, suitable for the intended service. (b) Safety relief valve body, base, bonnet... with side or top outlet discharge connections. (f)(1) Springs shall not show a permanent set exceeding... the spring solid. (2) Springs may not be re-set for any pressure more than 10 percent above or 10...

Modeling meniscus rise in capillary tubes using fluid in rigid-body motion approach

NASA Astrophysics Data System (ADS)

Hamdan, Mohammad O.; Abu-Nabah, Bassam A.

2018-04-01

In this study, a new term representing net flux rate of linear momentum is introduced to Lucas-Washburn equation. Following a fluid in rigid-body motion in modeling the meniscus rise in vertical capillary tubes transforms the nonlinear Lucas-Washburn equation to a linear mass-spring-damper system. The linear nature of mass-spring-damper system with constant coefficients offers a nondimensional analytical solution where meniscus dynamics are dictated by two parameters, namely the system damping ratio and its natural frequency. This connects the numerous fluid-surface interaction physical and geometrical properties to rather two nondimensional parameters, which capture the underlying physics of meniscus dynamics in three distinct cases, namely overdamped, critically damped, and underdamped systems. Based on experimental data available in the literature and the understanding meniscus dynamics, the proposed model brings a new approach of understanding the system initial conditions. Accordingly, a closed form relation is produced for the imbibition velocity, which equals half of the Bosanquet velocity divided by the damping ratio. The proposed general analytical model is ideal for overdamped and critically damped systems. While for underdamped systems, the solution shows fair agreement with experimental measurements once the effective viscosity is determined. Moreover, the presented model shows meniscus oscillations around equilibrium height occur if the damping ratio is less than one.

Identification and experimental validation of damping ratios of different human body segments through anthropometric vibratory model in standing posture.

PubMed

Gupta, T C

2007-08-01

A 15 degrees of freedom lumped parameter vibratory model of human body is developed, for vertical mode vibrations, using anthropometric data of the 50th percentile US male. The mass and stiffness of various segments are determined from the elastic modulii of bones and tissues and from the anthropometric data available, assuming the shape of all the segments is ellipsoidal. The damping ratio of each segment is estimated on the basis of the physical structure of the body in a particular posture. Damping constants of various segments are calculated from these damping ratios. The human body is modeled as a linear spring-mass-damper system. The optimal values of the damping ratios of the body segments are estimated, for the 15 degrees of freedom model of the 50th percentile US male, by comparing the response of the model with the experimental response. Formulating a similar vibratory model of the 50th percentile Indian male and comparing the frequency response of the model with the experimental response of the same group of subjects validate the modeling procedure. A range of damping ratios has been considered to develop a vibratory model, which can predict the vertical harmonic response of the human body.

A novel compact compliant actuator design for rehabilitation robots.

PubMed

Yu, Haoyong; Huang, Sunan; Thakor, Nitish V; Chen, Gong; Toh, Siew-Lok; Sta Cruz, Manolo; Ghorbel, Yassine; Zhu, Chi

2013-06-01

Rehabilitation robots have direct physical interaction with human body. Ideally, actuators for rehabilitation robots should be compliant, force controllable, and back drivable due to safety and control considerations. Various designs of Series Elastic Actuators (SEA) have been developed for these applications. However, current SEA designs face a common performance limitation due to the compromise on the spring stiffness selection. This paper presents a novel compact compliant force control actuator design for portable rehabilitation robots to overcome the performance limitations in current SEAs. Our design consists of a servomotor, a ball screw, a torsional spring between the motor and the ball screw, and a set of translational springs between the ball screw nut and the external load. The soft translational springs are used to handle the low force operation and reduce output impedance, stiction, and external shock load. The torsional spring, being in the high speed range, has high effective stiffness and improves the system bandwidth in large force operation when the translational springs are fully compressed. This design is also more compact due to the smaller size of the springs. We explain the construction and the working principle of our new design, followed by the dynamic modeling and analysis of the actuator. We also show the preliminary testing results of a prototype actuator designed for a lower limb exoskeleton for gait rehabilitation.

Retrieval of bronchial foreign body with central lumen using a flexible bronchoscope.

PubMed

Wong, Kin-Sun; Lai, Shen-Hao; Lien, Reyin; Hsia, Shao-Hsuan

2002-02-25

A 5 year-old boy aspirated a metal spring accidentally. The right bronchial foreign body was removed by threading the alligator of a biopsy forceps through the lumen of the spring while opening its jaws distally. This case illustrates that a foreign body with a central lumen in a child can be successfully removed using a flexible bronchoscope, thus obviating the need for general anesthesia and rigid bronchoscopy.

Design and Construction of a Small Whole Body Inhalation Chamber

DTIC Science & Technology

2010-07-30

by 12 7/8 inch high) were solvent welded onto this base using Weldon 4 (Ridout Plastics, San Diego CA). On the inside of each side wall a 2 inch...together using one inch spring clamps (Just Clamps, model 616,Atlanta Ga) on their respective flanges. These clamps were spaced evenly around the

Implementation of the glacial rebound prestress advection correction in general-purpose finite element analysis software: Springs versus foundations

NASA Astrophysics Data System (ADS)

Schmidt, Peter; Lund, Björn; Hieronymus, Christoph

2012-03-01

When general-purpose finite element analysis software is used to model glacial isostatic adjustment (GIA), the first-order effect of prestress advection has to be accounted for by the user. We show here that the common use of elastic foundations at boundaries between materials of different densities will produce incorrect displacements, unless the boundary is perpendicular to the direction of gravity. This is due to the foundations always acting perpendicular to the surface to which they are attached, while the body force they represent always acts in the direction of gravity. If prestress advection is instead accounted for by the use of elastic spring elements in the direction of gravity, the representation will be correct. The use of springs adds a computation of the spring constants to the analysis. The spring constant for a particular node is defined by the product of the density contrast at the boundary, the gravitational acceleration, and the area supported by the node. To be consistent with the finite element formulation, the area is evaluated by integration of the nodal shape functions. We outline an algorithm for the calculation and include a Python script that integrates the shape functions over a bilinear quadrilateral element. For linear rectangular and triangular elements, the area supported by each node is equal to the element area divided the number of defining nodes, thereby simplifying the computation. This is, however, not true in the general nonrectangular case, and we demonstrate this with a simple 1-element model. The spring constant calculation is simple and performed in the preprocessing stage of the analysis. The time spent on the calculation is more than compensated for by a shorter analysis time, compared to that for a model with foundations. We illustrate the effects of using springs versus foundations with a simple two-dimensional GIA model of glacial loading, where the Earth model has an inclined boundary between the overlying elastic layer and the lower viscoelastic layer. Our example shows that the error introduced by the use of foundations is large enough to affect an analysis based on high-accuracy geodetic data.

Physiological status of naturally reared juvenile spring chinook salmon in the Yakima River: Seasonal dynamics and changes associated with smolting

USGS Publications Warehouse

Beckman, B.R.; Larsen, D.A.; Sharpe, C.; Lee-Pawlak, B.; Schreck, C.B.; Dickhoff, Walton W.

2000-01-01

Two year-classes of juvenile spring chinook salmon Oncorhynchus tshawytscha from the Yakima River, Washington, were sampled from July (3-4 months postemergence) through May (yearling smolt out-migration). Physiological characters measured included liver glycogen, body lipid, gill Na+-K+ ATPase, plasma thyroxine (T4), and plasma insulin-like growth factor-I (IGF-I). Distinct physiological changes were found that corresponded to season. Summer and fall were characterized by relatively high body lipid and condition factor. Winter was characterized by decreases in body lipid, condition factor, and plasma hormones. An increase in condition factor and body lipid was found in February and March. Finally, April and May were characterized by dramatic changes characteristic of smolting, including increased gill Na+-K+ ATPase activity, plasma T4, and IGF-I and decreased condition factor, body lipid, and liver glycogen. These results create a physiological template for juvenile spring chinook salmon in the drainage that provides a baseline for comparison with other years, populations, and life history types. In addition, this baseline provides a standard for controlled laboratory experiments and a target for fish culturists who rear juvenile spring chinook salmon for release from conservation hatcheries. The implications of these results for juvenile chinook salmon ecology and life history are discussed.

Thermal springs of Malaysia and their potentialdevelopment

NASA Astrophysics Data System (ADS)

Rahim Samsudin, Abdul; Hamzah, Umar; Rahman, Rakmi Ab.; Siwar, Chamhuri; Fauzi Mohd. Jani, Mohd; Othman, Redzuan

The study on the potential development of hot springs for the tourism industry in Malaysiawas conducted. Out of the 40 hot springs covered, the study identified 9 hot springs having a high potential for development, 14 having medium potential and the remaining 17 having low or least potential for development. This conclusion was arrived at after considering the technical and economic feasibility of the various hot springs. Technical feasibility criteria includes geological factors, water quality, temperature and flow rate. The economic feasibility criteria considers measures such as accessibility, current and market potentials in terms of visitors, surrounding attractions and existing inventory and facilities available. A geological input indicates that high potential hot springs are located close to or within the granite body and associated with major permeable fault zones. They normally occur at low elevation adjacent to topographic highs. High potential hot springs are also characterised by high water temperature, substantial flowrate and very good water quality which is important for water-body contact activities such as soaking. Economic criteria for high potential hot springs are associated with good accessibility, good market, good surrounding attractions like rural and village setting and well developed facilities and infrastructures.

The impact of post-exercise hydration with deep-ocean mineral water on rehydration and exercise performance.

PubMed

Keen, Douglas A; Constantopoulos, Eleni; Konhilas, John P

2016-01-01

Dehydration caused by prolonged exercise impairs thermoregulation, endurance and exercise performance. Evidence from animal and human studies validates the potential of desalinated deep-ocean mineral water to positively impact physiological and pathophysiological conditions. Here, we hypothesize that deep-ocean mineral water drawn from a depth of 915 m off the Kona, HI coast enhances recovery of hydration and exercise performance following a dehydrating exercise protocol compared to mountain spring water and a carbohydrate-based sports drink. Subjects (n = 8) were exposed to an exercise-dehydration protocol (stationary biking) under warm conditions (30 °C) to achieve a body mass loss of 3 % (93.4 ± 21.7 total exercise time). During the post-exercise recovery period, subjects received deep-ocean mineral water (Kona), mountain spring water (Spring) or a carbohydrate-based sports drink (Sports) at a volume (in L) equivalent to body mass loss (in Kg). Salivary samples were collected at regular intervals during exercise and post-exercise rehydration. Additionally, each participant performed peak torque knee extension as a measure of lower body muscle performance. Subjects who received Kona during the rehydrating period showed a significantly more rapid return to pre-exercise (baseline) hydration state, measured as the rate of decline in peak to baseline salivary osmolality, compared to Sports and Spring groups. In addition, subjects demonstrated significantly improved recovery of lower body muscle performance following rehydration with Kona versus Sports or Spring groups. Deep-ocean mineral water shows promise as an optimal rehydrating source over spring water and/or sports drink.

A piecewise mass-spring-damper model of the human breast.

PubMed

Cai, Yiqing; Chen, Lihua; Yu, Winnie; Zhou, Jie; Wan, Frances; Suh, Minyoung; Chow, Daniel Hung-Kay

2018-01-23

Previous models to predict breast movement whilst performing physical activities have, erroneously, assumed uniform elasticity within the breast. Consequently, the predicted displacements have not yet been satisfactorily validated. In this study, real time motion capture of the natural vibrations of a breast that followed, after raising and allowing it to fall freely, revealed an obvious difference in the vibration characteristics above and below the static equilibrium position. This implied that the elastic and viscous damping properties of a breast could vary under extension or compression. Therefore, a new piecewise mass-spring-damper model of a breast was developed with theoretical equations to derive values for its spring constants and damping coefficients from free-falling breast experiments. The effective breast mass was estimated from the breast volume extracted from a 3D body scanned image. The derived spring constant (k a  = 73.5 N m -1 ) above the static equilibrium position was significantly smaller than that below it (k b  = 658 N m -1 ), whereas the respective damping coefficients were similar (c a  = 1.83 N s m -1 , c b  = 2.07 N s m -1 ). These values were used to predict the nipple displacement during bare-breasted running for validation. The predicted and experimental results had a 2.6% or less root-mean-square-error of the theoretical and experimental amplitudes, so the piecewise mass-spring-damper model and equations were considered to have been successfully validated. This provides a theoretical basis for further research into the dynamic, nonlinear viscoelastic properties of different breasts and the prediction of external forces for the necessary breast support during different sports activities. Copyright © 2017 Elsevier Ltd. All rights reserved.

Water quality observations of ice-covered, stagnant, eutrophic water bodies and analysis of influence of ice-covered period on water quality

NASA Astrophysics Data System (ADS)

sugihara, K.; Nakatsugawa, M.

2013-12-01

The water quality characteristics of ice-covered, stagnant, eutrophic water bodies have not been clarified because of insufficient observations. It has been pointed out that climate change has been shortening the duration of ice-cover; however, the influence of climate change on water quality has not been clarified. This study clarifies the water quality characteristics of stagnant, eutrophic water bodies that freeze in winter, based on our surveys and simulations, and examines how climate change may influence those characteristics. We made fixed-point observation using self-registering equipment and vertical water sampling. Self-registering equipment measured water temperature and dissolved oxygen(DO).vertical water sampling analyzed biological oxygen demand(BOD), total nitrogen(T-N), nitrate nitrogen(NO3-N), nitrite nitrogen(NO2-N), ammonium nitrogen(NH4-N), total phosphorus(TP), orthophosphoric phosphorus(PO4-P) and chlorophyll-a(Chl-a). The survey found that climate-change-related increases in water temperature were suppressed by ice covering the water area, which also blocked oxygen supply. It was also clarified that the bottom sediment consumed oxygen and turned the water layers anaerobic beginning from the bottom layer, and that nutrient salts eluted from the bottom sediment. The eluted nutrient salts were stored in the water body until the ice melted. The ice-covered period of water bodies has been shortening, a finding based on the analysis of weather and water quality data from 1998 to 2008. Climate change was surveyed as having caused decreases in nutrient salts concentration because of the shortened ice-covered period. However, BOD in spring showed a tendency to increase because of the proliferation of phytoplankton that was promoted by the climate-change-related increase in water temperature. To forecast the water quality by using these findings, particularly the influence of climate change, we constructed a water quality simulation model that incorporates the freezing-over of water bodies. The constructed model shows good temporal and spatial reproducibility and enables water quality to be forecast throughout the year, including during the ice-covered period. The forecasts using the model agree well with the survey results of shortened ice period and climate-change-related increase in the BOD in spring. From the result of calculations and observations, it is suggested that water quality of spring has been deteriorate because of freezing period to be shortened due to temperature rising.

Partitioning the Metabolic Cost of Human Running: A Task-by-Task Approach

PubMed Central

Arellano, Christopher J.; Kram, Rodger

2014-01-01

Compared with other species, humans can be very tractable and thus an ideal “model system” for investigating the metabolic cost of locomotion. Here, we review the biomechanical basis for the metabolic cost of running. Running has been historically modeled as a simple spring-mass system whereby the leg acts as a linear spring, storing, and returning elastic potential energy during stance. However, if running can be modeled as a simple spring-mass system with the underlying assumption of perfect elastic energy storage and return, why does running incur a metabolic cost at all? In 1980, Taylor et al. proposed the “cost of generating force” hypothesis, which was based on the idea that elastic structures allow the muscles to transform metabolic energy into force, and not necessarily mechanical work. In 1990, Kram and Taylor then provided a more explicit and quantitative explanation by demonstrating that the rate of metabolic energy consumption is proportional to body weight and inversely proportional to the time of foot-ground contact for a variety of animals ranging in size and running speed. With a focus on humans, Kram and his colleagues then adopted a task-by-task approach and initially found that the metabolic cost of running could be “individually” partitioned into body weight support (74%), propulsion (37%), and leg-swing (20%). Summing all these biomechanical tasks leads to a paradoxical overestimation of 131%. To further elucidate the possible interactions between these tasks, later studies quantified the reductions in metabolic cost in response to synergistic combinations of body weight support, aiding horizontal forces, and leg-swing-assist forces. This synergistic approach revealed that the interactive nature of body weight support and forward propulsion comprises ∼80% of the net metabolic cost of running. The task of leg-swing at most comprises ∼7% of the net metabolic cost of running and is independent of body weight support and forward propulsion. In our recent experiments, we have continued to refine this task-by-task approach, demonstrating that maintaining lateral balance comprises only 2% of the net metabolic cost of running. In contrast, arm-swing reduces the cost by ∼3%, indicating a net metabolic benefit. Thus, by considering the synergistic nature of body weight support and forward propulsion, as well as the tasks of leg-swing and lateral balance, we can account for 89% of the net metabolic cost of human running. PMID:24838747

Partitioning the metabolic cost of human running: a task-by-task approach.

PubMed

Arellano, Christopher J; Kram, Rodger

2014-12-01

Compared with other species, humans can be very tractable and thus an ideal "model system" for investigating the metabolic cost of locomotion. Here, we review the biomechanical basis for the metabolic cost of running. Running has been historically modeled as a simple spring-mass system whereby the leg acts as a linear spring, storing, and returning elastic potential energy during stance. However, if running can be modeled as a simple spring-mass system with the underlying assumption of perfect elastic energy storage and return, why does running incur a metabolic cost at all? In 1980, Taylor et al. proposed the "cost of generating force" hypothesis, which was based on the idea that elastic structures allow the muscles to transform metabolic energy into force, and not necessarily mechanical work. In 1990, Kram and Taylor then provided a more explicit and quantitative explanation by demonstrating that the rate of metabolic energy consumption is proportional to body weight and inversely proportional to the time of foot-ground contact for a variety of animals ranging in size and running speed. With a focus on humans, Kram and his colleagues then adopted a task-by-task approach and initially found that the metabolic cost of running could be "individually" partitioned into body weight support (74%), propulsion (37%), and leg-swing (20%). Summing all these biomechanical tasks leads to a paradoxical overestimation of 131%. To further elucidate the possible interactions between these tasks, later studies quantified the reductions in metabolic cost in response to synergistic combinations of body weight support, aiding horizontal forces, and leg-swing-assist forces. This synergistic approach revealed that the interactive nature of body weight support and forward propulsion comprises ∼80% of the net metabolic cost of running. The task of leg-swing at most comprises ∼7% of the net metabolic cost of running and is independent of body weight support and forward propulsion. In our recent experiments, we have continued to refine this task-by-task approach, demonstrating that maintaining lateral balance comprises only 2% of the net metabolic cost of running. In contrast, arm-swing reduces the cost by ∼3%, indicating a net metabolic benefit. Thus, by considering the synergistic nature of body weight support and forward propulsion, as well as the tasks of leg-swing and lateral balance, we can account for 89% of the net metabolic cost of human running. © The Author 2014. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

Modelling of human walking to optimise the function of ankle-foot orthosis in Guillan-Barré patients with drop foot.

PubMed

Jamshidi, N; Rostami, M; Najarian, S; Menhaj, M B; Saadatnia, M; Firooz, S

2009-04-01

This paper deals with the dynamic modelling of human walking. The main focus of this research was to optimise the function of the orthosis in patients with neuropathic feet, based on the kinematics data from different categories of neuropathic patients. The patient's body on the sagittal plane was modelled for calculating the torques generated in joints. The kinematics data required for mathematical modelling of the patients were obtained from the films of patients captured by high speed camera, and then the films were analysed through a motion analysis software. An inverse dynamic model was used for estimating the spring coefficient. In our dynamic model, the role of muscles was substituted by adding a spring-damper between the shank and ankle that could compensate for their weakness by designing ankle-foot orthoses based on the kinematics data obtained from the patients. The torque generated in the ankle was varied by changing the spring constant. Therefore, it was possible to decrease the torque generated in muscles which could lead to the design of more comfortable and efficient orthoses. In this research, unlike previous research activities, instead of studying the abnormal gait or modelling the ankle-foot orthosis separately, the function of the ankle-foot orthosis on the abnormal gait has been quantitatively improved through a correction of the torque.

Investigations of the effects of particle properties on the wear resistance of the particle reinforced composites using a novel wear model

NASA Astrophysics Data System (ADS)

Prabhu, T. Ram

2016-08-01

A wear model is developed based on the discrete lattice spring-mass approach to study the effects of particle volume fraction, size, and stiffness on the wear resistance of particle reinforced composites. To study these effects, we have considered three volume fractions (10%, 20% and 30%), two sizes (10 × 10 and 4 × 4 sites), and two different stiffness of particles embedded in the matrix in a regular pattern. In this model, we have discretized the composite system (400 × 100 sites) into the lumped masses connected with interaction spring elements in two dimensions. The interaction elements are assumed as linear elastic and ideal plastic under applied forces. Each mass is connected to its first and second nearest neighbors by springs. The matrix and particles sites are differentiated by choosing the different stiffness values. The counter surface is simulated as a rigid body that moves on the composite material at a constant sliding speed along the horizontal direction. The governing equations are formed by equating the spring force between the pair of sites given by Hooke’s law plus external contact forces and the force due to the motion of the site given by the equation of motion. The equations are solved for the plastic strain accumulated in the springs using an explicit time stepping procedure based on a finite difference form of the above equations. If the total strain accumulated in the spring elements connected to a lump mass site exceeds the failure strain, the springs are considered to be broken, and the mass site is removed or worn away from the lattice and accounts as a wear loss. The model predicts that (i) increasing volume fraction, reducing particle size and increasing particle stiffness enhance the wear resistance of the particle reinforced composites, (ii) the particle stiffness is the most significant factor affecting the wear resistance of the composites, and (iii) the wear resistance reduced above the critical volume fraction (Vc), and Vc increases with increasing particle size. Finally, we have qualitatively compared the model results with our previously published experimental results to prove the effectiveness of the model to analysis the complex wear systems.

Low-Reynolds-number predator.

PubMed

Ebrahimian, Mehran; Yekehzare, Mohammad; Ejtehadi, Mohammad Reza

2015-12-01

To generalize simple bead-linker model of swimmers to higher dimensions and to demonstrate the chemotaxis ability of such swimmers, here we introduce a low-Reynolds predator, using a two-dimensional triangular bead-spring model. Two-state linkers as mechanochemical enzymes expand as a result of interaction with particular activator substances in the environment, causing the whole body to translate and rotate. The concentration of the chemical stimulator controls expansion versus the contraction rate of each arm and so affects the ability of the body for diffusive movements; also the variation of activator substance's concentration in the environment breaks the symmetry of linkers' preferred state, resulting in the drift of the random walker along the gradient of the density of activators. External food or danger sources may attract or repel the body by producing or consuming the chemical activators of the organism's enzymes, inducing chemotaxis behavior. Generalization of the model to three dimensions is straightforward.

Low-Reynolds-number predator

NASA Astrophysics Data System (ADS)

Ebrahimian, Mehran; Yekehzare, Mohammad; Ejtehadi, Mohammad Reza

2015-12-01

To generalize simple bead-linker model of swimmers to higher dimensions and to demonstrate the chemotaxis ability of such swimmers, here we introduce a low-Reynolds predator, using a two-dimensional triangular bead-spring model. Two-state linkers as mechanochemical enzymes expand as a result of interaction with particular activator substances in the environment, causing the whole body to translate and rotate. The concentration of the chemical stimulator controls expansion versus the contraction rate of each arm and so affects the ability of the body for diffusive movements; also the variation of activator substance's concentration in the environment breaks the symmetry of linkers' preferred state, resulting in the drift of the random walker along the gradient of the density of activators. External food or danger sources may attract or repel the body by producing or consuming the chemical activators of the organism's enzymes, inducing chemotaxis behavior. Generalization of the model to three dimensions is straightforward.

Normal Modes of Vibration of the PHALANX Gun

DTIC Science & Technology

1993-06-01

Clamps Bricks, Thin Shells, Rigid Elements Mid-Barrel Clamps Bricks, Rigid Elements Barrels Beams with tubular cross-section Stub Rotor Bricks, Thin...Shells Rotor Bricks Needle Bearing Bricks, Springs Casing Thin Shells Thrust Bearing Bricks, Springs Recoil Adapters Bricks, Rigid Elements, Springs... rigid elements were used to connect the barrels to the clamps and stub rotor and the recoil adapter springs to 48 the gun body. "End release codes

Functional analysis of Normalized Difference Vegetation Index curves reveals overwinter mule deer survival is driven by both spring and autumn phenology

PubMed Central

Hurley, Mark A.; Hebblewhite, Mark; Gaillard, Jean-Michel; Dray, Stéphane; Taylor, Kyle A.; Smith, W. K.; Zager, Pete; Bonenfant, Christophe

2014-01-01

Large herbivore populations respond strongly to remotely sensed measures of primary productivity. Whereas most studies in seasonal environments have focused on the effects of spring plant phenology on juvenile survival, recent studies demonstrated that autumn nutrition also plays a crucial role. We tested for both direct and indirect (through body mass) effects of spring and autumn phenology on winter survival of 2315 mule deer fawns across a wide range of environmental conditions in Idaho, USA. We first performed a functional analysis that identified spring and autumn as the key periods for structuring the among-population and among-year variation of primary production (approximated from 1 km Advanced Very High Resolution Radiometer Normalized Difference Vegetation Index (NDVI)) along the growing season. A path analysis showed that early winter precipitation and direct and indirect effects of spring and autumn NDVI functional components accounted for 45% of observed variation in overwinter survival. The effect size of autumn phenology on body mass was about twice that of spring phenology, while direct effects of phenology on survival were similar between spring and autumn. We demonstrate that the effects of plant phenology vary across ecosystems, and that in semi-arid systems, autumn may be more important than spring for overwinter survival. PMID:24733951

Modeling of Spinal Column of Seated Human Body under Exposure to Whole-Body Vibration

NASA Astrophysics Data System (ADS)

Tamaoki, Gen; Yoshimura, Takuya; Kuriyama, Kaoru; Nakai, Kazuma

In vehicle systems occupational drivers might expose themselves to vibration for a long time. This may cause illness of the spinal column such as low back pain. Therefore, it is necessary to evaluate the influence of vibration to the spinal column. Thus the modeling of seated human body is conducted in order to evaluate the effect of whole-body vibration to the spinal column. This model has the spinal column and the support structures such as the muscles of the back and the abdomen. The spinal column is made by the vertebrae and the intervertebral disks that are considered the rigid body and the rotational spring and damper respectively. The parameter of this model is decided by the literature and the body type of the subject with respect to the mass and the model structure. And stiffness and damping parameters are searched by fitting the model simulation results to the experimental measured data with respect to the vibration transmissibilities from the seat surface to the spinal column and the head and with respect to the driving-point apparent mass. In addition, the natural modes of the model compare with the result of experimental modal analysis. The influence of the abdomen and the muscles of the back are investigated by comparing three models with respect to above vibration characteristics. Three model are the proposed model, the model that has the spinal column and the model that has the muscles of the back in addition to the spinal column.

Walking model with no energy cost.

PubMed

Gomes, Mario; Ruina, Andy

2011-03-01

We have numerically found periodic collisionless motions of a walking model consisting of linked rigid objects. Unlike previous designs, this model can walk on level ground at noninfinitesimal speed with zero energy input. The model avoids collisional losses by using an internal mode of oscillation: swaying of the upper body coupled to the legs by springs. Appropriate synchronized internal oscillations set the foot-strike collision to zero velocity. The concept might be of use for energy-efficient robots and may also help to explain aspects of human and animal locomotion efficiency.

MPPhys—A many-particle simulation package for computational physics education

NASA Astrophysics Data System (ADS)

Müller, Thomas

2014-03-01

In a first course to classical mechanics elementary physical processes like elastic two-body collisions, the mass-spring model, or the gravitational two-body problem are discussed in detail. The continuation to many-body systems, however, is deferred to graduate courses although the underlying equations of motion are essentially the same and although there is a strong motivation for high-school students in particular because of the use of particle systems in computer games. The missing link between the simple and the more complex problem is a basic introduction to solve the equations of motion numerically which could be illustrated, however, by means of the Euler method. The many-particle physics simulation package MPPhys offers a platform to experiment with simple particle simulations. The aim is to give a principle idea how to implement many-particle simulations and how simulation and visualization can be combined for interactive visual explorations. Catalogue identifier: AERR_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AERR_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 111327 No. of bytes in distributed program, including test data, etc.: 608411 Distribution format: tar.gz Programming language: C++, OpenGL, GLSL, OpenCL. Computer: Linux and Windows platforms with OpenGL support. Operating system: Linux and Windows. RAM: Source Code 4.5 MB Complete package 242 MB Classification: 14, 16.9. External routines: OpenGL, OpenCL Nature of problem: Integrate N-body simulations, mass-spring models Solution method: Numerical integration of N-body-simulations, 3D-Rendering via OpenGL. Running time: Problem dependent

Intermittent fasting during winter and spring affects body composition and reproduction of a migratory duck

USGS Publications Warehouse

Barboza, P.S.; Jorde, Dennis G.

2002-01-01

We compared food intake, body mass and body composition of male and female black ducks (Anas rubripes) during winter (January-March). Birds were fed the same complete diet ad libitum on consecutive days each week without fasting (control; nine male; nine female) or with either short fasts (2 day.week-1; nine male; nine female), or long fasts (4 day.week-1; eleven male; twelve female). We continued treatments through spring (March-May) to measure the effect of intermittent fasts on body mass and egg production. Daily food intake of fasted birds was up to four times that of unfasted birds. Weekly food intake of males was similar among treatments (364 g.kg-1.week-1) but fasted females consumed more than unfasted females in January (363 g.kg-1.week-1 vs. 225 g.kg-1.week-1). Although both sexes lost 10-14% body mass, fasted females lost less mass and lipid than unfasted females during winter. Total body nitrogen was conserved over winter in both sexes even though the heart and spleen lost mass while the reproductive tract and liver gained mass. Intermittent fasting increased liver, intestinal tissue and digesta mass of females but not of males. Fasting delayed egg production in spring but did not affect size, fertility or hatching of the clutch. Females on long fasts were still heavier than controls after laying eggs. Thus black ducks combine flexibility of food intake with plasticity of digestive tract, liver and adipose tissue when food supply is interrupted during winter. Females modulate body mass for survival and defer reproduction when food supply is interrupted in spring.

Coarse-Grained Structural Modeling of Molecular Motors Using Multibody Dynamics

PubMed Central

Parker, David; Bryant, Zev; Delp, Scott L.

2010-01-01

Experimental and computational approaches are needed to uncover the mechanisms by which molecular motors convert chemical energy into mechanical work. In this article, we describe methods and software to generate structurally realistic models of molecular motor conformations compatible with experimental data from different sources. Coarse-grained models of molecular structures are constructed by combining groups of atoms into a system of rigid bodies connected by joints. Contacts between rigid bodies enforce excluded volume constraints, and spring potentials model system elasticity. This simplified representation allows the conformations of complex molecular motors to be simulated interactively, providing a tool for hypothesis building and quantitative comparisons between models and experiments. In an example calculation, we have used the software to construct atomically detailed models of the myosin V molecular motor bound to its actin track. The software is available at www.simtk.org. PMID:20428469

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Qingdu; Guo, Jianli; Yang, Xiao-Song, E-mail: yangxs@hust.edu.cn

We present some rich new complex gaits in the simple walking model with upper body by Wisse et al. in [Robotica 22, 681 (2004)]. We first show that the stable gait found by Wisse et al. may become chaotic via period-doubling bifurcations. Such period-doubling routes to chaos exist for all parameters, such as foot mass, upper body mass, body length, hip spring stiffness, and slope angle. Then, we report three new gaits with period 3, 4, and 6; for each gait, there is also a period-doubling route to chaos. Finally, we show a practical method for finding a topological horseshoemore » in 3D Poincaré map, and present a rigorous verification of chaos from these gaits.« less

A new device for collecting time-integrated water samples from springs and surface water bodies

USGS Publications Warehouse

Panno, S.V.; Krapac, I.G.; Keefer, D.A.

1998-01-01

A new device termed the 'seepage sampler' was developed to collect representative water samples from springs, streams, and other surface-water bodies. The sampler collects composite, time-integrated water samples over short (hours) or extended (weeks) periods without causing significant changes to the chemical composition of the samples. The water sample within the sampler remains at the ambient temperature of the water body and does not need to be cooled. Seepage samplers are inexpensive to construct and easy to use. A sampling program of numerous springs and/or streams can be designed at a relatively low cost through the use of these samplers. Transient solutes migrating through such flow systems, potentially unnoticed by periodic sampling, may be detected. In addition, the mass loading of solutes (e.g., agrichemicals) may be determined when seepage samplers are used in conjunction with discharge measurements.

Granulometry and mineralogy of some northeastern Florida placers: a consequence of heavy mineral concentration in nearshore bars

NASA Astrophysics Data System (ADS)

Elsner, Harald

1992-03-01

Heavy mineral placer deposits of Pleistocene age in northeastern Florida were examined sedimentologically. Neither general setting, nor granulometric or mineralogic results are in agreement with a concentration of the heavy minerals in a beach, eolian or fluvial environment. Granulometric moment parameters of the ore sands seem to be distinctive. They include moderate sorting, high positive skewness, high kurtosis and a distinctive fine tail. Similarities of grain size curves of the placer sands with nearshore-offshore sands exist. Mineralogically the samples are more variable but always impoverished in epidote. This scarcity of epidote is atypical for eolian sediments in the study area, and the lack of garnet and the fineness of ore sands are uncommon for beach placers of northeast Florida. Underlain by dune ridges, which acted as obstacles on the shallow sea floor during the Penholoway transgression (1.3 ± 0.1 Ma B.P.), heavy minerals in the Boulogne and Green Cove Springs main ore body must have been concentrated in bars by the interplay of longshore and transverse bottom currents. Lighter heavy minerals were deposited in smaller nearshore bars closer to the former coast (Green Cove Springs small ore body) or in dunes of barrier islands (Green Cove Springs western ore body). As is true today, layers of noteworthy concentrations of economic minerals in the swash zone of Florida beaches were formed only rarely during storms, contrary to the coasts of Australia or India, where higher energetic conditions prevail. The proposed model of concentration of heavy minerals in certain outer nearshore bars has long been assumed but never been proven.

Development of gait training system powered by pneumatic actuator like human musculoskeletal system.

PubMed

Yamamoto, Shin-ichiroh; Shibata, Yoshiyuki; Imai, Shingo; Nobutomo, Tatsuya; Miyoshi, Tasuku

2011-01-01

The purpose of this study was to develop a body weight support gait training system for stroke and spinal cord injury (SCI) patient. This system consists of an orthosis powered by pneumatic McKibben actuators and a piece of equipment of body weight support. The attachment of powered orthosis can be fit to individual subjects with different body size. This powered orthosis is driven by pneumatic McKibben actuators arranged as a pair of agonistic and antagonistic bi-articular muscle models and two pairs of agonistic and antagonistic mono-articular muscle models like the human musculoskeletal system. The body weight support equipment suspends the subject's body in a wire harness, with the body weight is supported continuously by a counterweight. The powered orthosis is attached to the body weight support equipment by a parallel linkage, and its movement of powered orthosis is limited at the sagittal plane. The weight of the powered orthosis is compensated by a parallel linkage with a gas-spring. In this paper, we report the detailed mechanics of this body weight support gait training system and the results of several experiments for evaluating the system. © 2011 IEEE

Fluctuating water depths affect American alligator (Alligator mississippiensis) body condition in the Everglades, Florida, USA

USGS Publications Warehouse

Brandt, Laura A.; Beauchamp, Jeffrey S.; Jeffery, Brian M.; Cherkiss, Michael S.; Mazzotti, Frank J.

2016-01-01

Successful restoration of wetland ecosystems requires knowledge of wetland hydrologic patterns and an understanding of how those patterns affect wetland plant and animal populations.Within the Everglades, Florida, USA restoration, an applied science strategy including conceptual ecological models linking drivers to indicators is being used to organize current scientific understanding to support restoration efforts. A key driver of the ecosystem affecting the distribution and abundance of organisms is the timing, distribution, and volume of water flows that result in water depth patterns across the landscape. American alligators (Alligator mississippiensis) are one of the ecological indicators being used to assess Everglades restoration because they are a keystone species and integrate biological impacts of hydrological operations through all life stages. Alligator body condition (the relative fatness of an animal) is one of the metrics being used and targets have been set to allow us to track progress. We examined trends in alligator body condition using Fulton’s K over a 15 year period (2000–2014) at seven different wetland areas within the Everglades ecosystem, assessed patterns and trends relative to restoration targets, and related those trends to hydrologic variables. We developed a series of 17 a priori hypotheses that we tested with an information theoretic approach to identify which hydrologic factors affect alligator body condition. Alligator body condition was highest throughout the Everglades during the early 2000s and is approximately 5–10% lower now (2014). Values have varied by year, area, and hydrology. Body condition was positively correlated with range in water depth and fall water depth. Our top model was the “Current” model and included variables that describe current year hydrology (spring depth, fall depth, hydroperiod, range, interaction of range and fall depth, interaction of range and hydroperiod). Across all models, interaction between range and fall water depth was the most important variable (relative weight of 1.0) followed by spring and fall water depths (0.99), range (0.96), hydroperiod (0.95) and interaction between range and hydroperiod (0.95). Our work provides additional evidence that restoring a greater range in annual water depths is important for improvement of alligator body condition and ecosystem function. This information can be incorporated into both planning and operations to assist in reaching Everglades restoration goals.

A prospective longitudinal study of seasonality in African students living in the greater Washington, D.C. metropolitan area.

PubMed

Guzman, Alvaro; Zebrak, Ryszard; Rohan, Kelly J; Sumar, Irshad A; Savchenko, Svetlana; Stiller, John W; Valadez-Meltzer, Adela; Olsen, Cara; Lapidus, Manana; Soriano, Joseph J; Postolache, Teodor T

2007-05-01

We conducted a prospective, longitudinal study of seasonality in a vulnerable population, i.e., African students who migrated to a temperate climate. Consistent with previous cross-sectional studies, we hypothesized lower mood and energy, and higher appetite and weight, in fall/winter than in spring/summer. Four cohorts of African students attending a year-long nursing school program without vacation in Washington, D.C., were assessed monthly for 1 year. Forty-three subjects (mean age = 33.46 +/- 6.25), consisting of predominantly females (76.7%), completed the study. The cohorts began their academic program in different seasons (one each in winter, spring, summer, and fall), inherently minimizing confounding influences on seasonality, such as academic and immigration stress, as well as allowing adjustment for an order effect. At each assessment, students completed three 100-mm visual analog scales for mood, energy, and appetite, and were weighed on a digital scale. For each standardized dependent variable, a repeated measure ANOVA was used and, if a significant effect of month was identified, averages for spring/summer and fall/winter were compared using paired t-tests. In addition, a mixed model for repeated measures was applied to raw (nonstandardized) data. Body weight was significantly higher in fall/winter than in spring/summer (p < 0.01). No seasonal differences in mood, energy, or appetite were found. Benefiting from certain unique features of our cohorts allowing adjustment for order effects, this is the first study to identify a seasonal variation in body weight with a peak in winter using longitudinal monthly measurements.

Do Arctic breeding geese track or overtake a green wave during spring migration?

PubMed

Si, Yali; Xin, Qinchuan; de Boer, Willem F; Gong, Peng; Ydenberg, Ronald C; Prins, Herbert H T

2015-03-04

Geese breeding in the Arctic have to do so in a short time-window while having sufficient body reserves. Hence, arrival time and body condition upon arrival largely influence breeding success. The green wave hypothesis posits that geese track a successively delayed spring flush of plant development on the way to their breeding sites. The green wave has been interpreted as representing either the onset of spring or the peak in nutrient biomass. However, geese tend to adopt a partial capital breeding strategy and might overtake the green wave to accomplish a timely arrival on the breeding site. To test the green wave hypothesis, we link the satellite-derived onset of spring and peak in nutrient biomass with the stopover schedule of individual Barnacle Geese. We find that geese track neither the onset of spring nor the peak in nutrient biomass. Rather, they arrive at the southernmost stopover site around the peak in nutrient biomass, and gradually overtake the green wave to match their arrival at the breeding site with the local onset of spring, thereby ensuring gosling benefit from the peak in nutrient biomass. Our approach for estimating plant development stages is critical in testing the migration strategies of migratory herbivores.

Modal Damping Ratio and Optimal Elastic Moduli of Human Body Segments for Anthropometric Vibratory Model of Standing Subjects.

PubMed

Gupta, Manoj; Gupta, T C

2017-10-01

The present study aims to accurately estimate inertial, physical, and dynamic parameters of human body vibratory model consistent with physical structure of the human body that also replicates its dynamic response. A 13 degree-of-freedom (DOF) lumped parameter model for standing person subjected to support excitation is established. Model parameters are determined from anthropometric measurements, uniform mass density, elastic modulus of individual body segments, and modal damping ratios. Elastic moduli of ellipsoidal body segments are initially estimated by comparing stiffness of spring elements, calculated from a detailed scheme, and values available in literature for same. These values are further optimized by minimizing difference between theoretically calculated platform-to-head transmissibility ratio (TR) and experimental measurements. Modal damping ratios are estimated from experimental transmissibility response using two dominant peaks in the frequency range of 0-25 Hz. From comparison between dynamic response determined form modal analysis and experimental results, a set of elastic moduli for different segments of human body and a novel scheme to determine modal damping ratios from TR plots, are established. Acceptable match between transmissibility values calculated from the vibratory model and experimental measurements for 50th percentile U.S. male, except at very low frequencies, establishes the human body model developed. Also, reasonable agreement obtained between theoretical response curve and experimental response envelop for average Indian male, affirms the technique used for constructing vibratory model of a standing person. Present work attempts to develop effective technique for constructing subject specific damped vibratory model based on its physical measurements.

Depressurization valve

DOEpatents

Skoda, G.I.

1989-03-28

A depressurization valve for use in relieving completely the pressure in a simplified boiling water reactor is disclosed. The normally closed and sealed valve is provided with a valve body defining a conduit from an outlet of a manifold from the reactor through a valve seat. A closing valve disk is configured for fitting to the valve seat to normally close the valve. The seat below the disk is provided with a radially extending annulus extending a short distance into the aperture defined by the seat. The disk is correspondingly provided with a longitudinally extending annulus that extends downwardly through the aperture defined by the seat towards the high pressure side of the valve body. A ring shaped membrane is endlessly welded to the seat annulus and to the disk annulus. The membrane is conformed over the confronted surface of the seat and disk in a C-sectioned configuration to seal the depressurization valve against the possibility of weeping. The disk is held to the closed position by an elongate stem extending away from the high pressure side of the valve body. The stem has a flange configured integrally to the stem for bias by two springs. The first spring acts from a portion of the housing overlying the disk on the stem flange adjacent the disk. This spring urges the stem and attached disk away from the seat and thus will cause the valve to open at any pressure. A second spring-preferably of the Belleville variety-acts on a latch plate surrounding and freely moving relative to the end of the stem. This second spring overcomes the bias of the first spring and any pressure acting upon the disk. This Belleville spring maintains through its spring force the valve in the closed position. At the same time, the latch plate with its freedom of movement relative to the stem allows the stem to thermally expand during valve temperature excursion.

A finite element model of the lower limb during stance phase of gait cycle including the muscle forces.

PubMed

Diffo Kaze, Arnaud; Maas, Stefan; Arnoux, Pierre-Jean; Wolf, Claude; Pape, Dietrich

2017-12-07

Results of finite element (FE) analyses can give insight into musculoskeletal diseases if physiological boundary conditions, which include the muscle forces during specific activities of daily life, are considered in the FE modelling. So far, many simplifications of the boundary conditions are currently made. This study presents an approach for FE modelling of the lower limb for which muscle forces were included. The stance phase of normal gait was simulated. Muscle forces were calculated using a musculoskeletal rigid body (RB) model of the human body, and were subsequently applied to a FE model of the lower limb. It was shown that the inertial forces are negligible during the stance phase of normal gait. The contact surfaces between the parts within the knee were modelled as bonded. Weak springs were attached to the distal tibia for numerical reasons. Hip joint reaction forces from the RB model and those from the FE model were similar in magnitude with relative differences less than 16%. The forces of the weak spring were negligible compared to the applied muscle forces. The maximal strain was 0.23% in the proximal region of the femoral diaphysis and 1.7% in the contact zone between the tibia and the fibula. The presented approach based on FE modelling by including muscle forces from inverse dynamic analysis of musculoskeletal RB model can be used to perform analyses of the lower limb with very realistic boundary conditions. In the present form, this model can be used to better understand the loading, stresses and strains of bones in the knee area and hence to analyse osteotomy fixation devices.

A Spring Forward for Human Evolution in East Africa?

NASA Astrophysics Data System (ADS)

Cuthbert, M. O.; Ashley, G. M.

2014-12-01

The current consensus is that humans evolved in Africa and then migrated in waves to other parts of the world starting as early as 2 Ma. The climate was both cooling and drying. One of the major unknowns connected with human survival in this climatically turbulent environment is the availability of resources, particularly water. A growing body of geological evidence shows an association between springs, stone tools and hominin fossils at a number of sites in the East African Rift System (EARS) during a critical period for hominin evolution (from 1.8 Ma). The springs may have been vulnerable to climate variability, thus the role that groundwater availability may have played in human evolution and migration to other continents is not known. Using palaeogeological reconstruction and groundwater modelling of the paleo-catchment of one such EARS site, Olduvai Gorge (3°S), we show how spring discharge was likely linked to climate variability of annual to Milankovitch cycle timescales. Under decadal to centennial timescales, spring flow would have been relatively invariant providing good water resource resilience through long droughts. For multi-millennial periods, modelled spring flows lag groundwater recharge by 100s to 1000 years. Our results show how groundwater would have provided 'drought proof' water supply and habitats during arid phases as potable surface water from rivers or lakes became increasingly scarce. Localized groundwater systems are likely to have been widespread within the EARS providing refugia and intense competition during dry periods. Thus, springs and associated wetlands may have been important factors in natural selection and evolution, as well as a vital resource during dispersal within and out of Africa. While further exploration is needed to test the geographical extent of groundwater use by early humans, we propose that groundwater flow systems produced in the EARS played a significant role in the evolution and dispersal of early humans.

Spring snow goose hunting influences body composition of waterfowl staging in Nebraska

USGS Publications Warehouse

Pearse, Aaron T.; Krapu, Gary L.; Cox, Robert R.

2012-01-01

A spring hunt was instituted in North America to reduce abundance of snow geese (Chen caerulescens) by increasing mortality of adults directly, yet disturbance from hunting activities can indirectly influence body condition and ultimately, reproductive success. We estimated effects of hunting disturbance by comparing body composition of snow geese and non-target species, greater white-fronted geese (Anser albifrons) and northern pintails (Anas acuta) collected in portions of south-central Nebraska that were open (eastern Rainwater Basin, ERB) and closed (western Rainwater Basin, WRB; and central Platte River Valley, CPRV) to snow goose hunting during springs 1998 and 1999. Lipid content of 170 snow geese was 25% (57 g) less in areas open to hunting compared to areas closed during hunting season but similar in all areas after hunting was concluded in the ERB. Protein content of snow geese was 3% (14 g) less in the region open to hunting. Greater white-fronted geese had 24% (76 g; n = 129) less lipids in the hunted portion of the study area during hunting season, and this difference persisted after conclusion of hunting season. We found little difference in lipid or protein content of northern pintails in relation to spring hunting. Indirect effects of spring hunting may be considered a collateral benefit regarding efforts to reduce overabundant snow goose populations. Disrupted nutrient storage observed in greater white-fronted geese represents an unintended consequence of spring hunting that has potential to adversely affect reproduction for this and other species of waterbirds staging in the region.

A Generalized Maxwell Model for Creep Behavior of Artery Opening Angle

PubMed Central

Zhang, W.; Guo, X.; Kassab, G. S.

2009-01-01

An artery ring springs open into a sector after a radial cut. The opening angle characterizes the residual strain in the unloaded state, which is fundamental to understanding stress and strain in the vessel wall. A recent study revealed that the opening angle decreases with time if the artery is cut from the loaded state, while it increases if the cut is made from the no-load state due to viscoelasticity. In both cases, the opening angle approaches the same value in 3 hours. This implies that the characteristic relaxation time is about 10,000 sec. Here, the creep function of a generalized Maxwell model (a spring in series with six Voigt bodies) is used to predict the temporal change of opening angle in multiple time scales. It is demonstrated that the theoretical model captures the salient features of the experimental results. The proposed creep function may be extended to study the viscoelastic response of blood vessels under various loading conditions. PMID:19045526

Further Investigations of High Temperature Knitted Spring Tubes for Advanced Control Surface Seal Applications

NASA Technical Reports Server (NTRS)

Taylor, Shawn C.; DeMange, Jeffrey J.; Dunlap, Patrick H., Jr.; Steinetz, Bruce M.

2006-01-01

Knitted metallic spring tubes are the structural backbones that provide resiliency in control surface seals for use on current and future reusable space launch vehicles. Control surface seals fill the space between movable control surfaces such as body flaps, rudders and elevons, and the static body structures to which they are attached. These seals must remain in continuous contact with opposing surfaces to prevent the ingestion of damaging hot gases encountered during atmospheric re-entry. The Inconel X-750 (Special Metals Corporation) spring tube utilized in the baseline control surface seal shows significant resiliency loss when compressed at temperatures as low as 1200 F. High temperature compression testing and microstructural analysis show that creep is the dominant deformation mechanism leading to permanent set and resiliency loss in tested spring tube samples. Additional evaluation using a structured design of experiments approach shows that spring tube performance, primarily high temperature resiliency, can be enhanced through material substitution of Rene 41 (Allvac) alloy (for the baseline Inconel X-750 material) when coupled with specialized thermal processing.

Comparison of Estimated Areas Contributing Recharge to Selected Springs in North-Central Florida by Using Multiple Ground-Water Flow Models

USGS Publications Warehouse

Shoemaker, W. Barclay; O'Reilly, Andrew M.; Sepúlveda, Nicasio; Williams, Stanley A.; Motz, Louis H.; Sun, Qing

2004-01-01

Areas contributing recharge to springs are defined in this report as the land-surface area wherein water entering the ground-water system at the water table eventually discharges to a spring. These areas were delineated for Blue Spring, Silver Springs, Alexander Springs, and Silver Glen Springs in north-central Florida using four regional ground-water flow models and particle tracking. As expected, different models predicted different areas contributing recharge. In general, the differences were due to different hydrologic stresses, subsurface permeability properties, and boundary conditions that were used to calibrate each model, all of which are considered to be equally feasible because each model matched its respective calibration data reasonably well. To evaluate the agreement of the models and to summarize results, areas contributing recharge to springs from each model were combined into composite areas. During 1993-98, the composite areas contributing recharge to Blue Spring, Silver Springs, Alexander Springs, and Silver Glen Springs were about 130, 730, 110, and 120 square miles, respectively. The composite areas for all springs remained about the same when using projected 2020 ground-water withdrawals.

Combined statistical and mechanistic modelling suggests food and temperature effects on survival of early life stages of Northeast Arctic cod (Gadus morhua)

NASA Astrophysics Data System (ADS)

Stige, Leif Chr.; Langangen, Øystein; Yaragina, Natalia A.; Vikebø, Frode B.; Bogstad, Bjarte; Ottersen, Geir; Stenseth, Nils Chr.; Hjermann, Dag Ø.

2015-05-01

Understanding the causes of the large interannual fluctuations in the recruitment to many marine fishes is a key challenge in fisheries ecology. We here propose that the combination of mechanistic and statistical modelling of the pelagic early life stages (ELS) prior to recruitment can be a powerful approach for improving our understanding of local-scale and population-scale dynamics. Specifically, this approach allows separating effects of ocean transport and survival, and thereby enhances the knowledge of the processes that regulate recruitment. We analyse data on the pelagic eggs, larvae and post-larvae of Northeast Arctic cod and on copepod nauplii, the main prey of the cod larvae. The data originate from two surveys, one in spring and one in summer, for 30 years. A coupled physical-biological model is used to simulate the transport, ambient temperature and development of cod ELS from spawning through spring and summer. The predictions from this model are used as input in a statistical analysis of the summer data, to investigate effects of covariates thought to be linked to growth and survival. We find significant associations between the local-scale ambient copepod nauplii concentration and temperature in spring and the local-scale occurrence of cod (post)larvae in summer, consistent with effects on survival. Moreover, years with low copepod nauplii concentrations and low temperature in spring are significantly associated with lower mean length of the cod (post)larvae in summer, likely caused in part by higher mortality leading to increased dominance of young and hence small individuals. Finally, we find that the recruitment at age 3 is strongly associated with the mean body length of the cod ELS, highlighting the biological significance of the findings.

A simple running model with rolling contact and its role as a template for dynamic locomotion on a hexapod robot.

PubMed

Huang, Ke-Jung; Huang, Chun-Kai; Lin, Pei-Chun

2014-10-07

We report on the development of a robot's dynamic locomotion based on a template which fits the robot's natural dynamics. The developed template is a low degree-of-freedom planar model for running with rolling contact, which we call rolling spring loaded inverted pendulum (R-SLIP). Originating from a reduced-order model of the RHex-style robot with compliant circular legs, the R-SLIP model also acts as the template for general dynamic running. The model has a torsional spring and a large circular arc as the distributed foot, so during locomotion it rolls on the ground with varied equivalent linear stiffness. This differs from the well-known spring loaded inverted pendulum (SLIP) model with fixed stiffness and ground contact points. Through dimensionless steps-to-fall and return map analysis, within a wide range of parameter spaces, the R-SLIP model is revealed to have self-stable gaits and a larger stability region than that of the SLIP model. The R-SLIP model is then embedded as the reduced-order 'template' in a more complex 'anchor', the RHex-style robot, via various mapping definitions between the template and the anchor. Experimental validation confirms that by merely deploying the stable running gaits of the R-SLIP model on the empirical robot with simple open-loop control strategy, the robot can easily initiate its dynamic running behaviors with a flight phase and can move with similar body state profiles to those of the model, in all five testing speeds. The robot, embedded with the SLIP model but performing walking locomotion, further confirms the importance of finding an adequate template of the robot for dynamic locomotion.

Beneficial effect of hot spring bathing on stress levels in Japanese macaques.

PubMed

Takeshita, Rafaela S C; Bercovitch, Fred B; Kinoshita, Kodzue; Huffman, Michael A

2018-05-01

The ability of animals to survive dramatic climates depends on their physiology, morphology and behaviour, but is often influenced by the configuration of their habitat. Along with autonomic responses, thermoregulatory behaviours, including postural adjustments, social aggregation, and use of trees for shelter, help individuals maintain homeostasis across climate variations. Japanese macaques (Macaca fuscata) are the world's most northerly species of nonhuman primates and have adapted to extremely cold environments. Given that thermoregulatory stress can increase glucocorticoid concentrations in primates, we hypothesized that by using an available hot spring, Japanese macaques could gain protection against weather-induced cold stress during winter. We studied 12 adult female Japanese macaques living in Jigokudani Monkey Park, Japan, during the spring birth season (April to June) and winter mating season (October to December). We collected faecal samples for determination of faecal glucocorticoid (fGC) metabolite concentrations by enzyme immunoassay, as well as behavioural data to determine time spent in the hot springs, dominance rank, aggression rates, and affiliative behaviours. We used nonparametric statistics to examine seasonal changes in hot spring bathing, and the relationship between rank and air temperature on hot spring bathing. We used general linear mixed-effect models to examine factors impacting hormone concentrations. We found that Japanese macaques use hot spring bathing for thermoregulation during the winter. In the studied troop, the single hot spring is a restricted resource favoured by dominant females. High social rank had both costs and benefits: dominant females sustained high fGC levels, which were associated with high aggression rates in winter, but benefited by priority of access to the hot spring, which was associated with low fGC concentrations and therefore might help reduce energy expenditure and subsequent body heat loss. This unique habit of hot spring bathing by Japanese macaques illustrates how behavioural flexibility can help counter cold climate stress, with likely implications for reproduction and survival.

Lupus: When the Body Attacks Itself | NIH MedlinePlus the Magazine

MedlinePlus

... of this page please turn JavaScript on. Feature: Lupus Lupus: When the Body Attacks Itself Past Issues / Spring 2014 Table of Contents fast facts 1 Lupus occurs when the body's immune system attacks the ...

A Novel Model to Simulate Flexural Complements in Compliant Sensor Systems

PubMed Central

Tang, Hongyan; Zhang, Dan; Guo, Sheng; Qu, Haibo

2018-01-01

The main challenge in analyzing compliant sensor systems is how to calculate the large deformation of flexural complements. Our study proposes a new model that is called the spline pseudo-rigid-body model (spline PRBM). It combines dynamic spline and the pseudo-rigid-body model (PRBM) to simulate the flexural complements. The axial deformations of flexural complements are modeled by using dynamic spline. This makes it possible to consider the nonlinear compliance of the system using four control points. Three rigid rods connected by two revolute (R) pins with two torsion springs replace the three lines connecting the four control points. The kinematic behavior of the system is described using Lagrange equations. Both the optimization and the numerical fitting methods are used for resolving the characteristic parameters of the new model. An example is given of a compliant mechanism to modify the accuracy of the model. The spline PRBM is important in expanding the applications of the PRBM to the design and simulation of flexural force sensors. PMID:29596377

a Decade of Improvement in Whole-Body Vibration and Low Back Pain for Freight Container Tractor Drivers

NASA Astrophysics Data System (ADS)

Nishiyama, K.; Taoda, K.; Kitahara, T.

1998-08-01

The authors' study in 1983 revealed that the whole-body vibration of the tractor units of freight containers was most hazardous in the back-to-chest directions (x-axis). The allowable exposure time was considerably shorter than that for heavy duty trucks. The low back pain (LBP) among the drivers seemed to be due to the long working hours and the ergonomically unsound tractor design, as well as the vibration. A preventative measure was the introduction of a tractor cab suspended by an air spring instead of a steel spring. In 1992, a follow-up field study was conducted. A personal vibration exposure meter developed by us measured the whole-body vibration on eight tractors. Eighty-nine triplets matched with the age and the years of driving tractors answered a questionnaire evaluation of the ergonomics of their tractor units.The comparison of the newest steel suspension vehicles to the old ones produced by the same motor company revealed that in thex-axis the vibration level had decreased by as much as 4 to 9 dB. Some tractors showed an increase in vibration in the buttocks-to-head direction (z-axis). However, such adverse changes seemed not to affect evaluations according to the fatigue-decreased proficiency boundary (FDP) and the exposure limit (EL) recommended in ISO 2631-1978. The present models, regardless of the type of suspension, changed the direction of the most hazardous vibration from thex-axis to thez-axis. However, the effect of the air-suspension was not so remarkable as expected. Among 40% of drivers seemed to exceed the FDP boundary during a day.The questionnaire study showed an improvement in the ergonomic evaluation of the tractors. The air suspension models seemed to induce less LBP than the steel suspension models.

Preloaded latching device

NASA Technical Reports Server (NTRS)

Wesselski, Clarence J. (Inventor); Nagy, Kornel (Inventor)

1992-01-01

A latching device is disclosed which is lever operated sequentially to actuate a set of collet fingers to provide a radial expansion and to actuate a force mechanism to provide a compressive gripping force for attaching first and second devices to one another. The latching device includes a body member having elongated collet fingers which, in a deactuated condition, is insertable through bores on the first and second devices so that gripping terminal portions on the collet fingers are proximate to the end of the bore of the first device while a spring assembly on the body member is located proximate to the outer surface of a second device. A lever is rotatable through 90 deg to move a latching rod to sequentially actuate and expand collet fingers and to actuate the spring assembly by compressing it. During the first 30 deg of movement of the lever, the collet fingers are actuated by the latching rod to provide a radial expansion and during the last 60 deg of movement of the lever, the spring assembly acts as a force mechanism and is actuated to develop a compressive latching force on the devices. The latching rod and lever are connected by a camming mechanism. The amount of spring force in the spring assembly can be adjusted; the body member can be permanently attached by a telescoping assembly to one of the devices; and the structure can be used as a pulling device for removing annular bearings or the like from blind bores.

Conceptual Model and Numerical Simulation of the Ground-Water-Flow System in the Unconsolidated Sediments of Thurston County, Washington

USGS Publications Warehouse

Drost, B.W.; Ely, D.M.; Lum, W. E.

1999-01-01

The demand for water in Thurston County has increased steadily in recent years because of a rapid growth in population. Surface-water resources in the county have been fully appropriated for many years and Thurston County now relies entirely on ground water for new supplies of water. Thurston County is underlain by up to 2,000 feet of unconsolidated glacial and non-glacial Quaternary sediments which overlie consolidated rocks of Tertiary age. Six geohydrologic units have been identified within the unconsolidated sediments. Between 1988 and 1990, median water levels rose 0.6 to 1.9 feet in all geohydrologic units except bedrock, in which they declined 1.4 feet. Greater wet-season precipitation in 1990 (43 inches) than in 1988 (26 inches) was the probable cause of the higher 1990 water levels. Ground-water flow in the unconsolidated sediments underlying Thurston County was simulated with a computerized numerical model (MODFLOW). The model was constructed to simulate 1988 ground-water conditions as steady state. Simulated inflow to the model area from precipitation and secondary recharge was 620,000 acre-feet per year (93 percent), leakage from streams and lakes was 38,000 acre-ft/yr (6 percent), and ground water entering the model along the Chehalis River valley was 5,800 acre-ft/yr (1 percent). Simulated outflow from the model was primarily leakage to streams, springs, lakes, and seepage faces (500,000 acre-ft/yr or 75 percent of the total outflow). Submarine seepage to Puget Sound was simulated to be 88,000 acre-ft/yr (13 percent). Simulated ground-water discharge along the Chehalis River valley was simulated to be 12,000 acreft/yr (2 percent). Simulated withdrawals by wells for all purposes was 62,000 acre-ft/yr (9 percent). The numerical model was used to simulate the possible effects of increasing ground-water withdrawals by 23,000 acre-ft/yr above the 1988 rate of withdrawal. The model indicated that the increased withdrawals would come from reduced discharge to springs, seepage faces, and offshore (total of 51 percent of increased pumping) and decreased flow to rivers (46 percent). About 3 percent would come from increased leakage from rivers. Water levels would decline more than 1 foot over most of the model area, more than 10 feet over some areas, and would be at a maximum of about 35 feet. Contributing areas for water discharging at McAllister and Abbott Springs and to pumping centers near Tumwater and Lacey were estimated using a particle-tracking post-processing computer code (MODPATH) and a MODFLOW model calibrated to steady-state (1988) conditions. Water discharging at McAllister and Abbot Springs was determined to come from water entering the ground-water system at the water table in an area of about 20 square miles (mi2) to the west and south of the springs. This water is estimated to come from recharge (both precipitation and secondary) and from leakage from Lake St. Clair and several other surface-water bodies. Southeast of Lacey, about 3,800 acre-ft of ground water were pumped from five municipal wells during 1988. The source of the pumped water was determined to be an area that covers about 1.1 mi2. The water was estimated to come from recharge (both precipitation and secondary) and leakage from surface-water bodies. Along the lower Deschutes River nearly 3,900 acre-ft/yr of ground water were pumped during 1988 from 15 wells for municipal and industrial use. The calculated source of this water was an area that covers about 1.3 mi2. Within the calculated contributing area the pumped ground water comes from recharge (both precipitation and secondary) and leakage from the Deschutes River and several other surface-water bodies.

Factors associated with early cyclicity in postpartum dairy cows.

PubMed

Vercouteren, M M A A; Bittar, J H J; Pinedo, P J; Risco, C A; Santos, J E P; Vieira-Neto, A; Galvão, K N

2015-01-01

The objective of this study was to evaluate factors associated with resumption of ovarian cyclicity within 21 days in milk (DIM) in dairy cows. Cows (n=768) from 2 herds in north Florida had their ovaries scanned at 17±3, 21±3, and 24±3 DIM. Cows that had a corpus luteum ≥20mm at 17±3 or at 21±3 DIM or that had a corpus luteum <20mm in 2 consecutive examinations were determined to be cyclic by 21±3 DIM. The following information was collected for up to 14 DIM: calving season, parity, calving problems, metabolic problems, metritis, mastitis, digestive problems, lameness, body weight loss, dry period length, and average daily milk yield. Body condition was scored at 17±3 DIM. Multivariable mixed logistic regression analysis was performed using the GLIMMIX procedure of SAS. Variables with P≤0.2 were considered in each model. Herd was included as a random variable. Three models were constructed: model 1 included all cows, model 2 included only cows from dairy 1 that had daily body weights available, and model 3 included only multiparous cows with a previous dry period length recorded. In model 1, variables associated with greater cyclicity by 21±3 DIM were calving in the summer and fall rather than in the winter or spring, being multiparous rather than primiparous, and not having metabolic or digestive problems. In model 2, variables associated with greater cyclicity by 21±3 DIM were calving in the summer and fall, not having metritis or digestive problems and not losing >28 kg of BW within 14 DIM. In model 3, variables associated with greater cyclicity by 21±3 DIM were absence of metabolic problems and dry period ≤76 d. In summary, cyclicity by 21±3 DIM was negatively associated with calving in winter or spring, primiparity, metritis, metabolic or digestive problems, loss of >28 kg of body weight, and a dry period >76d. Strategies preventing extended dry period length and loss of BW, together with reductions in the incidence of metritis as well as metabolic and digestive problems should improve early cyclicity postpartum. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Towards a footwear design tool: influence of shoe midsole properties and ground stiffness on the impact force during running.

PubMed

Ly, Quoc Hung; Alaoui, Amina; Erlicher, Silvano; Baly, Laurent

2010-01-19

Several spring-damper-mass models of the human body have been developed in order to reproduce the measured ground vertical reaction forces during human running (McMahon and Cheng, 1990; Ferris et al., 1999; Liu and Nigg, 2000). In particular, Liu and Nigg introduced at the lower level of their model, i.e. at the interface between the human body and the ground, a nonlinear element representing simultaneously the shoe midsoles and the ground flexibility. The ground reaction force is modelled as the force supported by this nonlinear element, whose parameters are identified from several sets of experimental data. This approach proved to be robust and quite accurate. However, it does not explicitly take into account the shoe and the ground properties. It turns out to be impossible to study the influence of shoe materials on the impact force, for instance for footwear design purposes. In this paper, a modification of the Liu and Nigg's model is suggested, where the original nonlinear element is replaced with a bi-layered spring-damper-mass model: the first layer represents the shoe midsole and the second layer is associated with the ground. Ground is modelled as an infinite elastic half-space. We have assumed a viscoelastic behaviour of the shoe material, so the damping of shoe material is taken into account. A methodology for the shoe-soles characterization is proposed and used together with the proposed model. A parametric study is then conducted and the influence of the shoe properties on the impact force is quantified. Moreover, it is shown that impact forces are strongly affected by the ground stiffness, which should therefore be considered as an essential parameter in the footwear design. Copyright 2009 Elsevier Ltd. All rights reserved.

Subaqueous hot springs in Köyceğiz Lake, Dalyan Channel and Fethiye-Göcek Bay (SW Turkey): Locations, chemistry and origins

NASA Astrophysics Data System (ADS)

Avşar, Özgür; Avşar, Ulaş; Arslan, Şebnem; Kurtuluş, Bedri; Niedermann, Samuel; Güleç, Nilgün

2017-10-01

In this study, horizontal temperature measurements along organized grids have been used to detect subaqueous hot springs. The study area, located in the southwest of Turkey and comprised of Köyceğiz Lake, Dalyan Channel and Fethiye-Göcek Bay, was scanned by measuring temperatures horizontally, 2-3 m above the bottom of the lake or sea. After analyzing the temperature data along the grids, the locations with anomalous temperature values were detected, and divers headed here for further verification. Accordingly, among these anomalies, the divers confirmed seven of them as subaqueous hot springs. Three of these hot springs are located in the Köyceğiz Lake, three of them are located in the Dalyan Channel and one hot spring is located in the Fethiye-Göcek Bay. At the locations where temperature anomalies were detected, the divers collected samples directly from the subaqueous hot spring using a syringe-type sampler. We evaluated these water samples together with samples collected from hot and cold springs on land and from local rivers, lakes and the sea, with an aim to generate a conceptual hydrogeochemical model of the geothermal system in the study area. This model predicts that rainwater precipitating in the highlands percolates through fractures and faults into the deeper parts of the Earth's crust, here it is heated and ascends through the sea bottom via buried faults. Pervious carbonate nappes that are underlain and overlain by impervious rocks create a confined aquifer. The southern boundary of the Carbonate-Marmaris nappes is buried under alluvium and/or sea/lake water bodies and this phenomenon determines whether hot springs occur on land or subaqueous. The chemical and isotopic properties of the hot springs point to seawater mixing at deep levels. Thus, the mixing most probably occurs while the water is ascending through the faults and fractures. The gas geochemistry results reveal that the lowest mantle He contributions occur in the samples from Köycegiz Lake, whereas the highest ones are found in samples from the Dalaman plain. For the first time, we made use of the micro-XRF sediment core scanning (ITRAX Scanner) for exploring the relation between subaqueous geothermal occurrence and chemical properties of the surrounding sediments. The spatial elemental distribution of sea/lake bottom sediments suggests that depending on the surrounding rock units and the temperature of the hot spring, the sediments around the spring can be enriched with certain elements.

Influence of "J"-Curve Spring Stiffness on Running Speeds of Segmented Legs during High-Speed Locomotion.

PubMed

Wang, Runxiao; Zhao, Wentao; Li, Shujun; Zhang, Shunqi

2016-01-01

Both the linear leg spring model and the two-segment leg model with constant spring stiffness have been broadly used as template models to investigate bouncing gaits for legged robots with compliant legs. In addition to these two models, the other stiffness leg spring models developed using inspiration from biological characteristic have the potential to improve high-speed running capacity of spring-legged robots. In this paper, we investigate the effects of "J"-curve spring stiffness inspired by biological materials on running speeds of segmented legs during high-speed locomotion. Mathematical formulation of the relationship between the virtual leg force and the virtual leg compression is established. When the SLIP model and the two-segment leg model with constant spring stiffness and with "J"-curve spring stiffness have the same dimensionless reference stiffness, the two-segment leg model with "J"-curve spring stiffness reveals that (1) both the largest tolerated range of running speeds and the tolerated maximum running speed are found and (2) at fast running speed from 25 to 40/92 m s -1 both the tolerated range of landing angle and the stability region are the largest. It is suggested that the two-segment leg model with "J"-curve spring stiffness is more advantageous for high-speed running compared with the SLIP model and with constant spring stiffness.

Influence of “J”-Curve Spring Stiffness on Running Speeds of Segmented Legs during High-Speed Locomotion

PubMed Central

2016-01-01

Both the linear leg spring model and the two-segment leg model with constant spring stiffness have been broadly used as template models to investigate bouncing gaits for legged robots with compliant legs. In addition to these two models, the other stiffness leg spring models developed using inspiration from biological characteristic have the potential to improve high-speed running capacity of spring-legged robots. In this paper, we investigate the effects of “J”-curve spring stiffness inspired by biological materials on running speeds of segmented legs during high-speed locomotion. Mathematical formulation of the relationship between the virtual leg force and the virtual leg compression is established. When the SLIP model and the two-segment leg model with constant spring stiffness and with “J”-curve spring stiffness have the same dimensionless reference stiffness, the two-segment leg model with “J”-curve spring stiffness reveals that (1) both the largest tolerated range of running speeds and the tolerated maximum running speed are found and (2) at fast running speed from 25 to 40/92 m s−1 both the tolerated range of landing angle and the stability region are the largest. It is suggested that the two-segment leg model with “J”-curve spring stiffness is more advantageous for high-speed running compared with the SLIP model and with constant spring stiffness. PMID:28018127

Users manual: Dynamics of two bodies connected by an elastic tether, six degrees of freedom forebody and five degrees of freedom decelerator

NASA Technical Reports Server (NTRS)

Doyle, G. R., Jr.; Burbick, J. W.

1974-01-01

The equations of motion and a computer program for the dynamics of a six degree of freedom body joined to a five degree of freedom body by a quasilinear elastic tether are presented. The forebody is assumed to be a completely general rigid body with six degrees of freedom; the decelerator is also assumed to be rigid, but with only five degrees of freedom (symmetric about its longitudinal axis). The tether is represented by a spring and dashpot in parallel, where the spring constant is a function of tether elongation. Lagrange's equation is used to derive the equations of motion with the Lagrange multiplier technique used to express the constraint provided by the tether. A computer program is included which provides a time history of the dynamics of both bodies and the tension in the tether.

Three-Dimensional Analysis of dike/fault interaction at Mono Basin (California) using the Finite Element Method

NASA Astrophysics Data System (ADS)

La Marra, D.; Battaglia, M.

2013-12-01

Mono Basin is a north-trending graben that extends from the northern edge of Long Valley caldera towards the Bodie Hills and is bounded by the Cowtrack Mountains on the east and the Sierra Nevada on the west. The Mono-Inyo Craters volcanic chain forms a north-trending zone of volcanic vents extending from the west moat of the Long Valley caldera to Mono Lake. The Hartley Springs fault transects the southern Mono Craters-Inyo Domes area between the western part of the Long Valley caldera and June Lake. Stratigraphic data suggest that a series of strong earthquakes occurred during the North Mono-Inyo eruption sequence of ~1350 A.D. The spatial and temporal proximity between Hartley Springs Fault motion and the North Mono-Inyo eruption sequence suggests a possible relation between seismic events and eruptions. We investigate the interactions between slip along the Hartley Springs fault and dike intrusion beneath the Mono-Inyo craters using a three-dimensional finite element model of the Mono Basin. We employ a realistic representation of the Basin that includes topography, vertical and lateral heterogeneities of the crust, contact relations between fault planes, and a physical model of the pressure required to propagate the dike. We estimate (a) the distribution of Coulomb stress changes to study the influence of dike intrusion on Hartley Springs fault, and (b) the local stress and volumetric dilatation changes to understand how fault slip may influence the propagation of a dike towards the surface.

Depressurization valve

DOEpatents

Skoda, George I.

1989-01-01

A depressurization valve for use in relieving completely the pressure in a simplified boiling water reactor is disclosed. The normally closed and sealed valve is provided with a valve body defining a conduit from an outlet of a manifold from the reactor through a valve seat. A closing valve disk is configured for fitting to the valve seat to normally close the valve. The seat below the disk is provided with a radially extending annulus extending a short distance into the aperture defined by the seat. The disk is correspondingly provided with a longitudinally extending annulus that extends downwardly through the aperture defined by the seat towards the high pressure side of the valve body. A ring shaped membrane is endlessly welded to the seat annulus and to the disk annulus. The membrane is conformed over the confronted surface of the seat and disk in a C-sectioned configuration to seal the depressurization valve against the possibility of weeping. The disk is held to the closed position by an elongate stem extending away from the high pressure side of the valve body. The stem has a flange configured integrally to the stem for bias by two springs. The first spring acts from a portion of the housing overlying the disk on the stem flange adjacent the disk. This spring urges the stem and attached disk away from the seat and thus will cause the valve to open at any pressure. A second spring--preferably of the Belleville variety--acts on a latch plate surrounding and freely moving relative to the end of the stem. This second spring overcomes the bias of the first spring and any pressure acting upon the disk. This Belleville spring maintains through its spring force the valve in the closed position. At the same time, the latch plate with its freedom of movement relative to the stem allows the stem to thermally expand during valve temperature excursion. The latch plate in surrounding the stem is limited in its outward movement by a boss attached to the stem at the end of the stem remote from the disk. The latch plate is held normally closed by three radial latches spaced at 120.degree. around the periphery of the plate.

Diel feeding behavior and ingestion rate in the copepod Calanus finmarchicus in the southern Gulf of Maine during late spring

NASA Astrophysics Data System (ADS)

Durbin, Edward G.; Campbell, Robert G.; Gilman, Sharon L.; Durbin, Ann G.

In situ feeding was measured on late stage Calanus finmarchicus in the southern Gulf of Maine during late spring 1988 and 1989. The region is a spring feeding ground for the planktivorous right whale, Eubalaena glacialis. Measurements in 1988 were made during the declining spring bloom, when phytoplankton showed considerable spatial variability. 1989 observations were made after summer stratification had become established, when phytoplankton biomass was low and dominated by the <7 μm size fraction. In situ ingestion rates of C. finmarchicus reflected these differences in food, and ranged from 30.2% body C day -1 at a spring bloom station to 0.6% body C day -1 after stratification. These values compare with a maximum ingestion rate of 44.3% body C day -1 measured in a shipboard grazing experiment using cultured algae as food, and indicate that C. finmarchicus became food limited in the southern Gulf of Maine after stratification. Calanus finmarchicus diet feeding behavior and diet vertical migration patterns changed during the seasonal progression from spring bloom to summer stratification. Diet feeding rhythms and vertical migration were absent during the bloom, but developed as the bloom declined. During the post-bloom stratified conditions, diet feeding rhythms continued but vertical migration ceased. Most of the C. finmarchicus population remained near the surface, while a small population of nonmigratory individuals resided at depth and appeared to be feeding upon sedimented spring bloom diatoms. At the spring bloom station C. finmarchicus ingested only a small proportion of the phytoplankton standing stock in the > 7 μm size fraction (2.9% day -1), reflecting the high biomass of phytoplankton and the stage composition of the C. finmarchicus population, dominated by early copepodite stages with low biomass. In contrast, at the post-bloom stations in 1989, the dense surface aggregations of C. finmarchicus populations were dominated by late copepodite stages whose total biomass was comparable to that of the phytoplankton, and C. finmarchicus consumed a significantly larger fraction of the > 7 μm phytoplankton standing crop (up to 62.5% day -1.

A model for flexi-bar to evaluate intervertebral disc and muscle forces in exercises.

PubMed

Abdollahi, Masoud; Nikkhoo, Mohammad; Ashouri, Sajad; Asghari, Mohsen; Parnianpour, Mohamad; Khalaf, Kinda

2016-10-01

This study developed and validated a lumped parameter model for the FLEXI-BAR, a popular training instrument that provides vibration stimulation. The model which can be used in conjunction with musculoskeletal-modeling software for quantitative biomechanical analyses, consists of 3 rigid segments, 2 torsional springs, and 2 torsional dashpots. Two different sets of experiments were conducted to determine the model's key parameters including the stiffness of the springs and the damping ratio of the dashpots. In the first set of experiments, the free vibration of the FLEXI-BAR with an initial displacement at its end was considered, while in the second set, forced oscillations of the bar were studied. The properties of the mechanical elements in the lumped parameter model were derived utilizing a non-linear optimization algorithm which minimized the difference between the model's prediction and the experimental data. The results showed that the model is valid (8% error) and can be used for simulating exercises with the FLEXI-BAR for excitations in the range of the natural frequency. The model was then validated in combination with AnyBody musculoskeletal modeling software, where various lumbar disc, spinal muscles and hand muscles forces were determined during different FLEXI-BAR exercise simulations. Copyright © 2016 IPEM. Published by Elsevier Ltd. All rights reserved.

Geophysical model of Mt. Labo geothermal field, Southeastern Luzon, Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Los Banos, C.F. Jr.; Layugan, D.B.; Maneja, F.C.

1996-12-31

The geophysical model of Mt. Labo geothermal field, based on the results of the regional gravity and magnetotelluric (MT) surveys, indicates a geothermal reservoir centered beneath the Mabahong Labo thermal ground. The heat source of the present hydrothermal system is provided by a cooling intrusive body, mapped as a gravity high, associated with the Mt. Labo volcanic activity. The geothermal fluids circulate along fractures within the low-density reservoir rocks of the Susung Dalaga Formation. This reservoir rock shows relatively high resistivity values of 30 to 40 ohm-m. Directly overlying the resistive reservoir, occurring between -1000 m to -1500 m, ismore » a thick alteration halo formed within the basal unit of the Labo Volcanics (Lbu). The predominantly hydrous, low-temperature clay minerals which compose the alteration halo give low resistivity values of 1 to 4 ohm-m. Outflow of hot fluids to the south-southwest, which possibly feeds the thermal springs at Kilbay and Alawihaw, may be channeled along the thinning low resistivity Lbu. The geophysical model also shows a possible separate hydrothermal system in the west associated with a relatively shallower intrusive body, also defined by positive gravity values. This intrusion, which could be related to the cluster of volcanic domes located south of Bakilid Fault, may provide the heat that drives the hot springs at Kilbay and Alawihaw. It could also be possible that the Kilbay and Alawihaw springs originate from both systems. Based on the interpretation of the gravity and MT data, wells LB-1D and LB-5D lie closest to the intrusive, LB-313 and LB-4D are located in the center of the resource, while LB-2D and LB-6D lie along the margin or outside of the resource. The size of this resource, as defined by the 5 ohm-m MT low resistivity anomaly, is about 10 sq. km.« less

Brownian dynamics simulations with stiff finitely extensible nonlinear elastic-Fraenkel springs as approximations to rods in bead-rod models.

PubMed

Hsieh, Chih-Chen; Jain, Semant; Larson, Ronald G

2006-01-28

A very stiff finitely extensible nonlinear elastic (FENE)-Fraenkel spring is proposed to replace the rigid rod in the bead-rod model. This allows the adoption of a fast predictor-corrector method so that large time steps can be taken in Brownian dynamics (BD) simulations without over- or understretching the stiff springs. In contrast to the simple bead-rod model, BD simulations with beads and FENE-Fraenkel (FF) springs yield a random-walk configuration at equilibrium. We compare the simulation results of the free-draining bead-FF-spring model with those for the bead-rod model in relaxation, start-up of uniaxial extensional, and simple shear flows, and find that both methods generate nearly identical results. The computational cost per time step for a free-draining BD simulation with the proposed bead-FF-spring model is about twice as high as the traditional bead-rod model with the midpoint algorithm of Liu [J. Chem. Phys. 90, 5826 (1989)]. Nevertheless, computations with the bead-FF-spring model are as efficient as those with the bead-rod model in extensional flow because the former allows larger time steps. Moreover, the Brownian contribution to the stress for the bead-FF-spring model is isotropic and therefore simplifies the calculation of the polymer stresses. In addition, hydrodynamic interaction can more easily be incorporated into the bead-FF-spring model than into the bead-rod model since the metric force arising from the non-Cartesian coordinates used in bead-rod simulations is absent from bead-spring simulations. Finally, with our newly developed bead-FF-spring model, existing computer codes for the bead-spring models can trivially be converted to ones for effective bead-rod simulations merely by replacing the usual FENE or Cohen spring law with a FENE-Fraenkel law, and this convertibility provides a very convenient way to perform multiscale BD simulations.

Brownian dynamics simulations with stiff finitely extensible nonlinear elastic-Fraenkel springs as approximations to rods in bead-rod models

NASA Astrophysics Data System (ADS)

Hsieh, Chih-Chen; Jain, Semant; Larson, Ronald G.

2006-01-01

A very stiff finitely extensible nonlinear elastic (FENE)-Fraenkel spring is proposed to replace the rigid rod in the bead-rod model. This allows the adoption of a fast predictor-corrector method so that large time steps can be taken in Brownian dynamics (BD) simulations without over- or understretching the stiff springs. In contrast to the simple bead-rod model, BD simulations with beads and FENE-Fraenkel (FF) springs yield a random-walk configuration at equilibrium. We compare the simulation results of the free-draining bead-FF-spring model with those for the bead-rod model in relaxation, start-up of uniaxial extensional, and simple shear flows, and find that both methods generate nearly identical results. The computational cost per time step for a free-draining BD simulation with the proposed bead-FF-spring model is about twice as high as the traditional bead-rod model with the midpoint algorithm of Liu [J. Chem. Phys. 90, 5826 (1989)]. Nevertheless, computations with the bead-FF-spring model are as efficient as those with the bead-rod model in extensional flow because the former allows larger time steps. Moreover, the Brownian contribution to the stress for the bead-FF-spring model is isotropic and therefore simplifies the calculation of the polymer stresses. In addition, hydrodynamic interaction can more easily be incorporated into the bead-FF-spring model than into the bead-rod model since the metric force arising from the non-Cartesian coordinates used in bead-rod simulations is absent from bead-spring simulations. Finally, with our newly developed bead-FF-spring model, existing computer codes for the bead-spring models can trivially be converted to ones for effective bead-rod simulations merely by replacing the usual FENE or Cohen spring law with a FENE-Fraenkel law, and this convertibility provides a very convenient way to perform multiscale BD simulations.

Resistivity structure and geochemistry of the Jigokudani Valley hydrothermal system, Mt. Tateyama, Japan

NASA Astrophysics Data System (ADS)

Seki, Kaori; Kanda, Wataru; Tanbo, Toshiya; Ohba, Takeshi; Ogawa, Yasuo; Takakura, Shinichi; Nogami, Kenji; Ushioda, Masashi; Suzuki, Atsushi; Saito, Zenshiro; Matsunaga, Yasuo

2016-10-01

This study clarifies the hydrothermal system of Jigokudani Valley near Mt. Tateyama volcano in Japan by using a combination of audio-frequency magnetotelluric (AMT) survey and hot-spring water analysis in order to assess the potential of future phreatic eruptions in the area. Repeated phreatic eruptions in the area about 40,000 years ago produced the current valley morphology, which is now an active solfatara field dotted with hot springs and fumaroles indicative of a well-developed hydrothermal system. The three-dimensional (3D) resistivity structure of the hydrothermal system was modeled by using the results of an AMT survey conducted at 25 locations across the valley in 2013-2014. The model suggests the presence of a near-surface highly conductive layer of < 50 m in thickness across the entire valley, which is interpreted as a cap rock layer. Immediately below the cap rock is a relatively resistive body interpreted as a gas reservoir. Field measurements of temperature, pH, and electrical conductivity (EC) were taken at various hot springs across the valley, and 12 samples of hot-spring waters were analyzed for major ion chemistry and H2O isotopic ratios. All hot-spring waters had low pH and could be categorized into three types on the basis of the Cl-/SO 42 - concentration ratio, with all falling largely on a mixing line between magmatic fluids and local meteoric water (LMW). The geochemical analysis suggests that the hydrothermal system includes a two-phase zone of vapor-liquid. A comparison of the resistivity structure and the geochemically inferred structure suggests that a hydrothermal reservoir is present at a depth of approximately 500 m, from which hot-spring water differentiates into the three observed types. The two-phase zone appears to be located immediately beneath the cap rock structure. These findings suggest that the hydrothermal system of Jigokudani Valley exhibits a number of factors that could trigger a future phreatic eruption.

Fuel nozzle tube retention

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cihlar, David William; Melton, Patrick Benedict

A system for retaining a fuel nozzle premix tube includes a retention plate and a premix tube which extends downstream from an outlet of a premix passage defined along an aft side of a fuel plenum body. The premix tube includes an inlet end and a spring support feature which is disposed proximate to the inlet end. The premix tube extends through the retention plate. The spring retention feature is disposed between an aft side of the fuel plenum and the retention plate. The system further includes a spring which extends between the spring retention feature and the retention plate.

Instability of hooks during bacterial flagellar swimming

NASA Astrophysics Data System (ADS)

Jabbarzadeh, Mehdi; Fu, Henry C.; Henry Fu Team

2016-11-01

In bacteria, a flexible hook transmits torque from the rotary motor at the cell body to the flagellum. Previously, the hook has been modeled as a Kirchhoff rod between the cell body and rotating flagellum. To study effects of the hook's flexibility on the bacteria's swimming speed and trajectory for wide range hook stiffnesses and flagellum configurations, we develop an efficient simplified spring model for the hook by linearizing the Kirchhoff rod. We treat the hydrodynamics of the cell body and helical flagellum using resistance matrices calculated by the method of regularized Stokeslets. We investigate flagellar and swimming dynamics for a range of hook flexibilities and flagellar orientations relative to the cell body and compare the results to models without hook flexibility. We investigate in detail parameters corresponding to E. coli and Vibrio alginolyticus. Generally, the flagellum changes orientation relative to the cell body, undergoing an orbit with the period of the motor rotation. We find that as the hook stiffness decreases, steady-state orbits of the flagellum first become unstable before the hook buckles, which may suggest a new mechanism of flick initiation in run-reverse-flick motility. We also find that for some parameter ranges, there are multiple stable steady state orbits, which may have implications for the tumbling and turning of bacteria.

Investigation of membrane mechanics using spring networks: application to red-blood-cell modelling.

PubMed

Chen, Mingzhu; Boyle, Fergal J

2014-10-01

In recent years a number of red-blood-cell (RBC) models have been proposed using spring networks to represent the RBC membrane. Some results predicted by these models agree well with experimental measurements. However, the suitability of these membrane models has been questioned. The RBC membrane, like a continuum membrane, is mechanically isotropic throughout its surface, but the mechanical properties of a spring network vary on the network surface and change with deformation. In this work spring-network mechanics are investigated in large deformation for the first time via an assessment of the effect of network parameters, i.e. network mesh, spring type and surface constraint. It is found that a spring network is conditionally equivalent to a continuum membrane. In addition, spring networks are employed for RBC modelling to replicate the optical tweezers test. It is found that a spring network is sufficient for modelling the RBC membrane but strain-hardening springs are required. Moreover, the deformation profile of a spring network is presented for the first time via the degree of shear. It is found that spring-network deformation approaches continuous as the mesh density increases. Copyright © 2014 Elsevier B.V. All rights reserved.

Numerical study of groundwater flow cycling controlled by seawater/freshwater interaction in a coastal karst aquifer through conduit network using CFPv2.

PubMed

Xu, Zexuan; Hu, Bill X; Davis, Hal; Kish, Stephen

2015-11-01

In this study, a groundwater flow cycling in a karst springshed and an interaction between two springs, Spring Creek Springs and Wakulla Springs, through a subground conduit network are numerically simulated using CFPv2, the latest research version of MODFLOW-CFP (Conduit Flow Process). The Spring Creek Springs and Wakulla Springs, located in a marine estuary and 11 miles inland, respectively, are two major groundwater discharge spots in the Woodville Karst Plain (WKP), North Florida, USA. A three-phase conceptual model of groundwater flow cycling between the two springs and surface water recharge from a major surface creek (Lost Creek) was proposed in various rainfall conditions. A high permeable subground karst conduit network connecting the two springs was found by tracer tests and cave diving. Flow rate of discharge, salinity, sea level and tide height at Spring Creek Springs could significantly affect groundwater discharge and water stage at Wakulla Springs simultaneously. Based on the conceptual model, a numerical hybrid discrete-continuum groundwater flow model is developed using CFPv2 and calibrated by field measurements. Non-laminar flows in conduits and flow exchange between conduits and porous medium are implemented in the hybrid coupling numerical model. Time-variable salinity and equivalent freshwater head boundary conditions at the submarine spring as well as changing recharges have significant impacts on seawater/freshwater interaction and springs' discharges. The developed numerical model is used to simulate the dynamic hydrological process and quantitatively represent the three-phase conceptual model from June 2007 to June 2010. Simulated results of two springs' discharges match reasonably well to measurements with correlation coefficients 0.891 and 0.866 at Spring Creeks Springs and Wakulla Springs, respectively. The impacts of sea level rise on regional groundwater flow field and relationship between the inland springs and submarine springs are evaluated as well in this study. Copyright © 2015 Elsevier B.V. All rights reserved.

Numerical study of groundwater flow cycling controlled by seawater/freshwater interaction in a coastal karst aquifer through conduit network using CFPv2

NASA Astrophysics Data System (ADS)

Xu, Zexuan; Hu, Bill X.; Davis, Hal; Kish, Stephen

2015-11-01

In this study, a groundwater flow cycling in a karst springshed and an interaction between two springs, Spring Creek Springs and Wakulla Springs, through a subground conduit network are numerically simulated using CFPv2, the latest research version of MODFLOW-CFP (Conduit Flow Process). The Spring Creek Springs and Wakulla Springs, located in a marine estuary and 11 miles inland, respectively, are two major groundwater discharge spots in the Woodville Karst Plain (WKP), North Florida, USA. A three-phase conceptual model of groundwater flow cycling between the two springs and surface water recharge from a major surface creek (Lost Creek) was proposed in various rainfall conditions. A high permeable subground karst conduit network connecting the two springs was found by tracer tests and cave diving. Flow rate of discharge, salinity, sea level and tide height at Spring Creek Springs could significantly affect groundwater discharge and water stage at Wakulla Springs simultaneously. Based on the conceptual model, a numerical hybrid discrete-continuum groundwater flow model is developed using CFPv2 and calibrated by field measurements. Non-laminar flows in conduits and flow exchange between conduits and porous medium are implemented in the hybrid coupling numerical model. Time-variable salinity and equivalent freshwater head boundary conditions at the submarine spring as well as changing recharges have significant impacts on seawater/freshwater interaction and springs' discharges. The developed numerical model is used to simulate the dynamic hydrological process and quantitatively represent the three-phase conceptual model from June 2007 to June 2010. Simulated results of two springs' discharges match reasonably well to measurements with correlation coefficients 0.891 and 0.866 at Spring Creeks Springs and Wakulla Springs, respectively. The impacts of sea level rise on regional groundwater flow field and relationship between the inland springs and submarine springs are evaluated as well in this study.

State-space prediction of spring discharge in a karst catchment in southwest China

NASA Astrophysics Data System (ADS)

Li, Zhenwei; Xu, Xianli; Liu, Meixian; Li, Xuezhang; Zhang, Rongfei; Wang, Kelin; Xu, Chaohao

2017-06-01

Southwest China represents one of the largest continuous karst regions in the world. It is estimated that around 1.7 million people are heavily dependent on water derived from karst springs in southwest China. However, there is a limited amount of water supply in this region. Moreover, there is not enough information on temporal patterns of spring discharge in the area. In this context, it is essential to accurately predict spring discharge, as well as understand karst hydrological processes in a thorough manner, so that water shortages in this area could be predicted and managed efficiently. The objectives of this study were to determine the primary factors that govern spring discharge patterns and to develop a state-space model to predict spring discharge. Spring discharge, precipitation (PT), relative humidity (RD), water temperature (WD), and electrical conductivity (EC) were the variables analyzed in the present work, and they were monitored at two different locations (referred to as karst springs A and B, respectively, in this paper) in a karst catchment area in southwest China from May to November 2015. Results showed that a state-space model using any combinations of variables outperformed a classical linear regression, a back-propagation artificial neural network model, and a least square support vector machine in modeling spring discharge time series for karst spring A. The best state-space model was obtained by using PT and RD, which accounted for 99.9% of the total variation in spring discharge. This model was then applied to an independent data set obtained from karst spring B, and it provided accurate spring discharge estimates. Therefore, state-space modeling was a useful tool for predicting spring discharge in karst regions in southwest China, and this modeling procedure may help researchers to obtain accurate results in other karst regions.

46 CFR 162.017-3 - Materials, construction, and workmanship.

Code of Federal Regulations, 2010 CFR

2010-10-01

... serviceability. (b) Bodies of pressure-vacuum relief valves must be made of bronze or such corrosion-resistant..., and seats shall be made of bronze or such corrosion-resistant material as may be approved by the... springs shall be made of corrosion-resistant material. Springs plated with corrosion-resistant material...

Ongoing hydrothermal heat loss from the 1912 ash-flow sheet, Valley of Ten Thousand Smokes, Alaska

USGS Publications Warehouse

Hogeweg, N.; Keith, T.E.C.; Colvard, E.M.; Ingebritsen, S.E.

2005-01-01

The June 1912 eruption of Novarupta filled nearby glacial valleys on the Alaska Peninsula with ash-flow tuff (ignimbrite), and post-eruption observations of thousands of steaming fumaroles led to the name 'Valley of Ten Thousand Smokes' (VTTS). By the late 1980s most fumarolic activity had ceased, but the discovery of thermal springs in mid-valley in 1987 suggested continued cooling of the ash-flow sheet. Data collected at the mid-valley springs between 1987 and 2001 show a statistically significant correlation between maximum observed chloride (Cl) concentration and temperature. These data also show a statistically significant decline in the maximum Cl concentration. The observed variation in stream chemistry across the sheet strongly implies that most solutes, including Cl, originate within the area of the VTTS occupied by the 1912 deposits. Numerous measurements of Cl flux in the Ukak River just below the ash-flow sheet suggest an ongoing heat loss of ???250 MW. This represents one of the largest hydrothermal heat discharges in North America. Other hydrothermal discharges of comparable magnitude are related to heat obtained from silicic magma bodies at depth, and are quasi-steady on a multidecadal time scale. However, the VTTS hydrothermal flux is not obviously related to a magma body and is clearly declining. Available data provide reasonable boundary and initial conditions for simple transient modeling. Both an analytical, conduction-only model and a numerical model predict large rates of heat loss from the sheet 90 years after deposition.

Colour change in a structural ornament is related to individual quality, parasites and mating patterns in the blue tit

NASA Astrophysics Data System (ADS)

Badás, E. P.; Martínez, J.; Rivero-de Aguilar, J.; Ponce, C.; Stevens, M.; Merino, S.

2018-02-01

Carry-over effects refer to processes that occur in one season and influence fitness in the following. In birds, two costly activities, namely reproduction and moult, are restricted to a small time window, and sometimes overlap. Thus, colour in newly moulted feathers is likely to be affected by the costs of reproduction. Using models of bird vision we investigated male colour change in a free-living population of blue tits ( Cyanistes caeruleus) in three sampling occasions: spring 1, winter and spring 2. We related crown, tail, breast and cheek feather colouration after the moult (winter) to the intensity of infections by blood parasites during reproduction (spring 1). In the following spring (spring 2), we explored mating patterns with respect to changes in feather colour (springs 1 vs. 2). Males that were less intensely infected by the malaria parasite Plasmodium while breeding showed purer white cheek feathers in winter, which may indicate higher feather quality. Increased brightness in the white cheek was associated with better body condition during reproduction. In the following season, males with brighter cheeks paired with females that had noticeably brighter cheek patches compared to the male's previous mate. These results suggest that the conditions experienced during reproduction are likely to affect moult and thus feather colouration, at least in the white patch. High quality individuals may allocate resources efficiently during reproduction increasing future reproductive success through variation in mating patterns. Carry-over effects from reproduction might extend not only to the non-breeding phase, but also to the following breeding season.

Colour change in a structural ornament is related to individual quality, parasites and mating patterns in the blue tit.

PubMed

Badás, E P; Martínez, J; Rivero-de Aguilar, J; Ponce, C; Stevens, M; Merino, S

2018-02-06

Carry-over effects refer to processes that occur in one season and influence fitness in the following. In birds, two costly activities, namely reproduction and moult, are restricted to a small time window, and sometimes overlap. Thus, colour in newly moulted feathers is likely to be affected by the costs of reproduction. Using models of bird vision we investigated male colour change in a free-living population of blue tits (Cyanistes caeruleus) in three sampling occasions: spring 1, winter and spring 2. We related crown, tail, breast and cheek feather colouration after the moult (winter) to the intensity of infections by blood parasites during reproduction (spring 1). In the following spring (spring 2), we explored mating patterns with respect to changes in feather colour (springs 1 vs. 2). Males that were less intensely infected by the malaria parasite Plasmodium while breeding showed purer white cheek feathers in winter, which may indicate higher feather quality. Increased brightness in the white cheek was associated with better body condition during reproduction. In the following season, males with brighter cheeks paired with females that had noticeably brighter cheek patches compared to the male's previous mate. These results suggest that the conditions experienced during reproduction are likely to affect moult and thus feather colouration, at least in the white patch. High quality individuals may allocate resources efficiently during reproduction increasing future reproductive success through variation in mating patterns. Carry-over effects from reproduction might extend not only to the non-breeding phase, but also to the following breeding season.

Climate and population density drive changes in cod body size throughout a century on the Norwegian coast

PubMed Central

Rogers, Lauren A.; Stige, Leif C.; Olsen, Esben M.; Knutsen, Halvor; Chan, Kung-Sik; Stenseth, Nils Chr.

2011-01-01

Understanding how populations respond to changes in climate requires long-term, high-quality datasets, which are rare for marine systems. We estimated the effects of climate warming on cod lengths and length variability using a unique 91-y time series of more than 100,000 individual juvenile cod lengths from surveys that began in 1919 along the Norwegian Skagerrak coast. Using linear mixed-effects models, we accounted for spatial population structure and the nested structure of the survey data to reveal opposite effects of spring and summer warming on juvenile cod lengths. Warm summer temperatures in the coastal Skagerrak have limited juvenile growth. In contrast, warmer springs have resulted in larger juvenile cod, with less variation in lengths within a cohort, possibly because of a temperature-driven contraction in the spring spawning period. A density-dependent reduction in length was evident only at the highest population densities in the time series, which have rarely been observed in the last decade. If temperatures rise because of global warming, nonlinearities in the opposing temperature effects suggest that negative effects of warmer summers will increasingly outweigh positive effects of warmer springs, and the coastal Skagerrak will become ill-suited for Atlantic cod. PMID:21245301

Alteration and geochemical zoning in Bodie Bluff, Bodie mining district, eastern California

USGS Publications Warehouse

Herrera, P.A.; Closs, L.G.; Silberman, M.L.

1993-01-01

Banded, epithermal quartz-adularia veins have produced about 1.5 million ounces of gold and 7 million ounces of silver from the Bodie mining district, eastern California. The veins cut dacitic lava flows, pyroclastic rocks and intrusions. Sinter boulders occur in a graben structure at the top of Bodie Bluff and fragments of sinter and mineralized quartz veins occur in hydrothermal breccias nearby. Explosive venting evidently was part of the evolution of the ore-forming geothermal systems which, at one time, must had reached the paleosurface. Previous reconnaissance studies at Bodie Bluff suggested that the geometry of alteration mineral assemblages and distribution of some of the major and trace elements throughout the system correspond to those predicted by models of hot-spring, volcanic rock hosted precious metal deposits (Silberman, 1982; Silberman and Berger, 1985). The current study was undertaken to evaluate these sugestions further. About 500 samples of quartz veins and altered rocks, including sinter, collected over a vertical extent of 200 meters within Bodie Bluff were petrographically examined and chemically analyzed for trace elements by emission spectrographic and atomic absorption methods. Sixty-five samples were analyzed for major elements by X-ray fluorescence methods. The results of these analyses showed that, in general, alteration mineral assemblage and vertical geochemical zoning patterns follow those predicted for hot-spring deposits, but that geochemical zoning patterns for sinter and quartz veins (siliceous deposits), and altered wall rocks are not always similar. The predicted depth-concentration patterns for some elements, notably Au, Ag, Hg, and Tl in quartz veins, and Hg, As and Ag in wall rocks were not as expected, or were perturbed by the main ore producing zone. For both quartz veins and altered wall rocks, the main ore zone had elevated metal contents. Increased concentration of many of these elements could indicate proximity to this zone. However, irregularities in the distribution of some key elements, such as Au and Ag, relative to the predictive models suggest that a larger suite of elements be considered for exploration for ore zones within the district. ?? 1993.

Multi-Body Analysis of a Tiltrotor Configuration

NASA Technical Reports Server (NTRS)

Ghiringhelli, G. L.; Masarati, P.; Mantegazza, P.; Nixon, M. W.

1997-01-01

The paper describes the aeroelastic analysis of a tiltrotor configuration. The 1/5 scale wind tunnel semispan model of the V-22 tiltrotor aircraft is considered. The analysis is performed by means of a multi-body code, based on an original formulation. The differential equilibrium problem is stated in terms of first order differential equations. The equilibrium equations of every rigid body are written, together with the definitions of the momenta. The bodies are connected by kinematic constraints, applied in form of Lagrangian multipliers. Deformable components are mainly modelled by means of beam elements, based on an original finite volume formulation. Multi-disciplinar problems can be solved by adding user-defined differential equations. In the presented analysis the equations related to the control of the swash-plate of the model are considered. Advantages of a multi-body aeroelastic code over existing comprehensive rotorcraft codes include the exact modelling of the kinematics of the hub, the detailed modelling of the flexibility of critical hub components, and the possibility to simulate steady flight conditions as well as wind-up and maneuvers. The simulations described in the paper include: 1) the analysis of the aeroelastic stability, with particular regard to the proprotor/pylon instability that is peculiar to tiltrotors, 2) the determination of the dynamic behavior of the system and of the loads due to typical maneuvers, with particular regard to the conversion from helicopter to airplane mode, and 3) the stress evaluation in critical components, such as the pitch links and the conversion downstop spring.

Trace elements in mineral separates of the Pena Blanca Spring aubrite - Implications for the evolution of the aubrite parent body

NASA Technical Reports Server (NTRS)

Lodders, K.; Palme, H.; Wlotzka, F.

1993-01-01

A detailed chemical study is conducted of the Pena Blanca Spring aubrite in order to clarify both the origin of the aubrite parent body (APB) and its relation to the enstatite chondrites. The distribution of REE among aubritic minerals cannot be the result of fractional distillation, which would occur if high degrees of partial melting had occurred on the APB. The REE distributions instead indicate a complete equilibrium of oldhamite and other phases, so that a brief nonequilibrium melting episode must have led to the segregation of metal and sulfides.

A springy pendulum could describe the swing leg kinetics of human walking.

PubMed

Song, Hyunggwi; Park, Heewon; Park, Sukyung

2016-06-14

The dynamics of human walking during various walking conditions could be qualitatively captured by the springy legged dynamics, which have been used as a theoretical framework for bipedal robotics applications. However, the spring-loaded inverted pendulum model describes the motion of the center of mass (CoM), which combines the torso, swing and stance legs together and does not explicitly inform us as to whether the inter-limb dynamics share the springy legged dynamics characteristics of the CoM. In this study, we examined whether the swing leg dynamics could also be represented by springy mechanics and whether the swing leg stiffness shows a dependence on gait speed, as has been observed in CoM mechanics during walking. The swing leg was modeled as a spring-loaded pendulum hinged at the hip joint, which is under forward motion. The model parameters of the loaded mass were adopted from body parameters and anthropometric tables, whereas the free model parameters for the rest length of the spring and its stiffness were estimated to best match the data for the swing leg joint forces. The joint forces of the swing leg were well represented by the springy pendulum model at various walking speeds with a regression coefficient of R(2)>0.8. The swing leg stiffness increased with walking speed and was correlated with the swing frequency, which is consistent with previous observations from CoM dynamics described using the compliant leg. These results suggest that the swing leg also shares the springy dynamics, and the compliant walking model could be extended to better present swing leg dynamics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Soft tissue modelling with conical springs.

PubMed

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

a Study on Strain Rate Effect in Collision Analysis of Rolling STOCK

NASA Astrophysics Data System (ADS)

Kim, Seung Rok; Koo, Jeong Seo

In this paper, the strain rate effect of energy absorption members in rolling stock is studied using the virtual testing model (VTM) for Korean high speed train (KHST). The VTM of KHST was simulated for two different strain rate conditions. The VTM is composed of FE models for structures, and nonlinear spring/damper models for dynamic components. To simplify numerical model for the full rake KHST, the first three units consist of full flexible multi-body dynamic models, and the remainder does 1-D spring/damper/mass models. To evaluate the strain rate effect of KHST, the crash simulation was performed under the accident scenario for a collision with a rigid mass of 15 tons at 110kph. The numerical results show that the overall crash response of the train is not largely affected as much as expected, but individual components have some different deformations according to strain rate. The deformation of the front end structure without strain rate effect is larger than that with it. However, the deformation of the rear end structure without strain rate effect is smaller than that with it. Finally, the intrusion of the driver's cabin is overestimated for no strain rate effect when compared to the case with it.

Map showing springs in the Salina quadrangle, Utah

USGS Publications Warehouse

Covington, Harry R.

1972-01-01

A spring is “a place where, without the agency of man, water flows from a rock or soil upon the land or into a body of surface water” (Meinzer, 1923, p. 48).About 450 springs are located on this map. Locations and names are from the U.S. Forest Service maps (1963, 1964) and from topographic maps of the U.S. Geological Survey, both published and in preparation. There is considerable variation in geological occurrence of the springs and in quantity and chemical quality of the water that issues from them. Springs in the Salina quadrangle are more abundant where annual precipitation is 16 inches or more, although there are many springs in arid parts of the quadrangle as well.In the Salina quadrangle, springs are used most commonly for watering livestock. They are used also for irrigation and for domestic and municipal water supply. Several communities in Rabbit Valley, Grass Valley, and Sevier Valley depend on springs for all or part of their water supply.Quantity and quality of water are shown for those few springs for which data are available (Mundorff, 1971). Caution must be used in drinking from springs, especially in arid areas; the water commonly tastes bad and may cause illness.

Shape memory thermal conduction switch

NASA Technical Reports Server (NTRS)

Krishnan, Vinu (Inventor); Vaidyanathan, Rajan (Inventor); Notardonato, William U. (Inventor)

2010-01-01

A thermal conduction switch includes a thermally-conductive first member having a first thermal contacting structure for securing the first member as a stationary member to a thermally regulated body or a body requiring thermal regulation. A movable thermally-conductive second member has a second thermal contacting surface. A thermally conductive coupler is interposed between the first member and the second member for thermally coupling the first member to the second member. At least one control spring is coupled between the first member and the second member. The control spring includes a NiTiFe comprising shape memory (SM) material that provides a phase change temperature <273 K, a transformation range <40 K, and a hysteresis of <10 K. A bias spring is between the first member and the second member. At the phase change the switch provides a distance change (displacement) between first and second member by at least 1 mm, such as 2 to 4 mm.

Research note: the performance of spring- and summer-reared broilers as affected by precision beak trimming at seven days of age.

PubMed

Christmas, R B

1993-12-01

In each of two duplicate trials approximately 2,500 day-old Peterson x Arbor Acres straight-run broiler chicks were equally divided between two treatments of three pens each. Treatment 1 was maintained as controls (C), and Treatment 2 birds were precision beak-trimmed (PBT) at 7 days of age. Feed and water were supplied for ad libitum consumption to both groups. Trials 1 and 2 were initiated in March and June, respectively. Performance of spring-reared broilers were comparable regardless of beak trimming procedure, except that PBT broilers experienced slightly higher mortality after PBT. Final body weights of the summer-reared broilers were 15% lower than those reared in the spring. Additionally, PBT resulted in significantly reduced final body weights and feed intake. There were no significant differences in mortality or feed conversion due to PBT.

Predicting characteristics of rainfall driven estrogen runoff and transport from swine AFO spray fields.

PubMed

Lee, Boknam; Kullman, Seth W; Yost, Erin E; Meyer, Michael T; Worley-Davis, Lynn; Williams, C Michael; Reckhow, Kenneth H

2015-11-01

Animal feeding operations (AFOs) have been implicated as potentially major sources of estrogenic contaminants into the aquatic environment due to the relatively minimal treatment of waste and potential mobilization and transport of waste components from spray fields. In this study a Bayesian network (BN) model was developed to inform management decisions and better predict the transport and fate of natural steroidal estrogens from these sites. The developed BN model integrates processes of surface runoff and sediment loss with the modified universal soil loss equation (MUSLE) and the soil conservation service curve number (SCS-CN) runoff model. What-if scenario simulations of lagoon slurry wastes to the spray fields were conducted for the most abundant natural estrogen estrone (E1) observed in the system. It was found that E1 attenuated significantly after 2 months following waste slurry application in both spring and summer seasons, with the overall attenuation rate predicted to be higher in the summer compared to the spring. Using simulations of rainfall events in conjunction with waste slurry application rates, it was predicted that the magnitude of E1 runoff loss is significantly higher in the spring as compared to the summer months, primarily due to spray field crop management plans. Our what-if scenario analyses suggest that planting Bermuda grass in the spray fields is likely to reduce runoff losses of natural estrogens near the water bodies and ecosystems, as compared to planting of soybeans. Copyright © 2015 Elsevier B.V. All rights reserved.

Predicting Characteristics of Rainfall Driven Estrogen Runoff and Transport from Swine AFO Spray Fields

PubMed Central

Lee, Boknam; Kullman, Seth W.; Yost, Erin E.; Meyer, Michael T.; Worley-Davis, Lynn; Williams, C. Michael; Reckhow, Kenneth H.

2017-01-01

Animal feeding operations (AFOs) have been implicated as potentially major sources of estrogenic contaminants into the aquatic environment due to the relatively minimal treatment of waste and potential mobilization and transport of waste components from spray fields. In this study a Bayesian network (BN) model was developed to inform management decisions and better predict the transport and fate of natural steroidal estrogens from these sites. The developed BN model integrates processes of surface runoff and sediment loss with the modified universal soil loss equation (MUSLE) and the soil conservation service curve number (SCS-CN) runoff model. What-if scenario simulations of lagoon slurry wastes to the spray fields were conducted for the most abundant natural estrogen estrone (E1) observed in the system. It was found that E1 attenuated significantly after 2 months following waste slurry application in both spring and summer seasons, with the overall attenuation rate predicted to be higher in the summer compared to the spring. Using simulations of rainfall events in conjunction with waste slurry application rates, it was predicted that the magnitude of E1 runoff loss is significantly higher in the spring as compared to the summer months, primarily due to spray field crop management plans. Our what-if scenario analyses suggest that planting Bermuda grass in the spray fields is likely to reduce runoff losses of natural estrogens near the water bodies and ecosystems, as compared to planting of soybeans. PMID:26102057

Insights into the factors responsible for curative effects of Aab-E-Shifa Spring Hasan Abdal (Pakistan)

NASA Astrophysics Data System (ADS)

ur Rahman, Sami; Bilal, Salma

2017-07-01

Springs are the gifts of nature on the earth as they contribute about eighty essential nutrients that are involved in more than 7000 enzymatic processes in the human body. European balneologists have recommended spring mineral waters for different therapeutic applications. In the present investigation, Aab- e- Shifa (Punjab Pakistan) spring water was analyzed due to its therapeutic behavior in the healing of various skin diseases via atomic absorption spectroscopy (AAS). It was found that besides other important minerals (Ca, Mg, K, and Na), the spring water contains the most significant antioxidant, i.e., Zn which is probably one of the major features of the curative behavior of Aab- e- Shifa. Other trace elements (Cr, Cd, Ni, Mn, Fe, and Cu) were also found to be present in the spring water under the permissible limits of various national and international organizations.

Transient Postseismic Relaxation With Burger's Body Viscoelasticity

NASA Astrophysics Data System (ADS)

Hetland, E. A.; Hager, B. H.; O'Connell, R. J.

2002-12-01

Typical models used to investigate postseismic deformation are composed of an elastic layer over a Maxwell viscoelastic region. Geodetic observations made after a number of large earthquakes show a rapid exponential decay in postseismic velocity immediately after the rupture, followed by a more slowly decaying (or constant) velocity at a later time. Models of a Maxwell viscoelastic interior predict a single exponential postseismic velocity relaxation. To account for observed rapid, short-term relaxation decay, surprisingly low viscosities in the lower-crust or upper-mantle have been proposed. To model the difference in short and long time decay rates, the Maxwell element is sometimes modified to have a non-linear rheology, which results in a lower effective viscosity immediately after the rupture, evolving to a higher effective viscosity as the co-seismic stresses relax. Incorporation of models of after-slip in the lower crust on a down-dip extension of the fault have also had some success at modeling the above observations. When real rocks are subjected to a sudden change in stress or strain, e.g., that caused by an earthquake, they exhibit a transient response. The transient deformation is typically accommodated by grain boundary sliding and the longer-time deformation is accommodated by motion of dislocations. Both a short-term transient response and long-term steady creep are exhibited by a Burger's body, a Maxwell element (a spring in series with a viscous dash-pot) in series with a Voigt element (a spring in parallel with a viscous dash-pot). Typically the (transient) viscosity of the Voigt element is 10 - 100 times less than the (steady) viscosity of the Maxwell element. Thus, with a Burger's body, stress relaxation is a superposition of two exponential decays. For a model composed of an elastic layer over a viscoelastic region, the coseismic changes in stress (and strain) depend only on the elastic moduli, and are independent of the description of the viscous component of the rheology. In a Burger's body model of viscoelasticity, if the viscosity of the Voigt element is much less than that of the Maxwell element, the initial relaxation time is given by the decay time τ = η {Voigt}}/G{ {Maxwell}. Whereas, for a Maxwell rheology, the initial relaxation time is given by τ = η {Maxwell}}/G{ {Maxwell}. For both models, the initial spatial distribution of stresses is the same, which results in identical initial spatial distribution of velocities. Thus it is easy to mistake the transient response of a Burger's body for that of a Maxwell rheology with unrealistically low viscosity. Only later in the seismic cycle do the spatial patterns of velocity differ for the two rheologies.

Gender differences in active musculoskeletal stiffness. Part II. Quantification of leg stiffness during functional hopping tasks.

PubMed

Granata, K P; Padua, D A; Wilson, S E

2002-04-01

Leg stiffness was compared between age-matched males and females during hopping at preferred and controlled frequencies. Stiffness was defined as the linear regression slope between the vertical center of mass (COM) displacement and ground-reaction forces recorded from a force plate during the stance phase of the hopping task. Results demonstrate that subjects modulated the vertical displacement of the COM during ground contact in relation to the square of hopping frequency. This supports the accuracy of the spring-mass oscillator as a representative model of hopping. It also maintained peak vertical ground-reaction load at approximately three times body weight. Leg stiffness values in males (33.9+/-8.7 kN/m) were significantly (p<0.01) greater than in females (26.3+/-6.5 kN/m) at each of three hopping frequencies, 3.0, 2.5 Hz, and a preferred hopping rate. In the spring-mass oscillator model leg stiffness and body mass are related to the frequency of motion. Thus male subjects necessarily recruited greater leg stiffness to drive their heavier body mass at the same frequency as the lighter female subjects during the controlled frequency trials. However, in the preferred hopping condition the stiffness was not constrained by the task because frequency was self-selected. Nonetheless, both male and female subjects hopped at statistically similar preferred frequencies (2.34+/-0.22 Hz), therefore, the females continued to demonstrate less leg stiffness. Recognizing the active muscle stiffness contributes to biomechanical stability as well as leg stiffness, these results may provide insight into the gender bias in risk of musculoskeletal knee injury.

Modeling anthropogenic boron in groundwater flow and discharge at Volusia Blue Spring (Florida, USA)

NASA Astrophysics Data System (ADS)

Reed, Erin M.; Wang, Dingbao; Duranceau, Steven J.

2017-01-01

Volusia Blue Spring (VBS) is the largest spring along the St. Johns River in Florida (USA) and the spring pool is refuge for hundreds of manatees during winter months. However, the water quality of the spring flow has been degraded due to urbanization in the past few decades. A three-dimensional contaminant fate and transport model, utilizing MODFLOW-2000 and MT3DMS, was developed to simulate boron transport in the Upper Florida Aquifer, which sustains the VBS spring discharge. The VBS model relied on information and data related to natural water features, rainfall, land use, water use, treated wastewater discharge, septic tank effluent flows, and fertilizers as inputs to simulate boron transport. The model was calibrated against field-observed water levels, spring discharge, and analysis of boron in water samples. The calibrated VBS model yielded a root-mean-square-error value of 1.8 m for the head and 17.7 μg/L for boron concentrations within the springshed. Model results show that anthropogenic boron from surrounding urbanized areas contributes to the boron found at Volusia Blue Spring.

Dropouts, Stopouts, Optouts at Del Mar College: Spring 1991. Report of a Joint Research Project.

ERIC Educational Resources Information Center

Luckie, Jo Ann I.; Bonham, L. Adrianne

A research project investigated 2,313 persons who attended Del Mar College (Texas) during fall 1990 but did not enroll for spring 1991. Four sets of data were collected: (1) limited demographic information on the total student body; (2) demographic information drawn from school records to describe all nonreturnees; (3) demographic information…

Relationship between body condition of American alligators and water depth in the Everglades, Florida

USGS Publications Warehouse

Fujisaki, Ikuko; Rice, Kenneth G.; Pearlstine, Leonard G.; Mazzotti, Frank J.

2009-01-01

Feeding opportunities of American alligators (Alligator mississippiensis) in freshwater wetlands in south Florida are closely linked to hydrologic conditions. In the Everglades, seasonally and annually fluctuating surface water levels affect populations of aquatic organisms that alligators consume. Since prey becomes more concentrated when water depth decreases, we hypothesized an inverse relationship between body condition and water depth in the Everglades. On average, condition of adult alligators in the dry season was significantly higher than in the wet season, but this was not the case for juveniles/subadults. The correlation between body condition and measured water depth at capture locations was weak; however, there was a significant negative correlation between the condition and predicted water depth prior to capture for all animals except for spring juveniles/subadults which had a weak positive condition-water depth relationship. Overall, a relatively strong inverse correlation occurred at 10-49 days prior to the capture day, suggesting that current body condition of alligators may depend on feeding opportunities during that period. Fitted regression of body condition on water depth (mean depth of 10 days when condition-water depth correlation was greatest) resulted in a significantly negative slope, except for spring adult females and spring juveniles/subadults for which slopes were not significantly different from zero. Our results imply that water management practices may be critical for alligators in the Everglades since water depth can affect animal condition in a relatively short period of time.

Spring distributions and relationships with land cover and hydrogeologic strata in a karst landscape in Winona County, Minnesota, USA

USGS Publications Warehouse

Williams, M.A.; Vondracek, B.

2010-01-01

Karst aquifers are important groundwater resources, but are vulnerable to contamination due to relatively rapid subsurface transport. Springs, points where the landscape and water table intersect and cold groundwater discharges, link aquifer systems with land surfaces and water bodies. As such, in many regions, they are critical to the viability of lakes, streams and cold-water fish communities. An understanding of where springs are located is important to watershed, fishery and environmental management efforts in karst regions. To better understand spatial distribution of springs and as a potential method for identifying variables that characterize locations of springs for improved land and watershed management, a nearest-neighbor analysis and a discriminant function analysis (DFA) of springs were conducted in Winona County, Minnesota USA, a karst landscape. Nearestneighbor analysis examined the spatial spring distribution. Twenty-two variables describing the locations of springs were analyzed to ascertain their ability to discriminate correct aquifer unit or bedrock unit classification for each spring. Springs were clumped with the highest densities in the lowest elevations. Springs were correctly assigned to aquifer units and bedrock units with eight and 11 landscape variables, respectively. Forest land cover was the only land cover type contributing to spring discrimination. Consideration of upland human activities, particularly in forested areas, on spring discharge along with a better understanding of characteristics describing spring locations could lead to better management activities that locate and protect springs and their important contributions to regional ecohydrology. ?? 2010 Springer-Verlag.

Spring distribution in Winona County, Minnesota, USA and the relationship with geologic strata in a karst landscape

USGS Publications Warehouse

Vondracek, Bruce C.; Williams, Mary A.

2010-01-01

Karst aquifers are important groundwater resources, but are vulnerable to contamination due to relatively rapid subsurface transport. Springs, points where the landscape and water table intersect and cold groundwater discharges, link aquifer systems with land surfaces and water bodies. As such, in many regions, they are critical to the viability of lakes, streams and cold-water fish communities. An understanding of where springs are located is important to watershed, fishery and environmental management efforts in karst regions. To better understand spatial distribution of springs and as a potential method for identifying variables that characterize locations of springs for improved land and watershed management, a nearest-neighbor analysis and a discriminant function analysis (DFA) of springs were conducted in Winona County, Minnesota, USA, a karst landscape. Nearest-neighbor analysis examined the spatial spring distribution. Twenty-two variables describing the locations of springs were analyzed to ascertain their ability to discriminate correct aquifer unit or bedrock unit classification for each spring. Springs were clumped with the highest densities in the lowest elevations. Springs were correctly assigned to aquifer units and bedrock units with eight and 11 landscape variables, respectively. Forest land cover was the only land cover type contributing to spring discrimination. Consideration of upland human activities, particularly in forested areas, on spring discharge along with a better understanding of characteristics describing spring locations could lead to better management activities that locate and protect springs and their important contributions to regional ecohydrology.

Unsteady locomotion: integrating muscle function with whole body dynamics and neuromuscular control

PubMed Central

Biewener, Andrew A.; Daley, Monica A.

2009-01-01

Summary By integrating studies of muscle function with analysis of whole body and limb dynamics, broader appreciation of neuromuscular function can be achieved. Ultimately, such studies need to address non-steady locomotor behaviors relevant to animals in their natural environments. When animals move slowly they likely rely on voluntary coordination of movement involving higher brain centers. However, when moving fast, their movements depend more strongly on responses controlled at more local levels. Our focus here is on control of fast-running locomotion. A key observation emerging from studies of steady level locomotion is that simple spring-mass dynamics, which help to economize energy expenditure, also apply to stabilization of unsteady running. Spring-mass dynamics apply to conditions that involve lateral impulsive perturbations, sudden changes in terrain height, and sudden changes in substrate stiffness or damping. Experimental investigation of unsteady locomotion is challenging, however, due to the variability inherent in such behaviors. Another emerging principle is that initial conditions associated with postural changes following a perturbation define different context-dependent stabilization responses. Distinct stabilization modes following a perturbation likely result from proximo-distal differences in limb muscle architecture, function and control strategy. Proximal muscles may be less sensitive to sudden perturbations and appear to operate, in such circumstances, under feed-forward control. In contrast, multiarticular distal muscles operate, via their tendons, to distribute energy among limb joints in a manner that also depends on the initial conditions of limb contact with the ground. Intrinsic properties of these distal muscle–tendon elements, in combination with limb and body dynamics, appear to provide rapid initial stabilizing mechanisms that are often consistent with spring-mass dynamics. These intrinsic mechanisms likely help to simplify the neural control task, in addition to compensating for delays inherent to subsequent force- and length-dependent neural feedback. Future work will benefit from integrative biomechanical approaches that employ a combination of modeling and experimental techniques to understand how the elegant interplay of intrinsic muscle properties, body dynamics and neural control allows animals to achieve stability and agility over a variety of conditions. PMID:17704070

Symplectic analysis of vertical random vibration for coupled vehicle track systems

NASA Astrophysics Data System (ADS)

Lu, F.; Kennedy, D.; Williams, F. W.; Lin, J. H.

2008-10-01

A computational model for random vibration analysis of vehicle-track systems is proposed and solutions use the pseudo excitation method (PEM) and the symplectic method. The vehicle is modelled as a mass, spring and damping system with 10 degrees of freedom (dofs) which consist of vertical and pitching motion for the vehicle body and its two bogies and vertical motion for the four wheelsets. The track is treated as an infinite Bernoulli-Euler beam connected to sleepers and hence to ballast and is regarded as a periodic structure. Linear springs couple the vehicle and the track. Hence, the coupled vehicle-track system has only 26 dofs. A fixed excitation model is used, i.e. the vehicle does not move along the track but instead the track irregularity profile moves backwards at the vehicle velocity. This irregularity is assumed to be a stationary random process. Random vibration theory is used to obtain the response power spectral densities (PSDs), by using PEM to transform this random multiexcitation problem into a deterministic harmonic excitation one and then applying symplectic solution methodology. Numerical results for an example include verification of the proposed method by comparing with finite element method (FEM) results; comparison between the present model and the traditional rigid track model and; discussion of the influences of track damping and vehicle velocity.

Relationships between annual cycles of testosterone, corticosterone, and body condition in male red-spotted garter snakes, Thamnophis sirtalis concinnus.

PubMed

Moore, I T; Lerner, J P; Lerner, D T; Mason, R T

2000-01-01

Over a 2-yr period, we investigated the annual cycles of plasma testosterone and corticosterone and the relationships between these hormones and body condition in a wild population of male red-spotted garter snakes, Thamnophis sirtalis concinnus. In the 10 mo that were sampled, a peak in testosterone was observed in late summer during gametogenesis and declining through the spring breeding period. Corticosterone and testosterone cycles were positively correlated, in contrast to many vertebrates, suggesting the lack of a direct negative interaction between the two hormones. Body condition, defined as the residual of the regression of mass on snout-vent length, also cycled annually, with individuals being more robust during the summer than during the spring or fall. Individuals with a positive body condition had significantly lower plasma levels of corticosterone than did individuals with a negative body condition, supporting the energetic role of glucocorticoids. There was no relationship between body condition and testosterone. This study suggests that annual cycles of testosterone, corticosterone, and body condition can be associated with one another, and considering all three simultaneously is necessary to understand their control and function.

Fat dynamics of arctic-nesting sandpipers during spring in mid-continental North America

USGS Publications Warehouse

Krapu, G.L.; Eldridge, J.L.; Gratto-Trevor, C. L.; Buhl, D.A.

2006-01-01

We measured fresh body mass, total body fat, and fat-free dry mass (FFDM) of three species of Arctic-nesting calidrid sandpipers (Baird's Sandpiper [Calidris bairdii], hereafter “BASA”; Semipalmated Sandpiper [C. pusilla], hereafter “SESA”; and White-rumped Sandpiper [C. fuscicollis], hereafter “WRSA”) during spring stopovers in the Prairie Pothole Region (PPR) of North Dakota, and evaluated the contribution of stored fat to (1) energy requirements for migration to their Arctic-breeding grounds and (2) nutrient needs for reproduction. All spring migrant WRSA (n = 124) and BASA (n = 111), and all but 2 of 99 SESA we collected were ≥2 years old. Male and female BASA migrated through North Dakota concurrently, male SESA averaged earlier than females, and WRSA males preceded females. Fat indices (ratio of fat to FFDM) of male and female SESA and WRSA averaged approximately twice those of male and female BASA. Total body fat of male and female BASA increased with date in spring 1980, but not in 1981; slopes were similar for both sexes each year. Male and female SESA arrived lean in 1980 and 1981, and total body fat increased with date in both years, with similar slopes for all combinations of sex and year. Male and female WRSA arrived lean in 1980–1981 and 1981, respectively, and total body fat increased with date, whereas females arrived with fat reserves already acquired in 1980. Interspecific and sex differences in migration schedules probably contributed to variation in fat storage patterns by affecting maintenance energy costs and food availability. Estimated flight ranges of BASA suggest that few could have met their energy needs for migration to the breeding grounds exclusively from fat stored by the time of departure from North Dakota. Estimated flight ranges of SESA and WRSA, along with fresh body masses of both species when live-trapped on or near their breeding grounds in northern Canada, suggest that major parts of both populations stored adequate fat by departure from temperate mid-continental North America to meet their energy requirements for migration and part of their nutrient needs for reproduction.

A Systematic Approach to Predicting Spring Force for Sagittal Craniosynostosis Surgery.

PubMed

Zhang, Guangming; Tan, Hua; Qian, Xiaohua; Zhang, Jian; Li, King; David, Lisa R; Zhou, Xiaobo

2016-05-01

Spring-assisted surgery (SAS) can effectively treat scaphocephaly by reshaping crania with the appropriate spring force. However, it is difficult to accurately estimate spring force without considering biomechanical properties of tissues. This study presents and validates a reliable system to accurately predict the spring force for sagittal craniosynostosis surgery. The authors randomly chose 23 patients who underwent SAS and had been followed for at least 2 years. An elastic model was designed to characterize the biomechanical behavior of calvarial bone tissue for each individual. After simulating the contact force on accurate position of the skull strip with the springs, the finite element method was applied to calculating the stress of each tissue node based on the elastic model. A support vector regression approach was then used to model the relationships between biomechanical properties generated from spring force, bone thickness, and the change of cephalic index after surgery. Therefore, for a new patient, the optimal spring force can be predicted based on the learned model with virtual spring simulation and dynamic programming approach prior to SAS. Leave-one-out cross-validation was implemented to assess the accuracy of our prediction. As a result, the mean prediction accuracy of this model was 93.35%, demonstrating the great potential of this model as a useful adjunct for preoperative planning tool.

Scalability of an endoluminal spring for distraction enterogenesis.

PubMed

Rouch, Joshua D; Huynh, Nhan; Scott, Andrew; Chiang, Elvin; Wu, Benjamin M; Shekherdimian, Shant; Dunn, James C Y

2016-12-01

Techniques of distraction enterogenesis have been explored to provide increased intestinal length to treat short bowel syndrome (SBS). Self-expanding, polycaprolactone (PCL) springs have been shown to lengthen bowel in small animal models. Their feasibility in larger animal models is a critical step before clinical use. Juvenile mini-Yucatan pigs underwent jejunal isolation or blind ending Roux-en-y jejunojejunostomy with insertion of either a PCL spring or a sham PCL tube. Extrapolated from our spring characteristics in rodents, proportional increases in spring constant and size were made for porcine intestine. Jejunal segments with 7mm springs with k between 9 and 15N/m demonstrated significantly increased lengthening in isolated segment and Roux-en-y models. Complications were noted in only two animals, both using high spring constant k>17N/m. Histologically, lengthened segments in the isolated and Roux models demonstrated significantly increased muscularis thickness and crypt depth. Restoration of lengthened, isolated segments back into continuity was technically feasible after 6weeks. Self-expanding, endoluminal PCL springs, which exert up to 0.6N force, safely achieve significant intestinal lengthening in a translatable, large-animal model. These spring characteristics may provide a scalable model for the treatment of SBS in children. Copyright © 2016 Elsevier Inc. All rights reserved.

A Study of Running Safety and Ride Comfort of Floating Tracks for High-Speed Train

NASA Astrophysics Data System (ADS)

Watanabe, Tsutomu; Sogabe, Masamichi; Yamazaki, Takayuki

In order to reduce train-induced vibration, many floating tracks have been used, however, for only low-speed trains because we are not sure whether riding comfort and running safety can be maintained on floating tracks for high speed train. The authors, in this study, carried out an analysis of dynamic response and running quality of various floating tracks for high-speed train like Shinkansen. We used a simulation program, DIASTARS for the analysis. In this program, the Shinkansen vehicle is represented by a model of three dimensions consisting of a body, two trucks, and four wheelsets connected to each other with springs and dampers. The floating tracks were modeled by three-dimensional finite element method. In this study, the wheel load fluctuation and vehicle body accelerations were investigated by a dynamic interaction analysis between the vehicle and track with the train speed as parameters.

How could discharge management affect Florida spring fish assemblage structure?

PubMed

Work, Kirsten; Codner, Keneil; Gibbs, Melissa

2017-08-01

Freshwater bodies are increasingly affected by reductions in water quantity and quality and by invasions of exotic species. To protect water quantity and maintain the ecological integrity of many water bodies in central Florida, a program of adopting Minimum Flows and Levels (MFLs) has begun for both lentic and lotic waters. The purpose of this study was to determine whether there were relationships between discharge and stage, water quality, and biological parameters for Volusia Blue Spring, a first magnitude spring (discharge > 380,000 m 3 day -1 or 100 mgd) for which an MFL program was adopted in 2006. Over the course of fourteen years, we assessed fish density and diversity weekly, monthly, or seasonally with seine and snorkel counts. We evaluated annual changes in the assemblages for relationships with water quantity and quality. Low discharge and dissolved oxygen combined with high stage and conductivity produced a fish population with a lower density and diversity in 2014 than in previous years. Densities of fish taxonomic/functional groups also were low in 2014 and measures of water quantity were significant predictors of fish assemblage structure. As a result of the strong relationships between variation in discharge and an array of chemical and biological characteristics of the spring, we conclude that maintaining the historical discharge rate is important for preserving the ecological integrity of Volusia Blue Spring. Copyright © 2017 Elsevier Ltd. All rights reserved.

Seasonal variation of metabolism in lizard Phrynocephalus vlangalii at high altitude.

PubMed

Liang, Shiwei; Li, Weixin; Zhang, Yang; Tang, Xiaolong; He, Jianzheng; Bai, Yucheng; Li, Dongqin; Wang, Yan; Chen, Qiang

2017-01-01

Seasonal acclimatization is important for animals to live optimally in the varying environment. Phrynocephalus vlangalii, a species of lizard endemic in China, distributes on Qinghai-Tibet Plateau ranging from 2000 to 4600m above sea level. To dissect how this lizard mediate metabolism to adapt various season, the preferred body temperature (Tb), standard metabolic rate (SMR), mitochondrial respiration rates and activities of four metabolic enzymes in this species were tested in different seasons (spring, summer, and autumn). The results showed that the preferred Tb was the lowest in spring and the highest in summer. SMR, maximal mitochondrial respiration rates in liver and skeletal muscle were the highest in spring. Similarly, higher activities of lactate dehydrogenase (LDH), citrate synthase (CS) and cytochrome c oxidase (CCO) activities of liver and skeletal muscle were observed in spring. However, β-hydroxyacyl coenzyme A dehydrogenase (HOAD) activities of liver and skeletal muscle were higher in autumn. On the whole, seasonal variation of metabolism is the highest in spring and the lowest in summer. Seasonal variation of metabolism is the opposite of preferred body temperature, this may be one of the mechanisms to adapt to the environment in P. vlangalii. Our results suggested that P. vlangalii at high altitude has certain adaptive characteristics on metabolism in different seasons. Copyright © 2016 Elsevier Inc. All rights reserved.

Longer wings for faster springs - wing length relates to spring phenology in a long-distance migrant across its range.

PubMed

Hahn, Steffen; Korner-Nievergelt, Fränzi; Emmenegger, Tamara; Amrhein, Valentin; Csörgő, Tibor; Gursoy, Arzu; Ilieva, Mihaela; Kverek, Pavel; Pérez-Tris, Javier; Pirrello, Simone; Zehtindjiev, Pavel; Salewski, Volker

2016-01-01

In migratory birds, morphological adaptations for efficient migratory flight often oppose morphological adaptations for efficient behavior during resident periods. This includes adaptations in wing shape for either flying long distances or foraging in the vegetation and in climate-driven variation of body size. In addition, the timing of migratory flights and particularly the timely arrival at local breeding sites is crucial because fitness prospects depend on site-specific phenology. Thus, adaptations for efficient long-distance flights might be also related to conditions at destination areas. For an obligatory long-distance migrant, the common nightingale, we verified that wing length as the aerodynamically important trait, but not structural body size increased from the western to the eastern parts of the species range. In contrast with expectation from aerodynamic theory, however, wing length did not increase with increasing migration distances. Instead, wing length was associated with the phenology at breeding destinations, namely the speed of local spring green-up. We argue that longer wings are beneficial for adjusting migration speed to local conditions for birds breeding in habitats with fast spring green-up and thus short optimal arrival periods. We suggest that the speed of spring green-up at breeding sites is a fundamental variable determining the timing of migration that fine tune phenotypes in migrants across their range.

Assessment of spring cranioplasty biomechanics in sagittal craniosynostosis patients.

PubMed

Borghi, Alessandro; Schievano, Silvia; Rodriguez Florez, Naiara; McNicholas, Roisin; Rodgers, Will; Ponniah, Allan; James, Greg; Hayward, Richard; Dunaway, David; Jeelani, N U Owase

2017-11-01

OBJECTIVE Scaphocephaly secondary to sagittal craniosynostosis has been treated in recent years with spring-assisted cranioplasty, an innovative approach that leverages the use of metallic spring distractors to reshape the patient skull. In this study, a population of patients who had undergone spring cranioplasty for the correction of scaphocephaly at the Great Ormond Street Hospital for Children was retrospectively analyzed to systematically assess spring biomechanical performance and kinematics in relation to spring model, patient age, and outcomes over time. METHODS Data from 60 patients (49 males, mean age at surgery 5.2 ± 0.9 months) who had received 2 springs for the treatment of isolated sagittal craniosynostosis were analyzed. The opening distance of the springs at the time of insertion and removal was retrieved from the surgical notes and, during the implantation period, from planar radiographs obtained at 1 day postoperatively and at the 3-week follow-up. The force exerted by the spring to the patient skull at each time point was derived after mechanical testing of each spring model-3 devices with the same geometry but different wire thicknesses. Changes in the cephalic index between preoperatively and the 3-week follow-up were recorded. RESULTS Stiffer springs were implanted in older patients (p < 0.05) to achieve the same opening on-table as in younger patients, but this entailed significantly different-higher-forces exerted on the skull when combinations of stiffer springs were used (p < 0.001). After initial force differences between spring models, however, the devices all plateaued. Indeed, regardless of patient age or spring model, after 10 days from insertion, all the devices were open. CONCLUSIONS Results in this study provide biomechanical insights into spring-assisted cranioplasty and could help to improve spring design and follow-up strategy in the future.

The effect of spring pads in the secondary suspension of railway vehicles on bogie yaw resistance

NASA Astrophysics Data System (ADS)

Michálek, Tomáš; Zelenka, Jaromír

2015-12-01

This paper deals with properties of bogie yaw resistance of an electric locomotive with secondary suspension consisting of flexi-coil springs supplemented with tilting spring pads. Transversal stiffness of a sample of a spring/pad assembly was measured on a dynamic test stand of the University of Pardubice (Czech Republic) and the results were applied into a multi-body model of the locomotive created in the simulation tool 'SJKV'. On the basis of the simulation results, a detailed analysis of the bogie yaw resistance was performed in order to explain the effect in dynamic behaviour of the locomotive when the moment against bogie rotation (and therefore the distribution of guiding forces on individual wheels, as well) is influenced with the vehicle speed in a certain curve. Results of this analysis show that the application of suspension elements with strongly directionally dependent transversal stiffness into the secondary suspension can just lead to a dependency of the bogie yaw resistance on cant deficiency, i.e. on the vehicle speed in curve. This fact has wide consequences on the vehicle dynamics (especially on the guiding behaviour of the vehicle in curves) and it also points out that the current method of evaluation of the bogie yaw resistance according to relevant standards, which is related with assessment of the quasistatic safety of a railway vehicle against derailment, is not objective enough.

A Profile of Non-Degree Students at Queensborough Community College, Spring 1982.

ERIC Educational Resources Information Center

Cohen, Edward G.

During the spring semester, 1982, a study was conducted at Queensborough Community College (QCC) to determine the characteristics, course preferences, and academic performance of non-degree students, that is, the 18% (N=2,133) of the total student body (N=11,800) without a declared curriculum. The study showed that the mean age of the non-degree…

Quantifying Parkinson's disease progression by simulating gait patterns

NASA Astrophysics Data System (ADS)

Cárdenas, Luisa; Martínez, Fabio; Atehortúa, Angélica; Romero, Eduardo

2015-12-01

Modern rehabilitation protocols of most neurodegenerative diseases, in particular the Parkinson Disease, rely on a clinical analysis of gait patterns. Currently, such analysis is highly dependent on both the examiner expertise and the type of evaluation. Development of evaluation methods with objective measures is then crucial. Physical models arise as a powerful alternative to quantify movement patterns and to emulate the progression and performance of specific treatments. This work introduces a novel quantification of the Parkinson disease progression using a physical model that accurately represents the main gait biomarker, the body Center of Gravity (CoG). The model tracks the whole gait cycle by a coupled double inverted pendulum that emulates the leg swinging for the single support phase and by a damper-spring System (SDP) that recreates both legs in contact with the ground for the double phase. The patterns generated by the proposed model are compared with actual ones learned from 24 subjects in stages 2,3, and 4. The evaluation performed demonstrates a better performance of the proposed model when compared with a baseline model(SP) composed of a coupled double pendulum and a mass-spring system. The Frechet distance measured differences between model estimations and real trajectories, showing for stages 2, 3 and 4 distances of 0.137, 0.155, 0.38 for the baseline and 0.07, 0.09, 0.29 for the proposed method.

Temperature mediated moose survival in Northeastern Minnesota

USGS Publications Warehouse

Lenarz, M.S.; Nelson, M.E.; Schrage, M.W.; Edwards, A.J.

2009-01-01

The earth is in the midst of a pronounced warming trend and temperatures in Minnesota, USA, as elsewhere, are projected to increase. Northern Minnesota represents the southern edge to the circumpolar distribution of moose (Alces alces), a species intolerant of heat. Moose increase their metabolic rate to regulate their core body temperature as temperatures rise. We hypothesized that moose survival rates would be a function of the frequency and magnitude that ambient temperatures exceeded the upper critical temperature of moose. We compared annual and seasonal moose survival in northeastern Minnesota between 2002 and 2008 with a temperature metric. We found that models based on January temperatures above the critical threshold were inversely correlated with subsequent survival and explained >78 of variability in spring, fall, and annual survival. Models based on late-spring temperatures also explained a high proportion of survival during the subsequent fall. A model based on warm-season temperatures was important in explaining survival during the subsequent winter. Our analyses suggest that temperatures may have a cumulative influence on survival. We expect that continuation or acceleration of current climate trends will result in decreased survival, a decrease in moose density, and ultimately, a retreat of moose northward from their current distribution.

Wind Induced Sediment Resuspension in a Microtidal Estuary

NASA Technical Reports Server (NTRS)

Booth, J. G.; Miller, R. L.; McKee, B. A.; Leathers, R. A.

1999-01-01

Bottom sediment resuspension frequency, duration and extent (% of bottom sediments affected) were characterized for the fifteen month period from September 1995 to January 1997 for the Barataria Basin, LA. An empirical model of sediment resuspension as a function of wind speed, direction, fetch and water depth was derived from wave theory. Water column turbidity was examined by processing remotely sensed radiance information from visible and near-IR AVHRR imagery. Based on model predictions, wind induced resuspension occurred during all seasons of this study. Seasonal characteristics for resuspension reveal that late fall, winter and early spring are the periods of most frequent and intense resuspension. Model predictions of the critical wind speed required to induce resuspension indicate that winds of 4 m/s (averaged over all wind directions resuspend approximately 50% of bottom sediments in the water bodies examined. Winds of this magnitude (4 m/s) occurred for 80% of the time during the late fall, winter and early spring and for approximately 30% of the time during the summer. More than 50% of the bottom sedimets are resuspended throughout the year, indicating the importance of resuspension as a process affecting sediment and biogeochemical fluxes in the Barataria Basin.

A new bead-spring model for simulation of semi-flexible macromolecules

NASA Astrophysics Data System (ADS)

Saadat, Amir; Khomami, Bamin

2016-11-01

A bead-spring model for semi-flexible macromolecules is developed to overcome the deficiencies of the current coarse-grained bead-spring models. Specifically, model improvements are achieved through incorporation of a bending potential. The new model is designed to accurately describe the correlation along the backbone of the chain, segmental length, and force-extension behavior of the macromolecule even at the limit of 1 Kuhn step per spring. The relaxation time of different Rouse modes is used to demonstrate the capabilities of the new model in predicting chain dynamics.

Age, state, environment, and season dependence of senescence in body mass.

PubMed

Kroeger, Svenja B; Blumstein, Daniel T; Armitage, Kenneth B; Reid, Jane M; Martin, Julien G A

2018-02-01

Senescence is a highly variable process that comprises both age-dependent and state-dependent components and can be greatly affected by environmental conditions. However, few studies have quantified the magnitude of age-dependent and state-dependent senescence in key life-history traits across individuals inhabiting different spatially structured and seasonal environments. We used longitudinal data from wild female yellow-bellied marmots ( Marmota flaviventer ), living in two adjacent environments that differ in elevation and associated phenology, to quantify how age and individual state, measured as "time to death," affect body mass senescence in different environments. Further, we quantified how patterns of senescence differed between two biologically distinct seasons, spring, and late summer. Body mass senescence had an age-dependent component, expressed as a decrease in mass in old age. Overall, estimated age-dependent senescence was greater in females living in the more favorable lower elevation environment, than in the harsher higher elevation environment, and greater in late summer than in spring. Body mass senescence also had a state-dependent component, captured by effects of time to death, but only in the more favorable lower elevation environment. In spring, body mass gradually decreased from 2 years before death, whereas in late summer, state-dependent effects were expressed as a terminal decrease in body mass in the last year of life. Contrary to expectations, we found that senescence was more likely to be observed under more favorable environmental conditions, rather than under harsher conditions. By further demonstrating that senescence patterns differ among seasons, our results imply that within-year temporal environmental variation must be considered alongside spatial environmental variation in order to characterize and understand the pattern and magnitude of senescence in wild populations.

Levels and patterns of objectively-measured physical activity volume and intensity distribution in UK adolescents: the ROOTS study

PubMed Central

2014-01-01

Background Few studies have quantified levels of habitual physical activity across the entire intensity range. We aimed to describe variability in total and intensity-specific physical activity levels in UK adolescents across gender, socio-demographic, temporal and body composition strata. Methods Physical activity energy expenditure and minutes per day (min/d) spent sedentary and in light, moderate, and vigorous intensity physical activity were assessed in 825 adolescents from the ROOTS study (43.5% boys; mean age 15.0 ± 0.30 years), by 4 days of individually calibrated combined heart rate and movement sensing. Measurement days were classified as weekday or weekend and according to the three school terms: summer (April-July), autumn (September-December), and spring (January-March). Gender and age were self-reported and area-level SES determined by postcode data. Body composition was measured by anthropometry and bio-electrical impedance. Variability in physical activity and sedentary time was analysed by linear multilevel modelling, and logistic multilevel regression was used to determine factors associated with physical inactivity (<60 min moderate-to-vigorous intensity physical activity/d). Results During awake hours (15.8 ± 0.9 hrs/d), adolescents primarily engaged in light intensity physical activity (517 min/d) and sedentary time (364 min/d). Boys were consistently more physically active and less sedentary than girls, but gender differences were smaller at weekends, as activity levels in boys dropped more markedly when transitioning from weekday to weekend. Boys were more sedentary on both weekend days compared to during the week, whereas girls were more sedentary on Sunday but less sedentary on Saturday. In both genders light intensity physical activity was lower in spring, while moderate physical activity was lower in autumn and spring terms, compared to the summer term; sedentary time was also higher in spring than summer term. Adolescents with higher fatness engaged in less vigorous intensity physical activity. Factors associated with increased odds of physical inactivity were female gender, both weekend days in boys, and specifically Sunday in girls. Conclusions Physical activity components vary by gender, temporal factors and body composition in UK adolescents. The available data indicate that in adolescence, girls should be the primary targets of interventions designed to increase physical activity levels. PMID:24564949

Levels and patterns of objectively-measured physical activity volume and intensity distribution in UK adolescents: the ROOTS study.

PubMed

Collings, Paul J; Wijndaele, Katrien; Corder, Kirsten; Westgate, Kate; Ridgway, Charlotte L; Dunn, Valerie; Goodyer, Ian; Ekelund, Ulf; Brage, Soren

2014-02-24

Few studies have quantified levels of habitual physical activity across the entire intensity range. We aimed to describe variability in total and intensity-specific physical activity levels in UK adolescents across gender, socio-demographic, temporal and body composition strata. Physical activity energy expenditure and minutes per day (min/d) spent sedentary and in light, moderate, and vigorous intensity physical activity were assessed in 825 adolescents from the ROOTS study (43.5% boys; mean age 15.0 ± 0.30 years), by 4 days of individually calibrated combined heart rate and movement sensing. Measurement days were classified as weekday or weekend and according to the three school terms: summer (April-July), autumn (September-December), and spring (January-March). Gender and age were self-reported and area-level SES determined by postcode data. Body composition was measured by anthropometry and bio-electrical impedance. Variability in physical activity and sedentary time was analysed by linear multilevel modelling, and logistic multilevel regression was used to determine factors associated with physical inactivity (<60 min moderate-to-vigorous intensity physical activity/d). During awake hours (15.8 ± 0.9 hrs/d), adolescents primarily engaged in light intensity physical activity (517 min/d) and sedentary time (364 min/d). Boys were consistently more physically active and less sedentary than girls, but gender differences were smaller at weekends, as activity levels in boys dropped more markedly when transitioning from weekday to weekend. Boys were more sedentary on both weekend days compared to during the week, whereas girls were more sedentary on Sunday but less sedentary on Saturday. In both genders light intensity physical activity was lower in spring, while moderate physical activity was lower in autumn and spring terms, compared to the summer term; sedentary time was also higher in spring than summer term. Adolescents with higher fatness engaged in less vigorous intensity physical activity. Factors associated with increased odds of physical inactivity were female gender, both weekend days in boys, and specifically Sunday in girls. Physical activity components vary by gender, temporal factors and body composition in UK adolescents. The available data indicate that in adolescence, girls should be the primary targets of interventions designed to increase physical activity levels.

Hydrologic and Agent-based Modelling of Hydro-refugia in East Africa, Insights into the Importance of Water Resources in Hominin Evolution and Dispersal

NASA Astrophysics Data System (ADS)

Ashley, G. M.; Cuthbert, M. O.; Gleeson, T. P.; Reynolds, S. R.; Bennett, M. R.; Newton, A. C.; McCormack, C. J.

2017-12-01

Hominin evolution and climate variability have often been linked because of the apparent coincidence of climate fluctuations and speciation or extinctions, although the cause and effect of climate on natural selection is not clear. Climate in the EARS (East African Rift System) where most hominin first occurrences are located experienced an overall drying over the last 7 myr. Superimposed on this trend, Milankovitch cycles generated wet-dry precession cycles ( 23 kyr) that changed both water and food resource availability. During dry periods, lakes became more alkaline and rivers ephemeral but, groundwater, buffered from surface climate effects, remained a potential resource during the driest of times. The possibility of widespread groundwater sources hydro-refugia, such as springs, wetlands and groundwater-fed perennial streams has received little attention with respect to the paleoenvironmental context of hominin evolution or dispersal. We demonstrate that hydrogeological modelling of the modern landscape in East Africa coupled with ABM (agent-based modelling) of hominin movement yields new insight into potential correlates of hominin survival and dispersal. Digitized hydrological mapping of present day rivers, lakes and springs along the EARS (2000 km) from northern Tanzania to Ethiopia provided the modelling framework. Present day conditions are considered analogous to past dry periods; wet period conditions are an expanded hydrologic network including all surface water bodies. Our focus was on perennial springs discharging at 1,000 m3/y (volume to sustain a small wetland). 450 such springs occur and were found to be significantly controlled by geology, not just climate. The ABM was designed to determine if it was possible for humans to walk between hydro-refugia in 3 days. Four climate scenarios were run on ABM: wet, wet-to-dry, dry and dry-to-wet. During dry periods our results suggest that groundwater availability would have been critical to supporting isolated networks of hydro-refugia when potable surface water was scarce. As the climate got wetter modeled cross-rift dispersal potentially occurred before movement along the rift. The presence of groundwater hydro-refugia may help explain how some patterns of taxonomic diversity in hominins may have developed.

The influence of ligament modelling strategies on the predictive capability of finite element models of the human knee joint.

PubMed

Naghibi Beidokhti, Hamid; Janssen, Dennis; van de Groes, Sebastiaan; Hazrati, Javad; Van den Boogaard, Ton; Verdonschot, Nico

2017-12-08

In finite element (FE) models knee ligaments can represented either by a group of one-dimensional springs, or by three-dimensional continuum elements based on segmentations. Continuum models closer approximate the anatomy, and facilitate ligament wrapping, while spring models are computationally less expensive. The mechanical properties of ligaments can be based on literature, or adjusted specifically for the subject. In the current study we investigated the effect of ligament modelling strategy on the predictive capability of FE models of the human knee joint. The effect of literature-based versus specimen-specific optimized material parameters was evaluated. Experiments were performed on three human cadaver knees, which were modelled in FE models with ligaments represented either using springs, or using continuum representations. In spring representation collateral ligaments were each modelled with three and cruciate ligaments with two single-element bundles. Stiffness parameters and pre-strains were optimized based on laxity tests for both approaches. Validation experiments were conducted to evaluate the outcomes of the FE models. Models (both spring and continuum) with subject-specific properties improved the predicted kinematics and contact outcome parameters. Models incorporating literature-based parameters, and particularly the spring models (with the representations implemented in this study), led to relatively high errors in kinematics and contact pressures. Using a continuum modelling approach resulted in more accurate contact outcome variables than the spring representation with two (cruciate ligaments) and three (collateral ligaments) single-element-bundle representations. However, when the prediction of joint kinematics is of main interest, spring ligament models provide a faster option with acceptable outcome. Copyright © 2017 Elsevier Ltd. All rights reserved.

Vibration characteristics and optimization for panel elastically supported in mobile phone

NASA Astrophysics Data System (ADS)

Kaito, Y.; Honda, S.; Narita, Y.

2016-09-01

In recent years, usage of smartphones and tablet terminals have spread around the world. These devices using touchscreen as a user interface are currently mainstream. Also, in order to let information of input or output surely know to users, there are some types of equipment having vibrational function in touchscreen. Here, the material of touchscreen consists of glass and the glass panel is fixed to a mobile phone's body by adhesive tapes along the edge of the panel. However, due to the difficulty of design of vibration, it needs investigation with a vast number of manufacturing prototypes. Moreover, the vibration characteristic of panels is not enough regarding intensity and a tactile impression. Therefore, in this study, the authors consider the vibration characteristic of glass panel elastically fixed by adhesive tapes along edges. First, they show modeling of adhesive tapes along edges of panel by using translational and rotational springs. Second, they show formulating vibration characteristic by using an energy method. Third, they optimize spring constants of translational and rotational springs by using Genetic Algorithm(GA) from the obtained expression. Finally, they consider natural frequencies and eigenmodes which were acquired from experiments and simulations.

NiTi Alloy Negator Springs for Long-Stroke Constant-Force Shape Memory Actuators: Modeling, Simulation and Testing

NASA Astrophysics Data System (ADS)

Spaggiari, Andrea; Dragoni, Eugenio; Tuissi, Ausonio

2014-07-01

This work aims at the experimental characterization and modeling validation of shape memory alloy (SMA) Negator springs. According to the classic engineering books on springs, a Negator spring is a spiral spring made of strip of metal wound on the flat with an inherent curvature such that, in repose, each coil wraps tightly on its inner neighbor. The main feature of a Negator springs is the nearly constant force displacement behavior in the unwinding of the strip. Moreover the stroke is very long, theoretically infinite, as it depends only on the length of the initial strip. A Negator spring made in SMA is built and experimentally tested to demonstrate the feasibility of this actuator. The shape memory Negator spring behavior can be modeled with an analytical procedure, which is in good agreement with the experimental test and can be used for design purposes. In both cases, the material is modeled as elastic in austenitic range, while an exponential continuum law is used to describe the martensitic behavior. The experimental results confirms the applicability of this kind of geometry to the shape memory alloy actuators, and the analytical model is confirmed to be a powerful design tool to dimension and predict the spring behavior both in martensitic and austenitic range.

Method and apparatus for sensing the natural frequency of a cantilevered body

DOEpatents

Duncan, Michael G.

2000-01-01

A method and apparatus for measuring the natural resonant frequency of a spring element by monitoring a phase difference between an output signal from the spring element and an input signal to the spring element and by adjusting frequency of the input signal until a detected phase difference signals that the natural resonant frequency has been reached. The method and apparatus are applied to a micro-cantilevered elements used to measure gas compositions and concentrations. Such elements are provided with coatings that absorb gas to cause deflections and changes in the mass or spring constant of the cantilevered element. These changes correspond to changes in the natural resonant frequency of the cantilevered element which are measured using the method and apparatus described herein.

Failure analysis of energy storage spring in automobile composite brake chamber

NASA Astrophysics Data System (ADS)

Luo, Zai; Wei, Qing; Hu, Xiaofeng

2015-02-01

This paper set energy storage spring of parking brake cavity, part of automobile composite brake chamber, as the research object. And constructed the fault tree model of energy storage spring which caused parking brake failure based on the fault tree analysis method. Next, the parking brake failure model of energy storage spring was established by analyzing the working principle of composite brake chamber. Finally, the data of working load and the push rod stroke measured by comprehensive test-bed valve was used to validate the failure model above. The experimental result shows that the failure model can distinguish whether the energy storage spring is faulted.

Body composition and weight dynamics of wintering greater white-fronted geese

USGS Publications Warehouse

Ely, Craig R.; Raveling, Dennis G.

1989-01-01

Adult greater white-fronted geese (Anser albifrons frontalis) wintering in southern Oregon and California increased or maintained body weight in autumn, lost weight from autumn through winter, and rapidly increased in weight before spring migration in late April. We documented significant annual differences in body weights for both sexes. We related seasonal changes in body weight to changes in lipid levels, which were lowest (12-13% of wet wt in M and F) in mid-March and highest in late April (24% in F). Greater white-fronted geese maintained lipid levels during winter similar to those reported for large subspecies of Canada geese (Branta canadensis), and greater than those reported for small subspecies of Canada geese and other small species of geese. Protein content of carcasses varied significantly in females; i.e., lowest in early October and highest in late October and late April. Differences among species in patterns of weight change and body composition during winter seem to be related to social organization, body size, food type, and foraging behavior. Females left spring staging areas weighing relatively less than most other species of geese and may have benefited from foraging opportunities on the nesting grounds.

Muscle-spring dynamics in time-limited, elastic movements.

PubMed

Rosario, M V; Sutton, G P; Patek, S N; Sawicki, G S

2016-09-14

Muscle contractions that load in-series springs with slow speed over a long duration do maximal work and store the most elastic energy. However, time constraints, such as those experienced during escape and predation behaviours, may prevent animals from achieving maximal force capacity from their muscles during spring-loading. Here, we ask whether animals that have limited time for elastic energy storage operate with springs that are tuned to submaximal force production. To answer this question, we used a dynamic model of a muscle-spring system undergoing a fixed-end contraction, with parameters from a time-limited spring-loader (bullfrog: Lithobates catesbeiana) and a non-time-limited spring-loader (grasshopper: Schistocerca gregaria). We found that when muscles have less time to contract, stored elastic energy is maximized with lower spring stiffness (quantified as spring constant). The spring stiffness measured in bullfrog tendons permitted less elastic energy storage than was predicted by a modelled, maximal muscle contraction. However, when muscle contractions were modelled using biologically relevant loading times for bullfrog jumps (50 ms), tendon stiffness actually maximized elastic energy storage. In contrast, grasshoppers, which are not time limited, exhibited spring stiffness that maximized elastic energy storage when modelled with a maximal muscle contraction. These findings demonstrate the significance of evolutionary variation in tendon and apodeme properties to realistic jumping contexts as well as the importance of considering the effect of muscle dynamics and behavioural constraints on energy storage in muscle-spring systems. © 2016 The Author(s).

Models of Formation and Activity of Spring Mounds in the Mechertate-Chrita-Sidi El Hani System, Eastern Tunisia: Implications for the Habitability of Mars

PubMed Central

Essefi, Elhoucine; Komatsu, Goro; Fairén, Alberto G.; Chan, Marjorie A.; Yaich, Chokri

2014-01-01

Spring mounds on Earth and on Mars could represent optimal niches of life development. If life ever occurred on Mars, ancient spring deposits would be excellent localities to search for morphological or chemical remnants of an ancient biosphere. In this work, we investigate models of formation and activity of well-exposed spring mounds in the Mechertate-Chrita-Sidi El Hani (MCSH) system, eastern Tunisia. We then use these models to explore possible spring mound formation on Mars. In the MCSH system, the genesis of the spring mounds is a direct consequence of groundwater upwelling, triggered by tectonics and/or hydraulics. As they are oriented preferentially along faults, they can be considered as fault spring mounds, implying a tectonic influence in their formation process. However, the hydraulic pressure generated by the convergence of aquifers towards the surface of the system also allows consideration of an origin as artesian spring mounds. In the case of the MCSH system, our geologic data presented here show that both models are valid, and we propose a combined hydro-tectonic model as the likely formation mechanism of artesian-fault spring mounds. During their evolution from the embryonic (early) to the islet (“island”) stages, spring mounds are also shaped by eolian accumulations and induration processes. Similarly, spring mounds have been suggested to be relatively common in certain provinces on the Martian surface, but their mode of formation is still a matter of debate. We propose that the tectonic, hydraulic, and combined hydro-tectonic models describing the spring mounds at MCSH could be relevant as Martian analogs because: (i) the Martian subsurface may be over pressured, potentially expelling mineral-enriched waters as spring mounds on the surface; (ii) the Martian subsurface may be fractured, causing alignment of the spring mounds in preferential orientations; and (iii) indurated eolian sedimentation and erosional remnants are common features on Mars. The spring mounds further bear diagnostic mineralogic and magnetic properties, in comparison with their immediate surroundings. Consequently, remote sensing techniques can be very useful to identify similar spring mounds on Mars. The mechanisms (tectonic and/or hydraulic) of formation and evolution of spring mounds at the MCSH system are suitable for the proliferation and protection of life respectively. Similarly, life or its resulting biomarkers on Mars may have been protected or preserved under the spring mounds. PMID:25370379

Models of formation and activity of spring mounds in the mechertate-chrita-sidi el hani system, eastern Tunisia: implications for the habitability of Mars.

PubMed

Essefi, Elhoucine; Komatsu, Goro; Fairén, Alberto G; Chan, Marjorie A; Yaich, Chokri

2014-08-28

Spring mounds on Earth and on Mars could represent optimal niches of life development. If life ever occurred on Mars, ancient spring deposits would be excellent localities to search for morphological or chemical remnants of an ancient biosphere. In this work, we investigate models of formation and activity of well-exposed spring mounds in the Mechertate-Chrita-Sidi El Hani (MCSH) system, eastern Tunisia. We then use these models to explore possible spring mound formation on Mars. In the MCSH system, the genesis of the spring mounds is a direct consequence of groundwater upwelling, triggered by tectonics and/or hydraulics. As they are oriented preferentially along faults, they can be considered as fault spring mounds, implying a tectonic influence in their formation process. However, the hydraulic pressure generated by the convergence of aquifers towards the surface of the system also allows consideration of an origin as artesian spring mounds. In the case of the MCSH system, our geologic data presented here show that both models are valid, and we propose a combined hydro-tectonic model as the likely formation mechanism of artesian-fault spring mounds. During their evolution from the embryonic (early) to the islet ("island") stages, spring mounds are also shaped by eolian accumulations and induration processes. Similarly, spring mounds have been suggested to be relatively common in certain provinces on the Martian surface, but their mode of formation is still a matter of debate. We propose that the tectonic, hydraulic, and combined hydro-tectonic models describing the spring mounds at MCSH could be relevant as Martian analogs because: (i) the Martian subsurface may be over pressured, potentially expelling mineral-enriched waters as spring mounds on the surface; (ii) the Martian subsurface may be fractured, causing alignment of the spring mounds in preferential orientations; and (iii) indurated eolian sedimentation and erosional remnants are common features on Mars. The spring mounds further bear diagnostic mineralogic and magnetic properties, in comparison with their immediate surroundings. Consequently, remote sensing techniques can be very useful to identify similar spring mounds on Mars. The mechanisms (tectonic and/or hydraulic) of formation and evolution of spring mounds at the MCSH system are suitable for the proliferation and protection of life respectively. Similarly, life or its resulting biomarkers on Mars may have been protected or preserved under the spring mounds.

An Approach of Estimating Individual Growth Curves for Young Thoroughbred Horses Based on Their Birthdays

PubMed Central

ONODA, Tomoaki; YAMAMOTO, Ryuta; SAWAMURA, Kyohei; MURASE, Harutaka; NAMBO, Yasuo; INOUE, Yoshinobu; MATSUI, Akira; MIYAKE, Takeshi; HIRAI, Nobuhiro

2014-01-01

ABSTRACT We propose an approach of estimating individual growth curves based on the birthday information of Japanese Thoroughbred horses, with considerations of the seasonal compensatory growth that is a typical characteristic of seasonal breeding animals. The compensatory growth patterns appear during only the winter and spring seasons in the life of growing horses, and the meeting point between winter and spring depends on the birthday of each horse. We previously developed new growth curve equations for Japanese Thoroughbreds adjusting for compensatory growth. Based on the equations, a parameter denoting the birthday information was added for the modeling of the individual growth curves for each horse by shifting the meeting points in the compensatory growth periods. A total of 5,594 and 5,680 body weight and age measurements of Thoroughbred colts and fillies, respectively, and 3,770 withers height and age measurements of both sexes were used in the analyses. The results of predicted error difference and Akaike Information Criterion showed that the individual growth curves using birthday information better fit to the body weight and withers height data than not using them. The individual growth curve for each horse would be a useful tool for the feeding managements of young Japanese Thoroughbreds in compensatory growth periods. PMID:25013356

A new model for simulating spring discharge recession and estimating effective porosity of karst aquifers

NASA Astrophysics Data System (ADS)

Xu, Bin; Ye, Ming; Dong, Shuning; Dai, Zhenxue; Pei, Yongzhen

2018-07-01

Quantitative analysis of recession curves of karst spring hydrographs is a vital tool for understanding karst hydrology and inferring hydraulic properties of karst aquifers. This paper presents a new model for simulating karst spring recession curves. The new model has the following characteristics: (1) the model considers two separate but hydraulically connected reservoirs: matrix reservoir and conduit reservoir; (2) the model separates karst spring hydrograph recession into three stages: conduit-drainage stage, mixed-drainage stage (with both conduit drainage and matrix drainage), and matrix-drainage stage; and (3) in the mixed-drainage stage, the model uses multiple conduit layers to present different levels of conduit development. The new model outperforms the classical Mangin model and the recently developed Fiorillo model for simulating observed discharge at the Madison Blue Spring located in northern Florida. This is attributed to the latter two characteristics of the new model. Based on the new model, a method is developed for estimating effective porosity of the matrix and conduit reservoirs for the three drainage stages. The estimated porosity values are consistent with measured matrix porosity at the study site and with estimated conduit porosity reported in literature. The new model for simulating karst spring hydrograph recession is mathematically general, and can be applied to a wide range of karst spring hydrographs to understand groundwater flow in karst aquifers. The limitations of the model are discussed at the end of this paper.

The effect of linear spring number at side load of McPherson suspension in electric city car

NASA Astrophysics Data System (ADS)

Budi, Sigit Setijo; Suprihadi, Agus; Makhrojan, Agus; Ismail, Rifky; Jamari, J.

2017-01-01

The function of the spring suspension on Mc Pherson type is to control vehicle stability and increase ride convenience although having tendencies of side load presence. The purpose of this study is to obtain simulation results of Mc Pherson suspension spring in the electric city car by using the finite element method and determining the side load that appears on the spring suspension. This research is conducted in several stages; they are linear spring designing models with various spring coil and spring suspension modeling using FEM software. Suspension spring is compressed in the vertical direction (z-axis) and at the upper part of the suspension springs will be seen the force that arises towards the x, y, and z-axis to simulate the side load arising on the upper part of the spring. The results of FEM simulation that the side load on the spring toward the x and y-axis which the value gets close to zero is the most stable spring.

GIS-based groundwater potential mapping using boosted regression tree, classification and regression tree, and random forest machine learning models in Iran.

PubMed

Naghibi, Seyed Amir; Pourghasemi, Hamid Reza; Dixon, Barnali

2016-01-01

Groundwater is considered one of the most valuable fresh water resources. The main objective of this study was to produce groundwater spring potential maps in the Koohrang Watershed, Chaharmahal-e-Bakhtiari Province, Iran, using three machine learning models: boosted regression tree (BRT), classification and regression tree (CART), and random forest (RF). Thirteen hydrological-geological-physiographical (HGP) factors that influence locations of springs were considered in this research. These factors include slope degree, slope aspect, altitude, topographic wetness index (TWI), slope length (LS), plan curvature, profile curvature, distance to rivers, distance to faults, lithology, land use, drainage density, and fault density. Subsequently, groundwater spring potential was modeled and mapped using CART, RF, and BRT algorithms. The predicted results from the three models were validated using the receiver operating characteristics curve (ROC). From 864 springs identified, 605 (≈70 %) locations were used for the spring potential mapping, while the remaining 259 (≈30 %) springs were used for the model validation. The area under the curve (AUC) for the BRT model was calculated as 0.8103 and for CART and RF the AUC were 0.7870 and 0.7119, respectively. Therefore, it was concluded that the BRT model produced the best prediction results while predicting locations of springs followed by CART and RF models, respectively. Geospatially integrated BRT, CART, and RF methods proved to be useful in generating the spring potential map (SPM) with reasonable accuracy.

Do summer temperatures trigger spring maturation in pacific lamprey, Entosphenus tridentatus?

USGS Publications Warehouse

Clemens, B.J.; Van De Wetering, S.; Kaufman, J.; Holt, R.A.; Schreck, C.B.

2009-01-01

Pacific lamprey, Entosphenus tridentatus, return to streams and use somatic energy to fuel maturation. Body size decreases, the lamprey mature, spawn, and then die. We predicted that warm, summer temperatures (>20 ??C) would accentuate shrinkage in body size, and expedite sexual maturation and subsequent death. We compared fish reared in the laboratory at diel fluctuating temperatures of 20-24 ??C (mean = 21.8 ??C) with fish reared at cooler temperatures (13.6 ??C). The results confirmed our predictions. Lamprey from the warm water group showed significantly greater proportional decreases in body weight following the summer temperature treatments than fish from the cool water group. A greater proportion of warm water fish sexually matured (100%) and died (97%) the following spring than cool water fish (53% sexually mature, 61% died). Females tended to mature and die earlier than males, most obviously in the warm water group. ?? 2009 John Wiley & Sons A/S.

Walking on a moving surface: energy-optimal walking motions on a shaky bridge and a shaking treadmill can reduce energy costs below normal.

PubMed

Joshi, Varun; Srinivasan, Manoj

2015-02-08

Understanding how humans walk on a surface that can move might provide insights into, for instance, whether walking humans prioritize energy use or stability. Here, motivated by the famous human-driven oscillations observed in the London Millennium Bridge, we introduce a minimal mathematical model of a biped, walking on a platform (bridge or treadmill) capable of lateral movement. This biped model consists of a point-mass upper body with legs that can exert force and perform mechanical work on the upper body. Using numerical optimization, we obtain energy-optimal walking motions for this biped, deriving the periodic body and platform motions that minimize a simple metabolic energy cost. When the platform has an externally imposed sinusoidal displacement of appropriate frequency and amplitude, we predict that body motion entrained to platform motion consumes less energy than walking on a fixed surface. When the platform has finite inertia, a mass- spring-damper with similar parameters to the Millennium Bridge, we show that the optimal biped walking motion sustains a large lateral platform oscillation when sufficiently many people walk on the bridge. Here, the biped model reduces walking metabolic cost by storing and recovering energy from the platform, demonstrating energy benefits for two features observed for walking on the Millennium Bridge: crowd synchrony and large lateral oscillations.

Walking on a moving surface: energy-optimal walking motions on a shaky bridge and a shaking treadmill can reduce energy costs below normal

PubMed Central

Joshi, Varun; Srinivasan, Manoj

2015-01-01

Understanding how humans walk on a surface that can move might provide insights into, for instance, whether walking humans prioritize energy use or stability. Here, motivated by the famous human-driven oscillations observed in the London Millennium Bridge, we introduce a minimal mathematical model of a biped, walking on a platform (bridge or treadmill) capable of lateral movement. This biped model consists of a point-mass upper body with legs that can exert force and perform mechanical work on the upper body. Using numerical optimization, we obtain energy-optimal walking motions for this biped, deriving the periodic body and platform motions that minimize a simple metabolic energy cost. When the platform has an externally imposed sinusoidal displacement of appropriate frequency and amplitude, we predict that body motion entrained to platform motion consumes less energy than walking on a fixed surface. When the platform has finite inertia, a mass- spring-damper with similar parameters to the Millennium Bridge, we show that the optimal biped walking motion sustains a large lateral platform oscillation when sufficiently many people walk on the bridge. Here, the biped model reduces walking metabolic cost by storing and recovering energy from the platform, demonstrating energy benefits for two features observed for walking on the Millennium Bridge: crowd synchrony and large lateral oscillations. PMID:25663810

Evaluation of the intake of radon through skin from thermal water.

PubMed

Sakoda, Akihiro; Ishimori, Yuu; Tschiersch, Jochen

2016-07-01

The biokinetics of radon in the body has previously been studied with the assumption that its absorption through the skin is negligibly small. This assumption would be acceptable except in specific situations, such as bathing in a radon hot spring where the radon concentration in thermal water is far higher than that in air. The present study focused on such a situation in order to better understand the biokinetics of radon. To mathematically express the entry of radon through the skin into the body, we first modified the latest sophisticated biokinetic model for noble gases. Values of an important parameter for the model-the skin permeability coefficient K (m s(-1))-were derived using data from previous human studies. The analysis of such empirical data, which corresponded to radon concentrations in the air exhaled by subjects during and following bathing in radon-rich thermal water, revealed that the estimated K values had a log-normal distribution. The validity of the K values and the characteristics of the present model are then discussed. Furthermore, the impact of the intake of radon or its progeny via inhalation or skin absorption on radiation dose was also assessed for possible exposure scenarios in a radon hot spring. It was concluded that, depending on the radon concentration in thermal water, there might be situations in which the dose contribution resulting from skin absorption of radon is comparable to that resulting from inhalation of radon and its progeny. This conclusion can also apply to other therapeutic situations (e.g. staying in the pool for a longer period). © The Author 2016. Published by Oxford University Press on behalf of The Japan Radiation Research Society and Japanese Society for Radiation Oncology.

Statistical shape modelling to aid surgical planning: associations between surgical parameters and head shapes following spring-assisted cranioplasty.

PubMed

Rodriguez-Florez, Naiara; Bruse, Jan L; Borghi, Alessandro; Vercruysse, Herman; Ong, Juling; James, Greg; Pennec, Xavier; Dunaway, David J; Jeelani, N U Owase; Schievano, Silvia

2017-10-01

Spring-assisted cranioplasty is performed to correct the long and narrow head shape of children with sagittal synostosis. Such corrective surgery involves osteotomies and the placement of spring-like distractors, which gradually expand to widen the skull until removal about 4 months later. Due to its dynamic nature, associations between surgical parameters and post-operative 3D head shape features are difficult to comprehend. The current study aimed at applying population-based statistical shape modelling to gain insight into how the choice of surgical parameters such as craniotomy size and spring positioning affects post-surgical head shape. Twenty consecutive patients with sagittal synostosis who underwent spring-assisted cranioplasty at Great Ormond Street Hospital for Children (London, UK) were prospectively recruited. Using a nonparametric statistical modelling technique based on mathematical currents, a 3D head shape template was computed from surface head scans of sagittal patients after spring removal. Partial least squares (PLS) regression was employed to quantify and visualise trends of localised head shape changes associated with the surgical parameters recorded during spring insertion: anterior-posterior and lateral craniotomy dimensions, anterior spring position and distance between anterior and posterior springs. Bivariate correlations between surgical parameters and corresponding PLS shape vectors demonstrated that anterior-posterior (Pearson's [Formula: see text]) and lateral craniotomy dimensions (Spearman's [Formula: see text]), as well as the position of the anterior spring ([Formula: see text]) and the distance between both springs ([Formula: see text]) on average had significant effects on head shapes at the time of spring removal. Such effects were visualised on 3D models. Population-based analysis of 3D post-operative medical images via computational statistical modelling tools allowed for detection of novel associations between surgical parameters and head shape features achieved following spring-assisted cranioplasty. The techniques described here could be extended to other cranio-maxillofacial procedures in order to assess post-operative outcomes and ultimately facilitate surgical decision making.

Potential effects of groundwater pumping on water levels, phreatophytes, and spring discharges in Spring and Snake Valleys, White Pine County, Nevada, and adjacent areas in Nevada and Utah

USGS Publications Warehouse

Halford, Keith J.; Plume, Russell W.

2011-01-01

Assessing hydrologic effects of developing groundwater supplies in Snake Valley required numerical, groundwater-flow models to estimate the timing and magnitude of capture from streams, springs, wetlands, and phreatophytes. Estimating general water-table decline also required groundwater simulation. The hydraulic conductivity of basin fill and transmissivity of basement-rock distributions in Spring and Snake Valleys were refined by calibrating a steady state, three-dimensional, MODFLOW model of the carbonate-rock province to predevelopment conditions. Hydraulic properties and boundary conditions were defined primarily from the Regional Aquifer-System Analysis (RASA) model except in Spring and Snake Valleys. This locally refined model was referred to as the Great Basin National Park calibration (GBNP-C) model. Groundwater discharges from phreatophyte areas and springs in Spring and Snake Valleys were simulated as specified discharges in the GBNP-C model. These discharges equaled mapped rates and measured discharges, respectively. Recharge, hydraulic conductivity, and transmissivity were distributed throughout Spring and Snake Valleys with pilot points and interpolated to model cells with kriging in geologically similar areas. Transmissivity of the basement rocks was estimated because thickness is correlated poorly with transmissivity. Transmissivity estimates were constrained by aquifer-test results in basin-fill and carbonate-rock aquifers. Recharge, hydraulic conductivity, and transmissivity distributions of the GBNP-C model were estimated by minimizing a weighted composite, sum-of-squares objective function that included measurement and Tikhonov regularization observations. Tikhonov regularization observations were equations that defined preferred relations between the pilot points. Measured water levels, water levels that were simulated with RASA, depth-to-water beneath distributed groundwater and spring discharges, land-surface altitudes, spring discharge at Fish Springs, and changes in discharge on selected creek reaches were measurement observations. The effects of uncertain distributed groundwater-discharge estimates in Spring and Snake Valleys on transmissivity estimates were bounded with alternative models. Annual distributed groundwater discharges from Spring and Snake Valleys in the alternative models totaled 151,000 and 227,000 acre-feet, respectively and represented 20 percent differences from the 187,000 acre-feet per year that discharges from the GBNP-C model. Transmissivity estimates in the basin fill between Baker and Big Springs changed less than 50 percent between the two alternative models. Potential effects of pumping from Snake Valley were estimated with the Great Basin National Park predictive (GBNP-P) model, which is a transient groundwater-flow model. The hydraulic conductivity of basin fill and transmissivity of basement rock were the GBNP-C model distributions. Specific yields were defined from aquifer tests. Captures of distributed groundwater and spring discharges were simulated in the GBNP-P model using a combination of well and drain packages in MODFLOW. Simulated groundwater captures could not exceed measured groundwater-discharge rates. Four groundwater-development scenarios were investigated where total annual withdrawals ranged from 10,000 to 50,000 acre-feet during a 200-year pumping period. Four additional scenarios also were simulated that added the effects of existing pumping in Snake Valley. Potential groundwater pumping locations were limited to nine proposed points of diversion. Results are presented as maps of groundwater capture and drawdown, time series of drawdowns and discharges from selected wells, and time series of discharge reductions from selected springs and control volumes. Simulated drawdown propagation was attenuated where groundwater discharge could be captured. General patterns of groundwater capture and water-table declines were similar for all scenarios. Simulated drawdowns greater than 1 ft propagated outside of Spring and Snake Valleys after 200 years of pumping in all scenarios.

Effect of seasonal differences in dietary meat intake on changes in body mass and composition in wild and captive brown bears

USGS Publications Warehouse

Hilderbrand, Grant V.; Jenkins, S.G.; Schwartz, C.C.; Hanley, Thomas A.; Robbins, C.T.

1999-01-01

The influence of seasonal dietary meat intake on changes in body mass and composition in wild and captive brown bears (Ursus arctos) was investigated because the importance and availability of meat to brown bear populations is currently an important management consideration in several North American ecosystems. Adult female brown bears on the Kenai Peninsula, Alaska, utilized meat heavily in both spring and fall. Meat accounted for 76.2 ± 26.0% (mean ± 1 SD; primarily moose carrion and calves) of assimilated carbon and nitrogen in the spring and 80.4 ± 22.2% (primarily salmon) in the fall. Mass increases in the spring (71.8 ± 28.2%) were mostly lean body mass, but increases in the fall (81.0 ± 19.5%) were primarily fat. Daily intake by captive brown bears fed meat ad libitum during 12-day trials was positively related to body mass. Mass change was positively related to intake in both seasons, but the composition of the gain varied by season, with spring gains primarily lean body mass (64.2 ± 9.4%), while fall gains were 78.8 ± 19.6% lipid. Absolute rates of gain by wild bears occasionally equaled, but were usually much less than, those of captive bears. This was likely due to a combination of factors, which included the time required to locate and handle meat resources, the limited availability of or access to meat resources, and (or) the duration of meat resource availability. Estimated intake by bears not feeding selectively on high-energy components of moose and salmon were 8.5 ± 1.5 kg/day and 541 ± 156 kg/year and 10.8 ± 4.6 kg/day and 1003 ± 489 kg/year, respectively. Intake would drop by as much as 58% for bears feeding exclusively on salmon roe. Management strategies for areas with brown bears that consume significant amounts of meat should address the perpetuation and availability of these meat resources.

Maneuvers during legged locomotion

NASA Astrophysics Data System (ADS)

Jindrich, Devin L.; Qiao, Mu

2009-06-01

Maneuverability is essential for locomotion. For animals in the environment, maneuverability is directly related to survival. For humans, maneuvers such as turning are associated with increased risk for injury, either directly through tissue loading or indirectly through destabilization. Consequently, understanding the mechanics and motor control of maneuverability is a critical part of locomotion research. We briefly review the literature on maneuvering during locomotion with a focus on turning in bipeds. Walking turns can use one of several different strategies. Anticipation can be important to adjust kinematics and dynamics for smooth and stable maneuvers. During running, turns may be substantially constrained by the requirement for body orientation to match movement direction at the end of a turn. A simple mathematical model based on the requirement for rotation to match direction can describe leg forces used by bipeds (humans and ostriches). During running turns, both humans and ostriches control body rotation by generating fore-aft forces. However, whereas humans must generate large braking forces to prevent body over-rotation, ostriches do not. For ostriches, generating the lateral forces necessary to change movement direction results in appropriate body rotation. Although ostriches required smaller braking forces due in part to increased rotational inertia relative to body mass, other movement parameters also played a role. Turning performance resulted from the coordinated behavior of an integrated biomechanical system. Results from preliminary experiments on horizontal-plane stabilization support the hypothesis that controlling body rotation is an important aspect of stable maneuvers. In humans, body orientation relative to movement direction is rapidly stabilized during running turns within the minimum of two steps theoretically required to complete analogous maneuvers. During straight running and cutting turns, humans exhibit spring-mass behavior in the horizontal plane. Changes in the horizontal projection of leg length were linearly related to changes in horizontal-plane leg forces. Consequently, the passive dynamic stabilization associated with spring-mass behavior may contribute to stability during maneuvers in bipeds. Understanding the mechanics of maneuverability will be important for understanding the motor control of maneuvers and also potentially be useful for understanding stability.

Rubber friction and tire dynamics.

PubMed

Persson, B N J

2011-01-12

We propose a simple rubber friction law, which can be used, for example, in models of tire (and vehicle) dynamics. The friction law is tested by comparing numerical results to the full rubber friction theory (Persson 2006 J. Phys.: Condens. Matter 18 7789). Good agreement is found between the two theories. We describe a two-dimensional (2D) tire model which combines the rubber friction model with a simple mass-spring description of the tire body. The tire model is very flexible and can be used to accurately calculate μ-slip curves (and the self-aligning torque) for braking and cornering or combined motion (e.g. braking during cornering). We present numerical results which illustrate the theory. Simulations of anti-blocking system (ABS) braking are performed using two simple control algorithms.

Temporal shifts and temperature sensitivity of avian spring migratory phenology: a phylogenetic meta-analysis.

PubMed

Usui, Takuji; Butchart, Stuart H M; Phillimore, Albert B

2017-03-01

There are wide reports of advances in the timing of spring migration of birds over time and in relation to rising temperatures, though phenological responses vary substantially within and among species. An understanding of the ecological, life-history and geographic variables that predict this intra- and interspecific variation can guide our projections of how populations and species are likely to respond to future climate change. Here, we conduct phylogenetic meta-analyses addressing slope estimates of the timing of avian spring migration regressed on (i) year and (ii) temperature, representing a total of 413 species across five continents. We take into account slope estimation error and examine phylogenetic, ecological and geographic predictors of intra- and interspecific variation. We confirm earlier findings that on average birds have significantly advanced their spring migration time by 2·1 days per decade and 1·2 days °C -1 . We find that over time and in response to warmer spring conditions, short-distance migrants have advanced spring migratory phenology by more than long-distance migrants. We also find that larger bodied species show greater advance over time compared to smaller bodied species. Our results did not reveal any evidence that interspecific variation in migration response is predictable on the basis of species' habitat or diet. We detected a substantial phylogenetic signal in migration time in response to both year and temperature, suggesting that some of the shifts in migratory phenological response to climate are predictable on the basis of phylogeny. However, we estimate high levels of species and spatial variance relative to phylogenetic variance, which is consistent with plasticity in response to climate evolving fairly rapidly and being more influenced by adaptation to current local climate than by common descent. On average, avian spring migration times have advanced over time and as spring has become warmer. While we are able to identify predictors that explain some of the true among-species variation in response, substantial intra- and interspecific variation in migratory response remains to be explained. © 2016 The Authors. Journal of Animal Ecology published by John Wiley & Sons Ltd on behalf of British Ecological Society.

Feasibility and scalability of spring parameters in distraction enterogenesis in a murine model.

PubMed

Huynh, Nhan; Dubrovsky, Genia; Rouch, Joshua D; Scott, Andrew; Stelzner, Matthias; Shekherdimian, Shant; Dunn, James C Y

2017-07-01

Distraction enterogenesis has been investigated as a novel treatment for short bowel syndrome (SBS). With variable intestinal sizes, it is critical to determine safe, translatable spring characteristics in differently sized animal models before clinical use. Nitinol springs have been shown to lengthen intestines in rats and pigs. Here, we show spring-mediated intestinal lengthening is scalable and feasible in a murine model. A 10-mm nitinol spring was compressed to 3 mm and placed in a 5-mm intestinal segment isolated from continuity in mice. A noncompressed spring placed in a similar fashion served as a control. Spring parameters were proportionally extrapolated from previous spring parameters to accommodate the smaller size of murine intestines. After 2-3 wk, the intestinal segments were examined for size and histology. Experimental group with spring constants, k = 0.2-1.4 N/m, showed intestinal lengthening from 5.0 ± 0.6 mm to 9.5 ± 0.8 mm (P < 0.0001), whereas control segments lengthened from 5.3 ± 0.5 mm to 6.4 ± 1.0 mm (P < 0.02). Diameter increased similarly in both groups. Isolated segment perforation was noted when k ≥ 0.8 N/m. Histologically, lengthened segments had increased muscularis thickness and crypt depth in comparison to normal intestine. Nitinol springs with k ≤ 0.4 N/m can safely yield nearly 2-fold distraction enterogenesis in length and diameter in a scalable mouse model. Not only does this study derive the safe ranges and translatable spring characteristics in a scalable murine model for patients with short bowel syndrome, it also demonstrates the feasibility of spring-mediated intestinal lengthening in a mouse, which can be used to study underlying mechanisms in the future. Copyright © 2017 Elsevier Inc. All rights reserved.

On actuator placement for robust time-optimal control of uncertain flexible spacecraft

NASA Technical Reports Server (NTRS)

Wie, Bong; Sinha, Ravi; Liu, Qiang

1992-01-01

The problem of computing open-loop, on-off jet firing logic for flexible spacecraft in the face of plant modeling uncertainty is investigated. The primary control objective is to achieve a fast maneuvering time with a minimum of structural vibrations during and/or after a maneuver. This paper is also concerned with the problem of selecting a proper pair of jets for practical trade-offs among the maneuvering time, fuel consumption, structural mode excitation, and performance robustness. A time-optimal control problem subject to parameter robustness constraints is formulated. A three-mass-spring model of flexible spacecraft with a rigid-body mode and two flexible modes is used to illustrate the concept.

Entropy gives rise to topologically associating domains

PubMed Central

Vasquez, Paula A.; Hult, Caitlin; Adalsteinsson, David; Lawrimore, Josh; Forest, Mark G.; Bloom, Kerry

2016-01-01

We investigate chromosome organization within the nucleus using polymer models whose formulation is closely guided by experiments in live yeast cells. We employ bead-spring chromosome models together with loop formation within the chains and the presence of nuclear bodies to quantify the extent to which these mechanisms shape the topological landscape in the interphase nucleus. By investigating the genome as a dynamical system, we show that domains of high chromosomal interactions can arise solely from the polymeric nature of the chromosome arms due to entropic interactions and nuclear confinement. In this view, the role of bio-chemical related processes is to modulate and extend the duration of the interacting domains. PMID:27257057

Body condition explains migratory performance of a long-distance migrant.

PubMed

Duijns, Sjoerd; Niles, Lawrence J; Dey, Amanda; Aubry, Yves; Friis, Christian; Koch, Stephanie; Anderson, Alexandra M; Smith, Paul A

2017-11-15

Body condition (i.e. relative mass after correcting for structural size) affects the behaviour of migrating birds, but how body condition affects migratory performance, timing and fitness is still largely unknown. Here, we studied the effects of relative body condition on individual departure decisions, wind selectivity, flight speed and timing of migration for a long-distance migratory shorebird, the red knot Calidris canutus rufa. By using automated VHF telemetry on a continental scale, we studied knots' migratory movements with unprecedented temporal resolution over a 3-year period. Knots with a higher relative body condition left the staging site later than birds in lower condition, yet still arrived earlier to their Arctic breeding grounds compared to knots in lower relative body condition. They accomplished this by selecting more favourable winds at departure, thereby flying faster and making shorter stops en route Individuals with a higher relative body condition in spring migrated south up to a month later than individuals in lower condition, suggesting that individuals in better condition were more likely to have bred successfully. Moreover, individuals with a lower relative body condition in spring had a lower probability of being detected in autumn, suggestive of increased mortality. The pressure to arrive early to the breeding grounds is considered to be an important constraint of migratory behaviour and this study highlights the important influence of body condition on migratory decisions, performance and potentially fitness of migrant birds. © 2017 The Authors.

Evaluation of the intake of radon through skin from thermal water

PubMed Central

Sakoda, Akihiro; Ishimori, Yuu; Tschiersch, Jochen

2016-01-01

The biokinetics of radon in the body has previously been studied with the assumption that its absorption through the skin is negligibly small. This assumption would be acceptable except in specific situations, such as bathing in a radon hot spring where the radon concentration in thermal water is far higher than that in air. The present study focused on such a situation in order to better understand the biokinetics of radon. To mathematically express the entry of radon through the skin into the body, we first modified the latest sophisticated biokinetic model for noble gases. Values of an important parameter for the model—the skin permeability coefficient K (m s−1)—were derived using data from previous human studies. The analysis of such empirical data, which corresponded to radon concentrations in the air exhaled by subjects during and following bathing in radon-rich thermal water, revealed that the estimated K values had a log-normal distribution. The validity of the K values and the characteristics of the present model are then discussed. Furthermore, the impact of the intake of radon or its progeny via inhalation or skin absorption on radiation dose was also assessed for possible exposure scenarios in a radon hot spring. It was concluded that, depending on the radon concentration in thermal water, there might be situations in which the dose contribution resulting from skin absorption of radon is comparable to that resulting from inhalation of radon and its progeny. This conclusion can also apply to other therapeutic situations (e.g. staying in the pool for a longer period). PMID:26983980

Machine-Thermal Coupling Stresses Analysis of the Fin-Type Structural Thermoelectric Generator

NASA Astrophysics Data System (ADS)

Zhang, Zheng; Yue, Hao; Chen, Dongbo; Qin, Delei; Chen, Zijian

2017-05-01

The design structure and heat-transfer mechanism of a thermoelectric generator (TEG) determine its body temperature state. Thermal stress and thermal deformation generated by the temperature variation directly affect the stress state of thermoelectric modules (TEMs). Therefore, the rated temperature and pressing force of TEMs are important parameters in TEG design. Here, the relationships between structural of a fin-type TEG (FTEG) and these parameters are studied by modeling and "machine-thermal" coupling simulation. An indirect calculation method is adopted in the coupling simulation. First, numerical heat transfer calculations of a three-dimensional FTEG model are conducted according to an orthogonal simulation table. The influences of structural parameters for heat transfer in the channel and outer fin temperature distribution are analyzed. The optimal structural parameters are obtained and used to simulate temperature field of the outer fins. Second, taking the thermal calculation results as the initial condition, the thermal-solid coupling calculation is adopted. The thermal stresses of outer fin, mechanical force of spring-angle pressing mechanism, and clamping force on a TEM are analyzed. The simulation results show that the heat transfer area of the inner fin and the physical parameters of the metal materials are the keys to determining the FTEG temperature field. The pressing mechanism's mechanical force can be reduced by reducing the outer fin angle. In addition, a corrugated cooling water pipe, which has cooling and spring functionality, is conducive to establishing an adaptable clamping force to avoid the TEMs being crushed by the thermal stresses in the body.

Effect of temperature on the orthodontic clinical applications of niti closed-coil springs

PubMed Central

Espinar-Escalona, Eduardo; Llamas-Carreras, José M.; Barrera-Mora, José M.; Abalos-Lasbrucci, Camilo

2013-01-01

NiTi spring coils were used to obtain large deformation under a constant force. The device consists on a NiTi coil spring, superelastic at body temperature, in order to have a stress plateau during the austenitic retransformation during the unloading. The temperature variations induced changes in the spring force. Objectives: The aim of this study is to investigate the effect of the temperature variations in the spring forces and corrosion behaviour simulating the ingestion hot/cold drinks and food. Study Design: The springs were subjected to a tensile force using universal testing machine MTS-Adamel (100 N load cell). All tests were performed in artificial saliva maintained at different temperatures. The corrosion tests were performed according to the ISO-standard 10993-15:2000. Results: The increase in temperature of 18oC induced an increase in the spring force of 30%. However, when the temperature returns to 37oC the distraction force recovers near the initial level. After cooling down the spring to 15oC, the force decreased by 46%. This investigation show as the temperature increase, the corrosion potential shifts towards negative values and the corrosion density is rising. Conclusions: The changes of the temperatures do not modify the superelastic behaviour of the NiTi closed-coil springs. The corrosion potential of NiTi in artificial saliva is decreasing by the rise of the temperatures. Key words:Superelasticity, NiTi, springs, orthodontic, coils, recovery, temperature. PMID:23722142

The Freshman 15--A Closer Look

ERIC Educational Resources Information Center

Gropper, Sareen S.; Simmons, Karla P.; Gaines, Alisha; Drawdy, Kelly; Saunders, Desiree; Ulrich, Pamela; Connell, Lenda Jo

2009-01-01

Objectives and Participants: Changes in body weight, composition, and size were examined in college freshmen at the beginning (initial, n = 240) and end of fall semester 2007 (n = 214) and the end of spring semester 2008 (n = 205). Methods: Height, weight, body composition, and waist and hip measurements were assessed. Results: Mean weight, body…

Generalized Predictive Control of Dynamic Systems with Rigid-Body Modes

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.

2013-01-01

Numerical simulations to assess the effectiveness of Generalized Predictive Control (GPC) for active control of dynamic systems having rigid-body modes are presented. GPC is a linear, time-invariant, multi-input/multi-output predictive control method that uses an ARX model to characterize the system and to design the controller. Although the method can accommodate both embedded (implicit) and explicit feedforward paths for incorporation of disturbance effects, only the case of embedded feedforward in which the disturbances are assumed to be unknown is considered here. Results from numerical simulations using mathematical models of both a free-free three-degree-of-freedom mass-spring-dashpot system and the XV-15 tiltrotor research aircraft are presented. In regulation mode operation, which calls for zero system response in the presence of disturbances, the simulations showed reductions of nearly 100%. In tracking mode operations, where the system is commanded to follow a specified path, the GPC controllers produced the desired responses, even in the presence of disturbances.

A real-time posture monitoring method for rail vehicle bodies based on machine vision

NASA Astrophysics Data System (ADS)

Liu, Dongrun; Lu, Zhaijun; Cao, Tianpei; Li, Tian

2017-06-01

Monitoring vehicle operation conditions has become significantly important in modern high-speed railway systems. However, the operational impact of monitoring the roll angle of vehicle bodies has principally been limited to tilting trains, while few studies have focused on monitoring the running posture of vehicle bodies during operation. We propose a real-time posture monitoring method to fulfil real-time monitoring requirements, by taking rail surfaces and centrelines as detection references. In realising the proposed method, we built a mathematical computational model based on space coordinate transformations to calculate attitude angles of vehicles in operation and vertical and lateral vibration displacements of single measuring points. Moreover, comparison and verification of reliability between system and field results were conducted. Results show that monitoring of the roll angles of car bodies obtained through the system exhibit variation trends similar to those converted from the dynamic deflection of bogie secondary air springs. The monitoring results of two identical conditions were basically the same, highlighting repeatability and good monitoring accuracy. Therefore, our monitoring results were reliable in reflecting posture changes in running railway vehicles.

The effects of overwintering and habitat type on body condition and locomotion of the wolf spider Pardosa alacris

NASA Astrophysics Data System (ADS)

Ingle, Kapilkumar; Horváth, Ádám; Gallé-Szpisjak, Nikolett; Gellért, Levente; Csata, Enikő; Gallé, Róbert

2018-05-01

Overwintering in temperate regions is a prominent mortality risk for invertebrates and may affect their behaviour and body condition. Pardosa alacris is a common ground dwelling spider in central European native and plantation forests, and habitat type and prey availability may play important roles in their overwintering. The effect of overwintering on body condition and behaviour of spiders in semi natural and exotic habitats is relatively unknown. Here we assess the effects of winter on spiders from native poplar and exotic pine plantations. The locomotory behaviour of P. alacris (distance covered and speed) was assessed by tracking their movement in a white circular plastic arena. We assessed body condition, body size, and total fat content. Forest type and sex had significant effects on body length. Fat content was significantly higher in the spring than in autumn, and spiders covered larger distances and were faster in autumn than in spring. Fat content had a significant negative effect on average speed. Spiders in native forests were smaller but grew more during the winter than in exotic plantations, possibly due to higher prey availability in native forests. Visually-hunting predators may significantly affect spiders. Fat spiders with better body condition moved less, and were thus less detectable by predators. However the low movement rate may result in a low rate of encountering prey items, thus lowering feeding efficiency.

Modeling the effects of pumping wells in spring management: The case of Scirca spring (central Apennines, Italy)

NASA Astrophysics Data System (ADS)

Dragoni, W.; Mottola, A.; Cambi, C.

2013-06-01

One of the techniques used to increase the water yield of springs during dry seasons and droughts is drilling wells close to them. Where there is a low-hydraulic conductivity boundary close to a spring (the case considered here), this technique implies low well efficiency, high drawdown, and high cost of withdrawals. In addition, a set of pumping wells close to a spring can cause both it and the stream originating from it to dry up - a situation which is not always acceptable from an environmental point of view. In order to study better management strategies, this paper presents a finite difference model of the Scirca spring (Umbria - Marche Apennines, Italy), which originates from a limestone massif in which some formations are karstified. The model, built with Modflow using the equivalent porous media (EPM) approach, simulated the effects of pumping wells at various distances from the spring. Hydraulic Conductivity and Storativity were calibrated and validated on discharge data during recession, when recharge is nil. "Inverse modeling" was then used to estimate the daily recharge of the hydro-geological system of the Scirca spring for a period of several years. Lastly, the efficiency of various management schemes was evaluated by simulating the reaction of the spring, in terms of discharge, to a series of pumping scenarios, all guaranteeing a certain imposed withdrawal during summer, much larger than the natural spring discharge, given by spring discharge and well drawdown. The wells were located between 2850 and 100 m from the spring, the pumping time-span was set at 90 days, and pumping rates of 60, 90 and 120 l/s were applied. Results show that the maximum discharge at which spring drainage is avoided and that minimum vital flow is guaranteed is 90 l/s. The higher water volumes extracted during summer (dry season) are balanced by a lowering of the maximum natural discharges in winter and spring (recharge seasons). Simulations indicate that, by drilling pumping wells far from the spring, the efficiency of the whole system can be optimized in terms of total withdrawal, drilling and management costs, with reduced environmental impact. The mathematical model also shows how long the system takes to regain its "undisturbed" state, with a tolerance of 0.5 l/s. The model highlights the possibility of forcing the system to supply a smaller amount of water in winter, in order to increase the summer yield. Such a management scheme, which can be applied to other springs, may be useful in better meeting the demand for water during dry seasons.

Reply to Discussion by Zekai Șen on "Modeling karst spring hydrograph recession based on head drop at sinkholes"

NASA Astrophysics Data System (ADS)

Field, Malcolm S.; Goldscheider, Nico; Li, Guangquan

2018-02-01

We are pleased to learn that the model presented in our paper dealing with the "modeling karst spring hydrograph recession based on head drop at sinkholes," published in the Journal of Hydrology in 2016 (Li et al., 2016), is of interest to readers of this journal. Our study presented a new non-exponential model for assessing spring hydrographs in terms of head drop at flooded sinkholes, as an extension of an earlier model proposed by Li and Field (2014). In both papers, we used two spring hydrographs measured in the St. Marks Karst Watershed in northwest Florida to test the applicability and to verify the validity of our models.

Does winter region affect spring arrival time and body mass of king eiders in northern Alaska?

USGS Publications Warehouse

Oppel, Steffen; Powell, Abby N.

2009-01-01

Events during the non-breeding season may affect the body condition of migratory birds and influence performance during the following breeding season. Migratory birds nesting in the Arctic often rely on endogenous nutrients for reproductive efforts, and are thus potentially subject to such carry-over effects. We tested whether king eider (Somateria spectabilis) arrival time and body mass upon arrival at breeding grounds in northern Alaska were affected by their choice of a winter region in the Bering Sea. We captured birds shortly after arrival on breeding grounds in early June 2002–2006 at two sites in northern Alaska and determined the region in which individuals wintered using satellite telemetry or stable isotope ratios of head feathers. We used generalized linear models to assess whether winter region explained variation in arrival body mass among individuals by accounting for sex, site, annual variation, and the date a bird was captured. We found no support for our hypothesis that either arrival time or arrival body mass of king eiders differed among winter regions. We conclude that wintering in different regions in the Bering Sea is unlikely to have reproductive consequences for king eiders in our study areas.

A fast mass spring model solver for high-resolution elastic objects

NASA Astrophysics Data System (ADS)

Zheng, Mianlun; Yuan, Zhiyong; Zhu, Weixu; Zhang, Guian

2017-03-01

Real-time simulation of elastic objects is of great importance for computer graphics and virtual reality applications. The fast mass spring model solver can achieve visually realistic simulation in an efficient way. Unfortunately, this method suffers from resolution limitations and lack of mechanical realism for a surface geometry model, which greatly restricts its application. To tackle these problems, in this paper we propose a fast mass spring model solver for high-resolution elastic objects. First, we project the complex surface geometry model into a set of uniform grid cells as cages through *cages mean value coordinate method to reflect its internal structure and mechanics properties. Then, we replace the original Cholesky decomposition method in the fast mass spring model solver with a conjugate gradient method, which can make the fast mass spring model solver more efficient for detailed surface geometry models. Finally, we propose a graphics processing unit accelerated parallel algorithm for the conjugate gradient method. Experimental results show that our method can realize efficient deformation simulation of 3D elastic objects with visual reality and physical fidelity, which has a great potential for applications in computer animation.

Associations of intestinal helminth infections with health parameters of spring-migrating female lesser scaup (Aythya affinis) in the upper Midwest, USA.

PubMed

Conner England, J; Levengood, Jeffrey M; Osborn, Josh M; Yetter, Aaron P; Suski, Cory D; Cole, Rebecca A; Hagy, Heath M

2018-06-01

Thousands of lesser scaup (Aythya affinis) die during spring and fall migrations through the upper Midwest, USA, from infections with Cyathocotyle bushiensis and Sphaeridiotrema spp. (Class: Trematoda) after ingesting infected intermediate hosts, such as non-native faucet snails (Bithynia tentaculata). The lesser scaup is a species of conservation concern and is highly susceptible to these infections. We collected female lesser scaup from spring migratory stopover locations throughout Illinois and Wisconsin and assessed biochemical and morphological indicators of health in relation to intestinal helminth loads. Helminth species diversity, total trematode abundance, and the infection intensities of the trematodes C. bushiensis and Sphaeridiotrema spp. were associated with percent body fat, blood metabolites, hematological measures, and an index of foraging habitat quality. Helminth diversity was negatively associated with percent body fat, albumin concentrations, and monocytes, whereas glucose concentrations displayed a slight, positive association. Total trematode abundance was negatively associated with blood concentrations of non-esterified fatty acids and albumin. Infections of C. bushiensis were positively related to basophil levels, whereas Sphaeridiotrema spp. infection intensity was negatively associated with packed cell volume and foraging habitat quality. Thus, commonly measured health metrics may indicate intestinal parasite infections and help waterfowl managers understand overall habitat quality. Intestinal parasitic loads offer another plausible mechanism underlying the spring condition hypothesis.

Transient nature of Arctic spring systems driven by subglacial meltwater

NASA Astrophysics Data System (ADS)

Scheidegger, J. M.; Bense, V. F.; Grasby, S. E.

2012-06-01

In the High Arctic, supra- and proglacial springs occur at Borup Fiord Pass, Ellesmere Island. Spring waters are sulfur bearing and isotope analysis suggests springs are fed by deeply circulating glacial meltwater. However, the mechanism maintaining spring flow is unclear in these areas of thick permafrost which would hamper the discharge of deep groundwater to the surface. It has been hypothesized that fracture zones along faults focus groundwater which discharges initially underneath wet-based parts of the ice. With thinning ice, the spring head is exposed to surface temperatures, tens of degrees lower than temperatures of pressure melting, and permafrost starts to develop. Numerical modeling of coupled heat and fluid flow suggest that focused groundwater discharge should eventually be cut off by permafrost encroaching into the feeding channel of the spring. Nevertheless, our model simulations show that these springs can remain flowing for millennia depending on the initial flow rate and ambient surface temperature. These systems might provide a terrestrial analog for the possible occurrence of Martian springs recharged by polar ice caps.

Canadian crop calendars in support of the early warning project

NASA Technical Reports Server (NTRS)

Trenchard, M. H.; Hodges, T. (Principal Investigator)

1980-01-01

The Canadian crop calendars for LACIE are presented. Long term monthly averages of daily maximum and daily minimum temperatures for subregions of provinces were used to simulate normal daily maximum and minimum temperatures. The Robertson (1968) spring wheat and Williams (1974) spring barley phenology models were run using the simulated daily temperatures and daylengths for appropriate latitudes. Simulated daily temperatures and phenology model outputs for spring wheat and spring barley are given.

Finite element fatigue analysis of rectangular clutch spring of automatic slack adjuster

NASA Astrophysics Data System (ADS)

Xu, Chen-jie; Luo, Zai; Hu, Xiao-feng; Jiang, Wen-song

2015-02-01

The failure of rectangular clutch spring of automatic slack adjuster directly affects the work of automatic slack adjuster. We establish the structural mechanics model of automatic slack adjuster rectangular clutch spring based on its working principle and mechanical structure. In addition, we upload such structural mechanics model to ANSYS Workbench FEA system to predict the fatigue life of rectangular clutch spring. FEA results show that the fatigue life of rectangular clutch spring is 2.0403×105 cycle under the effect of braking loads. In the meantime, fatigue tests of 20 automatic slack adjusters are carried out on the fatigue test bench to verify the conclusion of the structural mechanics model. The experimental results show that the mean fatigue life of rectangular clutch spring is 1.9101×105, which meets the results based on the finite element analysis using ANSYS Workbench FEA system.

NASA USRP Internship Final Report

NASA Technical Reports Server (NTRS)

Black, Jesse A.

2010-01-01

The purpose of this report is to describe the body of work I have produced as a NASA USRP intern in the spring 2010. My mentor during this time was Richard Birr and I assisted him with many tasks in the advanced systems group in the engineering design lab at NASA's Kennedy space center. The main priority was and scenario modeling for the FAA's next generation air traffic control system and also developing next generation range systems for implementation at Kennedy space center. Also of importance was the development of wiring diagrams for the portable communications terminal for the desert rats program.

Continuation of periodic orbits in symmetric Hamiltonian and conservative systems

NASA Astrophysics Data System (ADS)

Galan-Vioque, J.; Almaraz, F. J. M.; Macías, E. F.

2014-12-01

We present and review results on the continuation and bifurcation of periodic solutions in conservative, reversible and Hamiltonian systems in the presence of symmetries. In particular we show how two-point boundary value problem continuation software can be used to compute families of periodic solutions of symmetric Hamiltonian systems. The technique is introduced with a very simple model example (the mathematical pendulum), justified with a theoretical continuation result and then applied to two non trivial examples: the non integrable spring pendulum and the continuation of the figure eight solution of the three body problem.

Navigating north: how body mass and winds shape avian flight behaviours across a North American migratory flyway.

PubMed

Horton, Kyle G; Van Doren, Benjamin M; La Sorte, Frank A; Fink, Daniel; Sheldon, Daniel; Farnsworth, Andrew; Kelly, Jeffrey F

2018-05-07

The migratory patterns of birds have been the focus of ecologists for millennia. What behavioural traits underlie these remarkably consistent movements? Addressing this question is central to advancing our understanding of migratory flight strategies and requires the integration of information across levels of biological organisation, e.g. species to communities. Here, we combine species-specific observations from the eBird citizen-science database with observations aggregated from weather surveillance radars during spring migration in central North America. Our results confirm a core prediction of migration theory at an unprecedented national scale: body mass predicts variation in flight strategies across latitudes, with larger-bodied species flying faster and compensating more for wind drift. We also find evidence that migrants travelling northward earlier in the spring increasingly compensate for wind drift at higher latitudes. This integration of information across biological scales provides new insight into patterns and determinants of broad-scale flight strategies of migratory birds. © 2018 John Wiley & Sons Ltd/CNRS.

Bacterial and archeal community composition in hot springs from Indo-Burma region, North-east India.

PubMed

Panda, Amrita Kumari; Bisht, Satpal Singh; De Mandal, Surajit; Kumar, Nachimuthu Senthil

2016-12-01

Bacterial and archaeal diversity of two alkaline Indian hot springs, Jakrem (Meghalaya) and Yumthang (Sikkim), were studied. Thirteen major bacterial phyla were identified of which Firmicutes, Chloroflexi and Thermi were dominant in Jakrem and Proteobacteria in Yumthang. The dominant genera were Clostridium, Chloroflexus and Meiothermus at Jakrem (water temperature 46 °C, pH 9) and Thiobacillus, Sulfuritalea at Yumthang (water temperature 39 °C, pH 8) hot springs. The four Euryarchaeota taxa that were observed in both the hot springs were Methanoculleus, Methanosaeta, Methanosarcina and Methanocorposculum. Elstera litoralis, Thiovirga sp., Turneriella sp. were observed for the first time in association with hot springs along with Tepidibacter sp., Ignavibacterium sp., Teribacillus sp. and Dechloromonas sp. Individual bacterial phyla were found to be specifically correlated with certain physico-chemical factors such as temperature, dissolved SiO 2 , elemental S, total sulphide, calcium concentrations in hot spring water. Bacterial reads involved in sulfur cycle were identified in both16S rRNA gene library and sulfur metabolism may play key physiological functions in this hot spring. Members within Desulfobacterales and Thermodesulfovibrionaceae were identified and hypothesized their role in regulating sulfur cycle. The presence of many taxonomically unsolved sequences in the 16S rRNA gene tag datasets from these hot springs could be a sign of novel microbe richness in these less known hot water bodies of Northeastern India.

Using a binary logistic regression method and GIS for evaluating and mapping the groundwater spring potential in the Sultan Mountains (Aksehir, Turkey)

NASA Astrophysics Data System (ADS)

Ozdemir, Adnan

2011-07-01

SummaryThe purpose of this study is to produce a groundwater spring potential map of the Sultan Mountains in central Turkey, based on a logistic regression method within a Geographic Information System (GIS) environment. Using field surveys, the locations of the springs (440 springs) were determined in the study area. In this study, 17 spring-related factors were used in the analysis: geology, relative permeability, land use/land cover, precipitation, elevation, slope, aspect, total curvature, plan curvature, profile curvature, wetness index, stream power index, sediment transport capacity index, distance to drainage, distance to fault, drainage density, and fault density map. The coefficients of the predictor variables were estimated using binary logistic regression analysis and were used to calculate the groundwater spring potential for the entire study area. The accuracy of the final spring potential map was evaluated based on the observed springs. The accuracy of the model was evaluated by calculating the relative operating characteristics. The area value of the relative operating characteristic curve model was found to be 0.82. These results indicate that the model is a good estimator of the spring potential in the study area. The spring potential map shows that the areas of very low, low, moderate and high groundwater spring potential classes are 105.586 km 2 (28.99%), 74.271 km 2 (19.906%), 101.203 km 2 (27.14%), and 90.05 km 2 (24.671%), respectively. The interpretations of the potential map showed that stream power index, relative permeability of lithologies, geology, elevation, aspect, wetness index, plan curvature, and drainage density play major roles in spring occurrence and distribution in the Sultan Mountains. The logistic regression approach has not yet been used to delineate groundwater potential zones. In this study, the logistic regression method was used to locate potential zones for groundwater springs in the Sultan Mountains. The evolved model was found to be in strong agreement with the available groundwater spring test data. Hence, this method can be used routinely in groundwater exploration under favourable conditions.

Comparison of CRD, APU, and state models for Iowa corn and soybeans and North Dakota barley and spring wheat

NASA Technical Reports Server (NTRS)

French, V.

1983-01-01

A comparison was made among the CEAS crop reporting district (CRD), agrophysical unit (APU), and state level multiple regression yield models for corn and soybeans in Iowa and barley and spring wheat in North Dakota. The best predictions were made by the state model for North Dakota spring wheat, by the APU models for barley, by the CRD models for Iowa soybeans, and by APU covariance models for Iowa corn. Because of this lack of consistency of model performance, CRD models would be recommended due to the availability of the data.

An oscillating wave energy converter with nonlinear snap-through Power-Take-Off systems in regular waves

NASA Astrophysics Data System (ADS)

Zhang, Xian-tao; Yang, Jian-min; Xiao, Long-fei

2016-07-01

Floating oscillating bodies constitute a large class of wave energy converters, especially for offshore deployment. Usually the Power-Take-Off (PTO) system is a directly linear electric generator or a hydraulic motor that drives an electric generator. The PTO system is simplified as a linear spring and a linear damper. However the conversion is less powerful with wave periods off resonance. Thus, a nonlinear snap-through mechanism with two symmetrically oblique springs and a linear damper is applied in the PTO system. The nonlinear snap-through mechanism is characteristics of negative stiffness and double-well potential. An important nonlinear parameter γ is defined as the ratio of half of the horizontal distance between the two springs to the original length of both springs. Time domain method is applied to the dynamics of wave energy converter in regular waves. And the state space model is used to replace the convolution terms in the time domain equation. The results show that the energy harvested by the nonlinear PTO system is larger than that by linear system for low frequency input. While the power captured by nonlinear converters is slightly smaller than that by linear converters for high frequency input. The wave amplitude, damping coefficient of PTO systems and the nonlinear parameter γ affect power capture performance of nonlinear converters. The oscillation of nonlinear wave energy converters may be local or periodically inter well for certain values of the incident wave frequency and the nonlinear parameter γ, which is different from linear converters characteristics of sinusoidal response in regular waves.

Reachability and Real-Time Actuation Strategies for the Active SLIP Model

DTIC Science & Technology

2015-06-01

spring leg, the Spring Loaded Inverted Pendulum (SLIP) is a prevalent model for analyzing running and hopping. In this work we consider an actuated...forced symmetry of the stance phase for the Spring-Loaded Inverted Pendulum , In Proceedings of the 2012 IEEE International Conference on Robotics and...Networks. Automatica, 49(1):206-213, 2013 (v) G. Piovan and K. Byl. Enforced symmetry of the stance phase for the spring-loaded inverted pendulum . In

Human hopping on damped surfaces: strategies for adjusting leg mechanics.

PubMed

Moritz, Chet T; Farley, Claire T

2003-08-22

Fast-moving legged animals bounce along the ground with spring-like legs and agilely traverse variable terrain. Previous research has shown that hopping and running humans maintain the same bouncing movement of the body's centre of mass on a range of elastic surfaces by adjusting their spring-like legs to exactly offset changes in surface stiffness. This study investigated human hopping on damped surfaces that dissipated up to 72% of the hopper's mechanical energy. On these surfaces, the legs did not act like pure springs. Leg muscles performed up to 24-fold more net work to replace the energy lost by the damped surface. However, considering the leg and surface together, the combination appeared to behave like a constant stiffness spring on all damped surfaces. By conserving the mechanics of the leg-surface combination regardless of surface damping, hoppers also conserved centre-of-mass motions. Thus, the normal bouncing movements of the centre of mass in hopping are not always a direct result of spring-like leg behaviour. Conserving the trajectory of the centre of mass by maintaining spring-like mechanics of the leg-surface combination may be an important control strategy for fast-legged locomotion on variable terrain.

Human hopping on damped surfaces: strategies for adjusting leg mechanics.

PubMed Central

Moritz, Chet T; Farley, Claire T

2003-01-01

Fast-moving legged animals bounce along the ground with spring-like legs and agilely traverse variable terrain. Previous research has shown that hopping and running humans maintain the same bouncing movement of the body's centre of mass on a range of elastic surfaces by adjusting their spring-like legs to exactly offset changes in surface stiffness. This study investigated human hopping on damped surfaces that dissipated up to 72% of the hopper's mechanical energy. On these surfaces, the legs did not act like pure springs. Leg muscles performed up to 24-fold more net work to replace the energy lost by the damped surface. However, considering the leg and surface together, the combination appeared to behave like a constant stiffness spring on all damped surfaces. By conserving the mechanics of the leg-surface combination regardless of surface damping, hoppers also conserved centre-of-mass motions. Thus, the normal bouncing movements of the centre of mass in hopping are not always a direct result of spring-like leg behaviour. Conserving the trajectory of the centre of mass by maintaining spring-like mechanics of the leg-surface combination may be an important control strategy for fast-legged locomotion on variable terrain. PMID:12965003

Structural analysis of compression helical spring used in suspension system

NASA Astrophysics Data System (ADS)

Jain, Akshat; Misra, Sheelam; Jindal, Arun; Lakhian, Prateek

2017-07-01

The main aim of this work has to develop a helical spring for shock absorber used in suspension system which is designed to reduce shock impulse and liberate kinetic energy. In a vehicle, it increases comfort by decreasing amplitude of disturbances and it improves ride quality by absorbing and dissipating energy. When a vehicle is in motion on a road and strikes a bump, spring comes into action quickly. After compression, spring will attempt to come to its equilibrium state which is on level road. Helical springs can be made lighter with more strength by reducing number of coils and increasing the area. In this research work, a helical spring is modeled and analyzed to substitute the existing steel spring which is used in suspension. By using different materials, stress and deflection of helical spring can be varied. Comparability between existing spring and newly replaced spring is used to verify the results. For finding detailed stress distribution, finite element analysis is used to find stresses and deflection in both the helical springs. Finite element analysis is a method which is used to find proximate solutions of a physical problem defined in a finite domain. In this research work, modeling of spring is accomplished using Solid Works and analysis on Ansys.

Coupling the WRF model with a temperature index model based on remote sensing for snowmelt simulations in a river basin in the Altay Mountains, northwest China

NASA Astrophysics Data System (ADS)

Wu, X.; Shen, Y.; Wang, N.; Pan, X.; Zhang, W.; He, J.; Wang, G.

2017-12-01

Snowmelt water is an important freshwater resource in the Altay Mountains in northwest China, and it is also crucial for local ecological system, economic and social sustainable development; however, warming climate and rapid spring snowmelt can cause floods that endanger both eco-environment and public and personal property and safety. This study simulates snowmelt in the Kayiertesi River catchment using a temperature-index model based on remote sensing coupled with high-resolution meteorological data obtained from NCEP reanalysis fields that were downscaled using Weather Research Forecasting model, then bias-corrected using a statistical downscaled model. Validation of the forcing data revealed that the high-resolution meteorological fields derived from downscaled NCEP reanalysis were reliable for driving the snowmelt model. Parameters of temperature-index model based on remote sensing were calibrated for spring 2014, and model performance was validated using MODIS snow cover and snow observations from spring 2012. The results show that the temperature-index model based on remote sensing performed well, with a simulation mean relative error of 6.7% and a Nash-Sutchliffe efficiency of 0.98 in spring 2012 in the river of Altay Mountains. Based on the reliable distributed snow water equivalent simulation, daily snowmelt runoff was calculated for spring 2012 in the basin. In the study catchment, spring snowmelt runoff accounts for 72% of spring runoff and 21% of annual runoff. Snowmelt is the main source of runoff for the catchment and should be managed and utilized effectively. The results provide a basis for snowmelt runoff predictions, so as to prevent snowmelt-induced floods, and also provide a generalizable approach that can be applied to other remote locations where high-density, long-term observational data is lacking.

A Magnet Spring Model

ERIC Educational Resources Information Center

Fay, T. H.; Mead, L.

2006-01-01

The paper discusses an elementary spring model representing the motion of a magnet suspended from the ceiling at one end of a vertical spring which is held directly above a second magnet fixed on the floor. There are two cases depending upon the north-south pole orientation of the two magnets. The attraction or repelling force induced by the…

Evaluating Gridded Spring Indices Using the USA National Phenology Network's Observational Phenology Data

NASA Astrophysics Data System (ADS)

Crimmins, T. M.; Gerst, K.

2017-12-01

The USA National Phenology Network (USA-NPN; www.usanpn.org) produces and freely delivers daily and short-term forecast maps of spring onset dates at fine spatial scale for the conterminous United States and Alaska using the Spring Indices. These models, which represent the start of biological activity in the spring season, were developed using a long-term observational record of four species of lilacs and honeysuckles contributed by volunteer observers. Three of the four species continue to be tracked through the USA-NPN's phenology observation program, Nature's Notebook. The gridded Spring Index maps have utility for a wide range of natural resource planning and management applications, including scheduling invasive species and pest detection and control activities, anticipating allergy outbreaks and planning agricultural harvest dates. However, to date, there has not been a comprehensive assessment of how well the gridded Spring Index maps accurately reflect phenological activity in lilacs and honeysuckles or other species of plants. In this study, we used observational plant phenology data maintained by the USA-NPN to evaluate how well the gridded Spring Index maps match leaf and flowering onset dates in a) the lilac and honeysuckle species used to construct the models and b) in several species of deciduous trees. The Spring Index performed strongly at predicting the timing of leaf-out and flowering in lilacs and honeysuckles. The average error between predicted and observed date of onset ranged from 5.9 to 11.4 days. Flowering models performed slightly better than leaf-out models. The degree to which the Spring Indices predicted native deciduous tree leaf and flower phenology varied by year, species, and region. Generally, the models were better predictors of leaf and flowering onset dates in the Northeastern and Midwestern US. These results reveal when and where the Spring Indices are a meaningful proxy of phenological activity across the United States.

Genetic and Molecular Analysis of the Mechanisms by which TSC Regulates Neuronal Differentiation

DTIC Science & Technology

2009-03-01

2004 Programmed autophagy in the Drosophila fat body is in- duced by ecdysone through regulation of the PI3K pathway. Dev. Cell 7: 179–192. Sarbassov...embryonic Drosophila CNS. Mech. Dev. 64: 137–151. Scott, R. C., O. Schuldiner and T. P. Neufeld, 2004 Role and reg- ulation of starvation-induced autophagy ...in The Development of Drosophila melanogaster , edited by M. Bates and A. Martinez-Arias. Cold Spring Harbor Laboratory Press, Cold Spring Harbor, NY

Predicting the patterns of change in spring onset and false springs in China during the twenty-first century

NASA Astrophysics Data System (ADS)

Zhu, Likai; Meng, Jijun; Li, Feng; You, Nanshan

2017-10-01

Spring onset has generally shifted earlier in China over the past several decades in response to the warming climate. However, future changes in spring onset and false springs, which will have profound effects on ecosystems, are still not well understood. Here, we used the extended form of the Spring Indices model (SI-x) to project changes in the first leaf and first bloom dates, and predicted false springs for the historical (1950-2005) and future (2006-2100) periods based on the downscaled daily maximum/minimum temperatures under two emission scenarios from 21 General Circulation Models (GCMs) of the Coupled Model Intercomparison Project Phase 5 (CMIP5). On average, first leaf and first bloom in China were projected to occur 21 and 23 days earlier, respectively, by the end of the twenty-first century in the Representative Concentration Pathway (RCP) 8.5 scenario. Areas with greater earlier shifts in spring onset were in the warm temperate zone, as well as the north and middle subtropical zones of China. Early false spring risk increased rapidly in the warm temperate and north subtropical zones, while that declined in the cold temperate zone. Relative to early false spring risk, late false spring risk showed a common increase with smaller magnitude in the RCP 8.5 scenario but might cause greater damage to ecosystems because plants tend to become more vulnerable to the later occurrence of a freeze event. We conclude that future climate warming will continue to cause earlier occurrence of spring onset in general, but might counterintuitively increase plant damage risk in natural and agricultural systems of the warm temperate and subtropical China.

Predicting the patterns of change in spring onset and false springs in China during the twenty-first century.

PubMed

Zhu, Likai; Meng, Jijun; Li, Feng; You, Nanshan

2017-10-28

Spring onset has generally shifted earlier in China over the past several decades in response to the warming climate. However, future changes in spring onset and false springs, which will have profound effects on ecosystems, are still not well understood. Here, we used the extended form of the Spring Indices model (SI-x) to project changes in the first leaf and first bloom dates, and predicted false springs for the historical (1950-2005) and future (2006-2100) periods based on the downscaled daily maximum/minimum temperatures under two emission scenarios from 21 General Circulation Models (GCMs) of the Coupled Model Intercomparison Project Phase 5 (CMIP5). On average, first leaf and first bloom in China were projected to occur 21 and 23 days earlier, respectively, by the end of the twenty-first century in the Representative Concentration Pathway (RCP) 8.5 scenario. Areas with greater earlier shifts in spring onset were in the warm temperate zone, as well as the north and middle subtropical zones of China. Early false spring risk increased rapidly in the warm temperate and north subtropical zones, while that declined in the cold temperate zone. Relative to early false spring risk, late false spring risk showed a common increase with smaller magnitude in the RCP 8.5 scenario but might cause greater damage to ecosystems because plants tend to become more vulnerable to the later occurrence of a freeze event. We conclude that future climate warming will continue to cause earlier occurrence of spring onset in general, but might counterintuitively increase plant damage risk in natural and agricultural systems of the warm temperate and subtropical China.

Using nitrate to quantify quick flow in a karst aquifer

USGS Publications Warehouse

Mahler, B.J.; Garner, B.D.

2009-01-01

In karst aquifers, contaminated recharge can degrade spring water quality, but quantifying the rapid recharge (quick flow) component of spring flow is challenging because of its temporal variability. Here, we investigate the use of nitrate in a two-endmember mixing model to quantify quick flow in Barton Springs, Austin, Texas. Historical nitrate data from recharging creeks and Barton Springs were evaluated to determine a representative nitrate concentration for the aquifer water endmember (1.5 mg/L) and the quick flow endmember (0.17 mg/L for nonstormflow conditions and 0.25 mg/L for stormflow conditions). Under nonstormflow conditions for 1990 to 2005, model results indicated that quick flow contributed from 0% to 55% of spring flow. The nitrate-based two-endmember model was applied to the response of Barton Springs to a storm and results compared to those produced using the same model with ??18O and specific conductance (SC) as tracers. Additionally, the mixing model was modified to allow endmember quick flow values to vary over time. Of the three tracers, nitrate appears to be the most advantageous because it is conservative and because the difference between the concentrations in the two endmembers is large relative to their variance. The ??18O- based model was very sensitive to variability within the quick flow endmember, and SC was not conservative over the timescale of the storm response. We conclude that a nitrate-based two-endmember mixing model might provide a useful approach for quantifying the temporally variable quick flow component of spring flow in some karst systems. ?? 2008 National Ground Water Association.

The Rediscovery of a Long Described Species Reveals Additional Complexity in Speciation Patterns of Poeciliid Fishes in Sulfide Springs

PubMed Central

Palacios, Maura; Arias-Rodriguez, Lenin; Plath, Martin; Eifert, Constanze; Lerp, Hannes; Lamboj, Anton; Voelker, Gary; Tobler, Michael

2013-01-01

The process of ecological speciation drives the evolution of locally adapted and reproductively isolated populations in response to divergent natural selection. In Southern Mexico, several lineages of the freshwater fish species of the genus Poecilia have independently colonized toxic, hydrogen sulfide-rich springs. Even though ecological speciation processes are increasingly well understood in this system, aligning the taxonomy of these fish with evolutionary processes has lagged behind. While some sulfide spring populations are classified as ecotypes of Poecilia mexicana, others, like P. sulphuraria, have been described as highly endemic species. Our study particularly focused on elucidating the taxonomy of the long described sulfide spring endemic, Poecilia thermalis Steindachner 1863, and investigates if similar evolutionary patterns of phenotypic trait divergence and reproductive isolation are present as observed in other sulfidic species of Poecilia. We applied a geometric morphometric approach to assess body shape similarity to other sulfidic and non-sulfidic fish of the genus Poecilia. We also conducted phylogenetic and population genetic analyses to establish the phylogenetic relationships of P. thermalis and used a population genetic approach to determine levels of gene flow among Poecilia from sulfidic and non-sulfidic sites. Our results indicate that P. thermalis' body shape has evolved in convergence with other sulfide spring populations in the genus. Phylogenetic analyses placed P. thermalis as most closely related to one population of P. sulphuraria, and population genetic analyses demonstrated that P. thermalis is genetically isolated from both P. mexicana ecotypes and P. sulphuraria. Based on these findings, we make taxonomic recommendations for P. thermalis. Overall, our study verifies the role of hydrogen sulfide as a main factor shaping convergent, phenotypic evolution and the emergence of reproductive isolation between Poecilia populations residing in adjacent sulfidic and non-sulfidic environments. PMID:23976979

Body surface detection method for photoacoustic image data using cloth-simulation technique

NASA Astrophysics Data System (ADS)

Sekiguchi, H.; Yoshikawa, A.; Matsumoto, Y.; Asao, Y.; Yagi, T.; Togashi, K.; Toi, M.

2018-02-01

Photoacoustic tomography (PAT) is a novel modality that can visualize blood vessels without contrast agents. It clearly shows blood vessels near the body surface. However, these vessels obstruct the observation of deep blood vessels. As the existence range of each vessel is determined by the distance from the body surface, they can be separated if the position of the skin is known. However, skin tissue, which does not contain hemoglobin, does not appear in PAT results, therefore, manual estimation is required. As this task is very labor-intensive, its automation is highly desirable. Therefore, we developed a method to estimate the body surface using the cloth-simulation technique, which is a commonly used method to create computer graphics (CG) animations; however, it has not yet been employed for medical image processing. In cloth simulations, the virtual cloth is represented by a two-dimensional array of mass nodes. The nodes are connected with each other by springs. Once the cloth is released from a position away from the body, each node begins to move downwards under the effect of gravity, spring, and other forces; some of the nodes hit the superficial vessels and stop. The cloth position in the stationary state represents the body surface. The body surface estimation, which required approximately 1 h with the manual method, is automated and it takes only approximately 10 s with the proposed method. The proposed method could facilitate the practical use of PAT.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rowland, Joel C; Manga, Michael

The origin of increased stream flow and spring discharge following earthquakes have been the subject of controversy, in large part because there are many models to explain observations and few measurements suitable for distinguishing between hypotheses. On October 30, 2007 a magnitude 5.5 earthquake occurred near the Alum Rock springs, California, USA. Within a day we documented a several-fold increase in discharge. Over the following year, we have monitored a gradual return towards pre-earthquake properties, but for the largest springs there appears to be a permanent increase in the steady discharge at all the springs. The Alum Rock springs dischargemore » waters that represent a mixture between modern ('shallow') meteoric water and old ('deep') connate waters expelled by regional transpression. After the earthquake, the increased discharge at the largest springs was accompanied by a small decrease in the fraction of connate water in the spring discharge. Combined with the rapid response, this implies that the increased discharge has a shallow origin. Increased discharge at these springs occurs for earthquakes that cause static volumetric expansion and those that cause contraction, supporting models in which dynamic strains are responsible for the subsurface changes that cause flow to increase. We show that models in which the permeability of the fracture system feeding the springs increases after the earthquake are in general consistent with the changes in discharge. The response of these springs to another earthquake will provide critical constraints on the changes that occur in the subsurface.« less

Molecular Modeling of Thermosetting Polymers: Effects of Degree of Curing and Chain Length on Thermo-Mechanical Properties

DTIC Science & Technology

2012-08-01

paper, we will first briefly discuss our recent results, using coarse-grained bead - spring model , on the dependence of failure stress and failure...length of the resin strands. In the coarse-grained model used here the polymer network is treated as a bead - spring system. To create highly cross...simulations of Thermosets We have used a coarse-grained bead - spring model to study the dependence of the mechanical properties of thermosets on chain

Improved design of dynamic vibration absorber by using the inerter and its application in vehicle suspension

NASA Astrophysics Data System (ADS)

Shen, Yujie; Chen, Long; Yang, Xiaofeng; Shi, Dehua; Yang, Jun

2016-01-01

Inerter is a recently proposed mechanical element with two terminals. The novelty of this paper is to present the improved design which aims to add traditional dynamic vibration absorber to the vehicle body by using the inerter. Based on this background, a new vehicle suspension structure called ISD suspension, including the inerter, spring and damper has been created. A dual-mass vibration model including the ISD suspension is considered in this study. Parameters are obtained by using the genetic optimizing algorithm. The frequency-domain simulation confirms that the ISD suspension can effectively improve the damping performance of the suspension system, especially at the offset frequency of the vehicle body, which is consistent with the feature of the dynamic vibration absorber added to the vehicle body mass. At last, a prototype ball screw inerter has been designed and the bench test of a quarter-car model has been undertaken. Under the conditions of the random road input, the vehicle ride comfort evaluation of body acceleration RMS value decreases by 4% at most, the suspension deflection RMS value decreases by 16% at most, the tire dynamic load RMS value decreases by 6% at most. Power spectral density results also indicate that the ISD suspension has superior damping performance than passive suspension which proves that the proposed ISD suspension is deemed effective.

Analysis of the dominant vibration frequencies of rail bridges for structure-borne noise using a power flow method

NASA Astrophysics Data System (ADS)

Li, Q.; Wu, D. J.

2013-09-01

The use of concrete bridges in urban rail transit systems has raised many concerns regarding low-frequency (20-200 Hz) structure-borne noise due to the vibration of bridges when subjected to moving trains. Understanding the mechanism that determines the dominant frequencies of bridge vibrations is essential for both vibration and noise reduction. This paper presents a general procedure based on the force method to obtain the power flows within a coupled vehicle-track-bridge system, the point mobility of the system and the dynamic interaction forces connecting various components. The general coupling system consists of multi-rigid-bodies for the vehicles, infinite Euler beams representing the rails, two-dimensional or three-dimensional elements of the concrete bridges, and spring-dashpot pairs to model the wheel-rail contacts, the vehicle suspensions, the rail pads and the bridge bearings. The dynamic interaction of the coupled system is solved in the frequency domain by assuming the combined wheel-rail roughness moves forward relative to the stationary vehicles. The proposed procedure is first applied to a rail on discrete supports and then to a real urban rail transit U-shaped concrete bridge. The computed results show that the wheel-rail contact forces, the power flows to the rail/bridge subsystem and the accelerations of the bridge are primarily dominated by the contents around the natural frequency of a single wheel adhered to the elastically supported rail. If the ath node of the mth spring-dashpot pair and the bth node of the nth spring-dashpot pair are connected to the same rigid body, then δmnab(ω) can be expressed as δmnab(ω)=-{(}/{Mlω}, where Ml is the mass of the lth rigid body. If the ath node of the mth spring-dashpot pair and the bth node of the nth spring-dashpot pair are connected to the same infinite rail, δmnab(ω) can be expressed as [8] δmnab(ω)=-j{((e-je)}/{4EIk}, where xm and xn are the x-coordinates of the mth and nth spring-dashpot pairs respectively; E and I denote the elastic module and the bending moment of inertia of the infinite rail; and k is the wavenumber of the unsupported infinite rail k=(EI)1/4, where mr is the mass per unit length of the rail. If the ath node of the mth spring-dashpot pair and the bth node of the nth spring-dashpot pair are connected to the same bridge component, then δmnab(ω) can be obtained by applying the mode superposition method δmnab(ω)=∑i=1Nl{(ϕ}/{liaϕlibωli2-ω+2jξωω}, where ω and ξ are the damped natural frequency and damping ratio of the ith mode of the lth bridge component; ϕlia and ϕlib denote the generalised mode shape amplitudes of the the lth bridge component to which the ath and bth nodes of the two spring-dashpot pairs are connected; and Nl is the mode number of interest. It can be observed from Eqs. (2)-(7) that the theorem of reciprocal displacements is met as follows: δ(ω)=δ(ω). An external point excitation can be regarded as a force produced by a spring-dashpot pair with its first node connected to the excitation point and the second node fixed to the ground. Therefore, each element in vector ΔP(ω) can be easily attained using the first and last terms of Eq. (3): Δmp(ω)=δmp11(ω)+δmp21(ω), where the subscript p denotes the fictitious spring-dashpot pair used to simulate the external harmonic force. The dominant frequency of the wheel-rail contact forces and power input to the rail on elastic supports is found to be consistent with the natural frequency of the single wheel adhered to the elastically supported rail. The simple formula derived to predict this dominant frequency matches well with the numerical results. The acceleration response of the bridge is also dominated by the natural frequency of the single wheel adhered to the elastically supported rail. Although the vehicle speed has an insignificant effect on the dominant frequency of the bridge response, it does influence the magnitude of the response. The findings in this paper and the proposed method can be applied to mitigate the vibration and noise from rail bridges once a series of parametric analyses has been carried out.

The Fischa-Dagnitz spring, Southern Vienna Basin: a multi tracer time series study re-assessing earlier conceptual assumptions.

NASA Astrophysics Data System (ADS)

Suckow, Axel; Gerber, Christoph; Kralik, Martin; Sültenfuss, Jürgen; Purtschert, Roland

2013-04-01

The gravel aquifer of the Southern Vienna Basin is a very important backup drinking water resource for the city of Vienna. A discharge location, the Fischa-Dagnitz spring in the Southern Vienna Basin, Austria, was re-investigated in 2011, five years after the gas exchange tracer test published in (Stolp et al., 2010), and sampled for stable isotopes 18O/2H, tritium, 3He, SF6 and 85Kr (Gerber et al., 2012). Additionally, new tritium time series data (Davis et al., 1967), previously not considered in Stolp et al. (2010), were included. These show a higher and earlier tritium peak of >300 TU in 1965 in the discharge of the Fischa-Dagnitz spring as compared to 221 TU in 1972 considered in Stolp et al. (2010). The new 3He, SF6 and 85Kr gas tracer data from 2011 confirm the earlier finding for 3He of Stolp et al. (2010) and indicate a more recent equilibration with the atmosphere than the water bound tracers 18O, 2H and tritium. A new modelling attempt using the Lumpy code (Suckow, 2012) confirmed the discrepancy between the tritium data and the gaseous tracers 3He, SF6 and 85Kr. No steady-state combination of local recharge (represented by an exponential model) and Schwarza river infiltration flowing through the gravel aquifer (represented by a parallel dispersion model) can equally well explain both the tritium time series and the gas tracer results. A revised conceptual model proposes that a pinching of the aquifer at unconformities in the gravel body or a fault zone known in the gravel body forces groundwater along the flow path closer to the surface and exposes it to the atmosphere. This would tend to reset the "dating" clock for the gaseous tracers 3He, SF6 and 85Kr, which can equilibrate quickly with the atmosphere, but not for tritium, which marks the transport behaviour of the water itself. These findings are of importance also for other multi-tracer assessments of groundwater movement in phreatic aquifer systems. References: Davis, G.H., Payne, B.R., Dincer, T., Florkowski, T., Gattinger, T., 1967. Seasonal Variations in the Tritium Content of Groundwaters of the Vienna Basin, Austria, Isotope Hydrology 1967. IAEA, Vienna, Austria, IAEA, Vienna, Austria, pp. 451-473. Gerber, C., Purtschert, R., Kralik, M., Humer, F., Sültenfuss, J., Darling, G.W., Gooddy, D., 2012. Suitability and potential of environmental tracers for base-flow determination in streams: EGU2012-14066, EGU 12. European Geosciences Union, Vienna Stolp, B.J., Solomon, D.K., Suckow, A., Vitvar, T., Rank, D., Aggarwal, P.K., Han, L.-F., 2010. Age dating base flow at springs and gaining streams using helium-3 and tritium: Fischa-Dagnitz system, southern Vienna Basin, Austria. Water Resources Research 46. Suckow, A., 2012. Lumpy - an interactive Lumped Parameter Modeling code based on MS Access and MS Excel., EGU 12. European Geosciences Union, Vienna

The Effect of Body Type and Camera Shot on Interpersonal Attraction and Source Credibility.

ERIC Educational Resources Information Center

McCain, Thomas A.; Divers, Lawrence

In order to examine the effects of manipulating image size (i.e., relative size) and body type of speakers in a television context on source credibility and interpersonal attraction, a study was conducted at Illinois State University during the spring of 1973. Subjects were eighteen intact groups of students enrolled in speech communication class…

A mathematical model for simulating spring discharge and estimating sinkhole porosity in a karst watershed

NASA Astrophysics Data System (ADS)

Li, Guangquan; Field, Malcolm S.

2014-03-01

Documenting and understanding water balances in a karst watershed in which groundwater and surface water resources are strongly interconnected are important aspects for managing regional water resources. Assessing water balances in karst watersheds can be difficult, however, because karst watersheds are so very strongly affected by groundwater flows through solution conduits that are often connected to one or more sinkholes. In this paper we develop a mathematical model to approximate sinkhole porosity from discharge at a downstream spring. The model represents a combination of a traditional linear reservoir model with turbulent hydrodynamics in the solution conduit connecting the downstream spring with the upstream sinkhole, which allows for the simulation of spring discharges and estimation of sinkhole porosity. Noting that spring discharge is an integral of all aspects of water storage and flow, it is mainly dependent on the behavior of the karst aquifer as a whole and can be adequately simulated using the analytical model described in this paper. The model is advantageous in that it obviates the need for a sophisticated numerical model that is much more costly to calibrate and operate. The model is demonstrated using the St. Marks River Watershed in northwestern Florida.

Identification of the dominant hydrological process and appropriate model structure of a karst catchment through stepwise simplification of a complex conceptual model

NASA Astrophysics Data System (ADS)

Chang, Yong; Wu, Jichun; Jiang, Guanghui; Kang, Zhiqiang

2017-05-01

Conceptual models often suffer from the over-parameterization problem due to limited available data for the calibration. This leads to the problem of parameter nonuniqueness and equifinality, which may bring much uncertainty of the simulation result. How to find out the appropriate model structure supported by the available data to simulate the catchment is still a big challenge in the hydrological research. In this paper, we adopt a multi-model framework to identify the dominant hydrological process and appropriate model structure of a karst spring, located in Guilin city, China. For this catchment, the spring discharge is the only available data for the model calibration. This framework starts with a relative complex conceptual model according to the perception of the catchment and then this complex is simplified into several different models by gradually removing the model component. The multi-objective approach is used to compare the performance of these different models and the regional sensitivity analysis (RSA) is used to investigate the parameter identifiability. The results show this karst spring is mainly controlled by two different hydrological processes and one of the processes is threshold-driven which is consistent with the fieldwork investigation. However, the appropriate model structure to simulate the discharge of this spring is much simpler than the actual aquifer structure and hydrological processes understanding from the fieldwork investigation. A simple linear reservoir with two different outlets is enough to simulate this spring discharge. The detail runoff process in the catchment is not needed in the conceptual model to simulate the spring discharge. More complex model should need more other additional data to avoid serious deterioration of model predictions.

AgRISTARS: Supporting research. Spring small grains planting date distribution model

NASA Technical Reports Server (NTRS)

Hodges, T.; Artley, J. A. (Principal Investigator)

1981-01-01

A model was developed using 996 planting dates at 51 LANDSAT segments for spring wheat and spring barley in Minnesota, Montana, North Dakota, and South Dakota in 1979. Daily maximum and minimum temperatures and precipitation were obtained from the cooperative weather stations nearest to each segment. The model uses a growing degree day summation modified for daily temperature range to estimate the beginning of planting and uses a soil surface wetness variable to estimate how a fixed number of planting days are distributed after planting begins. For 1979, the model predicts first, median, and last planting dates with root mean square errors of 7.91, 6.61, and 7.09 days, respectively. The model also provides three or four dates to represent periods of planting activity within the planting season. Although the full model was not tested on an independent data set, it may be suitable in areas other than the U.S. Great Plains where spring small grains are planted as soon as soil and air temperatures become warm enough in the spring for plant growth.

Physiological studies in the South American camelid llama (Lama guanicoe f. d. glama). I. Body water spaces and water turnover.

PubMed

Marcilese, N A; Ghezzi, M D; Aba, M A; Alzola, R A; Solana, H; Valsecchi, R M

1994-01-01

Body water (BW) and extracellular water (ECW), were determined with tritiated water (THO) and 82Br injected into the vein, to 8 mature animals of both sexes during the winter season. The biological half-time of THO (T1/2 THO) and the daily water turnover (WT) were measured and the intracellular water (ICW) calculated. The studies with THO were repeated in the same animals and in 2 lactating females in spring and summer. Two calves were also studied during spring. The values obtained in winter were: BW 659 +/- 12 ml/kg; T1/2 THO 9.2 +/- 1 day; WT per 24 h 50 +/- 3 ml/kg or 116 +/- 5 ml/kg 82 and 163 +/- 9 ml per 1 of BW82; ECW 215 +/- 8 ml/kg or 32.5 +/- 3% BW; ICW 447 +/- 12 ml/kg or 67.7 +/- 4% BW. The results of the spring's studies showed a significant increase in the values of WT. In summer a further increment of this parameters was observed when expressed as ml/kg body solids. This differences were remarkable in those in lactation. The proportion of water in the body was significantly higher during summer in all animals. BW in lactating animals during summer was 783 +/- 9 ml/kg and in the other animals 718 +/- 18; T1/2 THO values were 3.3 +/- .-06 and 4.5 +/- .4 day, respectively. WT was 396 +/- 9 ml/kg.82 or 484 +/- 8 ml/l BW82 in the lactating animals and 260 +/- 9 ml/kg 82 or 341 +/- 12 ml/l BW82 in the other animals.(ABSTRACT TRUNCATED AT 250 WORDS)

The effect of extreme spring weather on body condition and stress physiology in Lapland longspurs and white-crowned sparrows breeding in the Arctic.

PubMed

Krause, Jesse S; Pérez, Jonathan H; Chmura, Helen E; Sweet, Shannan K; Meddle, Simone L; Hunt, Kathleen E; Gough, Laura; Boelman, Natalie; Wingfield, John C

2016-10-01

Climate change is causing rapid shifts in temperature while also increasing the frequency, duration, and intensity of extreme weather. In the northern hemisphere, the spring of 2013 was characterized as extreme due to record high snow cover and low temperatures. Studies that describe the effects of extreme weather on phenology across taxa are limited while morphological and physiological responses remain poorly understood. Stress physiology, as measured through baseline and stress-induced concentrations of cortisol or corticosterone, has often been studied to understand how organisms respond to environmental stressors. We compared body condition and stress physiology of two long-distance migrants breeding in low arctic Alaska - the white-crowned sparrow (Zonotrichia leucophrys) and Lapland longspur (Calcarius lapponicus) - in 2013, an extreme weather year, with three more typical years (2011, 2012, and 2014). The extended snow cover in spring 2013 caused measureable changes in phenology, body condition and physiology. Arrival timing for both species was delayed 4-5days compared to the other three years. Lapland longspurs had reduced fat stores, pectoralis muscle profiles, body mass, and hematocrit levels, while stress-induced concentrations of corticosterone were increased. Similarly, white-crowned sparrows had reduced pectoralis muscle profiles and hematocrit levels, but in contrast to Lapland longspurs, had elevated fat stores and no difference in mass or stress physiology relative to other study years. An understanding of physiological mechanisms that regulate coping strategies is of critical importance for predicting how species will respond to the occurrence of extreme events in the future due to global climate change. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Comparison of age distributions estimated from environmental tracers by using binary-dilution and numerical models of fractured and folded karst: Shenandoah Valley of Virginia and West Virginia, USA

USGS Publications Warehouse

Yager, Richard M.; Plummer, Niel; Kauffman, Leon J.; Doctor, Daniel H.; Nelms, David L.; Schlosser, Peter

2013-01-01

Measured concentrations of environmental tracers in spring discharge from a karst aquifer in the Shenandoah Valley, USA, were used to refine a numerical groundwater flow model. The karst aquifer is folded and faulted carbonate bedrock dominated by diffuse flow along fractures. The numerical model represented bedrock structure and discrete features (fault zones and springs). Concentrations of 3H, 3He, 4He, and CFC-113 in spring discharge were interpreted as binary dilutions of young (0–8 years) water and old (tracer-free) water. Simulated mixtures of groundwater are derived from young water flowing along shallow paths, with the addition of old water flowing along deeper paths through the model domain that discharge to springs along fault zones. The simulated median age of young water discharged from springs (5.7 years) is slightly older than the median age estimated from 3H/3He data (4.4 years). The numerical model predicted a fraction of old water in spring discharge (0.07) that was half that determined by the binary-dilution model using the 3H/3He apparent age and 3H and CFC-113 data (0.14). This difference suggests that faults and lineaments are more numerous or extensive than those mapped and included in the numerical model.

A new pneumatic suspension system with independent stiffness and ride height tuning capabilities

NASA Astrophysics Data System (ADS)

Yin, Zhihong; Khajepour, Amir; Cao, Dongpu; Ebrahimi, Babak; Guo, Konghui

2012-12-01

This paper introduces a new pneumatic spring for vehicle suspension systems, allowing independent tuning of stiffness and ride height according to different vehicle operating conditions and driver preferences. The proposed pneumatic spring comprises a double-acting pneumatic cylinder, two accumulators and a tuning subsystem. This paper presents a detailed description of the pneumatic spring and its working principle. The mathematical model is established based on principles of thermo and fluid dynamics. An experimental setup has been designed and fabricated for testing and evaluating the proposed pneumatic spring. The analytical and experimental results confirm the capability of the new pneumatic spring system for independent tuning of stiffness and ride height. The mathematical model is verified and the capabilities of the pneumatic spring are further proved. It is concluded that this new pneumatic spring provides a more flexible suspension design alternative for meeting various conflicting suspension requirements for ride comfort and performance.

Mixing of shallow and deep groundwater as indicated by the chemistry and age of karstic springs

NASA Astrophysics Data System (ADS)

Toth, David J.; Katz, Brian G.

2006-06-01

Large karstic springs in east-central Florida, USA were studied using multi-tracer and geochemical modeling techniques to better understand groundwater flow paths and mixing of shallow and deep groundwater. Spring water types included Ca-HCO3 (six), Na-Cl (four), and mixed (one). The evolution of water chemistry for Ca-HCO3 spring waters was modeled by reactions of rainwater with soil organic matter, calcite, and dolomite under oxic conditions. The Na-Cl and mixed-type springs were modeled by reactions of either rainwater or Upper Floridan aquifer water with soil organic matter, calcite, and dolomite under oxic conditions and mixed with varying proportions of saline Lower Floridan aquifer water, which represented 4-53% of the total spring discharge. Multiple-tracer data—chlorofluorocarbon CFC-113, tritium (3H), helium-3 (3Hetrit), sulfur hexafluoride (SF6)—for four Ca-HCO3 spring waters were consistent with binary mixing curves representing water recharged during 1980 or 1990 mixing with an older (recharged before 1940) tracer-free component. Young-water mixing fractions ranged from 0.3 to 0.7. Tracer concentration data for two Na-Cl spring waters appear to be consistent with binary mixtures of 1990 water with older water recharged in 1965 or 1975. Nitrate-N concentrations are inversely related to apparent ages of spring waters, which indicated that elevated nitrate-N concentrations were likely contributed from recent recharge.

GIS-based groundwater potential analysis using novel ensemble weights-of-evidence with logistic regression and functional tree models.

PubMed

Chen, Wei; Li, Hui; Hou, Enke; Wang, Shengquan; Wang, Guirong; Panahi, Mahdi; Li, Tao; Peng, Tao; Guo, Chen; Niu, Chao; Xiao, Lele; Wang, Jiale; Xie, Xiaoshen; Ahmad, Baharin Bin

2018-09-01

The aim of the current study was to produce groundwater spring potential maps using novel ensemble weights-of-evidence (WoE) with logistic regression (LR) and functional tree (FT) models. First, a total of 66 springs were identified by field surveys, out of which 70% of the spring locations were used for training the models and 30% of the spring locations were employed for the validation process. Second, a total of 14 affecting factors including aspect, altitude, slope, plan curvature, profile curvature, stream power index (SPI), topographic wetness index (TWI), sediment transport index (STI), lithology, normalized difference vegetation index (NDVI), land use, soil, distance to roads, and distance to streams was used to analyze the spatial relationship between these affecting factors and spring occurrences. Multicollinearity analysis and feature selection of the correlation attribute evaluation (CAE) method were employed to optimize the affecting factors. Subsequently, the novel ensembles of the WoE, LR, and FT models were constructed using the training dataset. Finally, the receiver operating characteristic (ROC) curves, standard error, confidence interval (CI) at 95%, and significance level P were employed to validate and compare the performance of three models. Overall, all three models performed well for groundwater spring potential evaluation. The prediction capability of the FT model, with the highest AUC values, the smallest standard errors, the narrowest CIs, and the smallest P values for the training and validation datasets, is better compared to those of other models. The groundwater spring potential maps can be adopted for the management of water resources and land use by planners and engineers. Copyright © 2018 Elsevier B.V. All rights reserved.

The Model of Educational Reconstruction--A Powerful Strategy to Teach for Conceptual Development in Physical Geography: The Case of Water Springs

ERIC Educational Resources Information Center

Reinfried, Sibylle; Aeschbacher, Urs; Kienzler, Peter M.; Tempelmann, Sebastian

2015-01-01

Springs are an important hydrological concept because springs form an interface between underground and surface sub-systems of the hydrological cycle. Furthermore, springs are important suppliers of drinking water but are at risk today due to numerous anthropogenic interferences. The general knowledge of springs and their formation is usually…

Analyzing spring pendulum phenomena with a smart-phone acceleration sensor

NASA Astrophysics Data System (ADS)

Kuhn, Jochen; Vogt, Patrik

2012-11-01

This paper describes two further pendulum experiments using the acceleration sensor of a smartphone in this column (for earlier contributions concerning this topic, including the description of the operation and use of the acceleration sensor, see Refs. 1 and 2). In this paper we focus on analyzing spring pendulum phenomena. Therefore two spring pendulum experiments will be described in which a smartphone is used as a pendulum body and SPARKvue3 software is used in conjunction with an iPhone or an iPod touch, or the Accelogger4 app for an Android device.1,2 As described in Ref. 1, the values measured by the smartphone are subsequently exported to a spreadsheet application (e.g., MS Excel) for analysis.

Reproduction, mastitis, and body condition of seasonally calved Holstein and Jersey cows in confinement or pasture systems.

PubMed

Washburn, S P; White, S L; Green, J T; Benson, G A

2002-01-01

Dairy cows in confinement and pasture-based feeding systems were compared across four spring-calving and three fall-calving replicates for differences in reproduction, mastitis, body weights, and body condition scores. Feeding systems and replicates included both Jersey and Holstein cows. Cows in confinement were fed a total mixed ration, and cows on pasture were supplemented with concentrates and provided baled hay or haylage when pasture supply was limiting. Breeding periods were for 75 d in spring or fall. Reproductive performance did not differ significantly due to feeding system or season. Jerseys had higher conception rates (59.6 vs. 49.5 +/- 3.3%) and higher percentages of cows pregnant in 75 d (78.1 vs. 57.9 +/- 3.9%) than Holsteins. Cows in confinement had 1.8 times more clinical mastitis and eight times the rate of culling for mastitis than did cows on pasture. Jerseys had half as many clinical cases of mastitis per cow as Holsteins. Only 41 +/- 5% of confinement Holsteins remained for a subsequent lactation, starting within the defined calving season compared with 51 +/- 5% of pastured Holsteins and 71 and 72 +/- 5% of Jerseys, respectively. Body weights and condition scores were generally higher for confinement cows than pastured cows, and Jerseys had higher condition scores and lower body weights than Holsteins. In summary, pastured cows had fewer clinical cases of mastitis, lower body condition scores, and lower body weights than confinement cows. Holsteins were less likely to rebreed, had more mastitis, higher culling rates, and lower body condition scores than Jerseys.

Associations between body composition and helminths of lesser snow geese during winter and spring migration.

PubMed

Shutler, Dave; Alisauskas, Ray T; Daniel McLaughlin, J

2012-07-01

Costs of parasitism are predicted to be higher with greater parasite intensities and higher inter-parasite competition (diversity). We tested whether greater helminth intensities and diversity were associated with poorer body composition (whole-body fat, protein, mineral and true body mass) in lesser snow geese, Chen caerulescens caerulescens. As part of a larger study on nutritional ecology, 828 wintering or migrating geese were shot between January and May 1983 in 27 different date-locations (samples) during their northward migration through mid-continental North America. A large proportion of overall variation in body composition and parasite communities was among samples, so we analyzed data within each of the 27 samples, controlling for structural body size (the first principal component of 10 body size measurements), sex and the age of geese. There was no compelling evidence that cestodes, trematodes or helminth diversity were associated with variation in body composition but nematodes had several negative associations with fat reserves. However, negative associations between fat reserves and nematodes occurred most often in geese collected between March and May when nematode prevalences and intensities were relatively low. This suggests several possibilities: that the most common nematodes (Heterakis dispar and Trichostrongylus tenuis) were more virulent at this time, that infected individuals had been chronically infected and suffered cumulative nutrient deficits that lasted until late in the spring migration, or that geese became more vulnerable to the effects of parasites at this time of year, possibly because they redirected resources away from immunity toward fat storage in preparation for reproduction. Copyright © 2012 Australian Society for Parasitology Inc. All rights reserved.

Systematic variation of prosthetic foot spring affects center-of-mass mechanics and metabolic cost during walking.

PubMed

Zelik, Karl E; Collins, Steven H; Adamczyk, Peter G; Segal, Ava D; Klute, Glenn K; Morgenroth, David C; Hahn, Michael E; Orendurff, Michael S; Czerniecki, Joseph M; Kuo, Arthur D

2011-08-01

Lower-limb amputees expend more energy to walk than non-amputees and have an elevated risk of secondary disabilities. Insufficient push-off by the prosthetic foot may be a contributing factor. We aimed to systematically study the effect of prosthetic foot mechanics on gait, to gain insight into fundamental prosthetic design principles. We varied a single parameter in isolation, the energy-storing spring in a prototype prosthetic foot, the controlled energy storage and return (CESR) foot, and observed the effect on gait. Subjects walked on the CESR foot with three different springs. We performed parallel studies on amputees and on non-amputees wearing prosthetic simulators. In both groups, spring characteristics similarly affected ankle and body center-of-mass (COM) mechanics and metabolic cost. Softer springs led to greater energy storage, energy return, and prosthetic limb COM push-off work. But metabolic energy expenditure was lowest with a spring of intermediate stiffness, suggesting biomechanical disadvantages to the softest spring despite its greater push-off. Disadvantages of the softest spring may include excessive heel displacements and COM collision losses. We also observed some differences in joint kinetics between amputees and non-amputees walking on the prototype foot. During prosthetic push-off, amputees exhibited reduced energy transfer from the prosthesis to the COM along with increased hip work, perhaps due to greater energy dissipation at the knee. Nevertheless, the results indicate that spring compliance can contribute to push-off, but with biomechanical trade-offs that limit the degree to which greater push-off might improve walking economy. © 2011 IEEE

Systematic variation of prosthetic foot spring affects center-of-mass mechanics and metabolic cost during walking

PubMed Central

Zelik, Karl E.; Collins, Steven H.; Adamczyk, Peter G.; Segal, Ava D.; Klute, Glenn K.; Morgenroth, David C.; Hahn, Michael E.; Orendurff, Michael S.; Czerniecki, Joseph M.; Kuo, Arthur D.

2014-01-01

Lower-limb amputees expend more energy to walk than non-amputees and have an elevated risk of secondary disabilities. Insufficient push-off by the prosthetic foot may be a contributing factor. We aimed to systematically study the effect of prosthetic foot mechanics on gait, to gain insight into fundamental prosthetic design principles. We varied a single parameter in isolation, the energy-storing spring in a prototype prosthetic foot, the Controlled Energy Storage and Return (CESR) foot, and observed the effect on gait. Subjects walked on the CESR foot with three different springs. We performed parallel studies on amputees and on non-amputees wearing prosthetic simulators. In both groups, spring characteristics similarly affected ankle and body center-of-mass (COM) mechanics and metabolic cost. Softer springs led to greater energy storage, energy return and prosthetic limb COM push-off work. But metabolic energy expenditure was lowest with a spring of intermediate stiffness, suggesting biomechanical disadvantages to the softest spring despite its greater push-off. Disadvantages of the softest spring may include excessive heel displacements and COM collision losses. We also observed some differences in joint kinetics between amputees and non-amputees walking on the prototype foot. During prosthetic push-off, amputees exhibited reduced energy transfer from the prosthesis to the COM along with increased hip work, perhaps due to greater energy dissipation at the knee. Nevertheless, the results indicate that spring compliance can contribute to push-off, but with biomechanical trade-offs that limit the degree to which greater push-off might improve walking economy. PMID:21708509

Sorting Out Seasonal Allergies

MedlinePlus

... Dr. Georgeson. “Seasonal allergies—many times caused by pollen from trees, weeds and grasses—are triggered during ... or spring.” “For people with seasonal allergies, this pollen reacts with antibodies in the body, causing histamine ...

APPARATUS FOR GRINDING SPHERICAL BODIES

DOEpatents

Burch, R.F. Jr.

1963-09-24

A relatively inexpensive device is described for grinding rough ceramic bodies into accurate spherical shapes using a conventional drill press and a belt sander. A horizontal disk with an abrasive-surfaced recess in its lower face is mounted eccentrically on a vertical shaft which is forced downward against a stop by a spring. Bodies to be ground are placed in the recess and are subjected to the abrasive action of the belt sander as the disk is rotated by the drill press. (AEC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, Oden Lee; Asif, Syed Amanulla Syed; Oh, Yunje

A testing instrument for mechanical testing at nano or micron scale includes a transducer body, and a coupling shaft coupled with a probe tip. A transducer body houses a capacitor. The capacitor includes first and second counter electrodes and a center electrode assembly interposed therebetween. The center electrode assembly is movable with the coupling shaft relative to the first and second counter electrodes, for instance in one or more of dimensions including laterally and normally. The center electrode assembly includes a center plate coupled with the coupling shaft and one or more springs extending from the center plate. Upper andmore » lower plates are coupled with the center plate and cover the center plate and the one or more springs. A shaft support assembly includes one or more support elements coupled along the coupling shaft. The shaft support assembly provides lateral support to the coupling shaft.« less

Body size and hosts of Triatoma infestans populations affect the size of bloodmeal contents and female fecundity in rural northwestern Argentina

PubMed Central

Fernández, María del Pilar; Cecere, María Carla; Cohen, Joel E.

2017-01-01

Human sleeping quarters (domiciles) and chicken coops are key source habitats of Triatoma infestans—the principal vector of the infection that causes Chagas disease—in rural communities in northern Argentina. Here we investigated the links among individual bug bloodmeal contents (BMC, mg), female fecundity, body length (L, mm), host blood sources and habitats. We tested whether L, habitat and host blood conferred relative fitness advantages using generalized linear mixed-effects models and a multimodel inference approach with model averaging. The data analyzed include 769 late-stage triatomines collected in 120 sites from six habitats in 87 houses in Figueroa, Santiago del Estero, during austral spring. L correlated positively with other body-size surrogates and was modified by habitat type, bug stage and recent feeding. Bugs from chicken coops were significantly larger than pig-corral and kitchen bugs. The best-fitting model of log BMC included habitat, a recent feeding, bug stage, log Lc (mean-centered log L) and all two-way interactions including log Lc. Human- and chicken-fed bugs had significantly larger BMC than bugs fed on other hosts whereas goat-fed bugs ranked last, in consistency with average blood-feeding rates. Fecundity was maximal in chicken-fed bugs from chicken coops, submaximal in human- and pig-fed bugs, and minimal in goat-fed bugs. This study is the first to reveal the allometric effects of body-size surrogates on BMC and female fecundity in a large set of triatomine populations occupying multiple habitats, and discloses the links between body size, microsite temperatures and various fitness components that affect the risks of transmission of Trypanosoma cruzi. PMID:29211791

Body size and hosts of Triatoma infestans populations affect the size of bloodmeal contents and female fecundity in rural northwestern Argentina.

PubMed

Gürtler, Ricardo E; Fernández, María Del Pilar; Cecere, María Carla; Cohen, Joel E

2017-12-01

Human sleeping quarters (domiciles) and chicken coops are key source habitats of Triatoma infestans-the principal vector of the infection that causes Chagas disease-in rural communities in northern Argentina. Here we investigated the links among individual bug bloodmeal contents (BMC, mg), female fecundity, body length (L, mm), host blood sources and habitats. We tested whether L, habitat and host blood conferred relative fitness advantages using generalized linear mixed-effects models and a multimodel inference approach with model averaging. The data analyzed include 769 late-stage triatomines collected in 120 sites from six habitats in 87 houses in Figueroa, Santiago del Estero, during austral spring. L correlated positively with other body-size surrogates and was modified by habitat type, bug stage and recent feeding. Bugs from chicken coops were significantly larger than pig-corral and kitchen bugs. The best-fitting model of log BMC included habitat, a recent feeding, bug stage, log Lc (mean-centered log L) and all two-way interactions including log Lc. Human- and chicken-fed bugs had significantly larger BMC than bugs fed on other hosts whereas goat-fed bugs ranked last, in consistency with average blood-feeding rates. Fecundity was maximal in chicken-fed bugs from chicken coops, submaximal in human- and pig-fed bugs, and minimal in goat-fed bugs. This study is the first to reveal the allometric effects of body-size surrogates on BMC and female fecundity in a large set of triatomine populations occupying multiple habitats, and discloses the links between body size, microsite temperatures and various fitness components that affect the risks of transmission of Trypanosoma cruzi.

Parametric study of two-body floating-point wave absorber

NASA Astrophysics Data System (ADS)

Amiri, Atena; Panahi, Roozbeh; Radfar, Soheil

2016-03-01

In this paper, we present a comprehensive numerical simulation of a point wave absorber in deep water. Analyses are performed in both the frequency and time domains. The converter is a two-body floating-point absorber (FPA) with one degree of freedom in the heave direction. Its two parts are connected by a linear mass-spring-damper system. The commercial ANSYS-AQWA software used in this study performs well in considering validations. The velocity potential is obtained by assuming incompressible and irrotational flow. As such, we investigated the effects of wave characteristics on energy conversion and device efficiency, including wave height and wave period, as well as the device diameter, draft, geometry, and damping coefficient. To validate the model, we compared our numerical results with those from similar experiments. Our study results can clearly help to maximize the converter's efficiency when considering specific conditions.

Statistical Mechanics Model of Solids with Defects

NASA Astrophysics Data System (ADS)

Kaufman, M.; Walters, P. A.; Ferrante, J.

1997-03-01

Previously(M.Kaufman, J.Ferrante,NASA Tech. Memor.,1996), we examined the phase diagram for the failure of a solid under isotropic expansion and compression as a function of stress and temperature with the "springs" modelled by the universal binding energy relation (UBER)(J.H.Rose, J.R.Smith, F.Guinea, J.Ferrante, Phys.Rev.B29, 2963 (1984)). In the previous calculation we assumed that the "springs" failed independently and that the strain is uniform. In the present work, we have extended this statistical model of mechanical failure by allowing for correlations between "springs" and for thermal fluctuations in strains. The springs are now modelled in the harmonic approximation with a failure threshold energy E0, as an intermediate step in future studies to reinclude the full non-linear dependence of the UBER for modelling the interactions. We use the Migdal-Kadanoff renormalization-group method to determine the phase diagram of the model and to compute the free energy.

The impact of winter and spring temperatures on temperate tree budburst dates: results from an experimental climate manipulation.

PubMed

Fu, Yongshuo H; Campioli, Matteo; Deckmyn, Gaby; Janssens, Ivan A

2012-01-01

Budburst phenology is a key driver of ecosystem structure and functioning, and it is sensitive to global change. Both cold winter temperatures (chilling) and spring warming (forcing) are important for budburst. Future climate warming is expected to have a contrasting effect on chilling and forcing, and subsequently to have a non-linear effect on budburst timing. To clarify the different effects of warming during chilling and forcing phases of budburst phenology in deciduous trees, (i) we conducted a temperature manipulation experiment, with separate winter and spring warming treatments on well irrigated and fertilized saplings of beech, birch and oak, and (ii) we analyzed the observations with five temperature-based budburst models (Thermal Time model, Parallel model, Sequential model, Alternating model, and Unified model). The results show that both winter warming and spring warming significantly advanced budburst date, with the combination of winter plus spring warming accelerating budburst most. As expected, all three species were more sensitive to spring warming than to winter warming. Although the different chilling requirement, the warming sensitivity was not significantly different among the studied species. Model evaluation showed that both one- and two- phase models (without and with chilling, respectively) are able to accurately predict budburst. For beech, the Sequential model reproduced budburst dates best. For oak and birch, both Sequential model and the Thermal Time model yielded good fit with the data but the latter was slightly better in case of high parameter uncertainty. However, for late-flushing species, the Sequential model is likely be the most appropriate to predict budburst data in a future warmer climate.

Initial assessment of a multi-model approach to spring flood forecasting in Sweden

NASA Astrophysics Data System (ADS)

Olsson, J.; Uvo, C. B.; Foster, K.; Yang, W.

2015-06-01

Hydropower is a major energy source in Sweden and proper reservoir management prior to the spring flood onset is crucial for optimal production. This requires useful forecasts of the accumulated discharge in the spring flood period (i.e. the spring-flood volume, SFV). Today's SFV forecasts are generated using a model-based climatological ensemble approach, where time series of precipitation and temperature from historical years are used to force a calibrated and initialised set-up of the HBV model. In this study, a number of new approaches to spring flood forecasting, that reflect the latest developments with respect to analysis and modelling on seasonal time scales, are presented and evaluated. Three main approaches, represented by specific methods, are evaluated in SFV hindcasts for three main Swedish rivers over a 10-year period with lead times between 0 and 4 months. In the first approach, historically analogue years with respect to the climate in the period preceding the spring flood are identified and used to compose a reduced ensemble. In the second, seasonal meteorological ensemble forecasts are used to drive the HBV model over the spring flood period. In the third approach, statistical relationships between SFV and the large-sale atmospheric circulation are used to build forecast models. None of the new approaches consistently outperform the climatological ensemble approach, but for specific locations and lead times improvements of 20-30 % are found. When combining all forecasts in a weighted multi-model approach, a mean improvement over all locations and lead times of nearly 10 % was indicated. This demonstrates the potential of the approach and further development and optimisation into an operational system is ongoing.

Manufacture of conical springs with elastic medium technology improvement

NASA Astrophysics Data System (ADS)

Kurguzov, S. A.; Mikhailova, U. V.; Kalugina, O. B.

2018-01-01

This article considers the manufacturing technology improvement by using an elastic medium in the stamping tool forming space to improve the conical springs performance characteristics and reduce the costs of their production. Estimation technique of disk spring operational properties is developed by mathematical modeling of the compression process during the operation of a spring. A technique for optimizing the design parameters of a conical spring is developed, which ensures a minimum voltage value when operated in the edge of the spring opening.

A spring-block analogy for the dynamics of stock indexes

NASA Astrophysics Data System (ADS)

Sándor, Bulcsú; Néda, Zoltán

2015-06-01

A spring-block chain placed on a running conveyor belt is considered for modeling stylized facts observed in the dynamics of stock indexes. Individual stocks are modeled by the blocks, while the stock-stock correlations are introduced via simple elastic forces acting in the springs. The dragging effect of the moving belt corresponds to the expected economic growth. The spring-block system produces collective behavior and avalanche like phenomena, similar to the ones observed in stock markets. An artificial index is defined for the spring-block chain, and its dynamics is compared with the one measured for the Dow Jones Industrial Average. For certain parameter regions the model reproduces qualitatively well the dynamics of the logarithmic index, the logarithmic returns, the distribution of the logarithmic returns, the avalanche-size distribution and the distribution of the investment horizons. A noticeable success of the model is that it is able to account for the gain-loss asymmetry observed in the inverse statistics. Our approach has mainly a pedagogical value, bridging between a complex socio-economic phenomena and a basic (mechanical) model in physics.

Interaction of part-through cracks in a flat plate

NASA Technical Reports Server (NTRS)

Aksel, B.; Erdogan, F.

1985-01-01

The accuracy of the line spring model is determined. The effect of interaction between two and three cracks is investigated, and extensive numerical results which may be useful in applications are provided. Line spring model with Reissner's plate theory is formulated to be used for any number and configurations of cracks provided that there is symmetry. This model is used to find stress intensity factors for elliptic internal cracks, elliptic edge cracks and two opposite elliptic edge cracks. Despite the simplicity of the line spring model, the results are found to be close.

Slip-Size Distribution and Self-Organized Criticality in Block-Spring Models with Quenched Randomness

NASA Astrophysics Data System (ADS)

Sakaguchi, Hidetsugu; Kadowaki, Shuntaro

2017-07-01

We study slowly pulling block-spring models in random media. Second-order phase transitions exist in a model pulled by a constant force in the case of velocity-strengthening friction. If external forces are slowly increased, nearly critical states are self-organized. Slips of various sizes occur, and the probability distributions of slip size roughly obey power laws. The exponent is close to that in the quenched Edwards-Wilkinson model. Furthermore, the slip-size distributions are investigated in cases of Coulomb friction, velocity-weakening friction, and two-dimensional block-spring models.

Application of Computer Technologies in Building Design by Example of Original Objects of Increased Complexity

NASA Astrophysics Data System (ADS)

Vasilieva, V. N.

2017-11-01

The article deals with the solution of problems in AutoCAD offered at the All-Russian student Olympiads at the section of “Computer graphics” that are not typical for the students of construction specialties. The students are provided with the opportunity to study the algorithm for solving original tasks of high complexity. The article shows how the unknown parameter underlying the construction can be determined using a parametric drawing with geometric constraints and dimensional dependencies. To optimize the mark-up operation, the use of the command for projecting the points and lines of different types onto bodies and surfaces in different directions is shown. For the construction of a spring with a different pitch of turns, the paper describes the creation of a block from a part of the helix and its scaling when inserted into a model with unequal coefficients along the axes. The advantage of the NURBS surface and the application of the “body-surface-surface-NURBS-body” conversion are reflected to enhance the capabilities of both solid and surface modeling. The article’s material introduces construction students into the method of constructing complex models in AutoCAD that are not similar to typical training assignments.

A new seasonal-deciduous spring phenology submodel in the Community Land Model 4.5: impacts on carbon and water cycling under future climate scenarios.

PubMed

Chen, Min; Melaas, Eli K; Gray, Josh M; Friedl, Mark A; Richardson, Andrew D

2016-11-01

A spring phenology model that combines photoperiod with accumulated heating and chilling to predict spring leaf-out dates is optimized using PhenoCam observations and coupled into the Community Land Model (CLM) 4.5. In head-to-head comparison (using satellite data from 2003 to 2013 for validation) for model grid cells over the Northern Hemisphere deciduous broadleaf forests (5.5 million km 2 ), we found that the revised model substantially outperformed the standard CLM seasonal-deciduous spring phenology submodel at both coarse (0.9 × 1.25°) and fine (1 km) scales. The revised model also does a better job of representing recent (decadal) phenological trends observed globally by MODIS, as well as long-term trends (1950-2014) in the PEP725 European phenology dataset. Moreover, forward model runs suggested a stronger advancement (up to 11 days) of spring leaf-out by the end of the 21st century for the revised model. Trends toward earlier advancement are predicted for deciduous forests across the whole Northern Hemisphere boreal and temperate deciduous forest region for the revised model, whereas the standard model predicts earlier leaf-out in colder regions, but later leaf-out in warmer regions, and no trend globally. The earlier spring leaf-out predicted by the revised model resulted in enhanced gross primary production (up to 0.6 Pg C yr -1 ) and evapotranspiration (up to 24 mm yr -1 ) when results were integrated across the study region. These results suggest that the standard seasonal-deciduous submodel in CLM should be reconsidered, otherwise substantial errors in predictions of key land-atmosphere interactions and feedbacks may result. © 2016 John Wiley & Sons Ltd.

Mixing of shallow and deep groundwater as indicated by the chemistry and age of karstic springs

USGS Publications Warehouse

Toth, D.J.; Katz, B.G.

2006-01-01

Large karstic springs in east-central Florida, USA were studied using multi-tracer and geochemical modeling techniques to better understand groundwater flow paths and mixing of shallow and deep groundwater. Spring water types included Ca-HCO3 (six), Na-Cl (four), and mixed (one). The evolution of water chemistry for Ca-HCO3 spring waters was modeled by reactions of rainwater with soil organic matter, calcite, and dolomite under oxic conditions. The Na-Cl and mixed-type springs were modeled by reactions of either rainwater or Upper Floridan aquifer water with soil organic matter, calcite, and dolomite under oxic conditions and mixed with varying proportions of saline Lower Floridan aquifer water, which represented 4-53% of the total spring discharge. Multiple-tracer data-chlorofluorocarbon CFC-113, tritium (3H), helium-3 (3Hetrit), sulfur hexafluoride (SF6) - for four Ca-HCO3 spring waters were consistent with binary mixing curves representing water recharged during 1980 or 1990 mixing with an older (recharged before 1940) tracer-free component. Young-water mixing fractions ranged from 0.3 to 0.7. Tracer concentration data for two Na-Cl spring waters appear to be consistent with binary mixtures of 1990 water with older water recharged in 1965 or 1975. Nitrate-N concentrations are inversely related to apparent ages of spring waters, which indicated that elevated nitrate-N concentrations were likely contributed from recent recharge. ?? Springer-Verlag 2006.

Erratum: Mixing of shallow and deep groundwater as indicated by the chemistry and age of karstic springs

NASA Astrophysics Data System (ADS)

Toth, David J.; Katz, Brian G.

2006-09-01

Large karstic springs in east-central Florida, USA were studied using multi-tracer and geochemical modeling techniques to better understand groundwater flow paths and mixing of shallow and deep groundwater. Spring water types included Ca-HCO3 (six), Na-Cl (four), and mixed (one). The evolution of water chemistry for Ca-HCO3 spring waters was modeled by reactions of rainwater with soil organic matter, calcite, and dolomite under oxic conditions. The Na-Cl and mixed-type springs were modeled by reactions of either rainwater or Upper Floridan aquifer water with soil organic matter, calcite, and dolomite under oxic conditions and mixed with varying proportions of saline Lower Floridan aquifer water, which represented 4-53% of the total spring discharge. Multiple-tracer data—chlorofluorocarbon CFC-113, tritium (3H), helium-3 (3Hetrit), sulfur hexafluoride (SF6)—for four Ca-HCO3 spring waters were consistent with binary mixing curves representing water recharged during 1980 or 1990 mixing with an older (recharged before 1940) tracer-free component. Young-water mixing fractions ranged from 0.3 to 0.7. Tracer concentration data for two Na-Cl spring waters appear to be consistent with binary mixtures of 1990 water with older water recharged in 1965 or 1975. Nitrate-N concentrations are inversely related to apparent ages of spring waters, which indicated that elevated nitrate-N concentrations were likely contributed from recent recharge.

Water quality modelling of Jadro spring.

PubMed

Margeta, J; Fistanic, I

2004-01-01

Management of water quality in karst is a specific problem. Water generally moves very fast by infiltration processes but far more by concentrated flows through fissures and openings in karst. This enables the entire surface pollution to be transferred fast and without filtration into groundwater springs. A typical example is the Jadro spring. Changes in water quality at the spring are sudden, but short. Turbidity as a major water quality problem for the karst springs regularly exceeds allowable standards. Former practice in problem solving has been reduced to intensive water disinfection in periods of great turbidity without analyses of disinfection by-products risks for water users. The main prerequisite for water quality control and an optimization of water disinfection is the knowledge of raw water quality and nature of occurrence. The analysis of monitoring data and their functional relationship with hydrological parameters enables establishment of a stochastic model that will help obtain better information on turbidity in different periods of the year. Using the model a great number of average monthly and extreme daily values are generated. By statistical analyses of these data possibility of occurrence of high turbidity in certain months is obtained. This information can be used for designing expert system for water quality management of karst springs. Thus, the time series model becomes a valuable tool in management of drinking water quality of the Jadro spring.

Analysis of Dynamic Stiffness Effect of Primary Suspension Helical Springs on Railway Vehicle Vibration

NASA Astrophysics Data System (ADS)

Sun, W.; Thompson, D. J.; Zhou, J.; Gong, D.

2016-09-01

Helical springs within the primary suspension are critical components for isolating the whole vehicle system from vibration generated at the wheel/rail contact. As train speeds increase, the frequency region of excitation becomes larger, and a simplified static stiffness can no longer represent the real stiffness property in a vehicle dynamic model. Coil springs in particular exhibit strong internal resonances, which lead to high vibration amplitudes within the spring itself as well as degradation of the vibration isolation. In this paper, the dynamic stiffness matrix method is used to determine the dynamic stiffness of a helical spring from a vehicle primary suspension. Results are confirmed with a finite element analysis. Then the spring dynamic stiffness is included within a vehicle-track coupled dynamic model of a high speed train and the effect of the dynamic stiffening of the spring on the vehicle vibration is investigated. It is shown that, for frequencies above about 50 Hz, the dynamic stiffness of the helical spring changes sharply. Due to this effect, the vibration transmissibility increases considerably which results in poor vibration isolation of the primary suspension. Introducing a rubber layer in series with the coil spring can attenuate this effect.

KSC-03pd0515

NASA Image and Video Library

2003-02-19

KENNEDY SPACE CENTER, FLA. -- In a demonstration of the agility of the Mars Exploration Rover, a model of the Rover rolls over the prone bodies of two volunteer students during NASA's Family & Community Mars Exploration Day held in Cape Canaveral, Fla. The event informed students and the general public about Florida's key role as NASA's "Gateway to Mars" and offered an opportunity to meet with scientists, engineers, educators and others working Mars exploration missions. The Mars Exploration Rovers are being prepared for launch this spring aboard Boeing Delta II rockets from the Cape Canaveral Air Force Station. They will land on Mars and start exploring in January 2004.

KSC-03PD-0515

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. -- In a demonstration of the agility of the Mars Exploration Rover, a model of the Rover rolls over the prone bodies of two volunteer students during NASA's Family & Community Mars Exploration Day held in Cape Canaveral, Fla. The event informed students and the general public about Florida's key role as NASA's 'Gateway to Mars' and offered an opportunity to meet with scientists, engineers, educators and others working Mars exploration missions. The Mars Exploration Rovers are being prepared for launch this spring aboard Boeing Delta II rockets from the Cape Canaveral Air Force Station. They will land on Mars and start exploring in January 2004.

Spring-back simulation of unidirectional carbon/epoxy L- shaped laminate composites manufactured through autoclave processing

NASA Astrophysics Data System (ADS)

Nasir, M. N. M.; Mezeix, L.; Aminanda, Y.; Seman, M. A.; Rivai, A.; Ali, K. M.

2016-02-01

This paper presents an original method in predicting the spring-back for composite aircraft structures using non-linear Finite Element Analysis (FEA) and is an extension of the previous accompanying study on flat geometry samples. Firstly, unidirectional prepreg lay-up samples are fabricated on moulds with different corner angles (30°, 45° and 90°) and the effect on spring-back deformation are observed. Then, the FEA model that was developed in the previous study on flat samples is utilized. The model maintains the physical mechanisms of spring-back such as ply stretching and tool-part interface properties with the additional mechanism in the corner effect and geometrical changes in the tool, part and the tool-part interface components. The comparative study between the experimental data and FEA results show that the FEA model predicts adequately the spring-back deformation within the range of corner angle tested.

Lethal and sublethal effects, and incomplete clearance of ingested imidacloprid in honey bees (Apis mellifera).

PubMed

Sánchez-Bayo, Francisco; Belzunces, Luc; Bonmatin, Jean-Marc

2017-11-01

A previous study claimed a differential behavioural resilience between spring or summer honey bees (Apis mellifera) and bumble bees (Bombus terrestris) after exposure to syrup contaminated with 125 µg L -1 imidacloprid for 8 days. The authors of that study based their assertion on the lack of body residues and toxic effects in honey bees, whereas bumble bees showed body residues of imidacloprid and impaired locomotion during the exposure. We have reproduced their experiment using winter honey bees subject to the same protocol. After exposure to syrup contaminated with 125 µg L -1 imidacloprid, honey bees experienced high mortality rates (up to 45%), had body residues of imidacloprid in the range 2.7-5.7 ng g -1 and exhibited abnormal behaviours (restless, apathetic, trembling and falling over) that were significantly different from the controls. There was incomplete clearance of the insecticide during the 10-day exposure period. Our results contrast with the findings reported in the previous study for spring or summer honey bees, but are consistent with the results reported for the other bee species.

[Protein content in urine of male and female water vole (Arvicola amphibious) at the period of spring growth and sexual maturation].

PubMed

Nazarova, G G; Proskurniak, L P

2012-01-01

The study was carried out on the captive bread water voles Arvicola amphibious kept in vivarium. At the first decade of January, March, and June, the body length and anogenital distance were measured, the body mass was determined, and urine was collected for determination of its protein content. The obtained results have shown that the protein content depends on sex of the animals and is connected with the reproductive status of males and their dimension-weight characteristics. The urinary protein excretion level in females remained stable at different months, whereas in males its sharp rise was noted at the period of spring growth and sexual maturation. The significant sexual differences were established in March and enhanced in June. In March the urine protein content in males was noted to correlate positively with the body mass and length and with the anogenital distance. The males reached sexual maturity at the earlier calendar terms than the females did; in sexually mature males the urine protein content was significantly higher than in the sexually immature ones.

Optimal design and control of an electromechanical transfemoral prosthesis with energy regeneration.

PubMed

Rohani, Farbod; Richter, Hanz; van den Bogert, Antonie J

2017-01-01

In this paper, we present the design of an electromechanical above-knee active prosthesis with energy storage and regeneration. The system consists of geared knee and ankle motors, parallel springs for each motor, an ultracapacitor, and controllable four-quadrant power converters. The goal is to maximize the performance of the system by finding optimal controls and design parameters. A model of the system dynamics was developed, and used to solve a combined trajectory and design optimization problem. The objectives of the optimization were to minimize tracking error relative to human joint motions, as well as energy use. The optimization problem was solved by the method of direct collocation, based on joint torque and joint angle data from ten subjects walking at three speeds. After optimization of controls and design parameters, the simulated system could operate at zero energy cost while still closely emulating able-bodied gait. This was achieved by controlled energy transfer between knee and ankle, and by controlled storage and release of energy throughout the gait cycle. Optimal gear ratios and spring parameters were similar across subjects and walking speeds.

Simulating the onset of spring vegetation growth across the Northern Hemisphere.

PubMed

Liu, Qiang; Fu, Yongshuo H; Liu, Yongwen; Janssens, Ivan A; Piao, Shilong

2018-03-01

Changes in the spring onset of vegetation growth in response to climate change can profoundly impact climate-biosphere interactions. Thus, robust simulation of spring onset is essential to accurately predict ecosystem responses and feedback to ongoing climate change. To date, the ability of vegetation phenology models to reproduce spatiotemporal patterns of spring onset at larger scales has not been thoroughly investigated. In this study, we took advantage of phenology observations via remote sensing to calibrate and evaluated six models, including both one-phase (considering only forcing temperatures) and two-phase (involving forcing, chilling, and photoperiod) models across the Northern Hemisphere between 1982 and 2012. Overall, we found that the model that integrated the photoperiod effect performed best at capturing spatiotemporal patterns of spring phenology in boreal and temperate forests. By contrast, all of the models performed poorly in simulating the onset of growth in grasslands. These results suggest that the photoperiod plays a role in controlling the onset of growth in most Northern Hemisphere forests, whereas other environmental factors (e.g., precipitation) should be considered when simulating the onset of growth in grasslands. We also found that the one-phase model performed as well as the two-phase models in boreal forests, which implies that the chilling requirement is probably fulfilled across most of the boreal zone. Conversely, two-phase models performed better in temperate forests than the one-phase model, suggesting that photoperiod and chilling play important roles in these temperate forests. Our results highlight the significance of including chilling and photoperiod effects in models of the spring onset of forest growth at large scales, and indicate that the consideration of additional drivers may be required for grasslands. © 2017 John Wiley & Sons Ltd.

The resolved nucleus of Comet Siding Spring (C/2013 A1) in MRO HiRISE images

NASA Astrophysics Data System (ADS)

Farnham, Tony; Kelley, Michael S.; Bodewits, Dennis; Bauer, James M.

2017-10-01

Comet Siding Spring (C/2013 A1) passed within 140,000 km of Mars on 19 Oct 2014. The MRO spacecraft, in orbit around Mars, used its HiRISE camera to monitor the comet during the encounter, obtaining the first resolved images of the nucleus of a dynamically new comet.MRO observed Siding Spring from 60 hr before, to 15 hr after close approach, obtaining 122 images in three different color filters. Close approach images, with a spatial scale as small as 138 m/pix, reveal an elongated crescent that changes shape over the course of the sequence, indicating that we are seeing a ~1 km non-spherical body from different viewpoints as the comet rapidly sweeps past. To better constrain the characteristics of the nucleus, we are performing detailed analyses, including modeling of the inner coma to separate its flux contribution from that of the nucleus. In conjunction with the coma removal, we will model the nucleus as a prolate/triaxial ellipsoid and, combined with the known illumination and viewing conditions, will use the changing aspect in the images to constrain the size, shape, orientation, albedo and possibly the phase dependence of the nucleus.In addition to the close approach observations, the images before and after close approach capture the coma structure and brightness. The photometric lightcurve from these images shows variability with an 8.1 hr period, which is presumed to be the rotational modulation of the coma activity. The observed morphology changes as well, promising to provide a measure of the nucleus' spin axis orientation.We will report on the results from our analyses, and provide the first direct measurements of the nucleus of a dynamically new comet.

CACTUS SPRING ROADLESS AREA, CALIFORNIA.

USGS Publications Warehouse

Matti, Jonathan C.; Kuizon, Lucia

1984-01-01

Geologic, geochemical, and geophysical studies together with a review of historic mining and prospecting activities indicate that the Cactus Spring Roadless Area in California has little promise for the occurrence of mineral or energy resources. Marble bodies occur in the northern part of the roadless area and are possible resources for building stone, crushed and quarried aggregate, and lime and magnesium for Portland cement and industrial applications. It is recommended that the terrane of marble be mapped and sampled carefully in order to evaluate the quantity and quality of the carbonate resources.

Process-based monitoring and modeling of Karst springs - Linking intrinsic to specific vulnerability.

PubMed

Epting, Jannis; Page, Rebecca M; Auckenthaler, Adrian; Huggenberger, Peter

2018-06-01

The presented work illustrates to what extent field investigations as well as monitoring and modeling approaches are necessary to understand the high discharge dynamics and vulnerability of Karst springs. In complex settings the application of 3D geological models is essential for evaluating the vulnerability of Karst systems. They allow deriving information on catchment characteristics, as the geometry of aquifers and aquitards as well as their displacements along faults. A series of Karst springs in northwestern Switzerland were compared and Karst system dynamics with respect to qualitative and quantitative issues were evaluated. The main objective of the studies was to combine information of catchment characteristics and data from novel monitoring systems (physicochemical and microbiological parameters) to assess the intrinsic vulnerability of Karst springs to microbiological contamination with simulated spring discharges derived from numerical modeling (linear storage models). The numerically derived relation of fast and slow groundwater flow components enabled us to relate different sources of groundwater recharge and to characterize the dynamics of the Karst springs. Our study illustrates that comparably simple model-setups were able to reproduce the overall dynamic intrinsic vulnerability of several Karst systems and that one of the most important processes involved was the temporal variation of groundwater recharge (precipitation, evapotranspiration and snow melt). Furthermore, we make a first attempt on how to link intrinsic to specific vulnerability of Karst springs, which involves activities within the catchment area as human impacts from agriculture and settlements. Likewise, by a more detailed representation of system dynamics the influence of surface water, which is impacted by release events from storm sewers, infiltrating into the Karst system, could be considered. Overall, we demonstrate that our approach can be the basis for a more flexible and differentiated management and monitoring of raw-water quality of Karst springs. Copyright © 2017 Elsevier B.V. All rights reserved.

Continuum vs. spring network models of airway-parenchymal interdependence

PubMed Central

Ma, Baoshun

2012-01-01

The outward tethering forces exerted by the lung parenchyma on the airways embedded within it are potent modulators of the ability of the airway smooth muscle to shorten. Much of our understanding of these tethering forces is based on treating the parenchyma as an elastic continuum; yet, on a small enough scale, the lung parenchyma in two dimensions would seem to be more appropriately described as a discrete spring network. We therefore compared how the forces and displacements in the parenchyma surrounding a contracting airway are predicted to differ depending on whether the parenchyma is modeled as an elastic continuum or as a spring network. When the springs were arranged hexagonally to represent alveolar walls, the predicted parenchymal stresses and displacements propagated substantially farther away from the airway than when the springs were arranged in a triangular pattern or when the parenchyma was modeled as a continuum. Thus, to the extent that the parenchyma in vivo behaves as a hexagonal spring network, our results suggest that the range of interdependence forces due to airway contraction may have a greater influence than was previously thought. PMID:22500006

Parsimonious Hydrologic and Nitrate Response Models For Silver Springs, Florida

NASA Astrophysics Data System (ADS)

Klammler, Harald; Yaquian-Luna, Jose Antonio; Jawitz, James W.; Annable, Michael D.; Hatfield, Kirk

2014-05-01

Silver Springs with an approximate discharge of 25 m3/sec is one of Florida's first magnitude springs and among the largest springs worldwide. Its 2500-km2 springshed overlies the mostly unconfined Upper Floridan Aquifer. The aquifer is approximately 100 m thick and predominantly consists of porous, fractured and cavernous limestone, which leads to excellent surface drainage properties (no major stream network other than Silver Springs run) and complex groundwater flow patterns through both rock matrix and fast conduits. Over the past few decades, discharge from Silver Springs has been observed to slowly but continuously decline, while nitrate concentrations in the spring water have enormously increased from a background level of 0.05 mg/l to over 1 mg/l. In combination with concurrent increases in algae growth and turbidity, for example, and despite an otherwise relatively stable water quality, this has given rise to concerns about the ecological equilibrium in and near the spring run as well as possible impacts on tourism. The purpose of the present work is to elaborate parsimonious lumped parameter models that may be used by resource managers for evaluating the springshed's hydrologic and nitrate transport responses. Instead of attempting to explicitly consider the complex hydrogeologic features of the aquifer in a typically numerical and / or stochastic approach, we use a transfer function approach wherein input signals (i.e., time series of groundwater recharge and nitrate loading) are transformed into output signals (i.e., time series of spring discharge and spring nitrate concentrations) by some linear and time-invariant law. The dynamic response types and parameters are inferred from comparing input and output time series in frequency domain (e.g., after Fourier transformation). Results are converted into impulse (or step) response functions, which describe at what time and to what magnitude a unitary change in input manifests at the output. For the hydrologic response model, frequency spectra of groundwater recharge and spring discharge suggest an exponential response model, which may explain a significant portion of spring discharge variability with only two fitting parameters (mean response time 2.4 years). For the transport model, direct use of nitrate data is confounded by inconsistent data and a strong trend. Instead, chloride concentrations in rainfall and at the spring are investigated as a surrogate candidate. Preliminary results indicate that the transport response function of the springshed as a whole may be of the gamma type, which possesses both a larger initial peak as well as a longer tail than the exponential response function. This is consistent with the large range of travel times to be expected between input directly into fast conduits connected to the spring (e.g., though sinkholes) and input or back-diffusion from the rock matrix. The result implies that reductions in nitrate input, especially at remote and hydraulically not well connected locations, will only manifest in a rather delayed and smoothed out form in concentration observed at the spring.

Digital data sets that describe aquifer characteristics of the Rush Springs Aquifer in western Oklahoma

USGS Publications Warehouse

Runkle, D.L.; Becker, M.F.; Rea, Alan

1997-01-01

This diskette contains digitized aquifer boundaries and maps of hydraulic conductivity, recharge, and ground-water level elevation contours for the Rush Spring aquifer in western Oklahoma. This area encompasses all or part of Blaine, Caddo, Canadian, Comanche, Custer, Dewey, Grady, Stephens, and Washita Counties. These digital data sets were developed by Mark F. Becker to use as input into a computer model that simulated ground-water flow in the Rush Springs aquifer (Mark F. Becker, U.S. Geological Survey, written commun., 1997). For the purposes of modeling the ground-water flow in the Rush Springs aquifer, Mark F. Becker (written commun., 1997) defined the Rush Springs aquifer to include the Rush Springs Formation, alluvial and terrace deposits along major streams, and parts of the Marlow Formations, particularly in the eastern part of the aquifer boundary area. The Permian-age Rush Springs Formation consists of highly cross-bedded sandstone with some interbedded dolomite and gypsum. The Rush Springs Formation is overlain by Quaternary-age alluvial and terrace deposits that consist of unconsolidated clay, silt, sand, and gravel. The Rush Springs Formation is underlain by the Permian-age Marlow Formation that consists of interbedded sandstones, siltstones, mudstones, gypsum-anhydrite, and dolomite beds (Mark F. Becker, written commun., 1997). The parts of the Marlow Formation that have high permeability and porosity are where the Marlow Formation is included as part of the Rush Springs aquifer. The Rush Springs aquifer underlies about 2,400 square miles of western Oklahoma and is an important source of water for irrigation, livestock, industrial, municipal, and domestic use. Irrigation wells are reported to have well yields greater than 1,000 gallons per minute (Mark F. Becker, written commun., 1997). Mark F. Becker created some of the aquifer boundaries, hydraulic conductivity, and recharge data sets by digitizing parts of previously published surficial geology maps. The hydraulic conductivity and recharge values are the input data to the ground-water flow model (Mark F. Becker, written commun., 1997). The water-level elevation data set was prepared at a scale of 1:250,000 by Mark F. Becker (written commun., 1997) from water levels measured in wells prior to the year 1950. Ground-water flow models are numerical representations that simplify and aggregate natural systems. Models are not unique; different combinations of aquifer characteristics may produce similar results. Therefore, values of hydraulic conductivity and recharge used in the model and presented in this data set are not precise, but are within a reasonable range when compared to independently collected data.

Spring assisted cranioplasty: A patient specific computational model.

PubMed

Borghi, Alessandro; Rodriguez-Florez, Naiara; Rodgers, Will; James, Gregory; Hayward, Richard; Dunaway, David; Jeelani, Owase; Schievano, Silvia

2018-03-01

Implantation of spring-like distractors in the treatment of sagittal craniosynostosis is a novel technique that has proven functionally and aesthetically effective in correcting skull deformities; however, final shape outcomes remain moderately unpredictable due to an incomplete understanding of the skull-distractor interaction. The aim of this study was to create a patient specific computational model of spring assisted cranioplasty (SAC) that can help predict the individual overall final head shape. Pre-operative computed tomography images of a SAC patient were processed to extract a 3D model of the infant skull anatomy and simulate spring implantation. The distractors were modeled based on mechanical experimental data. Viscoelastic bone properties from the literature were tuned using the specific patient procedural information recorded during surgery and from x-ray measurements at follow-up. The model accurately captured spring expansion on-table (within 9% of the measured values), as well as at first and second follow-ups (within 8% of the measured values). Comparison between immediate post-operative 3D head scanning and numerical results for this patient proved that the model could successfully predict the final overall head shape. This preliminary work showed the potential application of computational modeling to study SAC, to support pre-operative planning and guide novel distractor design. Copyright © 2018 IPEM. Published by Elsevier Ltd. All rights reserved.

On the accuracy of modelling the dynamics of large space structures

NASA Technical Reports Server (NTRS)

Diarra, C. M.; Bainum, P. M.

1985-01-01

Proposed space missions will require large scale, light weight, space based structural systems. Large space structure technology (LSST) systems will have to accommodate (among others): ocean data systems; electronic mail systems; large multibeam antenna systems; and, space based solar power systems. The structures are to be delivered into orbit by the space shuttle. Because of their inherent size, modelling techniques and scaling algorithms must be developed so that system performance can be predicted accurately prior to launch and assembly. When the size and weight-to-area ratio of proposed LSST systems dictate that the entire system be considered flexible, there are two basic modeling methods which can be used. The first is a continuum approach, a mathematical formulation for predicting the motion of a general orbiting flexible body, in which elastic deformations are considered small compared with characteristic body dimensions. This approach is based on an a priori knowledge of the frequencies and shape functions of all modes included within the system model. Alternatively, finite element techniques can be used to model the entire structure as a system of lumped masses connected by a series of (restoring) springs and possibly dampers. In addition, a computational algorithm was developed to evaluate the coefficients of the various coupling terms in the equations of motion as applied to the finite element model of the Hoop/Column.

Interspecific resource partitioning in sympatric ursids

USGS Publications Warehouse

Belant, Jerrold L.; Kielland, Knut; Follmann, Erich H.; Adams, Layne G.

2006-01-01

The fundamental niche of a species is rarely if ever realized because the presence of other species restricts it to a narrower range of ecological conditions. The effects of this narrower range of conditions define how resources are partitioned. Resource partitioning has been inferred but not demonstrated previously for sympatric ursids. We estimated assimilated diet in relation to body condition (body fat and lean and total body mass) and reproduction for sympatric brown bears (Ursus arctos) and American black bears (U. americanus) in south‐central Alaska, 1998–2000. Based on isotopic analysis of blood and keratin in claws, salmon (Oncorhynchus spp.) predominated in brown bear diets (>53% annually) whereas black bears assimilated 0–25% salmon annually. Black bears did not exploit salmon during a year with below average spawning numbers, probably because brown bears deterred black bear access to salmon. Proportion of salmon in assimilated diet was consistent across years for brown bears and represented the major portion of their diet. Body size of brown bears in the study area approached mean body size of several coastal brown bear populations, demonstrating the importance of salmon availability to body condition. Black bears occurred at a comparable density (mass : mass), but body condition varied and was related directly to the amount of salmon assimilated in their diet. Both species gained most lean body mass during spring and all body fat during summer when salmon were present. Improved body condition (i.e., increased percentage body fat) from salmon consumption reduced catabolism of lean body mass during hibernation, resulting in better body condition the following spring. Further, black bear reproduction was directly related to body condition; reproductive rates were reduced when body condition was lower. High body fat content across years for brown bears was reflected in consistently high reproductive levels. We suggest that the fundamental niche of black bears was constrained by brown bears through partitioning of food resources, which varied among years. Reduced exploitation of salmon caused black bears to rely more extensively on less reliable or nutritious food sources (e.g., moose [Alces alces], berries) resulting in lowered body condition and subsequent reproduction.

Age-class differences in the pattern of hibernation in yellow-bellied marmots, Marmota flaviventris.

PubMed

French, A R

1990-01-01

Age-related differences in the patterns of body temperature regulation during hibernation were found in yellow-bellied marmots. The timing of all entrances into and arousals from torpor was determined from continuous records of thermocouples mounted in each animal's nest box. Older marmots spent more time at high body temperatures following periodic arousals from torpor than did juveniles undergoing their first season of hibernation. In addition, older marmots spontaneously terminated their hibernation seasons in the spring, whereas most juveniles continued to hibernate until either they were emaciated from starvation or they were fed. These two patterns of hibernation reflect age- and size-related differences in the degree to which the animals are constrained energetically and the probability that they can successfully reproduce in spring. The patterns also are consistent with age-related differences in the timing of dormancy in nature.

Experimental Investigation of a Preloaded Spring-tab Flutter Model

NASA Technical Reports Server (NTRS)

Smith, N H; Clevenson, S A; Barmby, J G

1947-01-01

An experimental investigation was made of a preloaded spring-tab flutter model to determine the effects on flutter speed of aspect ratio, tab frequency, and preloaded spring constant. The rudder was mass-balanced, and the flutter mode studied was essentially one of three degrees of freedom (fin bending coupled with rudder and tab oscillations). Inasmuch as the spring was preloaded, the tab-spring system was a nonlinear one. Frequency of the tab was the most significant parameter in this study, and an increase in flutter speed with increasing frequency is indicated. At a given frequency, the tab of high aspect ratio is shown to have a slightly lower flutter speed than the one of low aspect ratio. Because the frequency of the preloaded spring tab was found to vary radically with amplitude, the flutter speed decreased with increase in initial displacement of the tab.

Based on Artificial Neural Network to Realize K-Parameter Analysis of Vehicle Air Spring System

NASA Astrophysics Data System (ADS)

Hung, San-Shan; Hsu, Chia-Ning; Hwang, Chang-Chou; Chen, Wen-Jan

2017-10-01

In recent years, because of the air-spring control technique is more mature, that air- spring suspension systems already can be used to replace the classical vehicle suspension system. Depend on internal pressure variation of the air-spring, thestiffnessand the damping factor can be adjusted. Because of air-spring has highly nonlinear characteristic, therefore it isn’t easy to construct the classical controller to control the air-spring effectively. The paper based on Artificial Neural Network to propose a feasible control strategy. By using offline way for the neural network design and learning to the air-spring in different initial pressures and different loads, offline method through, predict air-spring stiffness parameter to establish a model. Finally, through adjusting air-spring internal pressure to change the K-parameter of the air-spring, realize the well dynamic control performance of air-spring suspension.

Combined electromagnetic geophysical mapping at Arctic perennial saline springs: Possible applications for the detection of water in the shallow subsurface of Mars

NASA Astrophysics Data System (ADS)

Samson, C.; Mah, J.; Haltigin, T.; Holladay, S.; Ralchenko, M.; Pollard, W.; Monteiro Santos, F. A.

2017-05-01

Perennial springs at the Gypsum Hill site on Axel Heiberg Island in the Canadian Arctic (79°24‧N, 90°44‧W) represent a high-fidelity analogue to hydrothermal systems that might exist on Mars. The springs were surveyed using an electromagnetic induction sounder (EMIS) and ground penetrating radar (GPR). Both instruments probed the subsurface to a depth of approximately 3 m. Lateral EMIS soundings were performed every metre along a 400 m long reconnaissance line roughly oriented SW-NE and extending through 23 active springs and 1 dry outlet to measure electrical conductivity. Two distinct zones were identified within the survey area on the basis of these data: in the southwest portion, sharp conductivity peaks correspond to isolated springs with well-defined outlets, flowing over dry rocky soil; in the northeast portion, the springs are fed by a pervasive network of saline fluids, resulting in high background readings and muddy surface conditions. These observations are consistent with vertical EMIS sounding data which showed that the brine body feeding the saline springs can be found closer to the ground surface towards the northeast portion of the survey site. In areas of high electrical conductivity, the GPR data exhibits strong scattering. The noisy areas are sharply defined and interpreted to correspond to narrow vertical conduits feeding individual spring outlets. The EMIS is a rugged instrument that could be included as payload in future rover-based Mars exploration missions aiming at probing the shallow subsurface for the presence of brine pockets.

The measured contribution of whipping and springing on the fatigue and extreme loading of container vessels

NASA Astrophysics Data System (ADS)

Storhaug, Gaute

2014-12-01

Whipping/springing research started in the 50'ies. In the 60'ies inland water vessels design rules became stricter due to whipping/springing. The research during the 70-90'ies may be regarded as academic. In 2000 a large ore carrier was strengthened due to severe cracking from North Atlantic operation, and whipping/springing contributed to half of the fatigue damage. Measurement campaigns on blunt and slender vessels were initiated. A few blunt ships were designed to account for whipping/springing. Based on the measurements, the focus shifted from fatigue to extreme loading. In 2005 model tests of a 4,400 TEU container vessel included extreme whipping scenarios. In 2007 the 4400 TEU vessel MSC Napoli broke in two under similar conditions. In 2009 model tests of an 8,600 TEU container vessel container vessel included extreme whipping scenarios. In 2013 the 8,100 TEU vessel MOL COMFORT broke in two under similar conditions. Several classification societies have published voluntary guidelines, which have been used to include whipping/springing in the design of several container vessels. This paper covers results from model tests and full scale measurements used as background for the DNV Legacy guideline. Uncertainties are discussed and recommendations are given in order to obtain useful data. Whipping/springing is no longer academic.

Firework injuries at a major trauma and burn center: A five-year prospective study.

PubMed

Wang, Cheng; Zhao, Ran; Du, Wei-Li; Ning, Fang-Gang; Zhang, Guo-An

2014-03-01

In China, fireworks are an integral part of the celebration of the annual Spring Festival, but the number of injuries associated with their private use seen in emergency rooms increases dramatically. To raise awareness and help guide future prevention practices in this city, we investigated the epidemiology of firework-related injuries presented at our trauma and burn center in Beijing during the Spring Festivals of 2007-2011. Patients were interviewed using a pre-coded questionnaire to elicit information regarding age, gender, causes, injured body part, type of injury, diagnosis, and disposition. From 2007 to 2011, during the Spring Festivals 734 patients with fire-work related injuries were seen at our trauma and burn center in Beijing, the median patients of the five year were 140(136-150). The mean age of the patients was 26±15.3 years (range, 1-95 years). Of the 734 patients, the highest proportion of injuries were the 5-14 year-old age group The majority of the patients were male (87.9%), the overall male:female ratio was 7.41:1, and males were predominant in all age groups. For all 5 years, the incidence of firework-related injuries during the Spring Festival Holidays peaked specifically on the first, fifth, and last days, respectively. Injuries were mainly due to improper handling (415/610, 68.0%) or setting off illegal fireworks (195/610, 32.0%). The most frequently injured body parts were the hands and fingers (32.0%), head or face except eyes (28.3%), and trunk (22.4%). Burns were the most common type of injury (65.7%), most of the burned patients (437/453) were between 1% and 10%, and the most common region burned were hands and fingers (218/754). Contusions or lacerations were the second common type of injury (34.3%). Most of the patients (642, 87.5%) were treated and released, while 37 (5%) were treated and transferred, and 55 (7.5%) were admitted for advanced treatment. The private use of fireworks during the Spring Festival Holidays is associated with a considerable number of injuries to various parts of the body. We can minimize the number and severity of accidents by raising awareness of safety practices, encouraging professional displays only and motivating manufacturers to adhere to strict quality control. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Seasonal pattern of Echinococcus re-infection in owned dogs in Tibetan communities of Sichuan, China and its implications for control.

PubMed

Wang, Qian; Yu, Wen-Jie; Zhong, Bo; Shang, Jing-Ye; Huang, Liang; Mastin, Alexander; Renqingpengcuo; Huang, Yan; Zhang, Guang-Jia; He, Wei; Giraudoux, Patrick; Wu, Wei-Ping; Craig, Philip S

2016-07-05

Human cystic echinococcosis (CE) and alveolar echinococcosis (AE) are highly endemic in Tibetan communities of Sichuan Province. Previous research in the region indicated that domestic dog was the major source of human infection, and observations indicated that domestic dog could have more access to intermediate hosts of Echinococcus spp.: both domestic livestock (CE) viscera and small mammals (AE), in early winter and again in spring. We hypothesized that there would therefore be a significant increase in the risk of canine infection with Echinococcus spp. in these two seasons and conducted a reinfection study to investigate this further. Faecal samples were collected from owned dogs in seven townships in Ganze Tibetan Autonomous Prefecture (Sichuan Province, China), and Echinococcus spp. infection status was determined using copro-antigen ELISA. Dogs were sampled in April (spring), July (early summer), September/October (autumn/early winter) and December (winter) in 2009; and in April (spring) 2010. Dogs were treated with praziquantel following each of the five sample collections to eliminate any tapeworms. Information on dog sex, age and body weight was also collected. The t-test, Fisher's exact test, Poisson regression and logistic regression were used to compare means and prevalences, and to identify factors associated with infection status. The proportion of female dogs was significantly lower than that of male dogs; female dogs had significantly higher (22.78 %) baseline copro-ELISA prevalence than males (11.88 %). Dog body weight, sex, age, county and previous infection status at any sampling point had no influence on the re-infection prevalence in general. Poisson regression did not found a significant influence on the re-infection prevalence due to different deworming/sampling time spans. Dogs exhibited significantly higher re-infection prevalences in spring and early summer of 2009 and in early winter between September/October and December of 2009, suggesting a higher infection pressure in these seasons comparing with other seasons. Following praziquantel treatment, dog body weight, sex, age, county, deworming time span and previous infection status at any sampling point had no influence on the re-infection prevalence in the region in general. The differences between re-infection prevalences were probably due to the seasonality in Echinoccocus spp. infection pressure in the region. Early winter, spring and early summer should be important seasons for optimal dog deworming intervention in these Tibetan communities.

Flows in forward deformable roll coating gaps: Comparison between spring and plane-strain models of roll cover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvalho, M.S.; Scriven, L.E.

1997-12-01

In this report the flow between rigid and a deformable rotating rolls fully submerged in a liquid pool is studied. The deformation of compliant roll cover is described by two different models (1) independent, radially oriented springs that deform in response to the traction force applied at the extremity of each or one-dimensional model, and (2) a plane-strain deformation of an incompressible Mooney-Rivlin material or non-linear elastic model. Based on the flow rate predictions of both models, an empirical relation between the spring constant of the one dimensional model and the roll cover thickness and elastic modulus is proposed.

Refined Three-Dimensional Modelling of Thermally-Driven Flow in the Bormio System (Central Italian Alps)

NASA Astrophysics Data System (ADS)

Volpi, Giorgio; Riva, Federico; Frattini, Paolo; Battista Crosta, Giovanni; Magri, Fabien

2016-04-01

Thermal springs are widespread in the European Alps, where more than 80 geothermal sites are known and exploited. The quantitative assessment of those thermal flow systems is a challenging issue and requires accurate conceptual model and a thorough understanding of thermo-hydraulic properties of the aquifers. Accordingly in the last years, several qualitative studies were carried out to understand the heat and fluid transport processes driving deep fluids from the reservoir to the springs. Our work focused on thermal circulation and fluid outflows of the area around Bormio (Central Italian Alps), where nine geothermal springs discharge from dolomite bodies located close to a regional alpine thrust, called the Zebrù Line. At this site, water is heated in deep circulation systems and vigorously upwells at temperature of about 40°C. The aim of this paper is to explore the mechanisms of heat and fluid transport in the Bormio area by carrying out refined steady and transient three-dimensional finite element simulations of thermally-driven flow and to quantitatively assess the source area of the thermal waters. The full regional model (ca. 700 km2) is discretized with a highly refined triangular finite element planar grid obtained with Midas GTS NX software. The structural 3D features of the regional Zebrù thrust are built by interpolating series of geological cross sections using Fracman. A script was developed to convert and implement the thrust grid into FEFLOW mesh that comprises ca. 4 million elements. The numerical results support the observed discharge rates and temperature field within the simulated domain. Flow and temperature patterns suggest that thermal groundwater flows through a deep system crossing both sedimentary and metamorphic lithotypes, and a fracture network associated to the thrust system. Besides providing a numerical framework to simulate complex fractured systems, this example gives insights into the influence of deep alpine structures on groundwater circulation that underlies the development of many hydrothermal systems.

Attenuation of empennage buffet response through active control of damping using piezoelectric material

NASA Technical Reports Server (NTRS)

Heeg, Jennifer; Miller, Jonathan M.; Doggett, Robert V., Jr.

1993-01-01

Dynamic response and damping data obtained from buffet studies conducted in a low-speed wind tunnel by using a simple, rigid model attached to spring supports are presented. The two parallel leaf spring supports provided a means for the model to respond in a vertical translation mode, thus simulating response in an elastic first bending mode. Wake-induced buffeting flow was created by placing an airfoil upstream of the model of that the wake of the airfoil impinged on the model. Model response was sensed by a strain gage mounted on one of the springs. The output signal from the strain gage was fed back through a control law implemented on a desktop computer. The processed signals were used to 'actuate' a piezoelectric bending actuator bonded to the other spring in such a way as to add damping as the model responded. The results of this 'proof-of-concept' study show that the piezoelectric actuator was effective in attenuating the wake-induced buffet response over the range of parameters investigated.

Computer program for the load and trajectory analysis of two DOF bodies connected by an elastic tether: Users manual

NASA Technical Reports Server (NTRS)

Doyle, G. R., Jr.; Burbick, J. W.

1973-01-01

The derivation of the differential equations of motion of a 3 Degrees of Freedom body joined to a 3 Degrees of Freedom body by an elastic tether. The tether is represented by a spring and dashpot in parallel. A computer program which integrates the equations of motion is also described. Although the derivation of the equations of motions are for a general system, the computer program is written for defining loads in large boosters recovered by parachutes.

Fabrication and modeling of shape memory alloy springs

NASA Astrophysics Data System (ADS)

Heidari, B.; Kadkhodaei, M.; Barati, M.; Karimzadeh, F.

2016-12-01

In this paper, shape memory alloy (SMA) helical springs are produced by shape setting two sets of NiTi (Ti-55.87 at% Ni) wires, one of which showing shape memory effect and another one showing pseudoelasticity at the ambient temperature. Different pitches as well as annealing temperatures are tried to investigate the effect of such parameters on the thermomechanical characteristics of the fabricated springs. Phase transformation temperatures of the products are measured by differential scanning calorimetry and are compared with those of the original wires. Compression tests are also carried out, and stiffness of each spring is determined. The desired pitches are so that a group of springs experiences phase transition during loading while the other does not. The former shows a varying stiffness upon the application of compression, but the latter acts as passive springs with a predetermined stiffness. Based on the von-Mises effective stress and strain, an enhanced one-dimensional constitutive model is further proposed to describe the shear stress-strain response within the coils of an SMA spring. The theoretically predicted force-displacement responses of the produced springs are shown to be in a reasonable agreement with the experimental results. Finally, effects of variations in geometric parameters on the axial force-displacement response of an SMA spring are investigated.

Seasonal shifts in the thermal biology of the lizard Liolaemus tandiliensis (Squamata, Liolaemidae).

PubMed

Stellatelli, Oscar Aníbal; Villalba, Agustina; Block, Carolina; Vega, Laura Estela; Dajil, Juan Esteban; Cruz, Félix Benjamín

2018-04-01

Small lizards can accommodate to constraints imposed by temporal changes in ambient temperature through a combination of adaptive evolution and behavioral and physiological plasticity. Thermal physiology plasticity may compensate for climate variation and favor performance while minimizing behavioral costs in sub-optimal conditions. The Tandilia's lizard, Liolaemus tandiliensis, occurs in an isolated mountain range of the Argentinean temperate Pampas. In this study, we compared the thermal biology of L. tandiliensis between late spring (December) and mid-summer (February). The habitats' thermal quality was lower in late spring than in mid-summer. The lizard's field-body temperature (Tb) was 2-3 °C higher than the operative temperature (Te). Overall, the mean preferred temperature (Tsel) was 37.4 °C [preferred range (Tset): 36.2-38.7 °C], and was similar to other Liolaemus species. The Tset and Tsel of females in late spring were 1.8 °C lower than in mid-summer. In the case of males, the Tsel did not vary among seasons, while the Tset had a difference of 2.5 °C between seasons. Adults were moderate thermoregulators, but females were more efficient only in late spring (E males = 0.69; E females = 0.58), compared to mid-summer (E males = 0.68; E females = 0.50). Juveniles did not show temporal differences in temperature preferences and had a relatively higher efficiency in late spring (E = 0.38) compared to mid-summer (E = 0.28). An increased proportion of juveniles and adults shifted their Tb near to the Tset in late spring respect to mid-summer. The adults also matched their preferred temperatures to their current body temperature. These results suggest that seasonal shifts in the thermoregulatory parameters of L. tandiliensis may improve their thermoregulatory efficiency. Although temporal variation in ambient temperatures might influence the thermal biology of the studied lizards, other factors such as changes in the reproductive status may have also interfered. Copyright © 2018 Elsevier Ltd. All rights reserved.

Attitude stability of spinning flexible spacecraft

NASA Technical Reports Server (NTRS)

Likins, P. W.; Barbera, F. J.

1971-01-01

The stability of spinning flexible satellites in a force-free environment was analyzed. The satellite was modeled as a rigid core having attached to it a flexible appendage idealized as a collection of particles (point masses) interconnected by springs. Both Liapunov and Routh-Hurwitz stability procedures are used. In the former, the Hamiltonian of the system, constrained through the angular momentum integral so as to admit complete damping, is used as a testing function. Equations of motion are written using the hybrid coordinate formulation, which readily accepts a modal coordinate transformation ultimately allowing truncation to a level amenable to literal stability analysis. Closed form stability criteria are generated for the first mode of a restricted appendage model lying in a plane containing the system center of mass and orthogonal to the spin axis. The effects of spin on flexible bodies are discussed by considering a very elementary particle model. Control of passively unstable spacecraft is briefly considered.

Long distance migratory songbirds respond to extremes in arctic seasonality

NASA Astrophysics Data System (ADS)

Boelman, N.; Asmus, A.; Chmura, H.; Krause, J.; Perez, J. H.; Sweet, S. K.; Gough, L.; Wingfield, J.

2017-12-01

Arctic regions are warming rapidly, with extreme weather events increasing in frequency, duration and intensity, as in other regions. Many studies have focused on how shifting seasonality in environmental conditions affect the phenology and productivity of vegetation, while far fewer have examined how arctic fauna responds. We studied two species of long-distance migratory songbirds, Lapland longspurs, Calcarius lapponicus, and White-crowned sparrows, Zonotrichia leucophrys gambelii, across seven consecutive breeding seasons in northern Alaskan tundra. We aimed to understand how spring environmental conditions affected breeding cycle phenology, food availability, body condition, stress physiology, and ultimately, reproductive success. Spring temperatures, precipitation, storm frequency, and snow-free dates differed significantly among years, with 2013 characterized by unusually late snow cover, and 2015 and 2016 characterized by unusually early snow-free dates and several late spring snowstorms. In response, we found that relative to other study years, there was a significant delay in breeding cycle phenology for both study species in 2013, while breeding cycle phenology was significantly earlier in 2015 only. For both species, we also found significant variation among years in: the seasonal patterns of arthropod availability during the nesting stage; body condition, and; stress physiology. Finally, we found significant variation in reproductive success of both species across years, and that daily survival rates were decreased by snow storm events. Our findings suggest that arctic-breeding passerine communities may be able to adjust phenology to unpredictable shifts in the timing of spring, but extreme conditions during the incubation and nestling stages are detrimental to reproductive success.

Apparent CFC and 3H/ 3He age differences in water from Floridan Aquifer springs

NASA Astrophysics Data System (ADS)

Happell, James D.; Opsahl, Stephen; Top, Zafer; Chanton, Jeffrey P.

2006-03-01

The apparent CFC-11, -12 and -113 ages of Upper Floridan Aquifer water discharged from 31 springs located in Florida and Georgia ranged from 11 to 44 years when samples were collected in 2002 and 2003. Apparent 3H/ 3He ages in these springs ranged from 12 to 66 years. Some of the springs sampled did not yield valid CFC ages because one or more of the CFCs were contaminated by non-atmospheric sources. Of the 31 springs sampled, six were contaminated with all three CFCs and nine were contaminated with one or two CFCs. Of the remaining 16 springs, the CFC distributions of four could be modeled assuming a single source of water, and 11 were best modeled by assuming two sources of water, with one of the water sources >60 years old. The CFC and 3H/ 3He apparent ages and the simple mixing models applied to these ages suggest that past impacts to the water quality of water recharging the sampled springs may take anywhere from 0 to ˜60 years or more to appear in the discharging spring water. In 27 springs where both 3H/ 3He ages and CFC ages were available, five springs gave similar results between the two techniques, while in the other 22 cases the 3H/ 3He apparent ages were 8-40 years greater than the CFC ages. Large excesses of 4He were observed in many of the springs, consistent with a source of older water. This older water may also carry an additional and unaccounted for source of 3He, which may be responsible for the greater 3H/ 3He ages relative to the CFC ages. We believe that the large excess 3He and 4He values and apparent age differences are related to regional climate variations because our samples were obtained at the end of a 4-year drought.

An integrative model of risk for high school disordered eating.

PubMed

Davis, Heather A; Smith, Gregory T

2018-06-21

Binge eating and purging behaviors are associated with significant harm and distress among adolescents. The process by which these behaviors develop (often in the high school years) is not fully understood. We tested the Acquired Preparedness (AP) model of risk involving transactions among biological, personality, and psychosocial factors to predict binge eating and purging behavior in a sample of 1,906 children assessed in the spring of 5th grade (the last year of elementary school), the fall of 6th grade (the first year of middle school), spring of 6th grade, and spring of 10th grade (second year of high school). Pubertal onset in spring of 5th grade predicted increases in negative urgency, but not negative affect, in the fall of 6th grade. Negative urgency in the fall of 6th grade predicted increases in expectancies for reinforcement from eating in the spring of 6th grade, which in turn predicted increases in binge eating behavior in the spring of 10th grade. Negative affect in the fall of 6th grade predicted increases in thinness expectancies in the spring of 6th grade, which in turn predicted increases in purging in the spring of 10th grade. Results demonstrate similarities and differences in the development of these two different bulimic behaviors. Intervention efforts targeting the risk factors evident in this model may prove fruitful in the treatment of eating disorders characterized by binge eating and purging. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Thermal quality influences effectiveness of thermoregulation, habitat use, and behaviour in milk snakes.

PubMed

Row, Jeffrey R; Blouin-Demers, Gabriel

2006-05-01

We investigated the link between thermal quality and the effectiveness of thermoregulation in milk snakes in a thermally challenging environment. We defined thermoregulatory effectiveness as the extent to which an individual maintains its body temperature (Tb) closer to the preferred range (Tset) than allowed by the thermal quality of its environment. We defined thermal quality as the magnitude of the difference between operative environmental temperatures (Te) and Tset. Because ectotherms regulate body temperatures through choice of habitat and behavioural adjustments, we also examined the link between thermoregulation, habitat use and behaviour. During 2003-2004, we located 25 individuals 890 times, and recorded their Tb. Thermal quality was lower in the spring and fall than in the summer, and was lower in forests than in open habitats. Milk snakes thermoregulated more effectively in the spring than in the summer and fall, and more effectively in the forest than in open habitats. Milk snakes had a strong preference for open habitats in all seasons, which was likely to facilitate behavioural thermoregulation. The preference for open habitats was equally strong in all seasons and, therefore, the higher effectiveness of thermoregulation was not a result of altered habitat use. Instead, milk snakes modified their behaviour and were seen basking more and moved less in the spring than in the summer.

Analytical model for viscous damping and the spring force for perforated planar microstructures acting at both audible and ultrasonic frequencies

PubMed Central

Homentcovschi, Dorel; Miles, Ronald N.

2008-01-01

The paper presents a model for the squeezed film damping, the resistance of the holes, and the corresponding spring forces for a periodic perforated microstructure including the effects of compressibility, inertia, and rarefied gas. The viscous damping and spring forces are obtained by using the continuity equation. The analytical formula for the squeezed film damping is applied to analyze the response of an ultrasonic transducer. The inclusion of these effects in a model significantly improves the agreement with measured results. Finally, it is shown that the frequency dependence of the total damping and total spring force for a cell are very similar to those corresponding to a rectangular open microstructure without holes. A separate analysis reveals the importance of each particular correction. The most important is the compressibility correction; the inertia has to be considered only for determining the spring force and the damping force for sufficiently high frequencies. PMID:18646964

Technical Note: Initial assessment of a multi-method approach to spring-flood forecasting in Sweden

NASA Astrophysics Data System (ADS)

Olsson, J.; Uvo, C. B.; Foster, K.; Yang, W.

2016-02-01

Hydropower is a major energy source in Sweden, and proper reservoir management prior to the spring-flood onset is crucial for optimal production. This requires accurate forecasts of the accumulated discharge in the spring-flood period (i.e. the spring-flood volume, SFV). Today's SFV forecasts are generated using a model-based climatological ensemble approach, where time series of precipitation and temperature from historical years are used to force a calibrated and initialized set-up of the HBV model. In this study, a number of new approaches to spring-flood forecasting that reflect the latest developments with respect to analysis and modelling on seasonal timescales are presented and evaluated. Three main approaches, represented by specific methods, are evaluated in SFV hindcasts for the Swedish river Vindelälven over a 10-year period with lead times between 0 and 4 months. In the first approach, historically analogue years with respect to the climate in the period preceding the spring flood are identified and used to compose a reduced ensemble. In the second, seasonal meteorological ensemble forecasts are used to drive the HBV model over the spring-flood period. In the third approach, statistical relationships between SFV and the large-sale atmospheric circulation are used to build forecast models. None of the new approaches consistently outperform the climatological ensemble approach, but for early forecasts improvements of up to 25 % are found. This potential is reasonably well realized in a multi-method system, which over all forecast dates reduced the error in SFV by ˜ 4 %. This improvement is limited but potentially significant for e.g. energy trading.

Finite Element Analysis Of Structural And Magmatic Interactions At Mono Basin (California)

NASA Astrophysics Data System (ADS)

La Marra, D.; Manconi, A.; Battaglia, M.

2010-12-01

Mono Basin is a northward trending graben situated east of the Sierra Nevada and west of Cowtrack Mountains, extending from the northern edge of Long Valley Caldera towards the Bodie Hills. From a hydrographic perspective, the Mono Basin is defined by all streams that drain into Mono Lake. The Mono-Inyo Craters forms a prominent 25-km-long volcanic complex from the NW corner of Long Valley caldera to the southern edge of Mono Lake. The late Quaternary Hartley Springs fault occurs along the Sierran range front between June Lake and the northern border of Long Valley Caldera. Recently it has been proposed that the manifestation of the volcanic and of the tectonic activity in this area is likely interrelated. According to Bursik et al (2003), stratigraphic data suggest that during the North Mono-Inyo eruption sequence of ~1350 A.D., a series of strong earthquakes occurred across the end of the North Mono explosive phase and the beginning of the Inyo explosive phase. Moreover, geological and geomorphic features of the Hartley Springs fault are consistent with rupture of the fault during the eruption sequence. We use the Finite Element Method (FEM) to simulate a three-dimensional model and investigate the feedback mechanism between dike intrusion and slip along the Hartley Springs fault. We first validate our numerical model against the Okada (1985) analytical solution for a homogeneous and elastic flat half-space. Subsequently, we evaluate the distribution of local stress changes to study the influence of the Inyo Dike intrusion in ~1350 A.D. on Hartley Springs fault, and how the fault slip may encourage the propagation of dikes towards the surface. To this end, we considered the standard Coulomb stress change as failure criterion. Finally, we analyze the effects of the topography and of vertical and lateral heterogeneities of the crust on the distribution of local and regional stress changes. In this presentation, we highlight the preliminary results of our analysis and discuss the possible future developments of this study.

Informing geobiology through GIS site suitability analysis: locating springs in mantle units of ophiolites

NASA Astrophysics Data System (ADS)

Bowman, A.; Cardace, D.; August, P.

2012-12-01

Springs sourced in the mantle units of ophiolites serve as windows to the deep biosphere, and thus hold promise in elucidating survival strategies of extremophiles, and may also inform discourse on the origin of life on Earth. Understanding how organisms can survive in extreme environments provides clues to how microbial life responds to gradients in pH, temperature, and oxidation-reduction potential. Spring locations associated with serpentinites have traditionally been located using a variety of field techniques. The aqueous alteration of ultramafic rocks to serpentinites is accompanied by the production of very unusual formation fluids, accessed by drilling into subsurface flow regimes or by sampling at related surface springs. The chemical properties of these springs are unique to water associated with actively serpentinizing rocks; they reflect a reducing subsurface environment reacting at low temperatures producing high pH, Ca-rich formation fluids with high dissolved hydrogen and methane. This study applies GIS site suitability analysis to locate high pH springs upwelling from Coast Range Ophiolite serpentinites in Northern California. We used available geospatial data (e.g., geologic maps, topography, fault locations, known spring locations, etc.) and ArcGIS software to predict new spring localities. Important variables in the suitability model were: (a) bedrock geology (i.e., unit boundaries and contacts for peridotite, serpentinite, possibly pyroxenite, or chromite), (b) fault locations, (c) regional data for groundwater characteristics such as pH, Ca2+, and Mg2+, and (d) slope-aspect ratio. The GIS model derived from these geological and environmental data sets predicts the latitude/longitude points for novel and known high pH springs sourced in serpentinite outcrops in California. Field work confirms the success of the model, and map output can be merged with published environmental microbiology data (e.g., occurrence of hydrogen-oxidizers) to showcase patterns in microbial community structure. Discrepancies between predicted and actual spring locations are then used to tune GIS suitability analysis, re-running the model with corrected geo-referenced data. This presentation highlights a powerful GIS-based technique for accelerating field exploration in this area of ongoing research.

Numerical Study of Groundwater Flow and Salinity Distribution Cycling Controlled by Seawater/Freshwater Interaction in Karst Aquifer Using SEAWAT

NASA Astrophysics Data System (ADS)

Xu, Z.; Hu, B.

2017-12-01

The interest to predict seawater intrusion and salinity distribution in Woodville Karst Plain (WKP) has increased due to the huge challenge on quality of drinkable water and serious environmental problems. Seawater intrudes into the conduit system from submarine karst caves at Spring Creek Spring due to density difference and sea level rising, nowadays the low salinity has been detected at Wakulla Spring which is 18 km from coastal line. The groundwater discharge at two major springs and salinity distribution in this area is controlled by the seawater/freshwater interaction under different rainfall conditions: during low rainfall periods, seawater flow into the submarine spring through karst windows, then the salinity rising at the submarine spring leads to seawater further intrudes into conduit system; during high rainfall periods, seawater is pushed out by fresh water discharge at submarine spring. The previous numerical studies of WKP mainly focused on the density independent transport modeling and seawater/freshwater discharge at major karst springs, in this study, a SEAWAT model has been developed to fully investigate the salinity distribution in the WKP under repeating phases of low rainfall and high rainfall periods, the conduit system was simulated as porous media with high conductivity and porosity. The precipitation, salinity and discharge at springs were used to calibrate the model. The results showed that the salinity distribution in porous media and conduit system is controlled by the rainfall change, in general, the salinity distribution inland under low rainfall conditions is much higher and wider than the high rainfall conditions. The results propose a prediction on the environmental problem caused by seawater intrusion in karst coastal aquifer, in addition, provide a visual and scientific basis for future groundwater remediation.

Influence of biotic variables on invertebrate size structure and diversity in coastal wetlands of Southeastern Spain

NASA Astrophysics Data System (ADS)

Antón-Pardo, María; Armengol, Xavier

2016-10-01

Biomass and size-based estimations provide relevant information regarding ecosystem functioning and biotic interactions. Our aims were to study the effect of fish and macrophytes on the size structure of invertebrate assemblages (from rotifers to insects) in a set of coastal water bodies, estimating the biomass (total and main invertebrate groups), the biomass-size spectra (model of Pareto) and size diversity. In fishless ponds, cladoceran and ostracod biomass were higher, and they presented greater size diversity. In fish ponds, rotifer biomass presented greater proportion; while in fishless ponds, cladocerans were usually the most abundant taxa and the largest organisms. The biomass size spectra showed more irregularities in fishless ponds, due to the low densities of small taxa (rotifers and copepod juveniles) and big taxa (malacostraceans or insects). Differences is size structure and diversity were also observed between spring and summer, suggesting a higher recruitment of juveniles in spring, and thus, a higher predation pressure upon zooplankton at that moment. Macrophyte cover did not apparently influence those parameters, except for the biomass of ostracods, copepods, and insects. Therefore, predation by fish strongly affected invertebrate biomass, reflecting their selective feeding, and allowing high densities of small taxa. Predation pressure decreased size diversity, by limiting the abundance of vulnerable taxa of specific size. Seasonal changes were likely related to the spring recruitment of fish juveniles. The presence of small fish and invertebrate predator taxa among the macrophytes, restrict their role as refuges for prey invertebrates.

The use of subsurface thermal data, isotopic tracers and earthquake hypocenter locations to unravel deep regional flow systems within the crystalline basement beneath the Rio Grande rift, New Mexico. (Invited)

NASA Astrophysics Data System (ADS)

Person, M. A.; Woolsey, E.; Pepin, J.; Crossey, L. J.; Karlstrom, K. E.; Phillips, F. M.; Kelley, S.; Timmons, S.

2013-12-01

The Rio Grande rift in New Mexico hosts a number of low-temperature geothermal systems as well as the 19 km deep Socorro Magma Body. The presence of a mantle helium anomaly measured at San Acacia spring (3He/4He = 0.295 RA) and in an adjacent shallow well (50m < ; 0.8 RA) overlying the Socorro Magma Body at the southern terminus of the Albuquerque Basin suggests that deeply sourced fluids mix with the sedimentary basin groundwater flow system. Temperatures recorded at the base of the San Acacia well is elevated (29 oC). Published estimates of uplift rates and heat flow suggest that the magma body was emplaced about 1-3 ka and reflects a long-lived (several Ma) magmatic system. Further south near the southern terminus of the Engle Basin, much warmer temperatures (42 oC) occur at shallow depths within the spa district in the town of Truth or Consequences at shallow depths also suggesting deep-fluid circulation. 14C constrained apparent groundwater residence times in the spa district range between 6-10 ka. We have developed two 6-19 km deep crustal-scale, cross-sectional models that simulate subsurface fluid flow, heat and isotope (3He/4He) transport as well as groundwater residence times along the Rio Grande rift. The North-South oriented model of the Albuquerque Basin incorporates a high-permeability conduit 100 m wide having hydrologic properties differing from surrounding crystalline basement units. We use these models to constrain the crustal permeability structure and fluid circulation patterns beneath the Albuquerque and Engle Basins. Model results are compared to measurements of groundwater temperatures, residence times (14C), and 3He/4He data. We also use the distribution of earthquake hypocenters to constrain likely fault-crystalline basement hydraulic interactions in the seismogenic crust above the Socorro Magma Body. For the case of the southern Albuquerque Basin, conduit permeability associated with the Indian Hill conduit/fault zone must range between about 1.0E-13 to 1.0E-15 m2 in order for simulated 3He/4He, solute concentrations, and temperatures to match observed conditions. Basement permeability outside of the fault damage zone must range between 1.0E-17 to 1.0E-18 m2. However, a much longer transport time is required (between about 20-30 ka) in order to match observed conditions suggesting multiple magmatic intrusion events. For the case of the Engle Basin near Truth or Consequences, bulk crustal permeability between a depth of 2-6 km below the sedimentary succession must approach 1.0E-12 m2 in order to reproduce hot spring temperatures and groundwater residence times. We compare these model derived permeability estimates to published permeability-depth relationships for crustal rocks (Manning and Ingebritsen, 1999; Ingebritsen and Manning, 2010).

Crop status evaluations and yield predictions

NASA Technical Reports Server (NTRS)

Haun, J. R.

1975-01-01

The growth-environment relationships for greenhouse and field conditions are compared, and the development of growth-prediction models for spring wheat is discussed along with the development of models for predicting the date for spring wheat emergence in North Dakota.

Quiz: What's the buzz about salt? | NIH MedlinePlus the Magazine

MedlinePlus

... page please turn Javascript on. Feature: Too Much Salt Quiz: What's the buzz about salt? Past Issues / Spring - Summer 2010 Table of Contents The body needs how much salt per day: ¼ teaspoon ½ teaspoon 1 teaspoon ...

Wing-pitch modulation in maneuvering fruit flies is explained by an interplay between aerodynamics and a torsional spring.

PubMed

Beatus, Tsevi; Cohen, Itai

2015-08-01

While the wing kinematics of many flapping insects have been well characterized, understanding the underlying sensory, neural, and physiological mechanisms that determine these kinematics is still a challenge. Two main difficulties in understanding the physiological mechanisms arise from the complexity of the interaction between a flapping wing and its own unsteady flow, as well as the intricate mechanics of the insect wing hinge, which is among the most complicated joints in the animal kingdom. These difficulties call for the application of reduced-order approaches. Here this strategy is used to model the torques exerted by the wing hinge along the wing-pitch axis of maneuvering fruit flies as a damped torsional spring with elastic and damping coefficients as well as a rest angle. Furthermore, we model the air flows using simplified quasistatic aerodynamics. Our findings suggest that flies take advantage of the passive coupling between aerodynamics and the damped torsional spring to indirectly control their wing-pitch kinematics by modulating the spring parameters. The damped torsional-spring model explains the changes measured in wing-pitch kinematics during roll correction maneuvers through modulation of the spring damping and elastic coefficients. These results, in conjunction with the previous literature, indicate that flies can accurately control their wing-pitch kinematics on a sub-wing-beat time scale by modulating all three effective spring parameters on longer time scales.

Wing-pitch modulation in maneuvering fruit flies is explained by an interplay between aerodynamics and a torsional spring

NASA Astrophysics Data System (ADS)

Beatus, Tsevi; Cohen, Itai

2015-08-01

While the wing kinematics of many flapping insects have been well characterized, understanding the underlying sensory, neural, and physiological mechanisms that determine these kinematics is still a challenge. Two main difficulties in understanding the physiological mechanisms arise from the complexity of the interaction between a flapping wing and its own unsteady flow, as well as the intricate mechanics of the insect wing hinge, which is among the most complicated joints in the animal kingdom. These difficulties call for the application of reduced-order approaches. Here this strategy is used to model the torques exerted by the wing hinge along the wing-pitch axis of maneuvering fruit flies as a damped torsional spring with elastic and damping coefficients as well as a rest angle. Furthermore, we model the air flows using simplified quasistatic aerodynamics. Our findings suggest that flies take advantage of the passive coupling between aerodynamics and the damped torsional spring to indirectly control their wing-pitch kinematics by modulating the spring parameters. The damped torsional-spring model explains the changes measured in wing-pitch kinematics during roll correction maneuvers through modulation of the spring damping and elastic coefficients. These results, in conjunction with the previous literature, indicate that flies can accurately control their wing-pitch kinematics on a sub-wing-beat time scale by modulating all three effective spring parameters on longer time scales.

An evaluation and geochemical survey of the Farah Garan East Prospect, Southeast Asir, Kingdom of Saudi Arabia

USGS Publications Warehouse

Bookstrom, Arthur A.; El Komi, Mohamed; Christian, Ralph P.; Bazzari, Maher A.

1990-01-01

Ore minerals in outcrops, and geochemically anomalous concentrations of gold, silver, copper, lead, zinc, arsenic, antimony, and tellurium are present in carbonate-rich rocks of the hot-spring assemblage. This indicates that the ore minerals and elements were deposited originally as constituents of the hot-spring assemblage. However, exposed ore-mineral occurrences are small and sparse, and geochemical anomalies are small, irregularly distributed, and of subeconomic grade. Furthermore, weak electromagnetic anomalies do not indicate the presence of subsurface bodies of concentrated, conductive ore minerals. Therefore, no drilling is recommended.

Predictors of fielding performance in professional baseball players.

PubMed

Mangine, Gerald T; Hoffman, Jay R; Vazquez, Jose; Pichardo, Napoleon; Fragala, Maren S; Stout, Jeffrey R

2013-09-01

The ultimate zone-rating extrapolation (UZR/150) rates fielding performance by runs saved or cost within a zone of responsibility in comparison with the league average (150 games) for a position. Spring-training anthropometric and performance measures have been previously related to hitting performance; however, their relationships with fielding performance measures are unknown. To examine the relationship between anthropometric and performance measurements on fielding performance in professional baseball players. Body mass, lean body mass (LBM), grip strength, 10-yd sprint, proagility, and vertical-jump mean (VJMP) and peak power (VJPP) were collected during spring training over the course of 5 seasons (2007-2011) for professional corner infielders (CI; n = 17, fielding opportunities = 420.7 ± 307.1), middle infielders (MI; n = 14, fielding opportunities = 497.3 ± 259.1), and outfielders (OF; n = 16, fielding opportunities = 227.9 ± 70.9). The relationships between these data and regular-season (100-opportunity minimum) fielding statistics were examined using Pearson correlation coefficients, while stepwise regression identified the single best predictor of UZR/150. Significant correlations (P < .05) were observed between UZR/150 and body mass (r = .364), LBM (r = .396), VJPP (r = .397), and VJMP (r = .405). Of these variables, stepwise regression indicated VJMP (R = .405, SEE = 14.441, P = .005) as the single best predictor for all players, although the addition of proagility performance strengthened (R = .496, SEE = 13.865, P = .002) predictive ability by 8.3%. The best predictor for UZR/150 was body mass for CI (R = .519, SEE = 15.364, P = .033) and MI (R = .672, SEE = 12.331, P = .009), while proagility time was the best predictor for OF (R = .514, SEE = 8.850, P = .042). Spring-training measurements of VJMP and proagility time may predict the defensive run value of a player over the course of a professional baseball season.

Attribution of spring snow water equivalent (SWE) changes over the northern hemisphere to anthropogenic effects

NASA Astrophysics Data System (ADS)

Jeong, Dae Il; Sushama, Laxmi; Naveed Khaliq, M.

2017-06-01

Snow is an important component of the cryosphere and it has a direct and important influence on water storage and supply in snowmelt-dominated regions. This study evaluates the temporal evolution of snow water equivalent (SWE) for the February-April spring period using the GlobSnow observation dataset for the 1980-2012 period. The analysis is performed for different regions of hemispherical to sub-continental scales for the Northern Hemisphere. The detection-attribution analysis is then performed to demonstrate anthropogenic and natural effects on spring SWE changes for different regions, by comparing observations with six CMIP5 model simulations for three different external forcings: all major anthropogenic and natural (ALL) forcings, greenhouse gas (GHG) forcing only, and natural forcing only. The observed spring SWE generally displays a decreasing trend, due to increasing spring temperatures. However, it exhibits a remarkable increasing trend for the southern parts of East Eurasia. The six CMIP5 models with ALL forcings reproduce well the observed spring SWE decreases at the hemispherical scale and continental scales, whereas important differences are noted for smaller regions such as southern and northern parts of East Eurasia and northern part of North America. The effects of ALL and GHG forcings are clearly detected for the spring SWE decline at the hemispherical scale, based on multi-model ensemble signals. The effects of ALL and GHG forcings, however, are less clear for the smaller regions or with single-model signals, indicating the large uncertainty in regional SWE changes, possibly due to stronger influence of natural climate variability.

Free vibration analysis of a cracked shear deformable beam on a two-parameter elastic foundation using a lattice spring model

NASA Astrophysics Data System (ADS)

Attar, M.; Karrech, A.; Regenauer-Lieb, K.

2014-05-01

The free vibration of a shear deformable beam with multiple open edge cracks is studied using a lattice spring model (LSM). The beam is supported by a so-called two-parameter elastic foundation, where normal and shear foundation stiffnesses are considered. Through application of Timoshenko beam theory, the effects of transverse shear deformation and rotary inertia are taken into account. In the LSM, the beam is discretised into a one-dimensional assembly of segments interacting via rotational and shear springs. These springs represent the flexural and shear stiffnesses of the beam. The supporting action of the elastic foundation is described also by means of normal and shear springs acting on the centres of the segments. The relationship between stiffnesses of the springs and the elastic properties of the one-dimensional structure are identified by comparing the homogenised equations of motion of the discrete system and Timoshenko beam theory.

Preliminary results on the dynamics of large and flexible space structures in Halo orbits

NASA Astrophysics Data System (ADS)

Colagrossi, Andrea; Lavagna, Michèle

2017-05-01

The global exploration roadmap suggests, among other ambitious future space programmes, a possible manned outpost in lunar vicinity, to support surface operations and further astronaut training for longer and deeper space missions and transfers. In particular, a Lagrangian point orbit location - in the Earth- Moon system - is suggested for a manned cis-lunar infrastructure; proposal which opens an interesting field of study from the astrodynamics perspective. Literature offers a wide set of scientific research done on orbital dynamics under the Three-Body Problem modelling approach, while less of it includes the attitude dynamics modelling as well. However, whenever a large space structure (ISS-like) is considered, not only the coupled orbit-attitude dynamics should be modelled to run more accurate analyses, but the structural flexibility should be included too. The paper, starting from the well-known Circular Restricted Three-Body Problem formulation, presents some preliminary results obtained by adding a coupled orbit-attitude dynamical model and the effects due to the large structure flexibility. In addition, the most relevant perturbing phenomena, such as the Solar Radiation Pressure (SRP) and the fourth-body (Sun) gravity, are included in the model as well. A multi-body approach has been preferred to represent possible configurations of the large cis-lunar infrastructure: interconnected simple structural elements - such as beams, rods or lumped masses linked by springs - build up the space segment. To better investigate the relevance of the flexibility effects, the lumped parameters approach is compared with a distributed parameters semi-analytical technique. A sensitivity analysis of system dynamics, with respect to different configurations and mechanical properties of the extended structure, is also presented, in order to highlight drivers for the lunar outpost design. Furthermore, a case study for a large and flexible space structure in Halo orbits around one of the Earth-Moon collinear Lagrangian points, L1 or L2, is discussed to point out some relevant outcomes for the potential implementation of such a mission.

Compliance matrices for cracked bodies

NASA Technical Reports Server (NTRS)

Ballarini, R.

1986-01-01

An algorithm is developed to construct the compliance matrix for a cracked solid in the integral-equation formulation of two-dimensional linear-elastic fracture mechanics. The integral equation is reduced to a system of algebraic equations for unknown values of the dislocation-density function at discrete points on the interval from -1 to 1, using the numerical procedure described by Gerasoulis (1982). Sample numerical results are presented, and it is suggested that the algorithm is especially useful in cases where iterative solutions are required; e.g., models of fiber-reinforced concrete, rocks, or ceramics where microcracking, fiber bridging, and other nonlinear effects are treated as nonlinear springs along the crack surfaces (Ballarini et al., 1984).

An MDA Based Ontology Platform: AIR

NASA Astrophysics Data System (ADS)

Gaševic, Dragan; Djuric, Dragan; Devedžic, Vladan

In the past few years, software engineering has witnessed two major shifts: model-driven engineering has entered the mainstream, and some leading development tools have become open and extensible.1 AI has always been a spring of new ideas that have been adopted in software engineering, but most of its gems have stayed buried in laboratories, available only to a limited number of AI practitioners. Should AI tools be integrated into mainstream tools and could it be done? We think that it is feasible, and that both communities can benefit from this integration. In fact, some efforts in this direction have already been made, both by major industrial standardization bodies such as the OMG, and by academic laboratories.

Convergent evolution of reduced energy demands in extremophile fish

PubMed Central

Arias-Rodriguez, Lenin; Tobler, Michael

2017-01-01

Convergent evolution in organismal function can arise from nonconvergent changes in traits that contribute to that function. Theory predicts that low resource availability and high maintenance costs in extreme environments select for reductions in organismal energy demands, which could be attained through modifications of body size or metabolic rate. We tested for convergence in energy demands and underlying traits by investigating livebearing fish (genus Poecilia) that have repeatedly colonized toxic, hydrogen sulphide-rich springs. We quantified variation in body size and routine metabolism across replicated sulphidic and non-sulphidic populations in nature, modelled total organismal energy demands, and conducted a common-garden experiment to test whether population differences had a genetic basis. Sulphidic populations generally exhibited smaller body sizes and lower routine metabolic rates compared to non-sulphidic populations, which together caused significant reductions in total organismal energy demands in extremophile populations. Although both mechanisms contributed to variation in organismal energy demands, variance partitioning indicated reductions of body size overall had a greater effect than reductions of routine metabolism. Finally, population differences in routine metabolism documented in natural populations were maintained in common-garden reared individuals, indicating evolved differences. In combination with other studies, these results suggest that reductions in energy demands may represent a common theme in adaptation to physiochemical stressors. Selection for reduced energy demand may particularly affect body size, which has implications for life history evolution in extreme environments. PMID:29077740

Nonlinear Friction Compensation of Ball Screw Driven Stage Based on Variable Natural Length Spring Model and Disturbance Observer

NASA Astrophysics Data System (ADS)

Asaumi, Hiroyoshi; Fujimoto, Hiroshi

Ball screw driven stages are used for industrial equipments such as machine tools and semiconductor equipments. Fast and precise positioning is necessary to enhance productivity and microfabrication technology of the system. The rolling friction of the ball screw driven stage deteriorate the positioning performance. Therefore, the control system based on the friction model is necessary. In this paper, we propose variable natural length spring model (VNLS model) as the friction model. VNLS model is simple and easy to implement as friction controller. Next, we propose multi variable natural length spring model (MVNLS model) as the friction model. MVNLS model can represent friction characteristic of the stage precisely. Moreover, the control system based on MVNLS model and disturbance observer is proposed. Finally, the simulation results and experimental results show the advantages of the proposed method.

TOUGH-RBSN simulator for hydraulic fracture propagation within fractured media: Model validations against laboratory experiments

NASA Astrophysics Data System (ADS)

Kim, Kunhwi; Rutqvist, Jonny; Nakagawa, Seiji; Birkholzer, Jens

2017-11-01

This paper presents coupled hydro-mechanical modeling of hydraulic fracturing processes in complex fractured media using a discrete fracture network (DFN) approach. The individual physical processes in the fracture propagation are represented by separate program modules: the TOUGH2 code for multiphase flow and mass transport based on the finite volume approach; and the rigid-body-spring network (RBSN) model for mechanical and fracture-damage behavior, which are coupled with each other. Fractures are modeled as discrete features, of which the hydrological properties are evaluated from the fracture deformation and aperture change. The verification of the TOUGH-RBSN code is performed against a 2D analytical model for single hydraulic fracture propagation. Subsequently, modeling capabilities for hydraulic fracturing are demonstrated through simulations of laboratory experiments conducted on rock-analogue (soda-lime glass) samples containing a designed network of pre-existing fractures. Sensitivity analyses are also conducted by changing the modeling parameters, such as viscosity of injected fluid, strength of pre-existing fractures, and confining stress conditions. The hydraulic fracturing characteristics attributed to the modeling parameters are investigated through comparisons of the simulation results.

A natural tracer investigation of the hydrological regime of Spring Creek Springs, the largest submarine spring system in Florida

NASA Astrophysics Data System (ADS)

Dimova, Natasha T.; Burnett, William C.; Speer, Kevin

2011-04-01

This work presents results from a nearly two-year monitoring of the hydrologic dynamics of the largest submarine spring system in Florida, Spring Creek Springs. During the summer of 2007 this spring system was observed to have significantly reduced flow due to persistent drought conditions. Our examination of the springs revealed that the salinity of the springs' waters had increased significantly, from 4 in 2004 to 33 in July 2007 with anomalous high radon ( 222Rn, t1/2=3.8 days) in surface water concentrations indicating substantial saltwater intrusion into the local aquifer. During our investigation from August 2007 to May 2009 we deployed on an almost monthly basis a continuous radon-in-water measurement system and monitored the salinity fluctuations in the discharge area. To evaluate the springs' freshwater flux we developed three different models: two of them are based on water velocity measurements and either salinity or 222Rn in the associated surface waters as groundwater tracers. The third approach used only salinity changes within the spring area. The three models showed good agreement and the results confirmed that the hydrologic regime of the system is strongly correlated to local precipitation and water table fluctuations with higher discharges after major rain events and very low, even reverse flow during prolong droughts. High flow spring conditions were observed twice during our study, in the early spring and mid-late summer of 2008. However the freshwater spring flux during our observation period never reached that reported from a 1970s value of 4.9×10 6 m 3/day. The maximum spring flow was estimated at about 3.0×10 6 m 3/day after heavy precipitation in February-March 2008. As a result of this storm (total of 173 mm) the salinity in the spring area dropped from about 27 to 2 in only two days. The radon-in-water concentrations dramatically increased in parallel, from about 330 Bq/m 3 to about 6600 Bq/m 3. Such a rapid response suggests a direct connection between the deep and the surficial aquifers.

75 FR 69612 - Airworthiness Directives; The Boeing Company Model 747-200B, -300, -400, -400D, and -400F Series...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... loss of the spring beam load path and the possible separation of a strut and engine from the airplane... mid-pivot bolt assembly could result in the loss of the spring beam load path. Loss of the spring beam...-pivot bolt assembly, which could lead to loss of the spring beam load path and the possible separation...

Hydrogeology of northern Sierra de Chiapas, Mexico: a conceptual model based on a geochemical characterization of sulfide-rich karst brackish springs

NASA Astrophysics Data System (ADS)

Rosales Lagarde, Laura; Boston, Penelope J.; Campbell, Andrew R.; Hose, Louise D.; Axen, Gary; Stafford, Kevin W.

2014-09-01

Conspicuous sulfide-rich karst springs flow from Cretaceous carbonates in northern Sierra de Chiapas, Mexico. This is a geologically complex, tropical karst area. The physical, geologic, hydrologic and chemical attributes of these springs were determined and integrated into a conceptual hydrogeologic model. A meteoric source and a recharge elevation below 1,500 m are estimated from the spring-water isotopic signature regardless of their chemical composition. Brackish spring water flows at a maximum depth of 2,000 m, as inferred from similar chemical attributes to the produced water from a nearby oil well. Oil reservoirs may be found at depths below 2,000 m. Three subsurface environments or aquifers are identified based on the B, Li+, K+ and SiO2 concentrations, spring water temperatures, and CO2 pressures. There is mixing between these aquifers. The aquifer designated Local is shallow and contains potable water vulnerable to pollution. The aquifer named Northern receives some brackish produced water. The composition of the Southern aquifer is influenced by halite dissolution enhanced at fault detachment surfaces. Epigenic speleogenesis is associated with the Local springs. In contrast, hypogenic speleogenesis is associated with the brackish sulfidic springs from the Northern and the Southern environments.

Optimal Design of Spring Characteristics of Damper for Subharmonic Vibration in Automatic Transmission Powertrain

NASA Astrophysics Data System (ADS)

Nakae, T.; Ryu, T.; Matsuzaki, K.; Rosbi, S.; Sueoka, A.; Takikawa, Y.; Ooi, Y.

2016-09-01

In the torque converter, the damper of the lock-up clutch is used to effectively absorb the torsional vibration. The damper is designed using a piecewise-linear spring with three stiffness stages. However, a nonlinear vibration, referred to as a subharmonic vibration of order 1/2, occurred around the switching point in the piecewise-linear restoring torque characteristics because of the nonlinearity. In the present study, we analyze vibration reduction for subharmonic vibration. The model used herein includes the torque converter, the gear train, and the differential gear. The damper is modeled by a nonlinear rotational spring of the piecewise-linear spring. We focus on the optimum design of the spring characteristics of the damper in order to suppress the subharmonic vibration. A piecewise-linear spring with five stiffness stages is proposed, and the effect of the distance between switching points on the subharmonic vibration is investigated. The results of our analysis indicate that the subharmonic vibration can be suppressed by designing a damper with five stiffness stages to have a small spring constant ratio between the neighboring springs. The distances between switching points must be designed to be large enough that the amplitude of the main frequency component of the systems does not reach the neighboring switching point.

Lesser scaup winter foraging and nutrient reserve acquisition in east-central Florida

USGS Publications Warehouse

Herring, G.; Collazo, J.A.

2006-01-01

Lesser scaup (Aythya affinis) populations have been declining since the late 1970s. One of the explanations to account for this decline, the spring-condition hypothesis (SCH), is based on the premise that scaup are limited by their ability to acquire or maintain nutrient reserves during migration to the breeding grounds, leading to an impairment of their reproductive potential. Available evidence suggests that endogenous reserves required for reproduction are obtained at a later stage of migration or after arrival at the breeding grounds, not wintering sites. However, only one study has addressed body-condition levels on a southern wintering site in the last decade, with results limited to the wintering grounds on the Mississippi Flyway. We documented foraging behavior, nutrient levels, and body mass of lesser scaup in east-central Florida, USA, where 62% of the Atlantic Flyway population overwinters, during the winters of 2002 and 2003. Diurnal foraging did not increase seasonally. Nocturnal foraging increased seasonally by 76% or 43 minutes per night in females and by 478% or 1.9 hours per night in males. Measures of body condition did not change seasonally during 2002 for either sex. Between early and later winter in 2003 corrected body mass (CBM) and lipid reserves of male scaup increased 77 g and 39 g, respectively. Our results suggest that lesser scaup maintain or may slightly improve their physiological condition in east-central Florida during winter. Lower body mass and differences in nutrient levels in east-central Florida, compared to a wintering site in Louisiana, likely stem from geographic variation and lower thermal requirements associated with the warmer Florida environment. Lesser scaup depart Florida with sufficient reserves to initiate spring migration, but they maximize nutrient reserves used during reproduction elsewhere during migration or on the breeding grounds. These results suggest that maintaining the ecological integrity of this wintering ground is critical in minimizing winter mortality and preventing it from becoming an ancillary factor in current declines. Future research should address understanding survival rates during spring migration and at critical staging areas to provide new insight into the ramifications of scaup leaving wintering habitats such as MINWR with lower body condition than at other wintering sites in other flyways.

Spring-migration ecology of Northern Pintails in south-central Nebraska

USGS Publications Warehouse

Pearse, A.T.; Krapu, G.L.; Cox, R.R.; Davis, B.E.

2011-01-01

Spring-migration ecology of staging Northern Pintails, Anas acuta, was investigated in south-central Nebraska, USA. Habitat associations, local movements, settling patterns, arrival dates, residency times and survival were estimated from 71 radiomarked pintails during spring 2001, 2003 and 2004, and diet determined from 130 females collected during spring 1998 and 1999. Seventy-two percent of pintail diurnal locations were in palustrine wetlands, 7% in riverine wetlands, 3% in lacustrine wetlands, 6% in municipal sewage lagoons and irrigation reuse pits and 10.5% in croplands. Emergent wetlands with hemi-marsh conditions were used diurnally more often than wetlands with either open or closed vegetation structures. Evening foraging flights averaged 4.3 km (SE = 0.6) and 72% were to cornfields. In accord with these findings, 87% of 93 pintails collected during spring 1998 and 1999 returning to evening roosts consumed corn, which represented 84% dry mass of all foods. Pintails collected on non-cropped wetlands ingested invertebrates and seeds from wetland plants more frequently than birds returning to roost. Radiomarked pintails arrived in Nebraska on 7 March 2003 and 18 February 2004; average arrival date was six days earlier during 2004 compared to 2003. Residency time for individuals varied greatly (1-40 days) yet yearly means were similar and averaged 9.5 days within the region. No mortality was detected for 71 birds monitored over 829 exposure days. Conservation planners linking population dynamics and habitat conditions at spring-staging areas need to focus on pintail body condition during spring and its connection with reproductive success and survival during the breeding season.

Spring-migration ecology of Northern Pintails in south-central Nebraska

USGS Publications Warehouse

Pearse, Aaron T.; Krapu, Gary L.; Cox, Robert R.; Davis, Bruce E.

2011-01-01

Spring-migration ecology of staging Northern Pintails, Anas acuta, was investigated in south-central Nebraska, USA. Habitat associations, local movements, settling patterns, arrival dates, residency times and survival were estimated from 71 radiomarked pintails during spring 2001, 2003 and 2004, and diet determined from 130 females collected during spring 1998 and 1999. Seventy-two percent of pintail diurnal locations were in palustrine wetlands, 7% in riverine wetlands, 3% in lacustrine wetlands, 6% in municipal sewage lagoons and irrigation reuse pits and 10.5% in croplands. Emergent wetlands with hemi-marsh conditions were used diurnally more often than wetlands with either open or closed vegetation structures. Evening foraging flights averaged 4.3 km (SE = 0.6) and 72% were to cornfields. In accord with these findings, 87% of 93 pintails collected during spring 1998 and 1999 returning to evening roosts consumed corn, which represented 84% dry mass of all foods. Pintails collected on non-cropped wetlands ingested invertebrates and seeds from wetland plants more frequently than birds returning to roost. Radiomarked pintails arrived in Nebraska on 7 March 2003 and 18 February 2004; average arrival date was six days earlier during 2004 compared to 2003. Residency time for individuals varied greatly (1–40 days) yet yearly means were similar and averaged 9.5 days within the region. No mortality was detected for 71 birds monitored over 829 exposure days. Conservation planners linking population dynamics and habitat conditions at spring-staging areas need to focus on pintail body condition during spring and its connection with reproductive success and survival during the breeding season.

Contact analysis and experimental investigation of a linear ultrasonic motor.

PubMed

Lv, Qibao; Yao, Zhiyuan; Li, Xiang

2017-11-01

The effects of surface roughness are not considered in the traditional motor model which fails to reflect the actual contact mechanism between the stator and slider. An analytical model for calculating the tangential force of linear ultrasonic motor is proposed in this article. The presented model differs from the previous spring contact model, the asperities in contact between stator and slider are considered. The influences of preload and exciting voltage on tangential force in moving direction are analyzed. An experiment is performed to verify the feasibility of this proposed model by comparing the simulation results with the measured data. Moreover, the proposed model and spring model are compared. The results reveal that the proposed model is more accurate than spring model. The discussion is helpful for designing and modeling of linear ultrasonic motors. Copyright © 2017 Elsevier B.V. All rights reserved.

Rehabilitation of patients with thoracic spine injury treated by spring alloplasty.

PubMed

Kiwerski, J

1983-12-01

Stabilization of the traumatic injured spine by means of springs, called spring alloplasty, was introduced into clinical practice by Professor M. Weiss in 1965 and has been applied in the Warsaw Medical Academy Rehabilitation Clinic ( Konstancin ) ever since. The springs here replace the damaged system of posterior ligaments of the spine, restoring its stability and alleviating the front (often damaged) part of the body. This method has been used in surgery on about 350 patients mainly with spinal injury in the thoracic and thoracolumbar levels. Spine stabilization by the method in question usually makes it possible to start an early verticalization and an active rehabilitation. The verticalization of the patient in a specially designed bed is introduced as early as a few days after the accident, and attempts at active verticalization are made in 2-3 weeks time after surgery, thus the rehabilitation process is substantially precipitated and the period of hospital treatment is significantly reduced. The methodology of rehabilitation of the patients in question has been presented and functional effects of the treatment have been discussed in the paper.

The Electrostatic Gavimeter: An Alternative Way of Measuring Gravitational Acceleration

NASA Astrophysics Data System (ADS)

Kashinski, David

2005-03-01

In the past, Earth’s gravitational acceleration g has been measured in many ways, including the use of a pendulum as well as other models involving the use of a mass and a spring. We have designed a new method incorporating a spring with a capacitor and a voltmeter. This capacitor model still uses a hanging mass on a spring, but alters the method of determining the change in position of the spring due to the gravitational acceleration. We relate the change in position to the potential difference across the capacitor needed to cause a discharge through parallel plates. By relating this voltage directly to the gravitaional acceleration,a new method of measuring g is obtained.

Analytical approach on the stiffness of MR fluid filled spring

NASA Astrophysics Data System (ADS)

Sikulskyi, Stanislav; Kim, Daewon

2017-04-01

A solid mechanical spring generally exhibits uniform stiffness. This paper studies a mechanical spring filled with magnetorheological (MR) fluid to achieve controllable stiffness. The hollow spring filled with MR fluid is subjected to a controlled magnetic field in order to change the viscosity of the MR fluid and thereby to change the overall stiffness of the spring. MR fluid is considered as a Bingham viscoplastic linear material in the mathematical model. The goal of this research is to study the feasibility of such spring system by analytically computing the effects of MR fluid on overall spring stiffness. For this purpose, spring mechanics and MR fluid behavior are studied to increase the accuracy of the analysis. Numerical simulations are also performed to generate some assumptions, which simplify calculations in the analytical part. The accuracy of the present approach is validated by comparing the analytical results to previously known experimental results. Overall stiffness variations of the spring are also discussed for different spring designs.

Atmospheric Modeling of the Martian Polar Regions: CRISM EPF Coverage During the South Polar Spring Recession

NASA Astrophysics Data System (ADS)

Brown, A. J.; McGuire, P.; Wolff, M. J.

2008-03-01

We describe efforts to model dust and ice aerosols content and soils and icy surface reflectance in the Martian southern polar region during spring recession (Ls = 152-320) using CRISM emission phase function (EPF) observations.

NREL, San Diego Gas & Electric Are Advancing Utility Microgrid Performance

Science.gov Websites

in Borrego Springs, California | Energy Systems Integration Facility | NREL NREL, San Diego Gas & Electric Models Utility Microgrid in Borrego Springs NREL, San Diego Gas & Electric Are Advancing Utility Microgrid Performance in Borrego Springs, California San Diego Gas & Electric Company

Effect of section shape on frequencies of natural oscillations of tubular springs

NASA Astrophysics Data System (ADS)

Pirogov, S. P.; Chuba, A. Yu; Cherentsov, D. A.

2018-05-01

The necessity of determining the frequencies of natural oscillations of manometric tubular springs is substantiated. Based on the mathematical model and computer program, numerical experiments were performed that allowed us to reveal the effect of geometric parameters on the frequencies of free oscillations of manometric tubular springs.

Assessing the combined effects of climatic factors on spring wheat phenophase and grain yield in Inner Mongolia, China

PubMed Central

Pu, Feiyu; Li, Yunpeng; Xu, Jingwen; Li, Ning; Zhang, Yi; Guo, Jianping; Pan, Zhihua

2017-01-01

Understanding the regional relationships between climate change and crop production will benefit strategic decisions for future agricultural adaptation in China. In this study, the combined effects of climatic factors on spring wheat phenophase and grain yield over the past three decades in Inner Mongolia, China, were explored based on the daily climate variables from 1981–2014 and detailed observed data of spring wheat from 1981–2014. Inner Mongolia was divided into three different climate type regions, the eastern, central and western regions. The data were gathered from 10 representative agricultural meteorological experimental stations in Inner Mongolia and analysed with the Agricultural Production Systems Simulator (APSIM) model. First, the performance of the APSIM model in the spring wheat planting areas of Inner Mongolia was tested. Then, the key climatic factors limiting the phenophases and yield of spring wheat were identified. Finally, the responses of spring wheat phenophases and yield to climate change were further explored regionally. Our results revealed a general yield reduction of spring wheat in response to the pronounced climate warming from 1981 to 2014, with an average of 3564 kg·ha-1. The regional differences in yields were significant. The maximum potential yield of spring wheat was found in the western region. However, the minimum potential yield was found in the middle region. The air temperature and soil surface temperature were the optimum climatic factors that affected the key phenophases of spring wheat in Inner Mongolia. The influence of the average maximum temperature on the key phenophases of spring wheat was greater than the average minimum temperature, followed by the relative humidity and solar radiation. The most insensitive climatic factors were precipitation, wind speed and reference crop evapotranspiration. As for the yield of spring wheat, temperature, solar radiation and air relative humidity were major meteorological factors that affected in the eastern and western Inner Mongolia. Furthermore, the effect of the average minimum temperature on yield was greater than that of the average maximum temperature. The increase of temperature in the western and middle regions would reduce the spring wheat yield, while in the eastern region due to the rising temperature, the spring wheat yield increased. The increase of solar radiation in the eastern and central regions would increase the yield of spring wheat. The increased air relative humidity would make the western spring wheat yield increased and the eastern spring wheat yield decreased. Finally, the models describing combined effects of these dominant climatic factors on the maturity and yield in different regions of Inner Mongolia were used to establish geographical differences. Our findings have important implications for improving climate change impact studies and for local agricultural production to cope with ongoing climate change. PMID:29099842

Assessing the combined effects of climatic factors on spring wheat phenophase and grain yield in Inner Mongolia, China.

PubMed

Zhao, Junfang; Pu, Feiyu; Li, Yunpeng; Xu, Jingwen; Li, Ning; Zhang, Yi; Guo, Jianping; Pan, Zhihua

2017-01-01

Understanding the regional relationships between climate change and crop production will benefit strategic decisions for future agricultural adaptation in China. In this study, the combined effects of climatic factors on spring wheat phenophase and grain yield over the past three decades in Inner Mongolia, China, were explored based on the daily climate variables from 1981-2014 and detailed observed data of spring wheat from 1981-2014. Inner Mongolia was divided into three different climate type regions, the eastern, central and western regions. The data were gathered from 10 representative agricultural meteorological experimental stations in Inner Mongolia and analysed with the Agricultural Production Systems Simulator (APSIM) model. First, the performance of the APSIM model in the spring wheat planting areas of Inner Mongolia was tested. Then, the key climatic factors limiting the phenophases and yield of spring wheat were identified. Finally, the responses of spring wheat phenophases and yield to climate change were further explored regionally. Our results revealed a general yield reduction of spring wheat in response to the pronounced climate warming from 1981 to 2014, with an average of 3564 kg·ha-1. The regional differences in yields were significant. The maximum potential yield of spring wheat was found in the western region. However, the minimum potential yield was found in the middle region. The air temperature and soil surface temperature were the optimum climatic factors that affected the key phenophases of spring wheat in Inner Mongolia. The influence of the average maximum temperature on the key phenophases of spring wheat was greater than the average minimum temperature, followed by the relative humidity and solar radiation. The most insensitive climatic factors were precipitation, wind speed and reference crop evapotranspiration. As for the yield of spring wheat, temperature, solar radiation and air relative humidity were major meteorological factors that affected in the eastern and western Inner Mongolia. Furthermore, the effect of the average minimum temperature on yield was greater than that of the average maximum temperature. The increase of temperature in the western and middle regions would reduce the spring wheat yield, while in the eastern region due to the rising temperature, the spring wheat yield increased. The increase of solar radiation in the eastern and central regions would increase the yield of spring wheat. The increased air relative humidity would make the western spring wheat yield increased and the eastern spring wheat yield decreased. Finally, the models describing combined effects of these dominant climatic factors on the maturity and yield in different regions of Inner Mongolia were used to establish geographical differences. Our findings have important implications for improving climate change impact studies and for local agricultural production to cope with ongoing climate change.

SPARKy - Spring Ankle with Regenerative Kinetics to Build a New Generation of Transtibial Prostheses

DTIC Science & Technology

2010-07-01

walking on inclines/declines, and ascending/descending stairs We are able to walk continuously over ground and can walk up and down slopes and... stairs . Walking up a slope and ascending stairs needs to be improved, adding extra propulsion. The propulsion walking down stairs needs to be...bodied subjects walking on flat even surfaces, inclines/declines, and ascending/descending stairs – In Process 4. Using able bodied test data, a

Sex differences in the thermoregulation and evaporative water loss of a heterothermic bat, Lasiurus cinereus, during its spring migration

USGS Publications Warehouse

Cryan, P.M.; Wolf, B. O.

2003-01-01

This study quantifies sex differences in thermoregulation and water loss of a small (20-35 g) insectivorous heterothermic mammal, the hoary bat Lasiurus cinereus, during its spring migration. We measured body temperature, metabolic rate and evaporative water loss, and calculated wet thermal conductance, for bats exposed to air temperatures ranging from 0 to 40°C for periods of 2-5 h. Pregnant females maintained normothermic body temperatures (35.7±0.7°C; mean ± s.e.m.) independent of air temperature. In contrast, males became torpid during the majority (68%) of exposures to air temperatures <25°C. The thermal neutral zone (TNZ) ranged between approximately 30°C and 34°C in both sexes and, within the TNZ, females had lower mass-specific metabolic rates (6.1±0.2 mW g-1) than males (9.0±0.9 mW g-1). Wet thermal conductance values in torpid bats (0.7±0.5 mW g-1 deg.-1) were lower than those of normothermic individuals (1.1±0.3 mW g-1 deg.-1). Mass-specific rates of evaporative water loss in males were consistently higher than in females at most air temperatures and rates of water loss in torpid bats were 63±6% of normothermic values. These results suggest that male and pregnant female L. cinereus employ different thermoregulatory strategies during their spring migration. Females defend normothermic body temperatures, presumably to expedite embryonic growth, while males use torpor, presumably to minimize energy and water deficits. These variable thermoregulatory strategies may reflect continental differences in the summer distribution of the sexes.

Minimum daily core body temperature in western grey kangaroos decreases as summer advances: a seasonal pattern, or a direct response to water, heat or energy supply?

PubMed

Maloney, Shane K; Fuller, Andrea; Meyer, Leith C R; Kamerman, Peter R; Mitchell, Graham; Mitchell, Duncan

2011-06-01

Using implanted temperature loggers, we measured core body temperature in nine western grey kangaroos every 5 min for 24 to 98 days in spring and summer. Body temperature was highest at night and decreased rapidly early in the morning, reaching a nadir at 10:00 h, after ambient temperature and solar radiation had begun to increase. On hotter days, the minimum morning body temperature was lower than on cooler days, decreasing from a mean of 36.2°C in the spring to 34.0°C in the summer. This effect correlated better with the time of the year than with proximate thermal stressors, suggesting that either season itself or some factor correlated with season, such as food availability, caused the change. Water saving has been proposed as a selective advantage of heterothermy in other large mammals, but in kangaroos the water savings would have been small and not required in a reserve with permanent standing water. We calculate that the lower core temperature could provide energy savings of nearly 7%. It is likely that the heterothermy that we observed on hot days results either from decreased energy intake during the dry season or from a seasonal pattern entrained in the kangaroos that presumably has been selected for because of decreased energy availability during the dry season.

The Dynamic Characteristic and Hysteresis Effect of an Air Spring

NASA Astrophysics Data System (ADS)

Löcken, F.; Welsch, M.

2015-02-01

In many applications of vibration technology, especially in chassis, air springs present a common alternative to steel spring concepts. A design-independent and therefore universal approach is presented to describe the dynamic characteristic of such springs. Differential and constitutive equations based on energy balances of the enclosed volume and the mountings are given to describe the nonlinear and dynamic characteristics. Therefore all parameters can be estimated directly from physical and geometrical properties, without parameter fitting. The numerically solved equations fit very well to measurements of a passenger car air spring. In a second step a simplification of this model leads to a pure mechanical equation. While in principle the same parameters are used, just an empirical correction of the effective heat transfer coefficient is needed to handle some simplification on this topic. Finally, a linearization of this equation leads to an analogous mechanical model that can be assembled from two common spring- and one dashpot elements in a specific arrangement. This transfer into "mechanical language" enables a system description with a simple force-displacement law and a consideration of the nonobvious hysteresis and stiffness increase of an air spring from a mechanical point of view.

Thiamine and fatty acid content of Lake Michigan Chinook salmon

USGS Publications Warehouse

Honeyfield, D.C.; Peters, A.K.; Jones, M.L.

2008-01-01

Nutritional status of Lake Michigan Chinook salmon (Oncorhynchus tshawytscha) is inadequately documented. An investigation was conducted to determine muscle and liver thiamine content and whole body fatty acid composition in small, medium and large Chinook salmon. Muscle and liver thiamine concentrations were highest in small salmon, and tended to decrease with increasing fish size. Muscle thiamine was higher in fall than spring in large salmon. The high percentage of Chinook salmon (24-32% in fall and 58-71% in spring) with muscle thiamine concentration below 500 pmol/g, which has been associated with loss of equilibrium and death in other Great Lake salmonines, suggest that Chinook appear to rely less on thiamine than other Great Lakes species for which such low concentrations would be associated with thiamine deficiency (Brown et al. 2005b). A positive correlation was observed between liver total thiamine and percent liver lipids (r = 0.53, P < 0.0001, n = 119). In medium and large salmon, liver lipids were observed to be low in fish with less than 4,000 pmol/g liver total thiamine. In individuals with greater than 4,000 pmol/g liver thiamine, liver lipid increased with thiamine concentration. Individual fatty acids declined between fall and spring. Essential omega-3 fatty acids appear to be conserved as lipid content declined. Arachidonic acid (C20:4n6), an essential omega-6 fatty acid was not different between fall and spring, although the sum of omega-6 (Sw6) fatty acids declined over winter. Elevated concentrations of saturated fatty acids (sum) were observed in whole body tissue lipid. In summary, thiamine, a dietary essential vitamin, and individual fatty acids were found to vary in Lake Michigan Chinook salmon by fish size and season of the year.

Identifying taxonomic and functional surrogates for spring biodiversity conservation.

PubMed

Jyväsjärvi, Jussi; Virtanen, Risto; Ilmonen, Jari; Paasivirta, Lauri; Muotka, Timo

2018-02-27

Surrogate approaches are widely used to estimate overall taxonomic diversity for conservation planning. Surrogate taxa are frequently selected based on rarity or charisma, whereas selection through statistical modeling has been applied rarely. We used boosted-regression-tree models (BRT) fitted to biological data from 165 springs to identify bryophyte and invertebrate surrogates for taxonomic and functional diversity of boreal springs. We focused on these 2 groups because they are well known and abundant in most boreal springs. The best indicators of taxonomic versus functional diversity differed. The bryophyte Bryum weigelii and the chironomid larva Paratrichocladius skirwithensis best indicated taxonomic diversity, whereas the isopod Asellus aquaticus and the chironomid Macropelopia spp. were the best surrogates of functional diversity. In a scoring algorithm for priority-site selection, taxonomic surrogates performed only slightly better than random selection for all spring-dwelling taxa, but they were very effective in representing spring specialists, providing a distinct improvement over random solutions. However, the surrogates for taxonomic diversity represented functional diversity poorly and vice versa. When combined with cross-taxon complementarity analyses, surrogate selection based on statistical modeling provides a promising approach for identifying groundwater-dependent ecosystems of special conservation value, a key requirement of the EU Water Framework Directive. © 2018 Society for Conservation Biology.

Spring leaf phenology and the diurnal temperature range in a temperate maple forest.

PubMed

Hanes, Jonathan M

2014-03-01

Spring leaf phenology in temperate climates is intricately related to numerous aspects of the lower atmosphere [e.g., surface energy balance, carbon flux, humidity, the diurnal temperature range (DTR)]. To further develop and improve the accuracy of ecosystem and climate models, additional investigations of the specific nature of the relationships between spring leaf phenology and various ecosystem and climate processes are required in different environments. This study used visual observations of maple leaf phenology, below-canopy light intensities, and micrometeorological data collected during the spring seasons of 2008, 2009, and 2010 to examine the potential influence of leaf phenology on a seasonal transition in the trend of the DTR. The timing of a reversal in the DTR trend occurred near the time when the leaves were unfolding and expanding. The results suggest that the spring decline in the DTR can be attributed primarily to the effect of canopy closure on daily maximum temperature. These findings improve our understanding of the relationship between leaf phenology and the diurnal temperature range in temperate maple forests during the spring. They also demonstrate the necessity of incorporating accurate phenological data into ecosystem and climate models and warrant a careful examination of the extent to which canopy phenology is currently incorporated into existing models.

Nonlinear energy transport in one-dimensional lattices

NASA Astrophysics Data System (ADS)

Vuppuluri, P.; Hamilton, M.; de Alcantara Bonfim, O. F.

2007-03-01

We present a simple lattice model consisting of a one-dimensional chain, where the masses are interconnected by linear springs and allowed to move in the horizontal direction only, as in a monorail. In the transverse direction each mass is also attached to two other springs, one on each side of the mass. The ends of these springs are kept at fixed positions. The nonlinearity in the model arises from the geometric constraints imposed on the motion of the masses, as well as from the configuration of the springs. In the transverse directions the springs are either in the extended or compressed state depending on the position of the mass. Under these conditions we show that solitary waves are present in the system. In the long wavelength limit an analytical solution for these nonlinear waves is found. Numeric integrations of the equations of motion in the full system are also performed to analyze the conditions for the existence and stability of the nonlinear waves. Nonlinear supratransmission is examined and shown to exist in the model and an explanation of its mechanism is presented.

Applying spatial analysis techniques to assess the suitability of multipurpose uses of spring water in the Jiaosi Hot Spring Region, Taiwan.

PubMed

Jang, Cheng-Shin; Huang, Han-Chen

2017-07-01

The Jiaosi Hot Spring Region is one of the most famous tourism destinations in Taiwan. The spring water is processed for various uses, including irrigation, aquaculture, swimming, bathing, foot spas, and recreational tourism. Moreover, the multipurpose uses of spring water can be dictated by the temperature of the water. To evaluate the suitability of spring water for these various uses, this study spatially characterized the spring water temperatures of the Jiaosi Hot Spring Region by integrating ordinary kriging (OK), sequential Gaussian simulation (SGS), and Geographic information system (GIS). First, variogram analyses were used to determine the spatial variability of spring water temperatures. Next, OK and SGS were adopted to model the spatial uncertainty and distributions of the spring water temperatures. Finally, the land use (i.e., agriculture, dwelling, public land, and recreation) was determined using GIS and combined with the estimated distributions of the spring water temperatures. A suitable development strategy for the multipurpose uses of spring water is proposed according to the integration of the land use and spring water temperatures. The study results indicate that the integration of OK, SGS, and GIS is capable of characterizing spring water temperatures and the suitability of multipurpose uses of spring water. SGS realizations are more robust than OK estimates for characterizing spring water temperatures compared to observed data. Furthermore, current land use is almost ideal in the Jiaosi Hot Spring Region according to the estimated spatial pattern of spring water temperatures.

Water in silicate melts

NASA Astrophysics Data System (ADS)

McMillan, Paul; Stolper, Edward

Water is one of the more important volatile species in magmas, both in terms of its abundance and its influence on the properties of a given magma. Many workers in the geological sciences have measured, modeled, and speculated on the interaction of water with silicate melts as a function of pressure. At the same time, glass and materials scientists have collected a considerable body of data on the effect of water on the properties of liquid and glassy silicates at 1 atmosphere (1.01325×105 N m-2) and below. A special session on “Solubility and Transport Properties of Water in Silicate Melts” was held during the 1983 AGU Spring Meeting, May 30-June 3, in Baltimore. The session had three main objectives: (1) review the present data base and discuss the status of current models in order to identify areas where further work is needed; (2) introduce interested geologists to the large body of work being carried out in the glass and materials sciences; and (3) consider static properties, such as thermodynamic relations, structure of hydrous melts, and dynamic properties including diffusion and viscosity. This report summarizes the major topics discussed. More detailed information may be found in the published abstracts (Eos, May 3, 1983, pp. 338-343).

Bifurcation of elastic solids with sliding interfaces

NASA Astrophysics Data System (ADS)

Bigoni, D.; Bordignon, N.; Piccolroaz, A.; Stupkiewicz, S.

2018-01-01

Lubricated sliding contact between soft solids is an interesting topic in biomechanics and for the design of small-scale engineering devices. As a model of this mechanical set-up, two elastic nonlinear solids are considered jointed through a frictionless and bilateral surface, so that continuity of the normal component of the Cauchy traction holds across the surface, but the tangential component is null. Moreover, the displacement can develop only in a way that the bodies in contact do neither detach, nor overlap. Surprisingly, this finite strain problem has not been correctly formulated until now, so this formulation is the objective of the present paper. The incremental equations are shown to be non-trivial and different from previously (and erroneously) employed conditions. In particular, an exclusion condition for bifurcation is derived to show that previous formulations based on frictionless contact or `spring-type' interfacial conditions are not able to predict bifurcations in tension, while experiments-one of which, ad hoc designed, is reported-show that these bifurcations are a reality and become possible when the correct sliding interface model is used. The presented results introduce a methodology for the determination of bifurcations and instabilities occurring during lubricated sliding between soft bodies in contact.

Real-Time Interactive Tree Animation.

PubMed

Quigley, Ed; Yu, Yue; Huang, Jingwei; Lin, Winnie; Fedkiw, Ronald

2018-05-01

We present a novel method for posing and animating botanical tree models interactively in real time. Unlike other state of the art methods which tend to produce trees that are overly flexible, bending and deforming as if they were underwater plants, our approach allows for arbitrarily high stiffness while still maintaining real-time frame rates without spurious artifacts, even on quite large trees with over ten thousand branches. This is accomplished by using an articulated rigid body model with as-stiff-as-desired rotational springs in conjunction with our newly proposed simulation technique, which is motivated both by position based dynamics and the typical algorithms for articulated rigid bodies. The efficiency of our algorithm allows us to pose and animate trees with millions of branches or alternatively simulate a small forest comprised of many highly detailed trees. Even using only a single CPU core, we can simulate ten thousand branches in real time while still maintaining quite crisp user interactivity. This has allowed us to incorporate our framework into a commodity game engine to run interactively even on a low-budget tablet. We show that our method is amenable to the incorporation of a large variety of desirable effects such as wind, leaves, fictitious forces, collisions, fracture, etc.

An analytic model for accurate spring constant calibration of rectangular atomic force microscope cantilevers.

PubMed

Li, Rui; Ye, Hongfei; Zhang, Weisheng; Ma, Guojun; Su, Yewang

2015-10-29

Spring constant calibration of the atomic force microscope (AFM) cantilever is of fundamental importance for quantifying the force between the AFM cantilever tip and the sample. The calibration within the framework of thin plate theory undoubtedly has a higher accuracy and broader scope than that within the well-established beam theory. However, thin plate theory-based accurate analytic determination of the constant has been perceived as an extremely difficult issue. In this paper, we implement the thin plate theory-based analytic modeling for the static behavior of rectangular AFM cantilevers, which reveals that the three-dimensional effect and Poisson effect play important roles in accurate determination of the spring constants. A quantitative scaling law is found that the normalized spring constant depends only on the Poisson's ratio, normalized dimension and normalized load coordinate. Both the literature and our refined finite element model validate the present results. The developed model is expected to serve as the benchmark for accurate calibration of rectangular AFM cantilevers.

Simulation of spring discharge from a limestone aquifer in Iowa, USA

USGS Publications Warehouse

Zhang, Y.-K.; Bai, E.-W.; Libra, R.; Rowden, R.; Liu, H.

1996-01-01

A lumped-parameter model and least-squares method were used to simulate temporal variations of discharge from Big Spring, Iowa, USA, from 1983 to 1994. The simulated discharge rates poorly match the observed one when precipitation is taken as the sole input. The match is improved significantly when the processes of evapotranspiration and infiltration are considered. The best results are obtained when snowmelt is also included in the model. Potential evapotranspiration was estimated with Thornthwaite's formula, infiltration was calculated through a water-balance approach, and snowmelt was generated by a degree-day model. The results show that groundwater in the limestone aquifer is mainly recharged by snowmelt in early spring and by infiltration from rainfall in later spring and early summer. Simulated discharge was visually calibrated against measured discharge; the similarity between the two supports the validity of this approach. The model can be used to study the effects of climate change on groundwater resources and their quality.

Monitoring growth condition of spring maize in Northeast China using a process-based model

NASA Astrophysics Data System (ADS)

Wang, Peijuan; Zhou, Yuyu; Huo, Zhiguo; Han, Lijuan; Qiu, Jianxiu; Tan, Yanjng; Liu, Dan

2018-04-01

Early and accurate assessment of the growth condition of spring maize, a major crop in China, is important for the national food security. This study used a process-based Remote-Sensing-Photosynthesis-Yield Estimation for Crops (RS-P-YEC) model, driven by satellite-derived leaf area index and ground-based meteorological observations, to simulate net primary productivity (NPP) of spring maize in Northeast China from the first ten-day (FTD) of May to the second ten-day (STD) of August during 2001-2014. The growth condition of spring maize in 2014 in Northeast China was monitored and evaluated spatially and temporally by comparison with 5- and 13-year averages, as well as 2009 and 2013. Results showed that NPP simulated by the RS-P-YEC model, with consideration of multi-scattered radiation inside the crop canopy, could reveal the growth condition of spring maize more reasonably than the Boreal Ecosystem Productivity Simulator. Moreover, NPP outperformed other commonly used vegetation indices (e.g., Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI)) for monitoring and evaluating the growth condition of spring maize. Compared with the 5- and 13-year averages, the growth condition of spring maize in 2014 was worse before the STD of June and after the FTD of August, and it was better from the third ten-day (TTD) of June to the TTD of July across Northeast China. Spatially, regions with slightly worse and worse growth conditions in the STD of August 2014 were concentrated mainly in central Northeast China, and they accounted for about half of the production area of spring maize in Northeast China. This study confirms that NPP is a good indicator for monitoring and evaluating growth condition because of its capacity to reflect the physiological characteristics of crops. Meanwhile, the RS-P-YEC model, driven by remote sensing and ground-based meteorological data, is effective for monitoring crop growth condition over large areas in a near real time.

Predicting ground-water movement in large mine spoil areas in the Appalachian Plateau

USGS Publications Warehouse

Wunsch, D.R.; Dinger, J.S.; Graham, C.D.R.

1999-01-01

Spoil created by surface mining can accumulate large quantities of ground-water, which can create geotechnical or regulatory problems, as well as flood active mine pits. A current study at a large (4.1 km2), thick, (up to 90 m) spoil body in eastern Kentucky reveals important factors that control the storage and movement of water. Ground-water recharge occurs along the periphery of the spoil body where surface-water drainage is blocked, as well as from infiltration along the spoil-bedrock contact, recharge from adjacent bedrock, and to a minor extent, through macropores at the spoil's surface. Based on an average saturated thickness of 6.4 m for all spoil wells, and assuming an estimated porosity of 20%, approximately 5.2 x 106 m3 of water is stored within the existing 4.1 km2 of reclaimed spoil. A conceptual model of ground-water flow, based on data from monitoring wells, dye-tracing data, discharge from springs and ponds, hydraulic gradients, chemical data, field reconnaissance, and aerial photographs indicate that three distinct but interconnected saturated zones have been established: one in the spoil's interior, and others in the valley fills that surround the main spoil body at lower elevations. Ground-water movement is sluggish in the spoil's interior, but moves quickly through the valley fills. The conceptual model shows that a prediction of ground-water occurrence, movement, and quality can be made for active or abandoned spoil areas if all or some of the following data are available: structural contour of the base of the lowest coal seam being mined, pre-mining topography, documentation of mining methods employed throughout the mine, overburden characteristics, and aerial photographs of mine progression.Spoil created by surface mining can accumulate large quantities of ground-water, which can create geotechnical or regulatory problems, as well as flood active mine pits. A current study at a large (4.1 km2), thick, (up to 90 m) spoil body in eastern Kentucky reveals important factors that control the storage and movement of water. Ground-water recharge occurs along the periphery of the spoil body where surface-water drainage is blocked, as well as from infiltration along the spoil-bedrock contact, recharge from adjacent bedrock, and to a minor extent, through macropores at the spoil's surface. Based on an average saturated thickness of 6.4 m for all spoil wells, and assuming an estimated porosity of 20%, approximately 5.2 ?? 106 m3 of water is stored within the existing 4.1 km2 of reclaimed spoil. A conceptual model of ground-water flow, based on data from monitoring wells, dye-tracing data, discharge from springs and ponds, hydraulic gradients, chemical data, field reconnaissance, and aerial photographs indicate that three distinct but interconnected saturated zones have been established: one in the spoil's interior, and others in the valley fills that surround the main spoil body at lower elevations. Ground-water movement is sluggish in the spoil's interior, but moves quickly through the valley fills. The conceptual model shows that a prediction of ground-water occurrence, movement, and quality can be made for active or abandoned spoil areas if all or some of the following data are available: structural contour of the base of the lowest coal seam being mined, pre-mining topography, documentation of mining methods employed throughout the mine, overburden characteristics, and aerial photographs of mine progression.

Age and source of water in springs associated with the Jacksonville Thrust Fault Complex, Calhoun County, Alabama

USGS Publications Warehouse

Robinson, James L.

2004-01-01

Water from wells and springs accounts for more than 90 percent of the public water supply in Calhoun County, Alabama. Springs associated with the Jacksonville Thrust Fault Complex are used for public water supply for the cities of Anniston and Jacksonville. The largest ground-water supply is Coldwater Spring, the primary source of water for Anniston, Alabama. The average discharge of Coldwater Spring is about 32 million gallons per day, and the variability of discharge is about 75 percent. Water-quality samples were collected from 6 springs and 15 wells in Calhoun County from November 2001 to January 2003. The pH of the ground water typically was greater than 6.0, and specific conductance was less than 300 microsiemens per centimeter. The water chemistry was dominated by calcium, carbonate, and bicarbonate ions. The hydrogen and oxygen isotopic composition of the water samples indicates the occurrence of a low-temperature, water-rock weathering reaction known as silicate hydrolysis. The residence time of the ground water, or ground-water age, was estimated by using analysis of chlorofluorocarbon, sulfur hexafluoride, and regression modeling. Estimated ground-water ages ranged from less than 10 to approximately 40 years, with a median age of about 18 years. The Spearman rho test was used to identify statistically significant covariance among selected physical properties and constituents in the ground water. The alkalinity, specific conductance, and dissolved solids increased as age increased; these correlations reflect common changes in ground-water quality that occur with increasing residence time and support the accuracy of the age estimates. The concentration of sodium and chloride increased as age increased; the correlation of these constituents is interpreted to indicate natural sources for chloride and sodium. The concentration of silica increased as the concentration of potassium increased; this correlation, in addition to the isotopic data, is evidence that silicate hydrolysis of clay minerals occurred. The geochemical modeling program NETPATH was used to investigate possible mixing scenarios that could yield the chemical composition of water collected from springs associated with the Jacksonville Thrust Fault Complex. The results of NETPATH modeling suggest that the primary source of water in Coldwater Spring is a deep aquifer, and only small amounts of rainwater from nearby sources are discharged from the spring. Starting with Piedmont Sports Spring and moving southwest along a conceptual ground-water flow path that parallels the Jacksonville Thrust Fault Complex, NETPATH simulated the observed water quality of each spring, in succession, by mixing rainwater and water from the spring just to the northeast of the spring being modeled. The percentage of rainwater and ground water needed to simulate the quality of water flowing from the springs ranged from 1 to 25 percent rainwater and 75 to 99 percent ground water.

Description and Evaluation of Numerical Groundwater Flow Models for the Edwards Aquifer, South-Central Texas

USGS Publications Warehouse

Lindgren, Richard J.; Taylor, Charles J.; Houston, Natalie A.

2009-01-01

A substantial number of public water system wells in south-central Texas withdraw groundwater from the karstic, highly productive Edwards aquifer. However, the use of numerical groundwater flow models to aid in the delineation of contributing areas for public water system wells in the Edwards aquifer is problematic because of the complex hydrogeologic framework and the presence of conduit-dominated flow paths in the aquifer. The U.S. Geological Survey, in cooperation with the Texas Commission on Environmental Quality, evaluated six published numerical groundwater flow models (all deterministic) that have been developed for the Edwards aquifer San Antonio segment or Barton Springs segment, or both. This report describes the models developed and evaluates each with respect to accessibility and ease of use, range of conditions simulated, accuracy of simulations, agreement with dye-tracer tests, and limitations of the models. These models are (1) GWSIM model of the San Antonio segment, a FORTRAN computer-model code that pre-dates the development of MODFLOW; (2) MODFLOW conduit-flow model of San Antonio and Barton Springs segments; (3) MODFLOW diffuse-flow model of San Antonio and Barton Springs segments; (4) MODFLOW Groundwater Availability Modeling [GAM] model of the Barton Springs segment; (5) MODFLOW recalibrated GAM model of the Barton Springs segment; and (6) MODFLOW-DCM (dual conductivity model) conduit model of the Barton Springs segment. The GWSIM model code is not commercially available, is limited in its application to the San Antonio segment of the Edwards aquifer, and lacks the ability of MODFLOW to easily incorporate newly developed processes and packages to better simulate hydrologic processes. MODFLOW is a widely used and tested code for numerical modeling of groundwater flow, is well documented, and is in the public domain. These attributes make MODFLOW a preferred code with regard to accessibility and ease of use. The MODFLOW conduit-flow model incorporates improvements over previous models by using (1) a user-friendly interface, (2) updated computer codes (MODFLOW-96 and MODFLOW-2000), (3) a finer grid resolution, (4) less-restrictive boundary conditions, (5) an improved discretization of hydraulic conductivity, (6) more accurate estimates of pumping stresses, (7) a long transient simulation period (54 years, 1947-2000), and (8) a refined representation of high-permeability zones or conduits. All of the models except the MODFLOW-DCM conduit model have limitations resulting from the use of Darcy's law to simulate groundwater flow in a karst aquifer system where non-Darcian, turbulent flow might actually dominate. The MODFLOW-DCM conduit model is an improvement in the ability to simulate karst-like flow conditions in conjunction with porous-media-type matrix flow. However, the MODFLOW-DCM conduit model has had limited application and testing and currently (2008) lacks commercially available pre- and post-processors. The MODFLOW conduit-flow and diffuse-flow Edwards aquifer models are limited by the lack of calibration for the northern part of the Barton Springs segment (Travis County) and their reliance on the use of the calibrated hydraulic conductivity and storativity values from the calibrated Barton Springs segment GAM model. The major limitation of the Barton Springs segment GAM and recalibrated GAM models is that they were calibrated to match measured water levels and springflows for a restrictive range of hydrologic conditions, with each model having different hydraulic conductivity and storativity values appropriate to the hydrologic conditions that were simulated. The need for two different sets of hydraulic conductivity and storativity values increases the uncertainty associated with the accuracy of either set of values, illustrates the non-uniqueness of the model solution, and probably most importantly demonstrates the limitations of using a one-layer model to represent the heterogeneous hydrostratigraph

Acute Compartment Syndrome of the Thigh in Combat Casualties

DTIC Science & Technology

2013-03-01

Orthopaedic Association VOLUME 22, NUMBER 1, SPRING 2013 45 incisions were closed primarily, six with skin graft , and one by secondary intention. Discussion...With skin graft (skin from another part of your body) Y / N comment _________________ By Secondary intention (daily dressing changes to

A Harmonic Motion Experiment

ERIC Educational Resources Information Center

Gluck, P.; Krakower, Zeev

2010-01-01

We present a unit comprising theory, simulation and experiment for a body oscillating on a vertical spring, in which the simultaneous use of a force probe and an ultrasonic range finder enables one to explore quantitatively and understand many aspects of simple and damped harmonic motions. (Contains 14 figures.)

The Meteoroid Fluence at Mars Due to Comet C/2013 A1 (Siding Spring)

NASA Technical Reports Server (NTRS)

Moorhead, A.; Wiegert, P.; Blaauw, R.; McCarty, C.; Kingery, A.; Cooke, W.

2014-01-01

Long-period comet C/2013 A1 (Siding Spring) will experience a close encounter with Mars on 2014 Oct 19. A collision between the comet and the planet has been ruled out, but the comet's coma may envelop Mars and its man-made satellites. By the time of the close encounter, five operational spacecraft will be present near Mars. Characterizing the coma is crucial for assessing the risk posed to these satellites by meteoroid impacts. We present an analytic model of cometary comae that describes the spatial and size distributions of cometary dust and meteoroids. This model correctly reproduces, to within an order of magnitude, the number of impacts recorded by Giotto near 1P/Halley [1] and by Stardust near comet 81P/Wild 2 [2]. Applied to Siding Spring, our model predicts a total particle fluence near Mars of 0.02 particles per square meter. In order to determine the degree to which Siding Spring's coma deviates from a sphere, we perform numerical simulations which take into account both gravitational effects and radiative forces. We take the entire dust component of the coma and tail continuum into account by simulating the ejection and evolution of dust particles from comet Siding Spring. The total number of particles simulated is essentially a free parameter and does not provide a check on the total fluence. Instead, these simulations illustrate the degree to which the coma of Siding Spring deviates from the perfect sphere described by our analytic model (see Figure). We conclude that our analytic model sacrifices less than an order of magnitude in accuracy by neglecting particle dynamics and radiation pressure and is thus adequate for order-of-magnitude fluence estimates. Comet properties may change unpredictably and therefore an analytic coma model that enables quick recalculation of the meteoroid fluence is highly desirable. NASA's Meteoroid Environment Office is monitoring comet Siding Spring and taking measurements of cometary brightness and dust production. We will discuss our coma model and nominal fluence taking the latest observations into account.

Constitutive Modeling of Porcine Liver in Indentation Using 3D Ultrasound Imaging

PubMed Central

Jordan, P.; Socrate, S.; Zickler, T.E.; Howe, R.D.

2009-01-01

In this work we present an inverse finite-element modeling framework for constitutive modeling and parameter estimation of soft tissues using full-field volumetric deformation data obtained from 3D ultrasound. The finite-element model is coupled to full-field visual measurements by regularization springs attached at nodal locations. The free ends of the springs are displaced according to the locally estimated tissue motion and the normalized potential energy stored in all springs serves as a measure of model-experiment agreement for material parameter optimization. We demonstrate good accuracy of estimated parameters and consistent convergence properties on synthetically generated data. We present constitutive model selection and parameter estimation for perfused porcine liver in indentation and demonstrate that a quasilinear viscoelastic model with shear modulus relaxation offers good model-experiment agreement in terms of indenter displacement (0.19 mm RMS error) and tissue displacement field (0.97 mm RMS error). PMID:19627823

Water quality parameters associated with prevalence of Legionella in hot spring facility water bodies.

PubMed

Huang, Shih-Wei; Hsu, Bing-Mu; Wu, Shu-Fen; Fan, Cheng-Wei; Shih, Feng-Cheng; Lin, Yung-Chang; Ji, Dar-Der

2010-09-01

Some species of Legionella are recognized as opportunistic potential human pathogens, such as Legionella pneumophila, which causes legionnaires disease. Indeed, outbreaks of legionellosis are frequently reported in areas in which the organism has been spread via aerosols from contaminated institutional water systems. Contamination in hot tubs, spas and public baths are also possible. As a result, in this study, we investigated the distribution of Legionella at six hot spring recreation areas throughout Taiwan. Legionella were detected in all six hot spring recreation areas, as well as in 20 of the 72 samples that were collected (27.8%). Seven species of Legionella identified from samples by the direct DNA extraction method were unidentified Legionella spp., Legionella anisa, L. pneumophila, Legionella erythra, Legionella lytica, Legionella gresilensis and Legionella rubrilucen. Three species of Legionella identified in the samples using the culture method were L. pneumophila, unidentified Legionella spp. and L. erythra. Legionella species were found in water with temperatures ranging from 22.7 °C to 48.6 °C. The optimal pH appeared to range from 5.0 to 8.0. Taken together, the results of this survey confirmed the ubiquity of Legionella in Taiwan spring recreational areas. Therefore, a long-term investigation of the health of workers at hot spring recreational areas and the occurrence of Legionella in hot spring recreational areas throughout Taiwan are needed. Copyright © 2010 Elsevier Ltd. All rights reserved.

The role of tributary mixing in chemical variations at a karst spring, Milandre, Switzerland

NASA Astrophysics Data System (ADS)

Perrin, J.; Jeannin, P.-Y.; Cornaton, F.

2007-01-01

SummarySolute concentration variations during flood events were investigated in a karst aquifer of the Swiss Jura. Observations were made at the spring, and at the three main subterraneous tributaries feeding the spring. A simple transient flow and transport numerical model was able to reproduce chemographs and hydrographs observed at the spring, as a result of a mixing of the concentration and discharge of the respective tributaries. Sensitivity analysis carried out with the model showed that it is possible to produce chemical variations at the spring even if all tributaries have constant (but different for each of them) solute concentrations. This process is called tributary mixing. The good match between observed and modelled curves indicate that, in the phreatic zone, tributary mixing is probably an important process that shapes spring chemographs. Chemical reactions and other mixing components (e.g. from low permeability volumes) have a limited influence. Dissolution-related (calcium, bicarbonate, specific conductance) and pollution-related parameters (nitrate, chloride, potassium) displayed slightly different behaviours: during moderate flood events, the former showed limited variations compared to the latter. During large flood events, both presented chemographs with significant changes. No significant event water participates in moderate flood events and tributary mixing will be the major process shaping chemographs. Variations are greater for parameters with higher spatial variability (e.g. pollution-related). Whereas for large flood events, the contribution of event water becomes significant and influences the chemographs of all the parameters. As a result, spring water vulnerability to an accidental pollution is low during moderate flood events and under base flow conditions. It strongly increases during large flood events, because event water contributes to the spring discharge.

An observation-based progression modeling approach to spring and autumn deciduous tree phenology

NASA Astrophysics Data System (ADS)

Yu, Rong; Schwartz, Mark D.; Donnelly, Alison; Liang, Liang

2016-03-01

It is important to accurately determine the response of spring and autumn phenology to climate change in forest ecosystems, as phenological variations affect carbon balance, forest productivity, and biodiversity. We observed phenology intensively throughout spring and autumn in a temperate deciduous woodlot at Milwaukee, WI, USA, during 2007-2012. Twenty-four phenophase levels in spring and eight in autumn were recorded for 106 trees, including white ash, basswood, white oak, boxelder, red oak, and hophornbeam. Our phenological progression models revealed that accumulated degree-days and day length explained 87.9-93.4 % of the variation in spring canopy development and 75.8-89.1 % of the variation in autumn senescence. In addition, the timing of community-level spring and autumn phenophases and the length of the growing season from 1871 to 2012 were reconstructed with the models developed. All simulated spring phenophases significantly advanced at a rate from 0.24 to 0.48 days/decade ( p ≤ 0.001) during the 1871-2012 period and from 1.58 to 2.00 days/decade ( p < 0.02) during the 1970-2012 period; two simulated autumn phenophases were significantly delayed at a rate of 0.37 (mid-leaf coloration) and 0.50 (full-leaf coloration) days/decade ( p < 0.01) during the 1970-2012 period. Consequently, the simulated growing season lengthened at a rate of 0.45 and 2.50 days/decade ( p < =0.001), respectively, during the two periods. Our results further showed the variability of responses to climate between early and late spring phenophases, as well as between leaf coloration and leaf fall, and suggested accelerating simulated ecosystem responses to climate warming over the last four decades in comparison to the past 142 years.

An observation-based progression modeling approach to spring and autumn deciduous tree phenology.

PubMed

Yu, Rong; Schwartz, Mark D; Donnelly, Alison; Liang, Liang

2016-03-01

It is important to accurately determine the response of spring and autumn phenology to climate change in forest ecosystems, as phenological variations affect carbon balance, forest productivity, and biodiversity. We observed phenology intensively throughout spring and autumn in a temperate deciduous woodlot at Milwaukee, WI, USA, during 2007-2012. Twenty-four phenophase levels in spring and eight in autumn were recorded for 106 trees, including white ash, basswood, white oak, boxelder, red oak, and hophornbeam. Our phenological progression models revealed that accumulated degree-days and day length explained 87.9-93.4 % of the variation in spring canopy development and 75.8-89.1 % of the variation in autumn senescence. In addition, the timing of community-level spring and autumn phenophases and the length of the growing season from 1871 to 2012 were reconstructed with the models developed. All simulated spring phenophases significantly advanced at a rate from 0.24 to 0.48 days/decade (p ≤ 0.001) during the 1871-2012 period and from 1.58 to 2.00 days/decade (p < 0.02) during the 1970-2012 period; two simulated autumn phenophases were significantly delayed at a rate of 0.37 (mid-leaf coloration) and 0.50 (full-leaf coloration) days/decade (p < 0.01) during the 1970-2012 period. Consequently, the simulated growing season lengthened at a rate of 0.45 and 2.50 days/decade (p < =0.001), respectively, during the two periods. Our results further showed the variability of responses to climate between early and late spring phenophases, as well as between leaf coloration and leaf fall, and suggested accelerating simulated ecosystem responses to climate warming over the last four decades in comparison to the past 142 years.

LACIE: Wheat yield models for the United States, revision A

NASA Technical Reports Server (NTRS)

1977-01-01

For abstract, see volume 1 N77-30577. The enclosed maps indicate the areal coverage of the various models for spring (durum and other spring) and winter wheat. The given regions are the combination of several climatic divisions and many times comprise an entire state.

The identification of sustainable yield for hot spring regarding water level and temperature

NASA Astrophysics Data System (ADS)

Ke, Kai-Yuan; Tan, Yih-Chi

2017-04-01

In order to sustainably manage and utilize the limited hot spring resource, the cool-hot water exchange model is established by combination of Soil and Water Assessment Tool(SWAT) and SHEMAT. Hot spring in Ziaoxi, Taiwan, is chosen as study area. With data of geography, weather, land use and soil texture, SWAT can simulate precipitation induced infiltration and recharge for SHEMAT. Then SHEMAT is calibrated and verified with in-situ observation data of hot spring temperature and water level. The relation among precipitation, pumping, change of water temperature and water level is thus investigated. The effect of point well pumping, which dramatically lower the water level and temperature, due to prosperous development of hot spring building and industry is also considered for better model calibration. In addition, by employing a modified Hill's method, the sustainable yield is identified. Unlike traditional Hill's method, the modified Hill's method could account for not only the change of water level but also the temperature. As a result, the estimated sustainable yield provide a reasonable availability of hot spring resources without further decline of the water level and temperature.

How important is exact knowledge of preferential flowpath locations and orientations for understanding spatiotemporally integrated spring hydrologic and transport response?

NASA Astrophysics Data System (ADS)

Henson, W.; De Rooij, R.; Graham, W. D.

2016-12-01

The Upper Floridian Aquifer is hydrogeologically complex; limestone dissolution has led to vertical and horizontal preferential flow paths. Locations of karst conduits are unknown and conduit properties are poorly constrained. Uncertainty in effects of conduit location, size, and density, network geometry and connectivity on hydrologic and transport responses is not well quantified, leading to limited use of discrete-continuum models that incorporate conduit networks for regional-scale hydrologic regulatory models. However, conduit networks typically dominate flow and contaminant transport in karst aquifers. We evaluated sensitivity of simulated water and nitrate fluxes and flow paths to karst conduit geometry in a springshed representative of Silver Springs, Florida, using a novel calcite dissolution conduit-generation algorithm coupled with a discrete-continuum flow and transport model (DisCo). Monte Carlo simulations of conduit generation, groundwater flow, and conservative solute transport indicate that, if a first magnitude spring system conduit network developed (i.e., spring flow >2.8 m3/s), the uncertainty in hydraulic and solute pulse response metrics at the spring vent was minimally related to locational uncertainty of network elements. Across the ensemble of realizations for various distributions of conduits, first magnitude spring hydraulic pulse metrics (e.g., steady-flow, peak flow, and recession coefficients) had < 0.01 coefficient of variation (CV). Similarly, spring solute breakthrough curve moments had low CV (<0.08); peak arrival had CV=0.06, mean travel time had CV=0.05, and travel time standard deviation had CV=0.08. Nevertheless, hydraulic and solute pulse response metrics were significantly different than those predicted by an equivalent porous-media model. These findings indicate that regional-scale decision models that incorporate karst preferential flow paths within an uncertainty framework can be used to better constrain aquifer-vulnerability estimates, despite lacking information about actual conduit locations.

Maintenance of equilibrium point control during an unexpectedly loaded rapid limb movement.

PubMed

Simmons, R W; Richardson, C

1984-06-08

Two experiments investigated whether the equilibrium point hypothesis or the mass-spring model of motor control subserves positioning accuracy during spring loaded, rapid, bi-articulated movement. For intact preparations, the equilibrium point hypothesis predicts response accuracy to be determined by a mixture of afferent and efferent information, whereas the mass-spring model predicts positioning to be under a direct control system. Subjects completed a series of load-resisted training trials to a spatial target. The magnitude of a sustained spring load was unexpectedly increased on selected trials. Results indicated positioning accuracy and applied force varied with increases in load, which suggests that the original efferent commands are modified by afferent information during the movement as predicted by the equilibrium point hypothesis.

Estimation of deepwater temperature and hydrogeochemistry of springs in the Takab geothermal field, West Azerbaijan, Iran.

PubMed

Sharifi, Reza; Moore, Farid; Mohammadi, Zargham; Keshavarzi, Behnam

2016-01-01

Chemical analyses of water samples from 19 hot and cold springs are used to characterize Takab geothermal field, west of Iran. The springs are divided into two main groups based on temperature, host rock, total dissolved solids (TDS), and major and minor elements. TDS, electrical conductivity (EC), Cl(-), and SO4 (2-) concentrations of hot springs are all higher than in cold springs. Higher TDS in hot springs probably reflect longer circulation and residence time. The high Si, B, and Sr contents in thermal waters are probably the result of extended water-rock interaction and reflect flow paths and residence time. Binary, ternary, and Giggenbach diagrams were used to understand the deeper mixing conditions and locations of springs in the model system. It is believed that the springs are heated either by mixing of deep geothermal fluid with cold groundwater or low conductive heat flow. Mixing ratios are evaluated using Cl, Na, and B concentrations and a mass balance approach. Calculated quartz and chalcedony geothermometer give lower reservoir temperatures than cation geothermometers. The silica-enthalpy mixing model predicts a subsurface reservoir temperature between 62 and 90 °C. The δ(18)O and δD (δ(2)H) are used to trace and determine the origin and movement of water. Both hot and cold waters plot close to the local meteoric line, indicating local meteoric origin.

Spring plant phenology and false springs in the conterminous US during the 21st century

USGS Publications Warehouse

Allstadt, Andrew J.; Vavrus, Stephen J.; Heglund, Patricia J.; Pidgeon, Anna M.; Thogmartin, Wayne E.; Radeloff, Volker C.

2015-01-01

The onset of spring plant growth has shifted earlier in the year over the past several decades due to rising global temperatures. Earlier spring onset may cause phenological mismatches between the availability of plant resources and dependent animals, and potentially lead to more false springs, when subsequent freezing temperatures damage new plant growth. We used the extended spring indices to project changes in spring onset, defined by leaf out and by first bloom, and predicted false springs until 2100 in the conterminous United States (US) using statistically-downscaled climate projections from the Coupled Model Intercomparison Project 5 ensemble. Averaged over our study region, the median shift in spring onset was 23 days earlier in the Representative Concentration Pathway 8.5 scenario with particularly large shifts in the Western US and the Great Plains. Spatial variation in phenology was due to the influence of short-term temperature changes around the time of spring onset versus season long accumulation of warm temperatures. False spring risk increased in the Great Plains and portions of the Midwest, but remained constant or decreased elsewhere. We conclude that global climate change may have complex and spatially variable effects on spring onset and false springs, making local predictions of change difficult.

[Long-term dynamic of fecal corticosterone and its ecological and social correlates in males of great gerbil (Rhombomys opimus Licht.). Non-invasive approach in studies of stress in natural populations].

PubMed

Rogovin, K A; Tupikin, A A; Randall, J A; Kolosova, I E; Moshkin, M P

2006-01-01

The relationship between fecal corticosterone concentrations and characteristics of the environment and population demography were studied in adult male gerbils (Rhombomys opimus Licht.) at the southern border of Kyzylkum desert (Reserve "Ecocentre Dzeiran", Bukhara region, Republic Uzbekistan) in spring and fall seasons from 1999 to 2004. We extracted hormones from air-dried fecal samples and analyzed their concentrations by radioimmunoassay (Gerlinskaya et al., 1993). An analysis for year-specific relationships between hormone concentrations and environmental variables of temperature and precipitation using Pearson's r statistic revealed that corticosterone concentrations correlated positively with total precipitation in January and February and negatively with precipitation during March and April. There was also a significant negative relationship between fecal corticosterone and the number of hot days in March (>20 degrees C). Demographic variables that characterized population densities (percent of burrow systems occupied, mean and maximum number of burrow systems/1 ha, number of females in the burrow system) correlated positively with corticosterone concentrations in feces in the beginning of spring, but these relationships were small compared with mean concentrations of corticosterone for the entire spring season that were strongly and positively correlated with number of gerbils, including all pups emerged, in burrow systems owned by one male (within its home range). In contrast, correlation coefficients of corticosterone concentrations with characteristics of feeding resources in the spring were low and negative. In the long-term perspective (interannual comparison), mortality among adult males was highly negatively correlated with mean corticosterone concentrations in the beginning of spring, which is within the period of maximum reproductive effort and potential stress. Body mass was independent of corticosterone concentrations in males in either the beginning of spring, or during the whole spring. In the fall, mean concentrations of fecal corticosterone in males was positively correlated with the number of days from June to October with mean daily temperatures exceeding 30 degrees C, and with percent of burrow systems where at least one adult, > or = 1 year old gerbil had survived. Mortality from fall to spring of the next year and the fall body mass did not correlate with concentrations of corticosterone in feces collected in the fall. When we analyzed corticosterone concentrations in spring seasons of all years combined using a stepwise regression analysis of a sampling of individual males (we analyzed residuals after withdrawal of year effect) on a set of variables representing habitat resources, distances between nearest neighbor males, and variables representing group demography we found low R2 values not exceeding 0.17. Within the six-year period, concentrations of corticosterone in the spring related negatively with abundance of annual herbs and positively with number of females in a male's social group. When only years of high density were analyzed, fecal corticosterone concentrations in males in the spring were again negatively determined by abundance of herbs, as well as by the nearest neighbor distance, and positively determined by the number of females within a male's home range. At the beginning of spring the only determinants were distance to the nearest neighbor male and number of females. In years of low density none of the variables were found to affect corticosterone levels during the whole spring, while in the beginning of spring only partial regression coefficients of abundance of herbs were negative and significant. Stepwise logistic regression analysis revealed positive dependence (P = 0.05) of disappearance of adult males during summer drought on concentrations of fecal corticosterone in the spring, but only when burrow systems with at least one adult (male or female) surviving after the summer were considered. Our results provide evidence ground for the assumption that in a desert rodent with non-regular population fluctuations such as the great gerbil, density may be more suppressed by external factors and not by density dependent mortality mediated by stress. Density dependent increases of stress caused by intense reproductive effort occurred when feeding and climatic conditions were favorable to compensate for negative effects on survival. However, in individual gerbils mortality mediated by stress can take place because we found higher stress in the beginning of spring in males, which did not occur in the population after the summer drought.

Simulation of climatology and Interannual Variability of Spring Persistent Rains by Meteorological Research Institute Model: Impacts of different horizontal resolutions

NASA Astrophysics Data System (ADS)

Li, Puxi; Zhou, Tianjun; Zou, Liwei

2016-04-01

The authors evaluated the performance of Meteorological Research Institute (MRI) AGCM3.2 models in the simulations of climatology and interannual variability of the Spring Persistent Rains (SPR) over southeastern China. The possible impacts of different horizontal resolutions were also investigated based on the experiments with three different horizontal resolutions (i.e., 120, 60, and 20km). The model could reasonably reproduce the main rainfall center over southeastern China in boreal spring under the three different resolutions. In comparison with 120 simulation, it revealed that 60km and 20km simulations show the superiority in simulating rainfall centers anchored by the Nanling-Wuyi Mountains, but overestimate rainfall intensity. Water vapor budget diagnosis showed that, the 60km and 20km simulations tended to overestimate the water vapor convergence over southeastern China, which leads to wet biases. In the aspect of interannual variability of SPR, the model could reasonably reproduce the anomalous lower-tropospheric anticyclone in the western North Pacific (WNPAC) and positive precipitation anomalies over southeastern China in El Niño decaying spring. Compared with the 120km resolution, the large positive biases are substantially reduced in the mid and high resolution models which evidently improve the simulation of horizontal moisture advection in El Niño decaying spring. We highlight the importance of developing high resolution climate model as it could potentially improve the climatology and interannual variability of SPR.

Influence of spring phenology on seasonal and annual carbon balance in two contrasting New England forests.

PubMed

Richardson, Andrew D; Hollinger, David Y; Dail, D Bryan; Lee, John T; Munger, J William; O'keefe, John

2009-03-01

Spring phenology is thought to exert a major influence on the carbon (C) balance of temperate and boreal ecosystems. We investigated this hypothesis using four spring onset phenological indicators in conjunction with surface-atmosphere CO(2) exchange data from the conifer-dominated Howland Forest and deciduous-dominated Harvard Forest AmeriFlux sites. All phenological measures, including CO(2) source-sink transition dates, could be well predicted on the basis of a simple two-parameter spring warming model, indicating good potential for improving the representation of phenological transitions and their dynamic responsiveness to climate variability in land surface models. The date at which canopy-scale photosynthetic capacity reached a threshold value of 12 micromol m(-2) s(-1) was better correlated with spring and annual flux integrals than were either deciduous or coniferous bud burst dates. For all phenological indicators, earlier spring onset consistently, but not always significantly, resulted in higher gross primary productivity (GPP) and ecosystem respiration (RE) for both seasonal (spring months, April-June) and annual flux integrals. The increase in RE was less than that in GPP; depending on the phenological indicator used, a one-day advance in spring onset increased springtime net ecosystem productivity (NEP) by 2-4 g C m(-2) day(-1). In general, we could not detect significant differences between the two forest types in response to earlier spring, although the response to earlier spring was generally more pronounced for Harvard Forest than for Howland Forest, suggesting that future climate warming may favor deciduous species over coniferous species, at least in this region. The effect of earlier spring tended to be about twice as large when annual rather than springtime flux integrals were considered. This result is suggestive of both immediate and lagged effects of earlier spring onset on ecosystem C cycling, perhaps as a result of accelerated N cycling rates and cascading effects on N uptake, foliar N concentrations and photosynthetic capacity.

Geomorphic Function and Restoration Potential of Spring Creeks in Southeastern Idaho: Analysis and Communication

NASA Astrophysics Data System (ADS)

Hanrahan, T. P.; Hill, Z.; Levell, A.; Maguire, T.; Risso, D.

2014-12-01

A large wetland and floodplain complex adjacent to the Snake River in southeastern Idaho, USA, encompasses numerous spring-fed creeks that originate on the floodplain and discharge at their confluence with the Snake River and American Falls Reservoir. Resource managers are implementing a program to restore these spring creeks for the recovery of Yellowstone cutthroat trout and ecosystem health. Our objectives were to evaluate the physical characteristics of these spring creeks, develop a conceptual model of their geomorphic function, compare the restoration potential of individual reaches, and communicate our findings to a broad audience of resource managers and regional stakeholders in order to foster restoration planning. A geomorphic assessment along 38 km of three spring creeks was completed by collecting data at several transects within distinct geomorphic reaches, and by collecting data continuously throughout all reaches. These data were summarized in a GIS database and used to quantify the overall geomorphic functioning of each reach. The geomorphic functional scores were scaled from 0% (non-functional) to 100% (fully functional). Among all three spring creeks, geomorphic function ranged from 29% to 63%, with bank conditions and riparian vegetation being the primary causes of overall channel degradation. Results from the geomorphic assessment fostered the development of a conceptual model for spring creek function, whereby degraded bank conditions represent the primary controlling factor of decreased geomorphic function and fish habitat quality. The reach-based geomorphic functional scoring provides an indicator of relative restoration potential for each reach, and is one of the factors used in determining site-specific priorities for protecting, enhancing, and restoring spring creeks on the Fort Hall Bottoms. The study results, conceptual model and restoration strategy were communicated to resource managers and regional stakeholders through a graphically-rich, large format atlas document. Presentation of hard copy and electronic versions of maps and infographics fostered a high level of engagement among those interested in restoring these spring creek systems.

An Unusual Cause of Dysphagia: Live Leech in the Tongue Base

PubMed Central

Erdoğan, Osman; İsmi, Onur; Vayısoğlu, Yusuf; Azizoğlu, Mustafa; Görür, Kemal; Özcan, Cengiz

2015-01-01

Inhaled or ingested foreign bodies are relatively common causes of airway obstructions. They can be associated with significant morbidity and even mortality. Although various foreign bodies are aspirated or ingested, live leeches are rarely encountered. We reported a case of a live leech at the base of the tongue in an 18-year-old female patient with a history of unfiltered spring water drinking. We discussed the surgical technique and importance of anesthesia with this brief study. PMID:29392006

An evaluation of regression methods to estimate nutritional condition of canvasbacks and other water birds

USGS Publications Warehouse

Sparling, D.W.; Barzen, J.A.; Lovvorn, J.R.; Serie, J.R.

1992-01-01

Regression equations that use mensural data to estimate body condition have been developed for several water birds. These equations often have been based on data that represent different sexes, age classes, or seasons, without being adequately tested for intergroup differences. We used proximate carcass analysis of 538 adult and juvenile canvasbacks (Aythya valisineria ) collected during fall migration, winter, and spring migrations in 1975-76 and 1982-85 to test regression methods for estimating body condition.

German Explosive Ordnance (Projectiles and Projectile Fuzes)

DTIC Science & Technology

1953-03-01

CAP IGNITER BRIDGE INSULATION BLACK POWDER Figure 320—Electric Primers c/12nA and c/22 354 PROJECTILES 0.75 inch, length of body. 0.281 inch...of lip. 0.75 inch, length of body. Number of threads, 5 RH. CONSTRUCTION. The primer houses an igniter bridge which consists of lead styphnate...dipped in gelatin. This bridge has a resistance of approxi- mately 2.2 ohms and is in the circuit with the in- sulated contact plug, the spring washer

Quantifying model-structure- and parameter-driven uncertainties in spring wheat phenology prediction with Bayesian analysis

DOE PAGES

Alderman, Phillip D.; Stanfill, Bryan

2016-10-06

Recent international efforts have brought renewed emphasis on the comparison of different agricultural systems models. Thus far, analysis of model-ensemble simulated results has not clearly differentiated between ensemble prediction uncertainties due to model structural differences per se and those due to parameter value uncertainties. Additionally, despite increasing use of Bayesian parameter estimation approaches with field-scale crop models, inadequate attention has been given to the full posterior distributions for estimated parameters. The objectives of this study were to quantify the impact of parameter value uncertainty on prediction uncertainty for modeling spring wheat phenology using Bayesian analysis and to assess the relativemore » contributions of model-structure-driven and parameter-value-driven uncertainty to overall prediction uncertainty. This study used a random walk Metropolis algorithm to estimate parameters for 30 spring wheat genotypes using nine phenology models based on multi-location trial data for days to heading and days to maturity. Across all cases, parameter-driven uncertainty accounted for between 19 and 52% of predictive uncertainty, while model-structure-driven uncertainty accounted for between 12 and 64%. Here, this study demonstrated the importance of quantifying both model-structure- and parameter-value-driven uncertainty when assessing overall prediction uncertainty in modeling spring wheat phenology. More generally, Bayesian parameter estimation provided a useful framework for quantifying and analyzing sources of prediction uncertainty.« less

Spring break trips as a risk factor for heavy alcohol use among first-year college students.

PubMed

Lee, Christine M; Maggs, Jennifer L; Rankin, Lela A

2006-11-01

Many high school and college students are believed to use spring break vacation to travel to destinations with the intent of engaging in extreme party behaviors, including excessive alcohol use. However, the extent to which spring break travelers' behaviors are more risky than their typical behaviors remains unclear. To assess the impact of spring break as a situational risk factor, we analyzed data collected from 176 first-year college students across 10 weeks using weekly telephone interviews. Using multilevel modeling, we found the following: (1) men, participants in fraternity/sorority organizations, students traveling on spring break trips, and those with higher fun-social alcohol expectancies drank more during the regular semester; (2) alcohol use did not increase during spring break week in general; however, (3) spring break travelers increased their alcohol use during spring break. Spring break trips are a risk factor for escalated alcohol use both during the academic semester and during spring break trips, suggesting that some students may seek out opportunities for excessive alcohol use. Results are discussed in terms of niche selection and prevention implications.

Exposure to suboptimal temperatures during metamorphosis reveals a critical developmental window in the solitary bee, Megachile rotundata

USDA-ARS?s Scientific Manuscript database

Metamorphosis is an important developmental stage for holometabolous insects, during which adult morphology and physiology are established. Proper development relies on optimal body temperatures, and natural ambient temperature (Ta) fluctuations, especially in spring or in northern latitudes, could ...

Student Climate Survey, Spring 1998.

ERIC Educational Resources Information Center

Truckee Meadows Community Coll., Sparks, NV.

Every three years, Truckee Meadows Community College (Nevada) administers a student climate survey that measures the attitudes, perceptions, and opinions of its student population. The instrument used to survey the student body was designed with three basic objectives in mind: (1) validate the institutional mission; (2) obtain input regarding the…

Physics in a Bouncing Car.

ERIC Educational Resources Information Center

Bartlett, Albert A.

1984-01-01

Defines frame of reference for the analysis of motion in a moving car, discussing the interaction of the car body, the seat springs, and the passenger when the car goes over a bump. Provides a related, but more advanced, problem with the motion of cars involving angular acceleration. (JM)

Dissolved oxygen fluctuations in karst spring flow and implications for endemic species: Barton Springs, Edwards aquifer, Texas, USA

USGS Publications Warehouse

Mahler, Barbara J.; Bourgeais, Renan

2013-01-01

Karst aquifers and springs provide the dissolved oxygen critical for survival of endemic stygophiles worldwide, but little is known about fluctuations of dissolved oxygen concentrations (DO) and factors that control those concentrations. We investigated temporal variation in DO at Barton Springs, Austin, Texas, USA. During 2006–2012, DO fluctuated by as much as a factor of 2, and at some periods decreased to concentrations that adversely affect the Barton Springs salamander (Eurycea sorosum) (≤4.4 mg/L), a federally listed endangered species endemic to Barton Springs. DO was lowest (≤4.4 mg/L) when discharge was low (≤1 m3/s) and spring water temperature was >21 °C, although not at a maximum; the minimum DO recorded was 4.0 mg/L. Relatively low DO (3/s) and maximum T (22.2 °C). A four-segment linear regression model with daily data for discharge and spring water temperature as explanatory variables provided an excellent fit for mean daily DO (Nash–Sutcliffe coefficient for the validation period of 0.90). DO also fluctuated at short-term timescales in response to storms, and DO measured at 15-min intervals could be simulated with a combination of discharge, spring temperature, and specific conductance as explanatory variables. On the basis of the daily-data regression model, we hypothesize that more frequent low DO corresponding to salamander mortality could result from (i) lower discharge from Barton Springs resulting from increased groundwater withdrawals or decreased recharge as a result of climate change, and (or) (ii) higher groundwater temperature as a result of climate change.

Weakening temperature control on the interannual variations of spring carbon uptake across northern lands

NASA Astrophysics Data System (ADS)

Piao, S.; Peng, S.; Liu, Z.; Ciais, P.; Wang, T.; Huang, M.; Ahlstrom, A.; Burkhart, J. F.; Chevallier, F.; Jeong, S. J.; Janssens, I. A.; Lin, X.; Mao, J.; Myneni, R.; Shi, X.; van der Velde, I. R.; Stohl, A.; Mohammat, A.; Yao, Y.; Peñuelas, J.; Zhu, Z.; Tans, P. P.

2017-12-01

Ongoing spring warming allows the growing season to begin earlier, enhancing carbon uptake in northern ecosystems. Here we use 34 years of atmospheric CO2 concentration measurements at Barrow, Alaska (BRW, 71o N) to show that the interannual relationship between spring temperature and carbon uptake has recently shifted. We use two indicators: the spring zero-crossing date of atmospheric CO2 (SZC) and the magnitude of CO2 draw down between May and June (SCC). The previously reported strong correlation between SZC, SCC and spring land temperature (ST) was found in the first 17 years of measurements, but disappeared in the last 17 years. As a result, the sensitivity of both SZC and SCC to warming decreased. Simulations with an atmospheric transport model coupled to a terrestrial ecosystem model suggest that the weakened interannual correlation of SZC and SCC with ST in the last 17 years is attributable to the declining temperature response of spring net primary productivity (NPP) rather than to changes in heterotrophic respiration or in atmospheric transport patterns. Reduced chilling during dormancy and emerging light limitation are possible mechanisms that may have contributed to the loss of NPP response to ST. Our results thus challenge the `warmer spring-bigger sink' mechanism.

Energy analysis of a DEAP based cylindrical actuator coupled with a radial negative stiffness spring

NASA Astrophysics Data System (ADS)

Chavanne, Jonathan; Civet, Yoan; Perriard, Yves

2017-04-01

The main problem to obtain considerable deformation with dielectric electro-active polymer based technology is the electrical breakdown. A simple solution consists in pre-stretching the elastomer before activating it which cancels the snap-through effect and thus avoid reaching the electrical limit. Due to the stress characteristic of the DEAP, it could be demonstrated that a spring with a negative stiffness provides the best strain. In this paper, a new design of a monostable spring with a negative stiffness is suggested for a DEAP tubular shape actuator. The particularity of the proposed solution is the radial direction of the displacement with a special load characteristic. In order to determine the performance of the system, the mechanical and electrical behaviour are investigated through analytical models with the assumption that the axial stretch stays constant. A finite element method is used to validate these latter and maximal error lower than 2% is reported. The energy chain conversion is developed in detail which allows studying all the energies transferred from both the electrical input and any pre-stretch solution to the membrane during a cycle of activation. From these models, the negative stiffness spring is compared to the common solution, i.e a constant pressure or a linear positive spring, to pre-stretch a cylindrical EAP. The results show that the linear spring always removes the snap-through behaviour contrary to the constant pressure. Depending on the geometry, the monostable solution cancels also this latter and owns a better energy transfer from the power supply to the elastomer (around 50% against 40% for the linear spring) or a better stroke compared to the linear spring. Furthermore, due to the hollow in its stress characteristic, the cylindrical shaped actuator associated to a linear spring or the proposed spring allows increasing the strain. Through the different analytical models, the definition of the electrical breakdown and the analysis of the limits of the stresses, a qualitative study of the performance is given for the different pre-stretches.

Mesozooplankton grazing during spring sea-ice conditions in the eastern Bering Sea

NASA Astrophysics Data System (ADS)

Campbell, Robert G.; Ashjian, Carin J.; Sherr, Evelyn B.; Sherr, Barry F.; Lomas, Michael W.; Ross, Celia; Alatalo, Philip; Gelfman, Celia; Keuren, Donna Van

2016-12-01

Mesozooplankton (copepods and euphausiids) grazing rates and prey preferences were determined during a series of three research cruises to the eastern Bering Sea in spring 2008, 2009, and 2010. Chlorophyll was dominated by large cells (>5 μm), especially at bloom locations where they usually comprised greater than 90% of the total chlorophyll biomass. The relative importance of microzooplankton to the prey field biomass decreased with increasing chlorophyll concentration, and was less than 10% of the total prey biomass in ice-edge bloom regions. Overall, microzooplankton was the preferred prey of the mesozooplankton, although phytoplankton/ice algae were the dominant component of the diet because of their much greater biomass, especially during blooms. There were differences between mesozooplankton species in their prey preferences: Metridia pacifica, Pseudocalanus spp. and Calanus spp. had the strongest preference for microzooplankton prey, while euphausiids (Thysanoessa spp.) and Neocalanus flemingeri/plumchrus appeared to feed non-selectively on all prey items. Mesozooplankton exhibited a saturating feeding response to chlorophyll concentration (Holling's type II) that could be modeled by Michaelis-Menten equations. Taxa-specific maximum ingestion rates generally followed allometric theory, with smaller zooplankton having higher feeding rates than larger zooplankton, and ranged from about 4-30% body carbon day-1. Trophic cascades during grazing experiments could result in a substantial underestimate of chlorophyll ingestion rates, especially for those taxa that had a strong preference for microzooplankton. Grazing impacts by mesozooplankton on the integrated chlorophyll biomass and primary production were 2.7±4.4 and 26±48% day-1, respectively. Impacts increased significantly with increasing mesozooplankton biomass, which increased from early to late spring. However, grazing impacts were extremely low in ice-edge bloom regions. Our findings suggest that even when grazing by microzooplankton is included in our grazing impact estimates, about 50% of the primary production in phytoplankton blooms during spring on the eastern Bering Sea shelf is not grazed and is available for direct export to the benthic community.

Feedback equilibrium control during human standing

PubMed Central

Alexandrov, Alexei V.; AA, Frolov; FB, Horak; P, Carlson-Kuhta; S, Park

2006-01-01

Equilibrium maintenance during standing in humans was investigated with a 3-joint (ankle, knee and hip) sagittal model of body movement. The experimental paradigm consisted of sudden perturbations of humans in quiet stance by backward displacements of the support platform. Data analysis was performed using eigenvectors of motion equation. The results supported three conclusions. First, independent feedback control of movements along eigenvectors (eigenmovements) can adequately describe human postural responses to stance perturbations. This conclusion is consistent with previous observations (Alexandrov et al., 2001b) that these same eigenmovements are also independently controlled in a feed-forward manner during voluntary upper-trunk bending. Second, independent feedback control of each eigenmovement is sufficient to provide its stability. Third, the feedback loop in each eigenmovement can be modeled as a linear visco-elastic spring with delay. Visco-elastic parameters and time-delay values result from the combined contribution of passive visco-elastic mechanisms and sensory systems of different modalities. PMID:16228222

High-speed trains subject to abrupt braking

NASA Astrophysics Data System (ADS)

Tran, Minh Thi; Ang, Kok Keng; Luong, Van Hai; Dai, Jian

2016-12-01

The dynamic response of high-speed train subject to braking is investigated using the moving element method. Possible sliding of wheels over the rails is accounted for. The train is modelled as a 15-DOF system comprising of a car body, two bogies and four wheels interconnected by spring-damping units. The rail is modelled as a Euler-Bernoulli beam resting on a two-parameter elastic damped foundation. The interaction between the moving train and track-foundation is accounted for through the normal and tangential wheel-rail contact forces. The effects of braking torque, wheel-rail contact condition, initial train speed and severity of railhead roughness on the dynamic response of the high-speed train are investigated. For a given initial train speed and track irregularity, the study revealed that there is an optimal braking torque that would result in the smallest braking distance with no occurrence of wheel sliding, representing a good compromise between train instability and safety.

Fixtureless nonrigid part inspection using depth cameras

NASA Astrophysics Data System (ADS)

Xiong, Hanwei; Xu, Jun; Xu, Chenxi; Pan, Ming

2016-10-01

In automobile industry, flexible thin shell parts are used to cover car body. Such parts could have a different shape in a free state than the design model due to dimensional variation, gravity loads and residual strains. Special inspection fixtures are generally indispensable for geometric inspection. Recently, some researchers have proposed fixtureless nonridged inspect methods using intrinsic geometry or virtual spring-mass system, based on some assumptions about deformation between Free State shape and nominal CAD shape. In this paper, we propose a new fixtureless method to inspect flexible parts with a depth camera, which is efficient and low computational complexity. Unlike traditional method, we gather two point cloud set of the manufactured part in two different states, and make correspondences between them and one of them to the CAD model. The manufacturing defects can be derived from the correspondences. Finite element method (FEM) disappears in our method. Experimental evaluation of the proposed method is presented.

Spatial distribution and risk assessment of Johnsongrass (sorghum halepense) in Big Bend National Park, Texas

USDA-ARS?s Scientific Manuscript database

We used Landsat 7 ETM+ imagery to illustrate how remotely sensed data can model predicted Johnsongrass habitat. We used spectral reflectance values for three seasons of data across 5 years (fall 1999, summer and fall 2000, spring and fall 2001, spring 2002, and spring 2003) to capture Johnsongrass v...

How Reflected Wave Fronts Dynamically Establish Hooke's Law in a Spring

ERIC Educational Resources Information Center

Fahy, Stephen; O'Riordan, John; O'Sullivan, Colm; Twomey, Patrick

2012-01-01

A simple benchtop experiment in which a moving cart collides with a fixed spring is described. Force-time and force-distance data recorded during the collision display the transit of compression wave fronts through the spring following impact. These data can be used by students to develop a computational model of the dynamics of this simple…

Source contributions to Northern Hemisphere CO and black carbon during spring and summer 2008 from POLARCAT and START08/preHIPPO observations and MOZART-4

NASA Astrophysics Data System (ADS)

Tilmes, S.; Emmons, L. K.; Law, K. S.; Ancellet, G.; Schlager, H.; Paris, J.-D.; Fuelberg, H. E.; Streets, D. G.; Wiedinmyer, C.; Diskin, G. S.; Kondo, Y.; Holloway, J.; Schwarz, J. P.; Spackman, J. R.; Campos, T.; Nédélec, P.; Panchenko, M. V.

2011-02-01

Anthropogenic pollution and wildfires are main producers of carbon monoxide (CO) and black carbon (BC) in the Northern Hemisphere. High concentrations of these compounds are transported into the Arctic troposphere, influencing the ecosystem in high northern latitudes and the global climate. The global chemical transport model MOZART-4 is used to quantify the seasonal evolution of the contribution of CO and BC from different source regions in spring and summer 2008 by tagging their emissions. Aircraft observations from the POLARCAT experiments, in particular NASA ARCTAS, NOAA ARCPAC, POLARCAT-France, DLR GRACE and YAK-AEROSIB, as well as the NSF START08/preHIPPO experiments during Spring-Summer 2008 are combined to quantify the representation of simulated tracer characteristics in anthropogenic and fire plumes. In general, the model reproduces CO and BC well. Based on aircraft measurements and FLEXPART back-trajectories, the altitude contribution of emissions coming from different source regions is well captured in the model. Uncertainties of the MOZART-4 model are identified by comparing the data with model results on the flight tracks and using MOPITT satellite observations. Anthropogenic emissions are underestimated by about 10% in high northern latitudes in spring, and shortcomings exist in simulating fire plumes. The remote impact of East-Siberian fire emissions is underestimated for spring, whereas the impact of Southeast Asian fire emissions to mid-latitude CO values is overestimated by the model. In summer, mid-latitude CO values agree well between model and observations, whereas summer high latitude East-Siberian fire emissions in the model are overestimated by 20% in comparison to observations in the region. On the other hand, CO concentrations are underestimated by about 30% over Alaska and Canada at altitudes above 4 km. BC values are overestimated by the model at altitudes above 4 km in summer. Based on MOZART-4, with tagged CO and BC tracers, anthropogenic emissions of Asia, Europe and the US have the largest contribution to the CO and BC in mid- and high latitudes in spring and summer. Southeast Asian, Chinese and Indian fires have a large impact on CO pollution in spring in low latitudes with a maximum between 20° and 30°, whereas Siberian fires contribute largely to the pollution in high latitudes, up to 10% in spring and up to 30% in summer. The largest contributions to BC values in high latitudes are from anthropogenic emissions (about 70%). CO and BC have larger mass loadings in April than in July, as a result of photochemistry and dynamics.

Application of Force and Energy Approaches to the Problem of a One-Dimensional, Fully Connected, Nonlinear-Spring Lattice Structure

DTIC Science & Technology

2015-09-01

Respondents should be aware that notwithstanding any other provision of  law , no person shall be subject to any penalty  for failing to comply with a...other hand, had posited the law of energy conservation in 1853. By the end of the decade, physicists such as Helmholtz, Thomson, Rankine, and Maxwell...forces are applied to a body, which, in turn, establishes resultant internal forces in the body. If the consti- tutive laws governing the body are

Modeling Study of the Effect of Anthropogenic Aerosols on Late Spring Drought in South China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Ning; Liu, Xiaohong

2013-10-01

In this study, the mechanisms underlying the decadal variability of late spring precipitation in south China are investigated using the latest version 1 of Community Earth System Model (CESM1). We aim to unravel the effects of different climate forcing agents, such as aerosols and greenhouse gases (GHGs), on the decadal variation of precipitation with transient experiments from pre-industry (for year 1850) to present-day (for year 2000). Our results reveal that: (1) CESM1 can reproduce the climatological features of atmospheric circulation and precipitation for the late spring in south China; (2) Only simulations including the forcing of anthropogenic aerosols can reproducemore » the observed decreasing trend of late spring precipitation from 1950-2000 in south China; (3) Aerosols affect the decadal change of precipitation mainly by altering the large scale atmospheric circulation, and to a less extent by increasing the lower-tropospheric stability to inhibit the convective precipitation; and (4) In comparison, other climate forcing agents, such as GHGs, have much smaller effects on the decadal change of spring precipitation in south China. Key words: precipitation, aerosols, climate change, south China, Community Earth System Model« less

Evaluation of massless-spring modeling of suspension-line elasticity during the parachute unfurling process

NASA Technical Reports Server (NTRS)

Poole, L. R.; Huckins, E. K., III

1972-01-01

A general theory on mathematical modeling of elastic parachute suspension lines during the unfurling process was developed. Massless-spring modeling of suspension-line elasticity was evaluated in detail. For this simple model, equations which govern the motion were developed and numerically integrated. The results were compared with flight test data. In most regions, agreement was satisfactory. However, poor agreement was obtained during periods of rapid fluctuations in line tension.

Hydrogeologic setting and conceptual hydrologic model of the Spring Creek basin, Centre County, Pennsylvania

USGS Publications Warehouse

Fulton, John W.; Koerkle, Edward H.; McAuley, Steven D.; Hoffman, Scott A.; Zarr, Linda F.

2005-01-01

The Spring Creek Basin, Centre County, Pa., is experiencing some of the most rapid growth and development within the Commonwealth. This trend has resulted in land-use changes and increased water use, which will affect the quantity and quality of stormwater runoff, surface water, ground water, and aquatic resources within the basin. The U.S. Geological Survey (USGS), in cooperation with the ClearWater Conservancy (CWC), Spring Creek Watershed Community (SCWC), and Spring Creek Watershed Commission (SCWCm), has developed a Watershed Plan (Plan) to assist decision makers in water-resources planning. One element of the Plan is to provide a summary of the basin characteristics and a conceptual model that incorporates the hydrogeologic characteristics of the basin. The report presents hydrogeologic data for the basin and presents a conceptual model that can be used as the basis for simulating surface-water and ground-water flow within the basin. Basin characteristics; sources of data referenced in this text; physical characteristics such as climate, physiography, topography, and land use; hydrogeologic characteristics; and water-quality characteristics are discussed. A conceptual model is a simplified description of the physical components and interaction of the surface- and ground-water systems. The purpose for constructing a conceptual model is to simplify the problem and to organize the available data so that the system can be analyzed accurately. Simplification is necessary, because a complete accounting of a system, such as Spring Creek, is not possible. The data and the conceptual model could be used in development of a fully coupled numerical model that dynamically links surface water, ground water, and land-use changes. The model could be used by decision makers to manage water resources within the basin and as a prototype that is transferable to other watersheds.

Drop Hammer Tests with Three Oleo Strut Models and Three Different Shock Strut Oils at Low Temperatures

NASA Technical Reports Server (NTRS)

Kranz, M

1954-01-01

Drop hammer tests with different shock strut models and shock strut oils were performed at temperatures ranging to -40 C. The various shock strut models do not differ essentially regarding their springing and damping properties at low temperatures; however, the influence of the different shock strut oils on the springing properties at low temperatures varies greatly.

Breaking through to Reluctant Readers

ERIC Educational Resources Information Center

Clarke, Bill

2006-01-01

With 70 percent of its student body entering school reading below grade level, Blackstone Academy Charter School realized that teachers needed to make literacy a pillar of the school's culture. This 9-12 urban high school administers a reading evaluation developed by the Northwest Evaluation Association each fall and spring to all incoming…

10 CFR 63.302 - Definitions for Subpart L.

Code of Federal Regulations, 2010 CFR

2010-01-01

...; and (5) The lithosphere. Aquifer means a water-bearing underground geological formation, group of formations, or part of a formation (excluding perched water bodies) that can yield a significant amount of ground water to a well or spring. Controlled area means: (1) The surface area, identified by passive...

10 CFR 63.302 - Definitions for Subpart L.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; and (5) The lithosphere. Aquifer means a water-bearing underground geological formation, group of formations, or part of a formation (excluding perched water bodies) that can yield a significant amount of ground water to a well or spring. Controlled area means: (1) The surface area, identified by passive...

Diet and body shape changes of pāroko Kelloggella disalvoi (Gobiidae) from intertidal pools of Easter Island.

PubMed

Vera-Duarte, J; Bustos, C A; Landaeta, M F

2017-11-01

This study assesses seasonal variation in the morphology and diet of juveniles and adults of the Easter Island endemic goby Kelloggella disalvoi from intertidal pools during September-October 2015 (spring) and June-July 2016 (winter), utilizing geometric morphometric and gut-content analyses. A set of 16 landmarks was digitized in 128 individuals. Shape changes related to size changes (i.e. allometry) were low (18·6%) and were seasonally similar. Body shape changes were mainly dorsoventral (44·2% of variance) and comprised posteroventral displacement of the premaxilla and bending of the body. The latter included vertical displacement of the anterior portion of the first and second dorsal fins and the entire base of the caudal fin. Diets mainly comprised developmental stages of harpacticoid copepods (from eggs to adults), ostracods, isopods, gastropods and bivalves. Also, trophic niche breadth remained constant throughout development and did not vary between seasons. Nonetheless, significant dietary differences were detected in specimens collected during spring (main prey items: harpacticoid copepods and copepod eggs) and winter (harpacticoid copepods and copepod nauplii). Finally, there was weak but significant covariation between diet and morphology: molluscivores were characterized by having an inferior mouth gape, whereas planktivores had an anteriorly directed premaxilla. © 2017 The Fisheries Society of the British Isles.

Importance of climatological downscaling and plant phenology for red deer in heterogeneous landscapes

PubMed Central

Pettorelli, Nathalie; Mysterud, Atle; Yoccoz, Nigel G; Langvatn, Rolf; Stenseth, Nils Chr

2005-01-01

Understanding how climate influences ecosystems represents a challenge in ecology and natural resource management. Although we know that climate affects plant phenology and herbivore performances at any single site, no study has directly coupled the topography–climate interaction (i.e. the climatological downscaling process) with large-scale vegetation dynamics and animal performances. Here we show how climatic variability (measured by the North Atlantic oscillation ‘NAO’) interacts with local topography in determining the vegetative greenness (as measured by the normalized difference vegetation index ‘NDVI’) and the body masses and seasonal movements of red deer (Cervus elaphus) in Norway. Warm springs induced an earlier onset of vegetation, resulting in earlier migration and higher body masses. Increasing values of the winter-NAO corresponded to less snow at low altitude (warmer, more precipitation results in more rain), but more snow at high altitude (colder, more precipitation corresponds to more snow) relative to winters with low winter-NAO. An increasing NAO thus results in a spatially more variable phenology, offering migrating deer an extended period with access to high-quality forage leading to increased body mass. Our results emphasize the importance of incorporating spring as well as the interaction between winter climate and topography when aiming at understanding how plant and animal respond to climate change. PMID:16243701

Development of new vibration energy flow analysis software and its applications to vehicle systems

NASA Astrophysics Data System (ADS)

Kim, D.-J.; Hong, S.-Y.; Park, Y.-H.

2005-09-01

The Energy flow analysis (EFA) offers very promising results in predicting the noise and vibration responses of system structures in medium-to-high frequency ranges. We have developed the Energy flow finite element method (EFFEM) based software, EFADSC++ R4, for the vibration analysis. The software can analyze the system structures composed of beam, plate, spring-damper, rigid body elements and many other components developed, and has many useful functions in analysis. For convenient use of the software, the main functions of the whole software are modularized into translator, model-converter, and solver. The translator module makes it possible to use finite element (FE) model for the vibration analysis. The model-converter module changes FE model into energy flow finite element (EFFE) model, and generates joint elements to cover the vibrational attenuation in the complex structures composed of various elements and can solve the joint element equations by using the wave tra! nsmission approach very quickly. The solver module supports the various direct and iterative solvers for multi-DOF structures. The predictions of vibration for real vehicles by using the developed software were performed successfully.

Performances estimation of a rotary traveling wave ultrasonic motor based on two-dimension analytical model.

PubMed

Ming, Y; Peiwen, Q

2001-03-01

The understanding of ultrasonic motor performances as a function of input parameters, such as the voltage amplitude, driving frequency, the preload on the rotor, is a key to many applications and control of ultrasonic motor. This paper presents performances estimation of the piezoelectric rotary traveling wave ultrasonic motor as a function of input voltage amplitude and driving frequency and preload. The Love equation is used to derive the traveling wave amplitude on the stator surface. With the contact model of the distributed spring-rigid body between the stator and rotor, a two-dimension analytical model of the rotary traveling wave ultrasonic motor is constructed. Then the performances of stead rotation speed and stall torque are deduced. With MATLAB computational language and iteration algorithm, we estimate the performances of rotation speed and stall torque versus input parameters respectively. The same experiments are completed with the optoelectronic tachometer and stand weight. Both estimation and experiment results reveal the pattern of performance variation as a function of its input parameters.

A 3D virtual reality simulator for training of minimally invasive surgery.

PubMed

Mi, Shao-Hua; Hou, Zeng-Gunag; Yang, Fan; Xie, Xiao-Liang; Bian, Gui-Bin

2014-01-01

For the last decade, remarkable progress has been made in the field of cardiovascular disease treatment. However, these complex medical procedures require a combination of rich experience and technical skills. In this paper, a 3D virtual reality simulator for core skills training in minimally invasive surgery is presented. The system can generate realistic 3D vascular models segmented from patient datasets, including a beating heart, and provide a real-time computation of force and force feedback module for surgical simulation. Instruments, such as a catheter or guide wire, are represented by a multi-body mass-spring model. In addition, a realistic user interface with multiple windows and real-time 3D views are developed. Moreover, the simulator is also provided with a human-machine interaction module that gives doctors the sense of touch during the surgery training, enables them to control the motion of a virtual catheter/guide wire inside a complex vascular model. Experimental results show that the simulator is suitable for minimally invasive surgery training.

Static Design and Finite Element Analysis of Innovative CFRP Transverse Leaf Spring

NASA Astrophysics Data System (ADS)

Carello, M.; Airale, A. G.; Ferraris, A.; Messana, A.; Sisca, L.

2017-12-01

This paper describes the design and the numerical modelization of a novel transverse Carbon Fiber Reinforced Plastic (CFRP) leaf-spring prototype for a multilink suspension. The most significant innovation is in the functional integration where the leaf spring has been designed to work as spring, anti-roll bar, lower and longitudinal arms at the same time. In particular, the adopted work flow maintains a very close correlation between virtual simulations and experimental tests. Firstly, several tests have been conducted on the CFRP specimen to characterize the material property. Secondly, a virtual card fitting has been carried out in order to set up the leaf-spring Finite Element (FE) model using CRASURV formulation as material law and RADIOSS as solver. Finally, extensive tests have been done on the manufactured component for validation. The results obtained show a good agreement between virtual simulation and experimental tests. Moreover, this solution enabled the suspension to reduce about 75% of the total mass without losing performance.

Geometrically induced nonlinear dynamics in one-dimensional lattices

NASA Astrophysics Data System (ADS)

Hamilton, Merle D.; de Alcantara Bonfim, O. F.

2006-03-01

We present a lattice model consisting of a single one-dimensional chain, where the masses are interconnected by linear springs and allowed to move in a horizontal direction only, as in a monorail. In the transverse direction each mass is also attached to two other linear springs, one on each side of the mass. The ends of these springs are kept at fixed positions. The nonlinearity in the model arises from the geometric constraints imposed on the motion of the masses, as well as from the configuration of the springs, where in the transverse direction the springs are either in the extended or compressed state depending on the position of the masses. Under these conditions we show that solitary waves are present in the system. In the long wavelength limit an analytic solution for these nonlinear waves is found. Numerical integrations of the equations of motion in the full system are also performed to analyze the conditions for the existence and stability of the nonlinear waves.

Elastohydrodynamic synchronization of adjacent beating flagella

NASA Astrophysics Data System (ADS)

Goldstein, Raymond E.; Lauga, Eric; Pesci, Adriana I.; Proctor, Michael R. E.

2016-11-01

It is now well established that nearby beating pairs of eukaryotic flagella or cilia typically synchronize in phase. A substantial body of evidence supports the hypothesis that hydrodynamic coupling between the active filaments, combined with waveform compliance, provides a robust mechanism for synchrony. This elastohydrodynamic mechanism has been incorporated into bead-spring models in which the beating flagella are represented by microspheres tethered by radial springs as they are driven about orbits by internal forces. While these low-dimensional models reproduce the phenomenon of synchrony, their parameters are not readily relatable to those of the filaments they represent. More realistic models, which reflect the underlying elasticity of the axonemes and the active force generation, take the form of fourth-order nonlinear partial differential equations (PDEs). While computational studies have shown the occurrence of synchrony, the effects of hydrodynamic coupling between nearby filaments governed by such continuum models have been examined theoretically only in the regime of interflagellar distances d large compared to flagellar length L . Yet in many biological situations d /L ≪1 . Here we present an asymptotic analysis of the hydrodynamic coupling between two extended filaments in the regime d /L ≪1 and find that the form of the coupling is independent of the microscopic details of the internal forces that govern the motion of the individual filaments. The analysis is analogous to that yielding the localized induction approximation for vortex filament motion, extended to the case of mutual induction. In order to understand how the elastohydrodynamic coupling mechanism leads to synchrony of extended objects, we introduce a heuristic model of flagellar beating. The model takes the form of a single fourth-order nonlinear PDE whose form is derived from symmetry considerations, the physics of elasticity, and the overdamped nature of the dynamics. Analytical and numerical studies of this model illustrate how synchrony between a pair of filaments is achieved through the asymptotic coupling.

Evaluation of High Temperature Knitted Spring Tubes for Structural Seal Applications

NASA Technical Reports Server (NTRS)

Taylor, Shawn C.; DeMange, Jeffrey J.; Dunlap, Patrick H., Jr.; Steinetz, Bruce M.

2004-01-01

Control surface seals are crucial to current and future space vehicles, as they are used to seal the gaps surrounding body flaps, elevons, and other actuated exterior surfaces. During reentry, leakage of high temperature gases through these gaps could damage underlying lower temperature structures such as rudder drive motors and mechanical actuators, resulting in impaired vehicle control. To be effective, control surface seals must shield lower temperature structures from heat transfer by maintaining sufficient resiliency to remain in contact with opposing sealing surfaces through multiple compression cycles. The current seal exhibits significant loss of resiliency after a few compression cycles at elevated temperatures (i.e., 1900 F) and therefore would be inadequate for advanced space vehicles. This seal utilizes a knitted Inconel X-750 spring tube as its primary resilient element. As part of a larger effort to enhance seal resiliency, researchers at the NASA Glenn Research Center performed high temperature compression testing (up to 2000 F) on candidate spring tube designs employing material substitutions and modified geometries. These tests demonstrated significant improvements in spring tube resiliency (5.5x better at 1750 F) through direct substitution of heat treated Rene 41 alloy in the baseline knit design. The impact of geometry modification was minor within the range of parameters tested, however trends did suggest that moderate resiliency improvements could be obtained by optimizing the current spring tube geometry.

Analysis of methods to estimate spring flows in a karst aquifer

USGS Publications Warehouse

Sepulveda, N.

2009-01-01

Hydraulically and statistically based methods were analyzed to identify the most reliable method to predict spring flows in a karst aquifer. Measured water levels at nearby observation wells, measured spring pool altitudes, and the distance between observation wells and the spring pool were the parameters used to match measured spring flows. Measured spring flows at six Upper Floridan aquifer springs in central Florida were used to assess the reliability of these methods to predict spring flows. Hydraulically based methods involved the application of the Theis, Hantush-Jacob, and Darcy-Weisbach equations, whereas the statistically based methods were the multiple linear regressions and the technology of artificial neural networks (ANNs). Root mean square errors between measured and predicted spring flows using the Darcy-Weisbach method ranged between 5% and 15% of the measured flows, lower than the 7% to 27% range for the Theis or Hantush-Jacob methods. Flows at all springs were estimated to be turbulent based on the Reynolds number derived from the Darcy-Weisbach equation for conduit flow. The multiple linear regression and the Darcy-Weisbach methods had similar spring flow prediction capabilities. The ANNs provided the lowest residuals between measured and predicted spring flows, ranging from 1.6% to 5.3% of the measured flows. The model prediction efficiency criteria also indicated that the ANNs were the most accurate method predicting spring flows in a karst aquifer. ?? 2008 National Ground Water Association.

Analysis of methods to estimate spring flows in a karst aquifer.

PubMed

Sepúlveda, Nicasio

2009-01-01

Hydraulically and statistically based methods were analyzed to identify the most reliable method to predict spring flows in a karst aquifer. Measured water levels at nearby observation wells, measured spring pool altitudes, and the distance between observation wells and the spring pool were the parameters used to match measured spring flows. Measured spring flows at six Upper Floridan aquifer springs in central Florida were used to assess the reliability of these methods to predict spring flows. Hydraulically based methods involved the application of the Theis, Hantush-Jacob, and Darcy-Weisbach equations, whereas the statistically based methods were the multiple linear regressions and the technology of artificial neural networks (ANNs). Root mean square errors between measured and predicted spring flows using the Darcy-Weisbach method ranged between 5% and 15% of the measured flows, lower than the 7% to 27% range for the Theis or Hantush-Jacob methods. Flows at all springs were estimated to be turbulent based on the Reynolds number derived from the Darcy-Weisbach equation for conduit flow. The multiple linear regression and the Darcy-Weisbach methods had similar spring flow prediction capabilities. The ANNs provided the lowest residuals between measured and predicted spring flows, ranging from 1.6% to 5.3% of the measured flows. The model prediction efficiency criteria also indicated that the ANNs were the most accurate method predicting spring flows in a karst aquifer.

Project Tradition and Technology (Project TNT): The Hualapai Bilingual Academic Excellence Program.

ERIC Educational Resources Information Center

Reed, Michael D.; And Others

Project Tradition and Technology (TNT) at Peach Springs Elementary School (Peach Springs, Arizona) is 1 of 12 programs recognized nationally as an outstanding model of bilingual education by the U.S. Department of Education. Project TNT is a process-oriented curriculum development model that identifies the community's needs and expectations for…

Investigation of the mineral potential of the Clipper Gap, Lone Mountain-Weepah, and Pipe Spring plutons, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tingley, J.V.; Maldonado, F.

1983-09-15

The Clipper Gap pluton, composed mostly of quartz monzonite with minor granite, granodiorite, and crosscutting alaskite dikes, intrudes Paleozoic western facies strata. A narrow zone of contact metamorphism is present at the intrusive-sediment contact. No mineral production has been recorded from Clipper Gap, but quartz veins containing gold-silver-copper mineral occurrences have been prospected there from the late 1800's to the present. Areas of the Lone Mountain-Weepah plutons that were studied are located in Esmeralda County about 14 km west of Tonopah, Nevada. At Lone Mountain, a Cretaceous intrusive cuts folded Precambrian and Cambrian sediments. Lead-zinc ores have been mined frommore » small replacement ore bodies in the Alpine district, west of Lone Mountain. Copper and molybdenum occurrences have been found along the east flank of Lone Mountain, and altered areas were noted in intrusive outcrops around the south end of Lone Mountain. Mineral occurrences are widespread and varied with mining activity dating back to the 1860's. The Pipe Spring pluton study area is flanked by two important mining districts, Manhattan to the north and Belmont to the northeast. Mining activity at Belmont dates from 1865. Activity at Manhattan was mainly between 1907 and 1947, but the district is active at the present time (1979). Four smaller mining areas, Monarch, Spanish Springs, Baxter Spring, and Willow Springs, are within the general boundary of the area. The Pipe Spring pluton study area contains numerous prospects along the northern contact zone of the pluton. Tungsten-bearing veins occur within the pluton near Spanish Springs, with potential for gold-tungsten placer in the Ralston Valley. Nickel and associated metals occur at Willow Spring and Monarch Ranch, where prospects may be associated with the margin of the Big Ten Peak Caldera.« less

Dynamic elastic-plastic response of a 2-DOF mass-spring system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, Edmundo

The objective of the work presented here arose from abnormal, drop scenarios and specifically the question of how the accelerations and accumulation of plastic strains of internal components could be a ected by the material properties of the external structure. In some scenarios, the impact loads can induce cyclic motion of the internal components. Therefore, a second objective was to explore di erences that could be expected when simulations are conducted using isotropic hardening vs. kinematic hardening plasticity models. The simplest model that can be used to investigate the objectives above is a two-degree-offreedom mass/spring model where the springs exhibitmore » elastic-plastic behavior. The purpose of this memo is to develop such model and present a few results that address the objectives.« less

Monitoring and analysis of liquid storage in LNG tank based on different support springs

NASA Astrophysics Data System (ADS)

He, Hua; Sun, Jianping; Li, Ke; Wu, Zheng; Chen, Qidong; Chen, Guodong; Cao, Can

2018-04-01

With the rapid development of social modernization, LNG vehicles are springing up in daily life. However, it is difficult to monitor and judge the liquid storage tanks accurately and quickly. Based on this, this paper presents a new method of liquid storage monitoring, LNG tank on-line vibration monitoring system. By collecting the vibration frequency of LNG tank and tank liquid and supporting spring system, the liquid storage quality in the tank can be calculated. In this experiment, various vibration modes of the tank spring system are fully taken into account. The vibration effects of different types of support springs on the LNG tank system were investigated. The results show that the spring model has a great influence on the test results. This study provides a technical reference for the selection of suitable support springs for liquid storage monitoring.

Updated numerical model with uncertainty assessment of 1950-56 drought conditions on brackish-water movement within the Edwards aquifer, San Antonio, Texas

USGS Publications Warehouse

Brakefield, Linzy K.; White, Jeremy T.; Houston, Natalie A.; Thomas, Jonathan V.

2015-01-01

Predictive results of total spring discharge during the 7-year period, as well as head predictions at Bexar County index well J-17, were much different than the dissolved-solids concentration change results at the production wells. These upper bounds are an order of magnitude larger than the actual prediction which implies that (1) the predictions of total spring discharge at Comal and San Marcos Springs and head at Bexar County index well J-17 made with this model are not reliable, and (2) parameters that control these predictions are not informed well by the observation dataset during historymatching, even though the history-matching process yielded parameters to reproduce spring discharges and heads at these locations during the history-matching period. Furthermore, because spring discharges at these two springs and heads at Bexar County index well J-17 represent more of a cumulative effect of upstream conditions over a larger distance (and longer time), many more parameters (with their own uncertainties) are potentially controlling these predictions than the prediction of dissolved-solids concentration change at the prediction wells, and therefore contributing to a large posterior uncertainty.

Resistivity characterisation of Hakone volcano, Central Japan, by three-dimensional magnetotelluric inversion

NASA Astrophysics Data System (ADS)

Yoshimura, Ryokei; Ogawa, Yasuo; Yukutake, Yohei; Kanda, Wataru; Komori, Shogo; Hase, Hideaki; Goto, Tada-nori; Honda, Ryou; Harada, Masatake; Yamazaki, Tomoya; Kamo, Masato; Kawasaki, Shingo; Higa, Tetsuya; Suzuki, Takeshi; Yasuda, Yojiro; Tani, Masanori; Usui, Yoshiya

2018-04-01

On 29 June 2015, a small phreatic eruption occurred at Hakone volcano, Central Japan, forming several vents in the Owakudani geothermal area on the northern slope of the central cones. Intense earthquake swarm activity and geodetic signals corresponding to the 2015 eruption were also observed within the Hakone caldera. To complement these observations and to characterise the shallow resistivity structure of Hakone caldera, we carried out a three-dimensional inversion of magnetotelluric measurement data acquired at 64 sites across the region. We utilised an unstructured tetrahedral mesh for the inversion code of the edge-based finite element method to account for the steep topography of the region during the inversion process. The main features of the best-fit three-dimensional model are a bell-shaped conductor, the bottom of which shows good agreement with the upper limit of seismicity, beneath the central cones and the Owakudani geothermal area, and several buried bowl-shaped conductive zones beneath the Gora and Kojiri areas. We infer that the main bell-shaped conductor represents a hydrothermally altered zone that acts as a cap or seal to resist the upwelling of volcanic fluids. Enhanced volcanic activity may cause volcanic fluids to pass through the resistive body surrounded by the altered zone and thus promote brittle failure within the resistive body. The overlapping locations of the bowl-shaped conductors, the buried caldera structures and the presence of sodium-chloride-rich hot springs indicate that the conductors represent porous media saturated by high-salinity hot spring waters. The linear clusters of earthquake swarms beneath the Kojiri area may indicate several weak zones that formed due to these structural contrasts.[Figure not available: see fulltext.

A recursive Bayesian updating model of haptic stiffness perception.

PubMed

Wu, Bing; Klatzky, Roberta L

2018-06-01

Stiffness of many materials follows Hooke's Law, but the mechanism underlying the haptic perception of stiffness is not as simple as it seems in the physical definition. The present experiments support a model by which stiffness perception is adaptively updated during dynamic interaction. Participants actively explored virtual springs and estimated their stiffness relative to a reference. The stimuli were simulations of linear springs or nonlinear springs created by modulating a linear counterpart with low-amplitude, half-cycle (Experiment 1) or full-cycle (Experiment 2) sinusoidal force. Experiment 1 showed that subjective stiffness increased (decreased) as a linear spring was positively (negatively) modulated by a half-sinewave force. In Experiment 2, an opposite pattern was observed for full-sinewave modulations. Modeling showed that the results were best described by an adaptive process that sequentially and recursively updated an estimate of stiffness using the force and displacement information sampled over trajectory and time. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Integrating GLL-Weibull Distribution Within a Bayesian Framework for Life Prediction of Shape Memory Alloy Spring Undergoing Thermo-mechanical Fatigue

NASA Astrophysics Data System (ADS)

Kundu, Pradeep; Nath, Tameshwer; Palani, I. A.; Lad, Bhupesh K.

2018-06-01

The present paper tackles an important but unmapped problem of the reliability estimations of smart materials. First, an experimental setup is developed for accelerated life testing of the shape memory alloy (SMA) springs. Generalized log-linear Weibull (GLL-Weibull) distribution-based novel approach is then developed for SMA spring life estimation. Applied stimulus (voltage), elongation and cycles of operation are used as inputs for the life prediction model. The values of the parameter coefficients of the model provide better interpretability compared to artificial intelligence based life prediction approaches. In addition, the model also considers the effect of operating conditions, making it generic for a range of the operating conditions. Moreover, a Bayesian framework is used to continuously update the prediction with the actual degradation value of the springs, thereby reducing the uncertainty in the data and improving the prediction accuracy. In addition, the deterioration of material with number of cycles is also investigated using thermogravimetric analysis and scanning electron microscopy.

Airfoil flutter model suspension system

NASA Technical Reports Server (NTRS)

Reed, Wilmer H. (Inventor)

1987-01-01

A wind tunnel suspension system for testing flutter models under various loads and at various angles of attack is described. The invention comprises a mounting bracket assembly affixing the suspension system to the wind tunnel, a drag-link assembly and a compound spring arrangement comprises a plunge spring working in opposition to a compressive spring so as to provide a high stiffness to trim out steady state loads and simultaneously a low stiffness to dynamic loads. By this arrangement an airfoil may be tested for oscillatory response in both plunge and pitch modes while being held under high lifting loads in a wind tunnel.

Lentic small water bodies: Variability of pesticide transport and transformation patterns.

PubMed

Ulrich, Uta; Hörmann, Georg; Unger, Malte; Pfannerstill, Matthias; Steinmann, Frank; Fohrer, Nicola

2018-03-15

Lentic small water bodies have a high ecological potential as they fulfill several ecosystem services such as the retention of water and pollutants. They serve as a hot spot of biodiversity. Due to their location in or adjacent to agricultural fields, they can be influenced by inputs of pesticides and their transformation products. Since small water bodies have rarely been part of monitorings/campaigns up to now, their current exposure and processes guiding the pesticide input are not understood, yet. This study presents results of a sampling campaign of 10 lentic small water bodies from 2015 to 2016. They were sampled once after the spring application for a pesticide target screening, before autumn application and three times after rainfall events following the application. The autumn sampling focused on the herbicides metazachlor, flufenacet and their transformation products - oxalic acid and - sulfonic acid as representatives for common pesticides in the study region. The concentrations were associated with rainfall before and after application, characteristics of the site and the water bodies, physicochemical parameters and the applied amount of pesticides. The key results of the pesticide screening in spring indicate positive detections of pesticides which have not been applied for years to the single fields. The autumn sampling showed frequent occurrences of the transformation products, which are formed in soil, from 39% to 94% of all samples (n=71). Discharge patterns were observed for metazachlor with highest concentrations in the first sample after application and then decreasing, but not for flufenacet. The concentrations of the transformation products increased over time and revealed highest values mainly in the last sample. Besides rainfall patterns right after application, the spatial and temporal dissemination of the pesticides to the water bodies seems to play a major role to understand the exposure of lentic small water bodies. Copyright © 2017 Elsevier B.V. All rights reserved.

Body-size spectra of biofilm-dwelling protozoa and their seasonal shift in coastal ecosystems.

PubMed

Zhao, Lu; Xu, Guangjian; Wang, Zheng; Xu, Henglong

2016-10-01

Community-based assessment of protozoa is usually performed at a taxon-dependent resolution. As an inherent 'taxon-free' trait, however, body-size spectrum has proved to be a highly informative indicator to summarize the functional structure of a community in both community research and monitoring programs in aquatic ecosystems. To demonstrate the relationships between the taxon-free resolution of protozoan communities and water conditions, the body-size spectra of biofilm-dwelling protozoa and their seasonal shift and environmental drivers were explored based on an annual dataset collected monthly from coastal waters of the Yellow Sea, northern China. Body sizes were calculated in equivalent spherical diameter (ESD). Among a total of 8 body-size ranks, S2 (19-27μm), S3 (28-36μm), S4 (37-50μm) and S5 (53-71μm) were the top four levels in frequency of occurrence, while rank S1 (13-17μm), S2 and S4 were the dominant levels in abundance. These dominants showed a clear seasonal succession: S2/S4 (spring)→S2/S4 (summer)→S4 (autumn)→S2 (winter) in frequency of occurrence; S1 (spring)→S4 (summer)→S2 (autumn)→S1 (winter) in abundance. Bootstrapped average analysis showed a clear seasonal shift in body-size spectra of the protozoa during a 1-year cycle, and the best-matching analysis demonstrated that the temporal variations in frequency of occurrence and abundance were significantly correlated with water temperature, pH, dissolved oxygen (DO), alone or in combination with chemical oxygen demand (COD) and nutrients. Thus, the body-size spectra of biofilm-dwelling protozoa were seasonally shaped and might be used as a time and cost efficient bioindicator of water quality in marine ecosystems. Copyright © 2016 Elsevier GmbH. All rights reserved.

Stream temperature medelling and fibre optic distributed temperature sensing to quantify groundwater discharge in the Ngongotaha Stream, New Zealand

NASA Astrophysics Data System (ADS)

Moridnejad, Maryam; Cameron, Stewart; Shamseldin, Asaad; Ward, Nick Dudley; Verhagen, Floris

2015-04-01

To characterize stream/groundwater interaction, fibre optic distributed temperature sensing (FODTS) was deployed over a 1 km reach in the Ngongotaha Stream, Rotorua, New Zealand in January 2013. The cable was deployed at the streambed near the left and right banks as the groundwater fed springs discharge laterally at both banks. Temperature profiles measured by FODTS were used to identify the location of springs using a constant temperature method (20 min averaged temperature data) (Lowry et al., 2007; Matheswaran et al., 2014; Selker et al., 2006a) and a standard deviation of diurnal temperature method (Lowry et al., 2007; Matheswaran et al., 2014). Both methods identified 13 individual springs at the right and left banks in an approximately 115 m reach. The left and right bank temperature profiles showed that full mixing of the spring and stream water does not occur between most of the springs due to their close spacing. Groundwater discharge quantification based on FODTS data is typically made using a simple steady state thermal mixing model (Briggs et al., 2012a; Selker et al.,2006a; Westhoff et al., 2007). This formula is not applicable in streams like the Ngongotaha where springs are closely spaced and groundwater and surface water are not well mixed between springs. To address this issue, a new approach was developed in this study in which a one dimensional heat transport model was fitted to the FODTS measurements, where the main calibration parameters of interest were the unknown spring discharges. Datasets of measured temperatures at the left and right bank were transformed to a new single dataset using a weighted average where the weights reflect the degree of mixing downstream of a spring. Model calibration helped to find the optimum value of the weights in the springs section. For a spring on the left bank the weighted average was skewed towards the left bank data, and vice-versa for a right bank spring. Upstream of the spring section, a non-weighted average was applied. Streamflow gauging upstream and downstream of the study reach showed that the stream gains ~ 500 L/s from groundwater which was used to find the mixing ratios of the left and right banks. The new model allowed the spring discharge to be quantified in the complex hydrogeological setting. The results showed consistency with the findings of previous study in the Ngongotaha Stream catchment (Kov'ǎcov'a et al., 2008). Refrences Briggs, M. A., Lautz, L. K., McKenzie, J. M., 2012a. A comparison of fibre-optic distributed temperature sensing to traditional methods of evaluating groundwater inflow to streams. Hydrological Processes 26 (9), 1277-1290. Kov'ǎcov'a, E., White, P., (N.Z.), G. S., Staff, G. S. N., 2008. Groundwater Catchments for Individual Springs in Ngongotaha andWaiowhiro Surface Catchments, Lake Rotorua. GNS Science report. GNS Science. Lowry, C. S., Walker, J. F., Hunt, R. J., Anderson, M. P., 2007. Identifying spatial variability of groundwater discharge in a wetland stream using a distributed temperature sensor. Water Resources Research 43 (10). Matheswaran, K., Blemmer, M., Rosbjerg, D., Boegh, E., 2014. Seasonal variations in groundwater upwelling zones in a danish lowland stream analyzed using distributed temperature sensing (dts). Hydrological Processes 28 (3), 1422-1435. Selker, J., van de Giesen, N., Westhoff, M., Luxemburg, W., Parlange, M. B., 2006a. Fiber optics opens window on stream dynamics. Geophysical Research Letters 33 (24). Westhoff, M. C., Savenije, H. H. G., Luxemburg, W. M. J. ., Stelling, G. S., van de Giesen, N. C., Selker, J. S., Pfister, L., Uhlenbrook, S., 2007. A distributed stream temperature model using high resolution temperature observations. Hydrology and Earth System Sciences 11 (4), 1469-1480.

Role of Acclimatization in Weather-Related Human Mortality During the Transition Seasons of Autumn and Spring in a Thermally Extreme Mid-Latitude Continental Climate

PubMed Central

de Freitas, Christopher R.; Grigorieva, Elena A.

2015-01-01

Human mortality is closely related to natural climate-determined levels of thermal environmental stress and the resulting thermophysiological strain. Most climate-mortality research has focused on seasonal extremes during winter and summer when mortality is the highest, while relatively little attention has been paid to mortality during the transitional seasons of autumn and spring. The body acclimatizes to heat in the summer and cold in winter and readjusts through acclimatization during the transitions between the two during which time the body experiences the thermophysiological strain of readjustment. To better understand the influences of weather on mortality through the acclimatization process, the aim here is to examine the periods that link very cold and very warms seasons. The study uses the Acclimatization Thermal Strain Index (ATSI), which is a comparative measure of short-term thermophysiological impact on the body. ATSI centers on heat exchange with the body’s core via the respiratory system, which cannot be protected. The analysis is based on data for a major city in the climatic region of the Russian Far East characterized by very hot summers and extremely cold winters. The results show that although mortality peaks in winter (January) and is at its lowest in summer (August), there is not a smooth rise through autumn nor a smooth decline through spring. A secondary peak occurs in autumn (October) with a smaller jump in May. This suggests the acclimatization from warm-to-cold produces more thermophysiological strain than the transition from cold-to-warm. The study shows that ATSI is a useful metric for quantifying the extent to which biophysical adaptation plays a role in increased strain on the body during re-acclimatization and for this reason is a more appropriate climatic indictor than air temperature alone. The work gives useful bioclimatic information on risks involved in transitional seasons in regions characterized by climatic extremes. This could be handy in planning and managing health services to the public and measures that might be used to help mitigate impacts. PMID:26703633

Role of Acclimatization in Weather-Related Human Mortality During the Transition Seasons of Autumn and Spring in a Thermally Extreme Mid-Latitude Continental Climate.

PubMed

de Freitas, Christopher R; Grigorieva, Elena A

2015-11-26

Human mortality is closely related to natural climate-determined levels of thermal environmental stress and the resulting thermophysiological strain. Most climate-mortality research has focused on seasonal extremes during winter and summer when mortality is the highest, while relatively little attention has been paid to mortality during the transitional seasons of autumn and spring. The body acclimatizes to heat in the summer and cold in winter and readjusts through acclimatization during the transitions between the two during which time the body experiences the thermophysiological strain of readjustment. To better understand the influences of weather on mortality through the acclimatization process, the aim here is to examine the periods that link very cold and very warms seasons. The study uses the Acclimatization Thermal Strain Index (ATSI), which is a comparative measure of short-term thermophysiological impact on the body. ATSI centers on heat exchange with the body’s core via the respiratory system, which cannot be protected. The analysis is based on data for a major city in the climatic region of the Russian Far East characterized by very hot summers and extremely cold winters. The results show that although mortality peaks in winter (January) and is at its lowest in summer (August), there is not a smooth rise through autumn nor a smooth decline through spring. A secondary peak occurs in autumn (October) with a smaller jump in May. This suggests the acclimatization from warm-to-cold produces more thermophysiological strain than the transition from cold-to-warm. The study shows that ATSI is a useful metric for quantifying the extent to which biophysical adaptation plays a role in increased strain on the body during re-acclimatization and for this reason is a more appropriate climatic indictor than air temperature alone. The work gives useful bioclimatic information on risks involved in transitional seasons in regions characterized by climatic extremes. This could be handy in planning and managing health services to the public and measures that might be used to help mitigate impacts.

Spring-mediated distraction enterogenesis in-continuity.

PubMed

Huynh, Nhan; Rouch, Joshua D; Scott, Andrew; Chiang, Elvin; Wu, Benjamin M; Shekherdimian, Shant; Dunn, James C Y

2016-12-01

Distraction enterogenesis has been investigated as a novel treatment for patients with short bowel syndrome (SBS) but has been limited by loss of intestinal length during restoration and need for multiple bowel surgeries. The feasibility of in-continuity, spring-mediated intestinal lengthening has yet to be demonstrated. Juvenile mini-Yucatan pigs underwent in-continuity placement of polycaprolactone (PCL) degradable springs within jejunum. Methods used to anchor the spring ends to the intestine included full-thickness sutures and a high-friction surface spring. Spring constant (k) was 6-15N/m. Bowel was examined for length and presence of spring at 1 to 4weeks. Animals tolerated in-continuity lengthening without bowel obstruction for up to 29days. In-continuity jejunum with springs demonstrated intestinal lengthening by 1.47-fold ±0.11. Five springs had detached prematurely, and lengthening could not be assessed. Histologically, in-continuity jejunum showed significantly increased crypt depth and muscularis thickness in comparison to normal jejunum. Self-expanding endoluminal springs placed in continuity could lengthen intestine without obstruction in a porcine model. This is the first study showing safety and efficacy of a self-expanding endoluminal device for distraction enterogenesis. This is proof-of-concept that in-continuity spring lengthening is feasible and demonstrates its therapeutic potential in SBS. Level 3. Copyright © 2016 Elsevier Inc. All rights reserved.

Later springs green-up faster: the relation between onset and completion of green-up in deciduous forests of North America

NASA Astrophysics Data System (ADS)

Klosterman, Stephen; Hufkens, Koen; Richardson, Andrew D.

2018-05-01

In deciduous forests, spring leaf phenology controls the onset of numerous ecosystem functions. While most studies have focused on a single annual spring event, such as budburst, ecosystem functions like photosynthesis and transpiration increase gradually after budburst, as leaves grow to their mature size. Here, we examine the "velocity of green-up," or duration between budburst and leaf maturity, in deciduous forest ecosystems of eastern North America. We use a diverse data set that includes 301 site-years of phenocam data across a range of sites, as well as 22 years of direct ground observations of individual trees and 3 years of fine-scale high-frequency aerial photography, both from Harvard Forest. We find a significant association between later start of spring and faster green-up: - 0.47 ± 0.04 (slope ± 1 SE) days change in length of green-up for every day later start of spring within phenocam sites, - 0.31 ± 0.06 days/day for trees under direct observation, and - 1.61 ± 0.08 days/day spatially across fine-scale landscape units. To explore the climatic drivers of spring leaf development, we fit degree-day models to the observational data from Harvard Forest. We find that the default phenology parameters of the ecosystem model PnET make biased predictions of leaf initiation (39 days early) and maturity (13 days late) for red oak, while the optimized model has biases of 1 day or less. Springtime productivity predictions using optimized parameters are closer to results driven by observational data (within 1%) than those of the default parameterization (17% difference). Our study advances empirical understanding of the link between early and late spring phenophases and demonstrates that accurately modeling these transitions is important for simulating seasonal variation in ecosystem productivity.

The role of mechanical resonance in the neural control of swimming in fishes.

PubMed

Tytell, Eric D; Hsu, Chia-Yu; Fauci, Lisa J

2014-02-01

The bodies of many fishes are flexible, elastic structures; if you bend them, they spring back. Therefore, they should have a resonant frequency: a bending frequency at which the output amplitude is maximized for a particular input. Previous groups have hypothesized that swimming at this resonant frequency could maximize efficiency, and that a neural circuit called the central pattern generator might be able to entrain to a mechanical resonance. However, fishes swim in water, which may potentially damp out many resonant effects. Additionally, their bodies are elongated, which means that bending can occur in complicated ways along the length of the body. We review previous studies of the mechanical properties of fish bodies, and then present new data that demonstrate complex bending properties of elongated fish bodies. Resonant peaks in amplitude exist, but there may be many of them depending on the body wavelength. Additionally, they may not correspond to the maximum swimming speed. Next, we describe experiments using a closed-loop preparation of the lamprey, in which a preparation of the spinal cord is linked to a real-time simulation of the muscle and body properties, allowing us to examine resonance entrainment as we vary the simulated resonant frequency. We find that resonance entrainment does occur, but is rare. Gain had a significant, though weak, effect, and a nonlinear muscle model produced resonance entrainment more often than a linear filter. We speculate that resonance may not be a critical effect for efficient swimming in elongate, anguilliform swimmers, though it may be more important for stiffer carangiform and thunniform fishes. Copyright © 2014 Elsevier GmbH. All rights reserved.

Field estimates of body drag coefficient on the basis of dives in passerine birds.

PubMed

Hedenström, A; Liechti, F

2001-03-01

During forward flight, a bird's body generates drag that tends to decelerate its speed. By flapping its wings, or by converting potential energy into work if gliding, the bird produces both lift and thrust to balance the pull of gravity and drag. In flight mechanics, a dimensionless number, the body drag coefficient (C(D,par)), describes the magnitude of the drag caused by the body. The drag coefficient depends on the shape (or streamlining), the surface texture of the body and the Reynolds number. It is an important variable when using flight mechanical models to estimate the potential migratory flight range and characteristic flight speeds of birds. Previous wind tunnel measurements on dead, frozen bird bodies indicated that C(D,par) is 0.4 for small birds, while large birds should have lower values of approximately 0.2. More recent studies of a few birds flying in a wind tunnel suggested that previous values probably overestimated C(D,par). We measured maximum dive speeds of passerine birds during the spring migration across the western Mediterranean. When the birds reach their top speed, the pull of gravity should balance the drag of the body (and wings), giving us an opportunity to estimate C(D,par). Our results indicate that C(D,par) decreases with increasing Reynolds number within the range 0.17-0.77, with a mean C(D,par) of 0.37 for small passerines. A somewhat lower mean value could not be excluded because diving birds may control their speed below the theoretical maximum. Our measurements therefore support the notion that 0.4 (the 'old' default value) is a realistic value of C(D,par) for small passerines.

Applying spatial analysis techniques to assess the suitability of multipurpose uses of spring water in the Jiaosi Hot Spring Region, Taiwan

NASA Astrophysics Data System (ADS)

Jang, Cheng-Shin

2016-04-01

The Jiaosi Hot Spring Region is located in northeastern Taiwan and is rich in geothermal springs. The geothermal development of the Jiaosi Hot Spring Region dates back to the 18th century and currently, the spring water is processed for various uses, including irrigation, aquaculture, swimming, bathing, foot spas, and recreational tourism. Because of the proximity of the Jiaosi Hot Spring Region to the metropolitan area of Taipei City, the hot spring resources in this region attract millions of tourists annually. Recently, the Taiwan government is paying more attention to surveying the spring water temperatures in the Jiaosi Hot Spring Region because of the severe spring water overexploitation, causing a significant decline in spring water temperatures. Furthermore, the temperature of spring water is a reliable indicator for exploring the occurrence and evolution of springs and strongly affects hydrochemical reactions, components, and magnitudes. The multipurpose uses of spring water can be dictated by the temperature of the water. Therefore, accurately estimating the temperature distribution of the spring water is critical in the Jiaosi Hot Spring Region to facilitate the sustainable development and management of the multipurpose uses of the hot spring resources. To evaluate the suitability of spring water for these various uses, this study spatially characterized the spring water temperatures of the Jiaosi Hot Spring Region by using ordinary kriging (OK), sequential Gaussian simulation (SGS), and geographical information system (GIS). First, variogram analyses were used to determine the spatial variability of spring water temperatures. Next, OK and SGS were adopted to model the spatial distributions and uncertainty of the spring water temperatures. Finally, the land use (i.e., agriculture, dwelling, public land, and recreation) was determined and combined with the estimated distributions of the spring water temperatures using GIS. A suitable development strategy for the multipurpose uses of spring water is proposed according to the integration of the land use and spring water temperatures. The study results indicate that OK, SGS, and GIS are capable of characterizing spring water temperatures and the suitability of multipurpose uses of spring water. SGS realizations are more robust than OK estimates for characterizing spring water temperatures. Furthermore, current land use is almost ideal in the Jiaosi Hot Spring Region according to the estimated spatial pattern of spring water temperatures. Keywords: Hot spring; Temperature; Land use; Ordinary kriging; Sequential Gaussian simulation; Geographical information system

Modeling and Evaluation of Canted Coil Springs as High Temperature Seal Preloading Devices

NASA Technical Reports Server (NTRS)

Oswald, Jay J.; Mullen, Robert L.; Dunlap, Patrick H., Jr.; Steinetz, Bruce M.

2004-01-01

Future reusable launch vehicles will require advanced structural seals. This includes propulsion seals along edges and hinge lines in hypersonic engines, and control surface seals for movable flaps and elevons on proposed reentry vehicles. Seals must remain in sealing engagement with opposing surfaces, for multiple missions, even though the seal gap may be opening and closing due to thermal and structural loads. To meet this requirement either the seals themselves must be resilient or there must be a resilient structural element behind the seals. Case Western Reserve University is working with NASA s Glenn Research Center to develop more resilient high temperature seal components and preloading devices. Results are presented for a finite element analysis of a canted coil spring that is being considered as a high temperature seal preloading device. This type of spring is a leading candidate due to its ability to provide nearly constant force over a large deflection. The finite element analyses were verified by comparing them to experimental results of canted coil springs of three different stiffnesses, measured at Glenn Research Center. Once validated the parameterized model was combined with a scripting algorithm to assess the effects of key spring design variables (wire diameter, coils per inch, cant amplitude, eccentricity, and spring width) on spring stiffness and maximum Von Mises stress to aid in subsequent design.

Experimental determination of airplane mass and inertial characteristics

NASA Technical Reports Server (NTRS)

Wolowicz, C. H.; Yancey, R. B.

1974-01-01

Current practices are evaluated for experimentally determining airplane center of gravity, moments of inertia, and products of inertia. The techniques discussed are applicable to bodies other than airplanes. In pitching- and rolling-moment-of-inertia investigations with the airplane mounted on and pivoted about knife edges, the nonlinear spring moments that occur at large amplitudes of oscillation can be eliminated by using the proper spring configuration. The single-point suspension double-pendulum technique for obtaining yawing moments of inertia, products of inertia, and the inclination of the principal axis provides accurate results from yaw-mode oscillation data, provided that the sway-mode effects are minimized by proper suspension rig design. Rocking-mode effects in the data can be isolated.

Problems with the application of hydrogeological science to regulation of Australian mining projects: Carmichael Mine and Doongmabulla Springs

NASA Astrophysics Data System (ADS)

Currell, Matthew J.; Werner, Adrian D.; McGrath, Chris; Webb, John A.; Berkman, Michael

2017-05-01

Understanding and managing impacts from mining on groundwater-dependent ecosystems (GDEs) and other groundwater users requires development of defensible science supported by adequate field data. This usually leads to the creation of predictive models and analysis of the likely impacts of mining and their accompanying uncertainties. The identification, monitoring and management of impacts on GDEs are often a key component of mine approvals, which need to consider and attempt to minimise the risks that negative impacts may arise. Here we examine a case study where approval for a large mining project in Australia (Carmichael Coal Mine) was challenged in court on the basis that it may result in more extensive impacts on a GDE (Doongmabulla Springs) of high ecological and cultural significance than predicted by the proponent. We show that throughout the environmental assessment and approval process, significant data gaps and scientific uncertainties remained unresolved. Evidence shows that the assumed conceptual hydrogeological model for the springs could be incorrect, and that at least one alternative conceptualisation (that the springs are dependent on a deep fault) is consistent with the available field data. Assumptions made about changes to spring flow as a consequence of mine-induced drawdown also appear problematic, with significant implications for the spring-fed wetlands. Despite the large scale of the project, it appears that critical scientific data required to resolve uncertainties and construct robust models of the springs' relationship to the groundwater system were lacking at the time of approval, contributing to uncertainty and conflict. For this reason, we recommend changes to the approval process that would require a higher standard of scientific information to be collected and reviewed, particularly in relation to key environmental assets during the environmental impact assessment process in future projects.

Creating a Double-Spring Model to Teach Chromosome Movement during Mitosis & Meiosis

ERIC Educational Resources Information Center

Luo, Peigao

2012-01-01

The comprehension of chromosome movement during mitosis and meiosis is essential for understanding genetic transmission, but students often find this process difficult to grasp in a classroom setting. I propose a "double-spring model" that incorporates a physical demonstration and can be used as a teaching tool to help students understand this…

Wildfire risk and housing prices: a case study from Colorado Springs.

Treesearch

G.H. Donovan; P.A. Champ; D.T. Butry

2007-01-01

Unlike other natural hazards such as floods, hurricanes, and earthquakes, wildfire risk has not previously been examined using a hedonic property value model. In this article, we estimate a hedonic model based on parcel-level wildfire risk ratings from Colorado Springs. We found that providing homeowners with specific information about the wildfire risk rating of their...

Hydroclimate of the Spring Mountains and Sheep Range, Clark County, Nevada

USGS Publications Warehouse

Moreo, Michael T.; Senay, Gabriel B.; Flint, Alan L.; Damar, Nancy A.; Laczniak, Randell J.; Hurja, James

2014-01-01

Precipitation, potential evapotranspiration, and actual evapotranspiration often are used to characterize the hydroclimate of a region. Quantification of these parameters in mountainous terrains is difficult because limited access often hampers the collection of representative ground data. To fulfill a need to characterize ecological zones in the Spring Mountains and Sheep Range of southern Nevada, spatially and temporally explicit estimates of these hydroclimatic parameters are determined from remote-sensing and model-based methodologies. Parameter-elevation Regressions on Independent Slopes Model (PRISM) precipitation estimates for this area ranges from about 100 millimeters (mm) in the low elevations of the study area (700 meters [m]) to more than 700 mm in the high elevations of the Spring Mountains (> 2,800 m). The PRISM model underestimates precipitation by 7–15 percent based on a comparison with four high‑elevation precipitation gages having more than 20 years of record. Precipitation at 3,000-m elevation is 50 percent greater in the Spring Mountains than in the Sheep Range. The lesser amount of precipitation in the Sheep Range is attributed to partial moisture depletion by the Spring Mountains of eastward-moving, cool-season (October–April) storms. Cool-season storms account for 66–76 percent of annual precipitation. Potential evapotranspiration estimates by the Basin Characterization Model range from about 700 mm in the high elevations of the Spring Mountains to 1,600 mm in the low elevations of the study area. The model realistically simulates lower potential evapotranspiration on northeast-to-northwest facing slopes compared to adjacent southeast-to-southwest facing slopes. Actual evapotranspiration, estimated using a Moderate Resolution Imaging Spectroradiometer based water-balance model, ranges from about 100 to 600 mm. The magnitude and spatial variation of simulated, actual evapotranspiration was validated by comparison to PRISM precipitation. Estimated groundwater recharge, computed as the residual of precipitation depleted by actual evapotranspiration, is within the range of previous estimates. A climatic water deficit dataset and aridity-index-based climate zones are derived from precipitation and evapotranspiration datasets. Climate zones range from arid in the lower elevations of the study area to humid in small pockets on north- to northeast-facing slopes in the high elevations of the Spring Mountains. Correlative analyses between hydroclimatic variables and mean ecosystem elevations indicate that the climatic water deficit is the best predictor of ecosystem distribution (R2 = 0.92). Computed water balances indicate that substantially more recharge is generated in the Spring Mountains than in the Sheep Range. A geospatial database containing compiled and developed hydroclimatic data and other pertinent information accompanies this report.

Diffuse-flow conceptualization and simulation of the Edwards aquifer, San Antonio region, Texas

USGS Publications Warehouse

Lindgren, R.J.

2006-01-01

A numerical ground-water-flow model (hereinafter, the conduit-flow Edwards aquifer model) of the karstic Edwards aquifer in south-central Texas was developed for a previous study on the basis of a conceptualization emphasizing conduit development and conduit flow, and included simulating conduits as one-cell-wide, continuously connected features. Uncertainties regarding the degree to which conduits pervade the Edwards aquifer and influence ground-water flow, as well as other uncertainties inherent in simulating conduits, raised the question of whether a model based on the conduit-flow conceptualization was the optimum model for the Edwards aquifer. Accordingly, a model with an alternative hydraulic conductivity distribution without conduits was developed in a study conducted during 2004-05 by the U.S. Geological Survey, in cooperation with the San Antonio Water System. The hydraulic conductivity distribution for the modified Edwards aquifer model (hereinafter, the diffuse-flow Edwards aquifer model), based primarily on a conceptualization in which flow in the aquifer predominantly is through a network of numerous small fractures and openings, includes 38 zones, with hydraulic conductivities ranging from 3 to 50,000 feet per day. Revision of model input data for the diffuse-flow Edwards aquifer model was limited to changes in the simulated hydraulic conductivity distribution. The root-mean-square error for 144 target wells for the calibrated steady-state simulation for the diffuse-flow Edwards aquifer model is 20.9 feet. This error represents about 3 percent of the total head difference across the model area. The simulated springflows for Comal and San Marcos Springs for the calibrated steady-state simulation were within 2.4 and 15 percent of the median springflows for the two springs, respectively. The transient calibration period for the diffuse-flow Edwards aquifer model was 1947-2000, with 648 monthly stress periods, the same as for the conduit-flow Edwards aquifer model. The root-mean-square error for a period of drought (May-November 1956) for the calibrated transient simulation for 171 target wells is 33.4 feet, which represents about 5 percent of the total head difference across the model area. The root-mean-square error for a period of above-normal rainfall (November 1974-July 1975) for the calibrated transient simulation for 169 target wells is 25.8 feet, which represents about 4 percent of the total head difference across the model area. The root-mean-square error ranged from 6.3 to 30.4 feet in 12 target wells with long-term water-level measurements for varying periods during 1947-2000 for the calibrated transient simulation for the diffuse-flow Edwards aquifer model, and these errors represent 5.0 to 31.3 percent of the range in water-level fluctuations of each of those wells. The root-mean-square errors for the five major springs in the San Antonio segment of the aquifer for the calibrated transient simulation, as a percentage of the range of discharge fluctuations measured at the springs, varied from 7.2 percent for San Marcos Springs and 8.1 percent for Comal Springs to 28.8 percent for Leona Springs. The root-mean-square errors for hydraulic heads for the conduit-flow Edwards aquifer model are 27, 76, and 30 percent greater than those for the diffuse-flow Edwards aquifer model for the steady-state, drought, and above-normal rainfall synoptic time periods, respectively. The goodness-of-fit between measured and simulated springflows is similar for Comal, San Marcos, and Leona Springs for the diffuse-flow Edwards aquifer model and the conduit-flow Edwards aquifer model. The root-mean-square errors for Comal and Leona Springs were 15.6 and 21.3 percent less, respectively, whereas the root-mean-square error for San Marcos Springs was 3.3 percent greater for the diffuse-flow Edwards aquifer model compared to the conduit-flow Edwards aquifer model. The root-mean-square errors for San Antonio and San Pedro Springs were appreciably greater, 80.2 and 51.0 percent, respectively, for the diffuse-flow Edwards aquifer model. The simulated water budgets for the diffuse-flow Edwards aquifer model are similar to those for the conduit-flow Edwards aquifer model. Differences in percentage of total sources or discharges for a budget component are 2.0 percent or less for all budget components for the steady-state and transient simulations. The largest difference in terms of the magnitude of water budget components for the transient simulation for 1956 was a decrease of about 10,730 acre-feet per year (about 2 per-cent) in springflow for the diffuse-flow Edwards aquifer model compared to the conduit-flow Edwards aquifer model. This decrease in springflow (a water budget discharge) was largely offset by the decreased net loss of water from storage (a water budget source) of about 10,500 acre-feet per year.

Application of the line-spring model to a cylindrical shell containing a circumferential or axial part-through crack

NASA Technical Reports Server (NTRS)

Delale, F.; Erdogan, F.

1982-01-01

The line-spring model developed by Rice and Levy (1972) is used to obtain an approximate solution for a cylindrical shell containing a part-through surface crack. A Reissner type theory is used to account for the effects of the transverse shear deformations, and the stress intensity factor at the deepest penetration point of the crack is tabulated for bending and membrane loading by varying three-dimensionless length parameters of the problem formed from the shell radius, the shell thickness, the crack length, and the crack depth. The upper bounds of the stress intensity factors are provided, and qualitatively the line-spring model gives the expected results in comparison with elasticity solutions.

The Damper Spring Unit of the Sentinel 1 Solar Array

NASA Technical Reports Server (NTRS)

Doejaaren, Frans; Ellenbroek, Marcel

2012-01-01

The Damper Spring Unit (DSU, see Figure 1) has been designed to provide the damping required to control the deployment speed of the spring driven solar array deployment in an ARA Mk3 or FRED based Solar Array in situations where the standard application of a damper at the root-hinge is not feasible. The unit consists of four major parts: a main bracket, an eddy current damper, a spring unit, an actuation pulley which is coupled via Kevlar cables to a synchro-pulley of a hinge. The damper slows down the deployment speed and prevents deployment shocks at deployment completion. The spring unit includes 4 springs which overcome the resistances of the damper and the specific DSU control cable loop. This means it can be added to any spring driven deployment system without major modifications of that system. Engineering models of the Sentinel 1 solar array wing have been built to identify the deployment behavior, and to help to determine the optimal pulley ratios of the solar array and to finalize the DSU design. During the functional tests, the behavior proved to be very sensitive for the alignment of the DSU. This was therefore monitored carefully during the qualification program, especially prior to the TV cold testing. During TV "Cold" testing the measured retarding torque exceeded the max. required value: 284 N-mm versus the required 247 N-mm. Although this requirement was not met, the torque balance analysis shows that the 284 N-mm can be accepted, because the spring unit can provide 1.5 times more torque than required. Some functional tests of the DSU have been performed without the eddy current damper attached. It provided input data for the ADAMS solar array wing model. Simulation of the Sentinel-1 deployment (including DSU) in ADAMS allowed the actual wing deployment tests to be limited in both complexity and number of tests. The DSU for the Sentinel-1 solar array was successfully qualified and the flight models are in production.

Simulation of the recharge area for Frederick Springs, Dane County, Wisconsin

USGS Publications Warehouse

Hunt, R.J.; Steuer, J.J.

2000-01-01

Analysis of samples from the springs and a nearby municipal well identified large contrasts in chemistry, even for springs within 50 feet of one another. The differences were stable over time, were present in both ion and isotope analyses, and showed a distinct gradation from high nitrate, high calcium, Ordovician-carbonate dominated water in western spring vents to low nitrate, lower calcium, Cambrian-sandstone influenced water in eastern spring vents. The difference in chemistry was attributed to distinctive bedrock geology as demonstrated by overlaying the 50 percent probability capture zone over a bedrock geology map for the area. This finding gives additional confidence to the capture zone calculated by the ground-water flow model.

Determining the elastic properties of aptamer-ricin single molecule multiple pathway interactions

NASA Astrophysics Data System (ADS)

Wang, Bin; Park, Bosoon; Kwon, Yongkuk; Xu, Bingqian

2014-05-01

We report on the elastic properties of ricin and anti-ricin aptamer interactions, which showed three stable binding conformations, each of which has its special elastic properties. These different unbinding pathways were investigated by the dynamic force spectroscopy. A series-spring model combining the worm-like-chain model and Hook's law was used to estimate the apparent spring constants of the aptamer and linker molecule polyethylene glycol. The aptamer in its three different unbinding pathways showed different apparent spring constants. The two reaction barriers in the unbinding pathways also influence the apparent spring constant of the aptamer. This special elastic behavior of aptamer was used to distinguish its three unbinding pathways under different loading rates. This method also offered a way to distinguish and discard the non-specific interactions in single molecule experiments.

Spatial Characteristics of Geothermal Spring Temperatures and Discharge Rates in the Tatun Volcanic Area, Taiwan

NASA Astrophysics Data System (ADS)

Jang, C. S.; Liu, C. W.

2014-12-01

The Tatun volcanic area is the only potential volcanic geothermal region in the Taiwan island, and abundant in hot spring resources owing to stream water mixing with fumarolic gases. According to the Meinzer's classification, spring temperatures and discharge rates are the most important properties for characterizing spring classifications. This study attempted to spatially characterize spring temperatures and discharge rates in the Tatun volcanic area, Taiwanusing indicator kriging (IK). First, data on spring temperatures and discharge rates, which were collected from surveyed data of the Taipei City Government, were divided into high, moderate and low categories according to spring classification criteria, and the various categories were regarded as estimation thresholds. Then, IK was adopted to model occurrence probabilities of specified temperatures and discharge rates in springs, and to determine their classifications based on estimated probabilities. Finally, nine combinations were obtained from the classifications of temperatures and discharge rates in springs. Moreover, the combinations and features of spring water were spatially quantified according to seven sub-zones of spring utilization. A suitable and sustainable development strategy of the spring area was proposed in each sub-zone based on probability-based combinations and features of spring water.The research results reveal that the probability-based classifications using IK provide an excellent insight in exploring the uncertainty of spatial features in springs, and can provide Taiwanese government administrators with detailed information on sustainable spring utilization and conservation in the overexploited spring tourism areas. The sub-zones BT (Beitou), RXY (Rd. Xingyi), ZSL (Zhongshanlou) and LSK (Lengshuikeng) with high or moderate discharge rates are suitable to supply spring water for tourism hotels.Local natural hot springs should be planned in the sub-zones DBT (Dingbeitou), ZSL, XYK (Xiayoukeng), and MC (Macao) with low discharge rates, and low or moderate temperatures, particularly in riverbeds or valleys.Keywords: Spring; Temperature; Discharge rate; Indicator kriging; Uncertainty

Reproductive strategies and seasonal changes in the somatic indices of seven small-bodied fishes in Atlantic Canada in relation to study design for environmental effects monitoring.

PubMed

Barrett, Timothy J; Brasfield, Sandra M; Carroll, Leslie C; Doyle, Meghan A; van den Heuvel, Michael R; Munkittrick, Kelly R

2015-05-01

Small-bodied fishes are more commonly being used in environmental effects monitoring (EEM) studies. There is a lack of understanding of the biological characteristics of many small-bodied species, which hinders study designs for monitoring studies. For example, 72% of fish population surveys in Canada's EEM program for pulp and paper mills that used small-bodied fishes were conducted outside of the reproductive period of the species. This resulted in an inadequate assessment of the EEM program's primary effect endpoint (reproduction) for these studies. The present study examined seasonal changes in liver size, gonad size, and condition in seven freshwater and estuarine small-bodied fishes in Atlantic Canada. These data were used to examine differences in reproductive strategies and patterns of energy storage among species. Female gonadal recrudescence in all seven species began primarily in the 2-month period in the spring before spawning. Male gonadal development was concurrent with females in five species; however, gonadal recrudescence began in the fall in male three-spined stickleback (Gasterosteus aculeatus) and slimy sculpin (Cottus cognatus). The spawning period for each species was estimated from the decline in relative ovary size after its seasonal maximum value in spring. The duration of the spawning period reflected the reproductive strategy (single vs multiple spawning) of the species. Optimal sampling periods to assess reproductive impacts in each species were determined based on seasonal changes in ovary size and were identified to be during the prespawning period when gonads are developing and variability in relative gonad size is at a minimum.

Episodic sediment-discharge events in Cascade Springs, southern Black Hills, South Dakota

USGS Publications Warehouse

Hayes, Timothy Scott

1999-01-01

Cascade Springs is a group of artesian springs in the southern Black Hills, South Dakota, with collective flow of about 19.6 cubic feet per second. Beginning on February 28, 1992, a large discharge of red suspended sediment was observed from two of the six known discharge points. Similar events during 1906-07 and 1969 were documented by local residents and newspaper accounts. Mineralogic and grain-size analyses were performed to identify probable subsurface sources of the sediment. Geochemical modeling was performed to evaluate the geochemical evolution of water discharged from Cascade Springs. Interpretations of results provide a perspective on the role of artesian springs in the regional geohydrologic framework. X-ray diffraction mineralogic analyses of the clay fraction of the suspended sediment were compared to analyses of clay-fraction samples taken from nine geologic units at and stratigraphically below the spring-discharge points. Ongoing development of a subsurface breccia pipe(s) in the upper Minnelusa Formation and/or Opeche Shale was identified as a likely source of the suspended sediment; thus, exposed breccia pipes in lower Hell Canyon were examined. Upper Minnelusa Formation breccia pipes in lower Hell Canyon occur in clusters similar to the discrete discharge points of Cascade Springs. Grain-size analyses showed that breccia masses lack clay fractions and have coarser distributions than the wall rocks, which indicates that the red, fine-grained fractions have been carried out as suspended sediment. These findings support the hypothesis that many breccia pipes were formed as throats of abandoned artesian springs. Geochemical modeling was used to test whether geochemical evolution of ground water is consistent with this hypothesis. The evolution of water at Cascade Springs could not be suitably simulated using only upgradient water from the Minnelusa aquifer. A suitable model involved dissolution of anhydrite accompanied by dedolomitization in the upper Minnelusa Formation, which is caused by upward leakage of relatively fresh water from the Madison aquifer. The anhydrite dissolution and dedolomitization account for the net removal of minerals that would lead to breccia pipe formation by gravitational collapse. Breccia pipes in the lower Minnelusa Formation are uncommon; however, networks of interconnected breccia layers and breccia dikes are common. These networks, along with vertical fractures and faults, are likely pathways for transmitting upward leakage from the Madison aquifer. It is concluded that suspended sediment discharged at Cascade Springs probably results from episodic collapse brecciation that is caused by subsurface dissolution of anhydrite beds and cements of the upper Minnelusa Formation, accompanied by replacement of dolomite by calcite. It is further concluded that many breccia pipes probably are the throats of artesian springs that have been abandoned and exposed by erosion. The locations of artesian spring-discharge points probably have been shifting outwards from the center of the Black Hills uplift, essentially keeping pace with regional erosion over geologic time. Thus, artesian springflow probably is a factor in controlling water levels in the Madison and Minnelusa aquifers, with hydraulic head declining over geologic time, in response to development of new discharge points. Development of breccia pipes as throats of artesian springs would greatly enhance vertical hydraulic conductivity in the immediate vicinity of spring-discharge points. Horizontal hydraulic conductivity in the Minnelusa Formation also may be enhanced by dissolution processes related to upward leakage from the Madison aquifer. Potential processes could include dissolution resulting from leakage in the vicinity of breccia pipes that are abandoned spring throats, active spring discharge, development of subsurface breccias with no visible surface expression or spring discharge, as well as general areal leakage

Magnetic Check Valve

NASA Technical Reports Server (NTRS)

Morris, Brian G.; Bozeman, Richard J., Jr.

1994-01-01

Poppet in proposed check valve restored to closed condition by magnetic attraction instead of spring force. Oscillations suppressed, with consequent reduction of wear. Stationary magnetic disk mounted just upstream of poppet, also containing magnet. Valve body nonmagnetic. Forward pressure or flow would push poppet away from stationary magnetic disk so fluid flows easily around poppet. Stop in valve body prevents poppet from being swept away. When flow stopped or started to reverse, magnetic attraction draws poppet back to disk. Poppet then engages floating O-ring, thereby closing valve and preventing reverse flow. Floating O-ring facilitates sealing at low loads.

Influence of Locally Derived Recharge on the Water Quality and Temperature of Springs in Hot Springs National Park, Arkansas

USGS Publications Warehouse

Bell, Richard W.; Hays, Phillip D.

2007-01-01

The hot springs of Hot Springs National Park consist of a mixture of water from two recharge components: a primary hot-water component and a secondary cold-water component. Widespread distribution of fractures enables mixing of the hot- and cold-water components of flow near the discharge area for the springs. Urbanization in the area near the hot springs of Hot Springs National Park has increased the potential for degradation of the quality of surface-water runoff and locally derived ground-water recharge to the hot springs. Previous studies by the U.S. Geological Survey have indicated that water from some cold-water springs and wells in the vicinity of Hot Springs, Arkansas, showed evidence of contamination and that water from locally derived cold-water recharge might contribute 25 percent of the total flow to the hot springs after storms. Water samples were collected during base-flow conditions at nine hot springs and two cold-water springs in September 2000. Nine hot springs and one cold-water spring were resampled in October 2001 after a storm that resulted in a measurable decrease in water temperature in selected hot springs. Water samples were analyzed for a variety of dissolved chemical constituents (nutrients, major ions, trace elements, pesticides, semivolatile compounds, isotopes, and radiochemicals), physical properties, field measurements, and bacteria. Comparison of analyses of samples collected during base-flow conditions from the springs in 2000 and during a storm event in 2001 with the results from earlier studies dating back to the late 1800's indicates that little change in major, minor, and trace constituent chemistry has occurred and that the water continues to be of excellent quality. Water-quality data show distinguishable differences in water chemistry of the springs during base-flow and stormflow conditions, indicating changing input of cold-water recharge relative to hot-water recharge. Silica, total dissolved solids, strontium, barium, and sulfate show statistically significant differences between the median values of base-flow and stormflow samples. While variations in these constituents do not degrade water quality, the differences do provide evidence of variability in the factors controlling water quality of the hot springs and show that water quality is influenced by the locally derived, cold-water component of flow to the springs. Water temperature was measured continuously (3-minute intervals) between August 2000 and October 2002 at four hot springs. Continuous water-temperature data at the springs provide no indication of persistent long-term change in water temperature through time. Short time-scale water-temperature decreases occur in response to mixing of hot-springs water with locally derived recharge after storm events; the magnitude of these decreases varied inversely with the amount of rainfall. Maximum decreases in water temperature for specific storms had a non-linear relation with the amount of precipitation measured for the events. Response time for water temperature to begin decreasing from baseline temperature as a result of storm recharge was highly variable. Some springs began decreasing from baseline temperature as quickly as 1 hour after the beginning of a storm; one spring had an 8-hour minimum response time to show a storm-related temperature decrease. Water-quality, water-temperature, isotopic, and radiochemical data provide multiple lines of evidence supporting the importance of the contribution of cold-water recharge to hot springs. All the springs sampled indicated some measure of influence from local recharge. Binary mixing models using silica and total dissolved solids indicate that cold-water recharge from stormflow contributes an estimated 10 to 31 percent of the flow of hot springs. Models using water temperature indicate that cold-water recharge from stormflow contributes an estimated 1 to 35 percent of the flow of the various hot springs. Alth

Portrayal of tanning, clothing fashion and shade use in Australian women's magazines, 1987-2005.

PubMed

Dixon, Helen; Dobbinson, Suzanne; Wakefield, Melanie; Jamsen, Kris; McLeod, Kim

2008-10-01

To examine modelling of outcomes relevant to sun protection in Australian women's magazines, content analysis was performed on 538 spring and summer issues of popular women's magazines from 1987 to 2005. A total of 4949 full-colour images of Caucasian females were coded for depth of tan, extent of clothing cover, use of shade and setting. Logistic regression using robust standard errors to adjust for clustering on magazine was used to assess the relationship between these outcomes and year, setting and model's physical characteristics. Most models portrayed outdoors did not wear hats (89%) and were not in shade (87%). Between 1987 and 2005, the proportion of models depicted wearing hats decreased and the proportion of models portrayed with moderate to dark tans declined and then later increased. Younger women were more likely to be portrayed with a darker tan and more of their body exposed. Models with more susceptible phenotypes (paler hair and eye colour) were less likely to be depicted with a darker tan. Darker tans and poor sun-protective behaviour were most common among models depicted at beaches/pools. Implicit messages about sun protection in popular Australian women's magazines contradict public health messages concerning skin cancer prevention.

Periodic solutions of a spring-pendulum system.

NASA Technical Reports Server (NTRS)

Broucke, R.; Baxa, P. A.

1973-01-01

A study has been made of a dynamical system composed of a pendulum and a harmonic oscillator, in order to show the remarkable resemblance with many classical celestial mechanics problems, in particular, the restricted three-body problem. It is shown that the well-known investigations of periodic orbits can be applied to the present dynamics problem.

PEO Ammunition Systems Portfolio Book 2012-2013

DTIC Science & Technology

2011-02-02

assembly. Aluminum ogive contains firing pin, a rubber anti-creep spring and M550 fuze escapement assembly and is threaded to projectile body...51 The Mortar Weapons and Fire Control Family M95/M96 Mortar Fire Control System (MFCS) – Mounted...52 M150/M151 Mortar Fire Control System Dismounted (MFCS-D

Overweight and Obesity in Lesbian and Bisexual College Women

ERIC Educational Resources Information Center

Struble, Corrie Barnett; Lindley, Lisa L.; Montgomery, Kara; Hardin, James; Burcin, Michelle

2010-01-01

Objective: To estimate and compare the prevalence of overweight and obesity among self-identified lesbian, bisexual, and heterosexual college age women. Methods: A secondary analysis of the Spring 2006 National College Health Assessment was conducted with 31,500 female college students (aged 18 to 25 years) to compare body mass index (calculated…

A Profile and Analysis of Major Departments of Slavic Languages and Literatures

ERIC Educational Resources Information Center

Millar, Gera A.

1976-01-01

A survey is reported investigating the outlook of teachers and administrators on the growth potential of the field of Slavic languages and literature and providing a body of data on major programs in the United States. A questionnaire was mailed to the heads of 26 departments in spring 1975. (RM)

77 FR 75972 - Foreign-Trade Zone 26 - Atlanta, Georgia Notification of Proposed Production Activity Suzuki Mfg...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... able to choose the duty rate during customs entry procedures that apply to ATVs and related components... include: articles of rubber, hoses, gaskets, washers, fasteners, springs, sign plates/ labels, brackets, plates, braces, fittings, body parts, engines and related parts, pumps, fans, valves, hose/pipe...

Factors affecting ground-water quality in Oakland County, Michigan

USGS Publications Warehouse

,

2004-01-01

Ground water is water stored in pores within soil and rock beneath the land surface. When these pores are connected so that water can be transmitted to wells or springs, these bodies of soil and rock are termed aquifers, from two Greek words meaning “water” and “to bear.” 

Continuous chain bit with downhole cycling capability

DOEpatents

Ritter, Don F.; St. Clair, Jack A.; Togami, Henry K.

1983-01-01

A continuous chain bit for hard rock drilling is capable of downhole cycling. A drill head assembly moves axially relative to a support body while the chain on the head assembly is held in position so that the bodily movement of the chain cycles the chain to present new composite links for drilling. A pair of spring fingers on opposite sides of the chain hold the chain against movement. The chain is held in tension by a spring-biased tensioning bar. A head at the working end of the chain supports the working links. The chain is centered by a reversing pawl and piston actuated by the pressure of the drilling mud. Detent pins lock the head assembly with respect to the support body and are also operated by the drilling mud pressure. A restricted nozzle with a divergent outlet sprays drilling mud into the cavity to remove debris. Indication of the centered position of the chain is provided by noting a low pressure reading indicating proper alignment of drilling mud slots on the links with the corresponding feed branches.

Early snowmelt significantly enhances boreal springtime carbon uptake

PubMed Central

Pulliainen, Jouni; Aurela, Mika; Laurila, Tuomas; Aalto, Tuula; Takala, Matias; Salminen, Miia; Kulmala, Markku; Barr, Alan; Heimann, Martin; Lindroth, Anders; Laaksonen, Ari; Derksen, Chris; Mäkelä, Annikki; Markkanen, Tiina; Lemmetyinen, Juha; Susiluoto, Jouni; Dengel, Sigrid; Mammarella, Ivan; Tuovinen, Juha-Pekka; Vesala, Timo

2017-01-01

We determine the annual timing of spring recovery from space-borne microwave radiometer observations across northern hemisphere boreal evergreen forests for 1979–2014. We find a trend of advanced spring recovery of carbon uptake for this period, with a total average shift of 8.1 d (2.3 d/decade). We use this trend to estimate the corresponding changes in gross primary production (GPP) by applying in situ carbon flux observations. Micrometeorological CO2 measurements at four sites in northern Europe and North America indicate that such an advance in spring recovery would have increased the January–June GPP sum by 29 g⋅C⋅m−2 [8.4 g⋅C⋅m−2 (3.7%)/decade]. We find this sensitivity of the measured springtime GPP to the spring recovery to be in accordance with the corresponding sensitivity derived from simulations with a land ecosystem model coupled to a global circulation model. The model-predicted increase in springtime cumulative GPP was 0.035 Pg/decade [15.5 g⋅C⋅m−2 (6.8%)/decade] for Eurasian forests and 0.017 Pg/decade for forests in North America [9.8 g⋅C⋅m−2 (4.4%)/decade]. This change in the springtime sum of GPP related to the timing of spring snowmelt is quantified here for boreal evergreen forests. PMID:28973918

Effects of artificial-recharge experiments at Ship Creek alluvial fan on water levels at Spring Acres Subdivision, Anchorage, Alaska

USGS Publications Warehouse

Meyer, William; Patrick, Leslie

1980-01-01

The effect of the artificial recharge experiments on water levels at Spring Acres subdivision, Anchorage, Alaska, was evaluated using two digital models constructed to simulate groundwater movement and water-level rises induced by the artificial recharge. The models predicted that the artificial recharge would have caused water levels in the aquifer immediately underlying Spring Acres subdivision to rise 0.2 foot from May 20 to August 7, 1975. The models also predicted a total rise in groundwater levels of 1.1 feet at this location from July 16, 1973 to August 7, 1975, as a result of the artificial-recharge experiments. Water-level data collected from auger holes in March 1975 by a consulting firm for the contractor indicated a depth to water of 6-7 feet below land surface at Spring Acres subdivision at this time. Water levels measured in and near Spring Acres subdivision several years before and after the 1973-75 artificial-recharge experiments showed seasonal rises of 2 to 12.4 feet. A depth to water below land surface of 2.6 feet was measured 600 feet from the subdivision in 1971 and in the subdivision in 1977. Average measured depth to water in the area was 7.0 feet from early 1976 to September 1979. (USGS)

An efficient biological pathway layout algorithm combining grid-layout and spring embedder for complicated cellular location information

PubMed Central

2010-01-01

Background Graph drawing is one of the important techniques for understanding biological regulations in a cell or among cells at the pathway level. Among many available layout algorithms, the spring embedder algorithm is widely used not only for pathway drawing but also for circuit placement and www visualization and so on because of the harmonized appearance of its results. For pathway drawing, location information is essential for its comprehension. However, complex shapes need to be taken into account when torus-shaped location information such as nuclear inner membrane, nuclear outer membrane, and plasma membrane is considered. Unfortunately, the spring embedder algorithm cannot easily handle such information. In addition, crossings between edges and nodes are usually not considered explicitly. Results We proposed a new grid-layout algorithm based on the spring embedder algorithm that can handle location information and provide layouts with harmonized appearance. In grid-layout algorithms, the mapping of nodes to grid points that minimizes a cost function is searched. By imposing positional constraints on grid points, location information including complex shapes can be easily considered. Our layout algorithm includes the spring embedder cost as a component of the cost function. We further extend the layout algorithm to enable dynamic update of the positions and sizes of compartments at each step. Conclusions The new spring embedder-based grid-layout algorithm and a spring embedder algorithm are applied to three biological pathways; endothelial cell model, Fas-induced apoptosis model, and C. elegans cell fate simulation model. From the positional constraints, all the results of our algorithm satisfy location information, and hence, more comprehensible layouts are obtained as compared to the spring embedder algorithm. From the comparison of the number of crossings, the results of the grid-layout-based algorithm tend to contain more crossings than those of the spring embedder algorithm due to the positional constraints. For a fair comparison, we also apply our proposed method without positional constraints. This comparison shows that these results contain less crossings than those of the spring embedder algorithm. We also compared layouts of the proposed algorithm with and without compartment update and verified that latter can reach better local optima. PMID:20565884

Spring Break versus Spring Broken: Predictive Utility of Spring Break Alcohol Intentions and Willingness at Varying Levels of Extremity

PubMed Central

Litt, Dana M.; Lewis, Melissa A.; Patrick, Megan E.; Rodriguez, Lindsey; Neighbors, Clayton; Kaysen, Debra L.

2013-01-01

Objective Within the domain of risk-related behavior, many times the decision to engage is not a product of premeditation or intention. The Prototype Willingness model was created to capture and explain the unintended element of risk behavior. The present study aimed to evaluate the importance of willingness versus intention, two important constructs within the Prototype Willingness model, in relation to Spring Break drinking behavior when assessed at both high and low extremities. Method College undergraduates (N = 275) completed questionnaires prior to Spring Break regarding their anticipated Spring Break activities. Willingness and intention were assessed for different levels of risk. Specifically, participants indicated the extent to which they intended to (a) get drunk and (b) drink enough to black out or pass out; and the extent to which they were willing to (a) get drunk and (b) drink enough to black out or pass out. When classes resumed following Spring Break, the students indicated the extent to which they actually (a) got drunk and (b) drank enough to black out or pass out. Results Results demonstrated that when the health-related risk was lower (i.e., getting drunk), intention was a stronger predictor of behavior than was willingness. However, as the level of risk increased (i.e., getting drunk enough to black out or pass out), willingness more strongly predicted behavior. Conclusion The present study suggests that willingness and intentions differentially predict Spring Break alcohol-related behavior depending on the extremity of behavior in question. Implications regarding alcohol interventions are discussed. PMID:23404667

Residence times and age distributions of spring waters at the Semmering catchment area, Eastern Austria, as inferred from tritium, CFCs and stable isotopes.

PubMed

Han, Liangfeng; Hacker, Peter; Gröning, Manfred

2007-03-01

The groundwater system in the mountainous area of Semmering, Austria, was studied by environmental tracers in several karst springs. The tracers used included stable isotopes ((18)O, (2)H), tritium ((3)H) and chlorofluorocarbons (CFCs). The tracers provided valuable information in regard to (1) the mean altitude of the spring catchment areas; (2) the residence time and age distribution of the spring waters; and (3) the interconnection of the springs to a sinkhole. The combination of the stable isotopic data and the topography/geology provided the estimates of the mean altitudes of the catchment areas. Based on the stable isotopic data the recharge temperature of the spring waters was estimated. The smoothing of precipitation's isotopic signal in spring discharge provided information on the minimum transit time of the spring waters. Due to short observation time, (3)H data alone cannot be used for describing the mean residence time of the karst waters. CFCs, though useful in recognizing the co-existence of young (post-1993) water with old (CFC-free) water, could not be used to resolve age distribution models. It is shown in this article, however, that the combined use of tritium and CFCs can provide a better assessment of models to account for different groundwater age distributions. In Appendix A, a simplified method for collecting groundwater samples for the analysis of CFCs is described. The method provides a real facilitation for fieldwork. Test data are given for this sampling method in regard to potential contamination by atmospheric CFCs.

Geology and Conceptual Model of the Domuyo Geothermal Area, Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Fragoso, A. S.; Ferrari, L.; Norini, G.

2017-12-01

Cerro Domuyo is the highest mountain in Patagonia and its western slope is characterized by thermal springs with boiling fluids as well as silicic domes and pyroclastic deposits that suggest the existence of a geothermal reservoir. Early studies proposed that the thermal springs were fault-controlled and the reservoir was located in a graben bounded by E-W normal faults. A recent geochemical study estimated a temperature of 220ºC for the fluid reservoir and a thermal energy release of 1.1 GW, one of the world largest advective heat flux from a continental volcanic center. We carried out a geologic survey and U-Pb and U-Th geochronologic study to elaborate an updated conceptual model for the Domuyo geothermal area. Our study indicates that the Domuyo Volcanic Complex (DVC) is a dome complex overlying an older, Middle Miocene to Pliocene volcanic sequence widely exposed to the southwest and to the north, which in turn covers: 1) the Jurassice-Early Creteacoeus Neuquen marine sedimentary succession, 2) silicic ignimbrites dated at 186.7 Ma and, 3) the Paleozoic metamorphic basement intruded by 288 Ma granite bodies. These pre-Cenozoic successions are involved in dominantly N-S trending folds and thrust faults later displaced by E-W striking normal faults with a right lateral component of motion that underlie the DVC. The volcanic cycle forming the DVC is distinctly bimodal with the emplacement of massive silicic domes but also less voluminous olivine basalts on its southern slope. The central dome underwent a major collapse that produced 0.35 km3 of ash and block flow and associated pyroclastic flows that filled the valley to the southwest up to 30 km from the source. This was followed by a voluminous effusive activity that formed silicic domes dated between 254-322 Ky, which is inferred to overlain a partially molten silicic magma chamber. Integrating the geologic model with magnetotelluric and gravity surveys we developed a conceptual model of the geothermal system in which the reservoir is inferred at a depth of less than 2 km in pre-Pliocene fractured rocks, bounded by E-W faults and sealed by the pyroclastic deposits and rhyolitic lavas of the DVC. The location of most thermal springs is not controlled by faults. Rather, they are lateral flows emerging at the contact between the fractured basement and the caprock.

Preliminary Study on Ground-Magnetic Data Near the Active Volcanoes in Konga Bay, East Flores Indonesia

NASA Astrophysics Data System (ADS)

Laesanpura, Agus; Dahrin, Darharta; Nurseptian, Ivan

2017-04-01

East Flores is part of Nusa Tenggara island belongs to volcanic arc zone, hence the active volcanoes surround the area about 60 × 50 square km. It is located at latitude south 8° 30’, and longitude east 122° 45’. Geologically, the rock is mostly of volcanic material since Miocene age. The Intriguing question is where the volcanic feeder, pyroclastic, and how it vanish in subsurface. The magnetic data acquisitions were executed on land for 500 meter interval and denser through the bay surrounded by volcanoes. The combine reduction to pole and forward modelling is apply for serve interpretation using forward modelling technique. The two interpretation sections, show the body of magmatic may present at depth about 2 to 3 km. The observation show no significant decreasing or loosening of magnetic anomaly although near the active volcano. We suggest the thermal anomaly is just disturbing magnetic data in near surface but not in the depth one. Meanwhile the reduction to pole’s section could distinguish the two group of rock. In assuming the layer is flat. The inferred peak of magmatic body near the existing volcano; and the active demagnetization associated through evidence of hot spring and inferred fault structure.

Walking in circles: a modelling approach

PubMed Central

Maus, Horst-Moritz; Seyfarth, Andre

2014-01-01

Blindfolded or disoriented people have the tendency to walk in circles rather than on a straight line even if they wanted to. Here, we use a minimalistic walking model to examine this phenomenon. The bipedal spring-loaded inverted pendulum exhibits asymptotically stable gaits with centre of mass (CoM) dynamics and ground reaction forces similar to human walking in the sagittal plane. We extend this model into three dimensions, and show that stable walking patterns persist if the leg is aligned with respect to the body (here: CoM velocity) instead of a world reference frame. Further, we demonstrate that asymmetric leg configurations, which are common in humans, will typically lead to walking in circles. The diameter of these circles depends strongly on parameter configuration, but is in line with empirical data from human walkers. Simulation results suggest that walking radius and especially direction of rotation are highly dependent on leg configuration and walking velocity, which explains inconsistent veering behaviour in repeated trials in human data. Finally, we discuss the relation between findings in the model and implications for human walking. PMID:25056215

Regional groundwater-flow model of the Redwall-Muav, Coconino, and alluvial basin aquifer systems of northern and central Arizona

USGS Publications Warehouse

Pool, D.R.; Blasch, Kyle W.; Callegary, James B.; Leake, Stanley A.; Graser, Leslie F.

2011-01-01

A numerical flow model (MODFLOW) of the groundwater flow system in the primary aquifers in northern Arizona was developed to simulate interactions between the aquifers, perennial streams, and springs for predevelopment and transient conditions during 1910 through 2005. Simulated aquifers include the Redwall-Muav, Coconino, and basin-fill aquifers. Perennial stream reaches and springs that derive base flow from the aquifers were simulated, including the Colorado River, Little Colorado River, Salt River, Verde River, and perennial reaches of tributary streams. Simulated major springs include Blue Spring, Del Rio Springs, Havasu Springs, Verde River headwater springs, several springs that discharge adjacent to major Verde River tributaries, and many springs that discharge to the Colorado River. Estimates of aquifer hydraulic properties and groundwater budgets were developed from published reports and groundwater-flow models. Spatial extents of aquifers and confining units were developed from geologic data, geophysical models, a groundwater-flow model for the Prescott Active Management Area, drill logs, geologic logs, and geophysical logs. Spatial and temporal distributions of natural recharge were developed by using a water-balance model that estimates recharge from direct infiltration. Additional natural recharge from ephemeral channel infiltration was simulated in alluvial basins. Recharge at wastewater treatment facilities and incidental recharge at agricultural fields and golf courses were also simulated. Estimates of predevelopment rates of groundwater discharge to streams, springs, and evapotranspiration by phreatophytes were derived from previous reports and on the basis of streamflow records at gages. Annual estimates of groundwater withdrawals for agriculture, municipal, industrial, and domestic uses were developed from several sources, including reported withdrawals for nonexempt wells, estimated crop requirements for agricultural wells, and estimated per capita water use for exempt wells. Accuracy of the simulated groundwater-flow system was evaluated by using observational control from water levels in wells, estimates of base flow from streamflow records, and estimates of spring discharge. Major results from the simulations include the importance of variations in recharge rates throughout the study area and recharge along ephemeral and losing stream reaches in alluvial basins. Insights about the groundwater-flow systems in individual basins include the hydrologic influence of geologic structures in some areas and that stream-aquifer interactions along the lower part of the Little Colorado River are an effective control on water level distributions throughout the Little Colorado River Plateau basin. Better information on several aspects of the groundwater flow system are needed to reduce uncertainty of the simulated system. Many areas lack documentation of the response of the groundwater system to changes in withdrawals and recharge. Data needed to define groundwater flow between vertically adjacent water-bearing units is lacking in many areas. Distributions of recharge along losing stream reaches are poorly defined. Extents of aquifers and alluvial lithologies are poorly defined in parts of the Big Chino and Verde Valley sub-basins. Aquifer storage properties are poorly defined throughout most of the study area. Little data exist to define the hydrologic importance of geologic structures such as faults and fractures. Discharge of regional groundwater flow to the Verde River is difficult to identify in the Verde Valley sub-basin because of unknown contributions from deep percolation of excess surface water irrigation.

Application of dimensionless sediment rating curves to predict suspended-sediment concentrations, bedload, and annual sediment loads for rivers in Minnesota

USGS Publications Warehouse

Ellison, Christopher A.; Groten, Joel T.; Lorenz, David L.; Koller, Karl S.

2016-10-27

Consistent and reliable sediment data are needed by Federal, State, and local government agencies responsible for monitoring water quality, planning river restoration, quantifying sediment budgets, and evaluating the effectiveness of sediment reduction strategies. Heightened concerns about excessive sediment in rivers and the challenge to reduce costs and eliminate data gaps has guided Federal and State interests in pursuing alternative methods for measuring suspended and bedload sediment. Simple and dependable data collection and estimation techniques are needed to generate hydraulic and water-quality information for areas where data are unavailable or difficult to collect.The U.S. Geological Survey, in cooperation with the Minnesota Pollution Control Agency and the Minnesota Department of Natural Resources, completed a study to evaluate the use of dimensionless sediment rating curves (DSRCs) to accurately predict suspended-sediment concentrations (SSCs), bedload, and annual sediment loads for selected rivers and streams in Minnesota based on data collected during 2007 through 2013. This study included the application of DSRC models developed for a small group of streams located in the San Juan River Basin near Pagosa Springs in southwestern Colorado to rivers in Minnesota. Regionally based DSRC models for Minnesota also were developed and compared to DSRC models from Pagosa Springs, Colorado, to evaluate which model provided more accurate predictions of SSCs and bedload in Minnesota.Multiple measures of goodness-of-fit were developed to assess the effectiveness of DSRC models in predicting SSC and bedload for rivers in Minnesota. More than 600 dimensionless ratio values of SSC, bedload, and streamflow were evaluated and delineated according to Pfankuch stream stability categories of “good/fair” and “poor” to develop four Minnesota-based DSRC models. The basis for Pagosa Springs and Minnesota DSRC model effectiveness was founded on measures of goodness-of-fit that included proximity of the model(s) fitted line to the 95-percent confidence intervals of the site-specific model, Nash-Sutcliffe Efficiency values, model biases, and deviation of annual sediment loads from each model to the annual sediment loads calculated from measured data.Composite plots comparing Pagosa Springs DSRCs, Minnesota DSRCs, site-specific regression models, and measured data indicated that regionally developed DSRCs (Minnesota DSRC models) more closely approximated measured data for nearly every site. Pagosa Springs DSRC models had markedly larger exponents (slopes) when compared to the Minnesota DSRC models and the site-specific regression models, and over-represent SSC and bedload at streamflows exceeding bankfull. The Nash-Sutcliffe Efficiency values for the Minnesota DSRC model for suspended-sediment concentrations closely matched Nash-Sutcliffe Efficiency values of the site-specific regression models for 12 out of 16 sites. Nash-Sutcliffe Efficiency values associated with Minnesota DSRCs were greater than those associated with Pagosa Springs DSRCs for every site except the Whitewater River near Beaver, Minnesota site. Pagosa Springs DSRC models were less accurate than the mean of the measured data at predicting SSC values for one-half of the sites for good/fair stability sites and one-half of the sites for poor stability sites. Relative model biases were calculated and determined to be substantial (greater than 5 percent) for Pagosa Springs and Minnesota models, with Minnesota models having a lower mean model bias. For predicted annual suspended-sediment loads (SSL), the Minnesota DSRC models for good/fair and poor stream stability sites more closely approximated the annual SSLs calculated from the measured data as compared to the Pagosa Springs DSRC model.Results of data analyses indicate that DSRC models developed using data collected in Minnesota were more effective at compensating for differences in individual stream characteristics across a variety of basin sizes and flow regimes than DSRC models developed using data collected for Pagosa Springs, Colorado. Minnesota DSRC models retained a substantial portion of the unique sediment signatures for most rivers, although deviations were observed for streams with limited sediment supply and for rivers in southeastern Minnesota, which had markedly larger regression exponents. Compared to Pagosa Springs DSRC models, Minnesota DSRC models had regression slopes that more closely matched the slopes of site-specific regression models, had greater Nash-Sutcliffe Efficiency values, had lower model biases, and approximated measured annual sediment loads more closely. The results presented in this report indicate that regionally based DSRCs can be used to estimate reasonably accurate values of SSC and bedload.Practitioners are cautioned that DSRC reliability is dependent on representative measures of bankfull streamflow, SSC, and bedload. It is, therefore, important that samples of SSC and bedload, which will be used for estimating SSC and bedload at the bankfull streamflow, are collected over a range of conditions that includes the ascending and descending limbs of the event hydrograph. The use of DSRC models may have substantial limitations for certain conditions. For example, DSRC models should not be used to predict SSC and sediment loads for extreme streamflows, such as those that exceed twice the bankfull streamflow value because this constitutes conditions beyond the realm of current (2016) empirical modeling capability. Also, if relations between SSC and streamflow and between bedload and streamflow are not statistically significant, DSRC models should not be used to predict SSC or bedload, as this could result in large errors. For streams that do not violate these conditions, DSRC estimates of SSC and bedload can be used for stream restoration planning and design, and for estimating annual sediment loads for streams where little or no sediment data are available.

West Florida shelf circulation and temperature budget for the 1999 spring transition

USGS Publications Warehouse

He, Ruoying; Weisberg, Robert H.

2002-01-01

Mid-latitude continental shelves undergo a spring transition as the net surface heat flux changes from cooling to warming. Using in situ data and a numerical circulation model we investigate the circulation and temperature budget on the West Florida Continental Shelf (WFS) for the spring transition of 1999. The model is a regional adaptation of the primitive equation, Princeton Ocean Model forced by NCEP reanalysis wind and heat flux fields and by river inflows. Based on agreements between the modeled and observed fields we use the model to draw inferences on how the surface momentum and heat fluxes affect the seasonal and synoptic scale variability. We account for a strong southeastward current at mid-shelf by the baroclinic response to combined wind and buoyancy forcing, and we show how this local forcing leads to annually occurring cold and low salinity tongues. Through term-by-term analyses of the temperature budget we describe the WFS temperature evolution in spring. Heat flux largely controls the seasonal transition, whereas ocean circulation largely controls the synoptic scale variability. These two processes, however, are closely linked. Bottom topography and coastline geometry are important in generating regions of convergence and divergence. Rivers contribute to the local hydrography and are important ecologically. Along with upwelling, river inflows facilitate frontal aggregation of nutrients and the spring formation of a high concentration chlorophyll plume near the shelf break (the so-called ‘Green River’) coinciding with the cold, low salinity tongues. These features originate by local, shelf-wide forcing; the Loop Current is not an essential ingredient.

Preferential Flow Paths In A Karstified Spring Catchment: A Study Of Fault Zones As Conduits To Rapid Groundwater Flow

NASA Astrophysics Data System (ADS)

Kordilla, J.; Terrell, A. N.; Veltri, M.; Sauter, M.; Schmidt, S.

2017-12-01

In this study we model saturated and unsaturated flow in the karstified Weendespring catchment, located within the Leinetal graben in Goettingen, Germany. We employ the finite element COMSOL Multiphysics modeling software to model variably saturated flow using the Richards equation with a van Genuchten type parameterization. As part of the graben structure, the Weende spring catchment is intersected by seven fault zones along the main flow path of the 7400 m cross section of the catchment. As the Weende spring is part of the drinking water supply in Goettingen, it is particularly important to understand the vulnerability of the catchment and effect of fault zones on rapid transport of contaminants. Nitrate signals have been observed at the spring only a few days after the application of fertilizers within the catchment at a distance of approximately 2km. As the underlying layers are known to be highly impermeable, fault zones within the area are likely to create rapid flow paths to the water table and the spring. The model conceptualizes the catchment as containing three hydrogeological limestone units with varying degrees of karstification: the lower Muschelkalk limestone as a highly conductive layer, the middle Muschelkalk as an aquitard, and the upper Muschelkalk as another conductive layer. The fault zones are parameterized based on a combination of field data from quarries, remote sensing and literary data. The fault zone is modeled considering the fracture core as well as the surrounding damage zone with separate, specific hydraulic properties. The 2D conceptual model was implemented in COMSOL to study unsaturated flow at the catchment scale using van Genuchten parameters. The study demonstrates the importance of fault zones for preferential flow within the catchment and its effect on the spatial distribution of vulnerability.

Honey bees (Apis mellifera ligustica) swing abdomen to dissipate residual flying energy landing on a wall

NASA Astrophysics Data System (ADS)

Zhao, Jieliang; Huang, He; Yan, Shaoze

2017-03-01

Whether for insects or for aircrafts, landing is one of the indispensable links in the verification of airworthiness safety. The mechanisms by which insects achieve a fast and stable landing remain unclear. An intriguing example is provided by honeybees (Apis mellifera ligustica), which use the swinging motion of their abdomen to dissipate residual flying energy and to achieve a smooth, stable, and quick landing. By using a high-speed camera, we observed that touchdown is initiated by honeybees extending their front legs or antennae and then landing softly on a wall. After touchdown, they swing the rest of their bodies until all flying energy is dissipated. We suggested a simplified model with mass-spring dampers for the body of the honeybee and revealed the mechanism of flying energy transfer and dissipation in detail. Results demonstrate that body translation and abdomen swinging help honeybees dissipate residual flying energy and orchestrate smooth landings. The initial kinetic energy of flying is transformed into the kinetic energy of the abdomen's rotary movement. Then, the kinetic energy of rotary movement is converted into thermal energy during the swinging cycle. This strategy provides more insight into the mechanism of insect flying, which further inspires better design on aerial vehicle with better landing performance.

Obliquity evolution of the minor satellites of Pluto and Charon

NASA Astrophysics Data System (ADS)

Quillen, Alice C.; Nichols-Fleming, Fiona; Chen, Yuan-Yuan; Noyelles, Benoît

2017-09-01

New Horizons mission observations show that the small satellites Styx, Nix, Kerberos and Hydra, of the Pluto-Charon system, have not tidally spun-down to near synchronous spin states and have high obliquities with respect to their orbit about the Pluto-Charon binary (Weaver, 2016). We use a damped mass-spring model within an N-body simulation to study spin and obliquity evolution for single spinning non-round bodies in circumbinary orbit. Simulations with tidal dissipation alone do not show strong obliquity variations from tidally induced spin-orbit resonance crossing and this we attribute to the high satellite spin rates and low orbital eccentricities. However, a tidally evolving Styx exhibits intermittent obliquity variations and episodes of tumbling. During a previous epoch where Charon migrated away from Pluto, the minor satellites could have been trapped in orbital mean motion inclination resonances. An outward migrating Charon induces large variations in Nix and Styx's obliquities. The cause is a commensurability between the mean motion resonance frequency and the spin precession rate of the spinning body. As the minor satellites are near mean motion resonances, this mechanism could have lifted the obliquities of all four minor satellites. The high obliquities need not be primordial if the minor satellites were at one time captured into mean motion resonances.

Carbonate ion-enriched hot spring water promotes skin wound healing in nude rats.

PubMed

Liang, Jingyan; Kang, Dedong; Wang, Yingge; Yu, Ying; Fan, Jianglin; Takashi, En

2015-01-01

Hot spring or hot spa bathing (Onsen) is a traditional therapy for the treatment of certain ailments. There is a common belief that hot spring bathing has therapeutic effects for wound healing, yet the underlying molecular mechanisms remain unclear. To examine this hypothesis, we investigated the effects of Nagano hot spring water (rich in carbonate ion, 42°C) on the healing process of the skin using a nude rat skin wound model. We found that hot spring bathing led to an enhanced healing speed compared to both the unbathed and hot-water (42°C) control groups. Histologically, the hot spring water group showed increased vessel density and reduced inflammatory cells in the granulation tissue of the wound area. Real-time RT-PCR analysis along with zymography revealed that the wound area of the hot spring water group exhibited a higher expression of matrix metalloproteinases-2 and -9 compared to the two other control groups. Furthermore, we found that the enhanced wound healing process induced by the carbonate ion-enriched hot spring water was mediated by thermal insulation and moisture maintenance. Our results provide the evidence that carbonate ion-enriched hot spring water is beneficial for the treatment of skin wounds.

Effect of Spring-in Deviation on Fatigue Life of Composite Elevator Assembly

NASA Astrophysics Data System (ADS)

Wang, Hua

2017-12-01

The spring-in deviation results in the extra stresses around the joints of the composite C-beam and metallic parts when they are assembled together. These extra stresses affect the composite elevator's fatigue life, which should be explored with the fatigue experimentation. The paper presents the experimental investigation on the effect of spring-in deviation on the fatigue life of the composite elevator assembly. The investigation seeks to build the relationship between the spring-in and the fatigue life in order to determine the spring-in threshold during the course of assembling. The phenomenological model of the composite C-beam is constructed to predict the stresses around the joints. Based on the predicted spring-in induced stresses around the joints, pre-stresses are precisely added to the fatigue specimen when conducting the fatigue experiment. At last, the relationship curve of the spring-in on the composite C-beam's fatigue life is obtained from the experimental data. Giving the fatigue life accepting limits, the maximum accepting spring-in deviation during the course of assembling could be obtained from the relationship curve. The reported work will enhance the understanding of assembling the composites with spring-in deviation in the civil aircraft industry.

Characterizing hydrochemical properties of springs in Taiwan based on their geological origins.

PubMed

Jang, Cheng-Shin; Chen, Jui-Sheng; Lin, Yun-Bin; Liu, Chen-Wuing

2012-01-01

This study was performed to characterize hydrochemical properties of springs based on their geological origins in Taiwan. Stepwise discriminant analysis (DA) was used to establish a linear classification model of springs using hydrochemical parameters. Two hydrochemical datasets-ion concentrations and relative proportions of equivalents per liter of major ions-were included to perform prediction of the geological origins of springs. Analyzed results reveal that DA using relative proportions of equivalents per liter of major ions yields a 95.6% right assignation, which is superior to DA using ion concentrations. This result indicates that relative proportions of equivalents of major hydrochemical parameters in spring water are more highly associated with the geological origins than ion concentrations do. Low percentages of Na(+) equivalents are common properties of springs emerging from acid-sulfate and neutral-sulfate igneous rock. Springs emerging from metamorphic rock show low percentages of Cl( - ) equivalents and high percentages of HCO[Formula: see text] equivalents, and springs emerging from sedimentary rock exhibit high Cl( - )/SO(2-)(4) ratios.

3D Model of the Neal Hot Springs Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

The Neal Hot Springs geothermal system lies in a left-step in a north-striking, west-dipping normal fault system, consisting of the Neal Fault to the south and the Sugarloaf Butte Fault to the north (Edwards, 2013). The Neal Hot Springs 3D geologic model consists of 104 faults and 13 stratigraphic units. The stratigraphy is sub-horizontal to dipping <10 degrees and there is no predominant dip-direction. Geothermal production is exclusively from the Neal Fault south of, and within the step-over, while geothermal injection is into both the Neal Fault to the south of the step-over and faults within the step-over.

Repeatability of Mice Consumption Discrimination of Wheat (Triticum aestivum L.) Varieties across Field Experiments and Mouse Cohorts.

PubMed

Kiszonas, Alecia M; Fuerst, E Patrick; Morris, Craig F

2015-07-01

Whole grain wheat (Triticum aestivum L.) foods can provide critical nutrients for health and nutrition in the human diet. Potential flavor differences among varieties can be examined using consumption discrimination of the house mouse (Mus musculus L.) as a model system. This study examines consistency and repeatability of the mouse model and potentially, wheat grain flavor. A single elimination tournament design was used to measure relative consumption preference for hard red spring and hard white spring varieties across all 3 experiments in combination with 2 mouse cohorts. Fifteen replicate mice were used in 24-h trials to examine differences in preference among paired wheat varieties until an overall "winner" was established as the most highly preferred variety of wheat. In all 3 experiment-cohort combinations, the same varieties were preferred as the "winner" of both the hard red spring and hard white spring wheat varieties, Hollis and BR 7030, respectively. Despite the consistent preference for these varieties across experiments, the degree (magnitude) to which the mice preferred these varieties varied across experiments. For the hard white spring wheat varieties, the small number of varieties and confounding effects of experiment and cohort limited our ability to accurately gauge repeatability. Conversely, for the hard red spring wheat varieties, consumption preferences were consistent across experiments and mice cohorts. The single-elimination tournament model was effective in providing repeatable results in an effort to more fully understand the mouse model system and possible flavor differences among wheat varieties. The mouse model system used here is effective in identifying wheat varieties that may be more or less desirable to humans in whole wheat foods. The system identifies consistent differences across different mouse cohorts and crop years. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Morphological and metabolic adjustments in the small intestine to energy demands of growth, storage, and fasting in the first annual cycle of a hibernating lizard (Tupinambis merianae).

PubMed

do Nascimento, Lucas Francisco R; da Silveira, Lilian Cristina; Nisembaum, Laura Gabriela; Colquhoun, Alison; Abe, Agusto S; Mandarim-de-Lacerda, Carlos Alberto; de Souza, Silvia Cristina R

2016-05-01

Seasonal plasticity in the small intestine of neonatal tegu lizards was investigated using morphometry and analysis of enzymes involved in supplying energy to the intestinal tissue. In the autumn, the intestinal mass (Mi) was 1.0% of body mass and the scaling exponent b=0.92 indicated that Mi was larger in smaller neonates. During arousal from dormancy Mi was 23% smaller; later in spring, Mi increased 60% in relation to the autumn and the exponent b=0.14 indicated that the recovery was disproportionate in smaller tegus. During the autumn, the intestinal villi were greatly elongated; by midwinter, the Hv, SvEp, and VvEp were smaller than during the autumn (59%, 54%, 29%) and were restored to autumn levels during spring. In the active tegus, the maximum activity (Vmax) of enzymes indicated that the enterocytes can obtain energy from different sources, and possess gluconeogenic capacity. During winter, the Vmax of CS, HOAD, GDH, PEPCK was 40-50% lower in relation to the autumn and spring, while the Vmax of HK, PK, LDH, AST was unchanged. The hypoglycemia and the mucosal atrophy/ischemia during winter would prevent the enterocytes from using glucose, whereas they could slowly oxidize fatty acids released from body stores and amino acids from the tissue proteolysis to satisfy their needs of energy. Contrastingly, starvation during spring caused severe mass loss (50%); the tissue protein and the VvEp and VvLP did not change while the thickness of the muscular layer increased 51%, which suggested different effects along the length of the organ. In addition, the Vmax of the glycolytic enzymes was lower, indicating that a regulatory mechanism would spare blood glucose for vital organs during unanticipated food restriction. Copyright © 2016 Elsevier Inc. All rights reserved.

SPRING: an RCT study of probiotics in the prevention of gestational diabetes mellitus in overweight and obese women

PubMed Central

2013-01-01

Background Obesity is increasing in the child-bearing population as are the rates of gestational diabetes. Gestational diabetes is associated with higher rates of Cesarean Section for the mother and increased risks of macrosomia, higher body fat mass, respiratory distress and hypoglycemia for the infant. Prevention of gestational diabetes through life style intervention has proven to be difficult. A Finnish study showed that ingestion of specific probiotics altered the composition of the gut microbiome and thereby metabolism from early gestation and decreased rates of gestational diabetes in normal weight women. In SPRING (the Study of Probiotics IN the prevention of Gestational diabetes), the effectiveness of probiotics ingestion for the prevention of gestational diabetes will be assessed in overweight and obese women. Methods/design SPRING is a multi-center, prospective, double-blind randomized controlled trial run at two tertiary maternity hospitals in Brisbane, Australia. Five hundred and forty (540) women with a BMI > 25.0 kg/m2 will be recruited over 2 years and receive either probiotics or placebo capsules from 16 weeks gestation until delivery. The probiotics capsules contain > 1x109 cfu each of Lactobacillus rhamnosus GG and Bifidobacterium lactis BB-12 per capsule. The primary outcome is diagnosis of gestational diabetes at 28 weeks gestation. Secondary outcomes include rates of other pregnancy complications, gestational weight gain, mode of delivery, change in gut microbiome, preterm birth, macrosomia, and infant body composition. The trial has 80% power at a 5% 2-sided significance level to detect a >50% change in the rates of gestational diabetes in this high-risk group of pregnant women. Discussion SPRING will show if probiotics can be used as an easily implementable method of preventing gestational diabetes in the high-risk group of overweight and obese pregnant women. PMID:23442391

Tracking from the tropics reveals behaviour of juvenile songbirds on their first spring migration.

PubMed

McKinnon, Emily A; Fraser, Kevin C; Stanley, Calandra Q; Stutchbury, Bridget J M

2014-01-01

Juvenile songbirds on spring migration travel from tropical wintering sites to temperate breeding destinations thousands of kilometres away with no prior experience to guide them. We provide a first glimpse at the migration timing, routes, and stopover behaviour of juvenile wood thrushes (Hylocichla mustelina) on their inaugural spring migration by using miniaturized archival geolocators to track them from Central America to the U.S. and Canada. We found significant differences between the timing of juvenile migration and that of more experienced adults: juveniles not only departed later from tropical wintering sites relative to adults, they also became progressively later as they moved northward. The increasing delay was driven by more frequent short stops by juveniles along their migration route, particularly in the U.S. as they got closer to breeding sites. Surprisingly, juveniles were just as likely as adults to cross the Gulf of Mexico, an open-water crossing of 800-1000 km, and migration route at the Gulf was not significantly different for juveniles relative to adults. To determine if the later departure of juveniles was related to poor body condition in winter relative to adults, we examined percent lean body mass, fat scores, and pectoral muscle scores of juvenile versus adult birds at a wintering site in Belize. We found no age-related differences in body condition. Later migration timing of juveniles relative to adults could be an adaptive strategy (as opposed to condition-dependent) to avoid the high costs of fast migration and competition for breeding territories with experienced and larger adults. We did find significant differences in wing size between adults and juveniles, which could contribute to lower flight efficiency of juveniles and thus slower overall migration speed. We provide the first step toward understanding the "black box" of juvenile songbird migration by documenting their migration timing and en route performance.

Tracking from the Tropics Reveals Behaviour of Juvenile Songbirds on Their First Spring Migration

PubMed Central

McKinnon, Emily A.; Fraser, Kevin C.; Stanley, Calandra Q.; Stutchbury, Bridget J. M.

2014-01-01

Juvenile songbirds on spring migration travel from tropical wintering sites to temperate breeding destinations thousands of kilometres away with no prior experience to guide them. We provide a first glimpse at the migration timing, routes, and stopover behaviour of juvenile wood thrushes (Hylocichla mustelina) on their inaugural spring migration by using miniaturized archival geolocators to track them from Central America to the U.S. and Canada. We found significant differences between the timing of juvenile migration and that of more experienced adults: juveniles not only departed later from tropical wintering sites relative to adults, they also became progressively later as they moved northward. The increasing delay was driven by more frequent short stops by juveniles along their migration route, particularly in the U.S. as they got closer to breeding sites. Surprisingly, juveniles were just as likely as adults to cross the Gulf of Mexico, an open-water crossing of 800–1000 km, and migration route at the Gulf was not significantly different for juveniles relative to adults. To determine if the later departure of juveniles was related to poor body condition in winter relative to adults, we examined percent lean body mass, fat scores, and pectoral muscle scores of juvenile versus adult birds at a wintering site in Belize. We found no age-related differences in body condition. Later migration timing of juveniles relative to adults could be an adaptive strategy (as opposed to condition-dependent) to avoid the high costs of fast migration and competition for breeding territories with experienced and larger adults. We did find significant differences in wing size between adults and juveniles, which could contribute to lower flight efficiency of juveniles and thus slower overall migration speed. We provide the first step toward understanding the “black box” of juvenile songbird migration by documenting their migration timing and en route performance. PMID:25141193

Effect of body condition and season on yield and quality of in vitro produced bovine embryos.

PubMed

Chrenek, Peter; Kubovičová, Elena; Olexíková, Lucia; Makarevich, Alexander V; Toporcerová, Silvia; Ostró, Alexander

2015-12-01

The aim of our study was to examine the effects of cow's body condition score (BCS; scale 1-5) and season on the quality of bovine in vitro produced embryos. The proportion of good quality oocytes (Q1 and Q2) was higher (P < 0.05) in the BCS 2 (57.60%) and BCS 3 (60.90%) groups compared with the BCS 1 (43.60%) group. There were no statistical differences in embryo cleavage and blastocyst rate among the BCS groups. The highest total cell number (TCN, DAPI stain) of blastocysts (P < 0.05), recorded in BCS 1 (122.27 ± 6.90) in comparison with BCS 2 (101.8 ± 3.60) or BCS 3 (105.44 ± 3.70) groups, was related to higher dead cell (DCI, TUNEL) index in this group (7.07%) when compared with BCS 2 (6.54%) or BCS 3 (6.06%), respectively. The yield of good quality oocytes during spring was lower (P < 0.05) compared with the summer season. There were significant differences (P < 0.05) in maturation and cleavage rates between autumn and summer (73.42%, 76.2% vs. 85.0%, 41.8%, respectively). The highest (P < 0.01) blastocyst rate was noted during spring and summer months. Significant difference (P < 0.05) in the TCN among spring (99.38 ± 3.90), autumn (110.1 ± 4.58) or summer (108.96 ± 3.52) was observed. The highest proportion of embryos with the best (grade I) actin cytoskeleton (phalloidin-TRITC) quality was noted during the summer months. Our results indicate that body condition affects the initial quality of oocytes, but does not affect embryo cleavage, blastocyst rate and actin quality. This finding may suggest that development in vitro can mask the influence of BCS. The season affects yield and quality of blastocysts in the way that the autumn period is more favorable for embryo development.

Spring fasting behavior in a marine apex predator provides an index of ecosystem productivity

USGS Publications Warehouse

Rode, Karyn D.; Wilson, Ryan R.; Douglas, David C.; Muhlenbruch, Vanessa L; Atwood, Todd C.; Regehr, Eric V.; Richardson, Evan; Pilfold, Nicholas; Derocher, Andrew E.; Durner, George M.; Stirling, Ian; Amstrup, Steven C.; St Martin, Michelle; Pagano, Anthony M.; Simac, Kristin

2018-01-01

The effects of declining Arctic sea ice on local ecosystem productivity are not well understood but have been shown to vary inter-specifically, spatially, and temporally. Because marine mammals occupy upper trophic levels in Arctic food webs, they may be useful indicators for understanding variation in ecosystem productivity. Polar bears (Ursus maritimus) are apex predators that primarily consume benthic and pelagic-feeding ice-associated seals. As such, their productivity integrates sea ice conditions and the ecosystem supporting them. Declining sea ice availability has been linked to negative population effects for polar bears but does not fully explain observed population changes. We examined relationships between spring foraging success of polar bears and sea ice conditions, prey productivity, and general patterns of ecosystem productivity in the Beaufort and Chukchi Seas (CSs). Fasting status (≥7 days) was estimated using serum urea and creatinine levels of 1,448 samples collected from 1,177 adult and subadult bears across three subpopulations. Fasting increased in the Beaufort Sea between 1983–1999 and 2000–2016 and was related to an index of ringed seal body condition. This change was concurrent with declines in body condition of polar bears and observed changes in the diet, condition and/or reproduction of four other vertebrate consumers within the food chain. In contrast, fasting declined in CS polar bears between periods and was less common than in the two Beaufort Sea subpopulations consistent with studies demonstrating higher primary productivity and maintenance or improved body condition in polar bears, ringed seals, and bearded seals despite recent sea ice loss in this region. Consistency between regional and temporal variation in spring polar bear fasting and food web productivity suggests that polar bears may be a useful indicator species. Furthermore, our results suggest that spatial and temporal ecological variation is important in affecting upper trophic-level productivity in these marine ecosystems.

Spring fasting behavior in a marine apex predator provides an index of ecosystem productivity.

PubMed

Rode, Karyn D; Wilson, Ryan R; Douglas, David C; Muhlenbruch, Vanessa; Atwood, Todd C; Regehr, Eric V; Richardson, Evan S; Pilfold, Nicholas W; Derocher, Andrew E; Durner, George M; Stirling, Ian; Amstrup, Steven C; St Martin, Michelle; Pagano, Anthony M; Simac, Kristin

2018-01-01

The effects of declining Arctic sea ice on local ecosystem productivity are not well understood but have been shown to vary inter-specifically, spatially, and temporally. Because marine mammals occupy upper trophic levels in Arctic food webs, they may be useful indicators for understanding variation in ecosystem productivity. Polar bears (Ursus maritimus) are apex predators that primarily consume benthic and pelagic-feeding ice-associated seals. As such, their productivity integrates sea ice conditions and the ecosystem supporting them. Declining sea ice availability has been linked to negative population effects for polar bears but does not fully explain observed population changes. We examined relationships between spring foraging success of polar bears and sea ice conditions, prey productivity, and general patterns of ecosystem productivity in the Beaufort and Chukchi Seas (CSs). Fasting status (≥7 days) was estimated using serum urea and creatinine levels of 1,448 samples collected from 1,177 adult and subadult bears across three subpopulations. Fasting increased in the Beaufort Sea between 1983-1999 and 2000-2016 and was related to an index of ringed seal body condition. This change was concurrent with declines in body condition of polar bears and observed changes in the diet, condition and/or reproduction of four other vertebrate consumers within the food chain. In contrast, fasting declined in CS polar bears between periods and was less common than in the two Beaufort Sea subpopulations consistent with studies demonstrating higher primary productivity and maintenance or improved body condition in polar bears, ringed seals, and bearded seals despite recent sea ice loss in this region. Consistency between regional and temporal variation in spring polar bear fasting and food web productivity suggests that polar bears may be a useful indicator species. Furthermore, our results suggest that spatial and temporal ecological variation is important in affecting upper trophic-level productivity in these marine ecosystems. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

The influence of genetic selection and feed system on the reproductive performance of spring-calving dairy cows within future pasture-based production systems.

PubMed

Coleman, J; Pierce, K M; Berry, D P; Brennan, A; Horan, B

2009-10-01

Three genetic groups of Holstein-Friesian dairy cows were established from within the Moorepark (Teagasc, Ireland) dairy research herd: LowNA, indicative of the Irish national average-genetic-merit North American Holstein-Friesian; HighNA, high-genetic-merit North American Holstein-Friesian; HighNZ, high-genetic-merit New Zealand Holstein-Friesian. Genetic merit in this study was based on the Irish total merit index, the Economic Breeding Index. Animals from within each genetic group were randomly allocated to 1 of 2 possible post-European Union-milk-quota pasture-based feeding systems (FS): 1) The Moorepark (MP) pasture system (2.64 cows/ha and 500 kg of concentrate supplement per cow per lactation) and 2) a high output per hectare (HC) pasture system (2.85 cows/ha and 1,200 kg of concentrate supplement per cow per lactation). A total of 126, 128, and 140 spring-calving dairy cows were used during the years 2006, 2007, and 2008, respectively. Each group had an individual farmlet of 17 paddocks, and all groups were managed similarly throughout the study. The effects of genetic group, FS, and the interaction between genetic group and FS on reproductive performance, body weight, body condition score, and blood metabolite concentrations were studied using mixed models with factorial arrangements of genetic groups and FS. Odds ratios were used in the analysis of binary fertility traits, and survival analysis was used in the analysis of survival after first calving. When treatment means were compared, the HighNA and HighNZ genotypes (with greater genetic merit for fertility performance) had greater first-service pregnancy rates and had a greater proportion of cows pregnant after 42 d of the breeding season than the LowNA group. Both HighNA and HighNZ genotypes were submitted for artificial insemination earlier in the breeding season and had greater survival than the LowNA genotype. There was no significant FS or genotype by FS interactions for any of the reproductive, blood metabolite, body weight, or body condition score measures. The results demonstrate that increased genetic merit for fertility traits resulted in improved reproductive performance and that the poor reproductive capacity of inferior-genetic-merit animals for fertility was not improved through concentrate supplementation at pasture.

Weakening temperature control on the interannual variations of spring carbon uptake across northern lands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piao, Shilong; Liu, Zhuo; Wang, Tao

2017-04-24

Ongoing spring warming allows the growing season to begin earlier, enhancing carbon uptake in northern ecosystems. We use 34 years of atmospheric CO 2 concentration measurements at Barrow, Alaska (BRW, 71° N) to show that the interannual relationship between spring temperature and carbon uptake has recently shifted. Here, we use two indicators: the spring zero-crossing date of atmospheric CO 2 (SZC) and the magnitude of CO 2 drawdown between May and June (SCC). The previously reported strong correlation between SZC, SCC and spring land temperature (ST) was found in the first 17 years of measurements, but disappeared in the lastmore » 17 years. As a result, the sensitivity of both SZC and SCC to warming decreased. Simulations with an atmospheric transport model coupled to a terrestrial ecosystem model suggest that the weakened interannual correlation of SZC and SCC with ST in the last 17 years is attributable to the declining temperature response of spring net primary productivity (NPP) rather than to changes in heterotrophic respiration or in atmospheric transport patterns. Reduced chilling during dormancy and emerging light limitation are possible mechanisms that may have contributed to the loss of NPP response to ST. These results thus challenge the ‘warmer spring–bigger sink’ mechanism.« less

Zero Power Non-Contact Suspension System with Permanent Magnet Motion Feedback

NASA Astrophysics Data System (ADS)

Sun, Feng; Oka, Koichi

This paper proposes a zero power control method for a permanent magnetic suspension system consisting mainly of a permanent magnet, an actuator, sensors, a suspended iron ball and a spring. A system using this zero power control method will consume quasi-zero power when the levitated object is suspended in an equilibrium state. To realize zero power control, a spring is installed in the magnetic suspension device to counterbalance the gravitational force on the actuator in the equilibrium position. In addition, an integral feedback loop in the controller affords zero actuator current when the device is in a balanced state. In this study, a model was set up for feasibility analysis, a prototype was manufactured for experimental confirmation, numerical simulations of zero power control with nonlinear attractive force were carried out based on the model, and experiments were completed to confirm the practicality of the prototype. The simulations and experiments were performed under varied conditions, such as without springs and without zero power control, with springs and without zero power control, with springs and with zero power control, using different springs and integral feedback gains. Some results are shown and analyzed in this paper. All results indicate that this zero power control method is feasible and effective for use in this suspension system with a permanent magnet motion feedback loop.

Factors driving mercury variability in the Arctic atmosphere and ocean over the past 30 years

NASA Astrophysics Data System (ADS)

Fisher, Jenny A.; Jacob, Daniel J.; Soerensen, Anne L.; Amos, Helen M.; Corbitt, Elizabeth S.; Streets, David G.; Wang, Qiaoqiao; Yantosca, Robert M.; Sunderland, Elsie M.

2013-12-01

observations at Arctic sites (Alert and Zeppelin) show large interannual variability (IAV) in atmospheric mercury (Hg), implying a strong sensitivity of Hg to environmental factors and potentially to climate change. We use the GEOS-Chem global biogeochemical Hg model to interpret these observations and identify the principal drivers of spring and summer IAV in the Arctic atmosphere and surface ocean from 1979-2008. The model has moderate skill in simulating the observed atmospheric IAV at the two sites (r 0.4) and successfully reproduces a long-term shift at Alert in the timing of the spring minimum from May to April (r = 0.7). Principal component analysis indicates that much of the IAV in the model can be explained by a single climate mode with high temperatures, low sea ice fraction, low cloudiness, and shallow boundary layer. This mode drives decreased bromine-driven deposition in spring and increased ocean evasion in summer. In the Arctic surface ocean, we find that the IAV for modeled total Hg is dominated by the meltwater flux of Hg previously deposited to sea ice, which is largest in years with high solar radiation (clear skies) and cold spring air temperature. Climate change in the Arctic is projected to result in increased cloudiness and strong warming in spring, which may thus lead to decreased Hg inputs to the Arctic Ocean. The effect of climate change on Hg discharges from Arctic rivers remains a major source of uncertainty.

Areas with Surface Thermal Anomalies as Detected by ASTER and LANDSAT Data in Southwest Steamboat Springs, Garfield County, Colorado

DOE Data Explorer

Khalid Hussein

2012-02-01

This map shows areas of anomalous surface temperature around south Steamboat Springs as identified from ASTER and LANDSAT thermal data and spatial based insolation model. The temperature for the ASTER data was calculated using the Emissivity Normalization Algorithm that separate temperature from emissivity. The incoming solar radiation was calculated using spatial based insolation model developed by Fu and Rich (1999). Then the temperature due to solar radiation was calculated using emissivity derived from ASTER data. The residual temperature, i.e. temperature due to solar radiation subtracted from ASTER temperature was used to identify thermally anomalous areas. Areas having anomalous temperature in the ASTER data are shown in blue diagonal hatch, while areas having anomalous temperature in the LANDSAT data are shown in magenta on the map. Thermal springs and areas with favorable geochemistry are also shown. Springs or wells having non-favorable geochemistry are shown as blue dots.

Spring feeding on ungulate carcasses by grizzly bears in Yellowstone National Park

USGS Publications Warehouse

Green, Gerald I.; Mattson, D.J.; Peek, J.M.

1997-01-01

We studied the spring use of ungulate carcasses by grizzly bears (Ursus arctos horribilis) on ungulate winter ranges in Yellowstone National Park. We observed carcasses and bear tracks on survey routes that were travelled biweekly during spring of 1985-90 in the Firehole-Gibbon winter range and spring of 1987-90 in the Northern winter range. The probability that grizzly bears used a carcass was positively related to elevation and was lower within 400 m of a road, or within 5 km of a major recreational development compared to elsewhere. Carcass use peaked in April, coincident with peak ungulate deaths. Grizzly bears also were more likely to use carcasses in the Firehole-Gibbon compared to Northern Range study area. We attributed the effects of study area and elevation to the fact that grizzly bears den and are first active in the spring at high elevations and to differences in densities of competing scavengers. Probability of grizzly bear use was strongly related to body mass of carcasses on the Northern Range where densities of coyotes (Canis latrans) and black bears (U. americanus) appeared to be much higher than in the Firehole-Gibbon study area. We suggest that additional restrictions on human activity in ungulate winter ranges or movement of carcasses to remote areas could increase grizzly bear use of carrion. Fewer competing scavengers and greater numbers of adult ungulates vulnerable to winter mortality could have the same effect.

Novel In-Shoe Exoskeleton for Offloading of Forefoot Pressure for Individuals With Diabetic Foot Pathology.

PubMed

Roser, Mark C; Canavan, Paul K; Najafi, Bijan; Cooper Watchman, Marcy; Vaishnav, Kairavi; Armstrong, David G

2017-09-01

Infected diabetic foot ulcers are the leading cause of lower limb amputation. This study evaluated the ability of in-shoe exoskeletons to redirect forces outside of body and through an exoskeleton as an effective means of offloading plantar pressure, the major contributing factor of ulceration. We compared pressure in the forefoot and hind-foot of participants (n = 5) shod with novel exoskeleton footwear. Plantar pressure readings were taken during a 6-m walk at participant's self-selected speed, and five strides were averaged. Results were taken with Achilles exotendon springs disengaged as a baseline, followed by measurements taken with the springs engaged. When springs were engaged, all participants demonstrated a decrease in forefoot pressure, averaging a 22% reduction ( P < .050). Patient feedback was universally positive, preferring the exotendon springs to be engaged and active. Offloading is standard of care for reducing harmful plantar pressure, which may lead to foot ulcers. However, current offloading modalities are limited and have issues. This proof-of-concept study proposed a novel offloading approach based on an exoskeleton solution. Results suggest that when the novel exoskeletons were deployed in footwear and exotendon springs engaged, force was successfully transferred from the lower leg through the exoskeleton-enabled shoe to ground, reducing load on the forefoot. The results need to be confirmed in a larger sample. Another study is warranted to examine the effectiveness of this offloading to prevent diabetic foot ulcer, while minimizing gait alteration in daily physical activities.

Influence of season of birth on growth and reproductive development of Brahman bulls.

PubMed

Tatman, Shawn R; Neuendorff, Don A; Wilson, Timothy W; Randel, Ronald D

2004-07-01

Seasonal effects on reproduction are more dramatic in Bos indicus than Bos taurus cattle. This experiment evaluated reproductive development of fall- (n=7) versus spring- (n = 10) born Brahman bulls to determine if season of birth affects reproductive development. Measurements of growth and reproductive development began after weaning and continued at bi-weekly intervals until each bull reached sexual maturity. Different stages of sexual development were classified according to characteristics of the ejaculate and included first sperm in the ejaculate, puberty (> 50 x 10(6) sperm/ejaculate), and sexual maturity (two ejaculates with > 500 = 10(6) sperm/ejaculate). Average daily increases in all measured traits were similar in fall- and spring-born bulls and there were no differences in age, body weight, scrotal circumference, or paired testis volume between groups at first sperm or puberty. However, fall-born bulls were older (P < 0.05) than spring-born bulls at sexual maturity (553 days versus 481 days, respectively) as the interval between puberty and sexual maturity was longer (P < 0.05) in fall- than in spring-born bulls (82 days versus 54 days, respectively). The prolonged interval between puberty and sexual maturity in fall-born calves coincided with a short photoperiod (winter) whereas the short interval between puberty and sexual maturity in spring-born calves coincided with a long photoperiod (summer). In conclusion, season of birth affected sexual development; photoperiod might be involved in regulating testicular function immediately after puberty in Brahman bulls.

Climate model assessment of changes in winter-spring streamflow timing over North America

USGS Publications Warehouse

Kam, Jonghun; Knutson, Thomas R.; Milly, Paul C. D.

2018-01-01

Over regions where snow-melt runoff substantially contributes to winter-spring streamflows, warming can accelerate snow melt and reduce dry-season streamflows. However, conclusive detection of changes and attribution to anthropogenic forcing is hindered by brevity of observational records, model uncertainty, and uncertainty concerning internal variability. In this study, a detection/attribution of changes in mid-latitude North American winter-spring streamflow timing is examined using nine global climate models under multiple forcing scenarios. In this study, robustness across models, start/end dates for trends, and assumptions about internal variability is evaluated. Marginal evidence for an emerging detectable anthropogenic influence (according to four or five of nine models) is found in the north-central U.S., where winter-spring streamflows have been coming earlier. Weaker indications of detectable anthropogenic influence (three of nine models) are found in the mountainous western U.S./southwestern Canada and in extreme northeastern U.S./Canadian Maritimes. In the former region, a recent shift toward later streamflows has rendered the full-record trend toward earlier streamflows only marginally significant, with possible implications for previously published climate change detection findings for streamflow timing in this region. In the latter region, no forced model shows as large a shift toward earlier streamflow timing as the detectable observed shift. In other (including warm, snow-free) regions, observed trends are typically not detectable, although in the U.S. central plains we find detectable delays in streamflow, which are inconsistent with forced model experiments.

Estimation of evapotranspiration in the Rainbow Springs and Silver Springs basins in North-Central Florida

USGS Publications Warehouse

Knowles, Leel

1996-01-01

Estimates of evapotranspiration (ET) for the Rainbow and Silver Springs ground-water basins in north-central Florida were determined using a regional water-~budget approach and compared to estimates computed using a modified Priestley-Taylor (PT) model calibrated with eddy-correlation data. Eddy-correlation measurements of latent 0~E) and sensible (H) heat flux were made monthly for a few days at a time, and the PT model was used to estimate 3,E between times of measurement during the 1994 water year. A water-budget analysis for the two-basin area indicated that over a 30-year period (196594) annual rainfall was 51.7 inches. Of the annual rainfall, ET accounted for about 37.9 inches; springflow accounted for 13.1 inches; and the remaining 0.7 inch was accounted for by stream-flow, by ground-water withdrawals from the Floridan aquifer system, and by net change in storage. For the same 30-year period, the annual estimate of ET for the Silver Springs basin was 37.6 inches and was 38.5 inches for the Rainbow Springs basin. Wet- and dry-season estimates of ET for each basin averaged between nearly 19 inches and 20 inches, indicating that like rainfall, ET rates during the 4-month wet season were about twice the ET rates during the 8-month dry season. Wet-season estimates of ET for the Rainbow Springs and Silver Springs basins decreased 2.7 inches, and 3.4 inches, respectively, over the 30-year period; whereas, dry-season estimates for the basins decreased about 0.4 inch and1.0 inch, respectively, over the 30-year period. This decrease probably is related to the general decrease in annual rainfall and reduction in net radiation over the basins during the 30-year period. ET rates computed using the modified PT model were compared to rates computed from the water budget for the 1994 water year. Annual ET, computed using the PT model, was 32.0 inches, nearly equal to the ET water-budget estimate of 31.7 inches computed for the Rainbow Springs and Silver Springs basins. Modeled ET rates for 1994 ranged from 14.4 inches per year in January to 51.6 inches per year in May. Water-budget ET rates for 1994 ranged from 12.0 inches per year in March to 61.2 inches per year in July. Potential evapotranspiration rates for 1994 averaged 46.8 inches per year and ranged from 21.6 inches per year in January to 74.4 inches per year in May. Lake evaporation rates averaged 47.1 inches per year and ranged from 18.0 inches per year in January to 72.0 inches per year in May 1994.

Seasonal shifts in shelter and microhabitat use of drymarchon couperi (eastern indigo snake) in Georgia

USGS Publications Warehouse

Hyslop, N.L.; Cooper, R.J.; Meyers, J.M.

2009-01-01

Drymarchon couperi (Eastern Indigo Snake), a threatened species of the southeastern Coastal Plain of the United States, has experienced population declines because of extensive habitat loss and degradation across its range. In Georgia and northern Florida, the species is associated with longleaf pine habitats that support Gopherus polyphemus (Gopher Tortoise) populations, the burrows of which D. couperi uses for shelter. The extent that D. couperi uses these burrows, in addition to the use of other underground shelters and the microhabitat features associated with these structures is largely unknown. From 2003 through 2004, we conducted a radiotelemetry study of D. couperi (n = 32) to examine use of shelters and microhabitat in Georgia. We used repeated measures regression on a candidate set of models created from a priori hypotheses using principal component scores, derived from analysis of microhabitat data to examine microhabitat use at underground shelters. Proportion of locations recorded underground did not differ seasonally or between sexes. In winter, we recorded >0.90 of underground locations at tortoise burrows. Use of these burrows was less pronounced in spring for males. Females used abandoned tortoise burrows more frequently than males year-round and used them on approximately 0.60 of their underground locations during spring. Microhabitat use at underground shelters was most influenced by season compared to sex, site, or body size. Females in spring and summer used more open microhabitat compared to males, potentially in response to gestation. Our results suggest that the availability of suitable underground shelters, especially G. polyphemus burrows, may be a limiting factor in the northern range of D. couperi, with important implications for its conservation. ?? 2009 by the American Society of Ichthyologists and Herpetologists.

Delineating saturated conduit patterns and dimensions in the upper Floridan aquifer through numerical groundwater flow modeling (Invited)

NASA Astrophysics Data System (ADS)

Kincaid, T. R.; Meyer, B. A.

2009-12-01

In groundwater flow modeling, aquifer permeability is typically defined through model calibration. Since the pattern and size of conduits are part of a karstic permeability framework, those parameters should be constrainable through the same process given a sufficient density of measured conditions. H2H Associates has completed a dual-permeability steady-state model of groundwater flow through the western Santa Fe River Basin, Florida from which a 380.9 km network of saturated conduits was delineated through model calibration to heads and spring discharges. Two calibration datasets were compiled describing average high-water and average low-water conditions based on heads at 145 wells and discharge from 18 springs for the high-water scenario and heads at 188 wells and discharge from 9 springs for the low-water scenario. An initial conduit network was defined by assigning paths along mapped conduits and inferring paths along potentiometric troughs between springs and swallets that had been connected by groundwater tracing. These initial conduit assignments accounted for only 13.75 and 34.1 km of the final conduit network respectively. The model was setup using FEFLOW™ where conduits were described as discrete features embedded in a porous matrix. Flow in the conduits was described by the Manning-Strickler equation where variables for conduit area and roughness were used to adjust the volume and velocity of spring flows. Matrix flow was described by Darcy’s law where hydraulic conductivity variations were limited to three geologically defined internally homogeneous zones that ranged from ~2E-6 m/s to ~4E-3 m/s. Recharge for both the high-water and low-water periods was determined through a water budget analysis where variations were restricted to nine zones defined by land-use. All remaining variations in observed head were then assumed to be due to conduits. The model was iteratively calibrated to the high-water and low-water datasets wherein the location, size and roughness of the conduits were assigned as needed to accurately simulate observed heads and spring discharges while bounding simulated velocities by the tracer test results. Conduit diameters were adjusted to support high-water spring discharges but the locations were best determined by calibration to the low-water head field. The final model calibrated to within 5% of the total head change across the model region at 143 of the 145 wells in the high-water scenario and at 176 of the 188 wells in the low-water scenario. Simulated spring discharges fell within 13% of the observed range under high-water conditions and to within 100% of the observed range under low-water conditions. Simulated velocities ranged from as low as 10-4 m/day in the matrix to as high as 10+3 m/day in the largest conduits. The significance of these results that we emphasize here is two-fold. First, plausible karstic groundwater flow conditions can be reasonably simulated if adequate efforts are made to include springs, swallets, caves, and traced flow paths. And second, detailed saturated conduit networks can be delineated from careful evaluation of hydraulic head data particularly when dense datasets can be constructed by correlating values obtained from different wells under similar hydraulic periods.

Probability-based classifications for spatially characterizing the water temperatures and discharge rates of hot springs in the Tatun Volcanic Region, Taiwan.

PubMed

Jang, Cheng-Shin

2015-05-01

Accurately classifying the spatial features of the water temperatures and discharge rates of hot springs is crucial for environmental resources use and management. This study spatially characterized classifications of the water temperatures and discharge rates of hot springs in the Tatun Volcanic Region of Northern Taiwan by using indicator kriging (IK). The water temperatures and discharge rates of the springs were first assigned to high, moderate, and low categories according to the two thresholds of the proposed spring classification criteria. IK was then used to model the occurrence probabilities of the water temperatures and discharge rates of the springs and probabilistically determine their categories. Finally, nine combinations were acquired from the probability-based classifications for the spatial features of the water temperatures and discharge rates of the springs. Moreover, various combinations of spring water features were examined according to seven subzones of spring use in the study region. The research results reveal that probability-based classifications using IK provide practicable insights related to propagating the uncertainty of classifications according to the spatial features of the water temperatures and discharge rates of the springs. The springs in the Beitou (BT), Xingyi Road (XYR), Zhongshanlou (ZSL), and Lengshuikeng (LSK) subzones are suitable for supplying tourism hotels with a sufficient quantity of spring water because they have high or moderate discharge rates. Furthermore, natural hot springs in riverbeds and valleys should be developed in the Dingbeitou (DBT), ZSL, Xiayoukeng (XYK), and Macao (MC) subzones because of low discharge rates and low or moderate water temperatures.

Assessment of vulnerability in karst aquifers using a quantitative integrated numerical model: catchment characterization and high resolution monitoring - Application to semi-arid regions- Lebanon.

NASA Astrophysics Data System (ADS)

Doummar, Joanna; Aoun, Michel; Andari, Fouad

2016-04-01

Karst aquifers are highly heterogeneous and characterized by a duality of recharge (concentrated; fast versus diffuse; slow) and a duality of flow which directly influences groundwater flow and spring responses. Given this heterogeneity in flow and infiltration, karst aquifers do not always obey standard hydraulic laws. Therefore the assessment of their vulnerability reveals to be challenging. Studies have shown that vulnerability of aquifers is highly governed by recharge to groundwater. On the other hand specific parameters appear to play a major role in the spatial and temporal distribution of infiltration on a karst system, thus greatly influencing the discharge rates observed at a karst spring, and consequently the vulnerability of a spring. This heterogeneity can only be depicted using an integrated numerical model to quantify recharge spatially and assess the spatial and temporal vulnerability of a catchment for contamination. In the framework of a three-year PEER NSF/USAID funded project, the vulnerability of a karst catchment in Lebanon is assessed quantitatively using a numerical approach. The aim of the project is also to refine actual evapotranspiration rates and spatial recharge distribution in a semi arid environment. For this purpose, a monitoring network was installed since July 2014 on two different pilot karst catchment (drained by Qachqouch Spring and Assal Spring) to collect high resolution data to be used in an integrated catchment numerical model with MIKE SHE, DHI including climate, unsaturated zone, and saturated zone. Catchment characterization essential for the model included geological mapping and karst features (e.g., dolines) survey as they contribute to fast flow. Tracer experiments were performed under different flow conditions (snow melt and low flow) to delineate the catchment area, reveal groundwater velocities and response to snowmelt events. An assessment of spring response after precipitation events allowed the estimation of the fast infiltration component. A series of laboratory tests were performed to acquire physical values to be used as a benchmark for model parameterization, such as laboratory tests on soils for conductivity at saturation and grain size analysis. Time series used for input or calibration were collected and computed from continuous high resolution monitoring of climatic data, moisture variation in the soil, and discharge at the investigated spring. This similar model approach used on a catchment site in Germany is to be applied and validated on two pilot karst catchments in Lebanon governed by semi-arid climatic conditions. References Doummar J., Sauter M., Geyer T., 2012. Simulation of flow processes in a large scale karst system with an integrated catchment model (Mike She) - Identification of relevant parameters influencing spring discharge. Journal of Hydrology, v. 426-427- p 112-123. Jukić, D., and Denić-Jukić, V., 2009. Groundwater balance estimation in karst by using a conceptual rainfall-runoff model. Journal of Hydrology, v. 373- p 302-315

Seasonal prediction and predictability of Eurasian spring snow water equivalent in NCEP Climate Forecast System version 2 reforecasts

NASA Astrophysics Data System (ADS)

He, Qiong; Zuo, Zhiyan; Zhang, Renhe; Zhang, Ruonan

2018-01-01

The spring snow water equivalent (SWE) over Eurasia plays an important role in East Asian and Indian monsoon rainfall. This study evaluates the seasonal prediction capability of NCEP Climate Forecast System version 2 (CFSv2) retrospective forecasts (1983-2010) for the Eurasian spring SWE. The results demonstrate that CFSv2 is able to represent the climatological distribution of the observed Eurasian spring SWE with a lead time of 1-3 months, with the maximum SWE occurring over western Siberia and Northeastern Europe. For a longer lead time, the SWE is exaggerated in CFSv2 because the start of snow ablation in CFSv2 lags behind that of the observation, and the simulated snowmelt rate is less than that in the observation. Generally, CFSv2 can simulate the interannual variations of the Eurasian spring SWE 1-5 months ahead of time but with an exaggerated magnitude. Additionally, the downtrend in CFSv2 is also overestimated. Because the initial conditions (ICs) are related to the corresponding simulation results significantly, the robust interannual variability and the downtrend in the ICs are most likely the causes for these biases. Moreover, CFSv2 exhibits a high potential predictability for the Eurasian spring SWE, especially the spring SWE over Siberia, with a lead time of 1-5 months. For forecasts with lead times longer than 5 months, the model predictability gradually decreases mainly due to the rapid decrease in the model signal.

A dynamic spar numerical model for passive shape change

NASA Astrophysics Data System (ADS)

Calogero, J. P.; Frecker, M. I.; Hasnain, Z.; Hubbard, J. E., Jr.

2016-10-01

A three-dimensional constraint-driven dynamic rigid-link numerical model of a flapping wing structure with compliant joints (CJs) called the dynamic spar numerical model is introduced and implemented. CJs are modeled as spherical joints with distributed mass and spring-dampers with coupled nonlinear spring and damping coefficients, which models compliant mechanisms spatially distributed in the structure while greatly reducing computation time compared to a finite element model. The constraints are established, followed by the formulation of a state model used in conjunction with a forward time integrator, an experiment to verify a rigid-link assumption and determine a flapping angle function, and finally several example runs. Modeling the CJs as coupled bi-linear springs shows the wing is able to flex more during upstroke than downstroke. Coupling the spring stiffnesses allows an angular deformation about one axis to induce an angular deformation about another axis, where the magnitude is proportional to the coupling term. Modeling both the leading edge and diagonal spars shows that the diagonal spar changes the kinematics of the leading edge spar verses only considering the leading edge spar, causing much larger axial rotations in the leading edge spar. The kinematics are very sensitive to CJ location, where moving the CJ toward the wing root causes a stronger response, and adding multiple CJs on the leading edge spar with a CJ on the diagonal spar allows the wing to deform with larger magnitude in all directions. This model lays a framework for a tool which can be used to understand flapping wing flight.

Digital-model analysis of the effects of water-use alternatives on spring discharges Gooding and Jerome Counties, Idaho

USGS Publications Warehouse

Moreland, Joe A.

1976-01-01

Springs discharging from the Snake Plain aquifer contribute approximately 6,000 cubic feet per second (170 cubic metres per second) to flow in the Snake River between Milner and King Hill. Before irrigation began on the Snake River Plain north and east of the springs, total spring discharge was about 4,200 cubic feet per second (120 cubic meters per second). Increasing amounts of irrigated acreage from the early 1900's to the mid-1940's contributed more irrigation-return water to the aquifer resulting in increased discharge at the springs. Maximum discharge of about 6,800 cubic feet per second (190 cubic metres per second) occurred during the late 1940's and early 1950's. Increased use of pumped ground water for irrigation and changing irrigation practices have since resulted in a decline in spring discharge.

Vitamin D and Weight Cycling: Impact on Injury, Illness, and Inflammation in Collegiate Wrestlers

PubMed Central

Barcal, Jacqueline N.; Thomas, Joi T.; Hollis, Bruce W.; Austin, Kathy J.; Alexander, Brenda M.; Larson-Meyer, D. Enette

2016-01-01

This study explored the link between vitamin D status and frequency of skin infections, inflammation, and injury in college wrestlers during an academic year. Methods: Serum 25-hydroxyvitamin D (25(OH)D) (n = 19), plasma cytokine (TNF-α, IL-6, IL-10) (n = 18) concentrations, and body weight/composition were measured and injury/illness/skin infection data were collected in fall, winter, and spring. Results: In the fall, 74% of wrestlers had vitamin D concentrations <32 ng/mL which increased to 94% in winter and spring. Wrestlers lost an average of 3.4 ± 3.9 kg (p < 0.001) during the season with corresponding decreases in fat mass and increases in lean mass (p < 0.01). An inverse association between 25(OH)D concentrations and total body mass and body fat percentage was observed at all-time points (p < 0.01). Concentrations of cytokines were highly variable among individuals and did not change across time (p > 0.05). Correlations between vitamin D status, cytokines, or frequency of illness, injury, or skin infections were not observed. Conclusions: A high prevalence of vitamin D insufficiency (<32 ng/mL) and deficiency (<20 ng/mL) was observed in wrestlers and was associated with higher adiposity. It remains unclear if higher vitamin D status would reduce injury, illness, and skin infection risk. PMID:27916879

Wind assistance: A requirement for migration of shorebirds?

USGS Publications Warehouse

Butler, Robert W.; Williams, Tony D.; Warnock, Nils; Bishop, Mary Anne

1997-01-01

We investigated the importance of wind-assisted flight for northward (spring) migration by Western Sandpipers (Calidris mauri) along the Pacific Coast of North America. Using current models of energy costs of flight and recent data on the phenology of migration, we estimated the energy (fat) requirements for migration in calm winds and with wind-assisted flight for different rates of fat deposition: (1) a variable rate, assuming that birds deposit the minimum amount of fat required to reach the next stopover site; (2) a constant maximum rate of 1.0 g/day; and (3) a lower constant rate of 0.4 g/day. We tested these models by comparing conservative estimates of predicted body mass along the migration route with empirical data on body mass of Western Sandpipers at different stopover sites and upon arrival at the breeding grounds. In calm conditions, birds would have to deposit unrealistically high amounts of fat (up to 330% of observed values) to maintain body mass above absolute lean mass values. Fat-deposition rates of 1.0 g/day and 0.4 g/day, in calm conditions, resulted in a steady decline in body mass along the migration route, with predicted body masses on arrival in Alaska of only 60% (13.6 g) and 26% (5.9 g) of average lean mass (22.7 g). Conversely, birds migrating with wind assistance would be able to complete migration with fat-deposition rates as low as 0.4 g/day, similar to values reported for this size bird from field studies. Our results extend the conclusion of the importance of winds for large, long-distance migrants to a small, short-distance migrant. We suggest that the migratory decisions of birds are more strongly influenced by the frequency and duration of winds aloft, i.e. by events during the flight phase, than by events during the stopover phase of migration, such as fat-deposition rate, that have been the focus of much recent migration theory.

Sex Ratio and Body Mass of Adult Herbivorous Beetles Depend on Time of Occurrence and Light Conditions

PubMed Central

Łukowski, Adrian; Mąderek, Ewa; Giertych, Marian J.; Karolewski, Piotr

2015-01-01

Body mass and sex ratio (F/M) of folivorous insects are easily measured parameters that are commonly used to assess the effect of food quality, living conditions, and preferences on the selection of favourable sites for offspring. A study was conducted on the polyphagous beetle, Gonioctena quinquepunctata (a pest of the native Prunus padus and alien P. serotina) and on the monophagous beetle, Altica brevicollis coryletorum (a pest of Corylus avellana). Both species have a similar life cycle with emergence of current-year adults in summer, and reproduction of 1-year-old insects in spring. A. brevicollis coryletorum feeds primarily on sunlit shrubs, while G. quinquepunctata prefers shaded leaves. The present study assessed the effect of time of occurrence (insect age) on body mass in both sexes and on the sex ratio F/M, taking into account the influence of light conditions associated with their favoured food source (sunlit vs. shaded leaves). We hypothesized that a change in body mass in current-year insects would be determined by the amount of consumed food, while the sex ratio would be stable, when in 1-year-old insects females would die shortly after oviposition, while males would be active for a prolonged time. Results confirmed the hypothesis that changes in mass of current-year beetles was determined by the amount of food intake. We also found that in spring, unfertilized females coexist with fertilized ones and that the latter females live for some time after oviposition; resulting in fluctuations of the mean mass for females. In both species, 1-year-old beetles were heavier than current-year. The preference of A. brevicollis coryletorum for sunlit leaves results in a higher body weight than in G. quinquepunctata in both seasons. The data are consistent and indicate seasonal fluctuations in body mass and changes in the sex ratio in 1-year-old beetles, due to the entrance into their reproductive period. PMID:26657564

Sensing power transfer between the human body and the environment.

PubMed

Veltink, Peter H; Kortier, Henk; Schepers, H Martin

2009-06-01

The power transferred between the human body and the environment at any time and the work performed are important quantities to be estimated when evaluating and optimizing the physical interaction between the human body and the environment in sports, physical labor, and rehabilitation. It is the objective of the current paper to present a concept for estimating power transfer between the human body and the environment during free motions and using sensors at the interface, not requiring measurement systems in the environment, and to experimentally demonstrate this principle. Mass and spring loads were moved by hand over a fixed height difference via varying free movement trajectories. Kinematic and kinetic quantities were measured in the handle between the hand and the load. 3-D force and moments were measured using a 6 DOF force/moment sensor module, 3-D movement was measured using 3-D accelerometers and angular velocity sensors. The orientation was estimated from the angular velocity, using the initial orientation as a begin condition. The accelerometer signals were expressed in global coordinates using this orientation information. Velocity was estimated by integrating acceleration in global coordinates, obtained by adding gravitational acceleration to the accelerometer signals. Zero start and end velocities were used as begin and end conditions. Power was calculated as the sum of the inner products of velocity and force and of angular velocity and moment, and work was estimated by integrating power over time. The estimated performed work was compared to the potential energy difference corresponding to the change in height of the loads and appeared to be accurate within 4% for varying movements with net displacements and varying loads (mass and spring). The principle of estimating power transfer demonstrated in this paper can be used in future interfaces between the human body and the environment instrumented with body-mounted miniature 3-D force and acceleration sensors.