The Influence of Building Codes on Recreation Facility Design.

ERIC Educational Resources Information Center

Morrison, Thomas A.

1989-01-01

Implications of building codes upon design and construction of recreation facilities are investigated (national building codes, recreation facility standards, and misperceptions of design requirements). Recreation professionals can influence architectural designers to correct past deficiencies, but they must understand architectural and…

Energy Cost Impact of Non-Residential Energy Code Requirements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jian; Hart, Philip R.; Rosenberg, Michael I.

2016-08-22

The 2012 International Energy Conservation Code contains 396 separate requirements applicable to non-residential buildings; however, there is no systematic analysis of the energy cost impact of each requirement. Consequently, limited code department budgets for plan review, inspection, and training cannot be focused on the most impactful items. An inventory and ranking of code requirements based on their potential energy cost impact is under development. The initial phase focuses on office buildings with simple HVAC systems in climate zone 4C. Prototype building simulations were used to estimate the energy cost impact of varying levels of non-compliance. A preliminary estimate of themore » probability of occurrence of each level of non-compliance was combined with the estimated lost savings for each level to rank the requirements according to expected savings impact. The methodology to develop and refine further energy cost impacts, specific to building type, system type, and climate location is demonstrated. As results are developed, an innovative alternative method for compliance verification can focus efforts so only the most impactful requirements from an energy cost perspective are verified for every building and a subset of the less impactful requirements are verified on a random basis across a building population. The results can be further applied in prioritizing training material development and specific areas of building official training.« less

An international survey of building energy codes and their implementation

DOE PAGES

Evans, Meredydd; Roshchanka, Volha; Graham, Peter

2017-08-01

Buildings are key to low-carbon development everywhere, and many countries have introduced building energy codes to improve energy efficiency in buildings. Yet, building energy codes can only deliver results when the codes are implemented. For this reason, studies of building energy codes need to consider implementation of building energy codes in a consistent and comprehensive way. This research identifies elements and practices in implementing building energy codes, covering codes in 22 countries that account for 70% of global energy use in buildings. These elements and practices include: comprehensive coverage of buildings by type, age, size, and geographic location; an implementationmore » framework that involves a certified agency to inspect construction at critical stages; and building materials that are independently tested, rated, and labeled. Training and supporting tools are another element of successful code implementation. Some countries have also introduced compliance evaluation studies, which suggested that tightening energy requirements would only be meaningful when also addressing gaps in implementation (Pitt&Sherry, 2014; U.S. DOE, 2016b). Here, this article provides examples of practices that countries have adopted to assist with implementation of building energy codes.« less

An international survey of building energy codes and their implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Meredydd; Roshchanka, Volha; Graham, Peter

Buildings are key to low-carbon development everywhere, and many countries have introduced building energy codes to improve energy efficiency in buildings. Yet, building energy codes can only deliver results when the codes are implemented. For this reason, studies of building energy codes need to consider implementation of building energy codes in a consistent and comprehensive way. This research identifies elements and practices in implementing building energy codes, covering codes in 22 countries that account for 70% of global energy use in buildings. These elements and practices include: comprehensive coverage of buildings by type, age, size, and geographic location; an implementationmore » framework that involves a certified agency to inspect construction at critical stages; and building materials that are independently tested, rated, and labeled. Training and supporting tools are another element of successful code implementation. Some countries have also introduced compliance evaluation studies, which suggested that tightening energy requirements would only be meaningful when also addressing gaps in implementation (Pitt&Sherry, 2014; U.S. DOE, 2016b). Here, this article provides examples of practices that countries have adopted to assist with implementation of building energy codes.« less

Assessing Potential Energy Cost Savings from Increased Energy Code Compliance in Commercial Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, Michael I.; Hart, Philip R.; Athalye, Rahul A.

The US Department of Energy’s most recent commercial energy code compliance evaluation efforts focused on determining a percent compliance rating for states to help them meet requirements under the American Recovery and Reinvestment Act (ARRA) of 2009. That approach included a checklist of code requirements, each of which was graded pass or fail. Percent compliance for any given building was simply the percent of individual requirements that passed. With its binary approach to compliance determination, the previous methodology failed to answer some important questions. In particular, how much energy cost could be saved by better compliance with the commercial energymore » code and what are the relative priorities of code requirements from an energy cost savings perspective? This paper explores an analytical approach and pilot study using a single building type and climate zone to answer those questions.« less

Preserving Envelope Efficiency in Performance Based Code Compliance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, Brian A.; Sullivan, Greg P.; Rosenberg, Michael I.

2015-06-20

The City of Seattle 2012 Energy Code (Seattle 2014), one of the most progressive in the country, is under revision for its 2015 edition. Additionally, city personnel participate in the development of the next generation of the Washington State Energy Code and the International Energy Code. Seattle has pledged carbon neutrality by 2050 including buildings, transportation and other sectors. The United States Department of Energy (DOE), through Pacific Northwest National Laboratory (PNNL) provided technical assistance to Seattle in order to understand the implications of one potential direction for its code development, limiting trade-offs of long-lived building envelope components less stringentmore » than the prescriptive code envelope requirements by using better-than-code but shorter-lived lighting and heating, ventilation, and air-conditioning (HVAC) components through the total building performance modeled energy compliance path. Weaker building envelopes can permanently limit building energy performance even as lighting and HVAC components are upgraded over time, because retrofitting the envelope is less likely and more expensive. Weaker building envelopes may also increase the required size, cost and complexity of HVAC systems and may adversely affect occupant comfort. This report presents the results of this technical assistance. The use of modeled energy code compliance to trade-off envelope components with shorter-lived building components is not unique to Seattle and the lessons and possible solutions described in this report have implications for other jurisdictions and energy codes.« less

41 CFR 102-76.10 - What basic design and construction policy governs Federal agencies?

Code of Federal Regulations, 2014 CFR

2014-01-01

.... (c) Follow nationally recognized model building codes and other applicable nationally recognized codes that govern Federal construction to the maximum extent feasible and consider local building code requirements. (See 40 U.S.C. 3310 and 3312.) (d) Design Federal buildings to have a long life expectancy and...

Building codes : obstacle or opportunity?

Treesearch

Alberto Goetzl; David B. McKeever

1999-01-01

Building codes are critically important in the use of wood products for construction. The codes contain regulations that are prescriptive or performance related for various kinds of buildings and construction types. A prescriptive standard might dictate that a particular type of material be used in a given application. A performance standard requires that a particular...

National Cost-effectiveness of ASHRAE Standard 90.1-2010 Compared to ASHRAE Standard 90.1-2007

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, Brian; Halverson, Mark A.; Myer, Michael

Pacific Northwest National Laboratory (PNNL) completed this project for the U.S. Department of Energy’s (DOE’s) Building Energy Codes Program (BECP). DOE’s BECP supports upgrading building energy codes and standards, and the states’ adoption, implementation, and enforcement of upgraded codes and standards. Building energy codes and standards set minimum requirements for energy-efficient design and construction for new and renovated buildings, and impact energy use and greenhouse gas emissions for the life of buildings. Continuous improvement of building energy efficiency is achieved by periodically upgrading energy codes and standards. Ensuring that changes in the code that may alter costs (for building components,more » initial purchase and installation, replacement, maintenance and energy) are cost-effective encourages their acceptance and implementation. ANSI/ASHRAE/IESNA Standard 90.1 is the energy standard for commercial and multi-family residential buildings over three floors.« less

Cost-effectiveness of ASHRAE Standard 90.1-2010 Compared to ASHRAE Standard 90.1-2007

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, Brian A.; Halverson, Mark A.; Myer, Michael

Pacific Northwest National Laboratory (PNNL) completed this project for the U.S. Department of Energy’s (DOE’s) Building Energy Codes Program (BECP). DOE’s BECP supports upgrading building energy codes and standards, and the states’ adoption, implementation, and enforcement of upgraded codes and standards. Building energy codes and standards set minimum requirements for energy-efficient design and construction for new and renovated buildings, and impact energy use and greenhouse gas emissions for the life of buildings. Continuous improvement of building energy efficiency is achieved by periodically upgrading energy codes and standards. Ensuring that changes in the code that may alter costs (for building components,more » initial purchase and installation, replacement, maintenance and energy) are cost-effective encourages their acceptance and implementation. ANSI/ASHRAE/IESNA Standard 90.1 is the energy standard for commercial and multi-family residential buildings over three floors.« less

24 CFR 200.926c - Model code provisions for use in partially accepted code jurisdictions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... jurisdictions. If a lender or other interested party is notified that a State or local building code has been... in accordance with the applicable State or local building code, plus those additional requirements... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Model code provisions for use in...

24 CFR 200.926c - Model code provisions for use in partially accepted code jurisdictions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... jurisdictions. If a lender or other interested party is notified that a State or local building code has been... in accordance with the applicable State or local building code, plus those additional requirements... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Model code provisions for use in...

24 CFR 200.926c - Model code provisions for use in partially accepted code jurisdictions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... jurisdictions. If a lender or other interested party is notified that a State or local building code has been... in accordance with the applicable State or local building code, plus those additional requirements... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Model code provisions for use in...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dillon, Heather E.; Antonopoulos, Chrissi A.; Solana, Amy E.

As the model energy codes are improved to reach efficiency levels 50 percent greater than current codes, use of on-site renewable energy generation is likely to become a code requirement. This requirement will be needed because traditional mechanisms for code improvement, including envelope, mechanical and lighting, have been pressed to the end of reasonable limits. Research has been conducted to determine the mechanism for implementing this requirement (Kaufman 2011). Kaufmann et al. determined that the most appropriate way to structure an on-site renewable requirement for commercial buildings is to define the requirement in terms of an installed power density permore » unit of roof area. This provides a mechanism that is suitable for the installation of photovoltaic (PV) systems on future buildings to offset electricity and reduce the total building energy load. Kaufmann et al. suggested that an appropriate maximum for the requirement in the commercial sector would be 4 W/ft{sup 2} of roof area or 0.5 W/ft{sup 2} of conditioned floor area. As with all code requirements, there must be an alternative compliance path for buildings that may not reasonably meet the renewables requirement. This might include conditions like shading (which makes rooftop PV arrays less effective), unusual architecture, undesirable roof pitch, unsuitable building orientation, or other issues. In the short term, alternative compliance paths including high performance mechanical equipment, dramatic envelope changes, or controls changes may be feasible. These options may be less expensive than many renewable systems, which will require careful balance of energy measures when setting the code requirement levels. As the stringency of the code continues to increase however, efficiency trade-offs will be maximized, requiring alternative compliance options to be focused solely on renewable electricity trade-offs or equivalent programs. One alternate compliance path includes purchase of Renewable Energy Credits (RECs). Each REC represents a specified amount of renewable electricity production and provides an offset of environmental externalities associated with non-renewable electricity production. The purpose of this paper is to explore the possible issues with RECs and comparable alternative compliance options. Existing codes have been examined to determine energy equivalence between the energy generation requirement and the RECs alternative over the life of the building. The price equivalence of the requirement and the alternative are determined to consider the economic drivers for a market decision. This research includes case studies that review how the few existing codes have incorporated RECs and some of the issues inherent with REC markets. Section 1 of the report reviews compliance options including RECs, green energy purchase programs, shared solar agreements and leases, and other options. Section 2 provides detailed case studies on codes that include RECs and community based alternative compliance methods. The methods the existing code requirements structure alternative compliance options like RECs are the focus of the case studies. Section 3 explores the possible structure of the renewable energy generation requirement in the context of energy and price equivalence. The price of RECs have shown high variation by market and over time which makes it critical to for code language to be updated frequently for a renewable energy generation requirement or the requirement will not remain price-equivalent over time. Section 4 of the report provides a maximum case estimate for impact to the PV market and the REC market based on the Kaufmann et al. proposed requirement levels. If all new buildings in the commercial sector complied with the requirement to install rooftop PV arrays, nearly 4,700 MW of solar would be installed in 2012, a major increase from EIA estimates of 640 MW of solar generation capacity installed in 2009. The residential sector could contribute roughly an additional 2,300 MW based on the same code requirement levels of 4 W/ft{sup 2} of roof area. Section 5 of the report provides a basic framework for draft code language recommendations based on the analysis of the alternative compliance levels.« less

Potential Energy Cost Savings from Increased Commercial Energy Code Compliance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, Michael I.; Hart, Philip R.; Athalye, Rahul A.

2016-08-22

An important question for commercial energy code compliance is: “How much energy cost savings can better compliance achieve?” This question is in sharp contrast to prior efforts that used a checklist of code requirements, each of which was graded pass or fail. Percent compliance for any given building was simply the percent of individual requirements that passed. A field investigation method is being developed that goes beyond the binary approach to determine how much energy cost savings is not realized. Prototype building simulations were used to estimate the energy cost impact of varying levels of non-compliance for newly constructed officemore » buildings in climate zone 4C. Field data collected from actual buildings on specific conditions relative to code requirements was then applied to the simulation results to find the potential lost energy savings for a single building or for a sample of buildings. This new methodology was tested on nine office buildings in climate zone 4C. The amount of additional energy cost savings they could have achieved had they complied fully with the 2012 International Energy Conservation Code is determined. This paper will present the results of the test, lessons learned, describe follow-on research that is needed to verify that the methodology is both accurate and practical, and discuss the benefits that might accrue if the method were widely adopted.« less

75 FR 9434 - Civil Rights Division, Disability Rights Section; Agency Information Collection Activities Under...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-02

... Rights (or his or her designee) may certify that a State or local building code or similar ordinance that establishes accessibility requirements (Code) meets or exceeds the minimum requirements of the ADA for..., Policy and Planning Staff, Justice Management Division, Patrick Henry Building, Suite 1600, 601 D Street...

75 FR 27816 - Civil Rights Division, Disability Rights Section; Agency Information Collection Activities Under...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... certify that a State or local building code or similar ordinance that establishes accessibility requirements (Code) meets or exceeds the minimum requirements of the ADA for accessibility and usability of... Management Division, Patrick Henry Building, Suite 1600, 601 D Street, NW., Washington, DC 20530. Dated: May...

Assessment of codes, by-laws and regulations relating to air wells in building design

NASA Astrophysics Data System (ADS)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

10 CFR 420.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Planning Organization means that organization required by the Department of Transportation, and designated... planning provisions in a Standard Metropolitan Statistical Area. Model Energy Code, 1993, including Errata, means the model building code published by the Council of American Building Officials, which is...

Impacts of Model Building Energy Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Athalye, Rahul A.; Sivaraman, Deepak; Elliott, Douglas B.

The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) periodically evaluates national and state-level impacts associated with energy codes in residential and commercial buildings. Pacific Northwest National Laboratory (PNNL), funded by DOE, conducted an assessment of the prospective impacts of national model building energy codes from 2010 through 2040. A previous PNNL study evaluated the impact of the Building Energy Codes Program; this study looked more broadly at overall code impacts. This report describes the methodology used for the assessment and presents the impacts in terms of energy savings, consumer cost savings, and reduced CO 2 emissions atmore » the state level and at aggregated levels. This analysis does not represent all potential savings from energy codes in the U.S. because it excludes several states which have codes which are fundamentally different from the national model energy codes or which do not have state-wide codes. Energy codes follow a three-phase cycle that starts with the development of a new model code, proceeds with the adoption of the new code by states and local jurisdictions, and finishes when buildings comply with the code. The development of new model code editions creates the potential for increased energy savings. After a new model code is adopted, potential savings are realized in the field when new buildings (or additions and alterations) are constructed to comply with the new code. Delayed adoption of a model code and incomplete compliance with the code’s requirements erode potential savings. The contributions of all three phases are crucial to the overall impact of codes, and are considered in this assessment.« less

Mandating better buildings: a global review of building codes and prospects for improvement in the United States

DOE PAGES

Sun, Xiaojing; Brown, Marilyn A.; Cox, Matt; ...

2015-03-11

This paper provides a global overview of the design, implementation, and evolution of building energy codes. Reflecting alternative policy goals, building energy codes differ significantly across the United States, the European Union, and China. This review uncovers numerous innovative practices including greenhouse gas emissions caps per square meter of building space, energy performance certificates with retrofit recommendations, and inclusion of renewable energy to achieve “nearly zero-energy buildings”. These innovations motivated an assessment of an aggressive commercial building code applied to all US states, requiring both new construction and buildings with major modifications to comply with the latest version of themore » ASHRAE 90.1 Standards. Using the National Energy Modeling System (NEMS), we estimate that by 2035, such building codes in the United States could reduce energy for space heating, cooling, water heating and lighting in commercial buildings by 16%, 15%, 20% and 5%, respectively. Impacts on different fuels and building types, energy rates and bills as well as pollution emission reductions are also examined.« less

Through the Past Decade: How Advanced Energy Design Guides have influenced the Design Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Bing; Athalye, Rahul A.

Advanced Energy Design Guides (AEDGs) were originally developed intended to provide a simple approach to building professionals seeking energy efficient building designs better than ASHRAE Standard 90.1. Since its first book was released in 2004, the AEDG series provided inspiration for the design industry and were seen by designers as a starting point for buildings that wished to go beyond minimum codes and standards. In addition, U.S. Department of Energy’s successful Commercial Building Partnerships (CBP) program leveraged many of the recommendations from the AEDGs to achieve 50% energy savings over ASHRAE Standard 90.1-2004 for prototypical designs of large commercial entitiesmore » in the retail, banking and lodging sectors. Low-energy technologies and strategies developed during the CBP process have been applied by commercial partners throughout their national portfolio of buildings. Later, the AEDGs served as the perfect platform for both Standard 90.1 and ASHRAE’s high performance buildings standard, Standard 189.1. What was high performance a few years ago, however, has become minimum code today. Indeed, most of the prescriptive envelope component requirements in ASHRAE Standard 90.1-2013 are values recommended in the 50% AEDGs several years ago. Similarly, AEDG strategies and recommendations have penetrated the lighting and HVAC sections of both Standard 189.1 and Standard 90.1. Finally, as we look to the future of codes and standards, the AEDGs are serving as a blueprint for how minimum code requirements could be expressed. By customizing codes to specific building types, design strategies tailored for individual buildings could be prescribed as minimum code, just like in the AEDGs. This paper describes the impact that AEDGs have had over the last decade on the design industry and how they continue to influence the future of codes and Standards. From design professionals to code officials, everyone in the building industry has been affected by the AEDGs.« less

49 CFR 602.15 - Grant requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... either State or locally adopted building codes or standards, the higher of the competing minimums would... title 49, United States Code, as well as cross-cutting requirements, including but not limited to those...

49 CFR 602.15 - Grant requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... either State or locally adopted building codes or standards, the higher of the competing minimums would... title 49, United States Code, as well as cross-cutting requirements, including but not limited to those...

25 CFR 36.104 - What are the requirements for heating, ventilation, cooling and lighting at dormitories?

Code of Federal Regulations, 2013 CFR

2013-04-01

... building codes in the Bureau of Indian Affairs “School Facilities Design Handbook,” dated March 30, 2007... any proposal to change which building codes are included in the Bureau of Indian Affairs “School... inspect the Handbook at the Department of the Interior Library, Main Interior Building, 1849 C Street NW...

25 CFR 36.104 - What are the requirements for heating, ventilation, cooling and lighting at dormitories?

Code of Federal Regulations, 2014 CFR

2014-04-01

... building codes in the Bureau of Indian Affairs “School Facilities Design Handbook,” dated March 30, 2007... any proposal to change which building codes are included in the Bureau of Indian Affairs “School... inspect the Handbook at the Department of the Interior Library, Main Interior Building, 1849 C Street NW...

Performance-based building codes: a call for injury prevention indicators that bridge health and building sectors.

PubMed

Edwards, N

2008-10-01

The international introduction of performance-based building codes calls for a re-examination of indicators used to monitor their implementation. Indicators used in the building sector have a business orientation, target the life cycle of buildings, and guide asset management. In contrast, indicators used in the health sector focus on injury prevention, have a behavioural orientation, lack specificity with respect to features of the built environment, and do not take into account patterns of building use or building longevity. Suggestions for metrics that bridge the building and health sectors are discussed. The need for integrated surveillance systems in health and building sectors is outlined. It is time to reconsider commonly used epidemiological indicators in the field of injury prevention and determine their utility to address the accountability requirements of performance-based codes.

Designing to Meet New Requirements of Differing Services.

ERIC Educational Resources Information Center

Mathers, Andrew S.

1982-01-01

Characterizing "older library buildings" as those built prior to 1960, this article discusses special problems and challenges for the librarian and architect renovator, including building codes and new requirements of differing services. (EJS)

ATLAS software configuration and build tool optimisation

NASA Astrophysics Data System (ADS)

Rybkin, Grigory; Atlas Collaboration

2014-06-01

ATLAS software code base is over 6 million lines organised in about 2000 packages. It makes use of some 100 external software packages, is developed by more than 400 developers and used by more than 2500 physicists from over 200 universities and laboratories in 6 continents. To meet the challenge of configuration and building of this software, the Configuration Management Tool (CMT) is used. CMT expects each package to describe its build targets, build and environment setup parameters, dependencies on other packages in a text file called requirements, and each project (group of packages) to describe its policies and dependencies on other projects in a text project file. Based on the effective set of configuration parameters read from the requirements files of dependent packages and project files, CMT commands build the packages, generate the environment for their use, or query the packages. The main focus was on build time performance that was optimised within several approaches: reduction of the number of reads of requirements files that are now read once per package by a CMT build command that generates cached requirements files for subsequent CMT build commands; introduction of more fine-grained build parallelism at package task level, i.e., dependent applications and libraries are compiled in parallel; code optimisation of CMT commands used for build; introduction of package level build parallelism, i. e., parallelise the build of independent packages. By default, CMT launches NUMBER-OF-PROCESSORS build commands in parallel. The other focus was on CMT commands optimisation in general that made them approximately 2 times faster. CMT can generate a cached requirements file for the environment setup command, which is especially useful for deployment on distributed file systems like AFS or CERN VMFS. The use of parallelism, caching and code optimisation significantly-by several times-reduced software build time, environment setup time, increased the efficiency of multi-core computing resources utilisation, and considerably improved software developer and user experience.

Alternative Formats to Achieve More Efficient Energy Codes for Commercial Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conover, David R.; Rosenberg, Michael I.; Halverson, Mark A.

2013-01-26

This paper identifies and examines several formats or structures that could be used to create the next generation of more efficient energy codes and standards for commercial buildings. Pacific Northwest National Laboratory (PNNL) is funded by the U.S. Department of Energy’s Building Energy Codes Program (BECP) to provide technical support to the development of ANSI/ASHRAE/IES Standard 90.1. While the majority of PNNL’s ASHRAE Standard 90.1 support focuses on developing and evaluating new requirements, a portion of its work involves consideration of the format of energy standards. In its current working plan, the ASHRAE 90.1 committee has approved an energy goalmore » of 50% improvement in Standard 90.1-2013 relative to Standard 90.1-2004, and will likely be considering higher improvement targets for future versions of the standard. To cost-effectively achieve the 50% goal in manner that can gain stakeholder consensus, formats other than prescriptive must be considered. Alternative formats that include reducing the reliance on prescriptive requirements may make it easier to achieve these aggressive efficiency levels in new codes and standards. The focus on energy code and standard formats is meant to explore approaches to presenting the criteria that will foster compliance, enhance verification, and stimulate innovation while saving energy in buildings. New formats may also make it easier for building designers and owners to design and build the levels of efficiency called for in the new codes and standards. This paper examines a number of potential formats and structures, including prescriptive, performance-based (with sub-formats of performance equivalency and performance targets), capacity constraint-based, and outcome-based. The paper also discusses the pros and cons of each format from the viewpoint of code users and of code enforcers.« less

Chapter 8: Fire Performance of Cross-Laminated Timber Assemblies (2012 US Edition)

Treesearch

Christian Dagenais; Robert H. White; Kuma Sumathipala

2012-01-01

Cross-laminated timber (CLT) is a promising wood-based structural component and has potential to provide cost-effective building solutions for residential, commercial and institutional buildings as well as large industrial facilities. Market acceptance of CLT requires that it meets the applicable building code requirements.

Energy Savings Analysis of the Proposed NYStretch-Energy Code 2018

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Bing; Zhang, Jian; Chen, Yan

This study was conducted by the Pacific Northwest National Laboratory (PNNL) in support of the stretch energy code development led by the New York State Energy Research and Development Authority (NYSERDA). In 2017 NYSERDA developed its 2016 Stretch Code Supplement to the 2016 New York State Energy Conservation Construction Code (hereinafter referred to as “NYStretch-Energy”). NYStretch-Energy is intended as a model energy code for statewide voluntary adoption that anticipates other code advancements culminating in the goal of a statewide Net Zero Energy Code by 2028. Since then, NYSERDA continues to develop the NYStretch-Energy Code 2018 edition. To support the effort,more » PNNL conducted energy simulation analysis to quantify the energy savings of proposed commercial provisions of the NYStretch-Energy Code (2018) in New York. The focus of this project is the 20% improvement over existing commercial model energy codes. A key requirement of the proposed stretch code is that it be ‘adoptable’ as an energy code, meaning that it must align with current code scope and limitations, and primarily impact building components that are currently regulated by local building departments. It is largely limited to prescriptive measures, which are what most building departments and design projects are most familiar with. This report describes a set of energy-efficiency measures (EEMs) that demonstrate 20% energy savings over ANSI/ASHRAE/IES Standard 90.1-2013 (ASHRAE 2013) across a broad range of commercial building types and all three climate zones in New York. In collaboration with New Building Institute, the EEMs were developed from national model codes and standards, high-performance building codes and standards, regional energy codes, and measures being proposed as part of the on-going code development process. PNNL analyzed these measures using whole building energy models for selected prototype commercial buildings and multifamily buildings representing buildings in New York. Section 2 of this report describes the analysis methodology, including the building types and construction area weights update for this analysis, the baseline, and the method to conduct the energy saving analysis. Section 3 provides detailed specifications of the EEMs and bundles. Section 4 summarizes the results of individual EEMs and EEM bundles by building type, energy end-use and climate zone. Appendix A documents detailed descriptions of the selected prototype buildings. Appendix B provides energy end-use breakdown results by building type for both the baseline code and stretch code in all climate zones.« less

New Whole-House Solutions Case Study: Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings, Upstate New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-11-01

While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient; the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-rise multifamily dwellings. While thismore » air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of Building America team Consortium for Advanced Residential Building's (CARB) multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in three multifamily buildings.« less

Monitor Network Traffic with Packet Capture (pcap) on an Android Device

DTIC Science & Technology

2015-09-01

administrative privileges . Under the current design Android development requirement, an Android Graphical User Interface (GUI) application cannot directly...build an Android application to monitor network traffic using open source packet capture (pcap) libraries. 15. SUBJECT TERMS ELIDe, Android , pcap 16...Building Application with Native Codes 5 8.1 Calling Native Codes Using JNI 5 8.2 Calling Native Codes from an Android Application 8 9. Retrieve Live

Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klocke, S.; Faakye, O.; Puttagunta, S.

2014-10-01

While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient by itself. In addition, the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-risemore » multifamily dwellings. While this air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of Consortium for Advanced Residential Building's (CARB’s) multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in 3 multifamily buildings.« less

Building America Case Study: Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings, Upstate New York (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-11-01

While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient by itself. In addition, the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-risemore » multifamily dwellings. While this air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of CARB's multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in 3 multifamily buildings.« less

Probabilistic Seismic Hazard Assessment for Iraq

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onur, Tuna; Gok, Rengin; Abdulnaby, Wathiq

Probabilistic Seismic Hazard Assessments (PSHA) form the basis for most contemporary seismic provisions in building codes around the world. The current building code of Iraq was published in 1997. An update to this edition is in the process of being released. However, there are no national PSHA studies in Iraq for the new building code to refer to for seismic loading in terms of spectral accelerations. As an interim solution, the new draft building code was considering to refer to PSHA results produced in the late 1990s as part of the Global Seismic Hazard Assessment Program (GSHAP; Giardini et al.,more » 1999). However these results are: a) more than 15 years outdated, b) PGA-based only, necessitating rough conversion factors to calculate spectral accelerations at 0.3s and 1.0s for seismic design, and c) at a probability level of 10% chance of exceedance in 50 years, not the 2% that the building code requires. Hence there is a pressing need for a new, updated PSHA for Iraq.« less

Study of structural reliability of existing concrete structures

NASA Astrophysics Data System (ADS)

Druķis, P.; Gaile, L.; Valtere, K.; Pakrastiņš, L.; Goremikins, V.

2017-10-01

Structural reliability of buildings has become an important issue after the collapse of a shopping center in Riga 21.11.2013, caused the death of 54 people. The reliability of a building is the practice of designing, constructing, operating, maintaining and removing buildings in ways that ensure maintained health, ward suffered injuries or death due to use of the building. Evaluation and improvement of existing buildings is becoming more and more important. For a large part of existing buildings, the design life has been reached or will be reached in the near future. The structures of these buildings need to be reassessed in order to find out whether the safety requirements are met. The safety requirements provided by the Eurocodes are a starting point for the assessment of safety. However, it would be uneconomical to require all existing buildings and structures to comply fully with these new codes and corresponding safety levels, therefore the assessment of existing buildings differs with each design situation. This case study describes the simple and practical procedure of determination of minimal reliability index β of existing concrete structures designed by different codes than Eurocodes and allows to reassess the actual reliability level of different structural elements of existing buildings under design load.

36 CFR 1234.20 - What rules apply if there is a conflict between NARA standards and other regulatory standards...

Code of Federal Regulations, 2014 CFR

2014-07-01

... regional building codes, the following rules of precedence apply: (1) Between differing levels of fire... cannot be reconciled with a requirement of this part, the local or regional code applies. (b) If any of... require documentation of the mandatory nature of the conflicting code and the inability to reconcile that...

36 CFR 1234.20 - What rules apply if there is a conflict between NARA standards and other regulatory standards...

Code of Federal Regulations, 2012 CFR

2012-07-01

... regional building codes, the following rules of precedence apply: (1) Between differing levels of fire... cannot be reconciled with a requirement of this part, the local or regional code applies. (b) If any of... require documentation of the mandatory nature of the conflicting code and the inability to reconcile that...

36 CFR 1234.20 - What rules apply if there is a conflict between NARA standards and other regulatory standards...

Code of Federal Regulations, 2011 CFR

2011-07-01

... regional building codes, the following rules of precedence apply: (1) Between differing levels of fire... cannot be reconciled with a requirement of this part, the local or regional code applies. (b) If any of... require documentation of the mandatory nature of the conflicting code and the inability to reconcile that...

36 CFR § 1234.20 - What rules apply if there is a conflict between NARA standards and other regulatory standards...

Code of Federal Regulations, 2013 CFR

2013-07-01

... regional building codes, the following rules of precedence apply: (1) Between differing levels of fire... cannot be reconciled with a requirement of this part, the local or regional code applies. (b) If any of... require documentation of the mandatory nature of the conflicting code and the inability to reconcile that...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2012 CFR

2012-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2014 CFR

2014-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2011 CFR

2011-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2013 CFR

2013-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

24 CFR 983.155 - Completion of housing.

Code of Federal Regulations, 2010 CFR

2010-04-01

... with local requirements (such as code and zoning requirements); and (ii) An architect's certification that the housing complies with: (A) HUD housing quality standards; (B) State, local, or other building codes; (C) Zoning; (D) The rehabilitation work write-up (for rehabilitated housing) or the work...

44 CFR 206.400 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

... standards of safety, decency, and sanitation and in conformity with applicable codes, specifications and standards. (b) Applicable codes, specifications, and standards shall include any disaster resistant building code that meets the minimum requirements of the National Flood Insurance Program (NFIP) as well as...

44 CFR 206.400 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... standards of safety, decency, and sanitation and in conformity with applicable codes, specifications and standards. (b) Applicable codes, specifications, and standards shall include any disaster resistant building code that meets the minimum requirements of the National Flood Insurance Program (NFIP) as well as...

44 CFR 206.400 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... standards of safety, decency, and sanitation and in conformity with applicable codes, specifications and standards. (b) Applicable codes, specifications, and standards shall include any disaster resistant building code that meets the minimum requirements of the National Flood Insurance Program (NFIP) as well as...

44 CFR 206.400 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... standards of safety, decency, and sanitation and in conformity with applicable codes, specifications and standards. (b) Applicable codes, specifications, and standards shall include any disaster resistant building code that meets the minimum requirements of the National Flood Insurance Program (NFIP) as well as...

44 CFR 206.400 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... standards of safety, decency, and sanitation and in conformity with applicable codes, specifications and standards. (b) Applicable codes, specifications, and standards shall include any disaster resistant building code that meets the minimum requirements of the National Flood Insurance Program (NFIP) as well as...

24 CFR 242.78 - Zoning, deed, and building restrictions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Zoning, deed, and building... AUTHORITIES MORTGAGE INSURANCE FOR HOSPITALS Miscellaneous Requirements § 242.78 Zoning, deed, and building... to the project site, and shall comply with all applicable building and other governmental codes...

Common Day Care Safety Renovations: Descriptions, Explanations and Cost Estimates.

ERIC Educational Resources Information Center

Spack, Stan

This booklet explains some of the day care safety features specified by the new Massachusetts State Building Code (January 1, 1975) which must be met before a new day care center can be licensed. The safety features described are those which most often require renovation to meet the building code standards. Best estimates of the costs involved in…

Revision of seismic design codes corresponding to building damages in the ``5.12'' Wenchuan earthquake

NASA Astrophysics Data System (ADS)

Wang, Yayong

2010-06-01

A large number of buildings were seriously damaged or collapsed in the “5.12” Wenchuan earthquake. Based on field surveys and studies of damage to different types of buildings, seismic design codes have been updated. This paper briefly summarizes some of the major revisions that have been incorporated into the “Standard for classification of seismic protection of building constructions GB50223-2008” and “Code for Seismic Design of Buildings GB50011-2001.” The definition of seismic fortification class for buildings has been revisited, and as a result, the seismic classifications for schools, hospitals and other buildings that hold large populations such as evacuation shelters and information centers have been upgraded in the GB50223-2008 Code. The main aspects of the revised GB50011-2001 code include: (a) modification of the seismic intensity specified for the Provinces of Sichuan, Shanxi and Gansu; (b) basic conceptual design for retaining walls and building foundations in mountainous areas; (c) regularity of building configuration; (d) integration of masonry structures and pre-cast RC floors; (e) requirements for calculating and detailing stair shafts; and (f) limiting the use of single-bay RC frame structures. Some significant examples of damage in the epicenter areas are provided as a reference in the discussion on the consequences of collapse, the importance of duplicate structural systems, and the integration of RC and masonry structures.

75 FR 14331 - Disaster Assistance Loan Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-25

... meet current building code requirements. If your business is a major source of employment, SBA may..., granting tax exemption under sections 510(c), (d), or (e) of the Internal Revenue Code of 1954, or (2...; 8:45 am] BILLING CODE 8025-01-P ...

Residential photovoltaic module and array requirements study, appendices

NASA Technical Reports Server (NTRS)

Nearhoof, S. L.; Oster, J. R.

1979-01-01

Regional building code variations, federal and city codes, and the national electric code are reviewed for their possible effects on the design of photovoltaic modules. Problems that photovoltaic arrays may impose on the insurability of residences are also discussed. Mounting configurations are developed for the modules, and grounding, wiring, terminal, and voltage requirements are established. Installation and materials costs are presented along with performance criteria.

Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klocke, S.; Faakye, O.; Puttagunta, S.

2014-10-01

​While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient by itself. In addition, the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-risemore » multifamily dwellings. While this air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of CARB's multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in 3 multifamily buildings.« less

Developing Performance Cost Index Targets for ASHRAE Standard 90.1 Appendix G – Performance Rating Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, Michael I.; Hart, Philip R.

2016-02-16

Appendix G, the Performance Rating Method in ASHRAE Standard 90.1 has been updated to make two significant changes for the 2016 edition, to be published in October of 2016. First, it allows Appendix G to be used as a third path for compliance with the standard in addition to rating beyond code building performance. This prevents modelers from having to develop separate building models for code compliance and beyond code programs. Using this new version of Appendix G to show compliance with the 2016 edition of the standard, the proposed building design needs to have a performance cost index (PCI)more » less than targets shown in a new table based on building type and climate zone. The second change is that the baseline design is now fixed at a stable level of performance set approximately equal to the 2004 code. Rather than changing the stringency of the baseline with each subsequent edition of the standard, compliance with new editions will simply require a reduced PCI (a PCI of zero is a net-zero building). Using this approach, buildings of any era can be rated using the same method. The intent is that any building energy code or beyond code program can use this methodology and merely set the appropriate PCI target for their needs. This report discusses the process used to set performance criteria for compliance with ASHRAE Standard 90.1-2016 and suggests a method for demonstrating compliance with other codes and beyond code programs.« less

Developing Performance Cost Index Targets for ASHRAE Standard 90.1 Appendix G – Performance Rating Method - Rev.1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, Michael I.; Hart, Philip R.

2016-03-01

Appendix G, the Performance Rating Method in ASHRAE Standard 90.1 has been updated to make two significant changes for the 2016 edition, to be published in October of 2016. First, it allows Appendix G to be used as a third path for compliance with the standard in addition to rating beyond code building performance. This prevents modelers from having to develop separate building models for code compliance and beyond code programs. Using this new version of Appendix G to show compliance with the 2016 edition of the standard, the proposed building design needs to have a performance cost index (PCI)more » less than targets shown in a new table based on building type and climate zone. The second change is that the baseline design is now fixed at a stable level of performance set approximately equal to the 2004 code. Rather than changing the stringency of the baseline with each subsequent edition of the standard, compliance with new editions will simply require a reduced PCI (a PCI of zero is a net-zero building). Using this approach, buildings of any era can be rated using the same method. The intent is that any building energy code or beyond code program can use this methodology and merely set the appropriate PCI target for their needs. This report discusses the process used to set performance criteria for compliance with ASHRAE Standard 90.1-2016 and suggests a method for demonstrating compliance with other codes and beyond code programs.« less

47 CFR 87.199 - Special requirements for 406.0-406.1 MHz ELTs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... identification code, issued by the National Oceanic and Atmospheric Administration (NOAA), the United States... code addressed to: NOAA/SARSAT Beacon Registration, E/SP3, Federal Building 4, Room 3320, 5200 Auth..., type of aircraft, alternate emergency contact, and other information as required by NOAA. The...

47 CFR 87.199 - Special requirements for 406.0-406.1 MHz ELTs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... identification code, issued by the National Oceanic and Atmospheric Administration (NOAA), the United States... code addressed to: NOAA/SARSAT Beacon Registration, E/SP3, Federal Building 4, Room 3320, 5200 Auth..., type of aircraft, alternate emergency contact, and other information as required by NOAA. The...

Structural evaluation of the 2736Z Building for seismic loads

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giller, R.A.

The 2736Z building structure is evaluated for high-hazard loads. The 2736Z building is analyzed herein for normal and seismic loads and is found to successfully meet the guidelines of UCRL-15910 along with the related codes requirements.

28 CFR 36.602 - General rule.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.602 General... that a code meets or exceeds the minimum requirements of the Act for the accessibility and usability of...

28 CFR 36.602 - General rule.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.602 General... that a code meets or exceeds the minimum requirements of the Act for the accessibility and usability of...

28 CFR 36.602 - General rule.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.602 General... that a code meets or exceeds the minimum requirements of the Act for the accessibility and usability of...

28 CFR 36.602 - General rule.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.602 General... that a code meets or exceeds the minimum requirements of the Act for the accessibility and usability of...

28 CFR 36.602 - General rule.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.602 General... that a code meets or exceeds the minimum requirements of the Act for the accessibility and usability of...

Jackson Park Hospital Green Building Medical Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

William Dorsey; Nelson Vasquez

2010-03-31

Jackson Park Hospital completed the construction of a new Medical Office Building on its campus this spring. The new building construction has adopted the City of Chicago's recent focus on protecting the environment, and conserving energy and resources, with the introduction of green building codes. Located in a poor, inner city neighborhood on the South side of Chicago, Jackson Park Hospital has chosen green building strategies to help make the area a better place to live and work. The new green building houses the hospital's Family Medicine Residency Program and Specialty Medical Offices. The residency program has been vital inmore » attracting new, young physicians to this medically underserved area. The new outpatient center will also help to allure needed medical providers to the community. The facility also has areas designated to women's health and community education. The Community Education Conference Room will provide learning opportunities to area residents. Emphasis will be placed on conserving resources and protecting our environment, as well as providing information on healthcare access and preventive medicine. The new Medical Office Building was constructed with numerous energy saving features. The exterior cladding of the building is an innovative, locally-manufactured precast concrete panel system with integral insulation that achieves an R-value in excess of building code requirements. The roof is a 'green roof' covered by native plantings, lessening the impact solar heat gain on the building, and reducing air conditioning requirements. The windows are low-E, tinted, and insulated to reduce cooling requirements in summer and heating requirements in winter. The main entrance has an air lock to prevent unconditioned air from entering the building and impacting interior air temperatures. Since much of the traffic in and out of the office building comes from the adjacent Jackson Park Hospital, a pedestrian bridge connects the two buildings, further decreasing the amount of unconditioned air that enters the office building. The HVAC system has an Energy Efficiency Rating 29% greater than required. No CFC based refrigerants were used in the HVAC system, thus reducing the emission of compounds that contribute to ozone depletion and global warming. In addition, interior light fixtures employ the latest energy-efficient lamp and ballast technology. Interior lighting throughout the building is operated by sensors that will automatically turn off lights inside a room when the room is unoccupied. The electrical traction elevators use less energy than typical elevators, and they are made of 95% recycled material. Further, locally manufactured products were used throughout, minimizing the amount of energy required to construct this building. The primary objective was to construct a 30,000 square foot medical office building on the Jackson Park Hospital campus that would comply with newly adopted City of Chicago green building codes focusing on protecting the environment and conserving energy and resources. The energy saving systems demonstrate a state of the-art whole-building approach to energy efficient design and construction. The energy efficiency and green aspects of the building contribute to the community by emphasizing the environmental and economic benefits of conserving resources. The building highlights the integration of Chicago's new green building codes into a poor, inner city neighborhood project and it is designed to attract medical providers and physicians to a medically underserved area.« less

Fire safety

Treesearch

Robert H. White; Mark A. Dietenberger

1999-01-01

Fire safety is an important concern in all types of construction. The high level of national concern for fire safety is reflected in limitations and design requirements in building codes. These code requirements are discussed in the context of fire safety design and evaluation in the initial section of this chapter. Since basic data on fire behavior of wood products...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaufmann, John R.; Hand, James R.; Halverson, Mark A.

This report evaluates how and when to best integrate renewable energy requirements into building energy codes. The basic goals were to: (1) provide a rough guide of where we’re going and how to get there; (2) identify key issues that need to be considered, including a discussion of various options with pros and cons, to help inform code deliberations; and (3) to help foster alignment among energy code-development organizations. The authors researched current approaches nationally and internationally, conducted a survey of key stakeholders to solicit input on various approaches, and evaluated the key issues related to integration of renewable energymore » requirements and various options to address those issues. The report concludes with recommendations and a plan to engage stakeholders. This report does not evaluate whether the use of renewable energy should be required on buildings; that question involves a political decision that is beyond the scope of this report.« less

How to Build MCNP 6.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bull, Jeffrey S.

This presentation describes how to build MCNP 6.2. MCNP®* 6.2 can be compiled on Macs, PCs, and most Linux systems. It can also be built for parallel execution using both OpenMP and Messing Passing Interface (MPI) methods. MCNP6 requires Fortran, C, and C++ compilers to build the code.

Fire safety of wood construction

Treesearch

Robert H. White; Mark A. Dietenberger

2010-01-01

Fire safety is an important concern in all types of construction. The high level of national concern for fire safety is reflected in limitations and design requirements in building codes. These code requirements and related fire performance data are discussed in the context of fire safety design and evaluation in the initial section of this chapter. Because basic data...

Survey of existing performance requirements in codes and standards for light-frame construction

Treesearch

G. E. Sherwood

1980-01-01

Present building codes and standards are a combination of specifications and performance criteria. Where specifications prevail, the introduction f new materials or methods can be a long, cumbersome process. To facilitate the introduction of new technology, performance requirements are becoming more prevalent. In some areas, there is a lack of information on which to...

78 FR 8448 - Streamlining Inspection and Warranty Requirements for Federal Housing Administration (FHA) Single...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-06

... jurisdiction did not already perform its own inspections for new construction, and issue building permits and... expected to be minimal. The increased quality of construction materials and the standardization of building... governments that have adopted building codes to regulate and standardize the construction of residential and...

Building America Top Innovations 2012: Building Science-Based Climate Maps

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-01-01

This Building America Top Innovations profile describes the Building America-developed climate zone map, which serves as a consistent framework for energy-efficiency requirements in the national model energy code starting with the 2004 IECC Supplement and the ASHRAE 90.1 2004 edition. The map also provides a critical foundation for climate-specific guidance in the widely disseminated EEBA Builder Guides and Building America Best Practice Guides.

The development of fire evaluation system for detention and correctional occupancies

NASA Astrophysics Data System (ADS)

Nelson, H. E.; Shibe, A. J.

1984-12-01

A fire safety evaluation system for detention and correctional occupancies was developed. It can be used for determining if a facility has fire safety equivalent to that obtained by meeting the requirement of a given code. The system was calibrated for use with proposed chapters for detention and correctional occupancies of the Life Safety Code (1985). There are separate sets of requirements for each of four use conditions: one for zoned egress, one for zoned impeded egress, one for impeded egress, and one for contained. Within each set, there are two levels of evaluation: one for partially sprinklered and nonsprinklered buildings, and one for totally sprinklered buildings.

Energy Codes at a Glance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, Pamala C.; Richman, Eric E.

2008-09-01

Feeling dim from energy code confusion? Read on to give your inspections a charge. The U.S. Department of Energy’s Building Energy Codes Program addresses hundreds of inquiries from the energy codes community every year. This article offers clarification for topics of confusion submitted to BECP Technical Support of interest to electrical inspectors, focusing on the residential and commercial energy code requirements based on the most recently published 2006 International Energy Conservation Code® and ANSI/ASHRAE/IESNA1 Standard 90.1-2004.

Analysis of IECC (2003, 2006, 2009) and ASHRAE 90.1-2007 Commercial Energy Code Requirements for Mesa, AZ.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Yunzhi; Gowri, Krishnan

2011-02-28

This report summarizes code requirements and energy savings of commercial buildings in Climate Zone 2B built to the 2009 IECC and ASHRAE Standard 90.1-2007 when compared to the 2003 IECC and the 2006 IECC. In general, the 2009 IECC and ASHRAE Standard 90.1-2007 have higher insulation requirements for exterior walls, roof, and windows and have higher efficiency requirements for HVAC equipment. HVAC equipment efficiency requirements are governed by National Appliance Conversion Act of 1987 (NAECA), and are applicable irrespective of the IECC version adopted. The energy analysis results show that commercial buildings meeting the 2009 IECC requirements save 4.4% tomore » 9.5% site energy and 4.1% to 9.9% energy cost when compared to the 2006 IECC; and save 10.6% to 29.4% site energy and 10.3% to 29.3% energy cost when compared to the 2003 IECC. Similar analysis comparing ASHRAE Standard 90.1-2007 requirements to the 2006 IECC shows that the energy savings are in the 4.0% to 10.7% for multi-family and retail buildings, but less than 2% for office buildings. Further comparison of ASHRAE Standard 90.1-2007 requirements to the 2003 IECC show site energy savings in the range of 7.7% to 30.6% and energy cost savings range from 7.9% to 30.3%. Both the 2009 IECC and ASHRAE Standard 90.1-2007 have the potential to save energy by comparable levels for most building types.« less

Building an ontology of pulmonary diseases with natural language processing tools using textual corpora.

PubMed

Baneyx, Audrey; Charlet, Jean; Jaulent, Marie-Christine

2007-01-01

Pathologies and acts are classified in thesauri to help physicians to code their activity. In practice, the use of thesauri is not sufficient to reduce variability in coding and thesauri are not suitable for computer processing. We think the automation of the coding task requires a conceptual modeling of medical items: an ontology. Our task is to help lung specialists code acts and diagnoses with software that represents medical knowledge of this concerned specialty by an ontology. The objective of the reported work was to build an ontology of pulmonary diseases dedicated to the coding process. To carry out this objective, we develop a precise methodological process for the knowledge engineer in order to build various types of medical ontologies. This process is based on the need to express precisely in natural language the meaning of each concept using differential semantics principles. A differential ontology is a hierarchy of concepts and relationships organized according to their similarities and differences. Our main research hypothesis is to apply natural language processing tools to corpora to develop the resources needed to build the ontology. We consider two corpora, one composed of patient discharge summaries and the other being a teaching book. We propose to combine two approaches to enrich the ontology building: (i) a method which consists of building terminological resources through distributional analysis and (ii) a method based on the observation of corpus sequences in order to reveal semantic relationships. Our ontology currently includes 1550 concepts and the software implementing the coding process is still under development. Results show that the proposed approach is operational and indicates that the combination of these methods and the comparison of the resulting terminological structures give interesting clues to a knowledge engineer for the building of an ontology.

7 CFR 4274.337 - Other regulatory requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

....337 Agriculture Regulations of the Department of Agriculture (Continued) RURAL BUSINESS-COOPERATIVE... recipient on the basis of sex, marital status, race, color, religion, national origin, age, physical or... of one of the following model building codes or the latest edition of that code providing an...

Effects from the Reduction of Air Leakage on Energy and Durability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hun, Diana E.; Childs, Phillip W.; Atchley, Jerald Allen

2014-01-01

Buildings are responsible for approximately 40% of the energy used in the US. Codes have been increasing building envelope requirements, and in particular those related to improving airtightness, in order to reduce energy consumption. The main goal of this research was to evaluate the effects from reductions in air leakage on energy loads and material durability. To this end, we focused on the airtightness and thermal resistance criteria set by the 2012 International Energy Conservation Code (IECC).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Evans, Meredydd; Shi, Qing

China will account for about half of the new construction globally in the coming decade. Its floorspace doubled from 1996 to 2011, and Chinese rural buildings alone have as much floorspace as all of U.S. residential buildings. Building energy consumption has also grown, increasing by over 40% since 1990. To curb building energy demand, the Chinese government has launched a series of policies and programs. Combined, this growth in buildings and renovations, along with the policies to promote green buildings, are creating a large market for energy efficiency products and services. This report assesses the impact of China’s policies onmore » building energy efficiency and on the market for energy efficiency in the future. The first chapter of this report introduces the trends in China, drawing on both historical analysis, and detailed modeling of the drivers behind changes in floorspace and building energy demand such as economic and population growth, urbanization, policy. The analysis describes the trends by region, building type and energy service. The second chapter discusses China’s policies to promote green buildings. China began developing building energy codes in the 1980s. Over time, the central government has increased the stringency of the code requirements and the extent of enforcement. The codes are mandatory in all new buildings and major renovations in China’s cities, and they have been a driving force behind the expansion of China’s markets for insulation, efficient windows, and other green building materials. China also has several other important policies to encourage efficient buildings, including the Three-Star Rating System (somewhat akin to LEED), financial incentives tied to efficiency, appliance standards, a phasing out of incandescent bulbs and promotion of efficient lighting, and several policies to encourage retrofits in existing buildings. In the third chapter, we take “deep dives” into the trends affecting key building components. This chapter examines insulation in walls and roofs; efficient windows and doors; heating, air conditioning and controls; and lighting. These markets have seen significant growth because of the strength of the construction sector but also the specific policies that require and promote efficient building components. At the same time, as requirements have become more stringent, there has been fierce competition, and quality has at time suffered, which in turn has created additional challenges. Next we examine existing buildings in chapter four. China has many Soviet-style, inefficient buildings built before stringent requirements for efficiency were more widely enforced. As a result, there are several specific market opportunities related to retrofits. These fall into two or three categories. First, China now has a code for retrofitting residential buildings in the north. Local governments have targets of the number of buildings they must retrofit each year, and they help finance the changes. The requirements focus on insulation, windows, and heat distribution. Second, the Chinese government recently decided to increase the scale of its retrofits of government and state-owned buildings. It hopes to achieve large scale changes through energy service contracts, which creates an opportunity for energy service companies. Third, there is also a small but growing trend to apply energy service contracts to large commercial and residential buildings. This report assesses the impacts of China’s policies on building energy efficiency. By examining the existing literature and interviewing stakeholders from the public, academic, and private sectors, the report seeks to offer an in-depth insights of the opportunities and barriers for major market segments related to building energy efficiency. The report also discusses trends in building energy use, policies promoting building energy efficiency, and energy performance contracting for public building retrofits.« less

An international survey of building energy codes and their implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Meredydd; Roshchanka, Volha; Graham, Peter

Buildings are key to low-carbon development everywhere, and many countries have introduced building energy codes to improve energy efficiency in buildings. Yet, building energy codes can only deliver results when the codes are implemented. For this reason, studies of building energy codes need to consider implementation of building energy codes in a consistent and comprehensive way. This research identifies elements and practices in implementing building energy codes, covering codes in 22 countries that account for 70% of global energy demand from buildings. Access to benefits of building energy codes depends on comprehensive coverage of buildings by type, age, size, andmore » geographic location; an implementation framework that involves a certified agency to inspect construction at critical stages; and independently tested, rated, and labeled building energy materials. Training and supporting tools are another element of successful code implementation, and their role is growing in importance, given the increasing flexibility and complexity of building energy codes. Some countries have also introduced compliance evaluation and compliance checking protocols to improve implementation. This article provides examples of practices that countries have adopted to assist with implementation of building energy codes.« less

To amend title 40, United States Code, to require that restrooms in public buildings be equipped with baby changing facilities.

THOMAS, 111th Congress

Rep. Kildee, Dale E. [D-MI-5

2010-01-27

House - 01/28/2010 Referred to the Subcommittee on Economic Development, Public Buildings and Emergency Management. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Joint China-United States Report for Year 1 Insulation Materials and Systems Project Area Clean Energy Research Center Building Energy Efficiency (CERC-BEE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, Therese K; Biswas, Kaushik; Song, Bo

In November of 2009, the presidents of China and the U.S. announced the establishment of the Clean Energy Research Center (CERC). This broad research effort is co-funded by both countries and involves a large number of research centers and universities in both countries. One part of this program is focused on improving the energy efficiency of buildings. One portion of the CERC-BEE was focused on building insulation systems. The research objective of this effort was to Identify and investigate candidate high performance fire resistant building insulation technologies that meet the goal of building code compliance for exterior wall applications inmore » green buildings in multiple climate zones. A Joint Work Plan was established between researchers at the China Academy of Building Research and Oak Ridge National Laboratory. Efforts in the first year under this plan focused on information gathering. The objective of this research program is to reduce building energy use in China via improved building insulation technology. In cold regions in China, residents often use inefficient heating systems to provide a minimal comfort level within inefficient buildings. In warmer regions, air conditioning has not been commonly used. As living standards rise, energy consumption in these regions will increase dramatically unless significant improvements are made in building energy performance. Previous efforts that defined the current state of the built environment in China and in the U.S. will be used in this research. In countries around the world, building improvements have typically followed the implementation of more stringent building codes. There have been several changes in building codes in both the U.S. and China within the last few years. New U.S. building codes have increased the amount of wall insulation required in new buildings. New government statements from multiple agencies in China have recently changed the requirements for buildings in terms of energy efficiency and fire safety. A related issue is the degree to which new standards are adopted and enforced. In the U.S., standards are developed using a consensus process, and local government agencies are free to implement these standards or to ignore them. For example, some U.S. states are still using 2003 versions of the building efficiency standards. There is also a great variation in the degree to which the locally adopted standards are enforced in different U.S. cities and states. With a more central process in China, these issues are different, but possible impacts of variable enforcement efficacy may also exist. Therefore, current building codes in China will be compared to the current state of building fire-safety and energy-efficiency codes in the U.S. and areas for possible improvements in both countries will be explored. In particular, the focus of the applications in China will be on green buildings. The terminology of 'green buildings' has different meanings to different audiences. The U.S. research is interested in both new, green buildings, and on retrofitting existing inefficient buildings. An initial effort will be made to clarify the scope of the pertinent wall insulation systems for these applications.« less

Analysis of Design-Build Processes, Best Practices, and Applications to the Department of Defense

DTIC Science & Technology

2006-06-01

NAVFAC design-build processes published in trade journals, books , magazines, internet articles, and DoD policy. In their book , Contract Management...literature review concentrates on recent articles published in books , trade magazines, and on the internet to determine design-build processes and...Keith Molenaar ) Design-build projects under the State of California’s Public Contract Code (Legaltips.org, 2006) requires the owner, for example the

Building code compliance and enforcement: The experience of San Francisco's residential energy conservation ordinance and California's building standards for new construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vine, E.

1990-11-01

As part of Lawrence Berkeley Laboratory's (LBL) technical assistance to the Sustainable City Project, compliance and enforcement activities related to local and state building codes for existing and new construction were evaluated in two case studies. The analysis of the City of San Francisco's Residential Energy Conservation Ordinance (RECO) showed that a limited, prescriptive energy conservation ordinance for existing residential construction can be enforced relatively easily with little administrative costs, and that compliance with such ordinances can be quite high. Compliance with the code was facilitated by extensive publicity, an informed public concerned with the cost of energy and knowledgeablemore » about energy efficiency, the threat of punishment (Order of Abatement), the use of private inspectors, and training workshops for City and private inspectors. The analysis of California's Title 24 Standards for new residential and commercial construction showed that enforcement of this type of code for many climate zones is more complex and requires extensive administrative support for education and training of inspectors, architects, engineers, and builders. Under this code, prescriptive and performance approaches for compliance are permitted, resulting in the demand for alternative methods of enforcement: technical assistance, plan review, field inspection, and computer analysis. In contrast to existing to construction, building design and new materials and construction practices are of critical importance in new construction, creating a need for extensive technical assistance and extensive interaction between enforcement personnel and the building community. Compliance problems associated with building design and installation did occur in both residential and nonresidential buildings. 12 refs., 5 tabs.« less

Fire related hazards of cables: The Canadian position development of fire resistant inside wiring cable

NASA Astrophysics Data System (ADS)

Hartley, M. D.; Jaques, R. E.

1986-11-01

The Canadian Electrical Code and the National Building Code in Canada recognize only two designations in regards to fire resistance of cables; cables for use in combustible (residential) buildings and cables for use in non-combustible buildings. The Test standard for cables for non-combustible buildings resembles IEEE-383. However, it is more severe; particularly for small nonarmoured cables such as Inside Wiring Cable. This forthcoming requirement has necessitated material and product development. Although an Inside Wiring cable modification of both insulation and jacket was undertaken, the large volume fraction of combustible material in the jacket vis a vis the insulation made it the area of greatest impact. The paper outlines the development and its effect on cable performance.

Country Report on Building Energy Codes in Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shui, Bin; Evans, Meredydd; Somasundaram, Sriram

2009-04-02

This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in Australia, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, and lighting) for commercial and residential buildings in Australia.

Assessment of the Potential to Achieve very Low Energy Use in Public Buildings in China with Advanced Window and Shading Systems

DOE PAGES

Lee, Eleanor; Pang, Xiufeng; McNeil, Andrew; ...

2015-05-29

Here, as rapid growth in the construction industry continues to occur in China, the increased demand for a higher standard living is driving significant growth in energy use and demand across the country. Building codes and standards have been implemented to head off this trend, tightening prescriptive requirements for fenestration component measures using methods similar to the US model energy code American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) 90.1. The objective of this study is to (a) provide an overview of applicable code requirements and current efforts within China to enable characterization and comparison of window and shadingmore » products, and (b) quantify the load reduction and energy savings potential of several key advanced window and shading systems, given the divergent views on how space conditioning requirements will be met in the future. System-level heating and cooling loads and energy use performance were evaluated for a code-compliant large office building using the EnergyPlus building energy simulation program. Commercially-available, highly-insulating, low-emittance windows were found to produce 24-66% lower perimeter zone HVAC electricity use compared to the mandated energy-efficiency standard in force (GB 50189-2005) in cold climates like Beijing. Low-e windows with operable exterior shading produced up to 30-80% reductions in perimeter zone HVAC electricity use in Beijing and 18-38% reductions in Shanghai compared to the standard. The economic context of China is unique since the cost of labor and materials for the building industry is so low. Broad deployment of these commercially available technologies with the proper supporting infrastructure for design, specification, and verification in the field would enable significant reductions in energy use and greenhouse gas emissions in the near term.« less

Assessment of the Potential to Achieve very Low Energy Use in Public Buildings in China with Advanced Window and Shading Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Eleanor; Pang, Xiufeng; McNeil, Andrew

Here, as rapid growth in the construction industry continues to occur in China, the increased demand for a higher standard living is driving significant growth in energy use and demand across the country. Building codes and standards have been implemented to head off this trend, tightening prescriptive requirements for fenestration component measures using methods similar to the US model energy code American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) 90.1. The objective of this study is to (a) provide an overview of applicable code requirements and current efforts within China to enable characterization and comparison of window and shadingmore » products, and (b) quantify the load reduction and energy savings potential of several key advanced window and shading systems, given the divergent views on how space conditioning requirements will be met in the future. System-level heating and cooling loads and energy use performance were evaluated for a code-compliant large office building using the EnergyPlus building energy simulation program. Commercially-available, highly-insulating, low-emittance windows were found to produce 24-66% lower perimeter zone HVAC electricity use compared to the mandated energy-efficiency standard in force (GB 50189-2005) in cold climates like Beijing. Low-e windows with operable exterior shading produced up to 30-80% reductions in perimeter zone HVAC electricity use in Beijing and 18-38% reductions in Shanghai compared to the standard. The economic context of China is unique since the cost of labor and materials for the building industry is so low. Broad deployment of these commercially available technologies with the proper supporting infrastructure for design, specification, and verification in the field would enable significant reductions in energy use and greenhouse gas emissions in the near term.« less

Ethical Guidelines for Structural Interventions to Small-Scale Historic Stone Masonry Buildings.

PubMed

Hurol, Yonca; Yüceer, Hülya; Başarır, Hacer

2015-12-01

Structural interventions to historic stone masonry buildings require that both structural and heritage values be considered simultaneously. The absence of one of these value systems in implementation can be regarded as an unethical professional action. The research objective of this article is to prepare a guideline for ensuring ethical structural interventions to small-scale stone historic masonry buildings in the conservation areas of Northern Cyprus. The methodology covers an analysis of internationally accepted conservation documents and national laws related to the conservation of historic buildings, an analysis of building codes, especially Turkish building codes, which have been used in Northern Cyprus, and an analysis of the structural interventions introduced to a significant historic building in a semi-intact state in the walled city of Famagusta. This guideline covers issues related to whether buildings are intact or ruined, the presence of earthquake risk, the types of structural decisions in an architectural conservation project, and the values to consider during the decision making phase.

75 FR 54131 - Updating State Residential Building Energy Efficiency Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-03

... and 95 degrees F for heating (for heat pumps), the 2000 IECC insulation requirement for supply ducts in unconditioned spaces is R-5 (minimum) for nearly all cases. Insulation required by the 2000 IECC... Duct Insulation Requirements Duct insulation requirements generally increased in the 2003 IECC. The...

Universal Design as a Booster for Housing Quality and Architectural Practice.

PubMed

Denizou, Karine

2016-01-01

Norwegian central government has for the last decade increasingly focused on universal design. Fundamental changes in the Norwegian building code and corresponding regulations in 2010 give an apparently clear framework for the implementation of accessibility and universal design. However, it seems that neither increased awareness of accessibility requirements and universal design, nor compliance with the building code guarantees improvement of housing quality and usability. The Norwegian regulations have gone further in the direction of performance requirements than most other countries. This applies to all types of requirements, including requirements for usability, functionality and accessibility. Hardly any specifications are to be found in the regulations. Ideally, this lack of specifications should give designers the opportunity to develop innovative answers and hence to respond to different contexts and needs. Still, many architects and builders ask for clear specifications, in order to simplify and speed up design processes and make control of solutions easier. Many architects understand guidelines as minimum requirements, and are thus reproducing the identical solutions without considering the context and the needs of the users. They see accessibility as another regulatory pressure and requirements as restrictions rather than positive incentives. However, there are examples of designers who have internalised the regulatory framework and thus are able to create and integrate inclusive design in their daily work. Based on recent research conducted by SINTEF Building and Infrastructure and financed by the Norwegian State Housing Bank, this paper presents examples of practice where dwellings have been developed within a framework of universal design. Focus of the research has been on the approach of the design team and their understanding and use of the regulatory framework in order to create better homes in dialogue with the building authorities. Main objectives are to: - Contribute to better understanding of universal design as a tool and a method to improve housing quality and usability - Investigate the conditions for developing dwellings with innovative and functional solutions in compliance with the building code - Discuss challenges in interpreting the requirements and in taking the needs of various resident groups into account.

24 CFR 941.203 - Design and construction standards.

Code of Federal Regulations, 2013 CFR

2013-04-01

... national building code, such as Uniform Building Code, Council of American Building Officials Code, or Building Officials Conference of America Code; (2) Applicable State and local laws, codes, ordinances, and... intended to serve. Building design and construction shall strive to encourage in residents a proprietary...

24 CFR 941.203 - Design and construction standards.

Code of Federal Regulations, 2012 CFR

2012-04-01

... national building code, such as Uniform Building Code, Council of American Building Officials Code, or Building Officials Conference of America Code; (2) Applicable State and local laws, codes, ordinances, and... intended to serve. Building design and construction shall strive to encourage in residents a proprietary...

41 CFR 128-1.8005 - Seismic safety standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the model building codes that the Interagency Committee on Seismic Safety in Construction (ICSSC...) Uniform Building Code (UBC); (2) The 1992 Supplement to the Building Officials and Code Administrators International (BOCA) National Building Code (NBC); and (3) The 1992 Amendments to the Southern Building Code...

41 CFR 128-1.8005 - Seismic safety standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the model building codes that the Interagency Committee on Seismic Safety in Construction (ICSSC...) Uniform Building Code (UBC); (2) The 1992 Supplement to the Building Officials and Code Administrators International (BOCA) National Building Code (NBC); and (3) The 1992 Amendments to the Southern Building Code...

41 CFR 128-1.8005 - Seismic safety standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the model building codes that the Interagency Committee on Seismic Safety in Construction (ICSSC...) Uniform Building Code (UBC); (2) The 1992 Supplement to the Building Officials and Code Administrators International (BOCA) National Building Code (NBC); and (3) The 1992 Amendments to the Southern Building Code...

41 CFR 128-1.8005 - Seismic safety standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the model building codes that the Interagency Committee on Seismic Safety in Construction (ICSSC...) Uniform Building Code (UBC); (2) The 1992 Supplement to the Building Officials and Code Administrators International (BOCA) National Building Code (NBC); and (3) The 1992 Amendments to the Southern Building Code...

Field Testing of Compartmentalization Methods for Multifamily Construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, K.; Lstiburek, J. W.

2015-03-01

The 2012 International Energy Conservation Code (IECC) has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure (3 ACH50) for single-family and multifamily construction (in climate zones 3–8). The Leadership in Energy & Environmental Design certification program and ASHRAE Standard 189 have comparable compartmentalization requirements. ASHRAE Standard 62.2 will soon be responsible for all multifamily ventilation requirements (low rise and high rise); it has an exceptionally stringent compartmentalization requirement. These code and program requirements are driving the need for easier and more effective methods of compartmentalization in multifamily buildings.

12 CFR 1807.503 - Project completion.

Code of Federal Regulations, 2012 CFR

2012-01-01

... applicable: One of three model codes (Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI)); or the Council of American Building Officials (CABO) one or two family... must meet the current edition of the Model Energy Code published by the Council of American Building...

12 CFR 1807.503 - Project completion.

Code of Federal Regulations, 2013 CFR

2013-01-01

... applicable: One of three model codes (Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI)); or the Council of American Building Officials (CABO) one or two family... must meet the current edition of the Model Energy Code published by the Council of American Building...

12 CFR 1807.503 - Project completion.

Code of Federal Regulations, 2014 CFR

2014-01-01

... applicable: One of three model codes (Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI)); or the Council of American Building Officials (CABO) one or two family... must meet the current edition of the Model Energy Code published by the Council of American Building...

12 CFR 1807.503 - Project completion.

Code of Federal Regulations, 2011 CFR

2011-01-01

... applicable: One of three model codes (Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI)); or the Council of American Building Officials (CABO) one or two family... must meet the current edition of the Model Energy Code published by the Council of American Building...

Country Report on Building Energy Codes in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shui, Bin; Evans, Meredydd

2009-04-06

This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America . This reports gives an overview of the development of building energy codes in Canada, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, lighting, and water heating) for commercial and residential buildingsmore » in Canada.« less

Residential photovoltaic module and array requirements study

NASA Technical Reports Server (NTRS)

Nearhoof, S. L.; Oster, J. R.

1979-01-01

Design requirements for photovoltaic modules and arrays used in residential applications were identified. Building codes and referenced standards were reviewed for their applicability to residential photovoltaic array installations. Four installation types were identified - integral (replaces roofing), direct (mounted on top of roofing), stand-off (mounted away from roofing), and rack (for flat or low slope roofs, or ground mounted). Installation costs were developed for these mounting types as a function of panel/module size. Studies were performed to identify optimum module shapes and sizes and operating voltage cost drivers. It is concluded that there are no perceived major obstacles to the use of photovoltaic modules in residential arrays. However, there is no applicable building code category for residential photovoltaic modules and arrays and additional work with standards writing organizations is needed to develop residential module and array requirements.

Using Third-Party Inspectors in Building Energy Codes Enforcement in India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Evans, Meredydd; Kumar, Pradeep

India is experiencing fast income growth and urbanization, and this leads to unprecedented increases in demand for building energy services and resulting energy consumption. In response to rapid growth in building energy use, the Government of India issued the Energy Conservation Building Code (ECBC) in 2007, which is consistent with and based on the 2001 Energy Conservation Act. ECBC implementation has been voluntary since its enactment and a few states have started to make progress towards mandatory implementation. Rajasthan is the first state in India to adopt ECBC as a mandatory code. The State adopted ECBC with minor additions onmore » March 28, 2011 through a stakeholder process; it became mandatory in Rajasthan on September 28, 2011. Tamil Nadu, Gujarat, and Andhra Pradesh have started to draft an implementation roadmap and build capacity for its implementation. The Bureau of Energy Efficiency (BEE) plans to encourage more states to adopt ECBC in the near future, including Haryana, Uttar Pradesh, Karnataka, Maharashtra, West Bengal, and Delhi. Since its inception, India has applied the code on a voluntary basis, but the Government of India is developing a strategy to mandate compliance. Implementing ECBC requires coordination between the Ministry of Power and the Ministry of Urban Development at the national level as well as interdepartmental coordination at the state level. One challenge is that the Urban Local Bodies (ULBs), the enforcement entities of building by-laws, lack capacity to implement ECBC effectively. For example, ULBs in some states might find the building permitting procedures to be too complex; in other cases, lack of awareness and technical knowledge on ECBC slows down the amendment of local building by-laws as well as ECBC implementation. The intent of this white paper is to share with Indian decision-makers code enforcement approaches: through code officials, third-party inspectors, or a hybrid approach. Given the limited capacity and human resources available in the state and local governments, involving third-party inspectors could rapidly expand the capacity for plan reviews and broad implementation. However, the procedures of involving third-parties need to be carefully designed in order to guarantee a fair process. For example, there should be multiple checks and certification requirements for third-party inspectors, and the government should have the final approval when third-party inspectors are used in a project. This paper discusses different approaches of involving third-parties in ECBC enforcement; the Indian states may choose the approaches that work best in their given circumstances.« less

State Requirements for Educational Facilities, 1999.

ERIC Educational Resources Information Center

Florida State Dept. of Education, Tallahassee. Office of Educational Facilities.

This updated, two-volume document provides guidance for those involved in the educational facilities procurement process, and includes recent legislative changes affecting the state of Florida's building code. The first volume is organized by the sequence of steps required in the facilities procurement process and presents state requirements for…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sesigur, Haluk; Cili, Feridun

Seismic isolation is an effective design strategy to mitigate the seismic hazard wherein the structure and its contents are protected from the damaging effects of an earthquake. This paper presents the Hangar Project in Sabiha Goekcen Airport which is located in Istanbul, Turkey. Seismic isolation system where the isolation layer arranged at the top of the columns is selected. The seismic hazard analysis, superstructure design, isolator design and testing were based on the Uniform Building Code (1997) and met all requirements of the Turkish Earthquake Code (2007). The substructure which has the steel vertical trusses on facades and RC Hmore » shaped columns in the middle axis of the building was designed with an R factor limited to 2.0 in accordance with Turkish Earthquake Code. In order to verify the effectiveness of the isolation system, nonlinear static and dynamic analyses are performed. The analysis revealed that isolated building has lower base shear (approximately 1/4) against the non-isolated structure.« less

7 CFR 3550.10 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., meets or exceeds the requirements of the recognized development standards (model building codes) for... Federally Manufactured Home Construction and Safety Standard and RHS Thermal Performance Standards. It is...

7 CFR 3550.10 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., meets or exceeds the requirements of the recognized development standards (model building codes) for... Federally Manufactured Home Construction and Safety Standard and RHS Thermal Performance Standards. It is...

7 CFR 3550.10 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., meets or exceeds the requirements of the recognized development standards (model building codes) for... Federally Manufactured Home Construction and Safety Standard and RHS Thermal Performance Standards. It is...

Tribal Green Building Administrative Code Example

EPA Pesticide Factsheets

This Tribal Green Building Administrative Code Example can be used as a template for technical code selection (i.e., building, electrical, plumbing, etc.) to be adopted as a comprehensive building code.

A long-term, integrated impact assessment of alternative building energy code scenarios in China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Eom, Jiyong; Evans, Meredydd

2014-04-01

China is the second largest building energy user in the world, ranking first and third in residential and commercial energy consumption. Beginning in the early 1980s, the Chinese government has developed a variety of building energy codes to improve building energy efficiency and reduce total energy demand. This paper studies the impact of building energy codes on energy use and CO2 emissions by using a detailed building energy model that represents four distinct climate zones each with three building types, nested in a long-term integrated assessment framework GCAM. An advanced building stock module, coupled with the building energy model, ismore » developed to reflect the characteristics of future building stock and its interaction with the development of building energy codes in China. This paper also evaluates the impacts of building codes on building energy demand in the presence of economy-wide carbon policy. We find that building energy codes would reduce Chinese building energy use by 13% - 22% depending on building code scenarios, with a similar effect preserved even under the carbon policy. The impact of building energy codes shows regional and sectoral variation due to regionally differentiated responses of heating and cooling services to shell efficiency improvement.« less

Evaluation of Passive Vents in New Construction Multifamily Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sean Maxwell; Berger, David; Zuluaga, Marc

Exhaust ventilation and corresponding outdoor air strategies are being implemented in high performance, new construction, multifamily buildings to meet program or code requirements for improved indoor air quality, but a lack of clear design guidance is resulting in poor performance of these systems despite the best intentions of the programs or standards.

24 CFR 92.251 - Property standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., as applicable, one of three model codes: Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI); or the Council of American Building Officials (CABO) one or two...) Housing that is constructed or rehabilitated with HOME funds must meet all applicable local codes...

24 CFR 92.251 - Property standards.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., as applicable, one of three model codes: Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI); or the Council of American Building Officials (CABO) one or two...) Housing that is constructed or rehabilitated with HOME funds must meet all applicable local codes...

24 CFR 92.251 - Property standards.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., as applicable, one of three model codes: Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI); or the Council of American Building Officials (CABO) one or two...) Housing that is constructed or rehabilitated with HOME funds must meet all applicable local codes...

24 CFR 92.251 - Property standards.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., as applicable, one of three model codes: Uniform Building Code (ICBO), National Building Code (BOCA), Standard (Southern) Building Code (SBCCI); or the Council of American Building Officials (CABO) one or two...) Housing that is constructed or rehabilitated with HOME funds must meet all applicable local codes...

24 CFR 200.925c - Model codes.

Code of Federal Regulations, 2012 CFR

2012-04-01

... below. (1) Model Building Codes—(i) The BOCA National Building Code, 1993 Edition, The BOCA National..., Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood... number 2 (Chapter 7) of the Building Code, but including the Appendices of the Code. Available from...

24 CFR 200.925c - Model codes.

Code of Federal Regulations, 2013 CFR

2013-04-01

... below. (1) Model Building Codes—(i) The BOCA National Building Code, 1993 Edition, The BOCA National..., Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood... number 2 (Chapter 7) of the Building Code, but including the Appendices of the Code. Available from...

24 CFR 200.925c - Model codes.

Code of Federal Regulations, 2014 CFR

2014-04-01

... below. (1) Model Building Codes—(i) The BOCA National Building Code, 1993 Edition, The BOCA National..., Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood... number 2 (Chapter 7) of the Building Code, but including the Appendices of the Code. Available from...

Building Interactive Simulations in Web Pages without Programming.

PubMed

Mailen Kootsey, J; McAuley, Grant; Bernal, Julie

2005-01-01

A software system is described for building interactive simulations and other numerical calculations in Web pages. The system is based on a new Java-based software architecture named NumberLinX (NLX) that isolates each function required to build the simulation so that a library of reusable objects could be assembled. The NLX objects are integrated into a commercial Web design program for coding-free page construction. The model description is entered through a wizard-like utility program that also functions as a model editor. The complete system permits very rapid construction of interactive simulations without coding. A wide range of applications are possible with the system beyond interactive calculations, including remote data collection and processing and collaboration over a network.

Building Energy Codes: Policy Overview and Good Practices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cox, Sadie

2016-02-19

Globally, 32% of total final energy consumption is attributed to the building sector. To reduce energy consumption, energy codes set minimum energy efficiency standards for the building sector. With effective implementation, building energy codes can support energy cost savings and complementary benefits associated with electricity reliability, air quality improvement, greenhouse gas emission reduction, increased comfort, and economic and social development. This policy brief seeks to support building code policymakers and implementers in designing effective building code programs.

Build-up Approach to Updating the Mock Quiet Spike(TradeMark) Beam Model

NASA Technical Reports Server (NTRS)

Herrera, Claudia Y.; Pak, Chan-gi

2007-01-01

A crucial part of aircraft design is ensuring that the required margin for flutter is satisfied. A trustworthy flutter analysis, which begins by possessing an accurate dynamics model, is necessary for this task. Traditionally, a model was updated manually by fine tuning specific stiffness parameters until the analytical results matched test data. This is a time consuming iterative process. NASA Dryden Flight Research Center has developed a mode matching code to execute this process in a more efficient manner. Recently, this code was implemented in the F-15B/Quiet Spike(TradeMark) (Gulfstream Aerospace Corporation, Savannah, Georgia) model update. A build-up approach requiring several ground vibration test configurations and a series of model updates was implemented in order to determine the connection stiffness between aircraft and test article. The mode matching code successfully updated various models for the F-15B/Quiet Spike(TradeMark) project to within 1 percent error in frequency and the modal assurance criteria values ranged from 88.51-99.42 percent.

Build-up Approach to Updating the Mock Quiet Spike(TM)Beam Model

NASA Technical Reports Server (NTRS)

Herrera, Claudia Y.; Pak, Chan-gi

2007-01-01

A crucial part of aircraft design is ensuring that the required margin for flutter is satisfied. A trustworthy flutter analysis, which begins by possessing an accurate dynamics model, is necessary for this task. Traditionally, a model was updated manually by fine tuning specific stiffness parameters until the analytical results matched test data. This is a time consuming iterative process. The NASA Dryden Flight Research Center has developed a mode matching code to execute this process in a more efficient manner. Recently, this code was implemented in the F-15B/Quiet Spike (Gulfstream Aerospace Corporation, Savannah, Georgia) model update. A build-up approach requiring several ground vibration test configurations and a series of model updates was implemented to determine the connection stiffness between aircraft and test article. The mode matching code successfully updated various models for the F-15B/Quiet Spike project to within 1 percent error in frequency and the modal assurance criteria values ranged from 88.51-99.42 percent.

Building Code Compliance and Enforcement: The Experience of SanFrancisco's Residential Energy Conservation Ordinanace and California'sBuildign Standards for New Construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vine, E.

1990-11-01

As part of Lawrence Berkeley Laboratory's (LBL) technical assistance to the Sustainable City Project, compliance and enforcement activities related to local and state building codes for existing and new construction were evaluated in two case studies. The analysis of the City of San Francisco's Residential Energy Conservation Ordinance (RECO) showed that a limited, prescriptive energy conservation ordinance for existing residential construction can be enforced relatively easily with little administrative costs, and that compliance with such ordinances can be quite high. Compliance with the code was facilitated by extensive publicity, an informed public concerned with the cost of energy and knowledgeablemore » about energy efficiency, the threat of punishment (Order of Abatement), the use of private inspectors, and training workshops for City and private inspectors. The analysis of California's Title 24 Standards for new residential and commercial construction showed that enforcement of this type of code for many climate zones is more complex and requires extensive administrative support for education and training of inspectors, architects, engineers, and builders. Under this code, prescriptive and performance approaches for compliance are permitted, resulting in the demand for alternative methods of enforcement: technical assistance, plan review, field inspection, and computer analysis. In contrast to existing construction, building design and new materials and construction practices are of critical importance in new construction, creating a need for extensive technical assistance and extensive interaction between enforcement personnel and the building community. Compliance problems associated with building design and installation did occur in both residential and nonresidential buildings. Because statewide codes are enforced by local officials, these problems may increase over time as energy standards change and become more complex and as other standards (eg, health and safety codes) remain a higher priority. The California Energy Commission realizes that code enforcement by itself is insufficient and expects that additional educational and technical assistance efforts (eg, manuals, training programs, and toll-free telephone lines) will ameliorate these problems.« less

Energy and Energy Cost Savings Analysis of the 2015 IECC for Commercial Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jian; Xie, YuLong; Athalye, Rahul A.

As required by statute (42 USC 6833), DOE recently issued a determination that ANSI/ASHRAE/IES Standard 90.1-2013 would achieve greater energy efficiency in buildings subject to the code compared to the 2010 edition of the standard. Pacific Northwest National Laboratory (PNNL) conducted an energy savings analysis for Standard 90.1-2013 in support of its determination . While Standard 90.1 is the model energy standard for commercial and multi-family residential buildings over three floors (42 USC 6833), many states have historically adopted the International Energy Conservation Code (IECC) for both residential and commercial buildings. This report provides an assessment as to whether buildingsmore » constructed to the commercial energy efficiency provisions of the 2015 IECC would save energy and energy costs as compared to the 2012 IECC. PNNL also compared the energy performance of the 2015 IECC with the corresponding Standard 90.1-2013. The goal of this analysis is to help states and local jurisdictions make informed decisions regarding model code adoption.« less

A combinatorial code for pattern formation in Drosophila oogenesis.

PubMed

Yakoby, Nir; Bristow, Christopher A; Gong, Danielle; Schafer, Xenia; Lembong, Jessica; Zartman, Jeremiah J; Halfon, Marc S; Schüpbach, Trudi; Shvartsman, Stanislav Y

2008-11-01

Two-dimensional patterning of the follicular epithelium in Drosophila oogenesis is required for the formation of three-dimensional eggshell structures. Our analysis of a large number of published gene expression patterns in the follicle cells suggests that they follow a simple combinatorial code based on six spatial building blocks and the operations of union, difference, intersection, and addition. The building blocks are related to the distribution of inductive signals, provided by the highly conserved epidermal growth factor receptor and bone morphogenetic protein signaling pathways. We demonstrate the validity of the code by testing it against a set of patterns obtained in a large-scale transcriptional profiling experiment. Using the proposed code, we distinguish 36 distinct patterns for 81 genes expressed in the follicular epithelium and characterize their joint dynamics over four stages of oogenesis. The proposed combinatorial framework allows systematic analysis of the diversity and dynamics of two-dimensional transcriptional patterns and guides future studies of gene regulation.

Kayenta Township Building & Safety Department, Tribal Green Building Code Summit Presentation

EPA Pesticide Factsheets

Tribal Green Building Code Summit Presentation by Kayenta Township Building & Safety Department showing how they established the building department, developed a code adoption and enforcement process, and hired staff to carry out the work.

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 12 2013-01-01 2013-01-01 false Voluntary National Model Building Codes E Exhibit E... National Model Building Codes The following documents address the health and safety aspects of buildings and related structures and are voluntary national model building codes as defined in § 1924.4(h)(2) of...

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 12 2014-01-01 2013-01-01 true Voluntary National Model Building Codes E Exhibit E to... Model Building Codes The following documents address the health and safety aspects of buildings and related structures and are voluntary national model building codes as defined in § 1924.4(h)(2) of this...

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 12 2012-01-01 2012-01-01 false Voluntary National Model Building Codes E Exhibit E... National Model Building Codes The following documents address the health and safety aspects of buildings and related structures and are voluntary national model building codes as defined in § 1924.4(h)(2) of...

49 CFR 41.117 - Buildings built with Federal assistance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... architect's authenticated verifications of seismic design codes, standards, and practices used in the design... financial assistance, after July 14, 1993 must be designed and constructed in accord with seismic standards... of compliance with the seismic design and construction requirements of this part is required prior to...

Implementing newborn mock codes.

PubMed

Blakely, Teresa Gail

2007-01-01

This article describes the implementation of a newborn mock code program. Although the Neonatal Resuscitation Program (NRP) is one of the most widely used health education programs in the world and is required for most hospital providers who attend deliveries, research tells us that retention of NRP skills deteriorates rapidly after completion of the course. NRP requires coordination and cooperation among all providers; however, a lack of leadership and teamwork during resuscitation (often associated with a lack of confidence) has been noted. Implementation of newborn mock code scenarios can encourage teamwork, communication, skills building, and increased confidence levels of providers. Mock codes can help providers become strong team members and team leaders by helping them be better prepared for serious situations in the delivery room. Implementation of newborn mock codes can be effectively accomplished with appropriate planning and consideration for adult learning behaviors.

24 CFR 578.75 - General operations.

Code of Federal Regulations, 2014 CFR

2014-04-01

... assistance under this part must meet State or local building codes, and in the absence of State or local building codes, the International Residential Code or International Building Code (as applicable to the type of structure) of the International Code Council. (2) Services provided with assistance under this...

24 CFR 578.75 - General operations.

Code of Federal Regulations, 2013 CFR

2013-04-01

... assistance under this part must meet State or local building codes, and in the absence of State or local building codes, the International Residential Code or International Building Code (as applicable to the type of structure) of the International Code Council. (2) Services provided with assistance under this...

Promoting personal safety of building service workers: issues and challenges.

PubMed

Chen, Shelley I; Skillen, D Lynn

2006-06-01

This exploratory, descriptive study conducted at a large western Canadian university solicited perceptions of personal safety among building service workers who perform night shift work alone. Ten semi-structured interviews were conducted at approximately 10:00 p.m. or 7:00 a.m with a convenience sample of night building service workers in private or semi-private locations on the university campus. Transcribed interview data were subjected to inductive content analysis using descriptive, interpretive, and pattern coding (Miles & Huberman, 1994). Results suggest that building service night shift workers are exposed to personal safety hazards in their physical and psychosocial work environments. In addition, culturally and linguistically appropriate delivery of safety training and education about policies and procedures is required for culturally diverse building service workers. Promotion of personal safety in this heterogeneous worker population requires due diligence, assessment, and advocacy.

Nuclear Energy Advanced Modeling and Simulation (NEAMS) waste Integrated Performance and Safety Codes (IPSC) : gap analysis for high fidelity and performance assessment code development.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Joon H.; Siegel, Malcolm Dean; Arguello, Jose Guadalupe, Jr.

2011-03-01

This report describes a gap analysis performed in the process of developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repositorymore » designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with rigorous verification, validation, and software quality requirements. The gap analyses documented in this report were are performed during an initial gap analysis to identify candidate codes and tools to support the development and integration of the Waste IPSC, and during follow-on activities that delved into more detailed assessments of the various codes that were acquired, studied, and tested. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. The gap analysis indicates that significant capabilities may already exist in the existing THC codes although there is no single code able to fully account for all physical and chemical processes involved in a waste disposal system. Large gaps exist in modeling chemical processes and their couplings with other processes. The coupling of chemical processes with flow transport and mechanical deformation remains challenging. The data for extreme environments (e.g., for elevated temperature and high ionic strength media) that are needed for repository modeling are severely lacking. In addition, most of existing reactive transport codes were developed for non-radioactive contaminants, and they need to be adapted to account for radionuclide decay and in-growth. The accessibility to the source codes is generally limited. Because the problems of interest for the Waste IPSC are likely to result in relatively large computational models, a compact memory-usage footprint and a fast/robust solution procedure will be needed. A robust massively parallel processing (MPP) capability will also be required to provide reasonable turnaround times on the analyses that will be performed with the code. A performance assessment (PA) calculation for a waste disposal system generally requires a large number (hundreds to thousands) of model simulations to quantify the effect of model parameter uncertainties on the predicted repository performance. A set of codes for a PA calculation must be sufficiently robust and fast in terms of code execution. A PA system as a whole must be able to provide multiple alternative models for a specific set of physical/chemical processes, so that the users can choose various levels of modeling complexity based on their modeling needs. This requires PA codes, preferably, to be highly modularized. Most of the existing codes have difficulties meeting these requirements. Based on the gap analysis results, we have made the following recommendations for the code selection and code development for the NEAMS waste IPSC: (1) build fully coupled high-fidelity THCMBR codes using the existing SIERRA codes (e.g., ARIA and ADAGIO) and platform, (2) use DAKOTA to build an enhanced performance assessment system (EPAS), and build a modular code architecture and key code modules for performance assessments. The key chemical calculation modules will be built by expanding the existing CANTERA capabilities as well as by extracting useful components from other existing codes.« less

Implementing nationally determined contributions: building energy policies in India’s mitigation strategy

NASA Astrophysics Data System (ADS)

Yu, Sha; Evans, Meredydd; Kyle, Page; Vu, Linh; Tan, Qing; Gupta, Ashu; Patel, Pralit

2018-03-01

The Nationally Determined Contributions are allowing countries to examine options for reducing emissions through a range of domestic policies. India, like many developing countries, has committed to reducing emissions through specific policies, including building energy codes. Here we assess the potential of these sectoral policies to help in achieving mitigation targets. Collectively, it is critically important to see the potential impact of such policies across developing countries in meeting national and global emission goals. Buildings accounted for around one third of global final energy use in 2010, and building energy consumption is expected to increase as income grows in developing countries. Using the Global Change Assessment Model, this study finds that implementing a range of energy efficiency policies robustly can reduce total Indian building energy use by 22% and lower total Indian carbon dioxide emissions by 9% in 2050 compared to the business-as-usual scenario. Among various policies, energy codes for new buildings can result in the most significant savings. For all building energy policies, well-coordinated, consistent implementation is critical, which requires coordination across different departments and agencies, improving capacity of stakeholders, and developing appropriate institutions to facilitate policy implementation.

Measure Guideline: Ventilation Guidance for Residential High-Performance New Construction - Multifamily

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lstiburek, Joseph

2017-01-01

The measure guideline provides ventilation guidance for residential high performance multifamily construction that incorporates the requirements of the ASHRAE 62.2 ventilation and indoor air quality standard. The measure guideline focus is on the decision criteria for weighing cost and performance of various ventilation systems. The measure guideline is intended for contractors, builders, developers, designers and building code officials. The guide may also be helpful to building owners wishing to learn more about ventilation strategies available for their buildings. The measure guideline includes specific design and installation instructions for the most cost effective and performance effective solutions for ventilation in multifamilymore » units that satisfies the requirements of ASHRAE 62.2-2016.« less

Measure Guideline: Ventilation Guidance for Residential High-Performance New Construction - Multifamily

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lstiburek, Joseph

The measure guideline provides ventilation guidance for residential high performance multifamily construction that incorporates the requirements of the ASHRAE 62.2 ventilation and indoor air quality standard. The measure guideline focus is on the decision criteria for weighing cost and performance of various ventilation systems. The measure guideline is intended for contractors, builders, developers, designers and building code officials. The guide may also be helpful to building owners wishing to learn more about ventilation strategies available for their buildings. The measure guideline includes specific design and installation instructions for the most cost effective and performance effective solutions for ventilation in multifamilymore » units that satisfies the requirements of ASHRAE 62.2-2016.« less

29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

Code of Federal Regulations, 2013 CFR

2013-07-01

.... • Accident Prevention Manual for Industrial Operations; Eighth Edition; National Safety Council. • Building Code Requirements for Reinforced Concrete (ACI 318-83). • Formwork for Concrete (ACI SP-4...

29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

Code of Federal Regulations, 2014 CFR

2014-07-01

.... • Accident Prevention Manual for Industrial Operations; Eighth Edition; National Safety Council. • Building Code Requirements for Reinforced Concrete (ACI 318-83). • Formwork for Concrete (ACI SP-4...

29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

Code of Federal Regulations, 2011 CFR

2011-07-01

.... • Accident Prevention Manual for Industrial Operations; Eighth Edition; National Safety Council. • Building Code Requirements for Reinforced Concrete (ACI 318-83). • Formwork for Concrete (ACI SP-4...

29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

Code of Federal Regulations, 2012 CFR

2012-07-01

.... • Accident Prevention Manual for Industrial Operations; Eighth Edition; National Safety Council. • Building Code Requirements for Reinforced Concrete (ACI 318-83). • Formwork for Concrete (ACI SP-4...

Building a Better Campus: An Update on Building Codes.

ERIC Educational Resources Information Center

Madden, Michael J.

2002-01-01

Discusses the implications for higher education institutions in terms of facility planning, design, construction, and renovation of the move from regionally-developed model-building codes to two international sets of codes. Also addresses the new performance-based design option within the codes. (EV)

Building America Case Study: Evaluation of Passive Vents in New-Construction Multifamily Buildings, New York, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Exhaust ventilation and corresponding outdoor air strategies are being implemented in high-performance new construction multifamily buildings to meet program or code requirements for improved indoor air quality, but a lack of clear design guidance is resulting in poor performance of these systems despite the best intentions of the programs or standards. CARB's 2014 'Evaluation of Ventilation Strategies in New Construction Multifamily Buildings' consistently demonstrated that commonly used outdoor air strategies are not performing as expected. Of the four strategies evaluated in 2014, the exhaust ventilation system that relied on outdoor air from a pressurized corridor was ruled out as amore » potential best practice due to its conflict with meeting requirements within most fire codes. Outdoor air that is ducted directly to the apartments was a strategy determined to have the highest likelihood of success, but with higher first costs and operating costs. Outdoor air through space conditioning systems was also determined to have good performance potential, with proper design and execution. The fourth strategy, passive systems, was identified as the least expensive option for providing outdoor air directly to apartments, with respect to both first costs and operating costs. However, little is known about how they actually perform in real-world conditions or how to implement them effectively. Based on the lack of data available on the performance of these low-cost systems and their frequent use in the high-performance building programs that require a provision for outdoor air, this research project sought to further evaluate the performance of passive vents.« less

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Code of Federal Regulations, 2011 CFR

2011-01-01

... National Model Building Codes The following documents address the health and safety aspects of buildings... International, Inc., 4051 West Flossmoor Road, Country Club Hills, Illinois 60477. 2 Southern Building Code Congress International, Inc., 900 Montclair Road, Birmingham, Alabama 35213-1206. 3 International...

Importance biasing scheme implemented in the PRIZMA code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kandiev, I.Z.; Malyshkin, G.N.

1997-12-31

PRIZMA code is intended for Monte Carlo calculations of linear radiation transport problems. The code has wide capabilities to describe geometry, sources, material composition, and to obtain parameters specified by user. There is a capability to calculate path of particle cascade (including neutrons, photons, electrons, positrons and heavy charged particles) taking into account possible transmutations. Importance biasing scheme was implemented to solve the problems which require calculation of functionals related to small probabilities (for example, problems of protection against radiation, problems of detection, etc.). The scheme enables to adapt trajectory building algorithm to problem peculiarities.

The need for standards and codes to ensure an acoustically comfortable environment in multifamily housing buildings in Mexico City

NASA Astrophysics Data System (ADS)

Kotasek Gonzalez, Eduardo; Rodriguez Manzo, Fausto

2002-11-01

It is clear that almost all kinds of buildings require protection against noise and undesirable sounds, however, there are some countries where this is not yet regulated, such is the case of Mexico. Mexico City, the biggest city in the world could also be the noisiest. This is a problem which is today being debated; in fact there is no doubt that this has an important influence on the acoustic comfort conditions of dwellings, besides the habits and culture of the inhabitants, which are very different from those in the Anglo-Saxon countries. These are all details that must be taken into account in the design of an acoustic comfort standard for buildings in cities like Mexico. In this paper we deal with this problem and it suggests some recommendations to consider in a proposed acoustic comfort standard or code to be applied in the design of multifamily housing buildings in Mexico City.

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Voluntary National Model Building Codes E Exhibit E... HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY... National Model Building Codes The following documents address the health and safety aspects of buildings...

7 CFR 1792.103 - Seismic design and construction standards for new buildings.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Seismic Regulation for New Buildings. (b) Each of the following model codes or standards provides a level...) 548-2723. Fax: (703) 295-6211. (3) 2003 International Code Council (ICC) International Building Code... buildings. 1792.103 Section 1792.103 Agriculture Regulations of the Department of Agriculture (Continued...

7 CFR 1792.103 - Seismic design and construction standards for new buildings.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Seismic Regulation for New Buildings. (b) Each of the following model codes or standards provides a level...) 548-2723. Fax: (703) 295-6211. (3) 2003 International Code Council (ICC) International Building Code... buildings. 1792.103 Section 1792.103 Agriculture Regulations of the Department of Agriculture (Continued...

7 CFR 1792.103 - Seismic design and construction standards for new buildings.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Seismic Regulation for New Buildings. (b) Each of the following model codes or standards provides a level...) 548-2723. Fax: (703) 295-6211. (3) 2003 International Code Council (ICC) International Building Code... buildings. 1792.103 Section 1792.103 Agriculture Regulations of the Department of Agriculture (Continued...

7 CFR 1792.103 - Seismic design and construction standards for new buildings.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Seismic Regulation for New Buildings. (b) Each of the following model codes or standards provides a level...) 548-2723. Fax: (703) 295-6211. (3) 2003 International Code Council (ICC) International Building Code... buildings. 1792.103 Section 1792.103 Agriculture Regulations of the Department of Agriculture (Continued...

Automated and fast building of three-dimensional RNA structures.

PubMed

Zhao, Yunjie; Huang, Yangyu; Gong, Zhou; Wang, Yanjie; Man, Jianfen; Xiao, Yi

2012-01-01

Building tertiary structures of non-coding RNA is required to understand their functions and design new molecules. Current algorithms of RNA tertiary structure prediction give satisfactory accuracy only for small size and simple topology and many of them need manual manipulation. Here, we present an automated and fast program, 3dRNA, for RNA tertiary structure prediction with reasonable accuracy for RNAs of larger size and complex topology.

Potential Job Creation in Rhode Island as a Result of Adopting New Residential Building Energy Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Michael J.; Niemeyer, Jackie M.

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levelsmore » of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.« less

Potential Job Creation in Minnesota as a Result of Adopting New Residential Building Energy Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Michael J.; Niemeyer, Jackie M.

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levelsmore » of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.« less

Potential Job Creation in Tennessee as a Result of Adopting New Residential Building Energy Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Michael J.; Niemeyer, Jackie M.

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levelsmore » of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.« less

Potential Job Creation in Nevada as a Result of Adopting New Residential Building Energy Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Michael J.; Niemeyer, Jackie M.

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levelsmore » of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.« less

SAFETY IN THE DESIGN OF SCIENCE LABORATORIES AND BUILDING CODES.

ERIC Educational Resources Information Center

HOROWITZ, HAROLD

THE DESIGN OF COLLEGE AND UNIVERSITY BUILDINGS USED FOR SCIENTIFIC RESEARCH AND EDUCATION IS DISCUSSED IN TERMS OF LABORATORY SAFETY AND BUILDING CODES AND REGULATIONS. MAJOR TOPIC AREAS ARE--(1) SAFETY RELATED DESIGN FEATURES OF SCIENCE LABORATORIES, (2) LABORATORY SAFETY AND BUILDING CODES, AND (3) EVIDENCE OF UNSAFE DESIGN. EXAMPLES EMPHASIZE…

A Comparative Study on Seismic Analysis of Bangladesh National Building Code (BNBC) with Other Building Codes

NASA Astrophysics Data System (ADS)

Bari, Md. S.; Das, T.

2013-09-01

Tectonic framework of Bangladesh and adjoining areas indicate that Bangladesh lies well within an active seismic zone. The after effect of earthquake is more severe in an underdeveloped and a densely populated country like ours than any other developed countries. Bangladesh National Building Code (BNBC) was first established in 1993 to provide guidelines for design and construction of new structure subject to earthquake ground motions in order to minimize the risk to life for all structures. A revision of BNBC 1993 is undergoing to make this up to date with other international building codes. This paper aims at the comparison of various provisions of seismic analysis as given in building codes of different countries. This comparison will give an idea regarding where our country stands when it comes to safety against earth quake. Primarily, various seismic parameters in BNBC 2010 (draft) have been studied and compared with that of BNBC 1993. Later, both 1993 and 2010 edition of BNBC codes have been compared graphically with building codes of other countries such as National Building Code of India 2005 (NBC-India 2005), American Society of Civil Engineering 7-05 (ASCE 7-05). The base shear/weight ratios have been plotted against the height of the building. The investigation in this paper reveals that BNBC 1993 has the least base shear among all the codes. Factored Base shear values of BNBC 2010 are found to have increased significantly than that of BNBC 1993 for low rise buildings (≤20 m) around the country than its predecessor. Despite revision of the code, BNBC 2010 (draft) still suggests less base shear values when compared to the Indian and American code. Therefore, this increase in factor of safety against the earthquake imposed by the proposed BNBC 2010 code by suggesting higher values of base shear is appreciable.

7 CFR 1717.855 - Application contents: Advance approval-100 percent private financing of distribution...

Code of Federal Regulations, 2011 CFR

2011-01-01

... lien accommodation or subordination and including the amount and maturity of the proposed loan, a... provisions of applicable model codes for any buildings to be constructed, as required by 7 CFR 1792.104; and...

National Tribal Building Codes Summit

EPA Pesticide Factsheets

National Tribal Building Codes summit statement developed to support tribes interested in adopting green and culturally-appropriate building systems to ensure safe, sustainable, affordable, and culturally-appropriate buildings on tribal lands.

Building Standards and Codes for Energy Conservation

ERIC Educational Resources Information Center

Gross, James G.; Pierlert, James H.

1977-01-01

Current activity intended to lead to energy conservation measures in building codes and standards is reviewed by members of the Office of Building Standards and Codes Services of the National Bureau of Standards. For journal availability see HE 508 931. (LBH)

Demonstration of a quantum error detection code using a square lattice of four superconducting qubits

PubMed Central

Córcoles, A.D.; Magesan, Easwar; Srinivasan, Srikanth J.; Cross, Andrew W.; Steffen, M.; Gambetta, Jay M.; Chow, Jerry M.

2015-01-01

The ability to detect and deal with errors when manipulating quantum systems is a fundamental requirement for fault-tolerant quantum computing. Unlike classical bits that are subject to only digital bit-flip errors, quantum bits are susceptible to a much larger spectrum of errors, for which any complete quantum error-correcting code must account. Whilst classical bit-flip detection can be realized via a linear array of qubits, a general fault-tolerant quantum error-correcting code requires extending into a higher-dimensional lattice. Here we present a quantum error detection protocol on a two-by-two planar lattice of superconducting qubits. The protocol detects an arbitrary quantum error on an encoded two-qubit entangled state via quantum non-demolition parity measurements on another pair of error syndrome qubits. This result represents a building block towards larger lattices amenable to fault-tolerant quantum error correction architectures such as the surface code. PMID:25923200

Demonstration of a quantum error detection code using a square lattice of four superconducting qubits.

PubMed

Córcoles, A D; Magesan, Easwar; Srinivasan, Srikanth J; Cross, Andrew W; Steffen, M; Gambetta, Jay M; Chow, Jerry M

2015-04-29

The ability to detect and deal with errors when manipulating quantum systems is a fundamental requirement for fault-tolerant quantum computing. Unlike classical bits that are subject to only digital bit-flip errors, quantum bits are susceptible to a much larger spectrum of errors, for which any complete quantum error-correcting code must account. Whilst classical bit-flip detection can be realized via a linear array of qubits, a general fault-tolerant quantum error-correcting code requires extending into a higher-dimensional lattice. Here we present a quantum error detection protocol on a two-by-two planar lattice of superconducting qubits. The protocol detects an arbitrary quantum error on an encoded two-qubit entangled state via quantum non-demolition parity measurements on another pair of error syndrome qubits. This result represents a building block towards larger lattices amenable to fault-tolerant quantum error correction architectures such as the surface code.

Ethical issues in a pediatric private practice.

PubMed

Jakubowitz, Melissa

2011-11-01

Building a successful pediatric private practice requires clinical expertise and an understanding of the business process, as well as familiarity with the American Speech-Language-Hearing Association Code of Ethics. This article provides an overview of the ethical issues that may be encountered when building a practice, including a look at marketing and advertising, financial management, privacy, and documentation. Ethically sound decision making is a key to a successful business. © Thieme Medical Publishers.

Development of probabilistic multimedia multipathway computer codes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, C.; LePoire, D.; Gnanapragasam, E.

2002-01-01

The deterministic multimedia dose/risk assessment codes RESRAD and RESRAD-BUILD have been widely used for many years for evaluation of sites contaminated with residual radioactive materials. The RESRAD code applies to the cleanup of sites (soils) and the RESRAD-BUILD code applies to the cleanup of buildings and structures. This work describes the procedure used to enhance the deterministic RESRAD and RESRAD-BUILD codes for probabilistic dose analysis. A six-step procedure was used in developing default parameter distributions and the probabilistic analysis modules. These six steps include (1) listing and categorizing parameters; (2) ranking parameters; (3) developing parameter distributions; (4) testing parameter distributionsmore » for probabilistic analysis; (5) developing probabilistic software modules; and (6) testing probabilistic modules and integrated codes. The procedures used can be applied to the development of other multimedia probabilistic codes. The probabilistic versions of RESRAD and RESRAD-BUILD codes provide tools for studying the uncertainty in dose assessment caused by uncertain input parameters. The parameter distribution data collected in this work can also be applied to other multimedia assessment tasks and multimedia computer codes.« less

Health information management: an introduction to disease classification and coding.

PubMed

Mony, Prem Kumar; Nagaraj, C

2007-01-01

Morbidity and mortality data constitute an important component of a health information system and their coding enables uniform data collation and analysis as well as meaningful comparisons between regions or countries. Strengthening the recording and reporting systems for health monitoring is a basic requirement for an efficient health information management system. Increased advocacy for and awareness of a uniform coding system together with adequate capacity building of physicians, coders and other allied health and information technology personnel would pave the way for a valid and reliable health information management system in India. The core requirements for the implementation of disease coding are: (i) support from national/institutional health administrators, (ii) widespread availability of the ICD-10 material for morbidity and mortality coding; (iii) enhanced human and financial resources; and (iv) optimal use of informatics. We describe the methodology of a disease classification and codification system as also its applications for developing and maintaining an effective health information management system for India.

25 CFR 900.125 - What shall a construction contract proposal contain?

Code of Federal Regulations, 2012 CFR

2012-04-01

... tribal building codes and engineering standards; (4) Structural integrity; (5) Accountability of funds..., standards and methods (including national, regional, state, or tribal building codes or construction... methods (including national, regional, state, or tribal building codes or construction industry standards...

25 CFR 900.125 - What shall a construction contract proposal contain?

Code of Federal Regulations, 2014 CFR

2014-04-01

... tribal building codes and engineering standards; (4) Structural integrity; (5) Accountability of funds..., standards and methods (including national, regional, state, or tribal building codes or construction... methods (including national, regional, state, or tribal building codes or construction industry standards...

25 CFR 900.125 - What shall a construction contract proposal contain?

Code of Federal Regulations, 2013 CFR

2013-04-01

... tribal building codes and engineering standards; (4) Structural integrity; (5) Accountability of funds..., standards and methods (including national, regional, state, or tribal building codes or construction... methods (including national, regional, state, or tribal building codes or construction industry standards...

25 CFR 900.125 - What shall a construction contract proposal contain?

Code of Federal Regulations, 2011 CFR

2011-04-01

... tribal building codes and engineering standards; (4) Structural integrity; (5) Accountability of funds..., standards and methods (including national, regional, state, or tribal building codes or construction... methods (including national, regional, state, or tribal building codes or construction industry standards...

25 CFR 900.125 - What shall a construction contract proposal contain?

Code of Federal Regulations, 2010 CFR

2010-04-01

... tribal building codes and engineering standards; (4) Structural integrity; (5) Accountability of funds..., standards and methods (including national, regional, state, or tribal building codes or construction... methods (including national, regional, state, or tribal building codes or construction industry standards...

78 FR 18321 - International Code Council: The Update Process for the International Codes and Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-26

... for Residential Construction in High Wind Regions. ICC 700: National Green Building Standard The..., coordinated, and necessary to regulate the built environment. Federal agencies frequently use these codes and... International Codes and Standards consist of the following: ICC Codes International Building Code. International...

75 FR 19944 - International Code Council: The Update Process for the International Codes and Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-16

... for Residential Construction in High Wind Areas. ICC 700: National Green Building Standard. The... Codes and Standards that are comprehensive, coordinated, and necessary to regulate the built environment... International Codes and Standards consist of the following: ICC Codes International Building Code. International...

24 CFR 200.926 - Minimum property standards for one and two family dwellings.

Code of Federal Regulations, 2012 CFR

2012-04-01

... property is to be located. (c) Standard for evaluating local or state building codes. The Secretary shall compare a local building code submitted under paragraph (d) of this section or a State code to the list of... each area and subarea on the list. (2) A State or local building code will be partially accepted if it...

24 CFR 200.926 - Minimum property standards for one and two family dwellings.

Code of Federal Regulations, 2014 CFR

2014-04-01

... property is to be located. (c) Standard for evaluating local or state building codes. The Secretary shall compare a local building code submitted under paragraph (d) of this section or a State code to the list of... each area and subarea on the list. (2) A State or local building code will be partially accepted if it...

24 CFR 200.926 - Minimum property standards for one and two family dwellings.

Code of Federal Regulations, 2013 CFR

2013-04-01

... property is to be located. (c) Standard for evaluating local or state building codes. The Secretary shall compare a local building code submitted under paragraph (d) of this section or a State code to the list of... each area and subarea on the list. (2) A State or local building code will be partially accepted if it...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, David; German, Alea

Building cost-effective, high-performance homes that provide superior comfort, health, and durability is the goal of the U.S. Department of Energy’s (DOE’s) Zero Energy Ready Home (ZERH) program. Building America research and other innovative programs throughout the country have addressed many of the technical challenges of building to the ZERH standard. The cost-effectiveness of measure packages that result in 30% source energy savings compared to a code-compliant home have been demonstrated. However, additional challenges remain, particularly with respect to convincing production builders of the strong business case for ZERH. The Alliance for Residential Building Innovation (ARBI) team believes that the keysmore » to successfully engaging builders and developers in the California market are to help them leverage development agreement requirements, code compliance requirements, incentives, and competitive market advantages of ZERH certification, and navigate through this process. A primary objective of this project was to gain a highly visible foothold for residential buildings that are built to the DOE ZERH specification that can be used to encourage participation by other California builders. This report briefly describes two single-family homes that were ZERH certified and focuses on the experience of working with developer Mutual Housing on a 62-unit multifamily community at the Spring Lake subdivision in Woodland, California. The Spring Lake project is expected to be the first ZERH-certified multifamily project in the country. This report discusses the challenges encountered, lessons learned, and how obstacles were overcome.« less

28 CFR 36.606 - Effect of certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... the question of whether equipment in a building built according to the code satisfies the Act's... buildings and facilities that comply with the certified code. A submitting official may reapply for...

28 CFR 36.606 - Effect of certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... the question of whether equipment in a building built according to the code satisfies the Act's... buildings and facilities that comply with the certified code. A submitting official may reapply for...

28 CFR 36.606 - Effect of certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... the question of whether equipment in a building built according to the code satisfies the Act's... buildings and facilities that comply with the certified code. A submitting official may reapply for...

28 CFR 36.606 - Effect of certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... the question of whether equipment in a building built according to the code satisfies the Act's... buildings and facilities that comply with the certified code. A submitting official may reapply for...

DOE Office of Scientific and Technical Information (OSTI.GOV)

The Profile Interface Generator (PIG) is a tool for loosely coupling applications and performance tools. It enables applications to write code that looks like standard C and Fortran functions calls, without requiring that applications link to specific implementations of those function calls. Performance tools can register with PIG in order to listen to only the calls that give information they care about. This interface reduces the build and configuration burden on application developers and allows semantic instrumentation to live in production codes without interfering with production runs.

Technical Support Document for Version 3.4.0 of the COMcheck Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan

2007-09-14

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989more » and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.« less

7 CFR 1717.860 - Lien accommodations and subordinations under section 306E of the RE Act.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accommodation and including the amount and maturity of the proposed loan, a general description of the... model codes for any buildings to be constructed, as required by 7 CFR 1792.104. All other elements of an...

Continuation of research into language concepts for the mission support environment: Source code

NASA Technical Reports Server (NTRS)

Barton, Timothy J.; Ratner, Jeremiah M.

1991-01-01

Research into language concepts for the Mission Control Center is presented. A computer code for source codes is presented. The file contains the routines which allow source code files to be created and compiled. The build process assumes that all elements and the COMP exist in the current directory. The build process places as much code generation as possible on the preprocessor as possible. A summary is given of the source files as used and/or manipulated by the build routine.

38 CFR 39.63 - Architectural design standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Association Life Safety Code and Errata (NFPA 101), the 2003 edition of the NFPA 5000, Building Construction... section, all applicable local and State building codes and regulations must be observed. In areas not subject to local or State building codes, the recommendations contained in the 2003 edition of the NFPA...

Increasing Flexibility in Energy Code Compliance: Performance Packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, Philip R.; Rosenberg, Michael I.

Energy codes and standards have provided significant increases in building efficiency over the last 38 years, since the first national energy code was published in late 1975. The most commonly used path in energy codes, the prescriptive path, appears to be reaching a point of diminishing returns. As the code matures, the prescriptive path becomes more complicated, and also more restrictive. It is likely that an approach that considers the building as an integrated system will be necessary to achieve the next real gains in building efficiency. Performance code paths are increasing in popularity; however, there remains a significant designmore » team overhead in following the performance path, especially for smaller buildings. This paper focuses on development of one alternative format, prescriptive packages. A method to develop building-specific prescriptive packages is reviewed based on a multiple runs of prototypical building models that are used to develop parametric decision analysis to determines a set of packages with equivalent energy performance. The approach is designed to be cost-effective and flexible for the design team while achieving a desired level of energy efficiency performance. A demonstration of the approach based on mid-sized office buildings with two HVAC system types is shown along with a discussion of potential applicability in the energy code process.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bdzil, John Bohdan

The full level-set function code, DSD3D, is fully described in LA-14336 (2007) [1]. This ASCI-supported, DSD code project was the last such LANL DSD code project that I was involved with before my retirement in 2007. My part in the project was to design and build the core DSD3D solver, which was to include a robust DSD boundary condition treatment. A robust boundary condition treatment was required, since for an important local “customer,” the only description of the explosives’ boundary was through volume fraction data. Given this requirement, the accuracy issues I had encountered with our “fast-tube,” narrowband, DSD2D solver,more » and the difficulty we had building an efficient MPI-parallel version of the narrowband DSD2D, I decided DSD3D should be built as a full level-set function code, using a totally local DSD boundary condition algorithm for the level-­set function, phi, which did not rely on the gradient of the level-­set function being one, |grad(phi)| = 1. The narrowband DSD2D solver was built on the assumption that |grad(phi)| could be driven to one, and near the boundaries of the explosive this condition was not being satisfied. Since the narrowband is typically no more than10*dx wide, narrowband methods are discrete methods with a fixed, non-­resolvable error, where the error is related to the thickness of the band: the narrower the band the larger the errors. Such a solution represents a discrete approximation to the true solution and does not limit to the solution of the underlying PDEs under grid resolution.The full level-­set function code, DSD3D, is fully described in LA-14336 (2007) [1]. This ASCI-­supported, DSD code project was the last such LANL DSD code project that I was involved with before my retirement in 2007. My part in the project was to design and build the core DSD3D solver, which was to include a robust DSD boundary condition treatment. A robust boundary condition treatment was required, since for an important local “customer,” the only description of the explosives’ boundary was through volume fraction data. Given this requirement, the accuracy issues I had encountered with our “fast-­tube,” narrowband, DSD2D solver, and the difficulty we had building an efficient MPI-parallel version of the narrowband DSD2D, I decided DSD3D should be built as a full level-­set function code, using a totally local DSD boundary condition algorithm for the level-­set function, phi, which did not rely on the gradient of the level-­set function being one, |grad(phi)| = 1. The narrowband DSD2D solver was built on the assumption that |grad(phi)| could be driven to one, and near the boundaries of the explosive this condition was not being satisfied. Since the narrowband is typically no more than10*dx wide, narrowband methods are discrete methods with a fixed, non-resolvable error, where the error is related to the thickness of the band: the narrower the band the larger the errors. Such a solution represents a discrete approximation to the true solution and does not limit to the solution of the underlying PDEs under grid resolution.« less

Evaluation of Passive Vents in New Construction Multifamily Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maxwell, Sean; Berger, David; Zuluaga, Marc

Exhaust ventilation and corresponding outdoor air strategies are being implemented in high-performance new construction multifamily buildings to meet program or code requirements for improved indoor air quality, but a lack of clear design guidance is resulting in poor performance of these systems despite the best intentions of the programs or standards. CARB's 2014 'Evaluation of Ventilation Strategies in New Construction Multifamily Buildings' consistently demonstrated that commonly used outdoor air strategies are not performing as expected. Of the four strategies evaluated in 2014, the exhaust ventilation system that relied on outdoor air from a pressurized corridor was ruled out as amore » potential best practice due to its conflict with meeting requirements within most fire codes. Outdoor air that is ducted directly to the apartments was a strategy determined to have the highest likelihood of success, but with higher first costs and operating costs. Outdoor air through space conditioning systems was also determined to have good performance potential, with proper design and execution. The fourth strategy, passive systems, was identified as the least expensive option for providing outdoor air directly to apartments, with respect to both first costs and operating costs. However, little is known about how they actually perform in real-world conditions or how to implement them effectively. Based on the lack of data available on the performance of these low-cost systems and their frequent use in the high-performance building programs that require a provision for outdoor air, this research project sought to further evaluate the performance of passive vents.« less

The HayWired earthquake scenario—Engineering implications

USGS Publications Warehouse

Detweiler, Shane T.; Wein, Anne M.

2018-04-18

The HayWired Earthquake Scenario—Engineering Implications is the second volume of U.S. Geological Survey (USGS) Scientific Investigations Report 2017–5013, which describes the HayWired scenario, developed by USGS and its partners. The scenario is a hypothetical yet scientifically realistic earthquake sequence that is being used to better understand hazards for the San Francisco Bay region during and after a magnitude-7 earthquake (mainshock) on the Hayward Fault and its aftershocks.Analyses in this volume suggest that (1) 800 deaths and 16,000 nonfatal injuries result from shaking alone, plus property and direct business interruption losses of more than $82 billion from shaking, liquefaction, and landslides; (2) the building code is designed to protect lives, but even if all buildings in the region complied with current building codes, 0.4 percent could collapse, 5 percent could be unsafe to occupy, and 19 percent could have restricted use; (3) people expect, prefer, and would be willing to pay for greater resilience of buildings; (4) more than 22,000 people could require extrication from stalled elevators, and more than 2,400 people could require rescue from collapsed buildings; (5) the average east-bay resident could lose water service for 6 weeks, some for as long as 6 months; (6) older steel-frame high-rise office buildings and new reinforced-concrete residential buildings in downtown San Francisco and Oakland could be unusable for as long as 10 months; (7) about 450 large fires could result in a loss of residential and commercial building floor area equivalent to more than 52,000 single-family homes and cause property (building and content) losses approaching $30 billion; and (8) combining earthquake early warning (ShakeAlert) with “drop, cover, and hold on” actions could prevent as many as 1,500 nonfatal injuries out of 18,000 total estimated nonfatal injuries from shaking and liquefaction hazards.

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

NASA Astrophysics Data System (ADS)

Toprak, A. Emre; Gülay, F. Gülten; Ruge, Peter

2008-07-01

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performed on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 m×7.80 m = 127.90 m2 with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher than the requirements of the Turkish Earthquake Code while the selected ground conditions represent the same characteristics. The main reason is that the ordinate of the horizontal elastic response spectrum for Eurocode 8 is increased by the soil factor. In TEC'07 force-based linear assessment, the seismic demands at cross-sections are to be checked with residual moment capacities; however, the chord rotations of primary ductile elements must be checked for Eurocode safety verifications. On the other hand, the demand curvatures from linear methods of analysis of Eurocode 8 together with TEC'07 are almost similar.

Purple L1 Milestone Review Panel TotalView Debugger Functionality and Performance for ASC Purple

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolfe, M

2006-12-12

ASC code teams require a robust software debugging tool to help developers quickly find bugs in their codes and get their codes running. Development debugging commonly runs up to 512 processes. Production jobs run up to full ASC Purple scale, and at times require introspection while running. Developers want a debugger that runs on all their development and production platforms and that works with all compilers and runtimes used with ASC codes. The TotalView Multiprocess Debugger made by Etnus was specified for ASC Purple to address this needed capability. The ASC Purple environment builds on the environment seen by TotalViewmore » on ASCI White. The debugger must now operate with the Power5 CPU, Federation switch, AIX 5.3 operating system including large pages, IBM compilers 7 and 9, POE 4.2 parallel environment, and rs6000 SLURM resource manager. Users require robust, basic debugger functionality with acceptable performance at development debugging scale. A TotalView installation must be provided at the beginning of the early user access period that meets these requirements. A functional enhancement, fast conditional data watchpoints, and a scalability enhancement, capability up to 8192 processes, are to be demonstrated.« less

Development of V/STOL methodology based on a higher order panel method

NASA Technical Reports Server (NTRS)

Bhateley, I. C.; Howell, G. A.; Mann, H. W.

1983-01-01

The development of a computational technique to predict the complex flowfields of V/STOL aircraft was initiated in which a number of modules and a potential flow aerodynamic code were combined in a comprehensive computer program. The modules were developed in a building-block approach to assist the user in preparing the geometric input and to compute parameters needed to simulate certain flow phenomena that cannot be handled directly within a potential flow code. The PAN AIR aerodynamic code, which is higher order panel method, forms the nucleus of this program. PAN AIR's extensive capability for allowing generalized boundary conditions allows the modules to interact with the aerodynamic code through the input and output files, thereby requiring no changes to the basic code and easy replacement of updated modules.

Wildfires and Schools

ERIC Educational Resources Information Center

National Clearinghouse for Educational Facilities, 2009

2009-01-01

This publication discusses conditions that feed wildfires, how a building catches fire, determining the school's risk, creating a survivable space for the school, the importance of maintenance, the fire-resistant school, meeting code requirements, and related flood and mudslide risks. Much of this publication has been adapted for schools from the…

Residential Building Energy Code Field Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Bartlett, M. Halverson, V. Mendon, J. Hathaway, Y. Xie

This document presents a methodology for assessing baseline energy efficiency in new single-family residential buildings and quantifying related savings potential. The approach was developed by Pacific Northwest National Laboratory (PNNL) for the U.S. Department of Energy (DOE) Building Energy Codes Program with the objective of assisting states as they assess energy efficiency in residential buildings and implementation of their building energy codes, as well as to target areas for improvement through energy codes and broader energy-efficiency programs. It is also intended to facilitate a consistent and replicable approach to research studies of this type and establish a transparent data setmore » to represent baseline construction practices across U.S. states.« less

Building codes: An often overlooked determinant of health.

PubMed

Chauvin, James; Pauls, Jake; Strobl, Linda

2016-05-01

Although the vast majority of the world's population spends most of their time in buildings, building codes are not often thought of as 'determinants of health'. The standards that govern the design, construction, and use of buildings affect our health, security, safety, and well-being. This is true for dwellings, schools, and universities, shopping centers, places of recreation, places of worship, health-care facilities, and workplaces. We urge proactive engagement by the global public health community in developing these codes, and in the design and implementation of health protection and health promotion activities intended to reduce the risk of injury, disability, and death, particularly when due to poor building code adoption/adaption, application, and enforcement.

Overcoming Codes and Standards Barriers to Innovations in Building Energy Efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, Pamala C.; Gilbride, Theresa L.

2015-02-15

In this journal article, the authors discuss approaches to overcoming building code barriers to energy-efficiency innovations in home construction. Building codes have been a highly motivational force for increasing the energy efficiency of new homes in the United States in recent years. But as quickly as the codes seem to be changing, new products are coming to the market at an even more rapid pace, sometimes offering approaches and construction techniques unthought of when the current code was first proposed, which might have been several years before its adoption by various jurisdictions. Due to this delay, the codes themselves canmore » become barriers to innovations that might otherwise be helping to further increase the efficiency, comfort, health or durability of new homes. . The U.S. Department of Energy’s Building America, a program dedicated to improving the energy efficiency of America’s housing stock through research and education, is working with the U.S. housing industry through its research teams to help builders identify and remove code barriers to innovation in the home construction industry. The article addresses several approaches that builders use to achieve approval for innovative building techniques when code barriers appear to exist.« less

Seismic assessment of Technical Area V (TA-V).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medrano, Carlos S.

The Technical Area V (TA-V) Seismic Assessment Report was commissioned as part of Sandia National Laboratories (SNL) Self Assessment Requirement per DOE O 414.1, Quality Assurance, for seismic impact on existing facilities at Technical Area-V (TA-V). SNL TA-V facilities are located on an existing Uniform Building Code (UBC) Seismic Zone IIB Site within the physical boundary of the Kirtland Air Force Base (KAFB). The document delineates a summary of the existing facilities with their safety-significant structure, system and components, identifies DOE Guidance, conceptual framework, past assessments and the present Geological and Seismic conditions. Building upon the past information and themore » evolution of the new seismic design criteria, the document discusses the potential impact of the new standards and provides recommendations based upon the current International Building Code (IBC) per DOE O 420.1B, Facility Safety and DOE G 420.1-2, Guide for the Mitigation of Natural Phenomena Hazards for DOE Nuclear Facilities and Non-Nuclear Facilities.« less

76 FR 13101 - Building Energy Codes Program: Presenting and Receiving Comments to DOE Proposed Changes to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

.... The IgCC is intended to provide a green model building code provisions for new and existing commercial... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket No. EERE-2011-BT-BC-0009] Building Energy Codes Program: Presenting and Receiving Comments to DOE Proposed Changes to the International Green Construction...

44 CFR 71.4 - Documentation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... evidence that the structure was not in compliance with the building code at the time it was built; and (2... evidence that the structure was not in compliance with the building code at the time it was built; and (2... structure and found no evidence that the structure was not in compliance with the building code at the time...

44 CFR 71.4 - Documentation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... evidence that the structure was not in compliance with the building code at the time it was built; and (2... evidence that the structure was not in compliance with the building code at the time it was built; and (2... structure and found no evidence that the structure was not in compliance with the building code at the time...

44 CFR 71.4 - Documentation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... evidence that the structure was not in compliance with the building code at the time it was built; and (2... evidence that the structure was not in compliance with the building code at the time it was built; and (2... structure and found no evidence that the structure was not in compliance with the building code at the time...

44 CFR 71.4 - Documentation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... evidence that the structure was not in compliance with the building code at the time it was built; and (2... evidence that the structure was not in compliance with the building code at the time it was built; and (2... structure and found no evidence that the structure was not in compliance with the building code at the time...

44 CFR 71.4 - Documentation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... evidence that the structure was not in compliance with the building code at the time it was built; and (2... evidence that the structure was not in compliance with the building code at the time it was built; and (2... structure and found no evidence that the structure was not in compliance with the building code at the time...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winkler, Jon; Booten, Chuck

Residential building codes and voluntary labeling programs are continually increasing the energy efficiency requirements of residential buildings. Improving a building's thermal enclosure and installing energy-efficient appliances and lighting can result in significant reductions in sensible cooling loads leading to smaller air conditioners and shorter cooling seasons. However due to fresh air ventilation requirements and internal gains, latent cooling loads are not reduced by the same proportion. Thus, it's becoming more challenging for conventional cooling equipment to control indoor humidity at part-load cooling conditions and using conventional cooling equipment in a non-conventional building poses the potential risk of high indoor humidity.more » The objective of this project was to investigate the impact the chosen design condition has on the calculated part-load cooling moisture load, and compare calculated moisture loads and the required dehumidification capacity to whole-building simulations. Procedures for sizing whole-house supplemental dehumidification equipment have yet to be formalized; however minor modifications to current Air-Conditioner Contractors of America (ACCA) Manual J load calculation procedures are appropriate for calculating residential part-load cooling moisture loads. Though ASHRAE 1% DP design conditions are commonly used to determine the dehumidification requirements for commercial buildings, an appropriate DP design condition for residential buildings has not been investigated. Two methods for sizing supplemental dehumidification equipment were developed and tested. The first method closely followed Manual J cooling load calculations; whereas the second method made more conservative assumptions impacting both sensible and latent loads.« less

Do Performance-Based Codes Support Universal Design in Architecture?

PubMed

Grangaard, Sidse; Frandsen, Anne Kathrine

2016-01-01

The research project 'An analysis of the accessibility requirements' studies how Danish architectural firms experience the accessibility requirements of the Danish Building Regulations and it examines their opinions on how future regulative models can support innovative and inclusive design - Universal Design (UD). The empirical material consists of input from six workshops to which all 700 Danish Architectural firms were invited, as well as eight group interviews. The analysis shows that the current prescriptive requirements are criticized for being too homogenous and possibilities for differentiation and zoning are required. Therefore, a majority of professionals are interested in a performance-based model because they think that such a model will support 'accessibility zoning', achieving flexibility because of different levels of accessibility in a building due to its performance. The common understanding of accessibility and UD is directly related to buildings like hospitals and care centers. When the objective is both innovative and inclusive architecture, the request of a performance-based model should be followed up by a knowledge enhancement effort in the building sector. Bloom's taxonomy of educational objectives is suggested as a tool for such a boost. The research project has been financed by the Danish Transport and Construction Agency.

Technical Support Document for Version 3.9.0 of the COMcheck Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan

2011-09-01

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989more » and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC are no longer included, but those sections remain in this document for reference purposes.« less

Technical Support Document for Version 3.9.1 of the COMcheck Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan

2012-09-01

COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989more » and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC and version 3.9.0 support for 2000 and 2001 IECC are no longer included, but those sections remain in this document for reference purposes.« less

Achieving 50% Energy Savings in Office Buildings, Advanced Energy Design Guides: Office Buildings (Brochure)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-09-01

This fact sheet summarizes recommendations for designing new office buildings that result in 50% less energy use than conventional designs meeting minimum code requirements. The recommendations are drawn from the Advanced Energy Design Guide for Small to Medium Office Buildings, an ASHRAE publication that provides comprehensive recommendations for designing low-energy-use office buildings with gross floor areas up to 100,000 ft2 (see sidebar). Designed as a stand-alone document, this fact sheet provides key principles and a set of prescriptive design recommendations appropriate for smaller office buildings with insufficient budgets to fully implement best practices for integrated design and optimized performance. Themore » recommendations have undergone a thorough analysis and review process through ASHRAE, and have been deemed the best combination of measures to achieve 50% savings in the greatest number of office buildings.« less

Building America Best Practices Series Volume 15: 40% Whole-House Energy Savings in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-09-01

This best practices guide is the 15th in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the hot-humid climate can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. The best practices describedmore » in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and those requirements are highlighted in the text. Requirements of the 2012 IECC and 2012 IRC are also noted in text and tables throughout the guide. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

Building America Best Practices Series Volume 16: 40% Whole-House Energy Savings in the Mixed-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-09-01

This best practices guide is the 16th in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the mixed-humid climate can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. The best practices describedmore » in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and those requirements are highlighted in the text. Requirements of the 2012 IECC and 2012 IRC are also noted in text and tables throughout the guide. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

Development of photovoltaic array and module safety requirements

NASA Technical Reports Server (NTRS)

1982-01-01

Safety requirements for photovoltaic module and panel designs and configurations likely to be used in residential, intermediate, and large-scale applications were identified and developed. The National Electrical Code and Building Codes were reviewed with respect to present provisions which may be considered to affect the design of photovoltaic modules. Limited testing, primarily in the roof fire resistance field was conducted. Additional studies and further investigations led to the development of a proposed standard for safety for flat-plate photovoltaic modules and panels. Additional work covered the initial investigation of conceptual approaches and temporary deployment, for concept verification purposes, of a differential dc ground-fault detection circuit suitable as a part of a photovoltaic array safety system.

41 CFR 102-80.80 - With what general accident and fire prevention policy must Federal agencies comply?

Code of Federal Regulations, 2014 CFR

2014-01-01

... maximum extent feasible, comply with one of the nationally recognized model building codes and with other nationally-recognized codes in their construction or alteration of each building in accordance with 40 U.S.C. 3312; and (f) Use the applicable national codes and standards as a guide for their building operations...

41 CFR 102-80.80 - With what general accident and fire prevention policy must Federal agencies comply?

Code of Federal Regulations, 2013 CFR

2013-07-01

... maximum extent feasible, comply with one of the nationally recognized model building codes and with other nationally-recognized codes in their construction or alteration of each building in accordance with 40 U.S.C. 3312; and (f) Use the applicable national codes and standards as a guide for their building operations...

41 CFR 102-80.80 - With what general accident and fire prevention policy must Federal agencies comply?

Code of Federal Regulations, 2012 CFR

2012-01-01

... maximum extent feasible, comply with one of the nationally recognized model building codes and with other nationally-recognized codes in their construction or alteration of each building in accordance with 40 U.S.C. 3312; and (f) Use the applicable national codes and standards as a guide for their building operations...

41 CFR 102-80.80 - With what general accident and fire prevention policy must Federal agencies comply?

Code of Federal Regulations, 2011 CFR

2011-01-01

... maximum extent feasible, comply with one of the nationally recognized model building codes and with other nationally-recognized codes in their construction or alteration of each building in accordance with 40 U.S.C. 3312; and (f) Use the applicable national codes and standards as a guide for their building operations...

Innovation and Standardization in School Building: A Proposal for the National Code in Italy.

ERIC Educational Resources Information Center

Ridolfi, Giuseppe

This document discusses the University of Florence's experience and concepts as it developed the research to define a proposal for designing a new national school building code. Section 1 examines the current school building code and the Italian Reform Process in Education between 1960 and 2000. Section 2 details and explains the new school…

Addressing Kitchen Contaminants for Healthy, Low-Energy Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stratton, J. Chris; Singer, Brett C.

2014-01-01

Cooking and cooking burners emit pollutants that can adversely affect indoor air quality in residences and significantly impact occupant health. Effective kitchen exhaust ventilation can reduce exposure to cooking-related air pollutants as an enabling step to healthier, low-energy homes. This report by Lawrence Berkeley National Laboratory identifies barriers to the widespread adoption of kitchen exhaust ventilation technologies and practice and proposes a suite of strategies to overcome these barriers. The recommendations have been vetted by a group of industry, regulatory, health, and research experts and stakeholders who convened for two meetings and provided input and feedback to early drafts ofmore » this document. The most fundamental barriers are (1) the common misconception, based on a sensory perception of risk, that kitchen exhaust when cooking is unnecessary and (2) the lack of a code requirement for kitchen ventilation in most U.S. locations. Highest priority objectives include the following: (1) Raise awareness among the public and the building industry of the need to install and routinely use kitchen ventilation; (2) Incorporate kitchen exhaust ventilation as a requirement of building codes and improve the mechanisms for code enforcement; (3) Provide best practice product and use-behavior guidance to ventilation equipment purchasers and installers, and; (4) Develop test methods and performance targets to advance development of high performance products. A specific, urgent need is the development of an over-the-range microwave that meets the airflow and sound requirements of ASHRAE Standard 62.2.« less

Addressing Kitchen Contaminants for Healthy, Low-Energy Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stratton, J. Chris; Singer, Brett C.

2014-01-01

Cooking and cooking burners emit pollutants that can adversely affect indoor air quality in residences and significantly impact occupant health. Effective kitchen exhaust ventilation can reduce exposure to cooking-related air pollutants as an enabling step to healthier, low-energy homes. This report identifies barriers to the widespread adoption of kitchen exhaust ventilation technologies and practice and proposes a suite of strategies to overcome these barriers. The recommendations have been vetted by a group of industry, regulatory, health, and research experts and stakeholders who convened for two web-based meetings and provided input and feedback to early drafts of this document. The mostmore » fundamental barriers are (1) the common misconception, based on a sensory perception of risk, that kitchen exhaust when cooking is unnecessary and (2) the lack of a code requirement for kitchen ventilation in most US locations. Highest priority objectives include the following: (1) Raise awareness among the public and the building industry of the need to install and routinely use kitchen ventilation; (2) Incorporate kitchen exhaust ventilation as a requirement of building codes and improve the mechanisms for code enforcement; (3) Provide best practice product and use-behavior guidance to ventilation equipment purchasers and installers, and; (4) Develop test methods and performance targets to advance development of high performance products. A specific, urgent need is the development of an over-the-range microwave that meets the airflow and sound requirements of ASHRAE Standard 62.2.« less

Automating RPM Creation from a Source Code Repository

DTIC Science & Technology

2012-02-01

apps/usr --with- libpq=/apps/ postgres make rm -rf $RPM_BUILD_ROOT umask 0077 mkdir -p $RPM_BUILD_ROOT/usr/local/bin mkdir -p $RPM_BUILD_ROOT...from a source code repository. %pre %prep %setup %build ./autogen.sh ; ./configure --with-db=/apps/db --with-libpq=/apps/ postgres make

Conversion of a Temporary Tent with Steel Frame into a Permanent Warehouse

NASA Astrophysics Data System (ADS)

Georgescu, Mircea; Ungureanu, Viorel; Grecea, Daniel; Petran, Ioan

2017-10-01

The paper is dealing with the problem of a functional conversion (involving both architectural and structural issues) applied to the case of an industrial building. As well known, temporary tents, designed according to the European Code EN13782, represent a remarkable stake on the building market and a fast and practical solution for some situations. It is exactly the case approached by the paper, where the investor has initially decided to erect on his platform a provisional shelter for agricultural machines and subsequent staff, built of a light steel structure covered by PVC roofing and cladding. This temporary tent has been acquired from a specialized supplier in form of a series product. After using the tent for a number of years, the investor has decided to convert the existing structure from architectural and structural point of view by switching to a permanent structure designed accordingly. Important changes were thus imposed both to the architectural part (technological flows, openings, facades) and especially to the structural part where this switch imposed a re-design to the codes of permanent structures (especially as far as climatic loadings are concerned). The required architectural change implied the building of a 70 cm high concrete plinth and replacing the PVC membrane temporary roofing and cladding by permanent 60 mm thick PUR sandwich panels. Together with a new system of openings this has led to renewed facades of the buildings. As for the structural change, the required conversion has imposed a thorough checking of the existing steel structure (very slender and typical to a tent) in view of transforming it into a permanent structure. The consolidation measures of the existing galvanized steel structure are described, together with the measures applied at infrastructure level in order to implement the required conversion.

Seismic instrumentation of buildings

USGS Publications Warehouse

Çelebi, Mehmet

2000-01-01

The purpose of this report is to provide information on how and why we deploy seismic instruments in and around building structures. The recorded response data from buildings and other instrumented structures can be and are being primarily used to facilitate necessary studies to improve building codes and therefore reduce losses of life and property during damaging earthquakes. Other uses of such data can be in emergency response situations in large urban environments. The report discusses typical instrumentation schemes, existing instrumentation programs, the steps generally followed in instrumenting a structure, selection and type of instruments, installation and maintenance requirements and data retrieval and processing issues. In addition, a summary section on how recorded response data have been utilized is included. The benefits from instrumentation of structural systems are discussed.

An assessment of seismic monitoring in the United States; requirement for an Advanced National Seismic System

USGS Publications Warehouse

,

1999-01-01

This report assesses the status, needs, and associated costs of seismic monitoring in the United States. It sets down the requirement for an effective, national seismic monitoring strategy and an advanced system linking national, regional, and urban monitoring networks. Modernized seismic monitoring can provide alerts of imminent strong earthquake shaking; rapid assessment of distribution and severity of earthquake shaking (for use in emergency response); warnings of a possible tsunami from an offshore earthquake; warnings of volcanic eruptions; information for correctly characterizing earthquake hazards and for improving building codes; and data on response of buildings and structures during earthquakes, for safe, cost-effective design, engineering, and construction practices in earthquake-prone regions.

SKIRT: The design of a suite of input models for Monte Carlo radiative transfer simulations

NASA Astrophysics Data System (ADS)

Baes, M.; Camps, P.

2015-09-01

The Monte Carlo method is the most popular technique to perform radiative transfer simulations in a general 3D geometry. The algorithms behind and acceleration techniques for Monte Carlo radiative transfer are discussed extensively in the literature, and many different Monte Carlo codes are publicly available. On the contrary, the design of a suite of components that can be used for the distribution of sources and sinks in radiative transfer codes has received very little attention. The availability of such models, with different degrees of complexity, has many benefits. For example, they can serve as toy models to test new physical ingredients, or as parameterised models for inverse radiative transfer fitting. For 3D Monte Carlo codes, this requires algorithms to efficiently generate random positions from 3D density distributions. We describe the design of a flexible suite of components for the Monte Carlo radiative transfer code SKIRT. The design is based on a combination of basic building blocks (which can be either analytical toy models or numerical models defined on grids or a set of particles) and the extensive use of decorators that combine and alter these building blocks to more complex structures. For a number of decorators, e.g. those that add spiral structure or clumpiness, we provide a detailed description of the algorithms that can be used to generate random positions. Advantages of this decorator-based design include code transparency, the avoidance of code duplication, and an increase in code maintainability. Moreover, since decorators can be chained without problems, very complex models can easily be constructed out of simple building blocks. Finally, based on a number of test simulations, we demonstrate that our design using customised random position generators is superior to a simpler design based on a generic black-box random position generator.

An Exploration of the Relationship between Improvements in Energy Efficiency and Life-Cycle Energy and Carbon Emissions using the BIRDS Low-Energy Residential Database.

PubMed

Kneifel, Joshua; O'Rear, Eric; Webb, David; O'Fallon, Cheyney

2018-02-01

To conduct a more complete analysis of low-energy and net-zero energy buildings that considers both the operating and embodied energy/emissions, members of the building community look to life-cycle assessment (LCA) methods. This paper examines differences in the relative impacts of cost-optimal energy efficiency measure combinations depicting residential buildings up to and beyond net-zero energy consumption on operating and embodied flows using data from the Building Industry Reporting and Design for Sustainability (BIRDS) Low-Energy Residential Database. Results indicate that net-zero performance leads to a large increase in embodied flows (over 40%) that offsets some of the reductions in operational flows, but overall life-cycle flows are still reduced by over 60% relative to the state energy code. Overall, building designs beyond net-zero performance can partially offset embodied flows with negative operational flows by replacing traditional electricity generation with solar production, but would require an additional 8.34 kW (18.54 kW in total) of due south facing solar PV to reach net-zero total life-cycle flows. Such a system would meet over 239% of operational consumption of the most energy efficient design considered in this study and over 116% of a state code-compliant building design in its initial year of operation.

ATES/heat pump simulations performed with ATESSS code

NASA Astrophysics Data System (ADS)

Vail, L. W.

1989-01-01

Modifications to the Aquifer Thermal Energy Storage System Simulator (ATESSS) allow simulation of aquifer thermal energy storage (ATES)/heat pump systems. The heat pump algorithm requires a coefficient of performance (COP) relationship of the form: COP = COP sub base + alpha (T sub ref minus T sub base). Initial applications of the modified ATES code to synthetic building load data for two sizes of buildings in two U.S. cities showed insignificant performance advantage of a series ATES heat pump system over a conventional groundwater heat pump system. The addition of algorithms for a cooling tower and solar array improved performance slightly. Small values of alpha in the COP relationship are the principal reason for the limited improvement in system performance. Future studies at Pacific Northwest Laboratory (PNL) are planned to investigate methods to increase system performance using alternative system configurations and operations scenarios.

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toprak, A. Emre; Guelay, F. Guelten; Ruge, Peter

2008-07-08

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performedmore » on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 mx7.80 m = 127.90 m{sup 2} with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher than the requirements of the Turkish Earthquake Code while the selected ground conditions represent the same characteristics. The main reason is that the ordinate of the horizontal elastic response spectrum for Eurocode 8 is increased by the soil factor. In TEC'07 force-based linear assessment, the seismic demands at cross-sections are to be checked with residual moment capacities; however, the chord rotations of primary ductile elements must be checked for Eurocode safety verifications. On the other hand, the demand curvatures from linear methods of analysis of Eurocode 8 together with TEC'07 are almost similar.« less

40 CFR 62.14105 - Requirements for municipal waste combustor operator training and certification.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Mutual Building, Room 540, 411 West Chapel Hill Street, Durham, NC 27701 or at the National Archives and...-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html... Hill Street, Durham, NC 27701 or at the National Archives and Records Administration (NARA). For...

40 CFR 62.14105 - Requirements for municipal waste combustor operator training and certification.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Mutual Building, Room 540, 411 West Chapel Hill Street, Durham, NC 27701 or at the National Archives and...-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html... Hill Street, Durham, NC 27701 or at the National Archives and Records Administration (NARA). For...

40 CFR 62.14105 - Requirements for municipal waste combustor operator training and certification.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Mutual Building, Room 540, 411 West Chapel Hill Street, Durham, NC 27701 or at the National Archives and...-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html... Hill Street, Durham, NC 27701 or at the National Archives and Records Administration (NARA). For...

40 CFR 62.14105 - Requirements for municipal waste combustor operator training and certification.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Mutual Building, Room 540, 411 West Chapel Hill Street, Durham, NC 27701 or at the National Archives and...-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html... Hill Street, Durham, NC 27701 or at the National Archives and Records Administration (NARA). For...

Application of the Life Safety Code to a Historic Test Stand

NASA Technical Reports Server (NTRS)

Askins, Bruce; Lemke, Paul R.; Lewis, William L.; Covell, Carol C.

2011-01-01

NASA has conducted a study to assess alternatives to refurbishing existing launch vehicle modal test facilities as opposed to developing new test facilities to meet the demands of a very fiscally constrained test and evaluation environment. The results of this study showed that Marshall Space Flight Center (MSFC) Test Stand (TS) 4550 could be made compliant, within reasonable cost and schedule impacts, if safety processes and operational limitations were put in place to meet the safety codes and concerns of the Fire Marshall. Trades were performed with key selection criteria to ensure that appropriate levels of occupant safety are incorporated into test facility design modifications. In preparation for the ground vibration tests that were to be performed on the Ares I launch vehicle, the Ares Flight and Integrated Test Office (FITO) organization evaluated the available test facility options, which included the existing mothballed structural dynamic TS4550 used by Apollo and Shuttle, alternative ground vibration test facilities at other locations, and construction of a new dynamic test stand. After an exhaustive assessment of the alternatives, the results favored modifying the TS4550 because it was the lowest cost option and presented the least schedule risk to the NASA Constellation Program for Ares Integrated Vehicle Ground Vibration Test (IVGVT). As the renovation design plans and drawings were being developed for TS4550, a safety concern was discovered the original design for the construction of the test stand, originally built for the Apollo Program and renovated for the Shuttle Program, was completed before NASA s adoption of the currently imposed safety and building codes per National Fire Protection Association Life Safety Code [NFPA 101] and International Building Codes. The initial FITO assessment of the design changes, required to make TS4550 compliant with current safety and building standards, identified a significant cost increase and schedule impact. An effort was launched to thoroughly evaluate the applicable life safety requirements, examine the context in which they were derived, and determine a means by which the TS4550 modifications could be made within budget and on schedule, while still providing the occupants with appropriate levels of safety.

Predicting the seismic performance of typical R/C healthcare facilities: emphasis on hospitals

NASA Astrophysics Data System (ADS)

Bilgin, Huseyin; Frangu, Idlir

2017-09-01

Reinforced concrete (RC) type of buildings constitutes an important part of the current building stock in earthquake prone countries such as Albania. Seismic response of structures during a severe earthquake plays a vital role in the extent of structural damage and resulting injuries and losses. In this context, this study evaluates the expected performance of a five-story RC healthcare facility, representative of common practice in Albania, designed according to older codes. The design was based on the code requirements used in this region during the mid-1980s. Non-linear static and dynamic time history analyses were conducted on the structural model using the Zeus NL computer program. The dynamic time history analysis was conducted with a set of ground motions from real earthquakes. The building responses were estimated in global levels. FEMA 356 criteria were used to predict the seismic performance of the building. The structural response measures such as capacity curve and inter-story drift under the set of ground motions and pushover analyses results were compared and detailed seismic performance assessment was done. The main aim of this study is considering the application and methodology for the earthquake performance assessment of existing buildings. The seismic performance of the structural model varied significantly under different ground motions. Results indicate that case study building exhibit inadequate seismic performance under different seismic excitations. In addition, reasons for the poor performance of the building is discussed.

Design of neurophysiologically motivated structures of time-pulse coded neurons

NASA Astrophysics Data System (ADS)

Krasilenko, Vladimir G.; Nikolsky, Alexander I.; Lazarev, Alexander A.; Lobodzinska, Raisa F.

2009-04-01

The common methodology of biologically motivated concept of building of processing sensors systems with parallel input and picture operands processing and time-pulse coding are described in paper. Advantages of such coding for creation of parallel programmed 2D-array structures for the next generation digital computers which require untraditional numerical systems for processing of analog, digital, hybrid and neuro-fuzzy operands are shown. The optoelectronic time-pulse coded intelligent neural elements (OETPCINE) simulation results and implementation results of a wide set of neuro-fuzzy logic operations are considered. The simulation results confirm engineering advantages, intellectuality, circuit flexibility of OETPCINE for creation of advanced 2D-structures. The developed equivalentor-nonequivalentor neural element has power consumption of 10mW and processing time about 10...100us.

Child Care Services and the NYS Uniform Fire Prevention and Building Code: A Building Code Examination of Child Day Care Services Which Are Regulated by the NYS Department of Social Services with Particular Attention to Day Care Centers and the Role of the Local Authority Having Jurisdiction.

ERIC Educational Resources Information Center

New York State Div. of Code Enforcement and Administration, Albany.

This course manual details the Uniform Fire Prevention and Building Code of New York State and how it affects child care services, particularly day care centers. The sections of the manual, each detailing a part of the code, are: (1) Introduction, Scope, Registration, and Definitions and Facilities Regulated by the New York Department of Social…

Building Energy Efficiency in India: Compliance Evaluation of Energy Conservation Building Code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Evans, Meredydd; Delgado, Alison

India is experiencing unprecedented construction boom. The country doubled its floorspace between 2001 and 2005 and is expected to add 35 billion m2 of new buildings by 2050. Buildings account for 35% of total final energy consumption in India today, and building energy use is growing at 8% annually. Studies have shown that carbon policies will have little effect on reducing building energy demand. Chaturvedi et al. predicted that, if there is no specific sectoral policies to curb building energy use, final energy demand of the Indian building sector will grow over five times by the end of this century,more » driven by rapid income and population growth. The growing energy demand in buildings is accompanied by a transition from traditional biomass to commercial fuels, particularly an increase in electricity use. This also leads to a rapid increase in carbon emissions and aggravates power shortage in India. Growth in building energy use poses challenges to the Indian government. To curb energy consumption in buildings, the Indian government issued the Energy Conservation Building Code (ECBC) in 2007, which applies to commercial buildings with a connected load of 100 kW or 120kVA. It is predicted that the implementation of ECBC can help save 25-40% of energy, compared to reference buildings without energy-efficiency measures. However, the impact of ECBC depends on the effectiveness of its enforcement and compliance. Currently, the majority of buildings in India are not ECBC-compliant. The United Nations Development Programme projected that code compliance in India would reach 35% by 2015 and 64% by 2017. Whether the projected targets can be achieved depends on how the code enforcement system is designed and implemented. Although the development of ECBC lies in the hands of the national government – the Bureau of Energy Efficiency under the Ministry of Power, the adoption and implementation of ECBC largely relies on state and local governments. Six years after ECBC’s enactment, only two states and one territory out of 35 Indian states and union territories formally adopted ECBC and six additional states are in the legislative process of approving ECBC. There are several barriers that slow down the process. First, stakeholders, such as architects, developers, and state and local governments, lack awareness of building energy efficiency, and do not have enough capacity and resources to implement ECBC. Second, institution for implementing ECBC is not set up yet; ECBC is not included in local building by-laws or incorporated into the building permit process. Third, there is not a systematic approach to measuring and verifying compliance and energy savings, and thus the market does not have enough confidence in ECBC. Energy codes achieve energy savings only when projects comply with codes, yet only few countries measure compliance consistently and periodic checks often indicate poor compliance in many jurisdictions. China and the U.S. appear to be two countries with comprehensive systems in code enforcement and compliance The United States recently developed methodologies measuring compliance with building energy codes at the state level. China has an annual survey investigating code compliance rate at the design and construction stages in major cities. Like many developing countries, India has only recently begun implementing an energy code and would benefit from international experience on code compliance. In this paper, we examine lessons learned from the U.S. and China on compliance assessment and how India can apply these lessons to develop its own compliance evaluation approach. This paper also provides policy suggestions to national, state, and local governments to improve compliance and speed up ECBC implementation.« less

Improving building energy efficiency in India: State-level analysis of building energy efficiency policies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Tan, Qing; Evans, Meredydd

India is expected to add 40 billion m2 of new buildings till 2050. Buildings are responsible for one third of India’s total energy consumption today and building energy use is expected to continue growing driven by rapid income and population growth. The implementation of the Energy Conservation Building Code (ECBC) is one of the measures to improve building energy efficiency. Using the Global Change Assessment Model, this study assesses growth in the buildings sector and impacts of building energy policies in Gujarat, which would help the state adopt ECBC and expand building energy efficiency programs. Without building energy policies, buildingmore » energy use in Gujarat would grow by 15 times in commercial buildings and 4 times in urban residential buildings between 2010 and 2050. ECBC improves energy efficiency in commercial buildings and could reduce building electricity use in Gujarat by 20% in 2050, compared to the no policy scenario. Having energy codes for both commercial and residential buildings could result in additional 10% savings in electricity use. To achieve these intended savings, it is critical to build capacity and institution for robust code implementation.« less

28 CFR 36.601 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.601... means a State law or local building code or similar ordinance, or part thereof, that establishes... designee. Certification of equivalency means a final certification that a code meets or exceeds the minimum...

28 CFR 36.601 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.601... means a State law or local building code or similar ordinance, or part thereof, that establishes... designee. Certification of equivalency means a final certification that a code meets or exceeds the minimum...

28 CFR 36.601 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.601... means a State law or local building code or similar ordinance, or part thereof, that establishes... designee. Certification of equivalency means a final certification that a code meets or exceeds the minimum...

A comparison of IBC with 1997 UBC for modal response spectrum analysis in standard-occupancy buildings

NASA Astrophysics Data System (ADS)

Nahhas, Tariq M.

2011-03-01

This paper presents a comparison of the seismic forces generated from a Modal Response Spectrum Analysis (MRSA) by applying the provisions of two building codes, the 1997 Uniform Building Code (UBC) and the 2000-2009 International Building Code (IBC), to the most common ordinary residential buildings of standard occupancy. Considering IBC as the state of the art benchmark code, the primary concern is the safety of buildings designed using the UBC as compared to those designed using the IBC. A sample of four buildings with different layouts and heights was used for this comparison. Each of these buildings was assumed to be located at four different geographical sample locations arbitrarily selected to represent various earthquake zones on a seismic map of the USA, and was subjected to code-compliant response spectrum analyses for all sample locations and for five different soil types at each location. Response spectrum analysis was performed using the ETABS software package. For all the cases investigated, the UBC was found to be significantly more conservative than the IBC. The UBC design response spectra have higher spectral accelerations, and as a result, the response spectrum analysis provided a much higher base shear and moment in the structural members as compared to the IBC. The conclusion is that ordinary office and residential buildings designed using UBC 1997 are considered to be overdesigned, and therefore they are quite safe even according to the IBC provisions.

Determining Position Inside Non-industrial Buildings Using Ultrasound Transducers

PubMed Central

Escudero, Francesc; Margalef, Jordi; Luengo, Sonia; Alsina, Maria; Ribes, Josep M.; Pérez, Juan

2007-01-01

The position determination inside a building where no GPS signal is being received can be ascertained using laser transmitters in industrial situations where there are no people or using triangulation of the signal strength, normally electro-magnetic signals, if the required accuracy is more than a metre. Our solution is aimed at situations where people are present and where the required accuracy is less than 30 cm, such as in shopping precincts or supermarkets. To achieve this, a network of ultrasonic transmitters is fitted into the ceiling which receives a synchronised time signal. Each transmitter has a unique identifier code and emits its code with a delay with respect to the common time signal which is proportional to its code number with an ASK modulation over the ultrasonic band centred on 40 KHz. The receivers circulating beneath the transmitters receive the codes of those within their detection range, translate the time delays into distances and then obtain their position by triangulation since the receivers know the position of every transmitter. Since the receivers are not synchronised with the common time signal or the actual speed of the sound, whose value varies appreciably with temperature, relative humidity and atmospheric pressure, a consecutive approximation algorithm has been introduced. This is based on the fact that the Z coordinator of the receiver is known and constant and thus it is possible, with only three different identifiers received, to deduce the phase of the common time signal and estimate the speed of the sound with a fourth identifier. PMID:28903247

A proposal for seismic evaluation index of mid-rise existing RC buildings in Afghanistan

NASA Astrophysics Data System (ADS)

Naqi, Ahmad; Saito, Taiki

2017-10-01

Mid-rise RC buildings gradually rise in Kabul and entire Afghanistan since 2001 due to rapid increase of population. To protect the safety of resident, Afghan Structure Code was issued in 2012. But the building constructed before 2012 failed to conform the code requirements. In Japan, new sets of rules and law for seismic design of buildings had been issued in 1981 and severe earthquake damage was disclosed for the buildings designed before 1981. Hence, the Standard for Seismic Evaluation of RC Building published in 1977 has been widely used in Japan to evaluate the seismic capacity of existing buildings designed before 1981. Currently similar problem existed in Afghanistan, therefore, this research examined the seismic capacity of six RC buildings which were built before 2012 in Kabul by applying the seismic screening procedure presented by Japanese standard. Among three screening procedures with different capability, the less detailed screening procedure, the first level of screening, is applied. The study founds an average seismic index (IS-average=0.21) of target buildings. Then, the results were compared with those of more accurate seismic evaluation procedures of Capacity Spectrum Method (CSM) and Time History Analysis (THA). The results for CSM and THA show poor seismic performance of target buildings not able to satisfy the safety design limit (1/100) of the maximum story drift. The target buildings are then improved by installing RC shear walls. The seismic indices of these retrofitted buildings were recalculated and the maximum story drifts were analyzed by CSM and THA. The seismic indices and CSM and THA results are compared and found that building with seismic index larger than (IS-average =0.4) are able to satisfy the safety design limit. Finally, to screen and minimize the earthquake damage over the existing buildings, the judgement seismic index (IS-Judgment=0.5) for the first level of screening is proposed.

28 CFR 36.607 - Effect of certification.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... the question of whether equipment in a building built according to the code satisfies the Act's... equivalency only with respect to those features or elements that are both covered by the certified code and...

Site 300 Spill Prevention, Control, and Countermeasures (SPCC) Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, D.; Mertesdorf, E.

This Spill Prevention, Control, and Countermeasure (SPCC) Plan describes the measures that are taken at Lawrence Livermore National Laboratory’s (LLNL) Experimental Test Site (Site 300) near Tracy, California, to prevent, control, and handle potential spills from aboveground containers that can contain 55 gallons or more of oil. This SPCC Plan complies with the Oil Pollution Prevention regulation in Title 40 of the Code of Federal Regulations, Part 112 (40 CFR 112) and with 40 CFR 761.65(b) and (c), which regulates the temporary storage of polychlorinated biphenyls (PCBs). This Plan has also been prepared in accordance with Division 20, Chapter 6.67more » of the California Health and Safety Code (HSC 6.67) requirements for oil pollution prevention (referred to as the Aboveground Petroleum Storage Act [APSA]), and the United States Department of Energy (DOE) Order No. 436.1. This SPCC Plan establishes procedures, methods, equipment, and other requirements to prevent the discharge of oil into or upon the navigable waters of the United States or adjoining shorelines for aboveground oil storage and use at Site 300. This SPCC Plan has been prepared for the entire Site 300 facility and replaces the three previous plans prepared for Site 300: LLNL SPCC for Electrical Substations Near Buildings 846 and 865 (LLNL 2015), LLNL SPCC for Building 883 (LLNL 2015), and LLNL SPCC for Building 801 (LLNL 2014).« less

Site 300 SPCC Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, D.

This Spill Prevention, Control, and Countermeasure (SPCC) Plan describes the measures that are taken at Lawrence Livermore National Laboratory’s (LLNL) Experimental Test Site (Site 300) near Tracy, California, to prevent, control, and handle potential spills from aboveground containers that can contain 55 gallons or more of oil. This SPCC Plan complies with the Oil Pollution Prevention regulation in Title 40 of the Code of Federal Regulations, Part 112 (40 CFR 112) and with 40 CFR 761.65(b) and (c), which regulates the temporary storage of polychlorinated biphenyls (PCBs). This Plan has also been prepared in accordance with Division 20, Chapter 6.67more » of the California Health and Safety Code (HSC 6.67) requirements for oil pollution prevention (referred to as the Aboveground Petroleum Storage Act [APSA]), and the United States Department of Energy (DOE) Order No. 436.1. This SPCC Plan establishes procedures, methods, equipment, and other requirements to prevent the discharge of oil into or upon the navigable waters of the United States or adjoining shorelines for aboveground oil storage and use at Site 300. This SPCC Plan has been prepared for the entire Site 300 facility and replaces the three previous plans prepared for Site 300: LLNL SPCC for Electrical Substations Near Buildings 846 and 865 (LLNL 2015), LLNL SPCC for Building 883 (LLNL 2015), and LLNL SPCC for Building 801 (LLNL 2014).« less

Data on European non-residential buildings.

PubMed

D'Agostino, Delia; Cuniberti, Barbara; Bertoldi, Paolo

2017-10-01

This data article relates to the research paper Energy consumption and efficiency technology measures in European non-residential buildings (D'Agostino et al., 2017) [1]. The reported data have been collected in the framework of the Green Building Programme that ran from 2006 to 2014. The project has encouraged the adoption of efficiency measures to boost energy savings in European non-residential buildings. Data focus on the one-thousand buildings that joined the Programme allowing to save around 985 GWh/year. The main requirement to join the Programme was the reduction of at least 25% primary energy consumption in a new or retrofitted building. Energy consumption before and after the renovation are provided for retrofitted buildings while, in new constructions, a building had to be designed using at least 25% less energy than requested by the country's building codes. The following data are linked within this article: energy consumption, absolute and relative savings related to primary energy, saving percentages, implemented efficiency measures and renewables. Further information is given about each building in relation to geometry, envelope, materials, lighting and systems.

Active Fault Near-Source Zones Within and Bordering the State of California for the 1997 Uniform Building Code

USGS Publications Warehouse

Petersen, M.D.; Toppozada, Tousson R.; Cao, T.; Cramer, C.H.; Reichle, M.S.; Bryant, W.A.

2000-01-01

The fault sources in the Project 97 probabilistic seismic hazard maps for the state of California were used to construct maps for defining near-source seismic coefficients, Na and Nv, incorporated in the 1997 Uniform Building Code (ICBO 1997). The near-source factors are based on the distance from a known active fault that is classified as either Type A or Type B. To determine the near-source factor, four pieces of geologic information are required: (1) recognizing a fault and determining whether or not the fault has been active during the Holocene, (2) identifying the location of the fault at or beneath the ground surface, (3) estimating the slip rate of the fault, and (4) estimating the maximum earthquake magnitude for each fault segment. This paper describes the information used to produce the fault classifications and distances.

Reaction-to-fire testing and modeling for wood products

Treesearch

Mark A. Dietenberger; Robert H. White

2001-01-01

In this review we primarily discuss our use of the oxygen consumption calorimeter (ASTM E1354 for cone calorimeter and ISO9705 for room/corner tests) and fire growth modeling to evaluate treated wood products. With recent development towards performance-based building codes, new methodology requires engineering calculations of various fire growth scenarios. The initial...

7 CFR Exhibit I to Subpart A of... - Guidelines for Seasonal Farm Labor Housing

Code of Federal Regulations, 2013 CFR

2013-01-01

... convertible to year-round occupancy; however, the living units shall be designed for the intended type of... is important that the design of the LH site and buildings will help to create a pleasing lifestyle...—Compliance is required with National, state and local codes or regulations affecting design, construction...

HIGH RISE OR LOW RISE. A STUDY OF DECISION FACTORS IN RESIDENCE HALLS PLANNING.

ERIC Educational Resources Information Center

Educational Facilities Labs., Inc., New York, NY.

THE PURPOSE OF THIS REPORT IS TO SERVE COLLEGE OFFICIALS, HOUSING ADMINISTRATORS, PLANNING GROUPS AND ARCHITECTS BY FOCUSING ON THE DECISION FACTORS WHICH RELATE TO HIGH-RISE AND LOW-RISE STUDENT HOUSING. DECISION FACTORS INCLUDE--(1) LAND USE IMPLICATIONS, (2) SITE REQUIREMENTS--BUILDING CODES, SUB-SOIL CONSIDERATIONS, NATURAL TERRAIN,…

A Pictorial History of the Code 717 Unmanned Systems Group: Air, Land, and Sea. Volume 1: 1970-1999

DTIC Science & Technology

2016-04-28

requirements. 54 a) b) Figure 67. a) Site preparation for Building 585 began with demolition of the foundation for the oil -well derrick...Proceedings of the 9th International Conference on Informatics in Control, Automation and Robotics (ICINCO). 28–31 July, Rome, Italy. Pransky, J. 1997

Rooftop Solar Technical Potential for Low-to-Moderate Income Households in

Science.gov Websites

communities. A map of the United States, divided by county, is color-coded by the total solar technical of LMI households in the U.S. (approximately 43 percent), this analysis reveals two other important city governments, though to do so requires deployment on multi-family and renter-occupied buildings

Software Measurement Guidebook. Version 02.00.02

DTIC Science & Technology

1992-12-01

Compatibility Testing Process .............................. 9-5 Figure 9-3. Development Effort Planning Curve ................................. 9-7 Figure 10-1...requirements, design, code, and test and for analyzing this data. "* Proposal Manager. The person responsible for describing and supporting the estimated...designed, build/elease ranges, variances, and comparisons size growth; costs; completions; and content, units completing test , units with historical

76 FR 64924 - Updating State Residential Building Energy Efficiency Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-19

...) considers high-rise (greater than three stories) multifamily residential buildings and hotel, motel, and..., duplexes, townhouses, row houses, and low-rise multifamily buildings (not greater than three stories) such... pumps as compared to other electric heating technologies, this code change is expected to increase the...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richer, Jeff; Frimeth, Jeff; Nesbitt, James

Purpose: In Ontario, shielding for all X-ray machines, including CT scanners, must be evaluated according to Safety Code 20A (Health Canada, 1983) which is based on NCRP-49 (NCRP, 1976). NCRP-147 (NCRP, 2004) is the international standard for shielding calculations of CT scanners and is also referenced in Safety Code 35 (Health Canada, 2008) which, was published to supersede SC20A. The goal of this work is to demonstrate the cost effectiveness of NCRP-147 for CT scanner shielding. Methods: CT scanner shielding calculations are performed using SC20A and NCRP-147: A room located on the third floor with the nearest building 75m awaymore » A room with high occupancy uncontrolled adjacent spaces Two side by side rooms on the main floor Results: 1. SC20A: The exterior windows required 0.1mm of Pb to protect the public who may occupy the building at 75m. 1. NCRP-147: No additional shielding required. 2. SC20A: Two walls adjacent to high occupancy uncontrolled space required an additional 1.58mm Pb. 2. NCRP-147: No additional shielding required. 3. SC20A: The entire floor and ceiling slabs in both rooms required an additional 0.79mm Pb. In addition, 0.79mm Pb was added to the walls from the ceiling to overlap the existing Pb shielding in the walls. 3. NCRP-147: No additional shielding required. Conclusion: The application of NCRP Report No. 147 affords the required protection to staff and the public, in the true spirit of the ALARA principle, taking into account relevant social and economic factors.« less

42 CFR 137.328 - Must a construction project proposal incorporate provisions of Federal construction guidelines...

Code of Federal Regulations, 2014 CFR

2014-10-01

..., the Self-Governance Tribe and the Secretary must agree upon and specify appropriate building codes and...-Governance Tribe in the preparation of its construction project proposal. If Tribal construction codes and standards (including national, regional, State, or Tribal building codes or construction industry standards...

42 CFR 137.328 - Must a construction project proposal incorporate provisions of Federal construction guidelines...

Code of Federal Regulations, 2012 CFR

2012-10-01

..., the Self-Governance Tribe and the Secretary must agree upon and specify appropriate building codes and...-Governance Tribe in the preparation of its construction project proposal. If Tribal construction codes and standards (including national, regional, State, or Tribal building codes or construction industry standards...

42 CFR 137.328 - Must a construction project proposal incorporate provisions of Federal construction guidelines...

Code of Federal Regulations, 2013 CFR

2013-10-01

..., the Self-Governance Tribe and the Secretary must agree upon and specify appropriate building codes and...-Governance Tribe in the preparation of its construction project proposal. If Tribal construction codes and standards (including national, regional, State, or Tribal building codes or construction industry standards...

42 CFR 137.328 - Must a construction project proposal incorporate provisions of Federal construction guidelines...

Code of Federal Regulations, 2011 CFR

2011-10-01

..., the Self-Governance Tribe and the Secretary must agree upon and specify appropriate building codes and...-Governance Tribe in the preparation of its construction project proposal. If Tribal construction codes and standards (including national, regional, State, or Tribal building codes or construction industry standards...

42 CFR 137.328 - Must a construction project proposal incorporate provisions of Federal construction guidelines...

Code of Federal Regulations, 2010 CFR

2010-10-01

..., the Self-Governance Tribe and the Secretary must agree upon and specify appropriate building codes and...-Governance Tribe in the preparation of its construction project proposal. If Tribal construction codes and standards (including national, regional, State, or Tribal building codes or construction industry standards...

a Framework for Distributed Mixed Language Scientific Applications

NASA Astrophysics Data System (ADS)

Quarrie, D. R.

The Object Management Group has defined an architecture (CORBA) for distributed object applications based on an Object Request Broker and Interface Definition Language. This project builds upon this architecture to establish a framework for the creation of mixed language scientific applications. A prototype compiler has been written that generates FORTRAN 90 or Eiffel stubs and skeletons and the required C++ glue code from an input IDL file that specifies object interfaces. This generated code can be used directly for non-distributed mixed language applications or in conjunction with the C++ code generated from a commercial IDL compiler for distributed applications. A feasibility study is presently underway to see whether a fully integrated software development environment for distributed, mixed-language applications can be created by modifying the back-end code generator of a commercial CASE tool to emit IDL.

7 CFR 1792.102 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... property will rank below the lien of another entity. Model Code—A building code developed for the adoption of local or state authorities or to be used as the basis of a local or state building code. NEHRP... Federally Assisted New Building Construction § 1792.102 Definitions. As used in this subpart, the following...

7 CFR 1792.102 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... property will rank below the lien of another entity. Model Code—A building code developed for the adoption of local or state authorities or to be used as the basis of a local or state building code. NEHRP... Federally Assisted New Building Construction § 1792.102 Definitions. As used in this subpart, the following...

7 CFR 1792.102 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... property will rank below the lien of another entity. Model Code—A building code developed for the adoption of local or state authorities or to be used as the basis of a local or state building code. NEHRP... Federally Assisted New Building Construction § 1792.102 Definitions. As used in this subpart, the following...

7 CFR 1792.102 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... property will rank below the lien of another entity. Model Code—A building code developed for the adoption of local or state authorities or to be used as the basis of a local or state building code. NEHRP... Federally Assisted New Building Construction § 1792.102 Definitions. As used in this subpart, the following...

7 CFR 1792.102 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... property will rank below the lien of another entity. Model Code—A building code developed for the adoption of local or state authorities or to be used as the basis of a local or state building code. NEHRP... Federally Assisted New Building Construction § 1792.102 Definitions. As used in this subpart, the following...

Evaluation of fault-normal/fault-parallel directions rotated ground motions for response history analysis of an instrumented six-story building

USGS Publications Warehouse

Kalkan, Erol; Kwong, Neal S.

2012-01-01

According to regulatory building codes in United States (for example, 2010 California Building Code), at least two horizontal ground-motion components are required for three-dimensional (3D) response history analysis (RHA) of buildings. For sites within 5 km of an active fault, these records should be rotated to fault-normal/fault-parallel (FN/FP) directions, and two RHA analyses should be performed separately (when FN and then FP are aligned with the transverse direction of the structural axes). It is assumed that this approach will lead to two sets of responses that envelope the range of possible responses over all nonredundant rotation angles. This assumption is examined here using a 3D computer model of a six-story reinforced-concrete instrumented building subjected to an ensemble of bidirectional near-fault ground motions. Peak responses of engineering demand parameters (EDPs) were obtained for rotation angles ranging from 0° through 180° for evaluating the FN/FP directions. It is demonstrated that rotating ground motions to FN/FP directions (1) does not always lead to the maximum responses over all angles, (2) does not always envelope the range of possible responses, and (3) does not provide maximum responses for all EDPs simultaneously even if it provides a maximum response for a specific EDP.

Comparisons of four computer models with experimental data from test buildings in northern New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, D.K.; Christian, J.E.

1985-01-01

Eight one-room test buildings, 20 ft (6.1 m) square and 7.5 ft (2.3 m) high, were constructed on a high desert site near Tesuque Pueblo, New Mexico, to study the influence of wall dynamic heat transfer characteristics on building heating requirements (the ''thermal mass effect''). The buildings are nominally identical except for the walls (adobe, concrete and masonry unit, wood-frame, and log) and are constructed so as to isolate the effects of the walls. The amount of mass in the walls varies from 240 lb/ft/sup 2/ (1171 kg/m/sup 2/) for the 2 ft (.61 m) thick adobe wall to 4.3more » lb/ft/sup 2/ (21 kg/m/sup 2/) for the insulated wood-frame wall. The roof, floor, and stem walls are all well insulated and the buildings were constructed with infiltration rates less than 0.4 air change per hour. The site is instrumented to record building component temperatures and heat fluxes, outside weather conditions, and heating energy use. Data were collected for two heating seasons from midwinter to late spring with the buildings in two configurations, with and without windows. Four computer codes were used to simulate the performance of the test buildings without windows, using site weather data. The codes used were DOE-2.1A, DOE-2.1C, BLAST, and DEROB. Each code was run by a different analyst. Simulations were done for midwinter, late winter, and spring. Two of the test cell comparisons are discussed; the insulated frame and an 11-in. (.28 m) adobe. This work presents a quantitative and qualitative critical comparison of the modeling and experimental results. Cumulative heating loads, wall heat fluxes, and air surface temperatures are compared, as well as input assumptions to the models. Explanations of differences and difficulties encountered are reported. The principal findings were that cumulative heating loads and the characteristic influences of wall thermal mass on hourly behavior were reproduced by the models.« less

New "Risk-Targeted" Seismic Maps Introduced into Building Codes

USGS Publications Warehouse

Luco, Nicholas; Garrett, B.; Hayes, J.

2012-01-01

Throughout most municipalities of the United States, structural engineers design new buildings using the U.S.-focused International Building Code (IBC). Updated editions of the IBC are published every 3 years. The latest edition (2012) contains new "risk-targeted maximum considered earthquake" (MCER) ground motion maps, which are enabling engineers to incorporate a more consistent and better defined level of seismic safety into their building designs.

Building an effective corporate compliance plan.

PubMed

Ryan, E

1997-09-01

Corporate compliance plans are essential for healthcare organizations to cope with, and perhaps even stave off, investigations arising from allegations of illegal business practices. Initial development and implementation of a corporate compliance plan can be facilitated through four steps: determining the content of the code of conduct, determining how the code will be distributed, assigning responsibility for implementing the plan, and appointing a compliance task force to guide the implementation process. Special attention should be paid to education requirements of the United States Sentencing Guidelines to see that all employees understand and can apply provisions of the plan.

Pinoleville Pomo Nation Tribal Green Building Code

EPA Pesticide Factsheets

The Pinoleville Pomo Nation (PPN) worked with the U.S. Environmental Protection Agency (EPA) and the Development Center for Appropriate Technology (DCAT) to create this framework for tribal building codes.

Deregulation of the Building Code and the Norwegian Approach to Regulation of Accessibility in the Built Environment.

PubMed

Lyngstad, Pål

2016-01-01

Deregulation is on the political agenda in the European countries. The Norwegian building code related to universal design and accessibility is challenged. To meet this, the Norwegian Building Authority have chosen to examine established truths and are basing their revised code on scientific research and field tests. But will this knowledge-based deregulation comply within the framework of the anti-discrimination act and, and if not: who suffers and to what extent?

Inclusion of cool roofs in nonresidential Title 24 prescriptive requirements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levinson, Ronnen; Akbari, Hashem; Konopacki, Steve

2002-12-15

Roofs that have high solar reflectance (high ability to reflect sunlight) and high thermal emittance (high ability to radiate heat) tend to stay cool in the sun. The same is true of low-emittance roofs with exceptionally high solar reflectance. Substituting a cool roof for a noncool roof tends to decrease cooling electricity use, cooling power demand, and cooling-equipment capacity requirements, while slightly increasing heating energy consumption. Cool roofs can also lower the ambient air temperature in summer, slowing ozone formation and increasing human comfort. DOE-2.1E building energy simulations indicate that use of a cool roofing material on a prototypical Californiamore » nonresidential building with a low-sloped roof yields average annual cooling energy savings of approximately 300 kWh/1000 ft2 [3.2 kWh/m2], average annual natural gas deficits of 4.9 therm/1000 ft2 [5.6 MJ/m2], average source energy savings of 2.6 MBTU/1000 ft2 [30 MJ/m2], and average peak power demand savings of 0. 19 kW/1000 ft2 [2.1 W/m2]. The 15-year net present value (NPV) of energy savings averages $450/1000 ft2 [$4.90/m2] with time dependent valuation (TDV), and $370/1000 ft2 [$4.00/m2] without TDV. When cost savings from downsizing cooling equipment are included, the average total savings (15-year NPV + equipment savings) rises to $550/1000 ft2 [$5.90/m2] with TDV, and to $470/1000 ft2 [$5.00/m2] without TDV. Total savings range from 0.18 to 0.77 $/ft2 [1.90 to 8.30 $/m2] with TDV, and from 0.16 to 0.66 $/ft2 [1.70 to 7.10 $/m2] without TDV, across California's 16 climate zones. The typical cost premium for a cool roof is 0.00 to 0.20 $/ft2 [0.00 to 2.20 $/m2]. Cool roofs with premiums up to $0.20/ft2 [$2.20/m2] are expected to be cost effective in climate zones 2 through 16; those with premiums not exceeding $0.18/ft2 [$1.90/m2] are expected to be also cost effective in climate zone 1. Hence, this study recommends that the year-2005 California building energy efficiency code (Title 24, Pa rt 6 of the California Code of Regulations) for nonresidential buildings with low-sloped roofs include a cool-roof prescriptive requirement in all California climate zones. Buildings with roofs that do not meet prescriptive requirements may comply with the code via an ''overall-envelope'' approach (non-metal roofs only), or via a performance approach (all roof types).« less

Energy Efficiency Program Administrators and Building Energy Codes

EPA Pesticide Factsheets

Explore how energy efficiency program administrators have helped advance building energy codes at federal, state, and local levels—using technical, institutional, financial, and other resources—and discusses potential next steps.

Critical evaluation of reverse engineering tool Imagix 4D!

PubMed

Yadav, Rashmi; Patel, Ravindra; Kothari, Abhay

2016-01-01

The comprehension of legacy codes is difficult to understand. Various commercial reengineering tools are available that have unique working styles, and are equipped with their inherent capabilities and shortcomings. The focus of the available tools is in visualizing static behavior not the dynamic one. Therefore, it is difficult for people who work in software product maintenance, code understanding reengineering/reverse engineering. Consequently, the need for a comprehensive reengineering/reverse engineering tool arises. We found the usage of Imagix 4D to be good as it generates the maximum pictorial representations in the form of flow charts, flow graphs, class diagrams, metrics and, to a partial extent, dynamic visualizations. We evaluated Imagix 4D with the help of a case study involving a few samples of source code. The behavior of the tool was analyzed on multiple small codes and a large code gcc C parser. Large code evaluation was performed to uncover dead code, unstructured code, and the effect of not including required files at preprocessing level. The utility of Imagix 4D to prepare decision density and complexity metrics for a large code was found to be useful in getting to know how much reengineering is required. At the outset, Imagix 4D offered limitations in dynamic visualizations, flow chart separation (large code) and parsing loops. The outcome of evaluation will eventually help in upgrading Imagix 4D and posed a need of full featured tools in the area of software reengineering/reverse engineering. It will also help the research community, especially those who are interested in the realm of software reengineering tool building.

Expansion and improvements of the FORMA system for response and load analysis. Volume 1: Programming manual

NASA Technical Reports Server (NTRS)

Wohlen, R. L.

1976-01-01

Techniques are presented for the solution of structural dynamic systems on an electronic digital computer using FORMA (FORTRAN Matrix Analysis). FORMA is a library of subroutines coded in FORTRAN 4 for the efficient solution of structural dynamics problems. These subroutines are in the form of building blocks that can be put together to solve a large variety of structural dynamics problems. The obvious advantage of the building block approach is that programming and checkout time are limited to that required for putting the blocks together in the proper order.

NA-241_Quarterly Report_SBLibby - 12.31.2017_v2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Libby, Stephen B.

This is an evaluation of candidate navigation solutions for GPS free inspection tools that can be used in tours of large building interiors. In principle, COTS portable inertial motion unit (IMU) sensors with satisfactory accuracy, SWAP (size, weight, power), low error, and bias drift can provide sufficiently accurate dead reckoning navigation in a large building in the absence of GPS. To explore this assumption, the capabilities of representative IMU navigation sensors to meet these requirements will be evaluated, starting with a market survey, and then carrying out a basic analysis of these sensors using LLNL’s navigation codes.

Effectiveness of fire-retardant treatments for shingles after 10 years of outdoor weathering

Treesearch

S. L. LeVan; C. A. Holmes

Some building codes require wood shingles to be fire-retardant treated. Because exterior fire-retardant treatments are subjected to weathering, treatment durability and leach resistance are critical for insuring adequate fire protection. We examined the effectiveness of various fire-retardant treatments on wood after 0, 2, 5, and 10 years of outdoor exposure. We used a...

Fire endurance research at the Forest Products Laboratory

Treesearch

R. H. White

1990-01-01

Fire endurance research activities and facilities at the FPL concern the ability of a wood member or assembly to withstand the effects of fire while acting as a fire barrier and supporting a load. Fire endurance is generally concerned with the post-flashover portion of the fire. The importance of fire endurance in fire safety is reflected in building code requirements...

Strategies and Challenges for Energy Efficient Retrofitting: Study of the Empire State Building

NASA Astrophysics Data System (ADS)

De, B.; Mukherjee, M.

2013-11-01

Operational and maintenance cost of existing buildings is escalating making it tough for both the owner and the tenants. Retrofitting them with state of the art technologies help them to keep pace with amended recent code provisions and thus extending the older building stocks one more chance to live responsively. Retrofitted iconic buildings can thus retain their status in commerce driven real estate sector. It helps in reducing green house gas emission as well. World's iconic skyscraper, the Empire State Building (ESB), has undergone an exemplary retrofit process since 2008 to reduce its energy demands. To achieve the goal of operational cost and energy consumption reduction, stiff challenges had taken care in a systematic manner to realize benefit throughout the entire lifespan of the ESB. Least disturbances to the tenant and on-site component handling strategies required precise planning. The present paper explores strategies and process adopted for retrofitting the ESB, and derived insightful guidelines towards operational cost savings and energy efficiency of existing buildings through retrofitting.

Measure Guideline: Buried and/or Encapsulated Ducts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shapiro, C.; Zoeller, W.; Mantha, P.

2013-08-01

Buried and/or encapsulated ducts (BEDs) are a class of advanced, energy-efficiency strategies intended to address the significant ductwork thermal losses associated with ducts installed in unconditioned attics. BEDs are ducts installed in unconditioned attics that are covered in loose-fill insulation and/or encapsulated in closed cell polyurethane spray foam insulation. This Measure Guideline covers the technical aspects of BEDs as well as the advantages, disadvantages, and risks of BEDs compared to other alternative strategies. This guideline also provides detailed guidance on installation of BEDs strategies in new and existing homes through step-by-step installation procedures. This Building America Measure Guideline synthesizes previouslymore » published research on BEDs and provides practical information to builders, contractors, homeowners, policy analysts, building professions, and building scientists. Some of the procedures presented here, however, require specialized equipment or expertise. In addition, some alterations to duct systems may require a specialized license. Persons implementing duct system improvements should not go beyond their expertise or qualifications. This guideline provides valuable information for a building industry that has struggled to address ductwork thermal losses in new and existing homes. As building codes strengthen requirements for duct air sealing and insulation, flexibility is needed to address energy efficiency goals. While ductwork in conditioned spaces has been promoted as the panacea for addressing ductwork thermal losses, BEDs installations approach - and sometimes exceed - the performance of ductwork in conditioned spaces.« less

ClinicalCodes: an online clinical codes repository to improve the validity and reproducibility of research using electronic medical records.

PubMed

Springate, David A; Kontopantelis, Evangelos; Ashcroft, Darren M; Olier, Ivan; Parisi, Rosa; Chamapiwa, Edmore; Reeves, David

2014-01-01

Lists of clinical codes are the foundation for research undertaken using electronic medical records (EMRs). If clinical code lists are not available, reviewers are unable to determine the validity of research, full study replication is impossible, researchers are unable to make effective comparisons between studies, and the construction of new code lists is subject to much duplication of effort. Despite this, the publication of clinical codes is rarely if ever a requirement for obtaining grants, validating protocols, or publishing research. In a representative sample of 450 EMR primary research articles indexed on PubMed, we found that only 19 (5.1%) were accompanied by a full set of published clinical codes and 32 (8.6%) stated that code lists were available on request. To help address these problems, we have built an online repository where researchers using EMRs can upload and download lists of clinical codes. The repository will enable clinical researchers to better validate EMR studies, build on previous code lists and compare disease definitions across studies. It will also assist health informaticians in replicating database studies, tracking changes in disease definitions or clinical coding practice through time and sharing clinical code information across platforms and data sources as research objects.

ClinicalCodes: An Online Clinical Codes Repository to Improve the Validity and Reproducibility of Research Using Electronic Medical Records

PubMed Central

Springate, David A.; Kontopantelis, Evangelos; Ashcroft, Darren M.; Olier, Ivan; Parisi, Rosa; Chamapiwa, Edmore; Reeves, David

2014-01-01

Lists of clinical codes are the foundation for research undertaken using electronic medical records (EMRs). If clinical code lists are not available, reviewers are unable to determine the validity of research, full study replication is impossible, researchers are unable to make effective comparisons between studies, and the construction of new code lists is subject to much duplication of effort. Despite this, the publication of clinical codes is rarely if ever a requirement for obtaining grants, validating protocols, or publishing research. In a representative sample of 450 EMR primary research articles indexed on PubMed, we found that only 19 (5.1%) were accompanied by a full set of published clinical codes and 32 (8.6%) stated that code lists were available on request. To help address these problems, we have built an online repository where researchers using EMRs can upload and download lists of clinical codes. The repository will enable clinical researchers to better validate EMR studies, build on previous code lists and compare disease definitions across studies. It will also assist health informaticians in replicating database studies, tracking changes in disease definitions or clinical coding practice through time and sharing clinical code information across platforms and data sources as research objects. PMID:24941260

The international implications of national and local coordination on building energy codes: Case studies in six cities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Meredydd; Yu, Sha; Staniszewski, Aaron

Building energy efficiency is an important strategy for reducing greenhouse gas emissions globally. In fact, 55 countries have included building energy efficiency in their Nationally Determined Contributions (NDCs) under the Paris Agreement. This research uses building energy code implementation in six cities across different continents as case studies to assess what it may take for countries to implement the ambitions of their energy efficiency goals. Specifically, we look at the cases of Bogota, Colombia; Da Nang, Vietnam; Eskisehir, Turkey; Mexico City, Mexico; Rajkot, India; and Tshwane, South Africa, all of which are “deep dive” cities under the Sustainable Energy formore » All's Building Efficiency Accelerator. The research focuses on understanding the baseline with existing gaps in implementation and coordination. The methodology used a combination of surveys on code status and interviews with stakeholders at the local and national level, as well as review of published documents. We looked at code development, implementation, and evaluation. The cities are all working to improve implementation, however, the challenges they currently face include gaps in resources, capacity, tools, and institutions to check for compliance. Better coordination between national and local governments could help improve implementation, but that coordination is not yet well established. For example, all six of the cities reported that there was little to no involvement of local stakeholders in development of the national code; only one city reported that it had access to national funding to support code implementation. More robust coordination could better link cities with capacity building and funding for compliance, and ensure that the code reflects local priorities. By understanding gaps in implementation, it can also help in designing more targeted interventions to scale up energy savings.« less

The international implications of national and local coordination on building energy codes: Case studies in six cities

DOE PAGES

Evans, Meredydd; Yu, Sha; Staniszewski, Aaron; ...

2018-04-17

Building energy efficiency is an important strategy for reducing greenhouse gas emissions globally. In fact, 55 countries have included building energy efficiency in their Nationally Determined Contributions (NDCs) under the Paris Agreement. This research uses building energy code implementation in six cities across different continents as case studies to assess what it may take for countries to implement the ambitions of their energy efficiency goals. Specifically, we look at the cases of Bogota, Colombia; Da Nang, Vietnam; Eskisehir, Turkey; Mexico City, Mexico; Rajkot, India; and Tshwane, South Africa, all of which are “deep dive” cities under the Sustainable Energy formore » All's Building Efficiency Accelerator. The research focuses on understanding the baseline with existing gaps in implementation and coordination. The methodology used a combination of surveys on code status and interviews with stakeholders at the local and national level, as well as review of published documents. We looked at code development, implementation, and evaluation. The cities are all working to improve implementation, however, the challenges they currently face include gaps in resources, capacity, tools, and institutions to check for compliance. Better coordination between national and local governments could help improve implementation, but that coordination is not yet well established. For example, all six of the cities reported that there was little to no involvement of local stakeholders in development of the national code; only one city reported that it had access to national funding to support code implementation. More robust coordination could better link cities with capacity building and funding for compliance, and ensure that the code reflects local priorities. By understanding gaps in implementation, it can also help in designing more targeted interventions to scale up energy savings.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This document contains the State Building Energy Codes Status prepared by Pacific Northwest National Laboratory for the U.S. Department of Energy under Contract DE-AC06-76RL01830 and dated September 1996. The U.S. Department of Energy`s Office of Codes and Standards has developed this document to provide an information resource for individuals interested in energy efficiency of buildings and the relevant building energy codes in each state and U.S. territory. This is considered to be an evolving document and will be updated twice a year. In addition, special state updates will be issued as warranted.

Data Collection Handbook to Support Modeling Impacts of Radioactive Material in Soil and Building Structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Charley; Kamboj, Sunita; Wang, Cheng

2015-09-01

This handbook is an update of the 1993 version of the Data Collection Handbook and the Radionuclide Transfer Factors Report to support modeling the impact of radioactive material in soil. Many new parameters have been added to the RESRAD Family of Codes, and new measurement methodologies are available. A detailed review of available parameter databases was conducted in preparation of this new handbook. This handbook is a companion document to the user manuals when using the RESRAD (onsite) and RESRAD-OFFSITE code. It can also be used for RESRAD-BUILD code because some of the building-related parameters are included in this handbook.more » The RESRAD (onsite) has been developed for implementing U.S. Department of Energy Residual Radioactive Material Guidelines. Hydrogeological, meteorological, geochemical, geometrical (size, area, depth), crops and livestock, human intake, source characteristic, and building characteristic parameters are used in the RESRAD (onsite) code. The RESRAD-OFFSITE code is an extension of the RESRAD (onsite) code and can also model the transport of radionuclides to locations outside the footprint of the primary contamination. This handbook discusses parameter definitions, typical ranges, variations, and measurement methodologies. It also provides references for sources of additional information. Although this handbook was developed primarily to support the application of RESRAD Family of Codes, the discussions and values are valid for use of other pathway analysis models and codes.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prowell, I.; Elgamal, A.; Romanowitz, H.

Demand parameters for turbines, such as tower moment demand, are primarily driven by wind excitation and dynamics associated with operation. For that purpose, computational simulation platforms have been developed, such as FAST, maintained by the National Renewable Energy Laboratory (NREL). For seismically active regions, building codes also require the consideration of earthquake loading. Historically, it has been common to use simple building code approaches to estimate the structural demand from earthquake shaking, as an independent loading scenario. Currently, International Electrotechnical Commission (IEC) design requirements include the consideration of earthquake shaking while the turbine is operating. Numerical and analytical tools usedmore » to consider earthquake loads for buildings and other static civil structures are not well suited for modeling simultaneous wind and earthquake excitation in conjunction with operational dynamics. Through the addition of seismic loading capabilities to FAST, it is possible to simulate earthquake shaking in the time domain, which allows consideration of non-linear effects such as structural nonlinearities, aerodynamic hysteresis, control system influence, and transients. This paper presents a FAST model of a modern 900-kW wind turbine, which is calibrated based on field vibration measurements. With this calibrated model, both coupled and uncoupled simulations are conducted looking at the structural demand for the turbine tower. Response is compared under the conditions of normal operation and potential emergency shutdown due the earthquake induced vibrations. The results highlight the availability of a numerical tool for conducting such studies, and provide insights into the combined wind-earthquake loading mechanism.« less

BOCA BASIC BUILDING CODE. 4TH ED., 1965 AND 1967. BOCA BASIC BUILDING CODE ACCUMULATIVE SUPPLEMENT.

ERIC Educational Resources Information Center

Building Officials Conference of America, Inc., Chicago, IL.

NATIONALLY RECOGNIZED STANDARDS FOR THE EVALUATION OF MINIMUM SAFE PRACTICE OR FOR DETERMINING THE PERFORMANCE OF MATERIALS OR SYSTEMS OF CONSTRUCTION HAVE BEEN COMPILED AS AN AID TO DESIGNERS AND LOCAL OFFICIALS. THE CODE PRESENTS REGULATIONS IN TERMS OF MEASURED PERFORMANCE RATHER THAN IN RIGID SPECIFICATION OF MATERIALS OR METHODS. THE AREAS…

An Infrastructure for UML-Based Code Generation Tools

NASA Astrophysics Data System (ADS)

Wehrmeister, Marco A.; Freitas, Edison P.; Pereira, Carlos E.

The use of Model-Driven Engineering (MDE) techniques in the domain of distributed embedded real-time systems are gain importance in order to cope with the increasing design complexity of such systems. This paper discusses an infrastructure created to build GenERTiCA, a flexible tool that supports a MDE approach, which uses aspect-oriented concepts to handle non-functional requirements from embedded and real-time systems domain. GenERTiCA generates source code from UML models, and also performs weaving of aspects, which have been specified within the UML model. Additionally, this paper discusses the Distributed Embedded Real-Time Compact Specification (DERCS), a PIM created to support UML-based code generation tools. Some heuristics to transform UML models into DERCS, which have been implemented in GenERTiCA, are also discussed.

Green Building Tools for Tribes

EPA Pesticide Factsheets

Tribal green building tools and funding information to support tribal building code adoption, healthy building, siting, energy efficiency, renewable energy, water conservation, green building materials, recycling and adaptation and resilience.

Capturing Energy-Saving Opportunities: Improving Building Efficiency in Rajasthan through Energy Code Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Qing; Yu, Sha; Evans, Meredydd

2016-05-01

India adopted the Energy Conservation Building Code (ECBC) in 2007. Rajasthan is the first state to make ECBC mandatory at the state level. In collaboration with Malaviya National Institute of Technology (MNIT) Jaipur, Pacific Northwest National Laboratory (PNNL) has been working with Rajasthan to facilitate the implementation of ECBC. This report summarizes milestones made in Rajasthan and PNNL's contribution in institutional set-ups, capacity building, compliance enforcement and pilot building construction.

G STL: the geostatistical template library in C++

NASA Astrophysics Data System (ADS)

Remy, Nicolas; Shtuka, Arben; Levy, Bruno; Caers, Jef

2002-10-01

The development of geostatistics has been mostly accomplished by application-oriented engineers in the past 20 years. The focus on concrete applications gave birth to many algorithms and computer programs designed to address different issues, such as estimating or simulating a variable while possibly accounting for secondary information such as seismic data, or integrating geological and geometrical data. At the core of any geostatistical data integration methodology is a well-designed algorithm. Yet, despite their obvious differences, all these algorithms share many commonalities on which to build a geostatistics programming library, lest the resulting library is poorly reusable and difficult to expand. Building on this observation, we design a comprehensive, yet flexible and easily reusable library of geostatistics algorithms in C++. The recent advent of the generic programming paradigm allows us elegantly to express the commonalities of the geostatistical algorithms into computer code. Generic programming, also referred to as "programming with concepts", provides a high level of abstraction without loss of efficiency. This last point is a major gain over object-oriented programming which often trades efficiency for abstraction. It is not enough for a numerical library to be reusable, it also has to be fast. Because generic programming is "programming with concepts", the essential step in the library design is the careful identification and thorough definition of these concepts shared by most geostatistical algorithms. Building on these definitions, a generic and expandable code can be developed. To show the advantages of such a generic library, we use G STL to build two sequential simulation programs working on two different types of grids—a surface with faults and an unstructured grid—without requiring any change to the G STL code.

Pros and cons of rotating ground motion records to fault-normal/parallel directions for response history analysis of buildings

USGS Publications Warehouse

Kalkan, Erol; Kwong, Neal S.

2014-01-01

According to the regulatory building codes in the United States (e.g., 2010 California Building Code), at least two horizontal ground motion components are required for three-dimensional (3D) response history analysis (RHA) of building structures. For sites within 5 km of an active fault, these records should be rotated to fault-normal/fault-parallel (FN/FP) directions, and two RHAs should be performed separately (when FN and then FP are aligned with the transverse direction of the structural axes). It is assumed that this approach will lead to two sets of responses that envelope the range of possible responses over all nonredundant rotation angles. This assumption is examined here, for the first time, using a 3D computer model of a six-story reinforced-concrete instrumented building subjected to an ensemble of bidirectional near-fault ground motions. Peak values of engineering demand parameters (EDPs) were computed for rotation angles ranging from 0 through 180° to quantify the difference between peak values of EDPs over all rotation angles and those due to FN/FP direction rotated motions. It is demonstrated that rotating ground motions to FN/FP directions (1) does not always lead to the maximum responses over all angles, (2) does not always envelope the range of possible responses, and (3) does not provide maximum responses for all EDPs simultaneously even if it provides a maximum response for a specific EDP.

25 CFR 256.10 - When do I qualify for Category C assistance?

Code of Federal Regulations, 2011 CFR

2011-04-01

... living The dwelling cannot be brought up to applicable building code standards and to standard housing... applicable building code standards and to standard housing condition for $35,000 or less. You do not own a...

25 CFR 256.10 - When do I qualify for Category C assistance?

Code of Federal Regulations, 2014 CFR

2014-04-01

... The dwelling cannot be brought up to applicable building code standards and to standard housing... applicable building code standards and to standard housing condition for $35,000 or less. You do not own a...

25 CFR 256.10 - When do I qualify for Category C assistance?

Code of Federal Regulations, 2013 CFR

2013-04-01

... living The dwelling cannot be brought up to applicable building code standards and to standard housing... applicable building code standards and to standard housing condition for $35,000 or less. You do not own a...

25 CFR 256.10 - When do I qualify for Category C assistance?

Code of Federal Regulations, 2012 CFR

2012-04-01

... living The dwelling cannot be brought up to applicable building code standards and to standard housing... applicable building code standards and to standard housing condition for $35,000 or less. You do not own a...

25 CFR 256.10 - When do I qualify for Category C assistance?

Code of Federal Regulations, 2010 CFR

2010-04-01

... living The dwelling cannot be brought up to applicable building code standards and to standard housing... applicable building code standards and to standard housing condition for $35,000 or less. You do not own a...

Energy and Environment Guide to Action - Chapter 4.3: Building Codes for Energy Efficiency

EPA Pesticide Factsheets

Provides guidance and recommendations for establishing, implementing, and evaluating state building codes for energy efficiency, which improve energy efficiency in new construction and major renovations. State success stories are included for reference.

77 FR 29322 - Updating State Residential Building Energy Efficiency Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-17

... supporting the change to the SHGC requirements in climate zone 4. Specifically, RECA supported the... to change Climate Zone 3 from R13 to either R20 or R13+5 ci.'' (CFEC, No. 2 at p. 2) In response, DOE... difference of 50 Pascals (5 ACH50) in climate zone 1 and climate zone 2; and 3 air changes/hour (3 ACH50) in...

Comparative U.S.-Israeli Homeland Security

DTIC Science & Technology

2006-06-01

perception is the economic benefit that the United States receives from such a porous border in the form of inexpensive guest labor. Taking this argument...housing Israeli families have been back-fitted with bulletproof glass in windows that face Palestinian neighborhoods. On a much larger scale, Israel has...without requiring a metal cover; dealing with ceilings ; and creating and enforcing building codes for commercial structures so they can withstand

Progress toward a reduced phage genetic code.

PubMed

Yao, Anzhi; Reed, Sean A; Koh, Minseob; Yu, Chenguang; Luo, Xiaozhou; Mehta, Angad P; Schultz, Peter G

2018-03-26

All known living organisms use at least 20 amino acids as the basic building blocks of life. Efforts to reduce the number of building blocks in a replicating system to below the 20 canonical amino acids have not been successful to date. In this work, we use filamentous phage as a model system to investigate the feasibility of removing methionine (Met) from the proteome. We show that all 24 elongation Met sites in the M13 phage genome can be replaced by other canonical amino acids. Most of these changes involve substitution of methionine by leucine (Leu), but in some cases additional compensatory mutations are required. Combining Met substituted sites in the proteome generally led to lower viability/infectivity of the mutant phages, which remains the major challenge in eliminating all methionines from the phage proteome. To date a total of 15 (out of all 24) elongation Mets have been simultaneously deleted from the M13 proteome, providing a useful foundation for future efforts to minimize the genetic code. Copyright © 2018. Published by Elsevier Ltd.

Building a Better Trojan Horse: Emerging Army Roles in Joint Urban Operations

DTIC Science & Technology

2001-01-01

Building a Better Trojan Horse : Emerging Army Roles in Joint Urban Operations A Monograph by MAJ Christopher H. Beckert Infantry, U.S. Army School...xx-xx-2000 to xx-xx-2000 5a. CONTRACT NUMBER 5b. GRANT NUMBER 4. TITLE AND SUBTITLE Building a Better Trojan Horse : Emerging Army Roles in Joint...TELEPHONE NUMBER International Area Code Area Code Telephone Number 703 767-9007 DSN 427-9007 2 Abstract BUILDING A BETTER TROJAN HORSE : EMERGING ARMY

ControlShell: A real-time software framework

NASA Technical Reports Server (NTRS)

Schneider, Stanley A.; Chen, Vincent W.; Pardo-Castellote, Gerardo

1994-01-01

The ControlShell system is a programming environment that enables the development and implementation of complex real-time software. It includes many building tools for complex systems, such as a graphical finite state machine (FSM) tool to provide strategic control. ControlShell has a component-based design, providing interface definitions and mechanisms for building real-time code modules along with providing basic data management. Some of the system-building tools incorporated in ControlShell are a graphical data flow editor, a component data requirement editor, and a state-machine editor. It also includes a distributed data flow package, an execution configuration manager, a matrix package, and an object database and dynamic binding facility. This paper presents an overview of ControlShell's architecture and examines the functions of several of its tools.

How to Build an AppleSeed: A Parallel Macintosh Cluster for Numerically Intensive Computing

NASA Astrophysics Data System (ADS)

Decyk, V. K.; Dauger, D. E.

We have constructed a parallel cluster consisting of a mixture of Apple Macintosh G3 and G4 computers running the Mac OS, and have achieved very good performance on numerically intensive, parallel plasma particle-incell simulations. A subset of the MPI message-passing library was implemented in Fortran77 and C. This library enabled us to port code, without modification, from other parallel processors to the Macintosh cluster. Unlike Unix-based clusters, no special expertise in operating systems is required to build and run the cluster. This enables us to move parallel computing from the realm of experts to the main stream of computing.

Key ingredients needed when building large data processing systems for scientists

NASA Technical Reports Server (NTRS)

Miller, K. C.

2002-01-01

Why is building a large science software system so painful? Weren't teams of software engineers supposed to make life easier for scientists? Does it sometimes feel as if it would be easier to write the million lines of code in Fortran 77 yourself? The cause of this dissatisfaction is that many of the needs of the science customer remain hidden in discussions with software engineers until after a system has already been built. In fact, many of the hidden needs of the science customer conflict with stated needs and are therefore very difficult to meet unless they are addressed from the outset in a system's architectural requirements. What's missing is the consideration of a small set of key software properties in initial agreements about the requirements, the design and the cost of the system.

ASTM and ASME-BPE Standards--Complying with the Needs of the Pharmaceutical Industry.

PubMed

Huitt, William M

2011-01-01

Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and standards and then modifying them in order to meet the more stringent requirements of the Food and Drug Administration (FDA). In 1997 the American Society of Mechanical Engineers (ASME) published the first Bioprocessing Equipment (BPE) Standard. Through harmonization efforts this relatively new standard has brought together, scrutinized, and refined industry accepted methodologies together with FDA compliance requirements, and has established an American National Standard that provides a comprehensive set of standards that are integral to the pharmaceutical industry. This article describes various American National Standards, including those developed and published by the American Society for Testing and Materials (ASTM), and how they apply to the pharmaceutical industry. It goes on to discuss the harmonization effort that takes place between the various standards developers in an attempt to prevent conflicts and omissions between the many standards. Also included are examples of tables and figures taken from the ASME-BPE Standard. These examples provide the reader with insight to the relevant content of the ASME-BPE Standard. Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and standards and then modifying them in order to meet the more stringent requirements of the Food and Drug Administration (FDA). In 1997 the American Society of Mechanical Engineers (ASME) published the first Bioprocessing Equipment (BPE) Standard. In its initial development and ongoing maintenance it works with other American National Standards developers to harmonize the many standards associated with the design, engineering, and construction of bioprocessing facilities. This harmonization effort has established a comprehensive set of standards for the betterment of the pharmaceutical industry at large. This effort is, and will remain, very important as technology, along with new and improved product and processes, evolve into the future.

Study of potential nonconformities of a new recreation center building's envelope

NASA Astrophysics Data System (ADS)

Stanescu, M.; Kajl, S.; Lamarche, L.

2016-09-01

This article presents a building envelope's analysis in order to verify the compliance with mandatory provisions of the Model National Energy Code for Buildings in Canada (MNECB 1997). Because some of the requirements are «not met», investigations were carried out to provide justifications in order to prove that the building can be considered as an exception to the mandatory provisions of MNECB. Therefore, we evaluate the impact of three (3) potential nonconformities of the building's walls on the building energy performance. In regards to article 3.1.1.1.4 of MNECB, there is an exception if it can be proved that permanent process (like heat recovery of refrigeration compressors) can produce at all times enough heat that no other heating source is required. First of all, by using simulation, we were able to indicate that almost all building's heating will be provided by energy recovery from ice rinks refrigeration systems (99.2%). Secondly, by using an energy analysis carried out with HEAT2 software, we can show that the increase of heating energy demand caused by the 3 studied walls is very low. This represents an increase of the heating energy demand of only 0.2%, and this, regardless of the heat recovery process. Because the nonconforming wall sections are small (0.97% of the envelope area), this mainly explains the minor impact in terms of building performance. In conclusion, according to the results obtained, we were able to recommend the building for consideration as an exception to the mandatory provisions of MNECB.

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Idaho

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

The 2015 IECC provides cost-effective savings for residential buildings in Idaho. Moving to the 2015 IECC from the 2015 Idaho State Code base code is cost-effective for residential buildings in all climate zones in Idaho.

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

2016-02-15

The 2015 IECC provides cost-effective savings for residential buildings in Montana. Moving to the 2015 IECC from the 2014 Montana State Code base code is cost-effective for residential buildings in all climate zones in Montana.

75 FR 20833 - Building Energy Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-21

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy [Docket No. EERE-2010-BT-BC-0012] Building Energy Codes AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Request for Information. SUMMARY: The U.S. Department of Energy (DOE) is soliciting...

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Iowa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

2016-02-15

The 2015 IECC provides cost-effective savings for residential buildings in Iowa. Moving to the 2015 IECC from the 2014 Iowa State Code base code is cost-effective for residential buildings in all climate zones in Iowa.

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

The 2015 IECC provides cost-effective savings for residential buildings in Utah. Moving to the 2015 IECC from the 2012 Utah State Code base code is cost-effective for residential buildings in all climate zones in Utah.

Inclusion of cool roofs in nonresidential Title 24 prescriptiverequirements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levinson, Ronnen; Akbari, Hashem; Konopacki, Steve

2003-07-01

Roofs that have high solar reflectance (high ability toreflect sunlight) and high thermal emittance (high ability to radiateheat) tend to stay cool in the sun. The same is true of low-emittanceroofs with exceptionally high solar reflectance. Substituting a cool rooffor a non-cool roof tends to decrease cooling electricity use, coolingpower demand, and cooling-equipment capacity requirements, while slightlyincreasing heating energy consumption. Cool roofs can also lower citywideambient air temperature in summer, slowing ozone formation and increasinghuman comfort.DOE-2.1E building energy simulations indicate that use of acool roofing material on a prototypical California nonresidential (NR)building with a low-sloped roof yields average annual coolingmore » energysavings of approximately 3.2 kW h/m2 (300 kW h/1000 ft2), average annualnatural gas deficits of 5.6 MJ/m2 (4.9 therm/1000 ft2), average annualsource energy savings of 30 MJ/m2 (2.6 MBTU/1000 ft2), and average peakpower demand savings of 2.1 W/m2 (0.19 kW/1000 ft2). The 15-year netpresent value (NPV) of energy savings averages $4.90/m2 ($450/1000 ft2)with time-dependent valuation (TDV), and $4.00/m2 ($370/1000 ft2) withoutTDV. When cost savings from downsizing cooling equipment are included,the average total savings (15-year NPV+equipment savings) rises to$5.90/m2 ($550/1000 ft2) with TDV, and to $5.00/m2 ($470/1000 ft2)without TDV.Total savings range from 1.90 to 8.30 $/m2 (0.18 0.77 $/ft2)with TDV, and from 1.70 to 7.10 $/m2 (0.16 0.66 $/ft2) without TDV,across California's 16 climate zones. The typical cost premium for a coolroof is 0.00 2.20 $/m2 (0.00 0.20 $/ft2). Cool roofs with premiums up to$2.20/m2 ($0.20/ft2) are expected to be cost effective in climate zones 216; those with premiums not exceeding $1.90/m2 ($0.18/ft2) are expectedto be also cost effective in climate zone 1. Hence, this study recommendsthat the year-2005 California building energy efficiency code (Title 24,Part 6 of the California Code of Regulations) for NR buildings withlow-sloped roofs include a cool-roof prescriptive requirement in allCalifornia climate zones. Buildings with roofs that do not meetprescriptive requirements may comply with the code via an"overall-envelope" approach (non-metal roofs only), or via a performanceapproach (all roof types).« less

Building Codes and Regulations.

ERIC Educational Resources Information Center

Fisher, John L.

The hazard of fire is of great concern to libraries due to combustible books and new plastics used in construction and interiors. Building codes and standards can offer architects and planners guidelines to follow but these standards should be closely monitored, updated, and researched for fire prevention. (DS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbary, Lawrence D.; Perkins, Laura L.; Serino, Roland

The team led by Dow Corning collaborated to increase the thermal performance of exterior insulation and finishing systems (EIFS) to reach R-40 performance meeting the needs for high efficiency insulated walls. Additionally, the project helped remove barriers to using EIFS on retrofit commercial buildings desiring high insulated walls. The three wall systems developed within the scope of this project provide the thermal performance of R-24 to R-40 by incorporating vacuum insulation panels (VIPs) into an expanded polystyrene (EPS) encapsulated vacuum insulated sandwich element (VISE). The VISE was incorporated into an EIFS as pre-engineered insulation boards. The VISE is installed usingmore » typical EIFS details and network of trained installers. These three wall systems were tested and engineered to be fully code compliant as an EIFS and meet all of the International Building Code structural, durability and fire test requirements for a code compliant exterior wall cladding system. This system is being commercialized under the trade name Dryvit® Outsulation® HE system. Full details, specifications, and application guidelines have been developed for the system. The system has been modeled both thermally and hygrothermally to predict condensation potential. Based on weather models for Baltimore, MD; Boston, MA; Miami, FL; Minneapolis, MN; Phoenix, AZ; and Seattle, WA; condensation and water build up in the wall system is not a concern. Finally, the team conducted a field trial of the system on a building at the former Brunswick Naval Air Station which is being redeveloped by the Midcoast Regional Redevelopment Authority (Brunswick, Maine). The field trial provided a retrofit R-30 wall onto a wood frame construction, slab on grade, 1800 ft2 building, that was monitored over the course of a year. Simultaneous with the façade retrofit, the building’s windows were upgraded at no charge to this program. The retrofit building used 49% less natural gas during the winter of 2012 compared to previous winters. This project achieved its goal of developing a system that is constructible, offers protection to the VIPs, and meets all performance targets established for the project.« less

High-Penetration Photovoltaics Standards and Codes Workshop, Denver, Colorado, May 20, 2010: Workshop Proceedings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coddington, M.; Kroposki, B.; Basso, T.

Effectively interconnecting high-level penetration of photovoltaic (PV) systems requires careful technical attention to ensuring compatibility with electric power systems. Standards, codes, and implementation have been cited as major impediments to widespread use of PV within electric power systems. On May 20, 2010, in Denver, Colorado, the National Renewable Energy Laboratory, in conjunction with the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE), held a workshop to examine the key technical issues and barriers associated with high PV penetration levels with an emphasis on codes and standards. This workshop included building upon results of the Highmore » Penetration of Photovoltaic (PV) Systems into the Distribution Grid workshop held in Ontario California on February 24-25, 2009, and upon the stimulating presentations of the diverse stakeholder presentations.« less

Multiprocessing on supercomputers for computational aerodynamics

NASA Technical Reports Server (NTRS)

Yarrow, Maurice; Mehta, Unmeel B.

1991-01-01

Little use is made of multiple processors available on current supercomputers (computers with a theoretical peak performance capability equal to 100 MFLOPS or more) to improve turnaround time in computational aerodynamics. The productivity of a computer user is directly related to this turnaround time. In a time-sharing environment, such improvement in this speed is achieved when multiple processors are used efficiently to execute an algorithm. The concept of multiple instructions and multiple data (MIMD) is applied through multitasking via a strategy that requires relatively minor modifications to an existing code for a single processor. This approach maps the available memory to multiple processors, exploiting the C-Fortran-Unix interface. The existing code is mapped without the need for developing a new algorithm. The procedure for building a code utilizing this approach is automated with the Unix stream editor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lao, Lang L.; St John, Holger; Staebler, Gary M.

This report describes the work done under U.S. Department of Energy grant number DE-FG02-07ER54935 for the period ending July 31, 2010. The goal of this project was to provide predictive transport analysis to the PTRANSP code. Our contribution to this effort consisted of three parts: (a) a predictive solver suitable for use with highly non-linear transport models and installation of the turbulent confinement models GLF23 and TGLF, (b) an interface of this solver with the PTRANSP code, and (c) initial development of an EPED1 edge pedestal model interface with PTRANSP. PTRANSP has been installed locally on this cluster by importingmore » a complete PTRANSP build environment that always contains the proper version of the libraries and other object files that PTRANSP requires. The GCNMP package and its interface code have been added to the SVN repository at PPPL.« less

Building America Case Study: Sealed Crawl Spaces with Integrated Whole-House Ventilation in a Cold Climate, Ithaca, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

"9One method of code-compliance for crawlspaces is to seal and insulate the crawlspace, rather than venting to the outdoors. However, codes require mechanical ventilation; either via conditioned supply air from the HVAC system, or a continuous exhaust ventilation strategy. As the CARB's building partner, Ithaca Neighborhood Housing Services, intended to use the unvented crawlspace in a recent development, CARB was interested in investigating a hybrid ventilation method that includes the exhaust air from the crawlspace as a portion of an ASHRAE 62.2 compliant whole-house ventilation strategy. This hybrid ventilation method was evaluated through a series of long-term monitoring tests thatmore » observed temperature, humidity, and pressure conditions through the home and crawlspace. Additionally, CARB worked with NREL to perform multi-point tracer gas testing on six separate ventilation strategies - varying portions of 62.2 required flow supplied by the crawlspace fan and an upstairs bathroom fan. The intent of the tracer gas testing was to identify effective Reciprocal Age of Air (RAoA), which is equivalent to the air change rate in well-mixed zones, for each strategy while characterizing localized infiltration rates in several areas of the home.« less

Tribal Green Building Toolkit

EPA Pesticide Factsheets

This Tribal Green Building Toolkit (Toolkit) is designed to help tribal officials, community members, planners, developers, and architects develop and adopt building codes to support green building practices. Anyone can use this toolkit!

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for New Hampshire

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

2016-02-15

The 2015 IECC provides cost-effective savings for residential buildings in New Hampshire. Moving to the 2015 IECC from the 2010 New Hampshire State Code base code is cost-effective for residential buildings in all climate zones in New Hampshire.

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for North Carolina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

2016-02-15

The 2015 IECC provides cost-effective savings for residential buildings in North Carolina. Moving to the 2015 IECC from the 2012 North Carolina State Code base code is cost-effective for residential buildings in all climate zones in North Carolina.

Effect of URM infills on seismic vulnerability of Indian code designed RC frame buildings

NASA Astrophysics Data System (ADS)

Haldar, Putul; Singh, Yogendra; Paul, D. K.

2012-03-01

Unreinforced Masonry (URM) is the most common partitioning material in framed buildings in India and many other countries. Although it is well-known that under lateral loading the behavior and modes of failure of the frame buildings change significantly due to infill-frame interaction, the general design practice is to treat infills as nonstructural elements and their stiffness, strength and interaction with the frame is often ignored, primarily because of difficulties in simulation and lack of modeling guidelines in design codes. The Indian Standard, like many other national codes, does not provide explicit insight into the anticipated performance and associated vulnerability of infilled frames. This paper presents an analytical study on the seismic performance and fragility analysis of Indian code-designed RC frame buildings with and without URM infills. Infills are modeled as diagonal struts as per ASCE 41 guidelines and various modes of failure are considered. HAZUS methodology along with nonlinear static analysis is used to compare the seismic vulnerability of bare and infilled frames. The comparative study suggests that URM infills result in a significant increase in the seismic vulnerability of RC frames and their effect needs to be properly incorporated in design codes.

SpineCreator: a Graphical User Interface for the Creation of Layered Neural Models.

PubMed

Cope, A J; Richmond, P; James, S S; Gurney, K; Allerton, D J

2017-01-01

There is a growing requirement in computational neuroscience for tools that permit collaborative model building, model sharing, combining existing models into a larger system (multi-scale model integration), and are able to simulate models using a variety of simulation engines and hardware platforms. Layered XML model specification formats solve many of these problems, however they are difficult to write and visualise without tools. Here we describe a new graphical software tool, SpineCreator, which facilitates the creation and visualisation of layered models of point spiking neurons or rate coded neurons without requiring the need for programming. We demonstrate the tool through the reproduction and visualisation of published models and show simulation results using code generation interfaced directly into SpineCreator. As a unique application for the graphical creation of neural networks, SpineCreator represents an important step forward for neuronal modelling.

Seismic hazard map of North and Central America and the Caribbean

USGS Publications Warehouse

Shedlock, K.M.

1999-01-01

Minimization of the loss of life, property damage, and social and economic disruption due to earthquakes depends on reliable estimates of seismic hazard. National, state, and local government, decision makers, engineers, planners, emergency response organizations, builders, universities, and the general public require seismic hazard estimates for land use planning, improved building design and construction (including adoption of building construction codes), emergency response preparedness plans, economic forecasts, housing and employment decisions, and many more types of risk mitigation. The seismic hazard map of North and Central America and the Caribbean is the concatenation of various national and regional maps, involving a suite of approaches. The combined maps and documentation provide a useful regional seismic hazard framework and serve as a resource for any national or regional agency for further detailed studies applicable to their needs. This seismic hazard map depicts Peak Ground Acceleration (PGA) with a 10% chance of exceedance in 50 years. PGA, a short-period ground motion parameter that is proportional to force, is the most commonly mapped ground motion parameter because current building codes that include seismic provisions specify the horizontal force a building should be able to withstand during an earthquake. This seismic hazard map of North and Central America and the Caribbean depicts the likely level of short-period ground motion from earthquakes in a fifty-year window. Short-period ground motions effect short-period structures (e.g., one-to-two story buildings). The highest seismic hazard values in the region generally occur in areas that have been, or are likely to be, the sites of the largest plate boundary earthquakes.

NOBAI: a web server for character coding of geometrical and statistical features in RNA structure

PubMed Central

Knudsen, Vegeir; Caetano-Anollés, Gustavo

2008-01-01

The Numeration of Objects in Biology: Alignment Inferences (NOBAI) web server provides a web interface to the applications in the NOBAI software package. This software codes topological and thermodynamic information related to the secondary structure of RNA molecules as multi-state phylogenetic characters, builds character matrices directly in NEXUS format and provides sequence randomization options. The web server is an effective tool that facilitates the search for evolutionary history embedded in the structure of functional RNA molecules. The NOBAI web server is accessible at ‘http://www.manet.uiuc.edu/nobai/nobai.php’. This web site is free and open to all users and there is no login requirement. PMID:18448469

Kosol Kiatreungwattana | NREL

Science.gov Websites

Kosol Kiatreungwattana Kosol Kiatreungwattana Senior Engineer - Building and Renewable Energy experience in building energy systems and renewable technologies, building energy codes, LEED certified projects, sustainable high performance building design, building energy simulation analysis/optimization

Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for the District of Columbia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

2016-02-15

The 2015 IECC provides cost-effective savings for residential buildings in the District of Columbia. Moving to the 2015 IECC from the 2013 Washington DC Code base code is cost-effective for residential buildings in all climate zones in the District of Columbia.

76 FR 57982 - Building Energy Codes Cost Analysis

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-19

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy [Docket No. EERE-2011-BT-BC-0046] Building Energy Codes Cost Analysis Correction In notice document 2011-23236 beginning on page... heading ``Table 1. Cash flow components'' should read ``Table 7. Cash flow components''. [FR Doc. C1-2011...

7 CFR 1792.103 - Seismic design and construction standards for new buildings.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Structures. Copies are available from the American Society of Civil Engineers, Publications Marketing Department, 1801 Alexander Bell Drive, Reston, VA 20191-4400. E-mail: marketing@asce.org. Telephone: (800) 548-2723. Fax: (703) 295-6211. (3) 2003 International Code Council (ICC) International Building Code...

Achieving 50% Energy Savings in New Schools, Advanced Energy Design Guides: K-12 Schools (Brochure)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This fact sheet summarizes recommendations for designing elementary, middle, and high school buildings that will result in 50% less energy use than conventional new schools built to minimum code requirements. The recommendations are drawn from the Advanced Energy Design Guide for K-12 School Buildings, an ASHRAE publication that provides comprehensive recommendations for designing low-energy-use school buildings (see sidebar). Designed as a stand-alone document, this fact sheet provides key principles and a set of prescriptive design recommendations appropriate for smaller schools with insufficient budgets to fully implement best practices for integrated design and optimized performance. The recommendations have undergone a thoroughmore » analysis and review process through ASHRAE, and have been deemed the best combination of measures to achieve 50% savings in the greatest number of schools.« less

Developing Discontinuous Galerkin Methods for Solving Multiphysics Problems in General Relativity

NASA Astrophysics Data System (ADS)

Kidder, Lawrence; Field, Scott; Teukolsky, Saul; Foucart, Francois; SXS Collaboration

2016-03-01

Multi-messenger observations of the merger of black hole-neutron star and neutron star-neutron star binaries, and of supernova explosions will probe fundamental physics inaccessible to terrestrial experiments. Modeling these systems requires a relativistic treatment of hydrodynamics, including magnetic fields, as well as neutrino transport and nuclear reactions. The accuracy, efficiency, and robustness of current codes that treat all of these problems is not sufficient to keep up with the observational needs. We are building a new numerical code that uses the Discontinuous Galerkin method with a task-based parallelization strategy, a promising combination that will allow multiphysics applications to be treated both accurately and efficiently on petascale and exascale machines. The code will scale to more than 100,000 cores for efficient exploration of the parameter space of potential sources and allowed physics, and the high-fidelity predictions needed to realize the promise of multi-messenger astronomy. I will discuss the current status of the development of this new code.

Semi-automated Modular Program Constructor for physiological modeling: Building cell and organ models.

PubMed

Jardine, Bartholomew; Raymond, Gary M; Bassingthwaighte, James B

2015-01-01

The Modular Program Constructor (MPC) is an open-source Java based modeling utility, built upon JSim's Mathematical Modeling Language (MML) ( http://www.physiome.org/jsim/) that uses directives embedded in model code to construct larger, more complicated models quickly and with less error than manually combining models. A major obstacle in writing complex models for physiological processes is the large amount of time it takes to model the myriad processes taking place simultaneously in cells, tissues, and organs. MPC replaces this task with code-generating algorithms that take model code from several different existing models and produce model code for a new JSim model. This is particularly useful during multi-scale model development where many variants are to be configured and tested against data. MPC encodes and preserves information about how a model is built from its simpler model modules, allowing the researcher to quickly substitute or update modules for hypothesis testing. MPC is implemented in Java and requires JSim to use its output. MPC source code and documentation are available at http://www.physiome.org/software/MPC/.

78 FR 27906 - Lead; Renovation, Repair, and Painting Program for Public and Commercial Buildings; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... construction (NAICS code 236), e.g., commercial building construction, industrial building construction, commercial and institutional building construction, building finishing contractors, drywall and insulation... Lead; Renovation, Repair, and Painting Program for Public and Commercial Buildings; Notice of Public...

Building the Nonuniversity, Tertiary Care Center Hepatobiliary and Pancreatic Surgery Practice: Structural and Financial Considerations.

PubMed

Baker, Erin H; Siddiqui, Imran; Vrochides, Dionisios; Iannitti, David A; Martinie, John B; Rorabaugh, Lauren; Jeyarajah, D Rohan; Swan, Ryan Z

2016-12-01

Early in their careers, many new surgeons lack the background and experience to understand essential components needed to build a surgical practice. Surgical resident education is often devoid of specific instruction on the business of medicine and practice management. In particular, hepatobiliary and pancreatic (HPB) surgeons require many key components to build a successful practice secondary to significant interdisciplinary coordination and a scope of complex surgery, which spans challenging benign and malignant disease processes. In the following, we describe the required clinical and financial components for developing a successful HPB surgery practice in the nonuniversity tertiary care center. We discuss significant financial considerations for understanding community need and hospital investment, contract establishment, billing, and coding. We summarize the structural elements and key personnel necessary for establishing an effectual HPB surgical team. This article provides useful, essential information for a new HPB surgeon looking to establish a surgical practice. It also provides insight for health-care administrators as to the value an HPB surgeon can bring to a hospital or health-care system.

Selecting a Control Strategy for Plug and Process Loads

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lobato, C.; Sheppy, M.; Brackney, L.

2012-09-01

Plug and Process Loads (PPLs) are building loads that are not related to general lighting, heating, ventilation, cooling, and water heating, and typically do not provide comfort to the building occupants. PPLs in commercial buildings account for almost 5% of U.S. primary energy consumption. On an individual building level, they account for approximately 25% of the total electrical load in a minimally code-compliant commercial building, and can exceed 50% in an ultra-high efficiency building such as the National Renewable Energy Laboratory's (NREL) Research Support Facility (RSF) (Lobato et al. 2010). Minimizing these loads is a primary challenge in the designmore » and operation of an energy-efficient building. A complex array of technologies that measure and manage PPLs has emerged in the marketplace. Some fall short of manufacturer performance claims, however. NREL has been actively engaged in developing an evaluation and selection process for PPLs control, and is using this process to evaluate a range of technologies for active PPLs management that will cap RSF plug loads. Using a control strategy to match plug load use to users' required job functions is a huge untapped potential for energy savings.« less

ANSI/ASHRAE/IES Standard 90.1-2013 Preliminary Determination: Qualitative Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halverson, Mark A.; Hart, Reid; Athalye, Rahul A.

2014-03-01

Section 304(b) of the Energy Conservation and Production Act (ECPA), as amended, requires the Secretary of Energy to make a determination each time a revised version of ASHRAE Standard 90.1 is published with respect to whether the revised standard would improve energy efficiency in commercial buildings. When the U.S. Department of Energy (DOE) issues an affirmative determination on Standard 90.1, states are statutorily required to certify within two years that they have reviewed and updated the commercial provisions of their building energy code, with respect to energy efficiency, to meet or exceed the revised standard. This report provides a preliminarymore » qualitative analysis of all addenda to ANSI/ASHRAE/IES Standard 90.1-2010 (referred to as Standard 90.1-2010 or 2010 edition) that were included in ANSI/ASHRAE/IES Standard 90.1-2013 (referred to as Standard 90.1-2013 or 2013 edition).« less

Legacy Code Modernization

NASA Technical Reports Server (NTRS)

Hribar, Michelle R.; Frumkin, Michael; Jin, Haoqiang; Waheed, Abdul; Yan, Jerry; Saini, Subhash (Technical Monitor)

1998-01-01

Over the past decade, high performance computing has evolved rapidly; systems based on commodity microprocessors have been introduced in quick succession from at least seven vendors/families. Porting codes to every new architecture is a difficult problem; in particular, here at NASA, there are many large CFD applications that are very costly to port to new machines by hand. The LCM ("Legacy Code Modernization") Project is the development of an integrated parallelization environment (IPE) which performs the automated mapping of legacy CFD (Fortran) applications to state-of-the-art high performance computers. While most projects to port codes focus on the parallelization of the code, we consider porting to be an iterative process consisting of several steps: 1) code cleanup, 2) serial optimization,3) parallelization, 4) performance monitoring and visualization, 5) intelligent tools for automated tuning using performance prediction and 6) machine specific optimization. The approach for building this parallelization environment is to build the components for each of the steps simultaneously and then integrate them together. The demonstration will exhibit our latest research in building this environment: 1. Parallelizing tools and compiler evaluation. 2. Code cleanup and serial optimization using automated scripts 3. Development of a code generator for performance prediction 4. Automated partitioning 5. Automated insertion of directives. These demonstrations will exhibit the effectiveness of an automated approach for all the steps involved with porting and tuning a legacy code application for a new architecture.

CFD validation experiments for hypersonic flows

NASA Technical Reports Server (NTRS)

Marvin, Joseph G.

1992-01-01

A roadmap for CFD code validation is introduced. The elements of the roadmap are consistent with air-breathing vehicle design requirements and related to the important flow path components: forebody, inlet, combustor, and nozzle. Building block and benchmark validation experiments are identified along with their test conditions and measurements. Based on an evaluation criteria, recommendations for an initial CFD validation data base are given and gaps identified where future experiments could provide new validation data.

Understanding Energy Code Acceptance within the Alaska Building Community

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mapes, Terry S.

2012-02-14

This document presents the technical assistance provided to the Alaska Home Financing Corporation on behalf of PNNL regarding the assessment of attitudes toward energy codes within the building community in Alaska. It includes a summary of the existing situation and specific assistance requested by AHFC, the results of a questionnaire designed for builders surveyed in a suburban area of Anchorage, interviews with a lender, a building official, and a research specialist, and recommendations for future action by AHFC.

24 CFR 200.925c - Model codes.

Code of Federal Regulations, 2011 CFR

2011-04-01

... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Minimum Property Standards § 200.925c Model codes. (a... Plumbing Code, 1993 Edition, and the BOCA National Mechanical Code, 1993 Edition, excluding Chapter I, Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood...

24 CFR 200.925c - Model codes.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Minimum Property Standards § 200.925c Model codes. (a... Plumbing Code, 1993 Edition, and the BOCA National Mechanical Code, 1993 Edition, excluding Chapter I, Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood...

78 FR 47677 - DOE Activities and Methodology for Assessing Compliance With Building Energy Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... construction. Post- construction evaluations were implemented in one study in an effort to reduce these costs... these pilot studies have led to a number of recommendations and potential changes to the DOE methodology... fundamental assumptions and approaches to measuring compliance with building energy codes. This notice...

Learning by Doing: Teaching Decision Making through Building a Code of Ethics.

ERIC Educational Resources Information Center

Hawthorne, Mark D.

2001-01-01

Notes that applying abstract ethical principles to the practical business of building a code of applied ethics for a technical communication department teaches students that they share certain unarticulated or unconscious values that they can translate into ethical principles. Suggests that combining abstract theory with practical policy writing…

VS30 – A site-characterization parameter for use in building Codes, simplified earthquake resistant design, GMPEs, and ShakeMaps

USGS Publications Warehouse

Borcherdt, Roger D.

2012-01-01

VS30, defined as the average seismic shear-wave velocity from the surface to a depth of 30 meters, has found wide-spread use as a parameter to characterize site response for simplified earthquake resistant design as implemented in building codes worldwide. VS30 , as initially introduced by the author for the US 1994 NEHRP Building Code, provides unambiguous definitions of site classes and site coefficients for site-dependent response spectra based on correlations derived from extensive borehole logging and comparative ground-motion measurement programs in California. Subsequent use of VS30 for development of strong ground motion prediction equations (GMPEs) and measurement of extensive sets of VS borehole data have confirmed the previous empirical correlations and established correlations of SVS30 with VSZ at other depths. These correlations provide closed form expressions to predict S30 V at a large number of additional sites and further justify S30 V as a parameter to characterize site response for simplified building codes, GMPEs, ShakeMap, and seismic hazard mapping.

Adding EUNIS and VAULT rocket data to the VSO with Modern Perl frameworks

NASA Astrophysics Data System (ADS)

Mansky, Edmund

2017-08-01

A new Perl code is described, that uses the modern Object-oriented Moose framework, to add EUNIS and VAULT rocket data to the Virtual Solar Observatory website. The code permits the easy fixing of FITS header fields in the case where some FITS fields that are required are missing from the original data files. The code makes novel use of the Moose extensions “before” and “after” to build in dependencies so that database creation of tables occurs before the loading of data, and that the validation of file-dependent tables occurs after the loading is completed. Also described is the computation and loading of the deferred FITS field CHECKSUM into the database following the loading and validation of the file-dependent tables. The loading of the EUNIS 2006 and 2007 flight data, and the VAULT 2.0 flight data is described in detail as illustrative examples.

Modeling And Simulation Of Bar Code Scanners Using Computer Aided Design Software

NASA Astrophysics Data System (ADS)

Hellekson, Ron; Campbell, Scott

1988-06-01

Many optical systems have demanding requirements to package the system in a small 3 dimensional space. The use of computer graphic tools can be a tremendous aid to the designer in analyzing the optical problems created by smaller and less costly systems. The Spectra Physics grocery store bar code scanner employs an especially complex 3 dimensional scan pattern to read bar code labels. By using a specially written program which interfaces with a computer aided design system, we have simulated many of the functions of this complex optical system. In this paper we will illustrate how a recent version of the scanner has been designed. We will discuss the use of computer graphics in the design process including interactive tweaking of the scan pattern, analysis of collected light, analysis of the scan pattern density, and analysis of the manufacturing tolerances used to build the scanner.

Performance of Buildings in the 2009 Western Sumatra Earthquake

NASA Astrophysics Data System (ADS)

Deierlein, G.; Hart, T.; Alexander, N.; Hausler, E.; Henderson, S.; Wood, K.; Cedillos, V.; Wijanto, S.; Cabrera, C.; Rudianto, S.

2009-12-01

The M7.6 earthquake of 30 September 2009 in Western Sumatra, Indonesia caused significant damage and collapse to hundreds of buildings and the deaths of 1,117 people. In Padang City, with a population of about 900,000 people, building collapse was the primary cause of deaths and serious injuries (313 deaths and 431 serious injuries). The predominant building construction types in Padang are concrete moment frames with brick infill and masonry bearing wall systems. Concrete frames are common in multistory commercial retail buildings, offices, schools, and hotels; and masonry bearing wall systems are primarily used in low-rise (usually single story) residential and school buildings. In general, buildings that collapsed did not conform to modern seismic engineering practices that are required by the current Indonesian building code and would be expected in regions of moderate to high seismicity. While collapse of multi-story concrete buildings was more prevalent in older buildings (more than 10 years old), there were several newer buildings that collapsed. Primary deficiencies identified in collapsed or severely damaged buildings included: (a) soft or weak stories that failed in either by sidesway mechanisms or shear failures followed by loss of axial capacity of columns, (b) lack of ductile reinforcing bar detailing in concrete beams, columns, and beam-column joints, (c) poor quality concrete and mortar materials and workmanship, (d) vulnerable building configurations and designs with incomplete or deficient load paths, and (e) out-of-plane wall failures in unreinforced (or marginally reinforced) masonry. While these deficiencies may be expected in older buildings, damage and collapse to some modern (or recently rennovated buildings) indicates a lack of enforcement of building code provisions for design and construction quality assurance. Many new buildings whose structural systems were undamaged were closed due to extensive earthquake damage to brick infill walls, glass facades, ceiling systems and other architectural finishes. These demonstrated the importance of considering deformation compatibility and seismic considerations in the design and detail of architectural elements and non-structural components. Another important lesson learned from this earthquake is the critical role that buildings serve for vertical evacuation (refuge) from tsunami inundation in Padang and similar coastal cities in regions of high tsunami hazards. Severe traffic congestion immediately after the September 30 earthquake demonstrated that horizontal evacuation alone is insufficient to safely evacuate Padang City residents to high ground. Therefore, efforts must be stepped up to pre-screen, assess, and engineer buildings tha can be utilized for vertical evacuation.

A rule-based expert system applied to moisture durability of building envelopes

DOE PAGES

Boudreaux, Philip R.; Pallin, Simon B.; Accawi, Gina K.; ...

2018-01-09

The moisture durability of an envelope component such as a wall or roof is difficult to predict. Moisture durability depends on all the construction materials used, as well as the climate, orientation, air tightness, and indoor conditions. Modern building codes require more insulation and tighter construction but provide little guidance about how to ensure these energy-efficient assemblies remain moisture durable. Furthermore, as new products and materials are introduced, builders are increasingly uncertain about the long-term durability of their building envelope designs. Oak Ridge National Laboratory and the US Department of Energy’s Building America Program are applying a rule-based expert systemmore » methodology in a web tool to help designers determine whether a given wall design is likely to be moisture durable and provide expert guidance on moisture risk management specific to a wall design and climate. Finally, the expert system is populated with knowledge from both expert judgment and probabilistic hygrothermal simulation results.« less

A rule-based expert system applied to moisture durability of building envelopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boudreaux, Philip R.; Pallin, Simon B.; Accawi, Gina K.

The moisture durability of an envelope component such as a wall or roof is difficult to predict. Moisture durability depends on all the construction materials used, as well as the climate, orientation, air tightness, and indoor conditions. Modern building codes require more insulation and tighter construction but provide little guidance about how to ensure these energy-efficient assemblies remain moisture durable. Furthermore, as new products and materials are introduced, builders are increasingly uncertain about the long-term durability of their building envelope designs. Oak Ridge National Laboratory and the US Department of Energy’s Building America Program are applying a rule-based expert systemmore » methodology in a web tool to help designers determine whether a given wall design is likely to be moisture durable and provide expert guidance on moisture risk management specific to a wall design and climate. Finally, the expert system is populated with knowledge from both expert judgment and probabilistic hygrothermal simulation results.« less

Wood: a construction material for tall buildings

NASA Astrophysics Data System (ADS)

Wimmers, Guido

2017-12-01

Wood has great potential as a building material, because it is strong and lightweight, environmentally friendly and can be used in prefabricated buildings. However, only changes in building codes will make wood competitive with steel and concrete.

Green Building Standards

EPA Pesticide Factsheets

Many organizations have developed model codes or rating systems that communities may use to develop green building programs or revise building ordinances. Some of the major options are listed on this page.

A High-Granularity Approach to Modeling Energy Consumption and Savings Potential in the U.S. Residential Building Stock

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Building simulations are increasingly used in various applications related to energy efficient buildings. For individual buildings, applications include: design of new buildings, prediction of retrofit savings, ratings, performance path code compliance and qualification for incentives. Beyond individual building applications, larger scale applications (across the stock of buildings at various scales: national, regional and state) include: codes and standards development, utility program design, regional/state planning, and technology assessments. For these sorts of applications, a set of representative buildings are typically simulated to predict performance of the entire population of buildings. Focusing on the U.S. single-family residential building stock, this paper willmore » describe how multiple data sources for building characteristics are combined into a highly-granular database that preserves the important interdependencies of the characteristics. We will present the sampling technique used to generate a representative set of thousands (up to hundreds of thousands) of building models. We will also present results of detailed calibrations against building stock consumption data.« less

Documentation for the Southeast Asia seismic hazard maps

USGS Publications Warehouse

Petersen, Mark; Harmsen, Stephen; Mueller, Charles; Haller, Kathleen; Dewey, James; Luco, Nicolas; Crone, Anthony; Lidke, David; Rukstales, Kenneth

2007-01-01

The U.S. Geological Survey (USGS) Southeast Asia Seismic Hazard Project originated in response to the 26 December 2004 Sumatra earthquake (M9.2) and the resulting tsunami that caused significant casualties and economic losses in Indonesia, Thailand, Malaysia, India, Sri Lanka, and the Maldives. During the course of this project, several great earthquakes ruptured subduction zones along the southern coast of Indonesia (fig. 1) causing additional structural damage and casualties in nearby communities. Future structural damage and societal losses from large earthquakes can be mitigated by providing an advance warning of tsunamis and introducing seismic hazard provisions in building codes that allow buildings and structures to withstand strong ground shaking associated with anticipated earthquakes. The Southeast Asia Seismic Hazard Project was funded through a United States Agency for International Development (USAID)—Indian Ocean Tsunami Warning System to develop seismic hazard maps that would assist engineers in designing buildings that will resist earthquake strong ground shaking. An important objective of this project was to discuss regional hazard issues with building code officials, scientists, and engineers in Thailand, Malaysia, and Indonesia. The code communities have been receptive to these discussions and are considering updating the Thailand and Indonesia building codes to incorporate new information (for example, see notes from Professor Panitan Lukkunaprasit, Chulalongkorn University in Appendix A).

Recommendations on Implementing the Energy Conservation Building Code in Rajasthan, India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Sha; Makela, Eric J.; Evans, Meredydd

India launched the Energy Conservation Building Code (ECBC) in 2007 and Indian Bureau of Energy Efficiency (BEE) recently indicated that it would move to mandatory implementation in the 12th Five-Year Plan. The State of Rajasthan adopted ECBC with minor modifications; the new regulation is known as the Energy Conservation Building Directives – Rajasthan 2011 (ECBD-R). It became mandatory in Rajasthan on September 28, 2011. This report provides recommendations on an ECBD-R enforcement roadmap for the State of Rajasthan.

Evaluation of Force Transfer Around Openings - Experimental and Analytical Studies

Treesearch

Borjen Yeh; Tom Skaggs; Frank Lam; Minghao Li; Douglas Rammer; James Wacker

2011-01-01

Wood structural panel (WSP) sheathed shear walls and diaphragms are the primary lateral-load-resistingelements in wood-frame construction. The historical performance of light-frame structures in North America is very good due, in part, to model building codes that are designed to safeguard life safety. These model building codes have spawned continual improvement and...

Modelling Force Transfer Around Openings of Full-Scale Shear Walls

Treesearch

Tom Skaggs; Borjen Yeh; Frank Lam; Minghao Li; Doug Rammer; James Wacker

2011-01-01

Wood structural panel (WSP) sheathed shear walls and diaphragms are the primary lateralload-resisting elements in wood-frame construction. The historical performance of lightframe structures in North America has been very good due, in part, to model building codes that are designed to preserve life safety. These model building codes have spawned continual improvement...

A new discrete-element approach for the assessment of the seismic resistance of composite reinforced concrete-masonry buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calio, I.; Cannizzaro, F.; Marletta, M.

2008-07-08

In the present study a new discrete-element approach for the evaluation of the seismic resistance of composite reinforced concrete-masonry structures is presented. In the proposed model, unreinforced masonry panels are modelled by means of two-dimensional discrete-elements, conceived by the authors for modelling masonry structures, whereas the reinforced concrete elements are modelled by lumped plasticity elements interacting with the masonry panels through nonlinear interface elements. The proposed procedure was adopted for the assessment of the seismic response of a case study confined-masonry building which was conceived to be a typical representative of a wide class of residential buildings designed to themore » requirements of the 1909 issue of the Italian seismic code and widely adopted in the aftermath of the 1908 earthquake for the reconstruction of the cities of Messina and Reggio Calabria.« less

A new discrete-element approach for the assessment of the seismic resistance of composite reinforced concrete-masonry buildings

NASA Astrophysics Data System (ADS)

Caliò, I.; Cannizzaro, F.; D'Amore, E.; Marletta, M.; Pantò, B.

2008-07-01

In the present study a new discrete-element approach for the evaluation of the seismic resistance of composite reinforced concrete-masonry structures is presented. In the proposed model, unreinforced masonry panels are modelled by means of two-dimensional discrete-elements, conceived by the authors for modelling masonry structures, whereas the reinforced concrete elements are modelled by lumped plasticity elements interacting with the masonry panels through nonlinear interface elements. The proposed procedure was adopted for the assessment of the seismic response of a case study confined-masonry building which was conceived to be a typical representative of a wide class of residential buildings designed to the requirements of the 1909 issue of the Italian seismic code and widely adopted in the aftermath of the 1908 earthquake for the reconstruction of the cities of Messina and Reggio Calabria.

Synthetic building materials for transport buildings and structures

NASA Astrophysics Data System (ADS)

Gerasimova, Vera

2017-10-01

The most effective building materials account for the highest growth not only in construction of residential and public buildings, but also other capital projects including roadways, bridges, drainage, communications and other engineering projects. Advancement in the technology of more efficient and ecologically responsible insulation materials have been a priority for safety, minimal maintenance and longevity of finished construction projects. The practical use of modern building materials such as insulation, sound reduction and low energy consumption are a benefit in cost and application compared to the use of outdated heavier and labor-intensive materials. The most efficient way for maximizing insolation and sound proofing should be done during the design stages of the project according to existing codes and regulations that are required by Western Government. All methods and materials that are used need to be optimized in order to reach a high durability and low operational and maintenance cost exceeding more than 50 years of the life of the building, whether it is for public, industrial or residential use. Western construction techniques and technologies need to be applied and adapted by the Russian Federation to insure the most productive successful methods are being implemented. The issues of efficient insulation materials are outlined in this article.

Analysis of wallboard containing a phase change material

NASA Astrophysics Data System (ADS)

Tomlinson, J. J.; Heberle, D. P.

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified to accommodate walls that are covered with PCM plasterboard, and to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application.

A CFD validation roadmap for hypersonic flows

NASA Technical Reports Server (NTRS)

Marvin, Joseph G.

1992-01-01

A roadmap for computational fluid dynamics (CFD) code validation is developed. The elements of the roadmap are consistent with air-breathing vehicle design requirements and related to the important flow path components: forebody, inlet, combustor, and nozzle. Building block and benchmark validation experiments are identified along with their test conditions and measurements. Based on an evaluation criteria, recommendations for an initial CFD validation data base are given and gaps identified where future experiments would provide the needed validation data.

A CFD validation roadmap for hypersonic flows

NASA Technical Reports Server (NTRS)

Marvin, Joseph G.

1993-01-01

A roadmap for computational fluid dynamics (CFD) code validation is developed. The elements of the roadmap are consistent with air-breathing vehicle design requirements and related to the important flow path components: forebody, inlet, combustor, and nozzle. Building block and benchmark validation experiments are identified along with their test conditions and measurements. Based on an evaluation criteria, recommendations for an initial CFD validation data base are given and gaps identified where future experiments would provide the needed validation data.

Assessment and Requirements of Nuclear Reaction Databases for GCR Transport in the Atmosphere and Structures

NASA Technical Reports Server (NTRS)

Cucinotta, F. A.; Wilson, J. W.; Shinn, J. L.; Tripathi, R. K.

1998-01-01

The transport properties of galactic cosmic rays (GCR) in the atmosphere, material structures, and human body (self-shielding) am of interest in risk assessment for supersonic and subsonic aircraft and for space travel in low-Earth orbit and on interplanetary missions. Nuclear reactions, such as knockout and fragmentation, present large modifications of particle type and energies of the galactic cosmic rays in penetrating materials. We make an assessment of the current nuclear reaction models and improvements in these model for developing required transport code data bases. A new fragmentation data base (QMSFRG) based on microscopic models is compared to the NUCFRG2 model and implications for shield assessment made using the HZETRN radiation transport code. For deep penetration problems, the build-up of light particles, such as nucleons, light clusters and mesons from nuclear reactions in conjunction with the absorption of the heavy ions, leads to the dominance of the charge Z = 0, 1, and 2 hadrons in the exposures at large penetration depths. Light particles are produced through nuclear or cluster knockout and in evaporation events with characteristically distinct spectra which play unique roles in the build-up of secondary radiation's in shielding. We describe models of light particle production in nucleon and heavy ion induced reactions and make an assessment of the importance of light particle multiplicity and spectral parameters in these exposures.

Building code challenging the ethics behind adobe architecture in North Cyprus.

PubMed

Hurol, Yonca; Yüceer, Hülya; Şahali, Öznem

2015-04-01

Adobe masonry is part of the vernacular architecture of Cyprus. Thus, it is possible to use this technology in a meaningful way on the island. On the other hand, although adobe architecture is more sustainable in comparison to other building technologies, the use of it is diminishing in North Cyprus. The application of Turkish building code in the north of the island has created complications in respect of the use of adobe masonry, because this building code demands that reinforced concrete vertical tie-beams are used together with adobe masonry. The use of reinforced concrete elements together with adobe masonry causes problems in relation to the climatic response of the building as well as causing other technical and aesthetic problems. This situation makes the design of adobe masonry complicated and various types of ethical problems also emerge. The objective of this article is to analyse the ethical problems which arise as a consequence of the restrictive character of the building code, by analysing two case studies and conducting an interview with an architect who was involved with the use of adobe masonry in North Cyprus. According to the results of this article there are ethical problems at various levels in the design of both case studies. These problems are connected to the responsibilities of architects in respect of the social benefit, material production, aesthetics and affordability of the architecture as well as presenting distrustful behaviour where the obligations of architects to their clients is concerned.

10 CFR 434.505 - Reference building method.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Reference building method. 434.505 Section 434.505 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.505 Reference building method. 505...

10 CFR 434.505 - Reference building method.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Reference building method. 434.505 Section 434.505 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.505 Reference building method. 505.1...

10 CFR 434.505 - Reference building method.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Reference building method. 434.505 Section 434.505 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.505 Reference building method. 505...

10 CFR 434.505 - Reference building method.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Reference building method. 434.505 Section 434.505 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.505 Reference building method. 505...

10 CFR 434.505 - Reference building method.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Reference building method. 434.505 Section 434.505 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.505 Reference building method. 505...

Overview of the ArbiTER edge plasma eigenvalue code

NASA Astrophysics Data System (ADS)

Baver, Derek; Myra, James; Umansky, Maxim

2011-10-01

The Arbitrary Topology Equation Reader, or ArbiTER, is a flexible eigenvalue solver that is currently under development for plasma physics applications. The ArbiTER code builds on the equation parser framework of the existing 2DX code, extending it to include a topology parser. This will give the code the capability to model problems with complicated geometries (such as multiple X-points and scrape-off layers) or model equations with arbitrary numbers of dimensions (e.g. for kinetic analysis). In the equation parser framework, model equations are not included in the program's source code. Instead, an input file contains instructions for building a matrix from profile functions and elementary differential operators. The program then executes these instructions in a sequential manner. These instructions may also be translated into analytic form, thus giving the code transparency as well as flexibility. We will present an overview of how the ArbiTER code is to work, as well as preliminary results from early versions of this code. Work supported by the U.S. DOE.

Parallel Processing of Images in Mobile Devices using BOINC

NASA Astrophysics Data System (ADS)

Curiel, Mariela; Calle, David F.; Santamaría, Alfredo S.; Suarez, David F.; Flórez, Leonardo

2018-04-01

Medical image processing helps health professionals make decisions for the diagnosis and treatment of patients. Since some algorithms for processing images require substantial amounts of resources, one could take advantage of distributed or parallel computing. A mobile grid can be an adequate computing infrastructure for this problem. A mobile grid is a grid that includes mobile devices as resource providers. In a previous step of this research, we selected BOINC as the infrastructure to build our mobile grid. However, parallel processing of images in mobile devices poses at least two important challenges: the execution of standard libraries for processing images and obtaining adequate performance when compared to desktop computers grids. By the time we started our research, the use of BOINC in mobile devices also involved two issues: a) the execution of programs in mobile devices required to modify the code to insert calls to the BOINC API, and b) the division of the image among the mobile devices as well as its merging required additional code in some BOINC components. This article presents answers to these four challenges.

76 FR 42688 - Updating State Residential Building Energy Efficiency Codes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-19

... 19, 2013. ADDRESSES: Certification Statements must be addressed to the Buildings Technologies Program...-rise (greater than three stories) multifamily residential buildings and hotel, motel, and other..., townhouses, row houses, and low-rise multifamily buildings (not greater than three stories) such as...

The Vanderbilt University nanoscale science and engineering fabrication laboratory

NASA Astrophysics Data System (ADS)

Hmelo, Anthony B.; Belbusti, Edward F.; Smith, Mark L.; Brice, Sean J.; Wheaton, Robert F.

2005-08-01

Vanderbilt University has realized the design and construction of a 1635 sq. ft. Class 10,000 cleanroom facility to support the wide-ranging research mission associated with the Vanderbilt Institute for Nanoscale Science and Engineering (VINSE). By design we have brought together disparate technologies and researchers formerly dispersed across the campus to work together in a small contiguous space intended to foster interaction and synergy of nano-technologies not often found in close proximity. The space hosts a variety of tools for lithographic patterning of substrates, the deposition of thin films, the synthesis of diamond nanostructures and carbon nanotubes, and a variety of reactive ion etchers for the fabrication of nanostructures on silicon substrates. In addition, a separate 911 sq. ft. chemistry laboratory supports nanocrystal synthesis and the investigation of biomolecular films. The design criteria required an integrated space that would support the scientific agenda of the laboratory while satisfying all applicable code and safety concerns. This project required the renovation of pre-existing laboratory space with minimal disruption to ongoing activities in a mixed-use building, while meeting the requirements of the 2000 edition of the International Building Code for the variety of potentially hazardous processes that have been programmed for the space. In this paper we describe how architectural and engineering challenges were met in the areas of mitigating floor vibration issues, shielding our facility against EMI emanations, design of the contamination control facility itself, chemical storage and handling, toxic gas use and management, as well as mechanical, electrical, plumbing, lab security, fire and laboratory safety issues.

Tensile strength/yield strength (TS/YS) ratios of high-strength steel (HSS) reinforcing bars

NASA Astrophysics Data System (ADS)

Tavio, Anggraini, Retno; Raka, I. Gede Putu; Agustiar

2018-05-01

The building codes such as American Concrete Institute (ACI) 318M-14 and Standard National Indonesia (SNI) 2847:2013 require that the ratio of tensile strength (TS) and yield strength (YS) should not less than 1.25. The requirement is based on the assumption that a capability of a structural member to develop inelastic rotation capacity is a function of the length of the yield region. This paper reports an investigation on various steel grades, namely Grades 420, 550, 650, and 700 MPa, to examine the impact of different TS/YS ratios if it is less or greater than the required value. Grades 550, 650, and 700 MPa were purposely selected with the intention to examine if these higher grades are still promising to be implemented in special structural systems since they are prohibited by the building codes for longitudinal reinforcement, whereas Grade 420 MPa bars are the maximum limit of yield strength of reinforcing bars that is allowable for longitudinal reinforcement of special structural systems. Tensile tests of these steel samples were conducted under displacement controlled mode to capture the complete stress-strain curves and particularly the post-yield response of the steel bars. From the study, it can be concluded that Grade 420 performed higher TS/YS ratios and they were able to reach up to more than 1.25. However, the High Strength Still (HSS) bars (Grades 550, 600, and 700 MPa) resulted in lower TS/YS ratios (less than 1.25) compared with those of Grade 420 MPa.

28 CFR 36.607 - Guidance concerning model codes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 1 2013-07-01 2013-07-01 false Guidance concerning model codes. 36.607... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.607 Guidance concerning model codes. Upon application by an authorized representative of a...

28 CFR 36.607 - Guidance concerning model codes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 1 2014-07-01 2014-07-01 false Guidance concerning model codes. 36.607... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.607 Guidance concerning model codes. Upon application by an authorized representative of a...

28 CFR 36.607 - Guidance concerning model codes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 1 2012-07-01 2012-07-01 false Guidance concerning model codes. 36.607... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.607 Guidance concerning model codes. Upon application by an authorized representative of a...

28 CFR 36.607 - Guidance concerning model codes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 1 2011-07-01 2011-07-01 false Guidance concerning model codes. 36.607... BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes § 36.607 Guidance concerning model codes. Upon application by an authorized representative of a...

Continuous integration and quality control for scientific software

NASA Astrophysics Data System (ADS)

Neidhardt, A.; Ettl, M.; Brisken, W.; Dassing, R.

2013-08-01

Modern software has to be stable, portable, fast and reliable. This is going to be also more and more important for scientific software. But this requires a sophisticated way to inspect, check and evaluate the quality of source code with a suitable, automated infrastructure. A centralized server with a software repository and a version control system is one essential part, to manage the code basis and to control the different development versions. While each project can be compiled separately, the whole code basis can also be compiled with one central “Makefile”. This is used to create automated, nightly builds. Additionally all sources are inspected automatically with static code analysis and inspection tools, which check well-none error situations, memory and resource leaks, performance issues, or style issues. In combination with an automatic documentation generator it is possible to create the developer documentation directly from the code and the inline comments. All reports and generated information are presented as HTML page on a Web server. Because this environment increased the stability and quality of the software of the Geodetic Observatory Wettzell tremendously, it is now also available for scientific communities. One regular customer is already the developer group of the DiFX software correlator project.

[Representation of knowledge in respiratory medicine: ontology should help the coding process].

PubMed

Blanc, F-X; Baneyx, A; Charlet, J; Housset, B

2010-09-01

Access to medical knowledge is a major issue for health professionals and requires the development of terminologies. The objective of the reported work was to construct an ontology of respiratory medicine, i.e. an organized and formalized terminology composed by specific knowledge. The purpose is to help the medico-economical coding process and to represent the relevant knowledge about the patient. Our researches cover the whole life cycle of an ontology, from the development of a methodology, to building it from texts, to its use in an operational system. A computerized tool, based on the ontology, allows both a medico-economical coding and a graphical medical one. This second one will be used to index hospital reports. Our ontology counts 1913 concepts and contains all the knowledge included in the PMSI part of the SPLF thesaurus. Our tool has been evaluated and showed a recall of 80% and an accuracy of 85% regarding the medico-economical coding. The work presented in this paper justifies the approach that has been used. It must be continued on a large scale to validate our coding principles and the possibility of making enquiries on patient reports concerning clinical research. Copyright © 2010. Published by Elsevier Masson SAS.

Lessons learned from new construction utility demand side management programs and their implications for implementing building energy codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wise, B.K.; Hughes, K.R.; Danko, S.L.

1994-07-01

This report was prepared for the US Department of Energy (DOE) Office of Codes and Standards by the Pacific Northwest Laboratory (PNL) through its Building Energy Standards Program (BESP). The purpose of this task was to identify demand-side management (DSM) strategies for new construction that utilities have adopted or developed to promote energy-efficient design and construction. PNL conducted a survey of utilities and used the information gathered to extrapolate lessons learned and to identify evolving trends in utility new-construction DSM programs. The ultimate goal of the task is to identify opportunities where states might work collaboratively with utilities to promotemore » the adoption, implementation, and enforcement of energy-efficient building energy codes.« less

RESRAD model presentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, C.; Faillace, E.; Chen, S.Y.

RESRAD was one of the multimedia models selected by the US Nuclear Regulatory Commission (NRC) to include in its workshop on radiation dose modeling and demonstration of compliance with the radiological criteria for license termination. This paper is a summary of the presentation made at the workshop and focuses on the 10 questions the NRC distributed to all participants prior to the workshop. The code selection criteria, which were solicited by the NRC, for demonstrating compliance with the license termination rule are also included. Among the RESRAD family of codes, RESRAD and RESRAD-BUILD are designed for evaluating radiological contamination inmore » soils and in buildings. Many documents have been published to support the use of these codes. This paper focuses on these two codes. The pathways considered, the databases and parameters used, quality control and quality assurance, benchmarking, verification and validation of these codes, and capabilities as well as limitations of these codes are discussed in detail.« less

10 CFR 434.503 - Prototype building procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Prototype building procedure. 434.503 Section 434.503 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.503 Prototype...

10 CFR 434.503 - Prototype building procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Prototype building procedure. 434.503 Section 434.503 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.503 Prototype...

10 CFR 434.503 - Prototype building procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Prototype building procedure. 434.503 Section 434.503 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.503 Prototype...

10 CFR 434.503 - Prototype building procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Prototype building procedure. 434.503 Section 434.503 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.503 Prototype...

10 CFR 434.503 - Prototype building procedure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Prototype building procedure. 434.503 Section 434.503 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.503 Prototype...

Experimental study on lateral strength of wall-slab joint subjected to lateral cyclic load

NASA Astrophysics Data System (ADS)

Masrom, Mohd Asha'ari; Mohamad, Mohd Elfie; Hamid, Nor Hayati Abdul; Yusuff, Amer

2017-10-01

Tunnel form building has been utilised in building construction since 1960 in Malaysia. This method of construction has been applied extensively in the construction of high rise residential house (multistory building) such as condominium and apartment. Most of the tunnel form buildings have been designed according to British standard (BS) whereby there is no provision for seismic loading. The high-rise tunnel form buildings are vulnerable to seismic loading. The connections between slab and shear walls in the tunnel-form building constitute an essential link in the lateral load resisting mechanism. Malaysia is undergoing a shifting process from BS code to Eurocode (EC) for building construction since the country has realised the safety threats of earthquake. Hence, this study is intended to compare the performance of the interior wall slab joint for a tunnel form structure designed based on Euro and British codes. The experiment included a full scale test of the wall slab joint sub-assemblages under reversible lateral cyclic loading. Two sub-assemblage specimens of the wall slab joint were designed and constructed based on both codes. Each specimen was tested using lateral displacement control (drift control). The specimen designed by using Eurocode was found could survive up to 3.0% drift while BS specimen could last to 1.5% drift. The analysis results indicated that the BS specimen was governed by brittle failure modes with Ductility Class Low (DCL) while the EC specimen behaved in a ductile manner with Ductility Class Medium (DCM). The low ductility recorded in BS specimen was resulted from insufficient reinforcement provided in the BS code specimen. Consequently, the BS specimen could not absorb energy efficiently (low energy dissipation) and further sustain under inelastic deformation.

Application of LEED (trademark) and SPiRiT to a Proposed Building Design

DTIC Science & Technology

2003-03-01

TOTAL AREA S CAT ARLOC INSTALLATION NO CODE C QTY UM OCPD F CODE 1) 24004 Aberdeen Provi E1890...ARLOC INSTALLATION NO CODE C QTY UM OCPD F CODE 1) 24004 Aberdeen Provi E3832 31010 P 13,000 SF 13,000 R

Building America Best Practices Series Volume 12: Builders Challenge Guide to 40% Whole-House Energy Savings in the Cold and Very Cold Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-02-01

This best practices guide is the twelfth in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the cold and very cold climates can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. Themore » best practices described in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and thos erequirements are highlighted in the text. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

Reply to “Comment on “Should Memphis build for California's earthquakes?” From A.D. Frankel”

NASA Astrophysics Data System (ADS)

Stein, Seth; Tomasello, Joseph; Newman, Andrew

Carl Sagan observed that “extraordinary claims require extraordinary evidence.” In our view, A.D. Frankel's arguments (see accompanying Comment piece) do not reach the level required to demonstrate the counter-intuitive propositions that the earthquake hazard in the New Madrid Seismic Zone (NMSZ) is comparable to that in coastal California, and that buildings should be built to similar standards.This interchange is the latest in an ongoing debate beginning with Newman et al.'s [1999a] recommendation, based on analysis of Global Positioning System and earthquake data, that Frankel et al.'s [1996] estimate of California-level seismic hazard for the NMSZ should be reduced. Most points at issue, except for those related to the costs and benefits of the proposed new International Building Code 2000, have already been argued at length by both sides in the literature [e.g.,Schweig et al., 1999; Newman et al., 1999b, 2001; Cramer, 2001]. Hence,rather than rehash these points, we will try here to provide readers not enmeshed in this morass with an overview of the primary differences between our view and that of Frankel.

Evaluating the benefits of commercial building energy codes and improving federal incentives for code adoption.

PubMed

Gilbraith, Nathaniel; Azevedo, Inês L; Jaramillo, Paulina

2014-12-16

The federal government has the goal of decreasing commercial building energy consumption and pollutant emissions by incentivizing the adoption of commercial building energy codes. Quantitative estimates of code benefits at the state level that can inform the size and allocation of these incentives are not available. We estimate the state-level climate, environmental, and health benefits (i.e., social benefits) and reductions in energy bills (private benefits) of a more stringent code (ASHRAE 90.1-2010) relative to a baseline code (ASHRAE 90.1-2007). We find that reductions in site energy use intensity range from 93 MJ/m(2) of new construction per year (California) to 270 MJ/m(2) of new construction per year (North Dakota). Total annual benefits from more stringent codes total $506 million for all states, where $372 million are from reductions in energy bills, and $134 million are from social benefits. These total benefits range from $0.6 million in Wyoming to $49 million in Texas. Private benefits range from $0.38 per square meter in Washington State to $1.06 per square meter in New Hampshire. Social benefits range from $0.2 per square meter annually in California to $2.5 per square meter in Ohio. Reductions in human/environmental damages and future climate damages account for nearly equal shares of social benefits.

Residential building codes, affordability, and health protection: a risk-tradeoff approach.

PubMed

Hammitt, J K; Belsky, E S; Levy, J I; Graham, J D

1999-12-01

Residential building codes intended to promote health and safety may produce unintended countervailing risks by adding to the cost of construction. Higher construction costs increase the price of new homes and may increase health and safety risks through "income" and "stock" effects. The income effect arises because households that purchase a new home have less income remaining for spending on other goods that contribute to health and safety. The stock effect arises because suppression of new-home construction leads to slower replacement of less safe housing units. These countervailing risks are not presently considered in code debates. We demonstrate the feasibility of estimating the approximate magnitude of countervailing risks by combining the income effect with three relatively well understood and significant home-health risks. We estimate that a code change that increases the nationwide cost of constructing and maintaining homes by $150 (0.1% of the average cost to build a single-family home) would induce offsetting risks yielding between 2 and 60 premature fatalities or, including morbidity effects, between 20 and 800 lost quality-adjusted life years (both discounted at 3%) each year the code provision remains in effect. To provide a net health benefit, the code change would need to reduce risk by at least this amount. Future research should refine these estimates, incorporate quantitative uncertainty analysis, and apply a full risk-tradeoff approach to real-world case studies of proposed code changes.

Technology Solutions Case Study: Initial and Long-Term MOvement of Cladding Installed Over Exterior Rigid Insulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Changes in the International Energy Conservation Code (IECC) from 2009 to 2012 have resulted in the use of exterior rigid insulation becoming part of the prescriptive code requirements. With more jurisdictions adopting the 2012 IECC, builders will be required to incorporate exterior insulation in the construction of their exterior wall assemblies. For thick layers of exterior insulation (levels greater than 1.5 inches), the use of wood of furring strips attached through the insulation back to the structure has been used by many contractors and designers as a means to provide a convenient cladding attachment location. However, there has been resistancemore » to its widespread implementation due to a lack of research and understanding of the mechanisms involved and potential creep effects of the assembly under the sustained dead load of a cladding. This research conducted by Building Science Corporation evaluated the system mechanics and long-term performance of this technique.« less

Inter-Coder Agreement in One-to-Many Classification: Fuzzy Kappa.

PubMed

Kirilenko, Andrei P; Stepchenkova, Svetlana

2016-01-01

Content analysis involves classification of textual, visual, or audio data. The inter-coder agreement is estimated by making two or more coders to classify the same data units, with subsequent comparison of their results. The existing methods of agreement estimation, e.g., Cohen's kappa, require that coders place each unit of content into one and only one category (one-to-one coding) from the pre-established set of categories. However, in certain data domains (e.g., maps, photographs, databases of texts and images), this requirement seems overly restrictive. The restriction could be lifted, provided that there is a measure to calculate the inter-coder agreement in the one-to-many protocol. Building on the existing approaches to one-to-many coding in geography and biomedicine, such measure, fuzzy kappa, which is an extension of Cohen's kappa, is proposed. It is argued that the measure is especially compatible with data from certain domains, when holistic reasoning of human coders is utilized in order to describe the data and access the meaning of communication.

MSE observatory: a revised and optimized astronomical facility

NASA Astrophysics Data System (ADS)

Bauman, Steven E.; Angers, Mathieu; Benedict, Tom; Crampton, David; Flagey, Nicolas; Gedig, Mike; Green, Greg; Liu, Andy; Lo, David; Loewen, Nathan; McConnachie, Alan; Murowinski, Rick; Racine, René; Salmon, Derrick; Stiemer, Siegfried; Szeto, Kei; Wu, Di

2016-07-01

The Canada-France-Hawaii-Telescope Corporation (CFHT) plans to repurpose its observatory on the summit of Maunakea and operate a (60 segment) 11.25m aperture wide field spectroscopic survey telescope, the Maunakea Spectroscopic Explorer (MSE). The prime focus telescope will be equipped with dedicated instrumentation to take advantage of one of the best sites in the northern hemisphere and offer its users the ability to perform large surveys. Central themes of the development plan are reusing and upgrading wherever possible. MSE will reuse the CFHT site and build upon the existing observatory infrastructure, using the same building and telescope pier as CFHT, while minimizing environmental impact on the summit. MSE will require structural support upgrades to the building to meet the latest building seismic code requirements and accommodate a new larger telescope and upgraded enclosure. It will be necessary to replace the current dome since a larger slit opening is needed for a larger telescope. MSE will use a thermal management system to remove heat generated by loads from the building, flush excess heat from lower levels, and maintain the observing environment temperature. This paper describes the design approach for redeveloping the CFHT facility for MSE. Once the project is completed the new facility will be almost indistinguishable on the outside from the current CFHT observatory. Past experience and lessons learned from CFHT staff and the astronomical community will be used to create a modern, optimized, and transformative scientific data collecting machine.

European Security and Defense Policy (ESDP) After Ten Years - Current Situation and Perspectives

DTIC Science & Technology

2010-01-01

SUPPLEMENTARY NOTES 12a. DISTRIBUTION / AVAILABILITY STATEMENT 12b. DISTRIBUTION CODE 13 . ABSTRACT After ten years the ESDP has reached an important...premier_ministre/2008/11- novembre /16­ juncker/index.html - accessed 14 September 2009. 2 Javier Solana, “Preface,” in: What Ambitions for European Defense in...security of the Union, including the eventual framing of a common defense policy ….” 13 First and foremost the Treaty required member nations to build

Application of Advanced Multi-Core Processor Technologies to Oceanographic Research

DTIC Science & Technology

2014-09-30

Jordan Stanway are taking on the work of analyzing their code, and we are working on the Robot Operating System (ROS) and MOOS-DB systems to evaluate...Linux/GNU operating system that should reduce the time required to build the kernel and userspace significantly. This part of the work is vital to...the platform to be used not only as a service, but also as a private deployable package. As much as possible, this system was built using operating

P.L. 102-486, "Energy Policy Act" (1992)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2011-12-13

Amends the Energy Conservation and Production Act to set a deadline by which each State must certify to the Secretary of Energy whether its energy efficiency standards with respect to residential and commercial building codes meet or exceed those of the Council of American Building Officials (CABO) Model Energy Code, 1992, and of the American Society of Heating, Refrigerating, and Air-Conditioning Engineers, respectively.

Feedback Codes and Action Plans: Building the Capacity of First-Year Students to Apply Feedback to a Scientific Report

ERIC Educational Resources Information Center

Bird, Fiona L.; Yucel, Robyn

2015-01-01

Effective feedback can build self-assessment skills in students so that they become more competent and confident to identify and self-correct weaknesses in their work. In this study, we trialled a feedback code as part of an integrated programme of formative and summative assessment tasks, which provided feedback to first-year students on their…

Searching for Planning and Design Solutions.

ERIC Educational Resources Information Center

Roark, Steven

2001-01-01

Presents the fourth article in a series on the Longview Community College (Kansas City, Missouri) Liberal Arts building project. How architects are revising floor plans, evaluating building systems, deciding on furniture, and dealing with building codes are discussed. (GR)

MAN-004 Design Standards Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Timothy L.

2014-07-01

At Sandia National Laboratories in New Mexico (SNL/NM), the design, construction, operation, and maintenance of facilities is guided by industry standards, a graded approach, and the systematic analysis of life cycle benefits received for costs incurred. The design of the physical plant must ensure that the facilities are "fit for use," and provide conditions that effectively, efficiently, and safely support current and future mission needs. In addition, SNL/NM applies sustainable design principles, using an integrated whole-building design approach, from site planning to facility design, construction, and operation to ensure building resource efficiency and the health and productivity of occupants. Themore » safety and health of the workforce and the public, any possible effects on the environment, and compliance with building codes take precedence over project issues, such as performance, cost, and schedule. These design standards generally apply to all disciplines on all SNL/NM projects. Architectural and engineering design must be both functional and cost-effective. Facility design must be tailored to fit its intended function, while emphasizing low-maintenance, energy-efficient, and energy-conscious design. Design facilities that can be maintained easily, with readily accessible equipment areas, low maintenance, and quality systems. To promote an orderly and efficient appearance, architectural features of new facilities must complement and enhance the existing architecture at the site. As an Architectural and Engineering (A/E) professional, you must advise the Project Manager when this approach is prohibitively expensive. You are encouraged to use professional judgment and ingenuity to produce a coordinated interdisciplinary design that is cost-effective, easily contractible or buildable, high-performing, aesthetically pleasing, and compliant with applicable building codes. Close coordination and development of civil, landscape, structural, architectural, fire protection, mechanical, electrical, telecommunications, and security features is expected to ensure compatibility with planned functional equipment and to facilitate constructability. If portions of the design are subcontracted to specialists, delivery of the finished design documents must not be considered complete until the subcontracted portions are also submitted for review. You must, along with support consultants, perform functional analyses and programming in developing design solutions. These solutions must reflect coordination of the competing functional, budgetary, and physical requirements for the project. During design phases, meetings between you and the SNL/NM Project Team to discuss and resolve design issues are required. These meetings are a normal part of the design process. For specific design-review requirements, see the project-specific Design Criteria. In addition to the design requirements described in this manual, instructive information is provided to explain the sustainable building practice goals for design, construction, operation, and maintenance of SNL/NM facilities. Please notify SNL/NM personnel of design best practices not included in this manual, so they can be incorporated in future updates.« less

Verification of BWR Turbine Skyshine Dose with the MCNP5 Code Based on an Experiment Made at SHIMANE Nuclear Power Station

NASA Astrophysics Data System (ADS)

Tayama, Ryuichi; Wakasugi, Kenichi; Kawanaka, Ikunori; Kadota, Yoshinobu; Murakami, Yasuhiro

We measured the skyshine dose from turbine buildings at Shimane Nuclear Power Station Unit 1 (NS-1) and Unit 2 (NS-2), and then compared it with the dose calculated with the Monte Carlo transport code MCNP5. The skyshine dose values calculated with the MCNP5 code agreed with the experimental data within a factor of 2.8, when the roof of the turbine building was precisely modeled. We concluded that our MCNP5 calculation was valid for BWR turbine skyshine dose evaluation.

City Reach Code Technical Support Document

DOE Office of Scientific and Technical Information (OSTI.GOV)

Athalye, Rahul A.; Chen, Yan; Zhang, Jian

This report describes and analyzes a set of energy efficiency measures that will save 20% energy over ASHRAE Standard 90.1-2013. The measures will be used to formulate a Reach Code for cities aiming to go beyond national model energy codes. A coalition of U.S. cities together with other stakeholders wanted to facilitate the development of voluntary guidelines and standards that can be implemented in stages at the city level to improve building energy efficiency. The coalition's efforts are being supported by the U.S. Department of Energy via Pacific Northwest National Laboratory (PNNL) and in collaboration with the New Buildings Institute.

Soft-Input Soft-Output Modules for the Construction and Distributed Iterative Decoding of Code Networks

NASA Technical Reports Server (NTRS)

Benedetto, S.; Divsalar, D.; Montorsi, G.; Pollara, F.

1998-01-01

Soft-input soft-output building blocks (modules) are presented to construct and iteratively decode in a distributed fashion code networks, a new concept that includes, and generalizes, various forms of concatenated coding schemes.

Sustainable regulation of construction.

PubMed

2000-11-01

The seminar examined the role building codes and regulations can have in promoting a more sustainable approach to construction, particularly through their application to non-industrial building materials. A range of building materials such as straw, bamboo, rammed earth, adobe, and cob (a mixture of clay and chopped straw) were described and illustrated by slides to show their building potential. The current codes have a prime concern to protect the health and safety of people from the built environment. They have been developed almost exclusively for mainstream industrial materials and methods of construction, which makes them difficult to use with alternative, indigenous, or non-industrial building materials, even though those materials may be considered more sustainable. The argument was put forward that with only one-third of the world population living in modern industrial buildings today, it is not sustainable to re-house the remaining rapidly expanding population in high technology dwellings. Many of the low technology building materials and methods now used by the majority of people in the world need only incremental improvement to be equal or superior to many of their industrial replacements. Since these can be more sustainable methods of building, there needs to be an acceptance of the use of alternative materials, particularly in the developing parts of the world, where they are being rejected for less sustainable industrial methods. However, many codes make it difficult to use non-industrial materials; indeed, many of the industrial materials would not meet the demands that must be now met if they were now being introduced as new materials. Consequently, there is a need to develop codes to facilitate the use of a wider range of materials than in current use, and research is needed to assist this development. Sustainable regulation should take into account the full range of real impacts that materials and systems have in areas such as resource use and depletion, toxicity of the processes that produce them, and their potential for re-use and recyclability.

10 CFR 434.99 - Explanation of numbering system for codes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Explanation of numbering system for codes. 434.99 Section 434.99 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS § 434.99 Explanation of numbering system for codes. (a) For...

10 CFR 434.99 - Explanation of numbering system for codes.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Explanation of numbering system for codes. 434.99 Section 434.99 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS § 434.99 Explanation of numbering system for codes. (a) For...

Building Energy Efficiency in Rural China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Meredydd; Yu, Sha; Song, Bo

2014-04-01

Rural buildings in China now account for more than half of China’s total building energy use. Forty percent of the floorspace in China is in rural villages and towns. Most of these buildings are very energy inefficient, and may struggle to meet basic needs. They are cold in the winter, and often experience indoor air pollution from fuel use. The Chinese government plans to adopt a voluntary building energy code, or design standard, for rural homes. The goal is to build on China’s success with codes in urban areas to improve efficiency and comfort in rural homes. The Chinese governmentmore » recognizes rural buildings represent a major opportunity for improving national building energy efficiency. The challenges of rural China are also greater than those of urban areas in many ways because of the limited local capacity and low income levels. The Chinese government wants to expand on new programs to subsidize energy efficiency improvements in rural homes to build capacity for larger-scale improvement. This article summarizes the trends and status of rural building energy use in China. It then provides an overview of the new rural building design standard, and describes options and issues to move forward with implementation.« less

Mass Housing Using GFRG Panels: A Sustainable, Rapid and Affordable Solution

NASA Astrophysics Data System (ADS)

Cherian, Philip; Paul, Shinto; Krishna, S. R. Gouri; Menon, Devdas; Meher Prasad, A.

2017-06-01

This work gives an overview of research and development carried out at IIT Madras, using glass fibre reinforced gypsum (GFRG) panels, to provide an innovative solution for rapid and affordable mass housing. The GFRG panels (124 mm thick), made from recycled industrial waste gypsum (from the fertilizer industry), are prefabricated in 3 m × 12 m sizes with cellular cavities inside, which can be filled with reinforced concrete wherever required and can be used as walls as well as floor slabs. The tests carried out (over the past 12 years) establish the performance of GFRG building systems to resist gravity and lateral loads as a load-bearing system (without beams and columns) in multi-storeyed buildings up to 8-10 storeys, with adequate strength, serviceability, durability and ductility. A two-storeyed four-apartment demonstration building has also been successfully constructed in the IIT Madras campus and presently a mass housing scheme (40 apartment units) using this technology is being demonstrated at Nellore. A structural design code has also been approved by the Bureau of Indian Standards, based on the extensive studies carried out on GFRG building systems.

Estimation of building-related construction and demolition waste in Shanghai.

PubMed

Ding, Tao; Xiao, Jianzhuang

2014-11-01

One methodology is proposed to estimate the quantification and composition of building-related construction and demolition (C&D) waste in a fast developing region like Shanghai, PR China. The varieties of structure types and building waste intensities due to the requirement of progressive building design and structure codes in different decades are considered in this regional C&D waste estimation study. It is concluded that approximately 13.71 million tons of C&D waste was generated in 2012 in Shanghai, of which more than 80% of this C&D waste was concrete, bricks and blocks. Analysis from this study can be applied to facilitate C&D waste governors and researchers the duty of formulating precise policies and specifications. As a matter of fact, at least a half of the enormous amount of C&D waste could be recycled if implementing proper recycling technologies and measures. The appropriate managements would be economically and environmentally beneficial to Shanghai where the per capita per year output of C&D waste has been as high as 842 kg in 2010. Copyright © 2014 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

By working with builder partners on test homes, researchers from the U.S. Department of Energy’s Building America program can vet whole-house building strategies and avoid potential unintended consequences of implementing untested solution packages on a production scale. To support this research, Building America team Consortium for Advanced Residential Buildings (CARB) partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, Connecticut. The philosophy and science behind the 2,700 ft2 “Performance House” was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adaptable to the needs of homeowners. The technologies and strategies usedmore » in the “Performance House” were best practices rather than cutting edge, with a focus on simplicity in construction, maintenance, and operation. Achieving 30% source energy savings compared with a home built to the 2009 International Energy Conservation Code in the cold climate zone requires that nearly all components and systems be optimized. Careful planning and design are critical. The end result was a DOE Challenge Home that achieved a Home Energy Rating System (HERS) Index Score of 20 (43 without photovoltaics [PV]).« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

By working with builder partners on test homes, researchers from the U.S. Department of Energy's Building America program can vet whole-house building strategies and avoid potential unintended consequences of implementing untested solution packages on a production scale. To support this research, Building America team Consortium for Advanced Residential Buildings (CARB) partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, Connecticut. The philosophy and science behind the 2,700 ft2 "Performance House" was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adaptable to the needs of homeowners. The technologies and strategies usedmore » in the "Performance House" were best practices rather than cutting edge, with a focus on simplicity in construction, maintenance, and operation. Achieving 30% source energy savings compared with a home built to the 2009 International Energy Conservation Code in the cold climate zone requires that nearly all components and systems be optimized. Careful planning and design are critical. The end result was a DOE Challenge Home that achieved a Home Energy Rating System (HERS) Index Score of 20 (43 without photovoltaics [PV]).« less

Can you build an iPhone app without writing a single line of code?

NASA Astrophysics Data System (ADS)

Ramachandran, R.; Maskey, M.

2011-12-01

At the last ESIP summer meeting, a study was conducted to explore different commercial tools now available that allow one to create a mobile app without writing a single line of code. The proposed research comprised of two components. First, systematically evaluate different tools to create mobile apps along the dimensions of features and price. Second, create an iPhone app prototype for the ESIP community using some of these tools. The initial assessment classified the currently available tools to create mobile app tools into two categories. The tools that fall under the first category require no programming, but the content for the mobile apps are fed to it either via a web site RSS feed or entered manually. Consequently, these tools only support limited user interactivity. These tools follow the business model of website hosting services. This business model offers a set of templates to the end users with limited customization features to create their content in order to publish to websites. The second category of tools requires programming, but the code can be written in popular languages such as Javascript (compatible with most mobile platforms) rather than mobile app specific languages. For the second component of the study, two ESIP iPhone app prototypes were created. The first prototype required no programming and used the AppMakr tool. Objective C was used to create the second iPhone prototype from scratch and the source code for this prototype is available on the ESIP website. The study concluded that existing tools do make it easy to create a simple mobile app especially if one already has a well designed website. The associated costs are adequate but not cheap. However, if the mobile app has requirements that require interactivity and specialized customization then one needs to work with a mobile app developer.

Effective Cyber Situation Awareness (CSA) Assessment and Training

DTIC Science & Technology

2013-11-01

activity/scenario. y. Save Wireshark Captures. z. Save SNORT logs. aa. Save MySQL databases. 4. After the completion of the scenario, the reversion...line or from custom Java code. • Cisco ASA Parser: Builds normalized vendor-neutral firewall rule specifications from Cisco ASA and PIX firewall...The Service tool lets analysts build Cauldron models from either the command line or from custom Java code. Functionally, it corresponds to the

Quantifying the benefits of a building retrofit using an integrated system approach: A case study

DOE PAGES

Regnier, Cynthia; Sun, Kaiyu; Hong, Tianzhen; ...

2017-11-11

Building retrofits provide a large opportunity to significantly reduce energy consumption in the buildings sector. Traditional building retrofits focus on equipment upgrades, often at the end of equipment life or failure, and result in replacement with marginally improved similar technology and limited energy savings. The Integrated System (IS) retrofit approach enables much greater energy savings by leveraging interactive effects between end use systems, enabling downsized or lower energy technologies. This work presents a case study in Hawaii quantifying the benefits of an IS retrofit approach compared to two traditional retrofit approaches: a Standard Practice of upgrading equipment to meet minimummore » code requirements, and an Improved Practice of upgrading equipment to a higher efficiency. The IS approach showed an energy savings of 84% over existing building energy use, much higher than the traditional approaches of 13% and 33%. The IS retrofit also demonstrated the greatest energy cost savings potential. While the degree of savings realized from the IS approach will vary by building and climate, these findings indicate that savings on the order of 50% and greater are not possible without an IS approach. It is therefore recommended that the IS approach be universally adopted to achieve deep energy savings.« less

Quantifying the benefits of a building retrofit using an integrated system approach: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Regnier, Cynthia; Sun, Kaiyu; Hong, Tianzhen

Building retrofits provide a large opportunity to significantly reduce energy consumption in the buildings sector. Traditional building retrofits focus on equipment upgrades, often at the end of equipment life or failure, and result in replacement with marginally improved similar technology and limited energy savings. The Integrated System (IS) retrofit approach enables much greater energy savings by leveraging interactive effects between end use systems, enabling downsized or lower energy technologies. This work presents a case study in Hawaii quantifying the benefits of an IS retrofit approach compared to two traditional retrofit approaches: a Standard Practice of upgrading equipment to meet minimummore » code requirements, and an Improved Practice of upgrading equipment to a higher efficiency. The IS approach showed an energy savings of 84% over existing building energy use, much higher than the traditional approaches of 13% and 33%. The IS retrofit also demonstrated the greatest energy cost savings potential. While the degree of savings realized from the IS approach will vary by building and climate, these findings indicate that savings on the order of 50% and greater are not possible without an IS approach. It is therefore recommended that the IS approach be universally adopted to achieve deep energy savings.« less

Analysis of wallboard containing a phase change material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomlinson, J.J.; Heberle, D.P.

1990-01-01

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified tomore » accommodate walls that are covered with PCM plasterboard, nd to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application. 5 refs., 4 figs., 4 tabs.« less

Passive cooling and heating program at Oak Ridge National Laboratory for FY-1981

NASA Astrophysics Data System (ADS)

Shapira, H. B.; Kaplan, S. I.; Chester, C. V.

Construction was completed of an earth-sheltered, passively solar heated office-dormitory, the Joint Institute for Heavy Ion Research, designed at ORNL. Instrumentation of the building was designed, procured, and installed. Building performance will be monitored and compared with predictions of the DOE-2 code. A study of the incorporation of vegetation on architecture was conducted by the Harvard School of Design. A final report was issued which is a prototype handbook for the use of vegetation to reduce cooling loads in structures. An experiment to reduce the cooling requirement of mobile homes by shading with fast-growing vines was begun: a maintenance-oriented trellis was constructed and vines were planted. An RFP for the production of a prototype set of reflective insulating blinds was issued.

Shock-driven fluid-structure interaction for civil design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, Stephen L; Deiterding, Ralf

The multiphysics fluid-structure interaction simulation of shock-loaded structures requires the dynamic coupling of a shock-capturing flow solver to a solid mechanics solver for large deformations. The Virtual Test Facility combines a Cartesian embedded boundary approach with dynamic mesh adaptation in a generic software framework of flow solvers using hydrodynamic finite volume upwind schemes that are coupled to various explicit finite element solid dynamics solvers (Deiterding et al., 2006). This paper gives a brief overview of the computational approach and presents first simulations that utilize the general purpose solid dynamics code DYNA3D for complex 3D structures of interest in civil engineering.more » Results from simulations of a reinforced column, highway bridge, multistory building, and nuclear reactor building are presented.« less

LOFT. "Exploded view" of loft containment building (TAN650), including control ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LOFT. "Exploded view" of loft containment building (TAN-650), including control building (TAN-630). EG&G. February 1979. INEEL index code no. 036-010-65-220-209565 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

High-Rising Rec Centers.

ERIC Educational Resources Information Center

Whitney, Tim

2000-01-01

Examines how tight urban sites can yield sports spaces that favorably compare to their more rural campus counterparts. Potential areas of concern when recreation centers are reconfigured into high-rise structures are highlighted, including building codes, building access, noise control, building costs, and lighting. (GR)

NSDann2BS, a neutron spectrum unfolding code based on neural networks technology and two bonner spheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz-Rodriguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.

In this work a neutron spectrum unfolding code, based on artificial intelligence technology is presented. The code called ''Neutron Spectrometry and Dosimetry with Artificial Neural Networks and two Bonner spheres'', (NSDann2BS), was designed in a graphical user interface under the LabVIEW programming environment. The main features of this code are to use an embedded artificial neural network architecture optimized with the ''Robust design of artificial neural networks methodology'' and to use two Bonner spheres as the only piece of information. In order to build the code here presented, once the net topology was optimized and properly trained, knowledge stored atmore » synaptic weights was extracted and using a graphical framework build on the LabVIEW programming environment, the NSDann2BS code was designed. This code is friendly, intuitive and easy to use for the end user. The code is freely available upon request to authors. To demonstrate the use of the neural net embedded in the NSDann2BS code, the rate counts of {sup 252}Cf, {sup 241}AmBe and {sup 239}PuBe neutron sources measured with a Bonner spheres system.« less

NSDann2BS, a neutron spectrum unfolding code based on neural networks technology and two bonner spheres

NASA Astrophysics Data System (ADS)

Ortiz-Rodríguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.; Solís Sánches, L. O.; Miranda, R. Castañeda; Cervantes Viramontes, J. M.; Vega-Carrillo, H. R.

2013-07-01

In this work a neutron spectrum unfolding code, based on artificial intelligence technology is presented. The code called "Neutron Spectrometry and Dosimetry with Artificial Neural Networks and two Bonner spheres", (NSDann2BS), was designed in a graphical user interface under the LabVIEW programming environment. The main features of this code are to use an embedded artificial neural network architecture optimized with the "Robust design of artificial neural networks methodology" and to use two Bonner spheres as the only piece of information. In order to build the code here presented, once the net topology was optimized and properly trained, knowledge stored at synaptic weights was extracted and using a graphical framework build on the LabVIEW programming environment, the NSDann2BS code was designed. This code is friendly, intuitive and easy to use for the end user. The code is freely available upon request to authors. To demonstrate the use of the neural net embedded in the NSDann2BS code, the rate counts of 252Cf, 241AmBe and 239PuBe neutron sources measured with a Bonner spheres system.

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2008

Treesearch

David McKeever

2010-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only. Buildings with five or more stories are normally severely restricted by building code from being wood...

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2003

Treesearch

David B. McKeever; Craig Adair; Jennifer O' Connor

2005-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only, because buildings with five or more stories are normally severely restricted by building code from...

Building Needs for the Handicapped.

ERIC Educational Resources Information Center

Windham Southeast Supervisory Union, Brattleboro, VT.

Listed in the document are specific building needs for the handicapped. It is explained that the detailed survey forms can be used to determine building accessibility for a wide range of handicapping conditions. Survey information includes the specific building need (e.g. 12 foot wide parking space) and the letter code for affected function. Space…

49 CFR 41.110 - New DOT owned buildings and additions to buildings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... architect's authenticated verifications of seismic design codes, standards, and practices used in the design... for the design and construction of new DOT Federally owned buildings will ensure that each building is designed and constructed in accord with the seismic design and construction standards set out in § 41.120...

Examining hospital pharmacists' goals for medication counseling within the communication accommodation theoretical framework.

PubMed

Chevalier, Bernadette A M; Watson, Bernadette M; Barras, Michael A; Cottrell, William Neil

2016-01-01

Medication counseling opportunities are key times for pharmacists to speak to patients about their medications and any changes made during their hospital stay. Communication Accommodation Theory (CAT) posits that an individual's goals drive their communication behavior. The way in which pharmacists communicate with patients may be determined by the goals they set for these medication counseling sessions. To examine hospital pharmacists' goals in patient medication counseling within the CAT framework. Hospital pharmacist focus groups were held in two teaching hospitals. Interested pharmacists attended a focus group designed to elicit their goals in patient medication counseling. Focus groups were audio recorded and transcribed verbatim. NVivo(®) software was used to assist in coding and organization. The codes were reviewed for reliability by pharmacists independent of the focus groups. An inductive thematic analysis was applied to the data. Six 1 h focus groups were conducted with a total of 24 pharmacists participating. Saturation of information was achieved after four focus groups. Greater than 80% consensus was achieved for reliability of the identified codes. Patient-centered themes constructed from these codes were to build rapport, to empower patients and to improve patients' experience, health and safety. Exemplars provided by pharmacists for the goals of building rapport and empowering patients were aligned with five CAT communication behaviors (approximation, interpretability, discourse management, emotional expression and interpersonal control). Patient-centered goals described by hospital pharmacists for medication counseling aligned well with CAT behaviors necessary for effective communication. Further research using the CAT framework to examine the effectiveness of hospital pharmacist-patient exchanges that include both participants' perspectives is required to better understand how well pharmacists communicate with patients. Copyright © 2015 Elsevier Inc. All rights reserved.

Compiling standardized information from clinical practice: using content analysis and ICF Linking Rules in a goal-oriented youth rehabilitation program.

PubMed

Lustenberger, Nadia A; Prodinger, Birgit; Dorjbal, Delgerjargal; Rubinelli, Sara; Schmitt, Klaus; Scheel-Sailer, Anke

2017-09-23

To illustrate how routinely written narrative admission and discharge reports of a rehabilitation program for eight youths with chronic neurological health conditions can be transformed to the International Classification of Functioning, Disability and Health. First, a qualitative content analysis was conducted by building meaningful units with text segments assigned of the reports to the five elements of the Rehab-Cycle ® : goal; assessment; assignment; intervention; evaluation. Second, the meaningful units were then linked to the ICF using the refined ICF Linking Rules. With the first step of transformation, the emphasis of the narrative reports changed to a process oriented interdisciplinary layout, revealing three thematic blocks of goals: mobility, self-care, mental, and social functions. The linked 95 unique ICF codes could be grouped in clinically meaningful goal-centered ICF codes. Between the two independent linkers, the agreement rate was improved after complementing the rules with additional agreements. The ICF Linking Rules can be used to compile standardized health information from narrative reports if prior structured. The process requires time and expertise. To implement the ICF into common practice, the findings provide the starting point for reporting rehabilitation that builds upon existing practice and adheres to international standards. Implications for Rehabilitation This study provides evidence that routinely collected health information from rehabilitation practice can be transformed to the International Classification of Functioning, Disability and Health by using the "ICF Linking Rules", however, this requires time and expertise. The Rehab-Cycle ® , including assessments, assignments, goal setting, interventions and goal evaluation, serves as feasible framework for structuring this rehabilitation program and ensures that the complexity of local practice is appropriately reflected. The refined "ICF Linking Rules" lead to a standardized transformation process of narrative text and thus a higher quality with increased transparency. As a next step, the resulting format of goal codes supplemented by goal-clarifying codes could be validated to strengthen the implementation of the International Classification of Functioning, Disability and Health into rehabilitation routine by respecting the variety of clinical practice.

28 CFR 36.604 - Procedure following preliminary determination of equivalency.

Code of Federal Regulations, 2014 CFR

2014-07-01

... State Laws or Local Building Codes § 36.604 Procedure following preliminary determination of equivalency... of the preliminary determination of equivalency with respect to the particular code, and invite... enforcement of the code, at which interested individuals, including individuals with disabilities, are...

28 CFR 36.604 - Procedure following preliminary determination of equivalency.

Code of Federal Regulations, 2011 CFR

2011-07-01

... State Laws or Local Building Codes § 36.604 Procedure following preliminary determination of equivalency... of the preliminary determination of equivalency with respect to the particular code, and invite... enforcement of the code, at which interested individuals, including individuals with disabilities, are...

28 CFR 36.604 - Procedure following preliminary determination of equivalency.

Code of Federal Regulations, 2012 CFR

2012-07-01

... State Laws or Local Building Codes § 36.604 Procedure following preliminary determination of equivalency... of the preliminary determination of equivalency with respect to the particular code, and invite... enforcement of the code, at which interested individuals, including individuals with disabilities, are...

28 CFR 36.604 - Procedure following preliminary determination of equivalency.

Code of Federal Regulations, 2013 CFR

2013-07-01

... State Laws or Local Building Codes § 36.604 Procedure following preliminary determination of equivalency... of the preliminary determination of equivalency with respect to the particular code, and invite... enforcement of the code, at which interested individuals, including individuals with disabilities, are...

28 CFR 36.603 - Preliminary determination.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... filed by a submitting official for certification of a code, and after consultation with the...

28 CFR 36.603 - Preliminary determination.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... filed by a submitting official for certification of a code, and after consultation with the...

28 CFR 36.603 - Preliminary determination.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... filed by a submitting official for certification of a code, and after consultation with the...

28 CFR 36.603 - Preliminary determination.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building Codes... filed by a submitting official for certification of a code, and after consultation with the...

Cohort-specific imputation of gene expression improves prediction of warfarin dose for African Americans.

PubMed

Gottlieb, Assaf; Daneshjou, Roxana; DeGorter, Marianne; Bourgeois, Stephane; Svensson, Peter J; Wadelius, Mia; Deloukas, Panos; Montgomery, Stephen B; Altman, Russ B

2017-11-24

Genome-wide association studies are useful for discovering genotype-phenotype associations but are limited because they require large cohorts to identify a signal, which can be population-specific. Mapping genetic variation to genes improves power and allows the effects of both protein-coding variation as well as variation in expression to be combined into "gene level" effects. Previous work has shown that warfarin dose can be predicted using information from genetic variation that affects protein-coding regions. Here, we introduce a method that improves dose prediction by integrating tissue-specific gene expression. In particular, we use drug pathways and expression quantitative trait loci knowledge to impute gene expression-on the assumption that differential expression of key pathway genes may impact dose requirement. We focus on 116 genes from the pharmacokinetic and pharmacodynamic pathways of warfarin within training and validation sets comprising both European and African-descent individuals. We build gene-tissue signatures associated with warfarin dose in a cohort-specific manner and identify a signature of 11 gene-tissue pairs that significantly augments the International Warfarin Pharmacogenetics Consortium dosage-prediction algorithm in both populations. Our results demonstrate that imputed expression can improve dose prediction and bridge population-specific compositions. MATLAB code is available at https://github.com/assafgo/warfarin-cohort.

The development of fuel performance models at the European institute for transuranium elements

NASA Astrophysics Data System (ADS)

Lassmann, K.; Ronchi, C.; Small, G. J.

1989-07-01

The design and operational performance of fuel rods for nuclear power stations has been the subject of detailed experimental research for over thirty years. In the last two decades the continuous demands for greater economy in conjunction with more stringent safety criteria have led to an increasing reliance on computer simulations. Conditions within a fuel rod must be calculated both for normal operation and for proposed reactor faults. It has thus been necessary to build up a reliable, theoretical understanding of the intricate physical, mechanical and chemical processes occurring under a wide range of conditions to obtain a quantitative insight into the behaviour of the fuel. A prime requirement, which has also proved to be the most taxing, is to predict the conditions under which failure of the cladding might occur, particularly in fuel nearing the end of its useful life. In this paper the general requirements of a fuel performance code are discussed briefly and an account is given of the basic concepts of code construction. An overview is then given of recent progress at the European Institute for Transuranium Elements in the development of a fuel rod performance code for general application and of more detailed mechanistic models for fission product behaviour.

44 CFR 79.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... authorized native organization, that has zoning and building code jurisdiction over a particular area having... of each claim (including building and contents payments) exceeding $5,000, and with the cumulative... (building payments only) have been made under such coverage, with cumulative amount of such claims exceeding...

44 CFR 79.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... authorized native organization, that has zoning and building code jurisdiction over a particular area having... of each claim (including building and contents payments) exceeding $5,000, and with the cumulative... (building payments only) have been made under such coverage, with cumulative amount of such claims exceeding...

49 CFR 41.119 - DOT regulated buildings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... compliance may include the engineer's and architect's authenticated verification of seismic design codes... and additions to existing buildings will ensure that each DOT regulated building is designed and constructed in accord with seismic design and construction standards as provided by this part. (b) This...

PD5: a general purpose library for primer design software.

PubMed

Riley, Michael C; Aubrey, Wayne; Young, Michael; Clare, Amanda

2013-01-01

Complex PCR applications for large genome-scale projects require fast, reliable and often highly sophisticated primer design software applications. Presently, such applications use pipelining methods to utilise many third party applications and this involves file parsing, interfacing and data conversion, which is slow and prone to error. A fully integrated suite of software tools for primer design would considerably improve the development time, the processing speed, and the reliability of bespoke primer design software applications. The PD5 software library is an open-source collection of classes and utilities, providing a complete collection of software building blocks for primer design and analysis. It is written in object-oriented C(++) with an emphasis on classes suitable for efficient and rapid development of bespoke primer design programs. The modular design of the software library simplifies the development of specific applications and also integration with existing third party software where necessary. We demonstrate several applications created using this software library that have already proved to be effective, but we view the project as a dynamic environment for building primer design software and it is open for future development by the bioinformatics community. Therefore, the PD5 software library is published under the terms of the GNU General Public License, which guarantee access to source-code and allow redistribution and modification. The PD5 software library is downloadable from Google Code and the accompanying Wiki includes instructions and examples: http://code.google.com/p/primer-design.

Building A Community Focused Data and Modeling Collaborative platform with Hardware Virtualization Technology

NASA Astrophysics Data System (ADS)

Michaelis, A.; Wang, W.; Melton, F. S.; Votava, P.; Milesi, C.; Hashimoto, H.; Nemani, R. R.; Hiatt, S. H.

2009-12-01

As the length and diversity of the global earth observation data records grow, modeling and analyses of biospheric conditions increasingly requires multiple terabytes of data from a diversity of models and sensors. With network bandwidth beginning to flatten, transmission of these data from centralized data archives presents an increasing challenge, and costs associated with local storage and management of data and compute resources are often significant for individual research and application development efforts. Sharing community valued intermediary data sets, results and codes from individual efforts with others that are not in direct funded collaboration can also be a challenge with respect to time, cost and expertise. We purpose a modeling, data and knowledge center that houses NASA satellite data, climate data and ancillary data where a focused community may come together to share modeling and analysis codes, scientific results, knowledge and expertise on a centralized platform, named Ecosystem Modeling Center (EMC). With the recent development of new technologies for secure hardware virtualization, an opportunity exists to create specific modeling, analysis and compute environments that are customizable, “archiveable” and transferable. Allowing users to instantiate such environments on large compute infrastructures that are directly connected to large data archives may significantly reduce costs and time associated with scientific efforts by alleviating users from redundantly retrieving and integrating data sets and building modeling analysis codes. The EMC platform also provides the possibility for users receiving indirect assistance from expertise through prefabricated compute environments, potentially reducing study “ramp up” times.

Enhanced modeling features within TREETOPS

NASA Technical Reports Server (NTRS)

Vandervoort, R. J.; Kumar, Manoj N.

1989-01-01

The original motivation for TREETOPS was to build a generic multi-body simulation and remove the burden of writing multi-body equations from the engineers. The motivation of the enhancement was twofold: (1) to extend the menu of built-in features (sensors, actuators, constraints, etc.) that did not require user code; and (2) to extend the control system design capabilities by linking with other government funded software (NASTRAN and MATLAB). These enhancements also serve to bridge the gap between structures and control groups. It is common on large space programs for the structures groups to build hi-fidelity models of the structure using NASTRAN and for the controls group to build lower order models because they lack the tools to incorporate the former into their analysis. Now the controls engineers can accept the hi-fidelity NASTRAN models into TREETOPS, add sensors and actuators, perform model reduction and couple the result directly into MATLAB to perform their design. The controller can then be imported directly into TREETOPS for non-linear, time-history simulation.

Experimental Analysis of Steel Beams Subjected to Fire Enhanced by Brillouin Scattering-Based Fiber Optic Sensor Data.

PubMed

Bao, Yi; Chen, Yizheng; Hoehler, Matthew S; Smith, Christopher M; Bundy, Matthew; Chen, Genda

2017-01-01

This paper presents high temperature measurements using a Brillouin scattering-based fiber optic sensor and the application of the measured temperatures and building code recommended material parameters into enhanced thermomechanical analysis of simply supported steel beams subjected to combined thermal and mechanical loading. The distributed temperature sensor captures detailed, nonuniform temperature distributions that are compared locally with thermocouple measurements with less than 4.7% average difference at 95% confidence level. The simulated strains and deflections are validated using measurements from a second distributed fiber optic (strain) sensor and two linear potentiometers, respectively. The results demonstrate that the temperature-dependent material properties specified in the four investigated building codes lead to strain predictions with less than 13% average error at 95% confidence level and that the Europe building code provided the best predictions. However, the implicit consideration of creep in Europe is insufficient when the beam temperature exceeds 800°C.

Towards a semantic medical Web: HealthCyberMap's tool for building an RDF metadata base of health information resources based on the Qualified Dublin Core Metadata Set.

PubMed

Boulos, Maged N; Roudsari, Abdul V; Carson, Ewart R

2002-07-01

HealthCyberMap (http://healthcybermap.semanticweb.org/) aims at mapping Internet health information resources in novel ways for enhanced retrieval and navigation. This is achieved by collecting appropriate resource metadata in an unambiguous form that preserves semantics. We modelled a qualified Dublin Core (DC) metadata set ontology with extra elements for resource quality and geographical provenance in Prot g -2000. A metadata collection form helps acquiring resource instance data within Prot g . The DC subject field is populated with UMLS terms directly imported from UMLS Knowledge Source Server using UMLS tab, a Prot g -2000 plug-in. The project is saved in RDFS/RDF. The ontology and associated form serve as a free tool for building and maintaining an RDF medical resource metadata base. The UMLS tab enables browsing and searching for concepts that best describe a resource, and importing them to DC subject fields. The resultant metadata base can be used with a search and inference engine, and have textual and/or visual navigation interface(s) applied to it, to ultimately build a medical Semantic Web portal. Different ways of exploiting Prot g -2000 RDF output are discussed. By making the context and semantics of resources, not merely their raw text and formatting, amenable to computer 'understanding,' we can build a Semantic Web that is more useful to humans than the current Web. This requires proper use of metadata and ontologies. Clinical codes can reliably describe the subjects of medical resources, establish the semantic relationships (as defined by underlying coding scheme) between related resources, and automate their topical categorisation.

Large liquid rocket engine transient performance simulation system

NASA Technical Reports Server (NTRS)

Mason, J. R.; Southwick, R. D.

1989-01-01

Phase 1 of the Rocket Engine Transient Simulation (ROCETS) program consists of seven technical tasks: architecture; system requirements; component and submodel requirements; submodel implementation; component implementation; submodel testing and verification; and subsystem testing and verification. These tasks were completed. Phase 2 of ROCETS consists of two technical tasks: Technology Test Bed Engine (TTBE) model data generation; and system testing verification. During this period specific coding of the system processors was begun and the engineering representations of Phase 1 were expanded to produce a simple model of the TTBE. As the code was completed, some minor modifications to the system architecture centering on the global variable common, GLOBVAR, were necessary to increase processor efficiency. The engineering modules completed during Phase 2 are listed: INJTOO - main injector; MCHBOO - main chamber; NOZLOO - nozzle thrust calculations; PBRNOO - preburner; PIPE02 - compressible flow without inertia; PUMPOO - polytropic pump; ROTROO - rotor torque balance/speed derivative; and TURBOO - turbine. Detailed documentation of these modules is in the Appendix. In addition to the engineering modules, several submodules were also completed. These submodules include combustion properties, component performance characteristics (maps), and specific utilities. Specific coding was begun on the system configuration processor. All functions necessary for multiple module operation were completed but the SOLVER implementation is still under development. This system, the Verification Checkout Facility (VCF) allows interactive comparison of module results to store data as well as provides an intermediate checkout of the processor code. After validation using the VCF, the engineering modules and submodules were used to build a simple TTBE.

New Site Coefficients and Site Classification System Used in Recent Building Seismic Code Provisions

USGS Publications Warehouse

Dobry, R.; Borcherdt, R.D.; Crouse, C.B.; Idriss, I.M.; Joyner, W.B.; Martin, G.R.; Power, M.S.; Rinne, E.E.; Seed, R.B.

2000-01-01

Recent code provisions for buildings and other structures (1994 and 1997 NEHRP Provisions, 1997 UBC) have adopted new site amplification factors and a new procedure for site classification. Two amplitude-dependent site amplification factors are specified: Fa for short periods and Fv for longer periods. Previous codes included only a long period factor S and did not provide for a short period amplification factor. The new site classification system is based on definitions of five site classes in terms of a representative average shear wave velocity to a depth of 30 m (V?? s). This definition permits sites to be classified unambiguously. When the shear wave velocity is not available, other soil properties such as standard penetration resistance or undrained shear strength can be used. The new site classes denoted by letters A - E, replace site classes in previous codes denoted by S1 - S4. Site classes A and B correspond to hard rock and rock, Site Class C corresponds to soft rock and very stiff / very dense soil, and Site Classes D and E correspond to stiff soil and soft soil. A sixth site class, F, is defined for soils requiring site-specific evaluations. Both Fa and Fv are functions of the site class, and also of the level of seismic hazard on rock, defined by parameters such as Aa and Av (1994 NEHRP Provisions), Ss and S1 (1997 NEHRP Provisions) or Z (1997 UBC). The values of Fa and Fv decrease as the seismic hazard on rock increases due to soil nonlinearity. The greatest impact of the new factors Fa and Fv as compared with the old S factors occurs in areas of low-to-medium seismic hazard. This paper summarizes the new site provisions, explains the basis for them, and discusses ongoing studies of site amplification in recent earthquakes that may influence future code developments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

The 2015 IECC provides cost-effective savings for residential buildings in Arizona. Moving to the 2015 IECC from the 2009 IECC base code is cost-effective for residential buildings in all climate zones in Arizona.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

The 2015 IECC provides cost-effective savings for residential buildings in Hawaii. Moving to the 2015 IECC from the 2006 IECC base code is cost-effective for residential buildings in all climate zones in Hawaii.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendon, Vrushali V.; Zhao, Mingjie; Taylor, Zachary T.

The 2015 IECC provides cost-effective savings for residential buildings in Connecticut. Moving to the 2015 IECC from the 2009 IECC base code is cost-effective for residential buildings in all climate zones in Connecticut.

Energy Building Regulations: The Effect of the Federal Performance Standards on Building Code Administration and the Conservation of Energy in New Buildings.

ERIC Educational Resources Information Center

Kopper, William D.

1980-01-01

Explores the changes in the administration and enforcement of building regulations that will be engendered by the proposed federal energy building standards. Also evaluates the effectiveness of those standards in meeting congressional intent. Available from U.C. Davis Law Review, School of Law, Martin Luther King Jr. Hall, University of…

Development of Automated Procedures to Generate Reference Building Models for ASHRAE Standard 90.1 and India’s Building Energy Code and Implementation in OpenStudio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, Andrew; Haves, Philip; Jegi, Subhash

This paper describes a software system for automatically generating a reference (baseline) building energy model from the proposed (as-designed) building energy model. This system is built using the OpenStudio Software Development Kit (SDK) and is designed to operate on building energy models in the OpenStudio file format.

Liquefaction-induced lateral spreading in Oceano, California, during the 2003 San Simeon Earthquake

USGS Publications Warehouse

Holzer, Thomas L.; Noce, Thomas E.; Bennett, Michael J.; Di Alessandro, Carola; Boatwright, John; Tinsley, John C.; Sell, Russell W.; Rosenberg, Lewis I.

2004-01-01

The December 22, 2003, San Simeon, California, (M6.5) earthquake caused damage to houses, road surfaces, and underground utilities in Oceano, California. The community of Oceano is approximately 50 miles (80 km) from the earthquake epicenter. Damage at this distance from a M6.5 earthquake is unusual. To understand the causes of this damage, the U.S. Geological Survey conducted extensive subsurface exploration and monitoring of aftershocks in the months after the earthquake. The investigation included 37 seismic cone penetration tests, 5 soil borings, and aftershock monitoring from January 28 to March 7, 2004. The USGS investigation identified two earthquake hazards in Oceano that explain the San Simeon earthquake damage?site amplification and liquefaction. Site amplification is a phenomenon observed in many earthquakes where the strength of the shaking increases abnormally in areas where the seismic-wave velocity of shallow geologic layers is low. As a result, earthquake shaking is felt more strongly than in surrounding areas without similar geologic conditions. Site amplification in Oceano is indicated by the physical properties of the geologic layers beneath Oceano and was confirmed by monitoring aftershocks. Liquefaction, which is also commonly observed during earthquakes, is a phenomenon where saturated sands lose their strength during an earthquake and become fluid-like and mobile. As a result, the ground may undergo large permanent displacements that can damage underground utilities and well-built surface structures. The type of displacement of major concern associated with liquefaction is lateral spreading because it involves displacement of large blocks of ground down gentle slopes or towards stream channels. The USGS investigation indicates that the shallow geologic units beneath Oceano are very susceptible to liquefaction. They include young sand dunes and clean sandy artificial fill that was used to bury and convert marshes into developable lots. Most of the 2003 damage was caused by lateral spreading in two separate areas, one near Norswing Drive and the other near Juanita Avenue. The areas coincided with areas with the highest liquefaction potential found in Oceano. Areas with site amplification conditions similar to those in Oceano are particularly vulnerable to earthquakes. Site amplification may cause shaking from distant earthquakes, which normally would not cause damage, to increase locally to damaging levels. The vulnerability in Oceano is compounded by the widespread distribution of highly liquefiable soils that will reliquefy when ground shaking is amplified as it was during the San Simeon earthquake. The experience in Oceano can be expected to repeat because the region has many active faults capable of generating large earthquakes. In addition, liquefaction and lateral spreading will be more extensive for moderate-size earthquakes that are closer to Oceano than was the 2003 San Simeon earthquake. Site amplification and liquefaction can be mitigated. Shaking is typically mitigated in California by adopting and enforcing up-to-date building codes. Although not a guarantee of safety, application of these codes ensures that the best practice is used in construction. Building codes, however, do not always require the upgrading of older structures to new code requirements. Consequently, many older structures may not be as resistant to earthquake shaking as new ones. For older structures, retrofitting is required to bring them up to code. Seismic provisions in codes also generally do not apply to nonstructural elements such as drywall, heating systems, and shelving. Frequently, nonstructural damage dominates the earthquake loss. Mitigation of potential liquefaction in Oceano presently is voluntary for existing buildings, but required by San Luis Obispo County for new construction. Multiple mitigation procedures are available to individual property owners. These procedures typically involve either

Implementing energy standards for motors and buildings in the Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiel, S.; Busch, J.; Sanchez, C.

1998-07-01

The Philippines' master plan for energy makes cornerstones of energy standards for appliances, buildings, and motors in their energy efficiency effort. Significant progress has been made in implementing appliance standards for some products, but has lagged for others. This has been partly because the resources allocated have dictated a cautious deliberate approach. Products where there has been a lack of information about the respective markets have received lowest priority. Motors fall in this latter category. In their development of building codes, the Philippine government has also taken a cautious deliberate approach and is just now attending to the compliance ofmore » a commercial building energy performance standard that was enacted into law in 1994. This paper describes the results of recent new buildings and motor market assessments carried out in the Philippines, a survey of building energy code implementation in other countries, and how these products are being used to further implementation of energy standards in the Philippines. Lessons for other countries are drawn from this experience.« less

System and method for creating expert systems

NASA Technical Reports Server (NTRS)

Hughes, Peter M. (Inventor); Luczak, Edward C. (Inventor)

1998-01-01

A system and method provides for the creation of a highly graphical expert system without the need for programming in code. An expert system is created by initially building a data interface, defining appropriate Mission, User-Defined, Inferred, and externally-generated GenSAA (EGG) data variables whose data values will be updated and input into the expert system. Next, rules of the expert system are created by building appropriate conditions of the rules which must be satisfied and then by building appropriate actions of rules which are to be executed upon corresponding conditions being satisfied. Finally, an appropriate user interface is built which can be highly graphical in nature and which can include appropriate message display and/or modification of display characteristics of a graphical display object, to visually alert a user of the expert system of varying data values, upon conditions of a created rule being satisfied. The data interface building, rule building, and user interface building are done in an efficient manner and can be created without the need for programming in code.

Gate-to-gate Life-Cycle Inventory of Hardboard Production in North America

Treesearch

Richard Bergman

2014-01-01

Whole-building life-cycle assessments (LCAs) populated by life-cycle inventory (LCI) data are incorporated into environmental footprint software tools for establishing green building certification by building professionals and code. However, LCI data on some wood building products are still needed to help fill gaps in the data and thus provide a more complete picture...

10 CFR 434.506 - Use of the reference building to determine the energy cost budget.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Use of the reference building to determine the energy cost budget. 434.506 Section 434.506 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance...

10 CFR 434.504 - Use of the prototype building to determine the energy cost budget.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Use of the prototype building to determine the energy cost budget. 434.504 Section 434.504 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY CODE FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance...

31 CFR 11.6 - Terms of permit.

Code of Federal Regulations, 2012 CFR

2012-07-01

... vending facilities shall be operated in compliance with applicable health, sanitation, and building codes... normal cleaning, maintenance, and repair of the building structure in and adjacent to the vending...

31 CFR 11.6 - Terms of permit.

Code of Federal Regulations, 2011 CFR

2011-07-01

... vending facilities shall be operated in compliance with applicable health, sanitation, and building codes... normal cleaning, maintenance, and repair of the building structure in and adjacent to the vending...

31 CFR 11.6 - Terms of permit.

Code of Federal Regulations, 2014 CFR

2014-07-01

... vending facilities shall be operated in compliance with applicable health, sanitation, and building codes... normal cleaning, maintenance, and repair of the building structure in and adjacent to the vending...

34 CFR 395.35 - Terms of permit.

Code of Federal Regulations, 2012 CFR

2012-07-01

... health, sanitation, and building codes or ordinances. (e) The permit shall further provide that... to the State licensing agency for normal cleaning, maintenance, and repair of the building structure...

34 CFR 395.35 - Terms of permit.

Code of Federal Regulations, 2014 CFR

2014-07-01

... health, sanitation, and building codes or ordinances. (e) The permit shall further provide that... to the State licensing agency for normal cleaning, maintenance, and repair of the building structure...

The Modular Factor.

ERIC Educational Resources Information Center

Cray, Dan

1994-01-01

Discusses the tradeoff of speed and movability versus costs when using relocatable buildings to solve educational space needs. Concluding comments address building-code compliance issues driving up expenses and impacting facility planning.(GR)

Multibody dynamics model building using graphical interfaces

NASA Technical Reports Server (NTRS)

Macala, Glenn A.

1989-01-01

In recent years, the extremely laborious task of manually deriving equations of motion for the simulation of multibody spacecraft dynamics has largely been eliminated. Instead, the dynamicist now works with commonly available general purpose dynamics simulation programs which generate the equations of motion either explicitly or implicitly via computer codes. The user interface to these programs has predominantly been via input data files, each with its own required format and peculiarities, causing errors and frustrations during program setup. Recent progress in a more natural method of data input for dynamics programs: the graphical interface, is described.

The receptive field is dead. Long live the receptive field?

PubMed Central

Fairhall, Adrienne

2014-01-01

Advances in experimental techniques, including behavioral paradigms using rich stimuli under closed loop conditions and the interfacing of neural systems with external inputs and outputs, reveal complex dynamics in the neural code and require a revisiting of standard concepts of representation. High-throughput recording and imaging methods along with the ability to observe and control neuronal subpopulations allow increasingly detailed access to the neural circuitry that subserves these representations and the computations they support. How do we harness theory to build biologically grounded models of complex neural function? PMID:24618227