Fiberboards treated with N’-N-(1, 8-Naphthalyl) hydroxylamine (NHA-Na), borax, and boric acid

Treesearch

Turgay Akbulut; S. Nami Kartal; Frederick Green

2004-01-01

This paper reports on the physical and mechanical properties and decay and termite resistance of fiberboard panels made from pine and beech treated with N’-N-(1, 8-Naphthalyl) hydroxylamine sodium salt(NHA-Na), borax, and boric acid at varying loadings. The panels were manufactured using 10 percent urea-formaldehyde resin and 1 percent NH4Cl. Mechanical and physical...

The effects of dietary boron compounds in supplemented diet on hormonal activity and some biochemical parameters in rats.

PubMed

Kucukkurt, Ismail; Akbel, Erten; Karabag, Funda; Ince, Sinan

2015-03-01

The aims of this study were to clarify the effects of dietary boric acid or borax, as a boron (B) source, on hormonal status (leptin, insulin, triiodothyronine (T3), and thyroxine) and some biochemical parameter levels as glucose, carnitine, nonesterified fatty acids, and betahydroxybutyric acid in rats. A total of 30 Sprague-Dawley male rats were divided into three equal groups: the animals in the first group (control) were fed with a standard rodent diet containing 6.4 mg B/kg, and the animals in the experimental group were fed with a standard rodent diet added with boric acid and borax (100 mg B/kg) throughout the experimental period of 28 days. The B compounds especially borax decreased leptin, insulin, and glucose levels, whereas increased T3 and carnitine levels in plasma. In addition, body weight of rats was found to be low in the boric acid group at the end of 4 weeks. Consequently, our results demonstrate that B supplementation (100 mg/kg) in diet decreases body weight, leptin, and insulin, whereas increases T3 levels in plasma, so enhances the metabolic activity of rats. Between the B compounds used in this study, it was found that borax had a greater effect on hormonal status than boric acid. © The Author(s) 2012.

Prediction of Layer Thickness in Molten Borax Bath with Genetic Evolutionary Programming

NASA Astrophysics Data System (ADS)

Taylan, Fatih

2011-04-01

In this study, the vanadium carbide coating in molten borax bath process is modeled by evolutionary genetic programming (GEP) with bath composition (borax percentage, ferro vanadium (Fe-V) percentage, boric acid percentage), bath temperature, immersion time, and layer thickness data. Five inputs and one output data exist in the model. The percentage of borax, Fe-V, and boric acid, temperature, and immersion time parameters are used as input data and the layer thickness value is used as output data. For selected bath components, immersion time, and temperature variables, the layer thicknesses are derived from the mathematical expression. The results of the mathematical expressions are compared to that of experimental data; it is determined that the derived mathematical expression has an accuracy of 89%.

40 CFR 415.282 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... point source subject to this subpart and using borax produced by the Trona process must achieve the... remined borax must achieve the following effluent limitations representing the degree of effluent...): Subpart AB—Boric Acid Mined Borax Process Pollutant or pollutant property BPT limitations Maximum for any...

40 CFR 415.282 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... point source subject to this subpart and using borax produced by the Trona process must achieve the... remined borax must achieve the following effluent limitations representing the degree of effluent...): Subpart AB—Boric Acid Mined Borax Process Pollutant or pollutant property BPT limitations Maximum for any...

40 CFR 415.282 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... point source subject to this subpart and using borax produced by the Trona process must achieve the... remined borax must achieve the following effluent limitations representing the degree of effluent...): Subpart AB—Boric Acid Mined Borax Process Pollutant or pollutant property BPT limitations Maximum for any...

40 CFR 415.282 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... point source subject to this subpart and using borax produced by the Trona process must achieve the... remined borax must achieve the following effluent limitations representing the degree of effluent...): Subpart AB—Boric Acid Mined Borax Process Pollutant or pollutant property BPT limitations Maximum for any...

40 CFR 415.282 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... point source subject to this subpart and using borax produced by the Trona process must achieve the... remined borax must achieve the following effluent limitations representing the degree of effluent...): Subpart AB—Boric Acid Mined Borax Process Pollutant or pollutant property BPT limitations Maximum for any...

Boron Tolerance in Aspergillus nidulans Is Sustained by the SltA Pathway Through the SLC-Family Transporters SbtA and SbtB

PubMed Central

Villarino, María; Mendizabal, Gorka; Garzia, Aitor; Ugalde, Unai

2017-01-01

Microbial cells interact with the environment by adapting to external changes. Signal transduction pathways participate in both sensing and responding in the form of modification of gene expression patterns, enabling cell survival. The filamentous fungal-specific SltA pathway regulates tolerance to alkalinity, elevated cation concentrations and, as shown in this work, also stress conditions induced by borates. Growth of sltA− mutants is inhibited by increasing millimolar concentrations of boric acid or borax (sodium tetraborate). In an attempt to identify genes required for boron-stress response, we determined the boric acid or borax-dependent expression of sbtA and sbtB, orthologs of Saccharomyces cerevisiae bor1, and a reduction in their transcript levels in a ΔsltA mutant. Deletion of sbtA, but mainly that of sbtB, decreased the tolerance to boric acid or borax. In contrast, null mutants of genes coding for additional transporters of the Solute Carrier (SLC) family, sB, sbtD or sbtE, showed an unaltered growth pattern under the same stress conditions. Taken together, our results suggest that the SltA pathway induces, through SbtA and SbtB, the export of toxic concentrations of borates, which have largely recognized antimicrobial properties. PMID:28753996

In vivo percutaneous absorption of boric acid, borax, and disodium octaborate tetrahydrate in humans compared to in vitro absorption in human skin from infinite and finite doses.

PubMed

Wester, R C; Hui, X; Hartway, T; Maibach, H I; Bell, K; Schell, M J; Northington, D J; Strong, P; Culver, B D

1998-09-01

Literature from the first half of this century report concern for toxicity from topical use of boric acid, but assessment of percutaneous absorption has been impaired by lack of analytical sensitivity. Analytical methods in this study included inductively coupled plasma-mass spectrometry which now allows quantitation of percutaneous absorption of 10B in 10B-enriched boric acid, borax, and disodium octaborate tetrahydrate (DOT) in biological matrices. This made it possible, in the presence of comparatively large natural dietary boron intakes for the in vivo segment of this study, to quantify the boron passing through skin. Human volunteers were dosed with 10B-enriched boric acid, 5.0%, borax, 5.0%, or disodium octaborate tetrahydrate, 10%, in aqueous solutions. Urinalysis, for boron and changes in boron isotope ratios, was used to measure absorption. Boric acid in vivo percutaneous absorption was 0.226 (SD = 0.125) mean percentage dose, with flux and permeability constant (Kp) calculated at 0.009 microgram/cm2/h and 1.9 x 10(-7) cm/h, respectively. Borax absorption was 0.210 (SD = 0.194) mean percentage of dose, with flux and Kp calculated at 0.009 microgram/cm2/h and 1.8 x 10(-7) cm/h, respectively. DOT absorption was 0.122 (SD = 0.108) mean percentage, with flux and Kp calculated at 0.01 microgram/cm2/h and 1.0 x 10(-7) cm/h, respectively. Pretreatment with the potential skin irritant 2% sodium lauryl sulfate had no effect on boron skin absorption. In vitro human skin percentage of doses of boric acid absorbed were 1.2 for a 0.05% solution, 0.28 for a 0.5% solution, and 0.70 for a 5.0% solution. These absorption amounts translated into flux values of, respectively, 0.25, 0.58, and 14.58 micrograms/cm2/h and permeability constants (Kp) of 5.0 x 10(-4), 1.2 x 10(-4), and 2.9 x 10(-4) cm/h for the 0.05, 0.5, and 5.0% solutions. The above in vitro doses were at infinite, 1000 microliters/cm2 volume. At 2 microliters/cm2 (the in vivo dosing volume), flux decreased some 200-fold to 0.07 microgram/cm2/h and Kp of 1.4 x 10(-6) cm/h, while percentage of dose absorbed was 1.75%. Borax dosed at 5.0%/1000 microliters/cm2 had 0.41% dose absorbed, flux at 8.5 micrograms/cm2/h, and Kp was 1.7 x 10(-4) cm/h. Disodium octaborate tetrahydrate (DOT) dosed at 10%/1000 microliters/cm2 was 0.19% dose absorbed, flux at 7.9 micrograms/cm2/h, and Kp was 0.8 x 10(-4) cm/h. These in vitro results from infinite doses (1000 microliters/cm2) were 1000-fold greater than those obtained in the companion in vivo study. The results from the finite (2 microliters/cm2) dosing were closer (10-fold difference) to the in vivo results. General application of infinite dose percutaneous absorption values for risk assessment is questioned by these results. These in vivo results show that percutaneous absorption of boron, as boric acid, borax, and disodium octaborate tetrahydrate, through intact human skin, is low and is significantly less than the average daily dietary intake. This very low boron skin absorption makes it apparent that, for the borates tested, the use of gloves to prevent systemic uptake is unnecessary. These findings do not apply to abraded or otherwise damaged skin.

Borates

USGS Publications Warehouse

Crangle, R.D.

2013-01-01

Four minerals represent 90 percent of the borates used by industry worldwide — the sodium borates (tincal and kernite), calcium borate (colemanite) and the sodium-calcium borate (ulexite). Borax is a white crystalline substance, chemically known as sodium tetraborate decahydrate, and is found naturally as the mineral tincal. Boric acid is a colorless crystalline solid sold in technical, national formulary and special quality grades as granules or powder and marketed most often as anhydrous boric acid. Deposits of borates are associated with volcanic activity and arid climates, with the largest economically viable deposits located in the Mojave Desert of the United States near Boron, CA, the Alpide belt in southern Asia and the Andean belt of South America.

Effect of various fire retardants on surface roughness of plywood

Treesearch

Nadir Ayrilmis; Suleyman Korkut; Ercan Tanritanir; Jerrold E. Winandy; Salim Hiziroglu

2006-01-01

In this study the surface roughness of plywood treated with various fire retardants was investigated. Commercially manufactured veneer of Akaba wood (Tetraberlinia bifoliolata) was treated with borax, boric acid, monoammonium phosphate and diammonium phosphate, then experimental plywood panels were made from these veneer sheets. A stylus method was employed to evaluate...

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) PRIOR-SANCTIONED..., based on available scientific information and data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate.* Borax or boric acid for use in adhesives, sizes, and coatings.* Butadiene-styrene copolymer. Chromium...

Effect of boron and phosphate compounds on physical, mechanical, and fire properties of wood-polypropylene composites

Treesearch

Nadir Ayrilmis; Turgay Akbulut; Turker Dundar; Robert H. White; Fatih Mengeloglu; Umit Buyuksari; Zeki Candan; Erkan Avci

2012-01-01

Physical, mechanical, and fire properties of the injection-molded wood flour/polypropylene composites incorporated with different contents of boron compounds; borax/boric acid and zinc borate, and phosphate compounds; mono and diammonium phosphates were investigated. The effect of the coupling agent content, maleic anhydride-grafted polypropylene, on the properties of...

Physical, mechanical, and fire properties of oriented strandboard with fire retardant treated veneers

Treesearch

Nadir Ayrilmis; Zeki Candan; Robert White

2007-01-01

This study evaluated physical, mechanical and fire properties of oriented strand boards (OSB) covered with fire retardant treated veneers. The beech (Fagus orientalis Lipsky) veneers were treated with either monoammonium phosphate, diammonium phosphate, lime water or a borax/boric acid (1 : 1 by weight) mixture. Physical and mechanical properties of the specimens were...

Effect of Boron and Phosphate compounds on Thermal and Fire Properties of wood/HDPE composites

Treesearch

Turgay Akbulut; Nadir Ayrilmis; Turker Dundar; Ali Durmus; Robert H. White; Murat Teker

2011-01-01

Melting and non-isothermal crystallization behaviors, oxidative induction time, and fire performance of the injection-molded wood flour-high density polyethylene (HDPE) composites (WPCs) incorporated with different levels (4, 8, or 12 wt %) of boron compounds [borax/boric acid (BX/BA) (0.5:0.5 wt %), zinc borate (ZB)] and phosphorus compounds [mono- and di-ammonium...

Is Boron a Prebiotic Element? A Mini-review of the Essentiality of Boron for the Appearance of Life on Earth

NASA Astrophysics Data System (ADS)

Scorei, Romulus

2012-02-01

Boron is probably a prebiotic element with special importance in the so-called "sugars world". Boron is not present on Earth in its elemental form. It is found only in compounds, e.g., borax, boric acid, kernite, ulexite, colemanite and other borates. Volcanic spring waters sometimes contain boron-based acids (e.g., boric, metaboric, tetraboric and pyroboric acid). Borates influence the formation of ribofuranose from formaldehyde that feeds the "prebiotic metabolic cycle". The importance of boron in the living world is strongly related to its implications in the prebiotic origins of genetic material; consequently, we believe that throughout the evolution of life, the primary role of boron has been to provide thermal and chemical stability in hostile environments. The complexation of boric acid and borates with organic cis-diols remains the most probable chemical mechanism for the role of this element in the evolution of the living world. Because borates can stabilize ribose and form borate ester nucleotides, boron may have provided an essential contribution to the "pre-RNA world".

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2014 CFR

2014-04-01

... data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate.* Borax or boric acid for use in adhesives... paperboard which is waxed.* Hexamethylene tetramine as a setting agent for protein, including casein.* 1-(2... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Substances used in the manufacture of paper and...

Effect of boron compounds on physical, mechanical, and fire properties of injection molded wood plastic composites

Treesearch

Nadir Ayrilmis; Turgay Akbulut; Turker Dundar; Robert H. White; Fatih Mengeloglu; Zeki Candan; Umit Buyuksari; Erkan Avci

2011-01-01

Physical, mechanical, and fire properties of the injection-molded wood flour/polypropylene composites (WPCs) incorporated with different levels of boron compounds, borax/boric acid (BX/BA) (0.5:0.5 wt %) and zinc borate (ZB) (4, 8, or 12 wt %) were investigated. The effect of the coupling agent loading (2, 4, or 6 wt %), maleic anhydride-grafted PP (MAPP), on the...

Accidental mold/termite testing of high density fiberboard (HDF) treated with borates and N’N-naphthaloylhydroxylamine (NHA)

Treesearch

S. Nami Kartal; Harold H. Burdsall; Frederick Green

2003-01-01

High density fibreboard (HDF) was made from beech and pine furnish (50:50) and treated with boric acid (0.1-3%), borax (0.1-3%) or N'-N-(1,8- naphthalyl) hydroxylamine (NHA) (0.1-1%) prior to gluing with urea formaldehyde (UF) resin in order to determine resistance to Eastern subterranean termites ( Reticulitermes flavipes Kollar), the most economically important...

Chemical disposition of boron in animals and humans.

PubMed Central

Moseman, R F

1994-01-01

Elemental boron was isolated in 1808. It typically occurs in nature as borates hydrated with varying amounts of water. Important compounds are boric acid and borax. Boron compounds are also used in the production of metals, enamels, and glasses. In trace amounts, boron is essential for the growth of many plants, and is found in animal and human tissues at low concentrations. Poisoning in humans has been reported as the result of accidental ingestion or use of large amounts in the treatment of burns. Boron as boric acid is fairly rapidly absorbed and excreted from the body via urine. The half-life of boric acid in humans is on the order of 1 day. Boron does not appear to accumulate in soft tissues of animals, but does accumulate in bone. Normal levels of boron in soft tissues, urine, and blood generally range from less than 0.05 ppm to no more than 10 ppm. In poisoning incidents, the amount of boric acid in brain and liver tissue has been reported to be as high as 2000 ppm. Recent studies at the National Institute of Environmental Health Sciences have indicated that boron may contribute to reduced fertility in male rodents fed 9000 ppm of boric acid in feed. Within a few days, boron levels in blood and most soft tissues quickly reached a plateau of about 15 ppm. Boron in bone did not appear to plateau, reaching 47 ppm after 7 days on the diet. Cessation of exposure to dietary boron resulted in a rapid drop in bone boron.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7889870

An introduction to boron: history, sources, uses, and chemistry.

PubMed Central

Woods, W G

1994-01-01

Following a brief overview of the terrestrial distribution of boron in rocks, soil, and water, the history of the discovery, early utilization, and geologic origin of borate minerals is summarized. Modern uses of borate-mineral concentrates, borax, boric acid, and other refined products include glass, fiberglass, washing products, alloys and metals, fertilizers, wood treatments, insecticides, and microbiocides. The chemistry of boron is reviewed from the point of view of its possible health effects. It is concluded that boron probably is complexed with hydroxylated species in biologic systems, and that inhibition and stimulation of enzyme and coenzymes are pivotal in its mode of action. Images Figure 1. PMID:7889881

The fracture toughness of borides formed on boronized cold work tool steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sen, Ugur; Sen, Saduman

2003-06-15

In this study, the fracture toughness of boride layers of two borided cold work tool steels have been investigated. Boriding was carried out in a salt bath consisting of borax, boric acid, ferro-silicon and aluminum. Boriding was performed at 850 and 950 deg. C for 2 to 7 h. The presence of boride phases were determined by X-ray diffraction (XRD) analysis. Hardness and fracture toughness of borides were measured via Vickers indenter. Increasing of boriding time and temperature leads to reduction of fracture toughness of borides. Metallographic examination showed that boride layer formed on cold work tool steels was compactmore » and smooth.« less

Identification of delamination failure of boride layer on common Cr-based steels

NASA Astrophysics Data System (ADS)

Taktak, Sukru; Tasgetiren, Suleyman

2006-10-01

Adhesion is an important aspect in the reliability of coated components. With low-adhesion of interfaces, different crack paths may develop depending on the local stress field at the interface and the fracture toughness of the coating, substrate, and interface. In the current study, an attempt has been made to identify the delamination failure of coated Cr-based steels by boronizing. For this reason, two commonly used steels (AISI H13, AISI 304) are considered. The steels contain 5.3 and 18.3 wt.% Cr, respectively. Boriding treatment is carried out in a slurry salt bath consisting of borax, boric acid, and ferrosilicon at a temperature range of 800 950 °C for 3, 5, and 7 h. The general properties of the boron coating are obtained by mechanical and metallographic characterization tests. For identification of coating layer failure, some fracture toughness tests and the Daimler-Benz Rockwell-C adhesion test are used.

The antimicrobial effect of boric acid on Trichomonas vaginalis.

PubMed

Brittingham, Andrew; Wilson, Wayne A

2014-12-01

The treatment options for trichomoniasis are largely limited to nitroimidazole compounds (metronidazole and tinidazole). Few alternatives exist in cases of recalcitrant infections or in cases of nitroimidazole hypersensitivity. Recently, the intravaginal administration of boric acid has been advocated as an alternative treatment of trichomoniasis. However, no in vitro studies are available that directly assess the sensitivity of Trichomonas vaginalis to boric acid. We examined the sensitivity of common laboratory strains and recent clinical isolates of T. vaginalis to boric acid. The effect of increasing concentrations of boric acid on parasite growth and viability was determined, and a minimal lethal concentration was reported. The effect of pH on boric acid toxicity was assessed and compared with that of lactic and acetic acid. Boric acid is microbicidal to T. vaginalis, and its antitrichomonal activity is independent of environmental acidification. Unlike acetic acid and lactic acid, boric acid exposure results in growth suppression and lethality over a wide range of pH (5-7) and under conditions that are normally permissible for growth in vitro. The microbicidal effect of boric acid on T. vaginalis, coupled with its previous clinical use in treating vaginal candidiasis, supports the continued inclusion of boric acid in the therapeutic arsenal for treating trichomoniasis.

Synergistic effect of EDTA and boric acid on corneal penetration of CS-088.

PubMed

Kikuchi, Takayuki; Suzuki, Masahiko; Kusai, Akira; Iseki, Ken; Sasaki, Hitoshi

2005-02-16

In order to investigate the effects of EDTA and boric acid (EDTA/boric acid) on the corneal penetration of CS-088, an ophthalmic agent, the apparent permeability coefficient of CS-088 in the presence of EDTA/boric acid across the isolated corneal membranes of rabbits was measured using an in vitro penetration chamber system. FITC-dextran (M.W. 4400) and an electrical method based on membrane resistance were used to provide a quantitative assessment of the enhancing effect of EDTA/boric acid. The corneal penetration of CS-088 was significantly enhanced in the presence of EDTA/boric acid by approximately 1.6-fold. The permeability-enhancing effect of EDTA/boric acid was apparently synergistic and concentration-dependent on both EDTA and boric acid. The penetration of FITC-dextran, a paracellular marker, and electrical resistance of corneal membranes were not affected in the presence of EDTA/boric acid. Furthermore, no enhancing effect of EDTA/boric acid was observed in de-epithelialized corneas, although de-epithelialized corneas exhibited a markedly higher permeability of CS-088 that was 24-fold greater than that for intact corneas. In conclusion, EDTA/boric acid synergistically enhances the transcellular permeability of CS-088 in the outer layer but not in the inner layers of the corneal membrane.

Antifungal mechanisms supporting boric acid therapy of Candida vaginitis.

PubMed

De Seta, Francesco; Schmidt, Martin; Vu, Bao; Essmann, Michael; Larsen, Bryan

2009-02-01

Boric acid is a commonly cited treatment for recurrent and resistant yeast vaginitis, but data about the extent and mechanism of its antifungal activity are lacking. The aim of this study was to use in vitro methods to understand the spectrum and mechanism of boric acid as a potential treatment for vaginal infection. Yeast and bacterial isolates were tested by agar dilution to determine the intrinsic antimicrobial activity of boric acid. Established microbial physiology methods illuminated the mechanism of the action of boric acid against Candida albicans. C. albicans strains (including fluconazole-resistant strains) were inhibited at concentrations attainable intravaginally; as were bacteria. Broth dilution MICs were between 1563 and 6250 mg/L and boric acid proved fungistatic (also reflected by a decrease in CO(2) generation); prolonged culture at 50,000 mg/L was fungicidal. Several organic acids in yeast nitrogen broth yielded a lower pH than equimolar boric acid and sodium borate but were less inhibitory. Cold or anaerobic incubation protected yeast at high boric acid concentrations. Cells maintained integrity for 6 h in boric acid at 37 degrees C, but after 24 h modest intrusion of propidium iodide occurred; loss of plate count viability preceded uptake of vital stain. Growth at sub-MIC concentrations of boric acid decreased cellular ergosterol. The drug efflux pump CDR1 did not protect Candida as CDR1 expression was abrogated by boric acid. Boric acid interfered with the development of biofilm and hyphal transformation. Boric acid is fungistatic to fungicidal depending on concentration and temperature. Inhibition of oxidative metabolism appears to be a key antifungal mechanism, but inhibition of virulence probably contributes to therapeutic efficacy in vivo.

Recovery of boric acid from ion exchangers

DOEpatents

Pollock, Charles W.

1976-01-01

The recovery of boric acid from an anion exchange resin is improved by eluting the boric acid with an aqueous solution of ammonium bicarbonate. The boric acid can be readily purified and concentrated by distilling off the water and ammonium bicarbonate. This process is especially useful for the recovery of boric acid containing a high percentage of .sup.10 B which may be found in some nuclear reactor coolant solutions.

Boric acid ovicidal trap for the management of Aedes species.

PubMed

Bhami, L Charlet; Das, S Sam Manohar

2015-06-01

The use of low concentrations of boric acid as a potential and effective control agent for the eggs and immature stages of Aedes aegypti L. and Aedes albopictus Skuse (Diptera: Culicidae) is found to be safe and effective as compared to synthetic chemical insecticides. The study aims to determine the ovicidal concentration of boric acid, its effective concentration for oviposition attraction and the larval mortality concentration for Ae. aegypti and Ae. albopictus. The ovicidal concentration of boric acid was determined by incubating the eggs in different concentrations of boric acid (0.1, 0.25, 0.5, 0.75 and 1%). Different dilutions of boric acid were taken in the oviposition cup and the ovicidal concentration, effective concentration for oviposition attraction and the mean survival/mortality rate of III and IV instar Ae. aegypti and Ae. albopictus larvae were determined. The ovicidal concentration of boric acid for 100% mortality in Aedes sp eggs is 1%. Effective concentration for the oviposition attraction is 0.5%. At 1% concentration, larvae of both the species died within 24 h. Boric acid is less toxic compared to different pesticides, and in low concentrations, it attracts the ovipositing female Aedes sp as well as fertile males. Dilute boric acid solution is an effective ovitrap since the eggs laid by mosquitoes either die or the larvae that hatch out from them do not survive in boric acid. Boric acid kills the males that come in contact with the solution, which are attracted to the trap by the females hovering around.

Investigation of phase stability of poly(1-oxotrimethylene)-dissolved aqueous solutions containing ZnCl2/CaCl2/LiCl: Influence of boric acid introduction and aging time

NASA Astrophysics Data System (ADS)

Chae, Dong Wook; Jang, Han Beol; Kim, Byoung Chul

2018-02-01

Poly(1-oxotrimethylene) (POTM) was dissolved in aqueous solutions containing ZnCl2, CaCl2, and LiCl, and the effects of boric acid introduction on the phase stability of the POTM solutions over various aging times were investigated. In the absence of boric acid, aging at 70°C for 8 h notably reduced the loss tangent (tanδ) for the 7.0 wt.% POTM solutions. Addition of boric acid into unaged solutions had little effect on tanδ over the frequency range measured, regardless of its content, whereas addition of 0.3-1.0 wt.% of boric acid into aged solutions increased tanδ. The dynamic viscosity of the POTM solutions with 1.0 wt.% boric acid was affected little by aging time. Conversely, the POTM solutions without boric acid exhibited increased dynamic viscosity in the low-frequency range with aging time. In addition, the slope of the solutions in the Cole-Cole plot decreased with increasing aging time in the absence of boric acid, whereas aging time had little effect in the presence of 1.0 wt.% boric acid. For dilute POTM solutions ( i.e., 0.5 g/dL), the reduced viscosity decreased with increasing aging time in the absence of boric acid, while it was affected little in solutions with the addition of 1.0 wt.% boric acid. In the UV-Vis spectra, the aging-time-dependent increase of the absorbance peak at 390 nm was associated with the generation of a chromophoric complex in the POTM solutions. Conversely, the disappearance of the peak due to the addition of boric acid indicated suppression of complex formation.

Chemical Reaction between Boric Acid and Phosphine Indicates Boric Acid as an Antidote for Aluminium Phosphide Poisoning.

PubMed

Soltani, Motahareh; Shetab-Boushehri, Seyed F; Shetab-Boushehri, Seyed V

2016-08-01

Aluminium phosphide (AlP) is a fumigant pesticide which protects stored grains from insects and rodents. When it comes into contact with moisture, AlP releases phosphine (PH3), a highly toxic gas. No efficient antidote has been found for AlP poisoning so far and most people who are poisoned do not survive. Boric acid is a Lewis acid with an empty p orbital which accepts electrons. This study aimed to investigate the neutralisation of PH3 gas with boric acid. This study was carried out at the Baharlou Hospital, Tehran University of Medical Sciences, Tehran, Iran, between December 2013 and February 2014. The volume of released gas, rate of gas evolution and changes in pH were measured during reactions of AlP tablets with water, acidified water, saturated boric acid solution, acidified saturated boric acid solution, activated charcoal and acidified activated charcoal. Infrared spectroscopy was used to study the resulting probable adduct between PH3 and boric acid. Activated charcoal significantly reduced the volume of released gas (P <0.01). Although boric acid did not significantly reduce the volume of released gas, it significantly reduced the rate of gas evolution (P <0.01). A gaseous adduct was formed in the reaction between pure AlP and boric acid. These findings indicate that boric acid may be an efficient and non-toxic antidote for PH3 poisoning.

Effects of boric acid on the healing of Achilles tendons of rats.

PubMed

Kaymaz, Burak; Gölge, Umut Hatay; Ozyalvaclı, Gulzade; Kömürcü, Erkam; Goksel, Ferdi; Mermerkaya, Musa Ugur; Doral, Mahmut Nedim

2016-12-01

Tendinous lesions are among the most frequent pathologies encountered in sportsmen. The objectives of new treatments are to improve the healing process and reduce the recovery time. Boron plays an important role in the wound repair process by increasing components of extracellular matrix and angiogenesis. This animal study aimed to investigate the effect of boric acid on healing of the Achilles tendon. The right Achilles tendons of 40 rats were completely sectioned, and the rats were randomly divided into five groups. Each group consisted of eight rats. Groups 1 and 2 were oral boric acid groups with the doses of 4 and 8 mg/kg/day boric acid, respectively. Group 3 was the local boric acid group (8 mg/kg boric acid intratendinous injection). Group 4 was administered both oral and local boric acid (8 mg/kg/day orally and 8 mg/kg boric acid intratendinous injection), and group 5 was the control group with no boric acid application. At the end of the fourth week, all the rats were killed and histopathological examination of the Achilles tendon repair site was made. Histopathological examination of the tissue sections revealed more properly oriented collagen fibres, more normal cellular distribution of tenocytes and more properly organized vascular bundles in group 1 and group 2, which were the groups administered oral boric acid. Pathological sum scores of groups 1 and 2 were less than those of the other groups, and the differences between the oral boric acid groups (group 1 and group 2) and the other three groups (groups 3, 4 and 5) were statistically significant (p = 0.001). As boric acid is safe and toxicity even after very high doses is unusual, oral boric acid may be used as an agent to improve the healing process of tendon injuries. However, biomechanical tests should also be performed to show the effect of boric acid on strength and endurance of the tendon before it can be used in clinical practice.

Enhancing fluorescence intensity of Ellagic acid in Borax-HCl-CTAB micelles

NASA Astrophysics Data System (ADS)

Wang, Feng; Huang, Wei; Zhang, Shuai; Liu, Guokui; Li, Kexiang; Tang, Bo

2011-03-01

Ellagic acid (C 14H 6O 8), a naturally occurring phytochemical, found mainly in berries and some nuts, has anticarcinogenic and antioxidant properties. It is found that fluorescence of Ellagic acid (EA) is greatly enhanced by micelle of cetyltrimethylammonium bromide (CTAB) surfactant. Based on this effect, a sensitive proposed fluorimetric method was applied for the determination of Ellagic acid in aqueous solution. In the Borax-HCl buffer, the fluorescence intensity of Ellagic acid in the presence of CTAB is proportional to the concentration of Ellagic acid in range from 8.0 × 10 -10 to 4.0 × 10 -5 mol L -1; and the detection limits are 3.2 × 10 -10 mol L -1 and 5.9 × 10 -10 mol L -1 excited at 266 nm and 388 nm, respectively. The actual samples of pomegranate rinds are simply manipulated and satisfactorily determined. The interaction mechanism studies argue that the negative EA-Borax complex is formed and solubilized in the cationic surfactant CTAB micelle in this system. The fluorescence intensity of EA enhances because the CTAB micelle provides a hydrophobic microenvironment for EA-Borax complex, which can prevent collision with water molecules and decrease the energy loss of EA-Borax complex.

Chemical Reaction between Boric Acid and Phosphine Indicates Boric Acid as an Antidote for Aluminium Phosphide Poisoning

PubMed Central

Soltani, Motahareh; Shetab-Boushehri, Seyed F.; Shetab-Boushehri, Seyed V.

2016-01-01

Objectives: Aluminium phosphide (AlP) is a fumigant pesticide which protects stored grains from insects and rodents. When it comes into contact with moisture, AlP releases phosphine (PH3), a highly toxic gas. No efficient antidote has been found for AlP poisoning so far and most people who are poisoned do not survive. Boric acid is a Lewis acid with an empty p orbital which accepts electrons. This study aimed to investigate the neutralisation of PH3 gas with boric acid. Methods: This study was carried out at the Baharlou Hospital, Tehran University of Medical Sciences, Tehran, Iran, between December 2013 and February 2014. The volume of released gas, rate of gas evolution and changes in pH were measured during reactions of AlP tablets with water, acidified water, saturated boric acid solution, acidified saturated boric acid solution, activated charcoal and acidified activated charcoal. Infrared spectroscopy was used to study the resulting probable adduct between PH3 and boric acid. Results: Activated charcoal significantly reduced the volume of released gas (P <0.01). Although boric acid did not significantly reduce the volume of released gas, it significantly reduced the rate of gas evolution (P <0.01). A gaseous adduct was formed in the reaction between pure AlP and boric acid. Conclusion: These findings indicate that boric acid may be an efficient and non-toxic antidote for PH3 poisoning. PMID:27606109

Effect of boric acid supplementation of ostrich water on the expression of Foxn1 in thymus.

PubMed

Xiao, Ke; Ansari, Abdur Rahman; Rehman, Zia Ur; Khaliq, Haseeb; Song, Hui; Tang, Juan; Wang, Jing; Wang, Wei; Sun, Peng-Peng; Zhong, Juming; Peng, Ke-Mei

2015-11-01

Foxn1 is essential for thymus development. The relationship between boric acid and thymus development, optimal dose of boric acid in ostrich diets, and the effects of boric acid on the expression of Foxn1 were investigated in the present study. Thirty healthy ostriches were randomly divided into six groups: Group I, II, III, IV, V, VI, and supplemented with boric acid at the concentration of 0 mg/L, 40 mg/L, 80 mg/L, 160 mg/L, 320 mg/L, 640 mg/L, respectively. The histological changes in thymus were observed by HE staining, and the expression of Foxn1 analyzed by immunohistochemistry and western blot. TUNEL method was used to label the apoptotic cells. Ostrich Foxn1 was sequenced by Race method. The results were as following: Apoptosis in ostrich thymus was closely related with boric acid concentrations. Low boric acid concentration inhibited apoptosis in thymus, but high boric acid concentration promoted apoptosis. Foxn1-positive cells were mainly distributed in thymic medulla and rarely in cortex. Foxn1 is closely related to thymus growth and development. The nucleotide sequence and the encoded protein of Foxn1 were 2736 bases and 654 amino acids in length. It is highly conserved as compared with other species. These results demonstrated that the appropriate boric acid supplementation in water would produce positive effects on the growth development of ostrich thymus by promoting Foxn1 expression, especially at 80 mg/L, and the microstructure of the thymus of ostrich fed 80 mg/L boric acid was well developed. The supplementation of high dose boron (>320 mg/L) damaged the microstructure of thymus and inhibited the immune function by inhibiting Foxn1 expression, particularly at 640 mg/L. The optimal dose of boric acid supplementation in ostrich diets is 80 mg/L boric acid. The genomic full-length of African ostrich Foxn1 was cloned for the first time in the study.

40 CFR 721.1875 - Boric acid, alkyl and substituted alkyl esters (generic name).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Boric acid, alkyl and substituted... Significant New Uses for Specific Chemical Substances § 721.1875 Boric acid, alkyl and substituted alkyl... chemical substance boric acid, alkyl and substituted alkyl esters (PMN P-86-1252) is subject to reporting...

40 CFR 721.1875 - Boric acid, alkyl and substituted alkyl esters (generic name).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Boric acid, alkyl and substituted... Significant New Uses for Specific Chemical Substances § 721.1875 Boric acid, alkyl and substituted alkyl... chemical substance boric acid, alkyl and substituted alkyl esters (PMN P-86-1252) is subject to reporting...

40 CFR 721.1875 - Boric acid, alkyl and substituted alkyl esters (generic name).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Boric acid, alkyl and substituted... Significant New Uses for Specific Chemical Substances § 721.1875 Boric acid, alkyl and substituted alkyl... chemical substance boric acid, alkyl and substituted alkyl esters (PMN P-86-1252) is subject to reporting...

40 CFR 721.1875 - Boric acid, alkyl and substituted alkyl esters (generic name).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Boric acid, alkyl and substituted... Significant New Uses for Specific Chemical Substances § 721.1875 Boric acid, alkyl and substituted alkyl... chemical substance boric acid, alkyl and substituted alkyl esters (PMN P-86-1252) is subject to reporting...

40 CFR 721.1875 - Boric acid, alkyl and substituted alkyl esters (generic name).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Boric acid, alkyl and substituted... Significant New Uses for Specific Chemical Substances § 721.1875 Boric acid, alkyl and substituted alkyl... chemical substance boric acid, alkyl and substituted alkyl esters (PMN P-86-1252) is subject to reporting...

Nonclinical safety evaluation of boric acid and a novel borate-buffered contact lens multi-purpose solution, Biotrue™ multi-purpose solution.

PubMed

Lehmann, David M; Cavet, Megan E; Richardson, Mary E

2010-12-01

Multipurpose solutions (MPS) often contain low concentrations of boric acid as a buffering agent. Limited published literature has suggested that boric acid and borate-buffered MPS may alter the corneal epithelium; an effect attributed to cytotoxicity induced by boric acid. However, this claim has not been substantiated. We investigated the effect of treating cells with relevant concentrations of boric acid using two cytotoxicity assays, and also assessed the impact of boric acid on corneal epithelial barrier function by measuring TEER and immunostaining for tight junction protein ZO-1 in human corneal epithelial cells. Boric acid was also assessed in an in vivo ocular model when administered for 28 days. Additionally, we evaluated Biotrue multi-purpose solution, a novel borate-buffered MPS, alone and with contact lenses for ocular compatibility in vitro and in vivo. Boric acid passed both cytotoxicity assays and did not alter ZO-1 distribution or corneal TEER. Furthermore, boric acid was well-tolerated on-eye following repeated administration in a rabbit model. Finally, Biotrue multi-purpose solution demonstrated good ocular biocompatibility both in vitro and in vivo. This MPS was not cytotoxic and was compatible with the eye when administered alone and when evaluated with contact lenses. We demonstrate that boric acid and a borate-buffered MPS is compatible with the ocular environment. Our findings provide evidence that ocular effects reported for some borate-buffered MPS may be incorrectly attributed to boric acid and are more likely a function of the unique combination of ingredients in the MPS formulation tested. Copyright © 2010 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Boric acid and boronic acids inhibition of pigeonpea urease.

PubMed

Reddy, K Ravi Charan; Kayastha, Arvind M

2006-08-01

Urease from the seeds of pigeonpea was competitively inhibited by boric acid, butylboronic acid, phenylboronic acid, and 4-bromophenylboronic acid; 4-bromophenylboronic acid being the strongest inhibitor, followed by boric acid > butylboronic acid > phenylboronic acid, respectively. Urease inhibition by boric acid is maximal at acidic pH (5.0) and minimal at alkaline pH (10.0), i.e., the trigonal planar B(OH)3 form is a more effective inhibitor than the tetrahedral B(OH)4 -anionic form. Similarly, the anionic form of phenylboronic acid was least inhibiting in nature.

Recycling of lead solder dross, Generated from PCB manufacturing

NASA Astrophysics Data System (ADS)

Lucheva, Biserka; Tsonev, Tsonio; Iliev, Peter

2011-08-01

The main purpose of this work is to analyze lead solder dross, a waste product from manufacturing of printed circuit boards by wave soldering, and to develop an effective and environmentally sound technology for its recycling. A methodology for determination of the content and chemical composition of the metal and oxide phases of the dross is developed. Two methods for recycling of lead solder dross were examined—carbothermal reduction and recycling using boron-containing substances. The influence of various factors on the metal yield was studied and the optimal parameters of the recycling process are defined. The comparison between them under the same parameters-temperature and retention time, showed that recycling of dross with a mixture of borax and boric acid in a 1:2 ratio provides higher metal yield (93%). The recycling of this hazardous waste under developed technology gets glassy slag and solder, which after correction of the chemical composition can be used again for production of PCB.

The effects of boric acid and phosphoric acid on the compressive strength of glass-ionomer cements.

PubMed

Prentice, Leon H; Tyas, Martin J; Burrow, Michael F

2006-01-01

Both boric acid (H3BO3) and phosphoric acid (H3PO4) are components of dental cements, commonly incorporated into glass (as ingredients in the melt) and occasionally added to the powder or liquid components. This study investigated the effect of boric acid addition to an experimental glass-ionomer powder and the effect of phosphoric acid addition to a glass-ionomer liquid on the 24-h compressive strength. Boric acid powder was added in various concentrations to an experimental glass-ionomer powder and, separately, phosphoric acid was added to an experimental glass-ionomer liquid. Powders and liquids were dosed into capsules at various powder:liquid ratios and cements thus formed were assessed for 24-h compressive strength. Incorporation of boric acid in glass-ionomer powder resulted in a pronounced decrease (p < 0.05 at 1% boric acid) in compressive strength. Addition of phosphoric acid produced initially stronger cements (up to 13% increase at 1% phosphoric acid) before also declining. The incorporation of less than 2% w/w phosphoric acid in glass-ionomer liquids may improve cement strengths without compromising clinical usefulness. The incorporation of boric acid in glass-ionomer cements is contraindicated.

Dynamics of pH modification of an acidic protein bait used for tropical fruit flies (Diptera: Tephritidae).

PubMed

Heath, Robert R; Vazquez, Aime; Schnell, Elena Q; Villareal, Janett; Kendra, Paul E; Epsky, Nancy D

2009-12-01

Several species of Anastrepha and Bactrocera fruit flies (Diptera: Tephritidae) are captured in traps baited with the protein bait NuLure combined with borax (sodium tetraborate decahydrate) in an aqueous solution, typically 9% NuLure (vol:vol) with 3% borax (wt:vol). NuLure is an acid hydrolysate of corn and has an acidic pH. Addition of borax makes the solution more alkaline, and increase in alkalinity results in increase of ammonia release from the bait solution. This is a very dynamic system, with resultant pH affected by factors such as the amount of borax added, the pH of the water used for preparation, the age of the bait solution, and the development of microbial growth. Problems with borax include amount needed to increase alkalinity of NuLure solutions, which creates difficulties in disposing of spent bait in fruit fly trapping programs. Therefore, research was conducted to evaluate NaOH as an alternative method to increase alkalinity of NuLure solutions. Laboratory experiments compared effect of NaOH versus borax for pH modification on changes in pH and ammonia content of NuLure solutions over time. Although NuLure/NaOH solutions could be adjusted to a more alkaline pH than NuLure/borax solutions, borax plays a critical role in pH stability over time. However, the pH of NuLure/NaOH is stabilized when propylene glycol (10% vol:vol) was used to prepare the bait solution. The use of NaOH can provide an alternative to the use of borax to increase bait solution alkalinity.

LITERATURE REVIEW OF BORIC ACID SOLUBILITY DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crapse, K.; Kyser, E.

2011-09-22

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system replaces the current dilute nitric acid strip solution with 0.01 M boric acid. This literature study is performed to determine if there is a potential for boric acid to crystallize in the lines with emphasis on the transfer lines to the Defense Waste Processing Facility. This report focuses on the aqueous phase chemistry of boric acid under conditions relevant to MCU and SWPF. Operating and transfer conditions examined for the purpose ofmore » this review include temperatures between 13 C (McLeskey, 2008) and 45 C (Fondeur, 2007) and concentrations from 0 to 3M in nitric acid as well as exposure of small amounts of entrained boric acid in the organic phase to the sodium hydroxide caustic wash stream. Experiments were also conducted to observe any chemical reactions and off-gas generation that could occur when 0.01 M boric acid solution mixes with 3 M nitric acid solution and vice versa. Based on the low concentration (0.01M) of boric acid in the MCU/SWPF strip acid and the moderate operating temperatures (13 C to 45 C), it is unlikely that crystallization of boric acid will occur in the acid strip solution under process or transfer conditions. Mixing experiments of boric and nitric acid show no measurable gas generation (< 1 cc of gas per liter of solution) under similar process conditions.« less

Identification of boric acid as a novel chemoattractant and elucidation of its chemoreceptor in Ralstonia pseudosolanacearum Ps29.

PubMed

Hida, Akiko; Oku, Shota; Nakashimada, Yutaka; Tajima, Takahisa; Kato, Junichi

2017-08-17

Chemotaxis enables bacteria to move toward more favorable environmental conditions. We observed chemotaxis toward boric acid by Ralstonia pseudosolanacearum Ps29. At higher concentrations, the chemotactic response of R. pseudosolanacearum toward boric acid was comparable to or higher than that toward L-malate, indicating that boric acid is a strong attractant for R. pseudosolanacearum. Chemotaxis assays under different pH conditions suggested that R. pseudosolanacearum recognizes B(OH) 3 (or B(OH 3 ) + B(OH) 4 - ) but not B(OH) 4 - alone. Our previous study revealed that R. pseudosolanacearum Ps29 harbors homologs of all 22R. pseudosolanacearum GMI1000 mcp genes. Screening of 22 mcp single-deletion mutants identified the RS_RS17100 homolog as the boric acid chemoreceptor, which was designated McpB. The McpB ligand-binding domain (LBD) was purified in order to characterize its binding to boric acid. Using isothermal titration calorimetry, we demonstrated that boric acid binds directly to the McpB LBD with a K D (dissociation constant) of 5.4 µM. Analytical ultracentrifugation studies revealed that the McpB LBD is present as a dimer that recognizes one boric acid molecule.

A case report of massive acute boric acid poisoning.

PubMed

Corradi, Francesco; Brusasco, Claudia; Palermo, Salvatore; Belvederi, Giulio

2010-02-01

Boric acid comes as colourless, odourless white powder and, if ingested, has potential fatal effects including metabolic acidosis, acute renal failure and shock. An 82-year-old male was brought to the emergency room 3 h after unintentional ingestion of a large amount of boric acid. Clinical course was monitored by collecting data at admittance, 12 h after admission, every 24 h for 5 days and again 1 week after admission. During the first 132 h, serum and urinary concentrations of boric acid were measured. Serum boric acid levels decreased from 1800 to 530 microg/ml after haemodialysis and from 530 to 30 microg/ml during the forced diuresis period. During dialysis, boric acid clearance averaged 235 ml/min with an extraction ratio of 70%. The overall patient's condition steadily improved over 84 h after admission. In conclusion, early treatment with forced diuresis and haemodialysis may be considered for boric acid poisoning, even if signs of renal dysfunction are not apparent, to prevent severe renal damage and its complications.

Effect of boric acid mass transfer on the accumulation thereof in a fuel core under emergency modes at NPPs with WMR

NASA Astrophysics Data System (ADS)

Morozov, A. V.; Sorokin, A. P.; Ragulin, S. V.; Pityk, A. V.; Sahipgareev, A. R.; Soshkina, A. S.; Shlepkin, A. S.

2017-07-01

Boric acid mass transfer processes in the reactor facilities with WMR are considered for the case of an emergency with breaking of the main circulation pipeline (MCP) and the operation of the passive safety systems, such as first-, second-, and third-stage accumulator tank systems, and a passive heat removal system (PHRS). Calculation results are presented for a change in the boric acid concentration in the fuel core (FC) of a water-moderated reactor (WMR) in the case of an emergency process. The calculations have been performed for different values of drop entrainment of boric acid from the reactor (0, 0.2, 2%). A substantial excess of the maximum concentration of boric acid has been found to occur 24 hours after an emergency event with a break of MCP. It is shown that increasing the droplet entrainment of boric acid causes the crystallization and accumulation thereof in the FC to become slower. The mass of boric acid deposits on the elements of internals is determined depending on the values of drop entrainment. These results allow one to draw a conclusion concerning the possibility of accumulation and crystallization of boric acid in the FC, because the latter event could lead to a blocking of the flow cross section and disturbance in the heat removal from fuel elements. A review of available literature data concerning the thermal properties of boric acid solution (density, viscosity, thermal conductivity) is presented. It is found that the available data are of quite a general character, but it does not cover the entire range of parameters (temperature, pressure, acid concentrations) inherent in a possible emergency situation at nuclear power plants with WMR. It is demonstrated that experimental study of boric acid drop entrainment at the parameters inherent in the emergency mode of WMR operation, as well as the studies of boric acid thermal properties in a wide range of concentrations, are required.

The ototoxic effect of boric acid solutions applied into the middle ear of guinea pigs.

PubMed

Oztürkcan, Sedat; Dündar, Riza; Katilmis, Hüseyin; Ilknur, Ali Ekber; Aktaş, Sinem; Haciömeroğlu, Senem

2009-05-01

This study analyzed the ototoxic effects of boric acid solutions. Boric acid solutions have been used as otologic preparations for many years. Boric acid is commonly found in solutions prepared with alcohol or distilled water but can also be found in a powder form. These preparations are used for both their antiseptic and acidic qualities in external and middle ear infections. We investigated the ototoxic effect of boric acid solutions on guinea pigs. We are unaware of any similar, previously published study of this subject in English. The study was conducted on 28 young albino guinea pigs. Prior to application of the boric acid solution under general anesthesia, an Auditory Brainstem Response (ABRs) test was applied to the right ear of the guinea pigs. Following the test, a perforation was created on the tympanic membrane of the right ear of each guinea pig and small gelfoam pieces were inserted into the perforated area. Test solutions were administered to the middle ear for 10 days by means of a transcanal route. Fifteen days after inserting the gelfoams in all of the guinea pigs, we anasthesized the guinea pigs and removed the gelfoams from the perforated region of the ear and then performed an ABRs on each guinea pig. The ABRs were within the normal range before the applications. After the application, no significant changes were detected in the ABRs thresholds in neither the saline group nor the group administered boric acid and distilled water solution; however, significant changes were detected in the ABRs thresholds of the Gentamicine and boric acid and alcohol solution groups. We believe that a 4% boric acid solution prepared with distilled water can be a more reliable preparation than a 4% boric acid solution prepared with alcohol.

40 CFR 721.3032 - Boric acid (H3BO2), zinc salt.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Boric acid (H3BO2), zinc salt. 721... Substances § 721.3032 Boric acid (H3BO2), zinc salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as boric acid (H3BO2), zinc salt (PMN P-97-553...

40 CFR 721.3032 - Boric acid (H3BO2), zinc salt.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Boric acid (H3BO2), zinc salt. 721... Substances § 721.3032 Boric acid (H3BO2), zinc salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as boric acid (H3BO2), zinc salt (PMN P-97-553...

Spectrophotometric determination of boric acid in boron powder with curcumin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grotheer, E.W.

1979-12-01

A rapid and accurate method was needed to determine trace amounts of boric acid for quality control and specification testing of elemental boron. The reaction between boric acid and curcumin occurs at a measurable rate only when the curcumin molecule is protonated. Protonation takes place at the carbonyl groups in the presence of a strong acid and occurs completely and rapidly when sulfuric acid is added to a solution of curcumin in acetic acid. Spectrophotometric measurements were made. The extraction of boric acid from boron powder was found to be complete within 2h when either water or the diol solutionmore » was used. Whatman No. 40 cr 42 filter paper was used to obtain diol samples free of boron particles. The extraction efficiency of 2-ethyl-1,3-hexanediol was evaluated by adding 1 ml of 500 ppM aqueous boric acid and 1 drop of 10% NaOH to accurately weighed samples of boron powder. The water then was evaporated at room temperature and the samples were extracted with diol solution. The data obtained are included. The extraction efficiency also was evaluated by determining the boric acid content of boron which had been recovered from a previous extraction and boric acid determination. The determination of boric acid using curcumin is unaffected by the presence of other compounds, except for fluoride and nitrate ions. 2 tables. (DP)« less

Mechanism of permeability-enhancing effect of EDTA and boric acid on the corneal penetration of 4-[1-hydroxy-1-methylethyl]-2-propyl-1-[4-[2-[tetrazole-5-yl]phenyl]phenyl] methylimidazole-5-carboxylic acid monohydrate (CS-088).

PubMed

Kikuchi, Takayuki; Suzuki, Masahiko; Kusai, Akira; Iseki, Ken; Sasaki, Hitoshi; Nakashima, Kenichiro

2005-08-11

This study was conducted to clarify the penetration properties of 4-[1-hydroxy-1-methylethyl]-2-propyl-1-[4-[2-[tetrazole-5-yl]phenyl]phenyl]methylimidazole-5-carboxylic acid monohydrate (CS-088), an ophthalmic agent, and the mechanism of the permeability-enhancing effect of EDTA and boric acid (EDTA/boric acid) on the corneal penetration of CS-088. In the absence of additives, corneal permeability decreased with increasing concentration of CS-088 as CS-088 monomers self-associate to form dimers. Presence of EDTA/boric acid caused no significant changes in the physicochemical properties of CS-088, the apparent partition coefficient or the mean particle size of CS-088. EDTA/boric acid induced only a slight change in the zeta potential of liposomes used as a model of the biological membrane. On the other hand, EDTA/boric acid significantly increased membrane fluidity of liposomes, whereas other buffering agents tested did not. This effect was synergistic and concentration-dependent for both EDTA and boric acid as was observed in in vitro corneal penetration of CS-088. In accordance with the result, the rate of CS-088 permeation into the liposomes significantly increased by the addition of EDTA/boric acid. Therefore, it was demonstrated that EDTA/boric acid promotes corneal penetration of CS-088 through the transcellular pathway by increasing membrane fluidity. Conversely, other buffering agents decreased corneal permeability of CS-088 by inducing further self-association of CS-088 aggregates.

The effect of boric acid on acethylcholine, bethanechol and potasssium-evoked responses on ileum of rat.

PubMed

Ince, S; Turkmen, R; Yavuz, H

2011-01-01

1 The aim of this study was to clarify the effect of boric acid on contractions of rat isolated ileum. 2 Contractile responses expressed as Emax and pD2 for acetylcholine (10(-3)-10(-8) m, Ach), bethanechol (10(-3)-10(-8) m) and potassium (10-80 × 10(-3) m, KCl) were determined in the absence and presence of boric acid (10(-3); 5 × 10(-4); 10(-4) m). 3 The contractile response to Ach in the presence of verapamil (10(-6) or 10(-8) m) or in calcium-free Tyrode's solution was also determined in the absence and presence of boric acid. 4 Boric acid did not affect the contractile response to Ach, bethanechol or KCl. Single or cumulative treatment of boric acid did not affect ileum muscle contraction evoked by KCl. The atropine-resistant component of Ach-induced contraction and 4-diphenyl-acetoxy-N-methyl-piperidine methiodide-resistant component of bethanechol-induced contraction were not inhibited by boric acid (10(-3) m). The contractile response to Ach was reduced in calcium-free Tyrode's solution, and the contractile response was not affected by (10(-8) m). The addition of boric acid (10(-3) m) in combination with verapamil (10(-8) m) did not significantly affect the contractile response to Ach. 5 In conclusion, boric acid does not affect contractions induced by Ach, bethanechol or potassium in rat isolated ileum. © 2011 Blackwell Publishing Ltd.

40 CFR 721.3031 - Boric acid (H3BO3), zinc salt (2=3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Boric acid (H3BO3), zinc salt (2=3... Substances § 721.3031 Boric acid (H3BO3), zinc salt (2=3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as boric acid (H3BO3), zinc salt (2=3) (PMN P...

40 CFR 721.3031 - Boric acid (H3BO3), zinc salt (2=3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Boric acid (H3BO3), zinc salt (2=3... Substances § 721.3031 Boric acid (H3BO3), zinc salt (2=3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as boric acid (H3BO3), zinc salt (2=3) (PMN P...

Effect of mass transfer processes on accumulation and crystallization of boric acid in WWER core in emergency cases

NASA Astrophysics Data System (ADS)

Morozov, A. V.; Pityk, A. V.; Ragulin, S. V.; Sahipgareev, A. R.; Soshkina, A. S.; Shlepkin, A. S.

2017-09-01

In this paper the processes of boric acid mass transfer in a WWER-TOI nuclear reactor in case of the accidents with main coolant circuit rupture and operation of passive safety systems (the hydro accumulators systems of the first, second and third stages, as well as the passive heat removal system) are considered. The results of the calculation of changes in the boric acid solution concentration in the core for the WWER emergency mode are presented. According to the results of the calculation a significant excess of the ultimate concentration of boric acid in accidents with main coolant circuit rupture after 43 hours of emergency mode is observed. The positive influence of the boric acid droplet entrainment on the processes of its crystallization and accumulation in the core is shown. The mass of boric acid deposits on the internals is determined. The received results allow concluding that the accumulation and crystallization of boric acid in the core may lead to blocking the flow cross section and to deterioration of heat removal from fuel rods. The necessity of an experimental studies of the processes of boric acid drop entrainment under conditions specific to the WWER emergency modes is shown.

Boric Acid Induced Transient Cross-Links in Lactose-Modified Chitosan (Chitlac).

PubMed

Sacco, Pasquale; Furlani, Franco; Cok, Michela; Travan, Andrea; Borgogna, Massimiliano; Marsich, Eleonora; Paoletti, Sergio; Donati, Ivan

2017-12-11

The present paper explores the effect of boric acid on Chitlac, a lactose-modified chitosan which had previously shown interesting biological and physical-chemical features. The herewith-reported experimental evidences demonstrated that boric acid binds to Chitlac, producing conformational and association effects on the chitosan derivative. The thermodynamics of boric acid binding to Chitlac was explored by means of 11 B NMR, circular dichroism (CD), and UV-vis spectroscopy, while macromolecular effects were investigated by means of viscometry and dynamic light scattering (DLS). The experimental results revealed a chain-chain association when limited amounts of boric acid were added to Chitlac. However, upon exceeding a critical boric acid limit dependent on the polysaccharide concentration, the soluble aggregates disentangle. The rheological behavior of Chitlac upon treatment with boric acid was explored showing a dilatant behavior in conditions of steady flow. An uncommonly high dependence in the scaling law between the zero-shear viscosity and the concentration of Chitlac was found, i.e., η 0 ∝ C CTL 5.8 , pointing to interesting potential implications of the present system in biomaterials development.

In situ synthesis of twelve dialkyltartrate-boric acid complexes and two polyols-boric acid complexes and their applications as chiral ion-pair selectors in nonaqueous capillary electrophoresis.

PubMed

Wang, Li-Juan; Yang, Juan; Yang, Geng-Liang; Chen, Xing-Guo

2012-07-27

In this paper, twelve dialkyltartrate-boric acid complexes and two polyols-boric acid complexes were in situ synthesized by the reaction of different dialkyltartrates or polyols with boric acid in methanol containing triethylamine. All of the twelve dialkyltartrate-boric acid complexes were found to have relatively good chiral separation performance in nonaqueous capillary electrophoresis (NACE). Their chiral recognition effects in terms of both enantioselectivity (α) and resolution (R(s)) were similar when the number of carbon atoms was below six in the alkyl group of alcohol moiety. The dialkyltartrates containing alkyl groups of different structures but the same number of carbon atoms, i.e. one of straight chain and one of branched chain, also provided similar chiral recognition effects. Furthermore, it was demonstrated for the first time that two methanol insoluble polyols, D-mannitol and D-sorbitol, could react with boric acid to prepare chiral ion-pair selectors using methanol as the solvent medium. Copyright © 2012 Elsevier B.V. All rights reserved.

Lubrication from mixture of boric acid with oils and greases

DOEpatents

Erdemir, Ali

1995-01-01

Lubricating compositions including crystalline boric acid and a base lubricant selected from oils, greases and the like. The lubricity of conventional oils and greases can also be improved by adding concentrates of boric acid.

Analyzing the environmental impacts of laptop enclosures ...

EPA Pesticide Factsheets

The market growth of consumer electronics makes it essential for industries and policy-makers to work together to develop sustainable products. The objective of this study is to better understand how to promote environmentally sustainable consumer electronics by examining the use of various materials in laptop enclosures (excluding mounting hardware, internal components, and insulation) using screening-level life cycle assessment. The baseline material, is a fossil plastic blend of polycarbonate-acrylonitrile butadiene styrene. Alternative materials include polylactic acid, bamboo, aluminum, and various combinations of these materials known to be currently used or being considered for use in laptops. The flame retardants considered in this study are bisphenol A bis(diphenyl phosphate), triphenyl phosphate, 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide, and borax-boric acid-phosphorous acid. The Tool for the Reduction and Assessment of Chemical and other environmental Impacts v2.1 was used for the assessment of impacts related to climate change, human and ecological health, and resource use. The assessment demonstrates that plastics, relative to the other materials, are currently some of the better performing materials in terms of having the lowest potential environmental impact for a greater number of impact categories based on product life cycle models developed in this study. For fossil plastics, the material performance increases with increasing post-con

Hybrid films of chitosan, cellulose nanofibrils and boric acid: Flame retardancy, optical and thermo-mechanical properties.

PubMed

Uddin, Khan M A; Ago, Mariko; Rojas, Orlando J

2017-12-01

Chitosan (CS), cellulose nanofibrils (CNF) and boric acid, the latter of which was used as flame retardant, were combined in transparent, hybrid films that were produced by solvent casting. The flammability and the thermal stability of the films were studied with respect to the loading of the inorganic component. Chitosan films displayed fire retardancy properties, which were enhanced in the presence of boric acid. CNF films, in contrast to those from chitosan, were readily flammable; however, when combined with boric acid (30w%), they became self-extinguishing. Most remarkably, bicomponent films comprising CNF and chitosan, displayed better fire retardancy than that of neat CS films. Moreover, boric acid improved the thermal stability of the bicomponent films. The tensile strength and Young's modulus of CS, CNF and CS-CNF films improved at intermediate boric acid addition, although a negative effect on elongation was observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental study on the estrogen-like effect of boric Acid.

PubMed

Wang, Yadong; Zhao, Yingzheng; Chen, Xiaoyu

2008-02-01

There are now considerable evidences that boric acid has reproductive and developmental toxicity, but it is uncertain whether such toxicity is caused by estrogen-like effect. Our objective is to determine the estrogen-like effect of boric acid. Proliferation assay of MCF-7 human breast cancer cells, uterotrophic assay, measure assay of the estradiol (E2), proliferation assay of mucous membrane cells, and assay of estrogen receptor were conducted in this study. Boric acid could increase the weight of uterus of ovariectomized SD rats and the height of epithelium cells of mucous membrane, enhance the expression of the proliferating cell nucleus antigen, and reduce the density of estrogen receptors. However, boric acid could not affect the level of estradiol in serum and stimulate the proliferation of MCF-7 human breast cancer cells. In this study, boric acid exhibited the estrogen-like effect in vivo.

Non-intercalative, deoxyribose binding of boric acid to calf thymus DNA.

PubMed

Ozdemir, Ayse; Gursaclı, Refiye Tekiner; Tekinay, Turgay

2014-05-01

The present study characterizes the effects of the boric acid binding on calf thymus DNA (ct-DNA) by spectroscopic and calorimetric methods. UV-Vis absorbance spectroscopy, circular dichroism (CD) spectroscopy, transmission electron microscopy (TEM), isothermal titration calorimetry (ITC), and Fourier transform infrared (FT-IR) spectroscopy were employed to characterize binding properties. Changes in the secondary structure of ct-DNA were determined by CD spectroscopy. Sizes and morphologies of boric acid-DNA complexes were determined by transmission electron microscopy (TEM). The kinetics of boric acid binding to calf thymus DNA (ct-DNA) was investigated by isothermal titration calorimetry (ITC). ITC results revealed that boric acid exhibits a moderate affinity to ct-DNA with a binding constant (K a) of 9.54 × 10(4) M(-1). FT-IR results revealed that boric acid binds to the deoxyribose sugar of DNA without disrupting the B-conformation at tested concentrations.

Efficacy of Boric Acid as a Treatment of Choice for Chronic Suppurative Otitis Media and Its Ototoxicity.

PubMed

Adriztina, Indri; Adenin, Linda Irwani; Lubis, Yuliani Mardiati

2018-01-01

Chronic suppurative otitis media (CSOM) is one of the most common chronic infectious diseases worldwide, especially affecting children. The patients or the parents of the affected children are often worried about the cost of medical visits, prescription medicines, or inconsistently effective medication. The complications of CSOM have been greatly reduced because of the development of antibiotics; however, the irrational use of antibiotics has led to the emergence of organisms resistant to the commonly used drugs. Owing to the increase in antibiotic resistance, the development of new treatments that will efficiently eradicate infectious microorganisms has become imperative. Boric acid solutions are effective in the treatment of CSOM because of their acidic effect. Various databases, such as the PubMed, The Cochrane Library, and SciELO, were searched for references related to the efficacy of boric acid in the treatment of mucosal CSOM, as well as its ototoxicity. The search revealed that boric acid is relatively effective in treating CSOM, especially at a high concentration. Boric acid in distilled water was found safe in animal studies. However, the ototoxicity of boric acid concentrations higher than 4% needs further evaluation, considering the effectivity of boric acid at high concentrations.

Efficacy of Boric Acid as a Treatment of Choice for Chronic Suppurative Otitis Media and Its Ototoxicity

PubMed Central

Adenin, Linda Irwani; Lubis, Yuliani Mardiati

2018-01-01

Chronic suppurative otitis media (CSOM) is one of the most common chronic infectious diseases worldwide, especially affecting children. The patients or the parents of the affected children are often worried about the cost of medical visits, prescription medicines, or inconsistently effective medication. The complications of CSOM have been greatly reduced because of the development of antibiotics; however, the irrational use of antibiotics has led to the emergence of organisms resistant to the commonly used drugs. Owing to the increase in antibiotic resistance, the development of new treatments that will efficiently eradicate infectious microorganisms has become imperative. Boric acid solutions are effective in the treatment of CSOM because of their acidic effect. Various databases, such as the PubMed, The Cochrane Library, and SciELO, were searched for references related to the efficacy of boric acid in the treatment of mucosal CSOM, as well as its ototoxicity. The search revealed that boric acid is relatively effective in treating CSOM, especially at a high concentration. Boric acid in distilled water was found safe in animal studies. However, the ototoxicity of boric acid concentrations higher than 4% needs further evaluation, considering the effectivity of boric acid at high concentrations. PMID:29383205

Lubrication from mixture of boric acid with oils and greases

DOEpatents

Erdemir, A.

1995-07-11

Lubricating compositions are disclosed including crystalline boric acid and a base lubricant selected from oils, greases and the like. The lubricity of conventional oils and greases can also be improved by adding concentrates of boric acid.

The Acid-Base Titration of a Very Weak Acid: Boric Acid

ERIC Educational Resources Information Center

Celeste, M.; Azevedo, C.; Cavaleiro, Ana M. V.

2012-01-01

A laboratory experiment based on the titration of boric acid with strong base in the presence of d-mannitol is described. Boric acid is a very weak acid and direct titration with NaOH is not possible. An auxiliary reagent that contributes to the release of protons in a known stoichiometry facilitates the acid-base titration. Students obtain the…

40 CFR 721.1730 - Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1730 Section 721.1730 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric...

40 CFR 721.1730 - Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1730 Section 721.1730 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric...

40 CFR 721.1731 - Poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2012 CFR

2012-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1731 Section 721.1731 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric...

40 CFR 721.1731 - Poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2010 CFR

2010-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1731 Section 721.1731 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric...

40 CFR 721.1731 - Poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2011 CFR

2011-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1731 Section 721.1731 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric...

40 CFR 721.1731 - Poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2013 CFR

2013-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1731 Section 721.1731 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric...

40 CFR 721.1730 - Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2012 CFR

2012-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1730 Section 721.1730 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric...

40 CFR 721.1731 - Poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-hydroxy, ester with boric acid (H3BO3). 721.1731 Section 721.1731 Protection of Environment ENVIRONMENTAL..., ester with boric acid (H3BO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-methyl-ω-hydroxy, ester with boric...

Protective effect of boric acid against carbon tetrachloride-induced hepatotoxicity in mice.

PubMed

Ince, Sinan; Keles, Hikmet; Erdogan, Metin; Hazman, Omer; Kucukkurt, Ismail

2012-07-01

The protective effect of boric acid against liver damage was evaluated by its attenuation of carbon tetrachloride (CCl(4))-induced hepatotoxicity in mice. Male albino mice were treated intraperitoneally (i.p.) with boric acid (50, 100, and 200 mg/kg) or silymarin daily for 7 days and received 0.2% CCl(4) in olive oil (10 mL/kg, i.p.) on day 7. Results showed that administration of boric acid significantly reduced the elevation in serum levels of aspartate aminotransferase, alkaline phosphatase, alanine aminotransferase, and the level of malondialdehyde in the liver that were induced by CCl(4) in mice. Boric acid treatment significantly increased glutathione content, as well as the activities of superoxide dismutase and catalase in the liver. Boric acid treatment improved the catalytic activity of cytochrome P450 2E1 and maintained activation of nuclear factor kappa light-chain enhancer of activated B cell gene expression, with no effect on inducible nitric oxide synthase gene expression in the livers of mice. Histopathologically, clear decreases in the severity of CCl(4)-induced lesions were observed, particularly at high boric acid concentrations. Results suggest that boric acid exhibits potent hepatoprotective effects on CCl(4)-induced liver damage in mice, likely the result of both the increase in antioxidant-defense system activity and the inhibition of lipid peroxidation.

Experimental Study and Reactive Transport Modeling of Boric Acid Leaching of Concrete

NASA Astrophysics Data System (ADS)

Pabalan, R. T.; Chiang, K.-T. K.

2013-07-01

Borated water leakage through spent fuel pools (SFPs) at pressurized water reactors is a concern because it could cause corrosion of reinforcement steel in the concrete structure, compromise the integrity of the structure, or cause unmonitored releases of contaminated water to the environment. Experimental data indicate that pH is a critical parameter that determines the corrosion susceptibility of rebar in borated water and the degree of concrete degradation by boric acid leaching. In this study, reactive transport modeling of concrete leaching by borated water was performed to provide information on the solution pH in the concrete crack or matrix and the degree of concrete degradation at different locations of an SFP concrete structure exposed to borated water. Simulations up to 100 years were performed using different boric acid concentrations, crack apertures, and solution flow rates. Concrete cylinders were immersed in boric acid solutions for several months and the mineralogical changes and boric acid penetration in the concrete cylinder were evaluated as a function of time. The depths of concrete leaching by boric acid solution derived from the reactive transport simulations were compared with the measured boric acid penetration depth.

PRELIMINARY EVALUATION OF DWPF IMPACTS OF BORIC ACID USE IN CESIUM STRIP FOR SWPF AND MCU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M.

2010-09-28

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix,more » or the new suppressor, guanidine). Boric acid additions may lead to increased hydrogen generation during the SRAT and SME cycles as well as change the rheological properties of the feed. The boron in the strip effluent will impact glass composition and could require each SME batch to be trimmed with boric acid to account for any changes in the boron from strip effluent additions. Addition of boron with the strip effluent will require changes in the frit composition and could lead to changes in melt behavior. The severity of the impacts from the boric acid additions is dependent on the amount of boric acid added by the strip effluent. The use of 0.1M or higher concentrations of boric acid in the strip effluent was found to significantly impact DWPF operations while the impact of 0.01M boric acid is expected to be relatively minor. Experimental testing is required to resolve the issues identified during the preliminary evaluation. The issues to be addressed by the testing are: (1) Impact on SRAT acid addition and hydrogen generation; (2) Impact on melter feed rheology; (3) Impact on glass composition control; (4) Impact on frit production; and (5) Impact on melter offgas. A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix, or the new suppressor, guanidine). Experimental testing with the improved solvent is required to determine the impact of any changes in the entrained solvent on DWPF processing.« less

The antioxidant and antiapoptotic effect of boric acid on hepatoxicity in chronic alcohol-fed rats.

PubMed

Sogut, Ibrahim; Paltun, Sıla Ozlem; Tuncdemir, Matem; Ersoz, Melike; Hurdag, Canan

2018-04-01

The harmful use of alcohol is a worldwide problem involving all ages. This study aims to investigate chronic alcohol exposure related hepatotoxicity on the rat liver and possible hepatoprotective effects of boric acid. Rats were separated into 4 different groups: control, ethanol, ethanol+boric acid, and boric acid. We measured (i) malondialdehyde (MDA), total sialic acid (TSA), superoxide dismutase (SOD), catalase (CAT), and glutathione peroxidase (GPx) levels, which are known to be the markers of alcohol damage; and also (ii) caspase-3, tumor necrosis factor-alpha (TNF-α), and the terminal deoxynucleotidyl transferase dUTP nick-end labeling (TUNEL) as the markers of apoptosis. In the ethanol group, MDA, TSA, and TNF-α levels increased whereas SOD and CAT levels decreased compared with the control group. Ethanol+boric acid group MDA, TSA, caspase-3, and TNF-α levels decreased whereas SOD and CAT levels increased compared with the ethanol group. Using histopathological evaluation of light microscope images, immunohistochemical caspase-3 and TNF-α activity in the ethanol+boric acid group were shown to be decreased compared with that in the ethanol group. Our results revealed that ethanol is capable of triggering oxidative stress and apoptosis in the rat liver. We propose that boric acid is an effective compound in protecting the rat liver against ethanol.

High production of D-tagatose by the addition of boric acid.

PubMed

Lim, Byung-Chul; Kim, Hye-Jung; Oh, Deok-Kun

2007-01-01

An L-arabinose isomerase mutant enzyme from Geobacillus thermodenitrificans was used to catalyze the isomerization of D-galactose to D-tagatose with boric acid. Maximum production of D-tagatose occurred at pH 8.5-9.0, 60 degrees C, and 0.4 molar ratio of boric acid to D-galactose, and the production increased with increasing enzyme concentration. Under the optimum conditions, the enzyme (10.8 units/mL) converted 300 g/L D-galactose to 230 g/L D-tagatose for 20 h with a yield of 77% (w/w); the production and conversion yield with boric acid were 1.5-fold and 24% higher than without boric acid, respectively. In 24 h, the enzyme produced 370 g/L D-tagatose from 500 g/L D-galactose with boric acid, corresponding to a conversion yield of 74% (w/w) and a production rate of 15.4 g/L.h. The production and yield of D-tagatose obtained in this study are unprecedented.

Influence of boric acid (H3BO3) concentration on the physical properties of electrochemical deposited nickel (Ni) nanowires

NASA Astrophysics Data System (ADS)

Kananathan, J.; Sofiah, A. G. N.; Samykano, M.; Ulakanathan, S.; Lah, N. A. C.; Harun, W. S. W.; Sudhakar, K.; Kadirgama, K.; Ngui, W. K.; Siregar, J. P.

2017-10-01

Authors have investigated the influence of the stabilizer (Boric Acid) concentration during the template-assisted electrochemical deposition of Nickel (Ni) nanowires in Anodic Alumina Oxide (AAO) templates. The synthesis was performed using Ni Sulfate Hexahydrate (NiSO4.6H2O) as metal salts and Boric Acid (H3BO3) as a stabilizer. The mixture of both solutions creates electrolyte and utilized for the electrochemical deposition of Ni nanowires. During the experiment, the boric acid concentration varied between 5 g/L, 37.5 g/L and 60 g/L with a deposition temperature of 80 °C (constant). After the electrochemical deposition process, AAO templates were cleaned with distilled water before dissolution in Sodium Hydroxide (NaOH) solution to obtain the freestanding Ni nanowires. Physical properties of the synthesized Ni nanowires were analyzed using Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive Spectroscopy (EDX) and X-ray Diffraction (XRD). The physical properties of obtained Ni nanowires has eloborated by taking into account the effect of boric acid concentration on the surface morphology, growth length, elemental composition and crystal orientation crystal of the synthesized nickel nanowires. The finding exposes that the boric acid concentration does not influence all aspects in the physicals properties of the synthesized Ni nanowires. The boric acid concentration did not affect the surface texture and crystal orientation. However, shorter Ni nanowires obtained as the concentration of boric acid increased.

Extreme Activity of Drug Nanocrystals Coated with A Layer of Non-Covalent Polymers from Self-Assembled Boric Acid

NASA Astrophysics Data System (ADS)

Zhan, Honglei; Liang, Jun F.

2016-12-01

Non-covalent polymers have remarkable advantages over synthetic polymers for wide biomedical applications. In this study, non-covalent polymers from self-assembled boric acid were used as the capping reagent to replace synthetic polymers in drug crystallization. Under acidic pH, boric acid self-assembled on the surface of drug nanocrystals to form polymers with network-like structures held together by hydrogen bonds. Coating driven by boric acid self-assembly had negligible effects on drug crystallinity and structure but resulted in drug nanocrystals with excellent dispersion properties that aided in the formation of a more stable suspension. Boric acid coating improved drug stability dramatically by preventing drug molecules from undergoing water hydrolysis in a neutral environment. More importantly, the specific reactivity of orthoboric groups to diols in cell glycocalyx facilitated a rapid cross-membrane translocation of drug nanocrystals, leading to efficient intracellular drug delivery, especially on cancer cells with highly expressed sialic acids. Boric acid coated nanocrystals of camptothecin, an anticancer drug with poor aqueous solubility and stability, demonstrated extreme cytotoxic activity (IC50 < 5.0 μg/mL) to cancer cells compared to synthetic polymer coated CPT nanocrystals and free CPT. Surface coating using non-covalent polymers from self-assembled boric acid will have wide biomedical applications especially in biomaterials and drug delivery field.

Extreme Activity of Drug Nanocrystals Coated with A Layer of Non-Covalent Polymers from Self-Assembled Boric Acid.

PubMed

Zhan, Honglei; Liang, Jun F

2016-12-09

Non-covalent polymers have remarkable advantages over synthetic polymers for wide biomedical applications. In this study, non-covalent polymers from self-assembled boric acid were used as the capping reagent to replace synthetic polymers in drug crystallization. Under acidic pH, boric acid self-assembled on the surface of drug nanocrystals to form polymers with network-like structures held together by hydrogen bonds. Coating driven by boric acid self-assembly had negligible effects on drug crystallinity and structure but resulted in drug nanocrystals with excellent dispersion properties that aided in the formation of a more stable suspension. Boric acid coating improved drug stability dramatically by preventing drug molecules from undergoing water hydrolysis in a neutral environment. More importantly, the specific reactivity of orthoboric groups to diols in cell glycocalyx facilitated a rapid cross-membrane translocation of drug nanocrystals, leading to efficient intracellular drug delivery, especially on cancer cells with highly expressed sialic acids. Boric acid coated nanocrystals of camptothecin, an anticancer drug with poor aqueous solubility and stability, demonstrated extreme cytotoxic activity (IC 50  < 5.0 μg/mL) to cancer cells compared to synthetic polymer coated CPT nanocrystals and free CPT. Surface coating using non-covalent polymers from self-assembled boric acid will have wide biomedical applications especially in biomaterials and drug delivery field.

Extreme Activity of Drug Nanocrystals Coated with A Layer of Non-Covalent Polymers from Self-Assembled Boric Acid

PubMed Central

Zhan, Honglei; Liang, Jun F.

2016-01-01

Non-covalent polymers have remarkable advantages over synthetic polymers for wide biomedical applications. In this study, non-covalent polymers from self-assembled boric acid were used as the capping reagent to replace synthetic polymers in drug crystallization. Under acidic pH, boric acid self-assembled on the surface of drug nanocrystals to form polymers with network-like structures held together by hydrogen bonds. Coating driven by boric acid self-assembly had negligible effects on drug crystallinity and structure but resulted in drug nanocrystals with excellent dispersion properties that aided in the formation of a more stable suspension. Boric acid coating improved drug stability dramatically by preventing drug molecules from undergoing water hydrolysis in a neutral environment. More importantly, the specific reactivity of orthoboric groups to diols in cell glycocalyx facilitated a rapid cross-membrane translocation of drug nanocrystals, leading to efficient intracellular drug delivery, especially on cancer cells with highly expressed sialic acids. Boric acid coated nanocrystals of camptothecin, an anticancer drug with poor aqueous solubility and stability, demonstrated extreme cytotoxic activity (IC50 < 5.0 μg/mL) to cancer cells compared to synthetic polymer coated CPT nanocrystals and free CPT. Surface coating using non-covalent polymers from self-assembled boric acid will have wide biomedical applications especially in biomaterials and drug delivery field. PMID:27934922

Fast quantitative analysis of boric acid by gas chromatography-mass spectrometry coupled with a simple and selective derivatization reaction using triethanolamine.

PubMed

Zeng, Li-Min; Wang, Hao-Yang; Guo, Yin-Long

2010-03-01

A fast, selective, and sensitive GC-MS method has been developed and validated for the determination of boric acid in the drinking water by derivatization with triethanolamine. This analytic strategy successfully converts the inorganic, nonvolatile boric acid B(OH)(3) present in the drinking water to a volatile triethanolamine borate B(OCH(2)CH(2))(3)N in a quantitative manner, which facilitates the GC measurement. The SIM mode was applied in the analysis and showed high accuracy, specificity, and reproducibility, as well as reducing the matrix effect effectively. The calibration curve was obtained from 0.01 microg/mL to 10.0 microg/mL with a satisfactory correlation coefficient of 0.9988. The limit of detection for boric acid was 0.04 microg/L. Then the method was applied for detection of the amount of boric acid in bottled drinking water and the results are in accordance with the reported concentration value of boric acid. This study offers a perspective into the utility of GC-MS as an alternate quantitative tool for detection of B(OH)(3), even for detection of boron in various other samples by digesting the boron compounds to boric acid. Copyright 2010 American Society for Mass Spectrometry. Published by Elsevier Inc. All rights reserved.

Boric acid for recurrent vulvovaginal candidiasis: the clinical evidence.

PubMed

Iavazzo, Christos; Gkegkes, Ioannis D; Zarkada, Ioanna M; Falagas, Matthew E

2011-08-01

Recurrent vulvovaginal candidiasis (VVC) remains a challenge to manage in clinical practice. Recent epidemiologic studies indicate that non-albicans Candida spp. are more resistant to conventional antifungal treatment with azoles and are considered as causative pathogens of vulvovaginal candidiasis. We searched PubMed and Scopus for studies that reported clinical evidence on the intravaginal use of boric acid for vulvovaginal candidiasis. We identified 14 studies (2 randomized clinical trials [RCTs], 9 case series, and 4 case reports) as eligible for inclusion in this review. Boric acid was compared with nystatin, terconazole, flucytosine, itraconazole, clotrimazole, ketoconazole, fluconazole, buconazole, and miconazole; as monotherapy, boric acid was studied in 7 studies. The mycologic cure rates varied from 40% to 100% in patients treated with boric acid; 4 of the 9 included case series reported statistically significant outcomes regarding cure (both mycologic and clinical) rates. None of the included studies reported statistically significant differences in recurrence rates. Regarding the adverse effects caused by boric acid use, vaginal burning sensation (<10% of cases), water discharge during treatment, and vaginal erythema were identified in 7 studies. Our findings suggest that boric acid is a safe, alternative, economic option for women with recurrent and chronic symptoms of vaginitis when conventional treatment fails because of the involvement of non-albicans Candida spp. or azole-resistant strains.

Preparation and characterization of (10)B boric acid with high purity for nuclear industry.

PubMed

Zhang, Weijiang; Liu, Tianyu; Xu, Jiao

2016-01-01

Boric acid is often added into coolant as neutron capture agent for pressurized water reactor, whose amount is influenced by its abundance and purity. Therefore, the preparation of enriched (10)B boric acid with high purity is beneficial to nuclear industry. (10)B is also used in developing tumor-specific boronated drugs in boron neutron capture therapy. The boronated drug can be administered to patient intravenously, intratumorally, or deposited at tumor site in surgical excision. Thus, enriched (10)B boric acid is of practical significance in the field of medicine. Self-made boron trifluoride-methanol-complex solution was selected as one of the experimental reagents, and the preparation of (10)B acid was realized by one-step reaction for the complexes with water and calcium chloride. The determination of electrical conductivity in reaction process proves that the optimum reaction time was 16-20 h. Furthermore, the effect of reaction time, ratio of calcium chloride to complex as well as the amount of water on the purity and yield of boric acid was investigated. Finally, the optimum reaction time was 20 h, the optimal solid-liquid ratio (molar ratio) was 3:1, and the amount of water was 1 L of deionized water for each mol of the complex. H2O2 was added in the reaction process to remove Fe(2+). After recrystallization, IR spectra of (10)B boric acid was measured and compared with standard to verify the product of boric acid. The feasibility of the preparation method was determined by the detection of XRD of boric acid. To observe the morphology by polarizing microscope, crystal structure was obtained. The purity of the final product is 99.95 %, and the yield is 96.47 %. The ion concentration of boric acid accords with the national standard of high purity, which was determined by ICP.

Termite Resistance of MDF Panels Treated with Various Boron Compounds

PubMed Central

Usta, Mustafa; Ustaomer, Derya; Kartal, Saip Nami; Ondaral, Sedat

2009-01-01

In this study, the effects of various boron compounds on the termite resistance of MDF panels were evaluated. Either borax (BX), boric acid (BA), zinc borate (ZB), or sodium perborate tetrahydrate (SPT) were added to urea-formaldehyde (UF) resin at target contents of 1%, 1.5%, 2% and 2.5% based on dry fiber weight. The panels were then manufactured using 12% urea-formaldehyde resin and 1% NH4Cl. MDF samples from the panels were tested against the subterranean termites, Coptotermes formosanus Shiraki. Laboratory termite resistance tests showed that all samples containing boron compounds had greater resistance against termite attack compared to untreated MDF samples. At the second and third weeks of exposure, nearly 100% termite mortalities were recorded in all boron compound treated samples. The highest termite mortalities were determined in the samples with either BA or BX. Also, it was found that SPT showed notable performance on the termite mortality. As chemical loadings increased, termite mortalities increased, and at the same time the weight losses of the samples decreased. PMID:19582229

Chemically bonded phosphate ceramic sealant formulations for oil field applications

DOEpatents

Wagh, Arun S [Naperville, IL; Jeong, Seung-Young [Taejon, KR; McDaniel, Richard [Crest Hill, IL

2008-10-21

A sealant for an oil or geothermal well capable of setting within about 3 to about 6 hours at temperatures less than about 250.degree. F. for shallow wells less than about 10,000 feet and deep wells greater than about 10,000 feet having MgO present in the range of from about 9.9 to about 14.5%, KH.sub.2PO.sub.4 present in the range of from about 29.7 to about 27.2%, class C fly ash present in the range of from about 19.8 to about 36.3%, class F fly ash present in the range of from about 19.8 to about 0%, boric acid or borax present in the range of from about 0.39 to about 1.45%, and water present in the range of from about 20.3 to about 21.86% by weight of the sealant.A method of sealing wells is disclosed as are compositions for very high temperature wells is disclosed as is a composition for treating oil field wastes.

PERIODS OF VERTEBRAL COLUMN SENSITIVITY TO BORIC ACID TREATMENT IN CD-1 MICE IN UTERO

EPA Science Inventory

Periods of vertebral column sensitivity to boric acid treatment in CD-1 mice in utero.

Cherrington JW, Chernoff N.

Department of Toxicology, North Carolina State University, Raleigh, NC 27695, USA. jana_cherrington@hotmail.com

Boric acid (BA) has many uses as...

Effect of Boric Acid Versus Conventional Irrigation Solutions on the Bond Strength Between Fiber Post 
and Root Dentin.

PubMed

Culhaoglu, Ahmet Kursad; Özcan, Erdal; Kilicarslan, Mehmet Ali; Seker, Emre

2017-01-01

To compare the effect of boric acid solutions of different percentages to conventional irrigation solutions on the adhesive bond strength between fiber posts and radicular dentin surface with different cement types. One hundred fifteen extracted human incisors were endodontically instrumented to a length of 14-15 mm, and 12-mm post spaces were prepared with specific drills. Cylindrical fiber posts (Panavia Post) were luted with two different composite cements (Panavia F 2.0, Panavia SA) and cut into 1-mm-thick slices. These specimens were randomly allocated to 5 groups according to the irrigant applied: 1. control, no irrigant; 2. 10 ml of 2% chlorhexidine; 3. 10 ml of 5.25% NaOCl for 5 min and 10 ml of 17% EDTA for 3 min; 4. 10 ml of 5% boric acid solution at a temperature of 55°C for 60 s; 5. 10% boric acid solution, conditions as in group 4. Bond strength was determined using the push-out test. Microscopic assessment and SEM evaluations were performed in combination with push-out tests. The push-out bond strengths of cervical segments were significantly higher than for the middle and apical segments in all groups. The type of irrigation solution used significantly affected the bond strengths of the posts. The 10% boric acid solution and EDTA + NaOCl irrigation solutions provided the highest bond strengths (p < 0.005). SEM analysis showed that the dentin tubules were open and the smear layer was completely removed when EDTA/NaOCl and 10% boric acid were used as irrigation agents. Boric acid solutions, especially at a concentration of 10%, can be a viable alternative to the conventional irrigants used during endodontic treatment. The extent to which the 10% boric acid solution successfully removed the smear layer and the ease of rinsing boric acid from the root surface are advantageous.

Liquid Superlubricity of Polyethylene Glycol Aqueous Solution Achieved with Boric Acid Additive.

PubMed

Ge, Xiangyu; Li, Jinjin; Zhang, Chenhui; Luo, Jianbin

2018-03-27

Boric acid is a weak acid and has been used as a lubrication additive because of its special structure. In this study, we report that boric acid could achieve a robust superlubricity (μ < 0.01) as an additive in polyethylene glycol (PEG) aqueous solution at the Si 3 N 4 /SiO 2 interfaces. The superlow and steady friction coefficient of approximately 0.004-0.006 could be achieved with boric acid under neutral conditions (pH of approximately 6.4), which is different from the acidic conditions leading to superlubricity. The influence of various factors, including boric acid concentration, sliding speed, applied load, PEG molecular weight, and the volume of lubricant on the superlubricity, were investigated. The results reveal that the PEG aqueous solution with the boric acid additive could achieve superlubricity under a wide range of conditions. The surface composition analysis shows that the synergy effect between boric acid and PEG provides sufficient H + ions to realize the running-in process. Moreover, a composite tribochemical film composed of silica and ammonia-containing compounds were formed on the ball surface, contributing to the superlubricity. The film thickness calculation shows that superlubricity was achieved in a mixed lubrication region, and therefore, the superlubricity state was dominated by both the composite tribochemical film formed via the tribochemical reaction on the contact surfaces and the hydrodynamic lubricating film between the contact surfaces. Such a liquid superlubricity achieved under neutral conditions is of importance for both scientific understanding and engineering applications.

Effect of nano-silver and boric acid on extending the vase life of cut rose (Rosa hybrida L.).

PubMed

Hashemabadi, Davood; Liavali, Mahbanoo Hoseinzadeh; Kaviani, Behzad; Mousavi, Meysam; Keyghobadi, Saghi; Zahiri, Samaneh

2014-09-01

Silver nano-particles (2-5 nm diam.), as antimicrobial agent and boric acid, as ethylene production inhibitor are used for enhancing the quality and vase life of cut flowers. In the present study the effects of a preservative solution containing nano-silver and boric acid on some traits of cut rose (Rosa hybrida L. cv. Yellow Island) including vase life, ethylene production, dry weight percentage, chlorophyll content, flower opening index, beta-carotene of petals and the number of basal stem end bacteria were investigated. The results showed that the effect of nano-silver and boric acid as either solitary or in combination with each other were significant (p < or = 0.01) on vase life, ethylene production and beta-carotene pigment. The effect of nano-silver on the number of bacteria on the end of stem was significant (p < or = 0.01). The highest cut flower longevity (9.69 day) was obtained in pulse-treated flowers with 100 mg l(-1) boric acid. The least ethylene production (0.59 nl(-1) g(-1) h(-1)) was observed in cut rose treated with 100 mg l(-1) boric acid along with 5 mg l(-1) nano-silver. The lowest number of bacteria in the end of stem was calculated in cut flowers treated with the highest concentrations of boric acid (300 mg l(-1)) and nano-silver (20 mg l(-1)).

Ingested boric acid effect on the venom chemistry of Solenopsis invicta Buren (Hymenoptera: Formicidae)

USDA-ARS?s Scientific Manuscript database

During a field evaluation of a boric acid bait against the red imported fire ant, Solenopsis invicta Buren, it was observed that workers of intoxicated colonies produced stings with less toxic effects compared to workers from healthy colonies. In this study, the effect of boric acid on the levels o...

Utilization of natural indicators for borax identification in the Indonesian tofu

NASA Astrophysics Data System (ADS)

Purbaningtias, Tri Esti; Lestari, Intan Dwi; Wiyantoko, Bayu; Kurniawati, Puji; Sriadryani, Devi

2017-03-01

Borax has been found in food products i.e. on the Indonesian Tofu that is often consumed by people. Generally, the identification of borax in food products hard to do by the public. Indicators of natural materials will allow the public to identify the presence of borax in food easier. Qualitative test for borax on Indonesian Tofu showed purple cabbage and sappanwood are the effective natural indicators. The result of determining borax on Indonesian Tofu indicated natural indicator from purple cabbage had the smallest correction factor (with conventional indicators PP) about 4.8%. The results of the validation method for purple cabbage indicator in acid-base titration showed that the purple cabbage indicator is homogenous but unstable. The natural indicators of purple cabbage could not be used again after three days of extraction time based on the results of control chart.

Oral toxicity of abamectin, boric acid, fipronil, and hydramethylnon to laboratory colonies of Argentine ants (Hymenoptera: Formicidae).

PubMed

Hooper-Bui, L M; Rust, M K

2000-06-01

Comprehensive laboratory baiting studies with the 4 insecticides abamectin, boric acid, fipronil, and hydramethylnon were conducted against Argentine ant, Linepithema humile (Mayr). Serial dilutions of each insecticide prepared in a 25% sucrose solution were provided for 24 h or 14 d to groups of workers and queens. Sucrose-water baits containing 1 x 10(-5)% fipronil and 0.1% hydramethylnon provided complete mortality of L. humile workers baited for 24 h. Baits containing 1 x 10(-4) and 1 x 10(-5)% fipronil provided 100% kill of queens. In the continuous baiting, 0.5% boric acid, 1 x 10(-6)% fipronil, and 0.025% hydramethylnon provided 100% mortality of workers. The queens and workers provided baits containing 1 x 10(-5)% fipronil and 0.5% boric acid all died within 14 d. Low concentrations of fipronil and boric acid in sucrose may be promising candidates for Argentine ant control.

40 CFR 721.3032 - Boric acid (H3BO2), zinc salt.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Boric acid (H3BO2), zinc salt. 721.3032 Section 721.3032 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3032 Boric acid (H3BO2),...

40 CFR 721.3032 - Boric acid (H3BO2), zinc salt.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Boric acid (H3BO2), zinc salt. 721.3032 Section 721.3032 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3032 Boric acid (H3BO2),...

40 CFR 721.3032 - Boric acid (H3BO2), zinc salt.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Boric acid (H3BO2), zinc salt. 721.3032 Section 721.3032 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3032 Boric acid (H3BO2),...

Complexation of Nickel Ions by Boric Acid or (Poly)borates.

PubMed

Graff, Anais; Barrez, Etienne; Baranek, Philippe; Bachet, Martin; Bénézeth, Pascale

2017-01-01

An experiment based on electrochemical reactions and pH monitoring was performed in which nickel ions were gradually formed by oxidation of a nickel metal electrode in a solution of boric acid. Based on the experimental results and aqueous speciation modeling, the evolution of pH showed the existence of significant nickel-boron complexation. A triborate nickel complex was postulated at high boric acid concentrations when polyborates are present, and the equilibrium constants were determined at 25, 50 and 70 °C. The calculated enthalpy and entropy at 25 °C for the formation of the complex from boric acid and Ni 2+ ions are respectively equal to (65.6 ± 3.1) kJ·mol -1 and (0.5 ± 11.1) J·K -1 ·mol -1 . The results of this study suggest that complexation of nickel ions by borates can significantly enhance the solubility of nickel metal and nickel oxide depending on the concentration of boric acid and pH. First principles calculations were investigated and tend to show that the complex is thermodynamically stable and the nickel cation in solution should interact more strongly with the [Formula: see text] than with boric acid.

40 CFR 721.1729 - Boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Boric acid (H3BO3), mixed esters with... acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol mono Me ether... identified as boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

40 CFR 721.1729 - Boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Boric acid (H3BO3), mixed esters with... acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol mono Me ether... identified as boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

40 CFR 721.1729 - Boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Boric acid (H3BO3), mixed esters with... acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol mono Me ether... identified as boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

40 CFR 721.1729 - Boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Boric acid (H3BO3), mixed esters with... acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol mono Me ether... identified as boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

40 CFR 721.1729 - Boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Boric acid (H3BO3), mixed esters with... acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol mono Me ether... identified as boric acid (H3BO3), mixed esters with polyethylene glycol mono-Bu ether and polyethylene glycol...

Effects of boron derivatives on extracellular matrix formation.

PubMed

Benderdour, M; Van Bui, T; Hess, K; Dicko, A; Belleville, F; Dousset, B

2000-10-01

Boric acid solution (3%) dramatically improves wound healing through action on the extracellular matrix, a finding that has been obtained in vitro. Consequently, investigations are presently underway to produce boronated compounds having a therapeutical effectiveness similar to that of boric acid. On the basis of experimental results obtained with boric acid, we examined the effects of boron derivatives on extracellular matrix formation and degradation and analyzed their potential toxicity by using two biological models (chick embryo cartilage and human fibroblasts). The four boron derivatives tested in this study (triethanolamine borate; N-diethyl-phosphoramidate-propylboronique acid; 2,2 dimethylhexyl-1,3-propanediol-aminopropylboronate and 1,2 propanediol-aminopropylboronate) mimicked the effects of boric acid. They induced a decrease of intracellular concentrations in extracellular matrix macromolecules (proteoglycans, proteins)-associated with an increase of their release in culture medium and stimulated the activity of intra- and extracellular proteases. Similarly to boric acid, these actions occurred after exposure of the cells to concentrations of all boron derivatives without apparent toxic effects. The compounds were found to be more toxic than boric acid itself when concentrations were calculated according to their molecular weight. Nevertheless, these in vitro preliminary results demonstrate effects of boron derivatives that may be of therapeutic benefit in wound repair.

40 CFR 721.3031 - Boric acid (H3BO3), zinc salt (2=3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Boric acid (H3BO3), zinc salt (2=3). 721.3031 Section 721.3031 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3031 Boric acid (H3BO...

40 CFR 721.3031 - Boric acid (H3BO3), zinc salt (2=3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Boric acid (H3BO3), zinc salt (2=3). 721.3031 Section 721.3031 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3031 Boric acid (H3BO...

40 CFR 721.3031 - Boric acid (H3BO3), zinc salt (2=3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Boric acid (H3BO3), zinc salt (2=3). 721.3031 Section 721.3031 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.3031 Boric acid (H3BO...

BASIC study: is intravaginal boric acid non-inferior to metronidazole in symptomatic bacterial vaginosis? Study protocol for a randomized controlled trial.

PubMed

Zeron Mullins, Melinda; Trouton, Konia M

2015-07-26

Bacterial vaginosis is associated with increased transmission of sexually transmitted infections, preterm labor, post-surgical infections, and endometritis. Current treatment for symptomatic bacterial vaginosis includes antibiotics, such as metronidazole, which are 70-80 % effective at one month after treatment and result in high recurrence rates and secondary candida infections. Intravaginal boric acid has been used for over a hundred years to treat vaginal infections, such as bacterial vaginosis. Boric acid is inexpensive, accessible, and has shown to be an effective treatment for other infections, such as vaginal candidiasis. To date, there has been no clinical trial evaluation of boric acid effectiveness to treat bacterial vaginosis. The BASIC (Boric Acid, Alternate Solution for Intravaginal Colonization) trial is a randomized, double-blinded, multicenter study. The study will enroll a minimum of 240 women of 16-50 years of age who are symptomatic with bacterial vaginosis. Eligible participants will have Amsel and Nugent scores confirming bacterial vaginosis. Women who are pregnant or menopausal or have other active co-infections will be excluded. Consenting participants who meet exclusion and inclusion criteria will be randomly assigned to one of three treatment groups: boric acid, metronidazole, or an inert placebo. Self-administration of treatment intravaginally for 10 days will be followed by clinical assessment at 7 and 30 days (days 17 and 40, respectively) after the end of the treatment phase. Primary outcome is a non-inferiority, per-protocol comparison of the effectiveness of boric acid with that of metronidazole at day 17, as measured by the Nugent score in 16-50 year olds. Secondary outcomes include: non-inferiority, intention-to-treat comparison of effectiveness of boric acid with that of metronidazole at day 17, analysis for both per-protocol and intention-to-treat at day 40, and safety considerations, including adverse effects requiring patient discontinuation of treatment. This study will be the first to determine whether intravaginal boric acid is non-inferior to metronidazole in the treatment of bacterial vaginosis in symptomatic women. ClinicalTrials.gov NCT00799214, registered online Nov 10, 2008.

Detrimental effects of boric-acid-treated soil against foraging subterranean termites (Isoptera: Rhinotermitidae)

Treesearch

Bradford M. Kard

2001-01-01

111 laboratory bioassays, boric acid (BA) mixed with soil caused significant subterranean termite mortality. In clloice tests, eastern subterranean and Formosan subterranean tennites were exposed to boric acid mixed with soil at concentrations of 0.05, 0.25, 0.50, 1.00, 2.00, and 4.00 percent Al (wt:wt). Termites could choose to remain in their main nests wit13 non-...

Boric acid increases the expression levels of human anion exchanger genes SLC4A2 and SLC4A3.

PubMed

Akbas, F; Aydin, Z

2012-04-03

Boron is an important micronutrient in plants and animals. The role of boron in living systems includes coordinated regulation of gene expression, growth and proliferation of higher plants and animals. There are several well-defined genes associated with boron transportation and tolerance in plants and these genes show close homology with human anion exchanger genes. Mutation of these genes also characterizes some genetic disorders. We investigated the toxic effects of boric acid on HEK293 cells and mRNA expression of anion exchanger (SLC4A1, SLC4A2 and SLC4A3) genes. Cytotoxicity of boric acid at different concentrations was tested by using the methylthiazolyldiphenyl-tetrazolium bromide assay. Gene expression profiles were examined using quantitative real-time PCR. In the HEK293 cells, the nontoxic upper concentration of boric acid was 250 μM; more than 500 μM caused cytotoxicity. The 250 μM boric acid concentration increased gene expression level of SLC4A2 up to 8.6-fold and SLC4A3 up to 2.6-fold, after 36-h incubation. There was no significant effect of boric acid on SLC4A1 mRNA expression levels.

Boric Acid Inhibits Germination and Colonization of Saprolegnia Spores In Vitro and In Vivo

PubMed Central

Ali, Shimaa E.; Thoen, Even; Evensen, Øystein; Skaar, Ida

2014-01-01

Saprolegnia infections cause severe economic losses among freshwater fish and their eggs. The banning of malachite green increased the demand for finding effective alternative treatments to control the disease. In the present study, we investigated the ability of boric acid to control saprolegniosis in salmon eggs and yolk sac fry. Under in vitro conditions, boric acid was able to decrease Saprolegnia spore activity and mycelial growth in all tested concentrations above 0.2 g/L, while complete inhibition of germination and growth was observed at a concentration of 0.8 g/L. In in vivo experiments using Atlantic salmon eyed eggs, saprolegniosis was controlled by boric acid at concentrations ranging from 0.2–1.4 g/L during continuous exposure, and at 1.0–4.0 g/L during intermittent exposure. The same effect was observed on salmon yolk sac fry exposed continuously to 0.5 g/L boric acid during the natural outbreak of saprolegniosis. During the experiments no negative impact with regard to hatchability and viability was observed in either eggs or fry, which indicate safety of use at all tested concentrations. The high hatchability and survival rates recorded following the in vivo testing suggest that boric acid is a candidate for prophylaxis and control of saprolegniosis. PMID:24699283

Boric acid inhibits germination and colonization of Saprolegnia spores in vitro and in vivo.

PubMed

Ali, Shimaa E; Thoen, Even; Evensen, Øystein; Skaar, Ida

2014-01-01

Saprolegnia infections cause severe economic losses among freshwater fish and their eggs. The banning of malachite green increased the demand for finding effective alternative treatments to control the disease. In the present study, we investigated the ability of boric acid to control saprolegniosis in salmon eggs and yolk sac fry. Under in vitro conditions, boric acid was able to decrease Saprolegnia spore activity and mycelial growth in all tested concentrations above 0.2 g/L, while complete inhibition of germination and growth was observed at a concentration of 0.8 g/L. In in vivo experiments using Atlantic salmon eyed eggs, saprolegniosis was controlled by boric acid at concentrations ranging from 0.2-1.4 g/L during continuous exposure, and at 1.0-4.0 g/L during intermittent exposure. The same effect was observed on salmon yolk sac fry exposed continuously to 0.5 g/L boric acid during the natural outbreak of saprolegniosis. During the experiments no negative impact with regard to hatchability and viability was observed in either eggs or fry, which indicate safety of use at all tested concentrations. The high hatchability and survival rates recorded following the in vivo testing suggest that boric acid is a candidate for prophylaxis and control of saprolegniosis.

Effectiveness of 3 per cent boric acid in 70 per cent alcohol versus 1 per cent clotrimazole solution in otomycosis patients: a randomised, controlled trial.

PubMed

Romsaithong, S; Tomanakan, K; Tangsawad, W; Thanaviratananich, S

2016-09-01

To compare the clinical effectiveness and adverse events for 3 per cent boric acid in 70 per cent alcohol versus 1 per cent clotrimazole solution in the treatment of otomycosis. A total of 120 otomycosis patients were randomly assigned to receive either 1 per cent clotrimazole solution (intervention group) or 3 per cent boric acid in 70 per cent alcohol (control group) at the Khon Kaen Hospital ENT out-patient department. Treatment effectiveness was determined based on the otomicroscopic absence of fungus one week after therapy, following a single application of treatment. After 1 week of treatment, there were data for 109 participants, 54 in the clotrimazole group and 55 in the boric acid group. The absolute difference in cure rates between 1 per cent clotrimazole solution and 3 per cent boric acid in 70 per cent alcohol was 17.9 per cent (95 per cent confidence interval, 2.3 to 33.5; p = 0.028) and the number needed to treat was 6 (95 per cent confidence interval, 3.0 to 43.4). Adverse events for the two agents were comparable. One per cent clotrimazole solution is more effective than 3 per cent boric acid in 70 per cent alcohol for otomycosis treatment.

Boric acid enhances in vivo Ehrlich ascites carcinoma cell proliferation in Swiss albino mice.

PubMed

Qureshi, S; Al-Shabanah, O A; Al-Harbi, M M; Al-Bekairi, A M; Raza, M

2001-08-13

The influence of boric acid, a boron carrier, on Ehrlich ascites carcinoma (EAC) cell-bearing mice was investigated in view of its importance in the boron neutron capture therapy and the influence of boron on proliferation and progression of cancer cells mediated by proteoglycans and collagen. The present study included the evaluation of boric acid for the effects on total count and viability of EAC cells in addition to their non-protein sulfhydryls (NP-SH) and malondialdehyde (MDA) contents as parameters for conjugative detoxication potency and possible oxidative damage. The EAC cell-bearing animals were also observed for the effect on survival, body weight changes, and histopathological evaluation of the tumors grown at the site of inoculation. The treatment with boric acid significantly increased the total number of peritoneal EAC cells and their viability. A significant increase in the body weight was observed that dose-dependently reached plateau levels by 20 days of treatment. Conversely, a reduction in the duration of survival of these animals was evident with the same protocol. Boric acid treatment resulted in a decrease in NP-SH contents with a concomitant increase in MDA levels in EAC cells as revealed by the results of the biochemical analysis. These data are supported by our results on histopathological investigations, which apparently showed fast growth, in addition to several mitotic figures and mixed inflammatory reaction, after treatment with boric acid. It seems likely that a particular combination of properties of boric acid, rather than a single characteristic alone, will provide useful information on the use of this boron carrier in neutron capture therapy.

Effect of application rate and persistence of boric acid sugar baits applied to plants for control of Aedes albopictus.

PubMed

Xue, Rui-De; Müller, Günter C; Kline, Daniel L; Barnard, Donald R

2011-03-01

The use of toxic bait to kill adult Aedes albopictus is a safe and potentially effective alternative to the use of synthetic chemical insecticides. This study was carried out to determine effective concentrations of boric acid needed in sugar bait solutions applied to plant surfaces, and to determine its residual effect in reducing adult mosquito densities. In outdoor tests in 1,100-m3 screened enclosures, landing rates of Ae. albopictus on a human subject and the number of female mosquitoes in mechanical traps were significantly reduced by a 1% boric acid bait compared with the other tested concentrations (0.25%, 0.50%, and 0.75%) and untreated control. Studies of the duration of boric acid activity on plant surfaces were made in 1.4-m3 cages in the laboratory and outdoors in 78-m3 screened enclosures. In the laboratory tests, 1% boric acid bait resulted in >96% mortality in male and female Ae. albopictus for 14 days, whereas in outdoor tests, mosquito landing rates in the treated enclosures were significantly lower than in the control enclosures for 7 days. Also, mosquito mortality responses to boric acid baits between plants with flowers and nonflowers (1.4-m3 cages in the laboratory) were not significantly different. The results of this study suggest that boric acid baits applied to plant surfaces may provide specific data related to the development of an effective point-source-based adjunct/alternative to the use of conventional adulticides for mosquito control.

A randomised controlled trial of active chronic otitis media comparing courses of eardrops versus one-off topical treatments suitable for primary, secondary and tertiary healthcare settings.

PubMed

Loock, J W

2012-08-01

Primary: to compare one-off administration of boric acid powder with courses of 1% acetic acid and ciprofloxacin eardrops in treating active chronic otitis media. Secondary: to evaluate the effectiveness of Quadriderm® cream in resistant active chronic otitis media; and to document side effects of these treatments, especially hearing loss. Randomised controlled trial. Outpatient department of a tertiary ENT unit. Hundred and fifty-nine patients over 6 years old with active chronic mucosal (without cholesteatoma) otitis media randomised to receive one of the three primary agents. All techniques employed were suitable for primary healthcare givers as well as specialists. After confirming eligibility, patients were randomly allocated to treatment. All ears underwent toilet with irrigation using clean water, a syringe and ambient light, with or without dry mopping, until the perforation was visible. The randomised solution was flushed through the middle ear and eustachian tube using a 'tragal pump' technique: saline was used as the solution for flushing in the boric acid powder arm. Patients allocated topical ear medication were given a bottle of eardrops to administer (six drops twice daily, 'pumped in') until finished. Those allocated boric acid powder had the external ear canals filled as a one-off treatment. Patients were followed up monthly thereafter. Primary: Dry (inactive) middle ears as assessed by the doctor. Secondary: Patient assessment of success; microbiologic culture and sensitivity; audiologic changes because of treatment; complications of treatment; costs of therapies. Ciprofloxacin eardrops and boric acid powder were statistically superior to 1% acetic acid eardrops in rendering active chronic otitis media inactive (73% dry ears for ciprofloxacin; 67% for boric acid powder; and 24% for acetic acid). There was no difference between the success rates of ciprofloxacin eardrops and boric acid powder. Quadriderm cream was effective in 85% of patients failing first-line therapy. No agent caused significant complications and specifically no hearing loss. This study showed a single application of boric acid powder following external auditory canal irrigation until the perforation was visible to be as effective as the current best practice of topical quinolone eardrops in active chronic otitis media. Boric acid powder is inexpensive and does not require patient compliance. Boric acid powder is a viable, less costly alternative to topical antibiotic/steroid ear drops in the developing world for active chronic otitis media. Acetic acid eardrops 1% are ineffective. Quadriderm cream, given as a one-off therapy, also appears to be effective. © 2012 Blackwell Publishing Ltd.

Evaluation of Commercially Available Cyanide Test Kits against Various Matrices

DTIC Science & Technology

2016-08-01

further evaluation in a second phase of testing. Cyantesmo paper was tested against 15 matrices, including baking soda, boric acid, brewer’s yeast...matrices were baking soda, boric acid, brewer’s yeast, chalk dust, chitin, coffee powder (instant coffee), cornstarch, drywall dust, flour, kaolin...TN);  DG powdered sugar;  DG talcum powder (Lot 14312THW);  DG Clover Valley baking soda (Lot PMHB51);  Boric acid (Lot 766965; Fisher

High explosive compound

DOEpatents

Crawford, Theodore C.

1976-01-01

1. A low detonation velocity explosive consisting essentially of a particulate mixture of ortho-boric acid and trinitrotoluene, said mixture containing from about 25 percent to about 65 percent by weight of ortho-boric acid, said ortho-boric acid comprised of from 60 percent to 90 percent of spherical particles having a mean particle size of about 275 microns and 10 percent to 40 percent of spherical particles having a particle size less than about 44 microns.

BN Bonded BN fiber article from boric oxide fiber

DOEpatents

Hamilton, Robert S.

1978-12-19

A boron nitride bonded boron nitride fiber article and the method for its manufacture which comprises forming a shaped article with a composition comprising boron oxide fibers and boric acid, heating the composition in an anhydrous gas to a temperature above the melting point of the boric acid and nitriding the resulting article in ammonia gas.

Effect of Boric Acid Supplementation on the Expression of BDNF in African Ostrich Chick Brain.

PubMed

Tang, Juan; Zheng, Xing-ting; Xiao, Ke; Wang, Kun-lun; Wang, Jing; Wang, Yun-xiao; Wang, Ke; Wang, Wei; Lu, Shun; Yang, Ke-li; Sun, Peng-Peng; Khaliq, Haseeb; Zhong, Juming; Peng, Ke-Mei

2016-03-01

The degree of brain development can be expressed by the levels of brain brain-derived neurotrophic factor (BDNF). BDNF plays an irreplaceable role in the process of neuronal development, protection, and restoration. The aim of the present study was to evaluate the effects of boric acid supplementation in water on the ostrich chick neuronal development. One-day-old healthy animals were supplemented with boron in drinking water at various concentrations, and the potential effects of boric acid on brain development were tested by a series of experiments. The histological changes in brain were observed by hematoxylin and eosin (HE) staining and Nissl staining. Expression of BDNF was analyzed by immunohistochemistry, quantitative real-time PCR (QRT-PCR), and enzyme linked immunosorbent assay (ELISA). Apoptosis was evaluated with Dutp-biotin nick end labeling (TUNEL) reaction, and caspase-3 was detected with QRT-PCR. The results were as follows: (1) under the light microscope, the neuron structure was well developed with abundance of neurites and intact cell morphology when animals were fed with less than 160 mg/L of boric acid (groups II, III, IV). Adversely, when boric acid doses were higher than 320 mg/L(groups V, VI), the high-dose boric acid neuron structure was damaged with less neurites, particularly at 640 mg/L; (2) the quantity of BDNF expression in groups II, III, and IV was increased while it was decreased in groups V and VI when compared with that in group I; (3) TUNEL reaction and the caspase-3 mRNA level showed that the amount of cell apoptosis in group II, group III, and group IV were decreased, but increased in group V and group VI significantly. These results indicated that appropriate supplementation of boric acid, especially at 160 mg/L, could promote ostrich chicks' brain development by promoting the BDNF expression and reducing cell apoptosis. Conversely, high dose of boric acid particularly in 640 mg/L would damage the neuron structure of ostrich chick brain by inhibiting the BDNF expression and increasing cell apoptosis. Taken together, the 160 mg/L boric acid supplementation may be the optimal dose for the brain development of ostrich chicks.

Is Boric Acid Toxic to Reproduction in Humans? Assessment of the Animal Reproductive Toxicity Data and Epidemiological Study Results.

PubMed

Duydu, Yalçın; Başaran, Nurşen; Ustündağ, Aylin; Aydın, Sevtap; Undeğer, Ulkü; Ataman, Osman Yavuz; Aydos, Kaan; Düker, Yalçın; Ickstadt, Katja; Waltrup, Brita Schulze; Golka, Klaus; Bolt, Hermann Maximilian

2016-01-01

Boric acid and sodium borates are classified as toxic to reproduction in the CLP Regulation under "Category 1B" with the hazard statement of "H360FD". This classification is based on the reprotoxic effects of boric acid and sodium borates in animal experiments at high doses. However, boron mediated reprotoxic effects have not been proven in epidemiological studies so far. The epidemiological study performed in Bandırma boric acid production plant is the most comprehensive published study in this field with 204 voluntarily participated male workers. Sperm quality parameters (sperm morphology, concentration and motility parameters), FSH, LH and testosterone levels were determined in all participated employees as the reproductive toxicity biomarkers of males. However, boron mediated unfavorable effects on reproduction in male workers have not been determined even in the workers under very high daily boron exposure (0.21 mg B/kg-bw/day) conditions. The NOAEL for rat reproductive toxicity is equivalent to a blood boron level of 2020 ng/g. This level is higher than the mean blood boron concentration (223.89 ± 69.49 ng/g) of the high exposure group workers in Bandırma boric acid production plant (Turkey) by a factor of 9. Accordingly, classifying boric acid and sodium borates under "Category 1B" as "presumed reproductive human toxicant in the CLP regulation seems scientifically not reasonable. The results of the epidemiological studies (including the study performed in China) support for a down-classification of boric acid from the category 1B, H360FD to category 2, H361d, (suspected of damaging the unborn child).

Mechanism of body weight reducing effect of oral boric Acid intake.

PubMed

Aysan, Erhan; Sahin, Fikrettin; Telci, Dilek; Erdem, Merve; Muslumanoglu, Mahmut; Yardımcı, Erkan; Bektasoglu, Huseyin

2013-01-01

Objective. The effect of oral boric acid intake on reducing body weight has been previously demonstrated although the mechanism has been unclear. This research study reveals the mechanism. Subjects. Twelve mice were used, in groups of six each in the control and study groups. For five days, control group mice drank standard tap water while during the same time period the study group mice drank tap water which contains 0.28 mg/250 mL boric acid. After a 5-day period, gene expression levels for uncoupling proteins (UCPs) in the white adipose tissue (WAT), brown adipose tissue (BAT), and skeletal muscle tissue (SMT) and total body weight changes were analyzed. Results. Real time PCR analysis revealed no significant change in UCP3 expressions, but UCP2 in WAT (P: 0.0317), BAT (P: 0.014), and SMT (P: 0.0159) and UCP1 in BAT (P: 0.026) were overexpressed in the boric acid group. In addition, mice in the boric acid group lost body weight (mean 28.1%) while mice in the control group experienced no weight loss but a slight weight gain (mean 0.09%, P < 0.001). Conclusion. Oral boric acid intake causes overexpression of thermogenic proteins in the adipose and skeletal muscle tissues. Increasing thermogenesis through UCP protein pathway results in the accelerated lipolysis and body weight loss.

Synthesis and characterization of boric acid mediated metal-organic frameworks based on trimesic acid and terephthalic acid

NASA Astrophysics Data System (ADS)

Ozer, Demet; Köse, Dursun A.; Şahin, Onur; Oztas, Nursen Altuntas

2017-08-01

The new metal-organic framework materials based on boric acid reported herein. Sodium and boron containing metal-organic frameworks were synthesized by one-pot self-assembly reaction in the presence of trimesic acid and terephthalic acid in water/ethanol solution. Boric acid is a relatively cheap boron source and boric acid mediated metal-organic framework prepared mild conditions compared to the other boron source based metal-organic framework. The synthesized compounds were characterized by FT-IR, p-XRD, TGA/DTA, elemental analysis, 13C-MAS NMR, 11B-NMR and single crystal measurements. The molecular formulas of compounds were estimated as C18H33B2Na5O28 and C8H24B2Na2O17 according to the structural analysis. The obtained complexes were thermally stable. Surface properties of inorganic polymer complexes were investigated by BET analyses and hydrogen storage properties of compound were also calculated.

One-pot synthesis of β-acetamido ketones using boric acid at room temperature.

PubMed

Karimi-Jaberi, Zahed; Mohammadi, Korosh

2012-01-01

β-acetamido ketones were synthesized in excellent yields through one-pot condensation reaction of aldehydes, acetophenones, acetyl chloride, and acetonitrile in the presence of boric acid as a solid heterogeneous catalyst at room temperature. It is the first successful report of boric acid that has been used as solid acid catalyst for the preparation of β-acetamido ketones. The remarkable advantages offered by this method are green catalyst, mild reaction conditions, simple procedure, short reaction times, and good-to-excellent yields of products.

One-Pot Synthesis of β-Acetamido Ketones Using Boric Acid at Room Temperature

PubMed Central

Karimi-Jaberi, Zahed; Mohammadi, Korosh

2012-01-01

β-acetamido ketones were synthesized in excellent yields through one-pot condensation reaction of aldehydes, acetophenones, acetyl chloride, and acetonitrile in the presence of boric acid as a solid heterogeneous catalyst at room temperature. It is the first successful report of boric acid that has been used as solid acid catalyst for the preparation of β-acetamido ketones. The remarkable advantages offered by this method are green catalyst, mild reaction conditions, simple procedure, short reaction times, and good-to-excellent yields of products. PMID:22666168

Some features of the effect the pH value and the physicochemical properties of boric acid have on mass transfer in a VVER reactor's core

NASA Astrophysics Data System (ADS)

Gavrilov, A. V.; Kritskii, V. G.; Rodionov, Yu. A.; Berezina, I. G.

2013-07-01

Certain features of the effect of boric acid in the reactor coolant of nuclear power installations equipped with a VVER-440 reactor on mass transfer in the reactor core are considered. It is determined that formation of boric acid polyborate complexes begins under field conditions at a temperature of 300°C when the boric acid concentration is equal to around 0.065 mol/L (4 g/L). Operations for decontaminating the reactor coolant system entail a growth of corrosion product concentration in the coolant, which gives rise to formation of iron borates in the zones where subcooled boiling of coolant takes place and to the effect of axial offset anomalies. A model for simulating variation of pressure drop in a VVER-440 reactor's core that has invariable parameters during the entire fuel campaign is developed by additionally taking into account the concentrations of boric acid polyborate complexes and the quantity of corrosion products (Fe, Ni) represented by the ratio of their solubilities.

Effect of Boric Acid Concentration on Viscosity of Slag and Property of Weld Metal Obtained from Underwater Wet Welding

NASA Astrophysics Data System (ADS)

Guo, Ning; Guo, Wei; Xu, Changsheng; Du, Yongpeng; Feng, Jicai

2015-06-01

Underwater wet welding is a crucial repair and maintenance technology for nuclear plant. A boric acid environment raises a new challenge for the underwater welding maintenance of nuclear plant. This paper places emphasis on studying the influence of a boric acid environment in nuclear plant on the underwater welding process. Several groups of underwater wet welding experiments have been conducted in boric acid aqueous solution with different concentration (0-35000 ppm). The viscosity of the welding slag and the mechanical properties of welds, such as the hardness, strength, and elongation, have been studied. The results show that with increasing boric acid concentration, the viscosity of the slag decreases first and then increases at a lower temperature (less than 1441 °C). However, when the temperature is above 1480 °C, the differences between the viscosity measurements become less pronounced, and the viscosity tends to a constant value. The hardness and ductility of the joints can be enhanced significantly, and the maximum strength of the weld metal can be reached at 2300 ppm.

Evaluation of boric acid sugar baits against Aedes albopictus (Diptera: Culicidae) in tropical environments.

PubMed

Naranjo, Diana P; Qualls, Whitney A; Müller, Gunter C; Samson, Dayana M; Roque, Deborah; Alimi, Temitope; Arheart, Kristopher; Beier, John C; Xue, Rui-De

2013-04-01

Attractive toxic sugar bait (active ingredient, 1% boric acid) was evaluated against Aedes albopictus Skuse populations in the laboratory, semi-field trials, and field trials in residential communities in St. Augustine, Florida. Laboratory evaluations of boric acid sugar baits applied to the plant Pentas lanceolata (Rubiaceae) demonstrated 100 and 92% mortality of A. albopictus at day 7 and 14, respectively. A semi-field study evaluating the bait application to the upperside or topside of leaves resulted in no significant difference on mortality (P>0.05). Overall combined top and bottom boric acid sugar bait application mortality at day 7 was 95% based on leaf bioassays. Field application of the boric acid sugar baits significantly (P<0.05) decreased adult A. albopictus populations up to day 21 post-treatment compared to the pre-treatment population numbers. A significant reduction in oviposition was demonstrated both at day 7 and 14 post-application (P=0.001) as monitored by ovitraps. Attractive toxic sugar bait application in tropical environments demonstrated efficacy, persistence, and feasibility in controlling A. albopictus populations.

Matrix Effects on Boron Containing Materials due to Laser Ablation Molecular Isotopic Spectrometry (LAMIS)

NASA Astrophysics Data System (ADS)

Brown, Staci R.; Akpovo, Charlemagne A.; Martinez, Jorge; Ford, Alan; Herbert, Kenley; Johnson, Lewis

2014-03-01

Laser Induced Breakdown Spectroscopy (LIBS) is a spectroscopic technique that is used for the qualitative and quantitative analysis of materials in the liquid, solid, or gas phase. LIBS can also be used for the detection of isotopic shifts in atomic and diatomic species via Laser-Ablation Molecular Isotopic Spectroscopy (LAMIS). However, any additional elements that are entrained into the plasma other than the element of interest, can affect the extent of ablation and quality of spectra and hence, potentially obscure or aid in the relative abundance assessment for a given element. To address the importance of matrix effects, the isotopic analysis of boron obtained from boron oxide (BO) emission originating from different boron-containing compounds, such as boron nitride (BN), boric acid (H3BO3) , and borax (Na2B4O710H2O), via LIBS has been performed here. Each of these materials has different physical properties and elemental composition in order to illustrate possible challenges for the LAMIS method. A calibration-free model similar to that for the original LAMIS work is used to determine properties of the plasma as the matrix is changed. DTRA

Boric acid poisoning

MedlinePlus

... effectively treat (adsorb) boric acid. For skin exposure, treatment may include: Surgical removal of burned skin (debridement) Transfer to a hospital that specializes in burn care Washing of the skin (irrigation), possibly every ...

Boric Acid and Commercial Organoboron Products as Inhibitors of Drug-Resistant Candida albicans.

PubMed

Larsen, Bryan; Petrovic, Marija; De Seta, Francesco

2018-04-01

Clinical use of boric acid as a topical antifungal in women who have failed standard antifungal therapy with azole drugs has been used sporadically for decades. Our previous in vitro work showing inhibition of Candida albicans growth was conducted on clinical isolates without antifungal drug susceptibility profiling. Here, we report that boric acid restricts growth of drug-resistant Candida albicans and inhibits hyphal growth and diminishes cell volume. The availability of over-the-counter organoboron compounds intended for use as oral nutritional supplements led us to determine if these also were inhibitory toward resistant Candida and show here that they also possess antifungal activity. Candida glabrata was also found to be inhibited by boric acid and organoboron compounds. Further development of organoboron compounds as topical therapeutics is of potential value.

Boric acid solution concentration influencing p-type emitter formation in n-type crystalline Si solar cells

NASA Astrophysics Data System (ADS)

Singha, Bandana; Singh Solanki, Chetan

2016-09-01

Boric acid (BA) is a spin on dopant (BSoD) source which is used to form p+ emitters in n-type c-Si solar cells. High purity boric acid powder (99.99% pure) when mixed with deionized (DI) water can result in high quality p-type emitter with less amount of surface defects. In this work, we have used different concentrations of boric acid solution concentrations to fabricate p-type emitters with sheet resistance values < 90 Ω/□. The corresponding junction depths for the same are less than 500 nm as measured by SIMS analysis. Boron rich layer (BRL), which is considered as detrimental in emitter performance is found to be minimal for BA solution concentration less than 2% and hence useful for p-type emitter formation.

BCN Graphene as Efficient Metal-Free Electrocatalyst for the Oxygen Reduction Reaction

DTIC Science & Technology

2012-01-01

annealing GO in the presence of boric acid and ammonia. The resultant BCN graphene was shown to have superior electrocatalytic activities to the commercial...graphene samples of different chemical compositions, along with the mixture of GO and boric acid (B-GO) starting material as reference. Comparing with the...in addition to B into GO by thermal annealing in the presence of boric acid and ammonia. Like VA-BCN nanotubes,[15] the presence of a O1s peak in the

Effect of boric acid on antioxidant enzyme activity, lipid peroxidation, and ultrastructure of midgut and fat body of Galleria mellonella.

PubMed

Büyükgüzel, Ender; Büyükgüzel, Kemal; Snela, Milena; Erdem, Meltem; Radtke, Katarzyna; Ziemnicki, Kazimierz; Adamski, Zbigniew

2013-04-01

Boric acid is widely used as an insecticide, acaricide, herbicide, and fungicide and also during various industrial processings. Hence, numerous populations are subjects to this toxic compound. Its action on animals is still not fully known and understood. We examined the effect of boric acid on larvae of greater wax moth (Galleria mellonella). The chemical appeared to be toxic for larvae, usually in a concentration-dependent manner. Exposed groups revealed increased lipid peroxidation and altered activity of catalase, superoxide dismutase, glutathione S-transferase, and glutathione peroxidase. We also observed changes of ultrastructure, which were in tune with biochemical assays. We suggest that boric acid has a broad mode of action, which may affect exposed larvae, and even if sublethal, they may lead to disturbances within exposed populations.

Thermal and Mechanical Characteristics of Polymer Composites Based on Epoxy Resin, Aluminium Nanopowders and Boric Acid

NASA Astrophysics Data System (ADS)

Nazarenko, O. B.; Melnikova, T. V.; Visakh, P. M.

2016-01-01

The epoxy polymers are characterized by low thermal stability and high flammability. Nanoparticles are considered to be effective fillers of polymer composites for improving their thermal and functional properties. In this work, the epoxy composites were prepared using epoxy resin ED-20, polyethylene polyamine as a hardener, aluminum nanopowder and boric acid fine powder as flame-retardant filler. The thermal characteristics of the obtained samples were studied using thermogravimetric analysis and differential scanning calorimetry. The mechanical characteristics of epoxy composites were also studied. It was found that an addition of all fillers enhances the thermal stability and mechanical characteristics of the epoxy composites. The best thermal stability showed the epoxy composite filled with boric acid. The highest flexural properties showed the epoxy composite based on the combination of boric acid and aluminum nanopowder.

Evaluation of commercial boric acid containing vials for urine culture: low risk of contamination and cost effectiveness considerations.

PubMed

Appannanavar, Suma B; Biswal, Manisha; Rajkumari, Nonika; Mohan, Balvinder; Taneja, Neelam

2013-01-01

Urine culture is a gold standard in the diagnosis of urinary tract infection. Clean catch midstream urine collection and prompt transportation is essential for appropriate diagnosis. Improper collection and delay in transportation leads to diagnostic dilemma. In developing countries, higher ambient temperatures further complicate the scenario. Here, we have evaluated the role of boric acid as a preservative for urine samples prior to culture in female patients attending outpatient department at our center. Consecutive 104 urine samples were cultured simultaneously in plain uricol (Control-C) and boric acid containing tubes from Becton Dickinson urine culture kit (Boric acid group-BA). In the real-time evaluation, we found that in almost 57% (59/104) of the urine samples tested, it was more effective in maintaining the number of the organisms as compared to samples in the container without any preservative. Our in vitro study of simulated urine cultures revealed that urine samples could be kept up to 12 h before culture in the preservative without any inhibitory effect of boric acid. Though the use of boric acid kit may marginally increase the initial cost but has indirect effects like preventing delays in treatment and avoidance of false prescription of antibiotics. If the man-hours spent on repeat investigations are also taken into consideration, then the economic cost borne by the laboratory would also decrease manifold with the use of these containers.

Gold Nanoplates for a Localized Surface Plasmon Resonance-Based Boric Acid Sensor

PubMed Central

Morsin, Marlia; Mat Salleh, Muhamad; Ali Umar, Akrajas; Sahdan, Mohd Zainizan

2017-01-01

Localized surface plasmon resonance (LSPR) properties of metallic nanostructures, such as gold, are very sensitive to the dielectric environment of the material, which can simply be adjusted by changing its shape and size through modification of the synthesizing process. Thus, these unique properties are very promising, particularly for the detection of various types of chemicals, for example boric acid which is a non-permitted preservative employed in food preparations. For the sensing material, gold (Au) nanoplates with a variety of shapes, i.e., triangular, hexagonal, truncated pentagon and flat rod, were prepared using a seed-mediated growth method. The yield of Au nanoplates was estimated to be ca. 63% over all areas of the sensing material. The nanoplates produced two absorption bands, i.e., the transverse surface plasmon resonance (t-SPR) and the longitudinal surface plasmon resonance (l-SPR) at 545 nm and 710 nm, respectively. In the sensing study, these two bands were used to examine the response of gold nanoplates to the presence of boric acid in an aqueous environment. In a typical process, when the sample is immersed into an aqueous solution containing boric acid, these two bands may change their intensity and peak centers as a result of the interaction between the boric acid and the gold nanoplates. The changes in the intensities and peak positions of t-SPR and l-SPR linearly correlated with the change in the boric acid concentration in the solution. PMID:28441323

Temperature-Dependent Effect of Boric Acid Additive on Surface Roughness and Wear Rate

NASA Astrophysics Data System (ADS)

Ekinci, Şerafettin

Wear and friction hold an important place in engineering. Currently, scientific societies are struggling to control wear by means of studies on lubricants. Boric acid constitutes an important alternative with its good tribological properties similar to MO2S and graphite alongside with low environmental impacts. Boric acid can be used as a solid lubricant itself whereas it can be added or blended into mineral oils in order to yield better mechanical and tribological properties such as low shear stress due to the lamellar structure and low friction, wear and surface roughness rates. In this study, distinguishing from the literature, boric acid addition effect considering the temperature was investigated for the conventional ranges of internal combustion engines. Surface roughness, wear and friction coefficient values were used in order to determine tribological properties of boric acid as an environmentally friendly additive and mineral oil mixture in the present study. Wear experiments were conducted with a ball on disc experimental setup immersed in an oil reservoir at room temperature, 50∘C and 80∘C. The evolution of both the friction coefficient and wear behavior was determined under 10N load, at 2m/s sliding velocity and a total sliding distance of 9000m. Surface roughness was determined using atomic-force microscopy (AFM). Wear rate was calculated utilizing scanning electron microscope (SEM) visuals and data. The test results showed that wear resistance increased as the temperature increased, and friction coefficient decreased due to the presence of boric acid additive.

Gold Nanoplates for a Localized Surface Plasmon Resonance-Based Boric Acid Sensor.

PubMed

Morsin, Marlia; Mat Salleh, Muhamad; Ali Umar, Akrajas; Sahdan, Mohd Zainizan

2017-04-25

Localized surface plasmon resonance (LSPR) properties of metallic nanostructures, such as gold, are very sensitive to the dielectric environment of the material, which can simply be adjusted by changing its shape and size through modification of the synthesizing process. Thus, these unique properties are very promising, particularly for the detection of various types of chemicals, for example boric acid which is a non-permitted preservative employed in food preparations. For the sensing material, gold (Au) nanoplates with a variety of shapes, i.e., triangular, hexagonal, truncated pentagon and flat rod, were prepared using a seed-mediated growth method. The yield of Au nanoplates was estimated to be ca. 63% over all areas of the sensing material. The nanoplates produced two absorption bands, i.e., the transverse surface plasmon resonance (t-SPR) and the longitudinal surface plasmon resonance (l-SPR) at 545 nm and 710 nm, respectively. In the sensing study, these two bands were used to examine the response of gold nanoplates to the presence of boric acid in an aqueous environment. In a typical process, when the sample is immersed into an aqueous solution containing boric acid, these two bands may change their intensity and peak centers as a result of the interaction between the boric acid and the gold nanoplates. The changes in the intensities and peak positions of t-SPR and l-SPR linearly correlated with the change in the boric acid concentration in the solution.

Amorphous titania modified with boric acid for selective capture of glycoproteins.

PubMed

Jin, Shanxia; Liu, Liping; Zhou, Ping

2018-05-22

Amorphous titania was modified with boric acid, and the resulting material was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray powder diffraction and X-ray photoelectron spectrometry. The new material, in contrast to conventional boronate affinity materials containing boronic acid ligands, bears boric acid groups. It is shown to exhibit high specificity for glycoproteins, and this was applied to design a method for solid phase extraction of glycoproteins as shown for ribonuclease B, horse radish peroxidase and ovalbumin. Glycoproteins were captured under slightly alkaline environment and released in acidic solutions. The glycoproteins extracted were detected by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. The binding capacities for ribonuclease B, horse radish peroxidase and ovalbumin typically are 9.3, 26.0 and 53.0 mg ∙ g -1 , respectively. The method was successfully applied to the selective enrichment of ovalbumin from egg white. Graphical abstract Schematic presentation of the capture of glycoproteins by amorphous titania modified with boric acid.

Lugol's solution eradicates Staphylococcus aureus biofilm in vitro.

PubMed

Grønseth, Torstein; Vestby, Lene K; Nesse, Live L; Thoen, Even; Habimana, Olivier; von Unge, Magnus; Silvola, Juha T

2017-12-01

The aim of the study was to evaluate the antibacterial efficacy of Lugol's solution, acetic acid, and boric acid against Staphylococcus aureus biofilm. The efficacy of Lugol's solution 1%, 0.1%, and 0.05%, acetic acid 5% or boric acid 4.7% for treatment of Staphylococcus aureus biofilm in vitro was tested using 30 clinical strains. Susceptibility in the planktonic state was assessed by disk diffusion test. Antiseptic effect on bacteria in biofilm was evaluated by using a Biofilm-oriented antiseptic test (BOAT) based on metabolic activity, a biofilm bactericidal test based on culturing of surviving bacteria and confocal laser scanning microscopy combined with LIVE/DEAD staining. In the planktonic state, all tested S. aureus strains were susceptible to Lugol's solution and acetic acid, while 27 out of 30 tested strains were susceptible to boric acid. In biofilm the metabolic activity was significantly reduced following exposure to Lugol's solution and 5% acetic acid, while boric acid exposure led to no significant changes in metabolic activities. In biofilm, biocidal activity was observed for Lugol's solution 1% (30/30), 0.1% (30/30), and 0.05% (26/30). Acetic acid and boric acid showed no bactericidal activity in this test. Confocal laser scanning microscopy, assessed in 4/30 strains, revealed significantly fewer viable biofilm bacteria with Lugol's solution (1% p < 0.001, 0.1% p = 0.001 or 0.05% p = 0.001), acetic acid 5% for 10 min (p = 0.001) or 30 min (p = 0.015), but not for acetic acid for 1 min or boric acid. Lugol's solution 1.0% and 0.1% effectively eradicated S. aureus in biofilm and could be an alternative to conventional topical antibiotics where S. aureus biofilm is suspected such as external otitis, pharyngitis and wounds. Copyright © 2017 Elsevier B.V. All rights reserved.

BIO-PRECIPITATES PRODUCED BY TWO AUTOCHTHONOUS BORON TOLERANT STREPTOMYCES STRAINS.

PubMed

Moraga, Norma Beatriz; Irazusta, Verónica; Amoroso, María Julia; Rajal, Verónica Beatriz

2017-08-01

Boron is widespread in the environment. Although contaminated soils are hard to recover different strategies have been investigated in the recent years. Bioremediation is one of the most studied because it is eco-friendly and less costly than other techniques. The aim of this research was to evaluate whether two Streptomyces strains isolated from boron contaminated soils in Salta, Argentina, may help remove boron from such soils. For this, they were grown in different liquid media with two boric acid concentrations and their specific growth rate and specific boric acid consumption rate were determined. Both strains showed great capacity to remove boron from the media. Increasing boric acid concentrations affected negatively the specific growth rate, however the specific boric acid consumption rate was superior. Boron bio-precipitates were observed when the strains grew in the presence of boric acid, probably due to an adaptive response developed by the cells to the exposure, for which many proteins were differentially synthetized. This strategy to tolerate high concentrations of boron by immobilizing it in bio-precipitates has not been previously described, to the best of our knowledge, and may have a great potential application in remediating soils contaminated with boron compounds.

Boron modulates extracellular matrix and TNF alpha synthesis in human fibroblasts.

PubMed

Benderdour, M; Hess, K; Dzondo-Gadet, M; Nabet, P; Belleville, F; Dousset, B

1998-05-29

Boric acid was not mitogenic for human fibroblasts and it did not change cell viability until 0.5% (w/v). Boric acid treatment affected the metabolism of human dermal fibroblasts in culture, decreasing the synthesis of extracellular matrix macromolecules such as proteoglycans, collagen, and total proteins. It also increased the release of these molecules into the culture medium. The principal proteins secreted into the medium after boric acid treatment had molecular masses of 90, 70, 58, 49, and 43 kDa and faint bands were detected by electrophoresis between 14 and 30 kDa. hsp 70 and TNF alpha were detected among the secreted proteins by immunoblotting, and the amount of TNF alpha released was quantified by radioimmunoassay. Total mRNA levels were higher after boric acid treatment and peaked after 6 h of treatment. TNF alpha mRNA was undetectable in unstimulated fibroblasts and two TNF alpha mRNA bands were detected after stimulation: immature mRNA (4.8 kb) and mature TNF alpha mRNA (1.9 kb). Thus, the effects of boric acid observed in wound repair in vivo may be due to TNF alpha synthesis and secretion.

Ecofriendly Fire Retardant and Rot Resistance Finishing of Jute Fabric Using Tin and Boron Based Compound

NASA Astrophysics Data System (ADS)

Samanta, Ashis Kumar; Bagchi, Arindam

2017-06-01

Treatment with sodium stannate followed by treatment with boric acid imparts jute fabric wash fast fire resistance property as indicated by its Limiting Oxygen Index (LOI) value and 45° inclined flammability test results. The treatment was carried out by impregnation of sodium stannate followed by impregnation with an aqueous solution of boric acid and drying. Application of sodium stannate (20%) and boric acid (20%) treatment on jute fabric showed balanced flame retardancy property (LOI value 34) with some loss in fabric tenacity (loss of tenacity is 14.5%). Treated fabric retained good fire retardant property after three consecutive washing. Treated fabric also possessed good rot resistance property as indicated by soil burial test and strength retention after 21 days soil burial was found to be 65%. It is found that of sodium stannate and boric acid combination by double bath process form a synergistic durable fire-retardant as well as rot resistant when impregnated on jute material, which is considerably greater than the use of either sodium stannate or boric acid alone. TGA, FTIR and SEM analysis are also reported to support the results and reaction mechanism.

Toxicological and histopathological effects of boric acid on Atta sexdens rubropilosa (Hymenoptera: Formicidae) workers.

PubMed

Sumida, Simone; Silva-Zacarin, Elaine C M; Decio, Pâmela; Malaspina, Osmar; Bueno, Fabiana C; Bueno, Odair C

2010-06-01

The current study compared the toxicity of different concentrations of boric acid in adult workers of Atta sexdens rubropilosa Forel (Hymenoptera: Formicidae), with toxicological bioassays, and examining the dose-dependent and time-dependent histopathological changes, of the midgut, Malpighian tubules, and postpharyngeal glands. Our results revealed the importance of conducting toxicological bioassays combined with morphological analyses of the organs of ants chronically exposed to insecticides used in commercial ant baits. In vitro bioassays showed that boric acid significantly decreases the survivorship of workers regardless of concentration, whereas the morphological data suggested progressive dose-dependent and time-dependent changes in the organs examined, which were evident in the midgut. The midgut is the first organ to be affected, followed by the postpharyngeal gland and Malpighian tubules. This sequence is in agreement with the absorption pathway of this chemical compound in the midgut, its transference to the hemolymph, possibly reaching the postpharyngeal glands, and excretion by the Malpighian tubules. These progressive changes might be due to the cumulative and delayed effect of boric acid. Our findings provide important information for the understanding of the action of boric acid in ant baits in direct and indirect target organs.

Study of structural, surface and hydrogen storage properties of boric acid mediated metal (sodium)-organic frameworks

NASA Astrophysics Data System (ADS)

Ozer, Demet; Köse, Dursun A.; Sahin, Onur; Oztas, Nursen A.

2018-04-01

Three boric acid mediated metal organic frameworks were synthesized by solution method with using succinic acid, fumaric acid and acetylene dicarboxylic acid as a ligand source and sodium as a metal source. The complexes were characterized by FT-IR, powder XRD, elemental analyses and single crystal measurements. The complexes with the formula, C4H18B2Na2O14, C4H16B2Na2O14 and C4H14B2Na2O14 were successfully obtained. BET surface area of complexes were calculated and found as 13.474 m2/g for catena-(tetrakis(μ2-hydroxo)-(μ2-trihydrogen borate)-(μ2-succinato)-di-sodium boric acid solvate), 1.692 m2/g for catena-(tetrakis(μ2-hydroxo)-(μ2-trihydrogen borate)-(μ2-fumarato)-di-sodium boric acid solvate) and 5.600 m2/g for catena-(tetrakis(μ2-hydroxo)-(μ2-trihydrogen borate)-(μ2-acetylenedicarboxylato)-di-sodium boric acid solvate). Hydrogen storage capacities of the complexes were also studied at 77 K 1 bar pressure and found as 0.108%, 0.033%, 0.021% by mass. When different ligands were used, the pore volume, pore width and surface area of the obtained complexes were changed. As a consequence, hydrogen storage capacities also changed.

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.; Stone, M. E.

2013-08-14

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01M) boric acid stream intomore » the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B2O3 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 – SB8 flowsheet to additions of B2O3 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 – SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B2O3 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B2O3 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT. The impact on CPC processing of a 0.01M boric acid solution for elution of cesium during Modular Caustic Side Solvent Extraction Unit (MCU) processing has previously been evaluated by the Savannah River National Laboratory (SRNL). Increasing the acid strength to 0.0125M boric acid to account for variations in the boric acid strength has been reviewed versus the previous evaluation. The amount of acid from the boric acid represented approximately 5% of the total acid during the previous evaluation. An increase from 0.01 to 0.0125M boric acid represents a change of approximately 1.3% which is well within the error of the acid calculation. Therefore, no significant changes to CPC processing (hydrogen generation, metal solubilities, rheological properties, REDOX control, etc.) are expected from an increase in allowable boric acid concentration from 0.01M to 0.0125M.« less

Dermatitis toxica faciei after boric acid.

PubMed

Jiráková, Anna; Rajská, Lucie; Rob, Filip; Gregorová, Jana; Hercogová, Jana

2015-01-01

An adverse toxic reaction to the topical application of a 2% boric acid solution is described in a 2-year-old girl. Topical boric acid is licensed for use in children above the age of 10 in the Czech Republic. However, it can be bought over the counter and it is very often used in younger children. Due to its fast absorption and slow elimination, there is a high risk of systemic side effects. On the other hand, topical side effects are not reported in the present literature. © 2014 Wiley Periodicals, Inc.

Effect of Boric Acid on Volatile Products of Thermooxidative Degradation of Epoxy Polymers

NASA Astrophysics Data System (ADS)

Nazarenko, O. B.; Bukhareva, P. B.; Melnikova, T. V.; Visakh, P. M.

2016-01-01

The polymeric materials are characterized by high flammability. The use of flame retardants in order to reduce the flammability of polymers can lead to the formation of toxic gaseous products under fire conditions. In this work we studied the effect of boric acid on the volatile products of thermooxidative degradation of epoxy polymers. The comparative investigations were carried out on the samples of the unfilled epoxy resin and epoxy resin filled with a boric acid at percentage 10 wt. %. The analysis of the volatile decomposition products and thermal stability of the samples under heating in an oxidizing medium was performed using a thermal mass-spectrometric analysis. It is found that the incorporation of boric acid into the polymer matrix increases the thermal stability of epoxy composites and leads to a reduction in the 2-2.7 times of toxic gaseous products

Hearing loss effects of administering boric alcohol solution prepared with alcohol in various degrees on guinea pigs (an experimental study).

PubMed

Aktas, Sinem; Basoglu, Mehmet Sinan; Aslan, Hale; Ilknur, Ali Ekber; Dundar, Riza; Katilmis, Huseyin; Ozturkcan, Sedat

2013-09-01

To investigate the ototoxic effect of boric acid solution prepared with different degree of alcohol. This study was performed on 28 young albino guinea pigs. After the animals divided four groups prior to the application of the solution an auditory brainstem response (ABR) test was applied to the each animal under general anesthesia. Their tympanic membranes perforated and test solutions were administrated to the middle ear through the perforation. On 15th day, ABR measurements were carried out and comparison was made with preadministration values. The degrees of hearing loss occurring as a result of the administration of 4% boric alcohol solutions prepared with 60° and 40° alcohol differed significantly (p < 0.001). It was established that 4% boric acid solution prepared with 60 alcohol affected hearing in guinea pigs more negatively and an increase in degree of alcohol also increased the ototoxicity of the boric acid solution. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Decay resistance of wood treated with boric acid and tall oil derivates.

PubMed

Temiz, Ali; Alfredsen, Gry; Eikenes, Morten; Terziev, Nasko

2008-05-01

In this study, the effect of two boric acid concentrations (1% and 2%) and four derivates of tall oil with varying chemical composition were tested separately and in combination. The tall oil derivates were chosen in a way that they consist of different amounts of free fatty, resin acids and neutral compounds. Decay tests using two brown rot fungi (Postia placenta and Coniophora puteana) were performed on both unleached and leached test samples. Boric acid showed a low weight loss in test samples when exposed to fungal decay before leaching, but no effect after leaching. The tall oil derivates gave better efficacy against decay fungi compared to control, but are not within the range of the efficacy needed for a wood preservative. Double impregnation with boric acid and tall oil derivates gave synergistic effects for several of the double treatments both in unleached and leached samples. In the unleached samples the double treatment gave a better efficacy against decay fungi than tall oil alone. In leached samples a better efficacy against brown rot fungi were achieved than in samples with boron alone and a nearly similar or better efficacy than for tall oil alone. Boric acid at 2% concentration combined with the tall oil derivate consisting of 90% free resin acids (TO-III) showed the best performance against the two decay fungi with a weight loss less than 3% after a modified pure culture test.

Boric acid reduces axonal and myelin damage in experimental sciatic nerve injury

PubMed Central

Kızılay, Zahir; Erken, Haydar Ali; Çetin, Nesibe Kahraman; Aktaş, Serdar; Abas, Burçin İrem; Yılmaz, Ali

2016-01-01

The aim of this study was to investigate the effects of boric acid in experimental acute sciatic nerve injury. Twenty-eight adult male rats were randomly divided into four equal groups (n = 7): control (C), boric acid (BA), sciatic nerve injury (I), and sciatic nerve injury + boric acid treatment (BAI). Sciatic nerve injury was generated using a Yasargil aneurysm clip in the groups I and BAI. Boric acid was given four times at 100 mg/kg to rats in the groups BA and BAI after injury (by gavage at 0, 24, 48 and 72 hours) but no injury was made in the group BA. In vivo electrophysiological tests were performed at the end of the day 4 and sciatic nerve tissue samples were taken for histopathological examination. The amplitude of compound action potential, the nerve conduction velocity and the number of axons were significantly lower and the myelin structure was found to be broken in group I compared with those in groups C and BA. However, the amplitude of the compound action potential, the nerve conduction velocity and the number of axons were significantly greater in group BAI than in group I. Moreover, myelin injury was significantly milder and the intensity of nuclear factor kappa B immunostaining was significantly weaker in group BAI than in group I. The results of this study show that administration of boric acid at 100 mg/kg after sciatic nerve injury in rats markedly reduces myelin and axonal injury and improves the electrophysiological function of injured sciatic nerve possibly through alleviating oxidative stress reactions. PMID:27904499

Loci Contributing to Boric Acid Toxicity in Two Reference Populations of Drosophila melanogaster

PubMed Central

Najarro, Michael A.; Hackett, Jennifer L.; Macdonald, Stuart J.

2017-01-01

Populations maintain considerable segregating variation in the response to toxic, xenobiotic compounds. To identify variants associated with resistance to boric acid, a commonly-used household insecticide with a poorly understood mechanism of action, we assayed thousands of individuals from hundreds of strains. Using the Drosophila Synthetic Population Resource (DSPR), a multi-parental population (MPP) of inbred genotypes, we mapped six QTL to short genomic regions containing few protein-coding genes (3–188), allowing us to identify plausible candidate genes underlying resistance to boric acid toxicity. One interval contains multiple genes from the cytochrome P450 family, and we show that ubiquitous RNAi of one of these genes, Cyp9b2, markedly reduces resistance to the toxin. Resistance to boric acid is positively correlated with caffeine resistance. The two phenotypes additionally share a pair of QTL, potentially suggesting a degree of pleiotropy in the genetic control of resistance to these two distinct xenobiotics. Finally, we screened the Drosophila Genetic Reference Panel (DGRP) in an attempt to identify sequence variants within mapped QTL that are associated with boric acid resistance. The approach was largely unsuccessful, with only one QTL showing any associations at QTL-specific 20% False Discovery Rate (FDR) thresholds. Nonetheless, these associations point to a potential candidate gene that can be targeted in future validation efforts. Although the mapping data resulting from the two reference populations do not clearly overlap, our work provides a starting point for further genetic dissection of the processes underlying boric acid toxicity in insects. PMID:28592646

The effect of zinc injection on the increasing of Inconel 600 TT corrosion resistances

NASA Astrophysics Data System (ADS)

Febrianto; Sriyono; Widodo, Surip; Sunaryo, Geni Rina

2018-02-01

Many failures were found in reactor pressure vessel head penetration (RPV) head material. Those failures caused by boric acid corrosion, and from visual examination were found a big hole and white deposit crystal of boric acid during shutdown maintenance at David Besse reactor. Zinc Oxide addition in BWR reactor known as Zinc Injection that has purposed to reduce radiation exposure cause of Hydrogen addition. Beside reducing the radiation exposure, Zinc injection also has an effect in reducing material corrosion. The purpose of study is to determine the effect of zinc addition, boric acid, temperature also the effects of Cobalt Nitrate and Zinc Oxide addition to Inconel 600 TT as RPV head penetration material. The result in the BWR reactor experience will be implementated at PWR reactor, weather zinc oxide addition also has an effect in reducing the corrosion of Inconel 600. The method that used in this research is to observe the corrosion rates for Inconel 600 material using Potentiostat. Examination were conducted in 30, 40, 60, 70, 80 and 80 °C using 1000, 1500, 2000, 2500 and 3000 ppm boric acid concentration. The results showed that the corrosion rate for the material were very small, but the highest corrosion rate occurred in 3000 ppm boric acid concentration at 90 °C with Cobalt Nitrate addition, around 5.210 x 10-1 mpy. In the same condition at 3000 ppm boric acid concentration for temperature at 90 °C, Inconel 600 TT corrosion rate is smaller with Zinc oxide addition, around 4.631 x 10-1 mpy.

Boric acid reduces axonal and myelin damage in experimental sciatic nerve injury.

PubMed

Kızılay, Zahir; Erken, Haydar Ali; Çetin, Nesibe Kahraman; Aktaş, Serdar; Abas, Burçin İrem; Yılmaz, Ali

2016-10-01

The aim of this study was to investigate the effects of boric acid in experimental acute sciatic nerve injury. Twenty-eight adult male rats were randomly divided into four equal groups ( n = 7): control (C), boric acid (BA), sciatic nerve injury (I), and sciatic nerve injury + boric acid treatment (BAI). Sciatic nerve injury was generated using a Yasargil aneurysm clip in the groups I and BAI. Boric acid was given four times at 100 mg/kg to rats in the groups BA and BAI after injury (by gavage at 0, 24, 48 and 72 hours) but no injury was made in the group BA. In vivo electrophysiological tests were performed at the end of the day 4 and sciatic nerve tissue samples were taken for histopathological examination. The amplitude of compound action potential, the nerve conduction velocity and the number of axons were significantly lower and the myelin structure was found to be broken in group I compared with those in groups C and BA. However, the amplitude of the compound action potential, the nerve conduction velocity and the number of axons were significantly greater in group BAI than in group I. Moreover, myelin injury was significantly milder and the intensity of nuclear factor kappa B immunostaining was significantly weaker in group BAI than in group I. The results of this study show that administration of boric acid at 100 mg/kg after sciatic nerve injury in rats markedly reduces myelin and axonal injury and improves the electrophysiological function of injured sciatic nerve possibly through alleviating oxidative stress reactions.

Loci Contributing to Boric Acid Toxicity in Two Reference Populations of Drosophila melanogaster.

PubMed

Najarro, Michael A; Hackett, Jennifer L; Macdonald, Stuart J

2017-06-07

Populations maintain considerable segregating variation in the response to toxic, xenobiotic compounds. To identify variants associated with resistance to boric acid, a commonly-used household insecticide with a poorly understood mechanism of action, we assayed thousands of individuals from hundreds of strains. Using the Drosophila Synthetic Population Resource (DSPR), a multi-parental population (MPP) of inbred genotypes, we mapped six QTL to short genomic regions containing few protein-coding genes (3-188), allowing us to identify plausible candidate genes underlying resistance to boric acid toxicity. One interval contains multiple genes from the cytochrome P450 family, and we show that ubiquitous RNAi of one of these genes, Cyp9b2 , markedly reduces resistance to the toxin. Resistance to boric acid is positively correlated with caffeine resistance. The two phenotypes additionally share a pair of QTL, potentially suggesting a degree of pleiotropy in the genetic control of resistance to these two distinct xenobiotics. Finally, we screened the Drosophila Genetic Reference Panel (DGRP) in an attempt to identify sequence variants within mapped QTL that are associated with boric acid resistance. The approach was largely unsuccessful, with only one QTL showing any associations at QTL-specific 20% False Discovery Rate (FDR) thresholds. Nonetheless, these associations point to a potential candidate gene that can be targeted in future validation efforts. Although the mapping data resulting from the two reference populations do not clearly overlap, our work provides a starting point for further genetic dissection of the processes underlying boric acid toxicity in insects. Copyright © 2017 Najarro et al.

Effects of surface inactivation, high temperature drying and preservative treatment on surface roughness and colour of alder and beech wood

NASA Astrophysics Data System (ADS)

Aydin, Ismail; Colakoglu, Gursel

2005-10-01

Although extensive research has been conducted in wood surface quality analysis, a unified approach to surface quality characterisation does not exist. Measurements of the variation in surface roughness and surface colour are used widely for the evaluation of wood surface quality. Colour is a basic visual feature for wood and wood-based products. Colour measurement is one of the quality control tests that should be carried out because the colour deviations are spotted easily by the consumers. On the other hand, a common problem faced by plywood manufacturers is panel delamination, for which a major cause is poor quality glue-bonds resulting from rough veneer. Rotary cut veneers with dimensions of 500 mm × 500 mm × 2 mm manufactured from alder ( Alnus glutinosa subsp. barbata) and beech ( Fagus orientalis Lipsky) logs were used as materials in this study. Veneer sheets were oven-dried in a veneer dryer at 110 °C (normal drying temperature) and 180 °C (high drying temperature) after peeling process. The surfaces of some veneers were then exposed at indoor laboratory conditions to obtain inactive wood surfaces for glue bonds, and some veneers were treated with borax, boric acid and ammonium acetate solutions. After these treatments, surface roughness and colour measurements were made on veneer surfaces. High temperature drying process caused a darkening on the surfaces of alder and beech veneers. Total colour change value (Δ E*) increased linear with increasing exposure time. Among the treatment solutions, ammonium acetate caused the biggest colour change while treatment with borax caused the lowest changes in Δ E* values. Considerable changes in surface roughness after preservative treatment did not occur on veneer surfaces. Generally, no clear changes were obtained or the values mean roughness profile ( Ra) decreased slightly in Ra values after the natural inactivation process.

Process for immobilizing radioactive boric acid liquid wastes

DOEpatents

Greenhalgh, Wilbur O.

1986-01-01

A method of immobilizing boric acid liquid wastes containing radionuclides by neutralizing the solution and evaporating the resulting precipitate to near dryness. The dry residue is then fused into a reduced volume, insoluble, inert, solid form containing substantially all the radionuclides.

External auditory canal stenosis due to the use of powdered boric acid.

PubMed

Dündar, Riza; Soy, Fatih Kemal; Kulduk, Erkan; Muluk, Nuray Bayar; Cingi, Cemal

2014-09-01

Acquired stenosis of the external auditory canal (EAC) may occur because of chronic external otitis, recurrent chronic catarrhal otitis media associated with tympanic membrane perforation, chronic dermatitis, tumors, and trauma. Stenosis occurs generally at the one-third bone part of the external auditory canal. In this article, we present 3 cases of acquired EAC stenosis due to the previous powdered boric acid application. Besides the presentation of surgical intervetions in these cases, we want to notify the physicians not to use or carefully use powdered boric acid because of the complication of EAC stenosis.

The improvement of the energy resolution in epi-thermal neutron region of Bonner sphere using boric acid water solution moderator.

PubMed

Ueda, H; Tanaka, H; Sakurai, Y

2015-10-01

Bonner sphere is useful to evaluate the neutron spectrum in detail. We are improving the energy resolution in epi-thermal neutron region of Bonner sphere, using boric acid water solution as a moderator. Its response function peak is narrower than that for polyethylene moderator and the improvement of the resolution is expected. The resolutions between polyethylene moderator and boric acid water solution moderator were compared by simulation calculation. Also the influence in the uncertainty of Bonner sphere configuration to spectrum estimation was simulated. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sub-lethal exposure of cockroaches to boric acid pesticide contributes to increased Bla g 2 excretion.

PubMed

Zhang, Y C; Perzanowski, M S; Chew, G L

2005-07-01

Several epidemiology studies have found an increase in the major cockroach allergen Bla g 2 with reported pesticide use. Our aim was to investigate the effect on the excretion of Bla g 1 and Bla g 2 allergens by cockroaches exposed to sub-lethal doses of the pesticides, boric acid and hydramethylnon gel. German cockroaches in separate colonies were fed either boric acid or hydramethylnon gel at concentrations of 0.2, 0.1 and 0.01% in their water supply over a 2 week period. Ten colonies were exposed to each treatment concentration. Bla g 1 and Bla g 2 in fecal pellets were measured by ELISA. Cockroaches exposed to boric acid excreted fecal pellets with significantly higher concentrations of Bla g 2 (35,400 U/g) than did controls (12,700 U/g) (P = 0.001). Bla g 1 concentrations were not significantly different. There was no difference in either Bla g 1 or Bla g 2 concentrations between cockroaches that ingested hydramethylnon gel and those in the controls colonies. The application of boric acid, a common pesticide, appears to paradoxically increase the production of Bla g 2, a major allergen, by the surviving cockroaches. This may have important implications in avoidance strategies.

Boric acid-enhanced embedding medium for cryomicrotomy.

PubMed

Lim, Jin Ik; Park, Hun-Kuk

2012-05-01

A polyvinyl alcohol (PVA)/polyethylene glycol (PEG)-based resin is commonly used as a cryoembedding medium for the histological analysis of frozen tissue sections. However, it is not easy to obtain sufficient numbers of satisfactory reproducible sections owing to the differences between the mechanical properties of the medium and embedded tissue and the low cohesive force of the medium. We describe a modified PVA-based cryoembedding medium, composed of PVA (10wt% and 15wt%) with the addition of boric acid (from 0 to 5wt%), that can improve the sectioning properties and efficiency of frozen tissue for histological analysis. The amount of load under the same compressive displacement as well as cohesive force increased with increasing boric acid and PVA contents. 15wt% PVA and 3wt% boric acid was determined as an optimal composition for cryoembedding material based on the sectioning efficiency measured by the numbers of unimpaired sectioned slices and the amount of load under the same compressive displacement test. On the basis of the results of routine hematoxylin and eosin staining of cryosections of tissue embedded in a medium with 3wt% boric acid and PVA, it was concluded that the modified PVA cryoembedding medium can improve the efficiency of cryosectioning for subsequent histological or histochemical analysis of various tissues. Copyright © 2011 Elsevier GmbH. All rights reserved.

FLUCONAZOLE AND BORIC ACID FOR TREATMENT OF VAGINAL CANDIDIASIS--NEW WORDS ABOUT OLD ISSUE.

PubMed

Khameneie, K M; Arianpour, N; Roozegar, R; Aklamli, M; Amiri, M M

2013-04-01

To compare boric acid as an effective treatment for VVC compared to fluconazole. We also studied the efficiency of these drugs in preventing recurrence of VVC. A cross sectional, randomized, double-blind study. Gynaecology clinic of Imam Reza hospital, Tehran - Iran Women with signs and symptoms related to Vulvo Vaginal Candidiasis. Seventy five patients out of total 150 patients with signs and symptoms related to Vulvo Vaginal Candidiasis were treatedwith boric acidpowder everynight for a week and the remaining 75 patients received Fluconazole. The cure rate in first group was 46.7% but the cure rate in second group was 37.3%. The difference was not statistically significant (P>0.3). Difference between the efficacy of the two drugs was not significant either (P=0.47). The recurrence rate among patients in first group was 35% while it was 32% in second group. Their difference was not statistically significant (P=0.54). According to our findings, treatment of vaginal candidiasis with boric acid is as effective as fluconazole. The availability of boric acid and its relatively low cost suggests it as a safe and effective drug for treatment of candidiasis.

Process for immobilizing radioactive boric acid liquid wastes

DOEpatents

Greenhalgh, W.O.

1984-05-10

Disclosed is a method of immobilizing boric acid liquid wastes containing radionuclides by neutralizing the solution and evaporating the resulting precipitate to near dryness. The dry residue is then fused into a reduced volume, insoluble, inert, solid form containing substantially all the radionuclides.

Contact lens care solutions downregulate membrane-associated mucins 1 and 16 in cultured human corneal epithelial cells and at the rat corneal surface in vivo.

PubMed

Tchedre, Kissaou; Imayasu, Masaki; Hori, Yuichi; Cavanagh, H Dwight

2013-11-01

The purpose of this study was first to evaluate the effect of multipurpose contact lens care solutions (MPSs) on the expression of membrane-associated mucins (MUC1 and MUC16) in SV40-transformed human corneal epithelial (HCE-T) cells and in vivo rat cornea. The second aim of this study was to determine the role of the common MPS additive boric acid in reducing mucin expression and release. The HCE-T cells were exposed to different concentrations of MPS-F, MPS-G, MPS-H, MPS-I, and MPS-J with 100% treatment for 30 minutes and 10% treatment for 24 hours. MUC1 and MUC16 expressions were subsequently analyzed by Western blotting. Wister rats were also subjected to MPS-A, MPS-B, MPS-C, MPS-D, and MPS-E and received phosphate-buffered saline exposure (1 drop in the right eye every 10 minutes for 1 hour). The left eye was used as control. Cornea sections and lysates were used for the immunohistochemical assay of MUC1 and MUC16 expressions. Conditioned media from treated HCE-T cells were also analyzed using Western blotting. The MPSs containing boric acid downregulated MUC1 and MUC16 in the rat cornea, whereas MPSs without boric acid had no effect as demonstrated by the Western blotting and immunohistochemical analysis. Conditioned media from MPS-containing boric acid revealed some trace of MUC16. The clinical use of MPSs containing boric acid that reduce MUC1 and MUC16 availability should be avoided. Additionally, the presence of MUC16 in the conditioned media suggests that boric acid may have enhanced cleavage of MUC16 at the cell membrane surface.

The effect of pregnancy on renal clearance of boron in rats given boric acid orally.

PubMed

Vaziri, N D; Oveisi, F; Culver, B D; Pahl, M V; Andersen, M E; Strong, P L; Murray, F J

2001-04-01

Boric acid (H(3)BO(3)) has been shown to cause developmental abnormalities in the offspring of pregnant rats. Comparative data on the renal clearance of boron (B) in rats and humans, both pregnant and nonpregnant, exposed to boric acid (BA) would reduce uncertainty in interspecies extrapolation from rats to humans. The purpose of this study was to evaluate the effect of pregnancy on the plasma half-life and renal clearance of boron in Sprague-Dawley rats given a single oral dose of boric acid. For the half-life study, nonpregnant and pregnant (gestation day 16) rats were given a single dose of 30 mg/kg of boric acid by gavage, and plasma samples were collected at 2-3 h intervals. The plasma half-life of boron was determined to be 2.9 +/- 0.2 and 3.2 +/- 0.3 h in nonpregnant and pregnant rats, respectively. In the clearance study, nonpregnant and pregnant (GD 16) rats were given a single gavage dose of 0.3, 3, or 30 mg/kg of boric acid. Boron clearance was slightly higher in pregnant rats (3.3 +/- 0.6, 3.2 +/- 0.5, and 3.4 +/- 0.5 ml/min/kg, respectively) compared to nonpregnant rats (3.1 +/- 0.8, 3.0 +/- 0.6, and 3.2 +/- 0.5 ml/min/kg, respectively), but the difference was not statistically significant and not dose-related. Boron clearance was less than creatinine clearance, suggesting tubular reabsorption in both groups. In conclusion, pregnancy did not appear to significantly alter the renal clearance or the plasma half-life of boron in Sprague-Dawley rats under the conditions of this study.

Molecular complexes of alprazolam with carboxylic acids, boric acid, boronic acids, and phenols. Evaluation of supramolecular heterosynthons mediated by a triazole ring.

PubMed

Varughese, Sunil; Azim, Yasser; Desiraju, Gautam R

2010-09-01

A series of molecular complexes, both co-crystals and salts, of a triazole drug-alprazolam-with carboxylic acids, boric acid, boronic acids, and phenols have been analyzed with respect to heterosynthons present in the crystal structures. In all cases, the triazole ring behaves as an efficient hydrogen bond acceptor with the acidic coformers. The hydrogen bond patterns exhibited with aromatic carboxylic acids were found to depend on the nature and position of the substituents. Being a strong acid, 2,6-dihydroxybenzoic acid forms a salt with alprazolam. With aliphatic dicarboxylic acids alprazolam forms hydrates and the water molecules play a central role in synthon formation and crystal packing. The triazole ring makes two distinct heterosynthons in the molecular complex with boric acid. Boronic acids and phenols form consistent hydrogen bond patterns, and these are seemingly independent of the substitutional effects. Boronic acids form noncentrosymmetric cyclic synthons, while phenols form O--H...N hydrogen bonds with the triazole ring.

Body Weight Reducing Effect of Oral Boric Acid Intake

PubMed Central

Aysan, Erhan; Sahin, Fikrettin; Telci, Dilek; Yalvac, Mehmet Emir; Emre, Sinem Hocaoglu; Karaca, Cetin; Muslumanoglu, Mahmut

2011-01-01

Background: Boric acid is widely used in biology, but its body weight reducing effect is not researched. Methods: Twenty mice were divided into two equal groups. Control group mice drank standard tap water, but study group mice drank 0.28mg/250ml boric acid added tap water over five days. Total body weight changes, major organ histopathology, blood biochemistry, urine and feces analyses were compared. Results: Study group mice lost body weight mean 28.1% but in control group no weight loss and also weight gained mean 0.09% (p<0.001). Total drinking water and urine outputs were not statistically different. Cholesterol, LDL, AST, ALT, LDH, amylase and urobilinogen levels were statistically significantly high in the study group. Other variables were not statistically different. No histopathologic differences were detected in evaluations of all resected major organs. Conclusion: Low dose oral boric acid intake cause serious body weight reduction. Blood and urine analyses support high glucose, lipid and middle protein catabolisms, but the mechanism is unclear. PMID:22135611

Body weight reducing effect of oral boric acid intake.

PubMed

Aysan, Erhan; Sahin, Fikrettin; Telci, Dilek; Yalvac, Mehmet Emir; Emre, Sinem Hocaoglu; Karaca, Cetin; Muslumanoglu, Mahmut

2011-01-01

Boric acid is widely used in biology, but its body weight reducing effect is not researched. Twenty mice were divided into two equal groups. Control group mice drank standard tap water, but study group mice drank 0.28mg/250ml boric acid added tap water over five days. Total body weight changes, major organ histopathology, blood biochemistry, urine and feces analyses were compared. Study group mice lost body weight mean 28.1% but in control group no weight loss and also weight gained mean 0.09% (p<0.001). Total drinking water and urine outputs were not statistically different. Cholesterol, LDL, AST, ALT, LDH, amylase and urobilinogen levels were statistically significantly high in the study group. Other variables were not statistically different. No histopathologic differences were detected in evaluations of all resected major organs. Low dose oral boric acid intake cause serious body weight reduction. Blood and urine analyses support high glucose, lipid and middle protein catabolisms, but the mechanism is unclear.

The effects of temperature and aeration on the corrosion of A508III low alloy steel in boric acid solutions at 25-95 °C

NASA Astrophysics Data System (ADS)

Xiao, Qian; Lu, Zhanpeng; Chen, Junjie; Yao, Meiyi; Chen, Zhen; Ejaz, Ahsan

2016-11-01

The effects of temperature, solution composition and dissolved oxygen on the corrosion rate and electrochemical behavior of an A508III low alloy steel in boric acid solution with lithium hydroxide at 25-95 °C are investigated. In aerated solutions, increasing the boric acid concentration increases the corrosion rate and the anodic current density. The corrosion rate in deaerated solutions increases with increasing temperature. A corrosion rate peak value is found at approximately 75 °C in aerated solutions. Increasing temperature increases the oxygen diffusion coefficient, decreases the dissolved oxygen concentration, accelerates the hydrogen evolution reaction, and accelerates both the active dissolution and the film forming reactions. Increasing dissolved oxygen concentration does not significantly affect the corrosion rate at 50 and 60 °C, increases the corrosion rate at 70 and 80 °C, and decreases the corrosion rate at 87.5 and 95 °C in a high concentration boric acid solution with lithium hydroxide.

Arabidopsis thaliana NIP7;1: An Anther-Specific Boric Acid Transporter of the Aquaporin Superfamily Regulated by an Unusual Tyrosine in Helix 2 of the Transport Pore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Tian; Choi, Won-Gyu; Baudry, Jerome Y

Plant nodulin-26 intrinsic proteins (NIPs) are members of the aquaporin superfamily that serve as multifunctional transporters of uncharged metabolites. In Arabidopsis thaliana, a specific NIP pore subclass, known as the NIP II proteins, is represented by AtNIP5;1 and AtNIP6;1, which encode channel proteins expressed in roots and leaf nodes, respectively, that participate in the transport of the critical cell wall nutrient boric acid. Modeling of the protein encoded by the AtNIP7;1 gene shows that it is a third member of the NIP II pore subclass in Arabidopsis. However, unlike AtNIP5;1 and AtNIP6;1 proteins, which form constitutive boric acid channels, AtNIP7;1more » forms a channel with an extremely low intrinsic boric acid transport activity. Molecular modeling and molecular dynamics simulations of AtNIP7;1 suggest that a conserved tyrosine residue (Tyr81) located in transmembrane helix 2 adjacent to the aromatic arginine (ar/R) pore selectivity region stabilizes a closed pore conformation through interaction with the canonical Arg220 in ar/R region. Substitution of Tyr81 with a Cys residue, characteristic of established NIP boric acid channels, results in opening of the AtNIP7;1 pore that acquires a robust, transport activity for boric acid as well as other NIP II test solutes (glycerol and urea). Substitution of a Phe for Tyr81 also opens the channel, supporting the prediction from MD simulations that hydrogen bond interaction between the Tyr81 phenol group and the ar/R Arg may contribute to the stabilization of a closed pore state. Expression analyses show that AtNIP7;1 is selectively expressed in developing anther tissues of young floral buds of A. thaliana, principally in developing pollen grains of stage 9 11 anthers. Because boric acid is both an essential nutrient as well as a toxic compound at high concentrations, it is proposed that Tyr81 modulates transport and may provide an additional level of regulation for this transporter in male gametophyte development.« less

Arabidopsis thaliana NIP7;1: an anther-specific boric acid transporter of the aquaporin superfamily regulated by an unusual tyrosine in helix 2 of the transport pore.

PubMed

Li, Tian; Choi, Won-Gyu; Wallace, Ian S; Baudry, Jerome; Roberts, Daniel M

2011-08-09

Plant nodulin-26 intrinsic proteins (NIPs) are members of the aquaporin superfamily that serve as multifunctional transporters of uncharged metabolites. In Arabidopsis thaliana, a specific NIP pore subclass, known as the NIP II proteins, is represented by AtNIP5;1 and AtNIP6;1, which encode channel proteins expressed in roots and leaf nodes, respectively, that participate in the transport of the critical cell wall nutrient boric acid. Modeling of the protein encoded by the AtNIP7;1 gene shows that it is a third member of the NIP II pore subclass in Arabidopsis. However, unlike AtNIP5;1 and AtNIP6;1 proteins, which form constitutive boric acid channels, AtNIP7;1 forms a channel with an extremely low intrinsic boric acid transport activity. Molecular modeling and molecular dynamics simulations of AtNIP7;1 suggest that a conserved tyrosine residue (Tyr81) located in transmembrane helix 2 adjacent to the aromatic arginine (ar/R) pore selectivity region stabilizes a closed pore conformation through interaction with the canonical Arg220 in ar/R region. Substitution of Tyr81 with a Cys residue, characteristic of established NIP boric acid channels, results in opening of the AtNIP7;1 pore that acquires a robust, transport activity for boric acid as well as other NIP II test solutes (glycerol and urea). Substitution of a Phe for Tyr81 also opens the channel, supporting the prediction from MD simulations that hydrogen bond interaction between the Tyr81 phenol group and the ar/R Arg may contribute to the stabilization of a closed pore state. Expression analyses show that AtNIP7;1 is selectively expressed in developing anther tissues of young floral buds of A. thaliana, principally in developing pollen grains of stage 9-11 anthers. Because boric acid is both an essential nutrient as well as a toxic compound at high concentrations, it is proposed that Tyr81 modulates transport and may provide an additional level of regulation for this transporter in male gametophyte development. © 2011 American Chemical Society

Effectiveness of Naturally Occurring Substances Added to Duck Litter in Reducing Emergence and Landing of Adult Musca domestica (Diptera: Muscidae).

PubMed

Lachance, Simon; Shiell, Justine; Guerin, Michele T; Scott-Dupree, Cynthia

2017-02-01

Poultry barns provide an ideal breeding environment for Musca domestica L. (Diptera: Muscidae) owing to the controlled temperatures and litter (manure plus bedding material) accumulation. Management techniques that render the litter less suitable for immature stage development, such as the addition of naturally occurring insecticidal substances, could reduce fly infestations. The effectiveness of acetic, boric, and citric acids; diatomaceous earth; and hydrated lime at restricting female landing and growth of house flies in duck litter was evaluated. Litter treated with 1.9% and 4.7% by weight of acetic or boric acid had significantly lower adult emergence rates compared with the same concentrations of citric acid, diatomaceous earth, hydrated lime, or the untreated control litter. The pH of duck litter treated with acetic or citric acid was significantly reduced and remained significantly lower than the control litter (pH 8.7) for 10 d. Significantly more house flies landed on a house fly-rearing substrate (wheat bran, powdered milk, bloodmeal, water, and yeast) than litter treated with any of the other test substances or the control. The LC50 for boric acid was estimated to be 0.01% by weight, which was lower than that of acetic acid (1.42%). Similarly, the LC90 of boric acid was estimated to be 0.12%, which was lower than that of acetic acid (10.03%). Acetic acid and boric acid have the potential to be incorporated into litter as a pest management tactic to reduce house fly populations in duck production facilities. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Chronic suppurative otitis media due to nontuberculous mycobacteria: A case of successful treatment with topical boric acid.

PubMed

Lefebvre, Marie-Astrid; Quach, Caroline; Daniel, Sam J

2015-07-01

Nontuberculous mycobacteria (NTM) are an increasingly recognized cause of chronic suppurative otitis media in children with tympanostomy tubes. Treatment of this condition is difficult and typically requires a combination of systemic antibiotics and surgical debridement. We present the first case of a 2-year-old male with chronic suppurative otitis media due to NTM who failed systemic antibiotic therapy and was successfully managed with topical boric acid powder. This report highlights the challenges involved in treating this infection, and introduces boric acid as a potentially valuable component of therapy. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Optode Membrane for Determination of Nicotine via Generation of Its Bromoethane Derivative.

PubMed

Choi, M M; Wu, X J; Li, Y R

1999-04-01

A plasticized poly(vinyl chloride) optode membrane incorporated with a valinomycin ionophore, a H(+)-selective chromoionophore (ETH 5294), and a lipophilic potassium tetrakis(4-chlorophenyl)borate was used as a reversible sensing device for the indirect optical determination of nicotine. Nicotine was extracted from a tobacco product (1-5 g) and converted to its bromoethane derivative (NBD(+)Br(-)) by reacting with a solution of bromoethane in ethanol. NBD(+)Br(-) in a solution of 0.05 M boric acid-Borax buffer and 0.2 mM Triton X-100 was extracted into the bulk of the membrane and subsequently caused changes in optical absorption of the sensing layer. The response slope, dynamic working range, detection limit, sensitivity, selectivity, effects of buffer solution and neutral surfactant Triton X-100, and lifetime were discussed in detail. The response was pH dependent. At pH 8.5, the detection range was extended from 0.4 μM to 1 mM. Typical response times (t(95)) of the samples were 2-4 min. The optode method was successfully used to detect nicotine in a tobacco sample from the market (average content 0.720%; RSD 0.044%; n = 11). The interference of K(+) on the optode method can be prevented by the pre-extraction procedure. Malic acid and citrate showed no interferences. The recovery of nicotine as NBD(+) was 84-119% in the range 0.035-5% nicotine. The result was satisfactory compared with an AOAC UV standard method.

Effect of boric acid on oxidative stress in rats with fetal alcohol syndrome

PubMed Central

SOGUT, IBRAHIM; OGLAKCI, AYSEGUL; KARTKAYA, KAZIM; OL, KEVSER KUSAT; SOGUT, MELIS SAVASAN; KANBAK, GUNGOR; INAL, MINE ERDEN

2015-01-01

To the best of our knowledge, this is the first study concerning the effect of boric acid (BA) administration on fetal alcohol syndrome (FAS). In this study, the aim was to investigate prenatal alcohol-induced oxidative stress on the cerebral cortex of newborn rat pups and assess the protective and beneficial effects of BA supplementation on rats with FAS. Pregnant rats were divided into three groups, namely the control, alcohol and alcohol + boric acid groups. As markers of alcohol-induced oxidative stress in the cerebral cortex of the newborn pups, malondialdehyde (MDA), superoxide dismutase (SOD), catalase (CAT) and glutathione peroxidase (GPx) levels were measured. Although the MDA levels in the alcohol group were significantly increased compared with those in the control group (P<0.05), the MDA level in the alcohol + boric acid group was shown to be significantly decreased compared with that in the alcohol group (P<0.01). The CAT activity of the alcohol + boric acid group was significantly higher than that in the alcohol group (P<0.05). The GPx activity in the alcohol group was decreased compared with that in the control group (P<0.05). These results demonstrate that alcohol is capable of triggering damage to membranes of the cerebral cortex of rat pups and BA could be influential in antioxidant mechanisms against oxidative stress resulting from prenatal alcohol exposure. PMID:25667671

Effect of boric acid on oxidative stress in rats with fetal alcohol syndrome.

PubMed

Sogut, Ibrahim; Oglakci, Aysegul; Kartkaya, Kazim; Ol, Kevser Kusat; Sogut, Melis Savasan; Kanbak, Gungor; Inal, Mine Erden

2015-03-01

To the best of our knowledge, this is the first study concerning the effect of boric acid (BA) administration on fetal alcohol syndrome (FAS). In this study, the aim was to investigate prenatal alcohol-induced oxidative stress on the cerebral cortex of newborn rat pups and assess the protective and beneficial effects of BA supplementation on rats with FAS. Pregnant rats were divided into three groups, namely the control, alcohol and alcohol + boric acid groups. As markers of alcohol-induced oxidative stress in the cerebral cortex of the newborn pups, malondialdehyde (MDA), superoxide dismutase (SOD), catalase (CAT) and glutathione peroxidase (GPx) levels were measured. Although the MDA levels in the alcohol group were significantly increased compared with those in the control group (P<0.05), the MDA level in the alcohol + boric acid group was shown to be significantly decreased compared with that in the alcohol group (P<0.01). The CAT activity of the alcohol + boric acid group was significantly higher than that in the alcohol group (P<0.05). The GPx activity in the alcohol group was decreased compared with that in the control group (P<0.05). These results demonstrate that alcohol is capable of triggering damage to membranes of the cerebral cortex of rat pups and BA could be influential in antioxidant mechanisms against oxidative stress resulting from prenatal alcohol exposure.

The Usability of Boric Acid as an Alternative Foaming Agent on the Fabrication of Al/Al2O3 Composite Foams

NASA Astrophysics Data System (ADS)

Yaman, Bilge; Onuklu, Eren; Korpe, Nese O.

2017-09-01

Pure Al and alumina (2, 5, 10 wt.% Al2O3)-added Al composite foams were fabricated through powder metallurgy technique, where boric acid (H3BO3) is employed as a new alternative foaming agent. It is aimed to determine the effects of boric acid on the foaming behavior and cellular structure and also purposed to develop the mechanical properties of Al foams by addition of Al2O3. Al and Al composite foams with porosity fraction in the range of 46-53% were achieved by sintering at 620 °C for 2 h. Cell morphology was characterized using a combination of stereomicroscope equipped with image analyzer and scanning electron microscopy. Microhardness values were measured via using Vickers indentation technique. Quasi-static compression tests were performed at strain rate of 10-3 s-1. Compressive strength and energy absorption of the composite foams enhanced not only by the increasing weight fraction of alumina, but also by the usage of boric acid which leads to formation of boron oxide (B2O3) acting as a binder in obtaining dense cell walls. The results revealed that the boric acid has outstanding potential as foaming agent in the fabrication of Al and Al composite foams by providing improved mechanical properties.

EFFECTS OF HYPERTHERMIA AND BORIC ACID ON SKELETAL DEVELOPMENT IN RAT EMBRYOS

EPA Science Inventory

BACKGROUND: The individual effects of boric acid (BA) and hyperthermia on the development of the axial skeleton have previously been reported. Both cause an increased incidence of axial skeletal defects including a decrease in the total number of ribs and vertebrae. Because of th...

Selective Extraction and Purification of Azaspiracids from Blue Mussels ( Mytilus edulis) Using Boric Acid Gel.

PubMed

Miles, Christopher O; Kilcoyne, Jane; McCarron, Pearse; Giddings, Sabrina D; Waaler, Thor; Rundberget, Thomas; Samdal, Ingunn A; Løvberg, Kjersti E

2018-03-21

Azaspiracids belong to a family of more than 50 polyether toxins originating from marine dinoflagellates such as Azadinium spinosum. All of the azaspiracids reported thus far contain a 21,22-dihydroxy group. Boric acid gel can bind selectively to compounds containing vic-diols or α-hydroxycarboxylic acids via formation of reversible boronate complexes. Here we report use of the gel to selectively capture and release azaspiracids from extracts of blue mussels. Analysis of the extracts and fractions by liquid chromatography-tandem mass spectrometry (LC-MS) showed that this procedure resulted in an excellent cleanup of the azaspiracids in the extract. Analysis by enzyme-linked immunoasorbent assay (ELISA) and LC-MS indicated that most azaspiracid analogues were recovered in good yield by this procedure. The capacity of boric acid gel for azaspiracids was at least 50 μg/g, making this procedure suitable for use in the early stages of preparative purification of azaspiracids. In addition to its potential for concentration of dilute samples, the extensive cleanup provided by boric acid gel fractionation of azaspiracids in mussel samples almost eliminated matrix effects during subsequent LC-MS and could be expected to reduce matrix effects during ELISA analysis. The method may therefore prove useful for quantitative analysis of azaspiracids as part of monitoring programs. Although LC-MS data showed that okadaic acid analogues also bound to the gel, this was much less efficient than for azaspiracids under the conditions used. The boric acid gel methodology is potentially applicable to other important groups of natural toxins containing diols including ciguatoxins, palytoxins, pectenotoxins, tetrodotoxin, trichothecenes, and toxin glycosides.

Inhibition studies of soybean (Glycine max) urease with heavy metals, sodium salts of mineral acids, boric acid, and boronic acids.

PubMed

Kumar, Sandeep; Kayastha, Arvind M

2010-10-01

Various inhibitors were tested for their inhibitory effects on soybean urease. The K(i) values for boric acid, 4-bromophenylboronic acid, butylboronic acid, and phenylboronic acid were 0.20 +/- 0.05 mM, 0.22 +/- 0.04 mM, 1.50 +/- 0.10 mM, and 2.00 +/- 0.11 mM, respectively. The inhibition was competitive type with boric acid and boronic acids. Heavy metal ions including Ag(+), Hg(2+), and Cu(2+) showed strong inhibition on soybean urease, with the silver ion being a potent inhibitor (IC(50) = 2.3 x 10(-8) mM). Time-dependent inhibition studies exhibited biphasic kinetics with all heavy metal ions. Furthermore, inhibition studies with sodium salts of mineral acids (NaF, NaCl, NaNO(3), and Na(2)SO(4)) showed that only F(-) inhibited soybean urease significantly (IC(50) = 2.9 mM). Competitive type of inhibition was observed for this anion with a K(i) value of 1.30 mM.

Voltammetric study of the boric acid-salicylaldehyde-H-acid ternary system and its application to the voltammetric determination of boron.

PubMed

Kajiwara, Mari; Ito, Yoshio N; Miyazaki, Yoshinobu; Fujimori, Takao; Takehara, Kô; Yoshimura, Kazuhisa

2015-02-14

The ternary system of boric acid, salicylaldehyde (SA) and H-acid (HA) was voltammetrically studied from kinetic and equilibrium points of view. The effect of the SA substituents was also studied by using two analogs, 5-fluorosalicylaldehyde (F-SA) and 5-methylsalicylaldehyde (Me-SA). The three cathodic peaks of Azomethine H (AzH), Azomethine H-boric acid complex (AzB), and free SA were observed in the solution containing boric acid, SA and HA. The peak potentials of AzH and SA were shifted to negative potentials with increasing pH, while the peak potential of AzB was pH-independent. This difference indicates that a proton participates in the charge-transfer steps of the AzH and SA reductions, but not in that of the AzB reduction. The formation constants for the AzB complexation were similar among all the examined analogs. In the kinetic study, the reaction rate was higher in an acidic condition for the AzH formation, but in a neutral condition for the AzB formation. The rate constants for the AzB complexes were in the order of F-SA > SA ≈ Me-SA, indicating that the fluoro group accelerates the F-AzB complexation. The AzB complexation mechanism is considered to consist of more than three steps, i.e., the pre-equilibrium of the salicylaldehyde-boric acid complex (SA-B) formation, the nucleophilic attack of HA on SA-B, and the remaining some steps to form AzB. Based on these results, the voltammetric determination method of boron using F-SA was optimized, which allowed the boron concentration to be determined within only 5 min with a 0.03 mg B dm(-3) detection limit.

Effect of pressure on the dissociation constant of boric acid in water and seawater

NASA Astrophysics Data System (ADS)

Millero, Frank J.; Ward, Gary K.; Surdo, Antonio Lo; Huang, Fen

2012-01-01

The sound speeds of boric acid and sodium borate in water and 0.725 m NaCl have been measured from 0 to 50 °C and to near 1 molal. These results have been used to determine the partial molal adiabatic compressibilities of B(OH) 3 and NaB(OH) 4. The partial molal volumes, v¯(i), and compressibilities, κ¯(i), have been used to estimate the changes in the volume (Δ V) and compressibility (Δ κ) for the dissociation of boric acid in water and average seawater (0.725 m NaCl, SA ˜ 35 g/kg) B(OH)3+H2O=H++B(OH)4- where

Boric acid inhibits human prostate cancer cell proliferation.

PubMed

Barranco, Wade T; Eckhert, Curtis D

2004-12-08

The role of boron in biology includes coordinated regulation of gene expression in mixed bacterial populations and the growth and proliferation of higher plants and lower animals. Here we report that boric acid, the dominant form of boron in plasma, inhibits the proliferation of prostate cancer cell lines, DU-145 and LNCaP, in a dose-dependent manner. Non-tumorigenic prostate cell lines, PWR-1E and RWPE-1, and the cancer line PC-3 were also inhibited, but required concentrations higher than observed human blood levels. Studies using DU-145 cells showed that boric acid induced a cell death-independent proliferative inhibition, with little effect on cell cycle stage distribution and mitochondrial function.

Modulated optical phase conjugation in rhodamine 110 doped boric acid glass saturable absorber thin films

NASA Astrophysics Data System (ADS)

Sharma, Ramesh C.; Waigh, Thomas A.; Singh, Jagdish P.

2008-03-01

The optical phase conjugation signal in nearly nondegenerate four wave mixing was studied using a rhodamine 110 doped boric acid glass saturable absorber nonlinear medium. We have demonstrated a narrow band optical filter (2.56±0.15Hz) using an optical phase conjugation signal in the frequency modulation of a weak probe beam in the presence of two strong counterpropagating pump beams in rhodamine 110 doped boric acid glass thin films (10-4m). Both the pump beams and the probe beam are at a wavelength of 488nm (continuous-wave Ar+ laser). The probe beam frequency was detuned with a ramp signal using a piezoelectric transducer mirror.

Boron doping a semiconductor particle

DOEpatents

Stevens, G.D.; Reynolds, J.S.; Brown, L.K.

1998-06-09

A method of boron doping a semiconductor particle using boric acid to obtain a p-type doped particle. Either silicon spheres or silicon powder is mixed with a diluted solution of boric acid having a predetermined concentration. The spheres are dried, with the boron film then being driven into the sphere. A melt procedure mixes the driven boron uniformly throughout the sphere. In the case of silicon powder, the powder is metered out into piles and melted/fused with an optical furnace. Both processes obtain a p-type doped silicon sphere with desired resistivity. Boric acid is not a restricted chemical, is inexpensive, and does not pose any special shipping, handling, or disposal requirements. 2 figs.

Boron doping a semiconductor particle

DOEpatents

Stevens, Gary Don; Reynolds, Jeffrey Scott; Brown, Louanne Kay

1998-06-09

A method (10,30) of boron doping a semiconductor particle using boric acid to obtain a p-type doped particle. Either silicon spheres or silicon powder is mixed with a diluted solution of boric acid having a predetermined concentration. The spheres are dried (16), with the boron film then being driven (18) into the sphere. A melt procedure mixes the driven boron uniformly throughout the sphere. In the case of silicon powder, the powder is metered out (38) into piles and melted/fused (40) with an optical furnace. Both processes obtain a p-type doped silicon sphere with desired resistivity. Boric acid is not a restricted chemical, is inexpensive, and does not pose any special shipping, handling, or disposal requirements.

27 CFR 21.68 - Formula No. 38-F.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Six pounds of either boric acid, N.F., or Polysorbate 80, N.F.; 11/3 pounds of thymol, N.F.; 11/3... of any two or more denaturing materials listed under Formula No. 38-B, plus sufficient boric acid, N..., U.S.P., 2.6 fluid ounces of hydrochloric acid, N.F., and a total of 3 pounds of any two or more of...

27 CFR 21.68 - Formula No. 38-F.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Six pounds of either boric acid, N.F., or Polysorbate 80, N.F.; 11/3 pounds of thymol, N.F.; 11/3... of any two or more denaturing materials listed under Formula No. 38-B, plus sufficient boric acid, N..., U.S.P., 2.6 fluid ounces of hydrochloric acid, N.F., and a total of 3 pounds of any two or more of...

27 CFR 21.68 - Formula No. 38-F.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Six pounds of either boric acid, N.F., or Polysorbate 80, N.F.; 11/3 pounds of thymol, N.F.; 11/3... of any two or more denaturing materials listed under Formula No. 38-B, plus sufficient boric acid, N..., U.S.P., 2.6 fluid ounces of hydrochloric acid, N.F., and a total of 3 pounds of any two or more of...

27 CFR 21.68 - Formula No. 38-F.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Six pounds of either boric acid, N.F., or Polysorbate 80, N.F.; 11/3 pounds of thymol, N.F.; 11/3... of any two or more denaturing materials listed under Formula No. 38-B, plus sufficient boric acid, N..., U.S.P., 2.6 fluid ounces of hydrochloric acid, N.F., and a total of 3 pounds of any two or more of...

27 CFR 21.68 - Formula No. 38-F.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Six pounds of either boric acid, N.F., or Polysorbate 80, N.F.; 11/3 pounds of thymol, N.F.; 11/3... of any two or more denaturing materials listed under Formula No. 38-B, plus sufficient boric acid, N..., U.S.P., 2.6 fluid ounces of hydrochloric acid, N.F., and a total of 3 pounds of any two or more of...

THE IMPACT OF THE MCU LIFE EXTENSION SOLVENT ON DWPF GLASS FORMULATION EFFORTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D; Edwards, T

2011-03-24

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NG-CSSX), a new strip acid, and modified monosodium titanate (mMST) will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing with the next generation solvent and mMST is required to determine the impact of these changes in 512-S operations as well as Chemical Process Cell (CPC), Defense Waste Processing Facility (DWPF) glass formulation activities, and melter operations at DWPF. To support programmatic objectives,more » the downstream impacts of the boric acid strip effluent (SE) to the glass formulation activities and melter operations are considered in this study. More specifically, the impacts of boric acid additions to the projected SB7b operating windows, potential impacts to frit production temperatures, and the potential impact of boron volatility are evaluated. Although various boric acid molarities have been reported and discussed, the baseline flowsheet used to support this assessment was 0.01M boric acid. The results of the paper study assessment indicate that Frit 418 and Frit 418-7D are robust to the implementation of the 0.01M boric acid SE into the SB7b flowsheet (sludge-only or ARP-added). More specifically, the projected operating windows for the nominal SB7b projections remain essentially constant (i.e., 25-43 or 25-44% waste loading (WL)) regardless of the flowsheet options (sludge-only, ARP added, and/or the presence of the new SE). These results indicate that even if SE is not transferred to the Sludge Receipt and Adjustment Tank (SRAT), there would be no need to add boric acid (from a trim tank) to compositionally compensate for the absence of the boric acid SE in either a sludge-only or ARP-added SB7b flowsheet. With respect to boron volatility, the Measurement Acceptability Region (MAR) assessments also suggest that Slurry Mix Evaporator (SME) acceptability decisions would not be different assuming either 100% of the B{sub 2}O{sub 3} from the SE were retained or volatilized. More specifically, the 0.84 wt% B{sub 2}O{sub 3} in the SE is so minor that its presence in the SME analysis does not influence SME acceptability decisions. In fact, using the 100% retention and 100% volatilization composition projections, only minor differences in the predicted properties of the glass product occur with all of the glasses being acceptable over a WL interval of 32-42%. Based on the 0.01M boric acid flowsheet, there is very little difference between Frit 418 and Frit 418-7D (a frit that was compositionally altered to account for the 0.84 wt% B{sub 2}O{sub 3} in the SE) with respect to melt temperature. In fact, when one evaluates the composition of Frit 418-7D, it lies within the current Frit 418 vendor specifications and therefore could have been produced by the vendor targeting the nominal composition of Frit 418.« less

Boric Acid in Kjeldahl Analysis

ERIC Educational Resources Information Center

Cruz, Gregorio

2013-01-01

The use of boric acid in the Kjeldahl determination of nitrogen is a variant of the original method widely applied in many laboratories all over the world. Its use is recommended by control organizations such as ISO, IDF, and EPA because it yields reliable and accurate results. However, the chemical principles the method is based on are not…

Effect of blowing agents on the oxidation resistance of carbon foams prepared from molten sucrose

NASA Astrophysics Data System (ADS)

Narasimman, R.; Prabhakaran, K.

2013-06-01

We have prepared low density carbon foams from molten sucrose using aluminium nitrate and boric acid blowing agents. A comparative study of the oxidation resistance of the carbon foams prepared using the two blowing agents are reported in the present paper. Oxidation of the carbon foams was evaluated under isothermal and non-isothermal conditions in air atmosphere using thermogravimetric analysis (TGA). We have observed that the alumina produced from the aluminium nitrate blowing agent acts as a catalyst whereas the boron produced from boric acid inhibits the oxidation of the carbon foams. The oxidation resistance of carbon foams increases with boron concentration. The oxidation onset temperature for the carbon foams prepared using boric acid blowing agent was nearly 60°C higher than that prepared using aluminium nitrate blowing agent. Carbon foams prepared using aluminium nitrate blowing agent undergoes complete oxidation at temperature less than 700°C. Whereas that prepared using boric acid blowing agent leave ˜ 50 wt.% residue at 900°C. Further evidence is provided by the kinetic analysis of the TGA using Coats-Redfern (CR) equation.

The effect of boric acid on bacterial culture of canine and feline urine.

PubMed

Rowlands, M; Blackwood, L; Mas, A; Cripps, P; Crompton, C; Burrow, R

2011-10-01

To identify the optimal method of submission of canine and feline urine for bacterial culture. Cystocentesis samples from 250 animals (200 dogs, 50 cats) suspected of having urinary tract infections were collected. The reference aliquot, without preservative, was processed on site within 2 hours. Two further aliquots (one without preservative, one with boric acid) were stored at room temperature for up to 7 hours and then posted by guaranteed next day delivery to a commercial laboratory for analysis. Forty-seven of the samples were positive on culture in the reference test. There was no significant difference between reference test results and those of samples posted without preservative (P=0·39), but samples posted in boric acid were significantly less likely to give a positive result (P=0·01). Samples posted without preservative had a sensitivity of 82% and a specificity of 98%; for boric acid, sensitivity was 73% and specificity 99%. Postal urine samples should be submitted to the laboratory in a plain sterile tube. © 2011 British Small Animal Veterinary Association.

Effects of Y/Gd Ratio and Boron Excess on Vacuum Ultraviolet Characteristics and Morphology of (Y,Gd)BO3:Eu Phosphor Particles Prepared by Spray Pyrolysis

NASA Astrophysics Data System (ADS)

Koo, Hye Young; Jung, Dae Soo; Hong, Seung Kwon; Kang, Yun Chan; Jung, Kyeong Youl

2007-06-01

(Y1-xGdx)BO3:Eu (0≤ x≤ 1) phosphor particles were prepared by spray pyrolysis. The optimal amount of boric acid for the high photoluminescence intensity of there particles differed depending on the molar ratio of Y to Gd. With decreasing Y/Gd molar ratio, an increasing amount of excess boric acid was required. The difference in excess quantity of boric acid, which was demanded for the highest photoluminescence intensity according to the Y/Gd ratio, influenced the morphology and mean size of the (Y,Gd)BO3:Eu phosphor particles. The (Y1-xGdx)BO3:Eu (0≤ x≤ 1) phosphor particles had a regular morphology. The mean sizes of the GdBO3:Eu and YBO3:Eu phosphor particles were 1.4 and 1 μm, respectively. The high reactivity of boron and yttrium components produced YBO3:Eu phosphor particles with high photoluminescence intensities by spray pyrolysis using a spray solution with a stoichiometric amount of boric acid.

An ion-pair principle for enantioseparations of basic analytes by nonaqueous capillary electrophoresis using the di-n-butyl L-tartrate-boric acid complex as chiral selector.

PubMed

Wang, Li-Juan; Liu, Xiu-Feng; Lu, Qie-Nan; Yang, Geng-Liang; Chen, Xing-Guo

2013-04-05

A chiral recognition mechanism of ion-pair principle has been proposed in this study. It rationalized the enantioseparations of some basic analytes using the complex of di-n-butyl l-tartrate and boric acid as the chiral selector in methanolic background electrolytes (BGEs) by nonaqueous capillary electrophoresis (NACE). An approach of mass spectrometer (MS) directly confirmed that triethylamine promoted the formation of negatively charged di-n-butyl l-tartrate-boric acid complex chiral counter ion with a complex ratio of 2:1. And the negatively charged counter ion was the real chiral selector in the ion-pair principle enantioseparations. It was assumed that triethylamine should play its role by adjusting the apparent acidity (pH*) of the running buffer to a higher value. Consequently, the effects of various basic electrolytes including inorganic and organic ones on the enantioseparations in NACE were investigated. The results showed that most of the basic electrolytes tested were favorable for the enantioseparations of basic analytes using di-n-butyl l-tartrate-boric acid complex as the chiral ion-pair selector. Copyright © 2013 Elsevier B.V. All rights reserved.

Mitochondrial dysfunction is involved in the toxic activity of boric acid against Saprolegnia.

PubMed

Ali, Shimaa E; Thoen, Even; Evensen, Øystein; Wiik-Nielsen, Jannicke; Gamil, Amr A A; Skaar, Ida

2014-01-01

There has been a significant increase in the incidence of Saprolegnia infections over the past decades, especially after the banning of malachite green. Very often these infections are associated with high economic losses in salmonid farms and hatcheries. The use of boric acid to control the disease has been investigated recently both under in vitro and in vivo conditions, however its possible mode of action against fish pathogenic Saprolegnia is not known. In this study, we have explored the transformation in Saprolegnia spores/hyphae after exposure to boric acid (1 g/L) over a period 4-24 h post treatment. Using transmission electron microscopy (TEM), early changes in Saprolegnia spores were detected. Mitochondrial degeneration was the most obvious sign observed following 4 h treatment in about 20% of randomly selected spores. We also investigated the effect of the treatment on nuclear division, mitochondrial activity and function using confocal laser scanning microscopy (CLSM). Fluorescence microscopy was also used to test the effect of treatment on mitochondrial membrane potential and formation of reactive oxygen species. Additionally, the viability and proliferation of treated spores that correlated to mitochondrial enzymatic activity were tested using an MTS assay. All obtained data pointed towards changes in the mitochondrial structure, membrane potential and enzymatic activity following treatment. We have found that boric acid has no effect on the integrity of membranes of Saprolegnia spores at concentrations tested. It is therefore likely that mitochondrial dysfunction is involved in the toxic activity of boric acid against Saprolegnia spp.

Morphological alterations induced by boric acid and fipronil in the midgut of worker honeybee (Apis mellifera L.) larvae : Morphological alterations in the midgut of A. mellifera.

PubMed

da Silva Cruz, Aline; da Silva-Zacarin, Elaine C M; Bueno, Odair C; Malaspina, Osmar

2010-04-01

Morphological alterations, by means of histological and ultrastructural analysis, have been used to determine the effects of boric acid and fipronil on midgut tissues of honeybee worker, Apis mellifera L. larvae. In order to observe possible morphological alterations in the midgut, two groups of bioassays were performed. In the first one, the larvae were chronically treated with different concentrations of boric acid added to the food (1.0, 2.5 and 7.5 mg/g). In the second group, the larvae were fed with diets containing different concentrations of fipronil (0.1 and 1 microg/g) and compared with control groups without these chemical compounds. In the first bioassay, the larvae were collected on day 3 and in the second bioassay on day 4, when the mortality rate obtained in the toxicological bioassay was not very high. The larval midguts were removed and processed for morphological analyses using a light and transmission electron microscopy. We observed cytoplasmic vacuolizations, with the absence of autophagic vacuoles, and chromatinic compacting in most of the cells in the groups treated with pesticides. The morphological alterations were far greater in the larvae treated with boric acid than in the larvae treated with fipronil. Our data suggest that the midgut cell death observed was in response to boric acid and fipronil action. This study significantly improves the understanding of the toxicological effect of these insecticides from the ecotoxicological perspective.

Effect of boric acid on the properties of Li{sub 2}MnO{sub 3}·LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders prepared by large-scale spray pyrolysis with droplet classifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Young Jun; Choi, Seung Ho; Sim, Chul Min

2012-12-15

Graphical abstract: Display Omitted Highlights: ► Spherical shape Li{sub 2}MnO{sub 3}·LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders are prepared by large-scale spray pyrolysis with droplet classifier. ► Boric acid improves the morphological and electrochemical properties of the composite cathode powders. ► The discharge capacity of the composite cathode powders decreases from 217 to 196 mAh g{sup −1} by the 30th cycle. -- Abstract: Spherically shaped 0.3Li{sub 2}MnO{sub 3}·0.7LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders with filled morphology and narrow size distribution are prepared by large-scale spray pyrolysis. A droplet classification reduces the standard deviation of the size distribution of themore » composite cathode powders. Addition of boric acid improves the morphological properties of the product powders by forming a lithium borate glass material with low melting temperature. The optimum amount of boric acid dissolved in the spray solution is 0.8 wt% of the composite powders. The powders prepared from the spray solution with 0.8 wt% boric acid have a mixed layered crystal structure comprising Li{sub 2}MnO{sub 3} and LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} phases, thus forming a composite compound. The initial charge and discharge capacities of the composite cathode powders prepared from the 0.8 wt% boric acid spray solution are 297 and 217 mAh g{sup −1}, respectively. The discharge capacity of the powders decreases from 217 to 196 mAh g{sup −1} by the 30th cycle, in which the capacity retention is 90%.« less

Enantiomeric separation of seven β-agonists by NACE-Study of chiral selectivity with diacetone-d-mannitol-boric acid complex.

PubMed

Lv, Lili; Wang, Lijuan; Li, Jun; Jiao, Yajun; Gao, Shengnan; Wang, Jiachang; Yan, Hongyuan

2017-10-25

A rapid and effective nonaqueous capillary electrophoresis (NACE)-ultraviolet (UV) method was developed for the enantiomeric separation of seven β-agonists. Diacetone-d-mannitol-boric acid complex was used as a new chiral selector. It was in situ synthesized by the reaction of diacetone-d-mannitol and boric acid in methanol medium containing triethylamine. The effects of diacetone-d-mannitol, boric acid, and triethylamine concentrations on the enantioseparation were carefully investigated. Under the optimized conditions, baseline enantioseparation could be obtained for six of the tested β-agonists within 12min. These results were better than that obtained with d-mannitol-boric acid complex in previous work. 11 B nuclear magnetic resonance ( 11 B NMR) was applied to determine the fraction of boron species and confirm the formation of diacetone-d-mannitol-boric acid complex. Validation of the established NACE method was also carried out according to ICH guidelines. Calibration curves showed good linearity with correlation coefficients (r)≥0.9992 over a certain concentration range for each enantiomer of the tested five β-agonists. The relative standard deviations (RSDs) of intra-day precisions and inter-day precisions of migration times were ≤1.4% (n=6), and ≤6.3% (n=10), respectively. That of peak areas were ≤3.7% (n=6), and ≤5.6% (n=10), respectively. The limits of detection (LODs) and the limits of quantitation (LOQs) based on the signal-to-noise ratios of 3 and 10 were found below 1.25μgmL -1 and 5.00μgmL -1 , respectively. The proposed method was successfully applied to the determination of clenbuterol enantiomers in a multi-component pharmaceutical dosage form called "Ambroxol Hydrochloride and Clenbuterol Hydrochloride Oral Solution". Copyright © 2017 Elsevier B.V. All rights reserved.

Boric acid-phenolic relationships within the Pinus echinata-Pisolithus tinctorius ectomycorrhizal association

Treesearch

Mary Anne Sword; Harold E. Garrett

1994-01-01

At germination, container-grown shortleaf pine seedlings were inoculated with Pisolithus tinctorius (Pers.) Coker & Couch or left uninoculated, and both groups were fertilized semiweekly with a modified Hoagland’s solution supplemented with 0 or 0.4 mM boric acid. After 12, 16 and 24 weeks, seedling root tissue was analyzed for...

The reaction of boric acid with wood in a polystyrene matrix

Treesearch

Yanxin Wang; John Simonsen; Carlos Pascoal Neto; Joao Rocha; Timothy G. Rials; Eric Hart

1996-01-01

The reaction of boric acid with wood fibers in a polymer melt was examined using 13C-nuclear magnetic resonance (NMR), 11B-NMR. differential scanning calorimetry, dynamic mechanical analysis, and component extraction and by the determination of material properties. Samples were blended at 350 and 380°F in a roll mill. The...

Effect of application rate and persistence of boric acid sugar baits applied to plants control of Aedes albopictus

USDA-ARS?s Scientific Manuscript database

The use of toxic baits to kill adult Aedes albopictus (Skuse) mosquitoes is a safe and potentially effective alternative to the use of synthetic chemical insecticides. This study was made to identify effective application rates for boric acid-sugar solution baits sprayed onto plant surfaces and to ...

Effects of Boric Acid on Hox Gene Expression and the Axial Skeleton in the Developing Rat

EPA Science Inventory

Gestational exposure to boric acid (BA) causes reduced incidences of supernumerary ribs and shortening/absence of the 13th rib in the progeny of multiple laboratory species. To further explore this, Sprague-Dawley rats received 500 mg/kg b.i.d. on gestation days (GD) 6, 7, 8, 9,...

Experimental Investigations to Enhance the Tribological Performance of Engine Oil by Using Nano-Boric Acid and Functionalized Multiwalled Carbon Nanotubes: A Comparative Study to Assess Wear in Bronze Alloy

NASA Astrophysics Data System (ADS)

Ajay Vardhaman, B. S.; Amarnath, M.; Ramkumar, J.; Rai, Prabhat K.

2018-04-01

In various mechanical systems, lubricants are generally used to reduce friction and wear; thus, the total energy loss in the mechanical systems can be minimized by the proper enhancement of lubrication properties. In general, friction modifiers and antiwear additives are used to improve the tribological properties of the lubricant. However, the use of these additives has to be phased out due to their fast chemical degradation in their applications and other environmental issues. In recent years, the use of nanoparticles as a potential lubricant additive has received considerable attention because of its excellent mechanical and tribological characteristics. The present work describes the tribological behavior of nano-boric acid, multiwalled carbon nanotubes (MWCNTs), and functionalized multiwalled carbon nanotubes (FMWCNTs) modified with carboxylic acid. These nanoparticles were used to enhance the tribological properties of engine oil (SAE20W40) used to lubricate bronze alloy samples. The performance of these nano-coolants was assessed on a linear reciprocating ball-on-flat tribometer. Results highlight the friction and wear behavior of the nano-boric acid, MWCNTs, and FMWCNTs under three varying parameters such as the effect of nanoparticles concentration, load-carrying capacity, and sliding speed. The addition of nano-boric acid, MWCNTs, and FMWCNTs has significantly improved the tribological properties of the base lubricant. The addition of 0.5 wt.% of nano-boric acid, MWCNTs, and FMWCNTs to the base lubricant has decreased the coefficient of friction by 19.76, 30.55, and 35.65%, respectively, and a significant reduction in wear volume by 55.17, 71.42, and 88.97% was obtained in comparison with base lubricant.

Increased sensitivity and variability of phytotoxicity responses in Arctic soils to a reference toxicant, boric acid.

PubMed

Anaka, Alison; Wickstrom, Mark; Siciliano, Steven Douglas

2008-03-01

Industrial and human activities in the Arctic regions may pose a risk to terrestrial Arctic ecosystem functions. One of the most common terrestrial toxicological end points, primary productivity, typically is assessed using a plant phytotoxicity test. Because of cryoturbation, a soil mixing process common in polar regions, we hypothesized that phytotoxicity test results in Arctic soils would be highly variable compared to other terrestrial ecosystems. The variability associated with phytotoxicity tests was evaluated using Environment Canada's standardized plant toxicity test in three cryoturbated soils from Canada's Arctic exposed to a reference toxicant, boric acid. Northern wheatgrass (Elymus lanceolatus) not only was more sensitive to toxicants in Arctic soils, its response to toxicants was more variable compared to that in temperate soils. The phytotoxicity of boric acid in cryosols was much greater than commonly reported in other soils, with a boric acid concentration of less than 150 microg/g soil needed to inhibit root and shoot growth by 20%. Large variability also was found in the phytotoxicity test results, with coefficients of variation for 10 samples ranging from 160 to 79%. The increased toxicity of boric acid in cryosols and variability in test response was not explained by soil properties. Based on our admittedly limited data set of three different Arctic soils, we recommend that more than 30 samples be taken from each control and potentially impacted area to accurately assess contaminant effects at sites in northern Canada. Such intensive sampling will insure that false-negative results for toxicant impacts in Arctic soils are minimized.

Establishment of Genetically Encoded Biosensors for Cytosolic Boric Acid in Plant Cells.

PubMed

Fukuda, Makiha; Wakuta, Shinji; Kamiyo, Jio; Fujiwara, Toru; Takano, Junpei

2018-06-08

Boron (B) is an essential micronutrient for plants. To maintain B concentration in tissues at appropriate levels, plants use boric acid channels belonging to the NIP subfamily of aquaporins and BOR borate exporters. To regulate B transport, these transporters exhibit different cell-type specific expression, polar localization, and B-dependent post-transcriptional regulation. Here, we describe the development of genetically encoded biosensors for cytosolic boric acid to visualize the spatial distribution and temporal dynamics of B in plant tissues. The biosensors were designed based on the function of the NIP5;1 5'-untranslated region (UTR), which promotes mRNA degradation in response to an elevated cytosolic boric acid concentration. The signal intensities of the biosensor coupled with Venus fluorescent protein and a nuclear localization signal (uNIP5;1-Venus) showed a negative correlation with intracellular B concentrations in cultured tobacco BY-2 cells. When expressed in Arabidopsis thaliana, uNIP5;1-Venus enabled quantification of the B distribution in roots at single-cell resolution. In mature roots, cytosolic B levels in stele were maintained under low-B supply, while those in epidermal, cortical, and endodermal cells were influenced by external B concentrations. Another biosensor coupled with a luciferase protein fused to a destabilization PEST sequence (uNIP5;1-Luc) was used to visualize changes in cytosolic boric acid concentrations. Thus, uNIP5;1-Venus/Luc enables visualization of B transport in various plant cells/tissues. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Adsorption and co-precipitation behavior of arsenate, chromate, selenate and boric acid with synthetic allophane-like materials.

PubMed

Opiso, Einstine; Sato, Tsutomu; Yoneda, Tetsuro

2009-10-15

Pollution caused by boric acid and toxic anions such as As(V), Cr(VI) and Se(VI) is hazardous to human health and environment. The sorption characteristics of these environmentally significant ionic species on allophane-like nanoparticles were investigated in order to determine whether allophane can reduce their mobility in the subsurface environment at circum-neutral pH condition. Solutions containing 100 or 150 mmol of AlCl(3)x6H(2)O were mixed to 100 mmol of Na(4)SiO(4) and the pH were adjusted to 6.4+/-0.3. The mineral suspensions were shaken for 1h and incubated at 80 degrees C for 5 days. Appropriate amounts of As, B, Cr and Se solutions were added separately during and after allophane precipitation. The results showed that As(V) and boric acid can be irreversibly fixed during co-precipitation in addition to surface adsorption. However, Cr(VI) and Se(VI) retention during and after allophane precipitation is mainly controlled by surface adsorption. The structurally fixed As(V) and boric acid were more resistant to release than those bound on the surface. The sorption characteristics of oxyanions and boric acid were also influenced by the final Si/Al molar ratio of allophane in which Al-rich allophane tend to have higher uptake capacity. The overall results of this study have demonstrated the role of allophane-like nanoparticles and the effect of its Si/Al ratio on As, B, Cr and Se transport processes in the subsurface environment.

Mitochondrial Dysfunction Is Involved in the Toxic Activity of Boric Acid against Saprolegnia

PubMed Central

Ali, Shimaa E.; Thoen, Even; Evensen, Øystein; Wiik-Nielsen, Jannicke; Gamil, Amr A. A.; Skaar, Ida

2014-01-01

There has been a significant increase in the incidence of Saprolegnia infections over the past decades, especially after the banning of malachite green. Very often these infections are associated with high economic losses in salmonid farms and hatcheries. The use of boric acid to control the disease has been investigated recently both under in vitro and in vivo conditions, however its possible mode of action against fish pathogenic Saprolegnia is not known. In this study, we have explored the transformation in Saprolegnia spores/hyphae after exposure to boric acid (1 g/L) over a period 4–24 h post treatment. Using transmission electron microscopy (TEM), early changes in Saprolegnia spores were detected. Mitochondrial degeneration was the most obvious sign observed following 4 h treatment in about 20% of randomly selected spores. We also investigated the effect of the treatment on nuclear division, mitochondrial activity and function using confocal laser scanning microscopy (CLSM). Fluorescence microscopy was also used to test the effect of treatment on mitochondrial membrane potential and formation of reactive oxygen species. Additionally, the viability and proliferation of treated spores that correlated to mitochondrial enzymatic activity were tested using an MTS assay. All obtained data pointed towards changes in the mitochondrial structure, membrane potential and enzymatic activity following treatment. We have found that boric acid has no effect on the integrity of membranes of Saprolegnia spores at concentrations tested. It is therefore likely that mitochondrial dysfunction is involved in the toxic activity of boric acid against Saprolegnia spp. PMID:25354209

Boric Acid Reduces the Formation of DNA Double Strand Breaks and Accelerates Wound Healing Process.

PubMed

Tepedelen, Burcu Erbaykent; Soya, Elif; Korkmaz, Mehmet

2016-12-01

Boron is absorbed by the digestive and respiratory system, and it was considered that it is converted to boric acid (BA), which was distributed to all tissues above 90 %. The biochemical essentiality of boron element is caused by boric acid because it affects the activity of several enzymes involved in the metabolism. DNA damage repair mechanisms and oxidative stress regulation is quite important in the transition stage from normal to cancerous cells; thus, this study was conducted to investigate the protective effect of boric acid on DNA damage and wound healing in human epithelial cell line. For this purpose, the amount of DNA damage occurred with irinotecan (CPT-11), etoposide (ETP), doxorubicin (Doxo), and H 2 O 2 was determined by immunofluorescence through phosphorylation of H2AX (Ser139) and pATM (Ser1981) in the absence and presence of BA. Moreover, the effect of BA on wound healing has been investigated in epithelial cells treated with these agents. Our results demonstrated that H2AX (Ser139) foci numbers were significantly decreased in the presence of BA while wound healing was accelerated by BA compared to that in the control and only drug-treated cells. Eventually, the results indicate that BA reduced the formation of DNA double strand breaks caused by agents as well as improving the wound healing process. Therefore, we suggest that boric acid has important therapeutical effectiveness and may be used in the treatment of inflammatory diseases where oxidative stress and wound healing process plays an important role.

DEFECTS IN CERVICAL VERTEBRAE IN BORIC ACID-EXPOSED RAT EMBRYOS ARE ASSOCIATED WITH ANTERIOR SHIFTS OF HOX GENE EXPRESSION DOMAINS

EPA Science Inventory

Defects in cervical vertebrae in boric acid-exposed rat embryos are associated with anterior shifts of hox gene expression domains

Nathalie Wery,1 Michael G. Narotsky,2 Nathalie Pacico,1 Robert J. Kavlock,2 Jacques J. Picard,1 AND Francoise Gofflot,1*
1Unit of Developme...

Chemical mechanism of fire retardance of boric acid on wood

Treesearch

Qingwen Wang; Jian Li; Jerrold E. Winandy

2004-01-01

It is commonly accepted that the fire retardant mechanism of boric acid is a physical mechanism achieved by the formation of a coating or protective layer on the wood surface at high temperature. Although a char-forming catalytic mechanism has been proposed by some researchers, little direct experimental support has been provided for such a chemical mechanism. In this...

Breaking Bad Delirium: Methamphetamine and Boric Acid Toxicity with Hallucinations and Pseudosepsis.

PubMed

Johnson, Kayla; Stollings, Joanna L; Ely, E Wesley

2017-02-01

A 30-year-old patient presented with hallucinations and profound shock. He was initially misdiagnosed as having severe sepsis; once ingestions were considered, he was diagnosed as potentially having arsenic toxicity. The clinical story reveals many instructional lessons that could aid in the evaluation and management of future patients. This man presented with large amounts of blue crystals around his nose and lips from inhaling and eating boric acid (an ant poison) so he could, as he put it, kill the ants "pouring into my mouth and nose and up into my brain." His profound pseudosepsis and sustained delirium were induced by co-ingestion of methamphetamine and a large quantity of boric acid. Delirium is a form of acute brain dysfunction that often is multifactorial in critical illness and, when seen in septic shock, is associated with prolonged mechanical ventilation, increased length of hospital stay, medical costs, higher mortality, and long-term cognitive impairment resembling dementia. Pseudosepsis is a noninfectious condition most commonly seen with ingestions such as salicylate (aspirin) toxicity. This report emphasizes the need to recognize agents that contain boric acid as an etiology of unexplained delirium and profound shock.

Porous carbon-coated silica macroparticles as anode materials for lithium ion batteries: Effect of boric acid

NASA Astrophysics Data System (ADS)

Kim, Young-Kuk; Moon, Jong-Woo; Lee, Jung-Goo; Baek, Youn-Kyung; Hong, Seong-Hyun

2014-12-01

We report carbon-coated porous silica macroparticles (SiO2@C) prepared using polymeric templates and subsequent carbonization with sucrose for improved electrochemical energy storage in lithium-ion batteries (LIBs). In addition, boron is introduced to improve the stability of electrochemical cells by pyrolyzing mixtures of sucrose and boric acid (SiO2@C + B) under inert atmosphere. The initially large surface area of porous SiO2 (SBET ∼ 658 m2 g-1) is reduced to 102 m2 g-1 after carbonization and introduction of boric acid. Surface of both SiO2@C and SiO2@C + B are covered with amorphous carbon. In particular, SiO2@C + B particles containing borosilicate (Si-O-B) phase and B-O bondings and Si-C-O bondings are also detected from the X-ray photoelectron spectra. The SiO2@C + B macroparticles shows high reversible charge capacity up to 503 mAh g-1 after 103 cycles of Li intercalation/de-intercalation although initial capacity was 200 mAh g-1. The improved charge capacity of SiO2@C + B is attributed to formation of advantageous microstructures induced from boric acid.

Boric acid ingestion clinically mimicking toxic epidermal necrolysis.

PubMed

Webb, David V; Stowman, Anne M; Patterson, James W

2013-11-01

The ingestion of large amounts of boric acid, a component of household insecticides, is a rare occurrence, characterized by a diffuse desquamative skin eruption, neutropenia, thrombocytopenia, delirium, acute renal failure and prolonged ileus. A 56-year-old male with a history of multiple previous suicide attempts was witnessed ingesting household roach killer and 4 days later presented to the hospital with lethargy, stiffness and a diffuse erythematous and desquamative eruption with bullous formation. He subsequently developed erythema of both palms as well as alopecia totalis. Histopathology from a right arm shave biopsy revealed a mostly intact epidermis with subtle vacuolar alteration of the basal layer, scattered intraepidermal apoptotic keratinocytes, parakeratosis with alternating layers of orthokeratosis and considerable superficial exfoliation; accompanying dermal changes included vasodilatation and mild perivascular inflammation. This report describes the cutaneous and systemic complications in a rare case of boric acid ingestion. There is little published material on the symptoms and histopathology following boric acid ingestion, but knowledge of this entity is important, both to differentiate it from other causes of desquamative skin rashes and to allow the initiation of appropriate clinical care. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

[Chiral separation of five beta-blockers using di-n-hexyl L-tartrate-boric acid complex as mobile phase additive by reversed-phase liquid chromatography].

PubMed

Yang, Juan; Wang, Lijuan; Guo, Qiaoling; Yang, Gengliang

2012-03-01

A reversed-phase high performance liquid chromatographic (HPLC) method using the di-n-hexyl L-tartrate-boric acid complex as a chiral mobile phase additive was developed for the enantioseparation of five beta-blockers including propranolol, esmolol, metoprolol, bisoprolol and sotalol. In order to obtain a better enantioseparation, the influences of concentrations of di-n-butyl L-tartrate and boric acid, the type, concentration and pH of the buffer, methanol content as well as the molecular structure of analytes were extensively investigated. The separation of the analytes was performed on a Venusil MP-C18 column (250 mm x 4.6 mm, 5 microm). The mobile phase was 15 mmol/L ammonium acetate-methanol containing 60 mmol/L boric acid, 70 mmol/L di-n-hexyl L-tartrate (pH 6.00). The volume ratios of 15 mmol/L ammonium acetate to methanol were 20: 80 for propranolol, esmolol, metoprolol, bisoprolol and 30: 70 for sotalol. The flow rate was 0.5 mL/min and the detection wavelength was set at 214 nm. Under the optimized conditions, baseline enantioseparation was obtained separately for the five pairs of analytes.

Breaking Bad Delirium: Methamphetamine and Boric Acid Toxicity with Hallucinations and Pseudosepsis

PubMed Central

Johnson, Kayla; Stollings, Joanna L.; Ely, E. Wesley

2016-01-01

Objectives A 30-year-old patient presented with hallucinations and profound shock. He was initially misdiagnosed as having severe sepsis; once ingestions were considered, he was diagnosed as potentially having arsenic toxicity. Summary The clinical story reveals many instructional lessons that could aid in the evaluation and management of future patients. This man presented with large amounts of blue crystals around his nose and lips from inhaling and eating boric acid (an ant poison) so he could, as he put it, kill the ants “pouring into my mouth and nose and up into my brain.” His profound pseudosepsis and sustained delirium were induced by co-ingestion of methamphetamine and a large quantity of boric acid. Delirium is a form of acute brain dysfunction that often is multifactorial in critical illness and, when seen in septic shock, is associated with prolonged mechanical ventilation, increased length of hospital stay, medical costs, higher mortality, and long-term cognitive impairment resembling dementia. Pseudosepsis is a noninfectious condition most commonly seen with ingestions such as salicylate (aspirin) toxicity. Conclusions This report emphasizes the need to recognize agents that contain boric acid as an etiology of unexplained delirium and profound shock. PMID:28158885

Boric-Acid-Functional Lanthanide Metal-Organic Frameworks for Selective Ratiometric Fluorescence Detection of Fluoride Ions.

PubMed

Yang, Zhong-Rui; Wang, Man-Man; Wang, Xue-Sheng; Yin, Xue-Bo

2017-02-07

Here, we report that boric acid is used to tune the optical properties of lanthanide metal-organic frameworks (LMOFs) for dual-fluorescence emission and improves the selectivity of LMOFs for the determination of F - ions. The LMOFs are prepared with 5-boronoisophthalic acid (5-bop) and Eu 3+ ions as the precursors. Emission mechanism study indicates that 5-bop is excited with UV photons to produce its triplet state, which then excites Eu 3+ ions for their red emission. This is the general story of the antenna effect, but electron-deficient boric acid decreases the energy transfer efficiency from the triplet state of 5-bop to Eu 3+ ions, so dual emission from both 5-bop and Eu 3+ ions is efficiently excited at the single excitation of 275 nm. Moreover, boric acid is used to identify fluoride specifically as a free accessible site. The ratiometric fluorescent detection of F - ions is validated with the dual emission at single excitation. The LMOFs are very monodisperse, so the determination of aqueous F - ions is easily achieved with high selectivity and a low detection limit (2 μM). For the first time, we reveal that rational selection of functional ligands can improve the sensing efficiency of LMOFs through tuning their optical property and enhancing the selectivity toward targets.

Competitive adsorption of boric acid and chromate onto alumina in aqueous solutions.

PubMed

Demetriou, A; Pashalidis, I

2014-01-01

The competitive adsorption of boric acid and chromate from aqueous solutions by alumina has been investigated by spectrophotometry at pH 8, ionic strength = 0.0, 0.1 and 1.0 M NaClO4, T = 22 ± 3 °C and under normal atmospheric conditions. The experimental data show that addition of excess boric acid in the system leads to the increase of Cr(VI) concentration in solution, indicating the replacement of adsorbed chromate by boron on the alumina surface. Data evaluation results in the determination of the competition reaction constant and the formation constant of the Cr(VI) surface complexes, which are logKCr(VI)-B(III) = -3.5 ± 0.2 and logβ*Cr = 7.6 ± 0.3, respectively.

METHOD AND APPARATUS FOR CONTROLLING DIRECT-CYCLE NEUTRONIC REACTORS

DOEpatents

Reed, G.A.

1961-01-10

A control arrangement is offered for a boiling-water reactor. Boric acid is maintained in the water in the reactor and the amount in the reactor is controlled by continuously removing a portion of the water from the reactor, concentrating the boric acid by evaporating the water therefrom, returning a controlled amount of the acid to the reactor, and simultaneously controlling the water level by varying the rate of spent steam return to the reactor.

Boric acid irrigation as an adjunct to mechanical periodontal therapy in patients with chronic periodontitis: a randomized clinical trial.

PubMed

Sağlam, Mehmet; Arslan, Uğur; Buket Bozkurt, Şerife; Hakki, Sema S

2013-09-01

The purpose of this single-masked, randomized, controlled clinical trial was to evaluate the effects of boric acid irrigation as an adjunct to scaling and root planing (SRP) on clinical and microbiologic parameters and compare this method with chlorhexidine irrigation and SRP alone in patients with chronic periodontitis (CP). Forty-five systemically healthy patients with CP are included in this study. They were divided into three groups: 1) SRP + saline irrigation (C); 2) SRP + chlorhexidine irrigation (CHX); and 3) SRP + boric acid irrigation (B). To determine an ideal concentration of boric acid, a preclinical analysis was conducted. At baseline, 1 month, and 3 months after treatment, clinical measurements, including plaque index (PI), gingival index (GI), probing depth (PD), clinical attachment level (CAL), and bleeding on probing (BOP), were performed, and subgingival plaque samples were taken. Quantitative analysis of Porphyromonas gingivalis (Pg), Tannerella forsythia (Tf), and Treponema denticola (Td) was performed using real-time polymerase chain reaction (PCR) procedures. The concentration of boric acid is 0.75% in this study. All clinical parameters showed statistically significant reduction at all time points compared to baseline in all groups (P <0.001). Whole-mouth PD and CAL reduction was similar in all groups at all time points after treatment (P >0.05). The PD and CAL reductions for moderately deep pockets (PD ≥5 and <7) were greater in the B group compared to other groups between baseline and 1 month (P <0.05). For deep pockets (PD ≥7), reductions were similar in the B and CHX groups (P >0.05). BOP (percentage) was significantly lower in the B group compared with the CHX and C groups in the first month after treatment (P <0.001). GI and PI scores were significantly lower in the B and CHX groups compared with the C group at all time points after treatment (P <0.05). The amounts of Pg, Tf, and Td were significantly reduced in all treatment groups after 1 month (P <0.05). No statistically significant differences were detected among the groups for microbiologic parameters at any time points after treatment (P >0.05). The results of this study suggest that boric acid could be an alternative to chlorhexidine, and it might be more favorable because boric acid was superior in whole-mouth BOP as well as PD and CAL reduction for moderate pockets in early time periods.

Effects of sodium pentaborate pentahydrate exposure on Chlorella vulgaris growth, chlorophyll content, and enzyme activities.

PubMed

Chen, Xueqing; Pei, Yuansheng

2016-10-01

Sodium pentaborate pentahydrate (SPP) is a rare mineral. In this study, SPP was synthesized from boric acid and borax through low-temperature crystallization, and its effects on the growth of the alga, Chlorella vulgaris (C. vulgaris) were assessed. The newly synthesized SPP was characterized by chemical analysis, X-ray diffraction, Fourier-transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis, and differential thermal analysis. The changes in C. vulgaris growth, chlorophyll content, and enzyme activities upon exposure to SPP for 168h were evaluated. Results showed that SPP treatment was detrimental to C. vulgaris growth during the first 24-120h of exposure. The harmful effects, however, diminished over time (168h), even at an effective medium concentration of 226.37mg BL(-1) (the concentration of boron applied per liter of culture medium). A similar trend was observed for chlorophyll content (chlorophyll a and b) and indicated that the photosynthesis of C. vulgaris was not affected and that high levels of SPP may even promote chlorophyll synthesis. Superoxide dismutase and catalase activities of C. vulgaris increased during 24-120h exposure to SPP, but these activities gradually decreased as culture time progressed. In other words, the initial detrimental effects of synthetic SPP on C. vulgaris were temporary and reversible. This research provides a scientific basis for applications of SPP in the environment. Copyright © 2016 Elsevier Inc. All rights reserved.

The influence of metal Mg on micro-morphology and crystallinity of spherical hexagonal boron nitride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Ning, E-mail: zhangning5832@163.com; Liu, Huan; Kan, Hongmin

2015-08-15

Highlights: • The action mechanism of Mg to the synthesis of spherical BN was explored. • The influence of Mg content on the crystallinity of h-BN powders was studied. • Even if not added any template, the spherical h-BN could be prepared. - Abstract: This search used the boric acid and borax as a source of boron, urea as a nitrogen source, Mg as metal catalyst, and thus prepared different micro-morphology and crystallinity hexagonal boron nitride powders under a flowing ammonia atmosphere at a nitriding temperature of 750 °C. The effect of Mg content on the crystallinity and micro-morphology ofmore » hexagonal boron nitride powders was studied, and the Mg action mechanism was explored. Without the added surfactant, the graphitization index (GI) was 6.87, and the diameter of the spherical h-BN was bigger. When the added Mg were 0.1 g, 0.3 g, 0.5 g and 0.7 g, the (GI) decreased to 6.04, 5.67, 4.62 and 4.84, respectively. When the Mg content was higher (0.9 g), GI value increased rapidly, and the crystallinity became bad. When the Mg content was 0.5 g, the dispersion of h-BN powders was at its optimum and refinement apparently, and the crystallinity at its highest.« less

Open-framework gallium borate with boric and metaboric acid molecules inside structural channels showing photocatalysis to water splitting.

PubMed

Gao, Wenliang; Jing, Yan; Yang, Jia; Zhou, Zhengyang; Yang, Dingfeng; Sun, Junliang; Lin, Jianhua; Cong, Rihong; Yang, Tao

2014-03-03

An open-framework gallium borate with intrinsic photocatalytic activities to water splitting has been discovered. Small inorganic molecules, H3BO3 and H3B3O6, are confined inside structural channels by multiple hydrogen bonds. It is the first example to experimentally show the structural template effect of boric acid in flux synthesis.

Vibrational Properties of Bulk Boric Acid 2A and 3T Polymorphs and Their Two-Dimensional Layers: Measurements and Density Functional Theory Calculations.

PubMed

Bezerra da Silva, M; Santos, R C R; Freire, P T C; Caetano, E W S; Freire, V N

2018-02-08

Boric acid (H 3 BO 3 ) is being used effectively nowadays in traps/baits for the management of Aedes aegypti L. and Aedes albopictus Skuse species of mosquitoes, which are the main spreading vectors worldwide for diseases such as malaria, dengue, and zika. Previously, we published results on the structural, electronic, and optical properties of its molecular triclinic H 3 BO 3 -2A and trigonal H 3 BO 3 -3T polymorphs within the framework of density functional theory (DFT). Because of the renewed importance of these materials, the focus of this work is on the vibrational properties of the bulk boric acid 2A and 3T polymorphs. We measured the infrared and Raman spectra of the former, which was accompanied and interpreted through state-of-the-art DFT calculations, supplemented by computations regarding the H 3 BO 3 molecule and two-dimensional layers based on the bulk structures. We identify/assign their normal modes and find vibrational signatures for each polymorph as well as in- and out-of-plane motions and molecular vibrations, unveiling a nice agreement between the DFT level of theory employed and our improved spectroscopic measurements in the wavenumber ranges of 400-2000 cm -1 (infrared) and 0-1500 cm -1 (Raman). We show that a dispersion-corrected DFT functional within the generalized gradient approximation (GGA) can be very accurate in describing the vibrational properties of the boric acid polymorphs. Besides, several issues left open/not clearly resolved in previously published works on the vibrational mode assignments of the bulk and 2D sheets of boric acid are explained satisfactorily. Finally, phonon dispersions and associated densities of states were also evaluated for each polymorph along with their temperature-dependent DFT-calculated entropy, enthalpy, free energy, heat capacity, and Debye temperature. In particular, our DFT calculations suggest a possible way to differentiate the 2A and 3T boric acid polymorphs through Raman spectroscopy and heat capacity measurements.

Microwave-Assisted Condensation Reactions of Acetophenone Derivatives and Activated Methylene Compounds with Aldehydes Catalyzed by Boric Acid under Solvent-Free Conditions.

PubMed

Brun, Elodie; Safer, Abdelmounaim; Carreaux, François; Bourahla, Khadidja; L'helgoua'ch, Jean-Martial; Bazureau, Jean-Pierre; Villalgordo, Jose Manuel

2015-06-23

We here disclosed a new protocol for the condensation of acetophenone derivatives and active methylene compounds with aldehydes in the presence of boric acid under microwave conditions. Implementation of the reaction is simple, healthy and environmentally friendly owing to the use of a non-toxic catalyst coupled to a solvent-free procedure. A large variety of known or novel compounds have thus been prepared, including with substrates bearing acid or base-sensitive functional groups.

Autoinducer-2 detection among commensal oral streptococci is dependent on pH and boric acid.

PubMed

Cuadra, Giancarlo A; Frantellizzi, Ashley J; Gaesser, Kimberly M; Tammariello, Steven P; Ahmed, Anika

2016-07-01

Autoinducer-2, considered a universal signaling molecule, is produced by many species of bacteria; including oral strains. Structurally, autoinducer-2 can exist bound to boron (borated autoinducer-2). Functionally, autoinducer-2 has been linked to important bacterial processes such as virulence and biofilm formation. In order to test production of autoinducer-2 by a given bacterial strain, a bioassay using marine bioluminescent bacteria Vibrio harveyi as a reporter for autoinducer-2 has been designed. We hypothesize that pH adjustment and addition of boron are required for optimal bioluminescence and accurate autoinducer-2 detection. Using this reporter strain we tested autoinducer-2 activity from two oral commensal species, Streptococcus gordonii DL1 and Streptococcus oralis 34. Spent broth was collected and adjusted to pH 7.5 and supplemented with boric acid prior to measuring autoinducer- 2 activity. Results show that low pH inhibits bioluminescence of the reporter strain, but pH 7.5 allows for bioluminescence induction and proper readings of autoinducer-2 activity. Addition of boric acid also has a positive effect on bioluminescence allowing for a more sensitive detection of autoinducer-2 activity. Our data suggests that although autoinducer-2 is present in spent broth, low pH and/or low levels of boric acid become an obstacle for proper autoinducer-2 detection. For proper autoinducer-2 detection, we propose a protocol using this bioassay to include pH adjustment and boric acid addition to spent broth. Studies on autoinducer-2 activity in several bacteria species represent an important area of study as this universal signaling molecule is involved in critical bacterial phenotypes such as virulence and biofilm formation.

Method of repressing the precipitation of calcium fluozirconate

DOEpatents

Newby, B.J.; Rhodes, D.W.

1973-12-25

Boric acid or a borate salt is added to aqueous solutions of fluoride containing radioactive wastes generated during the reprocessing of zirconium alloy nuclear fuels which are to be converted to solid form by calcining in a fluidized bed. The addition of calcium nitrate to the aqueous waste solutions to prevent fluoride volatility during calcination, causes the precipitation of calcium fluozirconate, which tends to form a gel at fluoride concentrations of 3.0 M or greater. The boron containing species introduced into the solution by the addition of the boric acid or borate salt retard the formation of the calcium fluozirconate precipitate and prevent formation of the gel. These boron containing species can be introduced into the solution by the addition of a borate salt but preferably are introduced by the addition of an aqueous solution of boric acid. (Official Gazette)

Superlubricity of a Mixed Aqueous Solution

NASA Astrophysics Data System (ADS)

Ma, Zhi-Zuo; Zhang, Chen-Hui; Luo, Jian-Bin; Lu, Xin-Chun; Wen, Shi-Zhu

2011-05-01

A super-low friction coefficient of 0.0028 is measured under a pressure of 300 MPa when the friction pair (the silicon nitride ball sliding on the silicate glass) is lubricated by the mixed aqueous solution of glycerol and boric acid. The morphorlogies of the hydroxylated glass plate are observed by an atomic force microscope (AFM) in deionized water, glycerol, boric acid and their mixed aqueous solution. Bonding peaks of the retained liquids adhered on the surface of the sliding track are detected by an infrared spectrum apparatus and a Raman spectrum apparatus. The mechanism of the superlubricity of the glycerol and boric acid mixed aqueous solution is discussed. It is deduced that the formation of the lubricant film has enough strength to support higher loads, the hydration effect offering the super lower shear resistance. Key words: superlubricity, water based lubricant, ultra-low friction

Improvement of the performance of the positive electrode in the lead/acid battery by addition of boric acid

NASA Astrophysics Data System (ADS)

Badawy, W. A.; El-Egamy, S. S.

A major disadvantage of the lead/acid battery is the decrease in voltage during operation which makes it unsuitable for systems sensitive to voltage fluctuations. Additives like BaSO 4 or SrSO 4, which are isomorphous to PbSO 4, have been used to overcome this problem. Phosphoric acid and the various phosphates have long been used to improve the performance of the positive electrode of the battery. A beneficial effect of phosphoric acid is to inhibit the rate of the self-discharge reaction of the positive electrode in the lead/acid battery. However, adverse effects of phosphoric acid include capacity loss in the initial cycles, excessive mossing, especially at high H 3PO 4 concentrations, and poor low-temperature performance (decrease in the rate of PbSO 4 oxidation). The effect of boric acid as an additive substituting for H 3PO 4 has been investigated using linear sweep voltammetry, constant potential and impedance measurements. The results show that boric acid markedly improves the kinetics of the {PbO 2}/{PbSO 4} couple and removes the problems encountered during the usage of H 3PO 4.

Boric Acid Corrosion of Concrete Rebar

NASA Astrophysics Data System (ADS)

Pabalan, R. T.; Yang, L.; Chiang, K.–T.

2013-07-01

Borated water leakage through spent fuel pools (SFPs) at pressurized water reactors is a concern because it could cause corrosion of reinforcement steel in the concrete structure and compromise the integrity of the structure. Because corrosion rate of carbon steel in concrete in the presence of boric acid is lacking in published literature and available data are equivocal on the effect of boric acid on rebar corrosion, corrosion rate measurements were conducted in this study using several test methods. Rebar corrosion rates were measured in (i) borated water flowing in a simulated concrete crack, (ii) borated water flowing over a concrete surface, (iii) borated water that has reacted with concrete, and (iv) 2,400 ppm boric acid solutions with pH adjusted to a range of 6.0 to 7.7. The corrosion rates were measured using coupled multielectrode array sensor (CMAS) and linear polarization resistance (LPR) probes, both made using carbon steel. The results indicate that rebar corrosion rates are low (~1 μm/yr or less)when the solution pH is ~7.1 or higher. Below pH ~7.1, the corrosion rate increases with decreasing pH and can reach ~100 μm/yr in solutions with pH less than ~6.7. The threshold pH for carbon steel corrosion in borated solution is between 6.8 and 7.3.

Inhibition of boric acid and sodium borate on the biological activity of microorganisms in an aerobic biofilter.

PubMed

Güneş, Y

2013-01-01

The aim of this work was to study the inhibition effect of boric acid and sodium borate on the treatment of boron containing synthetic wastewater by a down flow aerobic fixed bed biofilm reactor at various chemical oxygen demand (COD)/boron ratios (0.47-20.54). The inhibitory effect of boron on activated sludge was evaluated on the basis of COD removal during the experimental period. The biofilter (effective volume = 2.5 L) was filled with a ring of plastic material inoculated with acclimated activated sludge. The synthetic wastewater composed of glucose, urea, KH2PO4, MgSO4, Fe2 SO4, ZnSO4 x 7H20, KCl, CaCl2, and di-sodium tetraborate decahydrate or boric acid (B = 100-2000 mg L(-1)). The biological treatment of boron containing wastewater resulted in a low treatment removal rate due to the reduced microbial activity as a result of toxic effects of high boron concentrations. The decrease in the COD removal rate by the presence of either boric acid or sodium borate was practically indistinguishable. It was observed from the experiments that about 90-95% of COD removal was possible at high COD/boron ratios.

Aquaglyceroporins Are the Entry Pathway of Boric Acid in Trypanosoma brucei.

PubMed

Marsiccobetre, Sabrina; Rodríguez-Acosta, Alexis; Lang, Florian; Figarella, Katherine; Uzcátegui, Néstor L

2017-05-01

The boron element possesses a range of different effects on living beings. It is essential to beneficial at low concentrations, but toxic at excessive concentrations. Recently, some boron-based compounds have been identified as promising molecules against Trypanosoma brucei, the causative agent of sleeping sickness. However, until now, the boron metabolism and its access route into the parasite remained elusive. The present study addressed the permeability of T. brucei aquaglyceroporins (TbAQPs) for boric acid, the main natural boron species. To this end, the three TbAQPs were expressed in Saccharomyces cerevisiae and Xenopus laevis oocytes. Our findings in both expression systems showed that all three TbAQPs are permeable for boric acid. Especially TbAQP2 is highly permeable for this compound, displaying one of the highest conductances reported for a solute in these channels. Additionally, T. brucei aquaglyceroporin activities were sensitive to pH. Taken together, these results establish that TbAQPs are channels for boric acid and are highly efficient entry pathways for boron into the parasite. Our findings stress the importance of studying the physiological functions of boron and their derivatives in T. brucei, as well as the pharmacological implications of their uptake by trypanosome aquaglyceroporins. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of boric acid on experimental periodontitis and alveolar bone loss in rats.

PubMed

Demirer, Serhat; Kara, M Isa; Erciyas, Kamile; Ozdemir, Hakan; Ozer, Hatice; Ay, Sinan

2012-01-01

The goal of the present study was to evaluate the histopathologic and morphometric effects of systemic boric acid in a rat periodontitis model. Twenty-four Wistar rats were divided into three groups of eight animals each: non-ligated (NL), ligature only (LO), and ligature and treated with boric acid (BA) (3mg/kg per day for 11 days). A 4/0 silk suture was placed in a subgingival position around the mandibular first molars; after 11 days the rats were sacrificed, and changes in alveolar bone levels were measured clinically and tissues were histopathologically examined to assess the differences amongst the study groups. The ratio of presence of inflammatory cell infiltration (ICI) and osteoclast number in the LO group was significantly higher than that of the NL and BA groups (p<0.05). The ratio of presence of osteoblastic activity in the LO group was significantly lower than that of the NL and BA groups (p<0.05). Alveolar bone loss was also significantly higher in the LO group compared to the BA and NL groups (p<005). This study has demonstrated that systemic administration of boric acid reduced periodontal inflammation and alveolar bone loss in periodontal disease in rats. Copyright © 2011 Elsevier Ltd. All rights reserved.

Metalworking and machining fluids

DOEpatents

Erdemir, Ali; Sykora, Frank; Dorbeck, Mark

2010-10-12

Improved boron-based metal working and machining fluids. Boric acid and boron-based additives that, when mixed with certain carrier fluids, such as water, cellulose and/or cellulose derivatives, polyhydric alcohol, polyalkylene glycol, polyvinyl alcohol, starch, dextrin, in solid and/or solvated forms result in improved metalworking and machining of metallic work pieces. Fluids manufactured with boric acid or boron-based additives effectively reduce friction, prevent galling and severe wear problems on cutting and forming tools.

Synthesis and evaluation of aminoborates derived from boric acid and diols for protecting wood against fungal and thermal degradation

Treesearch

George C. Chen

2008-01-01

N-methyl amino catechol borate (1), N-methyl amino-4-methyl catechol borate (2), N-methyl amino-4-t-butyl catechol borate (3), and N-methyl amino-2, 3-naphthyl borate (4) were synthesized by reflux of boric acid with a diol in solvent N,N-dimethyl formamide. The aminoborates were characterized by proton nuclear magnetic resonance spectroscopy, FTIR spectroscopy and...

Method of recycling lithium borate to lithium borohydride through diborane

DOEpatents

Filby, Evan E.

1976-01-01

This invention provides a method for the recycling of lithium borate to lithium borohydride which can be reacted with water to generate hydrogen for utilization as a fuel. The lithium borate by-product of the hydrogen generation reaction is reacted with hydrogen chloride and water to produce boric acid and lithium chloride. The boric acid and lithium chloride are converted to lithium borohydride through a diborane intermediate to complete the recycle scheme.

Effects of sublethal exposure to boric acid sugar bait on adult survival, host-seeking, bloodfeeding behavior, and reproduction of Stegomyia albopicta.

PubMed

Ali, Arshad; Xue, Rui-De; Barnard, Donald R

2006-09-01

Effects of sublethal exposure to 0.1% boric acid sugar bait on adult survival, host-seeking, bloodfeeding behavior, and reproduction of Stegomyia albopicta were studied in the laboratory. Survival of males as well as females was significantly reduced when exposed to the bait, compared to control adults. The host-seeking and bloodfeeding activities in the baited females decreased, but the mean duration of blood engorgement (probing to voluntary withdrawal of proboscis) was not significantly different between the baited and control females. The landing and biting rates (human forearm) were significantly reduced in the baited females compared to nonbaited controls. Fecundity and fertility (based on number of laid eggs per female and percentage egg hatch, respectively) in the baited females were significantly reduced, and ovarian development was retarded. Sublethal exposure to sugar-based boric acid bait has the potential to reduce adult populations of St. albopicta.

A new dual-channel optical signal probe for Cu2+ detection based on morin and boric acid.

PubMed

Wang, Peng; Yuan, Bin Fang; Li, Nian Bing; Luo, Hong Qun

2014-01-01

In this work we utilized the common analytical reagent morin to develop a new a dual-channel, cost-effective, and sensitive method for determination of Cu(2+). It is found that morin is only weakly fluorescent by itself, but forms highly fluorescent complexes with boric acid. Moreover, the fluorescence of complexes of morin with boric acid is quenched linearly by Cu(2+) in a certain concentration range. Under optimum conditions, the fluorescence quenching efficiency was linearly proportional to the concentration of cupric ions in the range of 0.5-25 μM with high sensitivity, and the detection limit for Cu(2+) was 0.38 μM. The linear range was 1-25 μM determined by spectrophotometry, and the detection limit for cupric ions was 0.8 μM. Furthermore, the mechanism of sensitive fluorescence quenching response of morin to Cu(2+) is discussed.

The histopathological and morphometric investigation of the effects of systemically administered boric acid on alveolar bone loss in ligature-induced periodontitis in diabetic rats.

PubMed

Balci Yuce, Hatice; Toker, Hulya; Goze, Fahrettin

2014-11-01

The purpose of this study was to evaluate the effects of systemically administered boric acid on alveolar bone loss, histopathological changes and oxidant/antioxidant status in ligature-induced periodontitis in diabetic rats. Forty-four Wistar rats were divided into six experimental groups: (1) non-ligated (NL, n = 6) group, (2) ligature only (LO, n = 6) group, (3) Streptozotocin only (STZ, n = 8) group, (4) STZ and ligature (STZ+LO, n = 8) group, (5) STZ, ligature and systemic administration of 15 mg/kg/day boric acid for 15 days (BA15, n = 8) group and (6) STZ, ligature and systemic administration of 30 mg/kg/day boric acid for 15 days (BA30, n = 8) group. Diabetes mellitus was induced by 60 mg/kg streptozotocin. Silk ligatures were placed at the gingival margin of lower first molars of the mandibular quadrant. The study duration was 15 days after diabetes induction and the animals were sacrificed at the end of this period. Changes in alveolar bone levels were clinically measured and tissues were histopathologically examined. Serum total antioxidant status (TAS), total oxidant status (TOS), calcium (Ca) and magnesium (Mg) levels and oxidative stress index (OSI) were evaluated. Primary outcome was alveolar bone loss. Seconder outcome (osteoblast number) was also measured. At the end of 15 days, the alveolar bone loss was significantly higher in the STZ+LO group compared to the other groups (p < 0.05). There was no significant difference in alveolar bone loss between the STZ+LO 15 mg/kg boric acid and STZ+LO 30 mg/kg boric acid groups (p > 0.05). Systemically administered boric acid significantly decreased alveolar bone loss compared to the STZ+LO group (p < 0.05). The osteoblast number in the BA30 group was significantly higher than those of the NL, STZ and STZ+LO groups (p < 0.05). Inflammatory cell infiltration was significantly higher in the STZ+LO group the other groups (p < 0.05). Serum TAS levels were significantly higher in the NL and LO groups than the other groups (p < 0.05). The differences in TOS levels were not found to be significant among all the groups (p > 0.05). The OSI values of the BA30 group were significantly lower than the STZ+LO group (p < 0.05). Also, the differences in serum calcium and magnesium levels were insignificant among the all groups (p > 0.05). Within the limits of this study, it can be suggested that BA, when administered systemically, may reduce alveolar bone loss in the diabetic rat model.

Comparison of Boric Acid and Combination Drug of Polymyxin, Neomycin and Hydrocortisone (polymyxin NH) in the Treatment of Acute Otitis Externa.

PubMed

Amani, Soroush; Moeini, Mohammad

2016-07-01

Acute otitis externa is an inflammation of the external auditory canal known as "swimmer's ear". Direct costs including medical treatment, painkillers, antibiotics, steroids or both and indirect costs are also remarkable. The aim of this study was to compare the effect of boric acid and polymyxin, neomycin and hydrocortisone composition in the treatment of acute otitis externa. This randomized clinical trial was carried out on 80 patients aged more than 17-year-old who were referred to Kashani hospital clinic with a diagnosis of acute otitis externa by otolaryngologist. The patients were randomly allocated to two groups (A: Boric acid and B: polymyxin NH ear drops) and Painkiller was prescribed and administered orally for all patients and in the presence of fever, cellulitis around the ears and neck adenopathy, broad-spectrum systemic antibiotics were used besides topical treatment. Symptoms of patients who were evaluated by a physician includes pain, discharge from the ear, swelling of the ear canal, auricle swelling, tenderness, and ear itching. In addition, pain was evaluated in patients and was recorded by Macgill Pain Questionnaire, in the first, third, seventh and tenth days. Results showed that itching on third day (p=0.007) and swelling of the ear canal in the examination of the third day (p=0.006) and the seventh day (p=0.001) in the polymyxin NH group was more than those of boric acid group. Overall mean pain based on McGill questionnaire was 11.10±1.49 in boric acid group in the examination on the first day and was 4.05±0.22 in the examination on the tenth day and in the polymyxin NH group, it was 10.9±0.99 on the first day and 4.20±0.40 on the tenth day. In both groups, pain relief was the same and there was no significant difference between two groups (p=0.075). The findings of this study showed slight differences in the effectiveness of the boric acid drug and combination of polymyxin, neomycin and hydrocortisone in the treatment of patients with acute otitis externa that is of clinical significance.

Comparison of Boric Acid and Combination Drug of Polymyxin, Neomycin and Hydrocortisone (polymyxin NH) in the Treatment of Acute Otitis Externa

PubMed Central

Moeini, Mohammad

2016-01-01

Introduction Acute otitis externa is an inflammation of the external auditory canal known as "swimmer’s ear". Direct costs including medical treatment, painkillers, antibiotics, steroids or both and indirect costs are also remarkable. Aim The aim of this study was to compare the effect of boric acid and polymyxin, neomycin and hydrocortisone composition in the treatment of acute otitis externa. Materials and Methods This randomized clinical trial was carried out on 80 patients aged more than 17-year-old who were referred to Kashani hospital clinic with a diagnosis of acute otitis externa by otolaryngologist. The patients were randomly allocated to two groups (A: Boric acid and B: polymyxin NH ear drops) and Painkiller was prescribed and administered orally for all patients and in the presence of fever, cellulitis around the ears and neck adenopathy, broad-spectrum systemic antibiotics were used besides topical treatment. Symptoms of patients who were evaluated by a physician includes pain, discharge from the ear, swelling of the ear canal, auricle swelling, tenderness, and ear itching. In addition, pain was evaluated in patients and was recorded by Macgill Pain Questionnaire, in the first, third, seventh and tenth days. Results Results showed that itching on third day (p=0.007) and swelling of the ear canal in the examination of the third day (p=0.006) and the seventh day (p=0.001) in the polymyxin NH group was more than those of boric acid group. Overall mean pain based on McGill questionnaire was 11.10±1.49 in boric acid group in the examination on the first day and was 4.05±0.22 in the examination on the tenth day and in the polymyxin NH group, it was 10.9±0.99 on the first day and 4.20±0.40 on the tenth day. In both groups, pain relief was the same and there was no significant difference between two groups (p=0.075). Conclusion The findings of this study showed slight differences in the effectiveness of the boric acid drug and combination of polymyxin, neomycin and hydrocortisone in the treatment of patients with acute otitis externa that is of clinical significance. PMID:27630871

Permeability of boric acid across lipid bilayers and factors affecting it.

PubMed

Dordas, C; Brown, P H

2000-05-15

Boron enters plant roots as undissociated boric acid (H(3)BO(3)). Significant differences in B uptake are frequently observed even when plants are grown under identical conditions. It has been theorized that these differences reflect species differences in permeability coefficient of H(3)BO(3) across plasma membrane. The permeability coefficient of boric acid however, has not been experimentally determined across any artificial or plant membrane. In the experiments described here the permeability coefficient of boric acid in liposomes made of phosphatidylcholine was 4.9x10(-6) cm sec(-1), which is in good agreement with the theoretical value. The permeability coefficient varied from 7x10(-6) to 9.5x10(-9) cm sec(-1) with changes in sterols (cholesterol), the type of phospholipid head group, the length of the fatty acyl chain, and the pH of the medium. In this study we also used Arabidopsis thaliana mutants which differ in lipid composition to study the effect of lipid composition on B uptake. The chs1-1 mutant which has lower proportion of sterols shows 30% higher B uptake compared with the wild type, while the act1-1 mutant which has an increased percentage of longer fatty acids, exhibited 35% lower uptake than the wild type. Lipid composition changes in each of the remaining mutants influenced B uptake to various extents. These data suggest that lipid composition of the plasma membrane can affect total B uptake.

Method of recycling lithium borate to lithium borohydride through methyl borate

DOEpatents

Filby, Evan E.

1977-01-01

This invention provides a method for the recycling of lithium borate to lithium borohydride which can be reacted with water to generate hydrogen for utilization as a fuel. The lithium borate by-product of the hydrogen generation reaction is reacted with hydrogen chloride and water to produce boric acid and lithium chloride. The boric acid and lithium chloride are converted to lithium borohydride through a methyl borate intermediate to complete the recycle scheme.

Kinetic and Mechanistic Study of the pH-Dependent Activation (Epoxidation) of Prodrug Treosulfan Including the Reaction Inhibition in a Borate Buffer.

PubMed

Romański, Michał; Ratajczak, Whitney; Główka, Franciszek

2017-07-01

A prodrug treosulfan (T) undergoes a pH-dependent activation to epoxide derivatives. The process seems to involve an intramolecular Williamson reaction (IWR) but clear kinetic evidence is lacking. Moreover, a cis-diol system present in the T structure is expected to promote complexation with boric acid. As a result, the prodrug epoxidation would be inhibited; however, this phenomenon has not been investigated. In this article, the effect of pH on the kinetics of T conversion to its monoepoxide was studied from a mechanistic point of view. Also, the influence of boric acid on the reaction kinetics was examined. The rate constants observed for the activation of T (k obs ) in acetate, phosphate, and carbonate buffers satisfied the equation logk obs  = -7.48 + 0.96 pH. The reaction was inhibited in the excess of boric acid over T, and the k obs decreased with increasing borate buffer concentration. The experimental results were consistent with the inhibition model that included the formation of a tetrahedral, anionic T-boric acid monoester. To conclude, in nonborate buffers, the T activation to (2S,3S)-1,2-epoxybutane-3,4-diol 4-methanesulfonate follows IWR mechanism. A borate buffer changes the reaction kinetics and complicates kinetic analysis. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

PubMed

Brdicka, R

1936-07-20

1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

Electrodeposited Fe-Co films prepared from a citric-acid-based plating bath

NASA Astrophysics Data System (ADS)

Yanai, T.; Uto, H.; Shimokawa, T.; Nakano, M.; Fukunaga, H.; Suzuki, K.

2013-06-01

Electrodeposited Fe-Co films are commonly prepared in a boric-acid-based bath. In this research, we applied citric acid instead of boric acid for the plating of Fe-Co films because boron in the waste bath is restricted by environmental-protection regulations in Japan. We evaluated the effect of citric acid on the magnetic and structural properties of the films. The saturation magnetization of the Fe-Co films slightly increased while the Fe content in the Fe-Co films decreased with increasing citric acid concentration. The lowest coercivity value of 240 A/m was obtained at a citric acid concentration of 100 g/L. The plating bath with this citric acid concentration enabled us to obtain Fe-Co films with high saturation magnetizations and smooth surface morphologies.

Metal cleaner poisoning

MedlinePlus

Metal cleaners contain organic compounds called hydrocarbons, including: 1,2-butylene oxide Boric acid Cocoyl sarcosine Dicarboxylic fatty acid Dimethoxymethane Dodecanedioic acid N-propyl bromide Sodium hydroxide T-butanol

40 CFR 415.270 - Applicability; description of the borax production subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... borax production subcategory. 415.270 Section 415.270 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Borax Production Subcategory § 415.270 Applicability; description of the borax production... borax by the ore-mining process and by the Trona process. ...

The effect of fire retardants on the fire response characteristics of cellulosic materials

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Brauer, D. P.

1978-01-01

The resistance to ignition of fire retardant-treated wood, cotton, and cellulose insulation was studied. The proprietary composition used to treat wood was found to increase resistance to ignition and to reduce smoke toxicity. Cotton treated with boric acid (added by padding on or by vapor phase process) was found to have increased resistance to ignition and decreased smoke toxicity. Boric acid increased the resistance of cellulose insulation to ignition but also slightly increased the smoke toxicity.

Synthesis and evaluation of borates derived from boric acid and diols for the protection of wood against fungal decay and thermal degradation

Treesearch

George C. Chen

2004-01-01

N,N-dimethyl amino carbinol catechol borate(1). N,N-dimethyl amino carbinol-4-methyl catechol borate(2), N,N-dimethyl amino carbinol-4-t- butyl catechol borate(3). N,N-dimethyl amino carbinol-2,3-naphthyl borate 4) were synthesized by refluxing boric acid and diol in DMF(N,N-dimethyl formamide). The borates were characterized by NMR. Wood impregnated with borate 1,2 or...

Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

PubMed

Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

2015-01-01

A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens.

Co-melting technology in resource recycling of sludge derived from stone processing.

PubMed

Hu, Shao-Hua; Hu, Shen-Chih; Fu, Yen-Pei

2012-12-01

Stone processing sludge (SPS) is a by-product of stone-processing wastewater treatment; it is suitable for use as a raw material for making artificial lightweight aggregates (ALWAs). In this study, boric acid was utilized as a flux to lower sintering temperature. The formation of the viscous glassy phase was observed by DTA curve and changes in XRD patterns. Experiments were conducted to find the optimal combination of sintering temperature, sintering time, and boric acid dosage to produce an ALWA of favorable characteristics in terms of water absorption, bulk density, apparent porosity, compressive strength and weight loss to satisfy Taiwan's regulatory requirements for construction and insulation materials. Optimal results gave a sintering temperature of 850 degrees C for 15 min at a boric acid dosage of 15% by weight of SPS. Results for ALWA favorable characteristics were: 0.21% (water absorption), 0.35% (apparent porosity), 1.67 g/cm3 (bulk density), 66.94 MPa (compressive strength), and less than 0.1% (weight loss).

Co-melting technology in resource recycling of sludge derived from stone processing.

PubMed

Hu, Shao-Hua; Hu, Shen-Chih; Fu, Yen-Pei

2012-12-01

Stone processing sludge (SPS) is a by-product of stone-processing wastewater treatment; it is suitable for use as a raw material for making artificial lightweight aggregates (ALWAs). In this study, boric acid was utilized as a flux to lower sintering temperature. The formation of the viscous glassy phase was observed by DTA curve and changes in XRD patterns. Experiments were conducted to find the optimal combination of sintering temperature, sintering time, and boric acid dosage to produce an ALWA of favorable characteristics in terms of water absorption, bulk density, apparent porosity, compressive strength and weight loss to satisfy Taiwan's regulatory requirements for construction and insulation materials. Optimal results gave a sintering temperature of 850 °C for 15 min at a boric acid dosage of 15 % by weight of SPS. Results for ALWA favorable characteristics were: 0.21 % (water absorption), 0.35 %(apparent porosity), 1.67 g/cm3 (bulk density), 66.94 MPa (compressive strength), and less than 0.1% (weight loss). [Box: see text].

Fabrication of Li2TiO3 pebbles using PVA-boric acid reaction for solid breeding materials

NASA Astrophysics Data System (ADS)

Park, Yi-Hyun; Cho, Seungyon; Ahn, Mu-Young

2014-12-01

Lithium metatitanate (Li2TiO3) is a candidate breeding material of the Helium Cooled Ceramic Reflector (HCCR) Test Blanket Module (TBM). The breeding material is used in pebble-bed form to reduce the uncertainty of the interface thermal conductance. In this study, Li2TiO3 pebbles were successfully fabricated by the slurry droplet wetting method using the cross-linking reaction between polyvinyl alcohol (PVA) and boric acid. The effects of fabrication parameters on the shaping of Li2TiO3 green body were investigated. In addition, the basic characteristics of the sintered pebble were also evaluated. The shape of Li2TiO3 green bodies was affected by slurry viscosity, PVA content and boric acid content. The grain size and average crush load of sintered Li2TiO3 pebble were controlled by the sintering time. The boron was completely removed during the final sintering process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauldin, J.K.; Kard, B.M.

Minimum retentions of disodium octaborate tetrahydrate (DOT) needed in slash pine, Pinus elliottii Engelm. variety elliottii, wood to provide maximum protection against 2 species of subterranean termites were determined in choice and no-choice laboratory tests. Efficacy criteria for DOT were greater or equal to 90% termite mortality and equal to or less than 5% loss in weight of treated wooden blocks. For termites fed only DOT-treated wood, 0.10 and 0.30% boric acid equivalent (BAE, percentage of boric acid based on dry weight of wood, assuming all boron is present as boric acid) protected wood from the eastern subterranean termite, Reticulitermesmore » flavipes (Kollar), and Formosan subterranean termite, Coptotermes formosanus Shiraki, respectively. When termites had a choice between treated or nontreated wooden blocks were not in contact with soil or exposed to rain, a BAE of 0.30% protected the wood from naturally occuring Reticulitermes sp. for 18 mo. In wooden structures under constant pressure from subterranean termites, concentrations greater than 0.54% BAE may be required to protect wood, especially against C. formosanus.« less

40 CFR 436.130 - Applicability; description of the borax subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... borax subcategory. 436.130 Section 436.130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Borax Subcategory § 436.130 Applicability; description of the borax subcategory. The provisions of this subpart are applicable to the processing of borate minerals. Borax obtained from brine lakes is regulated...

40 CFR 436.130 - Applicability; description of the borax subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... borax subcategory. 436.130 Section 436.130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Borax Subcategory § 436.130 Applicability; description of the borax subcategory. The provisions of this subpart are applicable to the processing of borate minerals. Borax obtained from brine lakes is regulated...

40 CFR 436.130 - Applicability; description of the borax subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... borax subcategory. 436.130 Section 436.130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Borax Subcategory § 436.130 Applicability; description of the borax subcategory. The provisions of this subpart are applicable to the processing of borate minerals. Borax obtained from brine lakes is regulated...

Effects of Borax on the Reduction of Pre-oxidized Panzhihua Ilmenite

NASA Astrophysics Data System (ADS)

Guo, Yufeng; Zheng, Fuqiang; Jiang, Tao; Chen, Feng; Wang, Shuai; Qiu, Guanzhou

2018-01-01

The effects of borax (sodium borate) on the enhancement reduction of pre-oxidized Panzhihua ilmenite were investigated. The effects of borax on the mineral phase transformation, microstructures, crystal cell parameter, melting point and Mg distribution were studied to reveal the mechanism of enhancement reduction. Under the constant reduction conditions, the borax could reduce the reduction activation energy of pre-oxidized ilmenite. The reduction kinetics analysis indicated that the reduction rate was controlled by interfacial chemical reaction. The reduction activation energy of the pre-oxidized ilmenite with 4% borax was 80.263 kJ/mol, which was 28.585 kJ/mol less than that of the pre-oxidized ilmenite without borax. Borax could eliminate the migration of Mg into the reduced particle center. The crystal cell parameter of the reduced product was increased by adding borax. Borax could improve the growth of dendritic crystals in the pre-oxidized ilmenite.

THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS

PubMed Central

Brdička, R.

1936-01-01

1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions. PMID:19872968

Exposure assessment of boron in Bandırma boric acid production plant.

PubMed

Duydu, Yalçin; Başaran, Nurşen; Bolt, Hermann M

2012-06-01

Boric acid and sodium borates have been considered as being "toxic to reproduction and development", following results of animal studies with high doses. Experimentally, a NOAEL of 17.5mg B/kg-bw/day (corresponds to ∼2020 ng boron/g blood) has been identified for the (male) reproductive effects of boron in a multigenerational study of rats, and a NOAEL for the developmental effects in rats was identified at 9.6 mg B/kg-bw/day (corresponds to 1270 ng boron/g blood). These values are being taken as the basis of current EU safety assessments. The present study was conducted to assess the boron exposure under extreme exposure conditions in a boric acid production plant located in Bandırma, Turkey. The mean blood boron concentrations of low and high exposure groups were 72.94 ± 15.43 (48.46-99.91) and 223.89 ± 60.49 (152.82-454.02)ng/g respectively. The mean blood boron concentration of the high exposure group is still ≈ 6 times lower than the highest no effect level of boron in blood with regard to the developmental effects in rats and ≈ 9 times lower than the highest no effect level of boron in blood with regard to the reprotoxic effects in male rats. In this context, boric acid and sodium borates should not be considered as toxic to reproduction for humans in daily life. Copyright © 2012 Elsevier GmbH. All rights reserved.

Effects of topical oxiconazole and boric acid in alcohol solutions to rat inner ears.

PubMed

Özdemir, Süleyman; Tuncer, Ülkü; Tarkan, Özgür; Akar, Funda; Sürmelioğlu, Özgür

2013-06-01

The aim of this study is to evaluate the ototoxicity of topical oxiconazole and boric acid in alcohol solutions. Prospective controlled animal study. Research laboratory. Fifty adult Wistar albino rats were divided into 5 groups consisting of 10 animals each. The right tympanic membranes were perforated, and baseline and posttreatment distortion product otoacoustic emission (DPOAE) measurements were performed. The solutions were applied through the external ear canal to the middle ear twice a day for 14 days. The rats in group I and group II received 0.1 mL of oxiconazole-containing solution drops and 4% boric acid in alcohol solution drops, respectively. Group III received gentamicin solution (40 mg/mL) (ototoxic control), group IV received saline solution, and group V was followed without any medication. The baseline DPOAE results of the right ears of all animals tested were normal. Animals in groups I, II, IV, and V showed no statistically significant change in the DPOAE amplitudes. The rats in the gentamicin group showed a significant decrease. This study demonstrates that topically used oxiconazole and boric acid in alcohol solutions to the middle ear appear to be safe on the inner ear of rats. The safety of these drugs has not yet been confirmed in humans. Caution should be taken when prescribing these drugs, especially to patients who had tympanic membrane perforation. Ear drops should be chosen more carefully in an external ear infection for patients with tympanic membrane perforation to avoid ototoxicity.

Gypsum crystal size distribution in four continuous flow stirred slurry boric acid reactors in series compared with the batch

NASA Astrophysics Data System (ADS)

Çakal, G. Ö.; Eroğlu, İ.; Özkar, S.

2006-04-01

Colemanite, one of the important boron minerals, is dissolved in aqueous sulfuric acid to produce boric acid. In this reaction, gypsum is obtained as a by-product. Gypsum crystals are in the shape of thin needles. These crystals should be grown to an easily filterable size in order to increase the production yield and purity of boric acid. In this paper, the particle size distributions and the volume-weighted mean diameters of the gypsum crystals obtained in batch and continuous flow systems were compared. Experiments in both batch and continuous reactors were performed at a temperature of 85 °C, a stirring rate of 400 rpm, and the inlet CaO to SO42- molar ratio of 1.0 using colemanite mineral in particle size smaller than 150 μm. The average diameter of the gypsum crystals obtained at 3.5 h from the batch reactor was found to be 37-41 μm. This value for the continuous system at steady state was observed to change between 44-163 μm. The particle size of the gypsum crystals was found to increase with the residence time of the solid in the continuous system.

In vitro activity of bergamot natural essence and furocoumarin-free and distilled extracts, and their associations with boric acid, against clinical yeast isolates.

PubMed

Romano, L; Battaglia, F; Masucci, L; Sanguinetti, M; Posteraro, B; Plotti, G; Zanetti, S; Fadda, G

2005-01-01

There is very little information, to date, on the antifungal activity of bergamot oil. In this study, we investigated the in vitro activity of three bergamot oils (natural essence, furocoumarin-free extract and distilled extract) against clinically relevant Candida species. We studied the two derivatives, components of Italian pharmaceutical products, that are supposed to be less toxic than the essential oil. In vitro susceptibility of 40 clinical isolates of Candida spp. (Candida albicans, n=20; Candida glabrata, n=13; Candida krusei, n=4; Candida tropicalis, n=2; Candida parapsilosis, n=1), associated with symptomatic and asymptomatic vulvovaginal candidiasis, was determined using a modification of the NCCLS M27-A2 broth microdilution method. MICs were evaluated for each of the oils alone and combined with sub-inhibitory concentrations of the well-known antiseptic, boric acid. To boric acid, all isolates had MIC values ranging from 0.094% to 0.187% (w/v). At 24 h readings, the MIC(90 )s (for all isolates) were (v/v): 5% for natural essence of bergamot, 2.5% for the furocoumarin-free extract, and 1.25% for the distilled extract. At the 48 h reading, these values increased to >10%, 5% and 2.5%, respectively. At both readings, MIC(90 )s for all oil+boric acid combinations were significantly lower than corresponding values for the oils alone (P <0.05). These data indicate that bergamot oils are active in vitro against Candida spp., suggesting their potential role for the topical treatment of Candida infections.

Influence of a Boron Precursor on the Growth and Optoelectronic Properties of Electrodeposited Zinc Oxide Thin Film.

PubMed

Tsin, Fabien; Thomere, Angélica; Bris, Arthur Le; Collin, Stéphane; Lincot, Daniel; Rousset, Jean

2016-05-18

Highly transparent and conductive materials are required for many industrial applications. One of the interesting features of ZnO is the possibility to dope it using different elements, hence improving its conductivity. Results concerning the zinc oxide thin films electrodeposited in a zinc perchlorate medium containing a boron precursor are presented in this study. The addition of boron to the electrolyte leads to significant effects on the morphology and crystalline structure as well as an evolution of the optical properties of the material. Varying the concentration of boric acid from 0 to 15 mM strongly improves the compactness of the deposit and increases the band gap from 3.33 to 3.45 eV. Investigations were also conducted to estimate and determine the influence of boric acid on the electrical properties of the ZnO layers. As a result, no doping effect effect by boron was demonstrated. However, the role of boric acid on the material quality has also been proven and discussed. Boric acid strongly contributes to the growth of high quality electrodeposited zinc oxide. The high doping level of the film can be attributed to the perchlorate ions introduced in the bath. Finally, a ZnO layer electrodeposited in a boron rich electrolyte was tested as front contact of a Cu(In, Ga)(S, Se)2 based solar cell. An efficiency of 12.5% was measured with a quite high fill factor (>70%) which confirms the high conductivity of the ZnO thin film.

Effect of borax on immune cell proliferation and sister chromatid exchange in human chromosomes

PubMed Central

Pongsavee, Malinee

2009-01-01

Background Borax is used as a food additive. It becomes toxic when accumulated in the body. It causes vomiting, fatigue and renal failure. Methods The heparinized blood samples from 40 healthy men were studied for the impact of borax toxicity on immune cell proliferation (lymphocyte proliferation) and sister chromatid exchange in human chromosomes. The MTT assay and Sister Chromatid Exchange (SCE) technic were used in this experiment with the borax concentrations of 0.1, 0.15, 0.2, 0.3 and 0.6 mg/ml. Results It showed that the immune cell proliferation (lymphocyte proliferation) was decreased when the concentrations of borax increased. The borax concentration of 0.6 mg/ml had the most effectiveness to the lymphocyte proliferation and had the highest cytotoxicity index (CI). The borax concentrations of 0.15, 0.2, 0.3 and 0.6 mg/ml significantly induced sister chromatid exchange in human chromosomes (P < 0.05). Conclusion Borax had effects on immune cell proliferation (lymphocyte proliferation) and induced sister chromatid exchange in human chromosomes. Toxicity of borax may lead to cellular toxicity and genetic defect in human. PMID:19878537

Central nervous system radiation syndrome in mice from preferential 10B(n, alpha)7Li irradiation of brain vasculature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slatkin, D.N.; Stoner, R.D.; Rosander, K.M.

1988-06-01

Ionizing radiations were directed at the heads of anesthetized mice in doses that evoked the acute central nervous system (CNS) radiation syndrome. Irradiations were done using either a predominantly thermal neutron field at a nuclear reactor after intraperitoneal injection of 10B-enriched boric acid or 250-kilovolt-peak x-rays with and without previous intraperitoneal injection of equivalent unenriched boric acid. Since 10B concentrations were approximately equal to 3-fold higher in blood than in cerebral parenchyma during the reactor irradiations, more radiation from alpha and 7Li particles was absorbed by brain endothelial cells than by brain parenchymal cells. Comparison of the LD50 dose formore » CNS radiation lethality from the reactor experiments with the LD50 dose from the x-ray experiments gives results compatible with morphologic evidence that endothelial cell damage is a major determinant of acute lethality from the CNS radiation syndrome. It was also observed that boric acid is a low linear energy transfer radiation-enhancement agent in vivo.« less

Preparative enantioseparation of propafenone by counter-current chromatography using di-n-butyl L-tartrate combined with boric acid as the chiral selector.

PubMed

Tong, Shengqiang; Shen, Mangmang; Zheng, Ye; Chu, Chu; Li, Xing-Nuo; Yan, Jizhong

2013-09-01

This paper extends the research of the utilization of borate coordination complexes in chiral separation by counter-current chromatography (CCC). Racemic propafenone was successfully enantioseparated by CCC with di-n-butyl l-tartrate combined with boric acid as the chiral selector. The two-phase solvent system was composed of chloroform/ 0.05 mol/L acetate buffer pH 3.4 containing 0.10 mol/L boric acid (1:1, v/v), in which 0.10 mol/L di-n-butyl l-tartrate was added in the organic phase. The influence of factors in the enantioseparation of propafenone were investigated and optimized. A total of 92 mg of racemic propafenone was completely enantioseparated using high-speed CCC in a single run, yielding 40-42 mg of (R)- and (S)-propafenone enantiomers with an HPLC purity over 90-95%. The recovery for propafenone enantiomers from fractions of CCC was in the range of 85-90%. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Boron

MedlinePlus

... form of boron, inside the vagina to treat yeast infections. People also apply boric acid to the ... acid, used inside the vagina, can successfully treat yeast infections (candidiasis), including infections that do not seem ...

40 CFR 436.130 - Applicability; description of the borax subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... borax subcategory. 436.130 Section 436.130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY Borax Subcategory § 436.130 Applicability; description of the borax subcategory. The provisions of this subpart are...

40 CFR 415.270 - Applicability; description of the borax production subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 29 2014-07-01 2012-07-01 true Applicability; description of the borax... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Borax Production Subcategory § 415.270 Applicability; description of the borax production subcategory. The...

40 CFR 415.270 - Applicability; description of the borax production subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the borax... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Borax Production Subcategory § 415.270 Applicability; description of the borax production subcategory. The...

40 CFR 415.270 - Applicability; description of the borax production subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 30 2013-07-01 2012-07-01 true Applicability; description of the borax... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Borax Production Subcategory § 415.270 Applicability; description of the borax production subcategory. The...

40 CFR 415.270 - Applicability; description of the borax production subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the borax... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Borax Production Subcategory § 415.270 Applicability; description of the borax production subcategory. The...

40 CFR 436.130 - Applicability; description of the borax subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... borax subcategory. 436.130 Section 436.130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS MINERAL MINING AND PROCESSING POINT SOURCE CATEGORY Borax Subcategory § 436.130 Applicability; description of the borax subcategory. The provisions of this subpart are...

Toxicity and carcinogenicity studies of boric acid in male and female B6C3F1 mice.

PubMed Central

Dieter, M P

1994-01-01

Toxicity and potential carcinogenicity studies of boric acid were investigated in mice to verify in a second rodent species that this was a noncarcinogenic chemical. Earlier chronic studies in rats indicated boric acid was not a carcinogen. The chemical is nominated for testing because over 200 tons are produced annually, there are multiple uses for the product, and there is potential for widespread human exposure, both orally and dermally. Both sexes of B6C3F1 mice were offered diets mixed with boric acid for 14 days, 13 weeks, or 2 years. Dietary doses used in the acute, 14-day study were 0, 0.62, 1.25, 2.5, 5, and 10%; those in the subchronic, 13-week study were 0, 0.12, 0.25, 0.50, 1, and 2%; and doses in the 2-year, chronic study were 0, 0.25, and 0.50% in the diet. Mortality, clinical signs of toxicity, estimates of food consumption, body weight gain, and histopathologic examination of selected tissues constituted the variables measured. In the 14-day study mortality was proportional to dose and time of exposure in both sexes, occurring in dose groups as low as 2.5% and as early as 7 days of exposure. Body weights were depressed more than 10% below controls in the higher dose groups of both sexes. Mortality in the 13-week study was confined to the two highest dose groups in male mice and to the 2%-dose group in females. Body weight depression from 8 to 23% below those of controls occurred in the 0.50% and higher dose groups of both sexes.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7889889

Preparation of LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphors by a facile precursor method and their luminescent properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xia; Liang, Pan; Huang, Hong-Sheng

2014-04-01

Graphical abstract: LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphor was obtained by calcining the precursor which was synthesized by boric acid melting method. It (a) exhibits much stronger PL intensity than that (b) prepared by conventional solid state reaction method. - Highlights: • A calcining precursor method was used for preparation of LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphor. • Precursor was prepared by boric acid melting method. • The luminescence intensity of LaB{sub 3}O{sub 6}:Eu{sup 3+} was enhanced by the present method. - Abstract: The LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphors were prepared by calcining the precursors which were synthesized by boric acid meltingmore » method using rare earth oxide and boric acid as raw materials, and they were characterized by EDS, XRD, IR, SEM and PL. The influences of reaction temperature for the preparation of precursor and subsequent calcination temperature and time of precursor on the luminescence properties of LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphor were investigated. The results showed that the LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphors with maximum luminescent intensity were obtained by calcining precursor at 1000 °C for 6 h, in which the precursor was prepared at 200 °C for 72 h. Compared with the conventional high temperature solid-state reaction method, the pure LaB{sub 3}O{sub 6}:Eu{sup 3+} phosphor can be obtained at relatively lower calcination temperature by the precursor method and exhibits much stronger emission intensity.« less

OsNIP3;1, a rice boric acid channel, regulates boron distribution and is essential for growth under boron-deficient conditions.

PubMed

Hanaoka, Hideki; Uraguchi, Shimpei; Takano, Junpei; Tanaka, Mayuki; Fujiwara, Toru

2014-06-01

Boron is an essential micronutrient for higher plants. Boron deficiency is an important agricultural issue because it results in loss of yield quality and/or quantity in cereals and other crops. To understand boron transport mechanisms in cereals, we characterized OsNIP3;1, a member of the major intrinsic protein family in rice (Oryza sativa L.), because OsNIP3;1 is the most similar rice gene to the Arabidopsis thaliana boric acid channel genes AtNIP5;1 and AtNIP6;1. Yeast cells expressing OsNIP3;1 imported more boric acid than control cells. GFP-tagged OsNIP3;1 expressed in tobacco BY2 cells was localized to the plasma membrane. The accumulation of OsNIP3;1 transcript increased fivefold in roots within 6 h of the onset of boron starvation, but not in shoots. Promoter-GUS analysis suggested that OsNIP3;1 is expressed mainly in exodermal cells and steles in roots, as well as in cells around the vascular bundles in leaf sheaths and pericycle cells around the xylem in leaf blades. The growth of OsNIP3;1 RNAi plants was impaired under boron limitation. These results indicate that OsNIP3;1 functions as a boric acid channel, and is required for acclimation to boron limitation. Boron distribution among shoot tissues was altered in OsNIP3;1 knockdown plants, especially under boron-deficient conditions. This result demonstrates that OsNIP3;1 regulates boron distribution among shoot tissues, and that the correct boron distribution is crucial for plant growth. © 2014 The Authors The Plant Journal © 2014 John Wiley & Sons Ltd.

Boric acid inhibits alveolar bone loss in rats by affecting RANKL and osteoprotegerin expression.

PubMed

Sağlam, M; Hatipoğlu, M; Köseoğlu, S; Esen, H H; Kelebek, S

2014-08-01

The goal of the present study was to evaluate the effects of systemic boric acid on the levels of expression of RANKL and osteoprotegerin (OPG) and on histopathologic and histometric changes in a rat periodontitis model. Twenty-four Wistar rats were divided into three groups of eight animals each: nonligated (NL); ligature only (LO); and ligature plus treatment with boric acid (BA) (3 mg/kg per day for 11 d). A 4/0 silk suture was placed in a subgingival position around the mandibular right first molars; after 11 d the rats were killed, and alveolar bone loss in the first molars was histometrically determined. Periodontal tissues were examined histopathologically to assess the differences among the study groups. RANKL and OPG were detected immunohistochemically. Alveolar bone loss was significantly higher in the LO group than in the BA and NL groups (p < 0.05). The number of inflammatory infiltrate and osteoclasts in the LO group was significantly higher than that in the NL and BA groups (p < 0.05). The numbers of osteoblasts in LO and BA groups were significantly higher compared with NL group (p < 0.05). There were significantly more RANKL-positive cells in the LO group than in the BA and NL groups (p < 0.05). There was a higher number of OPG-positive cells in the BA group than in the LO and NL groups (p < 0.05). The present study shows that systemic administration of boric acid may reduce alveolar bone loss by affecting the RANKL/OPG balance in periodontal disease in rats. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effects of Local Administration of Boric Acid on Posterolateral Spinal Fusion with Autogenous Bone Grafting in a Rodent Model.

PubMed

Kömürcü, Erkam; Özyalvaçlı, Gülzade; Kaymaz, Burak; Gölge, Umut Hatay; Göksel, Ferdi; Cevizci, Sibel; Adam, Gürhan; Ozden, Raif

2015-09-01

Spinal fusion is among the most frequently applied spinal surgical procedures. The goal of the present study was to evaluate whether the local administration of boric acid (BA) improves spinal fusion in an experimental spinal fusion model in rats. Currently, there is no published data that evaluates the possible positive effects if the local administration of BA on posterolateral spinal fusion. Thirty-two rats were randomly divided into four independent groups: no material was added at the fusion area for group 1; an autogenous morselized corticocancellous bone graft was used for group 2; an autogenous morselized corticocancellous bone graft with boric acid (8.7 mg/kg) for group 3; and only boric acid was placed into the fusion area for group 4. The L4-L6 spinal segments were collected at week 6, and the assessments included radiography, manual palpation, and histomorphometry. A statistically significant difference was determined between the groups with regard to the mean histopathological scores (p = 0.002), and a paired comparison was made with the Mann-Whitney U test to detect the group/groups from which the difference originated. It was determined that only the graft + BA practice increased the histopathological score significantly with regard to the control group (p = 0.002). Whereas, there was no statistically significant difference between the groups in terms of the manual assessment of fusion and radiographic analysis (respectively p = 0.328 and p = 0.196). This preliminary study suggests that BA may clearly be useful as a therapeutic agent in spinal fusion. However, further research is required to show the most effective dosage of BA on spinal fusion, and should indicate whether BA effects spinal fusion in the human body.

40 CFR 721.1730 - Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Poly(oxy-1,2-ethanediyl), α-butyl-Ï... Significant New Uses for Specific Chemical Substances § 721.1730 Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy...) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric...

40 CFR 721.1730 - Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric acid (H3BO3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Poly(oxy-1,2-ethanediyl), α-butyl-Ï... Significant New Uses for Specific Chemical Substances § 721.1730 Poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy...) The chemical substance identified as poly(oxy-1,2-ethanediyl), α-butyl-ω-hydroxy, ester with boric...

The Effect of Time, Temperature and Composition on Boron Carbide Synthesis by Sol-gel Method

NASA Astrophysics Data System (ADS)

Hadian, A. M.; Bigdeloo, J. A.

2008-02-01

To minimize free carbon residue in the boron carbide (B4C) powder, a modified sol-gel process is performed where the starting materials as boric acid and citric acid compositions are adjusted. Because of boron loss in the form of B2O2(g) during the reduction reaction of the stoichiometric starting composition, the final B4C powders contain carbon residues. Thus, an excess H3BO3 is used in the reaction to compensate the loss and to obtain stoichiometric powders. Parameters of production have been determined using x-ray diffraction analysis and particle size analyses. The synthesized B4C powder using an excess boric acid composition shows no trace of carbon.

Direct solid surface fluorescence spectroscopy of standard chemicals and humic acid in ternary system

NASA Astrophysics Data System (ADS)

Mounier, S.; Nicolodelli, G.; Redon, R.; Milori, D. M. B. P.

2017-04-01

The front face fluorescence spectroscopy is often used to quantify chemicals in well-known matrices as it is a rapid and powerful technique, with no sample preparation. However it was not used to investigate extracted organic matter like humic substances. This work aims to fully investigate for the first time front face fluorescence spectroscopy response of a ternary system including boric acid, tryptophan and humic substances, and two binaries system containing quinine sulfate or humic substance in boric acid. Pure chemicals, boric acid, tryptophan, quinine sulfate and humic acid were mixed together in solid pellet at different contents from 0 to 100% in mass. The measurement of excitation emission matrix of fluorescence (3D fluorescence) and laser induced fluorescence were then done in the front face mode. Fluorescence matrices were decomposed using the CP/PARAFAC tools after scattering treatments. Results show that for 3D fluorescence there is no specific component for tryptophan and quinine sulfate, and that humic substances lead to a strong extinction effect for mixture containing quinine sulfate. Laser induced fluorescence gives a very good but non-specific related response for both quinine sulfate and tryptophan. No humic substances fluorescence response was found, but extinction effect is observed as for 3D fluorescence. This effect is stronger for quinine sulfate than for tryptophan. These responses were modeled using a simple absorbance versus emission model.

Boric acid inhibits embryonic histone deacetylases: A suggested mechanism to explain boric acid-related teratogenicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Di Renzo, Francesca; Cappelletti, Graziella; Broccia, Maria L.

2007-04-15

Histone deacetylases (HDAC) control gene expression by changing histonic as well as non histonic protein conformation. HDAC inhibitors (HDACi) are considered to be among the most promising drugs for epigenetic treatment for cancer. Recently a strict relationship between histone hyperacetylation in specific tissues of mouse embryos exposed to two HDACi (valproic acid and trichostatin A) and specific axial skeleton malformations has been demonstrated. The aim of this study is to verify if boric acid (BA), that induces in rodents malformations similar to those valproic acid and trichostatin A-related, acts through similar mechanisms: HDAC inhibition and histone hyperacetylation. Pregnant mice weremore » treated intraperitoneally with a teratogenic dose of BA (1000 mg/kg, day 8 of gestation). Western blot analysis and immunostaining were performed with anti hyperacetylated histone 4 (H4) antibody on embryos explanted 1, 3 or 4 h after treatment and revealed H4 hyperacetylation at the level of somites. HDAC enzyme assay was performed on embryonic nuclear extracts. A significant HDAC inhibition activity (compatible with a mixed type partial inhibition mechanism) was evident with BA. Kinetic analyses indicate that BA modifies substrate affinity by a factor {alpha} = 0.51 and maximum velocity by a factor {beta} = 0.70. This work provides the first evidence for HDAC inhibition by BA and suggests such a molecular mechanism for the induction of BA-related malformations.« less

Method for synthesizing boracities

DOEpatents

Wolf, Gary A [Kennewick, WA

1982-01-01

A method for producing boracites is disclosed in which a solution of divalent metal acetate, boric acid, and halogen acid is evaporated to dryness and the resulting solid is heated in an inert atmosphere under pressure.

Assay of calcium borogluconate veterinary medicines for calcium gluconate, boric acid, phosphorus, and magnesium by using inductively coupled plasma emission spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyons, D.J.; Spann, K.P.

1985-03-01

An inductively coupled plasma spectrometric method is described for the determination of 4 elements (Ca, B, P, and Mg) in calcium borogluconate veterinary medicines. Samples are diluted, acidified, and sprayed directly into the plasma. Reproducibility relative confidence intervals for a single sample assay are +/- 1.4% (calcium), +/- 1.8% (boron), +/- 2.6% (phosphorus), and +/- 1.4% (magnesium). The total element concentrations for each of 4 elements compared favorably with concentrations determined by alternative methods. Formulation estimates of levels of calcium gluconate, boric acid, phosphorus, and magnesium salts can be made from the analytical data.

In situ synthesis of di-n-butyl l-tartrate-boric acid complex chiral selector and its application in chiral microemulsion electrokinetic chromatography.

PubMed

Hu, Shaoqiang; Chen, Yonglei; Zhu, Huadong; Zhu, Jinhua; Yan, Na; Chen, Xingguo

2009-11-06

A novel procedure for in situ assembling a complex chiral selector, di-n-butyl l-tartrate-boric acid complex, by the reaction of di-n-butyl l-tartrate with boric acid in a running buffer was reported and its application in the enantioseparation of beta-blockers and structural related compounds by chiral microemulsion electrokinetic chromatography (MEEKC) has been demonstrated. In order to achieve a good enantioseparation, the effect of dibutyl l-tartrate and sodium tetraborate concentration, surfactant identity and concentration, cosurfactant, buffer pH and composition, organic modifiers, as well as applied voltage and capillary length were investigated. Ten pairs of enantiomers that could not be separated with only dibutyl l-tartrate, obtained good chiral separation using the complex chiral selector; among them, seven pairs could be baseline resolved under optimized experimental conditions. The fixation of chiral centers by the formation of five-membered rings, and being oppositely charged with basic analytes were thought to be the key factors giving the complex chiral selector a superior chiral recognition capability. The effect of the molecular structure of analytes on enantioseparation was discussed in terms of molecular interaction.

Flame retardant finishing of cotton fabric based on synergistic compounds containing boron and nitrogen.

PubMed

Xie, Kongliang; Gao, Aiqin; Zhang, Yongsheng

2013-10-15

Boric acid and compound containing nitrogen, 2,4,6-tri[(2-hydroxy-3-trimethyl-ammonium)propyl]-1,3,5-triazine chloride (Tri-HTAC) were used to finish cotton fabric. The flame retardant properties of the finished cotton fabrics and the synergetic effects of boron and nitrogen elements were investigated and evaluated by limited oxygen index (LOI) method. The mechanism of cross-linking reaction among cotton fiber, Tri-HTAC, and boric acid was discussed by FTIR and element analysis. The thermal stability and surface morphology of the finished cotton fabrics were investigated by thermogravimetric analysis (TGA) and scanning electron microscope (SEM), respectively. The finishing system of the mixture containing boron and nitrogen showed excellent synergistic flame retardancy for cotton fabric. The cotton fabric finished with mixture system had excellent flame retardancy. The LOI value of the treated cotton fabric increased over 27.5. Tri-HTAC could form covalent bonds with cellulose fiber and boric acid. The flame retardant cotton fabric showed a slight decrease in tensile strength and whiteness. The surface morphology of flame retardant cotton fiber was smooth. Copyright © 2013 Elsevier Ltd. All rights reserved.

Boric acid induces cytoplasmic stress granule formation, eIF2α phosphorylation, and ATF4 in prostate DU-145 cells.

PubMed

Henderson, Kimberly A; Kobylewski, Sarah E; Yamada, Kristin E; Eckhert, Curtis D

2015-02-01

Dietary boron intake is associated with reduced prostate and lung cancer risk and increased bone mass. Boron is absorbed and circulated as boric acid (BA) and at physiological concentrations is a reversible competitive inhibitor of cyclic ADP ribose, the endogenous agonist of the ryanodine receptor calcium (Ca(+2)) channel, and lowers endoplasmic reticulum (ER) [Ca(2+)]. Low ER [Ca(2+)] has been reported to induce ER stress and activate the eIF2α/ATF4 pathway. Here we report that treatment of DU-145 prostate cells with physiological levels of BA induces ER stress with the formation of stress granules and mild activation of eIF2α, GRP78/BiP, and ATF4. Mild activation of eIF2α and its downstream transcription factor, ATF4, enables cells to reconfigure gene expression to manage stress conditions and mild activation of ATF4 is also required for the differentiation of osteoblast cells. Our results using physiological levels of boric acid identify the eIF2α/ATF pathway as a plausible mode of action that underpins the reported health effects of dietary boron.

Ototoxicity of boric acid powder in a rat animal model.

PubMed

Salihoglu, Murat; Dogru, Salim; Cesmeci, Enver; Caliskan, Halil; Kurt, Onuralp; Kuçukodaci, Zafer; Gungor, Atila

2017-04-22

Boric acid, which has antiseptic and acidic properties, is used to treat external and middle ear infections. However, we have not found any literature about the effect of boric acid powder on middle ear mucosa and inner ear. The purpose of this study is to investigate possible ototoxic effects of boric acid powder (BAP) on cochlear outer hair cell function and histological changes in middle ear mucosa in a rat animal model. Twenty healthy, mature Wistar albino rats were used in this study. The rats were divided into two groups, Group A and Group B, each of which consisted of 10 rats. Initially, the animals in each group underwent distortion product otoacoustic emissions (DPOAE) testing of their right and left ears. After the first DPOAE test, a surgical microscope was used to make a small perforation in both ears of the rats in each group, and a second DPOAE test was used to measure both ears in all of the rats. BAP was applied to the right middle ear of the rats using tympanic membrane perforation, and the DPOAEs were measured immediately after the BAP application. The histological changes and DPOAEs were evaluated three days later in Group A and 40 days later in Group B. No significant differences were found at all of the DPOAE frequencies. In Group A, mild inflammation of the middle ear mucosa was found on the third day after BAP application. In Group B, BAP caused mild inflammatory changes on the 40th day, which declined over time. Those changes did not lead to significant fibrosis within the mucosa. In rats, BAP causes mild inflammation in middle ear mucosa and it has no ototoxic effects on cochlear outer hair cell function in the inner ear of rats. Copyright © 2017 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

[Estimation of activity of pharmakopeal disinfectants and antiseptics against Gram-negative and Gram-positive bacteria isolated from clinical specimens, drugs and environment].

PubMed

Grzybowska, Wanda; Młynarczyk, Grazyna; Młynarczyk, Andrzej; Bocian, Ewa; Luczak, Mirosław; Tyski, Stefan

2007-01-01

The MIC of nine different disinfectants and antiseptics were determined for the Gram-negative and Gram-positive bacteria. Strains originated from clinical specimens, drugs and environment. A sensitivity was determined against chlorhexidinum digluconate (Gram-negative: 0,625-80 mg/L, Gram-positive: 0,3-10 mg/L), benzalconium chloride (Gram-negative: 2,5-1280 mg/L, Gram-positive: 1,25-20 mg/L), salicilic acid (Gram-negative and Gram-positive: 400-1600 mg/L), benzoic acid (Gram-negative: 800-1600 mg/L, Gram-positive: 400-1 600 mg/L), boric acid (Gram-negative: 800-12 800 mg/L, Gram-positive: 1 600-6400 mg/L), chloramine B (Gram-negative: 1600-6400 mg/L, Gram-positive:800- 6400 mg/L), jodine (Gram-negative: 200-1600 mg/L, Gram-positive: 200-1600 mg/L), etacridine lactate (Gram-negative: 40 do > 20480 mg/L, Gram-positive: 40-1280 mg/L) and resorcine (Gram-negative: 1600-6400 mg/L, Gram-positive: 800-6400 mg/L). Diversified values of MIC for different strains were obtained, especially in the case of benzalconium chloride, etacridine lactate, chlorhexidinum digluconate, boric acid and iodine. Strains isolated from environment were usually more susceptible to examined compounds than clinical strains. The biggest diversification of sensitivity was observed among strains originated from drugs where besides sensitive appeared strains characterizing by very high MIC values of some substances, eg. boric acid.

Effect of boric acid solution on cartilage metabolism.

PubMed

Benderdour, M; Hess, K; Gadet, M D; Dousset, B; Nabet, P; Belleville, F

1997-05-08

Pelvic cartilage of chick embryo was used to demonstrate that presence of boron in culture medium decreases synthesis of proteoglycans, collagen and total proteins but on the other hand increases the release of these macromolecules. However, when glucose concentration in culture medium is brought to 22mM, the synthesis decrease is no longer observed, whereas release increase persists. Proteins released into the culture medium included heat shock proteins (70 hsp) and tumor necrosis factor alpha (TNF alpha). The amount of phosphorylated proteins was enhanced in presence of boron while endoprotease activity in cartilage and in culture medium was significantly augmented. The in vitro effects of boric acid may explain its in vivo effect on wound healing.

Boric acid reversibly inhibits the second step of pre-mRNA splicing.

PubMed

Shomron, Noam; Ast, Gil

2003-09-25

Several approaches have been used to identify the factors involved in mRNA splicing. None of them, however, comprises a straightforward reversible method for inhibiting the second step of splicing using an external reagent other than a chelator. This investigation demonstrates that the addition of boric acid to an in vitro pre-mRNA splicing reaction causes a dose-dependent reversible inhibition effect on the second step of splicing. The mechanism of action does not involve chelation of several metal ions; hindrance of 3' splice-site; or binding to hSlu7. This study presents a novel method for specific reversible inhibition of the second step of pre-mRNA splicing.

Fast isotopic separation of 10 B and 11 B boric acid by capillary zone electrophoresis.

PubMed

Kamencev, Mikhail; Yakimova, Nina; Moskvin, Leonid; Kuchumova, Irina; Tkach, Kirill; Malinina, Yulia

2016-11-01

Fast isotopic separation of 10 B and 11 B boric acid by CZE was demonstrated. The BGE contained 25 mM phenylalanine and 5 mM putrescine (рН 8.95). The running conditions were +25 kV at 20°C with indirect photometric detection at 210 nm. Baseline separation was achieved in less than 9 min. RSD of migration times and corrected peak areas were less than 0.5 and 3%, respectively (n = 5). Linearity was demonstrated in the range 0.2-2 mM for 11 B and 0.2-0.5 mM for 10 B. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Resource recycling through artificial lightweight aggregates from sewage sludge and derived ash using boric acid flux to lower co-melting temperature.

PubMed

Hu, Shao-Hua; Hu, Shen-Chih; Fu, Yen-Pei

2012-02-01

This study focuses on artificial lightweight aggregates (ALWAs) formed from sewage sludge and ash at lowered co-melting temperatures using boric acid as the fluxing agent. The weight percentages of boric acid in the conditioned mixtures of sludge and ash were 13% and 22%, respectively. The ALWA derived from sewage sludge was synthesized under the following conditions: preheating at 400 degrees C 0.5 hr and a sintering temperature of 850 degrees C 1 hr. The analytical results of water adsorption, bulk density, apparent porosity, and compressive strength were 3.88%, 1.05 g/cm3, 3.93%, and 29.7 MPa, respectively. Scanning electron microscope (SEM) images of the ALWA show that the trends in water adsorption and apparent porosity were opposite to those of bulk density. This was due to the inner pores being sealed off by lower-melting-point material at the aggregates'surface. In the case of ash-derived aggregates, water adsorption, bulk density, apparent porosity, and compressive strength were 0.82%, 0.91 g/cm3, 0.82%, and 28.0 MPa, respectively. Both the sludge- and ash-derived aggregates meet the legal standards for ignition loss and soundness in Taiwan for construction or heat insulation materials.

Insights into the Mechanisms Underlying Boron Homeostasis in Plants

PubMed Central

Yoshinari, Akira; Takano, Junpei

2017-01-01

Boron is an essential element for plants but is toxic in excess. Therefore, plants must adapt to both limiting and excess boron conditions for normal growth. Boron transport in plants is primarily based on three transport mechanisms across the plasma membrane: passive diffusion of boric acid, facilitated diffusion of boric acid via channels, and export of borate anion via transporters. Under boron -limiting conditions, boric acid channels and borate exporters function in the uptake and translocation of boron to support growth of various plant species. In Arabidopsis thaliana, NIP5;1 and BOR1 are located in the plasma membrane and polarized toward soil and stele, respectively, in various root cells, for efficient transport of boron from the soil to the stele. Importantly, sufficient levels of boron induce downregulation of NIP5;1 and BOR1 through mRNA degradation and proteolysis through endocytosis, respectively. In addition, borate exporters, such as Arabidopsis BOR4 and barley Bot1, function in boron exclusion from tissues and cells under conditions of excess boron. Thus, plants actively regulate intracellular localization and abundance of transport proteins to maintain boron homeostasis. In this review, the physiological roles and regulatory mechanisms of intracellular localization and abundance of boron transport proteins are discussed. PMID:29204148

Semi-empirical equation of limiting current for cobalt electrodeposition in the presence of magnetic field and additive electrolyte

NASA Astrophysics Data System (ADS)

Sudibyo, Aziz, N.

2016-02-01

One of the available methods to solve a roughening in cobalt electrodeposition is magneto electrodeposition (MED) in the presence of additive electrolyte. Semi-empirical equation of limiting current under a magnetic field for cobalt MED in the presence of boric acid as an additive electrolyte was successfully developed. This semi empirical equation shows the effects of the electrode area (A), the concentration of the electro active species (C), the diffusion coefficient of the electro active species (D), the kinematic viscosity of the electrolyte (v), magnetic strength (B) and the number of electrons involved in the redox process (n). The presence of boric acid led to decrease in the limiting current, but the acid was found useful as a buffer to avoid the local pH rise caused by parallel hydrogen evolution reaction (HER).

Application of Taguchi optimisation of electro metal - electro winning (EMEW) for nickel metal from laterite

NASA Astrophysics Data System (ADS)

Sudibyo, Hermida, L.; Junaedi, A.; Putra, F. A.

2017-11-01

Nickel and cobalt metal able to process from low grade laterite using solvent extraction and electrowinning. One of electrowinning methods which has good performance to produce pure metal is electrometal-electrowinninge(EMEW). In this work, solventextraction was used to separate nickel and cobalt which useCyanex-Versatic Acid in toluene as an organic phase. An aqueous phase of extraction was processed using EMEW in order to deposit the nickel metal in Cathode electrode. The parameters which used in this work were batch temperature, operation time, voltage, and boric acid concentration. Those parameters were studied and optimized using the design of experiment of Taguchi. The Taguchi analysis result shows that the optimum result of EMEW was at 60°C of batch temperature, 2 Voltage, 6 hours operation and 0.5 M of boric acid.

The formation of tungsten doped Al2O3/ZnO coatings on aluminum by plasma electrolytic oxidation and their application in photocatalysis

NASA Astrophysics Data System (ADS)

Stojadinović, Stevan; Vasilić, Rastko; Radić, Nenad; Tadić, Nenad; Stefanov, Plamen; Grbić, Boško

2016-07-01

Tungsten doped Al2O3/ZnO coatings are formed by plasma electrolytic oxidation of aluminum substrate in supporting electrolyte (0.1 M boric acid + 0.05 M borax + 2 g/L ZnO) with addition of different concentrations of Na2WO4·2H2O. The morphology, crystal structure, chemical composition, and light absorption characteristics of formed surface coatings are investigated. The X-ray diffraction and X-ray photoelectron spectroscopy results indicate that formed surface coatings consist of alpha and gamma phase of Al2O3, ZnO, metallic tungsten and WO3. Obtained results showed that incorporated tungsten does not have any influence on the absorption spectra of Al2O3/ZnO coatings, which showed invariable band edge at about 385 nm. The photocatalytic activity of undoped and tungsten doped Al2O3/ZnO coatings is estimated by the photodegradation of methyl orange. The photocatalytic activity of tungsten doped Al2O3/ZnO coatings is higher thanof undoped Al2O3/ZnO coatings; the best photocatalytic activity is ascribed to coatings formed in supporting electrolyte with addition of 0.3 g/L Na2WO4·2H2O. Tungsten in Al2O3/ZnO coatings acts as a charge trap, thus reducing the recombination rate of photogenerated electron-hole pairs. The results of PL measurements are in agreement with photocatalytic activity. Declining PL intensity corresponds to increasing photocatalytic activity of the coatings, indicating slower recombination of electron-hole pairs.

Aggravation of cyclophosphamide-induced acute neurological disorders under conditions of artificial acidification of chyme in rats.

PubMed

Schaefer, T V; Rejuniuk, V L; Malakhovsky, V N; Ivnitsky, Ju Ju

2012-10-01

The effect of artificial acidification of the intestinal content on neurological manifestations of acute severe cyclophosphamide intoxication was studied in rats. The animals were gavaged with 20 ml/kg sulfuric (0.05 M), hydrochloric, boric, or lactic acids (0.1 M) 3 h before intraperitoneal injections of the cytostatic in doses of 0, 200, 600, or 1000 mg/kg. The decrease in pH (by.0) and ammonia-producing activity of the cecal chyme developed within 3 h after administration of acids. Cyclophosphamide caused hyperammonemia; glutamine/ammonia and urea/ammonia ratios in the blood decreased. These changes augmented after administration of acids (boric acid produced maximum and lactic acid minimum effects). Acid treatment resulted in greatest elevation of ammonia level in the portal venous blood and a lesser elevation in the vena cava posterior blood. Acid treatment promoted manifestation of cyclophosphamide neurotoxic effect and animal death. Hence, acidification of the chyme inhibited the formation of ammonia in it, while ammonia release from the gastrointestinal tract into the blood increased; the treatment augmented hyperammonemia and aggravated the neurological manifestations of cyclophosphamide intoxication.

Impact of the propylene glycol-water-borax coolant on material recovery operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duerksen, W.K.; Taylor, P.A.

1983-05-01

The reaction of the propylene glycol-water-borax coolant with nitric acid has now been studied in some detail. This document is intended to provide a summary of the results. Findings are summarized under nine headings. Tests have also been conducted to determine if the new coolant would have any adverse effects on the uranium recycle systems. Experiments were scientifically designed after observation of the production operations so that accurate response to the immediate production concerns could be provided. Conclusions from these studies are: formation of glycol nitrates is very improbable; the reaction of concentrated (70%) nitric acid with pure propylene glycolmore » is very violent and hazardous; dilution of the nitric acid-glycol mixture causes a drastic decrease in the rate and intensity of the reaction; the mechanism of the nitric acid propylene glycol reaction is autocatalytic in nitrous acid; no reaction is observed between coolant and 30% nitric acid unless the solution is heated; the coolant reacts fairly vigorously with 55% nitric acid after a concentration-dependent induction time; experiments showed that the dissolution of uranium chips that had been soaked in coolant proceeded at about the same rate as if the chips had not previously contacted glycol; thermodynamic calculations show that the enthalpy change (heat liberated) by the reaction of nitric acid (30%) with propylene glycol is smaller than if the same amount of nitric acid reacted with uranium. Each of these conclusions is briefly discussed. The effect of new coolant on uranium recycle operations is then briefly discussed.« less

Compared production behavior of borax and unborax premixed SiC reinforcement Al7Si-Mg-TiB alloys composites with semi-solid stir casting method

NASA Astrophysics Data System (ADS)

Haryono, M. B.; Sulardjaka, Nugroho, Sri

2016-04-01

The present study was aimed to investigate the effect of borax additive on physical and mechanical properties of Al7Si-Mg-TiB with the reinforcement of silicon carbide. In this case, the different weight percentage from the reinforcement of SiC (10, 15, and 20% wt), and the borax additive (ratio 1:4) were homogenously added into the matrix by employing the semi-solid stir casting method at the temperature of 590°C. Al7Si-Mg-TiB melted in an electric resistance furnace at 800°C for 25 minutes and the holding time of 5 minutes; SiC was stirred with borax inside the chamber and heated at the temperature of 250°C for 25 minutes. Then, it melted by lowing the temperature into 590°C. The SiC-borax mixture was added into the electric resistance furnace, and automatically stirred by the stirrer at a constant speed (500 rpm for 3 minutes) in the composite A17Si-Mg-TiB. It melted when heated at 750°C for 17minutes,then, casting was performed on the prepared mould. The characterizations of Al7Si-Mg-TiB-SiC/borax were porosity, hardness, and microstructure on the Al7Si-Mg-TiB-SiC/ borax. The porosity of AMC tended to increase along with the increaseof the wt% SiC (1.4%-3.6%); however, borax additive underwent a decrease in porosity (0.14%-1.3%). Further, hardness tended to improve along with the increase of wt% SiC. The unboraxmixture had 79,6 HRB up to 94 HRB. Whereas, the borax additive mixture had 105,8 HRB up to 121 HRB.

Reproductive toxicity in boron exposed workers in Bandirma, Turkey.

PubMed

Başaran, Nurşen; Duydu, Yalçin; Bolt, Hermann M

2012-06-01

Boric acid and sodium borates have been considered as being "toxic to reproduction and development", following results of animal studies with high doses. However unfavorable effects of boron exposure on reproduction and development have not been proved in epidemiological studies so far. The aim of the present study was to investigate the reproductive toxicity indicators in highly exposed workers employed in a boric acid production plant in Bandırma, Turkey. Two hundred and four workers participated in this study. The mean blood boron concentration of the high exposure group of workers was 223.89 ± 69.49 (152.82-454.02)ng/g. Unfavorable effects of boron exposure on the reproductive toxicity indicators were not observed. Copyright © 2012 Elsevier GmbH. All rights reserved.

Investigations of kinetics and mechanism of chloropinnoite in boric acid aqueous solution at 303 K by Raman spectroscopy.

PubMed

Xiaoping, Li; Shiyang, Gao; Shuping, Xia

2004-10-01

Raman spectroscopy of dissolution and transformation of chloropinnoite in 4.5% (wt.%) boric acid aqueous solution at 303 K has been recorded. The Raman spectra of kinetics process have been obtained. The phase transformation product is 2MgO.3B2O3.15H2O (kurnakovite). The main polyborate anions and their interaction in aqueous solution have been proposed according to the Raman spectrum. Some assignments were tentatively given and the relations between the existing forms of polyborate anions and the crystallizing solid phases have been gained. A mechanism of dissolution and crystallization reactions and the formation condition of kurnakovite in Qinghai-Tibet plateau were proposed and discussed.

[Raman spectroscopic analysis of dissolution and phase transformation of chloropinnoite in the boric acid aqueous solution].

PubMed

Li, Xiao-Ping; Gao, Shi-Yang; Liu, Zhi-Hong; Hu, Man-Cheng; Xia, Shu-Ping

2005-01-01

Raman spectroscopy of dissolution and transformation of chloropinnoite in 4.5% (w.t.%) boric acid aqueous solution at 30 degrees C has been recorded. The Raman spectra of kinetics process have been obtained. The phase transformation product is kurnakovite (2MgO x 3B2O3 x 15H2O). The main polyborate anions and their interaction in aqueous solution have been proposed according to the Raman spectrum. Some assignments were tentatively given and the relations between the existing forms of polyborate anions and the crystallizing solid phases have been gained. A mechanisms of dissolution and crystallization reactions and the formation condition of kurnakovite in Qinghai-Tibet plateau were proposed and discussed.

Effect of single flame retardant aluminum tri-hydroxide and boric acid against inflammability and biodegradability of recycled PP/KF composites

NASA Astrophysics Data System (ADS)

Suharty, Neng Sri; Dihardjo, Kuncoro; Handayani, Desi Suci; Firdaus, Maulidan

2016-03-01

Composites rPP/DVB/AA/KF had been reactively synthesized in melt using starting material: recycled polypropylene (rPP), kenaf fiber (KF), multifunctional compound acrylic acid (AA), compatibilizer divinyl benzene (DVB). To improve the inflammability of composites, single flame retardant aluminum tri-hydroxide (ATH) and boric acid (BA) as an additive was added. The inflammability of the composites was tested according to ASTM D635. By using 20% ATH and 5% BA additive in the composites it is effectively inhibiting its time to ignition (TTI). Its burning rate (BR) can be reduced and its heat realease (%HR) decreases. The biodegradability of composites was quantified by its losing weight (LW) of composites after buried for 4 months in the media with rich cellulolytic bacteria. The result shows that the LW of composites in the presence 20% ATH and 5% BA is 6.3%.

Swelling and tensile properties of starch glycerol system with various crosslinking agents

NASA Astrophysics Data System (ADS)

Mohamed, R.; Mohd, N.; Nurazzi, N.; Siti Aisyah, M. I.; Fauzi, F. Mohd

2017-07-01

Brittle properties of starch had been overcome by the modification process. In this work, sago starch is being modified with variable amount of plasticiser, namely glycerol at 20 and 40% and crosslinking agent had been added to the system. The film of the modification and characterizations of the starch glycerol system with various crosslinking systems were produced by casting method. The film properties of the starch glycerol system were then characterized by tensile strength (mechanical properties) and swelling (physical properties). The modification of the starch glycerol had improved that system by increasing the tensile strength, modulus however lowering its elongation. The increasing in percentage of the water absorption and also swelling are due to the intrinsic hydroxyl groups presence from the starch and glycerol itself that can attract more water to the system. Upon crosslinking, films casted with chemicals namely, glyoxal, malonic acid, borax, PEG were characterised. It was found that, all the film of sago starch crosslinked and undergoing easy film formation. From this modification, borax and malonic acid crosslinking agent had been determined as the best crosslinking agent to the starch glycerol system.

High performances of dual network PVA hydrogel modified by PVP using borax as the structure-forming accelerator

PubMed Central

Huang, Min; Hou, Yi; Li, Yubao; Wang, Danqing; Zhang, Li

2017-01-01

Abstract A dual network hydrogel made up of polyvinylalcohol (PVA) crosslinked by borax and polyvinylpyrrolidone (PVP) was prepared by means of freezing-thawing circles. Here PVP was incorporated by linking with PVA to form a network structure, while the introduction of borax played the role of crosslinking PVA chains to accelerate the formation of a dual network structure in PVA/PVP composite hydrogel, thus endowing the hydrogel with high mechanical properties. The effects of both PVP and borax on the hydrogels were evaluated by comparing the two systems of PVA/PVP/borax and PVA/borax hydrogels. In the former system, adding 4.0% PVP not only increased the water content and the storage modulus but also enhanced the mechanical strength of the final hydrogel. But an overdose of PVP just as more than 4.0% tended to undermine the structure of hydrogels, and thus deteriorated hydrogels’ properties because of the weakened secondary interaction between PVP and PVA. Likewise, increasing borax could promote the gel crosslinking degree, thus making gels show a decrease in water content and swelling ratio, meanwhile shrinking the pores inside the hydrogels and finally enhancing the mechanical strength of hydrogels prominently. The developed hydrogel with high performances holds great potential for applications in biomedical and industrial fields. PMID:29491822

Intracrystalline site preference of hydrogen isotopes in borax

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pradhananga, T.M.; Matsuo, S.

1985-01-03

The total hydrogen involved in borax synthesized at 25/sup 0/C in aqueous solution is enriched in deuterium by 5.3% compared with the mother liquor. There is no change in the value of the D/H fractionation factor between the hydrogen in borax and those in the mother liquor with changes in the degree of supersaturation. The fractionation factor changes slightly with a change in the crystallization temperature of borax in the range from 5 to 25/sup 0/C. The D/H ratio in the different sites of borax was estimated by a fractional dehydration technique. The results show that hydrogen atoms of themore » polyanionic group (B/sub 4/O/sub 5/(OH)/sub 4/) are much more enriched in deuterium than those of the cationic group (Na/sub 2/ x 8H/sub 2/O). The delta D values, referred to the mother liquor from which the borax was crystallized, for the cationic group (site A) and the polyanionic group (site B) are -35 +/- 3 and 167 +/- 13%, respectively based on the fractional dehydration results obtained at -21/sup 0/C. At -21/sup 0/C, isotopic exchange between different sites during dehydration is assumed not to occur. The mechanism for dehydration of borax is discussed. 48 references, 8 figures, 3 tables.« less

The preservation of urine samples for determination of renal stone risk factors

NASA Technical Reports Server (NTRS)

Nicar, M. J.; Hsu, M. C.; Johnson, T.; Pak, C. Y.

1987-01-01

A preservation technique for urine specimens before determination of stone risk factors was evaluated. The purpose of these experiments was to prove the effectiveness of the preservatives used to prevent changes in the concentrations of those constituents measured. Measured concentrations in fresh specimens were compared with those in the same specimens after storage with the preservatives. Refrigeration at 4 degrees C up to five days was appropriate in a laboratory setting, as no significant changes in urinary concentrations occurred. Refrigeration, however, did not offer a convenient method for shipping. Chemical preservation was found to be an effective alternative to refrigeration. Thymol prevented changes in concentration of pH, citrate, uric acid, sulfate, sodium, potassium, and cyclic AMP, while a mixture of hydrochloric (HCl) acid and boric acid prevented changes in calcium, magnesium, phosphorus, oxalate, ammonium, and creatinine. Thus, the addition of thymol or HCl/boric acid to urine specimens will prevent significant changes in the concentrations of stone risk factors.

Results of turbojet engine operation tests using a 50-50 mixture of JP-4 and tributyl borate as the fuel

NASA Technical Reports Server (NTRS)

Schafer, Louis J , Jr; Stepka, Francis S

1957-01-01

An experimental investigation was conducted on a centrifugal-type turbojet engine using a 50-50 mixture of tributyl borate and JP-4 as the fuel to determine the magnitude and the location of the boric oxide deposits in the engine as well as the effect of these deposits on the engine performance. Large deposits of boric acid formed in the combustor walls and on the turbine rotor and stator blades. The deposits had no effect on the engine thrust.

A Study of Cross-linked Regions of Poly(Vinyl Alcohol) Gels by Small-Angle Neutron Scattering

NASA Astrophysics Data System (ADS)

Lawrence, Mathias B.; Desa, J. A. E.; Aswal, V. K.

2011-07-01

A poly(vinyl alcohol)-borax cross-linked hydrogel has been studied by Small Angle Neutron Scattering as a function of borax concentration in the wave-vector transfer (Q) range of 0.017 Å-1 to 0.36 Å-1. It is found that as the concentration of borax increases, so does the intensity of scattering in this range. Beyond a borax concentration of 2 mg/ml, the increase in cross-linked PVA chains leads to cross-linked units larger than 150 Å as evidenced by a reduction in intensity in the lower Q region.

SURFACE HARDENING OF TITANIUM BY TREATMENT IN MOLTEN BORAX

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minkevich, A.N.; Shul'ga, Yu.N.

1957-01-01

The surface hardening of titanium and titanium alloys by treatment in molten borax was investigated. Commercial titanium, a titanium-tungsten alloy, and an aluminum-chromium-titanium alloy were used for the experiments. To prevent oxidation of the titanium and to protect the surface, electro-chemical protection was applied, the current density being 0.1 amp/cm/sup 2/ and the the specimens were coated with a thin layer of borax. The results showed that treatment in molten borax is an effective method of increasing surface hardness. However, the strength, mmalleabiltiy, and toughness of the hardness increase is discussed. (J.S.R.)

Theory of Ion and Water Transport in Reverse-Osmosis Membranes

NASA Astrophysics Data System (ADS)

Oren, Y. S.; Biesheuvel, P. M.

2018-02-01

We present a theory for ion and water transport through reverse-osmosis (RO) membranes based on a Maxwell-Stefan framework combined with hydrodynamic theory for the reduced motion of particles in thin pores. We take into account all driving forces and frictions both on the fluid (water) and on the ions including ion-fluid friction and ion-wall friction. By including the acid-base characteristic of the carbonic acid system, the boric acid system, H3O+/OH- , and the membrane charge, we locally determine p H , the effective charge of the membrane, and the dissociation degree of carbonic acid and boric acid. We present calculation results for an experiment with fixed feed concentration, where effluent composition is a self-consistent function of fluxes through the membrane. A comparison with experimental results from literature for fluid flow vs pressure, and for salt and boron rejection, shows that our theory agrees very well with the available data. Our model is based on realistic assumptions for the effective size of the ions and makes use of a typical pore size of a commercial RO membrane.

Impact of boron rich layer on performance degradation in boric acid diffused emitters for n-type crystalline Si solar cells

NASA Astrophysics Data System (ADS)

Singha, Bandana; Singh Solanki, Chetan

2018-01-01

Boron rich layer (BRL) formed beneath the borosilicate glass layer during p-type emitter formation is an undesirable phenomenon. It influences different cell parameters and can degrade the device performance. In this work, the device degradation study is done for different BRL thicknesses produced with different concentrations of the boric acid dopant source. The bulk carrier lifetime reduces to more than 75% and emitter saturation current density becomes more than 10-12 mA cm-2 for 60 nm of BRL thickness. The observed J sc and V oc values become zero for BRL thicknesses higher than 40 nm as seen in this work and the device properties could not be enhanced. So, higher thicknesses of BRL should be avoided.

The Aquaporin Splice Variant NbXIP1;1α Is Permeable to Boric Acid and Is Phosphorylated in the N-terminal Domain

PubMed Central

Ampah-Korsah, Henry; Anderberg, Hanna I.; Engfors, Angelica; Kirscht, Andreas; Norden, Kristina; Kjellstrom, Sven; Kjellbom, Per; Johanson, Urban

2016-01-01

Aquaporins (AQPs) are membrane channel proteins that transport water and uncharged solutes across different membranes in organisms in all kingdoms of life. In plants, the AQPs can be divided into seven different subfamilies and five of these are present in higher plants. The most recently characterized of these subfamilies is the XIP subfamily, which is found in most dicots but not in monocots. In this article, we present data on two different splice variants (α and β) of NbXIP1;1 from Nicotiana benthamiana. We describe the heterologous expression of NbXIP1;1α and β in the yeast Pichia pastoris, the subcellular localization of the protein in this system and the purification of the NbXIP1;1α protein. Furthermore, we investigated the functionality and the substrate specificity of the protein by stopped-flow spectrometry in P. pastoris spheroplasts and with the protein reconstituted in proteoliposomes. The phosphorylation status of the protein and localization of the phosphorylated amino acids were verified by mass spectrometry. Our results show that NbXIP1;1α is located in the plasma membrane when expressed in P. pastoris, that it is not permeable to water but to boric acid and that the protein is phosphorylated at several amino acids in the N-terminal cytoplasmic domain of the protein. A growth assay showed that the yeast cells expressing the N-terminally His-tagged NbXIP1;1α were more sensitive to boric acid as compared to the cells expressing the C-terminally His-tagged isoform. This might suggest that the N-terminal His-tag functionally mimics the phosphorylation of the N-terminal domain and that the N-terminal domain is involved in gating of the channel. PMID:27379142

Performance Characteristics of Borate Fatty Acid Formulations as Mold Inhibitors

Treesearch

Robert D. Coleman; Vina Yang; Carol A. Clausen

2013-01-01

The combination of boric acid (BA) or disodium octaborate tetrahydrate (DOT) and a fatty acid (FA) such as heptanoic, octanoic, and nonanoic acids (C7–C9) is an effective treatment solution for protecting wood structures against mold. BA or DOT alone have substantial potency against insects and decay fungi, but have negligible or no mold inhibitor activity. However,...

PHOTOGRAPHIC FILM DEVELOPER

DOEpatents

Berry, F.G.

1958-06-24

S>An improved photographic developer is presented having very high energy development fine grain characteristics and a long shelf life. These characteristics are obtained by the use of aminoacetic acid in the developer, the other constituents of which are: sodium sulfite, hydroquinone, sodiunn borate, boric acid and potassium bromide, 1-phenyl-3-pyrazolidone.

Hydrologic data and description of a hydrologic monitoring plan for the Borax Lake area, Oregon

USGS Publications Warehouse

Schneider, Tiffany Rae; McFarland, William D.

1995-01-01

Information from field visits was used to develop a monitoring plan. The plan would include monitoring Borax Lake by measuring discharge, stage, evaporation, temperature, and specific conductance; water-quality sampling and analysis; and monitoring shallow ground-water levels near Borax Lake using shallow piezometers. Minimally, one hot spring in North Borax Lake Spring Group 1 would be monitored for temperature and specific conductance and sampled for water-quality analysis. In addition, two flowing wells would be monitored for water levels, temperature, specific conductance, and discharge and sampled for water-quality analysis. The construction characteristics of these wells must be verified before long-term data collection begins. In the future, it may be helpful to monitor shallow and (or) deep observation wells drilled into the thermal aquifer to understand the possible effects of geothermal development on Borax Lake and nearby springs.

Synthesis of boron suboxide from boron and boric acid under mild pressure and temperature conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiao, Xiaopeng; Jin, Hua; Ding, Zhanhui

2011-05-15

Graphical abstract: Well-crystallized and icosahedral B{sub 6}O crystals were prepared by reacting boron and boric acid at milder reaction conditions (1 GPa and 1300 {sup o}C for 2 h) as compared to previous work.. Research highlights: {yields} Well-crystallized icosahedral B{sub 6}O was synthesized by reacting boric acid and boron. {yields} The synthesis conditions (1 GPa and 1300 {sup o}C for 2 h) are milder in comparison with previous work. {yields} The more practical synthesis method may make B{sub 6}O as a potential substitute for diamond in industry. -- Abstract: Boron suboxide (B{sub 6}O) was synthesized by reacting boron and boricmore » acid (H{sub 3}BO{sub 3}) at pressures between 1 and 10 GPa, and at temperatures between 1300 and 1400 {sup o}C. The B{sub 6}O samples prepared were icosahedral with diameters ranging from 20 to 300 nm. Well-crystallized and icosahedral crystals with an average size of {approx}100 nm can be obtained at milder reaction conditions (1 GPa and 1300 {sup o}C for 2 h) as compared to previous work. The bulk B{sub 6}O sample was stable in air at 600 {sup o}C and then slowly oxidized up to 1000 {sup o}C. The relatively mild synthetic conditions developed in this study provide a more practical synthesis of B{sub 6}O, which may potentially be used as a substitute for diamond in industry as a new superhard material.« less

Borax Stump Treatment for Control of Annosus Root Disease in the Eastside Pine Type Forests of Northeastern California

Treesearch

John T. Kliejunas

1989-01-01

A historical perspective and description of recent studies on the use of borax to treat pine stumps against infection by Heterobasidion annosum in eastside pine stands of northeastern California are presented. The studies indicate that boraxing of pines in eastside pine stands is an effective means of preventing annosus infection. Data and...

Development work for a borax internal core-catcher for a gas-cooled fast reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donne, M.D.; Dorner, S.; Schumacher, G.

1978-07-01

Preliminary thermal calculations show that a corecatcher, which is able to cope with the complete meltdown of the core and blankets of a 1000-MW(electric) gas-cooled fast reactor, appears to be feasible. This core-catcher is based on borax (Na/sub 2/B/sub 4/O/sub 7/) dissolving the oxide fuel and the fission products occurring in oxide form. The borax is contained in steel boxes forming a 2.2-m-thick slab on the base of the reactor cavity inside the prestressed concrete reactor vessel (PCRV), just underneath the reactor core. After a complete meltdown accident, the fission products, in oxide form, are dispersed in the pool formedmore » by the liquid borax. The metallic fission products are contained in the steel lying below the borax pool and in contact with the water-cooled PCRV liner. The volumetric power density of the molten core is conveniently reduced as it is dissolved in the borax, and the resulting heat fluxes at the borders of the pool can be safely carried away through the PCRV liner and its water cooling system.« less

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.

2013-06-26

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01 M) boric acid streammore » into the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B203 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 - SB8 flowsheet to additions of B203 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 - SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B203 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B203 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT.« less

A step into the RNA world: Conditional analysis of hydrogel formation of adenosine 5'-monophosphate induced by cyanuric acid.

PubMed

Yokosawa, Takumi; Enomoto, Ryota; Uchino, Sho; Hirasawa, Ito; Umehara, Takuya; Tamura, Koji

2017-12-01

Nucleotide polymerization occurs by the nucleophilic attack of 3'-oxygen of the 3'-terminal nucleotide on the α-phosphorus of the incoming nucleotide 5'-triphosphate. The π-stacking of mononucleotides is an important factor for prebiotic RNA polymerization in terms of attaining the proximity of two reacting moieties. Adenosine and adenosine 5'-monophosphate (AMP) are known to form hydrogel in the presence of cyanuric acid at neutral pH. However, we observed that other canonical ribonucleotides did not gel under the same condition. The π-stacking-induced hydrogel formation of AMP was destroyed at pH 2.0, suggesting that the protonation of N at position 1 of adenine abolished hydrogen bonding with the NH of cyanuric acid and resulted in the deformation of the hexad of adenine and cyanuric acid. A liquid-like gel was formed in the case of adenosine with cyanuric acid and boric acid, whereas AMP caused the formation of a solid gel, implying that the negative charge inherent to AMP prevented the formation of esters of boric acid with the cis-diols of ribose. Cyanuric acid-driven oligomerizations of AMP might have been the first crucial event in the foundation of the RNA world. Copyright © 2017 Elsevier B.V. All rights reserved.

A promising red-emitting phosphor for white-light-emitting diodes prepared by a modified solid-state reaction

NASA Astrophysics Data System (ADS)

Ren, Fuqiang; Chen, Donghua

2010-02-01

Using urea, boric acid and polyethylene glycol (PEG) as auxiliary reagents, the novel red-emitting phosphors Ca 19Zn 2 (PO 4) 14:Eu 3+ have been successfully synthesized by a modified solid-state reaction. Thermogravimetric (TG) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence (PL) spectra were used to characterize the resulting phosphors. The dependence of the photoluminescence properties of Ca 19Zn 2 (PO 4) 14:Eu 3+ phosphors upon urea, boric acid and PEG concentration and the quadric-sintered temperature were investigated. Luminescent measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a red light with a peak wavelength of 616 nm. The material has potential application as a fluorescent material for ultraviolet light-emitting diodes (UV-LEDs).

Method of synthesizing enriched decaborane for use in generating boron neutron capture therapy pharmaceuticals

DOEpatents

Cowan, Robert L.; Ginosar, Daniel M.; Dunks, Gary B.

2000-01-01

A method is described for synthesizing decaborane wherein at least about 90% of the boron atoms in the decaborane are the .sup.10 B isotope, comprising the steps of: (a) reacting boric acid with a C.sub.1 to C.sub.10 alkanol to form a .sup.10 B-alkyl borate wherein at least about 90% of the boron atoms in the boric acid are the .sup.10 B isotope; (b) reducing the .sup.10 B-alkyl borate to form an alkali metal .sup.10 B-borohydride; (c) converting the alkali metal .sup.10 B-borohydride to a .sup.10 B-tetradecahydroundecaborate ion; and (d) converting the .sup.10 B-tetradecahydroundecaborate ion to .sup.10 B-decaborane. Methods of preparing tetradecahydroundecaborate ions and decaborane from alkali metal borohydrides are also described.

Synthesis and Photoluminescence Properties of Li2SrSiO4 Activated with Dy3+ and Sm3+

NASA Astrophysics Data System (ADS)

Erdoğmuş, E.

2015-01-01

Li2SrSiO4:M (M: Dy3+ and Sm3+) phosphors were synthesized by the conventional solid state reaction. The synthesized materials were characterized by powder XRD. The emission and excitation spectra of these phosphors were measured at room temperature with a spectrofluorometer. The first phosphor, Li2SrSiO4:Dy3+, emits at 479, 573, and 666 nm upon 351 nm excitation. The second phosphor, Li2SrSiO4:Sm3+, emits at 561-571, 594, 647-655, and 703-713 nm upon 399 nm excitation. Also, the dependence of the photoluminescence properties of both phosphors on boric acid concentration was investigated. The results showed that boric acid was effective in improving the photoluminescence intensity of both phosphors.

Permeability and channel-mediated transport of boric acid across membrane vesicles isolated from squash roots.

PubMed

Dordas, C; Chrispeels, M J; Brown, P H

2000-11-01

Boron is an essential micronutrient for plant growth and the boron content of plants differs greatly, but the mechanism(s) of its uptake into cells is not known. Boron is present in the soil solution as boric acid and it is in this form that it enters the roots. We determined the boron permeability coefficient of purified plasma membrane vesicles obtained from squash (Cucurbita pepo) roots and found it to be 3 x 10(-7) +/-1.4 x 10(-8) cm s(-1), six times higher than the permeability of microsomal vesicles. Boric acid permeation of the plasma membrane vesicles was partially inhibited (30%-39%) by mercuric chloride and phloretin, a non-specific channel blocker. The inhibition by mercuric chloride was readily reversible by 2-mercaptoethanol. The energy of activation for boron transport into the plasma membrane vesicles was 10.2 kcal mol(-1). Together these data indicate that boron enters plant cells in part by passive diffusion through the lipid bilayer of the plasma membrane and in part through proteinaceous channels. Expression of the major intrinsic protein (MIP) PIP1 in Xenopus laevis oocytes resulted in a 30% increase in the boron permeability of the oocytes. Other MIPs tested (PIP3, MLM1, and GlpF) did not have this effect. We postulate that certain MIPs, like those that have recently been shown to transport small neutral solutes, may also be the channels through which boron enters plant cells.

Permeability and Channel-Mediated Transport of Boric Acid across Membrane Vesicles Isolated from Squash Roots1

PubMed Central

Dordas, Christos; Chrispeels, Maarten J.; Brown, Patrick H.

2000-01-01

Boron is an essential micronutrient for plant growth and the boron content of plants differs greatly, but the mechanism(s) of its uptake into cells is not known. Boron is present in the soil solution as boric acid and it is in this form that it enters the roots. We determined the boron permeability coefficient of purified plasma membrane vesicles obtained from squash (Cucurbita pepo) roots and found it to be 3 × 10−7 ±1.4 × 10−8 cm s−1, six times higher than the permeability of microsomal vesicles. Boric acid permeation of the plasma membrane vesicles was partially inhibited (30%–39%) by mercuric chloride and phloretin, a non-specific channel blocker. The inhibition by mercuric chloride was readily reversible by 2-mercaptoethanol. The energy of activation for boron transport into the plasma membrane vesicles was 10.2 kcal mol−1. Together these data indicate that boron enters plant cells in part by passive diffusion through the lipid bilayer of the plasma membrane and in part through proteinaceous channels. Expression of the major intrinsic protein (MIP) PIP1 in Xenopus laevis oocytes resulted in a 30% increase in the boron permeability of the oocytes. Other MIPs tested (PIP3, MLM1, and GlpF) did not have this effect. We postulate that certain MIPs, like those that have recently been shown to transport small neutral solutes, may also be the channels through which boron enters plant cells. PMID:11080310

A commercial application of fire retardants to dry-formed hardboards

Treesearch

Gary C. Meyers; Carlton A. Holmes

1977-01-01

Based on laboratory performance with a number of fire-retardant chemicals, disodium octaborate tetrahydrate-boric acid and dicyandiamide-phosphoric acid-formaldehyde were selected for treating fiber and making 4 foot by 8-foot dry-formed hardboards on a commercial production line. The boards were evaluated for performance under exposure to fire, strength, dimensional...

The effect of boron on plasma membrane electron transport and associated proton secretion by cultured carrot cells.

PubMed

Barr, R; Böttger, M; Crane, F L

1993-09-01

Plasma membrane electron transport reactions and associated proton secretion were studied in boron-deficient carrot cells. It was found that the hormone-sensitive plasma membrane NADH oxidase was inhibited by boron deficiency and that under such conditions activity could be restored by exogenous boric acid with or without 2,4-dichlorophenoxy acetic acid. Gramicidin, a channel-forming protonophore, further stimulated NADH oxidase by carrot cells. Proton secretion, associated with plasma membrane H(+)-ATPase, was also affected by boron deficiency, but not as severely as ferricyanide-generated proton secretion, reflecting plasma membrane electron transport. The addition of 1 mM boric acid and 1 microM 2,4-dichlorophenoxy acetic acid to carrot cells fully restored the H+ secretion in presence of ferricyanide. The effect of boron deficiency in cultured carrot cells can, therefore, be directly associated with cell growth through its effect on the plasma membrane NADH oxidase and H+ secretion. Ferricyanide provides a probe which activates transmembrane electron transport that is only coupled to proton release when boron is present.

Decontamination and decommissioning of the BORAX-V leach pond. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, D.L.

1985-01-01

This report describes the decontamination and decommissioning (D and D) of the BORAX-V leach pond located at the Idaho National Engineering Laboratory (INEL). The leach pond became radioactively contaminated from the periodic discharge of low-level liquid waste during operation of the Boiling Water Reactor Experiments (BORAX) from 1954 to 1964. This report describes work performed to accomplish the D and D objectives of stabilizing the leach pond and preventing the spread of contamination. D and D of the BORAX-V leach pond consisted to backfilling the pond with clean soil, grading and seeding the area, and erecting a permanent marker tomore » identify very low-level subsurface contamination.« less

Borax as flux on sintering of iron Ancor Steel 1000® under glow discharge

NASA Astrophysics Data System (ADS)

Ariza Suarez, H. G.; Sarmiento Santos, A.; Ortiz Otálora, C. A.

2016-02-01

This work studies the flux effect of borax (di sodium tetraborate decahydrate) on sintering of iron Ancor Steel 1000® in abnormal glow discharge. The incidence of the percentage by weight of borax and the sintering temperature in the process were observed. Samples of powder metallurgical iron were prepared with proportions of 0.50%, 2.0%, 4.0% and 6.0% by weight of borax using the procedures of powder metallurgy. The samples were sintered at 800 and 1100°C for 30min, by glow discharge at low pressure in a reducing atmosphere composed of 20% H2+80% Ar. The samples in compact green-state were analyzed by TGA-DSC to determine the fusion process and mass loss during sintering. The analysis of microhardness and density, shows that at a sintering temperature of 800°C the sample density decreases and the sample microhardness increases with respect to sintered samples without borax. Sintered samples were analysed by DRX showing the absence of precipitates.

Characterization of uranium surfaces machined with aqueous propylene glycol-borax or perchloroethylene-mineral oil coolants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cristy, S.S.; Bennett, R.K. Jr.; Dillon, J.J.

1986-12-31

The use of perchloroethylene (perc) as an ingredient in coolants for machining enriched uranium at the Oak Ridge Y-12 Plant has been discontinued because of environmental concerns. A new coolant was substituted in December 1985, which consists of an aqueous solution of propylene glycol with borax (sodium tetraborate) added as a nuclear poison and with a nitrite added as a corrosion inhibitor. Uranium surfaces machined using the two coolants were compared with respects to residual contamination, corrosion or corrosion potential, and with the aqueous propylene glycol-borax coolant was found to be better than that of enriched uranium machined with themore » perc-mineral oil coolant. The boron residues on the final-finished parts machined with the borax-containing coolant were not sufficient to cause problems in further processing. All evidence indicated that the enriched uranium surfaces machined with the borax-containing coolant will be as satisfactory as those machined with the perc coolant.« less

Permanence and diffusion of borax-copper hydroxide remedial preservative applied to unseasoned pine posts : 10 year update

Treesearch

Douglas Crawford; Stan Lebow; Mike West; Bill Abbott

2005-01-01

In 1993, unseasoned pine posts were treated with groundline remedial treatment containing 3.1% copper hydroxide and 40% sodium tetraborate decahydrate (borax). The soundness of the posts was periodically evaluated using a push test. After 3.5, 6.5, and 10 years, sections were taken from two posts to determine retention of borax and copper hydroxide below ground to 36...

Response to Thermal Exposure of Ball-Milled Aluminum-Borax Powder Blends

NASA Astrophysics Data System (ADS)

Birol, Yucel

2013-04-01

Aluminum-borax powder mixtures were ball milled and heated above 873 K (600 °C) to produce Al-B master alloys. Ball-milled powder blends reveal interpenetrating layers of deformed aluminum and borax grains that are increasingly refined with increasing milling time. Thermal exposure of the ball-milled powder blends facilitates a series of thermite reactions between these layers. Borax, dehydrated during heating, is reduced by Al, and B thus generated reacts with excess Al to produce AlB2 particles dispersed across the aluminum grains starting at 873 K (600 °C). AlB2 particles start to form along the interface of the aluminum and borax layers. Once nucleated, these particles grow readily to become hexagonal-shaped crystals that traverse the aluminum grains with increasing temperatures as evidenced by the increase in the size as well as in the number of the AlB2 particles. Ball milling for 1 hour suffices to achieve a thermite reaction between borax and aluminum. Ball milling further does not impact the response of the powder blend to thermal exposure. The nucleation-reaction sites are multiplied, however, with increasing milling time and thus insure a higher number of smaller AlB2 particles. The size of the AlB2 platelets may be adjusted with the ball milling time.

Plasma impregnation of wood with fire retardants

NASA Astrophysics Data System (ADS)

Pabeliña, Karel G.; Lumban, Carmencita O.; Ramos, Henry J.

2012-02-01

The efficacy of chemical and plasma treatments with phosphate and boric compounds, and nitrogen as flame retardants on wood are compared in this study. The chemical treatment involved the conventional method of spraying the solution over the wood surface at atmospheric condition and chemical vapor deposition in a vacuum chamber. The plasma treatment utilized a dielectric barrier discharge ionizing and decomposing the flame retardants into innocuous simple compounds. Wood samples are immersed in either phosphoric acid, boric acid, hydrogen or nitrogen plasmas or a plasma admixture of two or three compounds at various concentrations and impregnated by the ionized chemical reactants. Chemical changes on the wood samples were analyzed by Fourier transform infrared spectroscopy (FTIR) while the thermal changes through thermo gravimetric analysis (TGA). Plasma-treated samples exhibit superior thermal stability and fire retardant properties in terms of highest onset temperature, temperature of maximum pyrolysis, highest residual char percentage and comparably low total percentage weight loss.

FFT-impedance spectroscopy analysis of the growth of magnetic metal nanowires in ultra-high aspect ratio InP membranes

NASA Astrophysics Data System (ADS)

Gerngross, M.-D.; Carstensen, J.; Föll, H.; Adelung, R.

2016-01-01

This paper reports on the characterization of the electrochemical growth process of magnetic nanowires in ultra-high-aspect ratio InP membranes via in situ fast Fourier transform impedance spectroscopy in a typical frequency range from 75 Hz to 18.5 kHz. The measured impedance data from the Ni, Co, and FeCo can be very well fitted using the same electric equivalent circuit consisting of a series resistance in serial connection to an RC-element and a Maxwell element. The impedance data clearly indicate the similarities in the growth behavior of Ni, Co and FeCo nanowires in ultra-high aspect ratio InP membranes—the beneficial impact of boric acid on the metal deposition in ultra-high aspect ratio membranes and the diffusion limitation of boric acid, as well as differences such as passivation or side reactions.

Autoradiographic and histopathological studies of boric acid-mediated BNCT in hepatic VX2 tumor-bearing rabbits: Specific boron retention and damage in tumor and tumor vessels.

PubMed

Yang, C H; Lin, Y T; Hung, Y H; Liao, J W; Peir, J J; Liu, H M; Lin, Y L; Liu, Y M; Chen, Y W; Chuang, K S; Chou, F I

2015-12-01

Hepatoma is a malignant tumor that responds poorly to conventional therapies. Boron neutron capture therapy (BNCT) may provide a better way for hepatoma therapy. In this research, (10)B-enriched boric acid (BA, 99% (10)B) was used as the boron drug. A multifocal hepatic VX2 tumor-bearing rabbit model was used to study the mechanisms of BA-mediated BNCT. Autoradiography demonstrated that BA was selectively targeted to tumors and tumor vessels. Histopathological examination revealed the radiation damage to tumor-bearing liver was concentrated in the tumor regions during BNCT treatment. The selective killing of tumor cells and the destruction of the blood vessels in tumor masses may be responsible for the success of BA-mediated BNCT for liver tumors. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of Boron diffused emitters from BN, BSoD and H3BO3 dopants

NASA Astrophysics Data System (ADS)

Singha, Bandana; Singh Solanki, Chetan

2016-12-01

In this work, we are comparing different limited boron dopant sources for the emitter formation in n-type c-Si solar cells. High purity boric acid solution, commercially available boron spin on dopant and boron nitride solid source are used for comparison of emitter doping profiles for the same time and temperature conditions of diffusion. The characterizations done for the similar sheet resistance values for all the dopant sources show different surface morphologies and different device parameters. The measured emitter saturation current densities (Joe) are more than 20 fA cm-2 for all the dopant sources. The bulk carrier lifetimes measured for different diffusion conditions and different solar cell parameters for the similar sheet resistance values show the best result for boric acid diffusion and the least for BN solid source. So, different dopant sources result in different emitter and cell performances.

Desulphurization of coal using borax

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yaman, S.; Kuecuekbayrak, S.

1996-12-31

In this study, a high sulphur Turkish lignite was mixed with various amounts of solid borax [Na{sub 2}B{sub 4}O{sub 7}10H{sub 2}O] and then these mixtures were subjected to various oxydesulphurization processes. Effects of amount of borax, temperature and partial pressure of oxygen on sulphur removal and coal recovery were investigated in the ranges of 0.625--15.000 g for 5 g lignite, 423--498 K, 0.0--1.5 MPa, respectively.

Reproductive toxicity parameters and biological monitoring in occupationally and environmentally boron-exposed persons in Bandirma, Turkey.

PubMed

Duydu, Yalçın; Başaran, Nurşen; Üstündağ, Aylin; Aydin, Sevtap; Ündeğer, Ülkü; Ataman, Osman Yavuz; Aydos, Kaan; Düker, Yalçın; Ickstadt, Katja; Waltrup, Britta Schulze; Golka, Klaus; Bolt, Hermann M

2011-06-01

Boric acid and sodium borates have been considered as being "toxic to reproduction and development", following results of animal studies with high doses. Experimentally, a NOAEL (no observed adverse effect level) of 17.5 mg B/kg-bw/day has been identified for the (male) reproductive effects of boron in a multigeneration study of rats, and a NOAEL for the developmental effects in rats was identified at 9.6 mg B/kg-bw/day. These values are being taken as the basis of current EU safety assessments. The present study was conducted to investigate the reproductive effects of boron exposure in workers employed in boric acid production plant in Bandirma, Turkey. In order to characterize the external and internal boron exposures, boron was determined in biological samples (blood, urine, semen), in workplace air, in food, and in water sources. Unfavorable effects of boron exposure on the reproductive toxicity indicators (concentration, motility, morphology of the sperm cells and blood levels of follicle-stimulating hormone (FSH), luteinizing hormone (LH), and total testosterone) were not observed. The mean calculated daily boron exposure (DBE) of the highly exposed group was 14.45 ± 6.57 (3.32-35.62) mg/day. These human exposures represent worst-case exposure conditions to boric acid/borates in Turkey. These exposure levels are considerably lower than exposures, which have previously led to reproductive effects in experimental animals. In conclusion, this means that dose levels of boron associated with developmental and reproductive toxic effects in animals are by far not reachable for humans under conditions of normal handling and use.

Ecotoxicity of boric acid in standard laboratory tests with plants and soil organisms.

PubMed

Princz, Juliska; Becker, Leonie; Scheffczyk, Adam; Stephenson, Gladys; Scroggins, Rick; Moser, Thomas; Römbke, Jörg

2017-05-01

To verify the continuous sensitivity of ecotoxicological tests (mainly the test organisms), reference substances with known toxicity are regularly tested. Ideally, this substance(s) would lack specificity in its mode action, be bioavailable and readily attainable with cost-effective means of chemical characterization. Boric acid has satisfied these criteria, but has most recently been characterized as a substance of very high concern, due to reproductive effects in humans, thus limiting its recommendation as an ideal reference toxicant. However, there is probably no other chemical for which ecotoxicity in soil has been so intensively studied; an extensive literature review yielded lethal (including avoidance) and sublethal data for 38 taxa. The ecotoxicity data were evaluated using species sensitivity distributions, collectively across all taxa, and separately according to species type, endpoints, soil type and duration. The lack of specificity in the mode of action yielded broad toxicity among soil taxa and soil types, and provided a collective approach to assessing species sensitivity, while taking into consideration differences in test methodologies and exposure durations. Toxicity was species-specific with Folsomia candida and enchytraied species demonstrating the most sensitivity; among plants, the following trend occurred: dicotyledonous (more sensitive) ≫ monocotyledonous ≫ gymnosperm species. Sensitivity was also time and endpoint specific, with endpoints such as lethality and avoidance being less sensitive than reproduction effects. Furthermore, given the breadth of data and toxicity demonstrated by boric acid, lessons learned from its evaluation are discussed to recommend the properties required by an ideal reference substance for the soil compartment.

The Efficacy of Boric Acid Used to Treat Experimental Osteomyelitis Caused by Methicillin-Resistant Staphylococcus aureus: an In Vivo Study.

PubMed

Güzel, Yunus; Golge, Umut H; Goksel, Ferdi; Vural, Ahmet; Akcay, Muruvvet; Elmas, Sait; Turkon, Hakan; Unver, Ahmet

2016-10-01

We explored the ability of local and systemic applications of boric acid (BA) to reduce the numbers of methicillin-resistant Staphylococcus aureus (MRSA) in a rat model of tibial osteomyelitis (OM), and compared boric acid with vancomycin (V). Implant-associated osteomyelitis was established in 35 rats. After 4 weeks, at which time OM was evident both radiologically and serologically in all animals, the rats were divided into five groups of equal number: group 1, control group (no local application of BA or other medication); group 2, V group; group 3, local BA + V group; group 4, local BA group; and group 5, local + systemic BA group. Serum total antioxidant status, and the levels of tumor necrosis factor (TNF)-α and interleukin (IL)-6, were measured. Pathological changes attributable to bone OM were evaluated using a grading system. Bacterial colony-forming units (CFUs) per gram of bone were counted. The lowest bacterial numbers were evident in group 3, and the bacterial numbers were significantly lower than that of the control group in all four test groups (p < 0.001). Group 3 also had the least severe bone infection (OM score 1.7 ± 1.1, p < 0.05). Upon histological and microbiological evaluation, no significant difference was evident between groups 2 and 3. Total antioxidant levels were significantly different in all treatment groups compared to the control group. Microbiological and histopathological evaluation showed that systemic or local application of BA was effective to treat OM, although supplementary V increased the effectiveness of BA.

Boric acid and salinity effects on maize roots. Response of aquaporins ZmPIP1 and ZmPIP2, and plasma membrane H+-ATPase, in relation to water and nutrient uptake.

PubMed

Martinez-Ballesta, Maria del Carmen; Bastías, Elizabeth; Zhu, Chuanfeng; Schäffner, Anton R; González-Moro, Begoña; González-Murua, Carmen; Carvajal, Micaela

2008-04-01

Under saline conditions, an optimal cell water balance, possibly mediated by aquaporins, is important to maintain the whole-plant water status. Furthermore, excessive accumulation of boric acid in the soil solution can be observed in saline soils. In this work, the interaction between salinity and excess boron with respect to the root hydraulic conductance (L(0)), abundance of aquaporins (ZmPIP1 and ZmPIP2), ATPase activity and root sap nutrient content, in the highly boron- and salt-tolerant Zea mays L. cv. amylacea, was evaluated. A downregulation of root ZmPIP1 and ZmPIP2 aquaporin contents were observed in NaCl-treated plants in agreement with the L(0) measurements. However, in the H3BO3-treated plants differences in the ZmPIP1 and ZmPIP2 abundance were observed. The ATPase activity was related directly to the amount of ATPase protein and Na+ concentration in the roots, for which an increase in NaCl- and H3BO3+ NaCl-treated plants was observed with respect to untreated and H3BO3-treated plants. Although nutrient imbalance may result from the effect of salinity or H3BO3 alone, an ameliorative effect was observed when both treatments were applied together. In conclusion, our results suggest that under salt stress, the activity of specific membrane components can be influenced directly by boric acid, regulating the functions of certain aquaporin isoforms and ATPase as possible components of the salinity tolerance mechanism.

High-compactness coating grown by plasma electrolytic oxidation on AZ31 magnesium alloy in the solution of silicate-borax

NASA Astrophysics Data System (ADS)

Shen, M. J.; Wang, X. J.; Zhang, M. F.

2012-10-01

A ceramic coating was formed on the surface of AZ31 magnesium alloy by plasma electrolytic oxidation (PEO) in the silicate solution with and without borax doped. The composition, morphology, elements and roughness as well as mechanical property of the coating were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectrometry (EDS), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and reciprocal-sliding tribometer. The results show that the PEO coating is mainly composed of magnesia. When using borax dope, boron element is permeating into the coating and the boron containing phase exist in the form of amorphous. In addition, the microhardness and compactness of the PEO coating are improved significantly due to doped borax.

Synthesis of boron nitride powders

NASA Astrophysics Data System (ADS)

Dreissig, Dirk Horst

2002-09-01

In the materials science community there is much interest in the development of new, efficient approaches for preparing ceramic powders having properties or performance characteristics not found with powders produced by traditional metallurgical synthesis methods. In this regard, aerosol-based syntheses are finding general acceptance for the preparation of non-metal and metal oxide powders. In contrast, much less effort has been given to aerosol-type syntheses for non-oxide powders despite potentially useful benefits. This dissertation describes the application of two chemical systems in aerosol assisted vapor phase synthesis (AAVS) for the preparation of spherical morphology boron oxynitride, BNxOy, powders that are subsequently converted to spherical morphology boron nitride in a second nitridation step. Chapter 1 describes the AAVS synthesis of BNxOy powders using a reaction of an aqueous boric acid containing aerosol with ammonia at 1000°C. The effect of reactor tube material, total gas flow rate, ammonia concentration, boric acid concentration, and urea addition to the boric acid aerosol on the percent oxygen composition is described. The resulting BNxOy powders contain significant amounts of oxygen that require replacement in a second stage nitridation reaction at elevated temperature under ammonia. The influences of the reaction temperature profile, crucible geometry and transformation additive on final oxygen composition and powder crystallinity are described. Chapter 2 outlines the formation of BNxOy powders from an AAVS reaction between the boron precursor (MeO)3B and ammonia. The formation of the powders is studied as a function of total gas flow rate and ammonia concentration. In all cases the resulting powders contain lower levels of oxygen compared to powders produced from aqueous boric acid aerosols. The conversion of the BNxOy powders in the second stage nitridation reaction with ammonia is examined as a function of crucible geometry, temperature profile and ammonia flow rate. In support of this process, the molecular reaction between (MeO)3B and NH3 was reexamined. The adduct, (MeO)3B·NH3, was isolated and its molecular structure determined by single crystal X-ray diffraction techniques. The results of these studies provide guidance for more detailed studies that should result in industrial scale synthesis of spherical morphology BN which currently is not formed by standard metallurgical syntheses. This new material has potential applications in several areas including the formation of BN loaded organic polymer composites.

BORAX V EXPONENTIAL EXPERIMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirn, F.S.; Hagen, J.I.

1963-04-01

The cadmium ratio was measured in an exponential mockup of Borax V as a function of the void fraction. The extent of voids, simulated by lengths of closed polyethylene tubes, ranged from 0 to 40%. The corresponding cadmium ratios ranged from 6.1 to 4.6. The exponential was also used to determine the radial flux pattern across a Borax-type fuel assembly and the fine flux detail in and around fuel rods. For a normal loading the maximum-to-average power generation across an assembly was 1.24. (auth)

Non-avoidance behaviour in enchytraeids to boric acid is related to the GABAergic mechanism.

PubMed

Bicho, Rita C; Gomes, Susana I L; Soares, Amadeu M V M; Amorim, Mónica J B

2015-05-01

Soil invertebrates, e.g. enchytraeids, are known to be able to avoid unfavourable conditions, which gives them an important ecological advantage. These organisms possess chemoreceptors that can detect stressors, which in turn activate responses such as avoidance behaviour. We studied the avoidance behaviour in response to boric acid (BA) using enchytraeids. Results showed not only no avoidance, but that increasing concentrations seemed to have an "attraction" effect. To study the underlying mechanism, a selection of genes targeting for neurotransmission pathways (acetylcholinesterase (AChE) and gamma-aminobutyric acid receptor (GABAr)) were quantified via quantitative real-time polymerase chain reaction (qPCR). Evidences were that BA is neurotoxic via the GABAergic system mechanism where it acts as a GABA-associated protein receptor (GABAAR) antagonist possibly causing anaesthetic effects. This is the first time that (non)avoidance behaviour in invertebrates was studied in relation with the GABAergic system. We strongly recommend the combination of such gene and/or functional assay studies with the avoidance behaviour test as it can bring many advantages and important interpretation lines for ecotoxicity with minor effort.

Passive safety injection system using borated water

DOEpatents

Conway, Lawrence E.; Schulz, Terry L.

1993-01-01

A passive safety injection system relies on differences in water density to induce natural circulatory flow patterns which help maintain prescribed concentrations of boric acid in borated water, and prevents boron from accumulating in the reactor vessel and possibly preventing heat transfer.

Respiratory effects of borax dust.

PubMed Central

Garabrant, D H; Bernstein, L; Peters, J M; Smith, T J; Wright, W E

1985-01-01

The relation of respiratory symptoms, pulmonary function, and abnormalities of chest radiographs to estimated exposures of borax dust has been investigated in a cross sectional study of 629 actively employed borax workers. Ninety three per cent of the eligible workers participated in the study and exposures ranged from 1.1 mg/m3 to 14.6 mg/m3. Symptoms of acute respiratory irritation such as dryness of the mouth, nose, or throat, dry cough, nose bleeds, sore throat, productive cough, shortness of breath, and chest tightness were related to exposures of 4.0 mg/m3 or more, and were infrequent at exposures of 1.1 mg/m3. Symptoms of persistent respiratory irritation meeting the definition of chronic simple bronchitis were related to exposure among non-smokers. Decrements in the FEV1 as a percentage of predicted were seen among smokers who had heavy cumulative borax exposures (greater than or equal to 80 mg/m3 years) but were not seen among less exposed smokers or among non-smokers. Radiographic abnormalities were uncommon and were not related to dust exposure. Borax dust appears to act as a simple respiratory irritant and perhaps causes small changes in the FEV1 among smokers who are heavily exposed. PMID:3878156

Effect of borax concentration on the structure of Poly(Vinyl Alcohol) gels

NASA Astrophysics Data System (ADS)

Lawrence, Mathias B.; Desa, J. A. E.; Aswal, V. K.

2012-06-01

Poly(Vinyl Alcohol) hydrogels cross-linked with varying concentrations of borax have been studied using Small-Angle Neutron Scattering and X-Ray Diffraction. The intensity of scattering increases with borax concentration from 1 mg/ml up to 2 mg/ml and falls thereafter for 4 mg/ml, increasing again for a concentration of 10 mg/ml. The mesoscopic structural changes that cause these trends in the SANS data are in keeping with the variations in the X-ray diffraction patterns pertaining to structures within the PVA chains.

Seizure disorders and anemia associated with chronic borax intoxication

PubMed Central

Gordon, A. S.; Prichard, J. S.; Freedman, M. H.

1973-01-01

During the course of investigation of two infants with seizure disorders it was discovered that both had been given large amounts of a preparation of borax and honey which resulted in chronic borate intoxication. In one child a profound anemia developed as well. The symptoms of chronic borate intoxication are different from those of the acute poisoning with which we are more familiar. The borax and honey preparations are highly dangerous and should no longer be manufactured or distributed for sale. ImagesFIG. 1FIG. 2 PMID:4691106

The Kramer deposit of southern California--Preliminary insights on the origins of zoned lacustrine evaporite borate deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swihart, G.H.; McBay, E.H.; Smith, D.H.

1992-01-01

Lacustrine evaporite borate deposits span the range from mineralogically unzoned or poorly zoned to concentrically or complexly zoned types. Deposits often contain an inner ulexite or probertite (Na-Ca borates) zone and an outer colemanite (Ca borate) zone. A few deposits contain an innermost borax (Na borate) zone. Boron isotopic analyses of core material from the zoned borax-ulexite-colemanite Kramer deposit have been made with the aim of providing a better understanding of the processes of zone formation. Samples from 6 depths over a 63 foot interval in the borax zone yield a [delta] B-11 range of +0.1 to +2.3 permil. Twomore » samples in the portion of the ulexite zone below the borax zone, vertically separated from one another by 20 feet, yield identical results of [delta]B-11 = [minus]2.1 permit. Three ulexite samples from a 10 foot interval above the borax zone produced results in the range [delta]B-11 = [minus]4.6 to [minus]5.5 permil. A number of possible origins for ulexite at Kramer have been proposed: (1) primary precipitation from the lake brines; (2) postdepositional alteration of the borax zone margin by Ca-rich groundwater; (3) mixing of seeping lake brines and Ca-rich groundwater in muds around the lake. Given the small variation in B isotopic composition exhibited in the borax zone, mechanisms 1 and 2 would produce upper and lower portions of the ulexite zone with similar isotopic compositions. In the third scenario, the difference in composition of the upper and lower ulexites could be due to distance from the lake and relative proportions of seeped lake brine (B-11-rich) and clay adsorbed B (B-10-rich). Furthermore, the cotton ball form of the ulexite in this core is identical to that of ulexite forming today just beneath the surface of dry lakes in NV and CA.« less

Crystallization kinetics of the borax decahydrate

NASA Astrophysics Data System (ADS)

Ceyhan, A. A.; Sahin, Ö.; Bulutcu, A. N.

2007-03-01

The growth and dissolution rates of borax decahydrate have been measured as a function of supersaturation for various particle sizes at different temperature ranges of 13 and 50 °C in a laboratory-scale fluidized bed crystallizer. The values of mass transfer coefficient, K, reaction rate constant, kr and reaction rate order, r were determined. The relative importances of diffusion and integration resistance were described by new terms named integration and diffusion concentration fraction. It was found that the overall growth rate of borax decahydrate is mainly controlled by integration (reaction) steps. It was also estimated that the dissolution region of borax decahydrate, apart from other materials, is controlled by diffusion and surface reaction. Increasing the temperature and particle size cause an increase in the values of kinetic parameters ( Kg, kr and K). The activation energies of overall, reaction and mass transfer steps were determined as 18.07, 18.79 and 8.26 kJmol -1, respectively.

Long-Endurance Maritime Surveillance with Ocean Glider Networks

DTIC Science & Technology

2015-09-01

response to fluid viscosity , as well as magnesium sulfate and boric acid molecules found in seawater (Francois and Garrison 1982). As a result, its...Hemipelagic Terrigenous Clay ) is derived from the Bottom Sediment Type (BST) database maintained by the U.S. Naval Oceanographic Office Acoustics

Experiments with "Calo-ph Meter."

ERIC Educational Resources Information Center

Paris, Michel R.; Aymes, Daniel J.

1990-01-01

The principles and procedures for three enthalpimetric measurement experiments including a determination of the water equivalent mass of the calorimeter, the calibration of the instrument, and determination of the dissociation heat of boric acid performed with a teacher-made instrument are presented. Suggestions for further experiments are…

Preservation Using Pesticides: Some Words of Caution.

ERIC Educational Resources Information Center

Davis, Mary

1985-01-01

Addresses problem of insects and other pests in library facility and material maintenance. Highlights include dangers of chemical pesticides; alternative methods for treatment of book infestations (light and temperature regulation, freezing, establishment of low oxygen atmosphere, microwaves and radiation, boric acid); and state and federal laws…

Action of boron at the molecular level: effects on transcription and translation in an acellular system.

PubMed

Dzondo-Gadet, M; Mayap-Nzietchueng, R; Hess, K; Nabet, P; Belleville, F; Dousset, B

2002-01-01

It has been shown that boric acid has well-defined biological effects such as stimulation of wound healing in vivo, release of growth factors and cytokines, and increase of the extracellular matrice turnover. We examined its action at the molecular level, using cell-free systems of transcription (isolated placenta nuclei) and translation (wheat germ extract). We found that 10 mM boric acid greatly increased RNA synthesis, measured by absorbance at 260 nm (x 6.4) or by [3H]-UTP uptake (x 11). Full-length functional mRNA was produced because proteins of 14-80 kDa were translated. Among these proteins, factors involved in angiogenesis and, subsequently, in wound healing (VEGF and TGFbeta) were identified by slot blot, whereas growth factors such as FGF1 and TNFalpha were not detected. These results demonstrate that boron may contribute to biological cell activities at both the transcription and translation levels. However, the mechanism of action is still not known.

Synthesizing and characterization of titanium diboride for composite bipolar plates in PEM fuel cell

NASA Astrophysics Data System (ADS)

Duddukuri, Ramesh

This research deals with the synthesis and characterization of titanium diboride (TiB2) from novel carbon coated precursors. This work provides information on using different boron sources and their effect on the resulting powders of TiB2. The process has two steps in which the oxide powders were first coated with carbon by cracking of a hydrocarbon gas, propylene (C3H6) and then, mixed with boron carbide and boric acid powders in a stoichiometric ratio. These precursors were treated at temperatures in the range of 1200--1400° C for 2 h in flowing Argon atmosphere to synthesize TiB2. The process utilizes a carbothermic reduction reaction of novel carbon coated precursor that has potential of producing high-quality powders (sub-micrometer and high purity). Single phase TiB2 powders produced, were compared with commercially available titanium diboride using X-ray diffraction and Transmission electron microscopy obtained from boron carbide and boric acid containing carbon coated precursor.

Enhanced Emission from Li2CaSiO4:Dy3+ Phosphors by Doping with Al3+ and B3+

NASA Astrophysics Data System (ADS)

Erdoğmuş, E.

2016-05-01

Pure Li2CaSiO4, Li2CaSiO4:Dy3+ and Al3+, B3+ co-doped materials were prepared by a solid-state reaction in air at 900°C for 6 h and characterized by using powder XRD. The luminescence properties of the synthesized phosphors were measured at room temperature with a spectrofluorometer. Li2CaSiO4:Dy3+ emits at 484, 575, and 660 nm upon 352 nm excitation. The emission spectrum intensity of Dy3+ increased from 0.01 to 0.06 mol.%, and beyond 0.06 mol.%, concentration quenching was observed. Also, in this study, the effects of boric acid and aluminum oxide concentration on the photoluminescence properties of Dy3+ doped phosphors were investigated. The results showed that boric acid and aluminum oxide were effective in improving the photoluminescence intensity of Li2CaSiO4:Dy3+ compounds.

The effects of boric acid on sister chromatid exchanges and chromosome aberrations in cultured human lymphocytes.

PubMed

Arslan, Mehmet; Topaktas, Mehmet; Rencuzogullari, Eyyüp

2008-02-01

The aim of this study was to determine the possible genotoxic effects of boric acid (BA) (E284), which is used as an antimicrobial agent in food, by using sister chromatid exchange (SCEs) and chromosome aberration (CAs) tests in human peripheral lymphocytes. The human lymphocytes were treated with 400, 600, 800, and 1000 mug/mL concentrations of BA dissolved in dimethyl sulfoxide (DMSO), for 24 h and 48 h treatment periods. BA did not increase the SCEs for all the concentrations and treatment periods when compared to control and solvent control (DMSO). BA induced structural and total CAs at all the tested concentrations for 24 and 48 h treatment periods. The induction of the total CAs was dose dependent for the 24 h treatment period. However, BA did not cause numerical CAs. BA showed a cytotoxic effect by decreasing the replication index (RI) and mitotic index (MI). BA decreased the MI in a dose-dependent manner for the 24 h treatment period.

Luminescence properties of Eu 3+ and Sm 3+ coactivated Gd(III) tungstate phosphor for light-emitting diodes

NASA Astrophysics Data System (ADS)

Wei, Qiong; Chen, Donghua

2009-09-01

Rare-earth ions coactivated red phosphors Gd 0.2RE 1.8(WO 4) 3 (RE=Eu 3+ and Sm 3+) were synthesized by conventional solid-state reaction using boric acid as a flux agent. The samples were characterized by X-ray diffractometer (XRD), energy-dispersive X-ray spectrometer (EDS) and luminescence spectrometer (LS). The results showed that the Eu-Sm system exhibits higher emission intensity than those of the Eu single-doped system and Sm separate-doped system under ultraviolet (UV) radiation. Samarium(III) ions are effective in broadening and strengthened absorptions around 400 nm. Furthermore, it exhibits enhanced luminescence emission. when the mole ratio of boric acid is about 0.16, the luminescence capability is optimum. Two strongest lines at ultraviolet (394 nm) and blue (465 nm) in excitation spectra of these phosphors match well with the output wavelengths of UV and blue GaN-based light-emitting diodes (LEDs) chips.

Influence of Chloride Ions as Contaminants on the Corrosion Behavior of Alloy 718 in Pool Water of Nuclear Power Plants

NASA Astrophysics Data System (ADS)

Hugues, Jonathan; Andrieu, Eric; Blanc, Christine; Cloué, Jean-Marc

The electrochemical behavior of alloy 718 in a chloride-containing boric acid solution was studied to determine the influence of chloride ions as contaminants of pool water of nuclear power plants on the corrosion behavior of the alloy. Experiments were performed at 20°C and 60°C with chloride concentrations from 1.5 to 15 000 ppm, using stationary measurements i.e. OCP versus time measurements and plotting of current-potential curves. After the electrochemical tests, the samples were observed using optical microscopy. Immersion tests in chloride-containing boric acid solutions were also carried out: samples were immersed for a time as long as 17 weeks at open circuit potential and their residual mechanical properties were measured. Results showed that, whatever the chloride concentration, there was no corrosion for samples immersed at open circuit potential. However, when the samples were polarized at high potentials, intergranular corrosion might be observed in occluded zones.

Controlling the Morphology and Oxidation Resistance of Boron Carbide Synthesized Via Carbothermic Reduction Reaction

NASA Astrophysics Data System (ADS)

Ahmed, Yasser M. Z.; El-Sheikh, Said M.; Ewais, Emad M. M.; Abd-Allah, Asmaa A.; Sayed, Said A.

2017-03-01

Boron carbide powder was synthesized from boric acid and lactose mixtures via easy procedure. Boric acid and lactose solution mixtures were roasted in stainless steel pot at 280 °C for 24 h. Boron carbide was obtained by heating the roasted samples under flowing of industrial argon gas at 1500 °C for 3 h. The amount of borate ester compound in the roasted samples was highly influenced by the boron/carbon ratio in the starting mixtures and plays a versatile role in the produced boron carbide. The high-purity boron carbide powder was produced with a sample composed of lowest boron/carbon ratio of 1:1 without calcination step. Particle morphology was changed from nano-needles like structure of 8-10 nm size with highest carbon ratio mixture to spherical shape of >150 nm size with lowest one. The oxidation resistance performance of boron carbide is highly dependent on the morphology and grain size of the synthesized powder.

GDP-D-mannose epimerase regulates male gametophyte development, plant growth and leaf senescence in Arabidopsis.

PubMed

Qi, Tiancong; Liu, Zhipeng; Fan, Meng; Chen, Yan; Tian, Haixia; Wu, Dewei; Gao, Hua; Ren, Chunmei; Song, Susheng; Xie, Daoxin

2017-09-04

Plant GDP-D-mannose epimerase (GME) converts GDP-D-mannose to GDP-L-galactose, a precursor of both L-ascorbate (vitamin C) and cell wall polysaccharides. However, the genetic functions of GME in Arabidopsis are unclear. In this study, we found that mutations in Arabidopsis GME affect pollen germination, pollen tube elongation, and transmission and development of the male gametophyte through analysis of the heterozygous GME/gme plants and the homozygous gme plants. Arabidopsis gme mutants also exhibit severe growth defects and early leaf senescence. Surprisingly, the defects in male gametophyte in the gme plants are not restored by L-ascorbate, boric acid or GDP-L-galactose, though boric acid rescues the growth defects of the mutants, indicating that GME may regulate male gametophyte development independent of L-ascorbate and GDP-L-galactose. These results reveal key roles for Arabidopsis GME in reproductive development, vegetative growth and leaf senescence, and suggest that GME regulates plant growth and controls male gametophyte development in different manners.

Borax spends $30M for cogeneration system. [US Borax and Chemical Corp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barber, J.

1982-09-20

A $30 million natural-gas-fired turbine power plant will provide all the electricity and steam needed at the US Borax and Chemical Corp. plant in Los Angeles. The cogeneration facility will come on line in 1984, and will pay for itself in about five years. The plant will use only half the 46 megawatts produced, the 22 megawatt surplus being sold to Southern California Edison Co. on a 20-year contract at a price pegged to the utility's avoided costs. Natural gas consumption at the plant will remain about the same. (DCK)

DESIGN AND HAZARDS SUMMARY REPORT, BOILING REACTOR EXPERIMENT V (BORAX V)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1961-05-01

Design data for BORAX V are presented along with results of hazards evaluation studies. Considcration of the hazards associated with the operation of BORAX V was based on the following conditions: For normal steady-state power and experimental operation, the reactor and plant are adequately shielded and ventilated to allow personnel to be safely stationed in the turbine building and on the main floor of the reactor building. The control building is located one- half mile distant from the reactor building. For special, hazardous experiments, personnel are withdrawn from the reactor area. (M.C.G.)

Quantitative extraction and concentration of synthetic water-soluble acid dyes from aqueous media using a quinine-chloroform solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kobayashi, F.; Ozawa, N.; Hanai, J.

Twenty-one water-soluble acid dyes, including eleven azo, five triphenylmethane four xanthene, one naphthol derivatives, used at practical concentrations for food coloration, were quantitatively extracted from water and various carbonated beverages into a 0.1 M quinine-chloroform solution in the presence of 0.5 M boric acid by brief shaking. Quantitative extraction of these dyes was also accomplished by the 0.1 M quinine-chloroform solution made conveniently from chloroform, quinine hydrochloride, and sodium hydroxide added successively to water or beverages containing boric acid. Quinine acted as a countercation on the dyes having sulfonic and/or carboxylic acid group(s) to form chloroform-soluble ion-pair complexes. The diacidicmore » base alkaloid interacted with each acid group of mono-, di-, tri-, and tetrasulfonic acid dyes approximately in the ratio 0.8-0.9 to 1. The dyes in the chloroform solution were quantitatively concentrated into a small volume of sodium hydroxide solution also by brief shaking. The convenient quinine-chloroform method was applicable to the quantitative extraction of a mixture of 12 dyes from carbonated beverages, which are all currently used for food coloration. A high-pressure liquid chromatographic method is also presented for the systematic separation and determination of these 12 dyes following their concentration into the aqueous alkaline solution. The chromatogram was monitored by double-wavelength absorptiometry in the visible and ultraviolet ray regions.« less

Methylboronic acid fertilization alleviates boron deficiency symptoms in Arabidopsis thaliana.

PubMed

Duran, Catherine; Arce-Johnson, Patricio; Aquea, Felipe

2018-07-01

Our results showed that methylboronic acid is capable of alleviating boron deficiency, enhancing plant growth, and is less toxic than boric acid at higher concentrations. Boron is an essential plant micronutrient and its deficiency occurs in several regions globally, resulting in impaired plant growth. Boron fertilization is a common agricultural practice, but the action range of boron is narrow, sharply transitioning from deficiency to toxicity. Boric acid (BA) is the most common chemical form used in agriculture. In this work, we describe that methylboronic acid (MBA) is capable of alleviating boron deficiency in Arabidopsis. MBA is a boronic acid, but does not naturally occur in soils, necessitating synthesis. Other boronic acids have been described as boron competitors in plants, inhibiting auxin biosynthesis and root development. MBA is more water-soluble than BA and delivers the same amount of boron per molecule. We observed that Arabidopsis seedlings grown in the presence of MBA presented higher numbers of lateral roots and greater main root length compared to plants grown in BA. In addition, root hair length and leaf surface area were increased using MBA as a boron fertilizer. Finally, MBA was less toxic than BA at high concentrations, producing a slight reduction in the main root length but no decrease in total chlorophyll. Our results open a new opportunity to explore the use of a synthetic form of boron in agriculture, providing a tool for future research for plant nutrition.

Setting retarding composition for well cementing and recementing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poblano, R.

1979-01-30

The present invention relates to an improved composition that retards setting in the cementing and recementing of oil well casings, which can be applied at depths that vary between 13,123.4 and 21,325.5 ft. The retarding composition is constituted by the following ingredients: sodium or potassium carboxymethylcellulose; sodium tetraborate and Dextrine, it being characterized in that it also contains an inorganic acid such as boric acid.

Different therapeutic strategies for burning mouth syndrome: preliminary data.

PubMed

Marino, Roberto; Torretta, Sara; Capaccio, Pasquale; Pignataro, Lorenzo; Spadari, Francesco

2010-09-01

To compare different therapeutic supportive approaches in patients with burning mouth syndrome. A prospective study was carried out for this purpose. The study involved 56 patients with burning mouth syndrome. They were randomly assigned to treatment with capsaicin, alpha-lipoic acid or lysozyme-lactoperoxidase (test drugs) or boric acid (control group). Symptoms were scored after 60 days treatment and 60 days after drug discontinuation. At the end of the treatment period, there was a significant reduction in the symptom scores of all of the patients who received the test drugs (P<0.01), and at the end of the follow-up period in the test groups as a whole (P<0.01); the reduction was not significant when considering each test group separately after the treatment period. All of the treatments were more effective than boric acid and there was no significant difference in the symptom scores of the control group at either of the study time-points. Our results demonstrate the similar effectiveness of capsaicin and alpha-lipoic acid in controlling the symptoms of burning mouth syndrome. Lysozyme-lactoperoxidase may be effective in the supportive care of BMS patients with xerostomia. The transitory effect observed after discontinuing drug administration justifies the use of prolonged therapy in chronically affected patients. © 2010 John Wiley & Sons A/S.

A method for determining the composition of methanol-trimethyl borate mixtures

NASA Technical Reports Server (NTRS)

Kaye, Samuel; Sordyl, Frank

1955-01-01

A study of mixtures of pure methanol and trimethyl borate showed that the composition can be accurately obtained by a simple density determination. The refractive-index determination gives the composition with much less accuracy. The potentiometric titration of boric acid is also discussed.

Epoxy-borax-coal tar composition for a radiation protective, burn resistant drum liner and centrifugal casting method

DOEpatents

Taylor, Robert S.; Boyer, Norman W.

1980-01-01

A boron containing burn resistant, low level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source. The material is basically composed of Borax in the range of 25-50%, coal tar in the range of 25-37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% Borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications.

Influent of Borax Decahydrate Composition as Additional Flux into Stoneware Bodies

NASA Astrophysics Data System (ADS)

Bakil, Siti Natrah Abd; Hussin, Rosniza; Bakar Aramjat, Abu

2017-08-01

Stoneware is vitrified, has less porosity and requires high sintering temperature. The influent of borax decahydrate composition at sintering temperature 1050°C and 1150°C on the thermal analysis, fracture surface, linear shrinkage, water absorption and modular of rapture (MOR) were investigated. Rectangular sample were produced by uniaxially pressing at 40MPa. The thermal behavior was determined by thermogravimetric and different thermal analysis (TGA-DTA). The Scanning electron microscopy (SEM) was used for fracture surface analysis. The water absorption (%) of the sample were determined using Archimedes’ method. The experimental result showed that content of borax decahydrate have influent the properties of stoneware bodies.

Epoxy-borax-coal tar composition for a radiation protective, burn resistant drum liner and centrifugal casting method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyer, N.W.; Taylor, R.S.

1980-10-28

A boron containing burn resistant, low level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source. The material is basically composed of borax in the range of 25-50%, coal tar in the range of 25-37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications.

Comparison of PrestoBlue® and plating method to evaluate antimicrobial activity of ascorbic acid, boric acid and curcumin in an in vitro gastrointestinal model.

PubMed

Hernandez-Patlan, D; Solis-Cruz, B; Méndez-Albores, A; Latorre, J D; Hernandez-Velasco, X; Tellez, G; López-Arellano, R

2018-02-01

To compare the conventional plating method vs a fluorometric method using PrestoBlue ® as a dye by determining the antimicrobial activity of two organic acids and curcumin (CUR) against Salmonella Enteritidis in an avian in vitro digestion model that simulates the crop, proventriculus and intestine. A concentration of 10 8  CFU per ml of S. Enteritidis was exposed to groups with different rates of ascorbic acid (AA), boric acid (BA) and CUR. Significant differences were observed when the means of the treatments were compared with the controls in the compartments that simulate the crop and intestine (P < 0·05). Ascorbic acid alone and high rates of AA in the mixtures were the most efficient treatments in the crop compartment. However, in the intestinal compartment BA alone and at different rates in the mixture BA-CUR (1 : 1) were the best treatments to decrease the concentration of S. Enteritidis. The results of this study suggest that there could be an antagonistic bactericidal effect between AA and CUR and AA and BA as well as a synergistic bactericidal effect between BA and CUR. These findings may contribute to the development of a formulation with microencapsulated compounds to liberate them in different compartments to combat S. Enteritidis infections in broiler chickens. © 2017 The Society for Applied Microbiology.

Using Greener Gels to Explore Rheology

ERIC Educational Resources Information Center

Garrett, Brendan; Matharu, Avtar S.; Hurst, Glenn A.

2017-01-01

A laboratory experiment was developed to investigate the rheological properties of a green calcium-cross-linked alginate gel as an alternative to the traditional borax-cross-linked poly(vinyl alcohol) gel. As borax is suspected of damaging fertility and the unborn child, a safe, green alternative is necessary. The rheological properties of a…

Alkaline Anaerobic Respiration: Isolation and Characterization of a Novel Alkaliphilic and Metal-Reducing Bacterium

PubMed Central

Ye, Qi; Roh, Yul; Carroll, Susan L.; Blair, Benjamin; Zhou, Jizhong; Zhang, Chuanlun L.; Fields, Matthew W.

2004-01-01

Iron-reducing enrichments were obtained from leachate ponds at the U.S. Borax Company in Boron, Calif. Based on partial small-subunit (SSU) rRNA gene sequences (approximately 500 nucleotides), six isolates shared 98.9% nucleotide identity. As a representative, the isolate QYMF was selected for further analysis. QYMF could be grown with Fe(III)-citrate, Fe(III)-EDTA, Co(III)-EDTA, or Cr(VI) as electron acceptors, and yeast extract and lactate could serve as electron donors. Growth during iron reduction occurred over the pH range of 7.5 to 11.0 (optimum, pH 9.5), a sodium chloride range of 0 to 80 g/liter (optimum, 20 g/liter), and a temperature range of 4 to 45°C (optimum, approximately 35°C), and iron precipitates were formed. QYMF was a strict anaerobe that could be grown in the presence of borax, and the cells were straight rods that produced endospores. Sodium chloride and yeast extract stimulated growth. Phylogenetic analysis of the SSU rRNA gene indicated that the bacterium was a low-G+C gram-positive microorganism and had 96 and 92% nucleotide identity with Alkaliphilus transvaalensis and Alkaliphilus crotonatoxidans, respectively. The major phospholipid fatty acids were 14:1, 16:1ω7c, and 16:0, which were different from those of other alkaliphiles but similar to those of reported iron-reducing bacteria. The results demonstrated that the isolate might represent a novel metal-reducing alkaliphilic species. The name Alkaliphilus metalliredigens sp. nov. is proposed. The isolation and activity of metal-reducing bacteria from borax-contaminated leachate ponds suggest that bioremediation of metal-contaminated alkaline environments may be feasible and have implications for alkaline anaerobic respiration. PMID:15345448

Development of Toxicity Benchmarks for Nitrogen-based Energetic Materials for the Enchytraeid Worm, Enchytraeus crypticus

DTIC Science & Technology

2013-11-01

pp 177–182. Anzhi, Z.L.; Marx, K.A.; Walker, J.; Kaplan, D.L. Trinitrotoluene and Metabolites Binding to Humic Acid . Environ. Sci. Technol. 1997...2001, pp 293–312. Thorn, K.A.; Kennedy, K.R. 15 N NMR Investigation of the Covalent Binding of Reduced TNT Amines to Soil Humic Acid , Model...9 3.2 Toxicity of Reference Toxicant, Boric Acid , to the Potworm E. crypticus ......15 3.3 Effects of 2,4-DNT on the Potworm E. crypticus

Photostabilization of ascorbic acid with citric acid, tartaric acid and boric acid in cream formulations.

PubMed

Ahmad, I; Ali Sheraz, M; Ahmed, S; Shad, Z; Vaid, F H M

2012-06-01

This study involves the evaluation of the effect of certain stabilizers, that is, citric acid (CT), tartaric acid (TA) and boric acid (BA) on the degradation of ascorbic acid (AH(2) ) in oil-in-water cream formulations exposed to the UV light and stored in the dark. The apparent first-order rate constants (0.34-0.95 × 10(-3) min(-1) in light, 0.38-1.24 × 10(-2) day(-1) in dark) for the degradation reactions in the presence of the stabilizers have been determined. These rate constants have been used to derive the second-order rate constants (0.26-1.45 × 10(-2) M(-1) min(-1) in light, 3.75-8.50 × 10(-3) M(-1) day(-1) in dark) for the interaction of AH(2) and the individual stabilizers. These stabilizers are effective in causing the inhibition of the rate of degradation of AH(2) both in the light and in the dark. The inhibitory effect of the stabilizers is in the order of CT > TA > BA. The rate of degradation of AH(2) in the presence of these stabilizers in the light is about 120 times higher than that in the dark. This could be explained on the basis of the deactivation of AH(2) -excited triplet state by CT and TA and by the inhibition of AH(2) degradation through complex formation with BA. AH(2) leads to the formation of dehydroascorbic acid (A) by chemical and photooxidation in cream formulations. © 2012 The Authors. ICS © 2012 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

CRITICAL EXPERIMENT WITH BORAX-V. Internal Superheater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plumlee, K.E.; Baird, Q.L.; Stanford, G.S.

1963-11-01

A critical experiment was performed with 12 BORAX-V superheater subassemblies in a central voidable region plus 1228 to 1525 UO/sub 2/ fuel pins (3 wt% enriched) in a peripheral region. Removing water (28% of superheater volume) at room temperature decreased reactivity by 2.2%. The midplane (two- dimensional) peak-to-average power distribution in the voided superheater was approximately 1.24, mostly attributable to flux depressions within insulated fuel boxes. Cadmium ratios are also reported. The experiment was initiated to supplement computational information which might have affected plans for loading the superheater zone into the BORAX-V reactor. No changes were indicated by the experiment.more » (auth)« less

Fire and bending properties of blockboard with fire retardant treated veneers

Treesearch

T. Laufenberg; N. Ayrilmis; R. White

2006-01-01

This study evaluated fire and bending properties of blockboards with various fire retardant treated veneers. Blockboards were manufactured using untreated fir strips and sandwiched between treated ekaba veneers at final assembly. The veneers were treated with either boric acid (BA), disodium octoborate tetrahydrate (DOT), alumina trihydrate (ATH), or a BA/DOT mixture....

Synthesis and evaluation of dioctylaminoborate in wood for brown rot decay protection

Treesearch

George C. Chen; Rebecca E. Ibach

2010-01-01

This study evaluated dioctylaminoborate in wood for fungal decay protection Dioctylaminoborate was synthesized by refluxing dioctylamine and boric acid in 1:1 molar ratio in ethanol for 4 h. The product was characterized by proton Nuclear Magnetic Resonance Spectrophotometry (1H-NMR) and Fourier Transform Infrared Spectrophotometry (FTIR)....

Accumulation and loss of arsenic and boron, alone and in combination, in mallard ducks

USGS Publications Warehouse

Pendleton, G.W.; Whitworth, M.R.; Olsen, Glenn H.

1995-01-01

Study was conducted at the Patuxent Wildlife Research Center from June to October 1987. Adult mallard ducks were exposed to dietary concentrations of arsenic as sodium arsenate, boron as boric acid, or both; tissue accumulation and loss rates were estimated when the ducks were returned to uncontaminated food.

Investigations on high speed machining of EN-353 steel alloy under different machining environments

NASA Astrophysics Data System (ADS)

Venkata Vishnu, A.; Jamaleswara Kumar, P.

2018-03-01

The addition of Nano Particles into conventional cutting fluids enhances its cooling capabilities; in the present paper an attempt is made by adding nano sized particles into conventional cutting fluids. Taguchi Robust Design Methodology is employed in order to study the performance characteristics of different turning parameters i.e. cutting speed, feed rate, depth of cut and type of tool under different machining environments i.e. dry machining, machining with lubricant - SAE 40 and machining with mixture of nano sized particles of Boric acid and base fluid SAE 40. A series of turning operations were performed using L27 (3)13 orthogonal array, considering high cutting speeds and the other machining parameters to measure hardness. The results are compared among the different machining environments, and it is concluded that there is considerable improvement in the machining performance using lubricant SAE 40 and mixture of SAE 40 + boric acid compared with dry machining. The ANOVA suggests that the selected parameters and the interactions are significant and cutting speed has most significant effect on hardness.

Preparation and characterization of magnesium borate for special glass

NASA Astrophysics Data System (ADS)

Dou, Lishuang; Zhong, Jianchu; Wang, Hongzhi

2010-05-01

Magnesium borate with a variety of B2O3/MgO molar ratios, which can be applied for special glass, has been prepared through the reaction of light-burned magnesia with boric acid by a hydrothermal method. The effects of the B2O3/MgO molar ratio of raw materials, reaction time, temperature and liquid to solid ratio (ml g-1) on the synthetic product are investigated. The XRD and TG-DTG analyses indicate that the prepared magnesium borate is a mixture of magnesium hexaborate hydrate and ascharite. The results show that high B2O3/MgO molar ratios of raw materials and low reaction liquid-solid ratios favour the product with a high B2O3/MgO molar ratio and vice versa. There exists free MgO in the product when the reaction temperature is below 140 °C or the reaction time is not enough, because of the incomplete reaction of magnesium oxide with boric acid. The process of fractional crystallization for the magnesium borate mixture is also discussed.

Small amount of water induced preparation of several morphologies for InBO3:Eu3+ phosphor via a facile boric acid flux method and their luminescent properties

NASA Astrophysics Data System (ADS)

Ding, Wen; Liang, Pan; Liu, Zhi-Hong

2017-05-01

Four kinds of morphologies for InBO3:Eu3+ phosphor have been prepared via a facile boric acid flux method only by adjusting the small amount of added water. The prepared samples have been characterized by XRD, FT-IR, and SEM. It was found that the size and morphology of the samples could be effectively controlled by adjusting reaction temperature, reaction time, especially the small amount of added water, which plays an extremely critical role in the controlling morphology. The possible growth mechanisms for microsphere and flower-like morphologies were further discussed on the basis of time-dependent experiments. Furthermore, the luminescence properties of prepared InBO3:Eu3+ samples have been investigated by photoluminescence (PL) spectra. The results show that the InBO3:Eu3+ phosphors show strong orange emissions under ultraviolet excitation at 237 nm. The monodisperse microsphere sample possesses the highest PL intensity among above four morphologies, which can be used as a potential orange luminescent material.

Laser ablation molecular isotopic spectroscopy (LAMIS) towards the determination of multivariate LODs via PLS calibration model of 10B and 11B Boric acid mixtures

NASA Astrophysics Data System (ADS)

Harris, C. D.; Profeta, Luisa T. M.; Akpovo, Codjo A.; Johnson, Lewis; Stowe, Ashley C.

2017-05-01

A calibration model was created to illustrate the detection capabilities of laser ablation molecular isotopic spectroscopy (LAMIS) discrimination in isotopic analysis. The sample set contained boric acid pellets that varied in isotopic concentrations of 10B and 11B. Each sample set was interrogated with a Q-switched Nd:YAG ablation laser operating at 532 nm. A minimum of four band heads of the β system B2∑ -> Χ2∑transitions were identified and verified with previous literature on BO molecular emission lines. Isotopic shifts were observed in the spectra for each transition and used as the predictors in the calibration model. The spectra along with their respective 10/11B isotopic ratios were analyzed using Partial Least Squares Regression (PLSR). An IUPAC novel approach for determining a multivariate Limit of Detection (LOD) interval was used to predict the detection of the desired isotopic ratios. The predicted multivariate LOD is dependent on the variation of the instrumental signal and other composites in the calibration model space.

SEPARATION OF AMERICIUM FROM PROMETHIUM

DOEpatents

Pressly, R.E.

1959-07-01

Promethium-147 is separated from americium in acidic aqueous solution by adding fluosilicic acid to the solution, heating the solution to form a promethium precipitate and separating the precipitate from solution. The precipitate is then re-dissolved by ihe addition of boric acid and nitric acid, and re-precipitated by the addition of fluosilicic acid. This procedure is repeated six or more times to obtain a relatively americium-free promeihium precipitate. Americium may be separately recovered from the supernatant liquids. This process is applicable to the recovery of promethium from fission-product solutions which have been allowed to decay for a period of two to four years.

Dispersion of borax in plastic is excellent fire-retardant heat insulator

NASA Technical Reports Server (NTRS)

Evans, H.; Hughes, J.; Schmitz, F.

1967-01-01

A mix of borax powder and a chlorinated anhydrous polyester resin yields a plastic composition that is fire-retardant, yields a minimum of toxic gases when heated, and exhibits high thermal insulating properties. This composition can be used as a coating or can be converted into laminated or cast shapes.

Beneficiation of borax by reverse flotation in boron saturated brine.

PubMed

Cafer Cilek, Emin; Uresin, Hasan

2005-10-15

Flotation is one of the plausible methods for recovering borax fines discharged as fine waste to the tailings dam in the Kirka borax processing plant. A literature review dealing with the flotation behavior of boron minerals reveals that clay minerals in the boron ores coat boron minerals and thus deteriorate the quality of boron concentrates produced by direct flotation. The main objective of this study is therefore to recover borax fines from the tailings of the concentrator by reverse flotation. A three-level-factor experimental design was used to determine the main and interaction effects of variables selected on the metallurgical performance of reverse flotation. An analysis of variance for experimental results indicates that interaction effects of the variables for concentrate quality and recovery of B2O3 is nonsignificant and the most important variable for grade of concentrate and recovery is the collector dosage. It is shown that a concentrate assaying 11.25% B2O3 with 89.90% B2O3 recovery could be produced by means of single-stage (rougher) reverse flotation. Additionally, in order to produce a sufficient-quality concentrate, a multistage reverse flotation scheme involving rougher, scavenger, and two cleaners was devised. A final concentrate containing 23.47% B2O3 with 81.78% B2O3 recovery was obtained from these tests. The reverse flotation method can be thus considered as an important option for the beneficiation of borax fines.

Single-step synthesis of crystalline h-BN quantum- and nanodots embedded in boron carbon nitride films

NASA Astrophysics Data System (ADS)

Matsoso, Boitumelo J.; Ranganathan, Kamalakannan; Mutuma, Bridget K.; Lerotholi, Tsenolo; Jones, Glenn; Coville, Neil J.

2017-03-01

Herein we report on the synthesis and characterization of novel crystalline hexagonal boron nitride (h-BN) quantum- and nanodots embedded in large-area boron carbon nitride (BCN) films. The films were grown on a Cu substrate by an atmospheric pressure chemical vapour deposition technique. Methane, ammonia, and boric acid were used as precursors for C, N and B to grow these few atomic layer thick uniform films. We observed that both the size of the h-BN quantum/nanodots and thickness of the BCN films were influenced by the vaporization temperature of boric acid as well as the H3BO3 (g) flux over the Cu substrate. These growth conditions were easily achieved by changing the position of the solid boric acid in the reactor with respect to the Cu substrate. Atomic force microscope (AFM) and TEM analyses show a variation in the h-BN dot size distribution, ranging from nanodots (˜224 nm) to quantum dots (˜11 nm) as the B-source is placed further away from the Cu foil. The distance between the B-source and the Cu foil gave an increase in the C atomic composition (42 at% C-65 at% C) and a decrease in both B and N contents (18 at% B and 14 at% N to 8 at% B and 7 at% N). UV-vis absorption spectra showed a higher band gap energy for the quantum dots (5.90 eV) in comparison with the nanodots (5.68 eV) due to a quantum confinement effect. The results indicated that the position of the B-source and its reaction with ammonia plays a significant role in controlling the nucleation of the h-BN quantum- and nanodots. The films are proposed to be used in solar cells. A mechanism to explain the growth of h-BN quantum/nanodots in BCN films is reported.

Evaluation of processed borax as antidote for aconite poisoning.

PubMed

Sarkar, Prasanta Kumar; Prajapati, Pradeep K; Shukla, Vinay J; Ravishankar, Basavaiah

2017-06-09

Aconite root is very poisonous; causes cardiac arrhythmias, ventricular fibrillation and ventricular tachycardia. There is no specific antidote for aconite poisoning. In Ayurveda, dehydrated borax is mentioned for management of aconite poisoning. The investigation evaluated antidotal effect of processed borax against acute and sub-acute toxicity, cardiac toxicity and neuro-muscular toxicity caused by raw aconite. For acute protection Study, single dose of toxicant (35mg/kg) and test drug (22.5mg/kg and 112.5mg/kg) was administered orally, and then 24h survival of animals was observed. The schedule was continued for 30 days in sub-acute protection Study with daily doses of toxicant (6.25mg/kg), test drug (22.5mg/kg and 112.5mg/kg) and vehicle. Hematological and biochemical tests of blood and serum, histopathology of vital organs were carried out. The cardiac activity Study was continued for 30 days with daily doses of toxicant (6.25mg/kg), test drug (22.5mg/kg), processed borax solution (22.5mg/kg) and vehicle; ECG was taken after 1h of drug administration on 1 TB , 15th and on 30th day. For neuro-muscular activity Study, the leech dorsal muscle response to 2.5µg of acetylcholine followed by response of toxicant at 25µg and 50µg doses and then response of test drug at 25µg dose were recorded. Protection index indicates that treated borax gave protection to 50% rats exposed to the lethal dose of toxicant in acute protection Study. Most of the changes in hematological, biochemical parameters and histopathological Study induced by the toxicant in sub-acute protection Study were reversed significantly by the test drug treatment. The ventricular premature beat and ventricular tachyarrhythmia caused by the toxicant were reversed by the test drug indicate reversal of toxicant induced cardio-toxicity. The acetylcholine induced contractions in leech muscle were inhibited by toxicant and it was reversed by test drug treatment. The processed borax solution is found as an effective protective agent to acute and sub-acute aconite poisoning, and aconite induced cardiac and neuro-muscular toxicity. Processed borax at therapeutic dose (22.5mg/kg) has shown better antidotal activity profile than five times more than therapeutic dose (112.5mg/kg). Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Not all boronic acids with a five-membered cycle induce tremor, neuronal damage and decreased dopamine.

PubMed

Pérez-Rodríguez, Maribel; García-Mendoza, Esperanza; Farfán-García, Eunice D; Das, Bhaskar C; Ciprés-Flores, Fabiola J; Trujillo-Ferrara, José G; Tamay-Cach, Feliciano; Soriano-Ursúa, Marvin A

2017-09-01

Several striatal toxins can be used to induce motor disruption. One example is MPTP (1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine), whose toxicity is accepted as a murine model of parkinsonism. Recently, 3-Thienylboronic acid (3TB) was found to produce motor disruption and biased neuronal damage to basal ganglia in mice. The aim of this study was to examine the toxic effects of four boronic acids with a close structural relationship to 3TB (all having a five-membered cycle), as well as boric acid and 3TB. These boron-containing compounds were compared to MPTP regarding brain access, morphological disruption of the CNS, and behavioral manifestations of such disruption. Data was collected through acute toxicity evaluations, motor behavior tests, necropsies, determination of neuronal survival by immunohistochemistry, Raman spectroscopic analysis of brain tissue, and HPLC measurement of dopamine in substantia nigra and striatum tissue. Each compound showed a distinct profile for motor disruption. For example, motor activity was not disrupted by boric acid, but was decreased by two boronic acids (caused by a sedative effect). 3TB, 2-Thienyl and 2-furanyl boronic acid gave rise to shaking behavior. The various manifestations generated by these compounds can be linked, in part, to different levels of dopamine (measured by HPLC) and degrees of neuronal damage in the basal ganglia and cerebellum. Clearly, motor disruption is not induced by all boronic acids with a five-membered cycle as substituent. Possible explanations are given for the diverse chemico-morphological changes and degrees of disruption of the motor system, considering the role of boron and the structure-toxicity relationship. Copyright © 2017 Elsevier B.V. All rights reserved.

Partitioning of Alkali Metal Salts and Boric Acid from Aqueous Phase into the Polyamide Active Layers of Reverse Osmosis Membranes.

PubMed

Wang, Jingbo; Kingsbury, Ryan S; Perry, Lamar A; Coronell, Orlando

2017-02-21

The partition coefficient of solutes into the polyamide active layer of reverse osmosis (RO) membranes is one of the three membrane properties (together with solute diffusion coefficient and active layer thickness) that determine solute permeation. However, no well-established method exists to measure solute partition coefficients into polyamide active layers. Further, the few studies that measured partition coefficients for inorganic salts report values significantly higher than one (∼3-8), which is contrary to expectations from Donnan theory and the observed high rejection of salts. As such, we developed a benchtop method to determine solute partition coefficients into the polyamide active layers of RO membranes. The method uses a quartz crystal microbalance (QCM) to measure the change in the mass of the active layer caused by the uptake of the partitioned solutes. The method was evaluated using several inorganic salts (alkali metal salts of chloride) and a weak acid of common concern in water desalination (boric acid). All partition coefficients were found to be lower than 1, in general agreement with expectations from Donnan theory. Results reported in this study advance the fundamental understanding of contaminant transport through RO membranes, and can be used in future studies to decouple the contributions of contaminant partitioning and diffusion to contaminant permeation.

Performance Test on Polymer Waste Form - 12137

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Se Yup

Polymer solidification was attempted to produce stable waste form for the boric acid concentrates and the dewatered spent resins. The polymer mixture was directly injected into the mold or drum which was packed with the boric acid concentrates and the dewatered spent resins, respectively. The waste form was produced by entirely curing the polymer mixture. A series of performance tests was conducted including compressive strength test, water immersion test, leach test, thermal stability test, irradiation stability test and biodegradation stability test for the polymer waste forms. From the results of the performance tests for the polymer waste forms, it ismore » believed that the polymer waste form is very stable and can satisfy the acceptance criteria for permanent disposal. At present, performance tests with full scale polymer waste forms are being carried out in order to obtain qualification certificate by the regulatory institute in Korea. Polymer waste forms were prepared with the surrogate of boric acid concentrates and the surrogate of spent ion exchange resins respectively. Waste forms were also made in lab scale and in full scale. Lab. scale waste forms were directly subjected to a series of the performance tests. In the case of full scale waste form, the test specimens for the performance test were taken from a part of waste form by coring. A series of performance tests was conducted including compressive strength test, thermal stability test, irradiation stability test and biodegradation stability test, water immersion test, leach test, and free standing water for the polymer waste forms. In addition, a fire resistance test was performed on the waste forms by the requirement of the regulatory institute in Korea. Every polymer waste forms containing the boric acid concentrates and the spent ion exchange resins had exhibited excellent structural integrity of more than 27.58 MPa (4,000 psi) of compressive strength. On thermal stability testing, biodegradation testing and water immersion testing, no degradation was observed in the waste forms. Also, by measuring the compressive strength after these tests, it was confirmed that the structural integrity was still retained. A leach test was performed by using non radioactive cobalt, cesium and strontium. The leaching of cobalt, cesium and strontium from the polymer waste forms was very low. Also, the polymer waste forms were found to possess adequate fire resistance. From the results of the performance tests, it is believed that the polymer waste form is very stable and can satisfy the acceptance criteria for permanent disposal. At present, Performance tests with full scale polymer waste forms are on-going in order to obtain qualification certificate by the regulatory institute in Korea. (authors)« less

Comparison of synthetic food-based lures and liquid protein baits for capture of Anastrepha suspensa (Diptera: Tephritidae) adults

USDA-ARS?s Scientific Manuscript database

Field tests that were conducted in south Florida to compare capture of the Caribbean fruit fly, Anastrepha suspensa (Loew), in Multilure traps baited with liquid protein baits torula yeast/borax or NuLure/borax, or with food-based synthetic lures including two component (ammonium acetate, putrescine...

Efficacy of copper borax preservative against wood decay

Treesearch

William Abbott; Bessie Woodward; Michael West

2001-01-01

In this study, a wood preservative containing active ingredients of 43.5% borax and 3.1% copper hydroxide was evaluated in soil-block tests in accordance with AWPA E10. Results suggested thatthe copper hydroxide was not contributing to fungal toxicity at preservative threshold levels. Thresholds determined for this preservative were very close to those previously...

Cleaning of uranium vs machine coolant formulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cristy, S.S.; Byrd, V.R.; Simandl, R.F.

1984-10-01

This study compares methods for cleaning uranium chips and the residues left on chips from alternate machine coolants based on propylene glycol-water mixtures with either borax, ammonium tetraborate, or triethanolamine tetraborate added as a nuclear poison. Residues left on uranium surfaces machined with perchloroethylene-mineral oil coolant and on surfaces machined with the borax-containing alternate coolant were also compared. In comparing machined surfaces, greater chlorine contamination was found on the surface of the perchloroethylene-mineral oil machined surfaces, but slightly greater oxidation was found on the surfaces machined with the alternate borax-containing coolant. Overall, the differences were small and a change tomore » the alternate coolant does not appear to constitute a significant threat to the integrity of machined uranium parts.« less

Reentrant behaviour in polyvinyl alcohol-borax hydrogels

NASA Astrophysics Data System (ADS)

Lawrence, Mathias B.; Desa, J. A. E.; Aswal, V. K.

2018-01-01

Polyvinyl alcohol (PVA) hydrogels, cross-linked with varying concentrations of borax, were studied with small angle neutron scattering (SANS), x-ray diffraction (XRD) and differential thermal analysis (DTA). The SANS data satisfy the Ornstein-Zernike approximation. The hydrogels are modelled as PVA chains bound by borate cross-links. Water occupies the spaces within the three-dimensional hydrogel network. The mesh size ξ indicates reentrant behaviour i.e. at first, ξ increases and later decreases as a function of borax concentration. The behaviour is explained on the basis of the balance between the charged di-diol cross-links and the shielding by free ions in the solvent. XRD and DTA show the molecular size of water in the solvent and the glass transition temperature commensurate with reentrant behaviour.

In Situ Immobilization of Heavy Metals in Apatite Mineral Formulations

DTIC Science & Technology

1995-04-01

Free CaO. :..-..• : .."■• .■■•• •••••• -To £??£ test Chloride....;.. •: •:...... ■.;.;... ^0010>6 Sulfate , • • • :.................. ^0.02/o...34 Dehydration with IICIO, in presence of boric acid . . Molyhdnvanadophojphate jpectropholomelric method. Ilijlillalion - tilrau’on with itandard thorium...Carolina Natural Phosphate Texasgulf 30% PzOs ~ For Use As A Fertilizer In Acid Soil NCNP is a natural source of Phosphorus and Calcium derived from

Collaborative study of the determination of boric acid in caviar by emission spectroscopy.

PubMed

Franco, V; Holak, W

1975-03-01

Caviar samples were spiked at the 0.1 and 0.2% levels and digested with nitric acid in a closed Teflon-lined digestion vessel to prevent volatility losses. The boron was complexed with 2-ethyl-1,3-hexanediol and extracted into methylisobulty ketone. The emission of the boron oxide band was measured in a nitrous oxidehydrogen flame. The mean recoveries at the 0.1 and 0.2% levels for 6 collaborators were 95.7 and 97.1%, respectively.

Fire-retardant-treated strandboard : properties and fire performance

Treesearch

Jerrold Winandy; Qingwen Wang; Robert H. White

2008-01-01

This study evaluated a series of single-layer, randomly oriented strandboard panels made with one resin type, a single resin loading level, and four fire-retardant-treatment levels. The fire retardant (FR) evaluated was a pH-buffered combination of boric acid and organic phosphate. Siberian larch strands were separated into five batches. One batch of strands served as...

Running DNA Mini-Gels in 20 Minutes or Less Using Sodium Boric Acid Buffer

ERIC Educational Resources Information Center

Jenkins, Kristin P.; Bielec, Barbara

2006-01-01

Providing a biotechnology experience for students can be challenging on several levels, and time is a real constraint for many experiments. Many DNA based methods require a gel electrophoresis step, and although some biotechnology procedures have convenient break points, gel electrophoresis does not. In addition to the time required for loading…

THE ACCURATE DETERMINATION OF MICROGRAM AMOUNTS OF BORON IN ALUMINUM AND ALUMINUM-URANIUM ALLOYS BY THE METHYL BORATE-CURCUMIN-OXALIC ACID METHOD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crocker, I.H.

1958-10-01

A method was developed for the deternninntion of boron in aluminum and aluminum--uranium alloys in which the boron concentration is 30 ppm or more. Boron is separated by distillation as methyl borate from a hydrochloric acid solution of the alloy and is determined spectrophotometrically by the boric acid-- curcumin-oxalic acid color reaction. A precision of plus or minus 2% is attain able when the determination is penformed with the utmost care. The accuracy is such that no bias need be given when a calibration curve is used. (auth)

Ground-contact durability of wood treated with borax-copper preservative

Treesearch

Stan T. Lebow; Bessie Woodward; Patricia K. Lebow

2007-01-01

This study evaluated the ability of a borax-copper(BC) preservative to protect wood exposed in ground contact. Southern pine sapwood stakes were pressure-treated with 0.9%, 1.4%, 2.3%, and 4.7% BC solution concentrations and placed into the ground at test sites near Mississippi, or Madison, Wisconsin. Untreated stakes and stakes treated with 1% chromated copper...

Analysis of tincal ore waste by energy dispersive X-ray fluorescence (EDXRF) Technique

NASA Astrophysics Data System (ADS)

Kalfa, Orhan Murat; Üstündağ, Zafer; Özkırım, Ilknur; Kagan Kadıoğlu, Yusuf

2007-01-01

Etibank Borax Plant is located in Kırka-Eskişehir, Turkey. The borax waste from this plant was analyzed by means of energy dispersive X-ray fluorescence (EDXRF). The standard addition method was used for the determination of the concentration of Al, Fe, Zn, Sn, and Ba. The results are presented and discussed in this paper.

Complete Genome Sequence of Alkaliphilus metalliredigens QYMF, an Alkaliphilic and Metal-Reducing Bacterium Isolated from Borax-contaminated Leachate Ponds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, C.; Copeland, A.; Lucas, Susan

Alkaliphilus metalliredigens QYMF is an anaerobic, alkaliphilic, and metal-reducing bacterium associated with phylum Firmicutes. QYMF was isolated from alkaline borax leachate ponds. The genome sequence will help elucidate the role of metal-reducing microorganisms under alkaline environments, a capability that is not commonly observed in metal respiring-microorganisms.

Complete Genome Sequence of Alkaliphilus metalliredigens QYMF, an Alkaliphilic and Metal-Reducing Bacterium Isolated from Borax-contaminated Leachate Ponds

DOE PAGES

Hwang, C.; Copeland, A.; Lucas, Susan; ...

2016-11-03

Alkaliphilus metalliredigens QYMF is an anaerobic, alkaliphilic, and metal-reducing bacterium associated with phylum Firmicutes. QYMF was isolated from alkaline borax leachate ponds. The genome sequence will help elucidate the role of metal-reducing microorganisms under alkaline environments, a capability that is not commonly observed in metal respiring-microorganisms.

Mercury Pollution from Small-Scale Gold Mining Can Be Stopped by Implementing the Gravity-Borax Method--A Two-Year Follow-Up Study from Two Mining Communities in the Philippines.

PubMed

Køster-Rasmussen, Rasmus; Westergaard, Maria L; Brasholt, Marie; Gutierrez, Richard; Jørs, Erik; Thomsen, Jane F

2016-02-01

Mercury is used globally to extract gold in artisanal and small-scale gold mining. The mercury-free gravity-borax method for gold extraction was introduced in two mining communities using mercury in the provinces Kalinga and Camarines Norte. This article describes project activities and quantitative changes in mercury consumption and analyzes the implementation with diffusion of innovations theory. Activities included miner-to-miner training; seminars for health-care workers, school teachers, and children; and involvement of community leaders. Baseline (2011) and follow-up (2013) data were gathered on mining practices and knowledge about mercury toxicology. Most miners in Kalinga converted to the gravity-borax method, whereas only a few did so in Camarines Norte. Differences in the nature of the social systems impacted the success of the implementation, and involvement of the tribal organization facilitated the shift in Kalinga. In conclusion, the gravity-borax method is a doable alternative to mercury use in artisanal and small-scale gold mining, but support from the civil society is needed. © The Author(s) 2016.

Influence wt.% of SiC and borax on the mechanical properties of AlSi-Mg-TiB-SiC composite by the method of semi solid stir casting

NASA Astrophysics Data System (ADS)

Bhiftime, E. I.; Guterres, Natalino F. D. S.; Haryono, M. B.; Sulardjaka, Nugroho, Sri

2017-04-01

SiC particle reinforced metal matrix composites (MMCs) with solid semi stir casting method is becoming popular in recent application (automotive, aerospace). Stirring the semi solid condition is proven to enhance the bond between matrix and reinforcement. The purpose of this study is to investigate the effect of the SiC wt.% and the addition of borax on mechanical properties of composite AlSi-Mg-TiB-SiC and AlSi-Mg-TiB-SiC/Borax. Specimens was tested focusing on the density, porosity, tensile test, impact test microstructure and SEM. AlSi is used as a matrix reinforced by SiC with percentage variations (10, 15, 20 wt.%). Giving wt.% Borax which is the ratio of 1: 4 between wt.% SiC. The addition of 1.5% of TiB gives grain refinement. The use of semi-solid stir casting method is able to increase the absorption of SiC particles into a matrix AlSi evenly. The improved composite presented here can be used as a guideline to make a new composite.

Studies of quaternary saline lakes-I. Hydrogen isotope fractionation in saline minerals

USGS Publications Warehouse

Matsuo, S.; Friedman, I.; Smith, G.I.

1972-01-01

Borax, gaylussite, nahcolite and trona were synthesized in aqueous solution at temperatures ranging from 8?? to 35??C. Except for borax, deuterium was always depleted in these hydrated minerals relative to the solutions from which they were crystallized. In borax, no significant fractionation was found. The fractionation factor of D H for the trona-water system exhibited a marked temperature dependence. By combining the deuterium contents of trona and the solution from which trona was crystallized, the following thermometer scale was obtained: In ( D H) trona ( D H)water = 1.420 ?? 104 T2 + 23.56 T (1). An attempt to establish a geothermometer based on C13 C12 fractionation between carbonate minerals and carbonate ions in aqueous solution was not successful. ?? 1972.

Assessment of the chemical changes induced in human melanoma cells by boric acid treatment using infrared imaging.

PubMed

Acerbo, Alvin S; Miller, Lisa M

2009-08-01

Boron is found in everyday foods and drinking water in trace quantities. Boron exists as boric acid (BA) within plants and animals, where low levels have been linked to cancer incidence. However, this correlation is not well characterized. In this study, we examined the chemical and morphological effects of BA on human skin melanoma cells (SK-MEL28) using Fourier Transform InfraRed Imaging (FTIRI) with a Focal Plane Array (FPA) detector. Cells were grown under concentrations of BA ranging from 0 to 50 mM. Cell viability was determined after 1, 2, 3, 5, 7 and 10 days using trypan blue staining. With FTIRI, images of approximately twenty cells per time point per condition were collected. Principal components analysis (PCA) was used to evaluate changes in cell composition, with particular focus on the lipid, protein, and nucleic acid spectral components. Results from trypan blue staining revealed decreased cell viability as BA concentration increased. FTIRI data indicated that the protein and lipid contents (as indicated by the lipid/protein ratio) did not undergo substantial changes due to BA treatment. In contrast, the nucleic acid/protein ratio significantly decreased with BA treatment. PCA results showed an increase in beta-sheet protein at higher concentrations of BA (12.5, 25, and 50 mM). Together, these results suggest that high concentrations of BA have an anti-proliferative effect and show signs consistent with apoptosis.

Synergy and Diffusion with a Borax-Copper Hydroxide Groundline Preservative: 20 Year Update

Treesearch

Stan Lebow; Bessie Woodward; Bill Abbott; Mike West

2014-01-01

A groundline remedial treatment containing 3.1% copper hydroxide (2% elemental copper) and 40% sodium tetraborate decahydrate (borax) was applied to unseasoned pine posts prior to placement in a test site in southern Mississippi. The soundness of the posts was periodically evaluated using a push test. After 3.5, 6.5, 10, 15 and 20 years, sections were taken from two...

Complete Genome Sequence of Alkaliphilus metalliredigens Strain QYMF, an Alkaliphilic and Metal-Reducing Bacterium Isolated from Borax-Contaminated Leachate Ponds

PubMed Central

Copeland, A.; Lucas, S.; Lapidus, A.; Barry, K.; Detter, J. C.; Glavina del Rio, T.; Hammon, N.; Israni, S.; Dalin, E.; Tice, H.; Pitluck, S.; Chertkov, O.; Brettin, T.; Bruce, D.; Han, C.; Schmutz, J.; Larimer, F.; Land, M. L.; Hauser, L.; Kyrpides, N.; Mikhailova, N.; Ye, Q.; Zhou, J.; Richardson, P.; Fields, M. W.

2016-01-01

Alkaliphilus metalliredigens strain QYMF is an anaerobic, alkaliphilic, and metal-reducing bacterium associated with phylum Firmicutes. QYMF was isolated from alkaline borax leachate ponds. The genome sequence will help elucidate the role of metal-reducing microorganisms under alkaline environments, a capability that is not commonly observed in metal respiring-microorganisms. PMID:27811105

The levels of boron-uptake proteins in roots are correlated with tolerance to boron stress in barley

USDA-ARS?s Scientific Manuscript database

Boron (B) is an essential micronutrient required for plant growth and development. Recently, two major B-uptake proteins, BOR1 and NIP5;1 have been identified and partially characterized. BOR1 is a high-affinity B transporter involved in xylem loading in roots, and NIP5;1 acts is a major boric-acid ...

Physical and mechanical properties and fire, decay, and termite resistance of treated oriented strandboard

Treesearch

Nadir Ayrilmis; S Nami Kartal; Theodore L. Laufenberg; Jerrold E. Winandy; Robert H. White

2005-01-01

This study evaluated the effects of a number of chemicals on the physical and mechanical properties and fire, decay, and termite resistance of oriented strandboard (OSB) panels. Disodium octaborate tetrahydrate (DOT), boric acid (BA), melamine phosphate (MP), and a BA/DOT mixture were sprayed onto the furnish at varying concentrations. The panels were tested for...

Synthesis and evaluation of borates derived from boric acid for fire and decay protections

Treesearch

George Chen

1999-01-01

The degradation of wood by decay, fire and UV constitutes the three major losses of wood products in use. Commercial wood preservatives including chromated copper arsenate(CCA) and pentachlorophenol(penta) can only protect wood from decay. Dual protections of wood against decay and fire or decay and UV if acheivable are more desirable. Many phosphorus and boron...

Utilization of Negative Ion ESI-MS and Tandem Mass Spectrometry to Detect and Confirm the NADH-Boric Acid Complex

ERIC Educational Resources Information Center

Kim, Danny H.; Eckhert, Curtis D.; Faull, Kym F.

2011-01-01

Mass spectrometry (MS) is a powerful analytical technique that is now widely used in the chemical, physical, engineering, and life sciences, with rapidly growing applications in many areas including clinical, forensic, pharmaceutical, and environmental fields. The increase in use of MS in both academic and industrial settings for research and…

Therapeutic efficacy for hepatocellular carcinoma by boric acid-mediated boron neutron capture therapy in a rat model.

PubMed

Lin, Sy-Yu; Lin, Chen-Jou; Liao, Jiunn-Wang; Peir, Jinn-Jer; Chen, Wei-Lin; Chi, Chin-Wen; Lin, Yung-Chang; Liu, Yu-Ming; Chou, Fong-In

2013-11-01

Hepatocellular carcinoma (HCC) is a common malignant tumor with poor prognosis. Boron neutron capture therapy (BNCT) may provide an alternative therapy for HCC. This study investigated the therapeutic efficacy of boric acid (BA)-mediated BNCT for HCC in a rat model. The pharmacokinetic and biodistribution of BA in N1S1 tumor-bearing rats were analyzed. Rats were injected with 25 mg B/kg body weight via tail veins before neutron irradiation at the Tsing Hua Open-pool Reactor, and the efficacy of BNCT was evaluated from the tumor size, tumor blood flow, and biochemical analyses. HCC-bearing rats administered BNCT showed reductions in tumor size on ultrasound imaging, as well as an obvious reduction in the distribution of tumor blood flow. The lesion located in livers had disappeared on the 80th day after BNCT; a recovery of values to normal levels was also recorded. BA-mediated BNCT is a promising alternative for liver cancer therapy since the present study demonstrated the feasibility of curing a liver tumor and restoring liver function in rats. Efforts are underway to investigate the histopathological features and the detailed mechanisms of BA-mediated BNCT.

Effect of Silica Nanoparticles on the Photoluminescence Properties of BCNO Phosphor

NASA Astrophysics Data System (ADS)

Nuryadin, Bebeh W.; Faryuni, Irfana Diah; Iskandar, Ferry; Abdullah, Mikrajuddin; Khairurrijal, Khairurrijal

2011-12-01

Effect of additional silica nanoparticles on the photoluminescence (PL) performance of boron carbon oxy-nitride (BCNO) phosphor was investigated. As a precursor, boric acid and urea were used as boron and nitrogen sources, respectively. The carbon sources was polyethylene glycol (PEG) with average molecule weight 20000 g/mol.. Precursor solutions were prepared by mixing these raw materials in pure water, followed by stirring to achieve homogeneous solutions. In this precursor, silica nanoparticles were added at various mass ratio from 0 to 7 %wt in the solution. The precursors were then heated at 750 °C for 60 min in a ceramic crucible under atmospheric pressure. The photoluminescence (PL) spectrum that characterized by spectrophotometer showed a single, distinct, and broad emission band varied from blue to near red color, depend on the PEG, boric acid and urea ratio in the precursor. The addition of silica nanoparticles caused the increasing of PL intensity as well as the shifting of peak wavelength of PL spectrum. The peak shifting of PL was affected by the concentration of silica nanoparticles that added into the precursor. We believe that the BCNO-silica composite phosphor becomes a promising material for the phosphor conversion-based white light-emitting diodes.

Control of Linepithema micans (Hymenoptera: Formicidae) and Eurhizococcus brasiliensis (Hemiptera: Margarodidae) in Vineyards Using Toxic Baits.

PubMed

Nondillo, Aline; Andzeiewski, Simone; Bello Fialho, Flávio; Bueno, Odair Correa; Botton, Marcos

2016-08-01

Linepithema micans (Forel) (Hymenoptera: Formicidae) is the main ant species responsible for dispersal of Eurhizococcus brasiliensis (Wille) (Hemiptera: Margarodidae), a root scale that damages grapevines in southern Brazil. The effects of different formulations of toxic baits based on boric acid and hydramethylnon to control L. micans and E. brasiliensis were evaluated. Toxic baits with boric acid (1.0%) mixed in different concentrations of inverted sugar (20%, 30%, and 40%), and hydramethylnon, mixed with sardines (paste), cassava flour and peanut, brown sugar (sucrose), or sardine oil-based gel, were evaluated in a greenhouse and in the field. In the greenhouse experiment, the number of foraging ants was significantly reduced in the pots where the hydramethylnon in sardine paste (Solid S), sardine oil-brown sugar-based gel (GEL SAM), and peanut oil-brown-sugar gel (GEL AM) formulations were applied. The GEL SAM toxic bait effectively reduced the infestation of L. micans, and could be used for indirect control of E. brasiliensis on young grapevines. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Human environmental and occupational exposures to boric acid: reconciliation with experimental reproductive toxicity data.

PubMed

Bolt, Hermann M; Başaran, Nurşen; Duydu, Yalçın

2012-01-01

The reproductive toxicity of boric acid and borates is a matter of current regulatory concern. Based on experimental studies in rats, no-observed-adverse-effect levels (NOAELs) were found to be 17.5 mg boron (B)/kg body weight (b.w.) for male fertility and 9.6 mg B/kg b.w. for developmental toxicity. Recently, occupational human field studies in highly exposed cohorts were reported from China and Turkey, with both studies showing negative results regarding male reproduction. A comparison of the conditions of these studies with the experimental NOAEL conditions are based on reported B blood levels, which is clearly superior to a scaling according to estimated B exposures. A comparison of estimated daily B exposure levels and measured B blood levels confirms the preference of biomonitoring data for a comparison of human field studies. In general, it appears that high environmental exposures to B are lower than possible high occupational exposures. The comparison reveals no contradiction between human and experimental reproductive toxicity data. It clearly appears that human B exposures, even in the highest exposed cohorts, are too low to reach the blood (and target tissue) concentrations that would be required to exert adverse effects on reproductive functions.

Comparison of an Ultrasonic Phased Array Evaluation with Destructive Analysis of a Documented Leak Path in a Nozzle Removed from Service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cinson, Anthony D.; Crawford, Susan L.; MacFarlan, Paul J.

2012-09-24

Non-destructive and destructive testing methods were employed to evaluate a documented boric acid leakage path through an Alloy 600 control rod drive mechanism (CRDM) penetration from the North Anna Unit 2 reactor pressure vessel head that was removed from service in 2002. A previous ultrasonic in-service-inspection (ISI) conducted by industry prior to the head removal, identified a probable leakage path in Nozzle 63 located in the interference fit between the penetration tube and the vessel head. In this current examination, Nozzle 63 was examined using phased array (PA) ultrasonic testing with a 5.0-MHz, eight-element annular array; immersion data were acquiredmore » from the nozzle inner diameter (ID) surface. A variety of focal laws were employed to evaluate the signal responses from the interference fit region. These responses were compared to responses obtained from a mockup specimen that was used to determine detection limits and characterization capabilities for wastage and boric acid presence in the interference fit region. Nozzle 63 was destructively examined after the completion of the ultrasonic nondestructive evaluation (NDE) to visually assess the leak paths. These destructive and nondestructive results compared favorably« less

Controlling the optical properties of polyaniline doped by boric acid particles by changing their doping agent and initiator concentration

NASA Astrophysics Data System (ADS)

Cabuk, Mehmet; Gündüz, Bayram

2017-12-01

In this study, polyaniline doped by boric acid (PAni:BA) conducting polymers were chemically synthesized by oxidative polymerization method using (NH4)2S208 (APS) as initiator. Pani:BA conducting polymers were synthesized by using two different APS/aniline molar ratios as 1:1 and 2:1. Their results were compared with PAni doped by HCl (PAni) conducting polymer. Structural properties of the PAni, PAni:BA (1:1) and PAni:BA (2:1) conducting polymers were characterized by using FTIR, SEM, TGA, particle size and apparent density measurements. Effects of doping agents and initiator concentrations on optical properties were investigated in detail. The optoelectronic parameters such as absorption band edge, molar extinction coefficient, direct allowed band gap, refractive index, optical conductance and electrical conductance of the PAni, PAni:BA (1:1) and PAni:BA (2:1) were determined. The absorption band edge and direct allowed band gap of PAni were decreased with doping BA and increasing APS ratio. Also, the refractive index values of the materials were calculated from experimental results and compared with obtained results from Moss, Ravindra, Herve-Vandamme, Reddy and Kumar-Singh relations.

Selection of fluxing agent for coal ash and investigation of fusion mechanism: a first-principles study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jie Li; Mei-Fang Du; Zhong-Xiao Zhang

2009-01-15

An approach based on the ab initio quantum chemical modeling (CASTEP, generalized gradient approximation (GGA), and density functional theory (DFT)) was first employed to guide the selection of the appropriate fluxing agent to reduce the coal ash melting temperature. Two kinds of typical Chinese coal ash A and B with a high-melting temperature were chosen as the investigated subjects. Result of the calculation shows that mullite mineral, which is the main component of coal ash, is easier to combine with an electron acceptor than with an electron donor. Because the cations of borax (Na{sub 2}B{sub 4}O{sub 7}10H{sub 2}O) and limestonemore » can act as electron acceptors, borax and limestone were selected as the fluxing agents in our experiment. Results of the experiment show that the melting temperatures of coal ash A and B are both decreased by borax and limestone, respectively. Moreover, borax has a better fluxing effect than limestone under the same conditions. The further numerical study on the coal ash fusing mechanism indicates that the Na{sup +} and Ca{sup 2+} cations, as acceptors, can enter into the crystal lattice of mullite mainly through O(7) and O(8) and then cause the Al(6)-O(8) and Al(5)-O(7) bonds to rupture in the (AlO{sub 6})-octahedron. From this, mullite is forced to transform to feldspar and corundum minerals that have a low binding energy. Because of the phase change of minerals in the coal ash, the coal ash melting temperature is decreased by adding borax and limestone. 27 refs., 8 figs., 3 tabs.« less

Jack bean urease: the effect of active-site binding inhibitors on the reactivity of enzyme thiol groups.

PubMed

Krajewska, Barbara; Zaborska, Wiesława

2007-10-01

In view of the complexity of the role of the active site flap cysteine in the urease catalysis, in this work we studied how the presence of typical active-site binding inhibitors of urease, phenylphosphorodiamidate (PPD), acetohydroxamic acid (AHA), boric acid and fluoride, affects the reactivity of enzyme thiol groups, the active site flap thiol in particular. For that the inhibitor-urease complexes were prepared with excess inhibitors and had their thiol groups titrated with DTNB. The effects observed were analyzed in terms of the structures of the inhibitor-urease complexes reported in the literature. We found that the effectiveness in preventing the active site cysteine from the modification by disulfides, varied among the inhibitors studied, even though they all bind to the active site. The variations were accounted for by different extents of geometrical distortion in the active site that the inhibitors introduced upon binding, leaving the flap either open in AHA-, boric acid- and fluoride-inhibited urease, like in the native enzyme or closed in PPD-inhibited urease. Among the inhibitors, only PPD was found to be able to thoroughly protect the flap cysteines from the further reaction with disulfides, this apparently resulting from the closed conformation of the flap. Accordingly, in practical terms PPD may be regarded as the most suitable inhibitor for active-site protection experiments in inhibition studies of urease.

Silk flame retardant finish by ternary silica sol containing boron and nitrogen

NASA Astrophysics Data System (ADS)

Zhang, Qiang-hua; Chen, Guo-qiang; Xing, Tie-ling

2017-11-01

A ternary flame retardant sol system containing Si, B and N was prepared via sol gel method using tetraethoxysilane (TEOS) as a precursor, boric acid (H3BO3) and urea (CO(NH2)2) as flame retardant additives and then applied to silk fabric flame retardant finish. The FT-IR and SEM results showed that the nitrogen-boron-silica ternary sol was successfully prepared and entrapped onto the surface of silk fibers. The limiting oxygen index (LOI) test indicated that the silk fabric treated with 24% boric acid and 6% urea (relative to the TEOS) doped ternary silica sol system performed excellent flame retardancy with the LOI value of 34.6%. Furthermore, in order to endow silk fabric with durable flame retardancy, the silk fabric was pretreated with 1,2,3,4-butanetetracarboxylic acid (BTCA) before the ternary sol system treatment. The BTCA pretreat ment applied to silk could effectively promote the washing durability of the ternary sol, and the LOI value of the treated sample after 10 times washing could still maintain at 30.8% compared with that of 31.0% before washing. Thermo gravimetric (TG), micro calorimeter combustion (MCC) and smoke density test results demonstrated that the thermal stability, heat release and smoke suppression of the nitrogen-boron-silica ternary system decreased somewhat compared with the boron-silica binary flame retardant system.

Direct monitoring by carbon-13 nuclear magnetic resonance spectroscopy of the metabolism and metabolic rate of 13C-labeled compounds in vivo.

PubMed

Iida, K; Hidoh, O; Fukami, J; Kajiwara, M

1991-01-01

Carbon-13 nuclear magnetic resonance spectroscopy has been used to observe the transformations of [1-13C]-D-glucose to [1,1'-13C2]-D-trehalose, and [3-13C]-L-alanine to [2-13C]-L-glutamic acid in the living body of Gryllodes sigillatus. [3-13C]-D-Alanine was not metabolized. The metabolic rate of [1-13C]-D-glucose was found to be altered by prior injection of boric acid.

Quantitative determination of alginic acid in pharmaceutical formulations using capillary electrophoresis.

PubMed

Moore, Douglas E; Miao, William G; Benikos, Con

2004-01-27

A capillary electrophoresis (CE) method has been developed and validated for the quantitative determination of alginic acid, which is used as a rafting agent in complex antacid formulations. The method involves a preliminary separation of the alginic acid from the formulation by washing the sample matrix with methanol, diluted HCl and water. This is followed by electrophoresis within a fused silica capillary using borate/boric acid buffer as the electrolyte, and the quantification is performed by a UV detector monitoring at 200 nm, where the intrinsic absorption of alginic acid is measured. An assay precision of better than 3% was achieved in intra- and interday determinations. No interference was found from the matrix of the antacid formulations.

Nanoparticles as strengthening agents in polymer systems

NASA Astrophysics Data System (ADS)

Shahid, Naureen

2005-11-01

Carboxylate-substituted alumina nanoparticles are produced solvent free using mechanical shear. The general nature of this method has been demonstrated for L-lysine-, stearate, and p-hydroxybenzoate-derived materials. The reaction rate and particle size is controlled by a combination of temperature and shear rate. The nanoparticles are spectroscopically equivalent to those reported from aqueous syntheses, however, the average particle size can be decreased and the particle size distribution narrowed depending on the reaction conditions. Lysine and p-hydroxybenzoato alumoxanes have been introduced in carbon fiber reinforced epoxide resin composites. Different preparation conditions have been studied to obtain composite with enhanced performances that are ideal for the motor sports and aerospace industries. A new composite material has been fabricated utilizing surface-modified carboxylate alumoxane nanoparticles and the biodegradable polymer poly(propylene fumarate)/poly(propylene fumarate)-diacrylate (PPF/PPF-DA). For this study, composites were prepared using various functional groups including: a surfactant alumoxane to enhance nanoparticle dispersion into the polymer; an activated-alumoxane to enhance nanoparticle interaction with the polymer matrix; a mixed alumoxane containing both activated and surfactant groups. Nanocomposites prepared with all types of alumoxane, as well as blank polymer resin and unmodified boehmite, underwent mechanical testing and were characterized by SEM and microprobe analysis. A nanocomposite composed of mixed alumoxane nanoparticles dispersed in PPF/PPF-DA exhibited increased flexural modulus compared to polymer resin alone, and a significant enhancement over both the activated and surfacted alumoxanes. Boric acid is used as the cross-linking agent in oil well drilling industry even though the efficacy of the borate ion, [B(OH)4]- , as a cross-linking agent is poor. The reaction product of boric acid and the polysaccharide guaran (the major component of guar gum) has been investigated by 11B NMR spectroscopy. By comparison with the 11B NMR of boric acid and phenyl boronic acid complexes of 1,2-diols [HOCMe2CMe2OH, cis-C6H 10(OH)2, trans-C6H10(OH) 2, o-C6H4(OH)2], 1,3-diols (neol-H2), monosaccharides (L-fucose, mannose and galactose) and disaccharides (celloboise and sucrose) it is found that the guaran polymer is cross-linked via a borate complex of two 1,2-diols both forming chelate 5-membered ring cycles, this contrasts with previous proposals. (Abstract shortened by UMI.)

Boric acid flux synthesis, structure and magnetic property of MB₁₂O₁₄(OH)₁₀ (M=Mn, Fe, Zn)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dingfeng; Cong, Rihong; Gao, Wenliang, E-mail: gaowl@cqu.edu.cn

2013-05-01

Three new borates MB₁₂O₁₄(OH)₁₀ (M=Mn, Fe, Zn) have been synthesized by boric acid flux methods, which are isotypic to NiB₁₂O₁₄(OH)₁₀. Single-crystal XRD was performed to determine the crystal structures in detail. They all crystallize in the monoclinic space group P2₁/c. The size of MO{sub 6} (M=Mg, Mn, Fe, Co, Ni, Zn) octahedron shows a good agreement with the Shannon effective ionic radii of M²⁺. Magnetic measurements indicate MnB₁₂O₁₄(OH)₁₀ is antiferromagnetic without a long-range ordering down to 2 K. The values of its magnetic superexchange constants were evaluated by DFT calculations, which explain the observed magnetic behavior. The UV–vis diffuse reflectancemore » spectrum of ZnB₁₂O₁₄(OH)₁₀ suggests a band gap ~4.6 eV. DFT calculations indicate it has a direct band gap 4.9 eV. The optical band gap is contributed by charge transfers from the occupied O 2p to the unoccupied Zn 4s states. - Graphical abstract: Experimental and theoretical studies indicate MnB₁₂O₁₄(OH)₁₀ is antiferromagnetic without a long-range ordering. DFT calculations show ZnB₁₂O₁₄(OH)₁₀ has a direct band gap of 4.9 eV. Highlights: • MB₁₂O₁₄(OH)₁₀ (M=Mn, Fe, Zn) are synthesized by two-step boric acid flux method. • Single-crystal XRD was performed to determine the crystal structures in detail. • Size of MO₆ (M=Mg, Mn, Fe, Co, Ni, Zn) agrees with the effective ionic radii. • MnB₁₂O₁₄(OH)₁₀ is antiferromagnetic without a long-range ordering down to 2 K. • DFT calculations indicate ZnB₁₂O₁₄(OH)₁₀ has a direct band gap 4.9 eV.« less

GEMAS: prediction of solid-solution phase partitioning coefficients (Kd) for oxoanions and boric acid in soils using mid-infrared diffuse reflectance spectroscopy.

PubMed

Janik, Leslie J; Forrester, Sean T; Soriano-Disla, José M; Kirby, Jason K; McLaughlin, Michael J; Reimann, Clemens

2015-02-01

The authors' aim was to develop rapid and inexpensive regression models for the prediction of partitioning coefficients (Kd), defined as the ratio of the total or surface-bound metal/metalloid concentration of the solid phase to the total concentration in the solution phase. Values of Kd were measured for boric acid (B[OH]3(0)) and selected added soluble oxoanions: molybdate (MoO4(2-)), antimonate (Sb[OH](6-)), selenate (SeO4(2-)), tellurate (TeO4(2-)) and vanadate (VO4(3-)). Models were developed using approximately 500 spectrally representative soils of the Geochemical Mapping of Agricultural Soils of Europe (GEMAS) program. These calibration soils represented the major properties of the entire 4813 soils of the GEMAS project. Multiple linear regression (MLR) from soil properties, partial least-squares regression (PLSR) using mid-infrared diffuse reflectance Fourier-transformed (DRIFT) spectra, and models using DRIFT spectra plus analytical pH values (DRIFT + pH), were compared with predicted log K(d + 1) values. Apart from selenate (R(2)  = 0.43), the DRIFT + pH calibrations resulted in marginally better models to predict log K(d + 1) values (R(2)  = 0.62-0.79), compared with those from PSLR-DRIFT (R(2)  = 0.61-0.72) and MLR (R(2)  = 0.54-0.79). The DRIFT + pH calibrations were applied to the prediction of log K(d + 1) values in the remaining 4313 soils. An example map of predicted log K(d + 1) values for added soluble MoO4(2-) in soils across Europe is presented. The DRIFT + pH PLSR models provided a rapid and inexpensive tool to assess the risk of mobility and potential availability of boric acid and selected oxoanions in European soils. For these models to be used in the prediction of log K(d + 1) values in soils globally, additional research will be needed to determine if soil variability is accounted on the calibration. © 2014 SETAC.

Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report

PubMed Central

2016-01-01

This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician’s diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC). A patch test using the toothpaste containing sodium lauryl sulfate (SLS) was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case. PMID:27789914

Glycerin Borax Treatment of Exfoliative Cheilitis Induced by Sodium Lauryl Sulfate: a Case Report.

PubMed

Thongprasom, Kobkan

2016-06-01

This paper reports on the results of a case study of a 19-year-old female who presented to the Oral Medicine clinic with a chief complaint of scaly and peeling lips. The lesions had persisted on her lips for more than 7 years and were refractory to previous treatment. Her physician's diagnosis was contact dermatitis. We diagnosed this patient as having exfoliative cheilitis (EC). A patch test using the toothpaste containing sodium lauryl sulfate (SLS) was positive and the patient discontinued using it. Instead, she started using a toothpaste not containing SLS. One year after treating her lesions with hydrogen peroxide mouthwash 1% and glycerin borax, a gradual improvement was observed until returning to normal. Glycerin borax was safe, low cost and simple to use in treatment of refractory exfoliative cheilitis. SLS may have been a precipitating factor in EC in this case.

Validation of MCNP: SPERT-D and BORAX-V fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.; Palmer, B.

1992-11-01

This report discusses critical experiments involving SPERT-D{sup 1,2} fuel elements and BORAX-V{sup 3-8} fuel which have been modeled and calculations performed with MCNP. MCNP is a Monte Carlo based transport code. For this study continuous-energy nuclear data from the ENDF/B-V cross section library was used. The SPERT-D experiments consisted of various arrays of fuel elements moderated and reflected with either water or a uranyl nitrate solution. Some SPERT-D experiments used cadmium as a fixed neutron poison, while others were poisoned with various concentrations of boron in the moderating/reflecting solution. ne BORAX-V experiments were arrays of either boiling fuel rod assembliesmore » or superheater assemblies, both types of arrays were moderated and reflected with water. In one boiling fuel experiment, two fuel rods were replaced with borated stainless steel poison rods.« less

Validation of MCNP: SPERT-D and BORAX-V fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.; Palmer, B.

1992-11-01

This report discusses critical experiments involving SPERT-D[sup 1,2] fuel elements and BORAX-V[sup 3-8] fuel which have been modeled and calculations performed with MCNP. MCNP is a Monte Carlo based transport code. For this study continuous-energy nuclear data from the ENDF/B-V cross section library was used. The SPERT-D experiments consisted of various arrays of fuel elements moderated and reflected with either water or a uranyl nitrate solution. Some SPERT-D experiments used cadmium as a fixed neutron poison, while others were poisoned with various concentrations of boron in the moderating/reflecting solution. ne BORAX-V experiments were arrays of either boiling fuel rod assembliesmore » or superheater assemblies, both types of arrays were moderated and reflected with water. In one boiling fuel experiment, two fuel rods were replaced with borated stainless steel poison rods.« less

Final report of the decontamination and decommissioning of the BORAX-V facility turbine building

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arave, A.E.; Rodman, G.R.

1992-12-01

The Boiling Water Reactor Experiment (BORAX)-V Facility Turbine Building Decontamination and Decommissioning (D&D) Project is described in this report. The BORAX series of five National Reactor Testing Station (NRTS) reactors pioneered intensive work on boiling water reactor (BWR) experiments conducted between 1953 and 1964. Facility characterization, decision analyses, and D&D plans for the turbine building were prepared from 1979 through 1990. D&D activities of the turbine building systems were initiated in November of 1988 and completed with the demolition and backfill of the concrete foundation in March 1992. Due to the low levels of radioactivity and the absence of loosemore » contamination, the D&D activities were completed with no radiation exposure to the workers. The D&D activities were performed in a manner that no radiological health or safety hazard to the public or to personnel at the Idaho National Engineering Laboratory (INEL) remain.« less

Final report of the decontamination and decommissioning of the BORAX-V facility turbine building

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arave, A.E.; Rodman, G.R.

1992-12-01

The Boiling Water Reactor Experiment (BORAX)-V Facility Turbine Building Decontamination and Decommissioning (D D) Project is described in this report. The BORAX series of five National Reactor Testing Station (NRTS) reactors pioneered intensive work on boiling water reactor (BWR) experiments conducted between 1953 and 1964. Facility characterization, decision analyses, and D D plans for the turbine building were prepared from 1979 through 1990. D D activities of the turbine building systems were initiated in November of 1988 and completed with the demolition and backfill of the concrete foundation in March 1992. Due to the low levels of radioactivity and themore » absence of loose contamination, the D D activities were completed with no radiation exposure to the workers. The D D activities were performed in a manner that no radiological health or safety hazard to the public or to personnel at the Idaho National Engineering Laboratory (INEL) remain.« less

A dry powder stump applicator for a feller-buncher.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karsky, Richard, J.; Cram Michelle; Thistle, Harold

1998-07-11

Karsky, D., M. Cram, and H. Thistle. 1998. A dry powder borax stump applicator for a feller-buncher. Presented at the 1998 ASAE Annual International Meeting at Colorado Springs Resort, Orlando, Florida, July 11-16, 1998. Paper No. 987023. ASAE, 2950 Niles Road, St. Joseph, MI 49085-9659. Annosum root rot affects conifers throughout the Northern Hemisphere, infecting the roots and eventually killing the trees. An applicator attachment has been developed that mounts to the back of a feller-buncher saw head, that can reduce mortality from Heterobasidion annosum. The attachment applies a borax powder to a stump immediately after the tree has beenmore » cut. This document provides information on the design, development and testing of an applicator for applying dry borax on tree stumps at the time of harvesting to reduce future losses due to root rot.« less

Photonic crystal borax competitive binding carbohydrate sensing motif†

PubMed Central

Cui, Qingzhou; Muscatello, Michelle M. Ward; Asher, Sanford A.

2009-01-01

We developed a photonic crystal sensing method for diol containing species such as carbohydrates based on a poly(vinyl alcohol) (PVA) hydrogel containing an embedded crystalline colloidal array (CCA). The polymerized CCA (PCCA) diffracts visible light. We show that in the presence of borax the diffraction wavelength shifts as the concentration of glucose changes. The diffraction shifts result from the competitive binding of glucose to borate, which reduces the concentration of borate bound to the PVA diols. PMID:19381378

Investigation of the matrix effect in determining microimpurities in boron and its compounds by atomic-emission spectrometry

NASA Astrophysics Data System (ADS)

Lebedeva, R. V.; Tumanova, A. N.; Mashin, N. I.

2007-07-01

We carried out a systematic study of the influence of the main component on the change of analytical signal during atomic-emission analysis of boron compounds. Changes in the intensity of spectral lines of microimpurities as functions of their concentrations in the analytical system based on graphite powder with a variable content of boric acid and boron oxide are presented.

Inexpensive Method for Coating the Interior of Silica Growth Ampoules with Pyrolytic Boron Nitride

NASA Technical Reports Server (NTRS)

Wang, Jianbin; Regel, Liya L.; Wilcox, William R.

2003-01-01

An inexpensive method was developed for coating the interior of silica ampoules with hexagonal boron nitride. An aqueous solution of boric acid was used to coat the ampoule prior to drying in a vacuum at 200 C. This coating was converted to transparent boron nitride by heating in ammonia at 1000 C. Coated ampoules were used to achieve detached solidification of indium antimonide on earth.

Candida vaginitis during contraceptive use: the influence of methods, antifungal susceptibility and virulence patterns.

PubMed

Güzel, A B; Küçükgöz-Güleç, U; Aydin, M; Gümral, R; Kalkanci, A; Ilkit, M

2013-11-01

No consensus exists about whether contraceptives cause an increased risk of vaginitis, including vulvovaginal candidosis (VVC). We investigated 495 women (252 who used contraceptives; 243 who did not) for the presence of VVC. Antifungal susceptibility testing was performed for five antifungal agents and for boric acid, and three virulence factors were also examined. We recovered 129 (26.1%) monofungal populations from vaginal samples of women with acute VVC (AVVC, n = 18), symptomatic recurrent VVC (RVVC, n = 22) and asymptomatic RVVC (n = 28), as well as of other contraceptive users who carried Candida in their vaginas (n = 61). It is important to note that the women who had VVC used the same contraceptive methods (p > 0.05). Candida albicans was the most common species isolated (45%), followed by C. glabrata (40.3%). Most of the vaginal yeast isolates exhibited low minimum inhibitory concentration levels for the five antifungals tested. However, this was not the case for boric acid. In addition, the yeast fungi that was derived from the AVVC and RVVC patients showed higher amounts of haemolytic activity than the yeast fungi found among the controls (p < 0.05). The use of contraception does not predispose women to VVC (p > 0.05). Also, both host- and organism-related factors were required to achieve optimal clinical treatment for VVC.

Design and optimization of production parameters for boric acid crystals with the crystallization process in an MSMPR crystallizer using FBRM® and PVM® technologies

NASA Astrophysics Data System (ADS)

Kutluay, Sinan; Şahin, Ömer; Ceyhan, A. Abdullah; İzgi, M. Sait

2017-06-01

In crystallization studies, newly developed technologies, such as Focused Beam Reflectance Measurement (FBRM) and Particle Vision and Measurement (PVM) are applied for determining on-line monitoring of a representation of the Chord Length Distribution (CLD) and observe the photographs of crystals respectively; moreover recently they are widely used. Properly installed, the FBRM ensures on-line determination of the CLD, which is statistically associated to the Crystal Size Distribution (CSD). In industrial crystallization, CSD and mean crystal size as well as external habit and internal structure are important characteristics for further use of the crystals. In this paper, the effect of residence time, stirring speed, feeding rate, supersaturation level and the polyelectrolytes such as anionic polyacrylamide (APAM) and non-ionic polyacrylamide (NPAM) on the CLD as well as the shape of boric acid crystals were investigated by using the FBRM G600 and the PVM V819 probes respectively in an MSMPR (Mixed Suspension Mixed Product Removal) crystallizer. The CSD and kinetic data were determined experimentally using continuous MSMPR crystallizer running at steady state. The population density of nuclei, the nucleation rate and the growth rate were determined from the experimental population balance distribution when the steady state was reached.

Preliminary study on detection technology of the cladding weld of spent fuel storage pool

NASA Astrophysics Data System (ADS)

Qi, Pan; Cui, Hongyan; Feng, Meiming; Shao, Wenbin; Liao, Shusheng; Li, Wei

2018-04-01

As the first barrier of the Spent fuel storage pool, the steel cladding using different sizes (length×width) of 304L stainless steel with 3˜6mm thickness plate argon arc welded together which is direct contacted with boric acid water. Environmental humidity between the back of steel cladding and concrete, makes phosphate, chloride ion overflowed from the concrete that corroded on the weld zone with different mechanism. Part of the corrosion defects can penetrate leaded to leakage of boric acid water in penetration position accelerated crack propagation. In view of the above situation and combined with the actual needs of the power plant, the development of effective underwater nondestructive testing means of the weld area for periodic inspection and monitoring is necessary. A single method may lead to the missing of defects detection due to weld reinforcement unpolished. In this paper, eddy current array (ARRAY) and Alternating Current Field Measurement (ACFM) are adapted to test the limit sensitivity and resolution through by the specimens with artificial defects which make their detection abilities close to satisfy engineering requirements. The preliminary study found that Φ0.5mm through-wall hole and with 2mm length and 0.3mm width through-wall crack in the weld can be good inspected.

[Search for antimicrobial agents and their various combinations that are effective in relation to the main microfloral representatives in the burn wound].

PubMed

Kataev, S V; Brodinova, N S; Moroz, A F

1980-03-01

Activity of 10 antibiotics, 6 surface active substances, 1 antioxidant and boric acid against P. aeruginosa, E. coli, Pr. vulgaris and Staph. aureus most frequently vegetating in burn wounds was studied. It was found that gentamicin had the highest antibacterial effect on the above organisms. Polymyxin M had a pronounced antimicrobial action on P. aeruginosa and E. coli. A significant antibacterial effect with respect to Staph. aureus, E. coli and Pr. vulgaris was observed with the use of the drugs of the nitrofuran line, i.e. salaful, furagin and furacillin. These drugs were not active against P. aeruginosa. A high antimicrobial effect with respect to all of the test-microbed used was recorded with methacyl, a surface active substance. To show the synergistic effect on the microbes most frequently vegetating in burn wounds, the antibacterial action of the drug combinations was studied. The synergistic effect (16 to 100 times) was observed with the use of polymyxin M combination with mafenide, carbenicillin with gentamicin, methacide with fenozan. The microorganisms tested were resistant to boric acid. On the basis of the study the most effective drugs and their combinations were chosen for their addition to the algipores (polymer coatings) used in treatment of burns infected with the above microbes.

Boric Acid Inhibition of Trichophyton rubrum Growth and Conidia Formation.

PubMed

Schmidt, Martin

2017-12-01

Trichophyton rubrum is a common human dermatophyte that is the causative agent of 80-93% of fungal infections of the skin and nails. While dermatophyte infections in healthy people are easily treatable with over-the-counter medications, such infections pose a higher risk for patients with compromised immune function and impaired regenerative potential. The efficacy of boric acid (BA) for the treatment of vaginal yeast infections prompted an investigation of the effect of BA on growth and morphology of T. rubrum. This is of particular interest since BA facilitates wound healing, raising the possibility that treating athlete's foot with BA, either alone or in combination with other antifungal drugs, would combine the benefits of antimicrobial activity and tissue regeneration to accelerate healing of infected skin. The data presented here show that BA represses T. rubrum growth at a concentration reported to be beneficial for host tissue regeneration. Oxygen exposure increases BA toxicity, and mycelia growing under BA stress avoid colonizing the surface of the growth surface, which leads to a suppression of aerial mycelium growth and surface conidia formation. BA penetrates into solid agar matrices, but the relative lack of oxygen below the substrate surface limits the effectiveness of BA in suppressing growth of embedded T. rubrum cells.

Boric acid inhibits LPS-induced TNF-alpha formation through a thiol-dependent mechanism in THP-1 cells.

PubMed

Cao, Jun; Jiang, Liping; Zhang, Xiaomei; Yao, Xiaofeng; Geng, Chengyan; Xue, Xiangxin; Zhong, Laifu

2008-01-01

Oxidative stress plays an important role during inflammatory diseases and antioxidant administration to diminish oxidative stress may arrest inflammatory processes. Boron has been implicated to modulate certain inflammatory mediators and regulate inflammatory processes. Here we investigated the role of the tripeptide glutathione (GSH) in modulating the effects of boric acid (BA) on lipopolysaccharide (LPS)-induced tumor necrosis factor alpha (TNF-alpha) formation in THP-1 monocytes. Interestingly, we found that BA had no significant effects on both TNF-alpha production and intracellular GSH contents, whereas it could inhibit LPS-induced TNF-alpha formation and ameliorated the d,l-buthionine-S,R-sulfoximine (BSO)-induced GSH depletion. Twenty-four hour incubation with BSO induced a decrease of the intracellular GSH and an increase of TNF-alpha. Treatment with N-acetyl-l-cysteine (NAC) did not significantly increase intracellular content of GSH but significantly reduced the secretion of TNF-alpha. BSO-pretreatment for 24h enhanced the LPS-induced secretion and mRNA expression of TNF-alpha further. BA inhibited LPS-stimulated TNF-alpha formation was also seen after GSH depletion by BSO. These results indicate that BA may have anti-inflammatory effect in the LPS-stimulated inflammation and the effect of BA on TNF-alpha secretion may be induced via a thiol-dependent mechanism.

Boric acid destabilizes the hyphal cytoskeleton and inhibits invasive growth of Candida albicans.

PubMed

Pointer, Benjamin R; Boyer, Michael P; Schmidt, Martin

2015-04-01

Exposure of Candida albicans to sub-lethal concentrations of boric acid (BA) restricts the dimorphic fungus to its yeast morphology and prevents the formation of invasive hyphae on solid substrates. Exposure to BA causes a rapid and reversible disappearance of polarisome and Spitzenkörper in growing hyphae. In BA-treated hyphae of C. albicans, actin quickly reorganizes from cytoplasmic cables to cortical patches and cell wall growth switches from an apical to an isotropic pattern. As a result of the cytoskeletal changes, the hyphal tips broaden and directional growth of hyphae ceases in the presence of BA. An analysis of homozygous deletion strains showed that mutants with constitutive or enhanced hyphal growth (tup1, nrg1, ssn6, rbf1) are BA-sensitive, demonstrating that cellular morphology is a major determinant of BA tolerance. The screening of deletion mutants also showed that deficiencies of the main activator of hyphal gene expression, Efg1, and the Rim101-signalling cascade, leading to Efg1 activation, cause BA resistance. Taken together, the data presented show that the selective inhibitory effect on BA on C. albicans hyphae is rooted in a disruption of apical cytoskeletal elements of growing hyphae. Copyright © 2015 John Wiley & Sons, Ltd.

Effect of Tumor Microenvironment on Selective Uptake of Boric Acid in HepG2 Human Hepatoma Cells.

PubMed

Bai, Yu-Chi; Hsia, Yu-Chun; Lin, Yu-Ting; Chen, Kuan-Hao; Chou, Fong-In; Yang, Chia-Min; Chuang, Yung-Jen

2017-11-01

Feasibility and efficacy of boric acid (BA)-mediated boron neutron capture therapy (BNCT) was first demonstrated by eliminating hepatocellular carcinoma (HCC) in a rat model. Furthermore, selective uptake of BA by liver tumor cells was shown in a rabbit model. To gain further insight, this study aimed to investigate the mechanisms of transportation and selective uptake of BA in HepG2 liver tumor cells. Transportation of BA in HepG2 cells was analyzed by time-course assays and by analyzing the rate of diffusion versus the concentration of BA. The effect of different tumor conditions on BA uptake was studied by treating HepG2 cells with 25 μg 10 B/ml BA under different concentrations of glucose, at different pH and in the presence of water-soluble cholesterol. HepG2 cells mainly uptake BA by simple diffusion. Cell membrane permeability may also contribute to tumor-specific uptake of BA. The selective uptake of BA was achieved primarily by diffusion, while other factors, such as low pH and increased membrane fluidity, which are hallmarks of HCC, might further enhance BA uptake. Copyright© 2017, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

Electrochemical growth of Co nanowires in ultra-high aspect ratio InP membranes: FFT-impedance spectroscopy of the growth process and magnetic properties.

PubMed

Gerngross, Mark-Daniel; Carstensen, Jürgen; Föll, Helmut

2014-01-01

The electrochemical growth of Co nanowires in ultra-high aspect ratio InP membranes has been investigated by fast Fourier transform-impedance spectroscopy (FFT-IS) in the frequency range from 75 Hz to 18.5 kHz. The impedance data could be fitted very well using an electric circuit equivalent model with a series resistance connected in series to a simple resistor-capacitor (RC) element and a Maxwell element. Based on the impedance data, the Co deposition in ultra-high aspect ratio InP membranes can be divided into two different Co deposition processes. The corresponding share of each process on the overall Co deposition can be determined directly from the transfer resistances of the two processes. The impedance data clearly show the beneficial impact of boric acid on the Co deposition and also indicate a diffusion limitation of boric acid in ultra-high aspect ratio InP membranes. The grown Co nanowires are polycrystalline with a very small grain size. They show a narrow hysteresis loop with a preferential orientation of the easy magnetization direction along the long nanowire axis due to the arising shape anisotropy of the Co nanowires.

Petrologic considerations for hot dry rock geothermal site selection in the Clear Lake Region, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stimac, J.; Goff, F.; Hearn, B.C. Jr.

1992-01-01

The Clear Lake area is well known for anomalous heat flow, thermal springs, hydrothermal mineral deposits, and Quaternary volcanism. These factors, along with the apparent lack of a large reservoir of geothermal fluid north of Collayomi fault make the Clear Lake area an attractive target for hot dry rock (HDR) geothermal development. Petrologic considerations provide some constraints on site selection for HDR development. Spatial and temporal trends in volcanism in the Coast Ranges indicate that magmatism has migrated to the north with time, paralleling passage of the Mendocino triple junction and propagation of the San Andreas fault. Volcanism in themore » region may have resulted from upwelling of hot asthenosphere along the southern margin of the subducted segment of the Gorda plate. Spatial and temporal trends of volcanism within the Clear Lake volcanic field are similar to larger-scale trends of Neogene volcanism in the Cost Ranges. Volcanism (especially for silicic compositions) shows a general migration to the north over the {approximately}2 Ma history of the field, with the youngest two silicic centers located at Mt. Konocti and Borax Lake. The Mt. Konocti system (active from {approximately} 0.6 to 0.3 Ma) was large and long-lived, whereas the Borax Lake system is much smaller but younger (0.09 Ma). Remnants of silicic magma bodies under Mt. Konocti may be in the latter stages of cooling, whereas a magma body centered under Borax Lake may be in the early stages of development. The existence of an upper crustal silicic magma body of under Borax Lake has yet to be demonstrated by passive geophysics, however, subsurface temperatures in the area as high (> 200{degrees}C at 2000 m) as those beneath the Mt. Konocti area. Based on petrologic considerations alone, the Mt. Konocti-Borax Lake area appears to be the most logical choice for HDR geothermal development in the region.« less

Selections From Kung-Jen JIH-PAO (Source Span: 9 May-30 June 1961) Number 7 -Communist China.

DTIC Science & Technology

1961-08-17

sulphate Ammonium hydrogen carbonate Sodium borate Titaniüm-iron powder Sodium fluoride Silicon dioxide Barium chloride beryllium carbonate ...Vinzenstrasse, 22a :■ P. 0. Box 3521 Aachen, Germany Washington 7> B.C. , Institute de Sociologie Solvay Rue du Chatelain, k9 Brussels, Belgium State... Sodium nitrite Specifications Pure n industrial Boric Acid " A^ua ammonia " Magnesium sulphate Industrial Manganese tedroxide Pure

Synthesis, characterization, molecular docking and in vitro antimalarial properties of new carboxamides bearing sulphonamide.

PubMed

Ugwu, D I; Okoro, U C; Ukoha, P O; Okafor, S; Ibezim, A; Kumar, N M

2017-07-28

Sulphonamides and carboxamides have shown large number of pharmacological properties against different types of diseases among which is malaria. Twenty four new carboxamide derivatives bearing benzenesulphonamoyl alkanamides were synthesized and investigated for their in silico and in vitro antimalarial and antioxidant properties. The substituted benzenesulphonyl chlorides (1a-c) were treated with various amino acids (2a-h) to obtain the benzenesulphonamoyl alkanamides (3a-x) which were subsequently treated with benzoyl chloride to obtain the N-benzoylated derivatives (5a-f, i-n and q-v). Further reactions of the N-benzoylated derivatives or proline derivatives with 4-aminoacetophenone (6) using boric acid as a catalyst gave the sulphonamide carboxamide derivatives (7a-x) in excellent yields. The in vitro antimalarial studies showed that all synthesized compounds had antimalarial property. Compound 7k, 7c, 7l, 7s, and 7j had mean MIC value of 0.02, 0.03, 0.05, 0.06 and 0.08 μM respectively comparable with chloroquine 0.06 μM. Compound 7c was the most potent antioxidant agent with IC 50 value of 0.045 mM comparable with 0.34 mM for ascorbic acid. In addition to the successful synthesis of the target molecules using boric acid catalysis, the compounds were found to have antimalarial and antioxidant activities comparable with known antimalarial and antioxidant drugs. The class of compounds reported herein have the potential of reducing oxidative stress arising from malaria parasite and chemotherapeutic agent used in the treatment of malaria. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Hierarchical porous photoanode based on acid boric catalyzed sol for dye sensitized solar cells

NASA Astrophysics Data System (ADS)

Maleki, Khatereh; Abdizadeh, Hossein; Golobostanfard, Mohammad Reza; Adelfar, Razieh

2017-02-01

The hierarchical porous photoanode of the dye sensitized solar cell (DSSC) is synthesized through non-aqueous sol-gel method based on H3BO3 as an acid catalyst and the efficiencies of the fabricated DSSC based on these photoanodes are compared. The sol parameters of 0.17 M, water mole ratio of 4.5, acid mole ratio of 0.45, and solvent type of ethanol are introduced as optimum parameters for photoanode formation without any detectable cracks. The optimized hierarchical photoanode mainly contains anatase phase with slight shift toward higher angles, confirming the doping of boron into titania structure. Moreover, the porous structure involves two ranges of average pore sizes of 20 and 635 nm. The diffuse reflectance spectroscopy (DRS) shows the proper scattering and blueshift in band gap. The paste parameters of solid:liquid, TiO2:ethyl cellulose, and terpineol:ethanol equal to 11:89, 3.5:7.5, and 25:64, respectively, are assigned as optimized parameters for this novel paste. The photovoltaic properties of short circuit current density, open circuit voltage, fill factor, and efficiency of 5.89 mA/cm2, 703 mV, 0.7, and 2.91% are obtained for the optimized sample, respectively. The relatively higher short circuit current of the main sample compared to other samples is mainly due to higher dye adsorption in this sample corresponding to its higher surface area and presumably higher charge transfer confirmed by low RS and Rct in electrochemical impedance spectroscopy data. Boric acid as a catalyst in titania sol not only forms hierarchical porous structure, but also dopes the titania lattice, which results in appreciated performance in this device.

Evaluation of the smear layer removal and erosive capacity of EDTA, boric acid, citric acid and desy clean solutions: an in vitro study.

PubMed

Turk, Tugba; Kaval, Mehmet Emin; Şen, Bilge Hakan

2015-09-03

The purpose of this study was to investigate the smear layer removal and erosive capacity of various irrigation solutions with sequential use of NaOCl on instrumented root canal walls. The root canals of single-rooted teeth were instrumented with ProTaper rotary instrument. Then, the teeth were randomly divided into five experimental groups. The root canals were irrigated with one of the following solutions (5 mL/1 min): 5% EDTA, 5% boric acid (BA), a mixture of BA and CA, 2.5% citric acid (CA) and 5% Desy Clean. After irrigating with 2.5% NaOCl and distilled water, the roots were split into two halves and each half was prepared for SEM examination. Representative photographs were taken from each third at x500 and x1000 magnifications. Double blind scoring was performed by two calibrated observers for smear layer and erosion. The scores were statistically analyzed using Kruskal-Wallis, Dunn's post hoc and Spearman's correlation tests (p = 0.05). There were statistically significant differences among the solutions by means of smear layer and erosion (p < 0.05). While 2.5% CA solution was the most effective solution in removal of smear layer, it was also the most erosive solution (p < 0.05). 5% Desy Clean removed smear layer effectively and caused less erosion. There was a negative, but statistically significant correlation between presence of smear layer and erosion (r = -0.684; p < 0.0001). Desy Clean can be a promising agent as an irrigation solution with optimal smear layer removal capacity and less erosive effects.

Simultaneous determination of active ingredients in Erigeron breviscapus (Vant.) Hand-Mazz. by capillary electrophoresis with electrochemical detection.

PubMed

Chu, Qingcui; Wu, Ting; Fu, Liang; Ye, Jiannong

2005-03-09

A high-performance capillary electrophoresis (CE) with electrochemical detection (ED) method was developed for the determination of the pharmacologically active ingredients in Erigeron breviscapus (Vant.) Hand-Mazz. and its extract phytopharmaceuticals in this work. Under the optimum conditions, nine analytes, baicalein, naringenin, scopoletin, kaempferol, apigenin, scutellarin, luteolin, caffeic acid and protocatechuic acid were separated within 24 min in a borax buffer (pH 8.7). Notably, excellent linearity was obtained over two orders of magnitude with detection limits (S/N=3) ranged from 1.0 x 10(-7) g/mL to 5.6 x 10(-7) g/mL for all nine analytes. This method was successfully used in the analysis of E. breviscapus (Vant.) Hand-Mazz. and its phytopharmaceuticals with a relatively simple extraction procedure, and the assay results were satisfactory.

Preliminary design and hazards report. Boiling Reactor Experiment V (BORAX V)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, R. E.

1960-02-01

The preliminary objectives of the proposed BORAX V program are to test nuclear superheating concepts and to advance the technology of boiling-water-reactor design by performing experiments which will improve the understanding of factors limiting the stability of boiling reactors at high power densities. The reactor vessel is a cylinder with ellipsoidal heads, made of carbon steel clad internally with stainless steel. Each of the three cores is 24 in. high and has an effective diameter of 39 in. This is a preliminary report. (W.D.M.)

Controls on the pH of hyper-saline lakes - A lesson from the Dead Sea

NASA Astrophysics Data System (ADS)

Golan, Rotem; Gavrieli, Ittai; Ganor, Jiwchar; Lazar, Boaz

2016-01-01

The pH of aqueous environments is determined by the dominant buffer systems of the water, defined operationally as total alkalinity (TA). The major buffer systems in the modern ocean are carbonic and boric acids of which the species bicarbonate, carbonate and borate make up about 77%, 19% and 4% of the TA, respectively. During the course of seawater evaporation (e.g. lagoons) the residual brine loses considerable portion of the dissolved inorganic carbon (DIC) and carbonate alkalinity (CA) already at the early stages of evaporation. DIC and CA decrease due to massive precipitation of CaCO3, while total boron (TB) increases conservatively, turning borate to the dominant alkalinity species in marine derived brines. In the present work we assess the apparent dissociation constant value of boric acid (KB‧) in saline and hypersaline waters, using the Dead Sea (DS) as a case study. We explain the DS low pH (∼6.3) and the effect of the boric and carbonic acid pK‧-s on the behavior of the brine's buffer system, including the pH increase that results from brine dilution. The KB‧ in DS was estimated from TB, TA, DIC and pH data measured in this study and early empirical data on artificial DS brines containing just carbonic acid. The KB‧ value was corroborated by Pitzer ion interaction model calculations using PHREEQC thermodynamic code applied to the chemical composition of the DS. Our results show that KB‧ increases considerably with the brine's ionic strength, reaching in the DS to a factor of 100 higher than in ;mean; seawater. Based on theoretical calculations and analyses of other natural brines it is suggested that brines' composition is a major factor in determining the KB‧ value and in turn the pH of such brines. We show that the higher the proportion of divalent cations in the brine the higher the dissociation constants of the weak acids (presumably due to formation of complexes). The low pH of the Dead Sea is accordingly explained by its extremely high ionic strength (TDS = 348 g/L) and the dominance of the divalent cation, Mg2+. Other natural hyper-saline brines with high concentration of divalent cations such as Kunteyi Lake in China and Don-Juan Pond in Antarctica follow the same general pattern. In contrast, the high pH of soda lakes results not only from their high TA but also by the dominance of the monovalent cation, Na+. Our study emphasizes the strong control of brine composition on pKB‧ and pH. These factors should be taken into consideration when reconstructing past and present environmental evaporitic environments.

Preparation of boron nitride fiber by organic precursor method

NASA Astrophysics Data System (ADS)

Zhou, Yingying; Sun, Runjun; Zhang, Zhaohuan; Fan, Wei; Zhou, Dan; Sheng, Cuihong

In this paper, boron nitride polymer precursor was made by boric acid, melamine, twelve sodium alkyl sulfate as raw materials and pure water as medium which is heated to 70 °C. Boron nitride precursor polymer was soluble in formic acid solution. The boron nitride precursor can be electrostatically spun at the voltage in 23 kV and the distance between the positive and negative poles is 15 cm. The formed fiber is very uniform. The properties of the precursors were analyzed through electron microscope, infrared spectrum, X-ray and ultraviolet spectrum. The aim of the job is to got the precursor of BN and spun it.

Red photoluminescence BCNO synthesized from graphene oxide nanosheets

NASA Astrophysics Data System (ADS)

Kang, Yue; Chu, Zeng-yong; Ma, Tian; Li, Wei-ping; Zhang, Dong-jiu; Tang, Xiao-yu

2016-01-01

In this paper, we demonstrate the conversion of graphene oxide (GO) into boron carbon oxynitride (BCNO) hybrid nanosheets via a reaction with boric acid and urea, during which the boron and nitrogen atoms are incorporated into graphene nanosheets. The experimental results reveal that GO is important for the photoluminescence (PL) BCNO phosphor particles. More importantly, in this system, the prepared BCNO phosphors can be used to prepare the materials needed for red light emitting diodes (LEDs).

Effect of basalt fibres reinforcement and aluminum trihydrate on the thermal properties of intumescent fire retardant coatings

NASA Astrophysics Data System (ADS)

Yasir, Muhammad; Amir, Norlaili Binti; Ahmad, Faiz; Syahirah Rodzhan, N.

2017-08-01

This research is carried out in order to study the synergistic effect of aluminium trihydrate and basalt fibres on the properties of fire resistant intumescent coatings. Intumescent fire retardant coatings were developed using different flame retardants such as ammonium polyphosphate, expandable graphite, melamine and boric acid. These flame retardants were bound together with the help of epoxy binder along with curing agent. Furthermore, individual and combinations of aluminium trihydrate and basalt fibres was incorporated in the formulations to analyse mechanical and chemical properties of the coatings. Char expansion was observed using furnace test, thermogravimetric analysis was used to determine residual weight, X-Ray Diffraction was performed to investigate compounds present in the char, shear test was conducted to determine char strength and scanning electron microscopy analysis was performed to observe morphology of the burnt char. From the microscopic investigation it was concluded that the dense structure of the char increased the char integrity by adding basalt and aluminium trihydrate as fillers. X-Ray Diffraction results shows the presence boron phosphate, and boric acid which enhanced the thermal performance of the coating up to 800°C. From the Thermogravimetric analysis it was concluded that the residual weight of the char was increased up to 34.9 % for IC-B2A4 which enhanced thermal performance of intumescent coating.

Dose-dependent Effect of Boric Acid on Myogenic Differentiation of Human Adipose-derived Stem Cells (hADSCs).

PubMed

Apdik, Hüseyin; Doğan, Ayşegül; Demirci, Selami; Aydın, Safa; Şahin, Fikrettin

2015-06-01

Boron, a vital micronutrient for plant metabolism, is not fully elucidated for embryonic and adult body development, and tissue regeneration. Although optimized amount of boron supplement has been shown to be essential for normal gestational development in zebrafish and frog and beneficial for bone regeneration in higher animals, effects of boron on myogenesis and myo-regeneration remains to be solved. In the current study, we investigated dose-dependent activity of boric acid on myogenic differentiation of human adipose-derived stem cells (hADSCs) using immunocytochemical, gene, and protein expression analysis. The results revealed that while low- (81.9 μM) and high-dose (819.6 μM) boron treatment increased myogenic gene expression levels such as myosin heavy chain (MYH), MyoD, myogenin, and desmin at day 4 of differentiation, high-dose treatment decreased myogenic-related gene and protein levels at day 21 of differentiation, confirmed by immunocytochemical analysis. The findings of the study present not only an understanding of boron's effect on myogenic differentiation but also an opportunity for the development of scaffolds to be used in skeletal tissue engineering and supplements for embryonic muscle growth. However, fine dose tuning and treatment period arranging are highly warranted as boron treatment over required concentrations and time might result in detrimental outcomes to myogenesis and myo-regeneration.

The neuroprotective role of boric acid on aluminum chloride-induced neurotoxicity.

PubMed

Colak, Suat; Geyikoglu, Fatime; Keles, Osman Nuri; Türkez, Hasan; Topal, Ahmet; Unal, Bünyami

2011-09-01

This study was designed to investigate the qualitative and quantitative changes in brain tissue following aluminum chloride (AlCl(3)) administration and to determine whether boric acid (BA) has a protective effect against brain damage induced by AlCl( 3). For this aim, Sprague-Dawley rats were randomly separated into eight groups: (1) control, (2) AlCl(3) (5 mg/kg/day), (3, 4 and 5) BA (3.25, 36 and 58.5 mg/kg/day), (6, 7 and 8) AlCl(3) (5 mg/kg/day) plus BA (3.25, 36 and 58.5 mg/kg/day). After the animals were killed, the total numbers of neuron in the brain of all groups were determined using an unbiased stereological analysis. In addition to the stereological analysis, all brains were examined histopathologically by using light and electron microscopy. The stereological and histopathological results indicated a high damage of the rat brain tissues in the AlCl(3) and AlCl(3) + high dose BA (36 and 58.5) treatment groups. However, protective effects on neuron were observed in the AlCl(3) + low dose BA (3.25) group when compared other AlCl(3) groups. Our stereological and histopathological findings show that low-dose BA, as a proteasome inhibitor, can decrease the adverse effects of AlCl(3) on the cerebral cortex.

Boric acid-dependent decrease in regulatory histone H3 acetylation is not mutagenic in yeast.

PubMed

Pointer, Benjamin R; Schmidt, Martin

2016-07-01

Candida albicans is a dimorphic yeast commonly found on human mucosal membranes that switches from yeast to hyphal morphology in response to environmental factors. The change to hyphal growth requires histone H3 modifications by the yeast-specific histone acetyltransferase Rtt109. In addition to its role in morphogenesis, Rtt109-dependent acetylation of histone H3 lysine residues 9 and 56 has regulatory functions during DNA replication and repair. Boric acid (BA) is a broad-spectrum agent that specifically inhibits C. albicans hyphal growth, locking the fungus in its harmless commensal yeast state. The present study characterizes the effect of BA on C. albicans histone acetylation in respect to specificity, time-course and significance. We demonstrate that sublethal concentrations of BA reduce H3K9/H3K56 acetylation, both on a basal level and in response to genotoxic stress. Acetylation at other selected histone sites were not affected by BA. qRT-PCR expression analysis of the DNA repair gene Rad51 indicated no elevated level of genotoxic stress during BA exposure. A forward-mutation analysis demonstrated the BA does not increase spontaneous or induced mutations. The findings suggest that DNA repair remains effective even when histone H3 acetylation decreases and dispels the notion that BA treatment impairs genome integrity in yeast. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Ultrasonic Phased Array Evaluation of Control Rod Drive Mechanism (CRDM) Nozzle Interference Fit and Weld Region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cinson, Anthony D.; Crawford, Susan L.; MacFarlan, Paul J.

2011-07-31

Ultrasonic phased array data were collected on a removed-from-service CRDM nozzle specimen to assess a previously reported leak path. First a mock-up CRDM specimen was evaluated that contained two 0.076-mm (3.0-mil) interference fit regions formed from an actual Inconel CRDM tube and two 152.4-mm (6.0-in.) thick carbon steel blocks. One interference fit region has a series of precision crafted electric discharge machining (EDM) notches at various lengths, widths, depths, and spatial separations for establishing probe sensitivity, resolution and calibration. The other interference fit has zones of boric acid (crystal form) spaced periodically between the tube and block to represent anmore » actively leaking CRDM nozzle assembly in the field. Ultrasonic phased-array evaluations were conducted using an immersion 8-element annular 5.0-MHz probe from the tube inner diameter (ID). A variety of focal laws were employed to evaluate the interference fit regions and J grove weld, where applicable. Responses from the mock-up specimen were evaluated to determine detection limits and characterization ability as well as contrast the ultrasonic response differences with the presence of boric acid in the fit region. Nozzle 63, from the North Anna Unit-2 nuclear power plant, was evaluated to assess leakage path(s) and was destructively dismantled to allow a visual verification of the leak path(s).« less

Green synthesis of boron doped graphene and its application as high performance anode material in Li ion battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sahoo, Madhumita; Sreena, K.P.; Vinayan, B.P.

2015-01-15

Graphical abstract: Boron doped graphene (B-G), synthesized by simple hydrogen induced reduction technique using boric acid as boron precursor, have more uneven surface as a result of smaller bonding distance of boron compared to carbon, showed high capacity and high rate capability compared to pristine graphene as an anode material for Li ion battery application. - Abstract: The present work demonstrates a facile route for the large-scale, catalyst free, and green synthesis approach of boron doped graphene (B-G) and its use as high performance anode material for Li ion battery (LIB) application. Boron atoms were doped into graphene framework withmore » an atomic percentage of 5.93% via hydrogen induced thermal reduction technique using graphite oxide and boric acid as precursors. Various characterization techniques were used to confirm the boron doping in graphene sheets. B-G as anode material shows a discharge capacity of 548 mAh g{sup −1} at 100 mA g{sup −1} after 30th cycles. At high current density value of 1 A g{sup −1}, B-G as anode material enhances the specific capacity by about 1.7 times compared to pristine graphene. The present study shows a simplistic way of boron doping in graphene leading to an enhanced Li ion adsorption due to the change in electronic states.« less

Evaluation of bactericidal effect of three antiseptics on bacteria isolated from wounds.

PubMed

Kumara, D U A; Fernando, S S N; Kottahachchi, J; Dissanayake, D M B T; Athukorala, G I D D A D; Chandrasiri, N S; Damayanthi, K W N; Hemarathne, M H S L; Pathirana, A A

2015-01-01

Antiseptics are widely used in wound management to prevent or treat wound infections due to their proven wound healing properties regardless of their cytotoxicity. The objective of this study was to determine the bactericidal effects of three antiseptics on pathogens known to cause wound infections. The study was carried out at a tertiary care hospital and a university microbiology laboratory in Sri Lanka in 2013. The three acids (acetic acid, ascorbic acid and boric acid) in increasing concentration (0.5%, 0.75% and 1%) were tested against bacterial suspensions equivalent to 0.5 McFarland standard. The Bacteria isolates used were isolated from wound and standard strains of Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. There were 33 (68.8%) Coliforms, 10 (20.8%) Pseudomonas species, and 5 (10.4%) strains of Staphylococcus aureus. Acetic acid at concentration of 0.5% inhibited growth of 37 (77%) and 42 (87.5%) of tested isolates when exposed for 30 and 60 minutes, respectively. However 100% inhibition was achieved at four hours. At a concentration of 0.75%, 40 (83.3%) and 44 (91.7%) were inhibited when exposed for 30 and 60 minutes, respectively, with 100% inhibition at 4 hours. At concentration of 1%, 46 (95.8%) inhibition was seen at 30 minutes and 100% inhibition at 60 minutes. Ascorbic acid, at 0.5% and 0.75 % concentrations, inhibited growth of 45(93.7%) and 47(97.9%) of isolates respectively when exposed for 30 minutes. At these two concentrations, 100% inhibition was achieved when exposed for one hour. At 1% concentration, 100% inhibition was achieved at 30 minutes. Boric acid did not show bactericidal effect at concentrations of 0.5%, 0.75 % and 1%. Pseudomonas species were inhibited at 30 minutes by 0.5% acetic acid. Bactericidal effect against all the standard strains was seen with three acids at each concentration tested from 30 minutes onwards Ascorbic acid was bactericidal for all organisms tested within the shortest exposure time at the lowest concentration compared to other two acids. Despite promising bactericidal effects, further studies warrant, as ongoing debates on toxicity of acids on tissue epithelialisation. Application of antiseptics for a shorter duration could overcome this problem without losing bactericidal activity. The authors have no conflict of interest and no funding was received for this study.

Fluorometric determination of zirconium in minerals

USGS Publications Warehouse

Alford, W.C.; Shapiro, L.; White, C.E.

1951-01-01

The increasing use of zirconium in alloys and in the ceramics industry has created renewed interest in methods for its determination. It is a common constituent of many minerals, but is usually present in very small amounts. Published methods tend to be tedious, time-consuming, and uncertain as to accuracy. A new fluorometric procedure, which overcomes these objections to a large extent, is based on the blue fluorescence given by zirconium and flavonol in sulfuric acid solution. Hafnium is the only element that interferes. The sample is fused with borax glass and sodium carbonate and extracted with water. The residue is dissolved in sulfuric acid, made alkaline with sodium hydroxide to separate aluminum, and filtered. The precipitate is dissolved in sulfuric acid and electrolysed in a Melaven cell to remove iron. Flavonol is then added and the fluorescence intensity is measured with a photo-fluorometer. Analysis of seven standard mineral samples shows excellent results. The method is especially useful for minerals containing less than 0.25% zirconium oxide.

The relationship of blood- and urine-boron to boron exposure in borax-workers and usefulness of urine-boron as an exposure marker.

PubMed Central

Culver, B D; Shen, P T; Taylor, T H; Lee-Feldstein, A; Anton-Culver, H; Strong, P L

1994-01-01

Daily dietary-boron intake and on-the-job inspired boron were compared with blood- and urine-boron concentrations in workers engaged in packaging and shipping borax. Fourteen workers handling borax at jobs of low, medium, and high dust exposures were sampled throughout full shifts for 5 consecutive days each. Airborne borax concentrations ranged from means of 3.3 mg/m3 to 18 mg/m3, measured gravimetrically. End-of-shift mean blood-boron concentrations ranged from 0.11 to 0.26 microgram/g; end-of-shift mean urine concentrations ranged from 3.16 to 10.72 micrograms/mg creatinine. Creatinine measures were used to adjust for differences in urine-specific gravity such that 1 ml of urine contains approximately 1 mg creatinine. There was no progressive increase in end-of-shift blood- or urine-boron concentrations across the days of the week. Urine testing done at the end of the work shift gave a somewhat better estimate of borate exposure than did blood testing, was sampled more easily, and was analytically less difficult to perform. Personal air samplers of two types were used: one, the 37-mm closed-face, two-piece cassette to estimate total dust and the other, the Institute of Occupational Medicine (IOM) sampler to estimate inspirable particulate mass. Under the conditions of this study, the IOM air sampler more nearly estimated human exposure as measured by blood- and urine-boron levels than did the sampler that measured total dust.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7889874