Main steam line break accident simulation of APR1400 using the model of ATLAS facility

NASA Astrophysics Data System (ADS)

Ekariansyah, A. S.; Deswandri; Sunaryo, Geni R.

2018-02-01

A main steam line break simulation for APR1400 as an advanced design of PWR has been performed using the RELAP5 code. The simulation was conducted in a model of thermal-hydraulic test facility called as ATLAS, which represents a scaled down facility of the APR1400 design. The main steam line break event is described in a open-access safety report document, in which initial conditions and assumptionsfor the analysis were utilized in performing the simulation and analysis of the selected parameter. The objective of this work was to conduct a benchmark activities by comparing the simulation results of the CESEC-III code as a conservative approach code with the results of RELAP5 as a best-estimate code. Based on the simulation results, a general similarity in the behavior of selected parameters was observed between the two codes. However the degree of accuracy still needs further research an analysis by comparing with the other best-estimate code. Uncertainties arising from the ATLAS model should be minimized by taking into account much more specific data in developing the APR1400 model.

The solution of the dam-break problem in the Porous Shallow water Equations

NASA Astrophysics Data System (ADS)

Cozzolino, Luca; Pepe, Veronica; Cimorelli, Luigi; D'Aniello, Andrea; Della Morte, Renata; Pianese, Domenico

2018-04-01

The Porous Shallow water Equations are commonly used to evaluate the propagation of flooding waves in the urban environment. These equations may exhibit not only classic shocks, rarefactions, and contact discontinuities, as in the ordinary two-dimensional Shallow water Equations, but also special discontinuities at abrupt porosity jumps. In this paper, an appropriate parameterization of the stationary weak solutions of one-dimensional Porous Shallow water Equations supplies the inner structure of the porosity jumps. The exact solution of the corresponding dam-break problem is presented, and six different wave configurations are individuated, proving that the solution exists and it is unique for given initial conditions and geometric characteristics. These results can be used as a benchmark in order to validate one- and two-dimensional numerical models for the solution of the Porous Shallow water Equations. In addition, it is presented a novel Finite Volume scheme where the porosity jumps are taken into account by means of a variables reconstruction approach. The dam-break results supplied by this numerical scheme are compared with the exact dam-break results, showing the promising capabilities of this numerical approach. Finally, the advantages of the novel porosity jump definition are shown by comparison with other definitions available in the literature, demonstrating its advantages, and the issues raising in real world applications are discussed.

Benchmarking homogenization algorithms for monthly data

NASA Astrophysics Data System (ADS)

Venema, V. K. C.; Mestre, O.; Aguilar, E.; Auer, I.; Guijarro, J. A.; Domonkos, P.; Vertacnik, G.; Szentimrey, T.; Stepanek, P.; Zahradnicek, P.; Viarre, J.; Müller-Westermeier, G.; Lakatos, M.; Williams, C. N.; Menne, M. J.; Lindau, R.; Rasol, D.; Rustemeier, E.; Kolokythas, K.; Marinova, T.; Andresen, L.; Acquaotta, F.; Fratianni, S.; Cheval, S.; Klancar, M.; Brunetti, M.; Gruber, C.; Prohom Duran, M.; Likso, T.; Esteban, P.; Brandsma, T.

2012-01-01

The COST (European Cooperation in Science and Technology) Action ES0601: advances in homogenization methods of climate series: an integrated approach (HOME) has executed a blind intercomparison and validation study for monthly homogenization algorithms. Time series of monthly temperature and precipitation were evaluated because of their importance for climate studies and because they represent two important types of statistics (additive and multiplicative). The algorithms were validated against a realistic benchmark dataset. The benchmark contains real inhomogeneous data as well as simulated data with inserted inhomogeneities. Random independent break-type inhomogeneities with normally distributed breakpoint sizes were added to the simulated datasets. To approximate real world conditions, breaks were introduced that occur simultaneously in multiple station series within a simulated network of station data. The simulated time series also contained outliers, missing data periods and local station trends. Further, a stochastic nonlinear global (network-wide) trend was added. Participants provided 25 separate homogenized contributions as part of the blind study. After the deadline at which details of the imposed inhomogeneities were revealed, 22 additional solutions were submitted. These homogenized datasets were assessed by a number of performance metrics including (i) the centered root mean square error relative to the true homogeneous value at various averaging scales, (ii) the error in linear trend estimates and (iii) traditional contingency skill scores. The metrics were computed both using the individual station series as well as the network average regional series. The performance of the contributions depends significantly on the error metric considered. Contingency scores by themselves are not very informative. Although relative homogenization algorithms typically improve the homogeneity of temperature data, only the best ones improve precipitation data. Training the users on homogenization software was found to be very important. Moreover, state-of-the-art relative homogenization algorithms developed to work with an inhomogeneous reference are shown to perform best. The study showed that automatic algorithms can perform as well as manual ones.

Benchmarking monthly homogenization algorithms

NASA Astrophysics Data System (ADS)

Venema, V. K. C.; Mestre, O.; Aguilar, E.; Auer, I.; Guijarro, J. A.; Domonkos, P.; Vertacnik, G.; Szentimrey, T.; Stepanek, P.; Zahradnicek, P.; Viarre, J.; Müller-Westermeier, G.; Lakatos, M.; Williams, C. N.; Menne, M.; Lindau, R.; Rasol, D.; Rustemeier, E.; Kolokythas, K.; Marinova, T.; Andresen, L.; Acquaotta, F.; Fratianni, S.; Cheval, S.; Klancar, M.; Brunetti, M.; Gruber, C.; Prohom Duran, M.; Likso, T.; Esteban, P.; Brandsma, T.

2011-08-01

The COST (European Cooperation in Science and Technology) Action ES0601: Advances in homogenization methods of climate series: an integrated approach (HOME) has executed a blind intercomparison and validation study for monthly homogenization algorithms. Time series of monthly temperature and precipitation were evaluated because of their importance for climate studies and because they represent two important types of statistics (additive and multiplicative). The algorithms were validated against a realistic benchmark dataset. The benchmark contains real inhomogeneous data as well as simulated data with inserted inhomogeneities. Random break-type inhomogeneities were added to the simulated datasets modeled as a Poisson process with normally distributed breakpoint sizes. To approximate real world conditions, breaks were introduced that occur simultaneously in multiple station series within a simulated network of station data. The simulated time series also contained outliers, missing data periods and local station trends. Further, a stochastic nonlinear global (network-wide) trend was added. Participants provided 25 separate homogenized contributions as part of the blind study as well as 22 additional solutions submitted after the details of the imposed inhomogeneities were revealed. These homogenized datasets were assessed by a number of performance metrics including (i) the centered root mean square error relative to the true homogeneous value at various averaging scales, (ii) the error in linear trend estimates and (iii) traditional contingency skill scores. The metrics were computed both using the individual station series as well as the network average regional series. The performance of the contributions depends significantly on the error metric considered. Contingency scores by themselves are not very informative. Although relative homogenization algorithms typically improve the homogeneity of temperature data, only the best ones improve precipitation data. Training was found to be very important. Moreover, state-of-the-art relative homogenization algorithms developed to work with an inhomogeneous reference are shown to perform best. The study showed that currently automatic algorithms can perform as well as manual ones.

Evaluating the Quantitative Capabilities of Metagenomic Analysis Software.

PubMed

Kerepesi, Csaba; Grolmusz, Vince

2016-05-01

DNA sequencing technologies are applied widely and frequently today to describe metagenomes, i.e., microbial communities in environmental or clinical samples, without the need for culturing them. These technologies usually return short (100-300 base-pairs long) DNA reads, and these reads are processed by metagenomic analysis software that assign phylogenetic composition-information to the dataset. Here we evaluate three metagenomic analysis software (AmphoraNet--a webserver implementation of AMPHORA2--, MG-RAST, and MEGAN5) for their capabilities of assigning quantitative phylogenetic information for the data, describing the frequency of appearance of the microorganisms of the same taxa in the sample. The difficulties of the task arise from the fact that longer genomes produce more reads from the same organism than shorter genomes, and some software assign higher frequencies to species with longer genomes than to those with shorter ones. This phenomenon is called the "genome length bias." Dozens of complex artificial metagenome benchmarks can be found in the literature. Because of the complexity of those benchmarks, it is usually difficult to judge the resistance of a metagenomic software to this "genome length bias." Therefore, we have made a simple benchmark for the evaluation of the "taxon-counting" in a metagenomic sample: we have taken the same number of copies of three full bacterial genomes of different lengths, break them up randomly to short reads of average length of 150 bp, and mixed the reads, creating our simple benchmark. Because of its simplicity, the benchmark is not supposed to serve as a mock metagenome, but if a software fails on that simple task, it will surely fail on most real metagenomes. We applied three software for the benchmark. The ideal quantitative solution would assign the same proportion to the three bacterial taxa. We have found that AMPHORA2/AmphoraNet gave the most accurate results and the other two software were under-performers: they counted quite reliably each short read to their respective taxon, producing the typical genome length bias. The benchmark dataset is available at http://pitgroup.org/static/3RandomGenome-100kavg150bps.fna.

A new Nawaz-Enscore-Ham-based heuristic for permutation flow-shop problems with bicriteria of makespan and machine idle time

NASA Astrophysics Data System (ADS)

Liu, Weibo; Jin, Yan; Price, Mark

2016-10-01

A new heuristic based on the Nawaz-Enscore-Ham algorithm is proposed in this article for solving a permutation flow-shop scheduling problem. A new priority rule is proposed by accounting for the average, mean absolute deviation, skewness and kurtosis, in order to fully describe the distribution style of processing times. A new tie-breaking rule is also introduced for achieving effective job insertion with the objective of minimizing both makespan and machine idle time. Statistical tests illustrate better solution quality of the proposed algorithm compared to existing benchmark heuristics.

Study of molecular carbon-hydrogen bond dissociation during shock compression

NASA Astrophysics Data System (ADS)

Hammel, Ben; Hawreliak, James

2017-06-01

Advancements in theory and experiment show that chemical interactions in warm dense mixtures play a non-negligible role in the high-temperature and high-pressure properties of a molecular compound. For example, recent work on polystyrene has observed features suggestive of molecular dissociation - non-linear ``kinks'' are evident in the material's Hugoniot, consistent with CH bond breaking. The assumption used in linear mixing models, that species are chemically inert, breaks down in warm dense mixtures. At the Institute for Shock Physics, we are developing the necessary capabilities to perform high-repetition-rate experiments needed to map out chemical-reaction features along a material's Hugoniot. Initially, we plan to benchmark our work to the data taken by Barrios et al., by reproducing the observed kink in the polystyrene Hugoniot. We then extend this capability to explore polypropylene, CH2, where we expect to observe multiple kink features - representative of the disassociation of multiple CH bonds. Work supported by DOE/NNSA, DOE/SC-OFES and Murdock Charitable Trust.

RUBIC identifies driver genes by detecting recurrent DNA copy number breaks

PubMed Central

van Dyk, Ewald; Hoogstraat, Marlous; ten Hoeve, Jelle; Reinders, Marcel J. T.; Wessels, Lodewyk F. A.

2016-01-01

The frequent recurrence of copy number aberrations across tumour samples is a reliable hallmark of certain cancer driver genes. However, state-of-the-art algorithms for detecting recurrent aberrations fail to detect several known drivers. In this study, we propose RUBIC, an approach that detects recurrent copy number breaks, rather than recurrently amplified or deleted regions. This change of perspective allows for a simplified approach as recursive peak splitting procedures and repeated re-estimation of the background model are avoided. Furthermore, we control the false discovery rate on the level of called regions, rather than at the probe level, as in competing algorithms. We benchmark RUBIC against GISTIC2 (a state-of-the-art approach) and RAIG (a recently proposed approach) on simulated copy number data and on three SNP6 and NGS copy number data sets from TCGA. We show that RUBIC calls more focal recurrent regions and identifies a much larger fraction of known cancer genes. PMID:27396759

The linear -- non-linear frontier for the Goldstone Higgs

DOE PAGES

Gavela, M. B.; Kanshin, K.; Machado, P. A. N.; ...

2016-12-01

The minimalmore » $SO(5)/SO(4)$ sigma model is used as a template for the ultraviolet completion of scenarios in which the Higgs particle is a low-energy remnant of some high-energy dynamics, enjoying a (pseudo) Nambu-Goldstone boson ancestry. Varying the $$\\sigma$$ mass allows to sweep from the perturbative regime to the customary non-linear implementations. The low-energy benchmark effective non-linear Lagrangian for bosons and fermions is obtained, determining as well the operator coefficients including linear corrections. At first order in the latter, three effective bosonic operators emerge which are independent of the explicit soft breaking assumed. The Higgs couplings to vector bosons and fermions turn out to be quite universal: the linear corrections are proportional to the explicit symmetry breaking parameters. Furthermore, we define an effective Yukawa operator which allows a simple parametrization and comparison of different heavy fermion ultraviolet completions. In addition, one particular fermionic completion is explored in detail, obtaining the corresponding leading low-energy fermionic operators.« less

A Complex Network Theory Approach for the Spatial Distribution of Fire Breaks in Heterogeneous Forest Landscapes for the Control of Wildland Fires

PubMed Central

Russo, Lucia; Russo, Paola; Siettos, Constantinos I.

2016-01-01

Based on complex network theory, we propose a computational methodology which addresses the spatial distribution of fuel breaks for the inhibition of the spread of wildland fires on heterogeneous landscapes. This is a two-level approach where the dynamics of fire spread are modeled as a random Markov field process on a directed network whose edge weights are determined by a Cellular Automata model that integrates detailed GIS, landscape and meteorological data. Within this framework, the spatial distribution of fuel breaks is reduced to the problem of finding network nodes (small land patches) which favour fire propagation. Here, this is accomplished by exploiting network centrality statistics. We illustrate the proposed approach through (a) an artificial forest of randomly distributed density of vegetation, and (b) a real-world case concerning the island of Rhodes in Greece whose major part of its forest was burned in 2008. Simulation results show that the proposed methodology outperforms the benchmark/conventional policy of fuel reduction as this can be realized by selective harvesting and/or prescribed burning based on the density and flammability of vegetation. Interestingly, our approach reveals that patches with sparse density of vegetation may act as hubs for the spread of the fire. PMID:27780249

A Complex Network Theory Approach for the Spatial Distribution of Fire Breaks in Heterogeneous Forest Landscapes for the Control of Wildland Fires.

PubMed

Russo, Lucia; Russo, Paola; Siettos, Constantinos I

2016-01-01

Based on complex network theory, we propose a computational methodology which addresses the spatial distribution of fuel breaks for the inhibition of the spread of wildland fires on heterogeneous landscapes. This is a two-level approach where the dynamics of fire spread are modeled as a random Markov field process on a directed network whose edge weights are determined by a Cellular Automata model that integrates detailed GIS, landscape and meteorological data. Within this framework, the spatial distribution of fuel breaks is reduced to the problem of finding network nodes (small land patches) which favour fire propagation. Here, this is accomplished by exploiting network centrality statistics. We illustrate the proposed approach through (a) an artificial forest of randomly distributed density of vegetation, and (b) a real-world case concerning the island of Rhodes in Greece whose major part of its forest was burned in 2008. Simulation results show that the proposed methodology outperforms the benchmark/conventional policy of fuel reduction as this can be realized by selective harvesting and/or prescribed burning based on the density and flammability of vegetation. Interestingly, our approach reveals that patches with sparse density of vegetation may act as hubs for the spread of the fire.

C6 Coefficients and Dipole Polarizabilities for All Atoms and Many Ions in Rows 1-6 of the Periodic Table.

PubMed

Gould, Tim; Bučko, Tomáš

2016-08-09

Using time-dependent density functional theory (TDDFT) with exchange kernels, we calculate and test imaginary frequency-dependent dipole polarizabilities for all atoms and many ions in rows 1-6 of the periodic table. These are then integrated over frequency to produce C6 coefficients. Results are presented under different models: straight TDDFT calculations using two different kernels; "benchmark" TDDFT calculations corrected by more accurate quantum chemical and experimental data; and "benchmark" TDDFT with frozen orbital anions. Parametrizations are presented for 411+ atoms and ions, allowing results to be easily used by other researchers. A curious relationship, C6,XY ∝ [αX(0)αY(0)](0.73), is found between C6 coefficients and static polarizabilities α(0). The relationship C6,XY = 2C6,XC6,Y/[(αX/αY)C6,Y + (αY/αX)C6,X] is tested and found to work well (<5% errors) in ∼80% of the cases, but can break down badly (>30% errors) in a small fraction of cases.

Alignment limit of the NMSSM Higgs sector

DOE PAGES

Carena, Marcela; Haber, Howard E.; Low, Ian; ...

2016-02-17

The Next-to-Minimal Supersymmetric extension of the Standard Model (NMSSM) with a Higgs boson of mass 125 GeV can be compatible with stop masses of order of the electroweak scale, thereby reducing the degree of fine-tuning necessary to achieve electroweak symmetry breaking. Moreover, in an attractive region of the NMSSM parameter space, corresponding to the \\alignment limit" in which one of the neutral Higgs fields lies approximately in the same direction in field space as the doublet Higgs vacuum expectation value, the observed Higgs boson is predicted to have Standard- Model-like properties. We derive analytical expressions for the alignment conditions andmore » show that they point toward a more natural region of parameter space for electroweak symmetry breaking, while allowing for perturbativity of the theory up to the Planck scale. Additionally, the alignment limit in the NMSSM leads to a well defined spectrum in the Higgs and Higgsino sectors, and yields a rich and interesting Higgs boson phenomenology that can be tested at the LHC. Here, we discuss the most promising channels for discovery and present several benchmark points for further study.« less

You Spin my Head Right Round: Threshold of Limited Immersion for Rotation Gains in Redirected Walking.

PubMed

Schmitz, Patric; Hildebrandt, Julian; Valdez, Andre Calero; Kobbelt, Leif; Ziefle, Martina

2018-04-01

In virtual environments, the space that can be explored by real walking is limited by the size of the tracked area. To enable unimpeded walking through large virtual spaces in small real-world surroundings, redirection techniques are used. These unnoticeably manipulate the user's virtual walking trajectory. It is important to know how strongly such techniques can be applied without the user noticing the manipulation-or getting cybersick. Previously, this was estimated by measuring a detection threshold (DT) in highly-controlled psychophysical studies, which experimentally isolate the effect but do not aim for perceived immersion in the context of VR applications. While these studies suggest that only relatively low degrees of manipulation are tolerable, we claim that, besides establishing detection thresholds, it is important to know when the user's immersion breaks. We hypothesize that the degree of unnoticed manipulation is significantly different from the detection threshold when the user is immersed in a task. We conducted three studies: a) to devise an experimental paradigm to measure the threshold of limited immersion (TLI), b) to measure the TLI for slowly decreasing and increasing rotation gains, and c) to establish a baseline of cybersickness for our experimental setup. For rotation gains greater than 1.0, we found that immersion breaks quite late after the gain is detectable. However, for gains lesser than 1.0, some users reported a break of immersion even before established detection thresholds were reached. Apparently, the developed metric measures an additional quality of user experience. This article contributes to the development of effective spatial compression methods by utilizing the break of immersion as a benchmark for redirection techniques.

Analytical expression for a class of spherically symmetric solutions in Lorentz-breaking massive gravity

NASA Astrophysics Data System (ADS)

Li, Ping; Li, Xin-zhou; Xi, Ping

2016-06-01

We present a detailed study of the spherically symmetric solutions in Lorentz-breaking massive gravity. There is an undetermined function { F }(X,{w}1,{w}2,{w}3) in the action of Stückelberg fields {S}φ ={{{Λ }}}4\\int {{{d}}}4x\\sqrt{-g}{ F }, which should be resolved through physical means. In general relativity, the spherically symmetric solution to the Einstein equation is a benchmark and its massive deformation also plays a crucial role in Lorentz-breaking massive gravity. { F } will satisfy the constraint equation {T}01=0 from the spherically symmetric Einstein tensor {G}01=0, if we maintain that any reasonable physical theory should possess the spherically symmetric solutions. The Stückelberg field {φ }i is taken as a ‘hedgehog’ configuration {φ }i=φ (r){x}i/r, whose stability is guaranteed by the topological one. Under this ansätz, {T}01=0 is reduced to d{ F }=0. The functions { F } for d{ F }=0 form a commutative ring {R}{ F }. We obtain an expression of the solution to the functional differential equation with spherical symmetry if { F }\\in {R}{ F }. If { F }\\in {R}{ F } and \\partial { F }/\\partial X=0, the functions { F } form a subring {S}{ F }\\subset {R}{ F }. We show that the metric is Schwarzschild, Schwarzschild-AdS or Schwarzschild-dS if { F }\\in {S}{ F }. When { F }\\in {R}{ F } but { F }\

Combinations of coupled cluster, density functionals, and the random phase approximation for describing static and dynamic correlation, and van der Waals interactions

NASA Astrophysics Data System (ADS)

Garza, Alejandro J.; Bulik, Ireneusz W.; Alencar, Ana G. Sousa; Sun, Jianwei; Perdew, John P.; Scuseria, Gustavo E.

2016-04-01

Contrary to standard coupled cluster doubles (CCD) and Brueckner doubles (BD), singlet-paired analogues of CCD and BD (denoted here as CCD0 and BD0) do not break down when static correlation is present, but neglect substantial amounts of dynamic correlation. In fact, CCD0 and BD0 do not account for any contributions from multielectron excitations involving only same-spin electrons at all. We exploit this feature to add - without introducing double counting, self-interaction, or increase in cost - the missing correlation to these methods via meta-GGA (generalised gradient approximation) density functionals (Tao-Perdew-Staroverov-Scuseria and strongly constrained and appropriately normed). Furthermore, we improve upon these CCD0+DFT blends by invoking range separation: the short- and long-range correlations absent in CCD0/BD0 are evaluated with density functional theory and the direct random phase approximation, respectively. This corrects the description of long-range van der Waals forces. Comprehensive benchmarking shows that the combinations presented here are very accurate for weakly correlated systems, while also providing a reasonable description of strongly correlated problems without resorting to symmetry breaking.

Positively deflected anomaly mediation in the light of the Higgs boson discovery

NASA Astrophysics Data System (ADS)

Okada, Nobuchika; Tran, Hieu Minh

2013-02-01

Anomaly-mediated supersymmetry breaking (AMSB) is a well-known mechanism for flavor-blind transmission of supersymmetry breaking from the hidden sector to the visible sector. However, the pure AMSB scenario suffers from a serious drawback, namely, the tachyonic slepton problem, and needs to be extended. The so-called (positively) deflected AMSB is a simple extension to solve the problem and also provides us with the usual neutralino lightest superpartner as a good candidate for dark matter in the Universe. Motivated by the recent discovery of the Higgs boson at the Large Hadron Collider (LHC) experiments, we perform the parameter scan in the deflected AMSB scenario by taking into account a variety of phenomenological constraints, such as the dark matter relic density and the observed Higgs boson mass around 125-126 GeV. We identify the allowed parameter region and list benchmark mass spectra. We find that in most of the allowed parameter regions, the dark matter neutralino is Higgsino-like and its elastic scattering cross section with nuclei is within the future reach of the direct dark matter search experiments, while (colored) sparticles are quite heavy and their discovery at the LHC is challenging.

TRAC-PF1/MOD1 support calculations for the MIST/OTIS program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujita, R.K.; Knight, T.D.

1984-01-01

We are using the Transient Reactor Analysis Code (TRAC), specifically version TRAC-PF1/MOD1, to perform analyses in support of the MultiLoop Integral-System Test (MIST) and the Once-Through Integral-System (OTIS) experiment program. We have analyzed Geradrohr Dampferzeuger Anlage (GERDA) Test 1605AA to benchmark the TRAC-PF1/MOD1 code against phenomena expected to occur in a raised-loop B and W plant during a small-break loss-of-coolant accident (SBLOCA). These results show that the code can calculate both single- and two-phase natural circulation, flow interruption, boiler-condenser-mode (BCM) heat transfer, and primary-system refill in a B and W-type geometry with low-elevation auxiliary feedwater. 19 figures, 7 tables.

High coherence plane breaking packaging for superconducting qubits.

PubMed

Bronn, Nicholas T; Adiga, Vivekananda P; Olivadese, Salvatore B; Wu, Xian; Chow, Jerry M; Pappas, David P

2018-04-01

We demonstrate a pogo pin package for a superconducting quantum processor specifically designed with a nontrivial layout topology (e.g., a center qubit that cannot be accessed from the sides of the chip). Two experiments on two nominally identical superconducting quantum processors in pogo packages, which use commercially available parts and require modest machining tolerances, are performed at low temperature (10 mK) in a dilution refrigerator and both found to behave comparably to processors in standard planar packages with wirebonds where control and readout signals come in from the edges. Single- and two-qubit gate errors are also characterized via randomized benchmarking, exhibiting similar error rates as in standard packages, opening the possibility of integrating pogo pin packaging with extensible qubit architectures.

High coherence plane breaking packaging for superconducting qubits

NASA Astrophysics Data System (ADS)

Bronn, Nicholas T.; Adiga, Vivekananda P.; Olivadese, Salvatore B.; Wu, Xian; Chow, Jerry M.; Pappas, David P.

2018-04-01

We demonstrate a pogo pin package for a superconducting quantum processor specifically designed with a nontrivial layout topology (e.g., a center qubit that cannot be accessed from the sides of the chip). Two experiments on two nominally identical superconducting quantum processors in pogo packages, which use commercially available parts and require modest machining tolerances, are performed at low temperature (10 mK) in a dilution refrigerator and both found to behave comparably to processors in standard planar packages with wirebonds where control and readout signals come in from the edges. Single- and two-qubit gate errors are also characterized via randomized benchmarking, exhibiting similar error rates as in standard packages, opening the possibility of integrating pogo pin packaging with extensible qubit architectures.

Landscape of supersymmetric particle mass hierarchies and their signature space at the CERN Large Hadron Collider.

PubMed

Feldman, Daniel; Liu, Zuowei; Nath, Pran

2007-12-21

The minimal supersymmetric standard model with soft breaking has a large landscape of supersymmetric particle mass hierarchies. This number is reduced significantly in well-motivated scenarios such as minimal supergravity and alternatives. We carry out an analysis of the landscape for the first four lightest particles and identify at least 16 mass patterns, and provide benchmarks for each. We study the signature space for the patterns at the CERN Large Hadron Collider by analyzing the lepton+ (jet> or =2) + missing P{T} signals with 0, 1, 2, and 3 leptons. Correlations in missing P{T} are also analyzed. It is found that even with 10 fb{-1} of data a significant discrimination among patterns emerges.

New methods to benchmark simulations of accreting black holes systems against observations

NASA Astrophysics Data System (ADS)

Markoff, Sera; Chatterjee, Koushik; Liska, Matthew; Tchekhovskoy, Alexander; Hesp, Casper; Ceccobello, Chiara; Russell, Thomas

2017-08-01

The field of black hole accretion has been significantly advanced by the use of complex ideal general relativistic magnetohydrodynamics (GRMHD) codes, now capable of simulating scales from the event horizon out to ~10^5 gravitational radii at high resolution. The challenge remains how to test these simulations against data, because the self-consistent treatment of radiation is still in its early days, and is complicated by dependence on non-ideal/microphysical processes not yet included in the codes. On the other extreme, a variety of phenomenological models (disk, corona, jet, wind) can well-describe spectra or variability signatures in a particular waveband, although often not both. To bring these two methodologies together, we need robust observational “benchmarks” that can be identified and studied in simulations. I will focus on one example of such a benchmark, from recent observational campaigns on black holes across the mass scale: the jet break. I will describe new work attempting to understand what drives this feature by searching for regions that share similar trends in terms of dependence on accretion power or magnetisation. Such methods can allow early tests of simulation assumptions and help pinpoint which regions will dominate the light production, well before full radiative processes are incorporated, and will help guide the interpretation of, e.g. Event Horizon Telescope data.

High-Precision Half-Life Measurement for the Superallowed β+ Emitter Alm26

NASA Astrophysics Data System (ADS)

Finlay, P.; Ettenauer, S.; Ball, G. C.; Leslie, J. R.; Svensson, C. E.; Andreoiu, C.; Austin, R. A. E.; Bandyopadhyay, D.; Cross, D. S.; Demand, G.; Djongolov, M.; Garrett, P. E.; Green, K. L.; Grinyer, G. F.; Hackman, G.; Leach, K. G.; Pearson, C. J.; Phillips, A. A.; Sumithrarachchi, C. S.; Triambak, S.; Williams, S. J.

2011-01-01

A high-precision half-life measurement for the superallowed β+ emitter Alm26 was performed at the TRIUMF-ISAC radioactive ion beam facility yielding T1/2=6346.54±0.46stat±0.60systms, consistent with, but 2.5 times more precise than, the previous world average. The Alm26 half-life and ft value, 3037.53(61) s, are now the most precisely determined for any superallowed β decay. Combined with recent theoretical corrections for isospin-symmetry-breaking and radiative effects, the corrected Ft value for Alm26, 3073.0(12) s, sets a new benchmark for the high-precision superallowed Fermi β-decay studies used to test the conserved vector current hypothesis and determine the Vud element of the Cabibbo-Kobayashi-Maskawa quark mixing matrix.

A socio-technical approach for improving a Brazilian shoe manufacturing system.

PubMed

Renner, J S; de M Guimarães, L B; de Oliveira, P A B

2012-01-01

This article presents a macroergonomic intervention in a footwear company in Rio Grande do Sul, Brazil, to improve both the quality of life of the employees and productivity by optimizing the traditional Taylor/Ford work organization. Multi-functionality and team working were implemented as means of making tasks more flexible and richer and the working hours were changed. The results showed a reduction in human and material resource costs and a consequent improvement in health and workers quality of life. Although middle managerial staff displayed strong resistance to the project and to breaking traditional production paradigms, the socio-technical system has been implemented throughout the plant and is expected to end up becoming the benchmark for other companies in the sector. Macro-ergonomics, footwear industry, organization work.

Mitigating wildland fire hazard using complex network centrality measures

NASA Astrophysics Data System (ADS)

Russo, Lucia; Russo, Paola; Siettos, Constantinos I.

2016-12-01

We show how to distribute firebreaks in heterogeneous forest landscapes in the presence of strong wind using complex network centrality measures. The proposed framework is essentially a two-tire one: at the inner part a state-of- the-art Cellular Automata model is used to compute the weights of the underlying lattice network while at the outer part the allocation of the fire breaks is scheduled in terms of a hierarchy of centralities which influence the most the spread of fire. For illustration purposes we applied the proposed framework to a real-case wildfire that broke up in Spetses Island, Greece in 1990. We evaluate the scheme against the benchmark of random allocation of firebreaks under the weather conditions of the real incident i.e. in the presence of relatively strong winds.

Learning to forget: continual prediction with LSTM.

PubMed

Gers, F A; Schmidhuber, J; Cummins, F

2000-10-01

Long short-term memory (LSTM; Hochreiter & Schmidhuber, 1997) can solve numerous tasks not solvable by previous learning algorithms for recurrent neural networks (RNNs). We identify a weakness of LSTM networks processing continual input streams that are not a priori segmented into subsequences with explicitly marked ends at which the network's internal state could be reset. Without resets, the state may grow indefinitely and eventually cause the network to break down. Our remedy is a novel, adaptive "forget gate" that enables an LSTM cell to learn to reset itself at appropriate times, thus releasing internal resources. We review illustrative benchmark problems on which standard LSTM outperforms other RNN algorithms. All algorithms (including LSTM) fail to solve continual versions of these problems. LSTM with forget gates, however, easily solves them, and in an elegant way.

Exploratory X-ray Monitoring of z>4 Radio-Quiet Quasars

NASA Astrophysics Data System (ADS)

Shemmer, Ohad

2017-09-01

We propose to extend our exploratory X-ray monitoring project of some of the most distant radio-quiet quasars by obtaining one snapshot observation per Cycle for each of four sources at z>4. Combining these observations with six available X-ray epochs per source will provide basic temporal information over rest-frame timescales of 3-5 yr. We are supporting this project with Swift monitoring of luminous radio-quiet quasars at z=1.3-2.7 to break the L-z degeneracy and test evolutionary scenarios of the central engine in active galactic nuclei. Our ultimate goal is to provide a basic assessment of the X-ray variability properties of luminous quasars at the highest accessible redshifts that will serve as the benchmark for X-ray variability studies of such sources with future X-ray missions.

Precise determination of lattice phase shifts and mixing angles

DOE PAGES

Lu, Bing -Nan; Lähde, Timo A.; Lee, Dean; ...

2016-07-09

Here, we introduce a general and accurate method for determining lattice phase shifts and mixing angles, which is applicable to arbitrary, non-cubic lattices. Our method combines angular momentum projection, spherical wall boundaries and an adjustable auxiliary potential. This allows us to construct radial lattice wave functions and to determine phase shifts at arbitrary energies. For coupled partial waves, we use a complex-valued auxiliary potential that breaks time-reversal invariance. We benchmark our method using a system of two spin-1/2 particles interacting through a finite-range potential with a strong tensor component. We are able to extract phase shifts and mixing angles formore » all angular momenta and energies, with precision greater than that of extant methods. We discuss a wide range of applications from nuclear lattice simulations to optical lattice experiments.« less

Performance Benchmarking of tsunami-HySEA for NTHMP Inundation Mapping Activities

NASA Astrophysics Data System (ADS)

González Vida, Jose M.; Castro, Manuel J.; Ortega Acosta, Sergio; Macías, Jorge; Millán, Alejandro

2016-04-01

According to the 2006 USA Tsunami Warning and Education Act, the tsunami inundation models used in the National Tsunami Hazard Mitigation Program (NTHMP) projects must be validated against some existing standard problems (see [OAR-PMEL-135], [Proceedings of the 2011 NTHMP Model Benchmarking Workshop]). These Benchmark Problems (BPs) cover different tsunami processes related to the inundation stage that the models must meet to achieve the NTHMP Mapping and Modeling Subcommittee (MMS) approval. Tsunami-HySEA solves the two-dimensional shallow-water system using a high-order path-conservative finite volume method. Values of h, qx and qy in each grid cell represent cell averages of the water depth and momentum components. The numerical scheme is conservative for both mass and momentum in flat bathymetries, and, in general, is mass preserving for arbitrary bathymetries. Tsunami-HySEA implements a PVM-type method that uses the fastest and the slowest wave speeds, similar to HLL method (see [Castro et al, 2012]). A general overview of the derivation of the high order methods is performed in [Castro et al, 2009]. For very big domains, Tsunami-HySEA also implements a two-step scheme similar to leap-frog for the propagation step and a second-order TVD-WAF flux-limiter scheme described in [de la Asunción et al, 2013] for the inundation step. Here, we present the results obtained by the model tsunami-HySEA against the proposed BPs. BP1: Solitary wave on a simple beach (non-breaking - analytic experiment). BP4: Solitary wave on a simple beach (breaking - laboratory experiment). BP6: Solitary wave on a conical island (laboratory experiment). BP7 - Runup on Monai Valley beach (laboratory experiment) and BP9: Okushiri Island tsunami (field experiment). The analysis and results of Tsunami-HySEA model are presented, concluding that the model meets the required objectives for all the BP proposed. References - Castro M.J., E.D. Fernández, A.M. Ferreiro, A. García, C. Parés (2009). High order extension of Roe schemes for two dimensional nonconservative hyperbolic systems. J. Sci. Comput. 39(1), 67-114. - Castro M.J., E.D. Fernández-Nieto (2012). A class of computationally fast first order finite volume solvers: PVM methods. SIAM J. Sci. Comput. 34, A2173-2196. - de la Asunción M., M.J. Castro, E.D. Fernández-Nieto, J.M. Mantas, et al. Efficient GPU implementation of a two waves TVD-WAF method for the two-dimensional one layer shallow water system on structured meshes (2013). Computers & Fluids 80, 441-452. - OAR PMEL-135. Synolakis, C.E., E.N. Bernard, V.V. Titov, U. Kânoǧlu, and F.I. González (2007). Standards, criteria, and procedures for NOAA evaluation of tsunami numerical models. NOAA Tech. Memo. NOAA/Pacific Marine Environmental Laboratory, Seattle, WA, 55 pp. - Proceedings and results of the 2011 NTHMP Model Benchmarking Workshop. NOAA Special Report. July 2012. Acknowledgements This research has been partially supported by the Junta de Andalucía research project TESELA (P11-RNM7069), the Spanish Government Research project DAIFLUID (MTM2012-38383-C02-01) and the Unit of Numerical Methods (UNM) of the Research Support Central Services (SCAI) of the University of Málaga.

Adaptive finite volume methods with well-balanced Riemann solvers for modeling floods in rugged terrain: Application to the Malpasset dam-break flood (France, 1959)

USGS Publications Warehouse

George, D.L.

2011-01-01

The simulation of advancing flood waves over rugged topography, by solving the shallow-water equations with well-balanced high-resolution finite volume methods and block-structured dynamic adaptive mesh refinement (AMR), is described and validated in this paper. The efficiency of block-structured AMR makes large-scale problems tractable, and allows the use of accurate and stable methods developed for solving general hyperbolic problems on quadrilateral grids. Features indicative of flooding in rugged terrain, such as advancing wet-dry fronts and non-stationary steady states due to balanced source terms from variable topography, present unique challenges and require modifications such as special Riemann solvers. A well-balanced Riemann solver for inundation and general (non-stationary) flow over topography is tested in this context. The difficulties of modeling floods in rugged terrain, and the rationale for and efficacy of using AMR and well-balanced methods, are presented. The algorithms are validated by simulating the Malpasset dam-break flood (France, 1959), which has served as a benchmark problem previously. Historical field data, laboratory model data and other numerical simulation results (computed on static fitted meshes) are shown for comparison. The methods are implemented in GEOCLAW, a subset of the open-source CLAWPACK software. All the software is freely available at. Published in 2010 by John Wiley & Sons, Ltd.

High-Precision Half-Life and Branching Ratio Measurements for the Superallowed β+ Emitter 26Alm

NASA Astrophysics Data System (ADS)

Finlay, P.; Svensson, C. E.; Demand, G. A.; Garrett, P. E.; Green, K. L.; Leach, K. G.; Phillips, A. A.; Rand, E. T.; Ball, G.; Bandyopadhyay, D.; Djongolov, M.; Ettenauer, S.; Hackman, G.; Pearson, C. J.; Leslie, J. R.; Andreoiu, C.; Cross, D.; Austin, R. A. E.; Grinyer, G. F.; Sumithrarachchi, C. S.; Williams, S. J.; Triambak, S.

2013-03-01

High-precision half-life and branching-ratio measurements for the superallowed β+ emitter 26Alm were performed at the TRIUMF-ISAC radioactive ion beam facility. An upper limit of ≤ 15 ppm at 90% C.L. was determined for the sum of all possible non-analogue β+/EC decay branches of 26Alm, yielding a superallowed branching ratio of 100.0000+0-0.0015%. A value of T1/2 = 6:34654(76) s was determined for the 26Alm half-life which is consistent with, but 2.5 times more precise than, the previous world average. Combining these results with world-average measurements yields an ft value of 3037.58(60) s, the most precisely determined for any superallowed emitting nucleus to date. This high-precision ft value for 26Alm provides a new benchmark to refine theoretical models of isospin-symmetry-breaking effects in superallowed β decays.

Prizes for innovation of new medicines and vaccines.

PubMed

Love, James; Hubbard, Tim

2009-01-01

This article argues that prizes can help stimulate medical innovation, control costs and ensure greater access to new medicines and vaccines. The authors explore four increasingly ambitious prize options to reward medical innovation, each addressing flaws in the current patent system. The first option promotes innovation through a large prize fund linked to the impact on health outcomes; the second option rewards the sharing of knowledge, data, and technology with open source dividends; the third option awards prizes for interim benchmarks and discrete technical problems; and the final option removes the exclusive right to use patented inventions in upstream research in favor of prizes. The authors conclude that a system of prizes to reward drug development would break the link between R&D incentives and product prices, and that such a reform is needed to improve innovation and access to new medicines and vaccines.

Profitability Analysis of Soybean Oil Processes.

PubMed

Cheng, Ming-Hsun; Rosentrater, Kurt A

2017-10-07

Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV), break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP), is profitable when the capacity is larger than 17 million kg of annual oil production.

Profitability Analysis of Soybean Oil Processes

PubMed Central

2017-01-01

Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV), break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP), is profitable when the capacity is larger than 17 million kg of annual oil production. PMID:28991168

Demography of human supercentenarians.

PubMed

Coles, L Stephen

2004-06-01

An international committee of demographers has created a carefully documented list of worldwide living supercentenarians (> or =110 years old) that has been published by the Los Angeles Gerontology Research Group on its web site and updated on a weekly basis for the past 6 years [see "snapshot" for the year 2003 in the Appendix]. What can be learned by studying this distinguished group of individuals? Also, what are the implications for understanding the fundamental biological limits to human longevity and maximum life span? Our conclusion: Although everyone agrees that average life expectancy has systematically advanced linearly over the last century, it is not realistic to expect that this pace can continue indefinitely. Our data suggest that, without the invention of some new unknown form of medical breakthrough, the Guinness Book of World Records benchmark established by French woman Jeanne Calment of 122 years, set back in 1997, will be exceedingly difficult to break in our lifetime.

Patch planting of hard spin-glass problems: Getting ready for the next generation of optimization approaches

NASA Astrophysics Data System (ADS)

Wang, Wenlong; Mandrà, Salvatore; Katzgraber, Helmut

We propose a patch planting heuristic that allows us to create arbitrarily-large Ising spin-glass instances on any topology and with any type of disorder, and where the exact ground-state energy of the problem is known by construction. By breaking up the problem into patches that can be treated either with exact or heuristic solvers, we can reconstruct the optimum of the original, considerably larger, problem. The scaling of the computational complexity of these instances with various patch numbers and sizes is investigated and compared with random instances using population annealing Monte Carlo and quantum annealing on the D-Wave 2X quantum annealer. The method can be useful for benchmarking of novel computing technologies and algorithms. NSF-DMR-1208046 and the Office of the Director of National Intelligence (ODNI), Intelligence Advanced Research Projects Activity (IARPA), via MIT Lincoln Laboratory Air Force Contract No. FA8721-05-C-0002.

High-Precision Half-Life Measurement for the Superallowed {beta}{sup +} Emitter {sup 26}Al{sup m}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finlay, P.; Svensson, C. E.; Green, K. L.

2011-01-21

A high-precision half-life measurement for the superallowed {beta}{sup +} emitter {sup 26}Al{sup m} was performed at the TRIUMF-ISAC radioactive ion beam facility yielding T{sub 1/2}=6346.54{+-}0.46{sub stat{+-}}0.60{sub syst} ms, consistent with, but 2.5 times more precise than, the previous world average. The {sup 26}Al{sup m} half-life and ft value, 3037.53(61) s, are now the most precisely determined for any superallowed {beta} decay. Combined with recent theoretical corrections for isospin-symmetry-breaking and radiative effects, the corrected Ft value for {sup 26}Al{sup m}, 3073.0(12) s, sets a new benchmark for the high-precision superallowed Fermi {beta}-decay studies used to test the conserved vector current hypothesismore » and determine the V{sub ud} element of the Cabibbo-Kobayashi-Maskawa quark mixing matrix.« less

Once-through integral system (OTIS): Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gloudemans, J R

1986-09-01

A scaled experimental facility, designated the once-through integral system (OTIS), was used to acquire post-small break loss-of-coolant accident (SBLOCA) data for benchmarking system codes. OTIS was also used to investigate the application of the Abnormal Transient Operating Guidelines (ATOG) used in the Babcock and Wilcox (B and W) designed nuclear steam supply system (NSSS) during the course of an SBLOCA. OTIS was a single-loop facility with a plant to model power scale factor of 1686. OTIS maintained the key elevations, approximate component volumes, and loop flow resistances, and simulated the major component phenomena of a B and W raised-loop nuclearmore » plant. A test matrix consisting of 15 tests divided into four categories was performed. The largest group contained 10 tests and was defined to parametrically obtain an extensive set of plant-typical experimental data for code benchmarking. Parameters such as leak size, leak location, and high-pressure injection (HPI) shut-off head were individually varied. The remaining categories were specified to study the impact of the ATOGs (2 tests), to note the effect of guard heater operation on observed phenomena (2 tests), and to provide a data set for comparison with previous test experience (1 test). A summary of the test results and a detailed discussion of Test 220100 is presented. Test 220100 was the nominal or reference test for the parametric studies. This test was performed with a scaled 10-cm/sup 2/ leak located in the cold leg suction piping.« less

Dynamics and breakup of a contracting liquid filament

NASA Astrophysics Data System (ADS)

Notz, Patrick K.; Basaran, Osman A.

2004-08-01

Contraction of a filament of an incompressible Newtonian liquid in a passive ambient fluid is studied computationally to provide insights into the dynamics of satellite drops created during drop formation. This free boundary problem, which is composed of the Navier Stokes system and the associated initial and boundary conditions that govern the evolution in time of the filament shape and the velocity and pressure fields within it, is solved by the method of lines incorporating the finite element method for spatial discretization. The finite element algorithm developed here utilizes an adaptive elliptic mesh generation technique that is capable of tracking the dynamics of the filament up to the incipience of pinch-off without the use of remeshing. The correctness of the algorithm is verified by demonstrating that its predictions accord with (a) previously published results of Basaran (1992) on the analysis of finite-amplitude oscillations of viscous drops, (b) simulations of the dynamics of contracting filaments carried out with the well-benchmarked algorithm of Wilkes et al. (1999), and (c) scaling laws governing interface rupture and transitions that can occur from one scaling law to another as pinch-off is approached. In dimensionless form, just two parameters govern the problem: the dimensionless half-length L_o and the Ohnesorge number Oh which measures the relative importance of viscous force to capillary force. Regions of the parameter space are identified where filaments (a) contract to a sphere without breaking into multiple droplets, (b) break via the so-called endpinching mechanism where daughter drops pinch-off from the ends of the main filament, and (c) break after undergoing a series of complex oscillations. Predictions made with the new algorithm are also compared to those made with a model based on the slender-jet approximation. A region of the parameter space is found where the slender-jet approximation fares poorly, and its cause is elucidated by examination of the vorticity dynamics and flow fields within contracting filaments.

An analytically solvable three-body break-up model problem in hyperspherical coordinates

NASA Astrophysics Data System (ADS)

Ancarani, L. U.; Gasaneo, G.; Mitnik, D. M.

2012-10-01

An analytically solvable S-wave model for three particles break-up processes is presented. The scattering process is represented by a non-homogeneous Coulombic Schrödinger equation where the driven term is given by a Coulomb-like interaction multiplied by the product of a continuum wave function and a bound state in the particles coordinates. The closed form solution is derived in hyperspherical coordinates leading to an analytic expression for the associated scattering transition amplitude. The proposed scattering model contains most of the difficulties encountered in real three-body scattering problem, e.g., non-separability in the electrons' spherical coordinates and Coulombic asymptotic behavior. Since the coordinates' coupling is completely different, the model provides an alternative test to that given by the Temkin-Poet model. The knowledge of the analytic solution provides an interesting benchmark to test numerical methods dealing with the double continuum, in particular in the asymptotic regions. An hyperspherical Sturmian approach recently developed for three-body collisional problems is used to reproduce to high accuracy the analytical results. In addition to this, we generalized the model generating an approximate wave function possessing the correct radial asymptotic behavior corresponding to an S-wave three-body Coulomb problem. The model allows us to explore the typical structure of the solution of a three-body driven equation, to identify three regions (the driven, the Coulombic and the asymptotic), and to analyze how far one has to go to extract the transition amplitude.

A CONNECTION BETWEEN PLASMA CONDITIONS NEAR BLACK HOLE EVENT HORIZONS AND OUTFLOW PROPERTIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koljonen, K. I. I.; Russell, D. M.; Bernardini, F.

Accreting black holes are responsible for producing the fastest, most powerful outflows of matter in the universe. The formation process of powerful jets close to black holes is poorly understood, and the conditions leading to jet formation are currently hotly debated. In this paper, we report an unambiguous empirical correlation between the properties of the plasma close to the black hole and the particle acceleration properties within jets launched from the central regions of accreting stellar-mass and supermassive black holes. In these sources the emission of the plasma near the black hole is characterized by a power law at X-raymore » energies during times when the jets are produced. We find that the photon index of this power law, which gives information on the underlying particle distribution, correlates with the characteristic break frequency in the jet spectrum, which is dependent on magnetohydrodynamical processes in the outflow. The observed range in break frequencies varies by five orders of magnitude in sources that span nine orders of magnitude in black hole mass, revealing a similarity of jet properties over a large range of black hole masses powering these jets. This correlation demonstrates that the internal properties of the jet rely most critically on the conditions of the plasma close to the black hole, rather than other parameters such as the black hole mass or spin, and will provide a benchmark that should be reproduced by the jet formation models.« less

New indicators based on personnel cost for management efficiency in a hospital.

PubMed

Nakagawa, Yoshiaki; Yoshihara, Hiroyuki; Nakagawa, Yoshinobu

2011-08-01

A simple and fair benchmarking system or financial indicators for use on the clinical department level have been lacking to evaluate the management efficiency and activity of each clinical department or division of a hospital. New financial indicators have therefore been developed based on personnel costs. Indicator 1: The ratio of marginal profit after personnel cost per personnel cost (RMP). Indicator 2: The ratio of investment (=indirect cost) per personnel cost (RIP). The difference between RMP and RIP demonstrates the operation profit in US Dollars for personnel cost (OPP). A turning point in profitability similar to the break-even point (BEP) and break-even ratio (BER) could be also defined by the combination of the RMP and RIP. The merits of these two indicators are not only the ability to indicate the relationship between the medical profit and the investments in the hospital, but also the capability to demonstrate such indicators as BEP, BER and OPP on a single graph. The two indicators were applied to the hospitals in the National Hospital Organization and to the clinical department in one hospital. Using these two indicators, it was possible to evaluate the management efficiency and medical activity not only in the whole hospital but also in each department and DPC/DRG group. This will be of use to a manager of a hospital in checking the management efficiency of his/her hospital despite the variations among hospitals, departments and divisions.

Benchmarking reference services: step by step.

PubMed

Buchanan, H S; Marshall, J G

1996-01-01

This article is a companion to an introductory article on benchmarking published in an earlier issue of Medical Reference Services Quarterly. Librarians interested in benchmarking often ask the following questions: How do I determine what to benchmark; how do I form a benchmarking team; how do I identify benchmarking partners; what's the best way to collect and analyze benchmarking information; and what will I do with the data? Careful planning is a critical success factor of any benchmarking project, and these questions must be answered before embarking on a benchmarking study. This article summarizes the steps necessary to conduct benchmarking research. Relevant examples of each benchmarking step are provided.

Study on homogenization of synthetic GNSS-retrieved IWV time series and its impact on trend estimates with autoregressive noise

NASA Astrophysics Data System (ADS)

Klos, Anna; Pottiaux, Eric; Van Malderen, Roeland; Bock, Olivier; Bogusz, Janusz

2017-04-01

A synthetic benchmark dataset of Integrated Water Vapour (IWV) was created within the activity of "Data homogenisation" of sub-working group WG3 of COST ES1206 Action. The benchmark dataset was created basing on the analysis of IWV differences retrieved by Global Positioning System (GPS) International GNSS Service (IGS) stations using European Centre for Medium-Range Weather Forecats (ECMWF) reanalysis data (ERA-Interim). Having analysed a set of 120 series of IWV differences (ERAI-GPS) derived for IGS stations, we delivered parameters of a number of gaps and breaks for every certain station. Moreover, we estimated values of trends, significant seasonalities and character of residuals when deterministic model was removed. We tested five different noise models and found that a combination of white and autoregressive processes of first order describes the stochastic part with a good accuracy. Basing on this analysis, we performed Monte Carlo simulations of 25 years long data with two different types of noise: white as well as combination of white and autoregressive processes. We also added few strictly defined offsets, creating three variants of synthetic dataset: easy, less-complicated and fully-complicated. The 'Easy' dataset included seasonal signals (annual, semi-annual, 3 and 4 months if present for a particular station), offsets and white noise. The 'Less-complicated' dataset included above-mentioned, as well as the combination of white and first order autoregressive processes (AR(1)+WH). The 'Fully-complicated' dataset included, beyond above, a trend and gaps. In this research, we show the impact of manual homogenisation on the estimates of trend and its error. We also cross-compare the results for three above-mentioned datasets, as the synthetized noise type might have a significant influence on manual homogenisation. Therefore, it might mostly affect the values of trend and their uncertainties when inappropriately handled. In a future, the synthetic dataset we present is going to be used as a benchmark to test various statistical tools in terms of homogenisation task.

Limitations of Community College Benchmarking and Benchmarks

ERIC Educational Resources Information Center

Bers, Trudy H.

2006-01-01

This chapter distinguishes between benchmarks and benchmarking, describes a number of data and cultural limitations to benchmarking projects, and suggests that external demands for accountability are the dominant reason for growing interest in benchmarking among community colleges.

Benchmarking specialty hospitals, a scoping review on theory and practice.

PubMed

Wind, A; van Harten, W H

2017-04-04

Although benchmarking may improve hospital processes, research on this subject is limited. The aim of this study was to provide an overview of publications on benchmarking in specialty hospitals and a description of study characteristics. We searched PubMed and EMBASE for articles published in English in the last 10 years. Eligible articles described a project stating benchmarking as its objective and involving a specialty hospital or specific patient category; or those dealing with the methodology or evaluation of benchmarking. Of 1,817 articles identified in total, 24 were included in the study. Articles were categorized into: pathway benchmarking, institutional benchmarking, articles on benchmark methodology or -evaluation and benchmarking using a patient registry. There was a large degree of variability:(1) study designs were mostly descriptive and retrospective; (2) not all studies generated and showed data in sufficient detail; and (3) there was variety in whether a benchmarking model was just described or if quality improvement as a consequence of the benchmark was reported upon. Most of the studies that described a benchmark model described the use of benchmarking partners from the same industry category, sometimes from all over the world. Benchmarking seems to be more developed in eye hospitals, emergency departments and oncology specialty hospitals. Some studies showed promising improvement effects. However, the majority of the articles lacked a structured design, and did not report on benchmark outcomes. In order to evaluate the effectiveness of benchmarking to improve quality in specialty hospitals, robust and structured designs are needed including a follow up to check whether the benchmark study has led to improvements.

All inclusive benchmarking.

PubMed

Ellis, Judith

2006-07-01

The aim of this article is to review published descriptions of benchmarking activity and synthesize benchmarking principles to encourage the acceptance and use of Essence of Care as a new benchmarking approach to continuous quality improvement, and to promote its acceptance as an integral and effective part of benchmarking activity in health services. The Essence of Care, was launched by the Department of Health in England in 2001 to provide a benchmarking tool kit to support continuous improvement in the quality of fundamental aspects of health care, for example, privacy and dignity, nutrition and hygiene. The tool kit is now being effectively used by some frontline staff. However, use is inconsistent, with the value of the tool kit, or the support clinical practice benchmarking requires to be effective, not always recognized or provided by National Health Service managers, who are absorbed with the use of quantitative benchmarking approaches and measurability of comparative performance data. This review of published benchmarking literature, was obtained through an ever-narrowing search strategy commencing from benchmarking within quality improvement literature through to benchmarking activity in health services and including access to not only published examples of benchmarking approaches and models used but the actual consideration of web-based benchmarking data. This supported identification of how benchmarking approaches have developed and been used, remaining true to the basic benchmarking principles of continuous improvement through comparison and sharing (Camp 1989). Descriptions of models and exemplars of quantitative and specifically performance benchmarking activity in industry abound (Camp 1998), with far fewer examples of more qualitative and process benchmarking approaches in use in the public services and then applied to the health service (Bullivant 1998). The literature is also in the main descriptive in its support of the effectiveness of benchmarking activity and although this does not seem to have restricted its popularity in quantitative activity, reticence about the value of the more qualitative approaches, for example Essence of Care, needs to be overcome in order to improve the quality of patient care and experiences. The perceived immeasurability and subjectivity of Essence of Care and clinical practice benchmarks means that these benchmarking approaches are not always accepted or supported by health service organizations as valid benchmarking activity. In conclusion, Essence of Care benchmarking is a sophisticated clinical practice benchmarking approach which needs to be accepted as an integral part of health service benchmarking activity to support improvement in the quality of patient care and experiences.

Radiation breakage of DNA: a model based on random-walk chromatin structure

NASA Technical Reports Server (NTRS)

Ponomarev, A. L.; Sachs, R. K.

2001-01-01

Monte Carlo computer software, called DNAbreak, has recently been developed to analyze observed non-random clustering of DNA double strand breaks in chromatin after exposure to densely ionizing radiation. The software models coarse-grained configurations of chromatin and radiation tracks, small-scale details being suppressed in order to obtain statistical results for larger scales, up to the size of a whole chromosome. We here give an analytic counterpart of the numerical model, useful for benchmarks, for elucidating the numerical results, for analyzing the assumptions of a more general but less mechanistic "randomly-located-clusters" formalism, and, potentially, for speeding up the calculations. The equations characterize multi-track DNA fragment-size distributions in terms of one-track action; an important step in extrapolating high-dose laboratory results to the much lower doses of main interest in environmental or occupational risk estimation. The approach can utilize the experimental information on DNA fragment-size distributions to draw inferences about large-scale chromatin geometry during cell-cycle interphase.

Spin-valley locking in the normal state of a transition-metal dichalcogenide superconductor.

PubMed

Bawden, L; Cooil, S P; Mazzola, F; Riley, J M; Collins-McIntyre, L J; Sunko, V; Hunvik, K W B; Leandersson, M; Polley, C M; Balasubramanian, T; Kim, T K; Hoesch, M; Wells, J W; Balakrishnan, G; Bahramy, M S; King, P D C

2016-05-23

Metallic transition-metal dichalcogenides (TMDCs) are benchmark systems for studying and controlling intertwined electronic orders in solids, with superconductivity developing from a charge-density wave state. The interplay between such phases is thought to play a critical role in the unconventional superconductivity of cuprates, Fe-based and heavy-fermion systems, yet even for the more moderately-correlated TMDCs, their nature and origins have proved controversial. Here, we study a prototypical example, 2H-NbSe2, by spin- and angle-resolved photoemission and first-principles theory. We find that the normal state, from which its hallmark collective phases emerge, is characterized by quasiparticles whose spin is locked to their valley pseudospin. This results from a combination of strong spin-orbit interactions and local inversion symmetry breaking, while interlayer coupling further drives a rich three-dimensional momentum dependence of the underlying Fermi-surface spin texture. These findings necessitate a re-investigation of the nature of charge order and superconducting pairing in NbSe2 and related TMDCs.

ICCD: interactive continuous collision detection between deformable models using connectivity-based culling.

PubMed

Tang, Min; Curtis, Sean; Yoon, Sung-Eui; Manocha, Dinesh

2009-01-01

We present an interactive algorithm for continuous collision detection between deformable models. We introduce multiple techniques to improve the culling efficiency and the overall performance of continuous collision detection. First, we present a novel formulation for continuous normal cones and use these normal cones to efficiently cull large regions of the mesh as part of self-collision tests. Second, we introduce the concept of "procedural representative triangles" to remove all redundant elementary tests between nonadjacent triangles. Finally, we exploit the mesh connectivity and introduce the concept of "orphan sets" to eliminate redundant elementary tests between adjacent triangle primitives. In practice, we can reduce the number of elementary tests by two orders of magnitude. These culling techniques have been combined with bounding volume hierarchies and can result in one order of magnitude performance improvement as compared to prior collision detection algorithms for deformable models. We highlight the performance of our algorithm on several benchmarks, including cloth simulations, N-body simulations, and breaking objects.

Theoretical development and first-principles analysis of strongly correlated systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chen

A variety of quantum many-body methods have been developed for studying the strongly correlated electron systems. We have also proposed a computationally efficient and accurate approach, named the correlation matrix renormalization (CMR) method, to address the challenges. The initial implementation of the CMR method is designed for molecules which have theoretical advantages, including small size of system, manifest mechanism and strongly correlation effect such as bond breaking process. The theoretic development and benchmark tests of the CMR method are included in this thesis. Meanwhile, ground state total energy is the most important property of electronic calculations. We also investigated anmore » alternative approach to calculate the total energy, and extended this method for magnetic anisotropy energy (MAE) of ferromagnetic materials. In addition, another theoretical tool, dynamical mean- field theory (DMFT) on top of the DFT , has also been used in electronic structure calculations for an Iridium oxide to study the phase transition, which results from an interplay of the d electrons' internal degrees of freedom.« less

Cosmic archaeology with gravitational waves from cosmic strings

NASA Astrophysics Data System (ADS)

Cui, Yanou; Lewicki, Marek; Morrissey, David E.; Wells, James D.

2018-06-01

Cosmic strings are generic cosmological predictions of many extensions of the standard model of particle physics, such as a U (1 )' symmetry-breaking phase transition in the early Universe or remnants of superstring theory. Unlike other topological defects, cosmic strings can reach a scaling regime that maintains a small fixed fraction of the total energy density of the Universe from a very early epoch until today. If present, they will oscillate and generate gravitational waves with a frequency spectrum that imprints the dominant sources of total cosmic energy density throughout the history of the Universe. We demonstrate that current and future gravitational wave detectors, such as LIGO and LISA, could be capable of measuring the frequency spectrum of gravitational waves from cosmic strings and discerning the energy composition of the Universe at times well before primordial nucleosynthesis and the cosmic microwave background where standard cosmology has yet to be tested. This work establishes a benchmark case that gravitational waves may provide an unprecedented, powerful tool for probing the evolutionary history of the very early Universe.

Multi-scale simulations of droplets in generic time-dependent flows

NASA Astrophysics Data System (ADS)

Milan, Felix; Biferale, Luca; Sbragaglia, Mauro; Toschi, Federico

2017-11-01

We study the deformation and dynamics of droplets in time-dependent flows using a diffuse interface model for two immiscible fluids. The numerical simulations are at first benchmarked against analytical results of steady droplet deformation, and further extended to the more interesting case of time-dependent flows. The results of these time-dependent numerical simulations are compared against analytical models available in the literature, which assume the droplet shape to be an ellipsoid at all times, with time-dependent major and minor axis. In particular we investigate the time-dependent deformation of a confined droplet in an oscillating Couette flow for the entire capillary range until droplet break-up. In this way these multi component simulations prove to be a useful tool to establish from ``first principles'' the dynamics of droplets in complex flows involving multiple scales. European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie Grant Agreement No 642069. & European Research Council under the European Community's Seventh Framework Program, ERC Grant Agreement No 339032.

Discovering Technicolor

NASA Astrophysics Data System (ADS)

Andersen, J. R.; Antipin, O.; Azuelos, G.; Del Debbio, L.; Del Nobile, E.; Di Chiara, S.; Hapola, T.; Järvinen, M.; Lowdon, P. J.; Maravin, Y.; Masina, I.; Nardecchia, M.; Pica, C.; Sannino, F.

2011-09-01

We provide a pedagogical introduction to extensions of the Standard Model in which the Higgs is composite. These extensions are known as models of dynamical electroweak symmetry breaking or, in brief, Technicolor. Material covered includes: motivations for Technicolor, the construction of underlying gauge theories leading to minimal models of Technicolor, the comparison with electroweak precision data, the low-energy effective theory, the spectrum of the states common to most of the Technicolor models, the decays of the composite particles and the experimental signals at the Large Hadron Collider. The level of the presentation is aimed at readers familiar with the Standard Model but who have little or no prior exposure to Technicolor. Several extensions of the Standard Model featuring a composite Higgs can be reduced to the effective Lagrangian introduced in the text. We establish the relevant experimental benchmarks for Vanilla, Running, Walking, and Custodial Technicolor, and a natural fourth family of leptons, by laying out the framework to discover these models at the Large Hadron Collider.

Analytical derivatives of the individual state energies in ensemble density functional theory method. I. General formalism

DOE PAGES

Filatov, Michael; Liu, Fang; Martínez, Todd J.

2017-07-21

The state-averaged (SA) spin restricted ensemble referenced Kohn-Sham (REKS) method and its state interaction (SI) extension, SI-SA-REKS, enable one to describe correctly the shape of the ground and excited potential energy surfaces of molecules undergoing bond breaking/bond formation reactions including features such as conical intersections crucial for theoretical modeling of non-adiabatic reactions. Until recently, application of the SA-REKS and SI-SA-REKS methods to modeling the dynamics of such reactions was obstructed due to the lack of the analytical energy derivatives. Here, the analytical derivatives of the individual SA-REKS and SI-SA-REKS energies are derived. The final analytic gradient expressions are formulated entirelymore » in terms of traces of matrix products and are presented in the form convenient for implementation in the traditional quantum chemical codes employing basis set expansions of the molecular orbitals. Finally, we will describe the implementation and benchmarking of the derived formalism in a subsequent article of this series.« less

Results Oriented Benchmarking: The Evolution of Benchmarking at NASA from Competitive Comparisons to World Class Space Partnerships

NASA Technical Reports Server (NTRS)

Bell, Michael A.

1999-01-01

Informal benchmarking using personal or professional networks has taken place for many years at the Kennedy Space Center (KSC). The National Aeronautics and Space Administration (NASA) recognized early on, the need to formalize the benchmarking process for better utilization of resources and improved benchmarking performance. The need to compete in a faster, better, cheaper environment has been the catalyst for formalizing these efforts. A pioneering benchmarking consortium was chartered at KSC in January 1994. The consortium known as the Kennedy Benchmarking Clearinghouse (KBC), is a collaborative effort of NASA and all major KSC contractors. The charter of this consortium is to facilitate effective benchmarking, and leverage the resulting quality improvements across KSC. The KBC acts as a resource with experienced facilitators and a proven process. One of the initial actions of the KBC was to develop a holistic methodology for Center-wide benchmarking. This approach to Benchmarking integrates the best features of proven benchmarking models (i.e., Camp, Spendolini, Watson, and Balm). This cost-effective alternative to conventional Benchmarking approaches has provided a foundation for consistent benchmarking at KSC through the development of common terminology, tools, and techniques. Through these efforts a foundation and infrastructure has been built which allows short duration benchmarking studies yielding results gleaned from world class partners that can be readily implemented. The KBC has been recognized with the Silver Medal Award (in the applied research category) from the International Benchmarking Clearinghouse.

Toxicological benchmarks for screening potential contaminants of concern for effects on aquatic biota: 1996 revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II; Tsao, C.L.

1996-06-01

This report presents potential screening benchmarks for protection of aquatic life form contaminants in water. Because there is no guidance for screening for benchmarks, a set of alternative benchmarks is presented herein. This report presents the alternative benchmarks for chemicals that have been detected on the Oak Ridge Reservation. It also presents the data used to calculate the benchmarks and the sources of the data. It compares the benchmarks and discusses their relative conservatism and utility. Also included is the updates of benchmark values where appropriate, new benchmark values, secondary sources are replaced by primary sources, and a more completemore » documentation of the sources and derivation of all values are presented.« less

Benchmarking in emergency health systems.

PubMed

Kennedy, Marcus P; Allen, Jacqueline; Allen, Greg

2002-12-01

This paper discusses the role of benchmarking as a component of quality management. It describes the historical background of benchmarking, its competitive origin and the requirement in today's health environment for a more collaborative approach. The classical 'functional and generic' types of benchmarking are discussed with a suggestion to adopt a different terminology that describes the purpose and practicalities of benchmarking. Benchmarking is not without risks. The consequence of inappropriate focus and the need for a balanced overview of process is explored. The competition that is intrinsic to benchmarking is questioned and the negative impact it may have on improvement strategies in poorly performing organizations is recognized. The difficulty in achieving cross-organizational validity in benchmarking is emphasized, as is the need to scrutinize benchmarking measures. The cost effectiveness of benchmarking projects is questioned and the concept of 'best value, best practice' in an environment of fixed resources is examined.

The NAS parallel benchmarks

NASA Technical Reports Server (NTRS)

Bailey, David (Editor); Barton, John (Editor); Lasinski, Thomas (Editor); Simon, Horst (Editor)

1993-01-01

A new set of benchmarks was developed for the performance evaluation of highly parallel supercomputers. These benchmarks consist of a set of kernels, the 'Parallel Kernels,' and a simulated application benchmark. Together they mimic the computation and data movement characteristics of large scale computational fluid dynamics (CFD) applications. The principal distinguishing feature of these benchmarks is their 'pencil and paper' specification - all details of these benchmarks are specified only algorithmically. In this way many of the difficulties associated with conventional benchmarking approaches on highly parallel systems are avoided.

Benchmarking and Performance Measurement.

ERIC Educational Resources Information Center

Town, J. Stephen

This paper defines benchmarking and its relationship to quality management, describes a project which applied the technique in a library context, and explores the relationship between performance measurement and benchmarking. Numerous benchmarking methods contain similar elements: deciding what to benchmark; identifying partners; gathering…

HPC Analytics Support. Requirements for Uncertainty Quantification Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paulson, Patrick R.; Purohit, Sumit; Rodriguez, Luke R.

2015-05-01

This report outlines techniques for extending benchmark generation products so they support uncertainty quantification by benchmarked systems. We describe how uncertainty quantification requirements can be presented to candidate analytical tools supporting SPARQL. We describe benchmark data sets for evaluating uncertainty quantification, as well as an approach for using our benchmark generator to produce data sets for generating benchmark data sets.

Toxicological Benchmarks for Screening of Potential Contaminants of Concern for Effects on Aquatic Biota on the Oak Ridge Reservation, Oak Ridge, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W., II

1993-01-01

One of the initial stages in ecological risk assessment of hazardous waste sites is the screening of contaminants to determine which, if any, of them are worthy of further consideration; this process is termed contaminant screening. Screening is performed by comparing concentrations in ambient media to benchmark concentrations that are either indicative of a high likelihood of significant effects (upper screening benchmarks) or of a very low likelihood of significant effects (lower screening benchmarks). Exceedance of an upper screening benchmark indicates that the chemical in question is clearly of concern and remedial actions are likely to be needed. Exceedance ofmore » a lower screening benchmark indicates that a contaminant is of concern unless other information indicates that the data are unreliable or the comparison is inappropriate. Chemicals with concentrations below the lower benchmark are not of concern if the ambient data are judged to be adequate. This report presents potential screening benchmarks for protection of aquatic life from contaminants in water. Because there is no guidance for screening benchmarks, a set of alternative benchmarks is presented herein. The alternative benchmarks are based on different conceptual approaches to estimating concentrations causing significant effects. For the upper screening benchmark, there are the acute National Ambient Water Quality Criteria (NAWQC) and the Secondary Acute Values (SAV). The SAV concentrations are values estimated with 80% confidence not to exceed the unknown acute NAWQC for those chemicals with no NAWQC. The alternative chronic benchmarks are the chronic NAWQC, the Secondary Chronic Value (SCV), the lowest chronic values for fish and daphnids, the lowest EC20 for fish and daphnids from chronic toxicity tests, the estimated EC20 for a sensitive species, and the concentration estimated to cause a 20% reduction in the recruit abundance of largemouth bass. It is recommended that ambient chemical concentrations be compared to all of these benchmarks. If NAWQC are exceeded, the chemicals must be contaminants of concern because the NAWQC are applicable or relevant and appropriate requirements (ARARs). If NAWQC are not exceeded, but other benchmarks are, contaminants should be selected on the basis of the number of benchmarks exceeded and the conservatism of the particular benchmark values, as discussed in the text. To the extent that toxicity data are available, this report presents the alternative benchmarks for chemicals that have been detected on the Oak Ridge Reservation. It also presents the data used to calculate the benchmarks and the sources of the data. It compares the benchmarks and discusses their relative conservatism and utility. This report supersedes a prior aquatic benchmarks report (Suter and Mabrey 1994). It adds two new types of benchmarks. It also updates the benchmark values where appropriate, adds some new benchmark values, replaces secondary sources with primary sources, and provides more complete documentation of the sources and derivation of all values.« less

The KMAT: Benchmarking Knowledge Management.

ERIC Educational Resources Information Center

de Jager, Martha

Provides an overview of knowledge management and benchmarking, including the benefits and methods of benchmarking (e.g., competitive, cooperative, collaborative, and internal benchmarking). Arthur Andersen's KMAT (Knowledge Management Assessment Tool) is described. The KMAT is a collaborative benchmarking tool, designed to help organizations make…

The NAS parallel benchmarks

NASA Technical Reports Server (NTRS)

Bailey, D. H.; Barszcz, E.; Barton, J. T.; Carter, R. L.; Lasinski, T. A.; Browning, D. S.; Dagum, L.; Fatoohi, R. A.; Frederickson, P. O.; Schreiber, R. S.

1991-01-01

A new set of benchmarks has been developed for the performance evaluation of highly parallel supercomputers in the framework of the NASA Ames Numerical Aerodynamic Simulation (NAS) Program. These consist of five 'parallel kernel' benchmarks and three 'simulated application' benchmarks. Together they mimic the computation and data movement characteristics of large-scale computational fluid dynamics applications. The principal distinguishing feature of these benchmarks is their 'pencil and paper' specification-all details of these benchmarks are specified only algorithmically. In this way many of the difficulties associated with conventional benchmarking approaches on highly parallel systems are avoided.

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Benchmark-equivalent health benefits coverage. 440... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Benchmark-equivalent health benefits coverage. 440... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate...

Collider Interplay for Supersymmetry, Higgs and Dark Matter

DOE PAGES

Buchmueller, Oliver; Citron, M.; Ellis, J.; ...

2015-10-01

Here, we discuss the potential impacts on the CMSSM of future LHC runs and possible e +e – and higher-energy proton–proton colliders, considering searches for supersymmetry via /E T events, precision electroweak physics, Higgs measurements and dark matter searches. We validate and present estimates of the physics reach for exclusion or discovery of supersymmetry via /E T searches at the LHC, which should cover the low-mass regions of the CMSSM parameter space favoured in a recent global analysis. As we illustrate with a low-mass benchmark point, a discovery would make possible accurate LHC measurements of sparticle masses using the MT2more » variable, which could be combined with cross-section and other measurements to constrain the gluino, squark and stop masses and hence the soft supersymmetry-breaking parameters m 0,m 1/2 and A 0 of the CMSSM. Slepton measurements at CLIC would enable m 0 and m 1/2 to be determined with high precision. If supersymmetry is indeed discovered in the low-mass region, precision electroweak and Higgs measurements with a future circular e +e – collider (FCC-ee, also known as TLEP) combined with LHC measurements would provide tests of the CMSSM at the loop level. If supersymmetry is not discovered at the LHC, it is likely to lie somewhere along a focus-point, stop-coannihilation strip or direct-channel A / H resonance funnel. We discuss the prospects for discovering supersymmetry along these strips at a future circular proton–proton collider such as FCC-hh. Illustrative benchmark points on these strips indicate that also in this case FCC-ee could provide tests of the CMSSM at the loop level.« less

The importance of benchmarking habitat structure and composition for understanding the extent of fishing impacts in soft sediment ecosystems

NASA Astrophysics Data System (ADS)

Handley, Sean J.; Willis, Trevor J.; Cole, Russell G.; Bradley, Anna; Cairney, Daniel J.; Brown, Stephen N.; Carter, Megan E.

2014-02-01

Trawling and dredge fisheries remove vulnerable fauna, homogenise sediments and assemblages, and break down biogenic habitats, but the full extent of these effects can be difficult to quantify in the absence of adequate control sites. Our study utilised rare control sites containing biogenic habitat, the Separation Point exclusion zone, formally protected for 28 years, as the basis for assessing the degree of change experienced by adjacent areas subject to benthic fishing. Sidescan sonar surveys verified that intensive trawling and dredging occurred in areas adjacent to, but not inside, the exclusion area. We compared sediment composition, biogenic cover, macrofaunal assemblages, biomass, and productivity of the benthos, inside and outside the exclusion zone. Disturbed sites were dominated by fine mud, with little or no shell-gravel, reduced number of species, and loss of large bodied animals, with concomitant reductions in biomass and productivity. At protected sites, large, rarer molluscs were more abundant and contributed the most to size-based estimates of productivity and biomass. Functional changes in fished assemblages were consistent with previously reported relative increases in scavengers, predators and deposit feeders at the expense of filter feeders and a grazer. We propose that the colonisation of biogenic species in protected sites was contingent on the presence of shell-gravel atop these soft sediments. The process of sediment homogenisation by bottom fishing and elimination of shell-gravels from surficial sediments appeared to have occurred over decades - a ‘shifting baseline’. Therefore, benchmarking historical sediment structure at control site like the Separation Point exclusion zone is necessary to determine the full extent of physical habitat change wrought by contact gears on sheltered soft sediment habitats to better underpin appropriate conservation, restoration or fisheries management goals.

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Benchmark health benefits coverage. 440.330 Section 440.330 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...

Toxicological benchmarks for screening potential contaminants of concern for effects on aquatic biota: 1994 Revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II; Mabrey, J.B.

1994-07-01

This report presents potential screening benchmarks for protection of aquatic life from contaminants in water. Because there is no guidance for screening benchmarks, a set of alternative benchmarks is presented herein. The alternative benchmarks are based on different conceptual approaches to estimating concentrations causing significant effects. For the upper screening benchmark, there are the acute National Ambient Water Quality Criteria (NAWQC) and the Secondary Acute Values (SAV). The SAV concentrations are values estimated with 80% confidence not to exceed the unknown acute NAWQC for those chemicals with no NAWQC. The alternative chronic benchmarks are the chronic NAWQC, the Secondary Chronicmore » Value (SCV), the lowest chronic values for fish and daphnids from chronic toxicity tests, the estimated EC20 for a sensitive species, and the concentration estimated to cause a 20% reduction in the recruit abundance of largemouth bass. It is recommended that ambient chemical concentrations be compared to all of these benchmarks. If NAWQC are exceeded, the chemicals must be contaminants of concern because the NAWQC are applicable or relevant and appropriate requirements (ARARs). If NAWQC are not exceeded, but other benchmarks are, contaminants should be selected on the basis of the number of benchmarks exceeded and the conservatism of the particular benchmark values, as discussed in the text. To the extent that toxicity data are available, this report presents the alternative benchmarks for chemicals that have been detected on the Oak Ridge Reservation. It also presents the data used to calculate benchmarks and the sources of the data. It compares the benchmarks and discusses their relative conservatism and utility.« less

Raising Quality and Achievement. A College Guide to Benchmarking.

ERIC Educational Resources Information Center

Owen, Jane

This booklet introduces the principles and practices of benchmarking as a way of raising quality and achievement at further education colleges in Britain. Section 1 defines the concept of benchmarking. Section 2 explains what benchmarking is not and the steps that should be taken before benchmarking is initiated. The following aspects and…

Benchmarking in Education: Tech Prep, a Case in Point. IEE Brief Number 8.

ERIC Educational Resources Information Center

Inger, Morton

Benchmarking is a process by which organizations compare their practices, processes, and outcomes to standards of excellence in a systematic way. The benchmarking process entails the following essential steps: determining what to benchmark and establishing internal baseline data; identifying the benchmark; determining how that standard has been…

Benchmarks: The Development of a New Approach to Student Evaluation.

ERIC Educational Resources Information Center

Larter, Sylvia

The Toronto Board of Education Benchmarks are libraries of reference materials that demonstrate student achievement at various levels. Each library contains video benchmarks, print benchmarks, a staff handbook, and summary and introductory documents. This book is about the development and the history of the benchmark program. It has taken over 3…

HS06 Benchmark for an ARM Server

NASA Astrophysics Data System (ADS)

Kluth, Stefan

2014-06-01

We benchmarked an ARM cortex-A9 based server system with a four-core CPU running at 1.1 GHz. The system used Ubuntu 12.04 as operating system and the HEPSPEC 2006 (HS06) benchmarking suite was compiled natively with gcc-4.4 on the system. The benchmark was run for various settings of the relevant gcc compiler options. We did not find significant influence from the compiler options on the benchmark result. The final HS06 benchmark result is 10.4.

PMLB: a large benchmark suite for machine learning evaluation and comparison.

PubMed

Olson, Randal S; La Cava, William; Orzechowski, Patryk; Urbanowicz, Ryan J; Moore, Jason H

2017-01-01

The selection, development, or comparison of machine learning methods in data mining can be a difficult task based on the target problem and goals of a particular study. Numerous publicly available real-world and simulated benchmark datasets have emerged from different sources, but their organization and adoption as standards have been inconsistent. As such, selecting and curating specific benchmarks remains an unnecessary burden on machine learning practitioners and data scientists. The present study introduces an accessible, curated, and developing public benchmark resource to facilitate identification of the strengths and weaknesses of different machine learning methodologies. We compare meta-features among the current set of benchmark datasets in this resource to characterize the diversity of available data. Finally, we apply a number of established machine learning methods to the entire benchmark suite and analyze how datasets and algorithms cluster in terms of performance. From this study, we find that existing benchmarks lack the diversity to properly benchmark machine learning algorithms, and there are several gaps in benchmarking problems that still need to be considered. This work represents another important step towards understanding the limitations of popular benchmarking suites and developing a resource that connects existing benchmarking standards to more diverse and efficient standards in the future.

The General Concept of Benchmarking and Its Application in Higher Education in Europe

ERIC Educational Resources Information Center

Nazarko, Joanicjusz; Kuzmicz, Katarzyna Anna; Szubzda-Prutis, Elzbieta; Urban, Joanna

2009-01-01

The purposes of this paper are twofold: a presentation of the theoretical basis of benchmarking and a discussion on practical benchmarking applications. Benchmarking is also analyzed as a productivity accelerator. The authors study benchmarking usage in the private and public sectors with due consideration of the specificities of the two areas.…

Benchmarking reference services: an introduction.

PubMed

Marshall, J G; Buchanan, H S

1995-01-01

Benchmarking is based on the common sense idea that someone else, either inside or outside of libraries, has found a better way of doing certain things and that your own library's performance can be improved by finding out how others do things and adopting the best practices you find. Benchmarking is one of the tools used for achieving continuous improvement in Total Quality Management (TQM) programs. Although benchmarking can be done on an informal basis, TQM puts considerable emphasis on formal data collection and performance measurement. Used to its full potential, benchmarking can provide a common measuring stick to evaluate process performance. This article introduces the general concept of benchmarking, linking it whenever possible to reference services in health sciences libraries. Data collection instruments that have potential application in benchmarking studies are discussed and the need to develop common measurement tools to facilitate benchmarking is emphasized.

Taking the Battle Upstream: Towards a Benchmarking Role for NATO

DTIC Science & Technology

2012-09-01

Benchmark.........................................................................................14 Figure 8. World Bank Benchmarking Work on Quality...Search of a Benchmarking Theory for the Public Sector.” 16     Figure 8. World Bank Benchmarking Work on Quality of Governance One of the most...the Ministries of Defense in the countries in which it works ). Another interesting innovation is that for comparison purposes, McKinsey categorized

Benchmarks--Standards Comparisons. Math Competencies: EFF Benchmarks Comparison [and] Reading Competencies: EFF Benchmarks Comparison [and] Writing Competencies: EFF Benchmarks Comparison.

ERIC Educational Resources Information Center

Kent State Univ., OH. Ohio Literacy Resource Center.

This document is intended to show the relationship between Ohio's Standards and Competencies, Equipped for the Future's (EFF's) Standards and Components of Performance, and Ohio's Revised Benchmarks. The document is divided into three parts, with Part 1 covering mathematics instruction, Part 2 covering reading instruction, and Part 3 covering…

How do I know if my forecasts are better? Using benchmarks in hydrological ensemble prediction

NASA Astrophysics Data System (ADS)

Pappenberger, F.; Ramos, M. H.; Cloke, H. L.; Wetterhall, F.; Alfieri, L.; Bogner, K.; Mueller, A.; Salamon, P.

2015-03-01

The skill of a forecast can be assessed by comparing the relative proximity of both the forecast and a benchmark to the observations. Example benchmarks include climatology or a naïve forecast. Hydrological ensemble prediction systems (HEPS) are currently transforming the hydrological forecasting environment but in this new field there is little information to guide researchers and operational forecasters on how benchmarks can be best used to evaluate their probabilistic forecasts. In this study, it is identified that the forecast skill calculated can vary depending on the benchmark selected and that the selection of a benchmark for determining forecasting system skill is sensitive to a number of hydrological and system factors. A benchmark intercomparison experiment is then undertaken using the continuous ranked probability score (CRPS), a reference forecasting system and a suite of 23 different methods to derive benchmarks. The benchmarks are assessed within the operational set-up of the European Flood Awareness System (EFAS) to determine those that are 'toughest to beat' and so give the most robust discrimination of forecast skill, particularly for the spatial average fields that EFAS relies upon. Evaluating against an observed discharge proxy the benchmark that has most utility for EFAS and avoids the most naïve skill across different hydrological situations is found to be meteorological persistency. This benchmark uses the latest meteorological observations of precipitation and temperature to drive the hydrological model. Hydrological long term average benchmarks, which are currently used in EFAS, are very easily beaten by the forecasting system and the use of these produces much naïve skill. When decomposed into seasons, the advanced meteorological benchmarks, which make use of meteorological observations from the past 20 years at the same calendar date, have the most skill discrimination. They are also good at discriminating skill in low flows and for all catchment sizes. Simpler meteorological benchmarks are particularly useful for high flows. Recommendations for EFAS are to move to routine use of meteorological persistency, an advanced meteorological benchmark and a simple meteorological benchmark in order to provide a robust evaluation of forecast skill. This work provides the first comprehensive evidence on how benchmarks can be used in evaluation of skill in probabilistic hydrological forecasts and which benchmarks are most useful for skill discrimination and avoidance of naïve skill in a large scale HEPS. It is recommended that all HEPS use the evidence and methodology provided here to evaluate which benchmarks to employ; so forecasters can have trust in their skill evaluation and will have confidence that their forecasts are indeed better.

A benchmarking method to measure dietary absorption efficiency of chemicals by fish.

PubMed

Xiao, Ruiyang; Adolfsson-Erici, Margaretha; Åkerman, Gun; McLachlan, Michael S; MacLeod, Matthew

2013-12-01

Understanding the dietary absorption efficiency of chemicals in the gastrointestinal tract of fish is important from both a scientific and a regulatory point of view. However, reported fish absorption efficiencies for well-studied chemicals are highly variable. In the present study, the authors developed and exploited an internal chemical benchmarking method that has the potential to reduce uncertainty and variability and, thus, to improve the precision of measurements of fish absorption efficiency. The authors applied the benchmarking method to measure the gross absorption efficiency for 15 chemicals with a wide range of physicochemical properties and structures. They selected 2,2',5,6'-tetrachlorobiphenyl (PCB53) and decabromodiphenyl ethane as absorbable and nonabsorbable benchmarks, respectively. Quantities of chemicals determined in fish were benchmarked to the fraction of PCB53 recovered in fish, and quantities of chemicals determined in feces were benchmarked to the fraction of decabromodiphenyl ethane recovered in feces. The performance of the benchmarking procedure was evaluated based on the recovery of the test chemicals and precision of absorption efficiency from repeated tests. Benchmarking did not improve the precision of the measurements; after benchmarking, however, the median recovery for 15 chemicals was 106%, and variability of recoveries was reduced compared with before benchmarking, suggesting that benchmarking could account for incomplete extraction of chemical in fish and incomplete collection of feces from different tests. © 2013 SETAC.

Benchmark Evaluation of Start-Up and Zero-Power Measurements at the High-Temperature Engineering Test Reactor

DOE PAGES

Bess, John D.; Fujimoto, Nozomu

2014-10-09

Benchmark models were developed to evaluate six cold-critical and two warm-critical, zero-power measurements of the HTTR. Additional measurements of a fully-loaded subcritical configuration, core excess reactivity, shutdown margins, six isothermal temperature coefficients, and axial reaction-rate distributions were also evaluated as acceptable benchmark experiments. Insufficient information is publicly available to develop finely-detailed models of the HTTR as much of the design information is still proprietary. However, the uncertainties in the benchmark models are judged to be of sufficient magnitude to encompass any biases and bias uncertainties incurred through the simplification process used to develop the benchmark models. Dominant uncertainties in themore » experimental keff for all core configurations come from uncertainties in the impurity content of the various graphite blocks that comprise the HTTR. Monte Carlo calculations of keff are between approximately 0.9 % and 2.7 % greater than the benchmark values. Reevaluation of the HTTR models as additional information becomes available could improve the quality of this benchmark and possibly reduce the computational biases. High-quality characterization of graphite impurities would significantly improve the quality of the HTTR benchmark assessment. Simulation of the other reactor physics measurements are in good agreement with the benchmark experiment values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments.« less

How to achieve and prove performance improvement - 15 years of experience in German wastewater benchmarking.

PubMed

Bertzbach, F; Franz, T; Möller, K

2012-01-01

This paper shows the results of performance improvement, which have been achieved in benchmarking projects in the wastewater industry in Germany over the last 15 years. A huge number of changes in operational practice and also in achieved annual savings can be shown, induced in particular by benchmarking at process level. Investigation of this question produces some general findings for the inclusion of performance improvement in a benchmarking project and for the communication of its results. Thus, we elaborate on the concept of benchmarking at both utility and process level, which is still a necessary distinction for the integration of performance improvement into our benchmarking approach. To achieve performance improvement via benchmarking it should be made quite clear that this outcome depends, on one hand, on a well conducted benchmarking programme and, on the other, on the individual situation within each participating utility.

Benchmarking clinical photography services in the NHS.

PubMed

Arbon, Giles

2015-01-01

Benchmarking is used in services across the National Health Service (NHS) using various benchmarking programs. Clinical photography services do not have a program in place and services have to rely on ad hoc surveys of other services. A trial benchmarking exercise was undertaken with 13 services in NHS Trusts. This highlights valuable data and comparisons that can be used to benchmark and improve services throughout the profession.

A Seafloor Benchmark for 3-dimensional Geodesy

NASA Astrophysics Data System (ADS)

Chadwell, C. D.; Webb, S. C.; Nooner, S. L.

2014-12-01

We have developed an inexpensive, permanent seafloor benchmark to increase the longevity of seafloor geodetic measurements. The benchmark provides a physical tie to the sea floor lasting for decades (perhaps longer) on which geodetic sensors can be repeatedly placed and removed with millimeter resolution. Global coordinates estimated with seafloor geodetic techniques will remain attached to the benchmark allowing for the interchange of sensors as they fail or become obsolete, or for the sensors to be removed and used elsewhere, all the while maintaining a coherent series of positions referenced to the benchmark. The benchmark has been designed to free fall from the sea surface with transponders attached. The transponder can be recalled via an acoustic command sent from the surface to release from the benchmark and freely float to the sea surface for recovery. The duration of the sensor attachment to the benchmark will last from a few days to a few years depending on the specific needs of the experiment. The recovered sensors are then available to be reused at other locations, or again at the same site in the future. Three pins on the sensor frame mate precisely and unambiguously with three grooves on the benchmark. To reoccupy a benchmark a Remotely Operated Vehicle (ROV) uses its manipulator arm to place the sensor pins into the benchmark grooves. In June 2014 we deployed four benchmarks offshore central Oregon. We used the ROV Jason to successfully demonstrate the removal and replacement of packages onto the benchmark. We will show the benchmark design and its operational capabilities. Presently models of megathrust slip within the Cascadia Subduction Zone (CSZ) are mostly constrained by the sub-aerial GPS vectors from the Plate Boundary Observatory, a part of Earthscope. More long-lived seafloor geodetic measures are needed to better understand the earthquake and tsunami risk associated with a large rupture of the thrust fault within the Cascadia subduction zone. Using a ROV to place and remove sensors on the benchmarks will significantly reduce the number of sensors required by the community to monitor offshore strain in subduction zones.

The Model Averaging for Dichotomous Response Benchmark Dose (MADr-BMD) Tool

EPA Pesticide Factsheets

Providing quantal response models, which are also used in the U.S. EPA benchmark dose software suite, and generates a model-averaged dose response model to generate benchmark dose and benchmark dose lower bound estimates.

Benchmarking--Measuring and Comparing for Continuous Improvement.

ERIC Educational Resources Information Center

Henczel, Sue

2002-01-01

Discussion of benchmarking focuses on the use of internal and external benchmarking by special librarians. Highlights include defining types of benchmarking; historical development; benefits, including efficiency, improved performance, increased competitiveness, and better decision making; problems, including inappropriate adaptation; developing a…

Developing Benchmarks for Solar Radio Bursts

NASA Astrophysics Data System (ADS)

Biesecker, D. A.; White, S. M.; Gopalswamy, N.; Black, C.; Domm, P.; Love, J. J.; Pierson, J.

2016-12-01

Solar radio bursts can interfere with radar, communication, and tracking signals. In severe cases, radio bursts can inhibit the successful use of radio communications and disrupt a wide range of systems that are reliant on Position, Navigation, and Timing services on timescales ranging from minutes to hours across wide areas on the dayside of Earth. The White House's Space Weather Action Plan has asked for solar radio burst intensity benchmarks for an event occurrence frequency of 1 in 100 years and also a theoretical maximum intensity benchmark. The solar radio benchmark team was also asked to define the wavelength/frequency bands of interest. The benchmark team developed preliminary (phase 1) benchmarks for the VHF (30-300 MHz), UHF (300-3000 MHz), GPS (1176-1602 MHz), F10.7 (2800 MHz), and Microwave (4000-20000) bands. The preliminary benchmarks were derived based on previously published work. Limitations in the published work will be addressed in phase 2 of the benchmark process. In addition, deriving theoretical maxima requires additional work, where it is even possible to, in order to meet the Action Plan objectives. In this presentation, we will present the phase 1 benchmarks and the basis used to derive them. We will also present the work that needs to be done in order to complete the final, or phase 2 benchmarks.

Benchmarking in national health service procurement in Scotland.

PubMed

Walker, Scott; Masson, Ron; Telford, Ronnie; White, David

2007-11-01

The paper reports the results of a study on benchmarking activities undertaken by the procurement organization within the National Health Service (NHS) in Scotland, namely National Procurement (previously Scottish Healthcare Supplies Contracts Branch). NHS performance is of course politically important, and benchmarking is increasingly seen as a means to improve performance, so the study was carried out to determine if the current benchmarking approaches could be enhanced. A review of the benchmarking activities used by the private sector, local government and NHS organizations was carried out to establish a framework of the motivations, benefits, problems and costs associated with benchmarking. This framework was used to carry out the research through case studies and a questionnaire survey of NHS procurement organizations both in Scotland and other parts of the UK. Nine of the 16 Scottish Health Boards surveyed reported carrying out benchmarking during the last three years. The findings of the research were that there were similarities in approaches between local government and NHS Scotland Health, but differences between NHS Scotland and other UK NHS procurement organizations. Benefits were seen as significant and it was recommended that National Procurement should pursue the formation of a benchmarking group with members drawn from NHS Scotland and external benchmarking bodies to establish measures to be used in benchmarking across the whole of NHS Scotland.

Targeting the affordability of cigarettes: a new benchmark for taxation policy in low-income and-middle-income countries.

PubMed

Blecher, Evan

2010-08-01

To investigate the appropriateness of tax incidence (the percentage of the retail price occupied by taxes) benchmarking in low-income and-middle-income countries (LMICs) with rapidly growing economies and to explore the viability of an alternative tax policy rule based on the affordability of cigarettes. The paper outlines criticisms of tax incidence benchmarking, particularly in the context of LMICs. It then considers an affordability-based benchmark using relative income price (RIP) as a measure of affordability. The RIP measures the percentage of annual per capita GDP required to purchase 100 packs of cigarettes. Using South Africa as a case study of an LMIC, future consumption is simulated using both tax incidence benchmarks and affordability benchmarks. I show that a tax incidence benchmark is not an optimal policy tool in South Africa and that an affordability benchmark could be a more effective means of reducing tobacco consumption in the future. Although a tax incidence benchmark was successful in increasing prices and reducing tobacco consumption in South Africa in the past, this approach has drawbacks, particularly in the context of a rapidly growing LMIC economy. An affordability benchmark represents an appropriate alternative that would be more effective in reducing future cigarette consumption.

Benchmarking: applications to transfusion medicine.

PubMed

Apelseth, Torunn Oveland; Molnar, Laura; Arnold, Emmy; Heddle, Nancy M

2012-10-01

Benchmarking is as a structured continuous collaborative process in which comparisons for selected indicators are used to identify factors that, when implemented, will improve transfusion practices. This study aimed to identify transfusion medicine studies reporting on benchmarking, summarize the benchmarking approaches used, and identify important considerations to move the concept of benchmarking forward in the field of transfusion medicine. A systematic review of published literature was performed to identify transfusion medicine-related studies that compared at least 2 separate institutions or regions with the intention of benchmarking focusing on 4 areas: blood utilization, safety, operational aspects, and blood donation. Forty-five studies were included: blood utilization (n = 35), safety (n = 5), operational aspects of transfusion medicine (n = 5), and blood donation (n = 0). Based on predefined criteria, 7 publications were classified as benchmarking, 2 as trending, and 36 as single-event studies. Three models of benchmarking are described: (1) a regional benchmarking program that collects and links relevant data from existing electronic sources, (2) a sentinel site model where data from a limited number of sites are collected, and (3) an institutional-initiated model where a site identifies indicators of interest and approaches other institutions. Benchmarking approaches are needed in the field of transfusion medicine. Major challenges include defining best practices and developing cost-effective methods of data collection. For those interested in initiating a benchmarking program, the sentinel site model may be most effective and sustainable as a starting point, although the regional model would be the ideal goal. Copyright © 2012 Elsevier Inc. All rights reserved.

Self-organising mixture autoregressive model for non-stationary time series modelling.

PubMed

Ni, He; Yin, Hujun

2008-12-01

Modelling non-stationary time series has been a difficult task for both parametric and nonparametric methods. One promising solution is to combine the flexibility of nonparametric models with the simplicity of parametric models. In this paper, the self-organising mixture autoregressive (SOMAR) network is adopted as a such mixture model. It breaks time series into underlying segments and at the same time fits local linear regressive models to the clusters of segments. In such a way, a global non-stationary time series is represented by a dynamic set of local linear regressive models. Neural gas is used for a more flexible structure of the mixture model. Furthermore, a new similarity measure has been introduced in the self-organising network to better quantify the similarity of time series segments. The network can be used naturally in modelling and forecasting non-stationary time series. Experiments on artificial, benchmark time series (e.g. Mackey-Glass) and real-world data (e.g. numbers of sunspots and Forex rates) are presented and the results show that the proposed SOMAR network is effective and superior to other similar approaches.

Using deep learning to investigate the neuroimaging correlates of psychiatric and neurological disorders: Methods and applications.

PubMed

Vieira, Sandra; Pinaya, Walter H L; Mechelli, Andrea

2017-03-01

Deep learning (DL) is a family of machine learning methods that has gained considerable attention in the scientific community, breaking benchmark records in areas such as speech and visual recognition. DL differs from conventional machine learning methods by virtue of its ability to learn the optimal representation from the raw data through consecutive nonlinear transformations, achieving increasingly higher levels of abstraction and complexity. Given its ability to detect abstract and complex patterns, DL has been applied in neuroimaging studies of psychiatric and neurological disorders, which are characterised by subtle and diffuse alterations. Here we introduce the underlying concepts of DL and review studies that have used this approach to classify brain-based disorders. The results of these studies indicate that DL could be a powerful tool in the current search for biomarkers of psychiatric and neurologic disease. We conclude our review by discussing the main promises and challenges of using DL to elucidate brain-based disorders, as well as possible directions for future research. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Multiloop Integral System Test (MIST): MIST Facility Functional Specification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habib, T F; Koksal, C G; Moskal, T E

1991-04-01

The Multiloop Integral System Test (MIST) is part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox designed plants. MIST is sponsored by the US Nuclear Regulatory Commission, the Babcock Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral facilities to address the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility --more » the Once Through Integral System (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST Functional Specification documents as-built design features, dimensions, instrumentation, and test approach. It also presents the scaling basis for the facility and serves to define the scope of work for the facility design and construction. 13 refs., 112 figs., 38 tabs.« less

Quasi-degenerate perturbation theory using matrix product states

NASA Astrophysics Data System (ADS)

Sharma, Sandeep; Jeanmairet, Guillaume; Alavi, Ali

2016-01-01

In this work, we generalize the recently proposed matrix product state perturbation theory (MPSPT) for calculating energies of excited states using quasi-degenerate (QD) perturbation theory. Our formulation uses the Kirtman-Certain-Hirschfelder canonical Van Vleck perturbation theory, which gives Hermitian effective Hamiltonians at each order, and also allows one to make use of Wigner's 2n + 1 rule. Further, our formulation satisfies Granovsky's requirement of model space invariance which is important for obtaining smooth potential energy curves. Thus, when we use MPSPT with the Dyall Hamiltonian, we obtain a model space invariant version of quasi-degenerate n-electron valence state perturbation theory (NEVPT), a property that the usual formulation of QD-NEVPT2 based on a multipartitioning technique lacked. We use our method on the benchmark problems of bond breaking of LiF which shows ionic to covalent curve crossing and the twist around the double bond of ethylene where significant valence-Rydberg mixing occurs in the excited states. In accordance with our previous work, we find that multi-reference linearized coupled cluster theory is more accurate than other multi-reference theories of similar cost.

GPUs, a New Tool of Acceleration in CFD: Efficiency and Reliability on Smoothed Particle Hydrodynamics Methods

PubMed Central

Crespo, Alejandro C.; Dominguez, Jose M.; Barreiro, Anxo; Gómez-Gesteira, Moncho; Rogers, Benedict D.

2011-01-01

Smoothed Particle Hydrodynamics (SPH) is a numerical method commonly used in Computational Fluid Dynamics (CFD) to simulate complex free-surface flows. Simulations with this mesh-free particle method far exceed the capacity of a single processor. In this paper, as part of a dual-functioning code for either central processing units (CPUs) or Graphics Processor Units (GPUs), a parallelisation using GPUs is presented. The GPU parallelisation technique uses the Compute Unified Device Architecture (CUDA) of nVidia devices. Simulations with more than one million particles on a single GPU card exhibit speedups of up to two orders of magnitude over using a single-core CPU. It is demonstrated that the code achieves different speedups with different CUDA-enabled GPUs. The numerical behaviour of the SPH code is validated with a standard benchmark test case of dam break flow impacting on an obstacle where good agreement with the experimental results is observed. Both the achieved speed-ups and the quantitative agreement with experiments suggest that CUDA-based GPU programming can be used in SPH methods with efficiency and reliability. PMID:21695185

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

A Web Resource for Standardized Benchmark Datasets, Metrics, and Rosetta Protocols for Macromolecular Modeling and Design.

PubMed

Ó Conchúir, Shane; Barlow, Kyle A; Pache, Roland A; Ollikainen, Noah; Kundert, Kale; O'Meara, Matthew J; Smith, Colin A; Kortemme, Tanja

2015-01-01

The development and validation of computational macromolecular modeling and design methods depend on suitable benchmark datasets and informative metrics for comparing protocols. In addition, if a method is intended to be adopted broadly in diverse biological applications, there needs to be information on appropriate parameters for each protocol, as well as metrics describing the expected accuracy compared to experimental data. In certain disciplines, there exist established benchmarks and public resources where experts in a particular methodology are encouraged to supply their most efficient implementation of each particular benchmark. We aim to provide such a resource for protocols in macromolecular modeling and design. We present a freely accessible web resource (https://kortemmelab.ucsf.edu/benchmarks) to guide the development of protocols for protein modeling and design. The site provides benchmark datasets and metrics to compare the performance of a variety of modeling protocols using different computational sampling methods and energy functions, providing a "best practice" set of parameters for each method. Each benchmark has an associated downloadable benchmark capture archive containing the input files, analysis scripts, and tutorials for running the benchmark. The captures may be run with any suitable modeling method; we supply command lines for running the benchmarks using the Rosetta software suite. We have compiled initial benchmarks for the resource spanning three key areas: prediction of energetic effects of mutations, protein design, and protein structure prediction, each with associated state-of-the-art modeling protocols. With the help of the wider macromolecular modeling community, we hope to expand the variety of benchmarks included on the website and continue to evaluate new iterations of current methods as they become available.

Using benchmarking techniques and the 2011 maternity practices infant nutrition and care (mPINC) survey to improve performance among peer groups across the United States.

PubMed

Edwards, Roger A; Dee, Deborah; Umer, Amna; Perrine, Cria G; Shealy, Katherine R; Grummer-Strawn, Laurence M

2014-02-01

A substantial proportion of US maternity care facilities engage in practices that are not evidence-based and that interfere with breastfeeding. The CDC Survey of Maternity Practices in Infant Nutrition and Care (mPINC) showed significant variation in maternity practices among US states. The purpose of this article is to use benchmarking techniques to identify states within relevant peer groups that were top performers on mPINC survey indicators related to breastfeeding support. We used 11 indicators of breastfeeding-related maternity care from the 2011 mPINC survey and benchmarking techniques to organize and compare hospital-based maternity practices across the 50 states and Washington, DC. We created peer categories for benchmarking first by region (grouping states by West, Midwest, South, and Northeast) and then by size (grouping states by the number of maternity facilities and dividing each region into approximately equal halves based on the number of facilities). Thirty-four states had scores high enough to serve as benchmarks, and 32 states had scores low enough to reflect the lowest score gap from the benchmark on at least 1 indicator. No state served as the benchmark on more than 5 indicators and no state was furthest from the benchmark on more than 7 indicators. The small peer group benchmarks in the South, West, and Midwest were better than the large peer group benchmarks on 91%, 82%, and 36% of the indicators, respectively. In the West large, the Midwest large, the Midwest small, and the South large peer groups, 4-6 benchmarks showed that less than 50% of hospitals have ideal practice in all states. The evaluation presents benchmarks for peer group state comparisons that provide potential and feasible targets for improvement.

Hospital benchmarking: are U.S. eye hospitals ready?

PubMed

de Korne, Dirk F; van Wijngaarden, Jeroen D H; Sol, Kees J C A; Betz, Robert; Thomas, Richard C; Schein, Oliver D; Klazinga, Niek S

2012-01-01

Benchmarking is increasingly considered a useful management instrument to improve quality in health care, but little is known about its applicability in hospital settings. The aims of this study were to assess the applicability of a benchmarking project in U.S. eye hospitals and compare the results with an international initiative. We evaluated multiple cases by applying an evaluation frame abstracted from the literature to five U.S. eye hospitals that used a set of 10 indicators for efficiency benchmarking. Qualitative analysis entailed 46 semistructured face-to-face interviews with stakeholders, document analyses, and questionnaires. The case studies only partially met the conditions of the evaluation frame. Although learning and quality improvement were stated as overall purposes, the benchmarking initiative was at first focused on efficiency only. No ophthalmic outcomes were included, and clinicians were skeptical about their reporting relevance and disclosure. However, in contrast with earlier findings in international eye hospitals, all U.S. hospitals worked with internal indicators that were integrated in their performance management systems and supported benchmarking. Benchmarking can support performance management in individual hospitals. Having a certain number of comparable institutes provide similar services in a noncompetitive milieu seems to lay fertile ground for benchmarking. International benchmarking is useful only when these conditions are not met nationally. Although the literature focuses on static conditions for effective benchmarking, our case studies show that it is a highly iterative and learning process. The journey of benchmarking seems to be more important than the destination. Improving patient value (health outcomes per unit of cost) requires, however, an integrative perspective where clinicians and administrators closely cooperate on both quality and efficiency issues. If these worlds do not share such a relationship, the added "public" value of benchmarking in health care is questionable.

Development and application of freshwater sediment-toxicity benchmarks for currently used pesticides

USGS Publications Warehouse

Nowell, Lisa H.; Norman, Julia E.; Ingersoll, Christopher G.; Moran, Patrick W.

2016-01-01

Sediment-toxicity benchmarks are needed to interpret the biological significance of currently used pesticides detected in whole sediments. Two types of freshwater sediment benchmarks for pesticides were developed using spiked-sediment bioassay (SSB) data from the literature. These benchmarks can be used to interpret sediment-toxicity data or to assess the potential toxicity of pesticides in whole sediment. The Likely Effect Benchmark (LEB) defines a pesticide concentration in whole sediment above which there is a high probability of adverse effects on benthic invertebrates, and the Threshold Effect Benchmark (TEB) defines a concentration below which adverse effects are unlikely. For compounds without available SSBs, benchmarks were estimated using equilibrium partitioning (EqP). When a sediment sample contains a pesticide mixture, benchmark quotients can be summed for all detected pesticides to produce an indicator of potential toxicity for that mixture. Benchmarks were developed for 48 pesticide compounds using SSB data and 81 compounds using the EqP approach. In an example application, data for pesticides measured in sediment from 197 streams across the United States were evaluated using these benchmarks, and compared to measured toxicity from whole-sediment toxicity tests conducted with the amphipod Hyalella azteca (28-d exposures) and the midge Chironomus dilutus (10-d exposures). Amphipod survival, weight, and biomass were significantly and inversely related to summed benchmark quotients, whereas midge survival, weight, and biomass showed no relationship to benchmarks. Samples with LEB exceedances were rare (n = 3), but all were toxic to amphipods (i.e., significantly different from control). Significant toxicity to amphipods was observed for 72% of samples exceeding one or more TEBs, compared to 18% of samples below all TEBs. Factors affecting toxicity below TEBs may include the presence of contaminants other than pesticides, physical/chemical characteristics of sediment, and uncertainty in TEB values. Additional evaluations of benchmarks in relation to sediment chemistry and toxicity are ongoing.

40 CFR 141.172 - Disinfection profiling and benchmarking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... benchmarking. 141.172 Section 141.172 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Disinfection-Systems Serving 10,000 or More People § 141.172 Disinfection profiling and benchmarking. (a... sanitary surveys conducted by the State. (c) Disinfection benchmarking. (1) Any system required to develop...

42 CFR 440.390 - Assurance of transportation.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-Equivalent Coverage § 440.390 Assurance of transportation. If a benchmark or benchmark-equivalent plan does... nevertheless assure that emergency and non-emergency transportation is covered for beneficiaries enrolled in the benchmark or benchmark-equivalent plan, as required under § 431.53 of this chapter. ...

42 CFR 440.390 - Assurance of transportation.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-Equivalent Coverage § 440.390 Assurance of transportation. If a benchmark or benchmark-equivalent plan does... nevertheless assure that emergency and non-emergency transportation is covered for beneficiaries enrolled in the benchmark or benchmark-equivalent plan, as required under § 431.53 of this chapter. ...

42 CFR 440.390 - Assurance of transportation.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-Equivalent Coverage § 440.390 Assurance of transportation. If a benchmark or benchmark-equivalent plan does... nevertheless assure that emergency and non-emergency transportation is covered for beneficiaries enrolled in the benchmark or benchmark-equivalent plan, as required under § 431.53 of this chapter. ...

42 CFR 440.390 - Assurance of transportation.

Code of Federal Regulations, 2010 CFR

2010-10-01

...-Equivalent Coverage § 440.390 Assurance of transportation. If a benchmark or benchmark-equivalent plan does... nevertheless assure that emergency and non-emergency transportation is covered for beneficiaries enrolled in the benchmark or benchmark-equivalent plan, as required under § 431.53 of this chapter. ...

42 CFR 440.390 - Assurance of transportation.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-Equivalent Coverage § 440.390 Assurance of transportation. If a benchmark or benchmark-equivalent plan does... nevertheless assure that emergency and non-emergency transportation is covered for beneficiaries enrolled in the benchmark or benchmark-equivalent plan, as required under § 431.53 of this chapter. ...

The Zoo, Benchmarks & You: How To Reach the Oregon State Benchmarks with Zoo Resources.

ERIC Educational Resources Information Center

2002

This document aligns Oregon state educational benchmarks and standards with Oregon Zoo resources. Benchmark areas examined include English, mathematics, science, social studies, and career and life roles. Brief descriptions of the programs offered by the zoo are presented. (SOE)

The Isprs Benchmark on Indoor Modelling

NASA Astrophysics Data System (ADS)

Khoshelham, K.; Díaz Vilariño, L.; Peter, M.; Kang, Z.; Acharya, D.

2017-09-01

Automated generation of 3D indoor models from point cloud data has been a topic of intensive research in recent years. While results on various datasets have been reported in literature, a comparison of the performance of different methods has not been possible due to the lack of benchmark datasets and a common evaluation framework. The ISPRS benchmark on indoor modelling aims to address this issue by providing a public benchmark dataset and an evaluation framework for performance comparison of indoor modelling methods. In this paper, we present the benchmark dataset comprising several point clouds of indoor environments captured by different sensors. We also discuss the evaluation and comparison of indoor modelling methods based on manually created reference models and appropriate quality evaluation criteria. The benchmark dataset is available for download at: http://www2.isprs.org/commissions/comm4/wg5/benchmark-on-indoor-modelling.html.

Combining Phase Identification and Statistic Modeling for Automated Parallel Benchmark Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin, Ye; Ma, Xiaosong; Liu, Qing Gary

2015-01-01

Parallel application benchmarks are indispensable for evaluating/optimizing HPC software and hardware. However, it is very challenging and costly to obtain high-fidelity benchmarks reflecting the scale and complexity of state-of-the-art parallel applications. Hand-extracted synthetic benchmarks are time-and labor-intensive to create. Real applications themselves, while offering most accurate performance evaluation, are expensive to compile, port, reconfigure, and often plainly inaccessible due to security or ownership concerns. This work contributes APPRIME, a novel tool for trace-based automatic parallel benchmark generation. Taking as input standard communication-I/O traces of an application's execution, it couples accurate automatic phase identification with statistical regeneration of event parameters tomore » create compact, portable, and to some degree reconfigurable parallel application benchmarks. Experiments with four NAS Parallel Benchmarks (NPB) and three real scientific simulation codes confirm the fidelity of APPRIME benchmarks. They retain the original applications' performance characteristics, in particular the relative performance across platforms.« less

Benchmarking in Academic Pharmacy Departments

PubMed Central

Chisholm-Burns, Marie; Nappi, Jean; Gubbins, Paul O.; Ross, Leigh Ann

2010-01-01

Benchmarking in academic pharmacy, and recommendations for the potential uses of benchmarking in academic pharmacy departments are discussed in this paper. Benchmarking is the process by which practices, procedures, and performance metrics are compared to an established standard or best practice. Many businesses and industries use benchmarking to compare processes and outcomes, and ultimately plan for improvement. Institutions of higher learning have embraced benchmarking practices to facilitate measuring the quality of their educational and research programs. Benchmarking is used internally as well to justify the allocation of institutional resources or to mediate among competing demands for additional program staff or space. Surveying all chairs of academic pharmacy departments to explore benchmarking issues such as department size and composition, as well as faculty teaching, scholarly, and service productivity, could provide valuable information. To date, attempts to gather this data have had limited success. We believe this information is potentially important, urge that efforts to gather it should be continued, and offer suggestions to achieve full participation. PMID:21179251

Benchmarking in academic pharmacy departments.

PubMed

Bosso, John A; Chisholm-Burns, Marie; Nappi, Jean; Gubbins, Paul O; Ross, Leigh Ann

2010-10-11

Benchmarking in academic pharmacy, and recommendations for the potential uses of benchmarking in academic pharmacy departments are discussed in this paper. Benchmarking is the process by which practices, procedures, and performance metrics are compared to an established standard or best practice. Many businesses and industries use benchmarking to compare processes and outcomes, and ultimately plan for improvement. Institutions of higher learning have embraced benchmarking practices to facilitate measuring the quality of their educational and research programs. Benchmarking is used internally as well to justify the allocation of institutional resources or to mediate among competing demands for additional program staff or space. Surveying all chairs of academic pharmacy departments to explore benchmarking issues such as department size and composition, as well as faculty teaching, scholarly, and service productivity, could provide valuable information. To date, attempts to gather this data have had limited success. We believe this information is potentially important, urge that efforts to gather it should be continued, and offer suggestions to achieve full participation.

Evaluating the Effect of Labeled Benchmarks on Children’s Number Line Estimation Performance and Strategy Use

PubMed Central

Peeters, Dominique; Sekeris, Elke; Verschaffel, Lieven; Luwel, Koen

2017-01-01

Some authors argue that age-related improvements in number line estimation (NLE) performance result from changes in strategy use. More specifically, children’s strategy use develops from only using the origin of the number line, to using the origin and the endpoint, to eventually also relying on the midpoint of the number line. Recently, Peeters et al. (unpublished) investigated whether the provision of additional unlabeled benchmarks at 25, 50, and 75% of the number line, positively affects third and fifth graders’ NLE performance and benchmark-based strategy use. It was found that only the older children benefitted from the presence of these benchmarks at the quartiles of the number line (i.e., 25 and 75%), as they made more use of these benchmarks, leading to more accurate estimates. A possible explanation for this lack of improvement in third graders might be their inability to correctly link the presented benchmarks with their corresponding numerical values. In the present study, we investigated whether labeling these benchmarks with their corresponding numerical values, would have a positive effect on younger children’s NLE performance and quartile-based strategy use as well. Third and sixth graders were assigned to one of three conditions: (a) a control condition with an empty number line bounded by 0 at the origin and 1,000 at the endpoint, (b) an unlabeled condition with three additional external benchmarks without numerical labels at 25, 50, and 75% of the number line, and (c) a labeled condition in which these benchmarks were labeled with 250, 500, and 750, respectively. Results indicated that labeling the benchmarks has a positive effect on third graders’ NLE performance and quartile-based strategy use, whereas sixth graders already benefited from the mere provision of unlabeled benchmarks. These findings imply that children’s benchmark-based strategy use can be stimulated by adding additional externally provided benchmarks on the number line, but that, depending on children’s age and familiarity with the number range, these additional external benchmarks might need to be labeled. PMID:28713302

Evaluating the Effect of Labeled Benchmarks on Children's Number Line Estimation Performance and Strategy Use.

PubMed

Peeters, Dominique; Sekeris, Elke; Verschaffel, Lieven; Luwel, Koen

2017-01-01

Some authors argue that age-related improvements in number line estimation (NLE) performance result from changes in strategy use. More specifically, children's strategy use develops from only using the origin of the number line, to using the origin and the endpoint, to eventually also relying on the midpoint of the number line. Recently, Peeters et al. (unpublished) investigated whether the provision of additional unlabeled benchmarks at 25, 50, and 75% of the number line, positively affects third and fifth graders' NLE performance and benchmark-based strategy use. It was found that only the older children benefitted from the presence of these benchmarks at the quartiles of the number line (i.e., 25 and 75%), as they made more use of these benchmarks, leading to more accurate estimates. A possible explanation for this lack of improvement in third graders might be their inability to correctly link the presented benchmarks with their corresponding numerical values. In the present study, we investigated whether labeling these benchmarks with their corresponding numerical values, would have a positive effect on younger children's NLE performance and quartile-based strategy use as well. Third and sixth graders were assigned to one of three conditions: (a) a control condition with an empty number line bounded by 0 at the origin and 1,000 at the endpoint, (b) an unlabeled condition with three additional external benchmarks without numerical labels at 25, 50, and 75% of the number line, and (c) a labeled condition in which these benchmarks were labeled with 250, 500, and 750, respectively. Results indicated that labeling the benchmarks has a positive effect on third graders' NLE performance and quartile-based strategy use, whereas sixth graders already benefited from the mere provision of unlabeled benchmarks. These findings imply that children's benchmark-based strategy use can be stimulated by adding additional externally provided benchmarks on the number line, but that, depending on children's age and familiarity with the number range, these additional external benchmarks might need to be labeled.

Medical school benchmarking - from tools to programmes.

PubMed

Wilkinson, Tim J; Hudson, Judith N; Mccoll, Geoffrey J; Hu, Wendy C Y; Jolly, Brian C; Schuwirth, Lambert W T

2015-02-01

Benchmarking among medical schools is essential, but may result in unwanted effects. To apply a conceptual framework to selected benchmarking activities of medical schools. We present an analogy between the effects of assessment on student learning and the effects of benchmarking on medical school educational activities. A framework by which benchmarking can be evaluated was developed and applied to key current benchmarking activities in Australia and New Zealand. The analogy generated a conceptual framework that tested five questions to be considered in relation to benchmarking: what is the purpose? what are the attributes of value? what are the best tools to assess the attributes of value? what happens to the results? and, what is the likely "institutional impact" of the results? If the activities were compared against a blueprint of desirable medical graduate outcomes, notable omissions would emerge. Medical schools should benchmark their performance on a range of educational activities to ensure quality improvement and to assure stakeholders that standards are being met. Although benchmarking potentially has positive benefits, it could also result in perverse incentives with unforeseen and detrimental effects on learning if it is undertaken using only a few selected assessment tools.

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Benchmark-equivalent health benefits coverage. 440.335 Section 440.335 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 4 2014-10-01 2014-10-01 false Benchmark-equivalent health benefits coverage. 440.335 Section 440.335 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandor, Debra; Chung, Donald; Keyser, David

This report documents the CEMAC methodologies for developing and reporting annual global clean energy manufacturing benchmarks. The report reviews previously published manufacturing benchmark reports and foundational data, establishes a framework for benchmarking clean energy technologies, describes the CEMAC benchmark analysis methodologies, and describes the application of the methodologies to the manufacturing of four specific clean energy technologies.

Benchmarking for Higher Education.

ERIC Educational Resources Information Center

Jackson, Norman, Ed.; Lund, Helen, Ed.

The chapters in this collection explore the concept of benchmarking as it is being used and developed in higher education (HE). Case studies and reviews show how universities in the United Kingdom are using benchmarking to aid in self-regulation and self-improvement. The chapters are: (1) "Introduction to Benchmarking" (Norman Jackson…

How Benchmarking and Higher Education Came Together

ERIC Educational Resources Information Center

Levy, Gary D.; Ronco, Sharron L.

2012-01-01

This chapter introduces the concept of benchmarking and how higher education institutions began to use benchmarking for a variety of purposes. Here, benchmarking is defined as a strategic and structured approach whereby an organization compares aspects of its processes and/or outcomes to those of another organization or set of organizations to…

Benchmark Study of Global Clean Energy Manufacturing | Advanced

Science.gov Websites

Manufacturing Research | NREL Benchmark Study of Global Clean Energy Manufacturing Benchmark Study of Global Clean Energy Manufacturing Through a first-of-its-kind benchmark study, the Clean Energy Technology End Product.' The study examined four clean energy technologies: wind turbine components

Cross-industry benchmarking: is it applicable to the operating room?

PubMed

Marco, A P; Hart, S

2001-01-01

The use of benchmarking has been growing in nonmedical industries. This concept is being increasingly applied to medicine as the industry strives to improve quality and improve financial performance. Benchmarks can be either internal (set by the institution) or external (use other's performance as a goal). In some industries, benchmarking has crossed industry lines to identify breakthroughs in thinking. In this article, we examine whether the airline industry can be used as a source of external process benchmarking for the operating room.

Overview of TPC Benchmark E: The Next Generation of OLTP Benchmarks

NASA Astrophysics Data System (ADS)

Hogan, Trish

Set to replace the aging TPC-C, the TPC Benchmark E is the next generation OLTP benchmark, which more accurately models client database usage. TPC-E addresses the shortcomings of TPC-C. It has a much more complex workload, requires the use of RAID-protected storage, generates much less I/O, and is much cheaper and easier to set up, run, and audit. After a period of overlap, it is expected that TPC-E will become the de facto OLTP benchmark.

Implementation and validation of a conceptual benchmarking framework for patient blood management.

PubMed

Kastner, Peter; Breznik, Nada; Gombotz, Hans; Hofmann, Axel; Schreier, Günter

2015-01-01

Public health authorities and healthcare professionals are obliged to ensure high quality health service. Because of the high variability of the utilisation of blood and blood components, benchmarking is indicated in transfusion medicine. Implementation and validation of a benchmarking framework for Patient Blood Management (PBM) based on the report from the second Austrian Benchmark trial. Core modules for automatic report generation have been implemented with KNIME (Konstanz Information Miner) and validated by comparing the output with the results of the second Austrian benchmark trial. Delta analysis shows a deviation <0.1% for 95% (max. 1.4%). The framework provides a reliable tool for PBM benchmarking. The next step is technical integration with hospital information systems.

Toxicological benchmarks for potential contaminants of concern for effects on soil and litter invertebrates and heterotrophic process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Will, M.E.; Suter, G.W. II

1995-09-01

An important step in ecological risk assessments is screening the chemicals occur-ring on a site for contaminants of potential concern. Screening may be accomplished by comparing reported ambient concentrations to a set of toxicological benchmarks. Multiple endpoints for assessing risks posed by soil-borne contaminants to organisms directly impacted by them have been established. This report presents benchmarks for soil invertebrates and microbial processes and addresses only chemicals found at United States Department of Energy (DOE) sites. No benchmarks for pesticides are presented. After discussing methods, this report presents the results of the literature review and benchmark derivation for toxicity tomore » earthworms (Sect. 3), heterotrophic microbes and their processes (Sect. 4), and other invertebrates (Sect. 5). The final sections compare the benchmarks to other criteria and background and draw conclusions concerning the utility of the benchmarks.« less

Benchmarks for target tracking

NASA Astrophysics Data System (ADS)

Dunham, Darin T.; West, Philip D.

2011-09-01

The term benchmark originates from the chiseled horizontal marks that surveyors made, into which an angle-iron could be placed to bracket ("bench") a leveling rod, thus ensuring that the leveling rod can be repositioned in exactly the same place in the future. A benchmark in computer terms is the result of running a computer program, or a set of programs, in order to assess the relative performance of an object by running a number of standard tests and trials against it. This paper will discuss the history of simulation benchmarks that are being used by multiple branches of the military and agencies of the US government. These benchmarks range from missile defense applications to chemical biological situations. Typically, a benchmark is used with Monte Carlo runs in order to tease out how algorithms deal with variability and the range of possible inputs. We will also describe problems that can be solved by a benchmark.

Benchmarking Using Basic DBMS Operations

NASA Astrophysics Data System (ADS)

Crolotte, Alain; Ghazal, Ahmad

The TPC-H benchmark proved to be successful in the decision support area. Many commercial database vendors and their related hardware vendors used these benchmarks to show the superiority and competitive edge of their products. However, over time, the TPC-H became less representative of industry trends as vendors keep tuning their database to this benchmark-specific workload. In this paper, we present XMarq, a simple benchmark framework that can be used to compare various software/hardware combinations. Our benchmark model is currently composed of 25 queries that measure the performance of basic operations such as scans, aggregations, joins and index access. This benchmark model is based on the TPC-H data model due to its maturity and well-understood data generation capability. We also propose metrics to evaluate single-system performance and compare two systems. Finally we illustrate the effectiveness of this model by showing experimental results comparing two systems under different conditions.

77 FR 70643 - Patient Protection and Affordable Care Act; Standards Related to Essential Health Benefits...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... coverage \\1\\ in the individual and small group markets, Medicaid benchmark and benchmark-equivalent plans...) Act extends the coverage of the EHB package to issuers of non-grandfathered individual and small group... small group markets, and not to Medicaid benchmark or benchmark-equivalent plans. EHB applicability to...

Discovering and Implementing Best Practices to Strengthen SEAs: Collaborative Benchmarking

ERIC Educational Resources Information Center

Building State Capacity and Productivity Center, 2013

2013-01-01

This paper is written for state educational agency (SEA) leaders who are considering the benefits of collaborative benchmarking, and it addresses the following questions: (1) What does benchmarking of best practices entail?; (2) How does "collaborative benchmarking" enhance the process?; (3) How do SEAs control the process so that "their" needs…

The Concepts "Benchmarks and Benchmarking" Used in Education Planning: Teacher Education as Example

ERIC Educational Resources Information Center

Steyn, H. J.

2015-01-01

Planning in education is a structured activity that includes several phases and steps that take into account several kinds of information (Steyn, Steyn, De Waal & Wolhuter, 2002: 146). One of the sets of information that are usually considered is the (so-called) "benchmarks" and "benchmarking" regarding the focus of a…

The Craft of Benchmarking: Finding and Utilizing District-Level, Campus-Level, and Program-Level Standards.

ERIC Educational Resources Information Center

McGregor, Ellen N.; Attinasi, Louis C., Jr.

This paper describes the processes involved in selecting peer institutions for appropriate benchmarking using national databases (NCES-IPEDS). Benchmarking involves the identification of peer institutions and/or best practices in specific operational areas for the purpose of developing standards. The benchmarking process was borne in the early…

Measuring How Benchmark Assessments Affect Student Achievement. Issues & Answers. REL 2007-No. 039

ERIC Educational Resources Information Center

Henderson, Susan; Petrosino, Anthony; Guckenburg, Sarah; Hamilton, Stephen

2007-01-01

This report examines a Massachusetts pilot program for quarterly benchmark exams in middle-school mathematics, finding that program schools do not show greater gains in student achievement after a year. But that finding might reflect limited data rather than ineffective benchmark assessments. Benchmark assessments are used in many districts…

24 CFR 990.185 - Utilities expense level: Incentives for energy conservation/rate reduction.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Utility benchmarking. HUD will pursue benchmarking utility consumption at the project level as part of the... convene a meeting with representation of appropriate stakeholders to review utility benchmarking options so that HUD may determine whether or how to implement utility benchmarking to be effective in FY 2011...

Quality in E-Learning--A Conceptual Framework Based on Experiences from Three International Benchmarking Projects

ERIC Educational Resources Information Center

Ossiannilsson, E.; Landgren, L.

2012-01-01

Between 2008 and 2010, Lund University took part in three international benchmarking projects, "E-xcellence+," the "eLearning Benchmarking Exercise 2009," and the "First Dual-Mode Distance Learning Benchmarking Club." A comparison of these models revealed a rather high level of correspondence. From this finding and…

24 CFR 990.185 - Utilities expense level: Incentives for energy conservation/rate reduction.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Utility benchmarking. HUD will pursue benchmarking utility consumption at the project level as part of the... convene a meeting with representation of appropriate stakeholders to review utility benchmarking options so that HUD may determine whether or how to implement utility benchmarking to be effective in FY 2011...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

Toxicological benchmarks for screening potential contaminants of concern for effects on terrestrial plants: 1994 revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Will, M.E.; Suter, G.W. II

1994-09-01

One of the initial stages in ecological risk assessment for hazardous waste sites is screening contaminants to determine which of them are worthy of further consideration as contaminants of potential concern. This process is termed contaminant screening. It is performed by comparing measured ambient concentrations of chemicals to benchmark concentrations. Currently, no standard benchmark concentrations exist for assessing contaminants in soil with respect to their toxicity to plants. This report presents a standard method for deriving benchmarks for this purpose (phytotoxicity benchmarks), a set of data concerning effects of chemicals in soil or soil solution on plants, and a setmore » of phytotoxicity benchmarks for 38 chemicals potentially associated with United States Department of Energy (DOE) sites. In addition, background information on the phytotoxicity and occurrence of the chemicals in soils is presented, and literature describing the experiments from which data were drawn for benchmark derivation is reviewed. Chemicals that are found in soil at concentrations exceeding both the phytotoxicity benchmark and the background concentration for the soil type should be considered contaminants of potential concern.« less

Toxicological Benchmarks for Screening Potential Contaminants of Concern for Effects on Terrestrial Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II

1993-01-01

One of the initial stages in ecological risk assessment for hazardous waste sites is screening contaminants to determine which of them are worthy of further consideration as contaminants of potential concern. This process is termed contaminant screening. It is performed by comparing measured ambient concentrations of chemicals to benchmark concentrations. Currently, no standard benchmark concentrations exist for assessing contaminants in soil with respect to their toxicity to plants. This report presents a standard method for deriving benchmarks for this purpose (phytotoxicity benchmarks), a set of data concerning effects of chemicals in soil or soil solution on plants, and a setmore » of phytotoxicity benchmarks for 38 chemicals potentially associated with United States Department of Energy (DOE) sites. In addition, background information on the phytotoxicity and occurrence of the chemicals in soils is presented, and literature describing the experiments from which data were drawn for benchmark derivation is reviewed. Chemicals that are found in soil at concentrations exceeding both the phytotoxicity benchmark and the background concentration for the soil type should be considered contaminants of potential concern.« less

Structural Benchmark Creep Testing for Microcast MarM-247 Advanced Stirling Convertor E2 Heater Head Test Article SN18

NASA Technical Reports Server (NTRS)

Krause, David L.; Brewer, Ethan J.; Pawlik, Ralph

2013-01-01

This report provides test methodology details and qualitative results for the first structural benchmark creep test of an Advanced Stirling Convertor (ASC) heater head of ASC-E2 design heritage. The test article was recovered from a flight-like Microcast MarM-247 heater head specimen previously used in helium permeability testing. The test article was utilized for benchmark creep test rig preparation, wall thickness and diametral laser scan hardware metrological developments, and induction heater custom coil experiments. In addition, a benchmark creep test was performed, terminated after one week when through-thickness cracks propagated at thermocouple weld locations. Following this, it was used to develop a unique temperature measurement methodology using contact thermocouples, thereby enabling future benchmark testing to be performed without the use of conventional welded thermocouples, proven problematic for the alloy. This report includes an overview of heater head structural benchmark creep testing, the origin of this particular test article, test configuration developments accomplished using the test article, creep predictions for its benchmark creep test, qualitative structural benchmark creep test results, and a short summary.

How to Advance TPC Benchmarks with Dependability Aspects

NASA Astrophysics Data System (ADS)

Almeida, Raquel; Poess, Meikel; Nambiar, Raghunath; Patil, Indira; Vieira, Marco

Transactional systems are the core of the information systems of most organizations. Although there is general acknowledgement that failures in these systems often entail significant impact both on the proceeds and reputation of companies, the benchmarks developed and managed by the Transaction Processing Performance Council (TPC) still maintain their focus on reporting bare performance. Each TPC benchmark has to pass a list of dependability-related tests (to verify ACID properties), but not all benchmarks require measuring their performances. While TPC-E measures the recovery time of some system failures, TPC-H and TPC-C only require functional correctness of such recovery. Consequently, systems used in TPC benchmarks are tuned mostly for performance. In this paper we argue that nowadays systems should be tuned for a more comprehensive suite of dependability tests, and that a dependability metric should be part of TPC benchmark publications. The paper discusses WHY and HOW this can be achieved. Two approaches are introduced and discussed: augmenting each TPC benchmark in a customized way, by extending each specification individually; and pursuing a more unified approach, defining a generic specification that could be adjoined to any TPC benchmark.

Space Weather Action Plan Solar Radio Burst Phase 1 Benchmarks and the Steps to Phase 2

NASA Astrophysics Data System (ADS)

Biesecker, D. A.; White, S. M.; Gopalswamy, N.; Black, C.; Love, J. J.; Pierson, J.

2017-12-01

Solar radio bursts, when at the right frequency and when strong enough, can interfere with radar, communication, and tracking signals. In severe cases, radio bursts can inhibit the successful use of radio communications and disrupt a wide range of systems that are reliant on Position, Navigation, and Timing services on timescales ranging from minutes to hours across wide areas on the dayside of Earth. The White House's Space Weather Action Plan asked for solar radio burst intensity benchmarks for an event occurrence frequency of 1 in 100 years and also a theoretical maximum intensity benchmark. The benchmark team has developed preliminary (phase 1) benchmarks for the VHF (30-300 MHz), UHF (300-3000 MHz), GPS (1176-1602 MHz), F10.7 (2800 MHz), and Microwave (4000-20000) bands. The preliminary benchmarks were derived based on previously published work. Limitations in the published work will be addressed in phase 2 of the benchmark process. In addition, deriving theoretical maxima requires additional work, where it is even possible to, in order to meet the Action Plan objectives. In this presentation, we will present the phase 1 benchmarks, the basis used to derive them, and the limitations of that work. We will also discuss the work that needs to be done to complete the phase 2 benchmarks.

Comparison of Origin 2000 and Origin 3000 Using NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Turney, Raymond D.

2001-01-01

This report describes results of benchmark tests on the Origin 3000 system currently being installed at the NASA Ames National Advanced Supercomputing facility. This machine will ultimately contain 1024 R14K processors. The first part of the system, installed in November, 2000 and named mendel, is an Origin 3000 with 128 R12K processors. For comparison purposes, the tests were also run on lomax, an Origin 2000 with R12K processors. The BT, LU, and SP application benchmarks in the NAS Parallel Benchmark Suite and the kernel benchmark FT were chosen to determine system performance and measure the impact of changes on the machine as it evolves. Having been written to measure performance on Computational Fluid Dynamics applications, these benchmarks are assumed appropriate to represent the NAS workload. Since the NAS runs both message passing (MPI) and shared-memory, compiler directive type codes, both MPI and OpenMP versions of the benchmarks were used. The MPI versions used were the latest official release of the NAS Parallel Benchmarks, version 2.3. The OpenMP versiqns used were PBN3b2, a beta version that is in the process of being released. NPB 2.3 and PBN 3b2 are technically different benchmarks, and NPB results are not directly comparable to PBN results.

Benchmarking, benchmarks, or best practices? Applying quality improvement principles to decrease surgical turnaround time.

PubMed

Mitchell, L

1996-01-01

The processes of benchmarking, benchmark data comparative analysis, and study of best practices are distinctly different. The study of best practices is explained with an example based on the Arthur Andersen & Co. 1992 "Study of Best Practices in Ambulatory Surgery". The results of a national best practices study in ambulatory surgery were used to provide our quality improvement team with the goal of improving the turnaround time between surgical cases. The team used a seven-step quality improvement problem-solving process to improve the surgical turnaround time. The national benchmark for turnaround times between surgical cases in 1992 was 13.5 minutes. The initial turnaround time at St. Joseph's Medical Center was 19.9 minutes. After the team implemented solutions, the time was reduced to an average of 16.3 minutes, an 18% improvement. Cost-benefit analysis showed a potential enhanced revenue of approximately $300,000, or a potential savings of $10,119. Applying quality improvement principles to benchmarking, benchmarks, or best practices can improve process performance. Understanding which form of benchmarking the institution wishes to embark on will help focus a team and use appropriate resources. Communicating with professional organizations that have experience in benchmarking will save time and money and help achieve the desired results.

A benchmarking program to reduce red blood cell outdating: implementation, evaluation, and a conceptual framework.

PubMed

Barty, Rebecca L; Gagliardi, Kathleen; Owens, Wendy; Lauzon, Deborah; Scheuermann, Sheena; Liu, Yang; Wang, Grace; Pai, Menaka; Heddle, Nancy M

2015-07-01

Benchmarking is a quality improvement tool that compares an organization's performance to that of its peers for selected indicators, to improve practice. Processes to develop evidence-based benchmarks for red blood cell (RBC) outdating in Ontario hospitals, based on RBC hospital disposition data from Canadian Blood Services, have been previously reported. These benchmarks were implemented in 160 hospitals provincewide with a multifaceted approach, which included hospital education, inventory management tools and resources, summaries of best practice recommendations, recognition of high-performing sites, and audit tools on the Transfusion Ontario website (http://transfusionontario.org). In this study we describe the implementation process and the impact of the benchmarking program on RBC outdating. A conceptual framework for continuous quality improvement of a benchmarking program was also developed. The RBC outdating rate for all hospitals trended downward continuously from April 2006 to February 2012, irrespective of hospitals' transfusion rates or their distance from the blood supplier. The highest annual outdating rate was 2.82%, at the beginning of the observation period. Each year brought further reductions, with a nadir outdating rate of 1.02% achieved in 2011. The key elements of the successful benchmarking strategy included dynamic targets, a comprehensive and evidence-based implementation strategy, ongoing information sharing, and a robust data system to track information. The Ontario benchmarking program for RBC outdating resulted in continuous and sustained quality improvement. Our conceptual iterative framework for benchmarking provides a guide for institutions implementing a benchmarking program. © 2015 AABB.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munro, J.F.; Kristal, J.; Thompson, G.

The Office of Environmental Management is bringing Headquarters and the Field together to implement process improvements throughout the Complex through a systematic process of organizational learning called benchmarking. Simply stated, benchmarking is a process of continuously comparing and measuring practices, processes, or methodologies with those of other private and public organizations. The EM benchmarking program, which began as the result of a recommendation from Xerox Corporation, is building trust and removing barriers to performance enhancement across the DOE organization. The EM benchmarking program is designed to be field-centered with Headquarters providing facilitatory and integrative functions on an ``as needed`` basis.more » One of the main goals of the program is to assist Field Offices and their associated M&O/M&I contractors develop the capabilities to do benchmarking for themselves. In this regard, a central precept is that in order to realize tangible performance benefits, program managers and staff -- the ones closest to the work - must take ownership of the studies. This avoids the ``check the box`` mentality associated with some third party studies. This workshop will provide participants with a basic level of understanding why the EM benchmarking team was developed and the nature and scope of its mission. Participants will also begin to understand the types of study levels and the particular methodology the EM benchmarking team is using to conduct studies. The EM benchmarking team will also encourage discussion on ways that DOE (both Headquarters and the Field) can team with its M&O/M&I contractors to conduct additional benchmarking studies. This ``introduction to benchmarking`` is intended to create a desire to know more and a greater appreciation of how benchmarking processes could be creatively employed to enhance performance.« less

Using Benchmarking Techniques and the 2011 Maternity Practices Infant Nutrition and Care (mPINC) Survey to Improve Performance among Peer Groups across the United States

PubMed Central

Edwards, Roger A.; Dee, Deborah; Umer, Amna; Perrine, Cria G.; Shealy, Katherine R.; Grummer-Strawn, Laurence M.

2015-01-01

Background A substantial proportion of US maternity care facilities engage in practices that are not evidence-based and that interfere with breastfeeding. The CDC Survey of Maternity Practices in Infant Nutrition and Care (mPINC) showed significant variation in maternity practices among US states. Objective The purpose of this article is to use benchmarking techniques to identify states within relevant peer groups that were top performers on mPINC survey indicators related to breastfeeding support. Methods We used 11 indicators of breastfeeding-related maternity care from the 2011 mPINC survey and benchmarking techniques to organize and compare hospital-based maternity practices across the 50 states and Washington, DC. We created peer categories for benchmarking first by region (grouping states by West, Midwest, South, and Northeast) and then by size (grouping states by the number of maternity facilities and dividing each region into approximately equal halves based on the number of facilities). Results Thirty-four states had scores high enough to serve as benchmarks, and 32 states had scores low enough to reflect the lowest score gap from the benchmark on at least 1 indicator. No state served as the benchmark on more than 5 indicators and no state was furthest from the benchmark on more than 7 indicators. The small peer group benchmarks in the South, West, and Midwest were better than the large peer group benchmarks on 91%, 82%, and 36% of the indicators, respectively. In the West large, the Midwest large, the Midwest small, and the South large peer groups, 4–6 benchmarks showed that less than 50% of hospitals have ideal practice in all states. Conclusion The evaluation presents benchmarks for peer group state comparisons that provide potential and feasible targets for improvement. PMID:24394963

76 FR 58420 - Direct Investment Surveys: BE-12, Benchmark Survey of Foreign Direct Investment in the United States

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-21

...] RIN 0691-AA80 Direct Investment Surveys: BE-12, Benchmark Survey of Foreign Direct Investment in the... of Foreign Direct Investment in the United States. Benchmark surveys are conducted every five years; the prior survey covered 2007. The benchmark survey covers the universe of foreign direct investment...

Unstructured Adaptive (UA) NAS Parallel Benchmark. Version 1.0

NASA Technical Reports Server (NTRS)

Feng, Huiyu; VanderWijngaart, Rob; Biswas, Rupak; Mavriplis, Catherine

2004-01-01

We present a complete specification of a new benchmark for measuring the performance of modern computer systems when solving scientific problems featuring irregular, dynamic memory accesses. It complements the existing NAS Parallel Benchmark suite. The benchmark involves the solution of a stylized heat transfer problem in a cubic domain, discretized on an adaptively refined, unstructured mesh.

Operationalizing the Rubric: The Effect of Benchmark Selection on the Assessed Quality of Writing.

ERIC Educational Resources Information Center

Popp, Sharon E. Osborn; Ryan, Joseph M.; Thompson, Marilyn S.; Behrens, John T.

The purposes of this study were to investigate the role of benchmark writing samples in direct assessment of writing and to examine the consequences of differential benchmark selection with a common writing rubric. The influences of discourse and grade level were also examined within the context of differential benchmark selection. Raters scored…

A Causal-Comparative Study of the Affects of Benchmark Assessments on Middle Grades Science Achievement Scores

ERIC Educational Resources Information Center

Galloway, Melissa Ritchie

2016-01-01

The purpose of this causal comparative study was to test the theory of assessment that relates benchmark assessments to the Georgia middle grades science Criterion Referenced Competency Test (CRCT) percentages, controlling for schools who do not administer benchmark assessments versus schools who do administer benchmark assessments for all middle…

77 FR 58512 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Preliminary Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-21

... 2006 Decision Memorandum) at ``Benchmarks for Short-Term Financing.'' B. Benchmark for Long-Term Loans.... Subsidies Valuation Information A. Benchmarks for Short-Term Financing For those programs requiring the application of a won-denominated, short-term interest rate benchmark, in accordance with 19 CFR 351.505(a)(2...

Transaction Processing Performance Council (TPC): State of the Council 2010

NASA Astrophysics Data System (ADS)

Nambiar, Raghunath; Wakou, Nicholas; Carman, Forrest; Majdalany, Michael

The Transaction Processing Performance Council (TPC) is a non-profit corporation founded to define transaction processing and database benchmarks and to disseminate objective, verifiable performance data to the industry. Established in August 1988, the TPC has been integral in shaping the landscape of modern transaction processing and database benchmarks over the past twenty-two years. This paper provides an overview of the TPC's existing benchmark standards and specifications, introduces two new TPC benchmarks under development, and examines the TPC's active involvement in the early creation of additional future benchmarks.

Shift Verification and Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandya, Tara M.; Evans, Thomas M.; Davidson, Gregory G

2016-09-07

This documentation outlines the verification and validation of Shift for the Consortium for Advanced Simulation of Light Water Reactors (CASL). Five main types of problems were used for validation: small criticality benchmark problems; full-core reactor benchmarks for light water reactors; fixed-source coupled neutron-photon dosimetry benchmarks; depletion/burnup benchmarks; and full-core reactor performance benchmarks. We compared Shift results to measured data and other simulated Monte Carlo radiation transport code results, and found very good agreement in a variety of comparison measures. These include prediction of critical eigenvalue, radial and axial pin power distributions, rod worth, leakage spectra, and nuclide inventories over amore » burn cycle. Based on this validation of Shift, we are confident in Shift to provide reference results for CASL benchmarking.« less

Developing integrated benchmarks for DOE performance measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barancik, J.I.; Kramer, C.F.; Thode, Jr. H.C.

1992-09-30

The objectives of this task were to describe and evaluate selected existing sources of information on occupational safety and health with emphasis on hazard and exposure assessment, abatement, training, reporting, and control identifying for exposure and outcome in preparation for developing DOE performance benchmarks. Existing resources and methodologies were assessed for their potential use as practical performance benchmarks. Strengths and limitations of current data resources were identified. Guidelines were outlined for developing new or improved performance factors, which then could become the basis for selecting performance benchmarks. Data bases for non-DOE comparison populations were identified so that DOE performance couldmore » be assessed relative to non-DOE occupational and industrial groups. Systems approaches were described which can be used to link hazards and exposure, event occurrence, and adverse outcome factors, as needed to generate valid, reliable, and predictive performance benchmarks. Data bases were identified which contain information relevant to one or more performance assessment categories . A list of 72 potential performance benchmarks was prepared to illustrate the kinds of information that can be produced through a benchmark development program. Current information resources which may be used to develop potential performance benchmarks are limited. There is need to develop an occupational safety and health information and data system in DOE, which is capable of incorporating demonstrated and documented performance benchmarks prior to, or concurrent with the development of hardware and software. A key to the success of this systems approach is rigorous development and demonstration of performance benchmark equivalents to users of such data before system hardware and software commitments are institutionalized.« less

Benchmark Evaluation of HTR-PROTEUS Pebble Bed Experimental Program

DOE PAGES

Bess, John D.; Montierth, Leland; Köberl, Oliver; ...

2014-10-09

Benchmark models were developed to evaluate 11 critical core configurations of the HTR-PROTEUS pebble bed experimental program. Various additional reactor physics measurements were performed as part of this program; currently only a total of 37 absorber rod worth measurements have been evaluated as acceptable benchmark experiments for Cores 4, 9, and 10. Dominant uncertainties in the experimental keff for all core configurations come from uncertainties in the ²³⁵U enrichment of the fuel, impurities in the moderator pebbles, and the density and impurity content of the radial reflector. Calculations of k eff with MCNP5 and ENDF/B-VII.0 neutron nuclear data aremore » greater than the benchmark values but within 1% and also within the 3σ uncertainty, except for Core 4, which is the only randomly packed pebble configuration. Repeated calculations of k eff with MCNP6.1 and ENDF/B-VII.1 are lower than the benchmark values and within 1% (~3σ) except for Cores 5 and 9, which calculate lower than the benchmark eigenvalues within 4σ. The primary difference between the two nuclear data libraries is the adjustment of the absorption cross section of graphite. Simulations of the absorber rod worth measurements are within 3σ of the benchmark experiment values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments.« less

15 CFR 806.17 - Rules and regulations for BE-12, 2007 Benchmark Survey of Foreign Direct Investment in the United...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Benchmark Survey of Foreign Direct Investment in the United States. 806.17 Section 806.17 Commerce and... Survey of Foreign Direct Investment in the United States. A BE-12, Benchmark Survey of Foreign Direct... of the BE-12, 2007 Benchmark Survey of Foreign Direct Investment in the United States, contained in...

Using chemical benchmarking to determine the persistence of chemicals in a Swedish lake.

PubMed

Zou, Hongyan; Radke, Michael; Kierkegaard, Amelie; MacLeod, Matthew; McLachlan, Michael S

2015-02-03

It is challenging to measure the persistence of chemicals under field conditions. In this work, two approaches for measuring persistence in the field were compared: the chemical mass balance approach, and a novel chemical benchmarking approach. Ten pharmaceuticals, an X-ray contrast agent, and an artificial sweetener were studied in a Swedish lake. Acesulfame K was selected as a benchmark to quantify persistence using the chemical benchmarking approach. The 95% confidence intervals of the half-life for transformation in the lake system ranged from 780-5700 days for carbamazepine to <1-2 days for ketoprofen. The persistence estimates obtained using the benchmarking approach agreed well with those from the mass balance approach (1-21% difference), indicating that chemical benchmarking can be a valid and useful method to measure the persistence of chemicals under field conditions. Compared to the mass balance approach, the benchmarking approach partially or completely eliminates the need to quantify mass flow of chemicals, so it is particularly advantageous when the quantification of mass flow of chemicals is difficult. Furthermore, the benchmarking approach allows for ready comparison and ranking of the persistence of different chemicals.

Thought Experiment to Examine Benchmark Performance for Fusion Nuclear Data

NASA Astrophysics Data System (ADS)

Murata, Isao; Ohta, Masayuki; Kusaka, Sachie; Sato, Fuminobu; Miyamaru, Hiroyuki

2017-09-01

There are many benchmark experiments carried out so far with DT neutrons especially aiming at fusion reactor development. These integral experiments seemed vaguely to validate the nuclear data below 14 MeV. However, no precise studies exist now. The author's group thus started to examine how well benchmark experiments with DT neutrons can play a benchmarking role for energies below 14 MeV. Recently, as a next phase, to generalize the above discussion, the energy range was expanded to the entire region. In this study, thought experiments with finer energy bins have thus been conducted to discuss how to generally estimate performance of benchmark experiments. As a result of thought experiments with a point detector, the sensitivity for a discrepancy appearing in the benchmark analysis is "equally" due not only to contribution directly conveyed to the deterctor, but also due to indirect contribution of neutrons (named (A)) making neutrons conveying the contribution, indirect controbution of neutrons (B) making the neutrons (A) and so on. From this concept, it would become clear from a sensitivity analysis in advance how well and which energy nuclear data could be benchmarked with a benchmark experiment.

[The OPTIMISE study (Optimal Type 2 Diabetes Management Including Benchmarking and Standard Treatment]. Results for Luxembourg].

PubMed

Michel, G

2012-01-01

The OPTIMISE study (NCT00681850) has been run in six European countries, including Luxembourg, to prospectively assess the effect of benchmarking on the quality of primary care in patients with type 2 diabetes, using major modifiable vascular risk factors as critical quality indicators. Primary care centers treating type 2 diabetic patients were randomized to give standard care (control group) or standard care with feedback benchmarked against other centers in each country (benchmarking group). Primary endpoint was percentage of patients in the benchmarking group achieving pre-set targets of the critical quality indicators: glycated hemoglobin (HbAlc), systolic blood pressure (SBP) and low-density lipoprotein (LDL) cholesterol after 12 months follow-up. In Luxembourg, in the benchmarking group, more patients achieved target for SBP (40.2% vs. 20%) and for LDL-cholesterol (50.4% vs. 44.2%). 12.9% of patients in the benchmarking group met all three targets compared with patients in the control group (8.3%). In this randomized, controlled study, benchmarking was shown to be an effective tool for improving critical quality indicator targets, which are the principal modifiable vascular risk factors in diabetes type 2.

PDS: A Performance Database Server

DOE PAGES

Berry, Michael W.; Dongarra, Jack J.; Larose, Brian H.; ...

1994-01-01

The process of gathering, archiving, and distributing computer benchmark data is a cumbersome task usually performed by computer users and vendors with little coordination. Most important, there is no publicly available central depository of performance data for all ranges of machines from personal computers to supercomputers. We present an Internet-accessible performance database server (PDS) that can be used to extract current benchmark data and literature. As an extension to the X-Windows-based user interface (Xnetlib) to the Netlib archival system, PDS provides an on-line catalog of public domain computer benchmarks such as the LINPACK benchmark, Perfect benchmarks, and the NAS parallelmore » benchmarks. PDS does not reformat or present the benchmark data in any way that conflicts with the original methodology of any particular benchmark; it is thereby devoid of any subjective interpretations of machine performance. We believe that all branches (research laboratories, academia, and industry) of the general computing community can use this facility to archive performance metrics and make them readily available to the public. PDS can provide a more manageable approach to the development and support of a large dynamic database of published performance metrics.« less

Do Medicare Advantage Plans Minimize Costs? Investigating the Relationship Between Benchmarks, Costs, and Rebates.

PubMed

Zuckerman, Stephen; Skopec, Laura; Guterman, Stuart

2017-12-01

Medicare Advantage (MA), the program that allows people to receive their Medicare benefits through private health plans, uses a benchmark-and-bidding system to induce plans to provide benefits at lower costs. However, prior research suggests medical costs, profits, and other plan costs are not as low under this system as they might otherwise be. To examine how well the current system encourages MA plans to bid their lowest cost by examining the relationship between costs and bonuses (rebates) and the benchmarks Medicare uses in determining plan payments. Regression analysis using 2015 data for HMO and local PPO plans. Costs and rebates are higher for MA plans in areas with higher benchmarks, and plan costs vary less than benchmarks do. A one-dollar increase in benchmarks is associated with 32-cent-higher plan costs and a 52-cent-higher rebate, even when controlling for market and plan factors that can affect costs. This suggests the current benchmark-and-bidding system allows plans to bid higher than local input prices and other market conditions would seem to warrant. To incentivize MA plans to maximize efficiency and minimize costs, Medicare could change the way benchmarks are set or used.

The art and science of using routine outcome measurement in mental health benchmarking.

PubMed

McKay, Roderick; Coombs, Tim; Duerden, David

2014-02-01

To report and critique the application of routine outcome measurement data when benchmarking Australian mental health services. The experience of the authors as participants and facilitators of benchmarking activities is augmented by a review of the literature regarding mental health benchmarking in Australia. Although the published literature is limited, in practice, routine outcome measures, in particular the Health of the National Outcomes Scales (HoNOS) family of measures, are used in a variety of benchmarking activities. Use in exploring similarities and differences in consumers between services and the outcomes of care are illustrated. This requires the rigour of science in data management and interpretation, supplemented by the art that comes from clinical experience, a desire to reflect on clinical practice and the flexibility to use incomplete data to explore clinical practice. Routine outcome measurement data can be used in a variety of ways to support mental health benchmarking. With the increasing sophistication of information development in mental health, the opportunity to become involved in benchmarking will continue to increase. The techniques used during benchmarking and the insights gathered may prove useful to support reflection on practice by psychiatrists and other senior mental health clinicians.

Benchmarking Strategies for Measuring the Quality of Healthcare: Problems and Prospects

PubMed Central

Lovaglio, Pietro Giorgio

2012-01-01

Over the last few years, increasing attention has been directed toward the problems inherent to measuring the quality of healthcare and implementing benchmarking strategies. Besides offering accreditation and certification processes, recent approaches measure the performance of healthcare institutions in order to evaluate their effectiveness, defined as the capacity to provide treatment that modifies and improves the patient's state of health. This paper, dealing with hospital effectiveness, focuses on research methods for effectiveness analyses within a strategy comparing different healthcare institutions. The paper, after having introduced readers to the principle debates on benchmarking strategies, which depend on the perspective and type of indicators used, focuses on the methodological problems related to performing consistent benchmarking analyses. Particularly, statistical methods suitable for controlling case-mix, analyzing aggregate data, rare events, and continuous outcomes measured with error are examined. Specific challenges of benchmarking strategies, such as the risk of risk adjustment (case-mix fallacy, underreporting, risk of comparing noncomparable hospitals), selection bias, and possible strategies for the development of consistent benchmarking analyses, are discussed. Finally, to demonstrate the feasibility of the illustrated benchmarking strategies, an application focused on determining regional benchmarks for patient satisfaction (using 2009 Lombardy Region Patient Satisfaction Questionnaire) is proposed. PMID:22666140

Benchmarking strategies for measuring the quality of healthcare: problems and prospects.

PubMed

Lovaglio, Pietro Giorgio

2012-01-01

Over the last few years, increasing attention has been directed toward the problems inherent to measuring the quality of healthcare and implementing benchmarking strategies. Besides offering accreditation and certification processes, recent approaches measure the performance of healthcare institutions in order to evaluate their effectiveness, defined as the capacity to provide treatment that modifies and improves the patient's state of health. This paper, dealing with hospital effectiveness, focuses on research methods for effectiveness analyses within a strategy comparing different healthcare institutions. The paper, after having introduced readers to the principle debates on benchmarking strategies, which depend on the perspective and type of indicators used, focuses on the methodological problems related to performing consistent benchmarking analyses. Particularly, statistical methods suitable for controlling case-mix, analyzing aggregate data, rare events, and continuous outcomes measured with error are examined. Specific challenges of benchmarking strategies, such as the risk of risk adjustment (case-mix fallacy, underreporting, risk of comparing noncomparable hospitals), selection bias, and possible strategies for the development of consistent benchmarking analyses, are discussed. Finally, to demonstrate the feasibility of the illustrated benchmarking strategies, an application focused on determining regional benchmarks for patient satisfaction (using 2009 Lombardy Region Patient Satisfaction Questionnaire) is proposed.

Issues to consider in the derivation of water quality benchmarks for the protection of aquatic life.

PubMed

Schneider, Uwe

2014-01-01

While water quality benchmarks for the protection of aquatic life have been in use in some jurisdictions for several decades (USA, Canada, several European countries), more and more countries are now setting up their own national water quality benchmark development programs. In doing so, they either adopt an existing method from another jurisdiction, update on an existing approach, or develop their own new derivation method. Each approach has its own advantages and disadvantages, and many issues have to be addressed when setting up a water quality benchmark development program or when deriving a water quality benchmark. Each of these tasks requires a special expertise. They may seem simple, but are complex in their details. The intention of this paper was to provide some guidance for this process of water quality benchmark development on the program level, for the derivation methodology development, and in the actual benchmark derivation step, as well as to point out some issues (notably the inclusion of adapted populations and cryptic species and points to consider in the use of the species sensitivity distribution approach) and future opportunities (an international data repository and international collaboration in water quality benchmark development).

Evaluation of control strategies using an oxidation ditch benchmark.

PubMed

Abusam, A; Keesman, K J; Spanjers, H; van, Straten G; Meinema, K

2002-01-01

This paper presents validation and implementation results of a benchmark developed for a specific full-scale oxidation ditch wastewater treatment plant. A benchmark is a standard simulation procedure that can be used as a tool in evaluating various control strategies proposed for wastewater treatment plants. It is based on model and performance criteria development. Testing of this benchmark, by comparing benchmark predictions to real measurements of the electrical energy consumptions and amounts of disposed sludge for a specific oxidation ditch WWTP, has shown that it can (reasonably) be used for evaluating the performance of this WWTP. Subsequently, the validated benchmark was then used in evaluating some basic and advanced control strategies. Some of the interesting results obtained are the following: (i) influent flow splitting ratio, between the first and the fourth aerated compartments of the ditch, has no significant effect on the TN concentrations in the effluent, and (ii) for evaluation of long-term control strategies, future benchmarks need to be able to assess settlers' performance.

Benchmarking methods and data sets for ligand enrichment assessment in virtual screening.

PubMed

Xia, Jie; Tilahun, Ermias Lemma; Reid, Terry-Elinor; Zhang, Liangren; Wang, Xiang Simon

2015-01-01

Retrospective small-scale virtual screening (VS) based on benchmarking data sets has been widely used to estimate ligand enrichments of VS approaches in the prospective (i.e. real-world) efforts. However, the intrinsic differences of benchmarking sets to the real screening chemical libraries can cause biased assessment. Herein, we summarize the history of benchmarking methods as well as data sets and highlight three main types of biases found in benchmarking sets, i.e. "analogue bias", "artificial enrichment" and "false negative". In addition, we introduce our recent algorithm to build maximum-unbiased benchmarking sets applicable to both ligand-based and structure-based VS approaches, and its implementations to three important human histone deacetylases (HDACs) isoforms, i.e. HDAC1, HDAC6 and HDAC8. The leave-one-out cross-validation (LOO CV) demonstrates that the benchmarking sets built by our algorithm are maximum-unbiased as measured by property matching, ROC curves and AUCs. Copyright © 2014 Elsevier Inc. All rights reserved.

Benchmarking Methods and Data Sets for Ligand Enrichment Assessment in Virtual Screening

PubMed Central

Xia, Jie; Tilahun, Ermias Lemma; Reid, Terry-Elinor; Zhang, Liangren; Wang, Xiang Simon

2014-01-01

Retrospective small-scale virtual screening (VS) based on benchmarking data sets has been widely used to estimate ligand enrichments of VS approaches in the prospective (i.e. real-world) efforts. However, the intrinsic differences of benchmarking sets to the real screening chemical libraries can cause biased assessment. Herein, we summarize the history of benchmarking methods as well as data sets and highlight three main types of biases found in benchmarking sets, i.e. “analogue bias”, “artificial enrichment” and “false negative”. In addition, we introduced our recent algorithm to build maximum-unbiased benchmarking sets applicable to both ligand-based and structure-based VS approaches, and its implementations to three important human histone deacetylase (HDAC) isoforms, i.e. HDAC1, HDAC6 and HDAC8. The Leave-One-Out Cross-Validation (LOO CV) demonstrates that the benchmarking sets built by our algorithm are maximum-unbiased in terms of property matching, ROC curves and AUCs. PMID:25481478

Assessment of Static Delamination Propagation Capabilities in Commercial Finite Element Codes Using Benchmark Analysis

NASA Technical Reports Server (NTRS)

Orifici, Adrian C.; Krueger, Ronald

2010-01-01

With capabilities for simulating delamination growth in composite materials becoming available, the need for benchmarking and assessing these capabilities is critical. In this study, benchmark analyses were performed to assess the delamination propagation simulation capabilities of the VCCT implementations in Marc TM and MD NastranTM. Benchmark delamination growth results for Double Cantilever Beam, Single Leg Bending and End Notched Flexure specimens were generated using a numerical approach. This numerical approach was developed previously, and involves comparing results from a series of analyses at different delamination lengths to a single analysis with automatic crack propagation. Specimens were analyzed with three-dimensional and two-dimensional models, and compared with previous analyses using Abaqus . The results demonstrated that the VCCT implementation in Marc TM and MD Nastran(TradeMark) was capable of accurately replicating the benchmark delamination growth results and that the use of the numerical benchmarks offers advantages over benchmarking using experimental and analytical results.

Can data-driven benchmarks be used to set the goals of healthy people 2010?

PubMed Central

Allison, J; Kiefe, C I; Weissman, N W

1999-01-01

OBJECTIVES: Expert panels determined the public health goals of Healthy People 2000 subjectively. The present study examined whether data-driven benchmarks provide a better alternative. METHODS: We developed the "pared-mean" method to define from data the best achievable health care practices. We calculated the pared-mean benchmark for screening mammography from the 1994 National Health Interview Survey, using the metropolitan statistical area as the "provider" unit. Beginning with the best-performing provider and adding providers in descending sequence, we established the minimum provider subset that included at least 10% of all women surveyed on this question. The pared-mean benchmark is then the proportion of women in this subset who received mammography. RESULTS: The pared-mean benchmark for screening mammography was 71%, compared with the Healthy People 2000 goal of 60%. CONCLUSIONS: For Healthy People 2010, benchmarks derived from data reflecting the best available care provide viable alternatives to consensus-derived targets. We are currently pursuing additional refinements to the data-driven pared-mean benchmark approach. PMID:9987466

Benchmarking to improve the quality of cystic fibrosis care.

PubMed

Schechter, Michael S

2012-11-01

Benchmarking involves the ascertainment of healthcare programs with most favorable outcomes as a means to identify and spread effective strategies for delivery of care. The recent interest in the development of patient registries for patients with cystic fibrosis (CF) has been fueled in part by an interest in using them to facilitate benchmarking. This review summarizes reports of how benchmarking has been operationalized in attempts to improve CF care. Although certain goals of benchmarking can be accomplished with an exclusive focus on registry data analysis, benchmarking programs in Germany and the United States have supplemented these data analyses with exploratory interactions and discussions to better understand successful approaches to care and encourage their spread throughout the care network. Benchmarking allows the discovery and facilitates the spread of effective approaches to care. It provides a pragmatic alternative to traditional research methods such as randomized controlled trials, providing insights into methods that optimize delivery of care and allowing judgments about the relative effectiveness of different therapeutic approaches.

47 CFR 27.1221 - Interference protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... on height benchmarking, although the heights of antennas utilized are not restricted. (b) Height Benchmarking. Height benchmarking is defined for pairs of base stations, one in each of two proximate...

47 CFR 27.1221 - Interference protection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... on height benchmarking, although the heights of antennas utilized are not restricted. (b) Height benchmarking. Height benchmarking is defined for pairs of base stations, one in each of two proximate...

Summer 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendoza, Paul Michael

2016-08-31

The project goals seek to develop applications in order to automate MCNP criticality benchmark execution; create a dataset containing static benchmark information; combine MCNP output with benchmark information; and fit and visually represent data.

Method and system for benchmarking computers

DOEpatents

Gustafson, John L.

1993-09-14

A testing system and method for benchmarking computer systems. The system includes a store containing a scalable set of tasks to be performed to produce a solution in ever-increasing degrees of resolution as a larger number of the tasks are performed. A timing and control module allots to each computer a fixed benchmarking interval in which to perform the stored tasks. Means are provided for determining, after completion of the benchmarking interval, the degree of progress through the scalable set of tasks and for producing a benchmarking rating relating to the degree of progress for each computer.

Performance Evaluation of Supercomputers using HPCC and IMB Benchmarks

NASA Technical Reports Server (NTRS)

Saini, Subhash; Ciotti, Robert; Gunney, Brian T. N.; Spelce, Thomas E.; Koniges, Alice; Dossa, Don; Adamidis, Panagiotis; Rabenseifner, Rolf; Tiyyagura, Sunil R.; Mueller, Matthias;

Benchmarking Data Sets for the Evaluation of Virtual Ligand Screening Methods: Review and Perspectives.

PubMed

Lagarde, Nathalie; Zagury, Jean-François; Montes, Matthieu

2015-07-27

Virtual screening methods are commonly used nowadays in drug discovery processes. However, to ensure their reliability, they have to be carefully evaluated. The evaluation of these methods is often realized in a retrospective way, notably by studying the enrichment of benchmarking data sets. To this purpose, numerous benchmarking data sets were developed over the years, and the resulting improvements led to the availability of high quality benchmarking data sets. However, some points still have to be considered in the selection of the active compounds, decoys, and protein structures to obtain optimal benchmarking data sets.

Using Benchmarking To Influence Tuition and Fee Decisions.

ERIC Educational Resources Information Center

Hubbell, Loren W. Loomis; Massa, Robert J.; Lapovsky, Lucie

2002-01-01

Discusses the use of benchmarking in managing enrollment. Using a case study, illustrates how benchmarking can help administrators develop strategies for planning and implementing admissions and pricing practices. (EV)

15 CFR 806.16 - Rules and regulations for BE-10, Benchmark Survey of U.S. Direct Investment Abroad-2004.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., Benchmark Survey of U.S. Direct Investment Abroad-2004. 806.16 Section 806.16 Commerce and Foreign Trade... COMMERCE DIRECT INVESTMENT SURVEYS § 806.16 Rules and regulations for BE-10, Benchmark Survey of U.S. Direct Investment Abroad—2004. A BE-10, Benchmark Survey of U.S. Direct Investment Abroad will be...

FY 2002 Customer Satisfaction & Top 200 Users Survey Composite Report

DTIC Science & Technology

2002-11-01

Federal Government Benchmark 68.6% 71.1% DTIC Excels by +8.4 +11 *ACSI is the official service quality benchmark for the...care. § The American Customer Satisfaction Index (ACSI), the official service quality benchmark for the Federal Government, is currently 71.1%; DTIC...ACSI is the official service quality benchmark for the Federal GovernmentFig 1FY 20020Comparison of Customer Satisfaction (Customer Care

Full Chain Benchmarking for Open Architecture Airborne ISR Systems: A Case Study for GMTI Radar Applications

DTIC Science & Technology

2015-09-15

middleware implementations via a common object-oriented software hierarchy, with library -specific implementations of the five GMTI benchmark ...Full-Chain Benchmarking for Open Architecture Airborne ISR Systems A Case Study for GMTI Radar Applications Matthias Beebe, Matthew Alexander...time performance, effective benchmarks are necessary to ensure that an ARP system can meet the mission constraints and performance requirements of

Effects of benchmarking on the quality of type 2 diabetes care: results of the OPTIMISE (Optimal Type 2 Diabetes Management Including Benchmarking and Standard Treatment) study in Greece

PubMed Central

Tsimihodimos, Vasilis; Kostapanos, Michael S.; Moulis, Alexandros; Nikas, Nikos; Elisaf, Moses S.

2015-01-01

Objectives: To investigate the effect of benchmarking on the quality of type 2 diabetes (T2DM) care in Greece. Methods: The OPTIMISE (Optimal Type 2 Diabetes Management Including Benchmarking and Standard Treatment) study [ClinicalTrials.gov identifier: NCT00681850] was an international multicenter, prospective cohort study. It included physicians randomized 3:1 to either receive benchmarking for glycated hemoglobin (HbA1c), systolic blood pressure (SBP) and low-density lipoprotein cholesterol (LDL-C) treatment targets (benchmarking group) or not (control group). The proportions of patients achieving the targets of the above-mentioned parameters were compared between groups after 12 months of treatment. Also, the proportions of patients achieving those targets at 12 months were compared with baseline in the benchmarking group. Results: In the Greek region, the OPTIMISE study included 797 adults with T2DM (570 in the benchmarking group). At month 12 the proportion of patients within the predefined targets for SBP and LDL-C was greater in the benchmarking compared with the control group (50.6 versus 35.8%, and 45.3 versus 36.1%, respectively). However, these differences were not statistically significant. No difference between groups was noted in the percentage of patients achieving the predefined target for HbA1c. At month 12 the increase in the percentage of patients achieving all three targets was greater in the benchmarking (5.9–15.0%) than in the control group (2.7–8.1%). In the benchmarking group more patients were on target regarding SBP (50.6% versus 29.8%), LDL-C (45.3% versus 31.3%) and HbA1c (63.8% versus 51.2%) at 12 months compared with baseline (p < 0.001 for all comparisons). Conclusion: Benchmarking may comprise a promising tool for improving the quality of T2DM care. Nevertheless, target achievement rates of each, and of all three, quality indicators were suboptimal, indicating there are still unmet needs in the management of T2DM. PMID:26445642

SeSBench - An initiative to benchmark reactive transport models for environmental subsurface processes

NASA Astrophysics Data System (ADS)

Jacques, Diederik

2017-04-01

As soil functions are governed by a multitude of interacting hydrological, geochemical and biological processes, simulation tools coupling mathematical models for interacting processes are needed. Coupled reactive transport models are a typical example of such coupled tools mainly focusing on hydrological and geochemical coupling (see e.g. Steefel et al., 2015). Mathematical and numerical complexity for both the tool itself or of the specific conceptual model can increase rapidly. Therefore, numerical verification of such type of models is a prerequisite for guaranteeing reliability and confidence and qualifying simulation tools and approaches for any further model application. In 2011, a first SeSBench -Subsurface Environmental Simulation Benchmarking- workshop was held in Berkeley (USA) followed by four other ones. The objective is to benchmark subsurface environmental simulation models and methods with a current focus on reactive transport processes. The final outcome was a special issue in Computational Geosciences (2015, issue 3 - Reactive transport benchmarks for subsurface environmental simulation) with a collection of 11 benchmarks. Benchmarks, proposed by the participants of the workshops, should be relevant for environmental or geo-engineering applications; the latter were mostly related to radioactive waste disposal issues - excluding benchmarks defined for pure mathematical reasons. Another important feature is the tiered approach within a benchmark with the definition of a single principle problem and different sub problems. The latter typically benchmarked individual or simplified processes (e.g. inert solute transport, simplified geochemical conceptual model) or geometries (e.g. batch or one-dimensional, homogeneous). Finally, three codes should be involved into a benchmark. The SeSBench initiative contributes to confidence building for applying reactive transport codes. Furthermore, it illustrates the use of those type of models for different environmental and geo-engineering applications. SeSBench will organize new workshops to add new benchmarks in a new special issue. Steefel, C. I., et al. (2015). "Reactive transport codes for subsurface environmental simulation." Computational Geosciences 19: 445-478.

SU-E-T-148: Benchmarks and Pre-Treatment Reviews: A Study of Quality Assurance Effectiveness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowenstein, J; Nguyen, H; Roll, J

Purpose: To determine the impact benchmarks and pre-treatment reviews have on improving the quality of submitted clinical trial data. Methods: Benchmarks are used to evaluate a site’s ability to develop a treatment that meets a specific protocol’s treatment guidelines prior to placing their first patient on the protocol. A pre-treatment review is an actual patient placed on the protocol in which the dosimetry and contour volumes are evaluated to be per protocol guidelines prior to allowing the beginning of the treatment. A key component of these QA mechanisms is that sites are provided timely feedback to educate them on howmore » to plan per the protocol and prevent protocol deviations on patients accrued to a protocol. For both benchmarks and pre-treatment reviews a dose volume analysis (DVA) was performed using MIM softwareTM. For pre-treatment reviews a volume contour evaluation was also performed. Results: IROC Houston performed a QA effectiveness analysis of a protocol which required both benchmarks and pre-treatment reviews. In 70 percent of the patient cases submitted, the benchmark played an effective role in assuring that the pre-treatment review of the cases met protocol requirements. The 35 percent of sites failing the benchmark subsequently modified there planning technique to pass the benchmark before being allowed to submit a patient for pre-treatment review. However, in 30 percent of the submitted cases the pre-treatment review failed where the majority (71 percent) failed the DVA. 20 percent of sites submitting patients failed to correct their dose volume discrepancies indicated by the benchmark case. Conclusion: Benchmark cases and pre-treatment reviews can be an effective QA tool to educate sites on protocol guidelines and to minimize deviations. Without the benchmark cases it is possible that 65 percent of the cases undergoing a pre-treatment review would have failed to meet the protocols requirements.Support: U24-CA-180803.« less

SP2Bench: A SPARQL Performance Benchmark

NASA Astrophysics Data System (ADS)

Schmidt, Michael; Hornung, Thomas; Meier, Michael; Pinkel, Christoph; Lausen, Georg

A meaningful analysis and comparison of both existing storage schemes for RDF data and evaluation approaches for SPARQL queries necessitates a comprehensive and universal benchmark platform. We present SP2Bench, a publicly available, language-specific performance benchmark for the SPARQL query language. SP2Bench is settled in the DBLP scenario and comprises a data generator for creating arbitrarily large DBLP-like documents and a set of carefully designed benchmark queries. The generated documents mirror vital key characteristics and social-world distributions encountered in the original DBLP data set, while the queries implement meaningful requests on top of this data, covering a variety of SPARQL operator constellations and RDF access patterns. In this chapter, we discuss requirements and desiderata for SPARQL benchmarks and present the SP2Bench framework, including its data generator, benchmark queries and performance metrics.

Validation of tsunami inundation model TUNA-RP using OAR-PMEL-135 benchmark problem set

NASA Astrophysics Data System (ADS)

Koh, H. L.; Teh, S. Y.; Tan, W. K.; Kh'ng, X. Y.

2017-05-01

A standard set of benchmark problems, known as OAR-PMEL-135, is developed by the US National Tsunami Hazard Mitigation Program for tsunami inundation model validation. Any tsunami inundation model must be tested for its accuracy and capability using this standard set of benchmark problems before it can be gainfully used for inundation simulation. The authors have previously developed an in-house tsunami inundation model known as TUNA-RP. This inundation model solves the two-dimensional nonlinear shallow water equations coupled with a wet-dry moving boundary algorithm. This paper presents the validation of TUNA-RP against the solutions provided in the OAR-PMEL-135 benchmark problem set. This benchmark validation testing shows that TUNA-RP can indeed perform inundation simulation with accuracy consistent with that in the tested benchmark problem set.

Cost-Effectiveness Analysis of a Television Campaign to Promote Seasonal Influenza Vaccination Among the Elderly.

PubMed

Kim, Minchul; Yoo, Byung-Kwang

2015-07-01

The U.S. policy goals regarding influenza vaccination coverage rate among the elderly include the increase in the coverage rate and the elimination of disparities across racial/ethnic groups. To examine the potential effectiveness of a television (TV) campaign to increase seasonal influenza vaccination among the elderly. We estimated the incremental cost-effectiveness ratio (ICER, defined as incremental cost per additionally vaccinated Medicare individual) of a hypothetical nationwide TV campaign for influenza vaccination compared with no campaign. We measured the effectiveness of the nationwide TV campaign (advertised once a week at prime time for 30 seconds) during a 17-week influenza vaccination season among four racial/ethnic elderly groups (N=39 million): non-Hispanic white (W), non-Hispanic African American (AA), English-speaking Hispanic (EH), and Spanish-speaking Hispanic (SH). The hypothetical campaign cost was $5,960,000 (in 2012 US dollars). The estimated campaign effectiveness ranged from -1.1% (the SH group) to 1.42% (the W group), leading to an increased disparity in influenza vaccination among non-Hispanic white and non-Hispanic African American (W-AA) groups (0.6 percentage points), W-EH groups (0.1 percentage points), and W-SH groups (1.5 percentage points). The estimated ICER was $23.54 (95% confidence interval $14.21-$39.37) per additionally vaccinated Medicare elderly in a probabilistic analysis. Race/ethnicity-specific ICERs were lowest among the EH group ($22.27), followed by the W group ($22.47) and the AA group ($30.55). The nationwide TV campaign was concluded to be reasonably cost-effective compared with a benchmark intervention (with ICER $44.39 per vaccinated individual) of a school-located vaccination program. Break-even analyses estimated the maximum acceptable campaign cost to be $14,870,000, which was comparable to the benchmark ICER. The results could justify public expenditures on the implementation of a future nationwide TV campaign, which should include multilingual campaigns, for promoting seasonal influenza vaccination. Copyright © 2015. Published by Elsevier Inc.

Benchmark of Dynamic Electron Correlation Models for Seniority-Zero Wave Functions and Their Application to Thermochemistry.

PubMed

Boguslawski, Katharina; Tecmer, Paweł

2017-12-12

Wave functions restricted to electron-pair states are promising models to describe static/nondynamic electron correlation effects encountered, for instance, in bond-dissociation processes and transition-metal and actinide chemistry. To reach spectroscopic accuracy, however, the missing dynamic electron correlation effects that cannot be described by electron-pair states need to be included a posteriori. In this Article, we extend the previously presented perturbation theory models with an Antisymmetric Product of 1-reference orbital Geminal (AP1roG) reference function that allows us to describe both static/nondynamic and dynamic electron correlation effects. Specifically, our perturbation theory models combine a diagonal and off-diagonal zero-order Hamiltonian, a single-reference and multireference dual state, and different excitation operators used to construct the projection manifold. We benchmark all proposed models as well as an a posteriori Linearized Coupled Cluster correction on top of AP1roG against CR-CC(2,3) reference data for reaction energies of several closed-shell molecules that are extrapolated to the basis set limit. Moreover, we test the performance of our new methods for multiple bond breaking processes in the homonuclear N 2 , C 2 , and F 2 dimers as well as the heteronuclear BN, CO, and CN + dimers against MRCI-SD, MRCI-SD+Q, and CR-CC(2,3) reference data. Our numerical results indicate that the best performance is obtained from a Linearized Coupled Cluster correction as well as second-order perturbation theory corrections employing a diagonal and off-diagonal zero-order Hamiltonian and a single-determinant dual state. These dynamic corrections on top of AP1roG provide substantial improvements for binding energies and spectroscopic properties obtained with the AP1roG approach, while allowing us to approach chemical accuracy for reaction energies involving closed-shell species.

3-D kinematics analysis of surface ruptures on an active creeping fault at Chihshang, Eastern Taiwan

NASA Astrophysics Data System (ADS)

Lee, J.; Angelier, J.; Chen, H.; Chu, H.; Hu, J.

2003-12-01

The Chihshang fault is one of the most active segments of the Longitudinal Valley Fault, the plate suture between the converging Philippine and Eurasian plates. A destructive earthquake of M 7.1 with substantial surface scarps resulted from rupturing of the Chihshang fault in 1951. From that on, no big earthquake greater than M 5.5 occurred in this area. Instead, the Chihshang fault reveals a creeping behavior at a rapid rate of about 20 mm/yr at least during the past 20 years. The surface breaks of the creeping Chihshang fault can be observed at the several places. A typical feature is reverse-fault-like fractures on the retaining wall. We deployed small geodetic networks across the fault zone at five sites. Each network comprises of 5 to 15 benchmarks. Trilateration measurements including angles and distances as well as leveling among the benchmarks have been carried out on an annual basis or twice a year since 1998. Compared to previous other measurements which have shown the first order creep rate for the entire fault zone, the present geodetic data provides the detailed information of the surface movements across the fault zone which usually composed of more than one fault strands and folds structures. According to our data from the local geodetic networks, we are able to reconstruct the 3-D kinematics of surface deformation across the Chihshang fault zone. Multiple fault strands are common along the Chihshang fault. Oblique shortening occurred at all sites and was characterized by a combination of thrusts, backthrust and surface warps. Strike-slip motion can also be distinguished on some fault strands. It is worth to note that the cultural feature, such as concrete basement of strong resistance, sometimes acted as deflection of surface ruptures. It should be taken into consideration for mitigation against seismic hazards.

Benchmark problems for numerical implementations of phase field models

DOE PAGES

Jokisaari, A. M.; Voorhees, P. W.; Guyer, J. E.; ...

2016-10-01

Here, we present the first set of benchmark problems for phase field models that are being developed by the Center for Hierarchical Materials Design (CHiMaD) and the National Institute of Standards and Technology (NIST). While many scientific research areas use a limited set of well-established software, the growing phase field community continues to develop a wide variety of codes and lacks benchmark problems to consistently evaluate the numerical performance of new implementations. Phase field modeling has become significantly more popular as computational power has increased and is now becoming mainstream, driving the need for benchmark problems to validate and verifymore » new implementations. We follow the example set by the micromagnetics community to develop an evolving set of benchmark problems that test the usability, computational resources, numerical capabilities and physical scope of phase field simulation codes. In this paper, we propose two benchmark problems that cover the physics of solute diffusion and growth and coarsening of a second phase via a simple spinodal decomposition model and a more complex Ostwald ripening model. We demonstrate the utility of benchmark problems by comparing the results of simulations performed with two different adaptive time stepping techniques, and we discuss the needs of future benchmark problems. The development of benchmark problems will enable the results of quantitative phase field models to be confidently incorporated into integrated computational materials science and engineering (ICME), an important goal of the Materials Genome Initiative.« less

Computational Chemistry Comparison and Benchmark Database

National Institute of Standards and Technology Data Gateway

SRD 101 NIST Computational Chemistry Comparison and Benchmark Database (Web, free access)   The NIST Computational Chemistry Comparison and Benchmark Database is a collection of experimental and ab initio thermochemical properties for a selected set of molecules. The goals are to provide a benchmark set of molecules for the evaluation of ab initio computational methods and allow the comparison between different ab initio computational methods for the prediction of thermochemical properties.

A Methodology for Benchmarking Relational Database Machines,

DTIC Science & Technology

1984-01-01

user benchmarks is to compare the multiple users to the best-case performance The data for each query classification coll and the performance...called a benchmark. The term benchmark originates from the markers used by sur - veyors in establishing common reference points for their measure...formatted databases. In order to further simplify the problem, we restrict our study to those DBMs which support the relational model. A sur - vey

Benchmarking and the laboratory

PubMed Central

Galloway, M; Nadin, L

2001-01-01

This article describes how benchmarking can be used to assess laboratory performance. Two benchmarking schemes are reviewed, the Clinical Benchmarking Company's Pathology Report and the College of American Pathologists' Q-Probes scheme. The Clinical Benchmarking Company's Pathology Report is undertaken by staff based in the clinical management unit, Keele University with appropriate input from the professional organisations within pathology. Five annual reports have now been completed. Each report is a detailed analysis of 10 areas of laboratory performance. In this review, particular attention is focused on the areas of quality, productivity, variation in clinical practice, skill mix, and working hours. The Q-Probes scheme is part of the College of American Pathologists programme in studies of quality assurance. The Q-Probes scheme and its applicability to pathology in the UK is illustrated by reviewing two recent Q-Probe studies: routine outpatient test turnaround time and outpatient test order accuracy. The Q-Probes scheme is somewhat limited by the small number of UK laboratories that have participated. In conclusion, as a result of the government's policy in the UK, benchmarking is here to stay. Benchmarking schemes described in this article are one way in which pathologists can demonstrate that they are providing a cost effective and high quality service. Key Words: benchmarking • pathology PMID:11477112

Benchmarking: your performance measurement and improvement tool.

PubMed

Senn, G F

2000-01-01

Many respected professional healthcare organizations and societies today are seeking to establish data-driven performance measurement strategies such as benchmarking. Clinicians are, however, resistant to "benchmarking" that is based on financial data alone, concerned that it may be adverse to the patients' best interests. Benchmarking of clinical procedures that uses physician's codes such as Current Procedural Terminology (CPTs) has greater credibility with practitioners. Better Performers, organizations that can perform procedures successfully at lower cost and in less time, become the "benchmark" against which other organizations can measure themselves. The Better Performers' strategies can be adopted by other facilities to save time or money while maintaining quality patient care.

A Field-Based Aquatic Life Benchmark for Conductivity in ...

EPA Pesticide Factsheets

EPA announced the availability of the final report, A Field-Based Aquatic Life Benchmark for Conductivity in Central Appalachian Streams. This report describes a method to characterize the relationship between the extirpation (the effective extinction) of invertebrate genera and salinity (measured as conductivity) and from that relationship derives a freshwater aquatic life benchmark. This benchmark of 300 µS/cm may be applied to waters in Appalachian streams that are dominated by calcium and magnesium salts of sulfate and bicarbonate at circum-neutral to mildly alkaline pH. This report provides scientific evidence for a conductivity benchmark in a specific region rather than for the entire United States.

A One-group, One-dimensional Transport Benchmark in Cylindrical Geometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barry Ganapol; Abderrafi M. Ougouag

A 1-D, 1-group computational benchmark in cylndrical geometry is described. This neutron transport benchmark is useful for evaluating reactor concepts that possess azimuthal symmetry such as a pebble-bed reactor.

Using Spoken Language Benchmarks to Characterize the Expressive Language Skills of Young Children With Autism Spectrum Disorders

PubMed Central

Weismer, Susan Ellis

2015-01-01

Purpose Spoken language benchmarks proposed by Tager-Flusberg et al. (2009) were used to characterize communication profiles of toddlers with autism spectrum disorders and to investigate if there were differences in variables hypothesized to influence language development at different benchmark levels. Method The communication abilities of a large sample of toddlers with autism spectrum disorders (N = 105) were characterized in terms of spoken language benchmarks. The toddlers were grouped according to these benchmarks to investigate whether there were differences in selected variables across benchmark groups at a mean age of 2.5 years. Results The majority of children in the sample presented with uneven communication profiles with relative strengths in phonology and significant weaknesses in pragmatics. When children were grouped according to one expressive language domain, across-group differences were observed in response to joint attention and gestures but not cognition or restricted and repetitive behaviors. Conclusion The spoken language benchmarks are useful for characterizing early communication profiles and investigating features that influence expressive language growth. PMID:26254475

Toxicological benchmarks for screening potential contaminants of concern for effects on soil and litter invertebrates and heterotrophic process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Will, M.E.; Suter, G.W. II

1994-09-01

One of the initial stages in ecological risk assessments for hazardous waste sites is the screening of contaminants to determine which of them are worthy of further consideration as {open_quotes}contaminants of potential concern.{close_quotes} This process is termed {open_quotes}contaminant screening.{close_quotes} It is performed by comparing measured ambient concentrations of chemicals to benchmark concentrations. Currently, no standard benchmark concentrations exist for assessing contaminants in soil with respect to their toxicity to soil- and litter-dwelling invertebrates, including earthworms, other micro- and macroinvertebrates, or heterotrophic bacteria and fungi. This report presents a standard method for deriving benchmarks for this purpose, sets of data concerningmore » effects of chemicals in soil on invertebrates and soil microbial processes, and benchmarks for chemicals potentially associated with United States Department of Energy sites. In addition, literature describing the experiments from which data were drawn for benchmark derivation. Chemicals that are found in soil at concentrations exceeding both the benchmarks and the background concentration for the soil type should be considered contaminants of potential concern.« less

MoMaS reactive transport benchmark using PFLOTRAN

NASA Astrophysics Data System (ADS)

Park, H.

2017-12-01

MoMaS benchmark was developed to enhance numerical simulation capability for reactive transport modeling in porous media. The benchmark was published in late September of 2009; it is not taken from a real chemical system, but realistic and numerically challenging tests. PFLOTRAN is a state-of-art massively parallel subsurface flow and reactive transport code that is being used in multiple nuclear waste repository projects at Sandia National Laboratories including Waste Isolation Pilot Plant and Used Fuel Disposition. MoMaS benchmark has three independent tests with easy, medium, and hard chemical complexity. This paper demonstrates how PFLOTRAN is applied to this benchmark exercise and shows results of the easy benchmark test case which includes mixing of aqueous components and surface complexation. Surface complexations consist of monodentate and bidentate reactions which introduces difficulty in defining selectivity coefficient if the reaction applies to a bulk reference volume. The selectivity coefficient becomes porosity dependent for bidentate reaction in heterogeneous porous media. The benchmark is solved by PFLOTRAN with minimal modification to address the issue and unit conversions were made properly to suit PFLOTRAN.

Test One to Test Many: A Unified Approach to Quantum Benchmarks

NASA Astrophysics Data System (ADS)

Bai, Ge; Chiribella, Giulio

2018-04-01

Quantum benchmarks are routinely used to validate the experimental demonstration of quantum information protocols. Many relevant protocols, however, involve an infinite set of input states, of which only a finite subset can be used to test the quality of the implementation. This is a problem, because the benchmark for the finitely many states used in the test can be higher than the original benchmark calculated for infinitely many states. This situation arises in the teleportation and storage of coherent states, for which the benchmark of 50% fidelity is commonly used in experiments, although finite sets of coherent states normally lead to higher benchmarks. Here, we show that the average fidelity over all coherent states can be indirectly probed with a single setup, requiring only two-mode squeezing, a 50-50 beam splitter, and homodyne detection. Our setup enables a rigorous experimental validation of quantum teleportation, storage, amplification, attenuation, and purification of noisy coherent states. More generally, we prove that every quantum benchmark can be tested by preparing a single entangled state and measuring a single observable.

Benchmarking and Its Relevance to the Library and Information Sector. Interim Findings of "Best Practice Benchmarking in the Library and Information Sector," a British Library Research and Development Department Project.

ERIC Educational Resources Information Center

Kinnell, Margaret; Garrod, Penny

This British Library Research and Development Department study assesses current activities and attitudes toward quality management in library and information services (LIS) in the academic sector as well as the commercial/industrial sector. Definitions and types of benchmarking are described, and the relevance of benchmarking to LIS is evaluated.…

Benchmarks for Evaluation of Distributed Denial of Service (DDOS)

DTIC Science & Technology

2008-01-01

publications: [1] E. Arikan , Attack Profiling for DDoS Benchmarks, MS Thesis, University of Delaware, August 2006. [2] J. Mirkovic, A. Hussain, B. Wilson...Sigmetrics 2007, June 2007 [5] J. Mirkovic, E. Arikan , S. Wei, S. Fahmy, R. Thomas, and P. Reiher Benchmarks for DDoS Defense Evaluation, Proceedings of the...Security Experimentation, June 2006. [9] J. Mirkovic, E. Arikan , S. Wei, S. Fahmy, R. Thomas, P. Reiher, Benchmarks for DDoS Defense Evaluation

OWL2 benchmarking for the evaluation of knowledge based systems.

PubMed

Khan, Sher Afgun; Qadir, Muhammad Abdul; Abbas, Muhammad Azeem; Afzal, Muhammad Tanvir

2017-01-01

OWL2 semantics are becoming increasingly popular for the real domain applications like Gene engineering and health MIS. The present work identifies the research gap that negligible attention has been paid to the performance evaluation of Knowledge Base Systems (KBS) using OWL2 semantics. To fulfil this identified research gap, an OWL2 benchmark for the evaluation of KBS is proposed. The proposed benchmark addresses the foundational blocks of an ontology benchmark i.e. data schema, workload and performance metrics. The proposed benchmark is tested on memory based, file based, relational database and graph based KBS for performance and scalability measures. The results show that the proposed benchmark is able to evaluate the behaviour of different state of the art KBS on OWL2 semantics. On the basis of the results, the end users (i.e. domain expert) would be able to select a suitable KBS appropriate for his domain.

FireHose Streaming Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karl Anderson, Steve Plimpton

2015-01-27

The FireHose Streaming Benchmarks are a suite of stream-processing benchmarks defined to enable comparison of streaming software and hardware, both quantitatively vis-a-vis the rate at which they can process data, and qualitatively by judging the effort involved to implement and run the benchmarks. Each benchmark has two parts. The first is a generator which produces and outputs datums at a high rate in a specific format. The second is an analytic which reads the stream of datums and is required to perform a well-defined calculation on the collection of datums, typically to find anomalous datums that have been created inmore » the stream by the generator. The FireHose suite provides code for the generators, sample code for the analytics (which users are free to re-implement in their own custom frameworks), and a precise definition of each benchmark calculation.« less

A new numerical benchmark of a freshwater lens

NASA Astrophysics Data System (ADS)

Stoeckl, L.; Walther, M.; Graf, T.

2016-04-01

A numerical benchmark for 2-D variable-density flow and solute transport in a freshwater lens is presented. The benchmark is based on results of laboratory experiments conducted by Stoeckl and Houben (2012) using a sand tank on the meter scale. This benchmark describes the formation and degradation of a freshwater lens over time as it can be found under real-world islands. An error analysis gave the appropriate spatial and temporal discretization of 1 mm and 8.64 s, respectively. The calibrated parameter set was obtained using the parameter estimation tool PEST. Comparing density-coupled and density-uncoupled results showed that the freshwater-saltwater interface position is strongly dependent on density differences. A benchmark that adequately represents saltwater intrusion and that includes realistic features of coastal aquifers or freshwater lenses was lacking. This new benchmark was thus developed and is demonstrated to be suitable to test variable-density groundwater models applied to saltwater intrusion investigations.

COMPETITIVE BIDDING IN MEDICARE ADVANTAGE: EFFECT OF BENCHMARK CHANGES ON PLAN BIDS

PubMed Central

Song, Zirui; Landrum, Mary Beth; Chernew, Michael E.

2013-01-01

Bidding has been proposed to replace or complement the administered prices in Medicare pays to hospitals and health plans. In 2006, the Medicare Advantage program implemented a competitive bidding system to determine plan payments. In perfectly competitive models, plans bid their costs and thus bids are insensitive to the benchmark. Under many other models of competition, bids respond to changes in the benchmark. We conceptualize the bidding system and use an instrumental variable approach to study the effect of benchmark changes on bids. We use 2006–2010 plan payment data from the Centers for Medicare and Medicaid Services, published county benchmarks, actual realized fee-for-service costs, and Medicare Advantage enrollment. We find that a $1 increase in the benchmark leads to about a $0.53 increase in bids, suggesting that plans in the Medicare Advantage market have meaningful market power. PMID:24308881

Competitive bidding in Medicare Advantage: effect of benchmark changes on plan bids.

PubMed

Song, Zirui; Landrum, Mary Beth; Chernew, Michael E

2013-12-01

Bidding has been proposed to replace or complement the administered prices that Medicare pays to hospitals and health plans. In 2006, the Medicare Advantage program implemented a competitive bidding system to determine plan payments. In perfectly competitive models, plans bid their costs and thus bids are insensitive to the benchmark. Under many other models of competition, bids respond to changes in the benchmark. We conceptualize the bidding system and use an instrumental variable approach to study the effect of benchmark changes on bids. We use 2006-2010 plan payment data from the Centers for Medicare and Medicaid Services, published county benchmarks, actual realized fee-for-service costs, and Medicare Advantage enrollment. We find that a $1 increase in the benchmark leads to about a $0.53 increase in bids, suggesting that plans in the Medicare Advantage market have meaningful market power. Copyright © 2013 Elsevier B.V. All rights reserved.

Groundwater-quality data in the North San Francisco Bay Shallow Aquifer study unit, 2012: results from the California GAMA Program

USGS Publications Warehouse

Bennett, George L.; Fram, Miranda S.

2014-01-01

Results for constituents with non-regulatory benchmarks set for aesthetic concerns from the grid wells showed that iron concentrations greater than the CDPH secondary maximum contaminant level (SMCL-CA) of 300 μg/L were detected in 13 grid wells. Chloride was detected at a concentration greater than the SMCL-CA recommended benchmark of 250 mg/L in two grid wells. Sulfate concentrations greater than the SMCL-CA recommended benchmark of 250 mg/L were measured in two grid wells, and the concentration in one of these wells was also greater than the SMCL-CA upper benchmark of 500 mg/L. TDS concentrations greater than the SMCL-CA recommended benchmark of 500 mg/L were measured in 15 grid wells, and concentrations in 4 of these wells were also greater than the SMCL-CA upper benchmark of 1,000 mg/L.

Benchmarking of HEU Mental Annuli Critical Assemblies with Internally Reflected Graphite Cylinder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiaobo, Liu; Bess, John D.; Marshall, Margaret A.

Three experimental configurations of critical assemblies, performed in 1963 at the Oak Ridge Critical Experiment Facility, which are assembled using three different diameter HEU annuli (15-9 inches, 15-7 inches and 13-7 inches) metal annuli with internally reflected graphite cylinder are evaluated and benchmarked. The experimental uncertainties which are 0.00055, 0.00055 and 0.00055 respectively, and biases to the detailed benchmark models which are -0.00179, -0.00189 and -0.00114 respectively, were determined, and the experimental benchmark keff results were obtained for both detailed and simplified model. The calculation results for both detailed and simplified models using MCNP6-1.0 and ENDF VII.1 agree well tomore » the benchmark experimental results with a difference of less than 0.2%. These are acceptable benchmark experiments for inclusion in the ICSBEP Handbook.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marck, Steven C. van der, E-mail: vandermarck@nrg.eu

Recent releases of three major world nuclear reaction data libraries, ENDF/B-VII.1, JENDL-4.0, and JEFF-3.1.1, have been tested extensively using benchmark calculations. The calculations were performed with the latest release of the continuous energy Monte Carlo neutronics code MCNP, i.e. MCNP6. Three types of benchmarks were used, viz. criticality safety benchmarks, (fusion) shielding benchmarks, and reference systems for which the effective delayed neutron fraction is reported. For criticality safety, more than 2000 benchmarks from the International Handbook of Criticality Safety Benchmark Experiments were used. Benchmarks from all categories were used, ranging from low-enriched uranium, compound fuel, thermal spectrum ones (LEU-COMP-THERM), tomore » mixed uranium-plutonium, metallic fuel, fast spectrum ones (MIX-MET-FAST). For fusion shielding many benchmarks were based on IAEA specifications for the Oktavian experiments (for Al, Co, Cr, Cu, LiF, Mn, Mo, Si, Ti, W, Zr), Fusion Neutronics Source in Japan (for Be, C, N, O, Fe, Pb), and Pulsed Sphere experiments at Lawrence Livermore National Laboratory (for {sup 6}Li, {sup 7}Li, Be, C, N, O, Mg, Al, Ti, Fe, Pb, D2O, H2O, concrete, polyethylene and teflon). The new functionality in MCNP6 to calculate the effective delayed neutron fraction was tested by comparison with more than thirty measurements in widely varying systems. Among these were measurements in the Tank Critical Assembly (TCA in Japan) and IPEN/MB-01 (Brazil), both with a thermal spectrum, two cores in Masurca (France) and three cores in the Fast Critical Assembly (FCA, Japan), all with fast spectra. The performance of the three libraries, in combination with MCNP6, is shown to be good. The results for the LEU-COMP-THERM category are on average very close to the benchmark value. Also for most other categories the results are satisfactory. Deviations from the benchmark values do occur in certain benchmark series, or in isolated cases within benchmark series. Such instances can often be related to nuclear data for specific non-fissile elements, such as C, Fe, or Gd. Indications are that the intermediate and mixed spectrum cases are less well described. The results for the shielding benchmarks are generally good, with very similar results for the three libraries in the majority of cases. Nevertheless there are, in certain cases, strong deviations between calculated and benchmark values, such as for Co and Mg. Also, the results show discrepancies at certain energies or angles for e.g. C, N, O, Mo, and W. The functionality of MCNP6 to calculate the effective delayed neutron fraction yields very good results for all three libraries.« less

EPA's Benchmark Dose Modeling Software

EPA Science Inventory

The EPA developed the Benchmark Dose Software (BMDS) as a tool to help Agency risk assessors facilitate applying benchmark dose (BMD) method’s to EPA’s human health risk assessment (HHRA) documents. The application of BMD methods overcomes many well know limitations ...

Using benchmarks for radiation testing of microprocessors and FPGAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quinn, Heather; Robinson, William H.; Rech, Paolo

Performance benchmarks have been used over the years to compare different systems. These benchmarks can be useful for researchers trying to determine how changes to the technology, architecture, or compiler affect the system's performance. No such standard exists for systems deployed into high radiation environments, making it difficult to assess whether changes in the fabrication process, circuitry, architecture, or software affect reliability or radiation sensitivity. In this paper, we propose a benchmark suite for high-reliability systems that is designed for field-programmable gate arrays and microprocessors. As a result, we describe the development process and report neutron test data for themore » hardware and software benchmarks.« less

Using benchmarks for radiation testing of microprocessors and FPGAs

DOE PAGES

Quinn, Heather; Robinson, William H.; Rech, Paolo; ...

2015-12-17

Performance benchmarks have been used over the years to compare different systems. These benchmarks can be useful for researchers trying to determine how changes to the technology, architecture, or compiler affect the system's performance. No such standard exists for systems deployed into high radiation environments, making it difficult to assess whether changes in the fabrication process, circuitry, architecture, or software affect reliability or radiation sensitivity. In this paper, we propose a benchmark suite for high-reliability systems that is designed for field-programmable gate arrays and microprocessors. As a result, we describe the development process and report neutron test data for themore » hardware and software benchmarks.« less

Benchmarking biology research organizations using a new, dedicated tool.

PubMed

van Harten, Willem H; van Bokhorst, Leonard; van Luenen, Henri G A M

2010-02-01

International competition forces fundamental research organizations to assess their relative performance. We present a benchmark tool for scientific research organizations where, contrary to existing models, the group leader is placed in a central position within the organization. We used it in a pilot benchmark study involving six research institutions. Our study shows that data collection and data comparison based on this new tool can be achieved. It proved possible to compare relative performance and organizational characteristics and to generate suggestions for improvement for most participants. However, strict definitions of the parameters used for the benchmark and a thorough insight into the organization of each of the benchmark partners is required to produce comparable data and draw firm conclusions.

Constrained exceptional supersymmetric standard model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Athron, P.; King, S. F.; Miller, D. J.

2009-08-01

We propose and study a constrained version of the exceptional supersymmetric standard model (E{sub 6}SSM), which we call the cE{sub 6}SSM, based on a universal high energy scalar mass m{sub 0}, trilinear scalar coupling A{sub 0} and gaugino mass M{sub 1/2}. We derive the renormalization group (RG) Equations for the cE{sub 6}SSM, including the extra U(1){sub N} gauge factor and the low-energy matter content involving three 27 representations of E{sub 6}. We perform a numerical RG analysis for the cE{sub 6}SSM, imposing the usual low-energy experimental constraints and successful electroweak symmetry breaking. Our analysis reveals that the sparticle spectrum ofmore » the cE{sub 6}SSM involves a light gluino, two light neutralinos, and a light chargino. Furthermore, although the squarks, sleptons, and Z{sup '} boson are typically heavy, the exotic quarks and squarks can also be relatively light. We finally specify a set of benchmark points, which correspond to particle spectra, production modes, and decay patterns peculiar to the cE{sub 6}SSM, altogether leading to spectacular new physics signals at the Large Hadron Collider.« less

CP violation in heavy MSSM Higgs scenarios

DOE PAGES

Carena, M.; Ellis, J.; Lee, J. S.; ...

2016-02-18

We introduce and explore new heavy Higgs scenarios in the Minimal Supersymmetric Standard Model (MSSM) with explicit CP violation, which have important phenomenological implications that may be testable at the LHC. For soft supersymmetry-breaking scales M S above a few TeV and a charged Higgs boson mass M H+ above a few hundred GeV, new physics effects including those from explicit CP violation decouple from the light Higgs boson sector. However, such effects can significantly alter the phenomenology of the heavy Higgs bosons while still being consistent with constraints from low-energy observables, for instance electric dipole moments. To consider scenariosmore » with a charged Higgs boson much heavier than the Standard Model (SM) particles but much lighter than the supersymmetric particles, we revisit previous calculations of the MSSM Higgs sector. We compute the Higgs boson masses in the presence of CP violating phases, implementing improved matching and renormalization-group (RG) effects, as well as two-loop RG effects from the effective two-Higgs Doublet Model (2HDM) scale M H± to the scale M S. Here, we illustrate the possibility of non-decoupling CP-violating effects in the heavy Higgs sector using new benchmark scenarios named.« less

Correlation matrix renormalization theory for correlated-electron materials with application to the crystalline phases of atomic hydrogen

DOE PAGES

Zhao, Xin; Liu, Jun; Yao, Yong-Xin; ...

2018-01-23

Developing accurate and computationally efficient methods to calculate the electronic structure and total energy of correlated-electron materials has been a very challenging task in condensed matter physics and materials science. Recently, we have developed a correlation matrix renormalization (CMR) method which does not assume any empirical Coulomb interaction U parameters and does not have double counting problems in the ground-state total energy calculation. The CMR method has been demonstrated to be accurate in describing both the bonding and bond breaking behaviors of molecules. In this study, we extend the CMR method to the treatment of electron correlations in periodic solidmore » systems. By using a linear hydrogen chain as a benchmark system, we show that the results from the CMR method compare very well with those obtained recently by accurate quantum Monte Carlo (QMC) calculations. We also study the equation of states of three-dimensional crystalline phases of atomic hydrogen. We show that the results from the CMR method agree much better with the available QMC data in comparison with those from density functional theory and Hartree-Fock calculations.« less

Generalization of fewest-switches surface hopping for coherences

NASA Astrophysics Data System (ADS)

Tempelaar, Roel; Reichman, David R.

2018-03-01

Fewest-switches surface hopping (FSSH) is perhaps the most widely used mixed quantum-classical approach for the modeling of non-adiabatic processes, but its original formulation is restricted to (adiabatic) population terms of the quantum density matrix, leaving its implementations with an inconsistency in the treatment of populations and coherences. In this article, we propose a generalization of FSSH that treats both coherence and population terms on equal footing and which formally reduces to the conventional FSSH algorithm for the case of populations. This approach, coherent fewest-switches surface hopping (C-FSSH), employs a decoupling of population relaxation and pure dephasing and involves two replicas of the classical trajectories interacting with two active surfaces. Through extensive benchmark calculations of a spin-boson model involving a Debye spectral density, we demonstrate the potential of C-FSSH to deliver highly accurate results for a large region of parameter space. Its uniform description of populations and coherences is found to resolve incorrect behavior observed for conventional FSSH in various cases, in particular at low temperature, while the parameter space regions where it breaks down are shown to be quite limited. Its computational expenses are virtually identical to conventional FSSH.

Correlation matrix renormalization theory for correlated-electron materials with application to the crystalline phases of atomic hydrogen

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Xin; Liu, Jun; Yao, Yong-Xin

Developing accurate and computationally efficient methods to calculate the electronic structure and total energy of correlated-electron materials has been a very challenging task in condensed matter physics and materials science. Recently, we have developed a correlation matrix renormalization (CMR) method which does not assume any empirical Coulomb interaction U parameters and does not have double counting problems in the ground-state total energy calculation. The CMR method has been demonstrated to be accurate in describing both the bonding and bond breaking behaviors of molecules. In this study, we extend the CMR method to the treatment of electron correlations in periodic solidmore » systems. By using a linear hydrogen chain as a benchmark system, we show that the results from the CMR method compare very well with those obtained recently by accurate quantum Monte Carlo (QMC) calculations. We also study the equation of states of three-dimensional crystalline phases of atomic hydrogen. We show that the results from the CMR method agree much better with the available QMC data in comparison with those from density functional theory and Hartree-Fock calculations.« less

Flavor from the electroweak scale

DOE PAGES

Bauer, Martin; Carena, Marcela; Gemmler, Katrin

2015-11-04

We discuss the possibility that flavor hierarchies arise from the electroweak scale in a two Higgs doublet model, in which the two Higgs doublets jointly act as the flavon. Quark masses and mixing angles are explained by effective Yukawa couplings, generated by higher dimensional operators involving quarks and Higgs doublets. Modified Higgs couplings yield important effects on the production cross sections and decay rates of the light Standard Model like Higgs. In addition, flavor changing neutral currents arise at tree-level and lead to strong constraints from meson-antimeson mixing. Remarkably, flavor constraints turn out to prefer a region in parameter spacemore » that is in excellent agreement with the one preferred by recent Higgs precision measurements at the Large Hadron Collider (LHC). Direct searches for extra scalars at the LHC lead to further constraints. Precise predictions for the production and decay modes of the additional Higgs bosons are derived, and we present benchmark scenarios for searches at the LHC Run II. As a result, flavor breaking at the electroweak scale as well as strong coupling effects demand a UV completion at the scale of a few TeV, possibly within the reach of the LHC.« less

CP violation in heavy MSSM Higgs scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carena, M.; Ellis, J.; Lee, J. S.

We introduce and explore new heavy Higgs scenarios in the Minimal Supersymmetric Standard Model (MSSM) with explicit CP violation, which have important phenomenological implications that may be testable at the LHC. For soft supersymmetry-breaking scales M S above a few TeV and a charged Higgs boson mass M H+ above a few hundred GeV, new physics effects including those from explicit CP violation decouple from the light Higgs boson sector. However, such effects can significantly alter the phenomenology of the heavy Higgs bosons while still being consistent with constraints from low-energy observables, for instance electric dipole moments. To consider scenariosmore » with a charged Higgs boson much heavier than the Standard Model (SM) particles but much lighter than the supersymmetric particles, we revisit previous calculations of the MSSM Higgs sector. We compute the Higgs boson masses in the presence of CP violating phases, implementing improved matching and renormalization-group (RG) effects, as well as two-loop RG effects from the effective two-Higgs Doublet Model (2HDM) scale M H± to the scale M S. Here, we illustrate the possibility of non-decoupling CP-violating effects in the heavy Higgs sector using new benchmark scenarios named.« less

The fractured landscape of RNA-seq alignment: the default in our STARs.

PubMed

Ballouz, Sara; Dobin, Alexander; Gingeras, Thomas R; Gillis, Jesse

2018-06-01

Many tools are available for RNA-seq alignment and expression quantification, with comparative value being hard to establish. Benchmarking assessments often highlight methods' good performance, but are focused on either model data or fail to explain variation in performance. This leaves us to ask, what is the most meaningful way to assess different alignment choices? And importantly, where is there room for progress? In this work, we explore the answers to these two questions by performing an exhaustive assessment of the STAR aligner. We assess STAR's performance across a range of alignment parameters using common metrics, and then on biologically focused tasks. We find technical metrics such as fraction mapping or expression profile correlation to be uninformative, capturing properties unlikely to have any role in biological discovery. Surprisingly, we find that changes in alignment parameters within a wide range have little impact on both technical and biological performance. Yet, when performance finally does break, it happens in difficult regions, such as X-Y paralogs and MHC genes. We believe improved reporting by developers will help establish where results are likely to be robust or fragile, providing a better baseline to establish where methodological progress can still occur.

LASL benchmark performance 1978. [CDC STAR-100, 6600, 7600, Cyber 73, and CRAY-1

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKnight, A.L.

1979-08-01

This report presents the results of running several benchmark programs on a CDC STAR-100, a Cray Research CRAY-1, a CDC 6600, a CDC 7600, and a CDC Cyber 73. The benchmark effort included CRAY-1's at several installations running different operating systems and compilers. This benchmark is part of an ongoing program at Los Alamos Scientific Laboratory to collect performance data and monitor the development trend of supercomputers. 3 tables.

Performance Against WELCOA's Worksite Health Promotion Benchmarks Across Years Among Selected US Organizations.

PubMed

Weaver, GracieLee M; Mendenhall, Brandon N; Hunnicutt, David; Picarella, Ryan; Leffelman, Brittanie; Perko, Michael; Bibeau, Daniel L

2018-05-01

The purpose of this study was to quantify the performance of organizations' worksite health promotion (WHP) activities against the benchmarking criteria included in the Well Workplace Checklist (WWC). The Wellness Council of America (WELCOA) developed a tool to assess WHP with its 100-item WWC, which represents WELCOA's 7 performance benchmarks. Workplaces. This study includes a convenience sample of organizations who completed the checklist from 2008 to 2015. The sample size was 4643 entries from US organizations. The WWC includes demographic questions, general questions about WHP programs, and scales to measure the performance against the WELCOA 7 benchmarks. Descriptive analyses of WWC items were completed separately for each year of the study period. The majority of the organizations represented each year were multisite, multishift, medium- to large-sized companies mostly in the services industry. Despite yearly changes in participating organizations, results across the WELCOA 7 benchmark scores were consistent year to year. Across all years, benchmarks that organizations performed the lowest were senior-level support, data collection, and programming; wellness teams and supportive environments were the highest scoring benchmarks. In an era marked with economic swings and health-care reform, it appears that organizations are staying consistent in their performance across these benchmarks. The WWC could be useful for organizations, practitioners, and researchers in assessing the quality of WHP programs.

Key performance indicators to benchmark hospital information systems - a delphi study.

PubMed

Hübner-Bloder, G; Ammenwerth, E

2009-01-01

To identify the key performance indicators for hospital information systems (HIS) that can be used for HIS benchmarking. A Delphi survey with one qualitative and two quantitative rounds. Forty-four HIS experts from health care IT practice and academia participated in all three rounds. Seventy-seven performance indicators were identified and organized into eight categories: technical quality, software quality, architecture and interface quality, IT vendor quality, IT support and IT department quality, workflow support quality, IT outcome quality, and IT costs. The highest ranked indicators are related to clinical workflow support and user satisfaction. Isolated technical indicators or cost indicators were not seen as useful. The experts favored an interdisciplinary group of all the stakeholders, led by hospital management, to conduct the HIS benchmarking. They proposed benchmarking activities both in regular (annual) intervals as well as at defined events (for example after IT introduction). Most of the experts stated that in their institutions no HIS benchmarking activities are being performed at the moment. In the context of IT governance, IT benchmarking is gaining importance in the healthcare area. The found indicators reflect the view of health care IT professionals and researchers. Research is needed to further validate and operationalize key performance indicators, to provide an IT benchmarking framework, and to provide open repositories for a comparison of the HIS benchmarks of different hospitals.

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2014 CFR

2014-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2011 CFR

2011-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2013 CFR

2013-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

Determining the sample size required to establish whether a medical device is non-inferior to an external benchmark.

PubMed

Sayers, Adrian; Crowther, Michael J; Judge, Andrew; Whitehouse, Michael R; Blom, Ashley W

2017-08-28

The use of benchmarks to assess the performance of implants such as those used in arthroplasty surgery is a widespread practice. It provides surgeons, patients and regulatory authorities with the reassurance that implants used are safe and effective. However, it is not currently clear how or how many implants should be statistically compared with a benchmark to assess whether or not that implant is superior, equivalent, non-inferior or inferior to the performance benchmark of interest.We aim to describe the methods and sample size required to conduct a one-sample non-inferiority study of a medical device for the purposes of benchmarking. Simulation study. Simulation study of a national register of medical devices. We simulated data, with and without a non-informative competing risk, to represent an arthroplasty population and describe three methods of analysis (z-test, 1-Kaplan-Meier and competing risks) commonly used in surgical research. We evaluate the performance of each method using power, bias, root-mean-square error, coverage and CI width. 1-Kaplan-Meier provides an unbiased estimate of implant net failure, which can be used to assess if a surgical device is non-inferior to an external benchmark. Small non-inferiority margins require significantly more individuals to be at risk compared with current benchmarking standards. A non-inferiority testing paradigm provides a useful framework for determining if an implant meets the required performance defined by an external benchmark. Current contemporary benchmarking standards have limited power to detect non-inferiority, and substantially larger samples sizes, in excess of 3200 procedures, are required to achieve a power greater than 60%. It is clear when benchmarking implant performance, net failure estimated using 1-KM is preferential to crude failure estimated by competing risk models. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

International benchmarking of specialty hospitals. A series of case studies on comprehensive cancer centres.

PubMed

van Lent, Wineke A M; de Beer, Relinde D; van Harten, Wim H

2010-08-31

Benchmarking is one of the methods used in business that is applied to hospitals to improve the management of their operations. International comparison between hospitals can explain performance differences. As there is a trend towards specialization of hospitals, this study examines the benchmarking process and the success factors of benchmarking in international specialized cancer centres. Three independent international benchmarking studies on operations management in cancer centres were conducted. The first study included three comprehensive cancer centres (CCC), three chemotherapy day units (CDU) were involved in the second study and four radiotherapy departments were included in the final study. Per multiple case study a research protocol was used to structure the benchmarking process. After reviewing the multiple case studies, the resulting description was used to study the research objectives. We adapted and evaluated existing benchmarking processes through formalizing stakeholder involvement and verifying the comparability of the partners. We also devised a framework to structure the indicators to produce a coherent indicator set and better improvement suggestions. Evaluating the feasibility of benchmarking as a tool to improve hospital processes led to mixed results. Case study 1 resulted in general recommendations for the organizations involved. In case study 2, the combination of benchmarking and lean management led in one CDU to a 24% increase in bed utilization and a 12% increase in productivity. Three radiotherapy departments of case study 3, were considering implementing the recommendations.Additionally, success factors, such as a well-defined and small project scope, partner selection based on clear criteria, stakeholder involvement, simple and well-structured indicators, analysis of both the process and its results and, adapt the identified better working methods to the own setting, were found. The improved benchmarking process and the success factors can produce relevant input to improve the operations management of specialty hospitals.

International benchmarking of specialty hospitals. A series of case studies on comprehensive cancer centres

PubMed Central

2010-01-01

Background Benchmarking is one of the methods used in business that is applied to hospitals to improve the management of their operations. International comparison between hospitals can explain performance differences. As there is a trend towards specialization of hospitals, this study examines the benchmarking process and the success factors of benchmarking in international specialized cancer centres. Methods Three independent international benchmarking studies on operations management in cancer centres were conducted. The first study included three comprehensive cancer centres (CCC), three chemotherapy day units (CDU) were involved in the second study and four radiotherapy departments were included in the final study. Per multiple case study a research protocol was used to structure the benchmarking process. After reviewing the multiple case studies, the resulting description was used to study the research objectives. Results We adapted and evaluated existing benchmarking processes through formalizing stakeholder involvement and verifying the comparability of the partners. We also devised a framework to structure the indicators to produce a coherent indicator set and better improvement suggestions. Evaluating the feasibility of benchmarking as a tool to improve hospital processes led to mixed results. Case study 1 resulted in general recommendations for the organizations involved. In case study 2, the combination of benchmarking and lean management led in one CDU to a 24% increase in bed utilization and a 12% increase in productivity. Three radiotherapy departments of case study 3, were considering implementing the recommendations. Additionally, success factors, such as a well-defined and small project scope, partner selection based on clear criteria, stakeholder involvement, simple and well-structured indicators, analysis of both the process and its results and, adapt the identified better working methods to the own setting, were found. Conclusions The improved benchmarking process and the success factors can produce relevant input to improve the operations management of specialty hospitals. PMID:20807408

Benchmarking initiatives in the water industry.

PubMed

Parena, R; Smeets, E

2001-01-01

Customer satisfaction and service care are every day pushing professionals in the water industry to seek to improve their performance, lowering costs and increasing the provided service level. Process Benchmarking is generally recognised as a systematic mechanism of comparing one's own utility with other utilities or businesses with the intent of self-improvement by adopting structures or methods used elsewhere. The IWA Task Force on Benchmarking, operating inside the Statistics and Economics Committee, has been committed to developing a general accepted concept of Process Benchmarking to support water decision-makers in addressing issues of efficiency. In a first step the Task Force disseminated among the Committee members a questionnaire focused on providing suggestions about the kind, the evolution degree and the main concepts of Benchmarking adopted in the represented Countries. A comparison among the guidelines adopted in The Netherlands and Scandinavia has recently challenged the Task Force in drafting a methodology for a worldwide process benchmarking in water industry. The paper provides a framework of the most interesting benchmarking experiences in the water sector and describes in detail both the final results of the survey and the methodology focused on identification of possible improvement areas.

A review on the benchmarking concept in Malaysian construction safety performance

NASA Astrophysics Data System (ADS)

Ishak, Nurfadzillah; Azizan, Muhammad Azizi

2018-02-01

Construction industry is one of the major industries that propels Malaysia's economy in highly contributes to our nation's GDP growth, yet the high fatality rates on construction sites have caused concern among safety practitioners and the stakeholders. Hence, there is a need of benchmarking in performance of Malaysia's construction industry especially in terms of safety. This concept can create a fertile ground for ideas, but only in a receptive environment, organization that share good practices and compare their safety performance against other benefit most to establish improvement in safety culture. This research was conducted to study the awareness important, evaluate current practice and improvement, and also identify the constraint in implement of benchmarking on safety performance in our industry. Additionally, interviews with construction professionals were come out with different views on this concept. Comparison has been done to show the different understanding of benchmarking approach and how safety performance can be benchmarked. But, it's viewed as one mission, which to evaluate objectives identified through benchmarking that will improve the organization's safety performance. Finally, the expected result from this research is to help Malaysia's construction industry implement best practice in safety performance management through the concept of benchmarking.

Machine characterization and benchmark performance prediction

NASA Technical Reports Server (NTRS)

Saavedra-Barrera, Rafael H.

1988-01-01

From runs of standard benchmarks or benchmark suites, it is not possible to characterize the machine nor to predict the run time of other benchmarks which have not been run. A new approach to benchmarking and machine characterization is reported. The creation and use of a machine analyzer is described, which measures the performance of a given machine on FORTRAN source language constructs. The machine analyzer yields a set of parameters which characterize the machine and spotlight its strong and weak points. Also described is a program analyzer, which analyzes FORTRAN programs and determines the frequency of execution of each of the same set of source language operations. It is then shown that by combining a machine characterization and a program characterization, we are able to predict with good accuracy the run time of a given benchmark on a given machine. Characterizations are provided for the Cray-X-MP/48, Cyber 205, IBM 3090/200, Amdahl 5840, Convex C-1, VAX 8600, VAX 11/785, VAX 11/780, SUN 3/50, and IBM RT-PC/125, and for the following benchmark programs or suites: Los Alamos (BMK8A1), Baskett, Linpack, Livermore Loops, Madelbrot Set, NAS Kernels, Shell Sort, Smith, Whetstone and Sieve of Erathostenes.

7 CFR 1469.7 - Benchmark condition inventory and conservation stewardship plan.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Benchmark condition inventory and conservation...) COMMODITY CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS CONSERVATION SECURITY PROGRAM General Provisions § 1469.7 Benchmark condition inventory and conservation stewardship...

Benchmarking, Total Quality Management, and Libraries.

ERIC Educational Resources Information Center

Shaughnessy, Thomas W.

1993-01-01

Discussion of the use of Total Quality Management (TQM) in higher education and academic libraries focuses on the identification, collection, and use of reliable data. Methods for measuring quality, including benchmarking, are described; performance measures are considered; and benchmarking techniques are examined. (11 references) (MES)

77 FR 36533 - Notice of Availability of the Benchmark Dose Technical Guidance

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-19

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9688-7] Notice of Availability of the Benchmark Dose Technical Guidance AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of Availability. SUMMARY: The U.S. Environmental Protection Agency is announcing the availability of Benchmark Dose Technical...

EPA and EFSA approaches for Benchmark Dose modeling

EPA Science Inventory

Benchmark dose (BMD) modeling has become the preferred approach in the analysis of toxicological dose-response data for the purpose of deriving human health toxicity values. The software packages most often used are Benchmark Dose Software (BMDS, developed by EPA) and PROAST (de...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate... planning services and supplies and other appropriate preventive services, as designated by the Secretary... State for purposes of comparison in establishing the aggregate actuarial value of the benchmark...

BENCHMARK DOSE TECHNICAL GUIDANCE DOCUMENT ...

EPA Pesticide Factsheets

The purpose of this document is to provide guidance for the Agency on the application of the benchmark dose approach in determining the point of departure (POD) for health effects data, whether a linear or nonlinear low dose extrapolation is used. The guidance includes discussion on computation of benchmark doses and benchmark concentrations (BMDs and BMCs) and their lower confidence limits, data requirements, dose-response analysis, and reporting requirements. This guidance is based on today's knowledge and understanding, and on experience gained in using this approach.

FY 2004 Top 200 Users Survey Report

DTIC Science & Technology

2004-10-01

Rating 82% 79% 80% ACSI Federal Government Benchmark* 71.1% 70.2% 70.9% DTIC Excels by +10.9 +8.8 +9.1 *ACSI is the official service quality benchmark...ACSI Federal Government Benchmark* 71.1% 70.2% 70.9% DTIC Excels by +10.9 +8.8 +9.1 *ACSI is the official service quality benchmark for the Federal...Users Survey % DTIC’s Other Overall Product/ Service Quality and Performance: Not only were we able to ascertain product and service usage data from

Issues in Benchmark Metric Selection

NASA Astrophysics Data System (ADS)

Crolotte, Alain

It is true that a metric can influence a benchmark but will esoteric metrics create more problems than they will solve? We answer this question affirmatively by examining the case of the TPC-D metric which used the much debated geometric mean for the single-stream test. We will show how a simple choice influenced the benchmark and its conduct and, to some extent, DBMS development. After examining other alternatives our conclusion is that the “real” measure for a decision-support benchmark is the arithmetic mean.

Benchmarking for Excellence and the Nursing Process

NASA Technical Reports Server (NTRS)

Sleboda, Claire

1999-01-01

Nursing is a service profession. The services provided are essential to life and welfare. Therefore, setting the benchmark for high quality care is fundamental. Exploring the definition of a benchmark value will help to determine a best practice approach. A benchmark is the descriptive statement of a desired level of performance against which quality can be judged. It must be sufficiently well understood by managers and personnel in order that it may serve as a standard against which to measure value.

Give me a better break: Choosing workday break activities to maximize resource recovery.

PubMed

Hunter, Emily M; Wu, Cindy

2016-02-01

Surprisingly little research investigates employee breaks at work, and even less research provides prescriptive suggestions for better workday breaks in terms of when, where, and how break activities are most beneficial. Based on the effort-recovery model and using experience sampling methodology, we examined the characteristics of employee workday breaks with 95 employees across 5 workdays. In addition, we examined resources as a mediator between break characteristics and well-being. Multilevel analysis results indicated that activities that were preferred and earlier in the work shift related to more resource recovery following the break. We also found that resources mediated the influence of preferred break activities and time of break on health symptoms and that resource recovery benefited person-level outcomes of emotional exhaustion, job satisfaction, and organizational citizenship behavior. Finally, break length interacted with the number of breaks per day such that longer breaks and frequent short breaks were associated with more resources than infrequent short breaks. (c) 2016 APA, all rights reserved).

Proposed biopsy performance benchmarks for MRI based on an audit of a large academic center.

PubMed

Sedora Román, Neda I; Mehta, Tejas S; Sharpe, Richard E; Slanetz, Priscilla J; Venkataraman, Shambhavi; Fein-Zachary, Valerie; Dialani, Vandana

2018-05-01

Performance benchmarks exist for mammography (MG); however, performance benchmarks for magnetic resonance imaging (MRI) are not yet fully developed. The purpose of our study was to perform an MRI audit based on established MG and screening MRI benchmarks and to review whether these benchmarks can be applied to an MRI practice. An IRB approved retrospective review of breast MRIs was performed at our center from 1/1/2011 through 12/31/13. For patients with biopsy recommendation, core biopsy and surgical pathology results were reviewed. The data were used to derive mean performance parameter values, including abnormal interpretation rate (AIR), positive predictive value (PPV), cancer detection rate (CDR), percentage of minimal cancers and axillary node negative cancers and compared with MG and screening MRI benchmarks. MRIs were also divided by screening and diagnostic indications to assess for differences in performance benchmarks amongst these two groups. Of the 2455 MRIs performed over 3-years, 1563 were performed for screening indications and 892 for diagnostic indications. With the exception of PPV2 for screening breast MRIs from 2011 to 2013, PPVs were met for our screening and diagnostic populations when compared to the MRI screening benchmarks established by the Breast Imaging Reporting and Data System (BI-RADS) 5 Atlas ® . AIR and CDR were lower for screening indications as compared to diagnostic indications. New MRI screening benchmarks can be used for screening MRI audits while the American College of Radiology (ACR) desirable goals for diagnostic MG can be used for diagnostic MRI audits. Our study corroborates established findings regarding differences in AIR and CDR amongst screening versus diagnostic indications. © 2017 Wiley Periodicals, Inc.

The impact of a scheduling change on ninth grade high school performance on biology benchmark exams and the California Standards Test

NASA Astrophysics Data System (ADS)

Leonardi, Marcelo

The primary purpose of this study was to examine the impact of a scheduling change from a trimester 4x4 block schedule to a modified hybrid schedule on student achievement in ninth grade biology courses. This study examined the impact of the scheduling change on student achievement through teacher created benchmark assessments in Genetics, DNA, and Evolution and on the California Standardized Test in Biology. The secondary purpose of this study examined the ninth grade biology teacher perceptions of ninth grade biology student achievement. Using a mixed methods research approach, data was collected both quantitatively and qualitatively as aligned to research questions. Quantitative methods included gathering data from departmental benchmark exams and California Standardized Test in Biology and conducting multiple analysis of covariance and analysis of covariance to determine significance differences. Qualitative methods include journal entries questions and focus group interviews. The results revealed a statistically significant increase in scores on both the DNA and Evolution benchmark exams. DNA and Evolution benchmark exams showed significant improvements from a change in scheduling format. The scheduling change was responsible for 1.5% of the increase in DNA benchmark scores and 2% of the increase in Evolution benchmark scores. The results revealed a statistically significant decrease in scores on the Genetics Benchmark exam as a result of the scheduling change. The scheduling change was responsible for 1% of the decrease in Genetics benchmark scores. The results also revealed a statistically significant increase in scores on the CST Biology exam. The scheduling change was responsible for .7% of the increase in CST Biology scores. Results of the focus group discussions indicated that all teachers preferred the modified hybrid schedule over the trimester schedule and that it improved student achievement.

The MCNP6 Analytic Criticality Benchmark Suite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Forrest B.

2016-06-16

Analytical benchmarks provide an invaluable tool for verifying computer codes used to simulate neutron transport. Several collections of analytical benchmark problems [1-4] are used routinely in the verification of production Monte Carlo codes such as MCNP® [5,6]. Verification of a computer code is a necessary prerequisite to the more complex validation process. The verification process confirms that a code performs its intended functions correctly. The validation process involves determining the absolute accuracy of code results vs. nature. In typical validations, results are computed for a set of benchmark experiments using a particular methodology (code, cross-section data with uncertainties, and modeling)more » and compared to the measured results from the set of benchmark experiments. The validation process determines bias, bias uncertainty, and possibly additional margins. Verification is generally performed by the code developers, while validation is generally performed by code users for a particular application space. The VERIFICATION_KEFF suite of criticality problems [1,2] was originally a set of 75 criticality problems found in the literature for which exact analytical solutions are available. Even though the spatial and energy detail is necessarily limited in analytical benchmarks, typically to a few regions or energy groups, the exact solutions obtained can be used to verify that the basic algorithms, mathematics, and methods used in complex production codes perform correctly. The present work has focused on revisiting this benchmark suite. A thorough review of the problems resulted in discarding some of them as not suitable for MCNP benchmarking. For the remaining problems, many of them were reformulated to permit execution in either multigroup mode or in the normal continuous-energy mode for MCNP. Execution of the benchmarks in continuous-energy mode provides a significant advance to MCNP verification methods.« less

Length of stay benchmarks for inpatient rehabilitation after stroke.

PubMed

Meyer, Matthew; Britt, Eileen; McHale, Heather A; Teasell, Robert

2012-01-01

In Canada, no standardized benchmarks for length of stay (LOS) have been established for post-stroke inpatient rehabilitation. This paper describes the development of a severity specific median length of stay benchmarking strategy, assessment of its impact after one year of implementation in a Canadian rehabilitation hospital, and establishment of updated benchmarks that may be useful for comparison with other facilities across Canada. Patient data were retrospectively assessed for all patients admitted to a single post-acute stroke rehabilitation unit in Ontario, Canada between April 2005 and March 2008. Rehabilitation Patient Groups (RPGs) were used to establish stratified median length of stay benchmarks for each group that were incorporated into team rounds beginning in October 2009. Benchmark impact was assessed using mean LOS, FIM(®) gain, and discharge destination for each RPG group, collected prospectively for one year, compared against similar information from the previous calendar year. Benchmarks were then adjusted accordingly for future use. Between October 2009 and September 2010, a significant reduction in average LOS was noted compared to the previous year (35.3 vs. 41.2 days; p < 0.05). Reductions in LOS were noted in each RPG group including statistically significant reductions in 4 of the 7 groups. As intended, reductions in LOS were achieved with no significant reduction in mean FIM(®) gain or proportion of patients discharged home compared to the previous year. Adjusted benchmarks for LOS ranged from 13 to 48 days depending on the RPG group. After a single year of implementation, severity specific benchmarks helped the rehabilitation team reduce LOS while maintaining the same levels of functional gain and achieving the same rate of discharge to the community. © 2012 Informa UK, Ltd.

Benchmark duration of work hours for development of fatigue symptoms in Japanese workers with adjustment for job-related stress.

PubMed

Suwazono, Yasushi; Dochi, Mirei; Kobayashi, Etsuko; Oishi, Mitsuhiro; Okubo, Yasushi; Tanaka, Kumihiko; Sakata, Kouichi

2008-12-01

The objective of this study was to calculate benchmark durations and lower 95% confidence limits for benchmark durations of working hours associated with subjective fatigue symptoms by applying the benchmark dose approach while adjusting for job-related stress using multiple logistic regression analyses. A self-administered questionnaire was completed by 3,069 male and 412 female daytime workers (age 18-67 years) in a Japanese steel company. The eight dependent variables in the Cumulative Fatigue Symptoms Index were decreased vitality, general fatigue, physical disorders, irritability, decreased willingness to work, anxiety, depressive feelings, and chronic tiredness. Independent variables were daily working hours, four subscales (job demand, job control, interpersonal relationship, and job suitability) of the Brief Job Stress Questionnaire, and other potential covariates. Using significant parameters for working hours and those for other covariates, the benchmark durations of working hours were calculated for the corresponding Index property. Benchmark response was set at 5% or 10%. Assuming a condition of worst job stress, the benchmark duration/lower 95% confidence limit for benchmark duration of working hours per day with a benchmark response of 5% or 10% were 10.0/9.4 or 11.7/10.7 (irritability) and 9.2/8.9 or 10.4/9.8 (chronic tiredness) in men and 8.9/8.4 or 9.8/8.9 (chronic tiredness) in women. The threshold amounts of working hours for fatigue symptoms under the worst job-related stress were very close to the standard daily working hours in Japan. The results strongly suggest that special attention should be paid to employees whose working hours exceed threshold amounts based on individual levels of job-related stress.

Developing a Benchmarking Process in Perfusion: A Report of the Perfusion Downunder Collaboration

PubMed Central

Baker, Robert A.; Newland, Richard F.; Fenton, Carmel; McDonald, Michael; Willcox, Timothy W.; Merry, Alan F.

2012-01-01

Abstract: Improving and understanding clinical practice is an appropriate goal for the perfusion community. The Perfusion Downunder Collaboration has established a multi-center perfusion focused database aimed at achieving these goals through the development of quantitative quality indicators for clinical improvement through benchmarking. Data were collected using the Perfusion Downunder Collaboration database from procedures performed in eight Australian and New Zealand cardiac centers between March 2007 and February 2011. At the Perfusion Downunder Meeting in 2010, it was agreed by consensus, to report quality indicators (QI) for glucose level, arterial outlet temperature, and pCO2 management during cardiopulmonary bypass. The values chosen for each QI were: blood glucose ≥4 mmol/L and ≤10 mmol/L; arterial outlet temperature ≤37°C; and arterial blood gas pCO2 ≥ 35 and ≤45 mmHg. The QI data were used to derive benchmarks using the Achievable Benchmark of Care (ABC™) methodology to identify the incidence of QIs at the best performing centers. Five thousand four hundred and sixty-five procedures were evaluated to derive QI and benchmark data. The incidence of the blood glucose QI ranged from 37–96% of procedures, with a benchmark value of 90%. The arterial outlet temperature QI occurred in 16–98% of procedures with the benchmark of 94%; while the arterial pCO2 QI occurred in 21–91%, with the benchmark value of 80%. We have derived QIs and benchmark calculations for the management of several key aspects of cardiopulmonary bypass to provide a platform for improving the quality of perfusion practice. PMID:22730861

Developing and Trialling an independent, scalable and repeatable IT-benchmarking procedure for healthcare organisations.

PubMed

Liebe, J D; Hübner, U

2013-01-01

Continuous improvements of IT-performance in healthcare organisations require actionable performance indicators, regularly conducted, independent measurements and meaningful and scalable reference groups. Existing IT-benchmarking initiatives have focussed on the development of reliable and valid indicators, but less on the questions about how to implement an environment for conducting easily repeatable and scalable IT-benchmarks. This study aims at developing and trialling a procedure that meets the afore-mentioned requirements. We chose a well established, regularly conducted (inter-) national IT-survey of healthcare organisations (IT-Report Healthcare) as the environment and offered the participants of the 2011 survey (CIOs of hospitals) to enter a benchmark. The 61 structural and functional performance indicators covered among others the implementation status and integration of IT-systems and functions, global user satisfaction and the resources of the IT-department. Healthcare organisations were grouped by size and ownership. The benchmark results were made available electronically and feedback on the use of these results was requested after several months. Fifty-ninehospitals participated in the benchmarking. Reference groups consisted of up to 141 members depending on the number of beds (size) and the ownership (public vs. private). A total of 122 charts showing single indicator frequency views were sent to each participant. The evaluation showed that 94.1% of the CIOs who participated in the evaluation considered this benchmarking beneficial and reported that they would enter again. Based on the feedback of the participants we developed two additional views that provide a more consolidated picture. The results demonstrate that establishing an independent, easily repeatable and scalable IT-benchmarking procedure is possible and was deemed desirable. Based on these encouraging results a new benchmarking round which includes process indicators is currently conducted.

NAS Grid Benchmarks: A Tool for Grid Space Exploration

NASA Technical Reports Server (NTRS)

Frumkin, Michael; VanderWijngaart, Rob F.; Biegel, Bryan (Technical Monitor)

2001-01-01

We present an approach for benchmarking services provided by computational Grids. It is based on the NAS Parallel Benchmarks (NPB) and is called NAS Grid Benchmark (NGB) in this paper. We present NGB as a data flow graph encapsulating an instance of an NPB code in each graph node, which communicates with other nodes by sending/receiving initialization data. These nodes may be mapped to the same or different Grid machines. Like NPB, NGB will specify several different classes (problem sizes). NGB also specifies the generic Grid services sufficient for running the bench-mark. The implementor has the freedom to choose any specific Grid environment. However, we describe a reference implementation in Java, and present some scenarios for using NGB.

Seismo-acoustic ray model benchmarking against experimental tank data.

PubMed

Camargo Rodríguez, Orlando; Collis, Jon M; Simpson, Harry J; Ey, Emanuel; Schneiderwind, Joseph; Felisberto, Paulo

2012-08-01

Acoustic predictions of the recently developed traceo ray model, which accounts for bottom shear properties, are benchmarked against tank experimental data from the EPEE-1 and EPEE-2 (Elastic Parabolic Equation Experiment) experiments. Both experiments are representative of signal propagation in a Pekeris-like shallow-water waveguide over a non-flat isotropic elastic bottom, where significant interaction of the signal with the bottom can be expected. The benchmarks show, in particular, that the ray model can be as accurate as a parabolic approximation model benchmarked in similar conditions. The results of benchmarking are important, on one side, as a preliminary experimental validation of the model and, on the other side, demonstrates the reliability of the ray approach for seismo-acoustic applications.

Modification and benchmarking of MCNP for low-energy tungsten spectra.

PubMed

Mercier, J R; Kopp, D T; McDavid, W D; Dove, S B; Lancaster, J L; Tucker, D M

2000-12-01

The MCNP Monte Carlo radiation transport code was modified for diagnostic medical physics applications. In particular, the modified code was thoroughly benchmarked for the production of polychromatic tungsten x-ray spectra in the 30-150 kV range. Validating the modified code for coupled electron-photon transport with benchmark spectra was supplemented with independent electron-only and photon-only transport benchmarks. Major revisions to the code included the proper treatment of characteristic K x-ray production and scoring, new impact ionization cross sections, and new bremsstrahlung cross sections. Minor revisions included updated photon cross sections, electron-electron bremsstrahlung production, and K x-ray yield. The modified MCNP code is benchmarked to electron backscatter factors, x-ray spectra production, and primary and scatter photon transport.

NAS Grid Benchmarks. 1.0

NASA Technical Reports Server (NTRS)

VanderWijngaart, Rob; Frumkin, Michael; Biegel, Bryan A. (Technical Monitor)

2002-01-01

We provide a paper-and-pencil specification of a benchmark suite for computational grids. It is based on the NAS (NASA Advanced Supercomputing) Parallel Benchmarks (NPB) and is called the NAS Grid Benchmarks (NGB). NGB problems are presented as data flow graphs encapsulating an instance of a slightly modified NPB task in each graph node, which communicates with other nodes by sending/receiving initialization data. Like NPB, NGB specifies several different classes (problem sizes). In this report we describe classes S, W, and A, and provide verification values for each. The implementor has the freedom to choose any language, grid environment, security model, fault tolerance/error correction mechanism, etc., as long as the resulting implementation passes the verification test and reports the turnaround time of the benchmark.

A Competitive Benchmarking Study of Noncredit Program Administration.

ERIC Educational Resources Information Center

Alstete, Jeffrey W.

1996-01-01

A benchmarking project to measure administrative processes and financial ratios received 57 usable replies from 300 noncredit continuing education programs. Programs with strong financial surpluses were identified and their processes benchmarked (including response to inquiries, registrants, registrant/staff ratio, new courses, class size,…

Benchmarking Helps Measure Union Programs, Operations.

ERIC Educational Resources Information Center

Mann, Jerry

2001-01-01

Explores three examples of benchmarking by college student unions. Focuses on how a union can collect information from other unions for use as benchmarking standards for the purposes of selling a concept or justifying program increases, or for comparing a union's financial performance to other unions. (EV)

Engineering department physical plant staffing requirements.

PubMed

Cole, C

1997-05-01

There is a considerable effort in the health care arena to establish credible engineering manpower yardsticks that are universally applicable as a benchmark. This document was created by using one facility's own benchmark criteria that can be used to help develop either internal or competitive benchmarking comparisons.

The Learning Organisation: Results of a Benchmarking Study.

ERIC Educational Resources Information Center

Zairi, Mohamed

1999-01-01

Learning in corporations was assessed using these benchmarks: core qualities of creative organizations, characteristic of organizational creativity, attributes of flexible organizations, use of diversity and conflict, creative human resource management systems, and effective and successful teams. These benchmarks are key elements of the learning…

75 FR 75628 - Final Guidance for Federal Departments and Agencies on Establishing, Applying, and Revising...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-06

... and facilitate the use of documentation in future evaluations and benchmarking. Extraordinary.... Benchmarking Other Agencies' Experiences A Federal agency cannot rely on another agency's categorical exclusion... was established. Federal agencies can also substantiate categorical exclusions by benchmarking, or...

Nomenclatural Benchmarking: The roles of digital typification and telemicroscopy

USDA-ARS?s Scientific Manuscript database

The process of nomenclatural benchmarking is the examination of type specimens of all available names to ascertain which currently accepted species the specimen bearing the name falls within. We propose a strategy for addressing four challenges for nomenclatural benchmarking. First, there is the mat...

INTEGRAL BENCHMARK DATA FOR NUCLEAR DATA TESTING THROUGH THE ICSBEP AND THE NEWLY ORGANIZED IRPHEP

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. Blair Briggs; Lori Scott; Yolanda Rugama

The status of the International Criticality Safety Benchmark Evaluation Project (ICSBEP) was last reported in a nuclear data conference at the International Conference on Nuclear Data for Science and Technology, ND-2004, in Santa Fe, New Mexico. Since that time the number and type of integral benchmarks have increased significantly. Included in the ICSBEP Handbook are criticality-alarm / shielding and fundamental physic benchmarks in addition to the traditional critical / subcritical benchmark data. Since ND 2004, a reactor physics counterpart to the ICSBEP, the International Reactor Physics Experiment Evaluation Project (IRPhEP) was initiated. The IRPhEP is patterned after the ICSBEP, butmore » focuses on other integral measurements, such as buckling, spectral characteristics, reactivity effects, reactivity coefficients, kinetics measurements, reaction-rate and power distributions, nuclide compositions, and other miscellaneous-type measurements in addition to the critical configuration. The status of these two projects is discussed and selected benchmarks highlighted in this paper.« less

Statistical Analysis of NAS Parallel Benchmarks and LINPACK Results

NASA Technical Reports Server (NTRS)

Meuer, Hans-Werner; Simon, Horst D.; Strohmeier, Erich; Lasinski, T. A. (Technical Monitor)

1994-01-01

In the last three years extensive performance data have been reported for parallel machines both based on the NAS Parallel Benchmarks, and on LINPACK. In this study we have used the reported benchmark results and performed a number of statistical experiments using factor, cluster, and regression analyses. In addition to the performance results of LINPACK and the eight NAS parallel benchmarks, we have also included peak performance of the machine, and the LINPACK n and n(sub 1/2) values. Some of the results and observations can be summarized as follows: 1) All benchmarks are strongly correlated with peak performance. 2) LINPACK and EP have each a unique signature. 3) The remaining NPB can grouped into three groups as follows: (CG and IS), (LU and SP), and (MG, FT, and BT). Hence three (or four with EP) benchmarks are sufficient to characterize the overall NPB performance. Our poster presentation will follow a standard poster format, and will present the data of our statistical analysis in detail.

Performance analysis of fusion nuclear-data benchmark experiments for light to heavy materials in MeV energy region with a neutron spectrum shifter

NASA Astrophysics Data System (ADS)

Murata, Isao; Ohta, Masayuki; Miyamaru, Hiroyuki; Kondo, Keitaro; Yoshida, Shigeo; Iida, Toshiyuki; Ochiai, Kentaro; Konno, Chikara

2011-10-01

Nuclear data are indispensable for development of fusion reactor candidate materials. However, benchmarking of the nuclear data in MeV energy region is not yet adequate. In the present study, benchmark performance in the MeV energy region was investigated theoretically for experiments by using a 14 MeV neutron source. We carried out a systematical analysis for light to heavy materials. As a result, the benchmark performance for the neutron spectrum was confirmed to be acceptable, while for gamma-rays it was not sufficiently accurate. Consequently, a spectrum shifter has to be applied. Beryllium had the best performance as a shifter. Moreover, a preliminary examination of whether it is really acceptable that only the spectrum before the last collision is considered in the benchmark performance analysis. It was pointed out that not only the last collision but also earlier collisions should be considered equally in the benchmark performance analysis.

Performance Characteristics of the Multi-Zone NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Jin, Haoqiang; VanderWijngaart, Rob F.

2003-01-01

We describe a new suite of computational benchmarks that models applications featuring multiple levels of parallelism. Such parallelism is often available in realistic flow computations on systems of grids, but had not previously been captured in bench-marks. The new suite, named NPB Multi-Zone, is extended from the NAS Parallel Benchmarks suite, and involves solving the application benchmarks LU, BT and SP on collections of loosely coupled discretization meshes. The solutions on the meshes are updated independently, but after each time step they exchange boundary value information. This strategy provides relatively easily exploitable coarse-grain parallelism between meshes. Three reference implementations are available: one serial, one hybrid using the Message Passing Interface (MPI) and OpenMP, and another hybrid using a shared memory multi-level programming model (SMP+OpenMP). We examine the effectiveness of hybrid parallelization paradigms in these implementations on three different parallel computers. We also use an empirical formula to investigate the performance characteristics of the multi-zone benchmarks.

An integrated data envelopment analysis-artificial neural network approach for benchmarking of bank branches

NASA Astrophysics Data System (ADS)

Shokrollahpour, Elsa; Hosseinzadeh Lotfi, Farhad; Zandieh, Mostafa

2016-06-01

Efficiency and quality of services are crucial to today's banking industries. The competition in this section has become increasingly intense, as a result of fast improvements in Technology. Therefore, performance analysis of the banking sectors attracts more attention these days. Even though data envelopment analysis (DEA) is a pioneer approach in the literature as of an efficiency measurement tool and finding benchmarks, it is on the other hand unable to demonstrate the possible future benchmarks. The drawback to it could be that the benchmarks it provides us with, may still be less efficient compared to the more advanced future benchmarks. To cover for this weakness, artificial neural network is integrated with DEA in this paper to calculate the relative efficiency and more reliable benchmarks of one of the Iranian commercial bank branches. Therefore, each branch could have a strategy to improve the efficiency and eliminate the cause of inefficiencies based on a 5-year time forecast.

Development of Benchmark Examples for Quasi-Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2012-01-01

The development of benchmark examples for quasi-static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for Abaqus/Standard. The example is based on a finite element model of a Double-Cantilever Beam specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, a quasi-static benchmark example was created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

Development of Benchmark Examples for Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Kruger, Ronald

2011-01-01

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

Benchmarking Multilayer-HySEA model for landslide generated tsunami. HTHMP validation process.

NASA Astrophysics Data System (ADS)

Macias, J.; Escalante, C.; Castro, M. J.

2017-12-01

Landslide tsunami hazard may be dominant along significant parts of the coastline around the world, in particular in the USA, as compared to hazards from other tsunamigenic sources. This fact motivated NTHMP about the need of benchmarking models for landslide generated tsunamis, following the same methodology already used for standard tsunami models when the source is seismic. To perform the above-mentioned validation process, a set of candidate benchmarks were proposed. These benchmarks are based on a subset of available laboratory data sets for solid slide experiments and deformable slide experiments, and include both submarine and subaerial slides. A benchmark based on a historic field event (Valdez, AK, 1964) close the list of proposed benchmarks. A total of 7 benchmarks. The Multilayer-HySEA model including non-hydrostatic effects has been used to perform all the benchmarking problems dealing with laboratory experiments proposed in the workshop that was organized at Texas A&M University - Galveston, on January 9-11, 2017 by NTHMP. The aim of this presentation is to show some of the latest numerical results obtained with the Multilayer-HySEA (non-hydrostatic) model in the framework of this validation effort.Acknowledgements. This research has been partially supported by the Spanish Government Research project SIMURISK (MTM2015-70490-C02-01-R) and University of Malaga, Campus de Excelencia Internacional Andalucía Tech. The GPU computations were performed at the Unit of Numerical Methods (University of Malaga).

Development and Application of Benchmark Examples for Mode II Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2011-01-01

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

ICSBEP Benchmarks For Nuclear Data Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Briggs, J. Blair

2005-05-24

The International Criticality Safety Benchmark Evaluation Project (ICSBEP) was initiated in 1992 by the United States Department of Energy. The ICSBEP became an official activity of the Organization for Economic Cooperation and Development (OECD) -- Nuclear Energy Agency (NEA) in 1995. Representatives from the United States, United Kingdom, France, Japan, the Russian Federation, Hungary, Republic of Korea, Slovenia, Serbia and Montenegro (formerly Yugoslavia), Kazakhstan, Spain, Israel, Brazil, Poland, and the Czech Republic are now participating. South Africa, India, China, and Germany are considering participation. The purpose of the ICSBEP is to identify, evaluate, verify, and formally document a comprehensive andmore » internationally peer-reviewed set of criticality safety benchmark data. The work of the ICSBEP is published as an OECD handbook entitled ''International Handbook of Evaluated Criticality Safety Benchmark Experiments.'' The 2004 Edition of the Handbook contains benchmark specifications for 3331 critical or subcritical configurations that are intended for use in validation efforts and for testing basic nuclear data. New to the 2004 Edition of the Handbook is a draft criticality alarm / shielding type benchmark that should be finalized in 2005 along with two other similar benchmarks. The Handbook is being used extensively for nuclear data testing and is expected to be a valuable resource for code and data validation and improvement efforts for decades to come. Specific benchmarks that are useful for testing structural materials such as iron, chromium, nickel, and manganese; beryllium; lead; thorium; and 238U are highlighted.« less

In Search of a Time Efficient Approach to Crack and Delamination Growth Predictions in Composites

NASA Technical Reports Server (NTRS)

Krueger, Ronald; Carvalho, Nelson

2016-01-01

Analysis benchmarking was used to assess the accuracy and time efficiency of algorithms suitable for automated delamination growth analysis. First, the Floating Node Method (FNM) was introduced and its combination with a simple exponential growth law (Paris Law) and Virtual Crack Closure technique (VCCT) was discussed. Implementation of the method into a user element (UEL) in Abaqus/Standard(Registered TradeMark) was also presented. For the assessment of growth prediction capabilities, an existing benchmark case based on the Double Cantilever Beam (DCB) specimen was briefly summarized. Additionally, the development of new benchmark cases based on the Mixed-Mode Bending (MMB) specimen to assess the growth prediction capabilities under mixed-mode I/II conditions was discussed in detail. A comparison was presented, in which the benchmark cases were used to assess the existing low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) in comparison to the FNM-VCCT fatigue growth analysis implementation. The low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) was able to yield results that were in good agreement with the DCB benchmark example. Results for the MMB benchmark cases, however, only captured the trend correctly. The user element (FNM-VCCT) always yielded results that were in excellent agreement with all benchmark cases, at a fraction of the analysis time. The ability to assess the implementation of two methods in one finite element code illustrated the value of establishing benchmark solutions.

Making Benchmark Testing Work

ERIC Educational Resources Information Center

Herman, Joan L.; Baker, Eva L.

2005-01-01

Many schools are moving to develop benchmark tests to monitor their students' progress toward state standards throughout the academic year. Benchmark tests can provide the ongoing information that schools need to guide instructional programs and to address student learning problems. The authors discuss six criteria that educators can use to…

Benchmark for Strategic Performance Improvement.

ERIC Educational Resources Information Center

Gohlke, Annette

1997-01-01

Explains benchmarking, a total quality management tool used to measure and compare the work processes in a library with those in other libraries to increase library performance. Topics include the main groups of upper management, clients, and staff; critical success factors for each group; and benefits of benchmarking. (Author/LRW)

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection... 40 Protection of Environment 22 2010-07-01 2010-07-01 false How is the disinfection benchmark...

Internal Benchmarking for Institutional Effectiveness

ERIC Educational Resources Information Center

Ronco, Sharron L.

2012-01-01

Internal benchmarking is an established practice in business and industry for identifying best in-house practices and disseminating the knowledge about those practices to other groups in the organization. Internal benchmarking can be done with structures, processes, outcomes, or even individuals. In colleges or universities with multicampuses or a…

Marking Closely or on the Bench?: An Australian's Benchmark Statement.

ERIC Educational Resources Information Center

Jones, Roy

2000-01-01

Reviews the benchmark statements of the Quality Assurance Agency for Higher Education in the United Kingdom. Examines the various sections within the benchmark. States that in terms of emphasizing the positive attributes of the geography discipline the statements have wide utility and applicability. (CMK)

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 11 2012-01-01 2012-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 11 2014-01-01 2014-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 11 2011-01-01 2011-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 11 2013-01-01 2013-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sample, B.E. Opresko, D.M. Suter, G.W.

Ecological risks of environmental contaminants are evaluated by using a two-tiered process. In the first tier, a screening assessment is performed where concentrations of contaminants in the environment are compared to no observed adverse effects level (NOAEL)-based toxicological benchmarks. These benchmarks represent concentrations of chemicals (i.e., concentrations presumed to be nonhazardous to the biota) in environmental media (water, sediment, soil, food, etc.). While exceedance of these benchmarks does not indicate any particular level or type of risk, concentrations below the benchmarks should not result in significant effects. In practice, when contaminant concentrations in food or water resources are less thanmore » these toxicological benchmarks, the contaminants may be excluded from further consideration. However, if the concentration of a contaminant exceeds a benchmark, that contaminant should be retained as a contaminant of potential concern (COPC) and investigated further. The second tier in ecological risk assessment, the baseline ecological risk assessment, may use toxicological benchmarks as part of a weight-of-evidence approach (Suter 1993). Under this approach, based toxicological benchmarks are one of several lines of evidence used to support or refute the presence of ecological effects. Other sources of evidence include media toxicity tests, surveys of biota (abundance and diversity), measures of contaminant body burdens, and biomarkers. This report presents NOAEL- and lowest observed adverse effects level (LOAEL)-based toxicological benchmarks for assessment of effects of 85 chemicals on 9 representative mammalian wildlife species (short-tailed shrew, little brown bat, meadow vole, white-footed mouse, cottontail rabbit, mink, red fox, and whitetail deer) or 11 avian wildlife species (American robin, rough-winged swallow, American woodcock, wild turkey, belted kingfisher, great blue heron, barred owl, barn owl, Cooper's hawk, and red-tailed hawk, osprey) (scientific names for both the mammalian and avian species are presented in Appendix B). [In this document, NOAEL refers to both dose (mg contaminant per kg animal body weight per day) and concentration (mg contaminant per kg of food or L of drinking water)]. The 20 wildlife species were chosen because they are widely distributed and provide a representative range of body sizes and diets. The chemicals are some of those that occur at U.S. Department of Energy (DOE) waste sites. The NOAEL-based benchmarks presented in this report represent values believed to be nonhazardous for the listed wildlife species; LOAEL-based benchmarks represent threshold levels at which adverse effects are likely to become evident. These benchmarks consider contaminant exposure through oral ingestion of contaminated media only. Exposure through inhalation and/or direct dermal exposure are not considered in this report.« less

Benchmark levels for the consumptive water footprint of crop production for different environmental conditions: a case study for winter wheat in China

NASA Astrophysics Data System (ADS)

Zhuo, La; Mekonnen, Mesfin M.; Hoekstra, Arjen Y.

2016-11-01

Meeting growing food demands while simultaneously shrinking the water footprint (WF) of agricultural production is one of the greatest societal challenges. Benchmarks for the WF of crop production can serve as a reference and be helpful in setting WF reduction targets. The consumptive WF of crops, the consumption of rainwater stored in the soil (green WF), and the consumption of irrigation water (blue WF) over the crop growing period varies spatially and temporally depending on environmental factors like climate and soil. The study explores which environmental factors should be distinguished when determining benchmark levels for the consumptive WF of crops. Hereto we determine benchmark levels for the consumptive WF of winter wheat production in China for all separate years in the period 1961-2008, for rain-fed vs. irrigated croplands, for wet vs. dry years, for warm vs. cold years, for four different soil classes, and for two different climate zones. We simulate consumptive WFs of winter wheat production with the crop water productivity model AquaCrop at a 5 by 5 arcmin resolution, accounting for water stress only. The results show that (i) benchmark levels determined for individual years for the country as a whole remain within a range of ±20 % around long-term mean levels over 1961-2008, (ii) the WF benchmarks for irrigated winter wheat are 8-10 % larger than those for rain-fed winter wheat, (iii) WF benchmarks for wet years are 1-3 % smaller than for dry years, (iv) WF benchmarks for warm years are 7-8 % smaller than for cold years, (v) WF benchmarks differ by about 10-12 % across different soil texture classes, and (vi) WF benchmarks for the humid zone are 26-31 % smaller than for the arid zone, which has relatively higher reference evapotranspiration in general and lower yields in rain-fed fields. We conclude that when determining benchmark levels for the consumptive WF of a crop, it is useful to primarily distinguish between different climate zones. If actual consumptive WFs of winter wheat throughout China were reduced to the benchmark levels set by the best 25 % of Chinese winter wheat production (1224 m3 t-1 for arid areas and 841 m3 t-1 for humid areas), the water saving in an average year would be 53 % of the current water consumption at winter wheat fields in China. The majority of the yield increase and associated improvement in water productivity can be achieved in southern China.

Benchmarks for Psychotherapy Efficacy in Adult Major Depression

ERIC Educational Resources Information Center

Minami, Takuya; Wampold, Bruce E.; Serlin, Ronald C.; Kircher, John C.; Brown, George S.

2007-01-01

This study estimates pretreatment-posttreatment effect size benchmarks for the treatment of major depression in adults that may be useful in evaluating psychotherapy effectiveness in clinical practice. Treatment efficacy benchmarks for major depression were derived for 3 different types of outcome measures: the Hamilton Rating Scale for Depression…

Application of Benchmark Dose Methodology to a Variety of Endpoints and Exposures

EPA Science Inventory

This latest beta version (1.1b) of the U.S. Environmental Protection Agency (EPA) Benchmark Dose Software (BMDS) is being distributed for public comment. The BMDS system is being developed as a tool to facilitate the application of benchmark dose (BMD) methods to EPA hazardous p...

Technical Report: Installed Cost Benchmarks and Deployment Barriers for

Science.gov Websites

Cost Benchmarks and Deployment Barriers for Residential Solar Photovoltaics with Energy Storage Q1 2016 Installed Cost Benchmarks and Deployment Barriers for Residential Solar with Energy Storage Researchers from NREL published a report that provides detailed component and system-level cost breakdowns for

Suck It up

ERIC Educational Resources Information Center

Jansik, Dave

2008-01-01

Benchmarks for cleanliness can be subjective. Now that LEED (Leadership in Energy and Environmental Design) standards are gaining a foothold among facilities management and building professionals, there is a benchmark to strive for and a high-quality vacuum is a key part of the equation. LEED is a nationally accepted benchmark and blueprint for…

Benchmarking Tool Kit.

ERIC Educational Resources Information Center

Canadian Health Libraries Association.

Nine Canadian health libraries participated in a pilot test of the Benchmarking Tool Kit between January and April, 1998. Although the Tool Kit was designed specifically for health libraries, the content and approach are useful to other types of libraries as well. Used to its full potential, benchmarking can provide a common measuring stick to…

Benchmarking: A Process for Improvement.

ERIC Educational Resources Information Center

Peischl, Thomas M.

One problem with the outcome-based measures used in higher education is that they measure quantity but not quality. Benchmarking, or the use of some external standard of quality to measure tasks, processes, and outputs, is partially solving that difficulty. Benchmarking allows for the establishment of a systematic process to indicate if outputs…

Establishing Benchmarks for Outcome Indicators: A Statistical Approach to Developing Performance Standards.

ERIC Educational Resources Information Center

Henry, Gary T.; And Others

1992-01-01

A statistical technique is presented for developing performance standards based on benchmark groups. The benchmark groups are selected using a multivariate technique that relies on a squared Euclidean distance method. For each observation unit (a school district in the example), a unique comparison group is selected. (SLD)

47 CFR 69.108 - Transport rate benchmark.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false Transport rate benchmark. 69.108 Section 69.108... Computation of Charges § 69.108 Transport rate benchmark. (a) For transport charges computed in accordance... interoffice transmission using the telephone company's DS1 special access rates. (b) Initial transport rates...

47 CFR 69.108 - Transport rate benchmark.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 3 2011-10-01 2011-10-01 false Transport rate benchmark. 69.108 Section 69.108... Computation of Charges § 69.108 Transport rate benchmark. (a) For transport charges computed in accordance... interoffice transmission using the telephone company's DS1 special access rates. (b) Initial transport rates...

Apples to Oranges: Benchmarking Vocational Education and Training Programmes

ERIC Educational Resources Information Center

Bogetoft, Peter; Wittrup, Jesper

2017-01-01

This paper discusses methods for benchmarking vocational education and training colleges and presents results from a number of models. It is conceptually difficult to benchmark vocational colleges. The colleges typically offer a wide range of course programmes, and the students come from different socioeconomic backgrounds. We solve the…

Beyond Benchmarking: Value-Adding Metrics

ERIC Educational Resources Information Center

Fitz-enz, Jac

2007-01-01

HR metrics has grown up a bit over the past two decades, moving away from simple benchmarking practices and toward a more inclusive approach to measuring institutional performance and progress. In this article, the acknowledged "father" of human capital performance benchmarking provides an overview of several aspects of today's HR metrics…

Benchmarking with the BLASST Sessional Staff Standards Framework

ERIC Educational Resources Information Center

Luzia, Karina; Harvey, Marina; Parker, Nicola; McCormack, Coralie; Brown, Natalie R.

2013-01-01

Benchmarking as a type of knowledge-sharing around good practice within and between institutions is increasingly common in the higher education sector. More recently, benchmarking as a process that can contribute to quality enhancement has been deployed across numerous institutions with a view to systematising frameworks to assure and enhance the…

Using Institutional Survey Data to Jump-Start Your Benchmarking Process

ERIC Educational Resources Information Center

Chow, Timothy K. C.

2012-01-01

Guided by the missions and visions, higher education institutions utilize benchmarking processes to identify better and more efficient ways to carry out their operations. Aside from the initial planning and organization steps involved in benchmarking, a matching or selection step is crucial for identifying other institutions that have good…

Practical Considerations when Using Benchmarking for Accountability in Higher Education

ERIC Educational Resources Information Center

Achtemeier, Sue D.; Simpson, Ronald D.

2005-01-01

The qualitative study on which this article is based examined key individuals' perceptions, both within a research university community and beyond in its external governing board, of how to improve benchmarking as an accountability method in higher education. Differing understanding of benchmarking revealed practical implications for using it as…

75 FR 82115 - Self-Regulatory Organizations; National Securities Clearing Corporation; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-29

... to provide more efficient, cost-effective, and timely benchmarking and other market information about.... This market analysis (commonly referred to as ``benchmarking'') would allow users of this service to... determine to be most useful. The benchmarking portion of the service would provide information on an...

Benchmarking in the Two-Year Public Postsecondary Sector: A Learning Process

ERIC Educational Resources Information Center

Mitchell, Jennevieve

2015-01-01

The recession prompted reflection on how resource allocation decisions contribute to the performance of community colleges in the United States. Private benchmarking initiatives, most notably those established by the National Higher Education Benchmarking Institute, can only partially begin to address this question. Empirical and financial…

76 FR 54807 - Submission of OMB Review: Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... Benchmarking Survey Submission of OMB Review: Comment Request The National Endowment for the Arts (NEA) has... the Arts. Title: Annual Arts Benchmarking Survey. OMB Number: New. Frequency: Annually, in years the... Purchasing Services): 0. This request is for clearance of the Annual Arts Benchmarking Survey (AABS) to be...

BENCHMARK DOSES FOR CHEMICAL MIXTURES: EVALUATION OF A MIXTURE OF 18 PHAHS.

EPA Science Inventory

Benchmark doses (BMDs), defined as doses of a substance that are expected to result in a pre-specified level of "benchmark" response (BMR), have been used for quantifying the risk associated with exposure to environmental hazards. The lower confidence limit of the BMD is used as...

What Are the ACT College Readiness Benchmarks? Information Brief

ERIC Educational Resources Information Center

ACT, Inc., 2013

2013-01-01

The ACT College Readiness Benchmarks are the minimum ACT® college readiness assessment scores required for students to have a high probability of success in credit-bearing college courses--English Composition, social sciences courses, College Algebra, or Biology. This report identifies the College Readiness Benchmarks on the ACT Compass scale…

The NAS kernel benchmark program

NASA Technical Reports Server (NTRS)

Bailey, D. H.; Barton, J. T.

1985-01-01

A collection of benchmark test kernels that measure supercomputer performance has been developed for the use of the NAS (Numerical Aerodynamic Simulation) program at the NASA Ames Research Center. This benchmark program is described in detail and the specific ground rules are given for running the program as a performance test.

Electric-Drive Vehicle Thermal Performance Benchmarking | Transportation

Science.gov Websites

studies are as follows: Characterize the thermal resistance and conductivity of various layers in the Research | NREL Electric-Drive Vehicle Thermal Performance Benchmarking Electric-Drive Vehicle Thermal Performance Benchmarking A photo of the internal components of an automotive inverter. NREL

42 CFR 440.320 - State plan requirements: Optional enrollment for exempt individuals.

Code of Federal Regulations, 2010 CFR

2010-10-01

... benchmark or benchmark-equivalent benefit package, the State must effectively inform the individual prior to...-equivalent benefit package and the costs under such a package and provide a comparison of how they differ... benchmark-equivalent benefit package. (4) For individuals who the State determines have become exempt...

42 CFR 440.320 - State plan requirements: Optional enrollment for exempt individuals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... benchmark or benchmark-equivalent benefit package, the State must effectively inform the individual prior to...-equivalent benefit package and the costs under such a package and provide a comparison of how they differ... benchmark-equivalent benefit package. (4) For individuals who the State determines have become exempt...

42 CFR 440.320 - State plan requirements: Optional enrollment for exempt individuals.

Code of Federal Regulations, 2012 CFR

2012-10-01

... benchmark or benchmark-equivalent benefit package, the State must effectively inform the individual prior to...-equivalent benefit package and the costs under such a package and provide a comparison of how they differ... benchmark-equivalent benefit package. (4) For individuals who the State determines have become exempt...

42 CFR 440.320 - State plan requirements: Optional enrollment for exempt individuals.

Code of Federal Regulations, 2013 CFR

2013-10-01

... benchmark or benchmark-equivalent benefit package, the State must effectively inform the individual prior to...-equivalent benefit package and the costs under such a package and provide a comparison of how they differ... benchmark-equivalent benefit package. (4) For individuals who the State determines have become exempt...

42 CFR 440.320 - State plan requirements: Optional enrollment for exempt individuals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... benchmark or benchmark-equivalent benefit package, the State must effectively inform the individual prior to...-equivalent benefit package and the costs under such a package and provide a comparison of how they differ... benchmark-equivalent benefit package. (4) For individuals who the State determines have become exempt...

[Benchmarking of university trauma centers in Germany. Research and teaching].

PubMed

Gebhard, F; Raschke, M; Ruchholtz, S; Meffert, R; Marzi, I; Pohlemann, T; Südkamp, N; Josten, C; Zwipp, H

2011-07-01

Benchmarking is a very popular business process and meanwhile is used in research as well. The aim of the present study is to elucidate key numbers of German university trauma departments regarding research and teaching. The data set is based upon the monthly reports given by the administration in each university. As a result the study shows that only well-known parameters such as fund-raising and impact factors can be used to benchmark university-based trauma centers. The German federal system does not allow a nationwide benchmarking.

An analytical benchmark and a Mathematica program for MD codes: Testing LAMMPS on the 2nd generation Brenner potential

NASA Astrophysics Data System (ADS)

Favata, Antonino; Micheletti, Andrea; Ryu, Seunghwa; Pugno, Nicola M.

2016-10-01

An analytical benchmark and a simple consistent Mathematica program are proposed for graphene and carbon nanotubes, that may serve to test any molecular dynamics code implemented with REBO potentials. By exploiting the benchmark, we checked results produced by LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator) when adopting the second generation Brenner potential, we made evident that this code in its current implementation produces results which are offset from those of the benchmark by a significant amount, and provide evidence of the reason.

Benchmarking gate-based quantum computers

NASA Astrophysics Data System (ADS)

Michielsen, Kristel; Nocon, Madita; Willsch, Dennis; Jin, Fengping; Lippert, Thomas; De Raedt, Hans

2017-11-01

With the advent of public access to small gate-based quantum processors, it becomes necessary to develop a benchmarking methodology such that independent researchers can validate the operation of these processors. We explore the usefulness of a number of simple quantum circuits as benchmarks for gate-based quantum computing devices and show that circuits performing identity operations are very simple, scalable and sensitive to gate errors and are therefore very well suited for this task. We illustrate the procedure by presenting benchmark results for the IBM Quantum Experience, a cloud-based platform for gate-based quantum computing.

Toward Scalable Benchmarks for Mass Storage Systems

NASA Technical Reports Server (NTRS)

Miller, Ethan L.

1996-01-01

This paper presents guidelines for the design of a mass storage system benchmark suite, along with preliminary suggestions for programs to be included. The benchmarks will measure both peak and sustained performance of the system as well as predicting both short- and long-term behavior. These benchmarks should be both portable and scalable so they may be used on storage systems from tens of gigabytes to petabytes or more. By developing a standard set of benchmarks that reflect real user workload, we hope to encourage system designers and users to publish performance figures that can be compared with those of other systems. This will allow users to choose the system that best meets their needs and give designers a tool with which they can measure the performance effects of improvements to their systems.

Clomp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gylenhaal, J.; Bronevetsky, G.

2007-05-25

CLOMP is the C version of the Livermore OpenMP benchmark deeloped to measure OpenMP overheads and other performance impacts due to threading (like NUMA memory layouts, memory contention, cache effects, etc.) in order to influence future system design. Current best-in-class implementations of OpenMP have overheads at least ten times larger than is required by many of our applications for effective use of OpenMP. This benchmark shows the significant negative performance impact of these relatively large overheads and of other thread effects. The CLOMP benchmark highly configurable to allow a variety of problem sizes and threading effects to be studied andmore » it carefully checks its results to catch many common threading errors. This benchmark is expected to be included as part of the Sequoia Benchmark suite for the Sequoia procurement.« less

Benchmarking and validation activities within JEFF project

NASA Astrophysics Data System (ADS)

Cabellos, O.; Alvarez-Velarde, F.; Angelone, M.; Diez, C. J.; Dyrda, J.; Fiorito, L.; Fischer, U.; Fleming, M.; Haeck, W.; Hill, I.; Ichou, R.; Kim, D. H.; Klix, A.; Kodeli, I.; Leconte, P.; Michel-Sendis, F.; Nunnenmann, E.; Pecchia, M.; Peneliau, Y.; Plompen, A.; Rochman, D.; Romojaro, P.; Stankovskiy, A.; Sublet, J. Ch.; Tamagno, P.; Marck, S. van der

2017-09-01

The challenge for any nuclear data evaluation project is to periodically release a revised, fully consistent and complete library, with all needed data and covariances, and ensure that it is robust and reliable for a variety of applications. Within an evaluation effort, benchmarking activities play an important role in validating proposed libraries. The Joint Evaluated Fission and Fusion (JEFF) Project aims to provide such a nuclear data library, and thus, requires a coherent and efficient benchmarking process. The aim of this paper is to present the activities carried out by the new JEFF Benchmarking and Validation Working Group, and to describe the role of the NEA Data Bank in this context. The paper will also review the status of preliminary benchmarking for the next JEFF-3.3 candidate cross-section files.

Using a health promotion model to promote benchmarking.

PubMed

Welby, Jane

2006-07-01

The North East (England) Neonatal Benchmarking Group has been established for almost a decade and has researched and developed a substantial number of evidence-based benchmarks. With no firm evidence that these were being used or that there was any standardisation of neonatal care throughout the region, the group embarked on a programme to review the benchmarks and determine what evidence-based guidelines were needed to support standardisation. A health promotion planning model was used by one subgroup to structure the programme; it enabled all members of the sub group to engage in the review process and provided the motivation and supporting documentation for implementation of changes in practice. The need for a regional guideline development group to complement the activity of the benchmarking group is being addressed.

Benchmarks for effective primary care-based nursing services for adults with depression: a Delphi study.

PubMed

McIlrath, Carole; Keeney, Sinead; McKenna, Hugh; McLaughlin, Derek

2010-02-01

This paper is a report of a study conducted to identify and gain consensus on appropriate benchmarks for effective primary care-based nursing services for adults with depression. Worldwide evidence suggests that between 5% and 16% of the population have a diagnosis of depression. Most of their care and treatment takes place in primary care. In recent years, primary care nurses, including community mental health nurses, have become more involved in the identification and management of patients with depression; however, there are no appropriate benchmarks to guide, develop and support their practice. In 2006, a three-round electronic Delphi survey was completed by a United Kingdom multi-professional expert panel (n = 67). Round 1 generated 1216 statements relating to structures (such as training and protocols), processes (such as access and screening) and outcomes (such as patient satisfaction and treatments). Content analysis was used to collapse statements into 140 benchmarks. Seventy-three benchmarks achieved consensus during subsequent rounds. Of these, 45 (61%) were related to structures, 18 (25%) to processes and 10 (14%) to outcomes. Multi-professional primary care staff have similar views about the appropriate benchmarks for care of adults with depression. These benchmarks could serve as a foundation for depression improvement initiatives in primary care and ongoing research into depression management by nurses.

Benchmarking infrastructure for mutation text mining

PubMed Central

2014-01-01

Background Experimental research on the automatic extraction of information about mutations from texts is greatly hindered by the lack of consensus evaluation infrastructure for the testing and benchmarking of mutation text mining systems. Results We propose a community-oriented annotation and benchmarking infrastructure to support development, testing, benchmarking, and comparison of mutation text mining systems. The design is based on semantic standards, where RDF is used to represent annotations, an OWL ontology provides an extensible schema for the data and SPARQL is used to compute various performance metrics, so that in many cases no programming is needed to analyze results from a text mining system. While large benchmark corpora for biological entity and relation extraction are focused mostly on genes, proteins, diseases, and species, our benchmarking infrastructure fills the gap for mutation information. The core infrastructure comprises (1) an ontology for modelling annotations, (2) SPARQL queries for computing performance metrics, and (3) a sizeable collection of manually curated documents, that can support mutation grounding and mutation impact extraction experiments. Conclusion We have developed the principal infrastructure for the benchmarking of mutation text mining tasks. The use of RDF and OWL as the representation for corpora ensures extensibility. The infrastructure is suitable for out-of-the-box use in several important scenarios and is ready, in its current state, for initial community adoption. PMID:24568600

Benchmarking infrastructure for mutation text mining.

PubMed

Klein, Artjom; Riazanov, Alexandre; Hindle, Matthew M; Baker, Christopher Jo

2014-02-25

Experimental research on the automatic extraction of information about mutations from texts is greatly hindered by the lack of consensus evaluation infrastructure for the testing and benchmarking of mutation text mining systems. We propose a community-oriented annotation and benchmarking infrastructure to support development, testing, benchmarking, and comparison of mutation text mining systems. The design is based on semantic standards, where RDF is used to represent annotations, an OWL ontology provides an extensible schema for the data and SPARQL is used to compute various performance metrics, so that in many cases no programming is needed to analyze results from a text mining system. While large benchmark corpora for biological entity and relation extraction are focused mostly on genes, proteins, diseases, and species, our benchmarking infrastructure fills the gap for mutation information. The core infrastructure comprises (1) an ontology for modelling annotations, (2) SPARQL queries for computing performance metrics, and (3) a sizeable collection of manually curated documents, that can support mutation grounding and mutation impact extraction experiments. We have developed the principal infrastructure for the benchmarking of mutation text mining tasks. The use of RDF and OWL as the representation for corpora ensures extensibility. The infrastructure is suitable for out-of-the-box use in several important scenarios and is ready, in its current state, for initial community adoption.

Research on computer systems benchmarking

NASA Technical Reports Server (NTRS)

Smith, Alan Jay (Principal Investigator)

1996-01-01

This grant addresses the topic of research on computer systems benchmarking and is more generally concerned with performance issues in computer systems. This report reviews work in those areas during the period of NASA support under this grant. The bulk of the work performed concerned benchmarking and analysis of CPUs, compilers, caches, and benchmark programs. The first part of this work concerned the issue of benchmark performance prediction. A new approach to benchmarking and machine characterization was reported, using a machine characterizer that measures the performance of a given system in terms of a Fortran abstract machine. Another report focused on analyzing compiler performance. The performance impact of optimization in the context of our methodology for CPU performance characterization was based on the abstract machine model. Benchmark programs are analyzed in another paper. A machine-independent model of program execution was developed to characterize both machine performance and program execution. By merging these machine and program characterizations, execution time can be estimated for arbitrary machine/program combinations. The work was continued into the domain of parallel and vector machines, including the issue of caches in vector processors and multiprocessors. All of the afore-mentioned accomplishments are more specifically summarized in this report, as well as those smaller in magnitude supported by this grant.

Dynamic breaking of a single gold bond

NASA Astrophysics Data System (ADS)

Pobelov, Ilya V.; Lauritzen, Kasper Primdal; Yoshida, Koji; Jensen, Anders; Mészáros, Gábor; Jacobsen, Karsten W.; Strange, Mikkel; Wandlowski, Thomas; Solomon, Gemma C.

2017-07-01

While one might assume that the force to break a chemical bond gives a measure of the bond strength, this intuition is misleading. If the force is loaded slowly, thermal fluctuations may break the bond before it is maximally stretched, and the breaking force will be less than the bond can sustain. Conversely, if the force is loaded rapidly it is more likely that the maximum breaking force is measured. Paradoxically, no clear differences in breaking force were observed in experiments on gold nanowires, despite being conducted under very different conditions. Here we explore the breaking behaviour of a single Au-Au bond and show that the breaking force is dependent on the loading rate. We probe the temperature and structural dependencies of breaking and suggest that the paradox can be explained by fast breaking of atomic wires and slow breaking of point contacts giving very similar breaking forces.

78 FR 47671 - Proposed Information Collection; Comment Request; Benchmark Survey of Insurance Transactions by U...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... Request; Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons...: I. Abstract Form BE-140, Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons, obtains annual data from all U.S. insurance companies that engage in the following...

Benchmarks and Quality Assurance for Online Course Development in Higher Education

ERIC Educational Resources Information Center

Wang, Hong

2008-01-01

As online education has entered the main stream of the U.S. higher education, quality assurance in online course development has become a critical topic in distance education. This short article summarizes the major benchmarks related to online course development, listing and comparing the benchmarks of the National Education Association (NEA),…

MARC calculations for the second WIPP structural benchmark problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, H.S.

1981-05-01

This report describes calculations made with the MARC structural finite element code for the second WIPP structural benchmark problem. Specific aspects of problem implementation such as element choice, slip line modeling, creep law implementation, and thermal-mechanical coupling are discussed in detail. Also included are the computational results specified in the benchmark problem formulation.

Benchmarking as a Global Strategy for Improving Instruction in Higher Education.

ERIC Educational Resources Information Center

Clark, Karen L.

This paper explores the concept of benchmarking in institutional research, a comparative analysis methodology designed to help colleges and universities increase their educational quality and delivery systems. The primary purpose of benchmarking is to compare an institution to its competitors in order to improve the product (in this case…

Benchmarking and beyond. Information trends in home care.

PubMed

Twiss, Amanda; Rooney, Heather; Lang, Christine

2002-11-01

With today's benchmarking concepts and tools, agencies have the unprecedented opportunity to use information as a strategic advantage. Because agencies are demanding more and better information, benchmark functionality has grown increasingly sophisticated. Agencies now require a new type of analysis, focused on high-level executive summaries while reducing the current "data overload."

75 FR 26057 - Mandatory Reliability Standards for the Calculation of Available Transfer Capability, Capacity...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-11

... Requirement R3.1 of MOD-001-1. C. Benchmarking 14. In the Final Rule, the Commission directed the ERO to develop benchmarking and updating requirements for the MOD Reliability Standards to measure modeled... requirements should specify the frequency for benchmarking and updating the available transfer and flowgate...

Development of a Computer-based Benchmarking and Analytical Tool. Benchmarking and Energy & Water Savings Tool in Dairy Plants (BEST-Dairy)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Tengfang; Flapper, Joris; Ke, Jing

The overall goal of the project is to develop a computer-based benchmarking and energy and water savings tool (BEST-Dairy) for use in the California dairy industry – including four dairy processes – cheese, fluid milk, butter, and milk powder.

Within-Group Effect-Size Benchmarks for Trauma-Focused Cognitive Behavioral Therapy with Children and Adolescents

ERIC Educational Resources Information Center

Rubin, Allen; Washburn, Micki; Schieszler, Christine

2017-01-01

Purpose: This article provides benchmark data on within-group effect sizes from published randomized clinical trials (RCTs) supporting the efficacy of trauma-focused cognitive behavioral therapy (TF-CBT) for traumatized children. Methods: Within-group effect-size benchmarks for symptoms of trauma, anxiety, and depression were calculated via the…

47 CFR 54.805 - Zone and study area above benchmark revenues calculated by the Administrator.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Period Residential and Single-Line Business Lines times 12. If negative, the Zone Above Benchmark...) multiplied by all eligible telecommunications carrier zone Base Period Multi-line Business Lines times 12. If... 47 Telecommunication 3 2010-10-01 2010-10-01 false Zone and study area above benchmark revenues...

Issues in Institutional Benchmarking of Student Learning Outcomes Using Case Examples

ERIC Educational Resources Information Center

Judd, Thomas P.; Pondish, Christopher; Secolsky, Charles

2013-01-01

Benchmarking is a process that can take place at both the inter-institutional and intra-institutional level. This paper focuses on benchmarking intra-institutional student learning outcomes using case examples. The findings of the study illustrate the point that when the outcomes statements associated with the mission of the institution are…

Benchmarking in TESOL: A Study of the Malaysia Education Blueprint 2013

ERIC Educational Resources Information Center

Jawaid, Arif

2014-01-01

Benchmarking is a very common real-life function occurring every moment unnoticed. It has travelled from industry to education like other quality disciplines. Initially benchmarking was used in higher education. .Now it is diffusing into other areas including TESOL (Teaching English to Speakers of Other Languages), which has yet to devise a…

Analysis of a benchmark suite to evaluate mixed numeric and symbolic processing

NASA Technical Reports Server (NTRS)

Ragharan, Bharathi; Galant, David

1992-01-01

The suite of programs that formed the benchmark for a proposed advanced computer is described and analyzed. The features of the processor and its operating system that are tested by the benchmark are discussed. The computer codes and the supporting data for the analysis are given as appendices.

Benchmarking in Czech Higher Education: The Case of Schools of Economics

ERIC Educational Resources Information Center

Placek, Michal; Ochrana, František; Pucek, Milan

2015-01-01

This article describes the use of benchmarking in universities in the Czech Republic and academics' experiences with it. It is based on research conducted among academics from economics schools in Czech public and private universities. The results identified several issues regarding the utilisation and understanding of benchmarking in the Czech…

Learning Through Benchmarking: Developing a Relational, Prospective Approach to Benchmarking ICT in Learning and Teaching

ERIC Educational Resources Information Center

Ellis, Robert A.; Moore, Roger R.

2006-01-01

This study discusses benchmarking the use of information and communication technologies (ICT) in teaching and learning between two universities with different missions: one an Australian campus-based metropolitan university and the other a British distance-education provider. It argues that the differences notwithstanding, it is possible to…

Benchmark Factors in Student Retention.

ERIC Educational Resources Information Center

Waggener, Anna T.; Smith, Constance K.

The first purpose of this study was to identify significant factors affecting the first benchmark in retaining students in college--the decision to enroll in the first fall semester after orientation. The second purpose was to examine enrollment decisions at the second benchmark--the decision to re-enroll in the second fall semester after freshman…

Rural Elementary Students' Understanding of Science and Agricultural Education Benchmarks Related to Meat and Livestock.

ERIC Educational Resources Information Center

Meischen, Deanna L.; Trexler, Cary J.

2003-01-01

Seven fifth-graders developed concept maps depicting their knowledge of meat product development. Despite their rural background, they lacked understanding of agriculture concepts and had mixed knowledge of agricultural literacy benchmarks concerning food products. Their language did not reflect scientific terminology in the benchmarks. (Contains…

Outcome Benchmarks for Adaptations of Research-Supported Treatments for Adult Traumatic Stress

ERIC Educational Resources Information Center

Rubin, Allen; Parrish, Danielle E.; Washburn, Micki

2016-01-01

This article provides benchmark data on within-group effect sizes from published randomized controlled trials (RCTs) that evaluated the efficacy of research-supported treatments (RSTs) for adult traumatic stress. Agencies can compare these benchmarks to their treatment group effect size to inform their decisions as to whether the way they are…

IT-benchmarking of clinical workflows: concept, implementation, and evaluation.

PubMed

Thye, Johannes; Straede, Matthias-Christopher; Liebe, Jan-David; Hübner, Ursula

2014-01-01

Due to the emerging evidence of health IT as opportunity and risk for clinical workflows, health IT must undergo a continuous measurement of its efficacy and efficiency. IT-benchmarks are a proven means for providing this information. The aim of this study was to enhance the methodology of an existing benchmarking procedure by including, in particular, new indicators of clinical workflows and by proposing new types of visualisation. Drawing on the concept of information logistics, we propose four workflow descriptors that were applied to four clinical processes. General and specific indicators were derived from these descriptors and processes. 199 chief information officers (CIOs) took part in the benchmarking. These hospitals were assigned to reference groups of a similar size and ownership from a total of 259 hospitals. Stepwise and comprehensive feedback was given to the CIOs. Most participants who evaluated the benchmark rated the procedure as very good, good, or rather good (98.4%). Benchmark information was used by CIOs for getting a general overview, advancing IT, preparing negotiations with board members, and arguing for a new IT project.

Development and Application of Benchmark Examples for Mixed-Mode I/II Quasi-Static Delamination Propagation Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2012-01-01

The development of benchmark examples for quasi-static delamination propagation prediction is presented. The example is based on a finite element model of the Mixed-Mode Bending (MMB) specimen for 50% mode II. The benchmarking is demonstrated for Abaqus/Standard, however, the example is independent of the analysis software used and allows the assessment of the automated delamination propagation prediction capability in commercial finite element codes based on the virtual crack closure technique (VCCT). First, a quasi-static benchmark example was created for the specimen. Second, starting from an initially straight front, the delamination was allowed to propagate under quasi-static loading. Third, the load-displacement as well as delamination length versus applied load/displacement relationships from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Overall, the results are encouraging, but further assessment for mixed-mode delamination fatigue onset and growth is required.

Quality management benchmarking: FDA compliance in pharmaceutical industry.

PubMed

Jochem, Roland; Landgraf, Katja

2010-01-01

By analyzing and comparing industry and business best practice, processes can be optimized and become more successful mainly because efficiency and competitiveness increase. This paper aims to focus on some examples. Case studies are used to show knowledge exchange in the pharmaceutical industry. Best practice solutions were identified in two companies using a benchmarking method and five-stage model. Despite large administrations, there is much potential regarding business process organization. This project makes it possible for participants to fully understand their business processes. The benchmarking method gives an opportunity to critically analyze value chains (a string of companies or players working together to satisfy market demands for a special product). Knowledge exchange is interesting for companies that like to be global players. Benchmarking supports information exchange and improves competitive ability between different enterprises. Findings suggest that the five-stage model improves efficiency and effectiveness. Furthermore, the model increases the chances for reaching targets. The method gives security to partners that did not have benchmarking experience. The study identifies new quality management procedures. Process management and especially benchmarking is shown to support pharmaceutical industry improvements.

Benchmarking child and adolescent mental health organizations.

PubMed

Brann, Peter; Walter, Garry; Coombs, Tim

2011-04-01

This paper describes aspects of the child and adolescent benchmarking forums that were part of the National Mental Health Benchmarking Project (NMHBP). These forums enabled participating child and adolescent mental health organizations to benchmark themselves against each other, with a view to understanding variability in performance against a range of key performance indicators (KPIs). Six child and adolescent mental health organizations took part in the NMHBP. Representatives from these organizations attended eight benchmarking forums at which they documented their performance against relevant KPIs. They also undertook two special projects designed to help them understand the variation in performance on given KPIs. There was considerable inter-organization variability on many of the KPIs. Even within organizations, there was often substantial variability over time. The variability in indicator data raised many questions for participants. This challenged participants to better understand and describe their local processes, prompted them to collect additional data, and stimulated them to make organizational comparisons. These activities fed into a process of reflection about their performance. Benchmarking has the potential to illuminate intra- and inter-organizational performance in the child and adolescent context.

Issues in benchmarking human reliability analysis methods : a literature review.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lois, Erasmia; Forester, John Alan; Tran, Tuan Q.

There is a diversity of human reliability analysis (HRA) methods available for use in assessing human performance within probabilistic risk assessment (PRA). Due to the significant differences in the methods, including the scope, approach, and underlying models, there is a need for an empirical comparison investigating the validity and reliability of the methods. To accomplish this empirical comparison, a benchmarking study is currently underway that compares HRA methods with each other and against operator performance in simulator studies. In order to account for as many effects as possible in the construction of this benchmarking study, a literature review was conducted,more » reviewing past benchmarking studies in the areas of psychology and risk assessment. A number of lessons learned through these studies are presented in order to aid in the design of future HRA benchmarking endeavors.« less

Issues in Benchmarking Human Reliability Analysis Methods: A Literature Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ronald L. Boring; Stacey M. L. Hendrickson; John A. Forester

There is a diversity of human reliability analysis (HRA) methods available for use in assessing human performance within probabilistic risk assessments (PRA). Due to the significant differences in the methods, including the scope, approach, and underlying models, there is a need for an empirical comparison investigating the validity and reliability of the methods. To accomplish this empirical comparison, a benchmarking study comparing and evaluating HRA methods in assessing operator performance in simulator experiments is currently underway. In order to account for as many effects as possible in the construction of this benchmarking study, a literature review was conducted, reviewing pastmore » benchmarking studies in the areas of psychology and risk assessment. A number of lessons learned through these studies are presented in order to aid in the design of future HRA benchmarking endeavors.« less

The philosophy of benchmark testing a standards-based picture archiving and communications system.

PubMed

Richardson, N E; Thomas, J A; Lyche, D K; Romlein, J; Norton, G S; Dolecek, Q E

1999-05-01

The Department of Defense issued its requirements for a Digital Imaging Network-Picture Archiving and Communications System (DIN-PACS) in a Request for Proposals (RFP) to industry in January 1997, with subsequent contracts being awarded in November 1997 to the Agfa Division of Bayer and IBM Global Government Industry. The Government's technical evaluation process consisted of evaluating a written technical proposal as well as conducting a benchmark test of each proposed system at the vendor's test facility. The purpose of benchmark testing was to evaluate the performance of the fully integrated system in a simulated operational environment. The benchmark test procedures and test equipment were developed through a joint effort between the Government, academic institutions, and private consultants. Herein the authors discuss the resources required and the methods used to benchmark test a standards-based PACS.

XWeB: The XML Warehouse Benchmark

NASA Astrophysics Data System (ADS)

Mahboubi, Hadj; Darmont, Jérôme

With the emergence of XML as a standard for representing business data, new decision support applications are being developed. These XML data warehouses aim at supporting On-Line Analytical Processing (OLAP) operations that manipulate irregular XML data. To ensure feasibility of these new tools, important performance issues must be addressed. Performance is customarily assessed with the help of benchmarks. However, decision support benchmarks do not currently support XML features. In this paper, we introduce the XML Warehouse Benchmark (XWeB), which aims at filling this gap. XWeB derives from the relational decision support benchmark TPC-H. It is mainly composed of a test data warehouse that is based on a unified reference model for XML warehouses and that features XML-specific structures, and its associate XQuery decision support workload. XWeB's usage is illustrated by experiments on several XML database management systems.

Implementation of Benchmarking Transportation Logistics Practices and Future Benchmarking Organizations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thrower, A.W.; Patric, J.; Keister, M.

2008-07-01

The purpose of the Office of Civilian Radioactive Waste Management's (OCRWM) Logistics Benchmarking Project is to identify established government and industry practices for the safe transportation of hazardous materials which can serve as a yardstick for design and operation of OCRWM's national transportation system for shipping spent nuclear fuel and high-level radioactive waste to the proposed repository at Yucca Mountain, Nevada. The project will present logistics and transportation practices and develop implementation recommendations for adaptation by the national transportation system. This paper will describe the process used to perform the initial benchmarking study, highlight interim findings, and explain how thesemore » findings are being implemented. It will also provide an overview of the next phase of benchmarking studies. The benchmarking effort will remain a high-priority activity throughout the planning and operational phases of the transportation system. The initial phase of the project focused on government transportation programs to identify those practices which are most clearly applicable to OCRWM. These Federal programs have decades of safe transportation experience, strive for excellence in operations, and implement effective stakeholder involvement, all of which parallel OCRWM's transportation mission and vision. The initial benchmarking project focused on four business processes that are critical to OCRWM's mission success, and can be incorporated into OCRWM planning and preparation in the near term. The processes examined were: transportation business model, contract management/out-sourcing, stakeholder relations, and contingency planning. More recently, OCRWM examined logistics operations of AREVA NC's Business Unit Logistics in France. The next phase of benchmarking will focus on integrated domestic and international commercial radioactive logistic operations. The prospective companies represent large scale shippers and have vast experience in safely and efficiently shipping spent nuclear fuel and other radioactive materials. Additional business processes may be examined in this phase. The findings of these benchmarking efforts will help determine the organizational structure and requirements of the national transportation system. (authors)« less

Rethinking the reference collection: exploring benchmarks and e-book availability.

PubMed

Husted, Jeffrey T; Czechowski, Leslie J

2012-01-01

Librarians in the Health Sciences Library System at the University of Pittsburgh explored the possibility of developing an electronic reference collection that would replace the print reference collection, thus providing access to these valuable materials to a widely dispersed user population. The librarians evaluated the print reference collection and standard collection development lists as potential benchmarks for the electronic collection, and they determined which books were available in electronic format. They decided that the low availability of electronic versions of titles in each benchmark group rendered the creation of an electronic reference collection using either benchmark impractical.

Toxicological Benchmarks for Screening Potential Contaminants of Concern for Effects on Soil and Litter Invertebrates and Heterotrophic Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Will, M.E.

1994-01-01

This report presents a standard method for deriving benchmarks for the purpose of ''contaminant screening,'' performed by comparing measured ambient concentrations of chemicals. The work was performed under Work Breakdown Structure 1.4.12.2.3.04.07.02 (Activity Data Sheet 8304). In addition, this report presents sets of data concerning the effects of chemicals in soil on invertebrates and soil microbial processes, benchmarks for chemicals potentially associated with United States Department of Energy sites, and literature describing the experiments from which data were drawn for benchmark derivation.

International land Model Benchmarking (ILAMB) Package v002.00

DOE Data Explorer

Collier, Nathaniel [Oak Ridge National Laboratory; Hoffman, Forrest M. [Oak Ridge National Laboratory; Mu, Mingquan [University of California, Irvine; Randerson, James T. [University of California, Irvine; Riley, William J. [Lawrence Berkeley National Laboratory

2016-05-09

As a contribution to International Land Model Benchmarking (ILAMB) Project, we are providing new analysis approaches, benchmarking tools, and science leadership. The goal of ILAMB is to assess and improve the performance of land models through international cooperation and to inform the design of new measurement campaigns and field studies to reduce uncertainties associated with key biogeochemical processes and feedbacks. ILAMB is expected to be a primary analysis tool for CMIP6 and future model-data intercomparison experiments. This team has developed initial prototype benchmarking systems for ILAMB, which will be improved and extended to include ocean model metrics and diagnostics.

International land Model Benchmarking (ILAMB) Package v001.00

DOE Data Explorer

Mu, Mingquan [University of California, Irvine; Randerson, James T. [University of California, Irvine; Riley, William J. [Lawrence Berkeley National Laboratory; Hoffman, Forrest M. [Oak Ridge National Laboratory

2016-05-02

As a contribution to International Land Model Benchmarking (ILAMB) Project, we are providing new analysis approaches, benchmarking tools, and science leadership. The goal of ILAMB is to assess and improve the performance of land models through international cooperation and to inform the design of new measurement campaigns and field studies to reduce uncertainties associated with key biogeochemical processes and feedbacks. ILAMB is expected to be a primary analysis tool for CMIP6 and future model-data intercomparison experiments. This team has developed initial prototype benchmarking systems for ILAMB, which will be improved and extended to include ocean model metrics and diagnostics.

Benchmarking expert system tools

NASA Technical Reports Server (NTRS)

Riley, Gary

1988-01-01

As part of its evaluation of new technologies, the Artificial Intelligence Section of the Mission Planning and Analysis Div. at NASA-Johnson has made timing tests of several expert system building tools. Among the production systems tested were Automated Reasoning Tool, several versions of OPS5, and CLIPS (C Language Integrated Production System), an expert system builder developed by the AI section. Also included in the test were a Zetalisp version of the benchmark along with four versions of the benchmark written in Knowledge Engineering Environment, an object oriented, frame based expert system tool. The benchmarks used for testing are studied.

Toward Automated Benchmarking of Atomistic Force Fields: Neat Liquid Densities and Static Dielectric Constants from the ThermoML Data Archive.

PubMed

Beauchamp, Kyle A; Behr, Julie M; Rustenburg, Ariën S; Bayly, Christopher I; Kroenlein, Kenneth; Chodera, John D

2015-10-08

Atomistic molecular simulations are a powerful way to make quantitative predictions, but the accuracy of these predictions depends entirely on the quality of the force field employed. Although experimental measurements of fundamental physical properties offer a straightforward approach for evaluating force field quality, the bulk of this information has been tied up in formats that are not machine-readable. Compiling benchmark data sets of physical properties from non-machine-readable sources requires substantial human effort and is prone to the accumulation of human errors, hindering the development of reproducible benchmarks of force-field accuracy. Here, we examine the feasibility of benchmarking atomistic force fields against the NIST ThermoML data archive of physicochemical measurements, which aggregates thousands of experimental measurements in a portable, machine-readable, self-annotating IUPAC-standard format. As a proof of concept, we present a detailed benchmark of the generalized Amber small-molecule force field (GAFF) using the AM1-BCC charge model against experimental measurements (specifically, bulk liquid densities and static dielectric constants at ambient pressure) automatically extracted from the archive and discuss the extent of data available for use in larger scale (or continuously performed) benchmarks. The results of even this limited initial benchmark highlight a general problem with fixed-charge force fields in the representation low-dielectric environments, such as those seen in binding cavities or biological membranes.

Competency based training in robotic surgery: benchmark scores for virtual reality robotic simulation.

PubMed

Raison, Nicholas; Ahmed, Kamran; Fossati, Nicola; Buffi, Nicolò; Mottrie, Alexandre; Dasgupta, Prokar; Van Der Poel, Henk

2017-05-01

To develop benchmark scores of competency for use within a competency based virtual reality (VR) robotic training curriculum. This longitudinal, observational study analysed results from nine European Association of Urology hands-on-training courses in VR simulation. In all, 223 participants ranging from novice to expert robotic surgeons completed 1565 exercises. Competency was set at 75% of the mean expert score. Benchmark scores for all general performance metrics generated by the simulator were calculated. Assessment exercises were selected by expert consensus and through learning-curve analysis. Three basic skill and two advanced skill exercises were identified. Benchmark scores based on expert performance offered viable targets for novice and intermediate trainees in robotic surgery. Novice participants met the competency standards for most basic skill exercises; however, advanced exercises were significantly more challenging. Intermediate participants performed better across the seven metrics but still did not achieve the benchmark standard in the more difficult exercises. Benchmark scores derived from expert performances offer relevant and challenging scores for trainees to achieve during VR simulation training. Objective feedback allows both participants and trainers to monitor educational progress and ensures that training remains effective. Furthermore, the well-defined goals set through benchmarking offer clear targets for trainees and enable training to move to a more efficient competency based curriculum. © 2016 The Authors BJU International © 2016 BJU International Published by John Wiley & Sons Ltd.

Effectiveness of Social Marketing Interventions to Promote Physical Activity Among Adults: A Systematic Review.

PubMed

Xia, Yuan; Deshpande, Sameer; Bonates, Tiberius

2016-11-01

Social marketing managers promote desired behaviors to an audience by making them tangible in the form of environmental opportunities to enhance benefits and reduce barriers. This study proposed "benchmarks," modified from those found in the past literature, that would match important concepts of the social marketing framework and the inclusion of which would ensure behavior change effectiveness. In addition, we analyzed behavior change interventions on a "social marketing continuum" to assess whether the number of benchmarks and the role of specific benchmarks influence the effectiveness of physical activity promotion efforts. A systematic review of social marketing interventions available in academic studies published between 1997 and 2013 revealed 173 conditions in 92 interventions. Findings based on χ 2 , Mallows' Cp, and Logical Analysis of Data tests revealed that the presence of more benchmarks in interventions increased the likelihood of success in promoting physical activity. The presence of more than 3 benchmarks improved the success of the interventions; specifically, all interventions were successful when more than 7.5 benchmarks were present. Further, primary formative research, core product, actual product, augmented product, promotion, and behavioral competition all had a significant influence on the effectiveness of interventions. Social marketing is an effective approach in promoting physical activity among adults when a substantial number of benchmarks are used and when managers understand the audience, make the desired behavior tangible, and promote the desired behavior persuasively.

[Benchmarking and other functions of ROM: back to basics].

PubMed

Barendregt, M

2015-01-01

Since 2011 outcome data in the Dutch mental health care have been collected on a national scale. This has led to confusion about the position of benchmarking in the system known as routine outcome monitoring (rom). To provide insight into the various objectives and uses of aggregated outcome data. A qualitative review was performed and the findings were analysed. Benchmarking is a strategy for finding best practices and for improving efficacy and it belongs to the domain of quality management. Benchmarking involves comparing outcome data by means of instrumentation and is relatively tolerant with regard to the validity of the data. Although benchmarking is a function of rom, it must be differentiated form other functions from rom. Clinical management, public accountability, research, payment for performance and information for patients are all functions of rom which require different ways of data feedback and which make different demands on the validity of the underlying data. Benchmarking is often wrongly regarded as being simply a synonym for 'comparing institutions'. It is, however, a method which includes many more factors; it can be used to improve quality and has a more flexible approach to the validity of outcome data and is less concerned than other rom functions about funding and the amount of information given to patients. Benchmarking can make good use of currently available outcome data.

Benchmarking: a method for continuous quality improvement in health.

PubMed

Ettorchi-Tardy, Amina; Levif, Marie; Michel, Philippe

2012-05-01

Benchmarking, a management approach for implementing best practices at best cost, is a recent concept in the healthcare system. The objectives of this paper are to better understand the concept and its evolution in the healthcare sector, to propose an operational definition, and to describe some French and international experiences of benchmarking in the healthcare sector. To this end, we reviewed the literature on this approach's emergence in the industrial sector, its evolution, its fields of application and examples of how it has been used in the healthcare sector. Benchmarking is often thought to consist simply of comparing indicators and is not perceived in its entirety, that is, as a tool based on voluntary and active collaboration among several organizations to create a spirit of competition and to apply best practices. The key feature of benchmarking is its integration within a comprehensive and participatory policy of continuous quality improvement (CQI). Conditions for successful benchmarking focus essentially on careful preparation of the process, monitoring of the relevant indicators, staff involvement and inter-organizational visits. Compared to methods previously implemented in France (CQI and collaborative projects), benchmarking has specific features that set it apart as a healthcare innovation. This is especially true for healthcare or medical-social organizations, as the principle of inter-organizational visiting is not part of their culture. Thus, this approach will need to be assessed for feasibility and acceptability before it is more widely promoted.

Benchmarking of venous thromboembolism prophylaxis practice with ENT.UK guidelines.

PubMed

Al-Qahtani, Ali S

2017-05-01

The aim of this study was to benchmark our guidelines of prevention of venous thromboembolism (VTE) in ENT surgical population against ENT.UK guidelines, and also to encourage healthcare providers to utilize benchmarking as an effective method of improving performance. The study design is prospective descriptive analysis. The setting of this study is tertiary referral centre (Assir Central Hospital, Abha, Saudi Arabia). In this study, we are benchmarking our practice guidelines of the prevention of VTE in the ENT surgical population against that of ENT.UK guidelines to mitigate any gaps. ENT guidelines 2010 were downloaded from the ENT.UK Website. Our guidelines were compared with the possibilities that either our performance meets or fall short of ENT.UK guidelines. Immediate corrective actions will take place if there is quality chasm between the two guidelines. ENT.UK guidelines are evidence-based and updated which may serve as role-model for adoption and benchmarking. Our guidelines were accordingly amended to contain all factors required in providing a quality service to ENT surgical patients. While not given appropriate attention, benchmarking is a useful tool in improving quality of health care. It allows learning from others' practices and experiences, and works towards closing any quality gaps. In addition, benchmarking clinical outcomes is critical for quality improvement and informing decisions concerning service provision. It is recommended to be included on the list of quality improvement methods of healthcare services.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnis Judzis

2003-01-01

This document details the progress to date on the ''OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING'' contract for the quarter starting October 2002 through December 2002. Even though we are awaiting the optimization portion of the testing program, accomplishments included the following: (1) Smith International participated in the DOE Mud Hammer program through full scale benchmarking testing during the week of 4 November 2003. (2) TerraTek acknowledges Smith International, BP America, PDVSA, and ConocoPhillips for cost-sharing the Smith benchmarking tests allowing extension of the contract to add to themore » benchmarking testing program. (3) Following the benchmark testing of the Smith International hammer, representatives from DOE/NETL, TerraTek, Smith International and PDVSA met at TerraTek in Salt Lake City to review observations, performance and views on the optimization step for 2003. (4) The December 2002 issue of Journal of Petroleum Technology (Society of Petroleum Engineers) highlighted the DOE fluid hammer testing program and reviewed last years paper on the benchmark performance of the SDS Digger and Novatek hammers. (5) TerraTek's Sid Green presented a technical review for DOE/NETL personnel in Morgantown on ''Impact Rock Breakage'' and its importance on improving fluid hammer performance. Much discussion has taken place on the issues surrounding mud hammer performance at depth conditions.« less

A Preliminary Investigation of Caffeinated Alcohol Use During Spring Break.

PubMed

Linden-Carmichael, Ashley N; Lau-Barraco, Cathy

2016-06-06

Caffeinated alcoholic beverages (e.g., Red Bull and vodka) are popular but associated with negative consequences. CABs may be particularly popular during Spring Break, a potentially risky social event. We aimed to identify the prevalence of Spring Break caffeinated alcohol use, determine how caffeinated alcohol use Spring Break drinking habits differ from usual, and examine the association between Spring Break caffeinated alcohol use and alcohol-related problems. Data were collected from 95 college students during March of 2013 and 2014. Students completed questionnaires of their alcohol and caffeinated alcohol use before and during Spring Break and Spring Break alcohol-related problems. Approximately 54% of students used caffeinated alcohol during Spring Break. Spring Break caffeinated alcohol use was associated with more alcohol-related problems, even after controlling for other alcohol consumed and Spring Break vacation status. Caffeinated alcoholic beverages are commonly consumed during Spring Break and their use uniquely predicted harms. Prevention efforts placed on caffeinated alcoholic beverage users may be helpful in reducing Spring Break-related harms.

An Alignment of the Canadian Language Benchmarks to the BC ESL Articulation Levels. Final Report - January 2007

ERIC Educational Resources Information Center

Barbour, Ross; Ostler, Catherine; Templeman, Elizabeth; West, Elizabeth

2007-01-01

The British Columbia (BC) English as a Second Language (ESL) Articulation Committee's Canadian Language Benchmarks project was precipitated by ESL instructors' desire to address transfer difficulties of ESL students within the BC transfer system and to respond to the recognition that the Canadian Language Benchmarks, a descriptive scale of ESL…

Within-Group Effect-Size Benchmarks for Problem-Solving Therapy for Depression in Adults

ERIC Educational Resources Information Center

Rubin, Allen; Yu, Miao

2017-01-01

This article provides benchmark data on within-group effect sizes from published randomized clinical trials that supported the efficacy of problem-solving therapy (PST) for depression among adults. Benchmarks are broken down by type of depression (major or minor), type of outcome measure (interview or self-report scale), whether PST was provided…

Benchmarking can add up for healthcare accounting.

PubMed

Czarnecki, M T

1994-09-01

In 1993, a healthcare accounting and finance benchmarking survey of hospital and nonhospital organizations gathered statistics about key common performance areas. A low response did not allow for statistically significant findings, but the survey identified performance measures that can be used in healthcare financial management settings. This article explains the benchmarking process and examines some of the 1993 study's findings.

Learning from Follow Up Surveys of Graduates: The Austin Teacher Program and the Benchmark Project. A Discussion Paper.

ERIC Educational Resources Information Center

Baker, Thomas E.

This paper describes Austin College's (Texas) participation in the Benchmark Project, a collaborative followup study of teacher education graduates and their principals, focusing on the second round of data collection. The Benchmark Project was a collaboration of 11 teacher preparation programs that gathered and analyzed data comparing graduates…

75 FR 28643 - Pine Island, Matlacha Pass, Island Bay, and Caloosahatchee National Wildlife Refuges, Lee and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-21

... would work with the partners to establish benchmarks to record sea level rise and beach profiles and... partners to establish benchmarks to record sea level rise and beach profiles and shoreline changes, which... establish benchmarks to record sea level rise and beach profiles and shoreline changes, which could...

Using Participatory Action Research to Study the Implementation of Career Development Benchmarks at a New Zealand University

ERIC Educational Resources Information Center

Furbish, Dale S.; Bailey, Robyn; Trought, David

2016-01-01

Benchmarks for career development services at tertiary institutions have been developed by Careers New Zealand. The benchmarks are intended to provide standards derived from international best practices to guide career development services. A new career development service was initiated at a large New Zealand university just after the benchmarks…

Utilizing Benchmarking to Study the Effectiveness of Parent-Child Interaction Therapy Implemented in a Community Setting

ERIC Educational Resources Information Center

Self-Brown, Shannon; Valente, Jessica R.; Wild, Robert C.; Whitaker, Daniel J.; Galanter, Rachel; Dorsey, Shannon; Stanley, Jenelle

2012-01-01

Benchmarking is a program evaluation approach that can be used to study whether the outcomes of parents/children who participate in an evidence-based program in the community approximate the outcomes found in randomized trials. This paper presents a case illustration using benchmarking methodology to examine a community implementation of…

77 FR 75978 - Utility Scale Wind Towers From the People's Republic of China: Final Affirmative Countervailing...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... Comment 19: Value Added Tax and Import Duties in the HRS Benchmark Used to Calculate CS Wind's Benefit...: Preliminary Determination of Sales at Less Than Fair Value and Postponement of Final Determination, 77 FR... of HRS Benchmark Provision of Electricity for LTAR Comment 16: Electricity Benchmarks Tax Programs...

Work Readiness Standards and Benchmarks: The Key to Differentiating America's Workforce and Regaining Global Competitiveness

ERIC Educational Resources Information Center

Clark, Hope

2013-01-01

In this report, ACT presents a definition of "work readiness" along with empirically driven ACT Work Readiness Standards and Benchmarks. The introduction of standards and benchmarks for workplace success provides a more complete picture of the factors that are important in establishing readiness for success throughout a lifetime. While…

77 FR 67707 - Self-Regulatory Organizations; NYSE Arca, Inc.; Order Granting Approval of Proposed Rule Change...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-13

... and expenses) that correlate positively to three times (300%) the daily return of a target benchmark, meaning a Leveraged Bull Fund will attempt to move in the same direction as the target benchmark. The... inverse (opposite) of three times the return of a target benchmark, meaning that the Leveraged Bear Funds...

40 CFR 141.540 - Who has to develop a disinfection benchmark?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Who has to develop a disinfection... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.540 Who has to develop a disinfection benchmark? If you are a subpart H system required to develop a disinfection profile under §§ 141...

40 CFR 141.540 - Who has to develop a disinfection benchmark?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Who has to develop a disinfection... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.540 Who has to develop a disinfection benchmark? If you are a subpart H system required to develop a disinfection profile under §§ 141...

40 CFR 141.540 - Who has to develop a disinfection benchmark?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Who has to develop a disinfection... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.540 Who has to develop a disinfection benchmark? If you are a subpart H system required to develop a disinfection profile under §§ 141...

A Consumer's Guide to Benchmark Dose Models: Results of U.S. EPA Testing of 14 Dichotomous, 8 Continuous, and 6 Developmental Models (Presentation)

EPA Science Inventory

Benchmark dose risk assessment software (BMDS) was designed by EPA to generate dose-response curves and facilitate the analysis, interpretation and synthesis of toxicological data. Partial results of QA/QC testing of the EPA benchmark dose software (BMDS) are presented. BMDS pr...

Teachers' Perceptions of the Effectiveness of Benchmark Assessment Data to Predict Student Math Grades

ERIC Educational Resources Information Center

Lewis, Lawanna M.

2010-01-01

The purpose of this correlational quantitative study was to examine the extent to which teachers perceive the use of benchmark assessment data as effective; the extent to which the time spent teaching mathematics is associated with students' mathematics grades, and the extent to which the results of math benchmark assessment influence teachers'…

Implementing Cognitive Strategy Instruction across the School: The Benchmark Manual for Teachers.

ERIC Educational Resources Information Center

Gaskins, Irene; Elliot, Thorne

Improving reading instruction has been the primary focus at the Benchmark School in Media, Pennsylvania. This book describes the various phases of Benchmark's development of a program to create strategic learners, thinkers, and problem solvers across the curriculum. The goal is to provide teachers and administrators with a handbook that can be…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, J; Dossa, D; Gokhale, M

Critical data science applications requiring frequent access to storage perform poorly on today's computing architectures. This project addresses efficient computation of data-intensive problems in national security and basic science by exploring, advancing, and applying a new form of computing called storage-intensive supercomputing (SISC). Our goal is to enable applications that simply cannot run on current systems, and, for a broad range of data-intensive problems, to deliver an order of magnitude improvement in price/performance over today's data-intensive architectures. This technical report documents much of the work done under LDRD 07-ERD-063 Storage Intensive Supercomputing during the period 05/07-09/07. The following chapters describe:more » (1) a new file I/O monitoring tool iotrace developed to capture the dynamic I/O profiles of Linux processes; (2) an out-of-core graph benchmark for level-set expansion of scale-free graphs; (3) an entity extraction benchmark consisting of a pipeline of eight components; and (4) an image resampling benchmark drawn from the SWarp program in the LSST data processing pipeline. The performance of the graph and entity extraction benchmarks was measured in three different scenarios: data sets residing on the NFS file server and accessed over the network; data sets stored on local disk; and data sets stored on the Fusion I/O parallel NAND Flash array. The image resampling benchmark compared performance of software-only to GPU-accelerated. In addition to the work reported here, an additional text processing application was developed that used an FPGA to accelerate n-gram profiling for language classification. The n-gram application will be presented at SC07 at the High Performance Reconfigurable Computing Technologies and Applications Workshop. The graph and entity extraction benchmarks were run on a Supermicro server housing the NAND Flash 40GB parallel disk array, the Fusion-io. The Fusion system specs are as follows: SuperMicro X7DBE Xeon Dual Socket Blackford Server Motherboard; 2 Intel Xeon Dual-Core 2.66 GHz processors; 1 GB DDR2 PC2-5300 RAM (2 x 512); 80GB Hard Drive (Seagate SATA II Barracuda). The Fusion board is presently capable of 4X in a PCIe slot. The image resampling benchmark was run on a dual Xeon workstation with NVIDIA graphics card (see Chapter 5 for full specification). An XtremeData Opteron+FPGA was used for the language classification application. We observed that these benchmarks are not uniformly I/O intensive. The only benchmark that showed greater that 50% of the time in I/O was the graph algorithm when it accessed data files over NFS. When local disk was used, the graph benchmark spent at most 40% of its time in I/O. The other benchmarks were CPU dominated. The image resampling benchmark and language classification showed order of magnitude speedup over software by using co-processor technology to offload the CPU-intensive kernels. Our experiments to date suggest that emerging hardware technologies offer significant benefit to boosting the performance of data-intensive algorithms. Using GPU and FPGA co-processors, we were able to improve performance by more than an order of magnitude on the benchmark algorithms, eliminating the processor bottleneck of CPU-bound tasks. Experiments with a prototype solid state nonvolative memory available today show 10X better throughput on random reads than disk, with a 2X speedup on a graph processing benchmark when compared to the use of local SATA disk.« less

Benchmarking is associated with improved quality of care in type 2 diabetes: the OPTIMISE randomized, controlled trial.

PubMed

Hermans, Michel P; Elisaf, Moses; Michel, Georges; Muls, Erik; Nobels, Frank; Vandenberghe, Hans; Brotons, Carlos

2013-11-01

To assess prospectively the effect of benchmarking on quality of primary care for patients with type 2 diabetes by using three major modifiable cardiovascular risk factors as critical quality indicators. Primary care physicians treating patients with type 2 diabetes in six European countries were randomized to give standard care (control group) or standard care with feedback benchmarked against other centers in each country (benchmarking group). In both groups, laboratory tests were performed every 4 months. The primary end point was the percentage of patients achieving preset targets of the critical quality indicators HbA1c, LDL cholesterol, and systolic blood pressure (SBP) after 12 months of follow-up. Of 4,027 patients enrolled, 3,996 patients were evaluable and 3,487 completed 12 months of follow-up. Primary end point of HbA1c target was achieved in the benchmarking group by 58.9 vs. 62.1% in the control group (P = 0.398) after 12 months; 40.0 vs. 30.1% patients met the SBP target (P < 0.001); 54.3 vs. 49.7% met the LDL cholesterol target (P = 0.006). Percentages of patients meeting all three targets increased during the study in both groups, with a statistically significant increase observed in the benchmarking group. The percentage of patients achieving all three targets at month 12 was significantly larger in the benchmarking group than in the control group (12.5 vs. 8.1%; P < 0.001). In this prospective, randomized, controlled study, benchmarking was shown to be an effective tool for increasing achievement of critical quality indicators and potentially reducing patient cardiovascular residual risk profile.

Benchmarking Is Associated With Improved Quality of Care in Type 2 Diabetes

PubMed Central

Hermans, Michel P.; Elisaf, Moses; Michel, Georges; Muls, Erik; Nobels, Frank; Vandenberghe, Hans; Brotons, Carlos

2013-01-01

OBJECTIVE To assess prospectively the effect of benchmarking on quality of primary care for patients with type 2 diabetes by using three major modifiable cardiovascular risk factors as critical quality indicators. RESEARCH DESIGN AND METHODS Primary care physicians treating patients with type 2 diabetes in six European countries were randomized to give standard care (control group) or standard care with feedback benchmarked against other centers in each country (benchmarking group). In both groups, laboratory tests were performed every 4 months. The primary end point was the percentage of patients achieving preset targets of the critical quality indicators HbA1c, LDL cholesterol, and systolic blood pressure (SBP) after 12 months of follow-up. RESULTS Of 4,027 patients enrolled, 3,996 patients were evaluable and 3,487 completed 12 months of follow-up. Primary end point of HbA1c target was achieved in the benchmarking group by 58.9 vs. 62.1% in the control group (P = 0.398) after 12 months; 40.0 vs. 30.1% patients met the SBP target (P < 0.001); 54.3 vs. 49.7% met the LDL cholesterol target (P = 0.006). Percentages of patients meeting all three targets increased during the study in both groups, with a statistically significant increase observed in the benchmarking group. The percentage of patients achieving all three targets at month 12 was significantly larger in the benchmarking group than in the control group (12.5 vs. 8.1%; P < 0.001). CONCLUSIONS In this prospective, randomized, controlled study, benchmarking was shown to be an effective tool for increasing achievement of critical quality indicators and potentially reducing patient cardiovascular residual risk profile. PMID:23846810

A benchmark study of the sea-level equation in GIA modelling

NASA Astrophysics Data System (ADS)

Martinec, Zdenek; Klemann, Volker; van der Wal, Wouter; Riva, Riccardo; Spada, Giorgio; Simon, Karen; Blank, Bas; Sun, Yu; Melini, Daniele; James, Tom; Bradley, Sarah

2017-04-01

The sea-level load in glacial isostatic adjustment (GIA) is described by the so called sea-level equation (SLE), which represents the mass redistribution between ice sheets and oceans on a deforming earth. Various levels of complexity of SLE have been proposed in the past, ranging from a simple mean global sea level (the so-called eustatic sea level) to the load with a deforming ocean bottom, migrating coastlines and a changing shape of the geoid. Several approaches to solve the SLE have been derived, from purely analytical formulations to fully numerical methods. Despite various teams independently investigating GIA, there has been no systematic intercomparison amongst the solvers through which the methods may be validated. The goal of this paper is to present a series of benchmark experiments designed for testing and comparing numerical implementations of the SLE. Our approach starts with simple load cases even though the benchmark will not result in GIA predictions for a realistic loading scenario. In the longer term we aim for a benchmark with a realistic loading scenario, and also for benchmark solutions with rotational feedback. The current benchmark uses an earth model for which Love numbers have been computed and benchmarked in Spada et al (2011). In spite of the significant differences in the numerical methods employed, the test computations performed so far show a satisfactory agreement between the results provided by the participants. The differences found can often be attributed to the different approximations inherent to the various algorithms. Literature G. Spada, V. R. Barletta, V. Klemann, R. E. M. Riva, Z. Martinec, P. Gasperini, B. Lund, D. Wolf, L. L. A. Vermeersen, and M. A. King, 2011. A benchmark study for glacial isostatic adjustment codes. Geophys. J. Int. 185: 106-132 doi:10.1111/j.1365-

Toward benchmarking in catalysis science: Best practices, challenges, and opportunities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bligaard, Thomas; Bullock, R. Morris; Campbell, Charles T.

Benchmarking is a community-based and (preferably) community-driven activity involving consensus-based decisions on how to make reproducible, fair, and relevant assessments. In catalysis science, important catalyst performance metrics include activity, selectivity, and the deactivation profile, which enable comparisons between new and standard catalysts. Benchmarking also requires careful documentation, archiving, and sharing of methods and measurements, to ensure that the full value of research data can be realized. Beyond these goals, benchmarking presents unique opportunities to advance and accelerate understanding of complex reaction systems by combining and comparing experimental information from multiple, in situ and operando techniques with theoretical insights derived frommore » calculations characterizing model systems. This Perspective describes the origins and uses of benchmarking and its applications in computational catalysis, heterogeneous catalysis, molecular catalysis, and electrocatalysis. As a result, it also discusses opportunities and challenges for future developments in these fields.« less

Thermo-hydro-mechanical-chemical processes in fractured-porous media: Benchmarks and examples

NASA Astrophysics Data System (ADS)

Kolditz, O.; Shao, H.; Görke, U.; Kalbacher, T.; Bauer, S.; McDermott, C. I.; Wang, W.

2012-12-01

The book comprises an assembly of benchmarks and examples for porous media mechanics collected over the last twenty years. Analysis of thermo-hydro-mechanical-chemical (THMC) processes is essential to many applications in environmental engineering, such as geological waste deposition, geothermal energy utilisation, carbon capture and storage, water resources management, hydrology, even climate change. In order to assess the feasibility as well as the safety of geotechnical applications, process-based modelling is the only tool to put numbers, i.e. to quantify future scenarios. This charges a huge responsibility concerning the reliability of computational tools. Benchmarking is an appropriate methodology to verify the quality of modelling tools based on best practices. Moreover, benchmarking and code comparison foster community efforts. The benchmark book is part of the OpenGeoSys initiative - an open source project to share knowledge and experience in environmental analysis and scientific computation.

Toward benchmarking in catalysis science: Best practices, challenges, and opportunities

DOE PAGES

Bligaard, Thomas; Bullock, R. Morris; Campbell, Charles T.; ...

2016-03-07

Benchmarking is a community-based and (preferably) community-driven activity involving consensus-based decisions on how to make reproducible, fair, and relevant assessments. In catalysis science, important catalyst performance metrics include activity, selectivity, and the deactivation profile, which enable comparisons between new and standard catalysts. Benchmarking also requires careful documentation, archiving, and sharing of methods and measurements, to ensure that the full value of research data can be realized. Beyond these goals, benchmarking presents unique opportunities to advance and accelerate understanding of complex reaction systems by combining and comparing experimental information from multiple, in situ and operando techniques with theoretical insights derived frommore » calculations characterizing model systems. This Perspective describes the origins and uses of benchmarking and its applications in computational catalysis, heterogeneous catalysis, molecular catalysis, and electrocatalysis. As a result, it also discusses opportunities and challenges for future developments in these fields.« less

15 CFR 801.11 - Rules and regulations for the BE-140, Benchmark Survey of Insurance Transactions by U.S...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons. 801.11 Section... Transactions by U.S. Insurance Companies with Foreign Persons. (a) The BE-140, Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons, will be conducted covering calendar year 2008...

15 CFR 801.11 - Rules and regulations for the BE-140, Benchmark Survey of Insurance Transactions by U.S...

Code of Federal Regulations, 2012 CFR

2012-01-01

..., Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons. 801.11 Section... Transactions by U.S. Insurance Companies with Foreign Persons. (a) The BE-140, Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons, will be conducted covering calendar year 2008...

27 CFR 9.171 - San Bernabe.

Code of Federal Regulations, 2011 CFR

2011-04-01

... benchmark 304, located one-half mile southwest of King City, along the Salinas River, in Township 20 South (T20S) and Range 8 East (R8E). Proceed southeast in a straight line for 2.35 miles to benchmark 304, at... miles to benchmark 336, between U.S. Highway 101 and the Salinas River, in T20S and R8E (San Lucas...

27 CFR 9.171 - San Bernabe.

Code of Federal Regulations, 2010 CFR

2010-04-01

... benchmark 304, located one-half mile southwest of King City, along the Salinas River, in Township 20 South (T20S) and Range 8 East (R8E). Proceed southeast in a straight line for 2.35 miles to benchmark 304, at... miles to benchmark 336, between U.S. Highway 101 and the Salinas River, in T20S and R8E (San Lucas...

27 CFR 9.171 - San Bernabe.

Code of Federal Regulations, 2013 CFR

2013-04-01

... benchmark 304, located one-half mile southwest of King City, along the Salinas River, in Township 20 South (T20S) and Range 8 East (R8E). Proceed southeast in a straight line for 2.35 miles to benchmark 304, at... miles to benchmark 336, between U.S. Highway 101 and the Salinas River, in T20S and R8E (San Lucas...

27 CFR 9.171 - San Bernabe.

Code of Federal Regulations, 2014 CFR

2014-04-01

... benchmark 304, located one-half mile southwest of King City, along the Salinas River, in Township 20 South (T20S) and Range 8 East (R8E). Proceed southeast in a straight line for 2.35 miles to benchmark 304, at... miles to benchmark 336, between U.S. Highway 101 and the Salinas River, in T20S and R8E (San Lucas...

27 CFR 9.171 - San Bernabe.

Code of Federal Regulations, 2012 CFR

2012-04-01

... benchmark 304, located one-half mile southwest of King City, along the Salinas River, in Township 20 South (T20S) and Range 8 East (R8E). Proceed southeast in a straight line for 2.35 miles to benchmark 304, at... miles to benchmark 336, between U.S. Highway 101 and the Salinas River, in T20S and R8E (San Lucas...

Benchmarking. Issues in the Design and Implementation of a Benchmarking System for Employment and Training Programs for Young People.

ERIC Educational Resources Information Center

Coughlin, David C.; Bielen, Rhonda P.

This paper has been prepared to assist the United States Department of Labor to explore new approaches to evaluating and measuring the performance of employment and training activities for youth. As one of several tools for evaluating success of local youth training programs, "benchmarking" provides a system for measuring the development…

Piloting a Process Maturity Model as an e-Learning Benchmarking Method

ERIC Educational Resources Information Center

Petch, Jim; Calverley, Gayle; Dexter, Hilary; Cappelli, Tim

2007-01-01

As part of a national e-learning benchmarking initiative of the UK Higher Education Academy, the University of Manchester is carrying out a pilot study of a method to benchmark e-learning in an institution. The pilot was designed to evaluate the operational viability of a method based on the e-Learning Maturity Model developed at the University of…

CLEAR: Cross-Layer Exploration for Architecting Resilience

DTIC Science & Technology

2017-03-01

benchmark analysis, also provides cost-effective solutions (~1% additional energy cost for the same 50× improvement). This paper addresses the...core (OoO-core) [Wang 04], across 18 benchmarks . Such extensive exploration enables us to conclusively answer the above cross-layer resilience...analysis of the effects of soft errors on application benchmarks , provides a highly effective soft error resilience approach. 3. The above

Benchmarking in health care: using the Internet to identify resources.

PubMed

Lingle, V A

1996-01-01

Benchmarking is a quality improvement tool that is increasingly being applied to the health care field and to the libraries within that field. Using mostly resources assessible at no charge through the Internet, a collection of information was compiled on benchmarking and its applications. Sources could be identified in several formats including books, journals and articles, multi-media materials, and organizations.

Teaching Benchmark Strategy for Fifth-Graders in Taiwan

ERIC Educational Resources Information Center

Yang, Der-Ching; Lai, M. L.

2013-01-01

The key purpose of this study was how we taught the use of benchmark strategy when comparing fraction for fifth-graders in Taiwan. 26 fifth graders from a public elementary in south Taiwan were selected to join this study. Results of this case study showed that students had a much progress on the use of benchmark strategy when comparing fraction…

15 CFR 801.12 - Rules and regulations for the BE-140, Benchmark Survey of Insurance Transactions by U.S...

Code of Federal Regulations, 2010 CFR

2010-01-01

... insurance company. Part 3 requests information needed to determine whether a report is required, the types..., Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons. 801.12 Section... Transactions by U.S. Insurance Companies with Foreign Persons. (a) The BE-140, Benchmark Survey of Insurance...

Ensuring Academic Depth and Rigour in Teacher Education through Benchmarking, with Special Attention to Context

ERIC Educational Resources Information Center

Steyn, H. J.; van der Walt, J. L.; Wolhuter, C. C.

2016-01-01

Benchmarking is one way of ensuring academic depth and rigour in teacher education. After making a case for setting benchmarks in teacher education based on the widely recognised intra-education system contextual factors, the importance of also taking into account the external (e.g. the national-social) context in which teacher education occurs is…

Journal Benchmarking for Strategic Publication Management and for Improving Journal Positioning in the World Ranking Systems

ERIC Educational Resources Information Center

Moskovkin, Vladimir M.; Bocharova, Emilia A.; Balashova, Oksana V.

2014-01-01

Purpose: The purpose of this paper is to introduce and develop the methodology of journal benchmarking. Design/Methodology/ Approach: The journal benchmarking method is understood to be an analytic procedure of continuous monitoring and comparing of the advance of specific journal(s) against that of competing journals in the same subject area,…

Higher Education Ranking and Leagues Tables: Lessons Learned from Benchmarking

ERIC Educational Resources Information Center

Proulx, Roland

2007-01-01

The paper intends to contribute to the debate on ranking and league tables by adopting a critical approach to ranking methodologies from the point of view of a university benchmarking exercise. The absence of a strict benchmarking exercise in the ranking process has been, in the opinion of the author, one of the major problems encountered in the…

77 FR 58881 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing of Proposed Rule Change Relating...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-24

... return (before fees and expenses) of its target benchmark commodity or currency on a given day. The...% of the return (before fees and expenses) of its target benchmark commodity on a given day. The Bear... correlate positively to three times (300%) the daily return of a target benchmark, meaning a Leveraged Bull...

Student Satisfaction Surveys: The Value in Taking an Historical Perspective

ERIC Educational Resources Information Center

Kane, David; Williams, James; Cappuccini-Ansfield, Gillian

2008-01-01

Benchmarking satisfaction over time can be extremely valuable where a consistent feedback cycle is employed. However, the value of benchmarking over a long period of time has not been analysed in depth. What is the value of benchmarking this type of data over time? What does it tell us about a feedback and action cycle? What impact does a study of…

HPGMG 1.0: A Benchmark for Ranking High Performance Computing Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, Mark; Brown, Jed; Shalf, John

2014-05-05

This document provides an overview of the benchmark ? HPGMG ? for ranking large scale general purpose computers for use on the Top500 list [8]. We provide a rationale for the need for a replacement for the current metric HPL, some background of the Top500 list and the challenges of developing such a metric; we discuss our design philosophy and methodology, and an overview of the specification of the benchmark. The primary documentation with maintained details on the specification can be found at hpgmg.org and the Wiki and benchmark code itself can be found in the repository https://bitbucket.org/hpgmg/hpgmg.

Translational benchmark risk analysis

PubMed Central

Piegorsch, Walter W.

2010-01-01

Translational development – in the sense of translating a mature methodology from one area of application to another, evolving area – is discussed for the use of benchmark doses in quantitative risk assessment. Illustrations are presented with traditional applications of the benchmark paradigm in biology and toxicology, and also with risk endpoints that differ from traditional toxicological archetypes. It is seen that the benchmark approach can apply to a diverse spectrum of risk management settings. This suggests a promising future for this important risk-analytic tool. Extensions of the method to a wider variety of applications represent a significant opportunity for enhancing environmental, biomedical, industrial, and socio-economic risk assessments. PMID:20953283

Developing a benchmark for emotional analysis of music

PubMed Central

Yang, Yi-Hsuan; Soleymani, Mohammad

2017-01-01

Music emotion recognition (MER) field rapidly expanded in the last decade. Many new methods and new audio features are developed to improve the performance of MER algorithms. However, it is very difficult to compare the performance of the new methods because of the data representation diversity and scarcity of publicly available data. In this paper, we address these problems by creating a data set and a benchmark for MER. The data set that we release, a MediaEval Database for Emotional Analysis in Music (DEAM), is the largest available data set of dynamic annotations (valence and arousal annotations for 1,802 songs and song excerpts licensed under Creative Commons with 2Hz time resolution). Using DEAM, we organized the ‘Emotion in Music’ task at MediaEval Multimedia Evaluation Campaign from 2013 to 2015. The benchmark attracted, in total, 21 active teams to participate in the challenge. We analyze the results of the benchmark: the winning algorithms and feature-sets. We also describe the design of the benchmark, the evaluation procedures and the data cleaning and transformations that we suggest. The results from the benchmark suggest that the recurrent neural network based approaches combined with large feature-sets work best for dynamic MER. PMID:28282400

Methodology and issues of integral experiments selection for nuclear data validation

NASA Astrophysics Data System (ADS)

Tatiana, Ivanova; Ivanov, Evgeny; Hill, Ian

2017-09-01

Nuclear data validation involves a large suite of Integral Experiments (IEs) for criticality, reactor physics and dosimetry applications. [1] Often benchmarks are taken from international Handbooks. [2, 3] Depending on the application, IEs have different degrees of usefulness in validation, and usually the use of a single benchmark is not advised; indeed, it may lead to erroneous interpretation and results. [1] This work aims at quantifying the importance of benchmarks used in application dependent cross section validation. The approach is based on well-known General Linear Least Squared Method (GLLSM) extended to establish biases and uncertainties for given cross sections (within a given energy interval). The statistical treatment results in a vector of weighting factors for the integral benchmarks. These factors characterize the value added by a benchmark for nuclear data validation for the given application. The methodology is illustrated by one example, selecting benchmarks for 239Pu cross section validation. The studies were performed in the framework of Subgroup 39 (Methods and approaches to provide feedback from nuclear and covariance data adjustment for improvement of nuclear data files) established at the Working Party on International Nuclear Data Evaluation Cooperation (WPEC) of the Nuclear Science Committee under the Nuclear Energy Agency (NEA/OECD).

Decoys Selection in Benchmarking Datasets: Overview and Perspectives

PubMed Central

Réau, Manon; Langenfeld, Florent; Zagury, Jean-François; Lagarde, Nathalie; Montes, Matthieu

2018-01-01

Virtual Screening (VS) is designed to prospectively help identifying potential hits, i.e., compounds capable of interacting with a given target and potentially modulate its activity, out of large compound collections. Among the variety of methodologies, it is crucial to select the protocol that is the most adapted to the query/target system under study and that yields the most reliable output. To this aim, the performance of VS methods is commonly evaluated and compared by computing their ability to retrieve active compounds in benchmarking datasets. The benchmarking datasets contain a subset of known active compounds together with a subset of decoys, i.e., assumed non-active molecules. The composition of both the active and the decoy compounds subsets is critical to limit the biases in the evaluation of the VS methods. In this review, we focus on the selection of decoy compounds that has considerably changed over the years, from randomly selected compounds to highly customized or experimentally validated negative compounds. We first outline the evolution of decoys selection in benchmarking databases as well as current benchmarking databases that tend to minimize the introduction of biases, and secondly, we propose recommendations for the selection and the design of benchmarking datasets. PMID:29416509

The Medical Library Association Benchmarking Network: development and implementation.

PubMed

Dudden, Rosalind Farnam; Corcoran, Kate; Kaplan, Janice; Magouirk, Jeff; Rand, Debra C; Smith, Bernie Todd

2006-04-01

This article explores the development and implementation of the Medical Library Association (MLA) Benchmarking Network from the initial idea and test survey, to the implementation of a national survey in 2002, to the establishment of a continuing program in 2004. Started as a program for hospital libraries, it has expanded to include other nonacademic health sciences libraries. The activities and timelines of MLA's Benchmarking Network task forces and editorial board from 1998 to 2004 are described. The Benchmarking Network task forces successfully developed an extensive questionnaire with parameters of size and measures of library activity and published a report of the data collected by September 2002. The data were available to all MLA members in the form of aggregate tables. Utilization of Web-based technologies proved feasible for data intake and interactive display. A companion article analyzes and presents some of the data. MLA has continued to develop the Benchmarking Network with the completion of a second survey in 2004. The Benchmarking Network has provided many small libraries with comparative data to present to their administrators. It is a challenge for the future to convince all MLA members to participate in this valuable program.

The Medical Library Association Benchmarking Network: development and implementation*

PubMed Central

Dudden, Rosalind Farnam; Corcoran, Kate; Kaplan, Janice; Magouirk, Jeff; Rand, Debra C.; Smith, Bernie Todd

2006-01-01

Objective: This article explores the development and implementation of the Medical Library Association (MLA) Benchmarking Network from the initial idea and test survey, to the implementation of a national survey in 2002, to the establishment of a continuing program in 2004. Started as a program for hospital libraries, it has expanded to include other nonacademic health sciences libraries. Methods: The activities and timelines of MLA's Benchmarking Network task forces and editorial board from 1998 to 2004 are described. Results: The Benchmarking Network task forces successfully developed an extensive questionnaire with parameters of size and measures of library activity and published a report of the data collected by September 2002. The data were available to all MLA members in the form of aggregate tables. Utilization of Web-based technologies proved feasible for data intake and interactive display. A companion article analyzes and presents some of the data. MLA has continued to develop the Benchmarking Network with the completion of a second survey in 2004. Conclusions: The Benchmarking Network has provided many small libraries with comparative data to present to their administrators. It is a challenge for the future to convince all MLA members to participate in this valuable program. PMID:16636702

Space Weather Action Plan Ionizing Radiation Benchmarks: Phase 1 update and plans for Phase 2

NASA Astrophysics Data System (ADS)

Talaat, E. R.; Kozyra, J.; Onsager, T. G.; Posner, A.; Allen, J. E., Jr.; Black, C.; Christian, E. R.; Copeland, K.; Fry, D. J.; Johnston, W. R.; Kanekal, S. G.; Mertens, C. J.; Minow, J. I.; Pierson, J.; Rutledge, R.; Semones, E.; Sibeck, D. G.; St Cyr, O. C.; Xapsos, M.

2017-12-01

Changes in the near-Earth radiation environment can affect satellite operations, astronauts in space, commercial space activities, and the radiation environment on aircraft at relevant latitudes or altitudes. Understanding the diverse effects of increased radiation is challenging, but producing ionizing radiation benchmarks will help address these effects. The following areas have been considered in addressing the near-Earth radiation environment: the Earth's trapped radiation belts, the galactic cosmic ray background, and solar energetic-particle events. The radiation benchmarks attempt to account for any change in the near-Earth radiation environment, which, under extreme cases, could present a significant risk to critical infrastructure operations or human health. The goal of these ionizing radiation benchmarks and associated confidence levels will define at least the radiation intensity as a function of time, particle type, and energy for an occurrence frequency of 1 in 100 years and an intensity level at the theoretical maximum for the event. In this paper, we present the benchmarks that address radiation levels at all applicable altitudes and latitudes in the near-Earth environment, the assumptions made and the associated uncertainties, and the next steps planned for updating the benchmarks.

Comprehensive Benchmark Suite for Simulation of Particle Laden Flows Using the Discrete Element Method with Performance Profiles from the Multiphase Flow with Interface eXchanges (MFiX) Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Peiyuan; Brown, Timothy; Fullmer, William D.

Five benchmark problems are developed and simulated with the computational fluid dynamics and discrete element model code MFiX. The benchmark problems span dilute and dense regimes, consider statistically homogeneous and inhomogeneous (both clusters and bubbles) particle concentrations and a range of particle and fluid dynamic computational loads. Several variations of the benchmark problems are also discussed to extend the computational phase space to cover granular (particles only), bidisperse and heat transfer cases. A weak scaling analysis is performed for each benchmark problem and, in most cases, the scalability of the code appears reasonable up to approx. 103 cores. Profiling ofmore » the benchmark problems indicate that the most substantial computational time is being spent on particle-particle force calculations, drag force calculations and interpolating between discrete particle and continuum fields. Hardware performance analysis was also carried out showing significant Level 2 cache miss ratios and a rather low degree of vectorization. These results are intended to serve as a baseline for future developments to the code as well as a preliminary indicator of where to best focus performance optimizations.« less

Developing a benchmark for emotional analysis of music.

PubMed

Aljanaki, Anna; Yang, Yi-Hsuan; Soleymani, Mohammad

2017-01-01

Music emotion recognition (MER) field rapidly expanded in the last decade. Many new methods and new audio features are developed to improve the performance of MER algorithms. However, it is very difficult to compare the performance of the new methods because of the data representation diversity and scarcity of publicly available data. In this paper, we address these problems by creating a data set and a benchmark for MER. The data set that we release, a MediaEval Database for Emotional Analysis in Music (DEAM), is the largest available data set of dynamic annotations (valence and arousal annotations for 1,802 songs and song excerpts licensed under Creative Commons with 2Hz time resolution). Using DEAM, we organized the 'Emotion in Music' task at MediaEval Multimedia Evaluation Campaign from 2013 to 2015. The benchmark attracted, in total, 21 active teams to participate in the challenge. We analyze the results of the benchmark: the winning algorithms and feature-sets. We also describe the design of the benchmark, the evaluation procedures and the data cleaning and transformations that we suggest. The results from the benchmark suggest that the recurrent neural network based approaches combined with large feature-sets work best for dynamic MER.

Benchmarking the cost efficiency of community care in Australian child and adolescent mental health services: implications for future benchmarking.

PubMed

Furber, Gareth; Brann, Peter; Skene, Clive; Allison, Stephen

2011-06-01

The purpose of this study was to benchmark the cost efficiency of community care across six child and adolescent mental health services (CAMHS) drawn from different Australian states. Organizational, contact and outcome data from the National Mental Health Benchmarking Project (NMHBP) data-sets were used to calculate cost per "treatment hour" and cost per episode for the six participating organizations. We also explored the relationship between intake severity as measured by the Health of the Nations Outcome Scales for Children and Adolescents (HoNOSCA) and cost per episode. The average cost per treatment hour was $223, with cost differences across the six services ranging from a mean of $156 to $273 per treatment hour. The average cost per episode was $3349 (median $1577) and there were significant differences in the CAMHS organizational medians ranging from $388 to $7076 per episode. HoNOSCA scores explained at best 6% of the cost variance per episode. These large cost differences indicate that community CAMHS have the potential to make substantial gains in cost efficiency through collaborative benchmarking. Benchmarking forums need considerable financial and business expertise for detailed comparison of business models for service provision.

A large-scale benchmark of gene prioritization methods.

PubMed

Guala, Dimitri; Sonnhammer, Erik L L

2017-04-21

In order to maximize the use of results from high-throughput experimental studies, e.g. GWAS, for identification and diagnostics of new disease-associated genes, it is important to have properly analyzed and benchmarked gene prioritization tools. While prospective benchmarks are underpowered to provide statistically significant results in their attempt to differentiate the performance of gene prioritization tools, a strategy for retrospective benchmarking has been missing, and new tools usually only provide internal validations. The Gene Ontology(GO) contains genes clustered around annotation terms. This intrinsic property of GO can be utilized in construction of robust benchmarks, objective to the problem domain. We demonstrate how this can be achieved for network-based gene prioritization tools, utilizing the FunCoup network. We use cross-validation and a set of appropriate performance measures to compare state-of-the-art gene prioritization algorithms: three based on network diffusion, NetRank and two implementations of Random Walk with Restart, and MaxLink that utilizes network neighborhood. Our benchmark suite provides a systematic and objective way to compare the multitude of available and future gene prioritization tools, enabling researchers to select the best gene prioritization tool for the task at hand, and helping to guide the development of more accurate methods.

ZPR-6 assembly 7 high {sup 240} PU core : a cylindrical assemby with mixed (PU, U)-oxide fuel and a central high {sup 240} PU zone.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lell, R. M.; Schaefer, R. W.; McKnight, R. D.

Over a period of 30 years more than a hundred Zero Power Reactor (ZPR) critical assemblies were constructed at Argonne National Laboratory. The ZPR facilities, ZPR-3, ZPR-6, ZPR-9 and ZPPR, were all fast critical assembly facilities. The ZPR critical assemblies were constructed to support fast reactor development, but data from some of these assemblies are also well suited to form the basis for criticality safety benchmarks. Of the three classes of ZPR assemblies, engineering mockups, engineering benchmarks and physics benchmarks, the last group tends to be most useful for criticality safety. Because physics benchmarks were designed to test fast reactormore » physics data and methods, they were as simple as possible in geometry and composition. The principal fissile species was {sup 235}U or {sup 239}Pu. Fuel enrichments ranged from 9% to 95%. Often there were only one or two main core diluent materials, such as aluminum, graphite, iron, sodium or stainless steel. The cores were reflected (and insulated from room return effects) by one or two layers of materials such as depleted uranium, lead or stainless steel. Despite their more complex nature, a small number of assemblies from the other two classes would make useful criticality safety benchmarks because they have features related to criticality safety issues, such as reflection by soil-like material. The term 'benchmark' in a ZPR program connotes a particularly simple loading aimed at gaining basic reactor physics insight, as opposed to studying a reactor design. In fact, the ZPR-6/7 Benchmark Assembly (Reference 1) had a very simple core unit cell assembled from plates of depleted uranium, sodium, iron oxide, U3O8, and plutonium. The ZPR-6/7 core cell-average composition is typical of the interior region of liquid-metal fast breeder reactors (LMFBRs) of the era. It was one part of the Demonstration Reactor Benchmark Program,a which provided integral experiments characterizing the important features of demonstration-size LMFBRs. As a benchmark, ZPR-6/7 was devoid of many 'real' reactor features, such as simulated control rods and multiple enrichment zones, in its reference form. Those kinds of features were investigated experimentally in variants of the reference ZPR-6/7 or in other critical assemblies in the Demonstration Reactor Benchmark Program.« less

Organic contaminants, trace and major elements, and nutrients in water and sediment sampled in response to the Deepwater Horizon oil spill

USGS Publications Warehouse

Nowell, Lisa H.; Ludtke, Amy S.; Mueller, David K.; Scott, Jonathon C.

2012-01-01

Beach water and sediment samples were collected along the Gulf of Mexico coast to assess differences in contaminant concentrations before and after landfall of Macondo-1 well oil released into the Gulf of Mexico from the sinking of the British Petroleum Corporation's Deepwater Horizon drilling platform. Samples were collected at 70 coastal sites between May 7 and July 7, 2010, to document baseline, or "pre-landfall" conditions. A subset of 48 sites was resampled during October 4 to 14, 2010, after oil had made landfall on the Gulf of Mexico coast, called the "post-landfall" sampling period, to determine if actionable concentrations of oil were present along shorelines. Few organic contaminants were detected in water; their detection frequencies generally were low and similar in pre-landfall and post-landfall samples. Only one organic contaminant--toluene--had significantly higher concentrations in post-landfall than pre-landfall water samples. No water samples exceeded any human-health benchmarks, and only one post-landfall water sample exceeded an aquatic-life benchmark--the toxic-unit benchmark for polycyclic aromatic hydrocarbons (PAH) mixtures. In sediment, concentrations of 3 parent PAHs and 17 alkylated PAH groups were significantly higher in post-landfall samples than pre-landfall samples. One pre-landfall sample from Texas exceeded the sediment toxic-unit benchmark for PAH mixtures; this site was not sampled during the post-landfall period. Empirical upper screening-value benchmarks for PAHs in sediment were exceeded at 37 percent of post-landfall samples and 22 percent of pre-landfall samples, but there was no significant difference in the proportion of samples exceeding benchmarks between paired pre-landfall and post-landfall samples. Seven sites had the largest concentration differences between post-landfall and pre-landfall samples for 15 alkylated PAHs. Five of these seven sites, located in Louisiana, Mississippi, and Alabama, had diagnostic geochemical evidence of Macondo-1 oil in post-landfall sediments and tarballs. For trace and major elements in water, analytical reporting levels for several elements were high and variable. No human-health benchmarks were exceeded, although these were available for only two elements. Aquatic-life benchmarks for trace elements were exceeded in 47 percent of water samples overall. The elements responsible for the most exceedances in post-landfall samples were boron, copper, and manganese. Benchmark exceedances in water could be substantially underestimated because some samples had reporting levels higher than the applicable benchmarks (such as cobalt, copper, lead and zinc) and some elements (such as boron and vanadium) were analyzed in samples from only one sampling period. For trace elements in whole sediment, empirical upper screening-value benchmarks were exceeded in 57 percent of post-landfall samples and 40 percent of pre-landfall samples, but there was no significant difference in the proportion of samples exceeding benchmarks between paired pre-landfall and post-landfall samples. Benchmark exceedance frequencies could be conservatively high because they are based on measurements of total trace-element concentrations in sediment. In the less than 63-micrometer sediment fraction, one or more trace or major elements were anthropogenically enriched relative to national baseline values for U.S. streams for all sediment samples except one. Sixteen percent of sediment samples exceeded upper screening-value benchmarks for, and were enriched in, one or more of the following elements: barium, vanadium, aluminum, manganese, arsenic, chromium, and cobalt. These samples were evenly divided between the sampling periods. Aquatic-life benchmarks were frequently exceeded along the Gulf of Mexico coast by trace elements in both water and sediment and by PAHs in sediment. For the most part, however, significant differences between pre-landfall and post-landfall samples were limited to concentrations of PAHs in sediment. At five sites along the coast, the higher post-landfall concentrations of PAHs were associated with diagnostic geochemical evidence of Deepwater Horizon Macondo-1 oil.

Break the "wall" and become creative: Enacting embodied metaphors in virtual reality.

PubMed

Wang, Xinyue; Lu, Kelong; Runco, Mark A; Hao, Ning

2018-07-01

This study investigated whether the experience of "breaking the walls", the embodiment of the metaphor "breaking the rules", could enhance creative performance. The virtual reality technology was used to simulate the scenario where participants could "break the walls" while walking in a corridor. Participants were asked to solve the creativity-demanding problems (ie., alternative uses tasks, AUT) in either the "break" condition in which they had to break the walls to move forward in VR, or the "no-break" condition where no barrier walls would appear. Results showed higher AUT originality and AUT fluency in the "break" condition than in the "no-break" condition. Moreover, the effects of "breaking the walls" on AUT originality were fully mediated by cognitive flexibility and persistence. These findings may indicate that enacting metaphors such as "breaking the rules" contribute to creative performance. The enhanced cognitive flexibility and persistence may account for the benefits. Copyright © 2018 Elsevier Inc. All rights reserved.

A benchmark for subduction zone modeling

NASA Astrophysics Data System (ADS)

van Keken, P.; King, S.; Peacock, S.

2003-04-01

Our understanding of subduction zones hinges critically on the ability to discern its thermal structure and dynamics. Computational modeling has become an essential complementary approach to observational and experimental studies. The accurate modeling of subduction zones is challenging due to the unique geometry, complicated rheological description and influence of fluid and melt formation. The complicated physics causes problems for the accurate numerical solution of the governing equations. As a consequence it is essential for the subduction zone community to be able to evaluate the ability and limitations of various modeling approaches. The participants of a workshop on the modeling of subduction zones, held at the University of Michigan at Ann Arbor, MI, USA in 2002, formulated a number of case studies to be developed into a benchmark similar to previous mantle convection benchmarks (Blankenbach et al., 1989; Busse et al., 1991; Van Keken et al., 1997). Our initial benchmark focuses on the dynamics of the mantle wedge and investigates three different rheologies: constant viscosity, diffusion creep, and dislocation creep. In addition we investigate the ability of codes to accurate model dynamic pressure and advection dominated flows. Proceedings of the workshop and the formulation of the benchmark are available at www.geo.lsa.umich.edu/~keken/subduction02.html We strongly encourage interested research groups to participate in this benchmark. At Nice 2003 we will provide an update and first set of benchmark results. Interested researchers are encouraged to contact one of the authors for further details.

Performance of Landslide-HySEA tsunami model for NTHMP benchmarking validation process

NASA Astrophysics Data System (ADS)

Macias, Jorge

2017-04-01

In its FY2009 Strategic Plan, the NTHMP required that all numerical tsunami inundation models be verified as accurate and consistent through a model benchmarking process. This was completed in 2011, but only for seismic tsunami sources and in a limited manner for idealized solid underwater landslides. Recent work by various NTHMP states, however, has shown that landslide tsunami hazard may be dominant along significant parts of the US coastline, as compared to hazards from other tsunamigenic sources. To perform the above-mentioned validation process, a set of candidate benchmarks were proposed. These benchmarks are based on a subset of available laboratory date sets for solid slide experiments and deformable slide experiments, and include both submarine and subaerial slides. A benchmark based on a historic field event (Valdez, AK, 1964) close the list of proposed benchmarks. The Landslide-HySEA model has participated in the workshop that was organized at Texas A&M University - Galveston, on January 9-11, 2017. The aim of this presentation is to show some of the numerical results obtained for Landslide-HySEA in the framework of this benchmarking validation/verification effort. Acknowledgements. This research has been partially supported by the Junta de Andalucía research project TESELA (P11-RNM7069), the Spanish Government Research project SIMURISK (MTM2015-70490-C02-01-R) and Universidad de Málaga, Campus de Excelencia Internacional Andalucía Tech. The GPU computations were performed at the Unit of Numerical Methods (University of Malaga).

Benchmarking: A Method for Continuous Quality Improvement in Health

PubMed Central

Ettorchi-Tardy, Amina; Levif, Marie; Michel, Philippe

2012-01-01

Benchmarking, a management approach for implementing best practices at best cost, is a recent concept in the healthcare system. The objectives of this paper are to better understand the concept and its evolution in the healthcare sector, to propose an operational definition, and to describe some French and international experiences of benchmarking in the healthcare sector. To this end, we reviewed the literature on this approach's emergence in the industrial sector, its evolution, its fields of application and examples of how it has been used in the healthcare sector. Benchmarking is often thought to consist simply of comparing indicators and is not perceived in its entirety, that is, as a tool based on voluntary and active collaboration among several organizations to create a spirit of competition and to apply best practices. The key feature of benchmarking is its integration within a comprehensive and participatory policy of continuous quality improvement (CQI). Conditions for successful benchmarking focus essentially on careful preparation of the process, monitoring of the relevant indicators, staff involvement and inter-organizational visits. Compared to methods previously implemented in France (CQI and collaborative projects), benchmarking has specific features that set it apart as a healthcare innovation. This is especially true for healthcare or medical–social organizations, as the principle of inter-organizational visiting is not part of their culture. Thus, this approach will need to be assessed for feasibility and acceptability before it is more widely promoted. PMID:23634166

Stop and revive? The effectiveness of nap and active rest breaks for reducing driver sleepiness.

PubMed

Watling, Christopher N; Smith, Simon S; Horswill, Mark S

2014-11-01

The purpose of this study was to compare the effects of two commonly utilized sleepiness countermeasures: a nap break and an active rest break. The effects of the countermeasures were evaluated by physiological (EEG), subjective, and driving performance measures. Participants completed 2 h of simulated driving, followed by a 15-min nap break or a 15-min active rest break, then completed the final hour of simulated driving. The nap break reduced EEG and subjective sleepiness. The active rest break did not reduce EEG sleepiness, with sleepiness levels eventually increasing, and resulted in an immediate reduction of subjective sleepiness. No difference was found between the two breaks for the driving performance measure. The immediate reduction of subjective sleepiness after the active rest break could leave drivers with erroneous perceptions of their sleepiness, particularly with increases of physiological sleepiness after the break. Copyright © 2014 Society for Psychophysiological Research.

Theoretical uncertainties in the calculation of supersymmetric dark matter observables

NASA Astrophysics Data System (ADS)

Bergeron, Paul; Sandick, Pearl; Sinha, Kuver

2018-05-01

We estimate the current theoretical uncertainty in supersymmetric dark matter predictions by comparing several state-of-the-art calculations within the minimal supersymmetric standard model (MSSM). We consider standard neutralino dark matter scenarios — coannihilation, well-tempering, pseudoscalar resonance — and benchmark models both in the pMSSM framework and in frameworks with Grand Unified Theory (GUT)-scale unification of supersymmetric mass parameters. The pipelines we consider are constructed from the publicly available software packages SOFTSUSY, SPheno, FeynHiggs, SusyHD, micrOMEGAs, and DarkSUSY. We find that the theoretical uncertainty in the relic density as calculated by different pipelines, in general, far exceeds the statistical errors reported by the Planck collaboration. In GUT models, in particular, the relative discrepancies in the results reported by different pipelines can be as much as a few orders of magnitude. We find that these discrepancies are especially pronounced for cases where the dark matter physics relies critically on calculations related to electroweak symmetry breaking, which we investigate in detail, and for coannihilation models, where there is heightened sensitivity to the sparticle spectrum. The dark matter annihilation cross section today and the scattering cross section with nuclei also suffer appreciable theoretical uncertainties, which, as experiments reach the relevant sensitivities, could lead to uncertainty in conclusions regarding the viability or exclusion of particular models.

Striving for Better Medical Education: the Simulation Approach.

PubMed

Sakakushev, Boris E; Marinov, Blagoi I; Stefanova, Penka P; Kostianev, Stefan St; Georgiou, Evangelos K

2017-06-01

Medical simulation is a rapidly expanding area within medical education due to advances in technology, significant reduction in training hours and increased procedural complexity. Simulation training aims to enhance patient safety through improved technical competency and eliminating human factors in a risk free environment. It is particularly applicable to a practical, procedure-orientated specialties. Simulation can be useful for novice trainees, experienced clinicians (e.g. for revalidation) and team building. It has become a cornerstone in the delivery of medical education, being a paradigm shift in how doctors are educated and trained. Simulation must take a proactive position in the development of metric-based simulation curriculum, adoption of proficiency benchmarking definitions, and should not depend on the simulation platforms used. Conversely, ingraining of poor practice may occur in the absence of adequate supervision, and equipment malfunction during the simulation can break the immersion and disrupt any learning that has occurred. Despite the presence of high technology, there is a substantial learning curve for both learners and facilitators. The technology of simulation continues to advance, offering devices capable of improved fidelity in virtual reality simulation, more sophisticated procedural practice and advanced patient simulators. Simulation-based training has also brought about paradigm shifts in the medical and surgical education arenas and ensured that the scope and impact of simulation will continue to broaden.

High-precision branching ratio measurement for the superallowed β+ emitter Ga62

NASA Astrophysics Data System (ADS)

Finlay, P.; Ball, G. C.; Leslie, J. R.; Svensson, C. E.; Towner, I. S.; Austin, R. A. E.; Bandyopadhyay, D.; Chaffey, A.; Chakrawarthy, R. S.; Garrett, P. E.; Grinyer, G. F.; Hackman, G.; Hyland, B.; Kanungo, R.; Leach, K. G.; Mattoon, C. M.; Morton, A. C.; Pearson, C. J.; Phillips, A. A.; Ressler, J. J.; Sarazin, F.; Savajols, H.; Schumaker, M. A.; Wong, J.

2008-08-01

A high-precision branching ratio measurement for the superallowed β+ decay of Ga62 was performed at the Isotope Separator and Accelerator (ISAC) radioactive ion beam facility. The 8π spectrometer, an array of 20 high-purity germanium detectors, was employed to detect the γ rays emitted following Gamow-Teller and nonanalog Fermi β+ decays of Ga62, and the SCEPTAR plastic scintillator array was used to detect the emitted β particles. Thirty γ rays were identified following Ga62 decay, establishing the superallowed branching ratio to be 99.858(8)%. Combined with the world-average half-life and a recent high-precision Q-value measurement for Ga62, this branching ratio yields an ft value of 3074.3±1.1 s, making Ga62 among the most precisely determined superallowed ft values. Comparison between the superallowed ft value determined in this work and the world-average corrected F tmacr value allows the large nuclear-structure-dependent correction for Ga62 decay to be experimentally determined from the CVC hypothesis to better than 7% of its own value, the most precise experimental determination for any superallowed emitter. These results provide a benchmark for the refinement of the theoretical description of isospin-symmetry breaking in A⩾62 superallowed decays.

Testing the effectiveness of monolayers under wind and wave conditions.

PubMed

Palada, C; Schouten, P; Lemckert, C

2012-01-01

Monolayers are highly desirable for their evaporation reducing capabilities due to their relatively minimal cost and ease of application. Despite these positive attributes, monolayers have consistently failed to perform effectively due to the harsh wind and wave conditions prevalent across real-world water reserves. An exhaustive and consistent study testing the influence of wind and wave combinations on monolayer performance has yet to be presented in the literature. To remedy this, the effect of simultaneous wind and wave conditions on a benchmark high-performance monolayer (octadecanol suspension, CH(3)(CH(2))(16)CH(2)OH) has been analysed. Subjected only to waves, the monolayer remained intact due to its innate ability to compress and expand. However, the constant simultaneous application of wind and waves caused the monolayer to break up and gather down-wind where it volatilised over time. At wind speeds above 1.3 m s(-1) the monolayer was completely ineffective. For wind speeds below this threshold, the monolayer had an influence on the evaporation rate dependent on wind speed. From these results a series of application protocols can now be developed for the optimised deployment of monolayers in real-world water reserves. This will be of interest to private, commercial and government organisations involved in the storage and management of water resources.

Benchmarking all-atom simulations using hydrogen exchange

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skinner, John J.; Yu, Wookyung; Gichana, Elizabeth K.

We are now able to fold small proteins reversibly to their native structures [Lindorff-Larsen K, Piana S, Dror RO, Shaw DE (2011) Science 334(6055):517–520] using long-time molecular dynamics (MD) simulations. Our results indicate that modern force fields can reproduce the energy surface near the native structure. In this paper, to test how well the force fields recapitulate the other regions of the energy surface, MD trajectories for a variant of protein G are compared with data from site-resolved hydrogen exchange (HX) and other biophysical measurements. Because HX monitors the breaking of individual H-bonds, this experimental technique identifies the stability andmore » H-bond content of excited states, thus enabling quantitative comparison with the simulations. Contrary to experimental findings of a cooperative, all-or-none unfolding process, the simulated denatured state ensemble, on average, is highly collapsed with some transient or persistent native 2° structure. The MD trajectories of this protein G variant and other small proteins exhibit excessive intramolecular H-bonding even for the most expanded conformations, suggesting that the force fields require improvements in describing H-bonding and backbone hydration. Finally and moreover, these comparisons provide a general protocol for validating the ability of simulations to accurately capture rare structural fluctuations.« less

Space Weathering Experiments on Spacecraft Materials

NASA Technical Reports Server (NTRS)

Engelhart, D. P.; Cooper, R.; Cowardin, H.; Maxwell, J.; Plis, E.; Ferguson, D.; Barton, D.; Schiefer, S.; Hoffmann, R.

2017-01-01

A project to investigate space environment effects on specific materials with interest to remote sensing was initiated in 2016. The goal of the project is to better characterize changes in the optical properties of polymers found in multi-layered spacecraft insulation (MLI) induced by electron bombardment. Previous analysis shows that chemical bonds break and potentially reform when exposed to high energy electrons like those seen in orbit. These chemical changes have been shown to alter a material's optical reflectance, among other material properties. This paper presents the initial experimental results of MLI materials exposed to various fluences of high energy electrons, designed to simulate a portion of the geosynchronous Earth orbit (GEO) space environment. It is shown that the spectral reflectance of some of the tested materials changes as a function of electron dose. These results provide an experimental benchmark for analysis of aging effects on satellite systems which can be used to improve remote sensing and space situational awareness. They also provide preliminary analysis on those materials that are most likely to comprise the high area-to-mass ratio (HAMR) population of space debris in the geosynchronous orbit environment. Finally, the results presented in this paper serve as a proof of concept for simulated environmental aging of spacecraft polymers that should lead to more experiments using a larger subset of spacecraft materials.

Towards molecular electronics with large-area molecular junctions.

PubMed

Akkerman, Hylke B; Blom, Paul W M; de Leeuw, Dago M; de Boer, Bert

2006-05-04

Electronic transport through single molecules has been studied extensively by academic and industrial research groups. Discrete tunnel junctions, or molecular diodes, have been reported using scanning probes, break junctions, metallic crossbars and nanopores. For technological applications, molecular tunnel junctions must be reliable, stable and reproducible. The conductance per molecule, however, typically varies by many orders of magnitude. Self-assembled monolayers (SAMs) may offer a promising route to the fabrication of reliable devices, and charge transport through SAMs of alkanethiols within nanopores is well understood, with non-resonant tunnelling dominating the transport mechanism. Unfortunately, electrical shorts in SAMs are often formed upon vapour deposition of the top electrode, which limits the diameter of the nanopore diodes to about 45 nm. Here we demonstrate a method to manufacture molecular junctions with diameters up to 100 microm with high yields (> 95 per cent). The junctions show excellent stability and reproducibility, and the conductance per unit area is similar to that obtained for benchmark nanopore diodes. Our technique involves processing the molecular junctions in the holes of a lithographically patterned photoresist, and then inserting a conducting polymer interlayer between the SAM and the metal top electrode. This simple approach is potentially low-cost and could pave the way for practical molecular electronics.

Benchmarking all-atom simulations using hydrogen exchange

DOE PAGES

Skinner, John J.; Yu, Wookyung; Gichana, Elizabeth K.; ...

2014-10-27

We are now able to fold small proteins reversibly to their native structures [Lindorff-Larsen K, Piana S, Dror RO, Shaw DE (2011) Science 334(6055):517–520] using long-time molecular dynamics (MD) simulations. Our results indicate that modern force fields can reproduce the energy surface near the native structure. In this paper, to test how well the force fields recapitulate the other regions of the energy surface, MD trajectories for a variant of protein G are compared with data from site-resolved hydrogen exchange (HX) and other biophysical measurements. Because HX monitors the breaking of individual H-bonds, this experimental technique identifies the stability andmore » H-bond content of excited states, thus enabling quantitative comparison with the simulations. Contrary to experimental findings of a cooperative, all-or-none unfolding process, the simulated denatured state ensemble, on average, is highly collapsed with some transient or persistent native 2° structure. The MD trajectories of this protein G variant and other small proteins exhibit excessive intramolecular H-bonding even for the most expanded conformations, suggesting that the force fields require improvements in describing H-bonding and backbone hydration. Finally and moreover, these comparisons provide a general protocol for validating the ability of simulations to accurately capture rare structural fluctuations.« less

Unified scenario for composite right-handed neutrinos and dark matter

NASA Astrophysics Data System (ADS)

Davoudiasl, Hooman; Giardino, Pier Paolo; Neil, Ethan T.; Rinaldi, Enrico

2017-12-01

We entertain the possibility that neutrino masses and dark matter (DM) originate from a common composite dark sector. A minimal effective theory can be constructed based on a dark S U (3 )D interaction with three flavors of massless dark quarks; electroweak symmetry breaking gives masses to the dark quarks. By assigning a Z2 charge to one flavor, a stable "dark kaon" can provide a good thermal relic DM candidate. We find that "dark neutrons" may be identified as right handed Dirac neutrinos. Some level of "neutron-anti-neutron" oscillation in the dark sector can then result in non-zero Majorana masses for light standard model neutrinos. A simple ultraviolet completion is presented, involving additional heavy S U (3 )D-charged particles with electroweak and lepton Yukawa couplings. At our benchmark point, there are "dark pions" that are much lighter than the Higgs and we expect spectacular collider signals arising from the UV framework. This includes the decay of the Higgs boson to τ τ ℓℓ', where ℓ(ℓ') can be any lepton, with displaced vertices. We discuss the observational signatures of this UV framework in dark matter searches and primordial gravitational wave experiments; the latter signature is potentially correlated with the H →τ τ ℓℓ' decay.

A new insight into the phase transition in the early Universe with two Higgs doublets

NASA Astrophysics Data System (ADS)

Bernon, Jérémy; Bian, Ligong; Jiang, Yun

2018-05-01

We study the electroweak phase transition in the alignment limit of the CP-conserving two-Higgs-doublet model (2HDM) of Type I and Type II. The effective potential is evaluated at one-loop, where the thermal potential includes Daisy corrections and is reliably approximated by means of a sum of Bessel functions. Both 1-stage and 2-stage electroweak phase transitions are shown to be possible, depending on the pattern of the vacuum development as the Universe cools down. For the 1-stage case focused on in this paper, we analyze the properties of phase transition and discover that the field value of the electroweak symmetry breaking vacuum at the critical temperature at which the first order phase transition occurs is largely correlated with the vacuum depth of the 1-loop potential at zero temperature. We demonstrate that a strong first order electroweak phase transition (SFOEWPT) in the 2HDM is achievable and establish benchmark scenarios leading to different testable signatures at colliders. In addition, we verify that an enhanced triple Higgs coupling (including loop corrections) is a typical feature of the SFOPT driven by the additional doublet. As a result, SFOEWPT might be able to be probed at the LHC and future lepton colliders through Higgs pair production.

Human-mediated loss of phylogenetic and functional diversity in coral reef fishes.

PubMed

D'agata, Stéphanie; Mouillot, David; Kulbicki, Michel; Andréfouët, Serge; Bellwood, David R; Cinner, Joshua E; Cowman, Peter F; Kronen, Mecki; Pinca, Silvia; Vigliola, Laurent

2014-03-03

Beyond the loss of species richness, human activities may also deplete the breadth of evolutionary history (phylogenetic diversity) and the diversity of roles (functional diversity) carried out by species within communities, two overlooked components of biodiversity. Both are, however, essential to sustain ecosystem functioning and the associated provision of ecosystem services, particularly under fluctuating environmental conditions. We quantified the effect of human activities on the taxonomic, phylogenetic, and functional diversity of fish communities in coral reefs, while teasing apart the influence of biogeography and habitat along a gradient of human pressure across the Pacific Ocean. We detected nonlinear relationships with significant breaking points in the impact of human population density on phylogenetic and functional diversity of parrotfishes, at 25 and 15 inhabitants/km(2), respectively, while parrotfish species richness decreased linearly along the same population gradient. Over the whole range, species richness decreased by 11.7%, while phylogenetic and functional diversity dropped by 35.8% and 46.6%, respectively. Our results call for caution when using species richness as a benchmark for measuring the status of ecosystems since it appears to be less responsive to variation in human population densities than its phylogenetic and functional counterparts, potentially imperiling the functioning of coral reef ecosystems. Copyright © 2014 Elsevier Ltd. All rights reserved.

Derivation of Draft Ecological Soil Screening Levels for TNT and RDX Utilizing Terrestrial Plant and Soil Invertebrate Toxicity Benchmarks

DTIC Science & Technology

2012-11-01

TSL Soils Utilizing Growth Benchmarks for Alfalfa , Barnyard Grass, and Perennial Ryegrass ............................................. 5 3...Derivation of Terrestrial Plant-Based Draft Eco-SSL Value for RDX Weathered-and-Aged in SSL or TSL Soils Utilizing Growth Benchmarks for Alfalfa ...studies were conducted using the following plant species:  Dicotyledonous symbiotic species alfalfa (Medicago sativa L.)  Monocotyledonous

Simple Benchmark Specifications for Space Radiation Protection

NASA Technical Reports Server (NTRS)

Singleterry, Robert C. Jr.; Aghara, Sukesh K.

2013-01-01

This report defines space radiation benchmark specifications. This specification starts with simple, monoenergetic, mono-directional particles on slabs and progresses to human models in spacecraft. This report specifies the models and sources needed to what the team performing the benchmark needs to produce in a report. Also included are brief descriptions of how OLTARIS, the NASA Langley website for space radiation analysis, performs its analysis.

From Innovative Programs to Systemic Education Reform: Lesson from Five Communities. The Final Report of the Benchmark Communities Initiative.

ERIC Educational Resources Information Center

DeSalvatore, Larry; Goldberger, Susan; Steinberg, Adria

This document presents the lessons of Jobs for the Future's Benchmark Communities Initiative (BCI), a 5-year systemic educational reform initiative launched in 1994 in five communities. Before joining the BCI, the five Benchmark communities had each begun a school-to-career effort. Five key findings from the BCI are outlined: (1) students engaged…

Benchmarking U.S. Small Wind Costs with the Distributed Wind Taxonomy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orrell, Alice C.; Poehlman, Eric A.

The objective of this report is to benchmark costs for small wind projects installed in the United States using a distributed wind taxonomy. Consequently, this report is a starting point to help expand the U.S. distributed wind market by informing potential areas for small wind cost-reduction opportunities and providing a benchmark to track future small wind cost-reduction progress.

Performance of Multi-chaotic PSO on a shifted benchmark functions set

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pluhacek, Michal; Senkerik, Roman; Zelinka, Ivan

2015-03-10

In this paper the performance of Multi-chaotic PSO algorithm is investigated using two shifted benchmark functions. The purpose of shifted benchmark functions is to simulate the time-variant real-world problems. The results of chaotic PSO are compared with canonical version of the algorithm. It is concluded that using the multi-chaotic approach can lead to better results in optimization of shifted functions.

Benchmarking: contexts and details matter.

PubMed

Zheng, Siyuan

2017-07-05

Benchmarking is an essential step in the development of computational tools. We take this opportunity to pitch in our opinions on tool benchmarking, in light of two correspondence articles published in Genome Biology.Please see related Li et al. and Newman et al. correspondence articles: www.dx.doi.org/10.1186/s13059-017-1256-5 and www.dx.doi.org/10.1186/s13059-017-1257-4.

Implementation and verification of global optimization benchmark problems

NASA Astrophysics Data System (ADS)

Posypkin, Mikhail; Usov, Alexander

2017-12-01

The paper considers the implementation and verification of a test suite containing 150 benchmarks for global deterministic box-constrained optimization. A C++ library for describing standard mathematical expressions was developed for this purpose. The library automate the process of generating the value of a function and its' gradient at a given point and the interval estimates of a function and its' gradient on a given box using a single description. Based on this functionality, we have developed a collection of tests for an automatic verification of the proposed benchmarks. The verification has shown that literary sources contain mistakes in the benchmarks description. The library and the test suite are available for download and can be used freely.

Memory-Intensive Benchmarks: IRAM vs. Cache-Based Machines

NASA Technical Reports Server (NTRS)

Biswas, Rupak; Gaeke, Brian R.; Husbands, Parry; Li, Xiaoye S.; Oliker, Leonid; Yelick, Katherine A.; Biegel, Bryan (Technical Monitor)

2002-01-01

The increasing gap between processor and memory performance has lead to new architectural models for memory-intensive applications. In this paper, we explore the performance of a set of memory-intensive benchmarks and use them to compare the performance of conventional cache-based microprocessors to a mixed logic and DRAM processor called VIRAM. The benchmarks are based on problem statements, rather than specific implementations, and in each case we explore the fundamental hardware requirements of the problem, as well as alternative algorithms and data structures that can help expose fine-grained parallelism or simplify memory access patterns. The benchmarks are characterized by their memory access patterns, their basic control structures, and the ratio of computation to memory operation.

Standardised Benchmarking in the Quest for Orthologs

PubMed Central

Altenhoff, Adrian M.; Boeckmann, Brigitte; Capella-Gutierrez, Salvador; Dalquen, Daniel A.; DeLuca, Todd; Forslund, Kristoffer; Huerta-Cepas, Jaime; Linard, Benjamin; Pereira, Cécile; Pryszcz, Leszek P.; Schreiber, Fabian; Sousa da Silva, Alan; Szklarczyk, Damian; Train, Clément-Marie; Bork, Peer; Lecompte, Odile; von Mering, Christian; Xenarios, Ioannis; Sjölander, Kimmen; Juhl Jensen, Lars; Martin, Maria J.; Muffato, Matthieu; Gabaldón, Toni; Lewis, Suzanna E.; Thomas, Paul D.; Sonnhammer, Erik; Dessimoz, Christophe

2016-01-01

The identification of evolutionarily related genes across different species—orthologs in particular—forms the backbone of many comparative, evolutionary, and functional genomic analyses. Achieving high accuracy in orthology inference is thus essential. Yet the true evolutionary history of genes, required to ascertain orthology, is generally unknown. Furthermore, orthologs are used for very different applications across different phyla, with different requirements in terms of the precision-recall trade-off. As a result, assessing the performance of orthology inference methods remains difficult for both users and method developers. Here, we present a community effort to establish standards in orthology benchmarking and facilitate orthology benchmarking through an automated web-based service (http://orthology.benchmarkservice.org). Using this new service, we characterise the performance of 15 well-established orthology inference methods and resources on a battery of 20 different benchmarks. Standardised benchmarking provides a way for users to identify the most effective methods for the problem at hand, sets a minimal requirement for new tools and resources, and guides the development of more accurate orthology inference methods. PMID:27043882

Benchmarking CRISPR on-target sgRNA design.

PubMed

Yan, Jifang; Chuai, Guohui; Zhou, Chi; Zhu, Chenyu; Yang, Jing; Zhang, Chao; Gu, Feng; Xu, Han; Wei, Jia; Liu, Qi

2017-02-15

CRISPR (Clustered Regularly Interspaced Short Palindromic Repeats)-based gene editing has been widely implemented in various cell types and organisms. A major challenge in the effective application of the CRISPR system is the need to design highly efficient single-guide RNA (sgRNA) with minimal off-target cleavage. Several tools are available for sgRNA design, while limited tools were compared. In our opinion, benchmarking the performance of the available tools and indicating their applicable scenarios are important issues. Moreover, whether the reported sgRNA design rules are reproducible across different sgRNA libraries, cell types and organisms remains unclear. In our study, a systematic and unbiased benchmark of the sgRNA predicting efficacy was performed on nine representative on-target design tools, based on six benchmark data sets covering five different cell types. The benchmark study presented here provides novel quantitative insights into the available CRISPR tools. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Algorithm and Architecture Independent Benchmarking with SEAK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tallent, Nathan R.; Manzano Franco, Joseph B.; Gawande, Nitin A.

2016-05-23

Many applications of high performance embedded computing are limited by performance or power bottlenecks. We have designed the Suite for Embedded Applications & Kernels (SEAK), a new benchmark suite, (a) to capture these bottlenecks in a way that encourages creative solutions; and (b) to facilitate rigorous, objective, end-user evaluation for their solutions. To avoid biasing solutions toward existing algorithms, SEAK benchmarks use a mission-centric (abstracted from a particular algorithm) and goal-oriented (functional) specification. To encourage solutions that are any combination of software or hardware, we use an end-user black-box evaluation that can capture tradeoffs between performance, power, accuracy, size, andmore » weight. The tradeoffs are especially informative for procurement decisions. We call our benchmarks future proof because each mission-centric interface and evaluation remains useful despite shifting algorithmic preferences. It is challenging to create both concise and precise goal-oriented specifications for mission-centric problems. This paper describes the SEAK benchmark suite and presents an evaluation of sample solutions that highlights power and performance tradeoffs.« less

Revisiting Yasinsky and Henry`s benchmark using modern nodal codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feltus, M.A.; Becker, M.W.

1995-12-31

The numerical experiments analyzed by Yasinsky and Henry are quite trivial by comparison with today`s standards because they used the finite difference code WIGLE for their benchmark. Also, this problem is a simple slab (one-dimensional) case with no feedback mechanisms. This research attempts to obtain STAR (Ref. 2) and NEM (Ref. 3) code results in order to produce a more modern kinetics benchmark with results comparable WIGLE.

Implementation of the NAS Parallel Benchmarks in Java

NASA Technical Reports Server (NTRS)

Frumkin, Michael A.; Schultz, Matthew; Jin, Haoqiang; Yan, Jerry; Biegel, Bryan (Technical Monitor)

2002-01-01

Several features make Java an attractive choice for High Performance Computing (HPC). In order to gauge the applicability of Java to Computational Fluid Dynamics (CFD), we have implemented the NAS (NASA Advanced Supercomputing) Parallel Benchmarks in Java. The performance and scalability of the benchmarks point out the areas where improvement in Java compiler technology and in Java thread implementation would position Java closer to Fortran in the competition for CFD applications.

Performance and Scalability of the NAS Parallel Benchmarks in Java

NASA Technical Reports Server (NTRS)

Frumkin, Michael A.; Schultz, Matthew; Jin, Haoqiang; Yan, Jerry; Biegel, Bryan A. (Technical Monitor)

2002-01-01

Several features make Java an attractive choice for scientific applications. In order to gauge the applicability of Java to Computational Fluid Dynamics (CFD), we have implemented the NAS (NASA Advanced Supercomputing) Parallel Benchmarks in Java. The performance and scalability of the benchmarks point out the areas where improvement in Java compiler technology and in Java thread implementation would position Java closer to Fortran in the competition for scientific applications.

A Standard-Setting Study to Establish College Success Criteria to Inform the SAT® College and Career Readiness Benchmark. Research Report 2012-3

ERIC Educational Resources Information Center

Kobrin, Jennifer L.; Patterson, Brian F.; Wiley, Andrew; Mattern, Krista D.

2012-01-01

In 2011, the College Board released its SAT college and career readiness benchmark, which represents the level of academic preparedness associated with a high likelihood of college success and completion. The goal of this study, which was conducted in 2008, was to establish college success criteria to inform the development of the benchmark. The…

The Army Pollution Prevention Program: Improving Performance Through Benchmarking.

DTIC Science & Technology

1995-06-01

Washington, DC 20503. 1. AGENCY USE ONLY (Leave Blank) 2. REPORT DATE June 1995 3. REPORT TYPE AND DATES COVERED Final 4. TITLE AND SUBTITLE...unlimited 12b. DISTRIBUTION CODE 13. ABSTRACT (Maximum 200 words) This report investigates the feasibility of using benchmarking as a method for...could use to determine to what degree it should integrate benchmarking with other quality management tools to support the pollution prevention program

Benchmarking hypercube hardware and software

NASA Technical Reports Server (NTRS)

Grunwald, Dirk C.; Reed, Daniel A.

1986-01-01

It was long a truism in computer systems design that balanced systems achieve the best performance. Message passing parallel processors are no different. To quantify the balance of a hypercube design, an experimental methodology was developed and the associated suite of benchmarks was applied to several existing hypercubes. The benchmark suite includes tests of both processor speed in the absence of internode communication and message transmission speed as a function of communication patterns.

Evaluation of the ACEC Benchmark Suite for Real-Time Applications

DTIC Science & Technology

1990-07-23

1.0 benchmark suite waSanalyzed with respect to its measuring of Ada real-time features such as tasking, memory management, input/output, scheduling...and delay statement, Chapter 13 features , pragmas, interrupt handling, subprogram overhead, numeric computations etc. For most of the features that...meant for programming real-time systems. The ACEC benchmarks have been analyzed extensively with respect to their measuring of Ada real-time features

Implementing a benchmarking and feedback concept decreases postoperative pain after total knee arthroplasty: A prospective study including 256 patients.

PubMed

Benditz, A; Drescher, J; Greimel, F; Zeman, F; Grifka, J; Meißner, W; Völlner, F

2016-12-05

Perioperative pain reduction, particularly during the first two days, is highly important for patients after total knee arthroplasty (TKA). Problems are not only caused by medical issues but by organization and hospital structure. The present study shows how the quality of pain management can be increased by implementing a standardized pain concept and simple, consistent benchmarking. All patients included into the study had undergone total knee arthroplasty. Outcome parameters were analyzed by means of a questionnaire on the first postoperative day. A multidisciplinary team implemented a regular procedure of data analyzes and external benchmarking by participating in a nationwide quality improvement project. At the beginning of the study, our hospital ranked 16 th in terms of activity-related pain and 9 th in patient satisfaction among 47 anonymized hospitals participating in the benchmarking project. At the end of the study, we had improved to 1 st activity-related pain and to 2 nd in patient satisfaction. Although benchmarking started and finished with the same standardized pain management concept, results were initially pure. Beside pharmacological treatment, interdisciplinary teamwork and benchmarking with direct feedback mechanisms are also very important for decreasing postoperative pain and for increasing patient satisfaction after TKA.

Implementing a benchmarking and feedback concept decreases postoperative pain after total knee arthroplasty: A prospective study including 256 patients

PubMed Central

Benditz, A.; Drescher, J.; Greimel, F.; Zeman, F.; Grifka, J.; Meißner, W.; Völlner, F.

2016-01-01

Perioperative pain reduction, particularly during the first two days, is highly important for patients after total knee arthroplasty (TKA). Problems are not only caused by medical issues but by organization and hospital structure. The present study shows how the quality of pain management can be increased by implementing a standardized pain concept and simple, consistent benchmarking. All patients included into the study had undergone total knee arthroplasty. Outcome parameters were analyzed by means of a questionnaire on the first postoperative day. A multidisciplinary team implemented a regular procedure of data analyzes and external benchmarking by participating in a nationwide quality improvement project. At the beginning of the study, our hospital ranked 16th in terms of activity-related pain and 9th in patient satisfaction among 47 anonymized hospitals participating in the benchmarking project. At the end of the study, we had improved to 1st activity-related pain and to 2nd in patient satisfaction. Although benchmarking started and finished with the same standardized pain management concept, results were initially pure. Beside pharmacological treatment, interdisciplinary teamwork and benchmarking with direct feedback mechanisms are also very important for decreasing postoperative pain and for increasing patient satisfaction after TKA. PMID:27917911

Closed-Loop Neuromorphic Benchmarks

PubMed Central

Stewart, Terrence C.; DeWolf, Travis; Kleinhans, Ashley; Eliasmith, Chris

2015-01-01

Evaluating the effectiveness and performance of neuromorphic hardware is difficult. It is even more difficult when the task of interest is a closed-loop task; that is, a task where the output from the neuromorphic hardware affects some environment, which then in turn affects the hardware's future input. However, closed-loop situations are one of the primary potential uses of neuromorphic hardware. To address this, we present a methodology for generating closed-loop benchmarks that makes use of a hybrid of real physical embodiment and a type of “minimal” simulation. Minimal simulation has been shown to lead to robust real-world performance, while still maintaining the practical advantages of simulation, such as making it easy for the same benchmark to be used by many researchers. This method is flexible enough to allow researchers to explicitly modify the benchmarks to identify specific task domains where particular hardware excels. To demonstrate the method, we present a set of novel benchmarks that focus on motor control for an arbitrary system with unknown external forces. Using these benchmarks, we show that an error-driven learning rule can consistently improve motor control performance across a randomly generated family of closed-loop simulations, even when there are up to 15 interacting joints to be controlled. PMID:26696820

Funnel plot control limits to identify poorly performing healthcare providers when there is uncertainty in the value of the benchmark.

PubMed

Manktelow, Bradley N; Seaton, Sarah E; Evans, T Alun

2016-12-01

There is an increasing use of statistical methods, such as funnel plots, to identify poorly performing healthcare providers. Funnel plots comprise the construction of control limits around a benchmark and providers with outcomes falling outside the limits are investigated as potential outliers. The benchmark is usually estimated from observed data but uncertainty in this estimate is usually ignored when constructing control limits. In this paper, the use of funnel plots in the presence of uncertainty in the value of the benchmark is reviewed for outcomes from a Binomial distribution. Two methods to derive the control limits are shown: (i) prediction intervals; (ii) tolerance intervals Tolerance intervals formally include the uncertainty in the value of the benchmark while prediction intervals do not. The probability properties of 95% control limits derived using each method were investigated through hypothesised scenarios. Neither prediction intervals nor tolerance intervals produce funnel plot control limits that satisfy the nominal probability characteristics when there is uncertainty in the value of the benchmark. This is not necessarily to say that funnel plots have no role to play in healthcare, but that without the development of intervals satisfying the nominal probability characteristics they must be interpreted with care. © The Author(s) 2014.

Development and Application of Benchmark Examples for Mixed-Mode I/II Quasi-Static Delamination Propagation Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2012-01-01

The development of benchmark examples for quasi-static delamination propagation prediction is presented and demonstrated for a commercial code. The examples are based on finite element models of the Mixed-Mode Bending (MMB) specimen. The examples are independent of the analysis software used and allow the assessment of the automated delamination propagation prediction capability in commercial finite element codes based on the virtual crack closure technique (VCCT). First, quasi-static benchmark examples were created for the specimen. Second, starting from an initially straight front, the delamination was allowed to propagate under quasi-static loading. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Good agreement between the results obtained from the automated propagation analysis and the benchmark results could be achieved by selecting input parameters that had previously been determined during analyses of mode I Double Cantilever Beam and mode II End Notched Flexure specimens. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Overall the results are encouraging, but further assessment for mixed-mode delamination fatigue onset and growth is required.

An automated protocol for performance benchmarking a widefield fluorescence microscope.

PubMed

Halter, Michael; Bier, Elianna; DeRose, Paul C; Cooksey, Gregory A; Choquette, Steven J; Plant, Anne L; Elliott, John T

2014-11-01

Widefield fluorescence microscopy is a highly used tool for visually assessing biological samples and for quantifying cell responses. Despite its widespread use in high content analysis and other imaging applications, few published methods exist for evaluating and benchmarking the analytical performance of a microscope. Easy-to-use benchmarking methods would facilitate the use of fluorescence imaging as a quantitative analytical tool in research applications, and would aid the determination of instrumental method validation for commercial product development applications. We describe and evaluate an automated method to characterize a fluorescence imaging system's performance by benchmarking the detection threshold, saturation, and linear dynamic range to a reference material. The benchmarking procedure is demonstrated using two different materials as the reference material, uranyl-ion-doped glass and Schott 475 GG filter glass. Both are suitable candidate reference materials that are homogeneously fluorescent and highly photostable, and the Schott 475 GG filter glass is currently commercially available. In addition to benchmarking the analytical performance, we also demonstrate that the reference materials provide for accurate day to day intensity calibration. Published 2014 Wiley Periodicals Inc. Published 2014 Wiley Periodicals Inc. This article is a US government work and, as such, is in the public domain in the United States of America.

CompaRNA: a server for continuous benchmarking of automated methods for RNA secondary structure prediction

PubMed Central

Puton, Tomasz; Kozlowski, Lukasz P.; Rother, Kristian M.; Bujnicki, Janusz M.

2013-01-01

We present a continuous benchmarking approach for the assessment of RNA secondary structure prediction methods implemented in the CompaRNA web server. As of 3 October 2012, the performance of 28 single-sequence and 13 comparative methods has been evaluated on RNA sequences/structures released weekly by the Protein Data Bank. We also provide a static benchmark generated on RNA 2D structures derived from the RNAstrand database. Benchmarks on both data sets offer insight into the relative performance of RNA secondary structure prediction methods on RNAs of different size and with respect to different types of structure. According to our tests, on the average, the most accurate predictions obtained by a comparative approach are generated by CentroidAlifold, MXScarna, RNAalifold and TurboFold. On the average, the most accurate predictions obtained by single-sequence analyses are generated by CentroidFold, ContextFold and IPknot. The best comparative methods typically outperform the best single-sequence methods if an alignment of homologous RNA sequences is available. This article presents the results of our benchmarks as of 3 October 2012, whereas the rankings presented online are continuously updated. We will gladly include new prediction methods and new measures of accuracy in the new editions of CompaRNA benchmarks. PMID:23435231

Benchmarking health IT among OECD countries: better data for better policy

PubMed Central

Adler-Milstein, Julia; Ronchi, Elettra; Cohen, Genna R; Winn, Laura A Pannella; Jha, Ashish K

2014-01-01

Objective To develop benchmark measures of health information and communication technology (ICT) use to facilitate cross-country comparisons and learning. Materials and methods The effort is led by the Organisation for Economic Co-operation and Development (OECD). Approaches to definition and measurement within four ICT domains were compared across seven OECD countries in order to identify functionalities in each domain. These informed a set of functionality-based benchmark measures, which were refined in collaboration with representatives from more than 20 OECD and non-OECD countries. We report on progress to date and remaining work to enable countries to begin to collect benchmark data. Results The four benchmarking domains include provider-centric electronic record, patient-centric electronic record, health information exchange, and tele-health. There was broad agreement on functionalities in the provider-centric electronic record domain (eg, entry of core patient data, decision support), and less agreement in the other three domains in which country representatives worked to select benchmark functionalities. Discussion Many countries are working to implement ICTs to improve healthcare system performance. Although many countries are looking to others as potential models, the lack of consistent terminology and approach has made cross-national comparisons and learning difficult. Conclusions As countries develop and implement strategies to increase the use of ICTs to promote health goals, there is a historic opportunity to enable cross-country learning. To facilitate this learning and reduce the chances that individual countries flounder, a common understanding of health ICT adoption and use is needed. The OECD-led benchmarking process is a crucial step towards achieving this. PMID:23721983

Evaluation of the influence of the definition of an isolated hip fracture as an exclusion criterion for trauma system benchmarking: a multicenter cohort study.

PubMed

Tiao, J; Moore, L; Porgo, T V; Belcaid, A

2016-06-01

To assess whether the definition of an IHF used as an exclusion criterion influences the results of trauma center benchmarking. We conducted a multicenter retrospective cohort study with data from an integrated Canadian trauma system. The study population included all patients admitted between 1999 and 2010 to any of the 57 adult trauma centers. Seven definitions of IHF based on diagnostic codes, age, mechanism of injury, and secondary injuries, identified in a systematic review, were used. Trauma centers were benchmarked using risk-adjusted mortality estimates generated using the Trauma Risk Adjustment Model. The agreement between benchmarking results generated under different IHF definitions was evaluated with correlation coefficients on adjusted mortality estimates. Correlation coefficients >0.95 were considered to convey acceptable agreement. The study population consisted of 172,872 patients before exclusion of IHF and between 128,094 and 139,588 patients after exclusion. Correlation coefficients between risk-adjusted mortality estimates generated in populations including and excluding IHF varied between 0.86 and 0.90. Correlation coefficients of estimates generated under different definitions of IHF varied between 0.97 and 0.99, even when analyses were restricted to patients aged ≥65 years. Although the exclusion of patients with IHF has an influence on the results of trauma center benchmarking based on mortality, the definition of IHF in terms of diagnostic codes, age, mechanism of injury and secondary injury has no significant impact on benchmarking results. Results suggest that there is no need to obtain formal consensus on the definition of IHF for benchmarking activities.

Contributions to Integral Nuclear Data in ICSBEP and IRPhEP since ND 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bess, John D.; Briggs, J. Blair; Gulliford, Jim

2016-09-01

The status of the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and the International Reactor Physics Experiment Evaluation Project (IRPhEP) was last discussed directly with the international nuclear data community at ND2013. Since ND2013, integral benchmark data that are available for nuclear data testing has continued to increase. The status of the international benchmark efforts and the latest contributions to integral nuclear data for testing is discussed. Select benchmark configurations that have been added to the ICSBEP and IRPhEP Handbooks since ND2013 are highlighted. The 2015 edition of the ICSBEP Handbook now contains 567 evaluations with benchmark specifications for 4,874more » critical, near-critical, or subcritical configurations, 31 criticality alarm placement/shielding configuration with multiple dose points apiece, and 207 configurations that have been categorized as fundamental physics measurements that are relevant to criticality safety applications. The 2015 edition of the IRPhEP Handbook contains data from 143 different experimental series that were performed at 50 different nuclear facilities. Currently 139 of the 143 evaluations are published as approved benchmarks with the remaining four evaluations published in draft format only. Measurements found in the IRPhEP Handbook include criticality, buckling and extrapolation length, spectral characteristics, reactivity effects, reactivity coefficients, kinetics, reaction-rate distributions, power distributions, isotopic compositions, and/or other miscellaneous types of measurements for various types of reactor systems. Annual technical review meetings for both projects were held in April 2016; additional approved benchmark evaluations will be included in the 2016 editions of these handbooks.« less

Benchmarking routine psychological services: a discussion of challenges and methods.

PubMed

Delgadillo, Jaime; McMillan, Dean; Leach, Chris; Lucock, Mike; Gilbody, Simon; Wood, Nick

2014-01-01

Policy developments in recent years have led to important changes in the level of access to evidence-based psychological treatments. Several methods have been used to investigate the effectiveness of these treatments in routine care, with different approaches to outcome definition and data analysis. To present a review of challenges and methods for the evaluation of evidence-based treatments delivered in routine mental healthcare. This is followed by a case example of a benchmarking method applied in primary care. High, average and poor performance benchmarks were calculated through a meta-analysis of published data from services working under the Improving Access to Psychological Therapies (IAPT) Programme in England. Pre-post treatment effect sizes (ES) and confidence intervals were estimated to illustrate a benchmarking method enabling services to evaluate routine clinical outcomes. High, average and poor performance ES for routine IAPT services were estimated to be 0.91, 0.73 and 0.46 for depression (using PHQ-9) and 1.02, 0.78 and 0.52 for anxiety (using GAD-7). Data from one specific IAPT service exemplify how to evaluate and contextualize routine clinical performance against these benchmarks. The main contribution of this report is to summarize key recommendations for the selection of an adequate set of psychometric measures, the operational definition of outcomes, and the statistical evaluation of clinical performance. A benchmarking method is also presented, which may enable a robust evaluation of clinical performance against national benchmarks. Some limitations concerned significant heterogeneity among data sources, and wide variations in ES and data completeness.

Benchmarking health IT among OECD countries: better data for better policy.

PubMed

Adler-Milstein, Julia; Ronchi, Elettra; Cohen, Genna R; Winn, Laura A Pannella; Jha, Ashish K

2014-01-01

To develop benchmark measures of health information and communication technology (ICT) use to facilitate cross-country comparisons and learning. The effort is led by the Organisation for Economic Co-operation and Development (OECD). Approaches to definition and measurement within four ICT domains were compared across seven OECD countries in order to identify functionalities in each domain. These informed a set of functionality-based benchmark measures, which were refined in collaboration with representatives from more than 20 OECD and non-OECD countries. We report on progress to date and remaining work to enable countries to begin to collect benchmark data. The four benchmarking domains include provider-centric electronic record, patient-centric electronic record, health information exchange, and tele-health. There was broad agreement on functionalities in the provider-centric electronic record domain (eg, entry of core patient data, decision support), and less agreement in the other three domains in which country representatives worked to select benchmark functionalities. Many countries are working to implement ICTs to improve healthcare system performance. Although many countries are looking to others as potential models, the lack of consistent terminology and approach has made cross-national comparisons and learning difficult. As countries develop and implement strategies to increase the use of ICTs to promote health goals, there is a historic opportunity to enable cross-country learning. To facilitate this learning and reduce the chances that individual countries flounder, a common understanding of health ICT adoption and use is needed. The OECD-led benchmarking process is a crucial step towards achieving this.

Medicare Part D Roulette: Potential Implications of Random Assignment and Plan Restrictions

PubMed Central

Patel, Rajul A.; Walberg, Mark P.; Woelfel, Joseph A.; Amaral, Michelle M.; Varu, Paresh

2013-01-01

Background Dual-eligible (Medicare/Medicaid) beneficiaries are randomly assigned to a benchmark plan, which provides prescription drug coverage under the Part D benefit without consideration of their prescription drug profile. To date, the potential for beneficiary assignment to a plan with poor formulary coverage has been minimally studied and the resultant financial impact to beneficiaries unknown. Objective We sought to determine cost variability and drug use restrictions under each available 2010 California benchmark plan. Methods Dual-eligible beneficiaries were provided Part D plan assistance during the 2010 annual election period. The Medicare Web site was used to determine benchmark plan costs and prescription utilization restrictions for each of the six California benchmark plans available for random assignment in 2010. A standardized survey was used to record all de-identified beneficiary demographic and plan specific data. For each low-income subsidy-recipient (n = 113), cost, rank, number of non-formulary medications, and prescription utilization restrictions were recorded for each available 2010 California benchmark plan. Formulary matching rates (percent of beneficiary's medications on plan formulary) were calculated for each benchmark plan. Results Auto-assigned beneficiaries had only a 34% chance of being assigned to the lowest cost plan; the remainder faced potentially significant avoidable out-of-pocket costs. Wide variations between benchmark plans were observed for plan cost, formulary coverage, formulary matching rates, and prescription utilization restrictions. Conclusions Beneficiaries had a 66% chance of being assigned to a sub-optimal plan; thereby, they faced significant avoidable out-of-pocket costs. Alternative methods of beneficiary assignment could decrease beneficiary and Medicare costs while also reducing medication non-compliance. PMID:24753963

Deletions at short direct repeats and base substitutions are characteristic mutations for bleomycin-induced double- and single-strand breaks, respectively, in a human shuttle vector system

NASA Technical Reports Server (NTRS)

Dar, M. E.; Jorgensen, T. J.

1995-01-01

Using the radiomimetic drug, bleomycin, we have determined the mutagenic potential of DNA strand breaks in the shuttle vector pZ189 in human fibroblasts. The bleomycin treatment conditions used produce strand breaks with 3'-phosphoglycolate termini as > 95% of the detectable dose-dependent lesions. Breaks with this end group represent 50% of the strand break damage produced by ionizing radiation. We report that such strand breaks are mutagenic lesions. The type of mutation produced is largely determined by the type of strand break on the plasmid (i.e. single versus double). Mutagenesis studies with purified DNA forms showed that nicked plasmids (i.e. those containing single-strand breaks) predominantly produce base substitutions, the majority of which are multiples, which presumably originate from error-prone polymerase activity at strand break sites. In contrast, repair of linear plasmids (i.e. those containing double-strand breaks) mainly results in deletions at short direct repeat sequences, indicating the involvement of illegitimate recombination. The data characterize the nature of mutations produced by single- and double-strand breaks in human cells, and suggests that deletions at direct repeats may be a 'signature' mutation for the processing of DNA double-strand breaks.

Cbench

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogden, Jeffry B.

2005-09-26

Cbench is intended to be a relatively straightforward collection of tests, benchmarks, applications, utilities, and framework with the goal of facilitating scalable testing and benchmarking of a Linus cluster.