Alpha-channeling simulation experiment in the DIII-D tokamak.

PubMed

Wong, K L; Budny, R; Nazikian, R; Petty, C C; Greenfield, C M; Heidbrink, W W; Ruskov, E

2004-08-20

Alfvén instabilities can reduce the central magnetic shear via redistribution of energetic ions. They can sustain a steady state internal transport barrier as demonstrated in this DIII-D tokamak experiment. Improvement in burning plasma performance based on this mechanism is discussed.

Plasma wall interaction, a key issue on the way to a steady state burning fusion device

NASA Astrophysics Data System (ADS)

Philipps, V.

2006-04-01

The International Tokamak Experimental Reactor (ITER), the first burning fusion plasma experiment based on the tokamak principle, is ready for construction. It is based on many years of fusion research resulting in a robust design in most of the areas. Present day fusion research concentrates on the remaining critical issues which are, to a large extent, connected with processes of plasma wall interaction. This is mainly due to extended duty cycle and the increase of the plasma stored energy in comparison with present-day machines. Critical topics are the lifetime of the plasma facing components (PFC) and the long-term tritium retention. These processes are controlled mainly by material erosion, both during steady state operation and transient power losses (disruptions and edge localized modes (ELMs)) and short- and long-range material migration and re-deposition. The extrapolation from present-day 'full carbon wall' devices suggests that the long-term tritium retention in a burning fusion device would be unacceptably high under these conditions allowing for only an unacceptable limited number of pulses in a D T mixture. As a consequence of this, research activities have been strengthened to understand in more detail the underlying processes of material erosion and re-deposition, to develop methods to remove retained tritium from the PFCs and remote areas of a fusion device and to explore these processes and the plasma performance in more detail with metallic PFC, such as beryllium (Be) and tungsten (W), which are foreseen for the ITER experiment. This paper outlines the main physical mechanisms leading to material erosion, migration and re-deposition and the associated fuel retention. It addresses the experimental database in these areas and describes the further research strategies that will be needed to tackle critical issues.

SciDAC GSEP: Gyrokinetic Simulation of Energetic Particle Turbulence and Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Zhihong

Energetic particle (EP) confinement is a key physics issue for burning plasma experiment ITER, the crucial next step in the quest for clean and abundant energy, since ignition relies on self-heating by energetic fusion products (α-particles). Due to the strong coupling of EP with burning thermal plasmas, plasma confinement property in the ignition regime is one of the most uncertain factors when extrapolating from existing fusion devices to the ITER tokamak. EP population in current tokamaks are mostly produced by auxiliary heating such as neutral beam injection (NBI) and radio frequency (RF) heating. Remarkable progress in developing comprehensive EP simulationmore » codes and understanding basic EP physics has been made by two concurrent SciDAC EP projects GSEP funded by the Department of Energy (DOE) Office of Fusion Energy Science (OFES), which have successfully established gyrokinetic turbulence simulation as a necessary paradigm shift for studying the EP confinement in burning plasmas. Verification and validation have rapidly advanced through close collaborations between simulation, theory, and experiment. Furthermore, productive collaborations with computational scientists have enabled EP simulation codes to effectively utilize current petascale computers and emerging exascale computers. We review here key physics progress in the GSEP projects regarding verification and validation of gyrokinetic simulations, nonlinear EP physics, EP coupling with thermal plasmas, and reduced EP transport models. Advances in high performance computing through collaborations with computational scientists that enable these large scale electromagnetic simulations are also highlighted. These results have been widely disseminated in numerous peer-reviewed publications including many Phys. Rev. Lett. papers and many invited presentations at prominent fusion conferences such as the biennial International Atomic Energy Agency (IAEA) Fusion Energy Conference and the annual meeting of the American Physics Society, Division of Plasma Physics (APS-DPP).« less

Pellet fuelling requirements to allow self-burning on a helical-type fusion reactor

NASA Astrophysics Data System (ADS)

Sakamoto, R.; Miyazawa, J.; Yamada, H.; Masuzaki, S.; Sagara, A.; the FFHR Design Group

2012-08-01

Pellet refuelling conditions to sustain a self-burning plasma have been investigated by extrapolating the confinement property of the LHD plasma, which appears to be governed by a gyro-Bohm-type confinement property. The power balance of the burning plasma is calculated taking into account the profile change with pellet deposition and subsequent density relaxation. A self-burning plasma is achieved within the scope of conventional pellet injection technology. However, a very small burn-up rate of 0.18% is predicted. Higher velocity pellet injection is effective in improving the burn-up rate by deepening particle deposition, whereas deep fuelling leads to undesirable fluctuation of the fusion output.

Radiation reaction in fusion plasmas.

PubMed

Hazeltine, R D; Mahajan, S M

2004-10-01

The effects of a radiation reaction on thermal electrons in a magnetically confined plasma, with parameters typical of planned burning plasma experiments, are studied. A fully relativistic kinetic equation that includes the radiation reaction is derived. The associated rate of phase-space contraction is computed and the relative importance of the radiation reaction in phase space is estimated. A consideration of the moments of the radiation reaction force show that its effects are typically small in reactor-grade confined plasmas, but not necessarily insignificant.

Effects of magnetization on fusion product trapping and secondary neutron spectra

DOE PAGES

Knapp, Patrick F.; Schmit, Paul F.; Hansen, Stephanie B.; ...

2015-05-14

In magnetizing the fusion fuel in inertial confinement fusion (ICF) systems, we found that the required stagnation pressure and density can be relaxed dramatically. This happens because the magnetic field insulates the hot fuel from the cold pusher and traps the charged fusion burn products. This trapping allows the burn products to deposit their energy in the fuel, facilitating plasma self-heating. Here, we report on a comprehensive theory of this trapping in a cylindrical DD plasma magnetized with a purely axial magnetic field. Using this theory, we are able to show that the secondary fusion reactions can be used tomore » infer the magnetic field-radius product, BR, during fusion burn. This parameter, not ρR, is the primary confinement parameter in magnetized ICF. Using this method, we analyze data from recent Magnetized Liner InertialFusion experiments conducted on the Z machine at Sandia National Laboratories. Furthermore, we show that in these experiments BR ≈ 0.34(+0.14/-0.06) MG · cm, a ~ 14× increase in BR from the initial value, and confirming that the DD-fusion tritons are magnetized at stagnation. Lastly, this is the first experimental verification of charged burn product magnetization facilitated by compression of an initial seed magnetic flux.« less

Development of a real-time simulation tool towards self-consistent scenario of plasma start-up and sustainment on helical fusion reactor FFHR-d1

NASA Astrophysics Data System (ADS)

Goto, T.; Miyazawa, J.; Sakamoto, R.; Suzuki, Y.; Suzuki, C.; Seki, R.; Satake, S.; Huang, B.; Nunami, M.; Yokoyama, M.; Sagara, A.; the FFHR Design Group

2017-06-01

This study closely investigates the plasma operation scenario for the LHD-type helical reactor FFHR-d1 in view of MHD equilibrium/stability, neoclassical transport, alpha energy loss and impurity effect. In 1D calculation code that reproduces the typical pellet discharges in LHD experiments, we identify a self-consistent solution of the plasma operation scenario which achieves steady-state sustainment of the burning plasma with a fusion gain of Q ~ 10 was found within the operation regime that has been already confirmed in LHD experiment. The developed calculation tool enables systematic analysis of the operation regime in real time.

Plasma Stopping Power Measurements Relevant to Inertial Confinement Fusion

NASA Astrophysics Data System (ADS)

McEvoy, Aaron; Herrmann, Hans; Kim, Yongho; Hoffman, Nelson; Schmitt, Mark; Rubery, Michael; Garbett, Warren; Horsfield, Colin; Gales, Steve; Zylstra, Alex; Gatu Johnson, Maria; Frenje, Johan; Petrasso, Richard; Marshall, Frederic; Batha, Steve

2015-11-01

Ignition in inertial confinement fusion (ICF) experiments may be achieved if the alpha particle energy deposition results in a thermonuclear burn wave induced in the dense DT fuel layer surrounding the hotspot. As such, understanding the physics of particle energy loss in a plasma is of critical importance to designing ICF experiments. Experiments have validated various stopping power models under select ne and Te conditions, however there remain unexplored regimes where models predict differing rates of energy deposition. An upcoming experiment at the Omega laser facility will explore charged particle stopping in CH plastic capsule ablators across a range of plasma conditions (ne between 1024 cm-3 and 1025 cm-3 and Te on the order of hundreds of eV). Plasma conditions will be measured using x-ray and gamma ray diagnostics, while plasma stopping power will be measured using charged particle energy loss measurements. Details on the experiment and the theoretical models to be tested will be presented.

First downscattered neutron images from Inertial Confinement Fusion experiments at the National Ignition Facility

NASA Astrophysics Data System (ADS)

Guler, Nevzat; Aragonez, Robert J.; Archuleta, Thomas N.; Batha, Steven H.; Clark, David D.; Clark, Deborah J.; Danly, Chris R.; Day, Robert D.; Fatherley, Valerie E.; Finch, Joshua P.; Gallegos, Robert A.; Garcia, Felix P.; Grim, Gary; Hsu, Albert H.; Jaramillo, Steven A.; Loomis, Eric N.; Mares, Danielle; Martinson, Drew D.; Merrill, Frank E.; Morgan, George L.; Munson, Carter; Murphy, Thomas J.; Oertel, John A.; Polk, Paul J.; Schmidt, Derek W.; Tregillis, Ian L.; Valdez, Adelaida C.; Volegov, Petr L.; Wang, Tai-Sen F.; Wilde, Carl H.; Wilke, Mark D.; Wilson, Douglas C.; Atkinson, Dennis P.; Bower, Dan E.; Drury, Owen B.; Dzenitis, John M.; Felker, Brian; Fittinghoff, David N.; Frank, Matthias; Liddick, Sean N.; Moran, Michael J.; Roberson, George P.; Weiss, Paul; Buckles, Robert A.; Cradick, Jerry R.; Kaufman, Morris I.; Lutz, Steve S.; Malone, Robert M.; Traille, Albert

2013-11-01

Inertial Confinement Fusion experiments at the National Ignition Facility (NIF) are designed to understand and test the basic principles of self-sustaining fusion reactions by laser driven compression of deuterium-tritium (DT) filled cryogenic plastic (CH) capsules. The experimental campaign is ongoing to tune the implosions and characterize the burning plasma conditions. Nuclear diagnostics play an important role in measuring the characteristics of these burning plasmas, providing feedback to improve the implosion dynamics. The Neutron Imaging (NI) diagnostic provides information on the distribution of the central fusion reaction region and the surrounding DT fuel by collecting images at two different energy bands for primary (13-15 MeV) and downscattered (10-12 MeV) neutrons. From these distributions, the final shape and size of the compressed capsule can be estimated and the symmetry of the compression can be inferred. The first downscattered neutron images from imploding ICF capsules are shown in this paper.

Treatment in the healing of burns with a cold plasma source

PubMed Central

Betancourt-Ángeles, Mario; Peña-Eguiluz, Rosendo; López-Callejas, Régulo; Domínguez-Cadena, Nicasio Alberto; Mercado-Cabrera, Antonio; Muñoz-Infante, Jorge; Rodríguez-Méndez, Benjamín Gonzalo; Valencia-Alvarado, Raúl; Moreno-Tapia, José Alberto

2017-01-01

A cold plasma produced with helium gas was applied to two second-degree burns produced with boiling oil. These burns were located on a thigh and a shin of a 59-years-old male person. After the first treatment as benefit the patient neither presented itching nor pain and, after the second treatment, the patient presented new tissue. This result opens the possibilities of the application of a cold plasma source to health burns. PMID:29348977

Towards a better understanding of critical gradients and near-marginal turbulence in burning plasma conditions

NASA Astrophysics Data System (ADS)

Holland, C.; Candy, J.; Howard, N. T.

2017-10-01

Developing accurate predictive transport models of burning plasma conditions is essential for confident prediction and optimization of next step experiments such as ITER and DEMO. Core transport in these plasmas is expected to be very small in gyroBohm-normalized units, such that the plasma should lie close to the critical gradients for onset of microturbulence instabilities. We present recent results investigating the scaling of linear critical gradients of ITG, TEM, and ETG modes as a function of parameters such as safety factor, magnetic shear, and collisionality for nominal conditions and geometry expected in ITER H-mode plasmas. A subset of these results is then compared against predictions from nonlinear gyrokinetic simulations, to quantify differences between linear and nonlinear thresholds. As part of this study, linear and nonlinear results from both GYRO and CGYRO codes will be compared against each other, as well as to predictions from the quasilinear TGLF model. Challenges arising from near-marginal turbulence dynamics are addressed. This work was supported by the US Department of Energy under US DE-SC0006957.

[Clinical study on the postburn change in the hypothalamus-pituitary-adrenal hormones in severely burned patients].

PubMed

Li, Hong-mian; Liang, Zi-qian; Luo, Zuo-jie

2003-06-01

To investigate the postburn dynamic changes in the hypothalamus-pituitary-adrenal hormones in severely burned patients. Fifty burn patients were enrolled in the study. The plasma contents of total GC (cortisol), ACTH and aldosterone (ALDO) and urinary contents of 17-OHO and 17-KS were determined with radio-immunological assay (RIA) method after burn injury to compare with the normal values which were well established clinically. The postburn plasma and urinary contents of the above indices were increased evidently with two peak values in shock and infectious stages, whilst the majority of he indices were lower than the normal values after 6 postburn weeks (PBWs). The values of these hormones were the lowest in dying patients. On the other hand, the values approached normal levels in those patients whose burn wounds were healing. Increases of the plasma and urinary levels of hypothalamus-pituitary -adrenal hormones in severely burned patients were constantly seen. Burn shock and infection seemed to be the two major factors in inducing postburn stress reaction in burn victims. Abrupt decrease of the hormone levels in plasma and or urine indicated adrenal failure predicting a poor prognosis of the burn patients.

Perspectives for the high field approach in fusion research and advances within the Ignitor Program

NASA Astrophysics Data System (ADS)

Coppi, B.; Airoldi, A.; Albanese, R.; Ambrosino, G.; Belforte, G.; Boggio-Sella, E.; Cardinali, A.; Cenacchi, G.; Conti, F.; Costa, E.; D'Amico, A.; Detragiache, P.; De Tommasi, G.; DeVellis, A.; Faelli, G.; Ferraris, P.; Frattolillo, A.; Giammanco, F.; Grasso, G.; Lazzaretti, M.; Mantovani, S.; Merriman, L.; Migliori, S.; Napoli, R.; Perona, A.; Pierattini, S.; Pironti, A.; Ramogida, G.; Rubinacci, G.; Sassi, M.; Sestero, A.; Spillantini, S.; Tavani, M.; Tumino, A.; Villone, F.; Zucchi, L.

2015-05-01

The Ignitor Program maintains the objective of approaching D-T ignition conditions by incorporating systematical advances made with relevant high field magnet technology and with experiments on high density well confined plasmas in the present machine design. An additional objective is that of charting the development of the high field line of experiments that goes from the Alcator machine to the ignitor device. The rationale for this class of experiments, aimed at producing poloidal fields with the highest possible values (compatible with proven safety factors of known plasma instabilities) is given. On the basis of the favourable properties of high density plasmas produced systematically by this line of machines, the envisioned future for the line, based on novel high field superconducting magnets, includes the possibility of investigating more advanced fusion burn conditions than those of the D-T plasmas for which Ignitor is designed. Considering that a detailed machine design has been carried out (Coppi et al 2013 Nucl. Fusion 53 104013), the advances made in different areas of the physics and technology that are relevant to the Ignitor project are reported. These are included within the following sections of the present paper: main components issues, assembly and welding procedures; robotics criteria; non-linear feedback control; simulations with three-dimensional structures and disruption studies; ICRH and dedicated diagnostics systems; anomalous transport processes including self-organization for fusion burning regimes and the zero-dimensional model; tridimensional structures of the thermonuclear instability and control provisions; superconducting components of the present machine; envisioned experiments with high field superconducting magnets.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahlburg, Jill; Corones, James; Batchelor, Donald

Fusion is potentially an inexhaustible energy source whose exploitation requires a basic understanding of high-temperature plasmas. The development of a science-based predictive capability for fusion-relevant plasmas is a challenge central to fusion energy science, in which numerical modeling has played a vital role for more than four decades. A combination of the very wide range in temporal and spatial scales, extreme anisotropy, the importance of geometric detail, and the requirement of causality which makes it impossible to parallelize over time, makes this problem one of the most challenging in computational physics. Sophisticated computational models are under development for many individualmore » features of magnetically confined plasmas and increases in the scope and reliability of feasible simulations have been enabled by increased scientific understanding and improvements in computer technology. However, full predictive modeling of fusion plasmas will require qualitative improvements and innovations to enable cross coupling of a wider variety of physical processes and to allow solution over a larger range of space and time scales. The exponential growth of computer speed, coupled with the high cost of large-scale experimental facilities, makes an integrated fusion simulation initiative a timely and cost-effective opportunity. Worldwide progress in laboratory fusion experiments provides the basis for a recent FESAC recommendation to proceed with a burning plasma experiment (see FESAC Review of Burning Plasma Physics Report, September 2001). Such an experiment, at the frontier of the physics of complex systems, would be a huge step in establishing the potential of magnetic fusion energy to contribute to the world’s energy security. An integrated simulation capability would dramatically enhance the utilization of such a facility and lead to optimization of toroidal fusion plasmas in general. This science-based predictive capability, which was cited in the FESAC integrated planning document (IPPA, 2000), represents a significant opportunity for the DOE Office of Science to further the understanding of fusion plasmas to a level unparalleled worldwide.« less

Comparison of the outcome of burn patients using acute-phase plasma base deficit.

PubMed

Salehi, S H; As'adi, K; Mousavi, J

2011-12-31

Background. In recent years, plasma base deficit has been used as a marker to determine the status of tissue perfusion in trauma patients and also to predict the outcome of these patients. This study was performed to investigate the effect of plasma base deficit in predicting burn patient outcome. Methods. This prospective cohort study was performed from October 2009 to October 2010 in the acute phase of burn patients who were admitted within 6 h post-injury to Motahari Burn Hospital in Iran. The patients were divided into two groups based on the plasma base deficit in the first 24 h post-injury: group A, in which the mean plasma base deficit was less than or equal to -6 (more negative), and group B, in which the mean plasma base deficit greater than -6. Statistical analysis was performed using SPSS v.16 software. Results. Thirty-eight patients were enrolled in each group. The mean plasma base deficit in group A (-7.76 ± 2.18 mmol) was significantly less than that in group B (-1.19 ± 2.82) mmol (p < 0.05). Although there was no significant difference between the mean of fluid resuscitation and urine output in the first 24 h after injury between the two groups (p > 0.05) and despite removal of interfering factors, there were significant differences between the systemic inflammatory response syndrome and the multiple organ dysfunction syndrome score and the percentage of sepsis between the two groups (p < 0.05). The mortality rate in group A (63.2%) was significantly higher than that in group B (36.8%) (p > 0.05). Conclusion. The plasma base deficit can be used as a valuable marker in the resuscitation of burn patients, along with clinical criteria. Physiological indicators (burn percentage, age, and mucosal burns) are not sufficient to predict mortality and morbidity in burn patients, and it is necessary to investigate the role of biochemical markers such as base deficit in determining the final outcome of burn patients.

Recent Advances in Studies of Ionospheric Modification Using Rocket Exhaust (Invited)

NASA Astrophysics Data System (ADS)

Bernhardt, P. A.

2009-12-01

Rocket exhaust interacts with the ionosphere to produce a wide range of disturbances. A ten second burn of the Orbital Maneuver Subsystem (OMS) engines on the Space Shuttle deposits over 1 Giga Joule of energy into the upper atmosphere. The exhaust vapors travel at speeds between 4.7 and 10.7 km/s coupling momentum into the ions by both collisions and charge exchange. Long-lived plasma irregularities are formed by the artificial hypersonic “neutral wind” passing through the ionosphere. Charge exchange between the fast neutrals and the ambient ions yields high-speed ion beams that excite electro-static plasma waves. Ground based radar has been used to detect both field aligned irregularities and electrostatic turbulence driven by the Space Shuttle OMS exhaust. Molecular ions produced by the charge exchange with molecules in the rocket exhaust recombine with a time scale of 10 minutes leaving a residual plasma depression. This ionospheric “hole” fills in by ambipolar diffusion leaving a depleted magnetic flux tube. This large scale reduction in Pedersen conductivity can provide a seed for plasma interchange instabilities. For instance, a rocket firing on the bottom side of the ionosphere near the equator can trigger a Rayleigh-Taylor instability that is naturally seen as equatorial Spread-F. The Naval Research Laboratory has been exploring these phenomena with dedicated burns of the Space Shuttle OMS engines and exhaust releases from rockets. The Shuttle Ionospheric Modification with Pulsed Localized Exhaust (SIMPLEX) series of experiments uses ground radars to probe the ionosphere affected by dedicated burns of the Space Shuttle OMS engines. Radars located at Millstone Hill, Massachusetts; Arecibo, Puerto Rico; Jicamarca, Peru; Kwajalein, Marshall Island; and Alice Springs, Australia have participated in the SIMPLEX program. A companion program called Shuttle Exhaust Ionospheric Turbulence Experiment has or will use satellites to fly through the turbulence ionosphere produced by Space Shuttle Exhaust. This program is employing the Air Force Research Laboratory C/NOFS and the Canadian CASSIOPE/EPoP satellites to make in situ measurements of Space Shuttle exhaust effects. Finally, NRL is conducting the Charged Aerosol Release Experiment which employs a solid rocket motor to modify the ionosphere using supersonic particulate injection and dusty plasma formation. Both the theoretic basis for these experiments and as summary of the experimental results will be presented.

Energetic particle-driven compressional Alfvén eigenmodes and prospects for ion cyclotron emission studies in fusion plasmas

DOE PAGES

Gorelenkov, N. N.

2016-10-01

As a fundamental plasma oscillation the compressional Alfvén waves (CAW) are interesting for plasma scientists both academically and in applications for fusion plasmas. They are believed to be responsible for the ion cyclotron emission (ICE) observed in many tokamaks. The theory of CAW and ICE was significantly advanced at the end of 20th century in particular motivated by first DT experiments on TFTR and subsequent JET DT experimental studies. More recently, ICE theory was advanced by ST (or spherical torus) experiments with the detailed theoretical and experimental studies of the properties of each instability signal. There the instability responsible formore » ICE signals previously indistinguishable in high aspect ratio tokamaks became the subjects of experimental studies. We discuss further the prospects of ICE theory and its applications for future burning plasma (BP) experiments such as the ITER tokamak-reactor prototype being build in France where neutrons and gamma rays escaping the plasma create extremely challenging conditions for fusion alpha particle diagnostics.a« less

Isotope effects on L-H threshold and confinement in tokamak plasmas

NASA Astrophysics Data System (ADS)

Maggi, C. F.; Weisen, H.; Hillesheim, J. C.; Chankin, A.; Delabie, E.; Horvath, L.; Auriemma, F.; Carvalho, I. S.; Corrigan, G.; Flanagan, J.; Garzotti, L.; Keeling, D.; King, D.; Lerche, E.; Lorenzini, R.; Maslov, M.; Menmuir, S.; Saarelma, S.; Sips, A. C. C.; Solano, E. R.; Belonohy, E.; Casson, F. J.; Challis, C.; Giroud, C.; Parail, V.; Silva, C.; Valisa, M.; Contributors, JET

2018-01-01

The dependence of plasma transport and confinement on the main hydrogenic ion isotope mass is of fundamental importance for understanding turbulent transport and, therefore, for accurate extrapolations of confinement from present tokamak experiments, which typically use a single hydrogen isotope, to burning plasmas such as ITER, which will operate in deuterium-tritium mixtures. Knowledge of the dependence of plasma properties and edge transport barrier formation on main ion species is critical in view of the initial, low-activation phase of ITER operations in hydrogen or helium and of its implications on the subsequent operation in deuterium-tritium. The favourable scaling of global energy confinement time with isotope mass, which has been observed in many tokamak experiments, remains largely unexplained theoretically. Moreover, the mass scaling observed in experiments varies depending on the plasma edge conditions. In preparation for upcoming deuterium-tritium experiments in the JET tokamak with the ITER-like Be/W Wall (JET-ILW), a thorough experimental investigation of isotope effects in hydrogen, deuterium and tritium plasmas is being carried out, in order to provide stringent tests of plasma energy, particle and momentum transport models. Recent hydrogen and deuterium isotope experiments in JET-ILW on L-H power threshold, L-mode and H-mode confinement are reviewed and discussed in the context of past and more recent isotope experiments in tokamak plasmas, highlighting common elements as well as contrasting observations that have been reported. The experimental findings are discussed in the context of fundamental aspects of plasma transport models.

Understanding and predicting the dynamics of tokamak discharges during startup and rampdown

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jackson, G. L.; Politzer, P. A.; Humphreys, D. A.

Understanding the dynamics of plasma startup and termination is important for present tokamaks and for predictive modeling of future burning plasma devices such as ITER. We report on experiments in the DIII-D tokamak that explore the plasma startup and rampdown phases and on the benchmarking of transport models. Key issues have been examined such as plasma initiation and burnthrough with limited inductive voltage and achieving flattop and maximum burn within the technical limits of coil systems and their actuators while maintaining the desired q profile. Successful rampdown requires scenarios consistent with technical limits, including controlled H-L transitions, while avoiding verticalmore » instabilities, additional Ohmic transformer flux consumption, and density limit disruptions. Discharges were typically initiated with an inductive electric field typical of ITER, 0.3 V/m, most with second harmonic electron cyclotron assist. A fast framing camera was used during breakdown and burnthrough of low Z impurity charge states to study the formation physics. An improved 'large aperture' ITER startup scenario was developed, and aperture reduction in rampdown was found to be essential to avoid instabilities. Current evolution using neoclassical conductivity in the CORSICA code agrees with rampup experiments, but the prediction of the temperature and internal inductance evolution using the Coppi-Tang model for electron energy transport is not yet accurate enough to allow extrapolation to future devices.« less

Nonlinear Burn Control in Tokamaks using Heating, Non-axisymmetric Magnetic Fields, Isotopic fueling and Impurity injection

NASA Astrophysics Data System (ADS)

Pajares, Andres; Schuster, Eugenio

2016-10-01

Plasma density and temperature regulation in future tokamaks such as ITER is arising as one of the main problems in nuclear-fusion control research. The problem, known as burn control, is to regulate the amount of fusion power produced by the burning plasma while avoiding thermal instabilities. Prior work in the area of burn control considered different actuators, such as modulation of the auxiliary power, modulation of the fueling rate, and controlled impurity injection. More recently, the in-vessel coil system was suggested as a feasible actuator since it has the capability of modifying the plasma confinement by generating non-axisymmetric magnetic fields. In this work, a comprehensive, model-based, nonlinear burn control strategy is proposed to integrate all the previously mentioned actuators. A model to take into account the influence of the in-vessel coils on the plasma confinement is proposed based on the plasma collisionality and the density. A simulation study is carried out to show the capability of the controller to drive the system between different operating points while rejecting perturbations. Supported by the US DOE under DE-SC0010661.

Control of plasma stored energy for burn control using DIII-D in-vessel coils

DOE PAGES

Hawryluk, Richard J.; Eidietis, Nicholas W.; Grierson, Brian A.; ...

2015-04-09

A new approach has been experimentally demonstrated to control the stored energy by applying a non-axisymmetric magnetic field using the DIII-D in-vessel coils to modify the energy confinement time. In future burning plasma experiments as well as magnetic fusion energy power plants, various concepts have been proposed to control the fusion power. The fusion power in a power plant operating at high gain can be related to the plasma stored energy and hence, is a strong function of the energy confinement time. Thus, an actuator that modifies the confinement time can be used to adjust the fusion power. In relativelymore » low collisionality DIII-D discharges, the application of nonaxisymmetric magnetic fields results in a decrease in confinement time and density pumpout. Furthermore, gas puffing was used to compensate the density pumpout in the pedestal while control of the stored energy was demonstrated by the application of non-axisymmetric fields.« less

Cystathionine-gamma-lyase deficient mice are protected against the development of multiorgan failure and exhibit reduced inflammatory response during burn.

PubMed

Ahmad, Akbar; Druzhyna, Nadiya; Szabo, Csaba

2017-08-01

Considering the role of H 2 S in critical illness, the aim of this study was to compare the outcome of burn in wild-type mice and in mice deficient in CSE, one of the principal mammalian H 2 S-generating enzymes. Animals were subjected to scald burn. Outcome variables included indices of organ injury, clinical chemistry parameters and plasma levels of inflammatory mediators. Plasma levels of H 2 S significantly increased in response to burn in wild-type mice, but remained unchanged in CSE -/- mice. Expression of the three H 2 S-producing enzymes (CSE, CBS and 3-MST) in the lung and liver, and the capacity of tissue homogenates to produce H 2 S, however, was not affected by burn. In CSE deficient mice there was a significant amelioration of burn-induced accumulation of myeloperoxidase levels in heart, lung, liver and kidney and significantly lower degree of malon dialdehyde accumulation in the heart, lung and kidney than in wild-type mice. CSE deficient mice, compared to wild-type mice, showed a significant attenuation of the burn-induced elevation in circulating alkaline aminotransferase and blood urea nitrogen and creatinine levels, indicative of protective effects of CSE deficiency against burn-induced hepatic, and renal functional impairment. Multiple burn-induced inflammatory mediators (TNF-α, IL-1β, IL-4, IL-6, IL-10 and IL-12) were significantly lower in the plasma of CSE -/- animals after burn than in the plasma of wild-type controls subjected to burns. In conclusion, CSE deficiency improves organ function and attenuates the inflammatory response in a murine model of burn. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Simulation of Fusion Plasmas

ScienceCinema

Holland, Chris [UC San Diego, San Diego, California, United States

2017-12-09

The upcoming ITER experiment (www.iter.org) represents the next major milestone in realizing the promise of using nuclear fusion as a commercial energy source, by moving into the “burning plasma” regime where the dominant heat source is the internal fusion reactions. As part of its support for the ITER mission, the US fusion community is actively developing validated predictive models of the behavior of magnetically confined plasmas. In this talk, I will describe how the plasma community is using the latest high performance computing facilities to develop and refine our models of the nonlinear, multiscale plasma dynamics, and how recent advances in experimental diagnostics are allowing us to directly test and validate these models at an unprecedented level.

Imipenem in burn patients: pharmacokinetic profile and PK/PD target attainment.

PubMed

Gomez, David S; Sanches-Giraud, Cristina; Silva, Carlindo V; Oliveira, Amanda M Ribas Rosa; da Silva, Joao Manoel; Gemperli, Rolf; Santos, Silvia R C J

2015-03-01

Unpredictable pharmacokinetics (PK) in burn patients may result in plasma concentrations below concentrations that are effective against common pathogens. The present study evaluated the imipenem PK profile and pharmacokinetic/pharmacodynamics (PK/PD) correlation in burn patients. Fifty-one burn patients, 38.7 years of age (mean), 68.0 kg, 36.3% total burn surface area (TBSA), of whom 84% (43/51) exhibited thermal injury, 63% inhalation injury and 16% electrical injury (8/51), all of whom were receiving imipenem treatment were investigated. Drug plasma monitoring, PK study (120 sets of plasma levels) and PK/PD correlation were performed in a series of blood samples. Only 250 μl of plasma samples were required for drug plasma measurements using the ultra filtration technique for the purification of biological matrix and quantification using liquid chromatography. Probability of target attainment (PTA) was calculated using a PD target of 40% free drug concentrations above the minimum inhibitory concentration (40%fT>MIC). Significant differences in PK parameters (medians), such as biological half-life (2.2 vs 5.5 h), plasma clearance (16.2 vs 1.4 l h(-1)) and volume of distribution (0.86 vs 0.19 l kg(-1)), were registered in burn patients via comparisons of set periods with normal renal function against periods of renal failure. Correlations between creatinine clearance and total body plasma clearance were also obtained. In addition, the PK profile did not change according to TBSA during sets when renal function was preserved. PTA was >89% for MIC values up to 4 mg l(-1). In conclusion, imipenem efficacy for the control of hospital infection on the basis of PK/PD correlation was guaranteed for burn in patients at the recommended dose regimens for normal renal function (31.1±9.7 mg kg(-1) daily), but the daily dose must be reduced to 17.2±9.7 mg kg(-1) during renal failure to avoid neurotoxicity.

Burning plasma regime for Fussion-Fission Research Facility

NASA Astrophysics Data System (ADS)

Zakharov, Leonid E.

2010-11-01

The basic aspects of burning plasma regimes of Fusion-Fission Research Facility (FFRF, R/a=4/1 m/m, Ipl=5 MA, Btor=4-6 T, P^DT=50-100 MW, P^fission=80-4000 MW, 1 m thick blanket), which is suggested as the next step device for Chinese fusion program, are presented. The mission of FFRF is to advance magnetic fusion to the level of a stationary neutron source and to create a technical, scientific, and technology basis for the utilization of high-energy fusion neutrons for the needs of nuclear energy and technology. FFRF will rely as much as possible on ITER design. Thus, the magnetic system, especially TFC, will take advantage of ITER experience. TFC will use the same superconductor as ITER. The plasma regimes will represent an extension of the stationary plasma regimes on HT-7 and EAST tokamaks at ASIPP. Both inductive discharges and stationary non-inductive Lower Hybrid Current Drive (LHCD) will be possible. FFRF strongly relies on new, Lithium Wall Fusion (LiWF) plasma regimes, the development of which will be done on NSTX, HT-7, EAST in parallel with the design work. This regime will eliminate a number of uncertainties, still remaining unresolved in the ITER project. Well controlled, hours long inductive current drive operation at P^DT=50-100 MW is predicted.

INTERIOR VIEW, LOOKING SOUTHWEST, WITH PLASMA ARC BURNING MACHINE (GALT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING SOUTHWEST, WITH PLASMA ARC BURNING MACHINE (GALT INDUSTRIES) WHICH CUTS STEEL SHAPES AND OPERATOR PHILIP WILLOUBY. - O'Neal Steel, Incorporated, Fabrication Shop, 744 Forty-first Avenue North, Birmingham, Jefferson County, AL

Soluble Suppression of Tumorigenicity-2 Predicts Hospital Mortality in Burn Patients: An Observational Prospective Cohort Pilot Study.

PubMed

Ruiz-Castilla, Mireia; Bosacoma, Pau; Dos Santos, Bruce; Baena, Jacinto; Guilabert, Patricia; Marin-Corral, Judith; Masclans, Joan R; Roca, Oriol; Barret, Juan P

2018-04-10

The IL33/ST2 pathway has been implicated in the pathogenesis of different inflammatory diseases. Our aim was to analyze whether plasma levels of biomarkers involved in the IL33/ST2 axis might help to predict mortality in burn patients. Single-center prospective observational cohort pilot study performed at the Burns Unit of the Plastic and Reconstructive Surgery Department of the Vall d'Hebron University Hospital (Barcelona). All patients aged ≥18 years old with second or third-degree burns requiring admission to the Burns Unit were considered for inclusion. Blood samples were taken to measure levels of interleukins (IL)6, IL8, IL33, and soluble suppression of tumorigenicity-2 (sST2) within 24 h of admission to the Burns Unit and at day 3. Results are expressed as medians and interquartile ranges or as frequencies and percentages. Sixty-nine patients (58 [84.1%] male, mean age 52 [35-63] years, total body surface area burned 21% [13%-30%], Abbreviated Burn Severity Index 6 [4-8]) were included. Thirteen (18.8%) finally died in the Burns Unit. Plasma levels of sST2 measured at day 3 after admission demonstrated the best prediction accuracy for survival (area under the ROC curve 0.85 [0.71-0.99]; P < 0.001). The best cutoff point for the AUROC index was estimated to be 2,561. In the Cox proportional hazards model, after adjusting for potential confounding, a plasma sST2 level ≥2,561 measured at day 3 was significantly associated with mortality (HR 6.94 [1.73-27.74]; P = 0.006). Plasma sST2 at day 3 predicts hospital mortality in burn patients.

Blood transfusions in severe burn patients: Epidemiology and predictive factors.

PubMed

Wu, Guosheng; Zhuang, Mingzhu; Fan, Xiaoming; Hong, Xudong; Wang, Kangan; Wang, He; Chen, Zhengli; Sun, Yu; Xia, Zhaofan

2016-12-01

Blood is a vital resource commonly used in burn patients; however, description of blood transfusions in severe burns is limited. The purpose of this study was to describe the epidemiology of blood transfusions and determine factors associated with increased transfusion quantity. This is a retrospective study of total 133 patients with >40% total body surface area (TBSA) burns admitted to the burn center of Changhai hospital from January 2008 to December 2013. The study characterized blood transfusions in severe burn patients. Univariate and Multivariate regression analyses were used to evaluate the association of clinical variables with blood transfusions. The overall transfusion rate was 97.7% (130 of 133). The median amount of total blood (RBC and plasma), RBC and plasma transfusions was 54 units (Interquartile range (IQR), 20-84), 19 units (IQR, 4-37.8) and 28.5 units (IQR, 14.8-51.8), respectively. The number of RBC transfusion in and outside operation room was 7 (0, 14) and 11 (2, 20) units, and the number of plasma was 6 (0.5, 12) and 21 (11.5, 39.3) units. A median of one unit of blood was transfused per TBSA and an average of 4 units per operation was given in the series. The consumption of plasma is higher than that of RBC. On multivariate regression analysis, age, full-thickness TBSA and number of operations were significant independent predictors associated with the number of RBC transfusion, and coagulopathy and ICU length showed a trend toward RBC consumption. Predictors for increased plasma transfusion were female, high full-thickness TBSA burn and more operations. Severe burn patients received an ample volume of blood transfusions. Fully understanding of predictors of blood transfusions will allow physicians to better optimize burn patients during hospitalization in an effort to use blood appropriately. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Review of the magnetic fusion program by the 1986 ERAB Fusion Panel

NASA Astrophysics Data System (ADS)

Davidson, Ronald C.

1987-09-01

The 1986 ERAB Fusion Panel finds that fusion energy continues to be an attractive energy source with great potential for the future, and that the magnetic fusion program continues to make substantial technical progress. In addition, fusion research advances plasma physics, a sophisticated and useful branch of applied science, as well as technologies important to industry and defense. These factors fully justify the substantial expenditures by the Department of Energy in fusion research and development (R&D). The Panel endorses the overall program direction, strategy, and plans, and recognizes the importance and timeliness of proceeding with a burning plasma experiment, such as the proposed Compact Ignition Tokamak (CIT) experiment.

Plasma NGAL predicts early acute kidney injury no earlier than s-creatinine or cystatin C in severely burned patients.

PubMed

Rakkolainen, Ilmari; Vuola, Jyrki

2016-03-01

Neutrophil gelatinase-associated lipocalin (NGAL) is a novel biomarker used in acute kidney injury (AKI) diagnostics. Studies on burn patients have highlighted it as a promising biomarker for early detection of AKI. This study was designed to discover whether plasma NGAL is as a biomarker superior to serum creatinine and cystatin C in detecting AKI in severely burned patients. Nineteen subjects were enrolled from March 2013 to September 2014 in the Helsinki Burn Centre. Serum creatinine, cystatin C, and plasma NGAL were collected from the patients at admission and every 12h during the first 48h and thereafter daily until seven days following admission. AKI was defined by acute kidney injury network criteria. Nine (47%) developed AKI during their intensive care unit stay and two (11%) underwent renal replacement therapy. All biomarkers were significantly higher in the AKI group but serum creatinine- and cystatin C values reacted more rapidly to changes in kidney function than did plasma NGAL. Plasma NGAL tended to rise on average 72h±29h (95% CI) later in patients with early AKI than did serum creatinine. Area-under-the-curve values calculated for each biomarker were 0.92 for serum creatinine, 0.87 for cystatin C, and 0.62 for plasma NGAL predicting AKI by the receiver-operating-characteristic method. This study demonstrated serum creatinine and cystatin C as faster and more reliable biomarkers than plasma NGAL in detecting early AKI within one week of injury in patients with severe burns. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Nonlinear Burn Control and Operating Point Optimization in ITER

NASA Astrophysics Data System (ADS)

Boyer, Mark; Schuster, Eugenio

2013-10-01

Control of the fusion power through regulation of the plasma density and temperature will be essential for achieving and maintaining desired operating points in fusion reactors and burning plasma experiments like ITER. In this work, a volume averaged model for the evolution of the density of energy, deuterium and tritium fuel ions, alpha-particles, and impurity ions is used to synthesize a multi-input multi-output nonlinear feedback controller for stabilizing and modulating the burn condition. Adaptive control techniques are used to account for uncertainty in model parameters, including particle confinement times and recycling rates. The control approach makes use of the different possible methods for altering the fusion power, including adjusting the temperature through auxiliary heating, modulating the density and isotopic mix through fueling, and altering the impurity density through impurity injection. Furthermore, a model-based optimization scheme is proposed to drive the system as close as possible to desired fusion power and temperature references. Constraints are considered in the optimization scheme to ensure that, for example, density and beta limits are avoided, and that optimal operation is achieved even when actuators reach saturation. Supported by the NSF CAREER award program (ECCS-0645086).

Impaired zinc and copper status in children with burn injuries: need to reassess nutritional requirements.

PubMed

Voruganti, V Saroja; Klein, Gordon L; Lu, Hong-Xing; Thomas, Suchmor; Freeland-Graves, Jeanne H; Herndon, David N

2005-09-01

Major burns are associated with impaired Zn and Cu status. These micronutrients are essential for bone matrix formation, linear growth, and wound healing. This study evaluated the status of Zn and Cu in burned children and assessed adequacy of supplementation. Six children, mean total body surface area (TBSA), 54+/-9% (S.D.), were recruited. Nutrient intakes, plasma, wound exudate, and 24h urine samples were collected and analyzed for Zn and Cu. Bone mineral content was assessed by dual energy X-ray absorptiometry. Dietary Zn and Cu were three times the dietary reference, and mean plasma concentrations of Zn and Cu were low at admission and discharge. Urinary Zn was elevated at admission, whereas Cu was elevated at both times. Wound Zn and Cu concentrations exceeded plasma concentrations, suggesting that inflammatory wound exudate was a primary route of loss. We demonstrate that burn injury in children results in low plasma levels of Zn and Cu that are inadequately compensated during hospitalization.

Determination of deuterium–tritium critical burn-up parameter by four temperature theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nazirzadeh, M.; Ghasemizad, A.; Khanbabei, B.

Conditions for thermonuclear burn-up of an equimolar mixture of deuterium-tritium in non-equilibrium plasma have been investigated by four temperature theory. The photon distribution shape significantly affects the nature of thermonuclear burn. In three temperature model, the photon distribution is Planckian but in four temperature theory the photon distribution has a pure Planck form below a certain cut-off energy and then for photon energy above this cut-off energy makes a transition to Bose-Einstein distribution with a finite chemical potential. The objective was to develop four temperature theory in a plasma to calculate the critical burn up parameter which depends upon initialmore » density, the plasma components initial temperatures, and hot spot size. All the obtained results from four temperature theory model are compared with 3 temperature model. It is shown that the values of critical burn-up parameter calculated by four temperature theory are smaller than those of three temperature model.« less

Experimental Validation Plan for the Xolotl Plasma-Facing Component Simulator Using Tokamak Sample Exposures

NASA Astrophysics Data System (ADS)

Chan, V. S.; Wong, C. P. C.; McLean, A. G.; Luo, G. N.; Wirth, B. D.

2013-10-01

The Xolotl code under development by PSI-SciDAC will enhance predictive modeling capability of plasma-facing materials under burning plasma conditions. The availability and application of experimental data to compare to code-calculated observables are key requirements to validate the breadth and content of physics included in the model and ultimately gain confidence in its results. A dedicated effort has been in progress to collect and organize a) a database of relevant experiments and their publications as previously carried out at sample exposure facilities in US and Asian tokamaks (e.g., DIII-D DiMES, and EAST MAPES), b) diagnostic and surface analysis capabilities available at each device, and c) requirements for future experiments with code validation in mind. The content of this evolving database will serve as a significant resource for the plasma-material interaction (PMI) community. Work supported in part by the US Department of Energy under GA-DE-SC0008698, DE-AC52-07NA27344 and DE-AC05-00OR22725.

Polycapillary lenses for soft x-ray transmission in ITER: Model, comparison with experiments, and potential application

NASA Astrophysics Data System (ADS)

Mazon, D.; Liegeard, C.; Jardin, A.; Barnsley, R.; Walsh, M.; O'Mullane, M.; Sirinelli, A.; Dorchies, F.

2016-11-01

Measuring Soft X-Ray (SXR) radiation [0.1 keV; 15 keV] in tokamaks is a standard way of extracting valuable information on the particle transport and magnetohydrodynamic activity. Generally, the analysis is performed with detectors positioned close to the plasma for a direct line of sight. A burning plasma, like the ITER deuterium-tritium phase, is too harsh an environment to permit the use of such detectors in close vicinity of the machine. We have thus investigated in this article the possibility of using polycapillary lenses in ITER to transport the SXR information several meters away from the plasma in the complex port-plug geometry.

Polycapillary lenses for soft x-ray transmission in ITER: Model, comparison with experiments, and potential application.

PubMed

Mazon, D; Liegeard, C; Jardin, A; Barnsley, R; Walsh, M; O'Mullane, M; Sirinelli, A; Dorchies, F

2016-11-01

Measuring Soft X-Ray (SXR) radiation [0.1 keV; 15 keV] in tokamaks is a standard way of extracting valuable information on the particle transport and magnetohydrodynamic activity. Generally, the analysis is performed with detectors positioned close to the plasma for a direct line of sight. A burning plasma, like the ITER deuterium-tritium phase, is too harsh an environment to permit the use of such detectors in close vicinity of the machine. We have thus investigated in this article the possibility of using polycapillary lenses in ITER to transport the SXR information several meters away from the plasma in the complex port-plug geometry.

Relevance of advanced nuclear fusion research: Breakthroughs and obstructions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coppi, Bruno, E-mail: coppi@mit.edu

2016-03-25

An in depth understanding of the collective modes that can be excited in a wide range of high-energy plasmas is necessary to advance nuclear fusion research in parallel with other fields that include space and astrophysics in particular. Important achievements are shown to have resulted from implementing programs based on this reality, maintaining a tight connection with different areas of investigations. This involves the undertaking of a plurality of experimental approaches aimed at understanding the physics of fusion burning plasmas. At present, the most advanced among these is the Ignitor experiment involving international cooperation, that is designed to investigate burningmore » plasma regimes near ignition for the first time.« less

Advancing the understanding of plasma transport in mid-size stellarators

NASA Astrophysics Data System (ADS)

Hidalgo, Carlos; Talmadge, Joseph; Ramisch, Mirko; TJ-II, the; HXS; TJ-K Teams

2017-01-01

The tokamak and the stellarator are the two main candidate concepts for magnetically confining fusion plasmas. The flexibility of the mid-size stellarator devices together with their unique diagnostic capabilities make them ideally suited to study the relation between magnetic topology, electric fields and transport. This paper addresses advances in the understanding of plasma transport in mid-size stellarators with an emphasis on the physics of flows, transport control, impurity and particle transport and fast particles. The results described here emphasize an improved physics understanding of phenomena in stellarators that complements the empirical approach. Experiments in mid-size stellarators support the development of advanced plasma scenarios in Wendelstein 7-X (W7-X) and, in concert with better physics understanding in tokamaks, may ultimately lead to an advance in the prediction of burning plasma behaviour.

Evidence for Particle Inward Transport, Theoretical prediction and Importance for Reacting Plasmas

NASA Astrophysics Data System (ADS)

Sharky, N.; Coppi, B.; Mazzotta, C.

2017-10-01

The fact that particle transport cannot be described by a diffusion equation but by one that would include an inflow term, involving transport in the direction of the density gradient, was evidenced by experiments on magnetically confined plasmas in which the central plasma density was observed to increase as a result of gas injection at the edge of the plasma column. The validity of the proposed equation has been repeatedly confirmed over the years and limitations for the occurrence of particle inflow in a variety of experimental conditions have been uncovered. The direct experimental observation of the inward propagating particle cloud leading to a profile peaking is described and the effects of different degrees of density peaking in fusion burning plasmas are analyzed. Sponsored in part by the U.S. DoE.

D-3He Spherical Torus Fusion Reactor System Study

DTIC Science & Technology

1992-04-01

assumed as a reasonable range. A.6 Steady-State Particle Balance The steady-state densities of the various species present in a burning plasma are...determined by a detailed particle balance calculation. In addition to the con- sumption and production of various species in a burning plasma , a

Simulation of proton-boron nuclear burning in the potential well of virtual cathode at nanosecond vacuum discharge

NASA Astrophysics Data System (ADS)

Kurilenkov, Yu K.; Tarakanov, V. P.; Gus'kov, S. Yu

2016-11-01

The neutron-free reaction of proton-boron nuclear burning accompanied with the yield of three alpha particles (p + 11B → α + 8Be* → 3α) is of great fundamental and applied interest. However, the implementation of the synthesis of p +11B requires such extreme plasma parameters that are difficult to achieve at well-known schemes of controlled thermonuclear fusion. Earlier, the yield of DD neutrons in a compact nanosecond vacuum discharge (NVD) of low energy with deuterated Pd anode have been observed. Further detailed particle-in-cell simulation by the electrodynamic code have recognized that this experiment represents the realization of rather old scheme of inertial electrostatic confinement (IEC). This IEC scheme is one of the few where the energies of ions needed for p + 11B reaction are quite possible. The purpose of this work on simulation of proton-boron reaction is studying the features of possible p + 11B burning at the IEC scheme based on NVD, thus, to look forward and planning the real experiment.

PNU-282987 improves the hemodynamic parameters by alleviating vasopermeability and tissue edema in dogs subjected to a lethal burns shock.

PubMed

Hu, Quan; Du, Ming-Hua; Hu, Sen; Chai, Jia-ke; Luo, Hong-Min; Hu, Xiao-Han; Zhang, Lin; Lin, Zhi-Long; Ma, Li; Wang, Huan; Sheng, Zhi-Yong

2014-01-01

Excessive inflammation and high vasopermeability can lead to blood volume loss and tissue edema, which can affect the resuscitation and prognosis for serious burn patients. In this experiment, we investigated the effect of PNU-282987, an α7 nicotine cholinergic receptor agonist on the hemodynamic parameters and survival rate by inhibiting vasopermeability and tissue edema during the fluid resuscitation for lethal burn shock. Forty Beagle dogs with intubation of the carotid artery and jugular vein 24 hours before the injury were subjected to 50% TBSA full-thickness burns, and were randomly divided into following four groups: no resuscitation group (group NR), venous fluid resuscitation group (group R), PNU-282987 treatment group (group P), and fluid resuscitation group plus PNU-282987 group (group RP), with 10 dogs in each group. Hemodynamic variables and biochemical parameters were determined with animals in a conscious and cooperative state. The plasma volume and the vasopermeability were determined by indocyanine green and fluorescein isothiocyanate-dextran, respectively. The level of tumor necrosis factor-α and interleukin-1β in plasma, and the water content of different organs were also determined. The mean arterial pressure, cardiac output, and plasma volume of all dogs decreased significantly, and the lung extravascular water index and pulmonary vascular permeability index increased remarkably after burn. The hemodynamic parameters deteriorated continually in group N dogs, and then anuria, hyperlactacidemia, and multiple organ dysfunctions developed. The mean arterial pressure and cardiac output of dogs in group R and group RP returned to preinjury levels at 48 hours postburn. The lung extravascular water index and pulmonary vascular permeability in group R were higher than those before preinjury. The dogs in group RP were found to have a significant increase in plasma volume and urine output, and a remarkable decrease in the levels of tumor necrosis factor-α, interleukin-1α, lactic acid, and organ functions compared with those of group R (P <.05). The survival rate of RP group (100%; 10/10) was significantly higher than that of group N (0; 0/10), group P (20%; 2/10), and group R (60%; 6/10). PNU-282987 combined with intravenous fluid resuscitation significantly improved hemodynamics and the survival rate in the early period after this lethal burn shock. The mechanism may be attributable to the lowering of the level of proinflammatory mediators, amelioration of vasopermeability-induced visceral edema, less of blood volume loss, and protection of vital organs through activation of cholinergic anti-inflammatory pathway.

A general theory for ball lightning structure and light output

NASA Astrophysics Data System (ADS)

Morrow, R.

2018-03-01

A general theory for free-floating ball lightning is presented which unifies the phantom plasma ball theory involving the production of very little light, with theories for ball lightning involving light output produced by burning particles from the soil. The mechanism for the formation of plasma balls is shown to be quite general, producing very similar plasma balls independent of initial ion densities over four orders of magnitude. All that is required is an excess of positive ions in the initial ball of ions. The central plasma density after 1 s is shown to be the reciprocal of the ion neutralization coefficient for all cases, both analytically and computationally. Further, the plasma region has zero electric field in all cases. Surrounding the plasma ball is a sphere of positive ions moving away from the centre via their own space-charge field; this space-charge field, which is the same in all cases near the plasma ball, drives negative ions and negative particles towards the plasma centre. The connection with burning particle theories is the proposition that the burning particles are highly-charged which is very likely after a lightning strike. Burning negatively charged particles would be driven into the plasma ball region and trapped while any positively charged particles would be driven away. The plasma ball structure is shown to last more than 10 s and the ‘burnout time’ for a typical coal particle (as an example) has been measured at 5-10 s this is comparable with the lifetimes observed for ball lightning. The light output from a few hundred particles is estimated to be ~1 W, a typical output for ball lightning. Finally, suggestions are made for the generation of ball lightning in the laboratory.

Cinanserin reduces plasma extravasation after burn plasma transfer in rats.

PubMed

Hernekamp, Jochen-Frederick; Hu, Sissi; Schmidt, Karsten; Walther, Andreas; Kneser, Ulrich; Kremer, Thomas

2013-09-01

Thermal injuries greater than 20% body surface area (BSA) lead to systemic edema and hypovolemic shock. Capillary leakage is induced by different immunomodulative cytokines. Serotonin (5-HT) plays an important role in inflammation, vasodilatation and vasoconstriction and many other pathways such as systemic inflammation in endotoxemia and burns. Cinanserin, a specific 5-HT2 receptor blocking agent was administered to observe whether burn induced systemic edema can be reduced. Donor animals underwent thermal injury (100°C water, 30% BSA, 12s) for positive controls and negative controls underwent a shamburn procedure (37°C water, 30% BSA, 12s). Donor rat-plasma was transferred to healthy individuals after bolus injection of Cinanserin (5mg/kg body weight) was performed in recipient animals. Intravital microscopy was performed in mesenteric venules (0/60/120min) to asses systemic edema by FITC-albumin extravasation. Additionally, leukocyte activation (cells/mm(2)) was observed. Burnplasma-transfer results in systemic capillary leakage that is not observed in sham burn controls. Intraveneous application of Cinanserin significantly reduces systemic burn edema to shamburn levels. Leukocyte-endothelial interactions are significantly reduced by administration of Cinanserin. Specific 5-HT2 antagonism reduces systemic burn edema and leukocyte activation after plasma transfer. Reduction of capillary leakage may be partially mediated by leukocyte dependent as well as independent mechanisms. Future studies need to evaluate specific 5-HT2 receptor subtypes to distinguish between local and systemic effects of serotonin antagonists. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Investigation of key parameters for the development of reliable ITER baseline operation scenarios using CORSICA

NASA Astrophysics Data System (ADS)

Kim, S. H.; Casper, T. A.; Snipes, J. A.

2018-05-01

ITER will demonstrate the feasibility of burning plasma operation by operating DT plasmas in the ELMy H-mode regime with a high ratio of fusion power gain Q ~ 10. 15 MA ITER baseline operation scenario has been studied using CORSICA, focusing on the entry to burn, flat-top burning plasma operation and exit from burn. The burning plasma operation for about 400 s of the current flat-top was achieved in H-mode within the various engineering constraints imposed by the poloidal field coil and power supply systems. The target fusion gain (Q ~ 10) was achievable in the 15 MA ITER baseline operation with a moderate amount of the total auxiliary heating power (~50 MW). It has been observed that the tungsten (W) concentration needs to be maintained low level (n w/n e up to the order of 1.0  ×  10-5) to avoid the radiative collapse and uncontrolled early termination of the discharge. The dynamic evolution of the density can modify the H-mode access unless the applied auxiliary heating power is significantly higher than the H-mode threshold power. Several qualitative sensitivity studies have been performed to provide guidance for further optimizing the plasma operation and performance. Increasing the density profile peaking factor was quite effective in increasing the alpha particle self-heating power and fusion power multiplication factor. Varying the combination of auxiliary heating power has shown that the fusion power multiplication factor can be reduced along with the increase in the total auxiliary heating power. As the 15 MA ITER baseline operation scenario requires full capacity of the coil and power supply systems, the operation window for H-mode access and shape modification was narrow. The updated ITER baseline operation scenarios developed in this work will become a basis for further optimization studies necessary along with the improvement in understanding the burning plasma physics.

Topical local anaesthetics (EMLA) inhibit burn-induced plasma extravasation as measured by digital image colour analysis.

PubMed

Jönsson, A; Mattsson, U; Tarnow, P; Nellgård, P; Cassuto, J

1998-06-01

Amide local anaesthetics have previously been shown to reduce oedema and improve dermal perfusion following experimental burns. Previous studies have used invasive techniques for burn oedema quantification which do not allow continuous monitoring in the same animal. The present study used digital image colour analysis to investigate the effect of topical local anaesthetics on burn-induced extravasation of Evans blue albumin. A standardised full-thickness burn injury (1 x 1 cm) was induced in the abdominal skin of anaesthetised rats. The burn area was subsequently covered with 0.5 g of lidocaine-prilocaine cream 5% (25 mg of each in 1 g; EMLA, ASTRA, Sweden) or placebo cream during the first hour post-burn. One hour after the burn trauma, animals received Evans blue dye intravenously. Skin colour appearances were recorded by macrophotography before the burn and 5, 60. 65, 90, 120, 150, and 180 min post-burn. Colour slides were digitised and colour changes were analysed using the normalised red-green-blue (n-rgb) colour system. Results showed a significant inhibition of Evans blue extravasation between 60 and 180 min post-burn in EMLA-treated animals versus controls. Topical local anaesthetics are potent inhibitors of burn-induced plasma albumin extravasation, probably by direct action on vascular permeability and by inhibition of various steps of the pathophysiological response after burn injury.

Application of reflectometry power flow for magnetic field pitch angle measurements in tokamak plasmas (invited).

PubMed

Gourdain, P-A; Peebles, W A

2008-10-01

Reflectometry has successfully demonstrated measurements of many important parameters in high temperature tokamak fusion plasmas. However, implementing such capabilities in a high-field, large plasma, such as ITER, will be a significant challenge. In ITER, the ratio of plasma size (meters) to the required reflectometry source wavelength (millimeters) is significantly larger than in existing fusion experiments. This suggests that the flow of the launched reflectometer millimeter-wave power can be realistically analyzed using three-dimensional ray tracing techniques. The analytical and numerical studies presented will highlight the fact that the group velocity (or power flow) of the launched microwaves is dependent on the direction of wave propagation relative to the internal magnetic field. It is shown that this dependence strongly modifies power flow near the cutoff layer in a manner that embeds the local magnetic field direction in the "footprint" of the power returned toward the launch antenna. It will be shown that this can potentially be utilized to locally determine the magnetic field pitch angle at the cutoff location. The resultant beam drift and distortion due to magnetic field and relativistic effects also have significant consequences on the design of reflectometry systems for large, high-field fusion experiments. These effects are discussed in the context of the upcoming ITER burning plasma experiment.

Proceedings of the Annual Gaseous Electronics Conference (40th) Held in Atlanta Georgia on 13-16 October 1987

DTIC Science & Technology

1988-07-01

BURNING PLASMA ARC BY A COMBINATION OF HOLOGRAPHIC INTERFEROMETRY AND EMISSION SPECTROSCOPY A. Shah, M. S. Dassanayake and K. Etemadi 5:03 - 5:16 NB...Free- burning Plasma Arc by a Combination of Holo- graphic Interferometry and Emission Spectros- copy, A. SHAH, M. S. DASSANAYAKE,AND K. ETEMA- DI

Polycapillary lenses for soft x-ray transmission in ITER: Model, comparison with experiments, and potential application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mazon, D., E-mail: Didier.Mazon@cea.fr; Jardin, A.; Liegeard, C.

2016-11-15

Measuring Soft X-Ray (SXR) radiation [0.1 keV; 15 keV] in tokamaks is a standard way of extracting valuable information on the particle transport and magnetohydrodynamic activity. Generally, the analysis is performed with detectors positioned close to the plasma for a direct line of sight. A burning plasma, like the ITER deuterium-tritium phase, is too harsh an environment to permit the use of such detectors in close vicinity of the machine. We have thus investigated in this article the possibility of using polycapillary lenses in ITER to transport the SXR information several meters away from the plasma in the complex port-plugmore » geometry.« less

The quiescent H-mode regime for high performance edge localized mode-stable operation in future burning plasmas [The quiescent H-mode regime for high performance ELM-stable operation in future burning plasmas

DOE PAGES

Garofalo, Andrea M.; Burrell, Keith H.; Eldon, David; ...

2015-05-26

For the first time, DIII-D experiments have achieved stationary quiescent H-mode (QH-mode) operation for many energy confinement times at simultaneous ITER-relevant values of beta, confinement, and safety factor, in an ITER similar shape. QH-mode provides excellent energy confinement, even at very low plasma rotation, while operating without edge localized modes (ELMs) and with strong impurity transport via the benign edge harmonic oscillation (EHO). By tailoring the plasma shape to improve the edge stability, the QH-mode operating space has also been extended to densities exceeding 80% of the Greenwald limit, overcoming the long-standing low-density limit of QH-mode operation. In the theory,more » the density range over which the plasma encounters the kink-peeling boundary widens as the plasma cross-section shaping is increased, thus increasing the QH-mode density threshold. Here, the DIII-D results are in excellent agreement with these predictions, and nonlinear MHD analysis of reconstructed QH-mode equilibria shows unstable low n kink-peeling modes growing to a saturated level, consistent with the theoretical picture of the EHO. Furthermore, high density operation in the QH-mode regime has opened a path to a new, previously predicted region of parameter space, named “Super H-mode” because it is characterized by very high pedestals that can be more than a factor of two above the peeling-ballooning stability limit for similar ELMing H-mode discharges at the same density.« less

Energy balance studies and plasma catecholamine values for patients with healed burns.

PubMed

Wallace, B H; Cone, J B; Caldwell, F T

1991-01-01

We report heat balance studies and plasma catecholamine values for 49 children and young adults with healed burn wounds (age range 0.6 to 31 years and burn range 1% to 82% body surface area burned; mean 41%). All measurements were made during the week of discharge. Heat production for patients with healed burns was not significantly different from predicted normal values. However, compartmented heat loss demonstrated a persistent increment in evaporative heat loss that was secondary to continued elevation of cutaneous water vapor loss immediately after wound closure. A reciprocal decrement in dry heat loss was demonstrated (as a result of a cooler average surface temperature, 0.84 degree C cooler than the average integrated skin temperature of five normal volunteers who were studied in our unit under similar environmental conditions). Mean values for plasma catecholamines were in the normal range: epinephrine = 56 +/- 37 pg/ml, norepinephrine = 385 +/- 220 pg/ml, and dopamine = 34 +/- 29 pg/ml. In conclusion, patients with freshly healed burn wounds have normal rates of heat production; however, there is a residual increment in transcutaneous water vapor loss, which produces surface cooling and decreased average surface temperature, which in turn lowers dry heat loss by an approximately equivalent amount.

Properties of the ion-ion hybrid resonator in fusion plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morales, George J.

2015-10-06

The project developed theoretical and numerical descriptions of the properties of ion-ion hybrid Alfvén resonators that are expected to arise in the operation of a fusion reactor. The methodology and theoretical concepts were successfully compared to observations made in basic experiments in the LAPD device at UCLA. An assessment was made of the excitation of resonator modes by energetic alpha particles for burning plasma conditions expected in the ITER device. The broader impacts included the generation of basic insight useful to magnetic fusion and space science researchers, defining new avenues for exploration in basic laboratory experiments, establishing broader contacts betweenmore » experimentalists and theoreticians, completion of a Ph.D. dissertation, and promotion of interest in science through community outreach events and classroom instruction.« less

Optimization of air plasma reconversion of UF6 to UO2 based on thermodynamic calculations

NASA Astrophysics Data System (ADS)

Tundeshev, Nikolay; Karengin, Alexander; Shamanin, Igor

2018-03-01

The possibility of plasma-chemical conversion of depleted uranium-235 hexafluoride (DUHF) in air plasma in the form of gas-air mixtures with hydrogen is considered in the paper. Calculation of burning parameters of gas-air mixtures is carried out and the compositions of mixtures obtained via energy-efficient conversion of DUHF in air plasma are determined. With the help of plasma-chemical conversion, thermodynamic modeling optimal composition of UF6-H2-Air mixtures and its burning parameters, the modes for production of uranium dioxide in the condensed phase are determined. The results of the conducted researches can be used for creation of technology for plasma-chemical conversion of DUHF in the form of air-gas mixtures with hydrogen.

Thalidomide decreases the plasma levels of IL-1 and TNF following burn injury: is it a new drug for modulation of systemic inflammatory response.

PubMed

Eski, Muhitdin; Sahin, Ismail; Sengezer, Mustafa; Serdar, Muhittin; Ifran, Ahmet

2008-02-01

TNF and IL-1, which are produced from phagocytic cells, can produce a significant systemic inflammatory response independently by inducing systemic leukocyte and endothelial cell activation. These cytokines play a pivotal role in development of systemic inflammatory response after severe burn. Thalidomide has been shown to decrease the secretion of TNF from phagocytic cells, therefore suppression of TNF and IL-1 production from activated phagocytic cells might be a successful treatment modality for prevention of systemic inflammatory response following severe burn. To address this issue, we aimed to show whether thalidomide treatment decreased or suppressed plasma levels of TNF and IL-1 following burn in rats. Following the injury, 36 rats were randomly separated into two experimental groups at the third and seventh days. Rats in the experimental group had oral thalidomide (10mg/kg day) treatment for three and seven consecutive days whereas animals in control groups had no treatment. Thalidomide treatment decreased TNF and IL-1 significantly in both experimental groups at both the points (P<0.05). Although in this study we just showed inhibitory effect of thalidomide on plasma the level of TNF and IL-1, we speculate that thalidomide may have modulatory effect on the systemic inflammatory response after burn by decreasing plasma levels of TNF and IL-1.

Pyruvate in oral rehydration salt improves hemodynamics, vasopermeability and survival after burns in dogs.

PubMed

Liu, Rui; Hu, Xiao-Hang; Wang, Shu-Ming; Guo, Si-Jia; Li, Zong-Yu; Bai, Xiao-Dong; Zhou, Fang-Qiang; Hu, Sen

2016-06-01

To investigate whether pyruvate-enriched oral rehydration solution (Pyr-ORS), compared with citrate-enriched ORS (Cit-ORS), improves hemodynamics and organ function by alleviating vasopermeability and plasma volume loss during intra-gastric fluid rehydration in dogs with severe burn. Forty dogs subjected to severe burn were randomly divided into four groups (n=10): two oral rehydrated groups with Pyr-ORS and Cit-ORS (group PR and group CR), respectively, according to the Parkland formula during the first 24h after burns. Other two groups were the intravenous (IV) resuscitation (group VR) with lactated Ringer's solution with the same dosage and no fluid rehydration (group NR). During the next 24h, all groups received the same IV infusion. The hemodynamics, plasma volume, vasopermeability and water contents and function of various organs were determined. Plasma levels of vascular endothelial growth factor (VEGF) and platelet activating factor (PAF) were detected by ELISA. Hemodynamics parameters were significantly improved in group PR superior to group CR after burns. Levels of VEGF and PAF were significantly lower in group PR than in group CR. Organ function parameters were also greatly preserved in group PR, relative to groups CR and NR. Lactic acidosis was fully corrected and survival increased in group PR (50.0%), compared to group CR (20.0%). Pyr-ORS was more effective than Cit-ORS in improving hemodynamics, visceral blood perfusion and organ function by alleviating vasopermeability-induced visceral edema and plasma volume loss in dogs with severe burn. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Valproic acid treatment attenuates caspase-3 activation and improves survival after lethal burn injury in a rodent model.

PubMed

Luo, Hong-Min; Hu, Sen; Bai, Hui-Ying; Wang, Hai-Bin; Du, Ming-Hua; Lin, Zhi-Long; Ma, Li; Wang, Huan; Lv, Yi; Sheng, Zhi-Yong

2014-01-01

Burn injury may result in multiple organ dysfunction partially because of apoptotic cell death. The authors have previously shown that valproic acid (VPA) improves survival in a dog burn model. The aim of this study is to examine whether a VPA improves survival in a rodent burn model and whether this was because of inhibition of cell apoptosis. Rats were subjected to third-degree 55% TBSA burns and randomized to treatment with a VPA (300 mg/kg) or normal saline. One group of animals was monitored for 12 hours for survival analysis; another group was killed at 6 hours after injury, and brains, hearts, and blood samples were harvested for examination. Plasma creatine kinase (CK)-MB activities and neuron-specific enolase (NSE) levels were measured to evaluate the cardiac and brain damages. The effects of a VPA on acetylation of histone H3 and caspase-3 activation were also evaluated. Major burn injury resulted in a significant decrease in the acetylation of histone H3, and there was an increase in plasma CK-MB activities, NSE concentrations, and tissue levels of activated caspase-3. A VPA treatment significantly increased the acetylation of histone H3 and survival of the animals after major burn injury. In addition, a VPA treatment significantly attenuated the plasma CK-MB activities, an NSE concentrations, and inhibited caspase-3 activation after major burn injury. These results indicate that a VPA can attenuate cardiac and brain injury, and can improve survival in a rodent model of lethal burn injury. These protective effects may be mediated in part through the inhibition of caspase-3 activation.

Control of ITBs in Magnetically Confined Burning Plasmas

NASA Astrophysics Data System (ADS)

Panta, S. R.; Newman, D. E.; Terry, P. W.; Sanchez, R.

2017-10-01

In the magnetically confined burning plasma devices (in this case Tokamaks), internal transport barriers (ITBs) are those regimes in which the turbulence is suppressed by the E X B velocity shear, reducing the turbulent transport. This often occurs at a critical gradient in the profiles. The change in the transport then modifies the density and temperature profiles feeding back on the system. These transport barriers have to be controlled both to form them for improved confinement and remove them to both prevent global instabilities and to remove the ash and unnecessary impurities in the device. In this work we focus on pellet injection and modulated RF heating as a way to trigger and control the ITBs. These have an immediate consequence on density and temperature and hence pressure profiles acting as a control knob. For example, depending upon pellet size and its radial position of injection, it either helps to form or strengthen the barrier or to get rid of ITBs in the different transport channels of the burning plasmas. This transport model is then used to investigate the control and dynamics of the transport barriers in burning plasmas using pellets and RF addition to the NBI power and alpha power.

X-ray spectroscopic diagnostics and modeling of polar-drive implosion experiments on the National Ignition Facility

NASA Astrophysics Data System (ADS)

Hakel, P.; Kyrala, G. A.; Bradley, P. A.; Krasheninnikova, N. S.; Murphy, T. J.; Schmitt, M. J.; Tregillis, I. L.; Kanzleieter, R. J.; Batha, S. H.; Fontes, C. J.; Sherrill, M. E.; Kilcrease, D. P.; Regan, S. P.

2014-06-01

A series of experiments featuring laser-imploded plastic-shell targets filled with hydrogen or deuterium were performed on the National Ignition Facility. The shells (some deuterated) were doped in selected locations with Cu, Ga, and Ge, whose spectroscopic signals (indicative of local plasma conditions) were collected with a time-integrated, 1-D imaging, spectrally resolved, and absolute-intensity calibrated instrument. The experimental spectra compare well with radiation hydrodynamics simulations post-processed with a non-local thermal equilibrium atomic kinetics and spectroscopic-quality radiation-transport model. The obtained degree of agreement between the modeling and experimental data supports the application of spectroscopic techniques for the determination of plasma conditions, which can ultimately lead to the validation of theoretical models for thermonuclear burn in the presence of mix. Furthermore, the use of a lower-Z dopant element (e.g., Fe) is suggested for future experiments, since the ˜2 keV electron temperatures reached in mixed regions are not high enough to drive sufficient H-like Ge and Cu line emissions needed for spectroscopic plasma diagnostics.

Inductive flux usage and its optimization in tokamak operation

DOE PAGES

Luce, Timothy C.; Humphreys, David A.; Jackson, Gary L.; ...

2014-07-30

The energy flow from the poloidal field coils of a tokamak to the electromagnetic and kinetic stored energy of the plasma are considered in the context of optimizing the operation of ITER. The goal is to optimize the flux usage in order to allow the longest possible burn in ITER at the desired conditions to meet the physics objectives (500 MW fusion power with energy gain of 10). A mathematical formulation of the energy flow is derived and applied to experiments in the DIII-D tokamak that simulate the ITER design shape and relevant normalized current and pressure. The rate ofmore » rise of the plasma current was varied, and the fastest stable current rise is found to be the optimum for flux usage in DIII-D. A method to project the results to ITER is formulated. The constraints of the ITER poloidal field coil set yield an optimum at ramp rates slower than the maximum stable rate for plasmas similar to the DIII-D plasmas. Finally, experiments in present-day tokamaks for further optimization of the current rise and validation of the projections are suggested.« less

Alfven Eigenmode Control in DIII-D

NASA Astrophysics Data System (ADS)

Hu, W.; Olofsson, E.; Welander, A.; van Zeeland, M.; Collins, C.; Heidbrink, W.

2017-10-01

Alfven eigenmodes (AE) driven by fast ions from neutral beam and ion cyclotron heating are common in present day tokamak plasmas and are expected to be destabilized by alpha particles in future burning plasma experiments. Because these waves have been shown to cause loss and redistribution of fast ions which can impact plasma performance and potentially device integrity, developing control techniques for AEs is of paramount importance. In the DIII-D plasma control system, spectral analysis of real-time ECE data is used as a monitor of AE amplitude, frequency, and location. These values are then used for feedback control of the neutral beam power to control Alfven waves and reduce fast ion loss. This work describes tests of AE control experiments in the current ramp up phase, during which multiple Alfven eigenmodes are typically unstable and fast ion confinement is degraded significantly. Comparisons of neutron emission and confined fast ion profiles with and without active AE control will be made. Work supported by the U.S. Dept. of Energy under Award Number DE-FC02-04ER54698.

Reaction-in-flight neutrons as a test of stopping power in degenerate plasmas

NASA Astrophysics Data System (ADS)

Hayes, A. C.; Jungman, Gerard; Schulz, A. E.; Boswell, M.; Fowler, M. M.; Grim, G.; Klein, A.; Rundberg, R. S.; Wilhelmy, J. B.; Wilson, D.; Cerjan, C.; Schneider, D.; Sepke, S. M.; Tonchev, A.; Yeamans, C.

2015-08-01

We present the first measurements of reaction-in-flight (RIF) neutrons in an inertial confinement fusion system. The experiments were carried out at the National Ignition Facility, using both Low Foot and High Foot drives and cryogenic plastic capsules. In both cases, the high-energy RIF ( En> 15 MeV) component of the neutron spectrum was found to be about 10-4 of the total. The majority of the RIF neutrons were produced in the dense cold fuel surrounding the burning hotspot of the capsule, and the data are consistent with a compressed cold fuel that is moderately to strongly coupled (Γ˜ 0.6) and electron degenerate (θFermi/θe˜ 4). The production of RIF neutrons is controlled by the stopping power in the plasma. Thus, the current RIF measurements provide a unique test of stopping power models in an experimentally unexplored plasma regime. We find that the measured RIF data strongly constrain stopping models in warm dense plasma conditions, and some models are ruled out by our analysis of these experiments.

Reaction-in-flight neutrons as a test of stopping power in degenerate plasmas

DOE PAGES

Hayes, A. C.; Jungman, Gerard; Schulz, A. E.; ...

2015-08-06

We present the first measurements of reaction-in-flight (RIF) neutrons in an inertial confinement fusion system. The experiments were carried out at the National Ignition Facility, using both Low Foot and High Foot drives and cryogenic plastic capsules. In both cases, the high-energy RIF (E n > 15 MeV) component of the neutron spectrum was found to be about 10 –4 of the total. The majority of the RIF neutrons were produced in the dense cold fuel surrounding the burning hotspot of the capsule, and the data are consistent with a compressed cold fuel that is moderately to strongly coupled (Γ~more » 0.6) and electron degenerate (θ Fermi/θ e~ 4). The production of RIF neutrons is controlled by the stopping power in the plasma. Thus, the current RIF measurements provide a unique test of stopping power models in an experimentally unexplored plasma regime. In conclusion, we find that the measured RIF data strongly constrain stopping models in warm dense plasma conditions, and some models are ruled out by our analysis of these experiments.« less

[Advances in the research of zinc deficiency and zinc supplementation treatment in patients with severe burns].

PubMed

Wang, X X; Zhang, M J; Li, X B

2018-01-20

Zinc is one of the essential trace elements in human body, which plays an important role in regulating acute inflammatory response, glucose metabolism, anti-oxidation, immune and gastrointestinal function of patients with severe burns. Patients with severe burns may suffer from zinc deficiency because of insufficient amount of zinc intake from the diet and a large amount of zinc lose through wounds and urine. Zinc deficiency may affect their wound healing process and prognosis. This article reviews the characteristics of zinc metabolism in patients with severe burns through dynamic monitoring the plasma and urinary concentration of zinc. An adequate dosage of zinc supplemented to patients with severe burns by an appropriate method can increase the level of zinc in plasma and skin tissue and improve wound healing, as well as reduce the infection rates and mortality. At the same time, it is important to observe the symptoms and signs of nausea, dizziness, leukopenia and arrhythmia in patients with severe burns after supplementing excessive zinc.

Ulinastatin Suppresses Burn-Induced Lipid Peroxidation and Reduces Fluid Requirements in a Swine Model

PubMed Central

Luo, Hong-Min; Du, Ming-Hua; Lin, Zhi-Long; Hu, Quan; Zhang, Lin; Ma, Li; Wang, Huan; Wen, Yu; Lv, Yi; Lin, Hong-Yuan; Pi, Yu-Li; Hu, Sen; Sheng, Zhi-Yong

2013-01-01

Objective. Lipid peroxidation plays a critical role in burn-induced plasma leakage, and ulinastatin has been reported to reduce lipid peroxidation in various models. This study aims to examine whether ulinastatin reduces fluid requirements through inhibition of lipid peroxidation in a swine burn model. Methods. Forty miniature swine were subjected to 40% TBSA burns and were randomly allocated to the following four groups: immediate lactated Ringer's resuscitation (ILR), immediate LR containing ulinastatin (ILR/ULI), delayed LR resuscitation (DLR), and delayed LR containing ulinastatin (DLR/ULI). Hemodynamic variables, net fluid accumulation, and plasma thiobarbituric acid reactive substances (TBARS) concentrations were measured. Heart, liver, lung, skeletal muscle, and ileum were harvested at 48 hours after burn for evaluation of TBARS concentrations, activities of antioxidant enzymes, and tissue water content. Results. Ulinastatin significantly reduced pulmonary vascular permeability index (PVPI) and extravascular lung water index (ELWI), net fluid accumulation, and water content of heart, lung, and ileum in both immediate or delayed resuscitation groups. Furthermore, ulinastatin infusion significantly reduced plasma and tissue concentrations of TBARS in both immediate or delayed resuscitation groups. Conclusions. These results indicate that ulinastatin can reduce fluid requirements through inhibition of lipid peroxidation. PMID:23738046

Development of high poloidal beta, steady-state scenario with ITER-like tungsten divertor on EAST

NASA Astrophysics Data System (ADS)

Garofalo, A. M.; Gong, X. Z.; Qian, J.; Chen, J.; Li, G.; Li, K.; Li, M. H.; Zhai, X.; Bonoli, P.; Brower, D.; Cao, L.; Cui, L.; Ding, S.; Ding, W. X.; Guo, W.; Holcomb, C.; Huang, J.; Hyatt, A.; Lanctot, M.; Lao, L. L.; Liu, H.; Lyu, B.; McClenaghan, J.; Peysson, Y.; Ren, Q.; Shiraiwa, S.; Solomon, W.; Zang, Q.; Wan, B.

2017-07-01

Recent experiments on EAST have achieved the first long pulse H-mode (61 s) with zero loop voltage and an ITER-like tungsten divertor, and have demonstrated access to broad plasma current profiles by increasing the density in fully-noninductive lower hybrid current-driven discharges. These long pulse discharges reach wall thermal and particle balance, exhibit stationary good confinement (H 98y2 ~ 1.1) with low core electron transport, and are only possible with optimal active cooling of the tungsten armors. In separate experiments, the electron density was systematically varied in order to study its effect on the deposition profile of the external lower hybrid current drive (LHCD), while keeping the plasma in fully-noninductive conditions and with divertor strike points on the tungsten divertor. A broadening of the current profile is found, as indicated by lower values of the internal inductance at higher density. A broad current profile is attractive because, among other reasons, it enables internal transport barriers at large minor radius, leading to improved confinement as shown in companion DIII-D experiments. These experiments strengthen the physics basis for achieving high performance, steady state discharges in future burning plasmas.

Development of high poloidal beta, steady-state scenario with ITER-like tungsten divertor on EAST

DOE PAGES

Garofalo, Andrea M.; Gong, X. Z.; Qian, J.; ...

2017-06-07

Recent experiments on EAST have achieved the first long pulse H-mode (61 s) with zero loop voltage and an ITER-like tungsten divertor, and have demonstrated access to broad plasma current profiles by increasing the density in fully-noninductive lower hybrid current-driven discharges. These long pulse discharges reach wall thermal and particle balance, exhibit stationary good confinement (H 98y2~1.1) with low core electron transport, and are only possible with optimal active cooling of the tungsten armors. In separate experiments, the electron density was systematically varied in order to study its effect on the deposition profile of the external lower hybrid current drivemore » (LHCD), while keeping the plasma in fully-noninductive conditions and with divertor strike points on the tungsten divertor. A broadening of the current profile is found, as indicated by lower values of the internal inductance at higher density. A broad current profile is attractive because, among other reasons, it enables internal transport barriers at large minor radius, leading to improved confinement as shown in companion DIII-D experiments. These experiments strengthen the physics basis for achieving high performance, steady state discharges in future burning plasmas.« less

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

NASA Astrophysics Data System (ADS)

Semenyshyn, R. V.; Veklich, A. N.; Babich, I. L.; Boretskij, V. F.

2014-10-01

Plasma of the free burning electric arc between Ag-SnO2-ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hegna, Chris

The role of this DOE grant was to provide administrative and software support for the U. S. Burning Plasma Organization (USBPO). The USBPO is a grassroots organization of fusion plasma scientists that concentrates broadly on issues of interest in burning plasma physics in general with a particular emphasis on the needs of the ITER program. The particular role of this grant was to provide support of the communication needs of the USBPO primarily through the administration and maintenance of the USBPO server, the public USBPO website, e-mail lists and numerous members-only discussion forums and mail lists.

Electroacupuncture improves burn-induced impairment in gastric motility mediated via the vagal mechanism in rats.

PubMed

Song, J; Yin, J; Sallam, H S; Bai, T; Chen, Y; Chen, J D Z

2013-10-01

Delayed gastric emptying (GE) is common in patients with severe burns. This study was designed to investigate effects and mechanisms of electroacupuncture (EA) on gastric motility in rats with burns. Male rats (intact and vagotomized) were implanted with gastric electrodes, chest and abdominal wall electrodes for investigating the effects of EA at ST-36 (stomach-36 or Zusanli) on GE, gastric slow waves, autonomic functions, and plasma interleukin 6 (IL-6) 6 and 24 h post severe burns. (i) Burn delayed GE (P < 0.001). Electroacupuncture improved GE 6 and 24 h post burn (P < 0.001). Vagotomy blocked the EA effect on GE. (ii) Electroacupuncture improved burn-induced gastric dysrhythmia. The percentage of normal slow waves was increased with EA 6 and 24 h post burn (P = 0.02). (iii) Electroacupuncture increased vagal activity assessed by the spectral analysis of heart rate variability (HRV). The high-frequency component reflecting vagal component was increased with EA 6 (P = 0.004) and 24 h post burn (P = 0.03, vs sham-EA). (iv) Electroacupuncture attenuated burn-induced increase in plasma IL-6 at both 6 (P = 0.03) and 24 h post burn (P = 0.003). Electroacupuncture at ST-36 improves gastric dysrhythmia and accelerates GE in rats with burns. The improvement seems to be mediated via the vagal pathway involving the inflammatory cytokine IL-6. © 2013 John Wiley & Sons Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karlstad, M.D.; DeMichele, S.J.; Istfan, N.

The effects of burn and first-pass splanchnic leucine extraction (FPE) on protein kinetics and energy expenditure were assessed by measuring O/sub 2/ consumption, CO/sub 2/ production, nitrogen balance, leucine kinetics, and tissue fractional protein synthetic rates (FSR-%/day) in enterally fed rats. Anesthetized male rats (200 g) were scalded on their dorsum with boiling water (25-30% body surface area) and enterally fed isovolemic diets that provided 60 kcal/day and 2.4 g of amino acids/day for 3 days. Controls were not burned. An intravenous or intragastric infusion of L-(1-/sup 14/C)leucine was used to assess protein kinetics on day 3. FPE was takenmore » as the ratio of intragastric to intravenous plasma leucine specific activity. There was a 69% reduction in cumulative nitrogen balance (P less than 0.001) and a 17-19% increase in leucine oxidation (P less than 0.05) and total energy expenditure (P less than 0.01) in burned rats. A 15% decrease in plasma leucine clearance (P less than 0.05) was accompanied by a 20% increase in plasma (leucine) (P less than 0.01) in burned rats. Burn decreased rectus muscle FSR from 5.0 +/- 0.4 to 3.5 +/- 0.5 (P less than 0.05) and increased liver FSR from 19.0 +/- 0.5 to 39.2 +/- 3.4 (P less than 0.01). First pass extraction of dietary leucine by the splanchnic bed was 8% in controls and 26% in burned rats. Leucine kinetics corrected for FPE showed increased protein degradation with burn that was not evident without FPE correction. This hypermetabolic burn model can be useful in the design of enteral diets that optimize rates of protein synthesis and degradation.« less

Energetic particle-driven compressional Alfvén eigenmodes and prospects for ion cyclotron emission studies in fusion plasmas

NASA Astrophysics Data System (ADS)

Gorelenkov, N. N.

2016-10-01

As a fundamental plasma oscillation the compressional Alfvén waves (CAWs) are interesting for plasma scientists both academically and in applications for fusion plasmas. They are believed to be responsible for the ion cyclotron emission (ICE) observed in many tokamaks. The theory of CAW and ICE was significantly advanced at the end of 20th century in particular motivated by first DT experiments on TFTR and subsequent JET DT experimental studies. More recently, ICE theory was advanced by ST (or spherical torus) experiments with the detailed theoretical and experimental studies of the properties of each instability signal. There the instability responsible for ICE signals previously indistinguishable in high aspect ratio tokamaks became the subjects of experimental studies. We discuss further the prospects of ICE theory and its applications for future burning plasma experiments such as the ITER tokamak-reactor prototype being build in France where neutrons and gamma rays escaping the plasma create extremely challenging conditions for fusion alpha particle diagnostics. This manuscript has been authored by Princeton University under Contract Number DE-AC02-09CH11466 with the US Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes.

Enhancement of burning velocity by dissociated oxygen atoms

NASA Astrophysics Data System (ADS)

Akashi, Haruaki; Yoshinaga, Tomokazu; Sasaki, Koichi

2015-09-01

Green technology, such as preventing global warming, has been developed for years. Researches on plasma assisted combustion is one of the technologies and have been done for investigating more efficient combustion, more efficient use of fossil fuel with plasmas or applying electric fields. In the ignition time delay analyses with the dissociated oxygen atoms which is generated by non-equilibrium plasma had significant effect on the ignition time. In this paper, dissociated oxygen could effect on burning velocity or not has been examined using CHEMKIN. As a result, no effect can be seen with dissociation degree of lower than 10-3. But there is an effect on the enhancement of burning velocity with higher degree of 10-3. At the dissociation degree of 5×10-2, the burning velocity is enhanced at a factor of 1.24. And it is found that the distributions of each species in front of preheat zone are completely different. The combustion process is proceeded several steps in advance, and generation of H2O, CO and CO2 can be seen before combustion in higher dissociation case. This work was supported by KAKENHI (22340170).

ITER-FEAT operation

NASA Astrophysics Data System (ADS)

Shimomura, Y.; Aymar, R.; Chuyanov, V. A.; Huguet, M.; Matsumoto, H.; Mizoguchi, T.; Murakami, Y.; Polevoi, A. R.; Shimada, M.; ITER Joint Central Team; ITER Home Teams

2001-03-01

ITER is planned to be the first fusion experimental reactor in the world operating for research in physics and engineering. The first ten years of operation will be devoted primarily to physics issues at low neutron fluence and the following ten years of operation to engineering testing at higher fluence. ITER can accommodate various plasma configurations and plasma operation modes, such as inductive high Q modes, long pulse hybrid modes and non-inductive steady state modes, with large ranges of plasma current, density, beta and fusion power, and with various heating and current drive methods. This flexibility will provide an advantage for coping with uncertainties in the physics database, in studying burning plasmas, in introducing advanced features and in optimizing the plasma performance for the different programme objectives. Remote sites will be able to participate in the ITER experiment. This concept will provide an advantage not only in operating ITER for 24 hours a day but also in involving the worldwide fusion community and in promoting scientific competition among the ITER Parties.

[Transfusional requirements for escharectomy in burned children].

PubMed

Julia, Analía R; Basílico, Hugo; Magaldi, Gustavo; Demirdjian, Graciela

2010-02-01

Early excision has considerably improved outcome in extensive burns, but massive resections usually mean copious bleeding that must be conveniently corrected. The purpose of this study was to measure blood component use during escharectomies in children. All pediatric patients with acute burns excised at the Burn Unit of the Hospital Garrahan during one year were included. Volume of blood component used during and immediately after surgery was analyzed and related to percent excised, time post-burn, and the coexistence of infection and autograft at the time of excision. Ninety-four surgeries in 51 children aged 0-14 years with total burned body surface areas of 5-80% who underwent resections of 3-70% were studied. Total blood use (intra + post-operatively) was 2.07 ml/kg/%excised for red blood cells (60% during surgery) and 0.7 ml/kg/% excised for plasma. Only 12% of patients required platelet transfusion. There was no significant requirement variation with the existence of infection, grafting or time post-burn. Approximately 2 ml/kg/% excised of red blood cells (2/3 for surgery) and 1 ml/kg/% excised of plasma are needed for escharectomies in children. The need for platelets must be judged considering the individual patient.

Experimental Constraints on Iron Mobilization into Biomass Burning Aerosols

NASA Astrophysics Data System (ADS)

Sherry, A. M.; Romaniello, S. J.; Herckes, P.; Anbar, A. D.

2017-12-01

Atmospheric deposition of iron (Fe) can limit marine primary productivity and, therefore, carbon dioxide uptake. Recent modeling studies suggest that biomass burning aerosols may contribute a significant amount of soluble Fe to the surface ocean. To address this hypothesis, we collected foliage samples from species representative of several biomes impacted by severe fire events. Existing studies of burn-induced trace element mobilization have often collected both entrained soil particles along with material from burning biomass, making it difficult to determine the actual source of aerosolized trace metals. In order to better constrain the importance of biomass vs. entrained soil as a source of trace metals in burn aerosols, we conducted burn experiments using soil-free foliage representative of a variety of fire-impacted ecosystems. The resulting burn aerosols were collected in two stages (PM > 2.5 μm and PM < 2.5 μm) on cellulose filters using a high-volume air sampler equipped an all-Teflon impactor. Unburned foliage and burn aerosols were analyzed for Fe and other trace metals using inductively coupled plasma mass spectrometry (ICP-MS). Our results show that 0.06-0.86 % of Fe in plant biomass is likely mobilized as atmospheric aerosols during biomass burning events, depending on the type of foliage. We used these results and estimates of annual global wildfire area to estimate the impact of biomass burning aerosols on total atmospheric Fe flux to the ocean. We estimate that biomass-derived Fe likely contributes 3% of the total soluble Fe flux from aerosols. Prior studies, which implicitly included both biomass and soil-derived Fe, concluded that biomass burning contributed as much as 7% of the total marine soluble Fe flux from aerosols. Together, these studies suggest that biomass and fire-entrained soil probably contribute equally to the total fire-derived Fe aerosol flux. Further study of solubility differences between plant- and soil-derived Fe is needed to improve estimates of the soluble Fe contribution from biomass burning to the marine soluble Fe flux.

Extracorporeal Blood Purification in Burns: A Review

DTIC Science & Technology

2014-09-01

Nester T, Heimbach DM, Gibran NS. The beneficial effects of plasma exchange after severe burn injury. J Burn Care Res 2005;30:243 8. [29] Venkataraman R...hemoadsorption on cytokine removal and short term survival in septic rats. Crit Care Med 2008;36:1573 7. [48] Kellum F a, Song M, Venkataraman R

Terminal Maturation of Orthochromatic Erythroblasts Is Impaired in Burn Patients.

PubMed

Hasan, Shirin; Mosier, Michael J; Conrad, Peggie; Szilagyi, Andrea; Gamelli, Richard L; Muthumalaiappan, Kuzhali

2018-02-20

Mechanisms of erythropoietin (Epo)-resistant anemia in burn patients are poorly understood. We have recently found that administering a nonselective beta 1,2-adrenergic blocker propranolol (PR) was effective in reversing myelo-erythroid commitment through MafB regulation and increase megakaryocyte erythrocyte progenitors in burn patients' peripheral blood mononuclear cell (PBMC)-derived ex vivo culture system. Having known that Epo-dependent proliferation of early erythroblasts is intact after burn injury, here we inquired whether or not Epo-independent maturation stage of erythropoiesis is affected by burn injury and the relative role of PR on late-stage erythropoiesis. While majority of erythropoiesis occurs in the bone marrow, maturation into reticulocytes is crucial for their release into sinusoids to occupy the peripheral circulation for which enucleation is vital. peripheral blood mononuclear cells (PBMCs) from burn patients were extended beyond commitment and proliferation stages to late maturation stage in ex vivo culture to understand the role of PR in burn patients. Burn impedes late maturation of orthochromatic erythroblasts into reticulocytes by restricting the enucleation step. Late-stage erythropoiesis is impaired in burn patients irrespective of PR treatment. Further, substituting the microenvironment with control plasma (homologous) in place of autologous plasma rescues the conversion of orthochromatic erythroblasts to reticulocytes. Results show promise in formulating interventions to regulate late-stage erythropoiesis, which can be used in combination with PR to reduce the number of transfusions.

Study of the triton-burnup process in different JET scenarios using neutron monitor based on CVD diamond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemtsev, G., E-mail: g.nemtsev@iterrf.ru; Amosov, V.; Meshchaninov, S.

We present the results of analysis of triton burn-up process using the data from diamond detector. Neutron monitor based on CVD diamond was installed in JET torus hall close to the plasma center. We measure the part of 14 MeV neutrons in scenarios where plasma current varies in a range of 1-3 MA. In this experiment diamond neutron monitor was also able to detect strong gamma bursts produced by runaway electrons arising during the disruptions. We can conclude that CVD diamond detector will contribute to the study of fast particles confinement and help predict the disruption events in future tokamaks.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stutman, D.; Tritz, K.; Finkenthal, M.

New diagnostic and sensor designs are needed for future burning plasma (BP) fusion experiments, having good space and time resolution and capable of prolonged operation in the harsh BP environment. We evaluate the potential of multi-energy x-ray imaging with filtered detector arrays for BP diagnostic and control. Experimental studies show that this simple and robust technique enables measuring with good accuracy, speed, and spatial resolution the T{sub e} profile, impurity content, and MHD activity in a tokamak. Applied to the BP this diagnostic could also serve for non-magnetic sensing of the plasma position, centroid, ELM, and RWM instability. BP compatiblemore » x-ray sensors are proposed using 'optical array' or 'bi-cell' detectors.« less

Fusion policy advisory committee named

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Department of Energy Secretary James Watkins has announced the formation of new Fusion Policy Advisory Committee which will recommend a policy for conducting DOE's fusion energy research program. Issues that will be considered by the committee include the balance of research activities within the programs, the timing of experiments to test the burning of plasma fuel, the International Thermonuclear Experimental Reactor, and the development of laser technologies, DOE said. Watkins said that he would be entirely open to the committee's advice.

Ion kinetic dynamics in strongly-shocked plasmas relevant to ICF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rinderknecht, H. G.; Amendt, P. A.; Rosenberg, M. J.

Implosions of thin-shell capsules produce strongly-shocked (M > 10), low-density (ρ ~1 mg/cc -1), high-temperature (T i ~keV) plasmas, comparable to those produced in the strongly-shocked DT-vapor in inertial confinement fusion (ICF) experiments. A series of thin-glass targets filled with mixtures of deuterium and Helium-3 gas ranging from 7% to 100% deuterium was imploded to investigate the impact of multi-species ion kinetic mechanisms in ICF-relevant plasmas over a wide range of Knudsen numbers (N K ≡ λ ii/R). Anomalous trends in nuclear yields and burn-averaged ion temperatures in implosions with N K > 0.5, which have been interpreted as signaturesmore » of ion species separation and ion thermal decoupling, are found not to be consistent with single-species ion kinetic effects alone. Experimentally inferred Knudsen numbers predict an opposite yield trend to those observed, confirming the dominance of multi-species physics in these experiments. In contrast, implosions with N K ~ 0.01 follow the expected yield trend, suggesting single-species kinetic effects are dominant. In conclusion, the impact of the observed kinetic physics mechanisms on the formation of the hotspot in ICF experiments is discussed.« less

Ion kinetic dynamics in strongly-shocked plasmas relevant to ICF

DOE PAGES

Rinderknecht, H. G.; Amendt, P. A.; Rosenberg, M. J.; ...

2017-04-20

Implosions of thin-shell capsules produce strongly-shocked (M > 10), low-density (ρ ~1 mg/cc -1), high-temperature (T i ~keV) plasmas, comparable to those produced in the strongly-shocked DT-vapor in inertial confinement fusion (ICF) experiments. A series of thin-glass targets filled with mixtures of deuterium and Helium-3 gas ranging from 7% to 100% deuterium was imploded to investigate the impact of multi-species ion kinetic mechanisms in ICF-relevant plasmas over a wide range of Knudsen numbers (N K ≡ λ ii/R). Anomalous trends in nuclear yields and burn-averaged ion temperatures in implosions with N K > 0.5, which have been interpreted as signaturesmore » of ion species separation and ion thermal decoupling, are found not to be consistent with single-species ion kinetic effects alone. Experimentally inferred Knudsen numbers predict an opposite yield trend to those observed, confirming the dominance of multi-species physics in these experiments. In contrast, implosions with N K ~ 0.01 follow the expected yield trend, suggesting single-species kinetic effects are dominant. In conclusion, the impact of the observed kinetic physics mechanisms on the formation of the hotspot in ICF experiments is discussed.« less

Ion cyclotron emission studies: Retrospects and prospects

DOE PAGES

Gorelenkov, N. N.

2016-06-05

Ion cyclotron emission (ICE) studies emerged in part from the papers by A.B. Mikhailovskii published in the 1970s. Among the discussed subjects were electromagnetic compressional Alfv,nic cyclotron instabilities with the linear growth rate similar ~ √(n α/n e) driven by fusion products, -particles which draw a lot of attention to energetic particle physics. The theory of ICE excited by energetic particles was significantly advanced at the end of the 20th century motivated by first DT experiments on TFTR and subsequent JET experimental studies which we highlight. Recently ICE theory was advanced by detailed theoretical and experimental studies on spherical torusmore » (ST) fusion devices where the instability signals previously indistinguishable in high aspect ratio tokamaks due to high toroidal magnetic field became the subjects of experiments. Finally, we discuss prospects of ICE theory applications for future burning plasma (BP) experiments such as those to be conducted in ITER device in France, where neutron and gamma rays escaping the plasma create extremely challenging conditions fusion alpha particle diagnostics.« less

Ion cyclotron emission studies: Retrospects and prospects

NASA Astrophysics Data System (ADS)

Gorelenkov, N. N.

2016-05-01

Ion cyclotron emission (ICE) studies emerged in part from the papers by A.B. Mikhailovskii published in the 1970s. Among the discussed subjects were electromagnetic compressional Alfvénic cyclotron instabilities with the linear growth rate √ {n_α /n_e } driven by fusion products, -particles which draw a lot of attention to energetic particle physics. The theory of ICE excited by energetic particles was significantly advanced at the end of the 20th century motivated by first DT experiments on TFTR and subsequent JET experimental studies which we highlight. More recently ICE theory was advanced by detailed theoretical and experimental studies on spherical torus (ST) fusion devices where the instability signals previously indistinguishable in high aspect ratio tokamaks due to high toroidal magnetic field became the subjects of experiments. We discuss further prospects of ICE theory applications for future burning plasma (BP) experiments such as those to be conducted in ITER device in France, where neutron and gamma rays escaping the plasma create extremely challenging conditions fusion alpha particle diagnostics.

The role of spray-enhanced swirl flow for combustion stabilization in a stratified-charge DISI engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Wei; Sjöberg, Magnus; Reuss, David L.

Implementing spray-guided stratified-charge direct-injection spark-ignited (DISI) engines is inhibited by the occurrence of misfire and partial burns. Engine-performance tests demonstrate that increasing engine speed induces combustion instability, but this deterioration can be prevented by generating swirling flow during the intake stroke. In-cylinder pressure-based heat-release analysis reveals that the appearance of poor-burn cycles is not solely dependent on the variability of early flame-kernel growth. Moreover, cycles can experience burning-rate regression during later combustion stages and may or may not recover before the end of the cycle. Thermodynamic analysis and optical diagnostics are used here to clarify why swirl improves the combustionmore » repeatability from cycle to cycle. The fluid dynamics of swirl/spray interaction was previously demonstrated using high-speed PIV measurements of in-cylinder motored flow. It was found that the sprays of the multi-hole injector redistribute the intake-generated swirl flow momentum, thereby creating a better-centered higher angular-momentum vortex with reduced variability. The engine operation with high swirl was found to have significant improvement in cycle-to-cycle variations of both flow pattern and flow momentum. This paper is an extension of the previous work. Here, PIV measurements and flame imaging are applied to fired operation for studying how the swirl flow affects variability of ignition and subsequent combustion phases. PIV results for fired operation are consistent with the measurements made of motored flow. They demonstrate that the spark-plasma motion is highly correlated with the direction of the gas flow in the vicinity of the spark-plug gap. Without swirl, the plasma is randomly stretched towards either side of the spark plug, causing variability in the ignition of the two spray plumes that are straddling the spark plug. Conversely, swirl flow always convects the spark plasma towards one spray plume, causing a more repeatable ignition. The swirl decreases local RMS velocity, consistent with an observed reduction of early-burn variability. Broadband flame imaging demonstrates that with swirl, the flame consistently propagates in multiple directions to consume fuel–air mixtures within the piston bowl. In contrast, operation without swirl displays higher variability of flame-spread patterns, occasionally causing the appearance of partial-burn cycles.« less

The role of spray-enhanced swirl flow for combustion stabilization in a stratified-charge DISI engine

DOE PAGES

Zeng, Wei; Sjöberg, Magnus; Reuss, David L.; ...

2016-06-01

Implementing spray-guided stratified-charge direct-injection spark-ignited (DISI) engines is inhibited by the occurrence of misfire and partial burns. Engine-performance tests demonstrate that increasing engine speed induces combustion instability, but this deterioration can be prevented by generating swirling flow during the intake stroke. In-cylinder pressure-based heat-release analysis reveals that the appearance of poor-burn cycles is not solely dependent on the variability of early flame-kernel growth. Moreover, cycles can experience burning-rate regression during later combustion stages and may or may not recover before the end of the cycle. Thermodynamic analysis and optical diagnostics are used here to clarify why swirl improves the combustionmore » repeatability from cycle to cycle. The fluid dynamics of swirl/spray interaction was previously demonstrated using high-speed PIV measurements of in-cylinder motored flow. It was found that the sprays of the multi-hole injector redistribute the intake-generated swirl flow momentum, thereby creating a better-centered higher angular-momentum vortex with reduced variability. The engine operation with high swirl was found to have significant improvement in cycle-to-cycle variations of both flow pattern and flow momentum. This paper is an extension of the previous work. Here, PIV measurements and flame imaging are applied to fired operation for studying how the swirl flow affects variability of ignition and subsequent combustion phases. PIV results for fired operation are consistent with the measurements made of motored flow. They demonstrate that the spark-plasma motion is highly correlated with the direction of the gas flow in the vicinity of the spark-plug gap. Without swirl, the plasma is randomly stretched towards either side of the spark plug, causing variability in the ignition of the two spray plumes that are straddling the spark plug. Conversely, swirl flow always convects the spark plasma towards one spray plume, causing a more repeatable ignition. The swirl decreases local RMS velocity, consistent with an observed reduction of early-burn variability. Broadband flame imaging demonstrates that with swirl, the flame consistently propagates in multiple directions to consume fuel–air mixtures within the piston bowl. In contrast, operation without swirl displays higher variability of flame-spread patterns, occasionally causing the appearance of partial-burn cycles.« less

Clinical and protein metabolic efficacy of glutamine granules-supplemented enteral nutrition in severely burned patients.

PubMed

Peng, Xi; Yan, Hong; You, Zhongyi; Wang, Pei; Wang, Shiliang

2005-05-01

As an abundant amino acid in the human body, glutamine has many important metabolic roles that may protect or promote tissue integrity and enhance the immune system. A relative deficiency of glutamine in such patients could compromise recovery and result in prolonged illness and an increase in late mortality. The purpose of this clinical study is to observe the effects of enteral supplement with glutamine granules on protein metabolism in severely burned patients. Forty-eight severe burn patients (total burn surface area 30-75%, full thickness burn area 20-58%) who met the requirements of the protocol joined this double-blind randomized controlled clinical trial. Patients were randomly divided into two groups: burn control group (B group, 23 patients) and glutamine treated group (Gln group, 25 patients). There was isonitrogenous and isocaloric intake in both groups, glutamine and B group patents were supplemented with glutamine granules or placebo (glycine) at 0.5 g/kg per day for 14 days with oral feeding or tube feeding, respectively. The level of plasma glutamine, plasma protein content, urine nitrogen and urine 3-methylhistidine (3-MTH) excretion were determined, wound healing rate of the burned area and hospital stay were recorded. The results showed that there were significant reductions in plasma glutamine level and abnormal protein metabolism. After supplement with glutamine granules for 14 days, the plasma glutamine concentration was significantly higher than that in B group (607.86+/-147.25 micromol/L versus 447.63+/-132.38 micromol/L, P<0.01) and the plasma prealbumin and transferrin in Gln group were remarkably higher than those in B group (P<0.01), but the concentration of total protein and albumin were not significantly changed compared with B group (P>0.05). On the other hand, the amount of urine nitrogen and 3-MTH excreted in Gln group were significantly lower than that in B group. In addition, wound healing was faster and hospital stay days were shorter in Gln group than B group (46.59+/-12.98 days versus 55.68+/-17.36 days, P<0.05). These indicated that supplement glutamine granules with oral feeding or tube feeding could abate the degree of glutamine depletion, promote protein synthesis, inhibit protein decompose, improve wound healing and reduce hospital stay.

Time-dependent morphological and biochemical changes following cutaneous thermal burn injury and their modulation by copper nicotinate complex: an animal model.

PubMed

Nassar, Muammar A Y; Eldien, Heba M Saad; Tawab, Hanem S Abdel; Saleem, Tahia H; Omar, Hossam M; Nassar, Ahmed Y; Hussein, Mahmoud Rezk Abdelwahed

2012-10-01

Thermal tissue injury is partly mediated by reactive oxygen metabolites. Oxygen free radicals are contributory to local tissue damage following thermal injury and accordingly an interventional therapy using antioxidants may be beneficial. Copper nicotinate complex can scavenge reactive oxygen species (i.e., has antioxidant activity). To examine time-related morphological and biochemical changes following skin thermal injury and their modulation by copper nicotinate complex. An animal model composed of 80 albino rats was established. Ten rats (nonburn group) served as a control group. Seventy rats (burn group) were anesthetized, given a 10% total body surface area, full-thickness burn. Ten rats (from the postburn group) were sacrificed after 24 h (without treatment, i.e., untreated-burn group). The remaining rats were divided into three subgroups (20 rats, each) and were treated topically either with soft paraffin, moist exposed burn ointment (MEBO, a standard therapeutic treatment for burns), or copper nicotinate complex. Five animals from each subgroup were sacrificed every week over a period of 4 weeks. The morphological and biochemical changes were evaluated and compared among the different groups. High levels of the plasma and skin nitiric oxide (marker of oxidative stress) were observed in the untreated-burn group. These levels were significantly low following the application of copper nicotinate complex. Low levels of plasma and skin superoxide dismutase (marker of oxidative stress) and plasma ceruloplasmin were observed in the untreated-burn group. These levels were significantly high following copper nicotinate complex treatment. The total and differential leukocyte counts were low following the onset of the thermal injury. They gradually returned to normal levels over a 4-week period following the application of MEBO or copper nicotinate complex. Compared to untreated-burn group, postburn-healing changes (resolution of the inflammatory reaction, reepithelization of the epidermis, angiogenesis, deposition of collagen fibers, and recovery of the subcellualr organelles) were significantly accelerated following the application of either MEBO or copper nicotinate complex. Application of copper nicotinate complex was associated with improved healing of the thermal burns of the skin. The underlying molecular changes underlying these effects await further investigations.

Discovery of stationary operation of quiescent H-mode plasmas with net-zero neutral beam injection torque and high energy confinement on DIII-D [Discovery of stationary operation of quiescent H-mode plasmas with Net-Zero NBI torque and high energy confinement on DIII-D

DOE PAGES

Burrell, Keith H.; Barada, Kshitish; Chen, Xi; ...

2016-03-11

Here, recent experiments in DIII-D have led to the discovery of a means of modifying edge turbulence to achieve stationary, high confinement operation without Edge Localized Mode (ELM) instabilities and with no net external torque input. Eliminating the ELM-induced heat bursts and controlling plasma stability at low rotation represent two of the great challenges for fusion energy. By exploiting edge turbulence in a novel manner, we achieved excellent tokamak performance, well above the H 98y2 international tokamak energy confinement scaling (H 98y2=1.25), thus meeting an additional confinement challenge that is usually difficult at low torque. The new regime is triggeredmore » in double null plasmas by ramping the injected torque to zero and then maintaining it there. This lowers ExB rotation shear in the plasma edge, allowing low-k, broadband, electromagnetic turbulence to increase. In the H-mode edge, a narrow transport barrier usually grows until MHD instability (a peeling ballooning mode) leads to the ELM heat burst. However, the increased turbulence reduces the pressure gradient, allowing the development of a broader and thus higher transport barrier. A 60% increase in pedestal pressure and 40% increase in energy confinement result. An increase in the ExB shearing rate inside of the edge pedestal is a key factor in the confinement increase. Strong double-null plasma shaping raises the threshold for the ELM instability, allowing the plasma to reach a transport-limited state near but below the explosive ELM stability boundary. The resulting plasmas have burning-plasma-relevant β N=1.6-1.8 and run without the need for extra torque from 3D magnetic fields. To date, stationary conditions have been produced for 2 s or 12 energy confinement times, limited only by external hardware constraints. Stationary operation with improved pedestal conditions is highly significant for future burning plasma devices, since operation without ELMs at low rotation and good confinement is key for fusion energy production.« less

Discovery of stationary operation of quiescent H-mode plasmas with net-zero neutral beam injection torque and high energy confinement on DIII-D [Discovery of stationary operation of quiescent H-mode plasmas with Net-Zero NBI torque and high energy confinement on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burrell, Keith H.; Barada, Kshitish; Chen, Xi

Here, recent experiments in DIII-D have led to the discovery of a means of modifying edge turbulence to achieve stationary, high confinement operation without Edge Localized Mode (ELM) instabilities and with no net external torque input. Eliminating the ELM-induced heat bursts and controlling plasma stability at low rotation represent two of the great challenges for fusion energy. By exploiting edge turbulence in a novel manner, we achieved excellent tokamak performance, well above the H 98y2 international tokamak energy confinement scaling (H 98y2=1.25), thus meeting an additional confinement challenge that is usually difficult at low torque. The new regime is triggeredmore » in double null plasmas by ramping the injected torque to zero and then maintaining it there. This lowers ExB rotation shear in the plasma edge, allowing low-k, broadband, electromagnetic turbulence to increase. In the H-mode edge, a narrow transport barrier usually grows until MHD instability (a peeling ballooning mode) leads to the ELM heat burst. However, the increased turbulence reduces the pressure gradient, allowing the development of a broader and thus higher transport barrier. A 60% increase in pedestal pressure and 40% increase in energy confinement result. An increase in the ExB shearing rate inside of the edge pedestal is a key factor in the confinement increase. Strong double-null plasma shaping raises the threshold for the ELM instability, allowing the plasma to reach a transport-limited state near but below the explosive ELM stability boundary. The resulting plasmas have burning-plasma-relevant β N=1.6-1.8 and run without the need for extra torque from 3D magnetic fields. To date, stationary conditions have been produced for 2 s or 12 energy confinement times, limited only by external hardware constraints. Stationary operation with improved pedestal conditions is highly significant for future burning plasma devices, since operation without ELMs at low rotation and good confinement is key for fusion energy production.« less

The investigation of an electric arc in the long cylindrical channel of the powerful high-voltage AC plasma torch

NASA Astrophysics Data System (ADS)

Rutberg, Ph G.; Popov, S. D.; Surov, A. V.; Serba, E. O.; Nakonechny, Gh V.; Spodobin, V. A.; Pavlov, A. V.; Surov, A. V.

2012-12-01

The comparison of conductivity obtained in experiments with calculated values is made in this paper. Powerful stationary plasma torches with prolonged period of continuous work are popular for modern plasmachemical applications. The maximum electrode lifetime with the minimum erosion can be reached while working on rather low currents. Meanwhile it is required to provide voltage arc drop for the high power achievement. Electric field strength in the arc column of the high-voltage plasma torch, using air as a plasma-forming gas, does not exceed 15 V/cm. It is possible to obtain the high voltage drop in the long arc stabilized in the channel by the intensive gas flow under given conditions. Models of high voltage plasma torches with rod electrodes with power up to 50 kW have been developed and investigated. The plasma torch arcs are burning in cylindrical channels. Present investigations are directed at studying the possibility of developing long arc plasma torches with higher power. The advantage of AC power supplies usage is the possibility of the loss minimization due to the reactive power compensation. The theoretical maximum of voltage arc drop for power supplies with inductive current limitations is about 50 % of the no-load voltage for a single-phase circuit and about 30 % for the three-phase circuit. Burning of intensively blown arcs in the long cylindrical channel using the AC power supply with 10 kV no-load voltage is experimentally investigated in the work. Voltage drops close to the maximum possible had been reached in the examined arcs in single-phase and three-phase modes. Operating parameters for single-phase mode were: current -30 A, voltage drop -5 kV, air flow rate 35 g/s; for three-phase mode: current (40-85) A, voltage drop (2.5-3.2) kV, air flow rate (60-100) g/s. Arc length in the installations exceeded 2 m.

Identification of Neopterin as a Potential Indicator of Infection in Burned Patients,

DTIC Science & Technology

1992-01-01

Patients (43361) DAVID G. BURLESON,’ AVERY JOHNSON, MARVIN SALIN, ARTHUR D. MASON, JR., AND BASIL A. PRUITT, JR. U.S. Army Institute of Surgical...precipitated whole blood or plasma from burned patients . Perchloric acid supematants of sera from infected, but not uninfected, burned rats contained a...fluorescent substance with maximum emission at 420 nm at 355-nm excitation (355 ex/420 em). In this study Mm of serum from burned human patients , several

Plasma L-5-oxoproline kinetics and whole blood glutathione synthesis rates in severely burned adult humans.

PubMed

Yu, Yong-Ming; Ryan, Colleen M; Fei, Zhe-Wei; Lu, Xiao-Ming; Castillo, Leticia; Schultz, John T; Tompkins, Ronald G; Young, Vernon R

2002-02-01

Compromised glutathione homeostasis is associated with increased morbidity in various disease states. We evaluated the kinetics of L-5-oxoproline, an intermediate in the gamma-glutamyl cycle of glutathione production, in fourteen severely burned adults by use of a primed, constant intravenous infusion of L-5-[1-(13)C]oxoproline. In nine of these patients, whole blood glutathione synthesis and plasma kinetics of glycine and leucine were also measured with [(15)N]glycine and L-[(2)H(3)]leucine tracers. Patients were studied under a "basal" condition that provided a low dose of glucose and total parenteral nutrition. For comparison with control subjects, whole blood glutathione synthesis was estimated in six healthy adults. Burn patients in a basal condition showed significantly higher rates of plasma oxoproline clearance and urinary D- and L-oxoproline excretion compared with fasting healthy control subjects. Whole blood glutathione concentration and absolute synthesis rate in the basal state were lower than for control subjects. Total parenteral feeding without cysteine but with generous methionine did not affect oxoproline kinetics or whole blood glutathione synthesis. The estimated rate of glycine de novo synthesis was also lower in burn patients, suggesting a possible change in glycine availability for glutathione synthesis. The roles of precursor amino acid availability, as well as alterations in metabolic capacity, in modulating whole blood glutathione production in burns now require investigation.

Response measurement of single-crystal chemical vapor deposition diamond radiation detector for intense X-rays aiming at neutron bang-time and neutron burn-history measurement on an inertial confinement fusion with fast ignition.

PubMed

Shimaoka, T; Kaneko, J H; Arikawa, Y; Isobe, M; Sato, Y; Tsubota, M; Nagai, T; Kojima, S; Abe, Y; Sakata, S; Fujioka, S; Nakai, M; Shiraga, H; Azechi, H; Chayahara, A; Umezawa, H; Shikata, S

2015-05-01

A neutron bang time and burn history monitor in inertial confinement fusion with fast ignition are necessary for plasma diagnostics. In the FIREX project, however, no detector attained those capabilities because high-intensity X-rays accompanied fast electrons used for plasma heating. To solve this problem, single-crystal CVD diamond was grown and fabricated into a radiation detector. The detector, which had excellent charge transportation property, was tested to obtain a response function for intense X-rays. The applicability for neutron bang time and burn history monitor was verified experimentally. Charge collection efficiency of 99.5% ± 0.8% and 97.1% ± 1.4% for holes and electrons were obtained using 5.486 MeV alpha particles. The drift velocity at electric field which saturates charge collection efficiency was 1.1 ± 0.4 × 10(7) cm/s and 1.0 ± 0.3 × 10(7) cm/s for holes and electrons. Fast response of several ns pulse width for intense X-ray was obtained at the GEKKO XII experiment, which is sufficiently fast for ToF measurements to obtain a neutron signal separately from X-rays. Based on these results, we confirmed that the single-crystal CVD diamond detector obtained neutron signal with good S/N under ion temperature 0.5-1 keV and neutron yield of more than 10(9) neutrons/shot.

Effects of enteral supplementation with glutamine granules on intestinal mucosal barrier function in severe burned patients.

PubMed

Peng, Xi; Yan, Hong; You, Zhongyi; Wang, Pei; Wang, Shiliang

2004-03-01

Glutamine is an important energy source in intestinal mucosa, the small intestine is the major organ of glutamine uptake and metabolism and plays an important role in the maintenance of whole body glutamine homeostasis. The purpose of this clinical study is to observe the protection effects of enteral supplement with glutamine granules on intestinal mucosal barrier function in severe burned patients. Forty-eight severe burn patients (total burn surface area 30-75%, full thickness burn area 20-85%) were randomly divided into two groups: burn control group (B group, 23 patients) and glutamine treated group (Gln group, 25 patients). Glutamine granules 0.5 g/kg were supplied orally for 14 days in Gln group, and the same dosage of placebo were given for 14 days in B group. The plasma level of glutamine, endotoxin and the activity of diamine oxidase (DAO), as well as intestinal mucosal permeability were determined. The results showed that the levels of plasma endotoxin, activity and urinary lactulose and mannitol (L/M) ratio in all patients were significant higher than that of normal control. After taking glutamine granules for 14 days, plasma glutamine concentration was significantly higher in Gln group than that in B group (607.86+/-147.25 microM/l versus 447.63 +/- 132.28 microM/l, P < 0.01). On the other hand, the levels of plasma DAO activity and urinary L/M ratio in Gln group were lower than those in B group. In addition, the wound healing was better and hospital stay days were reduced in the Gln group (46.59 +/- 12.98 days versus 55.68 +/- 17.36 days, P < 0.05). These results indicated that glutamine granules taken orally could abate the degree of intestine injury, lessen intestinal mucosal permeability, ameliorate wound healing and reduce hospital stay.

Scaling Study of Reconnection Heating in Torus Plasma Merging Experiments

NASA Astrophysics Data System (ADS)

Ono, Yasushi; Akimitsu, Moe; Sawada, Asuka; Cao, Qinghong; Koike, Hideya; Hatano, Hironori; Kaneda, Taishi; Tanabe, Hiroshi

2017-10-01

We have been investigating toroidal plasma merging and reconnection for high-power heating of spherical tokamak (ST) and field-reversed configuration (FRC), using TS-3 (ST, FRC: R =0.2m, 1985-), TS-4 (ST, FRC: R =0.5m, 2000-), UTST (ST: R =0.45m, 2008-) and MAST (ST: R =0.9m, 2000-) devices. The series of merging experiments made clear the promising scaling and characteristics of reconnection heating: (i) its ion heating energy that scales with square of the reconnecting magnetic field Brec, (ii) its energy loss lower than 10%, (iii) its ion heating energy (in the downstream) 10 time larger than its electron heating energy (at around X-point) and (iv) low dependence of ion heating on the guide (toroidal) field Bg. The Brec2-scalingwas obtained when the current sheet was compressed to the order of ion gyrodadius. When the sheet was insufficiently compressed, the measured ion temperature was lower than the scaling prediction. Based on this scaling, we realized significant ion heating up to 1.2keV in MAST after 2D elucidation of ion heating up to 250eV in TS-3 [3,4]. This promising scaling leads us to new high Brec reconnection heating experiments for future direct access to burning plasma: TS-U (2017-) in Univ. Tokyo and ST-40 in Tokamak Energy Inc. (2017-). This presentation reviews major progresses in those toroidal plasma merging experiments for physics and fusion applications of magnetic reconnection.

Validation of TGLF in C-Mod and DIII-D using machine learning and integrated modeling tools

NASA Astrophysics Data System (ADS)

Rodriguez-Fernandez, P.; White, Ae; Cao, Nm; Creely, Aj; Greenwald, Mj; Grierson, Ba; Howard, Nt; Meneghini, O.; Petty, Cc; Rice, Je; Sciortino, F.; Yuan, X.

2017-10-01

Predictive models for steady-state and perturbative transport are necessary to support burning plasma operations. A combination of machine learning algorithms and integrated modeling tools is used to validate TGLF in C-Mod and DIII-D. First, a new code suite, VITALS, is used to compare SAT1 and SAT0 models in C-Mod. VITALS exploits machine learning and optimization algorithms for the validation of transport codes. Unlike SAT0, the SAT1 saturation rule contains a model to capture cross-scale turbulence coupling. Results show that SAT1 agrees better with experiments, further confirming that multi-scale effects are needed to model heat transport in C-Mod L-modes. VITALS will next be used to analyze past data from DIII-D: L-mode ``Shortfall'' plasma and ECH swing experiments. A second code suite, PRIMA, allows for integrated modeling of the plasma response to Laser Blow-Off cold pulses. Preliminary results show that SAT1 qualitatively reproduces the propagation of cold pulses after LBO injections and SAT0 does not, indicating that cross-scale coupling effects play a role in the plasma response. PRIMA will be used to ``predict-first'' cold pulse experiments using the new LBO system at DIII-D, and analyze existing ECH heat pulse data. Work supported by DE-FC02-99ER54512, DE-FC02-04ER54698.

Falsely raised whole blood chloride caused by systemic absorption of cerium nitrate cream for burns.

PubMed

Ha, Leah Y; Woollard, Gerald A; Chiu, Weldon W

2015-03-01

Whole blood, serum or plasma chloride is almost exclusively measured by potentiometry with an ion-selective chloride electrode which utilizes membrane selectivity to chloride ions. Other anions such as bromide, iodide and thiosulphate can interfere but usually are not present in high enough concentration to cause significant cross reactivity. A patient from our burns unit had serial chloride measurements on a Radiometer ABL800 blood gas analyser. The results were higher in contrast to plasma measurements on the Abbott Architect Ci8200, which were within reference intervals and in line with the patient's pathophysiological status. This indicated a likely interference with the blood gas analyser chloride estimation. The chloride results on the ABL800 for 3rd, 4th and 5th day after the burn accident were 170, 137 and 119 mmol/L. Corresponding plasma chloride results on the Ci8200 were all around 105 mmol/L. Nitrate was found to be markedly elevated in these samples, and the results were 6.7, 4.9 and 1.1 mmol/L, respectively (reference limit < 0.08 mmol/L). To further demonstrate nitrate was the causative agent, pooled plasma spiked with 7 mmol/L of sodium nitrate caused a rise in the ABL800 chloride from 105 to 202 mmol/L. Later we confirmed that the patient was topically medicated with cerium nitrate cream (Flammacerium®, Sinclair IS Pharma, UK) for his burns. In summary, the results clearly indicated nitrate was the interferent with the ABL800 chloride estimation and the source was the topical burns cerium nitrate cream. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Matrix metalloproteinase-2 and its correlation with basal membrane components laminin-5 and collagen type IV in paediatric burn patients measured with Surface Plasmon Resonance Imaging (SPRI) biosensors.

PubMed

Weremijewicz, Artur; Matuszczak, Ewa; Sankiewicz, Anna; Tylicka, Marzena; Komarowska, Marta; Tokarzewicz, Anna; Debek, Wojciech; Gorodkiewicz, Ewa; Hermanowicz, Adam

2018-06-01

The purpose of this study was the determination of matrix metalloproteinase-2 and its correlation with basal membrane components laminin-5 and collagen type IV in the blood plasma of burn patients measured with Surface Plasmon Resonance Imaging (SPRI) biosensors. 31 children scalded by hot water who were managed at the Department of Paediatric Surgery between 2014-2015, after primarily presenting with burns in 4-20% TBSA were included into the study (age 9 months up to 14 years, mean age 2,5+1 years). There were 10 girls and 21 boys. Venous blood samples were drawn 2-6h, and 12-16h after the thermal injury, and on the subsequent days 3, 5 and 7. The matrix metalloproteinase-2, collagen type IV and laminin-5 concentrations were assessed using Surface Plasmon Resonance Imaging by the investigators blinded to the other data. The MMP-2, laminin-5 and collagen type IV concentrations in the blood plasma of patients with burns, were highest 12-16h after thermal injury, the difference was statistically significant. The MMP-2, laminin-5 and collagen type IV concentrations measured 3 days, 5 days and 7 days after the thermal injury, slowly decreased over time, and on the 7th day reached the normal range, when compared with the concentration measured in controls. Current work is the first follow-up study regarding MMP-2 in burns. MMP-2, laminin-5 and collagen type IV levels were elevated early after burn injury in the plasma of studied patients, and were highest 12-16h after the injury. MMP-2, laminin-5 and collagen type IV levels were not proportional to the severity of the burn. We believe in the possibility that the gradual decrease of MMP-2, collagen type IV and laminin-5 concentrations could be connected with the process of healing, but to prove it, more investigation is needed in this area. The SPR imaging biosensor is a good diagnostic tool for determination of MMP-2, laminin-5 and collagen type IV in blood plasma of patients with burns. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Critical threshold behavior for steady-state internal transport barriers in burning plasmas.

PubMed

García, J; Giruzzi, G; Artaud, J F; Basiuk, V; Decker, J; Imbeaux, F; Peysson, Y; Schneider, M

2008-06-27

Burning tokamak plasmas with internal transport barriers are investigated by means of integrated modeling simulations. The barrier sustainment in steady state, differently from the barrier formation process, is found to be characterized by a critical behavior, and the critical number of the phase transition is determined. Beyond a power threshold, alignment of self-generated and noninductively driven currents occurs and steady state becomes possible. This concept is applied to simulate a steady-state scenario within the specifications of the International Thermonuclear Experimental Reactor.

A. Sakharov and Fusion Research

NASA Astrophysics Data System (ADS)

Coppi, Bruno

2012-02-01

In the landmark paper by Tamm and Sakharov [1], a controlled nuclear fusion reactor based on an axisymmetric magnetic confinement configuration whose principles remain valid to this day, was proposed. In the light of present understanding of plasma physics the virtues (e.g. that of considering the D-D reaction) and the shortcomings of this paper are pointed out. In fact, relatively recent results of theoretical plasma physics (e.g. discovery of the so called second stability region) and advances in high field magnet technology have made it possible to identify the parameters of meaningful experiments capable of exploring D-D and D-^3He burn conditions. At the same time an experimental program (IGNIR) has been undertaken through a (funded) collaboration between Italy and Russia to investigate D-T plasmas close to ignition conditions based on an advanced high field toroidal confinement configuration. A. Sakharov envisioned a bolder approach to fusion research than that advocated by some of his contemporaries. The time taken to design and decide to fabricate the first experiment capable of reaching ignition conditions is due in part to the problem of gaining an adequate understanding the expected physics of fusion burning plasmas. However, most of the relevant financial effort has gone in the pursuit of slow and indirect enterprises complying with the ``playing it safe'' tendencies of large organizations or motivated by the purpose to develop technologies or maintain a high level of expertise in plasma physics to the expected benefit of other kinds of endeavors. The creativity demonstrated by A. Sakharov in dealing with civil rights and disarmament issues is needed, while maintaining our concerns for energy and the environment on a global scale, to orient the funding for fusion research toward a direct and well based scientific effort on concepts for which a variety of developments can be envisioned. These can span from uncovering new physics relevant, for instance, to high energy astrophysics to the feasibility of new neutron sources.[4pt] [1] A. Sakharov, Collected Scientific Works (Publ. Marcel Dekkes, Inc., New York, N.Y., 1982).

Overview of LDX Results

NASA Astrophysics Data System (ADS)

Kesner, J.; Boxer, A. C.; Ellsworth, J. L.; Karim, I.; Garnier, D. T.; Hansen, A. K.; Mauel, M. E.; Ortiz, E. E.

2006-10-01

The levitated dipole experiment (LDX) is a new research facility that is investigating plasma confinement and stability in a dipole magnetic field configuration as a possible catalyzed DD fusion power source that would avoid the burning of tritium. We report the production of high beta plasma confined by a laboratory superconducting dipole using neutral gas fueling and electron cyclotron resonance heating (ECRH). The pressure results from a population of anisotropic energetic trapped electrons that is sustained by microwave heating provided sufficient neutral gas is supplied to the plasma. The trapped electron beta was observed to be limited by the hot electron interchange (HEI) instability, but when the neutral gas was programmed so as to maintain the deuterium gas pressure near 0.2 mPa, the fast electron pressure increased by more than a factor of ten and the resulting stable high beta plasma was maintained quasi-continuously for up to 14 seconds. Low frequency (<10 kHz) fluctuations are sometimes observed at low neutral base pressure.

High-fidelity plasma codes for burn physics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooley, James; Graziani, Frank; Marinak, Marty

Accurate predictions of equation of state (EOS), ionic and electronic transport properties are of critical importance for high-energy-density plasma science. Transport coefficients inform radiation-hydrodynamic codes and impact diagnostic interpretation, which in turn impacts our understanding of the development of instabilities, the overall energy balance of burning plasmas, and the efficacy of self-heating from charged-particle stopping. Important processes include thermal and electrical conduction, electron-ion coupling, inter-diffusion, ion viscosity, and charged particle stopping. However, uncertainties in these coefficients are not well established. Fundamental plasma science codes, also called high-fidelity plasma codes, are a relatively recent computational tool that augments both experimental datamore » and theoretical foundations of transport coefficients. This paper addresses the current status of HFPC codes and their future development, and the potential impact they play in improving the predictive capability of the multi-physics hydrodynamic codes used in HED design.« less

Direct depth distribution measurement of deuterium in bulk tungsten exposed to high-flux plasma

DOE PAGES

Taylor, Chase N.; Shimada, M.

2017-05-08

Understanding tritium retention and permeation in plasma-facing components is critical for fusion safety and fuel cycle control. Glow discharge optical emission spectroscopy (GD-OES) is shown to be an effective tool to reveal the depth profile of deuterium in tungsten. Results confirm the detection of deuterium. Furthermore, a ~46 µm depth profile revealed that the deuterium content decreased precipitously in the first 7 µm, and detectable amounts were observed to depths in excess of 20 µm. The large probing depth of GD-OES (up to 100s of µm) enables studies not previously accessible to the more conventional techniques for investigating deuterium retention.more » Of particular applicability is the use of GD-OES to measure the depth profile for experiments where high diffusion is expected: deuterium retention in neutron irradiated materials, and ultra-high deuterium fluences in burning plasma environment.« less

Indications of Bulk-Fluid Motion in Direct-Drive Implosions

NASA Astrophysics Data System (ADS)

Mannion, O. M.; Anderson, K. S.; Forrest, C. J.; Glebov, V. Yu.; Goncharov, V. N.; Knauer, J. P.; Radha, P. B.; Regan, S. P.; Sangster, T. C.; Stoeckl, C.

2017-10-01

The neutron spectrum produced by a burning plasma encodes essential information about the fusion products and serves as an important diagnostic for inertial confinement fusion experiments. At the Omega Laser Facility, neutron time-of-flight measurements are used to interpret the first and second moment of the neutron spectrum. These moments have been shown to be directly related to properties of the plasma, such as bulk fluid motion and apparent ion temperature. New measurement devices allow for unprecedented accuracy in the measurement of these moments and will provide a better understanding of the performance of direct-drive implosions. We present measurements of the first moment of the DT and D2 peaks in DT implosions and show that variations in the first moment indicate bulk fluid motion of the plasma. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Direct depth distribution measurement of deuterium in bulk tungsten exposed to high-flux plasma

NASA Astrophysics Data System (ADS)

Taylor, C. N.; Shimada, M.

2017-05-01

Understanding tritium retention and permeation in plasma-facing components is critical for fusion safety and fuel cycle control. Glow discharge optical emission spectroscopy (GD-OES) is shown to be an effective tool to reveal the depth profile of deuterium in tungsten. Results confirm the detection of deuterium. A ˜46 μm depth profile revealed that the deuterium content decreased precipitously in the first 7 μm, and detectable amounts were observed to depths in excess of 20 μm. The large probing depth of GD-OES (up to 100s of μm) enables studies not previously accessible to the more conventional techniques for investigating deuterium retention. Of particular applicability is the use of GD-OES to measure the depth profile for experiments where high deuterium concentration in the bulk material is expected: deuterium retention in neutron irradiated materials, and ultra-high deuterium fluences in burning plasma environment.

Effect of parenteral glutamine supplementation combined with enteral nutrition on Hsp90 expression and lymphoid organ apoptosis in severely burned rats.

PubMed

Fan, Jun; Wu, Jing; Wu, Li-Dong; Li, Guo-Ping; Xiong, Meng; Chen, Xi; Meng, Qing-Yan

2016-11-01

The aim of this study is to investigate the effects of parenteral glutamine(GLN) supplementation combined with enteral nutrition (EN) on heat shock protein 90(Hsp90) expression, apoptosis of lymphoid organs and circulating lymphocytes, immunological function and survival in severely burned rats. Male SD rats were randomly assigned into 4 groups: a sham burn+EN+GLN-free amino acid (AA) group (n=10), a sham burn+EN+GLN group (n=10), a burn+EN+AA group (n=10), and a burn +EN +GLN group (n=10). Two hours after a 30% total body surface area (TBSA), full-thickness scald burn injury on the back was made, the burned rats in two experimental groups (the burn+EN+AA group and the burn+EN +GLN group) were fed with a conventional enteral nutrition solution by oral gavage for 7 days. Simultaneously, the rats in the burn+EN+GLN group were given 0.35g GLN/kg body weight/day once via a tail vein injection for 7 days, whereas those in the burn+EN+AA group were administered isocaloric/isonitrogenous GLN-free amino acid solution (Tyrosine) for comparison. The rats in two sham burn control groups (the sham burn+EN+AA group and the sham burn+EN +GLN group) were treated in the same procedure as above, except for burn injury. All rats in each of the four groups were given 175kcal/kg body wt/day. There was isonitrogenous, isovolumic and isocaloric intake among four groups. At the end of the 7th day after nutritional programme were finished, all rats were anesthetized and samples were collected for further analysis. Serum immunoglobulin quantification was conducted by ELISA. Circulating lymphocyte numbers were counted by Coulter LH-750 Analyzer. The percentages and apoptotic ratio of CD4 and CD8T lymphocytes in circulation were determined by flow cytometry (FCM). The neutrophil phagocytosis index (NPI) was examined. The GLN concentrations in plasma, thymus, spleen and skeletal muscle were measured by high performance liquid chromatography (HPLC). The organ index evaluation and TUNEL analysis of thymus and spleen were carried out. The expression of Hsp90 in thymus and spleen was analyzed by western blotting. Moreover, the survival in burned rats was observed. The results revealed that parenteral GLN supplementation combined with EN significantly increased the GLN concentrations of plasma and tissues, the serum immunoglobulin content, the circulating lymphocyte number, the CD4/CD8 ratio, the indexes of thymus and spleen, NPI and survival as compared with the burn+EN+AA group (p<0.05). The expression of Hsp90 in thymus and spleen in the burn+EN+GLN group was significantly up-regulated as compared with the burn+EN+AA group (p<0.05). The apoptosis in circulating CD4 and CD8 lymphocytes, thymus and spleen in the burn+EN+GLN group was significantly decreased as compared with the burn+EN+AA group (p<0.05). The results of this study show that parenteral GLN supplementation combined with EN may increase the GLN concentrations of plasma and tissues, up-regulate the expression of Hsp90, attenuate apoptosis in lymphoid organ and circulating lymphocyte, enhance the immunological function and improve survival in severely burned rats. Clinically, therapeutic efforts at the modulation of the immune dysfunction may contribute to a favorable outcome in severely burned patients. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Establishment and Assessment of Plasma Disruption and Warning Databases from EAST

NASA Astrophysics Data System (ADS)

Wang, Bo; Robert, Granetz; Xiao, Bingjia; Li, Jiangang; Yang, Fei; Li, Junjun; Chen, Dalong

2016-12-01

Disruption database and disruption warning database of the EAST tokamak had been established by a disruption research group. The disruption database, based on Structured Query Language (SQL), comprises 41 disruption parameters, which include current quench characteristics, EFIT equilibrium characteristics, kinetic parameters, halo currents, and vertical motion. Presently most disruption databases are based on plasma experiments of non-superconducting tokamak devices. The purposes of the EAST database are to find disruption characteristics and disruption statistics to the fully superconducting tokamak EAST, to elucidate the physics underlying tokamak disruptions, to explore the influence of disruption on superconducting magnets and to extrapolate toward future burning plasma devices. In order to quantitatively assess the usefulness of various plasma parameters for predicting disruptions, a similar SQL database to Alcator C-Mod for EAST has been created by compiling values for a number of proposed disruption-relevant parameters sampled from all plasma discharges in the 2015 campaign. The detailed statistic results and analysis of two databases on the EAST tokamak are presented. supported by the National Magnetic Confinement Fusion Science Program of China (No. 2014GB103000)

Simulations of the impact of localized defects on ICF implosions

NASA Astrophysics Data System (ADS)

Milovich, Jose; Robey, Harry; Weber, Christopher; Sepke, Scott; Clark, Daniel; Koning, Joe; Smalyuk, Vladimir; Martinez, David

2016-10-01

Recent experiments have identified the tent membranes that support the capsule as a source of a large azimuthal perturbation at the point of departure from the surface. Highly-resolved 2D simulations have shown that vorticity generated by the interaction of the ablated capsule material and the tent allows for the penetration of cold ablator material into the burning hot-spot likely cooling the central burning plasma. These observations have motivated the search for alternative supporting methods. One of the techniques being considered uses the existing fill-tube (needed to deliver the cryogenic fuel) supported against gravity by a thin rod (cantilever) spanning the hohlraum diameter. Recent experiments have assessed the perturbation induced on the target as the rod is positioned along the fill-tube at different distances from the capsule surface and found optical-depth modulations oriented along the cantilever direction, possibly caused by laser spot shadowing or hydro-coupling. To fully understand the data we have undertaken an extensive study of highly-resolved 2D integrated simulations abled to resolve the 12 um diameter cantilever. Results of our computations and comparison with the experiments will be presented. Prepared by LLNL under Contract DE-AC52-07NA27344.

Determination of burn patient outcome by large-scale quantitative discovery proteomics

PubMed Central

Finnerty, Celeste C.; Jeschke, Marc G.; Qian, Wei-Jun; Kaushal, Amit; Xiao, Wenzhong; Liu, Tao; Gritsenko, Marina A.; Moore, Ronald J.; Camp, David G.; Moldawer, Lyle L.; Elson, Constance; Schoenfeld, David; Gamelli, Richard; Gibran, Nicole; Klein, Matthew; Arnoldo, Brett; Remick, Daniel; Smith, Richard D.; Davis, Ronald; Tompkins, Ronald G.; Herndon, David N.

2013-01-01

Objective Emerging proteomics techniques can be used to establish proteomic outcome signatures and to identify candidate biomarkers for survival following traumatic injury. We applied high-resolution liquid chromatography-mass spectrometry (LC-MS) and multiplex cytokine analysis to profile the plasma proteome of survivors and non-survivors of massive burn injury to determine the proteomic survival signature following a major burn injury. Design Proteomic discovery study. Setting Five burn hospitals across the U.S. Patients Thirty-two burn patients (16 non-survivors and 16 survivors), 19–89 years of age, were admitted within 96 h of injury to the participating hospitals with burns covering >20% of the total body surface area and required at least one surgical intervention. Interventions None. Measurements and Main Results We found differences in circulating levels of 43 proteins involved in the acute phase response, hepatic signaling, the complement cascade, inflammation, and insulin resistance. Thirty-two of the proteins identified were not previously known to play a role in the response to burn. IL-4, IL-8, GM-CSF, MCP-1, and β2-microglobulin correlated well with survival and may serve as clinical biomarkers. Conclusions These results demonstrate the utility of these techniques for establishing proteomic survival signatures and for use as a discovery tool to identify candidate biomarkers for survival. This is the first clinical application of a high-throughput, large-scale LC-MS-based quantitative plasma proteomic approach for biomarker discovery for the prediction of patient outcome following burn, trauma or critical illness. PMID:23507713

The potential of imposed magnetic fields for enhancing ignition probability and fusion energy yield in indirect-drive inertial confinement fusion

NASA Astrophysics Data System (ADS)

Perkins, L. J.; Ho, D. D.-M.; Logan, B. G.; Zimmerman, G. B.; Rhodes, M. A.; Strozzi, D. J.; Blackfield, D. T.; Hawkins, S. A.

2017-06-01

We examine the potential that imposed magnetic fields of tens of Tesla that increase to greater than 10 kT (100 MGauss) under implosion compression may relax the conditions required for ignition and propagating burn in indirect-drive inertial confinement fusion (ICF) targets. This may allow the attainment of ignition, or at least significant fusion energy yields, in presently performing ICF targets on the National Ignition Facility (NIF) that today are sub-marginal for thermonuclear burn through adverse hydrodynamic conditions at stagnation [Doeppner et al., Phys. Rev. Lett. 115, 055001 (2015)]. Results of detailed two-dimensional radiation-hydrodynamic-burn simulations applied to NIF capsule implosions with low-mode shape perturbations and residual kinetic energy loss indicate that such compressed fields may increase the probability for ignition through range reduction of fusion alpha particles, suppression of electron heat conduction, and potential stabilization of higher-mode Rayleigh-Taylor instabilities. Optimum initial applied fields are found to be around 50 T. Given that the full plasma structure at capsule stagnation may be governed by three-dimensional resistive magneto-hydrodynamics, the formation of closed magnetic field lines might further augment ignition prospects. Experiments are now required to further assess the potential of applied magnetic fields to ICF ignition and burn on NIF.

Energetic-ion-driven global instabilities in stellarator/helical plasmas and comparison with tokamak plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toi, K.; Ogawa, K.; Isobe, M.

2011-01-01

Comprehensive understanding of energetic-ion-driven global instabilities such as Alfven eigenmodes (AEs) and their impact on energetic ions and bulk plasma is crucially important for tokamak and stellarator/helical plasmas and in the future for deuterium-tritium (DT) burning plasma experiments. Various types of global modes and their associated enhanced energetic ion transport are commonly observed in toroidal plasmas. Toroidicity-induced AEs and ellipticity-induced AEs, whose gaps are generated through poloidal mode coupling, are observed in both tokamak and stellarator/helical plasmas. Global AEs and reversed shear AEs, where toroidal couplings are not as dominant were also observed in those plasmas. Helicity induced AEs thatmore » exist only in 3D plasmas are observed in the large helical device (LHD) and Wendelstein 7 Advanced Stellarator plasmas. In addition, the geodesic acoustic mode that comes from plasma compressibility is destabilized by energetic ions in both tokamak and LHD plasmas. Nonlinear interaction of these modes and their influence on the confinement of the bulk plasma as well as energetic ions are observed in both plasmas. In this paper, the similarities and differences in these instabilities and their consequences for tokamak and stellarator/helical plasmas are summarized through comparison with the data sets obtained in LHD. In particular, this paper focuses on the differences caused by the rotational transform profile and the 2D or 3D geometrical structure of the plasma equilibrium. Important issues left for future study are listed.« less

The P38alpha and P38delta MAP kinases may be gene therapy targets in the future treatment of severe burns.

PubMed

Wang, Shuyun; Huang, Qiaobing; Guo, Xiaohua; Brunk, Ulf T; Han, Jiahuai; Zhao, Keseng; Zhao, Ming

2010-08-01

Microvascular barrier damage, induced by thermal injury, imposes life-threatening problems owing to the pathophysiological consequences of plasma loss and impaired perfusion that finally may lead to multiple organ failure. The aim of the present study was to define the signaling role of selected mitogen-activated protein kinases (MAPKs) in general vessel hyperpermeability caused by burns and to look for a potential gene therapy. Rearrangement of cytoskeletons and cell tight junctions were evaluated by phalloidin labeling of actin and immunocytochemical demonstration of the ZO-1 protein, whereas blood vessel permeability was evaluated by a fluorescence ratio technique. The p38 MAPK inhibitor SB203580 largely blocked burn serum-induced stress-fiber formation and tight-junction damage. Using the adenoviral approach to transfect dominant negative forms of p38 MAPKs, we found that p38alpha and p38delta had similar effects. The in vivo part of the study showed that transfection of these two constructs significantly lowered general venular hyperpermeability and enhanced the survival of burned animals. Because the p38 MAPK pathway seems to play a crucial role in burn-induced vascular hyperpermeability, general transfection with p38 MAP dominant negative constructs might become a new therapeutic method to block burn-induced plasma leakage.

Plasma IL-8 signature correlates with pain and depressive symptomatology in patients with burning mouth syndrome: Results from a pilot study.

PubMed

Barry, Alison; O'Halloran, Ken D; McKenna, Joseph P; McCreary, Christine; Downer, Eric J

2018-02-01

Burning mouth syndrome (BMS) is a neuropathic orofacial pain condition of unknown aetiology that encompasses intra-oral burning pain without abnormal clinical findings. Psychological, neural and inflammatory processes are associated with BMS pathogenesis. Currently, studies characterising plasma cytokine/chemokine profiles with pain and depression in patients with BMS are lacking. Considering that inflammation is associated with the pathophysiology of BMS, and that inflammation is closely associated with pain and depression, we aimed to correlate depressive symptomatology and oral cavity pain with plasma cytokine/chemokine signatures in a cohort of patients with BMS. In this study, plasma protein levels of Th1 cytokines (IFN-γ, IL-2, IL-12p70, TNF-α), Th2 cytokines (IL-4, IL-10, IL-6, IL-13) and the chemokine IL-8 were assessed in patients with BMS (n = 10) and healthy volunteers (n = 10), using pro-inflammatory-10-plex assays. Clinical histories, alongside self-rated oral cavity pain intensities and depressive symptomatology were assessed using a visual analogue scale and the 16-item Quick Inventory of Depressive Symptomatology questionnaires, respectively. We present evidence that BMS is associated with increased depressive symptomatology and enhanced oral cavity pain. Plasma isolated from BMS patients display enhanced expression of the pro-inflammatory chemokine IL-8, when compared to plasma from healthy individuals. Plasma IL-8 signature correlates with pain and depressive symptomatology in the study cohort. Overall, these findings indicate that plasma IL-8 profiles are dysregulated in BMS and that modulation of IL-8 production in the disorder may be a tool in the management of BMS symptomatology. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Magnetized Target Fusion Driven by Plasma Liners

NASA Technical Reports Server (NTRS)

Thio, Y. C. Francis; Kirkpatrick, Ronald C.; Knapp, Charles E.; Rodgers, Stephen L. (Technical Monitor)

2002-01-01

Magnetized target fusion is an emerging, relatively unexplored approach to fusion for electrical power and propulsion application. The physical principles of the concept are founded upon both inertial confinement fusion (ICF) and magnetic confinement fusion (MCF). It attempts to combine the favorable attributes of both these orthogonal approaches to fusion, but at the same time, avoiding the extreme technical challenges of both by exploiting a fusion regime intermediate between them. It uses a material liner to compress, heat and contain the fusion reacting plasma (the target plasma) mentally. By doing so, the fusion burn could be made to occur at plasma densities as high as six orders of magnitude higher than conventional MCF such as tokamak, thus leading to an approximately three orders of magnitude reduction in the plasma energy required for ignition. It also uses a transient magnetic field, compressed to extremely high intensity (100's T to 1000T) in the target plasma, to slow down the heat transport to the liner and to increase the energy deposition of charged-particle fusion products. This has several compounding beneficial effects. It leads to longer energy confinement time compared with conventional ICF without magnetized target, and thus permits the use of much lower plasma density to produce reasonable burn-up fraction. The compounding effects of lower plasma density and the magneto-insulation of the target lead to greatly reduced compressional heating power on the target. The increased energy deposition rate of charged-particle fusion products also helps to lower the energy threshold required for ignition and increasing the burn-up fraction. The reduction in ignition energy and the compressional power compound to lead to reduced system size, mass and R&D cost. It is a fusion approach that has an affordable R&D pathway, and appears attractive for propulsion application in the nearer term.

A review of astrophysics experiments on intense lasers

NASA Astrophysics Data System (ADS)

Remington, B. A.

1999-11-01

Modern, high power laser facilities open new possibilities for simulating astrophysical systems in the laboratory.(S.J. Rose, Laser & Part. Beams 9, 869 (1991); B.H. Ripin et al., Laser & Part. Beams 8, 183 (1990); B.A. Remington et al., Science 284, 1488 (1999); H. Takabe et al., Plasma Phys. Contr. Fusion 41, A75 (1999); R.P. Drake, J. Geophys. Res. 104, 14505 (1999).) Scaled investigations of the hydrodynamics.(J. Kane et al., Phys. Plasmas 6, 2065 (1999); R.P. Drake et al., Ap. J. 500, L157 (1998); D. Ryutov et al., Ap. J. 518, 821 (1999).) and radiative transfer.(J. Wark et al., Phys. Plasmas 4, 2004 (1997); P.K. Patel et al., JQSRT 58, 835 (1997).) relevant to supernovae, and opacities relevant to stellar interiors.(F.J. Rogers and C.A. Iglesias, Science 263, 50 (1994); H. Merdji et al., JSQRT 58, 783 (1997).) are now possible with laser experiments. Equations of state relevant to the interiors of giant planets and brown dwarfs are also being experimentally accessed.(G.W. Collins et al., Science 281, 1178 (1998); A. Benuzzi et al., Phys. Rev. E 54, 2162 (1996).) With the construction of the NIF laser in the U.S., and the LIL and LMJ lasers in France, controlled investigations of thermonuclear burn physics will become possible in the next decade. And with existing and future ultra-high intensity short pulse lasers, investigations of relativistic astrophysical plasmas are becoming possible.(M.H. Key et al., Phys. Plasmas 5, 1966 (1998); F. Pegoraro et al., Plasma Phys. Contr. Fus. 39, B261 (1997).) A review of laboratory astrophysics experiments using intense lasers will be presented, and the potential for the future will be discussed.

A qualitative exploration of psychosocial specialists' experiences of providing support in UK burn care services.

PubMed

Guest, Ella; Griffiths, Catrin; Harcourt, Diana

2018-01-01

A burn can have a significant and long-lasting psychosocial impact on a patient and their family. The National Burn Care Standards (2013) recommend psychosocial support should be available in all UK burn services; however, little is known about how it is provided. The current study aimed to explore experiences of psychosocial specialists working in UK burn care, with a focus on the challenges they experience in their role. Semi-structured telephone interviews with eight psychosocial specialists (two psychotherapists and six clinical psychologists) who worked within UK burn care explored their experiences of providing support to patients and their families. Thematic analysis revealed two main themes: burn service-related experiences and challenges reflected health professionals having little time and resources to support all patients; reduced patient attendance due to them living large distances from service; psychosocial appointments being prioritised below wound-related treatments; and difficulties detecting patient needs with current outcome measures. Therapy-related experiences and challenges outlined the sociocultural and familial factors affecting engagement with support, difficulties treating patients with pre-existing mental health conditions within the burn service and individual differences in the stage at which patients are amenable to support. Findings provide an insight into the experiences of psychosocial specialists working in UK burn care and suggest a number of ways in which psychosocial provision in the NHS burn service could be developed.

Response measurement of single-crystal chemical vapor deposition diamond radiation detector for intense X-rays aiming at neutron bang-time and neutron burn-history measurement on an inertial confinement fusion with fast ignition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimaoka, T., E-mail: t.shimaoka@eng.hokudai.ac.jp; Kaneko, J. H.; Tsubota, M.

A neutron bang time and burn history monitor in inertial confinement fusion with fast ignition are necessary for plasma diagnostics. In the FIREX project, however, no detector attained those capabilities because high-intensity X-rays accompanied fast electrons used for plasma heating. To solve this problem, single-crystal CVD diamond was grown and fabricated into a radiation detector. The detector, which had excellent charge transportation property, was tested to obtain a response function for intense X-rays. The applicability for neutron bang time and burn history monitor was verified experimentally. Charge collection efficiency of 99.5% ± 0.8% and 97.1% ± 1.4% for holes andmore » electrons were obtained using 5.486 MeV alpha particles. The drift velocity at electric field which saturates charge collection efficiency was 1.1 ± 0.4 × 10{sup 7} cm/s and 1.0 ± 0.3 × 10{sup 7} cm/s for holes and electrons. Fast response of several ns pulse width for intense X-ray was obtained at the GEKKO XII experiment, which is sufficiently fast for ToF measurements to obtain a neutron signal separately from X-rays. Based on these results, we confirmed that the single-crystal CVD diamond detector obtained neutron signal with good S/N under ion temperature 0.5–1 keV and neutron yield of more than 10{sup 9} neutrons/shot.« less

Platelet-Rich Plasma Injection in Burn Scar Areas Alleviates Neuropathic Scar Pain

PubMed Central

Huang, Shu-Hung; Wu, Sheng-Hua; Lee, Su-Shin; Lin, Yun-Nan; Chai, Chee-Yin; Lai, Chung-Sheng; Wang, Hui-Min David

2018-01-01

Objective: No effective treatments have yet been developed for burn-induced neuropathic pain. Platelet-rich plasma (PRP) has been reported to ameliorate various types of inflammation pain. However, the effect of PRP on burn-induced neuropathic pain is unclear. Methods: Burn-induced neuropathic pain Sprague-Dawley rat model was confirmed using a mechanical response test 4 weeks after the burn injuries were sustained, following which PRP was injected in the scar area. The rats were divided into four groups (n = 6) as following: Group A, Sham; Group B, Sham + PRP; Group C, Burn; and Group D, Burn + PRP. Four weeks after the PRP injection, the animals were subjected to behavior tests and then sacrificed; specimens were collected for inflammation tests, Masson's trichrome stain and chromosome 10 (PTEN) in the injured skin; and PTEN, phosphorylated mammalian target of rapamycin (p-mTOR), p38, nuclear factor κB (NFκB), chemokine (CC motif) ligand 2 (CCL2), and CCL2 cognate receptor (CCR2) in spinal cord dorsal horns through immunohistochemistry and immunofluorescence staining. Results: PRP significantly alleviated allodynia in burn-induced neuropathic pain 4 weeks after treatment, and PTEN expression in the skin and spinal cord were significantly increased in group D compared with the group C. p-PTEN, p-mTOR, and CCL2 expression in neuron cells; p-p38 and p-NFκB expression in microglia; and p-JNK and p-NFκB activation in spinal astrocytes decreased significantly in the group D compared with the group C. Conclusions: PRP is effective in treating burn-induced neuropathic pain and may be used in clinical practice. PMID:29483815

[Evaluation of NMR relaxation method as a diagnostic tool for donor blood analysis and patients with hematologic diseases and burns].

PubMed

Gangardt, M G; Popova, O V; Shmarov, D A; Kariakina, N F; Papish, E A; Kozinets, G I

2002-08-01

Diagnostic value of the NMR-relaxation method in the blood plasma was estimated in the patients with different pathologies. The time of hydrogen nuclei longitudinal relaxation (T1) in the health donors of the blood, in the patients with oncopathology (hemoblastoses) and in the cases with anemia and burning disease were investigated. The time of the longitudinal relaxation (T1) was measured by automated NMR-relaxometer "Palma" (Russia). The working frequency was equal to 35 MHz, the temperature was 45 +/- 0.1 degrees C. For the single measurement 0.2 ml of blood obtained from heparinized venous blood 1.5 hours after its taking was used. The time of the longitudinal relaxation (T1) was shown to be 1.78 +/- 0.02 in the health donors, 1.70 +/- 0.06 s in cases with anemia, 1.97 +/- 0.48 c in patients with leucosis, 2.40 +/- 0.12 s in patients with burns. The sensitivity and the specificity of diagnostics of leucosis based upon the results of the only single T1 measurement in blood plasma were concluded to be 75%. It proves the significant T1 change both in patients with anemia and burning disease of the II-III degree. However it is evidently insufficient for selective use of NMR-relaxation blood plasma (serum) in the diagnostics of anemia and leucosis. The data obtained prove also the possibility of use of NMR-relaxation blood plasma (serum) for control of the hemostasis state during treatment or remission.

Discovery of stationary operation of quiescent H-mode plasmas with net-zero neutral beam injection torque and high energy confinement on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burrell, K. H.; Chen, X.; Garofalo, A. M.

Recent experiments in DIII-D [J. L. Luxon et al., in Plasma Physics and Controlled Nuclear Fusion Research 1996 (International Atomic Energy Agency, Vienna, 1987), Vol. I, p. 159] have led to the discovery of a means of modifying edge turbulence to achieve stationary, high confinement operation without Edge Localized Mode (ELM) instabilities and with no net external torque input. Eliminating the ELM-induced heat bursts and controlling plasma stability at low rotation represent two of the great challenges for fusion energy. By exploiting edge turbulence in a novel manner, we achieved excellent tokamak performance, well above the H{sub 98y2} international tokamakmore » energy confinement scaling (H{sub 98y2} = 1.25), thus meeting an additional confinement challenge that is usually difficult at low torque. The new regime is triggered in double null plasmas by ramping the injected torque to zero and then maintaining it there. This lowers E × B rotation shear in the plasma edge, allowing low-k, broadband, electromagnetic turbulence to increase. In the H-mode edge, a narrow transport barrier usually grows until MHD instability (a peeling ballooning mode) leads to the ELM heat burst. However, the increased turbulence reduces the pressure gradient, allowing the development of a broader and thus higher transport barrier. A 60% increase in pedestal pressure and 40% increase in energy confinement result. An increase in the E × B shearing rate inside of the edge pedestal is a key factor in the confinement increase. Strong double-null plasma shaping raises the threshold for the ELM instability, allowing the plasma to reach a transport-limited state near but below the explosive ELM stability boundary. The resulting plasmas have burning-plasma-relevant β{sub N} = 1.6–1.8 and run without the need for extra torque from 3D magnetic fields. To date, stationary conditions have been produced for 2 s or 12 energy confinement times, limited only by external hardware constraints. Stationary operation with improved pedestal conditions is highly significant for future burning plasma devices, since operation without ELMs at low rotation and good confinement is key for fusion energy production.« less

Theoretical Issues for Plasma Regimes to be Explored by the Ignitor Experiment

NASA Astrophysics Data System (ADS)

Cardinali, A.; Coppi, B.; Sonnino, G.

2014-10-01

At present, the Ignitor experiment is the only one designed and planned to approach and explore ignition regimes under controlled DT burning conditions. The machine parameters have been established on the basis of existing knowledge of the confinement properties of high density plasmas. A variety of improved confinement regimes are expected to be accessible by means of the available ICRH heating power in addition to the prevalent programmable Ohmic heating power and relying on the injection of high velocity pellets for density profile control. The relevance of the various known confinement regimes to the objectives of Ignitor is discussed. Among other theoretical efforts, a non-linear thermal energy balance equation is investigated to study the onset of thermonuclear instability in the plasmas expected to be produced in Ignitor. The equation for the temperature profile in the equilibrium state is solved with the resulting profiles in agreement with those obtained by a full transport code and commonly adopted scalings for them. The evolution of the thermonuclear instability that relies on the solution of the time dependent energy balance equation is obtained. Sponsored in part by the U.S. DOE.

Semi-analytic model of plasma-jet-driven magneto-inertial fusion

DOE PAGES

Langendorf, Samuel J.; Hsu, Scott C.

2017-03-01

A semi-analytic model for plasma-jet-driven magneto-inertial fusion is presented here. Compressions of a magnetized plasma target by a spherically imploding plasma liner are calculated in one dimension (1D), accounting for compressible hydrodynamics and ionization of the liner material, energy losses due to conduction and radiation, fusion burn and alpha deposition, separate ion and electron temperatures in the target, magnetic pressure, and fuel burn-up. Results show 1D gains of 3–30 at spherical convergence ratio <15 and 20–40 MJ of liner energy, for cases in which the liner thickness is 1 cm and the initial radius of a preheated magnetized target ismore » 4 cm. Some exploration of parameter space and physics settings is presented. The yields observed suggest that there is a possibility of igniting additional dense fuel layers to reach high gain.« less

DIII-D Upgrade to Prepare the Basis for Steady-State Burning Plasmas

NASA Astrophysics Data System (ADS)

Buttery, R. J.; Guo, H. Y.; Taylor, T. S.; Wade, M. R.; Hill, D. N.

2014-10-01

Future steady-state burning plasma facilities will access new physics regimes and modes of plasma behavior. It is vital to prepare for this both experimentally using existing facilities, and theoretically in order to develop the tools to project to and optimize these devices. An upgrade to DIII-D is proposed to address the three critical aspects where research must go beyond what we can do now: (i) torque free electron heating to address the energy, particle and momentum transport mechanisms of burning plasmas using electron cyclotron (EC) heating and full power balanced neutral beams; (ii) off-axis heating and current drive to develop the path to true fusion steady state by reorienting neutral beams and deploying EC and helicon current drive; (iii) a new divertor with hot walls and reactor relevant materials to develop the basis for benign detached divertor operation compatible with wall materials and a high performance fusion core. These elements with modest incremental cost and enacted as a user facility for the whole US program will enable the US to lead on ITER and take a decision to proceed with a Fusion Nuclear Science Facility. Work supported by the US Department of Energy under DE-FC02-04ER54698 and DE-AC52-07NA27344.

Plasma viscosity with mass transport in spherical inertial confinement fusion implosion simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vold, E. L.; Molvig, K.; Joglekar, A. S.

2015-11-15

The effects of viscosity and small-scale atomic-level mixing on plasmas in inertial confinement fusion (ICF) currently represent challenges in ICF research. Many current ICF hydrodynamic codes ignore the effects of viscosity though recent research indicates viscosity and mixing by classical transport processes may have a substantial impact on implosion dynamics. We have implemented a Lagrangian hydrodynamic code in one-dimensional spherical geometry with plasma viscosity and mass transport and including a three temperature model for ions, electrons, and radiation treated in a gray radiation diffusion approximation. The code is used to study ICF implosion differences with and without plasma viscosity andmore » to determine the impacts of viscosity on temperature histories and neutron yield. It was found that plasma viscosity has substantial impacts on ICF shock dynamics characterized by shock burn timing, maximum burn temperatures, convergence ratio, and time history of neutron production rates. Plasma viscosity reduces the need for artificial viscosity to maintain numerical stability in the Lagrangian formulation and also modifies the flux-limiting needed for electron thermal conduction.« less

ELM Mitigation in Low-rotation ITER Baseline Scenario Plasmas on DIII-D with Deuterium Pellet Injection

NASA Astrophysics Data System (ADS)

Baylor, L. R.

2016-10-01

ELM mitigation using high frequency D2 pellet ELM pacing has been demonstrated in ITER baseline scenario plasmas on DIII D with low rotation obtained with low NBI input torque. The ITER burning plasmas will have relatively low input torque and are expected to have low rotation. ELM mitigation by on-demand pellet ELM triggering has not been observed before in these conditions. New experiments on DIII-D in these conditions with 90 Hz D2 pellets have shown that significant mitigation of the divertor ELM peak heat flux by a factor of 8 is possible without detrimental effects to the plasma confinement. High-Z impurity accumulation is dramatically reduced at all input torques from 0.1 to 2.5 N-m. Fueling with high field side injection of D2 pellets has been employed to demonstrate that density buildup can be obtained simultaneously with ELM mitigation. The implications are that rapid pellet injection remains a promising technique to trigger on-demand ELMs in low rotating plasmas with greatly reduced peak flux while preventing impurity accumulation in ITER. Supported by the US DOE under DE-AC05-00OR22725, DE-FC02-04ER54698.

Enhancing Ignition Probability and Fusion Yield in NIF Indirect Drive Targets with Applied Magnetic Fields

NASA Astrophysics Data System (ADS)

Perkins, L. John; Logan, B. Grant; Ho, Darwin; Zimmerman, George; Rhodes, Mark; Blackfield, Donald; Hawkins, Steven

2017-10-01

Imposed magnetic fields of tens of Tesla that increase to greater than 10 kT (100 MGauss) under capsule compression may relax conditions for ignition and propagating burn in indirect-drive ICF targets. This may allow attainment of ignition, or at least significant fusion energy yields, in presently-performing ICF targets on the National Ignition Facility that today are sub-marginal for thermonuclear burn through adverse hydrodynamic conditions at stagnation. Results of detailed 2D radiation-hydrodynamic-burn simulations applied to NIF capsule implosions with low-mode shape perturbations and residual kinetic energy loss indicate that such compressed fields may increase the probability for ignition through range reduction of fusion alpha particles, suppression of electron heat conduction and stabilization of higher-mode RT instabilities. Optimum initial applied fields are around 50 T. Off-line testing has been performed of a hohlraum coil and pulsed power supply that could be integrated on NIF; axial fields of 58T were obtained. Given the full plasma structure at capsule stagnation may be governed by 3-D resistive MHD, the formation of closed magnetic field lines might further augment ignition prospects. Experiments are now required to assess the potential of applied magnetic fields to NIF ICF ignition and burn. Work performed under auspices of U.S. DOE by LLNL under Contract DE-AC52-07NA27344.

Sensitivity of alpha-particle-driven Alfvén eigenmodes to q-profile variation in ITER scenarios

NASA Astrophysics Data System (ADS)

Rodrigues, P.; Figueiredo, A. C. A.; Borba, D.; Coelho, R.; Fazendeiro, L.; Ferreira, J.; Loureiro, N. F.; Nabais, F.; Pinches, S. D.; Polevoi, A. R.; Sharapov, S. E.

2016-11-01

A perturbative hybrid ideal-MHD/drift-kinetic approach to assess the stability of alpha-particle-driven Alfvén eigenmodes in burning plasmas is used to show that certain foreseen ITER scenarios, namely the {{I}\\text{p}}=15 MA baseline scenario with very low and broad core magnetic shear, are sensitive to small changes in the background magnetic equilibrium. Slight variations (of the order of 1% ) of the safety-factor value on axis are seen to cause large changes in the growth rate, toroidal mode number, and radial location of the most unstable eigenmodes found. The observed sensitivity is shown to proceed from the very low magnetic shear values attained throughout the plasma core, raising issues about reliable predictions of alpha-particle transport in burning plasmas.

Understanding fuel magnetization and mix using secondary nuclear reactions in magneto-inertial fusion.

PubMed

Schmit, P F; Knapp, P F; Hansen, S B; Gomez, M R; Hahn, K D; Sinars, D B; Peterson, K J; Slutz, S A; Sefkow, A B; Awe, T J; Harding, E; Jennings, C A; Chandler, G A; Cooper, G W; Cuneo, M E; Geissel, M; Harvey-Thompson, A J; Herrmann, M C; Hess, M H; Johns, O; Lamppa, D C; Martin, M R; McBride, R D; Porter, J L; Robertson, G K; Rochau, G A; Rovang, D C; Ruiz, C L; Savage, M E; Smith, I C; Stygar, W A; Vesey, R A

2014-10-10

Magnetizing the fuel in inertial confinement fusion relaxes ignition requirements by reducing thermal conductivity and changing the physics of burn product confinement. Diagnosing the level of fuel magnetization during burn is critical to understanding target performance in magneto-inertial fusion (MIF) implosions. In pure deuterium fusion plasma, 1.01 MeV tritons are emitted during deuterium-deuterium fusion and can undergo secondary deuterium-tritium reactions before exiting the fuel. Increasing the fuel magnetization elongates the path lengths through the fuel of some of the tritons, enhancing their probability of reaction. Based on this feature, a method to diagnose fuel magnetization using the ratio of overall deuterium-tritium to deuterium-deuterium neutron yields is developed. Analysis of anisotropies in the secondary neutron energy spectra further constrain the measurement. Secondary reactions also are shown to provide an upper bound for the volumetric fuel-pusher mix in MIF. The analysis is applied to recent MIF experiments [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)] on the Z Pulsed Power Facility, indicating that significant magnetic confinement of charged burn products was achieved and suggesting a relatively low-mix environment. Both of these are essential features of future ignition-scale MIF designs.

Demonstration of plasma start-up by Coaxial Helicity Injection

NASA Astrophysics Data System (ADS)

Raman, Roger

2003-10-01

Experimental results on the first successful transfer of a Coaxial-Helicity-Injection- (CHI)-produced discharge to inductive operation are reported. CHI assisted plasma start-up is more robust than inductive-only operation and reduces volt-seconds consumption. After hand-off for inductive operation, the initial 100 kA of CHI-produced current drops to 44 kA, then ramps up to 180 kA, using only 30 mVs, more than 30induction alone. Coupling a CHI-produced discharge to induction from a pre-charged central solenoid has produced record plasma currents of 265kA in HIT-II. CHI discharges can also be generated while the central transformer is in the process of being pre-charged, during which period it induces a negative loop voltage on the CHI discharge. Such capability is believed to be important for a short pulse burning plasma experiment that could contain a solenoid. In the latest results, which improve upon the earlier work (Raman et. al., Phys. Rev. Lett., 90, (2003) 075005-1), no transient coil currents are necessary for the CHI produced closed flux generation. This is particularly important for a reactor in which the poloidal field coils would be located outside blanket structures. Three important results are reported. First, CHI is shown to produce closed flux plasma. Second, it is shown that electrode-based CHI plasmas can be sufficiently clean for fusion research purposes. Finally, it is shown that CHI discharges, in addition to generating useful startup current, improve the performance of inductive discharges. This work was motivated by earlier experiments on HIT-II and NSTX that showed coupling of the inductive drive to the external CHI power supply circuit, instead of to the main plasma discharge. These important results were obtained on the HIT-II spherical torus experiment (R/a of 0.3/0.2m, elongation of 1.5).

[Qualitative research on pain experiences of adult burn patients].

PubMed

Li, L; Pan, Q; Xu, L; Lin, R Q; Dai, J X; Chen, Z H

2018-03-20

Objective: To explore the pain experiences of adult burn patients so as to lay foundation for practical analgesic measures. Methods: Using phenomenological method in qualitative research, semi-structured interviews were conducted on 12 adult burn patients hospitalized in our burn units from May to November 2015, aiming at pain experiences from immediately after burns to 3 to 7 months after being discharged from hospital. Then the Colaizzi's analysis method was applied to analyze, induce, and refine themes of interview data. Results: After analysis, pain experiences of adult burn patients were generalized into 6 themes: deep pain experiences, heavy psychological burden, limited daily life, poor assessment and treatment of pain, different attributions of pain, and different ways of coping of pain. Conclusions: Burn pain brings harm to the patients' physiology, mentality, and daily life. Nevertheless, pain processing modes of medical staff and patients themselves are the key factors affecting patients' pain experiences. Therefore, according to the deficiency of current situation of pain management, the targeted analgesic intervention measures should be carried out from the perspectives of medical staff and patients.

How much does a tokamak reactor cost?

NASA Astrophysics Data System (ADS)

Freidberg, J.; Cerfon, A.; Ballinger, S.; Barber, J.; Dogra, A.; McCarthy, W.; Milanese, L.; Mouratidis, T.; Redman, W.; Sandberg, A.; Segal, D.; Simpson, R.; Sorensen, C.; Zhou, M.

2017-10-01

The cost of a fusion reactor is of critical importance to its ultimate acceptability as a commercial source of electricity. While there are general rules of thumb for scaling both overnight cost and levelized cost of electricity the corresponding relations are not very accurate or universally agreed upon. We have carried out a series of scaling studies of tokamak reactor costs based on reasonably sophisticated plasma and engineering models. The analysis is largely analytic, requiring only a simple numerical code, thus allowing a very large number of designs. Importantly, the studies are aimed at plasma physicists rather than fusion engineers. The goals are to assess the pros and cons of steady state burning plasma experiments and reactors. One specific set of results discusses the benefits of higher magnetic fields, now possible because of the recent development of high T rare earth superconductors (REBCO); with this goal in mind, we calculate quantitative expressions, including both scaling and multiplicative constants, for cost and major radius as a function of central magnetic field.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casey, D. T.; Sayre, D. B.; Brune, C. R.

Stars are giant thermonuclear plasma furnaces that slowly fuse the lighter elements in the universe into heavier elements, releasing energy, and generating the pressure required to prevent collapse. To understand stars, we must rely on nuclear reaction rate data obtained, up to now, under conditions very different from those of stellar cores. Here we show thermonuclear measurements of the 2H(d, n) 3He and 3H(t,2n) 4He S-factors at a range of densities (1.2–16 g cm –3) and temperatures (2.1–5.4 keV) that allow us to test the conditions of the hydrogen-burning phase of main-sequence stars. The relevant conditions are created using inertial-confinementmore » fusion implosions at the National Ignition Facility. Here, our data agree within uncertainty with previous accelerator-based measurements and establish this approach for future experiments to measure other reactions and to test plasma-nuclear effects present in stellar interiors, such as plasma electron screening, directly in the environments where they occur.« less

Erosive burning research. [for solid-propellant rocket engines

NASA Technical Reports Server (NTRS)

Strand, L.; Yang, L. C.; Nguyen, M. H.; Cohen, N. S.

1986-01-01

A status report is given on the results for the completed tests in a series of motor firings being carried out to measure the effects of the parameters that are considered to most strongly influence the scaling to larger rocket motor sizes of the transition to/or threshold conditions for erosive burning rate augmentation. Propellant burning rates at locations along the axis of the test motors are measured with a newly developed plasma capacitance gauge technique. The measured results are compared with erosive-burning predictions from a supporting ballistics analysis. The completed motor firings have successfully demonstrated response to the designed test variables. The trends with varying propellant burning rate, chamber pressure, and mass flow rate are consistent with existing results, but no pronounced effect of surface roughness has been observed. Rather, the influence of propellant oxidizer particle size on erosive burning is through its effect on the base, no-corssflow burning rate.

Scoping study for compact high-field superconducting net energy tokamaks

NASA Astrophysics Data System (ADS)

Mumgaard, R. T.; Greenwald, M.; Freidberg, J. P.; Wolfe, S. M.; Hartwig, Z. S.; Brunner, D.; Sorbom, B. N.; Whyte, D. G.

2016-10-01

The continued development and commercialization of high temperature superconductors (HTS) may enable the construction of compact, net-energy tokamaks. HTS, in contrast to present generation low temperature superconductors, offers improved performance in high magnetic fields, higher current density, stronger materials, higher temperature operation, and simplified assembly. Using HTS along with community-consensus confinement physics (H98 =1) may make it possible to achieve net-energy (Q>1) or burning plasma conditions (Q>5) in DIII-D or ASDEX-U sized, conventional aspect ratio tokamaks. It is shown that, by operating at high plasma current and density enabled by the high magnetic field (B>10T), the required triple products may be achieved at plasma volumes under 20m3, major radii under 2m, with external heating powers under 40MW. This is at the scale of existing devices operated by laboratories, universities and companies. The trade-offs in the core heating, divertor heat exhaust, sustainment, stability, and proximity to known plasma physics limits are discussed in the context of the present tokamak experience base and the requirements for future devices. The resulting HTS-based design space is compared and contrasted to previous studies on high-field copper experiments with similar missions. The physics exploration conducted with such HTS devices could decrease the real and perceived risks of ITER exploitation, and aid in quickly developing commercially-applicable tokamak pilot plants and reactors.

The effect of vitamin C on plasma volume in the early stage of sepsis in the rat.

PubMed

Bark, Björn P; Grände, Per-Olof

2014-12-01

Previous experimental studies have shown that vitamin C has several beneficial effects in sepsis and burns, such as decreased tissue oedema, improved endothelial barrier function and decreased transcapillary leakage of plasma markers. It has still not been investigated, though, if vitamin C has any impact specifically on plasma volume. The present study aims at testing the hypothesis that vitamin C decreases plasma volume loss in sepsis. Anaesthetized male adult Sprague-Dawley rats were used in this prospective randomized study. All experiments were carried out at a university hospital laboratory. Sepsis was induced by caecal ligation and incision. After 3 h, vitamin C was given either as a bolus dose (66 mg/kg) followed by a continuous infusion (33 mg/kg/h) (n = 9), or as a single bolus dose (200 mg/kg) (n = 9). A sham group (n = 9) underwent the same surgical procedure, but no vitamin C was given. Plasma volume was measured ((125)I-dilution technique) at baseline, at 3 h after end of initiation of sepsis and at the end of the experiment 3 h later. Arterial blood samples for analyses of electrolytes, blood gases, haematocrit and lactate were taken at the same time points. There were no significant differences in plasma volumes or the physiological parameters analysed between any of the three groups at any time point. There was a significantly larger urine production in the single bolus dose group (200 mg/kg) compared to the sham group. Vitamin C treatment did not decrease the loss of plasma volume in the septic rat. The diuretic effect of vitamin C was in accordance with previous studies.

Comparison of tokamak behaviour with tungsten and low-Z plasma facing materials

NASA Astrophysics Data System (ADS)

Philipps, V.; Neu, R.; Rapp, J.; Samm, U.; Tokar, M.; Tanabe, T.; Rubel, M.

2000-12-01

Graphite wall materials are used in present day fusion devices in order to optimize plasma core performance and to enable access to a large operational space. A large physics database exists for operation with these plasma facing materials, which also indicate their use in future devices with extended burn times. The radiation from carbon impurities in the edge and divertor regions strongly helps to reduce the peak power loads on the strike areas, but carbon radiation also supports the formation of MARFE instabilities which can hinder access to high densities. The main concerns with graphite are associated with its strong chemical affinity to hydrogen, which leads to chemical erosion and to the formation of hydrogen-rich carbon layers. These layers can store a significant fraction of the total tritium fuel, which might prevent the use of these materials in future tritium devices. High-Z plasma facing materials are much more advantageous in this sense, but these advantages compete with the strong poisoning of the plasma if they enter the plasma core. New promising experiences have been obtained with high-Z wall materials in several devices, about which a survey is given in this paper and which also addresses open questions for future research and development work.

Development of terahertz laser diagnostics for electron density measurements.

PubMed

Kawahata, K; Akiyama, T; Tanaka, K; Nakayama, K; Okajima, S

2008-10-01

A two color laser interferometer using terahertz laser sources is under development for high performance operation on the large helical device and for future burning plasma experiments such as ITER. Through investigation of terahertz laser sources, we have achieved high power simultaneous oscillations at 57.2 and 47.6 microm of a CH(3)OD laser pumped by a cw 9R(8) CO(2) laser line. The laser wavelength around 50 microm is the optimum value for future fusion devices from the consideration of the beam refraction effect and signal-to-noise ratio for an expected phase shift due to plasma. In this article, recent progress of the terahertz laser diagnostics, especially in mechanical vibration compensation by using a two color laser operation and terahertz laser beam transmission through a dielectric waveguide, will be presented.

Neutron generation from Z-pinches

NASA Astrophysics Data System (ADS)

Vikhrev, V. V.; Korolev, V. D.

2007-05-01

Recent advances in both experimental and theoretical studies on neutron generation in various Z-pinch facilities are reviewed. The main methods for enhancing neutron emission from the Z-pinch plasma are described, and the problems of igniting a thermonuclear burn wave in this plasma are discussed.

Ignition and pusher adiabat

NASA Astrophysics Data System (ADS)

Cheng, B.; Kwan, T. J. T.; Wang, Y. M.; Yi, S. A.; Batha, S. H.; Wysocki, F.

2018-07-01

In the last five years, large amounts of high quality data on inertial confinement fusion (ICF) experiments were produced at the National Ignition Facility (NIF). From this data we have significantly advanced our scientific understanding of the physics of thermonuclear (TN) ignition and identified critical issues that must be addressed to achieve a burning hotspot, such as implosion energetics, pusher adiabat, tamping effects, and confinement time. In this paper we present a review of recently developed TN ignition and implosion scaling theory (Cheng et al 2013 Phys. Rev. E 88 041101; Cheng et al 2014 Phys. Plasmas 21 10270) that characterizes the thermodynamic properties of the hotspot and the ignition criteria for ICF. We compare our theoretical predictions with NIF data and find good agreement between theory and experiments. We demonstrate the fundamental effects of the pusher adiabat on the energy partition between the cold shell and the hot deuterium–tritium (DT) gas, and thus on the integrated performance of ICF capsules. Theoretical analysis of NIF experiments (Cheng et al 2015 Phys. Plasmas 22 082704; Melvin et al 2015 Phys. Plasmas 22 022708; Cheng et al 2016 Phys. Plasmas 23 120702) and physical explanations of the discrepancies between theory, data, and simulations are presented. It is shown that the true experimental adiabat of the cold DT fuel can be inferred from neutron image data of a capsule implosion. We show that the ablator mix and preheat in the cold fuel can be estimated from the experimentally inferred hotspot mix. Finally, possible paths forward to reach higher yields at NIF implied by the theory are discussed.

Edge Mechanisms for Power Excursion Control in Burning Plasmas

NASA Astrophysics Data System (ADS)

Hill, M. D.; Stacey, W. M.

2017-10-01

ITER must have active and preferably also passive control mechanisms that will limit inadvertent plasma power excursions which could trigger runaway fusion heating. We are identifying and investigating the potential of ion-orbit loss, impurity seeding, and various divertor ``choking'' phenomena to control or limit sudden increases in plasma density or temperature by reducing energy confinement, increasing radiation loss, etc., with the idea that such mechanisms could be tested on DIII-D and other existing tokamaks. We are assembling an edge-divertor code (GTEDGE-2) with a neutral transport model and a burn dynamics code, for this purpose. One potential control mechanism is the enhanced ion orbit loss from the thermalized ion distribution that would result from heating of the thermalized plasma ion distribution. Another possibility is impurity seeding with ions whose emissivity would increase sharply if the edge temperature increased. Enhanced radiative losses should also reduce the thermal energy flux across the separatrix, perhaps dropping the plasma into the poorer L-mode confinement regime. We will present some initial calculations to quantify these ideas. Work supported by US DOE under DE-FC02-04ER54698.

A new flexible DBD device for treating infected wounds: in vitro and ex vivo evaluation and comparison with a RF argon plasma jet

NASA Astrophysics Data System (ADS)

Boekema, B. K. H. L.; Vlig, M.; Guijt, D.; Hijnen, K.; Hofmann, S.; Smits, P.; Sobota, A.; van Veldhuizen, E. M.; Bruggeman, P.; Middelkoop, E.

2016-02-01

Cold plasma has been shown to provide a promising alternative antimicrobial treatment for wound healing. We developed and tested a flexible surface dielectric barrier discharge (DBD) and compared it to an argon gas based plasma jet operated remotely with a distance between plasma plume and sample of 8 mm. Tests were conducted using different models: on cultured cells, on ex vivo human skin and on bacteria (Pseudomonas aeruginosa) (on agar, in suspension, in collagen/elastin matrix or on ex vivo human skin), allowing us to directly compare bactericidal with safety aspects under identical conditions. Both plasma devices were highly efficient when used on bacteria in non-buffered solutions, but DBD was faster in reaching the maximum bacterial reduction. Treatment of bacteria on intact skin with DBD resulted in up to 6 log reductions in 3 min. The jet was far less efficient on intact skin. Even after 8 min treatment no more than 2 log reductions were obtained with the jet. Treatment of bacteria in burn wound models with DBD for 6 min resulted in a 4.5 log reduction. Even when using DBD for 6 min on infected burn wound models with colonizing or biofilm phase bacteria, the log reductions were 3.8 or 3.2 respectively. DBD plasma treatment for 6 min did not affect fibroblast viability, whereas a treatment for 8 min was detrimental. Similarly, treatment with DBD or plasma jet for 6 min did also not affect the metabolic activity of skin biopsies. After treatment for 8 min with DBD or plasma jet, 78% or 60% of activity in skin biopsies remained, respectively. Multiple treatments of in vitro burn wound models with surface DBD for 6 min or with plasma jet for 8 min did not affect re-epithelialization. With the flexible surface DBD plasma strip we were able to quickly inactivate large numbers of bacteria on and in skin. Under the same conditions, viability of skin cells or re-epithelialization was not affected. The DBD source has potential for treating larger wound areas.

Nuclear system that burns its own wastes shows promise

NASA Technical Reports Server (NTRS)

Atchison, K.

1975-01-01

A nuclear fission energy system, capable of eliminating a significant amount of its radioactive wastes by burning them, is described. A theoretical investigation of this system conducted by computer analysis, is based on use of gaseous fuel nuclear reactors. Gaseous core reactors using a uranium plasma fuel are studied along with development for space propulsion.

Preserving self-concept in the burn survivors: a qualitative study.

PubMed

Zamanzadeh, Vahid; Valizadeh, Llila; Lotfi, Mojgan; Salehi, Feridoon

2015-01-01

Burn injury is a devastating experience affecting all aspects of a person's essence, including his/her identity and perception. These patients require complex cognitive efforts to redefine their identity to deal with difficult condition after burn injury and preserve self-concept. The experience of life after burn injury is generally a solitary one, closely related to the patients' cultural and religious context. Therefore, this study was conducted aiming at investigating burn patients' experiences regarding how to preserve self-concept in life after burn injury in Iran. This qualitative study was carried out using qualitative content analysis and in-depth unstructured interviews with 17 surviving burn subjects. During the qualitative content analysis process, the concept of "locating" as the essence of the participants' experience was extracted as follows: (A) self-exploration (exploring the changes in one's life), (B) others' exploration (exploring the changes in the life of family members and the relationship between self and others), (C) position evaluation (self-position analysis), and (D) self-concept preservation. The present study has developed new understandings of mental experiences of burn patients' self-concept by describing the concept of "self-locating". It helps us in classifying and understanding the concepts described in comprehensive theories developed in this area. They do this by focusing on what burn patients experience for choosing self-preservation strategies and having a meaningful life. The finding can be used as a conceptual framework for palliative care program in Iran.

Preserving Self-Concept in the Burn Survivors: A Qualitative Study

PubMed Central

Zamanzadeh, Vahid; Valizadeh, Llila; Lotfi, Mojgan; Salehi, Feridoon

2015-01-01

Background: Burn injury is a devastating experience affecting all aspects of a person's essence, including his/her identity and perception. These patients require complex cognitive efforts to redefine their identity to deal with difficult condition after burn injury and preserve self-concept. The experience of life after burn injury is generally a solitary one, closely related to the patients’ cultural and religious context. Therefore, this study was conducted aiming at investigating burn patients’ experiences regarding how to preserve self-concept in life after burn injury in Iran. Materials and Methods: This qualitative study was carried out using qualitative content analysis and in-depth unstructured interviews with 17 surviving burn subjects. Results: During the qualitative content analysis process, the concept of “locating” as the essence of the participants’ experience was extracted as follows: (A) self-exploration (exploring the changes in one's life), (B) others’ exploration (exploring the changes in the life of family members and the relationship between self and others), (C) position evaluation (self-position analysis), and (D) self-concept preservation. Conclusion: The present study has developed new understandings of mental experiences of burn patients’ self-concept by describing the concept of “self-locating”. It helps us in classifying and understanding the concepts described in comprehensive theories developed in this area. They do this by focusing on what burn patients experience for choosing self-preservation strategies and having a meaningful life. The finding can be used as a conceptual framework for palliative care program in Iran. PMID:26009672

Collisional-Radiative Modeling of Free-Burning Arc Plasma in Argon

DTIC Science & Technology

2013-06-01

temeratures of electrons and heavy particles was demonstrated. The plasma chemistry is important but yet just one element of the complex arc...description. Therefore, the present work is aimed at the analysis of the plasma chemistry in a way that the model enables a deeper look into the polulations... PLASMA CHEMISTRY The present study aims at analyzing the collisional and radiative processes in argon with a view toward application to non

New Scientific Aspects of the "Burning Candle" Experiment

ERIC Educational Resources Information Center

Massalha, Taha

2016-01-01

The "burning candle" experiment is used in middle school education programs to prove that air contains a component that is essential to burning (i.e., oxygen). The accepted interpretation taught by teachers in middle school is this: when burning occurs, oxygen is used up, creating an underpressure that causes a rise in water level inside…

Plasma kinetic effects on atomistic mix in one dimension and at structured interfaces (II)

NASA Astrophysics Data System (ADS)

Albright, Brian; Yin, Lin; Cooley, James; Haack, Jeffrey; Douglas, Melissa

2017-10-01

The Marble campaign seeks to develop a platform for studying mix evolution in turbulent, inhomogeneous, high-energy-density plasmas at the NIF. Marble capsules contain engineered CD foams, the pores of which are filled with hydrogen and tritium. During implosion, hydrodynamic stirring and plasma diffusivity mix tritium fuel into the surrounding CD plasma, leading to both DD and DT fusion neutron production. In this presentation, building upon prior work, kinetic particle-in-cell simulations using the VPIC code are used to examine kinetic effects on thermonuclear burn in Marble-like settings. Departures from Maxwellian distributions are observed near the interface and TN burn rates and inferred temperatures from synthetic neutron time of flight diagnostics are compared with those from treating the background species as Maxwellian. Work performed under the auspices of the U.S. DOE by the Los Alamos National Security, LLC Los Alamos National Laboratory and supported by the ASC and Science programs.

Evolution of space open electric arc burning in the external axial magnetic field

NASA Astrophysics Data System (ADS)

Urusova, I. R.; Urusova, T. E.

2018-06-01

The calculation was made for open DC electric arc burning in an external uniform axial magnetic field. It was performed within the framework of a nonstationary three-dimensional mathematical model in approximation of partial local thermodynamic equilibrium of plasma. A "schematic" analog of electron temperature fluctuations was proposed for numerical realization of the open electric arc column of a helical shape. According to calculations, it was established that the column of the open electric arc takes a helical space shape. Plasma rotates around a longitudinal axis of the arc, at that the directions of plasma rotation near the cathode and the anode are opposite. In the arc cross-sections, the velocity of plasma rotation is unequal and the deviation value of the same part of the arc from the central axis varies in time. A helical shape of the open arc is not stable and varies in time. Apparently, the open arc cannot remain stable and invariable in the time helical shape in the external axial magnetic field.

Glutamine granule-supplemented enteral nutrition maintains immunological function in severely burned patients.

PubMed

Peng, Xi; Yan, Hong; You, Zhongyi; Wang, Pei; Wang, Shiliang

2006-08-01

Glutamine is an important energy source for immune cells. It is a necessary nutrient for cell proliferation, and serves as specific fuel for lymphocytes, macrophages, and enterocytes when it is present in appropriate concentrations. The purpose of this clinical study was to observe the effects of enteral nutrition supplemented with glutamine granules on immunologic function in severely burned patients. Forty-eight severely burned patients (total burn surface area 30-75%, full thickness burn area 20-58%) who met the requirements of the protocol joined this double-blind randomized controlled clinical trail. Patients were randomly divided into two groups: burn control group (B group, 23 patients) and glutamine treated group (Gln group, 25 patients). There was isonitrogenous and isocaloric intake in both groups, Gln and B group patents were given glutamine granules or placebo (glycine) at 0.5 g/kgd for 14 days with oral feeding or tube feeding, respectively. The plasma level of glutamine and several indices of immunologic function including lymphocyte transformation ratio, neutrophil phagocytosis index (NPI), CD4/CD8 ratio, the content of immunoglobulin, complement C3, C4 and IL-2 levels were determined. Moreover, wound healing rate of burn area was observed and then hospital stay was recorded. The results showed significantly reduced plasma glutamine and damaged immunological function after severe burn Indices of cellular immunity function were remarkably decreased from normal controls. After taking glutamine granules for 14 days, plasma glutamine concentration was significantly higher in Gln group than that in B group (607.86+/-147.25 micromol/L versus 447.63+/-132.38 micromol/L, P<0.01). On the other hand, cellular immunity functions were improved in Gln group, such as lymphocyte transformation ratio, NPI, CD4/CD8 ratio and IL-2 compared those in the B group (P<0.05-0.01). However, for humoral immunity function such as the concentration of IgG, IgM, C3, C4, no marked changes were seen compared with the B group (P>0.05). In addition, wound healing was better and hospital stay days were reduced in Gln group (46.59+/-12.98 days versus 55.68+/-17.36 days, P<0.05). These indicated that immunological function damage is present after severe burn; supplemented glutamine granules with oral feeding or tube feeding abate the degree of immunosuppression, improve immunological function especially cellular immunity function, ameliorate wound healing and reduce hospital stay.

Modeling prescribed burning experiments and assessing the fire impacts on local to regional air quality

NASA Astrophysics Data System (ADS)

Zhou, L.; Baker, K. R.; Napelenok, S. L.; Elleman, R. A.; Urbanski, S. P.

2016-12-01

Biomass burning, including wildfires and prescribed burns, strongly impact the global carbon cycle and are of increasing concern due to the potential impacts on ambient air quality. This modelling study focuses on the evolution of carbonaceous compounds during a prescribed burning experiment and assesses the impacts of burning on local to regional air quality. The Community Multiscale Air Quality (CMAQ) model is used to conduct 4 and 2 km grid resolution simulations of prescribed burning experiments in southeast Washington state and western Idaho state in summer 2013. The ground and airborne measurements from the field experiment are used to evaluate the model performance in capturing surface and aloft impacts from the burning events. Phase partitioning of organic compounds in the plume are studied as it is a crucial step towards understanding the fate of carbonaceous compounds. The sensitivities of ambient concentrations and deposition to emissions are conducted for organic carbon, elemental carbon and ozone to estimate the impacts of fire on air quality.

Increasing Plasma Parameters using Sheared Flow Stabilization of a Z-Pinch

NASA Astrophysics Data System (ADS)

Shumlak, Uri

2016-10-01

Recent experiments on the ZaP Flow Z-Pinch at the University of Washington have been successful in compressing the plasma column to smaller radii, producing the predicted increases in plasma density (1018 cm-3), temperature (200 eV), and magnetic fields (4 T), while maintaining plasma stability for many Alfven times (over 40 μs) using sheared plasma flows. These results indicate the suitability of the device as a discovery science platform for astrophysical and high energy density plasma research, and keeps open a possible path to achieving burning plasma conditions in a compact fusion device. Long-lived Z-pinch plasmas have been produced with dimensions of 1 cm radius and 100 cm long that are stabilized by sheared axial flows for over 1000 Alfven radial transit times. The observed plasma stability is coincident with the presence of a sheared flow as measured by time-resolved multi-chord ion Doppler spectroscopy applied to impurity ion radiation. These measurements yield insights into the evolution of the velocity profile and show that the stabilizing behavior of flow shear agrees with theoretical calculations and 2-D MHD computational simulations. The flow shear value, extent, and duration are shown to be consistent with theoretical models of the plasma viscosity, which places a design constraint on the maximum axial length of a sheared flow stabilized Z-pinch. Measurements of the magnetic field topology indicate simultaneous azimuthal symmetry and axial uniformity along the entire 100 cm length of the Z-pinch plasma. Separate control of plasma acceleration and compression have increased the accessible plasma parameters and have generated stable plasmas with radii below 0.5 cm, as measured with a high resolution digital holographic interferometer. This work was supported by Grants from U.S. DOE, NNSA, and ARPA-E.

Gastrointestinal Fluid Resuscitation of Thermally Injured Patients

DTIC Science & Technology

2006-10-01

optimiza- tion of ORT solutions.44–47 Further research on oral fluids for plasma-volume expansion has been performed by NASA . Prolonged space flight is...222 (4.4) 60 44 4 28 370 Burn Jiang’s Burn Drink 252 (5.0) 48 28 0 20 347 Burn Ricelyte (3.0) 50 45 25 34 200 Dehydration AstroAde ( NASA ) 0 164 76 0 40...hemorrhagic shock from gastritis during a trek in Nepal. One liter of double-strength solution followed by 2 liters of standard-strength so- lution were

CHARACTERIZATION OF PARTICULATE MATTER EMISSION FROM OPEN BURNING OF RICE STRAW

PubMed Central

Oanh, Nguyen Thi Kim; Bich, Thuy Ly; Tipayarom, Danutawat; Manadhar, Bhai R.; Prapat, Pongkiatkul; Simpson, Christopher D.; Liu, L-J Sally

2010-01-01

Emission from field burning of crop residue, a common practice in many parts of the world today, has potential effects on air quality, atmosphere and climate. This study provides a comprehensive size and compositional characterization of particulate matter (PM) emission from rice straw (RS) burning using both in situ experiments (11 spread field burning) and laboratory hood experiments (3 pile and 6 spread burning) that were conducted during 2003–2006 in Thailand. The carbon balance and emission ratio method was used to determine PM emission factors (EF) in the field experiments. The obtained EFs varied from field to hood experiments reflecting multiple factors affecting combustion and emission. In the hood experiments, EFs were found to be depending on the burning types (spread or pile), moisture content and the combustion efficiency. In addition, in the field experiments, burning rate and EF were also influenced by weather conditions, i.e. wind. Hood pile burning produced significantly higher EF (20±8 g kg−1 RS) than hood spread burning (4.7±2.2 g kg−1 RS). The majority of PM emitted from the field burning was PM2.5 with EF of 5.1±0.7 g m−2 or 8.3±2.7 g kg−1 RS burned. The coarse PM fraction (PM10-2.5) was mainly generated by fire attention activities and was relatively small, hence the resulting EF of PM10 (9.4±3.5 g kg−1 RS) was not significantly higher than PM2.5. PM size distribution was measured across 8 size ranges (from <0.4 μm to >9.0 μm). The largest fractions of PM, EC and OC were associated with PM1.1. The most significant components in PM2.5 and PM10 include OC, water soluble ions and levoglucosan. Relative abundance of some methoxyphenols (e.g., acetylsyringone), PAHs (e.g., fluoranthene and pyrene), organochlorine pesticides and PCBs may also serve as additional signatures for the PM emission. Presence of these toxic compounds in PM of burning smoke increases the potential toxic effects of the emission. For illustration, an estimation of the annual RS field burning in Thailand was made using the obtained in situ field burning EFs and preliminary burning activity data. PMID:21243095

Control of External Kink Instability

NASA Astrophysics Data System (ADS)

Navratil, Gerald

2004-11-01

A fundamental pressure and current limiting phenomenon in magnetically confined plasmas for fusion energy is the long wavelength ideal-MHD kink mode. These modes have been extensively studied in tokamak and reversed field pinch (RFP) devices. They are characterized by significant amplitude on the boundary of the confined plasma and can therefore be controlled by manipulation of the external boundary conditions. In the past ten years, the theoretically predicted stabilizing effect of a nearby conducting wall has been documented in experiments, which opens the possibility of a significant increase in maximum stable plasma pressure. While these modes are predicted to remain unstable when the stabilizing wall is resistive, their growth rates are greatly reduced from the hydrodynamic time scale to the time scale of magnetic diffusion through the resistive wall. These resistive wall slowed kink modes have been identified as limiting phenomena in tokamak (DIII-D, PBX-M, HBT-EP, JT-60U, JET, NSTX) and RFP (HBTX, Extrap, T2R) devices. The theoretical prediction of stabilization to nearly the ideal wall pressure limit by toroidal plasma rotation and/or active feedback control using coils has recently been realized experimentally. Sustained, stable operation at double the no-wall pressure limit has been achieved. Discovery of the phenomenon of resonant field amplification by marginally stable kink modes and its role in the momentum balance of rotationally stabilized plasmas has emerged as a key feature. A theoretical framework, based on an extension of the very successful treatment of the n=0 axisymmetric mode developed in the early 1990's, to understand the stabilization mechanisms and model the performance of active feedback control systems is now established. This allows design of kink control systems for burning plasma experiments like ITER.

Porcine intact and wounded skin responses to atmospheric nonthermal plasma.

PubMed

Wu, Andrew S; Kalghatgi, Sameer; Dobrynin, Danil; Sensenig, Rachel; Cerchar, Ekaternia; Podolsky, Erica; Dulaimi, Essel; Paff, Michelle; Wasko, Kimberly; Arjunan, Krishna Priya; Garcia, Kristin; Fridman, Gregory; Balasubramanian, Manjula; Ownbey, Robert; Barbee, Kenneth A; Fridman, Alexander; Friedman, Gary; Joshi, Suresh G; Brooks, Ari D

2013-01-01

Thermal plasma is a valued tool in surgery for its coagulative and ablative properties. We suggested through in vitro studies that nonthermal plasma can sterilize tissues, inactive pathogens, promote coagulation, and potentiate wound healing. The present research was undertaken to study acute toxicity in porcine skin tissues. We demonstrate that floating electrode-discharge barrier discharge (FE-DBD) nonthermal plasma is electrically safe to apply to living organisms for short periods. We investigated the effects of FE-DBD plasma on Yorkshire pigs on intact and wounded skin immediately after treatment or 24h posttreatment. Macroscopic or microscopic histological changes were identified using histological and immunohistochemical techniques. The changes were classified into four groups for intact skin: normal features, minimal changes or congestive changes, epidermal layer damage, and full burn and into three groups for wounded skin: normal, clot or scab, and full burn-like features. Immunohistochemical staining for laminin layer integrity showed compromise over time. A marker for double-stranded DNA breaks, γ-H2AX, increased over plasma-exposure time. These findings identified a threshold for plasma exposure of up to 900s at low power and <120s at high power. Nonthermal FE-DBD plasma can be considered safe for future studies of external use under these threshold conditions for evaluation of sterilization, coagulation, and wound healing. Copyright © 2013 Elsevier Inc. All rights reserved.

Optimization of High Porosity Thermal Barrier Coatings Generated with a Porosity Former

NASA Astrophysics Data System (ADS)

Medřický, Jan; Curry, Nicholas; Pala, Zdenek; Vilemova, Monika; Chraska, Tomas; Johansson, Jimmy; Markocsan, Nicolaie

2015-04-01

Yttria-stabilized zirconia thermal barrier coatings are extensively used in turbine industry; however, increasing performance requirements have begun to make conventional air plasma sprayed coatings insufficient for future needs. Since the thermal conductivity of bulk material cannot be lowered easily; the design of highly porous coatings may be the most efficient way to achieve coatings with low thermal conductivity. Thus the approach of fabrication of coatings with a high porosity level based on plasma spraying of ceramic particles of dysprosia-stabilized zirconia mixed with polymer particles, has been tested. Both polymer and ceramic particles melt in plasma and after impact onto a substrate they form a coating. When the coating is subjected to heat treatment, polymer burns out and a complex structure of pores and cracks is formed. In order to obtain desired porosity level and microstructural features in coatings; a design of experiments, based on changes in spray distance, powder feeding rate, and plasma-forming atmosphere, was performed. Acquired coatings were evaluated for thermal conductivity and thermo-cyclic fatigue, and their morphology was assessed using scanning electron microscopy. It was shown that porosity level can be controlled by appropriate changes in spraying parameters.

Fast soft x-ray images of magnetohydrodynamic phenomena in NSTX.

PubMed

Bush, C E; Stratton, B C; Robinson, J; Zakharov, L E; Fredrickson, E D; Stutman, D; Tritz, K

2008-10-01

A variety of magnetohydrodynamic (MHD) phenomena have been observed on NSTX. Many of these affect fast particle losses, which are of major concern for future burning plasma experiments. Usual diagnostics for studying these phenomena are arrays of Mirnov coils for magnetic oscillations and p-i-n diode arrays for soft x-ray emission from the plasma core. Data reported here are from a unique fast soft x-ray imaging camera (FSXIC) with a wide-angle (pinhole) tangential view of the entire plasma minor cross section. The camera provides a 64x64 pixel image, on a charge coupled device chip, of light resulting from conversion of soft x rays incident on a phosphor to the visible. We have acquired plasma images at frame rates of 1-500 kHz (300 frames/shot) and have observed a variety of MHD phenomena: disruptions, sawteeth, fishbones, tearing modes, and edge localized modes (ELMs). New data including modes with frequency >90 kHz are also presented. Data analysis and modeling techniques used to interpret the FSXIC data are described and compared, and FSXIC results are compared to Mirnov and p-i-n diode array results.

High Voltage, Fast-Switching Module for Active Control of Magnetic Fields and Edge Plasma Currents

NASA Astrophysics Data System (ADS)

Ziemba, Timothy; Miller, Kenneth; Prager, James; Slobodov, Ilia

2016-10-01

Fast, reliable, real-time control of plasma is critical to the success of magnetic fusion science. High voltage and current supplies are needed to mitigate instabilities in all experiments as well as disruption events in large scale tokamaks for steady-state operation. Silicon carbide (SiC) MOSFETs offer many advantages over IGBTs including lower drive energy requirements, lower conduction and switching losses, and higher switching frequency capabilities; however, these devices are limited to 1.2-1.7 kV devices. As fusion enters the long-pulse and burning plasma eras, efficiency of power switching will be important. Eagle Harbor Technologies (EHT), Inc. developing a high voltage SiC MOSFET module that operates at 10 kV. This switch module utilizes EHT gate drive technology, which has demonstrated the ability to increase SiC MOSFET switching efficiency. The module will allow more rapid development of high voltage switching power supplies at lower cost necessary for the next generation of fast plasma feedback and control. EHT is partnering with the High Beta Tokamak group at Columbia to develop detailed high voltage module specifications, to ensure that the final product meets the needs of the fusion science community.

Damping Rates of Energetic Particle Modes and Stability With Changing Equilibrium Conditions in the MST Reversed-Field Pinch

NASA Astrophysics Data System (ADS)

Sears, S. H.; Almagri, A. F.; Anderson, J. K.; Bonofiglo, P. J.; Capecchi, W.; Kim, J.

2016-10-01

The damping of Alfvenic waves is an important process, with implications varying from anomalous ion heating in laboratory and astrophysical plasmas to the stability of fusion alpha-driven modes in a burning plasma. With a 1 MW NBI on the MST, a controllable set of energetic particle modes (EPMs) and Alfvenic eigenmodes can be excited. We investigate the damping of these modes as a function of both magnetic and flow shear. Typical EPM damping rates are -104 s-1 in standard RFP discharges. Magnetic shear in the region of large energetic ion density is -2 cm-1 and can be increased up to -2.5 cm-1 by varying the boundary field. Continuum mode damping rates can be reduced up to 50%. New experiments use a bias probe to control the rotation profile. Accelerating the edge plasma relative to the rapidly rotating NBI-driven core decreases the flow shear, while decelerating the edge plasma increases the flow shear in the region of strong energetic ion population. Mode damping rates measured as a function of the local flow shear are compared to ideal MHD predictions. Work supported by US DOE.

High-density carbon ablator ignition path with low-density gas-filled rugby hohlraum

NASA Astrophysics Data System (ADS)

Amendt, Peter; Ho, Darwin D.; Jones, Ogden S.

2015-04-01

A recent low gas-fill density (0.6 mg/cc 4He) cylindrical hohlraum experiment on the National Ignition Facility has shown high laser-coupling efficiency (>96%), reduced phenomenological laser drive corrections, and improved high-density carbon capsule implosion symmetry [Jones et al., Bull. Am. Phys. Soc. 59(15), 66 (2014)]. In this Letter, an ignition design using a large rugby-shaped hohlraum [Amendt et al., Phys. Plasmas 21, 112703 (2014)] for high energetics efficiency and symmetry control with the same low gas-fill density (0.6 mg/cc 4He) is developed as a potentially robust platform for demonstrating thermonuclear burn. The companion high-density carbon capsule for this hohlraum design is driven by an adiabat-shaped [Betti et al., Phys. Plasmas 9, 2277 (2002)] 4-shock drive profile for robust high gain (>10) 1-D ignition performance and large margin to 2-D perturbation growth.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKenzie-Carter, M.A.; Lyon, R.E.; Rope, S.K.

This report contains information to support the Environmental Assessment for the Burning Plasma Experiment (BPX) Project proposed for the Princeton Plasma Physics Laboratory (PPPL). The assumptions and methodology used to assess the impact to members of the public from operational and accidental releases of radioactive material from the proposed BPX during the operational period of the project are described. A description of the tracer release tests conducted at PPPL by NOAA is included; dispersion values from these tests are used in the dose calculations. Radiological releases, doses, and resulting health risks are calculated and summarized. The computer code AIRDOS- EPA,more » which is part of the computer code system CAP-88, is used to calculate the individual and population doses for routine releases; FUSCRAC3 is used to calculate doses resulting from off-normal releases where direct application of the NOAA tracer test data is not practical. Where applicable, doses are compared to regulatory limits and guideline values. 48 refs., 16 tabs.« less

Temporal Cytokine Profiles in Severely Burned Patients: A Comparison of Adults and Children

PubMed Central

Finnerty, Celeste C; Jeschke, Marc G; Herndon, David N; Gamelli, Richard; Gibran, Nicole; Klein, Matthew; Silver, Geoff; Arnoldo, Brett; Remick, Daniel; Tompkins, Ronald G

2008-01-01

A severe burn leads to hypermetabolism and catabolism resulting in compromised function and structural changes of essential organs. The release of cytokines has been implicated in this hypermetabolic response. The severity of the hypermetabolic response following burn injury increases with age, as does the mortality rate. Due to the relationship between the hypermetabolic and inflammatory responses, we sought to compare the plasma cytokine profiles following a severe burn in adults and in children. We enrolled 25 adults and 24 children who survived a flame burn covering more than 20% of total body surface area (TBSA). The concentrations of 22 cytokines were measured using the Linco multiplex array system (St. Charles, MO, USA). Large perturbations in the expression of pro- and anti-inflammatory cytokines were seen following thermal injury. During the first week following burn injury, IFN-γ, IL-10, IL-17, IL-4, IL-6, and IL-8 were detected at significantly higher levels in adults compared with children, P < 0.05. Significant differences were measured during the second week post-burn for IL-1β (higher in children) and IL-5 (higher in adults), P < 0.05. IL-18 was more abundant in children compared with adults during the third week post-burn, P < 0.05. Between post-burn d 21 and d 66, IL-1α was detected at higher concentrations in pediatric compared with adult patients, P < 0.05. Only GM-CSF expression was significantly different at all time points; it was detected at lower levels in pediatric patients, P < 0.05. Eotaxin, G-CSF, IL-13, IL-15, IP-10, MCP-1, and MIP-1α were detected at significantly different concentrations in adult compared with pediatric patients at multiple time points, P < 0.05. There were no differences in IL-12, IL-2, IL-7, or TNF levels in adult compared with pediatric burn patients at any of these time points. Following severe flame burns, the cytokine profiles in pediatric patients differ compared with those in adult patients, which may provide insight with respect to the higher morbidity rate in adults. Furthermore, the dramatic discrepancies observed in plasma cytokine detection between children and adults suggest that these two patient populations may benefit from different therapeutic interventions to achieve attenuation of the post-burn inflammatory response. PMID:18548133

Plasma-Jet Magneto-Inertial Fusion Burn Calculations

NASA Astrophysics Data System (ADS)

Santarius, John

2010-11-01

Several issues exist related to using plasma jets to implode a Magneto-Inertial Fusion (MIF) liner onto a magnetized plasmoid and compress it to fusion-relevant temperatures [1]. The poster will explore how well the liner's inertia provides transient plasma confinement and affects the burn dynamics. The investigation uses the University of Wisconsin's 1-D Lagrangian radiation-hydrodynamics code, BUCKY, which solves single-fluid equations of motion with ion-electron interactions, PdV work, table-lookup equations of state, fast-ion energy deposition, pressure contributions from all species, and one or two temperatures. Extensions to the code include magnetic field evolution as the plasmoid compresses plus dependence of the thermal conductivity on the magnetic field. [4pt] [1] Y.C. F. Thio, et al.,``Magnetized Target Fusion in a Spheroidal Geometry with Standoff Drivers,'' in Current Trends in International Fusion Research, E. Panarella, ed. (National Research Council of Canada, Ottawa, Canada, 1999), p. 113.

Assessment of ion kinetic effects in shock-driven inertial confinement fusion implosions using fusion burn imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, M. J., E-mail: mros@lle.rochester.edu; Séguin, F. H.; Rinderknecht, H. G.

The significance and nature of ion kinetic effects in D{sup 3}He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, N{sub K}) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatiallymore » resolved measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (N{sub K} ∼ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects.« less

Assessment of ion kinetic effects in shock-driven inertial confinement fusion (ICF) implosions using fusion burn imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenberg, M. J.; Séguin, F. H.; Amendt, P. A.

The significance and nature of ion kinetic effects in D³He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, N K) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatially resolvedmore » measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (N K ~ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects.« less

Assessment of ion kinetic effects in shock-driven inertial confinement fusion implosions using fusion burn imaging

NASA Astrophysics Data System (ADS)

Rosenberg, M. J.; Séguin, F. H.; Amendt, P. A.; Atzeni, S.; Rinderknecht, H. G.; Hoffman, N. M.; Zylstra, A. B.; Li, C. K.; Sio, H.; Gatu Johnson, M.; Frenje, J. A.; Petrasso, R. D.; Glebov, V. Yu.; Stoeckl, C.; Seka, W.; Marshall, F. J.; Delettrez, J. A.; Sangster, T. C.; Betti, R.; Wilks, S. C.; Pino, J.; Kagan, G.; Molvig, K.; Nikroo, A.

2015-06-01

The significance and nature of ion kinetic effects in D3He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, NK) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatially resolved measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (NK ˜ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects.

Assessment of ion kinetic effects in shock-driven inertial confinement fusion (ICF) implosions using fusion burn imaging

DOE PAGES

Rosenberg, M. J.; Séguin, F. H.; Amendt, P. A.; ...

2015-06-02

The significance and nature of ion kinetic effects in D³He-filled, shock-driven inertial confinement fusion implosions are assessed through measurements of fusion burn profiles. Over this series of experiments, the ratio of ion-ion mean free path to minimum shell radius (the Knudsen number, N K) was varied from 0.3 to 9 in order to probe hydrodynamic-like to strongly kinetic plasma conditions; as the Knudsen number increased, hydrodynamic models increasingly failed to match measured yields, while an empirically-tuned, first-step model of ion kinetic effects better captured the observed yield trends [Rosenberg et al., Phys. Rev. Lett. 112, 185001 (2014)]. Here, spatially resolvedmore » measurements of the fusion burn are used to examine kinetic ion transport effects in greater detail, adding an additional dimension of understanding that goes beyond zero-dimensional integrated quantities to one-dimensional profiles. In agreement with the previous findings, a comparison of measured and simulated burn profiles shows that models including ion transport effects are able to better match the experimental results. In implosions characterized by large Knudsen numbers (N K ~ 3), the fusion burn profiles predicted by hydrodynamics simulations that exclude ion mean free path effects are peaked far from the origin, in stark disagreement with the experimentally observed profiles, which are centrally peaked. In contrast, a hydrodynamics simulation that includes a model of ion diffusion is able to qualitatively match the measured profile shapes. Therefore, ion diffusion or diffusion-like processes are identified as a plausible explanation of the observed trends, though further refinement of the models is needed for a more complete and quantitative understanding of ion kinetic effects.« less

Shapes of Spectral Lines of Nonuniform Plasma of Electric Arc Discharge Between Copper Electrodes

NASA Astrophysics Data System (ADS)

Babich, Ida L.; Boretskij, Viacheslav F.; Veklich, Anatoly N.

2007-09-01

The radial profiles of the temperature and electron density in the plasma of the free burning electric arc between copper electrodes are studied by optical spectroscopy techniques. The electron density and the temperature in plasma as initial parameters were used in the calculation of the plasma composition in local thermodynamic equilibrium (LTE) assumption. We used the Saha's equation for copper, nitrogen and oxygen, dissociation equation for nitrogen and oxygen, the equation of plasma electrical neutrality and Dalton's law as well. So, it would be possible to determine the amounts of metal vapours in plasma.

[Clinical evaluation of the postburn retention and the metabolism of Imipenem in the third space].

PubMed

Rong, Xin-Zhou; Bei, Chun-Hua; Huang, Xiao-Hua; Li, Qing-Hui

2003-04-01

To explore the half life and retention of Imipenem in the third space. Eight severely burned patients and eight healthy volunteers were enrolled as the burn group (B) and normal control group (C), respectively. HPLC (high performance liquid chromatography) was employed to determine the contents of Imipenem in the plasma, subeschar tissue fluid (STF) and the changes in its pharmacokinetics. Furthermore, the Imipenem content in the third space was calculated according to the systemic edema degree. The half life of Imipenem in STF (2.53 h) was longer than that in plasma (1.73 h), P < 0.05). The Imipenem content in STF increased gradually along with the lapse of time after repeated intravenous infusion of Imipenem, and at the same the total content of imipenem was increased significantly in the third space. There was antibiotic retention in the third space after severe burn injury, and a prolonged action of the drug could be expected when the drug re-entered the blood stream.

High-resolution spectroscopy for Doppler-broadening ion temperature measurements of implosions at the National Ignition Facility.

PubMed

Koch, J A; Stewart, R E; Beiersdorfer, P; Shepherd, R; Schneider, M B; Miles, A R; Scott, H A; Smalyuk, V A; Hsing, W W

2012-10-01

Future implosion experiments at the national ignition facility (NIF) will endeavor to simultaneously measure electron and ion temperatures with temporal and spatial resolution in order to explore non-equilibrium temperature distributions and their relaxation toward equilibrium. In anticipation of these experiments, and with understanding of the constraints of the NIF facility environment, we have explored the use of Doppler broadening of mid-Z dopant emission lines, such as krypton He-α at 13 keV, as a diagnostic of time- and potentially space-resolved ion temperature. We have investigated a number of options analytically and with numerical raytracing, and we have identified several promising candidate spectrometer designs that meet the expected requirements of spectral and temporal resolution and data signal-to-noise ratio for gas-filled exploding pusher implosions, while providing maximum flexibility for use on a variety of experiments that potentially include burning plasma.

Thermonuclear reactions probed at stellar-core conditions with laser-based inertial-confinement fusion

DOE PAGES

Casey, D. T.; Sayre, D. B.; Brune, C. R.; ...

2017-08-07

Stars are giant thermonuclear plasma furnaces that slowly fuse the lighter elements in the universe into heavier elements, releasing energy, and generating the pressure required to prevent collapse. To understand stars, we must rely on nuclear reaction rate data obtained, up to now, under conditions very different from those of stellar cores. Here we show thermonuclear measurements of the 2H(d, n) 3He and 3H(t,2n) 4He S-factors at a range of densities (1.2–16 g cm –3) and temperatures (2.1–5.4 keV) that allow us to test the conditions of the hydrogen-burning phase of main-sequence stars. The relevant conditions are created using inertial-confinementmore » fusion implosions at the National Ignition Facility. Here, our data agree within uncertainty with previous accelerator-based measurements and establish this approach for future experiments to measure other reactions and to test plasma-nuclear effects present in stellar interiors, such as plasma electron screening, directly in the environments where they occur.« less

PREFACE: Progress in the ITER Physics Basis

NASA Astrophysics Data System (ADS)

Ikeda, K.

2007-06-01

I would firstly like to congratulate all who have contributed to the preparation of the `Progress in the ITER Physics Basis' (PIPB) on its publication and express my deep appreciation of the hard work and commitment of the many scientists involved. With the signing of the ITER Joint Implementing Agreement in November 2006, the ITER Members have now established the framework for construction of the project, and the ITER Organization has begun work at Cadarache. The review of recent progress in the physics basis for burning plasma experiments encompassed by the PIPB will be a valuable resource for the project and, in particular, for the current Design Review. The ITER design has been derived from a physics basis developed through experimental, modelling and theoretical work on the properties of tokamak plasmas and, in particular, on studies of burning plasma physics. The `ITER Physics Basis' (IPB), published in 1999, has been the reference for the projection methodologies for the design of ITER, but the IPB also highlighted several key issues which needed to be resolved to provide a robust basis for ITER operation. In the intervening period scientists of the ITER Participant Teams have addressed these issues intensively. The International Tokamak Physics Activity (ITPA) has provided an excellent forum for scientists involved in these studies, focusing their work on the high priority physics issues for ITER. Significant progress has been made in many of the issues identified in the IPB and this progress is discussed in depth in the PIPB. In this respect, the publication of the PIPB symbolizes the strong interest and enthusiasm of the plasma physics community for the success of the ITER project, which we all recognize as one of the great scientific challenges of the 21st century. I wish to emphasize my appreciation of the work of the ITPA Coordinating Committee members, who are listed below. Their support and encouragement for the preparation of the PIPB were fundamental to its completion. I am pleased to witness the extensive collaborations, the excellent working relationships and the free exchange of views that have been developed among scientists working on magnetic fusion, and I would particularly like to acknowledge the importance which they assign to ITER in their research. This close collaboration and the spirit of free discussion will be essential to the success of ITER. Finally, the PIPB identifies issues which remain in the projection of burning plasma performance to the ITER scale and in the control of burning plasmas. Continued R&D is therefore called for to reduce the uncertainties associated with these issues and to ensure the efficient operation and exploitation of ITER. It is important that the international fusion community maintains a high level of collaboration in the future to address these issues and to prepare the physics basis for ITER operation. ITPA Coordination Committee R. Stambaugh (Chair of ITPA CC, General Atomics, USA) D.J. Campbell (Previous Chair of ITPA CC, European Fusion Development Agreement—Close Support Unit, ITER Organization) M. Shimada (Co-Chair of ITPA CC, ITER Organization) R. Aymar (ITER International Team, CERN) V. Chuyanov (ITER Organization) J.H. Han (Korea Basic Science Institute, Korea) Y. Huo (Zengzhou University, China) Y.S. Hwang (Seoul National University, Korea) N. Ivanov (Kurchatov Institute, Russia) Y. Kamada (Japan Atomic Energy Agency, Naka, Japan) P.K. Kaw (Institute for Plasma Research, India) S. Konovalov (Kurchatov Institute, Russia) M. Kwon (National Fusion Research Center, Korea) J. Li (Academy of Science, Institute of Plasma Physics, China) S. Mirnov (TRINITI, Russia) Y. Nakamura (National Institute for Fusion Studies, Japan) H. Ninomiya (Japan Atomic Energy Agency, Naka, Japan) E. Oktay (Department of Energy, USA) J. Pamela (European Fusion Development Agreement—Close Support Unit) C. Pan (Southwestern Institute of Physics, China) F. Romanelli (Ente per le Nuove tecnologie, l'Energia e l'Ambiente, Italy and European Fusion Development Agreement—Close Support Unit) N. Sauthoff (Princeton Plasma Physics Laboratory, USA and Oak Ridge National Laboratories, USA) Y. Saxena (Institute for Plasma Research, India) Y. Shimomura (ITER Organization) R. Singh (Institute for Plasma Research, India) S. Takamura (Nagoya University, Japan) K. Toi (National Institute for Fusion Studies, Japan) M. Wakatani (Kyoto University, Japan (deceased)) H. Zohm (Max-Planck-Institut für Plasmaphysik, Garching, Germany)

[Experimental determination of the time-dependent extent of after-burning with reference to possibilities of the plastic surgery reconstruction of 3d degree burns].

PubMed

Bäumer, F; Henrich, H A; Ussmüller, J

1986-02-01

The present experiments try to answer the question as to the time-dependent extent of the after-burning process after full-thickness burn (third degree). For an early plastic surgical treatment it was of interest to determine the most early time of escharotomy. The time-dependent spreading of the after-burning area reached its maximum five days after the burn injury. The after-burning area was marked by intravenous injections of Patentblau which caused distinct intravital colouring. Subsequently no further progress could be observed. In the present experiments we suggest this time as the earliest time for plastic covering in case it would be dependent upon the end of the after-burning process.

Prediction and realization of ITER-like pedestal pressure in the high- B tokamak Alcator C-Mod

NASA Astrophysics Data System (ADS)

Hughes, Jerry

2017-10-01

Fusion power in a burning plasma will scale as the square of the plasma pressure, which is increased in a straightforward way by increasing magnetic field: Pfus p2 B4 . Experiments on Alcator C-Mod, a compact high- B tokamak, have tested predictive capability for pedestal pressure, at toroidal field BT up to 8T , and poloidal field BP up to 1T . These reactor-like fields enable C-Mod to approach an ITER predicted value of 90kPa . This is expected if, as in the EPED model, the pedestal is constrained by onset of kinetic ballooning modes (KBMs) and peeling-ballooning modes (PMB), yielding a pressure pedestal approximately as pped BT ×BP . One successful path to high confinement on C-Mod is the high-density (ne > 3 ×1020m-3) approach, pursued using enhanced D-alpha (EDAs) H-mode. In EDA H-mode, transport regulates both the pedestal profiles and the core impurity content, holding the pedestal stationary, at just below the PBM stability boundary. We have extended this stationary ELM-suppressed regime to the highest magnetic fields achievable on C-Mod, and used it to approach the maximum pedestal predicted by EPED at high density: pped 60kPa . Another approach to high pressure utilizes a pedestal limited by PBMs at low collisionality, where pressure increases with density and EPED predicts access to a higher ``Super H'' solution for pped. Experiments at reduced density (ne < 2 ×1020m-3) and strong plasma shaping (δ > 0.5) accessed these regimes on C-Mod, producing pedestals with world record pped 80kPa , at Tped 2keV . In both the high and low density approaches, the impact of the pedestal on core performance is substantial. Our exploration of high pedestal regimes yielded a volume-averaged pressure 〈 p 〉 > 2atm , a world record value for a magnetic fusion device. The results hold promise for the projection of pedestal pressure and overall performance of high field burning plasma devices. Supported by U.S. Department of Energy awards DE-FC02-99ER54512, DE-FG02-95ER54309, DE-FC02-06ER54873, DE-AC02-09CH11466, DE-SC0007880 using Alcator C-Mod, a DOE Office of Science User Facility.

Tridimensional Thermonuclear Instability in Subignited Plasmas and on the Surface of the Pulsars

NASA Astrophysics Data System (ADS)

Cardinali, A.; Coppi, B.

2017-10-01

Tridimensional modes involving an increase of the electron temperature can be excited as a result of alpha-particle heating in subignited D-T fusion burning plasmas when a nearly time- independent external source of heating is applied. The analyzed modes are shown to emerge from an axisymmetric toroidal configurations and are radially localized around rational magnetic surfaces corresponding to q(r =r0) =m0 /n0 where m0 and n0 are the relevant poloidal and toroidal mode numbers. The radial width of the mode is of the order of the thermal scale distance. The mode has a rather severe damping rate, that has to be overcome by the relevant heating rate. Thus the temperature range to be considered is that where the D-T plasma reactivity undergoes a relatively large increase as a function of temperature. This kind of theory has been applied to the plasmas that are envisioned to be associated with surface of pulsar and be subjects to (spatially) inhomogenous thermonuclear burning. Sponsored in part by the U.S. DoE.

A novel perspective for burn-induced myopathy: Membrane repair defect

PubMed Central

Wang, Chao; Wang, Hongyu; Wu, Dan; Hu, Jianhong; Wu, Wei; Zhang, Yong; Peng, Xi

2016-01-01

Myopathy is a common complication of severe burn patients. One potential cause of this myopathy could be failure of the plasma membrane to undergo repair following injuries generated from toxin or exercise. The aim of this study is to assess systemic effect on muscle membrane repair deficiency in burn injury. Skeletal muscle fibers isolated from burn-injured mice were damaged with a UV laser and dye influx imaged confocally to evaluate membrane repair capacity. Membrane repair failure was also tested in burn-injured mice subjected to myotoxin or treadmill exercise. We further used C2C12 myotubules and animal models to investigate the role of MG53 in development of burn-induced membrane repair defect. We demonstrated that skeletal muscle myofibers in burn-injured mice showed significantly more dye uptake after laser damage than controls, indicating a membrane repair deficiency. Myotoxin or treadmill exercise also resulted in a higher-grade repair defect in burn-injured mice. Furthermore, we observed that burn injury induced a significant decrease in MG53 levels and its dimerization in skeletal muscles. Our findings highlight a new mechanism that implicates membrane repair failure as an underlying cause of burn-induced myopathy. And, the disorders in MG53 expression and MG53 dimerization are involved in this cellular pathology. PMID:27545095

Enabling High Fidelity Measurements of Energy and Pitch Angle for Escaping Energetic Ions with a Fast Ion Loss Detector

NASA Astrophysics Data System (ADS)

Chaban, R.; Pace, D. C.; Marcy, G. R.; Taussig, D.

2016-10-01

Energetic ion losses must be minimized in burning plasmas to maintain fusion power, and existing tokamaks provide access to energetic ion parameter regimes that are relevant to burning machines. A new Fast Ion Loss Detector (FILD) probe on the DIII-D tokamak has been optimized to resolve beam ion losses across a range of 30 - 90 keV in energy and 40° to 80° in pitch angle, thereby providing valuable measurements during many different experiments. The FILD is a magnetic spectrometer; once inserted into the tokamak, the magnetic field allows energetic ions to pass through a collimating aperture and strike a scintillator plate that is imaged by a wide view camera and narrow view photomultiplier tubes (PMTs). The design involves calculating scintillator strike patterns while varying probe geometry. Calculated scintillator patterns are then used to design an optical system that allows adjustment of the focus regions for the 1 MS/s resolved PMTs. A synthetic diagnostic will be used to determine the energy and pitch angle resolution that can be attained in DIII-D experiments. Work supported in part by US DOE under the Science Undergraduate Laboratory Internship (SULI) program and under DE-FC02-04ER54698.

Joint DIII-D/EAST research on the development of a high poloidal beta scenario for the steady state missions of ITER and CFETR

NASA Astrophysics Data System (ADS)

Garofalo, A. M.; Gong, X. Z.; Ding, S. Y.; Huang, J.; McClenaghan, J.; Pan, C. K.; Qian, J.; Ren, Q. L.; Staebler, G. M.; Chen, J.; Cui, L.; Grierson, B. A.; Hanson, J. M.; Holcomb, C. T.; Jian, X.; Li, G.; Li, M.; Pankin, A. Y.; Peysson, Y.; Zhai, X.; Bonoli, P.; Brower, D.; Ding, W. X.; Ferron, J. R.; Guo, W.; Lao, L. L.; Li, K.; Liu, H.; Lyv, B.; Xu, G.; Zang, Q.

2018-01-01

Experimental and modeling investigations on the DIII-D and EAST tokamaks show the attractive transport and stability properties of fully noninductive, high poloidal-beta (β P ) plasmas, and their suitability for steady-state operating scenarios in ITER and CFETR. A key feature of the high-β P regime is the large-radius (ρ > 0.6) internal transport barrier (ITB), often observed in all channels (ne, Te, Ti, rotation), and responsible for both excellent energy confinement quality and excellent stability properties. Experiments on DIII-D have shown that, with a large-radius ITB, very high β N and β P values (both ≥ 4) can be reached by taking advantage of the stabilizing effect of a nearby conducting wall. Synergistically, higher plasma pressure provides turbulence suppression by Shafranov shift, leading to ITB sustainment independent of the plasma rotation. Experiments on EAST have been used to assess the long pulse potential of the high-β P regime. Using RF-only heating and current drive, EAST achieved minute-long fully noninductive steady state H-mode operation with strike points on an ITER-like tungsten divertor. Improved confinement (relative to standard H-mode) and steady state ITB features are observed with a monotonic q-profile with q min ˜ 1.5. Separately, experiments have shown that increasing the density in plasmas driven by lower hybrid wave broadens the q-profile, a technique that could enable a large radius ITB. These experimental results have been used to validate MHD, current drive, and turbulent transport models, and to project the high-β P regime to a burning plasma. These projections suggest the Shafranov shift alone will not suffice to provide improved confinement (over standard H-mode) without rotation and rotation shear. However, increasing the negative magnetic shear (higher q on axis) provides a similar turbulence suppression mechanism to Shafranov shift, and can help devices such as ITER and CFETR achieve their steady-state fusion goals.

Investigation of burn effect on skin using simultaneous Raman-Brillouin spectroscopy, and fluorescence microspectroscopy

NASA Astrophysics Data System (ADS)

Coker, Zachary; Meng, Zhaokai; Troyanova-Wood, Maria; Traverso, Andrew; Ballmann, Charles; Petrov, Georgi; Ibey, Bennett L.; Yakovlev, Vladislav

2017-02-01

Burns are thermal injuries that can completely damage or at least compromise the protective function of skin, and affect the ability of tissues to manage moisture. Burn-damaged tissues exhibit lower elasticity than healthy tissues, due to significantly reduced water concentrations and plasma retention. Current methods for determining burn intensity are limited to visual inspection, and potential hospital x-ray examination. We present a unique confocal microscope capable of measuring Raman and Brillouin spectra simultaneously, with concurrent fluorescence investigation from a single spatial location, and demonstrate application by investigating and characterizing the properties of burn-afflicted tissue on chicken skin model. Raman and Brillouin scattering offer complementary information about a material's chemical and mechanical structure, while fluorescence can serve as a useful diagnostic indicator and imaging tool. The developed instrument has the potential for very diverse analytical applications in basic biomedical science and biomedical diagnostics and imaging.

Scale-up considerations for surface collecting agent assisted in-situ burn crude oil spill response experiments in the Arctic: Laboratory to field-scale investigations.

PubMed

Bullock, Robin J; Aggarwal, Srijan; Perkins, Robert A; Schnabel, William

2017-04-01

In the event of a marine oil spill in the Arctic, government agencies, industry, and the public have a stake in the successful implementation of oil spill response. Because large spills are rare events, oil spill response techniques are often evaluated with laboratory and meso-scale experiments. The experiments must yield scalable information sufficient to understand the operability and effectiveness of a response technique under actual field conditions. Since in-situ burning augmented with surface collecting agents ("herders") is one of the few viable response options in ice infested waters, a series of oil spill response experiments were conducted in Fairbanks, Alaska, in 2014 and 2015 to evaluate the use of herders to assist in-situ burning and the role of experimental scale. This study compares burn efficiency and herder application for three experimental designs for in-situ burning of Alaska North Slope crude oil in cold, fresh waters with ∼10% ice cover. The experiments were conducted in three project-specific constructed venues with varying scales (surface areas of approximately 0.09 square meters, 9 square meters and 8100 square meters). The results from the herder assisted in-situ burn experiments performed at these three different scales showed good experimental scale correlation and no negative impact due to the presence of ice cover on burn efficiency. Experimental conclusions are predominantly associated with application of the herder material and usability for a given experiment scale to make response decisions. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Autogenous platelet-rich plasma gel with acellular xenogeneic dermal matrix for treatment of deep II degree burns].

PubMed

Hao, Tianzhi; Zhu, Jingmin; Hu, Wenbo; Zhang, Hua; Gao, Zhenhui; Wen, Xuehui; Zhou, Zhi; Lu, Gang; Liu, Jingjie; Li, Wen

2010-06-01

To investigate the effectiveness of autogenous platelet-rich plasma (PRP) gel with acellular xenogeneic dermal matrix in the treatment of deep II degree burns. From January 2007 to December 2009, 30 cases of deep II degree burns were treated. There were 19 males and 11 females with an average age of 42.5 years (range, 32-57 years). The burn area was 10% to 48% of total body surface area. The time from burn to hospitalization was 30 minutes to 8 hours. All patients were treated with tangential excision surgery, one side of the wounds were covered with autogenous PRP gel and acellular xenogeneic dermal matrix (PRP group), the other side of the wounds were covered with acellular xenogeneic dermal matrix only (control group). The healing rate, healing time, infection condition, and scar formation were observed. At 7 days after operation, the infection rate in PRP group (6.7%, 2/30) was significantly lower than that in control group (16.7%, 5/30, P < 0.05). The healing times were (18 +/- 4) days and (22 +/- 4) days respectively in PRP group and control group, showing significant difference (P < 0.05). The healing rates at 14 days and 21 days were 75% +/- 7% and 88% +/- 5% in PRP group, were 62% +/- 15% and 73% +/- 7% in control group, showing significant difference (P < 0.05). RPR group was superior to control group in elasticity, color, appearance, softness, scar formation, and healing quality. Autogenous PRP gel with acellular xenogeneic dermal matrix can accelerate the wound healing of deep II degree burns as well as alleviate the scar proliferation.

Making meaning in a burn peer support group: qualitative analysis of attendee interviews.

PubMed

Davis, Trevor; Gorgens, Kim; Shriberg, Janet; Godleski, Matthew; Meyer, Laura

2014-01-01

There is a paucity of literature on the personal experiences of burn support group members, the members' perceived benefits of group participation, and the meaning the survivors make of the support they receive. In order to provide effective psychosocial rehabilitation services and to meet the needs of burn survivors, it is important to understand the influence a support group has on its members as well as the personal experiences of those individuals who attend these groups. The purpose of this study was to explore the experiences of burn survivors in a burn survivor support group. Six self-identified burn survivors were interviewed by using a guided in-depth interview technique to explore their experiences in the support group. Key informant interviews and group observations served to triangulate the findings from the individual interviews. The experiences of the group members coalesced around four main themes: acceptance of self, perspective change, value of community, and reciprocity. The findings demonstrated the overall perceived positive impact the support group had on psychosocial recovery. For these members, the group aided the process of adjustment through the encouragement of adaptive coping strategies and the facilitation of community and relationships. Their experiences mirrored much of the literature on psychological growth from adversity. Burn survivors reported unique opportunities that allowed them to integrate their injury into their identity within an encouraging and safe environment. Using these accounts, the authors generated clinical suggestions that may encourage similar growth in other support group settings.

Formation of an optical pulsed discharge in a supersonic air flow by radiation of a repetitively pulsed CO{sub 2} laser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malov, Aleksei N; Orishich, Anatolii M

Results of optimisation of repetitively pulsed CO{sub 2}-laser generation are presented for finding physical conditions of forming stable burning of an optical pulsed discharge (OPD) in a supersonic air flow and for studying the influence of pulse parameters on the energy absorption efficiency of laser radiation in plasma. The optical discharge in a supersonic air flow was formed by radiation of a repetitively pulsed CO{sub 2} laser with mechanical Q-switching excited by a discharge with a convective cooling of the working gas. For the first time the influence of radiation pulse parameters on the ignition conditions and stable burning ofmore » the OPD in a supersonic air flow was investigated and the efficiency of laser radiation absorption in plasma was studied. The influence of the air flow velocity on stability of plasma production was investigated. It was shown that stable burning of the OPD in a supersonic flow is realised at a high pulse repetition rate where the interval between radiation pulses is shorter than the time of plasma blowing-off. Study of the instantaneous value of the absorption coefficient shows that after a breakdown in a time lapse of 100 - 150 ns, a quasi-stationary 'absorption phase' is formed with the duration of {approx}1.5 ms, which exists independently of air flow and radiation pulse repetition rate. This phase of strong absorption is, seemingly, related to evolution of the ionisation wave. (laser applications and other topics in quantum electronics)« less

Photoacoustic signal measurement for burned skins in the spectral range of 500-650 nm: experiment with rat burn models

NASA Astrophysics Data System (ADS)

Yamazaki, Mutsuo; Sato, Shunichi; Saito, Daizo; Fujita, Masanori; Okada, Yoshiaki; Kikuchi, Makoto; Ashida, Hiroshi; Obara, Minoru

2002-06-01

This paper reports the burn diagnosis that is based on the measurement of photoacoustic waves from skin, where the acoustic waves originate from the absorption of light by blood. For this purpose, a transducer composed of a ring-shaped piezoelectric film and a quartz fiber was made. An optical parametric oscillator (500 - 650 nm) was used as a light source and its output pulses were coupled to the quartz fiber. To investigate the optimum light wavelength, we conducted experiments using rat burn models. We demonstrated that the superficial dermal burn (SDB), deep dermal burn (DDB), deep burn (DB), and control (healthy skin) could be clearly differentiated based on the photoacoustic signals induced by the light of 532 - 580nm.

Studies of high-current relativistic electron beam interaction with gas and plasma in Novosibirsk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinitsky, S. L., E-mail: s.l.sinitsky@inp.nsk.su; Arzhannikov, A. V.; Novosibirsk State University, 2 Pirogova St., Novosibirsk, 630090

2016-03-25

This paper presents an overview of the studies on the interaction of a high-power relativistic electron beam (REB) with dense plasma confined in a long open magnetic trap. The main goal of this research is to achieve plasma parameters close to those required for thermonuclear fusion burning. The experimental studies were carried over the course of four decades on various devices: INAR, GOL, INAR-2, GOL-M, and GOL-3 (Budker Institute of Nuclear Physics) for a wide range of beam and plasma parameters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finley, V.L.; Wieczorek, M.A.

This report gives the results of the environmental activities and monitoring programs at the Princeton Plasma Physics Laboratory (PPPL) for CY94. The report is prepared to provide the US Department of Energy (DOE) and the public with information on the level of radioactive and nonradioactive pollutants, if any, added to the environment as a result of PPPL operations, as well as environmental initiatives, assessments, and programs that were undertaken in 1994. The objective of the Annual Site Environmental Report is to document evidence that PPPL`s environmental protection programs adequately protect the environment and the public health. The Princeton Plasma Physicsmore » Laboratory has engaged in fusion energy research since 195 1. The long-range goal of the US Magnetic Fusion Energy Research Program is to develop and demonstrate the practical application of fusion power as an alternate energy source. In 1994, PPPL had one of its two large tokamak devices in operation-the Tokamak Fusion Test Reactor (TFTR). The Princeton Beta Experiment-Modification or PBX-M completed its modifications and upgrades and resumed operation in November 1991 and operated periodically during 1992 and 1993; it did not operate in 1994 for funding reasons. In December 1993, TFTR began conducting the deuterium-tritium (D-T) experiments and set new records by producing over ten @on watts of energy in 1994. The engineering design phase of the Tokamak Physics Experiment (T?X), which replaced the cancelled Burning Plasma Experiment in 1992 as PPPL`s next machine, began in 1993 with the planned start up set for the year 2001. In December 1994, the Environmental Assessment (EA) for the TFTR Shutdown and Removal (S&R) and TPX was submitted to the regulatory agencies, and a finding of no significant impact (FONSI) was issued by DOE for these projects.« less

Stationary Flowing Liquid Lithium (SFLiLi) systems for tokamaks

NASA Astrophysics Data System (ADS)

Zakharov, Leonid; Gentile, Charles; Roquemore, Lane

2013-10-01

The present approach to magnetic fusion which relies on high recycling plasma-wall interaction has exhausted itself at the level of TFTR, JET, JT-60 devices with no realistic path to the burning plasma. Instead, magnetic fusion needs a return to its original idea of insulation of the plasma from the wall, which was the dominant approach in the 1970s and upon implementations has a clear path to the DEMO device with PDT ~= 100 MW and Qelectric > 1 . The SFLiLi systems of this talk is the technology tool for implementation of the guiding idea of magnetic fusion. It utilizes the unique properties of flowing LiLi to pump plasma particles and, thus, insulate plasma from the walls. The necessary flow rate, ~= 1 g3/s, is very small, thus, making the use of lithium practical and consistent with safety requirements. The talk describes how chemical activity of LiLi, which is the major technology challenge of using LiLi in tokamaks, is addressed by SFLiLi systems at the level of already performed (HT-7) experiment, and in ongoing implementations for a prototype of SFLiLi for tokamak divertors and the mid-plane limiter for EAST tokamak (to be tested in the next experimental campaign). This work is supported by US DoE contract No. DE-AC02-09-CH11466.

Burns teaching in UK medical schools: Is it enough?

PubMed

Zinchenko, Ruslan; Perry, Fiona M; Dheansa, Baljit S

2016-02-01

Burns are frequently seen and managed in non-specialist settings. The crowding of the UK medical undergraduate curriculum may have resulted in the reduction of teaching on burns. To determine the burns education experience and the level of competence among UK final year medical students in assessing and acutely managing patients with burns. An online questionnaire was circulated among UK final year medical students. There was a total of 348 respondents. The majority of the respondents (70%) have not received any specific teaching on how to manage patients with burns. Nearly two-thirds of the students (66%) have never seen a patient being managed for burns throughout their training. Over 90% of respondents stated that they would not feel confident in initially managing a burn in the emergency department. The majority of the respondents (57%) have not heard of the criteria for referring a burns patient for further specialist management. There was almost universal agreement about the importance of knowing how to manage a burn initially. There seems to be a lack of consistent undergraduate training in burns management and final year students lack the experience and knowledge to initially manage burns. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Plasma medicine in the Netherlands

NASA Astrophysics Data System (ADS)

Kroesen, Gerrit

2012-10-01

Eindhoven, the Netherlands was one of the locations were Plasma Medicine originated: Eva Stoffels was one of the founders of the field. Since then, the attention for the field steadily increased. Nowadays, strong collaborations exist between the Eindhoven University of Technology (TU/e) and the Red Cross Burn Wound Hospital in Beverwijk, the Amsterdam Medical Center, the Maxima Medical Center in Eindhoven, the Radboud University in Nijmegen, the Free University in Amsterdam, and also companies, both large industries (Philips) and SME's (Vabrema, Lavoisier, Plastech). At TU/e we focus on the plasma itself: developing real time non-invasive diagnostics like TALIF, LIF, IF absorption, Thomson, Rayleigh and Raman scattering, mass spectroscopy, etc, while at the same time developing numerical models on the MD2D platform. For the biology, microbiology and medical aspects we rely on our colleagues who have specialized in those areas. Lesions that are studied are burn wounds, permanent inflammations, diabetic feet, skin infections, and internal diseases like Crohn's disease.

The progress of Chinese burn medicine from the Third Military Medical University-in memory of its pioneer, Professor Li Ao.

PubMed

Li, Haisheng; Zhou, Junyi; Peng, Yizhi; Zhang, Jiaping; Peng, Xi; Luo, Qizhi; Yuan, Zhiqiang; Yan, Hong; Peng, Daizhi; He, Weifeng; Wang, Fengjun; Liang, Guangping; Huang, Yuesheng; Wu, Jun; Luo, Gaoxing

2017-01-01

Professor Li Ao was one of the founders of Chinese burn medicine and one of the most renowned doctors and researchers of burns in China. He established one of the Chinese earliest special departments for burns at Third Military Medical University (TMMU) in 1958. To memorialize Professor Li Ao on his 100th birthday in 2017 and introduce our extensive experience, it is our honor to briefly review the development and achievement of the Chinese burn medicine from TMMU. The epidemiology and outcomes of admitted burn patients since 1958 were reviewed. Furthermore, main achievements of basic and clinical research for the past roughly 60 years were presented. These achievements mainly included the Chinese Rule of Nine, fluid resuscitation protocol, experience in inhalation injury, wound treatment strategies, prevention and treatment of burn infections, nutrition therapy, organ support therapies, and rehabilitation. The progress shaped and enriched modern Chinese burn medicine and promoted the development of world burn medicine.

Duloxetine Plasma Concentrations and Its Effectiveness in the Treatment of Nonorganic Chronic Pain in the Orofacial Region.

PubMed

Kobayashi, Yuka; Nagashima, Wataru; Tokura, Tatsuya; Yoshida, Keizo; Umemura, Eri; Miyauchi, Tomoya; Arao, Munetaka; Ito, Mikiko; Kimura, Hiroyuki; Kurita, Kenichi; Ozaki, Norio

The purpose of this study was to examine the relationship between the pain-relieving effects of duloxetine and its plasma concentrations in patients with burning mouth syndrome and atypical odontalgia characterized by chronic nonorganic pain in the orofacial region. We administered duloxetine to 77 patients diagnosed as having burning mouth syndrome or atypical odontalgia for 12 weeks. The initial dose of duloxetine was established as 20 mg/d and was increased to 40 mg/d after week 2. We evaluated pain using the visual analog scale and depressive symptoms using the Structured Interview Guide for the Hamilton Depression Rating Scale at weeks 0, 2, 4, 6, 8, 10, and 12 and measured plasma concentrations of duloxetine 12 weeks after the start of its administration. Visual analog scale scores were significantly lower 12 weeks after than at the start of the administration of duloxetine (paired t test, t = 6.65, P < 0.0001). We examined the relationship between the rate of decreases in visual analog scale scores and plasma concentrations of duloxetine. There was no significant linear regression or quadratic regression. Duloxetine significantly relieved pain in patients with chronic nonorganic pain in the orofacial region. However, no relationship was observed between its pain-relieving effects and plasma concentrations.

Antithrombin III in animal models of sepsis and organ failure.

PubMed

Dickneite, G

1998-01-01

Antithrombin III (AT III) is the physiological inhibitor of thrombin and other serine proteases of the clotting cascade. In the development of sepsis, septic shock and organ failure, the plasma levels of AT III decrease considerably, suggesting the concept of a substitution therapy with the inhibitor. A decrease of AT III plasma levels might also be associated with other pathological disorders like trauma, burns, pancreatitis or preclampsia. Activation of coagulation and consumption of AT III is the consequence of a generalized inflammation called SIRS (systemic inflammatory response syndrome). The clotting cascade is also frequently activated after organ transplantation, especially if organs are grafted between different species (xenotransplantation). During the past years AT III has been investigated in numerous corresponding disease models in different animal species which will be reviewed here. The bulk of evidence suggests, that AT III substitution reduces morbidity and mortality in the diseased animals. While gaining more experience with AT III, the concept of substitution therapy to maximal baseline plasma levels (100%) appears to become insufficient. Evidence from clinical and preclinical studies now suggests to adjust the AT III plasma levels to about 200%, i.e., doubling the normal value. During the last few years several authors proposed that AT III might not only be an anti-thrombotic agent, but to have in addition an anti-inflammatory effect.

Commissioning and Plans for the NSTX-U Facility

NASA Astrophysics Data System (ADS)

Ono, Masayuki; NSTX-U Team

2016-10-01

The National Spherical Torus Experiment - Upgrade (NSTX-U) has started its first year of plasma operations after the successful completion of the CD-4 milestones. The unique operating regimes of NSTX-U can contribute to several important issues in the physics of burning plasmas to optimize the performance of ITER. The major mission of NSTX-U is also to develop the physics and technology basis for an ST-based Fusion Nuclear Science Facility (FNSF). The new center stack will provide toroidal field of 1 Tesla at a major radius of 0.93 m which should enable a plasma current of up to 2 mega-Amp for 5 sec. A much more tangential 2nd NBI system, with 2-3 times higher current drive efficiency compared to the 1st NBI system, is installed. NSTX-U is designed to attain the 100% non-inductive operation needed for a compact FNSF design. With higher fields and heating powers of 14 MW, the NSTX-U plasma collisionality will be reduced by a factor of 3-6 to help explore the trend in transport towards the low collisionality FNSF regime. If the favorable trends observed on NSTX holds at low collisionality, high fusion neutron fluences could be achievable in very compact ST devices.

Succinylcholine-induced hyperkalemia in the rat following radiation injury to muscle. [60Co

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cairoli, V.J.; Ivankovich, A.D.; Vucicevic, D.

1982-02-01

During anesthetic preparation of a patient who had received routine radiation therapy of sarcoma of the leg, cardiac collapse occurred following succinylcholine (SCh) administration. Experiments were designed to test the hypothesis that radiation injury to muscle might cause increased sensitivity to SCh similar to that reported in patients with muscle trauma, severe burns, and lesions causing muscle denervation. Venous plasma potassium levels and arterial blood gas tensions were measured in rats after they were given SCh (3 mg/kg) at various times following 60Co irradiation of the hind legs. Nonirradiated rats responded to SCh with a slight but statistically significant increasemore » in plasma K+. Rats subjected to high levels of radiation (10,000 to 20,000 R) and given SCh 4 to 7 days later responded in the same way as the control rats. Plasma K+ levels in rats exposed to a fractionated irradiated dosage (25000 R given twice with a 1-week interval) followed by SCh 1 week later were similar to those in the control group, but when SCh was given 2 weeks later (3 weeks after initial irradiation) there was a marked elevation of plasma K+, from 3.6 to 7.7 meq/L, a statistically significant increase.« less

Succinylcholine-induced hyperkalemia in the rat following radiation injury to muscle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cairoli, V.J.; Ivankovich, A.D.; Vucicevic, D.

1982-02-01

During anesthetic preparation of a patient who had received routine radiation therapy for sarcoma of the leg, cardiac collapse occurred following succinylcholine (SCh) administration. Experiments were designed to test the hypothesis that radiation injury to muscle might cause increased sensitivity to SCh similar to that reported in patients with muscle trauma, severe burns, and lesions causing muscle denervation. Venous plasma potassium levels and arterial blood gas tensions were measured in rats after they were given SCh (3 mg/kg) at various times following /sup 60/Co irradiation of the hind legs. Nonirradiated rats responded to SCh with a slight but statistically significantmore » increase in plasma K+. Rats subjected to high levels of radiation (10,000 to 20,000 R) and given SCh 4 to 7 days later responded in the same way as the control rats. Plasma K+ levels in rats exposed to a fractionated irradiated dosage (2500 R given twice with a 1-week interval) followed by SCh 1 week later were similar to those in the control group, but when SCh was given 2 weeks later (3 weeks after initial irradiation) there was a marked elevation of plasma K+, from 3.6 to 7.7 meq/L, a statistically significant increase.« less

Conductor analysis of the ITER FEAT poloidal field coils during a plasma scenario

NASA Astrophysics Data System (ADS)

Nicollet, S.; Hertout, P.; Duchateau, J. L.; Bleyer, A.; Bessette, D.

2002-05-01

In the framework of the ITER (International Thermonuclear Experimental Reactor) FEAT (Fusion Energy Advanced Tokamak) project, a fully superconducting PF (Poloidal Field) system has been designed in detail. The Central Solenoid and the 6 equilibrium coils constituting the PF system provide the magnetic fields which develop, shape and control the 15 MA plasma during the 1800 s of a typical plasma scenario. The 6 PF coils will be wound two-in-hand from a 45 kA niobium-titanium CICC (Cable-In-Conduit-Conductor). These coils will experience severe heat loads specially during the 400 s of the plasma burn: nuclear heating due to the 400 MW of fusion power, thermal radiation and AC losses (30 to 300 kJ). The AC losses along the PF coil pancakes are deduced from accurate magnetic field computations performed with a 3D magnetostatic code, TRAPS. The nuclear heating and the thermal radiation are assumed to be uniform over a given face of the PF coils. These heat loads are used as input to perform the thermal and hydraulic analysis with a finite element code, GANDALF. The temperature increases (0.1 to 0.4 K) are computed, the margins and performances of the conductor are evaluated.

Pre-hospital burn mission as a unique experience: a qualitative study.

PubMed

Froutan, Razieh; Khankeh, Hamid Reza; Fallahi, Masoud; Ahmadi, Fazlollah; Norouzi, Kian

2014-12-01

A thorough understanding of experiences related to pre-hospital emergency care of burns is a prerequisite of skill promotion for medical personnel. The aim of the present study was to evaluate the experiences of pre-hospital emergency personnel during burn accidents. The present qualitative study was performed using a content analysis method. In total, 18 Iranian emergency care personnel participated in the study. A purposeful sampling method was applied until reaching data saturation. Data were collected using semi-structured interviews and field observations. Afterwards, the gathered data were analyzed through face content analysis. By analyzing 498 primary codes, four main categories; the nature of burn care, tension at the accident scene, gradual job 'burnout', and insufficient information, were extracted from the experiences of pre-hospital emergency personnel during burn care. These categories each included several sub-categories, which were classified according to their significant characteristics. This study showed that different factors affect the quality of pre-hospital clinical services for burns. Authorities and health system administrators should consider the physical and psychological health of their staff, and assign policies to improve the quality of pre-hospital medical care. According to the present results, it is recommended that the process of pre-hospital emergency care for burns be investigated further. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Fluid-Plasma-Combustion Coupling Effects on the Ignition of a Fuel Jet

NASA Astrophysics Data System (ADS)

Massa, Luca; Freund, Jonathan

2016-11-01

We analyze the effect of plasma-combustion coupling on the ignition and flame supported by a DBD interacting with a jet of H2 in a air cross-flow. We propose that plasma-combustion coupling is due to the strong temperature-dependence of specific collisional energy loss as predicted by the Boltzmann equation, and that e- transport can be modeled by assuming a form for the E-field pulse in microstreamers. We introduce a two-way coupling based on the Boltzmann equation and the charged species conservation. The addition of this mechanism to a hydrogen combustion scheme leads to an improvement of the ignition prediction and of the understanding of the effect of the plasma on the flow. The key points of the analysis are 1) explanation of the mechanism for the two-stage ignition and quenching observed experimentally, 2) explanation of the existence of a power threshold above which the plasma is beneficial to the ignition probability, 3) understanding of the increase in power absorbed by the plasma in burning conditions and the reduction in power absorbed with an increase in the cross velocity, 4) explanation of the non-symmetric emissions and the increase in luminescence at the rotovibrational H2O band. The model is validated in part against air-H2 flow experiments. This material is based in part upon work supported by the Department of Energy, National Nuclear Security Administration, under Award Number DE-NA0002374.

Modeling crop residue burning experiments to evaluate smoke emissions and plume transport

Treesearch

Luxi Zhou; Kirk R. Baker; Sergey L. Napelenok; George Pouliot; Robert Elleman; Susan M. O' Neill; Shawn P. Urbanski; David C. Wong

2018-01-01

Crop residue burning is a common land management practice that results in emissions of a variety of pollutants with negative health impacts. Modeling systems are used to estimate air quality impacts of crop residue burning to support retrospective regulatory assessments and also for forecasting purposes. Ground and airborne measurements from a recent field experiment...

Fusion plasma theory project summaries

NASA Astrophysics Data System (ADS)

1993-10-01

This Project Summary book is a published compilation consisting of short descriptions of each project supported by the Fusion Plasma Theory and Computing Group of the Advanced Physics and Technology Division of the Department of Energy, Office of Fusion Energy. The summaries contained in this volume were written by the individual contractors with minimal editing by the Office of Fusion Energy. Previous summaries were published in February of 1982 and December of 1987. The Plasma Theory program is responsible for the development of concepts and models that describe and predict the behavior of a magnetically confined plasma. Emphasis is given to the modelling and understanding of the processes controlling transport of energy and particles in a toroidal plasma and supporting the design of the International Thermonuclear Experimental Reactor (ITER). A tokamak transport initiative was begun in 1989 to improve understanding of how energy and particles are lost from the plasma by mechanisms that transport them across field lines. The Plasma Theory program has actively participated in this initiative. Recently, increased attention has been given to issues of importance to the proposed Tokamak Physics Experiment (TPX). Particular attention has been paid to containment and thermalization of fast alpha particles produced in a burning fusion plasma as well as control of sawteeth, current drive, impurity control, and design of improved auxiliary heating. In addition, general models of plasma behavior are developed from physics features common to different confinement geometries. This work uses both analytical and numerical techniques. The Fusion Theory program supports research projects at U.S. government laboratories, universities and industrial contractors. Its support of theoretical work at universities contributes to the office of Fusion Energy mission of training scientific manpower for the U.S. Fusion Energy Program.

Progress toward commissioning and plasma operation in NSTX-U

NASA Astrophysics Data System (ADS)

Ono, M.; Chrzanowski, J.; Dudek, L.; Gerhardt, S.; Heitzenroeder, P.; Kaita, R.; Menard, J. E.; Perry, E.; Stevenson, T.; Strykowsky, R.; Titus, P.; von Halle, A.; Williams, M.; Atnafu, N. D.; Blanchard, W.; Cropper, M.; Diallo, A.; Gates, D. A.; Ellis, R.; Erickson, K.; Hosea, J.; Hatcher, R.; Jurczynski, S. Z.; Kaye, S.; Labik, G.; Lawson, J.; LeBlanc, B.; Maingi, R.; Neumeyer, C.; Raman, R.; Raftopoulos, S.; Ramakrishnan, R.; Roquemore, A. L.; Sabbagh, S. A.; Sichta, P.; Schneider, H.; Smith, M.; Stratton, B.; Soukhanovskii, V.; Taylor, G.; Tresemer, K.; Zolfaghari, A.; The NSTX-U Team

2015-07-01

The National Spherical Torus Experiment-Upgrade (NSTX-U) is the most powerful spherical torus facility at PPPL, Princeton USA. The major mission of NSTX-U is to develop the physics basis for an ST-based Fusion Nuclear Science Facility (FNSF). The ST-based FNSF has the promise of achieving the high neutron fluence needed for reactor component testing with relatively modest tritium consumption. At the same time, the unique operating regimes of NSTX-U can contribute to several important issues in the physics of burning plasmas to optimize the performance of ITER. NSTX-U further aims to determine the attractiveness of the compact ST for addressing key research needs on the path toward a fusion demonstration power plant (DEMO). The upgrade will nearly double the toroidal magnetic field BT to 1 T at a major radius of R0 = 0.93 m, plasma current Ip to 2 MA and neutral beam injection (NBI) heating power to 14 MW. The anticipated plasma performance enhancement is a quadrupling of the plasma stored energy and near doubling of the plasma confinement time, which would result in a 5-10 fold increase in the fusion performance parameter nτ T. A much more tangential 2nd NBI system, with 2-3 times higher current drive efficiency compared to the 1st NBI system, is installed to attain the 100% non-inductive operation needed for a compact FNSF design. With higher fields and heating powers, the NSTX-U plasma collisionality will be reduced by a factor of 3-6 to help explore the favourable trend in transport towards the low collisionality FNSF regime. The NSTX-U first plasma is planned for the Summer of 2015, at which time the transition to plasma operations will occur.

An Overview of Regional Experiments on Biomass Burning Aerosols and Related Pollutants in Southeast Asia: From BASE-ASIA and the Dongsha Experiment to 7-SEAS

NASA Technical Reports Server (NTRS)

Lin, Neng-Huei; Tsay, Si-Chee; Maring, Hal B.; Yen, Ming-Cheng; Sheu, Guey-Rong; Wang, Sheng-Hsiang; Chi, Kai Hsien; Chuang, Ming-Tung; Ou-Yang, Chang-Feng; Fu, Joshua S.;

Influence of fast alpha diffusion and thermal alpha buildup on tokamak reactor performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uckan, N.A.; Tolliver, J.S.; Houlberg, W.A.

1987-11-01

The effect of fast alpha diffusion and thermal alpha accumulation on the confinement capability of a candidate Engineering Test Reactor (ETR) plasma (Tokamak Ignition/Burn Experimental Reactor (TIBER-II)) in achieving ignition and steady-state driven operation has been assessed using both global and 1-1/2-D transport models. Estimates are made of the threshold for radial diffusion of fast alphas and thermal alpha buildup. It is shown that a relatively low level of radial transport, when combined with large gradients in the fast alpha density, leads to a significant radial flow with a deleterious effect on plasma performance. Similarly, modest levels of thermal alphamore » concentration significantly influence the ignition and steady-state burn capability. 23 refs., 9 figs., 4 tabs.« less

Tridimensional Thermonuclear Instability in Subignited Plasmas and on the Surface of the Pulsars

NASA Astrophysics Data System (ADS)

Cardinali, A.; Coppi, B.

2016-10-01

Tridimensional modes involving an increase of the electron temperature can be excited as a result of α-particle heating in subignited D-T fusion burning plasmas when a nearly time- independent external source of heating is applied. The analyzed modes are shown to emerge from an axisymmetric toroidal configurations and are radially localized around rational magnetic surfaces corresponding to q(r =r0) =m0 /n0 where m0 and n0 are the relevant poloidal and toroidal mode numbers. The radial width of the mode is of the order of the thermal scale distances δT =D⊥e th /D∥e th 1/4 (R0 /n0) 1/2(dlnq/dr)0-1/2. The mode has a rather severe damping rate, that has to be overcome by the relevant heating rate. Thus the temperature range to be considered is that where the D-T plasma reactivity undergoes a relatively large increase as a function of temperature. This kind of theory has been applied to the plasmas that are envisioned to be associated with surface of pulsar and be subjects to (spatially) inhomogenous thermonuclear burning. Sponsored in part by the US DOE.

Contributions of Severe Burn and Disuse to Bone Structure and Strength in Rats

PubMed Central

Baer, L.A.; Wu, X.; Tou, J. C.; Johnson, E.; Wolf, S.E.; Wade, C.E.

2012-01-01

Burn and disuse results in metabolic and bone changes associated with substantial and sustained bone loss. Such loss can lead to an increased fracture incidence and osteopenia. We studied the independent effects of burn and disuse on bone morphology, composition and strength, and microstructure of the bone alterations 14 days after injury. Sprague-Dawley rats were randomized into four groups: Sham/Ambulatory (SA), Burn/Ambulatory (BA), Sham/Hindlimb Unloaded (SH) and Burn/Hindlimb Unloaded (BH). Burn groups received a 40% total body surface area full-thickness scald burn. Disuse by hindlimb unloading was initiated immediately following injury. Bone turnover was determined in plasma and urine. Femur biomechanical parameters were measured by three-point bending tests and bone microarchitecture was determined by microcomputed tomography (uCT). On day 14, a significant reduction in body mass was observed as a result of burn, disuse and a combination of both. In terms of bone health, disuse alone and in combination affected femur weight, length and bone mineral content. Bending failure energy, an index of femur strength, was significantly reduced in all groups and maximum bending stress was lower when burn and disuse were combined. Osteocalcin was reduced in BA compared to the other groups, indicating influence of burn. The reductions observed in femur weight, BMC, biomechanical parameters and indices of bone formation are primarily responses to the combination of burn and disuse. These results offer insight into bone degradation following severe injury and disuse. PMID:23142361

Development of a He- and He0 beam source for alpha particle measurement in a burning plasma.

PubMed

Tanaka, N; Sasao, M; Terai, K; Okamoto, A; Kitajima, S; Yamaoka, H; Wada, M

2012-02-01

Proof of principle experiments of neutral helium beam production for alpha particle diagnostics was carried out on a test stand. Negative helium ions were produced in the Li charge exchange cell, in which stable and long time operation was possible. He(-) beam was accelerated to 157 keV. Finally, He(0) beam was successfully produced after the flight in the drift-tube through the auto-electron-detachment process from He(-) to He(0). A neutral beam detector using a pyroelectric device was also developed to measure He(0) beam intensity. The metastable component in the neutral helium beam was found to be less than 2%.

The effect of supplemental enteral glutamine on plasma levels, gut function, and outcome in severe burns: a randomized, double-blind, controlled clinical trial.

PubMed

Zhou, Ye-Ping; Jiang, Zhu-Ming; Sun, Yong-Hua; Wang, Xiu-Rong; Ma, En-Ling; Wilmore, Douglas

2003-01-01

This research was conducted to evaluate the effect of enterally administered glutamine (gln) dipeptide on metabolic, gastrointestinal, and outcome parameters after severe burn injury. Forty thermally injured patients with total body surface burns ranging between 50% and 80%, and third-degree burns ranging between 20% and 40% and without respiratory injuries, were randomized into a prospective, double-blind, controlled clinical trial. One group received gln-enriched enteral nutrition and the other group received the standard enteral formulation. Tube feedings were initiated on postburn day 1 (PBD +1), and isocaloric and isonitrogenous feedings were administered to both groups until PBD +12. The gln was given as the dipeptide of alanyl-gln (Ajinomoto, Tokyo, Japan), which provided 0.35 g gln/kg body weight/d. Plasma amino acid profiles, serum endotoxin concentrations, and the lactulose/mannitol absorption ratio (which reflects gut permeability) were measured at specific times throughout the clinical course. Wound healing at day 30 was assessed, and length of hospital stay and total costs were determined at discharge. The 2 groups were similar in terms of age and extent of injury. Plasma gln concentrations were approximately 300 umol/L in both groups on PBD +1 and remained low in the control group (399 +/- 40 umol/L, mean +/- SD) but increased toward normal in the supplemented group to 591 +/- 74 (p = .048). Lactulose/mannitol ratios were increased above normal on POD +1 (control, 0.221 +/- 0.169; gln, 0.268 +/- 0.202; not significant), reflecting increased intestinal permeability after burn injury. On POD +3, the ratio in the gln group was lower than control (0.025 +/- 0.008 versus 0.049 +/- 0.016; p = .0001), and both groups returned toward normal ratios with time. Endotoxin levels on PBD +1 were elevated in both groups (control, 0.089 +/- 0.023 EU/mL; gln, 0.103 +/- 0.037 EU/mL; NS) but decreased significantly on PBD +3 in the patients receiving gln. Hospital stay was significantly shorter in the gln group than controls (67 +/- 4 days versus 73 +/- 6; p = .026). On day 30, wound healing was 86% +/- 2% complete in the gln group compared with 72% +/- 3% in controls (p = .041). Total cost of hospitalization was 62794 +/- 6178 RMB (dollar 7593 +/- 747 US dollars) in the gln group and 68996 +/- 8620RMB (dollar 8343 +/- 1042, p = .031) in controls, although the cost of the enteral nutrition was higher in the gln-supplemented patients. Enteral gln supplementation using a commercially available dipeptide supported plasma gln levels, improved gut permeability, and initially decreased plasma endotoxin levels in severely thermally injured patients. These alterations were associated with a reduction in the length of hospitalization and lower costs.

Results from MARBLE DT Experiments on the National Ignition Facility: Implosion of Foam-Filled Capsules for Studying Thermonuclear Burn in the Presence of Heterogeneous Mix

NASA Astrophysics Data System (ADS)

Murphy, T. J.; Douglas, M. R.; Cardenas, T.; Cooley, J. H.; Gunderson, M. A.; Haines, B. M.; Hamilton, C. E.; Kim, Y.; Lee, M. N.; Oertel, J. A.; Olson, R. E.; Randolph, R. B.; Shah, R. C.; Smidt, J. M.

2017-10-01

The MARBLE campaign on NIF investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. MARBLE utilizes plastic capsules filled with deuterated plastic foam and tritium gas. The ratio of DT to DD neutron yield is indicative of the degree to which the foam and the gas atomically mix. Platform development experiments have been performed to understand the behavior of the foam and of the gas separately using two types of capsule. The first experiments using deuterated foam and tritium gas have been performed. Results of these experiments, and the implications for our understanding of thermonuclear burn in heterogeneously mixed separated reactant experiments will be discussed. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Adult survivors' lived experience of burns and post-burn health: A qualitative analysis.

PubMed

Abrams, Thereasa E; Ogletree, Roberta J; Ratnapradipa, Dhitinut; Neumeister, Michael W

2016-02-01

The individual implications of major burns are likely to affect the full spectrum of patients' physical, emotional, psychological, social, environmental, spiritual and vocational health. Yet, not all of the post-burn health implications are inevitably negative. Utilizing a qualitative approach, this heuristic phenomenological study explores the experiences and perceptions early (ages 18-35) and midlife (ages 36-64) adults providing insight for how participants perceived their burns in relationship to their post-burn health. Participants were interviewed using semi-structured interview questions framed around seven domains of health. Interview recordings were transcribed verbatim then coded line by line, identifying dominant categories related to health. Categories were analyzed identifying shared themes among the study sample. Participants were Caucasian, seven males and one female. Mean age at time of interviews was 54.38 and 42.38 at time of burns. Mean time since burns occurred was 9.38 years with a minimum of (20%) total body surface area (TBSA) burns. Qualitative content analysis rendered three emergent health-related categories and associated themes that represented shared meanings within the participant sample. The category of "Physical Health" reflected the theme physical limitations, pain and sensitivity to temperature. Within the category of "Intellectual Health" were themes of insight, goal setting and self-efficacy, optimism and humor and within "Emotional Health" were the themes empathy and gratitude. By exploring subjective experiences and perceptions of health shared through dialog with experienced burned persons, there are opportunities to develop a more complete picture of how holistic health may be affected by major burns that in turn could support future long-term rehabilitative trajectories of early and midlife adult burn patients. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

A modified surgical technique in the management of eyelid burns: a case series

PubMed Central

2011-01-01

Introduction Contractures, ectropion and scarring, the most common sequelae of skin grafts after eyelid burn injuries, can result in corneal exposure, corneal ulceration and even blindness. Split-thickness or full-thickness skin grafts are commonly used for the treatment of acute eyelid burns. Plasma exudation and infection are common early complications of eyelid burns, which decrease the success rate of grafts. Case presentation We present the cases of eight patients, two Chinese women and six Chinese men. The first Chinese woman was 36 years old, with 70% body surface area second or third degree flame burn injuries involving her eyelids on both sides. The other Chinese woman was 28 years old, with sulfuric acid burns on her face and third degree burn on her eyelids. The six Chinese men were aged 21, 31, 38, 42, 44, and 55 years, respectively. The 38-year-old patient was transferred from the ER with 80% body surface area second or third degree flame burn injuries and third degree burn injuries to his eyelids. The other five men were all patients with flame burn injuries, with 7% to 10% body surface area third degree burns and eyelids involved. All patients were treated with a modified surgical procedure consisting of separation and loosening of the musculus orbicularis oculi between tarsal plate and septum orbital, followed by grafting a large full-thickness skin graft in three days after burn injury. The use of our modified surgical procedure resulted in 100% successful eyelid grafting on first attempt, and all our patients were in good condition at six-month follow-up. Conclusions This new surgical technique is highly successful in treating eyelid burn injuries, especially flame burn injuries of the eyelid. PMID:21843322

Improving the accuracy of burn-surface estimation.

PubMed

Nichter, L S; Williams, J; Bryant, C A; Edlich, R F

1985-09-01

A user-friendly computer-assisted method of calculating total body surface area burned (TBSAB) has been developed. This method is more accurate, faster, and subject to less error than conventional methods. For comparison, the ability of 30 physicians to estimate TBSAB was tested. Parameters studied included the effect of prior burn care experience, the influence of burn size, the ability to accurately sketch the size of burns on standard burn charts, and the ability to estimate percent TBSAB from the sketches. Despite the ability for physicians of all levels of training to accurately sketch TBSAB, significant burn size over-estimation (p less than 0.01) and large interrater variability of potential consequence was noted. Direct benefits of a computerized system are many. These include the need for minimal user experience and the ability for wound-trend analysis, permanent record storage, calculation of fluid and caloric requirements, hemodynamic parameters, and the ability to compare meaningfully the different treatment protocols.

Active spectroscopic measurements using the ITER diagnostic system.

PubMed

Thomas, D M; Counsell, G; Johnson, D; Vasu, P; Zvonkov, A

2010-10-01

Active (beam-based) spectroscopic measurements are intended to provide a number of crucial parameters for the ITER device being built in Cadarache, France. These measurements include the determination of impurity ion temperatures, absolute densities, and velocity profiles, as well as the determination of the plasma current density profile. Because ITER will be the first experiment to study long timescale (∼1 h) fusion burn plasmas, of particular interest is the ability to study the profile of the thermalized helium ash resulting from the slowing down and confinement of the fusion alphas. These measurements will utilize both the 1 MeV heating neutral beams and a dedicated 100 keV hydrogen diagnostic neutral beam. A number of separate instruments are being designed and built by several of the ITER partners to meet the different spectroscopic measurement needs and to provide the maximum physics information. In this paper, we describe the planned measurements, the intended diagnostic ensemble, and we will discuss specific physics and engineering challenges for these measurements in ITER.

High frequency fishbone driven by passing energetic ions in tokamak plasmas

NASA Astrophysics Data System (ADS)

Wang, Feng; Yu, L. M.; Fu, G. Y.; Shen, Wei

2017-05-01

High frequency fishbone instability driven by passing energetic ions was first reported in the Princeton beta experiment with tangential neutral-beam-injection (Heidbrink et al 1986 Phys. Rev. Lett. 57 835-8). It could play an important role for ITER-like burning plasmas, where α particles are mostly passing particles. In this work, a generalized energetic ion distribution function and finite drift orbit width effect are considered to improve the theoretical model for passing particle driving fishbone instability. For purely passing energetic ions with zero drift orbit width, the kinetic energy δ {{W}k} is derived analytically. The derived analytic expression is more accurate as compared to the result of previous work (Wang 2001 Phys. Rev. Lett. 86 5286-8). For a generalized energetic ion distribution function, the fishbone dispersion relation is derived and is solved numerically. Numerical results show that broad and off-axis beam density profiles can significantly increase the beam ion beta threshold {βc} for instability and decrease mode frequency.

High frequency fishbone driven by passing energetic ions in tokamak plasmas

DOE PAGES

Wang, Feng; Yu, L. M.; Fu, G. Y.; ...

2017-03-22

High frequency fishbone instability driven by passing energetic ions was first reported in the Princeton beta experiment with tangential neutral-beam-injection (Heidbrink et al 1986 Phys. Rev. Lett. 57 835–8). It could play an important role for ITER-like burning plasmas, where α particles are mostly passing particles. In this work, a generalized energetic ion distribution function and finite drift orbit width effect are considered to improve the theoretical model for passing particle driving fishbone instability. For purely passing energetic ions with zero drift orbit width, the kinetic energymore » $$\\delta {{W}_{k}}$$ is derived analytically. The derived analytic expression is more accurate as compared to the result of previous work. For a generalized energetic ion distribution function, the fishbone dispersion relation is derived and is solved numerically. As a result, numerical results show that broad and off-axis beam density profiles can significantly increase the beam ion beta threshold $${{\\beta}_{c}}$$ for instability and decrease mode frequency.« less

Observation of Compressible Plasma Mix in Cylindrically Convergent Implosions

NASA Astrophysics Data System (ADS)

Barnes, Cris W.; Batha, Steven H.; Lanier, Nicholas E.; Magelssen, Glenn R.; Tubbs, David L.; Dunne, A. M.; Rothman, Steven R.; Youngs, David L.

2000-10-01

An understanding of hydrodynamic mix in convergent geometry will be of key importance in the development of a robust ignition/burn capability on NIF, LMJ and future pulsed power machines. We have made use of the OMEGA laser facility at the University of Rochester to investigate directly the mix evolution in a convergent geometry, compressible plasma regime. The experiments comprise a plastic cylindrical shell imploded by direct laser irradiation. The cylindrical shell surrounds a lower density plastic foam which provides sufficient back pressure to allow the implosion to stagnate at a sufficiently high radius to permit quantitative radiographic diagnosis of the interface evolution near turnaround. The susceptibility to mix of the shell-foam interface is varied by choosing different density material for the inner shell surface (thus varying the Atwood number). This allows the study of shock-induced Richtmyer-Meshkov growth during the coasting phase, and Rayleigh-Taylor growth during the stagnation phase. The experimental results will be described along with calculational predictions using various radiation hydrodynamics codes and turbulent mix models.

Alternative complement pathway activation increases mortality in a model of burn injury in mice.

PubMed Central

Gelfand, J A; Donelan, M; Hawiger, A; Burke, J F

1982-01-01

We have studied the role of the complement system in burn injury in an experimental model in mice. A 25% body surface area, full-thickness scald wound was produced in anesthetized animals. Massive activation of the alternative complement pathway, but not the classical pathway, was seen. This activation was associated with the generation of neutrophil aggregating activity in the plasma, neutrophil aggregates in the lungs, increased pulmonary vascular permeability, and increased lung edema formation. Decomplementation with cobra venom factor (CVF) or genetic C5 deficiency diminished these pathologic changes, and CVF pretreatment substantially reduced burn mortality in the first 24 h. Preliminary data show that human burn patients have a similar pattern of complement activation involving predominantly the alternative pathway, indicating the possible relevance of the murine model to human disease. Images PMID:7174787

Effect of the self-pumped limiter concept on the tritium fuel cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finn, P.A.; Sze, D.K.; Hassanein, A.

1988-01-01

The self-pumped limiter concept for impurity control of the plasma of a fusion reactor has a major impact on the design of the tritium systems. To achieve a sustained burn, conventional limiters and divertors remove large quantities of unburnt tritium and deuterium from the plasma which must be then recycled using a plasma processing system. The self-pumped limiter which does not remove the hydrogen species, does not require any plasma processing equipment. The blanket system and the coolant processing systems acquire greater importance with the use of this unconventional impurity control system. 3 refs., 2 figs.

The inter-rater reliability of estimating the size of burns from various burn area chart drawings.

PubMed

Wachtel, T L; Berry, C C; Wachtel, E E; Frank, H A

2000-03-01

The accuracy and variability of burn size calculations using four Lund and Browder charts currently in clinical use and two Rule of Nine's diagrams were evaluated. The study showed that variability in estimation increased with burn size initially, plateaued in large burns and then decreased slightly in extensive burns. The Rule of Nine's technique often overestimates the burn size and is more variable, but can be performed somewhat faster than the Lund and Browder method. More burn experience leads to less variability in burn area chart drawing estimates. Irregularly shaped burns and burns on the trunk and thighs had greater variability than less irregularly shaped burns or burns on more defined anatomical parts of the body.

Close-out report with links to abstracts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marmar, Earl S.

This grant provided A/V support for two technical meetings of the Edge Coordinating Committee: (1) Nov 13, 2013 (co-located with the APS-DPP meeting in Denver, CO) https://ecc.mit.edu/fall-2013-technical-meeting#overlay-context=ecc-meetings; (2) April 28-May 1, 2015 (embedded sessions in the Transport Task Force Meeting, Salem, MA) http://www-internal.psfc.mit.edu/TTF2015/index.html. The ultimate goal of the U.S. Transport Task Force is to develop a physics-based understanding of particle, momentum and heat transport in magnetic fusion devices. This understanding should be of sufficient depth that it allows the development of predictive models of plasma transport that can be validated against experiment, and then used to anticipate the future performancemore » of burning plasmas in ITER, as well as to provide guidance for the design of next-step fusion nuclear science facilities. To achieve success in transport science, it is essential to characterize local fluctuations and transport in toroidal plasmas, to understand the basic mechanisms responsible for transport, and ultimately to control these transport processes. These goals must be pursued in multiple areas, and these topics evolve in order to reflect current interests.« less

Antimatter Driven P-B11 Fusion Propulsion System

NASA Technical Reports Server (NTRS)

Kammash, Terry; Martin, James; Godfroy, Thomas

2002-01-01

One of the major advantages of using P-B11 fusion fuel is that the reaction produces only charged particles in the form of three alpha particles and no neutrons. A fusion concept that lends itself to this fuel cycle is the Magnetically Insulated Inertial Confinement Fusion (MICF) reactor whose distinct advantage lies in the very strong magnetic field that is created when an incident particle (or laser) beam strikes the inner wall of the target pellet. This field serves to thermally insulate the hot plasma from the metal wall thereby allowing thc plasma to burn for a long time and produce a large energy magnification. If used as a propulsion device, we propose using antiprotons to drive the system which we show to be capable of producing very large specific impulse and thrust. By way of validating the confinement propenies of MICF we will address a proposed experiment in which pellets coated with P-B11 fuel at the appropriate ratio will be zapped by a beam of antiprotons that enter the target through a hole. Calculations showing the density and temperature of the generated plasma along with the strength of the magnetic field and other properties of the system will be presented and discussed.

Elimination of dimethyl methylphosphonate by plasma flame made of microwave plasma and burning hydrocarbon fuel

NASA Astrophysics Data System (ADS)

Cho, S. C.; Uhm, H. S.; Hong, Y. C.; Park, Y. G.; Park, J. S.

2008-06-01

Elimination of dimethyl methylphosphonate (DMMP) in liquid phase was studied by making use of a microwave plasma burner, exhibiting a safe removal capability of stockpiled chemical weapons. The microwave plasma burner consisted of a fuel injector and a plasma flame exit connected in series to a microwave plasma torch. The burner flames were sustained by injecting hydrocarbon fuels into the microwave plasma torch in air discharge. The Fourier transform infrared spectra indicated near perfect elimination of DMMP in the microwave plasma burner. This was confirmed by gas chromatography spectra as supporting data, revealing the disappearance of even intermediary compounds in the process of DMMP destruction. The experimental results and the physical configuration of the microwave plasma burner may provide an effective means of on-site removal of chemical warfare agents found on a battlefield.

Shall We Continue to Teach the Candle Burning Experiment at Lower Secondary Level?

ERIC Educational Resources Information Center

Dhindsa, Harkirat S.

2005-01-01

The candle burning experiment is usually conducted in lower secondary classes to prove the (about) 20% oxygen in air. The aim of this paper is to show that teachers misinterpret the results of the experiment to satisfy the objectives of teaching this experiment. However, when the results of this experiment are interpreted correctly, the objectives…

Crucial issues of multi-beam feed-back control with ECH/ECCD in fusion plasmas

NASA Astrophysics Data System (ADS)

Cirant, S.; Berrino, J.; Gandini, F.; Granucci, G.; Iannone, F.; Lazzaro, E.; D'Antona, G.; Farina, D.; Koppenburg, K.; Nowak, S.; Ramponi, G.

2005-01-01

Proof of principle of feed-back controlled Electron Cyclotron Heating and Current Drive (ECH/ECCD), aiming at automatic limitation (or suppression) of Neoclassical Tearing Modes amplitude, has been achieved in a number of present machines. In addition to Neoclassical Tearing Mode stabilization, more applications of well-localized ECH/ECCD can be envisaged (saw-tooth crash control, current profile control, thermal barrier control, disruption mitigation). However, in order to be able to take a step forward towards the application of these techniques to burning plasmas, some crucial issues should be more deeply analyzed: multi-beam simultaneous action, control of deposition radii rdep, diagnostic of plasma reaction. So far the Electron Cyclotron Emission has been the most important tool to get localized information on plasma response, essential for both rdep and risland recognition, but its use in very hot burning plasmas within automatic control loops should be carefully verified. Assuming that plasma response is appropriately diagnosed, the next matter to be discussed concerns how to control rdep, since all techniques so far used, or proposed (plasma position, toroidal field, mechanical beam steering, gyrotron frequency tuning) have limitations or drawbacks. Finally, simultaneous multiple actions on many actuators (EC beams), concurring to automatic control of one single parameter (e.g. NTM amplitude) might be a challenging task for the controller, particularly in view of the fact that any effect of each beam becomes visible only when it is positioned very close to the right radius. All these interlinked aspects are discussed in the paper.

Inappropriate Vasopressin Secretion (SIADH) in Burned Patients

DTIC Science & Technology

1983-03-01

cular route, can promote the secretion of AVP in animals effective arterial volume relative to increased metabolic (24, 28, 29). Plasma renin activity...caloric intake (estimated resting metabolic (ileus or obtundation) were considered separately (Figs. rate, +25%) was begun in the first week. Morphine...further suggest adequate effective volume. for AVP secretion is set at a lower than normal plasma Whether the hypermetabolic state and increased O de

Outcomes After Cardiac Arrest in an Adult Burn Center

DTIC Science & Technology

2013-12-07

defibrillation at our institution, either in the burn operating room (BOR) or burn intensive care unit (BICU). We included patients who experi- enced CA in...of this study design. In other studies, the time between CA and defibrillation and, in children, the time between burn and fluid resuscitation have

Droplet burning at zero G

NASA Technical Reports Server (NTRS)

Williams, F. A.

1978-01-01

Questions of the importance and feasibility of performing experiments on droplet burning at zero gravity in Spacelab were studied. Information on the physics and chemistry of droplet combustion, with attention directed specifically to the chemical kinetics, heat and mass transfer, and fluid mechanics of the phenomena involved, are presented. The work was divided into three phases, the justification, the feasibility, and the conceptual development of a preliminary design. Results from the experiments performed revealed a few new facts concerning droplet burning, notably burning rates in excess of theoretical prediction and a phenomenon of flash extinction, both likely traceable to accumulation of carbon produced by gas-phase pyrolysis in the fuel-rich zone enclosed by the reaction surface. These experiments also showed that they were primarily due to timing difficulties.

Magnetic geometry and physics of advanced divertors: The X-divertor and the snowflake

NASA Astrophysics Data System (ADS)

Kotschenreuther, Mike; Valanju, Prashant; Covele, Brent; Mahajan, Swadesh

2013-10-01

Advanced divertors are magnetic geometries where a second X-point is added in the divertor region to address the serious challenges of burning plasma power exhaust. Invoking physical arguments, numerical work, and detailed model magnetic field analysis, we investigate the magnetic field structure of advanced divertors in the physically relevant region for power exhaust—the scrape-off layer. A primary result of our analysis is the emergence of a physical "metric," the Divertor Index DI, which quantifies the flux expansion increase as one goes from the main X-point to the strike point. It clearly separates three geometries with distinct consequences for divertor physics—the Standard Divertor (DI = 1), and two advanced geometries—the X-Divertor (XD, DI > 1) and the Snowflake (DI < 1). The XD, therefore, cannot be classified as one variant of the Snowflake. By this measure, recent National Spherical Torus Experiment and DIIID experiments are X-Divertors, not Snowflakes.

Individual Sawtooth Pacing by Synchronized ECCD in TCV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goodman, T. P.; Felici, F.; Canal, G.

2011-12-23

Previous real-time sawtooth control scenarios using EC actuators have attempted to shorten or lengthen the sawtooth period by optimally positioning the EC absorption near the q = 1 surface. In new experiments we demonstrate for the first time that individual sawtooth crashes can be repetitively induced at predictable times by reducing the stabilizing ECCD power after a predetermined time from the preceding crash. Other stabilizing actuators (e.g. ICRF, NBI) are expected to produce similar effects. Armed with these results, we present a new sawtooth / NTM control paradigm for improved performance in burning plasmas. The potential appearance of neo-classical tearingmore » modes, triggered by long period sawtooth crashes even at low beta, becomes predictable and therefore amenable to preemptive ECCD. The ITER Electron Cyclotron Upper Launcher (EC-UL) design incorporates the needed functionalities for this method to be applied. The methodology and associated TCV experiments will be presented.« less

Exploring the dynamics of kinetic/multi-ion effects and ion-electron equilibration rates in ICF plasmas at OMEGA

NASA Astrophysics Data System (ADS)

Sio, H.

2017-10-01

During the last few years, an increasing number of experiments have shown that kinetic and multi-ion-fluid effects do impact the performance of an ICF implosion. Observations include: increasing yield degradation as the implosion becomes more kinetic; thermal decoupling between ion species; anomalous yield scaling for different fuel mixtures; ion diffusion; and fuel stratification. The common theme in these experiments is that the results are based on time-integrated nuclear observables that are affected by an accumulation of effects throughout the implosion, which complicate interpretation of the data. A natural extension of these studies is therefore to conduct time-resolved measurements of multiple nuclear-burn histories to explore the dynamics of kinetic/multi-ion effects in the fuel and their impact on the implosion performance. This was accomplished through simultaneous, high-precision measurements of the relative timing of the onset, bang time and duration of DD, D3He, DT and T3He burn from T3He (with trace D) or D3He gas-filled implosions using the new Particle X-ray Temporal Diagnostic (PXTD) on OMEGA. As the different reactions have different temperature sensitivities, Ti(t) was determined from the data. Uniquely to the PXTD, several x-ray emission histories (in different energy bands) were also measured, from which a spatially averaged Te(t) was also determined. The inferred Ti(t) and Te(t) data have been used to experimentally explore ion-electron equilibration rates and the Coulomb Logarithm for various plasma conditions. Finally, the implementation and use of PXTD, which represents a significant advance at OMEGA, have laid the foundation for implementing a Te(t) measurement in support of the main cryogenic DT programs at OMEGA and the NIF. This work was supported in part by the US DOE, LLE, LLNL, and DOE NNSA SSGF.

Signals from Fat After Injury: Plasma Adipokines and Ghrelin Concentrations in the Severely Burned

DTIC Science & Technology

2012-09-26

of insulin resis- tance was calculated with a modified version of homeostasis mod- el assessment of insulin resistance ( HOMA - IR ) formula by using...average glucose and average circulating insulin levels of subjects. In this study, HOMA - IR was used to assess severity of insulin resis- tance rather than...were 217% higher than controls (Table 2). Thus, based on the HOMA - IR , burned subjects were more insulin resistant than controls (Table 2). As all of the

Linus cycle calculations including plasma transport and resistive flux loss in an incompressible liner

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quimby, D.C.; Hoffman, A.L.; Vlases, G.C.

1980-08-01

In the LINUS fusion reactor concept, a rotating liquid metal liner is used for reversible mechanical compression of thermonuclear plasmas, where a vacuum field buffer zone is used between the plasma and wall to reduce transport losses. A one-dimensional plasma transport and burn code, including incompressible liner dynamics with heat transfer and temperature dependent flux diffusion in the liquid metal, is used to model LINUS cycles. The effects of compressibility are treated as a perturbation. Numerical coefficients are derived for simple LINUS scaling laws. The particular case of plasma contact with the liquid metal is studied to determine the effectmore » on LINUS performance.« less

Results from the MARBLE Campaign on the National Ignition Facility: Implosion of Foam-Filled Capsules for Studying Thermonuclear Burn in the Presence of Heterogeneous Mix

NASA Astrophysics Data System (ADS)

Murphy, T. J.; Douglas, M. R.; Cardenas, T.; Devolder, B. G.; Fincke, J. R.; Gunderson, M. A.; Haines, B. M.; Hamilton, C. E.; Kim, Y. H.; Lee, M. N.; Oertel, J. A.; Olson, R. E.; Randolph, R. B.; Shah, R. C.; Smidt, J. M.

2016-10-01

The MARBLE campaign on NIF investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. MARBLE utilizes plastic capsules filled with deuterated plastic foam and tritium gas. The ratio of DT to DD neutron yield is indicative of the degree to which the foam and the gas atomically mix. Platform development experiments have been performed to understand the behavior of the foam and of the gas separately using two types of capsule. The first uses partially deuterated foam and hydrogen gas fill to understand the burn in the foam. The second uses undeuterated foam and deuterium gas fill to understand the dynamics of the gas. Experiments using deuterated foam and tritium gas are planned. Results of these experiments, and the implications for our understanding of thermonuclear burn in heterogeneously mixed separated reactant experiments will be discussed. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Nurses' perceptions and experiences regarding Morphine usage in burn pain management.

PubMed

Bayuo, J; Agbenorku, P

2015-06-01

Morphine, a classical example of opioid has been described as one of the analgesics of choice for burn pain management but there have been reports of under utilization of the medication and subsequent poor pain management. Nurses have a pivotal role in successful burn pain management and should therefore possess positive perception as well as strong knowledge base of pain care. In light of this realization, this study sought to investigate the perception and experiences of nurses working in the burns unit possess towards the medication. Purposive sampling approach was used to select twenty (20) nurses. Descriptive and themed content analysis approaches were used to analyze data. Mean years in general nursing practice and practice in the burns unit were obtained as 7.4 and 3.4 years respectively. Results indicate that nurses have a clear understanding of the intensity of burn pain but perception towards morphine was mixed and some respondents were unsure about some of the pertinent facts of morphine and thus, would prefer other medications such as paracetamol, diclofenac and pethidine. Addiction to the medication and morphine causing death were major themes identified. The resultant effect of these perception and experiences imply and confirm the under usage of morphine. It is therefore recommended that nurses within the burn unit be taken through training modules on the suitability of morphine in burn pain management. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

DIII-D research advancing the scientific basis for burning plasmas and fusion energy

NASA Astrophysics Data System (ADS)

W. M. SolomonThe DIII-D Team

2017-10-01

The DIII-D tokamak has addressed key issues to advance the physics basis for ITER and future steady-state fusion devices. In work related to transient control, magnetic probing is used to identify a decrease in ideal stability, providing a basis for active instability sensing. Improved understanding of 3D interactions is emerging, with RMP-ELM suppression correlated with exciting an edge current driven mode. Should rapid plasma termination be necessary, shattered neon pellet injection has been shown to be tunable to adjust radiation and current quench rate. For predictive simulations, reduced transport models such as TGLF have reproduced changes in confinement associated with electron heating. A new wide-pedestal variant of QH-mode has been discovered where increased edge transport is found to allow higher pedestal pressure. New dimensionless scaling experiments suggest an intrinsic torque comparable to the beam-driven torque on ITER. In steady-state-related research, complete ELM suppression has been achieved that is relatively insensitive to q 95, having a weak effect on the pedestal. Both high-q min and hybrid steady-state plasmas have avoided fast ion instabilities and achieved increased performance by control of the fast ion pressure gradient and magnetic shear, and use of external control tools such as ECH. In the boundary, experiments have demonstrated the impact of E× B drifts on divertor detachment and divertor asymmetries. Measurements in helium plasmas have found that the radiation shortfall can be eliminated provided the density near the X-point is used as a constraint in the modeling. Experiments conducted with toroidal rings of tungsten in the divertor have indicated that control of the strike-point flux is important for limiting the core contamination. Future improvements are planned to the facility to advance physics issues related to the boundary, transients and high performance steady-state operation.

DIII-D research advancing the scientific basis for burning plasmas and fusion energy

DOE PAGES

Solomon, Wayne M.

2017-07-12

The DIII-D tokamak has addressed key issues to advance the physics basis for ITER and future steady-state fusion devices. In work related to transient control, magnetic probing is used to identify a decrease in ideal stability, providing a basis for active instability sensing. Improved understanding of 3D interactions is emerging, with RMP-ELM suppression correlated with exciting an edge current driven mode. Should rapid plasma termination be necessary, shattered neon pellet injection has been shown to be tunable to adjust radiation and current quench rate. For predictive simulations, reduced transport models such as TGLF have reproduced changes in confinement associated withmore » electron heating. A new wide- pedestal variant of QH-mode has been discovered where increased edge transport is found to allow higher pedestal pressure. New dimensionless scaling experiments suggest an intrinsic torque comparable to the beam-driven torque on ITER. In steady-state-related research, complete ELM suppression has been achieved that is relatively insensitive to q 95, having a weak effect on the pedestal. Both high-q min and hybrid steady-state plasmas have avoided fast ion instabilities and achieved increased performance by control of the fast ion pressure gradient and magnetic shear, and use of external control tools such as ECH. In the boundary, experiments have demonstrated the impact of E × B drifts on divertor detachment and divertor asymmetries. Measurements in helium plasmas have found that the radiation shortfall can be eliminated provided the density near the X-point is used as a constraint in the modeling. Experiments conducted with toroidal rings of tungsten in the divertor have indicated that control of the strike-point flux is important for limiting the core contamination. In conclusion, future improvements are planned to the facility to advance physics issues related to the boundary, transients and high performance steady-state operation.« less

DIII-D research advancing the scientific basis for burning plasmas and fusion energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solomon, Wayne M.

The DIII-D tokamak has addressed key issues to advance the physics basis for ITER and future steady-state fusion devices. In work related to transient control, magnetic probing is used to identify a decrease in ideal stability, providing a basis for active instability sensing. Improved understanding of 3D interactions is emerging, with RMP-ELM suppression correlated with exciting an edge current driven mode. Should rapid plasma termination be necessary, shattered neon pellet injection has been shown to be tunable to adjust radiation and current quench rate. For predictive simulations, reduced transport models such as TGLF have reproduced changes in confinement associated withmore » electron heating. A new wide- pedestal variant of QH-mode has been discovered where increased edge transport is found to allow higher pedestal pressure. New dimensionless scaling experiments suggest an intrinsic torque comparable to the beam-driven torque on ITER. In steady-state-related research, complete ELM suppression has been achieved that is relatively insensitive to q 95, having a weak effect on the pedestal. Both high-q min and hybrid steady-state plasmas have avoided fast ion instabilities and achieved increased performance by control of the fast ion pressure gradient and magnetic shear, and use of external control tools such as ECH. In the boundary, experiments have demonstrated the impact of E × B drifts on divertor detachment and divertor asymmetries. Measurements in helium plasmas have found that the radiation shortfall can be eliminated provided the density near the X-point is used as a constraint in the modeling. Experiments conducted with toroidal rings of tungsten in the divertor have indicated that control of the strike-point flux is important for limiting the core contamination. In conclusion, future improvements are planned to the facility to advance physics issues related to the boundary, transients and high performance steady-state operation.« less

The physics of pulsed streamer discharge in high pressure air and applications to engine techonologies

NASA Astrophysics Data System (ADS)

Lin, Yung-Hsu

The goal of this dissertation is to study high pressure streamers in air and apply it to diesel engine technologies. Nanosecond scale pulsed high voltage discharges in air/fuel mixtures can generate radicals which in turn have been shown to improve combustion efficiency in gasoline fueled internal combustion engines. We are exploring the possibility to extend such transient plasma generation and expected radical species generation to the range of pressures encountered in compression-ignition (diesel) engines having compression ratios of ˜20:1, thereby improving lean burning efficiency and extending the range of lean combustion. At the beginning of this dissertation, research into streamer discharges is reviewed. Then, we conducted experiments of streamer propagation at high pressures, calculated the streamer velocity based on both optical and electrical measurements, and the similarity law was checked by analyzing the streamer velocity as a function of the reduced electric field, E/P. Our results showed that the similarity law is invalid, and an empirical scaling factor, E/√P, is obtained and verified by dimensional analysis. The equation derived from the dimensional analysis will be beneficial to proper electrode and pulse generator design for transient plasma assisted internal engine experiments. Along with the high pressure study, we applied such technique on diesel engine to improve the fuel efficiency and exhaust treatment. We observed a small effect of transient plasma on peak pressure, which implied that transient plasma has the capability to improve the fuel consumption. In addition, the NO can be reduced effectively by the same technique and the energy cost is 30 eV per NO molecule.

The effect of relativistic Compton scattering on thermonuclear burn of pure deuterium fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghasemizad, A.; Nazirzadeh, M.; Khanbabaei, B.

The relativistic effects of the Compton scattering on the thermonuclear burn-up of pure deuterium fuel in non-equilibrium plasma have been studied by four temperature (4T) theory. In the limit of low electron temperatures and photon energies, the nonrelativistic Compton scattering is valid and a convenient approximation, but in the high energy exchange rates between electrons and photons, is seen to break down. The deficiencies of the nonrelativistic approximation can be overcome by using the relativistic correction in the photons kinetic equation. In this research, we have utilized the four temperature (4T) theory to calculate the critical burn-up parameter for puremore » deuterium fuel, while the Compton scattering is considered as a relativistic phenomenon. It was shown that the measured critical burn-up parameter in ignition with relativistic Compton scattering is smaller than that of the parameter in the ignition with the nonrelativistic Compton scattering.« less

Burn Control Mechanisms in Tokamaks

NASA Astrophysics Data System (ADS)

Hill, M. A.; Stacey, W. M.

2015-11-01

Burn control and passive safety in accident scenarios will be an important design consideration in future tokamak reactors, in particular fusion-fission hybrid reactors, e.g. the Subcritical Advanced Burner Reactor. We are developing a burning plasma dynamics code to explore various aspects of burn control, with the intent to identify feedback mechanisms that would prevent power excursions. This code solves the coupled set of global density and temperature equations, using scaling relations from experimental fits. Predictions of densities and temperatures have been benchmarked against DIII-D data. We are examining several potential feedback mechanisms to limit power excursions: i) ion-orbit loss, ii) thermal instability density limits, iii) MHD instability limits, iv) the degradation of alpha-particle confinement, v) modifications to the radial current profile, vi) ``divertor choking'' and vii) Type 1 ELMs. Work supported by the US DOE under DE-FG02-00ER54538, DE-FC02-04ER54698.

The role of alternative therapy in the management of partial thickness burns of the face--experience with the use of moist exposed burn ointment (MEBO) compared with silver sulphadiazine.

PubMed

Ang, E S; Lee, S T; Gan, C S; See, P; Chan, Y H; Ng, L H; Machin, D

2000-01-01

Conventional management of partial thickness facial burn wounds includes the use of silver sulphadiazine dressings. Silver sulphadiazine forms an overlying slough that makes wound healing assessment difficult. Moist exposed burn ointment (MEBO) has been proposed as the ideal burn wound dressing both for burns of the face and other sites. Proponents of MEBO claim that it accelerates wound healing and results in scarless wound healing and at the same time reduce bacterial colonisation and the need for analgesics. We present here our experience with MEBO in the management of partial thickness burns of the face. One hundred and fifteen patients with partial thickness burns were randomly assigned to conventional treatment or MEBO. Out of this, 112 were analysed. Thirty-nine patients sustained facial burns; 17 received MEBO and 22 received silver sulphadiazine. Patients were followed up daily until the burn wounds were reduced by 75% of original body surface area (BSA). In patients with facial burns, MEBO was similar to silver sulphadiazine therapy with respect to rate of wound healing. Minimal slough was present over the wounds in MEBO-treated wounds resulting in clearer assessment of healing progression. Advantages of MEBO as compared to silver sulphadiazine in the management of partial thickness burns of the face include convenient change of dressing and easier assessment of healing progression. This suggests that MEBO is a useful alternative therapy for partial thickness burns of the face.

Early Career. Harnessing nanotechnology for fusion plasma-material interface research in an in-situ particle-surface interaction facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allain, Jean Paul

2014-08-08

This project consisted of fundamental and applied research of advanced in-situ particle-beam interactions with surfaces/interfaces to discover novel materials able to tolerate intense conditions at the plasma-material interface (PMI) in future fusion burning plasma devices. The project established a novel facility that is capable of not only characterizing new fusion nanomaterials but, more importantly probing and manipulating materials at the nanoscale while performing subsequent single-effect in-situ testing of their performance under simulated environments in fusion PMI.

Progress in preparing scenarios for operation of the International Thermonuclear Experimental Reactor

NASA Astrophysics Data System (ADS)

Sips, A. C. C.; Giruzzi, G.; Ide, S.; Kessel, C.; Luce, T. C.; Snipes, J. A.; Stober, J. K.

2015-02-01

The development of operating scenarios is one of the key issues in the research for ITER which aims to achieve a fusion gain (Q) of ˜10, while producing 500 MW of fusion power for ≥300 s. The ITER Research plan proposes a success oriented schedule starting in hydrogen and helium, to be followed by a nuclear operation phase with a rapid development towards Q ˜ 10 in deuterium/tritium. The Integrated Operation Scenarios Topical Group of the International Tokamak Physics Activity initiates joint activities among worldwide institutions and experiments to prepare ITER operation. Plasma formation studies report robust plasma breakdown in devices with metal walls over a wide range of conditions, while other experiments use an inclined EC launch angle at plasma formation to mimic the conditions in ITER. Simulations of the plasma burn-through predict that at least 4 MW of Electron Cyclotron heating (EC) assist would be required in ITER. For H-modes at q95 ˜ 3, many experiments have demonstrated operation with scaled parameters for the ITER baseline scenario at ne/nGW ˜ 0.85. Most experiments, however, obtain stable discharges at H98(y,2) ˜ 1.0 only for βN = 2.0-2.2. For the rampup in ITER, early X-point formation is recommended, allowing auxiliary heating to reduce the flux consumption. A range of plasma inductance (li(3)) can be obtained from 0.65 to 1.0, with the lowest values obtained in H-mode operation. For the rampdown, the plasma should stay diverted maintaining H-mode together with a reduction of the elongation from 1.85 to 1.4. Simulations show that the proposed rampup and rampdown schemes developed since 2007 are compatible with the present ITER design for the poloidal field coils. At 13-15 MA and densities down to ne/nGW ˜ 0.5, long pulse operation (>1000 s) in ITER is possible at Q ˜ 5, useful to provide neutron fluence for Test Blanket Module assessments. ITER scenario preparation in hydrogen and helium requires high input power (>50 MW). H-mode operation in helium may be possible at input powers above 35 MW at a toroidal field of 2.65 T, for studying H-modes and ELM mitigation. In hydrogen, H-mode operation is expected to be marginal, even at 2.65 T with 60 MW of input power. Simulation code benchmark studies using hybrid and steady state scenario parameters have proved to be a very challenging and lengthy task of testing suites of codes, consisting of tens of sophisticated modules. Nevertheless, the general basis of the modelling appears sound, with substantial consistency among codes developed by different groups. For a hybrid scenario at 12 MA, the code simulations give a range for Q = 6.5-8.3, using 30 MW neutral beam injection and 20 MW ICRH. For non-inductive operation at 7-9 MA, the simulation results show more variation. At high edge pedestal pressure (Tped ˜ 7 keV), the codes predict Q = 3.3-3.8 using 33 MW NB, 20 MW EC, and 20 MW ion cyclotron to demonstrate the feasibility of steady-state operation with the day-1 heating systems in ITER. Simulations using a lower edge pedestal temperature (˜3 keV) but improved core confinement obtain Q = 5-6.5, when ECCD is concentrated at mid-radius and ˜20 MW off-axis current drive (ECCD or LHCD) is added. Several issues remain to be studied, including plasmas with dominant electron heating, mitigation of transient heat loads integrated in scenario demonstrations and (burn) control simulations in ITER scenarios.

Deep sole burns in several participants in a traditional festival of the firewalking ceremony in Kee-lung, Taiwan--clinical experiences and prevention strategies.

PubMed

Chang, Shun-Cheng; Hsu, Chih-Kang; Tzeng, Yuan-Sheng; Teng, Shou-Cheng; Fu, Ju-Peng; Dai, Niann-Tzyy; Chen, Shyi-Gen; Chen, Tim-Mo; Feng, Chun-Che

2012-11-01

Firewalking is a common Taoist cleansing ceremony in Taiwan, but burns associated with the practice have rarely been reported. We analyzed the patients with plantar burns from one firewalking ceremony. In one firewalking ceremony, 12 Taoist disciples suffered from contact burns to the soles of their feet while walking over burning coals. Eight of them had at least second-degree burns over areas larger than 1% of their total body surface areas (TBSAs). The age, sex, medical history, date of injury, time taken to traverse the fire pit, depth and TBSA of the burns, treatment, length of stay, and outcome were recorded and analyzed. Deep, disseminated second- to third-degree burns were noted and healing took as long as three weeks in some patients. Because disseminated hypertrophic scars form after burns, the soles involved regain much of their tensile strength while walking. The patients experienced only a few difficulties in their daily lives three months after injury. From our experience treating patients with deep disseminated second- to third-degree plantar burns caused by firewalking, we conclude that they should be treated conservatively, with secondary healing rather than a skin graft. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

Parecoxib Reduces Systemic Inflammation and Acute Lung Injury in Burned Animals with Delayed Fluid Resuscitation

PubMed Central

Chong, Si Jack; Wu, Jian; Lu, Jia; Moochhala, Shabbir M.

2014-01-01

Burn injuries result in the release of proinflammatory mediators causing both local and systemic inflammation. Multiple organ dysfunctions secondary to systemic inflammation after severe burn contribute to adverse outcome, with the lungs being the first organ to fail. In this study, we evaluate the anti-inflammatory effects of Parecoxib, a parenteral COX-2 inhibitor, in a delayed fluid resuscitation burned rat model. Anaesthetized Sprague Dawley rats were inflicted with 45% total body surface area full-thickness scald burns and subsequently subjected to delayed resuscitation with Hartmann's solution. Parecoxib (0.1, 1.0, and 10 mg/kg) was delivered intramuscularly 20 min after injury followed by 12 h interval and the rats were sacrificed at 6 h, 24 h, and 48 h. Burn rats developed elevated blood cytokines, transaminase, creatinine, and increased lung MPO levels. Animals treated with 1 mg/kg Parecoxib showed significantly reduced plasma level of CINC-1, IL-6, PGEM, and lung MPO. Treatment of 1 mg/kg Parecoxib is shown to mitigate systemic and lung inflammation without significantly affecting other organs. At present, no specific therapeutic agent is available to attenuate the systemic inflammatory response secondary to burn injury. The results suggest that Parecoxib may have the potential to be used both as an analgesic and ameliorate the effects of lung injury following burn. PMID:24579056

Monitoring and treatment of coagulation abnormalities in burn patients. an international survey on current practices

PubMed Central

Lavrentieva, A.; Depetris, N.; Kaimakamis, E.; Berardino, M.; Stella, M.

2016-01-01

Summary The magnitude of coagulation abnormalities, and the definition and treatment of coagulopathy in burn patients are inadequately understood and continue to be discussed in the literature. We aimed to analyse physicians’ views on monitoring and treating coagulation abnormalities in burn patients. A total of 350 questionnaires were distributed electronically to burn ICU physicians. Participation was voluntary and anonymous. Responses were analysed electronically and comparisons were made according to the region of the ICU or the specialty of the physician. Of the 350 questionnaires distributed, 55 (15.7%) were returned. The majority of burn specialists consider sepsis-induced coagulopathy to be the most frequent coagulopathy in burn patients, and 74.5% declare that they do not use any specific definition/scoring system in their department to detect coagulopathy. The majority of specialists (70.8%) use standard coagulation tests. The most frequent indications for plasma transfusion are massive bleeding (32.8%) and Disseminated Intravascular Coagulation syndrome treatment (20%). The main specific factors reported in our study are cryoprecipitate (23.2%) and fibrinogen concentrate (18.9%). 21.1% of respondents state that they do not use any specific coagulation factor substitution in burn patients. Specific coagulation factor substitution is not a routine practice. The low response rate precludes the generalization of our results. PMID:28149244

Role of density gradient driven trapped electron mode turbulence in the H-mode inner core with electron heating

DOE PAGES

Ernst, D. R.; Burrell, K. H.; Guttenfelder, W.; ...

2016-05-10

In a series of DIII-D [J. L. Luxon, Nucl. Fusion 42 614 (2002)] low torque quiescent H-mode experiments show that density gradient driven TEM (DGTEM) turbulence dominates the inner core of H-Mode plasmas during strong electron cyclotron heating (ECH). By adding 3.4 MW ECH doubles T e/T i from 0.5 to 1.0, which halves the linear DGTEM critical density gradient, locally reducing density peaking, while transport in all channels displays extreme stiffness in the density gradient. This then suggests fusion -heating may degrade inner core confinement in H-Mode plasmas with moderate density peaking and low collisionality, with equal electron andmore » ion temperatures, key conditions expected in burning plasmas. Gyrokinetic simulations using GYRO [J. Candy and R. E. Waltz, J. Comp. Phys. 186 545 (2003)] (and GENE [F. Jenko et al., Phys. Plasmas 7, 1904 (2000)]) closely match not only particle, energy, and momentum fluxes, but also density fluctuation spectra from Doppler Backscattering (DBS), with and without ECH. Inner core DBS density fluctuations display discrete frequencies with adjacent toroidal mode numbers, which we identify as DGTEMs. GS2 [W. Dorland et al., Phys. Rev. Lett. 85 5579 (2000)] predictions show the DGTEM can be suppressed, to avoid degradation with electron heating, by broadening the current density profile to attain q 0 > q min > 1.« less

Improving the fuel economy of stoichiometrically fueled S.I. engines by means of EGR and enhanced ignition -- A comparison of gasoline, methanol and natural gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neame, G.R.; Gardiner, D.P.; Mallory, R.W.

1995-12-31

This paper describes an experimental study in which the potential for fuel economy improvements with EGR was investigated using an automotive V6 engine. Steady state engine dynamometer tests were run at 2,000 rpm and 200 kPa Brake Mean Effective Pressure (BMEP). The engine was fueled with gasoline, methanol or natural gas. Plasma jet ignition was evaluated as a means of improving EGR tolerance. EGR tolerance with methanol was found to be better than with gasoline, while natural gas showed the poorest EGR tolerance. Plasma jet ignition extended EGR limits for all three fuels. Fuel economy benefits were realized with naturalmore » gas and gasoline at low EGR rates and without EGR but plasma jet ignition provided no improvements with methanol until over 10% EGR was used. Plasma jet ignition made stable operation possible with methanol at 40% EGR, where fuel economy improvements were ultimately limited by the slow burning associated with the high EGR rate. Both slow burning and high cyclic variation affected gasoline at high EGR rates, while stability limits to spark advance with natural gas caused fuel economy to degrade at relatively low EGR rates.« less

Addendum to High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Tan, N

2010-11-08

As part of a small follow-on study, the burn rate of the ammonium perchlorate (AP) based material TAL-1503 was studied at a relatively mild pressure. The goal of this final experiment was to burn TAL-1503 at the lowest pressures possible using the LLNL High Pressure Strand Burner (LLNL-HPSB). The following is a description of the experiment and the results with a brief discussion of data and a comparison to the higher pressure data. This is not meant to be a stand-alone report and readers should refer to the main report for experimental details and discussion. High pressure deflagration rate measurementsmore » of a unique AP/HTPB based material (TAL-1503) were performed using the LLNL high pressure strand burner apparatus. The material burns in a well behaved, laminar fashion between 20 and 300 MPa with a burn law of B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} that was calculated based on the best data available from the experiments. In the pressure range of 2 and 10 MPa the material burned laminarly with a burn law of B = (2.0 {+-} 0.2) x P{sup (0.66{+-}0.05)}. In these results, B is the burn rate in mm/s and P is the pressure in units of MPa. Comparison of the TAL-1503 results with similar propellants that contain micrometer sized aluminum indicate that the burn rates are relatively unaffected by the aluminum. However, the pressure change is significantly larger when aluminum is present, most likely due to the high temperatures achieved from burning aluminum.« less

Present Status and Prospects of FIREX Project

NASA Astrophysics Data System (ADS)

Mima, K.

2008-07-01

The goal of the first phase of Fast Ignition Realization EXperiment (FIREX) project (FIREX-I) is to demonstrate ignition temperature of 5-10 keV, followed by the second phase to demonstrate ignition and burn. Since starting FIREX-I project, plasma physics study in ILE has been devoted to increase the coupling efficiency and to improve compression performance. The heating efficiency can be increased by the following two ways. 1) A previous experiments indicate that the coupling of heating laser to imploded plasmas increases with coating a low-density. foam used in the experiment, low-Z plastic foam is desired for efficient electron transport. (Lei et al. 2006). 2) Electrons generated in the inner surface of the double cone will return by sheathe potential generated between two cones. A 2-D PIC simulation indicates that hot electron confinement is improved by a factor of 1.7 (Nakamura et al. 2007). Further optimization of cone geometry by 2-D simulation will be presented in the workshop. The implosion performance can be improved by three ways. 1) Low-Z plastic layer coating on the outer surface of the cone: The 2D hydro-simulation PINOCO predicts that the target areal density increases by a factor of 2. 2) Br doped plastic layer on a fuel pellet may significantly moderate the Rayleigh-Taylor instability (Fujioka et al. 2004), making implosion more stable. 3) Reducing vapor gas pressure in a pellet is necessary to suppress strength of a jet that will destroy the cone tip. (Stephens et al. 2005). As for the cryogenic target fabrication, R&D of fabricating foam cryogenic cine shell target are under development by the joint group between Osaka Univ. and NIFS. The amplifier system of the heating laser LFEX is completed in March 2008. The amplification test has demonstrated laser energy of 3 kJ/beam at 3nm bandwidth. The equivalent 12 kJ in 4 beams meets the specification of LFEX. The large tiled gratings for pulse compressor are completed and installed. The short pulse laser will be delivered on a target in September, 2008. The fully integrated fast ignition experiments is scheduled on February 2009 until the end of 2010. If subsequent FIREX-II will start as proposed, the ignition and burn will be demonstrated in parallel to that at NIF and LMJ, providing a scientific database of both central and fast ignition.

Optimizing implosion yields using rugby-shaped hohlraums

NASA Astrophysics Data System (ADS)

Park, Hye-Sook; Robey, H.; Amendt, P.; Philippe, F.; Casner, A.; Caillaud, T.; Bourgade, J.-L.; Landoas, O.; Li, C. K.; Petrasso, R.; Seguin, F.; Rosenberg, M.; Glebov, V. Yu.

2009-11-01

We present the first experimental results on optimizing capsule implosion experiments by using rugby-shaped hohlraums [1] on the Omega laser, University of Rochester. This campaign compared D2-filled capsule performance between standard cylindrical Au hohlraums and rugby-shaped hohlraums for demonstrating the energetics advantages of the rugby geometry. Not only did the rugby-shaped hohlraums show nearly 20% more x-ray drive energy over the cylindrical hohlraums, but also the high-performance design of the capsules provided nearly 20 times more DD neutrons than in any previous Omega hohlraum campaigns, thereby enabling use of neutron temporal diagnostics. Comparison with simulations on neutron burn histories, x-ray core imaging, backscattered laser light and radiation temperature are presented. [1] P. Amendt et al., Phys. Plasmas 15, 012702 (2008)

Plasma chemistry of NO in complex gas mixtures excited with a surfatron launcher.

PubMed

Hueso, J L; González-Elipe, A R; Cotrino, J; Caballero, A

2005-06-09

The plasma chemistry of NO has been investigated in gas mixtures with oxygen and/or hydrocarbon and Ar as carrier gas. Surface wave discharges operating at microwave frequencies have been used for this study. The different plasma reactions have been analyzed for a pressure range between 30 and 75 Torr. Differences in product concentration and/or reaction yields smaller than 10% were found as a function of this parameter. The following gas mixtures have been considered for investigation: Ar/NO, Ar/NO/O2, Ar/NO/CH4, Ar/CH4/O2, Ar/NO/CH4/O2. It is found that NO decomposes into N2 and O2, whereas other products such as CO, H2, and H2O are also formed when CH4 and O2 are present in the reaction mixture. Depending on the working conditions, other minority products such as HCN, CO2, and C2 or higher hydrocarbons have been also detected. The reaction of an Ar/NO plasma with deposits of solid carbon has also been studied. The experiments have provided useful information with respect to the possible removal of soot particles by this type of plasma. It has been shown that carbon deposits are progressively burned off by interaction with the plasma, and practically 100% decomposition of NO was found. Plasma intermediate species have been studied by optical emission spectroscopy (OES). Bands and/or peaks due to N2*, NO*, OH*, C2*, CN*, CH*, or H* were detected with different relative intensities depending on the gas mixture. From the analysis of both the reaction products and efficiency and the type of intermediate species detected by OES, different plasma reactions and processes are proposed to describe the plasma chemistry of NO in each particular mixture of gases. The results obtained provide interesting insights about the plasma removal of NO in real gas exhausts.

Neuromuscular pharmacodynamics of mivacurium in adults with major burns.

PubMed

Han, T-H; Martyn, J A J

2011-05-01

Mivacurium is metabolized by plasma pseudocholinesterase (PChE) enzyme, which is decreased in burns. We tested whether the decreased metabolism of mivacurium due to decreased PChE activity can overcome the pharmacodynamic resistance to non-depolarizing relaxants previously seen in major burns. Thirty adults with 35 (13)% [mean (sd)] burn were studied at 5-91 post-burn days and 31 non-burns matched controls. Mivacurium 0.2 mg kg(-1) was administered as a single bolus. Neuromuscular block was monitored with single-twitch response using TOF-Watch™. Onset time (drug administration to maximal twitch suppression) and spontaneous recovery were measured. Onset time was significantly prolonged in burns when compared with non-burns (115 vs 90 s; P<0.001). The PChE levels were lower in burns [1432 (916) vs 2866 (731) IU litre(-1); P<0.001] and the neuromuscular recovery to 50% of baseline twitch height was prolonged in burns (41 vs 26 min; P<0.001). There was a significant correlation between PChE and time to 50% recovery for the whole group together (r=-0.6; P<0.001). The dibucaine numbers were not different. The prolonged onset time suggests resistance to neuromuscular effects, whereas the prolonged recovery suggests increased sensitivity. This divergent response can be explained by qualitative and quantitative changes in acetylcholine receptor expression causing resistance and decreased PChE activity causing sensitivity. Despite using a relatively large dose of mivacurium (0.2 mg kg(-1)) in the presence of decreased PChE levels, this did not overcome the resistance resulting from up-regulated receptors.

Progress in Fast Ignition Studies with Electrons and Protons

NASA Astrophysics Data System (ADS)

MacKinnon, A. J.; Akli, K. U.; Bartal, T.; Beg, F. N.; Chawla, S.; Chen, C. D.; Chen, H.; Chen, S.; Chowdhury, E.; Fedosejevs, R.; Freeman, R. R.; Hey, D.; Higginson, D.; Key, M. H.; King, J. A.; Link, A.; Ma, T.; MacPhee, A. G.; Offermann, D.; Ovchinnikov, V.; Pasley, J.; Patel, P. K.; Ping, Y.; Schumacher, D. W.; Stephens, R. B.; Tsui, Y. Y.; Wei, M. S.; Van Woerkom, L. D.

2009-09-01

Isochoric heating of inertially confined fusion plasmas by laser driven MeV electrons or protons is an area of great topical interest in the inertial confinement fusion community, particularly with respect to the fast ignition (FI) concept for initiating burn in a fusion capsule. In order to investigate critical aspects needed for a FI point design, experiments were performed to study 1) laser-to-electrons or protons conversion issues and 2) laser-cone interactions including prepulse effects. A large suite of diagnostics was utilized to study these important parameters. Using cone—wire surrogate targets it is found that pre-pulse levels on medium scale lasers such as Titan at Lawrence Livermore National Laboratory produce long scale length plasmas that strongly effect coupling of the laser to FI relevant electrons inside cones. The cone wall thickness also affects coupling to the wire. Conversion efficiency to protons has also been measured and modeled as a function of target thickness, material. Conclusions from the proton and electron source experiments will be presented. Recent advances in modeling electron transport and innovative target designs for reducing igniter energy and increasing gain curves will also be discussed. In conclusion, a program of study will be presented based on understanding the fundamental physics of the electron or proton source relevant to FI.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stencel, J.R.; Finley, V.L.

This report gives the results of the environmental activities and monitoring programs at the Princeton Plasma Physics Laboratory for CY90. The report is prepared to provide the US Department of Energy (DOE) and the public with information on the level of radioactive and nonradioactive pollutants, if any, added to the environment as a result of PPPL operations, as well as environmental initiatives, assessments, and programs. The objective of the Annual Site Environmental Report is to document evidence that DOE facility environmental protection programs adequately protect the environment and the public health. The PPPL has engaged in fusion energy research sincemore » 1951 and in 1990 had one of its two large tokamak devices in operation: namely, the Tokamak Fusion Test Reactor. The Princeton Beta Experiment-Modification is undergoing new modifications and upgrades for future operation. A new machine, the Burning Plasma Experiment -- formerly called the Compact Ignition Tokamak -- is under conceptual design, and it is awaiting the approval of its draft Environmental Assessment report by DOE Headquarters. This report is required under the National Environmental Policy Act. The long-range goal of the US Magnetic Fusion Energy Research Program is to develop and demonstrate the practical application of fusion power as an alternate energy source. 59 refs., 39 figs., 45 tabs.« less

Nondiffusive transport regimes for suprathermal ions in turbulent plasmas

NASA Astrophysics Data System (ADS)

Bovet, A.; Fasoli, A.; Ricci, P.; Furno, I.; Gustafson, K.

2015-04-01

The understanding of the transport of suprathermal ions in the presence of turbulence is important for fusion plasmas in the burning regime that will characterize reactors, and for space plasmas to understand the physics of particle acceleration. Here, three-dimensional measurements of a suprathermal ion beam in the toroidal plasma device TORPEX are presented. These measurements demonstrate, in a turbulent plasma, the existence of subdiffusive and superdiffusive transport of suprathermal ions, depending on their energy. This result stems from the unprecedented combination of uniquely resolved measurements and first-principles numerical simulations that reveal the mechanisms responsible for the nondiffusive transport. The transport regime is determined by the interaction of the suprathermal ion orbits with the turbulent plasma dynamics, and is strongly affected by the ratio of the suprathermal ion energy to the background plasma temperature.

Fully non-inductive second harmonic electron cyclotron plasma ramp-up in the QUEST spherical tokamak

NASA Astrophysics Data System (ADS)

Idei, H.; Kariya, T.; Imai, T.; Mishra, K.; Onchi, T.; Watanabe, O.; Zushi, H.; Hanada, K.; Qian, J.; Ejiri, A.; Alam, M. M.; Nakamura, K.; Fujisawa, A.; Nagashima, Y.; Hasegawa, M.; Matsuoka, K.; Fukuyama, A.; Kubo, S.; Shimozuma, T.; Yoshikawa, M.; Sakamoto, M.; Kawasaki, S.; Nakashima, H.; Higashijima, A.; Ide, S.; Maekawa, T.; Takase, Y.; Toi, K.

2017-12-01

Fully non-inductive second (2nd) harmonic electron cyclotron (EC) plasma current ramp-up was demonstrated with a newlly developed 28 GHz system in the QUEST spherical tokamak. A high plasma current of 54 kA was non-inductively ramped up and sustained stably for 0.9 s with a 270 kW 28 GHz wave. A higher plasma current of 66 kA was also non-inductively achieved with a slow ramp-up of the vertical field. We have achieved a significantly higher plasma current than those achieved previously with the 2nd harmonic EC waves. This fully non-inductive 2nd harmonic EC plasma ramp-up method might be useful for future burning plasma devices and fusion reactors, in particular for operations at half magnetic field with the same EC heating equipment.

Analysis of recurrent patterns in toroidal magnetic fields.

PubMed

Sanderson, Allen R; Chen, Guoning; Tricoche, Xavier; Pugmire, David; Kruger, Scott; Breslau, Joshua

2010-01-01

In the development of magnetic confinement fusion which will potentially be a future source for low cost power, physicists must be able to analyze the magnetic field that confines the burning plasma. While the magnetic field can be described as a vector field, traditional techniques for analyzing the field's topology cannot be used because of its Hamiltonian nature. In this paper we describe a technique developed as a collaboration between physicists and computer scientists that determines the topology of a toroidal magnetic field using fieldlines with near minimal lengths. More specifically, we analyze the Poincaré map of the sampled fieldlines in a Poincaré section including identifying critical points and other topological features of interest to physicists. The technique has been deployed into an interactive parallel visualization tool which physicists are using to gain new insight into simulations of magnetically confined burning plasmas.

Impact of temperature-velocity distribution on fusion neutron peak shape

DOE PAGES

Munro, D. H.; Field, J. E.; Hatarik, R.; ...

2017-02-21

Doppler broadening of the 14 MeV DT and 2.45 MeV DD fusion neutron lines has long been our best measure of temperature in a burning plasma. At the National Ignition Facility (NIF), yields are high enough and our neutron spectrometers accurate enough that we see finer details of the peak shape. For example, we can measure the shift of the peak due to the bulk motion of the plasma, and we see indications of non-thermal broadening, skew, and kurtosis of the peak caused by the variations of temperature and fluid velocity during burn. We can also distinguish spectral differences amongmore » several lines of sight. Finally, this paper will review the theory of fusion neutron line shape, show examples of non-Gaussian line shapes and directional variations in NIF data, and describe detailed spectral shapes we see in radiation-hydrodynamics simulations of implosions.« less

Impact of temperature-velocity distribution on fusion neutron peak shape

NASA Astrophysics Data System (ADS)

Munro, D. H.; Field, J. E.; Hatarik, R.; Peterson, J. L.; Hartouni, E. P.; Spears, B. K.; Kilkenny, J. D.

2017-05-01

Doppler broadening of the 14 MeV DT and 2.45 MeV DD fusion neutron lines has long been our best measure of temperature in a burning plasma. At the National Ignition Facility (NIF), yields are high enough and our neutron spectrometers accurate enough that we see finer details of the peak shape. For example, we can measure the shift of the peak due to the bulk motion of the plasma, and we see indications of non-thermal broadening, skew, and kurtosis of the peak caused by the variations of temperature and fluid velocity during burn. We can also distinguish spectral differences among several lines of sight. This paper will review the theory of fusion neutron line shape, show examples of non-Gaussian line shapes and directional variations in NIF data, and describe detailed spectral shapes we see in radiation-hydrodynamics simulations of implosions.

Alpha particle effects in burning tokamak plasmas: overview and specific examples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigmar, D.J.

1986-07-01

Using the total power balance of an ignited tokamak plasma as a guideline, a range of alpha driven effects is surveyed regarding their impact on achieving and maintaining fusion burn. Specific examples of MHD and kinetic modes and multi species transport dynamics are discussed, including the possible interaction of these categories of effects. This power balance approach rather than a straightforward enumeration of possible effects serves to reveal their non-linear dependence and the ensuing fragility of our understanding of the approach to and maintenance of ignition. Specific examples are given of the interaction between ..cap alpha..-power driven sawtoothing and idealmore » MHD stability, and direct ..cap alpha..-effects on MHD modes including kinetic corrections. Anomalous ion heat transport and central impurity peaking mechanisms and anomalous and collisional ..cap alpha..-transport including the ambipolar electric field are discussed.« less

Physics of Alfvén waves and energetic particles in burning plasmas

NASA Astrophysics Data System (ADS)

Chen, Liu; Zonca, Fulvio

2016-01-01

Dynamics of shear Alfvén waves and energetic particles are crucial to the performance of burning fusion plasmas. This article reviews linear as well as nonlinear physics of shear Alfvén waves and their self-consistent interaction with energetic particles in tokamak fusion devices. More specifically, the review on the linear physics deals with wave spectral properties and collective excitations by energetic particles via wave-particle resonances. The nonlinear physics deals with nonlinear wave-wave interactions as well as nonlinear wave-energetic particle interactions. Both linear as well as nonlinear physics demonstrate the qualitatively important roles played by realistic equilibrium nonuniformities, magnetic field geometries, and the specific radial mode structures in determining the instability evolution, saturation, and, ultimately, energetic-particle transport. These topics are presented within a single unified theoretical framework, where experimental observations and numerical simulation results are referred to elucidate concepts and physics processes.

A ten-year experience with hemodialysis in burn patients at Los Angeles County + USC Medical Center.

PubMed

Soltani, Ali; Karsidag, Semra; Garner, Warren

2009-01-01

Acute renal failure (ARF) is a rare, but serious, complication after burn injury that is commonly thought to be fatal. Before the modern era, there were few survivors of burn injuries who required dialysis. We report our 10-year experience with ARF and dialysis at the Los Angeles County + USC burn unit. During the period of August 1994 to February 2004, 3356 patients were admitted. Furthermore, 1143 patients were admitted to the intensive care unit and 1125 had burns >10% TBSA. Thirty-three patients developed ARF necessitating dialysis, equaling 0.98% of all admitted patients, and 2.7% of patients with TBSA >10% burns, which is at the low end of published burn unit data. The average age of these patients requiring dialysis was 49 years, 91% were men, 24% were diabetic, and 39% were positive for substances of abuse at admission, and the average TBSA burned was 36%. This is compared with an average age of 31 years, 70% men, 7.3% diabetic, and 14.7% intoxicated in the general burned population at our burn unit. Furthermore, our overall mortality in the burn unit was 5% overall and 14% in patients with >10% TBSA burns during the study period. In patients requiring hemodialysis, the mortality rate was 69.7%. The average time to hemodialysis was 14 days in our series, and patients, on average, required 10.3 days of dialysis support. These mortality data are the lowest recorded for burned patients requiring dialysis and suggest that ARF is a survivable complication in some of these patients.

Towards self-consistent plasma modelisation in presence of neoclassical tearing mode and sawteeth: effects on transport coefficients

NASA Astrophysics Data System (ADS)

Basiuk, V.; Huynh, P.; Merle, A.; Nowak, S.; Sauter, O.; Contributors, JET; the EUROfusion-IM Team

2017-12-01

The neoclassical tearing modes (NTM) increase the effective heat and particle radial transport inside the plasma, leading to a flattening of the electron and ion temperature and density profiles at a given location depending on the safety factor q rational surface (Hegna and Callen 1997 Phys. Plasmas 4 2940). In burning plasma such as in ITER, this NTM-induced increased transport could reduce significantly the fusion performance and even lead to a disruption. Validating models describing the NTM-induced transport in present experiment is thus important to help quantifying this effect on future devices. In this work, we apply an NTM model to an integrated simulation of current, heat and particle transport on JET discharges using the European transport simulator. In this model, the heat and particle radial transport coefficients are modified by a Gaussian function locally centered at the NTM position and characterized by a full width proportional to the island size through a constant parameter adapted to obtain the best simulations of experimental profiles. In the simulation, the NTM model is turned on at the same time as the mode is triggered in the experiment. The island evolution is itself determined by the modified Rutherford equation, using self-consistent plasma parameters determined by the transport evolution. The achieved simulation reproduces the experimental measurements within the error bars, before and during the NTM. A small discrepancy is observed on the radial location of the island due to a shift of the position of the computed q = 3/2 surface compared to the experimental one. To explain such small shift (up to about 12% with respect to the position observed from the experimental electron temperature profiles), sensitivity studies of the NTM location as a function of the initialization parameters are presented. First results validate both the transport model and the transport modification calculated by the NTM model.

Scaling of Liquid DT Layer Capsules to an ICF Burning Plasma

NASA Astrophysics Data System (ADS)

Olson, R. E.; Peterson, R. R.; Haines, B. M.; Yi, S. A.; Bradley, P. A.; Zylstra, A. B.; Kline, J. L.; Leeper, R. J.; Batha, S. H.

2017-10-01

Recent experiments at the NIF demonstrated cryogenic liquid DT layer ICF implosions. Unlike DT ice layer implosions, DT liquid layer designs can operate with low-to-moderate convergence ratio (12

Thermomagnetic burn control for magnetic fusion reactor

DOEpatents

Rawls, J.M.; Peuron, A.U.

1980-07-01

Apparatus is provided for controlling the plasma energy production rate of a magnetic-confinement fusion reactor, by controlling the magnetic field ripple. The apparatus includes a group of shield sectors formed of ferromagnetic material which has a temperature-dependent saturation magnetization, with each shield lying between the plasma and a toroidal field coil. A mechanism for controlling the temperature of the magnetic shields, as by controlling the flow of cooling water therethrough, thereby controls the saturation magnetization of the shields and therefore the amount of ripple in the magnetic field that confines the plasma, to thereby control the amount of heat loss from the plasma. This heat loss in turn determines the plasma state and thus the rate of energy production.

Wood crib fire free burning test in ISO room

NASA Astrophysics Data System (ADS)

Qiang, Xu; Griffin, Greg; Bradbury, Glenn; Dowling, Vince

2006-04-01

In the research of application potential of water mist fire suppression system for fire fighting in train luggage carriage, a series of experiments were conducted in ISO room on wood crib fire with and without water mist actuation. The results of free burn test without water mist suppression are used as reference in evaluating the efficiency of water mist suppression system. As part of the free burn test, several tests have been done under the hood of ISO room to calibrate the size of the crib fire and these tests can also be used in analyzing the wall effect in room fire hazard. In these free burning experiments, wood cribs of four sizes under the hood were tested. The temperature of crib fire, heat flux around the fire, gas concentration in hood of ISO room were measured in the experiments and two sets of thermal imaging system were used to get the temperature distribution and the typical shape of the free burning flames. From the experiments, the radiation intensity in specific positions around the fire, the effective heat of combustion, mass loss, oxygen consumption rate for different sizes of fire, typical structure of the flame and self extinguishment time was obtained for each crib size.

Formation of Imploding Plasma Liners for HEDP and MIF Application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witherspoon, F. Douglas; Case, Andrew; Brockington, Samuel

Plasma jets with high density and velocity have a number of important applications in fusion energy and elsewhere, including plasma refueling, disruption mitigation in tokamaks, magnetized target fusion, injection of momentum into centrifugally confined mirrors, plasma thrusters, and high energy density plasmas (HEDP). In Magneto-Inertial Fusion (MIF), for example, an imploding material liner is used to compress a magnetized plasma to fusion conditions and to confine the resulting burning plasma inertially to obtain the necessary energy gain. The imploding shell may be solid, liquid, gaseous, or a combination of these states. The presence of the magnetic field in the targetmore » plasma suppresses thermal transport to the plasma shell, thus lowering the imploding power needed to compress the target to fusion conditions. This allows the required imploding momentum flux to be generated electromagnetically using off-the-shelf pulsed power technology. Practical schemes for standoff delivery of the imploding momentum flux are required and are open topics for research. One approach for accomplishing this, called plasma jet driven magneto-inertial fusion (PJMIF), uses a spherical array of pulsed plasma guns to create a spherically imploding shell of very high velocity, high momentum flux plasma. This approach requires development of plasma jet accelerators capable of achieving velocities of 50-200 km/s with very precise timing and density profiles, and with high total mass and density. Low-Z plasma jets would require the higher velocities, whereas very dense high-Z plasma shells could achieve the goal at velocities of only 50-100 km/s. In this report, we describe our work to develop the pulsed plasma gun technology needed for an experimental scientific exploration of the PJMIF concept, and also for the other applications mentioned earlier. The initial goal of a few hundred of hydrogen at 200 km/s was eventually replaced with accelerating 8000 μg of argon or xenon to 50 km/s for the Plasma Liner Experiment (PLX) at Los Alamos National Laboratory (LANL). Initial work used existing computational and analytical tools to develop and refine a specific plasma gun concept having a novel tapered coaxial electromagnetic accelerator contour with an array of symmetric ablative plasma injectors. The profile is designed to suppress the main barrier to success in coaxial guns, namely the blow-by instability in which the arc slips past and outruns the bulk of the plasma mass. Efforts to begin developing a set of annular non-ablative plasma injectors for the coaxial gun, in order to accelerate pure gases, resulted in development of linear parallel-plate MiniRailguns that turned out to work well as plasma guns in their own right and we subsequently chose them for an initial plasma liner experiment on the PLX facility at LANL. This choice was mainly driven by cost and schedule for that particular experiment, while longer term goals still projected use of coaxial guns for reactor-relevant applications for reasons of better symmetry, lower impurities, more compact plasma jet formation, and higher gun efficiency. Our efforts have focused mainly on 1) developing various plasma injection systems for both coax and linear railguns and ensuring they work reliably with the accelerator section, 2) developing a suite of plasma and gun diagnostics, 3) performing computational modeling to design and refine the plasma guns, 4) establishing a research facility dedicated to plasma gun development, and finally, 5) developing plasma guns and associated pulse power systems capable of achieving these goals and installing and testing the first two gun sets on the PLX facility at LANL. During the second funding cycle for this program, HyperV joined in a collaborative effort with LANL, the University of Alabama at Huntsville, and the University of New Mexico to perform a plasma liner experiment (PLX) to investigate the physics and technology of forming spherically imploding plasma liners. HyperV’s tasks focused on developing the plasma guns and associated pulse power systems required for the 30 gun experiment at LANL. Unfortunately, funding for the entire PLX collaborative project was terminated after only two years of the four year project due to program funding realignments which necessitated recompeting the project in midstream. Despite the loss of funding, HyperV installed two Mark1 guns and pulsed power systems on PLX, and jet characterization and merging experiments were subsequently successfully performed at LANL by the PLX Team. In parallel with those PLX experiments, HyperV continued its efforts to develop a plasma gun capable of meeting the PLX goal of 8 mg of argon at 50 km/s. HyperV was ultimately successful in this effort, demonstrating 10.8 mg at 52.8 km/s and 7.5 mg at 62.4 km/s with the Mark2 MiniRailgun.« less

A lateral tarsorrhaphy with forehead hitch to pre-empt and treat burns ectropion with a contextual review of burns ectropion management.

PubMed

Lymperopoulos, Nikolaos S; Jordan, Daniel J; Jeevan, Ranjeet; Shokrollahi, Kayvan

2016-01-01

Facial burns around the eyes and eyelid ectropion can lead to corneal exposure, irritation, dryness, epiphora, infection or visual loss. We undertook a review of the published articles describing management of eyelid burns as well as methods to treat or prevent ectropion. We describe early experience of a surgical technique that we have found to mitigate ectropion in facial burns with peri-ocular involvement. Two illustrative cases with our surgical technique is described from our experience of three cases. We reviewed the literature using the PubMed and EMBASE databases using the search terms 'burn' and 'ectropion'. The literature review produced a total of 17 relevant papers. Treatment options for eyelid burns were varied and were invariably level 4 or 5 evidence. Various techniques were used to treat eyelid burns including the use of a full thickness skin graft with or without concurrent scar contracture release but also use of a local flap reconstruction with or without a tissue expander or release of the underlying muscle. Other techniques included canthoplasty, Z-plasty, forehead flaps, fat transfer, and tarsorrhaphy with full thickness skin grafting. In general, the focus of articles was therapeutic and reconstructive rather than pre-emptive/preventative management. We describe our early experience of a novel technique for temporary lateral tarsorrhaphy with forehead hitch which protexts the globe and counters the scar- and gravity-related ectropic effects on the lower eyelids. Facial burns pose a difficult problem to the burn surgeon, especially when the eyelids are affected, both directly or indirectly. The optimal surgical management of eyelid burns remains unclear and the literature base lies mainly in the domain of case series. We review the literature on this subject and tabulate our findings and also describe our contribution to this area with a method of lateral and lower lid elevator that we have found valuable.

High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glascoe, E A; Tan, N

2010-04-21

High pressure deflagration rate measurements of a unique ammonium perchlorate (AP) based propellant are required to design the base burn motor for a Raytheon weapon system. The results of these deflagration rate measurements will be key in assessing safety and performance of the system. In particular, the system may experience transient pressures on the order of 100's of MPa (10's kPSI). Previous studies on similar AP based materials demonstrate that low pressure (e.g. P < 10 MPa or 1500 PSI) burn rates can be quite different than the elevated pressure deflagration rate measurements (see References and HPP results discussed herein),more » hence elevated pressure measurements are necessary in order understand the deflagration behavior under relevant conditions. Previous work on explosives have shown that at 100's of MPa some explosives will transition from a laminar burn mechanism to a convective burn mechanism in a process termed deconsolidative burning. The resulting burn rates that are orders-of-magnitude faster than the laminar burn rates. Materials that transition to the deconsolidative-convective burn mechanism at elevated pressures have been shown to be considerably more violent in confined heating experiments (i.e. cook-off scenarios). The mechanisms of propellant and explosive deflagration are extremely complex and include both chemical, and mechanical processes, hence predicting the behavior and rate of a novel material or formulation is difficult if not impossible. In this work, the AP/HTPB based material, TAL-1503 (B-2049), was burned in a constant volume apparatus in argon up to 300 MPa (ca. 44 kPSI). The burn rate and pressure were measured in-situ and used to calculate a pressure dependent burn rate. In general, the material appears to burn in a laminar fashion at these elevated pressures. The experiment was reproduced multiple times and the burn rate law using the best data is B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} where B is the burn rate in mm/s and P is the pressure in units of MPa. Details of the experimental method, results and data analysis are discussed herein and briefly compared to other AP based materials that have been measured in this apparatus.« less

Effects of seasonal prescribved fires on residual overstory trees in oak-dominate shelterwood stands

Treesearch

Patrick H. Brose; David H. Van Lear

1999-01-01

A study was initiated in 1994 to evaluate the degree of bole damage and crown decline residual overstory trees would experience because of prescribed burning of shelterwood stands. Three oak-dominated shelterwood stands, partially harvested 2 to 4 yr earlier, were divided into four treatments (unburned control, spring burn, summer burn, and winter burn). Fifteen...

Impacts of Growing-Season Prescibed Burns in the Florida Pine Flatwoods Type

Treesearch

Kenneth W. Outcalt; John L. Foltz

2004-01-01

A considerable amount of experience and knowledge has been gained in the application of growing-season burning in pine communities across the Southeast. However, there is still concern that burning during this season will cause increased tree mortality and/or growth loss. Pine flatwoods stands in south Florida with 3 years of fuel accumulation were burned during the...

Changes to oak woodland stand structure and ground flora composition caused by thinning and burning

Treesearch

Carter O. Kinkead; John M. Kabrick; Michael C. Stambaugh; Keith W. Grabner

2013-01-01

Our objective was to quantify the cumulative effects of prescribed burning and thinning on forest stocking and species composition at a woodland restoration experiment site in the Ozark Highlands of Missouri. Our study used four treatments (burn, harvest, harvest and burn, control) on three slope position and aspect combinations (south, north, ridge) replicated in...

Arnica and stinging nettle for treating burns - a self-experiment.

PubMed

Huber, Roman; Bross, Felix; Schempp, Christoph; Gründemann, Carsten

2011-10-01

Combudoron, composed of extracts from arnica and stinging nettle, is used for the treatment of partial thickness burns and insect bites in Europe. Because clinical investigations are lacking we wanted to investigate its efficacy in partial thickness burns. Two individuals performed a self experiment: 4 experimental grade 2 burns (each 1 cm(2)) on the back were induced respectively with an erbium YAG-laser. Wounds were treated with Combudoron gel, Combudoron liquid, placebo gel or placebo liquid in each of the subjects in a standardized, single blind manner. Outcome parameters were the photo documented duration of wound healing and visual analogue scale (VAS) pain scores. All 8 experimental burns were similar from size and depth at baseline. Eschars of the verum-treated burns fell off earlier than the placebo-treated burns (verum liquid: after 14 and 19 days compared to 17 and 27 days with placebo liquid. Verum gel: after 16 and 22 days compared to 18 and 28 days with placebo gel). Eschars of the liquid treated burns fell off earlier than of the gel treated burns. Pain scores were not applicable because they were low and differences between the lesions could not be discriminated on the back. Combudoron seems to have positive effects on healing of grade 2 laser induced burns which deserve further investigation. Copyright © 2011 Elsevier Ltd. All rights reserved.

CE: Original Research: The Lived Experience of Social Media by Young Adult Burn Survivors.

PubMed

Giordano, Marie S

2016-08-01

: Young adult burn survivors who were burned before they reached young adulthood (before the age of 18) face particular challenges in meeting their needs for socialization. Social media are widely used by adolescents and young adults, and permit socialization without face-to-face communication. This qualitative, phenomenological study was conducted in order to explore and describe the lived experience of social media by young adult burn survivors. Five women and four men between the ages of 20 and 25 years were interviewed; before the age of 18 years, each had sustained burns over more than 25% of their total body surface area. Van Manen's phenomenological methodology provided the study framework. Five essential themes emerged: identity, connectivity, social support, making meaning, and privacy. The participants used social media as a way to express their identity while safeguarding their privacy, and as a way to make meaning out of their traumatic experiences. Connecting with others facilitated a flow of social support and information, which was motivating and encouraging. The findings indicate that the use of social media by young adult burn survivors may be warranted as a way to further their healing processes. The knowledge gained from this study may also be useful in facilitating the development of nursing interventions aimed at preparing young adult burn survivors for reentry into society.

Near-death experiences, posttraumatic growth, and life satisfaction among burn survivors.

PubMed

Royse, David; Badger, Karen

2017-03-01

Survivors of large burns may face positive and negative psychological after-effects from close-to-death injuries. This study is the first to examine their near-death experiences (NDEs) and posttraumatic growth (PTG) and life satisfaction afterwards. With an available sample of 92 burn survivors, half met the criteria for an NDE using an objective scale. Those who indicated religion was a source of strength and comfort had high scores on life satisfaction, PTG, and the NDE Scale. Individuals with larger burns reported greater PTG than those with smaller total body surface area burned (TBSA). There were no significant differences on life satisfaction, PTG, or NDEs when examined by gender or years since the burn injury. Elements of the NDE most frequently reported were: An altered sense of time, a sense of being out of the physical body, a feeling of peace, vivid sensations, and sense of being in an "other worldly" environment. Social workers and other health providers need to be comfortable helping burn survivors discuss any NDEs and process these through survivors' spirituality and religious belief systems as they recover.

Measuring ignitability for in situ burning of oil spills weathered under Arctic conditions: from laboratory studies to large-scale field experiments.

PubMed

Fritt-Rasmussen, Janne; Brandvik, Per Johan

2011-08-01

This paper compares the ignitability of Troll B crude oil weathered under simulated Arctic conditions (0%, 50% and 90% ice cover). The experiments were performed in different scales at SINTEF's laboratories in Trondheim, field research station on Svalbard and in broken ice (70-90% ice cover) in the Barents Sea. Samples from the weathering experiments were tested for ignitability using the same laboratory burning cell. The measured ignitability from the experiments in these different scales showed a good agreement for samples with similar weathering. The ice conditions clearly affected the weathering process, and 70% ice or more reduces the weathering and allows a longer time window for in situ burning. The results from the Barents Sea revealed that weathering and ignitability can vary within an oil slick. This field use of the burning cell demonstrated that it can be used as an operational tool to monitor the ignitability of oil spills. Copyright © 2011 Elsevier Ltd. All rights reserved.

Nitramine smokeless propellant research

NASA Technical Reports Server (NTRS)

Cohen, N. S.; Strand, L. P.

1977-01-01

A transient ballistics and combustion model is derived to represent the closed vessel experiment that is widely used to characterize propellants. A computer program is developed to solve the time-dependent equations, and is applied to explain aspects of closed vessel behavior. In the case of nitramine propellants the cratering of the burning surface associated with combustion above break-point pressures augments the effective burning rate as deduced from the closed vessel experiment. Low pressure combustion is significantly affected by the ignition process and, in the case of nitramine propellants, by the developing and changing surface structure. Thus, burning rates deduced from the closed vessel experiment may or may not agree with those measured in the equilibrium strand burner. Series of T burner experiments are performed to compare the combustion instability characteristics of nitramine (HMX) containing propellants and ammonium perchlorate (AP)propellants. Although ash produced by more fuel rich propellants could have provided mechanical suppression, results from clean-burning propellants permit the conclusion that HMX reduces the acoustic driving.

Psychosocial functioning differences in pediatric burn survivors compared with healthy norms.

PubMed

Maskell, Jessica; Newcombe, Peter; Martin, Graham; Kimble, Roy

2013-01-01

Burn injury is one of the most traumatic injuries a child or adolescent can experience. When a burn injury occurs, the child can suffer pain, uncertainty, fear, and trauma from acute treatment to rehabilitation and reintegration. He or she can also experience long-term psychosocial and psychological difficulties. The objective of the study was to compare health-related quality of life (HRQoL), psychopathology, and self-concept of children who have suffered a burn injury with a matched sample of healthy controls. Sixty-six children and adolescents with a burn injury, who were aged between 8 to 17 years, and a caregiver were recruited from six burn centers in Australia and New Zealand. Participants completed the Paediatric Quality of Life Inventory, the Strengths and Difficulties Questionnaire, and the Piers-Harris Self-Concept Scale (P-H SCS). Scores were compared with published normative data. As scarring and appearance are a distinct issue, the Paediatric Quality of Life Inventory cancer module perceived physical appearance subscale was also included. Pediatric burn survivors and their caregivers reported significantly higher emotional and behavioral problems and lower HRQoL, but no significant differences in self-concept compared with healthy counterparts. Pediatric burn survivors also reported significantly poorer perceived physical appearance than the matched pediatric cancer sample. Burned children reported lowered quality of life, particularly related to scarring and appearance; however, they reported normative self-concept. This may be because of self-concept being a psychological trait, whereas HRQoL is influenced by societal norms and expectations. Psychosocial support is necessary to build positive coping strategies and manage the unpleasant social experiences that may reduce quality of life.

Shock timing experiments on the National Ignition Facility: Initial results and comparison with simulation

NASA Astrophysics Data System (ADS)

Robey, H. F.; Boehly, T. R.; Celliers, P. M.; Eggert, J. H.; Hicks, D.; Smith, R. F.; Collins, R.; Bowers, M. W.; Krauter, K. G.; Datte, P. S.; Munro, D. H.; Milovich, J. L.; Jones, O. S.; Michel, P. A.; Thomas, C. A.; Olson, R. E.; Pollaine, S.; Town, R. P. J.; Haan, S.; Callahan, D.; Clark, D.; Edwards, J.; Kline, J. L.; Dixit, S.; Schneider, M. B.; Dewald, E. L.; Widmann, K.; Moody, J. D.; Döppner, T.; Radousky, H. B.; Throop, A.; Kalantar, D.; DiNicola, P.; Nikroo, A.; Kroll, J. J.; Hamza, A. V.; Horner, J. B.; Bhandarkar, S. D.; Dzenitis, E.; Alger, E.; Giraldez, E.; Castro, C.; Moreno, K.; Haynam, C.; LaFortune, K. N.; Widmayer, C.; Shaw, M.; Jancaitis, K.; Parham, T.; Holunga, D. M.; Walters, C. F.; Haid, B.; Mapoles, E. R.; Sater, J.; Gibson, C. R.; Malsbury, T.; Fair, J.; Trummer, D.; Coffee, K. R.; Burr, B.; Berzins, L. V.; Choate, C.; Brereton, S. J.; Azevedo, S.; Chandrasekaran, H.; Eder, D. C.; Masters, N. D.; Fisher, A. C.; Sterne, P. A.; Young, B. K.; Landen, O. L.; Van Wonterghem, B. M.; MacGowan, B. J.; Atherton, J.; Lindl, J. D.; Meyerhofer, D. D.; Moses, E.

2012-04-01

Capsule implosions on the National Ignition Facility (NIF) [Lindl et al., Phys. Plasmas 11, 339 (2004)] are underway with the goal of compressing deuterium-tritium (DT) fuel to a sufficiently high areal density (ρR) to sustain a self-propagating burn wave required for fusion power gain greater than unity. These implosions are driven with a carefully tailored sequence of four shock waves that must be timed to very high precision in order to keep the DT fuel on a low adiabat. Initial experiments to measure the strength and relative timing of these shocks have been conducted on NIF in a specially designed surrogate target platform known as the keyhole target. This target geometry and the associated diagnostics are described in detail. The initial data are presented and compared with numerical simulations. As the primary goal of these experiments is to assess and minimize the adiabat in related DT implosions, a methodology is described for quantifying the adiabat from the shock velocity measurements. Results are contrasted between early experiments that exhibited very poor shock timing and subsequent experiments where a modified target geometry demonstrated significant improvement.

LETTER: ECH pre-ionization and assisted startup in the fully superconducting KSTAR tokamak using second harmonic

NASA Astrophysics Data System (ADS)

Bae, Y. S.; Jeong, J. H.; Park, S. I.; Joung, M.; Kim, J. H.; Hahn, S. H.; Yoon, S. W.; Yang, H. L.; Kim, W. C.; Oh, Y. K.; England, A. C.; Namkung, W.; Cho, M. H.; Jackson, G. L.; Bak, J. S.; KSTAR Team

2009-02-01

This letter reports on the successful demonstration of the second harmonic electron cyclotron heating (ECH)-assisted startup in the first plasma experiments recently completed in the fully superconducting Korea Superconducting Tokamak Advanced Research (KSTAR) device whose major and minor radii are 1.8 m and 0.5 m, respectively. For the second harmonic ECH-assisted startup, an 84 GHz EC wave at 0.35 MW was launched before the onset of the toroidal electric field of the Ohmic system. And it was observed that this was sufficient to achieve breakdown in the ECH pre-ionization phase, allow burn-through and sustain the plasma during the current ramp with a low loop voltage of 2.0 V and a corresponding toroidal electric field of 0.24 V m-1at the innermost vacuum vessel wall (R = 1.3 m). This is a lower value than 0.3 Vm-1 which is the maximum electric field in ITER. Due to the limited volt-seconds and the loop voltage of the Ohmic power system, the extended pulse duration of the ECH power up to 180 ms allowed the plasma current to rise up to more than 100 kA with a ramp-up rate of 0.8 MA s-1.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbajal, L.; Warwick Univ., Coventry; Dendy, R. O.

Ion cyclotron emission (ICE) offers unique promise as a diagnostic of the fusion born alpha-particle population in magnetically confined plasmas. Pioneering observations from JET and TFTR found that ICE intensity P ICE scales approximately linearly with the measured neutron flux from fusion reactions, and with the inferred concentration, n /n i , of fusion-born alpha-particles confined within the plasma. We present fully nonlinear self-consistent kinetic simulations that reproduce this scaling for the first time. This resolves a longstanding question in the physics of fusion alpha particle confinement and stability in MCF plasmas. It confirms the MCI as the likely emissionmore » mechanism and greatly strengthens the basis for diagnostic exploitation of ICE in future burning plasmas.« less

Measuring Fluxes Of Heat To A Plasma-Arc Anode

NASA Technical Reports Server (NTRS)

Sankovic, John M.; Menart, James A.; Pfender, Emil; Heberlein, Joachim

1995-01-01

Three probes constructed to provide measurements indicative of conductive, convective, and radiative transfer of heat from free-burning plasma arc to water-cooled copper anode used in generating arc. Each probe consists mainly of copper body with two thermocouples embedded at locations 4 mm apart along length. Thermocouples provide measure of rate of conduction of heat along probe and transfers of heat from plasma to sensing surface at tip of probe. Probes identical except sensing surface of one uncoated and other two coated with different materials to make them sensitive to different components of overall flux of heat.

Physical Simulation of a Prolonged Plasma-Plume Exposure of a Space Debris Object

NASA Astrophysics Data System (ADS)

Shuvalov, V. A.; Gorev, N. B.; Tokmak, N. A.; Kochubei, G. S.

2018-05-01

A methodology has been developed for the physical (laboratory) simulation of the prolonged exposure of a space debris object to high-energy ions of a plasma plume for removing the object into low-Earth orbit with its subsequent burning in the Earth's atmosphere. The methodology is based on the equivalence criteria of two modes of exposure (in the Earth's ionosphere and in the setup) and the procedure for accelerated resource tests in terms of the sputtering of the space debris material and its deceleration by a plasma jet in the Earth's ionosphere.

Sawtooth pacing by real-time auxiliary power control in a tokamak plasma.

PubMed

Goodman, T P; Felici, F; Sauter, O; Graves, J P

2011-06-17

In the standard scenario of tokamak plasma operation, sawtooth crashes are the main perturbations that can trigger performance-degrading, and potentially disruption-generating, neoclassical tearing modes. This Letter demonstrates sawtooth pacing by real-time control of the auxiliary power. It is shown that the sawtooth crash takes place in a reproducible manner shortly after the removal of that power, and this can be used to precisely prescribe, i.e., pace, the individual sawteeth. In combination with preemptive stabilization of the neoclassical tearing modes, sawtooth pacing provides a new sawtooth control paradigm for improved performance in burning plasmas.

The experience of scar management for adults with burns: An interpretative phenomenological analysis.

PubMed

Martin, C; Bonas, S; Shepherd, L; Hedges, E

2016-09-01

Burns can have both physical and psychological effects on individuals. Pressure garments and silicone gels are used to improve the aesthetic appearance and functions of the skin, but these treatments have been associated with various physical, emotional, sexual and social difficulties. Interpretative phenomenological analysis (IPA) was used to explore participants' experiences of scar management. IPA examines individual experiences before comparing results across cases, and is suited to capture the different ways in which individuals experience a phenomena as well as cautiously looking at patterns across cases. Eight burn patients who had experienced scar management, including pressure garments, were interviewed. Two superordinate themes were identified: Assimilation of Pressure Garment Identity, and Psychosocial Functions of the Pressure Garments. The findings offered insight into the positive and negative experiences of scar management, describing the diverse personal and social functions of the pressure garments and how they became integrated into participants' identities. By understanding the individual nature of these experiences, healthcare professionals can enhance support around these issues and potentially aid adherence to treatment. Further research with different demographic groups as well as for other burn treatments would be useful to develop and contextualise these findings. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finley, V.L.; Wiezcorek, M.A.

This report gives the results of the environmental activities and monitoring programs at the Princeton Plasma Physics Laboratory (PPPL) for CY93. The report is prepared to provide the U.S. Department of Energy (DOE) and the public with information on the level of radioactive and non-radioactive pollutants, if any, added to the environment as a result of PPPL operations, as well as environmental initiatives, assessments, and programs that were undertaken in 1993. The objective of the Annual Site Environmental Report is to document evidence that DOE facility environmental protection programs adequately protect the environment and the public health. The Princeton Plasmamore » Physics Laboratory has engaged in fusion energy research since 1951. The long-range goal of the U.S. Magnetic Fusion Energy Research Program is to develop and demonstrate the practical application of fusion power as an alternate energy source. In 1993, PPPL had both of its two large tokamak devices in operation; the Tokamak Fusion Test Reactor (TFTR) and the Princeton Beta Experiment-Modification (PBX-M). PBX-M completed its modifications and upgrades and resumed operation in November 1991. TFTR began the deuterium-tritium (D-T) experiments in December 1993 and set new records by producing over six million watts of energy. The engineering design phase of the Tokamak Physics Experiment (TPX), which replaced the cancelled Burning Plasma Experiment in 1992 as PPPL`s next machine, began in 1993 with the planned start up set for the year 2001. In 1993, the Environmental Assessment (EA) for the TFRR Shutdown and Removal (S&R) and TPX was prepared for submittal to the regulatory agencies.« less

Burn Survivors' Perceptions regarding Relevant Sexual Education Strategies

ERIC Educational Resources Information Center

Parrott, Yolan; Esmail, Shaniff

2010-01-01

Purpose: This paper aims to investigate the unique issues childhood burn survivors experience in relation to sex education and sexual development. Design/methodology/approach: Using a phenomenological approach, participants described their lived experiences with regards to sex education and the sexuality issues they encountered as child burn…

Space Shuttle Exhaust Modifications of the Mid-Latitude Ionospheric Plasma As Diagnosed By Ground Based Radar

NASA Astrophysics Data System (ADS)

Lind, F. D.; Erickson, P. J.; Bhatt, A.; Bernhardt, P. A.

2009-12-01

The Space Shuttle's Orbital Maneuvering System (OMS) engines have been used since the early days of the STS program for active ionospheric modification experiments designed to be viewed by ground based ionospheric radar systems. In 1995, the Naval Research Laboratory initiated the Shuttle Ionospheric Modification with Pulsed Localized Exhaust (SIMPLEX) Program using dedicated Space Shuttle OMS burns scheduled through the US Department of Defense's Space Test Program. SIMPLEX objectives include generation of localized ion-acoustic turbulence and the formation of ionospheric density irregularities for injections perpendicular to the local magnetic field, creating structures which can scatter incident UHF radar signals. We discuss radar observations made during several recent SIMPLEX mid-latitude experiments conducted over the Millstone Hill incoherent scatter radar system in Westford, Massachusetts. OMS engine firings release 10 kg/s of CO2, H2, H2O, and N2 molecules which charge exchange with ambient O+ ions in the F region, producing molecular ions and long lived electron density depletions as recombination occurs with ambient electrons. Depending on the magnetic field angle, the high velocity of the injected reactive exhaust molecules relative to the background ionosphere can create longitudinal propagating ion acoustic waves with amplitudes well above normal thermal levels and stimulate a wide variety of plasma instability processes. These effects produce high radar cross section targets readily visible to the Millstone Hill system, a high power large aperture radar designed to measure very weak scatter from the quiescent background ionosphere. We will survey the plasma instability parameter space explored to date and discuss plans for future SIMPLEX observations.

Use of albumin as a risk factor for hospital mortality among burn patients in Brazil: non-concurrent cohort study.

PubMed

Caleman, Gilson; Morais, José Fausto de; Puga, Maria Eduarda Dos Santos; Riera, Rachel; Atallah, Alvaro Nagib

2010-01-01

among burn patients, it is common to use colloidal substances under the justification that it is necessary to correct the oncotic pressure of the plasma, thereby reducing the edema in the burnt area and the hypotension. The aim here was to assess the risk of hospital mortality, comparing the use of albumin and crystalloid solutions for these patients. non-concurrent historical cohort study at Faculdade de Medicina de Marília; within the Postgraduate program on Internal and Therapeutic Medicine, Universidade Federal de São Paulo; and at the Brazilian Cochrane Center. burn patients hospitalized between 2000 and 2001, with registration in the Hospital Information System, who received albumin, were compared with those who received other types of volume replacement. The primary outcome was the hospital mortality rate. The data were collected from files within the Datasus software. 39,684 patients were included: 24,116 patients with moderate burns and 15,566 patients with major burns. Among the men treated with albumin, the odds ratio for the risk of death was 20.58 (95% confidence interval, CI: 11.28-37.54) for moderate burns and 6.24 (CI 5.22-7.45) for major burns. Among the women, this risk was 40.97 for moderate burns (CI 21.71-77.30) and 7.35 for major burns (CI 5.99-9.01). The strength of the association between the use of albumin and the risk of death was maintained for the other characteristics studied, with statistical significance. the use of albumin among patients with moderate and major burns was associated with considerably increased mortality.

Prevalence Study of the Risk of Burns in the Public Schools Population in Charleston, South Carolina (Under the Direction of Stanley Schuman).

ERIC Educational Resources Information Center

Littlefield, Charlyne Butler

This Charleston Burn Study was designed to determine the prevalence of the burn risks in the public school population in Charleston, South Carolina. Twelve schools representing a cross section of urban, suburban, rural and military populations participated in the project. Students completed forms that revealed their experience with burns and…

STUDENT AWARD FINALIST: Oxygen Pathways in Streamer Discharge for Transient Plasma Ignition

NASA Astrophysics Data System (ADS)

Pendleton, S. J.; Bowman, S.; Singleton, D.; Watrous, J.; Carter, C.; Lempert, W.; Gundersen, M. A.

2011-10-01

The use of streamers for the ignition of fuels, also known as transient plasma ignition (TPI), has been shown in a variety of engines to improve combustion through decreased ignition delay, increased lean burn capability and increased energy release relative to conventional spark ignition. The mechanisms behind these improvements, however, remain poorly understood. Temperature measurements by optical emission spectroscopy demonstrate that ignition by TPI is a nonthermal process, and thus is almost entirely dependent on the production and presence of electron impact-created active species in the discharge afterglow. Of particular interest are active oxygen species due to their relatively long lifetimes at high pressures and the pivotal role they play in combustion reactions. In order to elucidate the oxygen pathways, here we report the investigation of the temporal evolution of the populations of atomic oxygen and ozone by use of two-photon absorption laser induced fluorescence (TALIF) and UV absorption, respectively. Experimental results are presented and compared to kinetic modeling of the streamers. Future experiments are proposed to better understand the physics behind TPI. Supported by NSF, AFOSR, NumerEx-ONR, AFRL-WPAFB.

GYROKINETIC PARTICLE SIMULATION OF TURBULENT TRANSPORT IN BURNING PLASMAS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horton, Claude Wendell

2014-06-10

The SciDAC project at the IFS advanced the state of high performance computing for turbulent structures and turbulent transport. The team project with Prof Zhihong Lin [PI] at Univ California Irvine produced new understanding of the turbulent electron transport. The simulations were performed at the Texas Advanced Computer Center TACC and the NERSC facility by Wendell Horton, Lee Leonard and the IFS Graduate Students working in that group. The research included a Validation of the electron turbulent transport code using the data from a steady state university experiment at the University of Columbia in which detailed probe measurements of themore » turbulence in steady state were used for wide range of temperature gradients to compare with the simulation data. These results were published in a joint paper with Texas graduate student Dr. Xiangrong Fu using the work in his PhD dissertation. X.R. Fu, W. Horton, Y. Xiao, Z. Lin, A.K. Sen and V. Sokolov, “Validation of electron Temperature gradient turbulence in the Columbia Linear Machine, Phys. Plasmas 19, 032303 (2012).« less

The Ignition Requirements of the Degeneracy Microspheres of Deuterium Helium-3 Mixture with Low-Radioactive

NASA Astrophysics Data System (ADS)

Mahdavi, M.; Khodadadi Azadboni, F.

2012-08-01

This paper examines the burn characteristics for inertial confinement D/3 He fuel pellets with different concentrations of Helium-3. It is shown that the Helium-3 relative density of the fuel mixture plays a significant role in determining the burn characteristics and fuel gain. In spite of the safety of the plasma degeneracy of D/3 He fuel with fraction of y = 0.2 (y: Helium-3 content parameter), ignition of fuel is impossible. In design fuel extra to safety should be considered fractional burn-up and fuel gain. The main contribution of this research is to show that the plasma degeneracy of equimolar mixture of D/3 He fuel lowers the ignition temperature and increases fuel gain. The results indicate that a ≤ 0.3 is difficult to ignite reasonable driver energy. A fuel gain of 378 can be obtained with a D/3 He fuel with fraction of y = 0.33, and areal density (ρ R) of 12 g/cm2. It is found that the fuel gain of an equimolar D/3 He fuel at temperature of 70 keV and ρ R value of 8.5 g/cm2 is 480. This value gain is higher by about 22% than the case of the pellets (y = 0.33).

Engineering of the `PCAST machine`

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinnis, J.; Brooks, A.; Brown, T.

The President`s Committee of Advisors on Science and Technology (PCAST) has suggested that a device with a mission of ignition and moderate burn time could address the physics of burning plasmas at a lesser cost than ITER with its more comprehensive physics and technology mission. The Department of Energy commissioned a study to explore this PCAST suggestion. This paper describes the results of the engineering portion of the study of this `PCAST Machine;` physics is covered in a companion paper authored by G.H. Neilson, et al; and the costs are covered in a companion paper by R.T. Simmons, et al.more » Both are published in the proceedings of this conference. The study was undertaken by a team under the direction of Bruce Montgomery that included representatives from MIT, PPPL, ORNL, LLNL, GA, Northrup-Grumman, and Stone and Webster. The performance requirements for the PCAST machine are to form and sustain a burning plasma for three helium accumulation times. The philosophy adopted for this design was to achieve the required performance at lower cost by decreasing the major radius to five meters, increasing the toroidal field to 7 tesla, and using stronger shaping. The major device parameters are given. 4 refs., 4 figs., 1 tab.« less

Modeling crop residue burning experiments to evaluate smoke emissions and plume transport

EPA Science Inventory

Crop residue burning is a common land management practice that results in emissions of a variety of pollutants with negative health impacts. Modeling systems are used to estimate air quality impacts of crop residue burning to support retrospective regulatory assessments and also ...

Control of neutral particle fueling and exhaust by plasma edge topology optimization in Wendelstein 7-X and HSX

NASA Astrophysics Data System (ADS)

Stephey, Laurie

2016-10-01

Comparative experiments at the HSX and Wendelstein 7-X stellarators are being performed. At W7-X it was shown that fine control of the edge magnetic structure in W7-X is a feasible actuator to control global particle confinement. During the startup campaign of W7-X, the edge magnetic structure is defined by five poloidal limiters. Inside of the last closed flux surface in the standard magnetic configuration, the 5/6 resonance and corresponding magnetic island are located directly inside of the plasma source region. Inward movement of the island in a predominantly electron-root transport regime has been found to increase the effective helium confinement time τp* He, a critical metric for plasma purity control in future burning plasmas, by a factor of two. The experimental analysis is supported by fully 3-D fluid plasma and kinetic neutral modeling using the EMC3-EIRENE code and will be compared to these experimental results from both devices. A single reservoir, single species particle balance will be extracted from experimental measurements aided by the fully 3-D modeling analysis from EMC3-EIRENE to quantify the causal link established above based on measured parameters. At HSX, similar investigations to those performed at W7-X are ongoing. HSX has substantial flexibility in both its edge magnetic configuration and also in edge connection lengths via limiter insertion. Both are being examined to study any resulting changes global particle confinement and provide insight into the physics of the underlying mechanism. Together with the results from W7-X, both experiments will provide information on the link between the plasma edge topology and the global particle confinement. This work was supported in part by the U.S. Department of Energy under Grants DE-SC0014210, DE-FG02-93ER54222, DE-AC05-00OR22725, DOE LANS Contract DE-AC52- 06NA25396, and within the EUROfusion Consortium under Euratom Grant No 633053.

A lateral tarsorrhaphy with forehead hitch to pre-empt and treat burns ectropion with a contextual review of burns ectropion management

PubMed Central

Lymperopoulos, Nikolaos S; Jordan, Daniel J; Jeevan, Ranjeet; Shokrollahi, Kayvan

2016-01-01

Introduction: Facial burns around the eyes and eyelid ectropion can lead to corneal exposure, irritation, dryness, epiphora, infection or visual loss. We undertook a review of the published articles describing management of eyelid burns as well as methods to treat or prevent ectropion. We describe early experience of a surgical technique that we have found to mitigate ectropion in facial burns with peri-ocular involvement. Materials and methods: Two illustrative cases with our surgical technique is described from our experience of three cases. We reviewed the literature using the PubMed and EMBASE databases using the search terms ‘burn’ and ‘ectropion’. Results: The literature review produced a total of 17 relevant papers. Treatment options for eyelid burns were varied and were invariably level 4 or 5 evidence. Various techniques were used to treat eyelid burns including the use of a full thickness skin graft with or without concurrent scar contracture release but also use of a local flap reconstruction with or without a tissue expander or release of the underlying muscle. Other techniques included canthoplasty, Z-plasty, forehead flaps, fat transfer, and tarsorrhaphy with full thickness skin grafting. In general, the focus of articles was therapeutic and reconstructive rather than pre-emptive/preventative management. Procedure: We describe our early experience of a novel technique for temporary lateral tarsorrhaphy with forehead hitch which protexts the globe and counters the scar- and gravity-related ectropic effects on the lower eyelids. Discussion: Facial burns pose a difficult problem to the burn surgeon, especially when the eyelids are affected, both directly or indirectly. The optimal surgical management of eyelid burns remains unclear and the literature base lies mainly in the domain of case series. We review the literature on this subject and tabulate our findings and also describe our contribution to this area with a method of lateral and lower lid elevator that we have found valuable. PMID:29799558

CONFERENCE DESCRIPTION Theory of Fusion Plasmas: Varenna-Lausanne International Workshop

NASA Astrophysics Data System (ADS)

Garbet, X.; Sauter, O.

2010-12-01

The Joint Varenna-Lausanne international workshop on Theory of Fusion Plasmas takes place every other year in a place particularly favourable for informal and in-depth discussions. Invited and contributed papers present state-of-the-art research in theoretical plasma physics, covering all domains relevant to fusion plasmas. This workshop always welcomes a fruitful mix of experienced researchers and students, to allow a better understanding of the key theoretical physics models and applications. Theoretical issues related to burning plasmas Anomalous Transport (Turbulence, Coherent Structures, Microinstabilities) RF Heating and Current Drive Macroinstabilities Plasma-Edge Physics and Divertors Fast particles instabilities Further details: http://Varenna-Lausanne.epfl.ch The conference is organized by: Centre de Recherches en Physique des Plasmas, Ecole Polytechnique Fédérale de Lausanne, Association EURATOM - Confédération Suisse 'Piero Caldirola' International Centre for the Promotion of Science and International School of Plasma Physics Istituto di Fisica del Plasma del CNR, Milano Editors: X Garbet (CEA, Cadarache, France) and O Sauter (CRPP-EPFL, Lausanne, Switzerland)

Quantifying Fusion Born Ion Populations in Magnetically Confined Plasmas using Ion Cyclotron Emission

DOE PAGES

Carbajal, L.; Warwick Univ., Coventry; Dendy, R. O.; ...

2017-03-07

Ion cyclotron emission (ICE) offers unique promise as a diagnostic of the fusion born alpha-particle population in magnetically confined plasmas. Pioneering observations from JET and TFTR found that ICE intensity P ICE scales approximately linearly with the measured neutron flux from fusion reactions, and with the inferred concentration, n /n i , of fusion-born alpha-particles confined within the plasma. We present fully nonlinear self-consistent kinetic simulations that reproduce this scaling for the first time. This resolves a longstanding question in the physics of fusion alpha particle confinement and stability in MCF plasmas. It confirms the MCI as the likely emissionmore » mechanism and greatly strengthens the basis for diagnostic exploitation of ICE in future burning plasmas.« less

Quantifying Fusion Born Ion Populations in Magnetically Confined Plasmas using Ion Cyclotron Emission

NASA Astrophysics Data System (ADS)

Carbajal, L.; Dendy, R. O.; Chapman, S. C.; Cook, J. W. S.

2017-03-01

Ion cyclotron emission (ICE) offers a unique promise as a diagnostic of the fusion born alpha-particle population in magnetically confined plasmas. Pioneering observations from JET and TFTR found that ICE intensity PICE scales approximately linearly with the measured neutron flux from fusion reactions, and with the inferred concentration, nα/ni, of fusion born alpha particles confined within the plasma. We present fully nonlinear self-consistent kinetic simulations that reproduce this scaling for the first time. This resolves a long-standing question in the physics of fusion alpha-particle confinement and stability in magnetic confinement fusion plasmas. It confirms the magnetoacoustic cyclotron instability as the likely emission mechanism and greatly strengthens the basis for diagnostic exploitation of ICE in future burning plasmas.

Thermomagnetic burn control for magnetic fusion reactor

DOEpatents

Rawls, John M.; Peuron, Unto A.

1982-01-01

Apparatus is provided for controlling the plasma energy production rate of a magnetic-confinement fusion reactor, by controlling the magnetic field ripple. The apparatus includes a group of shield sectors (30a, 30b, etc.) formed of ferromagnetic material which has a temperature-dependent saturation magnetization, with each shield lying between the plasma (12) and a toroidal field coil (18). A mechanism (60) for controlling the temperature of the magnetic shields, as by controlling the flow of cooling water therethrough, thereby controls the saturation magnetization of the shields and therefore the amount of ripple in the magnetic field that confines the plasma, to thereby control the amount of heat loss from the plasma. This heat loss in turn determines the plasma state and thus the rate of energy production.

Quantifying Fusion Born Ion Populations in Magnetically Confined Plasmas using Ion Cyclotron Emission.

PubMed

Carbajal, L; Dendy, R O; Chapman, S C; Cook, J W S

2017-03-10

Ion cyclotron emission (ICE) offers a unique promise as a diagnostic of the fusion born alpha-particle population in magnetically confined plasmas. Pioneering observations from JET and TFTR found that ICE intensity P_{ICE} scales approximately linearly with the measured neutron flux from fusion reactions, and with the inferred concentration, n_{α}/n_{i}, of fusion born alpha particles confined within the plasma. We present fully nonlinear self-consistent kinetic simulations that reproduce this scaling for the first time. This resolves a long-standing question in the physics of fusion alpha-particle confinement and stability in magnetic confinement fusion plasmas. It confirms the magnetoacoustic cyclotron instability as the likely emission mechanism and greatly strengthens the basis for diagnostic exploitation of ICE in future burning plasmas.

Two Contemporary Problems in Magnetized Plasmas: The ion-ion hybrid resonator and MHD stability in a snowflake divertor

NASA Astrophysics Data System (ADS)

Farmer, William Anthony

The first part of the dissertation investigates the effects of multiple-ions on the propagation of shear Alfven waves. It is shown that the presence of a second ion-species allows for the formation of an ion-ion hybrid resonator in the presence of a magnetic well. A full-wave description is shown to explain the measured eigenfrequencies and spatial form of the resonator modes identified in experiments in the Large Plasma Device (LAPD) at UCLA. However, it is determined that neither electron collisions or radial convection of the mode due to coupling to either the compressional or ion-Bernstein wave can explain the observed dissipation. Ray tracing studies for shear Alfven waves are performed in various magnetic geometries of contemporary interest. In a tokamak, it is found that the hybrid resonator can exist in the cold-plasma regime, but that ion-temperature effects combined with curvature effects cause the wave reflection point to shift towards the cyclotron frequency of the heavier ion. A one-dimensional WKB model is applied to a tokamak geometry for conditions corresponding to a burning fusion plasma to characterize the resonator. Instability due to fusion-born alpha particles is assessed. An approximate form of the global eigenmode is considered. It is identified that magnetic field shear combined with large ion temperature can cause coupling to an ion-Bernstein wave, which can limit the instability. Finally, the radiation pattern of shear Alfven waves generated by a burst of charged particles in the presence of two-ion species is considered. The spectral content and spatial patterns of the radiated waves are determined. The second part of the dissertation considers the MHD stability of the plasma near a divertor in a tokamak. Two types of modes are considered: a ballooning mode and an axisymmetric, quasi-flute mode. Instability thresholds are derived for both modes and numerically evaluated for parameters relevant to recent experiments. This is done to determine whether these modes could be responsible for convection of the plasma in the vicinity of the poloidal null point. It is determined that MHD instability about a standard equilibrium is unlikely to explain the experimental results observed on the tokamak, TCV [Reimerdes et al., Plasma Phys. Contr. Fusion 55, 124027 (2013)]. From these results, it is concluded that the most likely explanation for the discrepancy is that the underlying equilibrium assumed in the calculation does not contain all the complexities present in the experiments.

Chemical and physical transformations of organic aerosol from the photo-oxidation of open biomass burning emissions in an environmental chamber

Treesearch

C. J. Hennigan; M. A. Miracolo; G. J. Engelhart; A. A. May; A. A. Presto; T. Lee; A. P. Sullivan; G. R. McMeeking; H. Coe; C. E. Wold; W.-M. Hao; J. B. Gilman; W. C. Kuster; J. de Gouw; B. A. Schichtel; J. L. Collett; S. M. Kreidenweis; A. L. Robinson

2011-01-01

Smog chamber experiments were conducted to investigate the chemical and physical transformations of organic aerosol (OA) during photo-oxidation of open biomass burning emissions. The experiments were carried out at the US Forest Service Fire Science Laboratory as part of the third Fire Lab at Missoula Experiment (FLAME III). We investigated emissions from 12 different...

Wiseman during BASS experiment

NASA Image and Video Library

2014-07-02

ISS040-E-031397 (2 July 2014) --- NASA astronaut Reid Wiseman, Expedition 40 flight engineer, works with a combustion experiment known as the Burning and Suppression of Solids (BASS) in the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft.

Paediatric injuries associated with the use of disposable barbecues: are we finding ourselves in hot sand?

PubMed

Vermaak, Pieter; Haj Basheer, Mahammed; Taki, Hussein; Burge, Timothy

2012-08-01

To document, describe and raise awareness of a preventable injury associated with the use of disposable barbecues. We conducted a retrospective study of incidents involving barbecue burns. Cases were identified through the burn injury database of a tertiary paediatric burns referral centre and case notes reviewed. Experiments were performed to evaluate the dissipation of heat from sand. Over a 3-month period, 9 children were identified out of a series of 296. The median age was 5 years and burns were sustained through contact with hot sand where disposable barbecues had been used. 87% (n=13) of the burns were partial thickness and most affected critical areas such as the hands and feet. The majority (93%) responded well to debridement and simple dressings and all patients made a complete recovery. Experiments show that, even after a prolonged period of time, sand can retain sufficient heat to cause a contact burn. We have noted an increased incidence of burns with this mechanism of injury. The burns are usually superficial, they tend to occur predominantly in children and involve critical areas. We suggest that areas where disposable barbecues have stood should be cooled and children kept away from the area for at least 5min. The results of the study have been forwarded to the Prevention Committee of the British Burn Association with the aim of raising awareness of this mechanism of burn. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

Results of Propellant Mixing Variable Study Using Precise Pressure-Based Burn Rate Calculations

NASA Technical Reports Server (NTRS)

Stefanski, Philip L.

2014-01-01

A designed experiment was conducted in which three mix processing variables (pre-curative addition mix temperature, pre-curative addition mixing time, and mixer speed) were varied to estimate their effects on within-mix propellant burn rate variability. The chosen discriminator for the experiment was the 2-inch diameter by 4-inch long (2x4) Center-Perforated (CP) ballistic evaluation motor. Motor nozzle throat diameters were sized to produce a common targeted chamber pressure. Initial data analysis did not show a statistically significant effect. Because propellant burn rate must be directly related to chamber pressure, a method was developed that showed statistically significant effects on chamber pressure (either maximum or average) by adjustments to the process settings. Burn rates were calculated from chamber pressures and these were then normalized to a common pressure for comparative purposes. The pressure-based method of burn rate determination showed significant reduction in error when compared to results obtained from the Brooks' modification of the propellant web-bisector burn rate determination method. Analysis of effects using burn rates calculated by the pressure-based method showed a significant correlation of within-mix burn rate dispersion to mixing duration and the quadratic of mixing duration. The findings were confirmed in a series of mixes that examined the effects of mixing time on burn rate variation, which yielded the same results.

Low Stretch PMMA Burning in Microgravity: Status of the Ground-Based Program and New ISS Glovebox Experiment SALSA

NASA Technical Reports Server (NTRS)

Olson, S. L.; T'ien, J. S.; Armstrong, J. B.

2001-01-01

The objective of this ground-based program is to study low stretch diffusion flames burning PMMA as the solid fuel to determine the relationship between buoyant low stretch burning in normal gravity and forced flow low stretch burning in microgravity. The low stretch is generated in normal gravity by using the buoyant convection induced by burning the bottom of a large radius of curvature sample. Low stretch is also generated using the Combustion Tunnel drop tower rig (2.2 and 5.2 second facilities), which provides a forced convective low velocity flow past smaller radius of curvature samples. Lastly, an ISS glovebox investigation is being developed to study low stretch burning of PMMA spheres to obtain long duration testing needed to accurately assess the flammability and burning characteristics of the material in microgravity. A comparison of microgravity experiment results with normal gravity test results allows us to establish a direct link between a material's burning characteristics in normal gravity (easily measured) with its burning characteristics in extraterrestrial environments, including microgravity forced convective environments. Theoretical predictions and recent experimental results indicate that it should be possible to understand a material's burning characteristics in the low stretch environment of spacecraft (non-buoyant air movement induced by fans and crew disturbances) by understanding its burning characteristics in an equivalent Earth-based low stretch environment (induced by normal gravity buoyancy). Similarly, Earth-based stretch environments can be made equivalent to those in Lunar- and Martian-surface stretch environments (which would induce partial-gravity buoyancy).

An insight into burns in a developing country: a Sri Lankan experience.

PubMed

Lau, Y S

2006-10-01

Burn injuries represent a diverse and varied challenge to medical and paramedical staff. The management of burns and their sequelae in a well-equipped, modern burns unit remains demanding despite advances in surgical techniques and development of tissue-engineered biomaterials; in a developing country, these difficulties are amplified many times. Sri Lanka has a high incidence of burn-related injuries annually due to a combination of adverse social, economic and cultural factors. The management of burn injuries remains a formidable public health problem. The epidemiology of burns, challenges faced in their management and effective strategies specific to Sri Lanka, such as the Safe Bottle Lamp campaign, are highlighted in this paper.

Merging-compression formation of high temperature tokamak plasma

NASA Astrophysics Data System (ADS)

Gryaznevich, M. P.; Sykes, A.

2017-07-01

Merging-compression is a solenoid-free plasma formation method used in spherical tokamaks (STs). Two plasma rings are formed and merged via magnetic reconnection into one plasma ring that then is radially compressed to form the ST configuration. Plasma currents of several hundred kA and plasma temperatures in the keV-range have been produced using this method, however until recently there was no full understanding of the merging-compression formation physics. In this paper we explain in detail, for the first time, all stages of the merging-compression plasma formation. This method will be used to create ST plasmas in the compact (R ~ 0.4-0.6 m) high field, high current (3 T/2 MA) ST40 tokamak. Moderate extrapolation from the available experimental data suggests the possibility of achieving plasma current ~2 MA, and 10 keV range temperatures at densities ~1-5  ×  1020 m-3, bringing ST40 plasmas into a burning plasma (alpha particle heating) relevant conditions directly from the plasma formation. Issues connected with this approach for ST40 and future ST reactors are discussed

Implementation of a plasma-neutral model in NIMROD

NASA Astrophysics Data System (ADS)

Taheri, S.; Shumlak, U.; King, J. R.

2016-10-01

Interaction between plasma fluid and neutral species is of great importance in the edge region of magnetically confined fusion plasmas. The presence of neutrals can have beneficial effects such as fueling burning plasmas and quenching the disruptions in tokamaks, as well as deleterious effects like depositing high energy particles on the vessel wall. The behavior of edge plasmas in magnetically confined systems has been investigated using computational approaches that utilize the fluid description for the plasma and Monte Carlo transport for neutrals. In this research a reacting plasma-neutral model is implemented in NIMROD to study the interaction between plasma and neutral fluids. This model, developed by E. T. Meier and U. Shumlak, combines a single-fluid magnetohydrodynamic (MHD) plasma model with a gas dynamic neutral fluid model which accounts for electron-impact ionization, radiative recombination, and resonant charge exchange. Incorporating this model into NIMROD allows the study of the interaction between neutrals and plasma in a variety of plasma science problems. An accelerated plasma moving through a neutral gas background in a coaxial electrode configuration is modeled, and the results are compared with previous calculations from the HiFi code.

Social challenges of visible scarring after severe burn: A qualitative analysis.

PubMed

Martin, Lisa; Byrnes, Michelle; McGarry, Sarah; Rea, Suzanne; Wood, Fiona

2017-02-01

Visible scarring after burn causes social challenges which impact on interpersonal connection. These have health impacts which may worsen outcomes for burn patients and reduce the potential for posttraumatic growth (PTG). The aim of the study was to investigate adult burn survivors' experiences of interpersonal relationships as potential barriers to posttraumatic recovery following hand or face burns. This qualitative study explored patient experiences of interpersonal situations. A purposive sample (n=16) who had visible burn scarring were interviewed more than two years after their burn. Emotional barriers included the fear of rejection, feelings of self-consciousness, embarrassment and humiliation. Situational barriers included inquisitive questions, comments and behaviours of others. Responses depended on the relationship with the person, how they were asked and the social situation. Active coping strategies included positive reframing, humour, changing the self, and pre-empting questions. Avoidant coping strategies included avoidance of eye contact, closed body language, hiding scars, and learning to shut down conversations. Emotional and situational barriers reduced social connection and avoidant coping strategies reduced the interaction of people with burns with others. Active coping strategies need to be taught to assist with social reintegration. This highlights the need for peer support, family support and education, and social skills training. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Burns from illegal drug manufacture: case series and management.

PubMed

Porter, C J W; Armstrong, J R

2004-01-01

This case series presents our experience with burns sustained while manufacturing illegal drugs. All adult burn admissions in an 18-month period were retrospectively reviewed. All patients suspected of sustaining burns from illegal drug manufacture were contacted. Information regarding the burn mechanism was sought. Nine of the 64 adult burn admissions were caused by explosions during the manufacture of cannabis oil. Young males with hand and face burns were heavily represented. First-aid treatment was often ignored in favor of hiding incriminating evidence. Only two patients gave honest admission histories. Illegal drug manufacture is becoming more common as synthetic drugs become more consumer desirable. Burns sustained may be thermal and/or chemical. Dishonest patient histories negatively influence burn management. A high level of suspicion is required for diagnosing and treating burns from illegal drug manufacture. Public education is unlikely to be effective as the financial rewards outweigh the perceived risks.

Predicted effects of prescribed burning and harvesting on forest recovery and sustainability in southwest Georgia, USA.

PubMed

Garten, Charles T

2006-12-01

A model-based analysis of the effect of prescribed burning and forest thinning or clear-cutting on stand recovery and sustainability was conducted at Fort Benning, GA, in the southeastern USA. Two experiments were performed with the model. In the first experiment, forest recovery from degraded soils was predicted for 100 years with or without prescribed burning. In the second experiment simulations began with 100 years of predicted stand growth, then forest sustainability was predicted for an additional 100 years under different combinations of prescribed burning and forest harvesting. Three levels of fire intensity (low, medium, and high), that corresponded to 17%, 33%, and 50% consumption of the forest floor C stock by fire, were evaluated at 1-, 2-, and 3-year fire return intervals. Relative to the control (no fire), prescribed burning with a 2- or 3-year return interval caused only a small reduction in predicted steady state soil C stocks (< or =25%) and had no effect on steady state tree wood biomass, regardless of fire intensity. Annual high intensity burns did adversely impact forest recovery and sustainability (after harvesting) on less sandy soils, but not on more sandy soils that had greater N availability. Higher intensity and frequency of ground fires increased the chance that tree biomass would not return to pre-harvest levels. Soil N limitation was indicated as the cause of unsustainable forests when prescribed burns were too frequent or too intense to permit stand recovery.

Observation of Critical-Gradient Behavior in Alfvén-Eigenmode-Induced Fast-Ion Transport.

PubMed

Collins, C S; Heidbrink, W W; Austin, M E; Kramer, G J; Pace, D C; Petty, C C; Stagner, L; Van Zeeland, M A; White, R B; Zhu, Y B

2016-03-04

Experiments in the DIII-D tokamak show that fast-ion transport suddenly becomes stiff above a critical threshold in the presence of many overlapping small-amplitude Alfvén eigenmodes (AEs). The threshold is phase-space dependent and occurs when particle orbits become stochastic due to resonances with AEs. Above threshold, equilibrium fast-ion density profiles are unchanged despite increased drive, and intermittent fast-ion losses are observed. Fast-ion Dα spectroscopy indicates radially localized transport of the copassing population at radii that correspond to the location of midcore AEs. The observation of stiff fast-ion transport suggests that reduced models can be used to effectively predict alpha profiles, beam ion profiles, and losses to aid in the design of optimized scenarios for future burning plasma devices.

Gain stabilization control system of the upgraded magnetic proton recoil neutron spectrometer at JET.

PubMed

Sjöstrand, Henrik; Andersson Sundén, E; Conroy, S; Ericsson, G; Gatu Johnson, M; Giacomelli, L; Gorini, G; Hellesen, C; Hjalmarsson, A; Popovichev, S; Ronchi, E; Tardocchi, M; Weiszflog, M

2009-06-01

Burning plasma experiments such as ITER and DEMO require diagnostics capable of withstanding the harsh environment generated by the intense neutron flux and to maintain stable operating conditions for times longer than present day systems. For these reasons, advanced control and monitoring (CM) systems will be necessary for the reliable operation of diagnostics. This paper describes the CM system of the upgraded magnetic proton recoil neutron spectrometer installed at the Joint European Torus focusing in particular on a technique for the stabilization of the gain of the photomultipliers coupled to the neutron detectors. The results presented here show that this technique provides good results over long time scales. The technique is of general interest for all diagnostics that employ scintillators coupled to photomultiplier tubes.

Early-Time Symmetry Tuning in the Presence of Cross-Beam Energy Transfer in ICF Experiments on the National Ignition Facility

DOE PAGES

Dewald, E. L.; Milovich, J. L.; Michel, P.; ...

2013-12-01

At the National Ignition Facility (NIF) we have successfully tuned the early time (~2 ns) lowest order Legendre mode (P 2) of the incoming radiation drive asymmetry of indirectly driven ignition capsule implosions by varying the inner power cone fraction. The measured P 2/P 0 sensitivity vs come fraction is similar to calculations, but a significant -15 to -20% P 2/P 0 offset was observed. This can be explained by a considerable early time laser energy transfer from the outer to the inner beams during the laser burn-through of the Laser Entrance Hole (LEH) windows and hohlraum fill gas whenmore » the LEH plasma is still dense and relatively cold.« less

Radiation hardening of gated x-ray imagers for the National Ignition Facility (invited).

PubMed

Bell, P M; Bradley, D K; Kilkenny, J D; Conder, A; Cerjan, C; Hagmann, C; Hey, D; Izumi, N; Moody, J; Teruya, A; Celeste, J; Kimbrough, J; Khater, H; Eckart, M J; Ayers, J

2010-10-01

The National Ignition Facility will soon be producing x-ray flux and neutron yields higher than any produced in laser driven implosion experiments in the past. Even a non-igniting capsule will require x-ray imaging of near burning plasmas at 10(17) neutrons, requiring x-ray recording systems to work in more hostile conditions than we have encountered in past laser facilities. We will present modeling, experimental data and design concepts for x-ray imaging with electronic recording systems for this environment (ARIANE). A novel instrument, active readout in a nuclear environment, is described which uses the time-of-flight difference between the gated x-ray signal and the neutron which induces a background signal to increase the yield at which gated cameras can be used.

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

PubMed

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-08-15

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher concentrations in the residue solid ash of PVC as compared to those from the other types of plastic. The open-air burning of plastic material and their toxic emissions is of growing concern in areas of municipal solid waste where open-fires occur intentionally or accidentally. Another problem is building fires in which victims may suffer severe smoke inhalation from burning plastic materials in homes and in working places.

The effects of crude oil and remediation burning on three clones of smooth cordgrass (Spartina alterniflora Loisel.)

USGS Publications Warehouse

Smith, D.L.; Proffitt, C.E.

1999-01-01

Burning has been employed as an oil spill remediation technique in coastal marshes, even though the combined and interactive effects of soil and burning on vegetation are poorly understood. Variation among clones of perennial marsh grasses in response to these perturbations is not known. We performed a greenhouse experiment designed to assess the effects of Venezuelan crude oil alone and of oil followed by burning on three clonal genets of Spartina alterniflora. The fully-crossed 6-mo experiment involved five dosages of oil (0 l m-2, 4 l m-2, 8 l m-2, 16 l m-2, and 24 l m-2) and two burn treatments (burned or unburned) applied to ramets from three clones. All oil-only dosages reduced survival, but burning after oiling (oil + burn treatments) increased survival relative to oil-only groups in all except the highest two oil dosages. Higher oil-only treatments also reduced ramet densities and inhibited density increases over 6 mo. Burning after treatment with the 16 l m-2 oil concentration allowed increased production of new ramets, but burning exacerbated the negative impacts on ramet density at the oil concentration of 24 l m-2. At some intermediate oil dosages, burning remediated the negative effects of oil on aboveground biomass production and growth in height. There was a significant effect of oil-only treatments on numbers of flowering ramets produced, in which two clones responded with decreased flower production and one exhibited increased flowering. There was no main effect of oil + burn on flowering. There were significant among-clones differences in all response variables to one or both treatments. Our experiment demonstrates that burning of oiled S. alterniflora marshes may have little measurable effect at low levels of Venezuelan crude oil, can remediate the effects of oil at intermediate oil concentrations, but can increase the negative impacts at high concentrations of oil. These results indicate that oil spills have the potential to adversely affect genetic diversity in S. alterniflora populations by eliminating some sensitive clonal variants or changing the relative dominance of genets. These results suggest certain clones may be better suited for phytoremediation or restoration planting following oil spills.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sevik, James; Wallner, Thomas; Pamminger, Michael

The efficiency improvement and emissions reduction potential of lean and exhaust gas recirculation (EGR)-dilute operation of spark-ignition gasoline engines is well understood and documented. However, dilute operation is generally limited by deteriorating combustion stability with increasing inert gas levels. The combustion stability decreases due to reduced mixture flame speeds resulting in significantly increased combustion initiation periods and burn durations. A study was designed and executed to evaluate the potential to extend lean and EGR-dilute limits using a low-energy transient plasma ignition system. The low-energy transient plasma was generated by nanosecond pulses and its performance compared to a conventional transistorized coilmore » ignition (TCI) system operated on an automotive, gasoline direct-injection (GDI) single-cylinder research engine. The experimental assessment was focused on steady-state experiments at the part load condition of 1500 rpm 5.6 bar indicated mean effective pressure (IMEP), where dilution tolerance is particularly critical to improving efficiency and emission performance. Experimental results suggest that the energy delivery process of the low-energy transient plasma ignition system significantly improves part load dilution tolerance by reducing the early flame development period. Statistical analysis of relevant combustion metrics was performed in order to further investigate the effects of the advanced ignition system on combustion stability. Results confirm that at select operating conditions EGR tolerance and lean limit could be improved by as much as 20% (from 22.7 to 27.1% EGR) and nearly 10% (from λ = 1.55 to 1.7) with the low-energy transient plasma ignition system.« less

BASS-II Hardware Repair

NASA Image and Video Library

2014-03-27

ISS039-E-005726 (27 March 2014) --- Expedition 39 Flight Engineer Rick Mastracchio performs inflight maintenance on an experiment called Burning and Suppression of Solids (BASS)-II. The investigation examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The BASS-II experiment will guide strategies for materials flammability screening for use in spacecraft as well as provide valuable data on solid fuel burning behavior in microgravity. BASS-II results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS-II Experiment

NASA Image and Video Library

2014-08-02

Image taken on card 8 during BASS-II flame test session with reduced O2 partial pressure. Session conducted on GMT 213. The Burning and Suppression of Solids - II (BASS-II) investigation examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The BASS-II experiment will guide strategies for materials flammability screening for use in spacecraft as well as provide valuable data on solid fuel burning behavior in microgravity. BASS-II results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

Preface to Special Topic: Advances in Radio Frequency Physics in Fusion Plasmas

NASA Astrophysics Data System (ADS)

Tuccillo, Angelo A.; Phillips, Cynthia K.; Ceccuzzi, Silvio

2014-06-01

It has long been recognized that auxiliary plasma heating will be required to achieve the high temperature, high density conditions within a magnetically confined plasma in which a fusion "burn" may be sustained by copious fusion reactions. Consequently, the application of radio and microwave frequency electromagnetic waves to magnetically confined plasma, commonly referred to as RF, has been a major part of the program almost since its inception in the 1950s. These RF waves provide heating, current drive, plasma profile control, and Magnetohydrodynamics (MHD) stabilization. Fusion experiments employ electromagnetic radiation in a wide range of frequencies, from tens of MHz to hundreds of GHz. The fusion devices containing the plasma are typically tori, axisymmetric or non, in which the equilibrium magnetic fields are composed of a strong toroidal magnetic field generated by external coils, and a poloidal field created, at least in the symmetric configurations, by currents flowing in the plasma. The waves are excited in the peripheral regions of the plasma, by specially designed launching structures, and subsequently propagate into the core regions, where resonant wave-plasma interactions produce localized heating or other modification of the local equilibrium profiles. Experimental studies coupled with the development of theoretical models and advanced simulation codes over the past 40+ years have led to an unprecedented understanding of the physics of RF heating and current drive in the core of magnetic fusion devices. Nevertheless, there are serious gaps in our knowledge base that continue to have a negative impact on the success of ongoing experiments and that must be resolved as the program progresses to the next generation devices and ultimately to "demo" and "fusion power plant." A serious gap, at least in the ion cyclotron (IC) range of frequencies and partially in the lower hybrid frequency ranges, is the difficulty in coupling large amount of power to the plasma while minimizing the interaction between the plasma and launching structures. These potentially harmful interactions between the plasma and the vessel and launching structures are challenging: (i) significant and variable loss of power in the edge regions of confined plasmas and surrounding vessel structures adversely affect the core plasma performance and lifetime of a device; (ii) the launcher design is partly "trial and error," with the consequence that launchers may have to be reconfigured after initial tests in a given device, at an additional cost. Over the broader frequency range, another serious gap is a quantitative lack of understanding of the combined effects of nonlinear wave-plasma processes, energetic particle interactions and non-axisymmetric equilibrium effects on determining the overall efficiency of plasma equilibrium and stability profile control techniques using RF waves. This is complicated by a corresponding lack of predictive understanding of the time evolution of transport and stability processes in fusion plasmas.

A Preliminary Assessment of the SURF Reactive Burn Model Implementation in FLAG

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Carl Edward; McCombe, Ryan Patrick; Carver, Kyle

Properly validated and calibrated reactive burn models (RBM) can be useful engineering tools for assessing high explosive performance and safety. Experiments with high explosives are expensive. Inexpensive RBM calculations are increasingly relied on for predictive analysis for performance and safety. This report discusses the validation of Menikoff and Shaw’s SURF reactive burn model, which has recently been implemented in the FLAG code. The LANL Gapstick experiment is discussed as is its’ utility in reactive burn model validation. Data obtained from pRad for the LT-63 series is also presented along with FLAG simulations using SURF for both PBX 9501 and PBXmore » 9502. Calibration parameters for both explosives are presented.« less

[The post-burn process--a determinant in local surgical treatment of deep burns].

PubMed

Bäumer, F; Henrich, H A

1988-12-01

Afterburning has been studied in the animal experiment by use of intravital dye indicators and by measuring partial oxygen pressure. After third degree burn the oxygen conduction of the damaged skin increased. The afterburning was seen to be finished on the 5th day after the burn trauma. The histological changes in the depth of the afterburn area reaches to the subcutis. The extend of the afterburn area was not related to the applied temperature or the duration of the experimental burn injury.

Development of a long-term ovine model of cutaneous burn and smoke inhalation injury and the effects of early excision and skin autografting

PubMed Central

Yamamoto, Yusuke; Enkhbaatar, Perenlei; Sakurai, Hiroyuki; Rehberg, Sebastian; Asmussen, Sven; Ito, Hiroshi; Sousse, Linda E.; Cox, Robert A.; Deyo, Donald J.; Traber, Lillian D.; Traber, Maret G.; Herndon, David N.; Traber, Daniel L.

2013-01-01

Smoke inhalation injury frequently increases the risk of pneumonia and mortality in burn patients. The pathophysiology of acute lung injury secondary to burn and smoke inhalation is well studied, but long-term pulmonary function, especially the process of lung tissue healing following burn and smoke inhalation, has not been fully investigated. By contrast, early burn excision has become the standard of care in the management of major burn injury. While many clinical studies and small-animal experiments support the concept of early burn wound excision, and show improved survival and infectious outcomes, we have developed a new chronic ovine model of burn and smoke inhalation injury with early excision and skin grafting that can be used to investigate lung pathophysiology over a period of 3 weeks. Materials and methods Eighteen female sheep were surgically prepared for this study under isoflurane anesthesia. The animals were divided into three groups: an Early Excision group (20% TBSA, third-degree cutaneous burn and 36 breaths of cotton smoke followed by early excision and skin autografting at 24 h after injury, n = 6), a Control group (20% TBSA, third-degree cutaneous burn and 36 breaths of cotton smoke without early excision, n = 6) and a Sham group (no injury, no early excision, n = 6). After induced injury, all sheep were placed on a ventilator and fluid-resuscitated with Lactated Ringers solution (4 mL/% TBS/kg). At 24 h post-injury, early excision was carried out to fascia, and skin grafting with meshed autografts (20/1000 in., 1:4 ratio) was performed under isoflurane anesthesia. At 48 h post-injury, weaning from ventilator was begun if PaO2/FiO2 was above 250 and sheep were monitored for 3 weeks. Results At 96 h post-injury, all animals were weaned from ventilator. There are no significant differences in PaO2/FiO2 between Early Excision and Control groups at any points. All animals were survived for 3 weeks without infectious complication in Early Excision and Sham groups, whereas two out of six animals in the Control group had abscess in lung. The percentage of the wound healed surviving area (mean ± SD) was 74.7 ± 7.8% on 17 days post-surgery in the Early Excision group. Lung wet-to-dry weight ratio (mean ± SD) was significantly increased in the Early Excision group vs. Sham group (p < 0.05). The calculated net fluid balance significantly increased in the early excision compared to those seen in the Sham and Control groups. Plasma protein, oncotic pressure, hematocrit of % baseline, hemoglobin of % baseline, white blood cell and neutrophil were significantly decreased in the Early Excision group vs. Control group. Conclusions The early excision model closely resembles practice in a clinical setting and allows long-term observations of pulmonary function following burn and smoke inhalation injury. Further studies are warranted to assess lung tissue scarring and measuring collagen deposition, lung compliance and diffusion capacity. PMID:22459154

Metabolic measures of male southern toads (Bufo terrestris) exposed to coal combustion waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ward, C.K.; Appel, A.G.; Mendonca, M.T.

2006-03-15

Southern toads (Bufo terrestris) are found in coal fly ash collection basins associated with coal-burning electrical power plants. These basins contain large amounts of trace metals and organisms found in these basins are known to accumulate large quantities of metals. Studies on a variety of organisms exposed to trace metals found that they experience a significant increase in standard metabolic rate. We experimentally exposed southern toads to metal-contaminated sediment and food and measured changes in standard and exercise metabolic rates as well as changes in body, liver and muscle mass, blood glucose, and corticosterone. We found that toads exposed tomore » trace metal contamination gained significantly less mass (18.3%) than control toads (31.3%) when food was limited and experienced significantly decreased RQ after exercise. However, contaminated toads did not experience changes in standard or exercise metabolic rates, plasma glucose levels, and hepatic or muscle percentage indices whether food was limited or not.« less

Fuel gain exceeding unity in an inertially confined fusion implosion.

PubMed

Hurricane, O A; Callahan, D A; Casey, D T; Celliers, P M; Cerjan, C; Dewald, E L; Dittrich, T R; Döppner, T; Hinkel, D E; Berzak Hopkins, L F; Kline, J L; Le Pape, S; Ma, T; MacPhee, A G; Milovich, J L; Pak, A; Park, H-S; Patel, P K; Remington, B A; Salmonson, J D; Springer, P T; Tommasini, R

2014-02-20

Ignition is needed to make fusion energy a viable alternative energy source, but has yet to be achieved. A key step on the way to ignition is to have the energy generated through fusion reactions in an inertially confined fusion plasma exceed the amount of energy deposited into the deuterium-tritium fusion fuel and hotspot during the implosion process, resulting in a fuel gain greater than unity. Here we report the achievement of fusion fuel gains exceeding unity on the US National Ignition Facility using a 'high-foot' implosion method, which is a manipulation of the laser pulse shape in a way that reduces instability in the implosion. These experiments show an order-of-magnitude improvement in yield performance over past deuterium-tritium implosion experiments. We also see a significant contribution to the yield from α-particle self-heating and evidence for the 'bootstrapping' required to accelerate the deuterium-tritium fusion burn to eventually 'run away' and ignite.

Optical closure experiments for biomass smoke aerosols

Treesearch

L. A. Mack; E. J. T. Levin; S. M. Kreidenweis; D. Obrist; H. Moosmuller; K. A. Lewis; W. P. Arnott; G. R. McMeeking; A. P. Sullivan; C. E. Wold; W.-M. Hao; J. L. Collett; W. C. Malm

2010-01-01

A series of laboratory experiments at the Fire Laboratory at Missoula (FLAME) investigated chemical, physical, and optical properties of fresh smoke samples from combustion of wildland fuels that are burned annually in the western and southeastern US The burns were conducted in the combustion chamber of the US Forest Service Fire Sciences Laboratory in Missoula,...

Porcine Burn Shock - Development of a Reliable Model and Response to Sodium, Water, and Plasma Loads Administered for Resuscitation

DTIC Science & Technology

1973-06-01

nm.ddt. inital, Diet n*Mf) Thomas L. Wachtel, M.D. G. R. McCahan, Jr., D.V.M. 0 REPORT CATS 70. TOTAL No. Or PAGE Nb O. or mrs June 1973 - w 78 0. CON...observations of caloric uptake of pigskin, rise in temperature at the dermis-fat interface as a function of both time and skin surface temperature and an...of Iso-, Hypo - and Hypertonic Sodium Solutions in the Treatment of Burn Shock in Mice," Surgery, 57: 698-704, May 1965. 24. Rosenthal, S. M

User's guide for FRMOD, a zero dimensional FRM burn code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driemeryer, D.; Miley, G.H.

1979-10-15

The zero-dimensional FRM plasma burn code, FRMOD is written in the FORTRAN language and is currently available on the Control Data Corporation (CDC) 7600 computer at the Magnetic Fusion Energy Computer Center (MFECC), sponsored by the US Department of Energy, in Livermore, CA. This guide assumes that the user is familiar with the system architecture and some of the utility programs available on the MFE-7600 machine, since online documentation is available for system routines through the use of the DOCUMENT utility. Users may therefore refer to it for answers to system related questions.

Gerst during BASS-II experiment

NASA Image and Video Library

2014-07-30

ISS040-E-083576 (30 July 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, performs two tests with a combustion experiment known as the Burning and Suppression of Solids (BASS-II) in the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft.

Gerst during BASS-II experiment

NASA Image and Video Library

2014-07-30

ISS040-E-083578 (30 July 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, performs two tests with a combustion experiment known as the Burning and Suppression of Solids (BASS-II) in the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft.

Predictive Value of IL-8 for Sepsis and Severe Infections after Burn Injury - A Clinical Study

PubMed Central

Kraft, Robert; Herndon, David N; Finnerty, Celeste C; Cox, Robert A; Song, Juquan; Jeschke, Marc G

2014-01-01

The inflammatory response induced by burn injury contributes to increased incidence of infections, sepsis, organ failure, and mortality. Thus, monitoring post-burn inflammation is of paramount importance but so far there are no reliable biomarkers available to monitor and/or predict infectious complications after burn. As IL-8 is a major mediator for inflammatory responses, the aim of our study was to determine whether IL-8 expression can be used to predict post-burn sepsis, infections, and mortality other outcomes post-burn. Plasma cytokines, acute phase proteins, constitutive proteins, and hormones were analyzed during the first 60 days post injury from 468 pediatric burn patients. Demographics and clinical outcome variables (length of stay, infection, sepsis, multiorgan failure (MOF), and mortality were recorded. A cut-off level for IL-8 was determined using receiver operating characteristic (ROC) analysis. Statistical significance is set at (p<0.05). ROC analysis identified a cut-off level of 234 pg/ml for IL-8 for survival. Patients were grouped according to their average IL-8 levels relative to this cut off and stratified into high (H) (n=133) and low (L) (n=335) groups. In the L group, regression analysis revealed a significant predictive value of IL-8 to percent of total body surface area (TBSA) burned and incidence of MOF (p<0.001). In the H group IL-8 levels were able to predict sepsis (p<0.002). In the H group, elevated IL-8 was associated with increased inflammatory and acute phase responses compared to the L group (p<0.05). High levels of IL-8 correlated with increased MOF, sepsis, and mortality. These data suggest that serum levels of IL-8 may be a valid biomarker for monitoring sepsis, infections, and mortality in burn patients. PMID:25514427

Plasma reforming and partial oxidation of hydrocarbon fuel vapor to produce synthesis gas and/or hydrogen gas

DOEpatents

Kong, Peter C.; Detering, Brent A.

2003-08-19

Methods and systems for treating vapors from fuels such as gasoline or diesel fuel in an internal combustion engine, to form hydrogen gas or synthesis gas, which can then be burned in the engine to produce more power. Fuel vapor, or a mixture of fuel vapor and exhaust gas and/or air, is contacted with a plasma, to promote reforming reactions between the fuel vapor and exhaust gas to produce carbon monoxide and hydrogen gas, partial oxidation reactions between the fuel vapor and air to produce carbon monoxide and hydrogen gas, or direct hydrogen and carbon particle production from the fuel vapor. The plasma can be a thermal plasma or a non-thermal plasma. The plasma can be produced in a plasma generating device which can be preheated by contact with at least a portion of the hot exhaust gas stream, thereby decreasing the power requirements of the plasma generating device.

Plasma Reforming And Partial Oxidation Of Hydrocarbon Fuel Vapor To Produce Synthesis Gas And/Or Hydrogen Gas

DOEpatents

Kong, Peter C.; Detering, Brent A.

2004-10-19

Methods and systems are disclosed for treating vapors from fuels such as gasoline or diesel fuel in an internal combustion engine, to form hydrogen gas or synthesis gas, which can then be burned in the engine to produce more power. Fuel vapor, or a mixture of fuel vapor and exhaust gas and/or air, is contacted with a plasma, to promote reforming reactions between the fuel vapor and exhaust gas to produce carbon monoxide and hydrogen gas, partial oxidation reactions between the fuel vapor and air to produce carbon monoxide and hydrogen gas, or direct hydrogen and carbon particle production from the fuel vapor. The plasma can be a thermal plasma or a non-thermal plasma. The plasma can be produced in a plasma generating device which can be preheated by contact with at least a portion of the hot exhaust gas stream, thereby decreasing the power requirements of the plasma generating device.

Plasma facing materials and components for future fusion devices—development, characterization and performance under fusion specific loading conditions

NASA Astrophysics Data System (ADS)

Linke, J.

2006-04-01

The plasma exposed components in existing and future fusion devices are strongly affected by the plasma material interaction processes. These mechanisms have a strong influence on the plasma performance; in addition they have major impact on the lifetime of the plasma facing armour and the joining interface between the plasma facing material (PFM) and the heat sink. Besides physical and chemical sputtering processes, high heat quasi-stationary fluxes during normal and intense thermal transients are of serious concern for the engineers who develop reliable wall components. In addition, the material and component degradation due to intense fluxes of energetic neutrons is another critical issue in D-T-burning fusion devices which requires extensive R&D. This paper presents an overview on the materials development and joining, the testing of PFMs and components, and the analysis of the neutron irradiation induced degradation.

α Heating in a Stagnated Z-pinch

NASA Astrophysics Data System (ADS)

Appelbe, Brian; Chittenden, Jeremy

2009-01-01

A computational investigation of a scheme for magneto-inertial confinement fusion in a Z-pinch is carried out. In the scheme implosion of a deuterium-tritium fuel mass is preceded by formation of a hotspot containing warm, dense plasma on axis. The presence of the hotspot increases energy yield. Compression of the hotspot by the main fuel mass initiates thermonuclear burn. There is significant heating of the plasma by thermonuclear α particles which are confined by the strong magnetic field of the Z-pinch.

[Advances in the research of effects of glutamine on immune function of burn patients].

PubMed

Liu, Y H; Guo, P F; Chen, G Y; Bo, Y C; Ma, Y; Cui, Z J

2018-04-20

Glutamine is the most abundant amino acid found in plasma and cells. It is the preferred fuel for enterocytes in the small intestine, macrophages, and lymphocytes. After serious burn, increased requirement of glutamine by the gastrointestinal tract, kidney and lymphocytes, and relatively insufficient self synthesis likely contribute to the rapid decline of glutamine in circulation and cells. Glutamine supplementation can not only protect intestinal mucosa, maintain normal intestinal barrier function, reduce bacterial translocation, and enhance the intestinal immune function, but also increase the number of lymphocytes, enhance the phagocytic function of macrophage, promote the synthesis of immunoglobulin, and reduce the body's inflammatory response, so as to enhance the immune function. Therefore, glutamine supplementation can improve and enhance the immune function, reduce complications and promote the prognosis of severely burned patients.

Art Therapy on a Hospital Burn Unit: A Step towards Healing and Recovery.

ERIC Educational Resources Information Center

Russel, Johanna

1995-01-01

Describes how art therapy can benefit patients hospitalized due to severe burns, who suffer psychological as well as physical trauma. Outlines the psychological phases, identifies how burn patients typically experience their healing process, and discusses how art therapy can assist the patient at each stage of the recovery process. (JPS)

Experience of nursing staff facing the hospitalization of burned children.

PubMed

Inocencio Soares, Nataly Tsumura; Grubisich Mendes Tacla, Mauren Teresa

2014-01-01

To present the experiences of nursing staff working with hospitalized burned children. Qualitative study. Data were obtained from semi-structured interviews applied to 16 people of the nursing team (12 professional technicians and 4) working at a burn treatment center. For the analysis, the Method information Interpretation of the Senses was used. The theoretical basis used to support the discussion of the study was proposed by Geertz's interpretive anthropology. The narratives showed that the process of care to burned children is stressful for the participants because they are psychologically involved with the tragic story of a patient who suffered burns, and therefore with the clinical situation. This allows for the development of empathy. On the other hand there cultural involvement facing and accepting the consequences of what happened to the patient, due to the change of body image stigma that the child will suffer hamper the re-socialization of the child after discharge. The nursing team is affected in various ways during the care of hospitalized burned children. There is need for educational programs for their preparation in the care of these patients.

Effectiveness of a chemical herder in association with in-situ burning of oil spills in ice-infested water.

PubMed

van Gelderen, Laurens; Fritt-Rasmussen, Janne; Jomaas, Grunde

2017-02-15

The average herded slick thickness, surface distribution and burning efficiency of a light crude oil were studied in ice-infested water to determine the effectiveness of a chemical herder in facilitating the in-situ burning of oil. Experiments were performed in a small scale (1.0m 2 ) and an intermediate scale (19m 2 ) setup with open water and 3/10, 5/10 and 7/10 brash ice coverages. The herded slick thicknesses (3-8mm) were ignitable in each experiment. The presence of ice caused fracturing of the oil during the herding process, which reduced the size of the herded slicks and, as a consequence, their ignitability, which in turn decreased the burning efficiency. Burning efficiencies relative to the ignited fraction of the oil were in the expected range (42-86%). This shows that the herder will be an effective tool for in-situ burning of oil when the ignitability issues due to fracturing of the oil are resolved. Copyright © 2016 Elsevier Ltd. All rights reserved.

Response of LaBr3(Ce) scintillators to 2.5 MeV fusion neutrons.

PubMed

Cazzaniga, C; Nocente, M; Tardocchi, M; Croci, G; Giacomelli, L; Angelone, M; Pillon, M; Villari, S; Weller, A; Petrizzi, L; Gorini, G

2013-12-01

Measurements of the response of LaBr3(Ce) to 2.5 MeV neutrons have been carried out at the Frascati Neutron Generator and at tokamak facilities with deuterium plasmas. The observed spectrum has been interpreted by means of a Monte Carlo model. It is found that the main contributor to the measured response is neutron inelastic scattering on (79)Br, (81)Br, and (139)La. An extrapolation of the count rate response to 14 MeV neutrons from deuterium-tritium plasmas is also presented. The results are of relevance for the design of γ-ray diagnostics of fusion burning plasmas.

[Lay emphasis on the treatment of massive burn casualties in conflagration].

PubMed

Tang, Hong-tai; Ma, Bing; Xia, Zhao-fan

2012-06-01

Burn surgery belongs to disaster medicine. Burn is a common trauma that occurs in social activities of human beings in all ages, either in the time of peace or war. During the development of human medicine in modern times, the summary of experience in treating massive burn casualties due to severe fire accidents has effectively promoted the renovation of treating technology and theory of burns and the development of burn surgery. The results of treatment of burn injury in casualties occurred in the fire of Cocoanut Grove night club in Boston in 1942, and the high-rise apartment house fire in Shanghai in 2010 were summarized and analyzed in this article, emphasizing the correlating issues of inhalation injury.

Pediatric thermal injury: acute care and reconstruction update.

PubMed

Armour, Alexis D; Billmire, David A

2009-07-01

The acute and reconstructive care of each pediatric burn patient presents unique challenges to the plastic surgeon and the burn care team. : The purpose of this review article is to highlight the interdependence between the acute and reconstructive needs of pediatric burn patients as it pertains to each anatomical site. Relevant principles of acute pediatric burn care and burn reconstruction are outlined, based on the authors' experience and review of the literature. The need for late reconstruction in pediatric burn survivors is significantly influenced by the acute surgical and rehabilitative treatments. With their vulnerability to airway swelling, hypothermia, pulmonary edema, and ischemia-reperfusion injury, pediatric patients with large burns require precise, life-saving treatment in the acute phase. Decision-making in pediatric burn reconstruction must take into account the patient's future growth, maturity, and often lack of suitable donor sites. Appropriately selected reconstructive techniques are essential to optimize function, appearance, and quality of life in pediatric burn survivors.

Sharp and blunt force trauma concealment by thermal alteration in homicides: An in-vitro experiment for methodology and protocol development in forensic anthropological analysis of burnt bones.

PubMed

Macoveciuc, Ioana; Márquez-Grant, Nicholas; Horsfall, Ian; Zioupos, Peter

2017-06-01

Burning of human remains is one method used by perpetrators to conceal fatal trauma and expert opinions regarding the degree of skeletal evidence concealment are often disparate. This experiment aimed to reduce this incongruence in forensic anthropological interpretation of burned human remains and implicitly contribute to the development of research methodologies sufficiently robust to withstand forensic scrutiny in the courtroom. We have tested the influence of thermal alteration on pre-existing sharp and blunt trauma on twenty juvenile sheep radii in the laboratory using an automated impact testing system and an electric furnace. The testing conditions simulated a worst-case scenario where remains with pre-existing sharp or blunt trauma were exposed to burning with an intentional vehicular fire scenario in mind. All impact parameters as well as the burning conditions were based on those most commonly encountered in forensic cases and maintained constant throughout the experiment. The results have shown that signatures associated with sharp and blunt force trauma were not masked by heat exposure and highlights the potential for future standardization of fracture analysis in burned bone. Our results further emphasize the recommendation given by other experts on handling, processing and recording burned remains at the crime scene and mortuary. Copyright © 2017 Elsevier B.V. All rights reserved.

Impact of temperature-velocity distribution on fusion neutron peak shape

NASA Astrophysics Data System (ADS)

Munro, David

2016-10-01

Doppler broadening of the 14 MeV DT and 2.45 MeV DD fusion neutron lines has long been our best measure of temperature in a burning plasma. At the National Ignition Facility yields are high enough and our neutron spectrometers accurate enough that we see finer details of the peak shape. For example, we can measure the shift of the peak due to bulk motion of the plasma, and we see indications of non-thermal broadening, skew, and kurtosis of the peak caused by the variations of temperature and fluid velocity during burn. We can also distinguish spectral differences among several lines of sight. This talk will review the theory of fusion neutron line shape, show examples of non-Gaussian line shapes and directional variations in NIF data, and describe detailed spectral shapes we see in radhydro implosion simulations. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Impact of obesity on body image dissatisfaction and social integration difficulty in adolescent and young adult burn injury survivors

PubMed Central

Chondronikola, Maria; Sidossis, Labros S.; Richardson, Lisa M.; Temple, Jeff R.; van den Berg, Patricia A.; Herndon, David N.; Meyer, Walter J.

2012-01-01

Objective Burn injury deformities and obesity have been associated with social integration difficulty and body image dissatisfaction. However, the combined effects of obesity and burn injury in social integration difficulty and body image dissatisfaction are unknown. Methods Adolescent and young adults burn injury survivors were categorized as normal weight (n=47) or overweight and obese (n=21). Burn-related and anthropometric information was obtained from patients' medical records, while validated questionnaires were used to assess the main outcomes and possible confounders. Analysis of covariance and multiple linear regressions were performed to evaluate the objectives of this study. Results Obese and overweight burn injury survivors did not experience increased body image dissatisfaction (12 ± 4.3 vs 13.1 ± 4.4, p = 0.57) or social integration difficulty (17.5 ± 6.9 vs 15.5 ± 5.7, p=0.16) compared to normal weight burn injury survivors. Weight status was not a significant predictor of social integration difficulty or body image dissatisfaction (p=0.19 and p=0.24, respectively). However, mobility limitations predicted greater social integration difficulty (p=0.005) and body image dissatisfaction (p<0.001), while higher weight status at burn was a borderline significant predictor of body image dissatisfaction (p=0.05). Conclusions Obese and overweight adolescents and young adults, who sustained a major burn injury as children, do not experience greater social integration difficulty and body image dissatisfaction compared to normal weight burn injury survivors. Mobility limitations and higher weight status at burn are likely more important factors affecting the long-term social integration difficulty and body image dissatisfaction of these young people. PMID:23292577

Outcomes important to burns patients during scar management and how they compare to the concepts captured in burn-specific patient reported outcome measures.

PubMed

Jones, Laura L; Calvert, Melanie; Moiemen, Naiem; Deeks, Jonathan J; Bishop, Jonathan; Kinghorn, Philip; Mathers, Jonathan

2017-12-01

Pressure garment therapy (PGT) is an established treatment for the prevention and treatment of hypertrophic scarring; however, there is limited evidence for its effectiveness. Burn survivors often experience multiple issues many of which are not adequately captured in current PGT trial measures. To assess the effectiveness of PGT it is important to understand what outcomes matter to patients and to consider whether patient-reported outcome measures (PROMs) can be used to ascertain the effect of treatments on patients' health-related quality of life. This study aimed to (a) understand the priorities and perspectives of adult burns patients and the parents of burns patients who have experienced PGT via in-depth qualitative data, and (b) compare these with the concepts captured within burn-specific PROMs. We undertook 40 semi-structured interviews with adults and parents of paediatric and adolescent burns patients who had experienced PGT to explore their priorities and perspectives on scar management. Interviews were audio-recorded, transcribed and thematically analysed. The outcomes interpreted within the interview data were then mapped against the concepts captured within burn-specific PROMs currently in the literature. Eight core outcome domains were identified as important to adult patients and parents: (1) scar characteristics and appearance, (2) movement and function, (3) scar sensation, (4) psychological distress, adjustments and a sense of normality, (5) body image and confidence, (6) engagement in activities, (7) impact on relationships, and (8) treatment burden. The outcome domains presented reflect a complex holistic patient experience of scar management and treatments such as PGT. Some currently available PROMs do capture the concepts described here, although none assess psychological adjustments and attainment of a sense of normality following burn injury. The routine use of PROMs that represent patient experience and their relative contribution to trial outcome assessment versus clinical measures is now a matter for further research and debate. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Prehospital treatment of burns: a qualitative study of experiences, perceptions and reactions of victims.

PubMed

Sadeghi Bazargani, H; Fouladi, N; Alimohammadi, H; Sadeghieh Ahari, S; Agamohammadi, M; Mohamadi, R

2013-08-01

The manner in which burns are initially managed, at an incident scene, can affect the extent and depth of burn wounds and their final prognosis. The aim of this study was to understand people's experiences, perceptions and reactions towards the initial management of burns and fire accidents in Ardabil Province, Iran. In a qualitative study, 48 burn victims accompanied by their caregivers were enrolled. Focus group discussion (FGD) was used to collect data. All the interviews were recorded, transcribed and analysed using content analysis method. Four categories of information were retrieved in this study, including fire control, scald and burn wound management, seeking medical consultation and severity indicators. Uncertainty regarding what to do when someone catches fire was an evident finding that was explored through the discussions. The results revealed that transferring the patient to the hospital most often takes place after initial treatments administered at home. People believed that cooling a burn wound for a time longer than a few seconds may harm the wound. A strong belief in the efficacy of traditional remedies was disclosed when the statements of participants revealed that traditional or home-made remedies were widely used either to control pain immediately after burn and later during the wound repair process to accelerate the repair or to control the infection and prevent oedema and scar. Among these remedies, pennyroyal and grated potatoes seemed to be the most popular ones. Pennyroyal was thought to prevent infection and potatoes were used to relieve pain. People doubted the capability of health-care workers who work in rural health houses. People considered electrical burns and burns on the chest to be the most severe types of burns. Inappropriate perceptions regarding initial management of burns existed among the participants that should be addressed in future quantitative research or through developing programmes on secondary prevention of burns. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Injection therapy with triamcinolone hexacetonide in the treatment of burn scars in infancy: results of 44 cases.

PubMed

Grisolia, G A; Danti, D A; Santoro, S; Panozzo, G; Bonini, G; Pampaloni, A

1983-11-01

In many cases deep second degree and third degree burns cause severe scarring. The authors have reported here their experience of the treatment of hypertrophic scarring from burns carried out on 44 children with intralesional injections of a long-acting cortico-steroid (Triamcinolone hexacetonide) using the jet spray technique.

Experimental measurements and numerical modeling of marginal burning in live chaparral fuel beds

Treesearch

X. Zhou; D.R. Weise; S Mahalingam

2005-01-01

An extensive experimental and numerical study was completed to analyze the marginal burning behavior of live chaparral shrub fuels that grow in the mountains of southern California. Laboratory fire spread experiments were carried out to determine the effects of wind, slope, moisture content, and fuel characteristics on marginal burning in fuel beds of common...

Reduced quasilinear models for energetic particles interaction with Alfvenic eigenmodes

NASA Astrophysics Data System (ADS)

Ghantous, Katy

The Line Broadened Quasilinear (LBQ) and the 1.5D reduced models are able to predict the effect of Alfvenic eigenmodes' interaction with energetic particles in burning plasmas. This interaction can result in energetic-particle losses that can damage the first wall, deteriorate the plasma performance, and even prevent ignition. The 1.5D model assumes a broad spectrum of overlapping modes and, based on analytic expressions for the growth and damping rates, calculates the pressure profiles that the energetic particles relax to upon interacting with the modes. 1.5D is validated with DIII-D experiments and predicted neutron losses consistent with observation. The model is employed to predict alpha-particle fusion-product losses in a large-scale operational parameter-space for burning plasmas. The LBQ model captures the interaction both in the regime of isolated modes as well as in the conventional regime of overlapping modes. Rules were established that allow quasilinear equations to replicate the expected steady-state saturation levels of isolated modes. The fitting formula is improved and the model is benchmarked with a Vlasov code, BOT. The saturation levels are accurately predicted and the mode evolution is well-replicated in the case of steady-state evolution where the collisions are high enough that coherent structures do not form. When the collisionality is low, oscillatory behavior can occur. LBQ can also exhibit non-steady behavior, but the onset of oscillations occurs for much higher collisional rates in BOT than in LBQ. For certain parameters of low collisionality, hole-clump creation and frequency chirping can occur which are not captured by the LBQ model. Also, there are cases of non-steady evolution without chirping which is possible for LBQ to study. However the results are inconclusive since the periods and amplitudes of the oscillations in the mode evolution are not well-replicated. If multiple modes exist, they can grow to the point of overlap which results in two-dimensional diffusion with cross terms. A diffusion scheme is proposed and validated to resolve this dynamics in (Pφ,E) phase-space.

Quantitative studies of kinetic effects in direct- and indirect-drive Inertial Confinement Fusion implosions

NASA Astrophysics Data System (ADS)

Rinderknecht, Hans

2013-10-01

A comprehensive set of experiments using shock-driven implosions has been conducted to quantitatively study kinetic effects by exploring deviations from hydrodynamic behavior in plasmas relevant to inertial confinement fusion (ICF). Two types of targets were imploded at OMEGA to create ~10 keV, ~1022 cm-3 plasmas with conditions comparable to the incipient hotspot in ignition designs: thin-glass targets filled with mixtures of D2 and 3He gas; and thin deuterated-plastic shells filled with 3He. In the thin-glass experiments, the gas pressure was varied from 1 to 25 atm to scan the ion-mean-free path in the plasma at shock burn. The observed nuclear yields and temperatures deviated more strongly from hydrodynamic predictions as the ion-mean-free path increased to the order of the plasma size. This result provides the first direct experimental evidence how kinetic effects impact yields and ion temperature. The ratio of D to 3He was also varied while maintaining the fuel mass density. As the D fraction was reduced, the DD and D3He fusion products displayed an anomalous yield reduction. Separation of the D and 3He ion species across the strong (Mach ~10) shock-front will be discussed as the likely cause of this result. Finally, thin-CD shells filled with 3He produced significantly more D3He-protons when imploded than is explained by hydrodynamic mix models. This result suggests a kinetic form of mix dominates at the strongly-shocked shell-gas interface. This work was performed in collaboration with C. Li, M. Rosenberg, A. Zylstra, H. Sio, M. Gatu Johnson, F. Séguin, J. Frenje, and R. Petrasso (MIT), V. Glebov, C. Stoeckl, J. Delettrez, and C. Sangster (LLE), J. Pino, P. Amendt, C. Bellei, and S. Wilks (LLNL), G. Kagan, N. Hoffmann and K. Molvig (LANL), and A. Nikroo (GA) and was supported in part by the NLUF, FSC/UR, U.S. DOE, LLNL and LLE.

Buoyant Effects on the Flammability of Silicone Samples Planned for the Spacecraft Fire Experiment (Saffire)

NASA Technical Reports Server (NTRS)

Niehaus, Justin; Ferkul, Paul V.; Gokoglu, Suleyman; Ruff, Gary

2015-01-01

Flammability experiments on silicone samples were conducted in anticipation of the Spacecraft Fire Experiment (Saffire). The sample geometry was chosen to match the NASA 6001 Test 1 specification, namely 5 cm wide by 30 cm tall. Four thicknesses of silicone (0.25, 0.36, 0.61 and 1.00 mm) were examined. Tests included traditional upward buoyant flame spread using Test 1 procedures, downward opposed flow flame spread, horizontal and angled flame spread, forced flow upward and downward flame spread. In addition to these configurations, upward and downward tests were also conducted in a chamber with varying oxygen concentrations. In the upward buoyant flame spread tests, the flame generally did not burn the entire sample. As thickness was increased, the flame spread distance decreased before flame extinguishment. For the thickest sample, ignition could not be achieved. In the downward tests, the two thinnest samples permitted the flame to burn the entire sample, but the spread rate was lower compared to the corresponding upward values. The other two thicknesses could not be ignited in the downward configuration. The increased flammability for downward spreading flames relative to upward ones is uncommon. The two thinnest samples also burned completely in the horizontal configuration, as well as at angles up to 75 degrees from the horizontal. The upward and downward flammability behavior was compared in atmospheres of varying oxygen concentration to determine a maximum oxygen concentration for each configuration. Upward tests in air with an added forced flow were more flammable. Complementary analyses using SEM and TGA techniques suggest the importance of the silica layer formed on the burned sample surface. As silicone burns upward, silica deposits downstream •If the silicone is ignited in the downward configuration, it burns the entire length of the sample •Burning upward at an angle increases the burn length in some cases possibly due to less silica deposition •Forced flow in the upward burning case increases flammability, likely due to an increase in convective flow preventing silica from depositing •Samples in upward configuration burning under forced flow self extinguish after forced flow is removed

Effect of energetic electrons on combustion of premixed burner flame

NASA Astrophysics Data System (ADS)

Sasaki, Koichi

2011-10-01

In many studies of plasma-assisted combustion, authors superpose discharges onto flames to control combustion reactions. This work is motivated by more fundamental point of view. The standpoint of this work is that flames themselves are already plasmas. We irradiated microwave power onto premixed burner flame with the intention of heating electrons in it. The microwave power was limited below the threshold for a discharge. We obtained the enhancement of burning velocity by the irradiation of the microwave power, which was understood by the shortening of the flame length. At the same time, we observed the increases in the optical emission intensities of OH and CH radicals. Despite the increases in the optical emission intensities, the optical emission spectra of OH and CH were not affected by the microwave irradiation, indicating that the enhancement of the burning velocity was not attributed to the increase in the gas temperature. On the other hand, we observed significant increase in the optical emission intensity of the second positive system of molecular nitrogen, which is a clear evidence for electron heating in the premixed burner flame. Therefore, it is considered that the enhancement of the burning velocity is obtained by nonequilibrium combustion chemistry which is driven by energetic electrons. By irradiating pulsed microwave power, we examined the time constants for the increases and decreases in the optical emission intensities of N2, OH, CH, and continuum radiation.

Our chemical burn experience: exposing the dangers of anhydrous ammonia.

PubMed

Wibbenmeyer, L A; Morgan, L J; Robinson, B K; Smith, S K; Lewis, R W; Kealey, G P

1999-01-01

Although chemical injuries account for only a small number of one burn unit's cases, the diversity, resulting complications, and sequelae of these burns pose special problems. We reviewed a 19-year period of the chemical burn experience of our burn unit. The population of patients with these types of burns consisted of young men (mean age: 29.8 years), the majority of whom were injured on the job. Unique to our series is the largest collection of injuries (30%) resulting from the common fertilizer anhydrous ammonia. Another population of concern, accounting for 14% of the injuries in our unit, is that of patients injured at home with routine household cleaners. Nearly one half of those patients injured at home incurred injuries that required grafting. The cornerstone of chemical burn prevention and treatment involves education regarding the caustic nature of chemicals, proper handling, adequate protection, and copious irrigation of the wound at the scene. From the analysis of our retrospective review, adequate education and treatment at the scene appear to be well implemented in the industrial and farming communities. The focus of our education efforts should be directed toward the public and emphasize the safe use of household chemicals. Finally our review illuminated the potential benefit of immediate excision and grafting for decreasing the length of stay, complications, and loss of productivity.

Plasma flame for mass purification of contaminated air with chemical and biological warfare agents

NASA Astrophysics Data System (ADS)

Uhm, Han S.; Shin, Dong H.; Hong, Yong C.

2006-09-01

An elimination of airborne simulated chemical and biological warfare agents was carried out by making use of a plasma flame made of atmospheric plasma and a fuel-burning flame, which can purify the interior air of a large volume in isolated spaces such as buildings, public transportation systems, and military vehicles. The plasma flame generator consists of a microwave plasma torch connected in series to a fuel injector and a reaction chamber. For example, a reaction chamber, with the dimensions of a 22cm diameter and 30cm length, purifies an airflow rate of 5000lpm contaminated with toluene (the simulated chemical agent) and soot from a diesel engine (the simulated aerosol for biological agents). Large volumes of purification by the plasma flame will free mankind from the threat of airborne warfare agents. The plasma flame may also effectively purify air that is contaminated with volatile organic compounds, in addition to eliminating soot from diesel engines as an environmental application.

Treatment of acute burn blisters in unscheduled care settings.

PubMed

Payne, Sarah; Cole, Elaine

2012-09-01

Many patients with minor burns present at emergency departments and urgent care centres, where their management is often undertaken by experienced nurses rather than experts in treating burns. This article describes a small study of the clinical decision making that underpins nurses' management of minor burns in these non-specialist settings. The results suggest that, due to a lack of relevant research, nurses base their decisions on previous experience or expert colleagues' opinions and advice rather than on the evidence.

Paediatric electrical burn injuries: experience from a tertiary care burns unit in North India

PubMed Central

Srivastava, S.; Patil, A.N.; Bedi, M.; Tawar, R.S.

2017-01-01

Summary Electrical burn injuries in the paediatric age group constitute a small proportion of all burn cases and cause significant morbidity and long-term psychosocial impact. The objective of this study was to evaluate various aspects of electrical burn injuries in the paediatric age group in our region. A retrospective review was done of all paediatric electrical burns admitted to a tertiary care burns unit over a period of 12 months (January 2016 to December 2016). There were 77 cases of electrical burns under the age of 16 years. High voltage burns predominated and older age groups were more frequently affected. Male:female ratio was 4.1:1. Amputations were required in 18 (23%), skin grafting in 52 (67%) and flap cover in 29 (37%) patients. There were unfavourable outcomes in 32% patients with a mortality rate of 7.8%. Significant association was found between unfavourable outcomes and high voltage burn injuries and length of hospital stay. The impact of electrical burn injuries is substantial and can be reduced by simple preventive measures such as educating parents, improving health infrastructure and adherence to safety regulations.

Smoke inhalation increases intensive care requirements and morbidity in paediatric burns.

PubMed

Tan, Alethea; Smailes, Sarah; Friebel, Thessa; Magdum, Ashish; Frew, Quentin; El-Muttardi, Naguib; Dziewulski, Peter

2016-08-01

Burn survival has improved with advancements in fluid resuscitation, surgical wound management, wound dressings, access to antibiotics and nutritional support for burn patients. Despite these advancements, the presence of smoke inhalation injury in addition to a cutaneous burn still significantly increases morbidity and mortality. The pathophysiology of smoke inhalation has been well studied in animal models. Translation of this knowledge into effectiveness of clinical management and correlation with patient outcomes including the paediatric population, is still limited. We retrospectively reviewed our experience of 13 years of paediatric burns admitted to a regional burn's intensive care unit. We compared critical care requirements and patient outcomes between those with cutaneous burns only and those with concurrent smoke inhalation injury. Smoke inhalation increases critical care requirements and mortality in the paediatric burn population. Therefore, early critical care input in the management of these patients is advised. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

New Fashioned Book Burning.

ERIC Educational Resources Information Center

Gardner, Robert

1997-01-01

Reports on results of a teacher's experiment in book burning as a lesson accompanying the teaching of Ray Bradbury's "Fahrenheit 451." Discusses student reactions and the purpose of or justification for the experimental lesson. (TB)

Multi-energy SXR cameras for magnetically confined fusion plasmas (invited)

NASA Astrophysics Data System (ADS)

Delgado-Aparicio, L. F.; Maddox, J.; Pablant, N.; Hill, K.; Bitter, M.; Rice, J. E.; Granetz, R.; Hubbard, A.; Irby, J.; Greenwald, M.; Marmar, E.; Tritz, K.; Stutman, D.; Stratton, B.; Efthimion, P.

2016-11-01

A compact multi-energy soft x-ray camera has been developed for time, energy and space-resolved measurements of the soft-x-ray emissivity in magnetically confined fusion plasmas. Multi-energy soft x-ray imaging provides a unique opportunity for measuring, simultaneously, a variety of important plasma properties (Te, nZ, ΔZeff, and ne,fast). The electron temperature can be obtained by modeling the slope of the continuum radiation from ratios of the available brightness and inverted radial emissivity profiles over multiple energy ranges. Impurity density measurements are also possible using the line-emission from medium- to high-Z impurities to separate the background as well as transient levels of metal contributions. This technique should be explored also as a burning plasma diagnostic in-view of its simplicity and robustness.

Structure of conducting channel of lightning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alanakyan, Yu. R.

2013-08-15

The spatial distribution of the plasma density in a lightning channel is studied theoretically. It is shown that the electric-field double layer is formed at the channel boundary. In this case, the electron temperature changes abruptly and ions are accelerated by the electric field of the double layer. The ion momentum flux density is close to the surrounding gas pressure. Cleaning of the channel from heavy particles occurs in particle-exchange processes between the plasma channel and the surrounding air. Hydrogen ions are accumulated inside the expanding channel from the surrounding air, which is enriched by hydrogen-contained molecules. In this case,more » the plasma channel is unstable and splits to a chain of equidistant bunches of plasma. The hydrogen-enrich bunches burn diffusely after recombination exhibiting the bead lightning behavior.« less

Stopping power in D6Li plasmas for target ignition studies

NASA Astrophysics Data System (ADS)

Cortez, Ross J.; Cassibry, Jason T.

2018-02-01

The ability to calculate the range of charged fusion products in a target is critical when estimating driver requirements. Additionally, charged particle ranges are a determining factor in the possibility that a burn front will propagate through the surrounding cold fuel layer, igniting the plasma. Performance parameters of the plasma, such as yield, gain, etc therefore rely on accurate knowledge of particle ranges and stopping power over a wide range of densities and temperatures. Further, this knowledge is essential in calculating ignition conditions for a given target design. In this paper, stopping power is calculated for DD and D6Li plasmas using a molecular dynamics based model. Emphasis is placed on solid D6Li which has been recently considered as a fuel option for fusion propulsion systems.

Understorey fire propagation and tree mortality on adjacent areas to an Amazonian deforestation fire

Treesearch

J.A. Carvalho; C.A. Gurgel Veras; E.C. Alvarado; D.V. Sandberg; S.J. Leite; R. Gielow; E.R.C. Rabelo; J.C. Santos

2010-01-01

Fire characteristics in tropical ecosystems are poorly documented quantitatively in the literature. This paper describes an understorey fire propagating across the edges of a biomass burn of a cleared primary forest. The experiment was carried out in 2001 in the Amazon forest near Alta Floresta, state of Mato Grosso, Brazil, as part of biomass burning experiments...

Recent results from experimental studies on laser-plasma coupling in a shock ignition relevant regime

NASA Astrophysics Data System (ADS)

Koester, P.; Antonelli, L.; Atzeni, S.; Badziak, J.; Baffigi, F.; Batani, D.; Cecchetti, C. A.; Chodukowski, T.; Consoli, F.; Cristoforetti, G.; De Angelis, R.; Folpini, G.; Gizzi, L. A.; Kalinowska, Z.; Krousky, E.; Kucharik, M.; Labate, L.; Levato, T.; Liska, R.; Malka, G.; Maheut, Y.; Marocchino, A.; Nicolai, P.; O'Dell, T.; Parys, P.; Pisarczyk, T.; Raczka, P.; Renner, O.; Rhee, Y. J.; Ribeyre, X.; Richetta, M.; Rosinski, M.; Ryc, L.; Skala, J.; Schiavi, A.; Schurtz, G.; Smid, M.; Spindloe, C.; Ullschmied, J.; Wolowski, J.; Zaras, A.

2013-12-01

Shock ignition (SI) is an appealing approach in the inertial confinement scenario for the ignition and burn of a pre-compressed fusion pellet. In this scheme, a strong converging shock is launched by laser irradiation at an intensity Iλ2 > 1015 W cm-2 µm2 at the end of the compression phase. In this intensity regime, laser-plasma interactions are characterized by the onset of a variety of instabilities, including stimulated Raman scattering, Brillouin scattering and the two plasmon decay, accompanied by the generation of a population of fast electrons. The effect of the fast electrons on the efficiency of the shock wave production is investigated in a series of dedicated experiments at the Prague Asterix Laser Facility (PALS). We study the laser-plasma coupling in a SI relevant regime in a planar geometry by creating an extended preformed plasma with a laser beam at ˜7 × 1013 W cm-2 (250 ps, 1315 nm). A strong shock is launched by irradiation with a second laser beam at intensities in the range 1015-1016 W cm-2 (250 ps, 438 nm) at various delays with respect to the first beam. The pre-plasma is characterized using x-ray spectroscopy, ion diagnostics and interferometry. Spectroscopy and calorimetry of the backscattered radiation is performed in the spectral range 250-850 nm, including (3/2)ω, ω and ω/2 emission. The fast electron production is characterized through spectroscopy and imaging of the Kα emission. Information on the shock pressure is obtained using shock breakout chronometry and measurements of the craters produced by the shock in a massive target. Preliminary results show that the backscattered energy is in the range 3-15%, mainly due to backscattered light at the laser wavelength (438 nm), which increases with increasing the delay between the two laser beams. The values of the peak shock pressures inferred from the shock breakout times are lower than expected from 2D numerical simulations. The same simulations reveal that the 2D effects play a major role in these experiments, with the laser spot size comparable with the distance between critical and ablation layers.

Real-time MSE measurements for current profile control on KSTAR.

PubMed

De Bock, M F M; Aussems, D; Huijgen, R; Scheffer, M; Chung, J

2012-10-01

To step up from current day fusion experiments to power producing fusion reactors, it is necessary to control long pulse, burning plasmas. Stability and confinement properties of tokamak fusion reactors are determined by the current or q profile. In order to control the q profile, it is necessary to measure it in real-time. A real-time motional Stark effect diagnostic is being developed at Korean Superconducting Tokamak for Advanced Research for this purpose. This paper focuses on 3 topics important for real-time measurements: minimize the use of ad hoc parameters, minimize external influences and a robust and fast analysis algorithm. Specifically, we have looked into extracting the retardance of the photo-elastic modulators from the signal itself, minimizing the influence of overlapping beam spectra by optimizing the optical filter design and a multi-channel, multiharmonic phase locking algorithm.

Planning for burn disasters: lessons learned from one hundred years of history.

PubMed

Barillo, David J; Wolf, Steven

2006-01-01

The terrorist attacks of September 11th have prompted interest in developing plans to manage thousands of burn casualties. There is little actual experience in the United States in managing disasters of this magnitude. As an alternative, lessons may be learned from the historical experiences of previous civilian burn or fire disasters occurring in this country. A review of relevant medical, fire service, and popular literature pertaining to civilian burn or fire disasters occurring in the United States between the years 1900 and 2000 was performed. In the 20th century, 73 major U.S. fire or burn disasters have occurred. With each disaster prompting a strengthening of fire regulations or building codes, the number of fatalities per incident has steadily decreased. Detailed examination of several landmark fires demonstrated that casualty counts were great but that most victims had fatal injuries and died on the scene or within 24 hours. A second large cohort comprised the walking wounded, who required minimal outpatient treatment. Patients requiring inpatient burn care comprise a small percentage of the total casualty figure but consume enormous resources during hospitalization. Burn mass casualty incidents are uncommon. The number of casualties per incident decreased over time. In most fire disasters, the majority of victims either rapidly die or have minimal injuries and can be treated and released. As a result, most disasters produce fewer than 25 to 50 patients requiring inpatient burn care. This would be a rational point to begin burn center preparations for mass casualty incidents. A robust outpatient capability to manage the walking wounded is also desirable.

Plasma Proteins and Wound Healing

DTIC Science & Technology

1981-11-01

re a p- pea rs to be a transfer of proteases from a lpha ,- antitryp in to a lpha~-macroglobulin (66) and a hi hi preferentia l a nd ra pid uptake...Peripheral blood T and B lymphocytes in pa- tients with burns—II, sequential rosette analyses con- sidering burn severity and pseudomonas sepsis

Source Mechanisms and Radio Effects of Ionospheric Plasma

DTIC Science & Technology

1992-11-01

naturally-occurring ELF hiss simi- lar to that observed on other low-altitude satellites (Gurnett and Burns, 1968; Mosier, 1971; Muzzio and Angerami ...satellite, J. Geophys. Res., 76, 1713, 1971. Muzzio, J.L.R., and J.J. Angerami , OGO 4 observations of ex- tremely low-frequency hiss, J. Geophys. Res

ABA Southern Region Burn disaster plan: the process of creating and experience with the ABA southern region burn disaster plan.

PubMed

Kearns, Randy D; Cairns, Bruce A; Hickerson, William L; Holmes, James H

2014-01-01

The Southern Region of the American Burn Association began to craft a regional plan to address a surge of burn-injured patients after a mass casualty event in 2004. Published in 2006, this plan has been tested through modeling, exercise, and actual events. This article focuses on the process of how the plan was created, how it was tested, and how it interfaces with other ongoing efforts on preparedness. One key to success regarding how people respond to a disaster can be traced to preexisting relationships and collaborations. These activities would include training or working together and building trust long before the crisis. Knowing who you can call and rely on when you need help, within the context of your plan, can be pivotal in successfully managing a disaster. This article describes how a coalition of burn center leaders came together. Their ongoing personal association has facilitated the development of planning activities and has kept the process dynamic. This article also includes several of the building blocks for developing a plan from creation to composition, implementation, and testing. The plan discussed here is an example of linking leadership, relationships, process, and documentation together. On the basis of these experiences, the authors believe these elements are present in other regions. The intent of this work is to share an experience and to offer it as a guide to aid others in their regional burn disaster planning efforts.

Experimental Modeling of the Effect of Terrain Slope on Marginal Burning

Treesearch

X. Zhou; S. Mahalingam; D. Weise

2005-01-01

A series of laboratory fire spread experiments were completed to analyze the effect of terrain slope on marginal burning behavior of live chaparral shrub fuels that grow in the mountains of southern California. We attempted to burn single species fuel beds of four common chaparral plants under various fuel bed configurations and ambient conditions. Seventy-three (or 42...

Bi-Component Droplet Combustion in Reduced Gravity

NASA Technical Reports Server (NTRS)

Shaw, Benjamin D.

2004-01-01

This research deals with reduced-gravity combustion of bi-component droplets initially in the mm size range or larger. The primary objectives of the research are to study the effects of droplet internal flows, thermal and solutal Marangoni stresses, and species volatility differences on liquid species transport and overall combustion phenomena (e.g., gas-phase unsteadiness, burning rates, sooting, radiation, and extinction). The research program utilizes a reduced gravity environment so that buoyancy effects are rendered negligible. Use of large droplets also facilitates visualization of droplet internal flows, which is important for this research. In the experiments, droplets composed of low- and high-volatility species are burned. The low-volatility components are initially present in small amounts. As combustion of a droplet proceeds, the liquid surface mass fraction of the low-volatility component will increase with time, resulting in a sudden and temporary decrease in droplet burning rates as the droplet rapidly heats to temperatures close to the boiling point of the low-volatility component. This decrease in burning rates causes a sudden and temporary contraction of the flame. The decrease in burning rates and the flame contraction can be observed experimentally. Measurements of burning rates as well as the onset time for flame contraction allow effective liquid-phase species diffusivities to be calculated, e.g., using asymptotic theory. It is planned that droplet internal flows will be visualized in flight and ground-based experiments. In this way, effective liquid species diffusivities can be related to droplet internal flow characteristics. This program is a continuation of extensive ground-based experimental and theoretical research on bi-component droplet combustion that has been ongoing for several years. The focal point of this program is a flight experiment (Bi-Component Droplet Combustion Experiment, BCDCE). This flight experiment is under development. However, supporting ground-based studies have been performed. Some of the most recent ground-based research is summarized.

Bi-Component Droplet Combustion in Reduced Gravity

NASA Technical Reports Server (NTRS)

Shaw, B. D.

2001-01-01

This research deals with reduced-gravity combustion of bi-component droplets initially in the mm size range or larger. The primary objectives of the research are to study the effects of droplet internal flows, thermal and solutal Marangoni stresses, and species volatility differences on liquid species transport and overall combustion phenomena (e.g., gas-phase unsteadiness, burning rates, sooting, radiation, and extinction). The research program utilizes a reduced-gravity environment so that buoyancy effects are rendered negligible. Use of large droplets also facilitates visualization of droplet internal flows, which is important for this research. In the experiments, droplets composed of low- and high-volatility species are burned. The low-volatility components are initially present in small amounts. As combustion of a droplet proceeds, the liquid surface mass fraction of the low-volatility component will increase with time, resulting in a sudden and temporary decrease in droplet burning rates as the droplet rapidly heats to temperatures close to the boiling point of the low-volatility component. This decrease in burning rates causes a sudden and temporary contraction of the flame. The decrease in burning rates and the flame contraction can be observed experimentally. Measurements of burning rates as well as the onset time for flame contraction allow effective liquid-phase species diffusivities to be calculated, e.g., using asymptotic theory. It is planned that droplet internal flows will be visualized in future flight and ground-based experiments. In this way, effective liquid species diffusivities can be related to droplet internal flow characteristics. This program is a continuation of extensive ground based experimental and theoretical research on bi-component droplet combustion that has been ongoing for several years. The focal point of this program is a flight experiment (Bi-Component Droplet Combustion Experiment, BCDCE). This flight experiment is under development. However, supporting studies have been performed. Because of space limitations, only some of the research performed over the last two years (since the 5th Microgravity Combustion Workshop) is summarized here.

The introduction of a protocol for the use of biobrane for facial burns in children.

PubMed

Rogers, A D; Adams, S; Rode, H

2011-01-01

BIOBRANE HAS BECOME AN INDISPENSIBLE DRESSING WITH THREE ESTABLISHED INDICATIONS IN ACUTE BURNS CARE AT OUR INSTITUTION: (1) as the definitive dressing of superficial partial thickness facial burns, (2) after tangential excision of deep burns when autograft or cadaver skin is unavailable, and (3) for graft reduction. This paper details our initial experience of Biobrane for the management of superficial partial thickness facial burns in children and the protocol that was compiled for its optimal use. A retrospective analysis of theatre records, case notes and photographs was performed to evaluate our experience with Biobrane over a one-year period. Endpoints included length of stay, analgesic requirements, time to application of Biobrane, healing times, and aesthetic results. Historical controls were used to compare the results with our previous standard of care. 87 patients with superficial partial thickness burns of the face had Biobrane applied during this period. By adhering to the protocol we were able to demonstrate significant reductions in hospital stay, healing time, analgesic requirements, nursing care, with excellent cosmetic results. The protocol is widely accepted by all involved in the optimal management of these patients, including parents, anaesthetists, and nursing staff.

Hydrogen Burning in Low Mass Stars Constrains Scalar-Tensor Theories of Gravity.

PubMed

Sakstein, Jeremy

2015-11-13

The most general scalar-tensor theories of gravity predict a weakening of the gravitational force inside astrophysical bodies. There is a minimum mass for hydrogen burning in stars that is set by the interplay of plasma physics and the theory of gravity. We calculate this for alternative theories of gravity and find that it is always significantly larger than the general relativity prediction. The observation of several low mass red dwarf stars therefore rules out a large class of scalar-tensor gravity theories and places strong constraints on the cosmological parameters appearing in the effective field theory of dark energy.

Stellarator Research Opportunities: A Report of the National Stellarator Coordinating Committee

DOE PAGES

Gates, David A.; Anderson, David; Anderson, S.; ...

2018-02-19

This paper is the product of a stellarator community workshop, organized by the National Stellarator Coordinating Committee and referred to as Stellcon, that was held in Cambridge, Massachusetts in February 2016, hosted by MIT. The workshop was widely advertised, and was attended by 40 scientists from 12 different institutions including national labs, universities and private industry, as well as a representative from the Department of Energy. The final section of this document describes areas of community wide consensus that were developed as a result of the discussions held at that workshop. Areas where further study would be helpful to generatemore » a consensus path forward for the US stellarator program are also discussed. The program outlined in this document is directly responsive to many of the strategic priorities of FES as articulated in “Fusion Energy Sciences: A Ten-Year Perspective (2015–2025)” [1]. The natural disruption immunity of the stellarator directly addresses “Elimination of transient events that can be deleterious to toroidal fusion plasma confinement devices” an area of critical importance for the US fusion energy sciences enterprise over the next decade. Another critical area of research “Strengthening our partnerships with international research facilities,” is being significantly advanced on the W7-X stellarator in Germany and serves as a test-bed for development of successful international collaboration on ITER. Finally, this report also outlines how materials science as it relates to plasma and fusion sciences, another critical research area, can be carried out effectively in a stellarator. Additionally, significant advances along two of the Research Directions outlined in the report; “Burning Plasma Science: Foundations—Next-generation research capabilities”, and “Burning Plasma Science: Long pulse—Sustainment of Long-Pulse Plasma Equilibria” are proposed.« less

Stellarator Research Opportunities: A Report of the National Stellarator Coordinating Committee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gates, David A.; Anderson, David; Anderson, S.

This paper is the product of a stellarator community workshop, organized by the National Stellarator Coordinating Committee and referred to as Stellcon, that was held in Cambridge, Massachusetts in February 2016, hosted by MIT. The workshop was widely advertised, and was attended by 40 scientists from 12 different institutions including national labs, universities and private industry, as well as a representative from the Department of Energy. The final section of this document describes areas of community wide consensus that were developed as a result of the discussions held at that workshop. Areas where further study would be helpful to generatemore » a consensus path forward for the US stellarator program are also discussed. The program outlined in this document is directly responsive to many of the strategic priorities of FES as articulated in “Fusion Energy Sciences: A Ten-Year Perspective (2015–2025)” [1]. The natural disruption immunity of the stellarator directly addresses “Elimination of transient events that can be deleterious to toroidal fusion plasma confinement devices” an area of critical importance for the US fusion energy sciences enterprise over the next decade. Another critical area of research “Strengthening our partnerships with international research facilities,” is being significantly advanced on the W7-X stellarator in Germany and serves as a test-bed for development of successful international collaboration on ITER. Finally, this report also outlines how materials science as it relates to plasma and fusion sciences, another critical research area, can be carried out effectively in a stellarator. Additionally, significant advances along two of the Research Directions outlined in the report; “Burning Plasma Science: Foundations—Next-generation research capabilities”, and “Burning Plasma Science: Long pulse—Sustainment of Long-Pulse Plasma Equilibria” are proposed.« less

Stellarator Research Opportunities: A Report of the National Stellarator Coordinating Committee

NASA Astrophysics Data System (ADS)

Gates, D. A.; Anderson, D.; Anderson, S.; Zarnstorff, M.; Spong, D. A.; Weitzner, H.; Neilson, G. H.; Ruzic, D.; Andruczyk, D.; Harris, J. H.; Mynick, H.; Hegna, C. C.; Schmitz, O.; Talmadge, J. N.; Curreli, D.; Maurer, D.; Boozer, A. H.; Knowlton, S.; Allain, J. P.; Ennis, D.; Wurden, G.; Reiman, A.; Lore, J. D.; Landreman, M.; Freidberg, J. P.; Hudson, S. R.; Porkolab, M.; Demers, D.; Terry, J.; Edlund, E.; Lazerson, S. A.; Pablant, N.; Fonck, R.; Volpe, F.; Canik, J.; Granetz, R.; Ware, A.; Hanson, J. D.; Kumar, S.; Deng, C.; Likin, K.; Cerfon, A.; Ram, A.; Hassam, A.; Prager, S.; Paz-Soldan, C.; Pueschel, M. J.; Joseph, I.; Glasser, A. H.

2018-02-01

This document is the product of a stellarator community workshop, organized by the National Stellarator Coordinating Committee and referred to as Stellcon, that was held in Cambridge, Massachusetts in February 2016, hosted by MIT. The workshop was widely advertised, and was attended by 40 scientists from 12 different institutions including national labs, universities and private industry, as well as a representative from the Department of Energy. The final section of this document describes areas of community wide consensus that were developed as a result of the discussions held at that workshop. Areas where further study would be helpful to generate a consensus path forward for the US stellarator program are also discussed. The program outlined in this document is directly responsive to many of the strategic priorities of FES as articulated in "Fusion Energy Sciences: A Ten-Year Perspective (2015-2025)" [1]. The natural disruption immunity of the stellarator directly addresses "Elimination of transient events that can be deleterious to toroidal fusion plasma confinement devices" an area of critical importance for the US fusion energy sciences enterprise over the next decade. Another critical area of research "Strengthening our partnerships with international research facilities," is being significantly advanced on the W7-X stellarator in Germany and serves as a test-bed for development of successful international collaboration on ITER. This report also outlines how materials science as it relates to plasma and fusion sciences, another critical research area, can be carried out effectively in a stellarator. Additionally, significant advances along two of the Research Directions outlined in the report; "Burning Plasma Science: Foundations - Next-generation research capabilities", and "Burning Plasma Science: Long pulse - Sustainment of Long-Pulse Plasma Equilibria" are proposed.

Stellarator Research Opportunities: A report of the National Stellarator Coordinating Committee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gates, David A.; Anderson, David

This document is the product of a stellarator community workshop, organized by the National Stellarator Coordinating Committee and referred to as Stellcon, that was held in Cambridge, Massachusetts in February 2016, hosted by MIT. The workshop was widely advertised, and was attended by 40 scientists from 12 different institutions including national labs, universities and private industry, as well as a representative from the Department of Energy. The final section of this document describes areas of community wide consensus that were developed as a result of the discussions held at that workshop. Areas where further study would be helpful to generatemore » a consensus path forward for the US stellarator program are also discussed. The program outlined in this document is directly responsive to many of the strategic priorities of FES as articulated in “Fusion Energy Sciences: A Ten-Year Perspective (2015-2025)” [2]. The natural disruption immunity of the stellarator directly addresses “Elimination of transient events that can be deleterious to toroidal fusion plasma confinement devices” an area of critical importance for the U.S. fusion energy sciences enterprise over the next decade. Another critical area of research “Strengthening our partnerships with international research facilities,” is being significantly advanced on the W7-X stellarator in Germany and serves as a test-bed for development of successful international collaboration on ITER. This report also outlines how materials science as it relates to plasma and fusion sciences, another critical research area, can be carried out effectively in a stellarator. Additionally, significant advances along two of the Research Directions outlined in the report; “Burning Plasma Science: Foundations - Next-generation research capabilities”, and “Burning Plasma Science: Long pulse - Sustainment of Long-Pulse Plasma Equilibria” are proposed.« less

Tropospheric O3 over Indonesia during biomass burning events measured with GOME (Global Ozone Monitoring Experiment) and compared with backtrajectory calculation

NASA Astrophysics Data System (ADS)

Ladstaetter-Weissenmayer, A.; Meyer-Arnek, J.; Burrows, J. P.

During the dry season, biomass burning is an important source of ozone precursors for the tropical troposphere, and ozone formation can occur in biomass burning plumes originating in Indonesia and northern Australia. Satellite based GOME (Global Ozone Measuring experiment) data are used to characterize the amount of tropospheric ozone production over this region during the El Niño event in September 1997 compared to a so called "normal" year 1998. Large scale biomass burning occurred over Kalimantan in 1997 caused by the absence of the northern monsoon rains, leading to significant increases in tropospheric ozone. Tropospheric ozone was determined from GOME data using the Tropospheric Excess Method (TEM). Backtrajectory calculations show that Indonesia is influenced every summer by the emissions of trace gases from biomass buring over northern Australia. But in 1997 over Indonesia an increasing of tropospheric ozone amounts can be observed caused by the fires over Indonesia itself as well as by northern Australia. The analysis of the measurements of BIBLE-A (Biomass Burning and Lightning Experiment) and using ATSR (Along the Track Scanning Radiometer) data show differences in the view to the intensity of fire counts and therefore in the amount of the emission of precursors of tropospheric ozone comparing September 1997 to September 1998.

Pentadecapeptide BPC 157 cream improves burn-wound healing and attenuates burn-gastric lesions in mice.

PubMed

Mikus, D; Sikiric, P; Seiwerth, S; Petricevic, A; Aralica, G; Druzijancic, N; Rucman, R; Petek, M; Pigac, B; Perovic, D; Kolombo, M; Kokic, N; Mikus, S; Duplancic, B; Fattorini, I; Turkovic, B; Rotkvic, I; Mise, S; Prkacin, I; Konjevoda, P; Stambuk, N; Anic, T

2001-12-01

The effects of the gastric pentadecapeptide BPC 157 were investigated when administered topically or systemically in burned mice. This agent is known to have a beneficial effect in a variety of models of gastrointestinal lesions, as well as on wound or fracture healing. Deep partial skin thickness burns (1.5x1.5 cm) covering 20% of total body area, were induced under anesthesia on the back of mice by controlled burning and gastric lesions were assessed 1, 2, 3, 7, 14 and 21 days following injury. The first application of BPC 157 was immediately following burning, and thereafter, once daily, until 24 h before sacrifice. In the initial experiments, exposure to direct flame for 5 s, the BPC 157 was applied at 10 microg or 10 ng/kg b.w. intraperitoneally (i.p.) by injection or alternatively, topically, at the burn, as a thin layer of cream (50 microg of BPC 157 dissolved in 2 ml of distilled water was mixed with 50 g of commercial neutral cream (also used as local vehicle-control)), while silver sulfadiazine 1% cream was a standard agent acting locally. Others received no local medication: they were treated i.p. by injection of distilled water (distilled water-control) or left without any medication (control). In subsequent experiments involving deeper burns (direct flame for 7 s), BPC 157 creams (50 microg, 5 microg, 500 ng, 50 ng or 5 ng of BPC 157 dissolved in 2 ml of distilled water was mixed with 50 g of commercial neutral cream), or vehicle as a thin layer of cream, were applied topically, at the burn. Compared with untreated controls, in both experiments, in the BPC 157 cream-treated mice all parameters of burn healing were improved throughout the experiment: less edema was observed and inflammatory cell numbers decreased. Less necrosis was seen with an increased number of capillaries along with an advanced formation of dermal reticulin and collagen fibers. An increased number of preserved follicles were observed. Two weeks after injury, BPC 157 cream-treated mice completely reversed the otherwise poor re-epithelization ratio noted in the untreated control or mice treated with vehicle only. Tensiometry investigation showed an increased breaking strength and relative elongation of burned skin, while water content in burned skin decreased. This was, however, not the case with the vehicle or silver sulfadiazine. Relative to the control values, in silver sulfadiazine cream-treated mice, only collagen fiber formation was increased, in addition to a decreased inflammatory cell number. Relative to control values, BPC 157 given i.p. decreased the number of inflammatory cells, lowered water content in burned skin, and raised breaking strength and relative elongation of burned skin during tensiometry. Through the experimental period, gastric lesions were continuously noted in all thermally injured mice left without local medication and they were consistently attenuated only by BPC 157 treatments: either given i.p. (at either dose), or given locally (at either concentration). Other treatments (i.e. local treatment with silver sulfadiazine cream or neutral cream in mice subjected for 5 s to direct flame), led to only poor, if any attenuation. This stable gastric pentadecapeptide appears to be active and gives a stimulation to burn healing at the defect site. The agent may act by causing an upregulation of the growth factors, as well as influencing other local factors.

Computational investigations of low-emission burner facilities for char gas burning in a power boiler

NASA Astrophysics Data System (ADS)

Roslyakov, P. V.; Morozov, I. V.; Zaychenko, M. N.; Sidorkin, V. T.

2016-04-01

Various variants for the structure of low-emission burner facilities, which are meant for char gas burning in an operating TP-101 boiler of the Estonia power plant, are considered. The planned increase in volumes of shale reprocessing and, correspondingly, a rise in char gas volumes cause the necessity in their cocombustion. In this connection, there was a need to develop a burner facility with a given capacity, which yields effective char gas burning with the fulfillment of reliability and environmental requirements. For this purpose, the burner structure base was based on the staging burning of fuel with the gas recirculation. As a result of the preliminary analysis of possible structure variants, three types of early well-operated burner facilities were chosen: vortex burner with the supply of recirculation gases into the secondary air, vortex burner with the baffle supply of recirculation gases between flows of the primary and secondary air, and burner facility with the vortex pilot burner. Optimum structural characteristics and operation parameters were determined using numerical experiments. These experiments using ANSYS CFX bundled software of computational hydrodynamics were carried out with simulation of mixing, ignition, and burning of char gas. Numerical experiments determined the structural and operation parameters, which gave effective char gas burning and corresponded to required environmental standard on nitrogen oxide emission, for every type of the burner facility. The burner facility for char gas burning with the pilot diffusion burner in the central part was developed and made subject to computation results. Preliminary verification nature tests on the TP-101 boiler showed that the actual content of nitrogen oxides in burner flames of char gas did not exceed a claimed concentration of 150 ppm (200 mg/m3).

MM-wave cyclotron auto-resonance maser for plasma heating

NASA Astrophysics Data System (ADS)

Ceccuzzi, S.; Dattoli, G.; Di Palma, E.; Doria, A.; Gallerano, G. P.; Giovenale, E.; Mirizzi, F.; Spassovsky, I.; Ravera, G. L.; Surrenti, V.; Tuccillo, A. A.

2014-02-01

Heating and Current Drive systems are of outstanding relevance in fusion plasmas, magnetically confined in tokamak devices, as they provide the tools to reach, sustain and control burning conditions. Heating systems based on the electron cyclotron resonance (ECRH) have been extensively exploited on past and present machines DEMO, and the future reactor will require high frequencies. Therefore, high power (≥1MW) RF sources with output frequency in the 200 - 300 GHz range would be necessary. A promising source is the so called Cyclotron Auto-Resonance Maser (CARM). Preliminary results of the conceptual design of a CARM device for plasma heating, carried out at ENEA-Frascati will be presented together with the planned R&D development.

Summary of ECE presentations at EC-18

DOE PAGES

Taylor, G.

2015-03-12

There were nine ECE and one EBE presentation at EC-18. Four of the presentations were on various aspects of ECE on ITER. The ITER ECE diagnostic has entered an important detailed preliminary design phase and faces several design challenges in the next 2-3 years. Most of the other ECE presentations at the workshop were focused on applications of ECE diagnostics to plasma measurements, rather than improvements in technology, although it was apparent that heterodyne receiver technology continues to improve. CECE, ECE imaging and EBE imaging are increasingly providing valuable insights into plasma behavior that is important to understand if futuremore » burning plasma devices, such as ITER, FNSF and DEMO, are to be successful.« less

Therapeutic effects of transdermal systems containing zinc-related materials on thermal burn rats.

PubMed

Otsuka, Makoto; Hatakeyama, Haruna; Shikamura, Masayuki; Otsuka, Kuniko; Ito, Atsuo

2015-01-01

The aim of the present study is to evaluate the efficacy of slow zinc (Zn) release from β-tricalcium phosphate powder (ZnTCP) containing 10 mol% Zn on rats with thermal burns. The first-aid tapes were contained zinc sulfate (ZnSO4) solution, ZnTCP suspensions or zinc oxide ointment. After thermal burn treatments were performed on Zn-deficient rats, the groups D1, D2 and D3 were treated with tapes containing ZnTCP, ZnSO4 and zinc oxide ointment. The effects of the tapes on wound area, plasma Zn levels and alkaline phosphatase activity (Alp) were investigated. The wound area profiles of all rat groups could be separated into before and after the scab formation at around day 6. The area under the curve (Aw-AUC) for wound area profiles, therefore, was evaluated as an index of therapeutic scores for the thermal wound. The order of Aw-AUC was D3>C>D2>D1. The degree of expansion at the initial stage by thermal burns of group D1 was the lowest and that of group D2 was the highest, and the order was D1

Overview of the South American biomass burning analysis (SAMBBA) field experiment

NASA Astrophysics Data System (ADS)

Morgan, W. T.; Allan, J. D.; Flynn, M.; Darbyshire, E.; Hodgson, A.; Johnson, B. T.; Haywood, J. M.; Freitas, S.; Longo, K.; Artaxo, P.; Coe, H.

2013-05-01

Biomass burning represents one of the largest sources of particulate matter to the atmosphere, which results in a significant perturbation to the Earth's radiative balance coupled with serious negative impacts on public health. Globally, biomass burning aerosols are thought to exert a small warming effect of 0.03 Wm-2, however the uncertainty is 4 times greater than the central estimate. On regional scales, the impact is substantially greater, particularly in areas such as the Amazon Basin where large, intense and frequent burning occurs on an annual basis for several months (usually from August-October). Furthermore, a growing number of people live within the Amazon region, which means that they are subject to the deleterious effects on their health from exposure to substantial volumes of polluted air. Initial results from the South American Biomass Burning Analysis (SAMBBA) field experiment, which took place during September and October 2012 over Brazil, are presented here. A suite of instrumentation was flown on-board the UK Facility for Airborne Atmospheric Measurement (FAAM) BAe-146 research aircraft and was supported by ground based measurements, with extensive measurements made in Porto Velho, Rondonia. The aircraft sampled a range of conditions with sampling of fresh biomass burning plumes, regional haze and elevated biomass burning layers within the free troposphere. The physical, chemical and optical properties of the aerosols across the region will be characterized in order to establish the impact of biomass burning on regional air quality, weather and climate.

Assesment of PM2.5 emission from corn stover burning determining in chamber combustion

NASA Astrophysics Data System (ADS)

Hafidawati; Lestari, P.; Sofyan, A.

2018-04-01

Chamber measurement were conducted to determine Particulate Matter (PM2.5) emission from open burning of corn straw at Garut District, West Java. The of this study is to estimate the concentration of PM2.5 for two types of corn (corncobs and cornstover) for five varieties (Bisma, P29, NK, Bisma, NW). Corn residues were collected and then burned in the chamber combustion. The chamber was designed to simulate the burning in the field, which was observed in the field experiment that meteorological condition was calm wind. The samples were collected using a minivol air sampler. The assessment results of PM2.5 concentrations (mg/m3) from open burning experiment in the chamber for five varieties of corn cobs (Bisma, P29, NK, Bisi, NW) was 9.187; 2.843; 7.409; 3.781; 1.895 respectively. Concentration for corn stover burn was 2.060; 5.283; 4.048; 5.306 and 5.697 respectively. Fluctuations in the value of concentration among these varieties reflect variations in combustion conditions (combustion efficiency) and other parameters including water content, biomass conditions and the meteorological conditions. The combustion efficiency (MCE) of the combustion chamber simulation of corncobs ia lower than the MCE of corn stover, that the concentration PM2.5 more emitted from the burning of corn stover. The results of this study presented provide useful information for the development of local emission factors for PM2.5 from open burning of corn stover in Indonesia.

Validating predictive models for fast ion profile relaxation in burning plasmas

NASA Astrophysics Data System (ADS)

Gorelenkov, N. N.; Heidbrink, W. W.; Kramer, G. J.; Lestz, J. B.; Podesta, M.; Van Zeeland, M. A.; White, R. B.

2016-11-01

The redistribution and potential loss of energetic particles due to MHD modes can limit the performance of fusion plasmas by reducing the plasma heating rate. In this work, we present validation studies of the 1.5D critical gradient model (CGM) for Alfvén eigenmode (AE) induced EP transport in NSTX and DIII-D neutral beam heated plasmas. In previous comparisons with a single DIII-D L-mode case, the CGM model was found to be responsible for 75% of measured AE induced neutron deficit [1]. A fully kinetic HINST is used to compute mode stability for the non-perturbative version of CGM (or nCGM). We have found that AEs show strong local instability drive up to γ /ω ∼ 20% violating assumptions of perturbative approaches used in NOVA-K code. We demonstrate that both models agree with each other and both underestimate the neutron deficit measured in DIII-D shot by approximately a factor of 2. On the other hand in NSTX the application of CGM shows good agreement for the measured flux deficit predictions. We attempt to understand these results with the help of the so-called kick model which is based on the guiding center code ORBIT. The kick model comparison gives important insight into the underlying velocity space dependence of the AE induced EP transport as well as it allows the estimate of the neutron deficit in the presence of the low frequency Alfvénic modes. Within the limitations of used models we infer that there are missing modes in the analysis which could improve the agreement with the experiments.

Overview of the JET results with the ITER-like wall

NASA Astrophysics Data System (ADS)

Romanelli, F.; EFDA Contributors, JET

2013-10-01

Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Zeff (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H98,y2 close to 1 and βN ˜ 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.

EU Development of High Heat Flux Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linke, J.; Lorenzetto, P.; Majerus, P.

2005-04-15

The development of plasma facing components for next step fusion devices in Europe is strongly focused to ITER. Here a wide spectrum of different design options for the divertor target and the first wall have been investigated with tungsten, CFC, and beryllium armor. Electron beam simulation experiments have been used to determine the performance of high heat flux components under ITER specific thermal loads. Beside thermal fatigue loads with power density levels up to 20 MWm{sup -2}, off-normal events are a serious concern for the lifetime of plasma facing components. These phenomena are expected to occur on a time scalemore » of a few milliseconds (plasma disruptions) or several hundred milliseconds (vertical displacement events) and have been identified as a major source for the production of neutron activated metallic or tritium enriched carbon dust which is of serious importance from a safety point of view.The irradiation induced material degradation is another critical concern for future D-T-burning fusion devices. In ITER the integrated neutron fluence to the first wall and the divertor armour will remain in the order of 1 dpa and 0.7 dpa, respectively. This value is low compared to future commercial fusion reactors; nevertheless, a nonnegligible degradation of the materials has been detected, both for mechanical and thermal properties, in particular for the thermal conductivity of carbon based materials. Beside the degradation of individual material properties, the high heat flux performance of actively cooled plasma facing components has been investigated under ITER specific thermal and neutron loads.« less

Kinetic physics in ICF: present understanding and future directions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rinderknecht, Hans G.; Amendt, P. A.; Wilks, S. C.

Kinetic physics has the potential to impact the performance of indirect-drive inertial confinement fusion (ICF) experiments. Systematic anomalies in the National Ignition Facility implosion dataset have been identified in which kinetic physics may play a role, including inferred missing energy in the hohlraum, drive asymmetry in near-vacuum hohlraums, low areal density and high burn-averaged ion temperatures (T i ) compared with mainline simulations, and low ratios of the DD-neutron and DT-neutron yields and inferred T i . Several components of ICF implosions are likely to be influenced or dominated by kinetic physics: laser-plasma interactions in the LEH and hohlraum interior;more » the hohlraum wall blowoff, blowoff/gas and blowoff/ablator interfaces; the ablator and ablator/ice interface; and the DT fuel all present conditions in which kinetic physics can significantly affect the dynamics. This review presents the assembled experimental data and simulation results to date, which indicate that the effects of long mean-free-path plasma phenomena and self-generated electromagnetic fields may have a significant impact in ICF targets. Finally, simulation and experimental efforts are proposed to definitively quantify the importance of these effects at ignition-relevant conditions, including priorities for ongoing study.« less

Kinetic physics in ICF: present understanding and future directions

DOE PAGES

Rinderknecht, Hans G.; Amendt, P. A.; Wilks, S. C.; ...

2018-03-19

Kinetic physics has the potential to impact the performance of indirect-drive inertial confinement fusion (ICF) experiments. Systematic anomalies in the National Ignition Facility implosion dataset have been identified in which kinetic physics may play a role, including inferred missing energy in the hohlraum, drive asymmetry in near-vacuum hohlraums, low areal density and high burn-averaged ion temperatures (T i ) compared with mainline simulations, and low ratios of the DD-neutron and DT-neutron yields and inferred T i . Several components of ICF implosions are likely to be influenced or dominated by kinetic physics: laser-plasma interactions in the LEH and hohlraum interior;more » the hohlraum wall blowoff, blowoff/gas and blowoff/ablator interfaces; the ablator and ablator/ice interface; and the DT fuel all present conditions in which kinetic physics can significantly affect the dynamics. This review presents the assembled experimental data and simulation results to date, which indicate that the effects of long mean-free-path plasma phenomena and self-generated electromagnetic fields may have a significant impact in ICF targets. Finally, simulation and experimental efforts are proposed to definitively quantify the importance of these effects at ignition-relevant conditions, including priorities for ongoing study.« less

Kinetic physics in ICF: present understanding and future directions

NASA Astrophysics Data System (ADS)

Rinderknecht, Hans G.; Amendt, P. A.; Wilks, S. C.; Collins, G.

2018-06-01

Kinetic physics has the potential to impact the performance of indirect-drive inertial confinement fusion (ICF) experiments. Systematic anomalies in the National Ignition Facility implosion dataset have been identified in which kinetic physics may play a role, including inferred missing energy in the hohlraum, drive asymmetry in near-vacuum hohlraums, low areal density and high burn-averaged ion temperatures (〈Ti 〉) compared with mainline simulations, and low ratios of the DD-neutron and DT-neutron yields and inferred 〈Ti 〉. Several components of ICF implosions are likely to be influenced or dominated by kinetic physics: laser-plasma interactions in the LEH and hohlraum interior; the hohlraum wall blowoff, blowoff/gas and blowoff/ablator interfaces; the ablator and ablator/ice interface; and the DT fuel all present conditions in which kinetic physics can significantly affect the dynamics. This review presents the assembled experimental data and simulation results to date, which indicate that the effects of long mean-free-path plasma phenomena and self-generated electromagnetic fields may have a significant impact in ICF targets. Simulation and experimental efforts are proposed to definitively quantify the importance of these effects at ignition-relevant conditions, including priorities for ongoing study.

Simulation of Chirping Avalanche in Neighborhood of TAE gap

NASA Astrophysics Data System (ADS)

Berk, Herb; Breizman, Boris; Wang, Ge; Zheng, Linjin

2016-10-01

A new kinetic code, CHIRP, focuses on the nonlinear response of resonant energetic particles (EPs) that destabilize Alfven waves which then can produce hole and clump phase space chirping structures, while the background plasma currents are assumed to respond linearly to the generated fields. EP currents are due to the motion arising from the perturbed field that is time averaged over an equilibrium orbit. A moderate EP source produces TAE chirping structures that have a limited range of chirping that do not reach the continuum. When the source is sufficiently strong, an EPM is excited in the lower continuum and it chirps rapidly downward as its amplitude rapidly grows in time. This response resembles the experimental observation of an avalanche, which occurs after a series of successive chirping events with a modest frequency shift, and then suddenly a rapid large amplitude and rapid frequency burst to low frequency with the loss of EPs. From these simulation observations we propose that in the experiment the EP population is slowly increasing to the point where the EPM is eventually excited. Supported by SCIDAC Center for Nonlinear Simulation of Energetic Particles Burning Plasmas (CSEP).

Central Safety Factor and Normalized Beta Control Under Near-Zero Input Torque Constraints in DIII-D

NASA Astrophysics Data System (ADS)

Pajares, Andres; Wehner, William; Schuster, Eugenio; Burrell, Keith; Ferron, John; Walker, Michael; Humphreys, David; Lehigh University Team; Atomics Team, General

2017-10-01

DIII-D experiments have assessed the capability of combined central safety factor (q0) and normalized beta (βN) control under near-zero net torque to facilitate access to QH-mode with reverse Ip and normal Bt. Regulation of q0 and βN can prevent magneto-hydrodynamic instabilities that deteriorate plasma performance in discharges with a monotonically increasing safety-factor profile. Zero-input-torque scenarios are of special interest because future burning plasma tokamaks such as ITER will most likely operate with very low input torque, which makes these scenarios more susceptible to locked modes. To support studies of such scenarios, a controller for simultaneous regulation of q0 and βN has been developed using near-zero net input torque actuators including balanced neutral beam injection (NBI) and electron-cyclotron heating & current drive (ECH/ECCD). Experimental results show that in spite of the presence of locked modes the use of feedback control resulted in good tracking of the commanded q0 and βN when both ECCD/ECH and NBI were available. Supported by the US DOE under DE-SC0010661 and DE-FC02-04ER54698.

High Resolution Gamma Ray Spectroscopy at MHz Counting Rates With LaBr3 Scintillators for Fusion Plasma Applications

NASA Astrophysics Data System (ADS)

Nocente, M.; Tardocchi, M.; Olariu, A.; Olariu, S.; Pereira, R. C.; Chugunov, I. N.; Fernandes, A.; Gin, D. B.; Grosso, G.; Kiptily, V. G.; Neto, A.; Shevelev, A. E.; Silva, M.; Sousa, J.; Gorini, G.

2013-04-01

High resolution γ-ray spectroscopy measurements at MHz counting rates were carried out at nuclear accelerators, combining a LaBr 3(Ce) detector with dedicated hardware and software solutions based on digitization and off-line analysis. Spectra were measured at counting rates up to 4 MHz, with little or no degradation of the energy resolution, adopting a pile up rejection algorithm. The reported results represent a step forward towards the final goal of high resolution γ-ray spectroscopy measurements on a burning plasma device.

Electron-ion relaxation in a dense plasma. [supernovae core physics

NASA Technical Reports Server (NTRS)

Littleton, J. E.; Buchler, J.-R.

1974-01-01

The microscopic physics of the thermonuclear runaway in highly degenerate carbon-oxygen cores is investigated to determine if and how a detonation wave is generated. An expression for the electron-ion relaxation time is derived under the assumption of large degeneracy and extreme relativity of the electrons in a two-temperature plasma. Since the nuclear burning time proves to be several orders of magnitude shorter than the relaxation time, it is concluded that in studying the structure of the detonation wave the electrons and ions must be treated as separate fluids.

Modeling of the jack rabbit series of experiments with a temperature based reactive burn model

NASA Astrophysics Data System (ADS)

Desbiens, Nicolas

2017-01-01

The Jack Rabbit experiments, performed by Lawrence Livermore National Laboratory, focus on detonation wave corner turning and shock desensitization. Indeed, while important for safety or charge design, the behaviour of explosives in these regimes is poorly understood. In this paper, our temperature based reactive burn model is calibrated for LX-17 and compared to the Jack Rabbit data. It is shown that our model can reproduce the corner turning and shock desensitization behaviour of four out of the five experiments.

TSG-6 secreted by human umbilical cord-MSCs attenuates severe burn-induced excessive inflammation via inhibiting activations of P38 and JNK signaling.

PubMed

Liu, Lingying; Song, Huifeng; Duan, Hongjie; Chai, Jiake; Yang, Jing; Li, Xiao; Yu, Yonghui; Zhang, Xulong; Hu, Xiaohong; Xiao, Mengjing; Feng, Rui; Yin, Huinan; Hu, Quan; Yang, Longlong; Du, Jundong; Li, Tianran

2016-07-22

The hMSCs have become a promising approach for inflammation treatment in acute phase. Our previous study has demonstrated that human umbilical cord-MSCs could alleviate the inflammatory reaction of severely burned wound. In this study, we further investigated the potential role and mechanism of the MSCs on severe burn-induced excessive inflammation. Wistar rats were randomly divided into following groups: Sham, Burn, Burn+MSCs, Burn+MAPKs inhibitors, and Burn, Burn+MSCs, Burn+Vehicle, Burn+siTSG-6, Burn+rhTSG-6 in the both experiments. It was found that MSCs could only down-regulate P38 and JNK signaling, but had no effect on ERK in peritoneal macrophages of severe burn rats. Furthermore, suppression of P38 and JNK activations significantly reduced the excessive inflammation induced by severe burn. TSG-6 was secreted by MSCs using different inflammatory mediators. TSG-6 from MSCs and recombinant human (rh)TSG-6 all significantly reduced activations of P38 and JNK signaling induced by severe burn and then attenuated excessive inflammations. On the contrary, knockdown TSG-6 in the cells significantly increased phosphorylation of P38 and JNK signaling and reduced therapeutic effect of the MSCs on excessive inflammation. Taken together, this study suggested TSG-6 from MSCs attenuated severe burn-induced excessive inflammation via inhibiting activation of P38 and JNK signaling.

Burning a Candle in a Vessel, a Simple Experiment with a Long History

ERIC Educational Resources Information Center

Vera, Francisco; Rivera, Rodrigo; Nunez, Cesar

2011-01-01

The experiment in which a candle is burned inside an inverted vessel partially immersed in water has a history of more than 2,200 years, but even nowadays it is common that students and teachers relate the change in volume of the enclosed air to its oxygen content. Contrary to what many people think, Lavoisier concluded that any change in volume…

A review of campfire burns in children: The QLD experience.

PubMed

Okon, O; Zhu, L; Kimble, R M; Stockton, K A

2018-03-27

Campfire burns in children are a significant health issue. It is imperative that the extent of the problem is examined and strategies discussed to inform future prevention campaigns. A retrospective review of data from the Queensland Paediatric Burns Registry for all children presenting with campfire burns between January 2013 and December 2014 (inclusive). Information collected included patient demographics, detail regarding mechanism of injury, first aid, Total Body Surface Area (TBSA), burn depth, and treatment. Seventy-five children with campfire burns were seen in our paediatric burns centre during this 2-year period. The median age of patients was 3 years (range 10 days-14 years). The hands and feet were the areas most commonly affected. Eleven percent of patients suffered flame burns, whilst 89% suffered contact burns from the hot coals or ashes. Of the latter group, approximately half experienced burns from campfires that had been extinguished for at least one night. Thirteen percent of patients underwent split thickness skin grafting. The incidence of burns was increased during school holiday months. We have previously demonstrated the effectiveness of targeted campaigns in reducing the incidence of campfire burns. A significant portion of patients sustained burns from incorrectly extinguished campfires. These injuries are likely to be preventable with ongoing public awareness campaigns. Copyright © 2018 Elsevier Ltd and ISBI. All rights reserved.

Video-Enhanced Telemedicine Improves the Care of Acutely Injured Burn Patients in a Rural State.

PubMed

Wibbenmeyer, Lucy; Kluesner, Karen; Wu, Hongqian; Eid, Anas; Heard, Jason; Mann, Benjamin; Pauley, Alison; Peek-Asa, Corrine

The acute care of burn patients is critical and can be a daunting experience for emergency personnel because of the scarcity of burn injuries. Telemedicine that incorporates a visual component can provide immediate expertise in the treatment and management of these injuries. The authors sought to evaluate the addition of video telemedicine to our current telephone burn transfer program. During a 2-year period, 282 patients, 59.4% of all burn patients transferred from outside hospitals, were enrolled in the study. In addition to the scripted call with the charge nurse (ChargeRN) and the accepting physician, nine hospitals also transmitted video images of the wounds before transfer as part of a store and forward telemedicine transfer program (77, 27.6%). The accuracy of burn size estimations (BSA burned) and management changes (fluid requirements, transfer mode, and final disposition) were analyzed between the telephones-only sites (T only) and the video-enhanced sites. Referringstaff participating in video-enhanced telemedicine were sent a Google survey assessing their experience the following day. The referring staff (Referringstaff) was correct in their burn assessment 20% of the time. Video assessment improved the ChargeRN BSA burned and resulted in more accurate fluid resuscitation (P = .030), changes in both transportation mode (P = .042), and disposition decisions (P = .20). The majority of the Referringstaff found that video-enhanced telemedicine helped them communicate with the burn staff more effectively (3.4 ± 0.37, scale 1-4). This study reports the successful implementation of video-enhanced telemedicine pilot project in a rural state. Video-enhanced telemedicine using a store and forward process improved burn size estimation and facilitated management changes. Although not quantitatively assessed, the low cost of the system coupled with the changes in transportation and disposition strongly suggests a decrease in healthcare costs associated with the addition of video to a telephone-only transfer program.

Relative importance of fuel management, ignition management and weather for area burned: Evidence from five landscape-fire-succession models

Treesearch

Geoffrey J. Cary; Mike D. Flannigan; Robert E. Keane; Ross A. Bradstock; Ian D. Davies; James M. Lenihan; Chao Li; Kimberley A. Logan; Russell A. Parsons

2009-01-01

The behaviour of five landscape fire models (CAFE, FIRESCAPE, LAMOS(HS), LANDSUM and SEMLAND) was compared in a standardised modelling experiment. The importance of fuel management approach, fuel management effort, ignition management effort and weather in determining variation in area burned and number of edge pixels burned (a measure of potential impact on assets...

The Incidence of Burns Among Sex-Trafficking Victims in India

PubMed Central

Rahman, Nadia; Sinha, Indranil; Husain, Fatima; Shah, Ajul; Patel, Anup

2014-01-01

Sex trafficking remains a flagrant violation of human rights, creating many public health concerns. During the initiation period, these victims experience acts of violence including gang rapes, subjecting them to traumatic injuries that include burns. Furthermore, lack of access to health care, particularly surgical, keeps them from receiving treatment for these functionally debilitating contractures caused by burns. This piece provides an overview of burns among sex-trafficked victims in India and the efforts by Cents of Relief to address the associated surgical burden of disease. PMID:25191142

Getting Past Dax.

PubMed

Gerrek, Monica L

2018-06-01

Much has been written about Dax Cowart's tragic burn injury, treatment, and recovery. While Dax's case is certainly important to conversations regarding decision making in burn care, his is not the only story there is. In this article, the case of Andrea Rubin, also a severe burn survivor, is introduced as another voice in this conversation. Her experience during treatment and recovery is very different from Dax's and should cause us to at least pause and reconsider how we think about treatment and decision making in burn care. © 2018 American Medical Association. All Rights Reserved.

Management of facial burns with a collagen/glycosaminoglycan skin substitute-prospective experience with 12 consecutive patients with large, deep facial burns.

PubMed

Klein, Matthew B; Engrav, Loren H; Holmes, James H; Friedrich, Jeffrey B; Costa, Beth A; Honari, Shari; Gibran, Nicole S

2005-05-01

Management of deep facial burns remains one of the greatest challenges in burn care. We have developed a protocol over the past 20 years for management of facial burns that includes excision and coverage with thick autograft. However, the results were not perfect. Deformities of the eyelids, nose and mouth as well as the prominence of skin graft junctures demonstrated the need to explore novel approaches. Integra has been used with success in the management of burns of the trunk and extremities. The purpose of this study was to prospectively evaluate the aesthetic outcome of the use of Integra for deep facial burns. Twelve consecutive patients underwent excision of large, deep facial burns and placement of Integra. Integra provides excellent color and minimally visible skin graft junctures. The texture is good but not as supple as thick autograft. Integra is not well suited for use in the coverage of eyelid burns due to the need to wait 2 weeks for adequate vascularization. In summary, thick autograft remains the gold standard for deep facial burns. However, for patients with extensive burns and limited donor sites, Integra provides an acceptable alternative.

Overview of 2010-2013 spring campaigns of Seven South East Asian Studies (7-SEAS) in the northern Southeast Asia

NASA Astrophysics Data System (ADS)

Lin, N.; Tsay, S.; Hsu, N. C.; Holben, B. N.; Anh, N.; Reid, J. S.; Sheu, G.; Chi, K.; Wang, S.; Lee, C.; Wang, L.; Wang, J.; Chen, W.; Welton, E. J.; Liang, S.; Sopajaree, K.; Maring, H. B.; Janjai, S.; Chantara, S.

2013-12-01

The Seven South East Asian Studies (7-SEAS) is a grass-root program and seeks to perform interdisciplinary research in the field of aerosol-meteorology and climate interaction in the Southeast Asian region, particularly for the impact of biomass burning on cloud, atmospheric radiation, hydrological cycle, and regional climate. Participating countries include Indonesia, Malaysia, Philippines, Singapore, Thailand, Taiwan, Vietnam, and USA. A series of field experiments have been conducted during springtime biomass burning seasons in northern Southeast Asia, i.e., Dongsha Experiment in 2010, Son La Campaigns in 2011 and 2012, and BASELInE (Biomass-burning Aerosols & Stratocumulus Environment: Lifecycles and Interactions Experiment) in 2013, respectively. Given an example, during 2010 Dongsha Experiment, a monitoring network for ground-based measurements was established, including five stations from northern Thailand and central Vietnam to Taiwan, with a supersite at the Dongsha Island (i.e. Pratas Island) in South China Sea (or East Sea). Aerosol chemistry sampling was performed for each station for characterizing the compositions of PM2.5/PM10 (some for TSP) including water-soluble ions, metal elements, BC/OC, Hg and dioxins. This experiment provides a relatively complete and first dataset of aerosol chemistry and physical observations conducted in the source/sink region for below marine boundary layer and lower free troposphere of biomass burning/air pollutants in the northern SE Asia. This presentation will give an overview of these 7-SEAS activities and their results, particularly for the characterization of biomass-burning aerosol at source regions in northern Thailand and northern Vietnam, and receptor stations in Taiwan, which is rarely studied.

[Factor XIII-guided treatment algorithm reduces blood transfusion in burn surgery].

PubMed

Carneiro, João Miguel Gonçalves Valadares de Morais; Alves, Joana; Conde, Patrícia; Xambre, Fátima; Almeida, Emanuel; Marques, Céline; Luís, Mariana; Godinho, Ana Maria Mano Garção; Fernandez-Llimos, Fernando

Major burn surgery causes large hemorrhage and coagulation dysfunction. Treatment algorithms guided by ROTEM ® and factor VIIa reduce the need for blood products, but there is no evidence regarding factor XIII. Factor XIII deficiency changes clot stability and decreases wound healing. This study evaluates the efficacy and safety of factor XIII correction and its repercussion on transfusion requirements in burn surgery. Randomized retrospective study with 40 patients undergoing surgery at the Burn Unit, allocated into Group A those with factor XIII assessment (n = 20), and Group B, those without assessment (n = 20). Erythrocyte transfusion was guided by a hemoglobin trigger of 10g.dL -1 and the other blood products by routine coagulation and ROTEM ® tests. Analysis of blood product consumption included units of erythrocytes, fresh frozen plasma, platelets, and fibrinogen. The coagulation biomarker analysis compared the pre- and post-operative values. Group A (with factor XIII study) and Group B had identical total body surface area burned. All patients in Group A had a preoperative factor XIII deficiency, whose correction significantly reduced units of erythrocyte concentrate transfusion (1.95 vs. 4.05, p = 0.001). Pre- and post-operative coagulation biomarkers were similar between groups, revealing that routine coagulation tests did not identify factor XIII deficiency. There were no recorded thromboembolic events. Correction of factor XIII deficiency in burn surgery proved to be safe and effective for reducing perioperative transfusion of erythrocyte units. Copyright © 2017 Sociedade Brasileira de Anestesiologia. Publicado por Elsevier Editora Ltda. All rights reserved.

Measurement of Trace Metals in Tobacco and Cigarette Ash by Inductively Coupled Plasma-Atomic Emission Spectroscopy

NASA Astrophysics Data System (ADS)

Wang, W.; Finlayson-Pitts, B. J.

2003-01-01

The ICP AES experiment reported here is suitable for use in a junior- or senior-level undergraduate instrumental analysis laboratory. The objective of this experiment is to analyze trace metals present in cigarette tobacco, the cigarette filter, and the ash obtained when the cigarette is burned. Two different brands of cigarettes, one with and one without a filter, were used. The filter was analyzed before and after smoke was drawn through it. The trace metals were extracted using concentrated nitric acid at room temperature and at 100 °C respectively, to test the extraction efficiency. Some tobacco samples were spiked with ZnCl2 and FeCl3 to assess the efficiency of the recovery. Zinc and iron are shown to be present in tobacco, filter, and ash, while chromium was above the detection limit only in the ash. These metals are concentrated in the ash compared to the tobacco by factors of ˜4 (Zn), 12 17 (Fe), and ≥ 2 (Cr). If sufficient laboratory time is available, this experiment could be paired with one using atomic absorption (AA) to demonstrate the advantages and disadvantages of ICP when compared to AA.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorelenkov, Nikolai N

The area of energetic particle (EP) physics of fusion research has been actively and extensively researched in recent decades. The progress achieved in advancing and understanding EP physics has been substantial since the last comprehensive review on this topic by W.W. Heidbrink and G.J. Sadler [1]. That review coincided with the start of deuterium-tritium (DT) experiments on Tokamak Fusion Test reactor (TFTR) and full scale fusion alphas physics studies. Fusion research in recent years has been influenced by EP physics in many ways including the limitations imposed by the "sea" of Alfven eigenmodes (AE) in particular by the toroidicityinduced AEsmore » (TAE) modes and reversed shear Alfven (RSAE). In present paper we attempt a broad review of EP physics progress in tokamaks and spherical tori since the first DT experiments on TFTR and JET (Joint European Torus) including helical/stellarator devices. Introductory discussions on basic ingredients of EP physics, i.e. particle orbits in STs, fundamental diagnostic techniques of EPs and instabilities, wave particle resonances and others are given to help understanding the advanced topics of EP physics. At the end we cover important and interesting physics issues toward the burning plasma experiments such as ITER (International Thermonuclear Experimental Reactor).« less

Development of High-Field ST Merging Experiment: TS-U for High Power Reconnection Heating

NASA Astrophysics Data System (ADS)

Ono, Y.; Koike, H.; Tanabe, H.; Himeno, S.; Ishida, S.; Kimura, K.; Kawanami, M.; Narita, M.; Takahata, Y.; Yokoyama, T.; Inomoto, M.; Cheng, C. Z.

2016-10-01

We are developing high-magnetic field ST merging/ reconnection experiment TS-U with Brec = 0.3-0.5T, based on our scaling law of reconnection heating energy proportional to square of the reconnecting (poloidal) magnetic field Brec. This scaling law indicates that the high-Brec ST merging will heat ions to the burning plasma regime without using any additional heating facility. Its mechanism is that the reconnection outflow accelerates mainly ions up to the poloidal Alfven speed like the Sweet-Parker model. The shock-like density pileups thermalize the accelerated ions in the down-streams in agreement with recent solar satellite observations and PIC simulation results. We already documented significant ion heating of spheromak and ST mergings up to 0.25keV in TS-3 and 1.2keV in MAST, leading us to the high-Brec merging experiment TS-U. It is noted that high-resolution (>500 channel) 2D measurements of ion and electron temperatures is being developed for the purpose of solving all acceleration and heating effects of magnetic reconnection, such as the huge outflow heating of ions in the downstream and electron heating localized at the X-point.

A flammability study of thin plastic film materials

NASA Technical Reports Server (NTRS)

Skinner, S. Ballou

1990-01-01

The Materials Science Laboratory at the Kennedy Space Center presently conducts flammability tests on thin plastic film materials by using a small needle rake method. Flammability data from twenty-two thin plastic film materials were obtained and cross-checked by using three different testing methods: (1) the presently used small needle rake; (2) the newly developed large needle rake; and (3) the previously used frame. In order to better discern the melting-burning phenomenon of thin plastic film material, five additional specific experiments were performed. These experiments determined the following: (1) the heat sink effect of each testing method; (2) the effect of the burn angle on the burn length or melting/shrinkage length; (3) the temperature profile above the ignition source; (4) the melting point and the fire point of each material; and (5) the melting/burning profile of each material via infrared (IR) imaging. The results of these experimentations are presented.

Biomass Burning Airborne and Spaceborne Experiment in the Amazonas (BASE-A)

NASA Technical Reports Server (NTRS)

Kaufman, Y. J.; Setzer, A.; Ward, D.; Tanre, D.; Holben, B. N.; Menzel, P.; Pereira, M. C.; Rasmussen, R.

1992-01-01

Results are presented on measurements of the trace gas and particulate matter emissions due to biomass burning during deforestation and grassland fires in South America, conducted as part of the Biomass Burning Airborne and Spaceborne Experiment in the Amazonas in September 1989. Field observations by an instrumented aircraft were used to estimate concentrations of O3, CO2, CO, CH4, and particulate matter. Fires were observed from satellite imagery, and the smoke optical thickness, particle size, and profiles of the extinction coefficient were measured from the aircraft and from the ground. Four smoke plumes were sampled, three vertical profiles were measured, and extensive ground measurements of smoke optical characteristics were carried out for different smoke types. The simultaneous measurements of the trace gases, smoke particles, and the distribution of fires were used to correlate biomass burning with the elevated levels of ozone.

Disaster planning: the basics of creating a burn mass casualty disaster plan for a burn center.

PubMed

Kearns, Randy D; Conlon, Kathe M; Valenta, Andrea L; Lord, Graydon C; Cairns, Charles B; Holmes, James H; Johnson, Daryhl D; Matherly, Annette F; Sawyer, Dalton; Skarote, Mary Beth; Siler, Sean M; Helminiak, Radm Clare; Cairns, Bruce A

2014-01-01

In 2005, the American Burn Association published burn disaster guidelines. This work recognized that local and state assets are the most important resources in the initial 24- to 48-hour management of a burn disaster. Historical experiences suggest there is ample opportunity to improve local and state preparedness for a major burn disaster. This review will focus on the basics of developing a burn surge disaster plan for a mass casualty event. In the event of a disaster, burn centers must recognize their place in the context of local and state disaster plan activation. Planning for a burn center takes on three forms; institutional/intrafacility, interfacility/intrastate, and interstate/regional. Priorities for a burn disaster plan include: coordination, communication, triage, plan activation (trigger point), surge, and regional capacity. Capacity and capability of the plan should be modeled and exercised to determine limitations and identify breaking points. When there is more than one burn center in a given state or jurisdiction, close coordination and communication between the burn centers are essential for a successful response. Burn surge mass casualty planning at the facility and specialty planning levels, including a state burn surge disaster plan, must have interface points with governmental plans. Local, state, and federal governmental agencies have key roles and responsibilities in a burn mass casualty disaster. This work will include a framework and critical concepts any burn disaster planning effort should consider when developing future plans.

Extra-large negative pressure wound therapy dressings for burns - Initial experience with technique, fluid management, and outcomes.

PubMed

Fischer, Sebastian; Wall, Jennifer; Pomahac, Bohdan; Riviello, Robert; Halvorson, Eric G

2016-03-01

The use of negative-pressure-wound-therapy (NPWT) is associated with improved outcomes in smaller burns. We report our experience using extra-large (XL) NPWT dressings to treat ≥15% total body surface area (TBSA) burned and describe our technique and early outcomes. We also provide NPWT exudate volume for predictive fluid resuscitation in these critically ill patients. We retrospectively reviewed patients treated with XL-NPWT from 2012 to 2014. Following excision/grafting, graft and donor sites were sealed with a layered NPWT dressing. We documented wound size, dressing size, NPWT outputs, graft take, wound infections, and length of stay (LOS). Mean NPWT exudate volume per %TBSA per day was calculated. Twelve burn patients (mean TBSA burned 30%, range 15-60%) were treated with XL-NPWT (dressing TBSA burned and skin graft donor sites range 17-44%). Average graft take was 97%. No wound infections occurred. Two patients had burns ≥50% TBSA and their LOS was reduced compared to ABA averages. XL-NPWT outputs peaked at day 1 after grafting followed by a steady decline until dressings were removed. Average XL-NPWT dressing output during the first 5 days was 101±66mL/%BSA covered per day. 2 patients developed acute kidney injury. The use of XL-NPWT to treat extensive burns is feasible with attention to application technique. NPWT dressings appear to improve graft take, and to decrease risk of infection, LOS, and pain and anxiety associated with wound care. Measured fluid losses can improve patient care in future applications of NPWT to large burn wounds. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

The Parkland Burn Center experience with 297 cases of child abuse from 1974 to 2010.

PubMed

Hodgman, Erica I; Pastorek, Rachel A; Saeman, Melody R; Cripps, Michael W; Bernstein, Ira H; Wolf, Steven E; Kowalske, Karen J; Arnoldo, Brett D; Phelan, Herb A

2016-08-01

Pediatric burns due to abuse are unfortunately relatively common, accounting for 5.8-8.8% of all cases of abuse annually. Our goal was to evaluate our 36-year experience in the evaluation and management of the victims of abuse in the North Texas area. A prospectively maintained database containing records on all admissions from 1974 through 2010 was queried for all patients aged less than 18 years. Patients admitted for management of a non-burn injury were excluded from the analysis. Of 5,553 pediatric burn admissions, 297 (5.3%) were due to abuse. Children with non-accidental injuries tended to be younger (2.1 vs. 5.0 years, p<0.0001) and male (66.0 vs. 56.5%, p=0.0008). Scald was the most common mechanism of injury overall (44.8%), and was also the predominant cause of inflicted burns (89.6 vs. 42.3%, p<0.0001). Multivariate logistic regression identified age, gender, presence of a scald, contact, or chemical burn, and injury to the hands, bilateral feet, buttocks, back, and perineum to be significant predictors of abuse. Victims of abuse were also found to have worse outcomes, including mortality (5.4 vs. 2.3%, p=0.0005). After adjusting for age, mechanism of injury, and burn size, abuse remained a significant predictor of mortality (OR 3.3, 95% CI 1.5-7.2) CONCLUSIONS: Clinicians should approach all burn injuries in young children with a high index of suspicion, but in particular those with scalds, or injuries to the buttocks, perineum, or bilateral feet should provoke suspicion. Burns due to abuse are associated with worse outcomes, including length of stay and mortality. Copyright © 2016. Published by Elsevier Ltd.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-05

ISS035-E-014971 (6 April 2013) --- This is a close-up image photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-09

ISS035-E-015900 (10 April 2013) --- This is one of a series of close-up images photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted several runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-09

ISS035-E-015679 (10 April 2013) --- This is one of a series of close-up images photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted a series of runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS-II Experiment

NASA Image and Video Library

2014-07-23

ISS040-E-073120 (23 July 2014) --- This is a close-up image photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Reid Wiseman (out of frame), Expedition 40 flight engineer, conducted runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-05

ISS035-E-014987 (6 April 2013) --- This is a close-up image photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-09

ISS035-E-015827 (10 April 2013) --- This is one of a series of close-up images photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted a series of runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-09

ISS035-E-015930 (10 April 2013) --- This is one of a series of close-up images photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Chris Cassidy (out of frame) conducted several runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

BASS-II Experiment

NASA Image and Video Library

2014-06-27

ISS040-E-023287 (27 June 2014) --- This is a close-up image photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, NASA astronaut Reid Wiseman (out of frame), Expedition 40 flight engineer, conducted runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

Slowing light down by low magnetic fields: pulse delay by transient spectral hole-burning in ruby.

PubMed

Riesen, Hans; Rebane, Aleksander K; Szabo, Alex; Carceller, Ivana

2012-08-13

We report on the observation of slow light induced by transient spectral hole-burning in a solid, that is based on excited-state population storage. Experiments were conducted in the R1-line (2E←4A2 transition) of a 2.3 mm thick pink ruby (Al2O3:Cr(III) 130 ppm). Importantly, the pulse delay can be controlled by the application of a low external magnetic field B||c≤9 mT and delays of up to 11 ns with minimal pulse distortion are observed for ~55 ns Gaussian pulses. The delay corresponds to a group velocity value of ~c/1400. The experiment is very well modelled by linear spectral filter theory and the results indicate the possibility of using transient hole-burning based slow light experiments as a spectroscopic technique.

In vitro bactericidal efficacy of atmospheric-pressure plasma jet on titanium-based implant infected with Staphylococcus aureus

NASA Astrophysics Data System (ADS)

Park, Young-Ouk; Lee, Chang-Min; Kim, Myung-Sun; Jung, Sang-Chul; Yang, Seong-Won; Kook, Min-Suk; Kim, Byung-Hoon

2017-01-01

Staphylococcus aureus is a representative of gram-positive bacteria that causes skin infection, respiratory diseases, and burned tissue infections. The aim of this study was to evaluate the sterilizing efficiency of an atmospheric-pressure plasma jet (APPJ) on S. aureus adhered on a titanium surface. During the APPJ sterilization, the plasma gases used were Ar, Ar+N2, and Ar+O2. With increasing APPJ treatment time, the viability of S. aureus decreased. The addition of O2 gas to Ar gas resulted in a higher sterilizing efficiency than the addition of other groups. Plasma exposure induced bacterial oxidative stress, and it was confirmed that the cell membrane was seriously damaged by the production of reactive oxygen species. Our finding suggests that the APPJ is an effective tool for clinical antimicrobial therapy.

Multi-energy SXR cameras for magnetically confined fusion plasmas (invited).

PubMed

Delgado-Aparicio, L F; Maddox, J; Pablant, N; Hill, K; Bitter, M; Rice, J E; Granetz, R; Hubbard, A; Irby, J; Greenwald, M; Marmar, E; Tritz, K; Stutman, D; Stratton, B; Efthimion, P

2016-11-01

A compact multi-energy soft x-ray camera has been developed for time, energy and space-resolved measurements of the soft-x-ray emissivity in magnetically confined fusion plasmas. Multi-energy soft x-ray imaging provides a unique opportunity for measuring, simultaneously, a variety of important plasma properties (T e , n Z , ΔZ eff , and n e,fast ). The electron temperature can be obtained by modeling the slope of the continuum radiation from ratios of the available brightness and inverted radial emissivity profiles over multiple energy ranges. Impurity density measurements are also possible using the line-emission from medium- to high-Z impurities to separate the background as well as transient levels of metal contributions. This technique should be explored also as a burning plasma diagnostic in-view of its simplicity and robustness.

Spectral broadening of characteristic γ-ray emission peaks from 12C(3He,pγ)14N reactions in fusion plasmas.

PubMed

Tardocchi, M; Nocente, M; Proverbio, I; Kiptily, V G; Blanchard, P; Conroy, S; Fontanesi, M; Grosso, G; Kneupner, K; Lerche, E; Murari, A; Cippo, E Perelli; Pietropaolo, A; Syme, B; Van Eester, D; Gorini, G

2011-11-11

The spectral broadening of characteristic γ-ray emission peaks from the reaction (12)C((3)He,pγ)(14)N was measured in D((3)He) plasmas of the JET tokamak with ion cyclotron resonance heating tuned to the fundamental harmonic of (3)He. Intensities and detailed spectral shapes of γ-ray emission peaks were successfully reproduced using a physics model combining the kinetics of the reacting ions with a detailed description of the nuclear reaction differential cross sections for populating the L1-L8 (14)N excitation levels yielding the observed γ-ray emission. The results provide a paradigm, which leverages knowledge from areas of physics outside traditional plasma physics, for the development of nuclear radiation based methods for understanding and controlling fusion burning plasmas.

Measurement of Solid Rocket Propellant Burning Rate Using X-ray Imaging

NASA Astrophysics Data System (ADS)

Denny, Matthew D.

The burning rate of solid propellants can be difficult to measure for unusual burning surface geometries, but X-ray imaging can be used to measure burning rate. The objectives of this work were to measure the baseline burning rate of an electrically-controlled solid propellant (ESP) formulation with real-time X-ray radiography and to determine the uncertainty of the measurements. Two edge detection algorithms were written to track the burning surface in X-ray videos. The edge detection algorithms were informed by intensity profiles of simulated 2-D X-ray images. With a 95% confidence level, the burning rates measured by the Projected-Slope Intersection algorithm in the two combustion experiments conducted were 0.0839 in/s +/-2.86% at an average pressure of 407 psi +/-3.6% and 0.0882 in/s +/-3.04% at 410 psi +/-3.9%. The uncertainty percentages were based on the statistics of a Monte Carlo analysis on burning rate.

From W7-X to a HELIAS fusion power plant: motivation and options for an intermediate-step burning-plasma stellarator

NASA Astrophysics Data System (ADS)

Warmer, F.; Beidler, C. D.; Dinklage, A.; Wolf, R.; The W7-X Team

2016-07-01

As a starting point for a more in-depth discussion of a research strategy leading from Wendelstein 7-X to a HELIAS power plant, the respective steps in physics and engineering are considered from different vantage points. The first approach discusses the direct extrapolation of selected physics and engineering parameters. This is followed by an examination of advancing the understanding of stellarator optimisation. Finally, combining a dimensionless parameter approach with an empirical energy confinement time scaling, the necessary development steps are highlighted. From this analysis it is concluded that an intermediate-step burning-plasma stellarator is the most prudent approach to bridge the gap between W7-X and a HELIAS power plant. Using a systems code approach in combination with transport simulations, a range of possible conceptual designs is analysed. This range is exemplified by two bounding cases, a fast-track, cost-efficient device with low magnetic field and without a blanket and a device similar to a demonstration power plant with blanket and net electricity power production.

The neutron imaging diagnostic at NIF (invited).

PubMed

Merrill, F E; Bower, D; Buckles, R; Clark, D D; Danly, C R; Drury, O B; Dzenitis, J M; Fatherley, V E; Fittinghoff, D N; Gallegos, R; Grim, G P; Guler, N; Loomis, E N; Lutz, S; Malone, R M; Martinson, D D; Mares, D; Morley, D J; Morgan, G L; Oertel, J A; Tregillis, I L; Volegov, P L; Weiss, P B; Wilde, C H; Wilson, D C

2012-10-01

A neutron imaging diagnostic has recently been commissioned at the National Ignition Facility (NIF). This new system is an important diagnostic tool for inertial fusion studies at the NIF for measuring the size and shape of the burning DT plasma during the ignition stage of Inertial Confinement Fusion (ICF) implosions. The imaging technique utilizes a pinhole neutron aperture, placed between the neutron source and a neutron detector. The detection system measures the two dimensional distribution of neutrons passing through the pinhole. This diagnostic has been designed to collect two images at two times. The long flight path for this diagnostic, 28 m, results in a chromatic separation of the neutrons, allowing the independently timed images to measure the source distribution for two neutron energies. Typically the first image measures the distribution of the 14 MeV neutrons and the second image of the 6-12 MeV neutrons. The combination of these two images has provided data on the size and shape of the burning plasma within the compressed capsule, as well as a measure of the quantity and spatial distribution of the cold fuel surrounding this core.

Plasma viscosity with mass transport in spherical inertial confinement fusion implosion simulations

DOE PAGES

Vold, Erik Lehman; Joglekar, Archis S.; Ortega, Mario I.; ...

2015-11-20

The effects of viscosity and small-scale atomic-level mixing on plasmas in inertial confinement fusion(ICF) currently represent challenges in ICF research. Many current ICF hydrodynamic codes ignore the effects of viscosity though recent research indicates viscosity and mixing by classical transport processes may have a substantial impact on implosion dynamics. In this paper, we have implemented a Lagrangian hydrodynamic code in one-dimensional spherical geometry with plasmaviscosity and mass transport and including a three temperature model for ions, electrons, and radiation treated in a gray radiation diffusion approximation. The code is used to study ICF implosion differences with and without plasmaviscosity andmore » to determine the impacts of viscosity on temperature histories and neutron yield. It was found that plasmaviscosity has substantial impacts on ICF shock dynamics characterized by shock burn timing, maximum burn temperatures, convergence ratio, and time history of neutron production rates. Finally, plasmaviscosity reduces the need for artificial viscosity to maintain numerical stability in the Lagrangian formulation and also modifies the flux-limiting needed for electron thermal conduction.« less

Gerst in U.S. Laboratory

NASA Image and Video Library

2014-06-17

ISS040-E-012309 (16 June 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, conducts two flame tests for a combustion experiment known as the Burning and Suppression of Solids (BASS) in the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft.

Discussion of a ``coherent artifact'' in four-wave mixing experiments

NASA Astrophysics Data System (ADS)

Ferwerda, Hedzer A.; Terpstra, Jacob; Wiersma, Douwe A.

1989-09-01

In this paper, we discuss the nonlinear optical effects that arise when stochastic light waves, with different correlation times, interfere in an absorbing medium. It is shown that four-wave mixing signals are generated in several directions that spectrally track the incoming light fields. This effect is particularly relevant to transient hole-burning experiments, where one of these signals could easily be misinterpreted as a genuine hole-burning feature.

Burning Heptane Droplets on STS-94

NASA Technical Reports Server (NTRS)

2003-01-01

Fuel ignites and burns in the Droplet Combustion Experiment (DCE) on STS-94 on July 11, 1997. This round of experiments burned heptane droplets in 1/2 atmosphere pressure consisting of oxygen and helium. During this mission, scientists have seen for the first time droplets which stop burning due to heat loss by radiation. From these data, the investigators hope to understand the physical and chemical processes that take place in droplet combustion in different environments, including conditions under which the flames extinguish, the chemistry of the combustion reaction, and the production of pollutants such as nitrogen oxides and soot particles. The DCE was designed to investigate the fundamental combustion aspects of single, isolated droplets under different pressures and ambient oxygen concentrations for a range of droplet sizes varying between 2 and 5 mm. The DCE principal investigator was Forman Williams, University of California, San Diego. The experiment was part of the space research investigations conducted during the Microgravity Science Laboratory-1R mission (STS-94, July 1-17 1997). Advanced combustion experiments will be a part of investigations plarned for the International Space Station.(983KB, 9-second MPEG, screen 320 x 240 pixels; downlinked video, higher quality not available) A still JPG composite of this movie is available at http://mix.msfc.nasa.gov/ABSTRACTS/MSFC-0300172.html.

Particulate pollutants in the Brazilian city of São Paulo: 1-year investigation for the chemical composition and source apportionment

NASA Astrophysics Data System (ADS)

Martins Pereira, Guilherme; Teinilä, Kimmo; Custódio, Danilo; Gomes Santos, Aldenor; Xian, Huang; Hillamo, Risto; Alves, Célia A.; Bittencourt de Andrade, Jailson; Olímpio da Rocha, Gisele; Kumar, Prashant; Balasubramanian, Rajasekhar; de Fátima Andrade, Maria; de Castro Vasconcellos, Pérola

2017-10-01

São Paulo in Brazil has relatively relaxed regulations for ambient air pollution standards and often experiences high air pollution levels due to emissions of particulate pollutants from local sources and long-range transport of air masses impacted by biomass burning. In order to evaluate the sources of particulate air pollution and related health risks, a year-round sampling was done at the University of São Paulo campus (20 m a.g.l.), a green area near an important expressway. The sampling was performed for PM2. 5 ( ≤ 2. 5 µm) and PM10 ( ≤ 10 µm) in 2014 through intensive (everyday sampling in wintertime) and extensive campaigns (once a week for the whole year) with 24 h of sampling. This year was characterized by having lower average precipitation compared to meteorological data, and high-pollution episodes were observed all year round, with a significant increase in pollution level in the intensive campaign, which was performed during wintertime. Different chemical constituents, such as carbonaceous species, polycyclic aromatic hydrocarbons (PAHs) and derivatives, water-soluble ions, and biomass burning tracers were identified in order to evaluate health risks and to apportion sources. The species such as PAHs, inorganic and organic ions, and monosaccharides were determined using chromatographic techniques and carbonaceous species using thermal-optical analysis. Trace elements were determined using inductively coupled plasma mass spectrometry. The risks associated with particulate matter exposure based on PAH concentrations were also assessed, along with indexes such as the benzo[a]pyrene equivalent (BaPE) and lung cancer risk (LCR). High BaPE and LCR were observed in most of the samples, rising to critical values in the wintertime. Also, biomass burning tracers and PAHs were higher in this season, while secondarily formed ions presented low variation throughout the year. Meanwhile, vehicular tracer species were also higher in the intensive campaign, suggesting the influence of lower dispersion conditions in that period. Source apportionment was performed using positive matrix factorization (PMF), which indicated five different factors: road dust, industrial emissions, vehicular exhaust, biomass burning and secondary processes. The results highlighted the contribution of vehicular emissions and the significant input from biomass combustion in wintertime, suggesting that most of the particulate matter is due to local sources, in addition to the influence of pre-harvest sugarcane burning.

Survival and growth of seed trees 20 years after a natural regeneration cut in the piedmont of Georgia

Treesearch

Stephen R. Logan; M. Boyd Edwards; Barry D. Shiver

2005-01-01

An experiment was installed in 1982 to compare six methods of natural regeneration in the Piedmont of Georgia. These methods include (1) clearcut with seed in place; (2) clearcut with seed in place and preharvest burn; (3) seed tree; (4) seed tree with preharvest burn; (5) shelterwood; and (6) shelterwood with preharvest burn. Because of endangered species regulations...

Emissions of volatile organic compounds and particulate matter from small-scale peat fires

NASA Astrophysics Data System (ADS)

George, I. J.; Black, R.; Walker, J. T.; Hays, M. D.; Tabor, D.; Gullett, B.

2013-12-01

Air pollution emitted from peat fires can negatively impact regional air quality, visibility, climate, and human health. Peat fires can smolder over long periods of time and, therefore, can release significantly greater amounts of carbon into the atmosphere per unit area compared to burning of other types of biomass. However, few studies have characterized the gas and particulate emissions from peat burning. To assess the atmospheric impact of peat fires, particulate matter (PM) and volatile organic compounds (VOCs) were quantified from controlled small-scale peat fire experiments. Major carbon emissions (i.e. CO2, CO, methane and total hydrocarbons) were measured during the peat burn experiments. Speciated PM mass was also determined from the peat burns from filter and polyurethane foam samples. Whole air samples were taken in SUMMA canisters and analyzed by gas chromatography-mass spectrometry to measure 82 trace VOCs. Additional gaseous carbonyl species were measured by sampling with dinitrophenylhydrazine-coated cartridges and analyzed with high performance liquid chromatography. VOCs with highest observed concentrations measured from the peat burns were propylene, benzene, chloromethane and toluene. Gas-phase carbonyls with highest observed concentrations included acetaldehyde, formaldehyde and acetone. Emission factors of major pollutants will be compared with recommended values for peat and other biomass burning.

Burn Injury and Explosions: An Australian Perspective

PubMed Central

Greenwood, John E.

2009-01-01

Objectives: Increasingly (but not exclusively), terrorist activity and the use of explosive devices have enjoyed the focus of the global media. This paper aims to bring a range of issues to attention, to highlight how burn injuries are sustained in such incidents and why burn injuries (and thus burn disasters) are so complicated to manage. Materials and Methods: The author's experience with burn injury caused during explosions and his involvement in burn disaster situations has been summarized to form the basis of the article. This has been expanded upon with discussion points which provide a strategy for planning for such events and by a broad sample of the literature. Results: Several strategies are suggested to facilitate planning for burn disasters and to illustrate to those not directly involved why forward planning is pivotal to success when these incidents occur. Conclusions: Disasters generating large numbers of burn-injured are relatively frequent. Explosive devices are widespread in their use both in military and increasingly in civilian fields. Encompassing a large range of aetiologies, geographical sites, populations, and resources; burn disaster management is difficult and planning essential. PMID:19834533

Assessment of burn-specific health-related quality of life and patient scar status following burn.

PubMed

Oh, Hyunjin; Boo, Sunjoo

2017-11-01

This study assessed patient-perceived levels of scar assessment and burn-specific quality of life (QOL) in Korean burn patients admitted to burn care centers and identified differences in scar assessment and QOL based on various patient characteristics. A cross-sectional descriptive study using anonymous paper-based survey methods was conducted with 100 burn patients from three burn centers specializing in burn care in South Korea. Mean subject age was 44.5 years old, and 69% of the subjects were men. The overall mean QOL was 2.91 out of 5. QOL was lowest for the work subdomain (2.25±1.45) followed by the treatment regimen subdomain (2.32±1.16). The subjects' mean total scar assessment score was 35.51 out of 60, and subjects were most unsatisfied with scar color. Subjects with low income, flame-source burns, severe burns, visible scars, and scars on face or hand reported significantly lower QOL. Subjects with severe burn degree and burn range perceived their burn scar condition to be worse than that of others. The results show that burn subjects experience the most difficulties with their work and the treatment regimen. Subjects with severe burn and visible scarring have a reduced QOL and a poor scar status. Scar management intervention may improve QOL of burn patients especially those with severe burn and visible scars. Further studies are warranted to evaluate the relationship between scar assessment and QOL. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Burns in South Korea: An analysis of nationwide data from the Health Insurance Review and Assessment Service.

PubMed

Oh, Hyunjin; Boo, Sunjoo

2016-05-01

The purpose of the study was to identify and describe the incidence of burn injuries in patients seen and treated in South Korea. Characteristics of inpatients and outpatients with burns were analyzed according to gender, age, burn site, and burn severity. This retrospective study examined the characteristics of a stratified sample of burn patients seen and treated in South Korea during the calendar year 2011. The sample was drawn from the national patient database Health Insurance Review and Assessment (HIRA). Approximately 1.71% of the total patients in the Patient Sample of HIRA for 2011 were burn-injured patients. The numbers of patients treated for burns were 913/10(5) males (n=8009) and 1454/10(5) females (n=11,881). Nearly all of these patients (94.1%) were covered by national health insurance and the majority of these patients (80.6%) were treated as outpatients. Nearly half of the burn injuries were of the upper extremities (43.5%), and most of these injuries (71.5%) were rated as second-degree burns. A review of the national data on patients seen and treated for burns in 2011 revealed that people in South Korea may experience higher numbers and more severe cases of burns and burn-related injuries than found in other countries. General burn prevention programs as well as gender- and age-specific prevention strategies are needed to reduce the risk of burns in this population. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Epidemiology and outcome of burns at the Saud Al Babtain Burns, Plastic Surgery and Reconstructive Center, Kuwait: our experience over five years (from 2006 to 2010)

PubMed Central

Khashaba, H.A.; Al-Fadhli, A.N.; Al-Tarrah, K.S.; Wilson, Y.T.; Moiemen, N.

2012-01-01

Summary Aim To determine the epidemiology and clinical presentation, and any contributing factors responsible for burns and outcome of care in Kuwait over the 5-yr period January 2006 to December 2010. Patients and methods. The study reviewed 1702 burn patients admitted over the study period to the Saud Al Babtain Burns, Plastic and Reconstructive Surgery Center, Kuwait. Patient characteristics, including age, sex, type of burn, nationality, total body surface area (TBSA) burn, hospital stay in days, and mortality were recorded. Results. Seventy-one per cent of the 1702 burn patients admitted were males; 540 were children. The majority of patients (64%) had less than 15% TBSA burns and only 14% had more than 50% TBSA burns. Flame burns were the most common cause of burn injuries (60%), followed by scalds (29%). Scalds were most common in children. The mortality rate was 5.75%. Flame burn was the leading cause of mortality. Lethal dose 50 (% TBSA at which a certain group has a 50% chance of survival) for adults (16-40 yr) and for the elderly (>65 yr) was 76.5% and 41.8% TBSA respectively. Conclusion. Burn injury is an important public health concern and is associated with high morbidity and mortality. Flame and scald burns are commonly a result of domestic and occupational accidents and they are preventable. Effective initial resuscitation, infection control, and adequate surgical treatment improve outcomes. PMID:23766750

Initial experience with a composite autologous skin substitute.

PubMed

Sheridan, R L; Morgan, J R; Cusick, J L; Petras, L M; Lydon, M M; Tompkins, R G

2001-08-01

Patients with large burns are surviving in increasing numbers, but there remains no durable and reliable permanent skin replacement. After initial favorable small animal experiments, a pilot trial of a composite skin replacement was performed in patients with massive burns. A composite skin replacement (CSR) was developed by culturing autologous keratinocytes on acellular allogenic dermis. This material was engrafted in patients with massive burns and compared to a matched wound covered with split thickness autograft. With human studies committee approval, 12 wounds in 7 patients were grafted with CSR while a matched control wound was covered with split thickness autograft. These 7 children had an average age of 6.4+/-1.4 yr and burn size of 75.9+/-5.0% of the body surface. Nine wounds were acute burns and three were reconstructive releases. Successful vascularization at 14 days averaged 45.7+/-14.2% (range 0-100%) in the study wounds and 98+/-1% (range 90-100%) in the control sites (P<0.05). Reduced CSR take seemed to correlate with wound colonization. All children survived. While CSR did not engraft with the reliability of standard autograft, this pilot experience is encouraging in that successful wound closure with this material is possible, if not yet dependable. It is hoped that a more mature epidermal layer may facilitate engraftment, and trials to explore this possibility are in progress.

Fluorine-fixing efficiency on calcium-based briquette: pilot experiment, demonstration and promotion.

PubMed

Yang, Jiao-lan; Chen, Dong-qing; Li, Shu-min; Yue, Yin-ling; Jin, Xin; Zhao, Bing-cheng; Ying, Bo

2010-02-05

The fluorosis derived from coal burning is a very serious problem in China. By using fluorine-fixing technology during coal burning we are able to reduce the release of fluorides in coal at the source in order to reduce pollution to the surrounding environment by coal burning pollutants as well as decrease the intake and accumulating amounts of fluorine in the human body. The aim of this study was to conduct a pilot experiment on calcium-based fluorine-fixing material efficiency during coal burning to demonstrate and promote the technology based on laboratory research. A proper amount of calcium-based fluorine sorbent was added into high-fluorine coal to form briquettes so that the fluorine in high-fluorine coal can be fixed in coal slag and its release into atmosphere reduced. We determined figures on various components in briquettes and fluorine in coal slag as well as the concentrations of indoor air pollutants, including fluoride, sulfur dioxide and respirable particulate matter (RPM), and evaluated the fluorine-fixing efficiency of calcium-based fluorine sorbents and the levels of indoor air pollutants. Pilot experiments on fluorine-fixing efficiency during coal burning as well as its demonstration and promotion were carried out separately in Guiding and Longli Counties of Guizhou Province, two areas with coal burning fluorosis problems. If the calcium-based fluorine sorbent mixed coal was made into honeycomb briquettes the average fluorine-fixing ratio in the pilot experiment was 71.8%. If the burning calcium-based fluorine-fixing bitumite was made into a coalball, the average of fluorine-fixing ratio was 77.3%. The concentration of fluoride, sulfur dioxide and PM10 of indoor air were decreased significantly. There was a 10% increase in the cost of briquettes due to the addition of calcium-based fluorine sorbent. The preparation process of calcium-based fluorine-fixing briquette is simple yet highly flammable and it is applicable to regions with abundant bitumite coal. As a small scale application, villagers may make fluorine-fixing coalballs or briquettes by themselves, achieving the optimum fluorine-fixing efficiency and reducing indoor air pollutants providing environmental and social benefits.

PTCR characteristics and microstructure of porous (Ba,Sr)TiO3 ceramics prepared by spark plasma sintering

NASA Astrophysics Data System (ADS)

Lee, Ki-Ju; Tang, Dongxu; Park, K.; Cho, Won-Seung

2010-02-01

Porous Y-doped (Ba,Sr)TiO3 ceramics were prepared by the spark plasma sintering of (Ba,Sr)TiO3 powders with different amounts of carbon black, and by subsequently burning out the carbon black acting as a pore precursor. The microstructure, PTCR and gas-sensing characteristics for porous Y-doped (Ba,Sr)TiO3 ceramics were investigated. Spark plasma sintered (Ba,Sr)TiO3 ceramics revealed a very fine microstructure containing submicron-sized grains with a cubic phase and revealed an increased porosity after the carbon black was burned out. As a result of reoxidation treatment, the grain size of the (Ba,Sr)TiO3 ceramics increased to a few μm and the cubic phase transformed into a tetragonal phase. The phase transformation of (Ba,Sr)TiO3 ceramics was affected by grain size. The PTCR jump in the (Ba,Sr)TiO3 ceramics prepared by adding 40 vol.% carbon black showed an excellent value of 4.72 × 106, which was ten times higher than the PTCR jump in (Ba,Sr)TiO3 ceramics. The electrical resistivity of the porous (Ba,Sr)TiO3 ceramics was recovered as the atmosphere changed from a reducing gas (N2) to an oxidizing gas (O2) under consecutive heating and cooling cycles.

From pure fusion to fusion-fission Demo tokamaks

NASA Astrophysics Data System (ADS)

Mirnov, S. V.

2013-04-01

The major requirements for pure fusion tokamak reactors and tokamak-based fusion neutron sources (FNS) are analyzed together with possible paths from the present-day tokamak towards the FNS tokamak. The FNS are of interest for traditional fission reactors as a method of waste management by burning of long-lived transuranic radionuclides (minorities) and fission fuel breeding. The Russian fission community places several hard requirements on the quality of FNS suitable for the first step of the investigation program of minority burning and breeding. They are (a) a steady-state regime of neutron production (more than 80% of the operational time), (b) a neutron power flux density greater than >0.2 MW m-2, (c) a total surface integrated neutron power >10 MW. Among the different FNS projects, based on magnetically confined plasmas, only ‘classical tokamak’ is most likely to fulfill these requirements in the nearest future. Some of the most important improvements of the ‘classical tokamak’ needed for successful realization of the FNS are (1) decrease in Zeff (probably, by making use of lithium as a part of plasma-facing components), (2) He removal and closed loop DT fuel circulation, (3) increase in the energy of stationary injected neutral tritium beams up to 150-170 keV and (4) control of impurity contamination at the plasma center (probably, by local RF heating). These key issues are discussed.

Advanced Fuel Cycles for Fusion Reactors: Passive Safety and Zero-Waste Options

NASA Astrophysics Data System (ADS)

Zucchetti, Massimo; Sugiyama, Linda E.

2006-05-01

Nuclear fusion is seen as a much ''cleaner'' energy source than fission. Most of the studies and experiments on nuclear fusion are currently devoted to the Deuterium-Tritium (DT) fuel cycle, since it is the easiest way to reach ignition. The recent stress on safety by the world's community has stimulated the research on other fuel cycles than the DT one, based on 'advanced' reactions, such as the Deuterium-Helium-3 (DHe) one. These reactions pose problems, such as the availability of 3He and the attainment of the higher plasma parameters that are required for burning. However, they have many advantages, like for instance the very low neutron activation, while it is unnecessary to breed and fuel tritium. The extrapolation of Ignitor technologies towards a larger and more powerful experiment using advanced fuel cycles (Candor) has been studied. Results show that Candor does reach the passive safety and zero-waste option. A fusion power reactor based on the DHe cycle could be the ultimate response to the environmental requirements for future nuclear power plants.

The TIL commissioning and performance

NASA Astrophysics Data System (ADS)

Zhang, X.; Zheng, W.; Wei, X.; Jing, F.; Sui, Z.; Zheng, K.; Xu, Q.; Yuan, X.; Jiang, X.; Yang, L.; Ma, P.; Li, M.; Wang, J.; Hu, D.; He, S.; Li, F.; Peng, Z.; Feng, B.; Zhou, H.; Guo, L.; Li, X.; Zhang, X.; Su, J.; Zhu, Q.; Yu, H.; Zhao, R.; Ma, C.; He, H.; Fan, D.; Zhang, W.

2008-05-01

The TIL serves for both technological platforms for SG-III construction and physical experiments to study and understand target physics toward ignition and plasma burning [2]. The TIL has been designed to produce 10kJ blue light. Its eight-beam are stacked 4 high by 2 wide, The clear optical aperture is 30cm×30cm The cavity and booster amplifiers have 9 and 6 glass slabs respectively, with thickness of 3.8cm. The cavity is a four-pass amplification stage with the seed pulse injected through its cavity spatial filter, while the booster a single pass amplification stage. The commissioning experiments have successfully been conducted to test the output and control abilities of the system. A single beam line of TIL produced 3-ns pulse of 1645 Joule blue light at the target, which demonstrated that the TIL can deliver ten-thousand-joule blue light to the target. Beam qualities have been investigated jointly with the laser chain simulations using the SG-99 code. The wavefront distortions of the beams will be improved by deformable mirrors.

Cassidy conducts BASS Experiment Test Operations

NASA Image and Video Library

2013-04-05

ISS035-E-015081 (5 April 2013) --- Astronaut Chris Cassidy, Expedition 35 flight engineer, conducts a session of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, Cassidy conducted a run of the experiment, which examined the burning and extinction characteristics of a wide variety of fuel samples in microgravity and will guide strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

A Novel Approach for High Deposition Rate Cladding with Minimal Dilution with an Arc - Laser Process Combination

NASA Astrophysics Data System (ADS)

Barroi, A.; Hermsdorf, J.; Prank, U.; Kaierle, S.

First results of the process development of a novel approach for a high deposition rate cladding process with minimal dilution are presented. The approach will combine the enormous melting potential of an electrical arc that burns between two consumable wire electrodes with the precision of a laser process. Separate test for the plasma melting and for the laser based surface heating have been performed. A steadily burning arc between the electrodes could be established and a deposition rate of 10 kg/h could be achieved. The laser was able to apply the desired heat profile, needed for the combination of the processes. Process problems were analyzed and solutions proposed.

Effects of large-angle Coulomb collisions on inertial confinement fusion plasmas.

PubMed

Turrell, A E; Sherlock, M; Rose, S J

2014-06-20

Large-angle Coulomb collisions affect the rates of energy and momentum exchange in a plasma, and it is expected that their effects will be important in many plasmas of current research interest, including in inertial confinement fusion. Their inclusion is a long-standing problem, and the first fully self-consistent method for calculating their effects is presented. This method is applied to "burn" in the hot fuel in inertial confinement fusion capsules and finds that the yield increases due to an increase in the rate of temperature equilibration between electrons and ions which is not predicted by small-angle collision theories. The equilibration rate increases are 50%-100% for number densities of 10(30)  m(-3) and temperatures around 1 keV.

Comparison of oxidative stress & leukocyte activation in patients with severe sepsis & burn injury

PubMed Central

Mühl, Diana; Woth, Gábor; Drenkovics, Livia; Varga, Adrienn; Ghosh, Subhamay; Csontos, Csaba; Bogár, Lajos; Wéber, György; Lantos, János

2011-01-01

Background & objectives: We evaluated pro- and anti-oxidant disturbances in sepsis and non-sepsis burn patients with systemic inflammatory response syndrome (SIRS). Adhesion molecules and inflammation markers on leukocytes were also analyzed. We hypothesized that oxidative stress and leukocyte activation markers can lead to the severity of sepsis. Methods: In 28 severe sepsis and 27 acute burn injury patients blood samples were collected at admission and 4 days consecutively. Oxidative stress markers: production of reactive oxygen species (ROS), myeloperoxidase, malondialdehyde and endogenous antioxidants: plasma protein sulphydryl groups, reduced glutathione, superoxide dismutase and catalase were measured. Flow cytometry was used to determine CD11a, CD14, CD18, CD49d and CD97 adhesion molecules on leukocytes. Procalcitonin, C-reactive protein, fibrinogen, platelet count and lactate were also analyzed. Results: Pro-oxidant parameters were significantly elevated in sepsis patients at admission, ROS intensity increased in burn patients until the 5th day. Endogenous antioxidant levels except catalase showed increased levels after burn trauma compared to sepsis. Elevated granulocyte activation and suppressed lymphocyte function were found at admission and early activation of granulocytes caused by increasing activation/migration markers in sepsis. Leukocyte adhesion molecule expression confirmed the suppressed lymphocyte and monocyte function in sepsis. Interpretation & conclusions: Severe sepsis is accompanied by oxidative stress and pathological leukocyte endothelial cell interactions. The laboratory parameters used for the evaluation of sepsis and several markers of pro- and antioxidant status were different between sepsis and non-sepsis burn patients. The tendency of changes in these parameters may refer to major oxidative stress in sepsis and developing SIRS in burns. PMID:21808137

Fusarium spp infections in a pediatric burn unit: nine years of experience.

PubMed

Rosanova, María Teresa; Brizuela, Martín; Villasboas, Mabel; Guarracino, Fabian; Alvarez, Veronica; Santos, Patricia; Finquelievich, Jorge

2016-01-01

Fusarium spp are ubiquitous fungi recognized as opportunistic agents of human infections, and can produce severe infections in burn patients. The literature on Fusarium spp infections in pediatric burn patients is scarce. To describe the clinical and epidemiological features as well as outcome of Fusarium spp infections in pediatric burn patients. Retrospective, descriptive study of Fusarium spp infections in a specialized intensive care burn unit. In 15 patients Fusarium spp infections were diagnosed. Median age was 48 months. Direct fire injury was observed in ten patients. The median affected burn surface area was 45%. Twelve patients had a full thickness burn. Fourteen patients had a Garces Index ≥3. Fungal infection developed at a median of 11 days after burn injury. Fungi were isolated from burn wound in 14 patients and from the bone in one patient. Amphotericin B was the drug of choice for treatment followed by voriconazole. Median time of treatment completion was 23 days. One patient (7%) died of fungal infection-related causes. In our series Fusarium spp was an uncommon pathogen in severely burnt patients. The burn wound was the most common site of infection and mortality was low. Copyright © 2016 Elsevier Editora Ltda. All rights reserved.

Modeling crop residue burning experiments to evaluate smoke emissions and plume transport.

PubMed

Zhou, Luxi; Baker, Kirk R; Napelenok, Sergey L; Pouliot, George; Elleman, Robert; O'Neill, Susan M; Urbanski, Shawn P; Wong, David C

2018-06-15

Crop residue burning is a common land management practice that results in emissions of a variety of pollutants with negative health impacts. Modeling systems are used to estimate air quality impacts of crop residue burning to support retrospective regulatory assessments and also for forecasting purposes. Ground and airborne measurements from a recent field experiment in the Pacific Northwest focused on cropland residue burning was used to evaluate model performance in capturing surface and aloft impacts from the burning events. The Community Multiscale Air Quality (CMAQ) model was used to simulate multiple crop residue burns with 2 km grid spacing using field-specific information and also more general assumptions traditionally used to support National Emission Inventory based assessments. Field study specific information, which includes area burned, fuel consumption, and combustion completeness, resulted in increased biomass consumption by 123 tons (60% increase) on average compared to consumption estimated with default methods in the National Emission Inventory (NEI) process. Buoyancy heat flux, a key parameter for model predicted fire plume rise, estimated from fuel loading obtained from field measurements can be 30% to 200% more than when estimated using default field information. The increased buoyancy heat flux resulted in higher plume rise by 30% to 80%. This evaluation indicates that the regulatory air quality modeling system can replicate intensity and transport (horizontal and vertical) features for crop residue burning in this region when region-specific information is used to inform emissions and plume rise calculations. Further, previous vertical emissions allocation treatment of putting all cropland residue burning in the surface layer does not compare well with measured plume structure and these types of burns should be modeled more similarly to prescribed fires such that plume rise is based on an estimate of buoyancy. Copyright © 2018 Elsevier B.V. All rights reserved.

[Major Burn Trauma Management and Nursing Care].

PubMed

Lo, Shu-Fen

2015-08-01

Major burn injury is one of the most serious and often life-threatening forms of trauma. Burn patients not only suffer from the physical, psychological, social and spiritual impacts of their injury but also experience considerable changes in health-related quality of life. This paper presents a review of the literature on the implications of previous research and clinical care guidelines related to major burn injuries in order to help clinical practice nurses use evidence-based care guidelines to respond to initial injury assessments, better manage the complex systemic response to these injuries, and provide specialist wound care, emotional support, and rehabilitation services.

Debridement Techniques in Pediatric Trauma and Burn-Related Wounds

PubMed Central

Block, Lisa; King, Timothy W.; Gosain, Ankush

2015-01-01

Significance: Traumatic injuries are the leading cause of morbidity and mortality in children. The purpose of this review is to provide an overview of the initial assessment and management of traumatic and burn wounds in children. Special attention is given to wound cleansing, debridement techniques, and considerations for pain management and psychosocial support for children and families. Recent Advances: Basic and translational research over the last 5–7 years has advanced our knowledge related to the optimal care of acute pediatric traumatic and burn wounds. Data concerning methods, volume, solution and timing for irrigation of acute traumatic wounds, timing and methods of wound debridement, including hydrosurgery and plasma knife coblation, and wound dressings are presented. Additionally, data concerning the long-term psychosocial outcomes following acute injury are presented. Critical Issues: The care of pediatric trauma and burn-related wounds requires prompt assessment, pain control, cleansing, debridement, application of appropriate dressings, and close follow-up. Ideally, a knowledgeable multidisciplinary team cares for these patients. A limitation in the care of these patients is the relative paucity of data specific to the care of acute traumatic wounds in the pediatric population. Future Directions: Research is ongoing in the arenas of new debridement techniques and instruments, and in wound dressing technology. Dedicated research on these topics in the pediatric population will serve to strengthen and advance the care of pediatric patients with acute traumatic and burn wounds. PMID:26487978

BASS teardown

NASA Image and Video Library

2014-08-05

ISS040-E-088798 (5 Aug. 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, removes hardware for the combustion experiment known as the Burning and Suppression of Solids (BASS-II) from the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft. NASA astronaut Reid Wiseman, flight engineer, looks on.

BASS teardown

NASA Image and Video Library

2014-08-05

ISS040-E-088800 (5 Aug. 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, removes hardware for the combustion experiment known as the Burning and Suppression of Solids (BASS-II) from the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft. NASA astronaut Reid Wiseman, flight engineer, looks on.

BASS teardown

NASA Image and Video Library

2014-08-05

ISS040-E-088801 (5 Aug. 2014) --- European Space Agency astronaut Alexander Gerst, Expedition 40 flight engineer, removes hardware for the combustion experiment known as the Burning and Suppression of Solids (BASS-II) from the Microgravity Science Glovebox (MSG) in the Destiny laboratory of the International Space Station. The experiment seeks to provide insight on how flames burn in space compared to Earth which may provide fire safety benefits aboard future spacecraft. NASA astronaut Reid Wiseman, flight engineer, looks on.

Thermal properties

Treesearch

Roger M. Rowell

2005-01-01

The traditional question at the start of a class on thermal properties of wood is, “Does wood burn?” The students have all been warmed in front of a wood-burning fire before, so they are sure the answer is yes—but since the professor asked the question, there must be some hidden trick to the obvious answer. Going with their experience, their answer is “yes, wood burns...

Performance of ITER as a burning plasma experiment

NASA Astrophysics Data System (ADS)

Shimada, M.; Mukhovatov, V.; Federici, G.; Gribov, Y.; Kukushkin, A.; Murakami, Y.; Polevoi, A.; Pustovitov, V.; Sengoku, S.; Sugihara, M.

2004-02-01

Recent performance analysis has improved confidence in achieving Q (= fusion power/auxiliary heating power)geq 10 in inductive operation in ITER. Performance analysis based on empirical scalings shows the feasibility of achieving Q geq 10 in inductive operation, particularly with improved modelling of helium exhaust. Analysis has also indicated the possibility that ITER can potentially demonstrate Q ~ 50, enabling studies of self-heated plasmas. Theory-based core modelling indicates the need for a high pedestal temperature (3.2-5.3 keV) to achieve Q geq 10, which is in the range of projections with presently available pedestal scalings. Pellet injection from the high-field side would be useful in enhancing Q and reducing edge localized mode (ELM) heat load in high plasma current operation. If the ELM heat load is not acceptable, it could be made tolerable by further tilting the target plate. Steady state operation scenarios at Q = 5 have been developed with modest requirements on confinement improvement and beta (HH98(y,2) geq 1.3 and bgrN geq 2.6). Stabilization of the resistive wall modes (RWMs), required in such regimes, is feasible with the present saddle coils and power supplies with double-wall structures taken into account. Recent analysis shows a potential of high power steady state operation with a fusion power of 0.7 GW at Q ~ 8. Achievement of the required bgrN ~ 3.6 by RWM stabilization is a possibility. Further analysis is also needed on reduction of the divertor target heat load.

Inactivation of possible microorganism food contaminants on packaging foils using nonthermal plasma and hydrogen peroxide

NASA Astrophysics Data System (ADS)

Scholtz, V.; Khun, J.; Soušková, H.; Čeřovský, M.

2015-07-01

The inactivation effect of nonthermal plasma generated in electric discharge burning in air atmosphere with water or hydrogen peroxide aerosol for the application to the microbial decontamination of packaging foils is studied. The microbial inactivation is studied on two bacterial, two yeasts, and two filamentous micromycete species. The inactivation of all contaminating microorganisms becomes on the area of full 8.5 cm in diameter circular sample after short times of several tens of seconds. Described apparatus may present a possible alternative method of microbial decontamination of food packaging material or other thermolabile materials.

Inactivation of possible microorganism food contaminants on packaging foils using nonthermal plasma and hydrogen peroxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scholtz, V., E-mail: Vladimir.Scholtz@vscht.cz; Khun, J.; Soušková, H.

The inactivation effect of nonthermal plasma generated in electric discharge burning in air atmosphere with water or hydrogen peroxide aerosol for the application to the microbial decontamination of packaging foils is studied. The microbial inactivation is studied on two bacterial, two yeasts, and two filamentous micromycete species. The inactivation of all contaminating microorganisms becomes on the area of full 8.5 cm in diameter circular sample after short times of several tens of seconds. Described apparatus may present a possible alternative method of microbial decontamination of food packaging material or other thermolabile materials.

Impact of energetic-particle-driven geodesic acoustic modes on turbulence.

PubMed

Zarzoso, D; Sarazin, Y; Garbet, X; Dumont, R; Strugarek, A; Abiteboul, J; Cartier-Michaud, T; Dif-Pradalier, G; Ghendrih, Ph; Grandgirard, V; Latu, G; Passeron, C; Thomine, O

2013-03-22

The impact on turbulent transport of geodesic acoustic modes excited by energetic particles is evidenced for the first time in flux-driven 5D gyrokinetic simulations using the Gysela code. Energetic geodesic acoustic modes (EGAMs) are excited in a regime with a transport barrier in the outer radial region. The interaction between EGAMs and turbulence is such that turbulent transport can be enhanced in the presence of EGAMs, with the subsequent destruction of the transport barrier. This scenario could be particularly critical in those plasmas, such as burning plasmas, exhibiting a rich population of suprathermal particles capable of exciting energetic modes.

BASS Experiment Imagery

NASA Image and Video Library

2013-04-09

ISS035-E-015952 (10 April 2013) --- This is one of a series of close-up images photographed during a run of the Burning and Suppression of Solids (BASS) experiment onboard the Earth-orbiting International Space Station. Following a series of preparations, on April 5 NASA astronaut Chris Cassidy (out of frame) conducted several runs of the experiment, which examines the burning and extinction characteristics of a wide variety of fuel samples in microgravity. The experiment is planned for guiding strategies for extinguishing fires in microgravity. BASS results contribute to the combustion computational models used in the design of fire detection and suppression systems in microgravity and on Earth.

Applying stand replacement prescribed fires in Alaska

Treesearch

Larry A. Vanderlinden

1996-01-01

Stand replacement prescribed burning has been applied in Alaska on several occasions. Based on that experience, perspectives can be provided, issues can be discussed, and keys to success can be identified that are applicable to stand replacement prescribed burning activities in areas outside Alaska.

Impact of a Newly Implemented Burn Protocol on Surgically Managed Partial Thickness Burns at a Specialized Burns Center in Singapore.

PubMed

Tay, Khwee-Soon Vincent; Chong, Si-Jack; Tan, Bien-Keem

2016-03-01

This study evaluated the impact of a newly implemented protocol for superficial to mid-dermal partial thickness burns which involves early surgery and rapid coverage with biosynthetic dressing in a specialized national burns center in Singapore. Consecutive patients with 5% or greater total body surface area (TBSA) superficial to mid-dermal partial thickness burns injury admitted to the Burns Centre at the Singapore General Hospital between August and December 2014 for surgery within 48 hours of injury were prospectively recruited into the study to form the protocol group. Comparable historical cases from the year 2013 retrieved from the burns center audit database were used to form the historical control group. Demographics (age, sex), type and depth of burns, %TBSA burnt, number of operative sessions, and length of stay were recorded for each patient of both cohorts. Thirty-nine burns patients managed under the new protocol were compared with historical control (n = 39) comparable in age and extensiveness of burns. A significantly shorter length of stay (P < 0.05) per TBSA burns was observed in the new protocol group (0.74 day/%TBSA) versus historical control (1.55 day/%TBSA). Fewer operative sessions were needed under the new protocol for burns 10% or greater TBSA burns (P < 0.05). The authors report their promising experience with a newly implemented protocol for surgically managed burns patients which involves early surgery and appropriate use of biosynthetic dressing on superficial to mid-dermal partial thickness burns. Clinically, shorter lengths of stay, fewer operative sessions, and decreased need for skin grafting of burns patient were observed.

How is the chlorophyll count affected by burned and unburned marsh areas?

NASA Astrophysics Data System (ADS)

Kendrick, C.

2017-12-01

Does marsh burnings, either man made or natural, hinder or help Louisiana's vitally important coastal plant life? Does the carbon produced from the fires have a negative effect on the chlorophyll count of these precious living protective barriers? Or does it help contribute to raising the plants chlorophyll count? Along Louisiana's Gulf Coast, marsh burnings are conducted every 2-4 years to destroy some of the Spartina patens. Fires and smoke may have an effect on the chlorophyll count of the plants found in Louisiana's marshes. Peat burns, root burns, and cover burns are the three types of marsh fires. These burns can be either man made or started by natural causes. Peat burns occur when the soil is dry due to a drained marsh. Root burns occur when plant roots are burned without the soil being consumed. Cover burns occur when several centimeters of water covers the soil. Cover burns are often used by Wildlife and Fisheries personnel to promote preferred plant food growth like Scirpus olneyi rather than the dominant Spartina patens. Our project was conducted by testing marsh plants and obtaining chlorophyll count of both a burned (cover burn) and an unburned area. Approximately one year after the burn, in August 2015, we tested the burned area's site. We retested the same site in December 2016. The results from our testing showed that there was a slightly higher chlorophyll count in the burned area. The chlorophyll count average from the two testing days was 33.5 in the burned area and 30.15 in the unburned area. Our hypothesis was that the chlorophyll content of "controlled" burned wetland areas will have a higher amount than the "no" burn area. The experiment results supported this hypothesis by showing an increase of 3.35 average in the burned area.

Large Scale Flame Spread Environmental Characterization Testing

NASA Technical Reports Server (NTRS)

Clayman, Lauren K.; Olson, Sandra L.; Gokoghi, Suleyman A.; Brooker, John E.; Ferkul, Paul V.; Kacher, Henry F.

2013-01-01

Under the Advanced Exploration Systems (AES) Spacecraft Fire Safety Demonstration Project (SFSDP), as a risk mitigation activity in support of the development of a large-scale fire demonstration experiment in microgravity, flame-spread tests were conducted in normal gravity on thin, cellulose-based fuels in a sealed chamber. The primary objective of the tests was to measure pressure rise in a chamber as sample material, burning direction (upward/downward), total heat release, heat release rate, and heat loss mechanisms were varied between tests. A Design of Experiments (DOE) method was imposed to produce an array of tests from a fixed set of constraints and a coupled response model was developed. Supplementary tests were run without experimental design to additionally vary select parameters such as initial chamber pressure. The starting chamber pressure for each test was set below atmospheric to prevent chamber overpressure. Bottom ignition, or upward propagating burns, produced rapid acceleratory turbulent flame spread. Pressure rise in the chamber increases as the amount of fuel burned increases mainly because of the larger amount of heat generation and, to a much smaller extent, due to the increase in gaseous number of moles. Top ignition, or downward propagating burns, produced a steady flame spread with a very small flat flame across the burning edge. Steady-state pressure is achieved during downward flame spread as the pressure rises and plateaus. This indicates that the heat generation by the flame matches the heat loss to surroundings during the longer, slower downward burns. One heat loss mechanism included mounting a heat exchanger directly above the burning sample in the path of the plume to act as a heat sink and more efficiently dissipate the heat due to the combustion event. This proved an effective means for chamber overpressure mitigation for those tests producing the most total heat release and thusly was determined to be a feasible mitigation strategy to incorporate into the microgravity experiment.

Heterogeneous kinetics of N2O5 reactive uptake and chlorine activation in authentic biomass burning aerosol

NASA Astrophysics Data System (ADS)

Sullivan, R. C.; Jahl, L.; Goldberger, L.; Ahern, A.; Thornton, J. A.

2017-12-01

Nitryl chloride (ClNO2) is a nighttime reservoir of NOx that is formed from the uptake of dinitrogen pentoxide (N2O5) into particles containing chloride. The formation of ClNO2 from heterogeneous reactions of N2O5(g) with authentic biomass burning aerosol has not previously been studied. We observed the rapid production of N2O5 and then ClNO2 during dark chemical transformations of biomass burning aerosol produced from a variety of fuels using both a smog chamber and an aerosol flow tube reactor. Iodide adduct chemical ionization mass spectrometry was used to measure gas phase ClNO2 and N2O5, and acetate chemical ionization mass spectrometry to measure gaseous HCl and other compounds, while a soot particle aerosol mass spectrometer measured changes in aerosol composition as chloride was displaced by nitrate. Upon the addition of ozone to the biomass burning smoke, N2O5 was always rapidly formed and ClNO2 was subsequently detected in the gas phase. During experiments at high relative humidity, we observed decreases in particulate chloride and increases in particulate nitrate which we believe are due to acid displacement of HCl(g) by HNO3 since no additional ClNO2 was produced in the gas phase. The reactive uptake probability of N2O5 on authentic biomass burning aerosol and the yield of ClNO2 were determined for the first time using chamber and flow tube experiments on smoke from biomass fuels including sawgrass, giant cutgrass, palmetto leaves, and ponderosa pine. These experiments confirm the formation of N2O5 and ClNO2 in biomass burning emissions and suggest that biomass burning is a likely source of continental ClNO2 and HCl.

Civilian blast-related burn injuries

PubMed Central

Patel, J.N.; Tan, A.; Dziewulski, P.

2016-01-01

Summary There is limited English literature describing the experience of a civilian hospital managing blast-related burn injuries. As the largest regional burn unit, we reviewed our cases with the aim of identifying means to improve current management. A 6-year retrospective analysis of all patients coded as sustaining blast-related burns was conducted through the unit’s burns database. Medical case notes were reviewed for information on burn demographics, management and outcomes. 42 patients were identified. Male to female ratio was 37:5. Age range was 12-84 years, (mean=33 years). Total body surface area (%TBSA) burn ranged from 0.25% to 60%, (median=1%). The most common burn injury was flame (31/42, 73.8%). Gas explosions were the most common mechanism of injury (19 cases; 45.2%). 7/42 cases (16.7%) had full ATLS management pre-transfer to the burns unit. The Injury Severity Score (ISS) ranged from 0-43 (median=2). 17/42 (40.4%) patients required admission. 37/36 (88.1%) patients were managed conservatively of which 1 patient later required surgery due to deeper burns. 5/42 (11.9%) patients required surgical management at presentation and these were noted to be burns with >15% TBSA requiring resuscitation. One case required emergency escharotomies and finger amputations. All patients survived their burn injuries. Blast-related burn injuries are generally uncommon in the civilian setting. Following proper assessment, most of these cases can be deemed as minor injuries and managed conservatively. Improvement in burns management education and training at local emergency departments would provide efficient patient care and avoid unnecessary referrals to a burns unit. PMID:27857651

Patient experiences of burn scars in adults and children and development of a health-related quality of life conceptual model: A qualitative study.

PubMed

Simons, Megan; Price, Nathaniel; Kimble, Roy; Tyack, Zephanie

2016-05-01

The aim of this study was to understand the impact of burn scars on health-related quality of life (HRQOL) from the perspective of adults and children with burn scars, and caregivers to inform the development of a conceptual model of burn scar HRQOL. Twenty-one participants (adults and children) with burn scars and nine caregivers participated in semi-structured, face-to-face interviews between 2012 and 2013. During the interviews, participants were asked to describe features about their (or their child's) burn scars and its impact on everyday life. Two coders conducted thematic analysis, with consensus achieved through discussion and review with a third coder. The literature on HRQOL models was then reviewed to further inform the development of a conceptual model of burn scar HRQOL. Five themes emerged from the qualitative data: 'physical and sensory symptoms', 'impact of burn scar interventions', 'impact of burn scar symptoms', 'personal factors' and 'change over time'. Caregivers offered further insights into family functioning after burn, and the impacts of burn scars and burn scar interventions on family life. In the conceptual model, symptoms (sensory and physical) of burn scars are considered proximal to HRQOL, with distal indicators including functioning (physical, emotional, social, cognitive), individual factors and the environment. Overall quality of life was affected by HRQOL. Understanding the impact of burn scars on HRQOL and the development of a conceptual model will inform future burn scar research and clinical practice. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

On the condition of UO2 nuclear fuel irradiated in a PWR to a burn-up in excess of 110 MWd/kgHM

NASA Astrophysics Data System (ADS)

Restani, R.; Horvath, M.; Goll, W.; Bertsch, J.; Gavillet, D.; Hermann, A.; Martin, M.; Walker, C. T.

2016-12-01

Post-irradiation examination results are presented for UO2 fuel from a PWR fuel rod that had been irradiated to an average burn-up of 105 MWd/kgHM and showed high fission gas release of 42%. The radial distribution of xenon and the partitioning of fission gas between bubbles and the fuel matrix was investigated using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and electron probe microanalysis. It is concluded that release from the fuel at intermediate radial positions was mainly responsible for the high fission gas release. In this region thermal release had occurred from the high burn-up structure (HBS) at some point after the sixth irradiation cycle. The LA-ICP-MS results indicate that gas release had also occurred from the HBS in the vicinity of the pellet periphery. It is shown that the gas pressure in the HBS pores is well below the pressure that the fuel can sustain.

Burning Graphene Layer-by-Layer

PubMed Central

Ermakov, Victor A.; Alaferdov, Andrei V.; Vaz, Alfredo R.; Perim, Eric; Autreto, Pedro A. S.; Paupitz, Ricardo; Galvao, Douglas S.; Moshkalev, Stanislav A.

2015-01-01

Graphene, in single layer or multi-layer forms, holds great promise for future electronics and high-temperature applications. Resistance to oxidation, an important property for high-temperature applications, has not yet been extensively investigated. Controlled thinning of multi-layer graphene (MLG), e.g., by plasma or laser processing is another challenge, since the existing methods produce non-uniform thinning or introduce undesirable defects in the basal plane. We report here that heating to extremely high temperatures (exceeding 2000 K) and controllable layer-by-layer burning (thinning) can be achieved by low-power laser processing of suspended high-quality MLG in air in “cold-wall” reactor configuration. In contrast, localized laser heating of supported samples results in non-uniform graphene burning at much higher rates. Fully atomistic molecular dynamics simulations were also performed to reveal details of oxidation mechanisms leading to uniform layer-by-layer graphene gasification. The extraordinary resistance of MLG to oxidation paves the way to novel high-temperature applications as continuum light source or scaffolding material. PMID:26100466

Leachate Geochemical Results for Ash and Burned Soil Samples from the October 2007 Southern California Wildfires

USGS Publications Warehouse

Hageman, Philip L.; Plumlee, Geoffrey S.; Martin, Deborah A.; Hoefen, Todd M.; Meeker, Gregory P.; Adams, Monique; Lamothe, Paul J.; Anthony, Michael W.

2008-01-01

This report is the second release of leachate geochemical data included as part of a multidisciplinary study of ash and burned soil samples from the October 2007 wildfires in southern California. Geochemical data for the first set of samples were released in an Open-File Report (Plumlee and others, 2007). This study is a continuation of that work. The objectives of this leaching study are to aid in understanding the interactions of ash and burned soil with rainfall. For this study, 12 samples collected in early November 2007 were leached using the U.S. Geological Survey (USGS) Field Leach Test (FLT). Following leaching, sub-samples of the leachate were analyzed for pH and specific conductance. The leachate was then filtered, and aliquots were preserved for geochemical analysis. This report presents leachate geochemical data for pH, specific conductance, alkalinity, anions using ion chromatography (I.C.), cations using inductively coupled plasma?atomic mass spectrometry (ICP-MS), and mercury by continuous flow injection?cold vapor?atomic fluorescence (CVAFS).

Midazolam Exacerbates Morphine Tolerance and Morphine-induced Hyperactive Behaviors in Young Rats with Burn Injury

PubMed Central

Song, Li; Wang, Shuxing; Zuo, Yunxia; Chen, Lucy; Martyn, Jeevendra A.; Mao, Jianren

2014-01-01

Midazolam and morphine are often used in pediatric intensive care unit (ICU) for analgesia and sedation. However, how these two drugs interact behaviorally remains unclear. Here, we examined whether 1) co-administration of midazolam with morphine would exacerbate morphine tolerance and morphine-induced hyperactive behaviors, and 2) protein kinase C (PKC) would contribute to these behavioral changes. Male rats of 3 to 4 weeks old were exposed to a hindpaw burn injury. In Experiment 1, burn-injured young rats received once daily saline or morphine (10 mg/kg, subcutaneous, s.c.), followed 30 min later by either saline or midazolam (2 mg/kg, intraperitoneal, i.p.), for 14 days beginning 3 days after burn injury. In Experiment 2, young rats with burn injury were administered with morphine (10 mg/kg, s.c.), midazolam (2 mg/kg, i.p.), and chelerythrine chloride (a non-specific PKC inhibitor 10 nmol, intrathecal) for 14 days. For both experiments, cumulative morphine anti-nociceptive dose-response (ED50) was tested and hyperactive behaviors such as jumping and scratching were recorded. Following 2 weeks of each treatment, ED50 dose was significantly increased in rats receiving morphine alone as compared with rats receiving saline or midazolam alone. The ED50 dose was further increased in rats receiving both morphine and midazolam. Co-administration of morphine and midazolam also exacerbated morphine-induced hyperactive behaviors. Expression of the NR1 subunit of the N-methyl-D-aspartate (NMDA) receptor and PKCγ in the spinal cord dorsal horn (immunohistochemistry; Western blot) was upregulated in burn-injured young rats receiving morphine alone or in combination with midazolam, and chelerythrine prevented the development of morphine tolerance. These results indicate that midazolam exacerbated morphine tolerance through a spinal NMDA/PKC-mediated mechanism. PMID:24713351